A systematic method for identifying vital areas at complex nuclear facilities.

Energy Technology Data Exchange (ETDEWEB)

Beck, David Franklin; Hockert, John

2005-05-01

Identifying the areas to be protected is an important part of the development of measures for physical protection against sabotage at complex nuclear facilities. In June 1999, the International Atomic Energy Agency published INFCIRC/225/Rev.4, 'The Physical Protection of Nuclear Material and Nuclear Facilities.' This guidance recommends that 'Safety specialists, in close cooperation with physical protection specialists, should evaluate the consequences of malevolent acts, considered in the context of the State's design basis threat, to identify nuclear material, or the minimum complement of equipment, systems or devices to be protected against sabotage.' This report presents a structured, transparent approach for identifying the areas that contain this minimum complement of equipment, systems, and devices to be protected against sabotage that is applicable to complex nuclear facilities. The method builds upon safety analyses to develop sabotage fault trees that reflect sabotage scenarios that could cause unacceptable radiological consequences. The sabotage actions represented in the fault trees are linked to the areas from which they can be accomplished. The fault tree is then transformed (by negation) into its dual, the protection location tree, which reflects the sabotage actions that must be prevented in order to prevent unacceptable radiological consequences. The minimum path sets of this fault tree dual yield, through the area linkage, sets of areas, each of which contains nuclear material, or a minimum complement of equipment, systems or devices that, if protected, will prevent sabotage. This method also provides guidance for the selection of the minimum path set that permits optimization of the trade-offs among physical protection effectiveness, safety impact, cost and operational impact.

Identifying Areas of Primary Care Shortage in Urban Ohio

Directory of Open Access Journals (Sweden)

Hsin-Chung Liao

Full Text Available ABSTRACT: This study considers both spatial and a-spatial variables in examining accessibility to primary healthcare in the three largest urban areas of Ohio (Cleveland, Columbus, and Cincinnati. Spatial access emphasizes the importance of geographic barriers between individuals and primary care physicians, while a-spatial variables include non-geographic barriers or facilitators such as age, sex, race, income, social class, education, living conditions and language skills. Population and socioeconomic data were obtained from the 2000 Census, and primary care physician data for 2008 was provided by the Ohio Medical Board. We first implemented a two-step method based on a floating catchment area using Geographic Information Systems to measure spatial accessibility in terms of 30-minute travel times. We then used principal component analysis to group various socio-demographic variables into three groups: (1 socioeconomic disadvantages, (2 living conditions, and (3 healthcare needs. Finally, spatial and a-spatial variables were integrated to identify areas with poor access to primary care in Cleveland, Columbus, and Cincinnati. KEYWORDS: Geographic information systems, healthcare access, spatial accessibility, primary care shortage areas

An Automated Self-Learning Quantification System to Identify Visible Areas in Capsule Endoscopy Images.

Science.gov (United States)

Hashimoto, Shinichi; Ogihara, Hiroyuki; Suenaga, Masato; Fujita, Yusuke; Terai, Shuji; Hamamoto, Yoshihiko; Sakaida, Isao

2017-08-01

Visibility in capsule endoscopic images is presently evaluated through intermittent analysis of frames selected by a physician. It is thus subjective and not quantitative. A method to automatically quantify the visibility on capsule endoscopic images has not been reported. Generally, when designing automated image recognition programs, physicians must provide a training image; this process is called supervised learning. We aimed to develop a novel automated self-learning quantification system to identify visible areas on capsule endoscopic images. The technique was developed using 200 capsule endoscopic images retrospectively selected from each of three patients. The rate of detection of visible areas on capsule endoscopic images between a supervised learning program, using training images labeled by a physician, and our novel automated self-learning program, using unlabeled training images without intervention by a physician, was compared. The rate of detection of visible areas was equivalent for the supervised learning program and for our automatic self-learning program. The visible areas automatically identified by self-learning program correlated to the areas identified by an experienced physician. We developed a novel self-learning automated program to identify visible areas in capsule endoscopic images.

Opuntia in Mexico: identifying priority areas for conserving biodiversity in a multi-use landscape.

Directory of Open Access Journals (Sweden)

Patricia Illoldi-Rangel

Full Text Available BACKGROUND: México is one of the world's centers of species diversity (richness for Opuntia cacti. Yet, in spite of their economic and ecological importance, Opuntia species remain poorly studied and protected in México. Many of the species are sparsely but widely distributed across the landscape and are subject to a variety of human uses, so devising implementable conservation plans for them presents formidable difficulties. Multi-criteria analysis can be used to design a spatially coherent conservation area network while permitting sustainable human usage. METHODS AND FINDINGS: Species distribution models were created for 60 Opuntia species using MaxEnt. Targets of representation within conservation area networks were assigned at 100% for the geographically rarest species and 10% for the most common ones. Three different conservation plans were developed to represent the species within these networks using total area, shape, and connectivity as relevant criteria. Multi-criteria analysis and a metaheuristic adaptive tabu search algorithm were used to search for optimal solutions. The plans were built on the existing protected areas of México and prioritized additional areas for management for the persistence of Opuntia species. All plans required around one-third of México's total area to be prioritized for attention for Opuntia conservation, underscoring the implausibility of Opuntia conservation through traditional land reservation. Tabu search turned out to be both computationally tractable and easily implementable for search problems of this kind. CONCLUSIONS: Opuntia conservation in México require the management of large areas of land for multiple uses. The multi-criteria analyses identified priority areas and organized them in large contiguous blocks that can be effectively managed. A high level of connectivity was established among the prioritized areas resulting in the enhancement of possible modes of plant dispersal as well as

Identifying optimal areas for REDD intervention: East Kalimantan, Indonesia as a case study

International Nuclear Information System (INIS)

Harris, Nancy L; Petrova, Silvia; Brown, Sandra; Stolle, Fred

2008-01-01

International discussions on reducing emissions from deforestation and degradation (REDD) as a greenhouse gas (GHG) abatement strategy are ongoing under the United Nations Framework Convention on Climate Change (UNFCCC). In the light of these discussions, it behooves countries to be able to determine the relative likelihood of deforestation over a landscape and perform a first order estimation of the potential reduction in GHGs associated with various protection scenarios. This would allow countries to plan their interventions accordingly to maximize carbon benefits, alongside other environmental and socioeconomic benefits, because forest protection programs might be chosen in places where the perceived threat of deforestation is high whereas in reality the threat is low. In this case study, we illustrate a method for creating deforestation threat maps and estimating potential reductions in GHGs from eighteen protected areas in East Kalimantan, Indonesia, that would occur if protection of these areas was well enforced. Results from our analysis indicate that a further 230 720 ha of East Kalimantan's forest area would be lost and approximately 305 million t CO 2 would be emitted from existing protected areas between 2003 and 2013 if the historical rate of deforestation continued unabated. In other words, the emission of 305 million t CO 2 into the atmosphere would be avoided during this period if protection of the existing areas was well enforced. At a price of $4 per ton of CO 2 (approximate price on the Chicago Climate Exchange in August 2008), this represents an estimated gross income stream of about $120 million per year. We also identified additional areas with high carbon stocks under high deforestation threat that would be important to protect if the carbon benefits of avoided deforestation activities are to be maximized in this region

Identifying and assessing ecotourism visitor impacts at selected protected areas in Costa Rica and Belize

Science.gov (United States)

Farrell, T.A.; Marion, J.L.

2001-01-01

Protected area visitation is an important component of ecotourism, and as such, must be sustainable. However, protected area visitation may degrade natural resources, particularly in areas of concentrated visitor activities like trails and recreation sites. This is an important concern in ecotourism destinations such as Belize and Costa Rica, because they actively promote ecotourism and emphasize the pristine qualities of their natural resources. Research on visitor impacts to protected areas has many potential applications in protected area management, though it has not been widely applied in Central and South America. This study targeted this deficiency through manager interviews and evaluations of alternative impact assessment procedures at eight protected areas in Belize and Costa Rica. Impact assessment procedures included qualitative condition class systems, ratings systems, and measurement-based systems applied to trails and recreation sites. The resulting data characterize manager perceptions of impact problems, document trail and recreation site impacts, and provide examples of inexpensive, efficient and effective rapid impact assessment procedures. Interview subjects reported a variety of impacts affecting trails, recreation sites, wildlife, water, attraction features and other resources. Standardized assessment procedures were developed and applied to record trail and recreation site impacts. Impacts affecting the study areas included trail proliferation, erosion and widening, muddiness on trails, vegetation cover loss, soil and root exposure, and tree damage on recreation sites. The findings also illustrate the types of assessment data yielded by several alternative methods and demonstrate their utility to protected area managers. The need for additional rapid assessment procedures for wildlife, water, attraction feature and other resource impacts was also identified.

Use of demand for and spatial flow of ecosystem services to identify priority areas.

Science.gov (United States)

Verhagen, Willem; Kukkala, Aija S; Moilanen, Atte; van Teeffelen, Astrid J A; Verburg, Peter H

2017-08-01

Policies and research increasingly focus on the protection of ecosystem services (ESs) through priority-area conservation. Priority areas for ESs should be identified based on ES capacity and ES demand and account for the connections between areas of ES capacity and demand (flow) resulting in areas of unique demand-supply connections (flow zones). We tested ways to account for ES demand and flow zones to identify priority areas in the European Union. We mapped the capacity and demand of a global (carbon sequestration), a regional (flood regulation), and 3 local ESs (air quality, pollination, and urban leisure). We used Zonation software to identify priority areas for ESs based on 6 tests: with and without accounting for ES demand and 4 tests that accounted for the effect of ES flow zone. There was only 37.1% overlap between the 25% of priority areas that encompassed the most ESs with and without accounting for ES demand. The level of ESs maintained in the priority areas increased from 23.2% to 57.9% after accounting for ES demand, especially for ESs with a small flow zone. Accounting for flow zone had a small effect on the location of priority areas and level of ESs maintained but resulted in fewer flow zones without ES maintained relative to ignoring flow zones. Accounting for demand and flow zones enhanced representation and distribution of ESs with local to regional flow zones without large trade-offs relative to the global ES. We found that ignoring ES demand led to the identification of priority areas in remote regions where benefits from ES capacity to society were small. Incorporating ESs in conservation planning should therefore always account for ES demand to identify an effective priority network for ESs. © 2016 The Authors. Conservation Biology published by Wiley Periodicals, Inc. on behalf of Society for Conservation Biology.

Use of demand for and spatial flow of ecosystem services to identify priority areas

NARCIS (Netherlands)

Verhagen, Willem; Kukkala, Aija S.; Moilanen, Atte; van Teeffelen, Astrid J.A.; Verburg, Peter H.

2017-01-01

Policies and research increasingly focus on the protection of ecosystem services (ESs) through priority-area conservation. Priority areas for ESs should be identified based on ES capacity and ES demand and account for the connections between areas of ES capacity and demand (flow) resulting in areas

spatially identifying vulnerable areas

African Journals Online (AJOL)

The model structure is aimed at understanding the critical vulnerable factors that ... This paper incorporates multiple criteria and rank risk factors. ..... In terms of quantifying vulnerable areas within the country, the analysis is done based on 9 ...

Identifying knickpoints using elevation breaks and offsets in slope-area scaling

Science.gov (United States)

Peifer Bezerra, Daniel; Persano, Cristina

2017-04-01

Steepened longitudinal river profile reaches, usually referred as knickpoints, are geomorphological fingerprints of tectonic, climatic and other perturbations, such as stream capture and sea level changes. Morphologically, knickpoints are distinguished as downstream increases in river gradient and as a break in slope-area scaling; that should theoretically correspond to along-stream variations in incision rate. Hence, the presence of knickpoints is a signature of the transgression of the steady state condition of fluvial systems (or of the spatial uniformity of boundary conditions), being thus the main distinctive feature of transient landscapes. Following a rapid change in relative base level fall rates, the fluvial adjustment occurs through an upstream migration of a knickpoint, taken the detachment-limited condition of the river as given. The knickpoint thus define three distinct reaches: the upstream reach not yet affected by the rejuvenation, the over-steepened reach containing the knickpoint, and the downstream reach that is graded to the new base level. Accordingly, migrating knickpoints have been documented in a myriad of geomorphological contexts such as post-glacial rebound, local earthquake faulting, an increase in fault throw rate and change in sea level. The study of the erosional response in upland landscapes to tectonic, climatic and other perturbations is intrinsically tied to the study of knickpoints. However, the ubiquity of knickpoints in landscape evolution studies is not bound with a precise definition of it, or with a unified methodology for its identification. Hence, we address here the issue of the determination of knickpoints in bedrock rivers using quantitative longitudinal profile analysis. We explored the different methods of identification of knickpoints in the literature, focusing on its definition, calculation, theoretical limitations and interpretation possibilities. Additionally, we applied those methods to a mountainous landward

Identifying Non-Volatile Data Storage Areas: Unique Notebook Identification Information as Digital Evidence

Directory of Open Access Journals (Sweden)

Nikica Budimir

2007-03-01

Full Text Available The research reported in this paper introduces new techniques to aid in the identification of recovered notebook computers so they may be returned to the rightful owner. We identify non-volatile data storage areas as a means of facilitating the safe storing of computer identification information. A forensic proof of concept tool has been designed to test the feasibility of several storage locations identified within this work to hold the data needed to uniquely identify a computer. The tool was used to perform the creation and extraction of created information in order to allow the analysis of the non-volatile storage locations as valid storage areas capable of holding and preserving the data created within them.  While the format of the information used to identify the machine itself is important, this research only discusses the insertion, storage and ability to retain such information.

Identifying Important Atlantic Areas for the conservation of Balearic shearwaters: Spatial overlap with conservation areas

Science.gov (United States)

Pérez-Roda, Amparo; Delord, Karine; Boué, Amélie; Arcos, José Manuel; García, David; Micol, Thierry; Weimerskirch, Henri; Pinaud, David; Louzao, Maite

2017-07-01

Marine protected areas (MPAs) are considered one of the main tools in both fisheries and conservation management to protect threatened species and their habitats around the globe. However, MPAs are underrepresented in marine environments compared to terrestrial environments. Within this context, we studied the Atlantic non-breeding distribution of the southern population of Balearic shearwaters (Puffinus mauretanicus) breeding in Eivissa during the 2011-2012 period based on global location sensing (GLS) devices. Our objectives were (1) to identify overall Important Atlantic Areas (IAAs) from a southern population, (2) to describe spatio-temporal patterns of oceanographic habitat use, and (3) to assess whether existing conservation areas (Natura 2000 sites and marine Important Bird Areas (IBAs)) cover the main IAAs of Balearic shearwaters. Our results highlighted that the Atlantic staging (from June to October in 2011) dynamic of the southern population was driven by individual segregation at both spatial and temporal scales. Individuals ranged in the North-East Atlantic over four main IAAs (Bay of Biscay: BoB, Western Iberian shelf: WIS, Gulf of Cadiz: GoC, West of Morocco: WoM). While most individuals spent more time on the WIS or in the GoC, a small number of birds visited IAAs at the extremes of their Atlantic distribution range (i.e., BoB and WoM). The chronology of the arrivals to the IAAs showed a latitudinal gradient with northern areas reached earlier during the Atlantic staging. The IAAs coincided with the most productive areas (higher chlorophyll a values) in the NE Atlantic between July and October. The spatial overlap between IAAs and conservation areas was higher for Natura 2000 sites than marine IBAs (areas with and without legal protection, respectively). Concerning the use of these areas, a slightly higher proportion of estimated positions fell within marine IBAs compared to designated Natura 2000 sites, with Spanish and Portuguese conservation

77 FR 22663 - Asian Longhorned Beetle; Additions to Quarantined Areas in Massachusetts

Science.gov (United States)

2012-04-17

...-0128] Asian Longhorned Beetle; Additions to Quarantined Areas in Massachusetts AGENCY: Animal and Plant... adopting as a final rule, without change, an interim rule that amended the Asian longhorned beetle (ALB... INFORMATION: Background The Asian longhorned beetle (ALB, Anoplophora glabripennis), an insect native to China...

[Identifying areas of epidemiological stratification in an onchocerciasis focus in Yanomami territory, Roraima, Brazil].

Science.gov (United States)

Coelho, G E; Vieira, J B; Garcia-Zapata, M T; Schuertz, J C

1998-01-01

In this paper, aimed at suitable planning, analysis, and follow-up of treatment, control, and eradication in a human onchocerciasis program, were studied 27 geographic areas and examined 3,974 inhabitants. Four epidemiological areas with different prevalences were identified and stratified.

Isotope techniques to identify recharge areas of springs for rainwater harvesting in the mountainous region of Gaucher area, Chamoli district, Uttarakhand

International Nuclear Information System (INIS)

Shivanna, K.; Tirumalesh, K.; Noble, J.; Joseph, T.B.; Singh, Gursharan; Joshi, A.P.; Khati, V.S.

2008-01-01

Environmental isotope techniques have been employed to identify the recharge areas of springs in India, in order to construct artificial recharge structures for rainwater harvesting and groundwater augmentation for their rejuvenation. A model project was taken up in the mountainous region of Gaucher area, Chamoli District, Uttarakhand for this purpose. The springs in this regions are seasonal and are derived from seepage waters flowing through the shallow weathered and fractured zone. The chemistry of high-altitude springs is similar to that of precipitation, whereas water-rock interactions contributes to increased mineralization in low-altitude springs. The stable isotopic variation in precipitation suggests that the altitude effect for Gaucher area is -0.55% for δ 18 O and -3.8% for δ 2 H per 100 m rise in altitude. Based on local geology, geomorphology, hydrochemistry and isotope information, the possible recharge areas inferred for valleys 1, 2 and 3 are located at altitudes of 1250, 1330 and 1020 m amsl respectively. Water conservation and recharge structures such as subsurface dykes, check bunds and contour trenches were constructed at the identified recharge areas in the respective valleys for controlling the subsurface flow, rainwater harvesting and groundwater augmentation respectively. As a result, during and after the following monsoon, the discharge rates of the springs not only increased significantly, but also did not dry up even during the dry period. The study shows that the isotope techniques can be effectively used in identifying recharge areas of springs in the Himalayan region. It also demonstrates the advantage of isotope techniques over conventional methods. (author)

Autofluorescence Lifetimes in Patients With Choroideremia Identify Photoreceptors in Areas With Retinal Pigment Epithelium Atrophy.

Science.gov (United States)

Dysli, Chantal; Wolf, Sebastian; Tran, Hoai Viet; Zinkernagel, Martin S

2016-12-01

The purpose of this study was to investigate fundus autofluorescence lifetimes in patients with choroideremia and to identify tissue-specific lifetime characteristics and potential prognostic markers. Autofluorescence lifetimes of the retina were measured in two spectral channels (498-560 nm and 560-720 nm) in patients with choroideremia and age-matched healthy controls. Furthermore, autofluorescence intensities and spectral-domain optical coherence tomography (OCT) data were acquired and compared to fundus autofluorescence lifetime data. Sixteen eyes from 8 patients with advanced choroideremia (mean ± SD age, 55 ± 13 years) were included in this study and compared with 10 age-matched healthy participants. Whereas fundus autofluorescence intensity measurement identified areas of remaining retinal pigment epithelium (RPE), autofluorescence lifetime maps identified areas with remaining photoreceptor layers in OCT but RPE atrophy. In these areas, mean (±SEM) lifetimes were 567 ± 59 ps in the short and 603 ± 49 ps in the long spectral channels (+98% and +88% compared to controls). In areas of combined RPE atrophy and loss of photoreceptors, autofluorescence lifetimes were significantly prolonged by 1116 ± 63 ps (+364%) in the short and by 915 ± 52 ps (+270%) in the long spectral channels compared with controls. Because autofluorescence lifetimes identify areas of remaining photoreceptors in the absence of RPE, this imaging modality may be useful to monitor disease progression in the natural course of disease and in context of potential future therapeutic interventions.

Identifying the Risk Areas and Urban Growth by ArcGIS-Tools

Directory of Open Access Journals (Sweden)

Omar Hamdy

2016-10-01

Full Text Available Abouelreesh is one of the most at risk areas in Aswan, Egypt, which suffers from storms, poor drainage, and flash flooding. These phenomena affect the urban areas and cause a lot of damage to buildings and infrastructure. Moreover, the potential for the further realization of dangerous situations increased when the urban areas of Abouelreesh extended towards the risk areas. In an effort to ameliorate the danger, two key issues for urban growth management were studied, namely: (i estimations regarding the pace of urban sprawl, and (ii the identification of urban areas located in regions that would be affected by flash floods. Analyzing these phenomena require a lot of data in order to obtain good results, but in our case, the official data or field data was limited so we tried to obtain it by accessing two kinds of free sources of satellite data. First, we used Arc GIS tools to analyze (digital elevation model (DEM files in order to study the watershed and better identify the risk area. Second, we studied historical imagery in Google Earth to determine the age of each urban block. The urban growth rate in the risk areas had risen to 63.31% in 2001. Urban growth in the case study area had been influenced by house sizes, because most people were looking to live in bigger houses. The aforementioned problem can be observed by considering the increasing average house sizes from 2001 until 2013, where, especially in risky areas, the average of house sizes had grown from 223 m2 in 2001 to 318 m2 in 2013. The findings from this study would be useful to urban planners and government officials in helping them to make informed decisions on urban development to benefit the community, especially those living in areas at risk from flash flooding from heavy rain events.

Influence of small amounts of additives on gas hold-up, bubble size, and interfacial area

NARCIS (Netherlands)

Cents, A. H. G.; Jansen, D. J. W.; Brilman, D. W. F.; Versteeg, G. F.

2005-01-01

The gas-liquid interfacial area, which is determined by the gas hold-up and the Sauter mean bubble diameter, determines the production rate in many industrial processes. The effect of additives on this interfacial area is, especially in multiphase systems (gas-liquid-solid, gas-liquid-liquid), often

Identifying settlements on the SIR-B images of Rimbobujang and the surrounding areas, Sumatra, Indonesia

Directory of Open Access Journals (Sweden)

Sutanto .

2013-07-01

SIR-B image proves to be a reasonably good tool to identify rural settlement in an open area, especially for that with high density of houses. Its use to identify towns and cities is more recommended.

Workshop Report on Additive Manufacturing for Large-Scale Metal Components - Development and Deployment of Metal Big-Area-Additive-Manufacturing (Large-Scale Metals AM) System

Energy Technology Data Exchange (ETDEWEB)

Babu, Sudarsanam Suresh [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility; Love, Lonnie J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility; Peter, William H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility; Dehoff, Ryan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility

2016-05-01

Additive manufacturing (AM) is considered an emerging technology that is expected to transform the way industry can make low-volume, high value complex structures. This disruptive technology promises to replace legacy manufacturing methods for the fabrication of existing components in addition to bringing new innovation for new components with increased functional and mechanical properties. This report outlines the outcome of a workshop on large-scale metal additive manufacturing held at Oak Ridge National Laboratory (ORNL) on March 11, 2016. The charter for the workshop was outlined by the Department of Energy (DOE) Advanced Manufacturing Office program manager. The status and impact of the Big Area Additive Manufacturing (BAAM) for polymer matrix composites was presented as the background motivation for the workshop. Following, the extension of underlying technology to low-cost metals was proposed with the following goals: (i) High deposition rates (approaching 100 lbs/h); (ii) Low cost (<$10/lbs) for steel, iron, aluminum, nickel, as well as, higher cost titanium, (iii) large components (major axis greater than 6 ft) and (iv) compliance of property requirements. The above concept was discussed in depth by representatives from different industrial sectors including welding, metal fabrication machinery, energy, construction, aerospace and heavy manufacturing. In addition, DOE’s newly launched High Performance Computing for Manufacturing (HPC4MFG) program was reviewed. This program will apply thermo-mechanical models to elucidate deeper understanding of the interactions between design, process, and materials during additive manufacturing. Following these presentations, all the attendees took part in a brainstorming session where everyone identified the top 10 challenges in large-scale metal AM from their own perspective. The feedback was analyzed and grouped in different categories including, (i) CAD to PART software, (ii) selection of energy source, (iii

Utility of Big Area Additive Manufacturing (BAAM) For The Rapid Manufacture of Customized Electric Vehicles

Energy Technology Data Exchange (ETDEWEB)

Love, Lonnie J [ORNL

2015-08-01

This Oak Ridge National Laboratory (ORNL) Manufacturing Development Facility (MDF) technical collaboration project was conducted in two phases as a CRADA with Local Motors Inc. Phase 1 was previously reported as Advanced Manufacturing of Complex Cyber Mechanical Devices through Community Engagement and Micro-manufacturing and demonstrated the integration of components onto a prototype body part for a vehicle. Phase 2 was reported as Utility of Big Area Additive Manufacturing (BAAM) for the Rapid Manufacture of Customized Electric Vehicles and demonstrated the high profile live printing of an all-electric vehicle using ONRL s Big Area Additive Manufacturing (BAAM) technology. This demonstration generated considerable national attention and successfully demonstrated the capabilities of the BAAM system as developed by ORNL and Cincinnati, Inc. and the feasibility of additive manufacturing of a full scale electric vehicle as envisioned by the CRADA partner Local Motors, Inc.

Combining endangered plants and animals as surrogates to identify priority conservation areas in Yunnan, China

Science.gov (United States)

Yang, Feiling; Hu, Jinming; Wu, Ruidong

2016-08-01

Suitable surrogates are critical for identifying optimal priority conservation areas (PCAs) to protect regional biodiversity. This study explored the efficiency of using endangered plants and animals as surrogates for identifying PCAs at the county level in Yunnan, southwest China. We ran the Dobson algorithm under three surrogate scenarios at 75% and 100% conservation levels and identified four types of PCAs. Assessment of the protection efficiencies of the four types of PCAs showed that endangered plants had higher surrogacy values than endangered animals but that the two were not substitutable; coupled endangered plants and animals as surrogates yielded a higher surrogacy value than endangered plants or animals as surrogates; the plant-animal priority areas (PAPAs) was the optimal among the four types of PCAs for conserving both endangered plants and animals in Yunnan. PAPAs could well represent overall species diversity distribution patterns and overlap with critical biogeographical regions in Yunnan. Fourteen priority units in PAPAs should be urgently considered as optimizing Yunnan’s protected area system. The spatial pattern of PAPAs at the 100% conservation level could be conceptualized into three connected conservation belts, providing a valuable reference for optimizing the layout of the in situ protected area system in Yunnan.

Using Hospitalization and Mortality Data to Identify Areas at Risk for Adolescent Suicide.

Science.gov (United States)

Chen, Kun; Aseltine, Robert H

2017-08-01

The purpose of this study is to use statewide data on inpatient hospitalizations for suicide attempts and suicide mortality to identify communities and school districts at risk for adolescent suicide. Five years of data (2010-2014) from the Office of the Connecticut Medical Examiner and the Connecticut Hospital Inpatient Discharge Database were analyzed. A mixed-effects Poisson regression model was used to assess whether suicide attempt/mortality rates in the state's 119 school districts were significantly better or worse than expected after adjusting for 10 community-level characteristics. Ten districts were at significantly higher risk for suicidal behavior, with suicide mortality/hospitalization rates ranging from 154% to 241% of their expected rates, after accounting for their community characteristics. Four districts were identified as having significantly lower risk for suicide attempts than expected after accounting for community-level advantages and disadvantages. Data capturing hospitalization for suicide attempts and suicide deaths can inform prevention activities by identifying high-risk areas to which resources should be allocated, as well as low-risk areas that may provide insight into the best practices in suicide prevention. Copyright © 2017 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

49 CFR 192.905 - How does an operator identify a high consequence area?

Science.gov (United States)

2010-10-01

...) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Gas Transmission Pipeline Integrity Management § 192.905 How does an operator identify a high consequence area? (a...

Classifying neighbourhoods by level of access to stores selling fresh fruit and vegetables and groceries: identifying problematic areas in the city of Gatineau, Quebec.

Science.gov (United States)

Gould, Adrian C; Apparicio, Philippe; Cloutier, Marie-Soleil

2012-11-06

Physical access to stores selling groceries, fresh fruit and vegetables (FV) is essential for urban dwellers. In Canadian cities where low-density development practices are common, social and material deprivation may be compounded by poor geographic access to healthy food. This case study examines access to food stores selling fresh FV in Gatineau, Quebec, to identify areas where poor access is coincident with high deprivation. Food retailers were identified using two secondary sources and each store was visited to establish the total surface area devoted to the sale of fresh FV. Four population-weighted accessibility measures were then calculated for each dissemination area (DA) using road network distances. A deprivation index was created using variables from the 2006 Statistics Canada census, also at the scale of the DA. Finally, six classes of accessibility to a healthy diet were constructed using a k-means classification procedure. These were mapped and superimposed over high deprivation areas. Overall, deprivation is positively correlated with better accessibility. However, more than 18,000 residents (7.5% of the population) live in high deprivation areas characterized by large distances to the nearest retail food store (means of 1.4 km or greater) and virtually no access to fresh FV within walking distance (radius of 1 km). In this research, we identified areas where poor geographic access may introduce an additional constraint for residents already dealing with the challenges of limited financial and social resources. Our results may help guide local food security policies and initiatives.

Changing Climate, Challenging Choices: Identifying and Evaluating Climate Change Adaptation Options for Protected Areas Management in Ontario, Canada

Science.gov (United States)

Lemieux, Christopher J.; Scott, Daniel J.

2011-10-01

Climate change will pose increasingly significant challenges to managers of parks and other forms of protected areas around the world. Over the past two decades, numerous scientific publications have identified potential adaptations, but their suitability from legal, policy, financial, internal capacity, and other management perspectives has not been evaluated for any protected area agency or organization. In this study, a panel of protected area experts applied a Policy Delphi methodology to identify and evaluate climate change adaptation options across the primary management areas of a protected area agency in Canada. The panel identified and evaluated one hundred and sixty five (165) adaptation options for their perceived desirability and feasibility. While the results revealed a high level of agreement with respect to the desirability of adaptation options and a moderate level of capacity pertaining to policy formulation and management direction, a perception of low capacity for implementation in most other program areas was identified. A separate panel of senior park agency decision-makers used a multiple criterion decision-facilitation matrix to further evaluate the institutional feasibility of the 56 most desirable adaptation options identified by the initial expert panel and to prioritize them for consideration in a climate change action plan. Critically, only two of the 56 adaptation options evaluated by senior decision-makers were deemed definitely implementable, due largely to fiscal and internal capacity limitations. These challenges are common to protected area agencies in developed countries and pervade those in developing countries, revealing that limited adaptive capacity represents a substantive barrier to biodiversity conservation and other protected area management objectives in an era of rapid climate change.

Process Modeling and Validation for Metal Big Area Additive Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Simunovic, Srdjan [ORNL; Nycz, Andrzej [ORNL; Noakes, Mark W. [ORNL; Chin, Charlie [Dassault Systemes; Oancea, Victor [Dassault Systemes

2017-05-01

Metal Big Area Additive Manufacturing (mBAAM) is a new additive manufacturing (AM) technology based on the metal arc welding. A continuously fed metal wire is melted by an electric arc that forms between the wire and the substrate, and deposited in the form of a bead of molten metal along the predetermined path. Objects are manufactured one layer at a time starting from the base plate. The final properties of the manufactured object are dependent on its geometry and the metal deposition path, in addition to depending on the basic welding process parameters. Computational modeling can be used to accelerate the development of the mBAAM technology as well as a design and optimization tool for the actual manufacturing process. We have developed a finite element method simulation framework for mBAAM using the new features of software ABAQUS. The computational simulation of material deposition with heat transfer is performed first, followed by the structural analysis based on the temperature history for predicting the final deformation and stress state. In this formulation, we assume that two physics phenomena are coupled in only one direction, i.e. the temperatures are driving the deformation and internal stresses, but their feedback on the temperatures is negligible. The experiment instrumentation (measurement types, sensor types, sensor locations, sensor placements, measurement intervals) and the measurements are presented. The temperatures and distortions from the simulations show good correlation with experimental measurements. Ongoing modeling work is also briefly discussed.

Space-Time Analysis to Identify Areas at Risk of Mortality from Cardiovascular Disease

Directory of Open Access Journals (Sweden)

Poliany C. O. Rodrigues

2015-01-01

Full Text Available This study aimed at identifying areas that were at risk of mortality due to cardiovascular disease in residents aged 45 years or older of the cities of Cuiabá and Várzea Grande between 2009 and 2011. We conducted an ecological study of mortality rates related to cardiovascular disease. Mortality rates were calculated for each census tract by the Local Empirical Bayes estimator. High- and low-risk clusters were identified by retrospective space-time scans for each year using the Poisson probability model. We defined the year and month as the temporal analysis unit and the census tracts as the spatial analysis units adjusted by age and sex. The Mann-Whitney U test was used to compare the socioeconomic and environmental variables by risk classification. High-risk clusters showed higher income ratios than low-risk clusters, as did temperature range and atmospheric particulate matter. Low-risk clusters showed higher humidity than high-risk clusters. The Eastern region of Várzea Grande and the central region of Cuiabá were identified as areas at risk of mortality due to cardiovascular disease in individuals aged 45 years or older. High mortality risk was associated with socioeconomic and environmental factors. More high-risk clusters were observed at the end of the dry season.

Identifying the Areas Benefitting from the Prevention of Wind Erosion by the Key Ecological Function Area for the Protection of Desertification in Hunshandake, China

Directory of Open Access Journals (Sweden)

Yu Xiao

2017-10-01

Full Text Available Research on the spatial flow of ecosystem services can help to identify the spatial relationships between service-providing areas (SPAs and service-benefitting areas (SBAs. In this study, we used the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT model to stimulate the flow paths of the wind erosion prevented by ecosystems in Hunshandake, China. By interpolating these paths, the SBAs were identified, and their benefits in terms of land cover, population, and Gross Domestic Product (GDP were determined. The results indicated that the flow paths mostly extended to the eastern part of the study area, and the estimated cover of the SBAs was 39.21% of the total area of China. The grid cells through which many (≥10% of the trajectories passed were mainly located in the western part of north-eastern China and the eastern part of northern China. The benefitting population accounted for 74.51% of the total population of China, and the GDP was 67.11% of the total in 2010. Based on this research, we described a quantitative relationship between the SPAs and the SBAs and identified the actual beneficiaries. This work may provide scientific knowledge that can be used by decision makers to develop management strategies, such as ecological compensation to mitigate damage from sandstorms in the study area.

Performance of the lot quality assurance sampling method compared to surveillance for identifying inadequately-performing areas in Matlab, Bangladesh.

Science.gov (United States)

Bhuiya, Abbas; Hanifi, S M A; Roy, Nikhil; Streatfield, P Kim

2007-03-01

This paper compared the performance of the lot quality assurance sampling (LQAS) method in identifying inadequately-performing health work-areas with that of using health and demographic surveillance system (HDSS) data and examined the feasibility of applying the method by field-level programme supervisors. The study was carried out in Matlab, the field site of ICDDR,B, where a HDSS has been in place for over 30 years. The LQAS method was applied in 57 work-areas of community health workers in ICDDR,B-served areas in Matlab during July-September 2002. The performance of the LQAS method in identifying work-areas with adequate and inadequate coverage of various health services was compared with those of the HDSS. The health service-coverage indicators included coverage of DPT, measles, BCG vaccination, and contraceptive use. It was observed that the difference in the proportion of work-areas identified to be inadequately performing using the LQAS method with less than 30 respondents, and the HDSS was not statistically significant. The consistency between the LQAS method and the HDSS in identifying work-areas was greater for adequately-performing areas than inadequately-performing areas. It was also observed that the field managers could be trained to apply the LQAS method in monitoring their performance in reaching the target population.

V-shaped resonators for addition of broad-area laser diode arrays

Science.gov (United States)

Liu, Bo; Liu, Yun; Braiman, Yehuda Y.

2012-12-25

A system and method for addition of broad-area semiconductor laser diode arrays are described. The system can include an array of laser diodes, a V-shaped external cavity, and grating systems to provide feedback for phase-locking of the laser diode array. A V-shaped mirror used to couple the laser diode emissions along two optical paths can be a V-shaped prism mirror, a V-shaped stepped mirror or include multiple V-shaped micro-mirrors. The V-shaped external cavity can be a ring cavity. The system can include an external injection laser to further improve coherence and phase-locking.

Comparing spatially explicit ecological and social values for natural areas to identify effective conservation strategies.

Science.gov (United States)

Bryan, Brett Anthony; Raymond, Christopher Mark; Crossman, Neville David; King, Darran

2011-02-01

Consideration of the social values people assign to relatively undisturbed native ecosystems is critical for the success of science-based conservation plans. We used an interview process to identify and map social values assigned to 31 ecosystem services provided by natural areas in an agricultural landscape in southern Australia. We then modeled the spatial distribution of 12 components of ecological value commonly used in setting spatial conservation priorities. We used the analytical hierarchy process to weight these components and used multiattribute utility theory to combine them into a single spatial layer of ecological value. Social values assigned to natural areas were negatively correlated with ecological values overall, but were positively correlated with some components of ecological value. In terms of the spatial distribution of values, people valued protected areas, whereas those natural areas underrepresented in the reserve system were of higher ecological value. The habitats of threatened animal species were assigned both high ecological value and high social value. Only small areas were assigned both high ecological value and high social value in the study area, whereas large areas of high ecological value were of low social value, and vice versa. We used the assigned ecological and social values to identify different conservation strategies (e.g., information sharing, community engagement, incentive payments) that may be effective for specific areas. We suggest that consideration of both ecological and social values in selection of conservation strategies can enhance the success of science-based conservation planning. ©2010 Society for Conservation Biology.

Identifying Potential Area and Financial Prospects of Rooftop Solar Photovoltaics (PV

Directory of Open Access Journals (Sweden)

Sarawut Ninsawat

2016-10-01

Full Text Available In an urban area, the roof is the only available surface that can be utilized for installing solar photovoltaics (PV, and the active surface area depends on the type of roof. Shadows on a solar panel can be caused by nearby tall buildings, construction materials such as water tanks, or the roof configuration itself. The azimuth angle of the sun varies, based on the season and the time of day. Therefore, the simulation of shadow for one or two days or using the rule of thumb may not be sufficient to evaluate shadow effects on solar panels throughout the year. In this paper, a methodology for estimating the solar potential of solar PV on rooftops is presented, which is particularly applicable to urban areas. The objective of this method is to assess how roof type and shadow play a role in potentiality and financial benefit. The method starts with roof type extraction from high-resolution satellite imagery, using Object Base Image Analysis (OBIA, the generation of a 3D structure from height data and roof type, the simulation of shadow throughout the year, and the identification of potential and financial prospects. Based on the results obtained, the system seems to be adequate for calculating the financial benefits of solar PV to a very fine scale. The payback period varied from 7–13 years depending on the roof type, direction, and shadow impact. Based on the potentiality, a homeowner can make a profit of up to 200%. This method could help homeowners to identify potential roof area and economic interest.

Wastewater Reuse: An Economic Perspective to Identify Suitable Areas for Poplar Vegetation Filter Systems for Energy Production

Directory of Open Access Journals (Sweden)

Mauro Viccaro

2017-11-01

Full Text Available The increasing interest towards climate change, water and energy saving, and soil protection has led the research community to consider non-conventional water as a sustainable source for irrigation of energy crops. Vegetation filter systems are considered a reliable technique for sustainable biomass cultivation, enabling the use of reclaimed wastewater as water and nutrients sources during irrigation periods. In this study, a geographic information system (GIS-based spatial model was developed to identify areas potentially suitable for creating vegetation filter systems with poplars to size the plants of energy production. An economic assessment allowed us to identify the cost-effectiveness areas for biomass production that can be fertigated by reclaimed wastewater. Considering the Basilicata region as the test region, a surface area of 258,512 ha was investigated, identifying 73,331 ha of SRF soils sited downstream of 45 wastewater treatment plants (WWTPs. However, considering only areas that have positive net present value and are economically attractive, results indicate 1606 ha of SRF falling within the areas of influence of 39 WWTPs. The results show that the sector of dedicated crops, adjacent and linked with WWTPs, expresses a total capacity of 50.56 MW for thermal, 8.25 MW for electricity, and 31 MW for cogeneration (25.07 MWt and 5.94 MWe plants.

Assigning dates and identifying areas affected by fires in Portugal based on MODIS data

Directory of Open Access Journals (Sweden)

JESSICA PANISSET

Full Text Available ABSTRACT An automated procedure is here presented that allows identifying and dating burned areas in Portugal using values of daily reflectance from near-infrared and middle-infrared bands, as obtained from the MODIS instrument. The algorithm detects persistent changes in monthly composites of the so-called (V,W Burn-Sensitive Index and the day of maximum change in daily time series of W is in turn identified as the day of the burning event. The procedure is tested for 2005, the second worst fire season ever recorded in Portugal. Comparison between the obtained burned area map and the reference derived from Landsat imagery resulted in a Proportion Correct of 95.6%. Despite being applied only to the months of August and September, the algorithm is able to identify almost two-thirds of all scars that have occurred during the entire year of 2005. An assessment of the temporal accuracy of the dating procedure was also conducted, showing that 75% of estimated dates presented deviations between -5 and 5 days from dates of hotspots derived from the MODIS instrument. Information about location and date of burning events as provided by the proposed procedure may be viewed as complementary to the currently available official maps based on end-of-season Landsat imagery.

76 FR 1337 - Asian Longhorned Beetle; Additions to Quarantined Areas in Massachusetts and New York

Science.gov (United States)

2011-01-10

.... APHIS-2009-0014] Asian Longhorned Beetle; Additions to Quarantined Areas in Massachusetts and New York... rule. SUMMARY: We are adopting as a final rule, without change, an interim rule that amended the Asian..., MD 20737-1231; (301) 734-5705. SUPPLEMENTARY INFORMATION: Background The Asian longhorned beetle (ALB...

Identifiability of Additive Actuator and Sensor Faults by State Augmentation

Science.gov (United States)

Joshi, Suresh; Gonzalez, Oscar R.; Upchurch, Jason M.

2014-01-01

A class of fault detection and identification (FDI) methods for bias-type actuator and sensor faults is explored in detail from the point of view of fault identifiability. The methods use state augmentation along with banks of Kalman-Bucy filters for fault detection, fault pattern determination, and fault value estimation. A complete characterization of conditions for identifiability of bias-type actuator faults, sensor faults, and simultaneous actuator and sensor faults is presented. It is shown that FDI of simultaneous actuator and sensor faults is not possible using these methods when all sensors have unknown biases. The fault identifiability conditions are demonstrated via numerical examples. The analytical and numerical results indicate that caution must be exercised to ensure fault identifiability for different fault patterns when using such methods.

Differentiation of specific ripple patterns helps to identify epileptogenic areas for surgical procedures.

Science.gov (United States)

Kerber, Karolin; Dümpelmann, Matthias; Schelter, Björn; Le Van, Pierre; Korinthenberg, Rudolf; Schulze-Bonhage, Andreas; Jacobs, Julia

2014-07-01

High frequency oscillations (HFOs) at 80-500 Hz are promising markers of epileptic areas. Several retrospective studies reported that surgical removal of areas generating HFOs was associated with a good seizure outcome. Recent reports suggested that ripple (80-200 Hz) HFO patterns co-existed with different background EEG activities. We hypothesized that the coexisting background EEG pattern may distinguish physiological from epileptic ripples. Rates of HFOs were analyzed in intracranial EEG recordings of 22 patients. Additionally, ripple patterns were classified for each channel depending either as coexisting with a flat or oscillatory background activity. A multi-variate analysis was performed to determine whether removal of areas showing the above EEG markers correlated with seizure outcome. Removal of areas generating high rates of 'fast ripples (>200 Hz)' and 'ripples on a flat background activity' showed a significant correlation with a seizure-free outcome. In contrast, removal of high rates of 'ripples' or 'ripple patterns in a continuously oscillating background' was not significantly associated with seizure outcome. Ripples occurring in an oscillatory background activity may be suggestive of physiological activity, while those on a flat background reflect epileptic activity. Consideration of coexisting background patterns may improve the delineation of the epileptogenic areas using ripple oscillations. Copyright © 2013 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.

LITTER PRODUCTION AND NUTRIENT ADDITION IN ATLANTIC FOREST AREAS IN SANTA MARIA DE JETIBÁ, ES

Directory of Open Access Journals (Sweden)

Geângelo Petene Calvi

2009-09-01

Full Text Available This study was accomplished on Espíndula Farm, Santa Maria de Jetibá (ES, with the objective of evaluating the litter and nutrients deposition in areas with different succession stadiums. Two areas were selected with different vegetable coverings, defined as: (SF Secondary Forest, with about 25 ha of area, corresponding to an old area of cassava cultivation with about 50 years in process of ecological succession and where today there is a secondary forest and an Old Secondary Forest (OSF corresponding to a forest area that has just been submitted to a selective wood extraction for use of the farm itself. In each one of vegetal areas, approximately 0.1 ha was delimited and in these ten conical collectors were randomized distributed. The litter collections were accomplished monthly from November 2003 to October 2005. After drying, the material was stratified and the total contributed and the contribution of the different fractions, and the nutritious addition were evaluated. It was not verified significant differences among the total of litter deposited among the areas, being the highest production values observed in the summer, 5.70 Mg ha-1 (SF and 5.73 Mg ha-1(OSF, possibly due to the winds and rain mechanical action. The fraction of higher contribution was the foliar, corresponding to 74.62% for the SF area and 69.46% for the OSF area

Using EVT for Geological Anomaly Design and Its Application in Identifying Anomalies in Mining Areas

Directory of Open Access Journals (Sweden)

Feilong Qin

2016-01-01

Full Text Available A geological anomaly is the basis of mineral deposit prediction. Through the study of the knowledge and characteristics of geological anomalies, the category of extreme value theory (EVT to which a geological anomaly belongs can be determined. Associating the principle of the EVT and ensuring the methods of the shape parameter and scale parameter for the generalized Pareto distribution (GPD, the methods to select the threshold of the GPD can be studied. This paper designs a new algorithm called the EVT model of geological anomaly. These study data on Cu and Au originate from 26 exploration lines of the Jiguanzui Cu-Au mining area in Hubei, China. The proposed EVT model of the geological anomaly is applied to identify anomalies in the Jiguanzui Cu-Au mining area. The results show that the model can effectively identify the geological anomaly region of Cu and Au. The anomaly region of Cu and Au is consistent with the range of ore bodies of actual engineering exploration. Therefore, the EVT model of the geological anomaly can effectively identify anomalies, and it has a high indicating function with respect to ore prospecting.

Failure mode effects and criticality analysis: innovative risk assessment to identify critical areas for improvement in emergency department sepsis resuscitation.

Science.gov (United States)

Powell, Emilie S; O'Connor, Lanty M; Nannicelli, Anna P; Barker, Lisa T; Khare, Rahul K; Seivert, Nicholas P; Holl, Jane L; Vozenilek, John A

2014-06-01

Sepsis is an increasing problem in the practice of emergency medicine as the prevalence is increasing and optimal care to reduce mortality requires significant resources and time. Evidence-based septic shock resuscitation strategies exist, and rely on appropriate recognition and diagnosis, but variation in adherence to the recommendations and therefore outcomes remains. Our objective was to perform a multi-institutional prospective risk-assessment, using failure mode effects and criticality analysis (FMECA), to identify high-risk failures in ED sepsis resuscitation. We conducted a FMECA, which prospectively identifies critical areas for improvement in systems and processes of care, across three diverse hospitals. A multidisciplinary group of participants described the process of emergency department (ED) sepsis resuscitation to then create a comprehensive map and table listing all process steps and identified process failures. High-risk failures in sepsis resuscitation from each of the institutions were compiled to identify common high-risk failures. Common high-risk failures included limited availability of equipment to place the central venous catheter and conduct invasive monitoring, and cognitive overload leading to errors in decision-making. Additionally, we identified great variability in care processes across institutions. Several common high-risk failures in sepsis care exist: a disparity in resources available across hospitals, a lack of adherence to the invasive components of care, and cognitive barriers that affect expert clinicians' decision-making capabilities. Future work may concentrate on dissemination of non-invasive alternatives and overcoming cognitive barriers in diagnosis and knowledge translation.

The perceptions of teachers and principals toward providing additional compensation to teachers in high-need subject areas

Science.gov (United States)

Longing, Jeffrey Lucian

The purpose of this study was to determine possible differences in the perceptions of teachers teaching in high-need areas (i.e., math, science, special education, etc.) and teachers not teaching in high-need areas, (i.e., business education, physical education, etc.) as defined by the states of Arkansas and Louisiana, regarding higher compensation for high-need teachers. In addition, possible perception differences among principals and teachers were determined. The independent variables consisted of gender, position held, years of certified experience, and certification areas. The dependent variable was the perceptions of the participants on providing higher compensation for high-need teachers in order to attract and retain them. The data for all variables were collected using the Teacher Compensation Survey. The sample for this study was limited to teachers, grades 9 through 12, and principals of public high schools in south Arkansas and north Louisiana. Forty-four school districts in south Arkansas (Arkansas Department of Education, 2008a) and north Louisiana (Louisiana Department of Education, 2008a) met the criteria for this study. Twenty-two superintendents gave permission for their districts to participate in the research. A sample of 849 teachers and 38 principals were identified in these districts. Surveys were returned from 350 teachers, creating a 41% response rate. When the 31 principals that returned surveys were added to the total population, the response rate increased to 43% with 381 of the 887 surveyed responding. However, 42 of the teachers and two of the principals skipped some of the questions on the survey and were not included in the study. The researcher used a One-Way ANOVA and independent t-tests to determine the presence of statistical differences at the .05 level. The data showed that most math and science teachers agreed that high-need teachers should be compensated at a higher rate than teachers not teaching in high-need areas. The data

Big Area Additive Manufacturing of High Performance Bonded NdFeB Magnets

Science.gov (United States)

Li, Ling; Tirado, Angelica; Nlebedim, I. C.; Rios, Orlando; Post, Brian; Kunc, Vlastimil; Lowden, R. R.; Lara-Curzio, Edgar; Fredette, Robert; Ormerod, John; Lograsso, Thomas A.; Paranthaman, M. Parans

2016-10-01

Additive manufacturing allows for the production of complex parts with minimum material waste, offering an effective technique for fabricating permanent magnets which frequently involve critical rare earth elements. In this report, we demonstrate a novel method - Big Area Additive Manufacturing (BAAM) - to fabricate isotropic near-net-shape NdFeB bonded magnets with magnetic and mechanical properties comparable or better than those of traditional injection molded magnets. The starting polymer magnet composite pellets consist of 65 vol% isotropic NdFeB powder and 35 vol% polyamide (Nylon-12). The density of the final BAAM magnet product reached 4.8 g/cm3, and the room temperature magnetic properties are: intrinsic coercivity Hci = 688.4 kA/m, remanence Br = 0.51 T, and energy product (BH)max = 43.49 kJ/m3 (5.47 MGOe). In addition, tensile tests performed on four dog-bone shaped specimens yielded an average ultimate tensile strength of 6.60 MPa and an average failure strain of 4.18%. Scanning electron microscopy images of the fracture surfaces indicate that the failure is primarily related to the debonding of the magnetic particles from the polymer binder. The present method significantly simplifies manufacturing of near-net-shape bonded magnets, enables efficient use of rare earth elements thus contributing towards enriching the supply of critical materials.

Using Landsat 5 TM Data to Identify and Map Areas of Mangrove in Tulum, Quintana Roo, Mexico

Science.gov (United States)

Meachum, Samuel Standish

Mangroves are recognized worldwide as a major ecosystem that provides significant ecosystem services. They are threatened due to rising pressures from human overpopulation and economic development. The Caribbean Coast of Mexico's Yucatan Peninsula contains mangrove habitat that have been negatively impacted by the development of the region's tourist industry. However, little research has been done to map and quantify the extent of mangrove in the region. This study used remote sensing techniques to identify mangrove in the Municipality of Tulum located in Quintana Roo, and to produce an accurate vector based thematic map that inventories these areas. Anatomical differences were analyzed and related to high-resolution field spectral data for each mangrove species. A vector map of mangrove habitat, including areas of inland mangrove, was produced with an overall accuracy of 88%. The 19,262 ha. of mangrove identified by this study represents a 140% increase in area over previous studies.

Creating Protected Areas on Public Lands: Is There Room for Additional Conservation?

Directory of Open Access Journals (Sweden)

Rodrigo A Arriagada

Full Text Available Most evaluations of the effectiveness of PAs have relied on indirect estimates based on comparisons between protected and unprotected areas. Such methods can be biased when protection is not randomly assigned. We add to the growing literature on the impact of PAs by answering the following research questions: What is the impact of Chilean PAs on deforestation which occurred between 1986 and 2011? How do estimates of the impact of PAs vary when using only public land as control units? We show that the characteristics of the areas in which protected and unprotected lands are located differ significantly. To satisfactorily estimate the effects of PAs, we use matching methods to define adequate control groups, but not as in previous research. We construct control groups using separately non-protected private areas and non-protected public lands. We find that PAs avoid deforestation when using unprotected private lands as valid controls, however results show no impact when the control group is based only on unprotected public land. Different land management regimes, and higher levels of enforcement inside public lands may reduce the opportunity to add additional conservation benefits when the national systems for PAs are based on the protection of previously unprotected public lands. Given that not all PAs are established to avoid deforestation, results also admit the potential for future studies to include other outcomes including forest degradation (not just deforestation, biodiversity, wildlife, primary forests (not forests in general, among others.

