WorldWideScience

Sample records for improved power capture

  1. Potential for improvement in power generation with post-combustion capture of CO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    C.A. Roberts; J. Gibbins; R. Panesar; G. Kelsall [Fluor Ltd., Camberley (United Kingdom)

    2005-07-01

    As part of a sponsored study for the IEA Greenhouse Gas R&D programme, (IEA GHG) the authors made studies of capturing carbon dioxide from flue gas using amine scrubbing and carbon dioxide compression. The integration of the capture and compression plants into modern, commercially available natural gas and ultra supercritical PF fired power plants was also studied. This paper presents costs of power production incorporating these technologies and includes a comparison of two commercial amine scrubbing technologies. These technologies are under constant development and rapid progress is being made by the technology owners in reducing the energy consumption of the amine recovery steps by means of novel flow-sheeting and thermal integration concepts. These are described. An analysis has been made of the best way to integrate amine scrubbing of flue gas into power plant cycles for natural gas and coal fired plants with the aim of reducing the parasitic energy loss in the power cycle to the lowest level possible. A brief discussion on technology stretch is presented which suggests ways in which these technologies may develop from now until 2020, with some estimates of likely production costs. 13 refs., 2 figs., 3 tabs.

  2. Field-test results using a nacelle-mounted lidar for improving wind turbine power capture by reducing yaw misalignment

    Science.gov (United States)

    Fleming, P. A.; Scholbrock, A. K.; Jehu, A.; Davoust, S.; Osler, E.; Wright, A. D.; Clifton, A.

    2014-06-01

    In this paper, a nacelle-mounted lidar was used to improve the yaw alignment of an experimental wind turbine. Using lidar-recorded data during normal operation, an error correction value for the nacelle vane wind direction measurement used in the yaw controller was determined. A field test was then conducted in which the turbine was operated with and without the correction applied to the yaw controller. Results demonstrated a significant increase in power capture. In addition, the study includes analysis on the impacts on loading of applying this yaw correction. The study demonstrates a successful application in field testing of using a nacelle-mounted lidar to improve turbine performance.

  3. Adaptive control algorithm for improving power capture of wind turbines in turbulent winds

    DEFF Research Database (Denmark)

    Diaz-Guerra, Lluis; Adegas, Fabiano Daher; Stoustrup, Jakob

    2012-01-01

    The standard wind turbine (WT) control law modifies the torque applied to the generator as a quadratic function of the generator speed (K!2) while blades are positioned at some optimal pitch angle (). The value of K and should be properly selected such that energy capture is increased. In practic...

  4. Variable-speed wind power system with improved energy capture via multilevel conversion

    Science.gov (United States)

    Erickson, Robert W.; Al-Naseem, Osama A.; Fingersh, Lee Jay

    2005-05-31

    A system and method for efficiently capturing electrical energy from a variable-speed generator are disclosed. The system includes a matrix converter using full-bridge, multilevel switch cells, in which semiconductor devices are clamped to a known constant DC voltage of a capacitor. The multilevel matrix converter is capable of generating multilevel voltage wave waveform of arbitrary magnitude and frequencies. The matrix converter can be controlled by using space vector modulation.

  5. Use of air jet vortex generators leading to improved energy capture and power regulation of a wind turbine

    Energy Technology Data Exchange (ETDEWEB)

    Oliver, A.; Wootton, L.R. [City Univ., London (United Kingdom); Prats, J. [Ecotecnia SCC Ltd. (United Kingdom)

    1997-06-01

    City University and Ecotecnia have recently completed a project funded by the European Union Joule II programme on the optimisation and control of wind turbines. The blade set of a 150 kW stall regulated wind turbine was modified with air jet vortex generators and tested at full scale. This was done primarily to increase its energy yield by reducing energy loss in the region of the power curve `knee`, but also to allow a degree of power regulation in high wind speeds. Of these, the former has so far been demonstrated successfully. (author)

  6. Reducing the cost of post combustion capture technology for pulverized coal power plants by flexible operation

    NARCIS (Netherlands)

    Kler, R.C.F. de; Verbaan, M.; Goetheer, E.L.V.

    2013-01-01

    Currently the low carbon prices, low Spreads and regulatory uncertainties hampers the business cases for coal-fired power plants with post-combustion capture (PCC) in Europe. Improvement of the business case of coal-fired power plants with post combustion capture requires a different approach in

  7. Reducing the cost of Post Combustion Capture technology for Pulverized Coal Power Plants by flexible operation

    NARCIS (Netherlands)

    De Kler, R.C.F.; Verbaan, M.; Goetheer, E.L.V.

    2013-01-01

    Currently the low carbon prices, low Spreads and regulatory uncertainties hampers the business cases for coal-fired power plants with post-combustion capture (PCC) in Europe. Improvement of the business case of coal-fired power plants with post combustion capture requires a different approach in

  8. Reducing the cost of Post Combustion Capture technology for Pulverized Coal Power Plants by flexible operation

    NARCIS (Netherlands)

    De Kler, R.C.F.; Verbaan, M.; Goetheer, E.L.V.

    2013-01-01

    Currently the low carbon prices, low Spreads and regulatory uncertainties hampers the business cases for coal-fired power plants with post-combustion capture (PCC) in Europe. Improvement of the business case of coal-fired power plants with post combustion capture requires a different approach in ter

  9. CO₂ Capture Membrane Process for Power Plant Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Toy, Lora [Research Triangle Inst. International, Research Triangle Park, NC (United States); Kataria, Atish [Research Triangle Inst. International, Research Triangle Park, NC (United States); Gupta, Raghubir [Research Triangle Inst. International, Research Triangle Park, NC (United States)

    2012-04-01

    Because the fleet of coal-fired power plants is of such importance to the nation's energy production while also being the single largest emitter of CO₂, the development of retrofit, post-combustion CO₂ capture technologies for existing and new, upcoming coal power plants will allow coal to remain a major component of the U.S. energy mix while mitigating global warming. Post-combustion carbon capture technologies are an attractive option for coal-fired power plants as they do not require modification of major power-plant infrastructures, such as fuel processing, boiler, and steam-turbine subsystems. In this project, the overall objective was to develop an advanced, hollow-fiber, polymeric membrane process that could be cost-effectively retrofitted into current pulverized coal-fired power plants to capture at least 90% of the CO₂ from plant flue gas with 95% captured CO₂ purity. The approach for this project tackled the technology development on three different fronts in parallel: membrane materials R&D, hollow-fiber membrane module development, and process development and engineering. The project team consisted of RTI (prime) and two industrial partners, Arkema, Inc. and Generon IGS, Inc. Two CO₂-selective membrane polymer platforms were targeted for development in this project. For the near term, a next-generation, high-flux polycarbonate membrane platform was spun into hollow-fiber membranes that were fabricated into both lab-scale and larger prototype (~2,200 ft²) membrane modules. For the long term, a new fluoropolymer membrane platform based on poly(vinylidene fluoride) [PVDF] chemistry was developed using a copolymer approach as improved capture membrane materials with superior chemical resistance to flue-gas contaminants (moisture, SO₂, NOx, etc.). Specific objectives were: - Development of new, highly chemically resistant, fluorinated polymers as membrane materials with minimum selectivity of 30 for CO₂ over N₂ and CO

  10. Technology qualification for IGCC power plant with CO2 Capture

    OpenAIRE

    Baig, Yasir

    2011-01-01

    Summary:This thesis presents the technology qualification plan for the integrated gasification combined cycle power plant (IGCC) with carbon dioxide capture based on DNV recommendations. Objectives of the thesis work were development of a qualification plan, heat balance, material balance and performance characteristics for IGCC with CO2 capture. GT PRO software by thermoflow was used for the development of heat balance, material balance and performance characteristics of power plant.IGCC wit...

  11. Improving Power Converter Reliability

    DEFF Research Database (Denmark)

    Ghimire, Pramod; de Vega, Angel Ruiz; Beczkowski, Szymon

    2014-01-01

    The real-time junction temperature monitoring of a high-power insulated-gate bipolar transistor (IGBT) module is important to increase the overall reliability of power converters for industrial applications. This article proposes a new method to measure the on-state collector?emitter voltage...... of a high-power IGBT module during converter operation, which may play a vital role in improving the reliability of the power converters. The measured voltage is used to estimate the module average junction temperature of the high and low-voltage side of a half-bridge IGBT separately in every fundamental...... is measured in a wind power converter at a low fundamental frequency. To illustrate more, the test method as well as the performance of the measurement circuit are also presented. This measurement is also useful to indicate failure mechanisms such as bond wire lift-off and solder layer degradation...

  12. Optimized post-combustion capture technology for power plants

    Energy Technology Data Exchange (ETDEWEB)

    Peter Moser; Sandra Schmidt; Georg Sieder; Hugo Garcia; Ilaria Ciattaglia; Dieter Mihailowitsch; Torsten Stoffregen [RWE Power AG, New Technologies, Essen (Germany)

    2009-07-01

    The construction and operation of the post-combustion capture pilot plant at RWE Power's lignite-fired power plant at Niederaussem is the first corner stone in a joint development programme of RWE Power, BASF and Linde that started in 2007. The pilot plant will be commissioned in mid-2009. The skid-mounted pilot plant - engineering, procurement and construction by procurement and construction by Linde - comprises all significant components of a large post-combustion capture plant but on a smaller scale. In the 18-month pilot plant testing programme optimized new solvents for the capture process will be evaluated. These solvents were selected by BASF in a multi-step procedure, starting with a pre-selection, followed by lab-screening, and finalized by mini plant runs. The pilot plant will validate the performance of some capture process optimization measures that are implemented to increase the overall efficiency and reduce the costs of a commercial capture plant. The results of the pilot plant testing will be directly used to optimize the capture process configuration for a base case power plant, a 1,100 MW lignite-fired power plant with lignite pre-drying technology. The development of the commercial capture plant needs an accurate analysis of all process steps to achieve a cost efficient plant design. Apart from energy efficiency, cost-effective equipment and the optimization of plant interfaces and plant configuration are also key factors to reach the ambitious goals of this project. Based on the results of the pilot plant tests and the full-scale design study, a demonstration plant concept will be developed to prove all innovative optimization measures and to avoid the risks involved in direct up-scaling from the pilot plant to the commercial plant scale without an intermediate step. 8 figs.

  13. Inorganic membranes for carbon capture and power generation

    Science.gov (United States)

    Snider, Matthew T.

    Inorganic membranes are under consideration for cost-effective reductions of carbon emissions from coal-fired power plants, both in the capture of pollutants post-firing and in the direct electrochemical conversion of coal-derived fuels for improved plant efficiency. The suitability of inorganic membrane materials for these purposes stems as much from thermal and chemical stability in coal plant operating conditions as from high performance in gas separations and power generation. Hydrophilic, micro-porous zeolite membrane structures are attractive for separating CO2 from N2 in gaseous waste streams due to the attraction of CO2 to the membrane surface and micropore walls that gives the advantage to CO2 transport. Recent studies have indicated that retention of the templating agent used in zeolite synthesis can further block N2 from the micropore interior and significantly improve CO2/N2 selectivity. However, the role of the templating agent in micro-porous transport has not been well investigated. In this work, gas sorption studies were conducted by high-pressure thermo-gravimetric analysis on Zeolite Y membrane materials to quantify the effect of the templating agent on CO2, N2, and H2O adsorption/desorption, as well as to examine the effect of humidification on overall membrane performance. In equilibrium conditions, the N2 sorption enthalpy was nearly unchanged by the presence of the templating agent, but the N2 pore occupation was reduced ˜1000x. Thus, the steric nature of the blocking of N2 from the micropores by the templating agent was confirmed. CO2 and H2O sorption enthalpies were similarly unaffected by the templating agent, and the micropore occupations were only reduced as much as the void volume taken up by the templating agent. Thus, the steric blocking effect did not occur for molecules more strongly attracted to the micropore walls. Additionally, in time-transient measurements the CO 2 and H2O mobilities were significantly enhanced by the presence

  14. Capture technologies: Improvements and promising developments

    NARCIS (Netherlands)

    Blomen, E.; Hendriks, C.; Neele, F.

    2009-01-01

    In this status report we want to provide a comprehensive overview of the current status and promising technologies of CO2 capture by means of a literature review, in-house knowledge and interviews. We describe the technology, bottlenecks towards implementation and potential use. The results will be

  15. Power theories for improved power quality

    CERN Document Server

    Pasko, Marian

    2012-01-01

    Power quality describes a set of parameters of electric power and the load’s ability to function properly under specific conditions. It is estimated that problems relating to power quality costs the European industry hundreds of billions of Euros annually. In contrast, financing for the prevention of these problems amount to fragments of these costs. Power Theories for Improved Power Quality addresses this imbalance by presenting and assessing a range of methods and problems related to improving the quality of electric power supply. Focusing particularly on active compensators and the DSP based control algorithms, Power Theories for Improved Power Quality introduces the fundamental problems of electrical power. This introduction is followed by chapters which discuss: •‘Power theories’ including their historical development and application to practical problems, •operational principles of active compensator’s DSP control based algorithms using examples and results from laboratory research, and •t...

  16. Microelectronics improves power electronics

    Energy Technology Data Exchange (ETDEWEB)

    Diehl, R.

    1982-07-01

    The share of electric energy consumed by electric drives - called power current - can be used more efficiently by using power electronic regulating processes. Lower cost for power electronic components and progress in circuit technology are the decisive factors for the widespread use of regulating units. Microelectronics permit a cost-beneficial control of power regulating units, are made them more attractive for the user. Technical and economic attractivity of power electronic regulating processes have increased. These processes are mainly used for adjusting engine speed to the other process engineering parameters like pressure, output or speed. Optimization of power-current consuming processes are expected to achieve an energy saving potential of 15 TWh by the year 1995.

  17. Increased Power Capture by Rotor Speed–Dependent Yaw Control of Wind Turbines

    DEFF Research Database (Denmark)

    Kragh, Knud Abildgaard; Fleming, Paul A.; Scholbrock, Andrew K.

    2013-01-01

    When extracting energy from the wind using upwind, horizontal-axis wind turbines, a primary condition for ensuring maximum power yield is the ability to align the rotor axis with the dominating wind direction. Attempts have been made to improve the yaw alignment of wind turbines by applying...... and tested. Results show that, with the correction scheme in place, the yaw alignment of the case turbine is improved and the yaw error is reduced to the vicinity of zero degrees. As a result of the improved yaw alignment, an increased power capture is observed for below-rated wind speeds....

  18. Power coupler kick of the TRIUMF ICM capture cavities

    Science.gov (United States)

    Yan, Fang; E. Laxdal, R.; Zvyagintsev, V.; Yu., Chao; C., Gong; Koscielniak, S.

    2011-06-01

    The TRIUMF Injector CryoModule (ICM) adapted two superconducting single cavities as the capture section for the low injecting energy of 100 keV electrons. Coupler kick induced beam deflection and projected emittance growth are one of the prime concerns of the beam stability, especially at low energies. In low energy applications, the electron velocity changes rapidly inside the cavity, which makes the numerical analysis much more complicated. The commonly used theoretical formulas of the direct integral or the Panofsky-Wenzel theorem is not suitable for the kick calculation of β < 1 electrons. Despite that, the above mentioned kick calculation method doesn't consider injecting electron energy, the beam offset due to the coupler kick may not be negligible because of the low injection energy even if the kick is optimized. Thus the beam dynamics code TRACK is used here for the simulation of the power coupler kick perturbation. The coupler kick can be compensated for by a judicious choice of the coupler position in successive cavities from upstream to downstream. The simulation shows that because of the adiabatic damping by the following superconducting 9-cell cavity, even for the worst orbit distortion case after two capture cavities, the kick is still acceptable at the exit of the ICM after reaching 10 MeV. This paper presents the analysis of the transverse kick and the projected emittance growth induced by the coupler for β < 1 electrons. The simulated results of the TRIUMF ICM capture cavities are described and presented.

  19. Power coupler kick of the TRIUMF ICM capture cavities

    Institute of Scientific and Technical Information of China (English)

    YAN Fang; R.E. Laxdal; V. Zvyagintsev; Yu. Chao; C. Gong; S. Koscielniak

    2011-01-01

    The TRIUMF Injector CryoModule (ICM) adapted two superconducting single cavities as the capture section for the low injecting energy of 100 keV electrons. Coupler kick induced beam deflection and projected emittance growth are one of the prime concerns of the beam stability, especially at low energies. In low energy applications, the electron velocity changes rapidly inside the cavity, which makes the numerical analysis much more complicated. The commonly used theoretical formulas of the direct integral or the Panofsky- Wenzel theorem is not suitable for the kick calculation of β <1 electrons. Despite that, the above mentioned kick calculation method doesn't consider injecting electron energy, the beam offset due to the coupler kick may not be negligible because of the low injection energy even if the kick is optimized. Thus the beam dynamics code TRACK is used here for the simulation of the power coupler kick perturbation. The coupler kick can be compensated for by a judicious choice of the coupler position in successive cavities from upstream to downstream. The simulation shows that because of the adiabatic damping by the following superconducting 9-cell cavity, even for the worst orbit distortion case after two capture cavities, the kick is still acceptable at the exit of the ICM after reaching 10 MeV. This paper presents the analysis of the transverse kick and the projected emittance growth induced by the coupler for β <1 electrons. The simulated results of the TRIUMF ICM capture cavities are described and presented.

  20. 75 FR 32171 - American Electric Power Service Corporation's Mountaineer Commercial Scale Carbon Capture and...

    Science.gov (United States)

    2010-06-07

    ... American Electric Power Service Corporation's Mountaineer Commercial Scale Carbon Capture and Storage... Power Initiative (CCPI) Program. AEP's Mountaineer Commercial Scale Carbon Capture and Storage Project (Mountaineer CCS II Project) would construct a commercial scale carbon dioxide (CO 2 ) capture and storage (CCS...

  1. Reducing Power Penalty Related to PostCombustion CO2 Capture in Coal Power Plants

    Directory of Open Access Journals (Sweden)

    Ramona Mihaela Negoi

    2011-09-01

    Full Text Available Considering the important role of coal in energy security and in the same time the growing need to reduce CO2 emissions, amine-based post-combustion CO2 capture is considered as one of the most proper technologies to be implemented in coal fired power plants as well in natural gas fired plants, refinery gas, cement plants etc.. The main challenge for CO2 post-combustion is reducing the energy demand of the process, especially for solvent regeneration. In this paper, the energy reduction potential when waste heat of flue gases is integrated in the CO2 capture configuration scheme is discussed. The results are compared with a conventional coal power plant configuration when low-steam pressure is extracted from the water-steam cycle of the power plant.

  2. Comprehensive Exergy Analysis of Three IGCC Power Plant Configurations with CO2 Capture

    Directory of Open Access Journals (Sweden)

    Nicholas S. Siefert

    2016-08-01

    Full Text Available We have conducted comprehensive exergy analyses of three integrated gasification combined cycle with carbon capture and storage (IGCC-CCS power plant configurations: (1 a baseline model using Selexol™ for H2S/CO2 removal; (2 a modified version that adds a H2-selective membrane before the Selexol™ acid gas removal system; and (3 a modified baseline version that uses a CO2-selective membrane before the Selexol™ acid gas removal system. While holding the coal input flow rate and the CO2 captured flow rates constant, it was determined that the H2-selective membrane case had a higher net power output (584 MW compared to the baseline (564 MW and compared to the CO2-selective membrane case (550 MW. Interestingly, the CO2-selective membrane case destroyed the least amount of exergy within the power plant (967 MW, compared with the Baseline case (999 MW and the H2-membrane case (972 MW. The main problem with the CO2-selective membrane case was the large amount of H2 (48 MW worth of H2 chemical exergy remaining within the supercritical CO2 that exits the power plant. Regardless of the CO2 capture process used, the majority of the exergy destruction occurred in the gasifier (305 MW and gas turbine (~380 MW subsystems, suggesting that these two areas should be key areas of focus of future improvements.

  3. Low-Carbon Economic Dispatching for Power Grid Integrated with Carbon Capture Power Plants and Wind Power System

    Directory of Open Access Journals (Sweden)

    Sheng Siqing

    2015-01-01

    Full Text Available Carbon emission characteristics of all kinds of power units are analyzed against the background of the low carbon economy. This paper introduces carbon trading in the dispatching model, gives full consideration to the benefit or cost of carbon emission and introduces carbon emission in the dispatching model as a decision variable so as to achieve the unity of the economy and the environmental protection of the dispatching model. A low carbon economic dispatching model is established based on multiple objectives, such as the lowest thermal power generation cost, the lowest carbon trading cost and the lowest carbon capture power plant operation cost. Load equalization, output constraint of power unit, ramping constraint, spinning reserve constraint and carbon capture efficiency constraint should be taken into account in terms of constraint conditions. The model is solved by the particle swarm optimization based on dynamic exchange and density distance. The fact that the introduction of carbon trading can effectively reduce the level of carbon emission and increase the acceptance level of wind power is highlighted through the comparison of the results of three models’ computational examples. With the carbon trading mechanism, carbon capture power plants with new technologies are able to give full play to the advantage of reducing carbon emission and wind curtailment so as to promote the development of the energy conservation and emission reduction technology and reduce the total cost of the dispatching system.

  4. Membrane Process to Capture CO{sub 2} from Coal-Fired Power Plant Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Merkel, Tim; Wei, Xiaotong; Firat, Bilgen; He, Jenny; Amo, Karl; Pande, Saurabh; Baker, Richard; Wijmans, Hans; Bhown, Abhoyjit

    2012-03-31

    This final report describes work conducted for the U.S. Department of Energy National Energy Technology Laboratory (DOE NETL) on development of an efficient membrane process to capture carbon dioxide (CO{sub 2}) from power plant flue gas (award number DE-NT0005312). The primary goal of this research program was to demonstrate, in a field test, the ability of a membrane process to capture up to 90% of CO{sub 2} in coal-fired flue gas, and to evaluate the potential of a full-scale version of the process to perform this separation with less than a 35% increase in the levelized cost of electricity (LCOE). Membrane Technology and Research (MTR) conducted this project in collaboration with Arizona Public Services (APS), who hosted a membrane field test at their Cholla coal-fired power plant, and the Electric Power Research Institute (EPRI) and WorleyParsons (WP), who performed a comparative cost analysis of the proposed membrane CO{sub 2} capture process. The work conducted for this project included membrane and module development, slipstream testing of commercial-sized modules with natural gas and coal-fired flue gas, process design optimization, and a detailed systems and cost analysis of a membrane retrofit to a commercial power plant. The Polaris? membrane developed over a number of years by MTR represents a step-change improvement in CO{sub 2} permeance compared to previous commercial CO{sub 2}-selective membranes. During this project, membrane optimization work resulted in a further doubling of the CO{sub 2} permeance of Polaris membrane while maintaining the CO{sub 2}/N{sub 2} selectivity. This is an important accomplishment because increased CO{sub 2} permeance directly impacts the membrane skid cost and footprint: a doubling of CO{sub 2} permeance halves the skid cost and footprint. In addition to providing high CO{sub 2} permeance, flue gas CO{sub 2} capture membranes must be stable in the presence of contaminants including SO{sub 2}. Laboratory tests showed no

  5. Power Quality Improvement Using UPQC

    Directory of Open Access Journals (Sweden)

    K. Kalaipriya

    2014-05-01

    Full Text Available This paper presents the power quality improvement using UPQC. UPQC consists of series inverter, shunt inverter and capacitance. Every inverter connected with pulse generator for switching on. UPQC is especially obtained to resolve different kind of power quality drawback like reactive power compensation, voltage interruption and harmonics. DVR is connected in series to deliver the active and reactive power to distribution network. DC-link capacitors stay high as a result of the DVR needs a minimum amount of DC-link voltage to compensate sag. So, DC –link voltage is connected with PV module to reduce the cost. Design of UPQC device with multi-bus system obtained using MATLAB/SIMULINK and simulation results are mentioned to support the developed conception.

  6. Economic Comparison of Three Gas Separation Technologies for CO2 Capture from Power Plant Flue Gas

    Institute of Scientific and Technical Information of China (English)

    YANG Hongjun; FAN Shuanshi; LANG Xuemei; WANG Yanhong; NIE Jianghua

    2011-01-01

    Three gas separation technologies,chemical absorption,membrane separation and pressure swing adsorption,are usually applied for CO2 capture from flue gas in coal-fired power plants.In this work,the costs of the three technologies are analyzed and compared.The cost for chemical absorption is mainly from $30 to $60 per ton(based on CO2 avoided),while the minimum value is $10 per ton(based on CO2 avoided).As for membrane separation and pressure swing adsorption,the costs are $50 to $78 and $40 to $63 per ton(based on CO2 avoided),respectively.Measures are proposed to reduce the cost of the three technologies.For CO2 capture and storage process,the CO2 recovery and purity should be greater than 90%.Based on the cost,recovery,and purity,it seems that chemical absorption is currently the most cost-effective technology for CO2 capture from flue gas from power plants.However,membrane gas separation is the most promising alternative approach in the future,provided that membrane performance is further improved.

  7. Improved Actinide Neutron Capture Cross Sections Using Accelerator Mass Spectrometry

    Science.gov (United States)

    Bauder, W.; Pardo, R. C.; Kondev, F. G.; Kondrashev, S.; Nair, C.; Nusair, O.; Palchan, T.; Scott, R.; Seweryniak, D.; Vondrasek, R.; Collon, P.; Paul, M.; Youinou, G.; Salvatores, M.; Palmotti, G.; Berg, J.; Maddock, T.; Imel, G.

    2014-09-01

    The MANTRA (Measurement of Actinide Neutron TRAnsmutations) project will improve energy-integrated neutron capture cross section data across the actinide region. These data are incorporated into nuclear reactor models and are an important piece in understanding Generation IV reactor designs. We will infer the capture cross sections by measuring isotopic ratios from actinide samples, irradiated in the Advanced Test Reactor at INL, with Accelerator Mass Spectrometry (AMS) at ATLAS (ANL). The superior sensitivity of AMS allows us to extract multiple cross sections from a single sample. In order to analyze the large number of samples needed for MANTRA and to meet the goal of extracting multiple cross sections per sample, we have made a number of modifications to the AMS setup at ATLAS. In particular, we are developing a technique to inject solid material into the ECR with laser ablation. With laser ablation, we can better control material injection and potentially increase efficiency in the ECR, thus creating less contamination in the source and reducing cross talk. I will present work on the laser ablation system and preliminary results from our AMS measurements. The MANTRA (Measurement of Actinide Neutron TRAnsmutations) project will improve energy-integrated neutron capture cross section data across the actinide region. These data are incorporated into nuclear reactor models and are an important piece in understanding Generation IV reactor designs. We will infer the capture cross sections by measuring isotopic ratios from actinide samples, irradiated in the Advanced Test Reactor at INL, with Accelerator Mass Spectrometry (AMS) at ATLAS (ANL). The superior sensitivity of AMS allows us to extract multiple cross sections from a single sample. In order to analyze the large number of samples needed for MANTRA and to meet the goal of extracting multiple cross sections per sample, we have made a number of modifications to the AMS setup at ATLAS. In particular, we are

  8. Reassessing the Efficiency Penalty from Carbon Capture in Coal-Fired Power Plants.

    Science.gov (United States)

    Supekar, Sarang D; Skerlos, Steven J

    2015-10-20

    This paper examines thermal efficiency penalties and greenhouse gas as well as other pollutant emissions associated with pulverized coal (PC) power plants equipped with postcombustion CO2 capture for carbon sequestration. We find that, depending on the source of heat used to meet the steam requirements in the capture unit, retrofitting a PC power plant that maintains its gross power output (compared to a PC power plant without a capture unit) can cause a drop in plant thermal efficiency of 11.3-22.9%-points. This estimate for efficiency penalty is significantly higher than literature values and corresponds to an increase of about 5.3-7.7 US¢/kWh in the levelized cost of electricity (COE) over the 8.4 US¢/kWh COE value for PC plants without CO2 capture. The results follow from the inclusion of mass and energy feedbacks in PC power plants with CO2 capture into previous analyses, as well as including potential quality considerations for safe and reliable transportation and sequestration of CO2. We conclude that PC power plants with CO2 capture are likely to remain less competitive than natural gas combined cycle (without CO2 capture) and on-shore wind power plants, both from a levelized and marginal COE point of view.

  9. Greener power generation technologies. Solutions for carbon capture

    Energy Technology Data Exchange (ETDEWEB)

    Reimuth, Oliver; Kremer, Hermann; Vortmeyer, Nicolas [Siemens AG, Erlangen (Germany)

    2011-07-01

    Fossil-based power generation will continue to account for a dominant share of over 50 % in the future energy mix. In order to meet the requirements of climate protection, a combination of highly-efficient, flexible combined cycle power plants and the use of CCS in coal-based power generation will be necessary. In addition to funding of the first demonstration projects comprehensive statutory framework and public acceptance are necessary for launching CCS technology. (orig.)

  10. Capturing low-carbon power system dynamics : Interactions between intermittent renewables and power plants with CO2 capture and storage

    NARCIS (Netherlands)

    Brouwer, A.S.

    2015-01-01

    Low-carbon power systems are needed by the year 2050 to meet climate change mitigation targets. This dissertation investigates the operational and economic feasibility of such future low-carbon power systems by simulating the Dutch and European power systems. Particular attention is paid to the impa

  11. Capturing low-carbon power system dynamics : Interactions between intermittent renewables and power plants with CO2 capture and storage

    NARCIS (Netherlands)

    Brouwer, Anne-Sjoerd

    2015-01-01

    Low-carbon power systems are needed by the year 2050 to meet climate change mitigation targets. This dissertation investigates the operational and economic feasibility of such future low-carbon power systems by simulating the Dutch and European power systems. Particular attention is paid to the

  12. Field Test Results of Using a Nacelle-Mounted Lidar for Improving Wind Energy Capture by Reducing Yaw Misalignment (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Fleming, P.; Scholbrock, A.; Wright, A.

    2014-11-01

    Presented at the Nordic Wind Power Conference on November 5, 2014. This presentation describes field-test campaigns performed at the National Wind Technology Center in which lidar technology was used to improve the yaw alignment of the Controls Advanced Research Turbine (CART) 2 and CART3 wind turbines. The campaigns demonstrated that whether by learning a correction function to the nacelle vane, or by controlling yaw directly with the lidar signal, a significant improvement in power capture was demonstrated.

  13. Improved power performance assessment methods

    Energy Technology Data Exchange (ETDEWEB)

    Frandsen, S.; Antoniou, I.; Dahlberg, J.A. [and others

    1999-03-01

    The uncertainty of presently-used methods for retrospective assessment of the productive capacity of wind farms is unacceptably large. The possibilities of improving the accuracy have been investigated and are reported. A method is presented that includes an extended power curve and site calibration. In addition, blockage effects with respect to reference wind speed measurements are analysed. It is found that significant accuracy improvements are possible by the introduction of more input variables such as turbulence and wind shear, in addition to mean wind speed and air density. Also, the testing of several or all machines in the wind farm - instead of only one or two - may provide a better estimate of the average performance. (au)

  14. Predicting the ultimate potential of natural gas SOFC power cycles with CO2 capture - Part B: Applications

    Science.gov (United States)

    Campanari, Stefano; Mastropasqua, Luca; Gazzani, Matteo; Chiesa, Paolo; Romano, Matteo C.

    2016-09-01

    An important advantage of solid oxide fuel cells (SOFC) as future systems for large scale power generation is the possibility of being efficiently integrated with processes for CO2 capture. Focusing on natural gas power generation, Part A of this work assessed the performances of advanced pressurised and atmospheric plant configurations (SOFC + GT and SOFC + ST, with fuel cell integration within a gas turbine or a steam turbine cycle) without CO2 separation. This Part B paper investigates such kind of power cycles when applied to CO2 capture, proposing two ultra-high efficiency plant configurations based on advanced intermediate-temperature SOFCs with internal reforming and low temperature CO2 separation process. The power plants are simulated at the 100 MW scale with a set of realistic assumptions about FC performances, main components and auxiliaries, and show the capability of exceeding 70% LHV efficiency with high CO2 capture (above 80%) and a low specific primary energy consumption for the CO2 avoided (1.1-2.4 MJ kg-1). Detailed results are presented in terms of energy and material balances, and a sensitivity analysis of plant performance is developed vs. FC voltage and fuel utilisation to investigate possible long-term improvements. Options for further improvement of the CO2 capture efficiency are also addressed.

  15. Carbon Dioxide Capture and Separation Techniques for Gasification-based Power Generation Point Sources

    Energy Technology Data Exchange (ETDEWEB)

    Pennline, H.W.; Luebke, D.R.; Jones, K.L.; Morsi, B.I. (Univ. of Pittsburgh, PA); Heintz, Y.J. (Univ. of Pittsburgh, PA); Ilconich, J.B. (Parsons)

    2007-06-01

    The capture/separation step for carbon dioxide (CO2) from large-point sources is a critical one with respect to the technical feasibility and cost of the overall carbon sequestration scenario. For large-point sources, such as those found in power generation, the carbon dioxide capture techniques being investigated by the in-house research area of the National Energy Technology Laboratory possess the potential for improved efficiency and reduced costs as compared to more conventional technologies. The investigated techniques can have wide applications, but the research has focused on capture/separation of carbon dioxide from flue gas (post-combustion from fossil fuel-fired combustors) and from fuel gas (precombustion, such as integrated gasification combined cycle or IGCC). With respect to fuel gas applications, novel concepts are being developed in wet scrubbing with physical absorption; chemical absorption with solid sorbents; and separation by membranes. In one concept, a wet scrubbing technique is being investigated that uses a physical solvent process to remove CO2 from fuel gas of an IGCC system at elevated temperature and pressure. The need to define an ideal solvent has led to the study of the solubility and mass transfer properties of various solvents. Pertaining to another separation technology, fabrication techniques and mechanistic studies for membranes separating CO2 from the fuel gas produced by coal gasification are also being performed. Membranes that consist of CO2-philic ionic liquids encapsulated into a polymeric substrate have been investigated for permeability and selectivity. Finally, dry, regenerable processes based on sorbents are additional techniques for CO2 capture from fuel gas. An overview of these novel techniques is presented along with a research progress status of technologies related to membranes and physical solvents.

  16. Thermal Integration of CO{sub 2} Compression Processes with Coal-Fired Power Plants Equipped with Carbon Capture

    Energy Technology Data Exchange (ETDEWEB)

    Edward Levy

    2012-06-29

    Coal-fired power plants, equipped either with oxycombustion or post-combustion CO{sub 2} capture, will require a CO{sub 2} compression system to increase the pressure of the CO{sub 2} to the level needed for sequestration. Most analyses show that CO{sub 2} compression will have a significant effect on parasitic load, will be a major capital cost, and will contribute significantly to reduced unit efficiency. This project used first principle engineering analyses and computer simulations to determine the effects of utilizing compressor waste heat to improve power plant efficiency and increase net power output of coal-fired power plants with carbon capture. This was done for units with post combustion solvent-based CO{sub 2} capture systems and for oxyfired power plants, firing bituminous, PRB and lignite coals. The thermal integration opportunities analyzed for oxycombustion capture are use of compressor waste heat to reheat recirculated flue gas, preheat boiler feedwater and predry high-moisture coals prior to pulverizing the coal. Among the thermal integration opportunities analyzed for post combustion capture systems are use of compressor waste heat and heat recovered from the stripper condenser to regenerate post-combustion CO{sub 2} capture solvent, preheat boiler feedwater and predry high-moisture coals. The overall conclusion from the oxyfuel simulations is that thermal integration of compressor heat has the potential to improve net unit heat rate by up to 8.4 percent, but the actual magnitude of the improvement will depend on the type of heat sink used and to a lesser extent, compressor design and coal rank. The simulations of a unit with a MEA post combustion capture system showed that thermal integration of either compressor heat or stripper condenser heat to preheat boiler feedwater would result in heat rate improvements from 1.20 percent to 4.19 percent. The MEA capture simulations further showed that partial drying of low rank coals, done in combination

  17. Membrane Process to Capture CO{sub 2} from Coal-Fired Power Plant Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Merkel, Tim; Wei, Xiaotong; Firat, Bilgen; He, Jenny; Amo, Karl; Pande, Saurabh; Baker, Richard; Wijmans, Hans; Bhown, Abhoyjit

    2012-03-31

    This final report describes work conducted for the U.S. Department of Energy National Energy Technology Laboratory (DOE NETL) on development of an efficient membrane process to capture carbon dioxide (CO{sub 2}) from power plant flue gas (award number DE-NT0005312). The primary goal of this research program was to demonstrate, in a field test, the ability of a membrane process to capture up to 90% of CO{sub 2} in coal-fired flue gas, and to evaluate the potential of a full-scale version of the process to perform this separation with less than a 35% increase in the levelized cost of electricity (LCOE). Membrane Technology and Research (MTR) conducted this project in collaboration with Arizona Public Services (APS), who hosted a membrane field test at their Cholla coal-fired power plant, and the Electric Power Research Institute (EPRI) and WorleyParsons (WP), who performed a comparative cost analysis of the proposed membrane CO{sub 2} capture process. The work conducted for this project included membrane and module development, slipstream testing of commercial-sized modules with natural gas and coal-fired flue gas, process design optimization, and a detailed systems and cost analysis of a membrane retrofit to a commercial power plant. The Polaris? membrane developed over a number of years by MTR represents a step-change improvement in CO{sub 2} permeance compared to previous commercial CO{sub 2}-selective membranes. During this project, membrane optimization work resulted in a further doubling of the CO{sub 2} permeance of Polaris membrane while maintaining the CO{sub 2}/N{sub 2} selectivity. This is an important accomplishment because increased CO{sub 2} permeance directly impacts the membrane skid cost and footprint: a doubling of CO{sub 2} permeance halves the skid cost and footprint. In addition to providing high CO{sub 2} permeance, flue gas CO{sub 2} capture membranes must be stable in the presence of contaminants including SO{sub 2}. Laboratory tests showed no

  18. Advanced virtual energy simulation training and research: IGCC with CO2 capture power plant

    Energy Technology Data Exchange (ETDEWEB)

    Zitney, S.; Liese, E.; Mahapatra, P.; Bhattacharyya, D.; Provost, G.

    2011-01-01

    AVESTAR Center is poised to develop a workforce well-prepared to operate and control commercial-scale gasification-based power plants capable of 90% pre-combustion CO{sub 2} capture and compression, as well as low sulfur, mercury, and NOx emissions. With additional support from the NETL-Regional University Alliance (NETL-RUA), the Center will educate and train engineering students and researchers by providing hands-on 'learning by operating' experience The AVESTAR Center also offers unique collaborative R&D opportunities in high-fidelity dynamic modeling, advanced process control, real-time optimization, and virtual plant simulation. Objectives and goals are aimed at safe and effective management of power generation systems for optimal efficiency, while protecting the environment. To add another dimension of realism to the AVESTAR experience, NETL will introduce an immersive training system with innovative three-dimensional virtual reality technology. Wearing a stereoscopic headset or eyewear, trainees will enter an interactive virtual environment that will allow them to move freely throughout the simulated 3-D facility to study and learn various aspects of IGCC plant operation, control, and safety. Such combined operator and immersive training systems go beyond traditional simulation and include more realistic scenarios, improved communication, and collaboration among co-workers.

  19. Power to fuel using electrolysis and CO2 capture

    DEFF Research Database (Denmark)

    Mogensen, Mogens Bjerg; Graves, Christopher R.; Chatzichristodoulou, Christodoulos

    2014-01-01

    Conversion of renewable electricity to synthetic fuel using electrolysis to produce at H2 and CO, which is furtherused to form liquid or gaseous fuel, called “power to fuel” or “power2fuel” has got a lot of attention recently.This is because synthetic fuels (synfuels) in the form CO2 neutral “green......” hydrocarbon fuels seem particularlybenign to replace the fossil fuels, and electrolysis seems to be a feasible step in production of green fuels. In particular, synthetic hydrocarbon based fuel will be necessary for the heavy transportation vehicles such as airplanes, ships, and trucks. More than 65...... % of the cost of H2 produced by electrolysis originates from electricity cost. How much more depends on the actual electricity price and depends further on efficiency, investment cost and lifetime of electrolyzer. Investment costs are inversely proportional the current density at a given cell voltage...

  20. Capturing Real-Time Power System Dynamics: Opportunities and Challenges

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Zhenyu; Zhou, Ning; Diao, Ruisheng; Wang, Shaobu; Elbert, Stephen T.; Meng, Da; Lu, Shuai

    2015-09-01

    The power grid evolves towards a new mix of generation and consumption that introduces new dynamic and stochastic behaviors. These emerging grid behaviors would invalidate the steady-state assumption in today’s state estimation – an essential function for real-time power grid operation. This paper examines this steady-state assumption and identifies the need for estimating dynamic states. Supporting technologies are presented as well as a proposed formulation for estimating dynamic states. Metrics for evaluating methods for solving the dynamic state estimation problem are proposed, with example results to illustrate the use of these metrics. The overall objective of this paper is to provide a basis that more research on this topic can follow.

  1. Cropland Capture: A Game to Improve Global Cropland through Crowdsourcing

    Science.gov (United States)

    Fritz, Steffen; Sturn, Tobias; See, Linda; Perger, Christoph; Schill, Christian; McCallum, Ian; Schepaschenko, Dmitry; Karner, Mathias; Dueruer, Martina; Kraxner, Florian; Obersteiner, Michael

    2014-05-01

    Accurate and reliable global cropland extent maps are essential for estimating and forecasting crop yield, in particular losses due to drought and production anomalies. Major questions surrounding energy futures and environmental change (EU and US biofuel target setting, determination of greenhouse gas emissions, REDD initiatives, and implications of climate change on crop production and productivity patterns) also require reliable information on the spatial distribution of cropland as well as crop types. Although global land cover maps identify cropland (which exist as one or more land cover categories), this information is currently not accurate enough for many applications. There are several ways of improving current cropland extent though hybrid approaches and by integrating information collected though Geo-Wiki (a global crowdsourcing platform) from very high resolution imagery such as that found on Google Earth. Another way of getting improved cropland extent maps would be to classify all very high resolution images found on Google Earth and to create a wall-to-wall map of cropland. This is a very ambitious task that would require a large number of individuals, like that found in massive multiplayer online games. For this reason we have developed a game called 'Cropland Capture'. The game can be played on a desktop, on a tablet (iPad or Android) or mobile phone (iPhone or Android) where the game mechanics are very simple. The player is provided with a satellite image or in-situ photo and they must determine if the image contains cropland or not. The game was launched in the middle of November 2013 and will run for 6 months, after which the weekly winners will be entered into a draw to win large prizes. To date we have collected more than 2.5 million areas, where we will continue to expand the sample to more locations around the world. Eventually the data will be used to calibrate and validate a new version of our global cropland map, where the latest version

  2. CO2 capture processes in power plants - Le captage du CO2 dans les centrales thermiques

    CERN Document Server

    Bouallou, Chakib

    2010-01-01

    This review is devoted to assess and compare various processes aiming at recover CO2 from power plants fed with natural gas (NGCC) and pulverized coal (PC). These processes are post combustion CO2 capture using chemical solvents, natural gas reforming for pre-combustion capture and oxy-fuel combustion with cryogenic recovery of CO2. These processes were evaluated to give some clues for choosing the best option for each type of power plant. The comparison of these various concepts suggests that, in the short and medium term, chemical absorption is the most interesting process for NGCC power plants. For CP power plants, oxy-combustion can be a very interesting option, as well as post-combustion capture by chemical solvents.

  3. Research and improvement on packet capture mechanism in linux for high-speed network

    Institute of Scientific and Technical Information of China (English)

    YANG Wu; FANG Bin-xing; YUN Xiao-chun; ZHANG Hong-li

    2005-01-01

    With the increasing enlargement of network scale and the rapid development of network techniques,large numbers of the network applications begin to appear. Packet capture plays an important role as one basic technique used in each field of the network applications. In a high-speed network, the heavy traffic of network transmission challenges the packet capture techniques. This paper does an in-depth analysis on the traditional packet capture mechanisms in Linux, and then measures the performance bottleneck in the process of packet capture. The methods for improving the packet capture performance are presented and an optimized packet capture scheme is also designed and implemented. The test demonstrates that the new packet capture mechanism (Libpacket) can greatly improve the packet capture performance of the network application systems in a highspeed network.

  4. CO2 post-combustion capture in coal-fired power plants integrated with solar systems

    Science.gov (United States)

    Carapellucci, R.; Giordano, L.; Vaccarelli, M.

    2015-11-01

    The majority of the World's primary energy consumption is still based on fossil fuels, representing the largest source of global CO2 emissions. According to the Intergovernmental Panel on Climate Change (IPCC), such emissions must be significantly reduced in order to avoid the dramatic consequences of global warming. A potential way to achieve this ambitious goal is represented by the implementation of CCS (Carbon Capture and Storage) technologies. However, the significant amount of energy required by the CCS systems still represents one the major barriers for their deployment. Focusing on post-combustion capture based on amine absorption, several interesting options have been investigated to compensate the energy losses due to solvent regeneration, also using renewable energy sources. One of the most promising is based on the use of concentrating solar power (CSP), providing a part of the energy requirement of the capture island. In this study the integration of a CSP system into a coal-fired power plant with CO2 postcombustion capture is investigated. Basically, a CSP system is used to support the heat requirement for amine regeneration, by producing saturated steam at low temperature. This allows to reduce or even eliminate the conventional steam extraction from the main power plant, affecting positively net power production and efficiency. The energy analysis of the whole system is carried out using the GateCycle software to simulate the coal-fired power plant and ChemCad platform for the CO2 capture process based on amine absorption.

  5. Improved reliability of power modules

    DEFF Research Database (Denmark)

    Baker, Nick; Liserre, Marco; Dupont, Laurent

    2014-01-01

    Power electronic systems play an increasingly important role in providing high-efficiency power conversion for adjustable-speed drives, power-quality correction, renewable-energy systems, energy-storage systems, and electric vehicles. However, they are often presented with demanding operating env...... temperature cycling conditions on the system. On the other hand, safety requirements in the aerospace and automotive industries place rigorous demands on reliability....

  6. Laser accelerated protons captured and transported by a pulse power solenoid

    Science.gov (United States)

    Burris-Mog, T.; Harres, K.; Nürnberg, F.; Busold, S.; Bussmann, M.; Deppert, O.; Hoffmeister, G.; Joost, M.; Sobiella, M.; Tauschwitz, A.; Zielbauer, B.; Bagnoud, V.; Herrmannsdoerfer, T.; Roth, M.; Cowan, T. E.

    2011-12-01

    Using a pulse power solenoid, we demonstrate efficient capture of laser accelerated proton beams and the ability to control their large divergence angles and broad energy range. Simulations using measured data for the input parameters give inference into the phase-space and transport efficiencies of the captured proton beams. We conclude with results from a feasibility study of a pulse power compact achromatic gantry concept. Using a scaled target normal sheath acceleration spectrum, we present simulation results of the available spectrum after transport through the gantry.

  7. Assessment of Solid Sorbent Systems for Post-Combustion Carbon Dioxide Capture at Coal-Fired Power Plants

    Science.gov (United States)

    Glier, Justin C.

    In an effort to lower future CO2 emissions, a wide range of technologies are being developed to scrub CO2 from the flue gases of fossil fuel-based electric power and industrial plants. This thesis models one of several early-stage post-combustion CO2 capture technologies, solid sorbent-based CO2 capture process, and presents performance and cost estimates of this system on pulverized coal power plants. The spreadsheet-based software package Microsoft Excel was used in conjunction with AspenPlus modelling results and the Integrated Environmental Control Model to develop performance and cost estimates for the solid sorbent-based CO2 capture technology. A reduced order model also was created to facilitate comparisons among multiple design scenarios. Assumptions about plant financing and utilization, as well as uncertainties in heat transfer and material design that affect heat exchanger and reactor design were found to produce a wide range of cost estimates for solid sorbent-based systems. With uncertainties included, costs for a supercritical power plant with solid sorbent-based CO2 capture ranged from 167 to 533 per megawatt hour for a first-of-a-kind installation (with all costs in constant 2011 US dollars) based on a 90% confidence interval. The median cost was 209/MWh. Post-combustion solid sorbent-based CO2 capture technology is then evaluated in terms of the potential cost for a mature system based on historic experience as technologies are improved with sequential iterations of the currently available system. The range costs for a supercritical power plant with solid sorbent-based CO2 capture was found to be 118 to 189 per megawatt hour with a nominal value of 163 per megawatt hour given the expected range of technological improvement in the capital and operating costs and efficiency of the power plant after 100 GW of cumulative worldwide experience. These results suggest that the solid sorbent-based system will not be competitive with currently available

  8. Thyristor Controlled Reactor for Power Factor Improvement

    Directory of Open Access Journals (Sweden)

    Sheila Mahapatra

    2014-04-01

    Full Text Available Power factor improvement is the essence of any power sector for reliable operation. This paper provides Thyristor Controlled Reactor regulated by programmed microcontroller which aids in improving power factor and retaining it close to unity under various loading conditions. The implementation is done on 8051 microcontrollerwhich isprogrammed using Keil software. To determine time lag between current and voltage PSpice softwareis used and to display power factor according tothe variation in loadProteus software is used. Whenever a capacitive load is connected to the transmission linea shunt reactor is connected which injects lagging reactive VARs to the power system. As a result the power factor is improved. The results given in this paper provides suitable microcontroller based reactive power compensation and power factor improvement technique using a Thyristor Controlled Reactor module.

  9. Multi-objective Extremum Seeking Control for Enhancement of Wind Turbine Power Capture with Load Reduction

    Science.gov (United States)

    Xiao, Yan; Li, Yaoyu; Rotea, Mario A.

    2016-09-01

    The primary objective in below rated wind speed (Region 2) is to maximize the turbine's energy capture. Due to uncertainty, variability of turbine characteristics and lack of inexpensive but precise wind measurements, model-free control strategies that do not use wind measurements such as Extremum Seeking Control (ESC) have received significant attention. Based on a dither-demodulation scheme, ESC can maximize the wind power capture in real time despite uncertainty, variabilities and lack of accurate wind measurements. The existing work on ESC based wind turbine control focuses on power capture only. In this paper, a multi-objective extremum seeking control strategy is proposed to achieve nearly optimum wind energy capture while decreasing structural fatigue loads. The performance index of the ESC combines the rotor power and penalty terms of the standard deviations of selected fatigue load variables. Simulation studies of the proposed multi-objective ESC demonstrate that the damage-equivalent loads of tower and/or blade loads can be reduced with slight compromise in energy capture.

  10. Mercury capture by native fly ash carbons in coal-fired power plants

    Science.gov (United States)

    Hower, James C.; Senior, Constance L.; Suuberg, Eric M.; Hurt, Robert H.; Wilcox, Jennifer L.; Olson, Edwin S.

    2013-01-01

    The control of mercury in the air emissions from coal-fired power plants is an on-going challenge. The native unburned carbons in fly ash can capture varying amounts of Hg depending upon the temperature and composition of the flue gas at the air pollution control device, with Hg capture increasing with a decrease in temperature; the amount of carbon in the fly ash, with Hg capture increasing with an increase in carbon; and the form of the carbon and the consequent surface area of the carbon, with Hg capture increasing with an increase in surface area. The latter is influenced by the rank of the feed coal, with carbons derived from the combustion of low-rank coals having a greater surface area than carbons from bituminous- and anthracite-rank coals. The chemistry of the feed coal and the resulting composition of the flue gas enhances Hg capture by fly ash carbons. This is particularly evident in the correlation of feed coal Cl content to Hg oxidation to HgCl2, enhancing Hg capture. Acid gases, including HCl and H2SO4 and the combination of HCl and NO2, in the flue gas can enhance the oxidation of Hg. In this presentation, we discuss the transport of Hg through the boiler and pollution control systems, the mechanisms of Hg oxidation, and the parameters controlling Hg capture by coal-derived fly ash carbons. PMID:24223466

  11. Integration of a high-pressure piperazine capture plant with a power plant: an energetic evaluation

    NARCIS (Netherlands)

    Ham, L.V. van der; Kler, R.C.F. de; Goetheer, E.L.V.

    2013-01-01

    Post-combustion CO2 capture can have a significant contribution to the reduction of CO2 emissions. However, it also requires a considerable amount of energy, causing a significant decrease in the net electricity output of the power plant it is associated with. A vast array of research initiatives is

  12. Effects of technological learning on future cost and performance of power plants with CO2 capture

    NARCIS (Netherlands)

    van den Broek, M.A.; Hoefnagels, E.T.A.; Rubin, E.; Turkenburg, W.C.; Faaij, A.P.C.

    2009-01-01

    This paper demonstrates the concept of applying learning curves in a consistent manner to performance as well as cost variables in order to assess the future development of power plants with CO2 capture. An existing model developed at Carnegie Mellon University, which had provided insight into the p

  13. Effects of technological learning on future cost and performance of power plants with CO2 capture

    NARCIS (Netherlands)

    van den Broek, M.A.; Hoefnagels, E.T.A.; Rubin, E.; Turkenburg, W.C.; Faaij, A.P.C.

    2009-01-01

    This paper demonstrates the concept of applying learning curves in a consistent manner to performance as well as cost variables in order to assess the future development of power plants with CO2 capture. An existing model developed at Carnegie Mellon University, which had provided insight into the

  14. Case Study On Power Factor Improvement

    Directory of Open Access Journals (Sweden)

    Samarjit Bhattacharyya

    2011-12-01

    Full Text Available Electrical Power constitutes a major component of the manufacturing cost in industry. In an electrical installation, power factor may become poor because of induction motors, welding machines, powertransformers, voltage regulators, arc and induction furnaces, choke coils, neon signs etc. A poor power factor for the plant causes huge amount of losses, leading to thermal problem in switchgears. However power factor is controllable with a properly designed power factor improvement capacitors system. The power factor correction obtained by using capacitor banks to generate locally the reactive energy necessary for the transfer of electrical useful power, allows a better and more rational technical-economical management of the plants. This paper describes different aspects of power factor improvement in a typical industrial plant with the help of a casestudy.

  15. Power Quality Improvement Using DVR

    Directory of Open Access Journals (Sweden)

    C. Benachaiba

    2009-01-01

    Full Text Available Voltage sags and swells in the medium and low voltage distribution grid are considered to be the most frequent type of power quality problems based on recent power quality studies. Their impact on sensitive loads is severe. The impact ranges from load disruptions to substantial economic losses up to millions of dollars. Different solutions have been developed to protect sensitive loads against such disturbances but the DVR is considered to be the most efficient and effective solution. Its appeal includes lower cost, smaller size and its dynamic response to the disturbance. This research described DVR principles and voltage restoration methods for balanced and/or unbalanced voltage sags and swells in a distribution system. Simulation results were presented to illustrate and understand the performances of DVR under voltage sags/swells conditions.

  16. Improved and safer nuclear power.

    Science.gov (United States)

    Taylor, J J

    1989-04-21

    Recent progress in advanced nuclear power development in the United States is revealing high potential for nuclear reactor systems that are smaller and easier to operate than the present generation. Passive, or intrinsic, characteristics are applied not only to provide inherent stability of the chain reaction but also to ensure continued cooling of the fuel and its containment systems even if a major breakdown of the normal cooling and control functions were to occur. The chance of a severe accident is thereby substantially reduced. The plant designs that are emerging are simpler and more rugged, have a longer life span, and place less burden on equipment and operating personnel. Modular design concepts and design standardization are also used to reduce construction time and engineering costs, giving promise that the cost of generating power from these systems will be competitive with alternative methods.

  17. CO2 capture processes in power plants - Le captage du CO2 dans les centrales thermiques

    OpenAIRE

    Bouallou, Chakib

    2010-01-01

    PDF file available for free at http://pubs.ub.ro/?pg=revues&rev=cscc6&num=201011&vol=1&aid=2975; International audience; This review is devoted to assess and compare various processes aiming at recover CO2 from power plants fed with natural gas (NGCC) and pulverized coal (PC). These processes are post combustion CO2 capture using chemical solvents, natural gas reforming for pre-combustion capture and oxy-fuel combustion with cryogenic recovery of CO2. These processes were evaluated to give so...

  18. Improving wind power quality with energy storage

    DEFF Research Database (Denmark)

    Rasmussen, Claus Nygaard

    2009-01-01

    The results of simulation of the influence of energy storage on wind power quality are presented. Simulations are done using a mathematical model of energy storage. Results show the relation between storage power and energy, and the obtained increase in minimum available power from the combination...... of wind and storage. The introduction of storage enables smoothening of wind power on a timescale proportional to the storage energy. Storage does not provide availability of wind power at all times, but allows for a certain fraction of average power in a given timeframe to be available with high...... probability. The amount of storage capacity necessary for significant wind power quality improvement in a given period is found to be 20 to 40% of the energy produced in that period. The necessary power is found to be 80 to 100% of the average power of the period....

  19. A Maximum Power Tracker for Improved Thermophotovoltaic Power Generation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Radioisotope Power Systems (RPS) are critical for future flagship exploration missions in space and on planetary surfaces. Small improvements in the RPS performance,...

  20. The National Carbon Capture Center at the Power Systems Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2014-12-30

    The National Carbon Capture Center (NCCC) at the Power Systems Development Facility supports the Department of Energy (DOE) goal of promoting the United States’ energy security through reliable, clean, and affordable energy produced from coal. Work at the NCCC supports the development of new power technologies and the continued operation of conventional power plants under CO2 emission constraints. The NCCC includes adaptable slipstreams that allow technology development of CO2 capture concepts using coal-derived syngas and flue gas in industrial settings. Because of the ability to operate under a wide range of flow rates and process conditions, research at the NCCC can effectively evaluate technologies at various levels of maturity and accelerate their development path to commercialization. During its first contract period, from October 1, 2008, through December 30, 2014, the NCCC designed, constructed, and began operation of the Post-Combustion Carbon Capture Center (PC4). Testing of CO2 capture technologies commenced in 2011, and through the end of the contract period, more than 25,000 hours of testing had been achieved, supporting a variety of technology developers. Technologies tested included advanced solvents, enzymes, membranes, sorbents, and associated systems. The NCCC continued operation of the existing gasification facilities, which have been in operation since 1996, to support the advancement of technologies for next-generation gasification processes and pre-combustion CO2 capture. The gasification process operated for 13 test runs, supporting over 30,000 hours combined of both gasification and pre-combustion technology developer testing. Throughout the contract period, the NCCC incorporated numerous modifications to the facilities to accommodate technology developers and increase test capabilities. Preparations for further testing were ongoing to continue advancement of the most promising technologies for

  1. Self-supporting power plant. Capturing evaporated water and save energy a new source of water

    Energy Technology Data Exchange (ETDEWEB)

    Daal, Ludwin; Vos, Frank de [KEMA Netherlands BV, Arnhem (Netherlands). Process and Cooling Water; KEMA Energy Consulting Co.Ltd, Beijing (China); Wageningen Univ. (Netherlands). Environmental Systems Analysis; Heijboer, Rob [KEMA Netherlands BV, Arnhem (Netherlands). Process and Cooling Water; Bekker, Bert [KEMA Energy Consulting Co.Ltd, Beijing (China); Gao, Xiu Xiu [Wageningen Univ. (Netherlands). Environmental Systems Analysis

    2013-07-01

    One of the major challenges of this century is the provision of water for a growing population and industry. The shortage in water resources in arid areas requires the availability of more efficient and cheaper water production processes. In some arid regions water is even more important than electricity. A large source of water is found in the form of evaporated water emitted from different industrial processes. If for example 20% of the evaporated water from the flue gas stream of a coal fired power plant would be captured, the plant would be self-supporting from a process water point of view. This is about 30m{sup 3} of water per hour. The results of the proof of principle project (2001-2008) show that >40% recovery can be achieved. Also an overall energy efficiency improvement can be achieved for industrial plants that reheat their flue gases. Calculations show that this can be about 1% overall efficiency for a coal fired power plant utilizing flue gas reheating. With an installed capacity of more than 600GWe in China, this energy saving results in a very large economic and fuel (coal) impact. This energy efficiency will most likely be the driving force to implement the technology in both water rich and water poor regions. For the capture of evaporated water no chemicals are used, there is no waste water formed and corrosion attack in stacks is mitigated. These results have led to the set up of a large international project named CapWa which aims to produce a membrane modular system suitable for industrial applications within 2-3years. The produced demin water from this system should be competitive with existing demin water technologies. The starting point will be the water vapour selective composite membranes that are developed in the proof of principle project. The CapWa project started in 2010 and consists of 14 partners of which 9 from the EU, 3 from the African continent and 2 from the Middle East.

  2. Particle capture in axial magnetic filters with power law flow model

    CERN Document Server

    Abbasov, T; Koksal, M

    1999-01-01

    A theory of capture of magnetic particle carried by laminar flow of viscous non-Newtonian (power law) fluid in axially ordered filters is presented. The velocity profile of the fluid flow is determined by the Kuwabara-Happel cell model. For the trajectory of the particle, the capture area and the filter performance simple analytical expressions are obtained. These expressions are valid for particle capture processes from both Newtonian and non-Newtonian fluids. For this reason the obtained theoretical results make it possible to widen the application of high-gradient magnetic filtration (HGMF) to other industrial areas. For Newtonian fluids the theoretical results are shown to be in good agreement with the experimental ones reported in the literature. (author)

  3. Particle capture in axial magnetic filters with power law flow model

    Science.gov (United States)

    Abbasov, T.; Herdem, S.; Köksal, M.

    1999-05-01

    A theory of capture of magnetic particle carried by laminar flow of viscous non-Newtonian (power law) fluid in axially ordered filters is presented. The velocity profile of the fluid flow is determined by the Kuwabara-Happel cell model. For the trajectory of the particle, the capture area and the filter performance simple analytical expressions are obtained. These expressions are valid for particle capture processes from both Newtonian and non-Newtonian fluids. For this reason the obtained theoretical results make it possible to widen the application of high-gradient magnetic filtration (HGMF) to other industrial areas. For Newtonian fluids the theoretical results are shown to be in good agreement with the experimental ones reported in the literature.

  4. Particle capture in axial magnetic filters with power law flow model

    Energy Technology Data Exchange (ETDEWEB)

    Abbasov, T.; Herdem, S.; Koksal, M. [Inonu University, Engineering Faculty, Department of Electrical and Electronics, Malatya (Turkey)

    1999-05-21

    A theory of capture of magnetic particle carried by laminar flow of viscous non-Newtonian (power law) fluid in axially ordered filters is presented. The velocity profile of the fluid flow is determined by the Kuwabara-Happel cell model. For the trajectory of the particle, the capture area and the filter performance simple analytical expressions are obtained. These expressions are valid for particle capture processes from both Newtonian and non-Newtonian fluids. For this reason the obtained theoretical results make it possible to widen the application of high-gradient magnetic filtration (HGMF) to other industrial areas. For Newtonian fluids the theoretical results are shown to be in good agreement with the experimental ones reported in the literature. (author)

  5. Improving Advanced Inverter Control Convergence in Distribution Power Flow

    Energy Technology Data Exchange (ETDEWEB)

    Nagarajan, Adarsh; Palmintier, Bryan; Ding, Fei; Mather, Barry; Baggu, Murali

    2016-11-21

    Simulation of modern distribution system powerflow increasingly requires capturing the impact of advanced PV inverter voltage regulation on powerflow. With Volt/var control, the inverter adjusts its reactive power flow as a function of the point of common coupling (PCC) voltage. Similarly, Volt/watt control curtails active power production as a function of PCC voltage. However, with larger systems and higher penetrations of PV, this active/reactive power flow itself can cause significant changes to the PCC voltage potentially introducing oscillations that slow the convergence of system simulations. Improper treatment of these advanced inverter functions could potentially lead to incorrect results. This paper explores a simple approach to speed such convergence by blending in the previous iteration's reactive power estimate to dampen these oscillations. Results with a single large (5MW) PV system and with multiple 500kW advanced inverters show dramatic improvements using this approach.

  6. AMERICAN ELECTRIC POWER'S CONESVILLE POWER PLANT UNIT NO.5 CO2 CAPTURE RETROFIT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Carl R. Bozzuto; Nsakala ya Nsakala; Gregory N. Liljedahl; Mark Palkes; John L. Marion

    2001-06-30

    ALSTOM Power Inc.'s Power Plant Laboratories (ALSTOM) has teamed with American Electric Power (AEP), ABB Lummus Global Inc. (ABB), the US Department of Energy National Energy Technology Laboratory (DOE NETL), and the Ohio Coal Development Office (OCDO) to conduct a comprehensive study evaluating the technical feasibility and economics of alternate CO{sub 2} capture and sequestration technologies applied to an existing US coal-fired electric generation power plant. The motivation for this study was to provide input to potential US electric utility actions concerning GHG emissions reduction. If the US decides to reduce CO{sub 2} emissions, action would need to be taken to address existing power plants. Although fuel switching from coal to natural gas may be one scenario, it will not necessarily be a sufficient measure and some form of CO{sub 2} capture for use or disposal may also be required. The output of this CO{sub 2} capture study will enhance the public's understanding of control options and influence decisions and actions by government, regulators, and power plant owners in considering the costs of reducing greenhouse gas CO{sub 2} emissions. The total work breakdown structure is encompassed within three major reports, namely: (1) Literature Survey, (2) AEP's Conesville Unit No.5 Retrofit Study, and (3) Bench-Scale Testing and CFD Evaluation. The report on the literature survey results was issued earlier by Bozzuto, et al. (2000). Reports entitled ''AEP's Conesville Unit No.5 Retrofit Study'' and ''Bench-Scale Testing and CFD Evaluation'' are provided as companion volumes, denoted Volumes I and II, respectively, of the final report. The work performed, results obtained, and conclusions and recommendations derived therefrom are summarized.

