Biosurfactants for microbubble preparation and application

Science.gov (United States)

Biosurfactants can be classified by their chemical composition and their origin. This review briefly describes the type of biosurfactants based on their origin. Some of the widely used biosurfactants are introduced. The current statues and future trends in the production of biosurfactants are discus...

Isolation of biosurfactant producers, optimization and properties of biosurfactant produced by Acinetobacter sp. from petroleum-contaminated soil.

Science.gov (United States)

Chen, J; Huang, P T; Zhang, K Y; Ding, F R

2012-04-01

To screen and identify biosurfactant producers from petroleum-contaminated soil; to use response surface methodology (RSM) for medium optimization to enhance biosurfactant production; and to study the properties of the newly obtained biosurfactant towards pH, temperature and salinity. We successfully isolated three biosurfactant producers from petroleum-contaminated soil and identified them through 16S rRNA sequence analysis, which exhibit the highest similarities to Acinetobacter beijerinckii (100%), Kocuria marina (99%) and Kineococcus marinus (99%), respectively. A quadratic response model was constructed through RSM designs, leading to a 57·5% increase of the growth-associated biosurfactant production by Acinetobacter sp. YC-X 2 with an optimized medium: beef extract 3·12 g l(-1) ; peptone 20·87 g l(-1) ; NaCl 1·04 g l(-1); and n-hexadecane 1·86 g l(-1). Biosurfactant produced by Acinetobacter sp. YC-X 2 retained its properties during exposure to a wide range of pH values (5-11), high temperatures (up to 121°C) and high salinities [up to 18% (w/v) Na(+) and Ca(2+) ], which was more sensitive to Ca(2+) than Na(+). Two novel biosurfactant producers were isolated from petroleum-contaminated soil. Biosurfactant from Acinetobacter sp. YC-X 2 has good properties to a wide range of pH, high temperature and high salinity, and its production was optimized successfully through RSM. The fact, an increasing demand of high-quality surfactants and the lack of cost-competitive bioprocesses of biosurfactants for commercial utilization, motivates researchers to develop cost-effective strategies for biosurfactant production through isolating new biosurfactant producers with special surface-active properties and optimizing their cultural conditions. Two novel biosurfactant producers in this study will widen our knowledge about this kind of micro-organism. This work is the first application of RSM designs for cultural optimization of biosurfactant produced by Acinetobacter

Assessing Bacillus subtilis biosurfactant effects on the biodegradation of petroleum products.

Science.gov (United States)

Montagnolli, Renato Nallin; Lopes, Paulo Renato Matos; Bidoia, Ederio Dino

2015-01-01

Microbial pollutant removal capabilities can be determined and exploited to accomplish bioremediation of hydrocarbon-polluted environments. Thus, increasing knowledge on environmental behavior of different petroleum products can lead to better bioremediation strategies. Biodegradation can be enhanced by adding biosurfactants to hydrocarbon-degrading microorganism consortia. This work aimed to improve petroleum products biodegradation by using a biosurfactant produced by Bacillus subtilis. The produced biosurfactant was added to biodegradation assays containing crude oil, diesel, and kerosene. Biodegradation was monitored by a respirometric technique capable of evaluating CO₂ production in an aerobic simulated wastewater environment. The biosurfactant yielded optimal surface tension reduction (30.9 mN m(-1)) and emulsification results (46.90% with kerosene). Biodegradation successfully occurred and different profiles were observed for each substance. Precise mathematical modeling of biosurfactant effects on petroleum degradation profile was designed, hence allowing long-term kinetics prediction. Assays containing biosurfactant yielded a higher overall CO₂ output. Higher emulsification and an enhanced CO2 production dataset on assays containing biosurfactants was observed, especially in crude oil and kerosene.

Biosurfactants during in situ bioremediation: factors that influence the production and challenges in evalution.

Science.gov (United States)

Decesaro, Andressa; Machado, Thaís Strieder; Cappellaro, Ângela Carolina; Reinehr, Christian Oliveira; Thomé, Antônio; Colla, Luciane Maria

2017-09-01

Research on the influence of biosurfactants on the efficiency of in situ bioremediation of contaminated soil is continuously growing. Despite the constant progress in understanding the mechanisms involved in the effects of biosurfactants, there are still many factors that are not sufficiently elucidated. There is a lack of research on autochthonous or exogenous microbial metabolism when biostimulation or bioaugmentation is carried out to produce biosurfactants at contaminated sites. In addition, studies on the application of techniques that measure the biosurfactants produced in situ are needed. This is important because, although the positive influence of biosurfactants is often reported, there are also studies where no effect or negative effects have been observed. This review aimed to examine some studies on factors that can improve the production of biosurfactants in soils during in situ bioremediation. Moreover, this work reviews the methodologies that can be used for measuring the production of these biocomposts. We reviewed studies on the potential of biosurfactants to improve the bioremediation of hydrocarbons, as well as the limitations of methods for the production of these biomolecules by microorganisms in soil.

Biodegradation of diesel oil by a novel microbial consortium: comparison between co-inoculation with biosurfactant-producing strain and exogenously added biosurfactants.

Science.gov (United States)

Mnif, Inès; Mnif, Sami; Sahnoun, Rihab; Maktouf, Sameh; Ayedi, Younes; Ellouze-Chaabouni, Semia; Ghribi, Dhouha

2015-10-01

Bioremediation, involving the use of microorganisms to detoxify or remove pollutants, is the most interesting strategy for hydrocarbon remediation. In this aim, four hydrocarbon-degrading bacteria were isolated from oil-contaminated soil in Tunisia. They were identified by the 16S rDNA sequence analysis, as Lysinibacillus bronitolerans RI18 (KF964487), Bacillus thuringiensis RI16 (KM111604), Bacillus weihenstephanensis RI12 (KM094930), and Acinetobacter radioresistens RI7 (KJ829530). Moreover, a lipopeptide biosurfactant produced by Bacillus subtilis SPB1, confirmed to increase diesel solubility, was tested to increase diesel biodegradation along with co-inoculation with two biosurfactant-producing strains. Culture studies revealed the enhancement of diesel biodegradation by the selected consortium with the addition of SPB1 lipopeptide and in the cases of co-inoculation by biosurfactant-producing strain. In fact, an improvement of about 38.42 and 49.65 % of diesel degradation was registered in the presence of 0.1 % lipopeptide biosurfactant and when culturing B. subtilis SPB1 strain with the isolated consortium, respectively. Furthermore, the best improvement, evaluated to about 55.4 %, was recorded when using the consortium cultured with B. subtilis SPB1 and A. radioresistens RI7 strains. Gas chromatography analyses were correlated with the gravimetric evaluation of the residual hydrocarbons. Results suggested the potential applicability of the selected consortium along with the ex situ- and in situ-added biosurfactant for the effective bioremediation of diesel-contaminated water and soil.

Improved bioavailability and biodegradation of a model polyaromatic hydrocarbon by a biosurfactant producing bacterium of marine origin.

Science.gov (United States)

Das, Palashpriya; Mukherjee, Soumen; Sen, Ramkrishna

2008-07-01

Polyaromatic hydrocarbons (PAHs) are organic pollutants mostly derived from the processing and combustion of fossil fuels and cause human health hazards. In the present study a marine biosurfactant producing strain of Bacillus circulans was used to increase the bioavailability and consequent degradation of a model polyaromatic hydrocarbon, anthracene. Although the organism could not utilize anthracene as the sole carbon source, it showed better growth and biosurfactant production in an anthracene supplemented glycerol mineral salts medium (AGlyMSM) compared to a normal glycerol mineral salts medium (GlyMSM). The biosurfactant product showed high degree of emulsification of various hydrocarbons. Analysis by gas chromatography (GC), high performance thin layer chromatography (HPTLC) and Fourier transform infrared spectroscopy (FTIR) showed that the biosurfactant could effectively entrap and solubilize PAH. Thin layer chromatographic analysis showed that anthracene was utilized as a carbon substrate for the production of biosurfactant. Thus organic pollutant anthracene was metabolized and converted to biosurfactants facilitating its own bioremediation.

Environmental applications of biosurfactants: recent advances.

Science.gov (United States)

Pacwa-Płociniczak, Magdalena; Płaza, Grażyna A; Piotrowska-Seget, Zofia; Cameotra, Swaranjit Singh

2011-01-18

Increasing public awareness of environmental pollution influences the search and development of technologies that help in clean up of organic and inorganic contaminants such as hydrocarbons and metals. An alternative and eco-friendly method of remediation technology of environments contaminated with these pollutants is the use of biosurfactants and biosurfactant-producing microorganisms. The diversity of biosurfactants makes them an attractive group of compounds for potential use in a wide variety of industrial and biotechnological applications. The purpose of this review is to provide a comprehensive overview of advances in the applications of biosurfactants and biosurfactant-producing microorganisms in hydrocarbon and metal remediation technologies.

Kinetics of hydrocarbon extraction from oil shale using biosurfactant producing bacteria

International Nuclear Information System (INIS)

Haddadin, Malik S.Y.; Abou Arqoub, Ansam A.; Abu Reesh, Ibrahim; Haddadin, Jamal

2009-01-01

This study was done to extract hydrocarbon compounds from El-Lajjun oil shale using biosurfactant produced from two strains Rhodococcus erythropolis and Rhodococcus ruber. The results have shown that, optimal biosurfactant production was found using naphthalene and diesel as a carbon source for R. erthropolis and R. ruber, respectively. Optimum nitrogen concentration was 9 g/l and 7 g/l for R. erthropolis and R. ruber, respectively. Optimum K 2 HPO 4 to KH 2 PO 4 ratio, temperature, pH, and agitation speeds were 2:1, 37 deg. C, 7 and 200 rpm. Under optimal conditions R. erthropolis and R. ruber produced 5.67 and 6.9 g/l biosurfactant, respectively. Maximum recovery of oil achieved with hydrogen peroxide pre-treatment was 25% and 26% at biosurfactant concentration of 8 g/l and 4 g/l for R. erthropolis and R. ruber, respectively. The extent desorption of hydrocarbons from the pre-treated oil shale by biosurfactant were inversely related to the concentration of high molecular weight hydrocarbons, asphaltenes compounds. Pre- treatment of oil shale with hydrogen peroxide produced better improvement in aromatic compounds extraction in comparison with improvement which resulted from demineralization of the oil shale

Biosurfactants and their role in oil recovery

Energy Technology Data Exchange (ETDEWEB)

McInerney, Michael J. [University of Oklahoma (United States)

2011-07-01

This paper presents the role of biosurfactants in oil recovery. Types of biosurfactants include, among others, lipopeptides, rhamnolipids, sophorolipids. The process of oil recovery and the involvement of microbes are explained. The objective is to know if lipopeptide biosurfactants lower interfacial tension. Fatty acid composition is important for lipopeptide biosurfactant activity and microbial surfactants are hydrophilic and Interfacial Tension (IFT) values are high. Examples of biosurfactants with lower IFT values with mixtures are also given. An experiment was conducted to determine whether lipopeptides recovery entrapped oil or not. The procedure and experimental setup are shown. It is seen that with higher concentration of biosurfactants, the percentage of residual oil recovery is higher. Another experiment was conducted to see if biosurfactants greater than 40 mg/l can be produced in oil reservoirs. The experimental design and the analysis with the results are given. It was seen that more oil was produced. Conclusions from the study were, among other findings, that, in situ biosurfactant production and inoculation are possible.

Detection of biosurfactants in Bacillus species: genes and products identification.

Science.gov (United States)

Płaza, G; Chojniak, J; Rudnicka, K; Paraszkiewicz, K; Bernat, P

2015-10-01

To screen environmental Bacillus strains for detection of genes encoding the enzymes involved in biosurfactant synthesis and to evaluate their products e.g. surfactin, iturin and fengycin. The taxonomic identification of isolated from the environment Bacillus strains was performed by Microgene ID Bacillus panel and GEN III Biolog system. The polymerase chain reaction (PCR) strategy for screening of genes in Bacillus strains was set up. Liquid chromatography-mass spectrometry (LC-MS/MS) method was used for the identification of lipopeptides (LPs). All studied strains exhibited the presence of srfAA gene and produced surfactin mostly as four homologues (C13 to C16). Moreover, in 2 strains (KP7, T'-1) simultaneous co-production of 3 biosurfactants: surfactin, iturin and fengycin was observed. Additionally, it was found out that isolate identified as Bacillus subtilis ssp. subtilis (KP7), beside LPs co-production, synthesizes surfactin with the efficiency much higher than other studied strains (40·2 mg l(-1) ) and with the yield ranging from 0·8 to 8·3 mg l(-1) . We showed that the combined methodology based on PCR and LC-MS/MS technique is an optimal tool for the detection of genes encoding enzymes involved in biosurfactant synthesis as well as their products, e.g. surfactin, iturin and fengycin. This approach improves the screening and the identification of environmental Bacillus co-producing biosurfactants-stimulating and facilitating the development of this area of science. The findings of this work will help to improve screening of biosurfactant producers. Discovery of novel biosurfactants and biosurfactants co-production ability has shed light on their new application fields and for the understanding of their interactions and properties. © 2015 The Society for Applied Microbiology.

Environmental Applications of Biosurfactants: Recent Advances

Directory of Open Access Journals (Sweden)

Swaranjit Singh Cameotra

2011-01-01

Full Text Available Increasing public awareness of environmental pollution influences the search and development of technologies that help in clean up of organic and inorganic contaminants such as hydrocarbons and metals. An alternative and eco-friendly method of remediation technology of environments contaminated with these pollutants is the use of biosurfactants and biosurfactant-producing microorganisms. The diversity of biosurfactants makes them an attractive group of compounds for potential use in a wide variety of industrial and biotechnological applications. The purpose of this review is to provide a comprehensive overview of advances in the applications of biosurfactants and biosurfactant-producing microorganisms in hydrocarbon and metal remediation technologies.

Biosurfactants for Microbubble Preparation and Application

OpenAIRE

Takeo Shiina; Zengshe Liu; Mitsutoshi Nakajima; Qingyi Xu

2011-01-01

Biosurfactants can be classified by their chemical composition and their origin. This review briefly describes various classes of biosurfactants based on their origin and introduces a few of the most widely used biosurfactants. The current status and future trends in biosurfactant production are discussed, with an emphasis on those derived from plants. Following a brief introduction of the properties of microbubbles, recent progress in the application of microbubble technology to molecular im...

Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances

Directory of Open Access Journals (Sweden)

DARNE GERMANO DE ALMEIDA

2016-10-01

Full Text Available The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulphate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernise petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries.

Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances.

Science.gov (United States)

De Almeida, Darne G; Soares Da Silva, Rita de Cássia F; Luna, Juliana M; Rufino, Raquel D; Santos, Valdemir A; Banat, Ibrahim M; Sarubbo, Leonie A

2016-01-01

The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning, and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulfate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands, and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernize petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries.

Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances

Science.gov (United States)

De Almeida, Darne G.; Soares Da Silva, Rita de Cássia F.; Luna, Juliana M.; Rufino, Raquel D.; Santos, Valdemir A.; Banat, Ibrahim M.; Sarubbo, Leonie A.

2016-01-01

The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning, and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulfate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands, and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernize petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries. PMID:27843439

Kinetics of hydrocarbon extraction from oil shale using biosurfactant producing bacteria

Energy Technology Data Exchange (ETDEWEB)

Haddadin, Malik S.Y.; Abou Arqoub, Ansam A.; Abu Reesh, Ibrahim [Faculty of Graduate Studies, Jordan University, Queen Rania Street, Amman, 11942 (Jordan); Haddadin, Jamal [Faculty of Agriculture, Mutah University, P.O. Box 59, Mutah 61710 (Jordan)

2009-04-15

This study was done to extract hydrocarbon compounds from El-Lajjun oil shale using biosurfactant produced from two strains Rhodococcus erythropolis and Rhodococcus ruber. The results have shown that, optimal biosurfactant production was found using naphthalene and diesel as a carbon source for R. erthropolis and R. ruber, respectively. Optimum nitrogen concentration was 9 g/l and 7 g/l for R. erthropolis and R. ruber, respectively. Optimum K{sub 2}HPO{sub 4} to KH{sub 2}PO{sub 4} ratio, temperature, pH, and agitation speeds were 2:1, 37 C, 7 and 200 rpm. Under optimal conditions R. erthropolis and R. ruber produced 5.67 and 6.9 g/l biosurfactant, respectively. Maximum recovery of oil achieved with hydrogen peroxide pre-treatment was 25% and 26% at biosurfactant concentration of 8 g/l and 4 g/l for R. erthropolis and R. ruber, respectively. The extent desorption of hydrocarbons from the pre-treated oil shale by biosurfactant were inversely related to the concentration of high molecular weight hydrocarbons, asphaltenes compounds. Pre-treatment of oil shale with hydrogen peroxide produced better improvement in aromatic compounds extraction in comparison with improvement which resulted from demineralization of the oil shale. (author)

Improved Biosurfactant Production by Bacillus subtilis SPB1 Mutant Obtained by Random Mutagenesis and Its Application in Enhanced Oil Recovery in a Sand System.

Science.gov (United States)

Bouassida, Mouna; Ghazala, Imen; Ellouze-Chaabouni, Semia; Ghribi, Dhouha

2018-01-28

Biosurfactants or microbial surfactants are surface-active biomolecules that are produced by a variety of microorganisms. Biodegradability and low toxicity have led to the intensification of scientific studies on a wide range of industrial applications for biosurfactants in the field of environmental bioremediation as well as the petroleum industry and enhanced oil recovery. However, the major issues in biosurfactant production are high production cost and low yield. Improving the bioindustrial production processes relies on many strategies, such as the use of cheap raw materials, the optimization of medium-culture conditions, and selecting hyperproducing strains. The present work aims to obtain a mutant with higher biosurfactant production through applying mutagenesis on Bacillus subtilis SPB1 using a combination of UV irradiation and nitrous acid treatment. Following mutagenesis and screening on blood agar and subsequent formation of halos, the mutated strains were examined for emulsifying activity of their culture broth. A mutant designated B. subtilis M2 was selected as it produced biosurfactant at twice higher concentration than the parent strain. The potential of this biosurfactant for industrial uses was shown by studying its stability to environmental stresses such as pH and temperature and its applicability in the oil recovery process. It was practically stable at high temperature and at a wide range of pH, and it recovered above 90% of motor oil adsorbed to a sand sample.

Production and Biomedical Applications of Probiotic Biosurfactants.

Science.gov (United States)

Fariq, Anila; Saeed, Ayesha

2016-04-01

Biosurfactants have been widely used for environmental and industrial applications. However, their use in medical field is still limited. Probiotic biosurfactants possess an immense antimicrobial, anti-adhesive, antitumor, and antibiofilm potential. Moreover, they have an additional advantage over conventional microbial surfactants because probiotics are an integral part of normal human microflora and their biosurfactants are innocuous to human. So, they can be effectively exploited for medicinal use. Present review is aimed to discourse the production and biomedical applications of probiotic biosurfactants.

Optimization and characterization of biosurfactant production from marine Vibrio sp. strain 3B-2

Science.gov (United States)

Hu, Xiaoke; Wang, Caixia; Wang, Peng

2015-01-01

A biosurfactant-producing bacterium, designated 3B-2, was isolated from marine sediment and identified as Vibrio sp. by 16S rRNA gene sequencing. The culture medium composition was optimized to increase the capability of 3B-2 for producing biosurfactant. The produced biosurfactant was characterized in terms of protein concentration, surface tension, and oil-displacement efficiency. The optimal medium for biosurfactant production contained: 0.5% lactose, 1.1% yeast extract, 2% sodium chloride, and 0.1% disodium hydrogen phosphate. Under optimal conditions (28°C), the surface tension of crude biosurfactant could be reduced to 41 from 71.5 mN/m (water), while its protein concentration was increased to up to 6.5 g/L and the oil displacement efficiency was improved dramatically at 6.5 cm. Two glycoprotein fractions with the molecular masses of 22 and 40 kDa were purified from the biosurfactant, which held great potential for applications in microbial enhanced oil recovery and bioremediation. PMID:26441908

Pseudomonas Lipopeptide Biosurfactants

DEFF Research Database (Denmark)

Bonnichsen, Lise

Pseudomonas lipopetide biosurfactants are amphiphilic molecules with a broad range of natural functions. Due to their surface active properties, it has been suggested that Pseudomonas lipopetides potentially play a role in biodegradation of hydrophobic compounds and have essential functions...... lipopetide biosurfactants in pollutant biodegradation and natural roles in biofilm formation. The work presented is a combination of environmental microbiology and exploiting genetic manipulation of pure cultures to achieve insightinto the effects and mechanisms of lipopeptides on microbial processes...

Biosurfactants in cosmetic formulations: trends and challenges.

Science.gov (United States)

Vecino, X; Cruz, J M; Moldes, A B; Rodrigues, L R

2017-11-01

Cosmetic products play an essential role in everyone's life. People everyday use a large variety of cosmetic products such as soap, shampoo, toothpaste, deodorant, skin care, perfume, make-up, among others. The cosmetic industry encompasses several environmental, social and economic impacts that are being addressed through the search for more efficient manufacturing techniques, the reduction of waste and emissions and the promotion of personal hygiene, contributing to an improvement of public health and at the same time providing employment opportunities. The current trend among consumers is the pursuit for natural ingredients in cosmetic products, as many of these products exhibit equal, better or additional benefits in comparison with the chemical-based products. In this sense, biosurfactants are natural compounds with great potential in the formulation of cosmetic products given by their biodegradability and impact in health. Indeed, many of these biosurfactants could exhibit a "prebiotic" character. This review covers the current state-of-the-art of biosurfactant research for cosmetic purposes and further discusses the future challenges for cosmetic applications.

Contributions of biosurfactants to natural or induced bioremediation.

Science.gov (United States)

Lawniczak, Lukasz; Marecik, Roman; Chrzanowski, Lukasz

2013-03-01

The number of studies dedicated to evaluating the influence of biosurfactants on bioremediation efficiency is constantly growing. Although significant progress regarding the explanation of mechanisms behind biosurfactant-induced effects could be observed, there are still many factors which are not sufficiently elucidated. This corresponds to the fact that although positive influence of biosurfactants is often reported, there are also numerous cases where no or negative effect was observed. This review summarizes the recent finding in the field of biosurfactant-amended bioremediation, focusing mainly on a critical approach towards potential limitations and causes of failure while investigating the effects of biosurfactants on the efficiency of biodegradation and phytoextraction processes. It also provides a summary of successive steps, which should be taken into consideration when designing biosurfactant-related treatment processes.

Crude oil biodegradation aided by biosurfactants from Pseudozyma sp. NII 08165 or its culture broth.

Science.gov (United States)

Sajna, Kuttuvan Valappil; Sukumaran, Rajeev Kumar; Gottumukkala, Lalitha Devi; Pandey, Ashok

2015-09-01

The aim of this work was to evaluate the biosurfactants produced by the yeast Pseudozyma sp. NII 08165 for enhancing the degradation of crude oil by a model hydrocarbon degrading strain, Pseudomonas putida MTCC 1194. Pseudozyma biosurfactants were supplemented at various concentrations to the P. putida culture medium containing crude oil as sole carbon source. Supplementation of the biosurfactants enhanced the degradation of crude oil by P. putida; the maximum degradation of hydrocarbons was observed with a 2.5 mg L(-1) supplementation of biosurfactants. Growth inhibition constant of the Pseudozyma biosurfactants was 11.07 mg L(-1). It was interesting to note that Pseudozyma sp. NII 08165 alone could also degrade diesel and kerosene. Culture broth of Pseudozyma containing biosurfactants resulted up to ∼46% improvement in degradation of C10-C24 alkanes by P. putida. The enhancement in degradation efficiency of the bacterium with the culture broth supplementation was even more pronounced than that with relatively purer biosurfactants. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biosurfactants from Acinetobacter calcoaceticus BU03 enhance the solubility and biodegradation of phenanthrene.

Science.gov (United States)

Zhao, Zhenyong; Wong, Jonathan W C

2009-03-01

A thermophilic bacterial strain, Acinetobacter calcoaceticus BU03, with a biosurfactant-producing capability, was isolated from petroleum-contaminated soil with an improved procedure which employed the solubilization of polycyclic aromatic hydrocarbons (PAHs), i.e. naphthalene in agar plate, as a selection criterion. Crude biosurfactant was recovered from the culture of BU03 by extraction with n-hexane, and its properties were investigated. Biosurfactants from A. calcoaceticus BU03 constitute a thermo-stable mixture, composed of different agents with surface activities. At their critical micelle concentration (CMC) of 152.4 mg L(-1), the crude biosurfactants produced from A. calcoaceticus BU03 decreased the air-water surface tension to 38.4 mN m(-1). In thermophilic conditions, the emulsifying activity is 2.8 times that of Tween 80. The effects of the biosurfactants produced by A. calcoaceticus on the solubility and biodegradation of PAHs were investigated in batch systems. Biosurfactants produced by A. calcoaceticus BU03 at 25 times their CMC significantly increased the apparent aqueous solubility of phenanthrene (PHE), pyrene (PYR) and benzo(a)pyrene (B[a]P) to 54.3, 6.33 and 2.08 mg L(-1), respectively. In aqueous system, the biosurfactants at concentrations of 0.5 CMC and 1 CMC slightly enhanced the biodegradation of PHE by a consortium of PAH-degrading microrganisms. Results indicate that biosurfactants from A. calcoaceticus BU03 have potential to enhance the removal of PAHs from contaminated sites.

Production and Structural Characterization of Lactobacillus helveticus Derived Biosurfactant

Science.gov (United States)

Sharma, Deepansh; Saharan, Baljeet Singh; Chauhan, Nikhil; Bansal, Anshul; Procha, Suresh

2014-01-01

A probiotic strain of lactobacilli was isolated from traditional soft Churpi cheese of Yak milk and found positive for biosurfactant production. Lactobacilli reduced the surface tension of phosphate buffer saline (PBS) from 72.0 to 39.5 mNm−1 pH 7.2 and its critical micelle concentration (CMC) was found to be 2.5 mg mL−1. Low cost production of Lactobacilli derived biosurfactant was carried out at lab scale fermenter which yields 0.8 mg mL−1 biosurfactant. The biosurfactant was found least phytotoxic and cytotoxic as compared to the rhamnolipid and sodium dodecyl sulphate (SDS) at different concentration. Structural attributes of biosurfactant were determined by FTIR, NMR (1H and 13C), UPLC-MS, and fatty acid analysis by GCMS which confirmed the presence of glycolipid type of biosurfactant closely similar to xylolipids. Biosurfactant is mainly constituted by lipid and sugar fractions. The present study outcomes provide valuable information on structural characterization of the biosurfactant produced by L. helveticus MRTL91. These findings are encouraging for the application of Lactobacilli derived biosurfactant as nontoxic surface active agents in the emerging field of biomedical applications. PMID:25506070

Alternative methodology for isolation of biosurfactant-producing bacteria.

Science.gov (United States)

Krepsky, N; Da Silva, F S; Fontana, L F; Crapez, M A C

2007-02-01

Wide biosurfactant application on biorremediation is limited by its high production cost. The search for cheaper biossurfactant production alternatives has guided our study. The use of selective media containing sucrose (10 g x L(-1)) and Arabian Light oil (2 g x L(-1)) as carbon sources showed to be effective to screen and maintain biosurfactant-producing consortia isolated from mangrove hydrocarbon-contaminated sediment. The biosurfactant production was assayed by kerosene, gasoline and Arabian Light Emulsification activity and the bacterial growth curve was determined by bacterial quantification. The parameters analyzed for biosurfactant production were the growth curve, salinity concentration, flask shape and oxygenation. All bacteria consortia screened were able to emulsify the petroleum derivatives tested. Biosurfactant production increased according to the incubation time; however the type of emulsification (non-aqueous phase or aqueous phase) did not change with time but with the compound tested. The methodology was able to isolate biosurfactant-producing consortia from superficial mangrove sediment contaminated by petroleum hydrocarbons and was recommended for selection of biosurfactant producing bacteria in tropical countries with low financial resources.

Alternative methodology for isolation of biosurfactant-producing bacteria

Directory of Open Access Journals (Sweden)

N. Krepsky

Full Text Available Wide biosurfactant application on biorremediation is limited by its high production cost. The search for cheaper biossurfactant production alternatives has guided our study. The use of selective media containing sucrose (10 g.L-1 and Arabian Light oil (2 g.L-1 as carbon sources showed to be effective to screen and maintain biosurfactant-producing consortia isolated from mangrove hydrocarbon-contaminated sediment. The biosurfactant production was assayed by kerosene, gasoline and Arabian Light Emulsification activity and the bacterial growth curve was determined by bacterial quantification. The parameters analyzed for biosurfactant production were the growth curve, salinity concentration, flask shape and oxygenation. All bacteria consortia screened were able to emulsify the petroleum derivatives tested. Biosurfactant production increased according to the incubation time; however the type of emulsification (non-aqueous phase or aqueous phase did not change with time but with the compound tested. The methodology was able to isolate biosurfactant-producing consortia from superficial mangrove sediment contaminated by petroleum hydrocarbons and was recommended for selection of biosurfactant producing bacteria in tropical countries with low financial resources.

Potential application of cyclic lipopeptide biosurfactants produced by Bacillus subtilis strains in laundry detergent formulations.

Science.gov (United States)

Mukherjee, A K

2007-09-01

Crude cyclic lipopeptide (CLP) biosurfactants from two Bacillus subtilis strains (DM-03 and DM-04) were studied for their compatibility and stability with some locally available commercial laundry detergents. CLP biosurfactants from both B. subtilis strains were stable over the pH range of 7.0-12.0, and heating them at 80 degrees C for 60 min did not result in any loss of their surface-active property. Crude CLP biosurfactants showed good emulsion formation capability with vegetable oils, and demonstrated excellent compatibility and stability with all the tested laundry detergents. CLP biosurfactants from B. subtilis strains act additively with other components of the detergents to further improve the wash quality of detergents. The thermal resistance and extreme alkaline pH stability of B. subtilis CLP biosurfactants favour their inclusion in laundry detergent formulations. This study has great significance because it is already known that microbial biosurfactants are considered safer alternative to chemical or synthetic surfactants owing to lower toxicity, ease of biodegradability and low ecological impact. The present study provides further evidence that CLP biosurfactants from B. subtilis strains can be employed in laundry detergents.

Isolation of Biosurfactant Producing Bacteria from Oil Reservoirs

Directory of Open Access Journals (Sweden)

A Tabatabaee, M Mazaheri Assadi, AA Noohi,VA Sajadian

2005-01-01

Full Text Available Biosurfactants or surface-active compounds are produced by microoaganisms. These molecules reduce surface tension both aqueous solutions and hydrocarbon mixtures. In this study, isolation and identification of biosurfactant producing bacteria were assessed. The potential application of these bacteria in petroleum industry was investigated. Samples (crude oil were collected from oil wells and 45 strains were isolated. To confirm the ability of isolates in biosurfactant production, haemolysis test, emulsification test and measurement of surface tension were conducted. We also evaluated the effect of different pH, salinity concentrations, and temperatures on biosurfactant production. Among importance features of the isolated strains, one of the strains (NO.4: Bacillus.sp showed high salt tolerance and their successful production of biosurfactant in a vast pH and temperature domain and reduced surface tension to value below 40 mN/m. This strain is potential candidate for microbial enhanced oil recovery. The strain4 biosurfactant component was mainly glycolipid in nature.

Microbial biosurfactants: challenges and opportunities for future exploitation.

Science.gov (United States)

Marchant, Roger; Banat, Ibrahim M

2012-11-01

The drive for industrial sustainability has pushed biosurfactants to the top of the agenda of many companies. Biosurfactants offer the possibility of replacing chemical surfactants, produced from nonrenewable resources, with alternatives produced from cheap renewable feedstocks. Biosurfactants are also attractive because they are less damaging to the environment yet are robust enough for industrial use. The most promising biosurfactants at the present time are the glycolipids, sophorolipids produced by Candida yeasts, mannosylerythritol lipids (MELs) produced by Pseudozyma yeasts, and rhamnolipids produced by Pseudomonas. Despite the current enthusiasm for these compounds several residual problems remain. This review highlights remaining problems and indicates the prospects for imminent commercial exploitation of a new generation of microbial biosurfactants. Copyright © 2012 Elsevier Ltd. All rights reserved.

Biosurfactant-enhanced hydrogen production from organic fraction of municipal solid waste using co-culture of E. coli and Enterobacter aerogenes.

Science.gov (United States)

Sharma, Preeti; Melkania, Uma

2017-11-01

The effect of biosurfactants (surfactin and saponin) on the hydrogen production from organic fraction of municipal solid waste (OFMSW) was investigated using co-culture of facultative anaerobes Enterobacter aerogenes and E. coli. The biosurfactants were applied in the concentration ranges of 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5 and 5.0% each. Cumulative hydrogen production (P), maximum hydrogen production rate (Rmax) and lag phases (λ) were analyzed using modified Gompertz model. Results revealed that both the biosurfactants were effective in hydrogen production enhancement. The maximum cumulative hydrogen production of 743.5±14.4ml and 675.6±12.1ml and volumetric hydrogen production of 2.12L H2 /L substrate and 1.93L H2 /L substrate was recorded at 3.5% surfactin and 3.0% saponin respectively. Corresponding highest hydrogen yields were 79.2mlH 2 /gCarbo initial and 72.0mlH 2 /gCarbo initial respectively. Lag phase decreased from 12.5±2.0h at control to a minimum of 9.0±2.8h and 9.5±2.1h at 3.5% surfactin and 3.0% saponin respectively. Volatile fatty acid generation was increased with biosurfactants addition. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chemical characterization of carbohydrate-based biosurfactants

Science.gov (United States)

High-yield, glycolipid-based biosurfactants are of increasing interest for use in environmentally benign cleaning or emulsifying agents. We have developed a MALDI-TOF/MS screen for the rapid analysis of several types of biosurfactants, including various acylated rhamnolipids in Pseudomonas extracts...

Enhancement of Bacillus subtilis Lipopeptide Biosurfactants Production through Optimization of Medium Composition and Adequate Control of Aeration

OpenAIRE

Ghribi, Dhouha; Ellouze-Chaabouni, Semia

2011-01-01

Interest in biosurfactants has increased considerably in recent years, as they are potentially used in many commercial applications in petroleum, pharmaceuticals, biomedical, and food processing industries. Since improvement of their production was of great importance to reduce the final coast, cultural conditions were analyzed to optimize biosurfactants production from Bacillus subtilis SPB1 strain. A high yield of biosurfactants was obtained from a culture of B. subtilis using carbohydrate ...

Biosurfactants as green stabilizers for the biological synthesis of nanoparticles.

Science.gov (United States)

Kiran, G Seghal; Selvin, Joseph; Manilal, Aseer; Sujith, S

2011-12-01

Taking into consideration the needs of greener bioprocesses and novel enhancers for synthesis using microbial processes, biosurfactants, and/or biosurfactant producing microbes are emerging as an alternate source for the rapid synthesis of nanoparticles. A microemulsion technique using an oil-water-surfactant mixture was shown to be a promising approach for nanoparticle synthesis. Biosurfactants are natural surfactants derived from microbial origin composed mostly of sugar and fatty acid moieties, they have higher biodegradability, lower toxicity, and excellent biological activities. The biosurfactant mediated process and microbial synthesis of nanoparticles are now emerging as clean, nontoxic, and environmentally acceptable "green chemistry" procedures. The biosurfactant-mediated synthesis is superior to the methods of bacterial- or fungal-mediated nanoparticle synthesis, since biosurfactants reduce the formation of aggregates due to the electrostatic forces of attraction and facilitate a uniform morphology of the nanoparticles. In this review, we highlight the biosurfactant mediated synthesis of nanoparticles with relevant details including a greener bioprocess, sources of biosurfactants, and biological synthesized nanoparticles based on the available literature and laboratory findings.

Production of biosurfactants using substrates from renewable-resources

Directory of Open Access Journals (Sweden)

Suppasil Maneerat

2005-05-01

Full Text Available Surface-active compounds commonly used in industries are chemically synthesized. However, biosurfactants have been paid increasing attention to replace the synthetic surfactants owing to their advantages such as biodegradability and low toxicity. Nowadays, the use of biosurfactant has been limited due to the high production cost. Nevertheless, biosurfactants can be produced with high yield by some microorganisms, especially Pseudomonas sp. These microorganisms can use the various renewal resources, especially agroindustrial wastes, as the potential carbon sources. This leads to the greater possibility for economical biosurfactant production and reduced pollution caused by those wastes.

Effect of biosurfactant from two strains of Pseudomonas on ...

African Journals Online (AJOL)

Two Pseudomonas strains isolated from oil-contaminated soil which produce biosurfactant were studied. The biosurfactant containing broth formed stable emulsions with liquid light paraffin, cooking medium vegetable oil and toluene. The strains under study produce extra cellular biosurfactant in the culture media.

Biosurfactant production by Pseudomonas strains isolated from floral nectar.

Science.gov (United States)

Ben Belgacem, Z; Bijttebier, S; Verreth, C; Voorspoels, S; Van de Voorde, I; Aerts, G; Willems, K A; Jacquemyn, H; Ruyters, S; Lievens, B

2015-06-01

To screen and identify biosurfactant-producing Pseudomonas strains isolated from floral nectar; to characterize the produced biosurfactants; and to investigate the effect of different carbon sources on biosurfactant production. Four of eight nectar Pseudomonas isolates were found to produce biosurfactants. Phylogenetic analysis based on three housekeeping genes (16S rRNA gene, rpoB and gyrB) classified the isolates into two groups, including one group closely related to Pseudomonas fluorescens and another group closely related to Pseudomonas fragi and Pseudomonas jessenii. Although our nectar pseudomonads were able to grow on a variety of water-soluble and water-immiscible carbon sources, surface active agents were only produced when using vegetable oil as sole carbon source, including olive oil, sunflower oil or waste frying sunflower oil. Structural characterization based on thin layer chromatography (TLC) and ultra high performance liquid chromatography-accurate mass mass spectrometry (UHPLC-amMS) revealed that biosurfactant activity was most probably due to the production of fatty acids (C16:0; C18:0; C18:1 and C18:2), and mono- and diglycerides thereof. Four biosurfactant-producing nectar pseudomonads were identified. The active compounds were identified as fatty acids (C16:0; C18:0; C18:1 and C18:2), and mono- and diglycerides thereof, produced by hydrolysis of triglycerides of the feedstock. Studies on biosurfactant-producing micro-organisms have mainly focused on microbes isolated from soils and aquatic environments. Here, for the first time, nectar environments were screened as a novel source for biosurfactant producers. As nectars represent harsh environments with high osmotic pressure and varying pH levels, further screening of nectar habitats for biosurfactant-producing microbes may lead to the discovery of novel biosurfactants with broad tolerance towards different environmental conditions. © 2015 The Society for Applied Microbiology.

Biosurfactant-enhanced bioremediation of hydrophobic pollutants

Energy Technology Data Exchange (ETDEWEB)

Cameotra, S.S.; Makkar, R.S. [Inst. of Microbial Technology, Chandigarh (India)

2010-01-15

Biosurfactants are surface-active compounds synthesized by a wide variety of microorganisms. They are molecules that have both hydrophobic and - philic domains and are capable of lowering the surface tension and the interfacial tension of the growth medium. Biosurfactants possess different chemical structures-lipopeptides, glycolipids, neutral lipids, and fatty acids. They are nontoxic biomolecules that are biodegradable. Biosurfactants also exhibit strong emulsification of hydrophobic compounds and form stable emulsions. Polycyclic aromatic hydrocarbons (PAHs), crude on sludge, and pesticides call be toxic, mutagenic, and carcinogenic compounds that pollute the environment. They are released into the environment as a result of oil spillage and by-products of coal treatment processes. The low water solubility of these compounds limits their availability to microorganisms, which is a potential problem for bioremediation of contaminated sites. Microbially produced surfactants enhance the bioavailability of these hydrophobic compounds for bioremediation. Therefore, biosurfactant-enhanced solubility of pollutants has potential hioremediation applications.

Biosurfactant-producing bacterium, Pseudomonas aeruginosa MA01 isolated from spoiled apples: physicochemical and structural characteristics of isolated biosurfactant.

Science.gov (United States)

Abbasi, Habib; Hamedi, Mir Manochehr; Lotfabad, Tayebe Bagheri; Zahiri, Hossein Shahbani; Sharafi, Hakimeh; Masoomi, Fatemeh; Moosavi-Movahedi, Ali Akbar; Ortiz, Antonio; Amanlou, Massoud; Noghabi, Kambiz Akbari

2012-02-01

An extensive investigation was conducted to isolate indigenous bacterial strains with outstanding performance for biosurfactant production from different types of spoiled fruits, food-related products and food processing industries. An isolate was selected from 800 by the highest biosurfactant yield in soybean oil medium and it was identified by 16S rRNA and the two most relevant hypervariable regions of this gene; V3 and V6 as Pseudomonas aeruginosa MA01. The isolate was able to produce 12 g/l of a glycolipid-type biosurfactant and generally less efficient to emulsify vegetable oils compared to hydrocarbons and could emulsify corn and coconut oils more than 50%. However, emulsification index (E(24)) of different hydrocarbons including hexane, toluene, xylene, brake oil, kerosene and hexadecane was between 55.8% and 100%. The surface tension of pure water decreased gradually with increasing biosurfactant concentration to 32.5 mNm(-1) with critical micelle concentration (CMC) value of 10.1mg/l. Among all carbon substrates examined, vegetable oils were the most effective on biosurfactant production. Two glycolipid fractions were purified from the biosurfactant crude extracts, and FTIR and ES-MS were used to determine the structure of these compounds. The analysis indicated the presence of three major monorhamnolipid species: R(1)C(10)C(10), R(1)C(10)C(12:1), and R(1)C(10)C(12); as well as another three major dirhamnolipid species: R(2)C(10)C(10), R(2)C(10)C(12:1), and R(2)C(10)C(12). The strain sweep experiment for measuring the linear viscoelastic of biosurfactant showed that typical behavior characteristics of a weak viscoelastic gel, with storage modulus greater than loss modulus at all frequencies examined, both showing some frequency dependence. Copyright © 2011 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Production of a rhamnolipid-type biosurfactant by Pseudomonas ...

African Journals Online (AJOL)

The work herewith investigated the effect of the culture medium composition on rhamnolipid production by Pseudomonas aeruginosa LBM10, previously isolated from an estuarine environment in Southern Brazil. Experimental design and surface response methodology were used in order to improve biosurfactant ...

Biosurfactants production from cheese whey

OpenAIRE

Rodrigues, L. R.; Teixeira, J. A.

2008-01-01

Biosurfactants are molecules that exhibit pronounced surface and emulsifying activities, produced by a variety of microorganisms. A host of interesting features of biosurfactants, such as higher biodegradability, lower toxicity, and effectiveness at extremes of temperature, pH and salinity; have led to a wide range of potential applications in the fields of oil recovery, environmental bioremediation, food processing and medicine. In spite of the immense potential of...

Production and characterization of biosurfactant from marine Streptomyces species B3.

Science.gov (United States)

Khopade, Abhijit; Ren, Biao; Liu, Xiang-Yang; Mahadik, Kakasaheb; Zhang, Lixin; Kokare, Chandrakant

2012-02-01

The present study demonstrates the production and properties of a biosurfactant isolated from marine Streptomyces species B3. The production of the biosurfactant was found to be higher in medium containing sucrose and lower in the medium containing glycerol. Yeast extract was the best nitrogen source for the production of the biosurfactant. The isolated biosurfactant reduced the surface tension of water to 29 mN/m. The purified biosurfactant was shown critical micelle concentrations of 110 mg/l. The emulsifying activity and stability of the biosurfactant was investigated at different salinities, pH, and temperature. The biosurfactant was effective at very low concentrations over a wide range of temperature, pH, and salt concentration. The purified biosurfactant was shown strong antimicrobial activity. The biosurfactant was produced from the marine Streptomyces sp. using non-hydrocarbon substrates such as sucrose that was readily available and not required extensive purification procedure. Streptomyces species B3 can be used for microbially enhanced oil recovery process. Copyright © 2011 Elsevier Inc. All rights reserved.

Enhancement of Bacillus subtilis Lipopeptide Biosurfactants Production through Optimization of Medium Composition and Adequate Control of Aeration.

Science.gov (United States)

Ghribi, Dhouha; Ellouze-Chaabouni, Semia

2011-01-01

Interest in biosurfactants has increased considerably in recent years, as they are potentially used in many commercial applications in petroleum, pharmaceuticals, biomedical, and food processing industries. Since improvement of their production was of great importance to reduce the final coast, cultural conditions were analyzed to optimize biosurfactants production from Bacillus subtilis SPB1 strain. A high yield of biosurfactants was obtained from a culture of B. subtilis using carbohydrate substrate as a carbon source; among carbohydrates, glucose enhanced the best surfactin production. The optimum glucose concentration was 40 g/L. Higher amount of biosurfactants was obtained using 5 g/L of urea as organic nitrogen source and applying C/N ratio of 7 with ammonium chloride as inorganic nitrogen source. The highest amount of biosurfactants was recorded with the addition of 2% kerosene. Moreover, it was shown, using an automated full-controlled 2.6 L fermenter, that aeration of the medium, which affected strongly the growth regulated biosurfactants synthesis by the producing cell. So that, low or high aerations lead to a decrease of biosurfactants synthesis yields. It was found that when using dissolved oxygen saturation of the medium at 30%, biosurfactants production reached 4.92 g/L.

Production and characterization of novel self-assembling biosurfactants from Aspergillus flavus.

Science.gov (United States)

Ishaq, U; Akram, M S; Iqbal, Z; Rafiq, M; Akrem, A; Nadeem, M; Shafi, F; Shafiq, Z; Mahmood, S; Baig, M A

2015-10-01

This work was conducted to produce, purify and characterize biosurfactants from Aspergillus flavus AF612 isolated from citrus fruit. Biosurfactant named 'Uzmaq' was isolated from A. flavus AF612. The chemical characterization of the biosurfactant was conducted. Biosurfactant Uzmaq produced by A. flavus, was composed of methoxy phenyl oxime glycosides. Two molecular forms of the biosurfactant, Uzmaq-A and Uzmaq-B were isolated. Biological properties (antifungal activity) were evaluated. The fractions of the biosurfactant were isolated and their surface properties were analysed. Uzmaq-A and Uzmaq-B had critical micelle concentration (CMC) around 170 and 80 mg l(-1) , and lowered surface tension of water up to 20 and 25 m Nm(-1) respectively. The biosurfactants were stable at pH 3-12 and temperature up to 80°C. Growth and biosurfactant production kinetics were also analysed. Novel biosurfactant Uzmaq was produced from A. flavus, which was composed of methoxy phenyl oxime glycosides. The surface activity of Uzmaq was better than the maximum values of synthetic chemical surfactants. The biosurfactant showed antifungal activity and self-assembling properties. Aspergillus flavus AF612 can be used for commercial production of Uzmaq that may be employed for controlled drug release applications and bioremediation. © 2015 The Society for Applied Microbiology.

Isolation of Biosurfactant Producing Bacteria from Oil Reservoirs

OpenAIRE

A Tabatabaee, M Mazaheri Assadi, AA Noohi,VA Sajadian

2005-01-01

Biosurfactants or surface-active compounds are produced by microoaganisms. These molecules reduce surface tension both aqueous solutions and hydrocarbon mixtures. In this study, isolation and identification of biosurfactant producing bacteria were assessed. The potential application of these bacteria in petroleum industry was investigated. Samples (crude oil) were collected from oil wells and 45 strains were isolated. To confirm the ability of isolates in biosurfactant production, haemolysis ...

Production and characterization of biosurfactant from Pseudomonas ...

African Journals Online (AJOL)

Further characterization of biosurfactant using Fourier transform infrared spectroscopy (FTIR) revealed it as a rhamnolipid. Keywords: Mangrove ecosystems, Pseudomonas aeruginosa, biosurfactant, critical micelle concentration (CMC), FT-IR fourier transform infrared spectroscopy (FTIR). African Journal of Biotechnology, ...

Emulsification of Hydrocarbons by Biosurfactant: Exclusive Use of Agrowaste

Directory of Open Access Journals (Sweden)

Olusola Solomon Amodu

2014-04-01

Full Text Available Novel biosurfactant-producing strains were isolated from hydrocarbon-contaminated environments that exclusively utilize agro-waste as their primary carbon source for the expression of biosurfactants. These were quantified using various standardized methods. Among the agro-waste screened, Beta vulgaris (Beetroot proved to be the most suitable substrate, for which the biosurfactants produced by three bacterial isolates–B. licheniformis STK01, B. subtilis STK02, and P. aeruginosa STK03–lowered the surface tension of the culture media to 30.0, 32.98, and 30.37 mN/m, respectively. The biosurfactants achieved considerable emulsification activity, particularly for heavy hydrocarbons, with the highest emulsification indices being 65.5% and 95% for anthracene and lubricant oil, respectively. The emulsion formed with lubricant oil was thermally stable even up to 50 °C for 21 days. The results showed the proficiency of the novel bacterial isolates used, as well as the suitability of solid agro-waste for biosurfactant production, thus suggesting that exclusive utilization of solid agro-waste is a promising option for use in biosurfactant production for environmental remediation. The outstanding emulsification activity and thermal stability demonstrated by the biosurfactants produced showed their potential applications in enhancing bioavailability and bioremediation of recalcitrant and hydrophobic environmental contaminants.

Effects of Fe nanoparticles on bacterial growth and biosurfactant production

Science.gov (United States)

Liu, Jia; Vipulanandan, Cumaraswamy; Cooper, Tim F.; Vipulanandan, Geethanjali

2013-01-01

Environmental conditions can have a major impact on bacterial growth and production of secondary products. In this study, the effect of different concentrations of Fe nanoparticles on the growth of Serratia sp. and on its production of a specific biosurfactant was investigated. The Fe nanoparticles were produced using the foam method, and the needle-shaped nanoparticles were about 30 nm in diameter. It was found that Fe nanoparticles can have either a positive or a negative impact on the bacterial growth and biosurfactant production, depending on their concentration. At 1 mg/L of Fe nanoparticle concentration the bacterial growth increased by 57 % and biosurfactant production increased by 63 %. When the Fe nanoparticle concentration was increased to 1 g/L, the bacterial growth decreased by 77 % and biosurfactant activity was undetectable. The biosurfactant itself was not directly affected by Fe nanoparticles over the range of concentrations studied, indicating that the observed changes in biosurfactant activity resulted indirectly from the effect of nanoparticles on the bacteria. These negative effects with nanoparticle exposures were temporary, demonstrated by the restoration of biosurfactant activity when the bacteria initially exposed to Fe nanoparticles were allowed to regrow in the absence of nanoparticles. Finally, the kinetics of bacterial growth and biosurfactant production were modeled. The model's predictions agreed with the experimental results.

Screening concepts for the isolation of biosurfactant producing microorganisms.

Science.gov (United States)

Walter, Vanessa; Syldatk, Christoph; Hausmann, Rudolf

2010-01-01

This chapter gives an overview of current methods for the isolation of biosurfactant producing microbes. The common screening methods for biosurfactants are presented. Sampling and isolation of bacteria are the basis for screening of biosurfactant producing microbes. Hydrocarbon-contaminated sites are the most promising for the isolation of biosurfactant producing microbes, but many strains have also been isolated from undisturbed sites. In subsequent steps the isolates have to be characterized in order to identify the strains which are interesting for a further investigation. Several techniques have been developed for identifying biosurfactant producing strains. Most of them are directly based on the surface or interfacial activity of the culture supernatant. Apart from that, some screening methods explore the hydrophobicity of the cell surface. This trait also gives an indication on biosurfactant production. In recent years automation and miniaturization have led to the development of high throughput methods for screening. High throughput screening (HTS) for analyzing large amounts of potential candidates or whole culture collections is reflected in the end. However, no new principals have been introduced by HTS methods.

Alternative methodology for isolation of biosurfactant-producing bacteria

OpenAIRE

Krepsky, N.; Da Silva, FS.; Fontana, LF.; Crapez, MAC.

2007-01-01

Wide biosurfactant application on biorremediation is limited by its high production cost. The search for cheaper biossurfactant production alternatives has guided our study. The use of selective media containing sucrose (10 g.L-1) and Arabian Light oil (2 g.L-1) as carbon sources showed to be effective to screen and maintain biosurfactant-producing consortia isolated from mangrove hydrocarbon-contaminated sediment. The biosurfactant production was assayed by kerosene, gasoline and Arabian Lig...

Interactions between biosurfactant-producing Pseudomonas and Phytophthora species

OpenAIRE

Tran, H.

2007-01-01

Fluorescent Pseudomonas bacteria produce a wide variety of antimicrobial metabolites, including soap-like compounds referred to as biosurfactants. The results of this thesis showed that biosurfactant-producing Pseudomonas bacteria are effective in controlling Phytophthora foot rot disease of black pepper in Vietnam and promote root and shoot development of the ‘King of Spices’. Biosurfactant-producing P. fluorescens strain SS101 was also effective in controlling tomato late blight caused by P...

Potential biosurfactant producing endophytic and epiphytic fungi ...

African Journals Online (AJOL)

Potential biosurfactant producing endophytic and epiphytic fungi, isolated from macrophytes in the Negro River in Manaus, Amazonas, Brazil. ... Solms and Cyperus ligularis L., macrophytes collected from oil-contaminated waters, were studied to assess their potential for producing biosurfactants; the most promising ones ...

Biosurfactant-enhanced bioremediation of polycyclic aromatic hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Cameotra, S.S.; Bollag, J.M. [Penn State University, University Park, PA (USA). Soil Biochemical Lab.

2003-07-01

Biosurfactants are surface-active compounds synthesized by it wide variety of micro-organisms. They are molecules that have both hydrophobic and hydrophilic domains and are capable of lowering the surface tension and the interfacial tension of the growth medium. Biosurfactants possess different chemical structures - lipopeptides, glycolipids, neutral lipids, and fatty acids. They are nontoxic biomolecules that are biodegradable. Biosurfactants also exhibit strong emulsification of hydrophobic compounds and form stable emulsions. Polycyclic aromatic hydrocarbons (PAHs) can be toxic, mutagenic, and carcinogenic compounds that pollute the environment. They are released to the environment its a result of spillage of oil and byproducts of coal treatment processes. The low water solubility of PAHs limits their availability to microorganisms, which is a potential problem for bioremediation of PAH-contaminated sites. Microbially produced surfactants enhance the bioavailability of these hydrophobic compounds for bioremediation. Therefore, biosurfactant-enhanced solubility of PAHs has potential applications in bioremediation.

First report of a lipopeptide biosurfactant from thermophilic bacterium Aneurinibacillus thermoaerophilus MK01 newly isolated from municipal landfill site.

Science.gov (United States)

Sharafi, Hakimeh; Abdoli, Mahya; Hajfarajollah, Hamidreza; Samie, Nima; Alidoust, Leila; Abbasi, Habib; Fooladi, Jamshid; Zahiri, Hossein Shahbani; Noghabi, Kambiz Akbari

2014-07-01

A biosurfactant-producing thermophile was isolated from the Kahrizak landfill of Tehran and identified as a bacterium belonging to the genus Aneurinibacillus. A thermostable lipopeptide-type biosurfactant was purified from the culture medium of this bacterium and showed stability in the temperature range of 20-90 °C and pH range of 5-10. The produced biosurfactant could reduce the surface tension of water from 72 to 43 mN/m with a CMC of 1.21 mg/mL. The strain growing at a temperature of 45 °C produces a substantial amount of 5 g/L of biosurfactant in the medium supplemented with sunflower oil as the sole carbon source. Response surface methodology was employed to optimize the biosurfactant production using sunflower oil, sodium nitrate, and yeast extract as variables. The optimization resulted in 6.75 g/L biosurfactant production, i.e., 35% improved as compared to the unoptimized condition. Thin-layer chromatography, FTIR spectroscopy, 1H-NMR spectroscopy, and biochemical composition analysis confirmed the lipopeptide structure of the biosurfactant.

Utilization of oleo-chemical industry by-products for biosurfactant production

Science.gov (United States)

2013-01-01

Biosurfactants are the surface active compounds produced by micro-organisms. The eco-friendly and biodegradable nature of biosurfactants makes their usage more advantageous over chemical surfactants. Biosurfactants encompass the properties of dropping surface tension, stabilizing emulsions, promoting foaming and are usually non- toxic and biodegradable. Biosurfactants offer advantages over their synthetic counterparts in many applications ranging from environmental, food, and biomedical, cosmetic and pharmaceutical industries. The important environmental applications of biosurfactants include bioremediation and dispersion of oil spills, enhanced oil recovery and transfer of crude oil. The emphasis of present review shall be with reference to the commercial production, current developments and future perspectives of a variety of approaches of biosurfactant production from the micro-organisms isolated from various oil- contaminated sites and from the by-products of oleo-chemical industry wastes/ by-products viz. used edible oil, industrial residues, acid oil, deodorizer distillate, soap-stock etc. PMID:24262384

Biosurfactants: promising bioactive molecules for oral-related health applications.

Science.gov (United States)

Elshikh, Mohamed; Marchant, Roger; Banat, Ibrahim M

2016-09-01

Biosurfactants are naturally produced molecules that demonstrate potentially useful properties such as the ability to reduce surface tensions between different phases. Besides having similar properties to their artificial chemical counterparts, they are regarded as environmental friendly, biodegradable and less toxic, which make them desirable candidates for downstream applications. The structure-activity-related properties of the biosurfactants which are directly correlated with potency of the biosurfactants as antimicrobial agents, the ability of the biosurfactants to alter surface energies and their ability to increase bioavailability are particularly what attract researchers to exploit their potential use in the oral-related health applications. Current research into biosurfactant indicates significant future potential for use in cosmetic and therapeutic oral hygiene product formulations and related medical device treatments. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Unexplored Brazilian oceanic island host high salt tolerant biosurfactant-producing bacterial strains.

Science.gov (United States)

da Silva, Fábio Sérgio Paulino; Pylro, Victor Satler; Fernandes, Pericles Leonardo; Barcelos, Gisele Souza; Kalks, Karlos Henrique Martins; Schaefer, Carlos Ernesto Gonçalves Reynaud; Tótola, Marcos Rogério

2015-05-01

We aimed to isolate biosurfactant-producing bacteria in high salt conditions from uncontaminated soils on the Brazilian oceanic island, Trindade. Blood agar medium was used for the isolation of presumptive biosurfactant-producing bacteria. Confirmation and measurements of biosurfactant production were made using an oil-spreading method. The isolates were identified by fatty acid profiles and partial 16S rRNA gene sequence analysis. A total of 14 isolates obtained from the 12 soil samples were found to produce biosurfactants. Among them, two isolates stood out as being able to produce biosurfactant that is increasingly active in solutions containing up to 175 g L(-1) NaCl. These high salt tolerant biosurfactant producers are affiliated to different species of the genus Bacillus. Soil organic matter showed positive correlation with the number of biosurfactant-producing bacteria isolated from our different sampling sites. The applied approach successfully recovered and identified biosurfactant-producing bacteria from non-contaminated soils. Due to the elevated salt tolerance, as well as their capacity to produce biosurfactants, these isolates are promising for environmental biotechnological applications, especially in the oil production chain.

Potential therapeutic applications of biosurfactants.

Science.gov (United States)

Gudiña, Eduardo J; Rangarajan, Vivek; Sen, Ramkrishna; Rodrigues, Lígia R

2013-12-01

Biosurfactants have recently emerged as promising molecules for their structural novelty, versatility, and diverse properties that are potentially useful for many therapeutic applications. Mainly due to their surface activity, these molecules interact with cell membranes of several organisms and/or with the surrounding environments, and thus can be viewed as potential cancer therapeutics or as constituents of drug delivery systems. Some types of microbial surfactants, such as lipopeptides and glycolipids, have been shown to selectively inhibit the proliferation of cancer cells and to disrupt cell membranes causing their lysis through apoptosis pathways. Moreover, biosurfactants as drug delivery vehicles offer commercially attractive and scientifically novel applications. This review covers the current state-of-the-art in biosurfactant research for therapeutic purposes, providing new directions towards the discovery and development of molecules with novel structures and diverse functions for advanced applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of Fe nanoparticles on bacterial growth and biosurfactant production

Energy Technology Data Exchange (ETDEWEB)

Liu Jia; Vipulanandan, Cumaraswamy, E-mail: cvipulanandan@uh.edu [University of Houston, Department of Civil and Environmental Engineering (United States); Cooper, Tim F. [University of Houston, Department of Biology and Biochemistry (United States); Vipulanandan, Geethanjali [University of Houston, Department of Biomedical Engineering (United States)

2013-01-15

Environmental conditions can have a major impact on bacterial growth and production of secondary products. In this study, the effect of different concentrations of Fe nanoparticles on the growth of Serratia sp. and on its production of a specific biosurfactant was investigated. The Fe nanoparticles were produced using the foam method, and the needle-shaped nanoparticles were about 30 nm in diameter. It was found that Fe nanoparticles can have either a positive or a negative impact on the bacterial growth and biosurfactant production, depending on their concentration. At 1 mg/L of Fe nanoparticle concentration the bacterial growth increased by 57 % and biosurfactant production increased by 63 %. When the Fe nanoparticle concentration was increased to 1 g/L, the bacterial growth decreased by 77 % and biosurfactant activity was undetectable. The biosurfactant itself was not directly affected by Fe nanoparticles over the range of concentrations studied, indicating that the observed changes in biosurfactant activity resulted indirectly from the effect of nanoparticles on the bacteria. These negative effects with nanoparticle exposures were temporary, demonstrated by the restoration of biosurfactant activity when the bacteria initially exposed to Fe nanoparticles were allowed to regrow in the absence of nanoparticles. Finally, the kinetics of bacterial growth and biosurfactant production were modeled. The model's predictions agreed with the experimental results.

Effects of Fe nanoparticles on bacterial growth and biosurfactant production

International Nuclear Information System (INIS)

Liu Jia; Vipulanandan, Cumaraswamy; Cooper, Tim F.; Vipulanandan, Geethanjali

2013-01-01

Environmental conditions can have a major impact on bacterial growth and production of secondary products. In this study, the effect of different concentrations of Fe nanoparticles on the growth of Serratia sp. and on its production of a specific biosurfactant was investigated. The Fe nanoparticles were produced using the foam method, and the needle-shaped nanoparticles were about 30 nm in diameter. It was found that Fe nanoparticles can have either a positive or a negative impact on the bacterial growth and biosurfactant production, depending on their concentration. At 1 mg/L of Fe nanoparticle concentration the bacterial growth increased by 57 % and biosurfactant production increased by 63 %. When the Fe nanoparticle concentration was increased to 1 g/L, the bacterial growth decreased by 77 % and biosurfactant activity was undetectable. The biosurfactant itself was not directly affected by Fe nanoparticles over the range of concentrations studied, indicating that the observed changes in biosurfactant activity resulted indirectly from the effect of nanoparticles on the bacteria. These negative effects with nanoparticle exposures were temporary, demonstrated by the restoration of biosurfactant activity when the bacteria initially exposed to Fe nanoparticles were allowed to regrow in the absence of nanoparticles. Finally, the kinetics of bacterial growth and biosurfactant production were modeled. The model’s predictions agreed with the experimental results.

Biosurfactants Produced by Marine Microorganisms with Therapeutic Applications.

Science.gov (United States)

Gudiña, Eduardo J; Teixeira, José A; Rodrigues, Lígia R

2016-02-18

Marine microorganisms possess unique metabolic and physiological features and are an important source of new biomolecules, such as biosurfactants. Some of these surface-active compounds synthesized by marine microorganisms exhibit antimicrobial, anti-adhesive and anti-biofilm activity against a broad spectrum of human pathogens (including multi-drug resistant pathogens), and could be used instead of existing drugs to treat infections caused by them. In other cases, these biosurfactants show anti-cancer activity, which could be envisaged as an alternative to conventional therapies. However, marine biosurfactants have not been widely explored, mainly due to the difficulties associated with the isolation and growth of their producing microorganisms. Culture-independent techniques (metagenomics) constitute a promising approach to study the genetic resources of otherwise inaccessible marine microorganisms without the requirement of culturing them, and can contribute to the discovery of novel biosurfactants with significant biological activities. This paper reviews the most relevant biosurfactants produced by marine microorganisms with potential therapeutic applications and discusses future perspectives and opportunities to discover novel molecules from marine environments.

Biosurfactants Produced by Marine Microorganisms with Therapeutic Applications

Directory of Open Access Journals (Sweden)

Eduardo J. Gudiña

2016-02-01

Full Text Available Marine microorganisms possess unique metabolic and physiological features and are an important source of new biomolecules, such as biosurfactants. Some of these surface-active compounds synthesized by marine microorganisms exhibit antimicrobial, anti-adhesive and anti-biofilm activity against a broad spectrum of human pathogens (including multi-drug resistant pathogens, and could be used instead of existing drugs to treat infections caused by them. In other cases, these biosurfactants show anti-cancer activity, which could be envisaged as an alternative to conventional therapies. However, marine biosurfactants have not been widely explored, mainly due to the difficulties associated with the isolation and growth of their producing microorganisms. Culture-independent techniques (metagenomics constitute a promising approach to study the genetic resources of otherwise inaccessible marine microorganisms without the requirement of culturing them, and can contribute to the discovery of novel biosurfactants with significant biological activities. This paper reviews the most relevant biosurfactants produced by marine microorganisms with potential therapeutic applications and discusses future perspectives and opportunities to discover novel molecules from marine environments.

Biosurfactants in plant-Pseudomonas interactions and their importance to biocontrol.

Science.gov (United States)

D'aes, Jolien; De Maeyer, Katrien; Pauwelyn, Ellen; Höfte, Monica

2010-06-01

Production of biosurfactants is a common feature in bacteria, and in particular in plant-associated species. These bacteria include many plant beneficial and plant pathogenic Pseudomonas spp., which produce primarily cyclic lipopeptide and rhamnolipid type biosurfactants. Pseudomonas-derived biosurfactants are involved in many important bacterial functions. By modifying surface properties, biosurfactants can influence common traits such as surface motility, biofilm formation and colonization. Biosurfactants can alter the bio-availability of exogenous compounds, such as nutrients, to promote their uptake, and of endogenous metabolites, including phenazine antibiotics, resulting in an enhanced biological activity. Antibiotic activity of biosurfactants towards microbes could play a role in intraspecific competition, self-defence and pathogenesis. In addition, bacterial surfactants can affect plants in different ways, either protecting them from disease, or acting as a toxin in a plant-pathogen interaction. Biosurfactants are involved in the biocontrol activity of an increasing number of Pseudomonas strains. Consequently, further insight into the roles and activities of surfactants produced by bacteria could provide means to optimize the use of biological control as an alternative crop protection strategy. © 2009 Society for Applied Microbiology and Blackwell Publishing Ltd.

Isolation and identification of biosurfactant-producing strains from the genus Pseudomonas aeruginosa and antibacterial effects of biosurfactant production in vitro

Directory of Open Access Journals (Sweden)

Salman Ahmady-Asbchin

2013-01-01

Full Text Available Introduction: Biosurfactants are amphiphilic biological compounds produced extracellularly or as part of the cell membranes by a variety of microorganisms. Because of their use in various industries, they are of a particular importance. The aim of this study was to identify a strain of bacteria of the genus Pseudomonas aeruginosa biosurfactant producers. Materials and methods: In this study, different samples of oil, water and soil contaminated with oil were prepared. Hemolytic activity, emulsification activity and measurement of surface tension were used and selected strains were identified by biochemical tests. The nature and effect of antibacterial biosurfactant was evaluated for strain selection.Results: In this study, eighty eight bacterial strains were isolated. Twenty four strains were isolated from the isolated strains with hemolytic activity. Among which, 14 strains have emulsification activity more than 70% and at last four strains reached surface tension to be less than 40 mN/m. Selected strain based on biochemical tests was recognized as a Pseudomonas aeruginosa. The nature of biosurfactant was determined by TLC, and proved to be of glycolipid kind. Therefore, the produced biosurfactant of the selected strain had antibacterial activity against six bacterial infectious. Sensitive bacteria to the effects of biosurfactant extract of Pseudomonas aeruginosa83, was Staphylococcus aureus and the most resistant bacteria to these extract, was the Proteus mirabilis. The results of MIC, MBC showed that MIC of the extract in concentration of 63 and 125 mg/ml on Escherichia coli, Staphylococcus epidermidis and Staphylococcus aureus respectively. Also, the MBC were extract in concentration of 63 and 125mg/ml on Staphylococcus epidermidis and Staphylococcus aureus respectively.Discussion and conclusion: Pseudomonas aeruginosa had high potential in reducing the surface tension and biosurfactant extracted had high antibacterial effects. Therefore, it

Current status in biotechnological production and applications of glycolipid biosurfactants.

