WorldWideScience

Sample records for ieee trans ultrason

  1. Trans-skull ultrasonic Doppler system aided by fuzzy logic

    Science.gov (United States)

    Hata, Yutaka; Nakamura, Masato; Yagi, Naomi; Ishikawa, Tomomoto

    2012-06-01

    This paper describes a trans-skull ultrasonic Doppler system for measuring the blood flow direction in brain under skull. In this system, we use an ultrasonic array probe with the center frequency of 1.0 MHz. The system determines the fuzzy degree of blood flow by Doppler Effect, thereby it locates blood vessel. This Doppler Effect is examined by the center of gravity shift of the frequency magnitudes. In in-vitro experiment, a cow bone was employed as the skull, and three silicon tubes were done as blood vessels, and bubble in water as blood. We received the ultrasonic waves through a protein, the skull and silicon tubes in order. In the system, fuzzy degrees are determined with respect to the Doppler shift, amplitude of the waves and attenuation of the tissues. The fuzzy degrees of bone and blood direction are calculated by them. The experimental results showed that the system successfully visualized the skull and flow direction, compared with the location and flow direction of the phantom. Thus, it detected the flow direction by Doppler Effect under skull, and automatically extracted the region of skull and blood vessel.

  2. Effect of ultrasonic waves on the stability of all-trans lutein and its degradation kinetics.

    Science.gov (United States)

    Song, Jiang-Feng; Li, Da-Jing; Pang, Hui-Li; Liu, Chun-Quan

    2015-11-01

    Ultrasound treatment has been widely applied in the extraction of biologically active compounds including carotenoids. However, there are few reports on their effects on the stability of these compounds. In the present study, the stability of all-trans lutein, one of the carotenoids, was investigated under the action of ultrasound. Results showed that ultrasound induced the isomerization of all-trans lutein to its isomers, namely to 13-cis lutein, 13'-cis lutein, 9-cis lutein and 9'-cis lutein as analyzed by HPLC coupled with DAD and LC-MS; and the percentage of the isomerization increased with increasing both ultrasonic frequency and power. The stability of all-trans lutein in dichloromethane was worst among multiple kinds of solvents. Interestingly, the retention rate of all-trans lutein improved as the temperature increased, which runs counter to the Arrhenius law. Under ultrasound irradiation, the degradation mechanism might be different with various temperatures, the degradation of all-trans lutein followed first-order kinetics at 20°C, while second-order kinetics was followed at 30-50°C. As the ultrasonic reaction time prolonged, lutein epoxidation nearly occurred. Those results presented here emphasized that UAE techniques should be carefully used in the extraction of all-trans lutein. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Design and installation of high-temperature ultrasonic measuring system and grinder for nuclear fuel containing trans-uranium elements

    International Nuclear Information System (INIS)

    Serizawa, Hiroyuki; Kikuchi, Hironobu; Iwai, Takashi; Arai, Yasuo; Kurosawa, Makoto; Mimura, Hideaki; Abe, Jiro

    2005-07-01

    A high-temperature ultrasonic measuring system had been designed and installed in a glovebox (711-DGB) to study a mechanical property of nuclear fuel containing trans-uranium (TRU) elements. A figuration apparatus for the cylinder-type sample preparation had also been modified and installed in an established glovebox (142-D). The system consists of an ultrasonic probe, a heating furnace, cooling water-circulating system, a cooling air compressor, vacuum system, gas supplying system and control system. An A/D converter board and an pulsar/receiver board for the measurement of wave velocity were installed in a personal computer. The apparatus was modified to install into the glovebox. Some safety functions were supplied to the control system. The shape and size of the sample was revised to minimize the amount of TRU elements for the use of the measurement. The maximum sample temperature is 1500degC. The performance of the installed apparatuses and the glovebox were confirmed through a series of tests. (author)

  4. Ultrasonic brain therapy: First trans-skull in vivo experiments on sheep using adaptive focusing

    Science.gov (United States)

    Pernot, Mathieu; Aubry, Jean-Francois; Tanter, Michael; Fink, Mathias; Boch, Anne-Laure; Kujas, Michèle

    2004-05-01

    A high-power prototype dedicated to trans-skull therapy has been tested in vivo on 20 sheep. The array is made of 200 high-power transducers working at 1-MHz central and is able to reach 260 bars at focus in water. An echographic array connected to a Philips HDI 1000 system has been inserted in the therapeutic array in order to perform real-time monitoring of the treatment. A complete craniotomy has been performed on half of the treated animal models in order to get a reference model. On the other animals, a minimally invasive surgery has been performed thanks to a time-reversal experiment: a hydrophone was inserted at the target inside the brain thanks to a 1-mm2 craniotomy. A time-reversal experiment was then conducted through the skull bone with the therapeutic array to treat the targeted point. For all the animals a specified region around the target was treated thanks to electronic beam steering. Animals were finally divided into three groups and sacrificed, respectively, 0, 1, and 2 weeks after treatment. Finally, histological examination confirmed tissue damage. These in vivo experiments highlight the strong potential of high-power time-reversal technology.

  5. Diastereoselective synthesis of trans-2,3-dihydrofuro[3,2-c]coumarins by MgO nanoparticles under ultrasonic irradiation

    Directory of Open Access Journals (Sweden)

    Javad Safaei-Ghomi

    2017-12-01

    Full Text Available MgO nanoparticles have been used as an efficient catalyst for the diastereoselective preparation of trans-2-benzoyl-3-(aryl-2H-furo[3,2-c]chromen-4(3H-ones by the multi-component reaction of 2,4′-dibromoacetophenone, pyridine, benzaldehydes and 4-hydroxycoumarin under ultrasonic irradiation. This interesting result revealed that the pyridiniumylide assisted tandem three-component coupling reaction is highly diastereoselective. Atom economy, wide range of products, high catalytic activity, excellent yields in short reaction times, diastereoselective synthesis and environmental benignity are some of the important features of this protocol. Keywords: Furo[3,2-c]coumarins, Ultrasonic irradiation, MgO nanoparticles, Diastereoselective, One-pot syntheses

  6. Diastereoselective synthesis of trans-2,3-dihydrofuro[3,2-c]coumarins by MgO nanoparticles under ultrasonic irradiation

    OpenAIRE

    Javad Safaei-Ghomi; Pouria Babaei; Hossein Shahbazi-Alavi; Safura Zahedi

    2017-01-01

    MgO nanoparticles have been used as an efficient catalyst for the diastereoselective preparation of trans-2-benzoyl-3-(aryl)-2H-furo[3,2-c]chromen-4(3H)-ones by the multi-component reaction of 2,4â²-dibromoacetophenone, pyridine, benzaldehydes and 4-hydroxycoumarin under ultrasonic irradiation. This interesting result revealed that the pyridiniumylide assisted tandem three-component coupling reaction is highly diastereoselective. Atom economy, wide range of products, high catalytic activity, ...

  7. IEEE Smart Grid Series of Standards IEEE 2030 (Interoperability) and IEEE 1547 (Interconnection) Status: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Basso, T.; DeBlasio, R.

    2012-04-01

    The IEEE American National Standards smart grid publications and standards development projects IEEE 2030, which addresses smart grid interoperability, and IEEE 1547TM, which addresses distributed resources interconnection with the grid, have made substantial progress since 2009. The IEEE 2030TM and 1547 standards series focus on systems-level aspects and cover many of the technical integration issues involved in a mature smart grid. The status and highlights of these two IEEE series of standards, which are sponsored by IEEE Standards Coordinating Committee 21 (SCC21), are provided in this paper.

  8. IEEE Prize for Lucio Rossi

    CERN Multimedia

    IEEE Council on Superconductivity

    2007-01-01

    Lucio Rossi receives his prize from John Spargo, Chairman of the IEEE Council on Superconductivity (left), and Martin Nisenoff, Chairman of the Council on Superconductivity's Awards Committee (right).

  9. Access to IEEE Electronic Library

    CERN Multimedia

    2007-01-01

    From 2007, the CERN Library now offers readers online access to the complete IEEE Electronic Library (Institute of Electrical and Electronics Engineers). This new licence gives unlimited online access to all IEEE and IET (previously IEE) journals and proceedings as well as all current IEEE standards and selected archived ones. Some of the titles offer volumes back to 1913. This service currently represents more than 1,400,000 full-text articles! This leading engineering information resource replaces the previous service, a sub-product of the IEEE database called 'IEEE Enterprise', which offered online access to the complete collection of IEEE journals and proceedings, but with limited features. The service had become so popular that the CERN Working Group for Acquisitions recommended that the Library subscribe to the complete IEEE Electronic Library for 2007. Usage statistics for recent months showed there was a demand for the service from a large community of CERN users and we were aware that many users h...

  10. Ultrasonic Testing

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hyeong Jun; Kuk, Jeong Han

    2002-02-15

    This book introduces ultrasonic testing, which tells of outline of ultrasonic testing, principle of ultrasonic testing, prosperities of ultrasonic waves, radiographic test and ultrasonic test, basic theory on ultrasonic testing, mode conversion, transmission and diffraction, ultrasonic flaw detection and probe, standard test piece and reference test piece, like KS(JIS) ASME and ASTM, classification and properties of ultrasonic testing, straight beam method, angle beam method, ASME SEC.V.Art.5 ASTMA 388 and KS B 0817 Korean industrial standard.

  11. IEEE Conference Publications in Libraries.

    Science.gov (United States)

    Johnson, Karl E.

    1984-01-01

    Conclusions of surveys (63 libraries, OCLC database, University of Rhode Island users) assessing handling of Institute of Electrical and Electronics Engineers (IEEE) conference publications indicate that most libraries fully catalog these publications using LC cataloging, and library patrons frequently require series access to publications. Eight…

  12. Researching the roots of IEEE Region 8

    NARCIS (Netherlands)

    Bastiaans, M.J.

    2013-01-01

    This paper describes the preliminary steps towards the foundation and the early history of IRE Region 9 / IEEE Region 8. The information has been gathered mainly from the archives of the IEEE Benelux Section.

  13. 2012 IEEE Vehicular Networking Conference (VNC)

    NARCIS (Netherlands)

    Altintas, Onur; Chen, Wai; Heijenk, Geert; Oh, Hyun Seo; Chung, Jong-Moon; Dressler, Falko; Kargl, Frank; Pau, Giovanni; Schoch, Elmar

    2012-01-01

    On behalf of the Organizing Committee, we would like to welcome you to the fourth edition of the IEEE Vehicular Networking Conference in Seoul, Korea. IEEE VNC is a unique conference sponsored by both IEEE Communications Society and Intelligent Transportation Systems Society. It brings together

  14. IEEE Prize for Lucio Rossi

    CERN Multimedia

    2007-01-01

    Lucio Rossi receives his prize from John Spargo, Chairman of the IEEE Council on Superconductivity (left), and Martin Nisenoff, Chairman of the Council on Superconductivity’s Awards Committee (right). (Photo: IEEE Council on Superconductivity)With the magnets installed in the tunnel and work on the interconnections almost completed, Lucio Rossi has reaped the rewards of fifteen years of work. And yet, when the physicist from Milan arrived to take charge of the group responsible for the superconducting magnets in 2001, success seemed far from assured. Endowed with surprising levels of energy, Lucio Rossi, together with his team, ensured that production of these highly complex magnets got underway. Today, that achievement earns them the recognition not only of CERN but also of the international superconducting community. It is for this achievement that Lucio Rossi was awarded the prize by the IEEE’s (Institute of Electrical an...

  15. Trans* Leadership.

    Science.gov (United States)

    Jourian, T J; Simmons, Symone L

    2017-06-01

    Focusing on emerging literature on trans* and gender-nonconforming students and their leadership, this chapter outlines the ways trans* students are engaged in leadership in educational institutions and outside of them and discusses implications for staff and faculty regarding how to support and engage these students and their leadership. © 2017 Wiley Periodicals, Inc., A Wiley Company.

  16. Ultrasonic signature

    International Nuclear Information System (INIS)

    Borloo, E.; Crutzen, S.

    1974-12-01

    The unique and tamperproof identification technique developed at Ispra is based on ultrasonic Non-Destructive-Techniques. Reading fingerprints with ultrasonic requires high reproducibility of standard apparatus and transducers. The present report gives an exhaustive description of the ultrasonic technique developed for identification purposes. Different applications of the method are described

  17. Ultrasonic testing

    Energy Technology Data Exchange (ETDEWEB)

    Song, Sung Jin [Sungkwunkwan Univ., Seoul (Korea, Republic of); Jeong, Hyun Jo [Wonkwang Univ., Iksan (Korea, Republic of)

    2004-02-15

    For the proper performance of ultrasonic testing of steel welded joints, and anisotropic material it is necessary to have sound understanding on the underlying physics. To provide such an understanding, it is beneficial to have simulation tools for ultrasonic testing. In order to address such a need, we develop effective approaches to simulate angle beam ultrasonic testing with a personal computer. The simulation is performed using ultrasonic measurement models based on the computationally efficient multi-Gaussian beams. This reach will describe the developed ultrasonic testing models together with the experimental verification of their accuracy.

  18. Ultrasonic physics

    CERN Document Server

    Richardson, E G

    1962-01-01

    Ultrasonic Physics, Second Edition, provides an introduction to the fundamental principles of ultrasonic physics. The book opens with a discussion of the sources of ultrasound. This is followed by separate chapters on the properties and detection of ultrasonic radiation; measurement of propagation constants, i.e., the velocity and absorption, of ultrasound; ultrasound propagation in gases, liquids, and solids; and ultrasound propagation in aerosols, suspensions, and emulsions. The final chapter covers miscellaneous physical and physico-chemical actions, including dispersion and coagulation of

  19. The IEEE Milestone event at CERN

    CERN Multimedia

    2005-01-01

    On the initiative of its French and Swiss Sections, the IEEE has honoured CERN with an 'IEEE Milestone in the history of electricity and electronics' for the invention of the multi-wire proportional chamber in 1968. The IEEE established the Electrical Engineering Milestones programe in 1983 to honour significant achievements in the history of electrical and electronics engineering. To be designated, an achievement must be at least 25 years old, must have involved a unique solution to an engineering problem, and must have had at least regional impact. Currently there are more than  50 IEEE Milestones around the world. http://www.ieee.org/organizations/history_center/cern.html The installation and unveiling of this IEEE Milestone will provide the opportunity to emphasize the close relationship between science, technology, industry and well-being in society.  A ceremony, organised with the support of a group of IEEE members working at CERN, will be held at the CERN Globe of Science and Inn...

  20. CERN receives prestigious Milestone recognition from IEEE

    CERN Multimedia

    2005-01-01

    At a ceremony at CERN, Mr W. Cleon Anderson, President of the Institute of Electrical and Electronics Engineers (IEEE) formally a Milestone plaque in recognition of the invention of electronic particle detectors at CERN

  1. Ultrasonic inspection

    International Nuclear Information System (INIS)

    Satittada, Gannaga

    1984-01-01

    Ultrasonic inspection is one of the most widely used methods for nondestructive inspection. The beam of high-frequency sound wave, ultrasonic wave, is introduced into the material. It travels through the material with some attendant loss of energy and can be reflected at interfaces. The reflected beam is detected and analyzed. Ultrasonic inspection is used to detect flaws in metal parts as well as in welded, brazed and bonded joints during research work and developing production and service. It is also used to detect and locate porosity, pipe, and flakes. In addition, it can be used for the measurement of metal thickness. Ultrasonic inspection is therefore used for quality control and material inspection in all major industries

  2. Ultrasonic mammography

    International Nuclear Information System (INIS)

    Hueneke, B.

    1982-01-01

    608 women are examined by means of ultrasonic mammography during the period of 1 year. 432 patients were examined with the compound method with the U.I. Octoson, a water tank scanner, and 176 patients with the real time method with a directly connected linear-array-scanner. The following results were obtained at the end of the examination period: In the ultrasonic and also in the X-ray mammogram tumour diameters can be determined with an error rate of +- 30%. In the diagnosing of carcinomas, a significant dependence of the exactness on the sice of the tumour is found for the combination of the five methods tested (clinical examination, X-ray mammography, ultrasonic mammography, thermography, cytology). Classifying the individual methods with regard to their exactness, X-ray mammography ranks in front of ultrasonic mammography. Mastopathic changes in the breast can be screened by means of ultrasonic mammography. The structure of the changes can be determined more exactly than with an X-ray picture which is due to the possibility of differentiating solid and cystic structures. In diagnosing fibro-adenomas and establishing diagnoses on young women with dense gland bodies, ultrasonic mammography is superior to radiology both in the ability of screening a finding of a fibro-adenoma (US=88%, X-ray=75%) and in the possibility of classifying it as ''more benign than malignant''. (orig./MG) [de

  3. IEEE International Symposium on Biomedical Imaging.

    Science.gov (United States)

    2017-01-01

    The IEEE International Symposium on Biomedical Imaging (ISBI) is a scientific conference dedicated to mathematical, algorithmic, and computational aspects of biological and biomedical imaging, across all scales of observation. It fosters knowledge transfer among different imaging communities and contributes to an integrative approach to biomedical imaging. ISBI is a joint initiative from the IEEE Signal Processing Society (SPS) and the IEEE Engineering in Medicine and Biology Society (EMBS). The 2018 meeting will include tutorials, and a scientific program composed of plenary talks, invited special sessions, challenges, as well as oral and poster presentations of peer-reviewed papers. High-quality papers are requested containing original contributions to the topics of interest including image formation and reconstruction, computational and statistical image processing and analysis, dynamic imaging, visualization, image quality assessment, and physical, biological, and statistical modeling. Accepted 4-page regular papers will be published in the symposium proceedings published by IEEE and included in IEEE Xplore. To encourage attendance by a broader audience of imaging scientists and offer additional presentation opportunities, ISBI 2018 will continue to have a second track featuring posters selected from 1-page abstract submissions without subsequent archival publication.

  4. Fabrication and characterization of a 20 MHz ultrasonic transducer using soft mold process: Poster presented at Joint IEEE International Symposium on the Applications of Ferroelectrics, European Conference on Applications of Polar Dielectrics & Workshop on Piezoresponse Force Microscopy, ISAF/ECAPD/PFM 2016, Darmstadt, 21.-25.8.2016

    OpenAIRE

    Günther, Paul; Gebhardt, Sylvia; Neubert, Holger; Herzog, Thomas; Heuer, Henning; Walter, Susan

    2016-01-01

    High frequency ultrasonic transducers based on fine scale 1-3 piezocomposites enable high resolution in medical or material imaging. As increasing frequency requires decreasing pillar size and kerf width, the conventional dice-and-fill technique is limited by blade thickness and becomes more sophisticated with smaller dimensions. In contrast, the soft mold technique allows for fine-scale piezoceramic arrays with free design of pillar geometry and spatial distribution. Basis of the procedure a...

  5. CERN receives prestigious Milestone recognition from IEEE

    CERN Multimedia

    2005-01-01

    The Nobel prize winner Georges Charpak and W. Cleon Anderson, IEEE President, unveil the Milestone bronze plaques. At a ceremony on 26 September at the Globe of Science and Innovation, Mr W. Cleon Anderson, President of the Institute of Electrical and Electronics Engineers (IEEE) formally dedicated Milestone plaques recognising the invention of electronic particle detectors at CERN. The plaque were unveiled by Mr Anderson and Georges Charpak, the Nobel-prize winning inventor of wire chamber technology at CERN in 1968. The IEEE is the world's largest professional association dedicated to the advancement of technology with 365,000 individual members in over 150 countries. Established in 1983, there are currently over 60 Milestones around the world. They honour momentous achievements in the history of electrical and electronics engineering, such as the landing of the first transatlantic cable, code breaking at Bletchley Park during World War II, and the development of the Japanese Bullet train, the Tokaido Shin...

  6. The scalable coherent interface, IEEE P1596

    International Nuclear Information System (INIS)

    Gustavson, D.B.

    1990-01-01

    IEEE P1596, the scalable coherent interface (formerly known as SuperBus) is based on experience gained while developing Fastbus (ANSI/IEEE 960--1986, IEC 935), Futurebus (IEEE P896.x) and other modern 32-bit buses. SCI goals include a minimum bandwidth of 1 GByte/sec per processor in multiprocessor systems with thousands of processors; efficient support of a coherent distributed-cache image of distributed shared memory; support for repeaters which interface to existing or future buses; and support for inexpensive small rings as well as for general switched interconnections like Banyan, Omega, or crossbar networks. This paper presents a summary of current directions, reports the status of the work in progress, and suggests some applications in data acquisition and physics

  7. Ultrasonic neuromodulation

    Science.gov (United States)

    Naor, Omer; Krupa, Steve; Shoham, Shy

    2016-06-01

    Ultrasonic waves can be non-invasively steered and focused into mm-scale regions across the human body and brain, and their application in generating controlled artificial modulation of neuronal activity could therefore potentially have profound implications for neural science and engineering. Ultrasonic neuro-modulation phenomena were experimentally observed and studied for nearly a century, with recent discoveries on direct neural excitation and suppression sparking a new wave of investigations in models ranging from rodents to humans. In this paper we review the physics, engineering and scientific aspects of ultrasonic fields, their control in both space and time, and their effect on neuronal activity, including a survey of both the field’s foundational history and of recent findings. We describe key constraints encountered in this field, as well as key engineering systems developed to surmount them. In closing, the state of the art is discussed, with an emphasis on emerging research and clinical directions.

  8. Ultrasonic flowmeters

    International Nuclear Information System (INIS)

    Wittekind, W.D.

    1979-01-01

    A prototype ultrasonic flowmeter was assembled and tested. The theoretical basis of this prototype ultrasonic flowmeter is reviewed; the equipment requirements for a portable unit are discussed; the individual electronic modules contained in the prototype are described; the operating procedures and configuration are explained; and the data from preliminary calibrations are presented. The calibration data confirm that the prototype operates according to theoretical predictions and can indeed provide nonintrusive flow measurements to predicted accuracies for pipes larger than two inches, under single phase stable flow conditions

  9. Editorial for IEEE Transactions on Power Electronics

    DEFF Research Database (Denmark)

    Blaabjerg, Frede

    2007-01-01

    Our IEEE transactions on power electronics has had some very positive progress these past years under the leadership of Dr. Daan van Wyk. Papers have been processed efficiently both in review time and publication time. This success has spread throughout the whole power electronics community which...

  10. The IEEE 802.11a standards

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. The IEEE 802.11a standards. Provides higher data rate and system capacities and uses OFDM in Physical Layer to mitigate the multi path effects;. Supports multiple 20Mhz channel. Each channel being an OFDM Modulated;; 52 Carriers. 48 data carrier; 4 Carry pilot ...

  11. Ultrasonic hydrometer

    Science.gov (United States)

    Swoboda, Carl A.

    1984-01-01

    The disclosed ultrasonic hydrometer determines the specific gravity (density) of the electrolyte of a wet battery, such as a lead-acid battery. The hydrometer utilizes a transducer that when excited emits an ultrasonic impulse that traverses through the electrolyte back and forth between spaced sonic surfaces. The transducer detects the returning impulse, and means measures the time "t" between the initial and returning impulses. Considering the distance "d" between the spaced sonic surfaces and the measured time "t", the sonic velocity "V" is calculated with the equation "V=2d/t". The hydrometer also utilizes a thermocouple to measure the electrolyte temperature. A hydrometer database correlates three variable parameters including sonic velocity in and temperature and specific gravity of the electrolyte, for temperature values between 0.degree. and 40.degree. C. and for specific gravity values between 1.05 and 1.30. Upon knowing two parameters (the calculated sonic velocity and the measured temperature), the third parameter (specific gravity) can be uniquely found in the database. The hydrometer utilizes a microprocessor for data storage and manipulation. The disclosed modified battery has a hollow spacer nub on the battery side wall, the sonic surfaces being on the inside of the nub and the electrolyte filling between the surfaces to the exclusion of intervening structure. An accessible pad exposed on the nub wall opposite one sonic surface allows the reliable placement thereagainst of the transducer.

  12. Trans-Planckian wimpzillas

    CERN Document Server

    Kolb, E W; Tkachev, I I

    2007-01-01

    Two previously proposed conjectures--gravitational trans-Planckian particle creation in the expanding universe, and the existence of ultra-heavy stable particles with masses up to the Planck scale (wimpzillas)--are combined in a proposal for trans-Planckian particle creation of wimpzillas. It is shown that the trans-Planckian particle creation parameter should be rather small to avoid overproduction of such particles. This ensures that wimpzillas are mainly created at the end of primordial inflation. Conditions under which trans-Planckian wimpzillas can constitute the present dark matter are determined.

  13. 7th IEEE International Conference Intelligent Systems

    CERN Document Server

    Atanassov, KT; Doukovska, L; Hadjiski, M; Jotsov, V; Kacprzyk, J; Kasabov, N; Sotirov, S; Szmidt, E; Zadrożny, S; Filev, D; Jabłkowski, J; Kacprzyk, J; Krawczak, M; Popchev, I; Rutkowski, L; Sgurev, V; Sotirova, E; Szynkarczyk, P

    2015-01-01

    This two volume set of books constitutes the proceedings of the 2014  7th IEEE International Conference Intelligent Systems (IS), or IEEE IS’2014 for short, held on September 24‐26, 2014 in Warsaw, Poland. Moreover, it contains some selected papers from the collocated IWIFSGN'2014-Thirteenth International Workshop on Intuitionistic Fuzzy Sets and Generalized Nets.The conference was organized by the Systems Research Institute, Polish Academy of Sciences, Department IV of Engineering Sciences, Polish Academy of Sciences, and Industrial Institute of Automation and Measurements - PIAP.The papers included in the two proceedings volumes have been subject to a thorough review process by three highly qualified peer reviewers.Comments and suggestions from them have considerable helped improve the quality of the papers but also the division of the volumes into parts, and assignment of the papers to the best suited parts.  

  14. IEEE 802.11 ECG monitoring system.

    Science.gov (United States)

    Tejero-Calado, Juan; Lopez-Casado, Carmen; Bernal-Martin, Antonio; Lopez-Gomez, Miguel; Romero-Romero, Marco; Quesada, Guillermo; Lorca, Julio; Rivas, Ramon

    2005-01-01

    New wireless technologies make possible the implementation of high level integration wireless devices which allow the replacement of traditional large wired monitoring devices. This kind of devices favours at-home hospitalization, reducing the affluence to sanitary assistance centers to make routine controls. This fact causes a really favourable social impact, especially for elder people, rural-zone inhabitant, chronic patients and handicapped people. Furthermore, it offers new functionalities to physicians and will reduce the sanitary cost. Among these functionalities, biomedical signals can be sent to other devices (screen, PDA, PC...) or processing centers, without restricting the patients' mobility. The aim of this project is the development and implementation of a reduced size multi-channel electrocardiograph based on IEEE 802.11, which allows wireless monitoring of patients, and the insertion of the information into the TCP/IP Hospital network.

  15. IEEE International Workshop on Machine Learning for Signal Processing: Preface

    DEFF Research Database (Denmark)

    Tao, Jianhua

    The 21st IEEE International Workshop on Machine Learning for Signal Processing will be held in Beijing, China, on September 18–21, 2011. The workshop series is the major annual technical event of the IEEE Signal Processing Society's Technical Committee on Machine Learning for Signal Processing...

  16. Facts about trans fats

    Science.gov (United States)

    Trans fat is a type of dietary fat . Of all the fats, trans fat is the worst for your health. Too much ... from solid margarine to soft margarine. Ask what type of fats foods are cooked in when you eat out ...

  17. Trans as Contested Intelligibility

    DEFF Research Database (Denmark)

    Raun, Tobias

    2014-01-01

    Denne artikel rejser en række epistemologiske og metodologiske spørgsmål vedrørende læsningen af trans som identitetskategori. Disse spørgsmål er stærkt underbelyste i en skandinavisk akademisk kontekst, om end der el- lers i stigende grad produceres analyser af trans identitetsnarrativer. Artikl...

  18. Proceedings of IEEE Machine Learning for Signal Processing Workshop XV

    DEFF Research Database (Denmark)

    Larsen, Jan

    These proceedings contains refereed papers presented at the Fifteenth IEEE Workshop on Machine Learning for Signal Processing (MLSP’2005), held in Mystic, Connecticut, USA, September 28-30, 2005. This is a continuation of the IEEE Workshops on Neural Networks for Signal Processing (NNSP) organized...... by the NNSP Technical Committee of the IEEE Signal Processing Society. The name of the Technical Committee, hence of the Workshop, was changed to Machine Learning for Signal Processing in September 2003 to better reflect the areas represented by the Technical Committee. The conference is organized...... by the Machine Learning for Signal Processing Technical Committee with sponsorship of the IEEE Signal Processing Society. Following the practice started two years ago, the bound volume of the proceedings is going to be published by IEEE following the Workshop, and we are pleased to offer to conference attendees...

  19. Performance comparison of IEEE 802.11g and IEEE 802.11n in the presence of interference from 802.15.4 networks

    OpenAIRE

    Masood, Syed Haani

    2013-01-01

    In this paper we compare the packet error rate (PER) and maximum throughput of IEEE 802.11n and IEEE 802.11g under interference from IEEE 802.15.4 by using MATLAB to simulate the IEEE PHY for 802.11n and 802.11g networks.

  20. A coexistence model of IEEE 802.15.4 and IEEE 802.1 lbIg

    NARCIS (Netherlands)

    Yuan, Wei; Wang, Xiangyu; Linnartz, J.P.M.G.

    2007-01-01

    IEEE 802.15.4 was developed to meet the needs for low-rate wireless communication. However, due to its low power, IEEE 802.15.4 is potentially vulnerable to interference by other wireless technologies having much higher power and working in the same industrial, scientific, and medical (ISM) band

  1. Active Channel Reservation for Coexistence Mechanism (ACROS) for IEEE 802.15.4 and IEEE 802.11

    Science.gov (United States)

    Shin, Soo Young; Woo, Dong Hyuk; Lee, Jong Wook; Park, Hong Seong; Kwon, Wook Hyun

    In this paper, a coexistence mechanism between IEEE 802.15.4 and IEEE 802.11b, Active Channel Reservation for cOexiStence (ACROS), is proposed. The key idea underlining ACROS is to reserve the channel for IEEE 802.15.4 transmission, where IEEE 802.11 transmissions are forbidden. The request-to-send (RTS)/clear-to send (CTS) mechanism within IEEE 802.11 is used to reserve a channel. The proposed ACROS mechanism is implemented into a PC based prototype. The embedded version of ACROS is also developed to mitigate the timing drift problem in the PC-based ACROS. The efficiency of ACROS is shown using the throughput and packet error rate achieved in actual experiments.

  2. Cis By Trans

    OpenAIRE

    Rodovalho,Amara Moira

    2017-01-01

    Cis, trans: above all, metaphors. Cisjordan, region skirting the Jordan River. Cisplatin, Uruguay’s ancient name, region occupying one of the banks of the Prata River. Trans- Amazonian, that which crosses the Amazon; transatlantic, that which crosses the Atlantic. Cisalpine, transalpine. The geometric isomerism of Organic Chemistry, where “cis” are atoms that, when molecules are divided in half, remain on the same side, and “trans” those remaining on opposite sides. Ev...

  3. Guest editors' introduction : Highlights from IEEE Pacific Visualization

    NARCIS (Netherlands)

    Wijk, van J.J.; North, S.; Shen, H.-W.

    2010-01-01

    This article looks briefly at four articles based on papers from the 2010 IEEE Pacific Visualization Symposium. These articles, which strongly focus on visual design and applications, cover a range of applications in scientific visualization, information visualization, and graph visualization,

  4. IEEE Conference Record - Abstracts. 1997 IEEE International Conference on Plasma Science, 19 - 22 May 1997 San Diego, California

    National Research Council Canada - National Science Library

    Hyman, Julius

    1997-01-01

    This 360 page softbound publication includes the following major sections. An invitation to ICOPS'97, Catamaran Resort Hotel Floor Pinas, Officers of the IEEE Nuclear and Plasma Sciences Society, Conference Information...

  5. Ultrasonic horn design for ultrasonic machining technologies

    Directory of Open Access Journals (Sweden)

    Naď M.

    2010-07-01

    Full Text Available Many of industrial applications and production technologies are based on the application of ultrasound. In many cases, the phenomenon of ultrasound is also applied in technological processes of the machining of materials. The main element of equipments that use the effects of ultrasound for machining technology is the ultrasonic horn – so called sonotrode. The performance of ultrasonic equipment, respectively ultrasonic machining technologies depends on properly designed of sonotrode shape. The dynamical properties of different geometrical shapes of ultrasonic horns are presented in this paper. Dependence of fundamental modal properties (natural frequencies, mode shapes of various sonotrode shapes for various geometrical parameters is analyzed. Modal analyses of the models are determined by the numerical simulation using finite element method (FEM design procedures. The mutual comparisons of the comparable parameters of the various sonotrode shapes are presented.

  6. Delay Analysis of GTS Bridging between IEEE 802.15.4 and IEEE 802.11 Networks for Healthcare Applications

    Science.gov (United States)

    Mišić, Jelena; (Sherman) Shen, Xuemin

    2009-01-01

    We consider interconnection of IEEE 802.15.4 beacon-enabled network cluster with IEEE 802.11b network. This scenario is important in healthcare applications where IEEE 802.15.4 nodes comprise patient's body area network (BAN) and are involved in sensing some health-related data. BAN nodes have very short communication range in order to avoid harming patient's health and save energy. Sensed data needs to be transmitted to an access point in the ward room using wireless technology with higher transmission range and rate such as IEEE 802.11b. We model the interconnected network where IEEE 802.15.4-based BAN operates in guaranteed time slot (GTS) mode, and IEEE 802.11b part of the bridge conveys GTS superframe to the 802.11b access point. We then analyze the network delays. Performance analysis is performed using EKG traffic from continuous telemetry, and we discuss the delays of communication due the increasing number of patients. PMID:19107184

  7. Delay Analysis of GTS Bridging between IEEE 802.15.4 and IEEE 802.11 Networks for Healthcare Applications.

    Science.gov (United States)

    Misić, Jelena; Sherman Shen, Xuemin

    2009-01-01

    We consider interconnection of IEEE 802.15.4 beacon-enabled network cluster with IEEE 802.11b network. This scenario is important in healthcare applications where IEEE 802.15.4 nodes comprise patient's body area network (BAN) and are involved in sensing some health-related data. BAN nodes have very short communication range in order to avoid harming patient's health and save energy. Sensed data needs to be transmitted to an access point in the ward room using wireless technology with higher transmission range and rate such as IEEE 802.11b. We model the interconnected network where IEEE 802.15.4-based BAN operates in guaranteed time slot (GTS) mode, and IEEE 802.11b part of the bridge conveys GTS superframe to the 802.11b access point. We then analyze the network delays. Performance analysis is performed using EKG traffic from continuous telemetry, and we discuss the delays of communication due the increasing number of patients.

  8. Simulasi Kinerja Jaringan Nirkabel IEEE-802.11a dan IEEE-802.11g Menggunakan NS-2

    Directory of Open Access Journals (Sweden)

    Helm Fitriawan

    2014-03-01

    Full Text Available Wireless network uses transmission media based on radio waves. This type of networks is mainly useddue to its efficiency and mobility in data exchanging. This paper reports the modeling and simulation of wirelessnetworks based on Cisco Aironet 1130ag access point devices with IEEE 802.11a and IEEE 802.11g standards. Themodeling and simulation are performed using network simulator version 2 (NS-2 that is installed on operationsystem Linux Ubuntu v.10.10. The NS-2 is commonly used and works well in numerous types of network simulation. From simulation, we obtain quality of service parameters by employing several simulation scenarios in terms ofnumber of nodes, distances, and packet data sizes. It can be concluded from simulation results that the IEEE 802.11gnetworks transfer data with better quality than those of IEEE 802.11a networks.  Furthermore, the IEEE 802.11gnetworks provide a higher throughput, with smaller amount of delay and packet loss percentage compared to thoseof IEEE 802.11a networks.

  9. Electromagnetic ultrasonic guided waves

    CERN Document Server

    Huang, Songling; Li, Weibin; Wang, Qing

    2016-01-01

    This book introduces the fundamental theory of electromagnetic ultrasonic guided waves, together with its applications. It includes the dispersion characteristics and matching theory of guided waves; the mechanism of production and theoretical model of electromagnetic ultrasonic guided waves; the effect mechanism between guided waves and defects; the simulation method for the entire process of electromagnetic ultrasonic guided wave propagation; electromagnetic ultrasonic thickness measurement; pipeline axial guided wave defect detection; and electromagnetic ultrasonic guided wave detection of gas pipeline cracks. This theory and findings on applications draw on the author’s intensive research over the past eight years. The book can be used for nondestructive testing technology and as an engineering reference work. The specific implementation of the electromagnetic ultrasonic guided wave system presented here will also be of value for other nondestructive test developers.

  10. Ultrasonic testing device

    International Nuclear Information System (INIS)

    Lawrie, W.E.

    1978-01-01

    The ultrasonic transmitter made of polarized ferroelectric ceramic material (lead zirconate titanate) is arranged in a strip carrier which allows it to be introduced between the fuel elements of a fuel subassembly in a water cooled nuclear reactor. The ultrasonic transmitter is insulated relative to the carrier. The echo of the ra dal ultrasonic pulse is recorded which changes as faulty water filled fuel elements are detected. (RW) [de

  11. IEEE Std 101-1987: IEEE guide for the statistical analysis of thermal life test data

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This revision of IEEE Std 101-1972 describes statistical analyses for data from thermally accelerated aging tests. It explains the basis and use of statistical calculations for an engineer or scientist. Accelerated test procedures usually call for a number of specimens to be aged at each of several temperatures appreciably above normal operating temperatures. High temperatures are chosen to produce specimen failures (according to specified failure criteria) in typically one week to one year. The test objective is to determine the dependence of median life on temperature from the data, and to estimate, by extrapolation, the median life to be expected at service temperature. This guide presents methods for analyzing such data and for comparing test data on different materials

  12. Fiber optics backbone for IEEE 802.3 networks

    Science.gov (United States)

    Shani, Ron

    1990-01-01

    In the last few years the IEEE 802.3 committee has developed fiber optics inter-repeater link standard called FOIRL. This standard defines the "Fiber Optics Media Access Unit" (FOMAU) which is used to connect two IEEE 802.3 repeaters that are up to 1Km apart. The IEEE 802.3 lOBaseF task force is currently standardizing a full F/O system in two directions: passive and active. The active approach is a compromise between the FOIRL (Asynchronous) approach and the Synchronous approach. As a result of this activity the IEEE 802.3 standard will define three different F/O interfaces and several devices that will not inter-operate. Such a standard will lower the credibility among the IEEE 802.3 user community, as customers will be confused amidst the many chapters and devices with no clear choice. This paper describes a method that can reduce the number of standards to two (passive and active), while proposing a solution for all the requirements of 802.3 F/O LAN. (The question of passive vs active approach will be discussed in this paper).

  13. Trans-Spatial Utopias

    Science.gov (United States)

    Kramsch, Claire

    2018-01-01

    The "trans-" perspectives offered in this special issue are heady stuff. Post-structuralism (philosophy) meets the digital age (electronics), meets globalization (economics), and meets translingual practice (linguistics) to create a perfectly utopian or placeless space for future exploration. I want to first add my voice to the…

  14. Low Trans Hydrogenation

    Science.gov (United States)

    Although hydrogenation has been the technology of choice for fat formulation for many years recent concerns over the health and nutrition of trans fatty acids have had a profound effect on the edible oil industry. Since Jan. 1, 2006, TFA has been required on nutrition labels along with saturated an...

  15. Ultrasonic flow meter

    NARCIS (Netherlands)

    Lötters, Joost Conrad; Snijders, G.J.; Volker, A.W.F.

    2014-01-01

    The invention relates to an ultrasonic flow meter comprising a flow tube for the fluid whose flow rate is to be determined. The flow meter comprises a transmitting element for emitting ultrasonic waves, which is provided on the outer jacket of the flow tube. A receiving element, which is provided on

  16. Implicit Block ACK Scheme for IEEE 802.11 WLANs

    Science.gov (United States)

    Sthapit, Pranesh; Pyun, Jae-Young

    2016-01-01

    The throughput of IEEE 802.11 standard is significantly bounded by the associated Medium Access Control (MAC) overhead. Because of the overhead, an upper limit exists for throughput, which is bounded, including situations where data rates are extremely high. Therefore, an overhead reduction is necessary to achieve higher throughput. The IEEE 802.11e amendment introduced the block ACK mechanism, to reduce the number of control messages in MAC. Although the block ACK scheme greatly reduces overhead, further improvements are possible. In this letter, we propose an implicit block ACK method that further reduces the overhead associated with IEEE 802.11e’s block ACK scheme. The mathematical analysis results are presented for both the original protocol and the proposed scheme. A performance improvement of greater than 10% was achieved with the proposed implementation.

  17. IEEE guide for the analysis of human reliability

    International Nuclear Information System (INIS)

    Dougherty, E.M. Jr.

    1987-01-01

    The Institute of Electrical and Electronics Engineers (IEEE) working group 7.4 of the Human Factors and Control Facilities Subcommittee of the Nuclear Power Engineering Committee (NPEC) has released its fifth draft of a Guide for General Principles of Human Action Reliability Analysis for Nuclear Power Generating Stations, for approval of NPEC. A guide is the least mandating in the IEEE hierarchy of standards. The purpose is to enhance the performance of an human reliability analysis (HRA) as a part of a probabilistic risk assessment (PRA), to assure reproducible results, and to standardize documentation. The guide does not recommend or even discuss specific techniques, which are too rapidly evolving today. Considerable maturation in the analysis of human reliability in a PRA context has taken place in recent years. The IEEE guide on this subject is an initial step toward bringing HRA out of the research and development arena into the toolbox of standard engineering practices

  18. Ultrasonic decontamination robot

    International Nuclear Information System (INIS)

    Patenaude, R.S.

    1984-01-01

    An ultrasonic decontamination robot removes radioactive contamination from the internal surface of the inlet and outlet headers, divider plate, tube sheet, and lower portions of tubes of a nuclear power plant steam generator. A programmable microprocessor controller guides the movement of a robotic arm mounted in the header manway. An ultrasonic transducer having a solvent delivery subsystem through which ultrasonic action is achieved is moved by the arm over the surfaces. A solvent recovery suction tube is positioned within the header to remove solvent therefrom while avoiding interference with the main robotic arm. The solvent composition, temperature, pressure, viscosity, and purity are controlled to optimize the ultrasonic scrubbing action. The ultrasonic transducer is controlled at a power density, frequency, and on-off mode cycle such as to optimize scrubbing action within the range of transducer-to-surface distance and solvent layer thickness selected for the particular conditions encountered. Both solvent and transducer control actions are optimized by the programmable microprocessor. (author)

  19. IEEE prize awarded to CERN PhD student

    CERN Multimedia

    2006-01-01

    Rafael Ballabriga Suñe is the recipient of the 2006 Institute of Electrical and Electronics Engineers, Inc. (IEEE) Nuclear and Plasma Sciences Society (NPSS)'s Student Paper Award. Ballabriga's winning paper reported on a prototype chip, which belongs to a new generation of single photon counting hybrid pixel detector readout chips - Medipix3. The award was presented by the deputy programme chair Vince Cianciolo (left) at the IEEE Nuclear Science Symposium held in San Diego on 29 October to 4 November.

  20. IEEE C37.98-1987: IEEE standard seismic testing of relays

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This standard specifies the procedures to be used in the seismic testing of relays used in power system facilities. The standard is concerned with the determination of the seismic fragility level of relays and also gives recommendations for proof testing. The purpose of this standard is to establish procedures for determining the seismic capabilities of protective and auxiliary relays. These procedures employ what has been called fragility testing in IEEE Std 344-1987. To define the conditions for fragility testing of relays, parameters in three separate areas must be specified. In general, they are (1) the electrical settings and inputs to the relay, and other information to define its conditions during the test; (2) the change in state, deviation in operating characteristics or tolerances, or other change of performance of the relay that constitutes failure; (3) the seismic vibration environment to be imposed during the test. Since it is not possible to define the conditions for every conceivable application for all relays, those parameters, which in practice encompass the majority of applications, have been specified in this standard. When the application of the relay is other than as specified under any of (1), (2), and (3), or if it is not practical to apply existing results of fragility tests to that new application, then proof testing must be performed for that new case

  1. IEEE C37.98-1978: IEEE standard seismic testing of relays

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This standard specifies the procedures to be used in the seismic testing of relays used in power system facilities. The standard is concerned with the determination of the seismic fragility level of relays and also gives recommendations for proof testing. The purpose of this standard is to establish procedures for determining the seismic capabilities of protective and auxiliary relays. These procedures employ what has been called fragility testing in ANSI/IEEE Std 344-1975, Recommended Practices for Seismic Qualification of Class 1E Equipment for Nuclear Power Generating Stations. In order to define the conditions for fragility testing of relays, parameters in three separate areas must be specified. In general they are: (1) the electrical settings and inputs to the relay, and other information to define its conditions during the test; (2) the change in state, deviation in operating characteristics or tolerances, or other change of performance of the relay which constitutes failure; (3) the seismic vibration environment to be imposed during the test. Since it is not possible to define the conditions for every conceivable application for all relays, those parameters, which in practice encompass the majority of applications, have been specified in this standard. When the application of the relay is other than as specified under any of (1), (2), and (3), or if it is not practical to apply existing results of fragility tests to that new case

  2. A trans world journey

    DEFF Research Database (Denmark)

    Stender, Steen; Dyerberg, Jørn; Bysted, Anette

    2006-01-01

    to a maximum of 2% of fat content from 2004. We assessed the potential exposure of consumers to IP-TFA by analysing popular foods in Denmark, and in 25 other countries. Fifty-five servings of French fries and chicken nuggets, 87 packages of microwave popcorn, and 393 samples of biscuits....../cakes/wafers with "partially hydrogenated vegetable fat" listed high on the food label were bought between November 2004, and February 2006. The content of IP-TFA was analysed by standardized methodology. We defined a "high trans menu" as a large size serving of French fries and nuggets, 100 g of microwave popcorn, and 100 g......A high intake of industrially produced trans fatty acids (IP-TFA) is associated with increased risk of coronary heart disease (CHD), and a daily intake as low as possible is required to minimize health risks. To achieve this at the individual level in Denmark, legislation limited IP-TFA in foods...

  3. Editorial for the IEEE Transactions on Power Electronics, January 2009

    DEFF Research Database (Denmark)

    Blaabjerg, Frede

    2009-01-01

    I am entering the fourth year as the Editor in Chief of the IEEE TRANSACTIONS ON POWER ELECTRONICS. A position like this becomes more and more important for the technical field as publishing in a peer-reviewed highly ranked journal has influence on the industrial and academic career. It is a way...

  4. ARC Researchers at IEEE 2015 Vehicle Power and Propulsion Conference

    Science.gov (United States)

    Contacts Researchers News & Events Event Calendar Annual Program Review Research Seminars Press Room Event Archives ARC Researchers at the IEEE 2015 Vehicle Power and Propulsion Conference (October 19-22 Ballroom B P-SS4-2 Comparison of SOFC and PEM Fuel Cell Hybrid Power Management Strategies for Mobile

  5. Eleanor McElwee and the Formation of IEEE PCS

    Science.gov (United States)

    Malone, Edward A.

    2015-01-01

    This article examines the historical professional project that created the Institute of Radio Engineers' Professional Group on Engineering Writing an Speech (IRE PGEWS)--now called the Institute of Electrical and Electronics Engineers' Professional Communication Society (IEEE PCS)--and recounts the group's early history in detail. It also traces…

  6. 2011 IEEE Vehicular Networking Conference (VNC): Demo Summaries

    NARCIS (Netherlands)

    Altintas, O.; Chen, W.; Heijenk, Geert; Dressler, F.; Ekici, E.; Kargl, Frank; Shigeno, H.; Dietzel, Stefan

    2011-01-01

    Foreword For the first time in its history, IEEE VNC has included this year’s demonstrations in its program. Demonstrations play an important role to expose the research community to practical aspects of research and to foster cross-fertilization among researchers both in academia and in industry.

  7. 0011-0030.Data Representation amp Computer Arithmetic6 IEEE ...

    Indian Academy of Sciences (India)

    Home; public; Volumes; reso; 021; 01; 0011-0030.Data Representation amp Computer Arithmetic6 IEEE Standard Double Precision FormatIn.pdf. 404! error. The page your are looking for can not be found! Please check the link or use the navigation bar at the top. YouTube; Twitter; Facebook; Blog. Academy News.

  8. Ultrasonic colour Doppler imaging

    DEFF Research Database (Denmark)

    Evans, David H; Jensen, Jørgen Arendt; Nielsen, Michael Bachmann

    2011-01-01

    Ultrasonic colour Doppler is an imaging technique that combines anatomical information derived using ultrasonic pulse-echo techniques with velocity information derived using ultrasonic Doppler techniques to generate colour-coded maps of tissue velocity superimposed on grey-scale images of tissue...... anatomy. The most common use of the technique is to image the movement of blood through the heart, arteries and veins, but it may also be used to image the motion of solid tissues such as the heart walls. Colour Doppler imaging is now provided on almost all commercial ultrasound machines, and has been...

  9. Ultrasonic testing X gammagraphy

    International Nuclear Information System (INIS)

    Mello Campos, A.M. de

    1989-01-01

    The experience of 10 years for substituting gammagraphy tests by ultrasonic tests is related. A comparative evaluation of data obtained from both techniques applied to welded butt joints is presented. (author)

  10. Ultrasonic grinding method

    International Nuclear Information System (INIS)

    Miyahara, Shuji.

    1990-01-01

    An ultrasonic generator and a liquid supply nozzle are opposed to an object to be ground and a pump is started in this state to supply an organic solvent. Matters to be decontaminated which adheres to the surface of the object to be ground and are difficult to be removed by a mere mechanical removing method can be eliminated previously by the surface active effect of the organic solvent such as ethanol prior to the oscillation of the ultrasonic generator. Subsequently, when the ultrasonic generator is oscillated, scales in the floated state can be removed simply. Further, since the organic solvent can penetrate to provide the surface active effect even in such a narrow portion that the top end of the ultrasonic generator is difficult to the intruded at the surface of the object to be ground, the decontaminating treatment can be applied also to such a narrow portion. (T.M.)

  11. Fundamentals of Medical Ultrasonics

    CERN Document Server

    Postema, Michiel

    2011-01-01

    This book sets out the physical and engineering principles of acoustics and ultrasound as used for medical applications. It covers the basics of linear acoustics, wave propagation, non-linear acoustics, acoustic properties of tissue, transducer components, and ultrasonic imaging modes, as well as the most common diagnostic and therapeutic applications. It offers students and professionals in medical physics and engineering a detailed overview of the technical aspects of medical ultrasonic imaging, whilst serving as a reference for clinical and research staff.

  12. Assessing ultrasonic examination results

    International Nuclear Information System (INIS)

    Deutsch, V.; Vogt, M.

    1977-01-01

    Amongst nondestructive examination methods, the ultrasonic examination plays an important role. The reason why its scope of application is so wide is because the sound conducting capacity is the only property the material of a test specimen has to have. As the fields are so manifold, only main aspects can be described briefly. The list of references, however, is very extensive and gives plenty of information of all the problems concerning the assessment of ultrasonic examination results. (orig./RW) [de

  13. Qualification test of Class 1E equipment based on IEEE323 Std 2003

    International Nuclear Information System (INIS)

    Kim, J. S.; Jung, S. C.; Kim, T. R.