  7. CO2 capture from power plants: Part I. A parametric study of the technical performance based on monoethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, Mohammad R.M.; Schneiders, Le´on H.J.; Niederer, John P.M.; Feron, Paul H.M.; Versteeg, Geert F.

    2007-01-01

    Capture and storage of CO2 from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO2 capture process from flue gas of a 600 MWe bituminous coal fired power plant, based

  8. CO2 capture from power plants: Part I. A parametric study of the technical performance based on monoethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, Mohammad R.M.; Schneiders, Léon H.J.; Niederer, John; Feron, Paul H.M.; Versteeg, Geert

    2007-01-01

    Capture and storage of CO2 from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO2 capture process from flue gas of a 600 MWe bituminous coal fired power plant, based

  9. CO2 capture from power plants. Part I : A parametric study of the technical performance based on monoethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, M. R. M.; Schneiders, L. H. J.; Niederer, J. P. M.; Feron, P. H. M.; Versteeg, G. F.

    Capture and storage of CO2 from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO2 capture process from flue gas of a 600 MWe bituminous coal fired power plant, based

  10. CO2 capture from power plants. Part I : A parametric study of the technical performance based on monoethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, M. R. M.; Schneiders, L. H. J.; Niederer, J. P. M.; Feron, P. H. M.; Versteeg, G. F.

    2007-01-01

    Capture and storage of CO2 from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO2 capture process from flue gas of a 600 MWe bituminous coal fired power plant, based

  11. THE NATIONAL CARBON CAPTURE CENTER AT THE POWER SYSTEMS DEVELOPMENT FACILITY

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2011-05-11

    The Power Systems Development Facility (PSDF) is a state-of-the-art test center sponsored by the U.S. Department of Energy and dedicated to the advancement of clean coal technology. In addition to the development of advanced coal gasification processes, the PSDF features the National Carbon Capture Center (NCCC) to study CO2 capture from coal-derived syngas and flue gas. The NCCC includes multiple, adaptable test skids that allow technology development of CO2 capture concepts using coal-derived syngas and flue gas in industrial settings. Because of the ability to operate under a wide range of flow rates and process conditions, research at the NCCC can effectively evaluate technologies at various levels of maturity. During the Budget Period Two reporting period, efforts at the PSDF/NCCC focused on new technology assessment and test planning; designing and constructing post-combustion CO2 capture facilities; testing of pre-combustion CO2 capture and related processes; and operating the gasification process to develop gasification related technologies and for syngas generation to test syngas conditioning technologies.

  12. The national carbon capture center at the power systems development facility

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2012-09-01

    The Power Systems Development Facility (PSDF) is a state-of-the-art test center sponsored by the U.S. Department of Energy and dedicated to the advancement of clean coal technology. In addition to the development of advanced coal gasification processes, the PSDF features the National Carbon Capture Center (NCCC) to study CO2 capture from coal-derived syngas and flue gas. The NCCC includes multiple, adaptable test skids that allow technology development of CO2 capture concepts using coal-derived syngas and flue gas in industrial settings. Because of the ability to operate under a wide range of flow rates and process conditions, research at the NCCC can effectively evaluate technologies at various levels of maturity. During the Budget Period Three reporting period, efforts at the NCCC/PSDF focused on testing of pre-combustion CO2 capture and related processes; commissioning and initial testing at the post-combustion CO2 capture facilities; and operating the gasification process to develop gasification related technologies and for syngas generation to test syngas conditioning technologies.

  13. Analysis of thermally coupled chemical looping combustion-based power plants with carbon capture

    KAUST Repository

    Iloeje, Chukwunwike

    2015-04-01

    © 2015 Elsevier Ltd. A number of CO2 capture-enabled power generation technologies have been proposed to address the negative environmental impact of CO2 emission. One important barrier to adopting these technologies is the associated energy penalty. Chemical-looping Combustion (CLC) is an oxy-combustion technology that can significantly lower this penalty. It utilizes an oxygen carrier to transfer oxygen from air/oxidizing stream in an oxidation reactor to the fuel in a reduction reactor. Conventional CLC reactor designs employ two separate reactors, with metal/metal oxide particles circulating pneumatically in-between. One of the key limitations of these designs is the entropy generation due to reactor temperature difference, which lowers the cycle efficiency. Zhao et al. (Zhao et al., 2014; Zhao and Ghoniem, 2014) proposed a new CLC rotary reactor design, which overcomes this limitation. This reactor consists of a single rotating wheel with micro-channels designed to maintain thermal equilibrium between the fuel and air sides. This study uses three thermodynamic models of increasing fidelity to demonstrate that the internal thermal coupling in the rotary CLC reactor creates the potential for improved cycle efficiency. A theoretical availability model and an ideal thermodynamic cycle model are used to define the efficiency limits of CLC systems, illustrate the impact of reactor thermal coupling and discuss relevant criteria. An Aspen Plus® model of a regenerative CLC cycle is then used to show that this thermal coupling raises the cycle efficiency by up to 2% points. A parametric study shows that efficiency varies inversely with pressure, with a maximum of 51% at 3bar, 1000C and 60% at 4bar, 1400C. The efficiency increases with CO2 fraction at high pressure ratios but exhibits a slight inverse dependence at low pressure ratios. The parametric study shows that for low purge steam demand, steam generation improves exhaust heat recovery and increases efficiency

  14. Comparing post-combustion CO2 capture operation at retrofitted coal-fired power plants in the Texas and Great Britain electric grids

    Science.gov (United States)

    Cohen, Stuart M.; Chalmers, Hannah L.; Webber, Michael E.; King, Carey W.

    2011-04-01

    This work analyses the carbon dioxide (CO2) capture system operation within the Electric Reliability Council of Texas (ERCOT) and Great Britain (GB) electric grids using a previously developed first-order hourly electricity dispatch and pricing model. The grids are compared in their 2006 configuration with the addition of coal-based CO2 capture retrofits and emissions penalties from 0 to 100 US dollars per metric ton of CO2 (USD/tCO2). CO2 capture flexibility is investigated by comparing inflexible CO2 capture systems to flexible ones that can choose between full- and zero-load CO2 capture depending on which operating mode has lower costs or higher profits. Comparing these two grids is interesting because they have similar installed capacity and peak demand, and both are isolated electricity systems with competitive wholesale electricity markets. However, differences in capacity mix, demand patterns, and fuel markets produce diverging behaviours of CO2 capture at coal-fired power plants. Coal-fired facilities are primarily base load in ERCOT for a large range of CO2 prices but are comparably later in the dispatch order in GB and consequently often supply intermediate load. As a result, the ability to capture CO2 is more important for ensuring dispatch of coal-fired facilities in GB than in ERCOT when CO2 prices are high. In GB, higher overall coal prices mean that CO2 prices must be slightly higher than in ERCOT before the emissions savings of CO2 capture offset capture energy costs. However, once CO2 capture is economical, operating CO2 capture on half the coal fleet in each grid achieves greater emissions reductions in GB because the total coal-based capacity is 6 GW greater than in ERCOT. The market characteristics studied suggest greater opportunity for flexible CO2 capture to improve operating profits in ERCOT, but profit improvements can be offset by a flexibility cost penalty.

  15. Tuning anion-functionalized ionic liquids for improved SO2 capture.

    Science.gov (United States)

    Cui, Guokai; Zheng, Junjie; Luo, Xiaoyan; Lin, Wenjun; Ding, Fang; Li, Haoran; Wang, Congmin

    2013-09-27

    You can have your cake and eat it too: A "dual-tuning" strategy for improving the capture of SO2 was developed by introducing electron-withdrawing sites on the anions to produce several kinds of functionalized ionic liquids. Those functionalized with a halogen group exhibited improved performance over their non-halogenated counterparts, leading to highly efficient and reversible capture. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Power Burst Facility/Boron Neutron Capture Therapy Program for cancer treatment

    Energy Technology Data Exchange (ETDEWEB)

    Ackermann, A.L. (ed.); Dorn, R.V. III.

    1990-08-01

    This report discusses monthly progress in the Power Boron Facility/Boron Neutron Capture Therapy (PBF/BNCT) Program for Cancer Treatment. Highlights of the PBF/BNCT Program during August 1990 include progress within the areas of: Gross Boron Analysis in Tissue, Blood, and Urine, boron microscopic (subcellular) analytical development, noninvasive boron quantitative determination, analytical radiation transport and interaction modeling for BNCT, large animal model studies, neutron source and facility preparation, administration and common support and PBF operations.

  17. Power Burst Facility/Boron Neutron Capture Therapy Program for cancer treatment

    Energy Technology Data Exchange (ETDEWEB)

    Ackermann, A.L. (ed.); Dorn, R.V. III.

    1990-08-01

    This report discusses monthly progress in the Power Boron Facility/Boron Neutron Capture Therapy (PBF/BNCT) Program for Cancer Treatment. Highlights of the PBF/BNCT Program during August 1990 include progress within the areas of: Gross Boron Analysis in Tissue, Blood, and Urine, boron microscopic (subcellular) analytical development, noninvasive boron quantitative determination, analytical radiation transport and interaction modeling for BNCT, large animal model studies, neutron source and facility preparation, administration and common support and PBF operations.

  18. CO2 capture and storage in Greece: A case study from komotini ngcc power plant

    Directory of Open Access Journals (Sweden)

    Koukouzas Nikolaos

    2006-01-01

    Full Text Available The aim of this paper is to examine the possibilities for the abatement of CO2 emissions in the Greek fossil fuel power generation sector. An overview of CO2 capture, transportation, and storage concepts, on which the R&D community is focused, is presented. The implementation of post-combustion CO2 capture options in an existing fossil fuel power plant is then examined and the consequences on the overall plant performance are determined. Finally, the possibilities of transportation and then underground storage of the pure CO2 stream are analyzed taking into account both technical and economical factors. The results of this analysis show that CO2 sequestration is technically feasible for existing fossil fuel fired power plants in Greece. However, substantial reduction in plant efficiency is observed due to increased energy demand of the technologies used as well as in electricity production cost due to capital and operation costs of capture, transport, and storage of CO2. .

  19. Pre-capture multiplexing improves efficiency and cost-effectiveness of targeted genomic enrichment

    Directory of Open Access Journals (Sweden)

    Shearer A Eliot

    2012-11-01

    Full Text Available Abstract Background Targeted genomic enrichment (TGE is a widely used method for isolating and enriching specific genomic regions prior to massively parallel sequencing. To make effective use of sequencer output, barcoding and sample pooling (multiplexing after TGE and prior to sequencing (post-capture multiplexing has become routine. While previous reports have indicated that multiplexing prior to capture (pre-capture multiplexing is feasible, no thorough examination of the effect of this method has been completed on a large number of samples. Here we compare standard post-capture TGE to two levels of pre-capture multiplexing: 12 or 16 samples per pool. We evaluated these methods using standard TGE metrics and determined the ability to identify several classes of genetic mutations in three sets of 96 samples, including 48 controls. Our overall goal was to maximize cost reduction and minimize experimental time while maintaining a high percentage of reads on target and a high depth of coverage at thresholds required for variant detection. Results We adapted the standard post-capture TGE method for pre-capture TGE with several protocol modifications, including redesign of blocking oligonucleotides and optimization of enzymatic and amplification steps. Pre-capture multiplexing reduced costs for TGE by at least 38% and significantly reduced hands-on time during the TGE protocol. We found that pre-capture multiplexing reduced capture efficiency by 23 or 31% for pre-capture pools of 12 and 16, respectively. However efficiency losses at this step can be compensated by reducing the number of simultaneously sequenced samples. Pre-capture multiplexing and post-capture TGE performed similarly with respect to variant detection of positive control mutations. In addition, we detected no instances of sample switching due to aberrant barcode identification. Conclusions Pre-capture multiplexing improves efficiency of TGE experiments with respect to hands-on time

  20. Power Quality Improvement of a Distributed Generation Power System

    Directory of Open Access Journals (Sweden)

    Panga Harish

    2016-06-01

    Full Text Available The aim of this work is to improve the power quality for Distributed Generation (DG with power storage system. Power quality is the combination of voltage quality and current quality. Power quality is the set of limits of electrical properties that allows electrical systems to function in their intended manner without significant loss of performance or life. The electrical power quality is more concerned issue. The main problems are stationery and transient distortions in the line voltage such as harmonics, flicker, swells, sags and voltage asymmetries. Distributed Generation (DG also called as site generation, dispersed generation, embedded generation, decentralized generation, decentralized energy or distributed energy, generates electricity from the many small energy sources. In recent years, micro electric power systems such as photovoltaic generation systems, wind generators and micro gas turbines, etc., have increased with the deregulation and liberalization of the power market. Under such circumstances the environment surrounding the electric power industry has become ever more complicated and provides high-quality power in a stable manner which becomes an important topic. Here DG is assumed to include Wind power Generation (WG and Fuel Cells (FC, etc. Advantages of this system are constant power supply, constant voltage magnitude, absence of harmonics insupply voltage, un-interrupted power supply. In this project the electric power qualities in two cases will be compared. Case I: With the storage battery when it is introduced. Case II: Without the storage battery. The storage battery executes the control that maintains the voltage in the power system. It will be found that the Electric power quality will be improved, when storage battery is introduced. The model system used in this Project work is composed of a Wind Turbine, an Induction Generator, Fuel Cells, An Inverter and a Storage Battery. A miniature Wind Power Generator is

  1. Capturing User Needs to Improve Processes at EOSDIS Data Centers

    Science.gov (United States)

    Sofinowski, E. J.; Boquist, C. L.

    2009-12-01

    Since 2004 the Earth Observing System Data and Information System (EOSDIS) has conducted an annual comprehensive survey of user satisfaction using the American Customer Satisfaction Index (ACSI). Customer satisfaction ratings for EOSDIS consistently rate better than the overall government ratings. As part of the survey users are asked to submit comments concerning their experiences and interests. These user comments provide valuable insight into the effect of data center processes on users' experiences. Although user satisfaction has remained high, their preferences have changed with the rapid advances in web-based services. This analysis investigates the correlation between user comments, process changes or capability improvements at the individual data centers, and whether the changes at the data centers and web sites show a corresponding increase in user satisfaction. We will evaluate the comments in the areas of Product Search, Product Selection and Order, Delivery, Product Quality and Customer Support.

  2. The National Carbon Capture Center at the Power Systems Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2014-07-14

    The Power Systems Development Facility (PSDF) is a state-of-the-art test center sponsored by the U.S. Department of Energy (DOE) and dedicated to the advancement of clean coal technology. In addition to the development of high efficiency coal gasification processes, the PSDF features the National Carbon Capture Center (NCCC) to promote new technologies for CO2 capture from coal-derived flue gas and syngas. The NCCC includes multiple, adaptable test skids that allow technology development of CO2 capture concepts using coal-derived flue gas and syngas in industrial settings. Because of the ability to operate under a wide range of flow rates and process conditions, research at the NCCC can effectively evaluate technologies at various levels of maturity and accelerate their development paths to commercialization. During the calendar year 2013 portion of the Budget Period Four reporting period, efforts at the NCCC focused on post-combustion CO2 capture, gasification, and pre-combustion CO2 capture technology testing. Preparations for future testing were on-going as well, and involved facility upgrades and collaboration with numerous technology developers. In the area of post-combustion, testing was conducted on an enzyme-based technology, advanced solvents from two major developers, and a gas separation membrane. During the year, the gasification process was operated for three test runs, supporting development of water-gas shift and COS hydrolysis catalysts, a mercury sorbent, and several gasification support technologies. Syngas produced during gasification operation was also used for pre-combustion capture technologies, including gas separation membranes from three different technology developers, a CO2 sorbent, and CO2 solvents.

  3. Low Cost, High Capacity Regenerable Sorbent for Carbon Dioxide Capture from Existing Coal-fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Alptekin, Gokhan [TDA Research, Inc., Wheat Ridge, CO (United States); Jayaraman, Ambalavanan [TDA Research, Inc., Wheat Ridge, CO (United States); Dietz, Steven [TDA Research, Inc., Wheat Ridge, CO (United States)

    2016-03-03

    .90 and $39.71 per tonne compared to $65.46 and $66.56 per tonne for amine based system on 2011 $ basis, providing 40% lower cost of CO2 captured. In this analysis we have used a sorbent life of 4 years. If a longer sorbent life can be maintained (which is not unreasonable for fixed bed commercial PSA systems), this would lower the cost of CO2 captured by $0.05 per tonne (e.g., to $38.85 and $39.66 per tonne at 5 years sorbent replacement). These system analysis results suggest that TDA’s VSA-based post-combustion capture technology can substantially improve the power plant’s thermal performance while achieving near zero emissions, including greater than 90% carbon capture. The higher net plant efficiency and lower capital and operating costs results in a substantial reduction in the cost of carbon capture and cost of electricity for the power plant equipped with TDA’s technology.

  4. The National Carbon Capture Center at the Power Systems Development Facility: Topical Report

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2011-03-01

    The Power Systems Development Facility (PSDF) is a state-of-the-art test center sponsored by the U.S. Department of Energy and dedicated to the advancement of clean coal technology. In addition to the development of advanced coal gasification processes, the PSDF features the National Carbon Capture Center (NCCC) to study CO2 capture from coal-derived syngas and flue gas. The newly established NCCC will include multiple, adaptable test skids that will allow technology development of CO2 capture concepts using coal-derived syngas and flue gas in industrial settings. Because of the ability to operate under a wide range of flow rates and process conditions, research at the NCCC can effectively evaluate technologies at various levels of maturity. During the Budget Period One reporting period, efforts at the PSDF/NCCC focused on developing a screening process for testing consideration of new technologies; designing and constructing pre- and post-combustion CO2 capture facilities; developing sampling and analytical methods; expanding fuel flexibility of the Transport Gasification process; and operating the gasification process for technology research and for syngas generation to test syngas conditioning technologies.

  5. Improved Neutron Capture Cross Section Measurements with the n_TOF Total Absorption Calorimeter

    CERN Document Server

    Mendoza, E; Perkowski, J; Andriamonje, S; Carrapico, C; Moinul, M; Vannini, G; Quesada, J M; Harrisopulos, S; Milazzo, P M; Berthier, B; Lozano, M; Krticka, M; Domingo-Pardo, C; Nolte, R; Chiaveri, E; Saarmento, H; Jericha, E; Ferrari, A; Massimi, C; Giubrone, G; Avrigeanu, V; Martinez, T; Guerrero, C; Andrzejewski, J; Karadimos, D; Mengoni, A; Ganesan, S; Vlachoudis, V; Becares, V; Cortes, G; Variale, V; Losito, H; Calvino, F; Kappeler, F; Gunsing, F; Gramegna, F; Colonna, N; Marrone, S; Pavlik, A; Berthoumieux, E; Paradela, C; Mastinu, P F; Vaz, P; Tassan-Got, L; Kadi, Y; Tarrio, D; Cano-Ott, D; Brugger, M; Wallner, A; Audouin, L; Fernandez-Ordonez, M; Becvar, F; Goncalves, I F; Cerutti, F; Ventura, A; Mosconi, M; Tagliente, G; Duran, I; Casado, A; Ioannides, K; Weiss, C; Mirea, M; Gomez-Hornillos, M B; Vlastou, R; Calviani, M; Lederer, C; Gonzalez-Romero, E; Marganiec, J; Vidriales, J J; Lebbos, E; Leeb, H; Heil, M; Dillmann, I; Tain, J L; Belloni, F

    2011-01-01

    The n\\_TOF collaboration operates a Total Absorption Calorimeter (TAC) {[}1] for measuring neutron capture cross-sections of low-mass and/or radioactive samples. The results obtained with the TAC have led to a substantial improvement of the capture cross sections of (237)Np and (240)Pu {[}2]. The experience acquired during the first measurements has allowed us to optimize the performance of the TAC and to improve the capture signal to background ratio, thus opening the way to more complex and demanding measurements on rare radioactive materials. The new design has been reached by a series of detailed Monte Carlo simulations of complete experiments and dedicated test measurements. The new capture setup will be presented and the main achievements highlighted.

  6. Oxy-fuel combustion for power generation and carbon dioxide (CO2) capture

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Ligang (ed.) [Canmet, Natural Resources Canada, Ottawa, Ontario (Canada)], email: lzheng@nrcan-rncan.gc.ca

    2011-07-01

    An important part of the world's electricity is produced from coal. It is a predominant resource for power generation because of its abundance and world-wide distribution. However the use of coal results in emissions of carbon monoxide, oxides of sulphur and nitrogen (NOx) and particle matter which have a negative impact on the environment. In order to reduce CO2 emissions, the plant's efficiency can be increased or the carbon can be captured, liquefied, and transported to an underground storage site through the carbon capture and storage (CCS) process. Three options can be used for CCS; oxy-fuel combustion is the most promising as it does not require CO2 separation. This book presents the oxy-fuel combustion technology, its current state, development needs and prospective timeline. The book's 15 chapters were all analyzed separately for inclusion in this database.

  7. Steady-state simulation and optimization of an integrated gasification combined cycle power plant with CO2 capture

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharyya, D.; Turton, R.; Zitney, S.

    2011-01-01

    useful and effective in a process simulator environment for improving efficiency and flexibility of IGCC power plants with CO2 capture. In addition, the study identifies a number of key design variables that has strong impact on the efficiency of an IGCC plant with CO2 capture.

  8. CO2 capture using fly ash from coal fired power plant and applications of CO2-captured fly ash as a mineral admixture for concrete.

    Science.gov (United States)

    Siriruang, Chaichan; Toochinda, Pisanu; Julnipitawong, Parnthep; Tangtermsirikul, Somnuk

    2016-04-01

    The utilization of fly ash as a solid sorbent material for CO2 capture via surface adsorption and carbonation reaction was evaluated as an economically feasible CO2 reduction technique. The results show that fly ash from a coal fired power plant can capture CO2 up to 304.7 μmol/g fly ash, consisting of 2.9 and 301.8 μmol/g fly ash via adsorption and carbonation, respectively. The CO2 adsorption conditions (temperature, pressure, and moisture) can affect CO2 capture performance of fly ash. The carbonation of CO2 with free CaO in fly ashes was evaluated and the results indicated that the reaction consumed most of free CaO in fly ash. The fly ashes after CO2 capture were further used for application as a mineral admixture for concrete. Properties such as water requirement, compressive strength, autoclave expansion, and carbonation depth of mortar and paste specimens using fly ash before and after CO2 capture were tested and compared with material standards. The results show that the expansion of mortar specimens using fly ash after CO2 capture was greatly reduced due to the reduction of free CaO content in the fly ash compared to the expansion of specimens using fresh fly ash. There were no significant differences in the water requirement and compressive strength of specimens using fly ash, before and after CO2 capture process. The results from this study can lead to an alternative CO2 capture technique with doubtless utilization of fly ash after CO2 capture as a mineral admixture for concrete.

  9. Capturing power at higher voltages from arrays of microbial fuel cells without voltage reversal

    KAUST Repository

    Kim, Younggy

    2011-01-01

    Voltages produced by microbial fuel cells (MFCs) cannot be sustainably increased by linking them in series due to voltage reversal, which substantially reduces stack voltages. It was shown here that MFC voltages can be increased with continuous power production using an electronic circuit containing two sets of multiple capacitors that were alternately charged and discharged (every one second). Capacitors were charged in parallel by the MFCs, but linked in series while discharging to the circuit load (resistor). The parallel charging of the capacitors avoided voltage reversal, while discharging the capacitors in series produced up to 2.5 V with four capacitors. There were negligible energy losses in the circuit compared to 20-40% losses typically obtained with MFCs using DC-DC converters to increase voltage. Coulombic efficiencies were 67% when power was generated via four capacitors, compared to only 38% when individual MFCs were operated with a fixed resistance of 250 Ω. The maximum power produced using the capacitors was not adversely affected by variable performance of the MFCs, showing that power generation can be maintained even if individual MFCs perform differently. Longer capacitor charging and discharging cycles of up to 4 min maintained the average power but increased peak power by up to 2.6 times. These results show that capacitors can be used to easily obtain higher voltages from MFCs, allowing for more useful capture of energy from arrays of MFCs. © 2011 The Royal Society of Chemistry.

  10. Load Mitigation and Optimal Power Capture for Variable Speed Wind Turbine in Region 2

    Directory of Open Access Journals (Sweden)

    Saravanakumar Rajendran

    2015-01-01

    Full Text Available This paper proposes the two nonlinear controllers for variable speed wind turbine (VSWT operating at below rated wind speed. The objective of the controller is to maximize the energy capture from the wind with reduced oscillation on the drive train. The conventional controllers such as aerodynamic torque feedforward (ATF and indirect speed control (ISC are adapted initially, which introduce more power loss, and the dynamic aspects of WT are not considered. In order to overcome the above drawbacks, modified nonlinear static state with feedback estimator (MNSSFE and terminal sliding mode controller (TSMC based on Modified Newton Raphson (MNR wind speed estimator are proposed. The proposed controllers are simulated with nonlinear FAST (fatigue, aerodynamics, structures, and turbulence WT dynamic simulation for different mean wind speeds at below rated wind speed. The frequency analysis of the drive train torque is done by taking the power spectral density (PSD of low speed shaft torque. From the result, it is found that a trade-off is to be maintained between the transient load on the drive train and maximum power capture.

  11. Power plant productivity improvement in New York

    Energy Technology Data Exchange (ETDEWEB)

    None

    1981-03-01

    The New York Public Service Commission (PSC), under contract with the US Department of Energy (DOE), began a joint program in September 1978 to improve the productivity of coal and nuclear electric generating units in New York State. The project had dual objectives: to ensure that the utilities in New York State have or develop a systematic permanent, cost-effective productivity improvement program based on sound engineering and economic considerations, and to develop a model program for Power Plant Productivity Improvement, which, through DOE, can also be utilized by other regulatory commissions in the country. To accomplish these objectives, the program was organized into the following sequence of activities: compilation and analysis of power plant performance data; evaluation and comparison of utility responses to outage/derating events; power plant productivity improvement project cost-benefit analysis; and evaluation of regulatory procedures and policies for improving productivity. The program that developed for improving the productivity of coal units is substantially different than for nuclear units. Each program is presented, and recommendations are made for activities of both the utilities and regulatory agencies which will promote improved productivity.

  12. Post combustion CO2 capture as energy penalty in real power plant by retrofiting exergy efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Parvandad Asadollahi, Maryam [Department of Mechanics, University of Manchester (United Kingdom)], e-mail: maryamassadollahi@yahoo.com

    2011-07-01

    Carbon dioxide (CO2) capture and storage is the only way the world to continue to enjoy the benefits of using coal while drastically reducing the emissions associated with coal combustion. CO2 is a component of the flue gas in a coal-fired power plant. The total pressure of the flue gas is 1 atm and the CO2 concentration is typically 10-15%. The process of transforming this low pressure, low concentration CO2 into a relatively pure CO2 stream is referred to as post-combustion capture. Present-day post-combustion capture plants currently use chemical absorption processes. Three systems based on amine-, carbonate- and ammonia-based process are discussed and presented in this paper. Use of other solvents with lower binding energy is suggested to decrease the exergy loss at the reboiler section. By adding flash for desalinating saline water, exergy loss is reduced significantly and extraction of steam at various pressures is possible through the heat recovery steam generator.

  13. The National Carbon Capture Center at the Power Systems Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-12-31

    The Power Systems Development Facility (PSDF) is a state-of-the-art test center sponsored by the U.S. Department of Energy and dedicated to the advancement of clean coal technology. In addition to the development of high efficiency coal gasification processes, the PSDF features the National Carbon Capture Center (NCCC) to promote new technologies for CO{sub 2} capture from coal-derived syngas and flue gas. The NCCC includes multiple, adaptable test skids that allow technology development of CO{sub 2} capture concepts using coal-derived syngas and flue gas in industrial settings. Because of the ability to operate under a wide range of flow rates and process conditions, research at the NCCC can effectively evaluate technologies at various levels of maturity and accelerate their development path to commercialization. During the calendar year 2012 portion of the Budget Period Four reporting period, efforts at the NCCC focused on testing of pre- and post-combustion CO{sub 2} capture processes and gasification support technologies. Preparations for future testing were on-going as well, and involved facility upgrades and collaboration with numerous technology developers. In the area of pre-combustion, testing was conducted on a new water-gas shift catalyst, a CO{sub 2} solvent, and gas separation membranes from four different technology developers, including two membrane systems incorporating major scale-ups. Post-combustion tests involved advanced solvents from three major developers, a gas separation membrane, and two different enzyme technologies. An advanced sensor for gasification operation was evaluated, operation with biomass co-feeding with coal under oxygen-blown conditions was achieved, and progress continued on refining several gasification support technologies.

  14. The National Carbon Capture Center at the Power Systems Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2012-12-31

    The Power Systems Development Facility (PSDF) is a state-of-the-art test center sponsored by the U.S. Department of Energy and dedicated to the advancement of clean coal technology. In addition to the development of high efficiency coal gasification processes, the PSDF features the National Carbon Capture Center (NCCC) to promote new technologies for CO2 capture from coal-derived syngas and flue gas. The NCCC includes multiple, adaptable test skids that allow technology development of CO2 capture concepts using coal-derived syngas and flue gas in industrial settings. Because of the ability to operate under a wide range of flow rates and process conditions, research at the NCCC can effectively evaluate technologies at various levels of maturity and accelerate their development path to commercialization. During the calendar year 2012 portion of the Budget Period Four reporting period, efforts at the NCCC focused on testing of pre- and post-combustion CO2 capture processes and gasification support technologies. Preparations for future testing were on-going as well, and involved facility upgrades and collaboration with numerous technology developers. In the area of pre-combustion, testing was conducted on a new water-gas shift catalyst, a CO2 solvent, and gas separation membranes from four different technology developers, including two membrane systems incorporating major scale-ups. Post-combustion tests involved advanced solvents from three major developers, a gas separation membrane, and two different enzyme technologies. An advanced sensor for gasification operation was evaluated, operation with biomass co-feeding with coal under oxygen-blown conditions was achieved, and progress continued on refining several gasification support technologies.

  15. Optimal control system design for IGCC power plants with CO2 capture

    Energy Technology Data Exchange (ETDEWEB)

    Jones, D.; Bhattacharyya, D.; Turton, R.; Zitney, S.

    2012-01-01

    Designing an optimal control system for an integrated gasification combined cycle (IGCC) power plant with CO2 capture addresses the challenge of efficiently operating and controlling a coal-fed IGCC plant with the desired extent of CO2 capture in the face of disturbances without violating operational and environmental constraints. The control system design needs to optimize a desired scalar objective function while satisfying all the operational and environmental constraints in the presence of measured and unmeasured disturbances. Various objective functions can be considered for the control system design such as maximization of profit, maximization of the power produced, or minimization of the auxiliary power. The design of such a control system makes the plant suitable to play an active role in the smart grid era as the plant will have the required agility. In addition, other penalty function(s) such as emission penalties for CO2 or other criteria pollutants can be considered in the framework as well as losses associated with any hydrogen or carbon monoxide loses. The proposed control system design is performed in two stages. In the first stage, a top-down analysis is performed to generate a list of controlled, manipulated, and disturbance variables considering a scalar operational objective and other process constraints. In the second stage, a bottom-up approach for simultaneous design of the control structure and the controllers is used. In this paper, the first stage of the two-stage approach is applied to the IGCC’s acid gas removal (AGR) process which removes both H2S and CO2 from the shifted synthesis gas. While these results are still preliminary, they demonstrate the application of the proposed approach for a commercial-scale plant and show some interesting results related to controlled variable selection. Such an approach can be followed not only to design control systems for new power plants, but also to retrofit control systems for existing plants

  16. Progress Towards Commercialization of Electrochemical Membrane Technology for CO2 Capture and Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Ghezel-Ayagh, Hossein; Jolly, Stephen; DiNitto, M.; Hunt, Jennifer; Patel, Dilip; Steen, William A.; Richardson, C. F.; Marina, Olga A.; Pederson, Larry R.

    2014-03-01

    To address the concerns about climate change resulting from emission of CO2 by coal-fueled power plants, FuelCell Energy, Inc. has developed Combined Electric Power and Carbon-dioxide Separation (CEPACS) system concept, as a novel solution for greenhouse gas emission reduction. The CEPACS system utilizes Electrochemical Membrane (ECM) technology derived from the Company’s well established Direct FuelCell® products. The system concept works as two devices in one: it separates the CO2 from the exhaust of other plants and simultaneously, using a supplementary fuel, produces electric power at high efficiency. FCE is currently evaluating the use of ECM to cost effectively separate CO2 from the flue gas of coal fired power plants under a U.S. Department of Energy contract. The overarching objective of the project is to verify that the ECM can achieve at least 90% CO2 capture from flue gas of a PC plant with no more than 35% increase in the cost of electricity. The specific objectives and related activities presently ongoing for the project include: 1) conduct bench scale tests of ECM and 2) evaluate the effects of impurities present in the coal plant flue gas by laboratory scale performance tests of the membrane.

  17. Efficiency improvement of thermal coal power plants

    Energy Technology Data Exchange (ETDEWEB)

    Hourfar, D. [VEBA Kraftwerke Ruhr Ag, Gelsenkirchen (Germany)

    1996-12-31

    The discussion concerning an increase of the natural greenhouse effect by anthropogenic changes in the composition of the atmosphere has increased over the past years. The greenhouse effect has become an issue of worldwide debate. Carbon dioxide is the most serious emission of the greenhouse gases. Fossil-fired power plants have in the recent past been responsible for almost 30 % of the total CO{sub 2} emissions in Germany. Against this background the paper will describe the present development of CO{sub 2} emissions from power stations and present actual and future opportunities for CO{sub 2} reduction. The significance attached to hard coal as one of today`s prime sources of energy with the largest reserves worldwide, and, consequently, its importance for use in power generation, is certain to increase in the years to come. The further development of conventional power plant technology, therefore, is vital, and must be carried out on the basis of proven operational experience. The main incentive behind the development work completed so far has been, and continues to be, the achievement of cost reductions and environmental benefits in the generation of electricity by increasing plant efficiency, and this means that, in both the short and the long term, power plants with improved conventional technology will be used for environmentally acceptable coal-fired power generation.

  18. The potential of renewables versus natural gas with CO2 capture and storage for power generation under CO2 constraints

    NARCIS (Netherlands)

    Van Den Broek, Machteld|info:eu-repo/dai/nl/092946895; Berghout, Niels|info:eu-repo/dai/nl/328201057; Rubin, Edward S.

    2015-01-01

    The costs of intermittent renewable energy systems (IRES) and power storage technologies are compared on a level playing field to those of natural gas combined cycle power plants with CO2 capture and storage (NGCC-CCS). To account for technological progress over time, an "experience curve

  19. The potential of renewables versus natural gas with CO2 capture and storage for power generation under CO2 constraints

    NARCIS (Netherlands)

    Van Den Broek, Machteld; Berghout, Niels; Rubin, Edward S.

    2015-01-01

    The costs of intermittent renewable energy systems (IRES) and power storage technologies are compared on a level playing field to those of natural gas combined cycle power plants with CO2 capture and storage (NGCC-CCS). To account for technological progress over time, an "experience curve

  20. Thermodynamic assessment of amine based CO2 capture technologies in power plants based on European Benchmarking Task Force methodology

    NARCIS (Netherlands)

    Sanchez Fernandez, E.; Goetheer, E.L.V.; Manzolini, G.; Macchi, E.; Rezvani, S.; Vlugt, T.J.H.

    2014-01-01

    Post combustion CO2 capture (PCC) with amine solvents is seen as one of the possible technologies which can be implemented in the near term to significantly reduce CO2 emissions from fossil fuel power plants. One of the major concerns for its implementation at large scale in power plants is the high

  1. Predicting the ultimate potential of natural gas SOFC power cycles with CO2 capture : Part B: Applications

    NARCIS (Netherlands)

    Campanari, Stefano; Mastropasqua, Luca; Gazzani, Matteo|info:eu-repo/dai/nl/412517361; Chiesa, Paolo; Romano, Matteo C.

    2016-01-01

    An important advantage of solid oxide fuel cells (SOFC) as future systems for large scale power generation is the possibility of being efficiently integrated with processes for CO2 capture. Focusing on natural gas power generation, Part A of this work assessed the performances of advanced

  2. Thermodynamic assessment of amine based CO2 capture technologies in power plants based on European Benchmarking Task Force methodology

    NARCIS (Netherlands)

    Sanchez Fernandez, E.; Goetheer, E.L.V.; Manzolini, G.; Macchi, E.; Rezvani, S.; Vlugt, T.J.H.

    2014-01-01

    Post combustion CO2 capture (PCC) with amine solvents is seen as one of the possible technologies which can be implemented in the near term to significantly reduce CO2 emissions from fossil fuel power plants. One of the major concerns for its implementation at large scale in power plants is the high

  3. The potential of renewables versus natural gas with CO2 capture and storage for power generation under CO2 constraints

    NARCIS (Netherlands)

    Van Den Broek, Machteld; Berghout, Niels; Rubin, Edward S.

    2015-01-01

    The costs of intermittent renewable energy systems (IRES) and power storage technologies are compared on a level playing field to those of natural gas combined cycle power plants with CO2 capture and storage (NGCC-CCS). To account for technological progress over time, an "experience

  4. Improving Electrical Efficiency of Edm Power Supply

    Science.gov (United States)

    Toma, Emanoil; Simion, Carmen Mihaela

    2014-11-01

    This paper briefly presents the principal types of Pulse Generators for Electrical Discharge Machining and ways to improve electrical efficiency. A resonant converter with series-parallel LCC circuit, for EDM applications, was analyzed by PSpice simulation. The performances of EDM Power Supply were improved by adding an energy recovering - voltage limiter circuit. The shape of current pulse was changed by adding a supplementary MOSFET Switch in parallel with the gap. Two or more converters can be parallelized, in this way output current can be changed. A bloc-schema was conceived for EDM experimental set up

  5. Construct ability Improvement for Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dae Soo; Lee, Jong Rim; Kim, Jong Ku [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

    1997-12-31

    The purpose of this study was to identify methods for improving the construct ability of nuclear power plants. This study reviewed several references of current construction practices of domestic and overseas nuclear plants in order to identify potential methods for improving construct ability. The identified methods for improving construct ability were then evaluated based on the applicability to domestic nuclear plant construction. The selected methods are expected to reduce the construction period, improve the quality of construction, cost, safety, and productivity. Selection of which methods should be implemented will require further evaluation of construction modifications, design changes, contract revisions. Among construction methods studied, platform construction methods can be applied through construction sequence modification without significant design changes, and Over the Top construction method of the NSSS, automatic welding of RCL pipes, CLP modularization, etc., are considered to be applied after design modification and adjustment of material lead time. (author). 49 refs., figs., tabs.

  6. Muscle trade-offs in a power-amplified prey capture system.

    Science.gov (United States)

    Blanco, M Mendoza; Patek, S N

    2014-05-01

    Should animals operating at great speeds and accelerations use fast or slow muscles? The answer hinges on a fundamental trade-off: muscles can be maximally fast or forceful, but not both. Direct lever systems offer a straightforward manifestation of this trade-off, yet the fastest organisms use power amplification, not direct lever action. Power-amplified systems typically use slow, forceful muscles to preload springs, which then rapidly release elastic potential energy to generate high speeds and accelerations. However, a fast response to a stimulus may necessitate fast spring-loading. Across 22 mantis shrimp species (Stomatopoda), this study examined how muscle anatomy correlates with spring mechanics and appendage type. We found that muscle force is maximized through physiological cross-sectional area, but not through sarcomere length. Sit-and-wait predators (spearers) had the shortest sarcomere lengths (fastest contractions) and the slowest strike speeds. The species that crush shells (smashers) had the fastest speeds, most forceful springs, and longest sarcomeres. The origin of the smasher clade yielded dazzlingly high accelerations, perhaps due to the release from fast spring-loading for evasive prey capture. This study offers a new window into the dynamics of force-speed trade-offs in muscles in the biomechanical, comparative evolutionary framework of power-amplified systems. © 2014 The Author(s). Evolution © 2014 The Society for the Study of Evolution.

  7. MOCA: A Low-Power, Low-Cost Motion Capture System Based on Integrated Accelerometers

    Directory of Open Access Journals (Sweden)

    Elisabetta Farella

    2007-01-01

    Full Text Available Human-computer interaction (HCI and virtual reality applications pose the challenge of enabling real-time interfaces for natural interaction. Gesture recognition based on body-mounted accelerometers has been proposed as a viable solution to translate patterns of movements that are associated with user commands, thus substituting point-and-click methods or other cumbersome input devices. On the other hand, cost and power constraints make the implementation of a natural and efficient interface suitable for consumer applications a critical task. Even though several gesture recognition solutions exist, their use in HCI context has been poorly characterized. For this reason, in this paper, we consider a low-cost/low-power wearable motion tracking system based on integrated accelerometers called motion capture with accelerometers (MOCA that we evaluated for navigation in virtual spaces. Recognition is based on a geometric algorithm that enables efficient and robust detection of rotational movements. Our objective is to demonstrate that such a low-cost and a low-power implementation is suitable for HCI applications. To this purpose, we characterized the system from both a quantitative point of view and a qualitative point of view. First, we performed static and dynamic assessment of movement recognition accuracy. Second, we evaluated the effectiveness of user experience using a 3D game application as a test bed.

  8. The cost of carbon capture and storage for natural gas combined cycle power plants.

    Science.gov (United States)

    Rubin, Edward S; Zhai, Haibo

    2012-03-20

    This paper examines the cost of CO(2) capture and storage (CCS) for natural gas combined cycle (NGCC) power plants. Existing studies employ a broad range of assumptions and lack a consistent costing method. This study takes a more systematic approach to analyze plants with an amine-based postcombustion CCS system with 90% CO(2) capture. We employ sensitivity analyses together with a probabilistic analysis to quantify costs for plants with and without CCS under uncertainty or variability in key parameters. Results for new baseload plants indicate a likely increase in levelized cost of electricity (LCOE) of $20-32/MWh (constant 2007$) or $22-40/MWh in current dollars. A risk premium for plants with CCS increases these ranges to $23-39/MWh and $25-46/MWh, respectively. Based on current cost estimates, our analysis further shows that a policy to encourage CCS at new NGCC plants via an emission tax or carbon price requires (at 95% confidence) a price of at least $125/t CO(2) to ensure NGCC-CCS is cheaper than a plant without CCS. Higher costs are found for nonbaseload plants and CCS retrofits.

  9. Improving the Electronic Capture of Advance Care Directives in a Healthcare Delivery System.

    Science.gov (United States)

    Kamo, Norifumi; Williams, Barbara L; Smith, Donna L; Blackmore, C Craig

    2017-05-01

    To determine the effectiveness of a multifaceted quality improvement intervention in outpatient clinics at an integrated healthcare delivery system on capture rate of advance directives (ADs) in the electronic medical record (EMR). Interrupted time series analysis with control groups between January 2010 and June 2015. Oncology, nephrology, and primary care outpatient clinics in an integrated healthcare delivery system. All individuals aged 65 and older with at least one office visit in any outpatient clinic in the care delivery system (n = 77,350 with 502,446 office visits). A series of quality improvement interventions to improve rates of advance care planning discussions and capture of those discussions in the EMR between 2010 and 2014. Capture rate of ADs in the EMR. Visits in the intervention primary care clinic were twice as likely to mention ADs in the EMR (53.4%) than visits in nonintervention primary care clinics (26.5%). Visits in the intervention oncology clinic were more than eight times as likely to mention ADs in the EMR (49.3% vs 6.0%), and visits in the intervention nephrology clinic were 2.5 times as likely to mention ADs (15.4% vs 6.0%) than visits in other specialty clinics. A series of quality improvement interventions to increase discussions about advance care planning and capture of advance care directives in the EMR significantly increased the rate of capture in primary care and specialty care outpatient settings. © 2017, Copyright the Authors Journal compilation © 2017, The American Geriatrics Society.

  10. Power generation enhancement in novel microbial carbon capture cells with immobilized Chlorella vulgaris

    Science.gov (United States)

    Zhou, Minghua; He, Huanhuan; Jin, Tao; Wang, Hongyu

    2012-09-01

    With the increasing concerns for global climate change, a sustainable, efficient and renewable energy production from wastewater is imperative. In this study, a novel microbial carbon capture cell (MCC), is constructed for the first time by the introduction of immobilized microalgae (Chlorella vulgaris) into the cathode chamber of microbial fuel cells (MFCs) to fulfill the zero discharge of carbon dioxide. This process can achieve an 84.8% COD removal, and simultaneously the maximum power density can reach 2485.35 mW m-3 at a current density of 7.9 A m-3 and the Coulombic efficiency is 9.40%, which are 88% and 57.7% greater than that with suspended C. vulgaris, respectively. These enhancements in performance demonstrate the feasibility of an economical and effective approach for the simultaneous wastewater treatment, electricity generation and biodiesel production from microalgae.

  11. CO2 capture from power plants. Part II : A parametric study of the economical performance based on mono-ethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, M. R. M.; Niederer, J. P. M.; Feron, P. H. M.; Versteeg, G. F.

    2007-01-01

    While the demand for reduction in CO2 emission is increasing, the cost of the CO2 capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in t

  12. CO2 capture from power plants: Part II. A parametric study of the economical performance based on mono-ethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, Mohammad R.M.; Niederer, John; Feron, Paul H.M.; Versteeg, Geert

    2007-01-01

    While the demand for reduction in CO2 emission is increasing, the cost of the CO2 capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in

  13. CO2 capture from power plants. Part II : A parametric study of the economical performance based on mono-ethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, M. R. M.; Niederer, J. P. M.; Feron, P. H. M.; Versteeg, G. F.

    While the demand for reduction in CO2 emission is increasing, the cost of the CO2 capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in

  14. CO2 capture from power plants: Part II. A parametric study of the economical performance based on mono-ethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, Mohammad R.M.; Niederer, John P.M.; Feron, Paul H.M.; Versteeg, Geert F.

    2007-01-01

    While the demand for reduction in CO2 emission is increasing, the cost of the CO2 capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in t

  15. CO2 capture from power plants. Part II : A parametric study of the economical performance based on mono-ethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, M. R. M.; Niederer, J. P. M.; Feron, P. H. M.; Versteeg, G. F.

    2007-01-01

    While the demand for reduction in CO2 emission is increasing, the cost of the CO2 capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in t

  16. Lead/acid batteries in systems to improve power quality

    Science.gov (United States)

    Taylor, P.; Butler, P.; Nerbun, W.

    Increasing dependence on computer technology is driving needs for extremely high-quality power to prevent loss of information, material, and workers' time that represent billions of dollars annually. This cost has motivated commercial and Federal research and development of energy storage systems that detect and respond to power-quality failures in milliseconds. Electrochemical batteries are among the storage media under investigation for these systems. Battery energy storage systems that employ either flooded lead/acid or valve-regulated lead/acid battery technologies are becoming commercially available to capture a share of this emerging market. Cooperative research and development between the US Department of Energy and private industry have led to installations of lead/acid-based battery energy storage systems to improve power quality at utility and industrial sites and commercial development of fully integrated, modular battery energy storage system products for power quality. One such system by AC Battery Corporation, called the PQ2000, is installed at a test site at Pacific Gas and Electric Company (San Ramon, CA, USA) and at a customer site at Oglethorpe Power Corporation (Tucker, GA, USA). The PQ2000 employs off-the-shelf power electronics in an integrated methodology to control the factors that affect the performance and service life of production-model, low-maintenance, flooded lead/acid batteries. This system, and other members of this first generation of lead/acid-based energy storage systems, will need to compete vigorously for a share of an expanding, yet very aggressive, power quality market.

  17. Concentrating solar power (CSP) power cycle improvements through application of advanced materials

    Science.gov (United States)

    Siefert, John A.; Libby, Cara; Shingledecker, John

    2016-05-01

    Concentrating solar power (CSP) systems with thermal energy storage (TES) capability offer unique advantages to other renewable energy technologies in that solar radiation can be captured and stored for utilization when the sun is not shining. This makes the technology attractive as a dispatchable resource, and as such the Electric Power Research Institute (EPRI) has been engaged in research and development activities to understand and track the technology, identify key technical challenges, and enable improvements to meet future cost and performance targets to enable greater adoption of this carbon-free energy resource. EPRI is also involved with technically leading a consortium of manufacturers, government labs, and research organizations to enable the next generation of fossil fired power plants with advanced ultrasupercritical (A-USC) steam temperatures up to 760°C (1400°F). Materials are a key enabling technology for both of these seemingly opposed systems. This paper discusses how major strides in structural materials for A-USC fossil fired power plants may be translated into improved CSP systems which meet target requirements.

  18. TIG welding power supply with improved efficiency

    Directory of Open Access Journals (Sweden)

    Сергій Володимирович Гулаков

    2015-03-01

    Full Text Available In the article, the influence of the DC component of the welding current during TIG (Tungsten Inert Gas welding is discussed. Known methods of DC current cancellation are reviewed, such as capacitor bank or diode/thyristor network insertion in the secondary circuit of the welding transformer. A new method of controlling the magnitude and shape of the TIG welding current is proposed. The idea is to insert a controlled voltage source in the secondary circuit of the welding transformer. This controlled voltage source is realized using a full-bridge voltage source inverter (VSI. VSI control system design issues are discussed. VSI is controlled by a three-level hysteretic current controller, while current reference is generated using lookup table driven by PLL (Phase Locked Loop locked to the mains frequency. Simulation results are shown. The proposed topology of TIG power supply allows to provide magnitude and shape control of the welding current, with the limitation that its DC component must be zero. Thus, some capabilities of professional AC-TIG welders are obtained using substantially lower cost components: VSI built using high-current low voltage MOSFETs with control system based on 32-bit ARM microcontroller. The use of proposed TIG welding power supply will eliminate the DC component of the welding current, improve welding transformer’s power factor and improve welding technology by increasing the welding arc stability

  19. Development of a Dry Sorbent-based Post-Combustion CO2 Capture Technology for Retrofit in Existing Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Thomas; Coleman, Luke; Anderson, Matthew; Gupta, Raghubir; Herr, Joshua; Kalluri, Ranjeeth; Pavani, Maruthi

    2009-12-31

    The objective of this research and development (R&D) project was to further the development of a solid sorbent-based CO2 capture process based on sodium carbonate (i.e. the Dry Carbonate Process) that is capable of capturing>90% of the CO2 as a nearly pure stream from coal-fired power plant flue gas with <35% increase in the cost of electrictiy (ICOE).

  20. Integration between a demo size post-combustion CO2 capture and full size power plant: an integral approach on energy penalty for different process options

    NARCIS (Netherlands)

    Miguel Mercader, F. de; Magneschi, G.; Sanchez Fernandez, E.; Stienstra, G.J.; Goetheer, E.L.V.

    2012-01-01

    CO2 capture based on post-combustion capture has the potential to significantly reduce the CO2 emissions from coal-fired power plants. However, this capture process reduces considerably the energy efficiency of the power plant. To reduce this energy penalty, this paper studies different

  1. Integration between a demo size post-combustion CO2 capture and full size power plant: an integral approach on energy penalty for different process options

    NARCIS (Netherlands)

    Miguel Mercader, F. de; Magneschi, G.; Sanchez Fernandez, E.; Stienstra, G.J.; Goetheer, E.L.V.

    2012-01-01

    CO2 capture based on post-combustion capture has the potential to significantly reduce the CO2 emissions from coal-fired power plants. However, this capture process reduces considerably the energy efficiency of the power plant. To reduce this energy penalty, this paper studies different post-combust

  2. Thermodynamic simulation of CO{sub 2} capture for an IGCC power plant using the calcium looping cycle

    Energy Technology Data Exchange (ETDEWEB)

    Li, Y. [National Engineering Laboratory for Coal-Burning Pollutant Emission Reduction, Shandong University, Jinan (China); Zhao, C.; Ren, Q. [School of Energy and Environment, Southeast University, Nanjing (China)

    2011-06-15

    A CO{sub 2} capture process for an integrated gasification combined cycle (IGCC) power plant using the calcium looping cycle was proposed. The CO{sub 2} capture process using natural and modified limestone was simulated and investigated with the software package Aspen Plus. It incorporated a fresh feed of sorbent to compensate for the decay in CO{sub 2} capture activity during long-term cycles. The sorbent flow ratios have significant effect on the CO{sub 2} capture efficiency and net efficiency of the CO{sub 2} capture system. The IGCC power plant, using the modified limestone, exhibits higher CO{sub 2} capture efficiency than that using the natural limestone at the same sorbent flow ratios. The system net efficiency using the natural and modified limestones achieves 41.7% and 43.1%, respectively, at the CO{sub 2} capture efficiency of 90% without the effect of sulfation. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. A TECHNICAL, ECONOMIC AND ENVIRONMENTAL ASSESSMENT OF AMINE-BASED CO2 CAPTURE TECHNOLOGY FOR POWER PLANT GREENHOUSE GAS CONTROL

    Energy Technology Data Exchange (ETDEWEB)

    Edward S. Rubin; Anand B. Rao

    2002-10-01

    Capture and sequestration of CO{sub 2} from fossil fuel power plants is gaining widespread interest as a potential method of controlling greenhouse gas emissions. Performance and cost models of an amine (MEA)-based CO{sub 2} absorption system for post-combustion flue gas applications have been developed, and integrated with an existing power plant modeling framework that includes multi-pollutant control technologies for other regulated emissions. The integrated model has been applied to study the feasibility and cost of carbon capture and sequestration at both new and existing coal-burning power plants. The cost of carbon avoidance was shown to depend strongly on assumptions about the reference plant design, details of the CO{sub 2} capture system design, interactions with other pollution control systems, and method of CO{sub 2} storage. The CO{sub 2} avoidance cost for retrofit systems was found to be generally higher than for new plants, mainly because of the higher energy penalty resulting from less efficient heat integration, as well as site-specific difficulties typically encountered in retrofit applications. For all cases, a small reduction in CO{sub 2} capture cost was afforded by the SO{sub 2} emission trading credits generated by amine-based capture systems. Efforts are underway to model a broader suite of carbon capture and sequestration technologies for more comprehensive assessments in the context of multi-pollutant environmental management.

  4. A technical, economic, and environmental assessment of amine-based CO2 capture technology for power plant greenhouse gas control.

    Science.gov (United States)

    Rao, Anand B; Rubin, Edward S

    2002-10-15

    Capture and sequestration of CO2 from fossil fuel power plants is gaining widespread interest as a potential method of controlling greenhouse gas emissions. Performance and cost models of an amine (MEA)-based CO2 absorption system for postcombustion flue gas applications have been developed and integrated with an existing power plant modeling framework that includes multipollutant control technologies for other regulated emissions. The integrated model has been applied to study the feasibility and cost of carbon capture and sequestration at both new and existing coal-burning power plants. The cost of carbon avoidance was shown to depend strongly on assumptions about the reference plant design, details of the CO2 capture system design, interactions with other pollution control systems, and method of CO2 storage. The CO2 avoidance cost for retrofit systems was found to be generally higher than for new plants, mainly because of the higher energy penalty resulting from less efficient heat integration as well as site-specific difficulties typically encountered in retrofit applications. For all cases, a small reduction in CO2 capture cost was afforded by the SO2 emission trading credits generated by amine-based capture systems. Efforts are underway to model a broader suite of carbon capture and sequestration technologies for more comprehensive assessments in the context of multipollutant environmental management.

  5. High-power liquid-lithium target prototype for accelerator-based boron neutron capture therapy.

    Science.gov (United States)

    Halfon, S; Paul, M; Arenshtam, A; Berkovits, D; Bisyakoev, M; Eliyahu, I; Feinberg, G; Hazenshprung, N; Kijel, D; Nagler, A; Silverman, I

    2011-12-01

    A prototype of a compact Liquid-Lithium Target (LiLiT), which will possibly constitute an accelerator-based intense neutron source for Boron Neutron Capture Therapy (BNCT) in hospitals, was built. The LiLiT setup is presently being commissioned at Soreq Nuclear Research Center (SNRC). The liquid-lithium target will produce neutrons through the (7)Li(p,n)(7)Be reaction and it will overcome the major problem of removing the thermal power generated using a high-intensity proton beam (>10 kW), necessary for sufficient neutron flux. In off-line circulation tests, the liquid-lithium loop generated a stable lithium jet at high velocity, on a concave supporting wall; the concept will first be tested using a high-power electron beam impinging on the lithium jet. High intensity proton beam irradiation (1.91-2.5 MeV, 2-4 mA) will take place at Soreq Applied Research Accelerator Facility (SARAF) superconducting linear accelerator currently in construction at SNRC. Radiological risks due to the (7)Be produced in the reaction were studied and will be handled through a proper design, including a cold trap and appropriate shielding. A moderator/reflector assembly is planned according to a Monte Carlo simulation, to create a neutron spectrum and intensity maximally effective to the treatment and to reduce prompt gamma radiation dose risks.

  6. Control system design for maintaining CO{sub 2} capture in IGCC power plants while loading-following

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharyya, D.; Turton, R.; Zitney, S.

    2012-01-01

    Load-following requirements for future integrated gasification combined cycle (IGCC) power plants with precombustion CO{sub 2} capture are expected to be far more challenging as electricity produced by renewable energy is connected to the grid and strict environmental limits become mandatory requirements. In this work, loadfollowing studies are performed using a comprehensive dynamic model of an IGCC plant with pre-combustion CO{sub 2} capture developed in Aspen Engineering Suite (AES). Considering multiple single-loop controllers for power demand load following, the preferred IGCC control strategy from the perspective of a power producer is gas turbine (GT) lead with gasifier follow. In this strategy, the GT controls the load by manipulating its firing rate while the slurry feed flow to the gasifier is manipulated to control the syngas pressure at the GT inlet. The syngas pressure control is an integrating process with significant time delay mainly because of the large piping and equipment volumes between the gasifier and the GT inlet. A modified proportional–integral–derivative (PID) control is considered for IGCC syngas pressure control. The desired CO{sub 2} capture rate must be maintained while the IGCC plant follows the load. For maintaining the desired CO{sub 2} capture rate, the control performance of PID control is compared with linear model predictive control (LMPC). The results show that the LMPC outperforms PID control for maintaining CO{sub 2} capture rates in an IGCC power plant while load following.

  7. Calcium and chemical looping technology for power generation and carbon dioxide (CO2) capture solid oxygen- and CO2-carriers

    CERN Document Server

    Fennell, Paul

    2015-01-01

    Calcium and Chemical Looping Technology for Power Generation and Carbon Dioxide (CO2) Capture reviews the fundamental principles, systems, oxygen carriers, and carbon dioxide carriers relevant to chemical looping and combustion. Chapters review the market development, economics, and deployment of these systems, also providing detailed information on the variety of materials and processes that will help to shape the future of CO2 capture ready power plants. Reviews the fundamental principles, systems, oxygen carriers, and carbon dioxide carriers relevant to calcium and chemical loopingProvi

  8. CFD Simulations of a Regenerative Process for Carbon Dioxide Capture in Advanced Gasification Based Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Arastoopour, Hamid [Illinois Inst. of Technology, Chicago, IL (United States); Abbasian, Javad [Illinois Inst. of Technology, Chicago, IL (United States)

    2014-07-31

    the method of moments, called Finite size domain Complete set of trial functions Method Of Moments (FCMOM) was used to solve the population balance equations. The PBE model was implemented in a commercial CFD code, Ansys Fluent 13.0. The code was used to test the model in some simple cases and the results were verified against available analytical solution in the literature. Furthermore, the code was used to simulate CO2 capture in a packed-bed and the results were in excellent agreement with the experimental data obtained in the packed bed. The National Energy Laboratory (NETL) Carbon Capture Unit (C2U) design was used in simulate of the hydrodynamics of the cold flow gas/solid system (Clark et al.58). The results indicate that the pressure drop predicted by the model is in good agreement with the experimental data. Furthermore, the model was shown to be able to predict chugging behavior, which was observed during the experiment. The model was used as a base-case for simulations of reactive flow at elevated pressure and temperatures. The results indicate that by controlling the solid circulation rate, up to 70% CO2 removal can be achieved and that the solid hold up in the riser is one of the main factors controlling the extent of CO2 removal. The CFD/PBE simulation model indicates that by using a simulated syngas with a composition of 20% CO2, 20% H2O, 30% CO, and 30% H2, the composition (wet basis) in the reactor outlet corresponded to about 60% CO2 capture with and exit gas containing 65% H2. A preliminary base-case-design was developed for a regenerative MgO-based pre-combustion carbon capture process for a 500 MW IGCC power plant. To minimize the external energy requirement, an extensive heat integration network was developed in Aspen/HYSYS® to produce the steam required in the regenerator and heat integration. In this process, liquid CO2 produced at 50 atm can easily be pumped and sequestered or stored. The preliminary economic analyses indicate that the

  9. Antigen-capturing nanoparticles improve the abscopal effect and cancer immunotherapy

    Science.gov (United States)

    Min, Yuanzeng; Roche, Kyle C.; Tian, Shaomin; Eblan, Michael J.; McKinnon, Karen P.; Caster, Joseph M.; Chai, Shengjie; Herring, Laura E.; Zhang, Longzhen; Zhang, Tian; Desimone, Joseph M.; Tepper, Joel E.; Vincent, Benjamin G.; Serody, Jonathan S.; Wang, Andrew Z.

    2017-09-01

    Immunotherapy holds tremendous promise for improving cancer treatment. To administer radiotherapy with immunotherapy has been shown to improve immune responses and can elicit the 'abscopal effect'. Unfortunately, response rates for this strategy remain low. Herein we report an improved cancer immunotherapy approach that utilizes antigen-capturing nanoparticles (AC-NPs). We engineered several AC-NP formulations and demonstrated that the set of protein antigens captured by each AC-NP formulation is dependent on the NP surface properties. We showed that AC-NPs deliver tumour-specific proteins to antigen-presenting cells (APCs) and significantly improve the efficacy of αPD-1 (anti-programmed cell death 1) treatment using the B16F10 melanoma model, generating up to a 20% cure rate compared with 0% without AC-NPs. Mechanistic studies revealed that AC-NPs induced an expansion of CD8+ cytotoxic T cells and increased both CD4+T/Treg and CD8+T/Treg ratios (Treg, regulatory T cells). Our work presents a novel strategy to improve cancer immunotherapy with nanotechnology.

  10. Projected techno-economic improvements for advanced solar thermal power plants

    Science.gov (United States)

    Fujita, T.; Manvi, R.; Roschke, E. J.

    1979-01-01

    The projected characteristics of solar thermal power plants (with outputs up to 10 MWe) employing promising advanced technology subsystems/components are compared to current (or pre-1985) steam-Rankine systems. Improvements accruing to advanced technology development options are delineated. The improvements derived from advanced systems result primarily from achieving high efficiencies via solar collector systems which (1) capture a large portion of the available insolation and (2) concentrate this captured solar flux to attain high temperatures required for high heat engine/energy conversion performance. The most efficient solar collector systems employ two-axis tracking. Attractive systems include the central receiver/heliostat and the parabolic dish.

  11. Improved Visual Hook Capturing and Tracking for Precision Hoisting of Tower Crane

    Directory of Open Access Journals (Sweden)

    Yanming Li

    2013-01-01

    Full Text Available To maintain safe operation of the tower crane, it is important to monitor the activities of the hook system. Visual monitoring and image recognition are the optimum methods for crane hook tracking and precision hoisting. High real-time performance and low computation requirements are required for tower crane hook capturing and tracking system which is implemented on the embedded Advanced RISC Machines (ARM processor or Microcontrol Unit (MCU. Using the lift rope of a tower crane as the target object, a new high-performance hook tracking method suitble for ARM processor or MCU applications is presented. The features of the lifting process are analyzed, and an improved progressive probabilistic Hough transform (IPPHT algorithm is proposed which canreduce capturing time by up to 80%. Combining color histogram with a binary search algorithm, an adaptive zooming method for precise hoisting is presented. Using this method the optimum zoom scale can be achieved within a few iterations.

  12. Improved cooling design for high power waveguide system

    Science.gov (United States)

    Chen, W. C. J.; Hartop, R.

    1981-06-01

    Testing of X band high power components in a traveling wave resonator indicates that this improved cooling design reduces temperature in the waveguide and flange. The waveguide power handling capability and power transmission reliability is increased substantially.

  13. Power generation from coal and biomass based on integrated gasification combined cycle concept with pre- and post-combustion carbon capture methods

    Energy Technology Data Exchange (ETDEWEB)

    Calin-Cristian Cormos; Ana-Maria Cormos; Serban Agachi [Babes-Bolyai University, Cluj-Napoca (Romania)

    2009-11-15

    Gasification technology is a process in which solid fuel is partially oxidised by oxygen and steam/water to produce a combustible gas called syngas (mainly a mixture of hydrogen and carbon monoxide). Syngas can be used either for power generation or processed to obtain various chemicals (hydrogen, ammonia, methanol, etc.). This article evaluates the possibilities of solid fuel decarbonisation by capturing carbon dioxide resulting from thermo-chemical conversion of solid fuel using gasification. Evaluation is focused on power generation technology using syngas produced by solid fuel gasification (so-called integrated gasification combined cycle IGCC). Case studies analysed in the article are using a mixture of coal and biomass (sawdust) to produce around 400 MW electricity simultaneously with capturing about 90% of the feedstock carbon. Various carbon dioxide capture options (post- and pre-combustion) are compared with situation of no carbon capture in terms of plant configurations, energy penalty, CO{sub 2} emissions, etc. Plant options are modelled using ChemCAD, and simulation results are used to assess the plant performances. Plant flexibility and future improvements are also discussed.