Creating Protected Areas on Public Lands: Is There Room for Additional Conservation?

Science.gov (United States)

Arriagada, Rodrigo A; Echeverria, Cristian M; Moya, Danisa E

2016-01-01

Most evaluations of the effectiveness of PAs have relied on indirect estimates based on comparisons between protected and unprotected areas. Such methods can be biased when protection is not randomly assigned. We add to the growing literature on the impact of PAs by answering the following research questions: What is the impact of Chilean PAs on deforestation which occurred between 1986 and 2011? How do estimates of the impact of PAs vary when using only public land as control units? We show that the characteristics of the areas in which protected and unprotected lands are located differ significantly. To satisfactorily estimate the effects of PAs, we use matching methods to define adequate control groups, but not as in previous research. We construct control groups using separately non-protected private areas and non-protected public lands. We find that PAs avoid deforestation when using unprotected private lands as valid controls, however results show no impact when the control group is based only on unprotected public land. Different land management regimes, and higher levels of enforcement inside public lands may reduce the opportunity to add additional conservation benefits when the national systems for PAs are based on the protection of previously unprotected public lands. Given that not all PAs are established to avoid deforestation, results also admit the potential for future studies to include other outcomes including forest degradation (not just deforestation), biodiversity, wildlife, primary forests (not forests in general), among others.

Meta-analysis identifies 29 additional ulcerative colitis risk loci, increasing the number of confirmed associations to 47

DEFF Research Database (Denmark)

Anderson, Carl A; Boucher, Gabrielle; Lees, Charlie W

2011-01-01

Genome-wide association studies and candidate gene studies in ulcerative colitis have identified 18 susceptibility loci. We conducted a meta-analysis of six ulcerative colitis genome-wide association study datasets, comprising 6,687 cases and 19,718 controls, and followed up the top association...... signals in 9,628 cases and 12,917 controls. We identified 29 additional risk loci (P associated loci to 47. After annotating associated regions using GRAIL, expression quantitative trait loci data and correlations with non-synonymous SNPs, we...... identified many candidate genes that provide potentially important insights into disease pathogenesis, including IL1R2, IL8RA-IL8RB, IL7R, IL12B, DAP, PRDM1, JAK2, IRF5, GNA12 and LSP1. The total number of confirmed inflammatory bowel disease risk loci is now 99, including a minimum of 28 shared association...

Calculation of climate factors as an additional criteria to determine agriculturally less favoured areas

Directory of Open Access Journals (Sweden)

Tjaša POGAČAR

2016-04-01

Full Text Available Climate factors that are proposed to determine agriculturally less favoured areas (LFA in Slovenia were analyzed for the period 1981–2010. Following the instructions of European Commission prepared by Joint Research Centre (JRC 30-years averages of low air temperatures criteria (the vegetation period duration and sums of effective air temperatures and aridity criteria (aridity index AI have to be calculated. Calculations were additionally done using Slovenian Environment Agency (ARSO method, which is slightly different when determining temperature thresholds. Only hilly areas are below the LFA low air temperatures threshold with the lowest located meteorological station in Rateče. According to aridity criteria no area in Slovenia is below the threshold, so meteorological water balance was also examined. Average water balance in the period 1981–2010 was in most of locations lower than in the period 1971–2000. Climate change impacts are already expressed as trend presence in time series of studied variables, so it is recommended to calculate trends and take them into account or to perform regular iterations of calculations.

Big Area Additive Manufacturing of High Performance Bonded NdFeB Magnets.

Science.gov (United States)

Li, Ling; Tirado, Angelica; Nlebedim, I C; Rios, Orlando; Post, Brian; Kunc, Vlastimil; Lowden, R R; Lara-Curzio, Edgar; Fredette, Robert; Ormerod, John; Lograsso, Thomas A; Paranthaman, M Parans

2016-10-31

Additive manufacturing allows for the production of complex parts with minimum material waste, offering an effective technique for fabricating permanent magnets which frequently involve critical rare earth elements. In this report, we demonstrate a novel method - Big Area Additive Manufacturing (BAAM) - to fabricate isotropic near-net-shape NdFeB bonded magnets with magnetic and mechanical properties comparable or better than those of traditional injection molded magnets. The starting polymer magnet composite pellets consist of 65 vol% isotropic NdFeB powder and 35 vol% polyamide (Nylon-12). The density of the final BAAM magnet product reached 4.8 g/cm 3 , and the room temperature magnetic properties are: intrinsic coercivity H ci  = 688.4 kA/m, remanence B r  = 0.51 T, and energy product (BH) max  = 43.49 kJ/m 3 (5.47 MGOe). In addition, tensile tests performed on four dog-bone shaped specimens yielded an average ultimate tensile strength of 6.60 MPa and an average failure strain of 4.18%. Scanning electron microscopy images of the fracture surfaces indicate that the failure is primarily related to the debonding of the magnetic particles from the polymer binder. The present method significantly simplifies manufacturing of near-net-shape bonded magnets, enables efficient use of rare earth elements thus contributing towards enriching the supply of critical materials.

Identifying areas of high risk of human exposure to coccidioidomycosis in Texas using serology data from dogs.

Science.gov (United States)

Gautam, R; Srinath, I; Clavijo, A; Szonyi, B; Bani-Yaghoub, M; Park, S; Ivanek, R

2013-03-01

Coccidioidomycosis or Valley Fever (VF) is an emerging soil-borne fungal zoonosis affecting humans and animals. Most non-human cases of VF are found in dogs, which we hypothesize may serve as sentinels for estimating the human exposure risk. The objective of this study is to use the spatial and temporal distribution and clusters of dogs seropositive for VF to define the geographic area in Texas where VF is endemic, and thus presents a higher risk of exposure to humans. The included specimens were seropositive dogs tested at a major diagnostic laboratory between 1999 and 2009. Data were aggregated by zip code and smoothed by empirical Bayesian estimation to develop an isopleth map of VF seropositive rates using kriging. Clusters of seropositive dogs were identified using the spatial scan test. Both the isopleth map and the scan test identified an area with a high rate of VF-seropositive dogs in the western and southwestern parts of Texas (relative risk = 31). This location overlapped an area that was previously identified as a potential endemic region based on human surveys. Together, these data suggest that dogs may serve as sentinels for estimating the risk of human exposure to VF. © 2012 Blackwell Verlag GmbH.

Patterns of Seismicity Associated with USGS Identified Areas of Potentially Induced Seismicity.

Science.gov (United States)

Barnes, Caitlin; Halihan, Todd

2018-03-13

A systematic review across U.S. Geological Survey (USGS) identified potentially induced seismic locations was conducted to discover seismic distance patterns and trends over time away from injection disposal wells. Previous research indicates a 10 km (6 miles) average where the majority of induced seismicity is expected to occur within individual locations, with some areas reporting a larger radius of 35 km (22 miles) to over 70 km (43 miles). This research analyzed earthquake occurrences within nine USGS locations where specified wells were identified as contributors to induced seismicity to determine distance patterns from disposal wells or outward seismic migration over time using established principles of hydrogeology. Results indicate a radius of 31.6 km (20 miles) where 90% of felt earthquakes occur among locations, with the closest proximal felt seismic events, on average, occurring 3 km (1.9 miles) away from injection disposal wells. The results of this research found distance trends across multiple locations of potentially induced seismicity. © 2018, National Ground Water Association.

The use of load patterns to identify residential customers in a chosen area

Energy Technology Data Exchange (ETDEWEB)

Michalik, G.; Lech, M.; Mielczarski, W. [Monash Univ., Clayton, VIC (Australia). Centre for Electrical Power Engineering

1995-12-31

Information on customers` categories and energy use patterns is a basis for the development of any Demand Side Management program. This paper presents an application of energy consumption patterns to identification of customers in a chosen area. Customers have been segmented into four main categories with six subgroups in each category. A total pattern of energy use can be achieved by the combination of characteristic patterns for each subgroup with multiplication by the number of customers in each subgroup. The paper proposes to apply characteristic patterns developed and nonlinear programming techniques to identify customers in a chosen area from patterns measured at distribution feeders. The procedure can be applied as an alternative to surveys and measurements at the mains of particular customers but may also be implemented as an accompanying system to verify results from other procedures of customer identification. (author). 1 tab., 6 figs., 4 refs.

Implementing the South African additive manufacturing technology roadmap - the role of an additive manufacturing centre of competence

Directory of Open Access Journals (Sweden)

Du Preez, Willie Bouwer

2015-08-01

Full Text Available The Rapid Product Development Association of South Africa (RAPDASA expressed the need for a national Additive Manufacturing Roadmap. Consequentially, the South African Department of Science and Technology commissioned the development of a South African Additive Manufacturing Technology Roadmap. This was intended to guide role-players in identifying business opportunities, addressing technology gaps, focusing development programmes, and informing investment decisions that would enable local companies and industry sectors to become global leaders in selected areas of additive manufacturing. The challenge remains now for South Africa to decide on an implementation approach that will maximize the impact in the shortest possible time. This article introduces the concept of a national Additive Manufacturing Centre of Competence (AMCoC as a primary implementation vehicle for the roadmap. The support of the current leading players in additive manufacturing in South Africa for such a centre of competence is shared and their key roles are indicated. A summary of the investments that the leading players have already made in the focus areas of the AMCoC over the past two decades is given as confirmation of their commitment towards the advancement of the additive manufacturing technology. An exposition is given of how the AMCoC could indeed become the primary initiative for achieving the agreed national goals on additive manufacturing. The conclusion is that investment by public and private institutions in an AMCoC would be the next step towards ensuring South Africa’s continued progress in the field.

Development of a predictive methodology for identifying high radon exhalation potential areas

International Nuclear Information System (INIS)

Ielsch, G.

2001-01-01

Radon 222 is a radioactive natural gas originating from the decay of radium 226 which itself originates from the decay of uranium 23 8 naturally present in rocks and soil. Inhalation of radon gas and its decay products is a potential health risk for man. Radon can accumulate in confined environments such as buildings, and is responsible for one third of the total radiological exposure of the general public to radiation. The problem of how to manage this risk then arises. The main difficulty encountered is due to the large variability of exposure to radon across the country. A prediction needs to be made of areas with the highest density of buildings with high radon levels. Exposure to radon varies depending on the degree of confinement of the habitat, the lifestyle of the occupants and particularly emission of radon from the surface of the soil on which the building is built. The purpose of this thesis is to elaborate a methodology for determining areas presenting a high potential for radon exhalation at the surface of the soil. The methodology adopted is based on quantification of radon exhalation at the surface, starting from a precise characterization of the main local geological and pedological parameters that control the radon source and its transport to the ground/atmosphere interface. The methodology proposed is innovative in that it combines a cartographic analysis, parameters integrated into a Geographic Information system, and a simplified model for vertical transport of radon by diffusion through pores in the soil. This methodology has been validated on two typical areas, in different geological contexts, and gives forecasts that generally agree with field observations. This makes it possible to identify areas with a high exhalation potential within a range of a few square kilometers. (author)

Feasibility of using Big Area Additive Manufacturing to Directly Manufacture Boat Molds

Energy Technology Data Exchange (ETDEWEB)

Post, Brian K. [ORNL; Chesser, Phillip C. [ORNL; Lind, Randall F. [ORNL; Sallas, Matthew R. [ORNL; Love, Lonnie J. [ORNL

2018-01-01

The goal of this project was to explore the feasibility of using Big Area Additive Manufacturing (BAAM) to directly manufacture a boat mold without the need for coatings. All prior tooling projects with BAAM required the use to thick coatings to overcome the surface finish limitations of the BAAM process. While the BAAM process significantly lowers the cost of building the mold, the high cost element rapidly became the coatings (cost of the material, labor on coating, and finishing). As an example, the time and cost to manufacture the molds for the Wind Turbine project with TPI Composites Inc. and the molds for the submarine project with Carderock Naval Warfare Systems was a fraction of the time and cost of the coatings. For this project, a catamaran boat hull mold was designed, manufactured, and assembled with an additional 0.15” thickness of material on all mold surfaces. After printing, the mold was immediately machined and assembled. Alliance MG, LLC (AMG), the industry partner of this project, experimented with mold release agents on the carbon-fiber reinforced acrylonitrile butadiene styrene (CF ABS) to verify that the material can be directly used as a mold (rather than needing a coating). In addition, for large molds (such as the wind turbine mold with TPI Composites Inc.), the mold only provided the target surface. A steel subframe had to be manufactured to provide structural integrity. If successful, this will significantly reduce the time and cost necessary for manufacturing large resin infusion molds using the BAAM process.

Synthesis and characterization of high-surface-area millimeter-sized silica beads with hierarchical multi-modal pore structure by the addition of agar

Energy Technology Data Exchange (ETDEWEB)

Han, Yosep; Choi, Junhyun [Department of Mineral Resources and Energy Engineering, Chonbuk National University, 567 Baekje-daero, Deokjin-gu, Jeonju-si, Jeollabuk-do 561–756 (Korea, Republic of); Tong, Meiping, E-mail: tongmeiping@iee.pku.edu.cn [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, College of Environmental Sciences and Engineering, Peking University, Beijing 100871 (China); Kim, Hyunjung, E-mail: kshjkim@jbnu.ac.kr [Department of Mineral Resources and Energy Engineering, Chonbuk National University, 567 Baekje-daero, Deokjin-gu, Jeonju-si, Jeollabuk-do 561–756 (Korea, Republic of)

2014-04-01

Millimeter-sized spherical silica foams (SSFs) with hierarchical multi-modal pore structure featuring high specific surface area and ordered mesoporous frameworks were successfully prepared using aqueous agar addition, foaming and drop-in-oil processes. The pore-related properties of the prepared spherical silica (SSs) and SSFs were systematically characterized by field emission-scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), small-angle X-ray diffraction (SAXRD), Hg intrusion porosimetry, and N{sub 2} adsorption–desorption isotherm measurements. Improvements in the BET surface area and total pore volume were observed at 504 m{sup 2} g{sup −1} and 5.45 cm{sup 3} g{sup −1}, respectively, after an agar addition and foaming process. Despite the increase in the BET surface area, the mesopore wall thickness and the pore size of the mesopores generated from the block copolymer with agar addition were unchanged based on the SAXRD, TEM, and BJH methods. The SSFs prepared in the present study were confirmed to have improved BET surface area and micropore volume through the agar loading, and to exhibit interconnected 3-dimensional network macropore structure leading to the enhancement of total porosity and BET surface area via the foaming process. - Highlights: • Millimeter-sized spherical silica foams (SSFs) are successfully prepared. • SSFs exhibit high BET surface area and ordered hierarchical pore structure. • Agar addition improves BET surface area and micropore volume of SSFs. • Foaming process generates interconnected 3-D network macropore structure of SSFs.

Coherent addition of high power broad-area laser diodes with a compact VBG V-shaped external Talbot cavity

Science.gov (United States)

Liu, Bo; Braiman, Yehuda

2018-05-01

We introduced a compact V-shaped external Talbot cavity for phase locking of high power broad-area laser diodes. The length of compact cavity is ∼25 mm. Near diffraction-limit coherent addition of 10 broad-area laser diodes indicated that high quality phase locking was achieved. We measured the near-field emission mode of each individual broad-area laser diode with different feedback, such as a volume Bragg grating and a high reflection mirror. We found out that the best result of phase locking broad-area laser diodes was achieved by the compact V-shaped external Talbot cavity with volume Bragg grating feedback.

Using a distribution and conservation status weighted hotspot approach to identify areas in need of conservation action to benefit Idaho bird species

Science.gov (United States)

Haines, Aaron M.; Leu, Matthias; Svancara, Leona K.; Wilson, Gina; Scott, J. Michael

2010-01-01

Identification of biodiversity hotspots (hereafter, hotspots) has become a common strategy to delineate important areas for wildlife conservation. However, the use of hotspots has not often incorporated important habitat types, ecosystem services, anthropogenic activity, or consistency in identifying important conservation areas. The purpose of this study was to identify hotspots to improve avian conservation efforts for Species of Greatest Conservation Need (SGCN) in the state of Idaho, United States. We evaluated multiple approaches to define hotspots and used a unique approach based on weighting species by their distribution size and conservation status to identify hotspot areas. All hotspot approaches identified bodies of water (Bear Lake, Grays Lake, and American Falls Reservoir) as important hotspots for Idaho avian SGCN, but we found that the weighted approach produced more congruent hotspot areas when compared to other hotspot approaches. To incorporate anthropogenic activity into hotspot analysis, we grouped species based on their sensitivity to specific human threats (i.e., urban development, agriculture, fire suppression, grazing, roads, and logging) and identified ecological sections within Idaho that may require specific conservation actions to address these human threats using the weighted approach. The Snake River Basalts and Overthrust Mountains ecological sections were important areas for potential implementation of conservation actions to conserve biodiversity. Our approach to identifying hotspots may be useful as part of a larger conservation strategy to aid land managers or local governments in applying conservation actions on the ground.

Predicting survival function and identifying associated factors in patients with renal insufficiency in the metropolitan area of Maringá, Paraná State, Brazil.

Science.gov (United States)

Ramires, Thiago G; Nakamura, Luiz R; Righetto, Ana J; Ortega, Edwin M M; Cordeiro, Gauss M

2018-02-05

Renal insufficiency is a serious medical and public health problem worldwide. Recently, although many surveys have been developed to identify factors related to the lifetime of patients with renal insufficiency, controversial results from several studies suggest that researches should be conducted by region. Thus, in this study we aim to predict and identify factors associated with the lifetime of patients with chronic renal failure (CRF) in the metropolitan area of Maringá, Paraná State, Brazil, based on the generalized additive models for location, scale and shape (GAMLSS) framework. Data used in this study were collected from the Maringá Kidney Institute and comprehends 177 patients (classified with CRF and mostly being treated under the Brazilian Unified National Health System) enrolled in a hemodialysis program from 1978 up to 2010. By using this approach, we concluded that in other regions, gender, kidney transplant indicator, antibodies to hepatitis B and antibodies to hepatitis C are significant factors that affect the expected lifetime.

Predicting survival function and identifying associated factors in patients with renal insufficiency in the metropolitan area of Maringá, Paraná State, Brazil

Directory of Open Access Journals (Sweden)

Thiago G. Ramires

2018-02-01

Full Text Available Renal insufficiency is a serious medical and public health problem worldwide. Recently, although many surveys have been developed to identify factors related to the lifetime of patients with renal insufficiency, controversial results from several studies suggest that researches should be conducted by region. Thus, in this study we aim to predict and identify factors associated with the lifetime of patients with chronic renal failure (CRF in the metropolitan area of Maringá, Paraná State, Brazil, based on the generalized additive models for location, scale and shape (GAMLSS framework. Data used in this study were collected from the Maringá Kidney Institute and comprehends 177 patients (classified with CRF and mostly being treated under the Brazilian Unified National Health System enrolled in a hemodialysis program from 1978 up to 2010. By using this approach, we concluded that in other regions, gender, kidney transplant indicator, antibodies to hepatitis B and antibodies to hepatitis C are significant factors that affect the expected lifetime.

A Spatial Approach to Identify Slum Areas in East Wara Sub-Districts, South Sulawesi

Science.gov (United States)

Anurogo, W.; Lubis, M. Z.; Pamungkas, D. S.; Hartono; Ibrahim, F. M.

2017-12-01

Spatial approach is one of the main approaches of geography, its analysis emphasizes the existence of space that serves to accommodate human activities. The dynamic development of the city area brings many impacts to the urban community’s own life patterns. The development of the city center which is the center of economic activity becomes the attraction for the community that can bring influence to the high flow of labor both from within the city itself and from outside the city area, thus causing the high flow of urbanization. Urbanization has caused an explosion in urban population and one implication is the occurrence of labor-clumping in major cities in Indonesia. Another impact of the high urbanization flow of cities is the problem of urban settlements. The more populations that come in the city, the worse the quality of the existing settlements in the city if not managed properly. This study aims to determine the location of slum areas in East Wara Sub-Districts using remote sensing technology tools and Geographic Information System (GIS). Parameters used to identify slum areas partially extracted using remote sensing data and for parameters that cannot be extracted using remote sensing data, information obtained from field surveys with information retrieval based on reference data. Analysis results for slum settlements taken from the parameters indicate that the East Wara Sub-District has the largest slum areas located in Pontap village. The village of Pontap has two classes of slums that are very shabby and slums. Slum classes are also in Surutangga Village. The result of the analysis shows that the slum settlement area has 46,324 Ha, which is only located in Pontap Village, whereas for the slum class are found in some villages of Pontap and Surutangga Urban Village, there are 37.797 Ha area. The class of slum settlement areas has the largest proportion of the area among other classes in East Wara Subdistrict. The class of slum settlement areas has an

Odour and flavour thresholds of gasoline additives (MTBE, ETBE and TAME) and their occurrence in Dutch drinking water collection areas

NARCIS (Netherlands)

van Wezel, A.; Puijker, L.; Vink, C.; Versteegh, A.; de Voogt, P.

2009-01-01

The use of ETBE (ethyl-tert-butylether) as gasoline additive has recently grown rapidly. Contamination of aquatic systems is well documented for MTBE (methyl-tert-butylether), but less for other gasoline additives. Due to their mobility they may easily reach drinking water collection areas. Odour

Usefulness of Epicardial Area in the Short Axis to Identify Elevated Left Ventricular Mass in Men.

Science.gov (United States)

Fitzpatrick, Jesse K; Cohen, Beth E; Rosenblatt, Andrew; Shaw, Richard E; Schiller, Nelson B

2018-06-15

Left ventricular (LV) hypertrophy is strongly associated with increased cardiovascular morbidity and mortality. The 2-dimensional LV mass algorithms suffer from measurement variability that can lead to misclassification of patients with LV hypertrophy as normal, or vice versa. Among the 4 echocardiographic measurements required by the 2-dimensional LV mass algorithms, epicardial and endocardial area have the lowest interobserver variation and could be used to corroborate LV mass calculations. We sought cut-off values that are able to discriminate between elevated and normal LV mass based on endocardial or epicardial area alone. Using data from 664 men enrolled in the Mind Your Heart Study, we calculated the correlation of LV mass index with epicardial area and endocardial area. We then used receiver operator characteristic curves to identify epicardial and endocardial area cut-points that could discriminate subjects with normal LV mass and LV hypertrophy. LV mass index was more strongly correlated with epicardial area compared with endocardial area, r = 0.70 versus r = 0.27, respectively. Epicardial area had a significantly higher area under the receiver operator characteristic curve (p versus 0.63 (95% confidence interval 0.57 to 0.71). An epicardial area cut-point of ≥38.0 cm 2 corresponded to a sensitivity of 95.0% and specificity of 54.4% for detecting LV hypertrophy. In conclusion, epicardial area showed promise as a method of rapid screening for LV hypertrophy and could be used to validate formal LV mass calculations. Copyright © 2018 Elsevier Inc. All rights reserved.

Use of strontium isotopes to identify buried water main leakage into groundwater in a highly urbanized coastal area.

Science.gov (United States)

Leung, Chi-Man; Jiao, Jiu Jimmy

2006-11-01

Previous studies indicate that the local aquifer systems in the Mid-Levels, a highly urbanized coastal area in Hong Kong, have commonly been affected by leakage from water mains. The identification of leakage locations was done by conventional water quality parameters including major and trace elements. However, these parameters may lead to ambiguous results and fail to identify leakage locations especially where the leakage is from drinking water mains because the chemical composition of drinking water is similar to that of natural groundwater. In this study, natural groundwater, seepage in the developed spaces, leakage from water mains, and parent aquifer materials were measured for strontium isotope (87Sr/86Sr) compositions to explore the feasibility of using these ratios to better constrain the seepage sources. The results show that the 87Sr/86Sr ratios of natural groundwater and leakage from water mains are distinctly different and thus, they can provide additional information on the sources of seepage in developed spaces. A classification system based on the aqueous 87Sr/86Sr ratio is proposed for seepage source identification.

Biochemometrics to Identify Synergists and Additives from Botanical Medicines: A Case Study with Hydrastis canadensis (Goldenseal).

Science.gov (United States)

Britton, Emily R; Kellogg, Joshua J; Kvalheim, Olav M; Cech, Nadja B

2018-03-23

A critical challenge in the study of botanical natural products is the difficulty of identifying multiple compounds that may contribute additively, synergistically, or antagonistically to biological activity. Herein, it is demonstrated how combining untargeted metabolomics with synergy-directed fractionation can be effective toward accomplishing this goal. To demonstrate this approach, an extract of the botanical goldenseal ( Hydrastis canadensis) was fractionated and tested for its ability to enhance the antimicrobial activity of the alkaloid berberine (4) against the pathogenic bacterium Staphylococcus aureus. Bioassay data were combined with untargeted mass spectrometry-based metabolomics data sets (biochemometrics) to produce selectivity ratio (SR) plots, which visually show which extract components are most strongly associated with the biological effect. Using this approach, the new flavonoid 3,3'-dihydroxy-5,7,4'-trimethoxy-6,8- C-dimethylflavone (29) was identified, as were several flavonoids known to be active. When tested in combination with 4, 29 lowered the IC 50 of 4 from 132.2 ± 1.1 μM to 91.5 ± 1.1 μM. In isolation, 29 did not demonstrate antimicrobial activity. The current study highlights the importance of fractionation when utilizing metabolomics for identifying bioactive components from botanical extracts and demonstrates the power of SR plots to help merge and interpret complex biological and chemical data sets.

Retail tobacco exposure: using geographic analysis to identify areas with excessively high retail density.

Science.gov (United States)

Rodriguez, Daniel; Carlos, Heather A; Adachi-Mejia, Anna M; Berke, Ethan M; Sargent, James

2014-02-01

There is great disparity in tobacco outlet density (TOD), with density highest in low-income areas and areas with greater proportions of minority residents, and this disparity may affect cancer incidence. We sought to better understand the nature of this disparity by assessing how these socio-demographic factors relate to TOD at the national level. Using mixture regression analysis and all of the nearly 65,000 census tracts in the contiguous United States, we aimed to determine the number of latent disparity classes by modeling the relations of proportions of Blacks, Hispanics, and families living in poverty with TOD, controlling for urban/rural status. We identified six disparity classes. There was considerable heterogeneity in relation to TOD for Hispanics in rural settings. For Blacks, there was no relation to TOD in an urban moderate disparity class, and for rural census tracts, the relation was highest in a moderate disparity class. We demonstrated the utility of classifying census tracts on heterogeneity of tobacco risk exposure. This approach provides a better understanding of the complexity of socio-demographic influences of tobacco retailing and creates opportunities for policy makers to more efficiently target areas in greatest need.

Identifying desertification risk areas using fuzzy membership and geospatial technique - A case study, Kota District, Rajasthan

Science.gov (United States)

Dasgupta, Arunima; Sastry, K. L. N.; Dhinwa, P. S.; Rathore, V. S.; Nathawat, M. S.

2013-08-01

Desertification risk assessment is important in order to take proper measures for its prevention. Present research intends to identify the areas under risk of desertification along with their severity in terms of degradation in natural parameters. An integrated model with fuzzy membership analysis, fuzzy rule-based inference system and geospatial techniques was adopted, including five specific natural parameters namely slope, soil pH, soil depth, soil texture and NDVI. Individual parameters were classified according to their deviation from mean. Membership of each individual values to be in a certain class was derived using the normal probability density function of that class. Thus if a single class of a single parameter is with mean μ and standard deviation σ, the values falling beyond μ + 2 σ and μ - 2 σ are not representing that class, but a transitional zone between two subsequent classes. These are the most important areas in terms of degradation, as they have the lowest probability to be in a certain class, hence highest probability to be extended or narrowed down in next or previous class respectively. Eventually, these are the values which can be easily altered, under extrogenic influences, hence are identified as risk areas. The overall desertification risk is derived by incorporating the different risk severity of each parameter using fuzzy rule-based interference system in GIS environment. Multicriteria based geo-statistics are applied to locate the areas under different severity of desertification risk. The study revealed that in Kota, various anthropogenic pressures are accelerating land deterioration, coupled with natural erosive forces. Four major sources of desertification in Kota are, namely Gully and Ravine erosion, inappropriate mining practices, growing urbanization and random deforestation.

The availability of hydrogeologic data associated with areas identified by the US Geological Survey as experiencing potentially induced seismicity resulting from subsurface injection

Science.gov (United States)

Barnes, Caitlin; Halihan, Todd

2018-05-01

A critical need exists for site-specific hydrogeologic data in order to determine potential hazards of induced seismicity and to manage risk. By 2015, the United States Geological Survey (USGS) had identified 17 locations in the USA that are experiencing an increase in seismicity, which may be potentially induced through industrial subsurface injection. These locations span across seven states, which vary in geological setting, industrial exposure and seismic history. Comparing the research across the 17 locations revealed patterns for addressing induced seismicity concerns, despite the differences between geographical locations. Most induced seismicity studies evaluate geologic structure and seismic data from areas experiencing changes in seismic activity levels, but the inherent triggering mechanism is the transmission of hydraulic pressure pulses. This research conducted a systematic review of whether data are available in these locations to generate accurate hydrogeologic predictions, which could aid in managing seismicity. After analyzing peer-reviewed research within the 17 locations, this research confirms a lack of site-specific hydrogeologic data availability for at-risk areas. Commonly, formation geology data are available for these sites, but hydraulic parameters for the seismically active injection and basement zones are not available to researchers conducting peer-reviewed research. Obtaining hydrogeologic data would lead to better risk management for injection areas and provide additional scientific evidential support for determining a potentially induced seismic area.

A simple and successful sonographic technique to identify the sciatic nerve in the parasacral area.

Science.gov (United States)

Taha, Ahmad Muhammad

2012-03-01

The purpose of this study was to describe detailed sonographic anatomy of the parasacral area for rapid and successful identification of the sciatic nerve. Fifty patients scheduled for knee surgery were included in this observational study. An ultrasound-guided parasacral sciatic nerve block was performed in all patients. The ultrasound probe was placed on an axial plane 8 cm lateral to the uppermost point of the gluteal cleft. Usually, at this level the posterior border of the ischium (PBI), a characteristically curved hyperechoic line, could be identified. The sciatic nerve appeared as a hyperechoic structure just medial to the PBI. The nerve lies deep to the piriformis muscle lateral to the inferior gluteal vessels, and if followed caudally, it rests directly on the back of the ischium. After confirmation with electrical stimulation, a 20-mL mixture of 1% ropivacaine and 1% lidocaine with epinephrine was injected. The sciatic nerve was identified successfully in 48 patients (96%). In those patients, the median time required for its ultrasonographic identification was ten seconds [interquartile range, 8-13.7 sec], and the block success rate was 100%. The described sonographic details of the parasacral area allowed for rapid and successful identification of the sciatic nerve.

Identifying Priority Areas for Conservation: A Global Assessment for Forest-Dependent Birds

Science.gov (United States)

Buchanan, Graeme M.; Donald, Paul F.; Butchart, Stuart H. M.

2011-01-01

Limited resources are available to address the world's growing environmental problems, requiring conservationists to identify priority sites for action. Using new distribution maps for all of the world's forest-dependent birds (60.6% of all bird species), we quantify the contribution of remaining forest to conserving global avian biodiversity. For each of the world's partly or wholly forested 5-km cells, we estimated an impact score of its contribution to the distribution of all the forest bird species estimated to occur within it, and so is proportional to the impact on the conservation status of the world's forest-dependent birds were the forest it contains lost. The distribution of scores was highly skewed, a very small proportion of cells having scores several orders of magnitude above the global mean. Ecoregions containing the highest values of this score included relatively species-poor islands such as Hawaii and Palau, the relatively species-rich islands of Indonesia and the Philippines, and the megadiverse Atlantic Forests and northern Andes of South America. Ecoregions with high impact scores and high deforestation rates (2000–2005) included montane forests in Cameroon and the Eastern Arc of Tanzania, although deforestation data were not available for all ecoregions. Ecoregions with high impact scores, high rates of recent deforestation and low coverage by the protected area network included Indonesia's Seram rain forests and the moist forests of Trinidad and Tobago. Key sites in these ecoregions represent some of the most urgent priorities for expansion of the global protected areas network to meet Convention on Biological Diversity targets to increase the proportion of land formally protected to 17% by 2020. Areas with high impact scores, rapid deforestation, low protection and high carbon storage values may represent significant opportunities for both biodiversity conservation and climate change mitigation, for example through Reducing Emissions from

Identifying priority areas for conservation: a global assessment for forest-dependent birds.

Directory of Open Access Journals (Sweden)

Graeme M Buchanan

Full Text Available Limited resources are available to address the world's growing environmental problems, requiring conservationists to identify priority sites for action. Using new distribution maps for all of the world's forest-dependent birds (60.6% of all bird species, we quantify the contribution of remaining forest to conserving global avian biodiversity. For each of the world's partly or wholly forested 5-km cells, we estimated an impact score of its contribution to the distribution of all the forest bird species estimated to occur within it, and so is proportional to the impact on the conservation status of the world's forest-dependent birds were the forest it contains lost. The distribution of scores was highly skewed, a very small proportion of cells having scores several orders of magnitude above the global mean. Ecoregions containing the highest values of this score included relatively species-poor islands such as Hawaii and Palau, the relatively species-rich islands of Indonesia and the Philippines, and the megadiverse Atlantic Forests and northern Andes of South America. Ecoregions with high impact scores and high deforestation rates (2000-2005 included montane forests in Cameroon and the Eastern Arc of Tanzania, although deforestation data were not available for all ecoregions. Ecoregions with high impact scores, high rates of recent deforestation and low coverage by the protected area network included Indonesia's Seram rain forests and the moist forests of Trinidad and Tobago. Key sites in these ecoregions represent some of the most urgent priorities for expansion of the global protected areas network to meet Convention on Biological Diversity targets to increase the proportion of land formally protected to 17% by 2020. Areas with high impact scores, rapid deforestation, low protection and high carbon storage values may represent significant opportunities for both biodiversity conservation and climate change mitigation, for example through Reducing

Identifying priority areas for conservation: a global assessment for forest-dependent birds.

Science.gov (United States)

Buchanan, Graeme M; Donald, Paul F; Butchart, Stuart H M

2011-01-01

Limited resources are available to address the world's growing environmental problems, requiring conservationists to identify priority sites for action. Using new distribution maps for all of the world's forest-dependent birds (60.6% of all bird species), we quantify the contribution of remaining forest to conserving global avian biodiversity. For each of the world's partly or wholly forested 5-km cells, we estimated an impact score of its contribution to the distribution of all the forest bird species estimated to occur within it, and so is proportional to the impact on the conservation status of the world's forest-dependent birds were the forest it contains lost. The distribution of scores was highly skewed, a very small proportion of cells having scores several orders of magnitude above the global mean. Ecoregions containing the highest values of this score included relatively species-poor islands such as Hawaii and Palau, the relatively species-rich islands of Indonesia and the Philippines, and the megadiverse Atlantic Forests and northern Andes of South America. Ecoregions with high impact scores and high deforestation rates (2000-2005) included montane forests in Cameroon and the Eastern Arc of Tanzania, although deforestation data were not available for all ecoregions. Ecoregions with high impact scores, high rates of recent deforestation and low coverage by the protected area network included Indonesia's Seram rain forests and the moist forests of Trinidad and Tobago. Key sites in these ecoregions represent some of the most urgent priorities for expansion of the global protected areas network to meet Convention on Biological Diversity targets to increase the proportion of land formally protected to 17% by 2020. Areas with high impact scores, rapid deforestation, low protection and high carbon storage values may represent significant opportunities for both biodiversity conservation and climate change mitigation, for example through Reducing Emissions from

Acoustic Impedance Inversion To Identify Oligo-Miocene Carbonate Facies As Reservoir At Kangean Offshore Area

Science.gov (United States)

Zuli Purnama, Arif; Ariyani Machmud, Pritta; Eka Nurcahya, Budi; Yusro, Miftahul; Gunawan, Agung; Rahmadi, Dicky

2018-03-01

Model based inversion was applied to inversion process of 2D seismic data in Kangean Offshore Area. Integration acoustic impedance from wells and seismic data was expected showing physical property, facies separation and reservoir quality of carbonate rock, particularly in Kangean Offshore Area. Quantitative and qualitative analysis has been conducted on the inversion results to characterize the carbonate reservoir part of Kujung and correlate it to depositional facies type. Main target exploration in Kangean Offshore Area is Kujung Formation (Oligo-Miocene Carbonate). The type of reservoir in this area generate from reef growing on the platform. Carbonate rock is a reservoir which has various type and scale of porosity. Facies determination is required to to predict reservoir quality, because each facies has its own porosity value. Acoustic impedance is used to identify and characterize Kujung carbonate facies, also could be used to predict the distribution of porosity. Low acoustic impedance correlated with packstone facies that has acoustic impedance value below 7400 gr/cc*m/s. In other situation, high acoustic impedance characterized by wackestone facies above 7400 gr/cc*m/s. The interpretation result indicated that Kujung carbonate rock dominated by packstone facies in the upper part of build-up and it has ideal porosity for hydrocarbon reservoir.

Indeterminate solid hepatic lesions identified on non-diagnostic contrast-enhanced computed tomography: Assessment of the additional diagnostic value of contrast-enhanced ultrasound in the non-cirrhotic liver

International Nuclear Information System (INIS)

Quaia, Emilio; De Paoli, Luca; Angileri, Roberta; Cabibbo, Biagio; Cova, Maria Assunta

2014-01-01

Objective: To assess the additional diagnostic value of contrast-enhanced ultrasound (CEUS) in the characterization of indeterminate solid hepatic lesions identified on non-diagnostic contrast-enhanced computed tomography (CT). Methods: Fifty-five solid hepatic lesions (1–4 cm in diameter) in 46 non-cirrhotic patients (26 female, 20 male; age ± SD, 55 ± 10 years) underwent CEUS after being detected on contrast-enhanced CT which was considered as non-diagnostic after on-site analysis. Two blinded independent readers assessed CT and CEUS scans and were asked to classify retrospectively each lesion as a malignant or benign based on reference diagnostic criteria for the different hepatic lesion histotypes. Diagnostic accuracy and confidence (area – A z – under ROC curve) were assessed by using gadobenate dimeglumine-enhanced magnetic resonance (MR) imaging (n = 30 lesions), histology (n = 7 lesions), or US follow-up (n = 18 lesions) as the reference standards. Results: Final diagnoses included 29 hemangiomas, 3 focal nodular hyperplasias, 1 hepatocellular adenoma, and 22 metastases. The additional review of CEUS after CT images improved significantly (P < .05) the diagnostic accuracy (before vs after CEUS review = 49% [20/55] vs 89% [49/55] – reader 1 and 43% [24/55] vs 92% [51/55] – reader 2) and confidence (A z , 95% Confidence Intervals before vs after CEUS review = .773 [.652–.895] vs .997 [.987–1] – reader 1 and .831 [.724–.938] vs .998 [.992–1] – reader 2). Conclusions: CEUS improved the characterization of indeterminate solid hepatic lesions identified on non-diagnostic contrast-enhanced CT by identifying some specific contrast enhancement patterns.

Coculture with astrocytes reduces the radiosensitivity of glioblastoma stem-like cells and identifies additional targets for radiosensitization

International Nuclear Information System (INIS)

Rath, Barbara H; Wahba, Amy; Camphausen, Kevin; Tofilon, Philip J

2015-01-01

Toward developing a model system for investigating the role of the microenvironment in the radioresistance of glioblastoma (GBM), human glioblastoma stem-like cells (GSCs) were grown in coculture with human astrocytes. Using a trans-well assay, survival analyses showed that astrocytes significantly decreased the radiosensitivity of GSCs compared to standard culture conditions. In addition, when irradiated in coculture, the initial level of radiation-induced γH2AX foci in GSCs was reduced and foci dispersal was enhanced suggesting that the presence of astrocytes influenced the induction and repair of DNA double-strand breaks. These data indicate that astrocytes can decrease the radiosensitivity of GSCs in vitro via a paracrine-based mechanism and further support a role for the microenvironment as a determinant of GBM radioresponse. Chemokine profiling of coculture media identified a number of bioactive molecules not present under standard culture conditions. The gene expression profiles of GSCs grown in coculture were significantly different as compared to GSCs grown alone. These analyses were consistent with an astrocyte-mediated modification in GSC phenotype and, moreover, suggested a number of potential targets for GSC radiosensitization that were unique to coculture conditions. Along these lines, STAT3 was activated in GSCs grown with astrocytes; the JAK/STAT3 inhibitor WP1066 enhanced the radiosensitivity of GSCs under coculture conditions and when grown as orthotopic xenografts. Further, this coculture system may also provide an approach for identifying additional targets for GBM radiosensitization

Identifying the Entrepreneurship Characteristics of the Oil Palm Community Plantation Farmers in the Riau Area

OpenAIRE

Brilliant Asmit; Deddy P. Koesrindartoto

2015-01-01

Oil palm is an essential and strategic commodity in the Riau area because of its considerable role in supporting the peoples’ economy, especially for plantation farmers. Oil palm plantation activities have brought economic impacts to society there, both for the people who are directly involved with the plantations and for their surrounding communities. This regional advantage is a facility for farmers to be able to develop their farms as plantations. The aims of this research are to identify ...

Identifying core habitat and connectivity for focal species in the interior cedar-hemlock forest of North America to complete a conservation area design

Science.gov (United States)

Lance Craighead; Baden Cross

2007-01-01

To identify the remaining areas of the Interior Cedar- Hemlock Forest of North America and prioritize them for conservation planning, the Craighead Environmental Research Institute has developed a 2-scale method for mapping critical habitat utilizing 1) a broad-scale model to identify important regional locations as the basis for a Conservation Area Design (CAD), and 2...

Strategy paper. Remedial design/remedial action 100 Area. Revision 1

International Nuclear Information System (INIS)

Donahoe, R.L.

1995-07-01

The purpose of this planning document is to identify and define the approach for remedial design and remedial action (RD/RA) in the 100 Area of the Hanford Site, located in southeastern Washington State. Additionally, this document will support the Hanford Site Environmental Restoration Contract (ERC) team, the US Department of Energy (DOE), and regulatory agencies in identifying and agreeing upon the complete process for expedited cleanup of the 100 Area

Identifying Factors for Worker Motivation in Zambia's Rural Health Facilities.

Science.gov (United States)

Cross, Samuel S; Baernholdt, Dr Marianne

2017-01-01

Within Zambia there is a shortage of health workers in rural areas. This study aims to identify motivating factors for retaining rural health workers. Sixty rural health workers completed surveys and 46 were interviewed. They rated the importance of six motivating factors and discussed these and other factors in interviews. An interview was conducted with a Government Human Resources Manager (HR Manager) to elicit contextual information. All six factors were identified as being very important motivators, as were two additional factors. Additional career training was identified by many as the most important factor. Comparison of results and the HR Manager interview revealed that workers lacked knowledge about opportunities and that the HR manager was aware of barriers to career development. The Zambian government might better motivate and retain rural health workers by offering them any combination of identified factors, and by addressing the barriers to career development.

15 CFR 922.164 - Additional activity regulations by Sanctuary area.

Science.gov (United States)

2010-01-01

... plants may be possessed aboard a vessel in an Ecological Reserve or Sanctuary Preservation Area, provided... Sanctuary area. 922.164 Section 922.164 Commerce and Foreign Trade Regulations Relating to Commerce and... AND COASTAL RESOURCE MANAGEMENT NATIONAL MARINE SANCTUARY PROGRAM REGULATIONS Florida Keys National...

Mineral resource potential map of the Sugarloaf Roadless Area, San Bernardino County, California

Science.gov (United States)

Powell, Robert E.; Matti, Jonathan C.; Cox, Brett F.; Oliver, Howard W.; Wagini, Alexander; Campbell, Harry W.

1983-01-01

Geologic, geochemical, and geophysical investigations and a survey of mines and prospects indicate that the Sugaloaf Roadless Area contains subeconomic graphite and magnesian marble resources. Parts of the area have a low potential for the occurrence of additional low-grade graphite resources, but there is no potential for additional magnesian marble resources within the roadless area. Sand, gravel, and construction stone other than carbonate rocks are found in the roadless area, but similar or better quality materials are abundant and more accessible outside the area. The roadless area has no identified energy mineral resources, but parts of the area have a low to moderate potential for low-grade uranium resources. There are no identified metallic mineral resources within the area, and there is no evidence of a potential for the occurrence of such resources. No previously unknown mineral occurrence was located during this study.

Identifying the Entrepreneurship Characteristics of the Oil Palm Community Plantation Farmers in the Riau Area

Directory of Open Access Journals (Sweden)

Brilliant Asmit

2015-12-01

Full Text Available Oil palm is an essential and strategic commodity in the Riau area because of its considerable role in supporting the peoples’ economy, especially for plantation farmers. Oil palm plantation activities have brought economic impacts to society there, both for the people who are directly involved with the plantations and for their surrounding communities. This regional advantage is a facility for farmers to be able to develop their farms as plantations. The aims of this research are to identify the entrepreneurship characteristics of the oil palm farmers, and also to identify the entrepreneurship characteristics that differentiate the farmers, as seen from their business’ achievements. The research used a grounded theory approach to identify the characteristics of oil palm farmers systematically. The sampling method used for the research was theoretical sampling, which is data gathering driven by the concepts derived from the theory of previous entrepreneurship characteristics studies. The research object is the oil palm farmers in Riau, Indonesia. The results of the analysis identified the entrepreneurship characteristics of the oil palm farmers, they are growth oriented, risk-taking, innovative, with a sense of personal control, self confident, and cooperative. But, among the characteristics, only the characteristic of their cooperation did not differentiate the oil palm farmers in the achievement of their business activities.

Identifying spatially integrated floodplains/riparian areas and wetlands

Science.gov (United States)

Floodplain delineation may play an important role in managing wetlands and riparian areas at multiple scales - local, state, and federal. This poster demonstrates multiple GIS-based approaches to delimiting floodplains and contrasts these with observed flooding events from a majo...

Source Distribution Method for Unsteady One-Dimensional Flows With Small Mass, Momentum, and Heat Addition and Small Area Variation

Science.gov (United States)

Mirels, Harold

1959-01-01

A source distribution method is presented for obtaining flow perturbations due to small unsteady area variations, mass, momentum, and heat additions in a basic uniform (or piecewise uniform) one-dimensional flow. First, the perturbations due to an elemental area variation, mass, momentum, and heat addition are found. The general solution is then represented by a spatial and temporal distribution of these elemental (source) solutions. Emphasis is placed on discussing the physical nature of the flow phenomena. The method is illustrated by several examples. These include the determination of perturbations in basic flows consisting of (1) a shock propagating through a nonuniform tube, (2) a constant-velocity piston driving a shock, (3) ideal shock-tube flows, and (4) deflagrations initiated at a closed end. The method is particularly applicable for finding the perturbations due to relatively thin wall boundary layers.

Identifying areas under potential risk of illegal construction and demolition waste dumping using GIS tools.

Science.gov (United States)

Seror, Nissim; Portnov, Boris A

2018-05-01

Construction and demolition (C&D) waste, dumped illegally in ravines and open areas, contaminates soil and can cause underground water pollution and forests fires. Yet, effective monitoring of illegal C&D waste dumping and enforcing legislation against the offenders are often a difficult task due to the large size of geographic areas that need to be monitored, and limited human and financial resources available to environmental law enforcement agencies. In this study, we use Geographic Information System (GIS) tools and geo-statistical modelling to identify the areas under potentially elevated risk of illegal C&D waste dumping in the Haifa district of Israel. As our analysis shows, locational factors, significantly associated with the accumulated amount of waste in the existing illegal C&D waste sites, include: distance to the nearest main road, depth of the ravine present at the site (pwaste dumping for future monitoring. As we suggest, the proposed approach may be useful for environmental law enforcement authorities, by helping them to focus on specific sites for inspection, save resources, and act against the offenders more efficiently. Copyright © 2018 Elsevier Ltd. All rights reserved.

Additions and corrections to the bibliography of geologic studies, Columbia Plateau (Columbia River Besalt) and adjacent Areas, in Idaho, 1980

International Nuclear Information System (INIS)

Strowd, W.

1980-01-01

This bibliography is an update to Idaho Bureau of Mines and Geology Open-File Report 78-6, Bibliography of Geological Studies, Columbia Plateau (Columbia River Basalt Group) and adjacent areas in Idaho (also known as Rockwell Hanford Operations' contractor report RHO-BWI-C-44). To keep the original document current, this additions and corrections report was prepared for the Basalt Waste Isolation Project of Rockwell Hanford Operations. This update is supplementary; therefore, references cited in the original document have not been included here. What is included are materials that have become available since the original publication and pertinent literature that had originally been overlooked. Accompany this updated bubliography are index maps that show locations of geologic studies and geochemical petrographic, remanent paleomagnetic, and radiometric age-dated sites within the Columbia River Basalt Group field within Idaho; also identified are archeological sites, test wells, mines, quarries, and other types of excavations. References on the index maps are keyed to the bibliography and cover the Spokane, Pullman, Hamilton, Grangeville, Elk City, Baker, Boise, and Jordan Valley Army Map Service two-degree quadrangles

Identifying the Prospective Area of Sulfide Groundwater within the Area of Palvantash Oil and Gas Deposit

Directory of Open Access Journals (Sweden)

M. R. Zhurayev

2014-03-01

Full Text Available This paper describes the methodology of prospecting for sulfide groundwater in the area of Palvantash oil fields. In result of study allowed determining the favorable conditions for the sulfide waters formation, and mapping the areas of different sulfide water concentration. The relatively permeable areas were established and the water borehole positions were recommended.

Nominal group technique: a brainstorming tool for identifying areas to improve pain management in hospitalized patients.

Science.gov (United States)

Peña, Adolfo; Estrada, Carlos A; Soniat, Debbie; Taylor, Benjamin; Burton, Michael

2012-01-01

Pain management in hospitalized patients remains a priority area for improvement; effective strategies for consensus development are needed to prioritize interventions. To identify challenges, barriers, and perspectives of healthcare providers in managing pain among hospitalized patients. Qualitative and quantitative group consensus using a brainstorming technique for quality improvement-the nominal group technique (NGT). One medical, 1 medical-surgical, and 1 surgical hospital unit at a large academic medical center. Nurses, resident physicians, patient care technicians, and unit clerks. Responses and ranking to the NGT question: "What causes uncontrolled pain in your unit?" Twenty-seven health workers generated a total of 94 ideas. The ideas perceived contributing to a suboptimal pain control were grouped as system factors (timeliness, n = 18 ideas; communication, n = 11; pain assessment, n = 8), human factors (knowledge and experience, n = 16; provider bias, n = 8; patient factors, n = 19), and interface of system and human factors (standardization, n = 14). Knowledge, timeliness, provider bias, and patient factors were the top ranked themes. Knowledge and timeliness are considered main priorities to improve pain control. NGT is an efficient tool for identifying general and context-specific priority areas for quality improvement; teams of healthcare providers should consider using NGT to address their own challenges and barriers. Copyright © 2011 Society of Hospital Medicine.

Using geographic information systems to identify prospective marketing areas for a special library.

Science.gov (United States)

McConnaughy, Rozalynd P; Wilson, Steven P

2006-05-04

The Center for Disability Resources (CDR) Library is the largest collection of its kind in the Southeastern United States, consisting of over 5,200 books, videos/DVDs, brochures, and audiotapes covering a variety of disability-related topics, from autism to transition resources. The purpose of the library is to support the information needs of families, faculty, students, staff, and other professionals in South Carolina working with individuals with disabilities. The CDR Library is funded on a yearly basis; therefore, maintaining high usage is crucial. A variety of promotional efforts have been used to attract new patrons to the library. Anyone in South Carolina can check out materials from the library, and most of the patrons use the library remotely by requesting materials, which are then mailed to them. The goal of this project was to identify areas of low geographic usage as a means of identifying locations for future library marketing efforts. Nearly four years worth of library statistics were compiled in a spreadsheet that provided information per county on the number of checkouts, the number of renewals, and the population. Five maps were created using ArcView GIS software to create visual representations of patron checkout and renewal behavior per county. Out of the 46 counties in South Carolina, eight counties never checked out materials from the library. As expected urban areas and counties near the library's physical location have high usage totals. The visual representation of the data made identification of low usage regions easier than using a standalone database with no visual-spatial component. The low usage counties will be the focus of future Center for Disability Resources Library marketing efforts. Due to the impressive visual-spatial representations created with Geographic Information Systems, which more efficiently communicate information than stand-alone database information can, librarians may benefit from the software's use as a

Pork carcass injury in slaughterhouse waiting area and nutrient addition in pre-slaughter fasting

Directory of Open Access Journals (Sweden)

Tiago G Petrolli

2017-01-01

Full Text Available Objective. Two experiments were conducted on a slaughterhouse located in Brazil, which the first aimed at evaluating the injuries on pig skin and carcass resulting from slaughterhouse waiting area management and the second aimed at assessing how glucose (G, sodium bicarbonate (SB and vitamin E (VE added to water during pre-slaughter fasting may affect carcass yield, organ relative weight and pork meat quality characteristics. Materials and methods. First trial included 1000 pigs, which were observed in the slaughterhouse resting area until the moment they entered the stunning process area. In the second trial were used 500 animals distributed on the last pre-slaughter day in a completely randomized design, including ten treatments and ten replicates. The treatments were: water; 50 g/L G; 50 g/L G + 200 mg/L of VE; 75 g/L of G; 75 g/L of G + 200 mg VE; 0.45% SB; 0.45% SB + 200 mg/L of VE; 0.55% SB; 0.55% SB + 200 mg/L of VE; 200 mg/L of VE. Results. Carcass yield and relative organ weight were not affected by treatments. The addition of 0.55% SB + 200 mg VE reduced the final pH of meat, and of 0.45% SB reduced the red pigment intensity. Conclusions. The main occurrences of injuries to the skin and carcass of pigs are due to fights. Also, adding glucose, sodium bicarbonate, and vitamin E to diet did not affect the carcass and viscera yield and meat quality.