Science.gov (United States)

Paulino, Bruno Nicolau; Pessôa, Marina Gabriel; Mano, Mario Cezar Rodrigues; Molina, Gustavo; Neri-Numa, Iramaia Angélica; Pastore, Glaucia Maria

2016-12-01

Biosurfactants are natural compounds with surface activity and emulsifying properties produced by several types of microorganisms and have been considered an interesting alternative to synthetic surfactants. Glycolipids are promising biosurfactants, due to low toxicity, biodegradability, and chemical stability in different conditions and also because they have many biological activities, allowing wide applications in different fields. In this review, we addressed general information about families of glycolipids, rhamnolipids, sophorolipids, mannosylerythritol lipids, and trehalose lipids, describing their chemical and surface characteristics, recent studies using alternative substrates, and new strategies to improve of production, beyond their specificities. We focus in providing recent developments and trends in biotechnological process and medical and industrial applications.

Application of biosurfactant in oil spill management

International Nuclear Information System (INIS)

Juwarkar, A.; Babu, P.S.; Mishra, K.; Deshpande, M.

1993-01-01

Surfactants are surface active agents which reduce surface tension and interfacial tension between two immiscible phases and help in emulsification. Toxicity, nonbiodegradability, and limited structural types of chemical surfactants have initiated the need for effective substitutes. Biosurfactants, which are synthesized by specific microbial cultures, have surface active properties comparable to chemical surfactants. They are compounds that can help in oil spill cleanup operations without presenting the problem posed by chemical surfactants. Two bacterial cultures were isolated from oil-contaminated soil and were used for biosurfactant production. The biosurfactants produced by Bacillus licheniformis, BS1, and Pseudomonas aeruginosa, BS2, in mineral media containing glucose as the carbon source belong to the class of lipoprotein and glycolipid, respectively. They were found to reduce the surface and interfacial tension of water and water-hexadecane system from 72 dynes/cm and 40 dynes/cm to 28 to 30 dynes/cm and 1 to 3 dynes/cm, respectively. These results were comparable with chemical surfactants with respect to surface tension reduction (Slic Gone 34 dynes/ cm and Castrol 30 dynes/cm). The low interfacial tension allows the formation of stable emulsion. The two cultures were grown on different substrates, namely, glucose, mannitol, glycerol, hexadecane, oily sludge, and crude oil. Emulsion formation of hexadecane in water was tested with the cell-free broth containing biosurfactant from the respective substrate broths. Emulsions of 56% stability to 100% stability were obtained from these biosurfactant-containing broths. Both biosurfactants were able to emulsify crude oil. A surfactant's ability to form a stable emulsion is the first step in oil spill cleanup. The emulsified oil can then be acted upon very easily by the microorganism under study

Biosurfactants: Multifunctional Biomolecules of the 21st Century.

Science.gov (United States)

Santos, Danyelle Khadydja F; Rufino, Raquel D; Luna, Juliana M; Santos, Valdemir A; Sarubbo, Leonie A

2016-03-18

In the era of global industrialisation, the exploration of natural resources has served as a source of experimentation for science and advanced technologies, giving rise to the manufacturing of products with high aggregate value in the world market, such as biosurfactants. Biosurfactants are amphiphilic microbial molecules with hydrophilic and hydrophobic moieties that partition at liquid/liquid, liquid/gas or liquid/solid interfaces. Such characteristics allow these biomolecules to play a key role in emulsification, foam formation, detergency and dispersal, which are desirable qualities in different industries. Biosurfactant production is considered one of the key technologies for development in the 21st century. Besides exerting a strong positive impact on the main global problems, biosurfactant production has considerable importance to the implantation of sustainable industrial processes, such as the use of renewable resources and "green" products. Biodegradability and low toxicity have led to the intensification of scientific studies on a wide range of industrial applications for biosurfactants in the field of bioremediation as well as the petroleum, food processing, health, chemical, agricultural and cosmetic industries. In this paper, we offer an extensive review regarding knowledge accumulated over the years and advances achieved in the incorporation of biomolecules in different industries.

Screening of potential biosurfactant-producing bacteria isolated from ...

African Journals Online (AJOL)

Seawater represents a specific environment harboring complex bacterial community which is adapted to harsh conditions. Hence, biosurfactant produced by these bacteria under these conditions have interesting proprieties. The screening of biosurfactant producing strains isolated from seawater biofilm was investigated.

Biomedical and therapeutic applications of biosurfactants

OpenAIRE

Rodrigues, L. R.; Teixeira, J. A.

2010-01-01

During the last years, several applications of biosurfactants with medical purposes have been reported. Biosurfactants are considered relevant molecules for applications in combating many diseases and as therapeutic agents due to their antibacterial, antifungal and antiviral activities. Furthermore, their role as anti-adhesive agents against several pathogens illustrate their utility as suitable anti-adhesive coating agents for medical insertional materials leading to a reduction of a large n...

Interactions between biosurfactant-producing Pseudomonas and Phytophthora species

NARCIS (Netherlands)

Tran, H.

2007-01-01

Fluorescent Pseudomonas bacteria produce a wide variety of antimicrobial metabolites, including soap-like compounds referred to as biosurfactants. The results of this thesis showed that biosurfactant-producing Pseudomonas bacteria are effective in controlling Phytophthora foot rot

Solubilization of Polycyclic Aromatic Hydrocarbons by Single and Binary Mixed Rhamnolipid-Sophorolipid Biosurfactants.

Science.gov (United States)

Song, Dandan; Liang, Shengkang; Yan, Lele; Shang, Yujun; Wang, Xiuli

2016-07-01

Biosurfactants are promising additives for surfactant enhanced remediation (SER) technologies due to their low toxicity and high biodegradability. To develop green and efficient additives for SER, the aqueous solubility enhancements of polycyclic aromatic hydrocarbons (PAHs; naphthalene, phenanthrene, and pyrene) by rhamnolipid (RL) and sophorolipid (SL) biosurfactants were investigated in single and binary mixed systems. The solubilization capacities were quantified in terms of the solubility enhancement factor, molar solubilization ratio (MSR), and micelle-water partition coefficient (). Rughbin's model was applied to evaluate the interaction parameters (β) in the mixed RL-SL micelles. The solubility of the PAHs increased linearly with the glycolipid concentration above the critical micelle concentration (CMC) in both single and mixed systems. Binary RL-SL mixtures exhibited greater solubilization than individual glycolipids. At a SL molar fraction of 0.7 to 0.8, the solubilization capacity was the greatest, and the MSR and reached their maximum values, and β values became positive. These results suggest that the two biosurfactants act synergistically to increase the solubility of the PAHs. The solubilization capacity of the RL-SL mixtures increased with increasing temperature and decreased with increasing salinity. The aqueous solubility of phenanthrene reached a maximum value at pH of 5.5. Moreover, the mixed RL-SL systems exhibited a strong ability to solubilize PAHs, even in the presence of heavy metal ions. These mixed biosurfactant systems have the potential to improve the performance of SER technologies using biosurfactants to solubilize hydrophobic organic contaminants by decreasing the applied biosurfactant concentration, which reduces the costs of remediation. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Utilization of sludge palm oil as a novel substrate for biosurfactant production.

Science.gov (United States)

Wan Nawawi, Wan Mohd Fazli; Jamal, Parveen; Alam, Md Zahangir

2010-12-01

This paper introduces sludge palm oil (SPO) as a novel substrate for biosurfactant production by liquid state fermentation. Potential strains of microorganism were isolated from various hydrocarbon-based sources at palm oil mill and screened for biosurfactant production with the help of drop collapse method and surface tension activity. Out of 22 isolates of microorganism, the strain S02 showed the highest bacterial growth with a surface tension of 36.2 mN/m and was therefore, selected as a potential biosurfactant producing microorganism. Plackett-Burman experimental design was employed to determine the important nutritional requirement for biosurfactant production by the selected strain under controlled conditions. Six out of 11 factors of the production medium were found to significantly affect the biosurfactant production. K(2)HPO(4) had a direct proportional correlation with the biosurfactant production while sucrose, glucose, FeSO(4), MgSO(4), and NaNO(3) showed inversely proportional relationship with biosurfactant production in the selected experimental range. 2010 Elsevier Ltd. All rights reserved.

Biosurfactants: Multifunctional Biomolecules of the 21st Century

Directory of Open Access Journals (Sweden)

Danyelle Khadydja F. Santos

2016-03-01

Full Text Available In the era of global industrialisation, the exploration of natural resources has served as a source of experimentation for science and advanced technologies, giving rise to the manufacturing of products with high aggregate value in the world market, such as biosurfactants. Biosurfactants are amphiphilic microbial molecules with hydrophilic and hydrophobic moieties that partition at liquid/liquid, liquid/gas or liquid/solid interfaces. Such characteristics allow these biomolecules to play a key role in emulsification, foam formation, detergency and dispersal, which are desirable qualities in different industries. Biosurfactant production is considered one of the key technologies for development in the 21st century. Besides exerting a strong positive impact on the main global problems, biosurfactant production has considerable importance to the implantation of sustainable industrial processes, such as the use of renewable resources and “green” products. Biodegradability and low toxicity have led to the intensification of scientific studies on a wide range of industrial applications for biosurfactants in the field of bioremediation as well as the petroleum, food processing, health, chemical, agricultural and cosmetic industries. In this paper, we offer an extensive review regarding knowledge accumulated over the years and advances achieved in the incorporation of biomolecules in different industries.

Antimicrobial potential of a lipopeptide biosurfactant derived from a marine Bacillus circulans.

Science.gov (United States)

Das, P; Mukherjee, S; Sen, R

2008-06-01

To isolate the biologically active fraction of the lipopeptide biosurfactant produced by a marine Bacillus circulans and study its antimicrobial potentials. The marine isolate B. circulans was cultivated in glucose mineral salts medium and the crude biosurfactant was isolated by chemical isolation method. The crude biosurfactants were solvent extracted with methanol and the methanol extract was subjected to reverse phase high-performance liquid chromatography (HPLC). The crude biosurfactants resolved into six major fractions in HPLC. The sixth HPLC fraction eluting at a retention time of 27.3 min showed the maximum surface tension-reducing property and reduced the surface tension of water from 72 mNm(-1) to 28 mNm(-1). Only this fraction was found to posses bioactivity and showed a pronounced antimicrobial action against a panel of Gram-positive and Gram-negative pathogenic and semi-pathogenic micro-organisms including a few multidrug-resistant (MDR) pathogenic clinical isolates. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of this antimicrobial fraction of the biosurfactant were determined for these test organisms. The biosurfactant was found to be active against Gram-negative bacteria such as Proteus vulgaris and Alcaligens faecalis at a concentration as low as 10 microg ml(-1). The biosurfactant was also active against methicillin-resistant Staphylococcus aureus (MRSA) and other MDR pathogenic strains. The chemical identity of this bioactive biosurfactant fraction was determined by post chromatographic detection using thin layer chromatography (TLC) and also by Fourier transform infrared (FTIR) spectroscopy. The antimicrobial HPLC fraction resolved as a single spot on TLC and showed positive reaction with ninhydrin, iodine and rhodamine-B reagents, indicating its lipopeptide nature. IR absorption by this fraction also showed similar and overlapping patterns with that of other lipopeptide biosurfactants such as surfactin

BIOSURFACTANTS PRODUCTION BY Pseudomonas aeruginosa USING SOYBEAN OIL AS SUBSTRATE

Directory of Open Access Journals (Sweden)

Venty Suryanti

2010-06-01

Full Text Available Optimization condition of the biosurfactants production by P. aeruginosa using soybean oil as substrate has been examined. The media containing 10% v/v of the soybean oil and 6 days of the fermentation time was the optimum condition for the biosurfactants production. The extraction technique using different solvent polarity (n-hexane, chloroform, ethyl acetate and buthanol, respectively was applied for the isolation of the biosurfactants. The biosurfactant was found in the extract chloroform of the crude biospasoy (biosurfactants obtained from soybean oil as substrate which then is called chlo-biospasoy. The chlo-biospasoy was identified as rhamnolipids which had oil in water (o/w emulsion type, had the CMC of 860 mg/L and could reduced the surface tension of the water from 72 mN/m to 52 mN/m. The chlo-biospasoy could be used as an emulsifier to form emulsion between water and hydrocarbon such as palm oil, benzene, premium or toluene with various stability. The results indicated that chlo-biospasoy could be used as an emulsifying and emulsion-stabilizing agent.     Keywords: Biosurfactants, P. aeruginosa, Soybean Oil, Emulsifier

Effect of rhamnolipid biosurfactant on solubilization of polycyclic aromatic hydrocarbons.

Science.gov (United States)

Li, Shudong; Pi, Yongrui; Bao, Mutai; Zhang, Cong; Zhao, Dongwei; Li, Yiming; Sun, Peiyan; Lu, Jinren

2015-12-15

Rhamnolipid biosurfactant-producing bacteria, Bacillus Lz-2, was isolated from oil polluted water collected from Dongying Shengli oilfield, China. The factors that influence PAH solubilization such as biosurfactant concentration, pH, ionic strength and temperature were discussed. The results showed that the solubilities of naphthalene, phenanthrene and pyrene increased linearly with the rise of rhamnolipid biosurfactant dose above the biosurfactant critical micelle concentration (CMC). Furthermore, the molar solubilization ratio (MSR) values decreased in the following order: naphthalene>phenanthrene>pyrene. However, the solubility percentage increased and followed the opposite order: pyrene>phenanthrene>naphthalene. The solubilities of PAHs in rhamnolipid biosurfactant solution increased with the rise of pH and ionic strength, and reached the maximum values under the conditions of pH11 and NaCl concentration 8 g · L(-1). The solubility of phenanthrene and pyrene increased with the rise of temperature. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biofilm disruption potential of a glycolipid biosurfactant from marine Brevibacterium casei.

Science.gov (United States)

Kiran, George Seghal; Sabarathnam, Balu; Selvin, Joseph

2010-08-01

The antibiofilm activity of a glycolipid biosurfactant isolated from the marine actinobacterium Brevibacterium casei MSA19 was evaluated against pathogenic biofilms in vitro. The isolate B. casei MSA19 was a potential biosurfactant producer among the 57 stable strains isolated from the marine sponge Dendrilla nigra. The biosurfactant production was optimized under submerged fermentation. The purified glycolipid showed a broad spectrum of antimicrobial activity. Based on the minimum inhibitory concentration/minimum bactericidal concentration ratio, the glycolipid was determined as bacteriostatic. The glycolipid biosurfactant disrupted the biofilm formation under dynamic conditions. The disruption of the biofilm by the MSA19 glycolipid was consistent against mixed pathogenic biofilm bacteria. Therefore, the glycolipid biosurfactant can be used as a lead compound for the development of novel antibiofilm agents.

Partial Characterization of Biosurfactant from Lactobacillus pentosus and Comparison with Sodium Dodecyl Sulphate for the Bioremediation of Hydrocarbon Contaminated Soil

Directory of Open Access Journals (Sweden)

A. B. Moldes

2013-01-01

Full Text Available The capability of a cell bound biosurfactant produced by Lactobacillus pentosus, to accelerate the bioremediation of a hydrocarbon-contaminated soil, was compared with a synthetic anionic surfactant (sodium dodecyl sulphate SDS-. The biosurfactant produced by the bacteria was analyzed by Fourier transform infrared spectroscopy (FTIR that clearly indicates the presence of OH and NH groups, C=O stretching of carbonyl groups and NH nebding (peptide linkage, as well as CH2–CH3 and C–O stretching, with similar FTIR spectra than other biosurfactants obtained from lactic acid bacteria. After the characterization of biosurfactant by FTIR, soil contaminated with 7,000 mg Kg−1 of octane was treated with biosurfactant from L. pentosus or SDS. Treatment of soil for 15 days with the biosurfactant produced by L. pentosus led to a 65.1% reduction in the hydrocarbon concentration, whereas SDS reduced the octane concentration to 37.2% compared with a 2.2% reduction in the soil contaminated with octane in absence of biosurfactant used as control. Besides, after 30 days of incubation soil with SDS or biosurfactant gave percentages of bioremediation around 90% in both cases. Thus, it can be concluded that biosurfactant produced by L. pentosus accelerates the bioremediation of octane-contaminated soil by improving the solubilisation of octane in the water phase of soil, achieving even better results than those reached with SDS after 15-day treatment.

Partial Characterization of Biosurfactant from Lactobacillus pentosus and Comparison with Sodium Dodecyl Sulphate for the Bioremediation of Hydrocarbon Contaminated Soil

Science.gov (United States)

Moldes, A. B.; Paradelo, R.; Vecino, X.; Cruz, J. M.; Gudiña, E.; Rodrigues, L.; Teixeira, J. A.; Domínguez, J. M.; Barral, M. T.

2013-01-01

The capability of a cell bound biosurfactant produced by Lactobacillus pentosus, to accelerate the bioremediation of a hydrocarbon-contaminated soil, was compared with a synthetic anionic surfactant (sodium dodecyl sulphate SDS-). The biosurfactant produced by the bacteria was analyzed by Fourier transform infrared spectroscopy (FTIR) that clearly indicates the presence of OH and NH groups, C=O stretching of carbonyl groups and NH nebding (peptide linkage), as well as CH2–CH3 and C–O stretching, with similar FTIR spectra than other biosurfactants obtained from lactic acid bacteria. After the characterization of biosurfactant by FTIR, soil contaminated with 7,000 mg Kg−1 of octane was treated with biosurfactant from L. pentosus or SDS. Treatment of soil for 15 days with the biosurfactant produced by L. pentosus led to a 65.1% reduction in the hydrocarbon concentration, whereas SDS reduced the octane concentration to 37.2% compared with a 2.2% reduction in the soil contaminated with octane in absence of biosurfactant used as control. Besides, after 30 days of incubation soil with SDS or biosurfactant gave percentages of bioremediation around 90% in both cases. Thus, it can be concluded that biosurfactant produced by L. pentosus accelerates the bioremediation of octane-contaminated soil by improving the solubilisation of octane in the water phase of soil, achieving even better results than those reached with SDS after 15-day treatment. PMID:23691515

Identification of potential local isolated for biosurfactant production

Science.gov (United States)

Shafiei, Zahra; Yusoff, Wan Mohtar Wan; Hamid, Aidil Abdul; Moazami, Nasrin; Hamzah, Ainon; Fooladi, Taybeh

2013-11-01

Biosurfactant are amphiphilic molecule that have received increasing attention in recent years because of their role in the growth of microorganisms on water-insoluble hydrophobic materials such as hydrocarbons as well as their commercial potential in the cosmetics, food, oil recovery and agricultural industries. In this study a potential biosurfactant producing strain was isolated from several soil samples of Terengganu oil refinery, Malaysia and selected during preliminary screening using hemolytic activity, oil spreading and drop collapsed technique. Isolates with at least more than one positive response to these three methods were subjected to complementary screening by measuring surface tension reduction as well as emulsification capacity. The biosurfactant produced by isolated 5M was able to reduced surface tension of culture medium from 60 mN/m to30mN/m. The biochemical and morphological characterization, 16SrRNA gene sequencing showed that the isolated 5M belongs to bacillus groups. The maximum production of biosurfactant by Bacillus 5M was observed after 48 h of incubation.

Microbial biofilms: biosurfactants as antibiofilm agents.

Science.gov (United States)

Banat, Ibrahim M; De Rienzo, Mayri A Díaz; Quinn, Gerry A

2014-12-01

Current microbial inhibition strategies based on planktonic bacterial physiology have been known to have limited efficacy on the growth of biofilm communities. This problem can be exacerbated by the emergence of increasingly resistant clinical strains. All aspects of biofilm measurement, monitoring, dispersal, control, and inhibition are becoming issues of increasing importance. Biosurfactants have merited renewed interest in both clinical and hygienic sectors due to their potential to disperse microbial biofilms in addition to many other advantages. The dispersal properties of biosurfactants have been shown to rival those of conventional inhibitory agents against bacterial and yeast biofilms. This makes them suitable candidates for use in new generations of microbial dispersal agents and for use as adjuvants for existing microbial suppression or eradication strategies. In this review, we explore aspects of biofilm characteristics and examine the contribution of biologically derived surface-active agents (biosurfactants) to the disruption or inhibition of microbial biofilms.

Optimization of liquid-liquid extraction of biosurfactants from corn steep liquor.

Science.gov (United States)

Vecino, X; Barbosa-Pereira, L; Devesa-Rey, R; Cruz, J M; Moldes, A B

2015-09-01

In this work, the optimization of the operational conditions for the chloroform-based extraction of surface-active compounds from corn steep liquor (CSL) was carried out and the nutritional properties of the remnant aqueous phase (CSL-less biosurfactant) was evaluated as microbial fermentation medium. The optimal conditions to obtain biosurfactants from CSL were as follows: chloroform/CSL ratio 2 (v/v), 56 °C at extraction times >30 min. At the optima conditions, 100 % of biosurfactant extract can be obtained from CSL, obtaining 12.0 ± 0.5 g of biosurfactant extract/Kg of CSL. The critical micelle concentration (CMC) of the biosurfactant extract was 399.4 mg L(-1). This value is similar to the CMC of cetrimonium bromide (CTAB), a cationic surfactant used in the formulation of nanoparticles. The extraction of biosurfactant can be also carried out at room temperature although in this case, the extraction yield decreased about 15 %. The extraction of surface-active compounds from agroindustrial streams can suppose important advances for the bio-based surfactants industry. Biosurfactants obtained in this work are not only more eco-friendly than chemical detergents but also can be cost competitive with its chemical counterparts. Furthermore, after the extraction of surface-active compounds, CSL-less biosurfactant was found to be suitable as nutritional supplement for lactic acid bacteria, maintaining its nutritional properties in comparison with regular CSL.

Assessment of four different methods for selecting biosurfactant ...

African Journals Online (AJOL)

... and ease of use to screen biosurfactant producing six extremely halophilic bacteria isolated from saline soil of Chott El Hodna-M'sila (Algeria), which is considered as a thalassohaline environment. Results from screening methods revealed that, CH2 and CH5 strains are potential candidates for biosurfactant production.

Isolation and functional characterization of a biosurfactant produced by Lactobacillus paracasei.

Science.gov (United States)

Gudiña, Eduardo J; Teixeira, José A; Rodrigues, Lígia R

2010-03-01

In this study, the crude biosurfactant produced by a Lactobacillus paracasei strain isolated in a Portuguese dairy industry was characterized. The minimum surface tension (41.8mN/m) and the critical micelle concentration (2.5mg/ml) obtained were found to be similar to the values previously reported for biosurfactants isolated from other lactobacilli. The biosurfactant was found to be stable to pH changes over a range from 6 to 10, being more effective at pH 7, and showed no loss of surface activity after incubation at 60 degrees C for 120h. Although the biosurfactant chemical composition has not been determined yet, a fraction was isolated through acidic precipitation, which exhibited higher surface activity as compared with the crude biosurfactant. Furthermore, this isolated biosurfactant showed antimicrobial and anti-adhesive activities against several pathogenic microorganisms. In addition, L. paracasei exhibited a strong autoaggregating phenotype, which was maintained after washing and resuspending the cells in PBS, meaning that this attribute must be related to cell surface components and not to excreted factors. The autoaggregation ability exhibited by this strain, together with the antimicrobial and anti-adhesive properties observed for this biosurfactant opens the possibility for its use as an effective probiotic strain.

Synthesis of biosurfactants and their advantages to microorganisms and mankind.

Science.gov (United States)

Cameotra, Swaranjit Singh; Makkar, Randhir S; Kaur, Jasminder; Mehta, S K

2010-01-01

Biosurfactants are surface-active compounds synthesized by a wide variety of microorganisms. They are molecules that have both hydrophobic and hydrophilic domains and are capable of lowering the surface tension and the interfacial tension of the growth medium. Biosurfactants possess different chemical structures--lipopeptides, glycolipids, neutral lipids and fatty acids. They are nontoxic biomolecules that are biodegradable. Biosurfactants also exhibit strong emulsification of hydrophobic compounds and form stable emulsions. The low water solubility of these hydrophobic compounds limits their availability to microorganisms, which is a potential problem for bioremediation of contaminated sites. Microbially produced surfactants enhance the bioavailability of these hydrophobic compounds for bioremediation. Therefore, biosurfactant-enhanced solubility of pollutants has potential applications in bioremediation. Not only are the biosurfactants useful in a variety of industrial processes, they are also of vital importance to the microbes in adhesion, emulsification, bioavailability, desorption and defense strategy. These interesting facts are discussed in this chapter.

Evaluation and functional characterization of a biosurfactant produced by Lactobacillus plantarum CFR 2194.

Science.gov (United States)

Madhu, Arenahalli Ningegowda; Prapulla, Siddalingaiya Gurudutt

2014-02-01

The study details the investigations on the ability of Lactobacillus plantarum CFR 2194, an isolate from kanjika, a rice-based ayurvedic fermented product, to produce biosurfactant. Surfactant production, as a function of fermentation time, indicates that the maximum production occurred at 72 h under stationary conditions. Isolation, partial purification, and characterization of the biosurfactant produced have been carried out, and Fourier transform infrared spectroscopy (FTIR) spectra demonstrated that biosurfactants were constituted by protein and polysaccharide fractions, i.e., possessed the structure typical of glycoprotein, which is affected by the medium composition and the phase of growth of the biosurfactant-synthesizing strain. Critical micelle concentration (cmc) of the biosurfactant was found to be 6 g l(-1). The emulsification index (EI), emulsification activity (EA), and emulsion stability (ES) values of the biosurfactant have confirmed its emulsification property. Aqueous fractions of the produced biosurfactant exhibited a significant antimicrobial activity against the food-borne pathogenic species: Escherichia coli ATCC 31705, E. coli MTCC 108, Salmonella typhi, Yersinia enterocolitica MTCC 859, and Staphylococcus aureus F 722. More importantly, the biosurfactant from L. plantarum showed antiadhesive property against above food-borne pathogens. The results thus indicate the potential for developing strategies to prevent microbial colonization of food contact surfaces and health-care prosthesis using these biosurfactants.

Production of biosurfactant by indigenous isolated bacteria in fermentation system

Science.gov (United States)

Fooladi, Tayebeh; Hamid, Aidil Bin Abd; Yusoff, Wan Mohtar Wan; Moazami, Nasrin; Shafiee, Zahra

2013-11-01

Bacillus pumilus 2IR is a soil isolate bacterium from an Iranian oil field that produces promising yield of biosurfactant in medium E. The production of biosurfactant by strain 2IR has been investigated using different carbon and nitrogen sources. The strain was able to grow and to produce surfactant, reducing the surface tension of the medium from 60mN/m to 31mN/m on glucose after 72 h of cultivation. The strain was able to produce the maximum amount of biosurfactant (0.72 g/l) when potassium nitrate and glucose used as a nitrogen and carbon sources respectively. Production of biosurfactant reaches to highest amount at a C/N ratio of 12.

Investigation of biosurfactant production by Bacillus pumilus 1529 and Bacillus subtilis WPI

Directory of Open Access Journals (Sweden)

shila khajavi shojaei

2016-06-01

Full Text Available Introduction: Biosurfactants are unique amphipathic molecules with extensive application in removing organic and metal contaminants. The purpose of this study was to investigate production of biosurfactant and determine optimal conditions to produce biosurfactant by Bacillus pumilus 1529 and Bacillus subtilis WPI. Materials and methods: In this study, effect of carbon source, temperature and incubation time on biosurfactant production was evaluated. Hemolytic activity, emulsification activity, oil spreading, drop collapse, cell hydrophobicity and measurement of surface tension were used to detect biosurfactant production. Then, according to the results, the optimal conditions for biosurfactant production by and Bacillus subtilis WPI was determined. Results: In this study, both bacteria were able to produce biosurfactant at an acceptable level. Glucose, kerosene, sugarcane molasses and phenanthrene used as a sole carbon source and energy for the mentioned bacteria. Bacillus subtilis WPI produced maximum biosurfactant in the medium containing kerosene and reduced surface tension of the medium to 33.1 mN/m after 156 hours of the cultivation at 37°C. Also, the highest surface tension reduction by Bacillus pumilus 1529 occurred in the medium containing sugarcane molasses and reduce the surface tension of culture medium after 156 hours at 37°C from 50.4 to 28.83 mN/m. Discussion and conclusion: Bacillus pumilus 1529 and Bacillus subtilis WPI had high potential in production of biosurfactant and degradation of petroleum hydrocarbons and Phenanthrene. Therefore, it could be said that these bacteria had a great potential for applications in bioremediation and other environmental process.

Ex situ treatment of hydrocarbon-contaminated soil using biosurfactants from Lactobacillus pentosus.

Science.gov (United States)

Moldes, Ana Belén; Paradelo, Remigio; Rubinos, David; Devesa-Rey, Rosa; Cruz, José Manuel; Barral, María Teresa

2011-09-14

The utilization of biosurfactants for the bioremediation of contaminated soil is not yet well established, because of the high production cost of biosurfactants. Consequently, it is interesting to look for new biosurfactants that can be produced at a large scale, and it can be employed for the bioremediation of contaminated sites. In this work, biosurfactants from Lactobacillus pentosus growing in hemicellulosic sugars solutions, with a similar composition of sugars found in trimming vine shoot hydrolysates, were employed in the bioremediation of soil contaminated with octane. It was observed that the presence of biosurfactant from L. pentosus accelerated the biodegradation of octane in soil. After 15 days of treatment, biosurfactants from L. pentosus reduced the concentration of octane in the soil to 58.6 and 62.8%, for soil charged with 700 and 70,000 mg/kg of hydrocarbon, respectively, whereas after 30 days of treatment, 76% of octane in soil was biodegraded in both cases. In the absence of biosurfactant and after 15 days of incubation, only 1.2 and 24% of octane was biodegraded in soil charged with 700 and 70,000 mg/kg of octane, respectively. Thus, the use of biosurfactants from L. pentosus, as part of a well-designed bioremediation process, can provide mechanisms to mobilize the target contaminants from the soil surface to make them more available to the microbial population.

Optimization and characterization of biosurfactant from Streptomyces griseoplanus NRRL-ISP5009 (MS1).

Science.gov (United States)

Elkhawaga, M A

2018-03-01

This work aimed to study, isolate, characterize and stabilize the biosurfactant isolated from actinomycetes found in petroleum contaminated soil. Optimized production of the biosurfactant from Streptomyces griseoplanus NRRL-ISP5009, SM1 was obtained on day 6 at 30°C, pH 7, 150 rev min -1 , in glycerol yeast extract broth medium supplemented with cellulose, yeast extract and 1% NaCl. The stability of the biosurfactant produced was studied at different temperatures, pH and different concentrations of NaCl. The produced biosurfactant was extracted and purified. Streptomyces griseoplanus NRRL-ISP5009, SM1 isolated from oil contaminated soil produced a biosurfactant exhibiting emulsification activity. The produced biosurfactant is a mixture of carbohydrate, lipid and protein. It has promising characteristics, including a higher stability at alkaline pH than at acidic pH, a salinity of 1-3% and stable in the temperature range from 0 and 100°C. Also, the potential antimicrobial activity of the purified biosurfactant was recorded. The research was focused on the isolation of a novel source of biosurfactants that have great importance in the manufacture of food, detergent, pharmaceutical and cosmetics. © 2017 The Society for Applied Microbiology.

Effect of biosurfactants on the aqueous solubility of PCE and TCE.

Science.gov (United States)

Albino, John D; Nambi, Indumathi M

2009-12-01

The effect of biosurfactants on the solubility of tetrachloroethylene (PCE) and trichloroethylene (TCE) was studied in batch experiments pertaining to their use for solubilization and mobilization of such contaminants in surfactant enhanced aquifer remediation. Biosurfactants, rhamnolipid and surfactin used in solubility studies were synthesized in our laboratory by Pseudomonas aeruginosa (MTCC 2297) and Bacillus subtilis (MTCC 2423), respectively. The efficiency of the biosurfactants in solubilizing the chlorinated solvents was compared to that of synthetic surfactants. The Weight Solubilization Ratio (WSR) values for solubilization of PCE and TCE by biosurfactants were very high compared to the values obtained for synthetic surfactants. Surfactin proved to be a better surfactant over rhamnolipid. The WSR of surfactin on solubilization of PCE and TCE were 3.83 and 12.5, respectively, whereas the values obtained for rhamnolipid were 2.06 and 8.36. The solubility of the chlorinated solvents by biosurfactants was considerably affected by the changes in pH. The aqueous solubility of PCE and TCE increased tremendously with decrease in pH. The solubility of biosurfactants was observed to decrease with the pH, favoring partitioning of surfactants into the chlorinated solvents in significant amounts at lower pH. The excessive accumulation of biosurfactants at the interface facilitated interfacial tension reductions resulting in higher solubility of the chlorinated solvents at pH less than 7.

Carbohydrate-based renewable biosurfactants: Rhamnolipids, sophorolipids, and novel liamocins

Science.gov (United States)

High-yield, glycolipid-based biosurfactants are of increasing interest for use in environmentally benign cleaning or emulsifying agents. We have developed a MALDI-TOF/MS screen for the rapid analysis of several types of biosurfactants, including various acylated rhamnolipids in Pseudomonas extracts...

Isolation and characterization of biosurfactant producing bacteria from Persian Gulf (Bushehr provenance)

International Nuclear Information System (INIS)

Hassanshahian, Mehdi

2014-01-01

Highlights: • Biosurfactant producing bacteria were isolated from Persian Gulf. • There is high diversity of biosurfactant producing bacteria in the Persian Gulf. • These bacteria are very useful for management of oil pollution in the sea. - Abstract: Biosurfactants are surface active materials that are produced by some microorganisms. These molecules increase biodegradation of insoluble pollutants. In this study sediments and seawater samples were collected from the coastline of Bushehr provenance in the Persian Gulf and their biosurfactant producing bacteria were isolated. Biosurfactant producing bacteria were isolated by using an enrichment method in Bushnell-Hass medium with diesel oil as the sole carbon source. Five screening tests were used for selection of Biosurfactant producing bacteria: hemolysis in blood agar, oil spreading, drop collapse, emulsification activity and Bacterial Adhesion to Hydrocarbon test (BATH). These bacteria were identified using biochemical and molecular methods. Eighty different colonies were isolated from the collected samples. The most biosurfactant producing isolates related to petrochemical plants of Khark Island. Fourteen biosurfactant producing bacteria were selected between these isolates and 7 isolates were screened as these were predominant producers that belong to Shewanella alga, Shewanella upenei, Vibrio furnissii, Gallaecimonas pentaromativorans, Brevibacterium epidermidis, Psychrobacter namhaensis and Pseudomonas fluorescens. The largest clear zone diameters in oil spreading were observed for G. pentaromativorans strain O15. Also, this strain has the best emulsification activity and reduction of surface tension, suggesting it is the best of thee isolated strains. The results of this study confirmed that there is high diversity of biosurfactant producing bacteria in marine ecosystem of Iran and by application of these bacteria in petrochemical waste water environmental problems can be assisted

Study on mechanisms of biosurfactant-enhanced composting technology for waste management

Energy Technology Data Exchange (ETDEWEB)

Zhang, B.Y.; Huang, G.H.; Chen, B.; Xi, B.D.; Maqsood, I. [Regina Univ., SK (Canada)

2003-07-01

Composting is increasingly being used for solid waste treatment. The efficiency of solid waste composting might be enhanced using biosurfactants produced by microbial activities. This study was conducted to characterize the effect of biosurfactant on solid waste biodegradation throughout the composting process. The method employed involves shredding solid waste, followed by a treatment in an 8-litre (L) batch reactor. Biosurfactant production was monitored daily along with characteristics and maturity degree. Surface tension and emulsification capacity were of particular concern. The measurement of indices such as humic acid carbon (CHA) and fulvic acid carbon (CFA) were used to evaluate the maturity degree. The results indicated that the highest level of biosurfactant concentration was achieved on the third day, and within two days, related emulsification capacity reached its peak. This study confirmed the presence of biosurfactants and their function during the composting process. 16 refs., 2 tabs., 4 figs.

Optimization of biosurfactant production by Bacillus brevis using response surface methodology

Directory of Open Access Journals (Sweden)

Foukia E. Mouafi

2016-03-01

Full Text Available The present study aims to evaluate and validate a statistical model for maximizing biosurfactant productivity by Bacillus brevis using response surface methodology. In this respect, twenty bacterial isolates were screened for biosurfactant production using hemolytic activity, oil spreading technique, and emulsification index (E24. The most potent biosurfactant-producing bacterium (B. brevis was used for construction of the statistical response surface model. The optimum conditions for biosurfactant production by B. brevis were: 33 °C incubation temperature at pH 8 for 10 days incubation period and 8.5 g/L glucose concentration as a sole carbon source. The produced biosurfactant (BS (73% exhibited foaming activity, thermal stability in the range 30–80 °C for 30 min., pH stability, from 4 to 9 and antimicrobial activity against (Escherichia coli. The BS gave a good potential application as an emulsifier.

Development of More Effective Biosurfactants for Enhanced Oil Recovery

Energy Technology Data Exchange (ETDEWEB)

McInerney, J.J.; Han, S.O.; Maudgalya, S.; Mouttaki, H.; Folmsbee, M.; Knapp, R.; Nagle, D.; Jackson, B.E.; Stuadt, M.; Frey, W.

2003-01-16

The objectives of this were two fold. First, core displacement studies were done to determine whether microbial processes could recover residual oil at elevated pressures. Second, the importance of biosurfactant production for the recovery of residual oil was studies. In these studies, a biosurfactant-producing, microorganisms called Bacillus licheniformis strain JF-2 was used. This bacterium produces a cyclic peptide biosurfactant that significantly reduces the interfacial tension between oil and brine (7). The use of a mutant deficient in surfactant production and a mathematical MEOR simulator were used to determine the major mechanisms of oil recovery by these two strains.

Effect of biosurfactants on crude oil desorption and mobilization in a soil system

Energy Technology Data Exchange (ETDEWEB)

Kuyukina, M.S.; Ivshina, I.B. [Ural Branch of the Russian Academy of Sciences, Perm (Russian Federation). Institute of Ecology and Genetics of Microorganisms; Makarov, S.O.; Litvinenko, L.V. [Perm State University, Perm (Russian Federation); Cunningham, C.J. [University of Edinburgh (United Kingdom). Contaminated Land Assessment and Remediation Research Centre; Philp, J.C. [Napier University, Edinburgh (United Kingdom). School of Life Sciences

2005-02-01

Microbially produced biosurfactants were studied to enhance crude oil desorption and mobilization in model soil column systems. The ability of biosurfactants from Rhodococcus ruber to remove the oil from the soil core was 1.4-2.3 times greater than that of a synthetic surfactant of suitable properties, Tween 60. Biosurfactant-enhanced oil mobilization was temperature-related, and it was slower at 15{sup o}C than at 22-28{sup o}C. Mathematical modelling using a one-dimensional filtration model was applied to simulate the process of oil penetration through a soil column in the presence of (bio)surfactants. A strong positive correlation (R{sup 2} = 0.99) was found between surfactant penetration through oil-contaminated soil and oil removal activity. Biosurfactant was less adsorbed to soil components than synthetic surfactant, thus rapidly penetrating through the soil column and effectively removing 65-82% of crude oil. Chemical analysis showed that crude oil removed by biosurfactant contained a lower proportion of high-molecular-weight paraffins and asphaltenes, the most nonbiodegradable compounds, compared to initial oil composition. This result suggests that oil mobilized by biosurfactants could be easily biodegraded by soil bacteria. Rhodococcus biosurfactants can be used for in situ remediation of oil-contaminated soils. (author)

Production, Characterization, and Application of Bacillus licheniformis W16 Biosurfactant in Enhancing Oil Recovery.

Science.gov (United States)

Joshi, Sanket J; Al-Wahaibi, Yahya M; Al-Bahry, Saif N; Elshafie, Abdulkadir E; Al-Bemani, Ali S; Al-Bahri, Asma; Al-Mandhari, Musallam S

2016-01-01

The biosurfactant production by Bacillus licheniformis W16 and evaluation of biosurfactant based enhanced oil recovery (EOR) using core-flood under reservoir conditions were investigated. Previously reported nine different production media were screened for biosurfactant production, and two were further optimized with different carbon sources (glucose, sucrose, starch, cane molasses, or date molasses), as well as the strain was screened for biosurfactant production during the growth in different media. The biosurfactant reduced the surface tension and interfacial tension to 24.33 ± 0.57 mN m -1 and 2.47 ± 0.32 mN m -1 respectively within 72 h, at 40°C, and also altered the wettability of a hydrophobic surface by changing the contact angle from 55.67 ± 1.6 to 19.54°± 0.96°. The critical micelle dilution values of 4X were observed. The biosurfactants were characterized by different analytical techniques and identified as lipopeptide, similar to lichenysin-A. The biosurfactant was stable over wide range of extreme environmental conditions. The core flood experiments showed that the biosurfactant was able to enhance the oil recovery by 24-26% over residual oil saturation (S or ). The results highlight the potential application of lipopeptide biosurfactant in wettability alteration and microbial EOR processes.

Production, Characterization and Application of Bacillus licheniformis W16 Biosurfactant in Enhancing Oil Recovery

Directory of Open Access Journals (Sweden)

Sanket J. Joshi

2016-11-01

Full Text Available The biosurfactant production by Bacillus licheniformis W16 and evaluation of biosurfactant based enhanced oil recovery using core-flood under reservoir conditions were investigated. Previously reported nine different production media were screened for biosurfactant production, and two were further optimized with different carbon sources (glucose, sucrose, starch, cane molasses or date molasses, as well as the strain was screened for biosurfactant production during the growth in different media. The biosurfactant reduced the surface tension and interfacial tension to 24.33+0.57mN m-1 and 2.47+0.32mN m-1 respectively within 72h, at 40 C, and also altered the wettability of a hydrophobic surface by changing the contact angle from 55.67°+1.6° to 19.54°+0.96°. The critical micelle dilution values of 4X were observed. The biosurfactants were characterized by different analytical techniques and identified as lipopeptide, similar to lichenysin-A. The biosurfactant was stable over wide range of extreme environmental conditions. The core flood experiments showed that the biosurfactant was able to enhance the oil recovery by 24-26% over residual oil saturation (Sor. The results highlight the potential application of lipopeptide biosurfactant in wettability alteration and microbial enhanced oil recovery processes.

Production and applications of biosurfactant from Bacillus subtilis MUV4

Directory of Open Access Journals (Sweden)

Aran H-Kittikun

2008-04-01

Full Text Available Bacillus subtilis MUV4 produced biosurfactant in shake-flask culture (200 rpm at 30oC with modified Mckeen medium containing 1% glucose as a carbon source, 1% monosodium glutamate and 0.3% yeast extract as nitrogen sources. The supernatant of B. subtilis MUV4 reduced the surface tension of the medium from 53.50 mN/m to 33.50 mN/m after 48 h of cultivation. The yield of crude biosurfactant from B. subtilis MUV4 after precipitating the supernatant with 6N HCl was 0.652 g/L. Growth kinetics studies showed the specific growth rate (μ of 0.14 h-1, yield of biomass to substrate (Yx/s of 0.713, yield of product to substrate (Yp/s of 0.072 and yield of product to biomass (Yp/x of 0.101. Moreover, B. subtilis MUV4 produced 0.30 g/L crude biosurfactant after 96 h of cultivation in the fermentor with agitation rate of 200 rpm without aeration and uncontrolled pH condition. The crude biosurfactant was dissolved in methanol and dried by vacuum evaporator (crude methanol. The supernatant, the crude biosurfactant and the crude methanol retained the biosurfactant activity over the pH range of 1-6, 7-10 and 4-10, respectively and the emulsion stability at 24 h (E24 at pH 7 were 66.67%, 33.33% and 33.33%, respectively. The supernatant and the crude biosurfactant showed surface tension activity at 4oC, room temperature (30±2oC and 50oC after incubation for 5 h. However, only crude methanol still retained surface tension activity after 100oC for 5 h. The surface tension activity of the supernatant and the crude biosurfactant was stable in 3-10% (w/v NaCl while crude methanol showed stability in 3-20% (w/v NaCl. However, all samples lost emulsion stability when NaCl concentration was higher than 5% (w/v. With sand pack column technique, crude methanol enhanced the recovery of crude oil and kerosene oil by 41.85% and 75.00%, respectively. In hydrocarbon degradation application study, the crude biosurfactant was added to the culture medium containing 0.3% crude oil

Metagenomics for the discovery of novel biosurfactants of environmental interest from marine ecosystems.

Science.gov (United States)

Jackson, Stephen A; Borchert, Erik; O'Gara, Fergal; Dobson, Alan D W

2015-06-01

Research focused on the search for new biosurfactants aims to replace chemical surfactants, which while being cost-effective are ecologically undesirable. Metagenomics can lead to discovery of novel biosurfactants, tackling issues of low production yields. Recent successes include the heterologous production of biosurfactants. The dearth of biosurfactants discovered to date through metagenomics is puzzling given that good screening systems and heterologous host systems are available. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of biosurfactants from indigenous soil bacteria recovered from oil contaminated sites.

Science.gov (United States)

Kumar, Govind; Kumar, Rajesh; Sharma, Anita

2015-09-01

Three bacterial isolates (G1, G2 and G3) characterized as Pseudomonas plecoglossicida, Lysinibacillus fusiformis and Bacillus safensis were recovered from contaminated soil of oil refinery. These bacterial isolates produced biosurfactants in MSM medium in stationary phase. Biosurfactants were characterized on the basis of their emulsifying properties with petrol, diesel, mobil oil and petrol engine oil. Reduction in surface tension (below 40 mN m(-1)) and blood hemolysis were also included in biosurfactants characterization. Emulsification indices of G1, G2 and G3 were in the range of 98.82, 23.53 and 58.82 for petrol; 29.411,1.05 and 70.588 for diesel; 35.31, 2.93 and 17.60 for mobil oil and 35.284, 58.82 and 17.647 for petrol engine oil respectively. Dry weight of the extracted biosurfactant was 4.6, 1.4 and 2.4 g I(-1) for G1, G2 and G3 respectively. Structural analysis of the biosurfactants by Fourier Transform Infrared Spectroscopy (FTIR) revealed significant differences in the bonding pattern of individual biosurfactant.

Production of Biosurfactants by Pseudomonas Species for Application in the Petroleum Industry.

Science.gov (United States)

Silva, Maria Aparecida M; Silva, Aline F; Rufino, Raquel D; Luna, Juliana M; Santos, Valdemir A; Sarubbo, Leonie A

2017-02-01

  The production of surfactants by microorganisms has become an attractive option in the treatment of oil-contaminated environments because biosurfactants are biodegradable and less toxic than synthetic surfactants, although production costs remain high. With the aim of reducing the cost of biosurfactant production, three strains of Pseudomonas (designated P1, P2, and P3) were cultivated in a low-cost medium containing molasses and corn steep liquor as substrates. Following the selection of the best producer (P3), a rotational central composite design (RCCD) was used to determine the influence of substrates concentration on surface tension and biosurfactant yield. The biosurfactant reduced the surface tension of water to 27.5 mN/m, and its CMC was determined to be 600 mg/L. The yield was 4.0 g/L. The biosurfactant demonstrated applicability under specific environmental conditions and was able to remove 80 to 90% of motor oil adsorbed to sand. The properties of the biosurfactant suggest its potential application in bioremediation of hydrophobic pollutants.

Production and characterization of biosurfactant produced by a novel Pseudomonas sp. 2B.

Science.gov (United States)

Aparna, A; Srinikethan, G; Smitha, H

2012-06-15

Biosurfactant-producing bacteria were isolated from terrestrial samples collected in areas contaminated with petroleum compounds. Isolates were screened for biosurfactant production using Cetyl Tri Ammonium Bromide (CTAB)-Methylene blue agar selection medium and the qualitative drop-collapse test. An efficient bacterial strain was selected based on rapid drop collapse activity and highest biosurfactant production. The biochemical characteristics and partial sequenced 16S rRNA gene of isolate, 2B, identified the bacterium as Pseudomonas sp. Five different low cost carbon substrates were evaluated for their effect on biosurfactant production. The maximum biosurfactant synthesis (4.97 g/L) occurred at 96 h when the cells were grown on modified PPGAS medium containing 1% (v/v) molasses at 30 °C and 150 rpm. The cell free broth containing the biosurfactant could reduce the surface tension to 30.14 mN/m. The surface active compound showed emulsifying activity against a variety of hydrocarbons and achieved a maximum emulsion index of 84% for sunflower oil. Compositional analysis of the biosurfactant reveals that the extracted biosurfactant was a glycolipid type, which was composed of high percentages of lipid (∼65%, w/w) and carbohydrate (∼32%, w/w). Fourier transform infrared (FT-IR) spectrum of extracted biosurfactant indicates the presence of carboxyl, hydroxyl and methoxyl functional groups. The mass spectra (MS) shows that dirhamnolipid (l-rhamnopyranosyl-l-rhamnopyranosyl-3-hydroxydecanoyl-3-hydroxydecanoate, Rha-Rha-C(10)-C(10)) was detected in abundance with the predominant congener monorhamnolipid (l-rhamnopyranosyl-β-hydroxydecanoyl-β-hydroxydecanoate, Rha-C(10)-C(10)). The crude oil recovery studies using the biosurfactant produced by Pseudomonas sp. 2B suggested its potential application in microbial enhanced oil recovery and bioremediation. Copyright © 2012 Elsevier B.V. All rights reserved.

PRODUCTION AND CHARACTERIZATION OF BIOSURFACTANT BY Pseudomonas fluorescens USING CASSAVA FLOUR WASTEWATER AS MEDIA

Directory of Open Access Journals (Sweden)

Venty Suryanti

2013-12-01

Full Text Available Biosurfactant with efficient emulsification properties could be produced by Pseudomonas flourescens using cassava flour wastewater (manipueira as media. The ability of P. flourescens to produce biosurfactant could suggest potential use in industrial and environmental applications. Media containing a mixture of natural manipueira and nutrient broth with 48 h fermentation was the optimum condition for the biosurfactant production. Based on UV-Vis and FT-IR spectra, the biosurfactant was indicated as rhamnolipids containing hydroxyl, ester, carboxylic and aliphatic carbon chain functional groups. Biosurfactant exhibited critical micelle concentration (CMC value of 715 mg/L and reduced the surface tension of the water from 80 mN/m to 59 mN/m. The biosurfactant was able to decrease the interfacial tension about 51-70% when benzyl chloride, palm oil and kerosene were used as water-immiscible compounds. The biosurfactant was able to form stable emulsion until 30 days when paraffin, soybean oil, lubricant oil and kerosene were used as water-immiscible compounds.

Synthesis of rhamnolipid biosurfactant and mode of hexadecane uptake by Pseudomonas species

Directory of Open Access Journals (Sweden)

Singh Pooja

2009-03-01

Full Text Available Abstract Background Microorganisms have devised ways by which they increase the bioavailability of many water immiscible substrates whose degradation rates are limited by their low water solubility. Hexadecane is one such water immiscible hydrocarbon substrate which forms an important constituent of oil. One major mechanism employed by hydrocarbon degrading organisms to utilize such substrates is the production of biosurfactants. However, much of the overall mechanism by which such organisms utilize hydrocarbon substrate still remains a mystery. Results With an aim to gain more insight into hydrocarbon uptake mechanism, an efficient biosurfactant producing and n-hexadecane utilizing Pseudomonas sp was isolated from oil contaminated soil which was found to produce rhamnolipid type of biosurfactant containing a total of 13 congeners. Biosurfactant action brought about the dispersion of hexadecane to droplets smaller than 0.22 μm increasing the availability of the hydrocarbon to the degrading organism. Involvement of biosurfactant was further confirmed by electron microscopic studies. Biosurfactant formed an emulsion with hexadecane thereby facilitating increased contact between hydrocarbon and the degrading bacteria. Interestingly, it was observed that "internalization" of "biosurfactant layered hydrocarbon droplet" was taking place suggesting a mechanism similar in appearance to active pinocytosis, a fact not earlier visually reported in bacterial systems for hydrocarbon uptake. Conclusion This study throws more light on the uptake mechanism of hydrocarbon by Pseudomonas aeruginosa. We report here a new and exciting line of research for hydrocarbon uptake involving internalization of biosurfactant covered hydrocarbon inside cell for subsequent breakdown.

Biosurfactant production by Bacillus subtilis B30 and its application in enhancing oil recovery.

Science.gov (United States)

Al-Wahaibi, Yahya; Joshi, Sanket; Al-Bahry, Saif; Elshafie, Abdulkadir; Al-Bemani, Ali; Shibulal, Biji

2014-02-01

The fermentative production of biosurfactants by Bacillus subtilis strain B30 and the evaluation of biosurfactant based enhanced oil recovery using core-flood were investigated. Different carbon sources (glucose, sucrose, starch, date molasses, cane molasses) were tested to determine the optimal biosurfactant production. The isolate B30 produced a biosurfactant that could reduce the surface tension and interfacial tension to 26.63±0.45 mN/m and 3.79±0.27 mN/m, respectively in less than 12h in both glucose or date molasses based media. A crude biosurfactant concentration of 0.3-0.5 g/l and critical micelle dilution (CMD) values of 1:8 were observed. The biosurfactants gave stable emulsions with wide range of hydrocarbons including light and heavy crude oil. The biosurfactants were partially purified and identified as a mixture of lipopeptides similar to surfactin, using high performance thin layer chromatography and Fourier transform infrared spectroscopy. The biosurfactants were stable over wide range of pH, salinity and temperatures. The crude biosurfactant preparation enhanced light oil recovery by 17-26% and heavy oil recovery by 31% in core-flood studies. The results are indicative of the potential of the strain for the development of ex situ microbial enhanced oil recovery processes using glucose or date molasses based minimal media. Copyright © 2013 Elsevier B.V. All rights reserved.

Biosurfactant production by Pseudomonas fluorescens growing on molasses and its application in phenol degradation

Science.gov (United States)

Suryantia, Venty; Marliyana, Soerya Dewi; Wulandari, Astri

2015-12-01

A molasses based medium for the biosurfactant production by Pseudomonas fluorescens was developed, where the effect of pre-treated of molasses and medium composition were evaluated. Biosurfactant production was followed by measuring optical density (OD), surface tension and emulsifying index (E24) over 12 days of fermentation. The optimum condition for the biosurfactant production was obtained when a medium containing of 8 g/L nutrient broth, 5 g/L NaCl, 1 g/L NH4NO3 and 5% v/v pre-treated molasses with centrifugation was used as media with 3 days of fermentation. The biosurfactant was identified as a rhamnolipid type biosurfactant which had critical micelle concentration (CMC) value of 801 mg/L and was able to reduce the surface tension of the water from 80 mN/m to 51 mN/m. The biosurfactants had water in oil (w/o) emulsion type. Biosurfactant was able to emulsify various hydrocarbons, which were able to decrase the interfacial tension about 50-75% when benzyl chloride, anisaldehyde and palm oil were used as immiscible compounds. The biosurfactant exhibited the E24 value of about 50% and the stable emulsion was reached up to 30 days when lubricant was used as an immiscible compound. Up to 68% of phenol was degraded in the presence of biosurfactant within 15 days, whereas only 56% of phenol was degraded in the absence of biosurfactant. Overall, the results exhibited that molasses are recommended for the rhamnolipids production which possessed good surface-active properties and had potential application in the enhancement of phenol degradation.

Multiple roles of biosurfactants in structural biofilm development by Pseudomonas aeruginosa

DEFF Research Database (Denmark)

Pamp, Sünje Johanna; Tolker-Nielsen, Tim

2007-01-01

Recent studies have indicated that biosurfactants produced by Pseudomonas aeruginosa play a role both in maintaining channels between multicellular structures in biofilms and in dispersal of cells from biofilms. Through the use of flow cell technology and enhanced confocal laser scanning microscopy......, we have obtained results which suggest that the biosurfactants produced by P. aeruginosa play additional roles in structural biofilm development. We present genetic evidence that during biofilm development by P. aeruginosa, biosurfactants promote microcolony formation in the initial phase...... and facilitate migration-dependent structural development in the later phase. P. aeruginosa rhl4 mutants, deficient in synthesis of biosurfactants, were not capable of forming microcolonies in the initial phase of biofilm formation. Experiments involving two-color-coded mixed-strain biofilms showed that P...

Utilization of agroindustrial waste for biosurfactant production by native bacteria from chiapas

Directory of Open Access Journals (Sweden)

Yañez-Ocampo Gustavo

2017-02-01

Full Text Available In this work, two agro-industrial wastes, namely Waste Cooking Oil (WCO and Coffee Wastewater (CW have been used as the carbon source for the production of biosurfactants, due to their low cost and high availability. Biosurfactant-producing bacterial isolates from the Mexican state of Chiapas were used. The selected biosurfactant-producer strains were evaluated in a liquid medium with 2% (v/v of WCO as the carbon source. The assay was conducted in an Erlenmeyer flask containing 300 mL aliquots of mineral salt media (MSM + residue and incubated at 100 rpm at room temperature for 96 hours. The biosurfactant produced in the samples reduced the surface tension from 50 to 30-29 mN/m. Strains A and 83 showed the maximum emulsification index at 58-59%. Strain A showed the highest biosurfactant yield with a production of 3.7 g/L in comparison with strains B, 83 and Pseudomonas aeruginosa ATCC27853. Our results suggest that the biosurfactant produced by strain A has great potential in the treatment of wastewater with a high content of fatty acids, and of soils contaminated by pesticides or oil hydrocarbons.

Biosurfactant-biopolymer driven microbial enhanced oil recovery (MEOR) and its optimization by an ANN-GA hybrid technique.

Science.gov (United States)

Dhanarajan, Gunaseelan; Rangarajan, Vivek; Bandi, Chandrakanth; Dixit, Abhivyakti; Das, Susmita; Ale, Kranthikiran; Sen, Ramkrishna

2017-08-20

A lipopeptide biosurfactant produced by marine Bacillus megaterium and a biopolymer produced by thermophilic Bacillus licheniformis were tested for their application potential in the enhanced oil recovery. The crude biosurfactant obtained after acid precipitation effectively reduced the surface tension of deionized water from 70.5 to 28.25mN/m and the interfacial tension between lube oil and water from 18.6 to 1.5mN/m at a concentration of 250mgL -1 . The biosurfactant exhibited a maximum emulsification activity (E 24 ) of 81.66% against lube oil. The lipopeptide micelles were stabilized by addition of Ca 2+ ions to the biosurfactant solution. The oil recovery efficiency of Ca 2+ conditioned lipopeptide solution from a sand-packed column was optimized by using artificial neural network (ANN) modelling coupled with genetic algorithm (GA) optimization. Three important parameters namely lipopeptide concentration, Ca 2+ concentration and solution pH were considered for optimization studies. In order to further improve the recovery efficiency, a water soluble biopolymer produced by Bacillus licheniformis was used as a flooding agent after biosurfactant incubation. Upon ANN-GA optimization, 45% tertiary oil recovery was achieved, when biopolymer at a concentration of 3gL -1 was used as a flooding agent. Oil recovery was only 29% at optimal conditions predicted by ANN-GA, when only water was used as flooding solution. The important characteristics of biopolymers such as its viscosity, pore plugging capabilities and bio-cementing ability have also been tested. Thus, as a result of biosurfactant incubation and biopolymer flooding under the optimal process conditions, a maximum oil recovery of 45% was achieved. Therefore, this study is novel, timely and interesting for it showed the combined influence of biosurfactant and biopolymer on solubilisation and mobilization of oil from the soil. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of gamma-irradiation pretreatment on improvement of anaerobic digestive characteristic of sludge

International Nuclear Information System (INIS)

Mou Yanyan; Yuan Shoujun; Yu Xin; Zheng Zheng; Cui Lei; Zhao Yongfu

2005-01-01

A comparative study was made about main anaerobic digestive characteristics of sludge which was subjected to a 60 Co gamma-irradiation pretreatment. The results showed the gamma-irradiation pretreatment can clearly improve anaerobic digestibility of sludge and pick up the anaerobic digestion speed of sludge. (authors)

Characterization and emulsification properties of rhamnolipid and sophorolipid biosurfactants and their applications.

Science.gov (United States)

Nguyen, Thu T; Sabatini, David A

2011-02-18

Due to their non-toxic nature, biodegradability and production from renewable resources, research has shown an increasing interest in the use of biosurfactants in a wide variety of applications. This paper reviews the characterization of rhamnolipid and sophorolipid biosurfactants based on their hydrophilicity/hydrophobicity and their ability to form microemulsions with a range of oils without additives. The use of the biosurfactants in applications such as detergency and vegetable oil extraction for biodiesel application is also discussed. Rhamnolipid was found to be a hydrophilic surfactant while sophorolipid was found to be very hydrophobic. Therefore, rhamnolipid and sophorolipid biosurfactants in mixtures showed robust performance in these applications.

Characterization and Emulsification Properties of Rhamnolipid and Sophorolipid Biosurfactants and Their Applications

Directory of Open Access Journals (Sweden)

Thu T. Nguyen

2011-02-01

Full Text Available Due to their non-toxic nature, biodegradability and production from renewable resources, research has shown an increasing interest in the use of biosurfactants in a wide variety of applications. This paper reviews the characterization of rhamnolipid and sophorolipid biosurfactants based on their hydrophilicity/hydrophobicity and their ability to form microemulsions with a range of oils without additives. The use of the biosurfactants in applications such as detergency and vegetable oil extraction for biodiesel application is also discussed. Rhamnolipid was found to be a hydrophilic surfactant while sophorolipid was found to be very hydrophobic. Therefore, rhamnolipid and sophorolipid biosurfactants in mixtures showed robust performance in these applications.

Biosurfactant-enhanced soil bioremediation

Energy Technology Data Exchange (ETDEWEB)

Kosaric, N.; Lu, G.; Velikonja, J. [Univ. of Western Ontario, London, Ontario (Canada)

1995-12-01

Bioremediation of soil contaminated with organic chemicals is a viable alternative method for clean-up and remedy of hazardous waste sites. The final objective in this approach is to convert the parent toxicant into a readily biodegradable product which is harmless to human health and/or the environment. Biodegradation of hydrocarbons in soil can also efficiently be enhanced by addition or in-situ production of biosufactants. It was generally observed that the degradation time was shortened and particularly the adaptation time for the microbes. More data from our laboratories showed that chlorinated aromatic compounds, such as 2,4-dichlorophenol, a herbicide Metolachlor, as well as naphthalene are degraded faster and more completely when selected biosurfactants are added to the soil. More recent data demonstrated an enhanced biodegradation of heavy hydrocarbons in petrochemical sludges, and in contaminated oil when biosurfactants were present or were added prior to the biodegradation process.

Predicting the minimum liquid surface tension activity of pseudomonads expressing biosurfactants.

Science.gov (United States)

Mohammed, I U; Deeni, Y; Hapca, S M; McLaughlin, K; Spiers, A J

2015-01-01

Bacteria produce a variety of biosurfactants capable of significantly reducing liquid (aqueous) surface tension (γ) with a range of biological roles and biotechnological uses. To determine the lowest achievable surface tension (γMin ), we tested a diverse collection of Pseudomonas-like isolates from contaminated soil and activated sludge and identified those expressing biosurfactants by drop-collapse assay. Liquid surface tension-reducing ability was quantitatively determined by tensiometry, with 57 isolates found to significantly lower culture supernatant surface tensions to 24·5-49·1 mN m(-1) . Differences in biosurfactant behaviour determined by foaming, emulsion and oil-displacement assays were also observed amongst isolates producing surface tensions of 25-27 mN m(-1) , suggesting that a range of structurally diverse biosurfactants were being expressed. Individual distribution identification (IDI) analysis was used to identify the theoretical probability distribution that best fitted the surface tension data, which predicted a γMin of 24·24 mN m(-1) . This was in agreement with predictions based on earlier work of published mixed bacterial spp. data, suggesting a fundamental limit to the ability of bacterial biosurfactants to reduce surface tensions in aqueous systems. This implies a biological restriction on the synthesis and export of these agents or a physical-chemical restriction on their functioning once produced. Numerous surveys of biosurfactant-producing bacteria have been conducted, but only recently has an attempt been made to predict the minimum liquid surface tension these surface-active agents can achieve. Here, we determine a theoretical minimum of 24 mN m(-1) by statistical analysis of tensiometry data, suggesting a fundamental limit for biosurfactant activity in bacterial cultures incubated under standard growth conditions. This raises a challenge to our understanding of biosurfactant expression, secretion and function, as well as

Isolation and characterization of biosurfactant producing bacteria from Persian Gulf (Bushehr provenance).

Science.gov (United States)

Hassanshahian, Mehdi

2014-09-15

Biosurfactants are surface active materials that are produced by some microorganisms. These molecules increase biodegradation of insoluble pollutants. In this study sediments and seawater samples were collected from the coastline of Bushehr provenance in the Persian Gulf and their biosurfactant producing bacteria were isolated. Biosurfactant producing bacteria were isolated by using an enrichment method in Bushnell-Hass medium with diesel oil as the sole carbon source. Five screening tests were used for selection of Biosurfactant producing bacteria: hemolysis in blood agar, oil spreading, drop collapse, emulsification activity and Bacterial Adhesion to Hydrocarbon test (BATH). These bacteria were identified using biochemical and molecular methods. Eighty different colonies were isolated from the collected samples. The most biosurfactant producing isolates related to petrochemical plants of Khark Island. Fourteen biosurfactant producing bacteria were selected between these isolates and 7 isolates were screened as these were predominant producers that belong to Shewanella alga, Shewanella upenei, Vibrio furnissii, Gallaecimonas pentaromativorans, Brevibacterium epidermidis, Psychrobacter namhaensis and Pseudomonas fluorescens. The largest clear zone diameters in oil spreading were observed for G. pentaromativorans strain O15. Also, this strain has the best emulsification activity and reduction of surface tension, suggesting it is the best of thee isolated strains. The results of this study confirmed that there is high diversity of biosurfactant producing bacteria in marine ecosystem of Iran and by application of these bacteria in petrochemical waste water environmental problems can be assisted. Copyright © 2014 Elsevier Ltd. All rights reserved.

Application of biosurfactants in environmental biotechnology; remediation of oil and heavy metal

Directory of Open Access Journals (Sweden)

Ahmad Fahim Mahmud

2016-07-01

Full Text Available Many toxic substances have been introduced into environment through human activities. These compounds are danger to human health when they are ultimately or immediately in contact with soil particles. A conventional method to reduce, degrade and remove these substances is associated with some risk. In recent years, microorganisms have proved a unique role in the degradation and detoxification of polluted soil and water environments and, this process has been termed bio reclamation. The diversity of bioemulsifiers/biosurfactants makes them an attractive group and important key roles in various fields of industrial as well as biotechnological applications such as enhanced oil recovery, biodegradation of pollutants, and pharmaceutics. Environmental application of microbial surfactant has been shown as a promising due to solubilization of low solubility compounds, low toxicity observed and efficacy in improving biodegradation. However, it is important to note that full scale tests and more information is require to predict the behavior and model of surfactant function on the remediation process with biosurfactants. The purpose of this review is to describe the state of art in the potential applications of biosurfactants in remediation of environmental pollution caused by oil and heavy metal.

Rhamnolipid biosurfactants: evolutionary implications, applications and future prospects from untapped marine resource.

Science.gov (United States)

Kiran, George Seghal; Ninawe, Arun Shivanth; Lipton, Anuj Nishanth; Pandian, Vijayalakshmi; Selvin, Joseph

2016-01-01

Rhamnolipid-biosurfactants are known to be produced by the genus Pseudomonas, however recent literature reported that rhamnolipids (RLs) are distributed among diverse microbial genera. To integrate the evolutionary implications of rhamnosyl transferase among various groups of microorganisms, a comprehensive comparative motif analysis was performed amongst bacterial producers. Findings on new RL-producing microorganism is helpful from a biotechnological perspective and to replace infective P. aeruginosa strains which ultimately ensure industrially safe production of RLs. Halotolerant biosurfactants are required for efficient bioremediation of marine oil spills. An insight on the exploitation of marine microbes as the potential source of RL biosurfactants is highlighted in the present review. An economic production process, solid-state fermentation using agro-industrial and industrial waste would increase the scope of biosurfactants commercialization. Potential and prospective applications of RL-biosurfactants including hydrocarbon bioremediation, heavy metal removal, antibiofilm activity/biofilm disruption and greener synthesis of nanoparticles are highlighted in this review.