  14. Hollow Fiber Membrane Contactors for CO2 Capture: Modeling and Up-Scaling to CO2 Capture for an 800 MWe Coal Power Station

    Directory of Open Access Journals (Sweden)

    Kimball Erin

    2014-11-01

    Full Text Available A techno-economic analysis was completed to compare the use of Hollow Fiber Membrane Modules (HFMM with the more conventional structured packing columns as the absorber in amine-based CO2 capture systems for power plants. In order to simulate the operation of industrial scale HFMM systems, a two-dimensional model was developed and validated based on results of a laboratory scale HFMM. After successful experiments and validation of the model, a pilot scale HFMM was constructed and simulated with the same model. The results of the simulations, from both sizes of HFMM, were used to assess the feasibility of further up-scaling to a HFMM system to capture the CO2 from an 800 MWe power plant. The system requirements – membrane fiber length, total contact surface area, and module volume – were determined from simulations and used for an economic comparison with structured packing columns. Results showed that a significant cost reduction of at least 50% is required to make HFMM competitive with structured packing columns. Several factors for the design of industrial scale HFMM require further investigation, such as the optimal aspect ratio (module length/diameter, membrane lifetime, and casing material and shape, in addition to the need to reduce the overall cost. However, HFMM were also shown to have the advantages of having a higher contact surface area per unit volume and modular scale-up, key factors for applications requiring limited footprints or flexibility in configuration.

  15. CFD Simulations of a Regenerative Process for Carbon Dioxide Capture in Advanced Gasification Based Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Arastoopour, Hamid [Illinois Inst. of Technology, Chicago, IL (United States); Abbasian, Javad [Illinois Inst. of Technology, Chicago, IL (United States)

    2014-07-31

    the method of moments, called Finite size domain Complete set of trial functions Method Of Moments (FCMOM) was used to solve the population balance equations. The PBE model was implemented in a commercial CFD code, Ansys Fluent 13.0. The code was used to test the model in some simple cases and the results were verified against available analytical solution in the literature. Furthermore, the code was used to simulate CO2 capture in a packed-bed and the results were in excellent agreement with the experimental data obtained in the packed bed. The National Energy Laboratory (NETL) Carbon Capture Unit (C2U) design was used in simulate of the hydrodynamics of the cold flow gas/solid system (Clark et al.58). The results indicate that the pressure drop predicted by the model is in good agreement with the experimental data. Furthermore, the model was shown to be able to predict chugging behavior, which was observed during the experiment. The model was used as a base-case for simulations of reactive flow at elevated pressure and temperatures. The results indicate that by controlling the solid circulation rate, up to 70% CO2 removal can be achieved and that the solid hold up in the riser is one of the main factors controlling the extent of CO2 removal. The CFD/PBE simulation model indicates that by using a simulated syngas with a composition of 20% CO2, 20% H2O, 30% CO, and 30% H2, the composition (wet basis) in the reactor outlet corresponded to about 60% CO2 capture with and exit gas containing 65% H2. A preliminary base-case-design was developed for a regenerative MgO-based pre-combustion carbon capture process for a 500 MW IGCC power plant. To minimize the external energy requirement, an extensive heat integration network was developed in Aspen/HYSYS® to produce the steam required in the regenerator and heat integration. In this process, liquid CO2 produced at 50 atm can easily be pumped and sequestered or stored. The preliminary economic analyses indicate that the

  16. Power Quality Improvement Using Hybrid Power Flow Controller in Power System

    Directory of Open Access Journals (Sweden)

    Manidhar Thula ,

    2014-01-01

    Full Text Available This paper discusses the applicability of Hybrid Power Flow Controller (HPFC as an alternative to Unified Power Flow Controller (UPFC for improvement of power system performance. UPFC is a flexible AC transmission system (FACTS device containing two switching converters, one in series and one in shunt. To configure the HPFC, one of the switching converters of the UPFC is replaced by thyristor controlled variable impedances, thus reducing the cost. In this paper, the HPFC has been configured by multilevel Voltage Source Converter (VSC used for the shunt compensation branches and a thyristor controlled variable impedance used for series compensation. It is shown that with suitable control the HPFC can inject a voltage of required magnitude in series with the line at any desired angle, just like UPFC. This helps in providing compensation equivalent to UPFC and improving the steady state stability limits of the power system.

  17. Plant growth improvement mediated by nitrate capture in co-composted biochar

    Science.gov (United States)

    Kammann, Claudia I.; Schmidt, Hans-Peter; Messerschmidt, Nicole; Linsel, Sebastian; Steffens, Diedrich; Müller, Christoph; Koyro, Hans-Werner; Conte, Pellegrino; Stephen, Joseph

    2015-01-01

    Soil amendment with pyrogenic carbon (biochar) is discussed as strategy to improve soil fertility to enable economic plus environmental benefits. In temperate soils, however, the use of pure biochar mostly has moderately-negative to -positive yield effects. Here we demonstrate that co-composting considerably promoted biochars’ positive effects, largely by nitrate (nutrient) capture and delivery. In a full-factorial growth study with Chenopodium quinoa, biomass yield increased up to 305% in a sandy-poor soil amended with 2% (w/w) co-composted biochar (BCcomp). Conversely, addition of 2% (w/w) untreated biochar (BCpure) decreased the biomass to 60% of the control. Growth-promoting (BCcomp) as well as growth-reducing (BCpure) effects were more pronounced at lower nutrient-supply levels. Electro-ultra filtration and sequential biochar-particle washing revealed that co-composted biochar was nutrient-enriched, particularly with the anions nitrate and phosphate. The captured nitrate in BCcomp was (1) only partly detectable with standard methods, (2) largely protected against leaching, (3) partly plant-available, and (4) did not stimulate N2O emissions. We hypothesize that surface ageing plus non-conventional ion-water bonding in micro- and nano-pores promoted nitrate capture in biochar particles. Amending (N-rich) bio-waste with biochar may enhance its agronomic value and reduce nutrient losses from bio-wastes and agricultural soils. PMID:26057083

  18. Plant growth improvement mediated by nitrate capture in co-composted biochar

    Science.gov (United States)

    Kammann, Claudia I.; Schmidt, Hans-Peter; Messerschmidt, Nicole; Linsel, Sebastian; Steffens, Diedrich; Müller, Christoph; Koyro, Hans-Werner; Conte, Pellegrino; Stephen, Joseph

    2015-06-01

    Soil amendment with pyrogenic carbon (biochar) is discussed as strategy to improve soil fertility to enable economic plus environmental benefits. In temperate soils, however, the use of pure biochar mostly has moderately-negative to -positive yield effects. Here we demonstrate that co-composting considerably promoted biochars’ positive effects, largely by nitrate (nutrient) capture and delivery. In a full-factorial growth study with Chenopodium quinoa, biomass yield increased up to 305% in a sandy-poor soil amended with 2% (w/w) co-composted biochar (BCcomp). Conversely, addition of 2% (w/w) untreated biochar (BCpure) decreased the biomass to 60% of the control. Growth-promoting (BCcomp) as well as growth-reducing (BCpure) effects were more pronounced at lower nutrient-supply levels. Electro-ultra filtration and sequential biochar-particle washing revealed that co-composted biochar was nutrient-enriched, particularly with the anions nitrate and phosphate. The captured nitrate in BCcomp was (1) only partly detectable with standard methods, (2) largely protected against leaching, (3) partly plant-available, and (4) did not stimulate N2O emissions. We hypothesize that surface ageing plus non-conventional ion-water bonding in micro- and nano-pores promoted nitrate capture in biochar particles. Amending (N-rich) bio-waste with biochar may enhance its agronomic value and reduce nutrient losses from bio-wastes and agricultural soils.

  19. Power Efficiency Improvements through Peak-to-Average Power Ratio Reduction and Power Amplifier Linearization

    Directory of Open Access Journals (Sweden)

    Zhou G Tong

    2007-01-01

    Full Text Available Many modern communication signal formats, such as orthogonal frequency-division multiplexing (OFDM and code-division multiple access (CDMA, have high peak-to-average power ratios (PARs. A signal with a high PAR not only is vulnerable in the presence of nonlinear components such as power amplifiers (PAs, but also leads to low transmission power efficiency. Selected mapping (SLM and clipping are well-known PAR reduction techniques. We propose to combine SLM with threshold clipping and digital baseband predistortion to improve the overall efficiency of the transmission system. Testbed experiments demonstrate the effectiveness of the proposed approach.

  20. Bench-scale Development of an Advanced Solid Sorbent-based CO2 Capture Process for Coal-fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Thomas [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Kataria, Atish [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Soukri, Mustapha [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Farmer, Justin [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Mobley, Paul [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Tanthana, Jak [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Wang, Dongxiang [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Wang, Xiaoxing [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Song, Chunshan [Research Triangle Institute (RTI), Research Triangle Park, NC (United States)

    2015-12-31

    It is increasingly clear that CO2 capture and sequestration (CCS) must play a critical role in curbing worldwide CO2 emissions to the atmosphere. Development of these technologies to cost-effectively remove CO2 from coal-fired power plants is very important to mitigating the impact these power plants have within the world’s power generation portfolio. Currently, conventional CO2 capture technologies, such as aqueous-monoethanolamine based solvent systems, are prohibitively expensive and if implemented could result in a 75 to 100% increase in the cost of electricity for consumers worldwide. Solid sorbent CO2 capture processes – such as RTI’s Advanced Solid Sorbent CO2, Capture Process – are promising alternatives to conventional, liquid solvents. Supported amine sorbents – of the nature RTI has developed – are particularly attractive due to their high CO2 loadings, low heat capacities, reduced corrosivity/volatility and the potential to reduce the regeneration energy needed to carry out CO2 capture. Previous work in this area has failed to adequately address various technology challenges such as sorbent stability and regenerability, sorbent scale-up, improved physical strength and attrition-resistance, proper heat management and temperature control, proper solids handling and circulation control, as well as the proper coupling of process engineering advancements that are tailored for a promising sorbent technology. The remaining challenges for these sorbent processes have provided the framework for the project team’s research and development and target for advancing the technology beyond lab- and bench-scale testing. Under a cooperative agreement with the US Department of Energy, and part of NETL’s CO2 Capture Program, RTI has led an effort to address and mitigate the challenges associated with solid sorbent CO2 capture. The overall objective

  1. Multiple arterial phase MRI of arterial hypervascular hepatic lesions: improved arterial phase capture and lesion enhancement.

    Science.gov (United States)

    Ikram, Nabia S; Yee, Judy; Weinstein, Stefanie; Yeh, Benjamin M; Corvera, Carlos U; Monto, Alexander; Hope, Thomas A

    2017-03-01

    To establish if triple-phase arterial imaging improves the detection of arterial phase hyperintense lesions based on arterial phase capture, motion artifact degradation, and lesion enhancement when compared to single-phase imaging. Patients at risk for hepatocellular carcinoma were imaged at 3.0T. Seventy-three consecutive patients with a standard single-phase MRI and eighty-five consecutive patients were imaged using extracellular contrast with triple arterial phase MRI using three sequential accelerated acquisitions of 8 s. Arterial phase capture and image quality were qualitatively categorized. Forty single-phase and forty-four triple-phase studies contained arterially enhancing lesions > 1 cm with washout appearance. The contrast-to-noise ratio (CNR) of the lesions was calculated. We compared the differences in means with Student t-tests and those in arterial phase capture with a Chi squared test with Yates correction. The triple-phase acquisitions captured the early or late arterial phases more frequently than did the single-phase acquisition (99% vs 86%; P value = 0.006). Triple-phase also provided greater number of patients with early or late arterial phase imaging without motion artifact (92% vs 79%, P-value = 0.05). The lesion analysis revealed increased maximum CNR in the triple-phase imaging (704.4) vs. single-phase imaging (517.2), P-value phase acquisition provides more robust arterial phase imaging for hepatic lesions, with increased lesion CNR, compared to standard single-phase arterial phase imaging.

  2. Opportunities for Decarbonizing Existing U.S. Coal-Fired Power Plants via CO2 Capture, Utilization and Storage.

    Science.gov (United States)

    Zhai, Haibo; Ou, Yang; Rubin, Edward S

    2015-07-07

    This study employs a power plant modeling tool to explore the feasibility of reducing unit-level emission rates of CO2 by 30% by retrofitting carbon capture, utilization, and storage (CCUS) to existing U.S. coal-fired electric generating units (EGUs). Our goal is to identify feasible EGUs and their key attributes. The results indicate that for about 60 gigawatts of the existing coal-fired capacity, the implementation of partial CO2 capture appears feasible, though its cost is highly dependent on the unit characteristics and fuel prices. Auxiliary gas-fired boilers can be employed to power a carbon capture process without significant increases in the cost of electricity generation. A complementary CO2 emission trading program can provide additional economic incentives for the deployment of CCS with 90% CO2 capture. Selling and utilizing the captured CO2 product for enhanced oil recovery can further accelerate CCUS deployment and also help reinforce a CO2 emission trading market. These efforts would allow existing coal-fired EGUs to continue to provide a significant share of the U.S. electricity demand.

  3. Development of Fly Ash Derived Sorbents to Capture CO2 from Flue Gas of Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    M. Mercedes Maroto-Valer; John M. Andresen; Yinzhi Zhang; Zhe Lu

    2003-12-31

    This research program focused on the development of fly ash derived sorbents to capture CO{sub 2} from power plant flue gas emissions. The fly ash derived sorbents developed represent an affordable alternative to existing methods using specialized activated carbons and molecular sieves, that tend to be very expensive and hinder the viability of the CO{sub 2} sorption process due to economic constraints. Under Task 1 'Procurement and characterization of a suite of fly ashes', 10 fly ash samples, named FAS-1 to -10, were collected from different combustors with different feedstocks, including bituminous coal, PRB coal and biomass. These samples presented a wide range of LOI value from 0.66-84.0%, and different burn-off profiles. The samples also spanned a wide range of total specific surface area and pore volume. These variations reflect the difference in the feedstock, types of combustors, collection hopper, and the beneficiation technologies the different fly ashes underwent. Under Task 2 'Preparation of fly ash derived sorbents', the fly ash samples were activated by steam. Nitrogen adsorption isotherms were used to characterize the resultant activated samples. The cost-saving one-step activation process applied was successfully used to increase the surface area and pore volume of all the fly ash samples. The activated samples present very different surface areas and pore volumes due to the range in physical and chemical properties of their precursors. Furthermore, one activated fly ash sample, FAS-4, was loaded with amine-containing chemicals (MEA, DEA, AMP, and MDEA). The impregnation significantly decreased the surface area and pore volume of the parent activated fly ash sample. Under Task 3 'Capture of CO{sub 2} by fly ash derived sorbents', sample FAS-10 and its deashed counterpart before and after impregnation of chemical PEI were used for the CO{sub 2} adsorption at different temperatures. The sample FAS-10 exhibited a CO{sub 2

  4. Improved Refractories for IGCC Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Dogan, Cynthia P.; Kwong, Kyei-Sing; Bennett, James P.; Chinn, Richard E.; Dahlin, Cheryl L.

    2002-01-01

    The gasification of coal, petroleum residuals, and biomass provides the opportunity to produce energy more efficiently, and with significantly less environmental impact, than more-conventional combustion-based processes. In addition, the synthesis gas that is the product of the gasification process offers the gasifier operator the option of ''polygeneration'', i.e., the production of alternative products instead of power should it be economically favorable to do so. Because of these advantages, gasification is a key element in the U.S. Department of Energy?s Vision 21 power system. However, issues with both the reliability and the economics of gasifier operation will have to be resolved before gasification will be widely adopted by the power industry. Central to both increased reliability and economics is the development of materials with longer service lives in gasifier systems that can provide extended periods of continuous gasifier operation. The focus of the Advanced Refractories for Gasification project at the Albany Research Center is to develop improved materials capable of withstanding the harsh, high-temperature environment created by the gasification reaction, and includes both the refractory lining that insulates the slagging gasifier, as well as the thermocouple assemblies that are utilized to monitor gasifier operating temperatures. Current generation refractory liners in slagging gasifiers are typically replaced every 10 to 18 months, at costs ranging up to $2,000,000. Compounding materials and installation costs are the lost-opportunity costs for the three to four weeks that the gasifier is off-line for the refractory exchange. Current generation thermocouple devices rarely survive the gasifier start-up process, leaving the operator with no real means of temperature measurement during gasifier operation. As a result, the goals of this project include the development of a refractory liner with a service life at least double that of

  5. Sustainability Assessment of Coal-Fired Power Plants with Carbon Capture and Storage

    Energy Technology Data Exchange (ETDEWEB)

    Widder, Sarah H.; Butner, R. Scott; Elliott, Michael L.; Freeman, Charles J.

    2011-11-30

    Carbon capture and sequestration (CCS) has the ability to dramatically reduce carbon dioxide (CO2) emissions from power production. Most studies find the potential for 70 to 80 percent reductions in CO2 emissions on a life-cycle basis, depending on the technology. Because of this potential, utilities and policymakers are considering the wide-spread implementation of CCS technology on new and existing coal plants to dramatically curb greenhouse gas (GHG) emissions from the power generation sector. However, the implementation of CCS systems will have many other social, economic, and environmental impacts beyond curbing GHG emissions that must be considered to achieve sustainable energy generation. For example, emissions of nitrogen oxides (NOx), sulfur oxides (SOx), and particulate matter (PM) are also important environmental concerns for coal-fired power plants. For example, several studies have shown that eutrophication is expected to double and acidification would increase due to increases in NOx emissions for a coal plant with CCS provided by monoethanolamine (MEA) scrubbing. Potential for human health risks is also expected to increase due to increased heavy metals in water from increased coal mining and MEA hazardous waste, although there is currently not enough information to relate this potential to actual realized health impacts. In addition to environmental and human health impacts, supply chain impacts and other social, economic, or strategic impacts will be important to consider. A thorough review of the literature for life-cycle analyses of power generation processes using CCS technology via the MEA absorption process, and other energy generation technologies as applicable, yielded large variability in methods and core metrics. Nonetheless, a few key areas of impact for CCS were developed from the studies that we reviewed. These are: the impact of MEA generation on increased eutrophication and acidification from ammonia emissions and increased toxicity

  6. Power quality improvement in switched mode power supplies using ...

    African Journals Online (AJOL)

    user

    A SEPIC stores the energy in an inductor, and transfers that energy to the output storage capacitor. ..... 2011–2017. ... His areas of interest include power electronics, electrical machines and drives, renewable energy systems, active filters, ...

  7. A Novel Concentrator Photovoltaic (CPV System with the Improvement of Irradiance Uniformity and the Capturing of Diffuse Solar Radiation

    Directory of Open Access Journals (Sweden)

    Nguyen Xuan Tien

    2016-09-01

    Full Text Available This paper proposes a novel concentrator photovoltaic (CPV system with improved irradiation uniformity and system efficiency. CPV technology is very promising its for highly efficient solar energy conversion. A conventional CPV system usually uses only one optical component, such as a refractive Fresnel lens or a reflective parabolic dish, to collect and concentrate solar radiation on the solar cell surface. Such a system creates strongly non-uniform irradiation distribution on the solar cell, which tends to cause hot spots, current mismatch, and degrades the overall efficiency of the system. Additionally, a high-concentration CPV system is unable to collect diffuse solar radiation. In this paper, we propose a novel CPV system with improved irradiation uniformity and collection of diffuse solar radiation. The proposed system uses a Fresnel lens as a primary optical element (POE to concentrate and focus the sunlight and a plano-concave lens as a secondary optical element (SOE to uniformly distribute the sunlight over the surface of multi-junction (MJ solar cells. By using the SOE, the irradiance uniformity is significantly improved in the system. Additionally, the proposed system also captures diffuse solar radiation by using an additional low-cost solar cell surrounding MJ cells. In our system, incident direct solar radiation is captured by MJ solar cells, whereas incident diffuse solar radiation is captured by the low-cost solar cell. Simulation models were developed using a commercial optical simulation tool (LightTools™. The irradiance uniformity and efficiency of the proposed CPV system were analyzed, evaluated, and compared with those of conventional CPV systems. The analyzed and simulated results show that the CPV system significantly improves the irradiance uniformity as well as the system efficiency compared to the conventional CPV systems. Numerically, for our simulation models, the designed CPV with the SOE and low-cost cell provided

  8. Remarks on CO{sub 2} capture from electric power plants and recommendations for future investigations

    Energy Technology Data Exchange (ETDEWEB)

    Wolsky, A.M. [Argonne National Laboratory, IL (United States)

    1993-12-31

    This paper recommends investigation of several topics that have not yet received sustained attention. Each bears directly on the cost and funding of CO{sub 2} capture and sequestration. The reasons why each topic deserves attention are briefly sketched.

  9. Improving electrofishing catch consistency by standardizing power

    Science.gov (United States)

    Burkhardt, Randy W.; Gutreuter, Steve

    1995-01-01

    The electrical output of electrofishing equipment is commonly standardized by using either constant voltage or constant amperage, However, simplified circuit and wave theories of electricity suggest that standardization of power (wattage) available for transfer from water to fish may be critical for effective standardization of electrofishing. Electrofishing with standardized power ensures that constant power is transferable to fish regardless of water conditions. The in situ performance of standardized power output is poorly known. We used data collected by the interagency Long Term Resource Monitoring Program (LTRMP) in the upper Mississippi River system to assess the effectiveness of standardizing power output. The data consisted of 278 electrofishing collections, comprising 9,282 fishes in eight species groups, obtained during 1990 from main channel border, backwater, and tailwater aquatic areas in four reaches of the upper Mississippi River and one reach of the Illinois River. Variation in power output explained an average of 14.9% of catch variance for night electrofishing and 12.1 % for day electrofishing. Three patterns in catch per unit effort were observed for different species: increasing catch with increasing power, decreasing catch with increasing power, and no power-related pattern. Therefore, in addition to reducing catch variation, controlling power output may provide some capability to select particular species. The LTRMP adopted standardized power output beginning in 1991; standardized power output is adjusted for variation in water conductivity and water temperature by reference to a simple chart. Our data suggest that by standardizing electrofishing power output, the LTRMP has eliminated substantial amounts of catch variation at virtually no additional cost.

  10. Capturing CO2 from Coal-Fired Power Plants: Challenges for a Comprehensive Strategy

    Science.gov (United States)

    2008-08-15

    Pre-Combustion CO2 Capture . . . . . . . . . . . . 7 Figure 3. Status of Global IGCC Projects... IGCC is an electric generating technology in which pulverized coal is not burned directly but mixed with oxygen and water in a high-pressure gasifier to...combustion capture of CO2 is the use of Integrated Gasification Combined-cycle ( IGCC ) technology to generate electricity.19 There are currently four

  11. Exploring the potential impact of implementing carbon capture technologies in fossil fuel power plants on regional European water stress index levels

    NARCIS (Netherlands)

    Schakel, W.B.; Pfister, Stephan; Ramirez, C.A.

    2015-01-01

    Equipping power plants with carbon capture technology can affect cooling demand and water use. This study has explored the potential impact of large scale deployment of power plants with carbon capture technologies on future regional water stress in Europe. A database including 458 of European large

  12. Exploring the potential impact of implementing carbon capture technologies in fossil fuel power plants on regional European water stress index levels

    NARCIS (Netherlands)

    Schakel, W.B.; Pfister, Stephan; Ramirez, C.A.

    Equipping power plants with carbon capture technology can affect cooling demand and water use. This study has explored the potential impact of large scale deployment of power plants with carbon capture technologies on future regional water stress in Europe. A database including 458 of European

  13. Exploring the potential impact of implementing carbon capture technologies in fossil fuel power plants on regional European water stress index levels

    NARCIS (Netherlands)

    Schakel, W.B.; Pfister, Stephan; Ramirez, C.A.

    2015-01-01

    Equipping power plants with carbon capture technology can affect cooling demand and water use. This study has explored the potential impact of large scale deployment of power plants with carbon capture technologies on future regional water stress in Europe. A database including 458 of European large

  14. Bench-scale Development of an Advanced Solid Sorbent-based CO2 Capture Process for Coal-fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Thomas [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Kataria, Atish [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Soukri, Mustapha [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Farmer, Justin [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Mobley, Paul [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Tanthana, Jak [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Wang, Dongxiang [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Wang, Xiaoxing [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Song, Chunshan [Research Triangle Institute (RTI), Research Triangle Park, NC (United States)

    2015-12-31

    It is increasingly clear that CO2 capture and sequestration (CCS) must play a critical role in curbing worldwide CO2 emissions to the atmosphere. Development of these technologies to cost-effectively remove CO2 from coal-fired power plants is very important to mitigating the impact these power plants have within the world’s power generation portfolio. Currently, conventional CO2 capture technologies, such as aqueous-monoethanolamine based solvent systems, are prohibitively expensive and if implemented could result in a 75 to 100% increase in the cost of electricity for consumers worldwide. Solid sorbent CO2 capture processes – such as RTI’s Advanced Solid Sorbent CO2, Capture Process – are promising alternatives to conventional, liquid solvents. Supported amine sorbents – of the nature RTI has developed – are particularly attractive due to their high CO2 loadings, low heat capacities, reduced corrosivity/volatility and the potential to reduce the regeneration energy needed to carry out CO2 capture. Previous work in this area has failed to adequately address various technology challenges such as sorbent stability and regenerability, sorbent scale-up, improved physical strength and attrition-resistance, proper heat management and temperature control, proper solids handling and circulation control, as well as the proper coupling of process engineering advancements that are tailored for a promising sorbent technology. The remaining challenges for these sorbent processes have provided the framework for the project team’s research and development and target for advancing the technology beyond lab- and bench-scale testing. Under a cooperative agreement with the US Department of Energy, and part of NETL’s CO2 Capture Program, RTI has led an effort to address and mitigate the challenges associated with solid sorbent CO2 capture. The overall objective

  15. Improvement of dose distribution by central beam shielding in boron neutron capture therapy

    Science.gov (United States)

    Sakurai, Yoshinori; Ono, Koji

    2007-12-01

    Since boron neutron capture therapy (BNCT) with epithermal neutron beams started at the Kyoto University Reactor (KUR) in June 2002, nearly 200 BNCT treatments have been carried out. The epithermal neutron irradiation significantly improves the dose distribution, compared with the previous irradiation mainly using thermal neutrons. However, the treatable depth limit still remains. One effective technique to improve the limit is the central shield method. Simulations were performed for the incident neutron energies and the annular components of the neutron source. It was clear that thermal neutron flux distribution could be improved by decreasing the lower energy neutron component and the inner annular component of the incident beam. It was found that a central shield of 4-6 cm diameter and 10 mm thickness is effective for the 12 cm diameter irradiation field. In BNCT at KUR, the depth dose distribution can be much improved by the central shield method, resulting in a relative increase of the dose at 8 cm depth by about 30%. In addition to the depth dose distribution, the depth dose profile is also improved. As the dose rate in the central area is reduced by the additional shielding, the necessary irradiation time, however, increases by about 30% compared to normal treatment.

  16. Improved Vote Aggregation Techniques for the Geo-Wiki Cropland Capture Crowdsourcing Game

    Science.gov (United States)

    Baklanov, Artem; Fritz, Steffen; Khachay, Michael; Nurmukhametov, Oleg; Salk, Carl; See, Linda; Shchepashchenko, Dmitry

    2016-04-01

    Crowdsourcing is a new approach for solving data processing problems for which conventional methods appear to be inaccurate, expensive, or time-consuming. Nowadays, the development of new crowdsourcing techniques is mostly motivated by so called Big Data problems, including problems of assessment and clustering for large datasets obtained in aerospace imaging, remote sensing, and even in social network analysis. By involving volunteers from all over the world, the Geo-Wiki project tackles problems of environmental monitoring with applications to flood resilience, biomass data analysis and classification of land cover. For example, the Cropland Capture Game, which is a gamified version of Geo-Wiki, was developed to aid in the mapping of cultivated land, and was used to gather 4.5 million image classifications from the Earth's surface. More recently, the Picture Pile game, which is a more generalized version of Cropland Capture, aims to identify tree loss over time from pairs of very high resolution satellite images. Despite recent progress in image analysis, the solution to these problems is hard to automate since human experts still outperform the majority of machine learning algorithms and artificial systems in this field on certain image recognition tasks. The replacement of rare and expensive experts by a team of distributed volunteers seems to be promising, but this approach leads to challenging questions such as: how can individual opinions be aggregated optimally, how can confidence bounds be obtained, and how can the unreliability of volunteers be dealt with? In this paper, on the basis of several known machine learning techniques, we propose a technical approach to improve the overall performance of the majority voting decision rule used in the Cropland Capture Game. The proposed approach increases the estimated consistency with expert opinion from 77% to 86%.

  17. Low Cost Sorbent for Capturing CO2 Emissions Generated by Existing Coal-fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, Jeannine [TDA Research, Inc., Wheat Ridge, CO (United States)

    2013-08-31

    TDA Research, Inc. has developed a novel sorbent based post-combustion CO2 removal technology. This low cost sorbent can be regenerated with low-pressure (ca. 1 atm) superheated steam without temperature swing or pressure-swing. The isothermal and isobaric operation is a unique and advantageous feature of this process. The objective of this project was to demonstrate the technical and economic merit of this sorbent based CO2 capture approach. Through laboratory, bench-scale and field testing we demonstrated that this technology can effectively and efficiently capture CO2 produced at an existing pulverized coal power plants. TDA Research, Inc is developing both the solid sorbent and the process designed around that material. This project addresses the DOE Program Goal to develop a capture technology that can be added to an existing or new coal fired power plant, and can capture 90% of the CO2 produced with the lowest possible increase in the cost of energy. .

  18. Challenges and Improvements of Wind Power Dispatch in Northwest China

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Besides common characteristics of wind power, there are some special characteristics in China power system, including large-scale, long distance transmission and lack of flexible regulating power sources. These special characteristics make power dispatch more challenging in China. Many studies have been carried out and some improvements are presented including wind power monitoring and control as well as evaluation of wind power integration capabilities. As a demonstration project, the technologies are integrated into the energy management system and are implemented in the Northwest China power system. They provide effective measures for wind power dispatch in the grid.

  19. Development of a dynamic simulator for a natural gas combined cycle (NGCC) power plant with post-combustion carbon capture

    Energy Technology Data Exchange (ETDEWEB)

    Liese, E.; Zitney, S.

    2012-01-01

    The AVESTAR Center located at the U.S. Department of Energy’s National Energy Technology Laboratory and West Virginia University is a world-class research and training environment dedicated to using dynamic process simulation as a tool for advancing the safe, efficient and reliable operation of clean energy plants with CO{sub 2} capture. The AVESTAR Center was launched with a high-fidelity dynamic simulator for an Integrated Gasification Combined Cycle (IGCC) power plant with pre-combustion carbon capture. The IGCC dynamic simulator offers full-scope Operator Training Simulator (OTS) Human Machine Interface (HMI) graphics for realistic, real-time control room operation and is integrated with a 3D virtual Immersive Training Simulator (ITS), thus allowing joint control room and field operator training. The IGCC OTS/ITS solution combines a “gasification with CO{sub 2} capture” process simulator with a “combined cycle” power simulator into a single high-performance dynamic simulation framework. This presentation will describe progress on the development of a natural gas combined cycle (NGCC) dynamic simulator based on the syngas-fired combined cycle portion of AVESTAR’s IGCC dynamic simulator. The 574 MW gross NGCC power plant design consisting of two advanced F-class gas turbines, two heat recovery steam generators (HRSGs), and a steam turbine in a multi-shaft 2x2x1 configuration will be reviewed. Plans for integrating a post-combustion carbon capture system will also be discussed.

  20. Evaluating the impact of an ammonia-based post-combustion CO2 capture process on a steam power plant with different cooling water temperatures

    DEFF Research Database (Denmark)

    Linnenberg, Sebastian; Darde, Victor Camille Alfred; Oexmann, Jochen

    2012-01-01

    The use of aqueous ammonia is a promising option to capture carbon dioxide from the flue gas of coal-fired power plants. Compared to a capture process using monoethanolamine (MEA), the use of ammonia can reduce the heat requirement of the CO2 desorption significantly, although an additional effort...... is necessary to provide the cooling of the process. To allow for a fair evaluation of the integration of this CO2 capture process into a power plant process, an overall process evaluation is carried out. The use of detailed models of the power plant, of the compressor and of the CO2 capture process enables....... Additionally, two different process configurations of the capture plant, with either one single absorber or two absorbers connected in series where the first absorber captures the majority of the CO2 and the second limits the NH3 slip, are evaluated.The influence of the main process parameters (desorber...

  1. Improvement of power quality using distributed generation

    Energy Technology Data Exchange (ETDEWEB)

    Moreno-Munoz, A.; Lopez-Rodriguez, M.A.; Flores-Arias, J.M.; Bellido-Outerino, F.J. [Universidad de Cordoba, Departamento A.C., Electronica y T.E., Escuela Politecnica Superior, Campus de Rabanales, E-14071 Cordoba (Spain); de-la-Rosa, J.J.G. [Universidad de Cadiz, Area de Electronica, Dpto. ISA, TE y Electronica, Escuela Politecnica Superior Avda, Ramon Puyol, S/N, E-11202-Algeciras-Cadiz (Spain); Ruiz-de-Adana, M. [Universidad de Cordoba, Departamento de Quimica Fisica y Termodinamica Aplicada, Campus de Rabanales, E-14071 Cordoba (Spain)

    2010-12-15

    This paper addresses how Distributed Generation (DG), particularly when configured in Combined Heat and Power (CHP) mode, can become a powerful reliability solution in highlight automated factories, especially when integrated with complimentary Power Quality (PQ) measures. The paper presents results from the PQ audit conducted at a highly automated plant over last year. It was found that the main problems for the equipment installed were voltage sags. Among all categories of electrical disturbances, the voltage sag (dip) and momentary interruption are the nemeses of the automated industrial process. The paper analyzes the capabilities of modern electronic power supplies and the convenience of embedded solution. Finally it is addressed the role of the DG/CHP on the reliability of digital factories. (author)

  2. Comparative Assessment of Gasification Based Coal Power Plants with Various CO2 Capture Technologies Producing Electricity and Hydrogen

    Science.gov (United States)

    2014-01-01

    Seven different types of gasification-based coal conversion processes for producing mainly electricity and in some cases hydrogen (H2), with and without carbon dioxide (CO2) capture, were compared on a consistent basis through simulation studies. The flowsheet for each process was developed in a chemical process simulation tool “Aspen Plus”. The pressure swing adsorption (PSA), physical absorption (Selexol), and chemical looping combustion (CLC) technologies were separately analyzed for processes with CO2 capture. The performances of the above three capture technologies were compared with respect to energetic and exergetic efficiencies, and the level of CO2 emission. The effect of air separation unit (ASU) and gas turbine (GT) integration on the power output of all the CO2 capture cases is assessed. Sensitivity analysis was carried out for the CLC process (electricity-only case) to examine the effect of temperature and water-cooling of the air reactor on the overall efficiency of the process. The results show that, when only electricity production in considered, the case using CLC technology has an electrical efficiency 1.3% and 2.3% higher than the PSA and Selexol based cases, respectively. The CLC based process achieves an overall CO2 capture efficiency of 99.9% in contrast to 89.9% for PSA and 93.5% for Selexol based processes. The overall efficiency of the CLC case for combined electricity and H2 production is marginally higher (by 0.3%) than Selexol and lower (by 0.6%) than PSA cases. The integration between the ASU and GT units benefits all three technologies in terms of electrical efficiency. Furthermore, our results suggest that it is favorable to operate the air reactor of the CLC process at higher temperatures with excess air supply in order to achieve higher power efficiency. PMID:24578590

  3. Comparative Assessment of Gasification Based Coal Power Plants with Various CO2 Capture Technologies Producing Electricity and Hydrogen.

    Science.gov (United States)

    Mukherjee, Sanjay; Kumar, Prashant; Hosseini, Ali; Yang, Aidong; Fennell, Paul

    2014-02-20

    Seven different types of gasification-based coal conversion processes for producing mainly electricity and in some cases hydrogen (H2), with and without carbon dioxide (CO2) capture, were compared on a consistent basis through simulation studies. The flowsheet for each process was developed in a chemical process simulation tool "Aspen Plus". The pressure swing adsorption (PSA), physical absorption (Selexol), and chemical looping combustion (CLC) technologies were separately analyzed for processes with CO2 capture. The performances of the above three capture technologies were compared with respect to energetic and exergetic efficiencies, and the level of CO2 emission. The effect of air separation unit (ASU) and gas turbine (GT) integration on the power output of all the CO2 capture cases is assessed. Sensitivity analysis was carried out for the CLC process (electricity-only case) to examine the effect of temperature and water-cooling of the air reactor on the overall efficiency of the process. The results show that, when only electricity production in considered, the case using CLC technology has an electrical efficiency 1.3% and 2.3% higher than the PSA and Selexol based cases, respectively. The CLC based process achieves an overall CO2 capture efficiency of 99.9% in contrast to 89.9% for PSA and 93.5% for Selexol based processes. The overall efficiency of the CLC case for combined electricity and H2 production is marginally higher (by 0.3%) than Selexol and lower (by 0.6%) than PSA cases. The integration between the ASU and GT units benefits all three technologies in terms of electrical efficiency. Furthermore, our results suggest that it is favorable to operate the air reactor of the CLC process at higher temperatures with excess air supply in order to achieve higher power efficiency.

  4. Power turbine bypass for improved compression braking

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, R.M.; Lutz, T.P.; Stang, J.

    1992-06-09

    This patent describes a turbocompound engine having a power turbine bypass control. It comprises an internal combustion engine having a crankshaft, an intake manifold and an exhaust manifold; turbocharger means connected with the intake and exhaust manifolds for converting exhaust gas energy into mechanical energy for boosting intake air pressure; power turbine means for producing mechanical energy from energy remaining in the exhaust gases exiting the first turbine.

  5. Energetic evaluation of a power plant integrated with a piperazine-based CO2 capture process

    NARCIS (Netherlands)

    Kvamsdal, H.M.; Romano, M.C.; Ham, L.V. van der; Bonalumi, D.; Os, P.J. van; Goetheer, E.L.V.

    2014-01-01

    Extensive research efforts have been applied to obtain more efficient and less cost-intensive absorption-based processes and solvent systems for CO2capture during the last 15–20 years. High concentratedaqueous solutions of piperazine (PZ) have been suggested as a good replacement for the current ben

  6. Energetic evaluation of a power plant integrated with a piperazine-based CO2 capture process

    NARCIS (Netherlands)

    Kvamsdal, H.M.; Romano, M.C.; Ham, L.V. van der; Bonalumi, D.; Os, P.J. van; Goetheer, E.L.V.

    2014-01-01

    Extensive research efforts have been applied to obtain more efficient and less cost-intensive absorption-based processes and solvent systems for CO2capture during the last 15–20 years. High concentratedaqueous solutions of piperazine (PZ) have been suggested as a good replacement for the current

  7. Improving transition between power optimization and power limitation of variable speed/variable pitch wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, A.D.; Bindner, H. [Risoe National Lab., Wind Energy and Atmospheric Physics Dept., Roskilde (Denmark); Rebsdorf, A. [Vestas Wind Systems A/S, Lem (Denmark)

    1999-03-01

    The paper summarises and describes the main results of a recently performed study of improving the transition between power optimization and power limitation for variable speed/variable pitch wind turbines. The results show that the capability of varying the generator speed also can be exploited in the transition stage to improve the quality of the generated power. (au)

  8. A speed-optimized RGB-Z capture system with improved denoising capabilities

    Science.gov (United States)

    Chuchvara, Aleksandra; Georgiev, Mihail; Gotchev, Atanas

    2014-02-01

    We have developed an end-to-end system for 3D scene sensing which combines a conventional high-resolution RGB camera with a low-resolution Time-of-Flight (ToF) range sensor. The system comprises modules for range data denoising, data re-projection and non-uniform to uniform up-sampling and aims at composing high-resolution 3D video output for driving auto-stereoscopic 3D displays in real-time. In our approach, the ToF sensor is set to work with short integration time with the aim to increase the capture speed and decrease the amount of motion artifacts. However, reduced integration time leads to noisy range images. We specifically address the noise reduction problem by performing a modification of the non-local means filtering in spatio-temporal domain. Time-consecutive range images are utilized not only for efficient de-noising but also for accurate non-uniform to uniform up-sampling on the high-resolution RGB grid. Use is made of the reflectance signal of the ToF sensor for providing a confidence-type of feedback to the denosing module where a new adaptive averaging is proposed to effectively handle motion artifacts. As of the non-uniform to uniform resampling of range data is concerned, we have developed two alternative solutions; one relying entirely on the GPU power and another being applicable to any general platform. The latter method employs an intermediate virtual range camera recentering after with the resamploing process degrades to a 2D interpolation performed within the lowresolution grid. We demonstrate a real-time performance of the system working in low-power regime.

  9. Improved repowering techniques for power plants

    DEFF Research Database (Denmark)

    Houbak, Niels; Andersen, Simon E.; Petersen, Stiig Bo

    1998-01-01

    Repowering of existing coal-fired power plants is often accomplished by adding gas turbines. In this paper we assume that the gas turbine exhaust is used for feed water preheating.Typical gas turbine exhaust temperatures are in the range 450-600C whereas typical boiler inlet temperatures are 250......-300C. The big difference in temperature between exhaust and water prevents an efficient exchange of heat. One way to lower the exhaust temperature is to expand the gas to sub atmospheric pressure. The result is a 50% increase in possible installed gas turbine power....

  10. Computer-assisted design of imidazolate-based ionic liquids for improving SO2 capture, CO2 capture, and SO2/CO2 selectivity.

    Science.gov (United States)

    Cui, Guokai; Zhao, Ning; Wang, Jianji; Wang, Congmin

    2017-08-24

    A new strategy using computer-assisted design of substituted imidazolate-based ionic liquids (ILs) through tuning the absorption enthalpy as well as the basicity of ILs for improving SO2 capture, CO2 capture, and SO2/CO2 selectivity was reported. The best substituted imidazolate-based ILs as absorbents for different applications were predicted at first. During the absorption, a high SO2 capacity up to 5.28 and 2.38 mole SO2 per mole IL could be achieved by ILs with CH3-imidazolate anion under 1.0 and 0.1 bar, respectively, through tuning multiple N∙∙∙S interactions between SO2 and N atoms in the imidazolate anion with different substituent. In addition, CO2 capture by imidazolate-based ILs could also be easily tuned through changing the substitute of ILs, and Br-imidazolate IL showed the high CO2 capacity but low absorption enthalpy. Furthermore, the high selectivity for SO2/CO2 could be reached by imidazolate-based ILs with CN-imidazolate anion due to their high SO2 capacity but low CO2 capacity. The results put forward in this work are in good agreement with the prediction. Quantum chemical calculations, FT-IR and NMR analysis methods were used to discuss SO2 and CO2 absorption mechanism. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Assessment of power reliability and improvement potential by using ...

    African Journals Online (AJOL)

    Assessment of power reliability and improvement potential by using smart reclosers. ... Electric reliability has affected social well being, public health, water supply, ... of smart reclosers improves the reliability of the distribution network by 75% ...

  12. A Method to Capture Macroslip at Bolted Interfaces [PowerPoint

    Energy Technology Data Exchange (ETDEWEB)

    Hopkins, Ronald Neil; Heitman, Lili Anne Akin

    2016-01-01

    Relative motion at bolted connections can occur for large shock loads as the internal shear force in the bolted connection overcomes the frictional resistive force. This macroslip in a structure dissipates energy and reduces the response of the components above the bolted connection. There is a need to be able to capture macroslip behavior in a structural dynamics model. A linear model and many nonlinear models are not able to predict marcoslip effectively. The proposed method to capture macroslip is to use the multi-body dynamics code ADAMS to model joints with 3-D contact at the bolted interfaces. This model includes both static and dynamic friction. The joints are preloaded and the pinning effect when a bolt shank impacts a through hole inside diameter is captured. Substructure representations of the components are included to account for component flexibility and dynamics. This method was applied to a simplified model of an aerospace structure and validation experiments were performed to test the adequacy of the method.

  13. Conventional Exergetic and Exergoeconomic Analyses of a Power Plant with Chemical Looping Combustion for CO2 Capture

    Directory of Open Access Journals (Sweden)

    Tatiana Morosuk

    2010-09-01

    Full Text Available

    Exergy-based methods can be used as a tool for examining, comparing and assessing thermodynamic systems. In this paper, an exergoeconomic analysis is used to evaluate a power plant with chemical looping combustion (CLC for CO2 capture. This oxy-fuel plant is compared, from an exergetic and an economic perspective, to a conventional, reference power plant without CO2 capture. The exergetic analysis shows decreased exergy destruction in the CLC reactors, compared to the exergy destruction in the conventional combustion chamber of the reference case; thus, the irreversibilities caused by combustion in the CLC are reduced. However, due to the addition of the CO2 compression unit, the overall exergetic efficiency of the plant with CLC is lower than that of the reference plant by approximately 5 percentage points. The economic analysis confirms a significant increase in the investment cost of the CO2 capture plant, due to the addition of the units for CO2 compression and CLC. Thus, the cost of electricity is 24% higher for this plant in comparison to that of the reference case. Nevertheless, when compared to the reference plant with CO2 capture with monoethanolamine, the plant with CLC was found to be a more economical option. Since CO2 abatement must be realized in the future, given expected environmental or tax measures, CLC provides relatively low cost carbon dioxide capture and it, therefore, appears to be a promising option for

  14. CO2 Fixation, Lipid Production, and Power Generation by a Novel Air-Lift-Type Microbial Carbon Capture Cell System.

    Science.gov (United States)

    Hu, Xia; Liu, Baojun; Zhou, Jiti; Jin, Ruofei; Qiao, Sen; Liu, Guangfei

    2015-09-01

    An air-lift-type microbial carbon capture cell (ALMCC) was constructed for the first time by using an air-lift-type photobioreactor as the cathode chamber. The performance of ALMCC in fixing high concentration of CO2, producing energy (power and biodiesel), and removing COD together with nutrients was investigated and compared with the traditional microbial carbon capture cell (MCC) and air-lift-type photobioreactor (ALP). The ALMCC system produced a maximum power density of 972.5 mW·m(-3) and removed 86.69% of COD, 70.52% of ammonium nitrogen, and 69.24% of phosphorus, which indicate that ALMCC performed better than MCC in terms of power generation and wastewater treatment efficiency. Besides, ALMCC demonstrated 9.98- and 1.88-fold increases over ALP and MCC in the CO2 fixation rate, respectively. Similarly, the ALMCC significantly presented a higher lipid productivity compared to those control reactors. More importantly, the preliminary analysis of energy balance suggested that the net energy of the ALMCC system was significantly superior to other systems and could theoretically produce enough energy to cover its consumption. In this work, the established ALMCC system simultaneously achieved the high level of CO2 fixation, energy recycle, and municipal wastewater treatment effectively and efficiently.

  15. Predicting the ultimate potential of natural gas SOFC power cycles with CO2 capture - Part A: Methodology and reference cases

    Science.gov (United States)

    Campanari, Stefano; Mastropasqua, Luca; Gazzani, Matteo; Chiesa, Paolo; Romano, Matteo C.

    2016-08-01

    Driven by the search for the highest theoretical efficiency, in the latest years several studies investigated the integration of high temperature fuel cells in natural gas fired power plants, where fuel cells are integrated with simple or modified Brayton cycles and/or with additional bottoming cycles, and CO2 can be separated via chemical or physical separation, oxy-combustion and cryogenic methods. Focusing on Solid Oxide Fuel Cells (SOFC) and following a comprehensive review and analysis of possible plant configurations, this work investigates their theoretical potential efficiency and proposes two ultra-high efficiency plant configurations based on advanced intermediate-temperature SOFCs integrated with a steam turbine or gas turbine cycle. The SOFC works at atmospheric or pressurized conditions and the resulting power plant exceeds 78% LHV efficiency without CO2 capture (as discussed in part A of the work) and 70% LHV efficiency with substantial CO2 capture (part B). The power plants are simulated at the 100 MW scale with a complete set of realistic assumptions about fuel cell (FC) performance, plant components and auxiliaries, presenting detailed energy and material balances together with a second law analysis.

  16. Coal Direct Chemical Looping Retrofit to Pulverized Coal Power Plants for In-Situ CO2 Capture

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Liang; Li, Fanxing; Kim, Ray; Bayham, Samuel; McGiveron, Omar; Tong, Andrew; Connell, Daniel; Luo, Siwei; Sridhar, Deepak; Wang, Fei; Sun, Zhenchao; Fan, Liang-Shih

    2013-09-30

    A novel Coal Direct Chemical Looping (CDCL) system is proposed to effectively capture CO2 from existing PC power plants. The work during the past three years has led to an oxygen carrier particle with satisfactory performance. Moreover, successful laboratory, bench scale, and integrated demonstrations have been performed. The proposed project further advanced the novel CDCL technology to sub-pilot scale (25 kWth). To be more specific, the following objectives attained in the proposed project are: 1. to further improve the oxygen carrying capacity as well as the sulfur/ash tolerance of the current (working) particle; 2. to demonstrate continuous CDCL operations in an integrated mode with > 99% coal (bituminous, subbituminous, and lignite) conversion as well as the production of high temperature exhaust gas stream that is suitable for steam generation in existing PC boilers; 3. to identify, via demonstrations, the fate of sulfur and NOx; 4. to conduct thorough techno-economic analysis that validates the technical and economical attractiveness of the CDCL system. The objectives outlined above were achieved through collaborative efforts among all the participants. CONSOL Energy Inc. performed the techno-economic analysis of the CDCL process. Shell/CRI was able to perform feasibility and economic studies on the large scale particle synthesis and provide composite particles for the sub-pilot scale testing. The experience of B&W (with boilers) and Air Products (with handling gases) assisted the retrofit system design as well as the demonstration unit operations. The experience gained from the sub-pilot scale demonstration of the Syngas Chemical Looping (SCL) process at OSU was able to ensure the successful handling of the solids. Phase 1 focused on studies to improve the current particle to better suit the CDCL operations. The optimum operating conditions for the reducer reactor such as the temperature, char gasification enhancer type, and flow rate were identified. The

  17. Advances in Model-Based Design of Flexible and Prompt Energy Systems -- The CO2 Capture Plant at the Buggenum IGCC Power Station as a Test Case

    NARCIS (Netherlands)

    Trapp, C.

    2014-01-01

    Pre-combustion CO2 capture applied to integrated gasification combined cycle (IGCC) power plants is a promising technical solution to reduce CO2 emissions due to fossil-fuelled electricity generation in order to meet environmental targets in a carbon-constrained future. The pre-combustion capture

  18. Advances in Model-Based Design of Flexible and Prompt Energy Systems -- The CO2 Capture Plant at the Buggenum IGCC Power Station as a Test Case

    NARCIS (Netherlands)

    Trapp, C.

    2014-01-01

    Pre-combustion CO2 capture applied to integrated gasification combined cycle (IGCC) power plants is a promising technical solution to reduce CO2 emissions due to fossil-fuelled electricity generation in order to meet environmental targets in a carbon-constrained future. The pre-combustion capture pr

  19. Active power line conditioners design, simulation and implementation for improving power quality

    CERN Document Server

    Revuelta, Patricio Salmeron; Litrán, Salvador Pérez

    2015-01-01

    Active Power Line Conditioners: Design, Simulation and Implementation for Improving Power Quality presents a rigorous theoretical and practical approach to active power line conditioners, one of the subjects of most interest in the field of power quality. Its broad approach offers a journey that will allow power engineering professionals, researchers, and graduate students to learn more about the latest landmarks on the different APLC configurations for load active compensation. By introducing the issues and equipment needs that arise when correcting the lack of power quality in power grids

  20. Beyond Standardization: Powerful New Principles for Improvement

    Science.gov (United States)

    Hargreaves, Andy; Shirley, Dennis

    2008-01-01

    Almost all of the most recent school improvement strategies have focused on standards and accountability. But test data from assessments such as the National Assessment of Educational Progress indicate that such emphasis has had little impact on student achievement. Drawing from extensive research across national settings, Andy Hargreaves and…

  1. Networks as Power Bases for School Improvement

    Science.gov (United States)

    Moore, Tessa A.; Kelly, Michael P.

    2009-01-01

    Although there is limited research into the success of primary school networking initiatives in the UK, there is a drive at national government level for promoting school collaborative working arrangements as a catalyst for whole-school improvement. This paper discusses the findings from research into two such initiatives: "Networked Learning…

  2. Improving acceptance in wind power planning

    Energy Technology Data Exchange (ETDEWEB)

    Hammarlund, K. [Lund Univ. (Sweden). Dept. of Social and Economic Geography

    1996-12-01

    This paper presents important factors and planning procedures for public acceptance of wind power. Opinion surveys in Sweden show that acceptance is connected to the concept of utility rather than the aesthetic values. If wind turbines are confined by the authorities to marginal areas, they will not earn their rightful place in the landscape by being of use. A positive attitude in general promotes a positive experience of the effects of wind turbines. It is therefore essential to establish a sense of cooperation between the project management and the public. An open dialogue and continuous information will increase the possibilities for acceptance of future development. We must establish new codes of practice in permit processing because policies today contains ideological and practical contradictions between development and preservation of landscapes. 16 refs, 2 tabs

  3. Viability of Carbon Capture and Sequestration Retrofits for Existing Coal-Fired Power Plants under an Emission Trading Scheme.

    Science.gov (United States)

    Talati, Shuchi; Zhai, Haibo; Morgan, M Granger

    2016-12-06

    Using data on the coal-fired electric generating units (EGUs) in Texas we assess the economic feasibility of retrofitting existing units with carbon capture and sequestration (CCS) in order to comply with the Clean Power Plan's rate-based emission standards under an emission trading scheme. CCS with 90% capture is shown to be more economically attractive for a range of existing units than purchasing emission rate credits (ERCs) from a trading market at an average credit price above $28 per MWh under the final state standard and $35 per MWh under the final national standard. The breakeven ERC trading prices would decrease significantly if the captured CO2 were sold for use in enhanced oil recovery, making CCS retrofits viable at lower trading prices. The combination of ERC trading and CO2 use can greatly reinforce economic incentives and market demands for CCS and hence accelerate large-scale deployment, even under scenarios with high retrofit costs. Comparing the levelized costs of electricity generation between CCS retrofits and new renewable plants under the ERC trading scheme, retrofitting coal-fired EGUs with CCS may be significantly cheaper than new solar plants under some market conditions.

  4. Utilizing Climate Forecasts for Improving Water and Power Systems Coordination

    Science.gov (United States)

    Arumugam, S.; Queiroz, A.; Patskoski, J.; Mahinthakumar, K.; DeCarolis, J.

    2016-12-01

    Climate forecasts, typically monthly-to-seasonal precipitation forecasts, are commonly used to develop streamflow forecasts for improving reservoir management. Irrespective of their high skill in forecasting, temperature forecasts in developing power demand forecasts are not often considered along with streamflow forecasts for improving water and power systems coordination. In this study, we consider a prototype system to analyze the utility of climate forecasts, both precipitation and temperature, for improving water and power systems coordination. The prototype system, a unit-commitment model that schedules power generation from various sources, is considered and its performance is compared with an energy system model having an equivalent reservoir representation. Different skill sets of streamflow forecasts and power demand forecasts are forced on both water and power systems representations for understanding the level of model complexity required for utilizing monthly-to-seasonal climate forecasts to improve coordination between these two systems. The analyses also identify various decision-making strategies - forward purchasing of fuel stocks, scheduled maintenance of various power systems and tradeoff on water appropriation between hydropower and other uses - in the context of various water and power systems configurations. Potential application of such analyses for integrating large power systems with multiple river basins is also discussed.

  5. Storage and recovery of elastic potential energy powers ballistic prey capture in toads.

    Science.gov (United States)

    Lappin, A Kristopher; Monroy, Jenna A; Pilarski, Jason Q; Zepnewski, Eric D; Pierotti, David J; Nishikawa, Kiisa C

    2006-07-01

    Ballistic tongue projection in toads is a remarkably fast and powerful movement. The goals of this study were to: (1) quantify in vivo power output and activity of the depressor mandibulae muscles that are responsible for ballistic mouth opening, which powers tongue projection; (2) quantify the elastic properties of the depressor mandibulae muscles and their series connective tissues using in situ muscle stimulation and force-lever studies; and (3) develop and test an elastic recoil model, based on the observed elastic properties of the depressor mandibulae muscles and series connective tissues, that accounts for displacement, velocity, acceleration and power output during ballistic mouth opening in toads. The results demonstrate that the depressor mandibulae muscles of toads are active for up to 250 ms prior to mouth opening. During this time, strains of up to 21.4% muscle resting length (ML) develop in the muscles and series connective tissues. At maximum isometric force, series connective tissues develop strains up to 14% ML, and the muscle itself develops strains up to 17.5% ML. When the mouth opens rapidly, the peak instantaneous power output of the depressor mandibulae muscles and series connective tissues can reach 9600 W kg(-1). The results suggest that: (1) elastic recoil of muscle itself can contribute significantly to the power of ballistic movements; (2) strain in series elastic elements of the depressor mandibulae muscle is too large to be borne entirely by the cross bridges and the actin-myosin filament lattice; and (3) central nervous control of ballistic tongue projection in toads likely requires the specification of relatively few parameters.

  6. Higher powered magnification improved endodontic surgery outcomes.

    Science.gov (United States)

    Levenson, David

    2012-01-01

    Medline, Embase and PubMed databases were searched together with hand-searches of a range of journals (Journal of Endodontics, International Endodontic Journal, Oral Surgery Oral Medicine Oral Pathology Oral Radiology and Endodontics, Journal of Oral and Maxillofacial Surgery, International Journal of Oral and Maxillofacial Surgery). Clinical studies in several languages (English, French, German, Italian and Spanish) with a minimum follow-up of six months evaluated using clinical and radiographic examination included. Assessment and data abstraction were carried out independently. Weighted pooled success rates and relative risk assessment between TRS and EMS were calculated and a meta-analysis was carried out using a random effects model. Fourteen studies met the inclusion criteria. Weighted pooled success rates calculated from extracted raw data showed an 88% positive outcome for CRS (95% confidence interval [CI], 0.8455-0.9164) and 94% for EMS (95% CI, 0.8889-0.9816). This difference was statistically significant (P < .0005). Relative risk ratio analysis showed that the probability of success for EMS was 1.07 times that for CRS. Seven studies provided information on the individual tooth type. The probability of success between the groups was statistically significant in favour of EMS for molars, but no significant difference was found for anteriors or premolars. The probability for success for EMS proved to be significantly greater than the probability for success for CRS, providing best available evidence on the influence of high-power magnification rendered by the dental operating microscope or the endoscope.

  7. Modularity and rates of evolutionary change in a power-amplified prey capture system.

    Science.gov (United States)

    Claverie, Thomas; Patek, S N

    2013-11-01

    The dynamic interplay among structure, function, and phylogeny form a classic triad of influences on the patterns and processes of biological diversification. Although these dynamics are widely recognized as important, quantitative analyses of their interactions have infrequently been applied to biomechanical systems. Here we analyze these factors using a fundamental biomechanical mechanism: power amplification. Power-amplified systems use springs and latches to generate extremely fast and powerful movements. This study focuses specifically on the power amplification mechanism in the fast raptorial appendages of mantis shrimp (Crustacea: Stomatopoda). Using geometric morphometric and phylogenetic comparative analyses, we measured evolutionary modularity and rates of morphological evolution of the raptorial appendage's biomechanical components. We found that "smashers" (hammer-shaped raptorial appendages) exhibit lower modularity and 10-fold slower rates of morphological change when compared to non-smashers (spear-shaped or undifferentiated appendages). The morphological and biomechanical integration of this system at a macroevolutionary scale and the presence of variable rates of evolution reveal a balance between structural constraints, functional variation, and the "roles of development and genetics" in evolutionary diversification. © 2013 The Author(s). Evolution © 2013 The Society for the Study of Evolution.

  8. Improvement of Main Magnetic Field Power Supply of SFC

    Institute of Scientific and Technical Information of China (English)

    ZhangXianlai; YanHuaihai; XinJunye; ZhangShu

    2003-01-01

    The main magnetic field power supply is used for establishing main magnetic field of SFC, therefore excellent current stability and low ripple are required. Its DC output current range is 0~1300 A and max output voltage is 230 V. The power supply has been put into operation since Sep. in 2000, and was replaced in 033 room from 166 room of No.2 Building. We have improved the performance of power supply in this period.

  9. Improving Power System Transient Stability with Static Synchronous Series Compensator

    Directory of Open Access Journals (Sweden)

    Prechanon Kumkratug

    2011-01-01

    Full Text Available Problem statement: Modern power system consists of the complicated network of transmission lines and carries heavy demand. Thus they cause in the stability problem. One of the major interests of power utilities is the improvement of power system transient behavior. Approach: Static Synchronous Series Compensator (SSSC is a power electronic based device that has the capability of controlling the power flow through a line. This study applies the SSSC to improve transient stability of power system. To verify the effect of the SSSC on transient stability, the mathematical model and control strategy of a SSSC is presented. The SSSC is represented by variable voltage injection with associate transformer leakage reactance and the voltage source. The series voltage injection model of SSSC is modeled into power flow equation and thus it is used to determine its control strategy. This study uses machine speed deviation to control it. The swing curves of the three phase faulted power system without and with a SSSC is tested and compared in various cases. Results: The swing curve of system without a SSSC gets increases monotonically and thus the system can be considered as unstable whereas the swing curves of system with a SSSC can be considered as stable. Conclusion: SSSSC can improve transient stability of power system.

  10. Power margin improvement for OFDMA-PON using hierarchical modulation.

    Science.gov (United States)

    Cao, Pan; Hu, Xiaofeng; Zhuang, Zhiming; Zhang, Liang; Chang, Qingjiang; Yang, Qi; Hu, Rong; Su, Yikai

    2013-04-08

    We propose and experimentally demonstrate a hierarchical modulation scheme to improve power margin for orthogonal frequency division multiple access-passive optical networks (OFDMA-PONs). In a PON system, under the same launched optical power, optical network units (ONUs) have different power margins due to unequal distribution fiber lengths. The power margin of the PON system is determined by the ONU with the lowest power margin. In our proposed scheme, ONUs with long and short distribution fibers are grouped together, and downstream signals for the paired ONUs are mapped onto the same OFDM subcarriers using hierarchical modulation. In a pair of ONUs, part of the power margin of the ONU with short distribution fiber is re-allocated to the ONU with long distribution fiber. Therefore, the power margin of the ONU with the longest distribution fiber can be increased, leading to the power margin improvement of the PON system. Experimental results show that the hierarchical modulation scheme improves the power margin by 2.7 dB for an OFDMA-PON system, which can be used to support more users or extend transmission distance.

  11. Slipstream pilot-scale demonstration of a novel amine-based post-combustion technology for carbon dioxide capture from coal-fired power plant flue gas

    Energy Technology Data Exchange (ETDEWEB)

    Krishnamurthy, Krish R. [Linde LLC, Murray Hill, NJ (United States)

    2017-02-03

    Post-combustion CO2 capture (PCC) technology offers flexibility to treat the flue gas from both existing and new coal-fired power plants and can be applied to treat all or a portion of the flue gas. Solvent-based technologies are today the leading option for PCC from commercial coal-fired power plants as they have been applied in large-scale in other applications. Linde and BASF have been working together to develop and further improve a PCC process incorporating BASF’s novel aqueous amine-based solvent technology. This technology offers significant benefits compared to other solvent-based processes as it aims to reduce the regeneration energy requirements using novel solvents that are very stable under the coal-fired power plant feed gas conditions. BASF has developed the desired solvent based on the evaluation of a large number of candidates. In addition, long-term small pilot-scale testing of the BASF solvent has been performed on a lignite-fired flue gas. In coordination with BASF, Linde has evaluated a number of options for capital cost reduction in large engineered systems for solvent-based PCC technology. This report provides a summary of the work performed and results from a project supported by the US DOE (DE-FE0007453) for the pilot-scale demonstration of a Linde-BASF PCC technology using coal-fired power plant flue gas at a 1-1.5 MWe scale in Wilsonville, AL at the National Carbon Capture Center (NCCC). Following a project kick-off meeting in November 2011 and the conclusion of pilot plant design and engineering in February 2013, mechanical completion of the pilot plant was achieved in July 2014, and final commissioning activities were completed to enable start-up of operations in January 2015. Parametric tests were performed from January to December 2015 to determine optimal test conditions and evaluate process performance over a variety of operation parameters. A long-duration 1500-hour continuous test campaign was performed from May to

  12. Capturing Dynamics in the Power Grid: Formulation of Dynamic State Estimation through Data Assimilation

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Ning [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Huang, Zhenyu [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Meng, Da [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Elbert, Stephen T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Shaobu [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Diao, Ruisheng [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-03-31

    With the increasing complexity resulting from uncertainties and stochastic variations introduced by intermittent renewable energy sources, responsive loads, mobile consumption of plug-in vehicles, and new market designs, more and more dynamic behaviors are observed in everyday power system operation. To operate a power system efficiently and reliably, it is critical to adopt a dynamic paradigm so that effective control actions can be taken in time. The dynamic paradigm needs to include three fundamental components: dynamic state estimation; look-ahead dynamic simulation; and dynamic contingency analysis (Figure 1). These three components answer three basic questions: where the system is; where the system is going; and how secure the system is against accidents. The dynamic state estimation provides a solid cornerstone to support the other 2 components and is the focus of this study.