    2004-01-01

    IEEE Standard for Qualifying Class 1E Equipment has been updated to 2003 edition since the issue of IEEE Std 323-1971, 1974, 1983. NRC approved the IEEE Std 323-1974 as Qualification standard of Class 1E Equipment in domestic nuclear power plant. IEEE Std 323-2003 was issued in September of 2003 and utility is waiting the approval of NRC. IEEE Std 323-2003 suggest a new qualification technique which adopts the condition monitoring. Performance of two transient during DBA test is no longer recommended in IEEE Std 323-2003. IEEE323 Std 2003 included a chapter of ''extension of Qualified life'' to make available the life extension of components during plant life extension. For the efficient control of preserving EQ in domestic nuclear power plant, IEEE323 Std 2003 is strongly recommended

  14. Ultrasonic viewing device

    International Nuclear Information System (INIS)

    Ito, Juro.

    1979-01-01

    Purpose: To improve the safety of reactor operation by enabling to detect the states and positions of fuel assemblies over a wide range with a set of ultrasonic viewing device comprising a rotatable ultrasonic transmitter-receiver and a reflector mounted with an adjustable angle. Constitution: A driving portion for a ultrasonic viewing device is provided to a rotary plug closing the opening of a reactor vessel and a guide pipe suspending below the coolant level is provided to the driving portion. An ultrasonic transmitter-receiver is provided at the end of the holder tube in the guide pipe. A reflector is provided at the upper position of the reactor core so as to correspond to the ultrasonic transmitter-receiver. The ultrasonic transmitter-receiver, positioned by the driving portion, performs horizontal movement for scanning the entire surface of the top of the reactor core, as well as vertical movement covering the gap between the upper mechanism on the reactor and the reactor core, whereby the confirmation for the separation of the control rod and the detection for the states of the reactor core can be conducted by the reflection waves from the reflector. (Moriyama, K.)

  15. ULTRASONIC ASSEMBLY [REVIEW

    Directory of Open Access Journals (Sweden)

    PORAV Viorica

    2015-05-01

    Full Text Available The paper exposes the possibility of machine producesers to optimize the costs of clothes assembling. Ultrasonic systems being frequently utilized have many advantages on semi products of synthetic textile and technical textile. First of all, sewing – cutting process can be accomplished under high speeds and rate of losses can be minimized. Cutting seal applications are frequently used for underwear and sportswear. Slicing and unit cutting machines, as well as portable sealing machines are available for labeling sector. Products such as bag, pocket and cover can be sewed in a seamless manner for promotion purposes. All objects in terms of accessories are obtained in same standard. Our quilting machines are preferred in worldwide due to its threadless, high quality sealing. An alternative to the classic sewing assembly, with thread and needles is ultrasonic seaming. In ultrasonic welding, there are no connective bolts, nails, soldering materials, or adhesives necessary to bind the materials together. Ultrasonic is defined as acoustic frequencies above the range audible to the human ear. Ultrasonic frequencies are administered to the fabric from the sonotrode of bonding machine. The high frequency and powerful energy produced, when is release in one special environment, the ultrasound heating this environment. The ability to ultrasonic weld textiles and films depend on their thermoplastic contents and the desired end results. The paper defines the weld ability of more common textiles and films. The welding refers to all types of bonding and sealing, as in point bonding of fabric, or continuous sealing of film.

  16. Introduction to IEEE Std. 7-4.3.2 Annex D -- ''Qualification of existing commercial computers''

    International Nuclear Information System (INIS)

    Holmstrom, K.J.

    1995-01-01

    On September 15th of 1993 the IEEE standards board approved IEEE Std. 7-4.3.2-1993, IEEE Standard for Digital Computers in Safety Systems of Nuclear Power Generating Stations. This paper is an introduction to Annex D of this document which concerns the commercial grade dedication of existing computers or new non-1E computers

  17. IEEE C37.82-1987: IEEE standard for the qualification of switchgear assemblies for Class 1E applications in nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This document describes the methods and requirements for qualifying switchgear assemblies for indoor areas outside of the containment in nuclear power generating stations. These assemblies include (1) metal-enclosed low-voltage power circuit breaker switchgear assemblies, as defined in ANSI/IEEE C37.20.1-1987, (2) metal-clad switchgear assemblies, as defined in ANSI/IEEE C37.20.2-1987, (3) metal-enclosed bus, as defined in ANSI/IEEE C37.23-1987, and (4) metal-enclosed interrupter switchgear assemblies, as defined in ANSI/IEEE C37.20.3-1987. The purpose of this document is to provide amplification of the general requirements of ANSI/IEEE Std 323-1983 as they apply to the specific features of Class 1E switchgear assemblies. Where differences exist between this document and ANSI/IEEE Std 323-1983, this document takes precedence insofar as switchgear assemblies are concerned

  18. Proceedings of IEEE Machine Learning for Signal Processing Workshop XVI

    DEFF Research Database (Denmark)

    Larsen, Jan

    These proceedings contains refereed papers presented at the sixteenth IEEE Workshop on Machine Learning for Signal Processing (MLSP'2006), held in Maynooth, Co. Kildare, Ireland, September 6-8, 2006. This is a continuation of the IEEE Workshops on Neural Networks for Signal Processing (NNSP......). The name of the Technical Committee, hence of the Workshop, was changed to Machine Learning for Signal Processing in September 2003 to better reflect the areas represented by the Technical Committee. The conference is organized by the Machine Learning for Signal Processing Technical Committee...... the same standard as the printed version and facilitates the reading and searching of the papers. The field of machine learning has matured considerably in both methodology and real-world application domains and has become particularly important for solution of problems in signal processing. As reflected...

  19. IEEE prize awarded to CERN PhD student

    CERN Multimedia

    2006-01-01

    Rafael Ballabriga Suñe (right) receives the Student Paper Award. Rafael Ballabriga Suñe is the recipient of the 2006 Institute of Electrical and Electronics Engineers, Inc. (IEEE) Nuclear and Plasma Sciences Society (NPSS)'s Student Paper Award. Ballabriga's winning paper reported on a prototype chip, which belongs to a new generation of single photon counting hybrid pixel detector readout chips - Medipix3. The NPSS established this award in 2005 to encourage outstanding student contributions and greater student participation as principle or sole authors of papers. The prizes were presented at the IEEE Nuclear Science Symposium held in San Diego on 29 October to 4 November. The prototype chip was designed by Ballabriga based on ideas generated within the CERN Medipix team - part of the PH Microelectronics group. It could be used in various fields in the future, including medical imaging, neutron imaging, electron microscopy, radiation monitoring and other applications in high-energy physics. The novel aspe...

  20. IEEE 802.3 Fiber Optic Inter-Repeater Link

    Science.gov (United States)

    Tarrant, Peter J.

    1987-01-01

    This paper describes the implementation of a fiber optic inter-repeater link (FOIRL), used for connecting two remote copper segments of an IEEE 802.3 local area network. The rationale for the design, the signalling used and the collision detection mechanism is discussed. The evolution of the draft international standard for the FOIRL and the concurrence amongst various manufacturers is also presented. Finally some examples of typical applications, highlighting the ease of installation, are given.

  1. Basic security measures for IEEE 802.11 wireless networks

    OpenAIRE

    Sarmiento, Oscar P.; Guerrero, Fabio G.; Rey Argote, David

    2008-01-01

    This article presents a tutorial/discussion of three commonly-used IEEE 802.11 wireless network security standards: WEP, WPA and WPA2. A detailed analysis of the RC4 algorithm supporting WEP is presented, including its vulnerabilities. The WPA and WPA2 encryption protocols’ most relevant aspects and technical characteristics are reviewed for a comparative analysis of the three standards in terms of the security they provide. Special attention has been paid to WEP encryption by using an educat...

  2. 17th IEEE NPSS Real Time Conference – RT-2010

    CERN Multimedia

    Carlos Varandas

    2010-01-01

    Congress Centre of “Instituto Superior Técnico”, Lisboa, Portugal, 24-28 May, 2010 ABSTRACT SUBMISSION OPEN Abstract Submission Deadline: March 1st, 2010 Dear Sir/Madam, We are pleased to announce that abstract submission for the 17th IEEE NPSS Real Time Conference is now open on our web site. The deadline for submitting an abstract is 1st March 2010. Full conference details General Chairman

  3. Ultrasonic dip seal maintenance system

    International Nuclear Information System (INIS)

    Poindexter, A.M.; Ricks, H.E.

    1978-01-01

    Disclosed is a system for removing impurities from the surfaces of liquid dip seals and for wetting the metal surfaces of liquid dip seals in nuclear components. The system comprises an ultrasonic transducer that transmits ultrasonic vibrations along an ultrasonic probe to the metal and liquid surfaces of the dip seal thereby loosening and removing those impurities

  4. Artificial Intelligence Assists Ultrasonic Inspection

    Science.gov (United States)

    Schaefer, Lloyd A.; Willenberg, James D.

    1992-01-01

    Subtle indications of flaws extracted from ultrasonic waveforms. Ultrasonic-inspection system uses artificial intelligence to help in identification of hidden flaws in electron-beam-welded castings. System involves application of flaw-classification logic to analysis of ultrasonic waveforms.

  5. Ultrasonic Stir Welding

    Science.gov (United States)

    Nabors, Sammy

    2015-01-01

    NASA Marshall Space Flight Center (MSFC) developed Ultrasonic Stir Welding (USW) to join large pieces of very high-strength metals such as titanium and Inconel. USW, a solid-state weld process, improves current thermal stir welding processes by adding high-power ultrasonic (HPU) energy at 20 kHz frequency. The addition of ultrasonic energy significantly reduces axial, frictional, and shear forces; increases travel rates; and reduces wear on the stir rod, which results in extended stir rod life. The USW process decouples the heating, stirring, and forging elements found in the friction stir welding process allowing for independent control of each process element and, ultimately, greater process control and repeatability. Because of the independent control of USW process elements, closed-loop temperature control can be integrated into the system so that a constant weld nugget temperature can be maintained during welding.

  6. Ultrasonic nondestructive materials characterization

    Science.gov (United States)

    Green, R. E., Jr.

    1986-01-01

    A brief review of ultrasonic wave propagation in solid materials is presented with consideration of the altered behavior in anisotropic and nonlinear elastic materials in comparison with isotropic and linear elastic materials. Some experimental results are described in which ultrasonic velocity and attenuation measurements give insight into materials microstructure and associated mechanical properties. Recent developments with laser beam non-contact generation and detection of ultrasound are presented. The results of several years of experimental measurements using high-power ultrasound are discussed, which provide substantial evidence of the inability of presently accepted theories to fully explain the interaction of ultrasound with solid materials. Finally, a special synchrotron X-ray topographic system is described which affords the possibility of observing direct interaction of ultrasonic waves with the microstructural features of real crystalline solid materials for the first time.

  7. Ultrasonic colour Doppler imaging

    DEFF Research Database (Denmark)

    Evans, David H.; Jensen, Jørgen Arendt; Nielsen, Michael Bachmann

    2011-01-01

    Ultrasonic colour Doppler is an imaging technique that combines anatomical information derived using ultrasonic pulse-echo techniques with velocity information derived using ultrasonic Doppler techniques to generate colour-coded maps of tissue velocity superimposed on grey-scale images of tissue...... anatomy. The most common use of the technique is to image the movement of blood through the heart, arteries and veins, but it may also be used to image the motion of solid tissues such as the heart walls. Colour Doppler imaging is now provided on almost all commercial ultrasound machines, and has been...... vectors. This review briefly introduces the principles behind colour Doppler imaging and describes some clinical applications. It then describes the basic components of conventional colour Doppler systems and the methods used to derive velocity information from the ultrasound signal. Next, a number of new...

  8. Ultrasonic tests. Pt. 2

    International Nuclear Information System (INIS)

    Goebbels, K.

    1980-01-01

    After a basic treatment of ultrasonic wave propagation, of the state-of-the-art methods and the technical background in the preceeding part, advanced ultrasonic NDT techniques are presented here. The discussion of new development includes - manipulation systems, - automation of ultrasonic testing methods, documentation and evaluation. In the middle of this part the main problem areas will be discussed: - detection of defects (e.g. in coarse grained structures and welds), - classification of defects (e.g. discrimination between crack-like and volumetric faults), - sizing of defects. Research in the field of acoustical holography, development of probes and phased arrays, electromagnetic acoustic transducers and signal enhancement are the main contributing parts to the report. (orig./RW)

  9. Proceedings IEEE Visualization Conference and IEEE Information Visualization Conference (VIS'07 and INFOVIS'07, Sacramento CA, USA, October 28-November 1, 2007)

    NARCIS (Netherlands)

    Chen, M.; Hansen, C.; North, C.; Pang, A.; Wijk, van J.J.

    2007-01-01

    These are the proceedings of the IEEE Visualization Conference 2007 (Vis 2007) and the IEEE Information Visualization Conference 2007 (InfoVis 2007) held during October 28 to November 1, 2007 in Sacramento, California. The power of using computing technology to create useful, effective imagery for

  10. Coexistence of IEEE 802.11b/g WLANs and IEEE 802.15.4 WSNs : Modeling and Protocol Enhancements

    NARCIS (Netherlands)

    Yuan, W.

    2011-01-01

    As an emerging short-range wireless technology, IEEE 802.15.4/ZigBee Wireless Sensor Networks (WSNs) are increasingly used in the fields of home control, industrial control, consumer electronics, energy management, building automation, telecom services, personal healthcare, etc. IEEE

  11. Ultrasonic weld testing.

    Science.gov (United States)

    1970-12-01

    The study was broken down into two phases. Phase I consisted of a laboratory investigation of test specimens to determine the reliability of the ultrasonic equipment and testing procedure. Phase II was a field study where the knowledge, skills and ab...

  12. Ultrasonic leak detection

    International Nuclear Information System (INIS)

    Murphy, R.V.

    1977-01-01

    A scanning ultrasonic microphone was used to detect the presence and locate the sources of hydraulic noises in piping systems in a reactor environment. The intensity changes of the noises correspond to changes of flow conditions within the system caused by throttled valves, flow rate changes, and leaks. (author)

  13. Radical feminists & trans activists truce

    OpenAIRE

    Mackay, F.

    2014-01-01

    #GenderWeek: Truce! When radical feminists and trans feminists empathise\\ud Feminist Times\\ud By Finn Mackay \\ud read all #GenderWeek articles.\\ud We wanted to explore the ground between the polarised, entrenched positions in the so-called “TERF-war”. Radical feminists on one pole, trans-inclusionary feminists and trans activists on the other. The disputed territory being women-only space, language and the ever changing legal framework surrounding gender.\\ud Entrenchment leads to stalemate. S...

  14. Ultrasonic Bat Deterrent Technology

    Energy Technology Data Exchange (ETDEWEB)

    Kinzie, Kevin; Rominger, Kathryn M.

    2017-12-14

    The project objective was to advance the development and testing of an Near commercial bat-deterrent system with a goal to increase the current GE deterrent system effectiveness to over 50% with broad species applicability. Additionally, the research supported by this program has provided insights into bat behavior and ultrasonic deterrent design that had not previously been explored. Prior research and development had demonstrated the effectiveness of a commercial-grade, air-powered, ultrasonic bat deterrent to be between 30-50% depending upon the species of bat. However, the previous research provided limited insight into the behavioral responses of bats in the presence of ultrasonic deterrent sound fields that could be utilized to improve effectiveness. A unique bat flight room was utilized to observe the behavioral characteristics of bats in the presence of ultrasonic sound fields. Behavioral testing in the bat flight facility demonstrated that ultrasonic sounds similar to those produced by the GE deterrent influenced the activities and behaviors, primarily those associated with foraging, of the species exposed. The study also indicated that continuous and pulsing ultrasonic signals had a similar effect on the bats, and confirmed that as ultrasonic sounds attenuate, their influence on the bats’ activities and behavior decreases. Ground testing at Wolf Ridge Wind, LLC and Shawnee National Forest assessed both continuous and pulsing deterrent signals emitted from the GE deterrent system and further enhanced the behavioral understanding of bats in the presence of the deterrent. With these data and observations, the existing 4-nozzle continuous, or steady, emission ultrasonic system was redesigned to a 6-nozzle system that could emit a pulsing signal covering a larger air space around a turbine. Twelve GE 1.6-100 turbines were outfitted with the deterrent system and a formal three-month field study was performed using daily carcass searches beneath the 12

  15. 15th IEEE International Conference on Intelligent Engineering Systems

    CERN Document Server

    Živčák, Jozef; Aspects of Computational Intelligence Theory and Applications

    2013-01-01

    This volume covers the state-of-the art of the research and development in various aspects of computational intelligence and gives some perspective directions of development. Except the traditional engineering areas that contain theoretical knowledge, applications, designs and projects, the book includes the area of use of computational intelligence in biomedical engineering. „Aspects of Computational Intelligence: Theory and Applications” is a compilation of carefully selected extended papers written on the basis of original contributions presented at the 15th IEEE International Conference on Intelligent Engineering Systems 2011, INES 2011 held at June 23.-26. 2011 in AquaCity Poprad, Slovakia.    

  16. Status of the IEEE P896 Future Backplane Bus

    International Nuclear Information System (INIS)

    Gustavson, D.B.

    1983-10-01

    The IEEE P896 Future Backplane Bus project has been influenced by and has influenced FASTBUS and several other contemporary bus designs. This paper summarizes the current status of that project, which is directed toward the needs of modern 32-bit microprocessor systems with multiple processors. Some of the technology developed for P896 will be important for future non-ECL implementations of FASTBUS and other buses. In particular, new bus drivers and receivers should greatly improve the performance and reliability of backplane buses and cable buses. The current status of the P896 serial bus is also summarized

  17. Extending Service Area of IEEE 802.11 Ad Hoc Networks

    Science.gov (United States)

    Choi, Woo-Yong

    2012-06-01

    According to the current IEEE 802.11 wireless LAN standards, IEEE 802.11 ad hoc networks have the limitation that all STAs (Stations) are in the one-hop transmission range of each other. In this paper, to alleviate the limitation of IEEE 802.11 ad hoc networks we propose the efficient method for selecting the most appropriate pseudo AP (Access Point) from among the set of ad hoc STAs and extending the service area of IEEE 802.11 ad hoc networks by the pseudo AP's relaying the internal traffic of IEEE 802.11 ad hoc networks. Numerical examples show that the proposed method significantly extends the service area of IEEE 802.11 ad hoc networks.

  18. IEEE Std 649-1991: IEEE standard for qualifying Class 1E motor control centers for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    The basic principles, requirements, and methods for qualifying Class 1E motor control centers for both harsh and mild environment applications in nuclear power generating stations are described. In addition to defining specific qualification requirements for Class 1E motor control centers and their components in accordance with the more general qualification requirements of IEEE Std 323-1983, this standard is intended to provide guidance in establishing a qualification program for demonstrating the adequacy of Class 1E motor control centers in nuclear power generating station applications

  19. The ultrasonic relaxation spectra for furfural molecules undergoing conformational changes

    International Nuclear Information System (INIS)

    Mirzaev, S. Z.; Telyaev, S. Q.; Egamberdiev, K.

    2011-01-01

    The acoustic spectra of liquid furfural have been investigated in the frequency range from 0.1MHz to 150 MHz and at the temperatures from 303.15 K to 333.15 K. The ultrasonic spectra of pure furfural show two relaxation processes. One relaxation process is located in the frequency range ∼0.2 MHz, and the second in the frequency range ∼2 MHz. The process with the lower relaxation frequency has been assigned to the 'X0-cis and X0-trans' internal rotation of furfural molecules. (authors)

  20. IEEE Standard for qualification of Class 1E lead storage batteries for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    This document describes qualification methods for Class 1E lead storage batteries and racks to be used in nuclear power generating stations outside of primary containment. Qualification required in ANSI/IEEE Std 279-1979 and IEEE Std 308-1978, can be demonstrated by using the procedures provided in this Standard in accordance with IEEE Std 323-1974. Battery sizing, maintenance, capacity testing, installation, charging equipment and consideration of other types batteries are beyond the scope of this Standard

  1. IEEE standard for qualification of class 1E lead storage batteries for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1979-01-01

    IEEE Std 323-1974, Standard for Qualifying Class 1E Equipment for Nuclear Power Generating Stations, was developed to provide guidance for demonstrating and documenting the adequacy of electrical equipment used in all Class 1E and interface systems. This standard, IEEE Std 535-1979, was developed to provide specific methods and type test procedures for lead storage batteries in reference to IEEE Std 323-1974

  2. Ultrasonic calibration assembly

    International Nuclear Information System (INIS)

    1981-01-01

    Ultrasonic transducers for in-service inspection of nuclear reactor vessels have several problems associated with them which this invention seeks to overcome. The first is that of calibration or referencing a zero start point for the vertical axis of transducer movement to locate a weld defect. The second is that of verifying the positioning (vertically or at a predetermined angle). Thirdly there is the problem of ascertaining the speed per unit distance in the operating medium of the transducer beam prior to the actual inspection. The apparatus described is a calibration assembly which includes a fixed, generally spherical body having a surface for reflecting an ultrasonic beam from one of the transducers which can be moved until the reflection from the spherical body is the highest amplitude return signal indicating radial alignment from the body. (U.K.)

  3. Pulsed ultrasonic stir welding system

    Science.gov (United States)

    Ding, R. Jeffrey (Inventor)

    2013-01-01

    An ultrasonic stir welding system includes a welding head assembly having a plate and a rod passing through the plate. The rod is rotatable about a longitudinal axis thereof. During a welding operation, ultrasonic pulses are applied to the rod as it rotates about its longitudinal axis. The ultrasonic pulses are applied in such a way that they propagate parallel to the longitudinal axis of the rod.

  4. Poster abstract: Water level estimation in urban ultrasonic/passive infrared flash flood sensor networks using supervised learning

    KAUST Repository

    Mousa, Mustafa

    2014-04-01

    This article describes a machine learning approach to water level estimation in a dual ultrasonic/passive infrared urban flood sensor system. We first show that an ultrasonic rangefinder alone is unable to accurately measure the level of water on a road due to thermal effects. Using additional passive infrared sensors, we show that ground temperature and local sensor temperature measurements are sufficient to correct the rangefinder readings and improve the flood detection performance. Since floods occur very rarely, we use a supervised learning approach to estimate the correction to the ultrasonic rangefinder caused by temperature fluctuations. Preliminary data shows that water level can be estimated with an absolute error of less than 2 cm. © 2014 IEEE.

  5. Proceedings of the IEEE Machine Learning for Signal Processing XVII

    DEFF Research Database (Denmark)

    The seventeenth of a series of workshops sponsored by the IEEE Signal Processing Society and organized by the Machine Learning for Signal Processing Technical Committee (MLSP-TC). The field of machine learning has matured considerably in both methodology and real-world application domains and has...... become particularly important for solution of problems in signal processing. As reflected in this collection, machine learning for signal processing combines many ideas from adaptive signal/image processing, learning theory and models, and statistics in order to solve complex real-world signal processing......, and two papers from the winners of the Data Analysis Competition. The program included papers in the following areas: genomic signal processing, pattern recognition and classification, image and video processing, blind signal processing, models, learning algorithms, and applications of machine learning...

  6. Editorial for IEEE Transactions on Power Electronics, January 2013

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Lehman, Brad

    2013-01-01

    should increase the impact factor of the IEEE TRANSACTIONS ON POWER ELECTRONICS (TPEL). In 2007, TPEL published 2600 pages, and it has gradually been increased to 4000 pages in 2011, 5000 pages in 2012, and 5500 pages are projected for 2013. We have decided to publish 12 printed issues so every month...... a new issue will be printed. A graph is provided showing the number of regular papers received in the past years as well as the number of published pages in the TPEL. Finally they note that in 2008, TPEL obtained a record high value for the impact factor (as shown in a figure) but in 2009 it was reduced...... the papers to be read over a longer time span; 2) Web of Science (ISI Thomsen Reuter) began to register new power electronics conferences in their database, and citations from conferences counts and contributes to a higher impact factor....

  7. Report of the 2017 IEEE Cyber Science and Technology Congress

    Directory of Open Access Journals (Sweden)

    Wenbing Zhao

    2017-12-01

    Full Text Available The modern digitized world has led to the emergence of a new paradigm on global information networks and infrastructures known as Cyberspace and the studies of Cybernetics, which bring seamless integration of physical, social and mental spaces. Cyberspace is becoming an integral part of our daily life from learning and entertainment to business and cultural activities. As expected, this whole concept of Cybernetics brings new challenges that need to be tackled. The 2017 IEEE Cyber Science and Technology Congress (CyberSciTech 2017 provided a forum for researchers to report their research findings and exchange ideas. The congress took place in Orlando, Florida, USA during 6–10 November 2017. Not counting poster papers, the congress accepted over fifty papers that are divided into nine sessions. In this report, we provide an overview of the research contributions of the papers in CyberSciTech 2017.

  8. WIH-based IEEE 802.11 ECG monitoring implementation.

    Science.gov (United States)

    Moein, A; Pouladian, M

    2007-01-01

    New wireless technologies make possible the implementation of high level integration wireless devices which allow the replacement of traditional large wired monitoring devices. It offers new functionalities to physicians and will reduce the costs. Among these functionalities, biomedical signals can be sent to other devices (PDA, PC . . . ) or processing centers, without restricting the patients' mobility. This article discusses the WIH (Ward-In-Hand) structure and the software required for its implementation before an operational example is presented with its results. The aim of this project is the development and implementation of a reduced size electrocardiograph based on IEEE 802.11 with high speed and more accuracy, which allows wireless monitoring of patients, and the insertion of the information into the Wi-Fi hospital networks.

  9. Basic security measures for IEEE 802.11 wireless networks

    Directory of Open Access Journals (Sweden)

    Oscar P. Sarmiento

    2008-05-01

    Full Text Available This article presents a tutorial/discussion of three commonly-used IEEE 802.11 wireless network security standards: WEP, WPA and WPA2. A detailed analysis of the RC4 algorithm supporting WEP is presented, including its vulnera-bilities. The WPA and WPA2 encryption protocols’ most relevant aspects and technical characteristics are reviewed for a comparative analysis of the three standards in terms of the security they provide. Special attention has been paid to WEP encryption by using an educational simulation tool written in C++ Builder for facilitating the unders-tanding of this protocol at academic level. Two practical cases of wireless security configurations using Cisco net-working equipment are also presented: configuring and enabling WPA-Personal and WPA2-Personal (these being security options used by TKIP and AES, respectively.

  10. IEEE Std 535-1979: IEEE standard for qualification of Class 1E lead storage batteries for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This document describes qualification methods for Class 1E lead storage batteries and racks to be used in nuclear power generating stations outside of primary containment. Qualification required in ANSI/IEEE Std 279-1971 and IEE Std 308-1978, can be demonstrated by using the procedures provided in this standard in accordance with IEEE Std 323-1974. Battery sizing, maintenance, capacity testing, installation, charging equipment and consideration of other type batteries are beyond the scope of this standard

  11. IEEE Std 535-1986: IEEE standard for qualification of Class 1E lead storage batteries for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This document describes qualification methods for Class 1E lead storage batteries and racks to be used in nuclear power generating stations outside of primary containment. Qualification required in ANSI/IEEE Std 308-1980 can be demonstrated by using the procedures provided in this standard in accordance with ANSI/IEEE Std 323-1983. Battery sizing, maintenance, capacity testing, installation, charging equipment, and consideration of other type batteries are beyond the scope of this standard

  12. IEEE Std 650-1990: IEEE standard for qualification of Class 1E static battery chargers and inverters for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Methods for qualifying static battery chargers and inverters for Class 1E installations in a mild environment outside containment in nuclear power generating stations are described. The qualification methods set forth employ a combination of type testing and analysis, the latter including a justification of methods, theories, and assumptions used. These procedures meet the requirements of IEEE Std 323-1983, IEEE Standard for Qualifying Class 1E Equipment for Nuclear Power Generating Stations

  13. A formal analysis of ISO/IEEE P11073-20601 standard of medical device communication

    NARCIS (Netherlands)

    Goga, Nicolae; Costache, Stefania; Moldoveanu, Florica

    2009-01-01

    This article presents the formal work done for the ISO/IEEE P11073-20601 Draft Standard for Health informatics - Personal health device communication - Application profile Optimized exchange protocol. ISO/IEEE 11073 family defines standards for device communication between agents (e.g. blood

  14. Comparison Of Several Methods Of Implementing A Fiber Optic IEEE 802.3 Ethernet

    Science.gov (United States)

    Thompson, Geoffrey O.

    1987-01-01

    Several different methods of implementing a fiber optic version of IEEE 802.3 10BASE LANs have been proposed as a candidate for standardization by IEEE. There have been extensive discussions as to the relative merits and features of the several systems. This paper will discuss the merits of each for this particular application on a comparative basis.

  15. 0011-0030.How to make an abstract in IEEE Format for ...

    Indian Academy of Sciences (India)

    Home; public; Volumes; reso; 021; 01; 0011-0030.How to make an abstract in IEEE Format for AvishkarMulticultural Night in IEEE R10 Student Congress 2009Performances.pdf. 404! error. The page your are looking for can not be found! Please check the link or use the navigation bar at the top. YouTube; Twitter; Facebook ...

  16. 0011-0030.What is IEEE 754 StandardHow to convert real number ...

    Indian Academy of Sciences (India)

    Home; public; Volumes; reso; 021; 01; 0011-0030.What is IEEE 754 StandardHow to convert real number in binary format using IEEE 754 StandardAn.pdf. 404! error. The page your are looking for can not be found! Please check the link or use the navigation bar at the top. YouTube; Twitter; Facebook; Blog. Academy News.

  17. Trans fatty acid isomers and the trans-9/trans-11 index in fat containing foods

    Science.gov (United States)

    Kuhnt, Katrin; Baehr, Melanie; Rohrer, Carsten; Jahreis, Gerhard

    2011-01-01

    To determine trans fatty acid (TFA) distribution of contemporary foods, especially regarding individual trans octadecenoic acids (trans C18:1), 339 German foods of six categories (semi-solid fats, deep-fried potato products, bakery products, confectioneries, instant products and butter) were analysed using two GC methods. Results showed a high variation of TFA content between and within the categories containing between 0 and 40.5% of FAME except in butter, which is a source of natural TFA. The mean TFA values were below 2.0% of FAME, however, bakery products contained 4.5% and butter fat 3.2%, respectively. In addition, the distribution of individual trans C18:1 differed. In samples containing ruminant fat (butter and various confectioneries), vaccenic acid (t11-C18:1, t11) predominated, while in foods containing industrially hydrogenated fats, elaidic acid (trans-9, t9-) and t10-C18:1 were the major trans isomers.. This was reflected by a low t9/t11 index of 0.3 and 0.5 in butter and ruminant fat containing confectioneries, respectively, whilst the highest index was observed in shortenings and deep-fried potato products at 5.2 and 6.8, respectively. In conclusion, the TFA content of foods available on the German market is generally declining, but substantial variations are present. The t9/t11 index could be used as an indicator to determine ruminant fat. Practical applications: A number of studies provide evidence that a high TFA intake, particularly of industrial origin, adversely affects human health. The TFA content of foods could be reduced due to the introduction of several mandatory regulations and modifications regarding the hydrogenation process of oils. The most abundant dietary TFA are the isomers of trans C18:1. Unfortunately, the differentiation of these isomers is not yet very common, though the trans C18:1 profile differs depending on its origin (bacterial hydrogenation in the rumen or industrial hydrogenation). To date, data for TFA content

  18. IEEE Std 323-1983: IEEE standard for qualifying Class 1E equipment for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This standard describes the basic requirements for qualifying Class 1E equipment with interfaces that are to be used in nuclear power generating stations. The requirements presented include the principles, procedures, and methods of qualification. These qualification requirements, when met, will confirm the adequacy of the equipment design under normal, abnormal, design basis event, post design basis event, and in-service test conditions for the performance of safety function(s). The purpose of this standard is to identify requirements for the qualification of Class 1E equipment, including those interfaces whose failure could adversely affect the performance of Class 1E equipment and systems. The methods described shall be used for qualifying equipment, extending qualification, and updating qualification if the equipment is modified. Other issued IEEE standards which present qualification methods for specific equipment or components, or both, and those that deal with parts of the qualification program, may be used to supplement this standard, as applicable

  19. IEEE Std 649-1980: IEEE standard for qualifying Class 1E motor control centers for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This standard describes the basic principles, requirements, and methods for qualifying Class 1E motor control centers for outside containment applications in nuclear power generating stations. Qualification of motor control centers located inside containment in a nuclear power generating station is beyond the scope of this standard. The purpose of this standard is (1) to define specific qualification requirements for Class 1E motor control centers in accordance with the more general qualification requirements of IEEE Std 323-1974, IEE Standard for Qualifying Class 1E Equipment for Nuclear Power Generating Stations; (2) to provide guidance in establishing a qualification program for demonstrating the design adequacy of Class 1E motor control centers in nuclear power generating station applications

  20. Performance Analysis of IEEE 802.11 DCF and IEEE 802.11e EDCA in Non-saturation Condition

    Science.gov (United States)

    Kim, Tae Ok; Kim, Kyung Jae; Choi, Bong Dae

    We analyze the MAC performance of the IEEE 802.11 DCF and 802.11e EDCA in non-saturation condition where device does not have packets to transmit sometimes. We assume that a flow is not generated while the previous flow is in service and the number of packets in a flow is geometrically distributed. In this paper, we take into account the feature of non-saturation condition in standards: possibility of transmission performed without preceding backoff procedure for the first packet arriving at the idle station. Our approach is to model a stochastic behavior of one station as a discrete time Markov chain. We obtain four performance measures: normalized channel throughput, average packet HoL (head of line) delay, expected time to complete transmission of a flow and packet loss probability. Our results can be used for admission control to find the optimal number of stations with some constraints on these measures.

  1. Attacks on IEEE 802.11 wireless networks

    Directory of Open Access Journals (Sweden)

    Dejan Milan Tepšić

    2013-06-01

    Full Text Available Security of wireless computer networks was initially secured with the WEP security protocol, which relies on the RC4 encryption algorithm and the CRC algorithm to check the integrity. The basic problems of the WEP are a short initialization vector, unsafe data integrity checking, using a common key, the lack of mechanisms for management and exchange of keys, the lack of protection from the endless insertion of the same package into the network, the lack of authentication of access points and the like. The consequences of these failures are easy attacks against the WEP network, namely their complete insecurity. Therefore, the work began on the IEEE 802.11i protocol, which should radically improve the security of wireless networks. Since the development of a protocol lasted, the WPA standard was released to offset the security gap caused by the WEP. The WPA also relies on RC4 and CRC algorithms, but brings temporary keys and the MIC algorithm for data integrity. The 802.1X authentication was introduced and common keys are no longer needed, since it is possible to use an authentication server. The length of the initialization vector was increased and the vector is obtained based on the packet serial number, in order to prevent the insertion of the same packet into the network. The weakness of the WPA security mechanism is the use of a common key. WPA2 (802.11i later appeared. Unlike the WPA mechanism that worked on old devices with the replacement of software, WPA2 requires new network devices that can perform AES encryption. AES replaces the RC4 algorithm and delivers much greater security. Data integrity is protected by encryption. Despite progress, there are still weaknesses in wireless networks. Attacks for denial of service are possible as well as spoofing package headers attacks. For now, it is not advisable to use wireless networks in environments where unreliability and unavailability are not tolerated. Introduction In the entire history of

  2. Ultrasonic attenuation in superconducting zinc

    International Nuclear Information System (INIS)

    Auluck, S.

    1978-01-01

    The differences in the Zn ultrasonic attenuation data of different workers are analyzed. The superconducting energy gaps deduced from our analysis of the ultrasonic-attenuation data of Cleavelin and Marshall are consistent with the gaps deduced from the knowledge of the Fermi surface and the electron-phonon mass enhancement factor

  3. Lumber defect detection by ultrasonics

    Science.gov (United States)

    K. A. McDonald

    1978-01-01

    Ultrasonics, the technology of high-frequency sound, has been developed as a viable means for locating most defects In lumber for use in digital form in decision-making computers. Ultrasonics has the potential for locating surface and internal defects in lumber of all species, green or dry, and rough sawn or surfaced.

  4. Ultrasonic inspection of austenitic welds

    International Nuclear Information System (INIS)

    Baikie, B.L.; Wagg, A.R.; Whittle, M.J.; Yapp, D.

    1976-01-01

    The ultrasonic examination of austenitic stainless steel weld metal has always been regarded as a difficult proposition because of the large and variable ultrasonic attenuations and back scattering obtained from apparently similar weld deposits. The work to be described shows how the existence of a fibre texture within each weld deposit (as a result of epitaxial growth through successive weld beads) produces a systematic variation in the ultrasonic attenuation coefficient and the velocity of sound, depending upon the angle between the ultrasonic beam and the fibre axis. Development work has shown that it is possible to adjust the welding parameters to ensure that the crystallographic texture within each weld is compatible with improved ultrasonic transmission. The application of the results to the inspection of a specific weld in type 316 weld metal is described

  5. Ultrasonic variables affecting inspection

    International Nuclear Information System (INIS)

    Lautzenheiser, C.E.; Whiting, A.R.; McElroy, J.T.

    1977-01-01

    There are many variables which affect the detection of the effects and reproducibility of results when utilizing ultrasonic techniques. The most important variable is the procedure, as this document specifies, to a great extent, the controls that are exercised over the other variables. The most important variable is personnel with regards to training, qualification, integrity, data recording, and data analysis. Although the data is very limited, these data indicate that, if the procedure is carefully controlled, reliability of defect detection and reproducibility of results are both approximately 90 percent for reliability of detection, this applies to relatively small defects as reliability increases substantially as defect size increases above the recording limit. (author)

  6. Enhancing Biodiesel from Kemiri Sunan Oil Manufacturing using Ultrasonics

    Science.gov (United States)

    Supriyadi, Slamet; Purwanto; Anggoro, Didi Dwi; Hermawan

    2018-02-01

    Kemiri Sunan (Reutalis trisperma (Blanco) Airy Shaw) is a potential plant to be developed as biodiesel feedstock. The advantage of Kemiri Sunan seeds when compared to other biodiesel raw materials is their high oil content. This plant is also very good for land conservation. Due the increasingly demand for biodiesel, research and new methods to increase its biodiesel production continue to be undertaken. The weakness of conventional biodiesel manufacturing process is in the mixing process in which mechanical stirring and heating in the trans-esterification process require more energy and a longer time. A higher and stronger mixing process is required to increase the contact area between the two phases of the mixed substance to produce the emulsion. Ultrasonic is a tool that can be useful for a liquid mixing process that tends to be separated. Ultrasonic waves can cause mixing intensity at the micro level and increase mass transfer, so the reaction can be performed at a much faster rate. This study is to figure out the effect of ultrasonic irradiation on the transesterification process of biodiesel from Kemiri Sunan Oil.

  7. Advanced ultrasonic inspections

    International Nuclear Information System (INIS)

    Ghia, S.

    1990-08-01

    Acoustic Emission (AE) continuous monitoring and periodical inspections by advanced ultrasonic have been applied to evaluate defect evolution within a PWR reduced scale (1:5) pressure vessel subjected to cyclic mechanical fatigue test. This experimental activity has been carried out in the frame of the Primary Circuit Component Life Prediction programme. In the time period covered by this report actions were performed as following: (1) Ultrasonic examination by multifrequency acoustic holography to evaluate defect evolution subsequently repair and heat treatment of the R2 vessel carried out in March 1988. For the purpose, measurements were performed both at 0 and 200 bar of internal pressure. As uniformity of the procedures adopted, for calibration and testing, made the results comparable with the previous ones no evidence for significant growing of the examined defects has been found. (2) Acoustic emission monitoring has then been carried out during fatigue test from 416000 to 565000 fatigue cycles. Analysis of a large amount of data has been performed paying particular attention to the distinction between friction phenomena and crack growth in order to obtain a correct diagnosis of flaw evolution. The signal duration distribution and the correlation of AE appearance time versus load cycle phase were considered to characterise stick-slip processes. A general intensification of AE activity has been recorded during this last period of monitoring and previous known AE sources were confirmed together with the appearance of new AE sources some of them correlable with real defects

  8. System for ultrasonic examination

    International Nuclear Information System (INIS)

    Lund, S.A.; Kristensen, W.D.

    1987-01-01

    A computerized system for the recording of flaw images by ultrasonic examination according to the pulse-echo method includes at least one ultrasonic probe which can be moved in steps over the surface of an object along a rectilinear scanning path. Digital signals containing information on the successive positions of the sound beam, on echo amplitudes, and on the lengths of sound paths to reflectors inside the object, are processed and used for the accumulated storage of circular patterns of echo amplitude data in a matrix memory associated with a sectional plane through the object. A video screen terminal controls the system and transforms the accumulated data into displays of sectional flaw images of greatly improved precision and sharpness of definition. A gradual transfer of filtered data from a number of parallel sectional planes to three further matrix memories associated with projection planes at right angles to each other permits presentation in three dimensions of equally improved projection flaw images. (author) 2 figs

  9. IEEE Std 730 Software Quality Assurance: Supporting CMMI-DEV v1.3, Product and Process Quality Assurance

    Science.gov (United States)

    2011-05-27

    frameworks 4 CMMI-DEV IEEE / ISO / IEC 15288 / 12207 Quality Assurance ©2011 Walz IEEE Life Cycle Processes & Artifacts • Systems Life Cycle Processes...TAG to ISO TC 176 Quality Management • Quality: ASQ, work experience • Software: three books, consulting, work experience • Systems: Telecom & DoD...and IEEE 730 SQA need to align. The P730 IEEE standards working group has expanded the scope of the SQA process standard to align with IS 12207

  10. Imaging techniques for ultrasonic testing

    International Nuclear Information System (INIS)

    2013-01-01

    These seminar proceedings contain 16 lectures on the following topics: 1. From imaging to quantification - ultrasound methods in medical diagnostics; 2. SAFT, TOFD, Phased Array - classical applications and recent developments in ultrasonic imaging; 3. Innovative ultrasonic imaging methods in research and application; 4. Industrial ultrasonic testing of fibre-reinforced structures of complex geometry; 5. Visualisation of crack tips in the inspection of wheel set shafts with longitudinal boreholes as a means of avoiding unnecessary wheel set changes; 6. Areal analysis of the propagation of Lamb waves on curved, anisotropic structures; 7. High-resolution representation in immersion technique testing; 8. Variants in generating images from phased array measurement data - practical examples involving copper, carbon-fibre reinforced plastic and other materials; 9. GIUM - an unconventional method of microstructure imaging using ultrasonic stimulation and laser vibrometry scanning; 10. Innovative air-ultrasonic testing concepts for improved imaging; 11. Use of imaging methods for improving the quality of test results from nondestructive testing; 12. Modelling and visualisation of EMUS stimulation for transducer optimisation; 13. Use of SAFT in the manufacture of energy conversion machines; 14. Ultrasonic imaging tests for improved defect characterisation during weld seam inspection on longitudinally welded large-diameter pipes; 15. SAFT reconstruction for testing austenitic weld seams and dissimilar metal weld seams for transverse cracks; 16. Imaging-based optimisation method for quantitative ultrasonic testing of anisotropic inhomogeneous austenitic welded joints with determination and utilisation of their elastic properties. One contribution has been abstracted separately. [de

  11. IEEE 802.11ah: A Technology to Face the IoT Challenge.

    Science.gov (United States)

    Baños-Gonzalez, Victor; Afaqui, M Shahwaiz; Lopez-Aguilera, Elena; Garcia-Villegas, Eduard

    2016-11-22

    Since the conception of the Internet of things (IoT), a large number of promising applications and technologies have been developed, which will change different aspects in our daily life. This paper explores the key characteristics of the forthcoming IEEE 802.11ah specification. This future IEEE 802.11 standard aims to amend the IEEE 802.11 legacy specification to support IoT requirements. We present a thorough evaluation of the foregoing amendment in comparison to the most notable IEEE 802.11 standards. In addition, we expose the capabilities of future IEEE 802.11ah in supporting different IoT applications. Also, we provide a brief overview of the technology contenders that are competing to cover the IoT communications framework. Numerical results are presented showing how the future IEEE 802.11ah specification offers the features required by IoT communications, thus putting forward IEEE 802.11ah as a technology to cater the needs of the Internet of Things paradigm.

  12. 48 CFR 52.223-16 - IEEE 1680 Standard for the Environmental Assessment of Personal Computer Products.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false IEEE 1680 Standard for the... CONTRACT CLAUSES Text of Provisions and Clauses 52.223-16 IEEE 1680 Standard for the Environmental Assessment of Personal Computer Products. As prescribed in 23.706(b)(1), insert the following clause: IEEE...

  13. An Asynchronous IEEE Floating-Point Arithmetic Unit

    Directory of Open Access Journals (Sweden)

    Joel R. Noche

    2007-12-01

    Full Text Available An asynchronous floating-point arithmetic unit is designed and tested at the transistor level usingCadence software. It uses CMOS (complementary metal oxide semiconductor and DCVS (differentialcascode voltage switch logic in a 0.35 µm process using a 3.3 V supply voltage, with dual-rail data andsingle-rail control signals using four-phase handshaking.Using 17,085 transistors, the unit handles single-precision (32-bit addition/subtraction, multiplication,division, and remainder using the IEEE 754-1985 Standard for Binary Floating-Point Arithmetic, withrounding and other operations to be handled by separate hardware or software. Division and remainderare done using a restoring subtractive algorithm; multiplication uses an additive algorithm. Exceptionsare noted by flags (and not trap handlers and the output is in single-precision.Previous work on asynchronous floating-point arithmetic units have mostly focused on single operationssuch as division. This is the first work to the authors' knowledge that can perform floating-point addition,multiplication, division, and remainder using a common datapath.

  14. Irradiation Testing of Ultrasonic Transducers

    International Nuclear Information System (INIS)

    Daw, J.; Rempe, J.; Palmer, J.; Tittmann, B.; Reinhardt, B.; Kohse, G.; Ramuhalli, P.; Montgomery, R.; Chien, H.T.; Villard, J.F.

    2013-06-01

    Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of numerous parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of single, small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of existing knowledge of ultrasonic transducer material survivability under irradiation conditions. To address this need, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate promising magnetostrictive and piezoelectric transducer performance in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 10 21 n/cm 2 (E> 0.1 MeV). This test will be an instrumented lead test; and real-time transducer performance data will be collected along with temperature and neutron and gamma flux data. By characterizing magnetostrictive and piezoelectric transducer survivability during irradiation, test results will enable the development of novel radiation tolerant ultrasonic sensors for use in Material and Test Reactors (MTRs). The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers. (authors)

  15. Pulsed ultrasonic stir welding method

    Science.gov (United States)

    Ding, R. Jeffrey (Inventor)

    2013-01-01

    A method of performing ultrasonic stir welding uses a welding head assembly to include a plate and a rod passing through the plate. The rod is rotatable about a longitudinal axis thereof. In the method, the rod is rotated about its longitudinal axis during a welding operation. During the welding operation, a series of on-off ultrasonic pulses are applied to the rod such that they propagate parallel to the rod's longitudinal axis. At least a pulse rate associated with the on-off ultrasonic pulses is controlled.

  16. Fundamentals of ultrasonic phased arrays

    CERN Document Server

    Schmerr, Lester W

    2014-01-01

    This book describes in detail the physical and mathematical foundations of ultrasonic phased array measurements.?The book uses linear systems theory to develop a comprehensive model of the signals and images that can be formed with phased arrays. Engineers working in the field of ultrasonic nondestructive evaluation (NDE) will find in this approach a wealth of information on how to design, optimize and interpret ultrasonic inspections with phased arrays. The fundamentals and models described in the book will also be of significant interest to other fields, including the medical ultrasound and

  17. Augmenting the Energy-Saving Impact of IEEE 802.3az via the Control Plane

    OpenAIRE

    Thaenchaikun , Chakadkit; Jakllari , Gentian; Paillassa , Béatrice

    2015-01-01

    International audience; IEEE 802.3az, the recent standard for Energy Efficient Ethernet, is one of the main contributions of the ICT industry to the global quest for energy efficiency. Energy consumption reduction is accomplished by essentially replacing the continuous IDLE of legacy IEEE 802.3 cards with a Low Power Idle. While this is an important step in the right direction, studies have shown that the energy saving with IEEE 802.3az highly depends on the traffic load and stops for link ut...

  18. Energy Harvesting - Wireless Sensor Networks for Indoors Applications Using IEEE 802.11

    DEFF Research Database (Denmark)

    Fafoutis, Xenofon; Sørensen, Thomas; Madsen, Jan

    2014-01-01

    The paper investigates the feasibility of using IEEE 802.11 in energy harvesting low-power sensing applications. The investigation is based on a prototype carbon dioxide sensor node that is powered by artificial indoors light. The wireless communication module of the sensor node is based on the RTX......4100 module. RTX4100 incorporates a wireless protocol that duty-cycles the radio while being compatible with IEEE 802.11 access points. The presented experiments demonstrate sustainable operation but indicate a trade-off between the benefits of using IEEE 802.11 in energy harvesting applications...

  19. Computer automation of ultrasonic testing. [inspection of ultrasonic welding

    Science.gov (United States)

    Yee, B. G. W.; Kerlin, E. E.; Gardner, A. H.; Dunmyer, D.; Wells, T. G.; Robinson, A. R.; Kunselman, J. S.; Walker, T. C.

    1974-01-01

    Report describes a prototype computer-automated ultrasonic system developed for the inspection of weldments. This system can be operated in three modes: manual, automatic, and computer-controlled. In the computer-controlled mode, the system will automatically acquire, process, analyze, store, and display ultrasonic inspection data in real-time. Flaw size (in cross-section), location (depth), and type (porosity-like or crack-like) can be automatically discerned and displayed. The results and pertinent parameters are recorded.

  20. Apparatus for ultrasonic nebulization

    International Nuclear Information System (INIS)

    Olson, K.W.; Haas, W.J. Jr.; Fassel, V.A.

    1978-01-01

    An improved apparatus is described for ultrasonic nebulization of liquid samples or suspensions in which the piezoelectric transducer is protected from chemical attack and erosion. The transducer is protected by being bonded to the inner surface of a glass plate which forms one end wall of a first hollow body provided with apparatus for circulating a fluid for cooling and stabilizing the transducer. The glass plate, which is one-half wavelength in thickness to provide an acoustically coupled outer nebulizing surface, seals an opening in a second hollow body which encloses an aerosol mixing chamber. The second body includes apparatus for delivering the sample solution to the nebulizing surface, a gas inlet for providing a flow of carrier gas for transporting the aerosol of the nebulized sample and an aerosol outlet

  1. High resolution ultrasonic densitometer

    International Nuclear Information System (INIS)

    Dress, W.B.

    1983-01-01

    The velocity of torsional stress pulses in an ultrasonic waveguide of non-circular cross section is affected by the temperature and density of the surrounding medium. Measurement of the transit times of acoustic echoes from the ends of a sensor section are interpreted as level, density, and temperature of the fluid environment surrounding that section. This paper examines methods of making these measurements to obtain high resolution, temperature-corrected absolute and relative density and level determinations of the fluid. Possible applications include on-line process monitoring, a hand-held density probe for battery charge state indication, and precise inventory control for such diverse fluids as uranium salt solutions in accountability storage and gasoline in service station storage tanks

  2. Performance Analysis of IEEE 802.11e (EDCF) and IEEE 802.11(DCF) WLAN Incorporating Different Physical Layer Standards

    Science.gov (United States)

    Sharma, V.; Singh, H.; Malhotra, J.

    2012-12-01

    Medium access coordination function basically implements the distributed coordination function (DCF) which provides support to best effort services but limited to QoS services. Subsequently, a new standard, namely enhanced distributed channel access (EDCA) is reported. The IEEE 802.11e (EDCA) defines MAC procedures to support QoS requirements which specifies distributed contention based access scheme to access the shared wireless media. This paper evaluates the performance of EDCA based IEEE 802.11 WLAN for various access categories (ACs) using OPNET™ Modeller 14.5. Further, the computed results are compared with DCF protocols in terms of QoS parameters. Furthermore, the simulative observation is reported at data rate of 54 Mbps using different physical layer protocols such as IEEE 802.11a/b/g to stumble on the best one to be implemented with EDCF to achieve improved QoS.

