Prevalence of Inadequate Immunity to Measles, Mumps, Rubella, and Varicella in MLB and NBA Athletes.

Science.gov (United States)

Conway, Justin J; Toresdahl, Brett G; Ling, Daphne I; Boniquit, Nicole T; Callahan, Lisa R; Kinderknecht, James J

2018-05-01

Multiple outbreaks of vaccine-preventable viral diseases have occurred in professional sports in recent years. Currently, there is no established protocol for vaccination or immunity screening for professional athletes. There are significant differences in the prevalence of inadequate immunity dependent on age, sport, country of birth, and participation in collegiate sports. Cross-sectional cohort study. Level 4. A sample of Major League Baseball (MLB) and National Basketball Association (NBA) players were screened for serologic evidence of immunity to measles, mumps, rubella, and varicella prior to the 2015 and 2016 seasons. The results were designated as adequate (immune) or inadequate (equivocal or nonimmune) based on laboratory criteria. Comparison with an age-matched control group was performed using data from the National Health and Nutrition Examination Survey (NHANES). A total of 98 athletes (62 MLB, 36 NBA) were screened. The prevalence of inadequate immunity for any virus was 35.5% in MLB players and 33.3% in NBA players. There was a significantly greater risk of inadequate immunity to rubella (risk ratio, 6.38; P < 0.01) and varicella (risk ratio, 4.21; P < 0.01) in athletes compared with the age-matched NHANES population. Our analysis did not reveal differences in rates of immunity based on sport, country of birth (US born vs international), or participation in college athletics. There was a lower rate of inadequate immunity to varicella with increasing age (odds ratio, 0.72; P = 0.05). One-third of athletes studied had inadequate immunity to 1 of the 4 viruses tested. Younger players had a significantly greater risk of inadequate immunity to varicella. Birth outside the US and lack of participation in college athletics were not found to influence immunity rates. These results can inform the development of future screening programs to prevent outbreaks of viral infections in professional athletes.

Designing with residual materials

NARCIS (Netherlands)

Walhout, W.; Wever, R.; Blom, E.; Addink-Dölle, L.; Tempelman, E.

2013-01-01

Many entrepreneurial businesses have attempted to create value based on the residual material streams of third parties. Based on ‘waste’ materials they designed products, around which they built their company. Such activities have the potential to yield sustainable products. Many of such companies

Risk factors for and consequences of inadequate surgical margins in oral squamous cell carcinoma

DEFF Research Database (Denmark)

Lawaetz, Mads; Homøe, Preben

2014-01-01

OBJECTIVE: The purpose of this study was to examine which factors are associated with inadequate surgical margins and to assess the postoperative consequences. STUDY DESIGN: A retrospective cohort of 110 patients with oral squamous cell carcinoma treated with surgery during a 2-year period...

Free Material Design with Multiple Load Cases

DEFF Research Database (Denmark)

Pedersen, Pauli; Pedersen, Niels Leergaard

2012-01-01

Multiple load cases and the consideration of strength is a reality that most structural designs are exposed to. Improved possibility to produce specific materials, say by fiber lay-up, put focus on research on free material optimization. A formulation for such design problems together with a prac......Multiple load cases and the consideration of strength is a reality that most structural designs are exposed to. Improved possibility to produce specific materials, say by fiber lay-up, put focus on research on free material optimization. A formulation for such design problems together...... with a practical recursive design procedure is presented and illustrated with examples. The presented finite element analysis involve many elements as well as many load cases. Separating the local amount of material from a description with unit trace for the local anisotropy, gives the free materials formulation...... a more physical interpretation of the material constraint....

Materials design data for fusion reactors

International Nuclear Information System (INIS)

Tavassoli, A.A.F.

1998-01-01

Design data needed for fusion reactors are characterized by the diversity of materials and the complexity of loading situations found in these reactors. In addition, advanced fabrication techniques, such as hot isostatic pressing, envisaged for fabrication of single and multilayered in-vessel components, could significantly change the original materials properties for which the current design rules are written. As a result, additional materials properties have had to be generated for fusion reactors and new structural design rules formulated. This paper recalls some of the materials properties data generated for ITER and DEMO, and gives examples of how these are converted into design criteria. In particular, it gives specific examples for the properties of 316LN-IG and modified 9Cr-1Mo steels, and CuCrZr alloy. These include, determination of tension, creep, isochronous, fatigue, and creep-fatigue curves and their analysis and conversion into design limits. (orig.)

Materials design data for fusion reactors

Energy Technology Data Exchange (ETDEWEB)

Tavassoli, A.A.F. [CEA Commissariat a l`Energie Atomique, Gif sur Yvette (France). CEREM

1998-10-01

Design data needed for fusion reactors are characterized by the diversity of materials and the complexity of loading situations found in these reactors. In addition, advanced fabrication techniques, such as hot isostatic pressing, envisaged for fabrication of single and multilayered in-vessel components, could significantly change the original materials properties for which the current design rules are written. As a result, additional materials properties have had to be generated for fusion reactors and new structural design rules formulated. This paper recalls some of the materials properties data generated for ITER and DEMO, and gives examples of how these are converted into design criteria. In particular, it gives specific examples for the properties of 316LN-IG and modified 9Cr-1Mo steels, and CuCrZr alloy. These include, determination of tension, creep, isochronous, fatigue, and creep-fatigue curves and their analysis and conversion into design limits. (orig.) 19 refs.

Designing Instructional Materials: Some Guidelines.

Science.gov (United States)

Burbank, Lucille; Pett, Dennis

Guidelines for the design of instructional materials are outlined in this paper. The principles of design are presented in five major categories: (1) general design (structural appeal and personal appeal); (2) instructional design (attention, memory, concept learning, and attitude change); (3) visual design (media considerations, pictures, graphs…

Design and computation of modern engineering materials

CERN Document Server

Altenbach, Holm

2014-01-01

 The idea of this monograph is to present the latest results related to design and computation of engineering materials and structures. The contributions cover the classical fields of mechanical, civil and materials engineering up to biomechanics and advanced materials processing and optimization. The materials and structures covered can be categorized into modern steels and titanium alloys, composite materials, biological and natural materials, material hybrids and modern joining technologies. Analytical modelling, numerical simulation, the application of state-of-the-art design tools and sophisticated experimental techniques are applied to characterize the performance of materials and to design and optimize structures in different fields of engineering applications.

Design criteria tank farm storage and staging facility

International Nuclear Information System (INIS)

Lott, D.T.

1995-01-01

Tank Farms Operations must store/stage material and equipment until work packages are ready to work. Consumable materials are also required to be stored for routine and emergency work. Safety issues based on poor housekeeping and material deterioration due to weather damage has resulted from inadequate storage space. It has been determined that a storage building in close proximity to the Tank Farm work force would be cost effective. This document provides the design criteria for the design of the storage and staging buildings near 272AW and 272WA buildings

Shape Does Matter : Designing materials in products

NARCIS (Netherlands)

Saakes, D.P.

2010-01-01

In this thesis I investigate how to support designing the appearance of materials in products, specifically how to search for new materials and to explore the interactions between materials and shape. Central in this thesis is a novel design called Skin 2.0. Skin allows designers in the early

Designed materials: what and how

Science.gov (United States)

Mazumder, Jyotirmoy; Dutta, Debasish; Ghosh, Amit K.; Kikuchi, Noboru

2003-03-01

Quest for a material to suit the service performance is almost as old as human civilization. So far materials engineers have developed a series of alloys, polymers, ceramics, and composites to serve many of the performance requirements in a modern society. However, challenges appear when one needs to satisfy more than one boundary condition. For example, a component with negative Coefficient of Thermal Expansion (CTE) using a ductile metal was almost impossible until recently. Synthesis of various technologies such as Direct Metal Deposition (DMD) Homogenization Design Method (HDM) and mutli material Computer Aided Design (CAD) was necessary to achieve this goal. Rapid fabrication of three-dimensional shapes of engineering materials such as H13 tool steel and nickel super alloys are now possible using Direct Materials Deposition (DMD) technique as well as similar techniques such as Light Engineered New Shaping (LENS) or Directed Light Fabrication (DLF). However, DMD has closed loop capability that enables better dimension and thermal cycle control. This enables one to deposit different material at different pixels with a given height directly from a CAD drawing. The feedback loop also controls the thermal cycle. H13 tool steel is one of the difficult alloys for deposition due to residual stress accumulation from martensitic transformation. However, it is the material of choice for the die and tool industry. DMD has demonstrated successful fabrication of complicated shapes and dies and tools, even with H13 alloys. This process also offers copper chill blocks and water-cooling channels as the integral part of the tool. On the other hand ZrO2 was co-deposited with nickel super alloys using DMD. Flexibility of the process is enormous and essentially it is an enabling technology to marterialize many a design. Using DMD in conjunction with HDM and multi-material CAD, one can produce components with predetermined performance such as negative co-efficient of expansion, by

Clinical significance of inadequate endometrial biopsies prior to hysterectomy.

Science.gov (United States)

Turney, Emily H; Farghaly, Hanan; Eskew, Ashley M; Parker, Lynn P; Milam, Michael R

2012-01-01

To evaluate preoperative clinical risk factors associated with significant uterine histopathologic abnormalities in final hysterectomy specimens in patients with inadequate preoperative endometrial biopsies. This is an institutional review board-approved, retrospective cohort analysis of 469 consecutive patients who underwent preoperative endometrial biopsies with subsequent hysterectomy from January 1, 2005, to December 31, 2009, at the University of Louisville Medical Center. We analyzed risk factors for inadequate biopsy and for final diagnosis of endometrial pathology (defined as endometrial hyperplasia or uterine cancer). Of the 469 preoperative endometrial biopsies reviewed, 26.2% (123/469) were inadequate (IBx) and 73.8% (346/469) were adequate and benign. IBx on endometrial biopsies was associated with a greater risk of having significant uterine histopathologic abnormalities on final hysterectomy specimens (6.5% vs. 2.3%, RR 2.8 [95% CI 1.1-7.3], p = 0.04). Although inadequate endometrial biopsies are a common finding, they can be associated with significant uterine histopathologic abnormalities on final hysterectomy specimens.

Consequences of Inadequate Physical Activity

Centers for Disease Control (CDC) Podcasts

2018-03-27

Listen as CDC Epidemiologist Susan Carlson, PhD, talks about her research, which estimates the percentage of US deaths attributed to inadequate levels of physical activity.  Created: 3/27/2018 by Preventing Chronic Disease (PCD), National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 3/27/2018.

The Influence of Inadequate Teacher-to-Student Social Support on Amotivation of Physical Education Students

Science.gov (United States)

Shen, Bo; Li, Weidong; Sun, Haichun; Rukavina, Paul Bernard

2010-01-01

Guided by Green-Demers, Leagult, Pelletier, and Pelletier's (2008) assumption that amotivation (absence of motivation) is a multidimensional construct, we designed this study to investigate the influence of inadequate teacher-to-student social support on amotivation of high-school physical education students. Five hundred and sixty-six ninth…

Design of solar drying-plant for bulk material drying

Directory of Open Access Journals (Sweden)

Peter Horbaj

2008-11-01

Full Text Available A generally well-known high energy requirement for technological processes of drying and the fact that the world’s supplyof the conventional energy sources has considerably decreased are the decisive factors forcing us to look for some new, if possible,renewable energy sources for this process by emphasising their environmental reliability. One of the possibilities how to replace, atleast partly, the conventional energy sources – heat in a drying process is solar energy.Air-drying of bulk materials usually has a series of disadvantages such as time expenditure, drying defects in the bulk materialand inadequate final moisture content. A method that obviates or reduces the disadvantages of air-drying and, at the same time, reducesthe costs of kiln drying, is drying with solar heat. Solar energy can replace a large part of this depletable energy since solar energy cansupply heat at the temperatures most often used to dry bulk material. Solar drying-plant offer an attractive solution.

Nano-Scale Positioning Design with Piezoelectric Materials

Directory of Open Access Journals (Sweden)

Yung Yue Chen

2017-12-01

Full Text Available Piezoelectric materials naturally possess high potential to deliver nano-scale positioning resolution; hence, they are adopted in a variety of engineering applications widely. Unfortunately, unacceptable positioning errors always appear because of the natural hysteresis effect of the piezoelectric materials. This natural property must be mitigated in practical applications. For solving this drawback, a nonlinear positioning design is proposed in this article. This nonlinear positioning design of piezoelectric materials is realized by the following four steps: 1. The famous Bouc–Wen model is utilized to present the input and output behaviors of piezoelectric materials; 2. System parameters of the Bouc–Wen model that describe the characteristics of piezoelectric materials are simultaneously identified with the particle swam optimization method; 3. Stability verification for the identified Bouc–Wen model; 4. A nonlinear feedback linearization control design is derived for the nano-scale positioning design of the piezoelectric material, mathematically. One important contribution of this investigation is that the positioning error between the output displacement of the controlled piezoelectric materials and the desired trajectory in nano-scale level can be proven to converge to zero asymptotically, under the effect of the hysteresis.

Rational design of reconfigurable prismatic architected materials

Science.gov (United States)

Overvelde, Johannes T. B.; Weaver, James C.; Hoberman, Chuck; Bertoldi, Katia

2017-01-01

Advances in fabrication technologies are enabling the production of architected materials with unprecedented properties. Most such materials are characterized by a fixed geometry, but in the design of some materials it is possible to incorporate internal mechanisms capable of reconfiguring their spatial architecture, and in this way to enable tunable functionality. Inspired by the structural diversity and foldability of the prismatic geometries that can be constructed using the snapology origami technique, here we introduce a robust design strategy based on space-filling tessellations of polyhedra to create three-dimensional reconfigurable materials comprising a periodic assembly of rigid plates and elastic hinges. Guided by numerical analysis and physical prototypes, we systematically explore the mobility of the designed structures and identify a wide range of qualitatively different deformations and internal rearrangements. Given that the underlying principles are scale-independent, our strategy can be applied to the design of the next generation of reconfigurable structures and materials, ranging from metre-scale transformable architectures to nanometre-scale tunable photonic systems.

Materials design and development of functional materials for industry

International Nuclear Information System (INIS)

Asahi, Ryoji; Morikawa, Takeshi; Hazama, Hirofumi; Matsubara, Masato

2008-01-01

It is now well recognized that we are witnessing a golden age of innovation with novel materials, with discoveries that are important for both basic science and industry. With the development of theory along with computing power, quantum materials design-the synthesis of materials with the desired properties in a controlled way via materials engineering on the atomic scale-is becoming a major component of materials research. Computational prediction based on first-principles calculations has helped to find an efficient way to develop materials that are much needed for industry, as we have seen in the successful development of visible-light sensitized photocatalysts and thermoelectric materials. Close collaboration between theory and experiment is emphasized as an essential for success

Evidence Report: Risk Factor of Inadequate Nutrition

Science.gov (United States)

Smith, Scott M.; Zwart, Sara R.; Heer, Martina

2015-01-01

The importance of nutrition in exploration has been documented repeatedly throughout history, where, for example, in the period between Columbus' voyage in 1492 and the invention of the steam engine, scurvy resulted in more sailor deaths than all other causes of death combined. Because nutrients are required for the structure and function of every cell and every system in the body, defining the nutrient requirements for spaceflight and ensuring provision and intake of those nutrients are primary issues for crew health and mission success. Unique aspects of nutrition during space travel include the overarching physiological adaptation to weightlessness, psychological adaptation to extreme and remote environments, and the ability of nutrition and nutrients to serve as countermeasures to ameliorate the negative effects of spaceflight on the human body. Key areas of clinical concern for long-duration spaceflight include loss of body mass (general inadequate food intake), bone and muscle loss, cardiovascular and immune system decrements, increased radiation exposure and oxidative stress, vision and ophthalmic changes, behavior and performance, nutrient supply during extravehicular activity, and general depletion of body nutrient stores because of inadequate food supply, inadequate food intake, increased metabolism, and/or irreversible loss of nutrients. These topics are reviewed herein, based on the current gap structure.

The automated design of materials far from equilibrium

Science.gov (United States)

Miskin, Marc Z.

Automated design is emerging as a powerful concept in materials science. By combining computer algorithms, simulations, and experimental data, new techniques are being developed that start with high level functional requirements and identify the ideal materials that achieve them. This represents a radically different picture of how materials become functional in which technological demand drives material discovery, rather than the other way around. At the frontiers of this field, materials systems previously considered too complicated can start to be controlled and understood. Particularly promising are materials far from equilibrium. Material robustness, high strength, self-healing and memory are properties displayed by several materials systems that are intrinsically out of equilibrium. These and other properties could be revolutionary, provided they can first be controlled. This thesis conceptualizes and implements a framework for designing materials that are far from equilibrium. We show how, even in the absence of a complete physical theory, design from the top down is possible and lends itself to producing physical insight. As a prototype system, we work with granular materials: collections of athermal, macroscopic identical objects, since these materials function both as an essential component of industrial processes as well as a model system for many non-equilibrium states of matter. We show that by placing granular materials in the context of design, benefits emerge simultaneously for fundamental and applied interests. As first steps, we use our framework to design granular aggregates with extreme properties like high stiffness, and softness. We demonstrate control over nonlinear effects by producing exotic aggregates that stiffen under compression. Expanding on our framework, we conceptualize new ways of thinking about material design when automatic discovery is possible. We show how to build rules that link particle shapes to arbitrary granular packing

Virtual Reality for Materials Design Laboratory

Data.gov (United States)

Federal Laboratory Consortium — The purpose is to research and develop materials through applied virtual reality to enable interactive "materials-by-design." Extensive theoretical and computational...

Heat stress and inadequate sanitary facilities at workplaces – an occupational health concern for women?

Science.gov (United States)

Venugopal, Vidhya; Rekha, Shanmugam; Manikandan, Krishnamoorthy; Latha, Perumal Kamalakkannan; Vennila, Viswanathan; Ganesan, Nalini; Kumaravel, Perumal; Chinnadurai, Stephen Jeremiah

2016-01-01

Background Health concerns unique to women are growing with the large number of women venturing into different trades that expose them to hot working environments and inadequate sanitation facilities, common in many Indian workplaces. Objective The study was carried out to investigate the health implications of exposures to hot work environments and inadequate sanitation facilities at their workplaces for women workers. Design A cross-sectional study was conducted with 312 women workers in three occupational sectors in 2014–2015. Quantitative data on heat exposures and physiological heat strain indicators such as core body temperature (CBT), sweat rate (SwR), and urine specific gravity (USG) were collected. A structured questionnaire captured workers perceptions about health impacts of heat stress and inadequate sanitary facilities at the workplace. Results Workplace heat exposures exceeded the threshold limit value for safe manual work for 71% women (Avg. wet bulb globe temperature=30°C±2.3°C) during the study period. Eighty-seven percent of the 200 women who had inadequate/no toilets at their workplaces reported experiencing genitourinary problems periodically. Above normal CBT, SwR, and USG in about 10% women workers indicated heat strain and moderate dehydration that corroborated well with their perceptions. Observed significant associations between high-heat exposures and SwR (t=−2.3879, p=0.0192), inadequate toilet facilities and self-reported adverse heat-related health symptoms (χ2=4.03, p=0.0444), and prevalence of genitourinary issues (χ2=42.92, p=0.0005×10−7) reemphasize that heat is a risk and lack of sanitation facilities is a major health concern for women workers. Conclusions The preliminary evidence suggests that health of women workers is at risk due to occupational heat exposures and inadequate sanitation facilities at many Indian workplaces. Intervention through strong labor policies with gender sensitivity is the need of the hour to

Heat stress and inadequate sanitary facilities at workplaces – an occupational health concern for women?

Directory of Open Access Journals (Sweden)

Vidhya Venugopal

2016-09-01

Full Text Available Background: Health concerns unique to women are growing with the large number of women venturing into different trades that expose them to hot working environments and inadequate sanitation facilities, common in many Indian workplaces. Objective: The study was carried out to investigate the health implications of exposures to hot work environments and inadequate sanitation facilities at their workplaces for women workers. Design: A cross-sectional study was conducted with 312 women workers in three occupational sectors in 2014–2015. Quantitative data on heat exposures and physiological heat strain indicators such as core body temperature (CBT, sweat rate (SwR, and urine specific gravity (USG were collected. A structured questionnaire captured workers perceptions about health impacts of heat stress and inadequate sanitary facilities at the workplace. Results: Workplace heat exposures exceeded the threshold limit value for safe manual work for 71% women (Avg. wet bulb globe temperature=30°C±2.3°C during the study period. Eighty-seven percent of the 200 women who had inadequate/no toilets at their workplaces reported experiencing genitourinary problems periodically. Above normal CBT, SwR, and USG in about 10% women workers indicated heat strain and moderate dehydration that corroborated well with their perceptions. Observed significant associations between high-heat exposures and SwR (t=−2.3879, p=0.0192, inadequate toilet facilities and self-reported adverse heat-related health symptoms (χ2=4.03, p=0.0444, and prevalence of genitourinary issues (χ2=42.92, p=0.0005×10−7 reemphasize that heat is a risk and lack of sanitation facilities is a major health concern for women workers. Conclusions: The preliminary evidence suggests that health of women workers is at risk due to occupational heat exposures and inadequate sanitation facilities at many Indian workplaces. Intervention through strong labor policies with gender sensitivity is the

Optimal Design of Porous Materials

DEFF Research Database (Denmark)

Andreassen, Erik

The focus of this thesis is topology optimization of material microstructures. That is, creating new materials, with attractive properties, by combining classic materials in periodic patterns. First, large-scale topology optimization is used to design complicated three-dimensional materials......, throughout the thesis extra attention is given to obtain structures that can be manufactured. That is also the case in the final part, where a simple multiscale method for the optimization of structural damping is presented. The method can be used to obtain an optimized component with structural details...

Design tools and materials in creative work

DEFF Research Database (Denmark)

Hansen, Nicolai Brodersen; Dalsgaard, Peter; Halskov, Kim

2017-01-01

-oriented perspectives, we wish to examine the potentials and limitations in current uses of design tools and materials, and discuss and explore when and how we can introduce ones. Participation in the workshop requires participants to document and analyse central themes in a case, and the resulting material will serve......This workshop aims to examine and discuss the role and nature of design tools and materials in creative work, and to explore how novel tools can meaningfully combine existing and novel tools to support and augment creative work. By exploring and combining methodological, theoretical, and design...

Material mediation and embodied actions in collaborative design process

Directory of Open Access Journals (Sweden)

Henna Lahti

2016-02-01

Full Text Available Material and embodied practices are an intrinsic part of craft and design education. This article reports a study in which textile teacher-students designed three-dimensional toys based on children’s drawings. Three students in each team worked on the given materials and designed the shape of the toy together. Materials for designing were either: 1 pen and paper, 2 masking tape and thin cardboard, or 3 wire and non-woven interfacing fabric. After the modelling phase, the final toys were created by sewing. Research data consisted of the video recordings of three design sessions representing the various design materials given to the students. By conducting multiple levels of analysis, we examined how the participants used materials and gestures to support their communication. The results highlight the strengths of 3D modelling techniques, particularly through comparison with the drawing technique undertaken by one design team. We found that simple material tools support students’ design process and suggest this could be applied to other design settings.

Wind energy: Overcoming inadequate wind and modeling uncertainties

Energy Technology Data Exchange (ETDEWEB)

Kane, Vivek

2010-09-15

'Green Energy' is the call of the day, and significance of Wind Energy can never be overemphasized. But the key question here is - What if the wind resources are inadequate? Studies reveal that the probability of finding favorable wind at a given place on land is only 15%. Moreover, there are inherent uncertainties associated with wind business. Can we overcome inadequate wind resources? Can we scientifically quantify uncertainty and model it to make business sense? This paper proposes a solution, by way of break-through Wind Technologies, combined with advanced tools for Financial Modeling, enabling vital business decisions.

Design to Robotic Production for Informed Materialization Processes

Directory of Open Access Journals (Sweden)

Sina Mostafavi

2017-12-01

Full Text Available Design to Robotic Production (D2RP establishes links between digital design and production in order to achieve informed materialization at an architectural scale. D2RP research is being discussed under the computation, automation and materialization themes, by reference to customizable digital design means, robotic fabrication setups and informed materialization strategies implemented by the Robotic Building group at Hyperbody, TU Delft.

ITER status, design and material objectives

International Nuclear Information System (INIS)

Aymar, R.

2002-01-01

During the ITER Engineering Design Activities (EDA), completed in July 2001, the Joint Central Team and Home Teams developed a robust design of ITER, summarised in this paper, with parameters which fully meet the required scientific and technological objectives, construction costs and safety requirements, with appropriate margins. The design is backed by R and D to qualify the technology, including materials R and D. Materials for ITER components have been selected largely because of their availability and well-established manufacturing technologies, taking account of the low fluence experienced during neutron irradiation, and the experimental nature of the device. Nevertheless, for specific needs relevant to a future fusion reactor, improved materials, in particular for magnet structures, in-vessel components, and joints between the different materials needed for plasma facing components, have been successfully developed. Now, with the technical readiness to decide on ITER construction, negotiations, supported by coordinated technical activities of an international team and teams from participant countries, are underway on joint construction of ITER with a view to the signature/ratification of an agreement in 2003

Security of fissile materials in Russia

International Nuclear Information System (INIS)

Bukharin, O.

1996-01-01

The problem of security of huge stocks of weapons-usable highly enriched uranium and plutonium in Russia against theft or diversion remains a serious nonproliferation concern. During the Cold War, the security of Soviet nuclear materials was based on centralization and discipline, protection by the military, and intrusive political oversight of the people. The recent fundamental societal changes have rendered these arrangements inadequate, and the security of nuclear materials has decreased. Safeguarding nuclear materials in Russia is particularly difficult because of their very large inventories and the size and complexity of the nation's nuclear infrastructure. Russia needs a reliable and more objective technology-based system of nuclear safeguards designed to control nuclear materials. The Russian government and the international community are working towards this goal

Inadequate exercise as a risk factor for sepsis mortality.

Science.gov (United States)

Williams, Paul T

2013-01-01

Test whether inadequate exercise is related to sepsis mortality. Mortality surveillance of an epidemiological cohort of 155,484 National Walkers' and Runners' Health Study participants residing in the United States. Deaths were monitored for an average of 11.6-years using the National Death index through December 31, 2008. Cox proportional hazard analyses were used to compare sepsis mortality (ICD-10 A40-41) to inadequate exercise (<1.07 METh/d run or walked) as measured on their baseline questionnaires. Deaths occurring within one year of the baseline survey were excluded. Sepsis was the underlying cause in 54 deaths (sepsis(underlying)) and a contributing cause in 184 deaths (sepsis(contributing)), or 238 total sepsis-related deaths (sepsis(total)). Inadequate exercise was associated with 2.24-fold increased risk for sepsis(underlying) (95%CI: 1.21 to 4.07-fold, P = 0.01), 2.11-fold increased risk for sepsis(contributing) (95%CI: 1.51- to 2.92-fold, P<10(-4)), and 2.13-fold increased risk for sepsis(total) (95%CI: 1.59- to 2.84-fold, P<10(-6)) when adjusted for age, sex, race, and cohort. The risk increase did not differ significantly between runners and walkers, by sex, or by age. Sepsis(total) risk was greater in diabetics (P = 10(-5)), cancer survivors (P = 0.0001), and heart attack survivors (P = 0.003) and increased with waist circumference (P = 0.0004). The sepsis(total) risk associated with inadequate exercise persisted when further adjusted for diabetes, prior cancer, prior heart attack and waist circumference, and when excluding deaths with cancer, or cardiovascular, respiratory, or genitourinary disease as the underlying cause. Inadequate exercise also increased sepsis(total) risk in 2163 baseline diabetics (4.78-fold, 95%CI: 2.1- to 13.8-fold, P = 0.0001) when adjusted, which was significantly greater (P = 0.03) than the adjusted risk increase in non-diabetics (1.80-fold, 95%CI: 1.30- to 2.46-fold, P = 0

Mass of materials: the impact of designers on construction ergonomics.

Science.gov (United States)

Smallwood, John

2012-01-01

Many construction injuries are musculoskeletal related in the form of sprains and strains arising from the handling of materials, which are specified by designers. The paper presents the results of a study conducted among delegates attending two 'designing for H&S' (DfH&S) seminars using a questionnaire. The salient findings include: the level of knowledge relative to the mass and density of materials is limited; designers generally do not consider the mass and density of materials when designing structures and elements and specifying materials; to a degree designers appreciate that the mass and density of materials impact on construction ergonomics; designers rate their knowledge of the mass and density of materials as limited, and designers appreciate the potential of the consideration of the mass and density of materials to contribute to an improvement in construction ergonomics. Conclusions include: designers lack the requisite knowledge relative to the mass and density of materials; designers are thus precluded from conducting optimum design hazard identification and risk assessments, and tertiary built environment designer education does not enlighten designers relative to construction ergonomics. Recommendations include: tertiary built environment designer education should construction ergonomics; professional associations should raise the level of awareness relative to construction ergonomics, and design practices should include a category 'mass and density of materials' in their practice libraries.

Extending ITER materials design to welded joints

Energy Technology Data Exchange (ETDEWEB)

Tavassoli, A.-A.F. [DMN/Dir, CEA/Saclay, Commissariat a l' Energie Atomique, 91191 Gif sur Yvette cedex (France)]. E-mail: tavassoli@cea.fr

2007-08-01

This paper extends the ITER materials properties documentation to weld metals and incorporates the needs of Test Blanket Modules for higher temperature materials properties. Since the main structural material selected for ITER is type 316L(N)-IG, the paper is focused on weld metals and joining techniques for this steel. Materials properties data are analysed according to the French design and construction rules for nuclear components (RCC-MR) and design allowables are equally derived using the same rules. Particular attention is paid to the type of weld metal, to the type and position of welding and their influence on the materials properties data and design allowables. The primary goal of this work, starting with 19-12-2 weld metal, is to produce comprehensive materials properties documentations that when combined with codification and inspection documents would satisfy ITER licensing needs. As a result, structural stability and capability of welded joints during manufacturing of ITER components and their subsequent service, including the effects of irradiation and eventual incidental or accidental situations, are also covered.

Bionic Design, Materials and Performance of Bone Tissue Scaffolds

Directory of Open Access Journals (Sweden)

Tong Wu

2017-10-01

Full Text Available Design, materials, and performance are important factors in the research of bone tissue scaffolds. This work briefly describes the bone scaffolds and their anatomic structure, as well as their biological and mechanical characteristics. Furthermore, we reviewed the characteristics of metal materials, inorganic materials, organic polymer materials, and composite materials. The importance of the bionic design in preoperative diagnosis models and customized bone scaffolds was also discussed, addressing both the bionic structure design (macro and micro structure and the bionic performance design (mechanical performance and biological performance. Materials and performance are the two main problems in the development of customized bone scaffolds. Bionic design is an effective way to solve these problems, which could improve the clinical application of bone scaffolds, by creating a balance between mechanical performance and biological performance.

Molecular designing of nanoparticles and functional materials

Directory of Open Access Journals (Sweden)

Ignjatović Nenad L.

2017-01-01

Full Text Available The interdisciplinary research team implemented the program titled “Molecular designing of nanoparticles with controlled morphological and physicochemical characteristics and functional materials based on them” (MODENAFUNA, between 2011 and 2016, gaining new knowledge significant to the further improvement of nanomaterials and nanotechnologies. It gathered under its umbrella six main interrelated topics pertaining to the design and control of morphological and physicochemical properties of nanoparticles and functional material based on them using new methods of synthesis and processing: 1 inorganic nanoparticles, 2 cathode materials for lithium-ion batteries, 3 functional ceramics with improved electrical and optical properties, 4 full density nanostructured calcium phosphate and functionally-graded materials, 5 nano-calcium phosphate in bone tissue engineering and 6 biodegradable micro- and nano-particles for the controlled delivery of medicaments. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. III45004: Molecular designing of nanoparticles with controlled morphological and physicochemical characteristics and functional materials based on them

Thermoelectric nanomaterials materials design and applications

CERN Document Server

Koumoto, Kunihito

2014-01-01

Presently, there is an intense race throughout the world to develop good enough thermoelectric materials which can be used in wide scale applications. This book focuses comprehensively on very recent up-to-date breakthroughs in thermoelectrics utilizing nanomaterials and methods based in nanoscience. Importantly, it provides the readers with methodology and concepts utilizing atomic scale and nanoscale materials design (such as superlattice structuring, atomic network structuring and properties control, electron correlation design, low dimensionality, nanostructuring, etc.). Furthermore, also

Materials data base as an interface between fusion reactor designs and materials development

International Nuclear Information System (INIS)

Ishino, S.; Iwata, S.

1983-01-01

The materials data base is an integrated information system of experimental and/or calculated data of materials being compiled to meet the broad needs for materials data by taking advantage of the data base management systems. In this paper the objective of such computerized data base is described from the viewpoint of materials engineers and fusion system designers. Materials data spread themselves widely from the field that relates fundamental understanding of the behaviors of electrons, atoms, vacancies, dislocations and so on to the performance of components, devices, machines and systems. In our approach this information is described as ''relations'' by a set of tables which comprise related variables, for example, a set of values about essential properties for materials selection. This approach based on the relational model enables relational operations, i.e. SELECTION, PROJECTION, JOIN and so on, to select suitable materials, to set trade-off parameters for system designers and to establish design criteria. Stored data comprise (i) fundamental properties for all elements and potential structural materials, (ii) low cycle fatigue, irradiation creep and swelling data for type 316 stainless steels. These data have been selected and evaluated from critical reviews of existing data base of about 2 mega bytes data, some examples of materials selections and extraction of trade-off parameters are shown as a subject of critical issue concerning how to bridge the large gap between materials developments and system designs. (author)

46 CFR 58.05-1 - Material, design and construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Material, design and construction. 58.05-1 Section 58.05... AUXILIARY MACHINERY AND RELATED SYSTEMS Main Propulsion Machinery § 58.05-1 Material, design and construction. (a) The material, design, construction, workmanship, and arrangement of main propulsion machinery...

Using learning materials for design-based interventions

DEFF Research Database (Denmark)

Gissel, Stig Toke

2015-01-01

This article considers a methodological issue concerning the use of learning materials for interventions in design-based research. When the researcher uses existing or creates new didacticised learning materials for research purposes and tests their applicability in authentic contexts, many...... variables are in play. When using or designing a learning material a lot of choices have to be made and effects are difficult to isolate. The advantage of using learning materials for interventions is that results could have high ecological validity. In the article this methodological issue is exemplified...... through a research project using and developing digital learning materials for developing literacy in the early grades. One of many important choices to be made in elaborating this learning material concerns which texts should be used for supporting students’ literacy development in the lower grades...

Review of ASME-NH Design Materials for Creep-Fatigue

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Kim, Jong Bum

2010-01-01

To review and recommend the candidate design materials for the Sodium-Cooled Fast Reactor, the material sensitivity evaluations by the comparison of design data between the ASME-NH materials were performed by using the SIE ASME-NH computer program implementing the material database of the ASME-NH. The design material data provided by the ASME-NH code are the elastic modulus and yield Strength, Time-Independent Allowable Stress Intensity value, time-dependent allowable stress intensity value, expected minimum stress-to rupture value, stress rupture Factors for weldment, isochronous stress-strain curves, and design fatigue curves. Among these, the data related with the creep-fatigue evaluation are investigated in this study

The Plastic Bakery : A Case of Material Driven Design

NARCIS (Netherlands)

Majumdar, P.; Karana, E.; Sonneveld, M.H.; Karana, E.; Giaccardi, E.; Nimkulrat, N.; Niedderer, K.; Camere, S.

2017-01-01

A growing number of scholars argue that understanding how people experience materials in products, i.e. Materials Experience, is essential in
designing meaningful material applications. Material Driven Design (MDD) has been developed as the method to understand these experiential traits
of

The socio-materiality of designing organizational change

DEFF Research Database (Denmark)

Stang Våland, Marianne; Georg, Susse

2014-01-01

Purpose – The purpose of this paper is to examine the managerial implications of adopting a design attitude to organizational change. Design/methodology/approach – Based on an ethnographic study of a merger, the paper investigates the intricate interplay between architectural design...... and organizational change in the context of physically relocating an organization to a new office building. Emphasis is given to the socio-materiality of this double design process. Findings – The data suggests that taking a design attitude toward managing organizational change can allow different actors...... to participate in organizational design processes, releasing management from its traditional role as the keeper of the design solution. Research limitations/implications – Although based on a single case, the paper provides insights into the socio-materiality of organizational change that is relevant in other...

Structural and microstructural design in brittle materials

International Nuclear Information System (INIS)

Evans, A.G.

1979-12-01

Structural design with brittle materials requires that the stress level in the component correspond to a material survival probability that exceeds the minimum survival probability permitted in that application. This can be achieved by developing failure models that fully account for the probability of fracture from defects within the material (including considerations of fracture statistics, fracture mechanics and stress analysis) coupled with non-destructive techniques that determine the size of the large extreme of critical defects. Approaches for obtaining the requisite information are described. The results provide implications for the microstructural design of failure resistant brittle materials by reducing the size of deleterious defects and enhancing the fracture toughness

Implications of materials behavior on design codes

International Nuclear Information System (INIS)

Roberts, D.I.

1981-01-01

In the U.S., the design of Class 1 elevated-temperature components of reactor systems is governed by the rules of ASME Boiler and Pressure Vessel Cases N47 (design) and N48 (construction). The rules of Case N47, in particular, are sophisticated and complex, and a substantial quantity of materials behavior data is needed to design to these rules. Requirements include a detailed knowledge of creep, rupture, creep-fatigue, etc. In addition, many other factors, including such aspects as the influence on service performance of environment, welds, and fabrication-induced cold work, must be considered in the design. This paper reviews the impact of some recent HTGR materials data on design rules and approaches. (Auth.)

Workshop on materials control and accounting system design

International Nuclear Information System (INIS)

Pillay, K.K.S.

1989-01-01

The chapter describes the workshop aimed at reinforcing, through participation in the design exercise, the concepts of nuclear materials control and accountability. Topics include: workshop format; key elements of a materials management and accounting (MC and A) system; and MC and A system design including safeguards organization and management, material access areas, key measurement points, nuclear materials measurements, physical inventory, material balance closings, and internal controls. Appended to this chapter is a detailed description of a facility that produces metallic plutonium and the safeguards requirements for this facility

Composite materials design and applications

CERN Document Server

Gay, Daniel; Tsai, Stephen W

2002-01-01

PART ONE. PRINCIPLES OF CONSTRUCTIONCOMPOSITE MATERIALS, INTEREST AND PROPERTIESWhat is Composite Material Fibers and MatrixWhat can be Made Using Composite Materials?Typical Examples of Interest on the Use of Composite MaterialsExamples on Replacing Conventional Solutions with CompositesPrincipal Physical PropertiesFABRICATION PROCESSESMolding ProcessesOther Forming ProcessesPractical Hints in the Manufacturing ProcessesPLY PROPERTIESIsotropy and AnisotropyCharacteristics of the Reinforcement-Matrix MixtureUnidirectional PlyWoven FabricsMats and Reinforced MatricesMultidimensional FabricsMetal Matrix CompositesTestsSANDWICH STRUCTURES:What is a Sandwich Structure?Simplified FlexureA Few Special AspectsFabrication and Design ProblemsNondestructive Quality ControlCONCEPTION AND DESIGNDesign of a Composite PieceThe LaminateFailure of LaminatesSizing of LaminatesJOINING AND ASSEMBLYRiveting and BoltingBondingInsertsCOMPOSITE MATERIALS AND AEROSPACE CONSTRUCTIONAircraftHelicoptersPropeller Blades for AirplanesTur...

The significance of inadequate transcranial Doppler studies in children with sickle cell disease.

Directory of Open Access Journals (Sweden)

Simon Greenwood

Full Text Available Sickle cell disease (SCD is a common cause of cerebrovascular disease in childhood. Primary stroke prevention is effective using transcranial Doppler (TCD scans to measure intracranial blood velocities, and regular blood transfusions or hydroxycarbamide when these are abnormal. Inadequate TCD scans occur when it is not possible to measure velocities in all the main arteries. We have investigated the prevalence and significance of this in a retrospective audit of 3915 TCD scans in 1191 children, performed between 2008 and 2015. 79% scans were normal, 6.4% conditional, 2.8% abnormal and 12% inadequate. 21.6% of 1191 patients had an inadequate scan at least once. The median age of first inadequate scan was 3.3 years (0.7-19.4, with a U-shaped frequency distribution with age: 28% aged 2-3 years, 3.5% age 10 years, 25% age 16 years. In young children reduced compliance was the main reason for inadequate TCDs, whereas in older children it was due to a poor temporal ultrasound window. The prevalence of inadequate TCD was 8% in the main Vascular Laboratory at King's College Hospital and significantly higher at 16% in the outreach clinics (P<0.0001, probably due to the use of a portable ultrasound machine. Inadequate TCD scans were not associated with underlying cerebrovascular disease.

Friction material composites copper-metal-free material design perspective

CERN Document Server

Sundarkrishnaa, K L

2015-01-01

This book examines material composites used in connection with brake friction, their design and safety. To aid in understanding, the essentials of friction are explained. This second edition was extended to include friction material composites without copper, as they offer an environmentally friendlier option. The second edition is intended to support beginners by offering insights into the essentials of friction material composites, helping them to develop a broader understanding of brake friction materials. Friction materials find wide-ranging applications in household and industrial appliances, brake pads for automotive applications, rail brake friction pads and composition brake blocks. This second edition is an introductory volume to a set of related books, and is based on the author’s experience and expertise with various material manufacturers, brake manufacturers, vehicle manufacturers, researchers and testing labs around the world with which the author has been associated for the past 28 years.

Inadequate humidification of respiratory gases during mechanical ventilation of the newborn.

Science.gov (United States)

Tarnow-Mordi, W O; Sutton, P; Wilkinson, A R

1986-01-01

Proximal airway humidity was measured during mechanical ventilation in 14 infants using an electronic hygrometer. Values below recommended minimum humidity of adult inspired gas were recorded on 251 of 396 occasions. Inadequate humidification, largely due to inadequate proximal airway temperature, is commoner than recognised in infants receiving mechanical ventilation. PMID:3740912

Initial treatment of severe malaria in children is inadequate – a study ...

African Journals Online (AJOL)

-medicated at home. Initial consultations are at primary local health facilities where less effective drugs are prescribed at inadequate dosages. Recommended ACTs were also often prescribed at inadequate dosages. Education in the use of ...

Material and design considerations of FBGA reliability performance

International Nuclear Information System (INIS)

Lee, Teck Kheng; Ng, T.C.; Chai, Y.M.

2004-01-01

FBGA package reliability is usually assessed through the conventional approaches of die attach and mold compound material optimization. However, with the rapid changes and fast-moving pace of electronic packaging and the introduction of new soldermask and core materials, substrate design has also become a critical factor in determining overall package reliability. The purpose of this paper is to understand the impact design and soldermask material of a rigid substrate on overall package reliability. Three different soldermask patterns with a matrix of different die attach, mold compound, and soldermask materials are assessed using the moisture sensitivity test (MST). Package reliability is also assessed through the use of temperature cycling (T/C) at conditions 'B' and 'C'. For material optimization, three different mold compounds and die attach materials are used. Material adhesion between different die attach materials and soldermask materials are obtained through die shear performed at various temperatures and preset moisture conditions. A study correlating the different packaging material properties and their relative adhesion strengths with overall package reliability in terms of both MST and T/C performance was performed. Soldermask design under the die pads was found to affect package reliability. For example, locating vias at the edge of the die is not desirable because the vias acts as initiation point for delamination and moisture-induced failure. Through die shear testing, soldermask B demonstrated higher adhesion properties compared to soldermask A across several packaging materials and enhanced the overall package reliability in terms of both MST and T/C performance. Both MST JEDEC level 1 and the T/C of 'B' and 'C' at 1000 cycles have been achieved through design and package material optimization

Implications of materials behavior on design codes

International Nuclear Information System (INIS)

Roberts, D.I.

1981-04-01

In the US, the design of Class 1 elevated-temperature components of reactor systems is governed by the rules of ASME Boiler and Pressure Vessel Cases N47 (design) and N48 (construction). The rules of Case N47, in particular, are sophisticated and complex, and a substantial quantity of materials behavior data is needed to design to these rules. Requirements include a detailed knowledge of creep, rupture, creep-fatigue, etc. In addition, many other factors, including such aspects as the influence on service performance of environment, welds, and fabrication-induced cold work, must be considered in the design. This paper reviews the impact of some recent HTGR materials data on design rules and approaches. In the construction area, for example, recent data regarding the elevated-temperature properties and behavior of cold-formed austenitic materials such as Alloy 800H have resulted in rule changes. Observed creep-fatigue behavior of Alloy 800H and 2-1/4Cr to 1Mo steel is causing active review of the pertinence of linear damage summation approaches

New ways of integrating material knowledge into the design process

DEFF Research Database (Denmark)

Højris, Anders; Nielsen, Louise Møller

2013-01-01

– based on technical performance, no longer apply. Accordingly the approach in this paper is to view information and knowledge about materials through the perspective of organizational memory and technology brokering. This paper is build upon two cases from the German based design studio: designaffairs...... libraries and thereby access to information on new material possibilities has also changed the way designers integrate knowledge about materials into the design process. This means that the traditional design process model, where the selection of materials takes place after the design of form and function...... in order to help clients to find the right material among hundreds of samples. Furthermore a number of material libraries have also been developed into online database, which provides detailed information about new material and makes the information accessible from almost everywhere. The access to material...

Determinants of inadequate fruit and vegetable consumption amongst Portuguese adults.

Science.gov (United States)

Oliveira, A; Maia, B; Lopes, C

2014-04-01

A low consumption of fruit and vegetables (F&V) represents a high burden on health. The present study evaluates sociodemographic, lifestyle and anthropometric determinants of an inadequate consumption of F&V (Diet was assessed by a validated food frequency questionnaire. Odds ratios (ORs) and 95% confidence intervals (CIs) were calculated by logistic regression, after sex stratification and controlling for age, education, marital status, smoking, regular physical exercise and total energy intake. Older women and men had 37% and 67%, respectively, lower odds of inadequate F&V consumption (≥65 versus 12 versus excessive alcohol (women: ≥15 g day(-1) ; men: ≥30 g day(-1) ) presented a two- and four-fold higher probability of having inadequate F&V consumption compared to nondrinkers (OR = 1.95, 95% CI = 1.38-2.77 in women; OR = 4.40, 95% CI = 2.70-7.18 in men). In both sexes, an inadequate consumption of F&V was more frequently found in younger, less educated and less physically active subjects with smoking and drinking habits. Strategies aiming to increase F&V consumption should consider these target groups that present a clustering of unhealthy lifestyles. © 2013 The British Dietetic Association Ltd.

A study on technical issues of materials and design bases in ASME section III subsection NH code

International Nuclear Information System (INIS)

Lee, Hyeong Yeon; Kim, Jong Bum; Yoo, Bong

2000-12-01

In this study, an analysis of evaluation report by ORNL on the technical issues of elevated temperatures design guide line, ASME Code Section III Subsection NH was conducted and a brief evaluation procedure of the creep-fatigue damage was presented. ORNL published the report in 1993 and reviewed the issue areas where code rules or regulatory guides may be lacking or inadequate to ensure safe operation over the expected life cycles for liquid metal reactor systems. From historical viewpoint of the ASME NH code development, ASME Code Case 47 was changed much in 1989 edition, which includes the stress relaxation behavior in creep damage evaluation. Afterwards the 1992 version of CC N-47 was upgraded to Subsection NH in 1995 edition, which is the same with that of CC N-47 1992 edition except few material data. This report brings up the technical and regulatory issues that can not guarantee the safe and reliable operation of the ALMR which got the conceptual design certification from NRC. Twenty three technical issues were raised and settlement methodology were proposed. Additionally, the status of items approved by ASME code subgroup of elevated temperature design committee for the revision of the most recent 1998 edition of ASME NH was described

The innovative application studty on eco-packaging design and materials

Directory of Open Access Journals (Sweden)

Cui Yong Min

2016-01-01

Full Text Available The paper solves the increasingly deteriorate environmental problems by positively exploring how to utilize and develop eco-packaging design reasonably. The paper explores an effective method that combines eco-packaging and environmental protection materials, hoping to define the sustainable development road of packaging design. The paper is centered on the design application of eco-packaging and environmental protection materials, applies and analyzes the method to obtain innovative design requirements and development tendency of eco-packaging design by analyzing status and significance of eco-packaging design, combining with the development and main types of eco-packaging packaging materials, and based on the achievements acquired by eco-packaging and environmental protection materials. Meanwhile, the paper also reveals mutual dependence and mutual promotion of eco-packaging design and eco-packaging materials.