  13. VOLTAGE STABILITY IMPROVEMENT IN POWER SYSTEM BY USING STATCOM

    Directory of Open Access Journals (Sweden)

    A.ANBARASAN

    2012-11-01

    Full Text Available Voltage stability problems usually occur in heavily loaded systems. Nowadays the power demand increases enormously, hence in a large interconnected power system network subject to stress conditions. This situation can be handled by increasing the generation or reducing the transmission losses. When the load increases suddenly, voltage magnitude also varies beyond the permissible voltage stability limit. But the voltage magnitude must be maintained within the limit for proper operation of the system. Hence, voltage stability must be improved by providing suitable reactive power compensation. The proposed work was analyzed using IEEE 14 bus test system. The STATCOM improves the voltage stability margin of the system.

  14. Two Sudden Onsets Capture Attention but Do Not Improve Visual Short-Term Memory

    Directory of Open Access Journals (Sweden)

    Huang Chi-Hsiang

    2011-05-01

    Full Text Available Onset stimulus can capture attention and then transfer into visual short-term memory. It remains unknown whether two sudden onsets also capture attention and are stored in vSTM. We modified Belopolsky, Kramer, and Godijn's (2008 visual search paradigm to test this issue. Experiment 1 using one onset and replicated Belopolsky et al's results. Two onsets in Experiment 2 were found to capture attention; however, recognition performance for the onsets was only at chance level, showing poor memory. Experiment 3 used a retro-cue to test whether only one of these two onsets can be stored in vSTM. Experiment 4 tested whehter this poor recognition was caused by interference from meory probe. This study has important insights on how attention interacts with memory.

  15. Research and development of CO2 Capture and Storage Technologies in Fossil Fuel Power Plants

    Directory of Open Access Journals (Sweden)

    Lukáš Pilař

    2012-01-01

    Full Text Available This paper presents the results of a research project on the suitability of post-combustion CCS technology in the Czech Republic. It describes the ammonia CO2 separation method and its advantages and disadvantages. The paper evaluates its impact on the recent technology of a 250 MWe lignite coal fired power plant. The main result is a decrease in electric efficiency by 11 percentage points, a decrease in net electricity production by 62 MWe, and an increase in the amount of waste water. In addition, more consumables are needed.

  16. Optimal control system design of an acid gas removal unit for an IGCC power plants with CO2 capture

    Energy Technology Data Exchange (ETDEWEB)

    Jones, D.; Bhattacharyya, D.; Turton, R.; Zitney, S.

    2012-01-01

    Future IGCC plants with CO{sub 2} capture should be operated optimally in the face of disturbances without violating operational and environmental constraints. To achieve this goal, a systematic approach is taken in this work to design the control system of a selective, dual-stage Selexol-based acid gas removal (AGR) unit for a commercial-scale integrated gasification combined cycle (IGCC) power plant with pre-combustion CO{sub 2} capture. The control system design is performed in two stages with the objective of minimizing the auxiliary power while satisfying operational and environmental constraints in the presence of measured and unmeasured disturbances. In the first stage of the control system design, a top-down analysis is used to analyze degrees of freedom, define an operational objective, identify important disturbances and operational/environmental constraints, and select the control variables. With the degrees of freedom, the process is optimized with relation to the operational objective at nominal operation as well as under the disturbances identified. Operational and environmental constraints active at all operations are chosen as control variables. From the results of the optimization studies, self-optimizing control variables are identified for further examination. Several methods are explored in this work for the selection of these self-optimizing control variables. Modifications made to the existing methods will be discussed in this presentation. Due to the very large number of candidate sets available for control variables and due to the complexity of the underlying optimization problem, solution of this problem is computationally expensive. For reducing the computation time, parallel computing is performed using the Distributed Computing Server (DCS®) and the Parallel Computing® toolbox from Mathworks®. The second stage is a bottom-up design of the control layers used for the operation of the process. First, the regulatory control layer is

  17. Power quality improvement of unbalanced power system with distributed generation units

    DEFF Research Database (Denmark)

    Hu, Y.; Chen, Zhe; Excell, P.

    2011-01-01

    This paper presents a power electronic system for improving the power quality of the unbalanced distributed generation units in three-phase four-wire system. In the system, small renewable power generation units, such as small PV generator, small wind turbines may be configured as single phase...... generation units. The random nature of renewable power sources may result in significant unbalance in the power network and affect the power quality. An electronic converter system is proposed to correct the system unbalance and harmonics so as to deal with the power quality problems. The operation...... and control of the converter are described. Simulation results have demonstrated that the system can effectively correct the unbalance and enhance the system power quality....

  18. Potential impacts of electric power production utilizing natural gas, renewables and carbon capture and sequestration on US Freshwater resources.

    Science.gov (United States)

    Tidwell, Vincent C; Malczynski, Leonard A; Kobos, Peter H; Klise, Geoffrey T; Shuster, Erik

    2013-08-06

    Carbon capture and sequestration (CCS) has important implications relative to future thermoelectric water use. A bounding analysis is performed using past greenhouse gas emission policy proposals and assumes either all effected capacity retires (lower water use bound) or is retrofitted (upper bound). The analysis is performed in the context of recent trends in electric power generation expansion, namely high penetration of natural gas and renewables along with constrained cooling system options. Results indicate thermoelectric freshwater withdrawals nationwide could increase by roughly 1% or decrease by up to 60% relative to 2009 levels, while consumption could increase as much as 21% or decrease as much as 28%. To identify where changes in freshwater use might be problematic at a regional level, electric power production has been mapped onto watersheds with limited water availability (where consumption exceeds 70% of gauged streamflow). Results suggest that between 0.44 and 0.96 Mm(3)/d of new thermoelectric freshwater consumption could occur in watersheds with limited water availability, while power plant retirements in these watersheds could yield 0.90 to 1.0 Mm(3)/d of water savings.

  19. Improving Free-Piston Stirling Engine Power Density

    Science.gov (United States)

    Briggs, Maxwell H.

    2016-01-01

    Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58% using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a maximum piston power increase of 14%. Analytical predictions are compared to experimental data showing close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

  20. Improving Power Density of Free-Piston Stirling Engines

    Science.gov (United States)

    Briggs, Maxwell H.; Prahl, Joseph M.; Loparo, Kenneth A.

    2016-01-01

    Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free-piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58 percent using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a piston power increase of as much as 14 percent. Analytical predictions are compared to experimental data and show close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

  1. Improved method for bacterial cell capture after flow cytometry cell sorting.

    Science.gov (United States)

    Guillebault, D; Laghdass, M; Catala, P; Obernosterer, I; Lebaron, P

    2010-11-01

    Fixed cells with different nucleic acid contents and scatter properties (low nucleic acid [LNA], high nucleic acid 1 [HNA1], and HNA2) were sorted by flow cytometry (FCM). For each sort, 10,000 cells were efficiently captured on poly-l-lysine-coated microplates, resulting in efficient and reproducible PCR amplification.

  2. Process development and exergy cost sensitivity analysis of a hybrid molten carbonate fuel cell power plant and carbon dioxide capturing process

    Science.gov (United States)

    Mehrpooya, Mehdi; Ansarinasab, Hojat; Moftakhari Sharifzadeh, Mohammad Mehdi; Rosen, Marc A.

    2017-10-01

    An integrated power plant with a net electrical power output of 3.71 × 105 kW is developed and investigated. The electrical efficiency of the process is found to be 60.1%. The process includes three main sub-systems: molten carbonate fuel cell system, heat recovery section and cryogenic carbon dioxide capturing process. Conventional and advanced exergoeconomic methods are used for analyzing the process. Advanced exergoeconomic analysis is a comprehensive evaluation tool which combines an exergetic approach with economic analysis procedures. With this method, investment and exergy destruction costs of the process components are divided into endogenous/exogenous and avoidable/unavoidable parts. Results of the conventional exergoeconomic analyses demonstrate that the combustion chamber has the largest exergy destruction rate (182 MW) and cost rate (13,100 /h). Also, the total process cost rate can be decreased by reducing the cost rate of the fuel cell and improving the efficiency of the combustion chamber and heat recovery steam generator. Based on the total avoidable endogenous cost rate, the priority for modification is the heat recovery steam generator, a compressor and a turbine of the power plant, in rank order. A sensitivity analysis is done to investigate the exergoeconomic factor parameters through changing the effective parameter variations.

  3. Energy and exergy analyses of an integrated gasification combined cycle power plant with CO2 capture using hot potassium carbonate solvent.

    Science.gov (United States)

    Li, Sheng; Jin, Hongguang; Gao, Lin; Mumford, Kathryn Anne; Smith, Kathryn; Stevens, Geoff

    2014-12-16

    Energy and exergy analyses were studied for an integrated gasification combined cycle (IGCC) power plant with CO2 capture using hot potassium carbonate solvent. The study focused on the combined impact of the CO conversion ratio in the water gas shift (WGS) unit and CO2 recovery rate on component exergy destruction, plant efficiency, and energy penalty for CO2 capture. A theoretical limit for the minimal efficiency penalty for CO2 capture was also provided. It was found that total plant exergy destruction increased almost linearly with CO2 recovery rate and CO conversion ratio at low CO conversion ratios, but the exergy destruction from the WGS unit and the whole plant increased sharply when the CO conversion ratio was higher than 98.5% at the design WGS conditions, leading to a significant decrease in plant efficiency and increase in efficiency penalty for CO2 capture. When carbon capture rate was over around 70%, via a combination of around 100% CO2 recovery rate and lower CO conversion ratios, the efficiency penalty for CO2 capture was reduced. The minimal efficiency penalty for CO2 capture was estimated to be around 5.0 percentage points at design conditions in an IGCC plant with 90% carbon capture. Unlike the traditional aim of 100% CO conversion, it was recommended that extremely high CO conversion ratios should not be considered in order to decrease the energy penalty for CO2 capture and increase plant efficiency.

  4. Increased capture of pediatric surgical complications utilizing a novel case-log web application to enhance quality improvement.

    Science.gov (United States)

    Fisher, Jason C; Kuenzler, Keith A; Tomita, Sandra S; Sinha, Prashant; Shah, Paresh; Ginsburg, Howard B

    2017-01-01

    Documenting surgical complications is limited by multiple barriers and is not fostered in the electronic health record. Tracking complications is essential for quality improvement (QI) and required for board certification. Current registry platforms do not facilitate meaningful complication reporting. We developed a novel web application that improves accuracy and reduces barriers to documenting complications. We deployed a custom web application that allows pediatric surgeons to maintain case logs. The program includes a module for entering complication data in real time. Reminders to enter outcome data occur at key postoperative intervals to optimize recall of events. Between October 1, 2014, and March 31, 2015, frequencies of surgical complications captured by the existing hospital reporting system were compared with data aggregated by our application. 780 cases were captured by the web application, compared with 276 cases registered by the hospital system. We observed an increase in the capture of major complications when compared to the hospital dataset (14 events vs. 4 events). This web application improved real-time reporting of surgical complications, exceeding the accuracy of administrative datasets. Custom informatics solutions may help reduce barriers to self-reporting of adverse events and improve the data that presently inform pediatric surgical QI. Diagnostic study/Retrospective study. Level III - case control study. Copyright © 2017 Elsevier Inc. All rights reserved.

  5. Final Techno-Economic Analysis of 550 MWe Supercritical PC Power Plant CO2 Capture with Linde-BASF Advanced PCC Technology

    Energy Technology Data Exchange (ETDEWEB)

    Bostick, Devin [Linde LLC, Murray Hill, NJ (United States); Stoffregen, Torsten [Linde AG Linde Engineering Division, Dresden (Germany); Rigby, Sean [BASF Corporation, Houston, TX (United States)

    2017-01-09

    , along with quantification of the magnitude of the reductions achieved by each of these factors, are also discussed. Additionally, a high-level techno-economic analysis of one more highly advanced Linde-BASF PCC configuration case (LB1-CREB) is also presented to demonstrate the significant impact of innovative PCC plant process design improvements on further reducing COE and cost of CO2 captured for overall plant cost and performance comparison purposes. Overall, the net efficiency of the integrated 550 MWe supercritical PC power plant with CO2 capture is increased from 28.4% with the DOE/NETL Case 12 reference to 30.9% with the Linde-BASF PCC plant previously presented utilizing the BASF OASE® blue solvent [Ref. 6], and is further increased to 31.4% using Linde-BASF PCC plant with BASF OASE® blue solvent and an advanced SIH configuration. The Linde-BASF PCC plant incorporating the BASF OASE® blue solvent also results in significantly lower overall capital costs, thereby reducing the COE and cost of CO2 captured from $147.25/MWh and $56.49/MT CO2, respectively, for the reference DOE/NETL Case 12 plant, to $128.49/MWh and $41.85/MT CO2 for process case LB1, respectively, and $126.65/MWh and $40.66/MT CO2 for process case SIH, respectively. With additional innovative Linde-BASF PCC process configuration improvements, the COE and cost of CO2 captured can be further reduced to $125.51/MWh and $39.90/MT CO2 for LB1-CREB. Most notably, the Linde-BASF process options presented here have already demonstrated the potential to lower the cost of CO2 captured below the DOE target of $40/MT CO2 at the 550 MWe scale for second generation PCC technologies.

  6. Reducing water usage with rotary regenerative gas/gas heat exchangers in natural gas-fired power plants with post-combustion carbon capture

    OpenAIRE

    Herraiz, Laura; Hogg, Dougal; Cooper, Jim; Gibbins, Jon; Lucquiaud, Mathieu

    2015-01-01

    It is possible to greatly mitigate the increase of water usage associated with the addition of carbon capture to fossil fuel power generation. This article presents a first-of-a-kind feasibility study of a series of technology options with rotary regenerative gas/gas heat exchangers for the management of the water balance around post-combustion carbon capture process integrated with Combined Cycle Gas Turbine (CCGT) plants with and without exhaust gas recirculation (EGR). Hybrid cooling confi...

  7. Energy storage for improvement of wind power characteristics

    DEFF Research Database (Denmark)

    Rasmussen, Claus Nygaard

    2011-01-01

    Results from simulation of the influence of energy storage on the variability and availability of wind energy are presented here. Simulations have been done using a mathematical model of energy storage implemented in MATLAB. The obtained results show the quality improvement, of energy delivered...... by a combination of wind and energy storage, in relation to the size of the energy storage. The introduction of storage enables suppression of wind power fluctuations up to a timescale proportional to the storage energy capacity. Energy storage cannot provide availability of wind power at all times, but it can...... guarantee that a certain fraction of average wind power will be available within a given timeframe. The amount of storage energy capacity necessary for significant improvement of wind power availability, within a given period, is found to be approximately 20% of the energy produced in that period...

  8. Improved parametrization of the unified model for alpha decay and alpha capture

    CERN Document Server

    Denisov, V Yu; Sedykh, I Yu

    2015-01-01

    The updated data for the ground-state-to-ground-state alpha-transition half-lives in 401 nuclei and the alpha capture cross sections of 40Ca, 44Ca, 59Co, 208Pb and 209Bi are well described in the framework of the unified model for alpha-decay and alpha-capture. The updated values of the alpha decay half-lives, the binding energies of nuclei, the spins of parent and daughter nuclei, and the surface deformation parameters are used for the reevaluation of the model parameters. The data for the ground-state-to-ground-state alpha-decay half-lives are also well described by the empirical relationships.

  9. Evaluation of Solid Sorbents As A Retrofit Technology for CO{sub 2} Capture from Coal-Fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Krutka, Holly; Sjostrom, Sharon

    2011-07-31

    Through a U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) funded cooperative agreement DE-NT0005649, ADA Environmental Solutions (ADA) has begun evaluating the use of solid sorbents for CO{sub 2} capture. The project objective was to address the viability and accelerate development of a solid-based CO{sub 2} capture technology. To meet this objective, initial evaluations of sorbents and the process / equipment were completed. First the sorbents were evaluated using a temperature swing adsorption process at the laboratory scale in a fixed-bed apparatus. A slipstream reactor designed to treat flue gas produced by coal-fired generation of nominally 1 kWe was designed and constructed, which was used to evaluate the most promising materials on a more meaningful scale using actual flue gas. In a concurrent effort, commercial-scale processes and equipment options were also evaluated for their applicability to sorbent-based CO{sub 2} capture. A cost analysis was completed that can be used to direct future technology development efforts. ADA completed an extensive sorbent screening program funded primarily through this project, DOE NETL cooperative agreement DE-NT0005649, with support from the Electric Power Research Institute (EPRI) and other industry participants. Laboratory screening tests were completed on simulated and actual flue gas using simulated flue gas and an automated fixed bed system. The following types and quantities of sorbents were evaluated: 87 supported amines, 31 carbon based materials, 6 zeolites, 7 supported carbonates (evaluated under separate funding), 10 hydrotalcites. Sorbent evaluations were conducted to characterize materials and down-select promising candidates for further testing at the slipstream scale. More than half of the materials evaluated during this program were supported amines. Based on the laboratory screening four supported amine sorbents were selected for evaluation at the 1 kW scale at two different

  10. Capture compound mass spectrometry--a powerful tool to identify novel c-di-GMP effector proteins.

    Science.gov (United States)

    Laventie, Benoît-Joseph; Nesper, Jutta; Ahrné, Erik; Glatter, Timo; Schmidt, Alexander; Jenal, Urs

    2015-01-01

    Considerable progress has been made during the last decade towards the identification and characterization of enzymes involved in the synthesis (diguanylate cyclases) and degradation (phosphodiesterases) of the second messenger c-di-GMP. In contrast, little information is available regarding the molecular mechanisms and cellular components through which this signaling molecule regulates a diverse range of cellular processes. Most of the known effector proteins belong to the PilZ family or are degenerated diguanylate cyclases or phosphodiesterases that have given up on catalysis and have adopted effector function. Thus, to better define the cellular c-di-GMP network in a wide range of bacteria experimental methods are required to identify and validate novel effectors for which reliable in silico predictions fail. We have recently developed a novel Capture Compound Mass Spectrometry (CCMS) based technology as a powerful tool to biochemically identify and characterize c-di-GMP binding proteins. This technique has previously been reported to be applicable to a wide range of organisms(1). Here we give a detailed description of the protocol that we utilize to probe such signaling components. As an example, we use Pseudomonas aeruginosa, an opportunistic pathogen in which c-di-GMP plays a critical role in virulence and biofilm control. CCMS identified 74% (38/51) of the known or predicted components of the c-di-GMP network. This study explains the CCMS procedure in detail, and establishes it as a powerful and versatile tool to identify novel components involved in small molecule signaling.

  11. Introducing Model Predictive Control for Improving Power Plant Portfolio Performance

    DEFF Research Database (Denmark)

    Edlund, Kristian Skjoldborg; Bendtsen, Jan Dimon; Børresen, Simon

    2008-01-01

    This paper introduces a model predictive control (MPC) approach for construction of a controller for balancing the power generation against consumption in a power system. The objective of the controller is to coordinate a portfolio consisting of multiple power plant units in the effort to perform...... reference tracking and disturbance rejection in an economically optimal way. The performance function is chosen as a mixture of the `1-norm and a linear weighting to model the economics of the system. Simulations show a significant improvement of the performance of the MPC compared to the current...

  12. Convex Relaxation of Power Dispatch for Voltage Stability Improvement

    DEFF Research Database (Denmark)

    Pedersen, Andreas Søndergaard; Blanke, Mogens; Jóhannsson, Hjörtur

    2015-01-01

    A method for enhancing the voltage stability ofa power system is presented in this paper. The method isbased on a stability-constrained optimal power flow approach,where dispatch is done such that a maximum L-index isminimised for all load busses in a transmission grid. It isshown that optimal...... dispatch is obtainable with enhancedmargins for voltage stability using a semidefinite relaxation ofthe optimal power flow problem, and that this problem canbe formulated as semidefinite program with a quasi-convexobjective. Numerical tests are performed on the IEEE-30 busand BPA systems. The feasibility...... of the method is demonstratedthrough demonstrating that improved voltage stability marginsare obtained for both systems....

  13. Combustion systems and power plants incorporating parallel carbon dioxide capture and sweep-based membrane separation units to remove carbon dioxide from combustion gases

    Science.gov (United States)

    Wijmans, Johannes G.; Merkel, Timothy C; Baker, Richard W.

    2011-10-11

    Disclosed herein are combustion systems and power plants that incorporate sweep-based membrane separation units to remove carbon dioxide from combustion gases. In its most basic embodiment, the invention is a combustion system that includes three discrete units: a combustion unit, a carbon dioxide capture unit, and a sweep-based membrane separation unit. In a preferred embodiment, the invention is a power plant including a combustion unit, a power generation system, a carbon dioxide capture unit, and a sweep-based membrane separation unit. In both of these embodiments, the carbon dioxide capture unit and the sweep-based membrane separation unit are configured to be operated in parallel, by which we mean that each unit is adapted to receive exhaust gases from the combustion unit without such gases first passing through the other unit.

  14. Efficient cycles for carbon capture CLC power plants based on thermally balanced redox reactors

    KAUST Repository

    Iloeje, Chukwunwike

    2015-10-01

    © 2015 Elsevier Ltd. The rotary reactor differs from most alternative chemical looping combustion (CLC) reactor designs because it maintains near-thermal equilibrium between the two stages of the redox process by thermally coupling channels undergoing oxidation and reduction. An earlier study showed that this thermal coupling between the oxidation and reduction reactors increases the efficiency by up to 2% points when implemented in a regenerative Brayton cycle. The present study extends this analysis to alternative CLC cycles with the objective of identifying optimal configurations and design tradeoffs. Results show that the increased efficiency from reactor thermal coupling applies only to cycles that are capable of exploiting the increased availability in the reduction reactor exhaust. Thus, in addition to the regenerative cycle, the combined CLC cycle and the combined-regenerative CLC cycle are suitable for integration with the rotary reactor. Parametric studies are used to compare the sensitivity of the different cycle efficiencies to parameters like pressure ratio, turbine inlet temperature, carrier-gas fraction and purge steam generation. One of the key conclusions from this analysis is that while the optimal efficiency for regenerative CLC cycle was the highest of the three (56% at 3. bars, 1200. °C), the combined-regenerative cycle offers a trade-off that combines a reasonably high efficiency (about 54% at 12. bars, 1200. °C) with much lower gas volumetric flow rate and consequently, smaller reactor size. Unlike the other two cycles, the optimal compressor pressure ratio for the regenerative cycle is weakly dependent on the design turbine inlet temperature. For the regenerative and combined regenerative cycles, steam production in the regenerator below 2× fuel flow rate improves exhaust recovery and consequently, the overall system efficiency. Also, given that the fuel side regenerator flow is unbalanced, it is more efficient to generate steam from the

  15. RFX machine and power supply improvements for RFP advanced studies

    Energy Technology Data Exchange (ETDEWEB)

    Piovan, R. E-mail: piovan@igi.pd.cnr.it; Gnesotto, F.; Ortolani, S.; Baker, W.; Barana, O.; Bettini, P.; Cavazzana, R.; Chitarin, G.; Dal Bello, S.; De Lorenzi, A.; Fiorentin, P.; Gaio, E.; Grando, L.; Luchetta, A.; Manduchi, G.; Marchiori, G.; Marcuzzi, D.; Masiello, A.; Milani, F.; Peruzzo, S.; Pomaro, N.; Sonato, P.; Taliercio, C.; Toigo, V.; Zaccaria, P.; Zanotto, L.; Zollino, G

    2001-10-01

    Experimental results and theoretical studies call for Reversed Field Experiment (RFX) machine and power supply improvements to allow studies that go beyond those of a conventional Reversed Field Pinch (RFP) with passively stabilized turbulent MHD dynamo. The new paths opened by recent results in RFX and other RFP machines are introduced; then the goals and the design lines of the technical modifications of RFX, mainly addressed to improve the first wall, the plasma magnetic boundaries and to increase the operational flexibility of the toroidal field circuit power supply, are reported.

  16. Injector power supplies reliability improvements at the Advanced Photon Source.

    Energy Technology Data Exchange (ETDEWEB)

    Hillman, A.; Pasky, S.; Sereno, N.; Soliday, R.; Wang, J.

    2006-01-01

    Operational goals for the Advanced Photon Source (APS) facility include 97% availability and a mean time between unscheduled beam losses (faults) of 70 hours, with more than 5000 user hours of scheduled beam per year. To meet this objective, our focus has been maximizing the mean time between faults (MTBF). We have made various hardware and software improvements to better operate and monitor the injector power supply systems. These improvements have been challenging to design and implement in light of the facility operating requirements but are critical to maintaining maximum reliability and availability of beam for user operations. This paper presents actions taken as well as future plans to continue improving injector power supply hardware and software to meet APS user operation goals. The Advanced Photon Source (APS) has two major components. The storage ring (SR) accelerator is the primary accelerator that delivers X-ray beams to users and uses over 1,400 power supplies. The injector accelerators provide beam to the SR and use 361 different supplies. The control system ranges from the standard VME-IOC and Allen Bradley to GESPAC with additional mini-PLCs for monitoring. Injector power supplies range from {approx}30 watts DC to a ramped peak of 4.6 megawatts in 250 ms. Finally, all accelerators use pulsed supplies, and some of them deliver peak power in megawatts. In the SR, each multipole and corrector magnet is separately powered, with only the main dipole magnets on a common bus. Independent power supplies provide increased flexibility, but place additional demands on power supply reliability. The APS reliability goals are 97% availability and 70 hours mean time to unscheduled beam loss. There are 5,129 user hours scheduled per year, 1,315 hours used for machine studies, and the remaining 2,316 hours used for maintenance. The present annual operating schedule provides for three user runs (typically 10 to 12 weeks long), and three machine shutdowns (typically

  17. Unpacking the mechanisms captured by a correlative species distribution model to improve predictions of climate refugia.

    Science.gov (United States)

    Briscoe, Natalie J; Kearney, Michael R; Taylor, Chris A; Wintle, Brendan A

    2016-07-01

    Climate refugia are regions that animals can retreat to, persist in and potentially then expand from under changing environmental conditions. Most forecasts of climate change refugia for species are based on correlative species distribution models (SDMs) using long-term climate averages, projected to future climate scenarios. Limitations of such methods include the need to extrapolate into novel environments and uncertainty regarding the extent to which proximate variables included in the model capture processes driving distribution limits (and thus can be assumed to provide reliable predictions under new conditions). These limitations are well documented; however, their impact on the quality of climate refugia predictions is difficult to quantify. Here, we develop a detailed bioenergetics model for the koala. It indicates that range limits are driven by heat-induced water stress, with the timing of rainfall and heat waves limiting the koala in the warmer parts of its range. We compare refugia predictions from the bioenergetics model with predictions from a suite of competing correlative SDMs under a range of future climate scenarios. SDMs were fitted using combinations of long-term climate and weather extremes variables, to test how well each set of predictions captures the knowledge embedded in the bioenergetics model. Correlative models produced broadly similar predictions to the bioenergetics model across much of the species' current range - with SDMs that included weather extremes showing highest congruence. However, predictions in some regions diverged significantly when projecting to future climates due to the breakdown in correlation between climate variables. We provide unique insight into the mechanisms driving koala distribution and illustrate the importance of subtle relationships between the timing of weather events, particularly rain relative to hot-spells, in driving species-climate relationships and distributions. By unpacking the mechanisms

  18. Different Algorithms for Improving Detection Power of Atomic Fluorescence Spectrometry

    Directory of Open Access Journals (Sweden)

    Jian Cui

    2012-11-01

    Full Text Available The purpose of detecting trace concentrations of analytes often is hindered by occurring noise in the signal curves of analytical methods. This is also a problem when different arsenic species (organic arsenic species such as arsanilic acid, nitarsone and roxarsone are to be determined in animal meat by HPLC-UV-HG-AFS, which is the basis of this work. In order to improve the detection power, methods of signal treatment may be applied. We show a comparison of convolution with Gaussian distribution curves, Fourier transform, and wavelet transform. It is illustrated how to estimate decisive parameters for these techniques. All methods result in improved limits of detection. Furthermore, applying baselines and evaluating peaks thoroughly is facilitated. However, there are differences. Fourier transform may be applied, but convolution with Gaussian distribution curves shows better results of improvement. The best of the three is wavelet transform, whereby the detection power is improved by factors of about 2.4

  19. Improving the safety of LWR power plants. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1980-04-01

    This report documents the results of the Study to identify current, potential research issues and efforts for improving the safety of Light Water Reactor (LWR) power plants. This final report describes the work accomplished, the results obtained, the problem areas, and the recommended solutions. Specifically, for each of the issues identified in this report for improving the safety of LWR power plants, a description is provided in detail of the safety significance, the current status (including information sources, status of technical knowledge, problem solution and current activities), and the suggestions for further research and development. Further, the issues are ranked for action into high, medium, and low priority with respect to primarily (a) improved safety (e.g. potential reduction in public risk and occupational exposure), and secondly (b) reduction in safety-related costs (improving or maintaining level of safety with simpler systems or in a more cost-effective manner).

  20. High temperature SMES for improving power system stabilities

    Institute of Scientific and Technical Information of China (English)

    CHENG ShiJie; TANG YueJin

    2007-01-01

    Superconducting magnetic energy storage (SMES) system has been proven very effective to improve power system stabilities. It is realized with superconductivity technology, power electronics and control theory. In order to promote the application of such kind control device and to further investigate the properties of the controller, a detail mathematic model of such control device is developed. Based on the developed model, extensive analysis including time domain simulation is carried out to investigate the characteristic of the SMES to compensate the unba- lanced dynamic active and reactive power of AC power system. The capability of SMES to increase power system transient and small signal perturbation stabilities are analyzed. A prototype SMES is developed, in which the conduction cooling and the high temperature superconductive techniques are used. The performance of the prototype is experimentally investigated in a laboratory environment. Very encouraging results are obtained. After a brief introduction of the SMES control system and the principle of its capability to improve power system stabilities, the details of the mathematic model, the theoretical analysis, the developed device and the experiment test results are all given in this paper.

  1. High temperature SMES for improving power system stabilities

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Superconducting magnetic energy storage (SMES) system has been proven very effective to improve power system stabilities. It is realized with superconductivity technology, power electronics and control theory. In order to promote the applica-tion of such kind control device and to further investigate the properties of the controller, a detail mathematic model of such control device is developed. Based on the developed model, extensive analysis including time domain simulation is carried out to investigate the characteristic of the SMES to compensate the unba- lanced dynamic active and reactive power of AC power system. The capability of SMES to increase power system transient and small signal perturbation stabilities are analyzed. A prototype SMES is developed, in which the conduction cooling and the high temperature superconductive techniques are used. The performance of the prototype is experimentally investigated in a laboratory environment. Very en-couraging results are obtained. After a brief introduction of the SMES control sys-tem and the principle of its capability to improve power system stabilities, the de-tails of the mathematic model, the theoretical analysis, the developed device and the experiment test results are all given in this paper.

  2. IMPROVEMENTS TO THE PASSIVE LOSSLESS SNUBBERS FOR POWER BRIDGE LEGS

    Institute of Scientific and Technical Information of China (English)

    He Xiangning; Yang Yuwen; Qian Zhaoming; Barry W. Williams; Stephen J. Finney

    2001-01-01

    The paper considers three common snubber circuits used on gate turn-off thyristor and/or insulated gate bipolar transistor inverters. The three snubbers are passive lossless circuits for power bridge legs, and the improvements and modifications to these snubber circuits are presented. The comparative features and operation of the three improved energy recovery snubbers are discussed and supported by PSPICE simulations and experimental results.

  3. Recent brightness improvements of 976 nm high power laser bars

    Science.gov (United States)

    Bachmann, Alexander; Lauer, Christian; Furitsch, Michael; König, Harald; Müller, Martin; Strauß, Uwe

    2017-02-01

    Pump modules for fiber lasers and fiber-coupled direct diode laser systems require laser diodes with a high beam quality. While in fast axis direction diode lasers exhibit a nearly diffraction limited output beam, the maximum usable output power is usually limited by the slow axis divergence blooming at high power levels. Measures to improve the lateral beam quality are subject of extensive research. Among the many influencing factors are the chip temperature, thermal crosstalk between emitters, thermal lensing, lateral waveguiding and lateral mode structure. We present results on the improvements of the lateral beam divergence and brightness of gain-guided mini-bars for emission at 976 nm. For efficient fiber coupling into a 200 μm fiber with NA 0.22, the upper limit of the lateral beam parameter product is 15.5 mm mrad. Within the last years, the power level at this beam quality has been improved from 44 W to 52 W for the chips in production, enabling more cost efficient pump modules and laser systems. Our work towards further improvements of the beam quality focuses on advanced chip designs featuring reduced thermal lensing and mode shaping. Recent R&D results will be presented, showing a further improvement of the beam quality by 15%. Also, results of a chip design with an improved lateral emitter design for highest brightness levels will be shown, yielding in a record high brightness saturation of 4.8 W/mm mrad.

  4. Improving Size and Power in Unit Root Testing

    DEFF Research Database (Denmark)

    Haldrup, Niels; Jansson, Michael

    of recent contributions to improve upon both size and power of unit root tests and in so doing the approach of using rigorous statistical optimality criteria in the development of such tests is stressed. In addition to presenting tests where improved size can be achieved by modifying the standard Dickey......A frequent criticism of unit root tests concerns the poor power and size properties that many of such testsexhibit. However, the past decade or so intensive research has been conducted to alleviate these problems and great advances have been made. The present paper provides a selective survey......-Fuller class of tests, the paper presents theory of optimal testing and the construction of power envelopes for unit root tests underdifferent conditions allowing for serial correlation, deterministic components, assumptions regarding the initial condition, non-Gaussian errors, and the use of covariates....

  5. Designing incentive market mechanisms for improving restructured power system reliabilities

    DEFF Research Database (Denmark)

    Ding, Yi; Østergaard, Jacob; Wu, Qiuwei

    2011-01-01

    In a restructured power system, the monopoly generation utility is replaced by different electricity producers. There exists extreme price volatility caused by random failures by generation or/and transmission systems. In these cases, producers' profits can be much higher than those in the normal...... mechanisms for improving the restructured power system reliabilities have been designed in this paper. In the proposed incentive mechanisms, penalty will be implemented on a producer if the failures of its generator(s) result in the variation of electricity prices. Incentive market mechanisms can motivate...... state. The reliability management of producers usually cannot be directly controlled by the system operators in a restructured power system. Producers may have no motivation to improve their reliabilities, which can result in serious system unreliability issues in the new environment. Incentive market...

  6. Wind turbine power tracking using an improved multimodel quadratic approach.

    Science.gov (United States)

    Khezami, Nadhira; Benhadj Braiek, Naceur; Guillaud, Xavier

    2010-07-01

    In this paper, an improved multimodel optimal quadratic control structure for variable speed, pitch regulated wind turbines (operating at high wind speeds) is proposed in order to integrate high levels of wind power to actively provide a primary reserve for frequency control. On the basis of the nonlinear model of the studied plant, and taking into account the wind speed fluctuations, and the electrical power variation, a multimodel linear description is derived for the wind turbine, and is used for the synthesis of an optimal control law involving a state feedback, an integral action and an output reference model. This new control structure allows a rapid transition of the wind turbine generated power between different desired set values. This electrical power tracking is ensured with a high-performance behavior for all other state variables: turbine and generator rotational speeds and mechanical shaft torque; and smooth and adequate evolution of the control variables. 2010 ISA. Published by Elsevier Ltd. All rights reserved.

  7. Improving geothermal power plants with a binary cycle

    Science.gov (United States)

    Tomarov, G. V.; Shipkov, A. A.; Sorokina, E. V.

    2015-12-01

    The recent development of binary geothermal technology is analyzed. General trends in the introduction of low-temperature geothermal sources are summarized. The use of single-phase low-temperature geothermal fluids in binary power plants proves possible and expedient. The benefits of power plants with a binary cycle in comparison with traditional systems are shown. The selection of the working fluid is considered, and the influence of the fluid's physicochemical properties on the design of the binary power plant is discussed. The design of binary power plants is based on the chemical composition and energy potential of the geothermal fluids and on the landscape and climatic conditions at the intended location. Experience in developing a prototype 2.5 MW Russian binary power unit at Pauzhetka geothermal power plant (Kamchatka) is outlined. Most binary systems are designed individually for a specific location. Means of improving the technology and equipment at binary geothermal power plants are identified. One option is the development of modular systems based on several binary systems that employ the heat from the working fluid at different temperatures.

  8. Does NASA SMAP Improve the Accuracy of Power Outage Models?

    Science.gov (United States)

    Quiring, S. M.; McRoberts, D. B.; Toy, B.; Alvarado, B.

    2016-12-01

    Electric power utilities make critical decisions in the days prior to hurricane landfall that are primarily based on the estimated impact to their service area. For example, utilities must determine how many repair crews to request from other utilities, the amount of material and equipment they will need to make repairs, and where in their geographically expansive service area to station crews and materials. Accurate forecasts of the impact of an approaching hurricane within their service area are critical for utilities in balancing the costs and benefits of different levels of resources. The Hurricane Outage Prediction Model (HOPM) are a family of statistical models that utilize predictions of tropical cyclone windspeed and duration of strong winds, along with power system and environmental variables (e.g., soil moisture, long-term precipitation), to forecast the number and location of power outages. This project assesses whether using NASA SMAP soil moisture improves the accuracy of power outage forecasts as compared to using model-derived soil moisture from NLDAS-2. A sensitivity analysis is employed since there have been very few tropical cyclones making landfall in the United States since SMAP was launched. The HOPM is used to predict power outages for 13 historical tropical cyclones and the model is run using twice, once with NLDAS soil moisture and once with SMAP soil moisture. Our results demonstrate that using SMAP soil moisture can have a significant impact on power outage predictions. SMAP has the potential to enhance the accuracy of power outage forecasts. Improved outage forecasts reduce the duration of power outages which reduces economic losses and accelerates recovery.

  9. 电力行业碳捕集现状和发展趋势%Cureent Status and Development of Carbon Capture in Power Generation Industry

    Institute of Scientific and Technical Information of China (English)

    翟明洋; 林千果; 马丽; 徐梓忻; 王文双

    2014-01-01

    Three kinds of CO2 capture technologies, including pre-combustion capture technology, post-combustion capture technology and oxy-fuel capture technology, were comprehensively investigated.Through comparing a variety of CO2 capture technologies the advantages and disadvantages and the scope of application of various technologies were discussed. Furthermore, survey of research works of CO2 capture and a number of demonstration projects were conducted. The current status, potential barriers and future trends of CO2 capture technology in power industry of China were further discussed.%全面介绍了燃煤电厂3种CO2捕集技术,包括燃烧前捕集,燃烧后捕集以及富氧燃烧捕集技术。通过对各种CO2捕集技术的对比,提出各种捕集方法的适用范围和优、缺点。在此基础上调查了我国碳捕集技术的研究以及碳捕集示范工程项目的进展,分析了我国电力行业碳捕集技术现状和面临的问题并对电力行业碳捕集发展趋势进行了探讨。

  10. The hybrid MPC-MINLP algorithm for optimal operation of coal-fired power plants with solvent based post-combustion CO2 capture

    Directory of Open Access Journals (Sweden)

    Norhuda Abdul Manaf

    2017-03-01

    Full Text Available This paper presents an algorithm that combines model predictive control (MPC with MINLP optimization and demonstrates its application for coal-fired power plants retrofitted with solvent based post-combustion CO2 capture (PCC plant. The objective function of the optimization algorithm works at a primary level to maximize plant economic revenue while considering an optimal carbon capture profile. At a secondary level, the MPC algorithm is used to control the performance of the PCC plant. Two techno-economic scenarios based on fixed (capture rate is constant and flexible (capture rate is variable operation modes are developed using actual electricity prices (2011 with fixed carbon prices ($AUD 5, 25, 50/tonne-CO2 for 24 h periods. Results show that fixed operation mode can bring about a ratio of net operating revenue deficit at an average of 6% against the superior flexible operation mode.

  11. Capturing spatiotemporal variation in wildfires for improving postwildfire debris-flow hazard assessments: Chapter 20

    Science.gov (United States)

    Haas, Jessica R.; Thompson, Matthew P.; Tillery, Anne C.; Scott, Joe H.

    2017-01-01

    Wildfires can increase the frequency and magnitude of catastrophic debris flows. Integrated, proactive natural hazard assessment would therefore characterize landscapes based on the potential for the occurrence and interactions of wildfires and postwildfire debris flows. This chapter presents a new modeling effort that can quantify the variability surrounding a key input to postwildfire debris-flow modeling, the amount of watershed burned at moderate to high severity, in a prewildfire context. The use of stochastic wildfire simulation captures variability surrounding the timing and location of ignitions, fire weather patterns, and ultimately the spatial patterns of watershed area burned. Model results provide for enhanced estimates of postwildfire debris-flow hazard in a prewildfire context, and multiple hazard metrics are generated to characterize and contrast hazards across watersheds. Results can guide mitigation efforts by allowing planners to identify which factors may be contributing the most to the hazard rankings of watersheds.

  12. NWTC Aerodynamics Studies Improve Energy Capture and Lower Costs of Wind-Generated Electricity

    Energy Technology Data Exchange (ETDEWEB)

    2015-08-01

    Researchers at the National Wind Technology Center (NWTC) at the National Renewable Energy Laboratory (NREL) have expanded wind turbine aerodynamic research from blade and rotor aerodynamics to wind plant and atmospheric inflow effects. The energy capture from wind plants is dependent on all of these aerodynamic interactions. Research at the NWTC is crucial to understanding how wind turbines function in large, multiple-row wind plants. These conditions impact the cumulative fatigue damage of turbine structural components that ultimately effect the useful lifetime of wind turbines. This work also is essential for understanding and maximizing turbine and wind plant energy production. Both turbine lifetime and wind plant energy production are key determinants of the cost of wind-generated electricity.

  13. The Economic Merits of Flexible Carbon Capture and Sequestration as a Compliance Strategy with the Clean Power Plan.

    Science.gov (United States)

    Craig, Michael T; Jaramillo, Paulina; Zhai, Haibo; Klima, Kelly

    2017-02-07

    Carbon capture and sequestration (CCS) may be a key technology for achieving large CO2 emission reductions. Relative to "normal" CCS, "flexible" CCS retrofits include solvent storage that allows the generator to temporarily reduce the CCS parasitic load and increase the generator's net efficiency, capacity, and ramp rate. Due to this flexibility, flexible CCS generators provide system benefits that normal CCS generators do not, which could make flexible CCS an economic CO2 emission reduction strategy. Here, we estimate the system-level cost effectiveness of reducing CO2 emissions with flexible CCS compared to redispatching (i.e., substituting gas- for coal-fired electricity generation), wind, and normal CCS under the Clean Power Plan (CPP) and a hypothetical more stringent CO2 emission reduction target ("stronger CPP"). Using a unit commitment and economic dispatch model, we find flexible CCS achieves more cost-effective emission reductions than normal CCS under both reduction targets, indicating that policies that promote CCS should encourage flexible CCS. However, flexible CCS is less cost effective than wind under both reduction targets and less and more cost effective than redispatching under the CPP and stronger CPP, respectively. Thus, CCS will likely be a minor CPP compliance strategy but may play a larger role under a stronger emission reduction target.

  14. Modeling Analysis and Improvement of Power Loss in Microgrid

    Directory of Open Access Journals (Sweden)

    H. Lan

    2015-01-01

    Full Text Available The consumption of conventional energy sources and environmental concerns have resulted in rapid growth in the amount of renewable energy introduced to power systems. With the help of distributed generations (DG, the improvement of power loss and voltage profile can be the salient benefits. However, studies show that improper placement and size of energy storage system (ESS lead to undesired power loss and the risk of voltage stability, especially in the case of high renewable energy penetration. To solve the problem, this paper sets up a microgrid based on IEEE 34-bus distribution system which consists of wind power generation system, photovoltaic generation system, diesel generation system, and energy storage system associated with various types of load. Furthermore, the particle swarm optimization (PSO algorithm is proposed in the paper to minimize the power loss and improve the system voltage profiles by optimally managing the different sorts of distributed generations under consideration of the worst condition of renewable energy production. The established IEEE 34-bus system is adopted to perform case studies. The detailed simulation results for each case clearly demonstrate the necessity of optimal management of the system operation and the effectiveness of the proposed method.

  15. Improved power transfer to wearable systems through stretchable magnetic composites

    Science.gov (United States)

    Lazarus, N.; Bedair, S. S.

    2016-05-01

    The use of wireless power transfer is common in stretchable electronics since physical wiring can be easily destroyed as the system is stretched. This work presents the first demonstration of improved inductive power coupling to a stretchable system through the addition of a thin layer of ferroelastomeric material. A ferroelastomer, an elastomeric polymer loaded with magnetic particulates, has a permeability greater than one while retaining the ability to survive significant mechanical strains. A recently developed ferroelastomer composite based on sendust platelets within a soft silicone elastomer was incorporated into liquid metal stretchable inductors based on the liquid metal galinstan in fluidic channels. For a single-turn inductor, the maximum power transfer efficiency rises from 71 % with no backplane, to 81 % for a rigid ferrite backplane on the transmitter side alone, to 86 % with a ferroelastomer backplane on the receiver side as well. The coupling between a commercial wireless power transmitter coil with ferrite backplane to a five-turn liquid metal inductor was also investigated, finding an improvement in power transfer efficiency from 81 % with only a rigid backplane to 90 % with the addition of the ferroelastomer backplane. Both the single and multi-turn inductors were demonstrated surviving up to 50 % uniaxial applied strain.

  16. Investigation of Improved Methods in Power Transfer Efficiency for Radiating Near-Field Wireless Power Transfer

    Directory of Open Access Journals (Sweden)

    Hesheng Cheng

    2016-01-01

    Full Text Available A metamaterial-inspired efficient electrically small antenna is proposed, firstly. And then several improving power transfer efficiency (PTE methods for wireless power transfer (WPT systems composed of the proposed antenna in the radiating near-field region are investigated. Method one is using a proposed antenna as a power retriever. This WPT system consisted of three proposed antennas: a transmitter, a receiver, and a retriever. The system is fed by only one power source. At a fixed distance from receiver to transmitter, the distance between the transmitter and the retriever is turned to maximize power transfer from the transmitter to the receiver. Method two is using two proposed antennas as transmitters and one antenna as receiver. The receiver is placed between the two transmitters. In this system, two power sources are used to feed the two transmitters, respectively. By adjusting the phase difference between the two feeding sources, the maximum PTE can be obtained at the optimal phase difference. Using the same configuration as method two, method three, where the maximum PTE can be increased by regulating the voltage (or power ratio of the two feeding sources, is proposed. In addition, we combine the proposed methods to construct another two schemes, which improve the PTE at different extent than classical WPT system.

  17. Guide for prioritizing power plant productivity improvement projects: handbook of availability improvement methodology

    Energy Technology Data Exchange (ETDEWEB)

    1981-09-15

    As part of its program to help improve electrical power plant productivity, the Department of Energy (DOE) has developed a methodology for evaluating productivity improvement projects. This handbook presents a simplified version of this methodology called the Availability Improvement Methodology (AIM), which provides a systematic approach for prioritizing plant improvement projects. Also included in this handbook is a description of data taking requirements necessary to support the AIM methodology, benefit/cost analysis, and root cause analysis for tracing persistent power plant problems. In applying the AIM methodology, utility engineers should be mindful that replacement power costs are frequently greater for forced outages than for planned outages. Equivalent availability includes both. A cost-effective ranking of alternative plant improvement projects must discern between those projects which will reduce forced outages and those which might reduce planned outages. As is the case with any analytical procedure, engineering judgement must be exercised with respect to results of purely mathematical calculations.

  18. Improvements in electric power supply in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Minovskii, Yu.P.; Nabokov, Eh.P.; Savel' ev, G.P.

    1985-01-01

    Reviews measures taken by major coal producing countries to increase output levels. Discusses research carried out into advance design of equipment in FRG, UK, USA and France and proposes establishment of central automatic control of electric power supply system in Soviet mines, improvement in underground power supply equipment, increase in reliability, stabilization of standby capacity in low voltage circuits, maintenance-free electrical equipment, and efficient spare part storage in underground workings. States that introduction of the proposed system (details are given) will ensure that Soviet mines will eventually reach the development level of foreign mines. 2 refs.

  19. A Review Paper on Power Consumption Improvements in WSN

    Directory of Open Access Journals (Sweden)

    Mallika Mhatre

    2016-06-01

    Full Text Available : Wireless Sensor network (WSN is a network of low-cost, low-power, multifunctional, small size sensor nodes which are densely deployed inside a physical environment to collect, process and transmit the information to sink node. As Sensor nodes are generally battery-powered, it is necessary to balance between power consumption and energy storage capacity to sustain sensor node's operational life. Therefore one of the important challenge in WSN is to improve power consumption efficiently to prolong network lifetime by minimizing the amount of data transmissions throughout the network and maximizing node's low power residence time. In this paper, two energy optimization techniques, Cluster-Based energy efficient routing (CBER scheme and extension to IEEE 802.15.4 standard by dynamic rate adaption and control for energy reduction (DRACER protocol for wireless sensor networks has been reviewed. CBER technique increases network lifetime by reducing Hot Spot problem and end-to-end energy consumption using multi-hop wireless routing whereas DRACER protocol reduces network latency and average power consumption by minimizing network overhead using automatic data rate selection process. So, both of these techniques, if utilized in combination, it is possible to achieve very high energy efficiency in WSN.

  20. A research needs assessment for the capture, utilization and disposal of carbon dioxide from fossil fuel-fired power plants. Volume 1, Executive summary: Final report

    Energy Technology Data Exchange (ETDEWEB)

    1993-07-01

    This study identifies and assesses system approaches in order to prioritize research needs for the capture and non-atmospheric sequestering of a significant portion of the carbon dioxide (CO{sub 2}) emitted from fossil fuel-fired electric power plants (US power plants presently produce about 7% of the world`s CO{sub 2} emissions). The study considers capture technologies applicable either to existing plants or to those that optimistically might be demonstrated on a commercial scale over the next twenty years. Specific conclusions are as follows: (1) To implement CO{sub 2} capture and sequestration on a national scale will decrease power plant net efficiencies and significantly increase the cost of electricity. To make responsible societal decisions, accurate and consistent economic and environmental analysis of all alternatives for atmospheric CO{sub 2} mitigation are required. (2) Commercial CO{sub 2} capture technology, though expensive and energy intensive, exists today. (3) The most promising approach to more economical CO{sub 2} capture is to develop power plant systems that facilitate efficient CO{sub 2} capture. (4) While CO{sub 2} disposal in depleted oil and gas reservoirs is feasible today, the ability to dispose of large quantities Of CO{sub 2} is highly uncertain because of both technical and institutional issues. Disposal into the deep ocean or confined aquifers offers the potential for large quantity disposal, but there are technical, safety, liability, and environmental issues to resolve. Therefore, the highest priority research should focus on establishing the feasibility of large scale disposal options.

  1. Simultaneous multiview capture and fusion improves spatial resolution in wide-field and light-sheet microscopy

    Science.gov (United States)

    Wu, Yicong; Chandris, Panagiotis; Winter, Peter W.; Kim, Edward Y.; Jaumouillé, Valentin; Kumar, Abhishek; Guo, Min; Leung, Jacqueline M.; Smith, Corey; Rey-Suarez, Ivan; Liu, Huafeng; Waterman, Clare M.; Ramamurthi, Kumaran S.; La Riviere, Patrick J.; Shroff, Hari

    2016-01-01

    Most fluorescence microscopes are inefficient, collecting only a small fraction of the emitted light at any instant. Besides wasting valuable signal, this inefficiency also reduces spatial resolution and causes imaging volumes to exhibit significant resolution anisotropy. We describe microscopic and computational techniques that address these problems by simultaneously capturing and subsequently fusing and deconvolving multiple specimen views. Unlike previous methods that serially capture multiple views, our approach improves spatial resolution without introducing any additional illumination dose or compromising temporal resolution relative to conventional imaging. When applying our methods to single-view wide-field or dual-view light-sheet microscopy, we achieve a twofold improvement in volumetric resolution (~235 nm × 235 nm × 340 nm) as demonstrated on a variety of samples including microtubules in Toxoplasma gondii, SpoVM in sporulating Bacillus subtilis, and multiple protein distributions and organelles in eukaryotic cells. In every case, spatial resolution is improved with no drawback by harnessing previously unused fluorescence. PMID:27761486

  2. Trends in Global Demonstrations of Carbon Management Technologies to Advance Coal- Based Power Generation With Carbon Capture and Storage

    Science.gov (United States)

    Cohen, K. K.; Plasynski, S.; Feeley, T. J.

    2008-05-01

    Atmospheric CO2 concentrations increased an estimated 35% since preindustrial levels two centuries ago, reportedly due to the burning of fossil fuels combined with increased deforestation. In the U.S., energy-related activities account for 75% of anthropogenic greenhouse gas (GHG) emissions, with more than 50% from large stationary sources such as power plants and about one-third from transportation. Mitigation technologies for CO2 atmospheric stabilization based on energy and economic scenarios include coal-based power plant- carbon capture and storage (CCS), and the U.S. Department of Energy (DOE) is assessing CCS operations and supporting technologies at U.S. locations and opportunities abroad reported here. The Algerian In Salah Joint Industry Project injecting 1 million tons CO2 (MtCO2)/year into a gas field sandstone, and the Canadian Weyburn-Midale CO2 Monitoring and Storage Project injecting over 1.8 MtCO2/year into carbonate oil reservoirs are ongoing industrial-scale storage operations DOE participates in. DOE also supports mid-scale CCS demonstrations at the Australian Otway Project and CO2SINK in Germany. Enhanced oil recovery operations conducted for decades in west Texas and elsewhere have provided the industrial experience to build on, and early pilots such as Frio-I Texas in 2004 have spearheaded technology deployment. While injecting 1,600 tons of CO2 into a saline sandstone at Frio, time-lapse borehole and surface seismic detected P-wave velocity decreases and reflection amplitude changes resulting from the replacement of brine with CO2 in the reservoir. Just two of many cutting-edge technologies tested at Frio, these and others are now deployed by U.S. researchers with international teams to evaluate reservoir injectivity, capacity, and integrity, as well as to assess CO2 spatial distribution, trapping, and unlikely leakage. Time-lapse Vertical Seismic Profiling at Otway and microseismic at In Salah and Otway, monitor injection and reservoir

  3. Geometrical Optimization for Improved Power Capture of Multi-Level Overtopping Based Wave Energy Converters

    DEFF Research Database (Denmark)

    Margheritini, Lucia; Victor, L.; Kofoed, Jens Peter

    2009-01-01

    In multi-level wave energy converters the water from incoming waves is stored in reservoirs one on top of the other. Prevision formula for the overtopping flow rates in the individual reservoirs is fundamental for dimensioning correctly the turbines and optimizing the device. Having a number...... words, the opening between two consecutive reservoirs. 13 different geometries have been tested in 2D irregular waves and a new formulation for prediction of overtopping in multilevel structures is presented....

  4. Improve power quality of coal mine power network based on gray system theory

    Institute of Scientific and Technical Information of China (English)

    ZHU En-guo; YANG Gong-xun; XU Shu-ge; MA Gui-cun

    2007-01-01

    Unified Power Quality Controller(UPQC) was proposed to comprehensively improve power quality of coal mine power network and its basic structure and operation principle was introduced. In order to overcome time lag of Active Power Filter(APF) in compensating harmonic and reactive current, a novel method based on gray system theory was proposed to predict harmonic current and other distortion component. The mathematical model of component to be compensated was constructed by data sequence of distortion component, which could exactly forecast compensation signal of next period.The optimal control strategy was selected according to the principle of output signal approaching component to be compensated as near as possible. Before predicating each time the oldest data was eliminated while the latest data was added to data sequence.Then new predication model was established once again. The results show that the method can always construct mathematical model with variation of system parameters, reflect the latest state of system and not increase calculation quantity. The feasible and effective control strategy can improve power quality of coal mine power network.

  5. Power Factor Improvement for Pumping Stations using Capacitor Banks

    Science.gov (United States)

    Mohamad, M. M.; Abd El-gawad, Amal F.; Ramadan, H. S.

    2016-10-01

    One of the fundamental problems affects the performance of pumping stations is its relative high operational cost. As three-phase induction motors are the main prime mover of pumping stations and considered the most widely used electrical motors due to their reliability, ease of maintenance. However, its major problem is the low power factor which results in high electric energy consumption. Energy will be saved when power factor is improved. The main objective of this paper is studying the power factor improvement in El sadaa Pumping Station because of its low operating efficiency which goes from 20 % to 25 %and calculating penalty, ponus and savings in each cases. The correction is achieved by the addition of capacitor banks in parallel with the connected motor circuits and can be applied to the starter, applied at the switchboard or the distribution panel. A model of this station is created using MatlabTM Simulink. Then the determination of induction motor parameters is performed. The station model is discussed. From the simulation results, the power factor enhancement of the pumping station is highlighted.

  6. Optimal Reactive Power Dispatch using Improved Differential Evolution Algorithm

    Directory of Open Access Journals (Sweden)

    Hamid Falaghi

    2014-12-01

    Full Text Available Reactive power dispatch plays a key role in secure and economic operation of power systems. Optimal reactive power dispatch (ORPD is a non-linear optimization problem which includes both continues and discrete variables. Due to complex characteristics, heuristic and evolutionary based optimization approaches have become effective tools to solve the ORPD problem. In this paper, a new optimization approach based on improved differential evolution (IDE has been proposed to solve the ORPD problem. IDE is an improved version of differential evolution optimization algorithm in which new solutions are produced in respect to global best solution. In the proposed approach, IDE determines the optimal combination of control variables including generator voltages, transformer taps and setting of VAR compensation devices to obtain minimum real power losses. In order to demonstrate the applicability and efficiency of the proposed IDE based approach, it has been tested on the IEEE 14 and 57-bus test systems and obtained results are compared with those obtained using other existing methods. Simulation results show that the proposed approach is superior to the other existing methods.

  7. Technical and Energy Performance of an Advanced, Aqueous Ammonia-Based CO2 Capture Technology for a 500 MW Coal-Fired Power Station.

    Science.gov (United States)

    Li, Kangkang; Yu, Hai; Feron, Paul; Tade, Moses; Wardhaugh, Leigh

    2015-08-18

    Using a rate-based model, we assessed the technical feasibility and energy performance of an advanced aqueous-ammonia-based postcombustion capture process integrated with a coal-fired power station. The capture process consists of three identical process trains in parallel, each containing a CO2 capture unit, an NH3 recycling unit, a water separation unit, and a CO2 compressor. A sensitivity study of important parameters, such as NH3 concentration, lean CO2 loading, and stripper pressure, was performed to minimize the energy consumption involved in the CO2 capture process. Process modifications of the rich-split process and the interheating process were investigated to further reduce the solvent regeneration energy. The integrated capture system was then evaluated in terms of the mass balance and the energy consumption of each unit. The results show that our advanced ammonia process is technically feasible and energy-competitive, with a low net power-plant efficiency penalty of 7.7%.

  8. Comprehensive Evaluation of a CO2-Capturing NOx-Free Repowering System with Utilization of Middle Pressure Steam in a Thermal Power Plant

    Science.gov (United States)

    Sik Pak, Pyong

    A CO2-capturing NOx-free H2O turbine power generation system is proposed in which middle pressure steam produced in a thermal power plant is utilized to increase generated power when demand for electricity is large. The proposed system can capture all the generated CO2 based on the oxygen combustion method and emits no NOx, so that it causes no urban and global environmental problems. A combined cycle power generation system with 200MW gas turbine power output is adopted as an example of a thermal power plant. It was assumed that 32 t/h of steam with 25kg/cm2 pressure produced at waste heat recovery boiler was utilized in the proposed system.It has been shown through simulation study that increase of power output by 11.8MW or 4.51% of the rated output is possible with no efficiency decrease. The amount of CO2 reduction is estimated to be 19600t/y.The unit cost of generated power is estimated to be 8.38yen/kWh, annual gross profit of the proposed system 271 million yen, depreciation year 4.87, and thus the proposed system is estimated to be economically feasible.

  9. The ZEBRA electric vehicle battery: power and energy improvements

    Science.gov (United States)

    Galloway, Roy C.; Haslam, Steven

    Vehicle trials with the first sodium/nickel chloride ZEBRA batteries indicated that the pulse power capability of the battery needed to be improved towards the end of the discharge. A research programme led to several design changes to improve the cell which, in combination, have improved the power of the battery to greater than 150 W kg -1 at 80% depth of discharge. Bench and vehicle tests have established the stability of the high power battery over several years of cycling. The gravimetric energy density of the first generation of cells was less than 100 Wh kg -1. Optimisation of the design has led to a cell with a specific energy of 120 Wh kg -1 or 86 Wh kg -1 for a 30 kWh battery. Recently, the cell chemistry has been altered to improve the useful capacity. The cell is assembled in the over-discharged state and during the first charge the following reactions occur: at 1.6 V: Al+4NaCl=NaAlCl 4+3Na; at 2.35 V: Fe+2NaCl=FeCl 2+2Na; at 2.58 V: Ni+2NaCl=NiCl 2+2 Na. The first reaction serves to prime the negative sodium electrode but occurs at too low a voltage to be of use in providing useful capacity. By minimising the aluminium content more NaCl is released for the main reactions to improve the capacity of the cell. This, and further composition optimisation, have resulted in cells with specific energies in excess of 140 Wh kg -1, which equates to battery energies>100 Wh kg -1. The present production battery, as installed in a Mercedes Benz A class electric vehicle, gives a driving range of 205 km (128 miles) in city and hill climbing. The cells with improved capacity will extend the practical driving range to beyond 240 km (150 miles).

  10. American lifelines alliance efforts to improve electric power transmission reliability

    Science.gov (United States)

    Nishenko, S.P.; Savage, W.U.; Honegger, D.G.; McLane, T.R.; ,

    2002-01-01

    A study was performed on American Lifelines Alliance (ALA) efforts to improve electric power transmission reliability. ALA is a public-private partnership project, with the goal of reducing risks to lifelines from natural hazards and human threat events. The mechanism used by ALA for developing national guidelines for lifeline systems is dependent upon using existing Standards Developing Organizations (SDO) accredited by the American National Standards Institute (ANSI) as means to achieve national consensus.

  11. Studying and simulating transformer configuration to improve power quality

    Directory of Open Access Journals (Sweden)

    Oscar J. Peña Huaringa

    2011-07-01

    Full Text Available This paper presents a study and simulation of transformer configurations to improve power quality; it provides theoretical support based on the expansion of the Fourier series and analysis of symmetrical components. A test system was set up in the laboratory, taking measurements and checking configuration effectiveness in reducing the system’s harmonic content. The configurations were modelled with PSCAD / EMTDC software, using two 6 pulse rectifiers as test loads and two variable speed drives.

  12. Improving the Energy Efficiency of Pumped-Storage Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Artyukh, S. F., E-mail: artjuch@mail.ru [Kharkov Polytechnic Institute (Ukraine); Galat, V. V. [JSC “UkrHydroEnergo” (Ukraine); Kuz’min, V. V. [JSC “Interregional Electricity Association ELTA” (Ukraine); Chervonenko, I. I. [Kharkov Polytechnic Institute (Ukraine); Shakaryan, Yu. G.; Sokur, P. V. [JSC “R& D Center at Federal Grid Company of Unified Energy System” (Russian Federation)

    2015-01-15

    Possible ways to improve the energy efficiency of hydroelectric generating sets of pumped-storage power plants (PSPPs) are studied. The Kiev PSPP is used as an example to show how its generating sets can be upgraded. It is concluded based on studies conducted that synchronous motor-generators should be replaced with asynchronized motor-generators. The feasibility of changing over the turbine to variable-speed operation is shown.

  13. Improved grey-based approach for power demand forecasting

    Institute of Scientific and Technical Information of China (English)

    LIN Jia-mu; LIU Dan

    2006-01-01

    Grey theory is a multidisciplinary and generic theory to cope with systems of poor or deficient information. We proposed in this paper an improved grey method (GM) to overcome the disadvantages of the general GM(1,1). In the improved GM(1,1), a new background value formula is deduced and Markov-chain sign estimation is imbedded into the residual modification model. We tested the efficiency and accuracy of our model by applying it to the power demand forecasting in Taiwan. Experimental results demonstrate the new method has obviously a higher prediction accuracy than the general model.

  14. Improving automated load flexibility of nuclear power plants with ALFC

    Energy Technology Data Exchange (ETDEWEB)

    Kuhn, Andreas [AREVA GmbH, Karlstein (Germany). Plant Control/Training; Klaus, Peter [E.ON NPP Isar 2, Essenbach (Germany). Plant Operation/Production Engineering

    2016-07-01

    In several German and Swiss Nuclear Power Plants with Pressurized Water Reactor (PWR) the control of the reactor power was and will be improved in order to be able to support the energy transition with increasing volatile renewable energy in the grid by flexible load operation according to the need of the load dispatcher (power system stability). Especially regarding the mentioned German NPPs with a nominal electric power of approx. 1,500 MW, the general objectives are the main automated grid relevant operation modes. The new possibilities of digital I and C (as TELEPERM {sup registered} XS) enable the automation of the operating modes provided that manual support is no longer necessary. These possibilities were and will be implemented by AREVA within the ALFC-projects. Manifold adaption algorithms to the reactor physical variations during the nuclear load cycle enable a precise control of the axial power density distribution and of the reactivity management in the reactor core. Finally this is the basis for a highly automated load flexibility with the parallel respect and surveillance of the operational limits of a PWR.