  3. Analysis of Adaptive Control Scheme in IEEE 802.11 and IEEE 802.11e Wireless LANs

    Science.gov (United States)

    Lee, Bih-Hwang; Lai, Hui-Cheng

    In order to achieve the prioritized quality of service (QoS) guarantee, the IEEE 802.11e EDCAF (the enhanced distributed channel access function) provides the distinguished services by configuring the different QoS parameters to different access categories (ACs). An admission control scheme is needed to maximize the utilization of wireless channel. Most of papers study throughput improvement by solving the complicated multidimensional Markov-chain model. In this paper, we introduce a back-off model to study the transmission probability of the different arbitration interframe space number (AIFSN) and the minimum contention window size (CWmin). We propose an adaptive control scheme (ACS) to dynamically update AIFSN and CWmin based on the periodical monitoring of current channel status and QoS requirements to achieve the specific service differentiation at access points (AP). This paper provides an effective tuning mechanism for improving QoS in WLAN. Analytical and simulation results show that the proposed scheme outperforms the basic EDCAF in terms of throughput and service differentiation especially at high collision rate.

  4. Ultrasonic imaging in concrete

    International Nuclear Information System (INIS)

    Ribay, G.; Paris, O.; Rambach, J.M.

    2009-01-01

    The third and final protection barrier confining nuclear reactors is usually a concrete containment structure. Monitoring the structural integrity of these barriers is critical in ensuring the safety of nuclear power plants. The Institute for Radiological Protection and Nuclear Safety (IRSN) in France in collaboration with the French Atomic commission (CEA/LIST) has developed an ultrasonic phased-array technique capable of inspecting thick concrete walls. The non-destructive method is dedicated to detect cracks and bulk defects. Given the thickness of the structure (1.2 m) undergoing inspection and the heterogeneity of the concrete, the optimal frequency lies in the 50-300 kHz range. At these frequencies, the ultrasonic beam profiles are widespread (non-directive) with poor signal-to-noise ratio. Previous studies have shown the potential of using phased-array techniques (i.e., beam focusing and beam steering) in order to improve detection resolution and sizing accuracy. In this paper we present experimental studies performed with array up to 16 transducers working at 200 kHz. Experiments are carried out on representative concrete blocks containing artificial defects. One is a reinforced mock-up representative of the first reinforcing mesh of wall containment. Experimental results show that in spite of the reinforcement, artificial defects deep as half a meter can be detected. Reconstructed images resulting from phased array acquisitions on an artificial crack embedded in a concrete block are also presented and discussed. The presented method allows detecting oriented defects in concrete with improved signal to noise ratio and sensibility. A simulation model of the interaction of ultrasound with a heterogeneous medium like concrete is briefly commented. (authors)

  5. Case studies in ultrasonic testing

    International Nuclear Information System (INIS)

    Prasad, V.; Satheesh, C.; Varde, P.V.

    2015-01-01

    Ultrasonic testing is widely used Non Destructive Testing (NDT) method and forms the essential part of In-service inspection programme of nuclear reactors. Main application of ultrasonic testing is for volumetric scanning of weld joints followed by thickness gauging of pipelines and pressure vessels. Research reactor Dhruva has completed the first In Service Inspection programme in which about 325 weld joints have been volumetrically scanned, in addition to thickness gauging of 300 meters of pipe lines of various sizes and about 24 nos of pressure vessels. Ultrasonic testing is also used for level measurements, distance measurements and cleaning and decontamination of tools. Two case studies are brought out in this paper in which ultrasonic testing is used successfully for identification of butterfly valve opening status and extent of choking in pipe lines in Dhruva reactor systems

  6. Ultrasonic Technology in Duress Alarms.

    Science.gov (United States)

    Lee, Martha A.

    2000-01-01

    Provides the pros and cons of the most commonly used technologies in personal duress alarm systems in the school environment. Discussed are radio frequency devices, infrared systems, and ultrasonic technology. (GR)

  7. Ultrasonic extensometer measures bolt preload

    Science.gov (United States)

    Daniels, C. M., Jr.

    1978-01-01

    Extensometer using ultrasonic pulse reflections to measure elongations in tightened belts and studs is much more accurate than conventional torque wrenches in application of specified preload to bolts and other threaded fasteners.

  8. IEEE 1588 Time Synchronization Board in MTCA.4 Form Factor

    Science.gov (United States)

    Jabłoński, G.; Makowski, D.; Mielczarek, A.; Orlikowski, M.; Perek, P.; Napieralski, A.; Makijarvi, P.; Simrock, S.

    2015-06-01

    Distributed data acquisition and control systems in large-scale scientific experiments, like e.g. ITER, require time synchronization with nanosecond precision. A protocol commonly used for that purpose is the Precise Timing Protocol (PTP), also known as IEEE 1588 standard. It uses the standard Ethernet signalling and protocols and allows obtaining timing accuracy of the order of tens of nanoseconds. The MTCA.4 is gradually becoming the platform of choice for building such systems. Currently there is no commercially available implementation of the PTP receiver on that platform. In this paper, we present a module in the MTCA.4 form factor supporting this standard. The module may be used as a timing receiver providing reference clocks in an MTCA.4 chassis, generating a Pulse Per Second (PPS) signal and allowing generation of triggers and timestamping of events on 8 configurable backplane lines and two front panel connectors. The module is based on the Xilinx Spartan 6 FPGA and thermally stabilized Voltage Controlled Oscillator controlled by the digital-to-analog converter. The board supports standalone operation, without the support from the host operating system, as the entire control algorithm is run on a Microblaze CPU implemented in the FPGA. The software support for the card includes the low-level API in the form of Linux driver, user-mode library, high-level API: ITER Nominal Device Support and EPICS IOC. The device has been tested in the ITER timing distribution network (TCN) with three cascaded PTP-enabled Hirschmann switches and a GPS reference clock source. An RMS synchronization accuracy, measured by direct comparison of the PPS signals, better than 20 ns has been obtained.

  9. 2011 IEEE Visualization Contest Winner: Visualizing Unsteady Vortical Behavior of a Centrifugal Pump

    KAUST Repository

    Otto, Mathias; Kuhn, Alexander; Engelke, Wito; Theisel, Holger

    2012-01-01

    In the 2011 IEEE Visualization Contest, the dataset represented a high-resolution simulation of a centrifugal pump operating below optimal speed. The goal was to find suitable visualization techniques to identify regions of rotating stall

  10. Harmonization of IEEE323 and IEC60780 standards For Environmental Qualificaiton of Electric Equipment

    International Nuclear Information System (INIS)

    Kim, Jong Seog

    2009-01-01

    IEEE323 standard has been widely used for the qualification of electric equipment in Asian pacific area while IEC6070 has been mostly used in European area. Since each plant use different standard for environmental qualification, manufacturer has to perform the qualification test twice in accordance with each standard. Problem also can be happened in the plant site when they are going to purchase equipment qualified by different qualification standard which are not used in his plant. The need of harmonization of each standard has been raised several years and it is known that some studies are in progress by IEEE committee. KEPRI has a plan of comparing EQ relative standards of IEEE, IEC and RCC in 2009. In this paper, brief comparing result between IEEE323 and IEC60780 and the proper harmonization method is introduced

  11. Defending IEEE 802.11-Based Networks Against Denial Of Service Attacks

    National Research Council Canada - National Science Library

    Tan, Boon

    2003-01-01

    The convenience of IEEE 8O2.11-based wireless access networks has led to widespread deployment in the consumer, industrial and military sectors However, this use is predicated on an implicit assumption of confidentiality...

  12. Corrections to "Connectivity-Based Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs"

    Directory of Open Access Journals (Sweden)

    Choi Woo-Yong

    2010-01-01

    Full Text Available We have found the errors in the throughput formulae presented in our paper "Connectivity-based reliable multicast MAC protocol for IEEE 802.11 wireless LANs". We provide the corrected formulae and numerical results.

  13. Return of IEEE Std 627 and its Value to Equipment Qualification Programs

    International Nuclear Information System (INIS)

    Horvath, D.A.

    2012-01-01

    IEEE Std 627 ''Design Qualification of Safety Systems Equipment Used in Nuclear Power Generating Stations'' was issued to more generically establish qualification requirements in the form of a high level umbrella document. Efforts on this standard began in late 1975 at the request of the IEEE Nuclear Standards Management Board. In 1977 a joint ASME/IEEE agreement established responsibility for qualification and quality assurance standards preparation. ASME accepted responsibility for Quality Assurance and IEEE for qualification. In accordance with that agreement, IEEE completed the generic qualification standard in 1980. This document provided high level approaches, criteria, guidance, and principles for qualification of both electrical and mechanical equipment that at that time appeared in no other industry standard. IEEE Std 627-1980 was later reaffirmed in 1996. In 1986, ASME's Board on Nuclear Codes and Standards directed its Committee on Qualification of Mechanical Equipment (QME) to develop a standard for qualifying mechanical equipment. This task was completed in several parts during the time frame from 1992 to 1994. Partly in response to this activity, IEEE Std 627 was withdrawn in 2002. Later although withdrawn, it was found that IEEE Std 627 was continuing to be used and referenced by many entities both in the US and other countries including in ASME's QME-1-2002 ''Qualification of Active Mechanical Equipment Used in Nuclear Power Plants'', US NRC's NUREG-0800 Standard Review Plan Section 3.11, at least one reactor vendor's Design Certification Document (DCD), several international licensing documents, and elsewhere. As a result, in 2007, the IEEE Standards Board authorized Working Group 2.10 of Subcommittee 2 (Qualification) of the Power and Energy Society's Nuclear Power Engineering Committee to resurrect and update IEEE Std 627-1980 (Reaff 1996). The result was the culmination IEEE Std 627 in 2010. This paper will report on the eight improvements made

  14. Defending IEEE 802.11-Based Networks Against Denial Of Service Attacks

    National Research Council Canada - National Science Library

    Tan, Boon

    2003-01-01

    ...) attacks targeting its management and media access protocols Computer simulation models have proven to be effective tools in the study of cause and effect in numerous fields This thesis involved the design and implementation of a IEEE 8O2.11-based simulation model using OMNeT++, to investigate the effects of different types of DoS attacks on a IEEE 8O2.11 network, and the effectiveness of corresponding countermeasures.

  15. Homeland Security Affairs Journal, Supplement - 2012: IEEE 2011 Conference on Technology for Homeland Security: Best Papers

    OpenAIRE

    2012-01-01

    Homeland Security Affairs is the peer-reviewed online journal of the Naval Postgraduate School Center for Homeland Defense and Security (CHDS), providing a forum to propose and debate strategies, policies, and organizational arrangements to strengthen U.S. homeland security. The instructors, participants, alumni, and partners of CHDS represent the leading subject matter experts and practitioners in the field of homeland security. IEEE Supplement 2012. Supplement: IEEE 2011 Conference on Te...

  16. Performance of the IEEE 802.3 EPON registration scheme under high load

    Science.gov (United States)

    Bhatia, Swapnil P.; Bartos, Radim

    2004-09-01

    The proposed standard for the IEEE 802.3 Ethernet Passive Optical Network includes a random delayed transmission scheme for registration of new nodes. Although the scheme performs well on low loads, our simulation demonstrates the degraded and undesirable performance of the scheme at higher loads. We propose a simple modification to the current scheme that increases its range of operation and is compatible with the IEEE draft standard. We demonstrate the improvement in performance gained without any significant increase in registration delay.

  17. Isolan - A Fibre Optic Network Conforming To IEEE 802.3 Standards

    Science.gov (United States)

    Roworth, D. A. A.; Howe, N.

    1986-10-01

    The progress of the IEEE 802.3 standard for fibre optic LANs is indicated with reference to both mixed media networks and full fibre networks. For a fibre optic network the most suitable layout is a "snowflake" topology composed of multiport repeaters and active fibre hubs. A range of components is described which enables the realisation of such a topology in conformance with the IEEE 802.3 standard.

  18. Validation of IEEE P1547.1 Interconnection Test Procedures: ASCO 7000 Soft Load Transfer System

    Energy Technology Data Exchange (ETDEWEB)

    Kroposki, B.; Englebretson, S.; Pink, C.; Daley, J.; Siciliano, R.; Hinton, D.

    2003-09-01

    This report presents the preliminary results of testing the ASCO 7000 Soft Load Transfer System according to IEEE P1547.1 procedures. The ASCO system interconnects synchronous generators with the electric power system and provides monitoring and control for the generator and grid connection through extensive protective functions. The purpose of this testing is to evaluate and give feedback on the contents of IEEE Draft Standard P1547.1 Conformance Tests Procedures for Equipment Interconnecting Distributed Resources With Electric Power Systems.

  19. Real-time-service-based Distributed Scheduling Scheme for IEEE 802.16j Networks

    OpenAIRE

    Kuo-Feng Huang; Shih-Jung Wu

    2013-01-01

    Supporting Quality of Service (QoS) guarantees for diverse multimedia services is the primary concern for IEEE802.16j networks. A scheduling scheme that satisfies the QoS requirements has become more important for wireless communications. We proposed an adaptive nontransparent-based distributed scheduling scheme (ANDS) for IEEE 802.16j networks. ANDS comprises three major components: Priority Assignment, Resource Allocation, Preserved Bandwidth Adjustment. Different service-type connections p...

  20. Enhancing MAC performance of DCF protocol for IEEE 802.11 wireless LANs

    Science.gov (United States)

    Choi, Woo-Yong

    2017-01-01

    The DCF (Distributed Coordination Function) is the basic MAC (Medium Access Control) protocol of IEEE 802.11 wireless LANs and compatible with various IEEE 802.11 PHY extensions. The performance of the DCF degrades exponentially as the number of nodes participating in the DCF transmission procedure increases. To deal with this problem, we propose a simple, however efficient modification of the DCF by which the performance of the DCF is greatly enhanced.

  1. Radio Frequency Fingerprinting Techniques Through Preamble Modification in IEEE 802.11B

    Science.gov (United States)

    2014-06-30

    4.2.1 Wald–Wolfowitz Runs Test . . . . . . . . . . . . . . . . . . . . . . 41 4.2.2 Wald–Wolfowitz Application to SXS System . . . . . . . . . . . . 42...Station SXS Signals eXploitation System USB Universal Serial Bus xiv Acronym Definition USRP Universal Software Radio Peripheral WLAN Wireless Local...Electronics Engineers (IEEE) defines standards applicable to the IEEE 802.11 protocol, however the standard does not reach the level of specificity to dictate

  2. TransForm: TransAlta 2000 annual report

    International Nuclear Information System (INIS)

    2001-01-01

    Financial information from TransAlta Corp. was presented along with a review of their operations throughout 2000 and a summary of the how the electric utility is doing in terms of power generation, independent power producers, transmission and energy marketing. The utility has changed from a regulated vertically integrated utility into one of Canada's largest non-regulated electric power generators. The utility sold its retail businesses in Alberta and New Zealand and now focuses on coal and hydro generation, gas generation, high-voltage transmission and energy marketing. The newly constructed Centralia, Washington generation facility was brought on line with 1,340 MW in May 2000, on time and on budget. This was the platform to diversify their generation into the United States. The utility reported a solid financial year with $177.9 million in earnings from continuing operations, an 83 per cent increase from 1999, driven mostly by the results of Centralia and power marketing and trading businesses. A financial loss was suffered when the Wabamum power plant in Alberta was shut down for several months to repair a boiler. The utility made excellent progress toward their goal of 15,000 megawatts by 2005 by starting with the construction of what will be one of Canada's largest cogeneration facilities at Sarnia, Ontario. TransAlta also commissioned a 360 MW cogeneration facility at Poplar Creek at Suncor's Fort McMurray oil sand facility. TransAlta also has an excellent track record in developing power generation projects internationally. refs., tabs., figs

  3. Detailed simulation of ultrasonic inspections

    International Nuclear Information System (INIS)

    Chaplin, K.R.; Douglas, S.R.; Dunford, D.

    1997-01-01

    Simulation of ultrasonic inspection of engineering components have been performed at the Chalk River Laboratories of AECL for over 10 years. The computer model, called EWE for Elastic Wave Equations, solves the Elastic Wave Equations using a novel finite difference scheme. It simulates the propagation of an ultrasonic wave from the transducer to a flaw, the scatter of waves from the flaw, and measurement of signals at a receive transducer. Regions of different materials, water and steel for example, can be simulated. In addition, regions with slightly different material properties from the parent material can be investigated. The two major types of output are displays of the ultrasonic waves inside the component and the corresponding A-scans. EPRI and other organizations have used ultrasonic models for: defining acceptable ultrasonic inspection procedures, designing and evaluating inspection techniques, and for quantifying inspection reliability. The EWE model has been applied to the inspection of large pipes in a nuclear plant, gas pipeline welds and steam generator tubes. Most recent work has dealt with the ultrasonic inspection of pressure tubes in CANDU reactors. Pressure tube inspections can reliably detect and size defects; however, there are improvements that can be made. For example, knowing the sharpness of a flaw-tip is crucial for fitness for service assessments. Computer modelling of the ultrasonic inspection of flaws with different root radius has suggested inspection techniques that provide flaw tip radius information. A preliminary investigation of these methods has been made in the laboratory. The basis for the model will be reviewed at the presentation. Then the results of computer simulations will be displayed on a PC using an interactive program that analyzes simulated A-scans. This software tool gives inspection staff direct access to the results of computer simulations. (author)

  4. Ultrasonic measurements and technologies

    CERN Document Server

    Kočiš, Štefan

    1996-01-01

    An impulse for writing this book has originated from the effort to sum­ marize and publicise the acquired results of a research team at the De­ partment of Automation of the Faculty of Electrical Engineering and In­ formatics, Slovak Technical University in Bratislava. The research team has been involved for a long time with control problems for machine production mechanisms and, in recent (approximately 15) years, its effort was aimed mostly at the control of electrical servosystems of robots. Within this scope, the members of the authors' staff solved the State Re­ search Task Ultrasonic sensing of the position of a robot hand, which was coordinated by the Institute of Technical Cybernetics of the Slovak Academy of Sciences in Bratislava. The problem was solved in a complex way, i.e. from a conceptual de­ sign of the measurement, through the measurement and evaluation sys­ tem, up to connection to the control system of a robot. Compensation of the atmospheric influence on the precision of measurement,...

  5. Ultrasonic-testing method

    International Nuclear Information System (INIS)

    Thome, Paul.

    1973-01-01

    Description is given of a device adapted to the detection, by means of ultrasonic waves, of all the flaws and defects included in workpieces when only one face of the latter is accessible. A beam is directed towards the rear-face of the workpiece (e.g. a plate) on which it is reflected. The image thus reflected is fed into a receiver. The latter is under the control of the displacement of that image; simultaneously a transducer checks the condition of the mirror at the places where the beam is reflected. Whenever a flow or defect comes between, a silent zone is formed. By recording the silent zones with respect to the positions of several emitters, it is possible to locates a flaw and to define the outline thereof. The apparatus comprises several ''emitter-receiver'' groups intersecting over the emitter used in order to check the good conditions of the mirror. The invention can be used for searching and identifying flaws and defects in buildings which have to be of top quality (e.g., cofferdams, nuclear devices, shipbuilding yards, aeronautics) [fr

  6. Ultrasonic monitoring system

    International Nuclear Information System (INIS)

    McLain, R.E.

    1975-01-01

    The ultrasonic monitoring system is used in LMFBR's, BWR's or PWR's. A remotely controlled, movable instrument carrier may be used which contains the piezo-electric transducer and is connected to the main control console by a transmission cable. An excitation pulse coming from a pulse generator is used to excite the transducer with a maximum of energy, independent of the length of the transmission line. Pulse width and pulse amplitude can be set without any direct interference into the transducer. For this purpose, a resistor whose impedance has been matched to that of the transmission line is connected to the input of the transmission line. Moreover, a capacitor for generation of the excitation pulse is coupled with the transmission line by means of a four-layer switching diode and is discharged. For termination of the excitation and the control pulses, respectively, another four-layer switching diode connected parallel to the capacitor quickly discharges the capacitor. The capacitor and the capacitance of the line constitute a voltage divider. In this way it is possible to change the length of the transmission line and, to safeguard the generation of a pulse of the desired amplitude, only vary the capacitance of the capacitor. (DG/RF) [de

  7. Synthesis through Trans-disciplinarity

    DEFF Research Database (Denmark)

    Hansen, Hanne Tine Ring

    2006-01-01

    synthesis is a requirement for creating successful ‘environmentally sustainable' architecture through the application of trans-disciplinarity, which leads to an increased awareness of the differences in decision-making as well as that of communication barriers between the different professions......When looking up the word ‘synthesis' in a dictionary, one comes across the following definition: "The combining of separate elements or substances to form a coherent whole."[1] Based on this definition one could argue that all great architectureis achieved through synthesis in one way or another...

  8. Trans issues in Liz Lochhead's 'Not Changed'

    OpenAIRE

    Kaličanin Milena M.

    2017-01-01

    The paper is divided into four sections. In the first section entitled 'Introducing and Defining Trans (Issues)', the basic terms of transgender, transvestite, and transsexual are defined by relying on Stryker's Transgender History (2008). The second part of the paper, 'Trans Studies: In-Between Feminist and Queer Theory?', places transgender studies into an academic context by referring to the theoretical framework provided by trans theorists Stryker, Stone, and Ranck who unanimously claim t...

  9. Ultrasonic propulsion of kidney stones.

    Science.gov (United States)

    May, Philip C; Bailey, Michael R; Harper, Jonathan D

    2016-05-01

    Ultrasonic propulsion is a novel technique that uses short bursts of focused ultrasonic pulses to reposition stones transcutaneously within the renal collecting system and ureter. The purpose of this review is to discuss the initial testing of effectiveness and safety, directions for refinement of technique and technology, and opinions on clinical application. Preclinical studies with a range of probes, interfaces, and outputs have demonstrated feasibility and consistent safety of ultrasonic propulsion with room for increased outputs and refinement toward specific applications. Ultrasonic propulsion was used painlessly and without adverse events to reposition stones in 14 of 15 human study participants without restrictions on patient size, stone size, or stone location. The initial feasibility study showed applicability in a range of clinically relevant situations, including facilitating passage of residual fragments following ureteroscopy or shock wave lithotripsy, moving a large stone at the ureteropelvic junction with relief of pain, and differentiating large stones from a collection of small fragments. Ultrasonic propulsion shows promise as an office-based system for transcutaneously repositioning kidney stones. Potential applications include facilitating expulsion of residual fragments following ureteroscopy or shock wave lithotripsy, repositioning stones prior to treatment, and repositioning obstructing ureteropelvic junction stones into the kidney to alleviate acute renal colic.

  10. The Danish trans-fatty acids ban

    DEFF Research Database (Denmark)

    Vallgårda, Signild

    2017-01-01

    In 2003 an executive order was issued banning industrially produced trans-fatty acids above a low level in food items in Denmark. To date, only a few other countries have followed Denmark’s example. The way health consequences of trans fats were translated by the different actors enabled the crea......In 2003 an executive order was issued banning industrially produced trans-fatty acids above a low level in food items in Denmark. To date, only a few other countries have followed Denmark’s example. The way health consequences of trans fats were translated by the different actors enabled...

  11. Ultrasonic stir welding process and apparatus

    Science.gov (United States)

    Ding, R. Jeffrey (Inventor)

    2009-01-01

    An ultrasonic stir welding device provides a method and apparatus for elevating the temperature of a work piece utilizing at least one ultrasonic heater. Instead of relying on a rotating shoulder to provide heat to a workpiece an ultrasonic heater is utilized to provide ultrasonic energy to the workpiece. A rotating pin driven by a motor assembly performs the weld on the workpiece. A handheld version can be constructed as well as a fixedly mounted embodiment.

  12. The effects of ultrasonic solidification on aluminum

    OpenAIRE

    Đorđević Slavko 1

    2003-01-01

    The effect of ultrasound on characteristics of solidified aluminum was shown. An ultrasonic head and ultrasonic system for modification was designed and applied to the crystallizing aluminum melt. The ultrasonic generator allows power of 50-500 W, amplitude of oscillations 10-100 um.m and the operating frequency of 25 kHz. Ultrasonic modification was done by ultrasound introduced from above into the melt. Microstructure photographs show decreasing of the grain size more than five times.

  13. The effects of ultrasonic solidification on aluminum

    Directory of Open Access Journals (Sweden)

    Đorđević Slavko 1

    2003-01-01

    Full Text Available The effect of ultrasound on characteristics of solidified aluminum was shown. An ultrasonic head and ultrasonic system for modification was designed and applied to the crystallizing aluminum melt. The ultrasonic generator allows power of 50-500 W, amplitude of oscillations 10-100 um.m and the operating frequency of 25 kHz. Ultrasonic modification was done by ultrasound introduced from above into the melt. Microstructure photographs show decreasing of the grain size more than five times.

  14. 21 CFR 872.4850 - Ultrasonic scaler.

    Science.gov (United States)

    2010-04-01

    ... DEVICES DENTAL DEVICES Surgical Devices § 872.4850 Ultrasonic scaler. (a) Identification. An ultrasonic scaler is a device intended for use during dental cleaning and periodontal (gum) therapy to remove calculus deposits from teeth by application of an ultrasonic vibrating scaler tip to the teeth. (b...

  15. Pitch-catch only ultrasonic fluid densitometer

    Science.gov (United States)

    Greenwood, M.S.; Harris, R.V.

    1999-03-23

    The present invention is an ultrasonic fluid densitometer that uses a material wedge and pitch-catch only ultrasonic transducers for transmitting and receiving ultrasonic signals internally reflected within the material wedge. Density of a fluid is determined by immersing the wedge into the fluid and measuring reflection of ultrasound at the wedge-fluid interface. 6 figs.

  16. Ultrasonic techniques for fluids characterization

    CERN Document Server

    Povey, Malcolm J W

    1997-01-01

    This book is a comprehensive and practical guide to the use of ultrasonic techniques for the characterization of fluids. Focusing on ultrasonic velocimetry, the author covers the basic topics and techniques necessaryfor successful ultrasound measurements on emulsions, dispersions, multiphase media, and viscoelastic/viscoplastic materials. Advanced techniques such as scattering, particle sizing, and automation are also presented. As a handbook for industrial and scientific use, Ultrasonic Techniques for Fluids Characterization is an indispensable guide to chemists and chemical engineers using ultrasound for research or process monitoring in the chemical, food processing, pharmaceutical, cosmetic, biotechnology,and fuels industries. Key Features * Appeals to anyone using ultrasound to study fluids * Provides the first detailed description of the ultrasound profiling technique for dispersions * Describes new techniques for measuring phase transitions and nucleation, such as water/ice and oil/fat * Presents the l...

  17. Ultrasonic inspection development at HEDL

    International Nuclear Information System (INIS)

    Day, C.K.; Mech, S.J.; Michaels, T.E.; Dixon, N.E.

    1978-01-01

    Ultrasonic testing methods and equipment are being developed to support preservice and in-service inspection of selected FFTF welds. A digital computer system is employed in the analysis of both simulated FFTF pipe sections and plate specimens containing fatigue cracks. It is anticipated that test evaluation standards containing fatigue cracks will partially eliminate questions formerly associated with weld test calibration producers by providing natural cracks which follow grain boundaries and stress patterns resembling piping situ conditions. Studies have revealed that commercial transducers may satisfy LMFBR ultrasonic pipe inspection applications: The test system evaluation included transducers and wedge coupling and fluid coupling materials which exhibited acceptable performance at temperatures to 2300C. Results are presented that demonstrate the feasibility of ultrasonic inspection of components immersed in sodium at temperatures to 2600C. (UK)

  18. Ultrasonic wave propagation in powders

    Science.gov (United States)

    Al-Lashi, R. S.; Povey, M. J. W.; Watson, N. J.

    2018-05-01

    Powder clumps (cakes) has a significant effect on the flowability and stability of powders. Powder caking is mainly caused by moisture migration due to wetting and environmental (temperature and humidity) changes. The process of moisture migration caking involves creating liquid bridges between the particles during condensation which subsequently harden to form solid bridges. Therefore, an effective and reliable technique is required to quantitatively and non-invasively monitor caking kinetics and effective stiffness. This paper describes two ultrasonic instruments (ultrasonic velocity pulse and airborne ultrasound systems) that have been used to monitor the caking phenomenon. Also, it discusses the relationship between the ultrasonic velocity and attenuation measurements and tracking caking kinetics and the effective stiffness of powders.

  19. Endoscopic endonasal trans-sphenoid surgery of pituitary adenoma

    Directory of Open Access Journals (Sweden)

    Y R Yadav

    2012-01-01

    Full Text Available Endoscopic endonasal trans-sphenoid surgery (EETS is increasingly used for pituitary lesions. Pre-operative CT and MRI scans and peroperative endoscopic visualization can provide useful anatomical information. EETS is indicated in sellar, suprasellar, intraventricular, retro-infundibular, and invasive tumors. Recurrent and residual lesions, pituitary apoplexy and empty sella syndrome can be managed by EETS. Modern neuronavigation techniques, ultrasonic aspirators, ultrasonic bone curette can add to the safety. The binostril approach provides a wider working area. High definition camera is much superior to three-chip camera. Most of the recent reports favor EETS in terms of safety, quality of life and tumor resection, hospital stay, better endocrinological, and visual outcome as compared to the microscopic technique. Nasal symptoms, blood loss, operating time are less in EETS. Various naso-septal flaps and other techniques of CSF leak repair could help reduce complications. Complications can be further reduced after achieving the learning curve, good understanding of limitations with proper patient selection. Use of neuronavigation, proper post-operative care of endocrine function, establishing pituitary center of excellence and more focused residency and endoscopic fellowship training could improve results. The faster and safe transition from microscopic to EETS can be done by the team concept of neurosurgeon/otolaryngologist, attending hands on cadaveric dissection, practice on models, and observation of live surgeries. Conversion to a microscopic or endoscopic-assisted approach may be required in selected patients. Multi-modality treatment could be required in giant and invasive tumors. EETS appears to be a better surgical option in most pituitary adenoma.

  20. On line ultrasonic integrated backscatter

    International Nuclear Information System (INIS)

    Landini, L.; Picano, E.; Mazzarisi, A.; Santarelli, F.; Benassi, A.; De Pieri, G.

    1988-01-01

    A new equipment for on-line evaluation of index based on two-dimensional integrated backscatter from ultrasonic images is described. The new equipment is fully integrated into a B-mode ultrasonic apparatus which provides a simultaneous display of conventional information together with parameters of tissue characterization. The system has been tested with a backscattering model of microbubbles in polysaccharide solution, characterized by a physiological exponential time decay. An exponential fitting to the experimental data was performed which yielded r=0.95

  1. Ultrasonically assisted drilling of rocks

    Science.gov (United States)

    Mikhailova, N. V.; Onawumi, P. Y.; Roy, A.; Silberschmidt, V. V.

    2018-05-01

    Conventional drilling of rocks can generate significant damage in the drilled material; a material layer is often split off a back surface of a sample during drilling, negatively affecting its strength. To improve finish quality, ultrasonically assisted drilling (UAD) was employed in two rocks - sandstone and marble. Damage areas in both materials were reduced in UAD when compared to conventional drilling. Reductions in a thrust force and a torque reduction were observed only for UAD in marble; ultrasonic assistance in sandstone drilling did not result in improvements in this regard.

  2. Very high temperature ultrasonic thermometer

    International Nuclear Information System (INIS)

    Jorzik, E.

    1983-01-01

    An ultrasonic thermometer comprises an electric pulse transducer head, a pulse transmission line, a notched sensor wire attached to and extending along the axis of said transmission line and a sheath enclosing the transmission line and the sensor wire, a portion of the interior face of the sheath being covered by a stuffing material along at least the length of the notched part of the sensor wire, such that contact between the sensor wire and the stuffing material does not substantially give rise to reflection of an ultrasonic pulse at the point of contact. (author)

  3. FACTS ABOUT TRANS FATTY ACIDS

    Directory of Open Access Journals (Sweden)

    Sedighe Asgary

    2010-12-01

    Full Text Available Introduction Fatty acids constitute the main class of lipids in the human diet, being found in nature mainly as glycerol esters that originate triacylglycerols. In the vegetal and animal kingdoms, fatty acids generally have cis unsaturations. In this form, the hydrogens bound to the double bond carbons are on the same side. In another possible configuration, called trans, the hydrogens are bound to un saturations, carbons on opposing sides. Fatty acids with one or more un saturations in the trans configuration are called trans fatty acids (TFAs.1-4      There are two major sources of TFA, those that come from ruminant animals and those that are industrially produced.      The majority of TFAs are found in partially hydrogenated vegetable oils, which contain 10–40% as TFA.5 Hydrogenation is based on the reaction of unsaturated fatty acids of either vegetable or marine oil in the presence of a catalyst, in general nickel. The objective is to increase the oxidative stability of oils by reduction of the concentration of more unsaturated fatty acids and changing their physical properties, thus extending their application. Hydrogenation depends mainly on oil temperature, hydrogen pressure, stirring speed, reaction time, and the catalyst type and concentration. According to the process conditions, hydrogenation is classified as either partial or total and either selective or nonselective.6 It has been estimated that dietary TFAs from partially hydrogenated oils may be responsible for between 30,000 and 100,000 premature coronary deaths per year in the United States.7      The concentration of TFA in meat and milk from ruminants (i.e., cattle, sheep, goats, etc. contain 3 to 8% of total fat.5 It is hypothesized that ruminant TFAs, or certain TFA isomers from ruminant sources, may confer some health benefits; however, since TFA from animal sources accompany saturated fatty acids (SFA, an increase in a single ruminant TFA in the diet is not

  4. IEEE 1547 and 2030 Standards for Distributed Energy Resources Interconnection and Interoperability with the Electricity Grid

    Energy Technology Data Exchange (ETDEWEB)

    Basso, T.

    2014-12-01

    Public-private partnerships have been a mainstay of the U.S. Department of Energy and the National Renewable Energy Laboratory (DOE/NREL) approach to research and development. These partnerships also include technology development that enables grid modernization and distributed energy resources (DER) advancement, especially renewable energy systems integration with the grid. Through DOE/NREL and industry support of Institute of Electrical and Electronics Engineers (IEEE) standards development, the IEEE 1547 series of standards has helped shape the way utilities and other businesses have worked together to realize increasing amounts of DER interconnected with the distribution grid. And more recently, the IEEE 2030 series of standards is helping to further realize greater implementation of communications and information technologies that provide interoperability solutions for enhanced integration of DER and loads with the grid. For these standards development partnerships, for approximately $1 of federal funding, industry partnering has contributed $5. In this report, the status update is presented for the American National Standards IEEE 1547 and IEEE 2030 series of standards. A short synopsis of the history of the 1547 standards is first presented, then the current status and future direction of the ongoing standards development activities are discussed.

  5. Trans Ova Genetics, L.C.

    Science.gov (United States)

    The EPA is providing notice of a proposed Administrative Penalty Assessment against Trans Ova Genetics, L.C., a business located at 2938 380th Street Sioux Center, IA 51250, for alleged violations at the Trans Ova Genetics, L.C.’s facility located in 12425

  6. Unscripting Curriculum: Toward a Critical Trans Pedagogy

    Science.gov (United States)

    Keenan, Harper Benjamin

    2017-01-01

    In this essay, Harper B. Keenan draws on his own experience as a white queer and trans educator to consider the meaning of a critical trans pedagogy. Amid dissonant narratives of equal rights and subjection, he explores how his classroom teaching is shaped by his own experience of gender conditioning as well as by the contemporary political…

  7. TransAlta: More than a utility

    International Nuclear Information System (INIS)

    Mikalson, D.A.

    1991-01-01

    TransAlta Utilities Corporation is Canada's largest privately owned utility and is also a major coal mining company. In 1989, TransAlta produced 20.9% of all coal mined in Canada. A brief history of TransAlta is presented along with TransAlta's present coal operations and plans for the next three years. An overview is presented of how TransAlta Fuel Supply is organized to utilize contracted mining operation, engineering and environmental services and in-house capabilities. Recent strategic initiatives to improve organizational efficiency and the mining operations are discussed. These range from developing a common departmental vision to modifying major mining equipment. TransAlta's proactive role in clean coal combustion such as low NOx-SOx burner, integrated combined cycle gasification, and other energy research projects is reviewed. A summary is provided of recent participation of TransAlta in environmental management initiatives. Recent successes of TransAlta's unregulated subsidiary in the development of cogeneration facilities and the future of this area of business are discussed. 8 refs., 4 figs

  8. Trans fat consumption and aggression.

    Directory of Open Access Journals (Sweden)

    Beatrice A Golomb

    Full Text Available Dietary trans fatty acids (dTFA are primarily synthetic compounds that have been introduced only recently; little is known about their behavioral effects. dTFA inhibit production of omega-3 fatty acids, which experimentally have been shown to reduce aggression. Potential behavioral effects of dTFA merit investigation. We sought to determine whether dTFA are associated with aggression/irritability. METHODOLGY/PRINICPAL FINDINGS: We capitalized on baseline dietary and behavioral assessments in an existing clinical trial to analyze the relationship of dTFA to aggression. Of 1,018 broadly sampled baseline subjects, the 945 adult men and women who brought a completed dietary survey to their baseline visit are the target of this analysis. Subjects (seen 1999-2004 were not on lipid medications, and were without LDL-cholesterol extremes, diabetes, HIV, cancer or heart disease. Outcomes assessed adverse behaviors with impact on others: Overt Aggression Scale Modified-aggression subscale (primary behavioral endpoint; Life History of Aggression; Conflict Tactics Scale; and self-rated impatience and irritability. The association of dTFA to aggression was analyzed via regression and ordinal logit, unadjusted and adjusted for potential confounders (sex, age, education, alcohol, and smoking. Additional analyses stratified on sex, age, and ethnicity, and examined the prospective association. Greater dTFA were strongly significantly associated with greater aggression, with dTFA more consistently predictive than other assessed aggression predictors. The relationship was upheld with adjustment for confounders, was preserved across sex, age, and ethnicity strata, and held cross-sectionally and prospectively.This study provides the first evidence linking dTFA with behavioral irritability and aggression. While confounding is always a concern in observational studies, factors including strength and consistency of association, biological gradient, temporality, and

  9. IEEE C37.105-1987: IEEE standard for qualifying Class 1E protective relays and auxiliaries for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This standard describes the basic principles, requirements, and methods for qualifying Class 1E protective relays and auxiliaries such as test and control switches, terminal blocks, and indicating lamps for applications in nuclear power generating stations. When properly employed it can be used to demonstrate the design adequacy of such equipment under normal, abnormal, design basis event and post design basis event conditions in accordance with ANSI/IEEE Std 323-1983. When protective relays and auxiliaries are located in areas not subject to harsh environments, environmental qualification is not required. Protective relays and auxiliaries located inside primary containment in a nuclear power generating station present special conditions beyond the scope of this document. The qualification procedure presented is generic in nature. Other methods may be used at the discretion of the qualifier, provided the basic precepts of ANSI/IEEE Std 32301983 are satisfied

  10. IEEE No. 323, IEEE trial-use standard: General guide for qualifying Class I electric equipment for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This document describes the basic requirements for the qualification of Class I electric equipment. This is equipment which is essential to the safe shutdown and isolation of the reactor or whose failure or damage could result in significant release of radioactive material. The purpose of this document is to provide guidance for demonstrating the qualifications of electrical equipment as required in the IEEE Std 279 -- Criteria for Nuclear Power Generating Station Protection Systems, and IEEE Std 308 -- Criteria for Class 1E Electric Systems for Nuclear Power Generating Stations. The qualification methods described may be used in conjunction with the Guides for qualifying specific types of equipment, (see Foreword), for updating qualification following modifications or for qualifying equipment for which no applicable Guide exists

  11. Design of handoff procedures for broadband wireless access IEEE 802.16 based networks

    Directory of Open Access Journals (Sweden)

    V. Rangel–Licea

    2008-01-01

    Full Text Available IEEE 802.16 is a protocol for fixed broad band wire less access that is currently trying to add mobility among mobile users in the standard. However, mobility adds some technical barriers that should be solved first, this is the case of HO "handoff" (change of connection between two base stations "BS" by a mobile user. In this paper, the problem of HO in IEEE 802.16 is approached try ing to maintain the quality of service (QoS of mobile users. A mechanism for changing connection during HO is pre sented. A simulation model based on OPNET MODELER1 was developed to evaluate the performance of the proposed HO mechanism. Finally, this paper demonstrates that it is possible to implement a seam less HO mech a nism over IEEE 802.16 even for users with de manding applications such as voice over IP.

  12. An Extended IEEE 118-Bus Test System With High Renewable Penetration

    Energy Technology Data Exchange (ETDEWEB)

    Pena, Ivonne; Martinez-Anido, Carlo Brancucci; Hodge, Bri-Mathias

    2018-01-01

    This article describes a new publicly available version of the IEEE 118-bus test system, named NREL-118. The database is based on the transmission representation (buses and lines) of the IEEE 118-bus test system, with a reconfigured generation representation using three regions of the US Western Interconnection from the latest Western Electricity Coordination Council (WECC) 2024 Common Case [1]. Time-synchronous hourly load, wind, and solar time series are provided for over one year (8784 hours). The public database presented and described in this manuscript will allow researchers to model a test power system using detailed transmission, generation, load, wind, and solar data. This database includes key additional features that add to the current IEEE 118-bus test model, such as: the inclusion of 10 generation technologies with different heat rate functions, minimum stable levels and ramping rates, GHG emissions rates, regulation and contingency reserves, and hourly time series data for one full year for load, wind and solar generation.

  13. PERFORMANCE STUDY OF DISTRIBUTED COORDINATION FUNCTION OVER IEEE 802.11A PHYSICAL LAYER

    Directory of Open Access Journals (Sweden)

    S. SELVAKENEDDY

    2006-06-01

    Full Text Available IEEE 802.11a is one of the latest standards to be released by the IEEE Project 802 for wireless LANs. It has specified an additional physical layer (PHY to support higher data rates, and is termed as the orthogonal frequency division multiplexing (OFDM. In order to exploit its benefits, one of the medium access control (MAC protocols specified in the IEEE 802.11 specification is called distributed coordination function (DCF. DCF is a carrier sense multiple access with collision avoidance (CSMA/CA scheme with slotted binary exponential backoff. The frames can be transmitted using the basic access scheme or the RTS/CTS scheme in DCF. It was demonstrated previously that the RTS/CTS mechanism works well in most scenarios for the previously specified PHYs. In this work, a simple simulator is developed to verify the scalability of the RTS/CTS mechanism over OFDM PHY, which supports much higher data rates.

  14. IEEE 1451.2 based Smart sensor system using ADuc847

    Science.gov (United States)

    Sreejithlal, A.; Ajith, Jose

    IEEE 1451 standard defines a standard interface for connecting transducers to microprocessor based data acquisition systems, instrumentation systems, control and field networks. Smart transducer interface module (STIM) acts as a unit which provides signal conditioning, digitization and data packet generation functions to the transducers connected to it. This paper describes the implementation of a microcontroller based smart transducer interface module based on IEEE 1451.2 standard. The module, implemented using ADuc847 microcontroller has 2 transducer channels and is programmed using Embedded C language. The Sensor system consists of a Network Controlled Application Processor (NCAP) module which controls the Smart transducer interface module (STIM) over an IEEE1451.2-RS232 bus. The NCAP module is implemented as a software module in C# language. The hardware details, control principles involved and the software implementation for the STIM are described in detail.

  15. The scalable coherent interface, IEEE P1596, status and possible applications to data acquisition and physics

    International Nuclear Information System (INIS)

    Gustavson, D.B.

    1990-01-01

    IEEE P1596, the Scalable Coherent Interface (formerly known as SuperBus) is based on experience gained while developing Fastbus (ANSI/IEEE 960-1986, IEC 935), Futurebus (IEEE P896.x) and other modern 32-bit buses. SCI goals include a minimum bandwidth of 1 GByte/sec per processor in multiprocessor systems with thousands of processors; efficient support of a coherent distributed-cache image of distributed shared memory; support for repeaters which interface to existing or future buses; and support for inexpensive small rings as well as for general switched interconnections like Banyan, Omega, or crossbar networks. This paper presents a summary of current directions, reports the status of the work in progress, and suggests some applications in data acquisition and physics. 7 refs

  16. Application of IEEE 1588 to the real-time control system of accelerator

    International Nuclear Information System (INIS)

    Ma Mingchao; Chen Jianfeng; Shen Liren; Jiang Geyang

    2014-01-01

    Background: Time synchronization is one of the core technology of realizing the real-time control of accelerator under the distributed control system architecture. The ordinary crystal frequency deviation of IEEE 1588 causes low synchronous accuracy, which doesn't meet the needs of high precision synchronization. Purpose: This paper proposes an algorithm to improve the synchronization precision caused by the crystal frequency deviation. Methods: According to the basic principle of IEEE 1588 time synchronization, a dynamic frequency compensation (DFC) algorithm module was designed and a test platform was built to verify the feasibility and practicability of the algorithm. The influence of the synchronous cycle and delay jitter of the switch on the synchronization accuracy were analyzed. Results: Experimental results showed the great precision improvement of synchronization after using DFC algorithm. Conclusion: Low synchronous accuracy caused by the crystal frequency deviation can be improved by using DFC algorithm implemented for precision time protocol (PTP) of IEEE 1588. (authors)

  17. An analytical model for the performance analysis of concurrent transmission in IEEE 802.15.4.

    Science.gov (United States)

    Gezer, Cengiz; Zanella, Alberto; Verdone, Roberto

    2014-03-20

    Interference is a serious cause of performance degradation for IEEE802.15.4 devices. The effect of concurrent transmissions in IEEE 802.15.4 has been generally investigated by means of simulation or experimental activities. In this paper, a mathematical framework for the derivation of chip, symbol and packet error probability of a typical IEEE 802.15.4 receiver in the presence of interference is proposed. Both non-coherent and coherent demodulation schemes are considered by our model under the assumption of the absence of thermal noise. Simulation results are also added to assess the validity of the mathematical framework when the effect of thermal noise cannot be neglected. Numerical results show that the proposed analysis is in agreement with the measurement results on the literature under realistic working conditions.

  18. Throughput and delay analysis of IEEE 802.15.6-based CSMA/CA protocol.

    Science.gov (United States)

    Ullah, Sana; Chen, Min; Kwak, Kyung Sup

    2012-12-01

    The IEEE 802.15.6 is a new communication standard on Wireless Body Area Network (WBAN) that focuses on a variety of medical, Consumer Electronics (CE) and entertainment applications. In this paper, the throughput and delay performance of the IEEE 802.15.6 is presented. Numerical formulas are derived to determine the maximum throughput and minimum delay limits of the IEEE 802.15.6 for an ideal channel with no transmission errors. These limits are derived for different frequency bands and data rates. Our analysis is validated by extensive simulations using a custom C+ + simulator. Based on analytical and simulation results, useful conclusions are derived for network provisioning and packet size optimization for different applications.

  19. Measurement of a 3D Ultrasonic Wavefield Using Pulsed Laser Holographic Microscopy for Ultrasonic Nondestructive Evaluation

    Directory of Open Access Journals (Sweden)

    Xing Wang

    2018-02-01

    Full Text Available In ultrasonic array imaging, 3D ultrasonic wavefields are normally recorded by an ultrasonic piezo array transducer. Its performance is limited by the configuration and size of the array transducer. In this paper, a method based on digital holographic interferometry is proposed to record the 3D ultrasonic wavefields instead of the array transducer, and the measurement system consisting of a pulsed laser, ultrasonic excitation, and synchronization and control circuit is designed. A consecutive sequence of holograms of ultrasonic wavefields are recorded by the system. The interferograms are calculated from the recorded holograms at different time sequence. The amplitudes and phases of the transient ultrasonic wavefields are recovered from the interferograms by phase unwrapping. The consecutive sequence of transient ultrasonic wavefields are stacked together to generate 3D ultrasonic wavefields. Simulation and experiments are carried out to verify the proposed technique, and preliminary results are presented.

  20. Ultrasonic inspection of austenitic welds

    International Nuclear Information System (INIS)

    Baikie, B.L.; Wagg, A.R.; Whittle, M.J.; Yapp, D.

    1976-01-01

    Optical and X-ray metallography combined with ultrasonic testing by compression waves was used for inspection of stainless steel weld metal produced by three different welding techniques. X-ray diffraction showed that each weld possessed a characteristic fibre textured structure which was shown by optical microscopy to be parallel to columnar grain boundaries. Metallographic evidence suggested that the development of fibre texture is due to the mechanism of competitive growth. From observations made as a result of optical metallographic examination the orientation of the fibre axis could be predicted if the weld geometry and welding procedure were known. Ultrasonic velocity and attenuation measurements as a continuous function of grain orientation, made on cylinders machined from weld samples, showed that attenuation was strongly orientation dependent. It was concluded that the sensitivity of ultrasonic inspection to small defects is unlikely to be as high for austenitic welds as for ferritic even when transmission is improved by modifying the welding procedure to improve the ultrasonic transmission. (U.K.)

  1. Atmospheric contamination during ultrasonic scaling

    NARCIS (Netherlands)

    Timmerman, MF; Menso, L; Steinfort, J; van Winkelhoff, AJ; van der Weijden, GA

    Objective: The aim of this study was to determine the microbial atmospheric contamination during initial periodontal treatment using a piezoelectric ultrasonic scaler in combination with either high-volume evacuation (HVE) or conventional dental suction (CDS). Methods: The study included 17

  2. Automated evaluation of ultrasonic indications

    International Nuclear Information System (INIS)

    Hansch, M.K.T.; Stegemann, D.

    1994-01-01

    Future requirements of reliability and reproducibility in quality assurance demand computer evaluation of defect indications. The ultrasonic method with its large field of applications and a high potential for automation provides all preconditions for fully automated inspection. The survey proposes several desirable hardware improvements, data acquisition requirements and software configurations. (orig.) [de

  3. Ultrasonic flowmeters. Progress report II

    International Nuclear Information System (INIS)

    Wittekind, W.D.

    1980-01-01

    This progress report presents results of in-plant testing of the prototype ultrasonic flowmeter and describes modifications to the prototype as a result of these tests. The modified prototype, designated MOD-I, is described in detail including the principle of operation, equipment used and the results of both laboratory and in-plant demonstrations

  4. Calculations for Piezoelectric Ultrasonic Transducers

    DEFF Research Database (Denmark)

    Jensen, Henrik

    1986-01-01

    Analysis of piezoelectric ultrasonic transducers implies a solution of a boundary value problem, for a boay which consists of different materials, including a piezoelectric part. The problem is dynamic at frequencies, where a typical wavelength is somewhat less than the size of the body. Radiation...

  5. An IEEE 802.11 EDCA Model with Support for Analysing Networks with Misbehaving Nodes

    Directory of Open Access Journals (Sweden)

    Szott Szymon

    2010-01-01

    Full Text Available We present a novel model of IEEE 802.11 EDCA with support for analysing networks with misbehaving nodes. In particular, we consider backoff misbehaviour. Firstly, we verify the model by extensive simulation analysis and by comparing it to three other IEEE 802.11 models. The results show that our model behaves satisfactorily and outperforms other widely acknowledged models. Secondly, a comparison with simulation results in several scenarios with misbehaving nodes proves that our model performs correctly for these scenarios. The proposed model can, therefore, be considered as an original contribution to the area of EDCA models and backoff misbehaviour.

  6. Reactive GTS Allocation Protocol for Sporadic Events Using the IEEE 802.15.4

    Directory of Open Access Journals (Sweden)

    Mukhtar Azeem

    2014-01-01

    by the IEEE 802.15.4 standard. The proposed control protocol ensures that a given offline sporadic schedule can be adapted online in a timely manner such that the static periodic schedule has not been disturbed and the IEEE 802.15.4 standard compliance remains intact. The proposed protocol is simulated in OPNET. The simulation results are analyzed and presented in this paper to prove the correctness of the proposed protocol regarding the efficient real-time sporadic event delivery along with the periodic event propagation.