Internet addiction: reappraisal of an increasingly inadequate concept.

Science.gov (United States)

Starcevic, Vladan; Aboujaoude, Elias

2017-02-01

This article re-examines the popular concept of Internet addiction, discusses the key problems associated with it, and proposes possible alternatives. The concept of Internet addiction is inadequate for several reasons. Addiction may be a correct designation only for the minority of individuals who meet the general criteria for addiction, and it needs to be better demarcated from various patterns of excessive or abnormal use. Addiction to the Internet as a medium does not exist, although the Internet as a medium may play an important role in making some behaviors addictive. The Internet can no longer be separated from other potentially overused media, such as text messaging and gaming platforms. Internet addiction is conceptually too heterogeneous because it pertains to a variety of very different behaviors. Internet addiction should be replaced by terms that refer to the specific behaviors (eg, gaming, gambling, or sexual activity), regardless of whether these are performed online or offline.

Post-implementation review of inadequate core cooling instrumentation

International Nuclear Information System (INIS)

Anderson, J.L.; Anderson, R.L.; Hagen, E.W.; Morelock, T.C.; Huang, T.L.; Phillips, L.E.

1988-01-01

Studies of Three Mile Island (TMI) accident identified the need for additional instrumentation to detect inadequate core cooling (ICC) in nuclear power plants. Industry studies by plant owners and reactor vendors supported the conclusion that improvements were needed to help operators diagnose the approach to or existence of ICC and to provide more complete information for operator control of safety injection, flow to minimize the consequences of such an accident. In 1980, the US Nuclear Regulatory Commission (NRC) required further studies by the industry and described ICC instrumentation design requirements that included human factors and environmental considerations. On December 10, 1982, NRC issued to Babcock and Wilcox (BandW) licensees' orders for Modification of License and transmitted to all pressurized water reactor (PWR) licensees Generic Letter 82-28 to inform them of the revised NRC requirements. The instrumentation requirements for detection of ICC include upgraded subcooling margin monitors (SMMs), upgraded core exit thermocouples (CETs), and installation of a reactor coolant inventory tracking system (RCITS)

Inverse design of dielectric materials by topology optimization

DEFF Research Database (Denmark)

Otomori, M.; Andkjær, Jacob Anders; Sigmund, Ole

2012-01-01

The capabilities and operation of electromagnetic devices can be dramatically enhanced if artificial materials that provide certain prescribed properties can be designed and fabricated. This paper presents a systematic methodology for the design of dielectric materials with prescribed electric...... permittivity. A gradient-based topology optimization method is used to find the distribution of dielectric material for the unit cell of a periodic microstructure composed of one or two dielectric materials. The optimization problem is formulated as a problem to minimize the square of the difference between...

DESIGN OF PARTICULATE MATERIAL COMPACTOR ROLLS DIAMETER

Directory of Open Access Journals (Sweden)

Peter Peciar

2017-09-01

Full Text Available At present, in a period of an industrial expansion great emphasis is placed on the environment. That means aiming for a reduced energy consumption, and also lessening dustiness from very fine powder material. This category also includes particulate material agglomeration processes. Because this process is very energy-intensive, it is necessary to correctly design these devices. The aim of this paper is to focus on a theoretical design of a production compactor with the rolls diameter for an experimental particulate material, based on Johanson’s theory and experimentally measured material properties. The material used for experimental measurements was an NPK-based industrial fertilizer consisting of several components. The results of this paper is the dependence of the ratio of the maximum compression pressure to the initial compression pressure from the rolls diameter of the proposed compactor.

Material and design considerations of FBGA reliability performance

Energy Technology Data Exchange (ETDEWEB)

Lee, Teck Kheng; Ng, T.C.; Chai, Y.M

2004-09-01

FBGA package reliability is usually assessed through the conventional approaches of die attach and mold compound material optimization. However, with the rapid changes and fast-moving pace of electronic packaging and the introduction of new soldermask and core materials, substrate design has also become a critical factor in determining overall package reliability. The purpose of this paper is to understand the impact design and soldermask material of a rigid substrate on overall package reliability. Three different soldermask patterns with a matrix of different die attach, mold compound, and soldermask materials are assessed using the moisture sensitivity test (MST). Package reliability is also assessed through the use of temperature cycling (T/C) at conditions 'B' and 'C'. For material optimization, three different mold compounds and die attach materials are used. Material adhesion between different die attach materials and soldermask materials are obtained through die shear performed at various temperatures and preset moisture conditions. A study correlating the different packaging material properties and their relative adhesion strengths with overall package reliability in terms of both MST and T/C performance was performed. Soldermask design under the die pads was found to affect package reliability. For example, locating vias at the edge of the die is not desirable because the vias acts as initiation point for delamination and moisture-induced failure. Through die shear testing, soldermask B demonstrated higher adhesion properties compared to soldermask A across several packaging materials and enhanced the overall package reliability in terms of both MST and T/C performance. Both MST JEDEC level 1 and the T/C of 'B' and 'C' at 1000 cycles have been achieved through design and package material optimization.

Advances in wind turbine blade design and materials

DEFF Research Database (Denmark)

Wind energy is gaining critical ground in the area of renewable energy, with wind energy being predicted to provide up to 8% of the world’s consumption of electricity by 2021. Advances in wind turbine blade design and materials reviews the design and functionality of wind turbine rotor blades...... as well as the requirements and challenges for composite materials used in both current and future designs of wind turbine blades. Part one outlines the challenges and developments in wind turbine blade design, including aerodynamic and aeroelastic design features, fatigue loads on wind turbine blades......, and characteristics of wind turbine blade airfoils. Part two discusses the fatigue behavior of composite wind turbine blades, including the micromechanical modelling and fatigue life prediction of wind turbine blade composite materials, and the effects of resin and reinforcement variations on the fatigue resistance...

Mechanical and materials engineering of modern structure and component design

CERN Document Server

Altenbach, Holm

2015-01-01

This book presents the latest findings on mechanical and materials engineering as applied to the design of modern engineering materials and components. The contributions cover the classical fields of mechanical, civil and materials engineering, as well as bioengineering and advanced materials processing and optimization. The materials and structures discussed can be categorized into modern steels, aluminium and titanium alloys, polymers/composite materials, biological and natural materials, material hybrids and modern nano-based materials. Analytical modelling, numerical simulation, state-of-the-art design tools and advanced experimental techniques are applied to characterize the materials’ performance and to design and optimize structures in different fields of engineering applications.

Candidate container materials for Yucca Mountain waste package designs

International Nuclear Information System (INIS)

McCright, R.D.; Halsey, W.G.; Gdowski, G.E.; Clarke, W.L.

1991-09-01

Materials considered as candidates for fabricating nuclear waste containers are reviewed in the context of the Conceptual Design phase of a potential repository located at Yucca Mountain. A selection criteria has been written for evaluation of candidate materials for the next phase -- Advanced Conceptual Design. The selection criteria is based on the conceptual design of a thin-walled container fabricated from a single metal or alloy; the criteria consider the performance requirements on the container and the service environment in which the containers will be emplaced. A long list of candidate materials is evaluated against the criteria, and a short list of materials is proposed for advanced characterization in the next design phase

Fiber-reinforced composites materials, manufacturing, and design

CERN Document Server

Mallick, P K

2007-01-01

The newly expanded and revised edition of Fiber-Reinforced Composites: Materials, Manufacturing, and Design presents the most up-to-date resource available on state-of-the-art composite materials. This book is unique in that it not only offers a current analysis of mechanics and properties, but also examines the latest advances in test methods, applications, manufacturing processes, and design aspects involving composites. This third edition presents thorough coverage of newly developed materials including nanocomposites. It also adds more emphasis on underlying theories, practical methods, and problem-solving skills employed in real-world applications of composite materials. Each chapter contains new examples drawn from diverse applications and additional problems to reinforce the practical relevance of key concepts. New in The Third Edition: Contains new sections on material substitution, cost analysis, nano- and natural fibers, fiber architecture, and carbon-carbon composites Provides a new chapter on poly...

Barriers to Mammography among Inadequately Screened Women

Science.gov (United States)

Stoll, Carolyn R. T.; Roberts, Summer; Cheng, Meng-Ru; Crayton, Eloise V.; Jackson, Sherrill; Politi, Mary C.

2015-01-01

Mammography use has increased over the past 20 years, yet more than 30% of women remain inadequately screened. Structural barriers can deter individuals from screening, however, cognitive, emotional, and communication barriers may also prevent mammography use. This study sought to identify the impact of number and type of barriers on mammography…

Material constraints on high-speed design

Science.gov (United States)

Bucur, Diana; Militaru, Nicolae

2015-02-01

Current high-speed circuit designs with signal rates up to 100Gbps and above are implying constraints for dielectric and conductive materials and their dependence of frequency, for component elements and for production processes. The purpose of this paper is to highlight through various simulation results the frequency dependence of specific parameters like insertion and return loss, eye diagrams, group delay that are part of signal integrity analyses type. In low-power environment designs become more complex as the operation frequency increases. The need for new materials with spatial uniformity for dielectric constant is a need for higher data rates circuits. The fiber weave effect (FWE) will be analyzed through the eye diagram results for various dielectric materials in a differential signaling scheme given the fact that the FWE is a phenomenon that affects randomly the performance of the circuit on balanced/differential transmission lines which are typically characterized through the above mentioned approaches. Crosstalk between traces is also of concern due to propagated signals that have tight rise and fall times or due to high density of the boards. Criteria should be considered to achieve maximum performance of the designed system requiring critical electronic properties.

Effect of inadequate ferrule segment location on fracture resistance of endodontically treated teeth

Directory of Open Access Journals (Sweden)

Satheesh B Haralur

2018-01-01

Full Text Available Introduction: The circumferential 2 mm ferrule during the fabrication of the crown is strongly advocated for the long-term clinical success. During the routine clinical practice, the dentist encounters the endodontically treated tooth (ETT with inadequacy of the ferrule in some segment due to caries, abrasion, and erosions. The aim of this in vitro study was to investigate the consequence of inadequate segmental ferrule location on fracture strength of the root canal-treated anterior and posterior teeth. Materials and Methods: Fifty each maxillary canine and mandibular premolar intact human teeth were root canal treated and sectioned at 2 mm above the cementum-enamel junction. The teeth samples were divided into 5 groups of 10 each. The G-I and G-V samples had the 360° ferrule and complete absence of the ferrule, respectively. The G-II had the inadequate ferrule on the palatal surface, while G-III and G-IV had inadequate ferrule at buccal and proximal area. Teeth samples were subsequently restored with glass-reinforced fiber post, composite core, and full veneer metal crown. The samples were tested with universal testing machine under static load to record the fracture resistance. The acquired data were subjected to ANOVA and Tukey's post hoc statistical analysis. Results: The G-I with circumferential ferrule showed the higher fracture resistance. The teeth samples with lack of the ferrule had the least fracture resistance. Among the segmental absence of ferrule, teeth samples with lack of the proximal ferrule were least affected. Deficiency of a ferrule on the lingual wall significantly affected the fracture strength in both anterior and posterior ETT. Conclusions: The ETT with sectional inadequacy of the ferrule is significantly more effective in resisting the fracture in comparison to the complete absence of the ferrule.

Relationship between health services, socioeconomic variables and inadequate weight gain among Brazilian children.

Science.gov (United States)

de Souza, A C; Peterson, K E; Cufino, E; Gardner, J; Craveiro, M V; Ascherio, A

1999-01-01

This ecological analysis assessed the relative contribution of behavioural, health services and socioeconomic variables to inadequate weight gain in infants (0-11 months) and children (12-23 months) in 140 municipalities in the State of Ceara, north-east Brazil. To assess the total effect of selected variables, we fitted three unique sets of multivariate linear regression models to the prevalence of inadequate weight gain in infants and in children. The final predictive models included variables from the three sets. Findings showed that participation in growth monitoring and urbanization were inversely and significantly associated with the prevalence of inadequate weight gain in infants, accounting for 38.3% of the variation. Female illiteracy rate, participation in growth monitoring and degree of urbanization were all positively associated with prevalence of inadequate weight gain in children. Together, these factors explained 25.6% of the variation. Our results suggest that efforts to reduce the average municipality-specific female illiteracy rate, in combination with participation in growth monitoring, may be effective in reducing municipality-level prevalence of inadequate weight gain in infants and children in Ceara.

Inadequate functional health literacy in Spanish as a barrier to cervical cancer screening among immigrant Latinas in New York City.

Science.gov (United States)

Garbers, Samantha; Chiasson, Mary Ann

2004-10-01

The objective of this study was to examine the association between inadequate functional health literacy in Spanish among low-income Latinas aged 40 and older and cervical cancer screening knowledge and behavior. Spanish-speaking Latinas aged 40-78 of various nationalities (n = 205) participated in a study that included a survey on cervical cancer knowledge and behavior administered in Spanish and the Spanish version of the Test of Functional Health Literacy in Adults. Compared to those with adequate and marginal health literacy, women with inadequate functional health literacy in Spanish were significantly less likely to have ever had a Papanicolaou (Pap) test (odds ratio, 0.12; 95% confidence interval [CI], 0.04-0.37) or in the last three years (odds ratio, 0.35; 95% CI, 0.18-0.68) and were significantly more likely to have had their last Pap test at a local public hospital (odds ratio, 2.43; 95% CI, 1.18-4.97). Even when controlling for other factors, women with inadequate health literacy were 16.7 times less likely (adjusted odds ratio, 0.06; 95% CI, 0.01-0.55) to have ever had a Pap test. Almost half of the population we studied will have difficulty interpreting written medical materials, even in Spanish. When developing efforts to reach women who have not been screened, programs and service providers need to be aware that the women most in need of information about screening may be more likely to be unable to read any written materials provided to them, regardless of the language or level of simplicity of the materials. Programs and strategies need to be implemented to increase screening prevalence and to minimize the identified gaps in regular screening for Latinas who have low health literacy.

Italian retail gasoline activities: inadequate distribution network

International Nuclear Information System (INIS)

Verde, Stefano

2005-01-01

It is common belief that competition in the Italian retail gasoline activities is hindered by oil companies' collusive behaviour. However, when developing a broader analysis of the sector, low efficiency and scarce competition could results as the consequences coming from an inadequate distribution network and from the recognition of international markets and focal point [it

Evaluation of materials and design modifications for aircraft brakes

Science.gov (United States)

Ho, T. L.; Kennedy, F. E.; Peterson, M. B.

1975-01-01

A test program is described which was carried out to evaluate several proposed design modifications and several high-temperature friction materials for use in aircraft disk brakes. The evaluation program was carried out on a specially built test apparatus utilizing a disk brake and wheel half from a small het aircraft. The apparatus enabled control of brake pressure, velocity, and braking time. Tests were run under both constant and variable velocity conditions and covered a kinetic energy range similar to that encountered in aircraft brake service. The results of the design evaluation program showed that some improvement in brake performance can be realized by making design changes in the components of the brake containing friction material. The materials evaluation showed that two friction materials show potential for use in aircraft disk brakes. One of the materials is a nickel-based sintered composite, while the other is a molybdenum-based material. Both materials show much lower wear rates than conventional copper-based materials and are better able to withstand the high temperatures encountered during braking. Additional materials improvement is necessary since both materials show a significant negative slope of the friction-velocity curve at low velocities.

Translating material and design space

DEFF Research Database (Denmark)

Tamke, Martin; Ramsgaard Thomsen, Mette; Joseffson, Kristoffer

2009-01-01

This paper shares findings from the project DevA (Developable surfaces in Architecture), a research by design based project developed a collaboration between academic and industry partners. The project aims to investigate the use of curved sheet material in architecture using hybridised 3D...

Materials for Nuclear Plants From Safe Design to Residual Life Assessments

CERN Document Server

Hoffelner, Wolfgang

2013-01-01

The clamor for non-carbon dioxide emitting energy production has directly  impacted on the development of nuclear energy. As new nuclear plants are built, plans and designs are continually being developed to manage the range of challenging requirement and problems that nuclear plants face especially when managing the greatly increased operating temperatures, irradiation doses and extended design life spans. Materials for Nuclear Plants: From Safe Design to Residual Life Assessments  provides a comprehensive treatment of the structural materials for nuclear power plants with emphasis on advanced design concepts.   Materials for Nuclear Plants: From Safe Design to Residual Life Assessments approaches structural materials with a systemic approach. Important components and materials currently in use as well as those which can be considered in future designs are detailed, whilst the damage mechanisms responsible for plant ageing are discussed and explained. Methodologies for materials characterization, material...

Battery designs with high capacity anode materials and cathode materials

Energy Technology Data Exchange (ETDEWEB)

Masarapu, Charan; Anguchamy, Yogesh Kumar; Han, Yongbong; Deng, Haixia; Kumar, Sujeet; Lopez, Herman A.

2017-10-03

Improved high energy capacity designs for lithium ion batteries are described that take advantage of the properties of high specific capacity anode active compositions and high specific capacity cathode active compositions. In particular, specific electrode designs provide for achieving very high energy densities. Furthermore, the complex behavior of the active materials is used advantageously in a radical electrode balancing design that significantly reduced wasted electrode capacity in either electrode when cycling under realistic conditions of moderate to high discharge rates and/or over a reduced depth of discharge.

Computer aided materials design; Keisanki zairyo sekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The questionnaire survey on the computer aided materials design (CAMD), and the survey of current domestic and overseas software concerned were carried out to clarify developmental issues. The current elementary technology of CAMD was also surveyed to study its several problems caused with a progress of material design technology due to drastic diffusion of CAMD. This project aims at establishment of a new demanded software, computer chemistry, focusing attention on functional materials such as catalyst, polymer and non-linear electronic materials. Microscopic simulation technology was mainly surveyed in fiscal 1996. Although some fruitful results have been obtained in the fields of medical and agricultural chemicals, organic compounds, proteins, catalysts and electronic materials, such some problems are pointed out as `CAMD cannot handle an actual size of the target system` and `commercially available software are very expensive.` Reliable tool development as elementary technology, and the verification of its applications are thus required. Meso-dynamics, polymers, surface reaction and integrated technological environment attract users` attention. 27 refs., 16 figs., 2 tabs.

High-throughput theoretical design of lithium battery materials

International Nuclear Information System (INIS)

Ling Shi-Gang; Gao Jian; Xiao Rui-Juan; Chen Li-Quan

2016-01-01

The rapid evolution of high-throughput theoretical design schemes to discover new lithium battery materials is reviewed, including high-capacity cathodes, low-strain cathodes, anodes, solid state electrolytes, and electrolyte additives. With the development of efficient theoretical methods and inexpensive computers, high-throughput theoretical calculations have played an increasingly important role in the discovery of new materials. With the help of automatic simulation flow, many types of materials can be screened, optimized and designed from a structural database according to specific search criteria. In advanced cell technology, new materials for next generation lithium batteries are of great significance to achieve performance, and some representative criteria are: higher energy density, better safety, and faster charge/discharge speed. (topical review)

Material selection for design, manufacturing and application

International Nuclear Information System (INIS)

Zaid, A.I.O.

2011-01-01

Developing a new engineering material product or changing an existing one requires new design selecting material and choosing appropriate and economical manufacturing processes. These three main factors play a great role on the performance of the product in service. These items are independent and should not be performed in isolation from each other. With the great advancement of technology in the last decade and with the greater number of engineering materials which are now available, together with the increasing pressure to produce more economic and get reliable products an integrated approach which considers design, material selection and the appropriate manufacturing process makes it easier to achieve the optimum product that combines the functional requirements with the reliability at competitive cost. These diverse activities or items are interdependent; therefore should not be considered in isolation from each other, for example, it is not sufficient that design of the product should satisfy the technical, safety and legal requirements, it must also be possible to be manufactured economically and to be sold at a competitive price and easily disposed at the end of its working life cycle. In this paper, the interaction of these items together in order to arrive to the optimum solution for a particular application are given and discussed. (author)

Designing Teaching Materials for Learning Problem Solving in Technology Education

NARCIS (Netherlands)

Doornekamp, B.G.

In the process of designing teaching materials for learning problem solving in technology education, domain-specific design specifications are considered important elements to raise learning outcomes with these materials. Two domain-specific design specifications were drawn up using a four-step

Photovoltaic module encapsulation design and materials selection, volume 1

Science.gov (United States)

Cuddihy, E.; Carroll, W.; Coulbert, C.; Gupta, A.; Liang, R. H.

1982-01-01

Encapsulation material system requirements, material selection criteria, and the status and properties of encapsulation materials and processes available are presented. Technical and economic goals established for photovoltaic modules and encapsulation systems and their status are described. Available encapsulation technology and data are presented to facilitate design and material selection for silicon flat plate photovoltaic modules, using the best materials available and processes optimized for specific power applications and geographic sites. The operational and environmental loads that encapsulation system functional requirements and candidate design concepts and materials that are identified to have the best potential to meet the cost and performance goals for the flat plate solar array project are described. Available data on encapsulant material properties, fabrication processing, and module life and durability characteristics are presented.

European DEMO design strategy and consequences for materials

Science.gov (United States)

Federici, G.; Biel, W.; Gilbert, M. R.; Kemp, R.; Taylor, N.; Wenninger, R.

2017-09-01

Demonstrating the production of net electricity and operating with a closed fuel-cycle remain unarguably the crucial steps towards the exploitation of fusion power. These are the aims of a demonstration fusion reactor (DEMO) proposed to be built after ITER. This paper briefly describes the DEMO design options that are being considered in Europe for the current conceptual design studies as part of the Roadmap to Fusion Electricity Horizon 2020. These are not intended to represent fixed and exclusive design choices but rather ‘proxies’ of possible plant design options to be used to identify generic design/material issues that need to be resolved in future fusion reactor systems. The materials nuclear design requirements and the effects of radiation damage are briefly analysed with emphasis on a pulsed ‘low extrapolation’ system, which is being used for the initial design integration studies, based as far as possible on mature technologies and reliable regimes of operation (to be extrapolated from the ITER experience), and on the use of materials suitable for the expected level of neutron fluence. The main technical issues arising from the plasma and nuclear loads and the effects of radiation damage particularly on the structural and heat sink materials of the vessel and in-vessel components are critically discussed. The need to establish realistic target performance and a development schedule for near-term electricity production tends to favour more conservative technology choices. The readiness of the technical (physics and technology) assumptions that are being made is expected to be an important factor for the selection of the technical features of the device.

On strength design using free material subjected to multiple load cases

DEFF Research Database (Denmark)

Pedersen, Pauli; Pedersen, Niels Leergaard

2013-01-01

Multiple load cases and the consideration of strength is a reality that most structural designs are exposed to. Improved possibility to produce specific materials, say by fiber lay-up, put focus on research on free material optimization. A formulation for such design problems together with a prac......Multiple load cases and the consideration of strength is a reality that most structural designs are exposed to. Improved possibility to produce specific materials, say by fiber lay-up, put focus on research on free material optimization. A formulation for such design problems together...... with a practical recursive design procedure is presented and illustrated with examples. The presented finite element analysis involve many elements as well as many load cases. Separating the local amount of material from a description with unit trace for the local anisotropy, gives the free materials formulation...

Functional design criteria for the Hazardous Materials Management and Emergency Response (HAMMER) Training Center. Revision 1

International Nuclear Information System (INIS)

Sato, P.K.

1995-01-01

Within the United States, there are few hands-on training centers capable of providing integrated technical training within a practical application environment. Currently, there are no training facilities that offer both radioactive and chemical hazardous response training. There are no hands-on training centers that provide training for both hazardous material operations and emergency response that also operate as a partnership between organized labor, state agencies, tribes, and local emergency responders within the US Department of Energy (DOE) complex. Available facilities appear grossly inadequate for training the thousands of people at Hanford, and throughout the Pacific Northwest, who are required to qualify under nationally-mandated requirements. It is estimated that 4,000 workers at the Hanford Site alone need hands-on training. Throughout the Pacific Northwest, the potential target audience would be over 30,000 public sector emergency response personnel, as well as another 10,000 clean-up workers represented by organized labor. The HAMMER Training Center will be an interagency-sponsored training center. It will be designed, built, and operated to ensure that clean-up workers, fire fighters, and public sector management and emergency response personnel are trained to handle accidental spills of hazardous materials. Training will cover wastes at clean-up sites, and in jurisdictions along the transportation corridors, to effectively protect human life, property, and the environment

CubeSat Material Limits for Design for Demise

Science.gov (United States)

Kelley, R. L.; Jarkey, D. R.

2014-01-01

The CubeSat form factor of nano-satellite (a satellite with a mass between one and ten kilograms) has grown in popularity due to their ease of construction and low development and launch costs. In particular, their use as student led payload design projects has increased due to the growing number of launch opportunities. CubeSats are often deployed as secondary or tertiary payloads on most US launch vehicles or they may be deployed from the ISS. The focus of this study will be on CubeSats launched from the ISS. From a space safety standpoint, the development and deployment processes for CubeSats differ significantly from that of most satellites. For large satellites, extensive design reviews and documentation are completed, including assessing requirements associated with re-entry survivability. Typical CubeSat missions selected for ISS deployment have a less rigorous review process that may not evaluate aspects beyond overall design feasibility. CubeSat design teams often do not have the resources to ensure their design is compliant with re-entry risk requirements. A study was conducted to examine methods to easily identify the maximum amount of a given material that can be used in the construction of a CubeSats without posing harm to persons on the ground. The results demonstrate that there is not a general equation or relationship that can be used for all materials; instead a limiting value must be defined for each unique material. In addition, the specific limits found for a number of generic materials that have been previously used as benchmarking materials for re-entry survivability analysis tool comparison will be discussed.

Design of advanced materials for linear and nonlinear dynamics

DEFF Research Database (Denmark)

Frandsen, Niels Morten Marslev

to reveal the fundamental dynamic characteristics and thus the relevant design parameters.The thesis is built around the characterization of two one-dimensional, periodic material systems. The first is a nonlinear mass-spring chain with periodically varying material properties, representing a simple......The primary catalyst of this PhD project has been an ambition to design advanced materials and structural systems including, and possibly even exploiting, nonlinear phenomena such as nonlinear modal interaction leading to energy conversion between modes. An important prerequisite for efficient...... but general model of inhomogeneous structural materials with nonlinear material characteristics. The second material system is an “engineered” material in the sense that a classical structural element, a linear elastic and homogeneous rod, is “enhanced” by applying a mechanism on its surface, amplifying...

Advanced composite structures. [metal matrix composites - structural design criteria for spacecraft construction materials

Science.gov (United States)

1974-01-01

A monograph is presented which establishes structural design criteria and recommends practices to ensure the design of sound composite structures, including composite-reinforced metal structures. (It does not discuss design criteria for fiber-glass composites and such advanced composite materials as beryllium wire or sapphire whiskers in a matrix material.) Although the criteria were developed for aircraft applications, they are general enough to be applicable to space vehicles and missiles as well. The monograph covers four broad areas: (1) materials, (2) design, (3) fracture control, and (4) design verification. The materials portion deals with such subjects as material system design, material design levels, and material characterization. The design portion includes panel, shell, and joint design, applied loads, internal loads, design factors, reliability, and maintainability. Fracture control includes such items as stress concentrations, service-life philosophy, and the management plan for control of fracture-related aspects of structural design using composite materials. Design verification discusses ways to prove flightworthiness.

Critical plasma-materials issues for fusion reactor designs

International Nuclear Information System (INIS)

Wilson, K.L.; Bauer, W.

1983-01-01

Plasma-materials interactions are a dominant driving force in the design of fusion power reactors. This paper presents a summary of plasma-materials interactions research. Emphasis is placed on critical aspects related to reactor design. Particular issues to be addressed are plasma edge characterization, hydrogen recycle, impurity introduction, and coating development. Typical wall fluxes in operating magnetically confined devices are summarized. Recent calculations of tritium inventory and first wall permeation, based on laboratory measurements of hydrogen recycling, are given for various reactor operating scenarios. Impurity introduction/wall erosion mechanisms considered include sputtering, chemical erosion, and evaporation (melting). Finally, the advanced material development for in-vessel components is discussed. (author)

Materials design for electrocatalytic carbon capture

Directory of Open Access Journals (Sweden)

Xin Tan

2016-05-01

Full Text Available We discuss our philosophy for implementation of the Materials Genome Initiative through an integrated materials design strategy, exemplified here in the context of electrocatalytic capture and separation of CO2 gas. We identify for a group of 1:1 X–N graphene analogue materials that electro-responsive switchable CO2 binding behavior correlates with a change in the preferred binding site from N to the adjacent X atom as negative charge is introduced into the system. A reconsideration of conductive N-doped graphene yields the discovery that the N-dopant is able to induce electrocatalytic binding of multiple CO2 molecules at the adjacent carbon sites.

Materials challenges supporting new sodium fast reactor designs

International Nuclear Information System (INIS)

Gelineau, O.; Goff, S. Dubiez-le; Dubuisson, Ph.; Dalle, F.; Blat, M.

2009-01-01

Sodium Fast Reactor is considered in France as the most mature technology of the different Generation IV systems. In the short-term the designing work is focused on the identification of the potential tracks to improve competitiveness, safety, efficiency and to reduce cost. In that frame the materials have a key role to play. This paper is focused on the new materials envisaged and on the Research and Development program launched in France by Areva NP, CEA and EDF in order to sustain the innovative design options: ferritic steels as candidates for exchangers, steam generators and possibly sodium circuits, optimization of materials and fabrication processes to improve safety and risk management, extension of material databases to take into account the 60 years life duration including irradiation and ageing effect. (author)

DESIGNING ENGLISH LEARNING MATERIALS TO FOSTER CHILDREN‟S CREATIVITY

Directory of Open Access Journals (Sweden)

C. Murni Wahyanti

2017-04-01

Full Text Available Learning materials form an important part of English teaching-learning processes in Elementary schools. In many cases, teachers and students rely on the learning materials available and the materials dictate teachers‘ strategies. Despite the availability of commercially produced materials, it is considered necessary for teachers to construct or adapt learning materials. Teachers know better about their students‘ ability, needs and interests. In addition, the materials can be more contextual. Good materials should foster children‘s creative thinking since creativity is one of the important skills children need to develop. Features of creativity involve using imagination, generating ideas and questions, experimenting with alternatives, being original and making judgment. This presentation will focus on how to develop learning materials that can foster children‘s creativity. It will discuss about why teachers need to design their own materials, principles for designing effective English learning materials, the concepts and components of creativity and the importance of creativity in language learning. Examples of how to apply features of creativity in the English learning materials for children will be provided.

Local Material as a Character of Contemporary Interior Design in Indonesia

Science.gov (United States)

Susanto, Dalhar; Puti Angelia, Dini; Ningsih, Tria Amalia

2017-12-01

Excellent design needs to fulfill universal requirements (utility, aesthetic, ergonomic, durability, and safe). Besides of all the requirements, an excellent design has to be shown its distinctiveness, uniqueness, and identity. To create an excellent design, we can use one of locality approach, it means local material utilization. From time to time, the material is linking each other in unity with environment context, human, knowledge, culture, social, economy, user needs and material availability. The aspects are the important part to get the reflective identity and local values in architecture and interior design work in Indonesia. It can be proofed by some of the architecture and interior work precedent, like traditional or vernacular in Nusantara or contemporary interior design work from Indonesian designer who has recognized to promote the locality value. However interior design works in Indonesia cannot be shown the characteristic of Indonesia identity and locality currently, it is different than another country work, like Japan, Italy, or Scandinavia. Interior design work from these countries can be easily known with accentuating of characteristic their places, such as material, color, detail, or geometry pattern in the product that has been produced. Meanwhile, some of the region in Indonesia are tropical climate and brought about much of local material and it has potential to make a unique work which has the local identity. This paper will discuss the result of a searching potential of local material usefulness as interior design identity in Indonesia. This research is done by typology method, which means discover the presence of some of the architecture elements appears to be related material. The elements are the pattern, color, craftsmanship, building element, object, and type of material in some of the contemporary interior design work in Indonesia were considered superior and capable of lifting elements recognized locality.

A Strategy for Material-specific e-Textile Interaction Design

DEFF Research Database (Denmark)

Gowrishankar, Ramyah; Bredies, Katharina; Ylirisku, Salu

2017-01-01

The interaction design of e-Textile products are often characterized by conventions adopted from electronic devices rather than developing interactions that can be specific to e-Textiles. We argue that textile materials feature a vast potential for the design of novel digital interactions....... Especially the shape-reformation capabilities of textiles may inform the design of expressive and aesthetically rewarding applications. In this chapter, we propose ways in which the textileness of e-Textiles can be better harnessed. We outline an e-Textile Interaction Design strategy that is based...... on defining the material-specificity of e-Textiles as its ability to deform in ways that match the expectations we have of textile materials. It embraces an open-ended exploration of textile-related interactions (for e.g. stretching, folding, turning-inside-out etc.) and their potential for electronic...

Cognitive Attributes of Adequate and Inadequate Responders to Reading Intervention in Middle School

Science.gov (United States)

Miciak, Jeremy; Stuebing, Karla K.; Vaughn, Sharon; Roberts, Greg; Barth, Amy E.; Fletcher, Jack M.

2014-01-01

No studies have investigated the cognitive attributes of middle school students who are adequate and inadequate responders to Tier 2 reading intervention. We compared students in Grades 6 and 7 representing groups of adequate responders (n = 77) and inadequate responders who fell below criteria in (a) comprehension (n = 54); (b) fluency (n = 45);…

The innovative application studty on eco-packaging design and materials

OpenAIRE

Cui Yong Min; Ren Xin Guang

2016-01-01

The paper solves the increasingly deteriorate environmental problems by positively exploring how to utilize and develop eco-packaging design reasonably. The paper explores an effective method that combines eco-packaging and environmental protection materials, hoping to define the sustainable development road of packaging design. The paper is centered on the design application of eco-packaging and environmental protection materials, applies and analyzes the method to obtain innovative design r...

Computational Materials Program for Alloy Design

Science.gov (United States)

Bozzolo, Guillermo

2005-01-01

The research program sponsored by this grant, "Computational Materials Program for Alloy Design", covers a period of time of enormous change in the emerging field of computational materials science. The computational materials program started with the development of the BFS method for alloys, a quantum approximate method for atomistic analysis of alloys specifically tailored to effectively deal with the current challenges in the area of atomistic modeling and to support modern experimental programs. During the grant period, the program benefited from steady growth which, as detailed below, far exceeds its original set of goals and objectives. Not surprisingly, by the end of this grant, the methodology and the computational materials program became an established force in the materials communitiy, with substantial impact in several areas. Major achievements during the duration of the grant include the completion of a Level 1 Milestone for the HITEMP program at NASA Glenn, consisting of the planning, development and organization of an international conference held at the Ohio Aerospace Institute in August of 2002, finalizing a period of rapid insertion of the methodology in the research community worlwide. The conference, attended by citizens of 17 countries representing various fields of the research community, resulted in a special issue of the leading journal in the area of applied surface science. Another element of the Level 1 Milestone was the presentation of the first version of the Alloy Design Workbench software package, currently known as "adwTools". This software package constitutes the first PC-based piece of software for atomistic simulations for both solid alloys and surfaces in the market.Dissemination of results and insertion in the materials community worldwide was a primary focus during this period. As a result, the P.I. was responsible for presenting 37 contributed talks, 19 invited talks, and publishing 71 articles in peer-reviewed journals, as

LUTE primary mirror materials and design study report

Science.gov (United States)

Ruthven, Greg

1993-02-01

The major objective of the Lunar Ultraviolet Telescope Experiment (LUTE) Primary Mirror Materials and Design Study is to investigate the feasibility of the LUTE telescope primary mirror. A systematic approach to accomplish this key goal was taken by first understanding the optical, thermal, and structural requirements and then deriving the critical primary mirror-level requirements for ground testing, launch, and lunar operations. After summarizing the results in those requirements which drove the selection of material and the design for the primary mirror are discussed. Most important of these are the optical design which was assumed to be the MSFC baseline (i.e. 3 mirror optical system), telescope wavefront error (WFE) allocations, the telescope weight budget, and the LUTE operational temperature ranges. Mechanical load levels, reflectance and microroughness issues, and options for the LUTE metering structure were discussed and an outline for the LUTE telescope sub-system design specification was initiated. The primary mirror analysis and results are presented. The six material substrate candidates are discussed and four distinct mirror geometries which are considered are shown. With these materials and configurations together with varying the location of the mirror support points, a total of 42 possible primary mirror designs resulted. The polishability of each substrate candidate was investigated and a usage history of 0.5 meter and larger precision cryogenic mirrors (the operational low end LUTE temperature of 60 K is the reason we feel a survey of cryogenic mirrors is appropriate) that were flown or tested are presented.

Granular Materials and Risks In ISRU

Science.gov (United States)

Behringer, Robert P.; Wilkinson, R. Allen

2004-01-01

Working with soil, sand, powders, ores, cement and sintered bricks, excavating, grading construction sites, driving off-road, transporting granules in chutes and pipes, sifting gravel, separating solids from gases, and using hoppers are so routine that it seems straightforward to execute these operations on the Moon and Mars as we do on Earth. We discuss how little these processes are understood and point out the nature of trial-and-error practices that are used in today's massive over-design. Nevertheless, such designs have a high failure rate. Implementation and extensive incremental scaling up of industrial processes are routine because of the inadequate predictive tools for design. We present a number of pragmatic scenarios where granular materials play a role, the risks involved, what some of the basic issues are, and what understanding is needed to greatly reduce the risks. This talk will focus on a particular class of granular flow issues, those that pertain to dense materials, their physics, and the failure problems associated with them. In particular, key issues where basic predictability is lacking include stability of soils for the support of vehicles and facilities, ability to control the flow of dense materials (jamming and flooding/unjamming at the wrong time), the ability to predict stress profiles (hence create reliable designs) for containers such as bunkers or silos. In particular, stress fluctuations, which are not accounted for in standard granular design models, can be very large as granular materials flows, and one result is frequent catastrophic failure of granular devices.

The materials challenge for LFR core design

International Nuclear Information System (INIS)

Grasso, Giacomo; Agostini, Pietro

2013-01-01

LFR share the main issues of all Fast Reactors, while presenting specific issues due to the use of lead as coolant. A number of constraints impairs the design of a LFR core, possibly resulting in a viability domain not exploitable for producing electricity in an efficient (hence economic) way. In particular, the most restrictive issues to be faced pend on the cladding. The selection of proper cladding materials provides the solution for the issues impairing the resistance of the cladding against stresses and irradiation effects. On the other hand, the protection of the cladding requires surface protections like oxide scales (passivation) or adherent layers (coating). Oxide scales seem not sufficient for a stable and effective protection of the base material. The application of adherent layers seems the only promising solution for protecting the cladding against corrosion. For the short term (i.e.: ALFRED), advanced 15/15Ti with coating is the reference solution for the cladding, allowing a core design complying with all the design constraints and goals. The candidate coatings are already being tested under irradiation to proceed towards qualification. In parallel, new base materials and/or coatings are presently under investigation. For the long term (i.e.: ELFR), the availability of such advanced materials/coatings might allow the extension of the viability domain towards higher and broader ranges (temperature, dpa, etc.), extending the fields of applications of LFRs and resulting in higher performances

Timber Curtain: Designing with material capabilities

DEFF Research Database (Denmark)

Lahmy, Maya; Larsen, Niels Martin

2015-01-01

of the generative phase to fabrication of the artefact. Brought together by various conceptual and structural elements the Timber Curtain forms a 4.5 x 2.5 x 0.5 m construct of assembled wood components, digitally crafted through advanced production techniques. Concerned with materiality and processing of the wood......Timber Curtain explores relations between digital precision and material indeterminacy. It is an installation engaging spatially through its presence as a 1:1 architectural component as well as it is exploring novel technologies in the architectural design process from the very beginning...... an associative digital model that could gather and compute in put from material behaviour and out put manufacturing data was scripted. This method enables material capacity to be pushed to the limit of its performance allowing novel sensuous and structural qualities to emerge. The method is developed with use...

IBARAKI Materials Design Diffractometer for J-PARC

International Nuclear Information System (INIS)

Ishigaki, Toru; Harjo, Stefanus; Yonemura, Masao; Kamiyama, Takashi; Aizawa, Kazuya; Oikawa, Kenichi; Sakuma, Takashi; Morii, Yukio; Arai, Masatoshi; Ebata, Kazuhiro; Takano, Yoshiki; Kasao, Takuro

2006-01-01

Ibaraki prefecture, the local government of the area for J-PARC site, has decided to build a versatile powder diffractometer (IBARAKI Materials Design Diffractometer) to promote industrial applications for neutron beams in J-PARC. This diffractometer is designed to be a high throughput one enabling materials scientists to use it like the chemical analytical instruments in their material development processes. It covers in d range 0.18< d(A)<5 with Δd/d=0.16% at the high-resolution scattering detector bank, and covers 5< d(A)<800 with gradually changing resolution. Typical measuring time to obtain a 'Rietveld-quality' data is several minutes for the sample size of laboratory X-ray diffractometer. To promote industrial application, a utilization system for this diffractometer is required. We will establish a support system for both academic and industrial users who are willing to use neutron but have not been familiar with neutron diffraction

Interrelationship betwen material strength and component design under elevated temperature for FBR

International Nuclear Information System (INIS)

Nakagawa, Y.

Structural design under elevated temperature for fast breeder reactor plant is very troublesome compared to that of for lower temperature. This difficulty can be mainly discussed from two different stand points. One is design and design code, another is material strength. Components in FBR are operated under creep regime and time dependent creep behaviour should be elevated properly. This means the number and combinations of design code and material strength are significantly large and makes these systems very complicated. Material selection is, in no words, not an easy job. This should be done by not only material development but also component design stand point. With valuable experience of construction and research on FBR, a lot of information on component design and material behaviour is available. And it is a time to choose the ''best material'' from the entire stand points of component construction. (author)

Cultivating Design Thinking in Students through Material Inquiry

Science.gov (United States)

Renard, Helene

2014-01-01

Design thinking is a way of understanding and engaging with the world that has received much attention in academic and business circles in recent years. This article examines a hands-on learning model as a vehicle for developing design thinking capacity in students. An overview of design thinking grounds the discussion of the material-based…

A Novel Design Framework for Structures/Materials with Enhanced Mechanical Performance

Directory of Open Access Journals (Sweden)

Jie Liu

2018-04-01

Full Text Available Structure/material requires simultaneous consideration of both its design and manufacturing processes to dramatically enhance its manufacturability, assembly and maintainability. In this work, a novel design framework for structural/material with a desired mechanical performance and compelling topological design properties achieved using origami techniques is presented. The framework comprises four procedures, including topological design, unfold, reduction manufacturing, and fold. The topological design method, i.e., the solid isotropic material penalization (SIMP method, serves to optimize the structure in order to achieve the preferred mechanical characteristics, and the origami technique is exploited to allow the structure to be rapidly and easily fabricated. Topological design and unfold procedures can be conveniently completed in a computer; then, reduction manufacturing, i.e., cutting, is performed to remove materials from the unfolded flat plate; the final structure is obtained by folding out the plate from the previous procedure. A series of cantilevers, consisting of origami parallel creases and Miura-ori (usually regarded as a metamaterial and made of paperboard, are designed with the least weight and the required stiffness by using the proposed framework. The findings here furnish an alternative design framework for engineering structures that could be better than the 3D-printing technique, especially for large structures made of thin metal materials.

A Novel Design Framework for Structures/Materials with Enhanced Mechanical Performance

Science.gov (United States)

Liu, Jie; Fan, Xiaonan; Wen, Guilin; Qing, Qixiang; Wang, Hongxin; Zhao, Gang

2018-01-01

Structure/material requires simultaneous consideration of both its design and manufacturing processes to dramatically enhance its manufacturability, assembly and maintainability. In this work, a novel design framework for structural/material with a desired mechanical performance and compelling topological design properties achieved using origami techniques is presented. The framework comprises four procedures, including topological design, unfold, reduction manufacturing, and fold. The topological design method, i.e., the solid isotropic material penalization (SIMP) method, serves to optimize the structure in order to achieve the preferred mechanical characteristics, and the origami technique is exploited to allow the structure to be rapidly and easily fabricated. Topological design and unfold procedures can be conveniently completed in a computer; then, reduction manufacturing, i.e., cutting, is performed to remove materials from the unfolded flat plate; the final structure is obtained by folding out the plate from the previous procedure. A series of cantilevers, consisting of origami parallel creases and Miura-ori (usually regarded as a metamaterial) and made of paperboard, are designed with the least weight and the required stiffness by using the proposed framework. The findings here furnish an alternative design framework for engineering structures that could be better than the 3D-printing technique, especially for large structures made of thin metal materials. PMID:29642555

A Novel Design Framework for Structures/Materials with Enhanced Mechanical Performance.

Science.gov (United States)

Liu, Jie; Fan, Xiaonan; Wen, Guilin; Qing, Qixiang; Wang, Hongxin; Zhao, Gang

2018-04-09

Abstract : Structure/material requires simultaneous consideration of both its design and manufacturing processes to dramatically enhance its manufacturability, assembly and maintainability. In this work, a novel design framework for structural/material with a desired mechanical performance and compelling topological design properties achieved using origami techniques is presented. The framework comprises four procedures, including topological design, unfold, reduction manufacturing, and fold. The topological design method, i.e., the solid isotropic material penalization (SIMP) method, serves to optimize the structure in order to achieve the preferred mechanical characteristics, and the origami technique is exploited to allow the structure to be rapidly and easily fabricated. Topological design and unfold procedures can be conveniently completed in a computer; then, reduction manufacturing, i.e., cutting, is performed to remove materials from the unfolded flat plate; the final structure is obtained by folding out the plate from the previous procedure. A series of cantilevers, consisting of origami parallel creases and Miura-ori (usually regarded as a metamaterial) and made of paperboard, are designed with the least weight and the required stiffness by using the proposed framework. The findings here furnish an alternative design framework for engineering structures that could be better than the 3D-printing technique, especially for large structures made of thin metal materials.

Design and Fabrication of Aerospace-Grade Digital Composite Materials

Data.gov (United States)

National Aeronautics and Space Administration — This project aims to advance design rules and fabrication approaches to create aerospace-grade structures from digital composite materials. Digital materials are...

Exploring Socio-material Orderings in Ethnography of Architectural Design

DEFF Research Database (Denmark)

Lotz, Katrine; Stang Våland, Marianne

How can the socio-material assemblages involved in contemporary ‘doings of architecture’ be identified and studied? The paper discusses recent transformations within architectural design practice and the extended network of local actors and technologies mobilized in contemporary building...... construction. Interested in examining how the current requirements in the field are – and can be - handled in architectural production, we aim to contribute to the ongoing development of ethnography of Architectural Design (Yaneva 2008, 2009, 2012). In our research, we focus on recent requirements...... in contemporary architectural design. We attempt to follow the actors in detail through their socio-material involvements and ‘architectural inventions’ such as visualized motives of space, materials, atmospheres, buildingparts and -components, and to explore how relations continuously tie and untie as a means...

Revolutionising catenary design: the use of new materials

NARCIS (Netherlands)

Smulders, H.W.M.; Wouters, P.A.A.F.; Minkman, J.A.; Waes, van J.B.M.

2011-01-01

Traditionally materials used for catenary support structures are steel, concrete or even wood, in combination with the use of insulators. The development of new materials such as Fibre Reinforced Plastics (FRP) makes a new revolutionary design possible. The use of FRP is expanding rapidly at the

Structural optimization for materially informed design to robotic production processes

NARCIS (Netherlands)

Bier, H.H.; Mostafavi, S.