  15. Final Deliverable W6, D6.4: Coal power plants with carbon capture and storage – A sustainability assessment

    NARCIS (Netherlands)

    Ramirez, C.A.; Schakel, W.B.; Wood, R.; Grytli, T.

    2013-01-01

    Carbon Capture and Storage (CCS) is increasingly gaining attention as a strategy for the abatement of greenhouse gas (GHG) emissions. CCS includes the capture of CO2 emissions from electricity generation plants and/or industrial processes, its transport (by pipeline or ships) and sequestration in un

  16. Final Deliverable W6, D6.4: Coal power plants with carbon capture and storage – A sustainability assessment

    NARCIS (Netherlands)

    Ramirez, C.A.|info:eu-repo/dai/nl/284852414; Schakel, W.B.|info:eu-repo/dai/nl/369280784; Wood, R.; Grytli, T.

    2013-01-01

    Carbon Capture and Storage (CCS) is increasingly gaining attention as a strategy for the abatement of greenhouse gas (GHG) emissions. CCS includes the capture of CO2 emissions from electricity generation plants and/or industrial processes, its transport (by pipeline or ships) and sequestration in un

  17. The Improved Power of the Central Lobe in the Beam Combination and High Power Output

    Institute of Scientific and Technical Information of China (English)

    LIU Hou-Kang; WEI Yun-Rong; DONG Jing-Xing; LOU Qi-Hong; XUE Yu-Hao; LI Zhen; HE Bing; ZHOU Jun; DING Ya-Qian; JIAO Meng-Li; LIU Chi; QI Yun-Feng

    2012-01-01

    In order to increase the power fraction of the central lobe in the coherent beam combination of lasers in an array,the effects of the distance factor of near-field distribution on far-field interference patterns are calculated and demonstrated experimentally.An improved beam array of interwoven distribution is demonstrated to enable the power in the central lobe to reach 41%.An optimized mirror array is carefully designed to obtain a high duty ratio,which is up to 53.3% at a high power level.By using these optimized methods and designs,the passive phase locking of eight Yb-doped fiber amplifiers with ring cavities are obtained,and a pleasing interference pattern with 87% visibility is observed.The maximum coherent output power of the system is up to 1066 W.%In order to increase the power fraction of the central lobe in the coherent beam combination of lasers in an array, the effects of the distance factor of near-field distribution on far-field interference patterns are calculated and demonstrated experimentally. An improved beam array of interwoven distribution is demonstrated to enable the power in the central lobe to reach 41%. An optimized mirror array is carefully designed to obtain a high duty ratio, which is up to 53.3% at a high power level. By using these optimized methods and designs, the passive phase locking of eight Yb-doped fiber amplifiers with ring cavities are obtained, and a pleasing interference pattern with 87% visibility is observed. The maximum coherent output power of the system is up to 1066 W.

  18. Technology Analysis of CO2 Capture and Storage in Firing Power Plant%火电厂CO2 CCS技术分析

    Institute of Scientific and Technical Information of China (English)

    胡月红

    2012-01-01

    After introducing the CO2 emission characteristics from firing power plant,this paper discussed two parts in both CO2 capture and storage,and put forward four main technological lines for CO2 capture in firing power plants.The paper also analyzed and compared the features and appliances of every capture measures,and pointed out some problems needed to be solved for using the existing capture methods to firing power plant in China.Finally it analyzed and summarized CO2 storage technology and comprehensive utilization.%介绍了火电厂CO2排放特点,将CO2减排技术分为捕集与封存两个部分进行讨论,提出了火电厂CO2捕集的4种主要技术路线;比较分析了几种主要捕集方法的技术特点和火力发电适用性,CO2应用于我国火电厂需解决的问题;综述了CO2的封存技术和综合利用。

  19. Low power smartdust receiver with novel applications and improvements of an RF power harvesting circuit

    Science.gov (United States)

    Salter, Thomas Steven, Jr.

    Smartdust is the evolution of wireless sensor networks to cubic centimeter dimensions or less. Smartdust systems have advantages in cost, flexibility, and rapid deployment that make them ideal for many military, medical, and industrial applications. This work addresses the limitations of prior works of research to provide sufficient lifetime and performance for Smartdust sensor networks through the design, fabrication and testing of a novel low power receiver for use in a Smartdust transceiver. Through the novel optimization of a multi-stage LNA design and novel application of a power matched Villard voltage doubler circuit, a 1.0 V, 1.6 mW low power On-Off Key (OOK) receiver operating at 2.2 GHz is fabricated using 0.13 um CMOS technology. To facilitate data transfer in adverse RF propagation environments (1/r3 loss), the chip receives a 1 Mbps data signal with a sensitivity of -90 dBm while consuming just 1.6 nJ/bit. The receiver operates without the addition of any external passives facilitating its application in Smartdust scale (cm 3) wireless sensor networks. This represents an order of magnitude decrease in power consumption over receiver designs of comparable sensitivity. In an effort to further extend the lifetime of the Smartdust transceiver, RF power harvesting is explored as a power source. The small scale of Smartdust sensor networks poses unique challenges in the design of RF power scavenging systems. To meet these challenges, novel design improvements to an RF power scavenging circuit integrated directly onto CMOS are presented. These improvements include a reduction in the threshold voltage of diode connected MOSFET and sources of circuit parasitics that are unique to integrated circuits. Utilizing these improvements, the voltage necessary to drive Smartdust circuitry (1 V) with a greater than 20% RF to DC conversion efficiency was generated from RF energy levels measured in the environment (66 uW). This represents better than double the RF to DC

  20. Power optimization and performance improvement for embedded Ethernet SOC

    Institute of Scientific and Technical Information of China (English)

    ZHENG Zhao-xia; ZOU Lian-ying; GAO Jun

    2008-01-01

    Information appliance is the combination of traditional home appliances and the internet technology. In this article, an Ethernet controller system-on-chip (SOC) solution for information appliances is presented. To achieve high performance, the embedded 8 bits 8051 micro control unit (MCU) is optimized by an independent instruction bus and a data bus. Besides, a two-stage pipeline feature is added. Compared with the existing 8051 core, the enhanced one-cycle MCU offers ten times improvement in instruction execution efficiency. Mean- while, the performance of media access control (MAC) circuit is greatly improved by adopting various techniques such as direct memory access (DMA) control, paging strategy, etc. To reduce the power consumption, clock gating, low power supply, and multi-working-clock are adopted. Moreover, to achieve rapid data communication in different clock frequency circuits, a simple ping-pong first in first out (FIFO) circuit is realized. The chip is implemented using TSMC 0.25 μm two-poly four-metal mixed signal complementary metal oxide semiconductor (CMOS) technology. Its die area is mm. The test results show that the maximum throughput of Ethernet packets can reach 7 Mb/s while the power consumption is rather low-the working current is just about 200 mA.

  1. An improved maximum power point tracking method for photovoltaic systems

    Energy Technology Data Exchange (ETDEWEB)

    Tafticht, T.; Agbossou, K.; Doumbia, M.L.; Cheriti, A. [Institut de recherche sur l' hydrogene, Departement de genie electrique et genie informatique, Universite du Quebec a Trois-Rivieres, C.P. 500, Trois-Rivieres (QC) (Canada)

    2008-07-15

    In most of the maximum power point tracking (MPPT) methods described currently in the literature, the optimal operation point of the photovoltaic (PV) systems is estimated by linear approximations. However these approximations can lead to less than optimal operating conditions and hence reduce considerably the performances of the PV system. This paper proposes a new approach to determine the maximum power point (MPP) based on measurements of the open-circuit voltage of the PV modules, and a nonlinear expression for the optimal operating voltage is developed based on this open-circuit voltage. The approach is thus a combination of the nonlinear and perturbation and observation (P and O) methods. The experimental results show that the approach improves clearly the tracking efficiency of the maximum power available at the output of the PV modules. The new method reduces the oscillations around the MPP, and increases the average efficiency of the MPPT obtained. The new MPPT method will deliver more power to any generic load or energy storage media. (author)

  2. Topping gas turbines improve steam power plant efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Lezuo, A. (Siemens AG, Erlangen (Germany, F.R.). KWU Group)

    An interesting option for improving the efficiency and output of an existing conventional steam power plant is to convert it into a combined steam-and-gas cycle power plant by adding a topping gas turbine. The investment involved is relatively low, the payback period is short, and the low specific fuel consumption makes it possible to save on overall running costs. At the same time, the amount of residue for disposal and also pollutant emissions are drastically reduced. This article describes the configuration of a fully-fired combined-cycle power plant and discusses thermodynamic design and efficiency, operational aspects, emissions and residues and investment and economic viability. Both coal-fired and gas or oil-fired steam power plants can be converted by adding a topping cycle and the investment cost is about 20% of the cost of a new plant with the same output rating as the plant to be converted. Conversion reduces pollutant emission and residues produced (SO{sub 2}, NO{sub x}, CO{sub 2}, dust, ash, gypsum, waste heat). 4 figs.

  3. Study of CO{sub 2} capture processes in power plants; Etude de procedes de captage du CO{sub 2} dans les centrales thermiques

    Energy Technology Data Exchange (ETDEWEB)

    Amann, J.M

    2007-12-15

    The aim of the present study is to assess and compare various processes aiming at recover CO{sub 2} from power plants fed with natural gas (NGCC) and pulverized coal (PC). These processes are post-combustion CO{sub 2} capture using chemical solvents, natural gas reforming for pre-combustion capture by methanol and oxy-fuel combustion with cryogenic recovery of CO{sub 2}. These processes were evaluated using the process software Aspen PlusTM to give some clues for choosing the best option for each type of power plant. With regard to post-combustion, an aqueous solution based on a mixture of amines (N-methyldiethanolamine (MDEA) and triethylene tetramine (TETA)) was developed. Measurements of absorption were carried out between 298 and 333 K in a Lewis cell. CO{sub 2} partial pressure at equilibrium, characteristic of the CO{sub 2} solubility in the solvent, was determined up to 393 K. The solvent performances were compared with respect to more conventional solvents such as MDEA and monoethanolamine (MEA). For oxy-fuel combustion, a recovery process, based on a cryogenic separation of the components of the flue gas, was developed and applied to power plants. The study showed that O{sub 2} purity acts on the CO{sub 2} concentration in the flue gas and thus on the performances of the recovery process. The last option is natural gas reforming with CO{sub 2} pre-combustion capture. Several configurations were assessed: air reforming and oxygen reforming, reforming pressure and dilution of the synthesis gas. The comparison of these various concepts suggests that, in the short and medium term, chemical absorption is the most interesting process for NGCC power plants. For CP power plants, oxy-combustion can be a very interesting option, as well as post-combustion capture by chemical solvents. (author)

  4. Capturing Thoughts, Capturing Minds?

    DEFF Research Database (Denmark)

    Nielsen, Janni

    2004-01-01

    Think Aloud is cost effective, promises access to the user's mind and is the applied usability technique. But 'keep talking' is difficult, besides, the multimodal interface is visual not verbal. Eye-tracking seems to get around the verbalisation problem. It captures the visual focus of attention...

  5. Development and testing of improved statistical wind power forecasting methods.

    Energy Technology Data Exchange (ETDEWEB)

    Mendes, J.; Bessa, R.J.; Keko, H.; Sumaili, J.; Miranda, V.; Ferreira, C.; Gama, J.; Botterud, A.; Zhou, Z.; Wang, J. (Decision and Information Sciences); (INESC Porto)

    2011-12-06

    Wind power forecasting (WPF) provides important inputs to power system operators and electricity market participants. It is therefore not surprising that WPF has attracted increasing interest within the electric power industry. In this report, we document our research on improving statistical WPF algorithms for point, uncertainty, and ramp forecasting. Below, we provide a brief introduction to the research presented in the following chapters. For a detailed overview of the state-of-the-art in wind power forecasting, we refer to [1]. Our related work on the application of WPF in operational decisions is documented in [2]. Point forecasts of wind power are highly dependent on the training criteria used in the statistical algorithms that are used to convert weather forecasts and observational data to a power forecast. In Chapter 2, we explore the application of information theoretic learning (ITL) as opposed to the classical minimum square error (MSE) criterion for point forecasting. In contrast to the MSE criterion, ITL criteria do not assume a Gaussian distribution of the forecasting errors. We investigate to what extent ITL criteria yield better results. In addition, we analyze time-adaptive training algorithms and how they enable WPF algorithms to cope with non-stationary data and, thus, to adapt to new situations without requiring additional offline training of the model. We test the new point forecasting algorithms on two wind farms located in the U.S. Midwest. Although there have been advancements in deterministic WPF, a single-valued forecast cannot provide information on the dispersion of observations around the predicted value. We argue that it is essential to generate, together with (or as an alternative to) point forecasts, a representation of the wind power uncertainty. Wind power uncertainty representation can take the form of probabilistic forecasts (e.g., probability density function, quantiles), risk indices (e.g., prediction risk index) or scenarios

  6. 电厂二氧化碳捕集分离技术研究综述%A Review of the Research into Carbon Capture and Sequestration Technologies for Power Plants

    Institute of Scientific and Technical Information of China (English)

    赵毅; 张自丽

    2012-01-01

    One of the important missions for global carbon dioxide reduction is controlling the carbon dioxide emissions from power plants.Carbon capture and storage,a hot spot of the research among carbon dioxide reduction technologies,include physical adsorption/absorption,chemical absorption,physico-chemical absorption, membrane technology,biotechnology,and etc.,of which physical adsorption/absorption and chemical absorption are the main ones for carbon capture in power plants.To develop highly selective and efficient absorbents and capture processes,to improve energy efficiency,and to rationally arrange flue gas decarbonisation facilities are the challenges of carbon capture technologies for power plants.%电厂二氧化碳捕集与封存是二氧化碳减排措施研究热点,也是全球二氧化碳减排的重要任务之一,可分为物理吸附/吸收、化学吸收、物理-化学吸收、膜技术及生物技术等。其中物理吸附/吸收、化学吸收为电厂二氧化碳捕集主流技术。开发具有高选择性、高效率吸收剂及捕集技术,提高能源利用效率,合理布置尾部烟气脱碳处理设施是电厂二氧化碳捕集技术面临的挑战。

  7. Experimental verification of improved depth-dose distribution using hyper-thermal neutron incidence in neutron capture therapy

    Science.gov (United States)

    Sakurai, Yoshinori; Kobayashi, Tooru

    2001-01-01

    We have proposed the utilization of `hyper-thermal neutrons' for neutron capture therapy (NCT) from the viewpoint of the improvement in the dose distribution in a human body. In order to verify the improved depth-dose distribution due to hyper-thermal neutron incidence, two experiments were carried out using a test-type hyper-thermal neutron generator at a thermal neutron irradiation field in Kyoto University Reactor (KUR), which is actually utilized for NCT clinical irradiation. From the free-in-air experiment for the spectrum-shift characteristics, it was confirmed that the hyper-thermal neutrons of approximately 860 K at maximum could be obtained by the generator. From the phantom experiment, the improvement effect and the controllability for the depth-dose distribution were confirmed. For example, it was found that the relative neutron depth-dose distribution was about 1 cm improved with the 860 K hyper-thermal neutron incidence, compared to the normal thermal neutron incidence.

  8. Experimental verification of improved depth-dose distribution using hyper-thermal neutron incidence in neutron capture therapy.

    Science.gov (United States)

    Sakurai, Y; Kobayashi, T

    2001-01-01

    We have proposed the utilization of 'hyper-thermal neutrons' for neutron capture therapy (NCT) from the viewpoint of the improvement in the dose distribution in a human body. In order to verify the improved depth-dose distribution due to hyper-thermal neutron incidence, two experiments were carried out using a test-type hyper-thermal neutron generator at a thermal neutron irradiation field in Kyoto University Reactor (KUR), which is actually utilized for NCT clinical irradiation. From the free-in-air experiment for the spectrum-shift characteristics, it was confirmed that the hyper-thermal neutrons of approximately 860 K at maximum could be obtained by the generator. From the phantom experiment, the improvement effect and the controllability for the depth-dose distribution were confirmed. For example, it was found that the relative neutron depth-dose distribution was about 1 cm improved with the 860 K hyper-thermal neutron incidence, compared to the normal thermal neutron incidence.

  9. Improved Method for PD-Quantification in Power Cables

    DEFF Research Database (Denmark)

    Holbøll, Joachim T.; Villefrance, Rasmus; Henriksen, Mogens

    1999-01-01

    n this paper, a method is described for improved quantification of partial discharges(PD) in power cables. The method is suitable for PD-detection and location systems in the MHz-range, where pulse attenuation and distortion along the cable cannot be neglected. The system transfer function...... was calculated and measured in order to form basis for magnitude calculation after each measurements. --- Limitations and capabilities of the method will be discussed and related to relevant field applications of high frequent PD-measurements. --- Methods for increased signal/noise ratio are easily implemented...

  10. Improved Discontinuity-capturing Finite Element Techniques for Reaction Effects in Turbulence Computation

    Science.gov (United States)

    Corsini, A.; Rispoli, F.; Santoriello, A.; Tezduyar, T. E.

    2006-09-01

    Recent advances in turbulence modeling brought more and more sophisticated turbulence closures (e.g. k-ɛ, k-ɛ - v 2- f, Second Moment Closures), where the governing equations for the model parameters involve advection, diffusion and reaction terms. Numerical instabilities can be generated by the dominant advection or reaction terms. Classical stabilized formulations such as the Streamline Upwind/Petrov Galerkin (SUPG) formulation (Brook and Hughes, comput methods Appl Mech Eng 32:199 255, 1982; Hughes and Tezduyar, comput methods Appl Mech Eng 45: 217 284, 1984) are very well suited for preventing the numerical instabilities generated by the dominant advection terms. A different stabilization however is needed for instabilities due to the dominant reaction terms. An additional stabilization term, called the diffusion for reaction-dominated (DRD) term, was introduced by Tezduyar and Park (comput methods Appl Mech Eng 59:307 325, 1986) for that purpose and improves the SUPG performance. In recent years a new class of variational multi-scale (VMS) stabilization (Hughes, comput methods Appl Mech Eng 127:387 401, 1995) has been introduced, and this approach, in principle, can deal with advection diffusion reaction equations. However, it was pointed out in Hanke (comput methods Appl Mech Eng 191:2925 2947) that this class of methods also need some improvement in the presence of high reaction rates. In this work we show the benefits of using the DRD operator to enhance the core stabilization techniques such as the SUPG and VMS formulations. We also propose a new operator called the DRDJ (DRD with the local variation jump) term, targeting the reduction of numerical oscillations in the presence of both high reaction rates and sharp solution gradients. The methods are evaluated in the context of two stabilized methods: the classical SUPG formulation and a recently-developed VMS formulation called the V-SGS (Corsini et al. comput methods Appl Mech Eng 194:4797 4823, 2005

  11. An Improved Droop Control Strategy for Reactive Power Sharing in Islanded Microgrid

    DEFF Research Database (Denmark)

    Han, Hua; Liu, Yao; Sun, Yao

    2015-01-01

    For microgrid in islanded operation, due to the effects of mismatched line impedance, the reactive power could not be shared accurately with the conventional droop method. To improve the reactive power sharing accuracy, this paper proposes an improved droop control method. The proposed method...... and reactive power, improve the power quality of the microgrid, and also have a good dynamic performance....

  12. Injection deep level transient spectroscopy: An improved method for measuring capture rates of hot carriers in semiconductors

    Science.gov (United States)

    Fleming, R. M.; Seager, C. H.; Lang, D. V.; Campbell, J. M.

    2015-07-01

    An improved method for measuring the cross sections for carrier trapping at defects in semiconductors is described. This method, a variation of deep level transient spectroscopy (DLTS) used with bipolar transistors, is applied to hot carrier trapping at vacancy-oxygen, carbon-oxygen, and three charge states of divacancy centers (V2) in n- and p-type silicon. Unlike standard DLTS, we fill traps by injecting carriers into the depletion region of a bipolar transistor diode using a pulse of forward bias current applied to the adjacent diode. We show that this technique is capable of accurately measuring a wide range of capture cross sections at varying electric fields due to the control of the carrier density it provides. Because this technique can be applied to a variety of carrier energy distributions, it should be valuable in modeling the effect of radiation-induced generation-recombination currents in bipolar devices.

  13. EVALUATION OF SOLID SORBENTS AS A RETROFIT TECHNOLOGY FOR CO2 CAPTURE FROM COAL-FIRED POWER PLANTS

    Energy Technology Data Exchange (ETDEWEB)

    Holly Krutka; Sharon Sjostrom

    2011-07-31

    Through a U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) funded cooperative agreement DE-NT0005649, ADA Environmental Solutions (ADA) has begun evaluating the use of solid sorbents for CO{sub 2} capture. The project objective was to address the viability and accelerate development of a solid-based CO{sub 2} capture technology. To meet this objective, initial evaluations of sorbents and the process/equipment were completed. First the sorbents were evaluated using a temperature swing adsorption process at the laboratory scale in a fixed-bed apparatus. A slipstream reactor designed to treat flue gas produced by coal-fired generation of nominally 1 kWe was designed and constructed, which was used to evaluate the most promising materials on a more meaningful scale using actual flue gas. In a concurrent effort, commercial-scale processes and equipment options were also evaluated for their applicability to sorbent-based CO{sub 2} capture. A cost analysis was completed that can be used to direct future technology development efforts. ADA completed an extensive sorbent screening program funded primarily through this project, DOE NETL cooperative agreement DE-NT0005649, with support from the Electric Power Research Institute (EPRI) and other industry participants. Laboratory screening tests were completed on simulated and actual flue gas using simulated flue gas and an automated fixed bed system. The following types and quantities of sorbents were evaluated: 87 supported amines; 31 carbon based materials; 6 zeolites; 7 supported carbonates (evaluated under separate funding); and 10 hydrotalcites. Sorbent evaluations were conducted to characterize materials and down-select promising candidates for further testing at the slipstream scale. More than half of the materials evaluated during this program were supported amines. Based on the laboratory screening four supported amine sorbents were selected for evaluation at the 1 kW scale at two different

  14. Evaluation of Solid Sorbents As A Retrofit Technology for CO{sub 2} Capture from Coal-Fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Krutka, Holly; Sjostrom, Sharon

    2011-07-31

    Through a U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) funded cooperative agreement DE-NT0005649, ADA Environmental Solutions (ADA) has begun evaluating the use of solid sorbents for CO{sub 2} capture. The project objective was to address the viability and accelerate development of a solid-based CO{sub 2} capture technology. To meet this objective, initial evaluations of sorbents and the process / equipment were completed. First the sorbents were evaluated using a temperature swing adsorption process at the laboratory scale in a fixed-bed apparatus. A slipstream reactor designed to treat flue gas produced by coal-fired generation of nominally 1 kWe was designed and constructed, which was used to evaluate the most promising materials on a more meaningful scale using actual flue gas. In a concurrent effort, commercial-scale processes and equipment options were also evaluated for their applicability to sorbent-based CO{sub 2} capture. A cost analysis was completed that can be used to direct future technology development efforts. ADA completed an extensive sorbent screening program funded primarily through this project, DOE NETL cooperative agreement DE-NT0005649, with support from the Electric Power Research Institute (EPRI) and other industry participants. Laboratory screening tests were completed on simulated and actual flue gas using simulated flue gas and an automated fixed bed system. The following types and quantities of sorbents were evaluated: 87 supported amines, 31 carbon based materials, 6 zeolites, 7 supported carbonates (evaluated under separate funding), 10 hydrotalcites. Sorbent evaluations were conducted to characterize materials and down-select promising candidates for further testing at the slipstream scale. More than half of the materials evaluated during this program were supported amines. Based on the laboratory screening four supported amine sorbents were selected for evaluation at the 1 kW scale at two different

  15. EVALUATION OF SOLID SORBENTS AS A RETROFIT TECHNOLOGY FOR CO2 CAPTURE FROM COAL-FIRED POWER PLANTS

    Energy Technology Data Exchange (ETDEWEB)

    Holly Krutka; Sharon Sjostrom

    2011-07-31

    Through a U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) funded cooperative agreement DE-NT0005649, ADA Environmental Solutions (ADA) has begun evaluating the use of solid sorbents for CO{sub 2} capture. The project objective was to address the viability and accelerate development of a solid-based CO{sub 2} capture technology. To meet this objective, initial evaluations of sorbents and the process/equipment were completed. First the sorbents were evaluated using a temperature swing adsorption process at the laboratory scale in a fixed-bed apparatus. A slipstream reactor designed to treat flue gas produced by coal-fired generation of nominally 1 kWe was designed and constructed, which was used to evaluate the most promising materials on a more meaningful scale using actual flue gas. In a concurrent effort, commercial-scale processes and equipment options were also evaluated for their applicability to sorbent-based CO{sub 2} capture. A cost analysis was completed that can be used to direct future technology development efforts. ADA completed an extensive sorbent screening program funded primarily through this project, DOE NETL cooperative agreement DE-NT0005649, with support from the Electric Power Research Institute (EPRI) and other industry participants. Laboratory screening tests were completed on simulated and actual flue gas using simulated flue gas and an automated fixed bed system. The following types and quantities of sorbents were evaluated: 87 supported amines; 31 carbon based materials; 6 zeolites; 7 supported carbonates (evaluated under separate funding); and 10 hydrotalcites. Sorbent evaluations were conducted to characterize materials and down-select promising candidates for further testing at the slipstream scale. More than half of the materials evaluated during this program were supported amines. Based on the laboratory screening four supported amine sorbents were selected for evaluation at the 1 kW scale at two different

  16. A research needs assessment for the capture, utilization and disposal of carbon dioxide from fossil fuel-fired power plants. Volume 2, Topical reports: Final report

    Energy Technology Data Exchange (ETDEWEB)

    1993-07-01

    This study, identifies and assesses system approaches in order to prioritize research needs for the capture and non-atmospheric sequestering of a significant portion of the carbon dioxide (CO{sub 2}) emitted from fossil fuel-fired electric power plants (US power plants presently produce about 7% of the world`s CO{sub 2} emissions). The study considers capture technologies applicable either to existing plants or to those that optimistically might be demonstrated on a commercial scale over the next twenty years. The research needs that have high priority in establishing the technical, environmental, and economic feasibility of large-scale capture and disposal of CO{sub 2} from electric power plants are:(1) survey and assess the capacity, cost, and location of potential depleted gas and oil wells that are suitable CO{sub 2} repositories (with the cooperation of the oil and gas industry); (2) conduct research on the feasibility of ocean disposal, with objectives of determining the cost, residence time, and environmental effects for different methods of CO{sub 2} injection; (3) perform an in-depth survey of knowledge concerning the feasibility of using deep, confined aquifers for disposal and, if feasible, identify potential disposal locations (with the cooperation of the oil and gas industry); (4) evaluate, on a common basis, system and design alternatives for integration of CO{sub 2} capture systems with emerging and advanced technologies for power generation; and prepare a conceptual design, an analysis of barrier issues, and a preliminary cost estimate for pipeline networks necessary to transport a significant portion of the CO{sub 2} to potentially feasible disposal locations.

  17. Joy and challenges in improving chronic illness care: capturing daily experiences of academic primary care teams.

    Science.gov (United States)

    Johnson, Julie K; Woods, Donna M; Stevens, David P; Bowen, Judith L; Provost, Lloyd P; Sixta, Connie S; Wagner, Ed H

    2010-09-01

    Two chronic care collaboratives (The National Collaborative and the California Collaborative) were convened to facilitate implementing the chronic care model (CCM) in academic medical centers and into post-graduate medical education. We developed and implemented an electronic team survey (ETS) to elicit, in real-time, team member's experiences in caring for people with chronic illness and the effect of the Collaborative on teams and teamwork. The ETS is a qualitative survey based on Electronic Event Sampling Methodology. It is designed to collect meaningful information about daily experience and any event that might influence team members' daily work and subsequent outcomes. Forty-one residency programs from 37 teaching hospitals participated in the collaboratives and comprised faculty and resident physicians, nurses, and administrative staff. Each team member participating in the collaboratives received an e-mail with directions to complete the ETS for four weeks during 2006 (the National Collaborative) and 2007 (the California Collaborative). At the team level, the response rate to the ETS was 87% with team members submitting 1,145 narrative entries. Six key themes emerged from the analysis, which were consistent across all sites. Among teams that achieved better clinical outcomes on Collaborative clinical indicators, an additional key theme emerged: professional work satisfaction, or "Joy in Work". In contrast, among teams that performed lower in collaborative measures, two key themes emerged that reflected the effect of providing care in difficult institutional environments-"lack of professional satisfaction" and awareness of "system failures". The ETS provided a unique perspective into team performance and the day-to-day challenges and opportunities in chronic illness care. Further research is needed to explore systematic approaches to integrating the results from this study into the design of improvement efforts for clinical teams.

  18. Improving the efficiency of solar photovoltaic power system

    Science.gov (United States)

    Aribisala, Henry A.

    As the local and national clamor for foreign energy independent United States continues to grow unabated; renewable energy has been receiving increased focus and it's widely believed that it's not only the answer to ever increasing demand for energy in this country, but also the environmentally friendly means of meeting such demand. During the spring of 2010, I was involved with a 5KW solar power system design project; the project involved designing and building solar panels and associated accessories like the solar array mounts and Solar Inverter system. One of the key issues we ran into during the initial stage of the project was how to select efficient solar cells for panel building at a reasonable cost. While we were able to purchase good solar cells within our allocated budget, the issue of design for efficiency was not fully understood , not just in the contest of solar cells performance , but also in the overall system efficiency of the whole solar power system, hence the door was opened for this thesis. My thesis explored and expanded beyond the scope of the aforementioned project to research different avenues for improving the efficiency of solar photo-voltaic power system from the solar cell level to the solar array mounting, array tracking and DC-AC inversion system techniques.

  19. Improved Measurements of the CMB Power Spectrum with ACBAR

    CERN Document Server

    Kuo, C L; Bock, J J; Bond, J R; Contaldi, C R; Daub, M D; Goldstein, J H; Holzapfel, W L; Lange, A E; Lueker, M; Newcomb, M; Peterson, J B; Reichardt, C; Ruhl, J; Runyan, M C; Staniszweski, Z

    2006-01-01

    We report improved measurements of temperature anisotropies in the cosmic microwave background (CMB) radiation made with the Arcminute Cosmology Bolometer Array Receiver (ACBAR). In this paper, we use a new analysis technique and include 30% more data from the 2001 and 2002 observing seasons than the first release to derive a new set of band-power measurements with significantly smaller uncertainties. The planet-based calibration used previously has been replaced by comparing the flux of RCW38 as measured by ACBAR and BOOMERANG to transfer the WMAP-based BOOMERANG calibration to ACBAR. The resulting power spectrum is consistent with the theoretical predictions for a spatially flat, dark energy dominated LCDM cosmology including the effects of gravitational lensing. Despite the exponential damping on small angular scales, the primary CMB fluctuations are detected with a signal-to-noise ratio of greater than 4 up to multipoles of l=2000. This increase in the precision of the fine-scale CMB power spectrum leads ...

  20. Improvement of Power Quality Using a Hybrid Interline UPQC

    Directory of Open Access Journals (Sweden)

    M.K.Elango

    2014-05-01

    Full Text Available This paper proposed the reduced rating star connected transformer based interline unified power quality conditioner. This work comprises of unified power quality conditioner connected between the two feeders, star connected transformer and LC filter. This hybrid approach significantly improves the performance of UPQC under unbalance source voltage condition. The UPQC adopted to compensate current and voltage-quality problems of sensitive loads and suppressing the load current harmonics under distorted supply conditions. The series converter control strategy is based on the fuzzy-logic controller. The extensive simulation results have carried out in MATLAB/Simulink environment power system blockset toolboxes. From the results it has shown that hybrid interline UPQC achieves superior capability of mitigating the effects of voltage sag/swell and suppressing the load current harmonics, phase current harmonics and neutral current under distorted supply conditions. To validate the results produced by the proposed method, it is compared with the conventional UPQC method and better results obtained from the hybrid approach.

  1. ComfortPower - System improvements and long-term evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Silversand, Fredrik [Catator AB, Lund (Sweden)

    2011-11-15

    Catator has previously developed a novel heating system abbreviated ComfortPower in a RandD-programme supported by Catator, Swedish Gas Centre (SGC), Swedish Defence Materiel Administration (FMV), Skanska, Nibe and Alfa Laval. The ComfortPower unit comprises a multi fuel reformer system tied to a high-temperature polymer electrolyte fuel cell (HT-PEM) and a heat pump system. Since the residual heat from the fuel cell system can be utilized in a very effective way, it is possible to reach high thermal efficiencies. Indeed, the thermal efficiency in the unit has previously been shown to reach values as high as 175 - 200 % based on the lower heating value of the fuel. In addition to heat, ComfortPower can supply comfort cooling and surplus electricity. This project phase has focused on the following elements: 1. System improvements to further enhance the efficiency with existing fuel cell (HT-PEM). 2. System simplifications (e.g. DC-compressor system) to manage issues with start-up currents. 3. Tests with biogas qualities (various levels of CO{sub 2}) and biogas/air. 4. Long-term test with biogas quality (upgraded biogas). 5. Additional tests with liquid fuels (alcohols and diesel). 6. Map the need for cooling and heating in various applications. 7. Investigate how ComfortPower can reduce the primary energy consumption and reduce the environmental impact. 8. Study the possibility with a SOFC-based system with internal reforming. It was found that the Optiformer technology can be used to derive a suitable reformate gas for the HT-PEM unit from a wide range of fuels. Even if operation with fuel gases is the natural choice in most cases, it is possible also to use alcohols and other liquid fuels (e.g. in Campus applications). The heat pump system was equipped with a 24 V DC-compressor provided by Nibe. The compressor could be directly powered by the accumulator system and start-up currents, harmful to the inverter, could be avoided. Some improvements were made on the

  2. Performance of improved magnetostrictive vibrational power generator, simple and high power output for practical applications

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, Toshiyuki, E-mail: ueno@ec.t.kanazawa-u.ac.jp [Kanazawa University, Kakuma-machi, Kanazawa-city, Ishikawa 920-1192 (Japan)

    2015-05-07

    Vibration based power generation technology is utilized effectively in various fields. Author has invented novel vibrational power generation device using magnetostrictive material. The device is based on parallel beam structure consisting of a rod of iron-gallium alloy wound with coil and yoke accompanied with permanent magnet. When bending force is applied on the tip of the device, the magnetization inside the rod varies with induced stress due to the inverse magnetostrictive effect. In vibration, the time variation of the magnetization generates voltage on the wound coil. The magnetostrictive type is advantageous over conventional such using piezoelectric or moving magnet types in high efficiency and high robustness, and low electrical impedance. Here, author has established device configuration, simple, rigid, and high power output endurable for practical applications. In addition, the improved device is lower cost using less volume of Fe-Ga and permanent magnet compared to our conventional, and its assembly by soldering is easy and fast suitable for mass production. Average power of 3 mW/cm{sup 3} under resonant vibration of 212 Hz and 1.2 G was obtained in miniature prototype using Fe-Ga rod of 2 × 0.5× 7 mm{sup 3}. Furthermore, the damping effect was observed, which demonstrates high energy conversion of the generator.

  3. CAN THE POWER BALANCE® BRACELET IMPROVE BALANCE, FLEXIBILITY, STRENGTH, AND POWER?

    Directory of Open Access Journals (Sweden)

    John Porcari

    2011-03-01

    Full Text Available Athletes are constantly searching for something that will give them a competitive edge. Performance jewelry is one of the latest products on the market designed to improve athletic performance. The most common claims are that wearing this performance jewelry will improve flexibility, balance, and strength. There is considerable marketing of these products, including testimonial evidence by high profile athletes, in support of the purported benefits. In demonstrations designed to validate the performance enhancing benefits of these products, however, companies typically conduct the testing in the following sequence: The first trial is done without the bracelet on and the second trial is performed with the bracelet on. Invariably, subjects perform better on the second trial. This brings into questions whether the improvement on the second trial is due to 1 a benefit of the bracelet, 2 the fact the subjects were warmed-up (Maud et al., 2006a; 2006b, 3 subjects being habituated to the task (Benson and Friedman, 1996; Wright et al., 2009, or 4 a placebo effect (Beedie and Foad, 2009.One of the most popular performance enhancing bracelets currently on the market is sold by Power Balance® (www.powerbalance.com. The Power Balance® bracelet has two dime-sized holograms; one on either side of the bracelet. The holograms within the Power Balance® bracelet are designed to "resonate with and respond to the natural energy field of the body". This purportedly improves flexibility, balance, and strength. To our knowledge, no randomized, double- blind, placebo trials have ever been conducted evaluating the validity of these claims. Thus, the purpose of this study was to evaluate whether wearing of the Power Balance® bracelet can improve trunk flexibility, balance, strength, and lower body power.Forty-two NCAA Division III athletes (22M: 20.1 ± 1.4 years, 1.82 ± 6.4 m, 82.0 ± 12.6 kg; 20F: 19.5 ± 1.3 years, 1.66 ± 6. 8 m, 63.2 ± 8.1 kg completed four

  4. Application of artificial neural networks to improve power transfer ...

    African Journals Online (AJOL)

    user

    the maximum power transfer in power systems and the proposed ANN technique is ... the power transfer capability according to the system operating condition. ..... guidelines for a priori knowledge of which ANN architecture would perform the.

  5. Method and apparatus for improved high power impulse magnetron sputtering

    Science.gov (United States)

    Anders, Andre

    2013-11-05

    A high power impulse magnetron sputtering apparatus and method using a vacuum chamber with a magnetron target and a substrate positioned in the vacuum chamber. A field coil being positioned between the magnetron target and substrate, and a pulsed power supply and/or a coil bias power supply connected to the field coil. The pulsed power supply connected to the field coil, and the pulsed power supply outputting power pulse widths of greater that 100 .mu.s.

  6. Improved Differential Evolution for Combined Heat and Power Economic Dispatch

    Science.gov (United States)

    Jena, C.; Basu, M.; Panigrahi, C. K.

    2016-04-01

    This paper presents an improved differential evolution to solve non-smooth non-convex combined heat and power economic dispatch (CHPED) problem. Valve-point loading and prohibited operating zones of conventional thermal generators are taken into account. Differential evolution (DE) exploits the differences of randomly sampled pairs of objective vectors for its mutation process. Consequently the variation between vectors will outfit the objective function toward the optimization process and therefore provides efficient global optimization capability. However, although DE is shown to be precise, fast as well as robust, its search efficiency will be impaired during solution process with fast descending diversity of population. This paper proposes Gaussian random variable instead of scaling factor which improves search efficiency. The effectiveness of the proposed method has been verified on four test systems. The results of the proposed approach are compared with those obtained by other evolutionary methods. It is found that the proposed improved differential evolution based approach is able to provide better solution.

  7. CFD modelling of longwall goaf gas flow to improve gas capture and prevent goaf self-heating

    Institute of Scientific and Technical Information of China (English)

    REN Ting-xiang

    2009-01-01

    CFD models have been developed to investigate the Iongwall goaf gas flow pat-terns under different mining and geological control conditions. The Iongwall goaf was treated as porous regions and gas flow was modelled as a momentum sink added to the momentum equation. Gas desorption from the caved goaf and destressed coal seams within the mining disturbed area was modelled as additional mass sources in the continu-ity equation. These CFD models were developed according to specific Iongwall layouts and calibrated against field monitoring data. Two case studies were presented demon-strating the application of CFD modelling of goaf gas flow characteristics for improved goaf gas capture and the reduction of oxygen ingress into the goaf areas for self-heating pre-vention. Results from the case studies indicate that the optimum goaf drainage strategy would be a combination of shallow (near the face) and deep holes to improve the overall drainage efficiency and gas purity. For gassy longwall faces retreating against the seam dip, it is recommended to conduct cross-measure roof hole drainage targeting the fractured zones overlying the return comer, rather than high capacity surface goaf drainage deep in the goaf.

  8. A Techno-Economic Assessment of Hybrid Cooling Systems for Coal- and Natural-Gas-Fired Power Plants with and without Carbon Capture and Storage.

    Science.gov (United States)

    Zhai, Haibo; Rubin, Edward S

    2016-04-05

    Advanced cooling systems can be deployed to enhance the resilience of thermoelectric power generation systems. This study developed and applied a new power plant modeling option for a hybrid cooling system at coal- or natural-gas-fired power plants with and without amine-based carbon capture and storage (CCS) systems. The results of the plant-level analyses show that the performance and cost of hybrid cooling systems are affected by a range of environmental, technical, and economic parameters. In general, when hot periods last the entire summer, the wet unit of a hybrid cooling system needs to share about 30% of the total plant cooling load in order to minimize the overall system cost. CCS deployment can lead to a significant increase in the water use of hybrid cooling systems, depending on the level of CO2 capture. Compared to wet cooling systems, widespread applications of hybrid cooling systems can substantially reduce water use in the electric power sector with only a moderate increase in the plant-level cost of electricity generation.

  9. Trunk Flexibility Improvement in Response to Powered Assisted Exercise

    Directory of Open Access Journals (Sweden)

    B.S. Bains

    2016-07-01

    Full Text Available Background study: Flexibility in human spine has always plays an important role in dexterity and seamless ambulatory activities. When optimum range is not maintained by the trunk column, due to lack of flexibility, the posture gets affected resulting in reduce trunk rotation flexibility and mobility hence loss of complete trunk rotation. Objective: The purpose of this study is to determine the effect of Shapemaster Power Assisted Exercise Equipment (SPAEE on trunk flexibility. Methodology: Twenty healthy individual ages between 40 to 60 years were randomly divided into control and exercise groups. Shapemaster exercise program performed two times per week for 5 weeks and 45 minutes per session. Before and after 10 sessions of Shapemaster exercise protocol, Seated trunk rotation test was used to measure trunk flexibility. Results: Repeated measurement ANOVA were used to analysis data between groups. The results of this study illustrated that after 10th sessions trunk flexibility significantly improved (F (1.0, 18 = 11.732, p < 0.003. Conclusion: In conclusion results were determined that SPAEE is safe and it did effectively enhance flexibility among individual healthy adults. Keyword: Shapemaster Power Assisted Exercise Equipment (SPAEE, Trunk Flexibility, Healthy individual

  10. Improved technical specifications and related improvements to safety in commercial Nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, D.R.; Demitrack, T.; Schiele, R.; Jones, J.C. [EXCEL Services Corporation, 11921 Rockville Pike, Suite 100, Rockville, MD 20852 (United States)]. e-mail: donaldh@excelservices.com

    2004-07-01

    Many of the commercial nuclear power plants in the United States (US) have been converting a portion of the plant operating license known as the Technical Specifications (TS) in accordance with a document published by the US Nuclear Regulatory Commission (NRC). The TS prescribe commercial nuclear power plant operating requirements. There are several types of nuclear power plants in the US, based on the technology of different vendors, and there is an NRC document that supports each of the five different vendor designs. The NRC documents are known as the Improved Standard Technical Specifications (ISTS) and are contained in a separate document (NUREG series) for each one of the designs. EXCEL Services Corporation (hereinafter EXCEL) has played a major role in the development of the ISTS and in the development, licensing, and implementation of the plant specific Improved Technical Specifications (ITS) (which is based on the ISTS) for the commercial nuclear power plants in the US that have elected to make this conversion. There are currently 103 operating commercial nuclear power plants in the US and 68 of them have successfully completed the conversion to the ITS and are now operating in accordance with their plant specific ITS. The ISTS is focused mainly on safety by ensuring the commercial nuclear reactors can safely shut down and mitigate the consequences of any postulated transient and accident. It accomplishes this function by including requirements directly associated with safety in a document structured systematically and taking into account some key human factors and technical initiatives. This paper discusses the ISTS including its format, content, and detail, the history of the ISTS, the ITS development, licensing, and implementation process, the safety improvements resulting from a plant conversion to ITS, and the importance of the ITS Project to the industry. (Author)

  11. Creation of the relevant next: How living systems capture the power of the adjacent possible through sign use.

    Science.gov (United States)

    Favareau, Donald F

    2015-12-01

    Stuart Kauffman's revolutionary notion of the Adjacent Possible as an organizing principle in nature shares much in common with logician Charles S. Peirce's understanding of the universe as an ever-unfolding 'process ontology' of possibility space that is brought about through the recursive interaction of genuine possibility, transiently actualized order, and emergent (but never fully deterministic) lawfulness. Proceeding from these three fundamental categories of becoming-as-being, Peirce developed a complimentary logic of sign relations that, along with Estonian biologist Jakob von Uexküll's action-as-meaning-imprinting Umwelt theory, informs the work that is currently being undertaken under the aegis of Biosemiotics. In this paper, I will highlight the deep affinities between Kauffman's notion of the Adjacent Possible and Biosemiotics' hybrid Peircean/Uexküllian "sign" concept, by which living systems - both as individuals and in the aggregate (i.e., as co-actors, communities and lineages) - "capture" relevant aspects of their relations with the immediately given Adjacent Possible and preserve those recipes for future interaction possibilities as biologically instantiated signs. By so doing, living systems move into the Adjacent Possible by "collapsing the wave function" of possibility not just probabilistically, but guided by system-internal values arising from previously captured sign relations that are biologically instantiated as replicable system biases and generative constraints. The influence of such valenced and end-directed action in the world introduces into the universe the phenomenon of the Relevant (and not just deterministic, or even stochastic) Next. My argument in this paper is that organisms live out their lives perpetually confronted with negotiating the omnipresent Relevant Next, and are informed by the biological capture of their (and their lineage's) previous engagements in doing so. And because that "capture" of previous agent

  12. Improved Refractories for Slagging Gasifiers in IGCC Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Dogan, Cynthia P.; Kwong, Kyei-Sing; Bennett, James P.; Chinn, Richard E.

    2003-04-24

    The gasification of coal and other carbon-containing fuels provides the opportunity to produce energy more efficiently, and with significantly less environmental impact, than more-conventional combustion-based processes. In addition, the synthesis gas that is the product of the gasification process offers the option of ''polygeneration,'' i.e., the production of alternative products instead of power should it be economically favorable to do so. Because of these advantages, gasification is viewed as one of the key processes in the U.S. Department of Energy's Vision 21 power system. However, issues with both the reliability and the economics of gasifier operation will have to be resolved before gasification will be widely adopted by the power industry. Central to both enhanced reliability and economics is the development of materials with longer service lives in gasifier systems that can provide extended periods of continuous, trouble-free gasifier operation. The focus of the Advanced Refractories for Gasification project at the Albany Research Center is to develop improved refractory materials capable of withstanding the harsh, high-temperature environment created by the gasification reaction, and includes both the refractory lining that protects and insulates the slagging gasifier, as well as the thermocouple assemblies that are utilized to monitor gasifier operating temperatures. Current generation refractory liners in slagging gasifiers are typically replaced every four to 18 months, at costs ranging up to $2,000,000, depending upon the size of the gasification vessel. Compounding materials and installation costs are the lost-opportunity costs for the time that the gasifier is off-line for the refractory exchange. Current generation thermocouple devices rarely survive the gasifier start-up process, leaving the operator with no real means of temperature measurement during routine operation. Reliable, efficient, and economical gasifier

  13. Reactive Power Dispatch Method in Wind Farms to Improve the Lifetime of Power Converter Considering Wake Effect

    DEFF Research Database (Denmark)

    Tian, Jie; Zhou, Dao; Su, Chi;

    2017-01-01

    Generator (DFIG) WT and the lifetime of DFIG WT’s power converter, a reactive power dispatch method is proposed in the WF with DFIG WTs to improve the lifetime of the upstream WT’s power converter. The proposed reactive power dispatch method is analyzed and demonstrated by the simulation on a WF with 80...... DFIG WTs. It can be concluded that, compared with the traditional reactive power dispatch method, the proposed method can increase the lifetime of the upstream WT’s power converter....

  14. An examination of heat rate improvements due to waste heat integration in an oxycombustion pulverized coal power plant

    Science.gov (United States)

    Charles, Joshua M.

    Oxyfuel, or oxycombustion, technology has been proposed as one carbon capture technology for coal-fired power plants. An oxycombustion plant would fire coal in an oxidizer consisting primarily of CO2, oxygen, and water vapor. Flue gas with high CO2 concentrations is produced and can be compressed for sequestration. Since this compression generates large amounts of heat, it was theorized that this heat could be utilized elsewhere in the plant. Process models of the oxycombustion boiler, steam cycle, and compressors were created in ASPEN Plus and Excel to test this hypothesis. Using these models, heat from compression stages was integrated to the flue gas recirculation heater, feedwater heaters, and to a fluidized bed coal dryer. All possible combinations of these heat sinks were examined, with improvements in coal flow rate, Qcoal, net power, and unit heat rate being noted. These improvements would help offset the large efficiency impacts inherent to oxycombustion technology.

  15. Capture and exploration of sample quality data to inform and improve the management of a screening collection.

    Science.gov (United States)

    Charles, Isabel; Sinclair, Ian; Addison, Daniel H

    2014-04-01

    A new approach to the storage, processing, and interrogation of the quality data for screening samples has improved analytical throughput and confidence and enhanced the opportunities for learning from the accumulating records. The approach has entailed the design, development, and implementation of a database-oriented system, capturing information from the liquid chromatography-mass spectrometry capabilities used for assessing the integrity of samples in AstraZeneca's screening collection. A Web application has been developed to enable the visualization and interactive annotation of the analytical data, monitor the current sample queue, and report the throughput rate. Sample purity and identity are certified automatically on the chromatographic peaks of interest if predetermined thresholds are reached on key parameters. Using information extracted in parallel from the compound registration and container inventory databases, the chromatographic and spectroscopic profiles for each vessel are linked to the sample structures and storage histories. A search engine facilitates the direct comparison of results for multiple vessels of the same or similar compounds, for single vessels analyzed at different time points, or for vessels related by their origin or process flow. Access to this network of information has provided a deeper understanding of the multiple factors contributing to sample quality assurance.

  16. Improved Power Quality Monitoring through Phasor Measurement Unit Data Interpretation

    DEFF Research Database (Denmark)

    Pertl, Michael; Marinelli, Mattia; Bindner, Henrik W.

    2015-01-01

    the correct actions for operating the system. In future power systems more measuring sensors including phasor measurement units will be available distributed all over the power system. They can and should be utilized to increase the observability of the power system. In this paper the impact of photovoltaic....... The voltage unbalance factor (VUF) could be a ‘new’ observable for a particular power system condition. Information about the actual injected wind power for a certain grid area could be derived without knowing/measuring the real wind power injection....

  17. A Preliminary Assessment of the Initial Compression Power Requirement in CO2 Pipeline “Carbon Capture and Storage (CCS Technologies”

    Directory of Open Access Journals (Sweden)

    Abdussalam El-Suleiman

    2016-05-01

    Full Text Available CO2 captured from fossil-fueled power generation plants is said to be economically transported via pipelines over long distances. The CO2 must be compressed to pipeline specifications using compressors and pumps that are driven by gas turbine (GT or other prime movers. This paper presents the evaluation of actual work transfer or required prime power by modeling the governing equations of compression using the Peng–Robinson equation of state (PR-EOS. A computer code was developed to carry out the modeling and subsequent simulation of the compression power requirement. The simulation of prime mover power was carried out for different technology (head per stage of the compressor ranging from 10-staged compression to double stage compression. The results show that the current technology of the centrifugal compressor could require as much as 23MW of prime mover power to compress 1.5 million tonnes per year of CO2—a projected equivalent CO2 released from a 530MW combined cycle gas turbine (CCGT power generation plant.

  18. Introducing Model Predictive Control for Improving Power Plant Portfolio Performance

    DEFF Research Database (Denmark)

    Edlund, Kristian Skjoldborg; Bendtsen, Jan Dimon; Børresen, Simon

    2008-01-01

    This paper introduces a model predictive control (MPC) approach for construction of a controller for balancing the power generation against consumption in a power system. The objective of the controller is to coordinate a portfolio consisting of multiple power plant units in the effort to perform...

  19. Regulation of Electric Power Generation while Improving TTP Use Efficiency

    Directory of Open Access Journals (Sweden)

    V. Romaniuk

    2012-01-01

    Full Text Available Taking integrated power system of theRepublicofBelarusas an example the paper considers a possibility of heat accumulator use for TPP operation in accordance with the schedule of electric power consumption while maintaining daily supply of heat energy from turbine power takes-off and without involvement of peak-loader boilers used for covering energy loads.

  20. Mercury Emissions Capture Efficiency with Activated Carbon Injection at a Russian Coal-Fired Thermal Power Plant

    Science.gov (United States)

    This EPA-led project, conducted in collaboration with UNEP, the Swedish Environmental Institute and various Russian Institutes, that demonstrates that the mercury emission control efficiencies of activated carbon injection technologies applied at a Russian power plant burning Rus...

  1. Mercury Emissions Capture Efficiency with Activated Carbon Injection at a Russian Coal-Fired Thermal Power Plant

    Science.gov (United States)

    This EPA-led project, conducted in collaboration with UNEP, the Swedish Environmental Institute and various Russian Institutes, that demonstrates that the mercury emission control efficiencies of activated carbon injection technologies applied at a Russian power plant burning Rus...

  2. Surface Treatment for Improving Sulfidation Resistance of Fossil Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Sikka, V.K.

    2001-03-09

    The purpose of the cooperative research and development agreement (CRADA) between ABB Combustion Engineering, Inc. and the Oak Ridge National Laboratory (ORNL) was to develop improved, longer life, and corrosion resistance surfaces for fossil power system components for use primarily in sulfidizing environments. Four surface protection techniques were to be explored. These included diffusion process, weld overlay, hot-isostatic processing, and various spraying methods. The work was to focus on Fe{sub 3} Al-based iron aluminide to increase the component life. The successful completion of the CRADA would have required the achievement of the following four goals: (1) fabrication development, (2) characterization and possibly modification of the alloy to optimize its manufacturability and environmental resistance, (3) testing and evaluation of the specimens, and (4) fabrication and testing of prototype parts. Because of lack of active participation from the participant, this CRADA did not achieve all of its goals and was terminated prematurely. Work carried out at ORNL on the CRADA is described in this report.

  3. CONCEPTS OF IMPROVING CURRENT PROTECTION OF POWER-GRID LINES

    Directory of Open Access Journals (Sweden)

    F. A. Romaniuk

    2015-01-01

    Full Text Available The  6–35  kV  power-grid  current  protection  serves  to  protect  the  transmission  lines against phase-to-phase short-circuits. The major disadvantage of it lies in the relatively large time delays of the last stages especially in the main sections of the grid owing to the stepped relay characteristics as well as a large number of the steps. A full-fledged protection of the 6–35 kV lines against inter-phase short circuits can be provided by the two-stage current protection: the first stage being the current cutoff without any time delay and the second stage – the maximum current protection where the time delay is linear contingent on the distance between the protection placement and the fault-point location. The article introduces the rating formulae for the time delays of the second-stage and their exemplary graphic presentation. The authors offer a variant for solving the problem with computation of the second-stage time delays in those instances where several feeders diverge from the bus bars of the substation located in the end of the protected line.Improving current protections for the 6–35 kV transmission lines with one-end power supply against interphase short-circuits can be based on the collective application of the following principles: accounting for the type and location of the short-circuit which provides for the high-performance cutoff zone instantaneous expansion and its independence on the mode of failure and the grid operation mode. It also allows increase of the last stage sensitiveness towards asymmetrical short-circuits; detection of the short-circuit location only on the results of fault currents measurement which simplifies the protection implementation; realization of the last (second protection stage with linear-dependent time delay which ensures potentiality of its operation speed increase.

  4. Multi-objective optimization of using NSGA-II in CO2 capture system for coal-fired power plant%燃煤电厂脱碳系统的模拟与多目标优化

    Institute of Scientific and Technical Information of China (English)

    马欢欢; 鄢烈祥; 李国建; 史彬

    2013-01-01

    In order to reduce the heat waste and increase heat efficiency, a method is proposed to improve the traditional CO2 capture system for coal-fired power plant by adding a multistage heat exchanger. Based on the 85%of CO2 capture rate, the utility consumption is depressed to the original 51.61%. Multi-objective optimization of heat consumption and carbon dioxide capture rate is proposed instead of single object optimization. At first, the modified carbon dioxide removal system for coal-fired power plant is modeled using Aspen Plus. Multi-objective optimization using Non-dominated sorting genetic algorithm with elitist strategy (NSGA-II) was performed based on the Aspen Plus simulation and MATLAB. At last, the Pareto-optimal set for the two optimization objective of carbon dioxide capture rate and reboiler heat duty is obtained and the best compromise solution is achieved using a fuzzy decision-making process. Carbon dioxide capture rate reaches 95.92%, reboiler heat duty reaches 775.39 MW, which provide a theoretical basis for process optimization.%针对燃煤电厂脱碳系统余热浪费问题,提出了增加多级换热器MHeatX模块的改进设计以提高热量利用率。在保证CO2捕获率为85%的前提下,可降低系统总公用工程消耗量48.39%。在此基础上,再应用带精英策略的非支配排序遗传算法(NSGA-II)对脱碳系统的热能消耗和CO2捕获率2个目标进行了同步优化,得到了碳捕获率和再沸器热负荷的最优Pareto解集。为了将优化结果应用于实际,本文采用模糊集方法求得最优妥协解,可使CO2捕获率达到95.92%,再沸器负荷降至775.39 MW,为该工艺的优化操作提供了理论依据。

  5. Power Generation Technology Using CO2 Capture Energy Storage%利用捕捉的 CO2贮能发电技术研究

    Institute of Scientific and Technical Information of China (English)

    金家敏

    2016-01-01

    碳捕捉技术是指通过一定的方法,将工业生产中产生的CO2分离出来进行储存和利用的工艺和技术。论述了利用捕捉的二氧化碳贮能发电和生产煤气的技术,包括生产流程、电热煤气发生炉、技术可行性、经济效益等,并对碳气化贮能经济效益进行估算,得到碳气化贮能不仅不要外电补足,而且还有多余的电能供应它用,有很大的优越性。%Carbon‐capture technology is to separate CO2 generated during the industrial production for storage and utilization .This paper discusses the technology of applying the captured CO2 for power generation and coal gas production ,including production process ,electric gas furnace ,technical feasibility and economic benefit etc .,and estimates the economic benefit of carbon gasification energy storage .And it is concluded that carbon gasification energy storage can not only need no redundant power supply ,but also exhibits great advantages .

  6. Engineering and Economic Analysis of an Advanced Ultra-Supercritical Pulverized Coal Power Plant with and without Post-Combustion Carbon Capture Task 7. Design and Economic Studies

    Energy Technology Data Exchange (ETDEWEB)

    Booras, George [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States); Powers, J. [General Electric, Schenectady, NY (United States); Riley, C. [General Electric, Schenectady, NY (United States); Hendrix, H. [Hendrix Engineering Solutions, Inc., Calera, AL (United States)

    2015-09-01

    This report evaluates the economics and performance of two A-USC PC power plants; Case 1 is a conventionally configured A-USC PC power plant with superior emission controls, but without CO2 removal; and Case 2 adds a post-combustion carbon capture (PCC) system to the plant from Case 1, using the design and heat integration strategies from EPRI’s 2015 report, “Best Integrated Coal Plant.” The capture design basis for this case is “partial,” to meet EPA’s proposed New Source Performance Standard, which was initially proposed as 500 kg-CO2/MWh (gross) or 1100 lb-CO2/MWh (gross), but modified in August 2015 to 635 kg-CO2/MWh (gross) or 1400 lb-CO2/MWh (gross). This report draws upon the collective experience of consortium members, with EPRI and General Electric leading the study. General Electric provided the steam cycle analysis as well as v the steam turbine design and cost estimating. EPRI performed integrated plant performance analysis using EPRI’s PC Cost model.

  7. Feasibility of a novel mHealth management system to capture and improve medication adherence among adolescents with asthma

    Directory of Open Access Journals (Sweden)

    Cushing A

    2016-11-01

    Full Text Available Anna Cushing,1,2 Melissa P Manice,1,2 Andrew Ting,3 Michael K Parides1 1Department of Population Health Science and Policy, Icahn School of Medicine at Mount Sinai, Icahn Medical Institute, 2CoheroHealth, LLC, 3Division of Pulmonary and Critical Care, Department of Pediatrics, Icahn School of Medicine at Mount Sinai, New York, NY, USA Purpose: Currently, 7.1 million children in the United States have asthma. Nonadherence to daily controller asthma medication is common, leading to more severe symptoms, overuse of rescue medication, and increased hospitalizations. The purpose of this study was to develop and evaluate the feasibility and acceptability of a novel mHealth management system composed of a sensored device, which is connected to mobile phone app that is designed to monitor and improve asthma medication adherence. Patients and methods: The asthma management system was designed using well-established behavioral theory. Seven adolescents aged 11–18 years were enrolled and given an adherence sensor, and four of those also received a mobile phone app with game features and reminders. Five patients completed the study, and one was lost to follow-up in each group. Mobile app users and their parents participated in focus groups to assess patient preferences. Feasibility was assessed by the ability of sensors to capture real-time medication data. Acceptability was assessed by patient questionnaire and focus group analysis. Results: Successful upload of real-time data from six of seven inhaler sensors to the HIPAA-compliant server demonstrates the feasibility of at-home patient monitoring using the sensor device. All three mobile app users who completed the study reported interest in continued use of the management system and would recommend the app to friends. Unstructured interviews and focus groups revealed that patients felt that the intervention helped their sense of asthma control. Conclusion: This study demonstrates the feasibility of

  8. Examination of the effect of system pressure ratio and heat recuperation on the efficiency of a coal based gas turbine fuel cell hybrid power generation system with CO2 capture

    Energy Technology Data Exchange (ETDEWEB)

    VanOsdol, J.G.; Gemmen, R.S.; Liese, E.A

    2008-06-01

    This paper examines two coal-based hybrid configurations that employ separated anode and cathode streams for the capture and compression of CO2. One configuration uses a standard Brayton cycle, and the other adds heat recuperation ahead of the fuel cell. Results show that peak efficiencies near 55% are possible, regardless of cycle configuration, including the cost in terms of energy production of CO2 capture and compression. The power that is required to capture and compress the CO2 is shown to be approximately 15% of the total plant power.

  9. Screen-Capturing System with Two-Layer Display for PowerPoint Presentation to Enhance Classroom Education

    Science.gov (United States)

    Lai, Yen-Shou; Tsai, Hung-Hsu; Yu, Pao-Ta

    2011-01-01

    This paper proposes a new presentation system integrating a Microsoft PowerPoint presentation in a two-layer method, called the TL system, to promote learning in a physical classroom. With the TL system, teachers can readily control hints or annotations as a way of making them visible or invisible to students so as to reduce information load. In…

  10. Improvement of the Performance of Scheduled Stepwise Power Programme Changes within the European Power System

    DEFF Research Database (Denmark)

    Welfonder, E.; Weissbach, T.; Schulz, U.

    2008-01-01

    units. These power imbalances may occur within single control areas or between different control areas. Therefore, as a countermeasure, power output ramps with a standardised ramp duration of 2T ≤ 15 min are required so that no power imbalance occurs during scheduled power programme changes. After......Since the deregulation of the electrical energy market, the technical realisation of power transactions based on energy market contracts often effects large stepwise power programme changes – especially at the change of the hour. Due to mainly economic reasons these stepwise power programme changes...... lead to remarkable power imbalances within the European Power System causing large unintended frequency deviations. In case of these – mostly negative – frequency deviations up to Δf = -150 mHz, considerably more than half of the primary control reserve is activated needlessly, which highly stresses...

  11. Improving Prediction Accuracy of a Rate-Based Model of an MEA-Based Carbon Capture Process for Large-Scale Commercial Deployment

    Directory of Open Access Journals (Sweden)

    Xiaobo Luo

    2017-04-01

    Full Text Available Carbon capture and storage (CCS technology will play a critical role in reducing anthropogenic carbon dioxide (CO2 emission from fossil-fired power plants and other energy-intensive processes. However, the increment of energy cost caused by equipping a carbon capture process is the main barrier to its commercial deployment. To reduce the capital and operating costs of carbon capture, great efforts have been made to achieve optimal design and operation through process modeling, simulation, and optimization. Accurate models form an essential foundation for this purpose. This paper presents a study on developing a more accurate rate-based model in Aspen Plus® for the monoethanolamine (MEA-based carbon capture process by multistage model validations. The modeling framework for this process was established first. The steady-state process model was then developed and validated at three stages, which included a thermodynamic model, physical properties calculations, and a process model at the pilot plant scale, covering a wide range of pressures, temperatures, and CO2 loadings. The calculation correlations of liquid density and interfacial area were updated by coding Fortran subroutines in Aspen Plus®. The validation results show that the correlation combination for the thermodynamic model used in this study has higher accuracy than those of three other key publications and the model prediction of the process model has a good agreement with the pilot plant experimental data. A case study was carried out for carbon capture from a 250 MWe combined cycle gas turbine (CCGT power plant. Shorter packing height and lower specific duty were achieved using this accurate model.