Staphylococcus haemolyticus as a potential producer of biosurfactants with antimicrobial, anti-adhesive and synergistic properties.

Science.gov (United States)

Rossi, C C; Santos-Gandelman, J F; Barros, E M; Alvarez, V M; Laport, M S; Giambiagi-deMarval, M

2016-09-01

Staphylococcus haemolyticus is an opportunistic human pathogen that usually gains entry into the host tissue in association with medical device contamination. Biofilm formation is a key factor for the establishment of this bacterium and its arrangement and dynamics can be influenced by the synthesis of biosurfactants. Biosurfactants are structurally diverse amphiphilic molecules with versatile biotechnological applications, but information on their production by staphylococci is still scarce. In this work, two Staph. haemolyticus strains, showing high potential for biosurfactant production - as observed by four complementary methods - were investigated. Biosurfactant extracts were produced and studied for their capacity to inhibit the growth and biofilm formation by other bacterial human pathogens. The biosurfactant produced by the one of the strains inhibited the growth of most bacteria tested and subinhibitory concentrations of the biosurfactant were able to decrease biofilm formation and showed synergistic effects with tetracycline. Because these results were also positive when the biosurfactants were tested against the producing strains, it is likely that biosurfactant production by Staph. haemolyticus may be an unexplored virulence factor, important for competition and biofilm formation by the bacterium, in addition to the biotechnological potential. This work is the first to show the production of biosurfactants by Staphylococcus haemolyticus strains. Extracts showed antimicrobial, anti-adhesive and synergistic properties against a variety of relevant human pathogens, including the producing strains. In addition to the biotechnological potential, biosurfactants produced by Staph. haemolyticus are potentially undescribed virulence determinants in their producing strains. © 2016 The Society for Applied Microbiology.

Biosurfactant Producing Microbes from Oil Contaminated Soil - Isolation, Screening and Characterization

OpenAIRE

, A Pandey; , D Nandi; , N Prasad; , S Arora

2016-01-01

Th1s paper bas1cally deals W1th 1solat10n, productıon and characterızatıon of biosurfactant producing microbes from oil contaminated soil sample. In this paper, we are comparing and discussing different methods to screen & characterize microbes from soil which can degrade oil due to their biosurfactant producing activity which helps in reduction of surface tension of oil. Oils used to check the biosurfactant activity of microbes, were engine oil and vegetable oil. Further isolation of...

Isolation and functional characterization of a biosurfactant produced by Lactobacillus paracasei

OpenAIRE

Gudiña, Eduardo J.; Teixeira, J. A.; Rodrigues, L. R.

2010-01-01

In this study, the crude biosurfactant produced by a Lactobacillus paracasei strain isolated in a Portuguese dairy industry was characterized. The minimum surface tension (41.8mN/m) and the critical micelle concentration (2.5 mg/ml) obtained were found to be similar to the values previously reported for biosurfactants isolated from other lactobacilli. The biosurfactant was found to be stable to pH changes over a range from 6 to 10, being more effective at pH 7, and showed no loss ...

Biosurfactant production by Pseudomonas sp. and its role in aqueous phase partitioning and biodegradation of chlorpyrifos.

Science.gov (United States)

Singh, P B; Sharma, S; Saini, H S; Chadha, B S

2009-09-01

To study the effect of biosurfactant on aqueous phase solubility and biodegradation of chlorpyrifos. A Pseudomonas sp. (ChlD), isolated from agricultural soil by enrichment culture technique in the presence of chlorpyrifos, was capable of producing biosurfactant (rhamnolipids) and degrading chlorpyrifos (0.01 g l(-1)). The partially purified rhamnolipid biosurfactant preparation, having a CMC of 0.2 g l(-1), was evaluated for its ability to enhance aqueous phase partitioning and degradation of chlorpyrifos (0.01 g l(-1)) by ChlD strain. The best degradation efficiency was observed at 0.1 g l(-1) supplement of biosurfactant, as validated by GC and HPLC studies. The addition of biosurfactant at 0.1 g l(-1) resulted in more than 98% degradation of chlorpyrifos when compared to 84% in the absence of biosurfactant after 120-h incubation. This first report, to the best of our knowledge, on enhanced degradation of chlorpyrifos in the presence of biosurfactant(s), would help in developing bioremediation protocols to counter accumulation of organophosphates to toxic/carcinogenic levels in environment.

Trehalolipid biosurfactants from nonpathogenic Rhodococcus actinobacteria with diverse immunomodulatory activities.

Science.gov (United States)

Kuyukina, Maria S; Ivshina, Irena B; Baeva, Tatiana A; Kochina, Olesia A; Gein, Sergey V; Chereshnev, Valery A

2015-12-25

Actinobacteria of the genus Rhodococcus produce trehalolipid biosurfactants with versatile biochemical properties and low toxicity. In recent years, these biosurfactants are increasingly studied as possible biomedical agents with expressed immunological activities. Applications of trehalolipids from Rhodococcus, predominantly cell-bound, in biomedicine are also attractive because their cost drawback could be less significant for high-value products. The review summarizes recent findings in immunomodulatory activities of trehalolipid biosurfactants from nonpathogenic Rhodococcus and related actinobacteria and compares their biomedical potential with well-known immunomodifying properties of trehalose dimycolates from Mycobacterium tuberculosis. Molecular mechanisms of trehalolipid interactions with immunocompetent cells are also discussed. Copyright © 2015. Published by Elsevier B.V.

Isolation and characterization of a biosurfactant-producing Fusarium sp. BS-8 from oil contaminated soil.

Science.gov (United States)

Qazi, Muneer A; Kanwal, Tayyaba; Jadoon, Muniba; Ahmed, Safia; Fatima, Nighat

2014-01-01

This study reports characterization of a biosurfactant-producing fungal isolate from oil contaminated soil of Missa Keswal oil field, Pakistan. It was identified as Fusarium sp. BS-8 on the basis of macroscopic and microscopic morphology, and 18S rDNA gene sequence homology. The biosurfactant-producing capability of the fungal isolates was screened using oil displacement activity, emulsification index assay, and surface tension (SFT) measurement. The optimization of operational parameters and culture conditions resulted in maximum biosurfactant production using 9% (v/v) inoculum at 30°C, pH 7.0, using sucrose and yeast extract, as carbon and nitrogen sources, respectively. A C:N ratio of 0.9:0.1 (w/w) was found to be optimum for growth and biosurfactant production. At optimal conditions, it attained lowest SFT (i.e., 32 mN m(-1) ) with a critical micelle concentration of ≥ 1.2 mg mL(-1) . During 5 L shake flask fermentation experiments, the biosurfactant productivity was 1.21 g L(-1) pure biosurfactant having significant emulsifying index (E24 , 70%) and oil-displacing activity (16 mm). Thin layer chromatography and Fourier transform infrared spectrometric analyses indicated a lipopeptide type of the biosurfactant. The Fusarium sp. BS-8 has substantial potential of biosurfactant production, yet it needs to be fully characterized with possibility of relatively new class of biosurfactants. © 2014 American Institute of Chemical Engineers.

Response surface optimization of biosurfactant produced by Pseudomonas aeruginosa MA01 isolated from spoiled apples.

Science.gov (United States)

Abbasi, Habib; Sharafi, Hakimeh; Alidost, Leila; Bodagh, Atefe; Zahiri, Hossein Shahbani; Noghabi, Kambiz Akbari

2013-01-01

A potent biosurfactant-producing bacterial strain isolated from spoiled apples was identified by 16S rRNA as Pseudomonas aeruginosa MA01. Compositional analysis revealed that the extracted biosurfactant was composed of high percentages of lipid (66%, w/w) and carbohydrate (32%, w/w). The surface tension of pure water decreased gradually with increasing biosurfactant concentration to 32.5 mN m(-1) with critical micelle concentration (CMC) value of 10.1 mg L(-1). The Fourier transform infrared spectrum of extracted biosurfactant confirmed the glycolipid nature of this natural product. Response surface methodology (RSM) was employed to optimize the biosynthesis medium for the production of MA01 biosurfactant. Nineteen carbon sources and 11 nitrogen sources were examined, with soybean oil and sodium nitrate being the most effective carbon and nitrogen sources on biosurfactant production, respectively. Among the organic nitrogen sources examined, yeast extract was necessary as a complementary nitrogen source for high production yield. Biosurfactant production at the optimum value of fermentation processing factor (15.68 g/L) was 29.5% higher than the biosurfactant concentration obtained before the RSM optimization (12.1 g/L). A central composite design algorithm was used to optimize the levels of key medium components, and it was concluded that two stages of optimization using RSM could increase biosurfactant production by 1.46 times, as compared to the values obtained before optimization.

Efficiency of lipopeptide biosurfactants in removal of petroleum hydrocarbons and heavy metals from contaminated soil.

Science.gov (United States)

Singh, Anil Kumar; Cameotra, Swaranjit Singh

2013-10-01

This study describes the potential application of lipopeptide biosurfactants in removal of petroleum hydrocarbons and heavy metals from the soil samples collected from industrial dumping site. High concentrations of heavy metals (like iron, lead, nickel, cadmium, copper, cobalt and zinc) and petroleum hydrocarbons were present in the contaminated soil samples. Lipopeptide biosurfactant, consisting of surfactin and fengycin was obtained from Bacillus subtilis A21. Soil washing with biosurfactant solution removed significant amount of petroleum hydrocarbon (64.5 %) and metals namely cadmium (44.2 %), cobalt (35.4 %), lead (40.3 %), nickel (32.2 %), copper (26.2 %) and zinc (32.07 %). Parameters like surfactant concentration, temperature, agitation condition and pH of the washing solution influenced the pollutant removing ability of biosurfactant mixture. Biosurfactant exhibited substantial hydrocarbon solubility above its critical micelle concentration. During washing, 50 % of biosurfactant was sorbed to the soil particles decreasing effective concentration during washing process. Biosurfactant washed soil exhibited 100 % mustard seed germination contradictory to water washed soil where no germination was observed. The results indicate that the soil washing with mixture of lipopeptide biosurfactants at concentrations above its critical micelle concentration can be an efficient and environment friendly approach for removing pollutants (petroleum hydrocarbon and heavy metals) from contaminated soil.

Anaerobic biodegradation of fluoranthene under methanogenic conditions in presence of surface-active compounds

DEFF Research Database (Denmark)

Fuchedzhieva, Nadezhda; Karakashev, Dimitar Borisov; Angelidaki, Irini

2008-01-01

for the study were linear alkyl benzene sulphonates (LAS) and rhamnolipid-biosurfactant complex from Pseudomonas sp. PS-17. Biodegradation of fluoranthene was monitored by GC/MS for a period up to 12th day. No change in the fluoranthene concentration was registered after 7th day. The presence of LAS enhanced...... biodegradation was most likely as a result of the increased fluoranthene solubility. The results indicate that LAS can be considered as a promising agent for facilitation of the process of anaerobic polycyclic aromatic hydrocarbons (PAH) biodegradation under methanogenic conditions....

Improvement of anaerobic digestion of sludge

Energy Technology Data Exchange (ETDEWEB)

Dohanyos, Michael; Zabranska, Jana; Kutil, Josef; Jenicek, Pavel

2003-07-01

Anaerobic digestion improvement can be accomplished by different methods. Besides optimization of process conditions is frequently used pretreatment of input sludge and increase of process temperature. Thermophilic process brings a higher solids reduction and biogas production, the high resistance to foaming, no problems with odour, the higher effect of destroying pathogens and the improvement of the energy balance of the whole treatment plant. Disintegration of excess activated sludge in lysate centrifuge was proved in full-scale conditions causing increase of biogas production. The rapid thermal conditioning of digested sludge is acceptable method of particulate matter disintegration and solubilization. (author)

Simultaneous production of lipases and biosurfactants by submerged and solid-state bioprocesses.

Science.gov (United States)

Colla, Luciane Maria; Rizzardi, Juliana; Pinto, Marta Heidtmann; Reinehr, Christian Oliveira; Bertolin, Telma Elita; Costa, Jorge Alberto Vieira

2010-11-01

Lipases and biosurfactants are compounds produced by microorganisms generally involved in the metabolization of oil substrates. However, the relationship between the production of lipases and biosurfactants has not been established yet. Therefore, this study aimed to evaluate the correlation between production of lipases and biosurfactants by submerged (SmgB) and solid-state bioprocess (SSB) using Aspergillus spp., which were isolated from a soil contaminated by diesel oil. SSB had the highest production of lipases, with lipolytic activities of 25.22U, while SmgB had 4.52U. The production of biosurfactants was not observed in the SSB. In the SmgB, correlation coefficients of 91% and 87% were obtained between lipolytic activity and oil in water and water in oil emulsifying activities, respectively. A correlation of 84% was obtained between lipolytic activity and reduction of surface tension in the culture medium. The surface tension decreased from 50 to 28mNm(-1) indicating that biosurfactants were produced in the culture medium. Copyright 2010 Elsevier Ltd. All rights reserved.

Isolation of biosurfactant producing bacteria from petroleum contaminated sites and their characterization

Directory of Open Access Journals (Sweden)

Rida Batool

2017-05-01

Full Text Available Biosurfactants are microbial amphiphilic compounds which can reduce surface tension between aqueous and hydrocarbon mixtures. Bacterial strains isolated from petroleum contaminated soil of various motor workshops were characterized morphologically and biochemically. Biosurfactant producing ability of the strains was determined and their emulsification activity was screened against different oils. All the selected bacterial strains showed enhanced biosurfactants production with yeast extract as nitrogen source and glucose as carbon source at optimized conditions. These strains also exhibited multiple metal and antibiotics resistance. Isolated biosurfactants of three most promising strains SF-1, SF-4 and SM-1 were extracted by solvent extraction and subjected to TLC technique. The technique indicates the glycolipid nature of the compounds and presence of rhamnose sugar, which was further confirmed by FT-IR analysis. 16srRNA analysis revealed that SF-1 and SM-1 had close resemblance with Pseudomonas sp. while SF-4 showed homology with Enterobacter sp. Isolation and screening of biosurfactant producing strains from petroleum polluted places proved to be a quick and effective means to find bacterial strains with possible industrial uses.

Rhamnolipid biosurfactant against Fusarium sacchari--the causal organism of pokkah boeng disease of sugarcane.

Science.gov (United States)

Goswami, Debahuti; Handique, Pratap Jyoti; Deka, Suresh

2014-06-01

Pokkah boeng disease on sugarcane caused by the fungus Fusarium sacchari results considerable damage to the crop leading to top rot, the most serious and advanced stage of pokkah boeng, where the growing point is killed and the entire top of the plant dies. In the present study, the effect of rhamnolipid biosurfactant as an antifungal agent against F. sacchari to control pokkah boeng disease was investigated. On the basis of surface tension reduction, 12 bacterial isolates were selected as potent biosurfactant producers and eight of them showed antagonistic effect against F. sacchari. Among the eight, the isolate DS9 was found as the effective inhibitor of the fungus in vitro which was further evaluated using its biosurfactant present in whole culture, cell-free culture supernatant and crude biosurfactant at various concentrations. Reductions of fungal growths were found more with crude biosurfactant. By sequencing 16S rRNA, DS9 was identified as P. aeruginosa and the produced biosurfactant was characterized as rhamnolipid by Liquid Chromatography-Mass Spectrometry (LC-MS) analysis. The rhamnolipid biosurfactant inhibits phytopathogenic fungi F. sacchari and therefore seems to be a good biocontrol agent to control pokkah boeng disease of sugarcane. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Biosurfactant production by Rhodococcus erythropolis and its application to oil removal

Directory of Open Access Journals (Sweden)

Graziela Jardim Pacheco

2010-10-01

Full Text Available The influence of different nutrients on biosurfactant production by Rhodococcus erythropolis was investigated. Increasing the concentration of phosphate buffer from 30 up through 150 mmol/L stimulated an increase in biosurfactant production, which reached a maximum concentration of 285 mg/L in shaken flasks. Statistical analysis showed that glycerol, NaNO3,MgSO4 and yeast extract had significant effects on production. The results were confirmed in a batchwise bioreactor, and semi-growth-associated production was detected. Reduction in the surface tension, which indicates the presence of biosurfactant, reached a value of 38 mN/m at the end of 35 hours. Use of the produced biosurfactant for washing crude oil-contaminated soil showed that 2 and 4 times the critical micellar concentration (CMC were able to remove 97 and 99% of the oil, respectively, after 1 month of impregnation.

Yeasts and bacterial biosurfactants as demulsifiers for petroleum derivative in seawater emulsions.

Science.gov (United States)

Rocha E Silva, Fernanda Cristina P; Roque, Bruno Augusto C; Rocha E Silva, Nathalia Maria P; Rufino, Raquel D; Luna, Juliana M; Santos, Valdemir A; Banat, Ibrahim M; Sarubbo, Leonie A

2017-11-15

Oil sludge or waste generated in transport, storage or refining forms highly stable mixtures due to the presence and additives with surfactant properties and water forming complex emulsions. Thus, demulsification is necessary to separate this residual oil from the aqueous phase for oil processing and water treatment/disposal. Most used chemical demulsifiers, although effective, are environmental contaminants and do not meet the desired levels of biodegradation. We investigated the application of microbial biosurfactants as potential natural demulsifiers of petroleum derivatives in water emulsions. Biosurfactants crude extracts, produced by yeasts (Candida guilliermondii, Candida lipolytica and Candida sphaerica) and bacteria (Pseudomonas aeruginosa, Pseudomonas cepacia and Bacillus sp.) grown in industrial residues, were tested for demulsification capacity in their crude and pure forms. The best results obtained were for bacterial biosurfactants, which were able to recover about 65% of the seawater emulsified with motor oil compared to 35-40% only for yeasts products. Biosurfactants were also tested with oil-in-water (O/W) and water-in-oil (W/O) kerosene model emulsions. No relationship between interfacial tension, cell hydrophobicity and demulsification ratios was observed with all the biosurfactants tested. Microscopic illustrations of the emulsions in the presence of the biosurfactants showed the aspects of the emulsion and demulsification process. The results obtained demonstrate the potential of these agents as demulsifiers in marine environments.

Producing Biosurfactants from Purified Microorganisms Obtained from Oil-contaminated Soil

Directory of Open Access Journals (Sweden)

Nader Mokhtarian

2010-09-01

Full Text Available Contamination of soil by crude oil can pose serious problems to ecosystems. Soil washing by solutions containing biosurfactants is one of the most efficient methods for the remediation of contaminated soil by crude oil because it removes not only the crude oil but also heavy metals. In this study, five soil samples were taken from fields exposed to oil compounds over the years in order to produce biosurfactants from microorganisms that were capable of degrading oil compounds. Sixteen such microorganisms were isolated. After cultivation, their emulsification strength was examined using E24 test. From among the experimental microorganisms, a gram-negative and rod-shape microorganism called A-12 showed the greatest value of the E24 test index (36%. For each liter of the culture medium containing 365 mg of microorganisms, 3 gr of the biosurfactant compound was produced and separated as dried powder. The purified biosurfactant was used in the soil washing process. Also, the insulated microorganisms were capable of degrading crude oil floating on wastewaters.

Functional, genetic and chemical characterization of biosurfactants produced by plant growth-promoting Pseudomonas putida 267.

Science.gov (United States)

Kruijt, Marco; Tran, Ha; Raaijmakers, Jos M

2009-08-01

Plant growth-promoting Pseudomonas putida strain 267, originally isolated from the rhizosphere of black pepper, produces biosurfactants that cause lysis of zoospores of the oomycete pathogen Phytophthora capsici. The biosurfactants were characterized, the biosynthesis gene(s) partially identified, and their role in control of Phytophthora damping-off of cucumber evaluated. The biosurfactants were shown to lyse zoospores of Phy. capsici and inhibit growth of the fungal pathogens Botrytis cinerea and Rhizoctonia solani. In vitro assays further showed that the biosurfactants of strain 267 are essential in swarming motility and biofilm formation. In spite of the zoosporicidal activity, the biosurfactants did not play a significant role in control of Phytophthora damping-off of cucumber, since both wild type strain 267 and its biosurfactant-deficient mutant were equally effective, and addition of the biosurfactants did not provide control. Genetic characterization revealed that surfactant biosynthesis in strain 267 is governed by homologues of PsoA and PsoB, two nonribosomal peptide synthetases involved in production of the cyclic lipopeptides (CLPs) putisolvin I and II. The structural relatedness of the biosurfactants of strain 267 to putisolvins I and II was supported by LC-MS and MS-MS analyses. The biosurfactants produced by Ps. putida 267 were identified as putisolvin-like CLPs; they are essential in swarming motility and biofilm formation, and have zoosporicidal and antifungal activities. Strain 267 provides excellent biocontrol activity against Phytophthora damping-off of cucumber, but the lipopeptide surfactants are not involved in disease suppression. Pseudomonas putida 267 suppresses Phy. capsici damping-off of cucumber and provides a potential supplementary strategy to control this economically important oomycete pathogen. The putisolvin-like biosurfactants exhibit zoosporicidal and antifungal activities, yet they do not contribute to biocontrol of Phy

Optimization of cultural conditions for biosurfactant production by Pleurotus djamor in solid state fermentation.

Science.gov (United States)

Velioglu, Zulfiye; Ozturk Urek, Raziye

2015-11-01

Being eco-friendly, less toxic, more biodegradable and biocompatible, biological surfactants have higher activity and stability compared to synthetic ones. In spite of the fact that there are abundant benefits of biosurfactants over the synthetic congeners, the problem related with the economical and large scale production proceeds. The utilization of several industrial wastes in the production media as substrates reduces the production cost. This current study aims optimization of biosurfactant production conditions by Pleurotus djamor, grown on sunflower seed shell, grape wastes or potato peels as renewable cheap substrates in solid state fermentation. After determination of the best substrate for biosurfactant production, we indicate optimum size and amount of solid substrate, volume of medium, temperature, pH and Fe(2+) concentrations on biosurfactant production. In optimum conditions, by reducing water surface tension to 28.82 ± 0.3 mN/m and having oil displacement diameter of 3.9 ± 0.3 cm, 10.205 ± 0.5 g/l biosurfactant was produced. Moreover, chemical composition of biosurfactant produced in optimum condition was determined by FTIR. Lastly, laboratory's large-scale production was carried out in optimum conditions in a tray bioreactor designed by us and 8.9 ± 0.5 g/l biosurfactant was produced with a significant surface activity (37.74 ± 0.3 mN/m). With its economical suggestions and applicability of laboratory's large-scale production, this work indicates the possibility of using low cost agro-industrial wastes as renewable substrates for biosurfactant production. Therefore, using economically produced biosurfactant will reduce cost in several applications such as bioremediation, oil recovery and biodegradation of toxic chemicals. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Development of an In Situ Biosurfactant Production Technology for Enhanced Oil Recovery

Energy Technology Data Exchange (ETDEWEB)

M.J. McInerney; R.M. Knapp; Kathleen Duncan; D.R. Simpson; N. Youssef; N. Ravi; M.J. Folmsbee; T.Fincher; S. Maudgalya; Jim Davis; Sandra Weiland

2007-09-30

The long-term economic potential for enhanced oil recovery (EOR) is large with more than 300 billion barrels of oil remaining in domestic reservoirs after conventional technologies reach their economic limit. Actual EOR production in the United States has never been very large, less than 10% of the total U. S. production even though a number of economic incentives have been used to stimulate the development and application of EOR processes. The U.S. DOE Reservoir Data Base contains more than 600 reservoirs with over 12 billion barrels of unrecoverable oil that are potential targets for microbially enhanced oil recovery (MEOR). If MEOR could be successfully applied to reduce the residual oil saturation by 10% in a quarter of these reservoirs, more than 300 million barrels of oil could be added to the U.S. oil reserve. This would stimulate oil production from domestic reservoirs and reduce our nation's dependence on foreign imports. Laboratory studies have shown that detergent-like molecules called biosurfactants, which are produced by microorganisms, are very effective in mobilizing entrapped oil from model test systems. The biosurfactants are effective at very low concentrations. Given the promising laboratory results, it is important to determine the efficacy of using biosurfactants in actual field applications. The goal of this project is to move biosurfactant-mediated oil recovery from laboratory investigations to actual field applications. In order to meet this goal, several important questions must be answered. First, it is critical to know whether biosurfactant-producing microbes are present in oil formations. If they are present, then it will be important to know whether a nutrient regime can be devised to stimulate their growth and activity in the reservoir. If biosurfactant producers are not present, then a suitable strain must be obtained that can be injected into oil reservoirs. We were successful in answering all three questions. The specific

Isolation of biosurfactant-producing bacteria from the Rancho La Brea Tar Pits.

Science.gov (United States)

Belcher, Richard W; Huynh, Kelvin V; Hoang, Timothy V; Crowley, David E

2012-12-01

This research was conducted to identify culturable surfactant-producing bacterial species that inhabit the 40,000-year-old natural asphalt seep at the Rancho La Brea Tar Pits in Los Angeles, CA. Using phenanthrene, monocyclic aromatic hydrocarbons, and tryptic soy broth as growth substrates, culturable bacteria from the tar pits yielded ten isolates, of which three species of gamma-proteobacteria produced biosurfactants that accumulated in spent culture medium. Partially purified biosurfactants produced by these strains lowered the surface tension of water from 70 to 35-55 mN/m and two of the biosurfactants produced 'dark halos' with the atomized oil assay, a phenomenon previously observed only with synthetic surfactants. Key findings include the isolation of culturable biosurfactant-producing bacteria that comprise a relatively small fraction of the petroleum-degrading community in the asphalt.

Improved Energy Recovery by Anaerobic Grey Water Sludge Treatment with Black Water

NARCIS (Netherlands)

Tervahauta, T.H.; Bryant, I.M.; Hernandez Leal, L.; Buisman, C.J.N.; Zeeman, G.

2014-01-01

This study presents the potential of combining anaerobic grey water sludge treatment with black water in an up-flow anaerobic sludge blanket (UASB) reactor to improve energy recovery within source-separated sanitation concepts. Black water and the mixture of black water and grey water sludge were

Scale up and application of biosurfactant from Bacillus subtilis in Enhanced Oil recovery.

Science.gov (United States)

Amani, Hossein; Mehrnia, Mohammad Reza; Sarrafzadeh, Mohammad Hossein; Haghighi, Manouchehr; Soudi, Mohammad Reza

2010-09-01

There is a lack of fundamental knowledge about the scale up of biosurfactant production. In order to develop suitable technology of commercialization, carrying out tests in shake flasks and bioreactors was essential. A reactor with integrated foam collector was designed for biosurfactant production using Bacillus subtilis isolated from agricultural soil. The yield of biosurfactant on biomass (Y(p/x)), biosurfactant on sucrose (Y(p/s)), and the volumetric production rate (Y) for shake flask were obtained about 0.45 g g(-1), 0.18 g g(-1), and 0.03 g l(-1) h(-1), respectively. The best condition for bioreactor was 300 rpm and 1.5 vvm, giving Y(x/s), Y(p/x), Y(p/s), and Y of 0.42 g g(-1), 0.595 g g(-1), 0.25 g g(-1), and 0.057 g l(-1) h(-1), respectively. The biosurfactant maximum production, 2.5 g l(-1), was reached in 44 h of growth, which was 28% better than the shake flask. The obtained volumetric oxygen transfer coefficient (K(L)a) values at optimum conditions in the shake flask and the bioreactor were found to be around 0.01 and 0.0117 s(-1), respectively. Comparison of K(L)a values at optimum conditions shows that biosurfactant production scaling up from shake flask to bioreactor can be done with K(L) a as scale up criterion very accurately. Nearly 8% of original oil in place was recovered using this biosurfactant after water flooding in the sand pack.

Isolation and partial characterization of a biosurfactant produced by Streptococcus thermophilus A

NARCIS (Netherlands)

Rodrigues, Ligia R.; Teixeira, Jose A.; van der Mei, Henny C.; Oliveira, Rosario

2006-01-01

Isolation and characterization of the surface active components from the crude biosurfactant produced by Streptococcus thermophilus A was studied. A fraction rich in glycolipids was obtained by the fractionation of crude biosurfactant using hydrophobic interaction chromatography. Molecular (by

Utilization of banana peel as a novel substrate for biosurfactant production by Halobacteriaceae archaeon AS65.

Science.gov (United States)

Chooklin, Chanika Saenge; Maneerat, Suppasil; Saimmai, Atipan

2014-05-01

In this study, biosurfactant-producing bacteria was evaluated for biosurfactant production by using banana peel as a sole carbon source. From the 71 strains screened, Halobacteriaceae archaeon AS65 produced the highest biosurfactant activity. The highest biosurfactant production (5.30 g/l) was obtained when the cells were grown on a minimal salt medium containing 35 % (w/v) banana peel and 1 g/l commercial monosodium glutamate at 30 °C and 200 rpm after 54 h of cultivation. The biosurfactant obtained by extraction with ethyl acetate showed high surface tension reduction (25.5 mN/m), a small critical micelle concentration value (10 mg/l), thermal and pH stability with respect to surface tension reduction and emulsification activity, and a high level of salt tolerance. The biosurfactant obtained was confirmed as a lipopeptide by using a biochemical test FT-IR, NMR, and mass spectrometry. The crude biosurfactant showed a broad spectrum of antimicrobial activity and had the ability to emulsify oil, enhance PAHs solubility, and oil bioremediation.

Naphthalene degradation and biosurfactant activity by Bacillus cereus 28BN

Energy Technology Data Exchange (ETDEWEB)

Tuleva, B.; Christova, N. [Inst. of Microbiology, Bulgarian Academy of Sciences, Sofia (Bulgaria); Jordanov, B.; Nikolova-Damyanova, B. [Inst. of Organic Chemistry, Sofia (Bulgaria); Petrov, P. [National Center of Infectious and Parasitic Diseases, Sofia (Bulgaria)

2005-08-01

Biosurfactant activity and naphthalene degradation by a new strain identified as Bacillus cereus 28BN were studied. The strain grew well and produced effective biosurfactants in the presence of n-alkanes, naphthalene, crude oil and vegetable oils. The biosurfactants were detected by the surface tension lowering of the medium, thin layer chromatography and infrared spectra analysis. With (2%) naphthalene as the sole carbon source, high levels of rhamnolipids at a concentration of 2.3 g l{sup -1} were determined in the stationary growth. After 20 d of incubation 72 {+-} 4% of the initial naphthalene was degraded. This is the first report for a Bacillus cereus rhamnolipid producing strain that utilized naphthalene under aerobic conditions. The strain looks promising for application in environmental technologies. (orig.)

Effect of biosurfactant[0] on the sorption of phenanthrene onto original and H2O2-treated soils

Institute of Scientific and Technical Information of China (English)

PEI Xiaohong; ZHAN Xinhua; ZHOU Lixiang

2009-01-01

The objective of this study was to examine the effect of biosurfactant on sorption of phenanthrene (PHE) onto the original or H2O2-treated black loamy soil (typic isohumisols) and red sandy soil (typic ferralisols). The sorption isotherms were performed with the original and "soft" carbon-removed soils in the presence and absence of biosurfactant (200 mg/L). The sorption and degradation of biosurfactant were investigated. The result showed that organic matter played an important role in PHE sorption onto the black loamy and red sandy soils, and the PHE sorption isotherms on the "soft" carbon-removed soils exhibited more nonlinearity than those on the original soils. The values of partition coefficient (Kd) on the original black loamy soil with or without 200 mg/L biosurfactant were 181.6 and 494.5 mL/g, respectively. Correspondingly, in the red sandy soil, Kd was 246.4 and 212.8 mL/g in the presence or absence of biosurfactant, respectively. The changes of Kd suggested that biosurfactant inhibited PHE sorption onto the black loamy soil, but facilitated PHE sorption onto the red sandy soil. The nonlinearity of PHE sorption isotherm was decreased in the presence of biosurfactant. Site specific sorption might occur during PHE sorption onto both the original and the "soft" carbon-removed soils in the presence of biosurfactant. It was noted that biosurfactant could also be sorbed onto soils. The maximal sorption capacity of the red sandy soil for biosurfactant was (76.9 ± 0.007) μg/g, which was 1.31 times that of black loamy soil. Biosurfactant was degraded quickly in the two selected soils, and 92% of biosurfactant were mineralized throughout the incubation experiment for 7 d. It implied that biosurfactant should be added frequently when the remediation of polycyclic aromatic hydrocarbon (PAH)-contaminated soils was conducted through PAH desorption approach facilitated by biosurfactant.

Effective Biosurfactants Production by Pseudomonas aeruginosa and its Efficacy on Different Oils

Directory of Open Access Journals (Sweden)

Sarita Kumari

2010-07-01

Full Text Available A rhamnolipid producing bacterium, Pseudomonas aeruginosa was isolated from contaminated soil with oily wastes. The Pseudomonas aeruginosa grown with glucose and corn oil as a carbon source produced bio-surfactant. This biosurfactant was purified by procedures that included chloroform-ethanol extraction and 0.05M bicarbonate treatments. The active compound was identified as rhamnolipid by using thin layer chromatography. The emulsification activity of bio-surfactant, the coconut oil responded better than the olive oil, groundnut oil and sunflower oil and gave a maximum level of 1 cm.

Coculture induced improved production of biosurfactant by Staphylococcus lentus SZ2: Role in protecting Artemia salina against Vibrio harveyi.

Science.gov (United States)

Hamza, Faseela; Kumar, Ameeta Ravi; Zinjarde, Smita

2018-07-01

Coculturing microorganisms can lead to enhanced production of bioactive compounds as a result of cross-species or cross-genera interactions. In this study, we demonstrate improved production of the biosurfactant (BS-SLSZ2 with antibiofilm properties) by the marine epibiotic bacterium Staphylococcus lentus SZ2 after cross-genera interactions with an aquaculture pathogen Vibrio harveyi. In cocultures, growth of V. harveyi was completely inhibited and resultant biofilms were exclusively composed of S. lentus. The cell free supernatant (CFS) derived from cocultures displayed improved antibiofilm activity with enhanced contents of BS-SLSZ2 compared to monocultured S. lentus. During coculture experiments, after short periods of incubation (6 and 12 h), 2.3 fold increased production of BS-SLSZ2 was observed. Planktonic growth of V. harveyi was also inhibited after coculturing with S. lentus as evidenced from plate culture-based studies and microscopic observations. The CFS derived from monocultures and cocultures did not display bactericidal activity and the observed inhibition of V. harveyi could be of competitive nature. During in vivo challenge experiments, S. lentus protected the model aquaculture system Artemia salina from V. harveyi infections. Seven days post infection, survival of the group of larvae infected with V. harveyi was 5 ± 4.47%. Better survival rates (73.33 ± 5.16%, comparable with the unexposed group) were observed in the group of larvae incubated with S. lentus and V. harveyi. This study highlights increased biosurfactant production by cocultured S. lentus and the application of this bacterium as a protective probiotic strain for inclusion in aquaculture practices. Copyright © 2018 Elsevier Inc. All rights reserved.

Mass spectrometric study of rhamnolipid biosurfactants and their interactions with cell membrane phospholipids

Directory of Open Access Journals (Sweden)

Pashynska V. A.

2009-12-01

Full Text Available Aim. To examine the formation of supramolecular complexes of biogenous rhamnolipids with membrane phospholipids that is considered as a molecular mechanism of the biosurfactants antimicrobial action. Method. In the present work rhamnolipid biosurfactant samples produced by Pseudomonas sp. PS-17 strain have been investigated by electrospray ionization mass spectrometry for the first time. Results. As a result of the study, characteristic mass spectra of the rhamnolipid samples were obtained, that can be used as reference spectra for mass spectrometric identification of the compounds in any biological or industrial samples. At the next stage of the experiments the pair systems, containing the biosurfactants and a membrane phospholipid dipalmitoylphosphatidylcholine, have been tested. The cationized noncovalent complexes of the rhamnolipids with the phospholipid were observed in the spectra. Conclusions. The results obtained testify to the consideration that rhamnolipids (similar to other membranotropic agents can form stable supramolecular complexes with membrane phospholipids that are able to evoke the biosurfactants antimicrobial action. A great potential of electrospray ionization mass spectrometry for the biosurfactants identification and study has been demonstrated in the work.

Biosurfactant Production by Pseudomonas aeruginosa and Burkholderia gladioli Isolated from Mangrove Sediments Using Alternative Substrates

Directory of Open Access Journals (Sweden)

Karla Maria Catter

2016-10-01

Full Text Available Biosurfactants are surface-active agents produced by a variety of microorganisms. To make biosurfactant production economically feasible, several alternative carbon sources have been proposed. This study describes biosurfactant production by strains of Pseudomonas aeruginosa and Burkholderia gladioli isolated from mangrove sediments in Northeastern Brazil and cultured in mineral media enriched with waste cooking oil. The biosurfactants were tested for drop collapse, emulsion formation and stability and surface tension. P. aeruginosa performed better both at lowering the surface tension (from 69 to 28 mN/m and at forming stable emulsions (approximately 80% at 48 hours of culture. The strains tested in this study were found to be efficient biosurfactant producers when cultured on substrates enriched with vegetable oil. DOI: http://dx.doi.org/10.17807/orbital.v8i5.771

Biosurfactant-producing yeasts widely inhabit various vegetables and fruits.

Science.gov (United States)

Konishi, Masaaki; Maruoka, Naruyuki; Furuta, Yoshifumi; Morita, Tomotake; Fukuoka, Tokuma; Imura, Tomohiro; Kitamoto, Dai

2014-01-01

The isolation of biosurfactant-producing yeasts from food materials was accomplished. By a combination of a new drop collapse method and thin-layer chromatography, 48 strains were selected as glycolipid biosurfactant producers from 347 strains, which were randomly isolated from various vegetables and fruits. Of the producers, 69% were obtained from vegetables of the Brassica family. Of the 48 producers, 15 strains gave relatively high yields of mannosylerythritol lipids (MELs), and were identified as Pseudozyma yeasts. These strains produced MELs from olive oil at yields ranging from 8.5 to 24.3 g/L. The best yield coefficient reached 0.49 g/g as to the carbon sources added. Accordingly, MEL producers were isolated at high efficiency from various vegetables and fruits, indicating that biosurfactant producers are widely present in foods. The present results should facilitate their application in the food and related industries.

Comparison of biosurfactant detection methods reveals hydrophobic surfactants and contact-regulated production

Science.gov (United States)

Biosurfactants are diverse molecules with numerous biological functions and industrial applications. A variety of environments were examined for biosurfactant-producing bacteria using a versatile new screening method. The utility of an atomized oil assay was assessed for a large number of bacteria...

Production of Lipopeptide Biosurfactant by a Marine Nesterenkonia sp. and Its Application in Food Industry

Science.gov (United States)

Kiran, George S.; Priyadharsini, Sethu; Sajayan, Arya; Priyadharsini, Gopal B.; Poulose, Navya; Selvin, Joseph

2017-01-01

Biosurfactants are smart biomolecules which have wide spread application in medicines, processed foods, cosmetics as well as in bioremediation. In food industry, biosurfactants are used as emulsion stabilizing agents, antiadhesives, and antimicrobial/antibiofilm agents. Nowadays biosurfactant demands in industries has increased tremendously and therefore new bacterial strains are being explored for large scale production of biosurfactants. In this study, an actinobacterial strain MSA31 was isolated from a marine sponge Fasciospongia cavernosa which showed high activity in biosurfactant screening assays such as drop collapsing, oil displacement, lipase and emulsification. Lipopeptide produced by MSA31 was found to be thermostable which was evident in differential scanning calorimetry analysis. The spectral data obtained in the Fourier transform infrared spectroscopy showed the presence of aliphatic groups combined with peptide moiety which is a characteristic feature of lipopeptides. The stability index of lipopeptide MSA31 revealed “halo-alkali and thermal tolerant biosurfactant” which can be used in the food industry. Microtiter plate assay showed 125 μg/ml of lipopeptide was effective in reducing the biofilm formation activity of pathogenic multidrug resistant Staphylococcus aureus. The confocal laser scanning microscopic images provided further evidences that lipopeptide MSA31 was an effective antibiofilm agent. The antioxidant activity of lipopeptide MSA31 may be due to the presence of unsaturated fatty acid present in the molecule. The brine shrimp cytotoxicity assay showed lipopeptide MSA31 was non-toxic and can be used as food additives. Incorporation of lipopeptide MSA31 in muffin showed improved organoleptic qualities compared to positive and negative control. This study provides a valuable input for this lipopeptide to be used in food industry as an effective emulsifier, with good antioxidant activity and as a protective agent against S. aureus. PMID

Production of Lipopeptide Biosurfactant by a Marine Nesterenkonia sp. and Its Application in Food Industry

Directory of Open Access Journals (Sweden)

George S. Kiran

2017-06-01

Full Text Available Biosurfactants are smart biomolecules which have wide spread application in medicines, processed foods, cosmetics as well as in bioremediation. In food industry, biosurfactants are used as emulsion stabilizing agents, antiadhesives, and antimicrobial/antibiofilm agents. Nowadays biosurfactant demands in industries has increased tremendously and therefore new bacterial strains are being explored for large scale production of biosurfactants. In this study, an actinobacterial strain MSA31 was isolated from a marine sponge Fasciospongia cavernosa which showed high activity in biosurfactant screening assays such as drop collapsing, oil displacement, lipase and emulsification. Lipopeptide produced by MSA31 was found to be thermostable which was evident in differential scanning calorimetry analysis. The spectral data obtained in the Fourier transform infrared spectroscopy showed the presence of aliphatic groups combined with peptide moiety which is a characteristic feature of lipopeptides. The stability index of lipopeptide MSA31 revealed “halo-alkali and thermal tolerant biosurfactant” which can be used in the food industry. Microtiter plate assay showed 125 μg/ml of lipopeptide was effective in reducing the biofilm formation activity of pathogenic multidrug resistant Staphylococcus aureus. The confocal laser scanning microscopic images provided further evidences that lipopeptide MSA31 was an effective antibiofilm agent. The antioxidant activity of lipopeptide MSA31 may be due to the presence of unsaturated fatty acid present in the molecule. The brine shrimp cytotoxicity assay showed lipopeptide MSA31 was non-toxic and can be used as food additives. Incorporation of lipopeptide MSA31 in muffin showed improved organoleptic qualities compared to positive and negative control. This study provides a valuable input for this lipopeptide to be used in food industry as an effective emulsifier, with good antioxidant activity and as a protective agent

Screening of biosurfactant-producing Bacillus strains using glycerol from the biodiesel synthesis as main carbon source.

Science.gov (United States)

Sousa, M; Melo, V M M; Rodrigues, S; Sant'ana, H B; Gonçalves, L R B

2012-08-01

Glycerol, a co-product of biodiesel production, was evaluated as carbon source for biosurfactant production. For this reason, seven non-pathogenic biosurfactant-producing Bacillus strains, isolated from the tank of chlorination at the Wastewater Treatment Plant at Federal University of Ceara, were screened. The production of biosurfactant was verified by determining the surface tension value, as well as the emulsifying capacity of the free-cell broth against soy oil, kerosene and N-hexadecane. Best results were achieved when using LAMI005 and LAMI009 strains, whose biosurfactant reduced the surface tension of the broth to 28.8 ± 0.0 and 27.1 ± 0.1 mN m(-1), respectively. Additionally, at 72 h of cultivation, 441.06 and 267.56 mg L(-1) of surfactin were produced by LAMI005 and LAMI009, respectively. The biosurfactants were capable of forming stable emulsions with various hydrocarbons, such as soy oil and kerosene. Analyses carried out with high performance liquid chromatography (HPLC) showed that the biosurfactant produced by Bacillus subtilis LAMI009 and LAMI005 was compatible with the commercially available surfactin standard. The values of minimum surface tension and the CMC of the produced biosurfactant indicated that it is feasible to produce biosurfactants from a residual and renewable and low-cost carbon source, such as glycerol.

Lipopeptide biosurfactant from Bacillus thuringiensis pak2310: A potential antagonist against Fusarium oxysporum.

Science.gov (United States)

Deepak, R; Jayapradha, R

2015-03-01

The aims of the study were to evaluate the effects of a biosurfactant obtained from a novel Bacillus thuringiensis on Fusarium oxysporum to determine the morphological changes in the structure of the fungi and its biofilm in the presence of the biosurfactant and to evaluate the toxicity of the biosurfactant on HEp-2 human epithelial cell lines. The strain was screened and isolated from petroleum contaminated soil based on the E24 emulsification index. The biosurfactant was produced on glycerol, extracted using chloroform:methanol system and purified using HPLC. The purified fraction showing both surface activity (emulsification and oil-spread activity) and anti-fusarial activity (agar well diffusion method) was studied using FT-IR and MALDI-TOF MS, respectively. The minimum inhibitory concentration (MIC) and the biofilm inhibitory concentration (BIC) were determined using dilution method. The effect of biosurfactant on the morphology of Fusarium oxysporum was monitored using light microscopy and confocal laser scanning microscopy (for biofilm). The purified surfactant showed the presence of functional groups like that of surfactin in the FT-IR spectra and MALDI-TOF MS estimated the molecular weight as 700Da. The MIC and BIC were estimated to be 0.05 and 0.5mg/mL, respectively. The molecule was also non-toxic to HEp-2 cell lines at 10× MIC. A non-toxic and effective anti-Fusarium biosurfactant, that is both safe for human use and to the environment, has been characterized. The growth and metabolite production using glycerol (major byproduct of biodiesel and soap industries) also adds up to the efficiency and ecofriendly nature of this biosurfactant. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Bioactivity of glycolipopeptide cell-bound biosurfactants against skin pathogens.

Science.gov (United States)

Vecino, X; Rodríguez-López, L; Ferreira, D; Cruz, J M; Moldes, A B; Rodrigues, L R

2018-04-01

The antimicrobial and anti-adhesive activities of the cell-bound biosurfactants, produced by Lactobacillus pentosus (PEB), characterized as glycolipopeptide macromolecules, were evaluated against several microorganisms present in the skin microflora, envisaging its potential use as a "natural" ingredient in cosmetic and personal care formulations. Their performance was compared with another cell-bound biosurfactants also characterized as glycolipopeptides produced by Lactobacillus paracasei (PAB). At concentrations of 50mg/mL, the PEB showed an important antimicrobial activity against Pseudomonas aeruginosa (85% when extracted with phosphate buffer (PB) and 100% when extracted with phosphate buffer saline (PBS)), Streptococcus agalactiae (100% for both extracts), Staphylococcus aureus (67% when extracted with PBS and 100% when extracted with PB), Escherichia coli (72% when extracted with PB and 89% when extracted with PBS), Streptococcus pyogenes (about 85% for both extracts) and Candida albicans (around 70% for both extracts), comparable with that obtained for the PAB. However, at lower concentrations the PAB exhibited in general higher antimicrobial activities. Biosurfactants produced by both microorganisms also showed significant anti-adhesive properties against all the microorganisms under study, except for E. coli and C. albicans (less than 30%). Overall, these cell-bound biosurfactants could be used as potential antimicrobial and anti-adhesive agents in cosmetic and pharmaceutical formulations. Copyright © 2017 Elsevier B.V. All rights reserved.

Indigenous production of biosurfactant and degradation of crude oil

Directory of Open Access Journals (Sweden)

Hamid Rashedi

2015-04-01

Full Text Available The present study investigated the isolation and identification of biosurfactant producing bacteria from Iranian oil wells. The biosurfactant production of bacteria isolates was evaluated and confirmed using hemolysis and emulsification tests. The biodegradation of crude oil was studied using GC and HPLC analysis. A total of 45 strains have been isolated. These strains showed less than a 40 mN m-1 reduction in surface tension. The effects of different pH (4.2-9.2, salinity concentrations (1%-15%, and temperatures (25-50 in biosurfactant production of isolated strains were evaluated. One of the strains (Bacillus sp. NO.4 showed a high salt tolerance and a successful production of biosurfactant in a vast pH range. Its maximum biomass production (about 3.1 g L-1 dry weight was achieved after 60 hours of growth. The surface tension of the culture broth dropped rapidly after inoculation and reached its lowest value (36 mN m-1 during the exponential phase after about 36-48 hours of growth. The study of the GC graphs showed that higher aliphatic reduction occurred in fractions with C14 to C24 hydrocarbons. The depicted results of the HPLC graphs indicated a 100% degradation of chrysene and fluorine. In this study, we demonstrated the useful capacities of the isolates in removing oil pollutants and their application in MEOR in vitro.

Isolation, Fermentation Optimization and Performance Studies of a Novel Biosurfactant Producing Strain Bacillus amyloliquefaciens

OpenAIRE

Zhang, W.; Zhang, X.; Cui, H.

2015-01-01

In this research, biosurfactant-producing bacteria were isolated from the outlet sludge of a canteen and one promising strain was identified through 16S rDNA sequence as Bacillus amyloliquefaciens. This strain can utilize water-soluble carbon source and the FT-IR analysis indicated the biosurfactant was probably glycolipids. Further factors (fermentation time, temperature, carbon source, nitrogen source, ion concentration) affecting the biosurfactant production were determined. The optimum fe...

Produção de biossurfactante por levedura Biosurfactants production by yeasts

Directory of Open Access Journals (Sweden)

Gizele Cardoso Fontes

2008-01-01

Full Text Available Biosurfactants are molecules extracellularly produced by bacteria, yeast and fungi that have significant interfacial activity properties. This review focuses on relevant parameters that influence biosurfactant production by yeasts. Many works have investigated the optimization of yeast biosurfactant production, mainly within the last decade, revealing that the potential of such microorganisms is not well explored in the industrial field. The main points to increase the process viability lays on the reduction of the production costs and enhancement of biosynthesis efficiency through optimization the culture conditions (carbon and nitrogen source, pH, aeration, speed agitation and the selection of inexpensive medium components.

Removal of PAH using electrokinetic transport of biosurfactants in clayey soil

Energy Technology Data Exchange (ETDEWEB)

Maria, E.; Lin, J. [Dept. of Building Civil and Environmental Engineering, Concordia Univ., Montreal (Canada)

2001-07-01

The electrokinetic introduction of non-toxic, biodegradable surfactants (produced ex-situ) to remediate PAH-contaminated soil was investigated. The lab tests demonstrated the possibility of removal of organic contaminants from clayey soil without hazardous impact to the environment. The rhamnolipids (biosurfactants), produced by Pseudomonas aeruginosa to increase the solubility of PAHs into the aqueous phase, were used in the enhancement of electrokinetic remediation. This study determined the potential on-site production of biosurfactants that was directly introduced to soil by means of electrokinetics. The average removal of phenanthrene achieved 74% in the presence of biosurfactants above CMC. The remaining compounds are left for biodegradation. These results contribute to the development of a new remediation technology - bioelectrokinetics. (orig.)

Effect of Different Carbon Sources on Biosurfactants' Production by Three Strains of Lactobacillus spp.

Science.gov (United States)

Mouafo, Tene Hippolyte; Mbawala, Augustin; Ndjouenkeu, Robert

2018-01-01

The potential of three indigenous bacterial strains ( Lactobacillus delbrueckii N2, Lactobacillus cellobiosus TM1, and Lactobacillus plantarum G88) for the production of biosurfactants using sugar cane molasses or glycerol as substrates was investigated through emulsifying, surface tension, and antimicrobial activities. The different biosurfactants produced with molasses as substrate exhibited high surface tension reduction from 72 mN/m to values ranged from 47.50 ± 1.78 to 41.90 ± 0.79 mN/m and high emulsification index ranging from 49.89 ± 5.28 to 81.00 ± 1.14%. Whatever the Lactobacillus strain or the substrate used, the biosurfactants produced showed antimicrobial activities against Candida albicans LV1, some pathogenic and/or spoilage Gram-positive and Gram-negative bacteria. The yields of biosurfactants with molasses (2.43 ± 0.09 to 3.03 ± 0.09 g/L) or glycerol (2.32 ± 0.19 to 2.82 ± 0.05 g/L) were significantly ( p biosurfactants reveals that they are mainly glycoproteins and glycolipids with molasses and glycerol as substrate, respectively. Therefore, sugar cane molasses or glycerol can effectively be used by Lactobacillus strains as low-cost substrates to increase their biosurfactants production.

The Adhesive Capability of Two Lactobacillus Strains and Physicochemical Properties of Their Synthesized Biosurfactants

Directory of Open Access Journals (Sweden)

Piotr Gołek

2011-01-01

Full Text Available The aim of this study is to describe the adhesive capability of Lactobacillus fermenti 126 and Lactobacillus rhamnosus CCM 1825 as well as to isolate and evaluate the functional properties of their synthesized biosurfactants. Fourier transform infrared spectroscopy shows that both crude biosurfactants contain three components: protein, polysaccharide and phosphate in different ratio. The crude biosurfactants synthesized by Lactobacillus fermenti 126 and Lactobacillus rhamnosus CCM 1825 contain 8 and 9 fractions analyzed by capillary gel electrophoresis. Lactobacillus fermenti 126 and Lactobacillus rhamnosus CCM 1825 strains used in this study synthesize biosurfactants with low effectiveness, critical micelle concentration of 9.0 and 6.0 g/L, and surface tension of (45.1±0.1 and (43.6±0.6 mN/m, respectively. Biosurfactant synthesized by Lactobacillus rhamnosus CCM 1825 demonstrated higher emulsifying and froth-forming activity than that obtained from Lactobacillus fermenti 126, which resulted in better antiadhesive properties. The advantageous adhesive properties of these Lactobacillus strains were confirmed. A positive effect of the impregnation of polystyrene surface with an aqueous solution of biosurfactants on the inhibition of adhesion of Escherichia coli 22, Klebsiella pneumoniae 2 and Pseudomonas aeruginosa W2 to the impregnated surface was found.

Pseudomonas sp. BUP6, a novel isolate from Malabari goat produces an efficient rhamnolipid type biosurfactant.

Science.gov (United States)

Priji, Prakasan; Sajith, Sreedharan; Unni, Kizhakkepowathial Nair; Anderson, Robin C; Benjamin, Sailas

2017-01-01

This study describes the characteristics of a biosurfactant produced by Pseudomonas sp. BUP6, a rumen bacterium, and optimization of parameters required for its production. Initial screening of five parameters (pH, temperature, agitation, incubation, and substrate concentration) was carried out employing Plackett-Burman design, which reduced the number of parameters to 3 (pH, temperature, and incubation) according to their significance on the yield of biosurfactant. A suitable statistical model for the production of biosurfactant by Pseudomonas sp. BUP6 was established according to Box-Behnken design, which resulted in 11% increase (at pH 7, 35 °C, incubation 75 h) in the yield (2070 mg L -1 ) of biosurfactant. The biosurfactant was found stable at a wide range of pH (3-9) with 48 mg L -1 critical micelle concentration; and maintained over 90% of its emulsification ability even after boiling and in presence of sodium chloride (0.5%). The highest cell hydrophobicity (37%) and emulsification (69%) indices were determined with groundnut oil and kerosene, respectively. The biosurfactant was found to inhibit the growth and adhesion of E. coli and S. aureus significantly. From the phytotoxicity studies, the biosurfactant did not show any adverse effect on the germinating seeds of rice and green gram. The structural characterization of biosurfactant employing orcinol method, thin layer chromatography and FT-IR indicated that it is a rhamnolipid (glycolipid). Thus, Pseudomonas sp. BUP6, a novel isolate from Malabari goat is demonstrated as a producer of an efficient rhamnolipid type biosurfactant suitable for application in various industries. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Characterization and properties of the biosurfactant produced by Candida lipolytica UCP 0988

Directory of Open Access Journals (Sweden)

Raquel Diniz Rufino

2014-01-01

Conclusions: The isolated biosurfactant showed no toxicity against different vegetable seeds: Brassica oleracea, Solanum gilo and Lactuca sativa L. and the micro-crustacean Artemia salina. The properties of the biosurfactant produced suggest its potential application in industries that require the use of effective compounds at low cost.

Optimization of biosurfactant production in soybean oil by rhodococcus rhodochrous and its utilization in remediation of cadmium-contaminated solution

Science.gov (United States)

Suryanti, Venty; Hastuti, Sri; Andriani, Dewi

2016-02-01

Biosurfactant production by Rhodococcus rhodochrous in soybean oil was developed, where the effect of medium composition and fermentation time were evaluated. The optimum condition for biosurfactant production was achieved when a medium containing 30 g/L TSB (tryptic soy broth) and 20% v/v soybean oil was used as media with 7 days of fermentation. Biosurfactant was identified as glycolipids type biosurfactant which had critical micelle concentration (CMC) value of 896 mg/L. The biosurfactant had oil in water emulsion type and was able to reduce the surface tension of palm oil about 52% which could stabilize the emulsion up to 12 days. The batch removal of cadmium metal ion by crude and partially purified biosurfactants have been examined from synthetic aqueous solution at pH 6. The results exhibited that the crude biosurfactant had a much better adsorption ability of Cd(II) than that of partially purified biosurfactant. However, it was found that there was no significant difference in the adsorption of Cd(II) with 5 and 10 minutes of contact time. The results indicated that the biosurfactant could be used in remediation of heavy metals from contaminated aqueous solution.

Inhibition of initial adhesion of uropathogenic Enterococcus faecalis by biosurfactants from Lactobacillus isolates.

Science.gov (United States)

Velraeds, M M; van der Mei, H C; Reid, G; Busscher, H J

1996-06-01

In this study, 15 Lactobacillus isolates were found to produce biosurfactants in the mid-exponential and stationary growth phases. The stationary-phase biosurfactants from lactobacillus casei subsp. rhamnosus 36 and ATCC 7469, Lactobacillus fermentum B54, and Lactobacillus acidophilus RC14 were investigated further to determine their capacity to inhibit the initial adhesion of uropathogenic Enterococcus faecalis 1131 to glass in a parallel-plate flow chamber. The initial deposition rate of E. faecalis to glass with an adsorbed biosurfactant layer from L. acidophilus RC14 or L. fermentum B54 was significantly decreased by approximately 70%, while the number of adhering enterococci after 4 h of adhesion was reduced by an average of 77%. The surface activity of the biosurfactants and their activity inhibiting the initial adhesion of E. faecalis 1131 were retained after dialysis (molecular weight cutoff, 6,000 to 8,000) and freeze-drying. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy revealed that the freeze-dried biosurfactants from L. acidophilus RC14 and L. fermentum B54 were richest in protein, while those from L. casei subsp. rhamnosus 36 and ATCC 7469 had relatively high polysaccharide and phosphate contents.

Evaluation of biosurfactants grown in corn oil by Rhodococcus rhodochrous on removing of heavy metal ion from aqueous solution

International Nuclear Information System (INIS)

Suryanti, Venty; Hastuti, Sri; Pujiastuti, Dwi

2016-01-01

The potential application of biosurfactants to remove heavy metal ion from aqueous solution by batch technique was examined. The glycolipids type biosurfactants were grown in a media containing of 20% v/v corn oil with 7 days of fermentation by Rhodococcus rhodochrous. The biosurfactants reduced the surface tension of water of about 51% from 62 mN/m to 30 mN/m. The biosurfactant increased the E24 of water-palm oil emulsion of about 55% from 43% to 97% and could maintain this E24 value of above 50% for up to 9 days. Heavy metal ion removal, in this case cadmium ion, by crude and patially purified biosurfactants has been investigated from aqueous solution at pH 6. Adsorption capacity of Cd(II) ion by crude biosurfactant with 5 and 10 minutes of contact times were 1.74 and 1.82 mg/g, respectively. Additionally, the adsorption capacity of Cd(II) ion by partially purified biosurfactant with 5 and 10 minutes of contact times were 0.79 and 1.34 mg/g, respectively. The results demonstrated that the adsorption capacity of Cd(II) ion by crude biosurfactant was higher than that of by partially purified biosurfactant. The results suggested that the biosurfactant could be used in the removal of heavy metal ions from aqueous solution

Evaluation of biosurfactants grown in corn oil by Rhodococcus rhodochrous on removing of heavy metal ion from aqueous solution

Science.gov (United States)

Suryanti, Venty; Hastuti, Sri; Pujiastuti, Dwi

2016-02-01

The potential application of biosurfactants to remove heavy metal ion from aqueous solution by batch technique was examined. The glycolipids type biosurfactants were grown in a media containing of 20% v/v corn oil with 7 days of fermentation by Rhodococcus rhodochrous. The biosurfactants reduced the surface tension of water of about 51% from 62 mN/m to 30 mN/m. The biosurfactant increased the E24 of water-palm oil emulsion of about 55% from 43% to 97% and could maintain this E24 value of above 50% for up to 9 days. Heavy metal ion removal, in this case cadmium ion, by crude and patially purified biosurfactants has been investigated from aqueous solution at pH 6. Adsorption capacity of Cd(II) ion by crude biosurfactant with 5 and 10 minutes of contact times were 1.74 and 1.82 mg/g, respectively. Additionally, the adsorption capacity of Cd(II) ion by partially purified biosurfactant with 5 and 10 minutes of contact times were 0.79 and 1.34 mg/g, respectively. The results demonstrated that the adsorption capacity of Cd(II) ion by crude biosurfactant was higher than that of by partially purified biosurfactant. The results suggested that the biosurfactant could be used in the removal of heavy metal ions from aqueous solution.

Evaluation of biosurfactants grown in corn oil by Rhodococcus rhodochrous on removing of heavy metal ion from aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Suryanti, Venty, E-mail: venty@mipa.uns.ac.id; Hastuti, Sri; Pujiastuti, Dwi [Department of Chemistry, Faculty of Mathematics and Natural Sciences, Sebelas Maret University Jl. Ir. Sutami 36A, Surakarta, Central Java 57126 (Indonesia)

2016-02-08

The potential application of biosurfactants to remove heavy metal ion from aqueous solution by batch technique was examined. The glycolipids type biosurfactants were grown in a media containing of 20% v/v corn oil with 7 days of fermentation by Rhodococcus rhodochrous. The biosurfactants reduced the surface tension of water of about 51% from 62 mN/m to 30 mN/m. The biosurfactant increased the E24 of water-palm oil emulsion of about 55% from 43% to 97% and could maintain this E24 value of above 50% for up to 9 days. Heavy metal ion removal, in this case cadmium ion, by crude and patially purified biosurfactants has been investigated from aqueous solution at pH 6. Adsorption capacity of Cd(II) ion by crude biosurfactant with 5 and 10 minutes of contact times were 1.74 and 1.82 mg/g, respectively. Additionally, the adsorption capacity of Cd(II) ion by partially purified biosurfactant with 5 and 10 minutes of contact times were 0.79 and 1.34 mg/g, respectively. The results demonstrated that the adsorption capacity of Cd(II) ion by crude biosurfactant was higher than that of by partially purified biosurfactant. The results suggested that the biosurfactant could be used in the removal of heavy metal ions from aqueous solution.

Characterization of a novel biosurfactant produced by Staphylococcus sp. strain 1E with potential application on hydrocarbon bioremediation.

Science.gov (United States)

Eddouaouda, Kamel; Mnif, Sami; Badis, Abdelmalek; Younes, Sonia Ben; Cherif, Slim; Ferhat, Samira; Mhiri, Najla; Chamkha, Mohamed; Sayadi, Sami

2012-08-01

A biosurfactant-producing bacterium (Staphylococcus sp. strain 1E) was isolated from an Algerian crude oil contaminated soil. Biosurfactant production was tested with different carbon sources using the surface tension measurement and the oil displacement test. Olive oil produced the highest reduction in surface tension (25.9 dynes cm(-1)). Crude oil presented the best substrate for 1E biosurfactant emulsification activity. The biosurfactant produced by strain 1E reduced the growth medium surface tension below 30 dynes cm(-1). This reduction was also obtained in cell-free filtrates. Biosurfactant produced by strain 1E showed stability in a wide range of pH (from 2 to 12), temperature (from 4 to 55 °C) and salinity (from 0 to 300 g l(-1)) variations. The biosurfactant produced by strain 1E belonged to lipopeptide group and also constituted an antibacterial activity againt the pathogenic bacteria such as Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa and Bacillus subtilis. Phenanthrene solubility in water was enhanced by biosurfactant addition. Our results suggest that the 1E biosurfactant has interesting properties for its application in bioremediation of hydrocarbons contaminated sites. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An efficient thermotolerant and halophilic biosurfactant-producing bacterium isolated from Dagang oil field for MEOR application

Science.gov (United States)

Wu, Langping; Richnow, Hans; Yao, Jun; Jain, Anil

2014-05-01

Dagang Oil field (Petro China Company Limited) is one of the most productive oil fields in China. In this study, 34 biosurfactant-producing strains were isolated and cultured from petroleum reservoir of Dagang oil field, using haemolytic assay and the qualitative oil-displacement test. On the basis of 16S rDNA analysis, the isolates were closely related to the species in genus Pseudomonas, Staphylococcus and Bacillus. One of the isolates identified as Bacillus subtilis BS2 were selected for further study. This bacterium was able to produce a type of biosurfactant with excessive foam-forming properties at 37ºC as well as at higher temperature of 55ºC. The biosurfactant produced by the strain BS2 could reduce the surface tension of the culture broth from 70.87 mN/m to 28.97 mN/m after 8 days of incubation at 37ºC and to 36.15 mN/m after 20 days of incubation at 55ºC, respectively. The biosurfactant showed stability at high temperature (up to 120ºC), a wide range of pH (2 to 12) and salt concentrations (up to 12%) offering potential for biotechnology. Fourier transform infrared (FT-IR) spectrum of extracted biosurfactant tentatively characterized the produced biosurfactant as glycolipid derivative. Elemental analysis of the biosurfactant by energy dispersive X-ray spectroscopy (EDS) reveals that the biosurfactant was anionic in nature. 15 days of biodegradation of crude oil suggested a preferential usage of n-alkane upon microbial metabolism of BS2 as a carbon substrate and consequently also for the synthesis of biosurfactants. Core flood studies for oil release indicated 9.6% of additional oil recovery over water flooding at 37ºC and 7.2% of additional oil recovery at 55 ºC. Strain BS2 was characterized as an efficient biosurfactant-producing, thermotolerant and halophillic bacterium and has the potential for application for microbial enhanced oil recovery (MEOR) through water flooding in China's oil fields even in situ as adapted to reservoir chemistry and

Isolation and selection of new biosurfactant producing bacteria from degraded palm kernel cake under liquid state fermentation.

Science.gov (United States)

Jamal, Parveen; Mir, Shajrat; Alam, Md Zahangir; Wan Nawawi, Wan M Fazli

2014-01-01

Biosurfactants are surface-active compounds produced by different microorganisms. The aim of this study was to introduce palm kernel cake (PKC) as a novel substrate for biosurfactant production using a potent bacterial strain under liquid state fermentation. This study was primarily based on the isolation and identification of biosurfactant-producing bacteria that could utilize palm kernel cake as a new major substrate. Potential bacterial strains were isolated from degraded PKC and screened for biosurfactant production with the help of the drop collapse assay and by analyzing the surface tension activity. From the screened isolates, a new strain, SM03, showed the best and most consistent results, and was therefore selected as the most potent biosurfactant-producing bacterial strain. The new strain was identified as Providencia alcalifaciens SM03 using the Gen III MicroPlate Biolog Microbial Identification System. The yield of the produced biosurfactant was 8.3 g/L.

Screening of cloud microorganisms isolated at the Puy de Dôme (France) station for the production of biosurfactants

Science.gov (United States)

Renard, Pascal; Canet, Isabelle; Sancelme, Martine; Wirgot, Nolwenn; Deguillaume, Laurent; Delort, Anne-Marie

2016-09-01

A total of 480 microorganisms collected from 39 clouds sampled at the Puy de Dôme station (alt. 1465 m; 45°46'19'' N, 2°57'52'' E; Massif Central, France) were isolated and identified. This unique collection was screened for biosurfactant (surfactants of microbial origin) production by measuring the surface tension (σ) of the crude extracts, comprising the supernatants of the pure cultures, using the pendant drop technique. The results showed that 41 % of the tested strains were active producers (σ biosurfactant producers (σ biosurfactant production (45biosurfactants. We observed some correlations between the chemical composition of cloud water and the presence of biosurfactant-producing microorganisms, suggesting the "biogeography" of this production. Moreover, the potential impact of the production of biosurfactants by cloud microorganisms on atmospheric processes is discussed.