2015-01-01

Hyperbody’s materially informed Design-to-Robotic-Production (D2RP) processes for additive and subtractive manufacturing aim to achieve performative porosity in architecture at various scales. An extended series of D2RP experiments aiming to produce prototypes at 1:1 scale wherein design materiality

Designing Web-Based Educative Curriculum Materials for the Social Studies

Science.gov (United States)

Callahan, Cory; Saye, John; Brush, Thomas

2013-01-01

This paper reports on a design experiment of web-based curriculum materials explicitly created to help social studies teachers develop their professional teaching knowledge. Web-based social studies curriculum reform efforts, human-centered interface design, and investigations into educative curriculum materials are reviewed, as well as…

Design of Molecular Materials: Supramolecular Engineering

Science.gov (United States)

Simon, Jacques; Bassoul, Pierre

2001-02-01

This timely and fascinating book is destined to be recognised as THE book on supramolecular engineering protocols. It covers this sometimes difficult subject in an approachable form, gathering together information from many sources. Supramolecular chemistry, which links organic chemistry to materials science, is one of the fastest growth areas of chemistry research. This book creates a correlation between the structure of single molecules and the physical and chemical properties of the resulting materials. By making systematic changes to the component molecules, the resulting solid can be engineered for optimum performance. There is a clearly written development from synthesis of designer molecules to properties of solids and further on to devices and complex materials systems, providing guidelines for mastering the organisation of these systems. Topics covered include: Systemic chemistry Molecular assemblies Notions of symmetry Supramolecular engineering Principe de Curie Organisation in molecular media Molecular semiconductors Industrial applications of molecular materials This superb book will be invaluable to researchers in the field of supramolecular materials and also to students and teachers of the subject.

Designing with Matter: From Programmable Materials to Processual Things

Directory of Open Access Journals (Sweden)

Agustina Andreoletti

2016-11-01

Full Text Available This paper explores the potential of active matter, from a practical exploration of the concept to a theoretical discussion based on the material findings. It begins by addressing the ideas of materiality and material performance through the project “Chrysalis Gemini” and then provides an overview of the notion of programmability.To this end, we move to the description and analysis of programming, focusing on its relationship with hardware, software and material. In particular, we address the idea of programmable matter, and we introduce the term processuality. We consider the importance of adaptability, analysing the experience of humans, their interaction with the environment, with artefacts and with material within a design context.In this manner this study seeks to highlight how contextualisation and interconnected processes become relevant as a design argument. This is achieved by presenting the relational potential of processual material and things and their ongoing transformation. 

Factors associated with inadequate work ability among women in the clothing industry.

Science.gov (United States)

Augusto, Viviane Gontijo; Sampaio, Rosana Ferreira; Ferreira, Fabiane Ribeiro; Kirkwood, Renata Noce; César, Cibele Comini

2015-01-01

Work ability depends on a balance between individual resources and work demands. This study evaluated factors that are associated with inadequate work ability among workers in the clothing industry. We conducted a cross-sectional observational study of 306 workers in 40 small and medium-sized enterprises. We assessed work ability, individual resources, physical and psychosocial demands, and aspects of life outside work using a binary logistic regression model with hierarchical data entry. The mean work ability was 42.5 (SD=3.5); when adjusted for age, only 11% of the workers showed inadequate work ability. The final model revealed that smoking, high isometric physical load, and poor physical environmental conditions were the most significant predictors of inadequate work ability. Good working conditions and worker education must be implemented to eliminate factors that can be changed and that have a negative impact on work ability. These initiatives include anti-smoking measures, improved postures at work, and better physical environmental conditions.

Bremsstrahlung convertors: materials design and development

International Nuclear Information System (INIS)

Allred, R.E.

1976-03-01

An improved bremsstrahlung convertor for use at high electron beam energies was developed. The convertor consists of three main components: (1) conversion foil; (2) electron scavenger; and (3) impulse shield. Structural failures of the impulse shield were experimentally determined to be caused by shock wave interactions. Convertor materials and design modifications were aimed at attenuation of the magnitude of the shock and maximization of energy absorption by the convertor materials. Techniques proven successful included the introduction of porosity into electron scavenger and impulse shield materials, the use of a standoff between the conversion foil and the electron scavenger, the insertion of a gap between the scavenger and impulse shield, and the use of advanced composite materials for the impulse shield. These modifications have increased the convertor operating range from 4 cal/gm Au to over 8 cal/gm Au. Kevlar 49 reinforced-resin composites have proven to have the best combination of strength, stiffness, toughness, and x-ray transport properties for use as bremmstrahlung convertor impulse shields

The reactor accident in Fukushima Daiichi. The consequence of design deficiencies and inadequate safety engineering; Der Reaktorunfall in Fukushima Daiichi. Folge fehlerhafter Auslegung und unzureichender Sicherheitstechnik

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-03-15

The reactor accident in Fukushima Daiichi is discussed in the frame of design deficiencies and inadequate safety engineering. The progress of the accident as consequence of the earthquake and the tsunami is described. The radiological situation for the public is supposed to be blow the dose limit of 20 mSv/year. The WHO and UNSCEAR (United Nations Scientific Committee on the Effects of Atomic radiation) did not observe acute radiation injuries. The Japanese authorities have classified the accident to 7 of the INES scale. The German Atomforum e.V. considers the safety engineering of German NPPs to be superior to the Japanese situation due to higher emergency energy supply, extensive measures to reduce the hydrogen accumulation and mitigating measures for the accident management. German NPPS are considered highly robust as the EU stress tests have shown.

Design of POLCA material control systems

NARCIS (Netherlands)

Riezebos, J.

2010-01-01

POLCA is a material control system designed for make-to-order or engineer-to-order companies. These firms have to cope with a high variety of customised products, and strong pressure to provide short throughput times. POLCA constrains the amount of work in progress on the shop floor in order to

14 CFR 25.613 - Material strength properties and material design values.

Science.gov (United States)

2010-01-01

... statistical basis. (b) Material design values must be chosen to minimize the probability of structural... following probability: (1) Where applied loads are eventually distributed through a single member within an... probability with 95 percent confidence. (2) For redundant structure, in which the failure of individual...

Virtual 3D planning of tracheostomy placement and clinical applicability of 3D cannula design : A three-step study

NARCIS (Netherlands)

de Kleijn, Bertram J; Kraeima, Joep; Wachters, Jasper E; van der Laan, Bernard F A M; Wedman, Jan; Witjes, M J H; Halmos, Gyorgy B

AIM: We aimed to investigate the potential of 3D virtual planning of tracheostomy tube placement and 3D cannula design to prevent tracheostomy complications due to inadequate cannula position. MATERIALS AND METHODS: 3D models of commercially available cannula were positioned in 3D models of the

Evidence Report, Risk of Inadequate Design of Human and Automation/Robotic Integration

Science.gov (United States)

Zumbado, Jennifer Rochlis; Billman, Dorrit; Feary, Mike; Green, Collin

2011-01-01

The success of future exploration missions depends, even more than today, on effective integration of humans and technology (automation and robotics). This will not emerge by chance, but by design. Both crew and ground personnel will need to do more demanding tasks in more difficult conditions, amplifying the costs of poor design and the benefits of good design. This report has looked at the importance of good design and the risks from poor design from several perspectives: 1) If the relevant functions needed for a mission are not identified, then designs of technology and its use by humans are unlikely to be effective: critical functions will be missing and irrelevant functions will mislead or drain attention. 2) If functions are not distributed effectively among the (multiple) participating humans and automation/robotic systems, later design choices can do little to repair this: additional unnecessary coordination work may be introduced, workload may be redistributed to create problems, limited human attentional resources may be wasted, and the capabilities of both humans and technology underused. 3) If the design does not promote accurate understanding of the capabilities of the technology, the operators will not use the technology effectively: the system may be switched off in conditions where it would be effective, or used for tasks or in contexts where its effectiveness may be very limited. 4) If an ineffective interaction design is implemented and put into use, a wide range of problems can ensue. Many involve lack of transparency into the system: operators may be unable or find it very difficult to determine a) the current state and changes of state of the automation or robot, b) the current state and changes in state of the system being controlled or acted on, and c) what actions by human or by system had what effects. 5) If the human interfaces for operation and control of robotic agents are not designed to accommodate the unique points of view and

14 CFR 29.613 - Material strength properties and design values.

Science.gov (United States)

2010-01-01

... Administrator: (1) MIL—HDBK-5, “Metallic Materials and Elements for Flight Vehicle Structure”. (2) MIL—HDBK-17, “Plastics for Flight Vehicles”. (3) ANC-18, “Design of Wood Aircraft Structures”. (4) MIL—HDBK-23... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Material strength properties and design...

14 CFR 27.613 - Material strength properties and design values.

Science.gov (United States)

2010-01-01

... Administrator: (1) MIL-HDBK-5, “Metallic Materials and Elements for Flight Vehicle Structure”. (2) MIL-HDBK-17, “Plastics for Flight Vehicles”. (3) ANC-18, “Design of Wood Aircraft Structures”. (4) MIL-HDBK-23... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Material strength properties and design...

A design methodology for materials control and accounting information systems

International Nuclear Information System (INIS)

Helman, P.; Strittmatter, R.B.

1987-01-01

Modern approaches to nuclear materials safeguards have significantly increased the data processing needs of safeguards information systems. Implementing these approaches will require developing efficient, cost-effective designs. Guided by database design research, we are developing a design methodology for distributed materials control and accounting (MCandA) information systems. The methodology considers four design parameters: network topology, allocation of data to nodes, high-level global processing strategy, and local file structures to optimize system performance. Characteristics of system performance that are optimized are response time for an operation, timeliness of data, validity of data, and reliability. The ultimate goal of the research is to develop a comprehensive computerized design tool specifically tailored to the design of MCandA systems

Soft computing in design and manufacturing of advanced materials

Science.gov (United States)

Cios, Krzysztof J.; Baaklini, George Y; Vary, Alex

1993-01-01

The potential of fuzzy sets and neural networks, often referred to as soft computing, for aiding in all aspects of manufacturing of advanced materials like ceramics is addressed. In design and manufacturing of advanced materials, it is desirable to find which of the many processing variables contribute most to the desired properties of the material. There is also interest in real time quality control of parameters that govern material properties during processing stages. The concepts of fuzzy sets and neural networks are briefly introduced and it is shown how they can be used in the design and manufacturing processes. These two computational methods are alternatives to other methods such as the Taguchi method. The two methods are demonstrated by using data collected at NASA Lewis Research Center. Future research directions are also discussed.

Urban public space materials. Maintenance and design?

Directory of Open Access Journals (Sweden)

Manuel Iglesias Campos

2016-10-01

Full Text Available In this paper, certain aspects related to the conservation of materials commonly used in the design of public spaces are analysed and discussed from a starting point of maintenance definition. The main area of discussion is whether materials selection for pavements and urban furniture, and their placement in the designed space, take into account their maintenance needs. Here the definition of maintenance is the cleaning and repair done by municipal services that is always necessary after construction. From certain examples it can be concluded that, in several cases, the form, the organization and the distribution of the different elements within the public space can cause difficulties for its appropriate conservation, giving rise to alterations and consequently having a negative impact on the durability of this space.

Design of lightweight multi-material automotive bodies using new material performance indices of thin-walled beams for the material selection with crashworthiness consideration

International Nuclear Information System (INIS)

Cui, Xintao; Zhang, Hongwei; Wang, Shuxin; Zhang, Lianhong; Ko, Jeonghan

2011-01-01

Currently, automotive bodies are constructed usually using a single material, e.g. steel or aluminum. Compared to single-material automotive bodies, multi-material automotive bodies allow optimal material selection in each structural component for higher product performance and lower cost. This paper presents novel material performance indices and procedures developed to guide systematic material selection for multi-material automotive bodies. These new indices enable to characterize the crashworthiness performance of complex-shaped thin-walled beams in multi-material automotive bodies according to material types. This paper also illustrates the application of these performance indices and procedures by designing a lightweight multi-material automotive body. These procedures will help to design a lightweight and affordable body favored by the automotive industry, thus to reduce fuel consumption and greenhouse gas emissions.

Topology optimization for design of segmented permanent magnet arrays with ferromagnetic materials

Science.gov (United States)

Lee, Jaewook; Yoon, Minho; Nomura, Tsuyoshi; Dede, Ercan M.

2018-03-01

This paper presents multi-material topology optimization for the co-design of permanent magnet segments and iron material. Specifically, a co-design methodology is proposed to find an optimal border of permanent magnet segments, a pattern of magnetization directions, and an iron shape. A material interpolation scheme is proposed for material property representation among air, permanent magnet, and iron materials. In this scheme, the permanent magnet strength and permeability are controlled by density design variables, and permanent magnet magnetization directions are controlled by angle design variables. In addition, a scheme to penalize intermediate magnetization direction is proposed to achieve segmented permanent magnet arrays with discrete magnetization directions. In this scheme, permanent magnet strength is controlled depending on magnetization direction, and consequently the final permanent magnet design converges into permanent magnet segments having target discrete directions. To validate the effectiveness of the proposed approach, three design examples are provided. The examples include the design of a dipole Halbach cylinder, magnetic system with arbitrarily-shaped cavity, and multi-objective problem resembling a magnetic refrigeration device.

Bioinspiration from fish for smart material design and function

International Nuclear Information System (INIS)

Lauder, G V; Madden, P G A; Tangorra, J L; Anderson, E; Baker, T V

2011-01-01

Fish are a potentially rich source of inspiration for the design of smart materials. Fish exemplify the use of flexible materials to generate forces during locomotion, and a hallmark of fish functional design is the use of body and fin deformation to power propulsion and maneuvering. As a result of nearly 500 million years of evolutionary experimentation, fish design has a number of interesting features of note to materials engineers. In this paper we first provide a brief general overview of some key features of the mechanical design of fish, and then focus on two key properties of fish: the bilaminar mechanical design of bony fish fin rays that allows active muscular control of curvature, and the role of body flexibility in propulsion. After describing the anatomy of bony fish fin rays, we provide new data on their mechanical properties. Three-point bending tests and measurement of force inputs to and outputs from the fin rays show that these fin rays are effective displacement transducers. Fin rays in different regions of the fin differ considerably in their material properties, and in the curvature produced by displacement of one of the two fin ray halves. The mean modulus for the proximal (basal) region of the fin rays was 1.34 GPa, but this varied from 0.24 to 3.7 GPa for different fin rays. The distal fin region was less stiff, and moduli for the different fin rays measured varied from 0.11 to 0.67 GPa. These data are similar to those for human tendons (modulus around 0.5 GPa). Analysis of propulsion using flexible foils controlled using a robotic flapping device allows investigation of the effect of altering flexural stiffness on swimming speed. Flexible foils with the leading edge moved in a heave show a distinct peak in propulsive performance, while the addition of pitch input produces a broad plateau where the swimming speed is relatively unaffected by the flexural stiffness. Our understanding of the material design of fish and the control of tissue

Inadequate pre-season preparation of schoolboy rugby players - a ...

African Journals Online (AJOL)

... in prospective studies at the same schools. The players' knowledge of techniques known to prevent rugby injuries was inadequate and too little attention was paid at the start of the rugby season to training and coaching techniques to reduce injury risk. Coaching errors may therefore have predisposed players to injury.

Cognitive Attributes of Adequate and Inadequate Responders to Reading Intervention in Middle School

OpenAIRE

Miciak, Jeremy; Stuebing, Karla K.; Vaughn, Sharon; Roberts, Greg; Barth, Amy Elizabeth; Fletcher, Jack M.

2014-01-01

No studies have investigated the cognitive attributes of middle school students who are adequate and inadequate responders to Tier 2 reading intervention. We compared students in Grades 6 and 7 representing groups of adequate responders (n = 77) and inadequate responders who fell below criteria in (a) comprehension (n = 54); (b) fluency (n = 45); and (c) decoding, fluency, and comprehension (DFC; n = 45). These students received measures of phonological awareness, listening comprehension, rap...

Virtual Welded-Joint Design Integrating Advanced Materials and Processing Technologies

Energy Technology Data Exchange (ETDEWEB)

Yang, Z.; Dong, P.; Liu, S.; Babu, S.; Olson, G.; DebRoy, T.

2005-04-15

The primary goal of this project is to increase the fatigue life of a welded-joint by 10 times and to reduce energy use by 25% through product performance and productivity improvements using an integrated modeling approach. The fatigue strength of a welded-joint is currently the bottleneck to design high performance and lightweight welded structures using advanced materials such as high strength steels. In order to achieve high fatigue strength in a welded-joint it is necessary to manage the weld bead shape for lower stress concentration, produce preferable residual stress distribution, and obtain the desired microstructure for improved material toughness and strength. This is a systems challenge that requires the optimization of the welding process, the welding consumable, the base material, as well as the structure design. The concept of virtual welded-joint design has been proposed and established in this project. The goal of virtual welded-joint design is to develop a thorough procedure to predict the relationship of welding process, microstructure, property, residual stress, and the ultimate weld fatigue strength by a systematic modeling approach. The systematic approach combines five sub-models: weld thermal-fluid model, weld microstructure model, weld material property model, weld residual stress model, and weld fatigue model. The systematic approach is thus based on interdisciplinary applied sciences including heat transfer, computational fluid dynamics, materials science, engineering mechanics, and material fracture mechanics. The sub-models are based on existing models with further development. The results from modeling have been validated with critical experiments. The systematic modeling approach has been used to design high fatigue resistant welds considering the combined effects of weld bead geometry, residual stress, microstructure, and material property. In particular, a special welding wire has been developed in this project to introduce

Multi-material topology design of laminates with strength criteria

DEFF Research Database (Denmark)

Lund, Erik

2012-01-01

The objective of this paper is to present a novel approach for multi-material topology optimization of laminated composite structures where strength constraints are taken into account together with other global structural performance measures. The topology design problem considered contains very...... many design variables, and when strength criteria are included in the problem, a very large number of criteria functions must be considered in the optimization problem to be solved. Thus, block aggregation methods are introduced, such that global strength measures are obtained. These formulations...... are illustrated for multi-material laminated design problems where the maximum failure index is minimized while compliance and mass constraints are taken into account....

The association between inadequate prenatal care and future healthcare use among offspring in the Bedouin population.

Science.gov (United States)

Estis-Deaton, Asia; Sheiner, Eyal; Wainstock, Tamar; Landau, Daniella; Walfisch, Asnat

2017-12-01

To evaluate the impact of inadequate prenatal care on long-term morbidity among the offspring of an ethnic minority population. A retrospective population-based cohort analysis was performed among all Bedouin women with singleton pregnancies who delivered in a tertiary medical center in Israel between January 1, 1991, and January 1, 2014. Morbidity was defined as pediatric hospitalization across six distinct disease categories before 18 years of age. The cumulative morbidity rates were compared for offspring born following pregnancies with either inadequate (prenatal care facility) or adequate prenatal care. Overall, 127 396 neonates were included; 19 173 (15.0%) were born following inadequate prenatal care. Pediatric hospitalizations for all morbidities other than cardiovascular ones were less frequent among the inadequate prenatal care group than the adequate prenatal care group (Pprenatal care group, with the exception of cardiovascular disease. Inadequate prenatal care correlated with reduced pediatric hospitalization rates among offspring, possibly owing to a lack of child healthcare service utilization within the Bedouin population. © 2017 International Federation of Gynecology and Obstetrics.

Psychological distress is associated with inadequate dietary intake in Vietnamese marriage immigrant women in Korea.

Science.gov (United States)

Hwang, Ji-Yun; Lee, Sang Eun; Kim, Sun Hye; Chung, Hye Won; Kim, Wha Young

2010-05-01

Previous studies have reported that the nutritional status of Vietnamese female marriage immigrants in Korea is inadequate. And the mediation of acculturation stress can contribute to problems in their eating practices and dietary intakes. This study examines an association between psychological distress and inadequate dietary intake in Vietnamese female marriage immigrants living in Korea. A cross-sectional study analyzed baseline data (n=570) from the Cohort of Intermarried Women in Korea. Daily nutrient intakes were compared according to the quartiles of distress scores assessed by the Psychological Well-Being Index-Short Form. One-way analysis of variance and chi(2) tests were used to compare eating practices and nutrient intake across quartiles of psychological distress. Subjects in the highest stress scores were more likely to skip breakfast and to change their dietary habits after living in Korea than those in groups with low stress scores. Analyses of the subjects' Mini Dietary Assessments revealed that those with the highest stress scores were less likely to consume milk or dairy products, eat regular meals, or have balanced diets than those with the lowest stress scores. Nutrient intakes were found to be inadequate in the subjects, and those with the highest stress scores showed lower consumptions of energy, carbohydrate, protein, fat, calcium, zinc, thiamin, riboflavin, and folate compared to those with the lowest scores. The prevalence of underweight (body mass index [calculated as kg/m(2)] Korea was negatively associated with dietary intake. These findings can assist dietetics practitioners working with minority immigrants because such information is important in designing appropriate strategies for dietary counseling. A follow-up study should address the underlying mechanisms of the observed diet-distress association in Vietnamese marriage immigrant women in Korea, as well as other various ethnic minority immigrants in Korea. Copyright 2010 American

Inverse problems in complex material design: Applications to non-crystalline solids

Science.gov (United States)

Biswas, Parthapratim; Drabold, David; Elliott, Stephen

The design of complex amorphous materials is one of the fundamental problems in disordered condensed-matter science. While impressive developments of ab-initio simulation methods during the past several decades have brought tremendous success in understanding materials property from micro- to mesoscopic length scales, a major drawback is that they fail to incorporate existing knowledge of the materials in simulation methodologies. Since an essential feature of materials design is the synergy between experiment and theory, a properly developed approach to design materials should be able to exploit all available knowledge of the materials from measured experimental data. In this talk, we will address the design of complex disordered materials as an inverse problem involving experimental data and available empirical information. We show that the problem can be posed as a multi-objective non-convex optimization program, which can be addressed using a number of recently-developed bio-inspired global optimization techniques. In particular, we will discuss how a population-based stochastic search procedure can be used to determine the structure of non-crystalline solids (e.g. a-SiH, a-SiO2, amorphous graphene, and Fe and Ni clusters). The work is partially supported by NSF under Grant Nos. DMR 1507166 and 1507670.

"Intelligent" design of molecular materials: Understanding the concepts of design in supramolecular synthesis of network solids

Science.gov (United States)

Moulton, Brian D.

This work endeavors to delineate modern paradigms for crystal engineering, i.e. the design and supramolecular synthesis of functional molecular materials. Paradigms predicated on an understanding of the geometry of polygons and polyhedra are developed. The primary focus is on structural determination by single crystal X-ray crystallography, structural interpretation using a suite of graphical visualization and molecular modeling software, and on the importance of proper graphical representation in the presentation and explanation of crystal structures. A detailed analysis of a selected series of crystal structures is presented. The reduction of these molecular networks to schematic representations that illustrate their fundamental connectivity facilitates the understanding of otherwise complex supramolecular solids. Circuit symbols and Schlafli notation are used to describe the network topologies, which enables networks of different composition and metrics to be easily compared. This reveals that molecular orientations in the crystals and networks are commensurate with networks that can be derived from spherical close packed lattices. The development of a logical design strategy for a new class of materials based on our understanding of the chemical composition and topology of these networks is described. The synthesis and crystal structure of a series of new materials generated by exploitation of this design strategy is presented, in addition to a detailed analysis of the topology of these materials and their relationship to a 'parent' structure. In summary, this dissertation demonstrates that molecular polygons can self-assemble at their vertexes to produce molecular architectures and crystal structures that are consistent with long established geometric dogma. The design strategy represents a potentially broad ranging approach to the design of nanoporous structures from a wide range of chemical components that are based on molecular shape rather than chemical

Materials-by-design: computation, synthesis, and characterization from atoms to structures

Science.gov (United States)

Yeo, Jingjie; Jung, Gang Seob; Martín-Martínez, Francisco J.; Ling, Shengjie; Gu, Grace X.; Qin, Zhao; Buehler, Markus J.

2018-05-01

In the 50 years that succeeded Richard Feynman’s exposition of the idea that there is ‘plenty of room at the bottom’ for manipulating individual atoms for the synthesis and manufacturing processing of materials, the materials-by-design paradigm is being developed gradually through synergistic integration of experimental material synthesis and characterization with predictive computational modeling and optimization. This paper reviews how this paradigm creates the possibility to develop materials according to specific, rational designs from the molecular to the macroscopic scale. We discuss promising techniques in experimental small-scale material synthesis and large-scale fabrication methods to manipulate atomistic or macroscale structures, which can be designed by computational modeling. These include recombinant protein technology to produce peptides and proteins with tailored sequences encoded by recombinant DNA, self-assembly processes induced by conformational transition of proteins, additive manufacturing for designing complex structures, and qualitative and quantitative characterization of materials at different length scales. We describe important material characterization techniques using numerous methods of spectroscopy and microscopy. We detail numerous multi-scale computational modeling techniques that complements these experimental techniques: DFT at the atomistic scale; fully atomistic and coarse-grain molecular dynamics at the molecular to mesoscale; continuum modeling at the macroscale. Additionally, we present case studies that utilize experimental and computational approaches in an integrated manner to broaden our understanding of the properties of two-dimensional materials and materials based on silk and silk-elastin-like proteins.

Self-esteem, social support, and satisfaction differences in women with adequate and inadequate prenatal care.

Science.gov (United States)

Higgins, P; Murray, M L; Williams, E M

1994-03-01

This descriptive, retrospective study examined levels of self-esteem, social support, and satisfaction with prenatal care in 193 low-risk postpartal women who obtained adequate and inadequate care. The participants were drawn from a regional medical center and university teaching hospital in New Mexico. A demographic questionnaire, the Coopersmith self-esteem inventory, the personal resource questionnaire part 2, and the prenatal care satisfaction inventory were used for data collection. Significant differences were found in the level of education, income, insurance, and ethnicity between women who received adequate prenatal care and those who received inadequate care. Women who were likely to seek either adequate or inadequate prenatal care were those whose total family income was $10,000 to $19,999 per year and high school graduates. Statistically significant differences were found in self-esteem, social support, and satisfaction between the two groups of women. Strategies to enhance self-esteem and social support have to be developed to reach women at risk for receiving inadequate prenatal care.

Big-deep-smart data in imaging for guiding materials design

Science.gov (United States)

Kalinin, Sergei V.; Sumpter, Bobby G.; Archibald, Richard K.

2015-10-01

Harnessing big data, deep data, and smart data from state-of-the-art imaging might accelerate the design and realization of advanced functional materials. Here we discuss new opportunities in materials design enabled by the availability of big data in imaging and data analytics approaches, including their limitations, in material systems of practical interest. We specifically focus on how these tools might help realize new discoveries in a timely manner. Such methodologies are particularly appropriate to explore in light of continued improvements in atomistic imaging, modelling and data analytics methods.

Skull-base Osteomyelitis: a Dreaded Complication after Trivial Fall and Inadequate Management

Directory of Open Access Journals (Sweden)

Kundan Mittal

2015-10-01

Full Text Available Introduction: Skull-based osteomyelitis is bony infection which generally originates from inadequately treated chronic infection, adjoining tissue infection or after trauma.Case: 11 month female child had a trivial fall while standing near a bucket. The child developed fracture of right clavicle and left orbital swelling which was inadequately treated. This resulted in in spread of infection to adjoining tissues, skull bones, sinuses and brain.Conclusion: Cranial base osteomyelitis is rare but dreaded condition which requires early diagnosis and prompt treatment to avoid mortality and morbidity in form of neurological deficits and permanent disability

Do infants with cow's milk protein allergy have inadequate levels of vitamin D?

Science.gov (United States)

Silva, Cristiane M; Silva, Silvia A da; Antunes, Margarida M de C; Silva, Gisélia Alves Pontes da; Sarinho, Emanuel Sávio Cavalcanti; Brandt, Katia G

To verify whether infants with cow's milk protein allergy have inadequate vitamin D levels. This cross-sectional study included 120 children aged 2 years or younger, one group with cow's milk protein allergy and a control group. The children were recruited at the pediatric gastroenterology, allergology, and pediatric outpatient clinics of a university hospital in the Northeast of Brazil. A questionnaire was administered to the caregiver and blood samples were collected for vitamin D quantification. Vitamin D levels <30ng/mL were considered inadequate. Vitamin D level was expressed as mean and standard deviation, and the frequency of the degrees of sufficiency and other variables, as proportions. Infants with cow's milk protein allergy had lower mean vitamin D levels (30.93 vs.35.29ng/mL; p=0.041) and higher deficiency frequency (20.3% vs.8.2; p=0.049) than the healthy controls. Exclusively or predominantly breastfed infants with cow's milk protein allergy had higher frequency of inadequate vitamin D levels (p=0.002). Regardless of sun exposure time, the groups had similar frequencies of inadequate vitamin D levels (p=0.972). Lower vitamin D levels were found in infants with CMPA, especially those who were exclusively or predominantly breastfed, making these infants a possible risk group for vitamin D deficiency. Copyright © 2017 Sociedade Brasileira de Pediatria. Published by Elsevier Editora Ltda. All rights reserved.

Do infants with cow's milk protein allergy have inadequate levels of vitamin D?

Directory of Open Access Journals (Sweden)

Cristiane M. Silva

Full Text Available Abstract Objective: To verify whether infants with cow's milk protein allergy have inadequate vitamin D levels. Methods: This cross-sectional study included 120 children aged 2 years or younger, one group with cow's milk protein allergy and a control group. The children were recruited at the pediatric gastroenterology, allergology, and pediatric outpatient clinics of a university hospital in the Northeast of Brazil. A questionnaire was administered to the caregiver and blood samples were collected for vitamin D quantification. Vitamin D levels <30 ng/mL were considered inadequate. Vitamin D level was expressed as mean and standard deviation, and the frequency of the degrees of sufficiency and other variables, as proportions. Results: Infants with cow's milk protein allergy had lower mean vitamin D levels (30.93 vs.35.29 ng/mL; p = 0.041 and higher deficiency frequency (20.3% vs.8.2; p = 0.049 than the healthy controls. Exclusively or predominantly breastfed infants with cow's milk protein allergy had higher frequency of inadequate vitamin D levels (p = 0.002. Regardless of sun exposure time, the groups had similar frequencies of inadequate vitamin D levels (p = 0.972. Conclusions: Lower vitamin D levels were found in infants with CMPA, especially those who were exclusively or predominantly breastfed, making these infants a possible risk group for vitamin D deficiency.

Magnitude and determinants of inadequate third-trimester weight gain in rural Bangladesh

Science.gov (United States)

Hasan, S. M. Tafsir; Rahman, Sabuktagin; Locks, Lindsey Mina; Rahman, Mizanur; Hore, Samar Kumar; Saqeeb, Kazi Nazmus; Khan, Md. Alfazal

2018-01-01

Objectives The objective of this study was to estimate the magnitude and determinants of inadequate weight gain in the third-trimester among rural women in Matlab, Bangladesh. Methods The study analyzed data on weight gain in the third trimester in 1,883 pregnant women in Matlab, Bangladesh. All these women were admitted to Matlab hospital of the International Centre for Diarrhoeal Disease Research, Bangladesh (icddr,b) for childbirth during 2012–2014, and they had singleton live births at term. Data were retrieved from the electronic databases of Matlab Health and Demographic Surveillance System and Matlab hospital. A multivariable logistic regression for inadequate weight gain in the third trimester (≤4 kg) was built with sociodemographic, environmental and maternal factors as predictors. Results One thousand and twenty-six (54%) pregnant women had inadequate weight gain in the third trimester. In the multivariable model, short stature turned out to be the most robust risk factor for inadequate weight gain in the third trimester (OR = 2.5; 95% CI 1.8, 3.5 for short compared to tall women). Pre-third-trimester BMI was inversely associated with insufficient weight gain (OR = 0.96; 95% CI 0.93, 0.99 for 1 unit increase in BMI). Other risk factors for inadequate weight gain in the third trimester were advanced age (OR = 1.9; 95% CI 1.2, 3.1 for ≥35 years compared to ≤19 years), parity (OR = 1.5; 95% CI 1.2, 1.9 for multipara compared to nulliparous women), low socioeconomic status (OR = 1.7; 95% CI 1.2, 2.3 for women in the lowest compared to women in the highest wealth quintile), low level of education (OR = 1.6; 95% CI 1.2, 2.1 for ≤5 years compared to ≥10 years of education), belonging to the Hindu religious community (OR = 1.8; 95% CI 1.3, 2.5), consuming arsenic-contaminated water (OR = 1.4; 95% CI 1.1, 1.9), and conceiving during monsoon or dry season compared to summer (OR = 1.4; 95% CI 1.1, 1.8). Conclusions Among rural Bangladeshi women in Matlab

Magnitude and determinants of inadequate third-trimester weight gain in rural Bangladesh.

Science.gov (United States)

Hasan, S M Tafsir; Rahman, Sabuktagin; Locks, Lindsey Mina; Rahman, Mizanur; Hore, Samar Kumar; Saqeeb, Kazi Nazmus; Khan, Md Alfazal; Ahmed, Tahmeed

2018-01-01

The objective of this study was to estimate the magnitude and determinants of inadequate weight gain in the third-trimester among rural women in Matlab, Bangladesh. The study analyzed data on weight gain in the third trimester in 1,883 pregnant women in Matlab, Bangladesh. All these women were admitted to Matlab hospital of the International Centre for Diarrhoeal Disease Research, Bangladesh (icddr,b) for childbirth during 2012-2014, and they had singleton live births at term. Data were retrieved from the electronic databases of Matlab Health and Demographic Surveillance System and Matlab hospital. A multivariable logistic regression for inadequate weight gain in the third trimester (≤4 kg) was built with sociodemographic, environmental and maternal factors as predictors. One thousand and twenty-six (54%) pregnant women had inadequate weight gain in the third trimester. In the multivariable model, short stature turned out to be the most robust risk factor for inadequate weight gain in the third trimester (OR = 2.5; 95% CI 1.8, 3.5 for short compared to tall women). Pre-third-trimester BMI was inversely associated with insufficient weight gain (OR = 0.96; 95% CI 0.93, 0.99 for 1 unit increase in BMI). Other risk factors for inadequate weight gain in the third trimester were advanced age (OR = 1.9; 95% CI 1.2, 3.1 for ≥35 years compared to ≤19 years), parity (OR = 1.5; 95% CI 1.2, 1.9 for multipara compared to nulliparous women), low socioeconomic status (OR = 1.7; 95% CI 1.2, 2.3 for women in the lowest compared to women in the highest wealth quintile), low level of education (OR = 1.6; 95% CI 1.2, 2.1 for ≤5 years compared to ≥10 years of education), belonging to the Hindu religious community (OR = 1.8; 95% CI 1.3, 2.5), consuming arsenic-contaminated water (OR = 1.4; 95% CI 1.1, 1.9), and conceiving during monsoon or dry season compared to summer (OR = 1.4; 95% CI 1.1, 1.8). Among rural Bangladeshi women in Matlab, third-trimester weight gain was in

Software Performs Complex Design Analysis

Science.gov (United States)

2008-01-01

Designers use computational fluid dynamics (CFD) to gain greater understanding of the fluid flow phenomena involved in components being designed. They also use finite element analysis (FEA) as a tool to help gain greater understanding of the structural response of components to loads, stresses and strains, and the prediction of failure modes. Automated CFD and FEA engineering design has centered on shape optimization, which has been hindered by two major problems: 1) inadequate shape parameterization algorithms, and 2) inadequate algorithms for CFD and FEA grid modification. Working with software engineers at Stennis Space Center, a NASA commercial partner, Optimal Solutions Software LLC, was able to utilize its revolutionary, one-of-a-kind arbitrary shape deformation (ASD) capability-a major advancement in solving these two aforementioned problems-to optimize the shapes of complex pipe components that transport highly sensitive fluids. The ASD technology solves the problem of inadequate shape parameterization algorithms by allowing the CFD designers to freely create their own shape parameters, therefore eliminating the restriction of only being able to use the computer-aided design (CAD) parameters. The problem of inadequate algorithms for CFD grid modification is solved by the fact that the new software performs a smooth volumetric deformation. This eliminates the extremely costly process of having to remesh the grid for every shape change desired. The program can perform a design change in a markedly reduced amount of time, a process that would traditionally involve the designer returning to the CAD model to reshape and then remesh the shapes, something that has been known to take hours, days-even weeks or months-depending upon the size of the model.

Lightweight structure design for wind energy by integrating nanostructured materials

International Nuclear Information System (INIS)

Li, Ying; Lu, Jian

2014-01-01

Highlights: • Integrate high-strength nano-materials into lightweight design. • Lightweight design scheme for wind turbine tower application. • Expand the bending formulae for tapered tubular structures with varying thickness. • We rewrite the Secant Formula for a tapered beam under eccentric compression. - Abstract: Wind power develops very fast nowadays with high expectation. Although at the mean time, the use of taller towers, however, smacks head-on into the issue of transportability. The engineering base and computational tools have to be developed to match machine size and volume. Consequently the research on the light weight structures of tower is carrying out in the main countries which are actively developing wind energy. This paper reports a new design scheme of light weight structure for wind turbine tower. This design scheme is based on the integration of the nanostructured materials produced by the Surface Mechanical Attrition Treatment (SMAT) process. The objective of this study is to accomplish the weight reduction by optimizing the wall thickness of the tapered tubular structure. The basic methods include the identification of the critical zones and the distribution of the high strength materials according to different necessities. The equivalent strength or stiffness design method and the high strength material properties after SMAT process are combined together. Bending and buckling are two main kinds of static loads concerned in consideration. The study results reveal that there is still enough margin for weight reduction in the traditional wind turbine tower design

Data Science and Optimal Learning for Material Discovery and Design

Science.gov (United States)

; Optimal Learning for Material Discovery & Design Data Science and Optimal Learning for Material inference and optimization methods that can constrain predictions using insights and results from theory directions in the application of information theoretic tools to materials problems related to learning from

Heat stress and inadequate sanitary facilities at workplaces - an occupational health concern for women?

Science.gov (United States)

Venugopal, Vidhya; Rekha, Shanmugam; Manikandan, Krishnamoorthy; Latha, Perumal Kamalakkannan; Vennila, Viswanathan; Ganesan, Nalini; Kumaravel, Perumal; Chinnadurai, Stephen Jeremiah

2016-01-01

Health concerns unique to women are growing with the large number of women venturing into different trades that expose them to hot working environments and inadequate sanitation facilities, common in many Indian workplaces. The study was carried out to investigate the health implications of exposures to hot work environments and inadequate sanitation facilities at their workplaces for women workers. A cross-sectional study was conducted with 312 women workers in three occupational sectors in 2014-2015. Quantitative data on heat exposures and physiological heat strain indicators such as core body temperature (CBT), sweat rate (SwR), and urine specific gravity (USG) were collected. A structured questionnaire captured workers perceptions about health impacts of heat stress and inadequate sanitary facilities at the workplace. Workplace heat exposures exceeded the threshold limit value for safe manual work for 71% women (Avg. wet bulb globe temperature=30°C±2.3°C) during the study period. Eighty-seven percent of the 200 women who had inadequate/no toilets at their workplaces reported experiencing genitourinary problems periodically. Above normal CBT, SwR, and USG in about 10% women workers indicated heat strain and moderate dehydration that corroborated well with their perceptions. Observed significant associations between high-heat exposures and SwR (t=-2.3879, p=0.0192), inadequate toilet facilities and self-reported adverse heat-related health symptoms (χ (2)=4.03, p=0.0444), and prevalence of genitourinary issues (χ (2)=42.92, p=0.0005×10(-7)) reemphasize that heat is a risk and lack of sanitation facilities is a major health concern for women workers. The preliminary evidence suggests that health of women workers is at risk due to occupational heat exposures and inadequate sanitation facilities at many Indian workplaces. Intervention through strong labor policies with gender sensitivity is the need of the hour to empower women, avert further health risks, and

Advanced materials for aqueous supercapacitors in the asymmetric design

Directory of Open Access Journals (Sweden)

Muniyandi Rajkumar

2015-12-01

Full Text Available Supercapacitors have been recognized as one of the promising energy storage devices in the future energy technology. In this perspective, rapid progress is made in the development of fundamental and applied aspects of supercapacitors. Various techniques have been developed specifically to estimate the specific capacitance. Numerous efforts have been made in the literature to increase the specific capacitance of electrode materials. Recently, researchers pay more attention on designing supercapacitors of asymmetric type with extending cell voltage and dissimilar materials with complementary working potentials. Researchers try to increase the specific energy of asymmetric supercapacitors (ASCs. Conversely, it is still a challenge to find a suitable operation conditions for ASCs in various designs, especially for the one with battery type electrode. In this review, we describe our recent research works and other reports on the preparation of various nanostructured electrode materials and the performances of both symmetric and asymmetric supercapacitors. Finally, we demonstrate effects of charge balance on the capacitive performances of ASCs which consist of one electrode material of the battery type and one capacitive material. We also demonstrate how to evaluate the charge capacities of both positive and negative electrode materials for this ASC application.

Wide band design on the scaled absorbing material filled with flaky CIPs

Science.gov (United States)

Xu, Yonggang; Yuan, Liming; Gao, Wei; Wang, Xiaobing; Liang, Zichang; Liao, Yi

2018-02-01

The scaled target measurement is an important method to get the target characteristic. Radar absorbing materials are widely used in the low detectable target, considering the absorbing material frequency dispersion characteristics, it makes designing and manufacturing scaled radar absorbing materials on the scaled target very difficult. This paper proposed a wide band design method on the scaled absorbing material of the thin absorption coating with added carbonyl iron particles. According to the theoretical radar cross section (RCS) of the plate, the reflection loss determined by the permittivity and permeability was chosen as the main design factor. Then, the parameters of the scaled absorbing materials were designed using the effective medium theory, and the scaled absorbing material was constructed. Finally, the full-size coating plate and scaled coating plates (under three different scale factors) were simulated; the RCSs of the coating plates were numerically calculated and measured at 4 GHz and a scale factor of 2. The results showed that the compensated RCS of the scaled coating plate was close to that of the full-size coating plate, that is, the mean deviation was less than 0.5 dB, and the design method for the scaled material was very effective.

Consequences of Inadequate Staffing Include Missed Care, Potential Failure to Rescue, and Job Stress and Dissatisfaction.

Science.gov (United States)

Simpson, Kathleen Rice; Lyndon, Audrey; Ruhl, Catherine

2016-01-01

To evaluate responses of registered nurse members of the Association of Women's Health, Obstetric and Neonatal Nurses (AWHONN) to a survey that sought their recommendations for staffing guidelines and their perceptions of the consequences of inadequate nurse staffing. The goal was to use these member data to inform the work of the AWHONN nurse staffing research team. Secondary analysis of responses to the 2010 AWHONN nurse staffing survey. Online. AWHONN members (N = 884). Review of data from an online survey of AWHONN members through the use of thematic analysis for descriptions of the consequences of inadequate nurse staffing during the childbirth process. Three main themes emerged as consequences of inadequate staffing or being short-staffed: Missed Care, Potential for Failure to Rescue, and Job-Related Stress and Dissatisfaction. These themes are consistent with those previously identified in the literature related to inadequate nurse staffing. Based on the responses from participants in the 2010 AWHONN nurse staffing survey, consequences of inadequate staffing can be quite serious and may put patients at risk for preventable harm. Copyright © 2016 AWHONN, the Association of Women's Health, Obstetric and Neonatal Nurses. Published by Elsevier Inc. All rights reserved.

Designing high-Performance layered thermoelectric materials through orbital engineering

DEFF Research Database (Denmark)

Zhang, Jiawei; Song, Lirong; Madsen, Georg K. H.

2016-01-01

Thermoelectric technology, which possesses potential application in recycling industrial waste heat as energy, calls for novel high-performance materials. The systematic exploration of novel thermoelectric materials with excellent electronic transport properties is severely hindered by limited...... insight into the underlying bonding orbitals of atomic structures. Here we propose a simple yet successful strategy to discover and design high-performance layered thermoelectric materials through minimizing the crystal field splitting energy of orbitals to realize high orbital degeneracy. The approach...... naturally leads to design maps for optimizing the thermoelectric power factor through forming solid solutions and biaxial strain. Using this approach, we predict a series of potential thermoelectric candidates from layered CaAl2Si2-type Zintl compounds. Several of them contain nontoxic, low-cost and earth...

A Tutorial Design Process Applied to an Introductory Materials Engineering Course

Science.gov (United States)

Rosenblatt, Rebecca; Heckler, Andrew F.; Flores, Katharine

2013-01-01

We apply a "tutorial design process", which has proven to be successful for a number of physics topics, to design curricular materials or "tutorials" aimed at improving student understanding of important concepts in a university-level introductory materials science and engineering course. The process involves the identification…

Growing grass: a smart material interactive display, design and construction history

NARCIS (Netherlands)

Minuto, A.; Nijholt, Antinus

2012-01-01

In this paper we will present the design process and development of "Follow the Grass", our smart material interactive pervasive display, with related technical detailed explanation. We will present the design steps and prototypes with instructions for the use of smart materials (NiTiNOL) to create

Molecular modeling for the design of novel performance chemicals and materials

CERN Document Server

Rai, Beena

2012-01-01

Molecular modeling (MM) tools offer significant benefits in the design of industrial chemical plants and material processing operations. While the role of MM in biological fields is well established, in most cases MM works as an accessory in novel products/materials development rather than a tool for direct innovation. As a result, MM engineers and practitioners are often seized with the question: ""How do I leverage these tools to develop novel materials or chemicals in my industry?"" Molecular Modeling for the Design of Novel Performance Chemicals and Materials answers this important questio

Becoming a Do-it-yourself Designer of English Language Teaching Materials

Directory of Open Access Journals (Sweden)

Mark Wyatt

2011-01-01

Full Text Available Many language teachers around the world design materials to supplement those they are provided with to address the needs of the learners in their particular context. This is a task which requires practical knowledge of various kinds relating to learners and language learning, teaching and materials design. However, while there is a growing body of research into the practical knowledge of language teachers, little of this is longitudinal and there is a lack of research into how teachers develop as materials designers. This article focuses on one teacher's growth as a DIY (do-it-yourself designer of English language teaching materials during an in-service BA TESOL (teaching English to speakers of other languages programme in the Middle East. Using qualitative case study methodology, I follow the teacher's development over three years, exploring changes in ideas and teaching practices. Implications for in-service language teacher education are discussed. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1101334

Impermeable layers in landfill design

Directory of Open Access Journals (Sweden)

Karanac Milica

2013-01-01

Full Text Available Landfills are complex systems which could potentially contaminate the environment. It should be prevented by providing impermeability during the landfill design. In that aim related regulations should be followed and adequate materials that provide impermeability should be used. The first part of the paper presents review of the current regulations, interpretations, and recommendations from U.S., EU and Republic of Serbia. Knowing that the Serbian regulation should fully follow related European Directive, in analyses some inadequate formulations and terms were observed related to the Directive Annex I, 3.2. Request of the Regulation that deals with the bottom of the landfill leakage is formulated differently than in Directive as well. Mentioned problems enable some design solutions which are not among the best available techniques. In the second part the paper presents comparative analysis of possible alternatives in impermeable layer design, both for the bottom and landfill cover. Some materials like clay, CCL, GCL might not be able to satisfy prescribed requirements. The longest lifetime and the lowest coefficient of permeability, as well as excellent mechanical, chemical and thermal stability, show the mixture of sand, bentonite and polymers (PEBSM. [Projekat Ministarstva nauke Republike Srbije, br. TR 34009

Tunable structural color in organisms and photonic materials for design of bioinspired materials

International Nuclear Information System (INIS)

Fudouzi, Hiroshi

2011-01-01

In this paper, the key topics of tunable structural color in biology and material science are overviewed. Color in biology is considered for selected groups of tropical fish, octopus, squid and beetle. It is caused by nanoplates in iridophores and varies with their spacing, tilting angle and refractive index. These examples may provide valuable hints for the bioinspired design of photonic materials. 1D multilayer films and 3D colloidal crystals with tunable structural color are overviewed from the viewpoint of advanced materials. The tunability of structural color by swelling and strain is demonstrated on an example of opal composites. (topical review)

Tunable structural color in organisms and photonic materials for design of bioinspired materials

Directory of Open Access Journals (Sweden)

Hiroshi Fudouzi

2011-01-01

Full Text Available In this paper, the key topics of tunable structural color in biology and material science are overviewed. Color in biology is considered for selected groups of tropical fish, octopus, squid and beetle. It is caused by nanoplates in iridophores and varies with their spacing, tilting angle and refractive index. These examples may provide valuable hints for the bioinspired design of photonic materials. 1D multilayer films and 3D colloidal crystals with tunable structural color are overviewed from the viewpoint of advanced materials. The tunability of structural color by swelling and strain is demonstrated on an example of opal composites.