  12. Improved cutting performance in high power laser cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    2003-01-01

    Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

  13. Improved cutting performance in high power laser cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    2003-01-01

    Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

  14. Improvement of Power Efficiency using Smart Antenna System in MANETs

    Directory of Open Access Journals (Sweden)

    Abhishek Kumar

    2014-11-01

    Full Text Available Performance of ad-hoc networks is low under omnidirectional antenna systems compared to smart antenna system. Directional antennas cover large area {&} save some amount of transmitted power because it focuses in desired direction accordance with mobility of nodes while Omni-directional antennas cover small area {&} needs large transmitted power as compared to Smart Antenna System (SAS. In this paper, we will overcome the problem of unnecessary transmitted power wastage with omnidirectional antenna system in ad-hoc wireless networks by using Smart Antenna Systems (SAS. We will calculate {&} analyze transmitted power variations with different number of mobile nodes in mobile ad-hoc networks [MANETs] with smart antenna system (SAS {&} Omni-directional antenna system in different conditions. Firstly, we will calculate {&} analyze transmitted power during flooding of packets means in case of route creation, and secondly, when communication will established between transmitter {&} receiver

  15. Assessment of the US EPA's determination of the role for CO2 capture and storage in new fossil fuel-fired power plants.

    Science.gov (United States)

    Clark, Victoria R; Herzog, Howard J

    2014-07-15

    On September 20, 2013, the US Environmental and Protection Agency (EPA) proposed a revised rule for "Standards of Performance for Greenhouse Gas Emissions from New Stationary Sources: Electric Utility Generating Units". These performance standards set limits on the amount of carbon dioxide (CO2) that can be emitted per megawatt-hour (MWh) of electricity generation from new coal-fired and natural gas-fired power plants built in the US. These limits were based on determinations of "best system of emission reduction (BSER) adequately demonstrated". Central in this determination was evaluating whether Carbon Dioxide Capture and Storage (CCS) qualified as BSER. The proposed rule states that CCS qualifies as BSER for coal-fired generation but not for natural gas-fired generation. In this paper, we assess the EPA's analysis that resulted in this determination. We are not trying to judge what the absolute criteria are for CCS as the BSER but only the relative differences as related to coal- vs natural gas-fired technologies. We conclude that there are not enough differences between "base load" coal-fired and natural gas-fired power plants to justify the EPA's determination that CCS is the BSER for coal-fired power plants but not for natural gas-fired power plants.

  16. Reactive power control methods for improved reliability of wind power inverters under wind speed variations

    DEFF Research Database (Denmark)

    Ma, Ke; Liserre, Marco; Blaabjerg, Frede

    2012-01-01

    The thermal cycling of power switching devices may lead to failures that compromise the reliability of power converters. Wind Turbine Systems (WTS) are especially subject to severe thermal cycling which may be caused by the wind speed variations or power grid faults. This paper proposes a control...... in the most stressed devices. The possible model-based control system for the proposed method is demonstrated, designed and simulated based on the Three-level Neutral-Point- Clamped (3L-NPC) grid-connected converters. It is concluded that with the proposed reactive power control method, the junction...... method to relieve the thermal cycling of power switching devices under severe wind speed variations, by circulating reactive power among the parallel power converters in a WTS or among the WTS's in a wind park. The amount of reactive power is adjusted to limit the junction temperature fluctuation...

  17. Alstom's Chemical Looping Combustion Prototype for CO2 Capture from Existing Pulverized Coal-Fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Andrus, Jr., Herbert E. [Alstom Power Inc., Windsor, CT (United States); Chiu, John H. [Alstom Power Inc., Windsor, CT (United States); Edberg, Carl D. [Alstom Power Inc., Windsor, CT (United States); Thibeault, Paul R. [Alstom Power Inc., Windsor, CT (United States); Turek, David G. [Alstom Power Inc., Windsor, CT (United States)

    2012-09-30

    Alstom’s Limestone Chemical Looping (LCL™) process has the potential to capture CO2 from new and existing coal-fired power plants while maintaining high plant power generation efficiency. This new power plant concept is based on a hybrid combustion- gasification process utilizing high temperature chemical and thermal looping technology. This process could also be potentially configured as a hybrid combustion-gasification process producing a syngas or hydrogen for various applications while also producing a separate stream of CO2 for use or sequestration. The targets set for this technology is to capture over 90% of the total carbon in the coal at cost of electricity which is less than 20% greater than Conventional PC or CFB units. Previous work with bench scale test and a 65 kWt Process Development Unit Development (PDU) has validated the chemistry required for the chemical looping process and provided for the investigation of the solids transport mechanisms and design requirements. The objective of this project is to continue development of the combustion option of chemical looping (LCL-C™) by designing, building and testing a 3 MWt prototype facility. The prototype includes all of the equipment that is required to operate the chemical looping plant in a fully integrated manner with all major systems in service. Data from the design, construction, and testing will be used to characterize environmental performance, identify and address technical risks, reassess commercial plant economics, and develop design information for a demonstration plant planned to follow the proposed Prototype. A cold flow model of the prototype will be used to predict operating conditions for the prototype and help in operator training. Operation of the prototype will provide operator experience with this new technology and performance data of the LCL-C™ process, which will be applied to the commercial design and economics and plan for a future demonstration

  18. Alstom's Chemical Looping Combustion Prototype for CO{sub 2} Capture from Existing Pulverized Coal-Fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Andrus, Herbert; Chiu, John; Edberg, Carl; Thibeault, Paul; Turek, David

    2012-09-30

    Alstom’s Limestone Chemical Looping (LCL™) process has the potential to capture CO{sub 2} from new and existing coal-fired power plants while maintaining high plant power generation efficiency. This new power plant concept is based on a hybrid combustion- gasification process utilizing high temperature chemical and thermal looping technology. This process could also be potentially configured as a hybrid combustion-gasification process producing a syngas or hydrogen for various applications while also producing a separate stream of CO{sub 2} for use or sequestration. The targets set for this technology is to capture over 90% of the total carbon in the coal at cost of electricity which is less than 20% greater than Conventional PC or CFB units. Previous work with bench scale test and a 65 kWt Process Development Unit Development (PDU) has validated the chemistry required for the chemical looping process and provided for the investigation of the solids transport mechanisms and design requirements. The objective of this project is to continue development of the combustion option of chemical looping (LCL-C™) by designing, building and testing a 3 MWt prototype facility. The prototype includes all of the equipment that is required to operate the chemical looping plant in a fully integrated manner with all major systems in service. Data from the design, construction, and testing will be used to characterize environmental performance, identify and address technical risks, reassess commercial plant economics, and develop design information for a demonstration plant planned to follow the proposed Prototype. A cold flow model of the prototype will be used to predict operating conditions for the prototype and help in operator training. Operation of the prototype will provide operator experience with this new technology and performance data of the LCL-C™ process, which will be applied to the commercial design and economics and plan for a future demonstration plant.

  19. Capture ready study

    Energy Technology Data Exchange (ETDEWEB)

    Minchener, A.

    2007-07-15

    There are a large number of ways in which the capture of carbon as carbon dioxide (CO{sub 2}) can be integrated into fossil fuel power stations, most being applicable for both gas and coal feedstocks. To add to the choice of technology is the question of whether an existing plant should be retrofitted for capture, or whether it is more attractive to build totally new. This miscellany of choices adds considerably to the commercial risk of investing in a large power station. An intermediate stage between the non-capture and full capture state would be advantageous in helping to determine the best way forward and hence reduce those risks. In recent years the term 'carbon capture ready' or 'capture ready' has been coined to describe such an intermediate stage plant and is now widely used. However a detailed and all-encompassing definition of this term has never been published. All fossil fuel consuming plant produce a carbon dioxide gas byproduct. There is a possibility of scrubbing it with an appropriate CO{sub 2} solvent. Hence it could be said that all fossil fuel plant is in a condition for removal of its CO{sub 2} effluent and therefore already in a 'capture ready' state. Evidently, the practical reality of solvent scrubbing could cost more than the rewards offered by such as the ETS (European Trading Scheme). In which case, it can be said that although the possibility exists of capturing CO{sub 2}, it is not a commercially viable option and therefore the plant could not be described as ready for CO{sub 2} capture. The boundary between a capture ready and a non-capture ready condition using this definition cannot be determined in an objective and therefore universally acceptable way and criteria must be found which are less onerous and less potentially contentious to assess. 16 refs., 2 annexes.

  20. Improvement of Power System Stability using Artificial Neural Network based HVDC Controls

    Directory of Open Access Journals (Sweden)

    Nagu Bhookya

    2013-06-01

    Full Text Available In this paper, investigation is carried out for the improvement of power system stability by utilizing auxiliary controls for controlling HVDC power flow. The current controller model and the line dynamics are considered in the stability analysis. Transient stability analysis is done on a multi-machine system, where, a neural network controller is developed to improve the stability of the power system and to improve the response time of the controller to the changing conditions in power system. The results show the application of the neural network controller in AC-DC power systems.

  1. Improvement of the Performance of Scheduled Stepwise Power Programme Changes within the European Power System

    DEFF Research Database (Denmark)

    Welfonder, E.; Weissbach, T.; Schulz, U.

    2008-01-01

    Since the deregulation of the electrical energy market, the technical realisation of power transactions based on energy market contracts often effects large stepwise power programme changes – especially at the change of the hour. Due to mainly economic reasons these stepwise power programme changes...... lead to remarkable power imbalances within the European Power System causing large unintended frequency deviations. In case of these – mostly negative – frequency deviations up to Δf = -150 mHz, considerably more than half of the primary control reserve is activated needlessly, which highly stresses...

  2. Power electronics improving 3-Wire DC railways electrification

    OpenAIRE

    Rull Duran, Joan; Bergas Jané, Joan Gabriel; Galceran Arellano, Samuel; Sumper, Andreas; Coves Moreno, Jordi

    2009-01-01

    Urban DC railway substations are growing in size due increasing capacity demand. Several challenges associated with the increase of power demand can be met using power electronics. The proposed system is based on DC-autotransformers and active rectifiers working similarly to those in 3-wire AC railway electrification system. Conventional simulation software (Idom-REPS-DC) has been adapted to the system. A real subway line and the same line with the proposed 3-Wire DC working in the same condi...

  3. Power Quality Improvement And Mitigation Of Voltage Sag And Current Swell Using Distributed Power Flow Controller

    Directory of Open Access Journals (Sweden)

    P.NIRMALA

    2014-09-01

    Full Text Available Modern power utilities have to respond to a number of challenges such as growth of electricity demand specially in non-linear loads in power grids, consequently, That higher power quality should be considered. In this paper, DPFC which is similar to unified power flow controller (UPFC in structure, which is used to mitigate the voltage sag and swell as a power quality issue. Unlike UPFC, the common dc-link in DPFC, between the shunt and series converter devices should be eliminated and three-phase series converter is divided to several single-phase series distributed converters through the power transmission line. And also to detect the voltage sags and find out the three single-phase reference voltages of DPFC, the synchronous reference frame method is proposed. Application of DPFC in power quality enhancement is simulated in Mat lab/Simulink environment which show the effectiveness of the proposed structure

  4. Improving Switching Performance of Power MOSFETs Used in High Rep-Rate, Short Pulse, High-Power Pulsers

    Energy Technology Data Exchange (ETDEWEB)

    Cook, E G

    2006-09-19

    As their switching and power handling characteristics improve, solid-state devices are finding new applications in pulsed power. This is particularly true of applications that require fast trains of short duration pulses. High voltage (600-1200V) MOSFETs are especially well suited for use in these systems, as they can switch at significant peak power levels and are easily gated on and off very quickly. MOSFET operation at the shortest pulse durations is not constrained by the intrinsic capabilities of the MOSFET, but rather by the capabilities of the gate drive circuit and the system physical layout. This project sought to improve MOSFET operation in a pulsed power context by addressing these issues. The primary goal of this project is to improve the switching performance of power MOSFETs for use in high rep-rate, short pulse, high-power applications by improving the design of the gate drive circuits and the circuit layouts used in these systems. This requires evaluation of new commercial gate drive circuits and upgrading the designs of LLNL-developed circuits. In addition, these circuits must be tested with the fastest available high-voltage power MOSFETs.

  5. Improved Structural Design and CO2 Capture of Porous Hydroxy-Rich Polymeric Organic Frameworks

    Energy Technology Data Exchange (ETDEWEB)

    Kidder, Michelle K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Earl, Lyndsey D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); de Almeida, Valmor F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-04-16

    Polymeric organic frameworks (POFs) are tunable and robust porous materials with potential applications for gas capture, catalysis, and separations technologies. A series of new porous POFs have been synthesized from the reaction of phloroglucinol or resorcinol derivatives with aryl aldehyde precursors. The monomers have various molecular shapes including linear, bent, trigonal, and tetrahedral geometries. Depending on the size and geometric matching of the monomers, the polymers are dominantly microporous with some mesoporous character or they are non-porous. In addition to standard spectroscopic and surface characterization, the materials were screened as adsorbents for carbon dioxide capture at low pressure (0-1 bar). The best performing material (POF 1D) has a CO2 capture capacity of 9.0 wt. % (2.04 mmol g-1) at 298 K and 1 bar which is comparable to other polymeric organic frameworks. Isosteric heats of adsorption for POF 1A, POF 2A, and POF 2B were found to be dependent on the weight percent of CO2 adsorbed: this suggests there are both chemisorptive and physisorptive components of CO2 capture by the POFs.

  6. New rht-Type Metal-Organic Frameworks Decorated with Acylamide Groups for Efficient Carbon Dioxide Capture and Chemical Fixation from Raw Power Plant Flue Gas.

    Science.gov (United States)

    Guo, Xiangyang; Zhou, Zhen; Chen, Cong; Bai, Junfeng; He, Cheng; Duan, Chunying

    2016-11-23

    The combination of carbon dioxide capture and chemical fixation in a one-pot process is attractive for both chemists and governments. The cycloaddition of carbon dioxide with epoxides to produce cyclic carbonates is an atomic economical reaction without any side products. By incorporating acylamide to enhance the binding affinity toward CO2, new rht-type metal-organic frameworks (MOFs) with (3, 28) and (3, 24) connected units were constructed. Zn-NTTA with two types of dinuclear paddlewheel building blocks-{Zn2(OOC(-))4} and {Zn2(OOC(-))3}. The high uptake of CO2 (115.6 cm(3)·g(-1)) and selectivity over N2 (30:1) at 273 K indicated that these MOFs are excellent candidates for postcombustion CO2 isolation and capture. The MOFs feature high catalytic activity, rapid dynamics of transformation and excellent stability with turnover number (TON) values up to 110 000 per paddlewheel unit after 5 × 6 rounds of recyclability, demonstrating that they are promising heterogeneous catalysts for CO2 cyclo-addition to value-added cyclic carbonates. The cycloaddition of epoxides with wet gases demonstrated that the catalyst activity was not affected by moisture, and the indices of the PXRD patterns of the bulk samples filtered from the catalytic reaction revealed that the crystallinities were maintained. The combination of the selective capture and catalytic transformation in one-pot enables the use of a negative-cost feedstock-raw power plant flue gas without any separation and purification-revealing the broad prospects of such MOFs for practical CO2 fixation in industry.

  7. Towards more accurate wind and solar power prediction by improving NWP model physics

    Science.gov (United States)

    Steiner, Andrea; Köhler, Carmen; von Schumann, Jonas; Ritter, Bodo

    2014-05-01

    The growing importance and successive expansion of renewable energies raise new challenges for decision makers, economists, transmission system operators, scientists and many more. In this interdisciplinary field, the role of Numerical Weather Prediction (NWP) is to reduce the errors and provide an a priori estimate of remaining uncertainties associated with the large share of weather-dependent power sources. For this purpose it is essential to optimize NWP model forecasts with respect to those prognostic variables which are relevant for wind and solar power plants. An improved weather forecast serves as the basis for a sophisticated power forecasts. Consequently, a well-timed energy trading on the stock market, and electrical grid stability can be maintained. The German Weather Service (DWD) currently is involved with two projects concerning research in the field of renewable energy, namely ORKA*) and EWeLiNE**). Whereas the latter is in collaboration with the Fraunhofer Institute (IWES), the project ORKA is led by energy & meteo systems (emsys). Both cooperate with German transmission system operators. The goal of the projects is to improve wind and photovoltaic (PV) power forecasts by combining optimized NWP and enhanced power forecast models. In this context, the German Weather Service aims to improve its model system, including the ensemble forecasting system, by working on data assimilation, model physics and statistical post processing. This presentation is focused on the identification of critical weather situations and the associated errors in the German regional NWP model COSMO-DE. First steps leading to improved physical parameterization schemes within the NWP-model are presented. Wind mast measurements reaching up to 200 m height above ground are used for the estimation of the (NWP) wind forecast error at heights relevant for wind energy plants. One particular problem is the daily cycle in wind speed. The transition from stable stratification during

  8. Ramp Forecasting Performance from Improved Short-Term Wind Power Forecasting: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, J.; Florita, A.; Hodge, B. M.; Freedman, J.

    2014-05-01

    The variable and uncertain nature of wind generation presents a new concern to power system operators. One of the biggest concerns associated with integrating a large amount of wind power into the grid is the ability to handle large ramps in wind power output. Large ramps can significantly influence system economics and reliability, on which power system operators place primary emphasis. The Wind Forecasting Improvement Project (WFIP) was performed to improve wind power forecasts and determine the value of these improvements to grid operators. This paper evaluates the performance of improved short-term wind power ramp forecasting. The study is performed for the Electric Reliability Council of Texas (ERCOT) by comparing the experimental WFIP forecast to the current short-term wind power forecast (STWPF). Four types of significant wind power ramps are employed in the study; these are based on the power change magnitude, direction, and duration. The swinging door algorithm is adopted to extract ramp events from actual and forecasted wind power time series. The results show that the experimental short-term wind power forecasts improve the accuracy of the wind power ramp forecasting, especially during the summer.

  9. The use of air-bottoming cycle as a heat source for the carbon dioxide capture installation of a coal-fired power unit

    Science.gov (United States)

    Chmielniak, Tadeusz; Lepszy, Sebastian; Czaja, Daniel

    2011-12-01

    The installations of CO2 capture from flue gases using chemical absorption require a supply of large amounts of heat into the system. The most common heating medium is steam extracted from the cycle, which results in a decrease in the power unit efficiency. The use of heat needed for the desorption process from another source could be an option for this configuration. The paper presents an application of gas-air systems for the generation of extra amounts of energy and heat. Gas-air systems, referred to as the air bottoming cycle (ABC), are composed of a gas turbine powered by natural gas, air compressor and air turbine coupled to the system by means of a heat exchanger. Example configurations of gas-air systems are presented. The efficiency and power values, as well as heat fluxes of the systems under consideration are determined. For comparison purposes, the results of modelling a system consisting of a gas turbine and a regenerative exchanger are presented.

  10. Non Linear Analysis of MPPT for Power Quality Improvement

    Directory of Open Access Journals (Sweden)

    S. Sankar

    2015-08-01

    Full Text Available In this study the conventional inverter interfacing renewable energy sources with the grid, without any additional hardware cost. Here, the main idea is the maximum utilization of inverter rating which is most of the time underutilized due to intermittent nature of RES. Based on the non-linear characteristics of PV, these thesis designs a VSS controller to realize the maximum power output of PV arrays. The output power from renewable energy sources fluctuates because of weather variations. This study proposes an effective power quality control strategy of renewable energy sources connected to power system using Photovoltaic (PV array. If the main controller used is a PR controller, any dc offset in a control loop will propagate through the system and the inverter terminal voltage will have a nonzero average value. In this strategy both load and inverter current sensing is required to compensate the load current harmonics. The non-linear load current harmonics may result in voltage harmonics and can create a serious PQ problem in the power system network.

  11. High power accelerator-based boron neutron capture with a liquid lithium target and new applications to treatment of infectious diseases

    Energy Technology Data Exchange (ETDEWEB)

    Halfon, S. [Soreq NRC, Yavne 81800 (Israel); Racah Institute of Physics, Hebrew University, Jerusalem 91904 (Israel)], E-mail: halfon@phys.huji.ac.il; Paul, M. [Racah Institute of Physics, Hebrew University, Jerusalem 91904 (Israel); Steinberg, D. [Biofilm Laboratory, Institute of Dental Sciences, Faculty of Dentistry, Hebrew University-Hadassah (Israel); Nagler, A.; Arenshtam, A.; Kijel, D. [Soreq NRC, Yavne 81800 (Israel); Polacheck, I. [Clinical Microbiology and Infectious Diseases, Hadassah-Hebrew University Medical Center (Israel); Srebnik, M. [Department of Medicinal Chemistry and Natural Products, School of Pharmacy, Hebrew University, Jerusalem 91120 (Israel)

    2009-07-15

    A new conceptual design for an accelerator-based boron neutron capture therapy (ABNCT) facility based on the high-current low-energy proton beam driven by the linear accelerator at SARAF (Soreq Applied Research Accelerator Facility) incident on a windowless forced-flow liquid-lithium target, is described. The liquid-lithium target, currently in construction at Soreq NRC, will produce a neutron field suitable for the BNCT treatment of deep-seated tumor tissues, through the reaction {sup 7}Li(p,n){sup 7}Be. The liquid-lithium target is designed to overcome the major problem of solid lithium targets, namely to sustain and dissipate the power deposited by the high-intensity proton beam. Together with diseases conventionally targeted by BNCT, we propose to study the application of our setup to a novel approach in treatment of diseases associated with bacterial infections and biofilms, e.g. inflammations on implants and prosthetic devices, cystic fibrosis, infectious kidney stones. Feasibility experiments evaluating the boron neutron capture effectiveness on bacteria annihilation are taking place at the Soreq nuclear reactor.

  12. High power accelerator-based boron neutron capture with a liquid lithium target and new applications to treatment of infectious diseases.

    Science.gov (United States)

    Halfon, S; Paul, M; Steinberg, D; Nagler, A; Arenshtam, A; Kijel, D; Polacheck, I; Srebnik, M

    2009-07-01

    A new conceptual design for an accelerator-based boron neutron capture therapy (ABNCT) facility based on the high-current low-energy proton beam driven by the linear accelerator at SARAF (Soreq Applied Research Accelerator Facility) incident on a windowless forced-flow liquid-lithium target, is described. The liquid-lithium target, currently in construction at Soreq NRC, will produce a neutron field suitable for the BNCT treatment of deep-seated tumor tissues, through the reaction (7)Li(p,n)(7)Be. The liquid-lithium target is designed to overcome the major problem of solid lithium targets, namely to sustain and dissipate the power deposited by the high-intensity proton beam. Together with diseases conventionally targeted by BNCT, we propose to study the application of our setup to a novel approach in treatment of diseases associated with bacterial infections and biofilms, e.g. inflammations on implants and prosthetic devices, cystic fibrosis, infectious kidney stones. Feasibility experiments evaluating the boron neutron capture effectiveness on bacteria annihilation are taking place at the Soreq nuclear reactor.

  13. Results from trialling aqueous NH{sub 3} based post combustion capture in a pilot plant at Munmorah power station. Desorption

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Hai; Morgan, Scott; Allport, Andrew; Cottrell, Aaron; Do, Thong; McGregor, James; Wardhaugh, Leigh; Feron, Paul [CSIRO Energy Centre, Mayfield West, NSW (Australia)

    2013-07-01

    Australia's Commonwealth Scientific and Industrial Research Organization (CSIRO) and Delta Electricity have tested an aqueous ammonia based post combustion capture (PCC) process in a pilot plant at Munmorah black coal fired power station. This paper presents and discusses the experimental results obtained and primarily focuses on the desorption section. A high purity of CO{sub 2} product was obtained at the stripper gas outlet with the CO{sub 2} volumetric concentration generally between 99-100% and the remainder being water and NH{sub 3}. An increase in stripper pressure/temperature can lead to a decrease in NH{sub 3} concentration in the CO{sub 2} product. The NH{sub 3} concentration can be controlled within 200 ppm without wash at a stripper pressure of 850 kPa (the maximum pressure tested) at a stripper gas outlet temperatures of 20-25 C. The solid precipitation occurred in the stripper condenser and reflux lines. Due to the low ammonia content in the solution, CO{sub 2} content in the solution was low and generally more than 50% of regeneration energy was used to heat up the solvent under the pilot plant conditions. The lowest regeneration energy obtained from the pilot plant trials is 4-4.2 MJ/kg CO{sub 2} captured. The effect of various parameters including solvent flow-rate and stripper temperature/pressure in the solvent on the regeneration energy was investigated.

  14. Power-Split Hybrid Electric Vehicle Energy Management Based on Improved Logic Threshold Approach

    Directory of Open Access Journals (Sweden)

    Zhumu Fu

    2013-01-01

    Full Text Available We design an improved logic threshold approach of energy management for a power-split HEV assisted by an integrated starter generator (ISG. By combining the efficiency map and the optimum torque curve of internal combustion engine (ICE with the state of charge (SOC of batteries, the improved logic threshold controller manages the ICE within its peak efficiency region at first. Then the electrical power demand is established based on the ICE energy output. On that premise, a variable logic threshold value K is defined to achieve the power distribution between the ISG and the electric motor/generator (EMG. Finally, simulation models for the power-split HEV with improved logic threshold controller are established in ADVISOR. Compared to the equally power-split HEV with the logic threshold controller, when using the improved logic threshold controller, the battery power consumption, the ICE efficiency, the fuel consumption, and the motor driving system efficiency are improved.

  15. Use of thermoelectric generators for improve power dependability over grid power

    Energy Technology Data Exchange (ETDEWEB)

    Archer, Jack [Global Thermoelectric, Calgary (Canada)

    2005-07-01

    A natural gas transportation company was experiencing extensive pipeline corrosion on some sections of their pipeline protected by impressed current using grid power and rectifiers. After determining that grid power was being interrupted on the affected sections, the gas transporter began looking for a more dependable power supply and chose thermoelectric generators. Since installing thermoelectric generators in 2002, the pipeline potentials have stabilized and transporter was able to experience 100% operational time on affected sections. (author)

  16. Development and fabrication of improved power transistor switches

    Science.gov (United States)

    Hower, P. L.; Chu, C. K.

    1979-01-01

    A new class of high-voltage power transistors was achieved by adapting present interdigitated thyristor processing techniques to the fabrication of npn Si transistors. Present devices are 2.3 cm in diameter and have V sub CEO (sus) in the range of 400 to 600V. V sub CEO (sus) = 450V devices were made with an (h sub FE)(I sub C) product of 900A at V sub CE = 2.5V. The electrical performance obtained was consistent with the predictions of an optimum design theory specifically developed for power switching transistors. The device design, wafer processing, and assembly techniques are described. Experimental measurements of the dc characteristics, forward SOA, and switching times are included. A new method of characterizing the switching performance of power transistors is proposed.

  17. Improved power converter for pulsed operation of DBD

    Science.gov (United States)

    Schwarz-Kiene, Peter; Heering, Wolfgang

    2000-04-01

    In this paper an electronic ballast for pulsed operation of dielectric barrier discharges (DBD) is presented. The converter is designed as a transformer coupled square wave power source optimized for capacitive loads like DBD. The special features are the bipolar trapezoid waveform with variable slew rate (dU/dt), duty cycle, frequency and amplitude of the output voltage, which is balanced to ground. The power stage is designed in zero voltage switching technology. The ballast is primarily designed to investigate the discharge characteristics of DBD in dependence on the waveform parameters. A simple electrical DBD model is presented, which allows to predict the external DBD voltage and the discharge power in dependence of slew rate and duty cycle. The paper is closed with some experimental results of pulse XeCl*-excimer lamps.

  18. Power Quality Improvement Wind Energy System Using Cascaded Multilevel Inverter

    Directory of Open Access Journals (Sweden)

    J.S. Sathiyanarayanan

    2013-02-01

    Full Text Available In this paper, a wind energy conversion system based on a cascaded H-bridgemultilevel inverter (CHBMLI topology has been proposed to be used for the grid interface of largesplit winding alternators (SWAs. A new method has been suggested for the generation of referencecurrents for the voltage source inverter (VSI depending upon the available wind power. TheCHBMLI has been used as a VSI and operated in a current control mode order to achieve theobjectives of real power injection and load compensation (power factor correction, load balancing,and harmonic compensation based on the proposed reference generation scheme. In the fieldexcitation control of SWA provides a single means vary the dc link voltages of all the CHBssimultaneously and proportionately.

  19. Technologies for coal based hydrogen and electricity co-production power plants with CO{sub 2} capture

    Energy Technology Data Exchange (ETDEWEB)

    Cortes, C.G.; Tzimas, E.; Peteves, S.D.

    2009-07-01

    Integrated Gasification Combined Cycle (IGCC) plants allow the combination of the production of hydrogen and electricity because coal gasification process produces a syngas that can be used for the production of both commodities. A hydrogen and electricity power plant has been denominated as HYPOGEN. This report starts by reviewing the basics of the coal gasification process and continues by trying to map all the technological options currently available in the market as well as possible future trends that can be included in a HYPOGEN system. Besides, it offers an overview of the operating conditions and outputs of each process in order to provide the modeller with a useful information tool enabling an easier analysis of compatibilities and implementation of the model. 119 refs., 53 figs., 38 tabs.

  20. An Optimal Power Flow (OPF) Method with Improved Power System Stability

    DEFF Research Database (Denmark)

    Su, Chi; Chen, Zhe

    2010-01-01

    This paper proposes an optimal power flow (OPF) method taking into account small signal stability as additional constraints. Particle swarm optimization (PSO) algorithm is adopted to realize the OPF process. The method is programmed in MATLAB and implemented to a nine-bus test power system which...... has large-scale wind power integration. The results show the ability of the proposed method to find optimal (or near-optimal) operating points in different cases. Based on these results, the analysis of the impacts of wind power integration on the system small signal stability has been conducted....

  1. SiC Power MOSFET with Improved Gate Dielectric

    Energy Technology Data Exchange (ETDEWEB)

    Sbrockey, Nick M; Tompa, Gary S; Spencer, Michael G; Chandrashekhar, Chandra MVS

    2010-08-23

    In this STTR program, Structured Materials Industries (SMI), and Cornell University are developing novel gate oxide technology, as a critical enabler for silicon carbide (SiC) devices. SiC is a wide bandgap semiconductor material, with many unique properties. SiC devices are ideally suited for high-power, highvoltage, high-frequency, high-temperature and radiation resistant applications. The DOE has expressed interest in developing SiC devices for use in extreme environments, in high energy physics applications and in power generation. The development of transistors based on the Metal Oxide Semiconductor Field Effect Transistor (MOSFET) structure will be critical to these applications.

  2. Recovery. Oxygen Transport Membrane-Based OxyCombustion for CO2 Capture from Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, Sean [Praxair Inc, Tonawanda, NY (United States); Geary, Joan [Praxair Inc, Tonawanda, NY (United States); Chakravrti, Shrikar [Praxair Inc, Tonawanda, NY (United States); Wilson, Jamie [Praxair Inc, Tonawanda, NY (United States); Christie, Max [Praxair Inc, Tonawanda, NY (United States); Peck, John [Praxair Inc, Tonawanda, NY (United States); Li, Juan [Praxair Inc, Tonawanda, NY (United States); Lane, Jonathan [Praxair Inc, Tonawanda, NY (United States); Gonzalez, Javier [Praxair Inc, Tonawanda, NY (United States); Lu, Yunxiang [Praxair Inc, Tonawanda, NY (United States); Biradar, Mahesh [Praxair Inc, Tonawanda, NY (United States); Robinson, Chuck [Praxair Inc, Tonawanda, NY (United States); Lin, Jiefeng [Praxair Inc, Tonawanda, NY (United States); Plonczak, Pawel [Praxair Inc, Tonawanda, NY (United States); Lu, Zigui [Praxair Inc, Tonawanda, NY (United States); Swami, Sadashiv [Praxair Inc, Tonawanda, NY (United States); Stuckert, Ines [Praxair Inc, Tonawanda, NY (United States)

    2015-12-22

    This Final report documents and summarizes all of the work performed for the DOE award DE-FC26-07NT43088 during the period from April 2007 - June 2012. This report outlines accomplishments for the following tasks: Task 1 – Process and Systems Engineering, Task 2 – OTM Performance Improvement, Task 3 – OTM Manufacturing Development, Task 4 - Laboratory Scale Testing and Task 5 – Project Management.

  3. Capture reactions

    NARCIS (Netherlands)

    Endt, P.M.

    1956-01-01

    Capture reactions will be considered here from the viewpoint of the nuclear spectroscopist. Especially important to him are the capture of neutrons, protons, and alpha particles, which may proceed through narrow resonances, offering a well defined initial state for the subsequent deexcitation proces

  4. New reactor technology: safety improvements in nuclear power systems.

    Science.gov (United States)

    Corradini, M L

    2007-11-01

    Almost 450 nuclear power plants are currently operating throughout the world and supplying about 17% of the world's electricity. These plants perform safely, reliably, and have no free-release of byproducts to the environment. Given the current rate of growth in electricity demand and the ever growing concerns for the environment, nuclear power can only satisfy the need for electricity and other energy-intensive products if it can demonstrate (1) enhanced safety and system reliability, (2) minimal environmental impact via sustainable system designs, and (3) competitive economics. The U.S. Department of Energy with the international community has begun research on the next generation of nuclear energy systems that can be made available to the market by 2030 or earlier, and that can offer significant advances toward these challenging goals; in particular, six candidate reactor system designs have been identified. These future nuclear power systems will require advances in materials, reactor physics, as well as thermal-hydraulics to realize their full potential. However, all of these designs must demonstrate enhanced safety above and beyond current light water reactor systems if the next generation of nuclear power plants is to grow in number far beyond the current population. This paper reviews the advanced Generation-IV reactor systems and the key safety phenomena that must be considered to guarantee that enhanced safety can be assured in future nuclear reactor systems.

  5. Cyclodissipativity and Power Factor Improvement for Full Nonlinear Loads

    NARCIS (Netherlands)

    Puerto-Flores, Dunstano del; Ortega, Romeo; Scherpen, Jacquelien M.A.; Edelmayer, András

    2010-01-01

    In recent research, a cyclodissipativity characterization of the problem of power factor compensation (PFC) for nonlinear loads with non-sinusoidal source voltage has been presented. Using this characterization the classical capacitor and inductor compensators can be interpreted in terms of energy e

  6. Ferrite Loaded Coils for Improved Wireless Power Transfer Efficiency

    Science.gov (United States)

    2015-09-01

    Department of Defense or the U.S. Government. IRB Protocol number ____N/A____. 12a. DISTRIBUTION / AVAILABILITY STATEMENT Approved for public...Series on Innovative Wireless Power Transmission: Technologies, Systems, and Applications, Kyoto , Japan, 2011, pp. 73–76. [15] Z. Ullah, A. Shahid, and

  7. CO2捕集装置与机组集成模拟研究%Integration of CO2 capture device and power plant:numerical simulation

    Institute of Scientific and Technical Information of China (English)

    吕太; 马俊昆朋; 韩国夫; 刘练波; 牛红伟; 郜时旺

    2015-01-01

    At present,the maln CO2 capture technology for power plants is post combustion CO2 capture, which has advantages of low cost in reforming and high capture efficiency.Taking the HG-1793/26.15-YM1 boiler in an ultra supercritical 600 MW unit as an example,the Thermoflow software was adopted to carry out simulation investigation on the combustion system,steam water system and cooling system in de-tall,and the system integrated scheme was put forward.The results show that,with the CO2 capture effi-ciency of 90%,the integrated unit's net efficiency will decrease by 10.87%,the coal consumption will in-crease by 17.61%,the CO2 emission will reduce to 90.55 g/(kW•h)and the SOx emission will also drop from 0.042 2 g/(kW•h)to near-zero.%电厂CO2捕集技术主要以燃烧后 CO2捕集技术为主,其具有改造成本低、捕集效率高等特点.以超超临界600 MW 机组 HG-1793/26.15-YM1燃煤锅炉为例,利用 Thermoflow 软件,分别对燃烧系统、汽水系统、冷却系统进行模拟计算,提出了 CO2捕集装置与现役超临界机组的集成优选方案.结果表明:脱碳机组集成后,CO2捕集效率为90%时,集成机组净效率下降10.87%,燃煤量增加17.61%,CO2排放量降至90.55g/(kW•h),SOx 排放量由0.0422 g/(kW•h)降至接近0.

  8. Dynamic simulation and load-following control of an integrated gasification combined cycle (IGCC) power plant with CO{sub 2} capture

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharyya, D,; Turton, R.; Zitney, S.

    2012-01-01

    pressure control. For maintaining the desired CO{sub 2} capture rate while load-following, a linear model predictive controller (LMPC) is implemented in MATLAB®. A combined process and disturbance model is identified by considering a number of model forms and choosing the final model based on an information-theoretic criterion. The performance of the LMPC is found to be superior to the conventional PID control for maintaining CO{sub 2} capture rates in an IGCC power plant while load following.

  9. Power density improvement of the power conditioning circuit for combined piezoelectric and electrodynamic generators

    Science.gov (United States)

    Zessin, H.; Spies, P.; Mateu, L.

    2016-11-01

    In this study, we report a power management circuit for a combined piezoelectric- electrodynamic generator. A piezoelectric element is bonded to a spring steel cantilever beam and a magnet, used as tip mass, oscillates through a coil. This principle creates the combined generator. A test setup has been created to automate the characterization of the piezoelectric generator and its power management circuit. Three different power management circuits for the piezoelectric part of the combined generator have been analysed: a bridge rectifier, an SSHI circuit with an external inductance and an SSHI circuit which utilizes the coil of the electrodynamic generator as circuit element. The three circuits are compared in terms of their output power, efficiency and power density. The SSHI circuit with an external inductance has the highest output power and efficiency, followed by the SSHI circuit with the electrodynamic generator coil. The power density of the bridge rectifier is the highest but for higher efficiency the power density of the SSHI circuit with the coil of the electromagnetic generator reaches the best results.

  10. Electric Vehicles for Improved Operation of Power Systems with High Wind Power Penetration

    DEFF Research Database (Denmark)

    Larsen, Esben; Chandrashekhara, Divya K; Østergaard, Jacob

    2008-01-01

    In a power system with a high share of wind energy the wind fluctuation causes a variation in the power generation, which must be compensated from other sources. The situation in Denmark with a penetration of more than 20% wind in yearly average is presented. The introduction of electric drive ve...

  11. Hands-free image capture, data tagging and transfer using Google Glass: a pilot study for improved wound care management.

    Science.gov (United States)

    Aldaz, Gabriel; Shluzas, Lauren Aquino; Pickham, David; Eris, Ozgur; Sadler, Joel; Joshi, Shantanu; Leifer, Larry

    2015-01-01

    Chronic wounds, including pressure ulcers, compromise the health of 6.5 million Americans and pose an annual estimated burden of $25 billion to the U.S. health care system. When treating chronic wounds, clinicians must use meticulous documentation to determine wound severity and to monitor healing progress over time. Yet, current wound documentation practices using digital photography are often cumbersome and labor intensive. The process of transferring photos into Electronic Medical Records (EMRs) requires many steps and can take several days. Newer smartphone and tablet-based solutions, such as Epic Haiku, have reduced EMR upload time. However, issues still exist involving patient positioning, image-capture technique, and patient identification. In this paper, we present the development and assessment of the SnapCap System for chronic wound photography. Through leveraging the sensor capabilities of Google Glass, SnapCap enables hands-free digital image capture, and the tagging and transfer of images to a patient's EMR. In a pilot study with wound care nurses at Stanford Hospital (n=16), we (i) examined feature preferences for hands-free digital image capture and documentation, and (ii) compared SnapCap to the state of the art in digital wound care photography, the Epic Haiku application. We used the Wilcoxon Signed-ranks test to evaluate differences in mean ranks between preference options. Preferred hands-free navigation features include barcode scanning for patient identification, Z(15) = -3.873, p Haiku, the SnapCap System was preferred for sterile image-capture technique, Z(16) = -3.873, p < 0.001, r = 0.68. Responses were divided with respect to image quality and overall ease of use. The study's results have contributed to the future implementation of new features aimed at enhancing mobile hands-free digital photography for chronic wound care.

  12. Multiethnic genetic association studies improve power for locus discovery.

    Directory of Open Access Journals (Sweden)

    Sara L Pulit

    Full Text Available To date, genome-wide association studies have focused almost exclusively on populations of European ancestry. These studies continue with the advent of next-generation sequencing, designed to systematically catalog and test low-frequency variation for a role in disease. A complementary approach would be to focus further efforts on cohorts of multiple ethnicities. This leverages the idea that population genetic drift may have elevated some variants to higher allele frequency in different populations, boosting statistical power to detect an association. Based on empirical allele frequency distributions from eleven populations represented in HapMap Phase 3 and the 1000 Genomes Project, we simulate a range of genetic models to quantify the power of association studies in multiple ethnicities relative to studies that exclusively focus on samples of European ancestry. In each of these simulations, a first phase of GWAS in exclusively European samples is followed by a second GWAS phase in any of the other populations (including a multiethnic design. We find that nontrivial power gains can be achieved by conducting future whole-genome studies in worldwide populations, where, in particular, African populations contribute the largest relative power gains for low-frequency alleles (<5% of moderate effect that suffer from low power in samples of European descent. Our results emphasize the importance of broadening genetic studies to worldwide populations to ensure efficient discovery of genetic loci contributing to phenotypic trait variability, especially for those traits for which large numbers of samples of European ancestry have already been collected and tested.

  13. Doping Li and K into Na2ZrO3 Sorbent to Improve Its CO2 Capture Capability

    Science.gov (United States)

    Duan, Yuhua

    Carbon dioxide is one of the major combustion products which once released into the air can contribute to global climate change. Solid sorbents have been reported in several previous studies to be promising candidates for CO2 sorbent applications due to their high CO2 absorption capacities at moderate working temperatures. However, at a given CO2 pressure, the turnover temperature (Tt) of an individual solid capture CO2 reaction is fixed and may be outside the operating temperature range (ΔTo) for a particularly capture technology. In order to shift such Tt for a solid into the range of ΔTo, its corresponding thermodynamic property must be changed by changing its structure by reacting (mixing) with other materials or doping with other elements. As an example, by combining thermodynamic database searching with ab initio thermodynamics calculations, in this work, we explored the Li- and K-doping effects on the Tt shifts of Na2ZrO3 at different doping levels. The obtained results showed that compared to pure Na2ZrO3, the Li- and K-doped mixtures Na2-αMαZrO3 (M =Li, K) have lower Tt and higher CO2 capture capacities.

  14. 76 FR 4147 - Putnam-Cumberland, TN-Improve Power Supply

    Science.gov (United States)

    2011-01-24

    ... Putnam-Cumberland, TN--Improve Power Supply AGENCY: Tennessee Valley Authority. ACTION: Notice of intent... supply improvements in the Putnam and Cumberland region of east-central Tennessee. The purpose of the... approximately 16,000 miles of transmission lines. TVA supplies bulk electric power to Cumberland and...

  15. Improving Free-Piston Stirling Engine Specific Power

    Science.gov (United States)

    Briggs, Maxwell H.

    2015-01-01

    This work uses analytical methods to demonstrate the potential benefits of optimizing piston and/or displacer motion in a Stirling engine. Isothermal analysis was used to show the potential benefits of ideal motion in ideal Stirling engines. Nodal analysis is used to show that ideal piston and displacer waveforms are not optimal in real Stirling engines. Constrained optimization was used to identify piston and displacer waveforms that increase Stirling engine specific power.

  16. IMPROVEMENT OF ELECTROCHEMICAL PROCESSES IN HYDROGEN POWER ENGINEERING

    OpenAIRE

    Covaliova O.V.; Covaliov V.V.; Duca Gh.G.; Ivanov M. V.

    2011-01-01

    The possibility is studied of using the three-dimensional voluminous-porous electrodes made of the carbonic-fibrous materials and foamy metals, which surface is covered with Ni-Re alloy, for hydrogen electrochemical generation. Electrode surface modification makes it possible to obtain high reactive surface with low overvoltage of hydrogen evolution. The design is given of the developed compact electrochemical reactors for hydrogen power engineering. The method is described of oxygen-hydrogen...

  17. Improved electrical power production of thermally regenerative batteries using a poly(phenylene oxide) based anion exchange membrane

    Science.gov (United States)

    Rahimi, Mohammad; Zhu, Liang; Kowalski, Kelly L.; Zhu, Xiuping; Gorski, Christopher A.; Hickner, Michael A.; Logan, Bruce E.

    2017-02-01

    Thermally regenerative ammonia-based batteries (TRABs) can be used to harvest low-grade waste heat as electrical power. To improve TRAB performance, a series of benzyltrimethyl quaternary ammonium-functionalized poly(phenylene oxide) anion exchange membranes (BTMA-AEMs) were examined for their impact on performance relative to a commercial AEM (Selemion AMV). The synthesized AEMs had different degrees of functionalization (DF; 25% and 40%), and thicknesses (50, 100 and 150 μm). Power and energy densities were shown to be a function of both DF and membrane thickness. The power density of TRAB increased by 31% using a BTMA-AEM (40% DF, 50 μm thick; 106 ± 7 W m-2) compared to the Selemion (81 ± 5 W m-2). Moreover, the energy density increased by 13% when using a BTMA-based membrane (25% DF, 150 μm thick; 350 Wh m-3) compared to the Selemion membrane (311 Wh m-3). The thermal-electric conversion efficiency improved to 0.97% with the new membrane compared to 0.86% for the Selemion. This energy recovery was 7.0% relative to the Carnot efficiency, which was 1.8 times greater than the highest previously reported value of a system used to capture low-grade waste heat as electricity.

  18. Improved Reliability of Single-Phase PV Inverters by Limiting the Maximum Feed-in Power

    DEFF Research Database (Denmark)

    Yang, Yongheng; Wang, Huai; Blaabjerg, Frede

    2014-01-01

    . The CPG control strategy is activated only when the DC input power from PV panels exceeds a specific power limit. It enables to limit the maximum feed-in power to the electric grids and also to improve the utilization of PV inverters. As a further study, this paper investigates the reliability performance...... of the power devices (e.g. IGBTs) used in PV inverters with the CPG control under different feed-in power limits. A long-term mission profile (i.e. solar irradiance and ambient temperature) based stress analysis approach is extended and applied to obtain the yearly electrical and thermal stresses of the power...

  19. Power Output Improvement of PV Module for Agricultural Use by Using Inexpensive Sunlight Concentrator

    Institute of Scientific and Technical Information of China (English)

    NISHIMURA Ryo

    2010-01-01

    PV modules are used as stand alone power sources for agricultural equipments such as lifting pumps in farms,where the power infrastructure is not yet improved.In order to expand the agricultural use of PV module,the cost of PV generation should be reduced.In this paper,the power output performance of a commercial PV module was improved by using a sunlight concentrator that could be assembled inexpensively and a simple sun-tracking method.

  20. Impact of Improved Solar Forecasts on Bulk Power System Operations in ISO-NE: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Brancucci Martinez-Anido, C.; Florita, A.; Hodge, B. M.

    2014-09-01

    The diurnal nature of solar power is made uncertain by variable cloud cover and the influence of atmospheric conditions on irradiance scattering processes. Its forecasting has become increasingly important to the unit commitment and dispatch process for efficient scheduling of generators in power system operations. This study examines the value of improved solar power forecasting for the Independent System Operator-New England system. The results show how 25% solar power penetration reduces net electricity generation costs by 22.9%.

  1. Improve your word power a concise way to increase your word power

    CERN Document Server

    Sawhney, Clifford

    2012-01-01

    A concise way to increase your word power English is a unique language which has innumerable great poets and authors from the past as well as the present, who have contributed profusely to its rich heritage….

  2. Improvement of Capture Compound Mass Spectrometry Technology (CCMS for the Profiling of Human Kinases by Combination with 2D LC-MS/MS

    Directory of Open Access Journals (Sweden)

    Jenny J. Fischer

    2011-01-01

    Full Text Available An increasingly popular and promising field in functional proteomics is the isolation of proteome subsets based on small molecule-protein interactions. One platform approach in this field are Capture Compounds that contain a small molecule of interest to bind target proteins, a photo-activatable reactivity function to covalently trap bound proteins, and a sorting function to isolate captured protein conjugates from complex biological samples for direct protein identification by liquid chromatography/mass spectrometry (nLC-MS/MS. In this study we used staurosporine as a selectivity group for analysis in HepG2 cells derived from human liver. In the present study, we combined the functional isolation of kinases with different separation workflows of automated split-free nanoflow liquid chromatography prior to mass spectrometric analysis. Two different CCMS setups, CCMS technology combined with 1D LC-MS and 2D LC-MS, were compared regarding the total number of kinase identifications. By extending the chromatographic separation of the tryptic digested captured proteins from 1D LC linear gradients to 2D LC we were able to identify 97 kinases. This result is similar to the 1D LC setup we previously reported but this time 4 times less input material was needed. This makes CCMS of kinases an even more powerful tool for the proteomic profiling of this important protein family.

  3. Improved methods for capture, extraction, and quantitative assay of environmental DNA from Asian bigheaded carp (Hypophthalmichthys spp.).

    Science.gov (United States)

    Turner, Cameron R; Miller, Derryl J; Coyne, Kathryn J; Corush, Joel

    2014-01-01

    Indirect, non-invasive detection of rare aquatic macrofauna using aqueous environmental DNA (eDNA) is a relatively new approach to population and biodiversity monitoring. As such, the sensitivity of monitoring results to different methods of eDNA capture, extraction, and detection is being investigated in many ecosystems and species. One of the first and largest conservation programs with eDNA-based monitoring as a central instrument focuses on Asian bigheaded carp (Hypophthalmichthys spp.), an invasive fish spreading toward the Laurentian Great Lakes. However, the standard eDNA methods of this program have not advanced since their development in 2010. We developed new, quantitative, and more cost-effective methods and tested them against the standard protocols. In laboratory testing, our new quantitative PCR (qPCR) assay for bigheaded carp eDNA was one to two orders of magnitude more sensitive than the existing endpoint PCR assays. When applied to eDNA samples from an experimental pond containing bigheaded carp, the qPCR assay produced a detection probability of 94.8% compared to 4.2% for the endpoint PCR assays. Also, the eDNA capture and extraction method we adapted from aquatic microbiology yielded five times more bigheaded carp eDNA from the experimental pond than the standard method, at a per sample cost over forty times lower. Our new, more sensitive assay provides a quantitative tool for eDNA-based monitoring of bigheaded carp, and the higher-yielding eDNA capture and extraction method we describe can be used for eDNA-based monitoring of any aquatic species.

  4. Improved methods for capture, extraction, and quantitative assay of environmental DNA from Asian bigheaded carp (Hypophthalmichthys spp..

    Directory of Open Access Journals (Sweden)

    Cameron R Turner

    Full Text Available Indirect, non-invasive detection of rare aquatic macrofauna using aqueous environmental DNA (eDNA is a relatively new approach to population and biodiversity monitoring. As such, the sensitivity of monitoring results to different methods of eDNA capture, extraction, and detection is being investigated in many ecosystems and species. One of the first and largest conservation programs with eDNA-based monitoring as a central instrument focuses on Asian bigheaded carp (Hypophthalmichthys spp., an invasive fish spreading toward the Laurentian Great Lakes. However, the standard eDNA methods of this program have not advanced since their development in 2010. We developed new, quantitative, and more cost-effective methods and tested them against the standard protocols. In laboratory testing, our new quantitative PCR (qPCR assay for bigheaded carp eDNA was one to two orders of magnitude more sensitive than the existing endpoint PCR assays. When applied to eDNA samples from an experimental pond containing bigheaded carp, the qPCR assay produced a detection probability of 94.8% compared to 4.2% for the endpoint PCR assays. Also, the eDNA capture and extraction method we adapted from aquatic microbiology yielded five times more bigheaded carp eDNA from the experimental pond than the standard method, at a per sample cost over forty times lower. Our new, more sensitive assay provides a quantitative tool for eDNA-based monitoring of bigheaded carp, and the higher-yielding eDNA capture and extraction method we describe can be used for eDNA-based monitoring of any aquatic species.

  5. Improved Methods for Capture, Extraction, and Quantitative Assay of Environmental DNA from Asian Bigheaded Carp (Hypophthalmichthys spp.)

    Science.gov (United States)

    Turner, Cameron R.; Miller, Derryl J.; Coyne, Kathryn J.; Corush, Joel

    2014-01-01

    Indirect, non-invasive detection of rare aquatic macrofauna using aqueous environmental DNA (eDNA) is a relatively new approach to population and biodiversity monitoring. As such, the sensitivity of monitoring results to different methods of eDNA capture, extraction, and detection is being investigated in many ecosystems and species. One of the first and largest conservation programs with eDNA-based monitoring as a central instrument focuses on Asian bigheaded carp (Hypophthalmichthys spp.), an invasive fish spreading toward the Laurentian Great Lakes. However, the standard eDNA methods of this program have not advanced since their development in 2010. We developed new, quantitative, and more cost-effective methods and tested them against the standard protocols. In laboratory testing, our new quantitative PCR (qPCR) assay for bigheaded carp eDNA was one to two orders of magnitude more sensitive than the existing endpoint PCR assays. When applied to eDNA samples from an experimental pond containing bigheaded carp, the qPCR assay produced a detection probability of 94.8% compared to 4.2% for the endpoint PCR assays. Also, the eDNA capture and extraction method we adapted from aquatic microbiology yielded five times more bigheaded carp eDNA from the experimental pond than the standard method, at a per sample cost over forty times lower. Our new, more sensitive assay provides a quantitative tool for eDNA-based monitoring of bigheaded carp, and the higher-yielding eDNA capture and extraction method we describe can be used for eDNA-based monitoring of any aquatic species. PMID:25474207

  6. Modeling and optimization of a modified claus process as part of an integrted gasification combined cycle (IGCC) power plant with CO2 capture

    Energy Technology Data Exchange (ETDEWEB)

    Jones, D.; Bhattacharyya, D.; Turton, R.; Zitney, S.

    2011-01-01

    The modified Claus process is one of the most common technologies for sulfur recovery from acid gas streams. Important design criteria for the Claus unit, when part of an Integrated Gasification Combined Cycle (IGCC) power plant, are the ability to destroy ammonia completely and recover sulfur thoroughly from a relatively low purity acid gas stream without sacrificing flame stability. Due to these criteria, modifications are often required to the conventional process, resulting in a modified Claus process. For the studies discussed here, these modifications include the use of a 95% pure oxygen stream as the oxidant, a split flow configuration, and the preheating of the feeds with the intermediate pressure steam generated in the waste heat boiler (WHB). In the future, for IGCC plants with CO2 capture, the Claus unit must satisfy emission standards without sacrificing the plant efficiency in the face of typical disturbances of an IGCC plant such as rapid change in the feed flowrates due to load-following and wide changes in the feed composition because of changes in the coal feed to the gasifier. The Claus unit should be adequately designed and efficiently operated to satisfy these objectives. Even though the Claus process has been commercialized for decades, most papers concerned with the modeling of the Claus process treat the key reactions as equilibrium reactions. Such models are validated by manipulating the temperature approach to equilibrium for a set of steady-state operating data, but are of limited use for dynamic studies. One of the objectives of this study is to develop a model that can be used for dynamic studies. In a Claus process, especially in the furnace and the WHB, many reactions may take place. In this work, a set of linearly independent reactions has been identified and kinetic models of the furnace flame and anoxic zones, WHB, and catalytic reactors have been developed. To facilitate the modeling of the Claus furnace, a four-stage method was

  7. Rigorous Kinetic Modeling, Optimization, and Operability Studies of a Modified Claus Unit for an Integrated Gasification Combined Cycle (IGCC) Power Plant with CO{sub 2} Capture

    Energy Technology Data Exchange (ETDEWEB)

    Jones, Dustin; Bhattacharyya, Debangsu; Turton, Richard; Zitney, Stephen E

    2011-12-15

    The modified Claus process is one of the most common technologies for sulfur recovery from acid gas streams. Important design criteria for the Claus unit, when part of an Integrated Gasification Combined Cycle (IGCC) power plant, are the ability to destroy ammonia completely and the ability to recover sulfur thoroughly from a relatively low purity acid gas stream without sacrificing flame stability. Because of these criteria, modifications to the conventional process are often required, resulting in a modified Claus process. For the studies discussed here, these modifications include the use of a 95% pure oxygen stream as the oxidant, a split flow configuration, and the preheating of the feeds with the intermediate pressure steam generated in the waste heat boiler (WHB). In the future, for IGCC plants with CO{sub 2} capture, the Claus unit must satisfy emission standards without sacrificing the plant efficiency in the face of typical disturbances of an IGCC plant, such as rapid change in the feed flow rates due to load-following and wide changes in the feed composition because of changes in the coal feed to the gasifier. The Claus unit should be adequately designed and efficiently operated to satisfy these objectives. Even though the Claus process has been commercialized for decades, most papers concerned with the modeling of the Claus process treat the key reactions as equilibrium reactions. Such models are validated by manipulating the temperature approach to equilibrium for a set of steady-state operating data, but they are of limited use for dynamic studies. One of the objectives of this study is to develop a model that can be used for dynamic studies. In a Claus process, especially in the furnace and the WHB, many reactions may take place. In this work, a set of linearly independent reactions has been identified, and kinetic models of the furnace flame and anoxic zones, WHB, and catalytic reactors have been developed. To facilitate the modeling of the Claus

  8. Rigorous Kinetic Modeling and Optimization Study of a Modified Claus Unit for an Integrated Gasification Combined Cycle (IGCC) Power Plant with CO{sub 2} Capture

    Energy Technology Data Exchange (ETDEWEB)

    Jones, Dustin; Bhattacharyya, Debangsu; Turton, Richard; Zitney, Stephen E.

    2012-02-08

    The modified Claus process is one of the most common technologies for sulfur recovery from acid gas streams. Important design criteria for the Claus unit, when part of an Integrated Gasification Combined Cycle (IGCC) power plant, are the ability to destroy ammonia completely and the ability to recover sulfur thoroughly from a relatively low purity acid gas stream without sacrificing flame stability. Because of these criteria, modifications to the conventional process are often required, resulting in a modified Claus process. For the studies discussed here, these modifications include the use of a 95% pure oxygen stream as the oxidant, a split flow configuration, and the preheating of the feeds with the intermediate pressure steam generated in the waste heat boiler (WHB). In the future, for IGCC plants with CO{sub 2} capture, the Claus unit must satisfy emission standards without sacrificing the plant efficiency in the face of typical disturbances of an IGCC plant, such as rapid change in the feed flow rates due to load-following and wide changes in the feed composition because of changes in the coal feed to the gasifier. The Claus unit should be adequately designed and efficiently operated to satisfy these objectives. Even though the Claus process has been commercialized for decades, most papers concerned with the modeling of the Claus process treat the key reactions as equilibrium reactions. Such models are validated by manipulating the temperature approach to equilibrium for a set of steady-state operating data, but they are of limited use for dynamic studies. One of the objectives of this study is to develop a model that can be used for dynamic studies. In a Claus process, especially in the furnace and the WHB, many reactions may take place. In this work, a set of linearly independent reactions has been identified, and kinetic models of the furnace flame and anoxic zones, WHB, and catalytic reactors have been developed. To facilitate the modeling of the Claus

  9. Hands-free image capture, data tagging and transfer using Google Glass: a pilot study for improved wound care management.

    Directory of Open Access Journals (Sweden)

    Gabriel Aldaz

    Full Text Available Chronic wounds, including pressure ulcers, compromise the health of 6.5 million Americans and pose an annual estimated burden of $25 billion to the U.S. health care system. When treating chronic wounds, clinicians must use meticulous documentation to determine wound severity and to monitor healing progress over time. Yet, current wound documentation practices using digital photography are often cumbersome and labor intensive. The process of transferring photos into Electronic Medical Records (EMRs requires many steps and can take several days. Newer smartphone and tablet-based solutions, such as Epic Haiku, have reduced EMR upload time. However, issues still exist involving patient positioning, image-capture technique, and patient identification. In this paper, we present the development and assessment of the SnapCap System for chronic wound photography. Through leveraging the sensor capabilities of Google Glass, SnapCap enables hands-free digital image capture, and the tagging and transfer of images to a patient's EMR. In a pilot study with wound care nurses at Stanford Hospital (n=16, we (i examined feature preferences for hands-free digital image capture and documentation, and (ii compared SnapCap to the state of the art in digital wound care photography, the Epic Haiku application. We used the Wilcoxon Signed-ranks test to evaluate differences in mean ranks between preference options. Preferred hands-free navigation features include barcode scanning for patient identification, Z(15 = -3.873, p < 0.001, r = 0.71, and double-blinking to take photographs, Z(13 = -3.606, p < 0.001, r = 0.71. In the comparison between SnapCap and Epic Haiku, the SnapCap System was preferred for sterile image-capture technique, Z(16 = -3.873, p < 0.001, r = 0.68. Responses were divided with respect to image quality and overall ease of use. The study's results have contributed to the future implementation of new features aimed at enhancing mobile hands-free digital

  10. IMPROVEMENT OF ELECTROCHEMICAL PROCESSES IN HYDROGEN POWER ENGINEERING

    Directory of Open Access Journals (Sweden)

    Covaliova O.V.

    2011-04-01

    Full Text Available The possibility is studied of using the three-dimensional voluminous-porous electrodes made of the carbonic-fibrous materials and foamy metals, which surface is covered with Ni-Re alloy, for hydrogen electrochemical generation. Electrode surface modification makes it possible to obtain high reactive surface with low overvoltage of hydrogen evolution. The design is given of the developed compact electrochemical reactors for hydrogen power engineering. The method is described of oxygen-hydrogen mixture separation in the water electrolysis processes.

  11. Hybrid aqueous capacitors with improved energy/power performance

    Directory of Open Access Journals (Sweden)

    Jakub Menzel

    2015-12-01

    Full Text Available This work reports on a high-voltage, hybrid capacitor involving two separate redox reactions. Aqueous solutions of Mg(NO32 and KI have been used for negative and positive electrode, respectively. Adjusting pH=2 for electrode (+ with KI solution and modifying Mg(NO32 solution to pH=9 for negative side play a crucial role for a stable long-term operation of capacitor at enhanced voltage. A benefit from such a construction is a pseudocapacitive contribution from hydrogen sorption reaction on the negative electrode and high iodine/iodide activity on the positive electrode, enhancing the energy with no remarkable impact on the power profile. Proposed solution allows a high voltage (1.8 V to be reached and thereby high power and energy performance (~20 W h/kg at 1 kW/kg to be obtained. High long-term stability has been confirmed by floating and galvanostatic tests.

  12. Improvement of Transient Stability of Power System by Thyristor Controlled Phase Shifter Transformer

    Directory of Open Access Journals (Sweden)

    Prechanon Kumkratug

    2010-01-01

    Full Text Available Problem statement: The improvement of transient stability of the power system was one of the most challenging research areas in power engineer. Approach: This study presents the method to improve transient stability of power system by Thyristor Controlled Phase Shifter Transformer (TCPST. The mathematical model of power system equipped with a TCPST was systematically derived. The parameters of TCPST are modeled into power flow equation and thus it was used to determine control strategy. The swing curves of the three phase faulted power system without and with a TCPST are tested and compared in various cases. Results: The swing curve of system without a TCPST gets increases monotonically and thus the system can be considered as unstable whereas the swing curves of system with a TCPST can return to stable equilibrium point. Conclusion: From the simulation results, the TCPST can increase transient stability of power system.

  13. Leveraging the power of music to improve science education

    Science.gov (United States)

    Crowther, Gregory J.; McFadden, Tom; Fleming, Jean S.; Davis, Katie

    2016-01-01

    We assessed the impact of music videos with science-based lyrics on content knowledge and attitudes in a three-part experimental research study of over 1000 participants (mostly K-12 students). In Study A, 13 of 15 music videos were followed by statistically significant improvements on questions about material covered in the videos, while performance on 'bonus questions' not covered by the videos did not improve. Video-specific improvement was observed in both basic knowledge and genuine comprehension (levels 1 and 2 of Bloom's taxonomy, respectively) and after both lyrics-only and visually rich versions of some videos. In Study B, musical versions of additional science videos were not superior to non-musical ones in their immediate impact on content knowledge, though musical versions were significantly more enjoyable. In Study C, a non-musical video on fossils elicited greater immediate test improvement than the musical version ('Fossil Rock Anthem'); however, viewers of the music video enjoyed a modest advantage on a delayed post-test administered 28 days later. Music video viewers more frequently rated their video as 'fun', and seemed more likely to revisit and/or share the video. Our findings contribute to a broader dialogue on promising new pedagogical strategies in science education.

  14. Sensor placement algorithm development to maximize the efficiency of acid gas removal unit for integrated gasification combined cycle (IGCC) power plant with CO{sub 2} capture

    Energy Technology Data Exchange (ETDEWEB)

    Paul, P.; Bhattacharyya, D.; Turton, R.; Zitney, S.