Use of weathered diesel oil as a low-cost raw material for biosurfactant production

Directory of Open Access Journals (Sweden)

A. P. Mariano

2008-06-01

Full Text Available This work aimed to investigate the capability of biosurfactant production by Staphylococcus hominis, Kocuria palustris and Pseudomonas aeruginosa LBI, using weathered diesel oil from a long-standing spillage as raw material. The effect of the culture media (Robert or Bushnell-Haas and of the carbon source (spilled diesel oil or commercial diesel oil on biosurfactant production was evaluated. Erlenmeyer flasks (250 mL containing the cell broth were agitated (240 rpm for 144 h at 27±2ºC. Biosurfactant production was monitored according to the De Nöuy ring method using a Krüss K6 tensiometer. Considering the possibility of intracellular storage of biosurfactant in the cell wall of the cultures S. hominis and K. palustris, experiments were also done applying ultrasound as a way to rupture the cells. For the conditions studied, the cultures did not indicate production of biosurfactants. Results obtained with a hydrocarbon biodegradability test based on the redox indicator 2,6-dichlorophenol indophenol showed that only the commercial diesel was biodegraded by the cultures.

Candida lipolytica UCP0988 Biosurfactant: Potential as a Bioremediation Agent and in Formulating a Commercial Related Product

Science.gov (United States)

Santos, Danyelle K. F.; Resende, Ana H. M.; de Almeida, Darne G.; Soares da Silva, Rita de Cássia F.; Rufino, Raquel D.; Luna, Juliana M.; Banat, Ibrahim M.; Sarubbo, Leonie A.

2017-01-01

The aim of the present study was to investigate the potential application of the biosurfactant from Candida lipolytica grown in low-cost substrates, which has previously been produced and characterized under optimized conditions as an adjunct material to enhance the remediation processes of hydrophobic pollutants and heavy metals generated by the oil industry and propose the formulation of a safe and stable remediation agent. In tests carried out with seawater, the crude biosurfactant demonstrated 80% oil spreading efficiency. The dispersion rate was 50% for the biosurfactant at a concentration twice that of the CMC. The biosurfactant removed 70% of motor oil from contaminated cotton cloth in detergency tests. The crude biosurfactant also removed 30–40% of Cu and Pb from standard sand, while the isolated biosurfactant removed ~30% of the heavy metals. The conductivity of solutions containing Cd and Pb was sharply reduced after biosurfactants' addition. A product was prepared through adding 0.2% potassium sorbate as preservative and tested over 120 days. The formulated biosurfactant was analyzed for emulsification and surface tension under different pH values, temperatures, and salt concentrations and tested for toxicity against the fish Poecilia vivipara. The results showed that the formulation had no toxicity and did not cause significant changes in the tensoactive capacity of the biomolecule while maintaining activity demonstrating suitability for potential future commercial product formulation. PMID:28507538

Candida lipolytica UCP0988 Biosurfactant: Potential as a Bioremediation Agent and in Formulating a Commercial Related Product

Directory of Open Access Journals (Sweden)

Leonie A. Sarubbo

2017-05-01

Full Text Available The aim of the present study was to investigate the potential application of the biosurfactant from Candida lipolytica grown in low-cost substrates, which has previously been produced and characterized under optimized conditions as an adjunct material to enhance the remediation processes of hydrophobic pollutants and heavy metals generated by the oil industry and propose the formulation of a safe and stable remediation agent. In tests carried out with seawater, the crude biosurfactant demonstrated 80% oil spreading efficiency. The dispersion rate was 50% for the biosurfactant at a concentration twice that of the CMC. The biosurfactant removed 70% of motor oil from contaminated cotton cloth in detergency tests. The crude biosurfactant also removed 30–40% of Cu and Pb from standard sand, while the isolated biosurfactant removed ~30% of the heavy metals. The conductivity of solutions containing Cd and Pb was sharply reduced after biosurfactants' addition. A product was prepared through adding 0.2% potassium sorbate as preservative and tested over 120 days. The formulated biosurfactant was analyzed for emulsification and surface tension under different pH values, temperatures, and salt concentrations and tested for toxicity against the fish Poecilia vivipara. The results showed that the formulation had no toxicity and did not cause significant changes in the tensoactive capacity of the biomolecule while maintaining activity demonstrating suitability for potential future commercial product formulation.

Isolation of biosurfactant-producing marine bacteria and characteristics of selected biosurfactant

Directory of Open Access Journals (Sweden)

Kulnaree Phetrong

2007-05-01

Full Text Available Biosurfactant-producing marine bacteria were isolated from oil-spilled seawater collected from harbors and docks in Songkhla Province, Thailand. Haemolytic activity, emulsification activity toward nhexadecane,emulsion of weathered crude oil, drop collapsing test as well as oil displacement test were used to determine biosurfactant producing activity of marine bacteria. Among two-hundred different strains, 40strains exhibited clear zone on blood agar plates. Only eight strains had haemolytic activity and were able to emulsify weathered crude oil in marine broth during cultivation. Eight strains named SM1-SM8 wereidentified by 16S rRNA as Myroides sp. (SM1; Vibrio paraheamolyticus (SM2; Bacillus subtilis (SM3; Micrococcus luteus (SM4; Acinetobacter anitratus (SM6; Vibrio paraheamolyticus (SM7 and Bacilluspumilus (SM8. However, SM5 could not be identified. Strain SM1 showed the highest emulsification activity against weathered crude oil, by which the oil was emulsified within 24 h of cultivation. In addition, strainSM1 exhibited the highest activity for oil displacement test and emulsification test toward n-hexadecane. The emulsification activity against n-hexadecane of crude extract of strain SM1 was stable over a broadrange of temperature (30-121oC, pH (5-12 and salt concentration (0-9% NaCl, whereas CaCl2 showed an adverse effect on emulsifying activity.

Production of lipopeptide biosurfactants by Bacillus atrophaeus 5-2a and their potential use in microbial enhanced oil recovery.

Science.gov (United States)

Zhang, Junhui; Xue, Quanhong; Gao, Hui; Lai, Hangxian; Wang, Ping

2016-10-03

Lipopeptides are known as promising microbial surfactants and have been successfully used in enhancing oil recovery in extreme environmental conditions. A biosurfactant-producing strain, Bacillus atrophaeus 5-2a, was recently isolated from an oil-contaminated soil in the Ansai oilfield, Northwest China. In this study, we evaluated the crude oil removal efficiency of lipopeptide biosurfactants produced by B. atrophaeus 5-2a and their feasibility for use in microbial enhanced oil recovery. The production of biosurfactants by B. atrophaeus 5-2a was tested in culture media containing eight carbon sources and nitrogen sources. The production of a crude biosurfactant was 0.77 g L -1 and its surface tension was 26.52 ± 0.057 mN m -1 in a basal medium containing brown sugar (carbon source) and urea (nitrogen source). The biosurfactants produced by the strain 5-2a demonstrated excellent oil spreading activity and created a stable emulsion with paraffin oil. The stability of the biosurfactants was assessed under a wide range of environmental conditions, including temperature (up to 120 °C), pH (2-13), and salinity (0-50 %, w/v). The biosurfactants were found to retain surface-active properties under the extreme conditions. Additionally, the biosurfactants were successful in a test to simulate microbial enhanced oil recovery, removing 90.0 and 93.9 % of crude oil adsorbed on sand and filter paper, respectively. Fourier transform infrared spectroscopy showed that the biosurfactants were a mixture of lipopeptides, which are powerful biosurfactants commonly produced by Bacillus species. The study highlights the usefulness of optimization of carbon and nitrogen sources and their effects on the biosurfactants production and further emphasizes on the potential of lipopeptide biosurfactants produced by B. atrophaeus 5-2a for crude oil removal. The favorable properties of the lipopeptide biosurfactants make them good candidates for application in the bioremediation of oil

Characterization of sophorolipid biosurfactant produced by Cryptococcus sp. VITGBN2 and its application on Zn(II) removal from electroplating wastewater.

Science.gov (United States)

Basak, Geetanjali; Das, Nilanjana

2014-11-01

The present study aimed at elucidating the role of biosurfactant produced by yeast for the removal of Zn(II) ions from electroplating wastewater. The yeast species isolated from CETP, Vellore, Tamilnadu was identified as Cryptococcus sp.VITGBN2, based on molecular techniques, and was found to be potent producer of biosurfactant in mineral salt media containing vegetable oil as additional carbon source. Chemical structure of the purified biosurfactant was identified as acidic diacetate sophorolipid through GC-MS analysis. Interaction of Zn(II) ions with biosurfactant was monitored using FT-IR, SEM and EDS analysis. Zn (II) removal at 100 mg l(-1) concentration was 84.8% compared were other synthetic surfactants (Tween 80 and sodium dodecyl sulphate), yeast mediated biosurfactant showed enhanced Zn (II) removal in batch mode. The role of biosurfactant on Zn(II) removal was evaluated in column mode packed with biosurfactant entrapped in sodium alginate beads. At a flow rate of 1 ml min(-1) and bed height of 12 cm, immobilized biosurfactant showed 94.34% Zn(II) removal from electroplating wastewater. The present study confirmed that Zn(II) removal was biosurfactant mediated. This is the first report establishing the involvement of yeast mediated biosurfactant in Zn(II) removal from wastewater.

Isolation and characterization of a biosurfactant producing strain, Brevibacilis brevis HOB1.

Science.gov (United States)

Haddad, Namir I A; Wang, Ji; Mu, Bozhong

2008-12-01

Biosurfactant-producing bacteria were isolated from the production water of an oil field. Isolates were screened for biosurfactant production using surface tension test. The highest reduction of surface tension was achieved with a bacterial strain which was identified by 16S rRNA gene sequencing as Brevibacilis brevis HOB1. It has been investigated using different carbon and nitrogen sources. It showed that the strain was able to grow and reduce the surface tension of the broth to 29 mN/m on commercial sugar and maltose, and to 32 mN/m on glucose after 72 h of growth. The maximum amount of biosurfactant was obtained when nitrate ions were supplied as nitrogen source. Biosurfactant produced by Brevibacilis brevis HOB1 was confirmed as a lipopeptide class of biosurfactant using TLC test and mass spectra. Lipopeptide isoforms were isolated from cell-free supernatants by acid-precipitation followed by one step of chromatographic separation on solid-phase ODS C18 column. The separation was confirmed by HPLC and ESI Q-TOF MS spectroscopy. Comparing the mass data obtained and the mass numbers reported for the lipopeptide complexes from other strains, it can be concluded that the major lipopeptide product of Brevibacilis brevis HOB1 is the surfactin isoform. This lipopeptide showed strong antibacterial and antifungal activity. It is a candidate for the biocontrol of pathogens in agriculture and other industries.

Biosurfactant produced from Actinomycetes nocardiopsis A17: Characterization and its biological evaluation.

Science.gov (United States)

Chakraborty, Samrat; Ghosh, Mandakini; Chakraborti, Srijita; Jana, Sougata; Sen, Kalyan Kumar; Kokare, Chandrakant; Zhang, Lixin

2015-08-01

This investigation aims to isolate an Actinomycetes strain producing a biosurfactant from the unexplored region of industrial and coal mine areas. Actinomycetes are selected for this study as their novel chemistry was not exhausted and they have tremendous potential to produce bioactive secondary metabolites. The biosurfactant was characterized and further needed to be utilized for pharmaceutical dosage form. Isolation, purification, screening, and characterization of the Actinomycetes A17 were done followed by its fermentation in optimized conditions. The cell-free supernatant was used for the extraction of the biosurfactant and precipitated by cold acetone. The dried precipitate was purified by TLC and the emulsification index, surface tension and CMC were determined. The isolated strain with preferred results was identified as Actinomycetes nocardiopsis A17 with high foam-forming properties. It gives lipase, amylase, gelatinase, and protease activity. The emulsification index was found to be 93±0.8 with surface tension 66.67 dyne/cm at the lowest concentration and cmc 0.6 μg/ml. These biosurfactants were characterized by Fourier transform infra red (FT-IR) spectroscopy and liquid chromatography-mass spectrometry (LC-MS). Therefore, it can be concluded that the biosurfactant produced by Actinomycetes nocardiopsis sp. strain A17 was found to have satisfactory results with high surface activity and emulsion-forming ability. Copyright © 2015 Elsevier B.V. All rights reserved.

Isolation of thermotolerant, halotolerant, facultative biosurfactant-producing bacteria.

Science.gov (United States)

Ghojavand, H; Vahabzadeh, F; Mehranian, M; Radmehr, M; Shahraki, Kh A; Zolfagharian, F; Emadi, M A; Roayaei, E

2008-10-01

Several facultative bacterial strains tolerant to high temperature and salinity were isolated from the oil reservoir brines of an Iranian oil field (Masjed-I Soleyman). Some of these isolates were able to grow up to 60 degrees C and at high concentration of NaCl (15% w/v). One of the isolates grew at 40 degrees C, while it was able to grow at 15% w/v NaCl. Tolerances to NaCl levels decreased as the growth temperatures were increased. Surfactant production ability was detected in some of these isolates. The use of biosurfactant is considered as an effective mechanism in microbial-enhanced oil recovery processes detected in some of these isolates. The surfactant producers were able to grow at high temperatures and salinities to about 55 degrees C and 10% w/v, respectively. These isolates exhibited morphological and physiological characteristics of the Bacillus genus. The partial sequencing of the 16S ribosomal deoxyribonucleic acid gene of the selected isolates was assigned them to Bacillus subtilis group. The biosurfactant produced by these isolates caused a substantial decrease in the surface tension of the culture media to 26.7 mN/m. By the use of thin-layer chromatography technique, the presence of the three compounds was detected in the tested biosurfactant. Infrared spectroscopy and (1)H nuclear magnetic resonance analysis were used, and the partial structural characterization of the biosurfactant mixture of the three compounds was found to be lipopeptidic in nature. The possibility of use of the selected bacterial strains reported, in the present study, in different sectors of the petroleum industry has been addressed.

Inhibition of initial adhesion of uropathogenic Enterococcus faecalis by biosurfactants from Lactobacillus isolates

NARCIS (Netherlands)

Velraeds, MMC; vanderMei, HC; Reid, G; Busscher, HJ

In this study, 15 Lactobacillus isolates were found to produce biosurfactants in the mid-exponential and stationary growth phases. The stationary-phase biosurfactants from Lactobacillus casei subsp. rhamnosus 36 and ATCC 7469, Lactobacillus fermentum B54, and Lactobacillus acidophilus RC14 were

Production and characterization of a biosurfactant produced by Streptomyces sp. DPUA 1559 isolated from lichens of the Amazon region.

Science.gov (United States)

Santos, A P P; Silva, M D S; Costa, E V L; Rufino, R D; Santos, V A; Ramos, C S; Sarubbo, L A; Porto, A L F

2017-12-11

Surfactants are amphipathic compounds containing both hydrophilic and hydrophobic groups, capable to lower the surface or interfacial tension. Considering the advantages of the use of biosurfactants produced by microorganisms, the aim of this paper was to develop and characterize a biosurfactant produced by Streptomyces sp. DPUA1559 isolated from lichens of the Amazon region. The microorganism was cultured in a mineral medium containing 1% residual frying soybean oil as the carbon source. The kinetics of biosurfactant production was accompanied by reducing the surface tension of the culture medium from 60 to values around 27.14 mN/m, and by the emulsification index, which showed the efficiency of the biosurfactant as an emulsifier of hydrophobic compounds. The yield of the isolated biosurfactant was 1.74 g/L, in addition to the excellent capability of reducing the surface tension (25.34 mN/m), as observed from the central composite rotational design when the biosurfactant was produced at pH 8.5 at 28°C. The critical micelle concentration of the biosurfactant was determined as 0.01 g/mL. The biosurfactant showed thermal and pH stability regarding the surface tension reduction, and tolerance under high salt concentrations. The isolated biosurfactant showed no toxicity to the micro-crustacean Artemia salina, and to the seeds of lettuce (Lactuca sativa L.) and cabbage (Brassica oleracea L.). The biochemistry characterization of the biosurfactant showed a single protein band, an acid character and a molecular weight around 14.3 kDa, suggesting its glycoproteic nature. The results are promising for the industrial application of this new biosurfactant.

Production and characterisation of glycolipid biosurfactant by Halomonas sp. MB-30 for potential application in enhanced oil recovery.

Science.gov (United States)

Dhasayan, Asha; Kiran, G Seghal; Selvin, Joseph

2014-12-01

Biosurfactant-producing Halomonas sp. MB-30 was isolated from a marine sponge Callyspongia diffusa, and its potency in crude oil recovery from sand pack column was investigated. The biosurfactant produced by the strain MB-30 reduced the surface tension to 30 mN m(-1) in both glucose and hydrocarbon-supplemented minimal media. The critical micelle concentration of biosurfactant obtained from glucose-based medium was at 0.25 mg ml(-1) at critical micelle dilution 1:10. The chemical structure of glycolipid biosurfactant was characterised by infrared spectroscopy and proton magnetic resonance spectroscopy. The emulsification activity of MB-30 biosurfactant was tested with different hydrocarbons, and 93.1 % emulsification activity was exhibited with crude oil followed by kerosene (86.6 %). The formed emulsion was stable for up to 1 month. To identify the effectiveness of biosurfactant for enhanced oil recovery in extreme environments, the interactive effect of pH, temperature and salinity on emulsion stability with crude oil and kerosene was evaluated. The stable emulsion was formed at and above pH 7, temperature >80 °C and NaCl concentration up to 10 % in response surface central composite orthogonal design model. The partially purified biosurfactant recovered 62 % of residual crude oil from sand pack column. Thus, the stable emulsifying biosurfactant produced by Halomonas sp. MB-30 could be used for in situ biosurfactant-mediated enhanced oil recovery process and hydrocarbon bioremediation in extreme environments.

Isolation of Crude Oil from Polluted Waters Using Biosurfactants Pseudomonas Bacteria: Assessment of Bacteria Concentration Effects

Directory of Open Access Journals (Sweden)

A. Khalifeh

2013-04-01

Full Text Available Biological decomposition techniques and isolation of environmental pollutions using biosurfactants bacteria are effective methods of environmental protection. Surfactants are amphiphilic compounds that are produced by local microorganisms and are able to reduce the surface and the stresses between surfaces. As a result, they will increase solubility, biological activity, and environmental decomposition of organic compounds. This study analyzes the effects of biosurfactants on crude oil recovery and its isolation using pseudomonas sea bacteria species. Preparation of biosurfactants was done in glass flasks and laboratory conditions. Experiments were carried out to obtain the best concentration of biosurfactants for isolating oil from water and destroying oil-in-water or water-in-oil emulsions in two pH ranges and four saline solutions of different concentrations. The most effective results were gained when a concentration of 0.1% biosurfactants was applied.

Biosurfactants production potential of native strains of Bacillus cereus and their antimicrobial, cytotoxic and antioxidant activities.

Science.gov (United States)

Basit, Madiha; Rasool, Muhammad Hidayat; Naqvi, Syed Ali Raza; Waseem, Muhammad; Aslam, Bilal

2018-01-01

Present study was designed to evaluate the biosurfactant production potential by native strains of Bacillus cereus as well as determine their antimicrobial and antioxidant activities. The strains isolated from garden soil were characterized as B. cereus MMIC 1, MMIC 2 and MMIC 3. Biosurfactants were extracted as grey white precipitates. Optimum conditions for biosurfactant production were 37°C, the 7th day of incubation, 0.5% NaCl, pH 7.0. Moreover, corn steep liquor was the best carbon source. Biuret test, Thin Layer Chromatography (TLC), agar double diffusion and Fourier Transform Infrared Spectroscopy (FTIR) characterized the biosurfactants as cationic lipopeptides. Biosurfactants exhibited significant antibacterial and antifungal activity against S. aureus, E. coli, P. aeruginosa, K. pneumoniae, A. niger and C. albicans at 30 mg/ml. Moreover, they also possessed antiviral activity against NDV at 10 mg/ml. Cytotoxicity assay in BHK-21 cell lines revealed 63% cell survival at 10 mg/ml of biosurfactants and thus considered as safe. They also showed very good antioxidant activity by ferric-reducing activity and DPPH scavenging activity at 2 mg/ml. Consequently, the study offers an insight for the exploration of new bioactive molecules from the soil. It was concluded that lipopeptide biosurfactants produced from native strains of B. cereus may be recommended as safe antimicrobial, emulsifier and antioxidant agent.

Improved anaerobic biodegradation of biosolids by the addition of food waste as a co-substrate

Energy Technology Data Exchange (ETDEWEB)

Kim, H.-W.; Han, S.-K.; Song, Y.-C.; Baek, B.-C.; Yoo, K.-S.; Lee, J.-J.; Shin, H.-S.

2003-07-01

The temperature phased anaerobic digestion (TPAD) process was applied to increase the performance of anaerobic treatment of biosolids. Previously obtained results indicate that this system showed the advantages of thermophilic and mesophilic anaerobic digestion process. By comparing the performance of each reactor of the system, it was illustrated that the main stage of methane production was the thermophilic reactor which has faster microbial metabolism. However, the result revealed that substrate characteristics of low VS/TS limited the system performance. Therefore, to evaluate the effect of food waste as a co-substrate for improving anaerobic biodegradability, biochemical methane potential (BMP) tests were conducted in thermophilic conditions with biomass of thermophilic reactor. It was confirmed that the co-digestion of sewage sludge mixed with food waste had a distinct improvement on biodegradability. The most significant advantages were the preferable environment provided by food waste for the growth and activity of anaerobes and the mutual assistance between biosolids and food waste. (author)

Development of More Effective Biosurfactants for Enhanced Oil Recovery/Advanced Recovery Concepts Awards

Energy Technology Data Exchange (ETDEWEB)

McInerney, M.J.; Marsh, T.L.; Zhang, X.; Knapp, R.M.; Nagle, Jr., D.P.; Sharma, P.K.; Jackson, B.E.

2002-05-28

The objectives of this were two fold. First, core displacement studies were done to determine whether microbial processes could recover residual oil at elevated pressures. Second, the importance of biosurfactant production for the recovery of residual oil was studies. In these studies, a biosurfactant-producing, microorganisms called Bacillus licheniformis strain JF-2 was used. This bacterium produces a cyclic peptide biosurfactant that significantly reduces the interfacial tension between oil and brine (7). The use of a mutant deficient in surfactant production and a mathematical MEOR simulator were used to determine the major mechanisms of oil recovery by these two strains.

Isolation and characterization of halophilic Bacillus sp. BS3 able to produce pharmacologically important biosurfactants.

Science.gov (United States)

Donio, M B S; Ronica, S F A; Viji, V Thanga; Velmurugan, S; Jenifer, J Adlin; Michaelbabu, M; Citarasu, T

2013-11-01

To characterize the pharmacological importance of biosurfactants isolated from halophilic Bacillus sp BS3. Halophilic Bacillus sp. BS3 was isolated from solar salt works, identified by 16S rRNA sequencing and was used for screening their biosurfactant production. Characters of the biosurfactant and their anticancer activity were analyzed and performed in mammary epithelial carcinoma cell at different concentrations. The biosurfactant were characterized by TLC, FTIR and GC-MS analysis and identified as lipopeptide type. GC-MS analysis revealed that, the biosurfactant had various compounds including 13-Docosenamide, (Z); Mannosamine, 9- and N,N,N',N'-tetramethyl. Surprisingly the antiviral activity was found against shrimp white spot syndrome virus (WSSV) by suppressing the viral replication and significantly raised shrimp survival (Pbiosurfactants, among the various concentrations of biosurfactants such as 0.000 25, 0.002 5, 0.025, 0.25 and 2.5 μg, the 0.25 μg concentration suppressed the cells significantly (P<0.05) to 24.8%. Based on the findings, the present study concluded that, there is a possibility to develop eco-friendly antimicrobial and anticancer drugs from the extremophilic origin. Copyright © 2013 Hainan Medical College. Published by Elsevier B.V. All rights reserved.

Microorganism selection and biosurfactant production in a continuously and periodically operated bioslurry reactor.

Science.gov (United States)

Cassidy, D P; Hudak, A J

2001-06-29

A continuous-flow reactor (CSTR) and a soil slurry-sequencing batch reactor (SS-SBR) were maintained in 8l vessels for 180 days to treat a soil contaminated with diesel fuel (DF). Concentrations of Candida tropicalis, Brevibacterium casei, Flavobacterium aquatile, Pseudomonas aeruginosa, and Pseudomonas fluorescens were determined using fatty acid methyl ester (FAME) analysis. DF removal (biological and volatile) and biosurfactant concentrations were measured. The SS-SBR encouraged the growth of biosurfactant-producing species relative to the CSTR. Counts of biosurfactant-producing species (C. tropicalis, P. aeruginosa, P. fluorescens) relative to total microbial counts were 88% in the SS-SBR and 23% in the CSTR. Biosurfactants were produced in the SS-SBR to levels of nearly 70 times the critical micelle concentration (CMC) early in the cycle, but were completely degraded by the end of each cycle. No biosurfactant production was observed in the CSTR. DF biodegradation rates were over 40% greater and DF stripping was over five times lower in the SS-SBR than the CSTR. However, considerable foaming occurred in the SS-SBR. Reversing the mode of operation in the reactors on day 80 caused a complete reversal in microbial consortia and reactor performance by day 120. These results show that bioslurry reactor operation can be manipulated to control overall reactor performance.

Utilization of Paneer Whey Waste for Cost-Effective Production of Rhamnolipid Biosurfactant.

Science.gov (United States)

Patowary, Rupshikha; Patowary, Kaustuvmani; Kalita, Mohan Chandra; Deka, Suresh

2016-10-01

The present study aimed at isolating rhamnolipid biosurfactant-producing bacteria that could utilize paneer whey, an abundant waste source as sole medium for the production purpose. Pseudomonas aeruginosa strain, SR17, was isolated from hydrocarbon-contaminated soil that could efficiently utilize paneer whey for rhamnolipid production and reduce surface tension of the medium from 52 to 26.5 mN/m. The yield of biosurfactant obtained was 2.7 g/l, upgraded to 4.8 g/l when supplemented with 2 % glucose and mineral salts. Biochemical, FTIR, and LC-MS analysis revealed that extracted biosurfactant is a combination of both mono and di-rhamnolipid congeners. The critical micelle concentration (CMC) was measured to be 110 mg/l. Emulsification activity of the biosurfactant against n-hexadecane, olive oil, kerosene, diesel oil, engine oil, and crude oil were found to be 83, 88, 81, 92, 86, and 100 %, respectively. The rhamnolipid was detected to be non-toxic against mouse fibroblastic cell line L292.

Screening of novel microorganisms for biosurfactant and biocontrol activity against Phytophthora infestans.

Science.gov (United States)

Tomar, Sonica; Singh, B P; Lal, Mehi; Ma, Khan; Hussain, Touseef; Sharma, Sanjeev; Kaushik, S K; Kumar, Satish

2014-09-01

In the present study, 95 isolates of bacteria were tested for their biosurfactant as well as biocontrol activity against Phytophthora infestans. The results revealed that only 15.8% isolates showed biosurfactant activity. The emulsification index ranged from 0-68% and 24.2% isolates showed positive reaction for biosurfactant properties. In emulsification assay and oil spreading test, 18.95% and 5.26% isolates, respectively scored positive for biosurfactant production. Among all, only five isolates were found effective against P. infestans, for biocontrol properties. Pseudomonas aeruginosa-1 showed 62.22% inhibition zone after 72 hrs while P. aeruginosa-3 showed 46.42%. Forty-eight hrs old culture supernatants were highly effective in food-poisoning test, tuber slice test and detached leaf method against P. infestans. In whole potato plant test, bacterial cell based formulation, culture supernatant and bacterial cell suspension of P. aeruginosa-1 showed 10.42%, 9.94% and 17.96% diseases severity respectively, as against 53.96% in control. This isolate holds promise as biological control agent against P. infestans in field.

Improved Procedure for Transport of Dental Plaque Samples and Other Clinical Specimens Containing Anaerobic Bacteria

Science.gov (United States)

Spiegel, Carol A.; Minah, Glenn E.; Krywolap, George N.

1979-01-01

An improved transport system for samples containing anaerobic bacteria was developed. This system increased the recovery rate of anaerobic bacteria up to 28.8% as compared to a commonly used method. PMID:39087

Bacillus amyloliquefaciens TSBSO 3.8, a biosurfactant-producing strain with biotechnological potential for microbial enhanced oil recovery.

Science.gov (United States)

Alvarez, Vanessa Marques; Jurelevicius, Diogo; Marques, Joana Montezano; de Souza, Pamella Macedo; de Araújo, Livia Vieira; Barros, Thalita Gonçalves; de Souza, Rodrigo Octavio Mendonça Alves; Freire, Denise Maria Guimarães; Seldin, Lucy

2015-12-01

A screening for biosurfactant-producing bacteria was conducted with 217 strains that were isolated from environmental samples contaminated with crude oil and/or petroleum derivatives. Although 19 promising biosurfactant producers were detected, strain TSBSO 3.8, which was identified by molecular methods as Bacillus amyloliquefaciens, drew attention for its production of a high-activity compound that presented an emulsification activity of 63% and considerably decreased surface (28.5 mN/m) and interfacial (11.4 mN/m) tensions in Trypticase Soy Broth culture medium. TSBSO 3.8 growth and biosurfactant production were tested under different physical and chemical conditions to evaluate its biotechnological potential. Biosurfactant production occurred between 0.5% and 7% NaCl, at pH values varying from 6 to 9 and temperatures ranging from 28 to 50 °C. Moreover, biosurfactant properties remained the same after autoclaving at 121 °C for 15 min. The biosurfactant was also successful in a test to simulate microbial enhanced oil recovery (MEOR). Mass spectrometry analysis showed that the surface active compound was a surfactin, known as a powerful biosurfactant that is commonly produced by Bacillus species. The production of a high-efficiency biosurfactant, under some physical and chemical conditions that resemble those experienced in an oil production reservoir, such as high salinities and temperatures, makes TSBSO 3.8 an excellent candidate and creates good expectations for its application in MEOR. Copyright © 2015 Elsevier B.V. All rights reserved.

Screening of biosurfactants from cloud microorganisms

Science.gov (United States)

Sancelme, Martine; Canet, Isabelle; Traikia, Mounir; Uhliarikova, Yveta; Capek, Peter; Matulova, Maria; Delort, Anne-Marie; Amato, Pierre

2015-04-01

The formation of cloud droplets from aerosol particles in the atmosphere is still not well understood and a main source of uncertainties in the climate budget today. One of the principal parameters in these processes is the surface tension of atmospheric particles, which can be strongly affected by trace compounds called surfactants. Within a project devoted to bring information on atmospheric surfactants and their effects on cloud droplet formation, we focused on surfactants produced by microorganisms present in atmospheric waters. From our unique collection of microorganisms, isolated from cloud water collected at the Puy-de-Dôme (France),1 we undertook a screening of this bank for biosurfactant producers. After extraction of the supernatants of the pure cultures, surface tension of crude extracts was determined by the hanging drop technique. Results showed that a wide variety of microorganisms are able to produce biosurfactants, some of them exhibiting strong surfactant properties as the resulting tension surface decreases to values less then 35 mN.m-1. Preliminary analytical characterization of biosurfactants, obtained after isolation from overproducing cultures of Rhodococcus sp. and Pseudomonas sp., allowed us to identify them as belonging to two main classes, namely glycolipids and glycopeptides. 1. Vaïtilingom, M.; Attard, E.; Gaiani, N.; Sancelme, M.; Deguillaume, L.; Flossmann, A. I.; Amato, P.; Delort, A. M. Long-term features of cloud microbiology at the puy de Dôme (France). Atmos. Environ. 2012, 56, 88-100. Acknowledgements: This work is supported by the French-USA ANR SONATA program and the French-Slovakia programs Stefanik and CNRS exchange.

Effects of Au/Fe and Fe nanoparticles on Serratia bacterial growth and production of biosurfactant

International Nuclear Information System (INIS)

Liu, Jia; Vipulanandan, Cumaraswamy

2013-01-01

The overall objective of this study was to compare the effects of Au/Fe and Fe nanoparticles on the growth and performance of Serratia Jl0300. The nanoparticle effect was quantified not only by the bacterial growth on agar plate after 1 hour interaction with the nanoparticles, but also by its production of a biosurfactant from used vegetable oil. The nanoparticles were prepared using the foam method. The concentrations of the nanoparticles used for the bacterial interaction study were varied from 1 mg/L to 1 g/L. The test results showed that the effect of nanoparticles on the bacterial growth and biosurfactant production varied with nanoparticle type, concentrations, and interaction time with the bacteria. Au/Fe nanoparticles didn't show toxicity to Serratia after short time (1 h) exposure, while during 8 days fermentation Au/Fe nanoparticles inhibited the growth of Serratia as well as the biosurfactant production when the concentration of the nanoparticles was higher than 10 mg/L. Fe nanoparticles showed inhibition effects to bacterial growth both after short time and long time interaction with Serratia, as well as to biosurfactant production when its concentration was higher than 100 mg/L. Based on the trends observed in this study, analytical models have been developed to predict the bacterial growth and biosurfactant production with varying concentrations of nanoparticles. - Highlights: • Modeled the effect of nanoparticles on the bacterial growth and biosurfactant production. • Effects of Au/Fe nonoparticles on Serratia Bacterial Growth and Production of Biosurfactant. • Scanning Electron Micrograph of bacteria-nanoparticles interaction

Characterization of Biosurfactant Produced by Bacillus licheniformis TT42 Having Potential for Enhanced Oil Recovery.

Science.gov (United States)

Suthar, Harish; Nerurkar, Anuradha

2016-09-01

Bacillus licheniformis TT42 produced a low-molecular weight anionic biosurfactant that reduced the surface tension of water from 72 to 27 mN/m and the interfacial tension from 12 to 0.05 mN/m against crude oil. We have earlier reported significant enhancement in oil recovery in laboratory sand pack columns and core flood studies, by biosurfactant-TT42 compared to standard strain, Bacillus mojavensis JF2. In the context of this application of the biosurfactant-TT42, its characterization was deemed important. In the preliminary studies, the biosurfactant-TT42 was found to be functionally stable at under conditions of temperature, pH, and salinity generally prevalent in oil reservoirs. Furthermore, the purified biosurfactant-TT42 was found to have a CMC of 22 mg/l. A newly developed activity staining TLC method was used for the purification of biosurfactant-TT42. Structural characterization of biosurfactant-TT42 using TLC, Fourier transform infrared spectroscopy (FTIR), GC-MS, and matrix-assisted laser desorption ionization time of flight (MALDI-TOF)/TOF suggested that it was a mixture of lipopeptide species, all having a common hydrophilic cyclic heptapeptide head with the sequence, Gln-Leu/Ileu-Leu/Ileu-Val-Asp-Leu/Ileu-Leu/Ileu linked to hydrophobic tails of different lengths of 3β-OH-fatty acids bearing 1043, 1057 and 1071 Da molecular weight, where 3β-OH-C19 fatty acid was predominant. This is the longest chain length of fatty acids reported in a lipopeptide.

Effects of Au/Fe and Fe nanoparticles on Serratia bacterial growth and production of biosurfactant

Energy Technology Data Exchange (ETDEWEB)

Liu, Jia; Vipulanandan, Cumaraswamy, E-mail: cvipulanandan@uh.edu

2013-10-15

The overall objective of this study was to compare the effects of Au/Fe and Fe nanoparticles on the growth and performance of Serratia Jl0300. The nanoparticle effect was quantified not only by the bacterial growth on agar plate after 1 hour interaction with the nanoparticles, but also by its production of a biosurfactant from used vegetable oil. The nanoparticles were prepared using the foam method. The concentrations of the nanoparticles used for the bacterial interaction study were varied from 1 mg/L to 1 g/L. The test results showed that the effect of nanoparticles on the bacterial growth and biosurfactant production varied with nanoparticle type, concentrations, and interaction time with the bacteria. Au/Fe nanoparticles didn't show toxicity to Serratia after short time (1 h) exposure, while during 8 days fermentation Au/Fe nanoparticles inhibited the growth of Serratia as well as the biosurfactant production when the concentration of the nanoparticles was higher than 10 mg/L. Fe nanoparticles showed inhibition effects to bacterial growth both after short time and long time interaction with Serratia, as well as to biosurfactant production when its concentration was higher than 100 mg/L. Based on the trends observed in this study, analytical models have been developed to predict the bacterial growth and biosurfactant production with varying concentrations of nanoparticles. - Highlights: • Modeled the effect of nanoparticles on the bacterial growth and biosurfactant production. • Effects of Au/Fe nonoparticles on Serratia Bacterial Growth and Production of Biosurfactant. • Scanning Electron Micrograph of bacteria-nanoparticles interaction.

Electrokinetic-Enhanced Remediation of Phenanthrene-Contaminated Soil Combined with Sphingomonas sp. GY2B and Biosurfactant.

Science.gov (United States)

Lin, Weijia; Guo, Chuling; Zhang, Hui; Liang, Xujun; Wei, Yanfu; Lu, Guining; Dang, Zhi

2016-04-01

Electrokinetic-microbial remediation (EMR) has emerged as a promising option for the removal of polycyclic aromatic hydrocarbons (PAHs) from contaminated soils. The aim of this study was to enhance degradation of phenanthrene (Phe)-contaminated soils using EMR combined with biosurfactants. The electrokinetic (EK) remediation, combined with Phe-degrading Sphingomonas sp. GY2B, and biosurfactant obtained by fermentation of Pseudomonas sp. MZ01, degraded Phe in the soil with an efficiency of up to 65.1 % at the anode, 49.9 % at the cathode after 5 days of the treatment. The presence of biosurfactants, electricity, and a neutral electrolyte stimulated the growth of the degrading bacteria as shown by a rapid increase in microbial biomass with time. The electrical conductivity and pH changed little during the course of the treatment, which benefitted the growth of microorganisms and the remediation of Phe-contaminated soil. The EMR system with the addition of biosurfactant had the highest Phe removal, demonstrating the biosurfactant may enhance the bioavailability of Phe and the interaction with the microorganism. This study suggests that the EMR combined with biosurfactants can be used to enhance in situ bioremediation of PAH-contaminated soils.

Biosurfactants prevent in vitro Candida albicans biofilm formation on resins and silicon materials for prosthetic devices.

Science.gov (United States)

Cochis, Andrea; Fracchia, Letizia; Martinotti, Maria Giovanna; Rimondini, Lia

2012-06-01

The aim of this study was to evaluate in vitro the preventive antiadhesion activity of biosurfactants against Candida albicans biofilm. Disks of silicon and acrylic resin for denture prostheses were precoated with increasing concentrations of biosurfactants obtained from endophyte biofilms selected from Robinia pseudoacacia and from Nerium oleander, and afterward infected with C. albicans cells. The number of biofilm cells were detected by colony-forming unit (CFU) counting, cell viability was established by the 2,3-bis(2-methoxy-4-nitro-5-sulphophenyl)-5-[(phenyl amino)carbonyl]-2H-tetrazolium hydroxide (XTT) assay, and biosurfactant cytotoxicity was evaluated by the [3-(4,5-dimethyliazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulphophenyl)-2H-tetrazolium] (MTT) assay. Chlorhexidine was used as control. Precoating with biosurfactants caused a greater reduction (P biosurfactants was observed at low concentrations (78.12 μg/mL and 156.12 μg/mL) which were noncytotoxic. This study demonstrated the preventive antiadhesion activity of biosurfactants against C. albicans biofilm. These agents are amphiphilic, interfere with microbial adhesion, and demonstrate cycompatibility with epithelial cells and fibroblasts. Copyright © 2012 Elsevier Inc. All rights reserved.

BIOSURFACTANT PRODUCTION BY THERMOPHILIC DAIRY STREPTOCOCCI

NARCIS (Netherlands)

BUSSCHER, HJ; NEU, TR; VANDERMEI, HC

Biosurfactant production of eight Streptococcus thermophilus strains, isolated from heat exchanger plates in the downstream side of the regenerator section of pasteurizers in the dairy industry has been measured using axisymmetric drop shape analysis by profile (ADSA-P). Strains were grown in M17

Potential biosurfactant producing endophytic and epiphytic fungi ...

African Journals Online (AJOL)

João Marcelo Lima

2016-06-15

Jun 15, 2016 ... L., macrophytes collected from oil-contaminated waters, were studied to assess their potential for ... personal hygiene products and food processing, among ... Biosurfactant production was undertaken in 50 mL of culture.

Alternatives for biosurfactants and bacteriocins extraction from Lactococcus lactis cultures produced under different pH conditions.

Science.gov (United States)

Rodríguez, N; Salgado, J M; Cortés, S; Domínguez, J M

2010-08-01

Study of the potential of Lactococcus lactis CECT-4434 as a biosurfactants and nisin (the only bacteriocin allowed to be used in the food industry) producer for industrial applications, exploiting the possibility of recovering separately both metabolites, taking into account that L. lactis is an interesting micro-organism with several applications in the food industry because it is recognized as GRAS. The results showed the ability of this strain to produce cell-bound biosurfactants, under controlled pH, and cell-bound biosurfactants and bacteriocins, when pH was not controlled. Three extraction procedures were designed to separately recover these substances. The strain L. lactis CECT-4434 showed to be a cell-bound biosurfactants and bacterocins producer when fermentations were carried out under uncontrolled pH. Both products can be recovered separately. Development of a convenient tool for the extraction of cell-bound biosurfactants and bacteriocins from the fermentation broth.

Kocuria marina BS-15 a biosurfactant producing halophilic bacteria isolated from solar salt works in India

Science.gov (United States)

Sarafin, Yesurethinam; Donio, Mariathasan Birdilla Selva; Velmurugan, Subramanian; Michaelbabu, Mariavincent; Citarasu, Thavasimuthu

2014-01-01

Biosurfactant screening was made among the eight halophilic bacterial genera isolated from Kovalam solar salt works in Kanyakumari of India. After initial screening, Kocuria sp. (Km), Kurthia sp. (Ku) and Halococcus sp. (Hc) were found to have positive biosurfactant activity. Biosurfactant derived from Kocuria sp. emulsified more than 50% of the crude oil, coconut oil, sunflower oil, olive oil and kerosene when compared to the other strains. Further, Kocuria marina BS-15 derived biosurfactant was purified and characterized by TLC, FTIR and GC–MS analysis. The TLC analysis revealed that, the purified biosurfactants belong to the lipopeptide group. The IR spectrum results revealed that functional groups are R2C 000000000000 000000000000 000000000000 111111111111 000000000000 111111111111 000000000000 000000000000 000000000000 NN, alkenes and N–H. The GC–MS analysis confirmed the compound as Nonanoic acid and Cyclopropane with the retention time of 12.78 and 24.65, respectively. PMID:25473358

SCREENING AND EXTRACTION OF BIOSURFACTANT PRODUCING BACTERIA FROM OIL CONTAMINATED SOILS.

OpenAIRE

B. F. Paul Beulah.

2018-01-01

Biosurfactants produced by bacteria are surface active compounds involved in the degradation of hydrocarbons. They are heterogeneous group of surface active molecules produced by microorganisms, which adhere to the cell surface or are excreted extra cellularly in the growth medium. The biosurfactants producing microbes are helpful in bioremediation of heavy metals, pesticides and hydrocarbon contaminated sites. They are also used as bio control agent to protect plant against various diseases,...

Biosurfactant and Degradative Enzymes Mediated Crude Oil Degradation by Bacterium Bacillus subtilis A1

Science.gov (United States)

Parthipan, Punniyakotti; Preetham, Elumalai; Machuca, Laura L.; Rahman, Pattanathu K. S. M.; Murugan, Kadarkarai; Rajasekar, Aruliah

2017-01-01

In this work, the biodegradation of the crude oil by the potential biosurfactant producing Bacillus subtilis A1 was investigated. The isolate had the ability to synthesize degradative enzymes such as alkane hydroxylase and alcohol dehydrogenase at the time of biodegradation of hydrocarbon. The biosurfactant producing conditions were optimized as pH 7.0, temperature 40°C, 2% sucrose and 3% of yeast extract as best carbon and nitrogen sources for maximum production of biosurfactant (4.85 g l-1). Specifically, the low molecular weight compounds, i.e., C10–C14 were completely degraded, while C15–C19 were degraded up to 97% from the total hydrocarbon pools. Overall crude oil degradation efficiency of the strain A1 was about 87% within a short period of time (7 days). The accumulated biosurfactant from the biodegradation medium was characterized to be lipopeptide in nature. The strain A1 was found to be more robust than other reported biosurfactant producing bacteria in degradation efficiency of crude oil due to their enzyme production capability and therefore can be used to remove the hydrocarbon pollutants from contaminated environment. PMID:28232826

Characterization of biosurfactants produced by Lactobacillus spp. and their activity against oral streptococci biofilm.

Science.gov (United States)

Ciandrini, Eleonora; Campana, Raffaella; Casettari, Luca; Perinelli, Diego R; Fagioli, Laura; Manti, Anita; Palmieri, Giovanni Filippo; Papa, Stefano; Baffone, Wally

2016-08-01

Lactic acid bacteria (LAB) can interfere with pathogens through different mechanisms; one is the production of biosurfactants, a group of surface-active molecules, which inhibit the growth of potential pathogens. In the present study, biosurfactants produced by Lactobacillus reuteri DSM 17938, Lactobacillus acidophilus DDS-1, Lactobacillus rhamnosus ATCC 53103, and Lactobacillus paracasei B21060 were dialyzed (1 and 6 kDa) and characterized in term of reduction of surface tension and emulsifying activity. Then, aliquots of the different dialyzed biosurfactants were added to Streptococcus mutans ATCC 25175 and Streptococcus oralis ATCC 9811 in the culture medium during the formation of biofilm on titanium surface and the efficacy was determined by agar plate count, biomass analyses, and flow cytometry. Dialyzed biosurfactants showed abilities to reduce surface tension and to emulsifying paraffin oil. Moreover, they significantly inhibited the adhesion and biofilm formation on titanium surface of S. mutans and S. oralis in a dose-dependent way, as demonstrated by the remarkable decrease of cfu/ml values and biomass production. The antimicrobial properties observed for dialyzed biosurfactants produced by the tested lactobacilli opens future prospects for their use against microorganisms responsible of oral diseases.

The effect of rhamnolipid biosurfactant produced by Pseudomonas fluorescens on model bacterial strains and isolates from industrial wastewater.

Science.gov (United States)

Vasileva-Tonkova, Evgenia; Sotirova, Anna; Galabova, Danka

2011-02-01

In this study, the effect of rhamnolipid biosurfactant produced by Pseudomonas fluorescens on bacterial strains, laboratory strains, and isolates from industrial wastewater was investigated. It was shown that biosurfactant, depending on the concentration, has a neutral or detrimental effect on the growth and protein release of model Gram (+) strain Bacillus subtilis 168. The growth and protein release of model Gram (-) strain Pseudomonas aeruginosa 1390 was not influenced by the presence of biosurfactant in the medium. Rhamnolipid biosurfactant at the used concentrations supported the growth of some slow growing on hexadecane bacterial isolates, members of the microbial community. Changes in cell surface hydrophobicity and permeability of some Gram (+) and Gram (-) isolates in the presence of rhamnolipid biosurfactant were followed in experiments in vitro. It was found that bacterial cells treated with biosurfactant became more or less hydrophobic than untreated cells depending on individual characteristics and abilities of the strains. For all treated strains, an increase in the amount of released protein was observed with increasing the amount of biosurfactant, probably due to increased cell permeability as a result of changes in the organization of cell surface structures. The results obtained could contribute to clarify the relationships between members of the microbial community as well as suggest the efficiency of surface properties of rhamnolipid biosurfactant from Pseudomonas fluorescens making it potentially applicable in bioremediation of hydrocarbon-polluted environments.

Biosurfactant production by Mucor circinelloides on waste frying oil and possible uses in crude oil remediation.

Science.gov (United States)

Hasanizadeh, Parvin; Moghimi, Hamid; Hamedi, Javad

2017-10-01

Biosurfactants are biocompatible surface active agents which many microorganisms produce. This study investigated the production of biosurfactants by Mucor circinelloides. The effects of different factors on biosurfactant production, including carbon sources and concentrations, nitrogen sources, and iron (II) concentration, were studied and the optimum condition determined. Finally, the strain's ability to remove the crude oil and its relationship with biosurfactant production was evaluated. The results showed that M. circinelloides could reduce the surface tension of the culture medium to 26.6 mN/m and create a clear zone of 12.9 cm diameter in an oil-spreading test. The maximum surface tension reduction was recorded 3 days after incubation. The optimum condition for biosurfactant production was achieved in the presence of 8% waste frying oil as a carbon source, 2 g/L yeast extract as a nitrogen source, and 0.01 mM FeSO 4 . M. circinelloides could consume 8% waste frying oil in 5 days of incubation, and 87.6% crude oil in 12 days of incubation. A direct correlation was observed between oil degradation and surface tension reduction in the first 3 days of fungal growth. The results showed that the waste frying oil could be recommended as an inexpensive oily waste substance for biosurfactant production, and M. circinelloides could have the potential to treat waste frying oil. According to the results, the produced crude biosurfactant or fungal strain could be directly used for the mycoremediation of crude oil contamination in oil fields.

Characterization of biosurfactant produced from submerged ...

African Journals Online (AJOL)

user

interfacial tension. This work was designed to produce biosurfactants from the fermentation of .... The cashew apples were collected from. Ubogidi cashew ... and manually crushed to remove the juice using a pestle and mortar. The bagasse was ..... degradation by yeast species Trichosporon asahii isolated from petroleum ...

High-Level Culturability of Epiphytic Bacteria and Frequency of Biosurfactant Producers on Leaves

Science.gov (United States)

Burch, Adrien Y.; Do, Paulina T.; Sbodio, Adrian; Suslow, Trevor V.

2016-01-01

ABSTRACT To better characterize the bacterial community members capable of biosurfactant production on leaves, we distinguished culturable biosurfactant-producing bacteria from nonproducers and used community sequencing to compare the composition of these distinct cultured populations with that from DNA directly recovered from leaves. Communities on spinach, romaine, and head lettuce leaves were compared with communities from adjacent samples of soil and irrigation source water. Soil communities were poorly described by culturing, with recovery of cultured representatives from only 21% of the prevalent operational taxonomic units (OTUs) (>0.2% reads) identified. The dominant biosurfactant producers cultured from soil included bacilli and pseudomonads. In contrast, the cultured communities from leaves are highly representative of the culture-independent communities, with over 85% of the prevalent OTUs recovered. The dominant taxa of surfactant producers from leaves were pseudomonads as well as members of the infrequently studied genus Chryseobacterium. The proportions of bacteria cultured from head lettuce and romaine leaves that produce biosurfactants were directly correlated with the culture-independent proportion of pseudomonads in a given sample, whereas spinach harbored a wider diversity of biosurfactant producers. A subset of the culturable bacteria in irrigation water also became enriched on romaine leaves that were irrigated overhead. Although our study was designed to identify surfactant producers on plants, we also provide evidence that most bacteria in some habitats, such as agronomic plant surfaces, are culturable, and these communities can be readily investigated and described by more classical culturing methods. IMPORTANCE The importance of biosurfactant production to the bacteria that live on waxy leaf surfaces as well as their ability to be accurately assessed using culture-based methodologies was determined by interrogating epiphytic populations by

Improved Energy Recovery by Anaerobic Grey Water Sludge Treatment with Black Water

OpenAIRE

Tervahauta, Taina; Bryant, Isaac; Leal, Lucía; Buisman, Cees; Zeeman, Grietje

2014-01-01

This study presents the potential of combining anaerobic grey water sludge treatment with black water in an up-flow anaerobic sludge blanket (UASB) reactor to improve energy recovery within source-separated sanitation concepts. Black water and the mixture of black water and grey water sludge were compared in terms of biochemical methane potential (BMP), UASB reactor performance, chemical oxygen demand (COD) mass balance and methanization. Grey water sludge treatment with black water increased...

Properties of a biosurfactant produced by Bacillus pumilus using vinasse and waste frying oil as alternative carbon sources

Directory of Open Access Journals (Sweden)

Juliana Guerra de Oliveira

2013-02-01

Full Text Available Biosurfactants are chemical molecules produced by the microorganisms with potential for application in various industrial and environmental sectors. The production parameters and the physicochemical properties of a biosurfactant synthesized by Bacillus pumilus using different concentrations of vinasse and waste frying oil as alternative carbon sources were analyzed. The microorganism was able to grow and produce a biosurfactant using both the residues. The surface tension was reduced up to 45 mN/m and the maximum production of crude biosurfactant was 27.7 and 5.7 g/l for vinasse and waste frying oil, respectively, in concentration of 5%. The critical micelle concentration (CMC results of 1.5 and 0.2 g/l showed the efficiency of the biosurfactant produced on both the substrates. The results showed that the alternative substrates could be used for the production of an efficient biosurfactant by B. pumilus. These properties have potential for industrial and environmental applications.

Diversity and activity of biosurfactant-producing Pseudomonas in the rhizosphere of black pepper in Vietnam.

Science.gov (United States)

Tran, H; Kruijt, M; Raaijmakers, J M

2008-03-01

Phytophthora capsici is a major pathogen of black pepper and zoospores play an important role in the infection process. Fluorescent pseudomonads that produce biosurfactants with zoosporicidal activities were isolated from the black pepper rhizosphere in Vietnam, and their genotypic diversity and potential to control Phy. capsici root rot was determined. Biosurfactant-producing pseudomonads were genotypically and biochemically characterized by BOX-polymerase chain reaction (PCR), 16S-rDNA sequencing, reverse-phase-high-performance liquid chromatography and liquid chromatography-mass spectrometry analyses. Biosurfactant-producing fluorescent pseudomonads make up c. 1.3% of the culturable Pseudomonas population in the rhizosphere of black pepper. Although BOX-PCR revealed substantial genotypic diversity, the isolates were shown to produce the same biosurfactants and were all identified as Pseudomonas putida. When applied to black pepper stem cuttings, several of the biosurfactant-producing strains provided significant disease control. In absence of the disease, several of the bacterial strains promoted shoot and root growth of black pepper stem cuttings. Biosurfactant-producing pseudomonads indigenous to the rhizosphere of black pepper plants are genotypically diverse and provide a novel resource for the control of Phy. capsici root rot and growth promotion of black pepper stem cuttings. The results of this study provide a strong basis for further development of supplementary strategies with antagonistic bacteria to control foot and root rot of black pepper and to promote plant growth.

Biosurfactant Production by Cultivation of Bacillus atrophaeus ATCC 9372 in Semidefined Glucose/Casein-Based Media

Science.gov (United States)

Das Neves, Luiz Carlos Martins; de Oliveira, Kátia Silva; Kobayashi, Márcio Junji; Vessoni Penna, Thereza Christina; Converti, Attilio

Biosurfactants are proteins with detergent, emulsifier, and antimicrobial actions that have potential application in environmental applications such as the treatment of organic pollutants and oil recovery. Bacillus atrophaeus strains are nonpathogenic and are suitable source of biosurfactants, among which is surfactin. The aim of this work is to establish a culture medium composition able to stimulate biosurfactants production by B. atrophaeus ATCC 9372. Batch cultivations were carried out in a rotary shaker at 150 rpm and 35°C for 24 h on glucose- and/or casein-based semidefined culture media also containing sodium chloride, dibasic sodium phosphate, and soy flour. The addition of 14.0 g/L glucose in a culture medium containing 10.0 g/L of casein resulted in 17 times higher biosurfactant production (B max=635.0 mg/L). Besides, the simultaneous presence of digested casein (10.0 g/L), digested soy flour (3.0 g/L), and glucose (18.0 g/L) in the medium was responsible for a diauxic effect during cell growth. Once the diauxie started, the average biosurfactants concentration was 16.8% less than that observed before this phenomenon. The capability of B. atrophaeus strain to adapt its own metabolism to use several nutrients as energy sources and to preserve high levels of biosurfactants in the medium during the stationary phase is a promising feature for its possible application in biological treatments.

Going Green and Cold: Biosurfactants from Low-Temperature Environments to Biotechnology Applications.

Science.gov (United States)

Perfumo, Amedea; Banat, Ibrahim M; Marchant, Roger

2018-03-01

Approximately 80% of the Earth's biosphere is cold, at an average temperature of 5°C, and is populated by a diversity of microorganisms that are a precious source of molecules with high biotechnological potential. Biosurfactants from cold-adapted organisms can interact with multiple physical phases - water, ice, hydrophobic compounds, and gases - at low and freezing temperatures and be used in sustainable (green) and low-energy-impact (cold) products and processes. We review the biodiversity of microbial biosurfactants produced in cold habitats and provide a perspective on the most promising future applications in environmental and industrial technologies. Finally, we encourage exploring the cryosphere for novel types of biosurfactants via both culture screening and functional metagenomics. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cytotoxic effect of microbial biosurfactants against human embryonic kidney cancerous cell: HEK-293 and their possible role in apoptosis.

Science.gov (United States)

Pradhan, Arun Kumar; Pradhan, Nilotpala; Mohapatra, Purusottam; Kundu, Chanakya Nath; Panda, Prasanna Kumar; Mishra, Barada Kanta

2014-11-01

Two different microbial biosurfactants S9BS and CHBS were isolated from Lysinibacillus fusiformis S9 and Bacillus tequilensis CH. Cytotoxicity effect of these biosurfactants on human embryonic kidney cancerous cell (HEK-293) were studied with the help of 3-(4,5-dimethylthiazol-2yl-)-2, 5-diphenyl tetrazolium bromide (MTT) assay and morphological changes were observed under inverted microscope. The biosurfactants exhibited positive cytotoxic effect on HEK-293 cell line. It was found that LC50 of S9BS and CHBS were 75 and 100 μg ml(-1), respectively. Further cell cycle and apoptosis analysis of biosurfactant-treated HEK-293 cell line were done by FACS. In this study, cytotoxic effect of glycolipid biosurfactant against HEK-293 cell lines is reported for the first time. Mechanism towards increased membrane permeability of biosurfactant-treated cancer cell may be the incorporation of its lipid moiety into the plasma membrane leading to formation of pores and membrane disruption. Hence, these microbial biosurfactants can prove to be significant biomolecule for cancer treatment.

Biosurfactant Production by Rhodococcus Erythropolis and its Application to Oil Removal

OpenAIRE

Pacheco, Graziela Jardim; Ciapina, Elisa Mara Prioli; Gomes, Edelvio de Barros; Junior, Nei Pereira

2010-01-01

The influence of different nutrients on biosurfactant production by Rhodococcus erythropolis was investigated. Increasing the concentration of phosphate buffer from 30 up through 150 mmol/L stimulated an increase in biosurfactant production, which reached a maximum concentration of 285 mg/L in shaken flasks. Statistical analysis showed that glycerol, NaNO3, MgSO4 and yeast extract had significant effects on production. The results were confirmed in a batchwise bioreactor, and semi-growth-asso...

Characterization of Biosurfactant Produced during Degradation of Hydrocarbons Using Crude Oil As Sole Source of Carbon.

Science.gov (United States)

Patowary, Kaustuvmani; Patowary, Rupshikha; Kalita, Mohan C; Deka, Suresh

2017-01-01

Production and spillage of petroleum hydrocarbons which is the most versatile energy resource causes disastrous environmental pollution. Elevated oil degrading performance from microorganisms is demanded for successful microbial remediation of those toxic pollutants. The employment of biosurfactant-producing and hydrocarbon-utilizing microbes enhances the effectiveness of bioremediation as biosurfactant plays a key role by making hydrocarbons bio-available for degradation. The present study aimed the isolation of a potent biosurfactant producing indigenous bacteria which can be employed for crude oil remediation, along with the characterization of the biosurfactant produced during crude oil biodegradation. A potent bacterial strain Pseudomonas aeruginosa PG1 (identified by 16s rDNA sequencing) was isolated from hydrocarbon contaminated soil that could efficiently produce biosurfactant by utilizing crude oil components as the carbon source, thereby leading to the enhanced degradation of the petroleum hydrocarbons. Strain PG1 could degrade 81.8% of total petroleum hydrocarbons (TPH) after 5 weeks of culture when grown in mineral salt media (MSM) supplemented with 2% (v/v) crude oil as the sole carbon source. GCMS analysis of the treated crude oil samples revealed that P. aeruginosa PG1 could potentially degrade various hydrocarbon contents including various PAHs present in the crude oil. Biosurfactant produced by strain PG1 in the course of crude oil degradation, promotes the reduction of surface tension (ST) of the culture medium from 51.8 to 29.6 mN m -1 , with the critical micelle concentration (CMC) of 56 mg L -1 . FTIR, LC-MS, and SEM-EDS studies revealed that the biosurfactant is a rhamnolipid comprising of both mono and di rhamnolipid congeners. The biosurfactant did not exhibit any cytotoxic effect to mouse L292 fibroblastic cell line, however, strong antibiotic activity against some pathogenic bacteria and fungus was observed.

Characterization of Biosurfactant Produced during Degradation of Hydrocarbons Using Crude Oil As Sole Source of Carbon

Science.gov (United States)

Patowary, Kaustuvmani; Patowary, Rupshikha; Kalita, Mohan C.; Deka, Suresh

2017-01-01

Production and spillage of petroleum hydrocarbons which is the most versatile energy resource causes disastrous environmental pollution. Elevated oil degrading performance from microorganisms is demanded for successful microbial remediation of those toxic pollutants. The employment of biosurfactant-producing and hydrocarbon-utilizing microbes enhances the effectiveness of bioremediation as biosurfactant plays a key role by making hydrocarbons bio-available for degradation. The present study aimed the isolation of a potent biosurfactant producing indigenous bacteria which can be employed for crude oil remediation, along with the characterization of the biosurfactant produced during crude oil biodegradation. A potent bacterial strain Pseudomonas aeruginosa PG1 (identified by 16s rDNA sequencing) was isolated from hydrocarbon contaminated soil that could efficiently produce biosurfactant by utilizing crude oil components as the carbon source, thereby leading to the enhanced degradation of the petroleum hydrocarbons. Strain PG1 could degrade 81.8% of total petroleum hydrocarbons (TPH) after 5 weeks of culture when grown in mineral salt media (MSM) supplemented with 2% (v/v) crude oil as the sole carbon source. GCMS analysis of the treated crude oil samples revealed that P. aeruginosa PG1 could potentially degrade various hydrocarbon contents including various PAHs present in the crude oil. Biosurfactant produced by strain PG1 in the course of crude oil degradation, promotes the reduction of surface tension (ST) of the culture medium from 51.8 to 29.6 mN m−1, with the critical micelle concentration (CMC) of 56 mg L−1. FTIR, LC-MS, and SEM-EDS studies revealed that the biosurfactant is a rhamnolipid comprising of both mono and di rhamnolipid congeners. The biosurfactant did not exhibit any cytotoxic effect to mouse L292 fibroblastic cell line, however, strong antibiotic activity against some pathogenic bacteria and fungus was observed. PMID:28275373

Production of Biosurfactants by Actinomycetes Isolated from ...

African Journals Online (AJOL)

ASPIRE ONE D270

biosurfactants are stable across temperature ranges and are not majorly affected by salt concentration; this property aids its potential ... for restoration of soil because the technology is ... technology is also dependent upon a microbial ability to ...

Isolation and characterization of biosurfactant/bioemulsifier-producing bacteria from petroleum contaminated sites.

Science.gov (United States)

Batista, S B; Mounteer, A H; Amorim, F R; Tótola, M R

2006-04-01

Biosurfactant-producing bacteria were isolated from terrestrial and marine samples collected in areas contaminated with crude oil or its byproducts. Isolates were screened for biosurfactant/bioemulsifier production in different carbon sources (glucose, fructose, sucrose and kerosene) using the qualitative drop-collapse test. Glucose produced the highest number of positive results (17 of 185 isolates). All 17 isolates produced emulsions with kerosene and 12 exhibited high emulsion-stabilizing capacity, maintaining 50% of the original emulsion volume for 48 h. Eight of the 17 isolates reduced the growth medium surface tension below 40 mN m(-1) with 5 exhibiting this capacity in cell-free filtrates. Onset of biosurfactant production differed among the isolates, with some initiating synthesis during the exponential growth phase and others after the stationary phase was reached. Increasing temperature from 25 to 35 degrees C accelerated onset of biosurfactant production in only two isolates while pH (6.5-7.6) had no effect in any isolate tested. Isolation from petroleum contaminated sites using the screening protocol presented proved to be a rapid and effective manner to identify bacterial isolates with potential industrial applications.

Algal and microbial exopolysaccharides: new insights as biosurfactants and bioemulsifiers.

Science.gov (United States)

Paniagua-Michel, José de Jesús; Olmos-Soto, Jorge; Morales-Guerrero, Eduardo Roberto

2014-01-01

Currently, efforts are being made to utilize more natural biological systems as alternatives as a way to replace fossil forms of carbon. There is a growing concern at global level to have nontoxic, nonhazardous surface-active agents; contrary to synthetic surfactants, their biological counterparts or biosurfactants play a primary function, facilitating microbial presence in environments dominated by hydrophilic-hydrophobic interfaces. Algal and microbial biosurfactants/bioemulsifiers from marine and deep-sea environments are attracting major interest due to their structural and functional diversity as molecules actives of surface and an alternative biomass to replace fossil forms of carbon. Algal and microbial surfactants are lipid in nature and classified as glycolipids, phospholipids, lipopeptides, natural lipids, fatty acids, and lipopolysaccharides. These metabolic bioactive products are applicable in a number of industries and processes, viz., food processing, pharmacology, and bioremediation of oil-polluted environments. This chapter presents an update of the progress and potentialities of the principal producers of exopolysaccharide (EPS)-type biosurfactants and bioemulsifiers, viz., macro- and microalgae (cyanobacteria and diatoms) and bacteria from marine and extreme environments. Particular interest is centered into new sources and applications, viz., marine and deep-sea environments and promissory uses of these EPSs as biosurfactants/emulsifiers and other polymeric roles. The enormous benefits of these molecules encourage their discovery, exploitation, and development of new microbial EPSs that could possess novel industrial importance and corresponding innovations. © 2014 Elsevier Inc. All rights reserved.

Biosurfactant production by the crude oil degrading Stenotrophomonas sp. B-2: chemical characterization, biological activities and environmental applications.

Science.gov (United States)

Gargouri, Boutheina; Contreras, María Del Mar; Ammar, Sonda; Segura-Carretero, Antonio; Bouaziz, Mohamed

2017-02-01

In this work, biosurfactant-producing microorganisms were isolated from hydrocarbon-contaminated water collected from Tunisian oilfield. After enrichment and isolation, different bacterial strains were preliminary studied for their biosurfactant/bioemulsifier properties when using crude oil as the unique carbon source. In particular, the isolate strain B-2, a Gram-negative, rod-shaped bacterium, efficiently emulsified crude oil. The extracellular biosurfactant product from this strain presented an emulsification activity above 70% and a hydrophobicity of 71%. In addition, a diameter of 6 cm was observed in the oil displacement test. The characterization of B-2 strain using 16S rDNA sequencing enables us to find a high degree of similarity with various members of the genus Stenotrophomonas (with a percentage of similarity of 99%). The emulsification activity of Stenotrophomonas biosurfactant B-2 was maintained in a wide range of pH (2 to 6), temperature (4 to 55 °C), and salinity (0 to 50 g L -1 ) conditions. It also enhanced the solubility of phenanthrene in water and could be used in the re-mobilization of hydrocarbon-contaminated environment. In addition, this biosurfactant exhibited antimicrobial and antioxidant properties. Infrared spectroscopy suggested potential lipidic and peptidic moieties, and mass spectrometry-based analyses showed that the biosurfactant contains mainly cyclic peptidic structures belonging to the class of diketopiperazines. Therefore, the B-2 strain is a promising biosurfactant-producing microorganism and its derived biosurfactant presents a wide range of industrial applications.

Interactive optimization of biosurfactant production by Paenibacillus alvei ARN63 isolated from an Iranian oil well.