Tunable structural color in organisms and photonic materials for design of bioinspired materials

Science.gov (United States)

Fudouzi, Hiroshi

2011-01-01

In this paper, the key topics of tunable structural color in biology and material science are overviewed. Color in biology is considered for selected groups of tropical fish, octopus, squid and beetle. It is caused by nanoplates in iridophores and varies with their spacing, tilting angle and refractive index. These examples may provide valuable hints for the bioinspired design of photonic materials. 1D multilayer films and 3D colloidal crystals with tunable structural color are overviewed from the viewpoint of advanced materials. The tunability of structural color by swelling and strain is demonstrated on an example of opal composites. PMID:27877454

Graded territories: Towards the design, specification and simulation of materially graded bending active structures

DEFF Research Database (Denmark)

Nicholas, Paul; Tamke, Martin; Ramsgaard Thomsen, Mette

2012-01-01

these structures, the property of bending is activated and varied through bespoke material means so as to match a desired form. Within the architectural design process, formal control depends upon design approaches for material specification and simulation that consider behavior at the level of the material...... element as well as the structure. We describe an evolving approach to material specification and simulation, and highlight the digital and material considerations that frame the process.......The ability to make materials with bespoke behavior affords new perspectives on incorporating material properties within the design process not available through natural materials. This paper reports the design and assembly of two bending-active, fibre-reinforced composite structures. Within...

Materials selection in micromechanical design: an application of the Ashby approach

OpenAIRE

Srikar, V.T.; Spearing, S.M.

2003-01-01

The set of materials available to microsystems designers is rapidly expanding. Techniques now exist to introduce and integrate a large number of metals, alloys, ceramics, glasses, polymers, and elastomers into microsystems, motivating the need for a rational approach for materials selection in microsystems design. As a step toward such an approach, we focus on the initial stages of materials selection for micromechanical structures with minimum feature sizes greater than 1 /spl mu/m. The vari...

Nickel-Tin Electrode Materials for Nonaqueous Li-Ion Cells

Science.gov (United States)

Ehrlich, Grant M.; Durand, Christopher

2005-01-01

Experimental materials made from mixtures of nickel and tin powders have shown promise for use as the negative electrodes of rechargeable lithium-ion electrochemical power cells. During charging (or discharging) of a lithium-ion cell, lithium ions are absorbed into (or desorbed from, respectively) the negative electrode, typically through an intercalation or alloying process. The negative electrodes (for this purpose, designated as anodes) in state-of-the-art Li-ion cells are made of graphite, in which intercalation occurs. Alternatively, the anodes can be made from metals, in which alloying can occur. For reasons having to do with the electrochemical potential of intercalated lithium, metallic anode materials (especially materials containing tin) are regarded as safer than graphite ones; in addition, such metallic anode materials have been investigated in the hope of obtaining reversible charge/discharge capacities greater than those of graphite anodes. However, until now, each of the tin-containing metallic anode formulations tested has been found to be inadequate in some respect.

Engaging Students On-Line:Does Gender Matter in Adoption of Learning Material Design?

Directory of Open Access Journals (Sweden)

Norziani Dahalan

2013-12-01

Full Text Available Education is reforming with the birth of the internet. Learning is not solely based on classroom basis but also through on-line. The revolution of Internet has transformed teaching via face-to-face into virtual teaching. The expansion of teaching deliveries suggests that we need interactive mechanism to accommodate course material for on-line students. However, creating on-line materials requires the conception of on-line instructional design. A suitable online material design will allow learners to engage with learning. Learners will have opportunities to develop their own understanding. In addition, suitable learning material will strengthen learner’s knowledge construction from their short-term memory to long-term memory. The purpose of this paper is to discover the learning material design approach based on gender by evaluating lecturer’s adoption of online material design using Keller’s ARCS model. The sample consisting of 30 lecturers from distance education learning reveals that gender differs in their adoption of learning material design specifically on getting attention of the student. The result also shows that relevance and satisfaction contribute to gender differences in learning material adoption. Limitations of the study and practical implications of these findings discussed.

Teaching English Using Video Materials: Design and Delivery of a Practical Course

Science.gov (United States)

Lopez-Alvarado, Julio

2017-01-01

In this paper, a practical course for listening, speaking, reading and writing was designed using authentic video material. The aim of this paper is to offer tools to the TEFL teacher in order to design new course materials using video material. The development procedure is explained in detail, and the underpinning main theories are also…

Design of an intelligent materials data base for the IFR

International Nuclear Information System (INIS)

Mikaili, R.; Lambert, J.D.B.; Orth, T.D.

1992-01-01

In the development of the integral fast reactor (IFR) concept, there is a consensus that materials considerations are an important part of the reactor design, operation, and maintenance and that materials performance is central to liquid-metal reactor reliability and safety. In the design of the IRF materials data base, artificial intelligence techniques are being used to ensure efficient control of information. Intelligent control will provide for the selection of menus to be displayed, efficient data-base searches, and application-dependent guidance through the data base. The development of the IRF data base has progressed to the point of (a) completing the design of the data-base architecture and tables, (b) installing computer hardware for storing large amounts of data, (c) outlining strategies for data transferal, and (d) identifying ways to validate and secure the integrity of data

A general solution to the material performance index for bending strength design

International Nuclear Information System (INIS)

Burgess, S.C.; Pasini, D.; Smith, D.J.; Alemzadeh, K.

2006-01-01

This paper presents a general solution to the material performance index for the bending strength design of beams. In general, the performance index for strength design is ρ f q /ρ where σ f is the material strength, ρ is the material density and q is a function of the direction of scaling. Previous studies have only solved q for three particular cases: proportional scaling of width and height (q=2/3), constrained height (q=1) and constrained width (q=1/2). This paper presents a general solution to the exponent q for any arbitrary direction of scaling. The index is used to produce performance maps that rank relative material performance for particular design cases. The performance index and the performance maps are applied to a design case study

Material orientation design of planar structures with prescribed anisotropy classes. Study of rhombic systems

Science.gov (United States)

Czubacki, Radosław

2018-01-01

The paper deals with the minimum compliance problem of 2D structures made of a non-homogeneous elastic material. In the first part of the paper a comparison between solutions of Free Material Design (FMD), Cubic Material Design (CMD) and Isotropic Material Design (IMD) is shown for a simply supported plate in a shape of a deep beam, subjected to a concentrated in-plane force at its upper face. The isoperimetric condition fixes the value of the cost of the design expressed as the integral of the trace of the Hooke tensor. In the second part of the paper the material design approaches are extended to rhombic system in 2D. For the rhombic system the material properties of the structures are set, the design variables being the trajectories of anisotropy directions which in 2D are described by one parameter. In the Orthotropic Orientation Design (OOD) no isoperimetric condition is used.

Entombment Using Cementitious Materials: Design Considerations and International Experience

Energy Technology Data Exchange (ETDEWEB)

Seitz, Roger Ray

2002-08-01

Cementitious materials have physical and chemical properties that are well suited for the requirements of radioactive waste management. Namely, the materials have low permeability and durability that is consistent with the time frame required for short-lived radionuclides to decay. Furthermore, cementitious materials can provide a long-term chemical environment that substantially reduces the mobility of some long-lived radionuclides of concern for decommissioning (e.g., C-14, Ni-63, Ni-59). Because of these properties, cementitious materials are common in low-level radioactive waste disposal facilities throughout the world and are an attractive option for entombment of nuclear facilities. This paper describes design considerations for cementitious barriers in the context of performance over time frames of a few hundreds of years (directed toward short-lived radionuclides) and time frames of thousands of years (directed towards longer-lived radionuclides). The emphasis is on providing an overview of concepts for entombment that take advantage of the properties of cementitious materials and experience from the design of low-level radioactive waste disposal facilities. A few examples of the previous use of cementitious materials for entombment of decommissioned nuclear facilities and proposals for the use in future decommissioning of nuclear reactors in a few countries are also included to provide global perspective.

Entombment Using Cementitious Materials: Design Considerations and International Experience

Energy Technology Data Exchange (ETDEWEB)

Seitz, R.R.

2002-05-15

Cementitious materials have physical and chemical properties that are well suited for the requirements of radioactive waste management. Namely, the materials have low permeability and durability that is consistent with the time frame required for short-lived radionuclides to decay. Furthermore, cementitious materials can provide a long-term chemical environment that substantially reduces the mobility of some long-lived radionuclides of concern for decommissioning (e.g., C-14, Ni-63, Ni-59). Because of these properties, cementitious materials are common in low-level radioactive waste disposal facilities throughout the world and are an attractive option for entombment of nuclear facilities. This paper describes design considerations for cementitious barriers in the context of performance over time frames of a few hundreds of years (directed toward short-lived radionuclides) and time frames of thousands of years (directed towards longer-lived radionuclides). The emphasis is on providing a n overview of concepts for entombment that take advantage of the properties of cementitious materials and experience from the design of low-level radioactive waste disposal facilities. A few examples of the previous use of cementitious materials for entombment of decommissioned nuclear facilities and proposals for the use in future decommissioning of nuclear reactors in a few countries are also included to provide global perspective.

Entombment Using Cementitious Materials: Design Considerations and International Experience

International Nuclear Information System (INIS)

Seitz, R.R.

2002-01-01

Cementitious materials have physical and chemical properties that are well suited for the requirements of radioactive waste management. Namely, the materials have low permeability and durability that is consistent with the time frame required for short-lived radionuclides to decay. Furthermore, cementitious materials can provide a long-term chemical environment that substantially reduces the mobility of some long-lived radionuclides of concern for decommissioning (e.g., C-14, Ni-63, Ni-59). Because of these properties, cementitious materials are common in low-level radioactive waste disposal facilities throughout the world and are an attractive option for entombment of nuclear facilities. This paper describes design considerations for cementitious barriers in the context of performance over time frames of a few hundreds of years (directed toward short-lived radionuclides) and time frames of thousands of years (directed towards longer-lived radionuclides). The emphasis is on providing a n overview of concepts for entombment that take advantage of the properties of cementitious materials and experience from the design of low-level radioactive waste disposal facilities. A few examples of the previous use of cementitious materials for entombment of decommissioned nuclear facilities and proposals for the use in future decommissioning of nuclear reactors in a few countries are also included to provide global perspective

Computational materials design

International Nuclear Information System (INIS)

Snyder, R.L.

1999-01-01

Full text: Trial and error experimentation is an extremely expensive route to the development of new materials. The coming age of reduced defense funding will dramatically alter the way in which advanced materials have developed. In the absence of large funding we must concentrate on reducing the time and expense that the R and D of a new material consumes. This may be accomplished through the development of computational materials science. Materials are selected today by comparing the technical requirements to the materials databases. When existing materials cannot meet the requirements we explore new systems to develop a new material using experimental databases like the PDF. After proof of concept, the scaling of the new material to manufacture requires evaluating millions of parameter combinations to optimize the performance of the new device. Historically this process takes 10 to 20 years and requires hundreds of millions of dollars. The development of a focused set of computational tools to predict the final properties of new materials will permit the exploration of new materials systems with only a limited amount of materials characterization. However, to bound computational extrapolations, the experimental formulations and characterization will need to be tightly coupled to the computational tasks. The required experimental data must be obtained by dynamic, in-situ, very rapid characterization. Finally, to evaluate the optimization matrix required to manufacture the new material, very rapid in situ analysis techniques will be essential to intelligently monitor and optimize the formation of a desired microstructure. Techniques and examples for the rapid real-time application of XRPD and optical microscopy will be shown. Recent developments in the cross linking of the world's structural and diffraction databases will be presented as the basis for the future Total Pattern Analysis by XRPD. Copyright (1999) Australian X-ray Analytical Association Inc

Three roles for textiles as tangible working materials in co-design processes

DEFF Research Database (Denmark)

Heimdal, Elisabeth Jacobsen; Rosenqvist, Tanja Schultz

2012-01-01

Textiles are increasingly complex materials used in a growing number of applications, e. g. in architecture. The textile industry must therefore engage with other professions when developing both textiles and products of which textiles are a part. In this article, we argue that tools taken from...... the field of participatory design represent a potential for staging such co-design situations and report on our experience from a co-design process where architects, engineers and textile experts engaged in designing future textile solutions for Danish hospital environments. During this process we used what...... we call tangible working materials to stage the collaboration between the stakeholders engaged as co-designers. Our experience using the tangible working materials showed us that they can be divided into three types, with different attributes and roles in the design process: real, mediating...

Factors associated with an inadequate hypoglycemia in the insulin tolerance test in Japanese patients with suspected or proven hypopituitarism.

Science.gov (United States)

Takahashi, Kiyohiko; Nakamura, Akinobu; Miyoshi, Hideaki; Nomoto, Hiroshi; Kameda, Hiraku; Cho, Kyu Yong; Nagai, So; Shimizu, Chikara; Taguri, Masataka; Terauchi, Yasuo; Atsumi, Tatsuya

2017-04-29

We attempted to identify the predictors of an inadequate hypoglycemia in insulin tolerance test (ITT), defined as a blood glucose level higher than 2.8 mmol/L after insulin injection, in Japanese patients with suspected or proven hypopituitarism. A total of 78 patients who had undergone ITT were divided into adequate and inadequate hypoglycemia groups. The relationships between the subjects' clinical parameters and inadequate hypoglycemia in ITT were analyzed. Stepwise logistic regression analysis identified high systolic blood pressure (SBP) and high homeostasis model assessment of insulin resistance (HOMA-IR) as being independent factors associated with inadequate hypoglycemia in ITT. Receiver operating characteristic (ROC) curve analysis revealed the cutoff value for inadequate hypoglycemia was 109 mmHg for SBP and 1.4 for HOMA-IR. The areas under ROC curve for SBP and HOMA-IR were 0.72 and 0.86, respectively. We confirmed that high values of SBP and HOMA-IR were associated with inadequate hypoglycemia in ITT, regardless of the degree of reduction of pituitary hormone levels. Furthermore, the strongest predictor of inadequate hypoglycemia was obtained by using the cutoff value of HOMA-IR. Our results suggest that HOMA-IR is a useful pre-screening tool for ITT in these populations.

Study of New Materials Design based on Hadoop

Directory of Open Access Journals (Sweden)

Wu Jun

2016-01-01

Full Text Available With the rapid development of information technology, the scientific research shows that the data mining and other information technology could be used in the design of new materials. It is explicit that Intelligent Materials research focuses on using physical and chemical principles combined with computer techniques such as Big Data, Cloud computing and Intelligent modeling and simulation to solve chemical problems. In this paper, based on the cluster based outlier algorithm as the main body, this paper discusses the definition New Materials research In the Hadoop cloud platform, and the parallel processing of Map-Reduce model. The performance this model of new material was established by using the method of Map-Reduction provided the basis for the performance optimization.

Materializing a responsive interior: designing minimum energy structures

DEFF Research Database (Denmark)

Mossé, Aurélie; Kofod, Guggi; Ramsgaard Thomsen, Mette

2011-01-01

This paper discusses a series of design-led experiments investigating future possibilities for architectural materialization relying on minimum energy structures as an example of adaptive structure. The structures have been made as laminates of elastic membrane under high tension with flexible...... (Lendlein, Kelch 2002) or light (van Oosten, Bastiaansen et al. 2009). All in all, this approach could form a whole new design paradigm, in which efficient 2D-manufacturing can lead to highly flexible, low weight and adaptable 3D-structures. This is illustrated by the design and manufacture of electro...

Materials by design

International Nuclear Information System (INIS)

Eberhardt, J.; Hay, P.J.; Carpenter, J.A. Jr.

1986-01-01

Major developments in materials characterization instrumentation over the past decade have helped significantly to elucidate complex processes and phenomena connected with the microstructure of materials and interfacial interactions. Equally remarkable advances in theoretical models and computer technology also have been taking place during this period. These latter now permit, for example, in selected cases the computation of material structures and bonding and the prediction of some material properties. Two assessments of the state of the art of instrumental techniques and theoretical methods for the study of material structures and properties have recently been conducted. This paper discusses aspects from these assessments of computational theoretical methods apply to materials

The changing role of nuclear materials accounting

International Nuclear Information System (INIS)

Gibbs, P.W.

1995-01-01

Nuclear materials accounting and accounting systems at what have been DOE Production sites are evolving into management decision support tools. As the sites are moving into the mode of making decisions on how to disposition complex and varied nuclear material holdings, the need for complete and many times different information has never been greater. The artificial boundaries that have historically been established between what belongs in the classic material control and accountability (MC and A) records versus what goes into the financial, radiological control, waste, or decommissioning and decontamination records are being challenged. In addition, the tools historically used to put material into different categories such as scrap codes, composition codes, etc. have been found to be inadequate for the information needs of today. In order to be cost effective and even, more importantly to effectively manage -our inventories, the new information systems the authors design have to have the flexibility to serve many needs. In addition, those tasked with the responsibility of managing the inventories must also expand beyond the same artificial boundaries. This paper addresses some of the things occurring at the Savannah River Site to support the changing role of nuclear materials accounting

Materials, Designs and Standards Used in Ski-Boots for Alpine Skiing

Directory of Open Access Journals (Sweden)

Matteo Moncalero

2013-10-01

Full Text Available This review article reports the recent advances in the study, design and production of ski-boots for alpine skiing. An overview of the different designs and the materials used in ski-boot construction is provided giving particular emphasis to the effect of these parameters on the final performances and on the prevention of injuries. The use of specific materials for ski-boots dedicated to different disciplines (race skiing, mogul skiing, ski-mountaineering etc. has been correlated with the chemical and physical properties of the polymeric materials employed. A review of the scientific literature and the most interesting patents is also presented, correlating the results reported with the performances and industrial production of ski-boots. Suggestions for new studies and the use of advanced materials are also provided. A final section dedicated to the standards involved in ski-boot design completes this review article.

Materials Selection And Fabrication Practices For Food Processing Equipment Manufacturers In Uganda

Directory of Open Access Journals (Sweden)

John Baptist Kirabira

2017-08-01

Full Text Available The food processing industry is one of the fast-growing sub-sectors in Uganda. The industry which is majorly composed of medium and small scale firms depends on the locally developed food processing equipment. Due to lack of effective materials selection practices employed by the equipment manufacturers the materials normally selected for most designs are not the most appropriate ones hence compromising the quality of the equipment produced. This has not only led to poor quality food products due to contamination but could also turn out health hazardous to the consumers of the food products. This study involved the assessment of the current materials selection and fabrication procedures used by the food processing equipment manufacturers with a view of devising best practices that can be used to improve the quality of the food products processed by the locally fabricated equipment. Results of the study show that designers experience biasness and desire to minimize cost compromise the materials selection procedure. In addition to failing to choose the best material for a given application most equipment manufacturers are commonly fabricating equipment with inadequate surface finish and improper weldments. This hinders the equipments ability to meet food hygiene standards.

Designing Educative Curriculum Materials: A Theoretically and Empirically Driven Process

Science.gov (United States)

Davis, Elizabeth A.; Palincsar, Annemarie Sullivan; Arias, Anna Maria; Bismack, Amber Schultz; Marulis, Loren M.; Iwashyna, Stefanie K.

2014-01-01

In this article, the authors argue for a design process in the development of educative curriculum materials that is theoretically and empirically driven. Using a design-based research approach, they describe their design process for incorporating educative features intended to promote teacher learning into existing, high-quality curriculum…

FOREWORD: Computational methodologies for designing materials Computational methodologies for designing materials

Science.gov (United States)

Rahman, Talat S.

2009-02-01

It would be fair to say that in the past few decades, theory and computer modeling have played a major role in elucidating the microscopic factors that dictate the properties of functional novel materials. Together with advances in experimental techniques, theoretical methods are becoming increasingly capable of predicting properties of materials at different length scales, thereby bringing in sight the long-sought goal of designing material properties according to need. Advances in computer technology and their availability at a reasonable cost around the world have made tit all the more urgent to disseminate what is now known about these modern computational techniques. In this special issue on computational methodologies for materials by design we have tried to solicit articles from authors whose works collectively represent the microcosm of developments in the area. This turned out to be a difficult task for a variety of reasons, not the least of which is space limitation in this special issue. Nevertheless, we gathered twenty articles that represent some of the important directions in which theory and modeling are proceeding in the general effort to capture the ability to produce materials by design. The majority of papers presented here focus on technique developments that are expected to uncover further the fundamental processes responsible for material properties, and for their growth modes and morphological evolutions. As for material properties, some of the articles here address the challenges that continue to emerge from attempts at accurate descriptions of magnetic properties, of electronically excited states, and of sparse matter, all of which demand new looks at density functional theory (DFT). I should hasten to add that much of the success in accurate computational modeling of materials emanates from the remarkable predictive power of DFT, without which we would not be able to place the subject on firm theoretical grounds. As we know and will also

Designing towards the Unknown: Engaging with Material and Aesthetic Uncertainty

Directory of Open Access Journals (Sweden)

Danielle Wilde

2017-12-01

Full Text Available New materials with new capabilities demand new ways of approaching design. Destabilising existing methods is crucial to develop new methods. Yet, radical destabilisation—where outcomes remain unknown long enough that new discoveries become possible—is not easy in technology design where complex interdisciplinary teams with time and resource constraints need to deliver concrete outcomes on schedule. The Poetic Kinaesthetic Interface project (PKI engages with this problematic directly. In PKI we use unfolding processes—informed by participatory, speculative and critical design—in emergent actions, to design towards unknown outcomes, using unknown materials. The impossibility of this task is proving as useful as it is disruptive. At its most potent, it is destabilising expectations, aesthetics and processes. Keeping the researchers, collaborators and participants in a state of unknowing, is opening the research potential to far-ranging possibilities. In this article we unpack the motivations driving the PKI project. We present our mixed-methodology, which entangles textile crafts, design interactions and materiality to shape an embodied enquiry. Our research outcomes are procedural and methodological. PKI brings together diverse human, non-human, known and unknown actors to discover where the emergent assemblages might lead. Our approach is re-invigorating—as it demands re-envisioning of—the design process.

Materials design data for reduced activation martensitic steel type EUROFER

Energy Technology Data Exchange (ETDEWEB)

Tavassoli, A.-A.F. E-mail: tavassoli@cea.fr; Alamo, A.; Bedel, L.; Forest, L.; Gentzbittel, J.-M.; Rensman, J.-W.; Diegele, E.; Lindau, R.; Schirra, M.; Schmitt, R.; Schneider, H.C.; Petersen, C.; Lancha, A.-M.; Fernandez, P.; Filacchioni, G.; Maday, M.F.; Mergia, K.; Boukos, N.; Baluc,; Spaetig, P.; Alves, E.; Lucon, E

2004-08-01

Materials design limits derived so far from the data generated in Europe for the reduced activation ferritic/martensitic (RAFM) steel type Eurofer are presented. These data address the short-term needs of the ITER Test Blanket Modules and a DEMOnstration fusion reactor. Products tested include plates, bars, tubes, TIG and EB welds, as well as powder consolidated blocks and solid-solid HIP joints. Effects of thermal ageing and low dose neutron irradiation are also included. Results are sorted and screened according to design code requirements before being introduced in reference databases. From the physical properties databases, variations of magnetic properties, modulus of elasticity, density, thermal conductivity, thermal diffusivity, specific heat, mean and instantaneous linear coefficients of thermal expansion versus temperature are derived. From the tensile and creep properties databases design allowable stresses are derived. From the instrumented Charpy impact and fracture toughness databases, ductile to brittle transition temperature, toughness and behavior of materials in different fracture modes are evaluated. From the fatigue database, total strain range versus number of cycles to failure curves are plotted and used to derive fatigue design curves. Cyclic curves are also derived and compared with monotonic hardening curves. Finally, irradiated and aged materials data are compared to ensure that the safety margins incorporated in unirradiated design limits are not exceeded.

Racial and Social Class Differences in How Parents Respond to Inadequate Achievement: Consequences for Children's Future Achievement.

Science.gov (United States)

Robinson, Keith; Harris, Angel L

2013-12-01

Despite numerous studies on parental involvement in children's academic schooling, there is a dearth of knowledge on how parents respond specifically to inadequate academic performance. This study examines whether 1) racial differences exist in parenting philosophy for addressing inadequate achievement, 2) social class has implications for parenting philosophy, and 3) parents' philosophies are consequential for children's academic achievement. Using data from the Child Development Supplement (N=1041) to the Panel Study of Income Dynamics, we sort parents into two categories-those whose parenting repertoires for addressing poor achievement include punitive responses and those whose repertoires do not. We then determine whether racial differences exist between these categories and how various responses within the aforementioned categories are related to students' academic achievement. The findings show that white and black parents have markedly different philosophies on how to respond to inadequate performance, and these differences appear to impact children's achievement in dramatically different ways. Educators and policy makers should pay particular attention to how parents respond to inadequate achievement as imploring parents of inadequately performing students to be more involved without providing them with some guidance might exacerbate the problem.

Hybrid materials science: a promised land for the integrative design of multifunctional materials

Science.gov (United States)

Nicole, Lionel; Laberty-Robert, Christel; Rozes, Laurence; Sanchez, Clément

2014-05-01

For more than 5000 years, organic-inorganic composite materials created by men via skill and serendipity have been part of human culture and customs. The concept of ``hybrid organic-inorganic'' nanocomposites exploded in the second half of the 20th century with the expansion of the so-called ``chimie douce'' which led to many collaborations between a large set of chemists, physicists and biologists. Consequently, the scientific melting pot of these very different scientific communities created a new pluridisciplinary school of thought. Today, the tremendous effort of basic research performed in the last twenty years allows tailor-made multifunctional hybrid materials with perfect control over composition, structure and shape. Some of these hybrid materials have already entered the industrial market. Many tailor-made multiscale hybrids are increasingly impacting numerous fields of applications: optics, catalysis, energy, environment, nanomedicine, etc. In the present feature article, we emphasize several fundamental and applied aspects of the hybrid materials field: bioreplication, mesostructured thin films, Lego-like chemistry designed hybrid nanocomposites, and advanced hybrid materials for energy. Finally, a few commercial applications of hybrid materials will be presented.

Hybrid materials science: a promised land for the integrative design of multifunctional materials.

Science.gov (United States)

Nicole, Lionel; Laberty-Robert, Christel; Rozes, Laurence; Sanchez, Clément

2014-06-21

For more than 5000 years, organic-inorganic composite materials created by men via skill and serendipity have been part of human culture and customs. The concept of "hybrid organic-inorganic" nanocomposites exploded in the second half of the 20th century with the expansion of the so-called "chimie douce" which led to many collaborations between a large set of chemists, physicists and biologists. Consequently, the scientific melting pot of these very different scientific communities created a new pluridisciplinary school of thought. Today, the tremendous effort of basic research performed in the last twenty years allows tailor-made multifunctional hybrid materials with perfect control over composition, structure and shape. Some of these hybrid materials have already entered the industrial market. Many tailor-made multiscale hybrids are increasingly impacting numerous fields of applications: optics, catalysis, energy, environment, nanomedicine, etc. In the present feature article, we emphasize several fundamental and applied aspects of the hybrid materials field: bioreplication, mesostructured thin films, Lego-like chemistry designed hybrid nanocomposites, and advanced hybrid materials for energy. Finally, a few commercial applications of hybrid materials will be presented.

High-temperature mechanical and material design for SiC composites

International Nuclear Information System (INIS)

Ghoniem, N.M.

1992-01-01

Silicon Carbide (SiC) fiber reinforced composites (FRC's) are strong potential candidate structural and high heat flux materials for fusion reactors. During this past decade, they have been vigorously developed for use in aerospace and transportation applications. Recent fusion reactor systems studies, such as ARIES, have concluded that further development of SiC composites will result in significant safety, operational, and waste disposal advantages for fusion systems. A concise discussion of the main material and design issues related to the use of SiC FRC's as structural materials in future fusion systems is given in this paper. The status of material processing of SiC/SiC composites is first reviewed. The advantages and shortcomings of the leading processing technology, known as Chemical Vapor Infiltration are particularly highlighted. A brief outline of the design-relevant physical, mechanical, and radiation data base is then presented. SiC/SiC FRC's possess the advantage of increased apparent toughness under mechanical loading conditions. This increased toughness, however, is associated with the nucleation and propagation of small crack patterns in the structure. Design approaches and failure criteria under these conditions are discussed

Inadequate control of world's radioactive sources

International Nuclear Information System (INIS)

2002-01-01

The radioactive materials needed to build a 'dirty bomb' can be found in almost any country in the world, and more than 100 countries may have inadequate control and monitoring programs necessary to prevent or even detect the theft of these materials. The IAEA points out that while radioactive sources number in the millions, only a small percentage have enough strength to cause serious radiological harm. It is these powerful sources that need to be focused on as a priority. In a significant recent development, the IAEA, working in collaboration with the United States Department of Energy (DOE) and the Russian Federation's Ministry for Atomic Energy (MINATOM), have established a tripartite working group on 'Securing and Managing Radioactive Sources'. Through its program to help countries improve their national infrastructures for radiation safety and security, the IAEA has found that more than 100 countries may have no minimum infrastructure in place to properly control radiation sources. However, many IAEA Member States - in Africa, Asia, Latin America, and Europe - are making progress through an IAEA project to strengthen their capabilities to control and regulate radioactive sources. The IAEA is also concerned about the over 50 countries that are not IAEA Member States (there are 134), as they do not benefit from IAEA assistance and are likely to have no regulatory infrastructure. The IAEA has been active in lending its expertise to search out and secure orphaned sources in several countries. More than 70 States have joined with the IAEA to collect and share information on trafficking incidents and other unauthorized movements of radioactive sources and other radioactive materials. The IAEA and its Member States are working hard to raise levels of radiation safety and security, especially focusing on countries known to have urgent needs. The IAEA has taken the leading role in the United Nations system in establishing standards of safety, the most significant of

Conceptual Design Report for the Irradiated Materials Characterization Laboratory (IMCL)

Energy Technology Data Exchange (ETDEWEB)

Stephanie Austad

2010-06-01

This document describes the design at a conceptual level for the Irradiated Materials Characterization Laboratory (IMCL) to be located at the Materials and Fuels Complex (MFC) at the Idaho National Laboratory (INL). The IMCL is an 11,000-ft2, Hazard Category-2 nuclear facility that is designed for use as a state of the-art nuclear facility for the purpose of hands-on and remote handling, characterization, and examination of irradiated and nonirradiated nuclear material samples. The IMCL will accommodate a series of future, modular, and reconfigurable instrument enclosures or caves. To provide a bounding design basis envelope for the facility-provided space and infrastructure, an instrument enclosure or cave configuration was developed and is described in some detail. However, the future instrument enclosures may be modular, integral with the instrument, or reconfigurable to enable various characterization environments to be configured as changes in demand occur. They are not provided as part of the facility.

Design and fabrication of irradiation testing capsule for research reactor materials

International Nuclear Information System (INIS)

Yang, Seong Woo; Kim, Bong Goo; Park, Seung Jae; Cho, Man Soon; Choo, Kee Nam; Oh, Jong Myeong; Choi, Myeong Hwan; Lee, Byung Chul; Kang, Suk Hoon; Kim, Dae Jong; Chun, Young Bum; Kim, Tae Kyu

2012-01-01

Recently, the demand of research reactors is increasing because there are many ageing research reactors in the world. Also, the production of radioisotope related with the medical purpose is very important. Korea Atomic Energy Research Institute (KAERI) is designing and licensing for Jordan Research and Training Reactor (JRTR) and new type research reactor for export which will be constructed in Amman, Jordan and Busan, Korea, respectively. Thus, It is expected that more research reactors will be designed and constructed by KAERI. To design the research reactor, the irradiation performance and behavior of core structure material are necessary. However, the irradiation behavior of these materials is not yet investigated. Therefore, the irradiation performance must be verified by irradiation test. 11M 20K and 11M 21K irradiation capsules were designed and fabricated to conduct the irradiation test for some candidate core materials, Zircaloy 4, beryllium, and graphite, at HANARO. In this paper, the design and fabrication features of 11M 20K and 11M 21K were discussed

Design and fabrication of irradiation testing capsule for research reactor materials

Energy Technology Data Exchange (ETDEWEB)

Yang, Seong Woo; Kim, Bong Goo; Park, Seung Jae; Cho, Man Soon; Choo, Kee Nam; Oh, Jong Myeong; Choi, Myeong Hwan; Lee, Byung Chul; Kang, Suk Hoon; Kim, Dae Jong; Chun, Young Bum; Kim, Tae Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-10-15

Recently, the demand of research reactors is increasing because there are many ageing research reactors in the world. Also, the production of radioisotope related with the medical purpose is very important. Korea Atomic Energy Research Institute (KAERI) is designing and licensing for Jordan Research and Training Reactor (JRTR) and new type research reactor for export which will be constructed in Amman, Jordan and Busan, Korea, respectively. Thus, It is expected that more research reactors will be designed and constructed by KAERI. To design the research reactor, the irradiation performance and behavior of core structure material are necessary. However, the irradiation behavior of these materials is not yet investigated. Therefore, the irradiation performance must be verified by irradiation test. 11M 20K and 11M 21K irradiation capsules were designed and fabricated to conduct the irradiation test for some candidate core materials, Zircaloy 4, beryllium, and graphite, at HANARO. In this paper, the design and fabrication features of 11M 20K and 11M 21K were discussed.

Design of a materials testing experiment for the INTOR

International Nuclear Information System (INIS)

Vogel, M.A.; Opperman, E.K.

1981-01-01

The United States, Japan, USSR and the European community are jointly participating in the design of an International Tokamak Reactor called INTOR. In support of the US contribution to the INTOR design, the features of an experiment for bulk neutron irradiation damage studies were developed. It is anticipated that materials testing will be an important part of the programmatic mission of INTOR and consequently the requirements for materials testing in INTOR must be identified early in the reactor design to insure compatibility. The design features of the experiment, called a Channel Test, are given in this paper. The major components of the channel test are the water cooled heat sink (channel module) and the specimen capsule. The temperature within each of the 153 specimen capsules is predetermined by engineering the thermal barrier between the specimen capsule and heat sink. Individual capsules can be independently accessed and are designed to operate at a predetermined temperature within the range of 50 to 700 0 C. The total irradiation volume within a single channel test is 45 liters. Features of the channel test that result in experimental versatility and simplified remote access and handling are discussed

Predicting Patients with Inadequate 24- or 48-Hour Urine Collections at Time of Metabolic Stone Evaluation.

Science.gov (United States)

McGuire, Barry B; Bhanji, Yasin; Sharma, Vidit; Frainey, Brendan T; McClean, Megan; Dong, Caroline; Rimar, Kalen; Perry, Kent T; Nadler, Robert B

2015-06-01

We aimed to understand the characteristics of patients who are less likely to submit adequate urine collections at metabolic stone evaluation. Inadequate urine collection was defined using two definitions: (1) Reference ranges for 24-hour creatinine/kilogram (Cr/24) and (2) discrepancy in total 24-hour urine Cr between 24-hour urine collections. There were 1502 patients with ≥1 kidney stone between 1998 and 2014 who performed a 24- or 48-hour urine collection at Northwestern Memorial Hospital and who were identified retrospectively. Multivariate analysis was performed to analyze predictor variables for adequate urine collection. A total of 2852 urine collections were analyzed. Mean age for males was 54.4 years (range 17-86), and for females was 50.2 years (range 8-90). One patient in the study was younger than 17 years old. (1) Analysis based on the Cr 24/kg definition: There were 50.7% of patients who supplied an inadequate sample. Females were nearly 50% less likely to supply an adequate sample compared with men, Pcollections were achieved in 82.8%, 66.9%, 51.7%, 38.5%, and 26.4% of patients, respectively. Statistical significance was observed based on differences of ≥40%, and this was defined as the threshold for an inadequate sample. Female sex (OR 0.73 [0.54-0.98], P=0.037) predicted supplying inadequate samples. Adequate collections were more likely to be received on a Sunday (OR 1.6 [1.03-2.58], P=0.038) and by sedentary workers (OR 2.3 [1.12-4.72], P=0.023). Urine collections from patients during metabolic evaluation for nephrolithiasis may be considered inadequate based on two commonly used clinical definitions. This may have therapeutic or economic ramifications and the propensity for females to supply inadequate samples should be investigated further.

MDTS: automatic complex materials design using Monte Carlo tree search

Science.gov (United States)

Dieb, Thaer M.; Ju, Shenghong; Yoshizoe, Kazuki; Hou, Zhufeng; Shiomi, Junichiro; Tsuda, Koji

2017-12-01

Complex materials design is often represented as a black-box combinatorial optimization problem. In this paper, we present a novel python library called MDTS (Materials Design using Tree Search). Our algorithm employs a Monte Carlo tree search approach, which has shown exceptional performance in computer Go game. Unlike evolutionary algorithms that require user intervention to set parameters appropriately, MDTS has no tuning parameters and works autonomously in various problems. In comparison to a Bayesian optimization package, our algorithm showed competitive search efficiency and superior scalability. We succeeded in designing large Silicon-Germanium (Si-Ge) alloy structures that Bayesian optimization could not deal with due to excessive computational cost. MDTS is available at https://github.com/tsudalab/MDTS.

Design and construction of the Fuels and Materials Examination Facility

International Nuclear Information System (INIS)

Burgess, C.A.

1979-01-01

Final design is more than 85 percent complete on the Fuels and Materials Examination Facility, the facility for post-irradiation examination of the fuels and materials tests irradiated in the FFTF and for fuel process development, experimental test pin fabrication and supporting storage, assay, and analytical chemistry functions. The overall facility is generally described with specific information given on some of the design features. Construction has been initiated and more than 10% of the construction contracts have been awarded on a fixed price basis

Advanced Energy Storage Devices: Basic Principles, Analytical Methods, and Rational Materials Design

Science.gov (United States)

Liu, Jilei; Wang, Jin; Xu, Chaohe; Li, Chunzhong; Lin, Jianyi

2017-01-01

Abstract Tremendous efforts have been dedicated into the development of high‐performance energy storage devices with nanoscale design and hybrid approaches. The boundary between the electrochemical capacitors and batteries becomes less distinctive. The same material may display capacitive or battery‐like behavior depending on the electrode design and the charge storage guest ions. Therefore, the underlying mechanisms and the electrochemical processes occurring upon charge storage may be confusing for researchers who are new to the field as well as some of the chemists and material scientists already in the field. This review provides fundamentals of the similarities and differences between electrochemical capacitors and batteries from kinetic and material point of view. Basic techniques and analysis methods to distinguish the capacitive and battery‐like behavior are discussed. Furthermore, guidelines for material selection, the state‐of‐the‐art materials, and the electrode design rules to advanced electrode are proposed. PMID:29375964

Implications of material selection on the design of packaging machinery.

Science.gov (United States)

Merritt, J P

2009-01-01

Material selection has significant implications on the design and cost of horizontal-form-fill-seal packaging machinery. To avoid excessive costs, machine redesigns and project delays, material selection must be reconciled early in the project and revisited throughout the construction of the machine.

Performance evaluation of seal coat materials and designs.

Science.gov (United States)

2011-01-01

"This project presents an evaluation of seal coat materials and design method. The primary objectives of this research are 1) to evaluate seal coat performance : from various combinations of aggregates and emulsions in terms of aggregate loss; 2) to ...

European DEMO divertor target: Operational requirements and material-design interface

Directory of Open Access Journals (Sweden)

J.H. You

2016-12-01

Full Text Available Recently, an integrated program of conceptual design activities for the European DEMO reactor was launched in the framework of the EUROfusion Consortium, where reliable power handling capability was identified as one of the most critical scientific as well as technological challenges for a DEMO reactor. The divertor is the key in-vessel plasma-facing component being in charge of power exhaust and removal of impurity particles. The DEMO divertor target will have to withstand extreme thermal loads where the local peak heat flux is expected to reach up to 20 MW/m2 during slow transient events in DEMO. To assure sufficient heat removal capability of the divertor target against normal and transient operational scenarios under expected cumulative neutron dose of up to 13 dpa is one of the fundamental engineering challenges imposed on target design. To develop the design of the DEMO divertor and related technologies, an R&D work package ‘Divertor’ has been set up in this consortium. The subproject ‘Target Development’ is devoted to the development of the conceptual design and the core technologies of the plasma-facing target. Devising and implementing novel structural heat sink materials (e.g. W/Cu composites to advanced target design concepts is one of the major objectives of this subproject. In this paper, the underlying design requirements imposed by the envisaged power exhaust goal and the prominent material-design interface issues are discussed. In addition, the candidate design concepts being currently considered are presented together with the related material issues. Finally, the first results achieved so far are presented.

Materials interaction tests to identify base and coating materials for an enhanced in-vessel core catcher design

Energy Technology Data Exchange (ETDEWEB)

Rempe, J.L.; Knudson, D.L.; Condie, K.G.; Swank, W.D. [Idaho National Engineering and Environmental Laboratory, Idaho Falls ID (United States); Cheung, F.B. [Pennsylvania State University, Department of Mechanical and Nuclear Engineering, University Park PA (United States); Suh, K.Y. [Seoul National University, Department of Nuclear Engineering, Seoul (Korea, Republic of); Kim, S.B. [Korea Atomic Energy Research Institute, Severe Accident Research Project, Taejon (Korea, Republic of)

2004-07-01

An enhanced in-vessel core catcher is being designed and evaluated, it must ensure In-Vessel Retention of core materials that may relocate under severe accident conditions in advanced reactors. To reduce cost and simplify manufacture and installation, this new core catcher design consists of several interlocking sections that are machined to fit together when inserted into the lower head. If needed, the core catcher can be manufactured with holes to accommodate lower head penetrations. Each section of the core catcher consists of two material layers with an option to add a third layer (if deemed necessary): a base material, which has the capability to support and contain the mass of core materials that may relocate during a severe accident; an insulating oxide coating material on top of the base material, which resists interactions with high-temperature core materials; and an optional coating on the bottom side of the base material to prevent any potential oxidation of the base material during the lifetime of the reactor. Initial evaluations suggest that a thermally-sprayed oxide material is the most promising candidate insulator coating for a core catcher. Tests suggest that 2 coatings can provide adequate protection to a stainless steel core catcher: -) a 500 {mu}m thick zirconium dioxide coating over a 100-200 {mu}m Inconel 718 bond coating, and -) a 500 {mu}m thick magnesium zirconate coating.

Inadequate cerebral oxygen delivery and central fatigue during strenuous exercise

DEFF Research Database (Denmark)

Nybo, Lars; Rasmussen, Peter

2007-01-01

Under resting conditions, the brain is protected against hypoxia because cerebral blood flow increases when the arterial oxygen tension becomes low. However, during strenuous exercise, hyperventilation lowers the arterial carbon dioxide tension and blunts the increase in cerebral blood flow, which...... can lead to an inadequate oxygen delivery to the brain and contribute to the development of fatigue....

An introduction to the integrated design of surface mine haul roads

Energy Technology Data Exchange (ETDEWEB)

Thompson, R.J.; Visser, A.T. [University of Pretoria, Pretoria (South Africa). Dept. of Mining Engineering

1997-12-01

The world-wide expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling layloads in excess of 160 t. Typical axle loads ranging from 110 t to 170 t are applied to haul roads that have been, at best, empirically designed on the premise of `satisfactory` or `failed`, both in terms of structure and function of the road. The use of these empirical pavement design techniques will prove inadequate when high axle loads are encountered. Not only will the maintenance costs of existing haul roads of inadequate thickness increase, but vehicle operating and maintenance costs will also increase prohibitively. Under these conditions there is thus a clearly defined need for improved construction and management techniques for flexible mine haulage roads, appropriate for the wheel loads of vehicles now in use. The aim of this paper is to introduce developments in haul road structural, functional and maintenance design and management which overcome the limitations associated with the previously empirical design techniques and to show how these developments are combined into an integrated design strategy combining construction techniques, available material and road maintenance equipment with hauler choice to realise a reduction in haulage and road maintenance costs. Future contributions will enumerate on the fundamental haul road structural, functional and maintenance design and management research from which these developments originated. 7 refs., 5 figs., 2 tabs.

Results of salvage radiotherapy after inadequate surgery in invasive cervical carcinoma patients: A retrospective analysis

International Nuclear Information System (INIS)

Saibishkumar, Elantholi P.; Patel, Firuza D.; Ghoshal, Sushmita; Kumar, Vinay; Karunanidhi, Gunaseelan; Sharma, Suresh C.

2005-01-01

Purpose: To evaluate the results of salvage radiotherapy (RT) after inadequate surgery in patients with invasive carcinoma of the cervix. Methods and Materials: Between 1996 and 2001, 105 invasive cervical carcinoma patients were treated at our center with external beam RT with or without intracavitary RT after having undergone total/subtotal hysterectomy at outside institutions. Results: The median follow-up was 34 months. The gap between surgery and RT was 23-198 days (median, 80). Clinically visible residual disease was present in 81 patients (77.1%). Total hysterectomy had been done in 82 patients (78%) and subtotal hysterectomy in 23 patients (22%). The 5-year overall survival, disease-free survival, and pelvic control rates of all patients were 55.2%, 53.3%, and 72.4%, respectively. On univariate analysis, older age, total hysterectomy, hemoglobin level >10 g% before RT, nonsquamous histologic type, use of intracavitary RT, a shorter gap between surgery and RT, and the absence of, or a small volume of, residual disease favorably affected the outcome. The 5-year actuarial rate of late toxicity (Radiation Therapy Oncology Group Criteria) was 19% in the rectum, 4.8% in the bladder, 24.8% in the skin, and 14.3% in the small intestine. Conclusions: Inadequate and inappropriate surgery in invasive cervical cancer with resulting gross residual disease is common in India. Factors such as the use of intracavitary RT, the correction of anemia, and a shorter gap between surgery and RT will enable postoperative RT to achieve acceptable results with minimal morbidity

Mould growth on building materials

DEFF Research Database (Denmark)

Fog Nielsen, K.

Mould growth in buildings is associated with adverse health effects among the occupants of the building. However actual growth only occurs in damp and water-damaged materials, and is an increasing problem in Denmark, due to less robust constructions, inadequate maintenance, and too little...

Predicting the microstructure-dependent mechanical performance of materials for early-stage design

International Nuclear Information System (INIS)

Dimiduk, D.M.; Uchic, M.D.; Parathasarathy, T.A.; Rao, S.I.; Choi, Y.-S.

2004-01-01

A description is offered of a simulation and testing methodology for structural materials that incorporates the influence of the local, microscopic and submicroscopic heterogeneous nature of material properties directly into design procedures. The new methodology builds upon a multitude of rapid microstructural and property assessments of selected local regions of a material (i.e. single-crystal regions, defected regions, grain aggregates, etc.), perhaps from a fully-processed component, or from materials specifically prepared to represent selected aspects of the full-scale process. The results from these assessments are used to define parameters within a hierarchy of mathematical and numerical representations of the material, and together in turn these may be used in design performance simulation codes to predict the intrinsic response of larger-scale structures. Further, the methodology may be used to anticipate the effects of defects on the performance of the full-scale structure. Most steps of this alternative design and test methodology are amenable to automation, and the methodology as a whole will reduce the number of iterative large-scale cycles required to qualify a material's suitability for structural service; thus, the new method is a framework for accelerating the development of structural materials

Inadequate Evidence for Multiple Intelligences, Mozart Effect, and Emotional Intelligence Theories

Science.gov (United States)

Waterhouse, Lynn

2006-01-01

I (Waterhouse, 2006) argued that, because multiple intelligences, the Mozart effect, and emotional intelligence theories have inadequate empirical support and are not consistent with cognitive neuroscience findings, these theories should not be applied in education. Proponents countered that their theories had sufficient empirical support, were…

Numerical study and design optimization of electromagnetic energy harvesters integrated with flexible magnetic materials

Energy Technology Data Exchange (ETDEWEB)

Yoon, Sang Won [Hanyang University, Seoul (Korea, Republic of)

2017-05-15

This study presents a new design of an electromagnetic energy harvester integrated with a soft magnetic material. The harvester design optimizes the magnetic material characteristics and the size of a rectangular permanent magnet. The design employs a complete magnetic circuit made of (1) a thin-film soft magnetic material that facilitates a flexible but highly (magnetically) permeable beam and (2) an optimally-sized magnet that maximizes the harvester performance. The design is demonstrated to reduce magnetic flux leakage, and thus considerably enhances both magnetic flux density (B) and its change by time (dB/dt), which both influence harvester performance. The improvement in harvester performances strongly depends on critical design parameters, especially, the magnet size and characteristics of magnetic materials, including permeability, stiffness, and thickness. The analyses conclude that recently-introduced nanomaterials (having ultrahigh magnetic permeability) can potentially innovate harvester performances. However, the performance may be degraded without design optimization. Once optimized, the integrated nanomaterials facilitate a significant improvement compared with a conventional design without integrated magnetic materials.