Using Range-Wide Abundance Modeling to Identify Key Conservation Areas for the Micro-Endemic Bolson Tortoise (Gopherus flavomarginatus.

Directory of Open Access Journals (Sweden)

Cinthya A Ureña-Aranda

Full Text Available A widespread biogeographic pattern in nature is that population abundance is not uniform across the geographic range of species: most occurrence sites have relatively low numbers, whereas a few places contain orders of magnitude more individuals. The Bolson tortoise Gopherus flavomarginatus is endemic to a small region of the Chihuahuan Desert in Mexico, where habitat deterioration threatens this species with extinction. In this study we combined field burrows counts and the approach for modeling species abundance based on calculating the distance to the niche centroid to obtain range-wide abundance estimates. For the Bolson tortoise, we found a robust, negative relationship between observed burrows abundance and distance to the niche centroid, with a predictive capacity of 71%. Based on these results we identified four priority areas for the conservation of this microendemic and threatened tortoise. We conclude that this approach may be a useful approximation for identifying key areas for sampling and conservation efforts in elusive and rare species.

Differential activation of an identified motor neuron and neuromodulation provide Aplysia's retractor muscle an additional function.

Science.gov (United States)

McManus, Jeffrey M; Lu, Hui; Cullins, Miranda J; Chiel, Hillel J

2014-08-15

To survive, animals must use the same peripheral structures to perform a variety of tasks. How does a nervous system employ one muscle to perform multiple functions? We addressed this question through work on the I3 jaw muscle of the marine mollusk Aplysia californica's feeding system. This muscle mediates retraction of Aplysia's food grasper in multiple feeding responses and is innervated by a pool of identified neurons that activate different muscle regions. One I3 motor neuron, B38, is active in the protraction phase, rather than the retraction phase, suggesting the muscle has an additional function. We used intracellular, extracellular, and muscle force recordings in several in vitro preparations as well as recordings of nerve and muscle activity from intact, behaving animals to characterize B38's activation of the muscle and its activity in different behavior types. We show that B38 specifically activates the anterior region of I3 and is specifically recruited during one behavior, swallowing. The function of this protraction-phase jaw muscle contraction is to hold food; thus the I3 muscle has an additional function beyond mediating retraction. We additionally show that B38's typical activity during in vivo swallowing is insufficient to generate force in an unmodulated muscle and that intrinsic and extrinsic modulation shift the force-frequency relationship to allow contraction. Using methods that traverse levels from individual neuron to muscle to intact animal, we show how regional muscle activation, differential motor neuron recruitment, and neuromodulation are key components in Aplysia's generation of multifunctionality. Copyright © 2014 the American Physiological Society.

Catch tanks inhibitor addition 200-East and 200-West Areas

International Nuclear Information System (INIS)

Palit, A.N.

1996-01-01

Reported is the study of 11 catch tanks in the 200-East Area and the 7 catch tanks in the 200-West Area listed as active. The location, capacity, material of construction, annual total accumulation, annual rain intrusion, waste transfer rate, and access for chemical injection in these tanks are documented. The present and future utilization and isolation plans for the catch tanks are established

Identifying sensitive areas on intercultural contacts: An exploratory study

Directory of Open Access Journals (Sweden)

Ignacio Ramos-Vidal

2011-06-01

Full Text Available This paper analyzes the negative influence that cultural friction areas can promote on intercultural contacts. First, we expose the critical incident method like cross-cultural training model (Arthur, 2001. Then we show the negative effects that sensitive cultural zones can exert on the formation of prejudices and stereotypes about culturally diverse groups, analyzing 77 critical incidents collected in two different formative contexts. The main cultural shock areas detected are a intercultural communication barriers, b gender roles, and c the cultural expressions statement. Strategies to improve the method validity are proposed.

Fault tree analysis for vital area identification

International Nuclear Information System (INIS)

Varnado, G.B.; Ortiz, N.R.

1978-01-01

This paper discusses the use of fault tree analysis to identify those areas of nuclear fuel cycle facilities which must be protected to prevent acts of sabotage that could lead to sifnificant release of radioactive material. By proper manipulation of the fault trees for a plant, an analyst can identify vital areas in a manner consistent with regulatory definitions. This paper discusses the general procedures used in the analysis of any nuclear facility. In addition, a structured, generic approach to the development of the fault trees for nuclear power reactors is presented along with selected results of the application of the generic approach to several plants

Additional borehole geophysical logging at Waste Area Grouping 1 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1994-07-01

This technical memorandum describes the borehole geophysical logging performed at selected coreholes at Waste Area Grouping 1 between March and November 1991 in support of the remedial investigation. The primary objectives of the borehole geophysical logging program were to (1) identify fractured bedrock zones and identify those fractured bedrock zones participating in active groundwater flow, (2) correlate the fractured intervals with the regional stratigraphy described, and (3) further characterize local bedrock geology and hydrogeology and gain insight about the bedrock aquifer flow system. A secondary objective was to provide stratigraphic correlations with existing logs for coreholes CH001 through CH005. Fractured bedrock zones and active or open fractures were identified in all coreholes logged. The fracture identification and analysis process was intended to distinguish between open or active fractures participating in active groundwater flow and closed or inactive fractures that are partially or completely filled (such as with calcite mineralization) and do not support groundwater circulation. Most of the fractures identified are bedding plane. Fracture occurrence varies with the different units of the Chickamauga Group; the greatest density of fractures and active fractures occurs in the upper 150 ft of stratum cored. Fractures actively contributing to groundwater flow were also identified, and direction of fluid movement within fractures was identified for those coreholes with flowmeter data

Wind and wildlife in the Northern Great Plains: identifying low-impact areas for wind development.

Directory of Open Access Journals (Sweden)

Joseph Fargione

Full Text Available Wind energy offers the potential to reduce carbon emissions while increasing energy independence and bolstering economic development. However, wind energy has a larger land footprint per Gigawatt (GW than most other forms of energy production and has known and predicted adverse effects on wildlife. The Northern Great Plains (NGP is home both to some of the world's best wind resources and to remaining temperate grasslands, the most converted and least protected ecological system on the planet. Thus, appropriate siting and mitigation of wind development is particularly important in this region. Steering energy development to disturbed lands with low wildlife value rather than placing new developments within large and intact habitats would reduce impacts to wildlife. Goals for wind energy development in the NGP are roughly 30 GW of nameplate capacity by 2030. Our analyses demonstrate that there are large areas where wind development would likely have few additional impacts on wildlife. We estimate there are ∼1,056 GW of potential wind energy available across the NGP on areas likely to have low-impact for biodiversity, over 35 times development goals. New policies and approaches will be required to guide wind energy development to low-impact areas.

Performance of the Lot Quality Assurance Sampling Method Compared to Surveillance for Identifying Inadequately-performing Areas in Matlab, Bangladesh

OpenAIRE

Bhuiya, Abbas; Hanifi, S.M.A.; Roy, Nikhil; Streatfield, P. Kim

2007-01-01

This paper compared the performance of the lot quality assurance sampling (LQAS) method in identifying inadequately-performing health work-areas with that of using health and demographic surveillance system (HDSS) data and examined the feasibility of applying the method by field-level programme supervisors. The study was carried out in Matlab, the field site of ICDDR,B, where a HDSS has been in place for over 30 years. The LQAS method was applied in 57 work-areas of community health workers i...

CHEAT MOUNTAIN ROADLESS AREA, WEST VIRGINIA.

Science.gov (United States)

Englund, K.J.; Behum, P.T.

1984-01-01

A mineral-resource survey determined that coal is the most important mineral resource in the Cheat Mountain Roadless Area, West Virginia. It is tentatively ranked as high-volatile A to medium-volatile bituminous similar to coal in nearby mining areas, and is primarily of coking quality. Demonstrated coal resources are estimated to total about 11. 6 million short tons in beds more than 28 in. thick in areas of substantiated resource potential and an additional 32. 7 million short tons in beds between 14 and 28 in. thick have been identified. Limestone, shale, clay, and sandstone occur in the area but these commodities are readily available outside the roadless area. Available information suggests little promise for the occurrence of metallic mineral or other energy resources in the area.

Life cycle assessment and additives: state of knowledge

DEFF Research Database (Denmark)

is to identify research needs within this area focusing on both risk assessment (RA) and life cycle assessment (LCA). Besides the sectors on paper and plastics also lubricants, textiles, electronics and leather are included in RiskCycle. On plastics a literature review regarding the state of knowledge......Concerns about possible toxic effects from additives/impurities accumulated in globally recycled waste/resources like paper and plastics was one of the main reasons for starting up the EU FP7 Coordination Action project RiskCycle (www.wadef.com/projects/riskcycle). A key aim of the project...... on additives/impurities in LCA has been performed within RiskCycle. Several inventory databases (LCI data) have been investigated and the result shows that most LCI databases use PlasticsEurope data for plastics production. Most of these data are aggregated and do not include additives. Regarding...

Identifying factors affecting optimal management of agricultural water

Directory of Open Access Journals (Sweden)

Masoud Samian

2015-01-01

In addition to quantitative methodology such as descriptive statistics and factor analysis a qualitative methodology was employed for dynamic simulation among variables through Vensim software. In this study, the factor analysis technique was used through the Kaiser-Meyer-Olkin (KMO and Bartlett tests. From the results, four key elements were identified as factors affecting the optimal management of agricultural water in Hamedan area. These factors were institutional and legal factors, technical and knowledge factors, economic factors and social factors.

USING GIS TO IDENTIFY POTENTIAL AREAS SUSCEPTIBLE TO FLOOD. CASE STUDY: SOLONEŢ RIVER

Directory of Open Access Journals (Sweden)

V. TIPLEA

2011-03-01

Full Text Available Using GIS to Identify Potential Areas Susceptible to Flood. Case Study: Soloneţ River. In this study, we aim to analyze the impact of different peak flows in territory and also a better understanding of the dynamic of a river flow. The methodology used for flood zone delimitation is based on a quantitative analysis model which requires the use of mathematical, physical and statistical operations in order to emphasize the relations between the different variables that were implied (discharges, grain size, terrain morphology, soil saturation, vegetation etc.. The results cannot be expected to be completely accurate but can provide a good representation of the process. Validation of results will inevitably be difficult and should be measured in the field. The information resulting from this study could be useful for raising awareness about both hazards and possible mitigation measure, a key component of disaster risk reduction planning.

Use of the Cumbrian coastal area

International Nuclear Information System (INIS)

1991-12-01

The primary objective of the research was to establish the recreational usage made of the Cumbrian coastal area. Observations of the numbers of adults and children in each area included in the study were undertaken, as well as an interview survey among adults which identified patterns of use by different groups. The interview survey comprised 7070 interviews, 80% of which were with residents of, rather than visitors to, Cumbria. Additional investigations and analyses were conducted to: determine hours of occupancy at coastal areas; observe usage made of particular areas outside the locations and times of the main survey; assess the usage made of coastal areas and inland waterways by members of the public likely to be excluded from the main study (eg. bird watchers, water-sport participants). (author)

Identifying suitable sites for Florida panther reintroduction

Science.gov (United States)

Thatcher, Cindy A.; van Manen, Frank T.; Clark, Joseph D.

2006-01-01

A major objective of the 1995 Florida Panther (Puma concolor cory) Recovery Plan is the establishment of 2 additional panther populations within the historic range. Our goal was to identify prospective sites for Florida panther reintroduction within the historic range based on quantitative landscape assessments. First, we delineated 86 panther home ranges using telemetry data collected from 1981 to 2001 in south Florida to develop a Mahalanobis distance (D2) habitat model, using 4 anthropogenic variables and 3 landscape variables mapped at a 500-m resolution. From that analysis, we identified 9 potential reintroduction sites of sufficient size to support a panther population. We then developed a similar D2 model at a higher spatial resolution to quantify the area of favorable panther habitat at each site. To address potential for the population to expand, we calculated the amount of favorable habitat adjacent to each prospective reintroduction site within a range of dispersal distances of female panthers. We then added those totals to the contiguous patches to estimate the total amount of effective panther habitat at each site. Finally, we developed an expert-assisted model to rank and incorporate potentially important habitat variables that were not appropriate for our empirical analysis (e.g., area of public lands, livestock density). Anthropogenic factors heavily influenced both the landscape and the expert-assisted models. Of the 9 areas we identified, the Okefenokee National Wildlife Refuge, Ozark National Forest, and Felsenthal National Wildlife Refuge regions had the highest combination of effective habitat area and expert opinion scores. Sensitivity analyses indicated that variability among key model parameters did not affect the high ranking of those sites. Those sites should be considered as starting points for the field evaluation of potential reintroduction sites.

Additive Manufacturing and Business Models: Current Knowledge and Missing Perspectives

Directory of Open Access Journals (Sweden)

Christina Öberg

2018-06-01

Full Text Available Additive manufacturing, that is 3D printing technology, may change the way companies operate their businesses. This article adopts a business model perspective to create an understanding of what we know about these changes. It summarizes current knowledge on additive manufacturing within management and business research, and it discusses future research directions in relation to business models for additive manufacturing. Using the scientific database Web of Science, 116 journal articles were identified. The literature review reveals that most research concerns manufacturing optimization. A more holistic view of the changes that additive manufacturing may bring about for firms is needed, as is more research on changed value propositions, and customer/sales-related issues. The article contributes to previous research by systematically summarizing additive manufacturing research in the business and management literature, and by highlighting areas for further investigation related to the business models of individual firms.

Beacon-based tourist information system to identify visiting trends of tourists

Directory of Open Access Journals (Sweden)

Akihiro Yamaguchi

2017-11-01

Full Text Available In this study, we propose a system that provides tourist information and obtains trends of visiting tourists using beacons and cloud service. As part of our research, we are working on the promotion of local area tourism in cooperation with a local community. A low energy Bluetooth device is used as a beacon to transmit a universally unique identifier. In addition, beacons are placed at sightseeing spots and tourist facilities. Our proposed system comprises two application programs; one is a client-side application program that provides area-specific tourist information corresponding to the detected beacon. The other is a server-side application to record time and location information of the detected beacons. In this paper, we describe the scheme of our system, and present the results of experiments conducted using the prototype system in the local tourist area. In addition, we discuss an open platform for information collection services using beacons.

Identifying Potential Areas of Human Zika Infection in the City of Los Angeles, California by Use of Remote Sensing Imagery

Science.gov (United States)

Lee, J.

2017-12-01

As of April 2017, California is the third most prevalent state on the United States for Zika Infection and Southern California has an ever growing population of Aedes mosquitos. Zika is a disease which poses a significant risk to humans and other mammals due to its effects on pregnancy. This emerging disease is highly contagious due to its spread of infection primarily by Aedes aegypti mosquitos. Aedes mosquitos are able to breed in small rain collecting containers which allow the species to persevere in urban and semi urban environments. We hope to identify potential areas with risk of human infection within Los Angeles and its surrounding areas. This study integrates remote sensing, GIS, statistical, and environmental techniques to study favorable habitats for this particular species of mosquitos and their larvae. The study of the geographic and landscape factors which promote the larvae development allow for the disease spread to be analyzed and modeled. There are several goals in the development of this study. These include the coordination of statistical data with local epidemiology departments, identify workflows to improve efficiency, create models which can be utilized for disease prevention, and identify geographic risk factors for the spread of Zika.

Assessing shortfalls and complementary conservation areas for national plant biodiversity in South Korea.

Science.gov (United States)

Choe, Hyeyeong; Thorne, James H; Huber, Patrick R; Lee, Dongkun; Quinn, James F

2018-01-01

Protected areas (PAs) are often considered the most important biodiversity conservation areas in national plans, but PAs often do not represent national-scale biodiversity. We evaluate the current conservation status of plant biodiversity within current existing PAs, and identify potential additional PAs for South Korea. We modeled species ranges for 2,297 plant species using Multivariate Adaptive Regression Splines and compared the level of mean range representation in South Korea's existing PAs, which comprise 5.7% of the country's mainland area, with an equal-area alternative PA strategy selected with the reserve algorithm Marxan. We also used Marxan to model two additional conservation scenarios that add lands to approach the Aichi Biodiversity Target objectives (17% of the country). Existing PAs in South Korea contain an average of 6.3% of each plant species' range, compared to 5.9% in the modeled equal-area alternative. However, existing PAs primarily represent a high percentage of the ranges for high-elevation and small range size species. The additional PAs scenario that adds lands to the existing PAs covers 14,587.55 km2, and would improve overall plant range representation to a mean of 16.8% of every species' range. The other additional PAs scenario, which selects new PAs from all lands and covers 13,197.35 km2, would improve overall plant range representation to a mean of 13.5%. Even though the additional PAs that includes existing PAs represents higher percentages of species' ranges, it is missing many biodiversity hotspots in non-mountainous areas and the additional PAs without locking in the existing PAs represent almost all species' ranges evenly, including low-elevation ones with larger ranges. Some priority conservation areas we identified are expansions of, or near, existing PAs, especially in northeastern and southern South Korea. However, lowland coastal areas and areas surrounding the capital city, Seoul, are also critical for biodiversity

Wide and High Additive Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Post, Brian K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Roschli, Alex C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-03-01

The goal of this project is to develop and demonstrate the enabling technologies for Wide and High Additive Manufacturing (WHAM). WHAM will open up new areas of U.S. manufacturing for very large tooling in support of the transportation and energy industries, significantly reducing cost and lead time. As with Big Area Additive Manufacturing (BAAM), the initial focus is on the deposition of composite materials.

Multiscale, multispectral and multitemporal satellite data to identify archaeological remains in the archaeological area of Tiwanaku (Bolivia)

Science.gov (United States)

Masini, Nicola; Lasaponara, Rosa

2015-04-01

The aim of this paper is to investigate the cultural landscape of the archaeological area of Tiwanaku (Bolivia) using multiscale, multispectral and multitemporal satellite data. Geospatial analysis techniques were applied to the satellite data sets in order to enhance and map traces of past human activities and perform a spatial characterization of environmental and cultural patterns. In particular, in the Tiwanaku area, the approach based on local indicators of spatial autocorrelation (LISA) applied to ASTER data allowed us to identify traces of a possible ancient hydrographic network with a clear spatial relation with the well-known moat surrounding the core of the monumental area. The same approach applied to QuickBird data, allowed us to identify numerous traces of archaeological interest, in Mollo Kontu mound, less investigated than the monumental area. Some of these traces were in perfect accordance with the results of independent studies, other were completely unknown. As a whole, the detected features, composing a geometric pattern with roughly North-South orientation, closely match those of the other residential contexts at Tiwanaku. These new insights, captured from multitemporal ASTER and QuickBird data processing, suggested new questions on the ancient landscape and provided important information for planning future field surveys and archaeogeophyical investigations. Reference [1] Lasaponara R., Masini N. 2014. Beyond modern landscape features: New insights in thearchaeological area of Tiwanaku in Bolivia from satellite data. International Journal of Applied Earth Observation and Geoinformation, 26, 464-471, http://dx.doi.org/10.1016/j.jag.2013.09.00. [2] Tapete D., Cigna F., Masini N., Lasaponara R. 2013. Prospection and monitoring of the archaeological heritage of Nasca, Peru, with ENVISAT ASAR, Archaeological Prospection, 20, 133-147, doi: 10.1002/arp.1449. [3] Lasaponara R, N Masini, 2012 Satellite Remote Sensing, A New Tool for Archaeology (Series

Molecular characterization of an unauthorized genetically modified Bacillus subtilis production strain identified in a vitamin B2 feed additive.

Science.gov (United States)

Paracchini, Valentina; Petrillo, Mauro; Reiting, Ralf; Angers-Loustau, Alexandre; Wahler, Daniela; Stolz, Andrea; Schönig, Birgit; Matthies, Anastasia; Bendiek, Joachim; Meinel, Dominik M; Pecoraro, Sven; Busch, Ulrich; Patak, Alex; Kreysa, Joachim; Grohmann, Lutz

2017-09-01

Many food and feed additives result from fermentation of genetically modified (GM) microorganisms. For vitamin B2 (riboflavin), GM Bacillus subtilis production strains have been developed and are often used. The presence of neither the GM strain nor its recombinant DNA is allowed for fermentation products placed on the EU market as food or feed additive. A vitamin B 2 product (80% feed grade) imported from China was analysed. Viable B. subtilis cells were identified and DNAs of two bacterial isolates (LHL and LGL) were subjected to three whole genome sequencing (WGS) runs with different devices (MiSeq, 454 or HiSeq system). WGS data revealed the integration of a chloramphenicol resistance gene, the deletion of the endogenous riboflavin (rib) operon and presence of four putative plasmids harbouring rib operons. Event- and construct-specific real-time PCR methods for detection of the GM strain and its putative plasmids in food and feed products have been developed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Identifying Emerging Trends of Financial Business Method Patents

Directory of Open Access Journals (Sweden)

Won Sang Lee

2017-09-01

Full Text Available Financial technology has become an important part of the banking industry in recent times. This study attempts to propose a framework to identify emerging areas and trends using financial business method patents. Based on the abstracts of financial business method patents registered at the United States Patent and Trademark Office, this study first applies latent Dirichlet allocation to identify emerging topics. The probability of the annual occurrence of each topic is adjusted through the exponentially weighted moving average to reflect the importance of the recent probability of topics. Each topic is classified as “hot” or “cold” depending on whether the exponentially weighted moving average of the probabilities exceeds the threshold. We applied survival analysis to the time gap of recurrently becoming hot from a cold status with the associated factor of financial business method patents. The findings suggest that the topic with the short granted period and high forward citation is likely to become hot. In addition, the topic that is aged and specific in narrow areas is likely to continuously change into the hot or cold status. The approach proposed in this study contributes toward understanding topic emergence in the financial area and pursuing sustainable development.

Estimating forest biomass and identifying low-intensity logging areas using airborne scanning lidar in Antimary State Forest, Acre State, Western Brazilian Amazon

Science.gov (United States)

Marcus V.N. d' Oliveira; Stephen E. Reutebuch; Robert J. McGaughey; Hans-Erik. Andersen

2012-01-01

The objectives of this study were to estimate above ground forest biomass and identify areas disturbed by selective logging in a 1000 ha Brazilian tropical forest in the Antimary State Forest using airborne lidar data. The study area consisted of three management units, two of which were unlogged, while the third unit was selectively logged at a low intensity. A...

Topological Constraints on Identifying Additive Link Metrics via End-to-end Paths Measurements

Science.gov (United States)

2012-09-20

identifiable if and only ifR in (1) has full column rank, i.e., rank(R) = n. In other words, to uniquely determine w, there must be n linearly...be identified from paths traversing l1; similar argument applies to l2. Moreover, similar analysis as in the proof of this lemma shows that none of

Identifying trace evidence in data wiping application software

Directory of Open Access Journals (Sweden)

Gregory H. Carlton

2012-06-01

Full Text Available One area of particular concern for computer forensics examiners involves situations in which someone utilized software applications to destroy evidence. There are products available in the marketplace that are relatively inexpensive and advertised as being able to destroy targeted portions of data stored within a computer system. This study was undertaken to identify these tools and analyze them to determine the extent to which each of the evaluated data wiping applications perform their tasks and to identify trace evidence, if any, left behind on disk media after executing these applications. We evaluated five Windows 7 compatible software products whose advertised features include the ability for users to wipe targeted files, folders, or evidence of selected activities. We conducted a series of experiments that involved executing each application on systems with identical data, and we then analyzed the results and compared the before and after images for each application. We identified information for each application that is beneficial to forensics examiners when faced with similar situations. This paper describes our application selection process, our application evaluation methodology, and our findings. Following this, we describe limitations of this study and suggest areas of additional research that will benefit the study of digital forensics.

Identifying future electricity-water tradeoffs in the United States

International Nuclear Information System (INIS)

Sovacool, Benjamin K.; Sovacool, Kelly E.

2009-01-01

Researchers for the electricity industry, national laboratories, and state and federal agencies have begun to argue that the country could face water shortages resulting from the addition of thermoelectric power plants, but have not attempted to depict more precisely where or how severe those shortages will be. Using county-level data on rates of population growth collected from the US Census Bureau, utility estimates of future planned capacity additions in the contiguous United States reported to the US Energy Information Administration, and scientific estimates of anticipated water shortages provided from the US Geologic Survey and National Oceanic and Atmospheric Administration, this paper highlights the most likely locations of severe shortages in 22 counties brought about by thermoelectric capacity additions. Within these areas are some 20 major metropolitan regions where millions of people live. After exploring the electricity-water nexus and explaining the study's methodology, the article then focuses on four of these metropolitan areas - Houston, Texas; Atlanta, Georgia; Las Vegas, Nevada; New York, New York - to deepen an understanding of the water and electricity challenges they may soon be facing. It concludes by identifying an assortment of technologies and policies that could respond to these electricity-water tradeoffs.

An Integrated H-G Scheme Identifying Areas for Soil Remediation and Primary Heavy Metal Contributors: A Risk Perspective

OpenAIRE

Bin Zou; Xiaolu Jiang; Xiaoli Duan; Xiuge Zhao; Jing Zhang; Jingwen Tang; Guoqing Sun

2017-01-01

Traditional sampling for soil pollution evaluation is cost intensive and has limited representativeness. Therefore, developing methods that can accurately and rapidly identify at-risk areas and the contributing pollutants is imperative for soil remediation. In this study, we propose an innovative integrated H-G scheme combining human health risk assessment and geographical detector methods that was based on geographical information system technology and validated its feasibility in a renewabl...

Complete Bouguer gravity and aeromagnetic maps of the Rattlesnake Roadless Area, Missoula County, Montana

Science.gov (United States)

Kulik, Dolores M.

1986-01-01

The Rattlesnake Roadless Area was identified by the U.S. Forest Service as a possible addition to the Wilderness System.  This 120 square mile area is north of Missoula, Mont. (see index map); Rattlesnake Creek forms the major drainage to the south.

Basic research on lattice structures focused on the reliance of the cross sectional area and additional coatings

Directory of Open Access Journals (Sweden)

Kessler Julia

2017-01-01

Full Text Available This scientific survey is about periodic lattice structures which are made by Selective Laser Melting (SLM. Selective laser melting is based on Additive Manufacturing. The increased use and increasing demand of lattice structures in different fields of applications forms the necessity of a closer look on complex structures. Lattice structures can be found in different fields of applications for example in lightweight applications, filters and heat exchangers. Because of the expanding of application areas and thus arising requirements, the quality improvement is indispensable. Additive manufacturing and especially the SLM process enable the manufacturing of highly complex shapes and structures. Further it allows the integration of lightweight structures within to be manufactured applications. These high performance structures and applications need specific boundary and process conditions [1-3]. The main aim of this survey is an extraction of important parameters concerning the shape of lattices. A first focus will be on mechanical properties and the therefore necessary tensile tests.

Identifying forest lands in urban areas in the Central Hardwood Region

Science.gov (United States)

Thomas W. Birch; Rachel Riemann Hershey; Philip Kern

1997-01-01

Forests in urban areas are an important component of urban and suburban environments. They provide places for recreation and environmental education, wildlife habitat for species adapted to living near humans, contribute to general human physical and psychological health. Knowing how much and what type of forest exists in urban areas provides critical baseline data for...

An Integrated H-G Scheme Identifying Areas for Soil Remediation and Primary Heavy Metal Contributors: A Risk Perspective.

Science.gov (United States)

Zou, Bin; Jiang, Xiaolu; Duan, Xiaoli; Zhao, Xiuge; Zhang, Jing; Tang, Jingwen; Sun, Guoqing

2017-03-23

Traditional sampling for soil pollution evaluation is cost intensive and has limited representativeness. Therefore, developing methods that can accurately and rapidly identify at-risk areas and the contributing pollutants is imperative for soil remediation. In this study, we propose an innovative integrated H-G scheme combining human health risk assessment and geographical detector methods that was based on geographical information system technology and validated its feasibility in a renewable resource industrial park in mainland China. With a discrete site investigation of cadmium (Cd), arsenic (As), copper (Cu), mercury (Hg) and zinc (Zn) concentrations, the continuous surfaces of carcinogenic risk and non-carcinogenic risk caused by these heavy metals were estimated and mapped. Source apportionment analysis using geographical detector methods further revealed that these risks were primarily attributed to As, according to the power of the determinant and its associated synergic actions with other heavy metals. Concentrations of critical As and Cd, and the associated exposed CRs are closed to the safe thresholds after remediating the risk areas identified by the integrated H-G scheme. Therefore, the integrated H-G scheme provides an effective approach to support decision-making for regional contaminated soil remediation at fine spatial resolution with limited sampling data over a large geographical extent.

Identifying Hot Spots of Critical Forage Supply in Dryland Nomadic Pastoralist Areas: A Case Study for the Afar Region, Ethiopia

NARCIS (Netherlands)

Sonneveld, B.G.J.S.; Keyzer, M.A.; van Wesenbeeck, C.F.A.; Georgis, Kidane; Beyene, Fekadu; Urbano, Ferdinando; Meroni, Michele; Leo, Olivier; Yimer, Merkebu; Abdullatif, Mohammed

2017-01-01

This study develops a methodology to identify hot spots of critical forage supply in nomadic pastoralist areas, using the Afar Region, Ethiopia, as a special case. It addresses two main problems. First, it makes a spatially explicit assessment of fodder supply and demand extracted from a data poor

Analysis of Offshore Wind Energy Leasing Areas for the Rhode Island/Massachusetts Wind Energy Area

Energy Technology Data Exchange (ETDEWEB)

Musial, W.; Elliott, D.; Fields, J.; Parker, Z.; Scott, G.

2013-04-01

The National Renewable Energy Laboratory (NREL), under an interagency agreement with the Bureau of Ocean Energy Management (BOEM), is providing technical assistance to BOEM on the identification and delineation of offshore leasing areas for offshore wind energy development within the Atlantic Coast Wind Energy Areas (WEAs) established by BOEM in 2012. This report focuses on NREL's evaluation of BOEM's Rhode Island/Massachusetts (RIMA) WEA leasing areas. The objective of the NREL evaluation was to assess the proposed delineation of the two leasing areas and determine if the division is reasonable and technically sound. Additionally, the evaluation aimed to identify any deficiencies in the delineation. As part of the review, NREL performed the following tasks: 1. Performed a limited review of relevant literature and RIMA call nominations. 2. Executed a quantitative analysis and comparison of the two proposed leasing areas 3. Conducted interviews with University of Rhode Island (URI) staff involved with the URI Special Area Management Plan (SAMP) 4. Prepared this draft report summarizing the key findings.

Evaluation of Additively Manufactured Metals for Use in Oxygen Systems Project

Science.gov (United States)

Tylka, Jonathan; Cooper, Ken; Peralta, Stephen; Wilcutt, Terrence; Hughitt, Brian; Generazio, Edward

2016-01-01

Space Launch System, Commercial Resupply, and Commercial Crew programs have published intent to use additively manufactured (AM) components in propulsion systems and are likely to include various life support systems in the future. Parts produced by these types of additive manufacturing techniques have not been fully evaluated for use in oxygen systems and the inherent risks have not been fully identified. Some areas of primary concern in the SLS process with respect to oxygen compatibility may be the porosity of the printed parts, fundamental differences in microstructure of an AM part as compared to traditional materials, or increased risk of shed metal particulate into an oxygen system. If an ignition were to occur the printed material could be more flammable than components manufactured from a traditional billet of raw material and/or present a significant hazards if not identified and rigorously studied in advance of implementation into an oxygen system.

Genome-wide association study identifies multiple loci associated with both mammographic density and breast cancer risk

Science.gov (United States)

Lindström, Sara; Thompson, Deborah J.; Paterson, Andrew D.; Li, Jingmei; Gierach, Gretchen L.; Scott, Christopher; Stone, Jennifer; Douglas, Julie A.; dos-Santos-Silva, Isabel; Fernandez-Navarro, Pablo; Verghase, Jajini; Smith, Paula; Brown, Judith; Luben, Robert; Wareham, Nicholas J.; Loos, Ruth J.F.; Heit, John A.; Pankratz, V. Shane; Norman, Aaron; Goode, Ellen L.; Cunningham, Julie M.; deAndrade, Mariza; Vierkant, Robert A.; Czene, Kamila; Fasching, Peter A.; Baglietto, Laura; Southey, Melissa C.; Giles, Graham G.; Shah, Kaanan P.; Chan, Heang-Ping; Helvie, Mark A.; Beck, Andrew H.; Knoblauch, Nicholas W.; Hazra, Aditi; Hunter, David J.; Kraft, Peter; Pollan, Marina; Figueroa, Jonine D.; Couch, Fergus J.; Hopper, John L.; Hall, Per; Easton, Douglas F.; Boyd, Norman F.; Vachon, Celine M.; Tamimi, Rulla M.

2015-01-01

Mammographic density reflects the amount of stromal and epithelial tissues in relation to adipose tissue in the breast and is a strong risk factor for breast cancer. Here we report the results from meta-analysis of genome-wide association studies (GWAS) of three mammographic density phenotypes: dense area, non-dense area and percent density in up to 7,916 women in stage 1 and an additional 10,379 women in stage 2. We identify genome-wide significant (P<5×10−8) loci for dense area (AREG, ESR1, ZNF365, LSP1/TNNT3, IGF1, TMEM184B, SGSM3/MKL1), non-dense area (8p11.23) and percent density (PRDM6, 8p11.23, TMEM184B). Four of these regions are known breast cancer susceptibility loci, and four additional regions were found to be associated with breast cancer (P<0.05) in a large meta-analysis. These results provide further evidence of a shared genetic basis between mammographic density and breast cancer and illustrate the power of studying intermediate quantitative phenotypes to identify putative disease susceptibility loci. PMID:25342443

Additive manufactured serialization

Science.gov (United States)

Bobbitt, III, John T.

2017-04-18

Methods for forming an identifying mark in a structure are described. The method is used in conjunction with an additive manufacturing method and includes the alteration of a process parameter during the manufacturing process. The method can form in a unique identifying mark within or on the surface of a structure that is virtually impossible to be replicated. Methods can provide a high level of confidence that the identifying mark will remain unaltered on the formed structure.

Ring-Shaped Seismicity Structures in the Areas of Sarez and Nurek Water Reservoirs (Tajikistan): Lithosphere Adaptation to Additional Loading

Science.gov (United States)

Kopnichev, Yu. F.; Sokolova, I. N.

2017-12-01

Seismicity characteristics in the areas of Sarez Lake and the Nurek water reservoir are studied. Ring-shaped seismicity structures in two depth ranges (0-33 and 34-70 km) formed prior to the Pamir earthquake of December 7, 2015 ( M w = 7.2). Seismicity rings cross each other near the Usoi Dam, which formed after the strong earthquake in 1911 and led to the formation of Sarez Lake, and near the epicenter of the Pamir earthquake. In addition, three out of the four strongest events ( M ≥ 6.0) recorded in the Pamir region at depths of more than 70 km since 1950 have occurred near Sarez Lake. An aggregate of the data allows us to conclude that the Pamir earthquake, despite its very large energy, refers to events related to induced seismicity. Ring-shaped seismicity structures in two depth ranges also formed in the Nurek water reservoir area. It is supposed that the formation of ring-shaped structures is related to the self-organization processes of a geological system, which result in the ascent of deep-seated fluids. In this respect, the lithosphere is gradually adapting to the additional load related to the filling of the water reservoir. The difference between Nurek Dam (and many other hydroelectric power stations as well) and Usoi Dam is the permanent vibration in the former case due to water falling from a height of more than 200 m. Such an effect can lead to gradual stress dissipation, resulting in the occurrence of much weaker events when compared to the Pamir earthquake of December 7, 2015, in the areas of artificial water reservoirs.

Spatial Accessibility to Health Care Services: Identifying under-Serviced Neighbourhoods in Canadian Urban Areas.

Directory of Open Access Journals (Sweden)

Tayyab Ikram Shah

Full Text Available Urban environments can influence many aspects of health and well-being and access to health care is one of them. Access to primary health care (PHC in urban settings is a pressing research and policy issue in Canada. Most research on access to healthcare is focused on national and provincial levels in Canada; there is a need to advance current understanding to local scales such as neighbourhoods.This study examines spatial accessibility to family physicians using the Three-Step Floating Catchment Area (3SFCA method to identify neighbourhoods with poor geographical access to PHC services and their spatial patterning across 14 Canadian urban settings. An index of spatial access to PHC services, representing an accessibility score (physicians-per-1000 population, was calculated for neighborhoods using a 3km road network distance. Information about primary health care providers (this definition does not include mobile services such as health buses or nurse practitioners or less distributed services such as emergency rooms used in this research was gathered from publicly available and routinely updated sources (i.e. provincial colleges of physicians and surgeons. An integrated geocoding approach was used to establish PHC locations.The results found that the three methods, Simple Ratio, Neighbourhood Simple Ratio, and 3SFCA that produce City level access scores are positively correlated with each other. Comparative analyses were performed both within and across urban settings to examine disparities in distributions of PHC services. It is found that neighbourhoods with poor accessibility scores in the main urban settings across Canada have further disadvantages in relation to population high health care needs.The results of this study show substantial variations in geographical accessibility to PHC services both within and among urban areas. This research enhances our understanding of spatial accessibility to health care services at the neighbourhood

Identifying Distribution of Chlorophyll-a Concentration Using Landsat 8 OLI on Marine Waters Area of Cirebon

Science.gov (United States)

Buditama, Gilang; Damayanti, Astrid; Giok Pin, Tjiong

2017-12-01

Phytoplankton is a microscopic plant that has a function to produces oxygen and organic substances. It also plays a role as a main producer in the food chain of a marine ecosystem. Chlorophyll-a is a colour pigment most common in phytoplankton species, so that the concentration level of chlorophyll-a can be used as an indicator of the abundance of phytoplankton cells, and as a reference for predicting organic potency in the aquatic area. This research discusses about the spatial and temporal distribution of chlorophyll-a and its correlation with salinity and total suspended solid (TSS), in the seawaters of Cirebon, West Java. The goal of this research is to be a source of information for fishermen, and other stakeholders whose related subjects in the field of marine and fisheries to predict fertile water regions and can also be used as an indicator in discovering potential areas to catch pelagic fish in Cirebon seawaters. Chlorophyll-a concentration, salinity, and TSS are identified using remote sensing data such as Landsat-8 OLI multi temporal images according to dry and wet month parameters in the 2014-2015. The results of the processed image are then validated between in-situ measurements in the field and remote sensing imagery at the same time. This research utilizes descriptive analysis, and statistics with spatial approach. The results of the research show that temporally, chlorophyll-a levels have a tendency to be higher in wet months compared to dry months, while chlorophyll-a is higher in areas near the coastline compared to open sea areas. The distribution of chlorophyll-a concentration is affected by salinity and TSS distribution, where salinity has the negative relationship and TSS has the positive relationship with chlorophyll-a distribution.

Fundamental Aspects of Selective Melting Additive Manufacturing Processes

Energy Technology Data Exchange (ETDEWEB)

van Swol, Frank B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Miller, James E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-12-01

Certain details of the additive manufacturing process known as selective laser melting (SLM) affect the performance of the final metal part. To unleash the full potential of SLM it is crucial that the process engineer in the field receives guidance about how to select values for a multitude of process variables employed in the building process. These include, for example, the type of powder (e.g., size distribution, shape, type of alloy), orientation of the build axis, the beam scan rate, the beam power density, the scan pattern and scan rate. The science-based selection of these settings con- stitutes an intrinsically challenging multi-physics problem involving heating and melting a metal alloy, reactive, dynamic wetting followed by re-solidification. In addition, inherent to the process is its considerable variability that stems from the powder packing. Each time a limited number of powder particles are placed, the stacking is intrinsically different from the previous, possessing a different geometry, and having a different set of contact areas with the surrounding particles. As a result, even if all other process parameters (scan rate, etc) are exactly the same, the shape and contact geometry and area of the final melt pool will be unique to that particular configuration. This report identifies the most important issues facing SLM, discusses the fundamental physics associated with it and points out how modeling can support the additive manufacturing efforts.

Identifying future electricity-water tradeoffs in the United States

Energy Technology Data Exchange (ETDEWEB)

Sovacool, Benjamin K. [Energy Governance Program, Centre on Asia and Globalisation, Lee Kuan Yew School of Public Policy, National University of Singapore (Singapore); Sovacool, Kelly E. [Department of Geography, Virginia Polytechnic Institute and State University, Blacksburg, VA (United States)

2009-07-15

Researchers for the electricity industry, national laboratories, and state and federal agencies have begun to argue that the country could face water shortages resulting from the addition of thermoelectric power plants, but have not attempted to depict more precisely where or how severe those shortages will be. Using county-level data on rates of population growth collected from the US Census Bureau, utility estimates of future planned capacity additions in the contiguous United States reported to the US Energy Information Administration, and scientific estimates of anticipated water shortages provided from the US Geologic Survey and National Oceanic and Atmospheric Administration, this paper highlights the most likely locations of severe shortages in 22 counties brought about by thermoelectric capacity additions. Within these areas are some 20 major metropolitan regions where millions of people live. After exploring the electricity-water nexus and explaining the study's methodology, the article then focuses on four of these metropolitan areas - Houston, Texas; Atlanta, Georgia; Las Vegas, Nevada; New York, New York - to deepen an understanding of the water and electricity challenges they may soon be facing. It concludes by identifying an assortment of technologies and policies that could respond to these electricity-water tradeoffs. (author)

Discussion about the use of the volume-specific surface area (VSSA) as criteria to identify nanomaterials according to the EU definition

Energy Technology Data Exchange (ETDEWEB)

Lecloux, André J., E-mail: alecloux@nanocyl.com, E-mail: envicat@skynet.be [ENVICAT Consulting (Belgium)

2015-11-15

In the EU regulation, a material containing particles is considered as nano if, for 50 % or more of the particles in the number size distribution, one or more external dimensions is in the size range 1–100 nm. Due to the difficulty to measure in a reliable way the number particle size distribution, it is suggested to use the volume-specific surface area (VSSA) >60 m{sup 2}/cm{sup 3} as simple screening criterion to identify nanomaterials. This threshold corresponds to monodispersed spherical particles with a size of 100 nm. In this paper, a theoretical study is carried out to identify the effect of the particle shape, polydispersity, agglomeration and aggregation on the VSSA threshold. It appears that the VSSA approach is overprotective because a lot of samples are identified as nanomaterials even if less than 50 % of the particles have a size lower than 100 nm, this 50 % in number criterion being the main identification criterion in the EU definition. Even if the VSSA is leading to many false positive results, it can be used to identify non-nanomaterials as soon as its value is lower than the threshold at the condition to take into account the shape of the particles and their external surface area. This conclusion is true for monomodal distributions of particles but is subject to some restrictions for bimodal distributions.

Discussion about the use of the volume-specific surface area (VSSA) as criteria to identify nanomaterials according to the EU definition

International Nuclear Information System (INIS)

Lecloux, André J.

2015-01-01

In the EU regulation, a material containing particles is considered as nano if, for 50 % or more of the particles in the number size distribution, one or more external dimensions is in the size range 1–100 nm. Due to the difficulty to measure in a reliable way the number particle size distribution, it is suggested to use the volume-specific surface area (VSSA) >60 m 2 /cm 3 as simple screening criterion to identify nanomaterials. This threshold corresponds to monodispersed spherical particles with a size of 100 nm. In this paper, a theoretical study is carried out to identify the effect of the particle shape, polydispersity, agglomeration and aggregation on the VSSA threshold. It appears that the VSSA approach is overprotective because a lot of samples are identified as nanomaterials even if less than 50 % of the particles have a size lower than 100 nm, this 50 % in number criterion being the main identification criterion in the EU definition. Even if the VSSA is leading to many false positive results, it can be used to identify non-nanomaterials as soon as its value is lower than the threshold at the condition to take into account the shape of the particles and their external surface area. This conclusion is true for monomodal distributions of particles but is subject to some restrictions for bimodal distributions

Identifiability in stochastic models

CERN Document Server

1992-01-01

The problem of identifiability is basic to all statistical methods and data analysis, occurring in such diverse areas as Reliability Theory, Survival Analysis, and Econometrics, where stochastic modeling is widely used. Mathematics dealing with identifiability per se is closely related to the so-called branch of ""characterization problems"" in Probability Theory. This book brings together relevant material on identifiability as it occurs in these diverse fields.

The cutoff values of visceral fat area and waist circumference for identifying subjects at risk for metabolic syndrome in elderly Korean: Ansan Geriatric (AGE cohort study

Directory of Open Access Journals (Sweden)

Koh Young

2009-12-01

Full Text Available Abstract Background In Korea, the cutoff values of waist circumference (WC for the identification of metabolic syndrome (MetS were suggested to be 90 cm for men and 85 cm for women based on the analysis mainly in middle-aged adults. As aging is associated with increased fat, especially abdominal visceral fat, the cutoff value of WC may differ according to age. In addition, the usefulness of visceral abdominal fat area (VFA to predict MetS in the elderly has not been studied yet. We aimed to suggest WC and VFA criteria and to compare the predictability of WC and VFA to identify people at risk for MetS. Methods A total of 689 elderly subjects aged ≥63 years (308 men, 381 women were chosen in this cross-sectional study from an ongoing, prospective, population-based study, the Ansan Geriatric (AGE cohort study. VFA was measured by single slice abdominal computed tomography scanning. The metabolic risk factors except WC (plasma glucose, blood pressure, serum triglycerides and HDL cholesterol levels were defined using modified NCEP-ATP III criteria. We estimated the accuracy of VFA and WC for identifying at least two of these factors by receiver operating characteristic (ROC curve analysis. Results Two hundred three of 308 men and 280 of 381 women had ≥2 metabolic risk factors. The area under the ROC curve (AUC value for VFA to predict the presence of ≥2 metabolic risk factors was not significantly different from that for WC (men, 0.735 and 0.750; women, 0.715 and 0.682; AUC values for VFA and WC, respectively. The optimal cutoff points for VFA and WC for predicting the presence of ≥2 metabolic risk factors were 92.6 cm2 and 86.5 cm for men and 88.9 cm2 and 86.5 cm for women. Conclusion WC had comparable power with VFA to identify elderly people who are at risk for MetS. Elderly Korean men and women had very similar cutoff points for both VFA and WC measurements for estimating the risk of MetS. Age-specific cutoff point for WC might be

All Conservation Opportunity Areas (ECO.RES.ALL_OP_AREAS)

Data.gov (United States)

U.S. Environmental Protection Agency — The All_OP_Areas GIS layer are all the Conservation Opportunity Areas identified by MoRAP (produced for EPA Region 7). They designate areas with potential for...

Plutonium focus area. Technology summary

International Nuclear Information System (INIS)

1997-09-01

The Assistant Secretary for the Office of Environmental Management (EM) at the U.S. Department of Energy (DOE) chartered the Plutonium Focus Area (PFA) in October 1995. The PFA open-quotes...provides for peer and technical reviews of research and development in plutonium stabilization activities...close quotes In addition, the PFA identifies and develops relevant research and technology. The purpose of this document is to focus attention on the requirements used to develop research and technology for stabilization, storage, and preparation for disposition of nuclear materials. The PFA Technology Summary presents the approach the PFA uses to identify, recommend, and review research. It lists research requirements, research being conducted, and gaps where research is needed. It also summarizes research performed by the PFA in the traditional research summary format. This document encourages researchers and commercial enterprises to do business with PFA by submitting research proposals or open-quotes white papers.close quotes In addition, it suggests ways to increase the likelihood that PFA will recommend proposed research to the Nuclear Materials Stabilization Task Group (NMSTG) of DOE

Where to Go Next? Identifying Target Areas in the North Atlantic for Future Seafloor Mapping Initiatives

Science.gov (United States)

Woelfl, A. C.; Jencks, J.; Johnston, G.; Varner, J. D.; Devey, C. W.

2017-12-01

Human activities are rapidly expanding into the oceans, yet detailed bathymetric maps do not exist for most of the seafloor that would permit governments to formulate sensible usage rules. Changing this situation will require an enormous international mapping effort. To ensure that this effort is directed towards the regions most in need of mapping, we need to know which areas have already been mapped and which areas are potentially most interesting. Despite various mapping efforts in recent years, large parts of the Atlantic still lack detailed bathymetric information. To successfully plan for future mapping efforts to fill these gaps, knowledge of current data coverage is imperative to avoid duplication of effort. While certain datasets are publically available online (e.g. NOAA's NCEI, EMODnet, IHO-DCDB, LDEO's GMRT), many are not. However, with the limited information we do have at hand, the question remains, where should we map next? And what criteria should we take into account? In 2016, a study was taken on as part of the efforts of the International Atlantic Seabed Mapping Working Group (ASMIWG). The ASMIWG, established by the Tri-Partite Galway Statement Implementation Committee, was tasked to develop a cohesive seabed mapping strategy for the Atlantic Ocean. The aim of our study was to develop a reproducible process for identifying and evaluating potential target areas within the North Atlantic that represent suitable sites for future bathymetric surveys. The sites were selected by applying a GIS-based suitability analysis that included specific user group-based parameters of the marine environment. Furthermore, information regarding current data coverage were gathered to take into account in the selection process. The results reveal the suitability of sites within the North Atlantic based on the selected criteria. Three potential target sites should be seen as flexible suggestions for future mapping initiatives rather than a rigid, defined set of areas

Identifying mismatches between institutional perceptions of water-related risk drivers and water management strategies in three river basin areas

Science.gov (United States)

Räsänen, Aleksi; Juhola, Sirkku; Monge Monge, Adrián; Käkönen, Mira; Kanninen, Markku; Nygren, Anja

2017-07-01

Water-related risks and vulnerabilities are driven by variety of stressors, including climate and land use change, as well as changes in socio-economic positions and political landscapes. Hence, water governance, which addresses risks and vulnerabilities, should target multiple stressors. We analyze the institutional perceptions of the drivers and strategies for managing water-related risks and vulnerabilities in three regionally important river basin areas located in Finland, Mexico, and Laos. Our analysis is based on data gathered through participatory workshops and complemented by qualitative content analysis of relevant policy documents. The identified drivers and proposed risk reduction strategies showed the multidimensionality and context-specificity of water-related risks and vulnerabilities across study areas. Most of the identified drivers were seen to increase risks, but some of the drivers were positive trends, and drivers also included also policy instruments that can both increase or decrease risks. Nevertheless, all perceived drivers were not addressed with suggested risk reduction strategies. In particular, most of the risk reduction strategies were incremental adjustments, although many of the drivers classified as most important were large-scale trends, such as climate change, land use changes and increase in foreign investments. We argue that there is a scale mismatch between the identified drivers and suggested strategies, which questions the opportunity to manage the drivers by single-scale incremental adjustments. Our study suggests that for more sustainable risk and vulnerability reduction, the root causes of water-related risks and vulnerabilities should be addressed through adaptive multi-scale governance that carefully considers the context-specificity and the multidimensionality of the associated drivers and stressors.

Methodology for Identifying and Quantifying Metal Pollutant Sources in Storm Water Runoff

Science.gov (United States)

2015-02-01

sanitary sewer are not viable options. In addition, visual inspections of the drainage areas have been insufficient in identifying and quantifying the...diverting the runoff into the sanitary sewer system, but the cost could exceed millions of dollars. Instead of capturing and treating all stormwater...Unknown Appears only if Building Siding is “metal” Roof Material roof_mat_d Built Up, Metal Panel, Asphalt, Fabric, Clay , Slate, Wood, Other

ISD97, a computer program to analyze data from a series of in situ measurements on a grid and identify potential localized areas of elevated activity

International Nuclear Information System (INIS)

Reginatto, M.; Shebell, P.; Miller, K.M.