  7. Analysis Of Impact Of Various Parameters On BER Performance For IEEE 802.11b

    Directory of Open Access Journals (Sweden)

    Nilesh B. Kalani

    2015-08-01

    Full Text Available Abstract This paper discusses about IEEE 802.11b simulation model implemented using LabVIEW software and its analyses for impact on bit error rate BER for different parameters as channel type channel number data transmission rate and packet size. Audio file is being transmitted processed and analyzed using the model for various parameters. This paper gives analysis of BER verses ESN0 for various parameter like data rate packet size and communication channel for the IEEE 802.11b simulation model generated using LabVIEW. It is proved that BER can be optimized by tweaking different parameters of wireless communication system.

  8. Spectrum Hole Identification in IEEE 802.22 WRAN using Unsupervised Learning

    OpenAIRE

    V. Balaji; S. Anand; C.R. Hota; G. Raghurama

    2016-01-01

    In this paper we present a Cooperative Spectrum Sensing (CSS) algorithm for Cognitive Radios (CR) based on IEEE 802.22Wireless Regional Area Network (WRAN) standard. The core objective is to improve cooperative sensing efficiency which specifies how fast a decision can be reached in each round of cooperation (iteration) to sense an appropriate number of channels/bands (i.e. 86 channels of 7MHz bandwidth as per IEEE 802.22) within a time constraint (channel sensing time). To meet this objectiv...

  9. Self-Coexistence among IEEE 802.22 Networks: Distributed Allocation of Power and Channel

    OpenAIRE

    Sayef Azad Sakin; Md. Abdur Razzaque; Mohammad Mehedi Hassan; Atif Alamri; Nguyen H. Tran; Giancarlo Fortino

    2017-01-01

    Ensuring self-coexistence among IEEE 802.22 networks is a challenging problem owing to opportunistic access of incumbent-free radio resources by users in co-located networks. In this study, we propose a fully-distributed non-cooperative approach to ensure self-coexistence in downlink channels of IEEE 802.22 networks. We formulate the self-coexistence problem as a mixed-integer non-linear optimization problem for maximizing the network data rate, which is an NP-hard one. This work explores a s...

  10. International Conference on Grey Systems and intelligent Services (IEEE GSIS 2009)

    CERN Document Server

    Liu, Sifeng; Advances in Grey Systems Research

    2010-01-01

    This book contains contributions by some of the leading researchers in the area of grey systems theory and applications. All the papers included in this volume are selected from the contributions physically presented at the 2009 IEEE International Conference on Grey Systems and Intelligent Services, November 11 – 12, 2009, Nanjing, Jiangsu, People’s Republic of China. This event was jointly sponsored by IEEE Systems, Man, and Cybernetics Society, Natural Science Foundation of China, and Grey Systems Society of China. Additionally, Nanjing University of Aeronautics and Astronautics also invested heavily in this event with its direct and indirect financial and administrative supports.

  11. IEEE 802.11e (EDCA analysis in the presence of hidden stations

    Directory of Open Access Journals (Sweden)

    Xijie Liu

    2011-07-01

    Full Text Available The key contribution of this paper is the combined analytical analysis of both saturated and non-saturated throughput of IEEE 802.11e networks in the presence of hidden stations. This approach is an extension to earlier works by other authors which provided Markov chain analysis to the IEEE 802.11 family under various assumptions. Our approach also modifies earlier expressions for the probability that a station transmits a packet in a vulnerable period. The numerical results provide the impact of the access categories on the channel throughput. Various throughput results under different mechanisms are presented.

  12. The Trans-Pacific Partnership

    Directory of Open Access Journals (Sweden)

    Voon Tania

    2016-12-01

    Full Text Available This article provides an overview of the recently concluded Trans-Pacific Partnership Agreement (TPP, a treaty the parties have described as comprehensive and ambitious, yet also representing a balance of competing interests. The article focuses on the TPP’s chapters relating to investment, services, intellectual property and regulatory coherence, each of which provides insight into the motivations that drove the conclusion of the TPP and the negotiating dynamics that determined its final content. In areas such as investment, the TPP takes a more balanced approach than many earlier agreements, providing greater safeguards for the regulatory autonomy of states while still embodying core protections for foreign investors. In relation to intellectual property and services, the TPP goes beyond earlier agreements in several key respects, such as preventing the imposition of local presence requirements for service providers or requiring longer copyright terms than those demanded by other international treaties. The TPP chapter on regulatory coherence is one of the most novel features of the treaty, as regulatory coherence is not frequently included in earlier trade agreements, demonstrating the increased focus of states on addressing regulatory barriers to trade and investment. While all of these elements of the TPP are interesting in their own right, given the number and size of the parties involved in the agreement, they also provide valuable guidance about the direction of other ongoing and future preferential trade agreement negotiations, such as the proposed Transatlantic Trade and Investment Partnership (TTIP and Trade in Services Agreement (TiSA.

  13. The tree identify protocol of IEEE 1394 in uCRL

    NARCIS (Netherlands)

    C. Shankland; M.B. van der Zwaag

    1998-01-01

    textabstractWe specify the tree identify protocol of the IEEE 1394 high performance serial multimedia bus at three different levels of detail using $mu$CRL. We use the cones and foci verification technique of Groote and Springintveld to show that the descriptions are equivalent under branching

  14. A 1-GHz charge pump PLL frequency synthesizer for IEEE 1394b PHY

    DEFF Research Database (Denmark)

    Ji, J.; Liu, H.; Li, Q.

    2012-01-01

    This paper presents an implementation of multi-rate SerDes transceiver for IEEE 1394b applications. Simple and effective pre-emphasis and equalizer circuits are used at transmitter and receiver, respectively. A phase interpolator based clock and data recovery circuit with optimized linearity is a...

  15. Energy-aware path selection metric for IEEE 802.11s wireless mesh networking

    CSIR Research Space (South Africa)

    Mhlanga, MM

    2009-01-01

    Full Text Available The IEEE 802.11s working group has commenced activities, which would lead to the development of a standard for wireless mesh networks (WMNs). The draft of 802.11s introduces a new path selection metric called airtime link metric. However...

  16. Energy-aware path selection metric for IEEE 802.11s wireless mesh networking

    CSIR Research Space (South Africa)

    Mhlanga, MM

    2009-08-01

    Full Text Available The IEEE 802.11s working group has commenced activities, which would lead to the development of a standard for wireless mesh networks (WMNs). The draft of 802.11s introduces a new path selection metric called airtime link metric. However...

  17. IEEE 8023 ethernet, current status and future prospects at the LHC

    CERN Document Server

    Dobinson, Robert W; Haas, S; Martin, B; Le Vine, M J; Saka, F

    2000-01-01

    The status of the IEEE 802.3 standard is reviewed and prospects for the future, including the new 10 Gigabit version of Ethernet, are discussed. The relevance of Ethernet for experiments at the CERN Large Hadron Collider is considered, with emphasis on on-line applications and areas which are technically challenging. 8 Refs.

  18. IEEE 802.3 Ethernet, Current Status and Future Prospects at the LHC

    CERN Document Server

    Dobinson, Robert W; Haas, S W; Martin, B; Le Vine, M J; Saka, F

    2000-01-01

    The status of the IEEE 802.3 standard is reviewed and prospects for the future, including the new 10 Gigabit version of Ethernet, are discussed. The relevance of Ethernet for experiments at the CERN Large Hadron Collider is considered, with emphasis on on-line applications and areas which are technically challenging.

  19. Performance Evaluations for IEEE 802.15.4-based IoT Smart Home Solution

    Directory of Open Access Journals (Sweden)

    Nga Dinh

    2016-09-01

    Full Text Available The Internet of Things (IoT is going to be a market-changing force for a variety of real-time applications such as e-healthcare, home automation, environmental monitoring, and industrial automation. Low power wireless communication protocols offering long lifetime and high reliability such as the IEEE 802.15.4 standard have been a key enabling technology for IoT deployments and are deployed for home automation recently. The issues of the IEEE 802.15.4 networks have moved from theory to real world deployments. The work presented herein intends to demonstrate the use of the IEEE 802.15.4 standard in recent IoT commercial products for smart home applications: the Smart Home Starter Kit. The contributions of the paper are twofold. First, the paper presents how the IEEE 802.15.4 standard is employed in Smart Home Starter Kit. In particular, network topology, network operations, and data transfer mode are investigated. Second, network performance metrics such as end-to-end (E2E delay and frame reception ratio (FRR are evaluated by experiments. In addition, the paper discusses several directions for future improvements of home automation commercial products.

  20. The IEEE-SA patent policy update under the lens of EU competition law

    NARCIS (Netherlands)

    Kanevskaia, Olia; Zingales, Nicolo

    2016-01-01

    In 2015, the Institute of Electrical and Electronics Engineers (IEEE) Standardization Association made some controversial changes to its patent policy. The changes include a recommended method of calculation of FRAND royalty rates, and a request to members holding a standard essential patent (SEP)

  1. 0011-0030.IEEE 754: 64 Bit Double Precision FloatsThis.pdf | 01 ...

    Indian Academy of Sciences (India)

    Home; public; Volumes; reso; 021; 01; 0011-0030.IEEE 754: 64 Bit Double Precision FloatsThis.pdf. 404! error. The page your are looking for can not be found! Please check the link or use the navigation bar at the top. YouTube; Twitter; Facebook; Blog. Academy News. IAS Logo. 29th Mid-year meeting. Posted on 19 ...

  2. Evaluation of the Effects of Hidden Node Problems in IEEE 802.15.7 Uplink Performance.

    Science.gov (United States)

    Ley-Bosch, Carlos; Alonso-González, Itziar; Sánchez-Rodríguez, David; Ramírez-Casañas, Carlos

    2016-02-06

    In the last few years, the increasing use of LEDs in illumination systems has been conducted due to the emergence of Visible Light Communication (VLC) technologies, in which data communication is performed by transmitting through the visible band of the electromagnetic spectrum. In 2011, the Institute of Electrical and Electronics Engineers (IEEE) published the IEEE 802.15.7 standard for Wireless Personal Area Networks based on VLC. Due to limitations in the coverage of the transmitted signal, wireless networks can suffer from the hidden node problems, when there are nodes in the network whose transmissions are not detected by other nodes. This problem can cause an important degradation in communications when they are made by means of the Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) access control method, which is used in IEEE 802.15.7 This research work evaluates the effects of the hidden node problem in the performance of the IEEE 802.15.7 standard We implement a simulator and analyze VLC performance in terms of parameters like end-to-end goodput and message loss rate. As part of this research work, a solution to the hidden node problem is proposed, based on the use of idle patterns defined in the standard. Idle patterns are sent by the network coordinator node to communicate to the other nodes that there is an ongoing transmission. The validity of the proposed solution is demonstrated with simulation results.

  3. Adaptive Radio Resource Allocation in Hierarchical QoS Scheduling for IEEE 802.16 Systems

    DEFF Research Database (Denmark)

    Wang, Hua; Dittmann, Lars

    2007-01-01

    Future mobile communication systems such as IEEE 802.16 are expected to deliver a variety of multimedia services with diverse QoS requirements. To guarantee the QoS provision, appropriate scheduler architecture and scheduling algorithms have to be carefully designed. In this paper, we propose...

  4. Evaluation of H.264/AVC over IEEE 802.11p vehicular networks

    Science.gov (United States)

    Rozas-Ramallal, Ismael; Fernández-Caramés, Tiago M.; Dapena, Adriana; García-Naya, José Antonio

    2013-12-01

    The capacity of vehicular networks to offer non-safety services, like infotainment applications or the exchange of multimedia information between vehicles, have attracted a great deal of attention to the field of Intelligent Transport Systems (ITS). In particular, in this article we focus our attention on IEEE 802.11p which defines enhancements to IEEE 802.11 required to support ITS applications. We present an FPGA-based testbed developed to evaluate H.264/AVC (Advanced Video Coding) video transmission over vehicular networks. The testbed covers some of the most common situations in vehicle-to-vehicle and roadside-to-vehicle communications and it is highly flexible, allowing the performance evaluation of different vehicular standard configurations. We also show several experimental results to illustrate the quality obtained when H.264/AVC encoded video is transmitted over IEEE 802.11p networks. The quality is measured considering two important parameters: the percentage of recovered group of pictures and the frame quality. In order to improve performance, we propose to substitute the convolutional channel encoder used in IEEE 802.11p for a low-density parity-check code encoder. In addition, we suggest a simple strategy to decide the optimum number of iterations needed to decode each packet received.

  5. IEEE Conference Record of 1980 Fourteenth Pulse Power Modulator Symposium, 3-5 June 1980.

    Science.gov (United States)

    1980-01-01

    Capacitor Discharges, Proc IEEE 113, p. able operation on Nova we are examing alter- 1549 (1966). nate switch gas (Ar:N 2 :SF 6 ) and electrode material...VOLTTA-KILOVOLTS PLATE VO LTAM --LOVLTS Figure 8. Constant Current Curve for the X2097U Figure 11. Constant Current Curve for the X2097V at 2000 Volt

  6. Oldest Packet Drop (OPD): a Buffering Mechanism for Beaconing in IEEE 802.11p VANETs

    NARCIS (Netherlands)

    van Eenennaam, Martijn; Hendriks, Luuk; Karagiannis, Georgios; Heijenk, Geert

    2011-01-01

    The IEEE 802.11p MAC technology can be used to provide connectivity for real-time vehicle control known as Cooperative Adaptive Cruise Control. Due to the real-time nature of this system, it is paramount the delay of the received information is as small as possible. This paper researches the Oldest

  7. A Comprehensive Taxonomy and Analysis of IEEE 802.15.4 Attacks

    Directory of Open Access Journals (Sweden)

    Yasmin M. Amin

    2016-01-01

    Full Text Available The IEEE 802.15.4 standard has been established as the dominant enabling technology for Wireless Sensor Networks (WSNs. With the proliferation of security-sensitive applications involving WSNs, WSN security has become a topic of great significance. In comparison with traditional wired and wireless networks, WSNs possess additional vulnerabilities which present opportunities for attackers to launch novel and more complicated attacks against such networks. For this reason, a thorough investigation of attacks against WSNs is required. This paper provides a single unified survey that dissects all IEEE 802.15.4 PHY and MAC layer attacks known to date. While the majority of existing references investigate the motive and behavior of each attack separately, this survey classifies the attacks according to clear metrics within the paper and addresses the interrelationships and differences between the attacks following their classification. The authors’ opinions and comments regarding the placement of the attacks within the defined classifications are also provided. A comparative analysis between the classified attacks is then performed with respect to a set of defined evaluation criteria. The first half of this paper addresses attacks on the IEEE 802.15.4 PHY layer, whereas the second half of the paper addresses IEEE 802.15.4 MAC layer attacks.

  8. Interference Measurements in IEEE 802.11 Communication Links Due to Different Types of Interference Sources

    NARCIS (Netherlands)

    van Bloem, J.W.H.; Schiphorst, Roelof; Kluwer, Taco; Slump, Cornelis H.

    2012-01-01

    The number of wireless devices (smartphones, laptops, sensors) that use the 2.4 GHz ISM band is rapidly increasing. The most common communication system in this band is Wi-Fi (IEEE 802.11b/g/n). For that reason coexistence between Wi-Fi and other systems becomes more and more important. In this

  9. Proceedings of the 1988 IEEE international conference on robotics and automation. Volume 1

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    These proceedings compile the papers presented at the international conference (1988) sponsored by IEEE Council on ''Robotics and Automation''. The subjects discussed were: automation and robots of nuclear power stations; algorithms of multiprocessors; parallel processing and computer architecture; and U.S. DOE research programs on nuclear power plants

  10. Performance Analysis of Non-saturated IEEE 802.11 DCF Networks

    Science.gov (United States)

    Zhai, Linbo; Zhang, Xiaomin; Xie, Gang

    This letter presents a model with queueing theory to analyze the performance of non-saturated IEEE 802.11 DCF networks. We use the closed queueing network model and derive an approximate representation of throughput which can reveal the relationship between the throughput and the total offered load under finite traffic load conditions. The accuracy of the model is verified by extensive simulations.

  11. IEEE 802.11 Wireless LANs: Performance Analysis and Protocol Refinement

    Directory of Open Access Journals (Sweden)

    Chatzimisios P.

    2005-01-01

    Full Text Available The IEEE 802.11 protocol is emerging as a widely used standard and has become the most mature technology for wireless local area networks (WLANs. In this paper, we focus on the tuning of the IEEE 802.11 protocol parameters taking into consideration, in addition to throughput efficiency, performance metrics such as the average packet delay, the probability of a packet being discarded when it reaches the maximum retransmission limit, the average time to drop a packet, and the packet interarrival time. We present an analysis, which has been validated by simulation that is based on a Markov chain model commonly used in the literature. We further study the improvement on these performance metrics by employing suitable protocol parameters according to the specific communication needs of the IEEE 802.11 protocol for both basic access and RTS/CTS access schemes. We show that the use of a higher initial contention window size does not considerably degrade performance in small networks and performs significantly better in any other scenario. Moreover, we conclude that the combination of a lower maximum contention window size and a higher retry limit considerably improves performance. Results indicate that the appropriate adjustment of the protocol parameters enhances performance and improves the services that the IEEE 802.11 protocol provides to various communication applications.

  12. Performance characterization of the IEEE 802.11 signal transmission over a multimode fiber PON

    Science.gov (United States)

    Maksymiuk, L.; Siuzdak, J.

    2014-11-01

    In this paper there are presented measurements concerning performance analysis of the IEEE 802.11 signal distribution over multimode fiber based passive optical network. In the paper there are addressed three main sources of impairments: modal noise, frequency response fluctuation of the multimode fiber and non-linear distortion of the signal in the receiver.

  13. Multitemporal Very High Resolution From Space: Outcome of the 2016 IEEE GRSS Data Fusion Contest

    NARCIS (Netherlands)

    Mou, L.; Zhu, X.; Vakalopoulou, M.; Karantzalos, K.; Paragios, N.; Saux, Le B.; Moser, G.; Tuia, D.

    2017-01-01

    In this paper, the scientific outcomes of the 2016 Data Fusion Contest organized by the Image Analysis and Data Fusion Technical Committee of the IEEE Geoscience and Remote Sensing Society are discussed. The 2016 Contest was an open topic competition based on a multitemporal and multimodal dataset,

  14. Outdoor Long-Range WLANs : A Lesson for IEEE 802.11ah

    NARCIS (Netherlands)

    Aust, Stefan; Venkatesha Prasad, R.; Niemegeers, Ignas G M M

    2015-01-01

    Several service applications have been reported by many who proposed the use of wireless LANs (WLANs) over a wide variety of outdoor deployments. In particular, the upcoming IEEE 802.11ah WLAN protocol will enable a longer transmission range between WLAN access points (APs) and stations (STAs) up to

  15. Incorporating antenna beamswitching technique into drivers for IEEE802.11 WLAN devices

    CSIR Research Space (South Africa)

    Mofolo, M

    2015-11-23

    Full Text Available the beamswitching technique for switched parasitic array (SPA) and electronically steerable parasitic array radiator (ESPAR) antennas in the drivers for IEEE802.11 WLAN devices. The modifications of the open source drivers (ath5k and ath9k) to enable real...

  16. Ultrasonic Linear Motor with Two Independent Vibrations

    Science.gov (United States)

    Muneishi, Takeshi; Tomikawa, Yoshiro

    2004-09-01

    We propose a new structure of an ultrasonic linear motor in order to solve the problems of high-power ultrasonic linear motors that drive the XY-stage for electron beam equipment and to expand the application fields of the motor. We pay special attention to the following three points: (1) the vibration in two directions of the ultrasonic linear motor should not influence mutually each other, (2) the vibration in two directions should be divided into the stage traveling direction and the pressing direction of the ultrasonic linear motor, and (3) the rigidity of the stage traveling direction of the ultrasonic linear motor should be increased. As a result, the supporting method of ultrasonic linear motors is simplified. The efficiency of the motor is improved and temperature rise is reduced. The stage position drift is also improved.

  17. Effect of Ultrasonic Frequency on Lactic Acid Fermentation Promotion by Ultrasonic Irradiation

    Science.gov (United States)

    Shimada, Tadayuki; Ohdaira, Etsuzo; Masuzawa, Nobuyoshi

    2004-05-01

    The authors have been researching the promotion of lactic acid fermentation by ultrasonic irradiation. In the past research, it was proven that ultrasonic irradiation is effective in the process of fermentation, and the production of yoghurt and kefir was promoted. In this study, the effect of the ultrasonic frequency in this fermentation process was examined. In the frequency range of this study, it was found that the action of fermentation promotion was exponentially proportionate to the irradiated ultrasonic frequency.

  18. High-resolution ultrasonic spectroscopy

    Directory of Open Access Journals (Sweden)

    V. Buckin

    2018-03-01

    Full Text Available High-resolution ultrasonic spectroscopy (HR-US is an analytical technique for direct and non-destructive monitoring of molecular and micro-structural transformations in liquids and semi-solid materials. It is based on precision measurements of ultrasonic velocity and attenuation in analysed samples. The application areas of HR-US in research, product development, and quality and process control include analysis of conformational transitions of polymers, ligand binding, molecular self-assembly and aggregation, crystallisation, gelation, characterisation of phase transitions and phase diagrams, and monitoring of chemical and biochemical reactions. The technique does not require optical markers or optical transparency. The HR-US measurements can be performed in small sample volumes (down to droplet size, over broad temperature range, at ambient and elevated pressures, and in various measuring regimes such as automatic temperature ramps, titrations and measurements in flow.

  19. Ultrasonic inspection of austenitic welds

    Energy Technology Data Exchange (ETDEWEB)

    Tomlinson, J R; Wagg, A R; Whittle, M J [N.D.T. Applications Centre, CEGB, Manchester (United Kingdom)

    1980-11-01

    The metallurgical structure of austenitic welds is described and contrasted with that found in ferritic welds. It is shown that this structure imparts a marked elastic anisotropy in the ultrasonic propagation parameters. Measurements of variations in the apparent attenuation of sound and deviations in the beam direction are described. The measurements are interpreted in terms of the measured velocity anisotropy. Two applications of the fundamental work are described. In the first it is shown how, by using short pulse compression wave probes, and with major modification of the welding procedure, a stainless steel fillet weld in an AGR boiler can be inspected. In the second application, alternative designs of a transition butt weld have been compared for ease of ultrasonic inspection. The effects of two different welding processes on such an inspection are described. Finally, the paper examines the prospects for future development of inspection and defect-sizing techniques for austenitic welds. (author)

  20. A versatile trigger and synchronization module with IEEE1588 capabilities and EPICS support

    International Nuclear Information System (INIS)

    Lopez, J.M.; Ruiz, M.; Borrego, J.; Arcas, G. de; Barrera, E.; Vega, J.

    2010-01-01

    Event timing and synchronization are two key aspects to improve in the implementation of distributed data acquisition (dDAQ) systems such as the ones used in fusion experiments. It is also of great importance the integration of dDAQ in control and measurement networks. This paper analyzes the applicability of the IEEE1588 and EPICS standards to solve these problems, and presents a hardware module implementation based in both of them that allow adding these functionalities to any DAQ. The IEEE1588 standard facilitates the integration of event timing and synchronization mechanisms in distributed data acquisition systems based on IEEE 803.3 (Ethernet). An optimal implementation of such system requires the use of network interface devices which include specific hardware resources devoted to the IEE1588 functionalities. Unfortunately, this is not the approach followed in most of the large number of applications available nowadays. Therefore, most solutions are based in software and use standard hardware network interfaces. This paper presents the development of a hardware module (GI2E) with IEEE1588 capabilities which includes USB, RS232, RS485 and CAN interfaces. This permits to integrate any DAQ element that uses these interfaces in dDAQ systems in an efficient and simple way. The module has been developed with Motorola's Coldfire MCF5234 processor and National Semiconductors's PHY DP83640T, providing it with the possibility to implement the PTP protocol of IEEE1588 by hardware, and therefore increasing its performance over other implementations based in software. To facilitate the integration of the dDAQ system in control and measurement networks the module includes a basic Input/Output Controller (IOC) functionality of the Experimental Physics and Industrial Control System (EPICS) architecture. The paper discusses the implementation details of this module and presents its applications in advanced dDAQ applications in the fusion community.

  1. Proposed new ultrasonic test bed

    International Nuclear Information System (INIS)

    Maxfield, B.W.

    1978-01-01

    Within the last four or five years, a great deal of progress has been made both here and in a number of other laboratories in developing techniques that will enable considerably more information to be obtained from the ultrasonic examination of an object. Some of these recent developments relate to information contained within the diffracted beam which does not return along the incident path. An ultrasonic examination based upon an evaluation of diffracted energy must use at least two transducers, one for transmission and the other for reception. Current indications are that even more reliable test results will be achieved using a receiving transducer that can scan a significant portion of the diffracted field including that portion which is back-reflected. In general, this scan can be interpreted most accurately if it follows a path related to the surface shape. If more than one region within the object is to be interrogated, then the transmitting transducer must also be scanned, again along a path related to the surface shape. The large quantity of information obtained as the result of such an examination must be subjected to sophisticated computer analysis in order to be displayed in a meaningful and intelligible manner. Although one motivation for building such an instrument is to explore new ultrasonic test procedures that are evolving from current laboratory research, this is neither the sole motivation nor the only use for this instrument. Such a mechanical and electronic device would permit conventional ultrasonic tests to be performed on parts of complex geometry without the expensive and time-consuming special fixturing that is currently required. May possible test geometries could be explored in practice prior to the construction of a specialized test apparatus. Hence, it would be necessary to design much, if any, flexibility into the special test apparatus

  2. Ultrasonic sizing of fatigue cracks

    International Nuclear Information System (INIS)

    Burns, D.J.

    1983-12-01

    Surface and buried fatigue cracks in steel plates have been sized using immersion probes as transmitters-receivers, angled to produce shear waves in the steel. Sizes have been estimated by identifying the ultrasonic waves diffracted from the crack tip and by measuring the time taken for a signal to travel to and from the crack tip. The effects of compression normal to a fatigue crack and of crack front curvature are discussed. Another diffraction technique, developed by UKAEA, Harwell, is reviewed

  3. Ultrasonic characterization of yogurt fermentation process

    OpenAIRE

    IZBAIM , DRIS; FAIZ , BOUAZZA; MOUDDEN , ALI; MALAININE , MOHAMED; ABOUDAOUD , Idriss

    2012-01-01

    International audience; The objective of this work is to characterize the fermentation of yogurt based on an ultrasonic technique. Conventionally, the acidity of the yogurt is measured by a pH meter to determine the progress of fermentation. However, the pH meter should be cleaned and calibrated for each measurement and, therefore, this method is not practical. In this regard, ultrasonic techniques are fast, non-invasive and inexpensive. The measurement of ultrasonic parameters such as amplit...

  4. Experimental investigation of ultrasonic velocity anisotropy in ...

    Indian Academy of Sciences (India)

    Permanent link: https://www.ias.ac.in/article/fulltext/pram/077/02/0345-0355. Keywords. Magnetic fluids; ultrasonic wave; sound velocity; anisotropy. Abstract. Magnetic field-induced dispersion of ultrasonic velocity in a Mn0.7Zn0.3Fe2O4 fluid (applied magnetic field is perpendicular to the ultrasonic propagation vector) is ...

  5. Automated ultrasonic inspection using PULSDAT

    International Nuclear Information System (INIS)

    Naybour, P.J.

    1992-01-01

    PULSDAT (Portable Ultrasonic Data Acquisition Tool) is a system for recording the data from single probe automated ultrasonic inspections. It is one of a range of instruments and software developed by Nuclear Electric to carry out a wide variety of high quality ultrasonic inspections. These vary from simple semi-automated inspections through to multi-probe, highly automated ones. PULSDAT runs under the control of MIPS software, and collects data which is compatible with the GUIDE data display system. PULSDAT is therefore fully compatible with Nuclear Electric's multi-probe inspection systems and utilises all the reliability and quality assurance of the software. It is a rugged, portable system that can be used in areas of difficult access. The paper discusses the benefits of automated inspection and gives an outline of the main features of PULSDAT. Since April 1990 PULSDAT has been used in several applications within Nuclear Electric and this paper presents two examples: the first is a ferritic set-through nozzle and the second is an austenitic fillet weld. (Author)

  6. Formation of trans fats during food preparation.

    Science.gov (United States)

    Przybylski, Oman; Aladedunye, Felix A

    2012-01-01

    An investigation was completed to determine how typical cooking procedures used in food preparation, such as baking and stir-frying, affect trans fats formation. Canola oil was used as the main fat ingredient. Zucchini cake and gingersnap cookies were baked at 180o C and 200o C, while stir-fried chicken was prepared at 200o C and 275o C. The lipids from the food were extracted following the Folch procedure, and analyzed for trans fatty acids according to ISO official method 15304. Minimal changes were observed in the amount of trans fats during baking. Application of extreme temperatures during baking, which caused carbonization of the outer layer of products, yielded an insignificant increase in the amount of trans isomers. As with baking, stir-frying did not result in significant isomerization of the fatty acids, even when the oil was heated to 275o C and smoking heavily before the food was placed in it. Irrespective of the cooking procedure, linolenic acid was the most prone to isomerization with the highest amount of trans isomers formation. Baking and stir-frying at normal and/or extreme temperatures do not significantly affect the amounts of trans fats. Likewise, heating oil to the smoking point during stir-frying may decrease the amount of polyunsaturated fatty acids because of oxidative degradation.

  7. Recent progress in online ultrasonic process monitoring

    Science.gov (United States)

    Wen, Szu-Sheng L.; Chen, Tzu-Fang; Ramos-Franca, Demartonne; Nguyen, Ky T.; Jen, Cheng-Kuei; Ihara, Ikuo; Derdouri, A.; Garcia-Rejon, Andres

    1998-03-01

    On-line ultrasonic monitoring of polymer co-extrusion and gas-assisted injection molding are presented. During the co- extrusion of high density polyethylene and Santoprene ultrasonic sensors consisting of piezoelectric transducers and clad ultrasonic buffer rods are used to detect the interface between these two polymers and the stability of the extrusion. The same ultrasonic sensor also measures the surface temperature of the extruded polymer. The results indicate that temperature measurements using ultrasound have a faster response time than those obtained by conventional thermocouple. In gas-assisted injection molding the polymer and gas flow front positions are monitored simultaneously. This information may be used to control the plunger movement.

  8. Internal ultrasonic inspection of flexible pipe

    Energy Technology Data Exchange (ETDEWEB)

    Baltzersen, O. (IKU Petroleumsforskning A/S, Trondheim (Norway) Norwegian Inst. of Tech., Trondheim (Norway). Div. of Petroleum Engineering and Applied Geophysics); Waag, T.I. (IKU Petroleumsforskning A/S, Trondheim (Norway))

    1993-10-01

    Methods for internal ultrasonic inspection of flexible pipe have been investigated through experiments with a short sample of Coflexip pipe. Ultrasonic backscatter methods using normal and non-normal incidence have been used for qualitative high contrast ultrasonic imaging of the inner surface of the pipe. Analysis of the internal cross-section has been performed based on the use of a non-contact ultrasonic caliper, and processing procedures which enable calculation of, and compensation for, eccentricity of the tool in the pipe. The methods developed can be used to quantitatively estimate the thickness of the internal carcass, and perform high resolution topographic mapping of the inner surface. (Author)

  9. Under sodium ultrasonic imaging system for PFBR

    International Nuclear Information System (INIS)

    Patankar, V.H.; Lalwani, S.K.; Agashe, A.A.

    2014-01-01

    Under Sodium UltraSonic Scanner (USUSS) has been developed to detect the growth and protrusion of fuel sub-assemblies of PFBR, submerged in liquid sodium by using the ultrasonic imaging technique during reactor shut-down when liquid sodium is at 180 ℃. The imaging is carried out prior to every Fuel handling operation. Electronics Division, BARC has designed and developed an 8-Channel Ultrasonic Imaging System (UIS) which consists of 4 downward viewing and 4 side viewing ultrasonic transducers alongwith pulser-receiver, signal processing electronics hardware and software. An automated mechanical scanner developed by IGCAR houses sodium immersible transducers to image the fuel sub assemblies. The system has been successfully tested with dummy protruding and grown FSAs, submerged under liquid sodium. Such ultrasonic imaging systems are not available to India from international market. The USUSS developed indigenously has all the features available in similar systems developed by other countries. After every imaging campaign, the mechanical scanner containing ultrasonic transducers is stored in the Argon filled storage-pit. Before every campaign of USUSS, it is necessary to check the healthiness of the sodium immersible and contaminated ultrasonic transducers, as the under-sodium scanner is decontaminated once in five years. For this purpose, a novel Non Contact Ultrasonic Inspection System (NCUIS) has been designed and developed by Electronics Division, BARC to check the functionality of the high-temperature and contaminated transducers of USUSS, using air-coupled ultrasonic technique. (author)

  10. Stresses in ultrasonically assisted bone cutting

    International Nuclear Information System (INIS)

    Alam, K; Mitrofanov, A V; Silberschmidt, V V; Baeker, M

    2009-01-01

    Bone cutting is a frequently used procedure in the orthopaedic surgery. Modern cutting techniques, such as ultrasonic assisted drilling, enable surgeons to perform precision operations in facial and spinal surgeries. Advanced understanding of the mechanics of bone cutting assisted by ultrasonic vibration is required to minimise bone fractures and to optimise the technique performance. The paper presents results of finite element simulations on ultrasonic and conventional bone cutting analysing the effects of ultrasonic vibration on cutting forces and stress distribution. The developed model is used to study the effects of cutting and vibration parameters (e.g. amplitude and frequency) on the stress distributions in the cutting region.

  11. IEEE Std 383-1974: IEEE standard for type test of Class IE electric cables, field splices, and connections for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This standard provides direction for establishing type tests which may be used in qualifying Class 1E electric cables, field splices, and other connections for service in nuclear power generating stations. General guidelines for qualifications are given in IEEE Std 323-1974, Standard for Qualifying Class IE Electric Equipment for Nuclear Power Generating Stations. Categories of cables covered are those used for power control and instrumentation services. Though intended primarily to pertain to cable for field installation, this guide may also be used for the qualification of internal wiring of manufactured devices. This guide does not cover cables for service within the reactor vessel

  12. "There's no chasing involved": cis/trans relationships, "tranny chasers," and the future of a sex-positive trans politics.

    Science.gov (United States)

    Tompkins, Avery Brooks

    2014-01-01

    This article adds to a small, but growing, body of work on trans sexualities and partnerships, and provides a much-needed inquiry into the complex and contested politics of desire when we take trans identities, bodies, and sexualities into account. Using digital ethnographic data from YouTube videos along with in-person observational data from LGBTQ and trans conferences in the U.S., Tompkins argues that a sex-positive trans politics cannot emerge in trans and trans-allied communities if the rhetoric of the "tranny chaser" continues to inform discourses of desire and attraction to trans people.

  13. Performance Analysis of the IEEE 802.11p Multichannel MAC Protocol in Vehicular Ad Hoc Networks.

    Science.gov (United States)

    Song, Caixia

    2017-12-12

    Vehicular Ad Hoc Networks (VANETs) employ multichannel to provide a variety of safety and non-safety applications, based on the IEEE 802.11p and IEEE 1609.4 protocols. The safety applications require timely and reliable transmissions, while the non-safety applications require efficient and high throughput. In the IEEE 1609.4 protocol, operating interval is divided into alternating Control Channel (CCH) interval and Service Channel (SCH) interval with an identical length. During the CCH interval, nodes transmit safety-related messages and control messages, and Enhanced Distributed Channel Access (EDCA) mechanism is employed to allow four Access Categories (ACs) within a station with different priorities according to their criticality for the vehicle's safety. During the SCH interval, the non-safety massages are transmitted. An analytical model is proposed in this paper to evaluate performance, reliability and efficiency of the IEEE 802.11p and IEEE 1609.4 protocols. The proposed model improves the existing work by taking serval aspects and the character of multichannel switching into design consideration. Extensive performance evaluations based on analysis and simulation help to validate the accuracy of the proposed model and analyze the capabilities and limitations of the IEEE 802.11p and IEEE 1609.4 protocols, and enhancement suggestions are given.

  14. IEEE Std 381-1977: IEEE standard criteria for type tests of Class 1E modules used in nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This document describes the basic requirements of a type test program with the objective of verifying that a module used as Class 1E equipment in a nuclear power generating station meets or exceeds its design specifications. This document is limited to class 1E modules from and including the sensor through the logic circuitry of the final actuation devices. Except for those that are part of a module, switchgear, cables, connections, motors, valve actuators, station batteries, and penetrations are not included and are covered by other IEEE documents. The purpose of this document is to supplement the procedures and requirements given in IEEE Std 323-1974 [24] for type testing Class 1E modules, thereby providing directions for establishment of a type test program which will obtain the required test data and yield the required documentation of test methods and results. This standard is structured to present to the user the principal performance characteristics and environmental parameters which must be considered in designing a type test program for any give Class 1E module. These modules range from tiny sensors to complete racks or cabinets full of equipment that may be located inside or outside containment. The Class 1E modules are required to perform their function before, during, or after, or all, any design basis event specified for the module. The vast variety of modules covered by this document precludes the listing here of specific requirements for each type test

  15. Effect of Trans, Trans-Farnesol on Pseudogymnoascus destructans and Several Closely Related Species.

    Science.gov (United States)

    Raudabaugh, Daniel B; Miller, Andrew N

    2015-12-01

    Bat white-nose syndrome, caused by the psychrophilic fungus Pseudogymnoascus destructans, has dramatically reduced the populations of many hibernating North American bat species. The search for effective biological control agents targeting P. destructans is of great importance. We report that the sesquiterpene trans, trans-farnesol, which is also a Candida albicans quorum sensing compound, prevented in vitro conidial germination for at least 14 days and inhibited growth of preexisting hyphae of five P. destructans isolates in filtered potato dextrose broth at 10 °C. Depending on the inoculation concentrations, both spore and hyphal inhibition occurred upon exposure to concentrations as low as 15-20 µM trans, trans-farnesol. In contrast, most North American Pseudogymnoascus isolates were more tolerant to the exposure of trans, trans-farnesol. Our results suggest that some Candida isolates may have the potential to inhibit the growth of P. destructans and that the sesquiterpene trans, trans-farnesol has the potential to be utilized as a biological control agent.

  16. Ultrasonic Abrasive Removal Of EDM Recast

    Science.gov (United States)

    Mandel, Johnny L.; Jacobson, Marlowe S.

    1990-01-01

    Ultrasonic abrasive process removes layer of recast material generated during electrical-discharge machining (EDM) of damper pocket on turbine blade. Form-fitted tool vibrated ultrasonically in damper pocket from which material removed. Vibrations activate abrasive in pocket. Amount of material removed controlled precisely.

  17. Defect detection and sizing in ultrasonic imaging

    International Nuclear Information System (INIS)

    Moysan, J.; Benoist, P.; Chapuis, N.; Magnin, I.

    1991-01-01

    This paper introduces imaging processing developed with the SPARTACUS system in the field of ultrasonic testing. The aim of the imaging processing is to detect and to separate defects echoes from background noise. Image segmentation and particularities of ultrasonic images are the base of studied methods. 4 figs.; 6 refs [fr

  18. Reproducibility of the results in ultrasonic testing

    International Nuclear Information System (INIS)

    Chalaye, M.; Launay, J.P.; Thomas, A.

    1980-12-01

    This memorandum reports on the conclusions of the tests carried out in order to evaluate the reproducibility of ultrasonic tests made on welded joints. FRAMATOME have started a study to assess the dispersion of results afforded by the test line and to characterize its behaviour. The tests covered sensors and ultrasonic generators said to be identical to each other (same commercial batch) [fr

  19. Backward ray tracing for ultrasonic imaging

    NARCIS (Netherlands)

    Breeuwer, R.

    1990-01-01

    Focused ultrasonic beams frequently pass one or more media interfaces, strongly affecting the ultrasonic beamshape and focusing. A computer program, based on backward ray tracing was developed to compute the shape of a corrected focusing mirror. This shape is verified with another program; then the

  20. Beat-Frequency/Microsphere Medical Ultrasonic Imaging

    Science.gov (United States)

    Yost, William T.; Cantrell, John H.; Pretlow, Robert A., III

    1995-01-01

    Medical ultrasonic imaging system designed to provide quantitative data on various flows of blood in chambers, blood vessels, muscles, and tissues of heart. Sensitive enough to yield readings on flows of blood in heart even when microspheres used as ultrasonic contrast agents injected far from heart and diluted by circulation of blood elsewhere in body.

  1. Cis-trans photoisomerization of abscisic acid

    International Nuclear Information System (INIS)

    Brabham, D.E.; Biggs, R.H.

    1981-01-01

    An important regulator of numerous physiological processes in higher plants is abscisic acid (ABA), which is photoisomerized from the more biologically active cis isomer to the nearly inactive trans isomer by natural sunlight. It is possible that this photoisomerization is a UV control mechanism in functions regulated by ABA. The quantum yields of both the cis to trans and trans to cis photoisomerizations were measured under various conditions of pH and oxygen concentration at room temperature. The yield for photoisomerization of cis-ABA ranged from 0.25 at pH 3.0 to 0.11 at pH 7.0. Oxygen partially quenched the process. The quantum yield varied only slightly with wavelength. The quantum yield of photolysis of cis-ABA was reported for pH 3.0 as 0.06. This yield also varied slightly with wavelength and was relatively insensitive to oxygen. This relatively high yield explains the loss of potency of ABA during UV irradiation. Phosphorescence of cis- and trans-ABA was observed in methanol at 77 K. Onset of the emission was at 350 nm. The emission spectra were the same for both isomers. From these results a mechanism of UV action on plants based on the photoisomerization of the inactive trans-ABA to the biologically active cis isomer is proposed. (author)

  2. Trans Women Doing Sex in San Francisco.

    Science.gov (United States)

    Williams, Colin J; Weinberg, Martin S; Rosenberger, Joshua G

    2016-10-01

    This research investigates the sexuality of trans women (individuals who were assigned male status at birth who currently identify as women), by focusing on the "bodily techniques" (Crossley, 2006) they use in "doing" sexuality. The "doing sexuality" framework not only is modeled after the "doing gender" approach of West and Zimmerman (1987), but also utilizes the idea of "sexual embodiment" to emphasize the agency of trans women as they conceptualize and organize their sexuality in a socially recognized way. This is often difficult as they confront discrimination from medical and legal professionals as well as intimate partners who may find it difficult to adapt to the trans woman's atypical body and conception of gender. However, with a study group of 25 trans women from San Francisco, we found the study participants to be adept at overcoming such hurdles and developing techniques to "do" their sexuality. At the same time, we found trans women's agency constrained by the erotic habitus (Green, 2008) of the wider society. The interplay between innovation and cultural tradition provides an opportunity to fashion a more general model of "doing" sexuality.

  3. Trans issues in Liz Lochhead's 'Not Changed'

    Directory of Open Access Journals (Sweden)

    Kaličanin Milena M.

    2017-01-01

    Full Text Available The paper is divided into four sections. In the first section entitled 'Introducing and Defining Trans (Issues', the basic terms of transgender, transvestite, and transsexual are defined by relying on Stryker's Transgender History (2008. The second part of the paper, 'Trans Studies: In-Between Feminist and Queer Theory?', places transgender studies into an academic context by referring to the theoretical framework provided by trans theorists Stryker, Stone, and Ranck who unanimously claim that transgender studies should have a place of its own within the academia and that trans theory should solely be written by transsexuals. These ideas are applied in the interpretation of Lochhead's story 'Not Changed' in the third segment of the paper. The critical insights of Butler (Gender Trouble, 1990; Undoing Gender, 2004 are found to be most helpful in the interpretation of Lochhead's story about Michael who has willingly undergone Hormone Replacement Therapy to become transsexual Michele. Finally, in the concluding remarks, Lochhead's story is viewed as a trans woman manifesto, urging both non-transsexual and transsexual persons to embrace new beginnings in their relationship.

  4. Hybrid Polling Method for Direct Link Communication for IEEE 802.11 Wireless LANs

    Directory of Open Access Journals (Sweden)

    Woo-Yong Choi

    2008-10-01

    Full Text Available The direct link communication between STAtions (STAs is one of the techniques to improve the MAC performance of IEEE 802.11 infrastructure networks. For the efficient direct link communication, in the literature, the simultaneous polling method was proposed to allow the multiple direct data communication to be performed simultaneously. However, the efficiency of the simultaneous polling method is affected by the interference condition. To alleviate the problem of the lower polling efficiency with the larger interference range, the hybrid polling method is proposed for the direct link communication between STAs in IEEE 802.11 infrastructure networks. By the proposed polling method, we can integrate the sequential and simultaneous polling methods properly according to the interference condition. Numerical examples are also presented to show the medium access control (MAC performance improvement by the proposed polling method.

  5. 2011 IEEE Visualization Contest Winner: Visualizing Unsteady Vortical Behavior of a Centrifugal Pump

    KAUST Repository

    Otto, Mathias

    2012-09-01

    In the 2011 IEEE Visualization Contest, the dataset represented a high-resolution simulation of a centrifugal pump operating below optimal speed. The goal was to find suitable visualization techniques to identify regions of rotating stall that impede the pump\\'s effectiveness. The winning entry split analysis of the pump into three parts based on the pump\\'s functional behavior. It then applied local and integration-based methods to communicate the unsteady flow behavior in different regions of the dataset. This research formed the basis for a comparison of common vortex extractors and more recent methods. In particular, integration-based methods (separation measures, accumulated scalar fields, particle path lines, and advection textures) are well suited to capture the complex time-dependent flow behavior. This video (http://youtu.be/ oD7QuabY0oU) shows simulations of unsteady flow in a centrifugal pump. © 2012 IEEE.

  6. The Exploration of Network Coding in IEEE 802.15.4 Networks

    Directory of Open Access Journals (Sweden)

    Deze Zeng

    2011-01-01

    communication protocol should be energy efficient. The IEEE 802.15.4 is designed as a standard protocol for low power, low data rate, low complexity, and short range connections in WPANs. The standard supports allocating several numbers of collision-free guarantee time slots (GTSs within a superframe for some time-critical transmissions. Recently, COPE was proposed as a promising network coding architecture to essentially improve the throughput of wireless networks. In this paper, we exploit the network coding technique at coordinators to improve energy efficiency of the WPAN. Some related practical issues, such as GTS allocation and multicast, are also discussed in order to exploit the network coding opportunities efficiently. Since the coding opportunities are mostly exploited, our proposal achieves both higher energy efficiency and throughput performance than the original IEEE 802.15.4.

  7. The IEEE 1355 Standard. Developments, performance and application in high energy physics

    International Nuclear Information System (INIS)

    Haas, S.

    1998-12-01

    The data acquisition systems of the next generation High Energy Physics experiments at the Large Hadron Collider (LHC) at CERN will rely on high-speed point-to-point links and switching networks for their higher level trigger and event building systems. This thesis provides a detailed evaluation of the DS-Link and switch technology, which is based on the IEEE 1355 standard for Heterogeneous Interconnect (HIC). The DS-Link is a bidirectional point-to-point serial interconnect, operating at speeds up to 200 MBaud. The objective of this thesis was to study the performance of the IEEE 1355 link and switch technology and to demonstrate that switching networks using this technology would scale to meet the requirements of the High Energy Physics applications

  8. VARNOST BREZŽIČNIH OMREŽIJ PO STANDARDU IEEE 802.11

    OpenAIRE

    Štumberger, Matej

    2013-01-01

    Diplomska naloga se osredotoča na problem varovanja brezžičnih omrežij, zasnovanih po standardu IEEE 802.11. Opisano je združenje IEEE in njihova specifikacija standardov z oznako 802, prav tako pa so opisani tudi standardi, protokoli in tehnike varovanja in zaščite omrežij, ki delujejo po tej specifikaciji. Predstavljeno je tudi trenutno stanje varnosti brezžičnih omrežij na področju mesta Ptuj, opisani in prikazani pa so tudi različni pristopi za zlorabo brezžičnih omrežij, skupaj s program...

  9. Design Optimization of Cyber-Physical Distributed Systems using IEEE Time-sensitive Networks (TSN)

    DEFF Research Database (Denmark)

    Pop, Paul; Lander Raagaard, Michael; Craciunas, Silviu S.

    2016-01-01

    to the optimization of distributed cyber-physical systems using real-time Ethernet for communication. Then, we formulate two novel optimization problems related to the scheduling and routing of TT and AVB traffic in TSN. Thus, we consider that we know the topology of the network as well as the set of TT and AVB flows......In this paper we are interested in safety-critical real-time applications implemented on distributed architectures supporting the Time-SensitiveNetworking (TSN) standard. The ongoing standardization of TSN is an IEEE effort to bring deterministic real-time capabilities into the IEEE 802.1 Ethernet...... standard supporting safety-critical systems and guaranteed Quality-of-Service. TSN will support Time-Triggered (TT) communication based on schedule tables, Audio-Video-Bridging (AVB) flows with bounded end-to-end latency as well as Best-Effort messages. We first present a survey of research related...

  10. Transient Stability Improvement of IEEE 9 Bus System Using Power World Simulator

    Directory of Open Access Journals (Sweden)

    Kaur Ramandeep

    2016-01-01

    Full Text Available The improvement of transient stability of power system was one of the most challenging research areas in power engineer.The main aim of this paper was transient stability analysis and improvement of IEEE 9 bus system. These studies were computed using POWER WORLD SIMULATOR. The IEEE 9 bus system was modelled in power world simulator and load flow studies were performed to determine pre-fault conditions in the system using Newton-Raphson method. The transient stability analysis was carried out using Runga method during three-phase balanced fault. For the improvement transient stability, the general methods adopted were fast acting exciters, FACT devices and addition of parallel transmission line. These techniques play an important role in improving the transient stability, increasing transmission capacity and damping low frequency oscillations.

  11. Integration of IEEE 1451 and HL7 exchanging information for patients' sensor data.

    Science.gov (United States)

    Kim, Wooshik; Lim, Suyoung; Ahn, Jinsoo; Nah, Jiyoung; Kim, Namhyun

    2010-12-01

    HL7 (Health Level 7) is a standard developed for exchanging incompatible healthcare information generated from programs or devices among heterogenous medical information systems. At present, HL7 is growing as a global standard. However, the HL7 standard does not support effective methods for treating data from various medical sensors, especially from mobile sensors. As ubiquitous systems are growing, HL7 must communicate with various medical transducers. In the area of sensor fields, IEEE 1451 is a group of standards for controlling transducers and for communicating data from/to various transducers. In this paper, we present the possibility of interoperability between the two standards, i.e., HL7 and IEEE 1451. After we present a method to integrate them and show the preliminary results of this approach.

  12. A note on bound constraints handling for the IEEE CEC'05 benchmark function suite.

    Science.gov (United States)

    Liao, Tianjun; Molina, Daniel; de Oca, Marco A Montes; Stützle, Thomas

    2014-01-01

    The benchmark functions and some of the algorithms proposed for the special session on real parameter optimization of the 2005 IEEE Congress on Evolutionary Computation (CEC'05) have played and still play an important role in the assessment of the state of the art in continuous optimization. In this article, we show that if bound constraints are not enforced for the final reported solutions, state-of-the-art algorithms produce infeasible best candidate solutions for the majority of functions of the IEEE CEC'05 benchmark function suite. This occurs even though the optima of the CEC'05 functions are within the specified bounds. This phenomenon has important implications on algorithm comparisons, and therefore on algorithm designs. This article's goal is to draw the attention of the community to the fact that some authors might have drawn wrong conclusions from experiments using the CEC'05 problems.