Science.gov (United States)

Najafi, A R; Rahimpour, M R; Jahanmiri, A H; Roostaazad, R; Arabian, D; Soleimani, M; Jamshidnejad, Z

2011-01-01

The potential of an indigenous bacterial strain isolated from an Iranian oil field for the production of biosurfactant was investigated in this study. After isolation, the bacterium was characterized to be Paenibacillus alvei by biochemical tests and 16S ribotyping. The biosurfactant, which was produced by this bacterium, was able to lower the surface tension of media to 35 mN/m. Accordingly, thin layer chromatography (TLC) and FT-IR has been carried out to determine compositional analysis of the produced biosurfactant. After all the tests related to characterization of the biosurfactant produced by the isolated bacterium, it was characterized as lipopeptide derivative. The combination of central composite rotatable design (CCRD) and response surface methodology (RSM) was exploited to optimize biosurfactant production. Therefore, variations of four impressive parameters, pH, temperature, glucose and salinity concentrations were selected for optimization of growth conditions. The empirical model developed through RSM in terms of effective operational factors mentioned above was found to be adequate to describe the biosurfactant production. A maximum reduction in surface tension was obtained under the optimal conditions of 13.03 g/l glucose concentration, 34.76 °C, 51.39 g/l total salt concentration and medium pH 6.89. Copyright © 2010 Elsevier B.V. All rights reserved.

Evaluation of substrates from renewable-resources in biosurfactants ...

African Journals Online (AJOL)

Evaluation of substrates from renewable-resources in biosurfactants production by Pseudomonas strains. Sidnei Cerqueira dos Santos, Luzimar Gonzaga Fernandez, Juan Carlos Rossi-Alva, Milton Ricardo de Abreu Roque ...

Isolation and Characterization of Biosurfactant Producing Bacteria for the Application in Enhanced Oil Recovery

Science.gov (United States)

Prasad, Niraj; Dasgupta, Sumita; Chakraborty, Mousumi; Gupta, Smita

2017-07-01

In the present study, a biosurfactant producing bacterial strain was isolated, screened and identified. Further, various fermentation conditions (such as pH (5-10), incubation period (24-96h) and incubation temperature (20-60 °C) were optimized for maximum production of biosurfactant. The produced biosurfactant was characterized by measuring emulsification index, foaming characteristics, rhamnolipid detection, interfacial tension between water and oil and stability against pH and temperature for its potential application in oil recovery process. The additional oil recovery for two different sand, sand1 and sand2, was found to be 49% and 38%, respectively.

Development of More Effective Biosurfactants for Enhanced Oil Recovery/Advanced Recovery Concepts Awards; SEMIANNUAL

International Nuclear Information System (INIS)

McInerney, M.J.; Marsh, T.L.; Zhang, X.; Knapp, R.M.; Nagle, Jr. D.P.; Sharma, P.K.; Jackson, B.E.

2002-01-01

The objectives of this were two fold. First, core displacement studies were done to determine whether microbial processes could recover residual oil at elevated pressures. Second, the importance of biosurfactant production for the recovery of residual oil was studies. In these studies, a biosurfactant-producing, microorganisms called Bacillus licheniformis strain JF-2 was used. This bacterium produces a cyclic peptide biosurfactant that significantly reduces the interfacial tension between oil and brine (7). The use of a mutant deficient in surfactant production and a mathematical MEOR simulator were used to determine the major mechanisms of oil recovery by these two strains

Correlation between Biosurfactants and Antifungal Activity of a Biocontrol Bacterium, Bacillus amyloliquefaciens LM11

Directory of Open Access Journals (Sweden)

Beom Ryong Kang

2017-06-01

Full Text Available Bacillus amyloliquefaciens LM11 was isolated from the feces of larvae of the rhino beetle and showed strong antifungal activities against various phytopathogenic fungi by producing biosurfactants. In this study, our overall goal was to determine relationship between biosurfactants produced from the LM11 strain and its role in growth inhibition of phytopathogenic fungi. Production and expression levels of B. amyloliquefaciens LM11 biosurfactants were significantly differed depending on growth phases. Transcriptional and biochemical analysis indicated that the biosurfactants of the LM11 strain were greatly enhanced in late log-phase to stationary phase. Inhibitions of phytopathogenic mycelial growth and spore germination were directly correlated (P<0.001, R=0.761 with concentrations of the LM11 cell-free culture filtrates. The minimum inhibitory surface tension of the culture filtrate of the B. amyloliquefaciens LM11 grown in stationary phase to inhibit mycelial growth of the phytopathogenic fungi was 38.5 mN/m (P<0.001, R=0.951–0.977. Our results indicated that the biosurfactants of B. amyloliquefaciens LM11 act as key antifungal metabolites in biocontrol of plant diseases, and measuring surface tension of the cell-free culture fluids can be used as an easy indicator for optimal usage of the biocontrol agents.

Production and antimicrobial property of glycolipid biosurfactants

Science.gov (United States)

Microbial glycolipids such as rhamnolipid (RL) and sophorolipid (SL) are an important class of biosurfactants with excellent surface tension-lowering activity. Besides their surfactant- and environment-friendly properties, however, additional value-added property such as bacteriocidal activity is n...

Infrared spectroscopy for studying structure and aging effects in rhamnolipid biosurfactants

OpenAIRE

Kiefer, Johannes; Radzuan, Mohd Nazren; Winterburn, James

2017-01-01

Biosurfactants are produced by microorganisms and represent amphiphilic compounds with polar and non-polar moieties; hence they can be used to stabilize emulsions, e.g. in the cosmetic and food sectors. Their structure and its changes when exposed to light and elevated temperature are yet to be fully understood. In this study, we demonstrate that attenuated total reflection infrared (ATR-IR) spectroscopy is a useful tool for the analysis of biosurfactants, using rhamnolipids produced by ferme...

Screening of biosurfactant producers from petroleum hydrocarbon contaminated sources in cold marine environments.

Science.gov (United States)

Cai, Qinhong; Zhang, Baiyu; Chen, Bing; Zhu, Zhiwen; Lin, Weiyun; Cao, Tong

2014-09-15

An overview of literature about isolating biosurfactant producers from marine sources indicated no such producers have been reported form North Atlantic Canada. Water and sediment samples were taken from petroleum hydrocarbon contaminated coastal and offshore areas in this region. Either n-hexadecane or diesel was used as the sole carbon source for the screening. A modified colony-based oil drop collapsing test was used to cover sessile biosurfactant producers. Fifty-five biosurfactant producers belong to genera of Alcanivorax, Exiguobacterium, Halomonas, Rhodococcus, Bacillus, Acinetobacter, Pseudomonas, and Streptomyces were isolated. The first three genera were established after 1980s with interesting characteristics and limited relevant publications. Some of the 55 isolated strains were found with properties such as greatly reducing surface tension, stabilizing emulsion and producing flocculant. Isolates P6-4P and P1-5P were selected to demonstrate the performance of biosurfactant production, and were found to reduce the surface tension of water to as low as 28 dynes/cm. Copyright © 2014 Elsevier Ltd. All rights reserved.

Functional, genetic and chemical characterization of biosurfactants produced by plant growth-promoting Pseudomonas putida 267

NARCIS (Netherlands)

Kruijt, M.; Tran, H.; Raaijmakers, J.M.

2009-01-01

Aims: Plant growth-promoting Pseudomonas putida strain 267, originally isolated from the rhizosphere of black pepper, produces biosurfactants that cause lysis of zoospores of the oomycete pathogen Phytophthora capsici. The biosurfactants were characterized, the biosynthesis gene(s) partially

Catalysis of gas hydrates by biosurfactants in seawater-saturated sand/clay

Energy Technology Data Exchange (ETDEWEB)

Rogers, R. E.; Kothapalli, C.; Lee, M.S. [Mississippi State University, Swalm School of Chemical Engineering, MS (United States); Woolsey, J. R. [University of Mississippi, Centre of Marine Resources and Environmental Technology, MS (United States)

2003-10-01

Large gas hydrate mounds have been photographed in the seabed of the Gulf of Mexico and elsewhere. According to industry experts, the carbon trapped within gas hydrates is two or three times greater than all known crude oil, natural gas and coal reserves in the world. Gas hydrates, which are ice-like solids formed from the hydrogen bonding of water as water temperature is lowered under pressure to entrap a suitable molecular-size gas in cavities of the developing crystal structure, are found below the ocean floor to depths exhibiting temperature and pressure combinations within the appropriate limits. The experiments described in this study attempt to ascertain whether biosurfactant byproducts of microbial activity in seabeds could catalyze gas hydrate formation. Samples of five possible biosurfactants classifications were used in the experiments. Results showed that biosurfactants enhanced hydrate formation rate between 96 per cent and 288 percent, and reduced hydrate induction time 20 per cent to 71 per cent relative to the control. The critical micellar concentration of rhamnolipid/seawater solution was found to be 13 ppm at hydrate-forming conditions. On the basis of these results it was concluded that minimal microbial activity in sea floor sands could achieve the threshold concentration of biosurfactant that would greatly promote hydrate formation. 28 refs., 2 tabs., 4 figs.

Biosurfactants production by yeasts using soybean oil and glycerol as low cost substrate.

Science.gov (United States)

Accorsini, Fábio Raphael; Mutton, Márcia Justino Rossini; Lemos, Eliana Gertrudes Macedo; Benincasa, Maria

2012-01-01

Biosurfactants are bioactive agents that can be produced by many different microorganisms. Among those, special attention is given to yeasts, since they can produce many types of biosurfactants in large scale, using several kinds of substrates, justifying its use for industrial production of those products. For this production to be economically viable, the use of residual carbon sources is recommended. The present study isolated yeasts from soil contaminated with petroleum oil hydrocarbons and assessed their capacity for producing biosurfactants in low cost substrates. From a microbial consortium enriched, seven yeasts were isolated, all showing potential for producing biosurfactants in soybean oil. The isolate LBPF 3, characterized as Candida antarctica, obtained the highest levels of production - with a final production of 13.86 g/L. The isolate LBPF 9, using glycerol carbon source, obtained the highest reduction in surface tension in the growth medium: approximately 43% of reduction after 24 hours of incubation. The products obtained by the isolates presented surfactant activity, which reduced water surface tension to values that varied from 34 mN/m, obtained from the product of isolates LBPF 3 and 16 LBPF 7 (respectively characterized as Candida antarctica and Candida albicans) to 43 mN/m from the isolate LPPF 9, using glycerol as substrate. The assessed isolates all showed potential for the production of biosurfactants in conventional sources of carbon as well as in agroindustrial residue, especially in glycerol.

Biosurfactants production by yeasts using soybean oil and glycerol as low cost substrate

Directory of Open Access Journals (Sweden)

Fábio Raphael Accorsini

2012-03-01

Full Text Available Biosurfactants are bioactive agents that can be produced by many different microorganisms. Among those, special attention is given to yeasts, since they can produce many types of biosurfactants in large scale, using several kinds of substrates, justifying its use for industrial production of those products. For this production to be economically viable, the use of residual carbon sources is recommended. The present study isolated yeasts from soil contaminated with petroleum oil hydrocarbons and assessed their capacity for producing biosurfactants in low cost substrates. From a microbial consortium enriched, seven yeasts were isolated, all showing potential for producing biosurfactants in soybean oil. The isolate LBPF 3, characterized as Candida antarctica, obtained the highest levels of production - with a final production of 13.86 g/L. The isolate LBPF 9, using glycerol carbon source, obtained the highest reduction in surface tension in the growth medium: approximately 43% of reduction after 24 hours of incubation. The products obtained by the isolates presented surfactant activity, which reduced water surface tension to values that varied from 34 mN/m, obtained from the product of isolates LBPF 3 and 16 LBPF 7 (respectively characterized as Candida antarctica and Candida albicans to 43 mN/m from the isolate LPPF 9, using glycerol as substrate. The assessed isolates all showed potential for the production of biosurfactants in conventional sources of carbon as well as in agroindustrial residue, especially in glycerol.

Kinetic study of biosurfactant production by Bacillus subtilis LAMI005 grown in clarified cashew apple juice.

Science.gov (United States)

de Oliveira, Darlane Wellen Freitas; França, Italo Waldimiro Lima; Félix, Anne Kamilly Nogueira; Martins, João Jeferson Lima; Giro, Maria Estela Aparecida; Melo, Vânia Maria M; Gonçalves, Luciana Rocha Barros

2013-01-01

In this work a low cost medium for the production of a biosurfactant by Bacillus subtilis LAMI005 and the kinetics of surfactin production considering the effect of initial substrate concentration were investigated. First, cashew apple juice supplementation for optimal production of biosurfactant by B. subtilis LAMI005 was studied. The medium formulated with clarified cashew apple juice and distilled water, supplemented with 1.0 g/L of (NH(4))(2)SO(4), proved to be the best among the nutrients evaluated. The crude biosurfactant had the ability to decrease the surface tension of water to 30 dyne/cm, with a critical micelle concentration (CMC) of 63.0 mg/L. Emulsification experiments indicated that this biosurfactant effectively emulsified kerosene (IE(24)=67%) and soybean oil (IE(24)=64%). Furthermore, the emulsion stability was always very high. It was shown by biochemical analysis, IR spectra, that there is no qualitative differences in the composition of the crude biosurfactant from a standard sample of surfactin from B. subtilis. Copyright © 2012 Elsevier B.V. All rights reserved.

Production of biosurfactant by Pseudomonas spp. isolated from industrial waste in Turkey

OpenAIRE

KAYA, Tayfun; ASLIM, Belma; KARİPTAŞ, Ergin

2014-01-01

In this study, 26 Pseudomonas spp. were isolated from a stream polluted by factory waste and from petroleum-contaminated soil. The surface tension (ST) of the cultures was used as a criterion for the primary isolation of biosurfactant-producing bacteria. Biosurfactant production was quantified by ST reduction, critical micelle concentration (CMC), emulsification capacity (EC), and cell surface hydrophobicity (CSH). Two of the isolates, P. aeruginosa 78 and 99, produced rhamnolipid biosurfacta...

Response surface optimization of the medium components for the production of biosurfactants by probiotic bacteria

NARCIS (Netherlands)

Rodrigues, L; Teixeira, J; Oliveira, R; van der Mei, HC

Optimization of the medium for biosurfactants production by probiotic bacteria (Lactococcus lactis 53 and Streptococcus thermophilus A) was carried out using response surface methodology. Both biosurfactants were proved to be growth-associated, thus the desired response selected for the optimization

Management of soybean oil refinery wastes through recycling them for producing biosurfactant using Pseudomonas aeruginosa MR01.

Science.gov (United States)

Partovi, Maryam; Lotfabad, Tayebe Bagheri; Roostaazad, Reza; Bahmaei, Manochehr; Tayyebi, Shokoufe

2013-06-01

Biosurfactant production through a fermentation process involving the biodegradation of soybean oil refining wastes was studied. Pseudomonas aeruginosa MR01 was able to produce extracellular biosurfactant when it was cultured in three soybean oil refinement wastes; acid oil, deodorizer distillate and soapstock, at different carbon to nitrogen ratios. Subsequent fermentation kinetics in the three types of waste culture were also investigated and compared with kinetic behavior in soybean oil medium. Biodegradation of wastes, biosurfactant production, biomass growth, nitrate consumption and the number of colony forming units were detected in four proposed media, at specified time intervals. Unexpectedly, wastes could stimulate the biodegradation activity of MR01 bacterial cells and thus biosurfactant synthesis beyond that of the refined soybean oil. This is evident from higher yields of biodegradation and production, as revealed in the waste cultures (Ydeg|(Soybean oil) = 53.9 % YP/S|(Soybean oil) = 0.31 g g(-1), respectively). Although production yields were approximately the same in the three waste cultures (YP/S|(wastes) =/~ 0.5 g g(-1)), microbial activity resulted in higher yields of biodegradation (96.5 ± 1.13 %), maximum specific growth rate (μ max = 0.26 ± 0.02 h(-1)), and biosurfactant purity (89.6 %) with a productivity of 14.55 ± 1.10 g l(-1), during the bioconversion of soapstock into biosurfactant. Consequently, applying soybean oil soapstock as a substrate for the production of biosurfactant with commercial value has the potential to provide a combination of economical production with environmental protection through the biosynthesis of an environmentally friendly (green) compound and reduction of waste load entering the environment. Moreover, this work inferred spectrophotometry as an easy method to detect rhamnolipids in the biosurfactant products.

Evaluation of dermal wound healing and in vitro antioxidant efficiency of Bacillus subtilis SPB1 biosurfactant.

Science.gov (United States)

Zouari, Raida; Moalla-Rekik, Dorsaf; Sahnoun, Zouheir; Rebai, Tarek; Ellouze-Chaabouni, Semia; Ghribi-Aydi, Dhouha

2016-12-01

Lipopeptide microbial surfactants are endowed with unique surface properties as well as antimicrobial, anti-wrinkle, moisturizing and free radical scavenging activities. They were introduced safely in dermatological products, as long as they present low cytotoxicity against human cells. The present study was undertaken to evaluate the in vitro antioxidant activities and the wound healing potential of Bacillus subtilis SPB1 lipopeptide biosurfactant on excision wounds induced in experimental rats. The scavenging effect of Bacillus subtilis SPB1 biosurfactant on 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical at 1mg/mL was 70.4% (IC 50 =0.55mg/mL). The biosurfactant produced by Bacillus subtilis SPB1 also showed good reducing power and significant effects in terms of the β-carotene test (IC 50 =2.26mg/mL) when compared to BHA as a reference standard. Moreover, an interesting ferrous ion chelating activity (80.32%) was found for SPB1 biosurfactant at 1mg/mL. Furthermore, the topical application of Bacillus subtilis SPB1 biosurfactant based gel on the wound site in a rat model every two days, increased significantly the percentage of wound closure over a period of 13days, when compared to the untreated and CICAFLORA™-treated groups. Wound healing effect of SPB1 biosurfactant based gel was confirmed by histological study. Biopsies treated with SPB1 lipopeptides showed wholly re-epithelialized wound with a perfect epidermal regeneration. The present study provides justification for the use of Bacillus subtilis SPB1 lipopeptide biosurfactant based gel for the treatment of normal and complicated wounds as well as skin diseases. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Resazurin-based 96-well plate microdilution method for the determination of minimum inhibitory concentration of biosurfactants.

Science.gov (United States)

Elshikh, Mohamed; Ahmed, Syed; Funston, Scott; Dunlop, Paul; McGaw, Mark; Marchant, Roger; Banat, Ibrahim M

2016-06-01

To develop and validate a microdilution method for measuring the minimum inhibitory concentration (MIC) of biosurfactants. A standardized microdilution method including resazurin dye has been developed for measuring the MIC of biosurfactants and its validity was established through the replication of tetracycline and gentamicin MIC determination with standard bacterial strains. This new method allows the generation of accurate MIC measurements, whilst overcoming critical issues related to colour and solubility which may interfere with growth measurements for many types of biosurfactant extracts.

Optimizing Carbon/Nitrogen Ratio for Biosurfactant Production by a Bacillus subtilis Strain

Science.gov (United States)

Fonseca, R. R.; Silva, A. J. R.; de Franca, F. P.; Cardoso, V. L.; Sérvulo, E. F. C.

A Bacillus subtilis strain isolated from contaminated soil from a refinery has been screened for biosurfactant production in crystal sugar (sucrose) with different nitrogen sources (NaNO3' (NH4)2SO4' urea, and residual brewery yeast). The highest reduction in surface tension was achieved with a 48-h fermentation of crystal sugar and ammonium nitrate. Optimization of carbon/nitrogen ratio (3,9, and 15) and agitation rate (50, 150, and 250 rpm) for biosurfactant production was carried out using complete factorial design and response surface analysis. The condition of C/N 3 and 250 rpm allowed the maximum increase in surface activity of biosurfactant. A suitable model has been developed, having presented great accordance experimental data. Preliminary characterization of the bioproduct suggested it to be a lipopeptide with some isomers differing from those of a commercial surfactin.

Application of lipopeptide biosurfactant isolated from a halophile: Bacillus tequilensis CH for inhibition of biofilm.

Science.gov (United States)

Pradhan, Arun Kumar; Pradhan, Nilotpala; Mall, Gangotri; Panda, Himadri Tanaya; Sukla, Lala Behari; Panda, Prasanna Kumar; Mishra, Barada Kanta

2013-11-01

Biosurfactants are amphiphilic molecules having hydrophobic and hydrophilic moieties produced by various microorganisms. These molecules trigger the reduction of surface tension or interfacial tension in liquids. A biosurfactant-producing halophile was isolated from Lake Chilika, a brackish water lake of Odisha, India (19°41'39″N, 85°18'24″E). The halophile was identified as Bacillus tequilensis CH by biochemical tests and 16S rRNA gene sequencing and assigned accession no. KC851857 by GenBank. The biosurfactant produced by B. tequilensis CH was partially characterized as a lipopeptide using thin-layer chromatography, Fourier transform infrared spectroscopy, and nuclear magnetic resonance techniques. The minimum effective concentration of a biosurfactant for inhibition of pathogenic biofilm (Escherichia coli and Streptococcus mutans) on hydrophilic and hydrophobic surfaces was found to be 50 μg ml(-1). This finding has potential for a variety of applications.

Structural Characterization and Antimicrobial Activity of a Biosurfactant Obtained From Bacillus pumilus DSVP18 Grown on Potato Peels

Science.gov (United States)

Sharma, Deepak; Ansari, Mohammad Javed; Gupta, Sonam; Al Ghamdi, Ahmad; Pruthi, Parul; Pruthi, Vikas

2015-01-01

Background: Biosurfactants constitute a structurally diverse group of surface-active compounds derived from microorganisms. They are widely used industrially in various industrial applications such as pharmaceutical and environmental sectors. Major limiting factor in biosurfactant production is their production cost. Objectives: The aim of this study was to investigate biosurfactant production under laboratory conditions with potato peels as the sole source of carbon source. Materials and Methods: A biosurfactant-producing bacterial strain (Bacillus pumilus DSVP18, NCBI GenBank accession no. GQ865643) was isolated from motor oil contaminated soil samples. Biochemical characteristics of the purified biosurfactant were determined and its chemical structure was analyzed. Stability studies were performed and biological activity of the biosurfactant was also evaluated. Results: The strain, when grown on modified minimal salt media supplemented with 2% potato peels as the sole carbon source, showed the ability to reduce Surface Tension (ST) value of the medium from 72 to 28.7 mN/m. The isolated biosurfactant (3.2 ± 0.32 g/L) was stable over a wide range of temperatures (20 - 120 ºC), pH (2-12) and salt concentrations (2 - 12%). When characterized using high-performance liquid chromatography (HPLC) and Fourier transform infrared spectroscopy, it was found to be a lipopeptide in nature, which was further confirmed by Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (mass peak 1044.60) and nuclear magnetic resonance (NMR) studies. Data showed that the isolated biosurfactant at the concentration range of 30 - 35 µg/ml had strong antimicrobial activity when tested against standard strains of Bacillus cereus, Escherichia coli, Salmonella enteritidis, Staphylococcus aureus and Paenibacillus larvae. Conclusions: Potato peels were proved to be potentially useful substrates for biosurfactant production by B. pumilus DSVP18. The strain possessed a

Biophysical Effects of a Polymeric Biosurfactant in Candida krusei and Candida albicans Cells.

Science.gov (United States)

Ferreira, Gabriella Freitas; Dos Santos Pinto, Bruna Lorrana; Souza, Eliene Batista; Viana, José Lima; Zagmignan, Adrielle; Dos Santos, Julliana Ribeiro Alves; Santos, Áquila Rodrigues Costa; Tavares, Priscila Batista; Denadai, Ângelo Márcio Leite; Monteiro, Andrea Souza

2016-12-01

This study evaluated the effects of a polymeric biosurfactant produced by Trichosporon montevideense CLOA72 in the adhesion of Candida albicans and Candida krusei cells to human buccal epithelial cells and its interference in biofilm formation by these strains. The biofilm inhibition by biosurfactant (25 mg/mL) in C. krusei and C. albicans in polystyrene was reduced up to 79.5 and 85 %, respectively. In addition, the zeta potential and hydrodynamic diameter of the yeasts altered as a function of the biosurfactant concentration added to the cell suspension. The changes in the cell surface characteristics and the interface modification can contribute to the inhibition of the initial adherence of yeasts cells to the surface. In addition, the analyses of the biofilm matrix and planktonic cell surfaces demonstrated differences in carbohydrate and protein concentrations for the two studied strains, which may contribute to the modulation of cell adhesion or consolidation of biofilms, especially in C. krusei. This study suggests a possible application of the of CLOA72 biosurfactant in inhibiting the adhesion and formation of biofilms on biological surfaces by yeasts of the Candida genus.

The colloid hematite particle migration through the unsaturated porous bed at the presence of biosurfactants.

Science.gov (United States)

Pawlowska, Agnieszka; Sznajder, Izabela; Sadowski, Zygmunt

2017-07-01

Colloidal particles have an ability to sorb heavy metals, metalloids, and organic compounds (e.g. biosurfactants) present in soil and groundwater. The pH and ionic strength changes may promote release of such particles causing potential contaminant transport. Therefore, it is very important to know how a colloid particle-mineral particle and colloid-mineral-biosurfactant system behaves in the natural environment. They can have negative impact on the environment and human health. This study highlighted the influence of biosurfactants produced by Pseudomonas aeruginosa on the transport of colloidal hematite (α-Fe 2 O 3 ) through porous bed (materials collected from the Szklary and Zloty Stok solid waste heaps from Lower Silesia, Poland). Experiments were conducted using column set in two variants: colloid solution with porous bed and porous bed with adsorbed biosurfactants, in the ionic strengths of 5 × 10 -4 and 5 × 10 -3  M KCl. The zeta potential of mineral materials and colloidal hematite, before and after adsorption of biosurfactant, was determined. Obtained results showed that reduction in ionic strength facilitates colloidal hematite transport through the porous bed. The mobility of colloidal hematite was higher when the rhamnolipid adsorbed on the surface of mineral grain.

Effect of biosurfactant and fertilizer on biodegradation of crude oil by marine isolates of Bacillus megaterium, Corynebacterium kutscheri and Pseudomonas aeruginosa.

Science.gov (United States)

Thavasi, Rengathavasi; Jayalakshmi, Singaram; Banat, Ibrahim M

2011-01-01

This study was conducted to investigate the effects of fertilizers and biosurfactants on biodegradation of crude oil by three marine bacterial isolates; Bacillus megaterium, Corynebacterium kutscheri and Pseudomonas aeruginosa. Five sets of experiments were carried out in shake flask and microcosm conditions with crude oil as follows: Set 1-only bacterial cells added (no fertilizer and biosurfactant), Set 2-with additional fertilizer only, Set 3-with additional biosurfactant only, Set 4-with added biosurfactant+fertilizer, Set 5-with no bacterial cells added (control), all the above experimental sets were incubated for 168 h. The biosurfactant+fertilizer added Set 4, resulted in maximum crude oil degradation within shake flask and microcosm conditions. Among the three bacterial isolates, P. aeruginosa and biosurfactant produced by this strain resulted in maximum crude oil degradation compared to the other two bacterial strains investigated. Interestingly, when biosurfactant and bacterial cells were used (Set 3), significant oil biodegradation activity occurred and the difference between this treatment and that in Set 4 with added fertilizer+biosurfactant were only 4-5% higher degradation level in shake flask and 3.2-7% in microcosm experiments for all three bacterial strains used. It is concluded that, biosurfactants alone capable of promoting biodegradation to a large extent without added fertilizers, which will reduce the cost of bioremediation process and minimizes the dilution or wash away problems encountered when water soluble fertilizers used during bioremediation of aquatic environments. Copyright © 2010 Elsevier Ltd. All rights reserved.

Utilization of palm oil mill effluent as a novel and promising substrate for biosurfactant production by Nevskia ramosa NA3

Directory of Open Access Journals (Sweden)

Benjamas Cheirsilp

2013-04-01

Full Text Available This paper introduces palm oil mill effluent as a promising substrate for biosurfactant production. Potential strains ofbacteria were isolated from various hydrocarbon-contaminated soils and screened for biosurfactant production with the helpof the drop collapse method and surface tension measurements. Out of 26 isolates of bacteria, the strain NA3 showed thehighest bacterial growth with the highest surface tension reduction of 27.2 mN/m. It was then identified as Nevskia ramosaNA3 by biochemical and 16S rRNA sequence analysis. The Plackett-Burman experimental design was employed to determinethe important nutritional requirements for biosurfactant production by N. ramosa NA3 under controlled conditions. Six outof 11 factors of the production medium were found to significantly affect the production of biosurfactant. FeCl2 and NaNO3had a direct proportional correlation with the biosurfactant production. Commercial sugar, glucose, K2HPO4 and MgCl2showed inversely proportional relationship with biosurfactant production in the selected experimental range.

Biosurfactant-enhanced removal of phenanthrene from soil

NARCIS (Netherlands)

Noordman, WH; Ji, W; Brusseau, ML; Janssen, DB

1997-01-01

The possibility to use rhamnolipid biosurfactants for enhancing the elution of phenanthrene from a soil column was tested. Removal of 90% of the phenanthrene was achieved in a 3.6-fold shorter time period when the feed solution contained 500 mg/L rhamnolipid compared to treatment without

Lactobacillus acidophilus-derived biosurfactant effect on gtfB and gtfC expression level in Streptococcus mutans biofilm cells

Directory of Open Access Journals (Sweden)

Arezoo Tahmourespour

2011-03-01

Full Text Available Streptococcus mutans (S. mutans, harboring biofilm formation, considered as a main aetiological factor of dental caries. Gtf genes play an important role in S. mutans biofilm formation. The purpose of this study was to investigate the effect of Lactobacillus acidophilus-derived biosurfactant on S. mutans biofilm formation and gtfB/C expression level (S. mutans standard strain ATCC35668 and isolated S. mutans strain (22 from dental plaque. The Lactobacillus acidophilus (L. acidophilus DSM 20079 was selected as a probiotic strain to produce biosurfactant. The FTIR analysis of its biosurfactant showed that it appears to have a protein-like component. Due to the release of such biosurfactants, L. acidophilus was able to interfere in the adhesion and biofilm formation of the S. mutans to glass slide. It also could make streptococcal chains shorter. Using realtime RT-PCR quantitation method made it clear that gtfB and gtfC gene expression were decreased in the presence of L. acidophilus-derived biosurfactant fraction. Several properties of S. mutans cells (the surface properties, biofilm formation, adhesion ability and gene expression were changed after L. acidophilus-derived biosurfactant treatment. It is also concluded that biosurfacant treatment can provide an optional way to control biofilm development. On the basis of our findings, we can suggest that the prepared biosurfactant may interfere with adhesion processes of S. mutans to teeth surfaces, provided additional evaluation produce satisfactory results.

Production and properties of biosurfactants from a newly isolated Pseudomonas fluorescens HW-6 growing on hexandecane

Energy Technology Data Exchange (ETDEWEB)

Vasileva-Tonkova, E.; Galabova, D. [Bulgarian Academy of Sciences, Dept. of Microbial Biochemistry, Sofia (Bulgaria); Stoimenova, E.; Lalchev, Z. [Dept. of Biochemistry, Sofia Univ. ' ' St. Kliment Ohridski' ' , Sofia (Bulgaria)

2006-07-15

The newly isolated from industrial wastewater Pseudomonas fluorescens strain HW-6 produced glycolipid biosurfactants at high concentrations (1.4-2.0 g 1{sup -1}) when grown on hexadecane as a sole carbon source. Biosurfactants decreased the surface tension of the air/water interface by 35 mN m{sup -1} and possessed a low critical micelle concentration value of 20 mg 1{sup -1}, which indicated high surface activity. They efficiently emulsified aromatic hydrocarbons, kerosene, n-paraffins and mineral oils. Biosurfactant production contributed to a significant increase in cell hydrophobicity correlated with an increased growth of the strain on hexadecane. The results suggested that the newly isolated strain of Ps. fluorescens and produced glycolipid biosurfactants with effective surface and emulsifying properties are very promising and could find application for bioremediation of hydrocarbon-polluted sites. (orig.)

Microbial biosurfactants as additives for food industries.

Science.gov (United States)

Campos, Jenyffer Medeiros; Stamford, Tânia Lúcia Montenegro; Sarubbo, Leonie Asfora; de Luna, Juliana Moura; Rufino, Raquel Diniz; Banat, Ibrahim M

2013-01-01

Microbial biosurfactants with high ability to reduce surface and interfacial surface tension and conferring important properties such as emulsification, detergency, solubilization, lubrication and phase dispersion have a wide range of potential applications in many industries. Significant interest in these compounds has been demonstrated by environmental, bioremediation, oil, petroleum, food, beverage, cosmetic and pharmaceutical industries attracted by their low toxicity, biodegradability and sustainable production technologies. Despite having significant potentials associated with emulsion formation, stabilization, antiadhesive and antimicrobial activities, significantly less output and applications have been reported in food industry. This has been exacerbated by uneconomical or uncompetitive costing issues for their production when compared to plant or chemical counterparts. In this review, biosurfactants properties, present uses and potential future applications as food additives acting as thickening, emulsifying, dispersing or stabilising agents in addition to the use of sustainable economic processes utilising agro-industrial wastes as alternative substrates for their production are discussed. © 2013 American Institute of Chemical Engineers.

Genomic and functional features of the biosurfactant producing Bacillus sp. AM13.

Science.gov (United States)

Shaligram, Shraddha; Kumbhare, Shreyas V; Dhotre, Dhiraj P; Muddeshwar, Manohar G; Kapley, Atya; Joseph, Neetha; Purohit, Hemant P; Shouche, Yogesh S; Pawar, Shrikant P

2016-09-01

Genomic studies provide deeper insights into secondary metabolites produced by diverse bacterial communities, residing in various environmental niches. This study aims to understand the potential of a biosurfactant producing Bacillus sp. AM13, isolated from soil. An integrated approach of genomic and chemical analysis was employed to characterize the antibacterial lipopeptide produced by the strain AM13. Genome analysis revealed that strain AM13 harbors a nonribosomal peptide synthetase (NRPS) cluster; highly similar with known biosynthetic gene clusters from surfactin family: lichenysin (85 %) and surfactin (78 %). These findings were substantiated with supplementary experiments of oil displacement assay and surface tension measurements, confirming the biosurfactant production. Further investigation using LCMS approach exhibited similarity of the biomolecule with biosurfactants of the surfactin family. Our consolidated effort of functional genomics provided chemical as well as genetic leads for understanding the biochemical characteristics of the bioactive compound.

An efficient biosurfactant-producing bacterium Selenomonas ruminantium CT2, isolated from mangrove sediment in south of Thailand.

Science.gov (United States)

Saimmai, Atipan; Onlamool, Theerawat; Sobhon, Vorasan; Maneerat, Suppasil

2013-01-01

Biosurfactant-producing bacteria, isolate CT2, was isolated from mangrove sediment in the south of Thailand. The sequence of the 16S rRNA gene from isolate CT2 showed 100 % similarity with Selenomonas ruminantium. The highest biosurfactant production (5.02 g/l) was obtained when the cells were grown on minimal salt medium containing 15 g/l molasses and 1 g/l commercial monosodium glutamate supplemented with 1 g/l NaCl, 0.1 g/l leucine, 5 % (v/v) inoculum size at 30 °C and 150 rpm after 54 h of cultivation. The biosurfactant obtained by extraction with ethyl acetate showed high surface tension reduction (25.5 mN/m), a small CMC value (8 mg/l), thermal and pH stability with respect to surface tension reduction and emulsification activity and a high level of salt tolerance. The biosurfactant obtained was confirmed as a lipopeptide by using a biochemical test, FT-IR, MNR and mass spectrometry. The crude biosurfactant showed a broad spectrum of antimicrobial activity and also had the ability to emulsify oil and enhance PAHs solubility.

The influence of biosurfactant adsorption on the physicochemical behaviour of carbon steel surfaces using contact angle measurements and X-ray photoelectron spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Shubina, V., E-mail: varvara.shubina2014@gmail.com [LUNAM Université, IFSTTAR, MAST, SMC, F-44340 Bouguenais (France); Gaillet, L. [LUNAM Université, IFSTTAR, MAST, SMC, F-44340 Bouguenais (France); Ababou-Girard, S. [Institut de Physique de Rennes, Département Matériaux et Nanosciences, UMR 6251 CNRS, Université Rennes 1, 35000 Rennes-Cedex (France); Gaudefroy, V. [LUNAM Université, IFSTTAR, MAST, SMC, F-44340 Bouguenais (France); Chaussadent, T.; Farças, F. [Université Paris-Est, IFSTTAR, MAST, CPDM, F-77447 Marne-la-Vallée (France); Meylheuc, T. [INRA, UMR1319 Micalis, F-78352 Jouy-en-Josas (France); AgroParisTech, UMR Micalis, F-78352 Jouy-en-Josas (France); Dagbert, C. [2 Chemin de la Grand’côte, 36270 Éguzon-Chantôme (France); Creus, J. [LaSIE, UMR7356, Université de La Rochelle, Pôle Sciences et Technologie, Bâtiment Marie Curie, Avenue Michel Crépeau, 17000 La Rochelle (France)

2015-10-01

Highlights: • Surface modifications to carbon steel surfaces due to the adsorption of a biosurfactant derived from Pseudomonas fluorescens bacteria cells were investigated using contact angle measurements (CAM) and X-ray photoelectron spectroscopy (XPS). • CAM allowed to establish an increase of electron-donating properties of steel surface due to the biosurfactant adsorption. • XPS demonstrated that biosurfactant molecules change the stoichiometry of mixted-oxide layer and the new outer layer mostly composed of magnetite. • Thickness and density of adsorbed biosurfactants layers were highlighted using a semiquantitative approach for 3 different concentrations of biomolecules. - Abstract: We investigated modifications to carbon steel surfaces due to the adsorption of a biosurfactant derived from Pseudomonas fluorescens bacteria cells using contact angle measurements (CAM) and X-ray photoelectron spectroscopy (XPS). After conditioning carbon steel in solutions with three different concentrations of biosurfactant molecules: 0.05, 0.3 and 1 g L{sup −1}, the average thickness of the biosurfactant layer on the carbon steel specimens was 7.9 ± 0.3, 12.1 ± 0.5 and 16.4 ± 0.7 Å, respectively. The biosurfactants changed the composition of both the Fe{sup 2+} and Fe{sup 3+} mixed-oxide layer and the outer layer, mostly composed of Fe{sup 3+} associated with magnetite. Contact angle measurements indicate decreased hydrophobic properties after the carbon steel was modified by biosurfactant. It was shown that the carbon steel surface free energy depends on the biosurfactant concentration, due to an acquisition of strong electron-donating properties.

The influence of biosurfactant adsorption on the physicochemical behaviour of carbon steel surfaces using contact angle measurements and X-ray photoelectron spectroscopy

International Nuclear Information System (INIS)

Shubina, V.; Gaillet, L.; Ababou-Girard, S.; Gaudefroy, V.; Chaussadent, T.; Farças, F.; Meylheuc, T.; Dagbert, C.; Creus, J.

2015-01-01

Highlights: • Surface modifications to carbon steel surfaces due to the adsorption of a biosurfactant derived from Pseudomonas fluorescens bacteria cells were investigated using contact angle measurements (CAM) and X-ray photoelectron spectroscopy (XPS). • CAM allowed to establish an increase of electron-donating properties of steel surface due to the biosurfactant adsorption. • XPS demonstrated that biosurfactant molecules change the stoichiometry of mixted-oxide layer and the new outer layer mostly composed of magnetite. • Thickness and density of adsorbed biosurfactants layers were highlighted using a semiquantitative approach for 3 different concentrations of biomolecules. - Abstract: We investigated modifications to carbon steel surfaces due to the adsorption of a biosurfactant derived from Pseudomonas fluorescens bacteria cells using contact angle measurements (CAM) and X-ray photoelectron spectroscopy (XPS). After conditioning carbon steel in solutions with three different concentrations of biosurfactant molecules: 0.05, 0.3 and 1 g L −1 , the average thickness of the biosurfactant layer on the carbon steel specimens was 7.9 ± 0.3, 12.1 ± 0.5 and 16.4 ± 0.7 Å, respectively. The biosurfactants changed the composition of both the Fe 2+ and Fe 3+ mixed-oxide layer and the outer layer, mostly composed of Fe 3+ associated with magnetite. Contact angle measurements indicate decreased hydrophobic properties after the carbon steel was modified by biosurfactant. It was shown that the carbon steel surface free energy depends on the biosurfactant concentration, due to an acquisition of strong electron-donating properties

Aqueous phase partitioning of hexachlorocyclohexane (HCH) isomers by biosurfactant produced by Pseudomonas aeruginosa WH-2

International Nuclear Information System (INIS)

Sharma, Suman; Singh, Partapbir; Raj, Mayil; Chadha, Bhupinder Singh; Saini, Harvinder Singh

2009-01-01

The different isomers of technical-grade hexachlorocyclohexane (t-HCH) including the insecticidal γ-isomer, commonly known as lindane, have been reported to be toxic, carcinogenic and endocrine disrupters. The spatial arrangements of the chlorine atoms on different isomers and low aqueous phase solubility contribute to their persistence in environment, β-HCH being the most resistance to transformation. The biosurfactant preparation of Pseudomonas aeruginosa isolate WH-2 was evaluated for its ability to improve the aqueous phase partitioning of different isomers of HCH-muck. Further, the ability of biosurfactant preparation to emulsify HCH and n-hexadecane was checked under different conditions, usually characteristic of sites contaminated with pollutants viz. wide range of pH, temperature, and salinity. The data obtained from this study will be helpful in designing suitable bioremediation strategies for huge stock piles of HCH-muck and sites polluted by reckless use/disposal of HCH-isomers.

Biosurfactant production by Pseudomonas aeruginosa MSIC02 in cashew apple juice using a 24 full factorial experimental design

Directory of Open Access Journals (Sweden)

Rocha Maria Valderez Ponte

2014-01-01

Full Text Available In this work, the production of biosurfactants from cashew apple juice by P. aeruginosa MSIC02 was investigate by carrying out a 24 full factorial experimental design, using temperature, glucose concentration from cashew apple juice, phosphorous concentration and cultivation time as variables. The response variable was the percentage of reduction in surface tension in the cell-free culture medium, since it indicates the surface-active agent production. Maximum biosurfactant production, equivalent to a 58% reduction in surface tension, was obtained at 37°C, with glucose concentration of 5.0 g/L and no phosphorous supplementation. Surface tension reduction was significant, since low values were observed in the cell-free medium (27.50 dyne/cm, indicating that biosurfactant was produced. The biosurfactant emulsified different hydrophobic sources and showed stability in the face of salinity, exposure to high temperatures and extreme pH conditions. These physiochemical properties demonstrate the potential for using biosurfactants produced by P. aeruginosa MSIC02 in various applications.

Coal induced production of a rhamnolipid biosurfactant by Pseudomonas stutzeri, isolated from the formation water of Jharia coalbed.

Science.gov (United States)

Singh, Durgesh Narain; Tripathi, Anil Kumar

2013-01-01

A strain of Pseudomonas stutzeri was isolated form an enrichment of perchlorate reducing bacteria from the formation water collected from an Indian coalbed which solubilized coal and produced copious amount of biosurfactant when coal was added to the medium. It produced maximum biosurfactant with lignite coal followed by olive oil and soybean oil which was able to emulsify several aromatic hydrocarbons including kerosene oil, diesel oil, hexane, toluene etc. Haemolytic test, growth inhibition of Bacillus subtilis and FTIR analysis showed rhamnolipid nature of the biosurfactant. The stability of the coal induced biosurfactant in pH range of 4-8 and up to 25% NaCl concentration and 100 °C temperature suggests that due to its ability to produce biosurfactant and solubilize coal P. stutzeri may be useful in the coalbed for in situ biotransformation of coal into methane and in the bioremediation of PAHs from oil contaminated sites including marine environments. Copyright © 2012 Elsevier Ltd. All rights reserved.

Biosurfactant production by hydrocarbon-degrading Brevibacterium and Vibrio isolates from the sea pen Pteroeides spinosum (Ellis, 1764).

Science.gov (United States)

Graziano, Marco; Rizzo, Carmen; Michaud, Luigi; Porporato, Erika Maria Diletta; De Domenico, Emilio; Spanò, Nunziacarla; Lo Giudice, Angelina

2016-09-01

Among filter-feeders, pennatulids are the most complex and polymorphic members of the cnidarian class Anthozoa. They display a wide distribution throughout all the oceans, constituting a significant component of the sessile megafauna from intertidal to abyssal depths. In this study, a total of 118 bacterial isolates from enrichment cultures, carried out with homogenates of the sea pen Pteroeides spinosum (Ellis, 1764), were screened for hydrocarbon utilization by using the 2,6-dichlorophenol indophenol assay. Among them, 83 hydrocarbon-oxidizing isolates were analyzed for biosurfactant production by standard screening tests (i.e., emulsifying activity, E24 detection, surface tension measurement, microplate assay). The 16S rRNA gene sequencing revealed the affiliation of the most promising isolates to the genera Brevibacterium and Vibrio. Biosurfactant production resulted strongly affected by salinity and temperature conditions, and occurred in the presence of diesel oil and/or crude oil, whereas no production was observed when isolates were grown on tetradecane. The strains resulted able to create stable emulsions, thus suggesting the production of biosurfactants. Further analyses revealed a glycolipidic nature of the biosurfactant extracted from Vibrio sp. PBN295, a genus that has been only recently reported as biosurfactant producer. Results suggest that pennatulids could represent a novel source for the isolation of hydrocarbon-oxidizing bacteria with potential in biosurfactant production. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Assessment of synergistic antibacterial activity of combined biosurfactants revealed by bacterial cell envelop damage.

Science.gov (United States)

Sana, Santanu; Datta, Sriparna; Biswas, Dipa; Sengupta, Dipanjan

2018-02-01

Besides potential surface activity and some beneficial physical properties, biosurfactants express antibacterial activity. Bacterial cell membrane disrupting ability of rhamnolipid produced by Pseudomonas aeruginosa C2 and a lipopeptide type biosurfactant, BS15 produced by Bacillus stratosphericus A15 was examined against Staphylococcus aureus ATCC 25923 and Escherichia coli K8813. Broth dilution technique was followed to examine minimum inhibitory concentration (MIC) of both the biosurfactants. The combined effect of rhamnolipid and BS15 against S. aureus and E. coli showed synergistic activity by expressing fractional inhibitory concentration (FIC) index of 0.43 and 0.5. Survival curve of both the bacteria showed bactericidal activity after treating with biosurfactants at their MIC obtained from FIC index study as it killed >90% of initial population. The lesser value of MIC than minimum bactericidal concentration (MBC) of the biosurfactants also supported their bactericidal activity against both the bacteria. Membrane permeability against both the bacteria was supported by amplifying protein release, increasing of cell surface hydrophobicity, withholding capacity of crystal violet dye and leakage of intracellular materials. Finally cell membrane disruption was confirmed by scanning electron microscopy (SEM). All these experiments expressed synergism and effective bactericidal activity of the combination of rhamnolipid and BS15 by enhancing the bacterial cell membrane permeability. Such effect of the combination of rhamnolipid and BS15 could make them promising alternatives to traditional antibiotic in near future. Copyright © 2017 Elsevier B.V. All rights reserved.

Degradation of Polycyclic Aromatic Hydrocarbon Pyrene by Biosurfactant-Producing Bacteria Gordonia cholesterolivorans AMP 10

Directory of Open Access Journals (Sweden)

Tri Handayani Kurniati

2016-12-01

Full Text Available Pyrene degradation and biosurfactant activity by a new strain identified as Gordonia cholesterolivorans AMP 10 were studied. The strain grew well and produced effective biosurfactants in the presence of glucose, sucrose, and crude oil. The biosurfactants production was detected by the decreased surface tension of the medium and emulsification activity.  Analysis of microbial growth parameters showed that AMP10 grew best at 50 µg mL-1 pyrene concentration, leading to 96 % degradation of pyrene within 7 days. The result of nested PCR analysis revealed that this isolate possessed the nahAc gene which encodes dioxygenase enzyme for initial degradation of Polycyclic Aromatic Hydrocarbon (PAH. Observation of both tensio-active and emulsifying activities indicated that biosurfactants which produced by AMP 10 when grown on glucose could lower the surface tension of medium from 71.3 mN/m to 24.7 mN/m and formed a stable emulsion in used lubricant oil with an emulsification index (E24 of 74%. According to the results, it is suggested that the bacterial isolates G. cholesterolivorans AMP10 are suitable candidates for bioremediation of PAH-contaminated environments.How to CiteKurniati, T. H.,  Rusmana, I. Suryani, A. & Mubarik, N. R. (2016. Degradation of Polycyclic Aromatic Hydrocarbon Pyrene by Biosurfactant-Producing Bacteria Gordonia cholesterolivorans AMP 10. Biosaintifika: Journal of Biology & Biology Education, 8(3, 336-343. 

Biosurfactants in Dwarf Mistletoe ( Arceuthobium ) | Vaudry | Plant ...

African Journals Online (AJOL)

0.01), reflects a drop in water surface tension from 72 mN/m to under 30 mN/m, a purification factor of 575-fold, and a significantly more active (p<0.05) purified sample relative to the crude. The biosurfactant has a critical micellar concentration ...

Improvement of methyl orange dye biotreatment by a novel isolated strain, Aeromonas veronii GRI, by SPB1 biosurfactant addition.

Science.gov (United States)

Mnif, Inès; Maktouf, Sameh; Fendri, Raouia; Kriaa, Mouna; Ellouze, Semia; Ghribi, Dhouha

2016-01-01

Aeromonas veronii GRI (KF964486), isolated from acclimated textile effluent after selective enrichment on azo dye, was assessed for methyl orange biodegradation potency. Results suggested the potential of this bacterium for use in effective treatment of azo-dye-contaminated wastewaters under static conditions at neutral and alkaline pH value, characteristic of typical textile effluents. The strain could tolerate higher doses of dyes as it was able to decolorize up to 1000 mg/l. When used as microbial surfactant to enhance methyl orange biodecolorization, Bacillus subtilis SPB1-derived lipopeptide accelerated the decolorization rate and maximized slightly the decolorization efficiency at an optimal concentration of about 0.025%. In order to enhance the process efficiency, a Taguchi design was conducted. Phytotoxicity bioassay using sesame and radish seeds were carried out to assess the biotreatment effectiveness. The bacterium was able to effectively decolorize the azo dye when inoculated with an initial optical density of about 0.5 with 0.25% sucrose, 0.125% yeast extract, 0.01% SPB1 biosurfactant, and when conducting an agitation phase of about 24 h after static incubation. Germination potency showed an increase toward the nonoptimized conditions indicating an improvement of the biotreatment. When comparing with synthetic surfactants, a drastic decrease and an inhibition of orange methyl decolorization were observed in the presence of CTAB and SDS. The nonionic surfactant Tween 80 had a positive effect on methyl orange biodecolorization. Also, studies ensured that methyl orange removal by this strain could be due to endocellular enzymatic activities. To conclude, the addition of SPB1 bioemulsifier reduced energy costs by reducing effective decolorization period, biosurfactant stimulated bacterial decolorization method may provide highly efficient, inexpensive, and time-saving procedure in treatment of textile effluents.

Biological and physicochemical properties of biosurfactants produced by Lactobacillus jensenii P6A and Lactobacillus gasseri P65.

Science.gov (United States)

Morais, I M C; Cordeiro, A L; Teixeira, G S; Domingues, V S; Nardi, R M D; Monteiro, A S; Alves, R J; Siqueira, E P; Santos, V L

2017-09-19

Lactobacillus species produce biosurfactants that can contribute to the bacteria's ability to prevent microbial infections associated with urogenital and gastrointestinal tracts and the skin. Here, we described the biological and physicochemical properties of biosurfactants produced by Lactobacillus jensenii P 6A and Lactobacillus gasseri P 65 . The biosurfactants produced by L. jensenii P 6A and L. gasseri P 65 reduced the water surface tension from 72 to 43.2 mN m -1 and 42.5 mN m -1 as their concentration increased up to the critical micelle concentration (CMC) values of 7.1 and 8.58 mg mL -1 , respectively. Maximum emulsifying activity was obtained at concentrations of 1 and 5 mg mL -1 for the P 6A and P 65 strains, respectively. The Fourier transform infrared spectroscopy data revealed that the biomolecules consist of a mixture of carbohydrates, lipids and proteins. The gas chromatography-mass spectrum analysis of L. jensenii P 6A biosurfactant showed a major peak for 14-methypentadecanoic acid, which was the main fatty acid present in the biomolecule; conversely, eicosanoic acid dominated the biosurfactant produced by L. gasseri P 65 . Although both biosurfactants contain different percentages of the sugars galactose, glucose and ribose; rhamnose was only detected in the biomolecule produced by L. jensenii P 6A . Emulsifying activities were stable after a 60-min incubation at 100 °C, at pH 2-10, and after the addition of potassium chloride and sodium bicarbonate, but not in the presence of sodium chloride. The biomolecules showed antimicrobial activity against clinical isolates of Escherichia coli and Candida albicans, with MIC values of 16 µg mL -1 , and against Staphylococcus saprophyticus, Enterobacter aerogenes and Klebsiella pneumoniae at 128 µg mL -1 . The biosurfactants also disrupted preformed biofilms of microorganisms at varying concentrations, being more efficient against E. aerogenes (64%) (P 6A biosurfactant), and E. coli (46

Polycyclic aromatic hydrocarbon degradation by biosurfactant-producing Pseudomonas sp. IR1

Energy Technology Data Exchange (ETDEWEB)

Kumar, M. [Unidad de Biotecnologia del Petroleo, Centro de Biotecnologia, Fundacion Inst. de Estudios Avanzados (IDEA), Caracas (Venezuela); Synthesis and Biotics Div., Indian Oil Corp., Research and Development Center, Haryana (India); Leon, V.; Materano, A.D.S.; Ilzins, O.A.; Galindo-Castro, I.; Fuenmayor, S.L. [Unidad de Biotecnologia del Petroleo, Centro de Biotecnologia, Fundacion Inst. de Estudios Avanzados (IDEA), Caracas (Venezuela)

2006-03-15

We characterized a newly isolated bacterium, designated as IR1, with respect to its ability to degrade polycyclic aromatic hydrocarbons (PAHs) and to produce biosurfactants. Isolated IR1 was identified as Pseudomonas putida by analysis of 16S rRNA sequences (99.6% homology). It was capable of utilizing two-, three- and four-ring PAHs but not hexadecane and octadecane as a sole carbon and energy source. PCR and DNA hybridization studies showed that enzymes involved in PAH metabolism were related to the naphthalene dioxygenase pathway. Observation of both tensio-active and emulsifying activities indicated that biosurfactants were produced by IR1 during growth on both water miscible and immiscible substrates. The biosurfactants lowered the surface tension of medium from 54.9 dN cm{sup -1} to 35.4 dN cm{sup -1} and formed a stable and compact emulsion with an emulsifying activity of 74% with diesel oil, when grown on dextrose. These findings indicate that this isolate may be useful for bioremediation of sites contaminated with aromatic hydrocarbons. (orig.)

Evidence for a role of biosurfactants produced by Pseudomonas fluorescens in the spoilage of fresh aerobically stored chicken meat.

Science.gov (United States)

Mellor, Glen E; Bentley, Jessica A; Dykes, Gary A

2011-08-01

Fresh chicken meat is a fat-rich environment and we therefore hypothesised that production of biosurfactants to increase bioavailability of fats may represent one way in which spoilage bacteria might enhance the availability of nutrients. Numbers of Pseudomonas were determined on a total of 20 fresh and 20 spoiled chicken thighs with skin. A total of 400 randomly isolated Pseudomonas colonies from fresh (200) and spoiled (200) chicken were screened for the presence of biosurfactant production. Biosurfactant producing strains represented 5% and 72% of the Pseudomonas spp. isolates from fresh (mean count 2.3 log(10) cfu g(-1)) and spoiled (mean count 7.4 log(10) cfu g(-1)) chicken skin, respectively. Partially-purified biosurfactants derived from a subgroup of four Pseudomonasfluorescens strains obtained through the screening process were subsequently used to investigate the role that the addition of these compounds plays in the spoilage of aerobically stored chicken. Emulsification potential of the four selected biosurfactants was measured against a range of hydrocarbons and oils. All four biosurfactants displayed a greater ability to emulsify rendered chicken fat than hydrocarbons (paraffin liquid, toluene and hexane) and oils (canola, olive, sunflower and vegetable). Storage trials (4 °C) of chicken meat treated with the four selected biosurfactants revealed a significantly greater (P increase in total aerobic count (1.3-1.7 log(10) cfu g(-1)) occurred following one day of incubation. These results indicate that biosurfactants produced by Pseudomonas spp. may play an important role in the spoilage of aerobically stored chicken meat by making nutrients more freely available and providing strains producing them with a competitive advantage. Copyright © 2011 Elsevier Ltd. All rights reserved.

Isolation and functional characterization of a biosurfactant produced by a new and promising strain of Oleomonas sagaranensis AT18.

Science.gov (United States)

Saimmai, Atipan; Rukadee, Onkamon; Onlamool, Theerawat; Sobhon, Vorasan; Maneerat, Suppasil

2012-10-01

Biosurfactant-producing bacteria were isolated from mangrove sediment in southern Thailand. Isolates were screened for biosurfactant production by using the surface tension test. The highest reduction of surface tension was achieved with a bacterial strain which was identified by 16S rRNA gene sequencing as Oleomonas sagaranensis AT18. It has also been investigated using different carbon and nitrogen sources. It showed that the strain was able to grow and reduce the surface tension of the culture supernatant to 25 mN/m. In all 5.30 g of biosurfactant yield was obtained after 54 h of cultivation by using molasses and NaNO₃ as carbon and nitrogen sources, respectively. The biosurfactant recovery by chloroform:methanol extraction showed a small critical micelle concentration value (8 mg/l), thermal and pH stability with respect to surface tension reduction. It also showed emulsification activity and a high level of salt concentration. The biosurfactant obtained was confirmed as a glycolipid by using a biochemical test, FT-IR and mass spectra. The crude biosurfactant showed a broad spectrum of antimicrobial activity and also had the ability to emulsify oil and enhance PAHs solubility.

Production of biosurfactant from Bacillus licheniformis for microbial enhanced oil recovery and inhibition the growth of sulfate reducing bacteria

Directory of Open Access Journals (Sweden)

H.S. El-Sheshtawy

2015-06-01

Full Text Available In this study, the bacterium Bacillus licheniformis has been isolated from oil reservoir; the ability of this bacterium to produce a biosurfactant was detected. Surface properties of the produced biosurfactant were confirmed by determining the emulsification power as well as surface and interfacial tension. The crude biosurfactant has been extracted from supernatant culture growth, and the yield of crude biosurfactant was about 1 g/l. Also, chemical structure of the produced biosurfactant was confirmed using FTIR analysis. Results revealed that, the emulsification power has been increased up to 96% and the surface tension decreased from 72 of distilled water to 36 mN/m after 72 h of incubation. The potential application of this bacterial species in microbial-enhanced oil recovery (MEOR was investigated. The percent of oil recovery was 16.6% upon application in a sand pack column designed to stimulate an oil recovery. It also showed antimicrobial activity against the growth of different strains of SRB (sulfate reducing bacteria. Results revealed that a complete inhibition of SRB growth using 1.0% crude biosurfactant is achieved after 3 h.

SCREENING OF BIOSURFACTANT PRODUCTION BY BACILLUS SP ISOLATED FROM COASTAL REGION IN CUDDALORE TAMILNADU

OpenAIRE

Bhuvaneswari. M*and P. Sivagurunathan

2016-01-01

Marine microorganisms produce extracellular or membrane associated surface-active compounds (bio surfactants). Biosurfactant are organic compounds belonging to various classes including glycolipids, lipopeptides, fatty acids, phospholipids that reduce the interfacial tension between immiscible liquids.This study deals with production and characterization of biosurfactant from Bacillus sp. The efficiency of Bacillus spstrain isolated from a marine sediments soil sample from coastal region -Cud...

Utilization of sophorolipids as biosurfactants for postemergence herbicides

Science.gov (United States)

Sophorolipids are carbohydrate-based, amphiphilic biosurfactants produced by several species of the Starmerella yeast clade. Most sophorolipids are partially acetylated sophorose sugars O-ß-glycosidically linked to 17-L-hydroxy-delta9-octadecenoic acid, where typically the acyl carboxyl group forms...

Production of a new glycolipid biosurfactant from marine Nocardiopsis lucentensis MSA04 in solid-state cultivation.

Science.gov (United States)

Kiran, G Seghal; Thomas, T Anto; Selvin, Joseph

2010-06-15

Considering the need of potential biosurfactant producers and economic production processes using industrial waste, the present study aims to develop solid-state culture (SSC) of a marine actinobacterium for biosurfactant production. A potential biosurfactant producer Nocardiopsis lucentensis MSA04 was isolated from the marine sponge Dendrilla nigra. Among the substrates screened, wheat bran increased the production significantly (E(24) 25%) followed by oil seed cake and industrial waste such as tannery pretreated sludge, treated molasses (distillery waste) and pretreated molasses. Enhanced biosurfactant production was achieved under SSC conditions using kerosene as carbon source, beef extract as nitrogen source and wheat bran as substrate. The maximum production of biosurfactant by MSA04 occurred at a C/N ratio of 0.5 envisaging that a higher amount of nitrogen source is required by the strain compared to that of the carbon source. The kerosene and beef extract interactively increase the production and a stable production was attained with the influence of both factors independently. A significant interactive influence of secondary control factors such as copper sulfate and inoculum size was validated in response surface methods-based experiments. The surface active compound produced by MSA04 was characterized as glycolipid with a hydrophobic non-polar hydrocarbon chain (nonanoic acid methyl ester) and hydrophilic sugar, 3-acetyl 2,5 dimethyl furan. In conclusion, the strain N. lucentensis MSA04 was a potential source of glycolipid biosurfactant, could be used for the development of bioremediation processes in the marine environment. Copyright 2010 Elsevier B.V. All rights reserved.

Halomonas sp. BS4, A biosurfactant producing halophilic bacterium isolated from solar salt works in India and their biomedical importance.

Science.gov (United States)

Donio, Mariathason Birdilla Selva; Ronica, Fernando Arul; Viji, Vijayaragavan Thanga; Velmurugan, Subramanian; Jenifer, John Selesteen Charles Adlin; Michaelbabu, Mariavincent; Dhar, Prasenjit; Citarasu, Thavasimuthu

2013-12-01

Halophilic bacteria were isolated from Thamaraikulam solar salt works in India. After routine biosurfactant screening by various methods, the biosurfactant producing bacteria, Halomonas sp BS4 was confirmed by 16 S rRNA sequencing. The growth optimization of Halomonas sp BS4 revealed their optimum growth at 8% NaCl and 6-8 pH in the growth medium. Further the partially purified biosurfactants were characterized by TLC, FTIR and GC-MS analysis. GC-MS results revealed that, the partial purified biosurfactants contain 1, 2-Ethanediamine N, N, N', N'-tetra, 8-Methyl-6-nonenamide, (Z)-9-octadecenamide and a fatty acid derivative. Pharmacological screening of antibacterial, antifungal, antiviral and anticancer assays revealed that, the biosurfactant extracted from Halomonas sp BS4 effectively controlled the human pathogenic bacteria and fungi an aquaculturally important virus, WSSV. The biosurfactant also suppressed the proliferation of mammary epithelial carcinoma cell by 46.77% at 2.5 μg concentration. Based on these findings, the present study concluded that, there is a possibility to develop eco-friendly antimicrobial and anticancer drugs from the extremophilic origin.

Simultaneous Production of Biosurfactants and Bacteriocins by Probiotic Lactobacillus casei MRTL3

Science.gov (United States)

Sharma, Deepansh; Singh Saharan, Baljeet

2014-01-01

Lactic acid bacteria (LAB) are ubiquitous and well-known commensal bacteria in the human and animal microflora. LAB are extensively studied and used in a variety of industrial and food fermentations. They are widely used for humans and animals as adjuvants, probiotic formulation, and dietary supplements and in other food fermentation applications. In the present investigation, LAB were isolated from raw milk samples collected from local dairy farms of Haryana, India. Further, the isolates were screened for simultaneous production of biosurfactants and bacteriocins. Biosurfactant produced was found to be a mixture of lipid and sugar similar to glycolipids. The bacteriocin obtained was found to be heat stable (5 min at 100°C). Further, DNA of the strain was extracted and amplified by the 16S rRNA sequencing using universal primers. The isolate Lactobacillus casei MRTL3 was found to be a potent biosurfactant and bacteriocin producer. It seems to have huge potential for food industry as a biopreservative and/or food ingredient. PMID:24669225

Improved ADM1 model for anaerobic digestion process considering physico-chemical reactions.

Science.gov (United States)

Zhang, Yang; Piccard, Sarah; Zhou, Wen

2015-11-01

The "Anaerobic Digestion Model No. 1" (ADM1) was modified in the study by improving the bio-chemical framework and integrating a more detailed physico-chemical framework. Inorganic carbon and nitrogen balance terms were introduced to resolve the discrepancies in the original bio-chemical framework between the carbon and nitrogen contents in the degraders and substrates. More inorganic components and solids precipitation processes were included in the physico-chemical framework of ADM1. The modified ADM1 was validated with the experimental data and used to investigate the effects of calcium ions, magnesium ions, inorganic phosphorus and inorganic nitrogen on anaerobic digestion in batch reactor. It was found that the entire anaerobic digestion process might exist an optimal initial concentration of inorganic nitrogen for methane gas production in the presence of calcium ions, magnesium ions and inorganic phosphorus. Copyright © 2015 Elsevier Ltd. All rights reserved.

Inhibition of initial adhesion of uropathogenic Enterococcus faecalis by biosurfactants from Lactobacillus isolates.

OpenAIRE

Velraeds, M M; van der Mei, H C; Reid, G; Busscher, H J

1996-01-01

In this study, 15 Lactobacillus isolates were found to produce biosurfactants in the mid-exponential and stationary growth phases. The stationary-phase biosurfactants from lactobacillus casei subsp. rhamnosus 36 and ATCC 7469, Lactobacillus fermentum B54, and Lactobacillus acidophilus RC14 were investigated further to determine their capacity to inhibit the initial adhesion of uropathogenic Enterococcus faecalis 1131 to glass in a parallel-plate flow chamber. The initial deposition rate of E....

Combined effects of DOM extracted from site soil/compost and biosurfactant on the sorption and desorption of PAHs in a soil-water system

Energy Technology Data Exchange (ETDEWEB)

Yu Hui, E-mail: yuhui200@uregina.ca [Environmental Systems Engineering Program, Faculty of Engineering and Applied Science, University of Regina, Regina, SK S4S 0A2 (Canada); Huang Guohe, E-mail: gordon.huang@uregina.ca [Environmental Systems Engineering Program, Faculty of Engineering and Applied Science, University of Regina, Regina, SK S4S 0A2 (Canada); An Chunjiang, E-mail: an209@uregina.ca [Environmental Systems Engineering Program, Faculty of Engineering and Applied Science, University of Regina, Regina, SK S4S 0A2 (Canada); Wei Jia, E-mail: jia.wei@iseis.org [Environmental Systems Engineering Program, Faculty of Engineering and Applied Science, University of Regina, Regina, SK S4S 0A2 (Canada)

2011-06-15

Highlights: {yields} The combined DOM and biosurfactant significantly enhanced desorption of PAHs. {yields} Compost DOM exhibited higher desorption enhancement capacity than the soil DOM. {yields} Competition among PAHs, DOM and biosurfactant for sorption site determined desorption of PAHs from soil. {yields} Formation of DOM-biosurfactant complex enhance desorption extent of PAHs. - Abstract: The combined effects of DOM and biosurfactant on the sorption/desorption behavior of phenanthrene (PHE) and pyrene (PYR) in soil water systems were systematically investigated. Two origins of DOMs (extracted from soil and extracted from food waste compost) and an anionic biosurfactant (rhamnolipid) were introduced. The presence of DOM in the aqueous phase could decrease the sorption of PAHs, thus influence their mobility. Desorption enhancement for both PHE and PYR in the system with compost DOM was greater than that in the soil DOM system. This is due to the differences in specific molecular structures and functional groups of two DOMs. With the co-existence of biosurfactant and DOM, partitioning is the predominant process and the desorption extent was much higher than the system with DOM or biosurfactant individually. For PHE, the desorption enhancement of combined DOM and biosurfactant was larger than the sum of DOM or biosurfactant; however desorption enhancement for PYR in the combined system was less than the additive enhancement in two individual system under low PAH concentration. This could be explained as the competition sorption among PAHs, DOM and biosurfactant. The results of this study will help to clarify the transport of petroleum pollutants in the remediation of HOCs-contaminated soils.