    2012-01-01

    Future integrated gasification combined cycle (IGCC) power plants with CO{sub 2} capture will face stricter operational and environmental constraints. Accurate values of relevant states/outputs/disturbances are needed to satisfy these constraints and to maximize the operational efficiency. Unfortunately, a number of these process variables cannot be measured while a number of them can be measured, but have low precision, reliability, or signal-to-noise ratio. In this work, a sensor placement (SP) algorithm is developed for optimal selection of sensor location, number, and type that can maximize the plant efficiency and result in a desired precision of the relevant measured/unmeasured states. In this work, an SP algorithm is developed for an selective, dual-stage Selexol-based acid gas removal (AGR) unit for an IGCC plant with pre-combustion CO{sub 2} capture. A comprehensive nonlinear dynamic model of the AGR unit is developed in Aspen Plus Dynamics® (APD) and used to generate a linear state-space model that is used in the SP algorithm. The SP algorithm is developed with the assumption that an optimal Kalman filter will be implemented in the plant for state and disturbance estimation. The algorithm is developed assuming steady-state Kalman filtering and steady-state operation of the plant. The control system is considered to operate based on the estimated states and thereby, captures the effects of the SP algorithm on the overall plant efficiency. The optimization problem is solved by Genetic Algorithm (GA) considering both linear and nonlinear equality and inequality constraints. Due to the very large number of candidate sets available for sensor placement and because of the long time that it takes to solve the constrained optimization problem that includes more than 1000 states, solution of this problem is computationally expensive. For reducing the computation time, parallel computing is performed using the Distributed Computing Server (DCS®) and the Parallel

  15. Sensor placement algorithm development to maximize the efficiency of acid gas removal unit for integrated gasifiction combined sycle (IGCC) power plant with CO2 capture

    Energy Technology Data Exchange (ETDEWEB)

    Paul, P.; Bhattacharyya, D.; Turton, R.; Zitney, S.

    2012-01-01

    Future integrated gasification combined cycle (IGCC) power plants with CO{sub 2} capture will face stricter operational and environmental constraints. Accurate values of relevant states/outputs/disturbances are needed to satisfy these constraints and to maximize the operational efficiency. Unfortunately, a number of these process variables cannot be measured while a number of them can be measured, but have low precision, reliability, or signal-to-noise ratio. In this work, a sensor placement (SP) algorithm is developed for optimal selection of sensor location, number, and type that can maximize the plant efficiency and result in a desired precision of the relevant measured/unmeasured states. In this work, an SP algorithm is developed for an selective, dual-stage Selexol-based acid gas removal (AGR) unit for an IGCC plant with pre-combustion CO{sub 2} capture. A comprehensive nonlinear dynamic model of the AGR unit is developed in Aspen Plus Dynamics® (APD) and used to generate a linear state-space model that is used in the SP algorithm. The SP algorithm is developed with the assumption that an optimal Kalman filter will be implemented in the plant for state and disturbance estimation. The algorithm is developed assuming steady-state Kalman filtering and steady-state operation of the plant. The control system is considered to operate based on the estimated states and thereby, captures the effects of the SP algorithm on the overall plant efficiency. The optimization problem is solved by Genetic Algorithm (GA) considering both linear and nonlinear equality and inequality constraints. Due to the very large number of candidate sets available for sensor placement and because of the long time that it takes to solve the constrained optimization problem that includes more than 1000 states, solution of this problem is computationally expensive. For reducing the computation time, parallel computing is performed using the Distributed Computing Server (DCS®) and the Parallel

  16. A Performance Improvement of Power Supply Module for Safety-related Controller

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong-Kyun; Yun, Dong-Hwa; Hwang, Sung-Jae; Lee, Myeong-Kyun; Yoo, Kwan-Woo [PONUTech Co., Seoul (Korea, Republic of)

    2015-10-15

    In this paper, in relation to voltage shortage state when power supply module is a slave mode, the performance improvement by modifying a PFC(Power Factor Correction) circuit is presented. With the modification of the PFC circuit, the performance improvement in respect of the voltage shortage state when the power supply module is a slave mode is checked. As a result, POSAFE-Q PLC can ensure the stability with the redundant power supply module. The purpose of this paper is to improve the redundant performance of power supply module(NSPS-2Q). It is one of components in POSAFE-Q which is a PLC(Programmable Logic Controller) that has been developed for the evaluation of safety-related. Power supply module provides a stable power in order that POSAFE-Q can be operated normally. It is possible to be mounted two power supply modules in POSAFE-Q for a redundant(Master/Slave) function. So that even if a problem occurs in one power supply module, another power supply module will provide a power to POSAFE-Q stably.

  17. Improving a Power Line Communications Standard with LDPC Codes

    Directory of Open Access Journals (Sweden)

    Hsu Christine

    2007-01-01

    Full Text Available We investigate a power line communications (PLC scheme that could be used to enhance the HomePlug 1.0 standard, specifically its ROBO mode which provides modest throughput for the worst case PLC channel. The scheme is based on using a low-density parity-check (LDPC code, in lieu of the concatenated Reed-Solomon and convolutional codes in ROBO mode. The PLC channel is modeled with multipath fading and Middleton's class A noise. Clipping is introduced to mitigate the effect of impulsive noise. A simple and effective method is devised to estimate the variance of the clipped noise for LDPC decoding. Simulation results show that the proposed scheme outperforms the HomePlug 1.0 ROBO mode and has lower computational complexity. The proposed scheme also dispenses with the repetition of information bits in ROBO mode to gain time diversity, resulting in 4-fold increase in physical layer throughput.

  18. CATARACT: Computer code for improving power calculations at NREL's high-flux solar furnace

    Science.gov (United States)

    Scholl, K.; Bingham, C.; Lewandowski, A.

    1994-01-01

    The High-Flux Solar Furnace (HFSF), operated by the National Renewable Energy Laboratory, uses a camera-based, flux-mapping system to analyze the distribution and to determine total power at the focal point. The flux-mapping system consists of a diffusively reflecting plate with seven circular foil calorimeters, a charge-coupled device (CCD) camera, an IBM-compatible personal computer with a frame-grabber board, and commercial image analysis software. The calorimeters provide flux readings that are used to scale the image captured from the plate by the camera. The image analysis software can estimate total power incident on the plate by integrating under the 3-dimensional image. Because of the physical layout of the HFSF, the camera is positioned at a 20 angle to the flux mapping plate normal. The foreshortening of the captured images that results represents a systematic error in the power calculations because the software incorrectly assumes the image is parallel to the camera's array. We have written a FORTRAN computer program called CATARACT (camera/target angle correction) that we use to transform the original flux-mapper image to a plane that is normal to the camera's optical axis. A description of the code and the results of experiments performed to verify it are presented. Also presented are comparisons of the total power available from the HFSF as determined from the flux mapping system and theoretical considerations.

  19. An Application of Six Sigma for Improving the Efficiency of Power Supply

    Directory of Open Access Journals (Sweden)

    Chang-Hsien Hsu

    2013-10-01

    Full Text Available Implementing the Six Sigma control method is to use define, measure, analyze, improve and control (DMAIC framework to improve the process from the beginning, emphasize the process management, reduce the process time, eliminate the defects, and increase the passing rate. The aims of this study is to apply Six Sigma control method with DMAIC framework to shorten the power supply over time in order to enhance the power supply efficiency in T. power company (TPC. The result showed that the power supply over time was reduced from 66% to 30% in the Construction Work Second Section.

  20. Design and Analysis of Multi Level D-STATCOM to Improve the Power Quality

    Directory of Open Access Journals (Sweden)

    Dinesh. Badavath,

    2014-01-01

    Full Text Available In the last decade, the electrical power quality issue has been the main concern of the power companies. Power quality is defined as the index which both the delivery and consumption of electric power affect on the performance of electrical apparatus. From a customer point of view, a power quality problem can be defined as any problem is manifested on voltage, current, or frequency deviation that results in power failure. The power electronics progressive, especially in flexible alternating-current transmission system (FACTS and custom power devices, affects power quality improvement. This paper presents an investigation of seven-Level Cascaded H - bridge (CHB Inverter as Distribution Static Compensator (DSTATCOM in Power System (PS for compensation of reactive power and harmonics. The advantages of CHB inverter are low harmonic distortion, reduced number of switches and suppression of switching losses. The DSTATCOM helps to improve the power factor and eliminate the Total Harmonics Distortion (THD drawn from a Non-Liner Diode Rectifier Load (NLDRL. The D-Q reference frame theory is used to generate the reference compensating currents for DSTATCOM while Proportional and Integral (PI control is used for capacitor dc voltage regulation. A CHB Inverter is considered for shunt compensation of a 11 Kv distribution system. Finally a level shifted PWM (LSPWM and phase shifted PWM (PSPWM techniques are adopted to investigate the performance of CHB Inverter. The results are obtained through Matlab/Simulink software package.

  1. Improving leadership through the power of words and music

    OpenAIRE

    Romanowska, Julia

    2014-01-01

    Background. Poor leadership is highly prevalent and associated with destructive processes in the workplace, including stress related ill health. Yet, the applied methods to improve leadership practices are rarely grounded in scientific research. The aim of this thesis is to test the effects of an art-based, yearlong leadership programme (Shibboleth) in comparison with a conventional programme. The Shibboleth concept was built upon a performance art, a collage of fragments of literary text and...

  2. A Switching-Mode Power Supply Design Tool to Improve Learning in a Power Electronics Course

    Science.gov (United States)

    Miaja, P. F.; Lamar, D. G.; de Azpeitia, M.; Rodriguez, A.; Rodriguez, M.; Hernando, M. M.

    2011-01-01

    The static design of ac/dc and dc/dc switching-mode power supplies (SMPS) relies on a simple but repetitive process. Although specific spreadsheets, available in various computer-aided design (CAD) programs, are widely used, they are difficult to use in educational applications. In this paper, a graphic tool programmed in MATLAB is presented,…

  3. Modeling,Analysis and Simulation ofThree Phase Hybrid Power Filter forPower Quality Improvement

    Directory of Open Access Journals (Sweden)

    Prashanta Kumar Das

    2012-05-01

    Full Text Available A three-phase hybrid series power filter is constituted by a series active filter and a passive filter connected in parallel with the load. The control strategy is based on the “dual formulation of the electric power vectorial theory”. The proposed algorithm eliminates the current harmonics of supply. It also improves the power factor and harmonic compensation features of the associated passive filter even if there is a change in system parameters.A shunt hybrid power filter is constituted by a shunt active filter and a passive filter connected in parallel with the load, is proposed with same control strategy. Simulations have been carried out on the MATLAB-SIMULINK platform with different loads and with variation in the source impedance.

  4. Robust C–C bonded porous networks with chemically designed functionalities for improved CO2 capture from flue gas

    Directory of Open Access Journals (Sweden)

    Damien Thirion

    2016-10-01

    Full Text Available Effective carbon dioxide (CO2 capture requires solid, porous sorbents with chemically and thermally stable frameworks. Herein, we report two new carbon–carbon bonded porous networks that were synthesized through metal-free Knoevenagel nitrile–aldol condensation, namely the covalent organic polymer, COP-156 and 157. COP-156, due to high specific surface area (650 m2/g and easily interchangeable nitrile groups, was modified post-synthetically into free amine- or amidoxime-containing networks. The modified COP-156-amine showed fast and increased CO2 uptake under simulated moist flue gas conditions compared to the starting network and usual industrial CO2 solvents, reaching up to 7.8 wt % uptake at 40 °C.

  5. Robust C-C bonded porous networks with chemically designed functionalities for improved CO2 capture from flue gas.

    Science.gov (United States)

    Thirion, Damien; Lee, Joo S; Özdemir, Ercan; Yavuz, Cafer T

    2016-01-01

    Effective carbon dioxide (CO2) capture requires solid, porous sorbents with chemically and thermally stable frameworks. Herein, we report two new carbon-carbon bonded porous networks that were synthesized through metal-free Knoevenagel nitrile-aldol condensation, namely the covalent organic polymer, COP-156 and 157. COP-156, due to high specific surface area (650 m(2)/g) and easily interchangeable nitrile groups, was modified post-synthetically into free amine- or amidoxime-containing networks. The modified COP-156-amine showed fast and increased CO2 uptake under simulated moist flue gas conditions compared to the starting network and usual industrial CO2 solvents, reaching up to 7.8 wt % uptake at 40 °C.

  6. Robust C–C bonded porous networks with chemically designed functionalities for improved CO2 capture from flue gas

    Science.gov (United States)

    Thirion, Damien; Lee, Joo S; Özdemir, Ercan

    2016-01-01

    Effective carbon dioxide (CO2) capture requires solid, porous sorbents with chemically and thermally stable frameworks. Herein, we report two new carbon–carbon bonded porous networks that were synthesized through metal-free Knoevenagel nitrile–aldol condensation, namely the covalent organic polymer, COP-156 and 157. COP-156, due to high specific surface area (650 m2/g) and easily interchangeable nitrile groups, was modified post-synthetically into free amine- or amidoxime-containing networks. The modified COP-156-amine showed fast and increased CO2 uptake under simulated moist flue gas conditions compared to the starting network and usual industrial CO2 solvents, reaching up to 7.8 wt % uptake at 40 °C. PMID:28144294

  7. Compensation for Power Quality Improvement in Electric Arc Furnace with Considering Economic Index

    Directory of Open Access Journals (Sweden)

    Ghazanfar Shahgholian

    2012-03-01

    Full Text Available In recent years, on the one hand with increasing application of nonlinear loads in power systems and no sinusoidal currents that extracted from system, and on the other hand increasing loads sensitive to power quality and destructive effects of nonlinear loads on power quality of power systems, compensation these loads has been converted to one of the main issues in power systems. The use of flexible AC transmission system (FACTS devices is one of the most progressive methods which are used for improving power quality. In this paper, series and parallel compensators of static synchronous compensator (STATCOM and dynamic voltage restorer (DVR are introduced and the comparison of these two in compensating of power quality phenomena from electric arc furnace is provided. STATCOM is a shunt active filter and DVR is a series active filter. Method which has been selected for control of every one of these devices is an optimal control way that it minimizes power losses.

  8. DS-CDMA system outer loop power control and improvement for multi-service

    Institute of Scientific and Technical Information of China (English)

    Guan Mingxiang; Guo Qing; Li Xing

    2008-01-01

    When a new user accesses the CDMA system, the load will change drastically, and therefore, the advanced outer loop power control (OLPC) technology has to be adopted to enrich the target signal interference ratio (SIR) and improve the system performance. The existing problems about DS-CDMA outer loop power control for multi-service are introduced and the power control theoretical model is analyzed. System simulation is adopted on how to obtain the theoretical performance and parameter optimization of the power control algorithm. The OLPC algorithm is improved and the performance comparisons between the old algorithm and the improved algorithm are given. The results show good performance of the improved OLPC algorithm and prove the validity of the improved method for multi-service.

  9. Improving the Output Power Stability of a High Concentration Photovoltaic System with Supercapacitors: A Preliminary Evaluation

    Directory of Open Access Journals (Sweden)

    Yu-Pei Huang

    2015-01-01

    Full Text Available The output power of a high concentration photovoltaic (HCPV system is very sensitive to fluctuating tracking errors and weather patterns. To help compensate this shortcoming, supercapacitors have been successfully incorporated into photovoltaic systems to improve their output power stability. This study examined the output power stability improvement of an HCPV module with a supercapacitor integrated into its circuit. Furthermore, the equivalent model of the experimental circuit is presented and analyzed. Experimental results suggest that integrating a supercapacitor into an HCPV module could improve its output power stability and further extend its acceptance angle. This paper provides preliminary data of the improvement and its evaluation method, which could be utilized for further improvements to an HCPV system.

  10. Power outage estimation for tropical cyclones: improved accuracy with simpler models.

    Science.gov (United States)

    Nateghi, Roshanak; Guikema, Seth; Quiring, Steven M

    2014-06-01

    In this article, we discuss an outage-forecasting model that we have developed. This model uses very few input variables to estimate hurricane-induced outages prior to landfall with great predictive accuracy. We also show the results for a series of simpler models that use only publicly available data and can still estimate outages with reasonable accuracy. The intended users of these models are emergency response planners within power utilities and related government agencies. We developed our models based on the method of random forest, using data from a power distribution system serving two states in the Gulf Coast region of the United States. We also show that estimates of system reliability based on wind speed alone are not sufficient for adequately capturing the reliability of system components. We demonstrate that a multivariate approach can produce more accurate power outage predictions.

  11. Development of Improved Burnable Poisons for Commercial Nuclear Power Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Renier, J.A.

    2002-04-17

    Burnable poisons are used in all modern nuclear reactors to permit higher loading of fuel without the necessity of an overly large control rod system. This not only permits a longer core life but can also be used to level the power distribution. Commercial nuclear reactors commonly use B{sub 4}C in separate non-fueled rods and more recently, zirconium boride coatings on the fuel pellets or gadolinium oxide mixed with the fuel. Although the advantages are great, there are problems with using these materials. Boron, which is an effective neutron absorber, transmutes to lithium and helium upon absorption of a neutron. Helium is insoluble and is eventually released to the interior of the fuel rod, where it produces an internal pressure. When sufficiently high, this pressure stress could cause separation of the cladding from the fuel, causing overly high centerline temperatures. Gadolinium has several very strongly absorbing isotopes, but not all have large cross sections and result in residual burnable poison reactivity worth at the end of the fuel life. Even if the amount of this residual absorber is small and the penalty in operation small, the cost of this penalty, even if only several days, can be very high. The objective of this investigation was to study the performance of single isotopes in order to reduce the residual negative reactivity left over at the end of the fuel cycle. Since the behavior of burnable poisons can be strongly influenced by their configuration, four forms for the absorbers were studied: homogeneously mixed with the fuel, mixed with only the outer one-third of the fuel pellet, coated on the perimeter of the fuel pellets, and alloyed with the cladding. In addition, the numbers of fuel rods containing burnable poison were chosen as 8, 16, 64, and 104. Other configurations were chosen for a few special cases. An enrichment of 4.5 wt% {sup 235}U was chosen for most cases for study in order to achieve a 4-year fuel cycle. A standard pressurized

  12. Matrix Converter Based Unified Power Quality Conditioner (MUPQC for Power Quality Improvement in a Utility

    Directory of Open Access Journals (Sweden)

    G.L. Valsala

    2014-05-01

    Full Text Available This study proposes a new approach of unified power quality conditioner which is made up of a matrix converter without energy storage devices to mitigate the current harmonics, voltage sags and swell. By connecting the matrix converter output terminals to the load side through series transformer and the input side of matrix converter is connected to the supply side with step up transformer. So a matrix converter injects the compensation voltage on the load-side, so it is possible to mitigate the voltage sag/swell problems, resulting in an efficient solution for mitigating voltage and current related power quality problems. Thus, the proposed topology can mitigate the voltage fluctuations and current harmonics without energy storage elements and the total harmonic distortion produced by the system also very low. It also reduced volume and cost, reduced capacitor power losses, together with higher reliability. The Space-Vector Modulation (SVM is used to control the matrix converter. MATLAB/SIMULINK based simulation results are presented to validate the approach.

  13. An Improved Method for Power-Line Reconstruction from Point Cloud Data

    Directory of Open Access Journals (Sweden)

    Bo Guo

    2016-01-01

    Full Text Available This paper presents a robust algorithm to reconstruct power-lines using ALS technology. Point cloud data are automatically classified into five target classes before reconstruction. In order to improve upon the defaults of only using the local shape properties of a single power-line span in traditional methods, the distribution properties of power-line group between two neighbor pylons and contextual information of related pylon objects are used to improve the reconstruction results. First, the distribution properties of power-line sets are detected using a similarity detection method. Based on the probability of neighbor points belonging to the same span, a RANSAC rule based algorithm is then introduced to reconstruct power-lines through two important advancements: reliable initial parameters fitting and efficient candidate sample detection. Our experiments indicate that the proposed method is effective for reconstruction of power-lines from complex scenarios.

  14. No extension of quantum theory can have improved predictive power.

    Science.gov (United States)

    Colbeck, Roger; Renner, Renato

    2011-08-02

    According to quantum theory, measurements generate random outcomes, in stark contrast with classical mechanics. This raises the question of whether there could exist an extension of the theory that removes this indeterminism, as suspected by Einstein, Podolsky and Rosen. Although this has been shown to be impossible, existing results do not imply that the current theory is maximally informative. Here we ask the more general question of whether any improved predictions can be achieved by any extension of quantum theory. Under the assumption that measurements can be chosen freely, we answer this question in the negative: no extension of quantum theory can give more information about the outcomes of future measurements than quantum theory itself. Our result has significance for the foundations of quantum mechanics, as well as applications to tasks that exploit the inherent randomness in quantum theory, such as quantum cryptography.

  15. Fundamentals of modern statistical methods substantially improving power and accuracy

    CERN Document Server

    Wilcox, Rand R

    2001-01-01

    Conventional statistical methods have a very serious flaw They routinely miss differences among groups or associations among variables that are detected by more modern techniques - even under very small departures from normality Hundreds of journal articles have described the reasons standard techniques can be unsatisfactory, but simple, intuitive explanations are generally unavailable Improved methods have been derived, but they are far from obvious or intuitive based on the training most researchers receive Situations arise where even highly nonsignificant results become significant when analyzed with more modern methods Without assuming any prior training in statistics, Part I of this book describes basic statistical principles from a point of view that makes their shortcomings intuitive and easy to understand The emphasis is on verbal and graphical descriptions of concepts Part II describes modern methods that address the problems covered in Part I Using data from actual studies, many examples are include...

  16. An improved harmony search algorithm for power economic load dispatch

    Energy Technology Data Exchange (ETDEWEB)

    Coelho, Leandro dos Santos [Pontifical Catholic Univ. of Parana, PUCPR, Industrial and Systems Engineering Graduate Program, PPGEPS, Imaculada Conceicao, 1155, 80215-901 Curitiba, PR (Brazil); Mariani, Viviana Cocco [Pontifical Catholic Univ. of Parana, PUCPR, Dept. of Mechanical Engineering, PPGEM, Imaculada Conceicao, 1155, 80215-901 Curitiba, PR (Brazil)

    2009-10-15

    A meta-heuristic algorithm called harmony search (HS), mimicking the improvisation process of music players, has been recently developed. The HS algorithm has been successful in several optimization problems. The HS algorithm does not require derivative information and uses stochastic random search instead of a gradient search. In addition, the HS algorithm is simple in concept, few in parameters, and easy in implementation. This paper presents an improved harmony search (IHS) algorithm based on exponential distribution for solving economic dispatch problems. A 13-unit test system with incremental fuel cost function taking into account the valve-point loading effects is used to illustrate the effectiveness of the proposed IHS method. Numerical results show that the IHS method has good convergence property. Furthermore, the generation costs of the IHS method are lower than those of the classical HS and other optimization algorithms reported in recent literature. (author)

  17. An improved harmony search algorithm for power economic load dispatch

    Energy Technology Data Exchange (ETDEWEB)

    Santos Coelho, Leandro dos [Pontifical Catholic University of Parana, PUCPR, Industrial and Systems Engineering Graduate Program, PPGEPS, Imaculada Conceicao, 1155, 80215-901 Curitiba, PR (Brazil)], E-mail: leandro.coelho@pucpr.br; Mariani, Viviana Cocco [Pontifical Catholic University of Parana, PUCPR, Department of Mechanical Engineering, PPGEM, Imaculada Conceicao, 1155, 80215-901 Curitiba, PR (Brazil)], E-mail: viviana.mariani@pucpr.br

    2009-10-15

    A meta-heuristic algorithm called harmony search (HS), mimicking the improvisation process of music players, has been recently developed. The HS algorithm has been successful in several optimization problems. The HS algorithm does not require derivative information and uses stochastic random search instead of a gradient search. In addition, the HS algorithm is simple in concept, few in parameters, and easy in implementation. This paper presents an improved harmony search (IHS) algorithm based on exponential distribution for solving economic dispatch problems. A 13-unit test system with incremental fuel cost function taking into account the valve-point loading effects is used to illustrate the effectiveness of the proposed IHS method. Numerical results show that the IHS method has good convergence property. Furthermore, the generation costs of the IHS method are lower than those of the classical HS and other optimization algorithms reported in recent literature.

  18. An Improved Harmony Search Algorithm for Power Distribution Network Planning

    Directory of Open Access Journals (Sweden)

    Wei Sun

    2015-01-01

    Full Text Available Distribution network planning because of involving many variables and constraints is a multiobjective, discrete, nonlinear, and large-scale optimization problem. Harmony search (HS algorithm is a metaheuristic algorithm inspired by the improvisation process of music players. HS algorithm has several impressive advantages, such as easy implementation, less adjustable parameters, and quick convergence. But HS algorithm still has some defects such as premature convergence and slow convergence speed. According to the defects of the standard algorithm and characteristics of distribution network planning, an improved harmony search (IHS algorithm is proposed in this paper. We set up a mathematical model of distribution network structure planning, whose optimal objective function is to get the minimum annual cost and constraint conditions are overload and radial network. IHS algorithm is applied to solve the complex optimization mathematical model. The empirical results strongly indicate that IHS algorithm can effectively provide better results for solving the distribution network planning problem compared to other optimization algorithms.

  19. STUDIES ON IGBT MODULE TO IMPROVE THE RELIABILITY OF POWER ELECTRONIC SYSTEMS

    DEFF Research Database (Denmark)

    Choi, Uimin

    As power electronic systems have gradually gained an important status in a wide range of industrial applications, there are increasing demands to improve the reliability and robustness of power electronic systems. The power electronic systems consist of various components, and among them, power...... that kills IGBT modules. Therefore, in order to improve the reliability of power electronic systems, reliability research on reliability-critical components regarding the major critical stressors are needed. In this PhD project, various researches on reliability of the IGBT module are performed from...... component level to converter level. It is divided into two main parts: the first part, which consists of Chapters 2 and 3, is reliability studies of the IGBT module regarding thermal stresses and the second part, composed of Chapters 4 and 5, discusses strategies to improve the reliability and availability...

  20. Biomechanics and hydrodynamics of prey capture in the Chinese giant salamander reveal a high-performance jaw-powered suction feeding mechanism

    Science.gov (United States)

    Heiss, Egon; Natchev, Nikolay; Gumpenberger, Michaela; Weissenbacher, Anton; Van Wassenbergh, Sam

    2013-01-01

    During the evolutionary transition from fish to tetrapods, a shift from uni- to bidirectional suction feeding systems followed a reduction in the gill apparatus. Such a shift can still be observed during metamorphosis of salamanders, although many adult salamanders retain their aquatic lifestyle and feed by high-performance suction. Unfortunately, little is known about the interplay between jaws and hyobranchial motions to generate bidirectional suction flows. Here, we study the cranial morphology, as well as kinematic and hydrodynamic aspects related to prey capture in the Chinese giant salamander (Andrias davidianus). Compared with fish and previously studied amphibians, A. davidianus uses an alternative suction mechanism that mainly relies on accelerating water by separating the ‘plates’ formed by the long and broad upper and lower jaw surfaces. Computational fluid dynamics simulations, based on three-dimensional morphology and kinematical data from high-speed videos, indicate that the viscerocranial elements mainly serve to accommodate the water that was given a sufficient anterior-to-posterior impulse beforehand by powerful jaw separation. We hypothesize that this modified way of generating suction is primitive for salamanders, and that this behaviour could have played an important role in the evolution of terrestrial life in vertebrates by releasing mechanical constraints on the hyobranchial system. PMID:23466557

  1. Coal-fuelled systems for peaking power with 100% CO2 capture through integration of solid oxide fuel cells with compressed air energy storage

    Science.gov (United States)

    Nease, Jake; Adams, Thomas A.

    2014-04-01

    In this study, a coal-fuelled integrated solid oxide fuel cell (SOFC) and compressed air energy storage (CAES) system in a load-following power production scenario is discussed. Sixteen SOFC-based plants with optional carbon capture and sequestration (CCS) and syngas shifting steps are simulated and compared to a state-of-the-art supercritical pulverised coal (SCPC) plant. Simulations are performed using a combination of MATLAB and Aspen Plus v7.3. It was found that adding CAES to a SOFC-based plant can provide load-following capabilities with relatively small effects on efficiencies (1-2% HHV depending on the system configuration) and levelized costs of electricity (∼0.35 ¢ kW-1 h-1). The load-following capabilities, as measured by least-squares metrics, show that this system may utilize coal and achieve excellent load-tracking that is not adversely affected by the inclusion of CCS. Adding CCS to the SOFC/CAES system reduces measurable direct CO2 emission to zero. A seasonal partial plant shutdown schedule is found to reduce fuel consumption by 9.5% while allowing for cleaning and maintenance windows for the SOFC stacks without significantly affecting the performance of the system (∼1% HHV reduction in efficiency). The SOFC-based systems with CCS are found to become economically attractive relative to SCPC above carbon taxes of 22 ton-1.

  2. Impact of Improved Solar Forecasts on Bulk Power System Operations in ISO-NE (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Brancucci Martinez-Anido, C.; Florita, A.; Hodge, B.M.

    2014-11-01

    The diurnal nature of solar power is made uncertain by variable cloud cover and the influence of atmospheric conditions on irradiance scattering processes. Its forecasting has become increasingly important to the unit commitment and dispatch process for efficient scheduling of generators in power system operations. This presentation is an overview of a study that examines the value of improved solar forecasts on Bulk Power System Operations.

  3. Optimal Bidding and Operation of a Power Plant with Solvent-Based Carbon Capture under a CO2 Allowance Market: A Solution with a Reinforcement Learning-Based Sarsa Temporal-Difference Algorithm

    Directory of Open Access Journals (Sweden)

    Ziang Li

    2017-04-01

    Full Text Available In this paper, a reinforcement learning (RL-based Sarsa temporal-difference (TD algorithm is applied to search for a unified bidding and operation strategy for a coal-fired power plant with monoethanolamine (MEA-based post-combustion carbon capture under different carbon dioxide (CO2 allowance market conditions. The objective of the decision maker for the power plant is to maximize the discounted cumulative profit during the power plant lifetime. Two constraints are considered for the objective formulation. Firstly, the tradeoff between the energy-intensive carbon capture and the electricity generation should be made under presumed fixed fuel consumption. Secondly, the CO2 allowances purchased from the CO2 allowance market should be approximately equal to the quantity of CO2 emission from power generation. Three case studies are demonstrated thereafter. In the first case, we show the convergence of the Sarsa TD algorithm and find a deterministic optimal bidding and operation strategy. In the second case, compared with the independently designed operation and bidding strategies discussed in most of the relevant literature, the Sarsa TD-based unified bidding and operation strategy with time-varying flexible market-oriented CO2 capture levels is demonstrated to help the power plant decision maker gain a higher discounted cumulative profit. In the third case, a competitor operating another power plant identical to the preceding plant is considered under the same CO2 allowance market. The competitor also has carbon capture facilities but applies a different strategy to earn profits. The discounted cumulative profits of the two power plants are then compared, thus exhibiting the competitiveness of the power plant that is using the unified bidding and operation strategy explored by the Sarsa TD algorithm.

  4. Power training using pneumatic machines vs. plate-loaded machines to improve muscle power in older adults.

    Science.gov (United States)

    Balachandran, Anoop T; Gandia, Kristine; Jacobs, Kevin A; Streiner, David L; Eltoukhy, Moataz; Signorile, Joseph F

    2017-08-10

    Power training has been shown to be more effective than conventional resistance training for improving physical function in older adults; however, most trials have used pneumatic machines during training. Considering that the general public typically has access to plate-loaded machines, the effectiveness and safety of power training using plate-loaded machines compared to pneumatic machines is an important consideration. The purpose of this investigation was to compare the effects of high-velocity training using pneumatic machines (Pn) versus standard plate-loaded machines (PL). Independently-living older adults, 60years or older were randomized into two groups: pneumatic machine (Pn, n=19) and plate-loaded machine (PL, n=17). After 12weeks of high-velocity training twice per week, groups were analyzed using an intention-to-treat approach. Primary outcomes were lower body power measured using a linear transducer and upper body power using medicine ball throw. Secondary outcomes included lower and upper body muscle muscle strength, the Physical Performance Battery (PPB), gallon jug test, the timed up-and-go test, and self-reported function using the Patient Reported Outcomes Measurement Information System (PROMIS) and an online video questionnaire. Outcome assessors were blinded to group membership. Lower body power significantly improved in both groups (Pn: 19%, PL: 31%), with no significant difference between the groups (Cohen's d=0.4, 95% CI (-1.1, 0.3)). Upper body power significantly improved only in the PL group, but showed no significant difference between the groups (Pn: 3%, PL: 6%). For balance, there was a significant difference between the groups favoring the Pn group (d=0.7, 95% CI (0.1, 1.4)); however, there were no statistically significant differences between groups for PPB, gallon jug transfer, muscle muscle strength, timed up-and-go or self-reported function. No serious adverse events were reported in either of the groups. Pneumatic and plate

  5. Optimal placement of unified power flow controllers to improve dynamic voltage stability using power system variable based voltage stability indices.

    Science.gov (United States)

    Albatsh, Fadi M; Ahmad, Shameem; Mekhilef, Saad; Mokhlis, Hazlie; Hassan, M A

    2015-01-01

    This study examines a new approach to selecting the locations of unified power flow controllers (UPFCs) in power system networks based on a dynamic analysis of voltage stability. Power system voltage stability indices (VSIs) including the line stability index (LQP), the voltage collapse proximity indicator (VCPI), and the line stability index (Lmn) are employed to identify the most suitable locations in the system for UPFCs. In this study, the locations of the UPFCs are identified by dynamically varying the loads across all of the load buses to represent actual power system conditions. Simulations were conducted in a power system computer-aided design (PSCAD) software using the IEEE 14-bus and 39- bus benchmark power system models. The simulation results demonstrate the effectiveness of the proposed method. When the UPFCs are placed in the locations obtained with the new approach, the voltage stability improves. A comparison of the steady-state VSIs resulting from the UPFCs placed in the locations obtained with the new approach and with particle swarm optimization (PSO) and differential evolution (DE), which are static methods, is presented. In all cases, the UPFC locations given by the proposed approach result in better voltage stability than those obtained with the other approaches.

  6. Optimal placement of unified power flow controllers to improve dynamic voltage stability using power system variable based voltage stability indices.

    Directory of Open Access Journals (Sweden)

    Fadi M Albatsh

    Full Text Available This study examines a new approach to selecting the locations of unified power flow controllers (UPFCs in power system networks based on a dynamic analysis of voltage stability. Power system voltage stability indices (VSIs including the line stability index (LQP, the voltage collapse proximity indicator (VCPI, and the line stability index (Lmn are employed to identify the most suitable locations in the system for UPFCs. In this study, the locations of the UPFCs are identified by dynamically varying the loads across all of the load buses to represent actual power system conditions. Simulations were conducted in a power system computer-aided design (PSCAD software using the IEEE 14-bus and 39- bus benchmark power system models. The simulation results demonstrate the effectiveness of the proposed method. When the UPFCs are placed in the locations obtained with the new approach, the voltage stability improves. A comparison of the steady-state VSIs resulting from the UPFCs placed in the locations obtained with the new approach and with particle swarm optimization (PSO and differential evolution (DE, which are static methods, is presented. In all cases, the UPFC locations given by the proposed approach result in better voltage stability than those obtained with the other approaches.

  7. Optimal Placement of Unified Power Flow Controllers to Improve Dynamic Voltage Stability Using Power System Variable Based Voltage Stability Indices

    Science.gov (United States)

    Albatsh, Fadi M.; Ahmad, Shameem; Mekhilef, Saad; Mokhlis, Hazlie; Hassan, M. A.

    2015-01-01

    This study examines a new approach to selecting the locations of unified power flow controllers (UPFCs) in power system networks based on a dynamic analysis of voltage stability. Power system voltage stability indices (VSIs) including the line stability index (LQP), the voltage collapse proximity indicator (VCPI), and the line stability index (Lmn) are employed to identify the most suitable locations in the system for UPFCs. In this study, the locations of the UPFCs are identified by dynamically varying the loads across all of the load buses to represent actual power system conditions. Simulations were conducted in a power system computer-aided design (PSCAD) software using the IEEE 14-bus and 39- bus benchmark power system models. The simulation results demonstrate the effectiveness of the proposed method. When the UPFCs are placed in the locations obtained with the new approach, the voltage stability improves. A comparison of the steady-state VSIs resulting from the UPFCs placed in the locations obtained with the new approach and with particle swarm optimization (PSO) and differential evolution (DE), which are static methods, is presented. In all cases, the UPFC locations given by the proposed approach result in better voltage stability than those obtained with the other approaches. PMID:25874560

  8. Harnessing the Collective Power of Eyewitnesses for Improved Earthquake Information

    Science.gov (United States)

    Bossu, R.; Lefebvre, S.; Mazet-Roux, G.; Steed, R.

    2013-12-01

    The Euro-Med Seismological Centre (EMSC) operates the second global earthquake information website (www.emsc-csem.org) which attracts 2 million visits a month from about 200 different countries. We collect information about earthquakes' effects from eyewitnesses such as online questionnaires, geolocated pics to rapidly constrain impact scenario. At the beginning, the collection was purely intended to address a scientific issue: the rapid evaluation of earthquake's impact. However, it rapidly appears that the understanding of eyewitnesses' expectations and motivations in the immediate aftermath of an earthquake was essential to optimise this data collection. Crowdsourcing information on earthquake's effects does not apply to a pre-existing community. By definition, eyewitnesses only exist once the earthquake has struck. We developed a strategy on social networks (Facebook, Google+, Twitter...) to interface with spontaneously emerging online communities of eyewitnesses. The basic idea is to create a positive feedback loop: attract eyewitnesses and engage with them by providing expected earthquake information and services, collect their observations, collate them for improved earthquake information services to attract more witnesses. We will present recent examples to illustrate how important the use of social networks is to engage with eyewitnesses especially in regions of low seismic activity where people are unaware of existing Internet resources dealing with earthquakes. A second type of information collated in our information services is derived from the real time analysis of the traffic on our website in the first minutes following an earthquake occurrence, an approach named flashsourcing. We show, using the example of the Mineral, Virginia earthquake that the arrival times of eyewitnesses of our website follows the propagation of the generated seismic waves and then, that eyewitnesses can be considered as ground motion sensors. Flashsourcing discriminates felt

  9. Fractured tenure, unaccountable authority, and benefit capture: Constraints to improving community benefits under climate change mitigation schemes in Ghana

    Directory of Open Access Journals (Sweden)

    Emmanuel Marfo

    2012-01-01

    Full Text Available The debate on climate change and ecosystem services has grown substantially over the past two decades. The post-Kyoto protocol period particularly has witnessed increased formulation of financial mechanisms to compensate for green efforts towards carbon sequestration and reduction in deforestation. In most cases, communities substantially depend on forests for their livelihoods or their actions have a direct bearing on the sustainability of the forests. Will the economic incentives from emerging initiatives offer new sources of income to support rural livelihoods and reduce poverty? There is some doubt about this potential, because there is enormous evidence across the world to show that forest exploitation and use has not substantially benefited local people and Ghana is no exception. This paper draws on existing evidence in Ghana to show that the lack of secure community tenure rights and the dominance of unaccountable authority-which leads to benefit capture by local elites-are critical constraints to equitable forest benefit sharing. Building on the evidence, this paper argues that unless these issues are addressed in policy and practice, the potential economic benefits from the various emerging mechanisms under climate change and ecosystem services may not benefit local people; they may even reinforce the gap between the rich and the poor.

  10. STATIC CONVERTERS OF THE ELECTRIC POWER WITH IMPROVED OPERATION-TECHNICAL CHARACTERISTICS

    Directory of Open Access Journals (Sweden)

    Uskov A. E.

    2014-03-01

    Full Text Available The article describes scopes and new technical decisions of static converters of the electric power with the improved operation-characteristics, executed with use of new element base and a modular principle of construction

  11. Transient Stability Improvement of IEEE 9 Bus System Using Power World Simulator

    Directory of Open Access Journals (Sweden)

    Kaur Ramandeep

    2016-01-01

    Full Text Available The improvement of transient stability of power system was one of the most challenging research areas in power engineer.The main aim of this paper was transient stability analysis and improvement of IEEE 9 bus system. These studies were computed using POWER WORLD SIMULATOR. The IEEE 9 bus system was modelled in power world simulator and load flow studies were performed to determine pre-fault conditions in the system using Newton-Raphson method. The transient stability analysis was carried out using Runga method during three-phase balanced fault. For the improvement transient stability, the general methods adopted were fast acting exciters, FACT devices and addition of parallel transmission line. These techniques play an important role in improving the transient stability, increasing transmission capacity and damping low frequency oscillations.

  12. Improving the Reliability of LDP through the Divergence of Power Supply for LDP

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Bang Sil [KHNP CRI, Daejeon (Korea, Republic of)

    2016-10-15

    The representative operating systems are Large Display Panel (LDP), Operator Workstation (OWS), Computerized Procedure System (CPS). The LDP provides the information which is plant essential safety function, plant operating mode, the state of major operating variable and the important alarm to operator continuously. In case of malfunction and switchover fail of the inverter, it is possible to occur the power loss of LDP. The power of LDP and operator console workstation had been supplied by only 2 non-safety Power Line1/Power Line2 (P.L1/P.L2). This study mentioned the divergence of power for LDP as method of power loss caused by unreliability of inverter. Ultimately, LDP power line has been added, and then it is more improved on the safety of LDP operation than before. So Shin-Kori 3,4 can enhance the reliability and economic, safety of plant.

  13. Improving human reliability through better nuclear power plant system design: Program for advanced nuclear power studies. Progress report

    Energy Technology Data Exchange (ETDEWEB)

    Golay, M.W.

    1993-10-10

    The project on ``Development of a Theory of the Dependence of Human Reliability upon System Designs as a Means of Improving Nuclear Power Plant Performance`` was been undertaken in order to address the problem of human error in advanced nuclear power plant designs. Lack of a mature theory has retarded progress in reducing likely frequencies of human errors. Work being pursued in this project is to perform a set of experiments involving human subjects who are required to operate, diagnose and respond to changes in computer-simulated systems, relevant to those encountered in nuclear power plants, which are made to differ in complexity in a systematic manner. The computer program used to present the problems to be solved also records the response of the operator as it unfolds.

  14. A High-Voltage class-D power amplifier with switching frequency regulation for improved high-efficiency output power range

    NARCIS (Netherlands)

    Ma, Haifeng; Zee, van der Ronan; Nauta, Bram

    2015-01-01

    This paper describes the power dissipation analysis and the design of an efficiency-improved high-voltage class-D power amplifier. The amplifier adaptively regulates its switching frequency for optimal power efficiency across the full output power range. This is based on detecting the switching outp

  15. Investigation of Energy Storage Devices Impact on Improvement of Power Quality Aspects

    Directory of Open Access Journals (Sweden)

    S. Torabzad

    2012-03-01

    Full Text Available Energy production and storage are in the midst of some major changes. During the past decade, energy production and storage have become a high priority for business and government because of concerns relating to the environment and sustainability of energy sources. The power quality problems that have occurred on the existing, aging system will continue to worsen as intermittent, renewable energy systems are added. Fastacting energy storage is required to help combat this problem. Among the many FACTS devices which can improve the power system operation and power quality problems, Static Compensator (STATCOM and Unified Power Flow Controller (UPFC are of the most promising new FACTS technologies. Both of these devices utilize capacitors as the dc bus. Since capacitors are passive elements with very limited energy storage, they cannot provide controllable real power for extended period. This paper investigates the impact of integrating a Battery Energy Storage System (BESS and/or a Superconducting Magnetic Energy Storage (SMES across the dc bus of STATCOM. This will allow fast control of both real and reactive power to improve power system transient stability and to provide extra damping against power system oscillation in a multi-area system linked by weak inter-connection. Comparative dynamic performances of these devices are presented in this study. A control strategy is proposed to integrate these devices to improve the active power management within the constraints of the power system to which the device is connected. The proposed controller based on hysterisis control ensures unity power factor and sinusoidal supply current irrespective of the variation in the load demand waveform and magnitude. Results from simulation studies using realistic model of the power electronic devices on the dynamic performance of these schemes will be presented.

  16. Power System Transient Stability Improvement Using Demand Side Management in Competitive Electricity Markets

    DEFF Research Database (Denmark)

    Hu, Weihao; Wang, Chunqi; Chen, Zhe

    2012-01-01

    Since the hourly spot market price is available one day ahead in Denmark, the price could be transferred to the consumers and they may shift some of their loads from high price periods to the low price periods in order to save their energy costs. The optimal load response to an electricity price...... for demand side management generates different load profiles and may provide an opportunity to improve the transient stability of power systems with high wind power penetrations. In this paper, the idea of the power system transient stability improvement by using optimal load response to the electricity...

  17. Application of the direct Lyapunov method to improve damping of power swings by control of UPFC

    Energy Technology Data Exchange (ETDEWEB)

    Januszewski, M.; Machowski, J. [Warsaw Univ. of Technology (Poland). Inst. of Elektroenergetyki; Bialek, J.W. [Edinburgh Univ. (United Kingdom). School of Engineering and Electronics

    2004-03-01

    Large interconnected power systems often suffer from weakly damped swings between synchronous generators and subsystems. This paper presents an approach, based on the use of the nonlinear system model and application of the direct Lyapunov method, to improve damping of power swings using the unified power flow controller (UPFC). A state-variable control strategy has been derived as well as its implementation using locally available signals of real and reactive power. The results of simulation tests, undertaken using a small multi-machine system model, have been presented. (author)

  18. Small Signal Stability Improvement of Power Systems Using Optimal Load Responses in Competitive Electricity Markets

    DEFF Research Database (Denmark)

    Hu, Weihao; Su, Chi; Chen, Zhe;

    2011-01-01

    Since the hourly spot market price is available one day ahead in Denmark, the price could be transferred to the consumers and they may shift some of their loads from high price periods to the low price periods in order to save their energy costs. The optimal load response to an electricity price...... price is proposed. A 17-bus power system with high wind power penetrations, which resembles the Eastern Danish power system, is chosen as the study case. Simulation results show that the optimal load response to electricity prices is an effective measure to improve the small signal stability of power...

  19. Z-Source-Inverter-Based Flexible Distributed Generation System Solution for Grid Power Quality Improvement

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Vilathgamuwa, D. M.; Loh, Poh Chiang

    2009-01-01

    Distributed generation (DG) systems are usually connected to the grid using power electronic converters. Power delivered from such DG sources depends on factors like energy availability and load demand. The converters used in power conversion do not operate with their full capacity all the time......-stage buck-boost inverter, recently proposed Z-source inverter (ZSI) is a good candidate for future DG systems. This paper presents a controller design for a ZSI-based DG system to improve power quality of distribution systems. The proposed control method is tested with simulation results obtained using...

  20. Study of UPFC Optimal Location Considering Loss Reduction and Improvement of Voltage Stability and Power Flow

    Directory of Open Access Journals (Sweden)

    Islam Youcef DJILANI KOBIBI

    2014-02-01

    Full Text Available With the increase in power demand, operation and planning of large interconnected power system are becoming more complex, so power system will become less secure and stable. A new concept of Flexible AC Transmission system (FACTS brought radical changes in the power system operation and control. FACTS controllers narrow the gap between the no controlled and the controlled power system mode of operation, by providing additional degrees of freedom to control power flows and voltages. Unified Power Flow Controller (UPFC is a versatile FACTS device which can independently or simultaneously control the active power, the reactive power, and the bus voltage to which it is connected. The main purpose of this paper is to identify the optimal location of the Unified Power Flow Controller (UPFC in order to minimize active power losses and improve the voltage profiles using the injection model of the (UPFC in Newton-Raphson load flow algorithm, in an IEEE- 14, 30, 57, 118, 300 Bus test systems.

  1. Inter-Area Power Systems Stability Improvement by Static Synchronous Series Compensator

    Directory of Open Access Journals (Sweden)

    Prechanon Kumkratug

    2011-01-01

    Full Text Available Problem statement: The inter-area power systems have special characteristic of the stability behavior. The improvement of inter-area power system is one of the important aspects in power system. Approach: This study applies the Static Synchronous Series Compensator (SSSC to improve stability of inter-area systems. The SSSC is modeled and then is applied to be incorporated into the power system model for investigating stability improvement. The SSSC is modeled as the variable susceptance and is controlled during dynamic state. This presented SSSC model can be incorporated into susceptance matrix of power system model. The presented method is tested on sample inter-area power system with 3 phase fault distubrances. Results: The swing curve of inter-area power system without a SSSC gets increases monotonically and thus the system can be considered as unstable whereas the swing curves of system with a SSSC can be considered as stable. Conclusion: From the simulation results, the SSSC can enhance stability of inter-area power systems.

  2. Improved low-power semiconductor diode lasers for photodynamic therapy in veterinary medicine

    Science.gov (United States)

    Lee, Susanne M.; Mueller, Eduard K.; Van de Workeen, Brian C.; Mueller, Otward M.

    2001-05-01

    Cryogenically cooling semiconductor diode lasers provides higher power output, longer device lifetime, and greater monochromaticity. While these effects are well known, such improvements have not been quantified, and thus cryogenically operated semiconductor lasers have not been utilized in photodynamic therapy (PDT). We report quantification of these results from laser power meter and photospectrometer data. The emission wavelengths of these low power multiple quantum well semiconductor lasers were found to decrease and become more monochromatic with decreasing temperature. Significant power output improvements also were obtained at cryogenic temperatures. In addition, the threshold current, i.e. the current at which lasing begins, decreased with decreasing temperature. This lower threshold current combined with the increased power output produced dramatically higher device efficiencies. It is proposed that cryogenic operation of semiconductor diode lasers will reduce the number of devices needed to produce the requisite output for many veterinary and medical applications, permitting significant cost reductions.

  3. Research on improvement of power quality of Micro - grid based on SVG pulse load

    Science.gov (United States)

    Lv, Chuang; Xie, Pu

    2017-05-01

    Pulse load will make the micro-grid public bus power to produce a high peak pulse due to its cyclical pulsation characteristics,, and make the micro-grid voltage fluctuations, frequency fluctuations, voltage and current distortion, power factor reduction and other adverse effects. In order to suppress the adverse effects of the pulse load on the microgrid and improve the power quality of the microgrid, this paper established the SVG simulation model in Matlab / Simulink environment, the superiority of SVG is verified by comparing the improvement of power quality before and after adding the SVG to microgrid system. The results show that the SVG model can suppress the adverse effects effectively of the pulse load on the microgrid, which is of great value and significance to the reactive power compensation and harmonic suppression of the microgrid.

  4. Improving uncertainty evaluation of process models by using pedigree analysis. A case study on CO2 capture with monoethanolamine

    NARCIS (Netherlands)

    van der Spek, Mijndert; Ramirez, Andrea|info:eu-repo/dai/nl/284852414; Faaij, André

    2016-01-01

    This article aims to improve uncertainty evaluation of process models by combining a quantitative uncertainty evaluation method (data validation) with a qualitative uncertainty evaluation method (pedigree analysis). The approach is tested on a case study of monoethanolamine based postcombustion CO2

  5. 3-D Micro and Nano Technologies for Improvements in Electrochemical Power Devices

    Directory of Open Access Journals (Sweden)

    Sunshine Holmberg

    2014-04-01

    Full Text Available This review focuses on recent advances in micro- and nano-fabrication techniques and their applications to electrochemical power devices, specifically microfabricated Lithium-ion batteries, enzymatic and microbial fuel cells (biofuel cells, and dye-sensitized solar cells (DSSCs. Although the maturity of these three technologies ranges from market ready (batteries to fundamental research (biofuel cells to applied research (DSSCs, advances in MEMS (Micro-Electro-Mechanical Systems and NEMS (Nano-Electro-Mechanical Systems techniques, particularly modifications in surface area and surface chemistry, and novel genetic and molecular engineering techniques, significantly improve the electrochemical activity of these technologies across the board. For each of these three categories of power-MEMS devices the review covers: (1 The technical challenges facing the performance and fabrication of electrochemical power devices; (2 Current MEMS and NEMS techniques used to improve efficiency; and (3 Future outlook and suggested improvements of MEMS and NEMS for implementation in electrochemical power devices.

  6. A GPS-Based Control Framework for Accurate Current Sharing and Power Quality Improvement in Microgrids

    DEFF Research Database (Denmark)

    Golsorkhi, Mohammad; Savaghebi, Mehdi; Lu, Dylan;

    2016-01-01

    consensus protocol to ensure proportional sharing of average power. The voltage conditioning scheme produces compensation signals at fundamental and dominant harmonics to improve the voltage quality at a sensitive load bus. Experimental results are presented to validate the efficacy of the proposed method.......This paper proposes a novel hierarchical control strategy for improvement of load sharing and power quality in ac microgrids. This control framework is composed of a droop based controller at the primary level, and a combination of distributed power sharing and voltage conditioning schemes...... dynamic response. The droop coefficient, which acts as a virtual resistance is adaptively changed as a function of the peak current. This strategy not only simplifies the control design but also improves the current sharing accuracy at high loading conditions. The distributed power sharing scheme uses...

  7. Capturing appearance

    Science.gov (United States)

    Rushmeier, Holly E.

    2005-01-01

    For computer graphics applications, capturing the appearance parameters of objects (reflectance, transmittance and small scale surface structures), is as important as capturing the overall shape. We briefly review recent approaches developed by the computer graphics community to solve this problem. Excellent results have been obtained by various researchers measuring spatially varying reflectance functions for some classes of objects. We will consider some challenges from two of the remaining problematic classes of objects. First we will describe our experience scanning and modeling the throne of Tutankhamen. The major difficulties in this case were that the base shape was a highly detailed non-convex geometry with complex topology, and the shape was covered by optically uncooperative gold and silver. Then we will discuss some observations from our ongoing project to scan and model historic buildings on the Yale campus. The major difficulties in this second case are quantity of data and the lack of control over acquisition conditions.

  8. 油田燃煤电厂CO2捕集纯化工程实践%CO2 capture and purification in coal-fired power plant

    Institute of Scientific and Technical Information of China (English)

    马玉峰; 郝杰; 万志鹏; 张翠红

    2014-01-01

    CO2是一种温室气体,通过CO2收集、驱油技术,能将造成温室效应的气体用于提高原油采收率,同时减少工业生产中温室气体的排放。为了实现CO2的捕集纯化,胜利油田采用一乙醇胺溶液( MEA)化学吸收工艺捕集CO2。介绍了“低渗透油藏CO2驱油”重大先导试验,在胜利发电厂建设CO2捕集纯化装置,通过此装置收集稳定、廉价的CO2气体用于驱油生产实践。通过分析系统运行状况,对装置进行了一系列的试验、研究,总结了大量CO2捕集系统的工程应用经验。胜利油田CO2捕集项目,通过将大型燃煤电厂烟道气中CO2捕集纯化、安全输送等系列技术攻关,形成低能耗捕集纯化、运输的集成配套技术。%CO2,known as a greenhouse gas,is recycled to improve the production of crude oil through collection an d oil-driving technolo-gies.Shengli Oilfield adopts MEA chemical adsorption process to capture and purify CO2.To develop low permeability reservoir,conduct CO2 flooding experiment.First,build capture and purification devices which capture and purify the CO2 from the large-scale coal-fired power plant.Analyze the matched CO2 conveying techniques.The actual operation experiment guides the subsequent object design.

  9. A Review of Distributed Control Techniques for Power Quality Improvement in Micro-grids

    Science.gov (United States)

    Zeeshan, Hafiz Muhammad Ali; Nisar, Fatima; Hassan, Ahmad

    2017-05-01

    Micro-grid is typically visualized as a small scale local power supply network dependent on distributed energy resources (DERs) that can operate simultaneously with grid as well as in standalone manner. The distributed generator of a micro-grid system is usually a converter-inverter type topology acting as a non-linear load, and injecting harmonics into the distribution feeder. Hence, the negative effects on power quality by the usage of distributed generation sources and components are clearly witnessed. In this paper, a review of distributed control approaches for power quality improvement is presented which encompasses harmonic compensation, loss mitigation and optimum power sharing in multi-source-load distributed power network. The decentralized subsystems for harmonic compensation and active-reactive power sharing accuracy have been analysed in detail. Results have been validated to be consistent with IEEE standards.

  10. Probabilistic power flow using improved Monte Carlo simulation method with correlated wind sources

    Science.gov (United States)

    Bie, Pei; Zhang, Buhan; Li, Hang; Deng, Weisi; Wu, Jiasi

    2017-01-01

    Probabilistic Power Flow (PPF) is a very useful tool for power system steady-state analysis. However, the correlation among different random injection power (like wind power) brings great difficulties to calculate PPF. Monte Carlo simulation (MCS) and analytical methods are two commonly used methods to solve PPF. MCS has high accuracy but is very time consuming. Analytical method like cumulants method (CM) has high computing efficiency but the cumulants calculating is not convenient when wind power output does not obey any typical distribution, especially when correlated wind sources are considered. In this paper, an Improved Monte Carlo simulation method (IMCS) is proposed. The joint empirical distribution is applied to model different wind power output. This method combines the advantages of both MCS and analytical method. It not only has high computing efficiency, but also can provide solutions with enough accuracy, which is very suitable for on-line analysis.

  11. DG Placement with Considering Reliability Improvement and Power Loss Reduction with GA Method

    Directory of Open Access Journals (Sweden)

    Mohammad Mohammadi

    2011-08-01

    Full Text Available Distributed generators are beneficial in reducing the losses effectively compared to other methods of loss reduction. DGs can be implemented for improvement of reliability of system; too In this study optimal DG unit placement using GA is discussed. The optimal size of the DG unit is calculated analytically using approximate reasoning suitable nodes are determined for DG unit placement. Reliability and power loss reduction indices of distribution system nodes are modeled. GA containing a set of rules is used to determine the DG unit placement. DG units are placed with the highest suitability index. Simulation results show the advantage of optimal DG unit placement. Compared to other power loss and reliability improvement techniques, placement it is giving very good reduction not only in power loss but also it is improving reliability improvement.

  12. 中国风电和碳捕集技术发展路径与减排成本研究——基于技术学习曲线的分析%Toward Characteristics of Development of Wind Power and Carbon Capture Technology in China Based on Technological Learning Curves

    Institute of Scientific and Technical Information of China (English)

    黄建

    2012-01-01

    Coal has been the major energy source in China.The proportion of coal utilization for power generation will even become higher.The key of China’s low-carbon development lies in the choice of low-carbon power technology and its popularization.Compared with hydropower and nuclear power,development of wind power and carbon capture technology is still at preliminary stages.The overall objective of this study was to discuss characteristics of main problems in wind power and carbon capture technology,including the time of deployment,potential of CO2 emission reductions,as well as costs of CO2 emission reductions based on their learning curves.This would be greatly helpful in providing a scientific basis of decision-makers.First,differences in deployment of low-carbon energy technologies of China and the world were compared and contrast.Due to the rapid development of economy and rapid growth of energy demand,the China’s energy deployment rate is much higher than the world average.Based on it,China’s deployment rate was combined with the technological learning curve to analyze the deployment path of wind power and carbon capture technologies.Conclusions were drawn as follows.1)The CO2 mitigation cost of wind power is marginally higher than the carbon capture technology,but when carbon transport cost and carbon storage cost are accounted for,the total cost of carbon capture technology is higher than the wind power;2)The total added investment of wind power is slightly higher than that of the newly built pulverized coal power plant with carbon capture.The investment(including the construction investment)of wind power is 71.9%of the total added investment,which means that improvement in the learning rate will largely reduce the total added investment.The total added investments for carbon capture technology are lower,almost all of which are from the fuel cost and total added investments of the capital of the pulverized coal plant with carbon capture;3

  13. A Study on Nonconformance and Construction Method Improvement for Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Yeob; Roh, Myung Sub [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

    2014-10-15

    Advanced power reactor was developed by domestic technology, and finally exported to abroad. In order to place the current nuclear power industrial base, construction has played a big role. Without magnificent construction technology, it would have been impossible to get a safe nuclear power plant on time and in budget. Construction industry occupies very large portion of the economy in South Korea and it has been a core of South Korea's economic growth. With a competitive construction industry and advanced nuclear power plant construction know-how, South Korea could provide safe and reliable nuclear power plants in domestic and world. However there are many repairs and number of corrective actions are in actual construction. Thus, this paper suggested the result of nonconformance and construction method improvement for nuclear power plant. Constructional engineering is a kind of science that has a variety of disciplines including structure, geology, mechanical equipment and other fields. Thus, the development of constructional engineering is closely associated with experience from failure and application advanced construction method. The recent experience in nuclear power plants construction has shown that those improved methods are fully applicable and can help shorten the construction schedule. The future of nuclear power plant construction seems to be more encouraged, even though it has many obstacles.

  14. Power swings damping improvement by UPFC and SMES integration based on direct Lyapunov method control

    Energy Technology Data Exchange (ETDEWEB)

    Bidadfar, A.; Abedi, M.; Chu, C.C. [Tafresh Univ., Tafresh (Iran, Islamic Republic of). Dept. of Electrical Engineering; AmirKabir Univ., Tehran (Iran, Islamic Republic of). Dept. of Electrical Engineering

    2010-07-01

    An improved method of damping power swings in power systems was presented. In addition to integrating the unified power flow controller (UPFC) and superconducting magnetic energy storage (SMES), the approach also applied the direct Lyapunov method concept to determine the control scheme based on nonlinear power system model. In transient state, SMES cooperates with the UPFC converters in active power exchange. The UPFC current injection model enables the control of UPFC converters using the Lyapunov direct method. Power oscillations among power system generators decrease as a result of the energy exchanging capability of the SMES. The steady state control method is obtained to fulfill the normal task of the UPFC in the presence of SMES. The decentralizing method is used to locally control the UPFC-SMES independent of state variables of synchronous generators which require wide area measurements. PSCAD/EMTDC simulation of a typical multi-area system revealed that in addition to an improvement in power swing damping, there was a pronounced decrease of the first swing.

  15. A theranostic approach based on the use of a dual boron/Gd agent to improve the efficacy of Boron Neutron Capture Therapy in the lung cancer treatment.

    Science.gov (United States)

    Alberti, Diego; Protti, Nicoletta; Toppino, Antonio; Deagostino, Annamaria; Lanzardo, Stefania; Bortolussi, Silva; Altieri, Saverio; Voena, Claudia; Chiarle, Roberto; Geninatti Crich, Simonetta; Aime, Silvio

    2015-04-01

    This study aims at developing an innovative theranostic approach for lung tumor and metastases treatment, based on Boron Neutron Capture Therapy (BNCT). It relies on to the use of low density lipoproteins (LDL) as carriers able to maximize the selective uptake of boron atoms in tumor cells and, at the same time, to quantify the in vivo boron distribution by magnetic resonance imaging (MRI). Tumor cells uptake was initially assessed by ICP-MS and MRI on four types of tumor (TUBO, B16-F10, MCF-7, A549) and one healthy (N-MUG) cell lines. Lung metastases were generated by intravenous injection of a Her2+ breast cancer cell line (i.e. TUBO) in BALB/c mice and transgenic EML4-ALK mice were used as primary tumor model. After neutron irradiation, tumor growth was followed for 30-40 days by MRI. Tumor masses of boron treated mice increased markedly slowly than the control group. From the clinical editor: In this article, the authors described an improvement to existing boron neutron capture therapy. The dual MRI/BNCT agent, carried by LDLs, was able to maximize the selective uptake of boron in tumor cells, and, at the same time, quantify boron distribution in tumor and in other tissues using MRI. Subsequent in vitro and in vivo experiments showed tumor cell killing after neutron irradiation. Copyright © 2015 Elsevier Inc. All rights reserved.

  16. TrapTech R-Octenol Lure Does Not Improve the Capture Rates of Aedes albopictus (Diptera: Culicidae) and Other Container-Inhabiting Species in Biogents Sentinel Traps.

    Science.gov (United States)

    Unlu, Isik; Faraji, Ary; Indelicato, Nicholas; Rochlin, Ilia

    2016-07-01

    Aedes albopictus (Skuse) and other container-inhabiting species have become important public health concerns due to the transmission of dengue, chikungunya, and Zika viruses. Effective surveillance is dependent on the ability to collect a sufficient number of mosquitoes for population monitoring and pathogen isolation. The Biogents Sentinel (BGS) trap supplied with a proprietary human skin lure has become the standard tool for container-inhabiting Aedes species collections worldwide. Recently, R-octenol, a single isomer of the well characterized mosquito attractant octenol, was shown to greatly improve the capture rate of some Aedes species when utilized with the Center for Disease Control and Prevention (CDC) light traps and Mosquito Magnet traps. This study evaluated the effectiveness of the TrapTech lure (TT lure), containing R-octenol, alone or in combination with the human skin lure in a BGS trap to capture Ae. albopictus and other species. BGS traps with human skin lures or a combination of the two lures collected approximately twice as many Ae. albopictus females compared to those with TT lures. Unlike previous studies, baiting BGS traps with TT lures did not result in increased diversity of mosquito species, or in higher numbers of other container-inhabiting Aedes species. Although human skin lures were clearly superior to TT R-octenol lures in BGS traps, R-octenol lures are more widely available and might still be used as an alternative lure, especially when Ae. albopictus populations are high.