  13. Qualification of cables to IEEE standards 323-1974 and 383-1974

    International Nuclear Information System (INIS)

    Hosticka, C.; Kingsbury, E.R.; Bruhin, A.C.

    1980-01-01

    Wire and Cable manufacturers generally qualify products for class IE application by envelope type testing to user specifications and environmental conditions recommended by IEEE Standards 323-1974 and 383-1974. The General Electric Wire and Cable Business Department recently completed two such qualification programs. Cable constructions tested were 600V control cables and 600 V, 2kV, and 15kV power cables insulated with flame resistant mineral filled crosslinked polyethylene. The 15kV samples included taped field splices. In the second test program, the steam pressure-temperature profile included a simulated main steam line break. Test specimens were wrapped on grounded mandrels and were electrically loaded throughout the simulated LOCA tests. After completion of environmental testing, samples were subjected to the IEEE 383 simulated post-LOCA test. 6 refs

  14. Qualification of cables to IEEE standards 323-1974 and 383-1974

    International Nuclear Information System (INIS)

    Hosticka, C.; Kingsbury, E.R.; Bruhin, A.C.

    1980-01-01

    Wire and Cable manufacturers generally qualify products for class IE application by envelope type testing to user specifications and environmental conditions recommended by IEEE Standards 323-1974 and 383-1974. The General Electric Wire and Cable Business Department recently completed two such qualification programs. Cable constructions tested were 600V control cables and 600 V, 2KV, and 15KV power cables insulated with flame resistant mineral filled crosslinked polyethylene. The 15KV samples included taped field splices. In the second test program, the steam pressure-temperature profile included a simulated main steam line break. Test specimens were wrapped on grounded mandrels and were electrically loaded throughout the simulated LOCA tests. After completion of environmental testing, samples were subjected to the IEEE 383 simulated post-LOCA test. 6 refs

  15. A Novel IEEE 802.15.4e DSME MAC for Wireless Sensor Networks.

    Science.gov (United States)

    Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

    2017-01-16

    IEEE 802.15.4e standard proposes Deterministic and Synchronous Multichannel Extension (DSME) mode for wireless sensor networks (WSNs) to support industrial, commercial and health care applications. In this paper, a new channel access scheme and beacon scheduling schemes are designed for the IEEE 802.15.4e enabled WSNs in star topology to reduce the network discovery time and energy consumption. In addition, a new dynamic guaranteed retransmission slot allocation scheme is designed for devices with the failure Guaranteed Time Slot (GTS) transmission to reduce the retransmission delay. To evaluate our schemes, analytical models are designed to analyze the performance of WSNs in terms of reliability, delay, throughput and energy consumption. Our schemes are validated with simulation and analytical results and are observed that simulation results well match with the analytical one. The evaluated results of our designed schemes can improve the reliability, throughput, delay, and energy consumptions significantly.

  16. A Fast MAC-Layer Handover for an IEEE 802.16e-Based WMAN

    Science.gov (United States)

    Ray, Sayan K.; Pawlikowski, Krzysztof; Sirisena, Harsha

    We propose a modification of the IEEE 802.16e hard handover (HHO) procedure, which significantly reduces the handover latency constraint of the original HHO procedure in IEEE 802.16e networks. It allows a better handling of the delay-sensitive traffic by avoiding unnecessary time-consuming scanning and synchronization activity as well as simplifies the network re-entry procedure. With the help of the backhaul network, it reduces the number of control messages in the original handover policy, making the handover latency acceptable also for real-time streaming traffic. Preliminary performance evaluation studies show that the modified handover procedure is able to reduce the total handover latency by about 50%.

  17. A network architecture for precision formation flying using the IEEE 802.11 MAC Protocol

    Science.gov (United States)

    Clare, Loren P.; Gao, Jay L.; Jennings, Esther H.; Okino, Clayton

    2005-01-01

    Precision Formation Flying missions involve the tracking and maintenance of spacecraft in a desired geometric formation. The strong coupling of spacecraft in formation flying control requires inter-spacecraft communication to exchange information. In this paper, we present a network architecture that supports PFF control, from the initial random deployment phase to the final formation. We show that a suitable MAC layer for the application protocol is IEEE's 802.11 MAC protocol. IEEE 802.11 MAC has two modes of operations: DCF and PCF. We show that DCF is suitable for the initial deployment phase while switching to PCF when the spacecraft are in formation improves jitter and throughput. We also consider the effect of routing on protocol performance and suggest when it is profitable to turn off route discovery to achieve better network performance.

  18. Capacity Evaluation for IEEE 802.16e Mobile WiMAX

    Directory of Open Access Journals (Sweden)

    Chakchai So-In

    2010-01-01

    Full Text Available We present a simple analytical method for capacity evaluation of IEEE 802.16e Mobile WiMAX networks. Various overheads that impact the capacity are explained and methods to reduce these overheads are also presented. The advantage of a simple model is that the effect of each decision and sensitivity to various parameters can be seen easily. We illustrate the model by estimating the capacity for three sample applications—Mobile TV, VoIP, and data. The analysis process helps explain various features of IEEE 802.16e Mobile WiMAX. It is shown that proper use of overhead reducing mechanisms and proper scheduling can make an order of magnitude difference in performance. This capacity evaluation method can also be used for validation of simulation models.

  19. The Dynamic Performance of Flexural Ultrasonic Transducers

    Directory of Open Access Journals (Sweden)

    Andrew Feeney

    2018-01-01

    Full Text Available Flexural ultrasonic transducers are principally used as proximity sensors and for industrial metrology. Their operation relies on a piezoelectric ceramic to generate a flexing of a metallic membrane, which delivers the ultrasound signal. The performance of flexural ultrasonic transducers has been largely limited to excitation through a short voltage burst signal at a designated mechanical resonance frequency. However, a steady-state amplitude response is not generated instantaneously in a flexural ultrasonic transducer from a drive excitation signal, and differences in the drive characteristics between transmitting and receiving transducers can affect the measured response. This research investigates the dynamic performance of flexural ultrasonic transducers using acoustic microphone measurements and laser Doppler vibrometry, supported by a detailed mechanical analog model, in a process which has not before been applied to the flexural ultrasonic transducer. These techniques are employed to gain insights into the physics of their vibration behaviour, vital for the optimisation of industrial ultrasound systems.

  20. Contributions to the 14th IEEE/NPSS Symposium on fusion engineering

    International Nuclear Information System (INIS)

    Navarro, A.P.; Almoguera, L.; Alonso Gozalo, J.; Alonso Candenas, J.; Blaumoser, M.

    1992-01-01

    Three communications about the TJ-II device, under construction at CIEMAT with preferential support from EURATOM, were presented to the 14th IEEE/NPSS Symposium on Fusion Engineering and are collected in this report. The first one describes in detail the device and its present status of design and construction. The remaining two deal with the two most critical components of the project: the vacuum vessel and the central hard conductor. (author) 16 fig. 16 ref

  1. Utilizing reliability concepts in the development of IEEE recommended good practices for nuclear plant maintenance

    International Nuclear Information System (INIS)

    Gradin, L.P.

    1986-01-01

    This paper presents information describing the concern for nuclear power plant electrical equipment maintenance and the IEEE Nuclear Power Engineering Committee's method to address that concern. That method includes the creation of Working Group 3.3, ''Maintenance Good Practices'' which is developing specific maintenance good practice documents, supporting technical information exchange, and providing a vehicle to promote practices which can reduce cost and enhance plant safety. The foundation for that effort is the utilization of Reliability concepts

  2. Practical support for Lean Six Sigma software process definition using IEEE software engineering standards

    CERN Document Server

    Land, Susan K; Walz, John W

    2012-01-01

    Practical Support for Lean Six Sigma Software Process Definition: Using IEEE Software Engineering Standards addresses the task of meeting the specific documentation requirements in support of Lean Six Sigma. This book provides a set of templates supporting the documentation required for basic software project control and management and covers the integration of these templates for their entire product development life cycle. Find detailed documentation guidance in the form of organizational policy descriptions, integrated set of deployable document templates, artifacts required in suppo

  3. [Mobile Health: IEEE Standard for Wearable Cuffless Blood Pressure Measuring Devices].

    Science.gov (United States)

    Zhou, Xia; Wu, Wenli; Bao, Shudi

    2015-07-01

    IEEE Std 1708-2014 breaks through the traditional standards of cuff based blood pressure measuring devices and establishes a normative definition of wearable cuffless blood pressure measuring devices and the objective performance evaluation of this kind of devices. This study firstly introduces the background of the new standard. Then, the standard details will be described, and the impact of cuffless blood pressure measuring devices with the new standard on manufacturers and end users will be addressed.

  4. IEEE guide for general principles of reliability analysis of nuclear power generating station protection systems

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    Presented is the Institute of Electrical and Electronics Engineers, Inc. (IEEE) guide for general principles of reliability analysis of nuclear power generating station protection systems. The document has been prepared to provide the basic principles needed to conduct a reliability analysis of protection systems. Included is information on qualitative and quantitative analysis, guides for failure data acquisition and use, and guide for establishment of intervals

  5. IEEE standard for qualifying class IE equipment for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1974-01-01

    The Institute of Electrical and Electrical Engineers, Inc. (IEEE) standards for electrical equipment (Class IE) for nuclear power generating stations are given. The standards are to provide guidance for demonstrating and documenting the adequacy of electric equipment used in all Class IE and interface systems. Representative in containment design basis event conditions for the principal reactor types are included in the appendixes for guidance in enviromental simulation

  6. Plasma Sterilizer with Ultrasonic Cavitation

    International Nuclear Information System (INIS)

    Krasnyj, V.V.; Klosovsky, A.V.; Panasko, T.A.; Shvets, O.M.; Semenova, O.T.; Taran, V.S.; Tereshin, V.I.

    2006-01-01

    A sterilizer consists of ozone generator based on a barrier glow discharge with the flat electrodes covered with dielectric with a high-voltage pulsed power supply of up to 250 W (1). The sterilization camera is equipped with ultrasonic source with the power of 100 W. The experiments on the inactivation of bacteria of the Bacillus Cereus type were carried out in the distilled water saturated by ozone. Ozone concentration in the aqueous solution was 6 mg/liter with ozone concentration at the output of ozone generator 30 mg/liter. The complete inactivation of spores took 15 min

  7. An improved IEEE 802.11 protocol for reliable data transmission in power distribution fault diagnosis

    Energy Technology Data Exchange (ETDEWEB)

    Campoccia, F.; Di Silvestre, M.L.; Sanseverino, E.R.; Zizzo, G. [Palermo Univ., Palermo (Italy)

    2010-10-15

    In power systems, on-line transmission between local units and the central unit can be done by means of power line communications or wireless technology. During an electrical fault, the reliability of the distribution system depends on the security of the timely protective and restorative actions on the network. This paper focused on the WiFi system because of its economy and ease of installation. However, WiFi systems are typically managed by the IEEE 802.11 protocol, which is not reliable in terms of security in data communication. In WiFi networks, data is divided into packets and sent in succession to reduce errors within the radio channel. The IEEE 802.11 protocol has high probability for loss of packets or delay in their transmission. In order to ensure the reliability of data transmission times between two terminal units connected by WiFi stations, a new protocol was derived by modifying the IEEE 802.11. The improvements of the new protocol were highlighted and its capability for the diagnostic service was verified. The modified protocol eliminates the danger of collisions between packets and optimizes the transmission time for sending information. 6 refs., 7 tabs., 8 figs.

  8. FPGA implementation cost and performance evaluation of IEEE 802.11 protocol encryption security schemes

    Science.gov (United States)

    Sklavos, N.; Selimis, G.; Koufopavlou, O.

    2005-01-01

    The explosive growth of internet and consumer demand for mobility has fuelled the exponential growth of wireless communications and networks. Mobile users want access to services and information, from both internet and personal devices, from a range of locations without the use of a cable medium. IEEE 802.11 is one of the most widely used wireless standards of our days. The amount of access and mobility into wireless networks requires a security infrastructure that protects communication within that network. The security of this protocol is based on the wired equivalent privacy (WEP) scheme. Currently, all the IEEE 802.11 market products support WEP. But recently, the 802.11i working group introduced the advanced encryption standard (AES), as the security scheme for the future IEEE 802.11 applications. In this paper, the hardware integrations of WEP and AES are studied. A field programmable gate array (FPGA) device has been used as the hardware implementation platform, for a fair comparison between the two security schemes. Measurements for the FPGA implementation cost, operating frequency, power consumption and performance are given.

  9. Performance Evaluation of Beacon-Enabled Mode for IEEE 802.15.4 Wireless Sensor Network

    Directory of Open Access Journals (Sweden)

    M. Udin Harun Al Rasyid

    2013-12-01

    Full Text Available IEEE 802.15.5 standard support structure of star and peer-to-peer network formation. Strating from these, the cluster tree network can be built as a special case of peer-to-peer network to increse coverage area. In this paper, we provide an performance evaluation of beacon- enabled mode for IEEE 802.15.4 wireless sensor network on star and cluster topology in order to get the maximum result to apply the appropriate topology model as needed. We conduct analysis on each topology model by using the numbers of nodes from 10 nodes to 100 nodes to analyze throughput, delay, energy consumption, and probability success packet by using NS2 simulator. The simulation results show that the throughput and the probability of success packet of cluster topology are higher than that of star topology, and the energy consumption of cluster topology is lesser than that of star topology. However, cluster topology increases the delay more than star topology. Keywords: IEEE 802.15.4, wireless sensor network, beacon-enabled mode, topology, csma/ca

  10. Interoperability in digital electrocardiography: harmonization of ISO/IEEE x73-PHD and SCP-ECG.

    Science.gov (United States)

    Trigo, Jesús D; Chiarugi, Franco; Alesanco, Alvaro; Martínez-Espronceda, Miguel; Serrano, Luis; Chronaki, Catherine E; Escayola, Javier; Martínez, Ignacio; García, José

    2010-11-01

    The ISO/IEEE 11073 (x73) family of standards is a reference frame for medical device interoperability. A draft for an ECG device specialization (ISO/IEEE 11073-10406-d02) has already been presented to the Personal Health Device (PHD) Working Group, and the Standard Communications Protocol for Computer-Assisted ElectroCardioGraphy (SCP-ECG) Standard for short-term diagnostic ECGs (EN1064:2005+A1:2007) has recently been approved as part of the x73 family (ISO 11073-91064:2009). These factors suggest the coordinated use of these two standards in foreseeable telecardiology environments, and hence the need to harmonize them. Such harmonization is the subject of this paper. Thus, a mapping of the mandatory attributes defined in the second draft of the ISO/IEEE 11073-10406-d02 and the minimum SCP-ECG fields is presented, and various other capabilities of the SCP-ECG Standard (such as the messaging part) are also analyzed from an x73-PHD point of view. As a result, this paper addresses and analyzes the implications of some inconsistencies in the coordinated use of these two standards. Finally, a proof-of-concept implementation of the draft x73-PHD ECG device specialization is presented, along with the conversion from x73-PHD to SCP-ECG. This paper, therefore, provides recommendations for future implementations of telecardiology systems that are compliant with both x73-PHD and SCP-ECG.

  11. IEEE recommended practices for seismic qualification of Class 1E equipment for nuclear power generating stations

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    The IEEE has developed this document to provide direction for developing programs to seismically qualify Class 1E equipment for nuclear power generating stations. It supplements IEEE Std 323-1974, IEEE Standard for Qualifying Class 1E Equipment for Nuclear Power Generating Stations, which describes the basic requirements for equipment qualification. The Class 1E equipment to be qualified by produres or standards established by this document are of many forms, characteristics, and materials; therefore, the document presents many acceptable methods with the intent of permitting the user to make a judicious selection from among the various options. In making such a selection, the user should choose those that best meet a particular equipment's requirements. Further, in using this document as a specification for the purchase of equipment, the many options should also be recognized and the document invoked accordingly. It is recommended that the need for specific standards for the seismic qualifiction of particular kinds of equipment be evaluated by those responsible for such documents and that consideration be given to the application of particular methods from these documents which are most suitable

  12. IEEE P1596, a scalable coherent interface for GigaByte/sec multiprocessor applications

    International Nuclear Information System (INIS)

    Gustavson, D.B.

    1988-11-01

    IEEE P1596, the Scalable Coherent Interface (formerly known as SuperBus) is based on experience gained during the development of Fastbus (IEEE 960), Futurebus (IEEE 896.1) and other modern 32-bit buses. SCI goals include a minimum bandwidth of 1 GByte/sec per processor; efficient support of a coherent distributed-cache image of shared memory; and support for segmentation, bus repeaters and general switched interconnections like Banyan, Omega, or full crossbar networks. To achieve these ambitious goals, SCI must sacrifice the immediate handshake characteristic of the present generation of buses in favor of a packet-like split-cycle protocol. Wire-ORs, broadcasts, and even ordinary passive bus structures are to be avoided. However, a lower performance (1 GByte/sec per backplane instead of per processor) implementation using a register insertion ring architecture on a passive ''backplane'' appears to be possible using the same interface as for the more costly switch networks. This paper presents a summary of current directions, and reports the status of the work in progress

  13. Study on Additional Carrier Sensing for IEEE 802.15.4 Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Bih-Hwang Lee

    2010-06-01

    Full Text Available Wireless sensor networks based on the IEEE 802.15.4 standard are able to achieve low-power transmissions in the guise of low-rate and short-distance wireless personal area networks (WPANs. The slotted carrier sense multiple access with collision avoidance (CSMA/CA is used for contention mechanism. Sensor nodes perform a backoff process as soon as the clear channel assessment (CCA detects a busy channel. In doing so they may neglect the implicit information of the failed CCA detection and further cause the redundant sensing. The blind backoff process in the slotted CSMA/CA will cause lower channel utilization. This paper proposes an additional carrier sensing (ACS algorithm based on IEEE 802.15.4 to enhance the carrier sensing mechanism for the original slotted CSMA/CA. An analytical Markov chain model is developed to evaluate the performance of the ACS algorithm. Both analytical and simulation results show that the proposed algorithm performs better than IEEE 802.15.4, which in turn significantly improves throughput, average medium access control (MAC delay and power consumption of CCA detection.

  14. FPGA implementation cost and performance evaluation of IEEE 802.11 protocol encryption security schemes

    International Nuclear Information System (INIS)

    Sklavos, N; Selimis, G; Koufopavlou, O

    2005-01-01

    The explosive growth of internet and consumer demand for mobility has fuelled the exponential growth of wireless communications and networks. Mobile users want access to services and information, from both internet and personal devices, from a range of locations without the use of a cable medium. IEEE 802.11 is one of the most widely used wireless standards of our days. The amount of access and mobility into wireless networks requires a security infrastructure that protects communication within that network. The security of this protocol is based on the wired equivalent privacy (WEP) scheme. Currently, all the IEEE 802.11 market products support WEP. But recently, the 802.11i working group introduced the advanced encryption standard (AES), as the security scheme for the future IEEE 802.11 applications. In this paper, the hardware integrations of WEP and AES are studied. A field programmable gate array (FPGA) device has been used as the hardware implementation platform, for a fair comparison between the two security schemes. Measurements for the FPGA implementation cost, operating frequency, power consumption and performance are given

  15. Strategies for Optimal MAC Parameters Tuning in IEEE 802.15.6 Wearable Wireless Sensor Networks.

    Science.gov (United States)

    Alam, Muhammad Mahtab; Ben Hamida, Elyes

    2015-09-01

    Wireless body area networks (WBAN) has penetrated immensely in revolutionizing the classical heath-care system. Recently, number of WBAN applications has emerged which introduce potential limits to existing solutions. In particular, IEEE 802.15.6 standard has provided great flexibility, provisions and capabilities to deal emerging applications. In this paper, we investigate the application-specific throughput analysis by fine-tuning the physical (PHY) and medium access control (MAC) parameters of the IEEE 802.15.6 standard. Based on PHY characterizations in narrow band, at the MAC layer, carrier sense multiple access collision avoidance (CSMA/CA) and scheduled access protocols are extensively analyzed. It is concluded that, IEEE 802.15.6 standard can satisfy most of the WBANs applications throughput requirements by maximum achieving 680 Kbps. However, those emerging applications which require high quality audio or video transmissions, standard is not able to meet their constraints. Moreover, delay, energy efficiency and successful packet reception are considered as key performance metrics for comparing the MAC protocols. CSMA/CA protocol provides the best results to meet the delay constraints of medical and non-medical WBAN applications. Whereas, the scheduled access approach, performs very well both in energy efficiency and packet reception ratio.

  16. Study on additional carrier sensing for IEEE 802.15.4 wireless sensor networks.

    Science.gov (United States)

    Lee, Bih-Hwang; Lai, Ruei-Lung; Wu, Huai-Kuei; Wong, Chi-Ming

    2010-01-01

    Wireless sensor networks based on the IEEE 802.15.4 standard are able to achieve low-power transmissions in the guise of low-rate and short-distance wireless personal area networks (WPANs). The slotted carrier sense multiple access with collision avoidance (CSMA/CA) is used for contention mechanism. Sensor nodes perform a backoff process as soon as the clear channel assessment (CCA) detects a busy channel. In doing so they may neglect the implicit information of the failed CCA detection and further cause the redundant sensing. The blind backoff process in the slotted CSMA/CA will cause lower channel utilization. This paper proposes an additional carrier sensing (ACS) algorithm based on IEEE 802.15.4 to enhance the carrier sensing mechanism for the original slotted CSMA/CA. An analytical Markov chain model is developed to evaluate the performance of the ACS algorithm. Both analytical and simulation results show that the proposed algorithm performs better than IEEE 802.15.4, which in turn significantly improves throughput, average medium access control (MAC) delay and power consumption of CCA detection.

  17. On IEEE 802.15.6 IR-UWB receivers - simulations for DBPSK modulation.

    Science.gov (United States)

    Niemelä, Ville; Hämäläinen, Matti; Iinatti, Jari

    2013-01-01

    In 2002, Federal Communications Commission (FCC) was the first in defining regulations for ultra wideband (UWB) communications followed by Europe and Japan some years later. Focusing on impulse radio (IR) UWB, in 2007 was the time for the first published standard targeting in personal area networks, released by the IEEE. The second IEEE released standard including UWB definitions is targeted for wireless body area networks (WBAN) and was published in 2012. As the wireless communications has been and will be passing through almost any levels in society, the natural step with WBAN is using it in different medical, healthcare and wellbeing applications. The arguments for these are related to the modern lifestyle, in which people have increasingly more free time and are more interested in taking care of their health and wellbeing. Another challenge is the population composition, i.e., aging in developed countries which call for new solutions and procedures, particularly from cost wise. In this paper, we are evaluating UWB receivers based on the IEEE 802.15.6 physical layer definitions and capable of detecting differentially encoded modulation. The evaluation is performed using two different WBAN channel models.

  18. A versatile electrical penetration design qualified to IEEE Std. 317-1983

    International Nuclear Information System (INIS)

    Lankenau, W.; Wetherill, T.M.

    1994-01-01

    Although worldwide demand for new construction of nuclear power stations has been on a decline, the available opportunities for the design and construction of qualified electrical penetrations continues to offer challenges, requiring a highly versatile design. Versatility is necessary in order to meet unique customer requirements within the constraints of a design basis qualified to IEEE Std. 317-1983. This paper summarizes such a versatile electrical penetration designed, built and tested to IEEE Std. 317-1983. The principal features are described including major materials of construction. Some of the design constraints such as sealing requirements, and conductor density (including numerical example) are discussed. The requirements for qualification testing of the penetration assembly to IEEE Std. 317-1983 are delineated in a general sense, and some typical test ranges for preconditioning, radiation exposure, and LOCA are provided. The paper concludes by describing ways in which this versatile design has been adapted to meet unique customer requirements in a variety of nuclear power plants

  19. Segmentized Clear Channel Assessment for IEEE 802.15.4 Networks.

    Science.gov (United States)

    Son, Kyou Jung; Hong, Sung Hyeuck; Moon, Seong-Pil; Chang, Tae Gyu; Cho, Hanjin

    2016-06-03

    This paper proposed segmentized clear channel assessment (CCA) which increases the performance of IEEE 802.15.4 networks by improving carrier sense multiple access with collision avoidance (CSMA/CA). Improving CSMA/CA is important because the low-power consumption feature and throughput performance of IEEE 802.15.4 are greatly affected by CSMA/CA behavior. To improve the performance of CSMA/CA, this paper focused on increasing the chance to transmit a packet by assessing precise channel status. The previous method used in CCA, which is employed by CSMA/CA, assesses the channel by measuring the energy level of the channel. However, this method shows limited channel assessing behavior, which comes from simple threshold dependent channel busy evaluation. The proposed method solves this limited channel decision problem by dividing CCA into two groups. Two groups of CCA compare their energy levels to get precise channel status. To evaluate the performance of the segmentized CCA method, a Markov chain model has been developed. The validation of analytic results is confirmed by comparing them with simulation results. Additionally, simulation results show the proposed method is improving a maximum 8.76% of throughput and decreasing a maximum 3.9% of the average number of CCAs per packet transmission than the IEEE 802.15.4 CCA method.

  20. Spectrum Hole Identification in IEEE 802.22 WRAN using Unsupervised Learning

    Directory of Open Access Journals (Sweden)

    V. Balaji

    2016-01-01

    Full Text Available In this paper we present a Cooperative Spectrum Sensing (CSS algorithm for Cognitive Radios (CR based on IEEE 802.22Wireless Regional Area Network (WRAN standard. The core objective is to improve cooperative sensing efficiency which specifies how fast a decision can be reached in each round of cooperation (iteration to sense an appropriate number of channels/bands (i.e. 86 channels of 7MHz bandwidth as per IEEE 802.22 within a time constraint (channel sensing time. To meet this objective, we have developed CSS algorithm using unsupervised K-means clustering classification approach. The received energy level of each Secondary User (SU is considered as the parameter for determining channel availability. The performance of proposed algorithm is quantified in terms of detection accuracy, training and classification delay time. Further, the detection accuracy of our proposed scheme meets the requirement of IEEE 802.22 WRAN with the target probability of falsealrm as 0.1. All the simulations are carried out using Matlab tool.

  1. Analysis and Enhancement of IEEE 802.15.4e DSME Beacon Scheduling Model

    Directory of Open Access Journals (Sweden)

    Kwang-il Hwang

    2014-01-01

    Full Text Available In order to construct a successful Internet of things (IoT, reliable network construction and maintenance in a sensor domain should be supported. However, IEEE 802.15.4, which is the most representative wireless standard for IoT, still has problems in constructing a large-scale sensor network, such as beacon collision. To overcome some problems in IEEE 802.15.4, the 15.4e task group proposed various different modes of operation. Particularly, the IEEE 802.15.4e deterministic and synchronous multichannel extension (DSME mode presents a novel scheduling model to solve beacon collision problems. However, the DSME model specified in the 15.4e draft does not present a concrete design model but a conceptual abstract model. Therefore, in this paper we introduce a DSME beacon scheduling model and present a concrete design model. Furthermore, validity and performance of DSME are evaluated through experiments. Based on experiment results, we analyze the problems and limitations of DSME, present solutions step by step, and finally propose an enhanced DSME beacon scheduling model. Through additional experiments, we prove the performance superiority of enhanced DSME.

  2. A Novel Prioritization Scheme to Improve QoS in IEEE 802.11e Networks

    Directory of Open Access Journals (Sweden)

    Navid Tadayon

    2010-01-01

    Full Text Available IEEE 802.11 WLAN utilizes a distributed function at its MAC layer, namely, DCF to access the wireless medium. Due to its distributed nature, DCF is able to guarantee working stability in a wireless medium while maintaining the assembling and maintenance cost in a low level. However, DCF is inefficient in dealing with real-time traffics due to its incapability on providing QoS. IEEE 802.11e was introduced as a supplementary standard to cope with this problem. This standard introduces an Enhanced Distributed Coordination Function (EDCF that works based on diff-Serve model and can serve multiple classes of traffics (by using different prioritizations schemes. With the emergence of new time-sensitive applications, EDCF has proved to be yet inefficient in dealing with these kinds of traffics because it could not provide network with well-differentiated QoS. In this study, we propose a novel prioritization scheme to improve QoS level in IEEE 802.11e network. In this scheme, we replace Uniform PDF with Gamma PDF, which has salient differentiating properties. We investigate the suitability and superiority of this scheme on furnishing network with well-differentiated QoS using probabilistic analysis. We strengthen our claims by extensive simulation runs.

  3. IEEE 693 seismic qualification of composites for substation high-voltage equipment

    Energy Technology Data Exchange (ETDEWEB)

    Schiff, A.J. [Precision Measurement Instruments, Los Altos Hills, CA (United States); Kempner, L.Jr. [Bonneville Power Administration, Vancouver, BC (Canada)

    2004-07-01

    Standard 693-1997 of the Institute of Electrical and Electronic Engineers (IEEE) is the recommended practice for seismic design of substations. It represents a significant improvement in the way the power industry seismically qualifies substation high-voltage equipment. This paper described the use of IEEE Standard 693 for hollow-core composite insulators that are used on high-voltage transformers and demonstrated that changes are warranted. The following four failure modes associated with the composite insulator were discussed: bond degradation, bond failure, tube degradation and tube layer delamination. The authors evaluated the IEEE 693 qualification procedure of time history shake-table and static-pull tests and were concerned about acceptance criteria. It was shown that acceptance criteria are not valid for qualifying hollow-core composites and that static-pull tests are needed after the vibration qualification tests are completed. It was suggested that more research is warranted to determine if bonding at the top part of the flange can be eliminated, thereby eliminating bond degradation. The resulting increase in system damping would improve the dynamic response of the unit. 1 ref., 10 figs.

  4. Ultrasonic imaging of projected components of PFBR

    Energy Technology Data Exchange (ETDEWEB)

    Sylvia, J.I., E-mail: sylvia@igcar.gov.in [Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamil Nadu (India); Jeyan, M.R.; Anbucheliyan, M.; Asokane, C.; Babu, V. Rajan; Babu, B.; Rajan, K.K.; Velusamy, K.; Jayakumar, T. [Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamil Nadu (India)

    2013-05-15

    Highlights: ► Under sodium ultrasonic scanner in PFBR is for detecting protruding objects. ► Feasibility study for detecting Absorber rods and its drive mechanisms. ► Developed in-house PC based ultrasonic imaging system. ► Different case studies were carried out on simulated ARDM's. ► Implemented the experimental results to PFBR application. -- Abstract: The 500 MWe, sodium cooled, Prototype Fast Breeder Reactor (PFBR) is under advanced stage of construction at Kalpakkam in India. Opacity of sodium restricts visual inspection of components immersed in sodium by optical means. Ultrasonic wave passes through sodium hence ultrasonic techniques using under sodium ultrasonic scanners are developed to obtain under sodium images. The main objective of such an Under Sodium Ultrasonic Scanner (USUSS) for Prototype Fast Breeder Reactor (PFBR) is to detect and ensure that no core Sub Assembly (SA) or Absorber Rod or its Drive Mechanism is protruded in the above core plenum before starting the fuel handling operation. Hence, it is necessary to detect and locate the object, if it is protruding the above core plenum. To study the feasibility of detecting the absorber rods and their drive mechanisms using direct ultrasonic imaging technique, experiments were carried out for different orientations and profiles of the projected components in a 5 m diameter water tank. The in-house developed PC based ultrasonic scanning system is used for acquisition and analysis of data. The pseudo three dimensional color images obtained are discussed and the results are applicable for PFBR. This paper gives the details of the features of the absorber rods and their drive mechanisms, their orientation in the reactor core, experimental setup, PC based ultrasonic scanning system, ultrasonic images and the discussion on the results.

  5. Technical aspects of trans reduction in margarines

    Directory of Open Access Journals (Sweden)

    Van Duijn Gerrit

    2000-01-01

    Full Text Available The opinion of nutritional science on the effect of trans fatty acids on blood cholesterol has drastically changed during the last decade. As a reaction to these new findings, the European margarine industry decided in the mid nineties to eliminate trans containing components from their margarine fat phase compositions. This excluded practically the use of partially hydrogenated oils and fats. Trans-free margarines have been introduced with optimised fat crystal structures stabilising a maximum of water in oil emulsion with a minimum of solid fat phase. These fat crystal structures are formed by fat phase components obtained from interesterification and/or fractionation of non-hydrogenated and/or fully hydrogenated feedstocks.

  6. Physics of Trans-Planckian Gravity

    CERN Document Server

    Dvali, Gia; Germani, Cristiano

    2011-01-01

    We study aspects of the phenomenon of gravitational UV-self-completeness and its implications for deformations of Einstein gravity. In a ghost-free theory flowing to Einstein gravity in the IR trans-Planckian propagating quantum degrees of freedom cannot exist. The only physical meaning of a trans-Planckian pole is the one of a classical state (Black Hole) which is fully described by the light IR quantum degrees of freedom and gives exponentially-suppressed contributions to virtual processes. In this sense Einstein gravity is UV self-complete, although not Wilsonian. We show that this UV/IR correspondence puts a severe constraint on any attempt of conventional Wilsonian UV-completion of trans-Planckian gravity. In particular, there is no well-defined energy domain in which gravity could become asymptotically weak or safe.

  7. 21 CFR 882.1925 - Ultrasonic scanner calibration test block.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ultrasonic scanner calibration test block. 882... Ultrasonic scanner calibration test block. (a) Identification. An ultrasonic scanner calibration test block is a block of material with known properties used to calibrate ultrasonic scanning devices (e.g., the...

  8. Ruminant and industrially produced trans fatty acids

    DEFF Research Database (Denmark)

    Stender, Steen; Astrup, Arne; Dyerberg, Jørn

    2008-01-01

    % of the fatty acids in trans form compared to the content in ruminant fat which generally does not exceed 6%. In Western Europe, including Scandinavia, the average daily intake of IP-TFA has decreased during the recent decade due to societal pressure and a legislative ban, whereas the intake of RP-TFA has......Fatty acids of trans configuration in our food come from two different sources - industrially produced partially hydrogenated fat (IP-TFA) used in frying oils, margarines, spreads, and in bakery products, and ruminant fat in dairy and meat products (RP-TFA). The first source may contain up to 60...

  9. Ultrasonic relaxations in borate glasses

    International Nuclear Information System (INIS)

    D'Angelo, G.; Tripodo, G.; Carini, G.; Cosio, E.; Bartolotta, A.; Di Marco, G.

    2004-01-01

    The attenuation and velocity of ultrasonic waves of frequencies in the range from 10 to 70 MHz have been measured in M 2 O-B 2 O 3 borate glasses (M: Li or Ag) as a function of temperature between 15 and 350 K. The velocity of sound waves decreases with increasing temperature in all the glasses, the decrease as the temperature is increased is larger in glasses containing silver than in those with lithium. A broad relaxation peak characterises the attenuation behaviour of the lithium and silver borate glasses at temperatures below 100 K and is paralleled by a corresponding dispersive behaviour of the sound velocity. Above 100 K, the ultrasonic velocity shows a nearly linear behaviour regulated by the vibrational anharmonicity, which decreases with increasing content of modifier oxide and is smaller in lithium than in silver borates. These results suggest that the relaxation of structural defects and the anharmonicity of borate glasses are strongly affected by two parameters: the number of bridging bonds per network forming ion and the polarising power of network modifier ions which occupy sites in the existing interstices

  10. Dynamics of ultrasonic additive manufacturing.

    Science.gov (United States)

    Hehr, Adam; Dapino, Marcelo J

    2017-01-01

    Ultrasonic additive manufacturing (UAM) is a solid-state technology for joining similar and dissimilar metal foils near room temperature by scrubbing them together with ultrasonic vibrations under pressure. Structural dynamics of the welding assembly and work piece influence how energy is transferred during the process and ultimately, part quality. To understand the effect of structural dynamics during UAM, a linear time-invariant model is proposed to relate the inputs of shear force and electric current to resultant welder velocity and voltage. Measured frequency response and operating performance of the welder under no load is used to identify model parameters. Using this model and in-situ measurements, shear force and welder efficiency are estimated to be near 2000N and 80% when welding Al 6061-H18 weld foil, respectively. Shear force and welder efficiency have never been estimated before in UAM. The influence of processing conditions, i.e., welder amplitude, normal force, and weld speed, on shear force and welder efficiency are investigated. Welder velocity was found to strongly influence the shear force magnitude and efficiency while normal force and weld speed showed little to no influence. The proposed model is used to describe high frequency harmonic content in the velocity response of the welder during welding operations and coupling of the UAM build with the welder. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. Deconvolution algorithms applied in ultrasonics

    International Nuclear Information System (INIS)

    Perrot, P.

    1993-12-01

    In a complete system of acquisition and processing of ultrasonic signals, it is often necessary at one stage to use some processing tools to get rid of the influence of the different elements of that system. By that means, the final quality of the signals in terms of resolution is improved. There are two main characteristics of ultrasonic signals which make this task difficult. Firstly, the signals generated by transducers are very often non-minimum phase. The classical deconvolution algorithms are unable to deal with such characteristics. Secondly, depending on the medium, the shape of the propagating pulse is evolving. The spatial invariance assumption often used in classical deconvolution algorithms is rarely valid. Many classical algorithms, parametric and non-parametric, have been investigated: the Wiener-type, the adaptive predictive techniques, the Oldenburg technique in the frequency domain, the minimum variance deconvolution. All the algorithms have been firstly tested on simulated data. One specific experimental set-up has also been analysed. Simulated and real data has been produced. This set-up demonstrated the interest in applying deconvolution, in terms of the achieved resolution. (author). 32 figs., 29 refs

  12. Ultrasonic Characterization of Aerospace Composites

    Science.gov (United States)

    Leckey, Cara; Johnston, Patrick; Haldren, Harold; Perey, Daniel

    2015-01-01

    Composite materials have seen an increased use in aerospace in recent years and it is expected that this trend will continue due to the benefits of reduced weight, increased strength, and other factors. Ongoing work at NASA involves the investigation of the large-scale use of composites for spacecraft structures (SLS components, Orion Composite Crew Module, etc). NASA is also involved in work to enable the use of composites in advanced aircraft structures through the Advanced Composites Project (ACP). In both areas (space and aeronautics) there is a need for new nondestructive evaluation and materials characterization techniques that are appropriate for characterizing composite materials. This paper will present an overview of NASA's needs for characterizing aerospace composites, including a description of planned and ongoing work under ACP for the detection of composite defects such as fiber waviness, reduced bond strength, delamination damage, and microcracking. The research approaches include investigation of angle array, guided wave, and phase sensitive ultrasonic methods. The use of ultrasonic simulation tools for optimizing and developing methods will also be discussed.

  13. Ultrasonic inspection of inpile tubes

    International Nuclear Information System (INIS)

    Boyd, D.M.; Bossi, H.

    1985-01-01

    The in-service inspection (ISI) of inpile tubes can be performed accurately and safely with a semiautomatic ultrasonic inspection system. The ultrasonic technique uses a set of multiple transducers to detect and size cracks, voids, and laminations radially and circumferentially. Welds are also inspected for defects. The system is designed to inspect stainless steel and Inconel tubes ranging from 53.8 mm (2.12 in.) to 101.6 mm (4 in.) inner diameter with wall thickness on the order of 5 mm. The inspection head contains seven transducers mounted in a surface-following device. Six angle-beam transducers generate shear waves in the tubes. Two of the six are oriented to detect circumferential cracks, and two detect axial cracks. Although each of these four transducers is used in the pulse-echo mode, they are oriented in aligned sets so pitch-catch operation is possible if desired. The remaining angle-beam transducers are angulated to detect flaws that are off axial or circumferential orientation. The seventh transducer is used for longitudinal inspection and detects and sizes laminar-type defects

  14. Calculations for piezoelectric ultrasonic transducers

    International Nuclear Information System (INIS)

    Jensen, H.

    1986-05-01

    Analysis of piezoelectric ultrasonic transducers implies a solution of a boundary value problem, for a body which consists of different materials, including a piezoelectric part. The problem is dynamic at frequencies, where a typical wavelength is somewhat less than the size of the body. Radiation losses as well as internal losses may be important. Due to the complexity of the problem, a closed form solution is the exception rather than the rule. For this reason, it is necessary to use approximate methods for the analysis. Equivalent circuits, the Rayleigh-Ritz method, Mindlin plate theory and in particular the finite element method are considered. The finite element method is utilized for analysis of axisymmetric transducers. An explicit, fully piezoelectric, triangular ring element, with linear variations in displacement and electric potential is given. The influence of a fluid half-space is also given, in the form of a complex stiffness matrix. A special stacking procedure, for analysis of the backing has been developed. This procedure gives a saving, which is similar to that of the fast fourier transform algorithm, and is also wellsuited for analysis of finite and infinite waveguides. Results obtained by the finite element method are shown and compared with measurements and exact solutions. Good agreement is obtained. It is concluded that the finite element method can be a valueable tool in analysis and design of ultrasonic transducers. (author)

  15. Conference Proceedings for 1997 IEEE 24th International Conference on Plasma Sciences, 19 - 22 May 1997, San Diego, California

    National Research Council Canada - National Science Library

    Hyman, Julius

    1997-01-01

    This 360 page softbound publication includes the following major sections, An invitation to ICOPS'97, Catamaran Resort Hotel Floor Pinas, Officers of the IEEE Nuclear and Plasma Sciences Society, Conference Information...

  16. NIH-IEEE 2015 Strategic Conference on Healthcare Innovations and Point-of-Care Technologies for Prec

    Science.gov (United States)

    NIH and the Institute for Electrical and Electronics Engineering, Engineering in Medicine and Biology Society (IEEE/EMBS) hosted the third iteration of the Healthcare Innovations and Point-of-Care Technologies Conference last week.

  17. Study of Allocation Guaranteed Time Slot Wireless Body Area Networks Based on IEEE 802.15.4

    Science.gov (United States)

    Yundra, E.; Harsono, G. D.

    2018-04-01

    This paper aims to determine the size of the Guaranteed Time Slot (GTS) on the super frame structure required for each sensor as well as to know the performance of the GTS resized system compared to the GTS standard on IEEE 802.15.4. This article proposes a scheme to improve IEEE 802.15.4 medium access control, called allocation Guaranteed Time Slot (ALGATIS). ALGATIS is expected to effectively allocate guaranteed time slot to the requested sensors, it adjusts the length of the slot in super frame duration based on the length of the packet data. This article presents a simulation experiment of IEEE 802.15.4, especially for star network, to predict the throughput of networks and average energy consumption. The simulation experiments show that the performance of ALGATIS is better than that of IEEE 802.15.4 standard in term of the throughput of networks and average energy consumption

  18. Performance Analysis of IEEE 802.11g TCM Waveforms Transmitted over a Channel with Pulse-Noise Interference

    National Research Council Canada - National Science Library

    Drivas, Athanasios

    2007-01-01

    .... The application of TCM combines FEC coding and M-ary modulation in one operation. The objective of this thesis is to investigate the performance of an orthogonal frequency-division multiplexing (OFDM) based IEEE...

  19. Implementation of DoS attack and mitigation strategies in IEEE 802.11b/g WLAN

    Science.gov (United States)

    Deng, Julia; Meng, Ke; Xiao, Yang; Xu, Roger

    2010-04-01

    IEEE 802.11 wireless Local Area Network (WLAN) becomes very prevalent nowadays. Either as a simple range extender for a home wired Ethernet interface, or as a wireless deployment throughout an enterprise, WLAN provides mobility, convenience, and low cost. However, an IEEE 802.11b/g wireless network uses the frequency of unlicensed 2.4GHz, which makes the network unsafe and more vulnerable than traditional Ethernet networks. As a result, anyone who is familiar with wireless network may initiate a Denial of Service (DoS) attack to influence the common communication of the network or even make it crash. In this paper, we present our studies on the DoS attacks and mitigation strategies for IEEE 802.11b/g WLANs and describe some initial implementations using IEEE 802.11b/g wireless devices.

  20. Implementation of IEEE-1588 timing and synchronization for ATCA control and data acquisition systems

    International Nuclear Information System (INIS)

    Correia, Miguel; Sousa, Jorge; Combo, Álvaro; Rodrigues, António P.; Carvalho, Bernardo B.; Batista, António J.N.; Gonçalves, Bruno; Correia, Carlos M.B.A.; Varandas, Carlos A.F.

    2012-01-01

    Highlights: ► IEEE-1588 over Ethernet protocol is implemented for the synchronization of all clock signals of an ATCA AMC carrier module. ► The ATCA hardware consists of an AMC quad-carrier main-board with PCI Express switching. ► IEEE-1588 is to be implemented on a Virtex-6 FPGA. ► Timing signals on the ATX-AMC4-PTP are managed and routed by a crosspoint-switch implemented on a Virtex-6 FPGA. ► Each clock signal source may be independently located (on each of the AMC cards, RTM or ATCA backplane). - Abstract: Control and data acquisition (C and DA) systems for Fusion experiments are required to provide accurate timing and synchronization (T and S) signals to all of its components. IPFN adopted PICMG's Advanced Telecommunications Computing Architecture (ATCA) industry standard to develop C and DA instrumentation. ATCA was chosen not only for its high throughput characteristics but also for its high availability (HA) features which become of greater importance in steady-state operation scenarios. However, the specified ATCA clock and synchronization interface may be too limited for the timing and synchronization needs in advanced Physics experiments. Upcoming specification extensions, developed by the “xTCA for Physics” workgroups, will contemplate, among others, a complementary timing specification, developed by the PICMG xTCA for Physics IO, Timing and Synchronization Technical Committee. The IEEE-1588 Precision Time Protocol (PTP) over Ethernet is one of the protocols, proposed by the Committee, aiming for precise synchronization of clocks in measurement and control systems, based on low jitter and slave-to-slave skew criteria. The paper presents an implementation of IEEE-1588 over Ethernet, in an ATCA hardware platform. The ATCA hardware consists of an Advanced Mezzanine Card (AMC) quad-carrier front board with PCI Express switching. IEEE-1588 is to be implemented on a Virtex-6 FPGA. Ethernet connectivity with the remote master clock is located on

  1. Biotransformation of trans-1-chloro-3,3,3-trifluoropropene (trans-HCFO-1233zd)

    International Nuclear Information System (INIS)

    Schmidt, Tobias; Bertermann, Rüdiger; Rusch, George M.; Tveit, Ann; Dekant, Wolfgang

    2013-01-01

    trans-1-Chloro-3,3,3-trifluoropropene (trans-HCFO-1233zd) is a novel foam blowing and precision cleaning agent with a very low impact for global warming and ozone depletion. trans-HCFO-1233zd also has a low potential for toxicity in rodents and is negative in genotoxicity testing. The biotransformation of trans-HCFO-1233zd and kinetics of metabolite excretion with urine were assessed in vitro and in animals after inhalation exposures. For in vitro characterization, liver microsomes from rats, rabbits and humans were incubated with trans-HCFO-1233zd. Male Sprague Dawley rats and female New Zealand White rabbits were exposed to 2,000, 5,000 and 10,000 ppm for 6 h and urine was collected for 48 h after the end of the exposure. Study specimens were analyzed for metabolites using 19 F NMR, LC-MS/MS and GC/MS. S-(3,3,3-trifluoro-trans-propenyl)-glutathione was identified as predominant metabolite of trans-HCFO-1233zd in all microsomal incubation experiments in the presence of glutathione. Products of the oxidative biotransformation of trans-HCFO-1233zd were only minor metabolites when glutathione was present. In rats, both 3,3,3-trifluorolactic acid and N-acetyl-(3,3,3-trifluoro-trans-propenyl)-L-cysteine were observed as major urinary metabolites. 3,3,3-Trifluorolactic acid was not detected in the urine of rabbits. Quantitation showed rapid excretion of both metabolites in both species (t 1/2 1/2 < 6 h). ► Glutathione adduct as predominant in vitro metabolite in all tested species. ► Toxic metabolites could not be detected in any great extent

  2. Biotransformation of trans-1-chloro-3,3,3-trifluoropropene (trans-HCFO-1233zd)

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Tobias [Institut für Toxikologie, Universität Würzburg, Versbacher Str. 9, 97078 Würzburg (Germany); Bertermann, Rüdiger [Institut für Anorganische Chemie, Universität Würzburg, Am Hubland, 97074 Würzburg (Germany); Rusch, George M.; Tveit, Ann [Honeywell, P.O. Box 1057, Morristown, NJ 07962-1057 (United States); Dekant, Wolfgang, E-mail: dekant@toxi.uni-wuerzburg.de [Institut für Toxikologie, Universität Würzburg, Versbacher Str. 9, 97078 Würzburg (Germany)

    2013-05-01

    trans-1-Chloro-3,3,3-trifluoropropene (trans-HCFO-1233zd) is a novel foam blowing and precision cleaning agent with a very low impact for global warming and ozone depletion. trans-HCFO-1233zd also has a low potential for toxicity in rodents and is negative in genotoxicity testing. The biotransformation of trans-HCFO-1233zd and kinetics of metabolite excretion with urine were assessed in vitro and in animals after inhalation exposures. For in vitro characterization, liver microsomes from rats, rabbits and humans were incubated with trans-HCFO-1233zd. Male Sprague Dawley rats and female New Zealand White rabbits were exposed to 2,000, 5,000 and 10,000 ppm for 6 h and urine was collected for 48 h after the end of the exposure. Study specimens were analyzed for metabolites using {sup 19}F NMR, LC-MS/MS and GC/MS. S-(3,3,3-trifluoro-trans-propenyl)-glutathione was identified as predominant metabolite of trans-HCFO-1233zd in all microsomal incubation experiments in the presence of glutathione. Products of the oxidative biotransformation of trans-HCFO-1233zd were only minor metabolites when glutathione was present. In rats, both 3,3,3-trifluorolactic acid and N-acetyl-(3,3,3-trifluoro-trans-propenyl)-L-cysteine were observed as major urinary metabolites. 3,3,3-Trifluorolactic acid was not detected in the urine of rabbits. Quantitation showed rapid excretion of both metabolites in both species (t{sub 1/2} < 6 h) and the extent of biotransformation of trans-HCFO-1233zd was determined as approximately 0.01% of received dose in rabbits and approximately 0.002% in rats. trans-HCFO-1233zd undergoes both oxidative biotransformation and glutathione conjugation at very low rates. The low extent of biotransformation and the rapid excretion of metabolites formed are consistent with the very low potential for toxicity of trans-HCFO-1233zd in mammals. - Highlights: ► No lethality and clinical signs were observed. ► Glutathione S-transferase and cytochrome P-450 dependent

  3. Quality control of disinfection in ultrasonic baths

    Energy Technology Data Exchange (ETDEWEB)

    Schoene, H. [Technical University Dresden (Germany). Faculty of Mechanical Engineering; Jatzwauk, L. [University Hospital of the Technical University Dresden (Germany). Abt. Krankenhaushygiene

    2002-07-01

    Numerous investigations under laboratory conditions confirmed the microbicidal efficacy of ultrasonication. Morphological destruction was shown on bacteria and fungi as well as on different virus species. Ultrasonic treatment seems to increase the effect of different antibiotics and disinfectants. Reasons for this synergism are largely unknown and uninvestigated, but the active principle seems to bee the dispersing effect of ultrasonication in combination with the destruction of cell wall or cell membrane. Unfortunately no validation of test conditions exists for most of these investigations, regarding intensity and frequency of ultrasonic waves, temperature of liquid medium and measurement of cavitation which is an essential part of physical and chemical effects in ultrasonic baths. In contrast to most laboratory experiments sound density of ultrasound for treatment of medical instruments is below 1 W/cm{sup 2} because instruments will be destroyed under stronger ultrasonic conditions. The frequency is below 50 KHz. This paper describes bactericidal and fungicidal effects of low- intensity-ultrasonication and its synergistical support to chemical disinfection. (orig.)

  4. Ultrasonic tests on materials with protective coatings

    International Nuclear Information System (INIS)

    Whaley, H.L.