1997-10-01

A computer program, ISD97, was developed to analyze data from a series of in situ measurements on a grid and identify potential localized areas of elevated activity. The ISD97 code operates using a two-step process. A deconvolution of the data is carried out using the maximum entropy method, and a map of activity on the ground that fits the data within experimental error is generated. This maximum entropy map is then analyzed to determine the locations and magnitudes of potential areas of elevated activity that are consistent with the data. New deconvolutions are then carried out for each potential area of elevated activity identified by the code. Properties of the algorithm are demonstrated using data from actual field measurements

National assessment of Canadian pandemic preparedness: Employing InFluNet to identify high-risk areas for inter-wave vaccine distribution

Directory of Open Access Journals (Sweden)

Patrick Saunders-Hastings

2017-08-01

Full Text Available Background: Influenza pandemics emerge at irregular and unpredictable intervals to cause substantial health, economic and social burdens. Optimizing health-system response is vital to mitigating the consequences of future pandemics. Methods: We developed a mathematical model to assess the preparedness of Canadian health systems to accommodate pandemic-related increases in patient demand. We identify vulnerable areas, assess the potential of inter-wave vaccination to mitigate impacts and evaluate the association between demographic and health-system characteristics in order to identify predictors of pandemic consequences. Results: Modelled average attack rates were 23.7–37.2% with no intervention and 2.5–6.4% with pre-vaccination. Peak acute-care demand was 7.5–19.5% of capacity with no intervention and 0.6–2.6% with pre-vaccination. The peak ICU demand was 39.3–101.8% with no intervention and 2.9–13.3% with pre-vaccination. Total mortality was 2258–7944 with no intervention and 88–472 with pre-vaccination. Regions of Southern Ontario were identified as most vulnerable to surges in patient demand. The strongest predictors of peak acute-care demand and ICU demand were acute-care bed capacity (R = −0.8697; r2 = 0.7564 and ICU bed capacity (R = −0.8151; r2 = 0.6644, respectively. Demographic characteristics had mild associations with predicted pandemic consequences. Conclusion: Inter-wave vaccination provided adequate acute-care resource protection under all scenarios; ICU resource adequacy was protected under mild disease assumptions, but moderate and severe diseases caused demand to exceed expected availability in 21% and 49% of study areas, respectively. Our study informs priority vaccine distribution strategies for pandemic planning, emphasizing the need for targeted early vaccine distribution to high-risk individuals and areas. Keywords: Pandemic influenza, Vaccination

A simple method to identify areas of environmental risk due to manure application.

Science.gov (United States)

Flores, Héctor; Arumí, José Luis; Rivera, Diego; Lagos, L Octavio

2012-06-01

The management of swine manure is becoming an important environmental issue in Chile. One option for the final disposal of manure is to use it as a biofertilizer, but this practice could impact the surrounding environment. To assess the potential environmental impacts of the use of swine manure as a biofertilizer, we propose a method to identify zones of environmental risk through indices. The method considers two processes: nutrient runoff and solute leaching, and uses available information about soils, crops and management practices (irrigation, fertilization, and rotation). We applied the method to qualitatively assess the environmental risk associated with the use of swine manure as a biofertilizer in an 8,000-pig farm located in Central Chile. Results showed that the farm has a moderate environmental risk, but some specific locations have high environmental risks, especially those associated with impacts on areas surrounding water resources. This information could assist the definition of better farm-level management practices, as well as the preservation of riparian vegetation acting as buffer strips. The main advantage of our approach is that it combines qualitative and quantitative information, including particular situations or field features based on expert knowledge. The method is flexible, simple, and can be easily extended or adapted to other processes.

Resource management plan for the Oak Ridge Reservation. Volume 30, Oak Ridge National Environmental Research Park natural areas and reference areas--Oak Ridge Reservation environmentally sensitive sites containing special plants, animals, and communities

Energy Technology Data Exchange (ETDEWEB)

Pounds, L.R. [Univ. of Tennessee, Knoxville, TN (US); Parr, P.D.; Ryon, M.G. [Oak Ridge National Lab., TN (United States)

1993-08-01

Areas on the Oak Ridge Reservation (ORR) that contain rare plant or animal species or are special habitats are protected through National Environmental Research Park Natural Area (NA) or Reference Area (RA) designations. The US Department of Energy`s Oak Ridge National Environmental Research Park program is responsible for identifying species of vascular plants that are endangered, threatened, or rare and, as much as possible, for conserving those areas in which such species grow. This report includes a listing of Research Park NAs and RAs with general habitat descriptions and a computer-generated map with the areas identified. These are the locations of rare plant or animal species or special habitats that are known at this time. As the Reservation continues to be surveyed, it is expected that additional sites will be designated as Research Park NAs or RAs. This document is a component of a larger effort to identify environmentally sensitive areas on ORR. This report identifies the currently known locations of rare plant species, rare animal species, and special biological communities. Floodplains, wetlands (except those in RAs or NAs), and cultural resources are not included in this report.

Identifying Areas Suitable for the Occurrence of Rift Valley Fever in North Africa: Implications for Surveillance.

Science.gov (United States)

Arsevska, E; Hellal, J; Mejri, S; Hammami, S; Marianneau, P; Calavas, D; Hénaux, V

2016-12-01

Rift Valley fever (RVF) is a vector-borne zoonotic disease that has caused widespread outbreaks throughout Africa and the Arabian Peninsula, with serious consequences for livestock-based economies and public health. Although there have never been any reports of RVF in Morocco, Algeria, Tunisia and Libya, it is a priority disease in the Maghreb, due to the threat of introduction of the virus through transboundary livestock movements or infected mosquito vectors. However, the implementation of surveillance activities and early warning contingency plans requires better knowledge of the epidemiological situation. We conducted a multicriteria decision analysis, integrating host distribution with a combination of important ecological factors that drive mosquito abundance, to identify hotspots and suitable time periods for RVF enzootic circulation (i.e. stable transmission at a low to moderate level for an extended period of time) and an RVF epizootic event (i.e. a sudden occurrence of a large number of infected animals over a large geographic area) in the Maghreb. We also modelled vector species distribution using available information on vector presence and habitat preference. We found that the northern regions of the Maghreb were moderately suitable for RVF enzootics, but highly suitable for RVF epizootics. The vector species distribution model identified these regions as the most favourable mosquito habitats. Due to the low density of animal hosts and arid conditions, the desert region showed low RVF suitability, except in oases. However, the presence of competent vectors in putative unsuitable areas underlines the need for further assessments of mosquito habitat preference. This study produced monthly RVF suitability maps useful for animal health managers and veterinary services involved in designing risk-based surveillance programmes. The suitability maps can be further enhanced using existing country-specific sources of information and by incorporating knowledge

Laser speckle contrast imaging identifies ischemic areas on gastric tube reconstructions following esophagectomy.

Science.gov (United States)

Milstein, Dan M J; Ince, Can; Gisbertz, Suzanne S; Boateng, Kofi B; Geerts, Bart F; Hollmann, Markus W; van Berge Henegouwen, Mark I; Veelo, Denise P

2016-06-01

Gastric tube reconstruction (GTR) is a high-risk surgical procedure with substantial perioperative morbidity. Compromised arterial blood supply and venous congestion are believed to be the main etiologic factors associated with early and late anastomotic complications. Identifying low blood perfusion areas may provide information on the risks of future anastomotic leakage and could be essential for improving surgical techniques. The aim of this study was to generate a method for gastric microvascular perfusion analysis using laser speckle contrast imaging (LSCI) and to test the hypothesis that LSCI is able to identify ischemic regions on GTRs.Patients requiring elective laparoscopy-assisted GTR participated in this single-center observational investigation. A method for intraoperative evaluation of blood perfusion and postoperative analysis was generated and validated for reproducibility. Laser speckle measurements were performed at 3 different time pointes, baseline (devascularized) stomach (T0), after GTR (T1), and GTR at 20° reverse Trendelenburg (T2).Blood perfusion analysis inter-rater reliability was high, with intraclass correlation coefficients for each time point approximating 1 (P < 0.0001). Baseline (T0) and GTR (T1) mean blood perfusion profiles were highest at the base of the stomach and then progressively declined towards significant ischemia at the most cranial point or anastomotic tip (P < 0.01). After GTR, a statistically significant improvement in mean blood perfusion was observed in the cranial gastric regions of interest (P < 0.05). A generalized significant decrease in mean blood perfusion was observed across all GTR regions of interest during 20° reverse Trendelenburg (P < 0.05).It was feasible to implement LSCI intraoperatively to produce blood perfusion assessments on intact and reconstructed whole stomachs. The analytical design presented in this study resulted in good reproducibility of gastric perfusion measurements

Attempt to identify the functional areas of the cerebral cortex on CT slices parallel to the orbito-meatal line

Energy Technology Data Exchange (ETDEWEB)

Tanabe, Hirotaka; Okuda, Junichiro; Nishikawa, Takashi; Nishimura, Tsuyoshi (Osaka Univ. (Japan). Faculty of Medicine); Shiraishi, Junzo

1982-06-01

In order to identify the functional brain areas, such as Broca's area, on computed tomography slices parallel to the orbito-meatal line, the numbers of Brodmann's cortical mapping were shown on a diagram of representative brain sections parallel to the orbito-meatal line. Also, we described a method, using cerebral sulci as anatomical landmarks, for projecting lesions shown by CT scan onto the lateral brain diagram. The procedures were as follows. The distribution of lesions on CT slices was determined by the identification of major cerebral sulci and fissures, such as the Sylvian fissure, the central sulcus, and the superior frontal sulcus. Those lesions were then projected onto the lateral diagram by comparing each CT slice with the horizontal diagrams of brain sections. The method was demonstrated in three cases developing neuropsychological symptoms.

Willingness to Pay Additional Water Rate and Irrigation Knowledge of Farmers in Dinar Karakuyu Irrigation Areas in Turkey

Directory of Open Access Journals (Sweden)

Mevlüt Gül

2017-08-01

Full Text Available Water which has become commodity product which is an important product today. Turkey is not a water rich country. In this study, agricultural enterprises in the field of Irrigation Project in Dinar Karakuyu which was implemented in 1992 by DSI. The study analysed which factors affect the willingness to pay additional irrigation water rate with the help of logit model and the irrigation knowledge of farmers was determined by Likert scale. Dinar Karakuyu irrigation network has begun to lose the function in the region. It was supposed 100% irrigation rate but decreased by approximately 9% today. In this context, DSI (General Directorate of State Hydraulic Works plans to rehabilitation work in the same area. The main material of this study was data obtained from 67 agricultural enterprises through a survey covered by the Irrigation Rehabilitation Project in the province of Afyonkarahisar Karakuyu Dinar. The data was gathered with the help of questionnaires which were answered by farmers in Karakuyu Dinar region. The results indicated that 74.6% of farmers were willingness to pay additional water charge. The data were statistically analysed with the use of the logit model. The model results show that agricultural income, farmers’ educational level, computer ownership, attendance of agricultural training activities, family size and agricultural experience were positive factors affect farmers’ willingness to pay additional water fee.

Identifying the Optimal Offshore Areas for Wave Energy Converter Deployments in Taiwanese Waters Based on 12-Year Model Hindcasts

Directory of Open Access Journals (Sweden)

Hung-Ju Shih

2018-02-01

Full Text Available A 12-year sea-state hindcast for Taiwanese waters, covering the period from 2005 to 2016, was conducted using a fully coupled tide-surge-wave model. The hindcasts of significant wave height and peak period were employed to estimate the wave power resources in the waters surrounding Taiwan. Numerical simulations based on unstructured grids were converted to structured grids with a resolution of 25 × 25 km. The spatial distribution maps of offshore annual mean wave power were created for each year and for the 12-year period. Waters with higher wave power density were observed off the northern, northeastern, southeastern (south of Green Island and southeast of Lanyu and southern coasts of Taiwan. Five energetic sea areas with spatial average annual total wave energy density of 60–90 MWh/m were selected for further analysis. The 25 × 25 km square grids were then downscaled to resolutions of 5 × 5 km, and five 5 × 5 km optimal areas were identified for wave energy converter deployments. The spatial average annual total wave energy yields at the five optimal areas (S1–(S5 were estimated to be 64.3, 84.1, 84.5, 111.0 and 99.3 MWh/m, respectively. The prevailing wave directions for these five areas lie between east and northeast.

Using Latent Semantic Analysis to Identify Research Trends in OpenStreetMap

Directory of Open Access Journals (Sweden)

Sukhjit Singh Sehra

2017-07-01

Full Text Available OpenStreetMap (OSM, based on collaborative mapping, has become a subject of great interest to the academic community, resulting in a considerable body of literature produced by many researchers. In this paper, we use Latent Semantic Analysis (LSA to help identify the emerging research trends in OSM. An extensive corpus of 485 academic abstracts of papers published during the period 2007–2016 was used. Five core research areas and fifty research trends were identified in this study. In addition, potential future research directions have been provided to aid geospatial information scientists, technologists and researchers in undertaking future OSM research.

Additional application areas of the 3D process information display; Weiterfuehrende Einsatzgebiete des 3-D-Prozessinformationsdisplays

Energy Technology Data Exchange (ETDEWEB)

Meissner, K. [Institut fuer Automatisierung und Informatik GmbH, Zentrum fuer industrielle Forschung und Entwicklung, Wernigerode (Germany); Hensel, H. [Hochschule Harz, Fachbereich Automatisierung und Informatik, Wernigerode (Germany)

2007-07-01

The current technological progress in the process industry results in a significant increase of the complexity of control systems. The amount of supervised information grows constantly for each operator because of a higher level of automation and an optimized information acquisition of the control systems. This development results in a cognitive overload of the operator which causes incorrect behaviour and responses in alert situations. In technical literature, several approaches are discussed to counteract this problem. This paper presents the newly developed 3-D Process Information Display (3D-PID) and describes which additional application areas as a primary representation method to the supervision of complex process conditions are imaginable. The 3D-PID is based on a cognitive scenic representation of the process values within a 3-D process room. Particularly the problem of the overview and detail presentation known from the literature is discussed. (orig.)

Additional Research Needs to Support the GENII Biosphere Models

Energy Technology Data Exchange (ETDEWEB)

Napier, Bruce A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Snyder, Sandra F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Arimescu, Carmen [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-11-01

In the course of evaluating the current parameter needs for the GENII Version 2 code (Snyder et al. 2013), areas of possible improvement for both the data and the underlying models have been identified. As the data review was implemented, PNNL staff identified areas where the models can be improved both to accommodate the locally significant pathways identified and also to incorporate newer models. The areas are general data needs for the existing models and improved formulations for the pathway models.

Thoughts on identifiers

CERN Multimedia

CERN. Geneva

2005-01-01

As business processes and information transactions have become an inextricably intertwined with the Web, the importance of assignment, registration, discovery, and maintenance of identifiers has increased. In spite of this, integrated frameworks for managing identifiers have been slow to emerge. Instead, identification systems arise (quite naturally) from immediate business needs without consideration for how they fit into larger information architectures. In addition, many legacy identifier systems further complicate the landscape, making it difficult for content managers to select and deploy identifier systems that meet both the business case and long term information management objectives. This presentation will outline a model for evaluating identifier applications and the functional requirements of the systems necessary to support them. The model is based on a layered analysis of the characteristics of identifier systems, including: * Functional characteristics * Technology * Policy * Business * Social T...

An attempt to identify the functional areas of the cerebral cortex on CT slices parallel to the orbito-meatal line

International Nuclear Information System (INIS)

Tanabe, Hirotaka; Okuda, Junichiro; Nishikawa, Takashi; Nishimura, Tsuyoshi; Shiraishi, Junzo.

1982-01-01

In order to identify the functional brain areas, such as Broca's area, on computed tomography slices parallel to the orbito-meatal line, the numbers of Brodmann's cortical mapping were shown on a diagram of representative brain sections parallel to the orbito-meatal line. Also, we described a method, using cerebral sulci as anatomical landmarks, for projecting lesions shown by CT scan onto the lateral brain diagram. The procedures were as follows. The distribution of lesions on CT slices was determined by the identification of major cerebral sulci and fissures, such as the Sylvian fissure, the central sulcus, and the superior frontal sulcus. Those lesions were then projected onto the lateral diagram by comparing each CT slice with the horizontal diagrams of brain sections. The method was demonstrated in three cases developing neuropsychological symptoms. (author)

Bolder science needed now for protected areas.

Science.gov (United States)

Watson, James E M; Darling, Emily S; Venter, Oscar; Maron, Martine; Walston, Joe; Possingham, Hugh P; Dudley, Nigel; Hockings, Marc; Barnes, Megan; Brooks, Thomas M

2016-04-01

Recognizing that protected areas (PAs) are essential for effective biodiversity conservation action, the Convention on Biological Diversity established ambitious PA targets as part of the 2020 Strategic Plan for Biodiversity. Under the strategic goal to "improve the status of biodiversity by safeguarding ecosystems, species, and genetic diversity," Target 11 aims to put 17% of terrestrial and 10% of marine regions under PA status by 2020. Additionally and crucially, these areas are required to be of particular importance for biodiversity and ecosystem services, effectively and equitably managed, ecologically representative, and well-connected and to include "other effective area-based conservation measures" (OECMs). Whereas the area-based targets are explicit and measurable, the lack of guidance for what constitutes important and representative; effective; and OECMs is affecting how nations are implementing the target. There is a real risk that Target 11 may be achieved in terms of area while failing the overall strategic goal for which it is established because the areas are poorly located, inadequately managed, or based on unjustifiable inclusion of OECMs. We argue that the conservation science community can help establish ecologically sensible PA targets to help prioritize important biodiversity areas and achieve ecological representation; identify clear, comparable performance metrics of ecological effectiveness so progress toward these targets can be assessed; and identify metrics and report on the contribution OECMs make toward the target. By providing ecologically sensible targets and new performance metrics for measuring the effectiveness of both PAs and OECMs, the science community can actively ensure that the achievement of the required area in Target 11 is not simply an end in itself but generates genuine benefits for biodiversity. © 2016 Society for Conservation Biology.

Kinematical simulation of robotic complex operation for implementing full-scale additive technologies of high-end materials, composites, structures, and buildings

Science.gov (United States)

Antsiferov, S. I.; Eltsov, M. Iu; Khakhalev, P. A.

2018-03-01

This paper considers a newly designed electronic digital model of a robotic complex for implementing full-scale additive technologies, funded under a Federal Target Program. The electronic and digital model was used to solve the problem of simulating the movement of a robotic complex using the NX CAD/CAM/CAE system. The virtual mechanism was built and the main assemblies, joints, and drives were identified as part of solving the problem. In addition, the maximum allowed printable area size was identified for the robotic complex, and a simulation of printing a rectangular-shaped article was carried out.

Acquiring additional delayed PET images improves sensitivity and specificity in oncology cases

International Nuclear Information System (INIS)

Lamki, L.M.; Barron, B.J.; Mullani, N.; Joseph, U.; Ehert, E.

2002-01-01

Aim: This study looked into utility of acquiring PET images at 2-3 hours in addition to the standard whole body PET done at 1-hour after FDG injection in certain oncology cases. The objective is to evaluate whether the delayed additional images can decipher equivocal foci of FDG accumulation commonly seen in oncology patients. Typical example is the bowel activity that moves with time. Materials and Methods: PET protocol at our Institution in patients with colon Cancer, Pancreas Ca, Ovarian Ca and Breast Ca include a whole body PET (6-7 bed positions) done at 1-hour after 15 mCi F-18-FDG followed by select limited area PET scan (typically 2 bed stops over the area of interest) at 2-3 hours. Acquisition was undertaken on Siemens ECAT-EXACT Camera - 2-D acquisition and 8 mins. per bed position (5 mins. Emission and 3 mins. Transmission), 16.3 cm FOV and then Iterative Reconstruction. Results: Analysis of the first 115 patients who had additional delayed images resulted in 80% of patients where delayed images helped in interpretation. In 70% of these, delayed images helped in identifying physiological structures, e.g., ureters, bowel, blood vessels and muscles versus pathology. In 25%, they actually helped in identifying malignancy, e.g. more definite FDG accumulation. Almost all helped to boost the confidence of the reader. The contribution was mainly in differentiating bowel and ureter activity from cancer in the abdomen, as these change position with time. In case of pancreas and breast cancer, delayed images contributed in clarifying tumor metabolic activity as well. Inflammation and motion artifacts could also be better defined and so was muscle uptake. Conclusion: (1) Additional delayed PET imaging is very helpful in certain cancers in identifying more lesions and avoiding pitfalls. (2) They can yield higher sensitivity and specificity for colon, ovarian, breast and pancreas cancers. (3) Identification of physiologic structures and differentiation of these from

Identifying, meeting, and assessing customer expectations

International Nuclear Information System (INIS)

Danner, T.A.

1995-01-01

Maintaining proficiency in carrying out mission goals is fundamental to the success of any organization. The definitive mission of the Waste Management and Remedial Action Division (WMRAD) of Oak Ridge National Laboratory (ORNL) is open-quotes to conduct waste management activities in a compliant, publicly acceptable, technically sound, and cost-efficient mannerclose quotes. In order to effectively fulfill this mission, must meet or exceed several standards in respect to our customers. These include: (1) identifying current and future customer expectations; (2) managing our relationships with our customers; (3) ensuring our commitment to our customers; and (4) measuring our success m customer satisfaction. Our customers have a great variety of requirements and expectations. Many of these are in the form of local, state, and federal regulations and environmental standards. Others are brought to our attention through inquires made to the Department of Energy (DOE).Consumer surveys have proven to be effective tools which have been used to make improvements, enhance certain program elements, and identify beneficial areas in already existing programs. In addition, national working groups, technology transfer meetings, and manager/contractor's meeting offer excellent opportunities to assess our activities

Area Recommendation Report for the Crystalline Repository Project: Volume 1, Draft

International Nuclear Information System (INIS)

1986-01-01

This Draft Area Recommendation Report for the Crystalline Repository Project identifies portions of crystalline rock bodies as proposed potentially acceptable sites for consideration in the second high-level radioactive waste repository program. The US Department of Energy evaluated available geologic and environmental data for 235 crystalline rock bodies in the North Central, Northeastern, and Southeastern regions to identify preliminary candidate areas. Further evaluation of these preliminary candidate areas resulted in the selection of 12 as proposed potentially acceptable sites. The 12 proposed potentially acceptable sites are located in the States of Georgia (1), Maine (2), Minnesota (3), New Hampshire (1), North Carolina (2), Virginia (2), and Wisconsin (1). The data, analyses, and rationale with which the 12 proposed potentially acceptable sites were selected are presented in this draft report. The analyses presented demonstrate that the evidence available for each proposed potentially acceptable site supports (1) a finding that the site is not disqualified in accordance with the application requirements of Appendix III of the siting guidelines and (2) a decision to proceed with the continued investigation of the site on the basis of the favorable and potentially adverse conditions identified to date. Once this report is finalized, potentially acceptable sites in crystalline rock will be formally identified by the Secretary of Energy, in accordance with the DOE siting guidelines. These potentially acceptable sites will be investigated and evaluated in more detail during the area phase of the siting process. An additional eight areas, which meet the requirements for identification as potentially acceptable sites, will retain their designation as candidate areas

Usefulness of additional SPECT/CT identifying lymphatico-renal shunt in a patient with chyluria

International Nuclear Information System (INIS)

Suh, Min Seok; Cheon, Gi Jeong; Seo, Hyo Jung; KIm, Hyeon Hoe; Lee, Dong Soo

2015-01-01

Lymphoscintigraphy is known to be a useful and non-invasive modality for the evaluation of lymphatic abnormality. However, lymphoscintigraphy has limitations in evaluating chyluria because of its lack of anatomical information. Additional single-photon emission computed tomography (SPECT) combined with computed tomography (CT) was considered to be potentially helpful in detecting the abnormal lymphatico-renal communication. A 20-year-old male patient was referred to our hospital for evaluation of recurrent chyluria. During the third recurrence of chyluria, additional SPECT/CT along with lymphoscintigraphy was performed for evaluation. From the combined SPECT/CT images, lymphatic drainage of radiotracers to the kidney was well visualized, helping diagnosis of a patient with chyluria

Usefulness of additional SPECT/CT identifying lymphatico-renal shunt in a patient with chyluria

Energy Technology Data Exchange (ETDEWEB)

Suh, Min Seok; Cheon, Gi Jeong; Seo, Hyo Jung; KIm, Hyeon Hoe; Lee, Dong Soo [Seoul National University Hospital, Seoul (Korea, Republic of)

2015-03-15

Lymphoscintigraphy is known to be a useful and non-invasive modality for the evaluation of lymphatic abnormality. However, lymphoscintigraphy has limitations in evaluating chyluria because of its lack of anatomical information. Additional single-photon emission computed tomography (SPECT) combined with computed tomography (CT) was considered to be potentially helpful in detecting the abnormal lymphatico-renal communication. A 20-year-old male patient was referred to our hospital for evaluation of recurrent chyluria. During the third recurrence of chyluria, additional SPECT/CT along with lymphoscintigraphy was performed for evaluation. From the combined SPECT/CT images, lymphatic drainage of radiotracers to the kidney was well visualized, helping diagnosis of a patient with chyluria.

Additional symmetries of supersymmetric KP hierarchies

International Nuclear Information System (INIS)

Stanciu, S.

1993-09-01

We investigate the additional symmetries of several supersymmetric KP hierarchies: The SKP hierarchy of Manin and Radul, the SKP 2 hierarchy, and the Jacobian SKP hierarchy. The main technical tool is the supersymmetric generalisation of a map originally due to Radul between the Lie algebra of superdifferential operators and the Lie algebra of vector fields on the space of supersymmetric Lax operators. In the case of the Manin-Radul SKP hierarchy we identify additional symmetries which form an algebra isomorphic to a subalgebra of superdifferential operators; whereas in the case of the Jacobian SKP, the (additional) symmetries are identified with the algebra itself. (orig.)

Wetland survey of selected areas in the K-24 Site Area of responsibility

Energy Technology Data Exchange (ETDEWEB)

Rosensteel, B.A.; Awl, D.J. [JAYCOR, Environmental Division, Oak Ridge, TN (United States)

1995-07-01

In accordance with DOE Regulations for Compliance with Floodplain/Wetlands Environmental Review Requirements, wetland surveys were conducted in selected areas within the K-25 Area of Responsibility during the summer of 1994. These areas are Mitchell Branch, Poplar Creek, the K-770 OU, Duct Island Peninsula, the Powerhouse area, and the K-25 South Corner. Previously surveyed areas included in this report are the main plant area of the K-25 Site, the K-901 OU, the AVLIS site, and the K-25 South Site. Wetland determinations were based on the USACE methodology. Forty-four separate wetland areas, ranging in size from 0.13 to 4.23 ha, were identified. Wetlands were identified in all of the areas surveyed with the exception of the interior of the Duct Island Peninsula and the main plant area of the K-25 Site. Wetlands perform functions such as floodflow alteration, sediment stabilization, sediment and toxicant retention, nutrient transformation, production export, and support of aquatic species and wildlife diversity and abundance. The forested, scrub-shrub, and emergent wetlands identified in the K-25 area perform some or all of these functions to varying degrees.

Wetland survey of selected areas in the K-24 Site Area of responsibility

International Nuclear Information System (INIS)

Rosensteel, B.A.; Awl, D.J.

1995-07-01

In accordance with DOE Regulations for Compliance with Floodplain/Wetlands Environmental Review Requirements, wetland surveys were conducted in selected areas within the K-25 Area of Responsibility during the summer of 1994. These areas are Mitchell Branch, Poplar Creek, the K-770 OU, Duct Island Peninsula, the Powerhouse area, and the K-25 South Corner. Previously surveyed areas included in this report are the main plant area of the K-25 Site, the K-901 OU, the AVLIS site, and the K-25 South Site. Wetland determinations were based on the USACE methodology. Forty-four separate wetland areas, ranging in size from 0.13 to 4.23 ha, were identified. Wetlands were identified in all of the areas surveyed with the exception of the interior of the Duct Island Peninsula and the main plant area of the K-25 Site. Wetlands perform functions such as floodflow alteration, sediment stabilization, sediment and toxicant retention, nutrient transformation, production export, and support of aquatic species and wildlife diversity and abundance. The forested, scrub-shrub, and emergent wetlands identified in the K-25 area perform some or all of these functions to varying degrees

Additional disulfide bonds in insulin

DEFF Research Database (Denmark)

Vinther, Tine N; Pettersson, Ingrid; Huus, Kasper

2015-01-01

The structure of insulin, a glucose homeostasis-controlling hormone, is highly conserved in all vertebrates and stabilized by three disulfide bonds. Recently, we designed a novel insulin analogue containing a fourth disulfide bond located between positions A10-B4. The N-terminus of insulin's B......-chain is flexible and can adapt multiple conformations. We examined how well disulfide bond predictions algorithms could identify disulfide bonds in this region of insulin. In order to identify stable insulin analogues with additional disulfide bonds, which could be expressed, the Cβ cut-off distance had...... in comparison to analogues with additional disulfide bonds that were more difficult to predict. In contrast, addition of the fourth disulfide bond rendered all analogues resistant to fibrillation under stress conditions and all stable analogues bound to the insulin receptor with picomolar affinities. Thus...

The Support of MPA (Marine Protected Area) in Coral Triangle Area: Evidence from Kei Islands, Indonesia

Science.gov (United States)

Hamid, Syahibul K.; Teniwut, Wellem A.; Teniwut, Roberto M. K.; Rahantoknam, Meyske A.; Hasyim, Cawalinya L.; Hungan, Marselus

2017-10-01

Kei Islands located inside the coral triangle. Therefore, the biodiversity level on the sea in this area is considered high. United nation has proposed for water that included in the coral triangle has to apply marine protected area (MPA) to preserve the area. The main problem is most of the community especially in Kei Islands have depended on the sea as their sources of the economy even fisheries commodity like fish play a large part on the inflation rate and other prosperity indicators likes school and housing. Also, Kei Islands practice on form local wisdom for owning areal of the sea which calls “petuanan laut” by certain of villages or group of villages in one area. This study aimed to map the cluster of catching fisheries area based on the quantity of fish supply on a local market in Kei Islands and measure each cluster on their support and perspective on Marine Protected Area (MPA). We conducted a focus group discussion and collecting additional data by questionnaires with descriptive and quantitative analysis with logistic regression. The implication of this study can provide a clear view of coastal communities view on MPA program also to identify an area that has marine resources, human resources, and equipment to provide government an empirical view on catching fisheries in Kei Islands to issued better policy to develop fishing industry in Kei Islands.

Identifying and evaluating electronic learning resources for use in adult-gerontology nurse practitioner education.

Science.gov (United States)

Thompson, Hilaire J; Belza, Basia; Baker, Margaret; Christianson, Phyllis; Doorenbos, Ardith; Nguyen, Huong

2014-01-01

Enhancing existing curricula to meet newly published adult-gerontology advanced practice registered nurse (APRN) competencies in an efficient manner presents a challenge to nurse educators. Incorporating shared, published electronic learning resources (ELRs) in existing or new courses may be appropriate in order to assist students in achieving competencies. The purposes of this project were to (a) identify relevant available ELR for use in enhancing geriatric APRN education and (b) to evaluate the educational utility of identified ELRs based on established criteria. A multilevel search strategy was used. Two independent team members reviewed identified ELR against established criteria to ensure utility. Only resources meeting all criteria were retained. Resources were found for each of the competency areas and included formats such as podcasts, Web casts, case studies, and teaching videos. In many cases, resources were identified using supplemental strategies and not through traditional search or search of existing geriatric repositories. Resources identified have been useful to advanced practice educators in improving lecture and seminar content in a particular topic area and providing students and preceptors with additional self-learning resources. Addressing sustainability within geriatric APRN education is critical for sharing of best practices among educators and for sustainability of teaching and related resources. © 2014.

Long-term plasticity in identified hippocampal GABAergic interneurons in the CA1 area in vivo.

Science.gov (United States)

Lau, Petrina Yau-Pok; Katona, Linda; Saghy, Peter; Newton, Kathryn; Somogyi, Peter; Lamsa, Karri P

2017-05-01

Long-term plasticity is well documented in synapses between glutamatergic principal cells in the cortex both in vitro and in vivo. Long-term potentiation (LTP) and -depression (LTD) have also been reported in glutamatergic connections to hippocampal GABAergic interneurons expressing parvalbumin (PV+) or nitric oxide synthase (NOS+) in brain slices, but plasticity in these cells has not been tested in vivo. We investigated synaptically-evoked suprathreshold excitation of identified hippocampal neurons in the CA1 area of urethane-anaesthetized rats. Neurons were recorded extracellularly with glass microelectrodes, and labelled with neurobiotin for anatomical analyses. Single-shock electrical stimulation of afferents from the contralateral CA1 elicited postsynaptic action potentials with monosynaptic features showing short delay (9.95 ± 0.41 ms) and small jitter in 13 neurons through the commissural pathway. Theta-burst stimulation (TBS) generated LTP of the synaptically-evoked spike probability in pyramidal cells, and in a bistratified cell and two unidentified fast-spiking interneurons. On the contrary, PV+ basket cells and NOS+ ivy cells exhibited either LTD or LTP. An identified axo-axonic cell failed to show long-term change in its response to stimulation. Discharge of the cells did not explain whether LTP or LTD was generated. For the fast-spiking interneurons, as a group, no correlation was found between plasticity and local field potential oscillations (1-3 or 3-6 Hz components) recorded immediately prior to TBS. The results demonstrate activity-induced long-term plasticity in synaptic excitation of hippocampal PV+ and NOS+ interneurons in vivo. Physiological and pathological activity patterns in vivo may generate similar plasticity in these interneurons.

Estimating Demand for and Supply of Pediatric Preventive Dental Care for Children and Identifying Dental Care Shortage Areas, Georgia, 2015.

Science.gov (United States)

Cao, Shanshan; Gentili, Monica; Griffin, Paul M; Griffin, Susan O; Harati, Pravara; Johnson, Ben; Serban, Nicoleta; Tomar, Scott

Demand for dental care is expected to outpace supply through 2025. The objectives of this study were to determine the extent of pediatric dental care shortages in Georgia and to develop a general method for estimation that can be applied to other states. We estimated supply and demand for pediatric preventive dental care for the 159 counties in Georgia in 2015. We compared pediatric preventive dental care shortage areas (where demand exceeded twice the supply) designated by our methods with dental health professional shortage areas designated by the Health Resources & Services Administration. We estimated caries risk from a multivariate analysis of National Health and Nutrition Examination Survey data and national census data. We estimated county-level demand based on the time needed to perform preventive dental care services and the proportion of time that dentists spend on pediatric preventive dental care services from the Medical Expenditure Panel Survey. Pediatric preventive dental care supply exceeded demand in Georgia in 75 counties: the average annual county-level pediatric preventive dental care demand was 16 866 hours, and the supply was 32 969 hours. We identified 41 counties as pediatric dental care shortage areas, 14 of which had not been designated by the Health Resources & Services Administration. Age- and service-specific information on dental care shortage areas could result in more efficient provider staffing and geographic targeting.

Additive manufacturing: state-of-the-art and application framework

Directory of Open Access Journals (Sweden)

Vinícius Picanço Rodrigues

2017-09-01

Full Text Available Additive manufacturing encompasses a class of production processes with increasing applications in different areas and supply chains. Due to its flexibility for production in small batches and the versatility of materials and geometries, this technology is recognized as being capable of revolutionizing the production processes as well as changing production strategies that are currently employed. However, there are different technologies under the generic label of additive manufacturing, materials and application areas with different requirements. Given the growing importance of additive manufacturing as a production process, and also considering the need to have a better insight into the potential applications for driving research and development efforts, this article presents a proposal of organization for additive manufacturing applications in seven areas. Additionally, the article provides a panorama of the current development stage of this technology, with a review of its major technological variants. The results presented aim to serve as a basis to support driving initiatives in additive manufacturing in companies, development agencies and research institutions.

Study of the stabilization of a loamy soil with addition of cement

OpenAIRE

Jonas Alexandre; Maria da Glória Alves; Thiago Vicente Lima

2010-01-01

The use of soil-cement bricks is considered a cheaper constructive method than the conventional (ceramic block or concrete), because one of the raw materials is abundant (the soil). The objective of the present work was to identify the soil of the “Codin” area, in the municipality of Campos of Goytacazes - RJ. After this identification, it was possible to determine the best line for the production of soil-cement, in the 9,5x 10x5 cm format, with lines containing the addition of 5% and 10% of ...

THE METHOD FOR IDENTIFYING THE MOST VULNERABLE AREAS CAUSED BY EXOGENOUS PROCESSES UNDER ARIDIFICATION/HUMIDIFICATION (BASED ON GIS AND RS

Directory of Open Access Journals (Sweden)

D. A. Chupina

2017-01-01

Full Text Available The paper presents the method of identifying the most vulnerable territories under exogenous processes caused by aridification/humidification. It is based on the assumption that some forms and types of relief increase resistance of terrestrial ecosystems to external influences, while other kinds of relief make them vulnerable. The relationship between landscape and moistening (ground and climatic is of great importance to plains which have groundwater close to the surface. We have used morphometric analysis to divide the territory into hydromorphic and automorphic landscapes. Hydromorphic territories are those that are affected by additional surface moistening and groundwater, while automorphic landscapes are less dependent on groundwater under normal atmospheric moisture. The territory is ranked according to the degree of vulnerability by expert evaluation method. The developed approach is based entirely on using GIS software (ArcGIS 10.2.1 and processing the DEM SRTM. As a result, two models of vulnerability of natural terrestrial ecosystems to exogenic processes on Baraba Plain (Western Siberia have been created for both aridification and humidification cases. The opportunity to estimate the vulnerability is the novel feature for these models of terrestrial ecosystems, in both regional and local scales. The results obtained confirm the existing ideas about the discrete mosaic character of changes in spatial landscape patterns in the area under consideration. For the southern part of Western Siberia where farming is risky the assessment of the potential degree of vulnerability for ecosystems under conditions of increasing climate aridity and extremes is relevant.

Using a partial sum method and GPS tracking data to identify area restricted search by artisanal fishers at moored fish aggregating devices in the Commonwealth of Dominica.

Directory of Open Access Journals (Sweden)

Michael Alvard

Full Text Available Foragers must often travel from a central place to exploit aggregations of prey. These patches can be identified behaviorally when a forager shifts from travel to area restricted search, identified by a decrease in speed and an increase in sinuosity of movement. Faster, more directed movement is associated with travel. Differentiating foraging behavior at patches from travel to patches is important for a variety of research questions and has now been made easier by the advent of small, GPS devices that can track forager movement with high resolution. In the summer and fall of 2012, movement data were collected from GPS devices placed on foraging trips originating in the artisanal fishing village of Desa Ikan (pseudonym, on the east coast of the Caribbean island nation of the Commonwealth Dominica. Moored FADs are human-made structures anchored to the ocean floor with fish attraction material on or near the surface designed to effectively create a resource patch. The ultimate goal of the research is to understand how property rights are emerging after the introduction of fish aggregating device (FAD technology at the site in 1999. This paper reports on research to identify area-restricted search foraging behavior at FAD patches. For 22 foraging trips simultaneous behavioral observations were made to ground-truth the GPS movement data. Using a cumulative sum method, area restricted search was identified as negative deviations from the mean travel speed and the method was able to correctly identify FAD patches in every case.

Identifying the sources of nitrate contamination of groundwater in an agricultural area (Haean basin, Korea) using isotope and microbial community analyses

International Nuclear Information System (INIS)

Kim, Heejung; Kaown, Dugin; Mayer, Bernhard; Lee, Jin-Yong; Hyun, Yunjung; Lee, Kang-Kun

2015-01-01

An integrated study based on hydrogeochemical, microbiological and dual isotopic approaches for nitrate and sulfate was conducted to elucidate sources and biogeochemical reactions governing groundwater contaminants in different seasons and under different land use in a basin of Korea. The land use in the study area is comprised of forests (58.0%), vegetable fields (27.6%), rice paddy fields (11.4%) and others (3.0%). The concentrations of NO 3 –N and SO 4 2− in groundwater in vegetable fields were highest with 4.2–15.2 mg L −1 and 1.6–19.7 mg L −1 respectively, whereas under paddy fields NO 3 –N concentrations ranged from 0 to 10.7 mg L −1 and sulfate concentrations were ~ 15 mg L −1 . Groundwater with high NO 3 –N concentrations of > 10 mg L −1 had δ 15 N–NO 3 − values ranging from 5.2 to 5.9‰ and δ 18 O values of nitrate between 2.7 and 4.6‰ suggesting that the nitrate was mineralized from soil organic matter that was amended by fertilizer additions. Elevated concentrations of SO 4 2− with δ 34 S–SO 4 2− values between 1 and 6‰ in aquifers in vegetable fields indicated that a mixture of sulfate from atmospheric deposition, mineralization of soil organic matter and from synthetic fertilizers is the source of groundwater sulfate. Elevated δ 18 O–NO 3 − and δ 18 O–SO 4 2− values in samples collected from the paddy fields indicated that denitrification and bacterial sulfate reduction are actively occurring removing sulfate and nitrate from the groundwater. This was supported by high occurrences of denitrifying and sulfate reducing bacteria in groundwater of the paddy fields as evidenced by 16S rRNA pyrosequencing analysis. This study shows that dual isotope techniques combined with microbial data can be a powerful tool for identification of sources and microbial processes affecting NO 3 − and SO 4 2− in groundwater in areas with intensive agricultural land use. - Highlights: • Dual isotope analyses identified

Identifying grain-size dependent errors on global forest area estimates and carbon studies

Science.gov (United States)

Daolan Zheng; Linda S. Heath; Mark J. Ducey

2008-01-01

Satellite-derived coarse-resolution data are typically used for conducting global analyses. But the forest areas estimated from coarse-resolution maps (e.g., 1 km) inevitably differ from a corresponding fine-resolution map (such as a 30-m map) that would be closer to ground truth. A better understanding of changes in grain size on area estimation will improve our...

Urban Forest Health: Identifying Issues and Needs within the Northeastern Area

Science.gov (United States)

USDA Forest Service

1998-01-01

Street trees and forested areas in cities, towns and communities are more than amenities. Besides beauty, trees provide many practical benefits such as shade from summer sun, protection from winter wind, habitat for wildlife, reduced water, air and noise pollution, increased property values, and revitalized tourism and local business trade. But perhaps the greatest...

Key Biodiversity Areas in the Indo-Burma Hotspot: Process, Progress and Future Directions

Directory of Open Access Journals (Sweden)

A.W. Tordoff

2012-08-01

Full Text Available Key Biodiversity Areas (KBAs provide geographic targets for the expansion of protected area coverage, and identify sites for urgent conservation action. Identification of KBAs in the Indo-Burma Hotspot was undertaken during 2003, for a region of analysis comprising Cambodia, Lao PDR, Myanmar (Burma, Thailand and Vietnam, plus parts of southern China. The starting point was information on 282 Important Bird Areas identified by BirdLife International and collaborators. These data were then overlaid with point locality data on globally threatened mammals, reptiles, amphibians, freshwater fish and plants, with additional KBAs identified as required. Through this process, a total of 438 KBAs were identified, covering 258,085km2 or 11.5 percent of the region of analysis. Only 58 percent of the KBAs are wholly or partly included within protected areas, suggesting that there may be a need for further expansion of protected area networks, particularly in Myanmar and Vietnam. The criteria for KBA identification are triggered by 812 species, of which 23 are believed only to occur at a single KBA globally. The KBAs have proven to be a useful conservation priority setting tool in Indo-Burma, helping to guide investments by various donors and application of environmental safeguard policies by international financial institutions. There are fewer examples of KBAs being used to guide expansion of protected area systems in Indo-Burma. In large part, this is because the period of rapid expansion of protected areas in most hotspot countries predated the KBA identification process, and political support for further significant expansion is currently limited.

Selection of material balance areas and item control areas

International Nuclear Information System (INIS)

1975-04-01

Section 70.58, ''Fundamental Nuclear Material Controls,'' of 10 CFR Part 70, ''Special Nuclear Material,'' requires certain licensees authorized to possess more than one effective kilogram of special nuclear material to establish Material Balance Areas (MBAs) or Item Control Areas (ICAs) for the physical and administrative control of nuclear materials. This section requires that: (1) each MBA be an identifiable physical area such that the quantity of nuclear material being moved into or out of the MBA is represented by a measured value; (2) the number of MBAs be sufficient to localize nuclear material losses or thefts and identify the mechanisms; (3) the custody of all nuclear material within an MBA or ICA be the responsibility of a single designated individual; and (4) ICAs be established according to the same criteria as MBAs except that control into and out of such areas would be by item identity and count for previously determined special nuclear material quantities, the validity of which must be ensured by tamper-safing unless the items are sealed sources. This guide describes bases acceptable to the NRC staff for the selection of material balance areas and item control areas. (U.S.)

[Effect of biochar addition on soil evaporation.

Science.gov (United States)

Xu, Jian; Niu, Wen Quan; Zhang, Ming Zhi; Li, Yuan; Lyu, Wang; Li, Kang-Yong; Zou, Xiao-Yang; Liang, Bo-Hui

2016-11-18

In order to determine the rational amount of biochar application and its effect on soil hydrological processes in arid area, soil column experiments were conducted in the laboratory using three biochar additions (5%, 10% and 15%) and four different biochar types (devaporation. The results showed that the addition of biochar could change the phreatic water recharge, soil water-holding capacity, capillary water upward movement and soil evaporation obviously. But the effects were different depending on the type of biochar raw material and the size of particle. The phreatic water recharge increased with the increasing amount of biochar addition. The addition of biochar could obviously enlarge the soil water-holding capacity and promote the capillary water upward movement rate. This effect was greater when using the material of bamboo charcoal compared with using wood charcoal, while biochar with small particle size had greater impact than that with big particle size. The biochar could effectively restrain the soil evaporation at a low addition amount (5%). But it definitely promoted the soil evaporation if the addition amount was very high. In arid area, biochar addition in appropriate amount could improve soil water retention capacity.

Using geographic distribution of well-screen depths and hydrogeologic conditions to identify areas of concern for contaminant migration through inactive supply wells

Science.gov (United States)

Gailey, Robert M.

2018-02-01

Contaminant migration through inactive supply wells can negatively affect groundwater quality and the combined effects from groups of such wells may cause greater impacts. Because the number of wells in many basins is often large and the geographic areas involved can be vast, approaches are needed to estimate potential impacts and focus limited resources for investigation and corrective measures on the most important areas. One possibility is to evaluate the geographic distribution of well-screen depths relative to hydrogeologic conditions and assess where contaminant migration through wells may be impacting groundwater quality. This approach is demonstrated for a geographically extensive area in the southern Central Valley of California, USA. The conditions that lead to wells acting as conduits for contaminant migration are evaluated and areas where the problem likely occurs are identified. Although only a small fraction of all wells appear to act as conduits, potential impacts may be significant considering needs to control nonpoint-source pollution and improve drinking water quality for rural residents. Addressing a limited number of areas where contaminant migration rates are expected to be high may cost-effectively accomplish the most beneficial groundwater quality protection and improvement. While this work focuses on a specific region, the results indicate that impacts from groups of wells may occur in other areas with similar conditions. Analyses similar to that demonstrated here may guide efficient investigation and corrective action in such areas with benefits occurring for groundwater quality. Potential benefits may justify expenditures to develop the necessary data for performing the analyses.

Geophysical surveys combined with laboratory soil column experiments to identify and explore risk areas for soil and water pollution in feedlots

Science.gov (United States)

Espejo-Pérez, Antonio Jesus; Sainato, Claudia Mabel; Jairo Márquez-Molina, John; Giráldez, Juan Vicente; Vanderlinden, Karl

2014-05-01

Changes of land use without a correct planning may produce its deterioration with their social, economical and environmental irreversible consequences over short to medium time range. In Argentina, the expansion of soybean fields induced a reduction of the area of pastures dedicated to stockbreeding. As cattle activity is being progressively concentrated on small pens, at feedlots farms, problems of soil and water pollution, mainly by nitrate, have been detected. The characterization of the spatial and temporal variability of soil water content is very important because the mostly advective transport of solutes. To avoid intensive soil samplings, very expensive, one has to recur to geophysical exploration methods. The objective of this work was to identify risk areas within a feedlot of the NW zone of Buenos Aires Province, in Argentina through geophysical methods. The surveys were carried out with an electromagnetic induction profiler EMI-400 (GSSI) and a Time domain Reflectometry (TDR) survey of depth 0-0.10 m with soil sampling and measurement of moisture content with gravimetric method (0-1.0 m). Several trenches were dug inside the pens and also at a test site, where texture, apparent density, saturated hydraulic conductivity (Ks), electrical conductivity of the saturation paste extract and organic matter content (OM) were measured. The water retention curves for these soils were also determined. At one of the pens undisturbed soil columns were extracted at 3 locations. Laboratory analysis for 0-1.0 m indicated that soil texture was classified as sandy loam, average organic matter content (OM) was greater than 2.3% with low values of apparent density in the first 10 cm. The range of spatial dependence of data suggested that the number of soil samples could be reduced. Soil apparent electrical conductivity (ECa) and soil moisture were well correlated and indicated a clear spatial pattern in the corrals. TDR performance was acceptable to identify the spatial

Artificial intelligence in neurodegenerative disease research: use of IBM Watson to identify additional RNA-binding proteins altered in amyotrophic lateral sclerosis.

Science.gov (United States)

Bakkar, Nadine; Kovalik, Tina; Lorenzini, Ileana; Spangler, Scott; Lacoste, Alix; Sponaugle, Kyle; Ferrante, Philip; Argentinis, Elenee; Sattler, Rita; Bowser, Robert

2018-02-01

Amyotrophic lateral sclerosis (ALS) is a devastating neurodegenerative disease with no effective treatments. Numerous RNA-binding proteins (RBPs) have been shown to be altered in ALS, with mutations in 11 RBPs causing familial forms of the disease, and 6 more RBPs showing abnormal expression/distribution in ALS albeit without any known mutations. RBP dysregulation is widely accepted as a contributing factor in ALS pathobiology. There are at least 1542 RBPs in the human genome; therefore, other unidentified RBPs may also be linked to the pathogenesis of ALS. We used IBM Watson ® to sieve through all RBPs in the genome and identify new RBPs linked to ALS (ALS-RBPs). IBM Watson extracted features from published literature to create semantic similarities and identify new connections between entities of interest. IBM Watson analyzed all published abstracts of previously known ALS-RBPs, and applied that text-based knowledge to all RBPs in the genome, ranking them by semantic similarity to the known set. We then validated the Watson top-ten-ranked RBPs at the protein and RNA levels in tissues from ALS and non-neurological disease controls, as well as in patient-derived induced pluripotent stem cells. 5 RBPs previously unlinked to ALS, hnRNPU, Syncrip, RBMS3, Caprin-1 and NUPL2, showed significant alterations in ALS compared to controls. Overall, we successfully used IBM Watson to help identify additional RBPs altered in ALS, highlighting the use of artificial intelligence tools to accelerate scientific discovery in ALS and possibly other complex neurological disorders.

Rivers and flooded areas identified by medium-resolution remote sensing improve risk prediction of the highly pathogenic avian influenza H5N1 in Thailand

Directory of Open Access Journals (Sweden)

Weerapong Thanapongtharm

2013-11-01

Full Text Available Thailand experienced several epidemic waves of the highly pathogenic avian influenza (HPAI H5N1 between 2004 and 2005. This study investigated the role of water in the landscape, which has not been previously assessed because of a lack of high-resolution information on the distribution of flooded land at the time of the epidemic. Nine Landsat 7- Enhanced Thematic Mapper Plus scenes covering 174,610 km2 were processed using k-means unsupervised classification to map the distribution of flooded areas as well as permanent lakes and reservoirs at the time of the main epidemic HPAI H5N1 wave of October 2004. These variables, together with other factors previously identified as significantly associated with risk, were entered into an autologistic regression model in order to quantify the gain in risk explanation over previously published models. We found that, in addition to other factors previously identified as associated with risk, the proportion of land covered by flooding along with expansion of rivers and streams, derived from an existing, sub-district level (administrative level no. 3 geographical information system database, was a highly significant risk factor in this 2004 HPAI epidemic. These results suggest that water-borne transmission could have partly contributed to the spread of HPAI H5N1 during the epidemic. Future work stemming from these results should involve studies where the actual distribution of small canals, rivers, ponds, rice paddy fields and farms are mapped and tested against farm-level data with respect to HPAI H5N1.

Assessment of Offshore Wind Energy Leasing Areas for the BOEM Massachusetts Wind Energy Area

Energy Technology Data Exchange (ETDEWEB)

Musial, W. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Parker, Z. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Fields, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Scott, G. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Elliott, D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Draxl, C. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-12-01

The U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL), under an interagency agreement with the Bureau of Ocean Energy Management (BOEM), is providing technical assistance to identify and delineate leasing areas for offshore wind energy development within the Atlantic Coast Wind Energy Areas (WEAs) established by BOEM. This report focuses on NREL's development of three delineated leasing area options for the Massachusetts (MA) WEA and the technical evaluation of these leasing areas. The overarching objective of this study is to develop a logical process by which the MA WEA can be subdivided into non-overlapping leasing areas for BOEM's use in developing an auction process in a renewable energy lease sale. NREL worked with BOEM to identify an appropriate number of leasing areas and proposed three delineation alternatives within the MA WEA based on the boundaries announced in May 2012. A primary output of the interagency agreement is this report, which documents the methodology, including key variables and assumptions, by which the leasing areas were identified and delineated.