  17. Comparison of Carbon Dioxide Capture Technology in Power Plant%电厂二氧化碳捕捉技术对比研究

    Institute of Scientific and Technical Information of China (English)

    王泽平; 周涛; 张记刚; 李洋

    2011-01-01

    由于全球温室效应的不断加剧,发展二氧化碳捕捉技术变得十分必要.通过分析燃烧前捕捉、燃烧后捕捉和富氧燃烧捕捉三种二氧化碳捕捉方式流程及其特点,指出三种不同的二氧化碳捕捉技术的发展现状以及应用途径.通过具体对比现有二氧化碳捕捉技术的工作原理以及优缺点,针对现有的几种具体的二氧化碳捕捉技术进行详细的分析,积极应用各种物理、化学、甚至生物的吸附技术,深入研究各种吸附技术的机理,寻找更高效的吸附方法,提高CO2的捕捉效率,减少捕捉成本.通过分析研究,提出以国家项目的形式立项,积极开展“燃烧前捕捉、燃烧后捕捉、寓氧燃烧捕捉”三种方式在中国的实验研究,尝试进行“燃烧中捕捉”研究,积极开创符合中国特色的二氧化碳捕捉技术的建议.%Due to increasingly intensified global greenhouse effect, it is quite necessary to develop carbon dioxide capture technology. By analysis of working process and characteristics of three different carbon dioxide capture technologies including pre-combustion capture, post-combustion capture and oxygen-enriched combustion technology, the current development and application of carbon dioxide capture technology were introduced. Different carbon dioxide capture technologies were discussed, with comparison of basic principle of technologies as well as their advantages and disadvantages. By detailed analysis of carbon dioxide capture technology, combining with analysis of basic principle and application of various physical, chemical, biological adsorption technology, more efficient adsorption methods were assessed in order to enhance CO2 capture efficiency and reduce capture cost. National level project and pilot study was proposed for the study of precombustion capture, postcombustion capture and oxygen enriched combustion technology. Technical development of carbon dioxide capture suitable to local

  18. Modeling and Simulation of a Novel Switched Reluctance Motor Drive System with Power Factor Improvement

    Directory of Open Access Journals (Sweden)

    G. Venkatesan

    2006-01-01

    Full Text Available This study presents a novel Switched Reluctance Motor (SRM drive system with power factor improvement. Recently, many of the converters with variable speed drives have no input power factor correction circuits. This results in harmonic pollution of the utility supply, which should be avoided. The effect of power factor variation in terms of harmonic content is also analyzed in this study. The different operations like single pulse, soft chopping and hard chopping modes are done with and without a power factor controller. This study describes the buck - boost converter topology with above said methods for SRM drive. The boost converter is used to improve the input sinusoidal current and the buck converter is used to regulate the dc source voltage. The proposed topologies were simulated using MATLAB / Simulink software package and the results were obtained. The computer simulation results support the proposed methods.

  19. An improved implicit multiple model predictive control used for movable nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Tai Yun, E-mail: nalren@stu.xjtu.edu.c [School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an Shaanxi, 710049 (China); Hou Suxia, E-mail: hsxhjj@sina.com.c [School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an Shaanxi, 710049 (China); Li Chong, E-mail: abcdirxj@stu.xjtu.edu.c [School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an Shaanxi, 710049 (China); Zhao Fuyu, E-mail: fyzhao@mail.xjtu.edu.c [School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an Shaanxi, 710049 (China)

    2010-10-15

    Compared with the nuclear power station, the movable nuclear plant has the special requirement of the load following ability and is more difficult to control. In this work, a MMPC (multiple model predictive control) method is applied to the power system of the movable nuclear plant. The linear models used to describe the power changing process, according to which the local controllers are designed, still suffer rough switching. In this paper, work has been done on the improvement of MMPC to make it better in application to the power system of the movable nuclear plant. The simulation results show that these modifications are available to improve the system's dynamic characters, and the multiple strategy is efficacious to solve the control problem of the parameter time-variable nonlinear system.

  20. Distributed generation system with PEM fuel cell for electrical power quality improvement

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez, D.; Beites, L.F.; Blazquez, F. [Department of Electrical Engineering, ETSII, Escuela de Ingenieros Industriales, Universidad Politecnica de Madrid, C/ Jose Gutierrez Abascal 2, 28006 Madrid (Spain); Ballesteros, J.C. [Endesa Generacion, S.A. c/ Ribera de Loira 60, 28042 Madrid (Spain)

    2008-08-15

    In this paper, a physical model for a distributed generation (DG) system with power quality improvement capability is presented. The generating system consists of a 5 kW PEM fuel cell, a natural gas reformer, hydrogen storage bottles and a bank of ultra-capacitors. Additional power quality functions are implemented with a vector-controlled electronic converter for regulating the injected power. The capabilities of the system were experimentally tested on a scaled electrical network. It is composed of different lines, built with linear inductances and resistances, and taking into account both linear and non-linear loads. The ability to improve power quality was tested by means of different voltage and frequency perturbations produced on the physical model electrical network. (author)

  1. The Distribution Network Reconfiguration Improved Performance of Genetic Algorithm Considering Power Losses and Voltage Profile

    Directory of Open Access Journals (Sweden)

    N. H. Shamsudin

    2014-05-01

    Full Text Available Power losses issues persevered over few decades in the high demand utilization of energy electricity in developing countries. Thus, the radial structure of distribution network configuration is extensively used in high populated areas to ensure continuity of power supply in the event of fault. This paper proposes heuristic Genetic Algorithm known as SIGA (Selection Improvement in Genetic Algorithm in consideration of genetic operator probabilities likewise the progression of switch adjustment in Distribution Network Reconfiguration (DNR while satisfying the parameters constraints. The SIGA algorithm was embodied throughout the process in IEEE 33-bus distribution system in selection of five tie switches. As a consequence, the power losses were ranked in accordance to the minimum values and voltage profile improvement obtainable by the proposed algorithm. The results show that the SIGA performs better than GA by giving the minimized value of power losses.

  2. Opposition-Based Improved PSO for Optimal Reactive Power Dispatch and Voltage Control

    Directory of Open Access Journals (Sweden)

    Shengrang Cao

    2015-01-01

    Full Text Available An opposition-based improved particle swarm optimization algorithm (OIPSO is presented for solving multiobjective reactive power optimization problem. OIPSO uses the opposition learning to improve search efficiency, adopts inertia weight factors to balance global and local exploration, and takes crossover and mutation and neighborhood model strategy to enhance population diversity. Then, a new multiobjective model is built, which includes system network loss, voltage dissatisfaction, and switching operation. Based on the market cost prices, objective functions are converted to least-cost model. In modeling process, switching operation cost is described according to the life cycle cost of transformer, and voltage dissatisfaction penalty is developed considering different voltage quality requirements of customers. The experiment is done on the new mathematical model. Through the simulation of IEEE 30-, 118-bus power systems, the results prove that OIPSO is more efficient to solve reactive power optimization problems and the model is more accurate to reflect the real power system operation.

  3. Capture of water-borne colloids in granular beds using external electric fields: improving removal of Cryptosporidium parvum.

    Science.gov (United States)

    Kulkarni, Pramod; Dutari, Gabriel; Weingeist, David; Adin, Avner; Haught, Roy; Biswas, Pratim

    2005-03-01

    Suboptimal coagulation in water treatment plants often results in reduced removal efficiency of Cryptosporidium parvum oocysts by several orders of magnitude (J. AWWA 94(6) (2002) 97, J. AWWA 93(12) (2001) 64). The effect of external electric field on removal of C. parvum oocysts in packed granular beds was studied experimentally. A cylindrical configuration of electrodes, with granular media in the annular space was used. A negative DC potential was applied to the central electrode. No coagulants or flocculants were used and filtration was performed with and without application of an electric field to obtain improvement in removal efficiency. Results indicate that removal of C. parvum increased from 10% to 70% due to application of field in fine sand media and from 30% to 96% in MAGCHEM media. All other test particles (Kaolin and polystyrene latex microspheres) used in the study also exhibited increased removal in the presence of an electric field. Single collector efficiencies were also computed using approximate trajectory analysis, modified to account for the applied external electric field. The results of these calculations were used to qualitatively explain the trends in the experimental observations.

  4. Altering Anode Thickness To Improve Power Production in Microbial Fuel Cells with Different Electrode Distances

    KAUST Repository

    Ahn, Yongtae

    2013-01-17

    A better understanding of how anode and separator physical properties affect power production is needed to improve energy and power production by microbial fuel cells (MFCs). Oxygen crossover from the cathode can limit power production by bacteria on the anode when using closely spaced electrodes [separator electrode assembly (SEA)]. Thick graphite fiber brush anodes, as opposed to thin carbon cloth, and separators have previously been examined as methods to reduce the impact of oxygen crossover on power generation. We examined here whether the thickness of the anode could be an important factor in reducing the effect of oxygen crossover on power production, because bacteria deep in the electrode could better maintain anaerobic conditions. Carbon felt anodes with three different thicknesses were examined to see the effects of thicker anodes in two configurations: widely spaced electrodes and SEA. Power increased with anode thickness, with maximum power densities (604 mW/m 2, 0.32 cm; 764 mW/m2, 0.64 cm; and 1048 mW/m2, 1.27 cm), when widely spaced electrodes (4 cm) were used, where oxygen crossover does not affect power generation. Performance improved slightly using thicker anodes in the SEA configuration, but power was lower (maximum of 689 mW/m2) than with widely spaced electrodes, despite a reduction in ohmic resistance to 10 Ω (SEA) from 51-62 Ω (widely spaced electrodes). These results show that thicker anodes can work better than thinner anodes but only when the anodes are not adversely affected by proximity to the cathode. This suggests that reducing oxygen crossover and improving SEA MFC performance will require better separators. © 2012 American Chemical Society.

  5. Improved methods for the generation of 24.5 keV neutron beams with possible application to boron neutron capture therapy

    Science.gov (United States)

    Constantine, G.; Baker, L. J.; Taylor, N. P.

    1986-09-01

    The production of epithermal neutron beams, filtered to provide a spectrum in which a small energy range predominates, is of importance for radiobiological research and in the development and calibration of instruments for monitoring intermediate energy neutrons. The penetration characteristics of intermediate energy neutrons in tissue lead to the possibility of application in the field of neutron capture therapy if beams of sufficient intensity and adequate spectral properties can be generated. In this paper methods of utilising the 24.5 keV antiresonance in the iron neutron cross section are described, and the DENIS (depth enhanced neutron intense source) principle by which beam intensities may be optimised is explained. Calculations and experimental measurements in an in-core facility in the DIDO reactor at Harwell have indicated that a DENIS scatterer can achieve a 6-fold improvement in 24.5 keV beam intensity compared with a conventional titanium disc scatterer.

  6. Design of an Improved Type Rotary Inductive Coupling Structure for Rotatable Contactless Power Transfer System

    Directory of Open Access Journals (Sweden)

    Lee Jia-You

    2015-01-01

    Full Text Available This paper is aimed at analyzing the rotary inductive coupling structure of contactless rotary transformer. The main feature of the proposed rotatable contactless power transfer system is which winding is coaxial-interlayered for improving the magnetic coupling capability. There is no ferrite core used in the secondary-side of the rotary inductive coupling structure, this helps to ease the exerted force that is stress by the secondary-side on spindle. In order to verify the feasibility of the proposed contactless power transfer system for rotary applications, an inductive powered rotary machinery and the control system have been integrated. The experimental results show that the maximum power transfer efficiency of the proposed rotary inductive coupling structure is about 94.8%. The maximum output power received in the load end is 1030 W with transmission efficiency of 88%.

  7. Quantifying the Economic and Grid Reliability Impacts of Improved Wind Power Forecasting

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Qin; Martinez-Anido, Carlo Brancucci; Wu, Hongyu; Florita, Anthony R.; Hodge, Bri-Mathias

    2016-10-01

    Wind power forecasting is an important tool in power system operations to address variability and uncertainty. Accurately doing so is important to reducing the occurrence and length of curtailment, enhancing market efficiency, and improving the operational reliability of the bulk power system. This research quantifies the value of wind power forecasting improvements in the IEEE 118-bus test system as modified to emulate the generation mixes of Midcontinent, California, and New England independent system operator balancing authority areas. To measure the economic value, a commercially available production cost modeling tool was used to simulate the multi-timescale unit commitment (UC) and economic dispatch process for calculating the cost savings and curtailment reductions. To measure the reliability improvements, an in-house tool, FESTIV, was used to calculate the system's area control error and the North American Electric Reliability Corporation Control Performance Standard 2. The approach allowed scientific reproducibility of results and cross-validation of the tools. A total of 270 scenarios were evaluated to accommodate the variation of three factors: generation mix, wind penetration level, and wind fore-casting improvements. The modified IEEE 118-bus systems utilized 1 year of data at multiple timescales, including the day-ahead UC, 4-hour-ahead UC, and 5-min real-time dispatch. The value of improved wind power forecasting was found to be strongly tied to the conventional generation mix, existence of energy storage devices, and the penetration level of wind energy. The simulation results demonstrate that wind power forecasting brings clear benefits to power system operations.

  8. Performance analysis of an improved dynamic power management model in wireless sensor node

    Directory of Open Access Journals (Sweden)

    Anuradha Pughat

    2017-02-01

    Full Text Available The energy consumption in the wireless sensor networks is a very critical issue which attracts immediate attention for the sake of the growing demand of the billion dollar market in future. The Dynamic Power Management (DPM technique is a way of controlling and saving the energy usage in a sensor node. Previously, researchers have proposed lifetime improving stochastic models for wireless sensor networks and limited work has been done focusing on the wireless sensor node. This paper proposes an analyser based Semi-Markov model for DPM in the event-driven sensor node. The power consumption comparison with previously proposed models without this analyser shows the analyser significant contributes to lifetime improvement. The improved model is more power efficient, presents how the DPM model observes the input event arrival and power states of the sensor node components, and then dynamically manages the power consumption of the overall system. Further, to observe the effect of event arrival, missed events, waiting time, processor utilization on the power consumption and lifetime, the proposed DPM system with the single server queuing model is developed.

  9. Improving power output of inertial energy harvesters by employing principal component analysis of input acceleration

    Science.gov (United States)

    Smilek, Jan; Hadas, Zdenek

    2017-02-01

    In this paper we propose the use of principal component analysis to process the measured acceleration data in order to determine the direction of acceleration with the highest variance on given frequency of interest. This method can be used for improving the power generated by inertial energy harvesters. Their power output is highly dependent on the excitation acceleration magnitude and frequency, but the axes of acceleration measurements might not always be perfectly aligned with the directions of movement, and therefore the generated power output might be severely underestimated in simulations, possibly leading to false conclusions about the feasibility of using the inertial energy harvester for the examined application.

  10. CO{sub 2} capture efficiency and energy requirement analysis of power plant using modified calcium-based sorbent looping cycle

    Energy Technology Data Exchange (ETDEWEB)

    Li, Y.J.; Zhao, C.S.; Chen, H.C.; Ren, Q.Q.; Duan, L.B. [Southeast University, Nanjing (China). School of Energy & Environment

    2011-03-15

    This paper examines the average carbonation conversion, CO{sub 2} capture efficiency and energy requirement for post-combustion CO{sub 2} capture system during the modified calcium-based sorbent looping cycle. The limestone modified with acetic acid solution, i.e. calcium acetate is taken as an example of the modified calcium-based sorbents. The modified limestone exhibits much higher average carbonation conversion than the natural sorbent under the same condition. The CO{sub 2} capture efficiency increases with the sorbent flow ratios. Compared with the natural limestone, much less makeup mass flow of the recycled and the fresh sorbent is needed for the system when using the modified limestone at the same CO{sub 2} capture efficiency. Achieving 0.95 of CO{sub 2} capture efficiency without sulfation, 272 kJ/mol CO{sub 2} is required in the calciner for the natural limestone, whereas only 223 kJ/mol CO{sub 2} for the modified sorbent. The modified limestone possesses greater advantages in CO{sub 2} capture efficiency and energy consumption than the natural sorbent. When the sulfation and carbonation of the sorbents take place simultaneously, more energy is required. It is significantly necessary to remove SO{sub 2} from the flue gas before it enters the carbonator in order to reduce energy consumption in the calciner.

  11. Solid Adsorbents for Low Temperature CO2 Capture with Low Energy Penalties Leading to More Effective Integrated Solutions for Power Generation and Industrial Processes

    Directory of Open Access Journals (Sweden)

    Nannan eSun

    2015-03-01

    Full Text Available CO2 capture represents the key technology for CO2 reduction within the framework of CO2 capture, utilization, and storage (CCUS. In fact, the implementation of CO2 capture extends far beyond CCUS since it will link the CO2 emission and recycling sectors, and when renewables are used to provide necessary energy input, CO2 capture would enable a profitable zero- or even negative-emitting and integrated energy-chemical solution. To this end, highly efficient CO2 capture technologies are needed, and adsorption using solid adsorbents has the potential to be one of the ideal options. Currently, the greatest challenge in this area is the development of adsorbents with high performance that balances a range of optimization-needed factors, those including costs, efficiency, and engineering feasibility. In this review, recent advances on the development of carbon-based and immobilized organic amines-based CO2 adsorbents are summarized, the selection of these particular categories of materials is because they are among the most developed low temperature (<100 oC CO2 adsorbents up to date, which showed important potential for practical deployment at pilot-scale in the near future. Preparation protocols, adsorption behaviors as well as pros and cons of each type of the adsorbents are presented, it was concluded that encouraging results have been achieved already, however, the development of more effective adsorbents for CO2 capture remains challenging and further innovations in the design and synthesis of adsorbents are needed.

  12. The continuous improvement system of nuclear power plant of Laguna Verde; El sistema de mejora continua de la central nucleoelectrica Laguna Verde

    Energy Technology Data Exchange (ETDEWEB)

    Rivera C, A. [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Km. 42.5 Cardel-Nautla, Veracruz (Mexico)], e-mail: arr99999@cfe.gob.mx

    2009-10-15

    This paper describes the continuous improvement system of nuclear power plant of Laguna Verde and the achievements in implementing the same and additionally two study cases are presents. In February 2009 is noteworthy because the World Association of Nuclear Operators we identified as a learning organization, qualification which shows that the continuous improvement system has matured, and this system will expose as I get to learn to capitalize on our own experiences and external experiences diffused by the nuclear industry. In 2007 the management of nuclear power plants integrates its improvement systems and calls it continuous improvement system and is presented in the same extensive report that won the National Quality Award. This system is made up of 5 subsystems operating individually and are also related 1) human performance; 2) referential comparison or benchmarking; 3) self-assessment; 4) corrective action and 5) external operating experience. Five subsystems that plan, generate, capture, manage, communicate and protect the knowledge generated during the processes execution of nuclear power plant of Laguna Verde, as well as from external sources. The target set in 2007 was to increase the intellectual capital to always give response to meeting the security requirements, but creating a higher value to quality, customer, environment protection and society. In brief each of them, highlighting the objective, expectations management, implementation and some benefits. At the end they will describe two study cases selected to illustrate these cases as the organization learns by their continuous improvement system. (Author)

  13. POWER FACTOR IMPROVEMENT IN THREE PHASE AC-AC CONVERTER THROUGH MODIFIED SPWM

    Directory of Open Access Journals (Sweden)

    P.VASUKI,

    2011-02-01

    Full Text Available Recently, a new generation of ac-ac single-phase and three-phase power converters with more commutations per half cycle has been proposed for ac power due to the increasing availability and power capability of high frequency controlled-on and off power emiconductor switching devices. This paper presents three phase ac-acconverter whose control strategy is based on modified sinusoidal ulse-width modulation switching technique. As majority of the industrial loads are being inductive, the power factor is less. To improve the power factor, the delayed current is shifted to the input voltage, through a modification of the classical sinusoidal pulse width modulation switching technique. In this way, the decrease in the phase angle between the input current and voltage is feasible, and consequently, high cost compensation capacitors can be avoided. The improvement of power factor through this switching technique on the proposed converter is investigated and verified via simulation using the software Matlab/Simulink.

  14. IMPROVEMENT OF TRANSIENT STABILITY OF POWER SYSTEM USING SOLID STATE CIRCUIT BREAKER

    Directory of Open Access Journals (Sweden)

    Kalai Murugan Amirthalingam

    2013-01-01

    Full Text Available The aim of this study is to use a solid state circuit breaker for the improvement of transient stability margin. Long distance AC transmission is often subject to stability problems, which limits the transmission capability. Interconnected power systems suffer from weakly damped swings between synchronous generator and sub systems. The development of modern power system has lead to an increasing complexity in the study of power system and also presents new challenges to power system stability and in particular to the aspects of transient stability and small signal stability. Transient stability control plays a significant role in ensuring the stable operation of power systems in the event of large disturbances and faults and is thus a significant area of research. This study investigates the improvement of transient stability of a two area system, using Solid State Circuit Breaker which is capable of fast switching in case of faults and thus controlling the real and reactive power flows in a faulted transmission line. Simulations are carried out in Matlab/Simulink environment for two area system model with Solid State Circuit Breaker to analyze the effects of SSCB on transient stability performance of the system. From the simulation results, swing curves of the three phase faulted power system without SSCB gets increases monotonically and thus the system can be considered as unstable whereas the swing curves of the system with an SSCB reaches to a steady state.

  15. Improvement of Power Quality using Fuzzy Logic Controller In Grid Connected Photovoltaic Cell Using UPQC

    Directory of Open Access Journals (Sweden)

    K.Ramalingeswara Rao

    2014-07-01

    Full Text Available In this paper, the design of combined operation of UPQC and PV-ARRAY is designed. The proposed system is composed of series and shunt inverters connected back to back by a dc-link to which pv-array is connected. This system is able to compensate voltage and current related problems both in inter-connected mode and islanding mode by injecting active power to grid. The fundamental aspect is that the power electronic devices (PE and sensitive equipments (SE are normally designed to work in non-polluted power system, so they would suffer from malfunctions when supply voltage is not pure sinusoidal. Thus this proposed operating strategy with flexible operation mode improves the power quality of the grid system combining photovoltaic array with a control of unified power quality conditioner. Pulse Width Modulation (PWM is used in both three phase four leg inverters. A Proportional Integral (PI and Fuzzy Logic Controllers are used for power quality improvement by reducing the distortions in the output power. The simulated results were compared among the two controller’s strategies With pi controller and fuzzy logic controller

  16. Improved Structure and Fabrication of Large, High-Power KHPS Rotors - Final Scientific/Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Corren, Dean [Verdant Power, Inc.; Colby, Jonathan [Verdant Power, Inc.; Adonizio, Mary Ann [Verdant Power, Inc.

    2013-01-29

    Verdant Power, Inc, working in partnership with the National Renewable Energy Laboratory (NREL), Sandia National Laboratories (SNL), and the University of Minnesota St. Anthony Falls Laboratory (SAFL), among other partners, used evolving Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA) models and techniques to improve the structure and fabrication of large, high-power composite Kinetic Hydropower System (KHPS) rotor blades. The objectives of the project were to: design; analyze; develop for manufacture and fabricate; and thoroughly test, in the lab and at full scale in the water, the improved KHPS rotor blade.

  17. Improvements of Power Factor and Torque of a Synchronous Reluctance Motor with a Slit Rotor

    Science.gov (United States)

    Nashiki, Masayuki; Inoue, Yoshimitu; Kawai, Youichi; Yokochi, Takanori; Satake, Akiyoshi; Okuma, Shigeru

    Power factor and torque of synchronous reluctance motors with a slit rotor are studied. In there stators, divided teeth made of powder magnetic core are adopted and windings are improved to get high space factor of stator windings and to shorten coil ends. In there rotors, stainless sheets are inserted among soft magnetic metal sheets with adhesive to strengthen the rotors and rotor structure is improved to enlarge the saliency ratio (Ld/Lq). As the result, the power factor 0.78 and 1.6 times torque at same motor size are attained.

  18. Optimized Solvent for Energy-Efficient, Environmentally-Friendly Capture of CO{sub 2} at Coal-Fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Farthing, G. A.; Rimpf, L. M.

    2014-04-30

    The overall goal of this project, as originally proposed, was to optimize the formulation of a novel solvent as a critical enabler for the cost-effective, energy-efficient, environmentally-friendly capture of CO{sub 2} at coal-fired utility plants. Aqueous blends of concentrated piperazine (PZ) with other compounds had been shown to exhibit high rates of CO{sub 2} absorption, low regeneration energy, and other desirable performance characteristics during an earlier 5-year development program conducted by B&W. The specific objective of this project was to identify PZ-based solvent formulations that globally optimize the performance of coal-fired power plants equipped with CO{sub 2} scrubbing systems. While previous solvent development studies have tended to focus on energy consumption and absorber size, important issues to be sure, the current work seeks to explore, understand, and optimize solvent formulation across the full gamut of issues related to commercial application of the technology: capital and operating costs, operability, reliability, environmental, health and safety (EH&S), etc. Work on the project was intended to be performed under four budget periods. The objective of the work in the first budget period has been to identify several candidate formulations of a concentrated PZ-based solvent for detailed characterization and evaluation. Work in the second budget period would generate reliable and comprehensive property and performance data for the identified formulations. Work in the third budget period would quantify the expected performance of the selected formulations in a commercial CO{sub 2} scrubbing process. Finally, work in the fourth budget period would provide a final technology feasibility study and a preliminary technology EH&S assessment. Due to other business priorities, however, B&W has requested that this project be terminated at the end of the first budget period. This document therefore serves as the final report for this project. It

  19. A low power 12-bit 1 Msps successive approximation register ADC with an improved switching procedure

    Science.gov (United States)

    Fubin, Xin; Tao, Yin; Qisong, Wu; Yuanlong, Yang; Fei, Liu; Haigang, Yang

    2015-08-01

    As a key building block of data acquisition systems, power dissipation of the successive approximation register (SAR) ADC determines the total power consumption of the system. In this paper, a low power 12-bit 1 Msps SAR ADC with an improved switching procedure is presented. Power consumption and area occupation could be significantly reduced by using the proposed switching procedure. Compared to converters that use the conventional switching procedure, the average switching energy could be reduced by about 80% and the total capacitance could be reduced by 50%. A simplified digital control logic is utilized to reduce power dissipation and area occupation of the digital control circuits. Simulation results show that the power dissipated by the proposed digital control circuits could be reduced by about 50% compared to the power dissipated by conventional control circuits. The chip has been processed in a standard 0.35 μm CMOS technology and has a core die area of 1.12 mm2. A signal-to-noise-and-distortion-ratio of 64.2 dB has been measured with a 100 kHz signal input under a wide range variation of temperature from -55 to 150 °C. The total power consumption of the prototype is only 0.72 mW with a 3.3 V supply voltage. Project supported by the National Basic Research Program of China (No. 2014CB744600) and the National Natural Science Foundation of China (No. 61474120).

  20. Improvement of Power Flow Calculation with Optimization Factor Based on Current Injection Method

    Directory of Open Access Journals (Sweden)

    Lei Wang

    2014-01-01

    Full Text Available This paper presents an improvement in power flow calculation based on current injection method by introducing optimization factor. In the method proposed by this paper, the PQ buses are represented by current mismatches while the PV buses are represented by power mismatches. It is different from the representations in conventional current injection power flow equations. By using the combined power and current injection mismatches method, the number of the equations required can be decreased to only one for each PV bus. The optimization factor is used to improve the iteration process and to ensure the effectiveness of the improved method proposed when the system is ill-conditioned. To verify the effectiveness of the method, the IEEE test systems are tested by conventional current injection method and the improved method proposed separately. Then the results are compared. The comparisons show that the optimization factor improves the convergence character effectively, especially that when the system is at high loading level and R/X ratio, the iteration number is one or two times less than the conventional current injection method. When the overloading condition of the system is serious, the iteration number in this paper appears 4 times less than the conventional current injection method.

  1. Heat-Rate Improvement Obtained by Retubing Power-Plant Condenser Enhanced Tubes

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-21

    A utility will only retube a condenser with enhanced tubes if the incremental cost of the enhanced tubes can be offset with reduced fuel costs. The reduced fuel cost is obtained for some units because of the higher heat-transfer coefficient of enhanced tubes. They lead to improved condenser performance measured by a lower condenser pressure and therefore a more efficient power plant. However, the higher haet-transfer coefficients do not always guarantee that enhanced tubes will be more cost effective. Other issues must be considered such as the cooling-water flow reduction due to the increased pressure drop, the low-pressure turbine heat-rate variation with backpressure, and the cooling-water pump and system characteristics. These and other parameters must be considered to calculate the efficiency improvement of the power plant as commonly measured by the quantity known as the heat rate. Knowing the heat-rate improvement, the fuel cost, and the incremental increase of the enhanced tubes from the supplier, the payback time can be determined. This program calculates the heat-rate improvement that can be obtained by retubing a power plant condenser with enhanced tubes of a particular type called Korodense LPD made by Wolverine Tube, Inc. The fuel savings are easily established knowing the heat-rate improvement. All electrical utilities are potential users because a condenser is used as the heat sink for every power plant.

  2. HTRATE; Heat-Rate Improvement Obtained by Retubing Power-Plant Condenser Enhanced Tubes

    Energy Technology Data Exchange (ETDEWEB)

    Rabas, T.J. [Argonne National Lab., IL (United States)

    1990-06-01

    A utility will only retube a condenser with enhanced tubes if the incremental cost of the enhanced tubes can be offset with reduced fuel costs. The reduced fuel cost is obtained for some units because of the higher heat-transfer coefficient of enhanced tubes. They lead to improved condenser performance measured by a lower condenser pressure and therefore a more efficient power plant. However, the higher haet-transfer coefficients do not always guarantee that enhanced tubes will be more cost effective. Other issues must be considered such as the cooling-water flow reduction due to the increased pressure drop, the low-pressure turbine heat-rate variation with backpressure, and the cooling-water pump and system characteristics. These and other parameters must be considered to calculate the efficiency improvement of the power plant as commonly measured by the quantity known as the heat rate. Knowing the heat-rate improvement, the fuel cost, and the incremental increase of the enhanced tubes from the supplier, the payback time can be determined. This program calculates the heat-rate improvement that can be obtained by retubing a power plant condenser with enhanced tubes of a particular type called Korodense LPD made by Wolverine Tube, Inc. The fuel savings are easily established knowing the heat-rate improvement. All electrical utilities are potential users because a condenser is used as the heat sink for every power plant.

  3. Improvement of Initiating Events Analsis in Low-Power and Shutdown PSA for Korea Standard Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Jee; Jang, Seung Chul; Lim, Ho Gon

    2005-04-15

    In this study, we have improved the methodology of the initiating event identification for the KSNP LPSD PSA to complement the deficiency obtained from Review of KSNP LPSD PSA Mode based on ANS LPSD PSA Standard. To improve the quality of initiating event analysis, we integrated three systematic approachs for this purpose such as Master Logic Diagram, the empirical approach using domestic and international operating experience and the engineering approach. And we have identified 22 initiation events finally. We could got a basis and satisfied a structured, systematic process for initiating event identification demanded in ANS LPSD PSA Standard. But the sufficient completeness of initiating event analysis for LPSD PSA, the domestic low power and shutdown operating experience for overhaul and un-planed outages analysis is also needed.

  4. A High Intensity Interval Training (HIIT)-Based Running Plan Improves Athletic Performance by Improving Muscle Power.

    Science.gov (United States)

    García-Pinillos, Felipe; Cámara-Pérez, Jose C; Soto-Hermoso, Víctor M; Latorre-Román, Pedro Á

    2017-01-01

    García-Pinillos, F, Cámara-Pérez, JC, Soto-Hermoso, VM, and Latorre-Román, PÁ. A High Intensity Interval Training (HIIT)-based running plan improves athletic performance by improving muscle power. J Strength Cond Res 31(1): 146-153, 2017-This study aimed to examine the effect of a 5-week high-intensity intermittent training (HIIT)-based running plan on athletic performance and to compare the physiological and neuromuscular responses during a sprint-distance triathlon before and after the HIIT period. Thirteen triathletes were matched into 2 groups: the experimental group (EG) and the control group (CG). The CG was asked to maintain their normal training routines, whereas the EG maintained only their swimming and cycling routines and modified their running routine. Participants completed a sprint-distance triathlon before (pretest) and after (posttest) the intervention period. In both pretest and posttest, the participants performed 4 jumping tests: before the race (baseline), postswim, postcycling, and postrun. Additionally, heart rate was monitored (HRmean), whereas rate of perceived exertion (RPE) and blood lactate accumulation (BLa) were registered after the race. No significant differences (p ≥ 0.05) between groups were found before HIIT intervention (at pretest). Significant group-by-training interactions were found in vertical jumping ability and athletic performance: the EG improved jumping performance (∼6-9%, p ≤ 0.05, effect size (ES) > 0.7), swimming performance (p = 0.013, ES = 0.438), and running time (p = 0.001, ES = 0.667) during the competition, whereas the CG remained unchanged (p ≥ 0.05, ES HIIT-based running plan combined with the high training volumes of these triathletes in swimming and cycling improved athletic performance during a sprint-distance triathlon. This improvement may be due to improved neuromuscular characteristics that were transferred into improved muscle power and work economy.

  5. Improvement of High-Power Three-Level Explosion-Proof Inverters Using Soft Switching Control Based on Optimized Power-Loss Algorithm

    Directory of Open Access Journals (Sweden)

    Shi-Zhou Xu

    2015-01-01

    Full Text Available The high-power three-level explosion-proof inverters demand high thermal stability of power devices, and a set of theories and methods is needed to achieve an accurate power-loss calculation of power devices, to establish heat dissipation model, and ultimately to reduce the power loss to improve thermal stability of system. In this paper, the principle of neutral point clamped three-level (NPC3L inverter is elaborated firstly, and a fourth-order RC equivalent circuit of IGBT is derived, on which basis the power-loss model of IGBT and the optimized maternal power-loss thermal model, using an optimized power-loss algorithm, are established. Secondly, in accordance with the optimized maternal power-loss thermal model, the generic formulas of power-loss calculation are deduced to calculate the power-loss modification values of NPC3L and soft switching three-level (S3L inverters, which will be the thermal sources during thermal analysis for maternal power-loss thermal models. Finally, the experiment conducted on the 2.1 MW experimental platform shows that S3L inverter has the same excellent output characteristics with NPC3L inverter, reduces the power loss significantly by 213 W in each half-bridge, and decreases the temperature by 10°C, coinciding with the theoretical calculation, which verifies the accuracy of optimized power-loss algorithm and the effectiveness of the improvement.

  6. Improved performance of high average power semiconductor arrays for applications in diode pumped solid state lasers

    Energy Technology Data Exchange (ETDEWEB)

    Beach, R.; Emanuel, M.; Benett, W.; Freitas, B.; Ciarlo, D.; Carlson, N.; Sutton, S.; Skidmore, J.; Solarz, R.

    1994-01-01

    The average power performance capability of semiconductor diode laser arrays has improved dramatically over the past several years. These performance improvements, combined with cost reductions pursued by LLNL and others in the fabrication and packaging of diode lasers, have continued to reduce the price per average watt of laser diode radiation. Presently, we are at the point where the manufacturers of commercial high average power solid state laser systems used in material processing applications can now seriously consider the replacement of their flashlamp pumps with laser diode pump sources. Additionally, a low cost technique developed and demonstrated at LLNL for optically conditioning the output radiation of diode laser arrays has enabled a new and scalable average power diode-end-pumping architecture that can be simply implemented in diode pumped solid state laser systems (DPSSL`s). This development allows the high average power DPSSL designer to look beyond the Nd ion for the first time. Along with high average power DPSSL`s which are appropriate for material processing applications, low and intermediate average power DPSSL`s are now realizable at low enough costs to be attractive for use in many medical, electronic, and lithographic applications.

  7. Analysis of Power Quality Based on Real Data and Quality Improvement at Campus Distribution System

    Science.gov (United States)

    Kawasaki, Shoji; Matsuki, Junya; Hayashi, Yasuhiro; Ito, Akitoshi

    In recent years, a lot of equipments have been made using the inverter technology from home electric appliances to office automation apparatuses and industrial equipments with the development of power electronics technology. The voltage distortion of a distribution system has increased due to the harmonic currents generated from these apparatuses, and the increase in harmonics continues to be expected. In addition, the distribution system forms the circuit of harmonic distortion expansion by the prevalence of static capacitor without L for power factor improvement. Moreover, the voltage imbalance occurs by diversification of loads or imbalanced connection of single-phase loads. The deterioration of power quality in the distribution system causes various problems such as the overheating of equipments and malfunction of rotating machines. Since the power quality changes according to air temperature and date, it is desirable to measure the voltages and currents continuously for a long time. In this study, the authors focus attention on the distribution system in the University of Fukui campus, and the authors have measured the voltages and currents in the distribution system for a long period with WAMS (Wide Area Measurement System) using NCT (Network Computing Terminal). Based on the obtained data, the authors analyzed the power quality of the campus distribution system from viewpoints of voltage imbalance, current imbalance, voltage THD (Total Harmonic Distortion), and current THD. Furthermore, the improvement effect of power quality of the campus distribution system by exchange of single-phase load connection is described.

  8. Ion Cleaning of Facets for Improving the Reliability of High Power 980 nm Semiconductor Lasers

    Institute of Scientific and Technical Information of China (English)

    SHU Xiong-Wen; XU Chen; TIAN Zeng-Xia; SHEN Guang-Di

    2006-01-01

    We report a simple and available way of improving the reliability of high power InGaAs 980 nm lasers by cleaning the facets using Ar ion before the protecting films have been coated. The Ar cleaning can remove the impurity and the oxide on the air-cleaved facets of laser diodes. It is proven that the way has marked effect on reducing the gradual degradation rate of laser diodes and improving the catastrophic-optical-damage threshold.

  9. Chronic eccentric cycling improves quadriceps muscle structure and maximum cycling power.

    Science.gov (United States)

    Leong, C H; McDermott, W J; Elmer, S J; Martin, J C

    2014-06-01

    An interesting finding from eccentric exercise training interventions is the presence of muscle hypertrophy without changes in maximum concentric strength and/or power. The lack of improvements in concentric strength and/or power could be due to long lasting suppressive effects on muscle force production following eccentric training. Thus, improvements in concentric strength and/or power might not be detected until muscle tissue has recovered (e. g., several weeks post-training). We evaluated alterations in muscular structure (rectus-femoris, RF, and vastus lateralis, VL, thickness and pennation angles) and maximum concentric cycling power (Pmax) 1-week following 8-weeks of eccentric cycling training (2×/week; 5-10.5 min; 20-55% of Pmax). Pmax was assessed again at 8-weeks post-training. At 1 week post-training, RF and VL thickness increased by 24±4% and 13±2%, respectively, and RF and VL pennation angles increased by 31±4% and 13±1%, respectively (all Peccentric cycling can be a time-effective intervention for improving muscular structure and function in the lower body of healthy individuals. The larger Pmax increase detected at 8-weeks post-training implies that sufficient recovery might be necessary to fully detect changes in muscular power after eccentric cycling training.

  10. Transient Stability Improvement of Multi-Machine Power System with Large-Capacity Battery Systems

    Science.gov (United States)

    Kawabe, Ken-Ichi; Yokoyama, Akihiko

    An emergency control has been applied to power systems to avoid cascading outages by making the best use of existing equipment under severe fault conditions. Battery energy storage system (BESS) is one of the attractive equipment for the emergency control according to its growing installed capacity in the current grid. This paper investigates an effective use of BESS for transient stability improvement, and proposes a novel control scheme using wide-area information. The proposed control scheme adopts two stability indices, the energy function and rotor speed of the critical machine, to make it applicable to multi-machine power systems. Besides, it can control active and reactive power injection of the BESS coordinately to make the best use of its converter capacity for the stability enhancement. Digital simulations are conducted on the 32-machine meshed system with multiple BESSs. The results demonstrate that the BESSs controlled by the proposed method can improve the first swing stability and the system damping, and it is made clear how they improve the transient stability of the multi-machine power system. In addition, an impact of the reactive power control on the bus voltages around the installation sites is investigated to discuss a preferable way of their installation.

  11. The economic valuation on atmospheric improvement benefit by nuclear power generation

    Energy Technology Data Exchange (ETDEWEB)

    Kwak, S. J.; Yoo, S. H.; Han, S. Y.; Do, G. W.; Lee, J. S. [Korea Univ., Seoul (Korea)

    2000-12-01

    The major contents are as follows : To begin with, major air pollutants' emissions and emission reduction facilities in industrial sectors including a power generation were investigated and the future prospect was suggested. Environmental effects by attributes of air pollutions were summarized through a extensive literature survey. And the concept of benefit-cost based upon social costs and economic values of generation was established to estimate atmospheric improvement benefits by using a nuclear power. As a result of investigating many valuation methodologies that can estimate economic values of environmental improvement, we adopted MAUA(multi-attribute utility assessment) as a research method and estimated environmental costs by air pollutant and by power generating source. Also, we presented foreign case studies related to social costs in power generating sector and horizontally compared study's results home and abroad. Then, we set up four scenarios based on total generation that the 5th long-term power resources planning forecasted and calculated economic values of atmospheric improvement benefits among scenarios. Further, we suggested the results incorporating uncertainty of estimation parameters. Finally, we suggested a rational ground to move toward environment-friendly energy consumption and proposed a plan for the national energy policy against the green age in the 21th century. 147 refs., 45 figs., 103 tabs. (Author)

  12. Power Quality Improvement Using Cascaded H-Bridge Multilevel Inverter Based Dstatcom

    Directory of Open Access Journals (Sweden)

    B. Suryajitt,

    2014-11-01

    Full Text Available Cascaded multilevel configuration of the inverter has the advantage of its simplicity and modularity over the configurations of the diode-clamped and flying capacitor multilevel inverters. This paper presents a threephase, five-level and seven level cascaded multilevel voltage source inverter based active filter for power line conditioning to improve power quality in the distribution network. The DSTATCOM helps to improve the power factor and eliminate the Total Harmonics Distortion (THD drawn from a Non-Liner Diode Rectifier Load (NLDRL. The compensation process is based on concept of p-q theory. A CHB Inverter is considered for shunt compensation of a 11 kV distribution system. Finally a level shifted PWM (LSPWM and phase shifted PWM (PSPWM techniques are adopted to investigate the performance of CHB Inverter. The results are obtained through Matlab/Simulink software package.

  13. Evaluation of Performance and Opportunities for Improvements in Automotive Power Electronics Systems: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, Gilberto; Bennion, Kevin; King, Charles; Narumanchi, Sreekant

    2016-06-14

    Thermal management strategies for automotive power electronic systems have evolved over time to reduce system cost and to improve reliability and thermal performance. In this study, we characterized the power electronic thermal management systems of two electric-drive vehicles--the 2012 Nissan LEAF and 2014 Honda Accord Hybrid. Tests were conducted to measure the insulated-gate bipolar transistor-to-coolant thermal resistances for both steady-state and transient conditions at various coolant flow rates. Water-ethylene glycol at a temperature of 65 degrees C was used as the coolant for these experiments. Computational fluid dynamics and finite element analysis models of the vehicle's power electronics thermal management system were then created and validated using experimentally obtained results. Results indicate that the Accord module provides lower steady-state thermal resistance as compared with the LEAF module. However, the LEAF design may provide improved performance in transient conditions and may have cost benefits.

  14. An improved maximum power point tracking method for a photovoltaic system

    Science.gov (United States)

    Ouoba, David; Fakkar, Abderrahim; El Kouari, Youssef; Dkhichi, Fayrouz; Oukarfi, Benyounes

    2016-06-01

    In this paper, an improved auto-scaling variable step-size Maximum Power Point Tracking (MPPT) method for photovoltaic (PV) system was proposed. To achieve simultaneously a fast dynamic response and stable steady-state power, a first improvement was made on the step-size scaling function of the duty cycle that controls the converter. An algorithm was secondly proposed to address wrong decision that may be made at an abrupt change of the irradiation. The proposed auto-scaling variable step-size approach was compared to some various other approaches from the literature such as: classical fixed step-size, variable step-size and a recent auto-scaling variable step-size maximum power point tracking approaches. The simulation results obtained by MATLAB/SIMULINK were given and discussed for validation.

  15. An Improvement of a Fuzzy Logic-Controlled Maximum Power Point Tracking Algorithm for Photovoltic Applications

    Directory of Open Access Journals (Sweden)

    Woonki Na

    2017-03-01

    Full Text Available This paper presents an improved maximum power point tracking (MPPT algorithm using a fuzzy logic controller (FLC in order to extract potential maximum power from photovoltaic cells. The objectives of the proposed algorithm are to improve the tracking speed, and to simultaneously solve the inherent drawbacks such as slow tracking in the conventional perturb and observe (P and O algorithm. The performances of the conventional P and O algorithm and the proposed algorithm are compared by using MATLAB/Simulink in terms of the tracking speed and steady-state oscillations. Additionally, both algorithms were experimentally validated through a digital signal processor (DSP-based controlled-boost DC-DC converter. The experimental results show that the proposed algorithm performs with a shorter tracking time, smaller output power oscillation, and higher efficiency, compared with the conventional P and O algorithm.

  16. Improving the Power Quality of Six Parallel Operated Onshore Wind Turbines using UPFC

    Directory of Open Access Journals (Sweden)

    N. Archana

    2015-08-01

    Full Text Available This study is aimed at improving the power quality of an onshore wind turbine connected to the grid, using a Unified Power Factor Controller. A six parallel operated onshore wind turbine is used as a model to demonstrate the effectiveness of the proposed system. The wind generating system consists of doubly fed induction generator connected to the wind turbine. An average model of the doubly fed induction generator is used and the control signals are generated using closed loop control. The unified power factor controller is modeled using grid and rotor side converters and controlled using closed loop pulse width modulated signals. The proposed system reduces the reactive power of the system, which is proved by simulating the system using MATLAB SIMULINK environment.

  17. An improved method for stripping cladding light in high power fiber lasers

    Science.gov (United States)

    Li, Tenglong; Wu, Juan; Sun, Yinghong; Wang, Yanshan; Ma, Yi

    2015-02-01

    In order to ensure the high power all-fiber laser reliability and excellent beam quality, it is necessary to strip the unwanted cladding light. The common method for stripping cladding light is to recoat the double cladding fiber with a high index gel, but localized heating and low thermal conductivity of the recoating gel are the prime factors limiting the power-handling capability of the cladding power stripper(CPS). An improved fabrication technique to manufacture the CPS is presented. Light stripping section of the fiber is fused with a transparent quartz tube, by applying different amount of etchant along the quartz tube, frosted surface is created and uniformly removal of the cladding light is achieved. The quartz tube is joined to water-cooled thermal enclosure tightly without the gel to avoid heat aggregation. The power-handling capability of the device is tested under 200W of cladding light, and attenuation of 20 dB is achieved.

  18. An Improved Power Quality Based Sheppard-Taylor Converter Fed BLDC Motor Drive

    Science.gov (United States)

    Singh, Bhim; Bist, Vashist

    2015-12-01

    This paper deals with the design and analysis of a power factor correction based Sheppard-Taylor converter fed brushless dc motor (BLDCM) drive. The speed of the BLDCM is controlled by adjusting the dc link voltage of the voltage source inverter (VSI) feeding BLDCM. Moreover, a low frequency switching of the VSI is used for electronically commutating the BLDCM for reduced switching losses. The Sheppard-Taylor converter is designed to operate in continuous conduction mode to achieve an improved power quality at the ac mains for a wide range of speed control and supply voltage variation. The BLDCM drive is designed and its performance is simulated in a MATLAB/Simulink environment to achieve the power quality indices within the limits of the international power quality standard IEC-61000-3-2.

  19. Using the Power Balance Wristband to Improve Students' Research-Design Skills

    Science.gov (United States)

    Lawson, Timothy J.; Blackhart, Ginette C.; Gialopsos, Brooke M.

    2016-01-01

    We describe an exercise involving the power balance wristband (PBW) designed to enhance students' ability to design scientific tests. An instructor demonstrated that the PBW improved a student's balance, strength, and flexibility and invited students to design and conduct a brief scientific test of the PBW. Research methods students who…

  20. Using domain specific languages to improve the development of a power control unit

    NARCIS (Netherlands)

    Schuts, M.; Hooman, J.

    2015-01-01

    To improve the design of a power control unit at Philips, two Domain Specific Languages (DSLs) have been used. The first DSL provides a concise and readable notation for the essential state transitions. It is used to generate both configuration files and analysis models. In addition, we also generat

  1. Using the Power Balance Wristband to Improve Students' Research-Design Skills

    Science.gov (United States)

    Lawson, Timothy J.; Blackhart, Ginette C.; Gialopsos, Brooke M.

    2016-01-01

    We describe an exercise involving the power balance wristband (PBW) designed to enhance students' ability to design scientific tests. An instructor demonstrated that the PBW improved a student's balance, strength, and flexibility and invited students to design and conduct a brief scientific test of the PBW. Research methods students who…

  2. Formulation, computation and improvement of steady state security margins in power systems. Part II: Results

    Energy Technology Data Exchange (ETDEWEB)

    Echavarren, F.M.; Lobato, E.; Rouco, L.; Gomez, T. [School of Engineering of Universidad Pontificia Comillas, C/Alberto Aguilera, 23, 28015 Madrid (Spain)

    2011-02-15

    A steady state security margin for a particular operating point can be defined as the distance from this initial point to the secure operating limits of the system. Four of the most used steady state security margins are the power flow feasibility margin, the contingency feasibility margin, the load margin to voltage collapse, and the total transfer capability between system areas. This is the second part of a two part paper. Part I has proposed a novel framework of a general model able to formulate, compute and improve any steady state security margin. In Part II the performance of the general model is validated by solving a variety of practical situations in modern real power systems. Actual examples of the Spanish power system will be used for this purpose. The same computation and improvement algorithms outlined in Part I have been applied for the four security margins considered in the study, outlining the convenience of defining a general framework valid for the four of them. The general model is used here in Part II to compute and improve: (a) the power flow feasibility margin (assessing the influence of the reactive power generation limits in the Spanish power system), (b) the contingency feasibility margin (assessing the influence of transmission and generation capacity in maintaining a correct voltage profile), (c) the load margin to voltage collapse (assessing the location and quantity of loads that must be shed in order to be far away from voltage collapse) and (d) the total transfer capability (assessing the export import pattern of electric power between different areas of the Spanish system). (author)

  3. PRELIMINARY TECHNICAL AND ECONOMIC FEASIBILITY STUDY ON THE INTEGRATION OF A PROCESS UTILIZING LOW-ENERGY SOLVENTS FOR CARBON DIOXIDE CAPTURE ENABLED BY A COMBINATION OF ENZYMES AND ULTRASONICS WITH A SUBCRITICAL PC POWER PLANT

    Energy Technology Data Exchange (ETDEWEB)

    Swaminathan, Saravanan; Kuczynska, Agnieszka; Hume, Scott; Mulgundmath, Vinay; Freeman, Charles; Bearden, Mark; Remias, Joe; Ambedkar, Balraj; Salmon, Sonja; House, Alan

    2012-11-01

    The results of the preliminary techno-economic assessment for integrating a process utilizing low-energy solvents for carbon dioxide (CO2) capture enabled by a combination of enzymes and ultrasonics with a subcritical pulverized coal (PC) power plant are presented. Four cases utilizing the enzyme-activated solvent are compared using different methodologies of regeneration against the DOE/NETL reference MEA case. The results are shown comparing the energy demand for post-combustion CO2 capture and the net higher heating value (HHV) efficiency of the power plant integrated with the post-combustion capture (PCC) plant. A levelized cost of electricity (LCOE) assessment was performed showing the costs of the options presented in the study. The key factors contributing to the reduction of LCOE were identified as enzyme make-up rate and the capability of the ultrasonic regeneration process. The net efficiency of the integrated PC power plant with CO2 capture changes from 24.9% with the reference Case 10 plant to between 24.34% and 29.97% for the vacuum regeneration options considered, and to between 26.63% and 31.41% for the ultrasonic regeneration options. The evaluation also shows the effect of the critical parameters on the LCOE, with the main variable being the initial estimation of enzyme dosing rate. The LCOE ($/MWh) values range from 112.92 to 125.23 for the vacuum regeneration options and from 108.9 to 117.50 for the ultrasonic regeneration cases considered in comparison to 119.6 for the reference Case 10. A sensitivity analysis of the effect of critical parameters on the LCOE was also performed. The results from the preliminary techno-economic assessment show that the proposed technology can be investigated further with a view to being a viable alternative to conventional CO2 scrubbing technologies.

  4. Improved Power Conversion Efficiency of Inverted Organic Solar Cells by Incorporating Au Nanorods into Active Layer.

    Science.gov (United States)

    He, Yeyuan; Liu, Chunyu; Li, Jinfeng; Zhang, Xinyuan; Li, Zhiqi; Shen, Liang; Guo, Wenbin; Ruan, Shengping

    2015-07-29

    This Research Article describes a cooperative plasmonic effect on improving the performance of organic solar cells. When Au nanorods(NRs) are incorporated into the active layers, the designed project shows superior enhanced light absorption behavior comparing with control devices, which leads to the realization of organic solar cell with power conversion efficiency of 6.83%, accounting for 18.9% improvement. Further investigations unravel the influence of plasmonic nanostructures on light trapping, exciton generation, dissociation, and charge recombination and transport inside the thin films devices. Moreover, the introduction of high-conductivity Au NRs improves electrical conductivity of the whole device, which contributes to the enhanced fill factor.

  5. Improved Optimization Study of Integration Strategies in Solar Aided Coal-Fired Power Generation System

    Directory of Open Access Journals (Sweden)

    Rongrong Zhai

    2015-01-01

    Full Text Available Solar aided coal-fired power generation system (SACFPGS combines solar energy and traditional coal-fired units in a particular way. This study mainly improves the solar thermal storage system. Genetic algorithm is used to optimize the SACFPGS. The best integration approach of the system, the collector area, and the corresponding thermal storage capacity to replace each high-pressure extraction are obtained when the amount of coal saving in unit solar investment per hour is at its largest. System performance before and after the improvement is compared. Results show that the improvement of the thermal storage system effectively increases the economic benefit of the integrated system.

  6. Improvement of power system stability by high speed power control of adjustable speed machine; Kahensokuki no koshutsuryoku seigyo ni yoru denryoku keito no anteido kojo

    Energy Technology Data Exchange (ETDEWEB)

    Nojiri, K.; Kikuchi, T.; Nakagawa, H. [Kansai Electric Power Co. Inc., Osaka (Japan); Goto, M. [Hitachi, Ltd., Tokyo (Japan); Nohara, H. [Hitachi Nuclear Engineering Co. Ltd., Tokyo (Japan)

    1997-01-20

    Large capacity adjustable speed machines (ASMs) at pumped storage power station have been put into full operation and the operating characteristics of ASM have been highly evaluated from the view point of power system operation. The output power (input power) of ASM can be controlled very quickly by applying a vector control scheme to the excitation control. This quick responsive feature of ASM can make it possible to improve the stability of the neighbor sub-power system. For improvement of transient stability, the output power of ASM is reduced very quickly in order to control the acceleration of neighbor generators during and after transmission line faults. For improvement of dynamic stability, the output power of ASM is modulated in accordance with the stabilizing signals detected from the swing of generator rotor or the power flow fluctuation on the transmission line. This paper describes the design concepts and method of control system for improving the transient and dynamic stability and proposes a power system stabilizing control system. The effects of the proposed stabilizing control system have been verified by a power system simulator. 9 refs., 15 figs., 1 tab.

  7. Using MapReduce to Improve the Power Generation of the International Space Station

    Science.gov (United States)

    Marchetto, William R., II

    The International Space Station (ISS) spends approximately 98% of its time in orbits that experience Earth eclipse. Since the station's solar arrays produce no power when in Earth's shadow, the total power generated decreases substantially, lowering the power budget available to experimental payloads. Therefore, increasing the power output during these eclipsed orbits would be of great benefit to the space station's scientific endeavors. The ISS's current solar array configuration tracks the Sun throughout each orbit, keeping each of its 16 solar panels perpendicular to the Sun at all times. While this is the optimal orientation for solar panels with unobstructed views of the Sun, the space station's solar arrays experience shadowing from the spacecraft's structure as well as from the other solar panels. Deviating from the Sun-tracking scheme at strategic points in certain orbits can provide an increase in power output. The goal of this research was to provide a programmatic solution that increases the power generation capabilities of the ISS in orbits experiencing Earth-eclipse without requiring any physical modifications to the space station's structure. To achieve this goal, a simulator was developed to model the ISS-Earth-Sun environment and calculate the power output of the station's solar arrays based on each panel's orientation and shadowing. Many combinations of array configurations were analyzed, taking into account the physical constraints of the gimbals responsible for rotating the solar panels. The power output of the ISS was improved for the subset of Earth-eclipsed orbits that experience a high degree of shadowing from the station's structure, resulting in an average energy increase of 1.08 kWh per orbit. The power gains were achieved by quickly rotating the solar arrays through the points in each orbit that experienced the highest degree of shadowing.

  8. The potential role of natural gas power plants with carbon capture and storage as a bridge to a low-carbon future

    Science.gov (United States)

    The CO2 intensity of electricity produced by state-of-the-art natural gas combined-cycle turbines (NGCC) is approximately one-third that of the U.S. fleet of existing coal plants. Compared to new nuclear plants and coal plants with integrated carbon capture, NGCC has a lower inve...

  9. Economic assessment of novel amine based CO2 capture technologies integrated in power plants based on European Benchmarking Task Force methodology

    NARCIS (Netherlands)

    Manzolini, G.; Sanchez Fernandez, E.; Rezvani, S.; Macchi, E.; Goetheer, E.L.V.; Vlugt, T.J.H.

    2015-01-01

    The objective of this paper is to assess the economic advantages of an innovative solvent for CO2 capture on state-of-the-art solvents. The CESAR-1 solvent, which is an aqueous solution of 2-amino-2-methyl-propanol (AMP) and piperazine (PZ), is applied both to advanced supercritical pulverised (ASC)

  10. Competitiveness of CO2 capture from an industrial solid oxide fuel cell combined heat and power system in the early stage of market introduction

    NARCIS (Netherlands)

    Kuramochi, T.; Turkenburg, W.C.; Faaij, A.P.C.

    2011-01-01

    In this article, it was investigated whether potentially low-cost CO2 capture from SOFC systems could enhance the penetration of SOFC in the energy market in a highly carbon-constrained society in the mid-term future (up to year 2025). The application of 5 MWe SOFC systems for industrial combined

  11. Competitiveness of CO2 capture from an industrial solid oxide fuel cell combined heat and power system in the early stage of market introduction

    NARCIS (Netherlands)

    Kuramochi, T.; Turkenburg, W.C.; Faaij, A.P.C.

    2011-01-01

    In this article, it was investigated whether potentially low-cost CO2 capture from SOFC systems could enhance the penetration of SOFC in the energy market in a highly carbon-constrained society in the mid-term future (up to year 2025). The application of 5 MWe SOFC systems for industrial combined he

  12. Economic assessment of novel amine based CO2 capture technologies integrated in power plants based on European Benchmarking Task Force methodology

    NARCIS (Netherlands)

    Manzolini, G.; Sanchez Fernandez, E.; Rezvani, S.; Macchi, E.; Goetheer, E.L.V.; Vlugt, T.J.H.

    2015-01-01

    The objective of this paper is to assess the economic advantages of an innovative solvent for CO2 capture on state-of-the-art solvents. The CESAR-1 solvent, which is an aqueous solution of 2-amino-2-methyl-propanol (AMP) and piperazine (PZ), is applied both to advanced supercritical pulverised (ASC)

  13. The potential role of natural gas power plants with carbon capture and storage as a bridge to a low-carbon future

    Science.gov (United States)

    The CO2 intensity of electricity produced by state-of-the-art natural gas combined-cycle turbines (NGCC) is approximately one-third that of the U.S. fleet of existing coal plants. Compared to new nuclear plants and coal plants with integrated carbon capture, NGCC has a lower inve...

  14. Improving the training process of power sports athletes based on their biorhythms

    Directory of Open Access Journals (Sweden)

    Oleksandr Piven

    2014-10-01

    Full Text Available Purpose: improved methods of planning the training process for strength sports athletes with regard to their biorhythms. Material and Methods: the study included 16 athletes qualified yaks were members of the team of the Kharkiv region in weightlifting and powerlifting. Results: revealed that the experimental group athletes who used to planned training load calculations biorhythms improved power rates by 7,2% in compare with the control group who exercised without calculating biorhythms improved results on the power – 4,6%. It was also shown that athletes are more or less manifest Biorhythmic dependence. Conclusions: it was established that the planning of the training process, taking into account jet lag has a positive effect on the result of more than planning the same load without jet lag.

  15. Opening of the first CO{sub 2} capture installation on the fumes of a coal power plant - european project Castor, Denmark; Inauguration de la premiere installation de captage du CO{sub 2} sur les fumees d'une centrale electrique au charbon - Projet europeen Castor, Danemark

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-03-15

    The 15 March 2006, was launched the first industrial pilot of CO{sub 2} capture of the Castor project, coordinated by the IFP and financed by the european commission, on the site of the Esbjerg (Denmark) power plant. It is the first world installation allowing the CO{sub 2} capture on the fumes of a coal power plant. This document presents the pilot installation, discusses the european project Castor, the advantages of the CO{sub 2} capture and storage for a better use of the fossil energies, where and how capturing the CO{sub 2} and the Denmark energy context. (A.L.B.)

  16. Low-Power Adiabatic Computing with Improved Quasistatic Energy Recovery Logic

    Directory of Open Access Journals (Sweden)

    Shipra Upadhyay

    2013-01-01

    Full Text Available Efficiency of adiabatic logic circuits is determined by the adiabatic and non-adiabatic losses incurred by them during the charging and recovery operations. The lesser will be these losses circuit will be more energy efficient. In this paper, a new approach is presented for minimizing power consumption in quasistatic energy recovery logic (QSERL circuit which involves optimization by removing the nonadiabatic losses completely by replacing the diodes with MOSFETs whose gates are controlled by power clocks. Proposed circuit inherits the advantages of quasistatic ERL (QSERL family but is with improved power efficiency and driving ability. In order to demonstrate workability of the newly developed circuit, a 4 × 4 bit array multiplier circuit has been designed. A mathematical expression to calculate energy dissipation in proposed inverter is developed. Performance of the proposed logic (improved quasistatic energy recovery logic (IQSERL is analyzed and compared with CMOS and reported QSERL in their representative inverters and multipliers in VIRTUOSO SPECTRE simulator of Cadence in 0.18 μm UMC technology. In our proposed (IQSERL inverter the power efficiency has been improved to almost 20% up to 50 MHz and 300 fF external load capacitance in comparison to CMOS and QSERL circuits.

  17. Final Report on the Operation and Maintenance Improvement Program for Concentrating Solar Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Cohen Gilbert E.; Kearney, David W.; Kolb, Gregory J.

    1999-06-01

    This report describes the results of a six-year, $6.3 million project to reduce operation and maintenance (O&M) costs at power plants employing concentrating solar power (CSP) technology. Sandia National Laboratories teamed with KJC Operating Company to implement the O&M Improvement Program. O&M technologies developed during the course of the program were demonstrated at the 150-MW Kramer Junction solar power park located in Boron, California. Improvements were made in the following areas: (a) efficiency of solar energy collection, (b) O&M information management, (c) reliability of solar field flow loop hardware, (d) plant operating strategy, and (e) cost reduction associated with environmental issues. A 37% reduction in annual O&M costs was achieved. Based on the lessons learned, an optimum solar- field O&M plan for future CSP plants is presented. Parabolic trough solar technology is employed at Kramer Junction. However, many of the O&M improvements described in the report are also applicable to CSP plants based on solar power tower or dish/engine concepts.

  18. Repetitive transcranial magnetic stimulation improves consciousness disturbance in stroke patients A quantitative electroencephalography spectral power analysis

    Institute of Scientific and Technical Information of China (English)

    Ying Xie; Tong Zhang

    2012-01-01

    Repetitive transcranial magnetic stimulation is a noninvasive treatment technique that can directly alter cortical excitability and improve cerebral functional activity in unconscious patients. To investigate the effects and the electrophysiological changes of repetitive transcranial magnetic stimulation cortical treatment, 10 stroke patients with non-severe brainstem lesions and with disturbance of consciousness were treated with repetitive transcranial magnetic stimulation. A quantitative electroencephalography spectral power analysis was also performed. The absolute power in the alpha band was increased immediately after the first repetitive transcranial magnetic stimulation treatment, and the energy was reduced in the delta band. The alpha band relative power values slightly decreased at 1 day post-treatment, then increased and reached a stable level at 2 weeks post-treatment. Glasgow Coma Score and JFK Coma Recovery Scale-Revised score were improved. Relative power value in the alpha band was positively related to Glasgow Coma Score and JFK Coma Recovery Scale-Revised score. These data suggest that repetitive transcranial magnetic stimulation is a noninvasive, safe, and effective treatment technology for improving brain functional activity and promoting awakening in unconscious stroke patients.

  19. Efficiency improvement of power-to-gas technology by biogas upgrading; Effizienzsteigerung von Power-to-Gas-Technologie durch Biogasaufbereitung

    Energy Technology Data Exchange (ETDEWEB)

    Wuensche, Karsten [MT-BioMethan GmbH, Zeven (Germany)

    2013-08-15

    As a result of the accelerated turnaround in energy policy and Germany's complete nuclear phase-out by the end of 2022 there is a need for a radical transformation of the energy supply. In the conflicting areas of renewable energies expansion, network infrastructure with limited feed-in capacity, focussed centres of energy generation and fluctuations in demand, the discussion around implementation is controversial. A promising solution is the power-to-gas concept with which surplus electricity from wind energy can be transformed into synthetic natural gas. The combination of this process with biogas technology offers great potential for efficiency improvement. The upgrading of raw biogas to biomethane by pressureless amine scrubbing involves relevant synergy effects that can be exploited in terms of heat and carbon dioxide. (orig.)

  20. Development and fabrication of improved power transistor switches. [fabrication and manufacturing of semiconductor devices

    Science.gov (United States)

    Hower, P. L.; Chu, C. K.

    1976-01-01

    A new class of high-voltage power transistors has been achieved by adapting present interdigitated thyristor processing techniques to the fabrication of NPN Si transistors. Present devices are 2.3 cm in diameter. The electrical performance obtained is consistent with the predictions of an optimum design theory specifically developed for power switching transistors. The forward safe operating area of the experimental transistors shows a significant improvement over commercially available devices. The report describes device design, wafer processing, and various measurements which include dc characteristics, forward and reverse second breakdown limits, and switching times.