    1977-01-01

    Protective coatings are applied to some nuclear components such as reactor vessels to inhibit surface corrosion. Since in-service ultrasonic inspection is required for such components, a study was performed to determine whether the use of protective coatings can affect ultrasonic tests. Two 2 in. thick steel plates were uniformly machined, sandblasted, and used as bases for two types of protective coatings. The type and thickness of the coating and the presence of contamination, such as fingerprints or mild oxidation under the paint, were the independent variables associated with the coating. Tests were run to determine the effects of the protective coatings on ultrasonic tests conducted on the steel plates. Significant variations in ultrasonic test sensitivity occurred as a function of the type and thickness of protective coating, couplant (material that conducts the ultrasound from the transducer into the test part, normally water or some type of oil), transducer wear plate, and ultrasonic test frequency. Ultrasonic tests can be strongly affected by a protective coating on the component to be inspected. As compared to the test sensitivity for an uncoated reference sample, the sensitivity may be dramatically shifted up or down on the coated surface. In certain coating thickness ranges, the sensitivity can fluctuate widely with small changes in coating thickness. If a coating is chosen properly, however, components with protective coatings can be tested ultrasonically with valid results. These results are for the case of ultrasonic input on the coated surface. It is not expected that an ultrasonic test conducted from the front surface would be appreciably affected by a coating on the rear surface

  5. Powdered activated carbon adsorption of two fishy odorants in water: Trans,trans-2,4-heptadienal and trans,trans-2,4-decadienal.

    Science.gov (United States)

    Li, Xin; Wang, Jun; Zhang, Xiaojian; Chen, Chao

    2015-06-01

    Powdered activated carbon (PAC) adsorption of two fishy odorants, trans,trans-2,4-heptadienal (HDE) and trans,trans-2,4-decadienal (DDE), was investigated. Both the pseudo first-order and the pseudo second-order kinetic models well described the kinetics curves, and DDE was more readily removed by PAC. In isotherm tests, both Freundlich and Modified Freundlich isotherms fitted the experimental data well. PAC exhibited a higher adsorption capacity for DDE than for HDE, which could be ascribed to the difference in their hydrophobicity. The calculated thermodynamic parameters (ΔG0, ΔH0, and ΔS0) indicated an exothermic and spontaneous adsorption process. PAC dosage, pH, and natural organic matter (NOM) presence were found to influence the adsorption process. With increasing PAC dosage, the pseudo first-order and pseudo second-order rate constants both increased. The value of pH had little influence on HDE or DDE molecules but altered the surface charge of PAC, and the maximum adsorption capacity occurred at pH9. The presence of NOM, especially the fraction with molecular weight less than 1k Dalton, hindered the adsorption. The study showed that preloaded NOM impaired the adsorption capacity of HDE or DDE more severely than simultaneously fed NOM did. Copyright © 2015. Published by Elsevier B.V.

  6. Trans-kingdom cross-talk

    DEFF Research Database (Denmark)

    Knip, Marijn; Constantin, Maria-Ermioni; Thordal-Christensen, Hans

    2014-01-01

    This review focuses on the mobility of small RNA (sRNA) molecules from the perspective of trans-kingdom gene silencing. Mobility of sRNA molecules within organisms is a well-known phenomenon, facilitating gene silencing between cells and tissues. sRNA signals are also transmitted between organism...

  7. The european Trans-Tools transport model

    NARCIS (Netherlands)

    Rooijen, T. van; Burgess, A.

    2008-01-01

    The paper presents the use of ArcGIS in the Transtools Transport Model, TRANS-TOOLS, created by an international consortium for the European Commission. The model describe passenger as well as freight transport in Europe with all medium and long distance modes (cars, vans, trucks, train, inland

  8. Computer simulation of ultrasonic waves in solids

    International Nuclear Information System (INIS)

    Thibault, G.A.; Chaplin, K.

    1992-01-01

    A computer model that simulates the propagation of ultrasonic waves has been developed at AECL Research, Chalk River Laboratories. This program is called EWE, short for Elastic Wave Equations, the mathematics governing the propagation of ultrasonic waves. This report contains a brief summary of the use of ultrasonic waves in non-destructive testing techniques, a discussion of the EWE simulation code explaining the implementation of the equations and the types of output received from the model, and an example simulation showing the abilities of the model. (author). 2 refs., 2 figs

  9. Ultrasonic characterization of vegetable oil product

    International Nuclear Information System (INIS)

    Sidek Hj Abd Aziz; Chow Sai Pew; Abdul Halim Shaari; Nor Azizah Shaari

    1992-01-01

    The ultrasonic wave velocity and attenuation of a number vegetable oil products were measured using an ultrasonic pulse echo overlap technique from room temperature up to 90 0 C. Among the liquid samples studied were refined bleach deodorized (RED) palm oil, palm olein, coconut oil, corn oil and soya bean oil. The velocity of sound in vegetable oil products varies from about 1200 to 200 ms-1 and decrease linearly as the temperature increases. The ultrasonic properties of the oil are much dependent on their viscosity, density, relaxation effect and vibrational anharmonicity

  10. On-line ultrasonic gas entrainment monitor

    International Nuclear Information System (INIS)

    Day, C.K.; Pedersen, H.N.

    1978-01-01

    Apparatus employing ultrasonic energy for detecting and measuring the quantity of gas bubbles present in liquids being transported through pipes is described. An ultrasonic transducer is positioned along the longitudinal axis of a fluid duct, oriented to transmit acoustic energy radially of the duct around the circumference of the enclosure walls. The back-reflected energy is received centrally of the duct and interpreted as a measure of gas entrainment. One embodiment employs a conical reflector to direct the transmitted acoustic energy radially of the duct and redirect the reflected energy back to the transducer for reception. A modified embodiment employs a cylindrical ultrasonic transducer for this purpose

  11. Fundamentals and applications of ultrasonic waves

    CERN Document Server

    Cheeke, J David N

    2002-01-01

    Ultrasonics. A subject with applications across all the basic sciences, engineering, medicine, and oceanography, yet even the broader topic of acoustics is now rarely offered at undergraduate levels. Ultrasonics is addressed primarily at the doctoral level, and texts appropriate for beginning graduate students or newcomers to the field are virtually nonexistent.Fundamentals and Applications of Ultrasonic Waves fills that void. Designed specifically for senior undergraduates, beginning graduate students, and those just entering the field, it begins with the fundamentals, but goes well beyond th

  12. Track type ultrasonic inspection device

    International Nuclear Information System (INIS)

    Kajiyama, Shigeru; Sasaki, Tsukasa; Takahisa, Kazuo.

    1993-01-01

    The present invention concerns an improvement of a scanning device disposed near an object to be inspected such as a nuclear pressure vessel and having an ultrasonic probe, mounted thereon that travel along a running track. Specifically, one of wheel supports on both sides is attached being secured to the scanning device. The other of the supports is capable of fixing and releasing, as well as providing and releasing pressure to and from wheels upon mounting and detachment. This enables to provide a structure capable of pressing the wheels of the running device to the plane of the track and release thereof. Accordingly, it is possible to improve the running performance, reduce the size and weight and shorten the time for mounting and detachment of the running inspection device. (I.S.)

  13. Cracks assessment using ultrasonic technology

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, Maria Pia; Tomasella, Marcelo [OLDELVAL S.A. Oleoductos del Valle, Rio Negro (Argentina). Pipeline Integrity Dept.

    2005-07-01

    The goal of Oldelval Integrity Program is to prevent ruptures and leaks, developing strategies for a better handling of the integrity of our pipelines. In order to achieve it we have studied and modeled each process that involved in the integrity pipeline. Those processes are mainly based on defects reported by an internal inspection tool and supplied with field inspection and monitoring data. Years of evaluation, study and the continuous effort overturned towards a phenomenon that worries to the industry, as it is the SCC. Since 1998 up to 2004 SCC was included in the integrity program with some preventive maintenance programs. The accomplishment of the inspection based on ultrasound tools, is the culmination of years of evaluation and investigations supported by field digs and materials susceptibility. This paper describes Oldelval's results with ultrasonic crack detection tool, and how it can be reliably to detect SCC. (author)

  14. Integrated Ultrasonic-Photonic Devices

    DEFF Research Database (Denmark)

    Barretto, Elaine Cristina Saraiva

    in channel waveguides and Mach-Zehnder interferometers. Numerical models are developed based on the finite element method, and applied to several scenarios, such as optimization of the geometrical parameters of waveguides, use of slow light in photonic crystal waveguides and use of Lamb waves in membranized......This thesis deals with the modeling, design, fabrication and characterization of integrated ultrasonic-photonic devices, with particular focus on the use of standard semiconductor materials such as GaAs and silicon. The devices are based on the use of guided acoustic waves to modulate the light...... investigated. Comparisons are made with the numerical and experimental results, and they validate the obtained response of the acoustic and photonic components of the device. Finally, a new design for an optical frequency shifter is proposed, posing several advantages over existing devices in terms of size...

  15. Ultrasonic Histotripsy for Tissue Therapy

    Science.gov (United States)

    Pahk, K. J.; Dhar, D. K.; Malago, M.; Saffari, N.

    2015-01-01

    Hepatocyte transplantation has been considered and investigated as a promising and alternative method to liver transplantation for treating liver-based metabolic disorder in newborns over the past two decades. Although some clinical trials have been conducted and shown clinical benefits and outcomes, it is difficult to deliver and achieve a desired level of integration and transplantation of hepatocytes in the liver parenchyma. To overcome this problem, this work introduces an alternative method to a portal-infused-hepatocyte cell transplantation. To improve the level of engraftment of transplantable hepatocytes, these are injected directly into cavities generated by ultrasonic histotripsy. Histotripsy is an extracorporeal noninvasive technique which has been recently developed using high intensity focused ultrasound (HIFU) for inducing tissue fractionation with no coagulative necrosis. The exact mechanisms for the tissue fractionation are not well understood yet; but the possible mechanisms are thought to be a combination of nonlinear wave propagation effect, explosive bubble growth and ultrasonic atomization. The main objectives of this work are to demonstrate the feasibility of this new cell therapy and evaluate and distinguish between the different types of cavitation activity for either a thermally or a mechanically induced lesion. In the present work, numerical studies on the bubble dynamics (the Gilmore-Akulichev bubble model coupled with the Khokhlov-Zabolotskaya-Kuznetsov equation) and both ex- and in vivo liver experiments are conducted with histological analysis (haematoxylin and eosin stain). The numerical and the experimental results suggest that (a) the acoustic emissions emitted during the thermal ablation and the histotripsy exposure can be distinguished both numerically and experimentally and (b) the proposed cell therapy may potentially form an effective and safe clinical treatment for replacing and correcting disordered hepatocytes, although the

  16. Ultrasonic Histotripsy for Tissue Therapy

    International Nuclear Information System (INIS)

    Pahk, K J; Saffari, N; Dhar, D K; Malago, M

    2015-01-01

    Hepatocyte transplantation has been considered and investigated as a promising and alternative method to liver transplantation for treating liver-based metabolic disorder in newborns over the past two decades. Although some clinical trials have been conducted and shown clinical benefits and outcomes, it is difficult to deliver and achieve a desired level of integration and transplantation of hepatocytes in the liver parenchyma. To overcome this problem, this work introduces an alternative method to a portal-infused-hepatocyte cell transplantation. To improve the level of engraftment of transplantable hepatocytes, these are injected directly into cavities generated by ultrasonic histotripsy. Histotripsy is an extracorporeal noninvasive technique which has been recently developed using high intensity focused ultrasound (HIFU) for inducing tissue fractionation with no coagulative necrosis. The exact mechanisms for the tissue fractionation are not well understood yet; but the possible mechanisms are thought to be a combination of nonlinear wave propagation effect, explosive bubble growth and ultrasonic atomization. The main objectives of this work are to demonstrate the feasibility of this new cell therapy and evaluate and distinguish between the different types of cavitation activity for either a thermally or a mechanically induced lesion. In the present work, numerical studies on the bubble dynamics (the Gilmore-Akulichev bubble model coupled with the Khokhlov-Zabolotskaya-Kuznetsov equation) and both ex- and in vivo liver experiments are conducted with histological analysis (haematoxylin and eosin stain). The numerical and the experimental results suggest that (a) the acoustic emissions emitted during the thermal ablation and the histotripsy exposure can be distinguished both numerically and experimentally and (b) the proposed cell therapy may potentially form an effective and safe clinical treatment for replacing and correcting disordered hepatocytes, although the

  17. Trans-Kullo jagatakse tükkideks / Kadrin Karner

    Index Scriptorium Estoniae

    Karner, Kadrin

    2008-01-01

    Primos OÜ omanik ja Trans-Kullo osanik Endel Siff ütles, et Trans-Kullo on aktsionäride erinevate ärihuvide tõttu läinud jagunemisele, mis võib lõppeda ettevõtte likvideerimisega. Lisa: Trans-Kullo

  18. Ultrasonically-assisted Thermal Stir Welding System

    Science.gov (United States)

    Ding, R. Jeffrey (Inventor)

    2014-01-01

    A welding head assembly has a work piece disposed between its containment plates' opposing surfaces with the work piece being maintained in a plastic state thereof at least in a vicinity of the welding head assembly's stir rod as the rod is rotated about its longitudinal axis. The welding head assembly and the work piece experience relative movement there between in a direction perpendicular to the rod's longitudinal axis as the work piece is subjected to a compressive force applied by the containment plates. A first source coupled to the first containment plate applies a first ultrasonic wave thereto such that the first ultrasonic wave propagates parallel to the direction of relative movement. A second source coupled to the second containment plate applies a second ultrasonic wave thereto such that the second ultrasonic wave propagates parallel to the direction of relative movement.propagates parallel to the direction of relative movement.

  19. Ultrasonic determination of the size of defects

    International Nuclear Information System (INIS)

    Zetterwall, T.

    1989-01-01

    The paper presents results from a study of ultrasonic testing of materials. The main topic has been the determination of the size, length and deep, of cracks or defects in stainless steel plates. (K.A.E)

  20. Advanced ultrasonic technology for natural gas measurement

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-11-15

    In recent years, due to rising environmental and safety concerns, increasing commodity prices, and operational inefficiencies, a paradigm shift has been taking place with respect to gas measurement. The price of natural gas depends on the location, time of the year, and type of consumer. There is wide uncertainty associated with an orifice meter. This paper presents the use of advanced ultrasonic technology for the measurement of natural gas. For many years, multi-path ultrasonic meters with intelligent sensor technology have been used for gas measurement. This paper gives the various applications of ultrasonic technology along with their advantages and a draws a comparison with orifice meters. From the study it can be concluded that extensive advances in the use of ultrasonic technology for gas measurement have widened the areas of application and that varying frequencies combined with sealed transducer designs make it possible to measure atmospheric and sour gas in custody transfer process control and flaring accurately.

  1. Ultrasonic assisted hot metal powder compaction.

    Science.gov (United States)

    Abedini, Rezvan; Abdullah, Amir; Alizadeh, Yunes

    2017-09-01

    Hot pressing of metal powders is used in production of parts with similar properties to wrought materials. During hot pressing processes, particle rearrangement, plastic deformation, creep, and diffusion are of the most effective powder densification mechanisms. Applying ultrasonic vibration is thought to result in great rates of densification and therefore higher efficiency of the process is expected. This paper deals with the effects of power ultrasonic on the densification of AA1100 aluminum powder under constant applied stress. The effects of particle size and process temperature on the densification behavior are discussed. The results show that applying ultrasonic vibration leads to an improved homogeneity and a higher relative density. Also, it is found that the effect of ultrasonic vibration is greater for finer particles. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. Hand Gesture Recognition Using Ultrasonic Waves

    KAUST Repository

    AlSharif, Mohammed Hussain

    2016-01-01

    estimation of the moving hand and received signal strength (RSS). These two factors are estimated using two simple methods; channel impulse response (CIR) and cross correlation (CC) of the reflected ultrasonic signal from the gesturing hand. A customized

  3. Ultrasonic Morphological Analyzers for Breast Cancer Diagnosis

    National Research Council Canada - National Science Library

    Lizzi, Frederic

    1999-01-01

    The goal of this research is to improve ultrasonic classification of breast lesions and guide decisions regarding biopsy requirements, especially for small lesions and those in young, dense breasts...

  4. Rail inspection using noncontact laser ultrasonics

    International Nuclear Information System (INIS)

    Kim, Nak Hyeon; Sohn, Hoon; Han, Soon Woo

    2012-01-01

    In this study, a noncontact laser ultrasonic system is proposed for rail defect detection. An Nd Yag pulse laser is used for generation of ultrasonic waves, and the corresponding ultrasonic responses are measured by a laser Doppler vibrometer. For the detection of rail surface damages, the shape of the excitation laser beam is transformed into a line. On the other hand, a point source laser beam is used for the inspection of defects inside a rail head. Then, the interactions of propagating ultrasonic waves with defects are examined using actual rail specimens. Amplitude attenuation was mainly observed for a surface crack, and reflections were most noticeable from an internal damage. Finally, opportunities and challenges associated with real time rail inspection from a high speed train are discussed

  5. Nondestructive control of materials by ultrasonic tests

    International Nuclear Information System (INIS)

    Mercier, Noelle.

    1974-01-01

    A bibliographic study of nondestructive control methods of solids by ultrasonic tests, and of the ultrasonic emission of a transducer of finite dimension, is first presented. The principle of two of these methods is verified experimentally; they should permit the measurement of various physical parameters of solids, and the detection of local inhomogeneities. The first method calls upon the analysis of the ultrasonic signal (amplitude and phase), after it has crossed a constant thickness of a metallic specimen. This analysis reveals variations of attenuation and of ultrasonic propagation velocity within the specimen. A good spatial resolution is obtained by using 1mm-diameter probes. The second method leads, thanks to a test rig equipped with broad frequency band electrostatic transducers, to the knowledge of the attenuation law of the specimens as a function of frequency (present range: 5 to 15MHz); from this a classification of these specimens as regards their granulometry is deduced [fr

  6. Ultrasonic testing of materials at level 2

    International Nuclear Information System (INIS)

    1988-06-01

    Ultrasonic inspection is a nondestructive method in which high frequency sound waves are introduced into the material being inspected. Ultrasonic testing has a superior penetrating power to radiography and can detect flaws deep in the test specimen (say up to about 6 to 7 meters of steel). It is quite sensitive to small flaws and allows the precise determination of the location and size of the flaws. Basic ultrasonic test methods such as the through transmission method and the resonance method, sensors and testing techniques are described. Pulse echo type flaw detectors and their applications for inspection of welds are surveyed. Ultrasonic standards, calibration of the equipment and evaluation methods are presented. Examples of practical applications in welding, casting and forging processes are given. Figs and tabs

  7. Improvement of Ultrasonic Distance Measuring System

    Directory of Open Access Journals (Sweden)

    Jiang Yu

    2018-01-01

    Full Text Available This paper mainly introduces a kind of ultrasonic distance measuring system with AT89C51 single chip as the core component. The paper expounds the principle of ultrasonic sensor and ultrasonic ranging, hardware circuit and software program, and the results of experiment and analysis.The hardware circuit based on SCM, the software design adopts the advanced microcontroller programming language.The amplitude of the received signal and the time of ultrasonic propagation are regulated by closed loop control. [1,2]The double closed loop control technology for amplitude and time improves the measuring accuracy of the instrument. The experimental results show that greatly improves the measurement accuracy of the system.

  8. DoS detection in IEEE 802.11 with the presence of hidden nodes

    Directory of Open Access Journals (Sweden)

    Joseph Soryal

    2014-07-01

    Full Text Available The paper presents a novel technique to detect Denial of Service (DoS attacks applied by misbehaving nodes in wireless networks with the presence of hidden nodes employing the widely used IEEE 802.11 Distributed Coordination Function (DCF protocols described in the IEEE standard [1]. Attacker nodes alter the IEEE 802.11 DCF firmware to illicitly capture the channel via elevating the probability of the average number of packets transmitted successfully using up the bandwidth share of the innocent nodes that follow the protocol standards. We obtained the theoretical network throughput by solving two-dimensional Markov Chain model as described by Bianchi [2], and Liu and Saadawi [3] to determine the channel capacity. We validated the results obtained via the theoretical computations with the results obtained by OPNET simulator [4] to define the baseline for the average attainable throughput in the channel under standard conditions where all nodes follow the standards. The main goal of the DoS attacker is to prevent the innocent nodes from accessing the channel and by capturing the channel’s bandwidth. In addition, the attacker strives to appear as an innocent node that follows the standards. The protocol resides in every node to enable each node to police other nodes in its immediate wireless coverage area. All innocent nodes are able to detect and identify the DoS attacker in its wireless coverage area. We applied the protocol to two Physical Layer technologies: Direct Sequence Spread Spectrum (DSSS and Frequency Hopping Spread Spectrum (FHSS and the results are presented to validate the algorithm.

  9. DoS detection in IEEE 802.11 with the presence of hidden nodes.

    Science.gov (United States)

    Soryal, Joseph; Liu, Xijie; Saadawi, Tarek

    2014-07-01

    The paper presents a novel technique to detect Denial of Service (DoS) attacks applied by misbehaving nodes in wireless networks with the presence of hidden nodes employing the widely used IEEE 802.11 Distributed Coordination Function (DCF) protocols described in the IEEE standard [1]. Attacker nodes alter the IEEE 802.11 DCF firmware to illicitly capture the channel via elevating the probability of the average number of packets transmitted successfully using up the bandwidth share of the innocent nodes that follow the protocol standards. We obtained the theoretical network throughput by solving two-dimensional Markov Chain model as described by Bianchi [2], and Liu and Saadawi [3] to determine the channel capacity. We validated the results obtained via the theoretical computations with the results obtained by OPNET simulator [4] to define the baseline for the average attainable throughput in the channel under standard conditions where all nodes follow the standards. The main goal of the DoS attacker is to prevent the innocent nodes from accessing the channel and by capturing the channel's bandwidth. In addition, the attacker strives to appear as an innocent node that follows the standards. The protocol resides in every node to enable each node to police other nodes in its immediate wireless coverage area. All innocent nodes are able to detect and identify the DoS attacker in its wireless coverage area. We applied the protocol to two Physical Layer technologies: Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS) and the results are presented to validate the algorithm.

  10. Ultrasonic Generation and Optimization for EMAT

    International Nuclear Information System (INIS)

    Jian, X.; Dixon, Steve; Edwards, Rachel S.

    2005-01-01

    A model for transient ultrasonic wave generation by EMATs in non-magnetic metals is presented. It combines analytical solutions currently available and FEM to calculate ultrasonic bulk and Rayleigh waves generated by the EMAT. Analytical solutions are used as they can be calculated quickly on a standard mathematical computer package. Calculations agree well with the experimental measurement. The model can be used to optimize EMAT design, and has explained some of the results from our previous published measurements

  11. Extrinsic Fabry-Perot ultrasonic detector

    Science.gov (United States)

    Kidwell, J. J.; Berthold, John W., III

    1996-10-01

    We characterized the performance of a commercial fiber optic extrinsic Fabry-Perot interferometer for use as an ultrasonic sensor, and compared the performance with a standard lead zirconate titanate (PZT) detector. The interferometer was unstabilized. The results showed that the fiber sensor was about 12 times less sensitive than the PZT detector. Ultrasonic frequency response near 100 kHz was demonstrated. We describe the design of the fiber sensor, the details of the tests performed, and potential applications.

  12. An advanced system for automated ultrasonic testing

    International Nuclear Information System (INIS)

    Dressler, K.

    1989-01-01

    As the main component of the AUP system, an ALOK ultrasonic unit has been chosen as it allows for testing of large component areas both search for defects and description of defect geometries. All data required for fault analysis can be obtained by one measuring run. For inspection of primary circuit components in nuclear power stations, the manipulator control and the ultrasonic probe are installed behind the first sufficient shielding. (orig./HP) [de

  13. Ultrasonic flow measurements for irrigation process monitoring

    Science.gov (United States)

    Ziani, Elmostafa; Bennouna, Mustapha; Boissier, Raymond

    2004-02-01

    This paper presents the state of the art of the general principle of liquid flow measurements by ultrasonic method, and problems of flow measurements. We present an ultrasonic flowmeter designed according to smart sensors concept, for the measurement of irrigation water flowing through pipelines or open channels, using the ultrasonic transit time approach. The new flowmeter works on the principle of measuring time delay differences between sound pulses transmitted upstream and downstream in the flowing liquid. The speed of sound in the flowing medium is eliminated as a variable because the flowrate calculations are based on the reciprocals of the transmission times. The transit time difference is digitally measured by means of a suitable, microprocessor controlled logic. This type of ultrasonic flowmeter will be widely used in industry and water management, it is well studied in this work, followed by some experimental results. For pressurized channels, we use one pair of ultrasonic transducer arranged in proper positions and directions of the pipe, in this case, to determine the liquid velocity, a real time on-line analysis taking account the geometries of the hydraulic system, is applied to the obtained ultrasonic data. In the open channels, we use a single or two pairs of ultrasonic emitter-receiver according to the desired performances. Finally, the goals of this work consist in integrating the smart sensor into irrigation systems monitoring in order to evaluate potential advantages and demonstrate their performance, on the other hand, to understand and use ultrasonic approach for determining flow characteristics and improving flow measurements by reducing errors caused by disturbances of the flow profiles.

  14. Fundamentals and Applications of Ultrasonic Waves

    CERN Document Server

    Cheeke, J David N

    2012-01-01

    Designed specifically for newcomers to the field, this fully updated second edition begins with fundamentals and quickly advances beyond general wave concepts into an in-depth treatment of ultrasonic waves in isotropic media. Focusing on the physics of acoustic waves, their propagation, technology, and applications, this accessible overview of ultrasonics includes accounts of viscoelasticity and multiple scattering. It examines new technologies, including atomic force acoustic microscopy, lasers, micro-acoustics, and nanotechnology. In addition, it highlights both direct and indirect applicati

  15. Longitudinal ultrasonic waves dispersion in bars

    International Nuclear Information System (INIS)

    Suarez Antola, R.

    2001-01-01

    The exhibition intends to review some aspects of the propagation of the longitudinal ultrasonic pulses shortly in bars of traverse section uniform.Aspects they are part of the denominated geometric dispersion of the pulses.This phenomenon It can present like an additional complication in the ultrasonic essay of low frequency of thin pieces in structures and machines but takes place former ex professed in some applications of the wave guides been accustomed to in the prosecution of signs

  16. A Novel Energy Saving Algorithm with Frame Response Delay Constraint in IEEE 802.16e

    Science.gov (United States)

    Nga, Dinh Thi Thuy; Kim, Mingon; Kang, Minho

    Sleep-mode operation of a Mobile Subscriber Station (MSS) in IEEE 802.16e effectively saves energy consumption; however, it induces frame response delay. In this letter, we propose an algorithm to quickly find the optimal value of the final sleep interval in sleep-mode in order to minimize energy consumption with respect to a given frame response delay constraint. The validations of our proposed algorithm through analytical results and simulation results suggest that our algorithm provide a potential guidance to energy saving.

  17. A Secure Simplification of the PKMv2 Protocol in IEEE 802.16e-2005

    DEFF Research Database (Denmark)

    Yuksel, Ender; Nielson, Hanne Riis; Nielsen, Christoffer Rosenkilde

    2007-01-01

    Static analysis is successfully used for automatically validating security properties of classical cryptographic protocols. In this paper, we shall employ the same technique to a modern security protocol for wireless networks, namely the latest version of the Privacy and Key Management protocol...... for IEEE 802.16e, PKMv2. This protocol seems to have an exaggerated mixture of security features. Thus, we iteratively investigate which components are necessary for upholding the security properties and which can be omitted safely. This approach is based on the LySa process calculus and employs...

  18. An IEEE 802.3 Compatible Real Time Medium Access Control with Length-based Priority

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A new medium access control method is proposed over the predominant Ethernet broadcast channel. Taking advantages of intrinsic variable length characteristic of standard Ethernet frame, message-oriented dynamic priority mechanism is established. Prioritized medium access control operates under a so-called block mode in event of collisions.High priority messages have a chance to preempt block status incurred by low priority ones. By this means, the new MAC provides a conditional deterministic real time performance beyond a statistical one. Experiments demonstrate effectiveness and attractiveness of the proposed scheme. Moreover, this new MAC is completely compatible with IEEE802.3.

  19. 2012 Special NSREC Issue of the IEEE Transactions on Nuclear Science Comments by the Editors

    Science.gov (United States)

    Schwank, Jim; Brown, Dennis; Girard, Sylvain; Gouker, Pascale; Gerardin, Simone; Quinn, Heather; Barnaby, Hugh

    2012-12-01

    The December 2012 special issue of the IEEE Transactions on Nuclear Science contains selected papers from the 49th annual IEEE International Nuclear and Space Radiation Effects Conference (NSREC) held July 16-20, 2012, in Miami, Florida USA. 95 papers presented at the 2012 NSREC were submitted for consideration for this year’s special issue. Those papers that appear in this special issue were able to successfully complete the review process before the deadline for the December issue. A few additional papers may appear in subsequent issues of the TRANSACTIONS. This publication is the premier archival journal for research on space and nuclear radiation effects in materials, devices, circuits, and systems. This distinction is the direct result of the conscientious efforts of both the authors, who present and document their work, and the reviewers, who selflessly volunteer their time and talent to help review the manuscripts. Each paper in this journal has been reviewed by experts selected by the editors for their expertise and knowledge of the particular subject areas. The peer review process for a typical technical journal generally takes six months to one year to complete. To publish this special issue of the IEEE Transactions on Nuclear Science (in December), the review process, from initial submission to final form, must be completed in about 10 weeks. Because of the short schedule, both the authors and reviewers are required to respond very quickly. The reviewers listed on the following pages contributed vitally to this quick-turn review process.We would like to express our sincere appreciation to each of them for accepting this difficult, but critical role in the process. To provide consistent reviews of papers throughout the year, the IEEE Transactions on Nuclear Science relies on a year-round editorial board that manages reviews for submissions throughout the year to the TRANSACTIONS in the area of radiation effects. The review process is managed by a Senior

  20. A time-based admission control mechanism for IEEE 802.11 ad Hoc networks

    OpenAIRE

    Costa, Luís Henrique M. K.; Cerveira, Carlos Rodrigo

    2006-01-01

    This paper presents a time-based admission control mechanism (TAC) for IEEE 802.11 ad hoc networks. The proposed mechanism was adapted to the QoS AODV routing protocol, which takes the quality of service requirements of the data flow into account in the route discovery process. TAC-AODV estimates the idle time of the physical medium based on the frames listened. The incoming traffic is admitted according to the offered load as well as the intra-flow interference, calculated based on the numbe...

  1. 4th IEEE/ACIS International Conference on Computer and Information Science

    CERN Document Server

    2016-01-01

    This edited book presents scientific results of the 14th IEEE/ACIS International Conference on Computer and Information Science (ICIS 2015) which was held on June 28 – July 1, 2015 in Las Vegas, USA. The aim of this conference was to bring together researchers and scientists, businessmen and entrepreneurs, teachers, engineers, computer users, and students to discuss the numerous fields of computer science and to share their experiences and exchange new ideas and information in a meaningful way. Research results about all aspects (theory, applications and tools) of computer and information science, and to discuss the practical challenges encountered along the way and the solutions adopted to solve them.

  2. Impacto de mecanismos de seguridad en sensores IEEE 802.15.4

    OpenAIRE

    Tripp Barba, Carolina; Casademont Serra, Jordi

    2009-01-01

    En la actualidad son muchos los mecanismos de seguridad que el estándar IEEE 802.15.4 permite a las redes inalámbricas de sensores [1] Dicho estándar define las especificaciones de la Capa de Acceso al Medio y la Capa Física de los dispositivos inalámbricos de área personal. La última revisión corresponde al 2006. Dichas revisiones y actualizaciones son hechas por el grupo de trabajo 802.15. Sin embargo estos mecanismos consumen recursos como memoria y batería, que son...

  3. Low-frequency electrical dosimetry: research agenda of the IEEE International Committee on Electromagnetic Safety.

    Science.gov (United States)

    Reilly, J Patrick; Hirata, Akimasa

    2016-06-21

    This article treats unsettled issues in the use of numerical models of electrical dosimetry as applied to international limits on human exposure to low-frequency (typically  IEEE-ICES (International Committee on Electromagnetic Safety) Technical Committee 95. The paper discusses 25 issues needing attention, fitting into three general categories: induction models; electrostimulation models; and human exposure limits. Of these, 9 were voted as 'high priority' by members of Subcommittee 6. The list is presented as a research agenda for refinements in numerical modeling with applications to human exposure limits. It is likely that such issues are also important in medical and electrical product safety design applications.

  4. Connectivity-Based Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs

    Directory of Open Access Journals (Sweden)

    Woo-Yong Choi

    2009-01-01

    Full Text Available We propose the efficient reliable multicast MAC protocol based on the connectivity information among the recipients. Enhancing the BMMM (Batch Mode Multicast MAC protocol, the reliable multicast MAC protocol significantly reduces the RAK (Request for ACK frame transmissions in a reasonable computational time and enhances the MAC performance. By the analytical performance analysis, the throughputs of the BMMM protocol and our proposed MAC protocol are derived. Numerical examples show that our proposed MAC protocol increases the reliable multicast MAC performance for IEEE 802.11 wireless LANs.

  5. Impact of cell load on 5GHz IEEE 802.11 WLAN

    OpenAIRE

    Abu-Tair, Mamoun; Bhatti, Saleem Noel

    2017-01-01

    We have conducted an empirical study of the latest 5GHz IEEE 802.11 wireless LAN (WLAN) variants of 802.11n (5GHz) and 802.11ac (Wave 1), under different cell load conditions. We have considered typical configurations of both protocols on a Linux testbed. Under light load,there is no clear difference between 802.11n and 802.11ac in terms of performance and energy consumption. However, in some cases of high cell load, we have found that there may be a small advantage with 802.11ac. Overall, we...

  6. Distributed Fair Access Point Selection for Multi-Rate IEEE 802.11 WLANs

    Science.gov (United States)

    Gong, Huazhi; Nahm, Kitae; Kim, Jongwon

    In IEEE 802.11 networks, the access point (AP) selection based on the strongest signal strength often results in the extremely unfair bandwidth allocation among mobile users (MUs). In this paper, we propose a distributed AP selection algorithm to achieve a fair bandwidth allocation for MUs. The proposed algorithm gradually balances the AP loads based on max-min fairness for the available multiple bit rate choices in a distributed manner. We analyze the stability and overhead of the proposed algorithm, and show the improvement of the fairness via computer simulation.

  7. Rate Adaptation Based on Collision Probability for IEEE 802.11 WLANs

    Science.gov (United States)

    Kim, Taejoon; Lim, Jong-Tae

    Nowadays IEEE 802.11 wireless local area networks (WLANs) support multiple transmission rates. To achieve the best performance, transmitting stations adopt the various forms of automatic rate fallback (ARF). However, ARF suffers from severe performance degradation as the number of transmitting stations increases. In this paper, we propose a new rate adaptation scheme which adjusts the ARF's up/down threshold according to the channel contention level. Simulation result shows that the proposed scheme achieves fairly good performance compared with the existing schemes.

  8. Adaptive rate selection scheme for video transmission to resolve IEEE 802.11 performance anomaly

    Science.gov (United States)

    Tang, Guijin; Zhu, Xiuchang

    2011-10-01

    Multi-rate transmission may lead to performance anomaly in an IEEE 802.11 network. It will decrease the throughputs of all the higher rate stations. This paper proposes an adaptive rate selection scheme for video service when performance anomaly occurs. Considering that video has the characteristic of tolerance to packet loss, we actively drop several packets so as to select the rates as high as possible for transmitting packets. Experiment shows our algorithm can decrease the delay and jitter of video, and improve the system throughput as well.

  9. A Fair Cooperative MAC Protocol in IEEE 802.11 WLAN

    Directory of Open Access Journals (Sweden)

    Seyed Davoud Mousavi

    2018-05-01

    Full Text Available Cooperative communication techniques have recently enabled wireless technologies to overcome their challenges. The main objective of these techniques is to improve resource allocation. In this paper, we propose a new protocol in medium access control (MAC of the IEEE 802.11 standard. In our new protocol, which is called Fair Cooperative MAC (FC-MAC, every relay node participates in cooperation proportionally to its provided cooperation gain. This technique improves network resource allocation by exploiting the potential capacity of all relay candidates. Simulation results demonstrate that the FC-MAC protocol presents better performance in terms of throughput, fairness, and network lifetime.

  10. Latency and Jitter Analysis for IEEE 802.11e Wireless LANs

    Directory of Open Access Journals (Sweden)

    Sungkwan Youm

    2013-01-01

    Full Text Available This paper presents a numerical analysis of latency and jitter for IEEE 802.11e wireless local area networks (WLANs in a saturation condition, by using a Markov model. We use this model to explicate how the enhanced distributed coordination function (EDCF differentiates classes of service and to characterize the probability distribution of the medium access control (MAC layer packet latency and jitter, on which the quality of the voice over Internet protocol (VoIP calls is dependent. From the proposed analytic model, we can estimate the available number of nodes determining the system performance, in order to satisfy user demands on the latency and jitter.

  11. Planning of Efficient Wireless Access with IEEE 802.16 for Connecting Home Network to the Internet

    Directory of Open Access Journals (Sweden)

    Pichet Ritthisoonthorn

    2010-01-01

    Full Text Available The emergence of IEEE802.16 wireless standard technology (WiMAX has significantly increased the choice to operators for the provisioning of wireless broadband access network. WiMAX is being deployed to compliment with xDSL in underserved or lack of the broadband network area, in both developed and developing countries. Many incumbent operators in developing countries are considering the deployment of WiMAX as part of their broadband access strategy. This paper presents an efficient and simple method for planning of broadband fixed wireless access (BFWA with IEEE802.16 standard to support home connection to Internet. The study formulates the framework for planning both coverage and capacity designs. The relationship between coverage area and access rate from subscriber in each environment area is presented. The study also presents the throughput and channel capacity of IEEE802.16 in different access rates. An extensive analysis is performed and the results are applied to the real case study to demonstrate the practicality of using IEEE 802.16 for connecting home to Internet. Using empirical data and original subscriber traffic from measurement, it is shown that the BFWA with IEEE802.16 standard is a capacity limited system. The capacity of IEEE802.16 is related to different factors including frequency bandwidth, spectrum allocation, estimation of traffic per subscriber, and choice of adaptive modulation from subscriber terminal. The wireless access methods and procedures evolved in this research work and set out in this paper are shown to be well suited for planning BFWA system based on IEEE802.16 which supports broadband home to Internet connections.

  12. Ultrasonic Characterization of Superhard Material: Osmium Diboride

    International Nuclear Information System (INIS)

    Yadawa, P K

    2012-01-01

    Higher order elastic constants have been calculated in hexagonal structured superhard material OsB 2 at room temperature following the interaction potential model. The temperature variation of the ultrasonic velocities is evaluated along different angles with unique axis of the crystal using the second order elastic constants. The ultrasonic velocity decreases with the temperature along particular orientation with the unique axis. Temperature variation of the thermal relaxation time and Debye average velocities are also calculated along the same orientation. The temperature dependency of the ultrasonic properties is discussed in correlation with elastic, thermal and electrical properties. It has been found that the thermal conductivity is the main contributor to the behaviour of ultrasonic attenuation as a function of temperature and the responsible cause of attenuation is phonon-phonon interaction. The mechanical properties of OsB 2 at low temperature are better than at high temperature, because at low temperature it has low ultrasonic velocity and ultrasonic attenuation. Superhard material OsB 2 has many industrial applications, such as abrasives, cutting tools and hard coatings.

  13. Trans-sphenoidal excision of craniopharyngiomas.

    Directory of Open Access Journals (Sweden)

    Nagpal R

    1991-04-01

    Full Text Available Craniopharyngiomas have been by and large excised by the transcranial route. Since 1982, 11 patients have been operated by the traus-sphensidal route in the department. The clinical features with which they were presented, diagnostic investigations, details of surgical procedures and follow-up analysis is being presented here. A retrospective study of radiological investigation was done to determine the features that help decide the choice of surgical approach to these lesions. Only lesions that were primarily intrasellar, cystic and those that expanded the sella could be treated by the trans-sphenoidal route. Associated suprasellar extensions could also be removed. Predominantly calcified or firm, fleshy tumours lent themselves poorly to removal by the trans-sphenoidal route.

  14. Trans Fat Bans and Human Freedom

    Science.gov (United States)

    Resnik, David

    2014-01-01

    A growing body of evidence has linked consumption of trans fatty acids to cardiovascular disease. To promote public health, numerous state and local governments in the United States have banned the use of artificial trans fats in restaurant foods, and additional bans may follow. Although these policies may have a positive impact on human health, they open the door to excessive government control over food, which could restrict dietary choices, interfere with cultural, ethnic, and religious traditions, and exacerbate socioeconomic inequalities. These slippery slope concerns cannot be dismissed as far-fetched, because the social and political pressures are place to induce additional food regulations. To protect human freedom and other values, policies that significantly restrict food choices, such as bans on types of food, should be adopted only when they are supported by substantial scientific evidence, and when policies that impose fewer restrictions on freedom, such as educational campaigns and product labeling, are likely to be ineffective. PMID:20229412

  15. Introduction to Trans Australia Airlines CRM training

    Science.gov (United States)

    Davidson, Jim

    1987-01-01

    Trans Australia believes that its excellent accident rate record is due to a number of factors. It has a good group of standard operating procedures, and its crews are pretty well self-disciplined and adhere to those procedures. But the other thing that it believes is a factor in its safety record is that perhaps it is also due to its preparedness to be innovative, to keep up with what is going on in the rest of the world and, if it looks to have value, then to be amongst the first to try it out. Trans Australia commenced a program similar to Line Oriented Flight Training (LOFT) fairly early in 1979--that being its first windshear program-- which leads to why they are doing a course of resource management training, which we have chosen to call Aircrew Team Management (ATM). This course is detailed in another presentation.

  16. Siegel discs via trans-quasiconformal surgery

    DEFF Research Database (Denmark)

    Petersen, Carsten Lunde

    2014-01-01

    kompleksstruktur kan integreres, det vil sige definerer en kompleksstruktur. I denne komplekse struktur er den nye afbildning holomorf og har en Siegel disk. Der findes imidlertid masser af tilfælde hvor dette ikke lader sig gøre, men hvor man istedet kan finde en trans-kvasikonform udvidelse til enheds-disken af...... mængde af rotationstal med fuldt mål på cirklen har konjugationen en trans-kvasi-konform udvidelse til disken. Dette er et skridt i beviset for at for næsten alle (i Lebeguemåls forstand) rotations tal, er randen af Siegel-disken for et kvadratisk polynomium med en Siegel disk med et sådant rotationstal...

  17. Remediation of Diesel Fuel Contaminated Sandy Soil using Ultrasonic Waves

    Directory of Open Access Journals (Sweden)

    Wulandari P.S.

    2010-01-01

    Full Text Available Ultrasonic cleaning has been used in industry for some time, but the application of ultrasonic cleaning in contaminated soil is just recently received considerable attention, it is a very new technique, especially in Indonesia. An ultrasonic cleaner works mostly by energy released from the collapse of millions of microscopic cavitations near the dirty surface. This paper investigates the use of ultrasonic wave to enhance remediation of diesel fuel contaminated sandy soil considering the ultrasonic power, soil particle size, soil density, water flow rate, and duration of ultrasonic waves application.

  18. Analysis of Trans Fat in Edible Oils with Cooking Process

    Science.gov (United States)

    Song, Juhee; Park, Joohyeok; Jung, Jinyeong; Lee, Chankyu; Gim, Seo Yeoung; Ka, HyeJung; Yi, BoRa; Kim, Mi-Ja; Kim, Cho-il

    2015-01-01

    Trans fat is a unsaturated fatty acid with trans configuration and separated double bonds. Analytical methods have been introduced to analyze trans fat content in foods including infrared (IR) spectroscopy, gas chromatography (GC), Fourier transform-infrared (FT-IR) spectroscopy, reverses-phase silver ion high performance liquid chromatography, and silver nitrate thin layer chromatography. Currently, FT-IR spectroscopy and GC are mostly used methods. Trans fat content in 6 vegetable oils were analyzed and processing effects including baking, stir-frying, pan-frying, and frying on the formation of trans fat in corn oil was evaluated by GC. Among tested vegetable oils, corn oil has 0.25 g trans fat/100 g, whereas other oils including rapeseed, soybean, olive, perilla, and sesame oils did not have detectable amount of trans fat content. Among cooking methods, stir-frying increased trans fat in corn oil whereas baking, pan-frying, and frying procedures did not make changes in trans fat content compared to untreated corn oils. However, the trans fat content was so low and food label can be declared as ‘0’ trans based on the regulation of Ministry of Food ad Drug Safety (MFDS) (edible oil). PMID:26483890

  19. Trans-triquetral Perilunate fracture dislocation

    OpenAIRE

    John-Henry Rhind; Abhinav Gulihar; Andrew Smith

    2018-01-01

    Perilunate dislocations and perilunate fracture dislocations are rare and serious injuries. Perilunate dislocations represent less than 10% of all carpal injuries of which 61% represent transcaphoid fractures. Because of their rarity, up to 25% of perilunate dislocations are initially missed on first assessment. We present the case of a 66-year-old-gentleman who sustained an isolated trans-triquetral perilunate fracture dislocation while walking his dog. This was diagnosed in the emergency de...

  20. A strategy for implementation of experience based seismic equipment qualification in IEEE and ASME industry standards

    International Nuclear Information System (INIS)

    Adams, T.M.

    1996-01-01

    In the past 20 years, extensive data on the performance of mechanical and electric equipment during actual strong motion earthquakes and seismic qualification tests has been accumulated. Recognizing that an experience based approach provides a technically sound and cost effective method for the seismic qualification of some or certain equipment, the IEEE Nuclear Power Engineering Committee and the ASME Committee on Qualification of Mechanical Equipment established a Special Working Group to investigate the incorporation of experienced based methods into the industry consensus codes and standards currently used in the seismic qualification of Seismic Category Nuclear Power Plant equipment. This paper presents the strategy (course of action) which was developed by the Special Working Group for meeting this objective of incorporation of experience based seismic qualification standards used in the design and seismic qualification of seismic category nuclear power plant equipment. This strategy was recommended to both chartering organizations, the IEEE Nuclear Power Engineering Committee and the ASME Committee on Qualification of Mechanical Equipment for their consideration and implementation. The status of the review and implementation of the Special Working Group's recommended strategy by the sponsoring organization is also discussed

  1. 2008 Special NSREC Issue of the IEEE Transactions on Nuclear Science Comments by the Editors

    Science.gov (United States)

    Schwank, Jim; Buchner, Steve; Marshall, Paul; Duzellier, Sophie; Brown, Dennis; Poivey, Christian; Pease, Ron

    2008-12-01

    The December 2008 special issue of the IEEE Transactions on Nuclear Science contains selected papers from the 45th annual IEEE International Nuclear and Space Radiation Effects Conference (NSREC) held in Tucson, Arizona, July 14 - 18, 2008. Over 115 papers presented at the 2008 NSREC were submitted for consideration for this year's special issue. Those papers that appear in this special issue were able to successfully complete the review process before the deadline for the December issue. A few additional papers may appear in subsequent issues of the TRANSACTIONS. This publication is the premier archival journal for research on space and nuclear radiation effects in materials, devices, circuits, and systems. This distinction is the direct result of the conscientious efforts of both the authors, who present and document their work, and the reviewers, who selflessly volunteer their time and talent to help review the manuscripts. Each paper in this journal has been reviewed by experts selected by the editors for their expertise and knowledge of the particular subject areas.

  2. BOB-RED queue management for IEEE 802.15.4 wireless sensor networks

    Directory of Open Access Journals (Sweden)

    Wu Jean-Lien

    2011-01-01

    Full Text Available Abstract Multimedia services over resource constrained wireless sensor networks (WSNs face a performance bottleneck issue from the gateway node to the sink node. Therefore, the queue management at the gateway node is crucial for diversified messages conveyed from the front nodes to the sink node. In this article, beacon order-based random early detection (BOB-RED queue management is proposed. BOB-RED is a dynamic adaptation scheme based on adjusting beacon interval and superframe duration in the IEEE 802.15.4 MAC superframe accompanied with RED queue management scheme to increase the transmission efficiency of multimedia over WSNs. We focus on the performance improvement upon different traffic loads over WSNs. Evaluation metrics include end-to-end delay, packet delivery ratio, and energy consumption in IEEE 802.15.4 beacon enabled mode. Simulation results show that BOB-RED can effectively decrease end-to-end delay and energy consumption compared to the DropTail scheme.

  3. Throughput analysis of the IEEE 802.4 token bus standard under heavy load

    Science.gov (United States)

    Pang, Joseph; Tobagi, Fouad

    1987-01-01

    It has become clear in the last few years that there is a trend towards integrated digital services. Parallel to the development of public Integrated Services Digital Network (ISDN) is service integration in the local area (e.g., a campus, a building, an aircraft). The types of services to be integrated depend very much on the specific local environment. However, applications tend to generate data traffic belonging to one of two classes. According to IEEE 802.4 terminology, the first major class of traffic is termed synchronous, such as packetized voice and data generated from other applications with real-time constraints, and the second class is called asynchronous which includes most computer data traffic such as file transfer or facsimile. The IEEE 802.4 token bus protocol which was designed to support both synchronous and asynchronous traffic is examined. The protocol is basically a timer-controlled token bus access scheme. By a suitable choice of the design parameters, it can be shown that access delay is bounded for synchronous traffic. As well, the bandwidth allocated to asynchronous traffic can be controlled. A throughput analysis of the protocol under heavy load with constant channel occupation of synchronous traffic and constant token-passing times is presented.

  4. Real-Time-Simulation of IEEE-5-Bus Network on OPAL-RT-OP4510 Simulator

    Science.gov (United States)

    Atul Bhandakkar, Anjali; Mathew, Lini, Dr.

    2018-03-01

    The Real-Time Simulator tools have high computing technologies, improved performance. They are widely used for design and improvement of electrical systems. The advancement of the software tools like MATLAB/SIMULINK with its Real-Time Workshop (RTW) and Real-Time Windows Target (RTWT), real-time simulators are used extensively in many engineering fields, such as industry, education, and research institutions. OPAL-RT-OP4510 is a Real-Time Simulator which is used in both industry and academia. In this paper, the real-time simulation of IEEE-5-Bus network is carried out by means of OPAL-RT-OP4510 with CRO and other hardware. The performance of the network is observed with the introduction of fault at various locations. The waveforms of voltage, current, active and reactive power are observed in the MATLAB simulation environment and on the CRO. Also, Load Flow Analysis (LFA) of IEEE-5-Bus network is computed using MATLAB/Simulink power-gui load flow tool.

  5. Improving Energy Efficiency in Idle Listening of IEEE 802.11 WLANs

    Directory of Open Access Journals (Sweden)

    Muhammad Adnan

    2016-01-01

    Full Text Available This paper aims to improve energy efficiency of IEEE 802.11 wireless local area networks (WLANs by effectively dealing with idle listening (IL, which is required for channel sensing and is unavoidable in a contention-based channel access mechanism. Firstly, we show that IL is a dominant source of energy drain in WLANs and it cannot be effectively alleviated by the power saving mechanism proposed in the IEEE 802.11 standard. To solve this problem, we propose an energy-efficient mechanism that combines three schemes in a systematic way: downclocking, frame aggregation, and contention window adjustment. The downclocking scheme lets a station remain in a semisleep state when overhearing frames destined to neighbor stations, whereby the station consumes the minimal energy without impairing channel access capability. As well as decreasing the channel access overhead, the frame aggregation scheme prolongs the period of semisleep time. Moreover, by controlling the size of contention window based on the number of stations, the proposed mechanism decreases unnecessary IL time due to collision and retransmission. By deriving an analysis model and performing extensive simulations, we confirm that the proposed mechanism significantly improves the energy efficiency and throughput, by up to 2.8 and 1.8 times, respectively, compared to the conventional power saving mechanisms.