Numerical study and design optimization of electromagnetic energy harvesters integrated with flexible magnetic materials

International Nuclear Information System (INIS)

Yoon, Sang Won

2017-01-01

This study presents a new design of an electromagnetic energy harvester integrated with a soft magnetic material. The harvester design optimizes the magnetic material characteristics and the size of a rectangular permanent magnet. The design employs a complete magnetic circuit made of (1) a thin-film soft magnetic material that facilitates a flexible but highly (magnetically) permeable beam and (2) an optimally-sized magnet that maximizes the harvester performance. The design is demonstrated to reduce magnetic flux leakage, and thus considerably enhances both magnetic flux density (B) and its change by time (dB/dt), which both influence harvester performance. The improvement in harvester performances strongly depends on critical design parameters, especially, the magnet size and characteristics of magnetic materials, including permeability, stiffness, and thickness. The analyses conclude that recently-introduced nanomaterials (having ultrahigh magnetic permeability) can potentially innovate harvester performances. However, the performance may be degraded without design optimization. Once optimized, the integrated nanomaterials facilitate a significant improvement compared with a conventional design without integrated magnetic materials.

Electron work function-a promising guiding parameter for material design.

Science.gov (United States)

Lu, Hao; Liu, Ziran; Yan, Xianguo; Li, Dongyang; Parent, Leo; Tian, Harry

2016-04-14

Using nickel added X70 steel as a sample material, we demonstrate that electron work function (EWF), which largely reflects the electron behavior of materials, could be used as a guide parameter for material modification or design. Adding Ni having a higher electron work function to X70 steel brings more "free" electrons to the steel, leading to increased overall work function, accompanied with enhanced e(-)-nuclei interactions or higher atomic bond strength. Young's modulus and hardness increase correspondingly. However, the free electron density and work function decrease as the Ni content is continuously increased, accompanied with the formation of a second phase, FeNi3, which is softer with a lower work function. The decrease in the overall work function corresponds to deterioration of the mechanical strength of the steel. It is expected that EWF, a simple but fundamental parameter, may lead to new methodologies or supplementary approaches for metallic materials design or tailoring on a feasible electronic base.

Accelerating the design of biomimetic materials by integrating RNA-seq with proteomics and materials science.

Science.gov (United States)

Guerette, Paul A; Hoon, Shawn; Seow, Yiqi; Raida, Manfred; Masic, Admir; Wong, Fong T; Ho, Vincent H B; Kong, Kiat Whye; Demirel, Melik C; Pena-Francesch, Abdon; Amini, Shahrouz; Tay, Gavin Z; Ding, Dawei; Miserez, Ali

2013-10-01

Efforts to engineer new materials inspired by biological structures are hampered by the lack of genomic data from many model organisms studied in biomimetic research. Here we show that biomimetic engineering can be accelerated by integrating high-throughput RNA-seq with proteomics and advanced materials characterization. This approach can be applied to a broad range of systems, as we illustrate by investigating diverse high-performance biological materials involved in embryo protection, adhesion and predation. In one example, we rapidly engineer recombinant squid sucker ring teeth proteins into a range of structural and functional materials, including nanopatterned surfaces and photo-cross-linked films that exceed the mechanical properties of most natural and synthetic polymers. Integrating RNA-seq with proteomics and materials science facilitates the molecular characterization of natural materials and the effective translation of their molecular designs into a wide range of bio-inspired materials.

Hartree-fock-slater method for materials science the DV-X alpha method for design and characterization of materials

CERN Document Server

Adachi, H; Kawai, J

2006-01-01

Molecular-orbital calculations for materials design such as alloys, ceramics, and coordination compounds are now possible for experimentalists. Molecuar-orbital calculations for the interpretation of chemical effect of spectra are also possible for experimentalists. The most suitable molecular-orbital calculation method for these purpose is the DV-Xa method, which is robust in such a way that the calculation converges to a result even if the structure of the molecule or solid is impossible in the pressure and temperature ranges on earth. This book specially addresses the methods to design novel materials and to predict the spectralline shape of unknown materials using the DV-Xa molecular-orbital method, but is also useful for those who want to calculate electronic structures of materials using any kind of method.

Creativity and innovations in ELT materials development looking beyond the current design

CERN Document Server

Bao, Dat

2018-01-01

This book challenges current practices in ELT materials design in order to transform coursebook quality. It proposes ways to improve task design through resources such as drama, poetry, literature and online resources; and it maps out a number of unusual connections between theory and practice in the field of ELT materials development.

Construction of irradiated material examination facility-basic design

International Nuclear Information System (INIS)

Ro, Seung Gy; Kim, Eun Ka; Hong, Gye Won; Herr, Young Hoi; Hong, Kwon Pyo; Lee, Myeong Han; Baik, Sang Youl; Choo, Yong Sun; Baik, Seung Je

1989-02-01

The basic design of the hot cell facility which has the main purpose of doing mechanical and physical property tests of irradiated materials, the examination process, and the annexed facility has been made. Also basic and detall designs for the underground excavation work have been performed. The project management and tasks required for the license application have been carried out in due course. The facility is expected to be completed by the end of 1992, if the budgetary support is sufficient. (Author)

Designs for the Evaluation of Teacher Training Materials. Report No. 2.

Science.gov (United States)

Okey, James R.; Ciesla, Jerome L.

This paper describes methods to assess the impact on students of a teacher using skills learned in a training program. Three designs for assessing the effects of teacher training materials are presented: time series design, equivalent time-samples design, and posttest-only control group design. Data obtained by classroom teachers while using the…

Probabilistic Fatigue Design of Composite Material for Wind Turbine Blades

DEFF Research Database (Denmark)

Toft, Henrik Stensgaard; Sørensen, John Dalsgaard

2011-01-01

In the present paper a probabilistic design approach to fatigue design of wind turbine blades is presented. The physical uncertainty on the fatigue strength for composite material is estimated using public available fatigue tests. Further, the model uncertainty on Miner rule for damage accumulation...

Materials design principles of ancient fish armour

Science.gov (United States)

Bruet, Benjamin J. F.; Song, Juha; Boyce, Mary C.; Ortiz, Christine

2008-09-01

Knowledge of the structure-property-function relationships of dermal scales of armoured fish could enable pathways to improved bioinspired human body armour, and may provide clues to the evolutionary origins of mineralized tissues. Here, we present a multiscale experimental and computational approach that reveals the materials design principles present within individual ganoid scales from the `living fossil' Polypterus senegalus. This fish belongs to the ancient family Polypteridae, which first appeared 96 million years ago during the Cretaceous period and still retains many of their characteristics. The mechanistic origins of penetration resistance (approximating a biting attack) were investigated and found to include the juxtaposition of multiple distinct reinforcing composite layers that each undergo their own unique deformation mechanisms, a unique spatial functional form of mechanical properties with regions of differing levels of gradation within and between material layers, and layers with an undetectable gradation, load-dependent effective material properties, circumferential surface cracking, orthogonal microcracking in laminated sublayers and geometrically corrugated junctions between layers.

Enclosed mechanical seal face design for brittle materials copyright

International Nuclear Information System (INIS)

Marsi, J.A.

1994-01-01

Metal carbides are widely used as seal face material due to their hardness and wear resistance. Silicon carbide (SiC) has excellent performance as a seal face material, but it is relatively brittle and may break due to accidental overloads outside the boundary of normal operating conditions. In mechanical seals for nuclear primary coolant pumps, the shattered SiC pieces can get into the reactor system and cause serious damage. The conventional method of containing an SiC seal face is to shrink-fit it in a holder, which may lead the seal designer to contend with unwanted seal face deflections. This paper presents a successful, tested design which does not rely on shrink-fits. 5 refs., 9 figs., 4 tabs

Special Features of Using Secondary Materials in the Interior Design of Public Dining Establishments

Science.gov (United States)

Kuznetsova, Irina; Hapchuk, Olena; Lukinov, Vitaly

2017-10-01

This article analyses the latest publications studying the use and practical application of secondary resources as raw materials in design. This analysis is based on the list of secondary resources and their applications in interior decoration. In particular, the interiors of public catering enterprises were analysed. Restaurants with different functional purposes that were classified into several categories with specific peculiarities of interior design were identified. This article presents and describes different types of public catering enterprises based on those categories. The interior design of a public catering enterprise is regarded as a considerably complex system. Different types of secondary materials were reviewed to identify the most frequently used materials for interior space design. This article describes the main peculiarities of the use of secondary materials and presents examples of their practical application. The function of secondary materials in the interior design of public catering enterprises were detected and reviewed. On the basis of the analysis, several directions for the practical application of our results in the field of public catering enterprise design were suggested.

Predictors of Inadequate Prenatal Care in Methamphetamine-Using Mothers in New Zealand and the United States

Science.gov (United States)

LaGasse, Linda L.; Wouldes, Trecia A.; Arria, Amelia M.; Wilcox, Tara; Derauf, Chris; Newman, Elana; Shah, Rizwan; Smith, Lynne M.; Neal, Charles R.; Huestis, Marilyn A.; DellaGrotta, Sheri; Lester, Barry M.

2013-01-01

This study compared patterns of prenatal care among mothers who used methamphetamine (MA) during pregnancy and non-using mothers in the US and New Zealand (NZ), and evaluated associations among maternal drug use, child protective services (CPS) referral, and inadequate prenatal care in both countries. The sample consisted of 182 mothers in the MA-Exposed and 196 in the Comparison groups in the US, and 107 mothers in the MA-Exposed and 112 in the Comparison groups in NZ. Positive toxicology results and/or maternal report of MA use during pregnancy were used to identify MA use. Information about sociodemographics, prenatal care and prenatal substance use was collected by maternal interview. MA-use during pregnancy is associated with lower socio-economic status, single marital status, and CPS referral in both NZ and the US. Compared to their non-using counterparts, MA-using mothers in the US had significantly higher rates of inadequate prenatal care. No association was found between inadequate care and MA-use in NZ. In the US, inadequate prenatal care was associated with CPS referral, but not in NZ. Referral to CPS for drug use only composed 40 % of all referrals in the US, but only 15 % of referrals in NZ. In our study population, prenatal MA-use and CPS referral eclipse maternal sociodemographics in explanatory power for inadequate prenatal care. The predominant effect of CPS referral in the US is especially interesting, and should encourage further research on whether the US policy of mandatory reporting discourages drug-using mothers from seeking antenatal care. PMID:22588827

CAE applications in a thermoforming mould design

International Nuclear Information System (INIS)

Marjuki, AR; Mohd Ghazali, FA; Ismail, N M; Sulaiman, S; Mohd Khairuddin, I; Majeed, Anwar P P A; Jaafar, AA; Basri, S; Mustapha, F

2016-01-01

Preparation of honeycomb layer is a critical step for successful fabrications of thermoformed based sandwiched structures. This paper deals with an initial investigation on the rapid manufacturing process of corrugated sheet with 120° dihedral angles. Time history of local displacements and thickness, assuming viscous dominated material model for a 1mm thick thermoformable material, was computed by using ANSYS ® Polyflow solver. The quality of formed surfaces was evaluated for selection of mould geometry and assessment of two common variants of thermoforming process. Inadequate mesh refinement of a membrane elements produces satisfactorily detailing and incomplete forming. A perfectly uniform material distribution was predicted using drape forming process. However, the geometrical properties of vacuum formed part are poorly distributed and difficult to control with increasing inflation volumes. Details of the discrepancies and the contributions of the CAE tool to complement traditional trial and error methodology in the process and design development are discussed. (paper)

Road Materials and Pavement Design volume 17(2)

CSIR Research Space (South Africa)

De Beer, Morris

2016-03-01

Full Text Available Materials and Pavement Design Volume 17, 2016 - Issue 2 Editorial Board Page ebi | Published online: 03 Oct 2016  http://dx.doi.org/10.1080/14680629.2016.1244475 Editors-in-Chief Hervé DI BENEDETTO - University of Lyon/ENTPE, Vaulx-en-Velin, France...

Robotic Materials Handling in Space: Mechanical Design of the Robot Operated Materials Processing System HitchHiker Experiment

Science.gov (United States)

Voellmer, George

1997-01-01

The Goddard Space Flight Center has developed the Robot Operated Materials Processing System (ROMPS) that flew aboard STS-64 in September, 1994. The ROMPS robot transported pallets containing wafers of different materials from their storage racks to a furnace for thermal processing. A system of tapered guides and compliant springs was designed to deal with the potential misalignments. The robot and all the sample pallets were locked down for launch and landing. The design of the passive lockdown system, and the interplay between it and the alignment system are presented.

The design and application of effective written instructional material: a review of published work.

Science.gov (United States)

Mayberry, John F

2007-09-01

This review will consider the evidence base for the format of educational material drawing on academic papers and the practice of the design industry. The core issues identified from the review are drawn together in guidelines for educational posters, text and web based material. The review deals with the design of written material both for use in leaflets and books as well as the impact of factors such as font type and size as well as colour on poster design. It sets these aspects of educational material within a research framework, which looks at impact on learning and subsequent change in practice. These issues are examined through a practical example of a poster designed for a regional gastroenterology meeting.

Inadequate pelvic radiographs: implications of not getting it right the first time.

Science.gov (United States)

Parker, S; Nagra, N S; Kulkarni, K; Pegrum, J; Barry, S; Hughes, R; Ghani, Y

2017-09-01

Introduction Pelvic radiography is a frequent investigation. European guidelines aim to ensure appropriate use and adequate quality. When initial images are inadequate, repeat radiographs are often required, which may have significant patient safety and economic implications. Objectives The study aimed to assess the adequacy of pelvic imaging across three orthopaedic centres, to identify causes for inadequate imaging and to establish the cost of inadequate imaging from financial and patient safety perspectives. Methods Pelvic radiographs were identified on Picture Archiving and Communication System software at three UK hospitals. Radiographs were assessed against European guidelines and indications for repeat imaging were analysed. Results A total of 1,531 sequential pelvic radiographs were reviewed. The mean age of patients was 60 years (range 5 months to 101 years). Of this total, 51.9% of images were suboptimal, with no significant difference across the three hospitals (P > 0.05). Hospital 3 repeated radiographs in 6.3% of cases, compare with 18.1% and 19.7% at hospitals 1 and 2, respectively (P > 0.05). Hospital 3 identified pathology missed on the initial radiograph in 1% of cases, compared with 5.4% and 5.5% at hospitals 1 and 2, respectively (P > 0.05). Out-of-hours imaging is associated with a higher rate of suboptimal quality (69.1%) compared with normal working hours (51.3%; P = 0.006). Adequacy rates vary with age (χ 2 = 43.62, P hours imaging.

Honeycomb technology materials, design, manufacturing, applications and testing

CERN Document Server

Bitzer, Tom

1997-01-01

Honeycomb Technology is a guide to honeycomb cores and honeycomb sandwich panels, from the manufacturing methods by which they are produced, to the different types of design, applications for usage and methods of testing the materials. It explains the different types of honeycomb cores available and provides tabulated data of their properties. The author has been involved in the testing and design of honeycomb cores and sandwich panels for nearly 30 years. Honeycomb Technology reflects this by emphasizing a `hands-on' approach and discusses procedures for designing sandwich panels, explaining the necessary equations. Also included is a section on how to design honeycomb energy absorbers and one full chapter discussing honeycomb core and sandwich panel testing. Honeycomb Technology will be of interest to engineers in the aircraft, aerospace and building industries. It will also be of great use to engineering students interested in basic sandwich panel design.

Design and selection of materials for sodium cooled fast reactors

International Nuclear Information System (INIS)

Chetal, S.C.

2011-01-01

Sodium cooled fast reactors are currently in operation, under construction or under design by a number of countries. The design of sodium cooled fast reactor is covered by French RCC - MR code and ASME code NH. The codes cover rules as regards to materials, design and construction. These codes do not cover the effect of irradiation and environment. Elevated temperature design criteria in nuclear codes are much stringent in comparison to non nuclear codes. Sodium corrosion is not an issue in selection of materials provided oxygen impurity in sodium is controlled for which excellent reactor operating experience is available. Austenitic stainless steels have remained the choice for the permanent structures of primary sodium system. Stabilized austenitic stainless steel are rejected because of poor operating experience and non inclusion in the design codes. Route for improved creep behaviour lies in compositional modifications in 316 class steel. However, the weldability needs to be ensured. For cold leg component is non creep regime, SS 304 class steel is favoured from overall economics. Enhanced fuel burn up can be realized by the use of 9-12%Cr 1%Mo class steel for the wrapper of MOX fuel design, and cladding and wrapper for metal fuel reactors. Minor compositional modifications of 20% cold worked 15Cr-15Ni class austenitic stainless steel will be a strong candidate for the cladding of MOX fuel design in the short term. Long term objective for the cladding will be to develop oxide dispersion strengthened steel. 9%Cr 1%Mo class steel (Gr 91) is an ideal choice for integrated once through sodium heated steam generators. One needs to incorporate operating experience from reactors and thermal power stations, industrial capability and R and D feedback in preparing the technical specifications for procurement of wrought products and welding consumables to ensure reliable operation of the components and systems over the design life. The paper highlights the design approach

A value-Oriented Approach to E-business Process Design

NARCIS (Netherlands)

Eder, J.; Gordijn, Jaap; Wieringa, Roelf J.; Missikoff, M.

Innovative e-commerce ideas have often floundered on an inadequate analysis of the expenses and benefits of the idea and an inadequate integration of the required e-business processes with other business processes. We present a requirements analysis and business process design approach that focuses

Estimating the global prevalence of inadequate zinc intake from national food balance sheets: effects of methodological assumptions.

Directory of Open Access Journals (Sweden)

K Ryan Wessells

Full Text Available The prevalence of inadequate zinc intake in a population can be estimated by comparing the zinc content of the food supply with the population's theoretical requirement for zinc. However, assumptions regarding the nutrient composition of foods, zinc requirements, and zinc absorption may affect prevalence estimates. These analyses were conducted to: (1 evaluate the effect of varying methodological assumptions on country-specific estimates of the prevalence of dietary zinc inadequacy and (2 generate a model considered to provide the best estimates.National food balance data were obtained from the Food and Agriculture Organization of the United Nations. Zinc and phytate contents of these foods were estimated from three nutrient composition databases. Zinc absorption was predicted using a mathematical model (Miller equation. Theoretical mean daily per capita physiological and dietary requirements for zinc were calculated using recommendations from the Food and Nutrition Board of the Institute of Medicine and the International Zinc Nutrition Consultative Group. The estimated global prevalence of inadequate zinc intake varied between 12-66%, depending on which methodological assumptions were applied. However, country-specific rank order of the estimated prevalence of inadequate intake was conserved across all models (r = 0.57-0.99, P<0.01. A "best-estimate" model, comprised of zinc and phytate data from a composite nutrient database and IZiNCG physiological requirements for absorbed zinc, estimated the global prevalence of inadequate zinc intake to be 17.3%.Given the multiple sources of uncertainty in this method, caution must be taken in the interpretation of the estimated prevalence figures. However, the results of all models indicate that inadequate zinc intake may be fairly common globally. Inferences regarding the relative likelihood of zinc deficiency as a public health problem in different countries can be drawn based on the country

Materials Process Design Branch. Work Unit Directive (WUD) 54

National Research Council Canada - National Science Library

LeClair, Steve

2002-01-01

The objectives of the Manufacturing Research WUD 54 are to 1) conduct in-house research to develop advanced materials process design/control technologies to enable more repeatable and affordable manufacturing capabilities and 2...

14 CFR 23.613 - Material strength properties and design values.

Science.gov (United States)

2010-01-01

... statistical basis. (b) Design values must be chosen to minimize the probability of structural failure due to... must be shown by selecting design values that ensure material strength with the following probability... failure of which would result in loss of structural integrity of the component; 99 percent probability...

Optimal Design of Gradient Materials and Bi-Level Optimization of Topology Using Targets (BOTT)

Science.gov (United States)

Garland, Anthony

The objective of this research is to understand the fundamental relationships necessary to develop a method to optimize both the topology and the internal gradient material distribution of a single object while meeting constraints and conflicting objectives. Functionally gradient material (FGM) objects possess continuous varying material properties throughout the object, and they allow an engineer to tailor individual regions of an object to have specific mechanical properties by locally modifying the internal material composition. A variety of techniques exists for topology optimization, and several methods exist for FGM optimization, but combining the two together is difficult. Understanding the relationship between topology and material gradient optimization enables the selection of an appropriate model and the development of algorithms, which allow engineers to design high-performance parts that better meet design objectives than optimized homogeneous material objects. For this research effort, topology optimization means finding the optimal connected structure with an optimal shape. FGM optimization means finding the optimal macroscopic material properties within an object. Tailoring the material constitutive matrix as a function of position results in gradient properties. Once, the target macroscopic properties are known, a mesostructure or a particular material nanostructure can be found which gives the target material properties at each macroscopic point. This research demonstrates that topology and gradient materials can both be optimized together for a single part. The algorithms use a discretized model of the domain and gradient based optimization algorithms. In addition, when considering two conflicting objectives the algorithms in this research generate clear 'features' within a single part. This tailoring of material properties within different areas of a single part (automated design of 'features') using computational design tools is a novel benefit

Evaluation of aluminum drill-pipe material and design

Energy Technology Data Exchange (ETDEWEB)

Placido, Joao C. [PETROBRAS, Rio de Janeiro, RJ (Brazil); Lourenco, Marcelo I.; Netto, Theodoro Antoun [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE)

2008-07-01

Experimental program and numerical analyses were carried out to investigate the fatigue mechanisms of aluminum drill pipes designed and manufactured in compliance with ISO 15546. The main objective is to improve the fatigue performance of these components by selecting the appropriate aluminum alloy and by enhancing the mechanical design of the threaded steel connector. This paper presents the experimental test program and numerical analyses conducted on a drill-pipe of different materials (Al-Cu-Mg and Al-Zn-Mg system aluminum alloys) and geometry. Material mechanical properties, including S-N curve, were determined through small-scale tests on specimens cut from actual drill pipes. Full-scale experiments were also performed in laboratory. A finite element model of the drill pipe, including the tool-joint region, was developed. The model simulates, through different load steps, the tool-joint hot assembly, and then reproduces the physical experiments numerically in order to obtain the actual stress distribution. Good correlation between full-scale and small-scale fatigue tests was obtained by adjusting the strain/stress levels monitored in the full-scale tests in light of the numerical simulations and performing fatigue life calculations via multiaxial fatigue models. The weak points of the current practice design are highlighted for further development. (author)

Design of facilities for processing pyrophoric radioactive material

International Nuclear Information System (INIS)

Bristow, H.A.S.; Hunter, S.D.

1976-01-01

The safe processing of large quantities of plutonium-bearing material poses difficult problems the solution of which sometimes involves conflicting requirements. The difficulties are increased when plutonium of a high burnup is used and the position becomes considerably more complicated when the chemical nature of the material being handled is such that it is pyrophoric. This paper describes the design principles and methods used to establish a facility capable of manufacturing large quantities of mixed plutonium/uranium carbide. The facility which included process stages such as milling, granulation, pellet pressing, furnacing and pin filling, was largely a conversion of an existing processing line. The paper treats the major plant hazards individually and indicates the methods used to counter them, outlining the main design principles employed and describing their application to selected items of equipment. Examples of the problems encountered with typical items of equipment are discussed. Some guide-lines are listed which should be of general value to designers and developers working on equipment for processing plutonium-bearing solids. The methods described have been successfully employed to provide a plant for the manufacture of mixed plutonium/uranium carbide on a scale of many hundreds of kilograms with no serious incident.(author)

Novel material and structural design for large-scale marine protective devices

International Nuclear Information System (INIS)

Qiu, Ang; Lin, Wei; Ma, Yong; Zhao, Chengbi; Tang, Youhong

2015-01-01

Highlights: • Large-scale protective devices with different structural designs have been optimized. • Large-scale protective devices with novel material designs have been optimized. • Protective devices constructed of sandwich panels have the best anti-collision performance. • Protective devices with novel material design can reduce weight and construction cost. - Abstract: Large-scale protective devices must endure the impact of severe forces, large structural deformation, the increased stress and strain rate effects, and multiple coupling effects. In evaluation of the safety of conceptual design through simulation, several key parameters considered in this research are maximum impact force, energy dissipated by the impactor (e.g. a ship) and energy absorbed by the device and the impactor stroke. During impact, the main function of the ring beam structure is to resist and buffer the impact force between ship and bridge pile caps, which could guarantee that the magnitude of impact force meets the corresponding requirements. The means of improving anti-collision performance can be to increase the strength of the beam section or to exchange the steel material with novel fiber reinforced polymer laminates. The main function of the buoyancy tank is to absorb and transfer the ship’s kinetic energy through large plastic deformation, damage, or friction occurring within itself. The energy absorption effect can be improved by structure optimization or by the use of new sandwich panels. Structural and material optimization schemes are proposed on the basis of conceptual design in this research, and protective devices constructed of sandwich panels prove to have the best anti-collision performance

Computational Design of Batteries from Materials to Systems

Energy Technology Data Exchange (ETDEWEB)

Smith, Kandler A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Santhanagopalan, Shriram [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Yang, Chuanbo [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Graf, Peter A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Usseglio Viretta, Francois L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Li, Qibo [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Finegan, Donal [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Pesaran, Ahmad A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Yao, Koffi (Pierre) [Argonne National Laboratory; Abraham, Daniel [Argonne National Laboratory; Dees, Dennis [Argonne National Laboratory; Jansen, Andy [Argonne National Laboratory; Mukherjee, Partha [Texas A& M University; Mistry, Aashutosh [Texas A& M University; Verma, Ankit [Texas A& M University; Lamb, Josh [Sandia National Laboratories; Darcy, Eric [NASA

2017-09-01

Computer models are helping to accelerate the design and validation of next generation batteries and provide valuable insights not possible through experimental testing alone. Validated 3-D physics-based models exist for predicting electrochemical performance, thermal and mechanical response of cells and packs under normal and abuse scenarios. The talk describes present efforts to make the models better suited for engineering design, including improving their computation speed, developing faster processes for model parameter identification including under aging, and predicting the performance of a proposed electrode material recipe a priori using microstructure models.

Computational Chemistry Toolkit for Energetic Materials Design

Science.gov (United States)

2006-11-01

industry are aggressively engaged in efforts to develop multiscale modeling and simulation methodologies to model and analyze complex phenomena across...energetic materials design. It is hoped that this toolkit will evolve into a collection of well-integrated multiscale modeling methodologies...Experimenta Theoreticala This Work 1-5-Diamino-4- methyl- tetrazolium nitrate 8.4 41.7 47.5 1-5-Diamino-4- methyl- tetrazolium azide 138.1 161.6

Perspective: Role of structure prediction in materials discovery and design

Directory of Open Access Journals (Sweden)

Richard J. Needs

2016-05-01

Full Text Available Materials informatics owes much to bioinformatics and the Materials Genome Initiative has been inspired by the Human Genome Project. But there is more to bioinformatics than genomes, and the same is true for materials informatics. Here we describe the rapidly expanding role of searching for structures of materials using first-principles electronic-structure methods. Structure searching has played an important part in unraveling structures of dense hydrogen and in identifying the record-high-temperature superconducting component in hydrogen sulfide at high pressures. We suggest that first-principles structure searching has already demonstrated its ability to determine structures of a wide range of materials and that it will play a central and increasing part in materials discovery and design.

Design rules for phase-change materials in data storage applications

Energy Technology Data Exchange (ETDEWEB)

Lencer, Dominic; Salinga, Martin [I. Physikalisches Institut IA, RWTH Aachen University, 52056 Aachen (Germany); Wuttig, Matthias [I. Physikalisches Institut IA, RWTH Aachen University, 52056 Aachen (Germany); Juelich-Aachen Research Alliance, Section Fundamentals of Future Information Technology (JARA-FIT), 52056 Aachen (Germany)

2011-05-10

Phase-change materials can rapidly and reversibly be switched between an amorphous and a crystalline phase. Since both phases are characterized by very different optical and electrical properties, these materials can be employed for rewritable optical and electrical data storage. Hence, there are considerable efforts to identify suitable materials, and to optimize them with respect to specific applications. Design rules that can explain why the materials identified so far enable phase-change based devices would hence be very beneficial. This article describes materials that have been successfully employed and discusses common features regarding both typical structures and bonding mechanisms. It is shown that typical structural motifs and electronic properties can be found in the crystalline state that are indicative for resonant bonding, from which the employed contrast originates. The occurence of resonance is linked to the composition, thus providing a design rule for phase-change materials. This understanding helps to unravel characteristic properties such as electrical and thermal conductivity which are discussed in the subsequent section. Then, turning to the transition kinetics between the phases, the current understanding and modeling of the processes of amorphization and crystallization are discussed. Finally, present approaches for improved high-capacity optical discs and fast non-volatile electrical memories, that hold the potential to succeed present-day's Flash memory, are presented. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Design rules for phase-change materials in data storage applications.

Science.gov (United States)

Lencer, Dominic; Salinga, Martin; Wuttig, Matthias

2011-05-10

Phase-change materials can rapidly and reversibly be switched between an amorphous and a crystalline phase. Since both phases are characterized by very different optical and electrical properties, these materials can be employed for rewritable optical and electrical data storage. Hence, there are considerable efforts to identify suitable materials, and to optimize them with respect to specific applications. Design rules that can explain why the materials identified so far enable phase-change based devices would hence be very beneficial. This article describes materials that have been successfully employed and dicusses common features regarding both typical structures and bonding mechanisms. It is shown that typical structural motifs and electronic properties can be found in the crystalline state that are indicative for resonant bonding, from which the employed contrast originates. The occurence of resonance is linked to the composition, thus providing a design rule for phase-change materials. This understanding helps to unravel characteristic properties such as electrical and thermal conductivity which are discussed in the subsequent section. Then, turning to the transition kinetics between the phases, the current understanding and modeling of the processes of amorphization and crystallization are discussed. Finally, present approaches for improved high-capacity optical discs and fast non-volatile electrical memories, that hold the potential to succeed present-day's Flash memory, are presented. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Designing Reading Materials for the Faculty of Social and Political Sciences at UIN Syarif Hidayatullah Jakarta

Directory of Open Access Journals (Sweden)

Devi Yusnita

2016-01-01

Full Text Available This research is aimed to design reading materials for the Faculty of Social and Political Sciences, UIN Syarif HIdayatullah Jakarta, due to the absence of such specific materials in the market. To produce satisfactory teaching materials, the researcher did some steps i.e. doing needs analysis, reviewing the principles of materials design and reading strategies, designing course framework, designing syllabus, designing the reading materials, and implementing the sample lessons. The needs analysis was intended to find out what the students needed and to find out the subjects the students learned from the institution in order to produce adequate reading materials. Based on the needs analysis, the researcher then identified the global aims of the course, thereby, the writer designed course framework. This course framework contained general points of reading themes and topics, information of classroom activities that followed up reading, the length of study session, the number of the course meetings, and the number of participants. The course framework became the basis to write the syllabus. Finally the syllabus became the basis for designing reading materials.

Technical Meeting on Liquid Metal Reactor Concepts: Core Design and Structural Materials. Working Material

International Nuclear Information System (INIS)

2013-01-01

The objective of the TM on “Liquid metal reactor concept: core design and structural materials” was to present and discuss innovative liquid metal fast reactor (LMFR) core designs with special focus on the choice, development, testing and qualification of advanced reactor core structural materials. Main results arising from national and international R&D programmes and projects in the field were reviewed, and new activities to be carried out under the IAEA aegis were identified on the basis of the analysis of current research and technology gaps

Steps Towards Industrialization of Cu–III–VI2Thin‐Film Solar Cells:Linking Materials/Device Designs to Process Design For Non‐stoichiometric Photovoltaic Materials

Science.gov (United States)

Chang, Hsueh‐Hsin; Sharma, Poonam; Letha, Arya Jagadhamma; Shao, Lexi; Zhang, Yafei; Tseng, Bae‐Heng

2016-01-01

The concept of in‐line sputtering and selenization become industrial standard for Cu–III–VI2 solar cell fabrication, but still it's very difficult to control and predict the optical and electrical parameters, which are closely related to the chemical composition distribution of the thin film. The present review article addresses onto the material design, device design and process design using parameters closely related to the chemical compositions. Its variation leads to change in the Poisson equation, current equation, and continuity equation governing the device design. To make the device design much realistic and meaningful, we need to build a model that relates the opto‐electrical properties to the chemical composition. The material parameters as well as device structural parameters are loaded into the process simulation to give a complete set of process control parameters. The neutral defect concentrations of non‐stoichiometric CuMSe2 (M = In and Ga) have been calculated under the specific atomic chemical potential conditions using this methodology. The optical and electrical properties have also been investigated for the development of a full‐function analytical solar cell simulator. The future prospects regarding the development of copper–indium–gallium–selenide thin film solar cells have also been discussed. PMID:27840790

Steps Towards Industrialization of Cu-III-VI2Thin-Film Solar Cells:Linking Materials/Device Designs to Process Design For Non-stoichiometric Photovoltaic Materials.

Science.gov (United States)

Hwang, Huey-Liang; Chang, Hsueh-Hsin; Sharma, Poonam; Letha, Arya Jagadhamma; Shao, Lexi; Zhang, Yafei; Tseng, Bae-Heng

2016-10-01

The concept of in-line sputtering and selenization become industrial standard for Cu-III-VI 2 solar cell fabrication, but still it's very difficult to control and predict the optical and electrical parameters, which are closely related to the chemical composition distribution of the thin film. The present review article addresses onto the material design, device design and process design using parameters closely related to the chemical compositions. Its variation leads to change in the Poisson equation, current equation, and continuity equation governing the device design. To make the device design much realistic and meaningful, we need to build a model that relates the opto-electrical properties to the chemical composition. The material parameters as well as device structural parameters are loaded into the process simulation to give a complete set of process control parameters. The neutral defect concentrations of non-stoichiometric CuMSe 2 (M = In and Ga) have been calculated under the specific atomic chemical potential conditions using this methodology. The optical and electrical properties have also been investigated for the development of a full-function analytical solar cell simulator. The future prospects regarding the development of copper-indium-gallium-selenide thin film solar cells have also been discussed.

Regulatory compliance in the design of packages used to transport radioactive materials

International Nuclear Information System (INIS)

Raske, D.T.

1993-01-01

Shipments of radioactive materials within the regulatory jurisdiction of the US Department of Energy (DOE) must meet the package design requirements contained in Title 10 of the Code of Federal Regulations, Part 71, and DOE Order 5480.3. These regulations do not provide design criteria requirements, but only detail the approval standards, structural performance criteria, and package integrity requirements that must be met during transport. The DOE recommended design criterion for high-level Category I radioactive packagings is Section III, Division 1, of the ASME Boiler and Pressure Vessel Code. However, alternative design criteria may be used if all the design requirements are satisfied. The purpose of this paper is to review alternatives to the Code criteria and discuss their applicability to the design of containment vessels in packages for high-level radioactive materials. Issues such as design qualification by physical testing, the use of scale models, and problems encountered using a non-ASME design approach are addressed

Materials Design and System Construction for Conventional and New-Concept Supercapacitors.

Science.gov (United States)

Wu, Zhong; Li, Lin; Yan, Jun-Min; Zhang, Xin-Bo

2017-06-01

With the development of renewable energy and electrified transportation, electrochemical energy storage will be more urgent in the future. Supercapacitors have received extensive attention due to their high power density, fast charge and discharge rates, and long-term cycling stability. During past five years, supercapacitors have been boomed benefited from the development of nanostructured materials synthesis and the promoted innovation of devices construction. In this review, we have summarized the current state-of-the-art development on the fabrication of high-performance supercapacitors. From the electrode material perspective, a variety of materials have been explored for advanced electrode materials with smart material-design strategies such as carbonaceous materials, metal compounds and conducting polymers. Proper nanostructures are engineered to provide sufficient electroactive sites and enhance the kinetics of ion and electron transport. Besides, new-concept supercapacitors have been developed for practical application. Microsupercapacitors and fiber supercapacitors have been explored for portable and compact electronic devices. Subsequently, we have introduced Li-/Na-ion supercapacitors composed of battery-type electrodes and capacitor-type electrode. Integrated energy devices are also explored by incorporating supercapacitors with energy conversion systems for sustainable energy storage. In brief, this review provides a comprehensive summary of recent progress on electrode materials design and burgeoning devices constructions for high-performance supercapacitors.

Evaluation of critical materials in five additional advance design photovoltaic cells

Energy Technology Data Exchange (ETDEWEB)

Smith, S.A.; Watts, R.L.; Martin, P.; Gurwell, W.E.

1981-02-01

The objective of this study is to identify potential material supply constraints due to the large-scale deployment of five advanced photovoltaic (PV) cell designs, and to suggest strategies to reduce the impacts of these production capacity limitations and potential future material shortages. The Critical Materials Assessment Program (CMAP) screens the designs and their supply chains and identifies potential shortages which might preclude large-scale use of the technologies. The results of the screening of five advanced PV cell designs are presented: (1) indium phosphide/cadmium sulfide, (2) zinc phosphide, (3) cadmium telluride/cadmium sulfide, (4) copper indium selenium, and (5) cadmium selenide photoelectrochemical. Each of these five cells is screened individually assuming that they first come online in 1991, and that 25 Gwe of peak capacity is online by the year 2000. A second computer screening assumes that each cell first comes online in 1991 and that each cell has a 5 GWe of peak capacity by the year 2000, so that the total online capacity for the five cells is 25 GWe. Based on a review of the preliminary baseline screening results, suggestions were made for varying such parameters as the layer thickness, cell production processes, etc. The resulting PV cell characterizations were then screened again by the CMAP computer code. The CMAP methodology used to identify critical materials is described; and detailed characterizations of the advanced photovoltaic cell designs under investigation, descriptions of additional cell production processes, and the results are presented. (WHK)

Chalcogenide Glass Radiation Sensor; Materials Development, Design and Device Testing

Energy Technology Data Exchange (ETDEWEB)

Mitkova, Maria; Butt, Darryl; Kozicki, Michael; Barnaby, Hugo

2013-04-30

studied the effect of x-rays and γ-rays, on thin film chalcogenide glasses and applied them in conjunction with film incorporating a silver source in a new type of radiation sensor for which we have an US patent application [3]. In this report, we give data about our studies regarding our designed radiation sensor along with the testing and performance at various radiation doses. These studies have been preceded by materials characterization research related to the compositional and structural characteristics of the active materials used in the radiation sensor design. During the work on the project, we collected a large volume of material since every experiment was repeated many times to verify the results. We conducted a comprehensive material research, analysis and discussion with the aim to understand the nature of the occurring effects, design different structures to harness these effects, generated models to aid in the understanding the effects, built different device structures and collected data to quantify device performance. These various aspects of our investigation have been detailed in previous quarterly reports. In this report, we present our main results and emphasize on the results pertaining to the core project goals materials development, sensor design and testing and with an emphasis on classifying the appropriate material and design for the optimal application. The report has three main parts: (i) Presentation of the main data; (ii) Bulleted summary of the most important results; (iii) List of the patent, journal publications, conference proceedings and conferences participation, occurring as a result of working on the project.

Combinatorial thin film materials science: From alloy discovery and optimization to alloy design

Energy Technology Data Exchange (ETDEWEB)

Gebhardt, Thomas, E-mail: gebhardt@mch.rwth-aachen.de; Music, Denis; Takahashi, Tetsuya; Schneider, Jochen M.

2012-06-30

This paper provides an overview of modern alloy development, from discovery and optimization towards alloy design, based on combinatorial thin film materials science. The combinatorial approach, combining combinatorial materials synthesis of thin film composition-spreads with high-throughput property characterization has proven to be a powerful tool to delineate composition-structure-property relationships, and hence to efficiently identify composition windows with enhanced properties. Furthermore, and most importantly for alloy design, theoretical models and hypotheses can be critically appraised. Examples for alloy discovery, optimization, and alloy design of functional as well as structural materials are presented. Using Fe-Mn based alloys as an example, we show that the combination of modern electronic-structure calculations with the highly efficient combinatorial thin film composition-spread method constitutes an effective tool for knowledge-based alloy design.

Combinatorial thin film materials science: From alloy discovery and optimization to alloy design

International Nuclear Information System (INIS)

Gebhardt, Thomas; Music, Denis; Takahashi, Tetsuya; Schneider, Jochen M.

2012-01-01

This paper provides an overview of modern alloy development, from discovery and optimization towards alloy design, based on combinatorial thin film materials science. The combinatorial approach, combining combinatorial materials synthesis of thin film composition-spreads with high-throughput property characterization has proven to be a powerful tool to delineate composition–structure–property relationships, and hence to efficiently identify composition windows with enhanced properties. Furthermore, and most importantly for alloy design, theoretical models and hypotheses can be critically appraised. Examples for alloy discovery, optimization, and alloy design of functional as well as structural materials are presented. Using Fe-Mn based alloys as an example, we show that the combination of modern electronic-structure calculations with the highly efficient combinatorial thin film composition-spread method constitutes an effective tool for knowledge-based alloy design.

Data-driven design optimization for composite material characterization

Science.gov (United States)

John G. Michopoulos; John C. Hermanson; Athanasios Iliopoulos; Samuel G. Lambrakos; Tomonari Furukawa

2011-06-01

The main goal of the present paper is to demonstrate the value of design optimization beyond its use for structural shape determination in the realm of the constitutive characterization of anisotropic material systems such as polymer matrix composites with or without damage. The approaches discussed are based on the availability of massive experimental data...

Material control system design: Test Bed Nitrate Storage Area (TBNSA)

International Nuclear Information System (INIS)

Clark, G.A.; Da Roza, R.A.; Dunn, D.R.; Sacks, I.J.; Harrison, W.; Huebel, J.G.; Ross, W.N.; Salisbury, J.D.; Sanborn, R.H.; Weissenberger, S.

1978-05-01

This report provides an example of a hypothetical Special Nuclear Material (SNM) Safeguard Material Control and Accounting (MC and A) System which will be used as a subject for the demonstration of the Lawrence Livermore Laboratory MC and A System Evaluation Methodology in January 1978. This methodology is to become a tool in the NRC evaluation of license applicant submittals for Nuclear Fuel Cycle facilities. The starting point for this test bed design was the Allied-General Nuclear Services--Barnwell Nuclear Fuel Plant Reprocessing plant as described in the Final Safety Analysis Report (FSAR), of August 1975. The test bed design effort was limited to providing an SNM safeguard system for the plutonium nitrate storage area of this facility

Designing through Material

DEFF Research Database (Denmark)

Kruse Aagaard, Anders

2014-01-01

as an opportunity to connect the digital environment with the reality of materials – and use realisation and materialisation to generate architectural developments and findings through an iterative mode of thinking about the dialogue between drawing, materials and fabrication. Consequently the interest and mind...

High-performance green semiconductor devices: materials, designs, and fabrication

Science.gov (United States)

Jung, Yei Hwan; Zhang, Huilong; Gong, Shaoqin; Ma, Zhenqiang

2017-06-01

From large industrial computers to non-portable home appliances and finally to light-weight portable gadgets, the rapid evolution of electronics has facilitated our daily pursuits and increased our life comforts. However, these rapid advances have led to a significant decrease in the lifetime of consumer electronics. The serious environmental threat that comes from electronic waste not only involves materials like plastics and heavy metals, but also includes toxic materials like mercury, cadmium, arsenic, and lead, which can leak into the ground and contaminate the water we drink, the food we eat, and the animals that live around us. Furthermore, most electronics are comprised of non-renewable, non-biodegradable, and potentially toxic materials. Difficulties in recycling the increasing amount of electronic waste could eventually lead to permanent environmental pollution. As such, discarded electronics that can naturally degrade over time would reduce recycling challenges and minimize their threat to the environment. This review provides a snapshot of the current developments and challenges of green electronics at the semiconductor device level. It looks at the developments that have been made in an effort to help reduce the accumulation of electronic waste by utilizing unconventional, biodegradable materials as components. While many semiconductors are classified as non-biodegradable, a few biodegradable semiconducting materials exist and are used as electrical components. This review begins with a discussion of biodegradable materials for electronics, followed by designs and processes for the manufacturing of green electronics using different techniques and designs. In the later sections of the review, various examples of biodegradable electrical components, such as sensors, circuits, and batteries, that together can form a functional electronic device, are discussed and new applications using green electronics are reviewed.

Software development for specific geometry and safe design of isotropic material multicell beams

International Nuclear Information System (INIS)

Tariq, M.M.; Ahmed, M.A.

2011-01-01

Comparison of analytical results with finite element results for analysis of isotropic material multicell beams subjected to free torsion case is the main idea of this paper. Progress in the fundamentals and applications of advanced materials and their processing technologies involves costly experiments and prototype testing for reliability. The software development for design analysis of structures with advanced materials is a low cost but challenging research. Multicell beams have important industrial applications in the aerospace and automotive sectors. This paper explains software development to test different materials in design of a multicell beam. Objective of this paper is to compute the torsional loading of multicell beams of isotropic materials for safe design in both symmetrical and asymmetrical geometries. Software has been developed in Microsoft Visual Basic. Distribution of Saint Venant shear flows, shear stresses, factors of safety, volume, mass, weight, twist, polar moment of inertia and aspect ratio for free torsion in multicell beam have been calculated using this software. The software works on four algorithms, these are, Specific geometry algorithm, material selection algorithm, factor of safety algorithm and global algorithm. User can specify new materials analytically, or choose a pre-defined material from the list, which includes, plain carbon steels, low alloy steels, stainless steels, cast irons, aluminum alloys, copper alloys, magnesium alloys, titanium alloys, precious metals and refractory metals. Although this software is restricted to multicell beam comprising of three cells, however future versions can have ability to address more complicated shapes and cases of multicell beams. Software also describes nomenclature and mathematical formulas applied to help user understand the theoretical background. User can specify geometry of multicell beam for three rectangular cells. Software computes shear flows, shear stresses, safety factors

Preliminary Design and Investigation of Integrated Compressor with Composite Material Wheel

Science.gov (United States)

Wang, Jifeng; Müller, Norbert

2012-06-01

An integrated water vapor compressor with composite material wheel is developed and strength analysis using FEM is presented. The design of wound composite material allows for integrating all rotating parts of the drive that may simply reduce to only the rotor of the electrical motor, since no drive shaft is required anymore. This design can reduce the number of parts and mass, which is convenient for engineers to maintain the compressor. The electrical motors are brushless DC motors operating through a frequency drive and apply a torque on the wheels through the materials bonded in the wheel shrouds. This system allows a large amount of compression to be produced in a multi-stage compression setup. To determine the stress and vibration characteristics of this integrated compressor, numerical analysis is carried out using FEM. The simulation result shows that the integrated compressor with composite material wheel can be used in a chiller system where water as a refrigerant.

Design guides for radioactive-material-handling facilities and equipment

International Nuclear Information System (INIS)

Doman, D.R.; Barker, R.E.

1980-01-01

Fourteen key areas relating to facilities and equipment for handling radioactive materials involved in examination, reprocessing, fusion fuel handling and remote maintenance have been defined and writing groups established to prepare design guides for each areas. The guides will give guidance applicable to design, construction, operation, maintenance and safety, together with examples and checklists. Each guide will be reviewed by an independent review group. The guides are expected to be compiled and published as a single document

Material gap membrane distillation: A new design for water vapor flux enhancement

KAUST Repository

Francis, Lijo; Ghaffour, NorEddine; Alsaadi, Ahmad Salem; Amy, Gary L.