Combined effects of DOM extracted from site soil/compost and biosurfactant on the sorption and desorption of PAHs in a soil-water system

International Nuclear Information System (INIS)

Yu Hui; Huang Guohe; An Chunjiang; Wei Jia

2011-01-01

Highlights: → The combined DOM and biosurfactant significantly enhanced desorption of PAHs. → Compost DOM exhibited higher desorption enhancement capacity than the soil DOM. → Competition among PAHs, DOM and biosurfactant for sorption site determined desorption of PAHs from soil. → Formation of DOM-biosurfactant complex enhance desorption extent of PAHs. - Abstract: The combined effects of DOM and biosurfactant on the sorption/desorption behavior of phenanthrene (PHE) and pyrene (PYR) in soil water systems were systematically investigated. Two origins of DOMs (extracted from soil and extracted from food waste compost) and an anionic biosurfactant (rhamnolipid) were introduced. The presence of DOM in the aqueous phase could decrease the sorption of PAHs, thus influence their mobility. Desorption enhancement for both PHE and PYR in the system with compost DOM was greater than that in the soil DOM system. This is due to the differences in specific molecular structures and functional groups of two DOMs. With the co-existence of biosurfactant and DOM, partitioning is the predominant process and the desorption extent was much higher than the system with DOM or biosurfactant individually. For PHE, the desorption enhancement of combined DOM and biosurfactant was larger than the sum of DOM or biosurfactant; however desorption enhancement for PYR in the combined system was less than the additive enhancement in two individual system under low PAH concentration. This could be explained as the competition sorption among PAHs, DOM and biosurfactant. The results of this study will help to clarify the transport of petroleum pollutants in the remediation of HOCs-contaminated soils.

Crude glycerol from biodiesel industry as substrate for biosurfactant production by Bacillus subtilis ATCC 6633

Directory of Open Access Journals (Sweden)

Marylane de Sousa

2014-04-01

Full Text Available Glycerol, a co-product of the biodiesel industry, may be a suitable raw material for the production of high added-value compounds by the microorganisms. This study aimed to use the glycerol obtained from the biodiesel production process as the main carbon source for biosurfactant production by Bacillus subtilis ATCC 6633. Results indicated that the strain lowered the surface tension of the cell-free fermented broth to 31.5 ± 1.6 mN/m, indicating the production of biosurfactant. The critical micelle concentration (CMC = 33.6 mN/m obtained was similar to the previously reported for biossurfactants isolated from other Bacillus. The produced biosurfactant was able to emulsify n-hexadecane and soybean oil.

Biosurfactants from thermophilic dairy streptococci and their potential role in the fouling control of heat exchanger plates

NARCIS (Netherlands)

Busscher, HJ; vanderKuijlBooij, M; vanderMei, HC

Recent work on biosurfactant release by thermophilic dairy streptococci is reviewed, There is a suggestion that Streptococcus thermophilus isolates may release biosurfactants that stimulate detachment of already-adhering cells and leave an anti-adhesive coating on a substratum. A previously

Removal of Cadmium and Zinc from Soil using Immobilized Cell of Biosurfactant Producing Bacteria

Directory of Open Access Journals (Sweden)

Charoon Sarin

2010-07-01

Full Text Available Immobilized biosurfactant producing bacteria (Bacillus subtilis TP8 and Pseudomonas fluorescens G7 were assessed for survival in heavy metal contaminated soil and for their ability to remove cadmium and zinc from contaminated soil. P. fluorescens G7 was considered to be a good candidate for bioremediation of heavy metals because of its high minimum inhibitory concentrations (MIC for each heavy metal and because of the obviously increased numbers of cell surviving after incubation in the heavy metal contaminated soil up to 4 weeks. The results of soil remediation showed that approximately 19% of Zn and 16.7% of Cd could be removed by this immobilized biosurfactant producing bacteria after incubation for 2 weeks. The results confirm the potential applicability of the immobilized biosurfactant producing bacteria for heavy metal bioremediation.

Applications of biosurfactants in the petroleum industry and the remediation of oil spills.

Science.gov (United States)

de Cássia F S Silva, Rita; Almeida, Darne G; Rufino, Raquel D; Luna, Juliana M; Santos, Valdemir A; Sarubbo, Leonie Asfora

2014-07-15

Petroleum hydrocarbons are important energy resources. However, petroleum is also a major pollutant of the environment. Contamination by oil and oil products has caused serious harm, and increasing attention has been paid to the development and implementation of innovative technologies for the removal of these contaminants. Biosurfactants have been extensively used in the remediation of water and soil, as well as in the main stages of the oil production chain, such as extraction, transportation, and storage. This diversity of applications is mainly due to advantages such as biodegradability, low toxicity and better functionality under extreme conditions in comparison to synthetic counterparts. Moreover, biosurfactants can be obtained with the use of agro-industrial waste as substrate, which helps reduce overall production costs. The present review describes the potential applications of biosurfactants in the oil industry and the remediation of environmental pollution caused by oil spills.

Applications of Biosurfactants in the Petroleum Industry and the Remediation of Oil Spills

Directory of Open Access Journals (Sweden)

Rita de Cássia F. S. Silva

2014-07-01

Full Text Available Petroleum hydrocarbons are important energy resources. However, petroleum is also a major pollutant of the environment. Contamination by oil and oil products has caused serious harm, and increasing attention has been paid to the development and implementation of innovative technologies for the removal of these contaminants. Biosurfactants have been extensively used in the remediation of water and soil, as well as in the main stages of the oil production chain, such as extraction, transportation, and storage. This diversity of applications is mainly due to advantages such as biodegradability, low toxicity and better functionality under extreme conditions in comparison to synthetic counterparts. Moreover, biosurfactants can be obtained with the use of agro-industrial waste as substrate, which helps reduce overall production costs. The present review describes the potential applications of biosurfactants in the oil industry and the remediation of environmental pollution caused by oil spills.

Analysis of biosurfactants from industrially-viable Pseudomonas strain isolated from crude oil suggests how rhamnolipids congeners affect on emulsification property and antimicrobial activity

Directory of Open Access Journals (Sweden)

Palashpriya eDas

2014-12-01

Full Text Available Rhamnolipid biosurfactants produced mainly by Pseudomonas sp. had been reported to possess a wide range of potential industrial application. These biosurfactants are produced as monorhamnolipid (MRL and di-rhamnolipid (DRL congeners. The present study deals with rhamnolipid biosurfactants produced by three bacterial isolates from crude oil. Biosurfactants produced by one of the strains (named as IMP67 was found to be very efficacious based on its critical micelle concentration (CMC value and hydrocarbon emulsification property. Strikingly, antimicrobial and anti-biofilm potential of this biosurfactant were higher than biosurfactants produced by other two strains. Thin layer chromatography (TLC analysis and rhamnose quantification showed that the rhamnolipids of IMP67 had more MRL congeners than biosurfactants of the other two strains. Emulsification and antimicrobial actions were affected by manual change of MRL and DRL congener proportions. Increase of MRL proportion enhanced emulsification index and antimicrobial property to Gram negative bacteria. This result indicated that the ratio of MRL and DRL affect the emulsification potentials of rhamnolipids, and suggested that high emulsification potentials might enhance rhamnolipids to penetrate the cell wall of Gram negative bacteria. In consistent, rhamnolipids of IMP67 reduced the MIC of some antibiotics against bacteria, suggesting the potential of biosurfactant as antibiotics synergist.

Optimization and characterization of biosurfactant production from kitchen waste oil using Pseudomonas aeruginosa.

Science.gov (United States)

Chen, Chunyan; Sun, Ni; Li, Dongsheng; Long, Sihua; Tang, Xiaoyu; Xiao, Guoqing; Wang, Linyuan

2018-03-16

Kitchen waste oil (KWO) from catering industries or households was used as a low-cost carbon source for producing biosurfactants by self-isolated Pseudomonas aeruginosa. Fermentation performance with KWO was superior to those with four other carbon sources, with higher optical density (OD 600 ) of 2.33 and lower interfacial tension of 0.57 mN/m. Culture conditions for biosurfactant production were optimized, with optimal pH of 8.0 and nitrogen source concentration of 2.0 g/L, respectively. The results of infrared spectroscopy and liquid chromatography-mass spectrometry (LC-MS) showed that the biosurfactant was a mixture of six rhamnolipid congeners, among which Rha-Rha-C 10 -C 10 and Rha-C 10 -C 10 were the main components, with mass fraction of approximately 34.20 and 50.86%, respectively. The critical micelle concentration (CMC) obtained was 55.87 mg/L. In addition, the rhamnolipids exhibited excellent tolerance to temperature (20-100 °C), pH (6.0-12.0), and salinity (2-20%; w/v) in a wide range, thereby showing good stability to extreme environmental conditions. The rhamnolipids positively affected oil removal from oil sludge and KWO-contaminated cotton cloth, with removal rate of 34.13 and of 30.92%, respectively. Our results demonstrated that biosurfactant production from KWO was promising, with advantages of good performance, low cost and environmental safety.

Trehalose lipid biosurfactants produced by the actinomycetes Tsukamurella spumae and T. pseudospumae.

Science.gov (United States)

Kügler, Johannes H; Muhle-Goll, Claudia; Kühl, Boris; Kraft, Axel; Heinzler, Raphael; Kirschhöfer, Frank; Henkel, Marius; Wray, Victor; Luy, Burkhard; Brenner-Weiss, Gerald; Lang, Siegmund; Syldatk, Christoph; Hausmann, Rudolf

2014-11-01

Actinomycetales are known to produce various secondary metabolites including products with surface-active and emulsifying properties known as biosurfactants. In this study, the nonpathogenic actinomycetes Tsukamurella spumae and Tsukamurella pseudospumae are described as producers of extracellular trehalose lipid biosurfactants when grown on sunflower oil or its main component glyceryltrioleate. Crude extracts of the trehalose lipids were purified using silica gel chromatography. The structure of the two trehalose lipid components (TL A and TL B) was elucidated using a combination of matrix-assisted laser desorption/ionization time-of-flight/time-of-flight/tandem mass spectroscopy (MALDI-ToF-ToF/MS/MS) and multidimensional NMR experiments. The biosurfactants were identified as 1-α-glucopyranosyl-1-α-glucopyranosid carrying two acyl chains varying of C4 to C6 and C16 to C18 at the 2' and 3' carbon atom of one sugar unit. The trehalose lipids produced demonstrate surface-active behavior and emulsifying capacity. Classified as risk group 1 organisms, T. spumae and T. pseudospumae hold potential for the production of environmentally friendly surfactants.

Using Biosurfactants Produced from Agriculture Process Waste Streams to Improve Oil Recovery in Fractured Carbonate Reservoirs

Energy Technology Data Exchange (ETDEWEB)

Stephen Johnson; Mehdi Salehi; Karl Eisert; Sandra Fox

2009-01-07

This report describes the progress of our research during the first 30 months (10/01/2004 to 03/31/2007) of the original three-year project cycle. The project was terminated early due to DOE budget cuts. This was a joint project between the Tertiary Oil Recovery Project (TORP) at the University of Kansas and the Idaho National Laboratory (INL). The objective was to evaluate the use of low-cost biosurfactants produced from agriculture process waste streams to improve oil recovery in fractured carbonate reservoirs through wettability mediation. Biosurfactant for this project was produced using Bacillus subtilis 21332 and purified potato starch as the growth medium. The INL team produced the biosurfactant and characterized it as surfactin. INL supplied surfactin as required for the tests at KU as well as providing other microbiological services. Interfacial tension (IFT) between Soltrol 130 and both potential benchmark chemical surfactants and crude surfactin was measured over a range of concentrations. The performance of the crude surfactin preparation in reducing IFT was greater than any of the synthetic compounds throughout the concentration range studied but at low concentrations, sodium laureth sulfate (SLS) was closest to the surfactin, and was used as the benchmark in subsequent studies. Core characterization was carried out using both traditional flooding techniques to find porosity and permeability; and NMR/MRI to image cores and identify pore architecture and degree of heterogeneity. A cleaning regime was identified and developed to remove organic materials from cores and crushed carbonate rock. This allowed cores to be fully characterized and returned to a reproducible wettability state when coupled with a crude-oil aging regime. Rapid wettability assessments for crushed matrix material were developed, and used to inform slower Amott wettability tests. Initial static absorption experiments exposed limitations in the use of HPLC and TOC to determine

Characterization and properties of biosurfactants produced by a newly isolated strain Bacillus methylotrophicus DCS1 and their applications in enhancing solubility of hydrocarbon.

Science.gov (United States)

Jemil, Nawel; Ben Ayed, Hanen; Hmidet, Noomen; Nasri, Moncef

2016-11-01

Six biosurfactant-producing bacteria were isolated from hydrocarbon contaminated soils in Sfax, Tunisia. Isolates were screened for biosurfactant production by different conventional methods including hemolytic activity, surface tension reduction, drop-collapsing and oil displacement tests. All these screening tests show that all the isolates behave differently. Among the isolated bacteria, DCS1 strain was selected for further studies based on its highest activities and it was identified as Bacillus methylotrophicus DCS1. This strain was found to be a potent producer of biosurfactant when cultivated in mineral-salts medium supplemented with diesel oil (2 %, v/v) as a sole carbon source. Physicochemical properties and stability of biosurfactants synthesized by B. methylotrophicus DCS1 were investigated. The produced biosurfactants DCS1, from Landy medium, possess high surface activity that could lower the surface tension of water to a value of 31 from 72 mN m(-1) and have a critical micelle concentration (CMC) of 100 mg L(-1). Compared with SDS and Tween 80, biosurfactants showed excellent emulsification activities against different hydrocarbon substrates and high solubilization efficiency towards diesel oil. Biosurfactants DCS1 showed good stability in a wide range of temperature, pH and salinity. These results suggested that biosurfactants produced by B. methylotrophicus DCS1 could be an alternative to chemically synthesized surfactants for use in bioremediation processes to enhance the solubility of hydrophobic compounds.

The use of hydrodynamic disintegration as a means to improve anaerobic digestion of activated sludge

OpenAIRE

Machnicka, A; Grűbel, K; Suschka, J

2009-01-01

Disintegration by hydrodynamic cavitation has a positive effect on the degree and rate of sludge anaerobic digestion. By applying hydrodynamic disintegration the lysis of cells occurs in minutes instead of days. The intracellular and extracellular components are set free and are immediately available for biological degradation which leads to an improvement of the subsequent anaerobic process. Hydrodynamic disintegration of the activated sludge results in organic matter and a polymer transfer ...

Bioproduction and anticancer activity of biosurfactant produced by the dematiaceous fungus Exophiala dermatitidis SK80.

Science.gov (United States)

Chiewpattanakul, Paramaporn; Phonnok, Sirinet; Durand, Alain; Marie, Emmanuelle; Thanomsub, Benjamas Wongsatayanon

2010-12-01

A new biosurfactant producer was isolated from palm-oilcontaminated soil and later identified through morphology and DNA sequencing as the yeast-like fungus Exophiala dermatitidis. Biosurfactant production was catalyzed by vegetable oil, supplemented with a basal medium. The culture conditions that provided the biosurfactant with the highest surface activity were found to be 5% palm oil with 0.08% NH4NO3, at a pH of 5.3, with shaking at 200 rpm, and a temperature of 30 degrees C for a 14-day period of incubation. The biosurfactant was purified, in accordance with surfactant properties, by solvent fractionation using silica gel column chromatography. The chemical structure of the strongest surface-active compound was elucidated through the use of NMR and mass spectroscopy, and noted to be monoolein, which then went on to demonstrate antiproliferative activity against cervical cancer (HeLa) and leukemia (U937) cell lines in a dose-dependent manner. Interestingly, no cytotoxicity was observed with normal cells even when high concentrations were used. Cell and DNA morphological changes, in both cancer cell lines, were observed to be cell shrinkage, membrane blebbling, and DNA fragmentation.

Analysis of biosurfactants from industrially viable Pseudomonas strain isolated from crude oil suggests how rhamnolipids congeners affect emulsification property and antimicrobial activity.

Science.gov (United States)

Das, Palashpriya; Yang, Xin-Ping; Ma, Luyan Z

2014-01-01

Rhamnolipid biosurfactants produced mainly by Pseudomonas sp. had been reported to possess a wide range of potential industrial application. These biosurfactants are produced as monorhamnolipid (MRL) and di-rhamnolipid (DRL) congeners. The present study deals with rhamnolipid biosurfactants produced by three bacterial isolates from crude oil. Biosurfactants produced by one of the strains (named as IMP67) was found to be very efficacious based on its critical micelle concentration value and hydrocarbon emulsification property. Strikingly, antimicrobial, and anti-biofilm potential of this biosurfactant were higher than biosurfactants produced by other two strains. Thin layer chromatography analysis and rhamnose quantification showed that the rhamnolipids of IMP67 had more MRL congeners than biosurfactants of the other two strains. Emulsification and antimicrobial actions were affected by manual change of MRL and DRL congener proportions. Increase of MRL proportion enhanced emulsification index and antimicrobial property to Gram negative bacteria. This result indicated that the ratio of MRL and DRL affected the emulsification potentials of rhamnolipids, and suggested that high emulsification potentials might enhance rhamnolipids to penetrate the cell wall of Gram negative bacteria. In line with this finding, rhamnolipids of IMP67 also reduced the MIC of some antibiotics against bacteria, suggesting their synergistic role with the antibiotics.

A novel biosurfactant produced by Aureobasidium pullulans L3-GPY from a tiger lily wild flower, Lilium lancifolium Thunb.

Science.gov (United States)

Kim, Jong Shik; Lee, In Kyoung; Yun, Bong Sik

2015-01-01

Yeast biosurfactants are important biotechnological products in the food industry, and they have medical and cosmeceutical applications owing to their specific modes of action, low toxicity, and applicability. Thus, we have isolated and examined biosurfactant-producing yeast for various industrial and medical applications. A rapid and simple method was developed to screen biosurfactant-producing yeasts for high production of eco-friendly biosurfactants. Using this method, several potential niches of biosurfactant-producing yeasts, such as wild flowers, were investigated. We successfully selected a yeast strain, L3-GPY, with potent surfactant activity from a tiger lily, Lilium lancifolium Thunb. Here, we report the first identification of strain L3-GPY as the black yeast Aureobasidium pullulans. In addition, we isolated a new low-surface-tension chemical, designated glycerol-liamocin, from the culture supernatant of strain L3-GPY through consecutive chromatography steps, involving an ODS column, solvent partition, silica gel, Sephadex LH-20, and an ODS Sep-Pak cartridge column. The chemical structure of glycerol-liamocin, determined by mass spectrometry and nuclear magnetic resonance spectroscopy, indicates that it is a novel compound with the molecular formula C33H62O12. Furthermore, glycerol-liamocin exhibited potent biosurfactant activity (31 mN/m). These results suggest that glycerol-liamocin is a potential novel biosurfactantfor use in various industrial applications.

Utilization of palm oil decanter cake as a novel substrate for biosurfactant production from a new and promising strain of Ochrobactrum anthropi 2/3.

Science.gov (United States)

Noparat, Pongsak; Maneerat, Suppasil; Saimmai, Atipan

2014-03-01

A biosurfactant-producing bacterium, isolate 2/3, was isolated from mangrove sediment in the south of Thailand. It was evaluated as a potential biosurfactant producer. The highest biosurfactant production (4.52 g/l) was obtained when the cells were grown on a minimal salt medium containing 25 % (v/v) palm oil decanter cake and 1 % (w/v) commercial monosodium glutamate as carbon and nitrogen sources, respectively. After microbial cultivation at 30 °C in an optimized medium for 96 h, the biosurfactant produced was found to reduce the surface tension of pure water to 25.0 mN/m with critical micelle concentrations of 8.0 mg/l. The stability of the biosurfactant at different salinities, pH and temperature and also its emulsifying activity was investigated. It is an effective surfactant at very low concentrations over a wide range of temperatures, pH and salt concentrations. The biosurfactant obtained was confirmed as a glycolipid type biosurfactant by using a biochemical test, fourier-transform infrared spectroscopy, MNR and mass spectrometry. The crude biosurfactant showed a broad spectrum of antimicrobial activity and also had the ability to emulsify oil and enhance polyaromatic hydrocarbons solubility.

Synthesis, characterization, and oil recovery application of biosurfactant produced by indigenous pseudomonas aeruginosa WJ-1 using waste vegetable oils.

Science.gov (United States)

Xia, Wen-Jie; Luo, Zhi-Bin; Dong, Han-Ping; Yu, Li; Cui, Qing-Feng; Bi, Yong-Qiang

2012-03-01

A bacterial strain was isolated and cultured from the oil excavation areas in tropical zone in northern China. The biochemical characteristics and partial sequenced 16S rRNA gene of isolate, WJ-1, was identical to those of cultured representatives of the species Pseudomonas aeruginosa. This bacterium was able to produce a type of biosurfactant. Compositional analysis revealed that the extracted biosurfactant was composed of high percentage lipid (∼74%, w/w) and carbohydrate (∼20%, w/w) in addition to a minor fraction of protein (∼6%, w/w). The best production of 50.2 g/l was obtained when the cells were grown on minimal salt medium containing 6.0% (w/v) glucose and 0.75% (w/v) sodium nitrate supplemented with 0.1% (v/v) element solution at 37 °C and 180 rpm after 96 h. The optimum biosurfactant production pH value was found to be 6.0-8.0. The biosurfactant of WJ-1, with the critical micelle concentration of 0.014 g/L, could reduce surface tension to 24.5 mN/m and emulsified kerosene up to EI(24) ≈95. The results obtained from time course study indicated that the surface tension reduction and emulsification potential was increased in the same way to cell growth. However, maximum biosurfactant production occurred and established in the stationary growth phase (after 90 h). Thin layer chromatography, Fourier transform infrared spectrum, and mass spectrum analysis indicate the extracted biosurfactant was affiliated with rhamnolipid. The core holder flooding experiments demonstrated that the oil recovery efficiency of strain and its biosurfactant was 23.02% residual oil.

Effect of two types of biosurfactants on phenanthrene availability to the bacterial bioreporter Burkholderia sartisoli strain RP037

NARCIS (Netherlands)

Tecon, R.; Van der Meer, J.R.

2010-01-01

Biosurfactants are tensio-active agents that have often been proposed as a means to enhance the aqueous solubility of hydrophobic organic contaminants, such as polycyclic aromatic hydrocarbons (PAHs). Biosurfactant-producing bacteria such as those belonging to the genus Pseudomonas might therefore

Combined electrical-alkali pretreatment to increase the anaerobic hydrolysis rate of waste activated sludge during anaerobic digestion

International Nuclear Information System (INIS)

Zhen, Guangyin; Lu, Xueqin; Li, Yu-You; Zhao, Youcai

2014-01-01

Highlights: • Combined electrical-alkali pretreatment for improving sludge anaerobic digestion was proposed. • Combined process enhanced the cell lysis, biopolymers releases, and thus sludge disintegration. • Increased solubilization of sludge increased the anaerobic hydrolysis rate. • Increased solubilization does not always induce an improved anaerobic digestion efficiency. - Abstract: Pretreatment can be used prior to anaerobic digestion to improve the efficiency of waste activated sludge (WAS) digestion. In this study, electrolysis and a commonly used pretreatment method of alkaline (NaOH) solubilization were integrated as a pretreatment method for promoting WAS anaerobic digestion. Pretreatment effectiveness of combined process were investigated in terms of disintegration degree (DD SCOD ), suspended solids (TSS and VSS) removals, the releases of protein (PN) and polysaccharide (PS), and subsequent anaerobic digestion as well as dewaterability after digestion. Electrolysis was able to crack the microbial cells trapped in sludge gels and release the biopolymers (PN and PS) due to the cooperation of alkaline solubilization, enhancing the sludge floc disintegration/solubilization, which was confirmed by scanning electron microscopy (SEM) analysis. Biochemical methane potential (BMP) assays showed the highest methane yield was achieved with 5 V plus pH 9.2 pretreatment with up to 20.3% improvement over the non-pretreated sludge after 42 days of mesophilic operation. In contrast, no discernible improvements on anaerobic degradability were observed for the rest of pretreated sludges, probably due to the overmuch leakage of refractory soluble organics, partial chemical mineralization of solubilized compounds and sodium inhibition. The statistical analysis further indicated that increased solubilization induced by electrical-alkali pretreatment increased the first-order anaerobic hydrolysis rate (k hyd ), but had no, or very slight enhancement on WAS ultimate

Sulfur source-mediated transcriptional regulation of the rhlABC genes involved in biosurfactants production by Pseudomonas sp. strain AK6U.

Science.gov (United States)

Ismail, Wael; El Nayal, Ashraf M; Ramadan, Ahmed R; Abotalib, Nasser

2014-01-01

Despite the nutritional significance of sulfur, its influence on biosurfactants production has not been sufficiently studied. We investigated the expression of key biosurfactants production genes, rhlABC, in cultures of Pseudomonas sp. AK6U grown with inorganic or organic sulfur sources. AK6U grew with either inorganic sulfate (MgSO4), dibenzothiophene (DBT), or DBT-sulfone as a sole sulfur source in the presence of glucose as a carbon source. The AK6U cultures produced variable amounts of biosurfactants depending on the utilized sulfur source. Biosurfactants production profile of the DBT cultures was significantly different from that of the DBT-sulfone and inorganic sulfate cultures. The last two cultures were very similar in terms of biosurfactants productivity. Biosurfactants yield in the DBT cultures (1.3 g/L) was higher than that produced by the DBT-sulfone (0.5 g/L) and the inorganic sulfate (0.44 g/L) cultures. Moreover, the surface tension reduction in the DBT cultures (33 mN/m) was much stronger than that measured in the DBT-sulfone (58 mN/m) or inorganic sulfate (54 mN/m) cultures. RT-qPCR revealed variations in the expression levels of the rhlABC genes depending on the sulfur source. The DBT cultures had higher expression levels for the three genes as compared to the DBT-sulfone and inorganic sulfate cultures. There was no significant difference in the expression profiles between the DBT-sulfone and the MgSO4 cultures. The increased expression of rhlC in the DBT cultures is indicative for production of higher amounts of dirhamnolipids compared to the DBT-sulfone and inorganic sulfate cultures. The gene expression results were in good agreement with the biosurfactants production yields and surface tension measurements. The sulfur source mediates a fine-tuned mechanism of transcriptional regulation of biosurfactants production genes. Our findings can have an impact on industrial production of biosurfactants and other biotechnological processes like

Effects of biosurfactants on the viability and proliferation of human breast cancer cells.

Science.gov (United States)

Duarte, Cristina; Gudiña, Eduardo J; Lima, Cristovao F; Rodrigues, Ligia R

2014-01-01

Biosurfactants are molecules with surface activity produced by microorganisms that can be used in many biomedical applications. The anti-tumour potential of these molecules is being studied, although results are still scarce and few data are available regarding the mechanisms underlying such activity. In this work, the anti-tumour activity of a surfactin produced by Bacillus subtilis 573 and a glycoprotein (BioEG) produced by Lactobacillus paracasei subsp. paracasei A20 was evaluated. Both biosurfactants were tested against two breast cancer cell lines, T47D and MDA-MB-231, and a non-tumour fibroblast cell line (MC-3 T3-E1), specifically regarding cell viability and proliferation. Surfactin was found to decrease viability of both breast cancer cell lines studied. A 24 h exposure to 0.05 g l(-1) surfactin led to inhibition of cell proliferation as shown by cell cycle arrest at G1 phase. Similarly, exposure of cells to 0.15 g l(-1) BioEG for 48 h decreased cancer cells' viability, without affecting normal fibroblasts. Moreover, BioEG induced the cell cycle arrest at G1 for both breast cancer cell lines. The biosurfactant BioEG was shown to be more active than surfactin against the studied breast cancer cells. The results gathered in this work are very promising regarding the biosurfactants potential for breast cancer treatment and encourage further work with the BioEG glycoprotein.

Production of microbial glycolipid biosurfactants and their antimicrobial activity

Science.gov (United States)

Microbial glycolipids produced by bacteria or yeast as secondary metabolites, such as sophorolipids (SLs), rhamnolipids (RLs) and mannosylerythritol lipids (MELs) are “green” biosurfactants desirable in a bioeconomy. High cost of production is a major hurdle toward widespread commercial use of bios...

Investigation of antimicrobial activity and statistical optimization of Bacillus subtilis SPB1 biosurfactant production in solid-state fermentation.

Science.gov (United States)

Ghribi, Dhouha; Abdelkefi-Mesrati, Lobna; Mnif, Ines; Kammoun, Radhouan; Ayadi, Imen; Saadaoui, Imen; Maktouf, Sameh; Chaabouni-Ellouze, Semia

2012-01-01

During the last years, several applications of biosurfactants with medical purposes have been reported. Biosurfactants are considered relevant molecules for applications in combating many diseases. However, their use is currently extremely limited due to their high cost in relation to that of chemical surfactants. Use of inexpensive substrates can drastically decrease its production cost. Here, twelve solid substrates were screened for the production of Bacillus subtilis SPB1 biosurfactant and the maximum yield was found with millet. A Plackett-Burman design was then used to evaluate the effects of five variables (temperature, moisture, initial pH, inoculum age, and inoculum size). Statistical analyses showed that temperature, inoculum age, and moisture content had significantly positive effect on SPB1 biosurfactant production. Their values were further optimized using a central composite design and a response surface methodology. The optimal conditions of temperature, inoculum age, and moisture content obtained under the conditions of study were 37°C, 14 h, and 88%, respectively. The evaluation of the antimicrobial activity of this compound was carried out against 11 bacteria and 8 fungi. The results demonstrated that this biosurfactant exhibited an important antimicrobial activity against microorganisms with multidrug-resistant profiles. Its activity was very effective against Staphylococcus aureus, Staphylococcus xylosus, Enterococcus faecalis, Klebsiella pneumonia, and so forth.

Biosurfactants production and possible uses in microbial enhanced oil recovery and oil pollution remediation: a review

International Nuclear Information System (INIS)

Banat, I.M.

1995-01-01

Surfactants are widely used for various purposes in industry, but for many years were mainly chemically synthesized. It has only been in the past few decades that biological surface-active compounds (biosurfactants) have been described. Biosurfactants are gaining prominence and have already taken over for a number of important industrial uses, due to their advantages of biodegradability, production on renewable resources and functionality under extreme conditions; particularly those pertaining during tertiary crude-oil recovery. Conflicting reports exist concerning their efficacy and the economics of both their production and application. The limited successes and applications for biosurfactants production, recovery, use in oil pollution control, oil storage tank clean-up and enhanced oil-recovery are reviewed from the technical point of view. (author)

Characterization of biosurfactants produced by the oil-degrading bacterium Rhodococcus erythropolis S67 at low temperature.

Science.gov (United States)

Luong, T M; Ponamoreva, O N; Nechaeva, I A; Petrikov, K V; Delegan, Ya A; Surin, A K; Linklater, D; Filonov, A E

2018-01-04

Production of trehalolipid biosurfactants by Rhodococcus erythropolis S67 depending on the growth temperature was studied. R. erythropolis S67 produced glycolipid biosurfactants such as 2,3,4-succinoyl-octanoyl-decanoyl-2'-decanoyl trehalose and 2,3,4-succinoyl-dioctanoyl-2'-decanoyl trehalose during the growth in n-hexadecane medium at 26 and 10 °C, despite the different aggregate state of the hydrophobic substrate at low temperature. The surface tension of culture medium was found being reduced from 72 to 27 and 45 mN m -1 , respectively. Production of trehalolipid biosurfactants by R. erythropolis S67 at low temperature could be useful for the biodegradation of petroleum hydrocarbons at low temperatures by enhancing the bioremediation performance in cold regions.

USE OF BUTTER MILK AND POULTRY-TRANSFORMING WASTES FOR ENHANCED PRODUCTION OF Bacillus subtilis SPB1 BIOSURFACTANT IN SUBMERGED FERMENTATION

Directory of Open Access Journals (Sweden)

Raida Zouari

2015-04-01

Full Text Available Biosurfactants are valuable microbial amphiphilic molecules with effective surface-active and biological properties applicable to several industries and processes. Microorganisms synthesize them, especially during growth on water-immiscible substrates, providing an alternative to chemically prepared conventional surfactants. Microbial surfactants are not yet a sustainable alternative to chemically synthesized surfactants seeing their potentially high production charges. This study highlights the use of low-cost agro-industrial raw material for fermentative production of biosurfactants. The Box–Behnken Design and response surface methodology were employed to optimize the concentrations of the ratio butter milk /distilled water, poultry-transforming wastes and inoculum size for lipopeptide biosurfactant production by B.subtilis SPB1 in submerged fermentation.The best production yield was about 12.61 ± 0.7 g/L of crude lipopeptide biosurfactant. It can be obtained when using a ratio butter milk /distilled water of 1.5, poultry-transforming wastes of 23g/L and an inoculum size of 0.12. In comparison to the highest biosurfactant production yield reported for Bacillus subtilis SPB1, three fold increases were obtained.

Mechanisms of the stimulatory effects of rhamnolipid biosurfactant on rice straw hydrolysis

Energy Technology Data Exchange (ETDEWEB)

Zhang, Qiuzhuo; He, Guofu; Xu, Yatong [Department of Environmental Science, East China Normal University, 3663 North Zhongshan Road, Putuo District, Shanghai 200062 (China); Wang, Juan [Department of Environmental Science and Engineering, Harbin Institute of Technology, Harbin 150090 (China); Cai, Weimin [Department of Environmental Science and Engineering, Harbin Institute of Technology, Harbin 150090 (China); School of Environmental Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China)

2009-11-15

Rhamnolipid biosurfactant, as an addition to rice straw hydrolysis bioprocess, could not only stimulate the hydrolysis rate, but also reduce the requirement for large amount of cellulases and promote its recycling process. In this article, through the observation of the changes of cellulases, microorganism, substrate and their mutual functions, the mechanisms of the stimulatory effect of rhamnolipid on rice straw hydrolysis were investigated. The study found that the addition of rhamnolipid increases the activity of {beta}-glucosidase but stabilizes Cel7A activity. The observed results might be the main mechanisms triggering the stimulatory effect of adding biosurfactants on rice straw hydrolysis. Meanwhile, zeta potential of the substrate increased, which could make the resistance of the cell attached to the substrate weaker. This in turn could facilitate easy adhesion and better retention of the microbial cell in the media. Moreover, we discovered that lignin content played an important role in the stimulatory effect of adding rhamnolipid. The adsorption of rhamnolipid biosurfactant prevented unproductive binding of enzymes to lignin. This could be another important mechanism responsible for the stimulatory effects of adding rhamnolipid on rice straw hydrolysis. (author)

Halomonas sp. BS4, A biosurfactant producing halophilic bacterium isolated from solar salt works in India and their biomedical importance

OpenAIRE

Donio, Mariathason Birdilla Selva; Ronica, Fernando Arul; Viji, Vijayaragavan Thanga; Velmurugan, Subramanian; Jenifer, John Selesteen Charles Adlin; Michaelbabu, Mariavincent; Dhar, Prasenjit; Citarasu, Thavasimuthu

2013-01-01

Halophilic bacteria were isolated from Thamaraikulam solar salt works in India. After routine biosurfactant screening by various methods, the biosurfactant producing bacteria, Halomonas sp BS4 was confirmed by 16?S rRNA sequencing. The growth optimization of Halomonas sp BS4 revealed their optimum growth at 8% NaCl and 6-8?pH in the growth medium. Further the partially purified biosurfactants were characterized by TLC, FTIR and GC-MS analysis. GC-MS results revealed that, the partial purified...

Antioxidant and antiproliferative potential of biosurfactants isolated from Lactobacillus casei and their anti-biofilm effect in oral Staphylococcus aureus strains.

Science.gov (United States)

Merghni, Abderrahmen; Dallel, Ines; Noumi, Emira; Kadmi, Yassine; Hentati, Hajer; Tobji, Samir; Ben Amor, Adel; Mastouri, Maha

2017-03-01

Biosurfactants also called bioemulsifiers are amphipathic compounds produced by many microorganisms that allow them to exhibit a wide range of biological activities. The aim of this study was to determine the antioxidant and antiproliferative potential of biosurfactants isolated from Lactobacillus casei and to assess their anti-adhesive and anti-biofilm abilities against oral opportunistic Staphylococcus aureus strains. The antioxidant activity of biosurfactant was evaluated using the in vitro scavenging ability on 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical. The antiproliferative activity was determined on epithelial cell line (HEp-2) by the Methylthiazole tetrazolium (MTT) reduction assay. The anti-adhesive and antibiofilm activity against S. aureus strains were achieved using crystal violet staining. Our results revealed that the DPPH scavenging activity of biosurfactants at 5.0 mg/mL concentration is between 74.6 and 77.3%. Furthermore, biosurfactants showed antiproliferative potency against studied epithelial cells as judged by IC50 and its value ranged from 109.1 ± 0.84 mg/mL to 129.7 ± 0.52 mg/mL. The results of the growth inhibition indicate that biosurfactant BS-LBl was more effective against oral S. aureus strains 9P and 29P with an IC50 of 1.92 ± 0.26 mg/mL and 2.16 ± 0.12 mg/mL respectively. Moreover, both biosurfactants displayed important antibiofilm activity with eradication percentages ranging from 80.22 ± 1.33% to 86.21 ± 2.94% for the BS-LBl, and from 53.38 ± 1.77% to 64.42 ± 2.09% for the BS-LZ9. Our findings demonstrate that biosurfactants from L. casei strains exhibited considerable antioxidant and antiproliferative potencies and were able to inhibit oral S. aureus strains with important antibiofilm efficacy. They could have a promising role in the prevention of oral diseases. Copyright © 2017 Elsevier Ltd. All rights reserved.

Production of microbial biosurfactants: Status quo of rhamnolipid and surfactin towards large-scale production.

Science.gov (United States)

Henkel, Marius; Geissler, Mareen; Weggenmann, Fabiola; Hausmann, Rudolf

2017-07-01

Surfactants are an important class of industrial chemicals. Nowadays oleochemical surfactants such as alkyl polyglycosides (APGs) become increasingly important. This trend towards the utilization of renewable resources continues and consumers increasingly demand for environmentally friendly products. Consequently, research in microbial surfactants has drastically increased in the last years. While for mannosylerythritol lipids and sophorolipids established industrial processes exist, an implementation of other microbially derived surfactants has not yet been achieved. Amongst these biosurfactants, rhamnolipids synthesized by Pseudomonas aeruginosa and surfactin produced by Bacillus subtilis are so far the most analyzed biosurfactants due to their exceptional properties and the concomitant possible applications. In this review, a general overview is given regarding the current status of biosurfactants and benefits attributed to these molecules. Furthermore, the most recent research approaches for both rhamnolipids and surfactin are presented with respect to possible methods for industrial processes and the occurring drawbacks and limitations researchers have to address and overcome. Copyright © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Supporting data for identification of biosurfactant-producing bacteria isolated from agro-food industrial effluent

Science.gov (United States)

Fulazzaky, Mohamad Ali; Abdullah, Shakila; Salim, Mohd Razman

2016-01-01

The goal of this study was to identify the biosurfactant-producing bacteria isolated from agro-food industrial effluet. The identification of the potential bacterial strain using a polymerase chain reaction of the 16S rRNA gene analysis was closely related to Serratia marcescens with its recorded strain of SA30 “Fundamentals of mass transfer and kinetics for biosorption of oil and grease from agro-food industrial effluent by Serratia marcescens SA30” (Fulazzaky et al., 2015) [1]; however, many biochemical tests have not been published yet. The biochemical tests of biosurfactant production, haemolytic assay and cell surface hydrophobicity were performed to investigate the beneficial strain of biosurfactant-producing bacteria. Here we do share data collected from the biochemical tests to get a better understanding of the use of Serratia marcescens SA30 to degrade oil, which contributes the technical features of strengthening the biological treatment of oil-contaminated wastewater in tropical environments. PMID:27077083

Supporting data for identification of biosurfactant-producing bacteria isolated from agro-food industrial effluent

Directory of Open Access Journals (Sweden)

Mohamad Ali Fulazzaky

2016-06-01

Full Text Available The goal of this study was to identify the biosurfactant-producing bacteria isolated from agro-food industrial effluet. The identification of the potential bacterial strain using a polymerase chain reaction of the 16S rRNA gene analysis was closely related to Serratia marcescens with its recorded strain of SA30 “Fundamentals of mass transfer and kinetics for biosorption of oil and grease from agro-food industrial effluent by Serratia marcescens SA30” (Fulazzaky et al., 2015 [1]; however, many biochemical tests have not been published yet. The biochemical tests of biosurfactant production, haemolytic assay and cell surface hydrophobicity were performed to investigate the beneficial strain of biosurfactant-producing bacteria. Here we do share data collected from the biochemical tests to get a better understanding of the use of Serratia marcescens SA30 to degrade oil, which contributes the technical features of strengthening the biological treatment of oil-contaminated wastewater in tropical environments.

Isolation, characterization, and investigation of surface and hemolytic activities of a lipopeptide biosurfactant produced by Bacillus subtilis ATCC 6633.

Science.gov (United States)

Dehghan-Noude, Gholamreza; Housaindokht, Mohammadreza; Bazzaz, Bibi Sedigeh Fazly

2005-06-01

Bacillus subtilis ATCC 6633 was grown in BHIB medium supplemented with Mn2+ for 96 h at 37 degrees C in a shaker incubator. After removing the microbial biomass, a lipopeptide biosurfactant was extracted from the supernatant. Its structure was established by chemical and spectroscopy methods. The structure was confirmed by physical properties, such as Hydrophile-Lipophile Balance (HLB), surface activity and erythrocyte hemolytic capacity. The critical micelle concentration (cmc) and erythrocyte hemolytic capacity of the biosurfactant were compared to those of surfactants such as SDS, BC (benzalkonium chloride), TTAB (tetradecyltrimethylammonium bromide) and HTAB (hexadecyltrimethylammonium bromide). The maximum hemolytic effect for all surfactants mentioned was observed at concentrations above cmc. The maximum hemolytic effect of synthetic surfactants was more than that of the biosurfactant produced by B. subtilis ATCC 6633. Therefore, biosurfactant would be considered a suitable surface-active agent due to low toxicity to the membrane.

Sophorolipid biosurfactants: Possible uses as antibacterial and antibiofilm agent.

Science.gov (United States)

Díaz De Rienzo, Mayri A; Banat, Ibrahim M; Dolman, Ben; Winterburn, James; Martin, Peter J

2015-12-25

Biosurfactants are amphipathic, surface-active molecules of microbial origin which accumulate at interfaces reducing interfacial tension and leading to the formation of aggregated micellular structures in solution. Some biosurfactants have been reported to have antimicrobial properties, the ability to prevent adhesion and to disrupt biofilm formation. We investigated antimicrobial properties and biofilm disruption using sophorolipids at different concentrations. Growth of Gram negative Cupriavidus necator ATCC 17699 and Gram positive Bacillus subtilis BBK006 were inhibited by sophorolipids at concentrations of 5% v/v with a bactericidal effect. Sophorolipids (5% v/v) were also able to disrupt biofilms formed by single and mixed cultures of B. subtilis BBK006 and Staphylococcus aureus ATCC 9144 under static and flow conditions, as was observed by scanning electron microscopy. The results indicated that sophorolipids may be promising compounds for use in biomedical application as adjuvants to other antimicrobial against some pathogens through inhibition of growth and/or biofilm disruption. Copyright © 2015 Elsevier B.V. All rights reserved.

Effects of rhamnolipid biosurfactants on removal of phenanthrene from soil

NARCIS (Netherlands)

Noordman, Wouter H.; Ji, Wei; Brusseau, Mark L.; Janssen, Dick B.

1998-01-01

Solubilizing agents may enhance remediation of-soils contaminated with hydrophobic organic contaminants by diminishing sorption of the contaminants or increasing desorption rates. The effectiveness of rhamnolipid biosurfactants to enhance the removal of sorbed contaminants from soil was determined

Diesel degradation and biosurfactant production by Gram-positive ...

African Journals Online (AJOL)

The ability of Gram-positive bacteria to degrade diesel increased in a comparable trend as its biosurfactant production increased. The E24 index was highest at 87.6% for isolate D9. Isolates D2, D9 and D10, were identified as Paenibacillus sp. whilst isolate DJLB was found to belong to Stenotrophomonas sp. This study ...

Simultaneous valorization and biocatalytic upgrading of heavy vacuum gas oil by the biosurfactant-producing Pseudomonas aeruginosa AK6U.

Science.gov (United States)

Ismail, Wael Ahmed; Mohamed, Magdy El-Said; Awadh, Maysoon N; Obuekwe, Christian; El Nayal, Ashraf M

2017-11-01

Heavy vacuum gas oil (HVGO) is a complex and viscous hydrocarbon stream that is produced as the bottom side product from the vacuum distillation units in petroleum refineries. HVGO is conventionally treated with thermochemical process, which is costly and environmentally polluting. Here, we investigate two petroleum biotechnology applications, namely valorization and bioupgrading, as green approaches for valorization and upgrading of HVGO. The Pseudomonas aeruginosa AK6U strain grew on 20% v/v of HVGO as a sole carbon and sulfur source. It produced rhamnolipid biosurfactants in a growth-associated mode with a maximum crude biosurfactants yield of 10.1 g l -1 , which reduced the surface tension of the cell-free culture supernatant to 30.6 mN m -1 within 1 week of incubation. The rarely occurring dirhamnolipid Rha-Rha-C 12 -C 12 dominated the congeners' profile of the biosurfactants produced from HVGO. Heavy vacuum gas oil was recovered from the cultures and abiotic controls and the maltene fraction was extracted for further analysis. Fractional distillation (SimDist) of the biotreated maltene fraction showed a relative decrease in the high-boiling heavy fuel fraction (BP 426-565 °C) concomitant with increase in the lighter distillate diesel fraction (BP 315-426 °C). Analysis of the maltene fraction revealed compositional changes. The number-average (Mn) and weight-average (Mw) molecular weights, as well as the absolute number of hydrocarbons and sulfur heterocycles were higher in the biotreated maltene fraction of HVGO. These findings suggest that HVGO can be potentially exploited as a carbon-rich substrate for production of the high-value biosurfactants by P. aeruginosa AK6U and to concomitantly improve/upgrade its chemical composition. © 2017 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Formulation of a Commercial Biosurfactant for Application as a Dispersant of Petroleum and By-products Spilled in Oceans

Directory of Open Access Journals (Sweden)

Bruno Galdino Freitas

2016-10-01

Full Text Available Oil spills in oceans cause irreparable damage to marine life and harm the coastal populations of affected areas. It is therefore fundamental to develop treatment strategies for such spills. Currently, chemical dispersants have been used during oil spills, although these agents have been increasingly restricted due to their toxic potential. Thus, the aim of the present study was to formulate a biodegradable commercial biosurfactant for application as a dispersant. Biosurfactants are scientifically known biomolecules produced by microorganisms capable of allowing water-oil interaction. Thus, a biosurfactant was produced by the yeast Candida bombicola URM 3718 cultivated in industrial waste and formulated with the addition of a potassium sorbate preservative for fractionated sterilisation (tyndallisation and the combination of fluent vaporisation with the preservative. After formulation, samples were stored for 120 days, followed by surface tension, emulsification and oil dispersant tests in sea water. The results were promising for the biosurfactant formulated with the preservative, which demonstrated stability and an absence of toxicity in experiments with a marine indicator. The commercial biosurfactant was tested at different pH values, temperatures and in the presence of salt, demonstrating potential industrial application at a cost compatible with the environmental field. The formulation process developed in this research was patented in the Brazilian National Intellectual Property Institute (patent number BR1020140179631.

Investigation of Antimicrobial Activity and Statistical Optimization of Bacillus subtilis SPB1 Biosurfactant Production in Solid-State Fermentation

Directory of Open Access Journals (Sweden)

Dhouha Ghribi

2012-01-01

Full Text Available During the last years, several applications of biosurfactants with medical purposes have been reported. Biosurfactants are considered relevant molecules for applications in combating many diseases. However, their use is currently extremely limited due to their high cost in relation to that of chemical surfactants. Use of inexpensive substrates can drastically decrease its production cost. Here, twelve solid substrates were screened for the production of Bacillus subtilis SPB1 biosurfactant and the maximum yield was found with millet. A Plackett-Burman design was then used to evaluate the effects of five variables (temperature, moisture, initial pH, inoculum age, and inoculum size. Statistical analyses showed that temperature, inoculum age, and moisture content had significantly positive effect on SPB1 biosurfactant production. Their values were further optimized using a central composite design and a response surface methodology. The optimal conditions of temperature, inoculum age, and moisture content obtained under the conditions of study were 37°C, 14 h, and 88%, respectively. The evaluation of the antimicrobial activity of this compound was carried out against 11 bacteria and 8 fungi. The results demonstrated that this biosurfactant exhibited an important antimicrobial activity against microorganisms with multidrug-resistant profiles. Its activity was very effective against Staphylococcus aureus, Staphylococcus xylosus, Enterococcus faecalis, Klebsiella pneumonia, and so forth.

Physiological and Molecular Characterization of Biosurfactant Producing Endophytic Fungi Xylaria regalis from the Cones of Thuja plicata as a Potent Plant Growth Promoter with Its Potential Application

Directory of Open Access Journals (Sweden)

Mohd Adnan

2018-01-01

Full Text Available Currently, there is an absolute concern for all nations in agricultural productivity to meet growing demands of human population. In recent time, biosurfactants produced by diverse group of microorganisms are used to achieve such demands as it is known for its ecofriendly use in elimination of plant pathogens and for increasing the bioavailability of nutrients for plants. Endophytic fungi are the important source of secondary metabolites and novel bioactive compounds for different biological applications. In the present study, endophytic fungi Xylaria regalis (X. regalis recovered from the cones of Thuja plicata was evaluated for its biosurfactant producing ability and plant growth-promoting abilities through various screening methods and also via its antagonistic activity against phytopathogens like Fusarium oxysporum and Aspergillus niger. In addition, X. regalis was also tested in vivo for a various range of growth parameters in chilli under greenhouse conditions. Significant increase in shoot and root length, dry matter production of shoot and root, chlorophyll, nitrogen, and phosphorus contents of chilli seedlings was found, which reveals its ability to improve the growth of crop plants. Hence, this study suggests the possibility of biosurfactant producing endophytic fungi X. regalis as a source of novel green biosurfactant for sustainable agriculture to achieve growing demands.

Production, characterization, and antifungal activity of a biosurfactant produced by Rhodotorula babjevae YS3.

Science.gov (United States)

Sen, Suparna; Borah, Siddhartha Narayan; Bora, Arijit; Deka, Suresh

2017-05-30

Sophorolipids are one of the most promising glycolipid biosurfactants and have been successfully employed in bioremediation and various other industrial sectors. They have also been described to exhibit antimicrobial activity against different bacterial species. Nevertheless, previous literature pertaining to the antifungal activity of sophorolipids are limited indicating the need for further research to explore novel strains with wide antimicrobial activity. A novel yeast strain, Rhodotorula babjevae YS3, was recently isolated from an agricultural field in Assam, Northeast India. This study was primarily emphasized at the characterization and subsequent evaluation of antifungal activity of the sophorolipid biosurfactant produced by R. babjevae YS3. The growth kinetics and biosurfactant production by R. babjevae YS3 was evaluated by cultivation in Bushnell-Haas medium containing glucose (10% w/v) as the sole carbon source. A reduction in the surface tension of the culture medium from 70 to 32.6 mN/m was observed after 24 h. The yield of crude biosurfactant was recorded to be 19.0 g/l which might further increase after optimization of the growth parameters. The biosurfactant was characterized to be a heterogeneous sophorolipid (SL) with both lactonic and acidic forms after TLC, FTIR and LC-MS analyses. The SL exhibited excellent oil spreading and emulsifying activity against crude oil at 38.46 mm 2 and 100% respectively. The CMC was observed to be 130 mg/l. The stability of the SL was evaluated over a wide range of pH (2-10), salinity (2-10% NaCl) and temperature (at 120 °C for time intervals of 30 up to 120 min). The SL was found to retain surface-active properties under the extreme conditions. Additionally, the SL exhibited promising antifungal activity against a considerably broad group of pathogenic fungi viz. Colletotrichum gloeosporioides, Fusarium verticilliodes, Fusarium oxysporum f. sp. pisi, Corynespora cassiicola, and Trichophyton rubrum. The

Biosurfactants in cosmetics and biopharmaceuticals.

Science.gov (United States)

Varvaresou, A; Iakovou, K

2015-09-01

Biosurfactants are surface-active biomolecules that are produced by various micro-organisms. They show unique properties i.e. lower toxicity, higher biodegradability and environmental compatibility compared to their chemical counterparts. Glycolipids and lipopeptides have prompted application in biotechnology and cosmetics due to their multi-functional profile i.e. detergency, emulsifying, foaming and skin hydrating properties. Additionally, some of them can be served as antimicrobials. In this study the current status of research and development on rhamnolipids, sophorolipids, mannosyloerythritol lipids, trehalipids, xylolipids and lipopeptides particularly their commercial application in cosmetics and biopharmaceuticals, is described. © 2015 The Society for Applied Microbiology.

Production and characterization of rhamnolipid biosurfactant from waste frying coconut oil using a novel Pseudomonas aeruginosa D.

Science.gov (United States)

George, S; Jayachandran, K

2013-02-01

To improve biosurfactant production economics by the utilization of potential low-cost materials. In an attempt to utilize cost-effective carbon sources in the fermentative production of biosurfactants, various pure and waste frying oils were screened by a standard biosurfactant producing strain. Considering the regional significance, easy availability and the economical advantages, waste frying coconut oil was selected as the substrate for further studies. On isolation of more competent strains that could use waste frying coconut oil efficiently as a carbon source, six bacterial strains were isolated on cetyltrimethyl ammonium bromide-methylene blue agar plate, from a soil sample collected from the premises of a coconut oil mill. Among these, Pseudomonas aeruginosa D was selected as the potential producer of rhamnolipid. Spectrophotometric method, TLC, methylene blue active substance assay, drop collapse technique, surface tension measurement by Du Nouy ring method and emulsifying test confirmed the rhamnolipid producing ability of the selected strain and various process parameters were optimized for the production of maximum amount of biosurfactant. Rhamnolipid components purified and separated by ethyl acetate extraction, preparative silica gel column chromatography, HPLC and TLC were characterized by fast atom bombardment mass spectrometry as a mixture of dirhamnolipids and monorhamnolipids. The rhamnolipid homologues detected were Rha-Rha-C(10) -C(10) , Rha-C(12) -C(10) and Rha-C(10) -C(8) /Rha-C(8) -C(10) . These results indicated the possibility of waste frying coconut oil to be used as a very effective alternate substrate for the economic production of rhamnolipid by a newly isolated Ps. aeruginosa D. Results of this study throws light on the alternate use of already used cooking oil as high-energy source for producing a high value product like rhamnolipid. This would provide options for the food industry other than the recycling and reuse of waste frying

Biosurfactants produced by Microbacterium sp., isolated from aquatic macrophytes in hydrocarbon-contaminated area in the Rio Negro, Manaus, Amazonas

Directory of Open Access Journals (Sweden)

João Marcelo Silva Lima

2017-05-01

Full Text Available Endophytic bacteria isolated from Eichhornia crassipes (Mart Solms., collected in oil contaminated wastewater of effluent generated by Petrobras refinery in Manaus were investigated to determine their potential for producing biosurfactants. Assay with 2.6-dichlorophenol indophenol (DCPIP indicator to verify hydrocarbon biodegradation activity; oil emulsification test; drop-collapse method; surface tension and growth curve of biosurfactant production. The M87 Microbacterium sp. strain chosen for this work was identified by the sequencing of the rDNA region and the chemical characterization was performed by FTIR, UFLC/MS and 1H RMN techniques. The selected bacterial isolate provided 3g L-1 of biosurfactant, using diesel oil as sole carbon source, being efficient in biodegrading oil as demonstrated by the DCPIP test. Fractions obtained by column chromatography were efficient in reducing water surface tension around 40 mN m-1, especially fraction 1, which reduced it to 34.17 mN m-1. The different techniques of chemical analysis used for the identification of the biosurfactant isolate indicated that this is probably a long - chain fatty acid lipid type, which may be used in the future as both biosurfactant in decontamination processes of hydrocarbon-polluted areas or as bioemulsifier in countless processes, since it exhibited no toxicity as determined by Alamar Blue assay.

Optimization of crude oil degradation by Dietzia cinnamea KA1, capable of biosurfactant production.

Science.gov (United States)

Kavynifard, Amirarsalan; Ebrahimipour, Gholamhossein; Ghasempour, Alireza

2016-05-01

The aim of this study was isolation and characterization of a crude oil degrader and biosurfactant-producing bacterium, along with optimization of conditions for crude oil degradation. Among 11 isolates, 5 were able to emulsify crude oil in Minimal Salt Medium (MSM) among which one isolate, named KA1, showed the highest potency for growth rate and biodegradation. The isolate was identified as Dietzia cinnamea KA1 using morphological and biochemical characteristics and 16S rRNA gene sequencing. The optimal conditions were 510 mM NaCl, pH 9.0, 35 °C, and minimal requirement of 46.5 mM NH4 Cl and 2.10 mM NaH2 PO4 . Gravimetric test and Gas chromatography-Mass spectroscopy technique (GC-MS) showed that Dietzia cinnamea KA1 was able to utilize and degrade 95.7% of the crude oil after 5 days, under the optimal conditions. The isolate was able to grow and produce biosurfactant when cultured in MSM supplemented with crude oil, glycerol or whey as the sole carbon sources, but bacterial growth was occurred using molasses with no biosurfactant production. This is the first report of biosurfactant production by D. cinnamea using crude oil, glycerol and whey and the first study to report a species of Dietzia degrading a wide range of hydrocarbons in a short time. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Application of biosurfactants, rhamnolipid, and surfactin, for enhanced biodegradation of diesel-contaminated water and soil.

Science.gov (United States)

Whang, Liang-Ming; Liu, Pao-Wen G; Ma, Chih-Chung; Cheng, Sheng-Shung

2008-02-28

This study investigated potential application of two biosurfactants, surfactin (SF) and rhamnolipid (RL), for enhanced biodegradation of diesel-contaminated water and soil with a series of bench-scale experiments. The rhamnolipid used in this study, a commonly isolated glycolipid biosurfactant, was produced by Pseudomonas aeruginosa J4, while the surfactin, a lipoprotein type biosurfactant, was produced by Bacillus subtilis ATCC 21332. Both biosurfactants were able to reduce surface tension to less than 30 dynes/cm from 72 dynes/cm with critical micelle concentration (CMC) values of 45 and 50 mg/L for surfactin and rhamnolipid, respectively. In addition, the results of diesel dissolution experiments also demonstrated their ability in increasing diesel solubility with increased biosurfactant addition. In diesel/water batch experiments, an addition of 40 mg/L of surfactin significantly enhanced biomass growth (2500 mg VSS/L) as well as increased diesel biodegradation percentage (94%), compared to batch experiments with no surfactin addition (1000 mg VSS/L and 40% biodegradation percentage). Addition of surfactin more than 40 mg/L, however, decreased both biomass growth and diesel biodegradation efficiency, with a worse diesel biodegradation percentage (0%) at 400 mg/L of SF addition. Similar trends were also observed for both specific rate constants of biomass growth and diesel degradation, as surfactin addition increased from 0 to 400 mg/L. Addition of rhamnolipid to diesel/water systems from 0 to 80 mg/L substantially increased biomass growth and diesel biodegradation percentage from 1000 to 2500 mg VSS/L and 40 to 100%, respectively. Rhamnolipid addition at a concentration of 160 mg/L provided similar results to those of an 80 mg/L addition. Finally, potential application of surfactin and rhamnolipid in stimulating indigenous microorganisms for enhanced bioremediation of diesel-contaminated soil was also examined. The results confirmed their enhancing capability

Exploiting the aerobic endospore-forming bacterial diversity in saline and hypersaline environments for biosurfactant production.

Science.gov (United States)

de Almeida Couto, Camila Rattes; Alvarez, Vanessa Marques; Marques, Joana Montezano; de Azevedo Jurelevicius, Diogo; Seldin, Lucy

2015-10-28

Biosurfactants are surface-active biomolecules with great applicability in the food, pharmaceutical and oil industries. Endospore-forming bacteria, which survive for long periods in harsh environments, are described as biosurfactant producers. Although the ubiquity of endospore-forming bacteria in saline and hypersaline environments is well known, studies on the diversity of the endospore-forming and biosurfactant-producing bacterial genera/species in these habitats are underrepresented. In this study, the structure of endospore-forming bacterial communities in sediment/mud samples from Vermelha Lagoon, Massambaba, Dois Rios and Abraão Beaches (saline environments), as well as the Praia Seca salterns (hypersaline environments) was determined via denaturing gradient gel electrophoresis. Bacterial strains were isolated from these environmental samples and further identified using 16S rRNA gene sequencing. Strains presenting emulsification values higher than 30 % were grouped via BOX-PCR, and the culture supernatants of representative strains were subjected to high temperatures and to the presence of up to 20 % NaCl to test their emulsifying activities in these extreme conditions. Mass spectrometry analysis was used to demonstrate the presence of surfactin. A diverse endospore-forming bacterial community was observed in all environments. The 110 bacterial strains isolated from these environmental samples were molecularly identified as belonging to the genera Bacillus, Thalassobacillus, Halobacillus, Paenibacillus, Fictibacillus and Paenisporosarcina. Fifty-two strains showed emulsification values of at least 30%, and they were grouped into 18 BOX groups. The stability of the emulsification values varied when the culture supernatants of representative strains were subjected to high temperatures and to the presence of up to 20% NaCl. The presence of surfactin was demonstrated in one of the most promising strains. The environments studied can harbor endospore

Yeast glycolipid biosurfactants.

Science.gov (United States)

Jezierska, Sylwia; Claus, Silke; Van Bogaert, Inge

2017-10-25

Various yeasts, both conventional and exotic ones, are known to produce compounds useful to mankind. Ethanol is the most known of these compounds, but more complex molecules such as amphiphilic biosurfactants can also be derived from eukaryotic microorganisms at an industrially and commercially relevant scale. Among them, glycolipids are the most promising, due to their attractive properties and high product titers. Many of these compounds can be considered as secondary metabolites with a specific function for the host. Hence, a dedicated biosynthetic process enables regulation and combines pathways delivering the lipidic moiety and the hydrophilic carbohydrate part of the glycolipid. In this Review, we will discuss the biosynthetic and regulatory aspects of the yeast-derived sophorolipids, mannosylerythritol lipids, and cellobiose lipids, with special emphasis on the relation between glycolipid synthesis and the general lipid metabolism. © 2017 Federation of European Biochemical Societies.

Evaluation of emulsifier stability of biosurfactant produced by Saccharomyces lipolytica CCT-0913

Directory of Open Access Journals (Sweden)

Álvaro Silva Lima

2009-04-01

Full Text Available Surface-active compounds of biological origin are widely used for many industries (cosmetic, food, petrochemical. The Saccharomyces lipolytica CCT-0913 was able to grow and produce a biosurfactant on 5% (v/v diesel-oil at pH 5.0 and 32ºC. The cell-free broth emulsified and stabilized the oil-in-water emulsion through a first order kinetics. The results showed that the initial pH value and temperature influenced the emulsifier stability (ES, which was the time when oil was separated. The biosurfactant presented different stabilization properties for vegetable and mineral oil in water solution, despite the highest values of the ES occurring with vegetable oil. The biosurfactant presented smallest ES when compared to commercial surfactants; however, this biosurfactant was not purified.Os tensoativos de origem biológica são amplamente utilizados em diversas aplicações. O microrganismo Saccharomyces lipolytica CCT-0913 possui a habilidade de crescer em 5% (v/v óleo diesel a pH 5,0 e 32ºC e produzir biosurfactante. O caldo fermentado livre de células e produzido por S. lipolytica emulsiona e estabiliza emulsões óleo em água de acordo com uma cinética de primeira ordem. Os resultados mostram que o valor do pH inicial e a temperatura influenciam a estabilidade emulsificante (ES, que é medido pelo tempo que a quantidade de óleo. O biosurfactante apresenta diferentes valores de estabilidade emulsificante para óleos vegetais e minerais em emulsões óleo-água, os maiores valores de ES ocorrem nas emulsões utilizando óleo vegetal. O biosurfactante apresenta valores baixos de ES quando comparado com emulsificantes comerciais, entretanto sem sofrer nenhum processo de purificação.

Application of the biosurfactants produced by Bacillus spp. (SH 20 ...

African Journals Online (AJOL)

Application of the biosurfactants produced by Bacillus spp. (SH 20 and SH 26) and P. aeruginosa SH 29 isolated from the rhizosphere soil of an Egyptian salt marsh plant for the cleaning of oil - contaminataed vessels and enhancing the biodegradat.

Avaliação cinética da produção de biossurfactantes bacterianos Bacteria biosurfactants production kinetic evaluation

Directory of Open Access Journals (Sweden)

Marta Heidtmann Pinto

2009-01-01

Full Text Available Biosurfactants present advantages in relation to the synthetic surfactants, as the biodegradability and low toxicity, and can be applied in the food industry, in pharmaceutical products, cosmetics and in the petroleum recovery. This paper aimed at selecting bacteria for biosurfactant production, evaluating the surface tension and the emulsifying activity and studying the fermentation process kinetics. The pure culture of Corynebacterium aquaticum showed capacity to promote emulsions formation and presented the smallest surface tension (28.8 mN m-1, and, in general, larger kinetic parameters, being selected as biosurfactant producer.

Isolation and characterization of a novel biosurfactant produced by hydrocarbon-degrading bacterium Alcanivorax dieselolei B-5.

Science.gov (United States)

Qiao, N; Shao, Z

2010-04-01

Our goal was to identify a novel biosurfactant produced by a marine oil-degrading bacterium. Biosurfactants were produced by Alcanivorax dieselolei strain B-5(T) growing with diesel oil as the sole carbon and energy source. Culture supernatant was first extracted with chloroform/methanol (1:1, v/v), then further purified step by step with a normal phase silica gel column, a Sephadex LH20 gel column and a preparative thin layer plate. The main component was determined to be a lipopeptide; it was chemically characterized with nuclear magnetic resonance, liquid chromatography-quadrupole ion-trap mass spectrometry, amino acid analysis and GC-MS and was found to be a mixture of proline lipids. The monomers of the proline lipids were composed of a proline residue and a fatty acid (C(14:0), C(16:0) or C(18:0)). The critical micelle concentration of the mixed proline lipids was determined to be 40 mg l(-1). Moreover, activity variations in ranges of pH, temperature and salinity were also detected and showed reasonable stability. Alcanivorax dieselolei B-5 produced a novel linear lipoamino biosurfactant, characterized as a proline lipid. A proline lipid was characterized for the first time as a bacterial biosurfactant. This product has potential in both environmental and industrial applications.

Isolation and screening of glycolipid biosurfactant producers from sugarcane.

Science.gov (United States)

Morita, Tomotake; Fukuoka, Tokuma; Imura, Tomohiro; Hirose, Naoto; Kitamoto, Dai

2012-01-01

Forty-three fungal producers for glycolipid biosurfactants, mannosylerythritol lipids (MELs), were isolated from leaves and smuts of sugarcane plants. These isolates produced MELs with sugarcane juice as nutrient source. The strains were taxonomically categorized into the genera Pseudozyma and Ustilago on the basis of partial sequences of the ribosomal RNA gene.

Production of a Lipopeptide Biosurfactant by a Novel Bacillus sp. and Its Applicability to Enhanced Oil Recovery.

Science.gov (United States)

Varadavenkatesan, Thivaharan; Murty, Vytla Ramachandra

2013-01-01

Biosurfactants are surface-active compounds derived from varied microbial sources including bacteria and fungi. They are secreted extracellularly and have a wide range of exciting properties for bioremediation purposes. They also have vast applications in the food and medicine industry. With an objective of isolating microorganisms for enhanced oil recovery (EOR) operations, the study involved screening of organisms from an oil-contaminated site. Morphological, biochemical, and 16S rRNA analysis of the most promising candidate revealed it to be Bacillus siamensis, which has been associated with biosurfactant production, for the first time. Initial fermentation studies using mineral salt medium supplemented with crude oil resulted in a maximum biosurfactant yield of 0.64 g/L and reduction of surface tension to 36.1 mN/m at 96 h. Characterization studies were done using thin layer chromatography and Fourier transform infrared spectroscopy. FTIR spectra indicated the presence of carbonyl groups, alkyl bonds, and C-H and N-H stretching vibrations, typical of peptides. The extracted biosurfactant was stable at extreme temperatures, pH, and salinity. Its applicability to EOR was further verified by conducting sand pack column studies that yielded up to 60% oil recovery.