Additive manufacturing: state-of-the-art and application framework

DEFF Research Database (Denmark)

Rodrigues, Vinicius Picanco; de Senzi Zancul, Eduardo; Gonçalves Mançanares, Cauê

2017-01-01

Additive manufacturing encompasses a class of production processes with increasing applications indifferent areas and supply chains. Due to its flexibility for production in small batches and the versatilityof materials and geometries, this technology is recognized as being capable...... of revolutionizing theproduction processes as well as changing production strategies that are currently employed. However,there are different technologies under the generic label of additive manufacturing, materials and applicationareas with different requirements. Given the growing importance of additive...... manufacturingas a production process, and also considering the need to have a better insight into the potential applicationsfor driving research and development efforts, this article presents a proposal of organizationfor additive manufacturing applications in seven areas. Additionally, the article provides...

First additional language teaching in the foundation phase of schools in disadvantaged areas

OpenAIRE

Ellen Lenyai

2011-01-01

Second language learning in South African schools is of supreme importance given the multilingual nature of the country. However, there is no certainty that teachers in the foundation phase of schools in poor environments have the skills to teach literacy in the first additional language and produce competent learners. This investigation revealed that the methods that teachers used to teach English, as the first additional language did not develop children’s comprehension and communication sk...

Study of the stabilization of a loamy soil with addition of cement

Directory of Open Access Journals (Sweden)

Jonas Alexandre

2010-05-01

Full Text Available The use of soil-cement bricks is considered a cheaper constructive method than the conventional (ceramic block or concrete, because one of the raw materials is abundant (the soil. The objective of the present work was to identify the soil of the “Codin” area, in the municipality of Campos of Goytacazes - RJ. After this identification, it was possible to determine the best line for the production of soil-cement, in the 9,5x 10x5 cm format, with lines containing the addition of 5% and 10% of cement in volume.

The hierarchy-by-interval approach to identifying important models that need improvement in severe-accident simulation codes

International Nuclear Information System (INIS)

Heames, T.J.; Khatib-Rahbar, M.; Kelly, J.E.

1995-01-01

The hierarchy-by-interval (HBI) methodology was developed to determine an appropriate phenomena identification and ranking table for an independent peer review of severe-accident computer codes. The methodology is described, and the results of a specific code review are presented. Use of this systematic and structured approach ensures that important code models that need improvement are identified and prioritized, which allows code sponsors to more effectively direct limited resources in future code development. In addition, critical phenomenological areas that need more fundamental work, such as experimentation, are identified

Corrective action investigation plan for Central Nevada Test Area, CAU No. 417

International Nuclear Information System (INIS)

1997-04-01

This Corrective Action Investigation Plan (CAIP) is part of a US Department of Energy (DOE)-funded environmental investigation of the Central Nevada Test Area (CNTA). This CAIP addresses the surface investigation and characterization of 15 identified Corrective Action Sites (CASs). In addition, several other areas of the CNTA project area have surface expressions that may warrant investigation. These suspect areas will be characterized, if necessary, in subsequent CAIPs or addendums to this CAIP prepared to address these sites. This CAIP addresses only the 15 identified CASs as shown in Table 2-1 that are associated with the drilling and construction of a number of testing wells designed as part of an underground nuclear testing program. The purpose of the wells at the time of construction was to provide subsurface access for the emplacement, testing, and post detonation evaluations of underground nuclear devices. If contamination is found at any of the 15-surface CASs, the extent of contamination will be determined in order to develop an appropriate corrective action

Biocompatibility of photopolymers for additive manufacturing

OpenAIRE

Leonhardt Stefan; Klare Martin; Scheer Maurice; Fischer Theresa; Cordes Burghard; Eblenkamp Markus

2016-01-01

To establish photopolymers for the production of class II or class III medical products by additive manufacturing it is essential to know which components of photopolymeric systems, consisting of monomers, photoinitiators and additives, are the determining factors on their biocompatible properties. In this study the leachable substances of a cured photopolymeric system were eluted and identified by HPLC-MS detection. In addition the cured photopolymer was testes for cytotoxicity and genotoxic...

Using the Theory of Planned Behavior to identify key beliefs underlying chlamydia testing intentions in a sample of young people living in deprived areas.

Science.gov (United States)

Booth, Amy R; Norman, Paul; Harris, Peter R; Goyder, Elizabeth

2015-09-01

The Theory of Planned Behavior was used to identify the key behavioural, normative and control beliefs underlying intentions to test regularly for chlamydia among young people living in socially and economically deprived areas - a high-risk group for infection. Participants (N = 278, 53% male; mean age 17 years) were recruited from a vocational college situated in an area in the most deprived national quintile (England). Participants completed measures of behavioural, normative and control beliefs, plus intention to test regularly for chlamydia. The behavioural, normative and control beliefs most strongly correlated with intentions to test regularly for chlamydia were beliefs about stopping the spread of infection, partners' behaviour and the availability of testing. These beliefs represent potential targets for interventions to increase chlamydia testing among young people living in deprived areas. © The Author(s) 2013.

Remedial investigation concept plan for the groundwater operable units at the chemical plant area and the ordnance works area, Weldon Spring, Missouri

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-15

The U.S. Department of Energy (DOE) and the U.S. Department of the Army (DA) are conducting cleanup activities at two properties--the DOE chemical plant area and the DA ordnance works area (the latter includes the training area)--located in the Weldon Spring area in St. Charles County, Missouri. These areas are on the National Priorities List (NPL), and cleanup activities at both areas are conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. DOE and DA are conducting a joint remedial investigation (RI) and baseline risk assessment (BRA) as part of the remedial investigation/feasibility study (RI/FS) for the groundwater operable units for the two areas. This joint effort will optimize further data collection and interpretation efforts and facilitate overall remedial decision making since the aquifer of concern is common to both areas. A Work Plan issued jointly in 1995 by DOE and the DA discusses the results of investigations completed at the time of preparation of the report. The investigations were necessary to provide an understanding of the groundwater system beneath the chemical plant area and the ordnance works area. The Work Plan also identifies additional data requirements for verification of the evaluation presented.

Remedial investigation concept plan for the groundwater operable units at the chemical plant area and the ordnance works area, Weldon Spring, Missouri

International Nuclear Information System (INIS)

1999-01-01

The U.S. Department of Energy (DOE) and the U.S. Department of the Army (DA) are conducting cleanup activities at two properties--the DOE chemical plant area and the DA ordnance works area (the latter includes the training area)--located in the Weldon Spring area in St. Charles County, Missouri. These areas are on the National Priorities List (NPL), and cleanup activities at both areas are conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. DOE and DA are conducting a joint remedial investigation (RI) and baseline risk assessment (BRA) as part of the remedial investigation/feasibility study (RI/FS) for the groundwater operable units for the two areas. This joint effort will optimize further data collection and interpretation efforts and facilitate overall remedial decision making since the aquifer of concern is common to both areas. A Work Plan issued jointly in 1995 by DOE and the DA discusses the results of investigations completed at the time of preparation of the report. The investigations were necessary to provide an understanding of the groundwater system beneath the chemical plant area and the ordnance works area. The Work Plan also identifies additional data requirements for verification of the evaluation presented

Additive-manufactured patient-specific titanium templates for thoracic pedicle screw placement: novel design with reduced contact area.

Science.gov (United States)

Takemoto, Mitsuru; Fujibayashi, Shunsuke; Ota, Eigo; Otsuki, Bungo; Kimura, Hiroaki; Sakamoto, Takeshi; Kawai, Toshiyuki; Futami, Tohru; Sasaki, Kiyoyuki; Matsushita, Tomiharu; Nakamura, Takashi; Neo, Masashi; Matsuda, Shuich

2016-06-01

Image-based navigational patient-specific templates (PSTs) for pedicle screw (PS) placement have been described. With recent advances in three-dimensional computer-aided designs and additive manufacturing technology, various PST designs have been reported, although the template designs were not optimized. We have developed a novel PST design that reduces the contact area without sacrificing stability. It avoids susceptibility to intervening soft tissue, template geometric inaccuracy, and difficulty during template fitting. Fourteen candidate locations on the posterior aspect of the vertebra were evaluated. Among them, locations that had high reproducibility on computed tomography (CT) images and facilitated accurate PS placement were selected for the final PST design. An additive manufacturing machine (EOSINT M270) fabricated the PSTs using commercially pure titanium powder. For the clinical study, 36 scoliosis patients and 4 patients with ossification of the posterior longitudinal ligament (OPLL) were treated with thoracic PSs using our newly developed PSTs. We intraoperatively and postoperatively evaluated the accuracy of the PS hole created by the PST. Based on the segmentation reproducibility and stability analyses, we selected seven small, round contact points for our PST: bilateral superior and inferior points on the transverse process base, bilateral inferior points on the laminar, and a superior point on the spinous process. Clinically, the success rates of PS placement using this PST design were 98.6 % (414/420) for scoliosis patients and 100 % (46/46) for OPLL patients. This study provides a useful design concept for the development and introduction of patient-specific navigational templates for placing PSs.

Fine-mapping identifies two additional breast cancer susceptibility loci at 9q31.2

DEFF Research Database (Denmark)

Orr, Nick; Dudbridge, Frank; Dryden, Nicola

2015-01-01

We recently identified a novel susceptibility variant, rs865686, for estrogen-receptor positive breast cancer at 9q31.2. Here, we report a fine-mapping analysis of the 9q31.2 susceptibility locus using 43 160 cases and 42 600 controls of European ancestry ascertained from 52 studies and a further...

Fine-mapping identifies two additional breast cancer susceptibility loci at 9q31.2

NARCIS (Netherlands)

N. Orr (Nick); F. Dudbridge (Frank); N. Dryden (Nicola); S. Maguire (Sarah); D. Novo (Daniela); E. Perrakis (Eleni); N. Johnson (Nichola); M. Ghoussaini (Maya); J. Hopper (John); M.C. Southey (Melissa); C. Apicella (Carmel); J. Stone (Jennifer); M.K. Schmidt (Marjanka); A. Broeks (Annegien); L.J. van 't Veer (Laura); F.B.L. Hogervorst (Frans); P.A. Fasching (Peter); L. Haeberle (Lothar); A.B. Ekici (Arif); M.W. Beckmann (Matthias); L.J. Gibson (Lorna); A. Aitken; H. Warren (Helen); E.J. Sawyer (Elinor); I.P. Tomlinson (Ian); M. Kerin (Michael); N. Miller (Nicola); B. Burwinkel (Barbara); F. Marme (Federick); A. Schneeweiss (Andreas); C. Sohn (Chistof); P. Guénel (Pascal); T. Truong (Thérèse); E. Cordina-Duverger (Emilie); M. Sanchez (Marie); S.E. Bojesen (Stig); B.G. Nordestgaard (Børge); S.F. Nielsen (Sune); H. Flyger (Henrik); J. Benítez (Javier); M.P. Zamora (Pilar); J.I.A. Perez (Jose Ignacio Arias); P. Menéndez (Primitiva); H. Anton-Culver (Hoda); S.L. Neuhausen (Susan); H. Brenner (Hermann); A.K. Dieffenbach (Aida Karina); V. Arndt (Volker); C. Stegmaier (Christa); U. Hamann (Ute); H. Brauch (Hiltrud); C. Justenhoven (Christina); T. Brüning (Thomas); Y.-D. Ko (Yon-Dschun); H. Nevanlinna (Heli); K. Aittomäki (Kristiina); C. Blomqvist (Carl); S. Khan (Sofia); N.V. Bogdanova (Natalia); T. Dörk (Thilo); A. Lindblom (Annika); S. Margolin (Sara); A. Mannermaa (Arto); V. Kataja (Vesa); V-M. Kosma (Veli-Matti); J.M. Hartikainen (J.); G. Chenevix-Trench (Georgia); J. Beesley (Jonathan); D. Lambrechts (Diether); M. Moisse (Matthieu); O.A.M. Floris; B. Beuselinck (B.); J. Chang-Claude (Jenny); A. Rudolph (Anja); P. Seibold (Petra); D. Flesch-Janys (Dieter); P. Radice (Paolo); P. Peterlongo (Paolo); B. Peissel (Bernard); V. Pensotti (Valeria); F.J. Couch (Fergus); J.E. Olson (Janet); S. Slettedahl (Seth); C. Vachon (Celine); G.G. Giles (Graham G.); R.L. Milne (Roger L.); C.A. McLean (Catriona Ann); C.A. Haiman (Christopher); B.E. Henderson (Brian); F.R. Schumacher (Fredrick); L. Le Marchand (Loic); J. Simard (Jacques); M.S. Goldberg (Mark); F. Labrèche (France); M. Dumont (Martine); V. Kristensen (Vessela); G.G. Alnæs (Grethe); S. Nord (Silje); A.-L. Borresen-Dale (Anne-Lise); W. Zheng (Wei); S.L. Deming-Halverson (Sandra); M. Shrubsole (Martha); J. Long (Jirong); R. Winqvist (Robert); K. Pykäs (Katri); A. Jukkola-Vuorinen (Arja); M. Grip (Mervi); I.L. Andrulis (Irene); J.A. Knight (Julia); G. Glendon (Gord); S. Tchatchou (Sandrine); P. Devilee (Peter); R.A.E.M. Tollenaar (Robertus A. E. M.); C.M. Seynaeve (Caroline); C.J. van Asperen (Christi); M. García-Closas (Montserrat); J.D. Figueroa (Jonine); S.J. Chanock (Stephen); J. Lissowska (Jolanta); K. Czene (Kamila); H. Darabi (Hatef); M. Eriksson (Mikael); D. Klevebring (Daniel); M.J. Hooning (Maartje); A. Hollestelle (Antoinette); C.H.M. van Deurzen (Carolien); M. Kriege (Mieke); P. Hall (Per); J. Li (Jingmei); J. Liu (Jianjun); M.K. Humphreys (Manjeet); A. Cox (Angela); S.S. Cross (Simon); M.W.R. Reed (Malcolm); P.D.P. Pharoah (Paul); A.M. Dunning (Alison); M. Shah (Mitul); B. Perkins (Barbara); A. Jakubowska (Anna); J. Lubinski (Jan); K. Jaworska-Bieniek (Katarzyna); K. Durda (Katarzyna); A. Ashworth (Alan); A.J. Swerdlow (Anthony ); M. Jones (Michael); M. Schoemaker (Minouk); A. Meindl (Alfons); R.K. Schmutzler (Rita); C. Olswold (Curtis); S. Slager (Susan); A.E. Toland (Amanda); D. Yannoukakos (Drakoulis); K.R. Muir (K.); A. Lophatananon (Artitaya); S. Stewart-Brown (Sarah); P. Siriwanarangsan (Pornthep); K. Matsuo (Keitaro); H. Ito (Hidema); H. Iwata (Hisato); J. Ishiguro (Junko); A.H. Wu (Anna H.); C.-C. Tseng (Chiu-chen); D. Van Den Berg (David); D.O. Stram (Daniel O.); S.-H. Teo (Soo-Hwang); C.H. Yip (Cheng Har); P. Kang (Peter); M.K. Ikram (Kamran); X.-O. Shu (Xiao-Ou); W. Lu (Wei); Y. Gao; H. Cai (Hui); D. Kang (Daehee); J.-Y. Choi (J.); S.K. Park (Sue); D-Y. Noh (Dong-Young); J.M. Hartman (Joost); X. Miao; W.-Y. Lim (Wei-Yen); S.C. Lee (Soo Chin); S. Sangrajrang (Suleeporn); V. Gaborieau (Valerie); P. Brennan (Paul); J.D. McKay (James); P.-E. Wu (Pei-Ei); M.-F. Hou (Ming-Feng); J-C. Yu (Jyh-Cherng); C-Y. Shen (Chen-Yang); W.J. Blot (William); Q. Cai (Qiuyin); L.B. Signorello (Lisa B.); C. Luccarini (Craig); C. Bayes (Caroline); S. Ahmed (Shahana); M. Maranian (Melanie); S. Healey (Sue); A. González-Neira (Anna); G. Pita (Guillermo); M. Rosario Alonso; N. Álvarez (Nuria); D. Herrero (Daniel); D.C. Tessier (Daniel C.); D. Vincent (Daniel); F. Bacot (Francois); D. Hunter (David); S. Lindstrom (Stephen); J. Dennis (Joe); K. Michailidou (Kyriaki); M.K. Bolla (Manjeet); D.F. Easton (Douglas); I. dos Santos Silva (Isabel); O. Fletcher (Olivia); J. Peto (Julian)

2015-01-01

textabstractWe recently identified a novel susceptibility variant, rs865686, for estrogen-receptor positive breast cancer at 9q31.2. Here, we report a fine-mapping analysis of the 9q31.2 susceptibility locus using 43 160 cases and 42 600 controls of European ancestry ascertained from 52 studies and

Beyond imperviousness: A statistical approach to identifying functional differences between development morphologies on variable source area-type response in urbanized watersheds

Science.gov (United States)

Lim, T. C.

2016-12-01

Empirical evidence has shown linkages between urbanization, hydrological regime change, and degradation of water quality and aquatic habitat. Percent imperviousness, has long been suggested as the dominant source of these negative changes. However, recent research identifying alternative pathways of runoff production at the watershed scale have called into question percent impervious surface area's primacy in urban runoff production compared to other aspects of urbanization including change in vegetative cover, imported water and water leakages, and the presence of drainage infrastructure. In this research I show how a robust statistical methodology can detect evidence of variable source area (VSA)-type hydrologic response associated with incremental hydraulic connectivity in watersheds. I then use logistic regression to explore how evidence of VSA-type response relates to the physical and meterological characteristics of the watershed. I find that impervious surface area is highly correlated with development, but does not add significant explanatory power beyond percent developed in predicting VSA-type response. Other aspects of development morphology, including percent developed open space and type of drainage infrastructure also do not add to the explanatory power of undeveloped land in predicting VSA-type response. Within only developed areas, the effect of developed open space was found to be more similar to that of total impervious area than to undeveloped land. These findings were consistent when tested across a national cross-section of urbanized watersheds, a higher resolution dataset of Baltimore Metropolitan Area watersheds, and a subsample of watersheds confirmed not to be served by combined sewer systems. These findings suggest that land development policies that focus on lot coverage should be revisited, and more focus should be placed on preserving native vegetation and soil conditions alongside development.

Can "Federal Sanctuaries" be identified in Triphylia and Arkadia?

DEFF Research Database (Denmark)

Nielsen, Thomas Heine

2013-01-01

This paper discusses whether federal sanctuaries - such as are known from the Achaian and Aitolian Federations - can be identified in Triphylia and Arkadia in the Peloponnese. It is concluded that on present evidence it is not possible to identify such sanctuaries in these areas......This paper discusses whether federal sanctuaries - such as are known from the Achaian and Aitolian Federations - can be identified in Triphylia and Arkadia in the Peloponnese. It is concluded that on present evidence it is not possible to identify such sanctuaries in these areas...

First additional language teaching in the foundation phase of schools in disadvantaged areas

Directory of Open Access Journals (Sweden)

Ellen Lenyai

2011-12-01

Full Text Available Second language learning in South African schools is of supreme importance given the multilingual nature of the country. However, there is no certainty that teachers in the foundation phase of schools in poor environments have the skills to teach literacy in the first additional language and produce competent learners. This investigation revealed that the methods that teachers used to teach English, as the first additional language did not develop children’s comprehension and communication skills. It argues that if teachers do not use methods that encourage children to communicate in English the children might not acquire the competence needed to use English as the language for learning in Grade 4. Policy makers are advised to monitor the implementation of the first additional language policy and to oversee the development of an English literacy-training programme in the foundation phase that could provide teachers with the necessary skills and appropriate approaches for teaching the target language.

Identifying Human Trafficking Victims on a Psychiatry Inpatient Service: a Case Series.

Science.gov (United States)

Nguyen, Phuong T; Lamkin, Joanna; Coverdale, John H; Scott, Samuel; Li, Karen; Gordon, Mollie R

2018-06-01

Human trafficking is a serious and prevalent human rights violation that closely intersects with mental health. Limited empirical attention has been paid to the presentations and identification of trafficking victims in psychiatric settings. The primary goal of this paper is to describe the varied presentations of trafficking victims on an urban inpatient psychiatric unit. A literature review was conducted to identify relevant empirical articles to inform our examination of cases. Adult inpatient cases meeting criteria for known or possible human trafficking were systematically identified and illustrative cases were described. Six cases were identified including one male and five females. Two had been labor trafficked and four were suspected or confirmed to have been sex trafficked. The cases demonstrated a tremendous diversity of demographic and psychiatric identifying factors. These cases indicate the importance of routinely screening for trafficking victims in inpatient psychiatry settings. Identification of cases is a requisite step in providing informed and evidence-based treatments and enabling the secondary prevention of re-exploitation. Additional research is warranted given the limited current empirical research on this topic area.

Identifying the sources of nitrate contamination of groundwater in an agricultural area (Haean basin, Korea) using isotope and microbial community analyses

Energy Technology Data Exchange (ETDEWEB)

Kim, Heejung [School of Earth and Environmental Sciences (BK21 SEES), Seoul National University, Seoul 151–747 (Korea, Republic of); Kaown, Dugin, E-mail: dugin1@snu.ac.kr [School of Earth and Environmental Sciences (BK21 SEES), Seoul National University, Seoul 151–747 (Korea, Republic of); Mayer, Bernhard [Department of Geoscience, University of Calgary, 2500 University Drive NW, Calgary T2N 1N4, Alberta (Canada); Lee, Jin-Yong [Department of Geology, Kangwon National University, Chuncheon 200–701 (Korea, Republic of); Hyun, Yunjung [Planning and Management Group, Korea Environment Institute, Sejong 339-007 (Korea, Republic of); Lee, Kang-Kun [School of Earth and Environmental Sciences (BK21 SEES), Seoul National University, Seoul 151–747 (Korea, Republic of)

2015-11-15

An integrated study based on hydrogeochemical, microbiological and dual isotopic approaches for nitrate and sulfate was conducted to elucidate sources and biogeochemical reactions governing groundwater contaminants in different seasons and under different land use in a basin of Korea. The land use in the study area is comprised of forests (58.0%), vegetable fields (27.6%), rice paddy fields (11.4%) and others (3.0%). The concentrations of NO{sub 3}–N and SO{sub 4}{sup 2−} in groundwater in vegetable fields were highest with 4.2–15.2 mg L{sup −1} and 1.6–19.7 mg L{sup −1} respectively, whereas under paddy fields NO{sub 3}–N concentrations ranged from 0 to 10.7 mg L{sup −1} and sulfate concentrations were ~ 15 mg L{sup −1}. Groundwater with high NO{sub 3}–N concentrations of > 10 mg L{sup −1} had δ{sup 15}N–NO{sub 3}{sup −} values ranging from 5.2 to 5.9‰ and δ{sup 18}O values of nitrate between 2.7 and 4.6‰ suggesting that the nitrate was mineralized from soil organic matter that was amended by fertilizer additions. Elevated concentrations of SO{sub 4}{sup 2−} with δ{sup 34}S–SO{sub 4}{sup 2−} values between 1 and 6‰ in aquifers in vegetable fields indicated that a mixture of sulfate from atmospheric deposition, mineralization of soil organic matter and from synthetic fertilizers is the source of groundwater sulfate. Elevated δ{sup 18}O–NO{sub 3}{sup −} and δ{sup 18}O–SO{sub 4}{sup 2−} values in samples collected from the paddy fields indicated that denitrification and bacterial sulfate reduction are actively occurring removing sulfate and nitrate from the groundwater. This was supported by high occurrences of denitrifying and sulfate reducing bacteria in groundwater of the paddy fields as evidenced by 16S rRNA pyrosequencing analysis. This study shows that dual isotope techniques combined with microbial data can be a powerful tool for identification of sources and microbial processes affecting NO{sub 3}{sup �

Tools to identify linear combination of prognostic factors which maximizes area under receiver operator curve.

Science.gov (United States)

Todor, Nicolae; Todor, Irina; Săplăcan, Gavril

2014-01-01

The linear combination of variables is an attractive method in many medical analyses targeting a score to classify patients. In the case of ROC curves the most popular problem is to identify the linear combination which maximizes area under curve (AUC). This problem is complete closed when normality assumptions are met. With no assumption of normality search algorithm are avoided because it is accepted that we have to evaluate AUC n(d) times where n is the number of distinct observation and d is the number of variables. For d = 2, using particularities of AUC formula, we described an algorithm which lowered the number of evaluations of AUC from n(2) to n(n-1) + 1. For d > 2 our proposed solution is an approximate method by considering equidistant points on the unit sphere in R(d) where we evaluate AUC. The algorithms were applied to data from our lab to predict response of treatment by a set of molecular markers in cervical cancers patients. In order to evaluate the strength of our algorithms a simulation was added. In the case of no normality presented algorithms are feasible. For many variables computation time could be increased but acceptable.

Investigation of the contamination induced by the cars travelling in the restricted area

International Nuclear Information System (INIS)

Kinomura, Koji; Yamada, Norikazu; Inoue, Ryo

2012-12-01

Traffic on the Route 6 will increase after the revision of the evacuation area and the restricted one. The purpose of this investigation is to study on the contamination induced by cars travelling in the current restricted area. This study focuses on the police cars patrolling all over the restricted area, whose total number is up to 101 cars. The measurement issues are shown as the following, 1. Background contamination, 2. Initial contamination of a car, regarding a radiator, a tire and a tire-house in the front and the rear, just before going into the restricted area, 3. Subsequent contamination of the same parts just after leaving the area, 4. Question about the travelling routes, the districts, and the environmental conditions of every car. Each background contamination at 1cm, 30cm and 1.0m height shows about 200 cpm and keeps stable. The histogram of the contamination difference between the initial and the subsequent one corresponds to normal distribution, whose mean value lies about zero in the measurement cases of the radiators and the front and rear tires of all the cars. It means that no additional contamination by travelling in the restricted area has occurred on such parts. On other hands, the possibility of additional contamination which exceeds 500 cpm per day has been suggested particulary on the tire-houses. The contamination difference of the car travelling on roads between with and without pavements has not been identified as well as in weather conditions at least based on the obtained histograms. Eventually, patrolling around the restricted area or passing mountainous zones in the area has been recognized as a common factors which increases additional contamination to more than 500 cpm per day, but in such a case the accumulated contamination trend with daily travelling has not been identified. The average contamination level basically remains low against the screening one, 13,000 cpm, defined in the regulation. However, much attention should be

[Total analysis of organic rubber additives].

Science.gov (United States)

He, Wen-Xuan; Robert, Shanks; You, Ye-Ming

2010-03-01

In the present paper, after middle pressure chromatograph separation using both positive phase and reversed-phase conditions, the organic additives in ethylene-propylene rubber were identified by infrared spectrometer. At the same time, by using solid phase extraction column to maintain the main component-fuel oil in organic additves to avoid its interfering with minor compounds, other organic additves were separated and analysed by GC/Ms. In addition, the remaining active compound such as benzoyl peroxide was identified by CC/Ms, through analyzing acetone extract directly. Using the above mentioned techniques, soften agents (fuel oil, plant oil and phthalte), curing agent (benzoylperoxide), vulcanizing accelerators (2-mercaptobenzothiazole, ethyl thiuram and butyl thiuram), and antiagers (2, 6-Di-tert-butyl-4-methyl phenol and styrenated phenol) in ethylene-propylene rubber were identified. Although the technique was established in ethylene-propylene rubber system, it can be used in other rubber system.

Environmental analysis of geopressured-geothermal prospect areas, De Witt and Colorado counties, Texas. Final report, March 1 - August 31, 1979

Energy Technology Data Exchange (ETDEWEB)

Gustavson, T.C.; Reeder, F.S.; Badger, E.A.

1980-02-01

Information collected and analyzed for a preliminary environmental analysis of geopressured geothermal prospect areas in Colorado and DeWitt Counties, Texas is presented. Specific environmental concerns for each geopressured geothermal prospect area are identified and discussed. Approximately 218 km/sup 2/(85 mi/sup 2/) were studied in the vicinity of each prospect area to: (1) conduct an environmental analysis to identify more and less suited areas for geopressured test wells; and (2) provide an environmental data base for future development of geopressured geothermal energy resources. A series of maps and tables are included to illustrate environmental characteristics including: geology, water resources, soils, current land use, vegetation, wildlife, and meteorological characteristics, and additional relevant information on cultural resources, power- and pipelines, and regulatory agencies. A series of transparent overlays at the scale of the original mapping has also been produced for the purposes of identifying and ranking areas of potential conflict between geopressured geothermal development and environmental characteristics. The methodology for ranking suitability of areas within the two prospect areas is discussed in the appendix. (MHR)

Wetland Survey of Selected Areas in the Oak Ridge Y-12 Plant Area of Responsibilty, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Rosensteel.

1997-01-01

This document was prepared to summarize wetland surveys performed in the Y- 1 2 Plant area of responsibility in June and July 1994. Wetland surveys were conducted in three areas within the Oak Ridge Y- 12 Plant area of responsibility in June and July 1994: the Upper East Fork Poplar Creek (UEFPC) Operable Unit (OU), part of the Bear Creek Valley OU (the upper watershed of Bear Creek from the culvert under Bear Creek Road upstream through the Y-12 West End Environmental Management Area, and the catchment of Bear Creek North Tributary 1), and part of Chestnut Ridge OU 2 (the McCoy Branch area south of Bethel Valley Road). Using the criteria and methods set forth in the Wetlands Delineation Manual, 18 wetland areas were identified in the 3 areas surveyed; these areas were classified according to the system developed by Cowardin. Fourteen wetlands and one wetland/pond area that are associated with disturbed or remnant stream channels and seeps were identified in the UEFPC OU. Three wetlands were identified in the Bear Creek Valley OU portion of the survey area. One wetland was identified in the riparian zone of McCoy Branch in the southern portion of Chestnut Ridge OU 2

Youthification in the Metropolitan Area of Cluj

Directory of Open Access Journals (Sweden)

Vlad Cocheci

2018-06-01

Full Text Available This research exercise aims to identify all areas affected by what is now known as ‘youthification’ in the Metropolitan Area of Cluj. Broadly speaking, an area touched by youthification witnesses a massive arrival of young adults, who invest in housing, but only remain there until they age. Youthification is usually the second phase within an encompassing process of gentrification. To gain a clearer picture of this phenomenon, we employed a snapshot of the situation recorded by the Population and Housing Census of 2011. Using this image as a starting point, we then applied statistical thresholds aimed at measuring the presence and intensity of youthification within different areas. Thereafter, we looked at areas exhibiting the same level of youthification, in order to find those common traits of their young adult inhabitants that might prove relevant for their choices in matters of housing. Once completed, our efforts resulted in the first map showing the areas affected by youthification within the Metropolitan Area of Cluj. In addition, we reached the following conclusion: Young adults who live in the city are more likely to still be enrolled in a form of education and less likely to be married or to have children than those who live in the suburbs or in rural areas. This observation implies that there might be some hidden dependency relations, which are at work in shaping the choice of housing.

Delimiting areas of endemism through kernel interpolation.

Science.gov (United States)

Oliveira, Ubirajara; Brescovit, Antonio D; Santos, Adalberto J

2015-01-01

We propose a new approach for identification of areas of endemism, the Geographical Interpolation of Endemism (GIE), based on kernel spatial interpolation. This method differs from others in being independent of grid cells. This new approach is based on estimating the overlap between the distribution of species through a kernel interpolation of centroids of species distribution and areas of influence defined from the distance between the centroid and the farthest point of occurrence of each species. We used this method to delimit areas of endemism of spiders from Brazil. To assess the effectiveness of GIE, we analyzed the same data using Parsimony Analysis of Endemism and NDM and compared the areas identified through each method. The analyses using GIE identified 101 areas of endemism of spiders in Brazil GIE demonstrated to be effective in identifying areas of endemism in multiple scales, with fuzzy edges and supported by more synendemic species than in the other methods. The areas of endemism identified with GIE were generally congruent with those identified for other taxonomic groups, suggesting that common processes can be responsible for the origin and maintenance of these biogeographic units.

Delimiting areas of endemism through kernel interpolation.

Directory of Open Access Journals (Sweden)

Ubirajara Oliveira

Full Text Available We propose a new approach for identification of areas of endemism, the Geographical Interpolation of Endemism (GIE, based on kernel spatial interpolation. This method differs from others in being independent of grid cells. This new approach is based on estimating the overlap between the distribution of species through a kernel interpolation of centroids of species distribution and areas of influence defined from the distance between the centroid and the farthest point of occurrence of each species. We used this method to delimit areas of endemism of spiders from Brazil. To assess the effectiveness of GIE, we analyzed the same data using Parsimony Analysis of Endemism and NDM and compared the areas identified through each method. The analyses using GIE identified 101 areas of endemism of spiders in Brazil GIE demonstrated to be effective in identifying areas of endemism in multiple scales, with fuzzy edges and supported by more synendemic species than in the other methods. The areas of endemism identified with GIE were generally congruent with those identified for other taxonomic groups, suggesting that common processes can be responsible for the origin and maintenance of these biogeographic units.

An Aerial Radiological Survey of the Nevada Test Site - Area 10 Corrective Action Unit 367

International Nuclear Information System (INIS)

Lyons, Craig

2010-01-01

A series of aerial radiological surveys were conducted over the Sedan, Uncle, and Ess ground zero areas in Area 10. The surveys were performed in November 2009 utilizing a large array of helicopter mounted sodium iodide detectors. The purpose of the survey was to update the previous radiological survey levels of the environment and surrounding areas of the ground zeros. Gross Counts, inferred exposure rates, man-made activity, and Americium-241 activity, as calculated from the aerial data are presented in the form of isopleth maps superimposed on imagery of the surveyed areas. In addition, spectral products are included that identify Cesium-137, Americium-241 and Cobalt-60 as the primary radionuclides present within the survey area.

Topology Optimization for Additive Manufacturing

DEFF Research Database (Denmark)

Clausen, Anders

This PhD thesis deals with the combination of topology optimization and additive man-ufacturing (AM, also known as 3D-printing). In addition to my own works, the thesis contains a broader review and assessment of the literature within the field. The thesis first presents a classification...... of the various AM technologies, a review of relevant manufacturing materials, the properties of these materials in the additively manufactured part, as well as manufacturing constraints with a potential for design optimization. Subsequently, specific topology optimization formulations relevant for the most im...... for scalable manufacturing. In relation to interface problems it is shown how a flexible void area may be included into a standard minimum compliance problem by employing an additional design variable field and a sensitivity filter. Furthermore, it is shown how the design of coated structures may be modeled...

Assessment of Offshore Wind Energy Leasing Areas for the BOEM New Jersey Wind Energy Area

Energy Technology Data Exchange (ETDEWEB)

Musial, W.; Elliott, D.; Fields, J.; Parker, Z.; Scott, G.; Draxl, C.

2013-10-01

The National Renewable Energy Laboratory (NREL), under an interagency agreement with the U.S. Department of the Interior's Bureau of Ocean Energy Management (BOEM), is providing technical assistance to identify and delineate leasing areas for offshore wind energy development within the Atlantic Coast Wind Energy Areas (WEAs) established by BOEM. This report focuses on NREL's development and evaluation of the delineations for the New Jersey (NJ) WEA. The overarching objective of this study is to develop a logical process by which the New Jersey WEA can be subdivided into non-overlapping leasing areas for BOEM's use in developing an auction process in a renewable energy lease sale. NREL identified a selection of leasing areas and proposed delineation boundaries within the established NJ WEA. The primary output of the interagency agreement is this report, which documents the methodology, including key variables and assumptions, by which the leasing areas were identified and delineated.

Biotic and Climatic Velocity Identify Contrasting Areas of Vulnerability to Climate Change

Science.gov (United States)

Carroll, Carlos; Lawler, Joshua J.; Roberts, David R.; Hamann, Andreas

2015-01-01

Metrics that synthesize the complex effects of climate change are essential tools for mapping future threats to biodiversity and predicting which species are likely to adapt in place to new climatic conditions, disperse and establish in areas with newly suitable climate, or face the prospect of extirpation. The most commonly used of such metrics is the velocity of climate change, which estimates the speed at which species must migrate over the earth’s surface to maintain constant climatic conditions. However, “analog-based” velocities, which represent the actual distance to where analogous climates will be found in the future, may provide contrasting results to the more common form of velocity based on local climate gradients. Additionally, whereas climatic velocity reflects the exposure of organisms to climate change, resultant biotic effects are dependent on the sensitivity of individual species as reflected in part by their climatic niche width. This has motivated development of biotic velocity, a metric which uses data on projected species range shifts to estimate the velocity at which species must move to track their climatic niche. We calculated climatic and biotic velocity for the Western Hemisphere for 1961–2100, and applied the results to example ecological and conservation planning questions, to demonstrate the potential of such analog-based metrics to provide information on broad-scale patterns of exposure and sensitivity. Geographic patterns of biotic velocity for 2954 species of birds, mammals, and amphibians differed from climatic velocity in north temperate and boreal regions. However, both biotic and climatic velocities were greatest at low latitudes, implying that threats to equatorial species arise from both the future magnitude of climatic velocities and the narrow climatic tolerances of species in these regions, which currently experience low seasonal and interannual climatic variability. Biotic and climatic velocity, by approximating

Quantifying the relative irreplaceability of important bird and biodiversity areas.

Science.gov (United States)

Di Marco, Moreno; Brooks, Thomas; Cuttelod, Annabelle; Fishpool, Lincoln D C; Rondinini, Carlo; Smith, Robert J; Bennun, Leon; Butchart, Stuart H M; Ferrier, Simon; Foppen, Ruud P B; Joppa, Lucas; Juffe-Bignoli, Diego; Knight, Andrew T; Lamoreux, John F; Langhammer, Penny F; May, Ian; Possingham, Hugh P; Visconti, Piero; Watson, James E M; Woodley, Stephen

2016-04-01

World governments have committed to increase the global protected areas coverage by 2020, but the effectiveness of this commitment for protecting biodiversity depends on where new protected areas are located. Threshold- and complementarity-based approaches have been independently used to identify important sites for biodiversity. We brought together these approaches by performing a complementarity-based analysis of irreplaceability in important bird and biodiversity areas (IBAs), which are sites identified using a threshold-based approach. We determined whether irreplaceability values are higher inside than outside IBAs and whether any observed difference depends on known characteristics of the IBAs. We focused on 3 regions with comprehensive IBA inventories and bird distribution atlases: Australia, southern Africa, and Europe. Irreplaceability values were significantly higher inside than outside IBAs, although differences were much smaller in Europe than elsewhere. Higher irreplaceability values in IBAs were associated with the presence and number of restricted-range species; number of criteria under which the site was identified; and mean geographic range size of the species for which the site was identified (trigger species). In addition, IBAs were characterized by higher irreplaceability values when using proportional species representation targets, rather than fixed targets. There were broadly comparable results when measuring irreplaceability for trigger species and when considering all bird species, which indicates a good surrogacy effect of the former. Recently, the International Union for Conservation of Nature has convened a consultation to consolidate global standards for the identification of key biodiversity areas (KBAs), building from existing approaches such as IBAs. Our results informed this consultation, and in particular a proposed irreplaceability criterion that will allow the new KBA standard to draw on the strengths of both threshold- and

A survey of sandflies in the affected areas of leishmaniasis, southern Thailand.

Science.gov (United States)

Sukra, Kotchapan; Kanjanopas, Kobkarn; Amsakul, Sakultip; Rittaton, Virot; Mungthin, Mathirut; Leelayoova, Saovanee

2013-01-01

Leishmania siamensis was firstly described as a causative agent of autochthonous visceral leishmaniasis in southern provinces of Thailand since 2008. The spread of leishmaniasis depends on the distribution of the vectors and reservoir hosts. Unfortunately, little is known about these vital factors. The objective of this study was to identify the distribution of sandfly species, their density, and their habitats in the affected areas of leishmaniasis, southern Thailand. A cross-sectional survey of sandflies was conducted in three provinces of southern Thailand where leishmaniasis cases were previously reported. The collection of sandflies was performed using CDC light traps for four consecutive months, from March to June 2009. A total of 2,698 sandflies were collected in the affected areas. Among 1,451 female sandflies, six species of genus Sergentomyia were identified, i.e., Sergentomyia gemmea, Sergentomyia iyengari, Sergentomyia barraudi, Sergentomyia indica, Sergentomyia silvatica, and Sergentomyia perturbans. S. gemmea (81.4 %) was the most predominant species in all areas. In addition, one species of the genus Phlebotomus, Phlebotomus argentipes, a known vector of leishmaniasis was also detected. The distribution of sandfly species in these leishmaniasis-affected areas was different from the previous studies in other areas of Thailand. Further studies are needed to proof whether these sandflies can be the natural vectors of leishmaniasis.

Do Quiet Areas Afford Greater Health-Related Quality of Life than Noisy Areas?

Directory of Open Access Journals (Sweden)

Kim N. Dirks

2013-03-01

Full Text Available People typically choose to live in quiet areas in order to safeguard their health and wellbeing. However, the benefits of living in quiet areas are relatively understudied compared to the burdens associated with living in noisy areas. Additionally, research is increasingly focusing on the relationship between the human response to noise and measures of health and wellbeing, complementing traditional dose-response approaches, and further elucidating the impact of noise and health by incorporating human factors as mediators and moderators. To further explore the benefits of living in quiet areas, we compared the results of health-related quality of life (HRQOL questionnaire datasets collected from households in localities differentiated by their soundscapes and population density: noisy city, quiet city, quiet rural, and noisy rural. The dose-response relationships between noise annoyance and HRQOL measures indicated an inverse relationship between the two. Additionally, quiet areas were found to have higher mean HRQOL domain scores than noisy areas. This research further supports the protection of quiet locales and ongoing noise abatement in noisy areas.

Identifying areas suitable for wine tourism through the use of multi-criteria and geographic information system: the method and its application in the countryside around Mount Etna (Sicily

Directory of Open Access Journals (Sweden)

Lara Riguccio

2017-06-01

Full Text Available Vineyards are among the crops that shape quality landscapes. Many places in the world are famous for their unique wine landscapes which play an important role in the development of tourism in the rural areas. Among these, the wine landscape surrounding mount Etna (Sicily emerges due to its undisputed value, as it is an important component of the territory recognised as a World Heritage Site by UNESCO. This work was conducted with that in mind, in order to identify the most suitable areas for wine tourism on the slopes of our volcano. The method used assigns a great importance to the quality of the landscape, an indispensable resource for encouraging wine tourism, and considers it to be of equal importance with the production of the wines themselves. The present work uses multi-criteria analysis in combination with geographic information system (GIS. Numerous indicators describing local resources were weighed and spatialized. The GIS analysis allowed for the development of various intermediate maps, which allowed to draw up the final suitability map for wine tourism, identifying areas larger than those of the actual vineyards. The value of these areas and the quality of their landscapes are closely connected to the production of the wines in the zone. It could be the target for specific plans and projects aimed at using the available resources, to develop wine tourism in rural areas. Although the study only covers a limited geographical area, the methodology used has general validity and could be used in other contexts.

Identifying seizure onset zone from electrocorticographic recordings: A machine learning approach based on phase locking value.

Science.gov (United States)

Elahian, Bahareh; Yeasin, Mohammed; Mudigoudar, Basanagoud; Wheless, James W; Babajani-Feremi, Abbas

2017-10-01

Using a novel technique based on phase locking value (PLV), we investigated the potential for features extracted from electrocorticographic (ECoG) recordings to serve as biomarkers to identify the seizure onset zone (SOZ). We computed the PLV between the phase of the amplitude of high gamma activity (80-150Hz) and the phase of lower frequency rhythms (4-30Hz) from ECoG recordings obtained from 10 patients with epilepsy (21 seizures). We extracted five features from the PLV and used a machine learning approach based on logistic regression to build a model that classifies electrodes as SOZ or non-SOZ. More than 96% of electrodes identified as the SOZ by our algorithm were within the resected area in six seizure-free patients. In four non-seizure-free patients, more than 31% of the identified SOZ electrodes by our algorithm were outside the resected area. In addition, we observed that the seizure outcome in non-seizure-free patients correlated with the number of non-resected SOZ electrodes identified by our algorithm. This machine learning approach, based on features extracted from the PLV, effectively identified electrodes within the SOZ. The approach has the potential to assist clinicians in surgical decision-making when pre-surgical intracranial recordings are utilized. Copyright © 2017 British Epilepsy Association. Published by Elsevier Ltd. All rights reserved.

Leveraging modern climatology to increase adaptive capacity across protected area networks

Science.gov (United States)

Davison, J.E.; Graumlich, L.J.; Rowland, E.L.; Pederson, G.T.; Breshears, D.D.

2012-01-01

Human-driven changes in the global environment pose an increasingly urgent challenge for the management of ecosystems that is made all the more difficult by the uncertain future of both environmental conditions and ecological responses. Land managers need strategies to increase regional adaptive capacity, but relevant and rapid assessment approaches are lacking. To address this need, we developed a method to assess regional protected area networks across biophysically important climatic gradients often linked to biodiversity and ecosystem function. We plot the land of the southwestern United States across axes of historical climate space, and identify landscapes that may serve as strategic additions to current protected area portfolios. Considering climate space is straightforward, and it can be applied using a variety of relevant climate parameters across differing levels of land protection status. The resulting maps identify lands that are climatically distinct from existing protected areas, and may be utilized in combination with other ecological and socio-economic information essential to collaborative landscape-scale decision-making. Alongside other strategies intended to protect species of special concern, natural resources, and other ecosystem services, the methods presented herein provide another important hedging strategy intended to increase the adaptive capacity of protected area networks. ?? 2011 Elsevier Ltd.

Area-to-Area Poisson Kriging and Spatial Bayesian Analysis

Science.gov (United States)

Asmarian, Naeimehossadat; Jafari-Koshki, Tohid; Soleimani, Ali; Taghi Ayatollahi, Seyyed Mohammad

2016-10-01

Background: In many countries gastric cancer has the highest incidence among the gastrointestinal cancers and is the second most common cancer in Iran. The aim of this study was to identify and map high risk gastric cancer regions at the county-level in Iran. Methods: In this study we analyzed gastric cancer data for Iran in the years 2003-2010. Areato- area Poisson kriging and Besag, York and Mollie (BYM) spatial models were applied to smoothing the standardized incidence ratios of gastric cancer for the 373 counties surveyed in this study. The two methods were compared in term of accuracy and precision in identifying high risk regions. Result: The highest smoothed standardized incidence rate (SIR) according to area-to-area Poisson kriging was in Meshkinshahr county in Ardabil province in north-western Iran (2.4,SD=0.05), while the highest smoothed standardized incidence rate (SIR) according to the BYM model was in Ardabil, the capital of that province (2.9,SD=0.09). Conclusion: Both methods of mapping, ATA Poisson kriging and BYM, showed the gastric cancer incidence rate to be highest in north and north-west Iran. However, area-to-area Poisson kriging was more precise than the BYM model and required less smoothing. According to the results obtained, preventive measures and treatment programs should be focused on particular counties of Iran. Creative Commons Attribution License

A systematic literature review of resilience engineering: Research areas and a research agenda proposal

International Nuclear Information System (INIS)

Righi, Angela Weber; Saurin, Tarcisio Abreu; Wachs, Priscila

2015-01-01

Resilience engineering (RE) has been advocated as a new safety management paradigm, compatible with the nature of complex socio-technical systems. This study aims to identify the research areas and to propose a research agenda for RE, based on a systematic literature review that encompasses 237 studies from 2006 to 2014. Six research areas are identified: theory of RE; identification and classification of resilience; safety management tools; analysis of accidents; risk assessment; and training. The area “theory of RE” accounted for 52% of the studies, and it indicates that research has emphasized the description of how resilient performance occurs. The proposal for a research agenda is focused on: refining key constructs; positioning RE in relation to other theories; exploring other research strategies in addition to case-based studies; investigating barriers for implementing RE; and balancing the importance on describing and understanding resilience with the emphasis on the design of resilient systems, and the evaluation of these designs. - Highlights: • Six research areas on RE are identified. • A research agenda for RE is proposed. • RE research is mostly descriptive and based on case studies. • Design science is suggested as a research strategy for RE. • Five domains account for 75% of the reviewed studies

Additive Manufacturing: Multi Material Processing and Part Quality Control

DEFF Research Database (Denmark)

Pedersen, David Bue

This Ph.D dissertation,ffAdditive Manufacturing: Multi Material Processing and Part Quality Controlff, deal with Additive Manufacturing technologies which is a common name for a series of processes that are recognized by being computer controlled, highly automated, and manufacture objects...... by a layered deposition of material. Two areas of particular interest is addressed. They are rooted in two very different areas, yet is intended to fuel the same goal. To help Additive Manufacturing technologies one step closer to becoming the autonomous, digital manufacturing method of tomorrow. Vision...... systems A paradox exist in the field of Additive Manufacturing. The technologies allow for close-to unrestrained and integral geometrical freedom. Almost any geometry can be manufactured fast, e"ciently and cheap. Something that has been missing fundamental capability since the entering of the industrial...

Initial SVE Well Testing for the A-Area Miscellaneous Rubble Pile (ARP) Trenches Area

International Nuclear Information System (INIS)

RIHA, BRIAN

2004-01-01

The A-Area Miscellaneous Rubble Pile (ARP) is a 5.9 acre unit located at the southern end of A/M Area at the Savannah River Site (SRS). Disposal activities at ARP began in the early 1950s. The exact dates of operation and material disposed in the unit remain unknown. Within the ARP exists a smaller, approximately 2 acre, sub unit identified as the Trenches Area. The Trenches Area is dominated by a T-shaped trench (approximately 50 feet wide) containing 8 to 12 feet of ash material. This T-shaped trench will be referred to as the ARP Trench. Vegetation has been removed from the Trenches Area and a lower permeability earthen cover now covers the ARP Trench. The ARP active soil vapor extraction (ASVE) remediation system consists of seven extraction wells and twelve monitoring wells that were pushed into the vadose zone of the ARP Trench. The remediation system was designed based on the pre-design study conducted in 2002. The purpose of the initial soil vapor extraction (SVE) well testing was to verify the integrity and functionality of the nineteen wells installed in the ARP Trench. The well integrity was evaluated based on the flow rate, vacuum, and indication that soil gas and not surface air was pulled from the well. Soil gas was defined as gas with levels of carbon dioxide (CO2) above ambient concentrations (400-700 ppmv). Volatile organic compound (VOC) concentrations were measured at each well to determine the initial distribution of the contamination. In addition, the subsurface vacuum distribution was measured around each extraction well as a relative measure of the influence of each well

Development of a code MOGRA for predicting the migration of ground additions and its application to various land utilization areas

International Nuclear Information System (INIS)

Amano, Hikaru; Uchida, Shigeo; Matsuoka, Syungo; Ikeda, Hiroshi; Hayashi, Hiroko; Kurosawa, Naohiro

2003-01-01

A Code MOGRA (Migration Of GRound Additions) is a migration prediction code for toxic ground additions including radioactive materials in a terrestrial environment, which consists of computational codes that are applicable to various evaluation target systems, and can be used on personal computers. The computational code has the dynamic compartment analysis block at its core, the graphical user interface (GUI) for model formation, computation parameter settings, and results displays. The compartments are obtained by classifying various natural environments into groups that exhibit similar properties. The functionality of MOGRA is being verified by applying it in the analyses of the migration rates of radioactive substances from the atmosphere to soils and plants and flow rates into the rivers. In this report, a hypothetical combination of land usage was supposed to check the function of MOGRA. The land usage was consisted from cultivated lands, forests, uncultivated lands, urban area, river, and lake. Each land usage has its own inside model which is basic module. Also supposed was homogeneous contamination of the surface land from atmospheric deposition of 137 Cs(1.0Bq/m 2 ). The system analyzed the dynamic changes of 137 Cs concentrations in each compartment, fluxes from one compartment to another compartment. (author)

Challenges in Additive Manufacturing of Alumina

OpenAIRE

Gonzalez, Hugo

2016-01-01

Additive manufacturing is seen by many as the holy grail of manufacturing, the ability to produce parts nearly autonomously. Adding material rather than removing it would eliminate the need for expensive resources and machining. The recent expiration of key 3D printing patents has led to many advances in the field and has dramatically lowered the prices of 3D printers, making them accessible to the average individual. The one area where additive manufacturing is still in its infancy is in cer...

Calibration of Local Area Weather Radar-Identifying significant factors affecting the calibration

DEFF Research Database (Denmark)

Pedersen, Lisbeth; Jensen, Niels Einar; Madsen, Henrik

2010-01-01

A Local Area Weather Radar (LAWR) is an X-band weather radar developed to meet the needs of high resolution rainfall data for hydrological applications. The LAWR system and data processing methods are reviewed in the first part of this paper, while the second part of the paper focuses...... cases when the calibration is based on a factorized 3 parameter linear model instead of a single parameter linear model....