2013-01-01

A new module design for membrane distillation, namely material gap membrane distillation (MGMD), for seawater desalination has been proposed and successfully tested. It has been observed that employing appropriate materials between the membrane

High Prevalence of Inadequate Calcium and Iron Intakes by Mexican Population Groups as Assessed by 24-Hour Recalls.

Science.gov (United States)

Sánchez-Pimienta, Tania G; López-Olmedo, Nancy; Rodríguez-Ramírez, Sonia; García-Guerra, Armando; Rivera, Juan A; Carriquiry, Alicia L; Villalpando, Salvador

2016-09-01

A National Health and Nutrition Survey (ENSANUT) conducted in Mexico in 1999 identified a high prevalence of inadequate mineral intakes in the population by using 24-h recall questionnaires. However, the 1999 survey did not adjust for within-person variance. The 2012 ENSANUT implemented a more up-to-date 24-h recall methodology to estimate usual intake distributions and prevalence of inadequate intakes. We examined the distribution of usual intakes and prevalences of inadequate intakes of calcium, iron, magnesium, and zinc in the Mexican population in groups defined according to sex, rural or urban area, geographic region of residence, and socioeconomic status (SES). We used dietary intake data obtained through the 24-h recall automated multiple-pass method for 10,886 subjects as part of ENSANUT 2012. A second measurement on a nonconsecutive day was obtained for 9% of the sample. Distributions of usual intakes of the 4 minerals were obtained by using the Iowa State University method, and the prevalence of inadequacy was estimated by using the Institute of Medicine's Estimated Average Requirement cutoff. Calcium inadequacy was 25.6% in children aged 1-4 y and 54.5-88.1% in subjects >5 y old. More than 45% of subjects >5 y old had an inadequate intake of iron. Less than 5% of children aged 12 y had inadequate intakes of magnesium, whereas zinc inadequacy ranged from <10% in children aged <12 y to 21.6% in men aged ≥20 y. Few differences were found between rural and urban areas, regions, and tertiles of SES. Intakes of calcium, iron, magnesium, and zinc are inadequate in the Mexican population, especially among adolescents and adults. These results suggest a public health concern that must be addressed. © 2016 American Society for Nutrition.

Elementary Students' Learning of Materials Science Practices Through Instruction Based on Engineering Design Tasks

Science.gov (United States)

Wendell, Kristen Bethke; Lee, Hee-Sun

2010-12-01

Materials science, which entails the practices of selecting, testing, and characterizing materials, is an important discipline within the study of matter. This paper examines how third grade students' materials science performance changes over the course of instruction based on an engineering design challenge. We conducted a case study of nine students who participated in engineering design-based science instruction with the goal of constructing a stable, quiet, thermally comfortable model house. The learning outcome of materials science practices was assessed by clinical interviews conducted before and after the instruction, and the learning process was assessed by students' workbooks completed during the instruction. The interviews included two materials selection tasks for designing a sturdy stepstool and an insulated pet habitat. Results indicate that: (1) students significantly improved on both materials selection tasks, (2) their gains were significantly positively associated with the degree of completion of their workbooks, and (3) students who were highly engaged with the workbook's reflective record-keeping tasks showed the greatest improvement on the interviews. These findings suggest the important role workbooks can play in facilitating elementary students' learning of science through authentic activity such as engineering design.

Engineering design skills coverage in K-12 engineering program curriculum materials in the USA

Science.gov (United States)

Chabalengula, Vivien M.; Mumba, Frackson

2017-11-01

The current K-12 Science Education framework and Next Generation Science Standards (NGSS) in the United States emphasise the integration of engineering design in science instruction to promote scientific literacy and engineering design skills among students. As such, many engineering education programmes have developed curriculum materials that are being used in K-12 settings. However, little is known about the nature and extent to which engineering design skills outlined in NGSS are addressed in these K-12 engineering education programme curriculum materials. We analysed nine K-12 engineering education programmes for the nature and extent of engineering design skills coverage. Results show that developing possible solutions and actual designing of prototypes were the highly covered engineering design skills; specification of clear goals, criteria, and constraints received medium coverage; defining and identifying an engineering problem; optimising the design solution; and demonstrating how a prototype works, and making iterations to improve designs were lowly covered. These trends were similar across grade levels and across discipline-specific curriculum materials. These results have implications on engineering design-integrated science teaching and learning in K-12 settings.

Materials Design and System Construction for Conventional and New‐Concept Supercapacitors

Science.gov (United States)

Wu, Zhong; Li, Lin

2017-01-01

With the development of renewable energy and electrified transportation, electrochemical energy storage will be more urgent in the future. Supercapacitors have received extensive attention due to their high power density, fast charge and discharge rates, and long‐term cycling stability. During past five years, supercapacitors have been boomed benefited from the development of nanostructured materials synthesis and the promoted innovation of devices construction. In this review, we have summarized the current state‐of‐the‐art development on the fabrication of high‐performance supercapacitors. From the electrode material perspective, a variety of materials have been explored for advanced electrode materials with smart material‐design strategies such as carbonaceous materials, metal compounds and conducting polymers. Proper nanostructures are engineered to provide sufficient electroactive sites and enhance the kinetics of ion and electron transport. Besides, new‐concept supercapacitors have been developed for practical application. Microsupercapacitors and fiber supercapacitors have been explored for portable and compact electronic devices. Subsequently, we have introduced Li‐/Na‐ion supercapacitors composed of battery‐type electrodes and capacitor‐type electrode. Integrated energy devices are also explored by incorporating supercapacitors with energy conversion systems for sustainable energy storage. In brief, this review provides a comprehensive summary of recent progress on electrode materials design and burgeoning devices constructions for high‐performance supercapacitors. PMID:28638780

Design of materials with extreme thermal expansion using a three-phase topology optimization method

DEFF Research Database (Denmark)

Sigmund, Ole; Torquato, S.

1997-01-01

We show how composites with extremal or unusual thermal expansion coefficients can be designed using a numerical topology optimization method. The composites are composed of two different material phases and void. The optimization method is illustrated by designing materials having maximum therma...

Bulk-shield design for the Fusion Materials Irradiation Test facility

International Nuclear Information System (INIS)

Carter, L.L.; Mann, F.M.; Morford, R.J.; Johnson, D.L.; Huang, S.T.

1982-07-01

The accelerator-based Fusion Materials Irradiation Test (FMIT) facility will provide a high-fluence, fusion-like radiation environment for the testing of materials. While the neutron spectrum produced in the forward direction by the 35 MeV deuterons incident upon a flowing lithium target is characterized by a broad peak around 14 MeV, a high energy tail extends up to about 50 MeV. Some shield design considerations are reviewed

Pipelines cathodic protection design methodologies for impressed ...

African Journals Online (AJOL)

Several inadequate designs of cathodically polarized offshore and onshore pipelines have been reported in Nigeria owing to design complexity and application of the cathodic protection system. The present study focused on critical and detailed approach in impressed current and sacrificial anode design calculation ...

Industrial aspects: materials, designing and quality

International Nuclear Information System (INIS)

Blanc, M.

2008-01-01

First, this article reviews the evolution of the PWR fuel assembly manufactured by Westinghouse over 30 years and secondly gives a glimpse of the industrial organization of Westinghouse. The progressive changes in the design of the fuel assembly can be illustrated by the materials used: first Inconel then zircaloy-4, zirlo and now the optimized zirlo. The Westinghouse nuclear fuel destined to French pressurized reactors is fabricated in either Sweden (Vasteras) or in Spain (Juzbado). Fuel tubes are produced in Usa (Blairsville) or in Sweden (Sandvik). In the last 5 years Westinghouse has launched important programs for improving industrial processes and final products to reach customer satisfaction. (A.C.)

Educative Curriculum Materials: Uptake, Impact, and Implications for Research and Design

Science.gov (United States)

Davis, Elizabeth A.; Palincsar, Annemarie Sullivan; Smith, P. Sean; Arias, Anna Maria; Kademian, Sylvie M.

2017-01-01

The authors synthesize the findings of a research project to extend what is known about educative curriculum materials, or curriculum materials designed with the intent of supporting teacher learning as well as student learning. Drawing on a three-year program of research, including several close observational case studies and a large-scale…

The radioactive materials packaging handbook: Design, operations, and maintenance

International Nuclear Information System (INIS)

Shappert, L.B.; Bowman, S.M.; Arnold, E.D.

1998-01-01

As part of its required activities in 1994, the US Department of Energy (DOE) made over 500,000 shipments. Of these shipments, approximately 4% were hazardous, and of these, slightly over 1% (over 6,400 shipments) were radioactive. Because of DOE's cleanup activities, the total quantities and percentages of radioactive material (RAM) that must be moved from one site to another is expected to increase in the coming years, and these materials are likely to be different than those shipped in the past. Irradiated fuel will certainly be part of the mix as will RAM samples and waste. However, in many cases these materials will be of different shape and size and require a transport packaging having different shielding, thermal, and criticality avoidance characteristics than are currently available. This Handbook provides guidance on the design, testing, certification, and operation of packages for these materials

The radioactive materials packaging handbook: Design, operations, and maintenance

Energy Technology Data Exchange (ETDEWEB)

Shappert, L.B.; Bowman, S.M. [Oak Ridge National Lab., TN (United States); Arnold, E.D. [Lockheed Martin Energy Systems, Oak Ridge, TN (United States)] [and others

1998-08-01

As part of its required activities in 1994, the US Department of Energy (DOE) made over 500,000 shipments. Of these shipments, approximately 4% were hazardous, and of these, slightly over 1% (over 6,400 shipments) were radioactive. Because of DOE`s cleanup activities, the total quantities and percentages of radioactive material (RAM) that must be moved from one site to another is expected to increase in the coming years, and these materials are likely to be different than those shipped in the past. Irradiated fuel will certainly be part of the mix as will RAM samples and waste. However, in many cases these materials will be of different shape and size and require a transport packaging having different shielding, thermal, and criticality avoidance characteristics than are currently available. This Handbook provides guidance on the design, testing, certification, and operation of packages for these materials.

Materials for construction and civil engineering science, processing, and design

CERN Document Server

Margarido, Fernanda

2015-01-01

This expansive volume presents the essential topics related to construction materials composition and their practical application in structures and civil installations. The book's diverse slate of expert authors assemble invaluable case examples and performance data on the most important groups of materials used in construction, highlighting aspects such as nomenclature, the properties, the manufacturing processes, the selection criteria, the products/applications, the life cycle and recyclability, and the normalization. Civil Engineering Materials: Science, Processing, and Design is ideal for practicing architects; civil, construction, and structural engineers, and serves as a comprehensive reference for students of these disciplines. This book also: ·       Provides a substantial and detailed overview of traditional materials used in structures and civil infrastructure ·       Discusses properties of natural and synthetic materials in construction and materials' manufacturing processes ·  �...

Safety by design of printed multilayer materials intended for food packaging.

Science.gov (United States)

Domeño, Celia; Aznar, Margarita; Nerín, Cristina; Isella, Francesca; Fedeli, Mauro; Bosetti, Osvaldo

2017-07-01

Printing inks are commonly used in multilayer plastics materials used for food packaging, and compounds present in inks can migrate to the food either by diffusion through the multilayers or because of set-off phenomena. To avoid this problem, the right design of the packaging is crucial. This paper studies the safety by design of multilayer materials. First, the migration from four different multilayers manufactured using polyethylene terephthalate (PET), aluminium (Al) and polyethylene (PE) was determined. The structural differences among materials such as the presence of inks or lacquer coatings as well as the differences in layers position allowed the study of a safety-by-design approach. Sixty-nine different compounds were detected and identified; 49 of them were not included in the positive list of Regulation EU/10/2011 or in Swiss legislation and 15 belong to Cramer class III, which means that they have a theoretical high toxicity. Some of the compounds related to ink composition were pyrene, a compound commercially used to make dyes and dye precursors and the antioxidant Irganox 1300. The application of external lacquers decreased the concentration of some migrants but also brought the potential for new migrants coming from its composition. A final risk assessment of the material allowed evaluating food safety for different food simulants and confirm it.

System design for safe robotic handling of nuclear materials

International Nuclear Information System (INIS)

Drotning, W.; Wapman, W.; Fahrenholtz, J.; Kimberly, H.; Kuhlmann, J.

1996-01-01

Robotic systems are being developed by the Intelligent Systems and Robotics Center at Sandia National Laboratories to perform automated handling tasks with radioactive nuclear materials. These systems will reduce the occupational radiation exposure to workers by automating operations which are currently performed manually. Because the robotic systems will handle material that is both hazardous and valuable, the safety of the operations is of utmost importance; assurance must be given that personnel will not be harmed and that the materials and environment will be protected. These safety requirements are met by designing safety features into the system using a layered approach. Several levels of mechanical, electrical and software safety prevent unsafe conditions from generating a hazard, and bring the system to a safe state should an unexpected situation arise. The system safety features include the use of industrial robot standards, commercial robot systems, commercial and custom tooling, mechanical safety interlocks, advanced sensor systems, control and configuration checks, and redundant control schemes. The effectiveness of the safety features in satisfying the safety requirements is verified using a Failure Modes and Effects Analysis. This technique can point out areas of weakness in the safety design as well as areas where unnecessary redundancy may reduce the system reliability

Data mining for materials design: A computational study of single molecule magnet

Energy Technology Data Exchange (ETDEWEB)

Dam, Hieu Chi [Japan Advanced Institute of Science and Technology, 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan); Faculty of Physics, Vietnam National University, 334 Nguyen Trai, Hanoi (Viet Nam); Pham, Tien Lam; Ho, Tu Bao [Japan Advanced Institute of Science and Technology, 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan); Nguyen, Anh Tuan [Faculty of Physics, Vietnam National University, 334 Nguyen Trai, Hanoi (Viet Nam); Nguyen, Viet Cuong [HPC Systems, Inc., 3-9-15 Kaigan, Minato-ku, Tokyo 108-0022 (Japan)

2014-01-28

We develop a method that combines data mining and first principles calculation to guide the designing of distorted cubane Mn{sup 4+} Mn {sub 3}{sup 3+} single molecule magnets. The essential idea of the method is a process consisting of sparse regressions and cross-validation for analyzing calculated data of the materials. The method allows us to demonstrate that the exchange coupling between Mn{sup 4+} and Mn{sup 3+} ions can be predicted from the electronegativities of constituent ligands and the structural features of the molecule by a linear regression model with high accuracy. The relations between the structural features and magnetic properties of the materials are quantitatively and consistently evaluated and presented by a graph. We also discuss the properties of the materials and guide the material design basing on the obtained results.

Materials and design concepts for space-resilient structures

Science.gov (United States)

Naser, Mohannad Z.; Chehab, Alaa I.

2018-04-01

Space exploration and terraforming nearby planets have been fascinating concepts for the longest time. Nowadays, that technological advancements with regard to space exploration are thriving, it is only a matter of time before humans can start colonizing nearby moons and planets. This paper presents a state-of-the-art literature review on recent developments of "space-native" construction materials, and highlights evolutionary design concepts for "space-resilient" structures (i.e., colonies and habitats). This paper also details effects of harsh (and unique) space environments on various terrestrial and extraterrestrial construction materials, as well as on space infrastructure and structural systems. The feasibility of exploiting available space resources in terms of "in-situ resource utilization" and "harvesting of elements and compounds", as well as emergence of enabling technologies such as "cultured (lab-grown)" space construction materials are discussed. Towards the end of the present review, number of limitations and challenges facing Lunar and Martian exploration, and venues in-need for urgent research are identified and examined.

New Design Concept for an Excavator Arms by Using Composite Material

Science.gov (United States)

Solazzi, L.; Assi, A.; Ceresoli, F.

2018-06-01

The purpose of the present paper is to lightweight design an excavator arms, by using a different materials and in particular composite material. Specifically, the research is based on the study of a commercial excavator, by determining its geometry and analyzing the load conditions to which it is exposed. These are determined in relation to either the load diagram of the machine or the possible utilities of the excavator, such as the rotation of the machine. The materials used and implemented in the different analytical and numerical elaborations are classic construction steel S 355 (UNI EN 10025-3), high-resistance steel S 890 (UNI EN 10025-6), aluminum Al 6063 T6 (UNI EN 573-3) and the composite material made by carbon fiber and epoxy resin. The adopted constraints for the design of new arms with different materials, non-conventional for these applications, are numerous. The new solutions must present a safety factor either with respect to the yield tensile strength or to the critical load of buckling greater than or equal to the one determined for the excavator in its original geometrical conformation. Another criterion, which has heavily conditioned the geometry of the arms, was given by the fact that the developed solutions must present a very similar value of the maximum displacement in the different load conditions analyzed. A new geometry for arms made by composite material was developed. It was an elliptical conic section, instead of the classic rectangular section, in order to use the filament winding technological process. As for the adoption of the composite material, we focused on the study and the design of this material as long as the interaction with the extremities (made of aluminum) which are interfaced either with the link between the arms or with the elements of the hydraulic plant which serves for the arms movement. From the results developed, it emerges that the solution developed by adopting composite materials is the one that permits the

Inadequate Gestational Weight Gain Predicts Adverse Pregnancy Outcomes in Mothers with Inflammatory Bowel Disease: Results from a Prospective US Pregnancy Cohort.

Science.gov (United States)

Bengtson, May-Bente; Martin, Christopher F; Aamodt, Geir; Vatn, Morten H; Mahadevan, Uma

2017-08-01

Malnutrition and weight loss are common features of patients with inflammatory bowel disease (IBD). To explore the impact of inadequate gestational weight gain (GWG) on adverse outcomes among IBD mothers in the prospective US pregnancy in Inflammatory Bowel Disease and Neonatal Outcomes (PIANO) cohort. The PIANO cohort comprises 559 and 363 pregnant mothers with Crohn's disease (CD) and ulcerative colitis (UC), respectively, enrolled between 2006 and 2014. The mothers were followed during and after pregnancy to ascertain medication, measurement of disease activity and complications during pregnancy and at delivery. Inadequate GWG was based on US Institute of Medicine recommendations. The associations between inadequate GWG and adverse pregnancy outcomes in maternal IBD were analyzed, adjusted for diabetes, hypertension, smoking, maternal age, education, and disease activity. Maternal CD and UC with inadequate GWG had a 2.5-fold increased risk of preterm birth (OR 2.5, CI 1.3, 4.9 and OR 2.5, CI 1.2, 5.6). Furthermore, an increased risk of intrauterine growth restriction and a trend for small for gestational age were demonstrated in CD but not in UC (OR 3.3, CI 1.1, 10.0, OR 4.5, CI 0.8, 24.3, p = 0.08). Flares increased risk of inadequate GWG (OR 1.6, CI 1.2, 2.3, p = 0.002) but did not change the associations between inadequate GWG and adverse pregnancy outcomes in our models. The US PIANO cohort demonstrated that inadequate GWG was a strong independent predictor of adverse pregnancy outcomes in IBD mothers.

Granular Materials and the Risks They Pose for Success on the Moon and Mars

Science.gov (United States)

Wilkinson, R. Allen; Behringer, Robert P.; Jenkins, James T.; Louge, Michel Y.

2005-02-01

Working with soil, sand, powders, ores, cement and sintered bricks, excavating, grading construction sites, driving off-road, transporting granules in chutes and pipes, sifting gravel, separating solids from gases, and using hoppers are so routine that it seems straightforward to do it on the Moon and Mars as we do it on Earth. This paper brings to the fore how little these processes are understood and the millennia-long trial-and-error practices that lead to today's massive over-design, high failure rate, and extensive incremental scaling up of industrial processes because of the inadequate predictive tools for design. We present a number of pragmatic scenarios where granular materials play a role, the risks involved, and what understanding is needed to greatly reduce the risks.

Materials design considerations and selection for a large rad waste incinerator

International Nuclear Information System (INIS)

Vormelker, P.R.; Jenkins, C.F.; Burns, H.H.

1997-01-01

A new incinerator has been built to process self-generated, low level radioactive wastes at the Department of Energy's Savannah River Site. Wastes include protective clothing and other solid materials used during the handling of radioactive materials, and liquid chemical wastes resulting from chemical and waste management operations. The basic design and materials of construction selected to solve the anticipated corrosion problems from hot acidic gases are reviewed. Problems surfacing during trial runs prior to radioactive operations are discussed

International Fusion Materials Irradiation Facility conceptual design activity. Present status and perspective

International Nuclear Information System (INIS)

Kondo, Tatsuo; Noda, Kenji; Oyama, Yukio

1998-01-01

For developing the materials for nuclear fusion reactors, it is indispensable to study on the neutron irradiation behavior under fusion reactor conditions, but there is not any high energy neutron irradiation facility that can simulate fusion reactor conditions at present. Therefore, the investigation of the IFMIF was begun jointly by Japan, USA, Europe and Russia following the initiative of IEA. The conceptual design activities were completed in 1997. As to the background and the course, the present status of the research on heavy irradiation and the testing means for fusion materials, the requirement and the technical basis of high energy neutron irradiation, and the international joint design activities are reported. The materials for fusion reactors are exposed to the neutron irradiation with the energy spectra up to 14 MeV. The requirements from the users that the IFMIF should satisfy, the demand of the tests for the materials of prototype and demonstration fusion reactors and the evaluation of the neutron field characteristics of the IFMIF are discussed. As to the conceptual design of the IFMIF, the whole constitution, the operational mode, accelerator system and target system are described. (K.I.)

Factors associated with inadequate receipt of components and use of antenatal care services in Nigeria: a population-based study.

Science.gov (United States)

Agho, Kingsley E; Ezeh, Osita K; Ogbo, Felix A; Enoma, Anthony I; Raynes-Greenow, Camille

2018-05-01

Antenatal care (ANC) is an essential intervention to improve maternal and child health. In Nigeria, no population-based studies have investigated predictors of poor receipt of components and uptake of ANC at the national level to inform targeted maternal health initiatives. This study aimed to examine factors associated with inadequate receipt of components and use of ANC in Nigeria. The study used information on 20 405 singleton live-born infants of the mothers from the 2013 Nigeria Demographic and Health Survey. Multivariable logistic regression analyses that adjusted for cluster and survey weights were used to determine potential factors associated with inadequate receipt of components and use of ANC. The prevalence of underutilization and inadequate components of ANC were 47.5% (95% CI: 45.2 to 49.9) and 92.6% (95% CI: 91.8 to 93.2), respectively. Common risk factors for underutilization and inadequate components of ANC in Nigeria included residence in rural areas, no maternal education, maternal unemployment, long distance to health facilities and less maternal exposure to the media. Other risk factors for underutilization of ANC were home births and low household wealth. The study suggests that underutilization and inadequate receipt of the components of ANC were associated with amenable factors in Nigeria. Subsidized maternal services and well-guided health educational messages or financial support from the government will help to improve uptake of ANC services.

Process Materialization Using Templates and Rules to Design Flexible Process Models

Science.gov (United States)

Kumar, Akhil; Yao, Wen

The main idea in this paper is to show how flexible processes can be designed by combining generic process templates and business rules. We instantiate a process by applying rules to specific case data, and running a materialization algorithm. The customized process instance is then executed in an existing workflow engine. We present an architecture and also give an algorithm for process materialization. The rules are written in a logic-based language like Prolog. Our focus is on capturing deeper process knowledge and achieving a holistic approach to robust process design that encompasses control flow, resources and data, as well as makes it easier to accommodate changes to business policy.

IFMIF : International Fusion Materials Irradiation Facility Conceptual Design Activity: Final report

International Nuclear Information System (INIS)

Martone, M.

1997-01-01

This report documents the results of the Conceptual Design Activity (CDA) on the International Fusion Materials Irradiation Facility (IFMIF), conducted during 1995 and 1996. The activity is under the auspices of the International Energy Agency (IEA) Implementing Agreement for a Programme of Research and Development on Fusion Materials. An IEA Fusion Materials Executive Subcommittee was charged with overseeing the IFMIF-CDA work. Participants in the CDA are the European Union, Japan, and the United States, with the Russian Federation as an associate member

IFMIF : International Fusion Materials Irradiation Facility Conceptual Design Activity: Final report

Energy Technology Data Exchange (ETDEWEB)

Martone, M [ENEA, Centro Ricerche Frascati, Rome (Italy)

1997-01-01

This report documents the results of the Conceptual Design Activity (CDA) on the International Fusion Materials Irradiation Facility (IFMIF), conducted during 1995 and 1996. The activity is under the auspices of the International Energy Agency (IEA) Implementing Agreement for a Programme of Research and Development on Fusion Materials. An IEA Fusion Materials Executive Subcommittee was charged with overseeing the IFMIF-CDA work. Participants in the CDA are the European Union, Japan, and the United States, with the Russian Federation as an associate member.

Towards intelligent microstructural design of Nanocomposite Materials. Lightweight, high strength structural/armor materials for service in extreme environments

International Nuclear Information System (INIS)

Mara, Nathan Allan; Bronkhorst, Curt Allan; Beyerlein, Irene Jane

2015-01-01

The intent of this research effort is to prove the hypothesis that: Through the employment of controlled processing parameters which are based upon integrated advanced material characterization and multi-physics material modeling, bulk nanolayered composites can be designed to contain high densities of preferred interfaces that can serve as supersinks for the defects responsible for premature damage and failure.

Towards intelligent microstructural design of Nanocomposite Materials. Lightweight, high strength structural/armor materials for service in extreme environments

Energy Technology Data Exchange (ETDEWEB)

Mara, Nathan Allan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Bronkhorst, Curt Allan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Beyerlein, Irene Jane [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-12-21

The intent of this research effort is to prove the hypothesis that: Through the employment of controlled processing parameters which are based upon integrated advanced material characterization and multi-physics material modeling, bulk nanolayered composites can be designed to contain high densities of preferred interfaces that can serve as supersinks for the defects responsible for premature damage and failure.

Tools for Material Design and Selection

Science.gov (United States)

Wehage, Kristopher

The present thesis focuses on applications of numerical methods to create tools for material characterization, design and selection. The tools generated in this work incorporate a variety of programming concepts, from digital image analysis, geometry, optimization, and parallel programming to data-mining, databases and web design. The first portion of the thesis focuses on methods for characterizing clustering in bimodal 5083 Aluminum alloys created by cryomilling and powder metallurgy. The bimodal samples analyzed in the present work contain a mixture of a coarse grain phase, with a grain size on the order of several microns, and an ultra-fine grain phase, with a grain size on the order of 200 nm. The mixing of the two phases is not homogeneous and clustering is observed. To investigate clustering in these bimodal materials, various microstructures were created experimentally by conventional cryomilling, Hot Isostatic Pressing (HIP), Extrusion, Dual-Mode Dynamic Forging (DMDF) and a new 'Gradient' cryomilling process. Two techniques for quantitative clustering analysis are presented, formulated and implemented. The first technique, the Area Disorder function, provides a metric of the quality of coarse grain dispersion in an ultra-fine grain matrix and the second technique, the Two-Point Correlation function, provides a metric of long and short range spatial arrangements of the two phases, as well as an indication of the mean feature size in any direction. The two techniques are implemented on digital images created by Scanning Electron Microscopy (SEM) and Electron Backscatter Detection (EBSD) of the microstructures. To investigate structure--property relationships through modeling and simulation, strategies for generating synthetic microstructures are discussed and a computer program that generates randomized microstructures with desired configurations of clustering described by the Area Disorder Function is formulated and presented. In the computer program, two

Strength behaviour of sintered steel from the view of design-relevant material data

International Nuclear Information System (INIS)

Sonsino, C.M.; Esper, F.J.; Leuze, G.

1982-01-01

A reliable design of sintered components and an aimed material's selection requires the knowledge of designrelevant material data as Cyclic stress-strain-curves, crack propagation and fracture toughness properties as well as statistically evaluated S-N-curves, because conventional material data as tensile strength, monotonic yield strength, elongation, area reduction and impact strength can lead to a false estimation of the material's fatigue behaviour. For this reason the powder metallurgical industry began to determine design-relevant material data on the example of the porous Fe-Cu-C- and Fe-Cu-Ni-alloys. The fatigue tests with notched specimen and different modes of loading show that porous sintered parts having mechanical notches are less sensitive to external notches than wrought steel, because crack-propagation is delayed by pores. The possibility to manufacture cyclic hardening alloys, their relative notch-insensitivity and with wrought steel comparable scatter of fatigue properties show the importance of sintered alloys as alternative materials. (orig.) [de

Inadequate management of pregnancy-associated listeriosis: lessons from four case reports.

Science.gov (United States)

Charlier, C; Goffinet, F; Azria, E; Leclercq, A; Lecuit, M

2014-03-01

Listeria monocytogenes infection during pregnancy can lead to dramatic fetal or neonatal outcomes. No clinical trial has evaluated treatment options, and retrospective studies of cases are therefore important to define optimal regimens. We report four cases of materno-neonatal listeriosis illustrating inadequate antimicrobial therapy management and discuss recommended treatment options. © 2013 The Authors Clinical Microbiology and Infection © 2013 European Society of Clinical Microbiology and Infectious Diseases.

Materials for Consideration in Standardized Canister Design Activities.

Energy Technology Data Exchange (ETDEWEB)

Bryan, Charles R.; Ilgen, Anastasia Gennadyevna; Enos, David George; Teich-McGoldrick, Stephanie; Hardin, Ernest

2014-10-01

This document identifies materials and material mitigation processes that might be used in new designs for standardized canisters for storage, transportation, and disposal of spent nuclear fuel. It also addresses potential corrosion issues with existing dual-purpose canisters (DPCs) that could be addressed in new canister designs. The major potential corrosion risk during storage is stress corrosion cracking of the weld regions on the 304 SS/316 SS canister shell due to deliquescence of chloride salts on the surface. Two approaches are proposed to alleviate this potential risk. First, the existing canister materials (304 and 316 SS) could be used, but the welds mitigated to relieve residual stresses and/or sensitization. Alternatively, more corrosion-resistant steels such as super-austenitic or duplex stainless steels, could be used. Experimental testing is needed to verify that these alternatives would successfully reduce the risk of stress corrosion cracking during fuel storage. For disposal in a geologic repository, the canister will be enclosed in a corrosion-resistant or corrosion-allowance overpack that will provide barrier capability and mechanical strength. The canister shell will no longer have a barrier function and its containment integrity can be ignored. The basket and neutron absorbers within the canister have the important role of limiting the possibility of post-closure criticality. The time period for corrosion is much longer in the post-closure period, and one major unanswered question is whether the basket materials will corrode slowly enough to maintain structural integrity for at least 10,000 years. Whereas there is extensive literature on stainless steels, this evaluation recommends testing of 304 and 316 SS, and more corrosion-resistant steels such as super-austenitic, duplex, and super-duplex stainless steels, at repository-relevant physical and chemical conditions. Both general and localized corrosion testing methods would be used to

Comparison of gap frame designs and materials for precision cathode strip chambers

International Nuclear Information System (INIS)

Horvath, J.A.; Pratuch, S.M.; Belser, F.C.

1993-01-01

Precision cathode strip chamber perimeter designs that incorporate either continuous or discrete-post gap frames are analyzed. The effects of ten design and material combinations on gravity sag, mass, stress, and deflected shape are evaluated. Procedures are recommended for minimizing mass in the chamber perimeter region while retaining structural integrity and electrical design latitude

Research report on design allowable values of structural materials for LMFBR

International Nuclear Information System (INIS)

1978-11-01

The present report is composed of following two main parts. i) review and re-evaluation on test results by FCI Sub-committee studies, performed from 1973 to 1976, ii) review on procedures for determining design allowable values of structural materials for LMFBR components. Re-evaluation works have been made on monotonic tensile properties at elevated temperatures, creep and creep rupture properties, creep-fatigue properties (strain rate and tensile strain hold time effects on strain fatigue properties at elevated temperatures) of Types 316 and 304 stainless steel and 2 1/4Cr-1Mo steel (base and weld metals) produced in Japan. In the first half of the present report, creep-fatigue test results obtained by FCI Sub-committee studies are subjected to re-evaluation by the present P-FCI Sub-committee. Reviews have been made on testing methods on FCI's-creep-fatigue experiments with other test data of the test materials; high temperature monotonic tensile data, creep and creep rupture data, and origin of the test materials. The data of FCI studies are compared with other reference data obtained by several Japanese laboratories. In the latter half of the present report, procedures including ASME's are reviewed for setting design allowable values for LMFBR components on the basis of high temperature strength properties obtained with materials produced in Japan. A creep rupture data of Japanese steels are issued and examined to make proposal for a design allowable stress of S sub(t) through parameter survey. (author)

Biointegrating Materials

Science.gov (United States)

Amédée, J.; Bordenave, L.; Durrieu, M.-C.; Fricain, J.-C.; Pothuaud, L.

The extraordinary increase in human longevity explains the growing need for replacement organs. The remarkable successes of conventional transplants (associated with the development of effective antirejection drugs and improved control of their administration) are also accompanied by certain drawbacks. First on the list is an inadequate supply of replacement organs: the number of candidates for transplants grows larger, opposition to the removal of organs increases, and the number of transplants has reached a ceiling. Furthermore, it has come to light over the past few years that organ transplants carry a significant risk of transmitting pathogens. Finally, the main drawback lies in the need to pursue an immunosuppression treatment. Scientists and doctors have long been in search of alternatives to human organ transplants. According to the definition drawn up in Chester in 1986 at the Consensus Conference organised under the aegis of the European Society for Biomaterials, biomaterials are non-viable materials used in a medical device and destined to interact with biological systems, whether they contribute to the constitution of a diagnostic device, a tissue or organ substitute, or a device designed to provide functional assistance or replacement.

The Creativity Dimension of Instructional Materials Designed by Prospective Teachers: The Comparison across Domains

Directory of Open Access Journals (Sweden)

Ersoy Esen

2017-01-01

Full Text Available This study aims at revealing the creativity dimension of the materials designed and developed by the second year students studying at the department of Computer Education and Instructional Technology. A part of the participants has completed the process by designing materials in their own field, information technologies; while some of them have done so by designing materials in the field of mathematics. The data have been retrieved from an experimental study of 13 weeks. “Teaching Material Creativity Rubric” developed by the researchers, has been used as the data collection tool. The rubric has been developed in order to evaluate the creativity dimensions of products. While developing the rubric, the creative product evaluation dimensions of [14] have been a source of inspiration. The products developed by the students have been evaluated through the retrieved data, in terms of their creativity. The rubric developed includes Originality, Practicality & Sensibility, Productivity & Flexibility, Feasibility, Inclusiveness, and Insightfulness dimensions. In this research, the data of the aforementioned dimensions and sub-dimensions have been evaluated. The results present that the creativity level of the products on teaching information technologies, which have been developed by Computer Education and Instructional Technology (CEIT students, is high. It has been argued that the creativity of domain-specifically developed materials is higher, through literature. Keywords: Material Design in Computers, Mathematics Teaching, Originality, Applicability, Creativity, Creativity and Domainswords.

IFMIF : International Fusion Materials Irradiation Facility Conceptual Design Activity: Executive summary

International Nuclear Information System (INIS)

1997-01-01

This report is a summary of the results of the Conceptual Design Activity (CDA) on the International Fusion Materials Irradiation Facility (IFMIF), conducted during 1995 and 1996. The activity is under the auspices of the International Energy Agency (IEA) Implementing Agreement for a Programme of Research and Development on Fusion Materials. An IEA Fusion Materials Executive Subcommittee was charged with overseeing the IFMIF-CDA work. Participants in the CDA are the European Union, Japan, and the United States, with the Russian Federation as an associate member

IFMIF : International Fusion Materials Irradiation Facility Conceptual Design Activity: Executive summary

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

This report is a summary of the results of the Conceptual Design Activity (CDA) on the International Fusion Materials Irradiation Facility (IFMIF), conducted during 1995 and 1996. The activity is under the auspices of the International Energy Agency (IEA) Implementing Agreement for a Programme of Research and Development on Fusion Materials. An IEA Fusion Materials Executive Subcommittee was charged with overseeing the IFMIF-CDA work. Participants in the CDA are the European Union, Japan, and the United States, with the Russian Federation as an associate member.

Designing ICT Training Material for Chinese Language Arts Teachers.

Science.gov (United States)

Lin, Janet Mei-Chuen; Wu, Cheng-Chih; Chen, Hsiu-Yen

The purpose of this research is to tailor the design of information and communications technology (ICT) training material to the needs of Chinese language arts teachers such that the training they receive will be conducive to effective integration of ICT into instruction. Eighteen experienced teachers participated in a Delphi-like survey that…

Teachers’ Pedagogic Design of Digital Interactive Whiteboard Materials in the UK Secondary School

Directory of Open Access Journals (Sweden)

Carey Jewitt

2008-03-01

Full Text Available Teachers have always made texts for use in the classroom. The wide spread introduction of Interactive whiteboard (IWB technology into UK classrooms, and the screen more generally, makes the multimodal resources of color, image, dynamic movement, and sound newly available for pedagogic design in newly connectable ways. These facilities present teachers with new questions about how to design and use teaching materials, new possibilites and constraints. This presentation will examine teachers' design of digital multimodal resources for IWBs and the influence of prevalent policy discourses of interactivity, multimodality and fast pace influence on teacher’s digital materials for the IWB.

Design, Synthesis and Characterization of Functional Metal-Organic Framework Materials

KAUST Repository

Alamer, Badriah

2015-06-01

Over the past few decades, vast majority of industrial and academic research throughout the world has witnessed the emergence of materials that can serve as ideal candidates for potential utility in desired applications, and these materials are known as Metal Organic Framework (MOFs). This exceptional new family of porous materials is fabricated by linkage of metal ions or clusters and organic linkers via strong bonds. MOFs have been awarded with remarkable interest and widely studied due to their inherent structural methodology (e.g. use of various metals, expanded library of organic building blocks with different geometry and functionality particularly frameworks designed from carboxylate organic linkers) and unquestionably unique structural and chemical features for many practical applications. (i.e. gas storage/separation, catalysis, drug delivery etc). Simply, metal organic frameworks epitomize the beauty of porous chemical structures. From a design perspective, the introduction of the Molecular Building Block (MBB) approach is actively being pursued pathway by researchers toward the construction of MOFs by employing inorganic building blocks and organic linkers and taking advantage of not only their multiple coordination modes and geometries but also the way in which they are reticulated to generate final framework. In this thesis, research studies will be directed toward (i) the investigation of the relationship between experimental parameters and synthesis of well-known fcu –MOF, (ii) rational design and synthesis of new rare earth (RE) based MOFs, (ii) isoreticular materials based on particular MBB ([M3O(RCO2)6]), M= p-and d-block metals, and (iv) zeolite- like metal organic framework assembled from single-metal ion based MBB ([MN2(CO2)4]) via 2-, 3-,and 4-connected organic linkers. Consequently, the porosity, chemical and thermal stability, and gas sorption properties will be evaluated and detailed.

Molecular Understanding and Structural-Based Design of Polyacrylamides and Polyacrylates as Antifouling Materials.

Science.gov (United States)

Chen, Hong; Zhao, Chao; Zhang, Mingzhen; Chen, Qiang; Ma, Jie; Zheng, Jie

2016-04-12

Design and synthesis of highly bioinert and biocompatible antifouling materials are crucial for a broad range of biomedical and engineering applications. Among antifouling materials, polyacrylamides and polyacrylates have proved so promising because of cheap raw materials, ease of synthesis and applicability, and abundant functional groups. The strong surface hydration and the high surface packing density of polyacrylamides and polyacrylates are considered to be the key contributors to their antifouling property. In this article, we review our studies on the design and synthesis of a series of polyacrylamides and polyacrylates with different molecular structures. These polymers can be fabricated into different architectural forms (brushes, nanoparticles, nanogels, and hydrogels), all of which are highly resistant to the attachment of proteins, cells, and bacteria. We find that small structural changes in the polymers can lead to large enhancement in surface hydration and antifouling performance, both showing a positive correlation. This reveals a general design rule for effective antifouling materials. Furthermore, polyacrylamides and polyacrylates are readily functionalized with other bioactive compounds to achieve different new multifunctionalities.

Space Shuttle Orbiter - Leading edge structural design/analysis and material allowables

Science.gov (United States)

Johnson, D. W.; Curry, D. M.; Kelly, R. E.

1986-01-01

Reinforced Carbon-Carbon (RCC), a structural composite whose development was targeted for the high temperature reentry environments of reusable space vehicles, has successfully demonstrated that capability on the Space Shuttle Orbiter. Unique mechanical properties, particularly at elevated temperatures up to 3000 F, make this material ideally suited for the 'hot' regions of multimission space vehicles. Design allowable characterization testing, full-scale development and qualification testing, and structural analysis techniques will be presented herein that briefly chart the history of the RCC material from infancy to eventual multimission certification for the Orbiter. Included are discussions pertaining to the development of the design allowable data base, manipulation of the test data into usable forms, and the analytical verification process.

Readability in reading materials selection and coursebook design for college English in China

OpenAIRE

Lu, Zhongshe

2002-01-01

This thesis studies the application of readability in reading materials selection and coursebook design for college English in an EFL context in China. Its aim is to develop rationales which coursebook writers can utilise in selecting materials as texts and as a basis for designing tasks. This study, through a combination of quantitative and qualitative research methods, argues that readability is applicable in the EFL Chinese context, and readability plays a important role in determining...

Efficient Parameter Searches for Colloidal Materials Design with Digital Alchemy

Science.gov (United States)

Dodd, Paul, M.; Geng, Yina; van Anders, Greg; Glotzer, Sharon C.

Optimal colloidal materials design is challenging, even for high-throughput or genomic approaches, because the design space provided by modern colloid synthesis techniques can easily have dozens of dimensions. In this talk we present the methodology of an inverse approach we term ''digital alchemy'' to perform rapid searches of design-paramenter spaces with up to 188 dimensions that yield thermodynamically optimal colloid parameters for target crystal structures with up to 20 particles in a unit cell. The method relies only on fundamental principles of statistical mechanics and Metropolis Monte Carlo techniques, and yields particle attribute tolerances via analogues of familiar stress-strain relationships.

Recycling issues facing target and RTL materials of inertial fusion designs

International Nuclear Information System (INIS)

El-Guebaly, L.; Wilson, P.; Sawan, M.; Henderson, D.; Varuttamaseni, A.

2005-01-01

Designers of heavy ion (HI) and Z-pinch inertial fusion power plants have explored the potential of recycling the target and recyclable transmission line (RTL) materials as an alternate option to disposal in a geological repository. This work represents the first time a comprehensive recycling assessment was performed on both machines with an exact pulse history. Our results offer two divergent conclusions on the recycling issue. For the HI concept, target recycling is not a 'must' requirement and the preferred option is the one-shot use scenario as target materials represent a small waste stream, less than 1% of the total nuclear island waste. We recommend using low-cost hohlraum materials once-through and then disposing of them instead of recycling expensive materials such as Au and Gd. On the contrary, RTL recycling is a 'must' requirement for the Z-pinch concept in order to minimize the RTL inventory and enhance the economics. The RTLs meet the low level waste and recycling dose requirements with a wide margin when recycled for the entire plant life even without a cooling period. While recycling offers advantages to the Z-pinch system, it adds complexity and cost to the HI designs

OCCUPATIONAL ACCIDENTS AS INDICATORS OF INADEQUATE WORK CONDITIONS AND WORK ENVIRONMENT

OpenAIRE

Petar Babović

2009-01-01

Occupational accidents due to inadequate working conditions and work environment present a major problem in highly industrialised countries, as well as in developing ones. Occupational accidents are a regular and accompanying phenomenon in all human activities and one of the main health related and economic problems in modern societies.The aim of this study is the analysis of the connections of unfavourable working conditions and working environment on occupational accidents. Occurrence of oc...

Examples of density, orientation and shape optimal design for stiffness and/or strength with orthotropic materials

DEFF Research Database (Denmark)

Pedersen, Pauli

2004-01-01

The balance between stiffness and strength design is considered in the present paper. For materials with different levels of orthotropy (including isotropy), we optimize the density distribution as well as the orientational distribution for a short cantilever problem, and discuss the tendencies...... in design and response (energy distributions and stress directions). For a hole in a biaxial stress field, the shape design of the boundary hole is also incorporated. The resulting tapered density distributions may be difficult to manufacture, for example, in micro-mechanics production. For such problems...... a penalization approach to obtain "black and white" designs, i.e. uniform material or holes, is often applied in optimal design. A specific example is studied to show the effect of the penalization, but is restricted here to an isotropic material. When the total amount of material is not specified, a conflict...

First wall and blanket module safety enhancement by material selection and design decision

International Nuclear Information System (INIS)

Merrill, B.J.

1980-01-01

A thermal/mechanical study has been performed which illustrates the behavior of a fusion reactor first wall and blanket module during a loss of coolant flow event. The relative safety advantages of various material and design options were determined. A generalized first wall-blanket concept was developed to provide the flexibility to vary the structural material (stainless steel vs titanium), coolant (helium vs water), and breeder material (liquid lithium vs solid lithium aluminate). In addition, independent vs common first wall-blanket cooling and coupled adjacent module cooling design options were included in the study. The comparative analyses were performed using a modified thermal analysis code to handle phase change problems

High-Pressure Design of Advanced BN-Based Materials

Directory of Open Access Journals (Sweden)

Oleksandr O. Kurakevych

2016-10-01

Full Text Available The aim of the present review is to highlight the state of the art in high-pressure design of new advanced materials based on boron nitride. Recent experimental achievements on the governing phase transformation, nanostructuring and chemical synthesis in the systems containing boron nitride at high pressures and high temperatures are presented. All these developments allowed discovering new materials, e.g., ultrahard nanocrystalline cubic boron nitride (nano-cBN with hardness comparable to diamond, and superhard boron subnitride B13N2. Thermodynamic and kinetic aspects of high-pressure synthesis are described based on the data obtained by in situ and ex situ methods. Mechanical and thermal properties (hardness, thermoelastic equations of state, etc. are discussed. New synthetic perspectives, combining both soft chemistry and extreme pressure–temperature conditions are considered.

Materials for Hydrogen Storage in Nanocavities: Design criteria

Energy Technology Data Exchange (ETDEWEB)

Reguera, E. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada del IPN, Unidad Legaria, Legaria 694, Col. Irrigacion (Mexico)

2009-11-15

The adsorption potential for a given adsorbate depends of both, material surface and adsorbate properties. In this contribution the possible guest-host interactions for H{sub 2} within a cavity or on a surface are discussed considering the molecule physical properties. Five different interactions contribute to the adsorption forces for this molecule: 1) quadrupole moment interaction with the local electric field gradient; 1) electron cloud polarization by a charge center; 3) dispersive forces (van der Waals); 4) quadrupole moment versus quadrupole moment between neighboring H{sub 2} molecules, and, 5) H{sub 2} coordination to a metal center. The relative importance of these five interactions for the hydrogen storage in nanocavities is discussed from experimental evidences in order to extract materials design criteria for molecular hydrogen storage. (author)

PREFACE: International Conference on Advanced Structural and Functional Materials Design 2008

Science.gov (United States)

Kakeshita, Tomoyuki

2009-07-01

The Ministry of Education, Culture, Sports, Science and Technology of Japan started the Priority Assistance for the Formation of Worldwide Renowned Centers of Research - Global COE Program. This program is based on the competitive principle where a third party evaluation decides which program to support and to give priority support to the formation of world-class centers of research. Our program Center of Excellence for Advanced Structural and Functional Materials Design was selected as one of 13 programs in the field of Chemistry and Materials Science. This center is composed of two materials-related Departments in the Graduate School of Engineering: Materials and Manufacturing Science and Adaptive Machine Systems, and 4 Research Institutes: Center for Atomic and Molecular Technologies, Welding and Joining Research Institute, Institute of Scientific and Industrial Research and Research Center for Ultra-High Voltage Electron Microscopy. Recently, materials research, particularly that of metallic materials, has specialized only in individual elemental characteristics and narrow specialty fields, and there is a feeling that the original role of materials research has been forgotten. The 6 educational and research organizations which make up the COE program cooperatively try to develop new advanced structural and functional materials and achieve technological breakthrough for their fabrication processes from electronic, atomic, microstructural and morphological standpoints, focusing on their design and application: development of high performance structural materials such as space plane and turbine blades operating under a severe environment, new fabrication and assembling methods for electronic devices, development of evaluation technique for materials reliability, and development of new biomaterials for regeneration of biological hard tissues. The aim of this international conference was to report the scientific progress in our Global COE program and also to discuss

The ideal usage of sustainable materials and local resources of the interior space design in Jordan

Energy Technology Data Exchange (ETDEWEB)

Fahmi Hussien, Mayyadah [Department of Interior Design, Faculty of Architect and Art, Petra University (Jordan)], Email: Mayada19732004@yahoo.com

2011-07-01

A large amount of waste is generated by buildings over their life cycle, from construction and operation to destruction. Sustainable design principles and recycling programs in buildings can help moderate this waste. The simplest way is directly through the materials used in the building's construction. The materials and resources used should focus on the health and productivity consequences for the building's inhabitants and its environmental, social and economic impacts. This aim of this study is to make certain recommendations with respect to the use of sustainable building materials and resources in indoor spaces in Jordan. A general overview of collection and storage of recyclable materials, waste management, material reuse, and green and rapidly renewable materials is given. Sustainable material usage in the elements of interior design in Jordan is also discussed in two case studies. A set of indicators is proposed which identify the ideal sustainable materials and resources for use in interior design in Jordan to provide a healthy living environment.