Physicochemical and biochemical characterization of biosurfactants released by Lactobacillus strains

NARCIS (Netherlands)

Velraeds, MMC; vanderMei, HC; Reid, G; Busscher, HJ

1996-01-01

Biosurfactants from Lactobacillus casei subsp. rhamnosus 36 and ATCC 7469, Lactobacillus fermentum B54 and Lactobacillus acidophilus RC14 were isolated from bacteria in their mid-exponential (4-5 h) and stationary growth phases (18 h) and physicochemical and biochemical properties of the

Biosurfactant-assisted phytoremediation of multi-contaminated industrial soil using sunflower (Helianthus annuus L.).

Science.gov (United States)

Liduino, Vitor S; Servulo, Eliana F C; Oliveira, Fernando J S

2018-02-01

This study evaluated the use of commercial rhamnolipid biosurfactant supplementation in the phytoremediation of a soil via sunflower (Helianthus annuus L.) cultivation. The soil, obtained from an industrial area, was co-contaminated with heavy metals and petroleum hydrocarbons. The remediation tests were monitored for 90 days. The best results for removal of contaminants were obtained from the tests in which the sunflower plants were cultivated in soil with 4 mg kg -1 of the rhamnolipid. Under these conditions, reductions of 58% and 48% were obtained in the total petroleum hydrocarbon (TPH) and polycyclic aromatic hydrocarbon (PAH) concentrations, respectively; reductions in the concentrations of the following metals were also achieved: Ni (41%), Cr (30%), Pb (29%), and Zn (20%). The PCR-DGGE analysis of soil samples collected before and after the treatments verified that the plant cultivation and biosurfactants supplementation had little effect on the structure of the dominant bacterial community in the soil. The results indicated that sunflower cultivation with the addition of a biosurfactant is a viable and efficient technology to treat soils co-contaminated with heavy metals and petroleum hydrocarbons.

Characterization of biosurfactants produced by novel strains of Ochrobactrum anthropi HM-1 and Citrobacter freundii HM-2 from used engine oil-contaminated soil

Directory of Open Access Journals (Sweden)

Haytham M.M. Ibrahim

2018-03-01

Full Text Available Microbial surfactants are widely used for industrial, agricultural, food, cosmetics, pharmaceutical, and medical applications. In this study, two bacterial strains namely, Ochrobactrum anthropi HM-1 and Citrobacter freundii HM-2, previously isolated from used engine oil contaminated soil, and capable of producing biosurfactants, were used. Their cell-free culture broth showed positive results toward five screening tests (hemolysis in blood agar, drop collapse, oil displacement, emulsification activity (E24, and surface tension (ST reduction. They reduced the ST of growth medium (70 ± 0.9 to 30.8 ± 0.6 and 32.5 ± 1.3 mN/m, respectively. The biosurfactants were classified as anionic biomolecules. Based on TLC pattern and FT-IR analysis, they were designated as glycolipids (rhamnolipid. Waste frying oil was feasibly used as a cheap and dominant carbon source for biosurfactants production; 4.9 and 4.1 g/l were obtained after 96 h of incubation, respectively. Compared with non-irradiated cells, gamma-irradiated cells (1.5 kGy revealed enhanced biosurfactant production by 56 and 49% for HM-1 and HM-2, respectively. The biosurfactants showed good stability after exposure to extreme conditions [temperatures (50–100 °C for 30 min, pH (2–12 and salinity (2–10% NaCl], they retained 83 and 79.3% of their E24, respectively, after incubation for a month, under extreme conditions. Biosurfactants effectively recovered up to 70 and 67% of the residual oil, respectively, from oil-saturated sand pack columns. These biosurfactants are an interesting biotechnological product for many environmental and industrial applications. Keywords: Ochrobactrum anthropi, Citrobacter freundii, Biosurfactant, Characterization, Stability

Biosurfactant production by yeasts isolated from hydrocarbon polluted environments.

Science.gov (United States)

Kaur, Kamalpreet; Sangwan, Seema; Kaur, Harpreet

2017-11-03

Thirty-two yeast isolates were retrieved from four soil samples collected from hydrocarbon-polluted locations of Hisar, Haryana, using enrichment culture technique with 1% (v/v) diesel as carbon source. Total nine isolates showing blood agar haemolysis were screened further for biosurfactant production. Yeast isolate, YK32, gave highest 8.4-cm oil displacement which was found to be significantly higher as compared to positive control, 0.2% (w/v) SDS (6.6 cm), followed by 6.2 and 6.0 cm by isolates YK20 and YK21, respectively. Maximum emulsification index was obtained in case of isolates YK20 and YK21 measuring 53.8%, after 6 days of incubation utilizing glucose as carbon source, whereas isolate YK32 was found to be reducing surface tension up to 93 dynes/cm and presented 99.6% degree of hydrophobicity. Olive oil has supported maximum surface tension reduction in isolates YK32 and YK21 equivalent to 53 and 48 dynes/cm and gave 88.3 and 88.5% degree of hydrophobicity, respectively. Diesel was not preferred as carbon source by most of the isolates except YK28 which generated 5.5-cm oil displacement, 25% emulsification index, reduced surface tension to the level of 38 dynes/cm and presented 89% degree of hydrophobicity. Conclusively, isolates YK20, YK21, YK22 and YK32 were marked as promising biosurfactant producers and were subjected to identification. Based on microscopic examination and biochemical peculiarities, isolates YK21 and YK22 might be identified as Candida spp., whereas, isolates YK20 and YK32 might be identified as Saccharomycopsis spp. and Brettanomyces spp., respectively. Interestingly it is the first report indicating Saccharomycopsis spp. and Brettanomyces spp. as a potential biosurfactant producer.

Biosurfactant production from marine hydrocarbon-degrading consortia and pure bacterial strains using crude oil as carbon source

OpenAIRE

Antoniou, Eleftheria; Fodelianakis, Stilianos; Korkakaki, Emmanouela; Kalogerakis, Nicolas

2015-01-01

Biosurfactants (BS) are green amphiphilic molecules produced by microorganisms during biodegradation, increasing the bioavailability of organic pollutants. In this work, the BS production yield of marine hydrocarbon degraders isolated from Elefsina bay in Eastern Mediterranean Sea has been investigated. The drop collapse test was used as a preliminary screening test to confirm biosurfactant producing strains or mixed consortia. The community structure of the best consortia based on the drop c...

Kinetic study and modeling of biosurfactant production using Bacillus sp.

Directory of Open Access Journals (Sweden)

Hesty Heryani

2017-05-01

Conclusions: For further development and industrial applications, the modified Gompertz equation is proposed to predict the cell mass and biosurfactant production as a goodness of fit was obtained with this model. The modified Gompertz equation was also extended to enable the excellent prediction of the surface tension.

Isolation and characterization of biosurfactant-producing Alcanivorax strains: hydrocarbon accession strategies and alkane hydroxylase gene analysis.

Science.gov (United States)

Olivera, Nelda L; Nievas, Marina L; Lozada, Mariana; Del Prado, Guillermo; Dionisi, Hebe M; Siñeriz, Faustino

2009-01-01

Biosurfactant-producing bacteria belonging to the genera Alcanivorax, Cobetia and Halomonas were isolated from marine sediments with a history of hydrocarbon exposure (Aristizábal and Gravina Peninsulas, Argentina). Two Alcanivorax isolates were found to form naturally occurring consortia with strains closely related to Pseudomonas putida and Microbacterium esteraromaticum. Alkane hydroxylase gene analysis in these two Alcanivorax strains resulted in the identification of two novel alkB genes, showing 86% and 60% deduced amino acid sequence identity with those of Alcanivorax sp. A-11-3 and Alcanivorax dieselolei P40, respectively. In addition, a gene homologous to alkB2 from Alcanivorax borkumensis was present in one of the strains. The consortium formed by this strain, Alcanivorax sp. PA2 (98.9% 16S rRNA gene sequence identity with A. borkumensis SK2(T)) and P. putida PA1 was characterized in detail. These strains form cell aggregates when growing as mixed culture, though only PA2 was responsible for biosurfactant activity. During exponential growth phase of PA2, cells showed high hydrophobicity and adherence to hydrocarbon droplets. Biosurfactant production was only detectable at late growth and stationary phases, suggesting that it is not involved in initiating oil degradation and that direct interfacial adhesion is the main hydrocarbon accession mode of PA2. This strain could be useful for biotechnological applications due to its biosurfactant production, catabolic and aggregation properties.

Involvement of phenazines and biosurfactants in biocontrol of Pythium myriotylum root rot on cocoyam by Pseudomonas sp. CMR12A

Science.gov (United States)

Pseudomonas sp. CMR12a was isolated from the rhizosphere of the tropical tuber crop cocoyam and produces both phenazines and cyclic lipopeptide (CLP) biosurfactants. CMR12a was shown to be an efficient biocontrol agent of P. myriotylum on cocoyam. To assess the importance of phenazine and biosurfact...

Production and characterization of microbial biosurfactants for potential use in oil-spill remediation.

Science.gov (United States)

Marti, M E; Colonna, W J; Patra, P; Zhang, H; Green, C; Reznik, G; Pynn, M; Jarrell, K; Nyman, J A; Somasundaran, P; Glatz, C E; Lamsal, B P

2014-02-05

Two biosurfactants, surfactin and fatty acyl-glutamate, were produced from genetically-modified strains of Bacillus subtilis on 2% glucose and mineral salts media in shake-flasks and bioreactors. Biosurfactant synthesis ceased when the main carbohydrate source was completely depleted. Surfactin titers were ∼30-fold higher than fatty acyl-glutamate in the same medium. When bacteria were grown in large aerated bioreactors, biosurfactants mostly partitioned to the foam fraction, which was recovered. Dispersion effectiveness of surfactin and fatty acyl-glutamate was evaluated by measuring the critical micelle concentration (CMC) and dispersant-to-oil ratio (DOR). The CMC values for surfactin and fatty acyl-glutamate in double deionized distilled water were 0.015 and 0.10 g/L, respectively. However, CMC values were higher, 0.02 and 0.4 g/L for surfactin and fatty acyl-glutamate, respectively, in 12 parts per thousand Instant Ocean®[corrected].sea salt, which has been partly attributed to saline-induced conformational changes in the solvated ionic species of the biosurfactants. The DORs for surfactin and fatty acyl-glutamate were 1:96 and 1:12, respectively, in water. In Instant Ocean® solutions containing 12 ppt sea salt, these decreased to 1:30 and 1:4, respectively, suggesting reduction in oil dispersing efficiency of both surfactants in saline. Surfactant toxicities were assessed using the Gulf killifish, Fundulus grandis, which is common in estuarine habitats of the Gulf of Mexico. Surfactin was 10-fold more toxic than fatty acyl-glutamate. A commercial surfactant, sodium laurel sulfate, had intermediate toxicity. Raising the salinity from 5 to 25 ppt increased the toxicity of all three surfactants; however, the increase was the lowest for fatty acyl-glutamate. Copyright © 2013 Elsevier Inc. All rights reserved.

Improving ADM1 model to simulate anaerobic digestion start-up with inhibition phase based on cattle slurry

International Nuclear Information System (INIS)

Normak, A.; Suurpere, J.; Suitso, I.; Jõgi, E.; Kokin, E.; Pitk, P.

2015-01-01

The Anaerobic Digestion Model No.1 (ADM1) was improved to simulate an anaerobic digestion start-up phase. To improve the ADM1, a combined hydrolysis equation was used based on the Contois model of bacterial growth and the function of hydrolysis inhibition by VFA. The start-up with fresh cattle slurry was carried out in a pilot-scale reactor to calibrate the chosen parameters of the ADM1. The important aspects of model calibration were hydrolysis rate, the number of anaerobic microbes in cattle slurry, and the growth rate of bacteria. Good simulation results were achieved after calibration for the independent start-up test with pre-conditioned cattle slurry. - Highlights: • Improved ADM1 can be used for simulation of reactor start-up with inhibition phase. • The hydrolysis rate had a decreased value in case of high VFA concentration or low number of hydrolytic bacteria. • Hydrolysis inhibitory threshold value of 9.85 g L −1 was obtained for VFA. • Start-up with pre-conditioned cattle slurry had a relatively short inhibition phase

Ultrasound pre-treatment for anaerobic digestion improvement.

Science.gov (United States)

Pérez-Elvira, S; Fdz-Polanco, M; Plaza, F I; Garralón, G; Fdz-Polanco, F

2009-01-01

Prior research indicates that ultrasounds can be used in batch reactors as pre-treatment before anaerobic digestion, but the specific energy required at laboratory-scale is too high. This work evaluates both the continuous ultrasound device performance (efficiency and solubilisation) and the operation of anaerobic digesters continuously fed with sonicated sludge, and presents energy balance considerations. The results of sludge solubilisation after the sonication treatment indicate that, applying identical specific energy, it is better to increase the power than the residence time. Working with secondary sludge, batch biodegradability tests show that by applying 30 kWh/m3 of sludge, it is possible to increase biogas production by 42%. Data from continuous pilot-scale anaerobic reactors (V=100 L) indicate that operating with a conventional HRT=20 d, a reactor fed with pre-treated sludge increases the volatile solids removal and the biogas production by 25 and 37% respectively. Operating with HRT=15 d, the removal efficiency is similar to the obtained with a reactor fed with non-hydrolysed sludge at HTR=20 d, although the specific biogas productivity per volume of reactor is higher for the pretreated sludge. Regarding the energy balance, although for laboratory-scale devices it is negative, full-scale suppliers state a net generation of 3-10 kW per kW of energy used.

Combination of bioleaching by gross bacterial biosurfactants and flocculation: A potential remediation for the heavy metal contaminated soils.

Science.gov (United States)

Yang, Zhihui; Shi, Wei; Yang, Weichun; Liang, Lifen; Yao, Wenbin; Chai, Liyuan; Gao, Shikang; Liao, Qi

2018-09-01

Combining bioleaching by the gross biosurfactants of Burkholderia sp. Z-90 and flocculation by poly aluminium chloride (PAC) was proposed to develop a potential environment-friendly and cost-effective technique to remediate the severely contaminated soils by heavy metals. The factors affecting soil bioleaching by the gross biosurfactants of Burkholderia sp. Z-90 were optimized. The results showed the optimal removing efficiencies of Zn, Pb, Mn, Cd, Cu, and As by the Burkholderia sp. Z-90 leachate were 44.0, 32.5, 52.2, 37.7, 24.1 and 31.6%, respectively at soil liquid ratio of 1:20 (w/v) for 5 d, which were more efficient than that by 0.1% of rhamnolipid. The amounts of the bioleached heavy metals by the Burkholderia sp. Z-90 leachate were higher than that by other biosurfactants in the previous studies, although the removal efficiencies of the metals by the leachate were relatively lower. It was suggested that more heavy metals caused more competitive to chelate with function groups of the gross biosurfactants and the metal removal efficiencies by biosurfactants in natural soils were lower than in the artificially contaminated soils. Moreover, the Burkholderia sp. Z-90 leachate facilitated the metals to be transformed to the easily migrating speciation fractions. Additional, the results showed that PAC was efficient in the following flocculation to remove heavy metals in the waste bio-leachates. Our study will provide support for developing a bioleaching technique model to remediate the soils extremely contaminated by heavy metals. Copyright © 2018 Elsevier Ltd. All rights reserved.

Production, Structural Elucidation, and In Vitro Antitumor Activity of Trehalose Lipid Biosurfactant from Nocardia farcinica Strain.

Science.gov (United States)

Christova, Nelly; Lang, Siegmund; Wray, Victor; Kaloyanov, Kaloyan; Konstantinov, Spiro; Stoineva, Ivanka

2015-04-01

The objective of this study was to isolate and identify the chemical structure of a biosurfactant produced by Nocardia farcinica strain BN26 isolated from soil, and evaluate its in vitro antitumor activity on a panel of human cancer cell lines. Strain BN26 was found to produce glycolipid biosurfactant on n-hexadecane as the sole carbon source. The biosurfactant was purified using medium-pressure liquid chromatography and characterized as trehalose lipid tetraester (THL) by nuclear magnetic resonance spectroscopy and mass spectrometry. Subsequently, the cytotoxic effects of THL on cancer cell lines BV-173, KE-37 (SKW-3), HL-60, HL-60/DOX, and JMSU-1 were evaluated by MTT assay. It was shown that THL exerted concentration-dependent antiproliferative activity against the human tumor cell lines and mediated cell death by the induction of partial oligonucleosomal DNA fragmentation. These findings suggest that THL could be of potential to apply in biomedicine as a therapeutic agent.

Diversity of biosurfactant producing microorganisms isolated from soils contaminated with diesel oil.

Science.gov (United States)

Menezes Bento, Fátima; de Oliveira Camargo, Flavio A; Okeke, Benedict C; Frankenberger, William T

2005-01-01

Biosurfactant production is a desirable property of hydrocarbon-degrading microorganisms (HDM). We characterized biosurfactant producing microbial populations from a Long Beach soil, California (USA) and a Hong Kong soil (China), contaminated with diesel oil. A total of 33 hydrocarbon-utilizing microorganisms were isolated from the soils. Twelve isolates and three defined consortia were tested for biosurfactant production and emulsification activity. The highest reduction of surface tension was achieved with a consortium of L1, L2 and L3 isolates from a Long Beach soil (41.4mN m(-1)). Isolate L1 (Acinetobacter junii) displayed the highest reduction of surface tension (46.5 mN m(-1)). The emulsifying capacity evaluated by the E24 emulsification index was highest in the culture of isolate L5 (74%). No substantial emulsification was achieved with the cell-free extracts, indicating that the emulsifying activity was not extracellular. Based on surface tension and the E24 index results, isolates F1, F2, F3, F4, L1, L2, L3 and L4 were identified by 16S rRNA gene sequencing as Bacillus cereus, Bacillus sphaericus, B. fusiformis, Acinetobacter junii, a non-cultured bacterium, Pseudomonas sp. and B. pumilus, respectively. Cluster analyses of 16S rRNA gene sequences of the bacterial isolates revealed 70% similarity amongst hydrocarbon-degrading bacterial community present in both soils. Five isolates (isolates F1, F2, F3, F4 and L4) belong to the Firmicutes order, two isolates (L1 and L3) belong to the Proteobacteria order and one isolate (L2) is an Actinomyces sp. Simpson's index (1 - D) and the Shannon-Weaver index (H) revealed more diversity of HDM in the Hong Kong soil, while evenness (E) and the equitability (J) data indicated that there was not a dominant population. Bacterial isolates displaying substantial potential for production of biosurfactants can be applied in the bioremediation of soils contaminated with petroleum hydrocarbons.

Investigation of the release of PAHs from artificially contaminated sediments using cyclolipopeptidic biosurfactants.

Science.gov (United States)

Portet-Koltalo, F; Ammami, M T; Benamar, A; Wang, H; Le Derf, F; Duclairoir-Poc, C

2013-10-15

Polycyclic aromatic hydrocarbons (PAHs) can be preponderant in contaminated sediments and understanding how they are sorbed in the different mineral and organic fractions of the sediment is critical for effective removal strategies. For this purpose, a mixture of seven PAHs was studied at the sediment/water interface and sorption isotherms were obtained. The influence of various factors on the sorption behavior of PAHs was evaluated, such as the nature of minerals, pH, ionic strength and amount of organic matter. Afterwards, the release of PAHs from the sediment by surfactants was investigated. The effectiveness of sodium dodecyl sulfate (SDS) was compared to natural biosurfactants, of cyclolipopeptidic type (amphisin and viscosin-like mixture), produced by two Pseudomonas fluorescens strains. The desorption of PAHs (from naphthalene to pyrene), from the highly retentive kaolinite fraction, could be favored by adding SDS or amphisin, but viscosin-like biosurfactants were only effective for 2-3 ring PAHs desorption (naphthalene to phenanthrene). Moreover, while SDS favors the release of all the target PAHs from a model sediment containing organic matter, the two biosurfactants tested were only effective to desorb the lowest molecular weight PAHs (naphthalene to fluorene). Copyright © 2013 Elsevier B.V. All rights reserved.

Metagenomic discovery of novel enzymes and biosurfactants in a slaughterhouse biofilm microbial community

Science.gov (United States)

Thies, Stephan; Rausch, Sonja Christina; Kovacic, Filip; Schmidt-Thaler, Alexandra; Wilhelm, Susanne; Rosenau, Frank; Daniel, Rolf; Streit, Wolfgang; Pietruszka, Jörg; Jaeger, Karl-Erich

2016-01-01

DNA derived from environmental samples is a rich source of novel bioactive molecules. The choice of the habitat to be sampled predefines the properties of the biomolecules to be discovered due to the physiological adaptation of the microbial community to the prevailing environmental conditions. We have constructed a metagenomic library in Escherichia coli DH10b with environmental DNA (eDNA) isolated from the microbial community of a slaughterhouse drain biofilm consisting mainly of species from the family Flavobacteriaceae. By functional screening of this library we have identified several lipases, proteases and two clones (SA343 and SA354) with biosurfactant and hemolytic activities. Sequence analysis of the respective eDNA fragments and subsequent structure homology modelling identified genes encoding putative N-acyl amino acid synthases with a unique two-domain organisation. The produced biosurfactants were identified by NMR spectroscopy as N-acyltyrosines with N-myristoyltyrosine as the predominant species. Critical micelle concentration and reduction of surface tension were similar to those of chemically synthesised N-myristoyltyrosine. Furthermore, we showed that the newly isolated N-acyltyrosines exhibit antibiotic activity against various bacteria. This is the first report describing the successful application of functional high-throughput screening assays for the identification of biosurfactant producing clones within a metagenomic library. PMID:27271534

Characterization of a biosurfactant produced by Pseudomonas cepacia CCT6659 in the presence of industrial wastes and its application in the biodegradation of hydrophobic compounds in soil.

Science.gov (United States)

Silva, Elias J; Rocha e Silva, Nathália Maria P; Rufino, Raquel D; Luna, Juliana M; Silva, Ricardo O; Sarubbo, Leonie A

2014-05-01

The bacterium Pseudomonas cepacia CCT6659 cultivated with 2% soybean waste frying oil and 2% corn steep liquor as substrates produced a biosurfactant with potential application in the bioremediation of soils. The biosurfactant was classified as an anionic biomolecule composed of 75% lipids and 25% carbohydrates. Characterization by proton nuclear magnetic resonance ((1)H and (13)C NMR) revealed the presence of carbonyl, olefinic and aliphatic groups, with typical spectra of lipids. Four sets of biodegradation experiments were carried out with soil contaminated by hydrophobic organic compounds amended with molasses in the presence of an indigenous consortium, as follows: Set 1-soil+bacterial cells; Set 2-soil+biosurfactant; Set 3-soil+bacterial cells+biosurfactant; and Set 4-soil without bacterial cells or biosurfactant (control). Significant oil biodegradation activity (83%) occurred in the first 10 days of the experiments when the biosurfactant and bacterial cells were used together (Set 3), while maximum degradation of the organic compounds (above 95%) was found in Sets 1-3 between 35 and 60 days. It is evident from the results that the biosurfactant alone and its producer species are both capable of promoting biodegradation to a large extent. Copyright © 2014 Elsevier B.V. All rights reserved.

Sophorolipid biosurfactant against bacteria relevant to tooth caries and skin hygiene

Science.gov (United States)

Sophorolipid (SL) is glycolipid biosurfactant produced by yeast. Its general antimicrobial activity was previously reported. In this paper, we present the antimicrobial activity of SL specifically against oral and skin bacteria. Using a microplate to continuously monitor cell growth, we found com...

Influence of pH on dynamics of microbial enhanced oil recovery processes using biosurfactant producing Pseudomonas putida: Mathematical modelling and numerical simulation.

Science.gov (United States)

Sivasankar, P; Suresh Kumar, G

2017-01-01

In present work, the influence of reservoir pH conditions on dynamics of microbial enhanced oil recovery (MEOR) processes using Pseudomonas putida was analysed numerically from the developed mathematical model for MEOR processes. Further, a new strategy to improve the MEOR performance has also been proposed. It is concluded from present study that by reversing the reservoir pH from highly acidic to low alkaline condition (pH 5-8), flow and mobility of displaced oil, displacement efficiency, and original oil in place (OOIP) recovered gets significantly enhanced, resulting from improved interfacial tension (IFT) reduction by biosurfactants. At pH 8, maximum of 26.1% of OOIP was recovered with higher displacement efficiency. The present study introduces a new strategy to increase the recovery efficiency of MEOR technique by characterizing the biosurfactants for IFT min /IFT max values for different pH conditions and subsequently, reversing the reservoir pH conditions at which the IFT min /IFT max value is minimum. Copyright © 2016 Elsevier Ltd. All rights reserved.

Draft Genome Sequence of a Biosurfactant-Producing Bacillus subtilis UMX-103 Isolated from Hydrocarbon-Contaminated Soil in Terengganu, Malaysia.

Science.gov (United States)

Abdelhafiz, Yousri Abdelmutalab; Manaharan, Thamilvaani; BinMohamad, Saharuddin; Merican, Amir Feisal

2017-07-01

The draft genome here presents the sequence of Bacillus subtilis UMX-103. The bacterial strain was isolated from hydrocarbon-contaminated soil from Terengganu, Malaysia. The whole genome of the bacterium was sequenced using Illumina HiSeq 2000 sequencing platform. The genome was assembled using de novo approach. The genome size of UMX-103 is 4,234,627 bp with 4399 genes comprising 4301 protein-coding genes and 98 RNA genes. The analysis of assembled genes revealed the presence of 25 genes involved in biosurfactant production, where 14 of the genes are related to biosynthesis and 11 of the genes are in the regulation of biosurfactant productions. This draft genome will provide insights into the genetic bases of its biosurfactant-producing capabilities.

Biosurfactant production from marine hydrocarbon-degrading consortia and pure bacterial strains using crude oil as carbon source

Directory of Open Access Journals (Sweden)

Eleftheria eAntoniou

2015-04-01

Full Text Available Biosurfactants (BS are green amphiphilic molecules produced by microorganisms during biodegradation, increasing the bioavailability of organic pollutants. In this work, the BS production yield of marine hydrocarbon degraders isolated from Elefsina bay in Eastern Mediterranean Sea has been investigated. The drop collapse test was used as a preliminary screening test to confirm biosurfactant producing strains or mixed consortia. The community structure of the best consortia based on the drop collapse test was determined by 16S-rDNA pyrotag screening. Subsequently, the effect of incubation time, temperature, substrate and supplementation with inorganic nutrients, on biosurfactant production, was examined. Two types of BS - lipid mixtures were extracted from the culture broth; the low molecular weight BS Rhamnolipids and Sophorolipids. Crude extracts were purified by silica gel column chromatography and then identified by thin layer chromatography (TLC and Fourier transform infrared spectroscopy (FT-IR. Results indicate that biosurfactant production yield remains constant and low while it is independent of the total culture biomass, carbon source, and temperature. A constant BS concentration in a culture broth with continuous degradation of crude oil implies that the BS producing microbes generate no more than the required amount of biosurfactants that enables biodegradation of the crude oil. Isolated pure strains were found to have higher specific production yields than the complex microbial marine community-consortia. The heavy oil fraction of crude oil has emerged as a promising substrate for BS production (by marine BS producers with fewer impurities in the final product. Furthermore, a particular strain isolated from sediments, Paracoccus marcusii, may be an optimal choice for bioremediation purposes as its biomass remains trapped in the hydrocarbon phase, not suffering from potential dilution effects by sea currents.

Simultaneous production of detergent stable keratinolytic protease, amylase and biosurfactant by Bacillus subtilis PF1 using agro industrial waste.

Science.gov (United States)

Bhange, Khushboo; Chaturvedi, Venkatesh; Bhatt, Renu

2016-06-01

The present study is an attempt to optimize simultaneous production of keratinolytic protease, amylase and biosurfactant from feather meal, potato peel and rape seed cake in a single media by response surface methodology to evaluate their biochemical properties for detergent additive. The optimization was carried out using 20 run, 3 factor and 5-level of central composite design on design expert software which resulted in a 1.2, 0.84 and 2.28 fold increase in protease, amylase and biosurfactant production. The proteolytic activity was found to be optimum at pH 9.0 and 60 °C while optimum amylolytic activity was recorded at pH 6.0 and 70 °C respectively. Both enzymes were found to be stable in the presence of organic solvents, ionic and commercial detergent and oxidizing agents. The biosurfactant was extracted with chloroform and was found to be stable at varying pH and temperature; however a reduction in the activity was observed at temperature higher than 70 °C. The isolated enzymes and biosurfactants may find applications in the effective removal of stains.

Improved Energy Recovery by Anaerobic Grey Water Sludge Treatment with Black Water

Directory of Open Access Journals (Sweden)

Taina Tervahauta

2014-08-01

Full Text Available This study presents the potential of combining anaerobic grey water sludge treatment with black water in an up-flow anaerobic sludge blanket (UASB reactor to improve energy recovery within source-separated sanitation concepts. Black water and the mixture of black water and grey water sludge were compared in terms of biochemical methane potential (BMP, UASB reactor performance, chemical oxygen demand (COD mass balance and methanization. Grey water sludge treatment with black water increased the energy recovery by 23% in the UASB reactor compared to black water treatment. The increase in the energy recovery can cover the increased heat demand of the UASB reactor and the electricity demand of the grey water bioflocculation system with a surplus of 0.7 kWh/cap/y electricity and 14 MJ/cap/y heat. However, grey water sludge introduced more heavy metals in the excess sludge of the UASB reactor and might therefore hinder its soil application.

Oxygen-controlled Biosurfactant Production in a Bench Scale Bioreactor

Science.gov (United States)

de Kronemberger, Frederico Araujo; Anna, Lidia Maria Melo Santa; Fernandes, Ana Carolina Loureiro Brito; de Menezes, Reginaldo Ramos; Borges, Cristiano Piacsek; Freire, Denise Maria Guimarães

Rhamnolipids have been pointed out as promising biosurfactants. The most studied microorganisms for the aerobic production of these molecules are the bacteria of the genus Pseudomonas. The aim of this work was to produce a rhamnolipid-type biosurfactant in a bench-scale bioreactor by one strain of Pseudomonas aeruginosa isolated from oil environments. To study the microorganism growth and production dependency on oxygen, a nondispersive oxygenation device was developed, and a programmable logic controller (PLC) was used to set the dissolved oxygen (DO) concentration. Using the data stored in a computer and the predetermined characteristics of the oxygenation device, it was possible to evaluate the oxygen uptake rate (OUR) and the specific OUR (SOUR) of this microorganism. These rates, obtained for some different DO concentrations, were then compared to the bacterial growth, to the carbon source consumption, and to the rhamnolipid and other virulence factors production. The SOUR presented an initial value of about 60.0 mg02/gdw h. Then, when the exponential growth phase begins, there is a rise in this rate. After that, the SOUR reduces to about 20.0 mg02/gdw h. The carbon source consumption is linear during the whole process.

The emulsifying effect of biosurfactants produced by food spoilage organisms in Nigeria

Directory of Open Access Journals (Sweden)

Christianah O. Ogunmola

2016-04-01

Full Text Available Food spoilage organisms were isolated using standard procedures on Nutrient Agar, Cetrimide Agar and Pseudomonas Agar Base (supplemented with CFC. The samples were categorized as animal products (raw fish, egg, raw chicken, corned beef, pasteurized milk and plant products (vegetable salad, water leaf (Talinium triangulare, boiled rice, tomatoes and pumpkin leaf (Teifairia occidentalis.They were characterised as Pseudomonas putida, Pseudomonas aeruginosa, Pseudomonas stutzeri, Burkholderia pseudomallei, Serratia rubidaea, Corynebacterium pilosum, Bacillus subtilis, Bacillus mycoides, Bacillus laterosporus, Bacillus laterosporus, Serratia marcescens, Bacillus cereus, Bacillus macerans, Alcaligenes faecalis and Alcaligenes eutrophus. Preliminary screening for biosurfactant production was done using red blood haemolysis test and confirmed by slide test, drop collapse and oil spreading assay. The biosurfactant produced was purified using acetone and the composition determined initially using Molisch’s test, thin layer chromatography and gas chromatography mass spectrometry. The components were found to be ethanol, amino acids, butoxyacetic acid, hexadecanoic acid, oleic acid, lauryl peroxide, octadecanoic acid and phthalic acid. The producing organisms grew readily on several hydrocarbons such as crude oil, diesel oil and aviation fuel when used as sole carbon sources.  The purified biosurfactants produced were able to cause emulsification of kerosene (19.71-27.14% as well as vegetable oil (16.91-28.12% based on the emulsification index. This result suggests that the isolates can be an asset and further work can exploit their optimal potential in industries.

Parameters examination of a biosurfactant production at laboratory scale

International Nuclear Information System (INIS)

Rosero, Neira Gladys; Pimienta, Astrid Lorely; Dugarte, Fanny; Carvajal, Fredy Gonzalo

2003-01-01

This work presents the results obtained from the laboratory-scale experimentation for the optimization of production of rhamnolipid type biosurfactant in a batch process, through the calculation and analysis of yield parameters. Different carbon/nitrogen ratios were studied, for which the production rates of rhamnolipid under nitrogen limitation was defined. Bacterial growth yield parameters Y X/N and Y X/C , were also calculated

Self-assembly of nanoscale particles with biosurfactants and membrane scaffold proteins.

Science.gov (United States)

Faas, Ramona; Pohle, Annelie; Moß, Karin; Henkel, Marius; Hausmann, Rudolf

2017-12-01

Nanodiscs are membrane mimetics which may be used as tools for biochemical and biophysical studies of a variety of membrane proteins. These nanoscale structures are composed of a phospholipid bilayer held together by an amphipathic membrane scaffold protein (MSP). In the past, nanodiscs were successfully assembled with membrane scaffold protein 1D1 and 1,2-dipalmitoyl- sn -glycero-3-phosphorylcholine with a homogeneous diameter of ∼10 nm. In this study, the formation of nanoscale particles from MSP1D1 and rhamnolipid biosurfactants is investigated. Different protein to lipid ratios of 1:80, 1:90 and 1:100 were used for the assembly reaction, which were consecutively separated, purified and analyzed by size-exclusion chromatography (SEC) and dynamic light scattering (DLS). Size distributions were measured to determine homogeneity and confirm size dimensions. In this study, first evidence is presented on the formation of nanoscale particles with rhamnolipid biosurfactants and membrane scaffold proteins.

Physicochemical and functional characterization of a biosurfactant produced by Lactococcus lactis 53

NARCIS (Netherlands)

Rodrigues, LR; Teixeira, JA; van der Mei, HC; Oliveira, R

2006-01-01

Isolation and identification of key components of the crude biosurfactant produced by Lactococcus lactis 53 was studied. Fractionation was achieved by hydrophobic interaction chromatography which allowed the isolation of a fraction rich in glycoproteins. Molecular (by Fourier transform infrared

Biosurfactants' Production from Renewable Natural Resources: Example of Innovativeand Smart Technology in Circular Bioeconomy

Science.gov (United States)

Satpute, Surekha K.; Płaza, Grażyna A.; Banpurkar, Arun G.

2017-03-01

A strong developed bio-based industrial sector will significantly reduce dependency on fossil resources, help the countries meet climate change targets, and lead to greener and more environmental friendly growth. The key is to develop new technologies to sustainably transform renewable natural resources into bio-based products and biofuels. Biomass is a valuable resource and many parameters need to be taken in to account when assessing its use and the products made from its. The bioeconomy encompass the production of renewable biological resources and their conversion into food, feed and bio-based products (chemicals, materials and fuels) via innovative and efficient technologies provided by industrial biotechnology. The paper presents the smart and efficient way to use the agro-industrial, dairy and food processing wastes for biosurfactant's production. Clarification processes are mandatory to use the raw substrates for microbial growth as well as biosurfactant production for commercial purposes. At the same time it is very essential to retain the nutritional values of those cheap substrates. Broad industrial perspectives can be achieved when quality as well as the quantity of the biosurfactant is considered in great depth. Since substrates resulting from food processing, dairy, animal fat industries are not explored in great details; and hence are potential areas which can be explored thoroughly.

Enhancement of recovery of residual oil using a biosurfactant slug ...

African Journals Online (AJOL)

Characterization of the biosurfactant extract revealed a mixture of glycolipid and phospholipid in a ratio of 3.35:1. The irreducible water saturation (Swi) and initial residual oil saturation (Sor) of the sand-pack were 0.280 ± 0.003 and 0.373 ± 0.006, respectively. Core flooding experiment showed that an optimum oil recovery ...

Antibiotic and biosurfactant properties of cyclic lipopeptides produced by fluorescent Pseudomonas spp. from the sugar beet rhizosphere

DEFF Research Database (Denmark)

Nielsen, T H; Sørensen, D; Tobiasen, C

2002-01-01

Cyclic lipopeptides (CLPs) with antibiotic and biosurfactant properties are produced by a number of soil bacteria, including fluorescent Pseudomonas spp. To provide new and efficient strains for the biological control of root-pathogenic fungi in agricultural crops, we isolated approximately 600...... in the peptide moiety. Production of specific CLPs could be affiliated with Pseudomonas fluorescens strain groups belonging to biotype I, V, or VI. In vitro analysis using both purified CLPs and whole-cell P. fluorescens preparations demonstrated that all CLPs exhibited strong biosurfactant properties...

Isolation and characterization of a biosurfactant-producing heavy metal resistant Rahnella sp. RM isolated from chromium-contaminated soil

OpenAIRE

GOVARTHANAN, Muthusamy; MYTHILI, R.; SELVANKUMAR, Thangasamy; KAMALA-KANNAN, S.; CHOI, DuBok; CHANG, Young-Cheol

2017-01-01

Objective of the study was to isolate heavy metal resistant bacteria from chromium-contaminated subsurface soil and investigate biosurfactant production and heavy metal bioremediation. Based on 16S rRNA gene sequence and phylogenetic analysis, the isolate was identified as Rahnella sp. RM. The biosurfactant production by heavy metal resistant Rahnella sp. RM was optimized using Box- Behnken design (BBD). The maximum emulsification activity was obtained 66% at 6% soybean meal in pH 7.0 and 33....

Biosurfactants produced by Bacillus subtilis A1 and Pseudomonas stutzeri NA3 reduce longevity and fecundity of Anopheles stephensi and show high toxicity against young instars.

Science.gov (United States)

Parthipan, Punniyakotti; Sarankumar, Raja Kumaresan; Jaganathan, Anitha; Amuthavalli, Pandian; Babujanarthanam, Ranganathan; Rahman, Pattanathu K S M; Murugan, Kadarkarai; Higuchi, Akon; Benelli, Giovanni; Rajasekar, Aruliah

2018-04-01

Anopheles stephensi acts as vector of Plasmodium parasites, which are responsible for malaria in tropical and subtropical areas worldwide. Currently, malaria management is a big challenge due to the presence of insecticide-resistant strains as well as to the development of Plasmodium species highly resistant to major antimalarial drugs. Therefore, the present study focused on biosurfactant produced by two bacteria Bacillus subtilis A1 and Pseudomonas stutzeri NA3, evaluating them for insecticidal applications against malaria mosquitoes. The produced biosurfactants were characterized using FT-IR spectroscopy and gas chromatography-mass spectrometry (GC-MS), which confirmed that biosurfactants had a lipopeptidic nature. Both biosurfactants were tested against larvae and pupae of A. stephensi. LC 50 values were 3.58 (larva I), 4.92 (II), 5.73 (III), 7.10 (IV), and 7.99 (pupae) and 2.61 (I), 3.68 (II), 4.48 (III), 5.55 (IV), and 6.99 (pupa) for biosurfactants produced by B. subtilis A1 and P. stutzeri NA3, respectively. Treatments with bacterial surfactants led to various physiological changes including longer pupal duration, shorter adult oviposition period, and reduced longevity and fecundity. To the best of our knowledge, there are really limited reports on the mosquitocidal and physiological effects due to biosurfactant produced by bacterial strains. Overall, the toxic activity of these biosurfactant on all young instars of A. stephensi, as well as their major impact on adult longevity and fecundity, allows their further consideration for the development of insecticides in the fight against malaria mosquitoes.

Methods for investigating biosurfactants and bioemulsifiers: a review.

Science.gov (United States)

Satpute, Surekha K; Banpurkar, Arun G; Dhakephalkar, Prashant K; Banat, Ibrahim M; Chopade, Balu A

2010-06-01

Microorganisms produce biosurfactant (BS)/bioemulsifier (BE) with wide structural and functional diversity which consequently results in the adoption of different techniques to investigate these diverse amphiphilic molecules. This review aims to compile information on different microbial screening methods, surface active products extraction procedures, and analytical terminologies used in this field. Different methods for screening microbial culture broth or cell biomass for surface active compounds production are also presented and their possible advantages and disadvantages highlighted. In addition, the most common methods for purification, detection, and structure determination for a wide range of BS and BE are introduced. Simple techniques such as precipitation using acetone, ammonium sulphate, solvent extraction, ultrafiltration, ion exchange, dialysis, ultrafiltration, lyophilization, isoelectric focusing (IEF), and thin layer chromatography (TLC) are described. Other more elaborate techniques including high pressure liquid chromatography (HPLC), infra red (IR), gas chromatography-mass spectroscopy (GC-MS), nuclear magnetic resonance (NMR), and fast atom bombardment mass spectroscopy (FAB-MS), protein digestion and amino acid sequencing are also elucidated. Various experimental strategies including static light scattering and hydrodynamic characterization for micelles have been discussed. A combination of various analytical methods are often essential in this area of research and a numbers of trials and errors to isolate, purify and characterize various surface active agents are required. This review introduces the various methodologies that are indispensable for studying biosurfactants and bioemulsifiers.

Modified anaerobic digestion elutriated phased treatment for the anaerobic co-digestion of sewage sludge and food wastewater.

Science.gov (United States)

Mo, Kyung; Lee, Wonbae; Kim, Moonil

2017-02-01

A modified anaerobic digestion elutriated phased treatment (MADEPT) process was developed for investigating anaerobic co-digestion of sewage sludge and food wastewater. The anaerobic digestion elutriated phased treatment (ADEPT) process is similar to a two-phase system, however, in which the effluent from a methanogenic reactor recycles into an acidogenic reactor to elutriate mainly dissolved organics. Although ADEPT could reduce reactor volume significantly, the unsolubilized solids should be wasted from the system. The MADEPT process combines thermo-alkali solubilization with ADEPT to improve anaerobic performance and to minimize the sludge disposal. It was determined that the optimal volume mixing ratio of sewage sludge and food wastewater was 4 : 1 for the anaerobic co-digestion. The removal efficiencies of total chemical oxygen demand, volatile solids, and volatile suspended solids in the MADEPT process were 73%, 70%, and 64%, respectively. However, those in the ADEPT process were only 48%, 37%, and 40%, respectively, at the same hydraulic retention time (HRT) of 7 days. The gas production of MADEPT was two times higher than that of ADEPT. The thermo-alkali solubilization increased the concentration of dissolved organics so that they could be effectively degraded in a short HRT, implying that MADEPT could improve the performance of ADEPT in anaerobic co-digestion.

Lipopeptide biosurfactant viscosin enhances dispersal of Pseudomonas fluorescens SBW25 biofilms

DEFF Research Database (Denmark)

Bonnichsen, Lise; Svenningsen, Nanna Bygvraa; Rybtke, Morten Levin

2015-01-01

Pseudomonads produce several lipopeptide biosurfactants that have antimicrobial properties but that also facilitate surface motility and influence biofilm formation. Detailed studies addressing the significance of lipopeptides for biofilm formation and architecture are rare. Hence, the present...

Production of biosurfactants for application in the removal of environmental contaminants generated in the petroleum industry; Producao de biossurfactantes para aplicacao na remocao de contaminantes ambientais gerados na industria do petroleo

Energy Technology Data Exchange (ETDEWEB)

Sarubbo, Leonie A.; Rufino, Raquel D.; Luna, Juliana M. de; Farias, Charles B.B.; Santos, Valdemir A. dos [Universidade Catolica de Pernambuco (UNICAP), Recife, PE (Brazil)

2012-07-01

This paper describes the application of microbial surfactants in removing crude oil and marine environment located in the proximity of the Pernambuco Thermoelectric. Two biosurfactants were produced by yeasts Candida sphaerica and C. lipolytica grown in industrial wastes during 72 and 144 hours, respectively. The surface tensions of the biomolecules (25 mN/m) were determined, the production yields were estimated (8 and 9 g/L) and the CMC determined (0.03%). The biosurfactants were applied to samples of sea water and rocks contaminated with petroleum and motor oil. The results demonstrated the oil dispersant action of the biosurfactant from C. sphaerica and the emulsifying ability of the biosurfactant from C. lipolytica. Percentages removals of 100% of oil and petroleum were obtained for both biosurfactants. The possibility of application of biosurfactants in the remediation of oil polluted environments motivates the advancement of research to develop this alternative technology for effective use in the Termope Thermoelectric treatment systems. (author)

Anaerobic prosthetic joint infection.

Science.gov (United States)

Shah, Neel B; Tande, Aaron J; Patel, Robin; Berbari, Elie F

2015-12-01

In an effort to improve mobility and alleviate pain from degenerative and connective tissue joint disease, an increasing number of individuals are undergoing prosthetic joint replacement in the United States. Joint replacement is a highly effective intervention, resulting in improved quality of life and increased independence [1]. By 2030, it is predicted that approximately 4 million total hip and knee arthroplasties will be performed yearly in the United States [2]. One of the major complications associated with this procedure is prosthetic joint infection (PJI), occurring at a rate of 1-2% [3-7]. In 2011, the Musculoskeletal Infectious Society created a unifying definition for prosthetic joint infection [8]. The following year, the Infectious Disease Society of America published practice guidelines that focused on the diagnosis and management of PJI. These guidelines focused on the management of commonly encountered organisms associated with PJI, including staphylococci, streptococci and select aerobic Gram-negative bacteria. However, with the exception of Propionibacterium acnes, management of other anaerobic organisms was not addressed in these guidelines [1]. Although making up approximately 3-6% of PJI [9,10], anaerobic microorganisms cause devastating complications, and similar to the more common organisms associated with PJI, these bacteria also result in significant morbidity, poor outcomes and increased health-care costs. Data on diagnosis and management of anaerobic PJI is mostly derived from case reports, along with a few cohort studies [3]. There is a paucity of published data outlining factors associated with risks, diagnosis and management of anaerobic PJI. We therefore reviewed available literature on anaerobic PJI by systematically searching the PubMed database, and collected data from secondary searches to determine information on pathogenesis, demographic data, clinical features, diagnosis and management. We focused our search on five commonly

Lactic Acid and Biosurfactants Production from Residual Cellulose Films.

Science.gov (United States)

Portilla Rivera, Oscar Manuel; Arzate Martínez, Guillermo; Jarquín Enríquez, Lorenzo; Vázquez Landaverde, Pedro Alberto; Domínguez González, José Manuel

2015-11-01

The increasing amounts of residual cellulose films generated as wastes all over the world represent a big scale problem for the meat industry regarding to environmental and economic issues. The use of residual cellulose films as a feedstock of glucose-containing solutions by acid hydrolysis and further fermentation into lactic acid and biosurfactants was evaluated as a method to diminish and revalorize these wastes. Under a treatment consisting in sulfuric acid 6% (v/v); reaction time 2 h; solid liquid ratio 9 g of film/100 mL of acid solution, and temperature 130 °C, 35 g/L of glucose and 49% of solubilized film was obtained. From five lactic acid strains, Lactobacillus plantarum was the most suitable for metabolizing the glucose generated. The process was scaled up under optimized conditions in a 2-L bioreactor, producing 3.4 g/L of biomass, 18 g/L of lactic acid, and 15 units of surface tension reduction of a buffer phosphate solution. Around 50% of the cellulose was degraded by the treatment applied, and the liqueurs generated were useful for an efficient production of lactic acid and biosurfactants using L. plantarum. Lactobacillus bacteria can efficiently utilize glucose from cellulose films hydrolysis without the need of clarification of the liqueurs.

Characterization of hydrocarbon-degrading and biosurfactant-producing Pseudomonas sp. P-1 strain as a potential tool for bioremediation of petroleum-contaminated soil.

Science.gov (United States)

Pacwa-Płociniczak, Magdalena; Płaza, Grażyna Anna; Poliwoda, Anna; Piotrowska-Seget, Zofia

2014-01-01

The Pseudomonas sp. P-1 strain, isolated from heavily petroleum hydrocarbon-contaminated soil, was investigated for its capability to degrade hydrocarbons and produce a biosurfactant. The strain degraded crude oil, fractions A5 and P3 of crude oil, and hexadecane (27, 39, 27 and 13% of hydrocarbons added to culture medium were degraded, respectively) but had no ability to degrade phenanthrene. Additionally, the presence of gene-encoding enzymes responsible for the degradation of alkanes and naphthalene in the genome of the P-1 strain was reported. Positive results of blood agar and methylene blue agar tests, as well as the presence of gene rhl, involved in the biosynthesis of rhamnolipid, confirmed the ability of P-1 for synthesis of glycolipid biosurfactant. 1H and 13C nuclear magnetic resonance, Fourier transform infrared spectrum and mass spectrum analyses indicated that the extracted biosurfactant was affiliated with rhamnolipid. The results of this study indicate that the P-1 and/or biosurfactant produced by this strain have the potential to be used in bioremediation of hydrocarbon-contaminated soils.

Biosurfactant and enzyme mediated crude oil degradation by Pseudomonas stutzeri NA3 and Acinetobacter baumannii MN3.

Science.gov (United States)

Parthipan, Punniyakotti; Elumalai, Punniyakotti; Sathishkumar, Kuppusamy; Sabarinathan, Devaraj; Murugan, Kadarkarai; Benelli, Giovanni; Rajasekar, Aruliah

2017-10-01

The present study focuses on the optimization of biosurfactant (BS) production using two potential biosurfactant producer Pseudomonas stutzeri NA3 and Acinetobacter baumannii MN3 and role of enzymes in the biodegradation of crude oil. The optimal conditions for P. stutzeri NA3 and A. baumannii MN3 for biodegradation were pH of 8 and 7; temperature of 30 and 40 °C, respectively. P. stutzeri NA3 and A. baumannii MN3 produced 3.81 and 4.68 g/L of BS, respectively. Gas chromatography mass spectrometry confirmed that BS was mainly composed of fatty acids. Furthermore, the role of the degradative enzymes, alkane hydroxylase, alcohol dehydrogenase and laccase on biodegradation of crude oil are explained. Maximum biodegradation efficiency (BE) was recorded for mixed consortia (86%) followed by strain P. stutzeri NA3 (84%). Both bacterial strains were found to be vigorous biodegraders of crude oil than other biosurfactant-producing bacteria due to their enzyme production capabilities and our results suggests that the bacterial isolates can be used for effective degradation of crude oil within short time periods.

Comparison of some indigenous bacterial strains of pseudomonas ssp. for production of biosurfactants

International Nuclear Information System (INIS)

Sahafeeq, M.; Kokub, D.; Khalid, Z.M.; Malik, K.A.

1991-01-01

Some indigenous pseudomonas spp. were found to have the ability of emulsification, lowering the surface and interfacial tensions, and formation of high reciprocal CMCs. Six strains of Pseudomonas spp were compared for biosurfactant production grown on hexadecane. Supernatant from whole culture broth of these strains could lower surface tension from 65 mN/m to 28-32 nM/m, interfacial tension from 40 nM/m to 1-3 mN/m and had high reciprocal CMCs. When compared for emulsification ability by the culture broth of these strains, the emulsification index (E24) was found to range between 60-65. Biosurfactant containing culture broth of some strains could retain the property up to 80 C, pH of 13 and sodium chloride concentration for 17% which indicates their possible role in some depleted oil well. (author)

Aneurinifactin, a new lipopeptide biosurfactant produced by a marine Aneurinibacillus aneurinilyticus SBP-11 isolated from Gulf of Mannar: Purification, characterization and its biological evaluation.

Science.gov (United States)

Balan, Shanmugasundaram Senthil; Kumar, C Ganesh; Jayalakshmi, Singaram

2017-01-01

Biosurfactants are microbial-derived amphiphilic molecules having hydrophobic and hydrophilic moieties produced by bacteria, fungi, yeasts and algae and are extracellular or cell wall-associated compounds. In an ongoing survey for bioactive microbial metabolites from microbes isolated from diverse ecological niches, a new lipopeptide biosurfactant was identified from a marine bacterium; Aneurinibacillus aneurinilyticus strain SBP-11, which was isolated from a marine diversity hotspot, Gulf of Mannar, India. A new lipopeptide biosurfactant was purified and characterized based on TLC, FT-IR, NMR, GC-MS, HPLC, MALDI-TOF-MS and tandem MS analysis as Stearic acid-Thr-Tyr-Val-Ser-Tyr-Thr (named as Aneurinifactin). The critical micelle concentration of Aneurinifactin was 26mgL -1 at a surface tension of 26mNm -1 . Further, the biosurfactant showed stable emulsification at a wide range of pH (2-9) and temperature up to 80°C. Aneurinifactin showed promising antimicrobial activity and concentration dependent efficient oil recovery. This is the first report on Aneurinifactin, a lipopeptide biosurfactant produced by a marine A. aneurinilyticus SBP-11, which could be explored as a promising candidate for use in various biomedical and industrial applications. Copyright © 2016 Elsevier GmbH. All rights reserved.

New Transfection Agents Based on Liposomes Containing Biosurfactant MEL-A.

Science.gov (United States)

Nakanishi, Mamoru; Inoh, Yoshikazu; Furuno, Tadahide

2013-08-16

Nano vectors are useful tools to deliver foreign DNAs, oligonucleotides, and small interfering double-stranded RNAs (siRNAs) into mammalian cells with gene transfection and gene regulation. In such experiments we have found the liposomes with a biosurfacant mannosylerythriol lipid (MEL-A) are useful because of their high transfer efficiency, and their unique mechanism to transfer genes to target cells with the lowest toxicity. In the present review we will describe our current work, which may contribute to the great advance of gene transfer to target cells and gene regulations. For more than two decades, the liposome technologies have changed dramatically and various methods have been proposed in the fields of biochemistry, cell biology, biotechnology, and so on. In addition, they were towards to pharmaceutics and clinical applications. The liposome technologies were expected to use gene therapy, however, they have not reached a requested goal as of yet. In the present paper we would like to present an approach using a biosurfactant, MEL-A, which is a surface-active compound produced by microorganisms growing on water-insoluble substrates and increases efficiency in gene transfection. The present work shows new transfection agents based on liposomes containing biosurfactant MEL-A.

Reducing COD level on oily effluent by utilizing biosurfactant-producing bacteria

Directory of Open Access Journals (Sweden)

Daniela Franco Carvalho Jacobucci

2009-08-01

Full Text Available Two bacteria isolated from crude oil contaminated soil, Pantoea agglomerans and Planococcus citreus, produced biosurfactants utilizing 1.5% of kerosene and olive oil as the sole carbon sources, respectively. The bacteria and the biosurfactants produced were introduced to oily effluent, arising from margarine and soap industry. Emulsification activities were determined by increases in the absorbance of the oil-in-water emulsions at 610 nm, whereas the water-in-oil emulsions were expressed as the height (cm of the emulsion layers formed. The 72 h incubation experiment resulted in a COD (Chemical Oxygen Demand reduction of 76% with Planococcus citreus strain and 70% with Pantoea agglomerans.The COD reduction with bacterial biosurfactants was over 50% in 24 h of incubation. The COD reduction showed that these strains and the surfactants produced could be used in bioremediation processes.Duas bactérias isoladas de solo contaminado com derivados de petróleo, Pantoea agglomerans e Planococcus citreus, produzem biosurfactantes utilizando respectivamente 1.5% de querosene e óleo de oliva como únicas fontes de carbono. As bactérias e os biosurfactantes produzidos foram adicionados a um efluente oleoso obtido de uma indústria nacional de sabão e margarina. As atividades de emulsificação foram determinadas pelo aumento da absorbância das emulsões óleo em água a 610 nm, enquanto que as emulsões do tipo água em óleo foram expressas em centímetros, pela altura do halo de espumas formado. A redução da demanda química de oxigênio (COD mostra que as linhagens e os biosurfactantes produzidos podem ser utilizados em processos de biorremediação.

Physiologically anaerobic microorganisms of the deep subsurface

Energy Technology Data Exchange (ETDEWEB)

Stevens, S.E. Jr.; Chung, K.T.

1991-06-01

This study seeks to determine numbers, diversity, and morphology of anaerobic microorganisms in 15 samples of subsurface material from the Idaho National Engineering Laboratory, in 18 samples from the Hanford Reservation and in 1 rock sample from the Nevada Test Site; set up long term experiments on the chemical activities of anaerobic microorganisms based on these same samples; work to improve methods for the micro-scale determination of in situ anaerobic microbial activity;and to begin to isolate anaerobes from these samples into axenic culture with identification of the axenic isolates.

Integrated Nanozero Valent Iron and Biosurfactant-Aided Remediation of PCB-Contaminated Soil

Directory of Open Access Journals (Sweden)

He Zhang

2016-01-01

Full Text Available Polychlorobiphenyls (PCBs have been identified as environmental hazards for years. Due to historical issues, a considerable amount of PCBs was released deep underground in Canada. In this research, a nanoscale zero valent iron- (nZVI- aided dechlorination followed by biosurfactant enhanced soil washing method was developed to remove PCBs from soil. During nZVI-aided dechlorination, the effects of nZVI dosage, initial pH level, and temperature were evaluated, respectively. Five levels of nZVI dosage and two levels of initial pH were experimented to evaluate the PCB dechlorination rate. Additionally, the temperature changes could positively influence the dechlorination process. In soil washing, the presence of nanoiron particles played a key role in PCB removal. The crude biosurfactant was produced using a bacterial stain isolated from the Atlantic Ocean and was applied for soil washing. The study has led to a promising technology for PCB-contaminated soil remediation.

Biogeographical distribution analysis of hydrocarbon degrading and biosurfactant producing genes suggests that near-equatorial biomes have higher abundance of genes with potential for bioremediation.

Science.gov (United States)

Oliveira, Jorge S; Araújo, Wydemberg J; Figueiredo, Ricardo M; Silva-Portela, Rita C B; de Brito Guerra, Alaine; da Silva Araújo, Sinara Carla; Minnicelli, Carolina; Carlos, Aline Cardoso; de Vasconcelos, Ana Tereza Ribeiro; Freitas, Ana Teresa; Agnez-Lima, Lucymara F

2017-07-27

Bacterial and Archaeal communities have a complex, symbiotic role in crude oil bioremediation. Their biosurfactants and degradation enzymes have been in the spotlight, mainly due to the awareness of ecosystem pollution caused by crude oil accidents and their use. Initially, the scientific community studied the role of individual microbial species by characterizing and optimizing their biosurfactant and oil degradation genes, studying their individual distribution. However, with the advances in genomics, in particular with the use of New-Generation-Sequencing and Metagenomics, it is now possible to have a macro view of the complex pathways related to the symbiotic degradation of hydrocarbons and surfactant production. It is now possible, although more challenging, to obtain the DNA information of an entire microbial community before automatically characterizing it. By characterizing and understanding the interconnected role of microorganisms and the role of degradation and biosurfactant genes in an ecosystem, it becomes possible to develop new biotechnological approaches for bioremediation use. This paper analyzes 46 different metagenome samples, spanning 20 biomes from different geographies obtained from different research projects. A metagenomics bioinformatics pipeline, focused on the biodegradation and biosurfactant-production pathways, genes and organisms, was applied. Our main results show that: (1) surfactation and degradation are correlated events, and therefore should be studied together; (2) terrestrial biomes present more degradation genes, especially cyclic compounds, and less surfactation genes, when compared to water biomes; and (3) latitude has a significant influence on the diversity of genes involved in biodegradation and biosurfactant production. This suggests that microbiomes found near the equator are richer in genes that have a role in these processes and thus have a higher biotechnological potential. In this work we have focused on the

Individually and Synergistic Degradation of Hydrocarbons by Biosurfactant Producing Bacteria

Directory of Open Access Journals (Sweden)

Amirarsalan Kavyanifard

2016-02-01

Full Text Available Background: Increasing worldwide contamination with hydrocarbons has urged environmental remediation using biological agents such as bacteria. Our goal here was to study the phylogenetic relationship of two crude oil degrader bacteria and investigation of their ability to degrade hydrocarbons. Materials and Methods: Phylogenetic relationship of isolates was determined using morphological and biochemical characteristics and 16S rDNA gene sequencing. Optimum conditions of each isolate for crude oil degradation were investigated using one factor in time method. The rate of crude oil degradation by individual and consortium bacteria was assayed via Gas chromatography–mass spectrometry (GC-MS analysis. Biosurfactant production was measured by Du Noüy ring method using Krüss-K6 tensiometer. Results: The isolates were identified as Dietzia cinnamea KA1 and Dietzia cinnamea AP and clustered separately, while both are closely related to each other and with other isolates of Dietzia cinnamea. The optimal conditions for D. cinnamea KA1 were 35°C, pH9.0, 510 mM NaCl, and minimal requirement of 46.5 mM NH4Cl and 2.10 mM NaH2PO4. In the case of D. cinnamea AP, the values were 30°C, pH8.0, 170 mM NaCl, and minimal requirement of 55.8 mM NH4Cl and 2.10 mM NaH2PO4, respectively. Gas chromatography – Mass Spectroscopy (GC-MS analysis showed that both isolates were able to utilize various crude oil compounds, but D. cinnamea KA1 was more efficient individually and consortium of isolates was the most. The isolates were able to grow and produce biosurfactant when cultured in MSM supplemented with crude oil and optimization of MSM conditions lead to increase in biosurfactant production. Conclusion: To the best of our knowledge this is the first report of synergistic relationship between two strains of D. cinnamea in biodegradation of crude oil components, including poisonous and carcinogenic compound in a short time.

Application of Biosurfactants Produced by Pseudomonas putida using Crude Palm Oil (CPO) as Substrate for Crude Oil Recovery using Batch Method

Science.gov (United States)

Suryanti, V.; Handayani, D. S.; Masykur, A.; Septyaningsih, I.

2018-03-01

The application of biosurfactants which have been produced by Pseudomonas putida in nutrient broth medium supplemented with NaCl and crude palm oil (CPO) for oil recovery has been evaluated. The crude and purified biosurfactants have been examined for oil recovery from a laboratory oil-contaminated sand in agitated flask (batch method). Two synthetic surfactants and water as control was also performed for oil recovery as comparisons. Using batch method, the results showed that removing ability of crude oil from the oil-contaminated sand by purified and crude biosurfactants were 79.40±3.10 and 46.84±2.23 %, respectively. On other hand, the recoveries obtained with the SDS, Triton X-100 and water were 94.33±0.47, 74.84±7.39 and 34.42±1.21%respectively.

Streptococcus thermophilus and its biosurfactants inhibit adhesion by Candida spp. on silicone rubber

NARCIS (Netherlands)

Busscher, HJ; vanHoogmoed, CG; GeertsemaDoornbusch, GI; vanderKuijlBooij, M; vanderMei, HC

1997-01-01

The adhesion of yeasts, two Candida albicans and two Candida tropicalis strains isolated from naturally colonized voice prostheses, to silicone rubber with and without a salivary conditioning film in the absence and presence of adhering Streptococcus thermophilus B, a biosurfactant-releasing dairy

Role of Bacillus licheniformis VS16-Derived Biosurfactant in Mediating Immune Responses in Carp Rohu and its Application to the Food Industry

Science.gov (United States)

Giri, Sib Sankar; Sen, Shib Sankar; Jun, Jin Woo; Sukumaran, V.; Park, Se Chang

2017-01-01

Multifarious applications of Bacillus licheniformis VS16-derived biosurfactant were explored. Labeo rohita fingerlings were injected intraperitoneally with 0.1 mL of phosphate-buffered saline (PBS) containing purified biosurfactant at 0 (control), 55 (S55), 110 (S110), 220 (S220), or 330 (S330) μg mL-1 concentrations. Various immunological parameters and the expression of immune-related genes were measured at 7, 14, and 21 days post-administration (dpa). At 21 dpa, fish were challenged with Aeromonas hydrophila and mortality was recorded for 14 days. Immune parameters such as lysozyme levels (39.29 ± 2.14 U mL-1), alternative complement pathway (61.21 ± 2.38 U mL-1), and phagocytic activities (33.37 ± 1.2%) were maximum (P Biosurfactant was effective in inhibiting biofilm formation up to 54.71 ± 1.27%. Moreover, it efficiently removed cadmium (Cd) from tested vegetables such as carrot, radish, ginger, and potato, with the highest removal efficiency (60.98 ± 1.29%) recorded in ginger contaminated with Cd. Collectively, these results suggest that isolated biosurfactant could be used in the aquaculture industry, in addition to its potential application to the food industry. PMID:28400765

Effect of medium components on the production of a biosurfactant from Candida tropicalis applied to the removal of hydrophobic contaminants in soil.

Science.gov (United States)

Batista, Ranielly M; Rufino, Raquel D; Luna, Juliana M; de Souza, José Edson G; Sarubbo, Leonie A

2010-05-01

The influence of medium constituents on the production of biosurfactants by Candida tropicalis cultivated in waste frying oil was investigated according to a fractional factorial 2(5-1) design. The combined effect of the C/N(inorganic), C/Fe, C/Mg, and C/P ratios and yeast extract on surface tension reduction, biosurfactant yield, emulsification activity, and biomass were studied. The highest biosurfactant yield was reached when low C/Mg and low C/P ratio variables were combined, while the cell growth was favored by increasing the nitrogen concentration. The highest surface tension net decrease, on the other hand, was observed at low yeast extract concentration, low C/Fe, and high C/P ratios. Emulsification indices against lubrication and automobile waste oil of approximately 65 to 95% were observed. The crude biosurfactant produced in the medium--formulated with 2% waste frying oil, 0.067% NH4Cl, 0.025% MgSO4.7H2O, 0.067% KH2PO4, and 0.0026% FeCl3.6H2O--removed approximately 78 to 97% of the petroleum and motor oil adsorbed in sand samples.

Isolation and characterization of biosurfactant production under extreme environmental conditions by alkali-halo-thermophilic bacteria from Saudi Arabia.

Science.gov (United States)

Elazzazy, Ahmed M; Abdelmoneim, T S; Almaghrabi, O A

2015-07-01

Twenty three morphologically distinct microbial colonies were isolated from soil and sea water samples, which were collected from Jeddah region, Saudi Arabia for screening of the most potent biosurfactant strains. The isolated bacteria were selected by using different methods as drop collapse test, oil displacement test, blue agar test, blood hemolysis test, emulsification activity and surface tension. The results showed that the ability of Virgibacillus salarius to grow and reduce surface tension under a wide range of pH, salinities and temperatures gives bacteria isolate an advantage in many applications such as pharmaceutical, cosmetics, food industries and bioremediation in marine environment. The biosurfactant production by V. salarius decreased surface tension and emulsifying activity (30 mN/m and 80%, respectively). In addition to reducing the production cost of biosurfactants by tested several plant-derived oils such as jatropha oil, castor oils, jojoba oil, canola oil and cottonseed oil. In this respect the feasibility to reusing old frying oil of sunflower for production rhamnolipids and sophorolipids, their use that lead to solve many ecological and industrial problems.

Stimulation of rhamnolipid biosurfactants production in Pseudomonas aeruginosa AK6U by organosulfur compounds provided as sulfur sources.

Science.gov (United States)

Ismail, Wael; Shammary, Sultanah Al; El-Sayed, Wael S; Obuekwe, Christian; El Nayal, Ashraf M; Abdul Raheem, Abdul Salam; Al-Humam, Abdulmohsen

2015-09-01

A Pseudomonas aeruginosa AK6U strain produced rhamnolipid biosurfactants to variable extents when grown on MgSO 4 or organosulfur compounds as sulfur sources and glucose as a carbon source. Organosulfur cultures produced much higher biosurfactants amounts compared to the MgSO 4 cultures. The surface tension of the growth medium was reduced from 72 mN/m to 54 and 30 mN/m in cultures containing MgSO 4 and 4,6-dimethyldibenzothiophene (4,6-DM-DBT), respectively. AK6U cultures produced different rhamnolipid congener profiles depending on the provided sulfur source. The dibenzothiophene (DBT) culture produced more diverse and a higher number of rhamnolipid congeners as compared to the DBT-sulfone and MgSO 4 cultures. The number of mono-rhamnolipid congeners in the DBT culture was also higher than that detected in the DBT-sulfone and MgSO 4 cultures. Di-rhamnolipids dominated the congener profiles in all the analyzed cultures. The sulfur source can have a profound impact on the quality and quantity of the produced biosurfactants.