  6. A Green Media Access Method for IEEE 802.15.6 Wireless Body Area Network.

    Science.gov (United States)

    Jacob, Anil K; Jacob, Lillykutty

    2017-09-30

    It is of utmost importance to conserve battery energy to the maximum possible extent in WBAN nodes while collecting and transferring medical data. The IEEE 802.15.6 WBAN standard does not specify any method to conserve energy. This paper focuses on a method to conserve energy in IEEE 802.15.6 WBAN nodes when using CSMA/CA, while simultaneously restricting data delivery delay to the required value as specified in medical applications. The technique is to allow the nodes to sleep all the times except for receiving beacons and for transmitting data frames whenever a data frame enters an empty buffer. The energy consumed by the nodes and the average latency of data frame for periodical arrival of data are found out analytically. The analytical results are validated and also the proposed method is compared with other energy conserving schemes, using Castalia simulation studies. The proposed method shows superior performance in both device lifetime and latency of emergency medical data.

  7. Predictable and reliable ECG monitoring over IEEE 802.11 WLANs within a hospital.

    Science.gov (United States)

    Park, Juyoung; Kang, Kyungtae

    2014-09-01

    Telecardiology provides mobility for patients who require constant electrocardiogram (ECG) monitoring. However, its safety is dependent on the predictability and robustness of data delivery, which must overcome errors in the wireless channel through which the ECG data are transmitted. We report here a framework that can be used to gauge the applicability of IEEE 802.11 wireless local area network (WLAN) technology to ECG monitoring systems in terms of delay constraints and transmission reliability. For this purpose, a medical-grade WLAN architecture achieved predictable delay through the combination of a medium access control mechanism based on the point coordination function provided by IEEE 802.11 and an error control scheme based on Reed-Solomon coding and block interleaving. The size of the jitter buffer needed was determined by this architecture to avoid service dropout caused by buffer underrun, through analysis of variations in transmission delay. Finally, we assessed this architecture in terms of service latency and reliability by modeling the transmission of uncompressed two-lead electrocardiogram data from the MIT-BIH Arrhythmia Database and highlight the applicability of this wireless technology to telecardiology.

  8. Investigating the efficiency of IEEE 802.15.4 for medical monitoring applications.

    Science.gov (United States)

    Pelegris, P; Banitsas, K

    2011-01-01

    Recent advancements in wireless communications technologies bring us one step closer to provide reliable Telecare services as an alternative to patients staying in a hospital mainly for monitoring purposes. In this research we investigate the efficiency of IEEE 802.15.4 in a simple scenario where a patient is being monitored using an ECG and a blood analysis module. This approach binds well with assisted living solutions, by sharing the network infrastructure for both monitoring and control while taking advantage of the low power features of the protocol. Such applications are becoming more and more realistic to implement as IEEE 802.15.4 compatible hardware becomes increasingly available. Our aim is to examine the impact of Beacon and Superframe Order in the medium access delay, dropped packets, end to end delay, average retransmission attempts and consumed power focusing on this bandwidth demanding situation where the network load does not allow low duty cycles, in order to draw some conclusions on the effect that this will have to telemonitoring applications.

  9. Self-Coexistence among IEEE 802.22 Networks: Distributed Allocation of Power and Channel.

    Science.gov (United States)

    Sakin, Sayef Azad; Razzaque, Md Abdur; Hassan, Mohammad Mehedi; Alamri, Atif; Tran, Nguyen H; Fortino, Giancarlo

    2017-12-07

    Ensuring self-coexistence among IEEE 802.22 networks is a challenging problem owing to opportunistic access of incumbent-free radio resources by users in co-located networks. In this study, we propose a fully-distributed non-cooperative approach to ensure self-coexistence in downlink channels of IEEE 802.22 networks. We formulate the self-coexistence problem as a mixed-integer non-linear optimization problem for maximizing the network data rate, which is an NP-hard one. This work explores a sub-optimal solution by dividing the optimization problem into downlink channel allocation and power assignment sub-problems. Considering fairness, quality of service and minimum interference for customer-premises-equipment, we also develop a greedy algorithm for channel allocation and a non-cooperative game-theoretic framework for near-optimal power allocation. The base stations of networks are treated as players in a game, where they try to increase spectrum utilization by controlling power and reaching a Nash equilibrium point. We further develop a utility function for the game to increase the data rate by minimizing the transmission power and, subsequently, the interference from neighboring networks. A theoretical proof of the uniqueness and existence of the Nash equilibrium has been presented. Performance improvements in terms of data-rate with a degree of fairness compared to a cooperative branch-and-bound-based algorithm and a non-cooperative greedy approach have been shown through simulation studies.

  10. Performance analysis of the IEEE 802.16e power management for the initiations of awakening

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    To increase battery life in IEEE 802.16e systems, it is essential to efficiently manage energy in mobile stations. The sleep-mode operation in power management helps to increase the life of a station by saving energy consumption. In power management, there are two important performance metrics: energy consumption and the response delay of awakening medium access control (MAC) service data unit (SDU). While in a base station (BS) initiation of awakening, the two performance metrics should be simultaneously considered, in a mobile subscriber station (MSS) initiation of awakening, the response delay is not considered because it is self-operational. There performance metrics are affected by the minimum sleep interval (Tmin), the maximum sleep interval (Tmax), and the average interarrival time of awakening MAC SDUs (TI) during sleep-mode operation. Therefore, it is imperative to evaluate the two initiations of awakening depending on TI. To reach a fuller understanding of the performance, this paper shows an analytical mode and simulations results for the standard sleep-mode operation in the IEEE 802.16e MAC.

  11. IEEE 1394 CAMERA IMAGING SYSTEM FOR BROOKHAVENS BOOSTER APPLICATION FACILITY BEAM DIAGNOSTICS

    International Nuclear Information System (INIS)

    BROWN, K.A.; FRAK, B.; GASSNER, D.; HOFF, L.; OLSEN, R.H.; SATOGATA, T.; TEPIKIAN, S.

    2002-01-01

    Brookhaven's Booster Applications Facility (BAF) will deliver resonant extracted heavy ion beams from the AGS Booster to short-exposure fixed-target experiments located at the end of the BAF beam line. The facility is designed to deliver a wide range of heavy ion species over a range of intensities from 10 3 to over 10 8 ions/pulse, and over a range of energies from 0.1 to 3.0 GeV/nucleon. With these constraints we have designed instrumentation packages which can deliver the maximum amount of dynamic range at a reasonable cost. Through the use of high quality optics systems and neutral density light filters we will achieve 4 to 5 orders of magnitude in light collection. By using digital IEEE1394 camera systems we are able to eliminate the frame-grabber stage in processing and directly transfer data at maximum rates of 400 Mb/set. In this note we give a detailed description of the system design and discuss the parameters used to develop the system specifications. We will also discuss the IEEE1394 camera software interface and the high-level user interface

  12. An Adaptive Medium Access Parameter Prediction Scheme for IEEE 802.11 Real-Time Applications

    Directory of Open Access Journals (Sweden)

    Estefanía Coronado

    2017-01-01

    Full Text Available Multimedia communications have experienced an unprecedented growth due mainly to the increase in the content quality and the emergence of smart devices. The demand for these contents is tending towards wireless technologies. However, these transmissions are quite sensitive to network delays. Therefore, ensuring an optimum QoS level becomes of great importance. The IEEE 802.11e amendment was released to address the lack of QoS capabilities in the original IEEE 802.11 standard. Accordingly, the Enhanced Distributed Channel Access (EDCA function was introduced, allowing it to differentiate traffic streams through a group of Medium Access Control (MAC parameters. Although EDCA recommends a default configuration for these parameters, it has been proved that it is not optimum in many scenarios. In this work a dynamic prediction scheme for these parameters is presented. This approach ensures an appropriate traffic differentiation while maintaining compatibility with the stations without QoS support. As the APs are the only devices that use this algorithm, no changes are required to current network cards. The results show improvements in both voice and video transmissions, as well as in the QoS level of the network that the proposal achieves with regard to EDCA.

  13. Dynamic Contention Window Control Scheme in IEEE 802.11e EDCA-Based Wireless LANs

    Science.gov (United States)

    Abeysekera, B. A. Hirantha Sithira; Matsuda, Takahiro; Takine, Tetsuya

    In the IEEE 802.11 MAC protocol, access points (APs) are given the same priority as wireless terminals in terms of acquiring the wireless link, even though they aggregate several downlink flows. This feature leads to a serious throughput degradation of downlink flows, compared with uplink flows. In this paper, we propose a dynamic contention window control scheme for the IEEE 802.11e EDCA-based wireless LANs, in order to achieve fairness between uplink and downlink TCP flows while guaranteeing QoS requirements for real-time traffic. The proposed scheme first determines the minimum contention window size in the best-effort access category at APs, based on the number of TCP flows. It then determines the minimum and maximum contention window sizes in higher priority access categories, such as voice and video, so as to guarantee QoS requirements for these real-time traffic. Note that the proposed scheme does not require any modification to the MAC protocol at wireless terminals. Through simulation experiments, we show the effectiveness of the proposed scheme.

  14. Adaptive Backoff Algorithm for Contention Window for Dense IEEE 802.11 WLANs

    Directory of Open Access Journals (Sweden)

    Ikram Syed

    2016-01-01

    Full Text Available The performance improvement in IEEE 802.11 WLANs in widely fluctuating network loads is a challenging task. To improve the performance in this saturated state, we develop an adaptive backoff algorithm that maximizes the system throughput, reduces the collision probability, and maintains a high fairness for the IEEE 802.11 DCF under dense network conditions. In this paper, we present two main advantages of the proposed ABA-CW algorithm. First, it estimates the number of active stations and then calculates an optimal contention window based on the active station number. Each station calculates the channel state probabilities by observing the channel for the total backoff period. Based on these channel states probabilities, each station can estimate the number of active stations in the network, after which it calculates the optimal CW utilizing the estimated active number of stations. To evaluate the proposed mechanism, we derive an analytical model to determine the network performance. From our results, the proposed ABA-CW mechanism achieved better system performance compared to fixed-CW (BEB, EIED, LILD, and SETL and adaptive-CW (AMOCW, Idle Sense mechanisms. The simulation results confirmed the outstanding performance of the proposed mechanism in that it led to a lower collision probability, higher throughput, and high fairness.

  15. Self-Coexistence among IEEE 802.22 Networks: Distributed Allocation of Power and Channel

    Directory of Open Access Journals (Sweden)

    Sayef Azad Sakin

    2017-12-01

    Full Text Available Ensuring self-coexistence among IEEE 802.22 networks is a challenging problem owing to opportunistic access of incumbent-free radio resources by users in co-located networks. In this study, we propose a fully-distributed non-cooperative approach to ensure self-coexistence in downlink channels of IEEE 802.22 networks. We formulate the self-coexistence problem as a mixed-integer non-linear optimization problem for maximizing the network data rate, which is an NP-hard one. This work explores a sub-optimal solution by dividing the optimization problem into downlink channel allocation and power assignment sub-problems. Considering fairness, quality of service and minimum interference for customer-premises-equipment, we also develop a greedy algorithm for channel allocation and a non-cooperative game-theoretic framework for near-optimal power allocation. The base stations of networks are treated as players in a game, where they try to increase spectrum utilization by controlling power and reaching a Nash equilibrium point. We further develop a utility function for the game to increase the data rate by minimizing the transmission power and, subsequently, the interference from neighboring networks. A theoretical proof of the uniqueness and existence of the Nash equilibrium has been presented. Performance improvements in terms of data-rate with a degree of fairness compared to a cooperative branch-and-bound-based algorithm and a non-cooperative greedy approach have been shown through simulation studies.

  16. The TransPetro emergency response system

    Energy Technology Data Exchange (ETDEWEB)

    Filho, A.T.F.; Cardoso, V.F.; Carbone, R.; Berardinelli, R.P. [Petrobras-TransPetro, Rio de Janeiro (Brazil); Carvalho, M.T.M.; Casanova, M.A. [Pontificia Univ. Catolica, Rio de Janeiro (Brazil). Dept. de Informatica, TeCGraf

    2004-07-01

    Petrobras-TransPetro developed the TransPetro Emergency Response System in response to emergency situations at large oil pipelines or at terminal facilities located in sea or river harbour areas. The standard of excellence includes full compliance with environmental regulations set by the federal government. A distributed workflow management software called InfoPAE forms the basis of the system in which actions are defined, along with geographic and conventional data. The first prototype of InfoPAE was installed in 1999. Currently it is operational in nearly 80 installations. The basic concepts and functionality of the TransPetro Emergency Response System were outlined in this paper with reference to the mitigative actions that are based on an evaluation of the organization of the emergency teams; the communication procedures; characterization of the installations; definition of accidental scenarios; environmental sensitivity maps; simulation of oil spill trajectories and dispersion behaviour; geographical data of the area surrounding the installations; and, other conventional data related to the installations, including available equipment. The emergency response team can take action as soon as an accident is detected. The action plan involves characterizing several scenarios and delegating mitigative actions to specific sub-teams, each with access to geographic data on the region where the emergency occurred. 13 refs., 3 figs.

  17. Physics of trans-Planckian gravity

    International Nuclear Information System (INIS)

    Dvali, Gia; Folkerts, Sarah; Germani, Cristiano

    2011-01-01

    We study the field theoretical description of a generic theory of gravity flowing to Einstein general relativity in IR. We prove that, if ghost-free, in the weakly-coupled regime such a theory can never become weaker than general relativity. Using this fact, as a by-product, we suggest that in a ghost-free theory of gravity trans-Planckian propagating quantum degrees of freedom cannot exist. The only physical meaning of a trans-Planckian pole is the one of a classical state (black hole) which is described by the light IR quantum degrees of freedom and gives exponentially-suppressed contributions to virtual processes. In this picture Einstein gravity is UV self-complete, although not Wilsonian, and sub-Planckian distances are unobservable in any healthy theory of gravity. We then finally show that this UV/IR correspondence puts a severe constraint on any attempt of conventional Wilsonian UV-completion of trans-Planckian gravity. Specifically, there is no well-defined energy domain in which gravity could become asymptotically weak or safe.

  18. TransAlta 2003 annual report

    International Nuclear Information System (INIS)

    2004-01-01

    This annual report presents financial information from TransAlta Corp., along with a review of its operations throughout 2003 and a summary of the how the electric utility has performed in terms of power generation, independent power producers, transmission and energy marketing. TransAlta is one of the largest non-regulated power generation and wholesale marketing companies in Canada. It's assets include coal-fired, gas-fired, hydro and renewable generation facilities in Canada, the United States, Mexico and Australia. Reported earnings in 2003 were $1.26 per share compared to $1.17 in 2002. The strong first quarter was followed by harsh market conditions, low water levels which affected hydro production, and pricing restrictions in Ontario that reduced contribution from the Sarnia plant. This report outlines the utility's progress in increasing revenue and producing more power. In 2003, unplanned outages were reduced by 7 per cent and injury frequency rate was reduced by 27 per cent. The installation of 114 wind turbines in Fort Macleod, Alberta, increased TransAlta's renewable energy capacity to 3.7 per cent in 2003. The wind farm produces 75 MW of electricity, enough to power more than 32,500 homes annually. This report summarized the company's energy resource activities and presented an operations review as well as consolidated financial statements and common share information. This included the utility's assets, liabilities, revenues, expenses and cash flows. Revenue and expenditure statements were summarized by source. refs., tabs., figs

  19. TransCanada Corporation 2003 annual report

    International Nuclear Information System (INIS)

    2004-01-01

    This annual report presents financial information from TransCanada Corp., along with a review of its operations throughout 2003 and a summary of the how the company performed in terms of providing natural gas transmission and power services in North America. In 2003, TransCanada increased earnings from continuing operations by 7 per cent. It maintained a strong cash flow and continued to strengthen its balance sheet. More than 1.2 billion was invested and dividends were increased by 7 per cent in January 2004, for a total return to shareholders of 27 per cent, including dividends. In 2003, TransCanada also increased its ownership interest in Foothills Pipe Lines Ltd. to 100 per cent from 50 per cent. It secured a position in the Mackenzie Gas Pipeline Project and progressed the development of multiple liquefied natural gas projects in the northeast United States and eastern Canada. The company acquired 31.6 per cent interest in Bruce Power, adding nearly 1,500 megawatts base load generation to its portfolio. Plans are underway for cogeneration plants in Quebec, New Brunswick and Alberta. This report summarized the company's energy resource activities and presented an operations review as well as consolidated financial statements and common share information. This included the utility's assets, liabilities, revenues, expenses and cash flows. Revenue and expenditure statements were summarized by source. tabs., figs

  20. TransCanada Corporation 2004 annual report

    International Nuclear Information System (INIS)

    2005-01-01

    TransCanada is a leading North American energy company dealing with natural gas transmission, power generation and marketing opportunities. Financial information from TransCanada was presented in this annual report along with a review of its operations in 2004 and a summary of how the company performed in terms of providing natural gas transmission and power services in North America. In 2004, TransCanada increased earnings from continuing operations and maintained a strong cash flow and continued to strengthen its balance sheet. Achievements in 2004 included the acquisition of the Gas Transmission Northwest Pipeline System and the North Baja Pipeline System; the purchase of hydroelectric generation assets in New England with a total generating capacity of more than 500 MW; and the completed construction of two new gas-fired cogeneration plants, the 165 MW MacKay River facility in Alberta and the 90 MW Grandview facility in New Brunswick. The challenges in 2004 included the performance of the company's existing asset-based businesses and the new initiatives to produce another year of solid operating and financial results. This report summarized the company's energy resource activities and presented an operations review as well as consolidated financial statements and common share information. This included the utility's assets, liabilities, revenues, expenses and cash flows. Revenue and expenditure statements were summarized by source. tabs., figs

  1. Ultrasonic imaging in liquid sodium

    Energy Technology Data Exchange (ETDEWEB)

    Lubeigt, E. [CEA Cadarache, DEN/DTN/STCP/LIET, 13108 Saint-Paul-Lez-Durance Cedex (France); Laboratoire de Mecanique et d' Acoustique, CNRS UPR 7051, 13402 Marseille Cedex 20 (France); Mensah, S.; Chaix, J.F.; Rakotonarivo, S. [Laboratoire de Mecanique et d' Acoustique, CNRS UPR 7051, 13402 Marseille Cedex 20 (France); Gobillot, G. [CEA Cadarache, DEN/DTN/STCP/LIET, 13108 Saint-Paul-Lez-Durance Cedex (France)

    2015-07-01

    The fourth generation of nuclear reactor can use liquid sodium as the core coolant. When the reactor is operating, sodium temperatures can reach up to 600 deg. C. During maintenance periods, when the reactor is shut down, the coolant temperature is reduced to 200 deg. C. Because molten sodium is optically opaque, ultrasonic imaging techniques are developed for maintenance activities. Under-sodium imaging aims at i) checking the health of immersed structures. It should also allow ii) to assess component degradation or damage as cracks and shape defects as well as iii) the detection of lost objects. The under-sodium imaging system has to sustain high temperature (up to 300 deg. C) and hostility of the sodium environment. Furthermore, specific constraints such as transducers characteristics or the limited sensor mobility in the reactor vessel have to be considered. This work focuses on developing a methodology for detecting damages such as crack defects with ultrasound devices. Surface-breaking cracks or deep cracks are sought in the weld area, as welds are more subject to defects. Traditional methods enabled us to detect emerging cracks of submillimeter size with sodium-compatible high-temperature transducer. The presented approach relies on making use of prior knowledge about the environment through the implementation of differential imaging and time-reversal techniques. Indeed, this approach allows to detect a change by comparison with a reference measurement and by focusing back to any change in the environment. It is a means of analysis and understanding of the physical phenomena making it possible to design more effective inspection strategies. Difference between the measured signals reveals the acoustic field scattered by a perturbation (a crack for instance), which may occur between periodical measurements. The imaging method relies on the adequate combination of two computed ultrasonic fields, one forward and one adjoint. The adjoint field, which carries the

  2. Ultrasonic imaging in liquid sodium

    International Nuclear Information System (INIS)

    Lubeigt, E.; Mensah, S.; Chaix, J.F.; Rakotonarivo, S.; Gobillot, G.

    2015-01-01

    The fourth generation of nuclear reactor can use liquid sodium as the core coolant. When the reactor is operating, sodium temperatures can reach up to 600 deg. C. During maintenance periods, when the reactor is shut down, the coolant temperature is reduced to 200 deg. C. Because molten sodium is optically opaque, ultrasonic imaging techniques are developed for maintenance activities. Under-sodium imaging aims at i) checking the health of immersed structures. It should also allow ii) to assess component degradation or damage as cracks and shape defects as well as iii) the detection of lost objects. The under-sodium imaging system has to sustain high temperature (up to 300 deg. C) and hostility of the sodium environment. Furthermore, specific constraints such as transducers characteristics or the limited sensor mobility in the reactor vessel have to be considered. This work focuses on developing a methodology for detecting damages such as crack defects with ultrasound devices. Surface-breaking cracks or deep cracks are sought in the weld area, as welds are more subject to defects. Traditional methods enabled us to detect emerging cracks of submillimeter size with sodium-compatible high-temperature transducer. The presented approach relies on making use of prior knowledge about the environment through the implementation of differential imaging and time-reversal techniques. Indeed, this approach allows to detect a change by comparison with a reference measurement and by focusing back to any change in the environment. It is a means of analysis and understanding of the physical phenomena making it possible to design more effective inspection strategies. Difference between the measured signals reveals the acoustic field scattered by a perturbation (a crack for instance), which may occur between periodical measurements. The imaging method relies on the adequate combination of two computed ultrasonic fields, one forward and one adjoint. The adjoint field, which carries the

  3. Trans-Cultural, Trans-Language Practices: Potentialities for Rethinking Doctoral Education Pedagogies

    Directory of Open Access Journals (Sweden)

    Sarojni Choy

    2017-01-01

    Full Text Available Over the last decade, there has been a rapid increase in doctoral enrolments of Asian international students in Australian universities. While policies have been developed to meet the needs of these students, there seems to be some confusion around the terms internationalisation, globalisation, bi-cultural, inter-cultural, multi-cultural, and trans-cultural within these policies. In this paper, we define these terms and advocate for a policy position which orients to a futurist definition of culture. We then review the work of Michael Singh and his research team at Western Sydney University who have responded to this rapid increase in Asian international student doctoral enrolments in Australian universities by developing pedagogic principles around notions of trans-language and trans-cultural practices. In the final section of the paper, we then draw on our own experiences of doctoral supervision in Australian universities to reflect on our positioning within the pedagogic principles around trans-language and trans-cultural practices.

  4. Hand Gesture Recognition Using Ultrasonic Waves

    KAUST Repository

    AlSharif, Mohammed Hussain

    2016-04-01

    Gesturing is a natural way of communication between people and is used in our everyday conversations. Hand gesture recognition systems are used in many applications in a wide variety of fields, such as mobile phone applications, smart TVs, video gaming, etc. With the advances in human-computer interaction technology, gesture recognition is becoming an active research area. There are two types of devices to detect gestures; contact based devices and contactless devices. Using ultrasonic waves for determining gestures is one of the ways that is employed in contactless devices. Hand gesture recognition utilizing ultrasonic waves will be the focus of this thesis work. This thesis presents a new method for detecting and classifying a predefined set of hand gestures using a single ultrasonic transmitter and a single ultrasonic receiver. This method uses a linear frequency modulated ultrasonic signal. The ultrasonic signal is designed to meet the project requirements such as the update rate, the range of detection, etc. Also, it needs to overcome hardware limitations such as the limited output power, transmitter, and receiver bandwidth, etc. The method can be adapted to other hardware setups. Gestures are identified based on two main features; range estimation of the moving hand and received signal strength (RSS). These two factors are estimated using two simple methods; channel impulse response (CIR) and cross correlation (CC) of the reflected ultrasonic signal from the gesturing hand. A customized simple hardware setup was used to classify a set of hand gestures with high accuracy. The detection and classification were done using methods of low computational cost. This makes the proposed method to have a great potential for the implementation in many devices including laptops and mobile phones. The predefined set of gestures can be used for many control applications.

  5. An Authentication and Key Management Mechanism for Resource Constrained Devices in IEEE 802.11-based IoT Access Networks

    OpenAIRE

    Kim, Ki-Wook; Han, Youn-Hee; Min, Sung-Gi

    2017-01-01

    Many Internet of Things (IoT) services utilize an IoT access network to connect small devices with remote servers. They can share an access network with standard communication technology, such as IEEE 802.11ah. However, an authentication and key management (AKM) mechanism for resource constrained IoT devices using IEEE 802.11ah has not been proposed as yet. We therefore propose a new AKM mechanism for an IoT access network, which is based on IEEE 802.11 key management with the IEEE 802.1X aut...

  6. Ultrasonic monitoring of pitting corrosion

    Science.gov (United States)

    Jarvis, A. J. C.; Cegla, F. B.; Bazaz, H.; Lozev, M.

    2013-01-01

    Exposure to corrosive substances in high temperature environments can cause damage accumulation in structural steels, particularly in the chemical and petrochemical industries. The interaction mechanisms are complex and varied; however initial damage propagation often manifests itself in the form of localized areas of increased material loss. Recent development of an ultrasonic wall thickness monitoring sensor capable of withstanding temperatures in excess of 500°C has allowed permanent monitoring within such hostile environments, providing information on how the shape of a pulse which has reflected from a corroding surface can change over time. Reconstructing localized corrosion depth and position may be possible by tracking such changes in reflected pulse shape, providing extra information on the state of the backwall and whether process conditions should be altered to increase plant life. This paper aims to experimentally investigate the effect certain localized features have on reflected pulse shape by `growing' artificial defects into the backwall while wall thickness is monitored using the sensor. The size and complexity of the three dimensional scattering problem lead to the development of a semi-analytical simulation based on the distributed point source method (DPSM) which is capable of simulating pulse reflection from complex surfaces measuring approximately 17×10λ Comparison to experimental results show that amplitude changes are predicted to within approximately 1dB and that pulse shape changes are accurately modelled. All experiments were carried out at room temperature, measurements at high temperature will be studied in the future.

  7. Optimization of Ultrasonic Fabric Cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Hand, T.E.

    1998-05-13

    The fundamental purpose of this project was to research and develop a process that would reduce the cost and improve the environmental efficiency of the present dry-cleaning industry. This second phase of research (see report KCP-94-1006 for information gathered during the first phase) was intended to allow the optimal integration of all factors of ultrasonic fabric cleaning. For this phase, Garment Care performed an extensive literature search and gathered data from other researchers worldwide. The Garment Care-AlliedSignal team developed the requirements for a prototype cleaning tank for studies and acquired that tank and the additional equipment required to use it properly. Garment Care and AlliedSignal acquired the transducers and generators from Surftran Martin-Walter in Sterling Heights, Michigan. Amway's Kelly Haley developed the test protocol, supplied hundreds of test swatches, gathered the data on the swatches before and after the tests, assisted with the cleaning tests, and prepared the final analysis of the results. AlliedSignal personnel, in conjunction with Amway and Garment Care staff, performed all the tests. Additional planning is under way for future testing by outside research facilities. The final results indicated repeatable performance and good results for single layered fabric swatches. Swatches that were cleaned as a ''sandwich,'' that is, three or more layers.

  8. Problems and solutions in application of IEEE standards at Savannah River Site, Department of Energy (DOE) nuclear facilities

    International Nuclear Information System (INIS)

    Lee, Y.S.; Bowers, T.L.; Chopra, B.J.; Thompson, T.T.; Zimmerman, E.W.

    1993-01-01

    The Department of Energy (DOE) Nuclear Material Production Facilities at the Savannah River Site (SRS) were designed, constructed, and placed into operation in the early 1950's, based on existing industry codes/standards, design criteria, analytical procedures. Since that time, DOE has developed Orders and Polices for the planning, design and construction of DOE Nuclear Reactor Facilities which invoke or reference commercial nuclear reactor codes and standards. The application of IEEE reactor design requirements such as Equipment Qualification, Seismic Qualification, Single Failure Criteria, and Separation Requirement, to non-reactor facilities has been a problem since the IEEE reactor criteria do not directly confirm to the needs of non-reactor facilities. SRS Systems Engineering is developing a methodology for the application of IEEE Standards to non-reactor facilities at SRS

  9. A distributed scheme to manage the dynamic coexistence of IEEE 802.15.4-based health-monitoring WBANs.

    Science.gov (United States)

    Deylami, Mohammad N; Jovanov, Emil

    2014-01-01

    The overlap of transmission ranges between wireless networks as a result of mobility is referred to as dynamic coexistence. The interference caused by coexistence may significantly affect the performance of wireless body area networks (WBANs) where reliability is particularly critical for health monitoring applications. In this paper, we analytically study the effects of dynamic coexistence on the operation of IEEE 802.15.4-based health monitoring WBANs. The current IEEE 802.15.4 standard lacks mechanisms for effectively managing the coexistence of mobile WBANs. Considering the specific characteristics and requirements of health monitoring WBANs, we propose the dynamic coexistence management (DCM) mechanism to make IEEE 802.15.4-based WBANs able to detect and mitigate the harmful effects of coexistence. We assess the effectiveness of this scheme using extensive OPNET simulations. Our results indicate that DCM improves the successful transmission rates of dynamically coexisting WBANs by 20%-25% for typical medical monitoring applications.

  10. Simultaneous transmission of the IEEE 802.11 radio signal and optical Gbit Ethernet over the multimode fiber link

    Science.gov (United States)

    Maksymiuk, L.; Podziewski, A.

    2015-09-01

    In the paper we present a successful joint transmission of the IEEE 802.11 signal and an optical Gbit Ethernet over a multimode fiber based link. Most importantly, the multiplexation of both signals was performed in the optical domain. Due to the utilization of the multimode fiber the OBI noise was avoided and both channels were able to operate at the same wavelength. We prove that potential RoF link for IEEE 802.11 signal distribution may be used to additionally transmit other signals as Gbit Ethernet and therefore utilize the fiber infrastructure installed more effectively. The qualities of both the IEEE 802.11 and Ethernet transmissions fulfilled the requirements imposed by appropriate standards.

  11. A Cross-Layer Key Management Scheme for MIPv6 Fast Handover over IEEE 802.11 Wireless LAN

    Directory of Open Access Journals (Sweden)

    Chang-Seop Park

    2015-01-01

    Full Text Available A new key management and security scheme is proposed to integrate Layer Two (L2 and Layer Three (L3 keys for secure and fast Mobile IPv6 handover over IEEE 802.11 Wireless Local Area Network (WLAN. Unlike the original IEEE 802.11-based Mobile IPv6 Fast Handover (FMIPv6 that requires time-consuming IEEE 802.1x-based Extensible Authentication Protocol (EAP authentication on each L3 handover, the newly proposed key management and security scheme requires only one 802.1x-EAP regardless of how many L3 handovers occur. Therefore, the proposed scheme reduces the handover latency that results from a lengthy 802.1x-based EAP. The proposed key management and security scheme is extensively analyzed in terms of security and performance, and the proposed security scheme is shown to be more secure than those that were previously proposed.

  12. TransCanada PipeLines Limited 1998 annual report : TransCanada energy solutions

    International Nuclear Information System (INIS)

    1999-01-01

    Financial information from TransCanada PipeLines Limited and a review of the company's 1998 operations was made available for the benefit of shareholders. TransCanada's pipeline system transports natural gas and crude oil from Western Canada Sedimentary Basin to North America's major energy markets. Net earnings from continuing operations for 1998, before unusual charges, were $575 million ($ 355 million after unusual charges) compared to $522 million for 1997. Solid performances from the energy transmission and international business, when compared to 1997, were more than offset by a decreased contribution from energy processing. TransCanada recorded integration costs of $166 million, after tax, related to the merger with NOVA in 1998, which was the major operational accomplishment during the year, creating a seamless economic energy delivery, processing and marketing system from the wellhead to the market. tabs., figs

  13. Sexual desire in trans persons: associations with sex reassignment treatment.

    Science.gov (United States)

    Wierckx, Katrien; Elaut, Els; Van Hoorde, Birgit; Heylens, Gunter; De Cuypere, Griet; Monstrey, Stan; Weyers, Steven; Hoebeke, Piet; T'Sjoen, Guy

    2014-01-01

    Sex steroids and genital surgery are known to affect sexual desire, but little research has focused on the effects of cross-sex hormone therapy and sex reassignment surgery on sexual desire in trans persons. This study aims to explore associations between sex reassignment therapy (SRT) and sexual desire in a large cohort of trans persons. A cross-sectional single specialized center study including 214 trans women (male-to-female trans persons) and 138 trans men (female-to-male trans persons). Questionnaires assessing demographics, medical history, frequency of sexual desire, hypoactive sexual desire disorder (HSDD), and treatment satisfaction. In retrospect, 62.4% of trans women reported a decrease in sexual desire after SRT. Seventy-three percent of trans women never or rarely experienced spontaneous and responsive sexual desire. A third reported associated personal or relational distress resulting in a prevalence of HSDD of 22%. Respondents who had undergone vaginoplasty experienced more spontaneous sexual desire compared with those who planned this surgery but had not yet undergone it (P = 0.03). In retrospect, the majority of trans men (71.0%) reported an increase in sexual desire after SRT. Thirty percent of trans men never or rarely felt sexual desire; 39.7% from time to time, and 30.6% often or always. Five percent of trans men met the criteria for HSDD. Trans men who were less satisfied with the phalloplasty had a higher prevalence of HSDD (P = 0.02). Trans persons who were more satisfied with the hormonal therapy had a lower prevalence of HSDD (P = 0.02). HSDD was more prevalent in trans women compared with trans men. The majority of trans women reported a decrease in sexual desire after SRT, whereas the opposite was observed in trans men. Our results show a significant sexual impact of surgical interventions and both hormonal and surgical treatment satisfaction on the sexual desire in trans persons. © 2013 International Society for Sexual

  14. The digital ultrasonic test unit for automatic equipment

    International Nuclear Information System (INIS)

    Hiraoka, T.; Matsuyama, H.

    1976-01-01

    The operations and features of the ultrasonic test unit used and the digital data processing techniques employed are described. This unit is used for a few hundred multi-channel automatic ultrasonic test equipment

  15. Ultrasonic-assisted manufacturing processes: Variational model and numerical simulations

    KAUST Repository

    Siddiq, Amir; El Sayed, Tamer

    2012-01-01

    We present a computational study of ultrasonic assisted manufacturing processes including sheet metal forming, upsetting, and wire drawing. A fully variational porous plasticity model is modified to include ultrasonic softening effects

  16. P-Scan provides accuracy and repeatability in ultrasonics

    International Nuclear Information System (INIS)

    Keys, R.L.

    1987-01-01

    The P-Scan (Projection image scanning technique) is an automated ultrasonic inspection technique, developed to overcome the problems with accuracy and repeatability experienced with manual ultrasonic systems. The equipment and its applications are described. (author)

  17. Method and apparatus to characterize ultrasonically reflective contrast agents

    Science.gov (United States)

    Pretlow, Robert A., III (Inventor)

    1993-01-01

    A method and apparatus for characterizing the time and frequency response of an ultrasonically reflective contrast agent is disclosed. An ultrasonically reflective contrast agent is injected, under constant pressure, into a fluid flowing through a pump flow circuit. The fluid and the ultrasonically reflective contrast agent are uniformly mixed in a mixing chamber, and the uniform mixture is passed through a contrast agent chamber. The contrast agent chamber is acoustically and axially interposed between an ultrasonic transducer chamber and an acoustic isolation chamber. A pulse of ultrasonic energy is transmitted into the contrast agent chamber from the ultrasonic transducer chamber. An echo waveform is received from the ultrasonically reflective contrast agent, and it is analyzed to determine the time and frequency response of the ultrasonically reflective contrast agent.

  18. Automated electronic intruder simulator for evaluation of ultrasonic intrusion detectors

    International Nuclear Information System (INIS)

    1979-01-01

    An automated electronic intruder simulator for testing ultrasonic intrusion detectors is described. This simulator is primarily intended for use in environmental chambers to determine the effects of temperature and humidity on the operation of ultrasonic intrusion detectors

  19. Development and Application of an Ultrasonic Gas Flowmeter

    International Nuclear Information System (INIS)

    Hwang, Won Ho; Jeong, Hee Don; Park, Sang Gug; Jhang, Kyung Young

    2002-01-01

    This paper describes the development and the field application of the ultrasonic gas flowmeter for accurate measurement of the volumetric flow rate of gases in a harsh environmental conditions in iron and steel making company. This ultrasonic flowmeter is especially suited for measuring LDG, COG, BFG gases produced in iron and steel making process. This is a transit time type ultrasonic flowmeter. We have developed the transmitting and receiving algorithm of ultrasonic wave and the ultrasonic signal processing algorithm to develope a transit time type ultrasonic flowmeter. We have evaluated the performance of ultrasonic flowmeter by the calibration system with Venturi type standard flowmeter. We has confirmed its reliability by extensive field tests for a year in POSCO, iron and steel making company. Now we have developed the commercial model of ultrasonic flowmeter and applied to the POSCO gas line

  20. Study on electrical impedance matching for broadband ultrasonic transducer

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Geon Woo [University of Science and Technology, Daejeon (Korea, Republic of); Kim, Ki Bok [Korea Research Institute of Standards and Science, Center for Safety Measurement, Daejeon (Korea, Republic of); Baek, Kwang Sae [Elache Co., Busan (Korea, Republic of)

    2017-02-15

    Ultrasonic transducers with high resolution and resonant frequency are required to detect small defects (less than hundreds of μm) by ultrasonic testing. The resonance frequency and resolution of an ultrasonic transducer are closely related to the thickness of piezo-electric materials, backing materials, and the electric impedance matching technique. Among these factors, electrical impedance matching plays an important role because it can reduce the loss and reflection of ultrasonic energy differences in electrical impedance between an ultrasonic transducer and an ultrasonic defects detecting system. An LC matching circuit is the most frequently used electric matching method. It is necessary for the electrical impedance of an ultrasonic transducer to correspond to approximately 50 Ω to compensate the difference in electrical impedance between both connections. In this study, a 15 MHz immersion ultrasonic transducer was fabricated and an LC electrical impedance circuit was applied to that for having broad-band frequency characteristic.

  1. Ultrasonic extraction of flavonoids and phenolics from loquat ...

    African Journals Online (AJOL)

    Administrator

    2011-06-08

    Jun 8, 2011 ... ultrasonic pharmaceutical managing machine (Sinobest electronic. Co. Ltd., Jining, Shangdong ... During the ultrasonic treatment, the temperature ..... essential oil extraction by a hydrodistillation process using a 2(4) complete ...

  2. Electrocautery causes more ischemic peritoneal tissue damage than ultrasonic dissection.

    NARCIS (Netherlands)

    Broek, R.P.G ten; Wilbers, J.; Goor, H. van

    2011-01-01

    BACKGROUND: Minimizing peritoneal tissue injury during abdominal surgery has the benefit of reducing postoperative inflammatory response, pain, and adhesion formation. Ultrasonic dissection seems to reduce tissue damage. This study aimed to compare electrocautery and ultrasonic dissection in terms

  3. Studies on Section XI ultrasonic repeatability

    International Nuclear Information System (INIS)

    Jamison, T.D.; McDearman, W.R.

    1981-05-01

    A block representative of a nuclear component has been welded containing intentional defects. Acoustic emission data taken during the welding correlate well with ultrasonic data. Repetitive ultrasonic examinations have been performed by skilled operators using a procedure based on that desribed in ASME Section XI. These examinations were performed by different examination teams using different ultrasonic equipment in such a manner that the effects on the repeatability of the ultrasonic test method caused by the operator and by the use of different equipment could be estimated. It was tentatively concluded that when considering a large number of inspections: (1) there is no significant difference in indication sizing between operators, and (2) there is a significant difference in amplitude and defect sizing when instruments having different, Code acceptable operating characteristics are used. It was determined that the Section XI sizing parameters follow a bivariate normal distribution. Data derived from ultrasonically and physically sizing indications in nuclear components during farication show that the Section XI technique tends to overestimate the size of the reflectors

  4. Further Investigations on Simultaneous Ultrasonic Coal Flotation

    Directory of Open Access Journals (Sweden)

    Safak Gokhan Ozkan

    2017-09-01

    Full Text Available This study investigates the flotation performance of a representative hard coal slime sample (d80 particle size of minus 0.2 mm obtained from the Prosper-Haniel coal preparation plant located in Bottrop, Germany. Flotation was carried out with a newly designed flotation cell refurbished from an old ultrasonic cleaning bath (2.5 L volume equipped with a single frequency (35 kHz and two different power levels (80–160 W and a sub-aeration-type flotation machine operating at a stable impeller speed (1200 rpm and air rate (2.5 L/min. The reagent combination for conventional and simultaneous ultrasonic coal flotation tests was Ekofol-440 at variable dosages (40–300 g/t with controlling water temperature (20–25 °C at natural pH (6.5–7.0. The batch coal flotation results were analyzed by comparing the combustible recovery (% and separation efficiency (% values, taking mass yield and ash concentrations of the froths and tailings into account. It was found that simultaneous ultrasonic coal flotation increased yield and recovery values of the floated products with lower ash values than the conventional flotation despite using similar reagent dosages. Furthermore, particle size distribution of the ultrasonically treated and untreated coals was measured. Finely distributed coal particles seemed to be agglomerated during the ultrasonic treatment, while ash-forming slimes were removed by hydrodynamic cavitation.

  5. Standard practice for leaks using ultrasonics

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    1.1 Practice A, Pressurization—This practice covers procedures for calibration of ultrasonic instruments, location, and estimated measurements of gas leakage to atmosphere by the airborne ultrasonic technique. 1.2 In general practice this should be limited to leaks detected by two classifications of instruments, Class I and Class II. Class I instruments should have a minimum detectable leak rate of 6.7 × 10−7 mol/s (1.5 × 10−2 std. cm3/s at 0°C) or more for the pressure method of gas leakage to atmosphere. Class II instruments should have a minimal detectable leak rate of 6.7 × 10−6 mol/s (1.5 × 10−1 std. cm3/s at 0°C) or more for the pressure method of gas leakage to atmosphere. Refer to Guide E432 for additional information. 1.3 Practice B, Ultrasonic Transmitter—For object under test not capable of being pressurized but capable of having ultrasonic tone placed/injected into the test area to act as an ultrasonic leak trace source. 1.3.1 This practice is limited to leaks producing leakage o...

  6. Ultrasonic imaging in LMFBRs using digital techniques

    International Nuclear Information System (INIS)

    Fothergill, J.R.; McKnight, J.A.; Barrett, L.M.

    Ultrasonic technology for providing images of components immersed in the opaque sodium of LMFBRs is being developed at RNL. For many years the application has been restricted by the unavailability of convenient ultrasonic sources and receivers capable of withstanding the reactor environment. Until recently, for example, important ultrasonic instrument design, such as for future sweep arms, had to be based on waveguided ultrasonics. RNL have developed an economic immersible transducer that can be deployed during reactor shut-down, when many demands for ultrasonic imaging are made. The transducer design is not suited at present to the sophisticated techniques of phased arrays; consequently image formation must depend on the physical scanning of a target using one or more transducers in pulse-echo mode. The difficulties of access into a fast reactor impose further restrictions. Some applications may involve easy scanning sequences, thus the sweep arm requires only a rotation to provide a map of the reactor core area. For a more detailed examination of the same area, however, special engineering solutions are needed to provide a more satisfactory scanning sequence. A compromise solution involving the rotating shield movement is being used for a PFR experiment to examine a limited area of the core. (author)

  7. Uncertainty estimation of ultrasonic thickness measurement

    International Nuclear Information System (INIS)

    Yassir Yassen, Abdul Razak Daud; Mohammad Pauzi Ismail; Abdul Aziz Jemain

    2009-01-01

    The most important factor that should be taken into consideration when selecting ultrasonic thickness measurement technique is its reliability. Only when the uncertainty of a measurement results is known, it may be judged if the result is adequate for intended purpose. The objective of this study is to model the ultrasonic thickness measurement function, to identify the most contributing input uncertainty components, and to estimate the uncertainty of the ultrasonic thickness measurement results. We assumed that there are five error sources significantly contribute to the final error, these sources are calibration velocity, transit time, zero offset, measurement repeatability and resolution, by applying the propagation of uncertainty law to the model function, a combined uncertainty of the ultrasonic thickness measurement was obtained. In this study the modeling function of ultrasonic thickness measurement was derived. By using this model the estimation of the uncertainty of the final output result was found to be reliable. It was also found that the most contributing input uncertainty components are calibration velocity, transit time linearity and zero offset. (author)

  8. IEEE Xplore® Digital Library - Evolving to Meet YOUR Changing Needs

    OpenAIRE

    2014-01-01

    Представлена презентация доклада "Использование платформы IEEE Digital Library: уникальные научные публикации в области электроники, радиосвязи, вычислительной техники, информационных технологий, энергетики, машиностроения, физики, химии, геологии, нанотехнологий" Эстер Лукаш, специалиста по обучению IEEE (Германия), на семинаре «Использование платформы IEEE Digital Library», прошедшем 02 октября 2014 года в УрФУ, на английском языке....

  9. Ultrasonic scanner for stainless steel weld inspections. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Kupperman, D. S.; Reimann, K. J.

    1978-09-01

    The large grain size and anisotropic nature of stainless steel weld metal make conventional ultrasonic testing very difficult. A technique is evaluated for minimizing the coherent ultrasonic noise in stainless steel weld metal. The method involves digitizing conventional ''A-scan'' traces and averaging them with a minicomputer. Results are presented for an ultrasonic scanner which interrogates a small volume of the weld metal while averaging the coherent ultrasonic noise.

  10. Training methods in non-destructive examination with ultrasonic testing

    International Nuclear Information System (INIS)

    Walte, F.

    1986-01-01

    German concept for inspection of LWR, leak before break, basic safety; General inspection methods; Ultrasonic inspection - basic principle, generation of ultrasound, bulk and surface waves, piezo electric and electromagnetic transducers, energy balance, scattering and adsorption, divergence; Ultra techniques in compliance with KTA-rules - pulse-echo, tandem, throughtransmission; Valuation of ultrasonic indications; Pre- and in-service inspection; Practical part - ultrasonic equipment, ultrasonic piezo electric transducers, wall thickness measurement, crack depth measurement with potential drop technique. (orig.)

  11. Ultrasonic Cleaning of Nuclear Steam Generator by Micro Bubble

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Woo Tae [Korea Hydro and Nuclear Power Co., Daejeon (Korea, Republic of); Kim, Sang Tae; Yoon, Sang Jung [Sae-An Engineering Co., Seoul (Korea, Republic of)

    2012-05-15

    In this paper, we present ultrasonic cleaning technology for a nuclear steam generator using micro bubble. We could extend the boundary of ultrasonic cleaning by using micro bubbles in water. Ultrasonic energy measured was increased about 5 times after the generation of micro bubbles in water. Furthermore, ultrasound energy was measured to be strong enough to create cavitation even though the ultrasound sensor was about 2 meters away from the ultrasonic transducer

  12. Contact-free ultrasonic testing: applications to metrology and NDT

    International Nuclear Information System (INIS)

    Le Brun, A.

    1988-01-01

    In some cases classical ultrasonic testing is impossible because of adverse environment (high temperature, ionizing radiations, etc). Ultrasonic waves are created by laser impact and detected by electromagneto-acoustic transducers or laser interferometry. Association of ultrasonics generation by photoacoustic effect and reception by heterodyne interferometer is promising for the future [fr

  13. Experiences in using ultrasonic holography with numerical and optical reconstruction

    International Nuclear Information System (INIS)

    Schmitz, V.; Wosnitza, M.

    1978-01-01

    At present, ultrasonic holography can resolve and image faults of 1 mm and more and with distances of one ultrasonic wavelength. The main field of application is for thick-walled structural components. Depending on the expected orientation, test probe arrangements as in standard ultrasonic testing are chosen. (orig./RW) [de

  14. Numerical shaping of the ultrasonic wavelet

    International Nuclear Information System (INIS)

    Bonis, M.

    1991-01-01

    Improving the performance and the quality of ultrasonic testing requires the numerical control of the shape of the driving signal applied to the piezoelectric transducer. This allows precise shaping of the ultrasonic field wavelet and corrections for the physical defects of the transducer, which are mainly due to the damper or the lens. It also does away with the need for an accurate electric matching. It then becomes feasible to characterize, a priori, the ultrasonic wavelet by means of temporal and/or spectral specifications and to use, subsequently, an adaptative algorithm to calculate the corresponding driving wavelet. Moreover, the versatility resulting from the numerical control of this wavelet allows it to be changed in real time during a test

  15. Method of noncontacting ultrasonic process monitoring

    Science.gov (United States)

    Garcia, Gabriel V.; Walter, John B.; Telschow, Kenneth L.

    1992-01-01

    A method of monitoring a material during processing comprising the steps of (a) shining a detection light on the surface of a material; (b) generating ultrasonic waves at the surface of the material to cause a change in frequency of the detection light; (c) detecting a change in the frequency of the detection light at the surface of the material; (d) detecting said ultrasonic waves at the surface point of detection of the material; (e) measuring a change in the time elapsed from generating the ultrasonic waves at the surface of the material and return to the surface point of detection of the material, to determine the transit time; and (f) comparing the transit time to predetermined values to determine properties such as, density and the elastic quality of the material.

  16. Determine bond strength by ultrasonic measurement

    International Nuclear Information System (INIS)

    Brown, C.M.

    1978-01-01

    Application of ultrasonic methods for the evaluation and measurement of bond strength has been the object of numerous investigations in the last fifteen years. Some investigators have reported good success (in limited application) while others have experienced dismal failure. One problem common to all investigations was the difficulty in extracting and isolating the many components which comprise the ultrasonic signal reflected from a bonded interface. Part of this problem was due to manually extracting individual parameters from large volumes of raw data. However, with the vast technology now available in the field of signal analysis and computerized data processing, it is feasible to isolate and analyze individual parameters within the ultrasonic signal for great volumes of raw data

  17. Ultrasonic filtration of industrial chemical solutions

    Science.gov (United States)

    Cosma, T.

    1974-01-01

    The practical results obtained as a result of filtering industrial chemical solutions under continuous flow conditions with the aid of an ultrasonic filter are presented. The main part of the assembly consists of an ultrasonic generator with an output power of about 400 W and the filtration assembly, in which there is a magnetostrictive amplifier constructed for 20.5 kHz. In addition to ensuring a continuous flow of filtered solution, ultrasonic filters can be replaced or cleaned at intervals of time that are 8-10 times greater than in the case of mechanical filters. They yield considerably better results as far as the size of the filtered particles is concerned. The parameters on which filtration quality depends are also presented.

  18. Ultrasonic grinding of optical materials

    Science.gov (United States)

    Cahill, Michael; Bechtold, Michael; Fess, Edward; Stephan, Thomas; Bechtold, Rob

    2017-10-01

    Hard ceramic optical materials such as sapphire, ALON, Spinel, PCA, or Silicon Carbide can present a significant challenge in manufacturing precision optical components due to their tough mechanical properties. These are also the same mechanical properties that make them desirable materials when used in harsh environments. Slow processing speeds, premature tool wear, and poor surface quality are common results of the tough mechanical properties of these materials. Often, as a preparatory stage for polishing, the finish of the ground surface greatly influences the polishing process and the resulting finished product. To overcome these challenges, OptiPro Systems has developed an ultrasonic assisted grinding technology, OptiSonic, which has been designed for the precision optics and ceramics industry. OptiSonic utilizes a custom tool holder designed to produce oscillations, in microns of amplitude, in line with the rotating spindle. A software package, IntelliSonic, is integral to the function of this platform. IntelliSonic can automatically characterize tooling during setup to identify and select the ideal resonant peak which to operate at. Then, while grinding, IntelliSonic continuously adjusts the output frequency for optimal grinding efficiency while in contact with the part. This helps maintain a highly consistent process under changing load conditions for a more precise surface. Utilizing a variety of instruments, tests have proven to show a reduction in force between tool and part by up to 50%, while increasing the surface quality and reducing tool wear. This paper will present the challenges associated with these materials and solutions created to overcome them.