Managing inadequate responses to frontline treatment of chronic myeloid leukemia: a case-based review.

Science.gov (United States)

Bixby, Dale L

2013-05-01

The tyrosine kinase inhibitors (TKIs) imatinib, nilotinib, and dasatinib are the standard of care for treating patients with newly diagnosed chronic-phase chronic myeloid leukemia (CML). Compared with interferon-based treatment, the previous standard of care, imatinib is associated with significantly higher cytogenetic response rates and prolonged overall survival. Nilotinib and dasatinib, both newer and more potent TKIs, significantly improve cytogenetic and molecular response rates compared with imatinib. Despite significant advances in CML treatment enabled by the TKIs, a fraction of patients who receive frontline treatment with a TKI demonstrate inadequate response. The reasons for this vary, but in many cases, inadequate response can be attributed to non-adherence to the treatment regimen, intolerance to the drug, intrinsic or acquired resistance to the drug, or a combination of reasons. More often than not, strategies to improve response necessitate a change in treatment plan, either a dose adjustment or a switch to an alternate drug, particularly in the case of drug intolerance or drug resistance. Improved physician-patient communication and patient education are effective strategies to address issues relating to adherence and intolerance. Because inadequate response to TKI treatment correlates with poor long-term outcomes, it is imperative that patients who experience intolerance or who fail to achieve appropriate responses are carefully evaluated so that appropriate treatment modifications can be made to maximize the likelihood of positive long-term outcome. Copyright © 2012. Published by Elsevier Ltd.

Design of materials configurations for enhanced phononic and electronic properties

Science.gov (United States)

Daraio, Chiara

The discovery of novel nonlinear dynamic and electronic phenomena is presented for the specific cases of granular materials and carbon nanotubes. This research was conducted for designing and constructing optimized macro-, micro- and nano-scale structural configurations of materials, and for studying their phononic and electronic behavior. Variation of composite arrangements of granular elements with different elastic properties in a linear chain-of-sphere, Y-junction or 3-D configurations led to a variety of novel phononic phenomena and interesting physical properties, which can be potentially useful for security, communications, mechanical and biomedical engineering applications. Mechanical and electronic properties of carbon nanotubes with different atomic arrangements and microstructures were also investigated. Electronic properties of Y-junction configured carbon nanotubes exhibit an exciting transistor switch behavior which is not seen in linear configuration nanotubes. Strongly nonlinear materials were designed and fabricated using novel and innovative concepts. Due to their unique strongly nonlinear and anisotropic nature, novel wave phenomena have been discovered. Specifically, violations of Snell's law were detected and a new mechanism of wave interaction with interfaces between NTPCs (Nonlinear Tunable Phononic Crystals) was established. Polymer-based systems were tested for the first time, and the tunability of the solitary waves speed was demonstrated. New materials with transformed signal propagation speed in the manageable range of 10-100 m/s and signal amplitude typical for audible speech have been developed. The enhancing of the mitigation of solitary and shock waves in 1-D chains were demonstrated and a new protective medium was designed for practical applications. 1-D, 2-D and 3-D strongly nonlinear system have been investigated providing a broad impact on the whole area of strongly nonlinear wave dynamics and creating experimental basis for new

Materials selection in mechanical design

International Nuclear Information System (INIS)

Ashby, M.F.; Cebon, D.

1993-01-01

A novel materials-selection procedure has been developed and implemented in software. The procedure makes use of Materials Selection Charts: a new way of displaying material property data; and performance indices: combinations of material properties which govern performance. Optimisation methods are employed for simultaneous selection of both material and shape. (orig.)

Materials selection in mechanical design

OpenAIRE

Ashby , M.; Cebon , D.

1993-01-01

A novel materials-selection procedure has been developed and implemented in software. The procedure makes use of Materials Selection Charts: a new way of displaying material property data; and performance indices: combinations of material properties which govern performance. Optimisation methods are employed for simultaneous selection of both material and shape.

Material Control and Accounting Design Considerations for High-Temperature Gas Reactors

International Nuclear Information System (INIS)

Bjornard, Trond; Hockert, John

2011-01-01

The subject of this report is domestic safeguards and security by design (2SBD) for high-temperature gas reactors, focusing on material control and accountability (MC and A). The motivation for the report is to provide 2SBD support to the Next Generation Nuclear Plant (NGNP) project, which was launched by Congress in 2005. This introductory section will provide some background on the NGNP project and an overview of the 2SBD concept. The remaining chapters focus specifically on design aspects of the candidate high-temperature gas reactors (HTGRs) relevant to MC and A, Nuclear Regulatory Commission (NRC) requirements, and proposed MC and A approaches for the two major HTGR reactor types: pebble bed and prismatic. Of the prismatic type, two candidates are under consideration: (1) GA's GT-MHR (Gas Turbine-Modular Helium Reactor), and (2) the Modular High-Temperature Reactor (M-HTR), a derivative of Areva's Antares reactor. The future of the pebble-bed modular reactor (PBMR) for NGNP is uncertain, as the PBMR consortium partners (Westinghouse, PBMR (Pty) and The Shaw Group) were unable to agree on the path forward for NGNP during 2010. However, during the technology assessment of the conceptual design phase (Phase 1) of the NGNP project, AREVA provided design information and technology assessment of their pebble bed fueled plant design called the HTR-Module concept. AREVA does not intend to pursue this design for NGNP, preferring instead a modular reactor based on the prismatic Antares concept. Since MC and A relevant design information is available for both pebble concepts, the pebble-bed HTGRs considered in this report are: (1) Westinghouse PBMR; and (2) AREVA HTR-Module. The DOE Office of Nuclear Energy (DOE-NE) sponsors the Fuel Cycle Research and Development program (FCR and D), which contains an element specifically focused on the domestic (or state) aspects of SBD. This Material Protection, Control and Accountancy Technology (MPACT) program supports the present

Conceptual design report: Nuclear materials storage facility renovation. Part 1, Design concept. Part 2, Project management

International Nuclear Information System (INIS)

1995-01-01

The Nuclear Materials Storage Facility (NMSF) at the Los Alamos National Laboratory (LANL) was a Fiscal Year (FY) 1984 line-item project completed in 1987 that has never been operated because of major design and construction deficiencies. This renovation project, which will correct those deficiencies and allow operation of the facility, is proposed as an FY 97 line item. The mission of the project is to provide centralized intermediate and long-term storage of special nuclear materials (SNM) associated with defined LANL programmatic missions and to establish a centralized SNM shipping and receiving location for Technical Area (TA)-55 at LANL. Based on current projections, existing storage space for SNM at other locations at LANL will be loaded to capacity by approximately 2002. This will adversely affect LANUs ability to meet its mission requirements in the future. The affected missions include LANL's weapons research, development, and testing (WRD ampersand T) program; special materials recovery; stockpile survelliance/evaluation; advanced fuels and heat sources development and production; and safe, secure storage of existing nuclear materials inventories. The problem is further exacerbated by LANL's inability to ship any materials offsite because of the lack of receiver sites for mate rial and regulatory issues. Correction of the current deficiencies and enhancement of the facility will provide centralized storage close to a nuclear materials processing facility. The project will enable long-term, cost-effective storage in a secure environment with reduced radiation exposure to workers, and eliminate potential exposures to the public. This document provides Part I - Design Concept which describes the selected solution, and Part II - Project Management which describes the management system organization, the elements that make up the system, and the control and reporting system

Conceptual design report: Nuclear materials storage facility renovation. Part 1, Design concept. Part 2, Project management

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-14

The Nuclear Materials Storage Facility (NMSF) at the Los Alamos National Laboratory (LANL) was a Fiscal Year (FY) 1984 line-item project completed in 1987 that has never been operated because of major design and construction deficiencies. This renovation project, which will correct those deficiencies and allow operation of the facility, is proposed as an FY 97 line item. The mission of the project is to provide centralized intermediate and long-term storage of special nuclear materials (SNM) associated with defined LANL programmatic missions and to establish a centralized SNM shipping and receiving location for Technical Area (TA)-55 at LANL. Based on current projections, existing storage space for SNM at other locations at LANL will be loaded to capacity by approximately 2002. This will adversely affect LANUs ability to meet its mission requirements in the future. The affected missions include LANL`s weapons research, development, and testing (WRD&T) program; special materials recovery; stockpile survelliance/evaluation; advanced fuels and heat sources development and production; and safe, secure storage of existing nuclear materials inventories. The problem is further exacerbated by LANL`s inability to ship any materials offsite because of the lack of receiver sites for mate rial and regulatory issues. Correction of the current deficiencies and enhancement of the facility will provide centralized storage close to a nuclear materials processing facility. The project will enable long-term, cost-effective storage in a secure environment with reduced radiation exposure to workers, and eliminate potential exposures to the public. This document provides Part I - Design Concept which describes the selected solution, and Part II - Project Management which describes the management system organization, the elements that make up the system, and the control and reporting system.

Parametric analysis and design of a screw extruder for slightly non-Newtonian (pseudoplastic materials

Directory of Open Access Journals (Sweden)

J.I. Orisaleye

2018-04-01

Full Text Available Extruders have found application in the food, polymer and pharmaceutical industries. Rheological characteristics of materials are important in the specification of design parameters of screw extruders. Biopolymers, which consist of proteins, nucleic acids and polysaccharides, are shear-thinning (pseudoplastic within normal operating ranges. However, analytical models to predict and design screw extruders for non-Newtonian pseudoplastic materials are rare. In this study, an analytical model suitable to design a screw extruder for slightly non-Newtonian materials was developed. The model was used to predict the performance of the screw extruder while processing materials with power law indices slightly deviating from unity (the Newtonian case. Using non-dimensional analysis, the effects of design and operational parameters were investigated. Expressions to determine the optimum channel depth and helix angle were also derived. The model is capable of predicting the performance of the screw extruder within the range of power law indices considered (1/2⩽n⩽1. The power law index influences the choice of optimum channel depth and helix angle of the screw extruder. Keywords: Screw extruder, Slightly non-Newtonian, Shear-thinning, Pseudoplastic, Biopolymer, Power law

Inadequate ventilation for nosocomial tuberculosis prevention in public hospitals in Central Thailand.

Science.gov (United States)

Jiamjarasrangsi, W; Bualert, S; Chongthaleong, A; Chaindamporn, A; Udomsantisuk, N; Euasamarnjit, W

2009-04-01

Forty-two community and general hospitals in central Thailand. To examine the adequacy of indoor ventilation for nosocomial tuberculosis (TB) prevention in public hospitals in central Thailand. A cross-sectional survey was conducted among 323 patient care and ancillary areas in the target hospitals. Data on indoor ventilation rate were collected by the tracer gas method and reported as air changes per hour (ACH). The adequacy of the measured ventilation rates were then determined by comparison with the international recommended standard values. Indoor ventilation rates were inadequate in almost half of the studied areas (144/323, 44.6%). The inadequacy was particularly serious in the emergency rooms (ERs) and radiological areas, where 73.8% (31/42 each) of the rooms had ACH below the recommended standards. Detailed analysis showed that most of the rooms with natural ventilation had air exchange rates that exceeded the recommended standards, while the opposite was the case for rooms with air-conditioning, particularly the window or wall-mount type. Indoor ventilation in high-risk nosocomial TB areas in public hospitals in Thailand was inadequate due to the installation of air-conditioning systems in modern buildings.

Household Response to Inadequate Sewerage and Garbage Collection Services in Abuja, Nigeria.

Science.gov (United States)

Abubakar, Ismaila Rimi

2017-01-01

Provision of sanitation and garbage collection services is an important and yet challenging issue in the rapidly growing cities of developing countries, with significant human health and environmental sustainability implications. Although a growing number of studies have investigated the consequences of inadequate delivery of basic urban services in developing countries, few studies have examined how households cope with the problems. Using the Exit, Voice, Loyalty, and Neglect (EVLN) model, this article explores how households respond to inadequate sewerage and garbage collection services in Abuja, Nigeria. Based on a qualitative study, data were gathered from in-depth interviews with sixty households, complemented with personal observation. The findings from grounded analysis indicated that majority (62%) and about half (55%) of the respondents have utilized the informal sector for sewerage services and garbage collection, respectively, to supplement the services provided by the city. While 68% of the respondents reported investing their personal resources to improve the delivery of existing sewerage services, half (53%) have collectively complained to the utility agency and few (22%) have neglected the problems. The paper concludes by discussing the public health and environmental sustainability implications of the findings.

Reuse of low specific activity material as part of LLWR design optimisation

International Nuclear Information System (INIS)

Huntington, Amy; Cummings, Richard; Shevelan, John; Sumerling, Trevor; Baker, Andrew J.

2013-01-01

A final cap will be emplaced over the disposed waste as part of the closure engineering for the UK's Low Level Waste Repository (LLWR). Additional profiling material will be required above the waste to obtain the required land-form. Consideration has been given to the potential opportunity to reuse Low Specific Activity Material (LSAM, defined as up to 200 Bq g -1 ) imported from other sites as a component of the necessary profiling material for the final repository cap. Justification of such a strategy would ultimately require a demonstration that the solution is optimal with respect to other options for the long-term management of such materials. The proposal is currently at the initial evaluation stage and seeks to establish how LSAM reuse within the cap could be achieved within the framework of an optimised safety case for the LLWR, should such a management approach be pursued. The key considerations include the following: The LSAM must provide the same engineering function as the remainder of the profiling material. The cap design must ensure efficient leachate collection, drainage and control for Low Level Waste (LLW) (and, by extension, LSAM) during the Period of Authorisation. In the longer term the engineering design must passively direct any accumulating waters preferentially away from surface water systems. An initial design has been developed that would allow the placement of around 220,000 m 3 of LSAM. The potential impact of the proposal has been assessed against the current Environmental Safety Case. (authors)

Systematic design of 3D auxetic lattice materials with programmable Poisson's ratio for finite strains

Science.gov (United States)

Wang, Fengwen

2018-05-01

This paper presents a systematic approach for designing 3D auxetic lattice materials, which exhibit constant negative Poisson's ratios over large strain intervals. A unit cell model mimicking tensile tests is established and based on the proposed model, the secant Poisson's ratio is defined as the negative ratio between the lateral and the longitudinal engineering strains. The optimization problem for designing a material unit cell with a target Poisson's ratio is formulated to minimize the average lateral engineering stresses under the prescribed deformations. Numerical results demonstrate that 3D auxetic lattice materials with constant Poisson's ratios can be achieved by the proposed optimization formulation and that two sets of material architectures are obtained by imposing different symmetry on the unit cell. Moreover, inspired by the topology-optimized material architecture, a subsequent shape optimization is proposed by parametrizing material architectures using super-ellipsoids. By designing two geometrical parameters, simple optimized material microstructures with different target Poisson's ratios are obtained. By interpolating these two parameters as polynomial functions of Poisson's ratios, material architectures for any Poisson's ratio in the interval of ν ∈ [ - 0.78 , 0.00 ] are explicitly presented. Numerical evaluations show that interpolated auxetic lattice materials exhibit constant Poisson's ratios in the target strain interval of [0.00, 0.20] and that 3D auxetic lattice material architectures with programmable Poisson's ratio are achievable.

Physical and Model Uncertainty for Fatigue Design of Composite Material

DEFF Research Database (Denmark)

Toft, Henrik Stensgaard; Sørensen, John Dalsgaard

The main aim of the present report is to establish stochastic models for the uncertainties related to fatigue design of composite materials. The uncertainties considered are the physical uncertainty related to the static and fatigue strength and the model uncertainty related to Miners rule...

Bioinspired Design of Building Materials for Blast and Ballistic Protection

Directory of Open Access Journals (Sweden)

Yu-Yan Sun

2016-01-01

Full Text Available Nacre in abalone shell exhibits high toughness despite the brittle nature of its major constituent (i.e., aragonite. Its specific structure is a major contributor to the energy absorption capacity of nacre. This paper reviews the mechanisms behind the performance of nacre under shear, uniaxial tension, compression, and bending conditions. The remarkable combination of stiffness and toughness on nacre can motivate the development of bioinspired building materials for impact resistance applications, and the possible toughness designs of cement-based and clay-based composite materials with a layered and staggered structure were discussed.

Harvesting bioenergy with rationally designed complex functional materials

Science.gov (United States)

Kuang, Liangju

A key challenge in renewable energy is to capture, convert and store solar power with earth-abundant materials and environmentally benign technologies. The goal of this thesis is to develop rationally designed complex functional materials for bio-renewable energy applications. On one hand, photoconversion membrane proteins (MPs) are nature's nanoengineering feats for renewable energy management. Harnessing their functions in synthetic systems could help understand, predict, and ultimately control matter and energy at the nanoscale. This is particularly enticing in the post-genome era as recombinant or cell-free expression of many MPs with high yields becomes possible. However, the labile nature of lipid bilayers renders them unsuitable for use in a broad range of engineered systems. A knowledge gap exists about how to design robust synthetic nanomembranes as lipid-bilayer-mimics to support MP functions and how to direct hierarchical MP reconstitution into those membranes to form 2-D or 3-D ordered proteomembrane arrays. Our studies on proteorhodopsin (PR) and bacterial reaction center (BRC), the two light-harvesting MPs, reveal that a charge-interaction-directed reconstitution (CIDR) mechanism induces spontaneous reconstitution of detergent-solubilized MPs into various amphiphilic block copolymer membranes, many of which have far superior stability than lipid bilayers. Our preliminary data also suggest MPs are not enslaved by the biological membranes they derive from; rather, the chemically nonspecific material properties of MP-supporting membranes may act as allosteric regulators. Versatile chemical designs are possible to modulate the conformational energetics of MPs, hence their transport performance in synthetic systems. On the other hand, microalgae are widely regarded as a sustainable feedstock for biofuel production. Microalgae-derived biofuels have not been commercialized yet because current technologies for microalgae dewatering add a huge cost to the

Design and material selection for ITER first wall/blanket, divertor and vacuum vessel

Science.gov (United States)

Ioki, K.; Barabash, V.; Cardella, A.; Elio, F.; Gohar, Y.; Janeschitz, G.; Johnson, G.; Kalinin, G.; Lousteau, D.; Onozuka, M.; Parker, R.; Sannazzaro, G.; Tivey, R.

1998-10-01

Design and R&D have progressed on the ITER vacuum vessel, shielding and breeding blankets, and the divertor. The principal materials have been selected and the fabrication methods selected for most of the components based on design and R&D results. The resulting design changes are discussed for each system.

Design and construction of thermal desorption measurement system for tritium contained materials

International Nuclear Information System (INIS)

Hara, M.; Hatano, Y.; Calderoni, P.; Shimada, M.

2014-01-01

The dual-mode thermal desorption analysis system was designed and built in Idaho National Laboratory (INL) to examine the evolution of the hydrogen isotope gas from materials. The system is equipped with a mass spectrometer for stable hydrogen isotopes and an ionization chamber for tritium components. The performance of the system built was tested with using tritium contained materials. The evolution of tritiated gas species from contaminated materials was measured successfully by using the system. (author)

Connecting drug delivery reality to smart materials design.

Science.gov (United States)

Grainger, David W

2013-09-15

Inflated claims to both design and mechanistic novelty in drug delivery and imaging systems, including most nanotechnologies, are not supported by the generally poor translation of these systems to clinical efficacy. The "form begets function" design paradigm is seductive but perhaps over-simplistic in translation to pharmaceutical efficacy. Most innovations show few clinically important distinctions in their therapeutic benefits in relevant preclinical disease and delivery models, despite frequent claims to the contrary. Long-standing challenges in drug delivery issues must enlist more realistic, back-to-basics approaches to address fundamental materials properties in complex biological systems, preclinical test beds, and analytical methods to more reliably determine fundamental pharmaceutical figures of merit, including drug carrier purity and batch-batch variability, agent biodistribution, therapeutic index (safety), and efficacy. Copyright © 2013 Elsevier B.V. All rights reserved.

[Design of plant leaf bionic camouflage materials based on spectral analysis].

Science.gov (United States)

Yang, Yu-Jie; Liu, Zhi-Ming; Hu, Bi-Ru; Wu, Wen-Jian

2011-06-01

The influence of structure parameters and contents of plant leaves on their reflectance spectra was analyzed using the PROSPECT model. The result showed that the bionic camouflage materials should be provided with coarse surface and spongy inner structure, the refractive index of main content must be close to that of plant leaves, the contents of materials should contain chlorophyll and water, and the content of C-H bond must be strictly controlled. Based on the analysis above, a novel camouflage material, which was constituted by coarse transparent waterproof surface, chlorophyll, water and spongy material, was designed. The result of verifiable experiment showed that the reflectance spectra of camouflage material exhibited the same characteristics as those of plant leaves. The similarity coefficient of reflectance spectrum of the camouflage material and camphor leaves was 0.988 1, and the characteristics of camouflage material did not change after sunlight treatment for three months. The bionic camouflage material, who exhibited a high spectral similarity with plant leaves and a good weather resistance, will be an available method for reconnaissance of hyperspectral imaging hopefully.

Advances in design and modeling of porous materials

Science.gov (United States)

Ayral, André; Calas-Etienne, Sylvie; Coasne, Benoit; Deratani, André; Evstratov, Alexis; Galarneau, Anne; Grande, Daniel; Hureau, Matthieu; Jobic, Hervé; Morlay, Catherine; Parmentier, Julien; Prelot, Bénédicte; Rossignol, Sylvie; Simon-Masseron, Angélique; Thibault-Starzyk, Frédéric

2015-07-01

This special issue of the European Physical Journal Special Topics is dedicated to selected papers from the symposium "High surface area porous and granular materials" organized in the frame of the conference "Matériaux 2014", held on November 24-28, 2014 in Montpellier, France. Porous materials and granular materials gather a wide variety of heterogeneous, isotropic or anisotropic media made of inorganic, organic or hybrid solid skeletons, with open or closed porosity, and pore sizes ranging from the centimeter scale to the sub-nanometer scale. Their technological and industrial applications cover numerous areas from building and civil engineering to microelectronics, including also metallurgy, chemistry, health, waste water and gas effluent treatment. Many emerging processes related to environmental protection and sustainable development also rely on this class of materials. Their functional properties are related to specific transfer mechanisms (matter, heat, radiation, electrical charge), to pore surface chemistry (exchange, adsorption, heterogeneous catalysis) and to retention inside confined volumes (storage, separation, exchange, controlled release). The development of innovative synthesis, shaping, characterization and modeling approaches enables the design of advanced materials with enhanced functional performance. The papers collected in this special issue offer a good overview of the state-of-the-art and science of these complex media. We would like to thank all the speakers and participants for their contribution to the success of the symposium. We also express our gratitude to the organization committee of "Matériaux 2014". We finally thank the reviewers and the staff of the European Physical Journal Special Topics who made the publication of this special issue possible.

Ferroelectric materials for piezoelectric actuators by optimal design

International Nuclear Information System (INIS)

Jayachandran, K.P.; Guedes, J.M.; Rodrigues, H.C.

2011-01-01

Research highlights: → Microstructure optimization of ferroelectric materials by stochastic optimization. → Polycrystalline ferroelectrics possess better piezo actuation than single crystals. → Randomness of the grain orientations would enhance the overall piezoelectricity. - Abstract: Optimization methods provide a systematic means of designing heterogeneous materials with tailored properties and microstructures focussing on a specific objective. An optimization procedure incorporating a continuum modeling is used in this work to identify the ideal orientation distribution of ferroelectrics (FEs) for application in piezoelectric actuators. Piezoelectric actuation is dictated primarily by the piezoelectric strain coefficients d iμ . Crystallographic orientation is inextricably related to the piezoelectric properties of FEs. This suggests that piezoelectric properties can be tailored by a proper choice of the parameters which control the orientation distribution. Nevertheless, this choice is complicated and it is impossible to analyze all possible combinations of the distribution parameters or the angles themselves. Stochastic optimization combined with a generalized Monte Carlo scheme is used to optimize the objective functions, the effective piezoelectric coefficients d 31 and d 15 . The procedure is applied to heterogeneous, polycrystalline, FE ceramics which are essentially an aggregate of variously oriented grains (crystallites). Global piezoelectric properties are calculated using the homogenization method at each grain configuration chosen by the optimization algorithm. Optimal design variables and microstructure that would generate polycrystalline configurations that multiply the macroscopic piezoelectricity are identified.

Pelamis WEC - main body structural design and materials selection

Energy Technology Data Exchange (ETDEWEB)

Anderson, C.

2003-07-01

This report summarises the results of a study evaluating the potential use of rolled steel, glass reinforced plastic, wood-epoxy laminate, and different forms of concrete as primary structural materials for the Pelamis Wave Energy Converter (WEC) as part of a strategy to refine the design by highlighting cost savings for long-term manufacture. Details are given of the drawing up of a load spectrum in order to assess the candidate structures, the choice of glass reinforced plastic, concrete, and steel for further evaluation based on preliminary screening, the assessment of the material requirements for each candidate structure, and cost estimates. The advantages of the use of concrete are discussed and recommendations are presented.

Design and "As Flown" Radiation Environments for Materials in Low Earth Orbit

Science.gov (United States)

Minow, Joseph; McWilliams, Brett; Altstatt, Richard; Koontz, Steven

2006-01-01

A conservative design approach was adopted by the International Space Station Program for specifying total ionizing radiation dose requirements for use in selecting and qualifying materials for construction of the International Space Station. The total ionizing dose design environment included in SSP 30512 Space Station Ionizing Radiation Design Environment is based on trapped proton and electron fluence derived from the solar maximum versions of the AE-8 and AP-8 models, respectively, specified for a circular orbit at 500 km altitude and 51.7 degree inclination. Since launch, the range of altitudes utilized for Space Station operations vary from a minimum of approximately 330 km to a maximum of approximately 405 km with a mean operational altitude less than 400 km. The design environment, therefore, overestimates the radiation environment because the particle flux in the South Atlantic Anomaly is the primary contributor to radiation dose in low Earth orbit and flux within the Anomaly is altitude dependent. In addition, a 2X multiplier is often applied to the design environment to cover effects from the contributions of galactic cosmic rays, solar energetic particle events, geomagnetic storms, and uncertainties in the trapped radiation models which are not explicitly included in the design environment. Application of this environment may give radiation dose overestimates on the order of 1OX to 30X for materials exposed to the space environment, suggesting that materials originally qualified for ten year exposures on orbit may be used for longer periods without replacement. In this paper we evaluate the "as flown" radiation environments derived from historical records of the ISS flight trajectory since launch and compare the results with the SSP 30512 design environment to document the magnitude of the radiation dose overestimate provided by the design environment. "As flown" environments are obtained from application of the AE-8/AP-8 trapped particle models along

Applications of ATILA FEM software to smart materials case studies in designing devices

CERN Document Server

Uchino, Kenji

2013-01-01

ATILA Finite Element Method (FEM) software facilitates the modelling and analysis of applications using piezoelectric, magnetostrictor and shape memory materials. It allows entire designs to be constructed, refined and optimized before production begins. Through a range of instructive case studies, Applications of ATILA FEM software to smart materials provides an indispensable guide to the use of this software in the design of effective products.Part one provides an introduction to ATILA FEM software, beginning with an overview of the software code. New capabilities and loss integratio

Conceptual design of reinforced concrete structures using topology optimization with elastoplastic material modeling

DEFF Research Database (Denmark)

Bogomolny, Michael; Amir, Oded

2012-01-01

Design of reinforced concrete structures is governed by the nonlinear behavior of concrete and by its different strengths in tension and compression. The purpose of this article is to present a computational procedure for optimal conceptual design of reinforced concrete structures on the basis...... response must be considered. Optimized distribution of materials is achieved by introducing interpolation rules for both elastic and plastic material properties. Several numerical examples illustrate the capability and potential of the proposed procedure. Copyright © 2012 John Wiley & Sons, Ltd....

Road Materials and Pavement Design Volume 17(1)

CSIR Research Space (South Africa)

De Beer, Morris

2016-03-01

Full Text Available Materials and Pavement Design Volume 17, 2016 - Issue 1 Editorial Board Page ebi | Published online: 03 Oct 2016  http://dx.doi.org/10.1080/14680629.2016.1244475 Editors-in-Chief Hervé DI BENEDETTO - University of Lyon/ENTPE, Vaulx-en-Velin, France... Andrew Charles COLLOP - De Montfort University, Leicester, UK William G. BUTTLAR - University of Missouri, Urbana-Champaign, USA Editor-in-Chief at Large Jorge B. Sousa - Consulpav, Oeiras, Portugal Associate Editors Morris de Beer - CSIR Built...

Design and synthesis of polyoxometalate-framework materials from cluster precursors

Science.gov (United States)

Vilà-Nadal, Laia; Cronin, Leroy

2017-10-01

Inorganic oxide materials are used in semiconductor electronics, ion exchange, catalysis, coatings, gas sensors and as separation materials. Although their synthesis is well understood, the scope for new materials is reduced because of the stability limits imposed by high-temperature processing and top-down synthetic approaches. In this Review, we describe the derivatization of polyoxometalate (POM) clusters, which enables their assembly into a range of frameworks by use of organic or inorganic linkers. Additionally, bottom-up synthetic approaches can be used to make metal oxide framework materials, and the features of the molecular POM precursors are retained in these structures. Highly robust all-inorganic frameworks can be made using metal-ion linkers, which combine molecular synthetic control without the need for organic components. The resulting frameworks have high stability, and high catalytic, photochemical and electrochemical activity. Conceptually, these inorganic oxide materials bridge the gap between zeolites and metal-organic frameworks (MOFs) and establish a new class of all-inorganic POM frameworks that can be designed using topological and reactivity principles similar to MOFs.

Site layout and balance of plant design for an accelerator-driven materials processing complex

Energy Technology Data Exchange (ETDEWEB)

Cunliffe, J.; Taussig, R.; Ghose, S. [Bechtel Corporation, San Francisco, CA (United States)] [and others

1995-10-01

High energy proton beam accelerators are under consideration for use in radioisotope production, surplus weapons material destruction, radioactive waste transmutation, and thorium-based energy conversion cycles. While there are unique aspects to each of these applications that must be accommodated in the design of the associated facility, all share a set of fundamental characteristics that in large measure dictate the site layout features and many balance-of-plant (BOP) design requirements found to be common to all. This paper defines these key design determinants and goes on to discuss the manner in which they have been accommodated in the pre-conceptual design for a particular materials production application. An estimate of the costs associated with this BOP design is also presented with the aim of guiding future evaluations where the basic plant designs are similar to that of this specific case.

Designing Next Generation Rechargeable Battery Materials from First-Principles

Science.gov (United States)

Kim, Soo

Technology has advanced rapidly, especially in the twenty-first century, influencing our day-to-day life on unprecedented levels. Most such advances in technology are closely linked to, and often driven by, the discovery and design of new materials. It follows that the discovery of new materials can not only improve existing technologies but also lead to revolutionary ones. In particular, there is a growing need to develop new energy materials that are reliable, clean, and affordable for emerging applications such as portable electronics, electric vehicles, and power grid systems. Many researchers have been actively searching for more cost-effective and clean electrode materials for lithium-ion batteries (LIBs) during the last few decades. These new electrode materials are also required to achieve higher electrochemical performance, compared to the already commercialized electrodes. Unfortunately, discovering the next sustainable energy materials based on a traditional 'trial-and-error' method via experiment would be extremely slow and difficult. In the last two decades, computational compilations of battery material properties such as voltage, diffusivity, and phase stability against irreversible phase transformation(s) using first-principles density functional theory (DFT) calculations have helped researchers to understand the underlying mechanism in many oxide materials that are used as LIB electrodes. Here, we have examined the (001) and (111) surface structures of LiMn2O4 (LMO) spinel cathode materials using DFT calculations within the generalized gradient approximation (GGA) + U approach. Our theoretical results explain the observation of a wide spectrum of polyhedral shapes between (001)- and (111)-dominated LMO particles in experiments, which can be described by the narrow range of surface energies and their sensitivity to synthesis conditions. We further show that single-layer graphene coatings help suppress manganese dissolution in LMO by chemically

Ultra High-Performance Fiber-Reinforced Concrete (UHPFRC: a review of material properties and design procedures

Directory of Open Access Journals (Sweden)

T. E. T. Buttignol

Full Text Available ABSTRACT This paper does a review of the recent achievements on the knowledge of UHPFRC properties and in the development of design procedures. UHPFRC is defined as a new material, with unique properties (high ductility, low permeability, very high strength capacity in compression, higher toughness in comparison to conventional concrete. It is important to know both material and mechanical properties to fully take advantage of its outstanding properties for structural applications. However, since this is a new material, the current design codes are not well suited and should be reviewed before being applied to UHPFRC. In the first part, the following material properties are addressed: hydration process; permeability; fibers role; mix design; fiber-matrix bond properties workability; mixing procedure; and curing. In the second part, the mechanical properties of the material are discussed, together with some design recommendations. The aspects herein examined are: size effect; compressive and flexural strength; tensile stress-strain relation; shear and punching shear capacity; creep and shrinkage; fracture energy; steel bars anchorage and adherence. Besides, the tensile mechanical characterization is described using inverse analysis based on bending tests data. In the last part, material behavior at high temperature is discussed, including physical-chemical transformations of the concrete, spalling effect, and transient creep. In the latter case, a new Load Induced Thermal Strain (LITS semi-empirical model is described and compared with UHPC experimental results.

Design and material selection for ITER first wall/blanket, divertor and vacuum vessel

Energy Technology Data Exchange (ETDEWEB)

Ioki, K.; Barabash, V.; Cardella, A.; Elio, F.; Gohar, Y.; Janeschitz, G.; Johnson, G.; Kalinin, G.; Lousteau, D.; Onozuka, M.; Parker, R.; Sannazzaro, G.; Tivey, R. [ITER JCT, Garching (Germany)

1998-10-01

Design and R and D have progressed on the ITER vacuum vessel, shielding and breeding blankets, and the divertor. The principal materials have been selected and the fabrication methods selected for most of the components based on design and R and D results. The resulting design changes are discussed for each system. (orig.) 11 refs.

Geotechnical materials considerations for conceptual repository design in the Palo Duro Basin, Texas

International Nuclear Information System (INIS)

Versluis, W.S.; Balderman, M.A.

1984-01-01

The Palo Duro Basin is only one of numerous potential repository locations for placement of a nuclear waste repository. Conceptual designs in the Palo Duro Basin involve considerations of the character and properties of the geologic materials found on several sites throughout the Basin. The first consideration presented includes current basin exploration results and interpretations of engineering properties for the basin geologic sequences. The next consideration presented includes identification of the characteristics of rock taken from the geologic sequence of interest through laboratory and field testing. Values for materials properties of representative samples are obtained for input into modeling of the material response to repository placement. Conceptual designs which respond to these geotechnical considerations are discussed. 4 references, 4 figures, 4 tables

Exascale Co-design for Modeling Materials in Extreme Environments

Energy Technology Data Exchange (ETDEWEB)

Germann, Timothy C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-07-08

Computational materials science has provided great insight into the response of materials under extreme conditions that are difficult to probe experimentally. For example, shock-induced plasticity and phase transformation processes in single-crystal and nanocrystalline metals have been widely studied via large-scale molecular dynamics simulations, and many of these predictions are beginning to be tested at advanced 4th generation light sources such as the Advanced Photon Source (APS) and Linac Coherent Light Source (LCLS). I will describe our simulation predictions and their recent verification at LCLS, outstanding challenges in modeling the response of materials to extreme mechanical and radiation environments, and our efforts to tackle these as part of the multi-institutional, multi-disciplinary Exascale Co-design Center for Materials in Extreme Environments (ExMatEx). ExMatEx has initiated an early and deep collaboration between domain (computational materials) scientists, applied mathematicians, computer scientists, and hardware architects, in order to establish the relationships between algorithms, software stacks, and architectures needed to enable exascale-ready materials science application codes within the next decade. We anticipate that we will be able to exploit hierarchical, heterogeneous architectures to achieve more realistic large-scale simulations with adaptive physics refinement, and are using tractable application scale-bridging proxy application testbeds to assess new approaches and requirements. Such current scale-bridging strategies accumulate (or recompute) a distributed response database from fine-scale calculations, in a top-down rather than bottom-up multiscale approach.

76 FR 33780 - Assessments for Mismatched Payments or Inadequate Payment Information for Geothermal, Solid...

Science.gov (United States)

2011-06-09

...] Assessments for Mismatched Payments or Inadequate Payment Information for Geothermal, Solid Minerals, and...: Regulations for geothermal, solid minerals, and Indian oil and gas leases authorize the Office of Natural..., Office of Natural Resources Revenue, P.O. Box 25165, MS 61211B, Denver, Colorado 80225-0165...

Performance of the lot quality assurance sampling method compared to surveillance for identifying inadequately-performing areas in Matlab, Bangladesh.

Science.gov (United States)

Bhuiya, Abbas; Hanifi, S M A; Roy, Nikhil; Streatfield, P Kim

2007-03-01

This paper compared the performance of the lot quality assurance sampling (LQAS) method in identifying inadequately-performing health work-areas with that of using health and demographic surveillance system (HDSS) data and examined the feasibility of applying the method by field-level programme supervisors. The study was carried out in Matlab, the field site of ICDDR,B, where a HDSS has been in place for over 30 years. The LQAS method was applied in 57 work-areas of community health workers in ICDDR,B-served areas in Matlab during July-September 2002. The performance of the LQAS method in identifying work-areas with adequate and inadequate coverage of various health services was compared with those of the HDSS. The health service-coverage indicators included coverage of DPT, measles, BCG vaccination, and contraceptive use. It was observed that the difference in the proportion of work-areas identified to be inadequately performing using the LQAS method with less than 30 respondents, and the HDSS was not statistically significant. The consistency between the LQAS method and the HDSS in identifying work-areas was greater for adequately-performing areas than inadequately-performing areas. It was also observed that the field managers could be trained to apply the LQAS method in monitoring their performance in reaching the target population.

Cognitive Dissonance, Confirmatory Bias and Inadequate Information Processing: Evidence from Experimental Auctions

OpenAIRE

Cao, Ying; Just, David R.; Wansink, Brian

2014-01-01

Using psychological terms such as cognitive dissonance and confirmation bias, this study reveals how individual consumers inadequately process (food safety) information, pay limited attention to signals, and make purchase decisions that are bias towards their initial choices. While it is expected that reading extra information about potential risk associated with the food decreases consumers' willingness to pay (WTP), the magnitude of the impact varies across individuals. In general, consumer...

From molecular design and materials construction to organic nanophotonic devices.

Science.gov (United States)

Zhang, Chuang; Yan, Yongli; Zhao, Yong Sheng; Yao, Jiannian

2014-12-16

CONSPECTUS: Nanophotonics has recently received broad research interest, since it may provide an alternative opportunity to overcome the fundamental limitations in electronic circuits. Diverse optical materials down to the wavelength scale are required to develop nanophotonic devices, including functional components for light emission, transmission, and detection. During the past decade, the chemists have made their own contributions to this interdisciplinary field, especially from the controlled fabrication of nanophotonic molecules and materials. In this context, organic micro- or nanocrystals have been developed as a very promising kind of building block in the construction of novel units for integrated nanophotonics, mainly due to the great versatility in organic molecular structures and their flexibility for the subsequent processing. Following the pioneering works on organic nanolasers and optical waveguides, the organic nanophotonic materials and devices have attracted increasing interest and developed rapidly during the past few years. In this Account, we review our research on the photonic performance of molecular micro- or nanostructures and the latest breakthroughs toward organic nanophotonic devices. Overall, the versatile features of organic materials are highlighted, because they brings tunable optical properties based on molecular design, size-dependent light confinement in low-dimensional structures, and various device geometries for nanophotonic integration. The molecular diversity enables abundant optical transitions in conjugated π-electron systems, and thus brings specific photonic functions into molecular aggregates. The morphology of these micro- or nanostructures can be further controlled based on the weak intermolecular interactions during molecular assembly process, making the aggregates show photon confinement or light guiding properties as nanophotonic materials. By adoption of some active processes in the composite of two or more

Materials and design experience in a slurry-fed electric glass melter

International Nuclear Information System (INIS)

Barnes, S.M.; Larson, D.E.

1981-08-01

The design of a slurry-fed electric gas melter and an examination of the performance and condition of the construction materials were completed. The joule-heated, ceramic-lined melter was constructed to test the applicability of materials and processes for high-level waste vitrification. The developmental Liquid-Fed Ceramic Melter (LFCM) was operated for three years with simulated high-level waste and was subjected to conditions more severe than those expected for a nuclear waste vitrification plant

Design of a deposit of waste materials coming from mining exploitations

International Nuclear Information System (INIS)

Castro, Alvaro; Pinzon, Hernan; Vargas, William; Pinzon, Andres

2005-01-01

This paper presents the design process and stability assessment of a waste backfill in a limestone quarry method. The study shows the geotechnical and mining features of waste and underground materials affected by backfill. The mainly waste materials are: clay, gravel, and blocks of clay stone, sandstone and limestone, all to be disposed by a layered embankment. The constructive method is selected and the stability analysis of deposit and soil foundation was made by equilibrium method without considering deformations

Uncertainty analysis in raw material and utility cost of biorefinery synthesis and design

DEFF Research Database (Denmark)

Cheali, Peam; Quaglia, Alberto; Gernaey, Krist

2014-01-01

are characterized by considerable uncertainty. These uncertainties might have significant impact on the results of the design problem, and therefore need to be carefully evaluated and managed, in order to generate candidates for robust design. In this contribution, we study the effect of data uncertainty (raw...... material price and utility cost) on the design of a biorefinery process network....

Information Technology and Transcription of Reading Materials for the Visually Impaired Persons in Nigeria

Science.gov (United States)

Nkiko, Christopher; Atinmo, Morayo I.; Michael-Onuoha, Happiness Chijioke; Ilogho, Julie E.; Fagbohun, Michael O.; Ifeakachuku, Osinulu; Adetomiwa, Basiru; Usman, Kazeem Omeiza

2018-01-01

Studies have shown inadequate reading materials for the visually impaired in Nigeria. Information technology has greatly advanced the provision of information to the visually impaired in other industrialized climes. This study investigated the extent of application of information technology to the transcription of reading materials for the…

Synergistic Integration of Experimental and Simulation Approaches for the de Novo Design of Silk-Based Materials.

Science.gov (United States)

Huang, Wenwen; Ebrahimi, Davoud; Dinjaski, Nina; Tarakanova, Anna; Buehler, Markus J; Wong, Joyce Y; Kaplan, David L

2017-04-18

Tailored biomaterials with tunable functional properties are crucial for a variety of task-specific applications ranging from healthcare to sustainable, novel bio-nanodevices. To generate polymeric materials with predictive functional outcomes, exploiting designs from nature while morphing them toward non-natural systems offers an important strategy. Silks are Nature's building blocks and are produced by arthropods for a variety of uses that are essential for their survival. Due to the genetic control of encoded protein sequence, mechanical properties, biocompatibility, and biodegradability, silk proteins have been selected as prototype models to emulate for the tunable designs of biomaterial systems. The bottom up strategy of material design opens important opportunities to create predictive functional outcomes, following the exquisite polymeric templates inspired by silks. Recombinant DNA technology provides a systematic approach to recapitulate, vary, and evaluate the core structure peptide motifs in silks and then biosynthesize silk-based polymers by design. Post-biosynthesis processing allows for another dimension of material design by controlled or assisted assembly. Multiscale modeling, from the theoretical prospective, provides strategies to explore interactions at different length scales, leading to selective material properties. Synergy among experimental and modeling approaches can provide new and more rapid insights into the most appropriate structure-function relationships to pursue while also furthering our understanding in terms of the range of silk-based systems that can be generated. This approach utilizes nature as a blueprint for initial polymer designs with useful functions (e.g., silk fibers) but also employs modeling-guided experiments to expand the initial polymer designs into new domains of functional materials that do not exist in nature. The overall path to these new functional outcomes is greatly accelerated via the integration of

Elementary Students' Learning of Materials Science Practices through Instruction Based on Engineering Design Tasks

Science.gov (United States)

Wendell, Kristen Bethke; Lee, Hee-Sun

2010-01-01

Materials science, which entails the practices of selecting, testing, and characterizing materials, is an important discipline within the study of matter. This paper examines how third grade students' materials science performance changes over the course of instruction based on an engineering design challenge. We conducted a case study of nine…

New approach to design of ceramic/polymer material compounds

International Nuclear Information System (INIS)

Todt, A; Nestler, D; Trautmann, M; Wagner, G

2016-01-01

The damage tolerance of carbon fibre-reinforced ceramic-matrix composite materials depends on their porosity and can be rather significant. Complex structures are difficult to produce. The integration of simple geometric structures of ceramic-matrix composite materials in complex polymer-based hybrid structures is a possible approach of realising those structures. These hybrid material compounds, produced in a cost-efficient way, combine the different advantages of the individual components in one hybrid material compound. In addition the individual parts can be designed to fit a specific application and the resulting forces. All these different advantages result in a significant reduction of not only the production costs and the production time, but also opens up new areas of application, such as the large-scale production of wear-resistant and chemically inert, energy dampening components for reactors or in areas of medicine. The low wettability of the ceramic component however is a disadvantage of this approach. During the course of this contribution, different C/C composite materials with a specific porosity were produced, while adjusting the resin/hardening agent-ratio, as well as the processing parameters. After the production, different penetration tests were conducted with a polymer component. The final part of the article is comprised of the microstructural analysis and the explanation of the mechanical relationships. (paper)

Advances in regulation and package design for transportation or storage of radioactive materials 1991

International Nuclear Information System (INIS)

Carlson, R.W.; Fischer, L.E.; Chou, C.K.

1991-01-01

The design of packages for the transport or storage of radioactive materials, particularly spent nuclear fuel, has been evolving in three major areas. The most significant changes have been increases n the capacity of packages. Testing has received increasing importance to supplement analysis and to verify the accuracy of the computer models to represent the more complex designs. New materials have also been proposed that are capable of serving more than one function within a package which would reduce weight and offer the possibility of simplifying package design. It is the intent of the papers presented in this volume to address the impact of these developments by presenting papers that describe testing methods, materials development programs and recent package designs. Decommissioning of nuclear facilities is a field that is beginning to emerge as a major field of endeavor that spans the mechanical engineering, nuclear engineering and many other disciplines. Papers included in this publication describe efforts to understand the mechanics of decontamination of surfaces that have been exposed to radioactive materials and the application of robotics to perform tasks that would be excessively hazardous for humans. Presentation of these papers within the format of the ASME has been chosen to focus attention upon the importance of designing packages in accordance with the Boiler and Pressure Vessel Coal. The papers contained herein have been subjected to a formal review process in accordance with ASME requirements

Impact of schoolchildren's involvement in the design process on the effectiveness of healthy food promotion materials.