The Current State of Additive Manufacturing in Wind Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Mann, Margaret [National Renewable Energy Lab. (NREL), Golden, CO (United States); Palmer, Sierra [Worcester Polytechnic Institute (WPI), , Worcester, MA (United States); Lee, Dominic [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kurup, Parthiv [National Renewable Energy Lab. (NREL), Golden, CO (United States); Remo, Timothy [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jenne, Dale Scott [National Renewable Energy Lab. (NREL), Golden, CO (United States); Richardson, Bradley S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Love, Lonnie J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Post, Brian K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-12-01

Wind power is an inexhaustible form of energy that is being captured throughout the U.S. to power the engine of our economy. A robust, domestic wind industry promises to increase U.S. industry growth and competitiveness, strengthen U.S. energy security independence, and promote domestic manufacturing nationwide. As of 2016, ~82GW of wind capacity had been installed, and wind power now provides more than 5.5% of the nation’s electricity and supports more than 100,000 domestic jobs, including 500 manufacturing facilities in 43 States. To reach the U.S. Department of Energy’s (DOE’s) 2015 Wind Vision study scenario of wind power serving 35% of the nation's end-use demand by 2050, significant advances are necessary in all areas of wind technologies and market. An area that can greatly impact the cost and rate of innovation in wind technologies is the use of advanced manufacturing, with one of the most promising areas being additive manufacturing (AM). Considering the tremendous promise offered by advanced manufacturing, it is the purpose of this report to identify the use of AM in the production and operation of wind energy systems. The report has been produced as a collaborative effort for the DOE Wind Energy Technology Office (WETO), between Oak Ridge National Laboratory (ORNL) and the National Renewable Energy Laboratory (NREL).

Identifying management competencies for health care executives: review of a series of Delphi studies.

Science.gov (United States)

Hudak, R P; Brooke, P P; Finstuen, K

2000-01-01

This analysis reviews a selected body of research that identifies the essential areas of management expertise required of future health care executives. To ensure consistency, six studies are analyzed, utilizing the Delphi technique, to query a broad spectrum of experts in different fields and sites of health care management. The analysis identifies a number of management competencies, i.e., managerial capabilities, which current and aspiring health care executives, in various settings and with differing educational backgrounds, should possess to enhance the probability of their success in current and future positions of responsibility. In addition, this review identifies the skills (technical expertise), knowledge (facts and principles) and abilities (physical, mental or legal power) required to support achievement of these competencies. Leadership and resource management, including cost and finance dimensions, are the highest-rated requisite management competencies. The dominant skills, knowledge and abilities (SKAs) are related to interpersonal skills. The lowest-rated SKAs are related to job-specific, technical skills. Recommendations include the review of this research by formal and continuing education programs to determine the content of their courses and areas for future research. Similarly, current health care executives should assess this research to assist in identifying competency gaps. Lastly, this analysis recommends that the Delphi technique, as a valid and replicable methodology, be applied toward the study of non-executive health care managers, e.g., students, clinicians, mid-level managers and integrated systems administrators, to determine their requisite management competencies and SKAs.

High Incidence of Mammalian Orthoreovirus Identified by Environmental Surveillance in Taiwan.

Directory of Open Access Journals (Sweden)

Matthew C Y Lim

Full Text Available Wild poliovirus (WPV persists in diverse locales worldwide, spreading outward from endemic areas. In response to the international threat of WPV transmission and changes in the national vaccination policy, we established an environmental surveillance system to monitor the circulation of wild and vaccine-related poliovirus in Taiwan. From July 2012 to December 2013, we collected sewage specimens every month from 10 sewage treatment plants located throughout Taiwan. The specimens were concentrated by the two-phase separation method and then inoculated into L20B, RD, and A549 cells for virus isolation. Viral isolates were identified and serotyped by immunofluorescence assay or molecular analysis. A total of 300 sewage samples were collected, and the results showed 163 samples (54.3% were positive for virus, and 268 isolates were identified. Among these, 75 samples (25% were positive for enterovirus (EV, but no poliovirus was found. In addition, 92 isolates were identified as enteroviruses and the most common serotypes were coxsackievirus B4, coxsackievirus B3, and coxsackievirus B2. Interestingly, 102 (34% and 82 (27.3% specimens were positive for mammalian orthoreovirus (MRV and adenovirus, respectively. This study confirmed that sewage surveillance can be a useful additional modality for monitoring the possible presence of wild-type or vaccine-derived poliovirus in wastewater, and can indicate the current types of viruses circulating in the population. Furthermore, since MRV was found in children with acute necrotizing encephalopathy and meningitis, the high incidence of MRV detected by environmental surveillance warrants further investigation.

Floristic study of AqDagh sanctuary in Marakan protected area: west Azarbaijan province, Iran

Directory of Open Access Journals (Sweden)

Hanieh Nafisi

2015-01-01

Full Text Available AqDagh sanctuary with the area 5184.7 hectares area is one of the three sanctuaries in the Marakan protected area, in west Azarbaijan province. It is located in the semi-dry to cold semi-dry climates. In this research, 227 taxa (species, subspecies and varieties belonging to 47 families and 166 genera were identified during 2008 through 2009. Among the studied plants, 205 dicots and 21 monocots and one gymnosperm were recognized. Asteraceae (with 30 species and Lamiaceae (with 26 species were the largest families followed by Brassicaceae, Caryophylaceae and Fabaceae. Astragalus (with 9 species and Gallium (with 5 species were the most diverse genera. Twenty one endemic and 6 rare taxa plus 2 monotypic genera were identified in the studied area. In addition, 11 taxa from northwest of Iran and 29 from west Azarbaijan were reported for the first time. Therophytes (with 36.57% comprised the most dominant life form, followed by hemicryptophytes (with 27.75% in this area. From the chorological point of the view, most of the flora has been influenced by the IT (31.53% and IT-ES (27.49% elements. The highest proportion of vegetation in this area belonged to bi-tri or pluriregional elements (with 59.01%.

Using Chief Complaint in Addition to Diagnosis Codes to Identify Falls in the Emergency Department.

Science.gov (United States)

Patterson, Brian W; Smith, Maureen A; Repplinger, Michael D; Pulia, Michael S; Svenson, James E; Kim, Michael K; Shah, Manish N

2017-09-01

To compare incidence of falls in an emergency department (ED) cohort using a traditional International Classification of Diseases, Ninth Revision (ICD-9) code-based scheme and an expanded definition that included chief complaint information and to examine the clinical characteristics of visits "missed" in the ICD-9-based scheme. Retrospective electronic record review. Academic medical center ED. Individuals aged 65 and older seen in the ED between January 1, 2013, and September 30, 2015. Two fall definitions were applied (individually and together) to the cohort: an ICD-9-based definition and a chief complaint definition. Admission rates and 30-day mortality (per encounter) were measured for each definition. Twenty-three thousand eight hundred eighty older adult visits occurred during the study period. Using the most-inclusive definition (ICD-9 code or chief complaint indicating a fall), 4,363 visits (18%) were fall related. Of these visits, 3,506 (80%) met the ICD-9 definition for a fall-related visit, and 2,664 (61%) met the chief complaint definition. Of visits meeting the chief complaint definition, 857 (19.6%) were missed when applying the ICD-9 definition alone. Encounters missed using the ICD-9 definition were less likely to lead to an admission (42.9%, 95% confidence interval (CI) = 39.7-46.3%) than those identified (54.4%, 95% CI = 52.7-56.0%). Identifying individuals in the ED who have fallen based on diagnosis codes underestimates the true burden of falls. Individuals missed according to the code-based definition were less likely to have been admitted than those who were captured. These findings call attention to the value of using chief complaint information to identify individuals who have fallen in the ED-for research, clinical care, or policy reasons. © 2017, Copyright the Authors Journal compilation © 2017, The American Geriatrics Society.

[Emotion and Brodmann's areas: special reference on area 12].

Science.gov (United States)

Kawamura, Mitsuru

2010-11-01

Brodmann's brain maps, assembled in 1909, are still in use, but understanding of their animal-human homology is uncertain. Furthermore, in 1909, Brodmann did not identify human Area 12 (BA12); a location now important to understanding of frontotemporal lobar degeneration (FTLD) and emotional function. We found Brodmann did identify human BA12 in later maps (1910 and 1914), not in the 1909 monograph. Because of its current link with FTLD, BA 12's translation from animal (1909) to human (1910 and 1914) is not only an historical puzzle. It impacts how Brodmann's areas, based on comparative animal-human cyto-architecture, are widely used in current research as functional loci in human brain. If Brodmann's maps are of current value, then an accurate rather than a generic Brodmann number is in order.

Damping control strategies of inter-area low-frequency oscillation for DFIG-based wind farms integrated into a power system

DEFF Research Database (Denmark)

Li, Hui; Liu, Shengquan; Ji, Haiting

2014-01-01

on the power system stabilizer (PSS) control method. Transient simulation on different damping gain coefficients are conducted for justification. Following the OTEF mechanism analysis, an additional fuzzy damping control strategy with the active/reactive power loop is proposed by identifying the oscillation......This study investigates the inter-area low-frequency damping control strategies of a doubly fed induction generator (DFIG)-based wind farm through oscillation transient energy function (OTEF) analysis. Based on the OTEF descent expressions, the feasibility of damping the inter-area low...... oscillation of the wind turbine shaft. The proposed additional fuzzy control strategy with the active/reactive power loop has better damping performance than the presented PSS control, especially for damping the inter-area low-frequency oscillation....

Regional collaboration among Urban Area Security Initiative regions: results of the Johns Hopkins urban area survey.

Science.gov (United States)

Errett, Nicole A; Bowman, Calvin; Barnett, Daniel J; Resnick, Beth A; Frattaroli, Shannon; Rutkow, Lainie

2014-01-01

Regional collaboration has been identified as a potential facilitator of public health preparedness efforts. The Urban Area Security Initiative (UASI) grant program, administered by the Federal Emergency Management Agency (FEMA) since 2003, has provided 64 high-risk metropolitan areas funding to enhance their regional preparedness capabilities. This study describes informal and formal regional collaboration infrastructure, as well as regional collaboration-related activities and assessment methods, in FFY2010 UASI regions. A cross-sectional online survey was administered via Survey Monkey from September through December 2013. Points of contact from FFY2010 funded UASI metropolitan areas completed the survey, with a response rate of 77.8% (n=49). Summary statistics were calculated to describe the current informal and formal regional collaboration infrastructure. Additionally, the cross-sectional survey collected rates of agreement with 8 collaborative preparedness statements at 3 time points. The survey found that UASI regions are engaging in collaborative activities and investments to build capabilities, with most collaboration occurring in the prevention, protection, and response mission areas. Collaborative relationships in preparedness among emergency managers and municipal chief executive officers improved during the FFY2010 UASI performance period compared to the pre-UASI award period, with lasting effects. The majority of UASI regions reported conducting independent assessments of capabilities and their measurement at the UASI region level. Urban areas that received a FFY2010 UASI grant award are engaging in collaborative activities and have established interjurisdictional relationships in preparedness. The use of grant funds to encourage collaboration in preparedness has the potential to leverage limited resources and promote informed investments.

Regional Collaboration Among Urban Area Security Initiative Regions: Results of the Johns Hopkins Urban Area Survey

Science.gov (United States)

Bowman, Calvin; Barnett, Daniel J.; Resnick, Beth A.; Frattaroli, Shannon; Rutkow, Lainie

2014-01-01

Regional collaboration has been identified as a potential facilitator of public health preparedness efforts. The Urban Area Security Initiative (UASI) grant program, administered by the Federal Emergency Management Agency (FEMA) since 2003, has provided 64 high-risk metropolitan areas funding to enhance their regional preparedness capabilities. This study describes informal and formal regional collaboration infrastructure, as well as regional collaboration–related activities and assessment methods, in FFY2010 UASI regions. A cross-sectional online survey was administered via Survey Monkey from September through December 2013. Points of contact from FFY2010 funded UASI metropolitan areas completed the survey, with a response rate of 77.8% (n=49). Summary statistics were calculated to describe the current informal and formal regional collaboration infrastructure. Additionally, the cross-sectional survey collected rates of agreement with 8 collaborative preparedness statements at 3 time points. The survey found that UASI regions are engaging in collaborative activities and investments to build capabilities, with most collaboration occurring in the prevention, protection, and response mission areas. Collaborative relationships in preparedness among emergency managers and municipal chief executive officers improved during the FFY2010 UASI performance period compared to the pre-UASI award period, with lasting effects. The majority of UASI regions reported conducting independent assessments of capabilities and their measurement at the UASI region level. Urban areas that received a FFY2010 UASI grant award are engaging in collaborative activities and have established interjurisdictional relationships in preparedness. The use of grant funds to encourage collaboration in preparedness has the potential to leverage limited resources and promote informed investments. PMID:25398073

Characterization of the Hanford 300 area burial grounds. Decontamination and decommissioning regulatory issues

International Nuclear Information System (INIS)

Morris, F.A.; Smith, R.F.; Phillips, S.J.

1979-03-01

The Hanford 300 Area Burial Grounds characterization project has identified four management alternatives for disposition of the burial grounds. These alternatives are: (1) abandonment, (2) entombment, (3) perpetual care, and (4) exhumation and translocation. Major Federal statutes and regulations that could apply to management alternatives are identified along with the constraints that applicable laws could impose. This analysis includes explicit attention to the uncertainty surrounding various legal constraints. Also specified are legislative developments as well as trends in other agencies and the courts, obtained by review of legislative proceedings, statutes and regulations, that could result in legislation or policies posing additional constraints

Additive Construction using Basalt Regolith Fines

Science.gov (United States)

Mueller, Robert P.; Sibille, Laurent; Hintze, Paul E.; Lippitt, Thomas C.; Mantovani, James G.; Nugent, Matthew W.; Townsend, Ivan I.

2014-01-01

Planetary surfaces are often covered in regolith (crushed rock), whose geologic origin is largely basalt. The lunar surface is made of small-particulate regolith and areas of boulders located in the vicinity of craters. Regolith composition also varies with location, reflecting the local bedrock geology and the nature and efficiency of the micrometeorite-impact processes. In the lowland mare areas (suitable for habitation), the regolith is composed of small granules (20 - 100 microns average size) of mare basalt and volcanic glass. Impacting micrometeorites may cause local melting, and the formation of larger glassy particles, and this regolith may contain 10-80% glass. Studies of lunar regolith are traditionally conducted with lunar regolith simulant (reconstructed soil with compositions patterned after the lunar samples returned by Apollo). The NASA Kennedy Space Center (KSC) Granular Mechanics & Regolith Operations (GMRO) lab has identified a low fidelity but economical geo-technical simulant designated as Black Point-1 (BP-1). It was found at the site of the Arizona Desert Research and Technology Studies (RATS) analog field test site at the Black Point lava flow in adjacent basalt quarry spoil mounds. This paper summarizes activities at KSC regarding the utilization of BP-1 basalt regolith and comparative work with lunar basalt simulant JSC-1A as a building material for robotic additive construction of large structures. In an effort to reduce the import or in-situ fabrication of binder additives, we focused this work on in-situ processing of regolith for construction in a single-step process after its excavation. High-temperature melting of regolith involves techniques used in glassmaking and casting (with melts of lower density and higher viscosity than those of metals), producing basaltic glass with high durability and low abrasive wear. Most Lunar simulants melt at temperatures above 1100 C, although melt processing of terrestrial regolith at 1500 C is not

Improving the design of amphibian surveys using soil data: A case study in two wilderness areas

Science.gov (United States)

Bowen, K.D.; Beever, E.A.; Gafvert, U.B.

2009-01-01

Amphibian populations are known, or thought to be, declining worldwide. Although protected natural areas may act as reservoirs of biological integrity and serve as benchmarks for comparison with unprotected areas, they are not immune from population declines and extinctions and should be monitored. Unfortunately, identifying survey sites and performing long-term fieldwork within such (often remote) areas involves a special set of problems. We used the USDA Natural Resource Conservation Service Soil Survey Geographic (SSURGO) Database to identify, a priori, potential habitat for aquatic-breeding amphibians on North and South Manitou Islands, Sleeping Bear Dunes National Lakeshore, Michigan, and compared the results to those obtained using National Wetland Inventory (NWI) data. The SSURGO approach identified more target sites for surveys than the NWI approach, and it identified more small and ephemeral wetlands. Field surveys used a combination of daytime call surveys, night-time call surveys, and perimeter surveys. We found that sites that would not have been identified with NWI data often contained amphibians and, in one case, contained wetland-breeding species that would not have been found using NWI data. Our technique allows for easy a priori identification of numerous survey sites that might not be identified using other sources of spatial information. We recognize, however, that the most effective site identification and survey techniques will likely use a combination of methods in addition to those described here.

Improving the key biodiversity areas approach for effective conservation planning

CSIR Research Space (South Africa)

Knight, AT

2007-03-01

Full Text Available The key biodiversity areas (KBA) approach aims to identify globally important areas for species conservation. Although a similar methodology has been used successfully to identify important Bird Areas, the authors have identified five limitations...

Rock disposal problems identified

Energy Technology Data Exchange (ETDEWEB)

Knox, R

1978-06-01

Mathematical models are the only way of examining the return of radioactivity from nuclear waste to the environment over long periods of time. Work in Britain has helped identify areas where more basic data is required, but initial results look very promising for final disposal of high level waste in hard rock repositories. A report by the National Radiological Protection Board of a recent study, is examined.

The lost pedestrian: Identifying determinant factors of no-pedestrian phenomenon in the area of Baiturrahman Grand Mosque, Banda Aceh, Indonesia

Science.gov (United States)

Nasution, M. A.

2018-03-01

The area of Baiturrahman Grand Mosque in Banda Aceh has a deep meaning for people of Aceh because it is a historical site, which has many historical heritages. Recently, it is rarely seen people walk along the corridor of the town. People always drive to move along the road and stop right on their destination. Some are still walking, but only for 20-30 meter. On the other hand, a number of the vehicle significantly increase followed by the needs of parking space. The intensity of the traffic is high in day time; in the morning, at noon, and in the late afternoon. The research will be conducted using qualitative and quantitative methods; investigating the change of the environment caused by development, disaster, and conflict, interviewing government as the decision maker and public figure, questionnaires, and finding information from official documents and literature. It is necessary to identify the determinant factors of no-pedestrian phenomenon in the area of Banda Aceh because it is expected to create atmosphere, which encourage people to walk along the city center, revive walking habits to urban community, and strengthen the role of city center as a center of activities; praying, shopping, and engaging in recreation and leisure.

Cortical areas involved in Arabic number reading.

Science.gov (United States)

Roux, F-E; Lubrano, V; Lauwers-Cances, V; Giussani, C; Démonet, J-F

2008-01-15

Distinct functional pathways for processing words and numbers have been hypothesized from the observation of dissociated impairments of these categories in brain-damaged patients. We aimed to identify the cortical areas involved in Arabic number reading process in patients operated on for various brain lesions. Direct cortical electrostimulation was prospectively used in 60 brain mappings. We used object naming and two reading tasks: alphabetic script (sentences and number words) and Arabic number reading. Cortical areas involved in Arabic number reading were identified according to location, type of interference, and distinctness from areas associated with other language tasks. Arabic number reading was sustained by small cortical areas, often extremely well localized (area (Brodmann area 45), the anterior part of the dominant supramarginal gyrus (Brodmann area 40; p area (Brodmann area 37; p areas.

Evaluation of fisher (Pekania pennanti) restoration in Olympic National Park and the Olympic Recovery Area: 2015 final annual progress report

Science.gov (United States)

Happe, Patricia J.; Jenkins, Kurt J.; Kay, Thomas J.; Pilgrim, Kristie; Schwartz, Michael K; Lewis, Jeffrey C.; Aubry, Keith B.

2016-01-01

and 3 new recruits to the population. Three additional fishers were detected with cameras but not DNA, consequently their identities were unknown. All fisher detections were in the target area. Additionally, we identified 46 other species of wildlife at the baited camera stations. We also obtained 4 additional confirmed records of fishers in the study area through photographs provided by the public and incidental live capture. During 2016, we plan to resample 69 hexagons sampled in the target area in 2014 and 12 new hexes in the expansion area. In addition, we plan to sample non-selected hexes in-between hexes where we had a cluster of fishers in 2014, to provide better understanding of occupancy patterns and minimum number of individuals in an area where fishers appear to be concentrating.

[Utility of chromosome banding with ALU I enzyme for identifying methylated areas in breast cancer].

Science.gov (United States)

Rojas-Atencio, Alicia; Yamarte, Leonard; Urdaneta, Karelis; Soto-Alvarez, Marisol; Alvarez Nava, Francisco; Cañizalez, Jenny; Quintero, Maribel; Atencio, Raquel; González, Richard

2012-12-01

Cancer is a group of disorders characterized by uncontrolled cell growth which is produced by two successive events: increased cell proliferation (tumor or neoplasia) and the invasive capacity of these cells (metastasis). DNA methylation is an epigenetic process which has been involved as an important pathogenic factor of cancer. DNA methylation participates in the regulation of gene expression, directly, by preventing the union of transcription factors, and indirectly, by promoting the "closed" structure of the chromatine. The objectives of this study were to identify hypermethyled chromosomal regions through the use of restriction Alu I endonuclease, and to relate cytogenetically these regions with tumor suppressive gene loci. Sixty peripheral blood samples of females with breast cancer were analyzed. Cell cultures were performed and cytogenetic spreads, previously digested with Alu I enzyme, were stained with Giemsa. Chromosomal centromeric and not centromeric regions were stained in 37% of cases. About 96% of stained hypermethyled chromosomal regions (1q, 2q, 6q) were linked with methylated genes associated with breast cancer. In addition, centromeric regions in chromosomes 3, 4, 8, 13, 14, 15 and 17, usually unstained, were found positive to digestion with Alu I enzime and Giemsa staining. We suggest the importance of this technique for the global visualization of the genome which can find methylated genes related to breast cancer, and thus lead to a specific therapy, and therefore a better therapeutic response.

Tables of co-located geothermal-resource sites and BLM Wilderness Study Areas

Energy Technology Data Exchange (ETDEWEB)

Foley, D.; Dorscher, M.

1982-11-01

Matched pairs of known geothermal wells and springs with BLM proposed Wilderness Study Areas (WSAs) were identified by inspection of WSA and Geothermal resource maps for the states of Arizona, California, Colorado, Idaho, Montana, Nevada, New Mexico, Oregon, Utah, Washington and Wyoming. A total of 3952 matches, for geothermal sites within 25 miles of a WSA, were identified. Of these, only 71 (1.8%) of the geothermal sites are within one mile of a WSA, and only an additional 100 (2.5%) are within one to three miles. Approximately three-fourths of the matches are at distances greater than ten miles. Only 12 of the geothermal sites within one mile of a WSA have surface temperatures reported above 50/sup 0/C. It thus appears that the geothermal potential of WSAs overall is minimal, but that evaluation of geothermal resources should be considered in more detail for some areas prior to their designation as Wilderness.

Additive interaction in survival analysis

DEFF Research Database (Denmark)

Rod, Naja Hulvej; Lange, Theis; Andersen, Ingelise

2012-01-01

It is a widely held belief in public health and clinical decision-making that interventions or preventive strategies should be aimed at patients or population subgroups where most cases could potentially be prevented. To identify such subgroups, deviation from additivity of absolute effects...... an empirical example of interaction between education and smoking on risk of lung cancer. We argue that deviations from additivity of effects are important for public health interventions and clinical decision-making, and such estimations should be encouraged in prospective studies on health. A detailed...... is the relevant measure of interest. Multiplicative survival models, such as the Cox proportional hazards model, are often used to estimate the association between exposure and risk of disease in prospective studies. In Cox models, deviations from additivity have usually been assessed by surrogate measures...

[A study of infant mortality rate in Korean rural areas].

Science.gov (United States)

Cho, Y H

1981-10-31

This study was undertaken in an attempt to identify the level of birth and infant death in the KHDI demonstration areas. The objectives of this study were to collect available information on birth and infant death in the KHDI demonstration areas, and estimate actual levels of birth and infant mortality in these areas. Within these areas, events of birth and death are continuously recorded by the field health workers, such as the Family Folder, maternal health service card, and the infant-child health service card. Study areas included all the KHDI demonstration areas (Hongchon, Okgu, Gunee). However, 2 myons in the Okgu area were excluded from the study areas since there was no community health practitioner assigned there. The data were collected by 24 community health practitioners and 80 community health aides in the 3 demonstration areas, according to the survey format. These health workers examined and searched existing records. After filling out the survey questionnaires, these health workers made contact with village health workers, "Li" chiefs, mother's club chiefs, or Saemaul leaders at the village level in order that they might gather additional information on possible items which were omitted. Afterwards, health workers made home visits to selected households which were known to have had births or deaths during the 1 year period between January-December 1979. A review of the activities of the health workers during this study indicated that professional survey workers were needed. In addition, 8 surveyors were employed and trained by KHDI to strengthen field survey efforts; they were dispatched to Hongchon and Okgu for 17 days. A total number of 3302 live births and 120 infant deaths were recorded during 1979. All data collected were tabulated by manual counting in the KHDI office. Infant mortality was estimated to be 36.34/1000 births in the demonstration areas during 1979 (rate in Hongchon Gun was 34.5, 31.0 in Okgu Gun, and 46.2 in Gunee Gun). (author's)

Revegetation increase bird diversity in coastal area of Socorejo, Tuban, East Java - Indonesia

Science.gov (United States)

Lestari, Yeni Indah; Edi, Wasito; Alivvy, Alkautsar; Ibadah, Acib Setia; Sari, Fadina Yuliana; Nuraini, Finda; Yanuar, Ahmad; Satriyono, Agus; Riany, Citra Fitrie; Saptarini, Dian; Muzaki, Farid Kamal

2017-06-01

Study to address positive impact of revegetation program to increasing diversity of bird had been conducted in coastal area of Socorejo, Tuban - Indonesia. Field observation conducted during April 2011 (representing pre-revegetation period), April 2015 and May 2016 (representing post-revegetation period). A belt transect (500 meter long and 50 meter width) was used to survey the abundance and species composition of birds community. In general, we identified at least 51 bird species from three observation times. From 2011 to 2016, the numbers of the birds identified are 23, 37 and 37 species; while the Shannon-Wiener diversity indices (H') are 1.865, 2.071 and 2.957, respectively. In addition, there are 11 national or internationally protected species, 3 Indonesian endemic species and 12 migratory species occurred in the area. As a conclusion, the coastal revegetation program provides positive impact by generating habitat function for bird community.

Trace elements of concern affecting urban agriculture in industrialized areas: A multivariate approach.

Science.gov (United States)

Boente, C; Matanzas, N; García-González, N; Rodríguez-Valdés, E; Gallego, J R

2017-09-01

The urban and peri-urban soils used for agriculture could be contaminated by atmospheric deposition or industrial releases, thus raising concerns about the potential risk to public health. Here we propose a method to evaluate potential soil pollution based on multivariate statistics, geostatistics (kriging), a novel soil pollution index, and bioavailability assessments. This approach was tested in two districts of a highly populated and industrialized city (Gijón, Spain). The soils showed anomalous content of several trace elements, such as As and Pb (up to 80 and 585 mg kg -1 respectively). In addition, factor analyses associated these elements with anthropogenic activity, whereas other elements were attributed to natural sources. Subsequent clustering also facilitated the differentiation between the northern area studied (only limited Pb pollution found) and the southern area (pattern of coal combustion, including simultaneous anomalies of trace elements and benzo(a)pyrene). A normalized soil pollution index (SPI) was calculated by kriging, using only the elements falling above threshold levels; therefore point-source polluted zones in the northern area and diffuse contamination in the south were identified. In addition, in the six mapping units with the highest SPIs of the fifty studied, we observed low bioavailability for most of the elements that surpassed the threshold levels. However, some anomalies of Pb contents and the pollution fingerprint in the central area of the southern grid call for further site-specific studies. On the whole, the combination of a multivariate (geo) statistic approach and a bioavailability assessment allowed us to efficiently identify sources of contamination and potential risks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Strategy paper. Remedial design/remedial action 100 Area. Revision 2

International Nuclear Information System (INIS)

Donahoe, R.L.

1995-10-01

This strategy paper identifies and defines the approach for remedial design and remedial action (RD/RA) for source waste sites in the 100 Area of the Hanford Site, located in southeastern Washington State. This paper provides the basis for the US Department of Energy (DOE) to assess and approve the Environmental Restoration Contractor's (ERC) approach to RD/RA. Additionally, DOE is requesting review/agreement from the US Environmental Protection Agency (EPA) and Washington State Department of Ecology (Ecology) on the strategy presented in this document in order to expedite remedial activities

Identifying pollination service hotspots and coldspots using citizen science data from the Great Sunflower Project

Science.gov (United States)

LeBuhn, G.; Schmucki, R.

2016-12-01

Identifying the spatial patterns of pollinator visitation rates is key to identifying the drivers of differences in pollination service and the areas where pollinator conservation will provide the highest return on investment. However, gathering pollinator abundance data at the appropriate regional and national scales is untenable. As a surrogate, habitat models have been developed to identify areas of pollinator losses but these models have been developed using expert opinion based on foraging and nesting requirements. Thousands of citizen scientists across the United States participating in The Great Sunflower Project (www.GreatSunflower.org) contribute timed counts of pollinator visits to a focal sunflower variety planted in local gardens and green spaces. While these data provide a more direct measure of pollination service to a standardized plant and include a measure of effort, the data are complicated. Each location is sampled at different dates, times and frequencies as well as different points across the local flight season. To overcome this complication, we have used a generalized additive model to generate regional flight curves to calibrate each individual data point and to attain better estimates of pollination service at each site. Using these flight season corrected data, we identify hotspots and cold spots in pollinator service across the United States, evaluate the drivers shaping the spatial patterns and observe how these data align with the results obtained from predictive models that are based on expert knowledge on foraging and nesting habitats.

21 CFR 70.5 - General restrictions on use of color additives.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false General restrictions on use of color additives. 70... GENERAL COLOR ADDITIVES General Provisions § 70.5 General restrictions on use of color additives. (a) Color additives for use in the area of the eye. No listing or certification of a color additive shall be...

Build platform that provides mechanical engagement with additive manufacturing prints

Science.gov (United States)

Elliott, Amelia M.

2018-03-06

A build platform and methods of fabricating an article with such a platform in an extrusion-type additive manufacturing machine are provided. A platform body 202 includes features 204 that extend outward from the body 202. The features 204 define protrusive areas 206 and recessive areas 208 that cooperate to mechanically engage the extruded material that forms the initial layers 220 of an article when the article is being fabricated by a nozzle 12 of the additive manufacturing machine 10.

Identifying state resources and support programs on e-government websites for persons with intellectual and developmental disabilities.

Science.gov (United States)

Fisher, Kathleen M; Peterson, Justin D; Albert, Jon D

2015-01-01

This descriptive cross-sectional study identified resources and programs that are available nationwide on the Internet to support individuals and families with intellectual and developmental disabilities (I/DD), with a focus on intellectual disability. This evaluation included easily identifiable information on specific resources and highlighted unique programs found in individual states that were linked from e-government websites. Researchers documented the ease of access and available information for all 50 states and the District of Columbia. A number of disparities and areas for improvement were recorded for states and I/DD websites. The researchers conclude that a number of additional health and support services will be needed to address the growing needs of this vulnerable population.

Identifying coronary artery disease in asymptomatic middle-aged sportsmen : The additional value of pulse wave velocity

NARCIS (Netherlands)

Braber, Thijs L.; Prakken, Niek H J; Mosterd, Arend; Mali, Willem P Th M; Doevendans, Pieter A F M; Bots, Michiel L.; Velthuis, Birgitta K.

2015-01-01

Background: Cardiovascular screening may benefit middle-aged sportsmen, as coronary artery disease (CAD) is the main cause of exercise-related sudden cardiac death. Arterial stiffness, as measured by pulse wave velocity (PWV), may help identify sportsmen with subclinical CAD. We examined the

78 FR 72028 - Special Regulations, Areas of the National Park System, Curecanti National Recreation Area...

Science.gov (United States)

2013-12-02

...-substantive edits. The final rule revises the section heading for Sec. 7.51 from ``Curecanti Recreation Area... paragraph 7.51(e) to designate three groups of routes and areas where motor vehicles may be used off park...) and (f). The revisions and additions read as follows: Sec. 7.51 Curecanti National Recreation Area...

Identifying fish diversity hot-spots in data-poor situations.

Science.gov (United States)

Fonseca, Vinícius Prado; Pennino, Maria Grazia; de Nóbrega, Marcelo Francisco; Oliveira, Jorge Eduardo Lins; de Figueiredo Mendes, Liana

2017-08-01

One of the more challenging tasks in Marine Spatial Planning (MSP) is identifying critical areas for management and conservation of fish stocks. However, this objective is difficult to achieve in data-poor situations with different sources of uncertainty. In the present study we propose a combination of hierarchical Bayesian spatial models and remotely sensed estimates of environmental variables to be used as flexible and reliable statistical tools to identify and map fish species richness and abundance hot-spots. Results show higher species aggregates in areas with higher sea floor rugosity and habitat complexity, and identify clear richness hot-spots. Our findings identify sensitive habitats through essential and easy-to-use interpretation tools, such as predictive maps, which can contribute to improving management and operability of the studied data-poor situations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Laser speckle contrast imaging identifies ischemic areas on gastric tube reconstructions following esophagectomy

NARCIS (Netherlands)

Milstein, D.M.J.; Ince, C.; Gisbertz, S.S.; Boateng, K.B.; Geerts, B.F.; Hollmann, M.W.; van Berge Henegouwen, M.I.; Veelo, D.P.

2016-01-01

Gastric tube reconstruction (GTR) is a high-risk surgical procedure with substantial perioperative morbidity. Compromised arterial blood supply and venous congestion are believed to be the main etiologic factors associated with early and late anastomotic complications. Identifying low blood

Genetic Susceptibility to Vitiligo: GWAS Approaches for Identifying Vitiligo Susceptibility Genes and Loci

Science.gov (United States)

Shen, Changbing; Gao, Jing; Sheng, Yujun; Dou, Jinfa; Zhou, Fusheng; Zheng, Xiaodong; Ko, Randy; Tang, Xianfa; Zhu, Caihong; Yin, Xianyong; Sun, Liangdan; Cui, Yong; Zhang, Xuejun

2016-01-01

Vitiligo is an autoimmune disease with a strong genetic component, characterized by areas of depigmented skin resulting from loss of epidermal melanocytes. Genetic factors are known to play key roles in vitiligo through discoveries in association studies and family studies. Previously, vitiligo susceptibility genes were mainly revealed through linkage analysis and candidate gene studies. Recently, our understanding of the genetic basis of vitiligo has been rapidly advancing through genome-wide association study (GWAS). More than 40 robust susceptible loci have been identified and confirmed to be associated with vitiligo by using GWAS. Most of these associated genes participate in important pathways involved in the pathogenesis of vitiligo. Many susceptible loci with unknown functions in the pathogenesis of vitiligo have also been identified, indicating that additional molecular mechanisms may contribute to the risk of developing vitiligo. In this review, we summarize the key loci that are of genome-wide significance, which have been shown to influence vitiligo risk. These genetic loci may help build the foundation for genetic diagnosis and personalize treatment for patients with vitiligo in the future. However, substantial additional studies, including gene-targeted and functional studies, are required to confirm the causality of the genetic variants and their biological relevance in the development of vitiligo. PMID:26870082

Using Workflow Modeling to Identify Areas to Improve Genetic Test Processes in the University of Maryland Translational Pharmacogenomics Project.

Science.gov (United States)

Cutting, Elizabeth M; Overby, Casey L; Banchero, Meghan; Pollin, Toni; Kelemen, Mark; Shuldiner, Alan R; Beitelshees, Amber L

Delivering genetic test results to clinicians is a complex process. It involves many actors and multiple steps, requiring all of these to work together in order to create an optimal course of treatment for the patient. We used information gained from focus groups in order to illustrate the current process of delivering genetic test results to clinicians. We propose a business process model and notation (BPMN) representation of this process for a Translational Pharmacogenomics Project being implemented at the University of Maryland Medical Center, so that personalized medicine program implementers can identify areas to improve genetic testing processes. We found that the current process could be improved to reduce input errors, better inform and notify clinicians about the implications of certain genetic tests, and make results more easily understood. We demonstrate our use of BPMN to improve this important clinical process for CYP2C19 genetic testing in patients undergoing invasive treatment of coronary heart disease.

Influence of additives on the stability of the phases of alumina

International Nuclear Information System (INIS)

Rosario, D.C.C.; Gouvea, D.

2011-01-01

Problems with the stability of gamma alumina in catalytic reactions have been solved with the inclusion of additives during the synthesis of alumina. These additives stabilize the temperature of phase transition allowing the use of metastable alumina at high temperatures, but the mechanisms of action of additives are not well defined. It is known that each family of additive or additives behaves in different ways for this stabilization. This work aimed to study the performance of MgO and ZrO 2 , respectively at different concentrations in alumina synthesized via Pechini. The samples were analyzed by DSC, X-ray diffraction, measurement of specific surface area by BET analysis, and infrared analysis. The results showed an increase in transition temperature for both additives, and a different changes for specific surface area, showing that MgO and ZrO 2 work on improving the stability but with distinct mechanisms. (author)

Use of rare earth oxides as tracers to identify sediment source areas for agricultural hillslopes

Directory of Open Access Journals (Sweden)

C. Deasy

2010-11-01

Full Text Available Understanding sediment sources is essential to enable more effective targeting of in-field mitigation approaches to reduce diffuse pollution from agricultural land. In this paper we report on the application of rare earth element oxides to arable soils at hillslope scale in order to determine sediment source areas and their relative importance, using a non-intrusive method of surface spraying. Runoff, sediments and rare earth elements lost from four arable hillslope lengths at a site in the UK with clay soils were monitored from three rainfall events after tracer application. Measured erosion rates were low, reflecting the typical event conditions occurring at the site, and less than 1% of the applied REO tracers were recovered, which is consistent with the results of comparable studies. Tracer recovery at the base of the hillslope was able to indicate the relative importance of different hillslope sediment source areas, which were found to be consistent between events. The principal source of eroded sediments was the upslope area, implying that the wheel tracks were principally conduits for sediment transport, and not highly active sites of erosion. Mitigation treatments for sediment losses from arable hillslopes should therefore focus on methodologies for trapping mobile sediments within wheel track areas through increasing surface roughness or reducing the connectivity of sediment transport processes.

Biocompatibility of photopolymers for additive manufacturing

Directory of Open Access Journals (Sweden)

Leonhardt Stefan

2016-09-01

Full Text Available To establish photopolymers for the production of class II or class III medical products by additive manufacturing it is essential to know which components of photopolymeric systems, consisting of monomers, photoinitiators and additives, are the determining factors on their biocompatible properties. In this study the leachable substances of a cured photopolymeric system were eluted and identified by HPLC-MS detection. In addition the cured photopolymer was testes for cytotoxicity and genotoxicity according to DIN EN ISO 10993 for long time applications. The results showed that uncured residual monomers are the determining factor on the biocompatible properties of the photopolymeric system. Strategies to reduce these residual monomers in the cured photopolymer are presented.

Application of spatial methods to identify areas with lime requirement in eastern Croatia

Science.gov (United States)

Bogunović, Igor; Kisic, Ivica; Mesic, Milan; Zgorelec, Zeljka; Percin, Aleksandra; Pereira, Paulo

2016-04-01

With more than 50% of acid soils in all agricultural land in Croatia, soil acidity is recognized as a big problem. Low soil pH leads to a series of negative phenomena in plant production and therefore as a compulsory measure for reclamation of acid soils is liming, recommended on the base of soil analysis. The need for liming is often erroneously determined only on the basis of the soil pH, because the determination of cation exchange capacity, the hydrolytic acidity and base saturation is a major cost to producers. Therefore, in Croatia, as well as some other countries, the amount of liming material needed to ameliorate acid soils is calculated by considering their hydrolytic acidity. For this research, several interpolation methods were tested to identify the best spatial predictor of hidrolitic acidity. The purpose of this study was to: test several interpolation methods to identify the best spatial predictor of hidrolitic acidity; and to determine the possibility of using multivariate geostatistics in order to reduce the number of needed samples for determination the hydrolytic acidity, all with an aim that the accuracy of the spatial distribution of liming requirement is not significantly reduced. Soil pH (in KCl) and hydrolytic acidity (Y1) is determined in the 1004 samples (from 0-30 cm) randomized collected in agricultural fields near Orahovica in eastern Croatia. This study tested 14 univariate interpolation models (part of ArcGIS software package) in order to provide most accurate spatial map of hydrolytic acidity on a base of: all samples (Y1 100%), and the datasets with 15% (Y1 85%), 30% (Y1 70%) and 50% fewer samples (Y1 50%). Parallel to univariate interpolation methods, the precision of the spatial distribution of the Y1 was tested by the co-kriging method with exchangeable acidity (pH in KCl) as a covariate. The soils at studied area had an average pH (KCl) 4,81, while the average Y1 10,52 cmol+ kg-1. These data suggest that liming is necessary

Sintering of manganese ore in natura with different additions on activated carbon

International Nuclear Information System (INIS)

Lima, M.M.F.; Mapa, T.F.M.; Lima, R.M.F.

2016-01-01

Full text: The shortage of high grade manganese ore and the importance of economically viable processes suggest a necessity of the recovery of ore residues. So, this work presents a route to obtain by-products of economic interest from manganese ore residues in bench scale. The objective was the sintering of manganese ore in natura using a particle size below 0,037μm with different additions of activated carbon. For this, the fine residues were calcined at 800°C during 60 minutes, homogenized in an agate mortar with 12% humidity and additions of 9 and 12% of activated carbon. After homogenization, the sintering process was carried out at 1145°C and 1155°C during 5, 15 and 30 minutes at natural air. The products sintered were characterized by bulk density, BET surface area, OM, SEM / EDS and diffraction X-rays. During the calcination of the ore, the mass loss was (15.16 ± 0.02)% due to the elimination of volatiles and water. The surface area of the ore was reduced due to the diffusion process that occurred during sintering. While, the bulk density values had little variation, around (3.51 ± 0.06)g/cm³. The analyses of micro-regions EDS showed that the matrix is a silicate with a high Mn content. It was identified yet, other silicates with different proportions of Si, Al, Ti, Na, Mn, Mg and Ca. (author)

Sintering of manganese ore in natura with different additions on activated carbon

Energy Technology Data Exchange (ETDEWEB)

Lima, M.M.F.; Mapa, T.F.M.; Lima, R.M.F. [Universidade Federal de Ouro Preto (UFOP), MG (Brazil)

2016-07-01

Full text: The shortage of high grade manganese ore and the importance of economically viable processes suggest a necessity of the recovery of ore residues. So, this work presents a route to obtain by-products of economic interest from manganese ore residues in bench scale. The objective was the sintering of manganese ore in natura using a particle size below 0,037μm with different additions of activated carbon. For this, the fine residues were calcined at 800°C during 60 minutes, homogenized in an agate mortar with 12% humidity and additions of 9 and 12% of activated carbon. After homogenization, the sintering process was carried out at 1145°C and 1155°C during 5, 15 and 30 minutes at natural air. The products sintered were characterized by bulk density, BET surface area, OM, SEM / EDS and diffraction X-rays. During the calcination of the ore, the mass loss was (15.16 ± 0.02)% due to the elimination of volatiles and water. The surface area of the ore was reduced due to the diffusion process that occurred during sintering. While, the bulk density values had little variation, around (3.51 ± 0.06)g/cm³. The analyses of micro-regions EDS showed that the matrix is a silicate with a high Mn content. It was identified yet, other silicates with different proportions of Si, Al, Ti, Na, Mn, Mg and Ca. (author)

Infrared Preheating to Enhance Interlayer Strength of Components Printed on the Big Area Additive Manufacturing (BAAM) System

Energy Technology Data Exchange (ETDEWEB)

Kishore, Vidya [ORNL; Ajinjeru, Christine [ORNL; Duty, Chad E [ORNL; Nycz, Andrzej [ORNL; Post, Brian K [ORNL; Lindahl, John M [ORNL; Kunc, Vlastimil [ORNL

2017-01-01

The Big Area Additive Manufacturing (BAAM) system has the capacity to print structures on the order of several meters at a rate exceeding 50 kg/h, thereby having the potential to significantly impact the production of components in automotive, aerospace and energy sectors. However, a primary issue that limits the functional use of such parts is mechanical anisotropy. The strength of printed parts across successive layers in the build direction (z-direction) is significantly lower than the corresponding in-plane strength (x-y directions). This is largely due to poor bonding between the printed layers as the lower layers cool below the glass transition temperature (Tg) before the next layer is deposited. This work explores the use of infrared heating to increase the surface temperature of the printed layer just prior to deposition of new material to improve the interlayer strength of the components. The material used in this study was acrylonitrile butadiene styrene (ABS) reinforced with 20% chopped carbon fiber by weight. Significant improvements in z-strength were observed for the parts whose surface temperature was increased from below Tg to close to or above Tg using infrared heating. Parameters such as print speed, nozzle diameter and extrusion temperature were also found to impact the heat input required to enhance interlayer adhesion without significantly degrading the polymer and compromising on surface finish.

Terminal addition in a cellular world.

Science.gov (United States)

Torday, J S; Miller, William B

2018-07-01

Recent advances in our understanding of evolutionary development permit a reframed appraisal of Terminal Addition as a continuous historical process of cellular-environmental complementarity. Within this frame of reference, evolutionary terminal additions can be identified as environmental induction of episodic adjustments to cell-cell signaling patterns that yield the cellular-molecular pathways that lead to differing developmental forms. Phenotypes derive, thereby, through cellular mutualistic/competitive niche constructions in reciprocating responsiveness to environmental stresses and epigenetic impacts. In such terms, Terminal Addition flows according to a logic of cellular needs confronting environmental challenges over space-time. A reconciliation of evolutionary development and Terminal Addition can be achieved through a combined focus on cell-cell signaling, molecular phylogenies and a broader understanding of epigenetic phenomena among eukaryotic organisms. When understood in this manner, Terminal Addition has an important role in evolutionary development, and chronic disease might be considered as a form of 'reverse evolution' of the self-same processes. Copyright © 2017. Published by Elsevier Ltd.

NASA OSMA NDE Program Additive Manufacturing Foundational Effort

Science.gov (United States)

Waller, Jess; Walker, James; Burke, Eric; Wells, Douglas; Nichols, Charles

2016-01-01

NASA is providing key leadership in an international effort linking NASA and non-NASA resources to speed adoption of additive manufacturing (AM) to meet NASA's mission goals. Participants include industry, NASA's space partners, other government agencies, standards organizations and academia. Nondestructive Evaluation (NDE) is identified as a universal need for all aspects of additive manufacturing.

A GIS methodology to identify potential corn stover collection locations

Energy Technology Data Exchange (ETDEWEB)

Haddad, Monica A. [Department of Community and Regional Planning, 583 College of Design, Iowa State University, Ames, IA 50011-3095 (United States); Anderson, Paul F. [Department of Landscape Architecture, 481 College of Design, Iowa State University, Ames, IA 50011 (United States); Department of Agronomy, 481 College of Design, Iowa State University, Ames, IA 50011 (United States)

2008-12-15

In this study, we use geographic information systems technology to identify potential locations in a Midwestern region for collection and storage of corn stover for use as biomass feedstock. Spatial location models are developed to identify potential collection sites along an existing railroad. Site suitability analysis is developed based on two main models: agronomic productivity potential and environmental costs. The analysis includes the following steps: (1) elaboration of site selection criteria; (2) identification of the study region and service area based on transportation network analysis; (3) reclassification of input spatial layers based on common scales; (4) overlaying the reclassified spatial layers with equal weights to generate the two main models; and (5) overlaying the main models using different weights. A pluralistic approach is adopted, presenting three different scenarios as alternatives for the potential locations. Our results suggest that there is a significant subset of potential sites that meet site selection criteria. Additional studies are needed to evaluate potential sites through field visits, assess economic and social costs, and estimate the proportion of corn producers willing to sell and transport corn stover to collection facilities. (author)

Non-additive measures theory and applications

CERN Document Server

Narukawa, Yasuo; Sugeno, Michio; 9th International Conference on Modeling Decisions for Artificial Intelligence (MDAI 2012)

2014-01-01

This book provides a comprehensive and timely report in the area of non-additive measures and integrals. It is based on a panel session on fuzzy measures, fuzzy integrals and aggregation operators held during the 9th International Conference on Modeling Decisions for Artificial Intelligence (MDAI 2012) in Girona, Spain, November 21-23, 2012. The book complements the MDAI 2012 proceedings book, published in Lecture Notes in Computer Science (LNCS) in 2012. The individual chapters, written by key researchers in the field, cover fundamental concepts and important definitions (e.g. the Sugeno integral, definition of entropy for non-additive measures) as well some important applications (e.g. to economics and game theory) of non-additive measures and integrals. The book addresses students, researchers and practitioners working at the forefront of their field.  

Identifying Effective Strategies for Climate Change Education: The Coastal Areas Climate Change Education (CACCE) Partnership Audiences and Activities

Science.gov (United States)

Ryan, J. G.; Feldman, A.; Muller-Karger, F. E.; Gilbes, F.; Stone, D.; Plank, L.; Reynolds, C. J.

2011-12-01

Many past educational initiatives focused on global climate change have foundered on public skepticism and disbelief. Some key reasons for these past failures can be drawn directly from recognized best practices in STEM education - specifically, the necessity to help learners connect new knowledge with their own experiences and perspectives, and the need to create linkages with issues or concerns that are both important for and relevant to the audiences to be educated. The Coastal Areas Climate Change Education (CACCE) partnership has sought to follow these tenets as guiding principles in identifying critical audiences and developing new strategies for educating the public living in the low-lying coastal areas of Florida and the Caribbean on the realities, risks, and adaptation and mitigation strategies for dealing with the regional impacts of global climate change. CACCE is currently focused on three key learner audiences: a) The formal education spectrum, targeting K-12 curricula through middle school marine science courses, and student and educator audiences through coursework and participatory research strategies engaging participants in a range of climate-related investigations. b) Informal science educators and outlets, in particular aquaria and nature centers, as an avenue toward K-12 teacher professional development as well as for public education. c) Regional planning, regulatory and business professionals focused on the built environment along the coasts, many of whom require continuing education to maintain licensing and/or other professional certifications. Our current activities are focused on bringing together an effective set of educational, public- and private-sector partners to target the varied needs of these audiences in Florida and the U.S. Caribbean, and tailoring an educational plan aimed at these stakeholder audiences that starts with the regionally and topically relevant impacts of climate change, and strategies for effective adaptation and

The estimated additional costs for combustion of agro fuel and the potential of farmers to influence fuel quality; Identifiering av energiverkens merkostnader vid foerbraenning av aakerbraenslen samt lantbrukarens moejlighet att paaverka braenslekvaliteten

Energy Technology Data Exchange (ETDEWEB)

Myringer, Aase; Petersen, Martin; Olsson, Johanna; Roennbaeck, Marie; Bubholz, Monika; Forsberg, Maya

2009-05-15

The main objectives of this study were to identify and calculate the additional costs to energy plants of combustion of agro fuels instead of wood chips, and to determine the potential farmers have to influence fuel quality and thus identify parameters that could be used for pricing in the future. The overall aim is to increase the volume of agro fuels produced. Four agro fuels were considered in this study: willow, straw, husks and reed canary grass. These four were selected because data were available on their combustion at energy plants and because they are representative of different categories of agro fuels: short rotation coppice, crop by-products, seeds and grass. Data were obtained through literature surveys, telephone interviews with farmers, researchers, advisors and contractors, and visits to six energy plants. Combustion properties for each crop and data on combustion were compared. Measures that could be taken by farmers to improve fuel quality today and perhaps in the future were estimated. Although information and experience proved to be lacking in this area, it was possible to identify some potential measures, which are listed below for each fuel. To promote expansion of the agro fuel market, issues concerning business contacts and forms of organisation were examined. The choices and preferences of farmers as regards sale and delivery are influenced by a number of different factors, which were investigated here by studies of the literature and interviews with farmers. There was little documentary evidence available on combustion of agro fuels. Short-term trials have been carried out on small amounts of a number of crop species without specific documentation of emissions, maintenance costs, ash handling, etc. The additional costs to energy plants for combustion of agro fuels compared with wood chips were investigated on visits to energy plants by collecting data directly and by interviewing plant personnel. The additional costs were then calculated

Additional Security Considerations for Grid Management

Science.gov (United States)

Eidson, Thomas M.

2003-01-01

The use of Grid computing environments is growing in popularity. A Grid computing environment is primarily a wide area network that encompasses multiple local area networks, where some of the local area networks are managed by different organizations. A Grid computing environment also includes common interfaces for distributed computing software so that the heterogeneous set of machines that make up the Grid can be used more easily. The other key feature of a Grid is that the distributed computing software includes appropriate security technology. The focus of most Grid software is on the security involved with application execution, file transfers, and other remote computing procedures. However, there are other important security issues related to the management of a Grid and the users who use that Grid. This note discusses these additional security issues and makes several suggestions as how they can be managed.

Using the theory of planned behaviour and self-identity to explain chlamydia testing intentions in young people living in deprived areas.