  19. Ultrasonic sludge pretreatment under pressure.

    Science.gov (United States)

    Le, Ngoc Tuan; Julcour-Lebigue, Carine; Delmas, Henri

    2013-09-01

    The objective of this work was to optimize the ultrasound (US) pretreatment of sludge. Three types of sewage sludge were examined: mixed, secondary and secondary after partial methanisation ("digested" sludge). Thereby, several main process parameters were varied separately or simultaneously: stirrer speed, total solid content of sludge (TS), thermal operating conditions (adiabatic vs. isothermal), ultrasonic power input (PUS), specific energy input (ES), and for the first time external pressure. This parametric study was mainly performed for the mixed sludge. Five different TS concentrations of sludge (12-36 g/L) were tested for different values of ES (7000-75,000 kJ/kgTS) and 28 g/L was found as the optimum value according to the solubilized chemical oxygen demand in the liquid phase (SCOD). PUS of 75-150 W was investigated under controlled temperature and the "high power input - short duration" procedure was the most effective at a given ES. The temperature increase in adiabatic US application significantly improved SCOD compared to isothermal conditions. With PUS of 150 W, the effect of external pressure was investigated in the range of 1-16 bar under isothermal and adiabatic conditions for two types of sludge: an optimum pressure of about 2 bar was found regardless of temperature conditions and ES values. Under isothermal conditions, the resulting improvement of sludge disintegration efficacy as compared to atmospheric pressure was by 22-67% and 26-37% for mixed and secondary sludge, respectively. Besides, mean particle diameter (D[4,3]) of the three sludge types decreased respectively from 408, 117, and 110 μm to about 94-97, 37-42, and 36-40 μm regardless of sonication conditions, and the size reduction process was much faster than COD extraction. Copyright © 2013 Elsevier B.V. All rights reserved.

  20. Advances in ultrasonic fuel cleaning

    International Nuclear Information System (INIS)

    Blok, J.; Frattini, P.; Moser, T.

    2002-01-01

    The economics of electric generation is requiring PWR plant operators to consider higher fuel duty and longer cycles. As a result, sub-cooled nucleate boiling is now an accepted occurrence in the upper spans of aggressively driven PWR cores. Thermodynamic and hydraulic factors determine that the boiling surfaces of the fuel favor deposition of corrosion products. Thus, the deposits on high-duty fuel tend to be axially distributed in an inhomogeneous manner. Axial offset anomaly (AOA) is the result of axially non-homogeneous distribution of boron compounds in these axially variable fuel deposits. Besides their axial asymmetry, fuel deposits in boiling cores tend to be qualitatively different from deposits on non-boiling fuel. Thus, deposits on moderate-duty PWR fuel are generally iron rich, predominating in nickel ferrites. Deposits on cores with high boiling duty, on the other hand, tend to be rich in nickel, with sizeable fractions of NiO or elemental nickel. Other unexpected compounds such as m-ZrO 2 and Ni-Fe oxy-borates have been found in significant quantity in deposits on boiling cores. This paper describes the ultrasonic fuel cleaning technology developed by EPRI. Data will be presented to confirm that the method is effective for removing fuel deposits from both high-duty and normal-duty fuel. The report will describe full-core fuel cleaning using the EPRI technology for Callaway Cycle 12 reload fuel. The favorable impact of fuel cleaning on Cycle 12 AOA performance will also be presented. (authors)

  1. Fault-Tolerant Topology and Routing Synthesis for IEEE Time-Sensitive Networking

    DEFF Research Database (Denmark)

    Gavrilut, Voica Maria; Zarrin, Bahram; Pop, Paul

    2017-01-01

    of the applications are satisffied. We propose three approaches to solve this optimization problem: (1) a heuristic solution, (2) a Greedy Randomized Adaptive Search Procedure (GRASP) metaheuristic, and (3) a Constraint Programmingbased model. The approaches are evaluated on several test cases, including a test case......Time-Sensitive Networking (TSN) is a set of IEEE standards that extend Ethernet for safety-critical and real-time applications. TSN is envisioned to be widely used in several applications areas, from industrial automation to in-vehicle networking. A TSN network is composed of end systems...... interconnected by physical links and bridges (switches). The data in TSN is exchanged via streams. We address safety-critical real-time systems, and we consider that the streams use the Urgency-Based Scheduler (UBS) traffic-type, suitable for hard real-time traffic. We are interested in determining a fault...

  2. Synchronous ethernet and IEEE 1588 in telecoms next generation synchronization networks

    CERN Document Server

    2013-01-01

    This book addresses the multiple technical aspects of the distribution of synchronization in new generation telecommunication networks, focusing in particular on synchronous Ethernet and IEEE1588 technologies. Many packet network engineers struggle with understanding the challenges that precise synchronization distribution can impose on networks. The usual “why”, “when” and particularly “how” can cause problems for many engineers. In parallel to this, some other markets have identical synchronization requirements, but with their own design requirements, generating further questions. This book attempts to respond to the different questions by providing background technical information. Invaluable information on state of-the-art packet network synchronization and timing architectures is provided, as well as an unbiased view on the synchronization technologies that have been internationally standardized over recent years, with the aim of providing the average reader (who is not skilled in the art) wi...

  3. 12th ACIS/IEEE International Conference on Computer Science and Information Science

    CERN Document Server

    2013-01-01

    This edited book presents scientific results of the 12th IEEE/ACIS International Conference on Computer and Information Science (ICIS 2013) which was held on June 16-20, 2013 in Toki Messe, Niigata, Japan. The aim of this conference was to bring together scientists, engineers, computer users, and students to share their experiences and exchange new ideas, research results about all aspects (theory, applications and tools) of computer and information science, and to discuss the practical challenges encountered along the way and the solutions adopted to solve them The conference organizers selected the best 20 papers from those papers accepted for presentation at the conference. The papers were chosen based on review scores submitted by members of the program committee, and underwent further rigorous rounds of review.    

  4. Efficient Beacon Collision Resolution Procedure for IEEE 802.15.4 /Zigbee Wireless Personal Area Networks

    Directory of Open Access Journals (Sweden)

    Bassam A. Zafar

    2017-04-01

    Full Text Available While IEEE 802.15.4/Zigbee is a promising technology for Wireless Personal Area Networks, several transmission problems are not yet resolved. In particular, the problem of beacon transmission interferences is causing the device connection loss to the network. In order to resolve this problem, we present a new distributed and reactive procedure for beacon collision resolution. It is an extension of the alignment procedure to reorganize randomly the beacon transmission time when a collision has occurred. The detail of the proposed procedure will be fully described and analyzed. The performance of our approach is performed by simulations. The results show that our approach reduces the collision probability and the device disconnections consequently.

  5. The IEEE guide to writing in the engineering and technical fields

    CERN Document Server

    Kmiec, David

    2017-01-01

    This book introduces students and practicing engineers to all the components of writing in the workplace. It teaches readers how considerations of audience and purpose govern the structure of their documents within particular work settings. The IEEE Guide to Writing in the Engineering and Technical Fields is broken up into two sections: "Writing in Engineering Organizations" and "What Can You Do With Writing?" The first section helps readers approach their writing in a logical and persuasive way as well as analyze their purpose for writing. The second section demonstrates how to distinguish rhetorical situations and the generic forms to inform, train, persuade, and collaborate. The emergence of the global workplace has brought with it an increasingly important role for effective technical communication. Engineers more often need to work in cross-functional teams with people in different disciplines, in different countries, and in different parts of the world. Engineers must know how to communicate in a rapid...

  6. Development of a low mobility IEEE 802.15.4 compliant VANET system for urban environments.

    Science.gov (United States)

    Nazabal, Juan Antonio; Falcone, Francisco; Fernández-Valdivielso, Carlos; Matías, Ignacio Raúl

    2013-05-29

    The use of Vehicular Ad-Hoc Networks (VANETs) is growing nowadays and it includes both roadside-to-vehicle communication (RVC) and inter-vehicle communication (IVC). The purpose of VANETs is to exchange useful information between vehicles and the roadside infrastructures for making an intelligent use of them. There are several possible applications for this technology like: emergency warning system for vehicles, cooperative adaptive cruise control or collision avoidance, among others. The objective of this work is to develop a VANET prototype system for urban environments using IEEE 802.15.4 compliant devices. Simulation-based values of the estimated signal strength and radio link quality values are obtained and compared with measurements in outdoor conditions to validate an implemented VANET system. The results confirm the possibility of implementing low cost vehicular communication networks operating at moderate vehicular speeds.

  7. 2011 IEEE Visualization Contest winner: Visualizing unsteady vortical behavior of a centrifugal pump.

    Science.gov (United States)

    Otto, Mathias; Kuhn, Alexander; Engelke, Wito; Theisel, Holger

    2012-01-01

    In the 2011 IEEE Visualization Contest, the dataset represented a high-resolution simulation of a centrifugal pump operating below optimal speed. The goal was to find suitable visualization techniques to identify regions of rotating stall that impede the pump's effectiveness. The winning entry split analysis of the pump into three parts based on the pump's functional behavior. It then applied local and integration-based methods to communicate the unsteady flow behavior in different regions of the dataset. This research formed the basis for a comparison of common vortex extractors and more recent methods. In particular, integration-based methods (separation measures, accumulated scalar fields, particle path lines, and advection textures) are well suited to capture the complex time-dependent flow behavior. This video (http://youtu.be/oD7QuabY0oU) shows simulations of unsteady flow in a centrifugal pump.

  8. Vispubdata.org: A Metadata Collection About IEEE Visualization (VIS) Publications.

    Science.gov (United States)

    Isenberg, Petra; Heimerl, Florian; Koch, Steffen; Isenberg, Tobias; Xu, Panpan; Stolper, Charles D; Sedlmair, Michael; Chen, Jian; Moller, Torsten; Stasko, John

    2017-09-01

    We have created and made available to all a dataset with information about every paper that has appeared at the IEEE Visualization (VIS) set of conferences: InfoVis, SciVis, VAST, and Vis. The information about each paper includes its title, abstract, authors, and citations to other papers in the conference series, among many other attributes. This article describes the motivation for creating the dataset, as well as our process of coalescing and cleaning the data, and a set of three visualizations we created to facilitate exploration of the data. This data is meant to be useful to the broad data visualization community to help understand the evolution of the field and as an example document collection for text data visualization research.

  9. Beamforming transmission in IEEE 802.11ac under time-varying channels.

    Science.gov (United States)

    Yu, Heejung; Kim, Taejoon

    2014-01-01

    The IEEE 802.11ac wireless local area network (WLAN) standard has adopted beamforming (BF) schemes to improve spectral efficiency and throughput with multiple antennas. To design the transmit beam, a channel sounding process to feedback channel state information (CSI) is required. Due to sounding overhead, throughput increases with the amount of transmit data under static channels. Under practical channel conditions with mobility, however, the mismatch between the transmit beam and the channel at transmission time causes performance loss when transmission duration after channel sounding is too long. When the fading rate, payload size, and operating signal-to-noise ratio are given, the optimal transmission duration (i.e., packet length) can be determined to maximize throughput. The relationship between packet length and throughput is also investigated for single-user and multiuser BF modes.

  10. Fir Filters Compliant with the IEEE Standard for M Class PMU

    Directory of Open Access Journals (Sweden)

    Duda Krzysztof

    2016-12-01

    Full Text Available In this paper it is shown that M class PMU (Phasor Measurement Unit reference model for phasor estimation recommended by the IEEE Standard C37.118.1 with the Amendment 1 is not compliant with the Standard. The reference filter preserves only the limits for TVE (total vector error, and exceeds FE (frequency error and RFE (rate of frequency error limits. As a remedy we propose new filters for phasor estimation for M class PMU that are fully compliant with the Standard requirements. The proposed filters are designed: 1 by the window method; 2 as flat-top windows; or as 3 optimal min-max filters. The results for all Standard compliance tests are presented, confirming good performance of the proposed filters. The proposed filters are fixed at the nominal frequency, i.e. frequency tracking and adaptive filter tuning are not required, therefore they are well suited for application in lowcost popular PMUs.

  11. IEEE [Institute of Electrical and Electronics Engineers] standards and nuclear software quality engineering

    International Nuclear Information System (INIS)

    Daughtrey, T.

    1988-01-01

    Significant new nuclear-specific software standards have recently been adopted under the sponsorship of the American Nuclear Society and the American Society of Mechanical Engineers. The interest of the US Nuclear Regulatory Commission has also been expressed through their issuance of NUREG/CR-4640. These efforts all indicate a growing awareness of the need for thorough, referenceable expressions of the way to build in and evaluate quality in nuclear software. A broader professional perspective can be seen in the growing number of software engineering standards sponsored by the Institute of Electrical and Electronics Engineers (IEEE) Computer Society. This family of standards represents a systematic effort to capture professional consensus on quality practices throughout the software development life cycle. The only omission-the implementation phase-is treated by accepted American National Standards Institute or de facto standards for programming languages

  12. 3th IEEE/ACIS International Conference on Computer and Information Science

    CERN Document Server

    2015-01-01

    This edited book presents scientific results of the 13th IEEE/ACIS International Conference on Computer and Information Science (ICIS 2014) which was held on June 4-6, 2014 in Taiyuan, China. The aim of this conference was to bring together researchers and scientists, businessmen and entrepreneurs, teachers, engineers, computer users, and students to discuss the numerous fields of computer science and to share their experiences and exchange new ideas and information in a meaningful way. Research results about all aspects (theory, applications and tools) of computer and information science, and to discuss the practical challenges encountered along the way and the solutions adopted to solve them. The conference organizers selected the best papers from those papers accepted for presentation at the conference.  The papers were chosen based on review scores submitted by members of the program committee, and underwent further rigorous rounds of review. This publication captures 14 of the conference’s most promis...

  13. Delay efficient cooperation in public safety vehicular networks using LTE and IEEE 802.11p

    KAUST Repository

    Atat, Rachad

    2012-01-01

    Cooperative schemes for critical content distribution over vehicular networks are presented and analyzed. The first scheme is based on unicasting from the base station, whereas the second is based on threshold based multicasting. Long Term Evolution (LTE) is used for long range communications with the base station (BS) and 802.11p is considered for inter-vehicle collaboration on the short range. A high mobility environment with correlated shadowing is adopted. Both schemes are shown to outperform non-cooperative unicasting and multicasting, respectively, when the appropriate 802.11p power class is used. The first scheme achieves the best performance among the compared methods, and a practical approximation of that scheme is shown to be close to optimal performance. © 2012 IEEE.

  14. Dynamic Voltage Stability Studies using a Modified IEEE 30-Bus System

    Directory of Open Access Journals (Sweden)

    Oluwafemi Emmanuel Oni

    2016-09-01

    Full Text Available Power System stability is an essential study in the planning and operation of an efficient, economic, reliable and secure electric power system because it encompasses all the facet of power systems operations, from planning, to conceptual design stages of the project as well as during the systems operating life span. This paper presents different scenario of power system stability studies on a modified IEEE 30-bus system which is subjected to different faults conditions. A scenario whereby the longest high voltage alternating current (HVAC line is replaced with a high voltage direct current (HVDC line was implemented. The results obtained show that the HVDC line enhances system stability more compared to the contemporary HVAC line. Dynamic analysis using RMS simulation tool was used on DigSILENT PowerFactory.

  15. Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs with Extended Service Range

    Science.gov (United States)

    Choi, Woo-Yong

    2011-11-01

    In this paper, we propose the efficient reliable multicast MAC protocol by which the AP (Access Point) can transmit reliably its multicast data frames to the recipients in the AP's one-hop or two-hop transmission range. The AP uses the STAs (Stations) that are directly associated with itself as the relays for the data delivery to the remote recipients that cannot be reached directly from itself. Based on the connectivity information among the recipients, the reliable multicast MAC protocol optimizes the number of the RAK (Request for ACK) frame transmissions in a reasonable computational time. Numerical examples show that our proposed MAC protocol significantly enhances the MAC performance compared with the BMMM (Batch Mode Multicast MAC) protocol that is extended to support the recipients that are in the AP's one-hop or two-hop transmission range in IEEE 802.11 wireless LANs.

  16. Experimental video signals distribution MMF network based on IEEE 802.11 standard

    Science.gov (United States)

    Kowalczyk, Marcin; Maksymiuk, Lukasz; Siuzdak, Jerzy

    2014-11-01

    The article was focused on presentation the achievements in a scope of experimental research on transmission of digital video streams in the frame of specially realized for this purpose ROF (Radio over Fiber) network. Its construction was based on the merge of wireless IEEE 802.11 network, popularly referred as Wi-Fi, with a passive optical network PON based on multimode fibers MMF. The proposed approach can constitute interesting proposal in area of solutions in the scope of the systems monitoring extensive, within which is required covering of a large area with ensuring of a relatively high degree of immunity on the interferences transmitted signals from video IP cameras to the monitoring center and a high configuration flexibility (easily change the deployment of cameras) of such network.

  17. Mobile Device Passive Localization Based on IEEE 802.11 Probe Request Frames

    Directory of Open Access Journals (Sweden)

    Lin Sun

    2017-01-01

    Full Text Available This paper presents a novel passive mobile device localization mode based on IEEE 802.11 Probe Request frames. In this approach, the listener can discover mobile devices by receiving the Probe Request frames and localize them on his walking path. The unique location of the mobile device is estimated on a geometric diagram and right-angled walking path. In model equations, site-related parameter, that is, path loss exponent, is eliminated to make the approach site-independent. To implement unique localization, the right-angled walking path is designed and the optimal location is estimated from the optional points. The performance of our method has been evaluated inside the room, outside the room, and in outdoor scenarios. Three kinds of walking paths, for example, horizontal, vertical, and slanted, are also tested.

  18. IEEE 1394/firewire a low cost, high speed, digital serial bus

    Energy Technology Data Exchange (ETDEWEB)

    Gaunt, R.

    1997-05-01

    Does the world need yet another 1/0 bus standard? If you need fast and cheap serial video communication, then the answer is yes. As technology advances, so too must data transport mechanisms advance. You can`t expect RS-232 to support real-time digital video, and if you can`t afford expensive professional serial video interfaces, (such as Sony`s Serial Digital Interface), Firewire may be a good solution. IEEE 1394, or commonly known as Firewire, is a general purpose serial bus that meets many of the 1/0 needs of today`s video and multimedia developers. For those of you who only read the first paragraph, here`s Firewire in a nutshell: It provides a guaranteed transfer rate of 10OMbps or 20OMbps of digital data (such as video direct from camera to computer), over an inexpensive, non-proprietary serial bus. Here is a list of its features.

  19. Development of coaxial ultrasonic probe for fatty liver diagnostic system using ultrasonic velocity change

    Science.gov (United States)

    Hori, Makoto; Yokota, Daiki; Aotani, Yuhei; Kumagai, Yuta; Wada, Kenji; Matsunaka, Toshiyuki; Morikawa, Hiroyasu; Horinaka, Hiromichi

    2017-07-01

    A diagnostic system for fatty liver at an early stage is needed because fatty liver is linked to metabolic syndrome. We have already proposed a fatty liver diagnosis method based on the temperature coefficient of ultrasonic velocity. In this study, we fabricated a coaxial ultrasonic probe by integrating two kinds of transducers for warming and signal detection. The diagnosis system equipped with the coaxial probe was applied to tissue-mimicking phantoms including the fat area. The fat content rates corresponding to the set rates of the phantoms were estimated by the ultrasonic velocity-change method.

  20. Ultrasonic unit for line-by-line ultrasonic scanning of bodies

    International Nuclear Information System (INIS)

    Soldner, R.

    1978-01-01

    The ultrasonic unit for medical diagnostics operates by the sectorial scanning principle, which avoids direct coupling of the transducer head to the surface of the body. For this purpose, several transmitter/receiver units (approx. 100) are arranged on a partial ring of a circular arc and the ultrasonic beams, which can be triggered sequentially in time, are directed at a common intersection behind the ultrasonic window of the unit, i.e., outside the unit. A mechanical system is employed to set and adjust the partial ring carrying the transmitter/receiver units. (DG) [de

  1. Trans fats in New Zealand: time for labelling regulations?

    Science.gov (United States)

    Gladding, Patrick; Benatar, Jocelyne R

    2007-11-09

    Trans fats (trans fatty acids) are commonly used for deep frying in restaurants and in the fast food, snack food, fried food, and baked goods industries, often to extend the shelf life of foods. However they are widely considered to be harmful to health. Trans fats were banned in New York City restaurants from 1 July 2007, and there is growing vocal opposition to trans fats in the European Union. Denmark became the first country, in March 2003, to introduce laws regulating the content of trans fats in food (maximum of 2% of edible fats and oils). What are trans fats, what harm do they cause, and should New Zealand also consider imposing mandatory regulations on their use in food? This article explores the issues.

  2. Nuclear reactions: Science and trans-science

    International Nuclear Information System (INIS)

    Weinberg, A.M.

    1992-01-01

    This book is a collection of essays written by Weinberg over the span of his scientific and administrative career. A sound theorist, he was introduced to nuclear physics as part of the Manhattan project, and assumed administrative responsibilities during that project. His career has allowed him to make valuable contributions in a broad range of fields. These essays touch on topics of interest to him, concern to the country, and of profound import for society as it exists today. They are grouped into five sections: science and trans-science; scientific administration; strategic defense and arms control; time, energy and resources; nuclear energy

  3. TRAN-STAT: statistics for environmental studies

    International Nuclear Information System (INIS)

    Gilbert, R.O.

    1984-09-01

    This issue of TRAN-STAT discusses statistical methods for assessing the uncertainty in predictions of pollutant transport models, particularly for radionuclides. Emphasis is placed on radionuclide transport models but the statistical assessment techniques also apply in general to other types of pollutants. The report begins with an outline of why an assessment of prediction uncertainties is important. This is followed by an introduction to several methods currently used in these assessments. This in turn is followed by more detailed discussion of the methods, including examples. 43 references, 2 figures

  4. A Study of IEEE 802.15.4 Security Framework for Wireless Body Area Networks

    Directory of Open Access Journals (Sweden)

    Kyung Sup Kwak

    2011-01-01

    Full Text Available A Wireless Body Area Network (WBAN is a collection of low-power and lightweight wireless sensor nodes that are used to monitor the human body functions and the surrounding environment. It supports a number of innovative and interesting applications, including ubiquitous healthcare and Consumer Electronics (CE applications. Since WBAN nodes are used to collect sensitive (life-critical information and may operate in hostile environments, they require strict security mechanisms to prevent malicious interaction with the system. In this paper, we first highlight major security requirements and Denial of Service (DoS attacks in WBAN at Physical, Medium Access Control (MAC, Network, and Transport layers. Then we discuss the IEEE 802.15.4 security framework and identify the security vulnerabilities and major attacks in the context of WBAN. Different types of attacks on the Contention Access Period (CAP and Contention Free Period (CFP parts of the superframe are analyzed and discussed. It is observed that a smart attacker can successfully corrupt an increasing number of GTS slots in the CFP period and can considerably affect the Quality of Service (QoS in WBAN (since most of the data is carried in CFP period. As we increase the number of smart attackers the corrupted GTS slots are eventually increased, which prevents the legitimate nodes to utilize the bandwidth efficiently. This means that the direct adaptation of IEEE 802.15.4 security framework for WBAN is not totally secure for certain WBAN applications. New solutions are required to integrate high level security in WBAN.

  5. A study of IEEE 802.15.4 security framework for wireless body area networks.

    Science.gov (United States)

    Saleem, Shahnaz; Ullah, Sana; Kwak, Kyung Sup

    2011-01-01

    A Wireless Body Area Network (WBAN) is a collection of low-power and lightweight wireless sensor nodes that are used to monitor the human body functions and the surrounding environment. It supports a number of innovative and interesting applications, including ubiquitous healthcare and Consumer Electronics (CE) applications. Since WBAN nodes are used to collect sensitive (life-critical) information and may operate in hostile environments, they require strict security mechanisms to prevent malicious interaction with the system. In this paper, we first highlight major security requirements and Denial of Service (DoS) attacks in WBAN at Physical, Medium Access Control (MAC), Network, and Transport layers. Then we discuss the IEEE 802.15.4 security framework and identify the security vulnerabilities and major attacks in the context of WBAN. Different types of attacks on the Contention Access Period (CAP) and Contention Free Period (CFP) parts of the superframe are analyzed and discussed. It is observed that a smart attacker can successfully corrupt an increasing number of GTS slots in the CFP period and can considerably affect the Quality of Service (QoS) in WBAN (since most of the data is carried in CFP period). As we increase the number of smart attackers the corrupted GTS slots are eventually increased, which prevents the legitimate nodes to utilize the bandwidth efficiently. This means that the direct adaptation of IEEE 802.15.4 security framework for WBAN is not totally secure for certain WBAN applications. New solutions are required to integrate high level security in WBAN.

  6. Characterization methods for ultrasonic test systems

    International Nuclear Information System (INIS)

    Busse, L.J.; Becker, F.L.; Bowey, R.E.; Doctor, S.R.; Gribble, R.P.; Posakony, G.J.

    1982-07-01

    Methods for the characterization of ultrasonic transducers (search units) and instruments are presented. The instrument system is considered as three separate components consisting of a transducer, a receiver-display, and a pulser. The operation of each component is assessed independently. The methods presented were chosen because they provide the greatest amount of information about component operation and were not chosen based upon such conditions as cost, ease of operation, field implementation, etc. The results of evaluating a number of commercially available ultrasonic test instruments are presented

  7. Absorption and dispersion of ultrasonic waves

    CERN Document Server

    Herzfeld, Karl F; Massey, H S W; Brueckner, Keith A

    1959-01-01

    Absorption and Dispersion of Ultrasonic Waves focuses on the influence of ultrasonics on molecular processes in liquids and gases, including hydrodynamics, energy exchange, and chemical reactions. The book first offers information on the Stokes-Navier equations of hydrodynamics, as well as equations of motion, viscosity, formal introduction of volume viscosity, and linearized wave equation for a nonviscous fluid. The manuscript then ponders on energy exchange between internal and external degrees of freedom as relaxation phenomenon; effect of slow energy exchange on sound propagation; differe

  8. Ultrasonic methods in solid state physics

    CERN Document Server

    Truell, John; Elbaum, Charles

    1969-01-01

    Ultrasonic Methods in Solid State Physics is devoted to studies of energy loss and velocity of ultrasonic waves which have a bearing on present-day problems in solid-state physics. The discussion is particularly concerned with the type of investigation that can be carried out in the megacycle range of frequencies from a few megacycles to kilomegacycles; it deals almost entirely with short-duration pulse methods rather than with standing-wave methods. The book opens with a chapter on a classical treatment of wave propagation in solids. This is followed by separate chapters on methods and techni

  9. Ultrasonic process for detoxification of groundwater

    International Nuclear Information System (INIS)

    Wu, Jiann M.; Huang, H.S.; Livengood, C.D.

    1991-01-01

    In this paper, we present the results of an investigation of the ultrasonic irradiation of carbon tetrachloride at various pH values, temperatures, and power intensities. Kinetic data and selected chemical mechanism are discussed and proposed. To study oxidant efficiency, chemical oxidants, such as hydrogen peroxide, are also considered. This work is part of a project entitled ''Ultrasonic Process for Detoxification of Groundwater and Soil,'' sponsored by the US Department of Energy, Office of Technology Development, to develop an innovative process for the effective destruction of chlorinated organics in soil and groundwater

  10. Ultrasonic Ranging System With Increased Resolution

    Science.gov (United States)

    Meyer, William E.; Johnson, William G.

    1987-01-01

    Master-oscillator frequency increased. Ultrasonic range-measuring system with 0.1-in. resolution provides continuous digital display of four distance readings, each updated four times per second. Four rangefinder modules in system are modified versions of rangefinder used for automatic focusing in commercial series of cameras. Ultrasonic pulses emitted by system innocuous to both people and equipment. Provides economical solutions to such distance-measurement problems as posed by boats approaching docks, truck backing toward loading platform, runway-clearance readout for tail of airplane with high angle attack, or burglar alarm.

  11. Control of hydrodynamic cavitation using ultrasonic

    Science.gov (United States)

    Chatterjee, Dhiman; Arakeri, Vijay H.

    2003-11-01

    Hydrodynamic cavitation is known to have many harmful effects like surface damage and generation of noise. We investigated the use of ultrasonics to control traveling bubble cavitation. Ultrasonic pressure field, produced by a piezoelectric crystal, was applied to modify the nuclei size distribution. Effects of continuous-wave (CW) and pulsed excitations were studied. At low dissolved gas content the CW-mode performed better than the pulsed one, whereas for high gas content the pulsed one was more effective. The dominant mechanisms were Bjerknes force and rectified diffusion in these two cases. Simultaneous excitation by two crystals in CW and pulsed modes was seen to control cavitation better.

  12. Structural modification of trans-cinnamic acid using Colletotrichum acutatum

    OpenAIRE

    Velasco B., Rodrigo; Gil G., Jesús H.; García P., Carlos M.; Durango R., Diego L.

    2012-01-01

    The biotransformation of trans-cinnamic acid by whole cells of the Colombian native phytopathogenic fungus Colletotrichum acutatum was studied. Initially, fungitoxicity of this compound against C. acutatum was evaluated; trans-cinnamic acid exhibited a moderate to weak toxicity against the microorganism and apparently a detoxification mechanism was present. Then, in order to study such mechanism and explore the capacity of this fungus to biotransform trans-cinnamic acid into value-added produ...

  13. Trans-nationalisation Processes in the Ukrainian Economy

    OpenAIRE

    Bolharova Natalya K.; Panevnyk Tetyana M.

    2013-01-01

    The article considers main processes of trans-nationalisation of Ukrainian economy, identifies specific features of trans-national production and explains some theoretical aspects of these issues. It provides main stages of theoretical comprehension of activity of trans-national corporations (TNC), specific features of the theory of competitive advantages of TNC and specifies the basic ones of them. The article conducts analysis of flows of direct foreign investments into the Ukrainian econom...

  14. Trans*Forming College Masculinities: Carving out Trans*Masculine Pathways through the Threshold of Dominance

    Science.gov (United States)

    Jourian, T. J.

    2017-01-01

    Men and masculinities studies are gaining prominence in higher education literature, illuminating how cisgender college men understand and grapple with masculinity. Additionally, the increased visibility of trans* students has fueled the expanding scholarship and attention to their experiences, often however centering on white gender-conforming…

  15. Trans advanced surface laser ablation (TransPRK) outcomes using SmartPulseTechnology.

    Science.gov (United States)

    Aslanides, Ioannis M; Kymionis, George D

    2017-02-01

    To evaluate early visual rehabilitation, post-operative pain, epithelial healing and haze after transepithelial photorefractive keratectomy (TransPRK) using the SmartPulseTechnology (SPT) of Schwind Amaris (Schwind eye-tech-solutions GmbH, Kleinostheim, Germany). This was a retrospective comparative evaluation of a cohort of myopic patients undergoing TransPRK with SPT (group 1), with one matched control group that underwent conventional TransPRK (group 2). All cases had a 6-month post-operative follow-up including visual acuity and slit-lamp examination. Subjective evaluation of pain was recorded post-operatively. 49 eyes of 25 patients in group 1 and 40 eyes of 20 patients in group 2 were enrolled. The patients' visual rehabilitation was significantly faster in group 1, one day and one week post-operatively (P0.05). TransPRK using SPT provides promising results in the early post-operative period. Visual rehabilitation, re-epithelialization and pain were faster in the early post-operative period in group 1 in comparison with group 2. Haze formation was not significantly different between the two groups; however, it was consistently less in group 1. Copyright © 2016 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

  16. Trans-nationalizing the African Public Sphere: What Role for Trans ...

    African Journals Online (AJOL)

    seriane.camara

    2011-03-09

    Mar 9, 2011 ... At a time when the notion of 'trans-national public spheres' is gaining .... ple refer specifically to the language and its speakers in Senegal and Mauri- .... of the Pulaar language and the improvement of the social and economic.

  17. A trans European Union difference in the decline in trans fatty acids in popular foods

    DEFF Research Database (Denmark)

    Stender, Steen; Astrup, Arne; Dyerberg, Jørn

    2012-01-01

    To minimise the intake of industrial trans fatty acids (I-TFA) some countries have introduced labelling, while others have introduced legislative limits on the content of I-TFA in food. However, most countries still rely on food producers to voluntarily reduce the I-TFA content in food. The objec...

  18. Spectroscopic and density functional theory studies of trans-3-(trans-4-imidazolyl)acrylic acid.

    Science.gov (United States)

    Arjunan, V; Remya, P; Sathish, U; Rani, T; Mohan, S

    2014-08-14

    The structural parameters, thermodynamic properties and vibrational frequencies of the optimised geometry of trans-3-(trans-4-imidazolyl)acrylic acid have been determined from B3LYP methods with 6-311++G(**) and cc-pVTZ basis sets. The effects of substituents (acrylyl group) on the imidazole vibrational frequencies are analysed. The vibrational frequencies of the fundamental modes of trans-3-(trans-4-imidazolyl)acrylic acid have been precisely assigned and analysed and the theoretical results are compared with the experimental vibrations. (1)H and (13)C NMR isotropic chemical shifts are calculated and the assignments made are compared with the experimental values. The energies of important MO's of the compound are also determined from DFT method. The total electron density and electrostatic potential of the compound are determined by natural bond orbital analysis. Various reactivity and selectivity descriptors such as chemical hardness, chemical potential, softness, electrophilicity, nucleophilicity and the appropriate local quantities employing natural population analysis (NPA) are calculated. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. [CONTENT OF TRANS FATTY ACIDS IN FOOD PRODUCTS IN SPAIN].

    Science.gov (United States)

    Robledo de Dios, Teresa; Dal Re Saavedra, M Ángeles; Villar Villalba, Carmen; Pérez-Farinós, Napoleón

    2015-09-01

    trans fatty acids are associated to several health disorders, as ischemic heart disease or diabetes mellitus. to assess the content of trans fatty acids in products in Spain, and the percentage of trans fatty acids respecting total fatty acids. 443 food products were acquired in Spain, and they were classified into groups. The content in fatty acids was analyzed using gas chromatography. Estimates of central tendency and variability of the content of trans fatty acids in each food group were computed (in g of trans fatty acids/100 g of product). The percentage of trans fatty acids respecting total fatty acids was calculated in each group. 443 products were grouped into 42 groups. Median of trans fatty acids was less than 0.55 g / 100 g of product in all groups except one. 83 % of groups had less than 2 % of trans fatty acids, and 71 % of groups had less than 1 %. the content of trans fatty acids in Spain is low, and it currently doesn't play a public health problem. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

  20. Is there such a thing as Tech Trans?

    DEFF Research Database (Denmark)

    Helms, Niels Henrik

    2009-01-01

    This short paper is an attempt to start a discussion on some basic issues within the concept of Tech Trans especially the relationship between flow and structure within the concept. The background to this paper is first of all an academic interest in the relationship between flow and structure...... explores the concept of Tech Trans, show rooms and innovation systems, and it suggests that the notion of Tech Trans should be defined in the fix point of vertical and horizontal innovation. Finally this paper suggests a mathematical formula for evaluating Tech Trans....

  1. Attention modulates trans-saccadic integration.

    Science.gov (United States)

    Stewart, Emma E M; Schütz, Alexander C

    2018-01-01

    With every saccade, humans must reconcile the low resolution peripheral information available before a saccade, with the high resolution foveal information acquired after the saccade. While research has shown that we are able to integrate peripheral and foveal vision in a near-optimal manner, it is still unclear which mechanisms may underpin this important perceptual process. One potential mechanism that may moderate this integration process is visual attention. Pre-saccadic attention is a well documented phenomenon, whereby visual attention shifts to the location of an upcoming saccade before the saccade is executed. While it plays an important role in other peri-saccadic processes such as predictive remapping, the role of attention in the integration process is as yet unknown. This study aimed to determine whether the presentation of an attentional distractor during a saccade impaired trans-saccadic integration, and to measure the time-course of this impairment. Results showed that presenting an attentional distractor impaired integration performance both before saccade onset, and during the saccade, in selected subjects who showed integration in the absence of a distractor. This suggests that visual attention may be a mechanism that facilitates trans-saccadic integration. Copyright © 2017 The Author(s). Published by Elsevier Ltd.. All rights reserved.

  2. Mathematical modeling of a radio-frequency path for IEEE 802.11ah based wireless sensor networks

    Science.gov (United States)

    Tyshchenko, Igor; Cherepanov, Alexander; Dmitrii, Vakhnin; Popova, Mariia

    2017-09-01

    This article discusses the process of creating the mathematical model of a radio-frequency path for an IEEE 802.11ah based wireless sensor networks using M atLab Simulink CAD tools. In addition, it describes occurring perturbing effects and determining the presence of a useful signal in the received mixture.

  3. Spectrum-efficient multi-channel design for coexisting IEEE 802.15.4 networks: A stochastic geometry approach

    KAUST Repository

    Elsawy, Hesham

    2014-07-01

    For networks with random topologies (e.g., wireless ad-hoc and sensor networks) and dynamically varying channel gains, choosing the long term operating parameters that optimize the network performance metrics is very challenging. In this paper, we use stochastic geometry analysis to develop a novel framework to design spectrum-efficient multi-channel random wireless networks based on the IEEE 802.15.4 standard. The proposed framework maximizes both spatial and time domain frequency utilization under channel gain uncertainties to minimize the number of frequency channels required to accommodate a certain population of coexisting IEEE 802.15.4 networks. The performance metrics are the outage probability and the self admission failure probability. We relax the single channel assumption that has been used traditionally in the stochastic geometry analysis. We show that the intensity of the admitted networks does not increase linearly with the number of channels and the rate of increase of the intensity of the admitted networks decreases with the number of channels. By using graph theory, we obtain the minimum required number of channels to accommodate a certain intensity of coexisting networks under a self admission failure probability constraint. To this end, we design a superframe structure for the coexisting IEEE 802.15.4 networks and a method for time-domain interference alignment. © 2002-2012 IEEE.

  4. Real-life IT architecture design reports and their relation to IEEE Std 1471 stakeholders and concerns

    NARCIS (Netherlands)

    van Vliet, H.; Koning, H.

    2006-01-01

    Architectural designs are an important means to manage the development and deployment of information technology (IT). Much debate has been going on about a proper definition of architecture in IT and about how to describe it. In 2000, the IEEE Std 1471 proposed a model of an architecture description

  5. Architectural and Functional Design and Evaluation of E-Learning VUIS Based on the Proposed IEEE LTSA Reference Model.

    Science.gov (United States)

    O'Droma, Mairtin S.; Ganchev, Ivan; McDonnell, Fergal

    2003-01-01

    Presents a comparative analysis from the Institute of Electrical and Electronics Engineers (IEEE) Learning Technology Standards Committee's (LTSC) of the architectural and functional design of e-learning delivery platforms and applications, e-learning course authoring tools, and learning management systems (LMSs), with a view of assessing how…

  6. Analyzing the Engineering Educational Research in Spain: A Global Vision through the Awards of CESEI-IEEE

    Science.gov (United States)

    Plaza, I.; Arcega, F.; Castro, M.; Llamas, M.

    2011-01-01

    CESEI is the acronym of the Spanish Chapter of the Education Society of IEEE (the Institute of Electric and Electronics Engineers). Every year, the CESEI awards a prize for the best doctoral thesis and FDP (final (master) degree projects) about education. The thesis or the project must be developed in the areas of electrical engineering,…

  7. Analysis of Radio communication solutions in small and isolated communities under the IEEE 802.22 standard

    OpenAIRE

    Arroyo Arzubi, Alejandro; Castro Lechtaler, Antonio; Foti, Antonio Roberto; Fusario, Rubén J.; García Guibout, Jorge; Sens, Lorena

    2013-01-01

    In recent years the use of wireless communications has increased significantly. Rural communities without cable network communication have found a solution in wireless technologies. Based on previous fieldwork, this paper analyzes software development of integration based technologies for communication equipment. It focuses on the feasibility of the IEEE 802.22 standard as a solution to the wireless problem.

  8. AVSS 2007: IEEE International Conference onAdvanced Video and Signal based Surveillance, London, UK, September 2007

    DEFF Research Database (Denmark)

    Fihl, Preben

    This technical report will cover the participation in the IEEE International Conference on Advanced Video and Signal based Surveillance in September 2007. The report will give a concise description of the most relevant topics presented at the conference, focusing on the work related to the HERMES...... project and human motion and action recognition. Our contribution to the conference will also be described....

  9. Low-cost RAU with Optical Power Supply Used in a Hybrid RoF IEEE 802.11 Network

    Science.gov (United States)

    Kowalczyk, M.; Siuzdak, J.

    2014-09-01

    The paper presents design and implementation of a low-cost RAU (Remote Antenna Unit) device. It was designed to work in a hybrid Wi-Fi/optical network based on the IEEE 802.11b/g standard. An unique feature of the device is the possibility of optical power supply.

  10. Open Data for Global Multimodal Land Use Classification: Outcome of the 2017 IEEE GRSS Data Fusion Contest

    NARCIS (Netherlands)

    Yokoya, Naoto; Ghamisi, Pedram; Xia, Junshi; Sukhanov, Sergey; Heremans, Roel; Tankoyeu, Ivan; Bechtel, Benjamin; Saux, Le Bertrand; Moser, Gabriele; Tuia, Devis

    2018-01-01

    In this paper, we present the scientific outcomes of the 2017 Data Fusion Contest organized by the Image Analysis and Data Fusion Technical Committee of the IEEE Geoscience and Remote Sensing Society. The 2017 Contest was aimed at addressing the problem of local climate zones classification based on

  11. Analysis of Ultrasonic Transmitted Signal for Apple using Wavelet Transform

    International Nuclear Information System (INIS)

    Kim, Ki Bok; Lee, Sang Dae; Choi, Man Yong; Kim, Man Soo

    2005-01-01

    This study was conducted to analyze the ultrasonic transmitted signal for apple using wavelet transform. Fruit consists of nonlinear visco-elastic properties such as flesh, an ovary and rind and lienee most ultrasonic wave is attenuated and its frequency is shifted during passing the fruit. Thus it is not easy to evaluate the internal quality of the fruit using typical ultrasonic parameters such as wave velocity, attenuation, and frequency spectrum. The discrete wavelet transform was applied to the ultrasonic transmitted signal for apple. The magnitude of the first peak frequency of the wavelet basis from the ultrasonic transmitted signal showed a close correlation to the storage time of apple

  12. Homologous SV40 RNA trans-splicing: Special case or prime example of viral RNA trans-splicing?

    Directory of Open Access Journals (Sweden)

    Sushmita Poddar

    2014-06-01

    Full Text Available To date the Simian Virus 40 (SV40 is the only proven example of a virus that recruits the mechanism of RNA trans-splicing to diversify its sequences and gene products. Thereby, two identical viral transcripts are efficiently joined by homologous trans-splicing triggering the formation of a highly transforming 100 kDa super T antigen. Sequences of other viruses including HIV-1 and the human adenovirus type 5 were reported to be involved in heterologous trans-splicing towards cellular or viral sequences but the meaning of these events remains unclear. We computationally and experimentally investigated molecular features associated with viral RNA trans-splicing and identified a common pattern: Viral RNA trans-splicing occurs between strong cryptic or regular viral splice sites and strong regular or cryptic splice sites of the trans-splice partner sequences. The majority of these splice sites are supported by exonic splice enhancers. Splice sites that could compete with the trans-splicing sites for cis-splice reactions are weaker or inexistent. Finally, all but one of the trans-splice reactions seem to be facilitated by one or more complementary binding domains of 11 to 16 nucleotides in length which, however occur with a statistical probability close to one for the given length of the involved sequences. The chimeric RNAs generated via heterologous viral RNA trans-splicing either did not lead to fusion proteins or led to proteins of unknown function. Our data suggest that distinct viral RNAs are highly susceptible to trans-splicing and that heterologous viral trans-splicing, unlike homologous SV40 trans-splicing, represents a chance event.

  13. Ultrasonic Tomography Imaging for Liquid-Gas Flow Measurement

    Directory of Open Access Journals (Sweden)

    Muhammad Jaysuman PUSPPANATHAN

    2013-01-01

    Full Text Available This research was carried out to measure two-phase liquid – gas flow regime by using a dual functionality ultrasonic transducer. Comparing to the common separated transmitter–receiver ultrasonic pairs transducer, the dual functionality ultrasonic transceiver is capable to produce the same measurable results hence further improvises and contributes to the hardware design improvement and system accuracy. Due to the disadvantages and the limitations of the separated ultrasonic transmitter–receiver pair, this paper presents a non-invasive ultrasonic tomography system using ultrasonic transceivers as an alternative approach. Implementation of ultrasonic transceivers, electronic measurement circuits, data acquisition system and suitable image reconstruction algorithms, the measurement of a liquid/gas flow was realized.

  14. Ultrasonic Low-Friction Containment Plate for Thermal and Ultrasonic Stir Weld Processes

    Science.gov (United States)

    Graff, Karl; Short, Matt

    2013-01-01

    The thermal stir welding (TSW) process is finding applications in fabrication of space vehicles. In this process, workpieces to be joined by TSW are drawn, by heavy forces, between "containment plates," past the TSW tool that then causes joining of the separate plates. It is believed that the TSW process would be significantly improved by reducing the draw force, and that this could be achieved by reducing the friction forces between the workpieces and containment plates. Based on use of high-power ultrasonics in metal forming processes, where friction reduction in drawing dies has been achieved, it is believed that ultrasonic vibrations of the containment plates could achieve similar friction reduction in the TSW process. By applying ultrasonic vibrations to the containment plates in a longitudinal vibration mode, as well as by mounting and holding the containment plates in a specific manner such as to permit the plates to acoustically float, friction between the metal parts and the containment plates is greatly reduced, and so is the drawing force. The concept was to bring in the ultrasonics from the sides of the plates, permitting the ultrasonic hardware to be placed to the side, away from the equipment that contains the thermal stir tooling and that applies clamping forces to the plates. Tests demonstrated that one of the major objectives of applying ultrasonics to the thermal stir system, that of reducing draw force friction, should be achievable on a scaled-up system.

  15. Radial vibration and ultrasonic field of a long tubular ultrasonic radiator.

    Science.gov (United States)

    Shuyu, Lin; Zhiqiang, Fu; Xiaoli, Zhang; Yong, Wang; Jing, Hu

    2013-09-01

    The radial vibration of a metal long circular tube is studied analytically and its electro-mechanical equivalent circuit is obtained. Based on the equivalent circuit, the radial resonance frequency equation is derived. The theoretical relationship between the radial resonance frequency and the geometrical dimensions is studied. Finite element method is used to simulate the radial vibration and the radiated ultrasonic field and the results are compared with those from the analytical method. It is concluded that the radial resonance frequency for a solid metal rod is larger than that for a metal tube with the same outer radius. The radial resonance frequencies from the analytical method are in good agreement with those from the numerical method. Based on the acoustic field analysis, it is concluded that the long metal tube with small wall thickness is superior to that with large wall thickness in producing radial vibration and ultrasonic radiation. Therefore, it is expected to be used as an effective radial ultrasonic radiator in ultrasonic sewage treatment, ultrasonic antiscale and descaling and other ultrasonic liquid handling applications. Copyright © 2013 Elsevier B.V. All rights reserved.

  16. Ultrasonic sensor for sodium perspective device

    International Nuclear Information System (INIS)

    Ogawa, Fujio; Onuki, Koji.

    1995-01-01

    The present invention concerns an ultrasonic wave sensor for a sodium perspective device disposed in an FBR type reactor, which can change the directing angle of the ultrasonic sensor irrespective of the external conditions in liquid sodium. Namely, the sensor comprises (1) a sensor main body, (2) a diaphragm disposed on an oscillating surface of ultrasonic waves generated from the sensor main body, (3) a pressurizing and depressurizing nozzle connected to the sensor main body, and (4) a pressure detector disposed to these nozzles. A gas is charged/discharged to and from the sensor main body to control a gas pressure in the main body. If the gas pressure is made higher, the diaphragm is deformed convexly. If the gas pressure is lowered, the diaphragm is deformed concavely. The directing angle is greater when it is deformed a convexly, and it is smaller when it is deformed concavely. Accordingly, ultrasonic wave receiving/sending range in the sodium can be varied optionally by controlling the gas pressure in the main body. (I.S.)

  17. Development of ultrasonic instrument 'UT1000 Series'

    International Nuclear Information System (INIS)

    Ogura, Yukio; Ikeda, Toshimichi

    1984-01-01

    The ultrasonic flaw detectors with 'A-scope indication' have been frequently used as the means for confirming the soundness of structures and equipments, but there are problems in their operational, quantifying and recording capabilities. Recently, the digital ultrasonic measuring instrument of touch panel type ''UT 1000 Series'' has been developed, which resolves these problems by a single effort. This measuring instrument is that of portable type, which gives the digital output of measured results in real time only by lightly touching the peak point of an echo on the Brown tube. This instrument contains the rich software for measurement, and can measure the positions and dimensions of defects and the pressure on contact surfaces with high accuracy. 'A-scope indication' is the indication with an oscilloscope taking the intensity of echo and the propagation time of ultrasonic waves on the ordinate and abscissa, respectively. There are three types of the instrument, that is, for detecting defects, for measuring contact surface pressure and for both purposes. The size of the instrument is 240 mm width, 350 mm length and 175 mm height, and the weight is 8.5 kgf. The specification, function and features of the ultrasonic flaw detector, touch panel, gain setter, key board, microcomputer and others are reported. (Kako, I.)

  18. Ultrasonic attenuation in rare-earth monoarsenides

    Indian Academy of Sciences (India)

    2015-11-27

    Home; Journals; Pramana – Journal of Physics; Volume 86; Issue 6. Ultrasonic attenuation in rare-earth monoarsenides .... Proceedings of the International Workshop/Conference on Computational Condensed Matter Physics and Materials Science (IWCCMP-2015). Posted on November 27, 2015. Guest Editors: Anurag ...

  19. An ultrasonic waveguide for nuclear power plants

    International Nuclear Information System (INIS)

    Watkins, R.D.; Gillespie, A.B.; Deighton, M.O.; Pike, R.B.

    1983-01-01

    The value of ultrasonic techniques in nuclear plants is well established. However, in most cases nuclear power plants present an extremely hostile environment for an ultrasonic transducer. The paper presents a novel technique for introducing an ultrasound into hostile liquid environments using a new form of ultrasonic waveguide. Using this approach, a standard transducer arrangement is sited in a hospitable area and conveys the ultrasound along the guide to the required beam-emission collection position. The design of a single-mode ultrasonic waveguide is described. The ultrasound is conveyed along a stainless steel strip of rectangular cross-section. The transference of energy between the strip and the liquid is achieved through a highly efficient mode-conversion process. This process overcomes the usual problems of mis-match of acoustic impedances of stainless steel and liquids, and also produces a highly collimated beam of ultrasound. Tests of a 10-m-long waveguide using these techniques are described, achieving signal-to-noise ratios in the region of 40 dB. (author)

  20. Coded ultrasonic remote control without batteries

    International Nuclear Information System (INIS)

    Gerhardy, C; Burlage, K; Schomburg, W K

    2009-01-01

    A concept for battery-less remote controls has been developed based on mechanically actuated beams and micro whistles generating ultrasound signals. These signals need to be frequency or time coded to increase the number of signals which can be distinguished from each other and environmental ultrasound. Several designs for generating coded ultrasonic signals have been investigated