Science.gov (United States)

Gustafson, Christopher R; Abbey, Bryce M; Heelan, Kate A

2017-06-01

Marketing techniques may improve children's vegetable consumption. However, student participation in the design of marketing materials may increase the material's salience, while also improving children's commitment and attitudes towards healthy eating. The impact of student-led design of vegetable promotional materials on choice and consumption was investigated using 1614 observations of students' vegetable choice and plate waste in four public elementary schools in Kearney, Nebraska. Data were collected on children's vegetable choice and consumption in four comparison groups: 1) control; 2) students designed materials only; 3) students were exposed to promotional materials only; and 4) students designed materials that were then posted in the lunchroom. Vegetable choice and consumption data were collected through a validated digital photography-based plate-waste method. Multivariate linear regression was used to estimate average treatment effects of the conditions at various time periods. Dependent variables were vegetable choice and consumption, and independent variables included the condition, time period, and interaction terms, as well as controls for gender and grade. Relative to baseline, students in group 4 doubled their vegetable consumption ( p  < 0.001) when materials were posted. Vegetable consumption remained elevated at a follow-up 2-3 months later ( p  < 0.05). Students in group 3 initially increased the quantity of vegetables selected ( p  < 0.05), but did not increase consumption. In the follow-up period, however, students in group 3 increased their vegetable consumption ( p  < 0.01). Involving elementary-aged students in the design of vegetable promotional materials that were posted in the lunchroom increased the amount of vegetables students consumed.

Designing Biomimetic, Dissipative Material Systems

Energy Technology Data Exchange (ETDEWEB)

Balazs, Anna C. [Univ. of Pittsburgh, PA (United States). Chemical Engineering Dept.; Whitesides, George M. [Harvard Univ., Cambridge, MA (United States). Dept. of Chemistry and Chemical Biology; Brinker, C. Jeffrey [Univ. of New Mexico, Albuquerque, NM (United States). Dept. of Chemical and Nuclear Engineering. Dept. of Chemistry. Dept. of Molecular Genetics and Microbiology. Center for Micro-Engineered Materials; Aranson, Igor S. [UChicago, LLC., Argonne, IL (United States); Chaikin, Paul [New York Univ. (NYU), NY (United States). Dept. of Physics; Dogic, Zvonimir [Brandeis Univ., Waltham, MA (United States). Dept. of Physics; Glotzer, Sharon [Univ. of Michigan, Ann Arbor, MI (United States). Dept. of Chemical Engineering. Dept. of Materials Science and Engineering. Dept. of Macromolecular Science and Engineering Physics; Hammer, Daniel [Univ. of Pennsylvania, Philadelphia, PA (United States). School of Engineering and Applied Science; Irvine, Darrell [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States). Dept. of Materials Science and Engineering and Biological Engineering; Little, Steven R. [Univ. of Pittsburgh, PA (United States). Chemical Engineering Dept.; Olvera de la Cruz, Monica [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering; Parikh, Atul N. [Univ. of California, Davis, CA (United States). Dept. of Biomedical Engineering. Dept. of Chemical Engineering and Materials Science; Stupp, Samuel [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering. Dept. of Chemistry. Dept. of Medicine. Dept. of Biomedical Engineering; Szostak, Jack [Harvard Univ., Cambridge, MA (United States). Dept. of Chemistry and Chemical Biology

2016-01-21

Throughout human history, new materials have been the foundation of transformative technologies: from bronze, paper, and ceramics to steel, silicon, and polymers, each material has enabled far-reaching advances. Today, another new class of materials is emerging—one with both the potential to provide radically new functions and to challenge our notion of what constitutes a “material”. These materials would harvest, transduce, or dissipate energy to perform autonomous, dynamic functions that mimic the behaviors of living organisms. Herein, we discuss the challenges and benefits of creating “dissipative” materials that can potentially blur the boundaries between living and non-living matter.

Applications of Evolutionary Algorithms to Electromagnetic Materials Characterization and Design Problems

Science.gov (United States)

Frasch, Jonathan Lemoine

Determining the electrical permittivity and magnetic permeability of materials is an important task in electromagnetics research. The method using reflection and transmission scattering parameters to determine these constants has been widely employed for many years, ever since the work of Nicolson, Ross, and Weir in the 1970's. For general materials that are homogeneous, linear, and isotropic, the method they developed (the NRW method) works very well and provides an analytical solution. For materials which possess a metal backing or are applied as a coating to a metal surface, it can be difficult or even impossible to obtain a transmission measurement, especially when the coating is thin. In such a circumstance, it is common to resort to a method which uses two reflection type measurements. There are several such methods for free-space measurements, using multiple angles or polarizations for example. For waveguide measurements, obtaining two independent sources of information from which to extract two complex parameters can be a challenge. This dissertation covers three different topics. Two of these involve different techniques to characterize conductor-backed materials, and the third proposes a method for designing synthetic validation standards for use with standard NRW measurements. All three of these topics utilize modal expansions of electric and magnetic fields to analyze propagation in stepped rectangular waveguides. Two of the projects utilize evolutionary algorithms (EA) to design waveguide structures. These algorithms were developed specifically for these projects and utilize fairly recent innovations within the optimization community. The first characterization technique uses two different versions of a single vertical step in the waveguide. Samples to be tested lie inside the steps with the conductor reflection plane behind them. If the two reflection measurements are truly independent it should be possible to recover the values of two complex

Rational design of new materials using recombinant structural proteins: Current state and future challenges.

Science.gov (United States)

Sutherland, Tara D; Huson, Mickey G; Rapson, Trevor D

2018-01-01

Sequence-definable polymers are seen as a prerequisite for design of future materials, with many polymer scientists regarding such polymers as the holy grail of polymer science. Recombinant proteins are sequence-defined polymers. Proteins are dictated by DNA templates and therefore the sequence of amino acids in a protein is defined, and molecular biology provides tools that allow redesign of the DNA as required. Despite this advantage, proteins are underrepresented in materials science. In this publication we investigate the advantages and limitations of using proteins as templates for rational design of new materials. Crown Copyright © 2017. Published by Elsevier Inc. All rights reserved.

Role of Sex and the Environment in Moderating Weight Gain Due to Inadequate Sleep.

Science.gov (United States)

Coborn, Jamie E; Houser, Monica M; Perez-Leighton, Claudio E; Teske, Jennifer A

2017-12-01

The growing prevalence of obesity, inadequate sleep and sleep disorders together with the negative impact of lack of sleep on overall health highlights the need for therapies targeted towards weight gain due to sleep loss. Sex disparities in obesity and sleep disorders are present; yet, the role of sex is inadequately addressed and thus it is unclear whether sensitivity to sleep disruption differs between men and women. Like sex, environmental factors contribute to the development of obesity and poor sleep. The obesogenic environment is characterized by easy access to palatable foods and a low demand for energy expenditure in daily activities. These and other environmental factors are discussed, as they drive altered sleep or their interaction with food choice and intake can promote obesity. We discuss data that suggest differences in sleep patterns and responses to sleep disruption influence sex disparities in weight gain, and that enviromental disturbances alter sleep and interact with features of the obesogenic environment that together promote obesity.

Inadequate Sleep and Exercise Associated with Burnout and Depression Among Medical Students.

Science.gov (United States)

Wolf, Megan R; Rosenstock, Jason B

2017-04-01

The authors studied whether low levels of exercise or inadequate sleep correlated with higher levels of burnout and depression in medical students. Medical students of all years at the University of Pittsburgh School of Medicine, Pittsburgh, PA, USA, were invited to participate in an anonymous online survey in Fall 2012 and Winter 2013. Validated measures were used to assess exercise, sleep, burnout, and depression. Response rates were 28.7 % at the beginning of the school year and 22.6 % at the middle of the school year. Burnout rates overall were 22.4 % at the beginning of the year and 19.2 % in the middle of the year. Eight percent of students screened positive for depression at the beginning of the year and 9.3 % in the middle of the year. Decreased exercise frequency was significantly correlated with lower professional efficacy. Pathological sleepiness was significantly associated with a higher prevalence of burnout. Inadequate sleep correlated with significantly lower professional efficacy and higher exhaustion scores. Burnout was associated with a positive depression screen. Positive depression screening, pathological sleepiness, and sleeping less than 7 h a night were independent predictors of burnout. Sleep habits, exercise, and a positive depression screen were associated with burnout risk within the medical student population.

Development of integrated platform for computational material design

Energy Technology Data Exchange (ETDEWEB)

Kiyoshi, Matsubara; Kumi, Itai; Nobutaka, Nishikawa; Akifumi, Kato [Center for Computational Science and Engineering, Fuji Research Institute Corporation (Japan); Hideaki, Koike [Advance Soft Corporation (Japan)

2003-07-01

The goal of our project is to design and develop a problem-solving environment (PSE) that will help computational scientists and engineers develop large complicated application software and simulate complex phenomena by using networking and parallel computing. The integrated platform, which is designed for PSE in the Japanese national project of Frontier Simulation Software for Industrial Science, is defined by supporting the entire range of problem solving activity from program formulation and data setup to numerical simulation, data management, and visualization. A special feature of our integrated platform is based on a new architecture called TASK FLOW. It integrates the computational resources such as hardware and software on the network and supports complex and large-scale simulation. This concept is applied to computational material design and the project 'comprehensive research for modeling, analysis, control, and design of large-scale complex system considering properties of human being'. Moreover this system will provide the best solution for developing large and complicated software and simulating complex and large-scaled phenomena in computational science and engineering. A prototype has already been developed and the validation and verification of an integrated platform will be scheduled by using the prototype in 2003. In the validation and verification, fluid-structure coupling analysis system for designing an industrial machine will be developed on the integrated platform. As other examples of validation and verification, integrated platform for quantum chemistry and bio-mechanical system are planned.

Development of integrated platform for computational material design

International Nuclear Information System (INIS)

Kiyoshi, Matsubara; Kumi, Itai; Nobutaka, Nishikawa; Akifumi, Kato; Hideaki, Koike

2003-01-01

The goal of our project is to design and develop a problem-solving environment (PSE) that will help computational scientists and engineers develop large complicated application software and simulate complex phenomena by using networking and parallel computing. The integrated platform, which is designed for PSE in the Japanese national project of Frontier Simulation Software for Industrial Science, is defined by supporting the entire range of problem solving activity from program formulation and data setup to numerical simulation, data management, and visualization. A special feature of our integrated platform is based on a new architecture called TASK FLOW. It integrates the computational resources such as hardware and software on the network and supports complex and large-scale simulation. This concept is applied to computational material design and the project 'comprehensive research for modeling, analysis, control, and design of large-scale complex system considering properties of human being'. Moreover this system will provide the best solution for developing large and complicated software and simulating complex and large-scaled phenomena in computational science and engineering. A prototype has already been developed and the validation and verification of an integrated platform will be scheduled by using the prototype in 2003. In the validation and verification, fluid-structure coupling analysis system for designing an industrial machine will be developed on the integrated platform. As other examples of validation and verification, integrated platform for quantum chemistry and bio-mechanical system are planned

Latest advances in supercapacitors: from new electrode materials to novel device designs.

Science.gov (United States)

Wang, Faxing; Wu, Xiongwei; Yuan, Xinhai; Liu, Zaichun; Zhang, Yi; Fu, Lijun; Zhu, Yusong; Zhou, Qingming; Wu, Yuping; Huang, Wei

2017-11-13

Notably, many significant breakthroughs for a new generation of supercapacitors have been reported in recent years, related to theoretical understanding, material synthesis and device designs. Herein, we summarize the state-of-the-art progress toward mechanisms, new materials, and novel device designs for supercapacitors. Firstly, fundamental understanding of the mechanism is mainly focused on the relationship between the structural properties of electrode materials and their electrochemical performances based on some in situ characterization techniques and simulations. Secondly, some emerging electrode materials are discussed, including metal-organic frameworks (MOFs), covalent organic frameworks (COFs), MXenes, metal nitrides, black phosphorus, LaMnO 3 , and RbAg 4 I 5 /graphite. Thirdly, the device innovations for the next generation of supercapacitors are provided successively, mainly emphasizing flow supercapacitors, alternating current (AC) line-filtering supercapacitors, redox electrolyte enhanced supercapacitors, metal ion hybrid supercapacitors, micro-supercapacitors (fiber, plane and three-dimensional) and multifunctional supercapacitors including electrochromic supercapacitors, self-healing supercapacitors, piezoelectric supercapacitors, shape-memory supercapacitors, thermal self-protective supercapacitors, thermal self-charging supercapacitors, and photo self-charging supercapacitors. Finally, the future developments and key technical challenges are highlighted regarding further research in this thriving field.

The Effectiveness of Scaffolding Design in Training Writing Skills Physics Teaching Materials

Directory of Open Access Journals (Sweden)

Parlindungan Sinaga

2015-01-01

Full Text Available Result of field studies showed low writing skill of teachers in teaching material. The root of the problem lies in their inability on translating description of teaching material into writing. This research focused on the effectiveness of scaffolding design. The scaffolding design was tested in the selected topics of physics courses for pre-service teachers through learning to write activity approach. The treatment effectiveness was determined by considering the effect size and normalized gain percentage, while the hypothesis was tested using “the Kruskal-Wallis test”. The research results showed that scaffolding between the stages of planning and translating plans into text was effective in improving pre-service physics teachers’ ability of writing physics teaching materials and was similarly effective in improving their conceptual understanding of the topics of electromagnetism, waves, and optics. Learning to write activity implemented in the course of physics with selected topics was effective in improving the ability of pre-service teachers in translating among different modes of representation and making multiple concept representations. The hypothesis test demonstrated that there was a significant difference in the abilities of writing teaching materials and conceptual understanding between experimental and control classes.

Development of Digital Materials Database for Design and Construction of New Power Plants

International Nuclear Information System (INIS)

Ren, Weiju

2008-01-01

To facilitate materials selection, structural design, and future maintenance of the Generation IV nuclear reactor systems, an interactive, internet accessible materials property database, dubbed Gen IV Materials Handbook, has been under development with the support of the United States Department of Energy. The Handbook will provide an authoritative source of information on structural materials needed for the development of various Gen IV nuclear reactor systems along with powerful data analysis and management tools. In this paper, the background, history, framework, major features, contents, and development strategy of the Gen IV Materials Handbook are discussed. Current development status and future plans are also elucidated.

IE Information Notice No. 85-75: Improperly installed instrumentation, inadequate quality control and inadequate postmodification testing

International Nuclear Information System (INIS)

Jordan, E.L.

1992-01-01

On June 10, 1985, the licensee informed the NRC Resident Inspector that for approximately 5 days LaSalle Unit 2 had been without the capability of automatic actuation of emergency core cooling (ECCS) and that for approximately 3 days during this period the plant had been without secondary containment integrity. The major cause of this condition was improper installation (the variable and reference legs were reversed) of the two reactor vessel level actuation switches which control Division 1 automatic depressurization system (ADS), low pressure core spray (LPCS), and reactor core isolation cooling (RCIC). On July 20, 1985, the Trojan Nuclear Power Plant tripped from 100% power because of a turbine trip that was caused by the loss of the unit auxiliary transformer. All systems functioned normally except that low suction pressure caused one auxiliary feedwater pump to trip and then the other auxiliary feedwater pump to trip after restart of the first auxiliary feedwater pump. The cause of the trips of the auxiliary feedwater pumps can be traced back to improper postmodification adjustment and inadequate postmodification testing following retrofit of environmentally qualified controllers for the auxiliary feedwater system. The auxiliary feedwater pump trips on low suction pressure were caused by excessive combined flow from the two auxiliary feedwater pumps that draw from a single header from the condensate storage tank. The flow control valves were open farther than required after new environmentally qualified controllers had been installed during a recent refueling outage

Healthcare professionals' perceptions on the emotional impact of having an inadequate response to antidepressant medications: survey and prospective patient audit.

Science.gov (United States)

Mago, Rajnish; Fagiolini, Andrea; Weiller, Emmanuelle; Weiss, Catherine

2018-01-01

Despite the availability of effective antidepressants, about half of patients with major depressive disorder (MDD) display an inadequate response to their initial treatment. A large patient survey recently reported that 29.8% of MDD patients experiencing an inadequate treatment response felt frustrated about their medication and 19.2% were frustrated with their healthcare provider. This survey and chart audit evaluated healthcare professionals' (HCP) views on the emotional impact of having an inadequate response to antidepressant medication. HCPs who frequently treat patients with MDD completed a survey and chart audit of their MDD patients currently experiencing an inadequate response to antidepressant treatment. 287 HCPs completed 1336 chart audits. HCPs reported that 38% of their patients were trusting/accepting of their MDD medications and 41% of their patients trusted/felt confident with their healthcare provision. Conversely, HCPs reported that 11% of their patients were frustrated with their medication and 5% with their healthcare benefits. HCPs cited impact on daily life (53%) and treatment issues (lack of efficacy and side effects; 50%) as the main drivers for their patients' feelings of frustration. When HCPs recognized patients' feelings of frustration, the top concerns of the HCPs were worsening of symptoms (43%) and non-compliance (41%). This survey and chart audit highlights the emotional burden associated with inadequate responses to MDD treatment in addition to persistent symptoms. Differences between the views of the HCPs and patients are highlighted and suggest that HCPs may underestimate the full impact that having to try numerous medications has on their patients.

Systematic design of phononic band-gap materials and structures by topology optimization

DEFF Research Database (Denmark)

Sigmund, Ole; Jensen, Jakob Søndergaard

2003-01-01

Phononic band-gap materials prevent elastic waves in certain frequency ranges from propagating, and they may therefore be used to generate frequency filters, as beam splitters, as sound or vibration protection devices, or as waveguides. In this work we show how topology optimization can be used...... to design and optimize periodic materials and structures exhibiting phononic band gaps. Firstly, we optimize infinitely periodic band-gap materials by maximizing the relative size of the band gaps. Then, finite structures subjected to periodic loading are optimized in order to either minimize the structural...

25 CFR 170.811 - What happens if lack of funds results in inadequate maintenance?

Science.gov (United States)

2010-04-01

... maintenance? 170.811 Section 170.811 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER INDIAN RESERVATION ROADS PROGRAM BIA Road Maintenance § 170.811 What happens if lack of funds results in inadequate maintenance? If BIA determines that an IRR transportation facility is not being...

Examining the Relationship Between Children's ADHD Symptomatology and Inadequate Parenting: The Role of Household Chaos.

Science.gov (United States)

Wirth, Andrea; Reinelt, Tilman; Gawrilow, Caterina; Schwenck, Christina; Freitag, Christine M; Rauch, Wolfgang A

2017-02-01

This study examines the interrelations of parenting practices, emotional climate, and household chaos in families with children with and without ADHD. In particular, indirect pathways from children's ADHD symptomatology to inadequate parenting and negative emotional climate via household chaos were investigated. Parenting, emotional climate, and household chaos were assessed using questionnaires and a speech sample of parents of 31 children with and 53 without ADHD, aged 7 to 13 years. Group differences were found for certain parenting dimensions, the parent-child relationship, critical comments, and household chaos. While we found significant indirect effects between children's ADHD and certain parenting dimensions through household chaos, no effects were found for any aspect of emotional climate. Children's ADHD symptoms translate into inadequate parenting through household chaos, which underlines the need for interventions to improve household organization skills in parents of children with ADHD.

New Materials Design

National Research Council Canada - National Science Library

Voth, Gregory

1999-01-01

Progress has been made on several projects under the Challenge Project award. In the area of high energy density materials, calculations are under way on Al atoms embedded in clusters of H2 molecule...

Inadequate emergence after anesthesia: emergence delirium and hypoactive emergence in the Postanesthesia Care Unit.

Science.gov (United States)

Xará, Daniela; Silva, Acácio; Mendonça, Júlia; Abelha, Fernando

2013-09-01

To evaluate the frequency, determinants, and outcome of inadequate emergence after elective surgery in the Postanesthesia Care Unit (PACU). Prospective observational study. 12-bed PACU of a tertiary-care hospital in a major metropolitan area. 266 adult patients admitted to the PACU. To evaluate inadequate emergence, the Richmond Agitation and Sedation Scale (RASS) was administered to patients 10 minutes after their admission to the PACU. Demographic data, perioperative variables, and postoperative length of stay (LOS) in the PACU and the hospital were recorded. 40 (15%) patients showed symptoms of inadequate emergence: 17 patients (6.4%) screened positive for emergence delirium and 23 patients (8.6%) showed hypoactive emergence. Determinants of emergence delirium were longer duration of preoperative fasting (P = 0.001), higher visual analog scale (VAS) scores for pain (P = 0.002), and major surgical risk (P = 0.001); these patients had a higher frequency of postoperative delirium (P = 0.017) and had higher nausea VAS score 6 hours after surgery (P = 0.001). Determinants of hypoactive emergence were duration of surgery (P = 0.003), amount of crystalloids administered during surgery (P = 0.002), residual neuromuscular block (P < 0.001), high-risk surgery (P = 0.002), and lower core temperature on PACU admission (P = 0.028); these patients also had more frequent residual neuromuscular block (P < 0.001) postoperative delirium (P < 0.001), and more frequent adverse respiratory events (P = 0.02). Patients with hypoactive emergence had longer PACU and hospital LOS. Preventable determinants for emergence delirium were higher postoperative pain scores and longer fasting times. Hypoactive emergence was associated with longer postoperative PACU and hospital LOSs. © 2013 Elsevier Inc. All rights reserved.

On the Constitutive Response Characterization for Composite Materials Via Data-Driven Design Optimization

Science.gov (United States)

John G. Michopoulos; John G. Hermanson; Athanasios lliopoulos; Samuel Lambrakos; Tomonari Furukawa

2011-01-01

In the present paper we focus on demonstrating the use of design optimization for the constitutive characterization of anisotropic material systems such as polymer matrix composites, with or without damage. All approaches are based on the availability of experimental data originating from mechatronic material testing systems that can expose specimens to...

Pre-conceptual design activities for the materials plasma exposure experiment

International Nuclear Information System (INIS)

Lumsdaine, Arnold; Rapp, Juergen; Varma, Venugopal; Bjorholm, Thomas; Bradley, Craig; Caughman, John; Duckworth, Robert; Goulding, Richard; Graves, Van; Giuliano, Dominic; Lessard, Timothy; McGinnis, Dean; Meitner, Steven

2016-01-01

Highlights: • The development of long-pulse nuclear fusion devices requires testing plasma facing components at reactor relevant conditions. • The pre-conceptual design of a proposed linear plasma facility is presented. • Engineering considerations for multiple systems—plasma source and heating, magnet, vacuum, water cooling, and target, are presented. - Abstract: The development of next step fusion facilities such as DEMO or a Fusion Nuclear Science Facility (FNSF) requires first closing technology gaps in some critical areas. Understanding the material-plasma interface is necessary to enable the development of divertors for long-pulse plasma facilities. A pre-conceptual design for a proposed steady-state linear plasma device, the Materials Plasma Exposure Experiment (MPEX), is underway. A helicon plasma source along with ion cyclotron and electron Bernstein wave heating systems will produce ITER divertor relevant plasma conditions with steady-state parallel heat fluxes of up to 40 MW/m"2 with ion fluxes up to 10"2"4/m"2 s on target. Current plans are for the device to use superconducting magnets to produce 1–2 T fields. As a steady-state device, active cooling will be required for components that interact with the plasma (targets, limiters, etc.), as well as for other plasma facing components (transport regions, vacuum tanks, diagnostic ports). Design concepts for the vacuum system, the cooling system, and the plasma heating systems have been completed. The device will include the capability for handling samples that have been neutron irradiated in order to consider the multivariate effects of neutrons, plasma, and high heat-flux on the microstructure of divertor candidate materials. A vacuum cask, which can be disconnected from the high field environment in order to perform in-vacuo diagnosis of the surface evolution is also planned for the facility.

Pre-conceptual design activities for the materials plasma exposure experiment

Energy Technology Data Exchange (ETDEWEB)

Lumsdaine, Arnold, E-mail: lumsdainea@ornl.gov; Rapp, Juergen; Varma, Venugopal; Bjorholm, Thomas; Bradley, Craig; Caughman, John; Duckworth, Robert; Goulding, Richard; Graves, Van; Giuliano, Dominic; Lessard, Timothy; McGinnis, Dean; Meitner, Steven

2016-11-01

Highlights: • The development of long-pulse nuclear fusion devices requires testing plasma facing components at reactor relevant conditions. • The pre-conceptual design of a proposed linear plasma facility is presented. • Engineering considerations for multiple systems—plasma source and heating, magnet, vacuum, water cooling, and target, are presented. - Abstract: The development of next step fusion facilities such as DEMO or a Fusion Nuclear Science Facility (FNSF) requires first closing technology gaps in some critical areas. Understanding the material-plasma interface is necessary to enable the development of divertors for long-pulse plasma facilities. A pre-conceptual design for a proposed steady-state linear plasma device, the Materials Plasma Exposure Experiment (MPEX), is underway. A helicon plasma source along with ion cyclotron and electron Bernstein wave heating systems will produce ITER divertor relevant plasma conditions with steady-state parallel heat fluxes of up to 40 MW/m{sup 2} with ion fluxes up to 10{sup 24}/m{sup 2} s on target. Current plans are for the device to use superconducting magnets to produce 1–2 T fields. As a steady-state device, active cooling will be required for components that interact with the plasma (targets, limiters, etc.), as well as for other plasma facing components (transport regions, vacuum tanks, diagnostic ports). Design concepts for the vacuum system, the cooling system, and the plasma heating systems have been completed. The device will include the capability for handling samples that have been neutron irradiated in order to consider the multivariate effects of neutrons, plasma, and high heat-flux on the microstructure of divertor candidate materials. A vacuum cask, which can be disconnected from the high field environment in order to perform in-vacuo diagnosis of the surface evolution is also planned for the facility.

Sustainable hydrogen - A challenge for materials science and equipment design

International Nuclear Information System (INIS)

Duta, Anca; Enesca, Alexandru Ioan; Perniu, Dana

2006-01-01

Full text: Hydrogen is the ideal fuel, considering its fully non-polluting by-products. Still, in discussions on 'sustainable hydrogen', there must be considered all the steps implied in hydrogen production, storage and use and the overall energy balance represents the real starting point of evaluating the sustainability. So far, hydrogen production is related to rather energy-consuming processes; extended research is devoted to develop high efficiency processes, but the industrial hydrogen production makes use of either large electrical or thermal energy amounts. Hydrogen production via water photolysis represents, consequently a viable alternative although many steps have to be elaborated to reached the industrial scale of these processes. Hydrogen storing represents another problem that affects its application; a safe storage way, in metal hydrides, is still under intensive research all over the world. The group of the Centre of Product Design for Sustainable Development is engaged in research for developing a laboratory photolyser, able to produce hydrogen and to offer an efficient storage alternative. The photolyser is a photo-electrochemical cell, and the efficiency of the photolysis process depends on several factors: - the photo-electrodes: thin films of wide band gap semiconductors with tailored properties; - the aqueous environment, with effect on the electrode materials properties and stability; - the external bias; - the cell design. The paper focuses mainly on the photo-electrode materials that were tested. The influence of the composition, crystalline and defect structure, of the morphology and of the interfaces on the photolysis process are reviewed. The effect of the pH in the aqueous media is discussed along with the stability of the materials and the reversibility of the adsorption/desorption processes. The design criteria that must be fulfilled in developing the photolyser are also discussed. (authors)

Materials issues in the design of the ITER first wall, blanket, and divertor

International Nuclear Information System (INIS)

Mattas, R.F.; Smith, D.L.; Wu, C.H.; Shatalov, G.

1992-01-01

During the ITER conceptual design study, a property data base was assembled, the key issues were identified, and a comprehensive R ampersand D plan was formulated to resolve these issues. The desired properties of candidate ITER divertor, first wall, and blanket materials are briefly reviewed, and the major materials issues are presented. Estimates of the influence of materials properties on the performance limits of the first wall, blanket, and divertor are presented

7 CFR 1717.605 - Design standards, plans and specifications, construction standards, and RUS accepted materials.

Science.gov (United States)

2010-01-01

..., construction standards, and RUS accepted materials. 1717.605 Section 1717.605 Agriculture Regulations of the... standards, plans and specifications, construction standards, and RUS accepted materials. All borrowers... system design, construction standards, and the use of RUS accepted materials. Borrowers must comply with...

Alternative routes for highway shipments of radioactive materials and lessons learned from state designations

International Nuclear Information System (INIS)

1990-07-01

Pursuant to the Hazardous Materials Transportation Act (HMTA), the Department of Transportation (DOT) has promulgated a comprehensive set of regulations regarding the highway transportation of high-level radioactive materials. These regulations, under docket numbers HM-164 and HM-164A, establish interstate highways as the preferred routes for the transportation of radioactive materials within and through the states. The regulations also provide a methodology by which a state may select altemative routes. First, the state must establish a ''state routing agency'', defined as an entity authorized to use the state legal process to impose routing requirements on carriers of radioactive material (49 CFR 171.8). Once identified, the state routing agency must select routes in accordance with DOTs Guidelines for Selecting Preferred Highway Routes for Large Quantity Shipments of Radioactive Materials or an equivalent routing analysis. Adjoining states and localities should be consulted on the impact of proposed alternative routes as a prerequisite of final route selection. Lastly, the states must provide written notice to DOT of any alternative route designation before the routes are deemed effective. The purpose of this report is to discuss the ''lessons learned'' by the five states within the southern region that have designated alternative or preferred routes under the regulations of the Department of Transportation (DOT) established for the transportation of radioactive materials. The document was prepared by reviewing applicable federal laws and regulations, examining state reports and documents and contacting state officials and routing agencies involved in making routing decisions. In undertaking this project, the Southern States Energy Board hopes to reveal the process used by states that have designated alternative routes and thereby share their experiences (i.e., lessons learned) with other southern states that have yet to make designations

The first sustainable material designed for air particulate matter capture: An introduction to Azure Chemistry.

Science.gov (United States)

Zanoletti, A; Bilo, F; Depero, L E; Zappa, D; Bontempi, E

2018-07-15

This work presents a new porous material (SUNSPACE) designed for air particulate matter (PM) capture. It was developed in answer to the European Commission request of an innovative, affordable, and sustainable solution, based on design-driven material, to reduce the concentration of air particulate matter in urban areas. SUNSPACE material was developed from by-products and low-cost materials, such as silica fume and sodium alginate. Its capability to catch ultrafine PM was evaluated by different ad-hoc tests, considering diesel exhaust fumes and incense smoke PM. Despite the fact that procedures and materials can be designed for remediation, the high impact on the environment, for example in terms of natural resources consumption and emissions, are not usually considered. Instead, we believe that the technologies must be always evaluated in terms of material embodied energy (EE) and carbon footprint (CF). We define our approach to solve environment problems by a sustainable methodology "Azure Chemistry". For the SUNSPACE synthesis, the multi-criteria decision analysis was performed to select the best sustainable solution. The emissions and the energies involved in the synthesis of SUNSPACE material were evaluated with the Azure Chemistry approach, showing that this could be the best available technology to face the problem of capturing the PM in urban area. Copyright © 2018 Elsevier Ltd. All rights reserved.

Micro-/nanostructured multicomponent molecular materials: design, assembly, and functionality.

Science.gov (United States)

Yan, Dongpeng

2015-03-23

Molecule-based micro-/nanomaterials have attracted considerable attention because their properties can vary greatly from the corresponding macro-sized bulk systems. Recently, the construction of multicomponent molecular solids based on crystal engineering principles has emerged as a promising alternative way to develop micro-/nanomaterials. Unlike single-component materials, the resulting multicomponent systems offer the advantages of tunable composition, and adjustable molecular arrangement, and intermolecular interactions within their solid states. The study of these materials also supplies insight into how the crystal structure, molecular components, and micro-/nanoscale effects can influence the performance of molecular materials. In this review, we describe recent advances and current directions in the assembly and applications of crystalline multicomponent micro-/nanostructures. Firstly, the design strategies for multicomponent systems based on molecular recognition and crystal engineering principles are introduced. Attention is then focused on the methods of fabrication of low-dimensional multicomponent micro-/nanostructures. Their new applications are also outlined. Finally, we briefly discuss perspectives for the further development of these molecular crystalline micro-/nanomaterials. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sustainable manufacturing: Effect of material selection and design on the environmental impact in the manufacturing process

International Nuclear Information System (INIS)

Harun, Mohd Hazwan Syafiq; Salaam, Hadi Abdul; Taha, Zahari

2013-01-01

The environmental impact of a manufacturing process is also dependent on the selection of the material and design of a product. This is because the manufacturing of a product is directly connected to the amount of carbon emitted in consuming the electrical energy for that manufacturing process. The difference in the general properties of materials such as strength, hardness and impact will have significant effect on the power consumption of the machine used to complete the product. In addition the environmental impact can also be reduced if the proposed designs use less material. In this study, an LCA tool called Eco-It is used. Evaluate the environmental impact caused by manufacturing simple jig. A simple jig with 4 parts was used as a case study. Two experiments were carried out. The first experiment was to study the environmental effects of different material, and the second experiment was to study the environmental impact of different design. The materials used for the jig are Aluminium and mild steel. The results showed a decrease in the rate of carbon emissions by 60% when Aluminium is use instead from mild steel, and a decrease of 26% when the-design is modified

Exploring the effect of materials designed with augmented reality on language learners' vocabulary learning

Directory of Open Access Journals (Sweden)

Ekrem Solak

2015-07-01

Full Text Available The purpose of this study was to determine the motivational level of the participants in a language classroom towards course materials designed in accordance with augmented reality technology and to identify the correlation between academic achievement and motivational level. 130 undergraduate students from a state-run university in Turkey participated in this study and Turkish version of Material Motivational Survey was used to determine the undergraduate students’ motivational level about the materials which were designed with AR technology to teach English words at the elementary level. The results of this study suggested that AR technology materials had positive impact on increasing undergraduate students’ motivation towards vocabulary learning in language classroom. This study also signified that a positive significant correlation was found between academic achievement and the motivation in the use of AR technology in language classroom.

Computational methods for 2D materials: discovery, property characterization, and application design.

Science.gov (United States)

Paul, J T; Singh, A K; Dong, Z; Zhuang, H; Revard, B C; Rijal, B; Ashton, M; Linscheid, A; Blonsky, M; Gluhovic, D; Guo, J; Hennig, R G

2017-11-29

The discovery of two-dimensional (2D) materials comes at a time when computational methods are mature and can predict novel 2D materials, characterize their properties, and guide the design of 2D materials for applications. This article reviews the recent progress in computational approaches for 2D materials research. We discuss the computational techniques and provide an overview of the ongoing research in the field. We begin with an overview of known 2D materials, common computational methods, and available cyber infrastructures. We then move onto the discovery of novel 2D materials, discussing the stability criteria for 2D materials, computational methods for structure prediction, and interactions of monolayers with electrochemical and gaseous environments. Next, we describe the computational characterization of the 2D materials' electronic, optical, magnetic, and superconducting properties and the response of the properties under applied mechanical strain and electrical fields. From there, we move on to discuss the structure and properties of defects in 2D materials, and describe methods for 2D materials device simulations. We conclude by providing an outlook on the needs and challenges for future developments in the field of computational research for 2D materials.

Los Alamos National Laboratory new generation standard nuclear material storage container - the SAVY4000 design

International Nuclear Information System (INIS)

Stone, Timothy Amos

2010-01-01

Incidents involving release of nuclear materials stored in containers of convenience such as food pack cans, slip lid taped cans, paint cans, etc. has resulted in defense board concerns over the lack of prescriptive performance requirements for interim storage of nuclear materials. Los Alamos National Laboratory (LANL) has shared in these incidents and in response proactively moved into developing a performance based standard involving storage of nuclear material (RD003). This RD003 requirements document has sense been updated to reflect requirements as identified with recently issued DOE M 441.1-1 'Nuclear Material Packaging Manual'. The new packaging manual was issued at the encouragement of the Defense Nuclear Facilities Safety Board with a clear directive for protecting the worker from exposure due to loss of containment of stored materials. The Manual specifies a detailed and all inclusive approach to achieve a high level of protection; from package design and performance requirements, design life determinations of limited life components, authorized contents evaluations, and surveillance/maintenance to ensure in use package integrity over time. Materials in scope involve those stored outside an approved engineered-contamination barrier that would result in a worker exposure of in excess of 5 rem Committed Effective Does Equivalent (CEDE). Key aspects of meeting the challenge as developed around the SAVY-3000 vented storage container design will be discussed. Design performance and acceptance criteria against the manual, bounding conditions as established that the user must ensure are met to authorize contents in the package (based upon the activity of heat-source plutonium (90% Pu-238) oxide, which bounds the requirements for weapons-grade plutonium oxide), interface as a safety class system within the facility under the LANL plutonium facility DSA, design life determinations for limited life components, and a sense of design specific surveillance program

A statistical characterization method for damping material properties and its application to structural-acoustic system design

International Nuclear Information System (INIS)

Jung, Byung C.; Lee, Doo Ho; Youn, Byeng D.; Lee, Soo Bum

2011-01-01

The performance of surface damping treatments may vary once the surface is exposed to a wide range of temperatures, because the performance of viscoelastic damping material is highly dependent on operational temperature. In addition, experimental data for dynamic responses of viscoelastic material are inherently random, which makes it difficult to design a robust damping layout. In this paper a statistical modeling procedure with a statistical calibration method is suggested for the variability characterization of viscoelastic damping material in constrained-layer damping structures. First, the viscoelastic material property is decomposed into two sources: (I) a random complex modulus due to operational temperature variability, and (II) experimental/model errors in the complex modulus. Next, the variability in the damping material property is obtained using the statistical calibration method by solving an unconstrained optimization problem with a likelihood function metric. Two case studies are considered to show the influence of the material variability on the acoustic performances in the structural-acoustic systems. It is shown that the variability of the damping material is propagated to that of the acoustic performances in the systems. Finally, robust and reliable damping layout designs of the two case studies are obtained through the reliability-based design optimization (RBDO) amidst severe variability in operational temperature and the damping material

Benders decomposition for discrete material optimization in laminate design with local failure criteria

DEFF Research Database (Denmark)

Munoz, Eduardo; Stolpe, Mathias; Bendsøe, Martin P.

2009-01-01

in any discrete angle optimization design, or material selection problems. The mathematical modeling of this problem is more general than the one of standard topology optimization. When considering only two material candidates with a considerable difference in stiffness, it corresponds exactly...... to a topology optimization problem. The problem is modeled as a discrete design problem coming from a finite element discretization of the continuum problem. This discretization is made of shell or plate elements. For each element (selection domain), only one of the material candidates must be selected...... of the relaxed master problem and the current best compliance (weight) found get close enough with respect to certain tolerance. The method is investigated by computational means, using the finite element method to solve the analysis problems, and a commercial branch and cut method for solving the relaxed master...

Development of digital materials database for design and construction of new power plants

International Nuclear Information System (INIS)

Ren, W.

2008-01-01

To facilitate materials selection, structural design, and future maintenance of the Generation IV nuclear reactor systems, an interactive, internet accessible materials property database, dubbed Gen IV Materials Handbook, has been under development with the support of the United States Department of Energy. The Handbook will provide an authoritative source of information on structural materials needed for the development of various Gen IV nuclear reactor systems along with powerful data analysis and management tools. In this paper the background, history, framework, major features, contents, and development strategy of the Gen IV Materials Handbook are discussed. Current development status and future plans are also elucidated. (authors)

Participatory Communication Referred to Meta-Design Approach through the FleXpeaker™ Application of Innovative Material in Exhibition Design

Directory of Open Access Journals (Sweden)

Pei-Hsuan Su

2016-07-01

Full Text Available Modelling a communication system in material culture today always involves with objects, people, organizations, activities and interrelationships among them. The researcher suggests bringing together stakeholders engaged to exchange ideas, which the interactions relate to multiple professions and disciplines in a participatory scope of communication system. Owing to the invention of digital media, the status quo of images and sounds has revolutionized and caused changes of the mode of art exhibitions that produce activities and aesthetic concepts in terms of numerical representation, modularity, automation, visual variability and transcoding. Underlying a participatory-design approach, the research emphasizes a co-creative meta-interpretation of museum‟s visitors. In addition, the research delves further into the use of new media-FleXpeaker™ [ITRI], as the carrier. Combining art and design with innovative technology, the research focuses on examining design objects and innovative material which are applied in new media art and exhibition, in the hope to find new angles of participatory interpretation of the “integrated innovation” in curating an exhibition.

Representing Clarity: Using Universal Design Principles to Create Effective Hybrid Course Learning Materials

Science.gov (United States)

Spiegel, Cheri Lemieux

2012-01-01

This article describes how the author applied principles of universal design to hybrid course materials to increase student understanding and, ultimately, success. Pulling the three principles of universal design--consistency, color, and icon representation--into the author's Blackboard course allowed her to change the types of reading skills…

Design and Optimization of Composite Automotive Hatchback Using Integrated Material-Structure-Process-Performance Method

Science.gov (United States)

Yang, Xudong; Sun, Lingyu; Zhang, Cheng; Li, Lijun; Dai, Zongmiao; Xiong, Zhenkai

2018-03-01

The application of polymer composites as a substitution of metal is an effective approach to reduce vehicle weight. However, the final performance of composite structures is determined not only by the material types, structural designs and manufacturing process, but also by their mutual restrict. Hence, an integrated "material-structure-process-performance" method is proposed for the conceptual and detail design of composite components. The material selection is based on the principle of composite mechanics such as rule of mixture for laminate. The design of component geometry, dimension and stacking sequence is determined by parametric modeling and size optimization. The selection of process parameters are based on multi-physical field simulation. The stiffness and modal constraint conditions were obtained from the numerical analysis of metal benchmark under typical load conditions. The optimal design was found by multi-discipline optimization. Finally, the proposed method was validated by an application case of automotive hatchback using carbon fiber reinforced polymer. Compared with the metal benchmark, the weight of composite one reduces 38.8%, simultaneously, its torsion and bending stiffness increases 3.75% and 33.23%, respectively, and the first frequency also increases 44.78%.

The design and modeling of periodic materials with novel properties

Science.gov (United States)

Berger, Jonathan Bernard

Cellular materials are ubiquitous in our world being found in natural and engineered systems as structural materials, sound and energy absorbers, heat insulators and more. Stochastic foams made of polymers, metals and even ceramics find wide use due to their novel properties when compared to monolithic materials. Properties of these so called hybrid materials, those that combine materials or materials and space, are derived from the localization of thermomechanical stresses and strains on the mesoscale as a function of cell topology. The effects of localization can only be generalized in stochastic materials arising from their inherent potential complexity, possessing variations in local chemistry, microstructural inhomogeneity and topological variations. Ordered cellular materials on the other hand, such as lattices and honeycombs, make for much easier study, often requiring analysis of only a single unit-cell. Theoretical bounds predict that hybrid materials have the potential to push design envelopes offering lighter stiffer and stronger materials. Hybrid materials can achieve very low and even negative coefficients of thermal expansion (CTE) while retaining a relatively high stiffness -- properties completely unmatched by monolithic materials. In the first chapter of this thesis a two-dimensional lattice is detailed that possess near maximum stiffness, relative to the tightest theoretical bound, and low, zero and even appreciably negative thermal expansion. Its CTE and stiffness are given in closed form as a function of geometric parameters and the material properties. This result is confirmed with finite elements (FE) and experiment. In the second chapter the compressive stiffness of three-dimensional ordered foams, both closed and open cell, are predicted with FE and the results placed in property space in terms of stiffness and density. A novel structure is identified that effectively achieves theoretical bounds for Young's, shear and bulk modulus

Band Gap Optimization Design of Photonic Crystals Material

Science.gov (United States)

Yu, Y.; Yu, B.; Gao, X.

2017-12-01

The photonic crystal has a fundamental characteristic - photonic band gap, which can prevent light to spread in the crystals. This paper studies the width variation of band gaps of two-dimension square lattice photonic crystals by changing the geometrical shape of the unit cells’ inner medium column. Using the finite element method, we conduct numerical experiments on MATLAB 2012a and COMSOL 3.5. By shortening the radius in vertical axis and rotating the medium column, we design a new unit cell, with a 0.3*3.85e-7 vertical radius and a 15 degree deviation to the horizontal axis. The new cell has a gap 1.51 percent wider than the circle medium structure in TE gap and creates a 0.0124 wide TM gap. Besides, the experiment shows the first TM gap is partially overlapped by the second TE gap in gap pictures. This is helpful to format the absolute photonic band gaps and provides favorable theoretical basis for designing photonic communication material.

Ideology, capitalist division of labour and social role of the designer: a study on the production of materiality in fashion design

Directory of Open Access Journals (Sweden)

Joana Martins Contino

2016-12-01

Full Text Available Aiming to discuss about social division of labour and how it appears in the fashion design field, in addition to debate about the social role of fashion designer in the production chain, this paper presents two opposing notions that aim to explain important changes that have occurred in industrial society in the second half of twentieth century: “post-industrial society” of the author Daniel Bell, and “late capitalism” from Ernst Mandel. Each of these theories come from different ideological positions and impacts on the field of design with regard to theoretical production and the professional qualification and practices of designers. Thus, through bibliographic research, we began this paper with a reflection on the materiality and immateriality production in design. Then we confront these two important theoretical currents and relate them to others that we believe to be arising from one of them – "end of work", "design as a process" – and to objective and concrete issues of one of the design branches in which material production and the huge number of workers are undeniable: the fashion design field. Among these issues are the social division of labour and the propagation of the mythical notion of the individual creator, even propagated by the education system.

Materials design data for reduced activation martensitic steel type F82H

Energy Technology Data Exchange (ETDEWEB)

Tavassoli, A.-A.F. E-mail: tavassoli@cea.fr; Rensman, J.-W.; Schirra, M.; Shiba, K

2002-11-01

This paper presents materials data for design of ITER test blanket modules with the reduced activation ferritic martensitic steel type F82H as structural material. From the physical properties databases, variations of modulus of elasticity, density, thermal conductivity, thermal diffusivity, specific heat, mean and instantaneous linear coefficients of thermal expansion versus temperature are derived. Also reported are Poisson's ratio and magnetic properties. From the tension test results, nominal and minimum stress values of S{sub y} and S{sub u} are derived and used for calculation of allowable primary membrane stress intensity S{sub m}. Likewise, uniform and total elongations, as well as reduction of area data, are used for calculation of minimum and true ductility at rupture values. From the instrumented Charpy impact and fracture toughness test data, ductile to brittle transition temperature, toughness and behavior of material in different fracture modes are evaluated. The effect of specimen size and geometry are discussed but preference is given to standard size specimens. From the fatigue data, total strain range versus number of cycles to failure curves are plotted and used to derive fatigue design curves, using a reduction factor of 2 on strain and a reduction factor of 20 on number of cycles to failure. Cyclic hardening curves are also derived and compared with monotonic hardening curves. From the creep data, time dependent allowable stresses S{sub r} and S{sub t} are calculated. Combination of tension and creep results are used to deduce S{sub mt} and isochronus curves. Finally, irradiated and aged materials data are compared to insure that the safety margins incorporated in unirradiated design limits are not exceeded.

In silico design of porous polymer networks: high-throughput screening for methane storage materials.

Science.gov (United States)

Martin, Richard L; Simon, Cory M; Smit, Berend; Haranczyk, Maciej

2014-04-02

Porous polymer networks (PPNs) are a class of advanced porous materials that combine the advantages of cheap and stable polymers with the high surface areas and tunable chemistry of metal-organic frameworks. They are of particular interest for gas separation or storage applications, for instance, as methane adsorbents for a vehicular natural gas tank or other portable applications. PPNs are self-assembled from distinct building units; here, we utilize commercially available chemical fragments and two experimentally known synthetic routes to design in silico a large database of synthetically realistic PPN materials. All structures from our database of 18,000 materials have been relaxed with semiempirical electronic structure methods and characterized with Grand-canonical Monte Carlo simulations for methane uptake and deliverable (working) capacity. A number of novel structure-property relationships that govern methane storage performance were identified. The relationships are translated into experimental guidelines to realize the ideal PPN structure. We found that cooperative methane-methane attractions were present in all of the best-performing materials, highlighting the importance of guest interaction in the design of optimal materials for methane storage.

On design-oriented research and digital learning materials in higher education

NARCIS (Netherlands)

Hartog, R.J.M.

2012-01-01

The context of the research described in this thesis is formed by a number of research projects that were aimed at the design, development, implementation, use and evaluation of innovative digital learning materials. Most of these projects were carried out mainly within Wageningen University. In