Science.gov (United States)

Booth, Amy R; Norman, Paul; Harris, Peter R; Goyder, Elizabeth

2014-02-01

The study sought to (1) explain intentions to get tested for chlamydia regularly in a group of young people living in deprived areas using the theory of planned behaviour (TPB); and (2) test whether self-identity explained additional variance in testing intentions. A cross-sectional design was used for this study. Participants (N = 278, 53% male; M = 17.05 years) living in deprived areas of a UK city were recruited from a vocational education setting. Participants completed a self-administered questionnaire, including measures of attitude, injunctive subjective norm, descriptive norm, perceived behavioural control, self-identity, intention and past behaviour in relation to getting tested for chlamydia regularly. The TPB explained 43% of the variance in chlamydia testing intentions with all variables emerging as significant predictors. However, self-identity explained additional variance in intentions (ΔR(2)  = .22) and emerged as the strongest predictor, even when controlling for past behaviour. The study identified the key determinants of intention to get tested for chlamydia regularly in a sample of young people living in areas of increased deprivation: a hard-to-reach, high-risk population. The findings indicate the key variables to target in interventions to promote motivation to get tested for chlamydia regularly in equivalent samples, amongst which self-identity is critical. What is already known on this subject? Young people living in deprived areas have been identified as an at-risk group for chlamydia. Qualitative research has identified several themes in relation to factors affecting the uptake of chlamydia testing, which fit well with the constructs of the Theory of Planned Behaviour (TPB). Identity concerns have also been identified as playing an important part in young people's chlamydia testing decisions. What does this study add? TPB explained 43% of the variance in chlamydia testing intentions and all variables were significant predictors

Public health assessment for petitioned public health assessment, Ottawa Radiation Areas, Ottawa, Lasalle County, Illinois, Region 5. CERCLIS No. ILD980606750. Final report

International Nuclear Information System (INIS)

1993-01-01

During an aerial survey for radiation levels following the cleanup of a radium dial painting operation, abnormally high levels of gamma radiation were detected at thirteen locations throughout Ottawa, Illinois. Additional ground level measurements helped to localize these and four additional areas within the city with levels of radioactivity elevated above background. Field studies by the U.S. Environmental Protection Agency (EPA) and the Illinois Department of Nuclear Safety have identified the major contaminant at these areas as radium-226 (Ra-226). Additional studies to determine the levels of radon-222 (Rn-222) within many structures have indicated radon concentrations well above the EPA limit of 4 picocuries per liter (pCi/L)

76 FR 26279 - Procurement List; Proposed Additions

Science.gov (United States)

2011-05-06

...-service area; clean and sanitize food service equipment, utensil cleaning, and dishwashing; clean pots... additions to the Procurement List. SUMMARY: The Committee is proposing to add services to the Procurement... in this notice will be required to procure the services listed below from nonprofit agencies...

Maternal and child health care in an underprivileged area of Bangalore city: Identifying the gaps in the continuum of care

Directory of Open Access Journals (Sweden)

Avita R Johnson

2015-01-01

Full Text Available Background With over 100 million Indians living in urban slums and high child mortality among low-income groups, focusing on maternal and child health (MCH among urban underprivileged is vital, if India is to achieve the fourth and fifth Millennium Development goals. Objectives To identify the gaps in the MCH Continuum of care, by assessing coverage and quality of Maternal and Child Health Services in an urban underprivileged area of Bangalore City. Methods A survey was conducted in an urban slum of Bangalore City, using systematic random sampling. A total of 178 subjects were interviewed with a pre-tested questionnaire. 88 were mothers who delivered in the last one year (to assess maternal care services, and 90 were mothers of a child aged 12-23 months (to assess immunization coverage. Breastfeeding practices and care during childhood illness were documented in both groups. Results Though institutional delivery rate was 97.7%, only 34.1% mothers had received full antenatal care. The quality of antenatal and postnatal services was poor, practices like prelacteal feeds and delayed initiation of breastfeeding were common. Less than 40 % of children were exclusively breastfed for at least 6 months. Only 53% of children aged 12-23 months were fully immunised. Primary immunisation drop-out rates were high. Mothers’ knowledge regarding vaccines was poor. Children with diarrhea received less fluids and food and only 61% received ORS. Conclusion This study identified the following gaps in the MCH Continuum of Care- lack of IFA consumption, poor quality of antenatal and postnatal care, high immunisation dropout rates, erroneous breastfeeding practices and inadequate care during diarrhoea. Further research may identify potential solutions to bridging these gaps in MCH care.

Maternal and child health care in an underprivileged area of Bangalore city: Identifying the gaps in the continuum of care

Directory of Open Access Journals (Sweden)

Avita R Johnson

2015-10-01

Full Text Available Background With over 100 million Indians living in urban slums and high child mortality among low-­‐income groups, focusing on maternal and child health (MCH among urban underprivileged is vital, if India is to achieve the fourth and fifth Millennium Development goals. Objectives To identify the gaps in the MCH Continuum of care, by assessing coverage and quality of Maternal and Child Health Services in an urban underprivileged area of Bangalore City. Methods A survey was conducted in an urban slum of Bangalore City, using systematic random sampling. A total of 178 subjects were interviewed with a pre-­‐tested questionnaire. 88 were mothers who delivered in the last one year (to assess maternal care services, and 90 were mothers of a child aged 12-­‐23 months (to assess immunization coverage. Breastfeeding practices and care during childhood illness were documented in both groups. Results Though institutional delivery rate was 97.7%, only 34.1% mothers had received full antenatal care. The quality of antenatal and postnatal services was poor, practices like prelacteal feeds and delayed initiation of breastfeeding were common. Less than 40 % of children were exclusively breastfed for at least 6 months. Only 53% of children aged 12-­‐23 months were fully immunised. Primary immunisation drop-­‐out rates were high. Mothers’ knowledge regarding vaccines was poor. Children with diarrhea received less fluids and food and only 61% received ORS. Conclusion This study identified the following gaps in the MCH Continuum of Care-­‐ lack of IFA consumption, poor quality of antenatal and postnatal care, high immunisation dropout rates, erroneous breastfeeding practices and inadequate care during diarrhoea. Further research may identify potential solutions to bridging these gaps in MCH care.

Choking under Pressure: When an Additional Positive Stereotype Affects Performance for Domain Identified Male Mathematics Students

Science.gov (United States)

Rosenthal, Harriet E. S.; Crisp, Richard J.

2007-01-01

This research aimed to establish if the presentation of two positive stereotypes would result in choking under pressure for identified male mathematics students. Seventy-five 16 year old men, who had just commenced their AS-level study, were either made aware of their gender group membership (single positive stereotype), their school group…

Protocol for ADDITION-PRO

DEFF Research Database (Denmark)

Johansen, Nanna Borup; Hansen, Anne-Louise Smidt; Jensen, Troels M

2012-01-01

disease and microvascular diabetic complications. We also require a better understanding of the mechanisms that underlie and drive early changes in cardiometabolic physiology. The ADDITION-PRO study was designed to address these issues among individuals at different levels of diabetes risk recruited from...... Danish primary care. METHODS/DESIGN: ADDITION-PRO is a population-based, longitudinal cohort study of individuals at high risk for diabetes. 16,136 eligible individuals were identified at high risk following participation in a stepwise screening programme in Danish general practice between 2001 and 2006....... All individuals with impaired glucose regulation at screening, those who developed diabetes following screening, and a random sub-sample of those at lower levels of diabetes risk were invited to attend a follow-up health assessment in 2009-2011 (n=4,188), of whom 2,082 (50%) attended. The health...

Categorical and continuous - disentangling the neural correlates of the carry effect in multi-digit addition

Directory of Open Access Journals (Sweden)

Dressel Katharina

2010-11-01

Full Text Available Abstract Background Recently it was suggested that the carry effect observed in addition involves both categorical and continuous processing characteristics. Methods In the present study, we aimed at identifying the specific neural correlates associated with processing either categorical or continuous aspects of the carry effect in an fMRI study on multi-digit addition. Results In line with our expectations, we observed two distinct parts of the fronto-parietal network subserving numerical cognition to be associated with either one of these two characteristics. On the one hand, the categorical aspect of the carry effect was associated with left-hemispheric language areas and the basal ganglia probably reflecting increased demands on procedural and problem solving processes. Complementarily, the continuous aspect of the carry effect was associated with increased intraparietal activation indicating increasing demands on magnitude processing as well as place-value integration with increasing unit sum. Conclusions In summary, the findings suggest representations and processes underlying the carry effect in multi-digit addition to be more complex and interactive than assumed previously.

Identifying (subsurface) anthropogenic heat sources that influence temperature in the drinking water distribution system

Science.gov (United States)

Agudelo-Vera, Claudia M.; Blokker, Mirjam; de Kater, Henk; Lafort, Rob

2017-09-01

The water temperature in the drinking water distribution system and at customers' taps approaches the surrounding soil temperature at a depth of 1 m. Water temperature is an important determinant of water quality. In the Netherlands drinking water is distributed without additional residual disinfectant and the temperature of drinking water at customers' taps is not allowed to exceed 25 °C. In recent decades, the urban (sub)surface has been getting more occupied by various types of infrastructures, and some of these can be heat sources. Only recently have the anthropogenic sources and their influence on the underground been studied on coarse spatial scales. Little is known about the urban shallow underground heat profile on small spatial scales, of the order of 10 m × 10 m. Routine water quality samples at the tap in urban areas have shown up locations - so-called hotspots - in the city, with relatively high soil temperatures - up to 7 °C warmer - compared to the soil temperatures in the surrounding rural areas. Yet the sources and the locations of these hotspots have not been identified. It is expected that with climate change during a warm summer the soil temperature in the hotspots can be above 25 °C. The objective of this paper is to find a method to identify heat sources and urban characteristics that locally influence the soil temperature. The proposed method combines mapping of urban anthropogenic heat sources, retrospective modelling of the soil temperature, analysis of water temperature measurements at the tap, and extensive soil temperature measurements. This approach provided insight into the typical range of the variation of the urban soil temperature, and it is a first step to identifying areas with potential underground heat stress towards thermal underground management in cities.

An overview of zinc addition for BWR dose rate control

Energy Technology Data Exchange (ETDEWEB)

Marble, W.J. [GE Nuclear Energy, San Jose, CA (United States)

1995-03-01

This paper presents an overview of the BWRs employing feedwater zinc addition to reduce primary system dose rates. It identifies which BWRs are using zinc addition and reviews the mechanical injection and passive addition hardware currently being employed. The impact that zinc has on plant chemistry, including the factor of two to four reduction in reactor water Co-60 concentrations, is discussed. Dose rate results, showing the benefits of implementing zinc on either fresh piping surfaces or on pipes with existing films are reviewed. The advantages of using zinc that is isotopically enhanced by the depletion of the Zn-64 precursor to Zn-65 are identified.

Mycobiota in the processing areas of two different meat products

DEFF Research Database (Denmark)

Sørensen, Louise Marie; Jacobsen, Tomas; Nielsen, Per Væggemose

2008-01-01

processing plants and was in addition found on moulded meat products. Sixteen Penicillium species were identified. The most frequently isolated were P. brevicompactum and the closely related P. bialowiezense, P. solitum, P. palitans, P. fagi and a new, not described species named P. “milanense” (ined......Mould growth is not accepted on most types of North European meat products and is considered as both an economic and aesthetic problem for the producers. In order to determine the mycobiota in processing areas of fermented sausage and liver pâté, filamentous fungi were isolated from air, equipment.......; Frisvad, 2007 personal com.). Isolation of a new species illustrates that the mycobiota in the processing areas of North European meat products has not yet been intensively investigated. Several mycotoxin producing species were isolated; the most prevalent were P. brevicompactum/P. bialowiezense and P...

Environmental impacts of the transportation of radioactive materials in urban areas

International Nuclear Information System (INIS)

Finley, N.C.; Taylor, J.M.; Daniel, S.L.; Ericson, D.M. Jr.

1980-01-01

Radioactive material transport in urban areas is investigated and the specific urban features which influence environmental impacts are addressed. These features include the geographic and demographic make-up, and vehicular population and transportation patterns in the area. Previous efforts have not identified a most important population exposure pathway or group. This assessment examines several pathways and a number of urban specific population groups to evaluate their relative significance. In addition, because different causative events contribute to the overall environmental impacts, this assessment addresses four of these: incident free transport, vehicular accidents, human errors, and sabotage or malevolent acts. Not only does radioactive material transport produce radiological and economic consequences but also it can have social impacts. The objective of this study is to examine both the quantitative environmental impacts of radioactive material transport in urban areas and the more subjective social effects of this process. The social impacts assessment was performed by Battelle Human Affairs Research Centers, Seattle, Washington and their conclusions are only summarized here

White Oak Creek watershed: Melton Valley area Remedial Investigation report, at the Oak Ridge National Laboratory, Oak Ridge, Tennessee: Volume 2, Appendixes A and B

International Nuclear Information System (INIS)

1996-11-01

This document contains Appendixes A ''Source Inventory Information for the Subbasins Evaluated for the White Oak Creek Watershed'' and B ''Human Health Risk Assessment for White Oak Creek / Melton Valley Area'' for the remedial investigation report for the White Oak Creek Watershed and Melton Valley Area. Appendix A identifies the waste types and contaminants for each subbasin in addition to the disposal methods. Appendix B identifies potential human health risks and hazards that may result from contaminants present in the different media within Oak Ridge National Laboratory sites

Expanding protected areas beyond their terrestrial comfort zone: identifying spatial options for river conservation

CSIR Research Space (South Africa)

Nel, JL

2009-08-01

Full Text Available and processes in both new and existing protected areas. Data to address these objectives were collated in a Geographic Information System (GIS) and a conservation planning algorithm was used as a means of integrating the multiple objectives in a spatially...

Analysis of consumer preferences focused on food additives

Directory of Open Access Journals (Sweden)

Dagmar Kozelová

2012-01-01

Full Text Available This paper is aimed to evaluate the role of additives in food production and to identify how these additives are known and used by consumers in their households. The questionnaire technique was used, the research involved 220 respondents. It was found that the respondents are perceptive to adding of additives into food. Cluster analysis confirmed that the majority of respondents is about the incidence of food additives only partially informed, although 87% of respondents knew what the (E letter of additive means. The correct answers for each question depended on the age and education of respondents and were not dependent on gender of respondents. We recommend to enhance public knowledge about nutrition, diet and food composition, functions, benefits and safety of food additives.

Does taxonomic diversity in indicator groups influence their effectiveness in identifying priority areas for species conservation?

DEFF Research Database (Denmark)

Bladt, Jesper Stentoft; Larsen, Frank Wugt; Rahbek, Carsten

2008-01-01

The identification of priority areas for biodiversity conservation is a cornerstone of systematic conservation planning. However, biodiversity, or even the distribution of all species, cannot be directly quantified, due to the inherent complexity of natural systems. Species indicator groups may...... serve as important tools for the identification of priority areas for conservation. Yet, it is unclear which factors make certain indicator groups perform better than others. In this study, using data on the Danish distribution of 847 species of plants, vertebrates and insects, we assessed whether...... the taxonomic diversity in species indicator groups influence their effectiveness in the identification of priority areas for species conservation. We tested whether indicator groups comprising a higher taxonomic diversity (i.e. indicator groups consisting of species from many different taxonomic groups...

Operational Area Environmental Evaluations

Energy Technology Data Exchange (ETDEWEB)

Bailey-White, Brenda Eileen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Nagy, Michael David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wagner, Katrina Marie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Goodman, Thomas Richard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Herring, Allen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Catechis, Christopher S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kinghorn, Aubrianna Nicole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Johnson, Ellie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Barthel, Michael David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Casaus, Benito [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-08-01

The Operational Area Environmental Evaluation update provides a description of activities that have the potential to adversely affect natural and cultural resources, including soil, air, water, biological, ecological, and historical resources. The environmental sensitivity of an area is evaluated and summarized, which may facilitate informed management decisions as to where development may be prohibited, restricted, or subject to additional requirements.

Characterization of hydrology and water quality of Piceance Creek in the Alkali Flat area, Rio Blanco County, Colorado, March 2012

Science.gov (United States)

Thomas, Judith C.

2015-12-07

Previous studies by the U.S. Geological Survey identified Alkali Flat as an area of groundwater upwelling, with increases in concentrations of total dissolved solids, and streamflow loss, but additional study was needed to better characterize these observations. The U.S. Geological Survey, in cooperation with the Bureau of Land Management, White River Field Office, conducted a study to characterize the hydrology and water quality of Piceance Creek in the Alkali Flat area of Rio Blanco County, Colorado.

Savannah River Site plan for performing maintenance in Federal Facility Agreement areas (O and M Plan)

International Nuclear Information System (INIS)

Morris, D.R.

1996-01-01

The Savannah River Site was placed on the National Priority List (NPL) in December 1989 and became subject to comprehensive remediation in accordance with CERCLA. The FFA, effective August 16, 1993, establishes the requirements for Site investigation and remediation of releases and potential releases of hazardous substances, and interim status corrective action for releases of hazardous wastes or hazardous constituents. It was determined that further direction was needed for the Operating Departments regarding operation and maintenance activities within those areas listed in the FFA. The Plan for Performing Maintenance (O and M Plan) provides this additional direction. Section 4.0 addresses the operation and maintenance activities necessary for continued operation of the facilities in areas identified as RCRA/CERCLA Units or Site Evaluation Areas. Certain types of the O and M activity could be construed as a remedial or removal action. The intent of this Plan is to provide direction for conducting operation and maintenance activities that are not intended to be remedial or removal actions. The Plan identifies the locations of the units and areas, defines intrusive O and M activities, classifies the intrusive activity as either minor or major, and identifies the requirements, approvals, and documentation necessary to perform the activity in a manner that is protective of human health and the environment; and minimizes any potential impact to any future removal and remedial actions

Geophysical survey for proposed borehole 199-K-107A, 100-K Area

International Nuclear Information System (INIS)

Mitchell, T.H.

1994-01-01

The objective of the survey was to locate subsurface obstructions that may affect the drilling of proposed borehole, 199-K-107A, located about 100 ft northwest of the 105 KW Building, 100-K Area. Based upon the results of the survey, possible drill sites within the zone, with the least likelihood of encountering identified obstructions, were identified. The ground-penetrating radar (GPR) system used for this work utilized a 300-megahertz antenna to transmit the electromagnetic (EM) energy into the ground. The transmitted energy is reflected back to a receiving antenna where variations in the return signal are recorded. Common reflectors include natural geologic conditions such as bedding, cementation, moisture, and clay, or man-made objects such as pipes, barrels, foundations, and buried wires. Several isolated anomalies, at various depths, are observed in the data. Additionally, two areas that appear disturbed, with perplexing character, are plotted. Because of the uncertain nature of these two areas, they were avoided when recommending a borehole location. Initially, the proposed borehole was staked at N130/E122. The new proposed borehole location is N139/E176. This location appears free of anomalies and is over 10 ft from interpreted linear anomalies/pipe-like features

Additive Manufacturing of Biomaterials, Tissues, and Organs.

Science.gov (United States)

Zadpoor, Amir A; Malda, Jos

2017-01-01

The introduction of additive manufacturing (AM), often referred to as three-dimensional (3D) printing, has initiated what some believe to be a manufacturing revolution, and has expedited the development of the field of biofabrication. Moreover, recent advances in AM have facilitated further development of patient-specific healthcare solutions. Customization of many healthcare products and services, such as implants, drug delivery devices, medical instruments, prosthetics, and in vitro models, would have been extremely challenging-if not impossible-without AM technologies. The current special issue of the Annals of Biomedical Engineering presents the latest trends in application of AM techniques to healthcare-related areas of research. As a prelude to this special issue, we review here the most important areas of biomedical research and clinical practice that have benefited from recent developments in additive manufacturing techniques. This editorial, therefore, aims to sketch the research landscape within which the other contributions of the special issue can be better understood and positioned. In what follows, we briefly review the application of additive manufacturing techniques in studies addressing biomaterials, (re)generation of tissues and organs, disease models, drug delivery systems, implants, medical instruments, prosthetics, orthotics, and AM objects used for medical visualization and communication.

E-Area Vault Concrete Material Property And Vault Durability/Degradation Projection Recommendations

Energy Technology Data Exchange (ETDEWEB)

Phifer, M. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2014-03-11

Subsequent to the 2008 E-Area Low-Level Waste Facility (ELLWF) Performance Assessment (PA) (WSRC 2008), two additional E-Area vault concrete property testing programs have been conducted (Dixon and Phifer 2010 and SIMCO 2011a) and two additional E-Area vault concrete durability modeling projections have been made (Langton 2009 and SIMCO 2012). All the information/data from these reports has been evaluated and consolidated herein by the Savannah River National Laboratory (SRNL) at the request of Solid Waste Management (SWM) to produce E-Area vault concrete hydraulic and physical property data and vault durability/degradation projection recommendations that are adequately justified for use within associated Special Analyses (SAs) and future PA updates. The Low Activity Waste (LAW) and Intermediate Level (IL) Vaults structural degradation predictions produced by Carey 2006 and Peregoy 2006, respectively, which were used as the basis for the 2008 ELLWF PA, remain valid based upon the results of the E-Area vault concrete durability simulations reported by Langton 2009 and those reported by SIMCO 2012. Therefore revised structural degradation predictions are not required so long as the mean thickness of the closure cap overlying the vaults is no greater than that assumed within Carey 2006 and Peregoy 2006. For the LAW Vault structural degradation prediction (Carey 2006), the mean thickness of the overlying closure cap was taken as nine feet. For the IL Vault structural degradation prediction (Peregoy 2006), the mean thickness of the overlying closure cap was taken as eight feet. The mean closure cap thicknesses as described here for both E-Area Vaults will be included as a key input and assumption (I&A) in the next revision to the closure plan for the ELLWF (Phifer et al. 2009). In addition, it has been identified as new input to the PA model to be assessed in the ongoing update to the new PA Information UDQE (Flach 2013). Once the UDQE is approved, the SWM Key I

E-Area Vault Concrete Material Property And Vault Durability/Degradation Projection Recommendations

International Nuclear Information System (INIS)

Phifer, M. A.

2014-01-01

Subsequent to the 2008 E-Area Low-Level Waste Facility (ELLWF) Performance Assessment (PA) (WSRC 2008), two additional E-Area vault concrete property testing programs have been conducted (Dixon and Phifer 2010 and SIMCO 2011a) and two additional E-Area vault concrete durability modeling projections have been made (Langton 2009 and SIMCO 2012). All the information/data from these reports has been evaluated and consolidated herein by the Savannah River National Laboratory (SRNL) at the request of Solid Waste Management (SWM) to produce E-Area vault concrete hydraulic and physical property data and vault durability/degradation projection recommendations that are adequately justified for use within associated Special Analyses (SAs) and future PA updates. The Low Activity Waste (LAW) and Intermediate Level (IL) Vaults structural degradation predictions produced by Carey 2006 and Peregoy 2006, respectively, which were used as the basis for the 2008 ELLWF PA, remain valid based upon the results of the E-Area vault concrete durability simulations reported by Langton 2009 and those reported by SIMCO 2012. Therefore revised structural degradation predictions are not required so long as the mean thickness of the closure cap overlying the vaults is no greater than that assumed within Carey 2006 and Peregoy 2006. For the LAW Vault structural degradation prediction (Carey 2006), the mean thickness of the overlying closure cap was taken as nine feet. For the IL Vault structural degradation prediction (Peregoy 2006), the mean thickness of the overlying closure cap was taken as eight feet. The mean closure cap thicknesses as described here for both E-Area Vaults will be included as a key input and assumption (I and A) in the next revision to the closure plan for the ELLWF (Phifer et al. 2009). In addition, it has been identified as new input to the PA model to be assessed in the ongoing update to the new PA Information UDQE (Flach 2013). Once the UDQE is approved, the SWM Key I and

CY15 Livermore Computing Focus Areas

Energy Technology Data Exchange (ETDEWEB)

Connell, Tom M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Cupps, Kim C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); D' Hooge, Trent E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fahey, Tim J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fox, Dave M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Futral, Scott W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gary, Mark R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Goldstone, Robin J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hamilton, Pam G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Heer, Todd M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Long, Jeff W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mark, Rich J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Morrone, Chris J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Shoopman, Jerry D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Slavec, Joe A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Smith, David W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Springmeyer, Becky R [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Stearman, Marc D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Watson, Py C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2015-01-20

The LC team undertook a survey of primary Center drivers for CY15. Identified key drivers included enhancing user experience and productivity, pre-exascale platform preparation, process improvement, data-centric computing paradigms and business expansion. The team organized critical supporting efforts into three cross-cutting focus areas; Improving Service Quality; Monitoring, Automation, Delegation and Center Efficiency; and Next Generation Compute and Data Environments In each area the team detailed high level challenges and identified discrete actions to address these issues during the calendar year. Identifying the Center’s primary drivers, issues, and plans is intended to serve as a lens focusing LC personnel, resources, and priorities throughout the year.

Additionality of global benefits and financial additionality in the context of the AIJ negotiations

Energy Technology Data Exchange (ETDEWEB)

Puhl, I.

1996-12-31

The Conference of the Party at their first meeting (COP1) took a decision regarding criteria for joint implementation as indicated in Art. 4.2 (a) of the FCCC which established a pilot phase for activities implemented jointly (AIJ) under the pilot phase. Besides some more technical issues this decision specified that such measures should bring about real, measurable and long-term environmental benefits related to the mitigation of climate change that would not have occurred in the absence of such activities. It also established that the financing of AIJ shall be additional to the financial obligations of developed country parties. These two requirements are called the additionality criteria for AIJ. The first refers to the realness of GHG emission abatement (which means reduction compared to a baseline) whereas the second describes that funds earmarked for AIJ have no other objective (i.e. profit making, export promotion) but to reduce GHG emissions to avoid the free-riding of investors and subsequently developed country parties. The reporting framework as well as the reporting requirements under national programs do not specify further the two types of additionality and even though research focuses on issues like baseline determination there has been no attempt so far to identify approaches which contribute towards defining strict and practicable methods and guidelines to frame additionality criteria. The first FCCC assessment of pilot project reporting revealed that in the reporting of activities, emissions additionality often remained unclear, especially in cases where AIJ was only a portion of an existing or already planned project, and that there is a point about how to account for financial additionality. It subsequently proposed to develop a uniform approach to baseline determination and the assessment of emission (reduction) additionality and financial additionality.

An Application Of Receptor Modeling To Identify Airborne Particulate ...

African Journals Online (AJOL)

An Application Of Receptor Modeling To Identify Airborne Particulate Sources In Lagos, Nigeria. FS Olise, OK Owoade, HB Olaniyi. Abstract. There have been no clear demarcations between industrial and residential areas of Lagos with focus on industry as the major source. There is need to identify potential source types in ...

Identifying high dose activities in industrial site radiography

International Nuclear Information System (INIS)

Heaton, B.

2000-01-01

Although the radiation doses received by industrial radiographers in the UK have progressively fallen over the last few years, with most now receiving less than 1 mSv/y, a few still receive, relative to the rest, much higher doses. As a percentage of all radiographers the number stays surprisingly constant from year to year. This paper describes a survey to identify the work causing these doses and suggest possible solutions. The UK Central Index of Dose Information was interrogated to identify the industrial radiography companies having staff (not necessarily the same person) with doses of greater than 5mSv/y in the last three years for which information was available. This was 15 in total. The people on the staff receiving these doses were identified and a questionnaire sent to the companies concerned requesting information about their work. A general questionnaire about the operation of the company was also included. With the agreement of the company these questionnaires were followed up by a visit to the company to interviews a number of the management and the radiographers if available. Both groups were generally very open about their problems and every discussion had a positive outcome. Several areas of work/reasons for the doses have been identified. These are: pipeline radiography, ultra sound radiographers working on nuclear reactors, complex plant work often with several teams in the area, inability to retreat from the wind out equipment due to height or access problems, site pressure to not follow the best practices and a lack of appreciation when a dose was being received or, alternatively, carelessness. Some o these problem areas are very difficult to resolve. However ways in which the Health and Safety can help influence the doses have been identified together with practical suggestions radiographers could adopt. These will be reported. (author)

Performance ‘S’ Type Savonius Wind Turbine with Variation of Fin Addition on Blade

Science.gov (United States)

Pamungkas, S. F.; Wijayanto, D. S.; Saputro, H.; Widiastuti, I.

2018-01-01

Wind power has been receiving attention as the new energy resource in addressing the ecological problems of burning fossil fuels. Savonius wind rotor is a vertical axis wind turbines (VAWT) which has relatively simple structure and low operating speed. These characteristics make it suitable for areas with low average wind speed as in Indonesia. To identify the performance of Savonius rotor in generating electrical energy, this research experimentally studied the effect of fin addition for the ‘S’ shape of Savonius VAWT. The fin is added to fill the space in the blade in directing the wind flow. This rotor has two turbine blades, a rotor diameter of 1.1 m and rotor height of 1.4 m, used pulley transmission system with 1:4.2 multiplication ratio, and used a generator type PMG 200 W. The research was conducted during dry season by measuring the wind speed in the afternoon. The average wind speed in the area is 2.3 m/s with the maximum of 4.5 m/s. It was found that additional fin significantly increase the ability of Savonius rotor VAWT to generate electrical energy shown by increasing of electrical power. The highest power generated is 13.40 Watt at a wind speed of 4.5 m/s by adding 1 (one) fin in the blade. It increased by 22.71% from the rotor blade with no additional fin. However, increasing number of fins in the blade was not linearly increase the electrical power generated. The wind rotor blade with 4 additional fins is indicated has the lowest performance, generating only 10.80 Watt electrical power, accounted lower than the one generated by no fin-rotor blade. By knowing the effect of the rotor shape, the rotor dimension, the addition of fin, transmission, and generator used, it is possible to determine alternative geometry design in increasing the electrical power generated by Savonius wind turbine.

Dual Orlicz geominimal surface area

Directory of Open Access Journals (Sweden)

Tongyi Ma

2016-02-01

Full Text Available Abstract The L p $L_{p}$ -geominimal surface area was introduced by Lutwak in 1996, which extended the important concept of the geominimal surface area. Recently, Wang and Qi defined the p-dual geominimal surface area, which belongs to the dual Brunn-Minkowski theory. In this paper, based on the concept of the dual Orlicz mixed volume, we extend the dual geominimal surface area to the Orlicz version and give its properties. In addition, the isoperimetric inequality, a Blaschke-Santaló type inequality, and the monotonicity inequality for the dual Orlicz geominimal surface areas are established.

Measurements of area and the (island) species-area relationship: new directions for an old pattern

DEFF Research Database (Denmark)

Triantis, K.A.; Nogues-Bravo, D.; Hortal, J.

2008-01-01

show that increasing the accuracy of the estimation of area has negligible impact on the fit and form of the species-area relationship, even though our analyses included some of the most topographically diverse island groups in the world. In addition, we show that the inclusion of general measurements...

Vulnerability of particularly valuable areas. Summary

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

This report is part of the scientific basis for the management plan for the North Sea and Skagerrak. The report focuses on the vulnerability of particularly valuable areas to petroleum activities, maritime transport, fisheries, land-based and coastal activities and long-range transboundary pollution. A working group with representatives from many different government agencies, headed by the Institute of Marine Research and the Directorate for Nature Management, has been responsible for drawing up the present report on behalf of the Expert Group for the North Sea and Skagerrak. The present report considers the 12 areas that were identified as particularly valuable during an earlier stage of the management plan process on the environment, natural resources and pollution. There are nine areas along the coast and three open sea areas in the North Sea that were identified according to the same predefined criteria as used for the management plans for the Barents Sea: Lofoten area and the Norwegian Sea. The most important criteria for particularly valuable areas are importance for biological production and importance for biodiversity.(Author)

Vulnerability of particularly valuable areas. Summary

International Nuclear Information System (INIS)

2012-01-01

This report is part of the scientific basis for the management plan for the North Sea and Skagerrak. The report focuses on the vulnerability of particularly valuable areas to petroleum activities, maritime transport, fisheries, land-based and coastal activities and long-range transboundary pollution. A working group with representatives from many different government agencies, headed by the Institute of Marine Research and the Directorate for Nature Management, has been responsible for drawing up the present report on behalf of the Expert Group for the North Sea and Skagerrak. The present report considers the 12 areas that were identified as particularly valuable during an earlier stage of the management plan process on the environment, natural resources and pollution. There are nine areas along the coast and three open sea areas in the North Sea that were identified according to the same predefined criteria as used for the management plans for the Barents Sea: Lofoten area and the Norwegian Sea. The most important criteria for particularly valuable areas are importance for biological production and importance for biodiversity.(Author)

Additive manufacturing of tunable lenses

Science.gov (United States)

Schlichting, Katja; Novak, Tobias; Heinrich, Andreas

2017-02-01

Individual additive manufacturing of optical systems based on 3D Printing offers varied possibilities in design and usage. In addition to the additive manufacturing procedure, the usage of tunable lenses allows further advantages for intelligent optical systems. Our goal is to bring the advantages of additive manufacturing together with the huge potential of tunable lenses. We produced tunable lenses as a bundle without any further processing steps, like polishing. The lenses were designed and directly printed with a 3D Printer as a package. The design contains the membrane as an optical part as well as the mechanical parts of the lens, like the attachments for the sleeves which contain the oil. The dynamic optical lenses were filled with an oil. The focal length of the lenses changes due to a change of the radius of curvature. This change is caused by changing the pressure in the inside of the lens. In addition to that, we designed lenses with special structures to obtain different areas with an individual optical power. We want to discuss the huge potential of this technology for several applications. Further, an appropriate controlling system is needed. Wéll show the possibilities to control and regulate the optical power of the lenses. The lenses could be used for illumination tasks, and in the future, for individual measurement tasks. The main advantage is the individuality and the possibility to create an individual design which completely fulfills the requirements for any specific application.

Identifying areas of high economic-potential copper mineralization using ASTER data in the Urumieh-Dokhtar Volcanic Belt, Iran

Science.gov (United States)

Pour, Amin Beiranvand; Hashim, Mazlan

2012-02-01

This study investigates the application of spectral image processing methods to ASTER data for mapping hydrothermal alteration zones associated with porphyry copper mineralization and related host rock. The study area is located in the southeastern segment of the Urumieh-Dokhtar Volcanic Belt of Iran. This area has been selected because it is a potential zone for exploration of new porphyry copper deposits. Spectral transform approaches, namely principal component analysis, band ratio and minimum noise fraction were used for mapping hydrothermally altered rocks and lithological units at regional scale. Spectral mapping methods, including spectral angle mapper, linear spectral unmixing, matched filtering and mixture tuned matched filtering were applied to differentiate hydrothermal alteration zones associated with porphyry copper mineralization such as phyllic, argillic and propylitic mineral assemblages.Spectral transform methods enhanced hydrothermally altered rocks associated with the known porphyry copper deposits and new identified prospects using shortwave infrared (SWIR) bands of ASTER. These methods showed the discrimination of quartz rich igneous rocks from the magmatic background and the boundary between igneous and sedimentary rocks using the thermal infrared (TIR) bands of ASTER at regional scale. Spectral mapping methods distinguished the sericitically- and argillically-altered rocks (the phyllic and argillic alteration zones) that surrounded by discontinuous to extensive zones of propylitized rocks (the propylitic alteration zone) using SWIR bands of ASTER at both regional and district scales. Linear spectral unmixing method can be best suited for distinguishing specific high economic-potential hydrothermal alteration zone (the phyllic zone) and mineral assemblages using SWIR bands of ASTER. Results have proven to be effective, and in accordance with the results of field surveying, spectral reflectance measurements and X-ray diffraction (XRD) analysis

100 area excavation treatability test plan

International Nuclear Information System (INIS)

1993-05-01

This test plan documents the requirements for a treatability study on field radionuclide analysis and dust control techniques. These systems will be used during remedial actions involving excavation. The data from this treatability study will be used to support the feasibility study (FS) process. Development and screening of remedial alternatives for the 100 Area, using existing data, have been completed and are documented in the 100 Area Feasibility Study, Phases 1 and 2 (DOE-RL 1992a). Based on the results of the FS, the Treatability Study Program Plan (DOE-RL 1992b) identifies and prioritizes treatability studies for the 100 Area. The data from the treatability study program support future focused FS, interim remedial measures (IRM) selection, operable unit final remedy selection, remedial design, and remedial actions. Excavation is one of the high-priority, near-term, treatability study needs identified in the program plan (DOE-RL 1992b). Excavation of contaminated soils and buried solid wastes is included in several of the alternatives identified in the 100 Area FS. Although a common activity, excavation has only been used occasionally at the Hanford Site for waste removal applications

The dilemma of allergy to food additives.

Science.gov (United States)

Bahna, Sami L; Burkhardt, Joshua G

2018-01-01

To provide a brief summary on food additives and to outline a practical approach for evaluating subjects suspected of having reactions to food additives. Information was derived from selected reviews and original articles published in peer-reviewed journals, supplemented by the clinical experience of the authors. Priority was given to studies that used blinded, placebo controlled, oral challenges to confirm adverse reactions to food additives. In addition, selected, appropriately evaluated case reports were included. A large number of food additives are widely used in the food industry. Allergic reactions to additives seem to be rare but are very likely underdiagnosed, primarily due to a low index of suspicion. A wide variety of symptoms to food additives have been reported, but a cause-and-effect relationship has not been well documented in the majority of cases. Reactions to food additives should be suspected in patients who report symptoms related to multiple foods or to a certain food when commercially prepared but not when home made. It is also prudent to investigate food additives in subjects considered to have "idiopathic" reactions. Except for a limited number of natural additives, there is a small role for skin tests or in vitro testing. Oral challenge, in stages, with commonly used additives is the definitive procedure for detecting the offending agent. Once the specific additive is identified, management is strict avoidance, which can be difficult.

Initiatives to Improve Quality of Additively Manufactured Parts

Science.gov (United States)

Waller, Jess; Nichols, Charles

2017-01-01

NASA is providing leadership in an international effort linking government and industry resources to speed adoption of additive manufactured (AM) parts. Participants include government agencies (NASA, USAF, NIST, FAA), industry (commercial aerospace, NDE manufacturers, AM equipment manufacturers), standards organizations and academia. NASA is also partnering with its international space exploration organizations such as ESA and JAXA. NDT is identified as a universal need for all aspects of additive manufacturing.

Etomidate accurately localizes the epileptic area in patients with temporal lobe epilepsy.

Science.gov (United States)

Pastor, Jesús; Wix, Rybel; Meilán, María Luisa; Martínez-Chacón, José Luís; de Dios, Eva; Domínguez-Gadea, Luis; Herrera-Peco, Iván; Sola, Rafael G

2010-04-01

A variety of drugs have been used to activate and identify the epileptogenic area in patients during presurgical evaluation. We have evaluated the safety and usefulness of etomidate in identifying the epileptic zone by measuring bioelectrical brain activity and cerebral blood flow (CBF). We studied 13 men and 9 women under presurgical evaluation for temporal lobe epilepsy. We applied etomidate (0.1 mg/kg) while patients were monitored by video-electroencephalography (VEEG) with foramen ovale electrodes. In a subset of 15 patients, we also measured CBF with single photon emission computed tomography (SPECT). (1) Etomidate induced seizures in 2 of 22 patients. (2) The main side-effects observed were myoclonus (14 of 20) and moderate pain (3 of 20). (3) No changes in capillary oxygen saturation, respiration, or heart rate were observed. (4) Irritative activity specifically increased in the temporal mesial and lateral areas. No spikes were observed in other areas, aside from those observed under baseline conditions. (5) Irritative activity induced by etomidate correctly lateralized the ictal onset zone in 19 of 20 patients. In addition, the two etomidate-induced seizures appeared in the same regions as spontaneous ones. (6) The kinetics of pharmacologically induced activity was higher in the region of the ictal-onset zone. (7) Etomidate increased the CBF in the basal ganglia and especially in the posterior hippocampus of the temporal mesial region contralateral to the ictal-onset zone. Etomidate activation is a safe, specific, and quick test that can be used to identify the epileptic region in patients evaluated as candidates for temporal lobe epilepsy surgery.

Additive Manufacturing of Composites and Complex Materials

Science.gov (United States)

Spowart, Jonathan E.; Gupta, Nikhil; Lehmhus, Dirk

2018-03-01

Advanced composite materials form an important class of high-performance industrial materials used in weight-sensitive applications such as aerospace structures, automotive structures and sports equipment. In many of these applications, parts are made in small production runs, are highly customized and involve long process development times. Developments in additive manufacturing (AM) methods have helped in overcoming many of these limitations. The special topic of Additive Manufacturing of Composites and Complex Materials captures the state of the art in this area by collecting nine papers that present much novel advancement in this field. The studies under this topic show advancement in the area of AM of carbon fiber and graphene-reinforced composites with high thermal and electrical conductivities, development of new hollow glass particle-filled syntactic foam filaments for printing lightweight structures and integration of sensors or actuators during AM of metallic parts. Some of the studies are focused on process optimization or modification to increase the manufacturing speed or tuning manufacturing techniques to enable AM of new materials.

Identifying Areas of Potential Wetland Hydrology in Irrigated Croplands Using Aerial Image Interpretation and Analysis of Rainfall Normality

Science.gov (United States)

2016-06-01

water/saturation, 3) shifts in vegetation , 4) areas of crop stress , and 5) other discolored areas located within the approximate footprint of...of crop/ vegetation stresses . These areas were either lacking vegetation or showed vegetation with a lighter coloration than surrounding vegetation ...for public release ; distribution is unlimited. The U.S. Army Engineer Research and Development Center (ERDC) solves the nation’s toughest

Novel Ways to Identify and Nurture Healthcare Innovation

OpenAIRE

Kurt Hertogs

2015-01-01

Johnson & Johnson is engaged in a new strategy of partnering and cultivating external innovation that relies on strengthening the ecosystem for innovation in its areas of interest. Johnson & Johnson Innovation (JJI) has been implementing this strategy by identifying early innovation and helping to translate it into value added therapeutic solutions and portfolio products. In order to achieve transformational results in areas of high unmet medical need and risk, collaboration with different st...

Catchment areas for public transport

DEFF Research Database (Denmark)

Andersen, Jonas Lohmann Elkjær; Landex, Alex

2008-01-01

In the planning of public transport catchment areas of stops are often included to estimate potential number of travellers. There are different approaches to GIS-based catchment area analyses depending on the desired level of detail. The Circular Buffer approach is the fundamental, but also....../from stations. The article also shows how the refinement of the Service Area approach with additional time resistance results in smaller catchment areas when the feeder routes cross stairs. It is concluded that GIS-based catchment area analyses are a multiple decision support tool for planning of public...... transport where the level of detail can be suited to the purpose....

Tomato farmers adoption level of postharvest value addition ...

African Journals Online (AJOL)

The study examined tomato farmers' adoption level of postharvest value addition technology and its constraints in Surulere Area of Oyo state. 160 tomato farmers were randomly selected and interviewed through structured interview schedule. Data obtained were subjected to descriptive and inferential statistics. Results ...

75 FR 5715 - Identification of Additional Classes of Facilities for Development of Financial Responsibility...

Science.gov (United States)

2010-02-04

... as facilities engaged in the recycling of materials containing CERCLA hazardous substances as... addition, the Agency identified the Waste Management and Remediation Services industry (NAICS 562), the... Liability Act (CERCLA). In addition, the Agency identified the Waste Management and Remediation Services...

The addition of disilanes to cumulenes

Energy Technology Data Exchange (ETDEWEB)

Chen, Yiyuan [Iowa State Univ., Ames, IA (United States)

1997-10-08

The syntheses of silicon-containing compounds and the studies of their rearrangements have been active research areas in the Barton research group. Previously, the addition of disilanes to acetylenes was studied in the group and an intramolecular 2S + 2A mechanism has been proposed. In this thesis, the work is focused on the addition of disilanes to cumulenes. The syntheses of the precursors are discussed and the possible mechanisms for their thermal, photochemical and catalytic rearrangements are proposed. Conjugated organic polymers have been studied in the group since 1985 because of their potential for exhibiting high electroconductivity, photoconductivity, strong non-linear optical response and intense fluorescence. In the second section of this dissertation, the synthesis and property studies of poly(phenylene vinylene) analogues are discussed.

On equilibrium real exchange rates in euro area: Special focus on behavioral equilibrium exchange rates in Ireland and Greece

Directory of Open Access Journals (Sweden)

Klára Plecitá

2012-01-01

Full Text Available This paper focuses on the intra-euro-area imbalances. Therefore the first aim of this paper is to identify euro-area countries exhibiting macroeconomic imbalances. The subsequent aim is to estimate equilibrium real exchange rates for these countries and to compute their degrees of real exchange rate misalignment. The intra-area balance is assessed using the Cluster Analysis and the Principle Component Analysis; on this basis Greece and Ireland are selected as the two euro-area countries with largest imbalances in 2010. Further the medium-run equilibrium exchange rates for Greece and Ireland are estimated applying the Behavioral Equilibrium Exchange Rate (BEER approach popularised by Clark and MacDonald (1998. In addition, the long-run equilibrium exchange rates are estimated using the Permanent Equilibrium Exchange Rate (PEER model. Employing the BEER and PEER approaches on quarterly time series of real effective exchange rates (REER from 1997: Q1 to 2010: Q4 we identify an undervaluation of the Greek and Irish REER around their entrance to the euro area. For the rest of the period analysed their REER is broadly in line with estimated BEER and PEER levels.

Carbon Monoxide Nonattainment Areas

Data.gov (United States)

U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for Carbon Monoxide and have...

SO2 Nonattainment Areas

Data.gov (United States)

U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for Sulfur dioxide and have...

Using Generalized Additive Modeling to Empirically Identify Thresholds within the ITERS in Relation to Toddlers' Cognitive Development

Science.gov (United States)

Setodji, Claude Messan; Le, Vi-Nhuan; Schaack, Diana

2013-01-01

Research linking high-quality child care programs and children's cognitive development has contributed to the growing popularity of child care quality benchmarking efforts such as quality rating and improvement systems (QRIS). Consequently, there has been an increased interest in and a need for approaches to identifying thresholds, or cutpoints,…

Attitude Towards Physics and Additional Mathematics Achievement Towards Physics Achievement

Science.gov (United States)

Veloo, Arsaythamby; Nor, Rahimah; Khalid, Rozalina

2015-01-01

The purpose of this research is to identify the difference in students' attitude towards Physics and Additional Mathematics achievement based on gender and relationship between attitudinal variables towards Physics and Additional Mathematics achievement with achievement in Physics. This research focused on six variables, which is attitude towards…

Reduction of radiation area project plan

International Nuclear Information System (INIS)

1979-08-01

This plan deals with the overall reduction of outdoor surface radiation areas under Rockwell's jurisdiction. Four basic alternatives are identified which will reduce and/or stabilize radiation areas until long-term disposal decisions are made: (1) continued routine surveillance and maintenance; (2) reduction or elimination of effluent discharges; (3) improved site stabilization; and (4) site removal. The four major transport mechanisms at Hanford that are the primary forces for contamination spread are identified as wind, animal transport, concentration and dispersal by plants, and transport resulting from human activities

Entomopathogenic nematodes in agricultural areas in Brazil.

Science.gov (United States)

de Brida, Andressa Lima; Rosa, Juliana Magrinelli Osório; Oliveira, Cláudio Marcelo Gonçalves de; Castro, Bárbara Monteiro de Castro E; Serrão, José Eduardo; Zanuncio, José Cola; Leite, Luis Garrigós; Wilcken, Silvia Renata Siciliano

2017-04-06

Entomopathogenic nematodes (EPNs) (Steinernematidae and Heterorhabditidae) can control pests due to the mutualistic association with bacteria that kill the host by septicemia and make the environment favorable for EPNs development and reproduction. The diversity of EPNs in Brazilian soils requires further study. The identification of EPNs, adapted to environmental and climatic conditions of cultivated areas is important for sustainable pest suppression in integrated management programs in agricultural areas of Brazil. The objective was to identify EPNs isolated from agricultural soils with annual, fruit and forest crops in Brazil. Soil samples were collected and stored in 250 ml glass vials. The nematodes were isolated from these samples with live bait traps ([Galleria mellonella L. (Lepidoptera: Pyralidae) larvae]. Infective juveniles were collected with White traps and identified by DNA barcoding procedures by sequencing the D2/D3 expansion of the 28S rDNA region by PCR. EPNs identified in agricultural areas in Brazil were Heterorhabditis amazonensis, Metarhabditis rainai, Oscheios tipulae and Steinernema rarum. These species should be considered pest biocontrol agents in Brazilian agricultural areas.

77 FR 29596 - Procurement List Proposed Additions

Science.gov (United States)

2012-05-18

.../Location: Laundry Service, Veterans Administration Medical Center (VAMC), (offsite: 1809 W 2nd Avenue... Additions to the Procurement List. SUMMARY: The Committee is proposing to add products and services to the... identified in this notice will be required to procure the products and services listed below from nonprofit...

Science and Technology Business Area Strategic Plan

National Research Council Canada - National Science Library

Paul, Richard

2000-01-01

The S&T Business Area Strategic Plan has been updated to include lessons learned over the last two years, identifies areas that need to be reviewed further, addresses business opportunities and threats...

Broca’s area processes the hierarchical organization of observed action

Directory of Open Access Journals (Sweden)

Masumi eWakita

2014-01-01

Full Text Available Broca’s area has been suggested as the area responsible for the domain-general hierarchical processing of language and music. Although meaningful action shares a common hierarchical structure with language and music, the role of Broca’s area in this domain remains controversial. To address the involvement of Broca’s area in the processing action hierarchy, the activation of Broca’s area was measured using near-infrared spectroscopy. Measurements were taken while participants watched silent movies that featured hand movements playing familiar and unfamiliar melodies. The unfamiliar melodies were reversed versions of the familiar melodies. Additionally, to investigate the effect of a motor experience on the activation of Broca’s area, the participants were divided into well-trained and less-trained groups. The results showed that Broca’s area in the well-trained participants demonstrated a significantly larger activation in response to the hand motion when an unfamiliar melody was played than when a familiar melody was played. However, Broca’s area in the less-trained participants did not show a contrast between conditions despite identical abilities of the two participant groups to identify the melodies by watching key pressing actions. These results are consistent with previous findings that Broca’s area exhibits increased activation in response to grammatically violated sentences and musically deviated chord progressions as well as the finding that this region does not represent the processing of grammatical structure in less-proficient foreign language speakers. Thus, the current study suggests that Broca’s area represents action hierarchy and that sufficiently long motor training is necessary for it to become sensitive to motor syntax. Therefore, the notion that hierarchical processing in Broca’s area is a common function shared between language and music may help to explain the role of Broca’s area in action perception.

Optimal choice: assessing the probability of additional damage to buildings caused by water level changes of larger areas

Science.gov (United States)

Bijnagte, J. L.; Luger, D.

2012-12-01

In the Northern parts of the Netherlands exploration of natural gas reservoirs causes subsidence over large areas. As a consequence, the water levels in canals and polders have to be adjusted over time in order to keep the groundwater levels at a constant depth relative to the surface level. In the middle of the subsidence area it is relatively easy to follow the settlements by a uniform lowering of the water level. This would however result in a relative lowering of the groundwater table at the edges of the subsidence area. Given the presence of soft compressible soils, this would result in induced settlements. For buildings in these areas this will increase the chance of damage. A major design challenge lies therefore in the optimisation of the use of compartments. The more compartments the higher the cost therefore the aim is to make compartments in the water management system that are as large as possible without causing inadmissible damage to buildings. In order to asses expected damage from different use of compartments three tools are needed. The first is a generally accepted method of damage determination, the second a method to determine the contribution to damage of a new influence, e.g. a groundwater table change. Third, and perhaps most importantly, a method is needed to evaluate effects not for single buildings but for larger areas. The first need is covered by established damage criteria like those of Burland & Wroth or Boscardin & Cording. Up until now the second and the third have been problematic. This paper presents a method which enables to assign a contribution to the probability of damage of various recognised mechanisms such as soil and foundation inhomogeneity, uneven loading, ground water level changes. Shallow subsidence due to peat oxidation and deep subsidence due to reservoir depletion can be combined. In order to address the third issue: evaluation of effects for larger areas, the method uses a probabilistic approach. Apart from a

PM 10 Nonattainment Areas

Data.gov (United States)

U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for PM 10 and have been...

Waste Area Grouping 2 Remedial Investigation Phase 1 Seep Task data report: Contaminant source area assessment

International Nuclear Information System (INIS)

Hicks, D.S.

1996-03-01

This report presents the findings of the Waste Area Grouping (WAG) 2, Phase 1 Remedial Investigation (RI) Seep Task efforts during 1993 and 1994 at Oak Ridge National Laboratory (ORNL). The results presented here follow results form the first year of sampling, 1992, which are contained in the Phase 1 RI report for WAG 2 (DOE 1995a). The WAG 2 Seep Task efforts focused on contaminants in seeps, tributaries, and main streams within the White Oak Creek (WOC) watershed. This report is designed primarily as a reference for contaminants and a resource for guiding remedial decisions. Additional in-depth assessments of the Seep Task data may provide clearer understandings of contaminant transport from the different source areas in the WOC watershed. WAG 2 consists of WOC and its tributaries downstream of the ORNL main plant area, White Oak Lake, the White Oak Creek Embayment of the Clinch River, and the associated flood plains and subsurface environment. The WOC watershed encompasses ORNL and associated WAGs. WAG 2 acts as an integrator for contaminant releases from the contaminated sites at ORNL and as the conduit transporting contaminants to the Clinch River. The main objectives of the Seep Task were to identify and characterize seeps, tributaries and source areas that are responsible for the contaminant releases to the main streams in WAG 2 and to quantify their input to the total contaminant release from the watershed at White Oak Dam (WOD). Efforts focused on 90 Sr, 3 H, and 137 Cs because these contaminants pose the greatest potential human health risk from water ingestion at WOD. Bimonthly sampling was conducted throughout the WOC watershed beginning in March 1993 and ending in August 1994. Samples were also collected for metals, anions, alkalinity, organics, and other radionuclides

Identifying sources of emerging organic contaminants in a mixed use watershed using principal components analysis.