Isolation and characterization of biosurfactant production under extreme environmental conditions by alkali-halo-thermophilic bacteria from Saudi Arabia

Science.gov (United States)

Elazzazy, Ahmed M.; Abdelmoneim, T.S.; Almaghrabi, O.A.

2014-01-01

Twenty three morphologically distinct microbial colonies were isolated from soil and sea water samples, which were collected from Jeddah region, Saudi Arabia for screening of the most potent biosurfactant strains. The isolated bacteria were selected by using different methods as drop collapse test, oil displacement test, blue agar test, blood hemolysis test, emulsification activity and surface tension. The results showed that the ability of Virgibacillus salarius to grow and reduce surface tension under a wide range of pH, salinities and temperatures gives bacteria isolate an advantage in many applications such as pharmaceutical, cosmetics, food industries and bioremediation in marine environment. The biosurfactant production by V. salarius decreased surface tension and emulsifying activity (30 mN/m and 80%, respectively). In addition to reducing the production cost of biosurfactants by tested several plant-derived oils such as jatropha oil, castor oils, jojoba oil, canola oil and cottonseed oil. In this respect the feasibility to reusing old frying oil of sunflower for production rhamnolipids and sophorolipids, their use that lead to solve many ecological and industrial problems. PMID:26150754

Stimulation of rhamnolipid biosurfactants production in Pseudomonas aeruginosa AK6U by organosulfur compounds provided as sulfur sources

Directory of Open Access Journals (Sweden)

Wael Ismail

2015-09-01

Full Text Available A Pseudomonas aeruginosa AK6U strain produced rhamnolipid biosurfactants to variable extents when grown on MgSO4 or organosulfur compounds as sulfur sources and glucose as a carbon source. Organosulfur cultures produced much higher biosurfactants amounts compared to the MgSO4 cultures. The surface tension of the growth medium was reduced from 72 mN/m to 54 and 30 mN/m in cultures containing MgSO4 and 4,6-dimethyldibenzothiophene (4,6-DM-DBT, respectively. AK6U cultures produced different rhamnolipid congener profiles depending on the provided sulfur source. The dibenzothiophene (DBT culture produced more diverse and a higher number of rhamnolipid congeners as compared to the DBT-sulfone and MgSO4 cultures. The number of mono-rhamnolipid congeners in the DBT culture was also higher than that detected in the DBT-sulfone and MgSO4 cultures. Di-rhamnolipids dominated the congener profiles in all the analyzed cultures. The sulfur source can have a profound impact on the quality and quantity of the produced biosurfactants.

Vegetable processing wastes addition to improve swine manure anaerobic digestion: Evaluation in terms of methane yield and SEM characterization

International Nuclear Information System (INIS)

Molinuevo-Salces, Beatriz; González-Fernández, Cristina; Gómez, Xiomar; García-González, María Cruz; Morán, Antonio

2012-01-01

Highlights: ► Vegetable waste as co-substrate for swine manure anaerobic digestion. ► Two hydraulic retention times of 25 and 15 d, respectively. ► SEM characterization of anaerobic sludges to observe microbial composition. ► Vegetable waste as co-substrate increases methane yields up to three times. ► Microbial composition changes after 120 d of digestion. -- Abstract: The effect of adding vegetable waste as a co-substrate in the anaerobic digestion of swine manure was investigated. The study was carried out at laboratory scale using semi-continuous stirred tank reactors working at 37 °C. Organic loading rates (OLRs) of 0.4 and 0.6 g VS L −1 d −1 were evaluated, corresponding to hydraulic retention times (HRTs) of 25 and 15 d, respectively. The addition of vegetable wastes (50% dw/dw) resulted in an improvement of 3 and 1.4-fold in methane yields at HRTs of 25 and 15 d, respectively. Changes on microbial morphotypes were studied by Scanning Electron Microscopy (SEM). Samples analyzed were sludge used as inoculum and digestate obtained from swine manure anaerobic reactors. SEM pictures demonstrated that lignocellulosic material was not completely degraded. Additionally, microbial composition was found to change to cocci and rods morphotypes after 120 d of anaerobic digestion.

Improvement of anaerobic bio-hydrogen gas production from organic sludge waste

International Nuclear Information System (INIS)

Lee, S.; Lee, Y. H.

2009-01-01

Microbial hydrogen gas production from organic matters stands out as one of the most promising alternatives for sustainable green energy production. Based on the literature review, investigation of anaerobic bio-hydrogen gas production from organic sludge waste using a mixed culture has been very limited. The objective of this study was to assess the anaerobic bio-hydrogen gas production from organic sludge waste under various conditions. (Author)

Efficacy of a Ventilatory Training Mask to Improve Anaerobic and Aerobic Capacity in Reserve Officers' Training Corps Cadets.

Science.gov (United States)

Sellers, John H; Monaghan, Taylor P; Schnaiter, Jessica A; Jacobson, Bert H; Pope, Zachary K

2016-04-01

The purpose of this study was to examine the efficacy of a ventilatory training mask to improve anaerobic and aerobic fitness in reserve officers' training corps (ROTC) cadets. Seventeen ROTC cadets from a Midwest university completed pre- and postassessments consisting of anthropometry, a 30-second Wingate Anaerobic Test (WAnT), and a maximal aerobic capacity test (V[Combining Dot Above]O2max). A 6-week intervention training period was used during which time participants completed their mandatory physical training (PT) sessions. Participants were randomly assigned to either the experimental group (MASK; n = 9) or the control group (CON; n = 8). The ventilatory training masks were adjusted to simulate an altitude of 2,750 m. There was no significant effect (p ≤ 0.05) between groups on fatigue index, anaerobic capacity, peak power, V[Combining Dot Above]O2max, or time to exhaustion. These results suggest that the use of the ventilatory training mask during mandatory PT did not elicit superior aerobic or anaerobic adaptations in ROTC cadets. Therefore, it is recommended that more established simulated altitude training methods be used when incorporating intermittent hypoxic training.

Biosurfactant assisted synthesis of Fe3O4@rhamnolipid@BiOBr and its behaviour in plasma discharge system

Science.gov (United States)

Wang, Li; Yu, Zebin; Hou, Yanping; Peng, Zhenbo; Zhang, Li; Meng, Zhengcheng; Li, Fengyuan; He, Jun; Huang, Junlin

2016-06-01

A novel Fe3O4@rhamnolipid@BiOBr (FRB) was synthesized via a modified precipitation method and applied in the plasma discharge system. Rhamnolipid was used as biosurfactant to modify Fe3O4 by interacting with Fe3O4 via its aliphatic chain. The results show that the prepared FRB magnetic photocatalyst exhibited excellent photocatalytic activity and Fenton reaction behavior in the plasma discharge system. Meanwhile, the addition of FRB could improve energy efficiency of defluorination by 21.29 mg kW-1 h-1.

Biosurfactant assisted synthesis of Fe3O4@rhamnolipid@BiOBr and its behaviour in plasma discharge system

International Nuclear Information System (INIS)

Wang, Li; Yu, Zebin; Hou, Yanping; Peng, Zhenbo; Zhang, Li; Meng, Zhengcheng; Li, Fengyuan; He, Jun; Huang, Junlin

2016-01-01

A novel Fe 3 O 4 @rhamnolipid@BiOBr (FRB) was synthesized via a modified precipitation method and applied in the plasma discharge system. Rhamnolipid was used as biosurfactant to modify Fe 3 O 4 by interacting with Fe 3 O 4 via its aliphatic chain. The results show that the prepared FRB magnetic photocatalyst exhibited excellent photocatalytic activity and Fenton reaction behavior in the plasma discharge system. Meanwhile, the addition of FRB could improve energy efficiency of defluorination by 21.29 mg kW −1 h −1 . (paper)

Selective cultures for the isolation of biosurfactant producing bacteria: comparison of different combinations of environmental inocula and hydrophobic carbon sources.

Science.gov (United States)

Domingues, Patrícia M; Louvado, António; Oliveira, Vanessa; Coelho, Francisco J C R; Almeida, Adelaide; Gomes, Newton C M; Cunha, Angela

2013-01-01

The potential of estuarine microniches as reservoirs of biosurfactant-producing bacteria was evaluated by testing different combinations of inocula and hydrophobic carbon sources. Selective cultures using diesel, petroleum, or paraffin as hydrophobic carbon sources were prepared and inoculated with water from the surface microlayer, bulk sediments, and sediment of the rhizosphere of Halimione portulacoides. These inocula were compared regarding the frequency of biosurfactant-producing strains among selected isolates. The community structure of the selective cultures was profiled using denaturing gradient gel electrophoresis (DGGE) of the 16S rRNA gene fragments at the end of the incubation. The DGGE profiles corresponding to the communities established in selective cultures at the end of the incubation revealed that communities were different in terms of structural diversity. The highest diversity was observed in the selective cultures containing paraffin (H (') = 2.5). Isolates were obtained from the selective cultures (66) and tested for biosurfactant production by the atomized oil assay. Biosurfactant production was detected in 17 isolates identified as Microbacterium, Pseudomonas, Rhodococcus, and Serratia. The combination of estuarine surface microlayer (SML) water as inoculum and diesel as carbon source seems promising for the isolation of surfactant-producing bacteria. Supplemental materials are available for this article. Go to the publisher's online edition of Preparative Biochemistry and Biotechnology to view the supplemental file.

Biosurfactant-and-bioemulsifier produced by a promising Cunninghamella echinulata isolated from Caatinga soil in the northeast of Brazil.

Science.gov (United States)

Andrade Silva, Nadielly R; Luna, Marcos A C; Santiago, André L C M A; Franco, Luciana O; Silva, Grayce K B; de Souza, Patrícia M; Okada, Kaoru; Albuquerque, Clarissa D C; da Silva, Carlos A Alves; Campos-Takaki, Galba M

2014-09-01

A Mucoralean fungus was isolated from Caatinga soil of Pernambuco, Northeast of Brazil, and was identified as Cunninghamella echinulata by morphological, physiological, and biochemical tests. This strain was evaluated for biosurfactant/bioemulsifier production using soybean oil waste (SOW) and corn steep liquor (CSL) as substrates, added to basic saline solution, by measuring surface tension and emulsifier index and activity. The best results showed the surface water tension was reduced from 72 to 36 mN/m, and an emulsification index (E₂₄) of 80% was obtained using engine oil and burnt engine oil, respectively. A new molecule of biosurfactant showed an anionic charge and a polymeric chemical composition consisting of lipids (40.0% w/w), carbohydrates (35.2% w/w) and protein (20.3% w/w). In addition, the biosurfactant solution (1%) demonstrated its ability for an oil displacement area (ODA) of 37.36 cm², which is quite similar to that for Triton X-100 (38.46 cm²). The stability of the reduction in the surface water tension as well as of the emulsifier index proved to be stable over a wide range of temperatures, in pH, and in salt concentration (4%-6% w/v). The biosurfactant showed an ability to reduce and increase the viscosity of hydrophobic substrates and their molecules, suggesting that it is a suitable candidate for mediated enhanced oil recovery. At the same time, these studies indicate that renewable, relatively inexpensive and easily available resources can be used for important biotechnological processes.

New Transfection Agents Based on Liposomes Containing Biosurfactant MEL-A

Directory of Open Access Journals (Sweden)

Tadahide Furuno

2013-08-01

Full Text Available Nano vectors are useful tools to deliver foreign DNAs, oligonucleotides, and small interfering double-stranded RNAs (siRNAs into mammalian cells with gene transfection and gene regulation. In such experiments we have found the liposomes with a biosurfacant mannosylerythriol lipid (MEL-A are useful because of their high transfer efficiency, and their unique mechanism to transfer genes to target cells with the lowest toxicity. In the present review we will describe our current work, which may contribute to the great advance of gene transfer to target cells and gene regulations. For more than two decades, the liposome technologies have changed dramatically and various methods have been proposed in the fields of biochemistry, cell biology, biotechnology, and so on. In addition, they were towards to pharmaceutics and clinical applications. The liposome technologies were expected to use gene therapy, however, they have not reached a requested goal as of yet. In the present paper we would like to present an approach using a biosurfactant, MEL-A, which is a surface-active compound produced by microorganisms growing on water-insoluble substrates and increases efficiency in gene transfection. The present work shows new transfection agents based on liposomes containing biosurfactant MEL-A.

Biosurfactants produced by Scheffersomyces stipitis cultured in sugarcane bagasse hydrolysate as new green larvicides for the control of Aedes aegypti, a vector of neglected tropical diseases.

Science.gov (United States)

Franco Marcelino, Paulo Ricardo; da Silva, Vinícius Luiz; Rodrigues Philippini, Rafael; Von Zuben, Cláudio José; Contiero, Jonas; Dos Santos, Júlio César; da Silva, Silvio Silvério

2017-01-01

Biosurfactants are microbial metabolites with possible applications in various industrial sectors that are considered ecofriendly molecules. In recent years, some studies identified these compounds as alternatives for the elimination of vectors of tropical diseases, such as Aedes aegypti. The major bottlenecks of biosurfactant industrial production have been the use of conventional raw materials that increase production costs as well as opportunistic or pathogenic bacteria, which restrict the application of these biomolecules. The present study shows the potential of hemicellulosic sugarcane bagasse hydrolysate as a raw material for the production of a crystalline glycolipidic BS by Scheffersomyces stipitis NRRL Y-7124, which resulted in an emulsifying index (EI24) of 70 ± 3.4% and a superficial tension of 52 ± 2.9 mN.m-1. Additionally, a possible new application of these compounds as biolarvicides, mainly against A. aegypti, was evaluated. At a concentration of 800 mg.L-1, the produced biosurfactant caused destruction to the larval exoskeletons 12 h after application and presented an letal concentration (LC50) of 660 mg.L-1. Thus, a new alternative for biosurfactant production using vegetal biomass as raw material within the concept of biorefineries was proposed, and the potential of the crystalline glycolipidic biosurfactant in larvicidal formulations against neglected tropical disease vectors was demonstrated.

The hydrocarbon-degrading marine bacterium Cobetia sp. strain MM1IDA2H-1 produces a biosurfactant that interferes with quorum sensing of fish pathogens by signal hijacking

Science.gov (United States)

Ibacache-Quiroga, C; Ojeda, J; Espinoza-Vergara, G; Olivero, P; Cuellar, M; Dinamarca, M A

2013-01-01

Summary Biosurfactants are produced by hydrocarbon-degrading marine bacteria in response to the presence of water-insoluble hydrocarbons. This is believed to facilitate the uptake of hydrocarbons by bacteria. However, these diffusible amphiphilic surface-active molecules are involved in several other biological functions such as microbial competition and intra-or inter-species communication. We report the isolation and characterization of a marine bacterial strain identified as Cobetia sp. MM1IDA2H-1, which can grow using the sulfur-containing heterocyclic aromatic hydrocarbon dibenzothiophene (DBT). As with DBT, when the isolated strain is grown in the presence of a microbial competitor, it produces a biosurfactant. Because the obtained biosurfactant was formed by hydroxy fatty acids and extracellular lipidic structures were observed during bacterial growth, we investigated whether the biosurfactant at its critical micelle concentration can interfere with bacterial communication systems such as quorum sensing. We focused on Aeromonas salmonicida subsp. salmonicida, a fish pathogen whose virulence relies on quorum sensing signals. Using biosensors for quorum sensing based on Chromobacterium violaceum and Vibrio anguillarum, we showed that when the purified biosurfactant was mixed with N-acyl homoserine lactones produced by A. salmonicida, quorum sensing was inhibited, although bacterial growth was not affected. In addition, the transcriptional activities of A. salmonicida virulence genes that are controlled by quorum sensing were repressed by both the purified biosurfactant and the growth in the presence of Cobetia sp. MM1IDA2H-1. We propose that the biosurfactant, or the lipid structures interact with the N-acyl homoserine lactones, inhibiting their function. This could be used as a strategy to interfere with the quorum sensing systems of bacterial fish pathogens, which represents an attractive alternative to classical antimicrobial therapies in fish

Improved production, purification, and characterization of biosurfactants produced by Serratia marcescens SM3 and its isogenic SMRG-5 strain.

Science.gov (United States)

Rosas-Galván, Nashbly Sarela; Martínez-Morales, Fernando; Marquina-Bahena, Silvia; Tinoco-Valencia, Raunel; Serrano-Carreón, Leobardo; Bertrand, Brandt; León-Rodríguez, Renato; Guzmán-Aparicio, Josefina; Alvaréz-Berber, Laura; Trejo-Hernández, María R

2018-02-19

In this study, the biosurfactants (Bs) production of two Serratia marcescens strains (SM3 and its isogenic SMRG-5 strain) was improved and the tenso-active agents were purified and characterized. A 2 3 factorial design was used to evaluate the effect of nitrogen and carbon sources on the surface tension (ST) reduction and emulsion index (EI 24 ) of the produced Bs. Optimum Bs production by SM3 was achieved at high concentrations of carbon and nitrogen, reducing ST to 26.5 ± 0.28 dynes/cm, with an EI 24 of 79.9 ± 0.2%. Meanwhile, the best results for SMRG-5 were obtained at low concentrations, reducing the ST to 25.2 ± 0.2 dynes/cm, with an EI 24 of 89.7 ± 0.28%. The optimal conditions for Bs production were scaled up in a 2-L reactor, yielding 4.8 and 5.2 g/L for SM3 and SMRG-5, respectively. Gas Chromatography-Mass Spectrometry (GC-MS) analysis revealed the presence of two different lipopeptides (hidrofobic fractions: octadecanoic and hexadecanoic acid for SM3 and SMRG5, respectively). Both strains were capable of benzo [a] pyrene removal (59% after 72 H of culture). © 2018 International Union of Biochemistry and Molecular Biology, Inc.

Production of biosurfactants for environment remediation contaminated with oil and derivatives; Producao de biossurfactantes para remediacao de ambiente contaminados com petroleo e derivados

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Adriano Henrique Soares de; Guimaraes, Juliana Aguilar; Hiluy Filho, Joao Jose; Lopes, Ada Amelia Sanders [Universidade Federal do Ceara, Fortaleza, CE (Brazil). Dept. de Engenharia Quimica]. E-mail: hiluy@ufc.br

2003-07-01

Biosurfactants are emulsifiers of hydrocarbons produced by bacteria, yeast and fungi. They are polymers that form micelles and stay at the interface between liquid of different polarities. This work aim to study the development of the biosurfactant production process and its application related to oil sludge. This research has been done in three different steps: the Acinetobacter iwoffii inoculation, its growth in a nutritive broth and the fermentation under specific conditions. It was used three different kind of substrates: ethanol, glycerol and kerosene for comparison. The surfactant potential was evaluated by the emulsification indexes with suspension biomass and efficiency tests with oil sludge. Preliminary results show that biosurfactant production by Acinetobacter iwoffii can be a feasible process due to the satisfactory emulsification indexes that have been obtained. (author)

Effects of biosurfactant production by indigenous soil microorganisms on bioremediation of a co-contaminated soil in batch experiments

Energy Technology Data Exchange (ETDEWEB)

Jalali, F.; Mulligan, C.N. [Concordia Univ., Centre for Building Studies, Montreal, PQ (Canada). Dept. of Building, Civil and Environmental Engineering

2007-07-01

The challenge of remediating soils that are contaminated with both hydrocarbon compounds and metals was discussed, with particular reference to an in-situ bioremediation technique that was developed in the 1970s to deal with contaminated soils. The technique involves a two-stage process where water with added oxygen and nutrients is applied onto and injected into a contaminated area to stimulate the indigenous microbial populations in the soil. In addition to using organic pollutants as their carbon source, microorganisms can facilitate the removal of metals from the soil matrix and attenuate the toxicity of certain metals. Extraction wells placed downstream of the contaminated soils are used to remove and treat the water to eliminate any mobilized contaminants. This paper presented the results of batch experiments that evaluated the feasibility of biosurfactant production for the purpose of bioremediating a soil contaminated with aged petroleum hydrocarbons and heavy metals. The first phase of the study examined the growth of the native microbial population and the biodegradation of petroleum hydrocarbons, the production of biosurfactant and the mobilization of the total petroleum hydrocarbons (TPH) and metals into the aqueous phase. Biodegradation of petroleum hydrocarbons was observed in both soil and soil amended with nitrogen and phosphorous. However, the nutrient-amended soil had higher biodegradation of petroleum hydrocarbons, where 36 per cent of TPH was degraded by the end of the 50 day experiment, compared to 15 per cent for the non-amended soils. The concentration of biosurfactants in the same period increased 3 times their critical micelle concentration. It was concluded that biosurfactant production enhances the bioremediation of co-contaminated soils. 36 refs., 1 tab., 8 figs.

Green synthesis and characterization of cuprous oxide nanoparticles in presence of a bio-surfactant

Science.gov (United States)

Behera, M.; Giri, G.

2014-12-01

Herein, we report a facile green synthesis of Cu2O nanoparticles (NPs) using copper sulfate as precursor salt and hydrazine hydrate as reducing agent in presence of bio-surfactant (i.e. leaves extract of arka — a perennial shrub) at 60 to 70 °C in an aqueous medium. A broad band centered at 460 nm in absorption spectrum reveals the formation of surfactant stabilized Cu2O NPs. X-ray diffraction pattern of the surfactant stabilized NPs suggests the formation of only Cu2O phase in assistance of a bio-surfactant with the crystallite size of ˜8 nm. A negative zeta potential of -12 mV at 8.0 pH in surfactant stabilized Cu2O NPs hints non-bonding electron transfer from O-atom of saponin to the surface of NP. Red-shift in the vibrational band (Cu-O stretching) of Cu2O from 637 cm-1 to 640 cm-1 in presence of bio-surfactant suggests an interfacial interaction between NPs and O-atoms of -OH groups of saponin present in the plant (i.e. Calotropis gigantean) extract. From X-ray photoelectron spectroscopy spectra, a decrease in binding energy of both 2p3/2 and 2p1/2 bands in Cu2O with saponin molecules as compared to bulk Cu atom reveals a charge transfer interaction between NP and saponin surfactant molecules. Transmission electron microscopy images show crystalline nature of Cu2O NPs with an fcc lattice.

Biosurfactants produced by Scheffersomyces stipitis cultured in sugarcane bagasse hydrolysate as new green larvicides for the control of Aedes aegypti, a vector of neglected tropical diseases.

Directory of Open Access Journals (Sweden)

Paulo Ricardo Franco Marcelino

Full Text Available Biosurfactants are microbial metabolites with possible applications in various industrial sectors that are considered ecofriendly molecules. In recent years, some studies identified these compounds as alternatives for the elimination of vectors of tropical diseases, such as Aedes aegypti. The major bottlenecks of biosurfactant industrial production have been the use of conventional raw materials that increase production costs as well as opportunistic or pathogenic bacteria, which restrict the application of these biomolecules. The present study shows the potential of hemicellulosic sugarcane bagasse hydrolysate as a raw material for the production of a crystalline glycolipidic BS by Scheffersomyces stipitis NRRL Y-7124, which resulted in an emulsifying index (EI24 of 70 ± 3.4% and a superficial tension of 52 ± 2.9 mN.m-1. Additionally, a possible new application of these compounds as biolarvicides, mainly against A. aegypti, was evaluated. At a concentration of 800 mg.L-1, the produced biosurfactant caused destruction to the larval exoskeletons 12 h after application and presented an letal concentration (LC50 of 660 mg.L-1. Thus, a new alternative for biosurfactant production using vegetal biomass as raw material within the concept of biorefineries was proposed, and the potential of the crystalline glycolipidic biosurfactant in larvicidal formulations against neglected tropical disease vectors was demonstrated.

Structural characterization of novel sophorolipid biosurfactants from a newly-identified species of Candida yeast

Science.gov (United States)

The sophorolipids are a group of O-acylsophorose-based biosurfactants produced by several yeasts of the Starmerella clade. The known sophorolipids are typically partially acetylated 2-O-ß-D-glucopyranosyl-D-glucopyranose (sophorose) ß-O-glycosidically-linked to 17-L-hydroxy-delta-9-octadecenoic aci...

Bile anaerobic bacteria detection and antibiotic susceptibility in patients with gallstone.

Science.gov (United States)

Lu, Yun; Xiang, Ting-Hai; Shi, Jing-Sen; Zhang, Bing-Yuan

2003-08-01

To detect bile anaerobic bacteria and antibiotic susceptibility in 59 patients with gallstones who had had cholecystectomy. BACT/ALERT 120 microbe detection system and SCEPTOR microbe detection system were used to detect bile anaerobic bacteria, antibiotic susceptibility. The ratio of anaerobic bacteria to the patients examined was 52.5% (31/59). Obligate anaerobe bile culture showed positive results in 4 patients. B. fragilis (37.8%) was the major type of anaerobic bacteria in bile. Most (81.8%) of anaerobic bacteria were sensitive to metronidazole, and imipenem was suitable for beta-lactamase bacteria. Culture of anaerobic bacteria in logarithmic phase can improve the positive rate of the culture. There are some relations between anaerobic infection and gallstone formation.

The efficacy of Poly-β-Hydroxy Butyrate (PHB)/biosurfactant derived from Staphylococcus hominis against White Spot Syndrome Virus (WSSV) in Penaeus monodon.

Science.gov (United States)

Monica, M; Priyanka, T; Akshaya, Murugesan; Rajeswari, V; Sivakumar, Lingappa; Somasundaram, S T; Shenbhagarathai, R

2017-12-01

White Spot Syndrome Virus (WSSV) is one of the most important causative agents of Penaeid shrimps diseases that incur heavy losses to the shrimp aquaculture. It has severe impact on the sustainability and the production of Penaeus monodon. Hence, the present study focussed on the investigation of Poly-β-hydroxybutyrate/biosurfactant as immunostimulants against WSSV infected shrimps. Infection of WSSV was periodically checked in all the experimental shrimps using PCR diagnostic kit. After ensuring all shrimps were free of viral infection, experiments were carried out to analyze the nonspecific immune responses (prophenol oxidase, nitro blue tetrazolium reduction assay and total haemocyte count) both in control and experimental group. Further, gills and muscles of Penaeus monodon were subjected to proteome analysis after treated it with PHB/biosurfactant independently in the concentration of 2% and 5% each. Increase in the level of haemocytes was observed in both PHB (26 ± 2 × 10⁴ cells)/biosurfactant (28 ± 2 × 10 4  cells) treated shrimps, when compared with control (17 ± 2 × 10⁴ cells). proPhenolOxidase (proPO) activity was also enhanced in treated groups compared to WSSV infected shrimps. Less production of superoxide anion was observed in control and treated groups. Differences in the protein expression was analyzed in muscle tissue of control, WSSV infected and PHB/biosurfactant treated shrimps. Our finding suggested that partial substitution of feed with 2% PHB and biosurfactant showed increased rate on the survival of WSSV infected P. monodon which might be due to either the over expression/down regulation of proteins that play a vital role in enhancing the immune system/the progression of the disease respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Diversity and activity of biosurfactant-producing Pseudomonas in the rhizosphere of black pepper in Vietnam

NARCIS (Netherlands)

Tran, H.; Kruijt, M.; Raaijmakers, J.M.

2008-01-01

Aims: Phytophthora capsici is a major pathogen of black pepper and zoospores play an important role in the infection process. Fluorescent pseudomonads that produce biosurfactants with zoosporicidal activities were isolated from the black pepper rhizosphere in Vietnam, and their genotypic diversity

[Anaerobic bacteria isolated from patients with suspected anaerobic infections].

Science.gov (United States)

Ercis, Serpil; Tunçkanat, Ferda; Hasçelik, Gülşen

2005-10-01

The study involved 394 clinical samples sent to the Clinical Microbiology Laboratory of Hacettepe University Adult Hospital between January 1997 and May 2004 for anaerobic cultivation. Since multiple cultures from the same clinical samples of the same patient were excluded, the study was carried on 367 samples. The anaerobic cultures were performed in anaerobic jar using AnaeroGen kits (Oxoid, Basingstoke, U.K.) or GENbox (bioMérieux, Lyon, France). The isolates were identified by both classical methods and "BBL Crystal System" (Becton Dickinson, U.S.A.). While no growth was detected in 120 (32.7%) of the clinical samples studied, in 144 samples (39.2%) only aerobes, in 28 (7.6%) only anaerobes and in 75 (20.5%) of the samples both aerobes and anaerobes were isolated. The number of the anaerobic isolates was 217 from 103 samples with anaerobic growth. Of these 103 samples 15 showed single bacterial growth whereas in 88 samples multiple bacterial isolates were detected. Anaerobic isolates consisted of 92 Gram negative bacilli (Bacteroides spp. 50, Prevotella spp. 14, Porphyromonas spp. 10, Fusobacterium spp. 7, Tisierella spp. 2, unidentified 9), 57 Gram positive bacilli (Clostridium spp.17, Propionibacterium spp. 16, Lactobacillus spp. 8, Actinomyces spp. 5, Eubacterium spp. 2, Bifidobacterium adolescentis 1, Mobiluncus mulieris 1, unidentified nonspore forming rods 7), 61 Gram positive cocci (anaerobic cocci 44, microaerophilic cocci 17), and 7 Gram negative cocci (Veillonella spp.). In conclusion, in the samples studied with prediagnosis of anaerobic infection, Bacteroides spp. (23%) were the most common bacteria followed by anaerobic Gram positive cocci (20.3%) and Clostridium spp (7.8%).

BIODEGRADATION OF PETROLEUM-WASTE BY BIOSURFACTANT-PRODUCING BACTERIA

Energy Technology Data Exchange (ETDEWEB)

Brigmon, R; Grazyna A. Plaza, G; Kamlesh Jangid, K; Krystyna Lukasik, K; Grzegorz Nalecz-Jawecki, G; Topher Berry, T

2007-05-16

The degradation of petroleum waste by mixed bacterial cultures which produce biosurfactants: Ralstonia pickettii SRS (BP-20), Alcaligenes piechaudii SRS (CZOR L-1B), Bacillus subtilis (1'- 1a), Bacillus sp. (T-1) and Bacillus sp. (T'-1) was investigated. The total petroleum hydrocarbons were degraded substantially (91 %) by the mixed bacterial culture in 30 days (reaching up to 29 % in the first 72 h). Similarly, the toxicity of the biodegraded petroleum waste decreased 3 times after 30 days as compared to raw petroleum waste. Thus, the mixed bacterial strains effectively clean-up the petroleum waste and they can be used in other bioremediation processes.

Glycolipid biosurfactants: main properties and potential applications in agriculture and food industry.

Science.gov (United States)

Mnif, Inès; Ghribi, Dhouha

2016-10-01

Glycolipids, consisting of a carbohydrate moiety linked to fatty acids, are microbial surface active compounds produced by various microorganisms. They are characterized by high structural diversity and have the ability to decrease the surface and interfacial tension at the surface and interface, respectively. Rhamnolipids, trehalolipids, mannosylerythritol lipids and cellobiose lipids are among the most popular glycolipids. They have received much practical attention as biopesticides for controlling plant diseases and protecting stored products. As a result of their antifungal activity towards phytopathogenic fungi and larvicidal and mosquitocidal potencies, glycolipid biosurfactants permit the preservation of plants and plant crops from pest invasion. Also, as a result of their emulsifying and antibacterial activities, glycolipids have great potential as food additives and food preservatives. Furthermore, the valorization of food byproducts via the production of glycolipid biosurfactant has received much attention because it permits the bioconversion of byproducts on valuable compounds and decreases the cost of production. Generally, the use of glycolipids in many fields requires their retention from fermentation media. Accordingly, different strategies have been developed to extract and purify glycolipids. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

In situ biosurfactant production and hydrocarbon removal by Pseudomonas putida CB-100 in bioaugmented and biostimulated oil-contaminated soil

Directory of Open Access Journals (Sweden)

Martínez-Toledo Ángeles

2013-01-01

Full Text Available In situ biosurfactant (rhamnolipid production by Pseudomonas putida CB-100 was achieved during a bioaugmented and biostimulated treatment to remove hydrocarbons from aged contaminated soil from oil well drilling operations. Rhamnolipid production and contaminant removal were determined for several treatments of irradiated and non-irradiated soils: nutrient addition (nitrogen and phosphorus, P. putida addition, and addition of both (P. putida and nutrients. The results were compared against a control treatment that consisted of adding only sterilized water to the soils. In treatment with native microorganisms (non-irradiated soils supplemented with P. putida, the removal of total petroleum hydrocarbons (TPH was 40.6%, the rhamnolipid production was 1.54 mg/kg, and a surface tension of 64 mN/m was observed as well as a negative correlation (R = -0.54; p < 0.019 between TPH concentration (mg/kg and surface tension (mN/m, When both bacteria and nutrients were involved, TPH levels were lowered to 33.7%, and biosurfactant production and surface tension were 2.03 mg/kg and 67.3 mN/m, respectively. In irradiated soil treated with P. putida, TPH removal was 24.5% with rhamnolipid generation of 1.79 mg/kg and 65.6 mN/m of surface tension, and a correlation between bacterial growth and biosurfactant production (R = -0.64; p < 0.009 was observed. When the nutrients and P. putida were added, TPH removal was 61.1%, 1.85 mg/kg of biosurfactants were produced, and the surface tension was 55.6 mN/m. In summary, in irradiated and non-irradiated soils, in situ rhamnolipid production by P. putida enhanced TPH decontamination of the soil.

Using natural zeolites to improve anaerobic abattoir wastewater treatment

International Nuclear Information System (INIS)

Diaz-Jimenez, L.; Herrera-Ramirez, E.; Carlos Hernandez, S

2009-01-01

Slaughterhouse wastewater have high concentrations of soluble and insoluble organics which represents environmental troubles, E. G. de oxygenation of rivers, underground water contamination. Anaerobic digestion is an efficient process for wastewater treatment. Performance are increased using microorganisms supported on porous solids. (Author)

Using natural zeolites to improve anaerobic abattoir wastewater treatment

Energy Technology Data Exchange (ETDEWEB)

Diaz-Jimenez, L.; Herrera-Ramirez, E.; Carlos Hernandez, S

2009-07-01

Slaughterhouse wastewater have high concentrations of soluble and insoluble organics which represents environmental troubles, E. G. de oxygenation of rivers, underground water contamination. Anaerobic digestion is an efficient process for wastewater treatment. Performance are increased using microorganisms supported on porous solids. (Author)

Synthesis of silver nanoparticles using a biosurfactant produced in low-cost medium as stabilizing agent

Directory of Open Access Journals (Sweden)

Charles B.B. Farias

2014-05-01

Conclusions: This process provided a simpler route for nanoparticle synthesis compared to existing systems using whole organisms or partially purified biological extracts, showing that the low-cost biosurfactant can be used for nanoparticle synthesis as a non-toxic and biodegradable stabilizing agent.

Biogeographical distribution analysis of hydrocarbon degrading and biosurfactant producing genes suggests that near-equatorial biomes have higher abundance of genes with potential for bioremediation

OpenAIRE

Oliveira, Jorge S.; Ara?jo, Wydemberg J.; Figueiredo, Ricardo M.; Silva-Portela, Rita C. B.; de Brito Guerra, Alaine; da Silva Ara?jo, Sinara Carla; Minnicelli, Carolina; Carlos, Aline Cardoso; de Vasconcelos, Ana Tereza Ribeiro; Freitas, Ana Teresa; Agnez-Lima, Lucymara F.

2017-01-01

Background Bacterial and Archaeal communities have a complex, symbiotic role in crude oil bioremediation. Their biosurfactants and degradation enzymes have been in the spotlight, mainly due to the awareness of ecosystem pollution caused by crude oil accidents and their use. Initially, the scientific community studied the role of individual microbial species by characterizing and optimizing their biosurfactant and oil degradation genes, studying their individual distribution. However, with the...

Biofilm lifestyle enhances diesel bioremediation and biosurfactant production in the Antarctic polyhydroxyalkanoate producer Pseudomonas extremaustralis.

Science.gov (United States)

Tribelli, Paula M; Di Martino, Carla; López, Nancy I; Raiger Iustman, Laura J

2012-09-01

Diesel is a widely distributed pollutant. Bioremediation of this kind of compounds requires the use of microorganisms able to survive and adapt to contaminated environments. Pseudomonas extremaustralis is an Antarctic bacterium with a remarkable survival capability associated to polyhydroxyalkanoates (PHAs) production. This strain was used to investigate the effect of cell growth conditions--in biofilm versus shaken flask cultures--as well as the inocula characteristics associated with PHAs accumulation, on diesel degradation. Biofilms showed increased cell growth, biosurfactant production and diesel degradation compared with that obtained in shaken flask cultures. PHA accumulation decreased biofilm cell attachment and enhanced biosurfactant production. Degradation of long-chain and branched alkanes was observed in biofilms, while in shaken flasks only medium-chain length alkanes were degraded. This work shows that the PHA accumulating bacterium P. extremaustralis can be a good candidate to be used as hydrocarbon bioremediation agent, especially in extreme environments.

Instrumentation and Control in Anaerobic Digestion

DEFF Research Database (Denmark)

Anaerobic digestion is a multistep process, and is most applied to solids destruction and wastewater treatment for energy production. Despite wide application, and long-term industrial proof of application, some industries are still reluctant to apply this technology. One of the classical reasons...... benchmark. There has therefore been, overall, a quantum advance in application and sophistication of instrumentation and control in anaerobic digestion, and it is an effective option for improved process loading rate and conversion efficiency....... are still a limitation, but this is being partly addressed by the increased complexity of digestion processes. Methods for control benchmarking have also been improved, as there is now an industry standard model (the IWA ADM1), and this is being applied in an improved whole wastewater treatment plant...

Application of saponin biosurfactant and its recovery in the MEUF process for removal of methyl violet from wastewater.

Science.gov (United States)

Samal, Kulbhushan; Das, Chandan; Mohanty, Kaustubha

2017-12-01

The potential of saponin, a biosurfactant, in the micellar enhanced ultrafiltration (MEUF) process was tested systematically for removal of methyl violet from wastewater. For this, the aqueous extract of reetha (Sapindus mukorossi) pericarp which contains saponin was used as the biosurfactant. First, the micellar solubilization of methyl violet in saponin micelles was investigated in terms of molar solubilization power (SP) of saponin. It was observed that the adsorption of methyl violet on the agglomerates of saponin micelles was mainly responsible for the enhanced solubilization. The Gibbs free energy of solubilization (calculated as -29.63 kJ mol -1 ) suggested that process was feasible and spontaneous. The MEUF experiments were performed in batch as well as continuous mode using saponin biosurfactant, and the effect of operating parameters on permeate flux and solute retention were evaluated. The removal of methyl violet in MEUF process was >99% achieved with 10 kDa polyethersulfone (PES) membrane for feed dye concentration of 250 mg L -1 at studied conditions. Finally, the saponin in permeate was recovered using n-heptane and n-butanol by solvent extraction process. The solvent n-butanol showed better extraction efficiency as compared to n-heptane for saponin extraction. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaluation of biological properties and fate in the environment of a new class of biosurfactants.

Science.gov (United States)

Liwarska-Bizukojc, Ewa; Olejnik, Dorota; Delbeke, Elisabeth I P; Van Geem, Kevin M; Stevens, Christian V

2018-06-01

Selected sophorolipid quaternary ammonium salts (SQAS), being a new class of modified biosurfactants, were studied in this work for the first time with regard to their biodegradability and fate in the environment. It was made to find whether environment-friendly bioproducts like biosurfactants are still safe to the environment after their chemical modification. The susceptibility of these SQAS for biodegradation was estimated together with the evaluation of their influence on activated sludge microorganisms. Additionally, the mechanisms of removal of the SQAS from wastewater and from the aquatic environment, were analysed. The evaluated SQAS were potentially biodegradable, although none of them could be classified as readily biodegradable. The biodegradation degrees after 28 days ranged from 4 to 42%, dependent on the SQAS tested, i.e. below the required OECD 301D Closed Bottle Test level of 60%. Simultaneously, the analysis of the mass spectra revealed the presence of the breakdown products of each SQAS studied. Biodegradation was preceded by sorption of the SQAS on sludge particles, which occurred to be a main mechanism of the removal of these newly synthesized biosurfactants from wastewater. The mean degree of sorption calculated on the basis of SQAS determination was from 75 to 96%, dependent on the studied SQAS. The presence of SQAS in wastewater did not deteriorate the operation of the activated sludge system, although the products of the SQAS biodegradation remained in the liquid phase and might contribute to the increase of COD of the effluent to be introduced to the environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Bioremediation of petroleum contaminated soil to combat toxicity on Withania somnifera through seed priming with biosurfactant producing plant growth promoting rhizobacteria.

Science.gov (United States)

Das, Amar Jyoti; Kumar, Rajesh

2016-06-01

Soil contaminated by Petroleum oil cannot be utilized for agricultural purposes due to hydrocarbon toxicity. Oil contaminated soil induces toxicity affecting germination, growth and productivity. Several technologies have been proposed for bioremediation of oil contaminated sites, but remediation through biosurfactant producing plant growth promontory rhizobacteria (PGPR) is considered to be most promising methods. In the present study the efficacy of seed priming on growth and pigment of Withania somnifera under petroleum toxicity is explored. Seeds of W. somnifera were primed with biosurfactant producing Pseudomonas sp. AJ15 with plant growth promoting traits having potentiality to utilized petroleum as carbon source. Results indicates that plant arose from priming seeds under various petroleum concentration expressed high values for all the parameters studied namely germination, shoot length, root length, fresh and dry weight and pigments (chlorophyll and carotenoid) as compared to non primed seed. Hence, the present study signifies that petroleum degrarding biosurfactant producing PGPR could be further used for management and detoxification of petroleum contaminated soils for growing economically important crops. Copyright © 2016. Published by Elsevier Ltd.

Antibiotic and biosurfactant properties of cyclic lipopeptides produced by fluorescent Pseudomonas spp. from the sugar beet rhizosphere

DEFF Research Database (Denmark)

Nielsen, T.H.; Sørensen, D.; Tobiasen, C.

2002-01-01

Cyclic lipopeptides (CLPs) with antibiotic and biosurfactant properties are produced by a number of soil bacteria, including fluorescent Pseudomonas spp. To provide new and efficient strains for the biological control of root-pathogenic fungi in agricultural crops, we isolated approximately 600...... fluorescent Pseudomonas spp. from two different agricultural soils by using three different growth media. CLP production was observed in a large proportion of the strains (approximately 60%) inhabiting the sandy soil, compared to a low proportion (approximately 6%) in the loamy soil. Chemical structure...... in the peptide moiety. Production of specific CLPs could be affiliated with Pseudomonas fluorescens strain groups belonging to biotype I, V, or VI. In vitro analysis using both purified CLPs and whole-cell P. fluorescens preparations demonstrated that all CLPs exhibited strong biosurfactant properties...

Improving methane production from anaerobic digestion of Pennisetum Hybrid by alkaline pretreatment.

Science.gov (United States)

Kang, Xihui; Sun, Yongming; Li, Lianhua; Kong, Xiaoying; Yuan, Zhenhong

2018-05-01

Alkaline pretreatment with NaOH was used to improve methane yield from Pennisetum Hybrid. The pretreatments were carried out with different NaOH solutions (2-8% w/w) at three temperatures (35, 55 and 121 °C) for different periods of time (24, 24 and 1 h). All treated and untreated Pennisetum Hybrid were digested under mesophilic conditions (37 °C) to biogas, significant effects of the pretreatments on the yield of methane were observed. Results showed the modified Gompertz equation was reliable (determination coefficients (R 2 ) greater than 0.96) to describe the kinetic behavior of anaerobic digestion of Pennisetum Hybrid. The best result, obtained by the treatment at 35 °C 2% NaOH for 24 h, resulted in the methane yield of 301.7 mL/g VS, corresponding to 21.0% improvement in the methane yield. Compositional, SEM, XRD and FTIR analysis confirmed that lignin removal, structural modification and cellulose crystalline variation were responsible for the improvement. Copyright © 2018 Elsevier Ltd. All rights reserved.

Characterization of a Soybean Oil-based Biosurfactant and Evaluation of its Ability to Form Microbubbles

Science.gov (United States)

This paper characterizes the physio-chemical properties of the soybean oil (SBO)-based polymeric surfactant, Palozengs R-004 (hereafter referred to as R-004). The surface activity of R-004 is comparable to the reported activities of biosurfactants produced by microorganisms and higher than some of ...

Wet and Dry Anaerobic Digestion of Biowaste and of Co-substrates

OpenAIRE

Li, Chaoran

2015-01-01

Treatment of municipal solid waste by anaerobic digestion can solve the environmental problems caused by this organic solid waste and also supply biogas as renewable energy for a sustainable development. In this study the improvement of wet anaerobic digestion by addition of co-substrates and the effect of moisture on dry anaerobic digestion were investigated.

Influence of toluene and salinity on biosurfactant production by Bacillus sp.: scale up from flasks to a bench-scale bioreactor

Directory of Open Access Journals (Sweden)

Ellen Cristina Souza

Full Text Available ABSTRACT To select the best biosurfactant producer, Pseudomonas putida, Bacillus megatherium, Bacillus licheniformis and Bacillus subtilis were cultured in flasks on media with different salinity [low salinity (LS, Bushnell-Haas (BH and artificial sea water (SW media] supplemented or not with toluene as a model pollutant. Toluene inhibited the growth of all microorganisms and stimulated the biosurfactant production. B. subtilis exhibited the best performance, being able to lower the surface tension (ST in the LS medium to 65.5 mN/min in the absence of toluene, and to 46.5 mN/min in the BH medium in the presence of toluene, corresponding to ST reductions of 13.0 and 27.5 mN/m, respectively. Scaling up the process to a bench-scale fermentor, the best results were obtained in the LS medium, where B. subtilis was able to reduce the toluene concentration from 26.0 to 4.3 g/L within 12 h and ST by 17.2 mN/m within 18 h. The results of this study point out that B. subtilis is an interesting biosurfactant producer, which could be used in the bioremediation of toluene-contaminated water.

EFFECT OF MUSIC ON ANAEROBIC EXERCISE PERFORMANCE

Directory of Open Access Journals (Sweden)

Tülin Atan

2013-01-01

Full Text Available For years, mostly the effects of music on cardiorespiratory exercise performance have been studied, but a few studies have examined the effect of music on anaerobic exercise. The purpose of this study was to assess the effect of listening to music and its rhythm on anaerobic exercise: on power output, heart rate and the concentration of blood lactate. 28 male subjects were required to visit the laboratory on 6 occasions, each separated by 48 hours. Firstly, each subject performed the Running-based Anaerobic Sprint Test (RAST under 3 conditions on separate days: while listening to “slow rhythm music”, “fast rhythm music” or “no music”. 48 hours after the subjects completed RAST under 3 conditions, Wingate Anaerobic Power (WAN tests were performed under 3 music conditions. The order of the 3 conditions (slow music, fast music and no music was selected randomly to prevent an order effect. Results showed no significant differences between 3 conditions in anaerobic power assessments, heart rate or blood lactate (p>0.05. On the basis of these results it can be said that music cannot improve anaerobic performance. The type of music had no impact on power outputs during RAST and WAN exercise. As a conclusion, listening to music and its rhythm cannot enhance anaerobic performance and cannot change the physiological response to supramaximal exercise.

Enhancement of anaerobic sludge digestion by high-pressure homogenization.

Science.gov (United States)

Zhang, Sheng; Zhang, Panyue; Zhang, Guangming; Fan, Jie; Zhang, Yuxuan

2012-08-01

To improve anaerobic sludge digestion efficiency, the effects of high-pressure homogenization (HPH) conditions on the anaerobic sludge digestion were investigated. The VS and TCOD were significantly removed with the anaerobic digestion, and the VS removal and TCOD removal increased with increasing the homogenization pressure and homogenization cycle number; correspondingly, the accumulative biogas production also increased with increasing the homogenization pressure and homogenization cycle number. The optimal homogenization pressure was 50 MPa for one homogenization cycle and 40 MPa for two homogenization cycles. The SCOD of the sludge supernatant significantly increased with increasing the homogenization pressure and homogenization cycle number due to the sludge disintegration. The relationship between the biogas production and the sludge disintegration showed that the accumulative biogas and methane production were mainly enhanced by the sludge disintegration, which accelerated the anaerobic digestion process and improved the methane content in the biogas. Copyright © 2012 Elsevier Ltd. All rights reserved.

Serial completely stirred tank reactors for improving biogas production and substance degradation during anaerobic digestion of corn stover.

Science.gov (United States)

Li, YuQian; Liu, ChunMei; Wachemo, Akiber Chufo; Yuan, HaiRong; Zou, DeXun; Liu, YanPing; Li, XiuJin

2017-07-01

Several completely stirred tank reactors (CSTR) connected in series for anaerobic digestion of corn stover were investigated in laboratory scale. Serial anaerobic digestion systems operated at a total HRT of 40days, and distribution of HRT are 10+30days (HRT10+30d), 20+20days (HRT20+20d), and 30+10days (HRT30+10d) were compared to a conventional one-step CSTR at the same HRT of 40d. The results showed that in HRT10+30d serial system, the process became very unstable at organic load of 50gTS·L -1 . The HRT20+20d and HRT30+10d serial systems improved methane production by 8.3-14.6% compared to the one-step system in all loads of 50, 70, 90gTS·L -1 . The conversion rates of total solid, cellulose, and hemicellulose were increased in serial anaerobic digestion systems compared to single system. The serial systems showed more stable process performance in high organic load. HRT30+10d system showed the best biogas production and conversions among all systems. Copyright © 2017. Published by Elsevier Ltd.

Improving the cyanide toxicity tolerance of anaerobic reactor: Microbial interactions and toxin reduction

International Nuclear Information System (INIS)

Gupta, Pragya; Ahammad, S.Z.; Sreekrishnan, T.R.

2016-01-01

Highlights: • Anaerobic batch study of 110 days. • Acclimatization for cyanide biodegradation. • Understanding inhibitory effects of cyanide on methane generation and VFA production. • Identification of microorganisms tolerant to cyanide. • Community analysis using DGGE and qPCR analyses. - Abstract: Anaerobic biological treatment of high organics containing wastewater is amongst the preferred treatment options but poor tolerance to toxins makes its use prohibitive. In this study, efforts have been made to understand the key parameters for developing anaerobic reactor, resilient to cyanide toxicity. A laboratory scale anaerobic batch reactor was set up to treat cyanide containing wastewater. The reactor was inoculated with anaerobic sludge obtained from a wastewater treatment plant and fresh cow dung in the ratio of 3:1. The focus was on acclimatization and development of cyanide-degrading biomass and to understand the toxic effects of cyanide on the dynamic equilibrium between various microbial groups. The sludge exposed to cyanide was found to have higher bacterial diversity than the control. It was observed that certain hydrogenotrophic methanogens and bacterial groups were able to grow and produce methane in the presence of cyanide. Also, it was found that hydrogen utilizing methanogens were more cyanide tolerant than acetate utilizing methanogens. So, effluents from various industries like electroplating, coke oven plant, petroleum refining, explosive manufacturing, and pesticides industries which are having high concentrations of cyanide can be treated by favoring the growth of the tolerant microbes in the reactors. It will provide much better treatment efficiency by overcoming the inhibitory effects of cyanide to certain extent.

Improving the cyanide toxicity tolerance of anaerobic reactor: Microbial interactions and toxin reduction

Energy Technology Data Exchange (ETDEWEB)

Gupta, Pragya; Ahammad, S.Z.; Sreekrishnan, T.R., E-mail: sree@iitd.ac.in

2016-09-05

Highlights: • Anaerobic batch study of 110 days. • Acclimatization for cyanide biodegradation. • Understanding inhibitory effects of cyanide on methane generation and VFA production. • Identification of microorganisms tolerant to cyanide. • Community analysis using DGGE and qPCR analyses. - Abstract: Anaerobic biological treatment of high organics containing wastewater is amongst the preferred treatment options but poor tolerance to toxins makes its use prohibitive. In this study, efforts have been made to understand the key parameters for developing anaerobic reactor, resilient to cyanide toxicity. A laboratory scale anaerobic batch reactor was set up to treat cyanide containing wastewater. The reactor was inoculated with anaerobic sludge obtained from a wastewater treatment plant and fresh cow dung in the ratio of 3:1. The focus was on acclimatization and development of cyanide-degrading biomass and to understand the toxic effects of cyanide on the dynamic equilibrium between various microbial groups. The sludge exposed to cyanide was found to have higher bacterial diversity than the control. It was observed that certain hydrogenotrophic methanogens and bacterial groups were able to grow and produce methane in the presence of cyanide. Also, it was found that hydrogen utilizing methanogens were more cyanide tolerant than acetate utilizing methanogens. So, effluents from various industries like electroplating, coke oven plant, petroleum refining, explosive manufacturing, and pesticides industries which are having high concentrations of cyanide can be treated by favoring the growth of the tolerant microbes in the reactors. It will provide much better treatment efficiency by overcoming the inhibitory effects of cyanide to certain extent.

Isolation and Identification of Crude Oil Degrading and Biosurfactant Producing Bacteria from the Oil-Contaminated Soils of Gachsaran

Directory of Open Access Journals (Sweden)

Seyyedeh Zahra Hashemi

2016-03-01

Full Text Available Background and Objectives: Petroleum hydrocarbons are harmful to the environment, human health, and all other living creatures. Oil and its byproducts in contact with water block sunshine to phytoplanktons and thus break the food chain and damage the marine food source. This study aims to isolate the crude oil degrading and biosurfactant producing bacteria from the oil contaminated soils of Gachsaran, Iran. Materials and Methods: Isolation was performed in peptone-water medium with yeast extract. Oil displacement area, emulsification index and bacterial phylogeny using 16S rRNA analysis were studied. Results and Conclusion: Three isolates were able to degrade the crude oil. In the first day, there were two phases in the medium; after a few days, these three bacteria degraded the crude oil until there was only one phase left in the medium. One strain was selected as a superior strain by homogenizing until the medium became clear and transparent. This method confirmed that the strain produces biosurfactant. According to the morphological and biochemical tests, the strain isolated from the oil contaminated soils is a member of Bacillus subtilis, so to study the bacterial phylogeny and taxonomy of the strain, an analysis of 16S rRNA was carried out, and the phylogenic tree confirmed them. The results verified that oil contaminated soils are good source for isolation of the biosurfactant producing bacteria.

Anaerobic Digestion: Process

DEFF Research Database (Denmark)

Angelidaki, Irini; Batstone, Damien J.

2011-01-01

Organic waste may degrade anaerobically in nature as well as in engineered systems. The latter is called anaerobic digestion or biogasification. Anaerobic digestion produces two main outputs: An energy-rich gas called biogas and an effluent. The effluent, which may be a solid as well as liquid...... with very little dry matter may also be called a digest. The digest should not be termed compost unless it specifically has been composted in an aerated step. This chapter describes the basic processes of anaerobic digestion. Chapter 9.5 describes the anaerobic treatment technologies, and Chapter 9...

The challenges of anaerobic digestion and the role of biochar in optimizing anaerobic digestion.

Science.gov (United States)

Fagbohungbe, Michael O; Herbert, Ben M J; Hurst, Lois; Ibeto, Cynthia N; Li, Hong; Usmani, Shams Q; Semple, Kirk T

2017-03-01

Biochar, like most other adsorbents, is a carbonaceous material, which is formed from the combustion of plant materials, in low-zero oxygen conditions and results in a material, which has the capacity to sorb chemicals onto its surfaces. Currently, research is being carried out to investigate the relevance of biochar in improving the soil ecosystem, digestate quality and most recently the anaerobic digestion process. Anaerobic digestion (AD) of organic substrates provides both a sustainable source of energy and a digestate with the potential to enhance plant growth and soil health. In order to ensure that these benefits are realised, the anaerobic digestion system must be optimized for process stability and high nutrient retention capacity in the digestate produced. Substrate-induced inhibition is a major issue, which can disrupt the stable functioning of the AD system reducing microbial breakdown of the organic waste and formation of methane, which in turn reduces energy output. Likewise, the spreading of digestate on land can often result in nutrient loss, surface runoff and leaching. This review will examine substrate inhibition and their impact on anaerobic digestion, nutrient leaching and their environmental implications, the properties and functionality of biochar material in counteracting these challenges. Copyright © 2016 Elsevier Ltd. All rights reserved.

PENGOLAHAN LIMBAH CAIR INDUSTRI FARMASI FORMULASI DENGAN METODE ANAEROB-AEROB DAN ANAEROB-KOAGULASI

OpenAIRE

Farida Crisnaningtyas; Hanny Vistanty

2016-01-01

Studi ini membahas mengenai pengolahan limbah cair industri farmasi dalam skala laboratorium dengan menggunakan konsep anaerob-kimia-fisika dan anaerob-aerob. Proses anaerob dilakukan dengan menggunakan reaktor Upflow Anaerobic Sludge Bed reactor (UASBr) pada kisaran OLR (Organic Loading Rate) 0,5 – 2 kg COD/m3hari, yang didahului dengan proses aklimatisasi menggunakan substrat gula. Proses anaerob mampu memberikan efisiensi penurunan COD hingga 74%. Keluaran dari proses anaerob diolah lebih ...

Biosorption of Congo Red from aqueous solution by Bacillus weihenstephanensis RI12; effect of SPB1 biosurfactant addition on biodecolorization potency.

Science.gov (United States)

Mnif, Inès; Fendri, Raouia; Ghribi, Dhouha

2015-01-01

Bacillus weihenstephanensis RI12, isolated from hydrocarbon contaminated soil, was assessed for Congo Red bio-treatment potency. Results suggested the potential of this bacterium for use in effective treatment of Congo Red contaminated wastewaters under shaking conditions at acidic and neutral pH value. The strain could tolerate higher doses of dyes as it could decolorize up to 1,000 mg/l of Congo Red. When used as microbial surfactant to enhance Congo Red biodecolorization, Bacillus subtilis SPB1-derived lipopeptide accelerated the decolorization rate and maximized the decolorization efficiency at an optimal concentration of biosurfactant of about 0.075%. Studies ensured that Congo Red removal by this strain could be due to an adsorption phenomena. Germination potencies of tomato seeds using the treated dyes under different conditions showed the efficient biotreatment of the azo dye Congo Red especially with the addition of SPB1 biosurfactant. To conclude, the addition of SPB1 bioemulsifier reduced energy costs by reducing the effective decolorization period; the biosurfactant stimulated bacterial decolorization method may provide a highly efficient, inexpensive and time-saving procedure in the treatment of textile effluents.

Anaerobes in pleuropulmonary infections

Directory of Open Access Journals (Sweden)

De A

2002-01-01

Full Text Available A total of 76 anaerobes and 122 aerobes were isolated from 100 patients with pleuropulmonary infections, e.g. empyema (64, pleural effusion (19 and lung abscess (13. In 14% of the patients, only anaerobes were recovered, while a mixture of aerobes and anaerobes was encountered in 58%. From all cases of lung abscess, anaerobic bacteria were isolated, alone (04 or along with aerobic bacteria (13. From empyema and pleural effusion cases, 65.6% and 68.4% anaerobes were recovered respectively. Amongst anaerobes, gram negative anaerobic bacilli predominated (Prevotella melaninogenicus 16, Fusobacterium spp. 10, Bacteroides spp. 9, followed by gram positive anaerobic cocci (Peptostreptococcus spp. 31. Coliform bacteria (45 and Pseudomonas aeruginosa (42 were the predominant aerobic isolates.

High Intensity Interval Training Leads to Greater Improvements in Acute Heart Rate Recovery and Anaerobic Power as High Volume Low Intensity Training

Science.gov (United States)

Stöggl, Thomas L.; Björklund, Glenn

2017-01-01

The purpose of the current study was to explore if training regimes utilizing diverse training intensity distributions result in different responses on neuromuscular status, anaerobic capacity/power and acute heart rate recovery (HRR) in well-trained endurance athletes. Methods: Thirty-six male (n = 33) and female (n = 3) runners, cyclists, triathletes and cross-country skiers [peak oxygen uptake: (VO2peak): 61.9 ± 8.0 mL·kg−1·min−1] were randomly assigned to one of three groups (blocked high intensity interval training HIIT; polarized training POL; high volume low intensity oriented control group CG/HVLIT applying no HIIT). A maximal anaerobic running/cycling test (MART/MACT) was performed prior to and following a 9-week training period. Results: Only the HIIT group achieved improvements in peak power/velocity (+6.4%, P 0.05). Acute HRR was improved in HIIT (11.2%, P = 0.002) and POL (7.9%, P = 0.023) with no change in the HVLIT oriented control group. Conclusion: Only a training regime that includes a significant amount of HIIT improves the neuromuscular status, anaerobic power and the acute HRR in well-trained endurance athletes. A training regime that followed more a low and moderate intensity oriented model (CG/HVLIT) had no effect on any performance or HRR outcomes. PMID:28824457

Biosurfactant Mediated Biosynthesis of Selected Metallic Nanoparticles

Directory of Open Access Journals (Sweden)

Grażyna A. Płaza

2014-08-01

Full Text Available Developing a reliable experimental protocol for the synthesis of nanomaterials is one of the challenging topics in current nanotechnology particularly in the context of the recent drive to promote green technologies in their synthesis. The increasing need to develop clean, nontoxic and environmentally safe production processes for nanoparticles to reduce environmental impact, minimize waste and increase energy efficiency has become essential in this field. Consequently, recent studies on the use of microorganisms in the synthesis of selected nanoparticles are gaining increased interest as they represent an exciting area of research with considerable development potential. Microorganisms are known to be capable of synthesizing inorganic molecules that are deposited either intra- or extracellularly. This review presents a brief overview of current research on the use of biosurfactants in the biosynthesis of selected metallic nanoparticles and their potential importance.

Biosurfactant Mediated Biosynthesis of Selected Metallic Nanoparticles

Science.gov (United States)

Płaza, Grażyna A.; Chojniak, Joanna; Banat, Ibrahim M.

2014-01-01

Developing a reliable experimental protocol for the synthesis of nanomaterials is one of the challenging topics in current nanotechnology particularly in the context of the recent drive to promote green technologies in their synthesis. The increasing need to develop clean, nontoxic and environmentally safe production processes for nanoparticles to reduce environmental impact, minimize waste and increase energy efficiency has become essential in this field. Consequently, recent studies on the use of microorganisms in the synthesis of selected nanoparticles are gaining increased interest as they represent an exciting area of research with considerable development potential. Microorganisms are known to be capable of synthesizing inorganic molecules that are deposited either intra- or extracellularly. This review presents a brief overview of current research on the use of biosurfactants in the biosynthesis of selected metallic nanoparticles and their potential importance. PMID:25110864

Role of a waste-derived polymeric biosurfactant in the sol-gel synthesis of nanocrystalline titanium dioxide

DEFF Research Database (Denmark)

Boffa, Vittorio; Perrone, Daniele G.; Magnacca, Giuliana

2014-01-01

An inexpensive polymeric biosurfactant isolated from urban bio-wastes is shown to be a useful chemical aid in the synthesis of nanostructured materials with tunable pore size and surface hydrophilicity. Photocatalytic active TiO2 powders were prepared by sol–gel reaction in the presence of variable...

Anaerobic treatment of municipal wastewater in a UASB-Digester system

NARCIS (Netherlands)

Zhang, Lei

2016-01-01

A novel treatment chain for low strength domestic sewage includes low temperature anaerobic treatment as the main process. It can improve the energy efficiency of sewage treatment compared with conventional aerobic sewage treatment. A combination of an Upflow Anaerobic Sludge Blanket reactor and

Biosurfactant production from Pseudomonas taiwanensis L1011 and its application in accelerating the chemical and biological decolorization of azo dyes.

Science.gov (United States)

Liu, Cong; You, Yanting; Zhao, Ruofei; Sun, Di; Zhang, Peng; Jiang, Jihong; Zhu, Aihua; Liu, Weijie

2017-11-01

Dye dispersion and the interaction efficiency between azoreductases and dye molecules are rate-limiting steps for the decolorization of azo dyes. In this study, a biosurfactant-producing strain, Pseudomonas taiwanensis L1011, was isolated from crude oil. To increase the yield of the biosurfactant BS-L1011 from P. taiwanensis L1011, culture conditions were optimized including temperature, initial pH, carbon source, nitrogen source and C/N ratio. A maximum yield of 1.12g/L of BS-L1011 was obtained using D-mannitol as carbon source and yeast extract/urea as compound nitrogen source with C/N ratio of 10/4, pH 7.0 and 28°C. BS-L1011 exhibited a low critical micelle concentration (CMC) of 10.5mg/L and was able to reduce the surface tension of water to 25.8±0.1 mN/m. BS-L1011 was stable over a wide range of temperatures, pH values and salt concentrations. The biosurfactant is reported for the first time to accelerate chemical decolorization of Congo red by sodium hypochlorite, and biological decolorization of Amaranth by Bacillus circulans BWL1061, thus showing a potential in the treatment of dyeing wastewater. Copyright © 2017 Elsevier Inc. All rights reserved.

Effects of Lactobacillus reuteri-derived biosurfactant on the gene expression profile of essential adhesion genes (gtfB, gtfC and ftf of Streptococcus mutans

Directory of Open Access Journals (Sweden)

Rasoul Salehi

2014-01-01

Full Text Available Background: Streptococci are the main causative agents in plaque formation and mutans streptococci are the principle etiological agent of dental plaque and caries. The process of biofilm formation is a step-wise process, starting with adhesion of planktonic cells to the surfaces. It is now a well known fact that expression of glucosyltransferases (gtfs and fructosyltransferase (ftf genes play a critical role in the initial adhesion of Streptococcus mutans to the tooth surface, which results in the formation of dental plaques and consequently caries and other periodontal diseases. Materials and Methods: In the present study, we have determined the effect of biosurfactants purified from Lactobacillus reuteri (DSM20016 culture on gene expression profile of gftB/C and fft of S. mutans (ATCC35668 using quantitative real-time polymerase chain reaction. Results: The application of biosurfactant caused considerable down-regulation of the expression of all three genes under study. The reduction in gene expression was statistically very significant (P > 0.0001 for all three genes. Conclusions: Inhibition of these genes by the extracted L. reuteri biosurfactant shows the emergence of a powerful alternative to the presently practicing alternatives. In view of the importance of these gene products for S. mutans attachment to the tooth surface, which is the initial important step in biofilm production and dental caries, we believe that the biosurfactant prepared in this study could be considered as a step ahead in dental caries prevention.

The utility of anaerobic blood culture in detecting facultative anaerobic bacteremia in children.

Science.gov (United States)

Shoji, Kensuke; Komuro, Hisako; Watanabe, Yasushi; Miyairi, Isao

2013-08-01

Routine anaerobic blood culture is not recommended in children because obligate anaerobic bacteremia is rare in the pediatric population. However, a number of facultative anaerobic bacteria can cause community and hospital acquired infections in children and the utility of anaerobic blood culture for detection of these organisms is still unclear. We conducted a retrospective analysis of all blood culture samples (n = 24,356) at a children's hospital in Japan from October 2009 to June 2012. Among the samples that had paired aerobic and anaerobic blood cultures, 717 samples were considered clinically significant with 418 (58%) organisms detected from both aerobic and anaerobic cultures, 167 (23%) detected only from aerobic culture and 132 (18%) detected only from anaerobic culture. While most facultative anaerobes were detectable by aerobic culture, over 25% of Enterobacteriaceae and 15% of Staphylococcus sp. were detected from anaerobic cultures bottles only, suggesting its potential role in selected settings. Copyright © 2013 Elsevier Inc. All rights reserved.

Potential applications of biosurfactant rhamnolipids in agriculture and biomedicine.

Science.gov (United States)

Chen, Jianwei; Wu, Qihao; Hua, Yi; Chen, Jun; Zhang, Huawei; Wang, Hong

2017-12-01

Rhamnolipids have recently emerged as promising bioactive molecules due to their novel structures, diverse and versatile biological functions, lower toxicity, higher biodegradability, as well as production from renewable resources. The advantages of rhamnolipids make them attractive targets for research in a wide variety of applications. Especially rhamnolipids are likely to possess potential applications of the future in areas such as biomedicine, therapeutics, and agriculture. The purpose of this mini review is to provide a comprehensive prospective of biosurfactant rhamnolipids as potential antimicrobials, immune modulators, and virulence factors, and anticancer agents in the field of biomedicine and agriculture that may meet the ever-increasing future pharmacological treatment and food safety needs in human health.