Science.gov (United States)

Karpuzcu, M Ekrem; Fairbairn, David; Arnold, William A; Barber, Brian L; Kaufenberg, Elizabeth; Koskinen, William C; Novak, Paige J; Rice, Pamela J; Swackhamer, Deborah L

2014-01-01

Principal components analysis (PCA) was used to identify sources of emerging organic contaminants in the Zumbro River watershed in Southeastern Minnesota. Two main principal components (PCs) were identified, which together explained more than 50% of the variance in the data. Principal Component 1 (PC1) was attributed to urban wastewater-derived sources, including municipal wastewater and residential septic tank effluents, while Principal Component 2 (PC2) was attributed to agricultural sources. The variances of the concentrations of cotinine, DEET and the prescription drugs carbamazepine, erythromycin and sulfamethoxazole were best explained by PC1, while the variances of the concentrations of the agricultural pesticides atrazine, metolachlor and acetochlor were best explained by PC2. Mixed use compounds carbaryl, iprodione and daidzein did not specifically group with either PC1 or PC2. Furthermore, despite the fact that caffeine and acetaminophen have been historically associated with human use, they could not be attributed to a single dominant land use category (e.g., urban/residential or agricultural). Contributions from septic systems did not clarify the source for these two compounds, suggesting that additional sources, such as runoff from biosolid-amended soils, may exist. Based on these results, PCA may be a useful way to broadly categorize the sources of new and previously uncharacterized emerging contaminants or may help to clarify transport pathways in a given area. Acetaminophen and caffeine were not ideal markers for urban/residential contamination sources in the study area and may need to be reconsidered as such in other areas as well.

Tiered High-Throughput Screening Approach to Identify ...

Science.gov (United States)

High-throughput screening (HTS) for potential thyroid–disrupting chemicals requires a system of assays to capture multiple molecular-initiating events (MIEs) that converge on perturbed thyroid hormone (TH) homeostasis. Screening for MIEs specific to TH-disrupting pathways is limited in the US EPA ToxCast screening assay portfolio. To fill one critical screening gap, the Amplex UltraRed-thyroperoxidase (AUR-TPO) assay was developed to identify chemicals that inhibit TPO, as decreased TPO activity reduces TH synthesis. The ToxCast Phase I and II chemical libraries, comprised of 1,074 unique chemicals, were initially screened using a single, high concentration to identify potential TPO inhibitors. Chemicals positive in the single concentration screen were retested in concentration-response. Due to high false positive rates typically observed with loss-of-signal assays such as AUR-TPO, we also employed two additional assays in parallel to identify possible sources of nonspecific assay signal loss, enabling stratification of roughly 300 putative TPO inhibitors based upon selective AUR-TPO activity. A cell-free luciferase inhibition assay was used to identify nonspecific enzyme inhibition among the putative TPO inhibitors, and a cytotoxicity assay using a human cell line was used to estimate the cellular tolerance limit. Additionally, the TPO inhibition activities of 150 chemicals were compared between the AUR-TPO and an orthogonal peroxidase oxidation assay using

Ecosystem studies, endangered species survey - Gibson Dome and Elk Ridge study areas, Paradox Basin, Utah

International Nuclear Information System (INIS)

1983-04-01

This report is published as a product of the National Waste Terminal Storage (NWTS) Program. The objective of this program is the development of terminal waste storage facilities in deep stable geologic formations for high-level nuclear wastes, including spent fuel elements from commercial power reactors and transuranic nuclear waste for which the federal government is responsible. This report is part of the location and site characterization phase and contains threatened and endangered species information for the Gibson Dome and Elk Ridge study areas of the Paradox Region. The threatened and endangered species information was obtained through site surveys designed and implemented by area experts. The site surveys were performed during the period late summer 1981 - spring 1982 in the Gibson Dome and Elk Ridge Study Areas. No threatened or endangered species were identified in either Lavender or Davis canyons. Additional studies at the borehole locations in Beef Basin did identify the nearest occurrence of a species proposed for endangered status (Astragalus monumentalis, a monument milkvetch, member of the legume family). The species was identified approximately 160 to 300 m (500 to 1000 ft) from a hydro testing drill site. Consequently, construction and operation activity should not cause any adverse impacts. This report will be used to satisfy Section 7 requirements of the Endangered Species Act (PL 93-205 as amended) and to allow the United States Fish and Wildlife Service to verify that no protected species are subject to disturbance as the result of project activities occurring in the Gibson Dome and Elk Ridge study areas

Do reading additions improve reading in pre-presbyopes with low vision?

Science.gov (United States)

Alabdulkader, Balsam; Leat, Susan

2012-09-01

This study compared three different methods of determining a reading addition and the possible improvement on reading performance in children and young adults with low vision. Twenty-eight participants with low vision, aged 8 to 32 years, took part in the study. Reading additions were determined with (a) a modified Nott dynamic retinoscopy, (b) a subjective method, and (c) an age-based formula. Reading performance was assessed with MNREAD-style reading charts at 12.5 cm, with and without each reading addition in random order. Outcome measures were reading speed, critical print size, MNREAD threshold, and the area under the reading speed curve. For the whole group, there was no significant improvement in reading performance with any of the additions. When participants with normal accommodation at 12.5 cm were excluded, the area under the reading speed curve was significantly greater with all reading additions compared with no addition (p = 0.031, 0.028, and 0.028, respectively). Also, the reading acuity threshold was significantly better with all reading additions compared with no addition (p = 0.014, 0.030, and 0.036, respectively). Distance and near visual acuity, age, and contrast sensitivity did not predict improvement with a reading addition. All, but one, of the participants who showed a significant improvement in reading with an addition had reduced accommodation. A reading addition may improve reading performance for young people with low vision and should be considered as part of a low vision assessment, particularly when accommodation is reduced.

76 FR 77677 - Establishment of the Coombsville Viticultural Area

Science.gov (United States)

2011-12-14

... Decision. SUMMARY: This final rule establishes the 11,075-acre ``Coombsville'' viticultural area in Napa... describe the origin of their wines and to allow consumers to better identify wines they may purchase. DATES... consumers and helps consumers to identify wines they may purchase. Establishment of a viticultural area is...

General Practice Clinical Data Help Identify Dementia Hotspots: A Novel Geospatial Analysis Approach.

Science.gov (United States)

Bagheri, Nasser; Wangdi, Kinley; Cherbuin, Nicolas; Anstey, Kaarin J

2018-01-01

We have a poor understanding of whether dementia clusters geographically, how this occurs, and how dementia may relate to socio-demographic factors. To shed light on these important questions, this study aimed to compute a dementia risk score for individuals to assess spatial variation of dementia risk, identify significant clusters (hotspots), and explore their association with socioeconomic status. We used clinical records from 16 general practices (468 Statistical Area level 1 s, N = 14,746) from the city of west Adelaide, Australia for the duration of 1 January 2012 to 31 December 2014. Dementia risk was estimated using The Australian National University-Alzheimer's Disease Risk Index. Hotspot analyses were applied to examine potential clusters in dementia risk at small area level. Significant hotspots were observed in eastern and southern areas while coldspots were observed in the western area within the study perimeter. Additionally, significant hotspots were observed in low socio-economic communities. We found dementia risk scores increased with age, sex (female), high cholesterol, no physical activity, living alone (widow, divorced, separated, or never married), and co-morbidities such as diabetes and depression. Similarly, smoking was associated with a lower dementia risk score. The identification of dementia risk clusters may provide insight into possible geographical variations in risk factors for dementia and quantify these risks at the community level. As such, this research may enable policy makers to tailor early prevention strategies to the correct individuals within their precise locations.

Identifying the causes of differences in ozone production from the CB05 and CBMIV chemical mechanisms

Directory of Open Access Journals (Sweden)

R. D. Saylor

2012-02-01

Full Text Available An investigation was conducted to identify the mechanistic differences between two versions of the carbon bond gas-phase chemical mechanism (CB05 and CBMIV which consistently lead to larger ground-level ozone concentrations being produced in the CB05 version of the National Air Quality Forecasting Capability (NAQFC modeling system even though the two parallel forecast systems utilize the same meteorology and base emissions and similar initial and boundary conditions. Box models of each of the mechanisms as they are implemented in the NAQFC were created and a set of 12 sensitivity simulations was designed. The sensitivity simulations independently probed the conceptual mechanistic differences between CB05 and CBMIV and were exercised over a 45-scenario simulation suite designed to emulate the wide range of chemical regimes encountered in a continental-scale atmospheric chemistry model. Results of the sensitivity simulations indicate that two sets of reactions that were included in the CB05 mechanism, but which were absent from the CBMIV mechanism, are the primary causes of the greater ozone production in the CB05 version of the NAQFC. One set of reactions recycles the higher organic peroxide species of CB05 (ROOH, resulting in additional photochemically reactive products that act to produce additional ozone in some chemical regimes. The other set of reactions recycles reactive nitrogen from less reactive forms back to NO₂, increasing the effective NO_x concentration of the system. In particular, the organic nitrate species (NTR, which was a terminal product for reactive nitrogen in the CBMIV mechanism, acts as a reservoir species in CB05 to redistribute NO_x from major source areas to potentially NO_x-sensitive areas where additional ozone may be produced in areas remote from direct NO_x sources.

Versatility of cooperative transcriptional activation: a thermodynamical modeling analysis for greater-than-additive and less-than-additive effects.

Directory of Open Access Journals (Sweden)

Till D Frank

Full Text Available We derive a statistical model of transcriptional activation using equilibrium thermodynamics of chemical reactions. We examine to what extent this statistical model predicts synergy effects of cooperative activation of gene expression. We determine parameter domains in which greater-than-additive and less-than-additive effects are predicted for cooperative regulation by two activators. We show that the statistical approach can be used to identify different causes of synergistic greater-than-additive effects: nonlinearities of the thermostatistical transcriptional machinery and three-body interactions between RNA polymerase and two activators. In particular, our model-based analysis suggests that at low transcription factor concentrations cooperative activation cannot yield synergistic greater-than-additive effects, i.e., DNA transcription can only exhibit less-than-additive effects. Accordingly, transcriptional activity turns from synergistic greater-than-additive responses at relatively high transcription factor concentrations into less-than-additive responses at relatively low concentrations. In addition, two types of re-entrant phenomena are predicted. First, our analysis predicts that under particular circumstances transcriptional activity will feature a sequence of less-than-additive, greater-than-additive, and eventually less-than-additive effects when for fixed activator concentrations the regulatory impact of activators on the binding of RNA polymerase to the promoter increases from weak, to moderate, to strong. Second, for appropriate promoter conditions when activator concentrations are increased then the aforementioned re-entrant sequence of less-than-additive, greater-than-additive, and less-than-additive effects is predicted as well. Finally, our model-based analysis suggests that even for weak activators that individually induce only negligible increases in promoter activity, promoter activity can exhibit greater-than-additive

Complementarity and Area-Efficiency in the Prioritization of the Global Protected Area Network.

Directory of Open Access Journals (Sweden)

Peter Kullberg

Full Text Available Complementarity and cost-efficiency are widely used principles for protected area network design. Despite the wide use and robust theoretical underpinnings, their effects on the performance and patterns of priority areas are rarely studied in detail. Here we compare two approaches for identifying the management priority areas inside the global protected area network: 1 a scoring-based approach, used in recently published analysis and 2 a spatial prioritization method, which accounts for complementarity and area-efficiency. Using the same IUCN species distribution data the complementarity method found an equal-area set of priority areas with double the mean species ranges covered compared to the scoring-based approach. The complementarity set also had 72% more species with full ranges covered, and lacked any coverage only for half of the species compared to the scoring approach. Protected areas in our complementarity-based solution were on average smaller and geographically more scattered. The large difference between the two solutions highlights the need for critical thinking about the selected prioritization method. According to our analysis, accounting for complementarity and area-efficiency can lead to considerable improvements when setting management priorities for the global protected area network.

Complementarity and Area-Efficiency in the Prioritization of the Global Protected Area Network.

Science.gov (United States)

Kullberg, Peter; Toivonen, Tuuli; Montesino Pouzols, Federico; Lehtomäki, Joona; Di Minin, Enrico; Moilanen, Atte

2015-01-01

Complementarity and cost-efficiency are widely used principles for protected area network design. Despite the wide use and robust theoretical underpinnings, their effects on the performance and patterns of priority areas are rarely studied in detail. Here we compare two approaches for identifying the management priority areas inside the global protected area network: 1) a scoring-based approach, used in recently published analysis and 2) a spatial prioritization method, which accounts for complementarity and area-efficiency. Using the same IUCN species distribution data the complementarity method found an equal-area set of priority areas with double the mean species ranges covered compared to the scoring-based approach. The complementarity set also had 72% more species with full ranges covered, and lacked any coverage only for half of the species compared to the scoring approach. Protected areas in our complementarity-based solution were on average smaller and geographically more scattered. The large difference between the two solutions highlights the need for critical thinking about the selected prioritization method. According to our analysis, accounting for complementarity and area-efficiency can lead to considerable improvements when setting management priorities for the global protected area network.

Environmental pollution in Mayo area and its impact on people health

International Nuclear Information System (INIS)

Omer, N. H.

2003-04-01

The study undertook the pollution problem in Mayo area, south of the Green Belt. This is considered to have come about as a result of legal and illegal planning and the re-planning of the squatter settlements, plus the area that lies in the vicinity of the sanitary drainage pool. The study identified the factors and causes of the pollutants.The study also studied the effects of these pollutants on health. The objectives of the study were to identify the factors of environmental pollution in the area, the role of the people in the environmental pollution, the negative consequences of this pollution on people in the area, the attempts of the local authorities in fighting the area's pollution and improving the habitat. The study depended on some scientific approaches such as the historic method and the descriptive statistics method. Information was collected from primary and secondary sources. The researcher depended on field work such as direct observation, personal interviews and filling questionnaire which were prepared for data allocation. The study concluded that the environmental pollution is an out come of many factors that inter link with each other. One of the most important factors is the low economic level of the people, and its effects on the poor and deteriorating living environment and the planning of the area placing it near the sources of environmental pollution at the green belt. In addition to the negative role played by the areas inhabitants in relation to getting rid of environmental pollutants of the area, which has in turn led to the outbreak of environmental diseases that reside in the area, specially malaria and diarrhea. The researcher views that one of the most important recommendations that this study has come out of with is the general planning that takes into consideration the health, economic natural and environmental aspects. These are necessities that will participate in the decline and end of the spreading of these pollutants and what

Can subsyndromal manifestations of major depression be identified in children at risk?

Science.gov (United States)

Uchida, M; Fitzgerald, M; Lin, K; Carrellas, N; Woodworth, H; Biederman, J

2017-02-01

Children of parents with major depression are at significantly increased risk for developing major depression themselves; however, not all children at genetic risk will develop major depressive disorder (MDD). We investigated the utility of subsyndromal scores on the Child Behavior Checklist (CBCL) Anxiety/Depression scale in identifying children at the highest risk for pediatric MDD from among the pool of children of parents with MDD or bipolar disorder. The sample was derived from two previously conducted longitudinal case-control family studies of psychiatrically and pediatrically referred youth and their families. For this study, probands were stratified based on the presence or absence of a parental mood disorder. Subsyndromal scores on the CBCL Anxiety/Depression scale significantly separated the children at high risk for pediatric MDD from those at low risk in a variety of functional areas, including social and academic functioning. Additionally, children at genetic risk without elevated CBCL Anxiety/Depression scale scores were largely indistinguishable from controls. These results suggest that the CBCL Anxiety/Depression scale can help identify children at highest risk for pediatric MDD. If implemented clinically, this scale would cost-effectively screen children and identify those most in need of early intervention resources to impede the progression of depression. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

The development and validation of a two-tiered multiple-choice instrument to identify alternative conceptions in earth science

Science.gov (United States)

Mangione, Katherine Anna

This study was to determine reliability and validity for a two-tiered, multiple- choice instrument designed to identify alternative conceptions in earth science. Additionally, this study sought to identify alternative conceptions in earth science held by preservice teachers, to investigate relationships between self-reported confidence scores and understanding of earth science concepts, and to describe relationships between content knowledge and alternative conceptions and planning instruction in the science classroom. Eighty-seven preservice teachers enrolled in the MAT program participated in this study. Sixty-eight participants were female, twelve were male, and seven chose not to answer. Forty-seven participants were in the elementary certification program, five were in the middle school certification program, and twenty-nine were pursuing secondary certification. Results indicate that the two-tiered, multiple-choice format can be a reliable and valid method for identifying alternative conceptions. Preservice teachers in all certification areas who participated in this study may possess common alternative conceptions previously identified in the literature. Alternative conceptions included: all rivers flow north to south, the shadow of the Earth covers the Moon causing lunar phases, the Sun is always directly overhead at noon, weather can be predicted by animal coverings, and seasons are caused by the Earth's proximity to the Sun. Statistical analyses indicated differences, however not all of them significant, among all subgroups according to gender and certification area. Generally males outperformed females and preservice teachers pursuing middle school certification had higher scores on the questionnaire followed by those obtaining secondary certification. Elementary preservice teachers scored the lowest. Additionally, self-reported scores of confidence in one's answers and understanding of the earth science concept in question were analyzed. There was a

Identifying the tundra-forest border in the stomate record: an analysis of lake surface samples from the Yellowknife area, Northwest Territories, Canada

Energy Technology Data Exchange (ETDEWEB)

Hansen, B.C.S. [Minnesota Univ., Minneapolis, MN (United States). Limnological Research Center; MacDonald, G.M. [California Univ., Los Angeles, CA (United States). Dept. of Botanical Sciences; Moser, K.A. [McMaster Univ., Hamilton, ON (Canada)

1996-05-01

The relationship between conifer stomata and existing vegetation across tundra, forest-tundra, and closed zones in the Yellowknife area of the Northwest Territories was studied. Conifer stomata were identified in surface samples from lakes in the treeline zone, but were absent in samples from tundra lakes. Stomate analysis was recorded and the results were presented in a concentration diagram plotting stomate concentrations according to vegetation zone. Conifer stomate analysis was not able to resolve differences between forest-tundra and closed forest. Nevertheless, it was suggested that stomate analysis will become an important technique supplementing pollen analysis for reconstructing past tree-line changes since the presence of stomata in lakes make it possible to separate the tundra from forest-tundra and closed forest. The limited dispersal of conifer stomata permitted a better resolution of tree-line boundaries than did pollen. 13 refs., 3 figs.

Vital areas at nuclear power plants

International Nuclear Information System (INIS)

Cameron, D.F.

1985-01-01

Vital area analysis of nuclear power plants has been performed for the Nuclear Regulatory Commission by the Los Alamos National Laboratory from the late 1970's through the present. The Los Alamos Vital Area Study uses a fault-tree modeling technique to identify vital areas and equipment at nuclear power plants to determine their vulnerability. This technique has been applied to all operating plants and approximately one-half of those under construction in the US. All saboteur-induced loss-of-coolant accidents and transients and the systems needed to mitigate them are considered. As a result of this effort, security programs at nuclear power plants now include vulnerability studies that identify targets in a systematic manner, and thus unnecessary protection has been minimized. 1 ref., 8 figs., 1 tab

Cloud-Based Automated Design and Additive Manufacturing: A Usage Data-Enabled Paradigm Shift.

Science.gov (United States)

Lehmhus, Dirk; Wuest, Thorsten; Wellsandt, Stefan; Bosse, Stefan; Kaihara, Toshiya; Thoben, Klaus-Dieter; Busse, Matthias

2015-12-19

Integration of sensors into various kinds of products and machines provides access to in-depth usage information as basis for product optimization. Presently, this large potential for more user-friendly and efficient products is not being realized because (a) sensor integration and thus usage information is not available on a large scale and (b) product optimization requires considerable efforts in terms of manpower and adaptation of production equipment. However, with the advent of cloud-based services and highly flexible additive manufacturing techniques, these obstacles are currently crumbling away at rapid pace. The present study explores the state of the art in gathering and evaluating product usage and life cycle data, additive manufacturing and sensor integration, automated design and cloud-based services in manufacturing. By joining and extrapolating development trends in these areas, it delimits the foundations of a manufacturing concept that will allow continuous and economically viable product optimization on a general, user group or individual user level. This projection is checked against three different application scenarios, each of which stresses different aspects of the underlying holistic concept. The following discussion identifies critical issues and research needs by adopting the relevant stakeholder perspectives.

Cloud-Based Automated Design and Additive Manufacturing: A Usage Data-Enabled Paradigm Shift

Science.gov (United States)

Lehmhus, Dirk; Wuest, Thorsten; Wellsandt, Stefan; Bosse, Stefan; Kaihara, Toshiya; Thoben, Klaus-Dieter; Busse, Matthias

2015-01-01

Integration of sensors into various kinds of products and machines provides access to in-depth usage information as basis for product optimization. Presently, this large potential for more user-friendly and efficient products is not being realized because (a) sensor integration and thus usage information is not available on a large scale and (b) product optimization requires considerable efforts in terms of manpower and adaptation of production equipment. However, with the advent of cloud-based services and highly flexible additive manufacturing techniques, these obstacles are currently crumbling away at rapid pace. The present study explores the state of the art in gathering and evaluating product usage and life cycle data, additive manufacturing and sensor integration, automated design and cloud-based services in manufacturing. By joining and extrapolating development trends in these areas, it delimits the foundations of a manufacturing concept that will allow continuous and economically viable product optimization on a general, user group or individual user level. This projection is checked against three different application scenarios, each of which stresses different aspects of the underlying holistic concept. The following discussion identifies critical issues and research needs by adopting the relevant stakeholder perspectives. PMID:26703606

Identifying variables that influence manufacturing product quality

Directory of Open Access Journals (Sweden)

Marek Krynke

2014-10-01

Full Text Available In the article a risk analysis of the production process of selected products in a plant producing votive candles was conducted. The Pareto-Lorenz diagram and FMEA method were used which indicated the most important areas affecting the production of selected elements of candles. The synthesis of intangible factors affecting production in the audited company was also carried out with particular emphasis on the operation of the production system. The factors determining the validity of studies was examined, describing the principle of BOST 14 Toyota management. The most important areas of the company were identified, positively affecting the production process.

An Aerial Radiological Survey of Selected Areas of Area 18 - Nevada Test Site

International Nuclear Information System (INIS)

Lyons, Craig

2009-01-01

-made radioisotopes. Spectral data can also identify specific radioactive isotopes. Based on the results of the RSL NTS 1994 surveys, this area was chosen for a resurvey to improve the spatial resolution of the reported depositions for the Johnnie Boy and Little Feller I events. In addition, the survey was expected to confirm the absence of detectable concentrations of Americium-241 (Am-241) at the Johnnie Boy site and attempt to confirm the presence of Uranium-235 (U-235).

Additional safety assessment of ITER - Addition safety investigation of the INB ITER

International Nuclear Information System (INIS)

2012-01-01

This assessment aims at re-assessing safety margins in the light of events which occurred in Fukushima Daiichi, i.e. extreme natural events challenging the safety of installations. After a presentation of some characteristics of the ITER installation (location, activities, buildings, premise detritiation systems, electric supply, handling means, radioactive materials, chemical products, nuclear risks, specific risks), the report addresses the installation robustness by identifying cliff-edge effect risks which can be related to a loss of confinement of radioactive materials, explosions, a significant increase of exposure level, a possible effect on water sheets, and so on. The next part addresses the various aspects related to a seismic risk: installation sizing (assessment methodology, seismic risk characterization in Cadarache), sizing protection measures, installation compliance, and margin assessment. External flooding is the next addressed risk: installation sizing with respect to this specific risk, protection measures, installation compliance, margin assessment, and studied additional measures. Other extreme natural phenomena are considered (meteorological conditions, earthquake and flood) which may have effects on other installations (dam, canal). Then, the report addresses technical risks like the loss of electric supplies and cooling systems, the way a crisis is managed in terms of technical and human means and organization in different typical accidental cases. Subcontracting practices are also discussed. A synthesis proposes an overview of this additional safety assessment and discusses the impact which could have additional measures which could be implemented

Method for identifying particulate fluoride compounds

Energy Technology Data Exchange (ETDEWEB)

Tufts, B J

1960-01-01

A method is described for identifying particulates containing fluorides and other complex fluorine compounds such as fluorosilicate in samples collected on membrane filters. The filter is treated with lead chloride to precipitate lead chlorofluoride at each fluoride-containing spot. This microspot is identified by examination in a light microscope. Sulfate and phosphate, which also precipitate if present, can be distinguished and do not interfere. Calibrations are given for the fluorides and the more insoluble salts, relating the original particle size to the reaction site size. Thus, the mass of the particles can be calculated. Results of some field tests in an area of fluoride pollution are given, and compared with standard testing procedures.

Identifying ecosystem service hotspots for environmental management in Durban, South Africa

Directory of Open Access Journals (Sweden)

Rashieda Davids

2016-12-01

Conclusion: The results indicated that substantial portions of hotspot areas lie outside of formally regulated and managed conservation areas and remain vulnerable to human impact and habitat degradation. The study identified management areas and options that could yield maximum benefits; including the need for the development of an ecosystem services management and protection strategy, the selection of areas for co-management of ecosystem service hotspots and CBAs and the need for collaborative management.

Use of probabilistic risk assessments to define areas of possible exemption from regulatory requirements

International Nuclear Information System (INIS)

Thompson, C.A.; Carlson, D.; Kolaczkowski, A.; LaChance, J.

1988-01-01

The Risk-Based Licensing Program (RBLP) was sponsored by the Department of Energy for the purpose of establishing and demonstrating an approach for identifying potential areas for exemption from current regulatory requirements in the licensing of nuclear power plants. Such an approach could assist in the improvement of the regulatory process for both current and future nuclear plant designs. Use of the methodology could result in streamlining the regulatory process by eliminating unnecessarily detailed reviews of portions of a plant design not important to risk. The RBLP methodology utilizes probabilistic risk assessments, (PRAs), which are required of all future applicants for nuclear power plant licenses. PRA results are used as a screening tool to determine the risk significance of various plant features which are correlated to the risk importance of regulations to identify potential areas for regulatory exemption. Additional consideration is then given to non-risk factors in the final determination of exemption candidates. The RBLP methodology was demonstrated using an existing PRA. The results of the demonstration are highlighted. 10 refs

Identification of seismically susceptible areas in western Himalaya ...

Indian Academy of Sciences (India)

This study is an attempt to identify seismically susceptible areas in western Himalaya, using pattern recognition ... a combination of both qualitative and quantita- tive features. .... Three distinct types of zones were identified: S1 was identified as ...

Detecting Large-Scale Landslides Using Lidar Data and Aerial Photos in the Namasha-Liuoguey Area, Taiwan

Directory of Open Access Journals (Sweden)

Meei-Ling Lin

2013-12-01

Full Text Available Large-scale landslides often cause severe damage to lives and properties; therefore, their identification is essential in order to adopt proper mitigation measures. The objective of this study was to set up a methodological approach to help identify large-scale landslides using Lidar data, aerial photos and field investigation. The selected study areas were the Namasha and Liuoguey Areas in Kaohsiung City, Taiwan, both of which were severely hit by the Typhoon Morakot in 2009. The identification of large-scale landslides was performed based on Lidar high-resolution topographic information. The linear structures were mapped according to the shading map, with aspect in different azimuth to show good details of the structures. The scarps of the landslides were also identified. Validation of the results was done using both aerial photos and field investigations. In addition, stability analyses were performed on designated cases to further validate the results of Lidar identification.

77 FR 63418 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Science.gov (United States)

2012-10-16

... significant foreign narcotics traffickers as identified by the President. In addition, the Secretary of the..., Zapopan, Jalisco C.P. 45238, Mexico; Cancun, Quintana Roo, Mexico; R.F.C. SRC-080222-274 (Mexico) [SDNTK..., Guadalajara, Jalisco C.P. 44130, Mexico; R.F.C. UNI-031118-2I6 (Mexico) [SDNTK]. In addition, OFAC is...

Meta-analysis of genome-wide association data and large-scale replication identifies additional susceptibility loci for type 2 diabetes

DEFF Research Database (Denmark)

Zeggini, Eleftheria; Scott, Laura J; Saxena, Richa

2008-01-01

analyses had limited power to identify variants with modest effects, we carried out meta-analysis of three T2D GWA scans comprising 10,128 individuals of European descent and approximately 2.2 million SNPs (directly genotyped and imputed), followed by replication testing in an independent sample......Genome-wide association (GWA) studies have identified multiple loci at which common variants modestly but reproducibly influence risk of type 2 diabetes (T2D). Established associations to common and rare variants explain only a small proportion of the heritability of T2D. As previously published...

Underground Test Area Fiscal Year 2012 Annual Quality Assurance Report Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Farnham, Irene [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States); Marutzky, Sam [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States)

2013-01-01

This report is mandated by the Underground Test Area (UGTA) Quality Assurance Project Plan (QAPP) and identifies the UGTA quality assurance (QA) activities for fiscal year (FY) 2012. All UGTA organizations—U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO); Desert Research Institute (DRI); Lawrence Livermore National Laboratory (LLNL); Los Alamos National Laboratory (LANL); Navarro-Intera, LLC (N-I); National Security Technologies, LLC (NSTec); and the U.S. Geological Survey (USGS)—conducted QA activities in FY 2012. The activities included conducting assessments, identifying findings and completing corrective actions, evaluating laboratory performance, revising the QAPP, and publishing documents. In addition, processes and procedures were developed to address deficiencies identified in the FY 2011 QAPP gap analysis.

Identifying multidrug resistant tuberculosis transmission hotspots using routinely collected data12

Science.gov (United States)

Manjourides, Justin; Lin, Hsien-Ho; Shin, Sonya; Jeffery, Caroline; Contreras, Carmen; Cruz, Janeth Santa; Jave, Oswaldo; Yagui, Martin; Asencios, Luis; Pagano, Marcello; Cohen, Ted

2012-01-01

SUMMARY In most countries with large drug resistant tuberculosis epidemics, only those cases that are at highest risk of having MDRTB receive a drug sensitivity test (DST) at the time of diagnosis. Because of this prioritized testing, identification of MDRTB transmission hotspots in communities where TB cases do not receive DST is challenging, as any observed aggregation of MDRTB may reflect systematic differences in how testing is distributed in communities. We introduce a new disease mapping method, which estimates this missing information through probability–weighted locations, to identify geographic areas of increased risk of MDRTB transmission. We apply this method to routinely collected data from two districts in Lima, Peru over three consecutive years. This method identifies an area in the eastern part of Lima where previously untreated cases have increased risk of MDRTB. This may indicate an area of increased transmission of drug resistant disease, a finding that may otherwise have been missed by routine analysis of programmatic data. The risk of MDR among retreatment cases is also highest in these probable transmission hotspots, though a high level of MDR among retreatment cases is present throughout the study area. Identifying potential multidrug resistant tuberculosis (MDRTB) transmission hotspots may allow for targeted investigation and deployment of resources. PMID:22401962

LAVA: Large scale Automated Vulnerability Addition

Science.gov (United States)

2016-05-23

LAVA: Large-scale Automated Vulnerability Addition Brendan Dolan -Gavitt∗, Patrick Hulin†, Tim Leek†, Fredrich Ulrich†, Ryan Whelan† (Authors listed...released, and thus rapidly become stale. We can expect tools to have been trained to detect bugs that have been released. Given the commercial price tag...low TCN) and dead (low liveness) program data is a powerful one for vulnera- bility injection. The DUAs it identifies are internal program quantities

Risk perception and access to environmental information in four areas in Italy affected by natural or anthropogenic pollution.

Science.gov (United States)

Coi, A; Minichilli, F; Bustaffa, E; Carone, S; Santoro, M; Bianchi, F; Cori, L

2016-10-01

A human biomonitoring (HBM) survey in four areas affected by natural or anthropogenic arsenic pollution was conducted in Italy within the framework of the SEpiAs project. A questionnaire, including the exploration of risk perception (RP) regarding environmental hazards and access to and trust in information, was administered to 282 subjects stratified by area, gender and age. The survey was designed to investigate how populations living in polluted areas could adopt prevention-oriented habits, fostered by the awareness of existing risks and, in addition, how increased knowledge of RP and information flows could support researchers in identifying recommendations, and presenting and disseminating HBM results. This study characterizes the four areas in terms of RP and access to and trust in environmental information, and provides insights into the influence of RP and environmental information on food consumption. For the data analysis, a combined random forest (RF) and logistic regression approach was carried out. RF was applied to the variables derived from the questionnaire in order to identify the most important in terms of the aims defined. Associations were then tested using Fisher's exact test and assessed with logistic regression in order to adjust for confounders. Results showed that the perception of and personal exposure to atmospheric and water pollution, hazardous industries and waste, hazardous material transportation and waste was higher in geographical areas characterized by anthropogenic pollution. Citizens living in industrial areas appeared to be aware of environmental risks and had more confidence in environmental non-governmental organizations (NGOs) than in public authorities. In addition, they reported an insufficient circulation of information. Concerning the influence of RP and environmental information on food consumption, a high perception of personal exposure to atmospheric pollution and hazardous industries was associated with a lower

Zero additives preservation of Raphia palm wine | Dioha ...

African Journals Online (AJOL)

Palm wine obtained from Raphia palm (Raphia hookeri) in Ayingba, Kogi State, Nigeria, was pasteurized through zero addition of preservative and placed on the shelf for 6 months. After 6 months, another sample of palm wine obtained from the same area was fetched and comparative analysis was carried out on both wine ...

200 area effluent treatment facility opertaional test report

International Nuclear Information System (INIS)

Crane, A.F.

1995-01-01

This document reports the results of the 200 Area Effluent Treatment Facility (200 Area ETF) operational testing activities. These Operational testing activities demonstrated that the functional, operational and design requirements of the 200 Area ETF have been met and identified open items which require retesting

Defining urban and rural areas: a new approach

Science.gov (United States)

Arellano, Blanca; Roca, Josep

2017-10-01

The separation between the countryside and the city, from rural and urban areas, has been one of the central themes of the literature on urban and territorial studies. The seminal work of Kingsley Davis [10] in the 1950s introduced a wide and fruitful debate which, however, has not yet concluded in a rigorous definition that allows for comparative studies at the national and subnational levels of a scientific nature. In particular, the United Nations (UN) definition of urban and rural population is overly linked to political and administrative factors that make it difficult to use data adequately to understand the human settlement structure of different countries. The present paper seeks to define a more rigorous methodology for the identification of rural and urban areas. For this purpose it uses the night lights supplied by the SNPP satellite, and more specifically by the VIIRS sensor for the determination of the urbanization gradient, and by means of the same construct a more realistic indicator than the statistics provided by the UN. The arrival of electrification to nearly every corner of the planet is certainly the first and most meaningful indicator of artificialization of land. In this sense, this paper proposes a new methodology designed to identify highly impacted (urbanized) landscapes worldwide based on the analysis of satellite imagery of night-time lights. The application of this methodology on a global scale identifies the land highly impacted by light, the urbanization process, and allows an index to be drawn up of Land Impacted by Light per capita (LILpc) as an indicator of the level of urbanization. The methodology used in this paper can be summarized in the following steps: a) a logistic regression between US Urban Areas (UA), as a dependent variable, and night-time light intensity, as an explanatory variable, allows us to establish a nightlight intensity level for the determination of Areas Highly Impacted by Light (AHIL); b) the delimitation of

Identifying the Transgender Population in the Medicare Program

Science.gov (United States)

Proctor, Kimberly; Haffer, Samuel C.; Ewald, Erin; Hodge, Carla; James, Cara V.

2016-01-01

Abstract Purpose: To identify and describe the transgender population in the Medicare program using administrative data. Methods: Using a combination of International Classification of Diseases ninth edition (ICD-9) codes relating to transsexualism and gender identity disorder, we analyzed 100% of the 2013 Centers for Medicare & Medicaid Services (CMS) Medicare Fee-For-Service (FFS) “final action” claims from both institutional and noninstitutional providers (∼1 billion claims) to identify individuals who may be transgender Medicare beneficiaries. To confirm, we developed and applied a multistage validation process. Results: Four thousand ninety-eight transgender beneficiaries were identified, of which ∼90% had confirmatory diagnoses, billing codes, or evidence of a hormone prescription. In general, the racial, ethnic, and geographic distribution of the Medicare transgender population tends to reflect the broader Medicare population. However, age, original entitlement status, and disease burden of the transgender population appear substantially different. Conclusions: Using a variety of claims information, ranging from claims history to additional diagnoses, billing modifiers, and hormone prescriptions, we demonstrate that administrative data provide a valuable resource for identifying a lower bound of the Medicare transgender population. In addition, we provide a baseline description of the diversity and disease burden of the population and a framework for future research. PMID:28861539

Radon in dwellings in selected areas of Ireland

International Nuclear Information System (INIS)

Madden, J.S.; Duffy, J.T.; Mackin, G.A.; Colgan, P.A.; McGarry, A.T.

1994-10-01

This report presents and interprets the results of surveys of domestic radon concentrations carried out by the Radiological Protection Institute of Ireland between 1989 and 1992. Data from low-density monitoring surveys in counties Mayo, Galway (including the Aran Island of Inis Mor) and Clare and in north Kerry, in addition to more detailed surveys in Moycullen and Salthill in Co. Galway and south Cork city are presented. The highest seasonally-corrected radon level found in any of the 1755 dwellings surveyed was 2399 Bq/m 3 . This is twelve times the national Reference Level of 200 Bq/m 3 , and corresponds to an annual radiation dose to occupants of the house of 60 mSv, three times the maximum dose which radiation workers are allowed to receive under internationally-accepted standards. Statistical evaluation of the data has allowed classification of 10 km grid square areas on the basis of the predicted proportion of houses in each grid square with radon levels in excess of the national Reference Level, 200 Bq/m 3 . The most affected areas occur in counties Mayo and Galway, and to a lesser extent in south-east Cork city. In county Galway six grid squares are predicted to have more than 20% of houses with radon concentrations in excess of 200 Bq/m 3 . In the most affected grid square 30% of houses are predicted to have radon concentrations in excess of this level. It is important that householders in these areas be strongly encouraged to have the radon levels in their houses measured in order to identify the individual houses in which remedial measures are required. The risk associated with longterm exposure to radon has been calculated using the latest risk factor recommended by the International Commission on Radiological Protection. For average residents exposed to indoor radon concentrations of 200 Bq/m 3 the estimated lifetime risk of premature death from lung cancer, due to radon, is about 2%. This risk is a significant addition to the prevailing lifetime

Waste site grouping for 200 Areas soil investigations

International Nuclear Information System (INIS)

1997-01-01

The purpose of this document is to identify logical waste site groups for characterization based on criteria established in the 200 Areas Soil Remediation Strategy (DOE-RL 1996a). Specific objectives of the document include the following: finalize waste site groups based on the approach and preliminary groupings identified in the 200 Areas Soil Remediation Strategy; prioritize the waste site groups based on criteria developed in the 200 Areas Soil Remediation Strategy; select representative site(s) that best represents typical and worse-case conditions for each waste group; develop conceptual models for each waste group. This document will serve as a technical baseline for implementing the 200 Areas Soil Remediation Strategy. The intent of the document is to provide a framework, based on waste site groups, for organizing soil characterization efforts in the 200 Areas and to present initial conceptual models

Allegheny County Soil Type Areas

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset contains soil type and soil classification, by area. Additional info at: http://mcdc.cas.psu.edu/datawiz.htm;...

Hooded seal Cystophora cristata foraging areas in the Northeast Atlantic Ocean-Investigated using three complementary methods.

Directory of Open Access Journals (Sweden)

Jade Vacquie-Garcia

Full Text Available Identifying environmental characteristics that define the ecological niche of a species is essential to understanding how changes in physical conditions might affect its distribution and other aspects of its ecology. The present study used satellite relay data loggers (SRDLs to study habitat use by Northeast Atlantic hooded seals (N = 20; 9 adult females, 3 adult males, and 8 juveniles. Three different methods were used in combination to achieve maximum insight regarding key foraging areas for hooded seals in this region, which have decline by 85% in recent decades: 1 first passage time (FPT; 2 vertical transit rate and; 3 change in dive drift rate. Generalized additive mixed models (GAMM were applied to each method to determine whether specific habitat characteristics were associated with foraging. Separate models were run for the post-molting and the post-breeding seasons; sex and age classes were included in the GAMMs. All three methods highlighted a few common geographic areas as being important foraging zones; however, there were also some different areas identified by the different methods, which highlights the importance of using multiple indexes when analyzing tracking and diving data to study foraging behavior. Foraging occurred most commonly in relatively shallow areas with high Sea Surface Temperatures (SST, corresponding to continental shelf areas with Atlantic Water masses. All age and sex classes overlapped spatially to some extent, but the different age and sex groups showed differences in the bathymetry of their foraging areas as well as in their vertical use of the water column. When foraging, pups dove in the upper part of the water column in relatively deep areas. Adult females foraged relatively shallowly in deep water areas too, though in shallower areas than pups. Adult males foraged close to the bottom in shallower areas.

The effect of additional physiotherapy to hospital inpatients outside of regular business hours: a systematic review.

Science.gov (United States)

Brusco, Natasha K; Paratz, Jennifer

2006-12-01

Provision of out of regular business hours (OBH) physiotherapy to hospital inpatients is widespread in the hospital setting. This systematic review evaluated the effect of additional OBH physiotherapy services on patient length of stay (LOS), pulmonary complications, discharge destination, discharge mobility status, quality of life, cost saving, adverse events, and mortality compared with physiotherapy only within regular business hours. A literature search was completed on databases with citation tracking using key words. Two reviewers completed data extraction and quality assessment independently by using modified scales for historical cohorts and case control studies as well as the PEDro scale for randomized controlled trials and quasi-randomised controlled trials. This search identified nine articles of low to medium quality. Four reported a significant reduction in LOS associated with additional OBH physiotherapy, with two articles reporting overall significance and two reporting only for specific subgroups. Two studies reported significant reduction in pulmonary complications for two different patient groups in an intensive care unit (ICU) with additional OBH physiotherapy. Three studies accounted for discharge destination and/or discharge mobility status with no significant difference reported. Quality of life, adverse events, and mortality were not reported in any studies. Cost savings were considered in three studies, with two reporting a cost saving. This systematic review was unable to conclude that the provision of additional OBH physiotherapy made significant improvement to patient outcomes for all subgroups of inpatients. One study in critical care reported that overnight physiotherapy decreased LOS and reduced pulmonary complications of patients in the ICU. However, the studies in the area of orthopaedics, neurology, postcardiac surgery, and rheumatology, which all considered additional daytime weekend physiotherapy intervention, did not provide

Application of hydrochemistry and isotopic hydrology to identify recharge areas and characterize nitrate contamination in the Santiago Aquifer

International Nuclear Information System (INIS)

Tore, C; Grilli D-F, A; Aguirre, E.; Moya, P

2001-01-01

This work is the result of a joint effort of the Empresa Metropolitana de Obras Sanitarias (EMOS S. A. - Chile), the Comision Chilena de Energia Nuclear (CCHEN - Chile) and the International Atomic Energy Agency (IAEA - Austria). It has been carried out in the framework of the project ARCAL XXXI-RLA/8/023-9004 and under the auspice of the IAEA. This kind of project aims to provide technical knowledge in order to promote a sustainable use of groundwater resources for water supply in urban areas. The main goal of the ARCAL was to characterize the Santiago aquifer, specially those areas currently intensively exploited (or expected to be in the next future) and determine EMOS S. A. production wells capture zones to define protection areas. Among the specific objectives pursued it can be mentioned: -Determination of recharge areas and main hydrochemical features of groundwater in Santiago -Characterization of nitrate pollution and its most probable source (au)

Mapping burned areas using dense time-series of Landsat data

Science.gov (United States)

Hawbaker, Todd J.; Vanderhoof, Melanie; Beal, Yen-Ju G.; Takacs, Joshua; Schmidt, Gail L.; Falgout, Jeff T.; Williams, Brad; Brunner, Nicole M.; Caldwell, Megan K.; Picotte, Joshua J.; Howard, Stephen M.; Stitt, Susan; Dwyer, John L.

2017-01-01

Complete and accurate burned area data are needed to document patterns of fires, to quantify relationships between the patterns and drivers of fire occurrence, and to assess the impacts of fires on human and natural systems. Unfortunately, in many areas existing fire occurrence datasets are known to be incomplete. Consequently, the need to systematically collect burned area information has been recognized by the United Nations Framework Convention on Climate Change and the Intergovernmental Panel on Climate Change, which have both called for the production of essential climate variables (ECVs), including information about burned area. In this paper, we present an algorithm that identifies burned areas in dense time-series of Landsat data to produce the Landsat Burned Area Essential Climate Variable (BAECV) products. The algorithm uses gradient boosted regression models to generate burn probability surfaces using band values and spectral indices from individual Landsat scenes, lagged reference conditions, and change metrics between the scene and reference predictors. Burn classifications are generated from the burn probability surfaces using pixel-level thresholding in combination with a region growing process. The algorithm can be applied anywhere Landsat and training data are available. For this study, BAECV products were generated for the conterminous United States from 1984 through 2015. These products consist of pixel-level burn probabilities for each Landsat scene, in addition to, annual composites including: the maximum burn probability and a burn classification. We compared the BAECV burn classification products to the existing Global Fire Emissions Database (GFED; 1997–2015) and Monitoring Trends in Burn Severity (MTBS; 1984–2013) data. We found that the BAECV products mapped 36% more burned area than the GFED and 116% more burned area than MTBS. Differences between the BAECV products and the GFED were especially high in the West and East where the

Geophysical investigations of the Seferihisar geothermal area, Western Anatolia, Turkey

Energy Technology Data Exchange (ETDEWEB)

Drahor, Mahmut G.; Berge, Meric A. [Dokuz Eyluel University, Engineering Faculty, Department of Geophysics, Tinaztepe Campus, 35160 Buca-Izmir (Turkey)

2006-06-15

Self-potential (SP), magnetic and very low frequency electromagnetic (EM-VLF) surveys were carried out in the Seferihisar geothermal area to identify major and minor fault zones and characterize the geothermal system. The SP study provided useful information on the local faults and subsurface fluid flow. The main SP anomalies appear mostly along and near active fault zones in the area of the Cumali, Tuzla and Doganbey hot springs. Two of these anomalies near the Tuzla hot springs were further evaluated by SP modelling. Total magnetic field values increase from the Doganbey to the Cumali hot springs. Modelling performed on the magnetic data indicates that between these two spring areas are four different regions or units that can be distinguished on the basis of their magnetic susceptibility values. Fraser filtering of EM-VLF data also indicates that there are three significant conductive zones in the regions around the Cumali, Tuzla and Doganbey hot springs, and that they lie between important fault systems. The EM-VLF and total (stacked) SP data show that the conductive tilt anomalies obtained by Fraser filtering generally coincide with negative SP areas. According to our geophysical investigations, new exploratory wells should be drilled into the conductive zones located between the Cumali and Tuzla hot springs. We further recommend that resistivity and magnetotelluric methods be carried out in the area to obtain additional information on the Seferihisar geothermal system. (author)

Tourism, biodiversity and protected areas--Review from northern Fennoscandia.

Science.gov (United States)

Tolvanen, Anne; Kangas, Katja

2016-03-15

Tourist numbers in northern Fennoscandia outweigh those in other northern boreal - arctic regions, which creates a specific need to evaluate the impacts of tourism. This review 1) identifies patterns and trends in the vegetation and wildlife of northern Fennoscandian terrestrial ecosystems as a consequence of tourism and recreation, 2) discusses the implications of findings in terms of the intensity, area and magnitude of impacts, changing climate and management needs under increasing tourist pressure, and 3) identifies research gaps. The reviewed studies show negative environmental and biodiversity impacts that are most pronounced near tourist resorts. The most sensitive plants, birds and mammals decline or disappear from the disturbed sites, and the species composition shifts from 'wild' species to cultural and human associated species. There is little research on the spread of alien species, but the few examples show that alien species can be promoted by tourism activities. Impacts of the use of motorized vehicles have not been widely studied either, despite the extensive track network which can cause disturbance to wildlife. The integrated impacts of tourism and climate change on the vegetation and wildlife was not addressed directly in any of the reviewed studies. In addition, little research has been done on carrying out restoration at tourist areas. Scientific research on these topics is needed to prevent, minimize or restore the most negative ecological impacts of tourism and recreation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Threats from urban expansion, agricultural transformation and forest loss on global conservation priority areas

Science.gov (United States)

Moilanen, Atte; Di Minin, Enrico

2017-01-01

Including threats in spatial conservation prioritization helps identify areas for conservation actions where biodiversity is at imminent risk of extinction. At the global level, an important limitation when identifying spatial priorities for conservation actions is the lack of information on the spatial distribution of threats. Here, we identify spatial conservation priorities under three prominent threats to biodiversity (residential and commercial development, agricultural expansion, and forest loss), which are primary drivers of habitat loss and threaten the persistence of the highest number of species in the International Union for the Conservation of Nature (IUCN) Red List, and for which spatial data is available. We first explore how global priority areas for the conservation of vertebrate (mammals, birds, and amphibians) species coded in the Red List as vulnerable to each threat differ spatially. We then identify spatial conservation priorities for all species vulnerable to all threats. Finally, we identify the potentially most threatened areas by overlapping the identified priority areas for conservation with maps for each threat. We repeat the same with four other well-known global conservation priority area schemes, namely Key Biodiversity Areas, Biodiversity Hotspots, the global Protected Area Network, and Wilderness Areas. We find that residential and commercial development directly threatens only about 4% of the global top 17% priority areas for species vulnerable under this threat. However, 50% of the high priority areas for species vulnerable to forest loss overlap with areas that have already experienced some forest loss. Agricultural expansion overlapped with ~20% of high priority areas. Biodiversity Hotspots had the greatest proportion of their total area under direct threat from all threats, while expansion of low intensity agriculture was found to pose an imminent threat to Wilderness Areas under future agricultural expansion. Our results

Turbulence and Cavitation Suppression by Quaternary Ammonium Salt Additives.

Science.gov (United States)

Naseri, Homa; Trickett, Kieran; Mitroglou, Nicholas; Karathanassis, Ioannis; Koukouvinis, Phoevos; Gavaises, Manolis; Barbour, Robert; Diamond, Dale; Rogers, Sarah E; Santini, Maurizio; Wang, Jin

2018-05-16

We identify the physical mechanism through which newly developed quaternary ammonium salt (QAS) deposit control additives (DCAs) affect the rheological properties of cavitating turbulent flows, resulting in an increase in the volumetric efficiency of clean injectors fuelled with diesel or biodiesel fuels. Quaternary ammonium surfactants with appropriate counterions can be very effective in reducing the turbulent drag in aqueous solutions, however, less is known about the effect of such surfactants in oil-based solvents or in cavitating flow conditions. Small-angle neutron scattering (SANS) investigations show that in traditional DCA fuel compositions only reverse spherical micelles form, whereas reverse cylindrical micelles are detected by blending the fuel with the QAS additive. Moreover, experiments utilising X-ray micro computed tomography (micro-CT) in nozzle replicas, quantify that in cavitation regions the liquid fraction is increased in the presence of the QAS additive. Furthermore, high-flux X-ray phase contrast imaging (XPCI) measurements identify a flow stabilization effect in the region of vortex cavitation by the QAS additive. The effect of the formation of cylindrical micelles is reproduced with computational fluid dynamics (CFD) simulations by including viscoelastic characteristics for the flow. It is demonstrated that viscoelasticity can reduce turbulence and suppress cavitation, and subsequently increase the injector's volumetric efficiency.

An alternative method for identifying booms and busts in the euro area housing market

OpenAIRE

Gerdesmeier, Dieter; Roffia, Barbara; Lenarcic, Andreja

2012-01-01

The main aim of this paper is to apply a method based on fundamentals ─ which has already been applied in the stock market analysis ─ to detect boom/bust in the housing market, with a focus on the euro area. In this context, an underlying model is developed and tested. It turns out that the user cost rate, a demographic variable, the unemployment rate, disposable income (or disposable income per capita), the debt-to-income ratio and, finally, the housing stock are fundamental variables which ...

Are some areas more equal than others? Socioeconomic inequality in potentially avoidable emergency hospital admissions within English local authority areas.

Science.gov (United States)

Sheringham, Jessica; Asaria, Miqdad; Barratt, Helen; Raine, Rosalind; Cookson, Richard

2017-04-01

Objectives Reducing health inequalities is an explicit goal of England's health system. Our aim was to compare the performance of English local administrative areas in reducing socioeconomic inequality in emergency hospital admissions for ambulatory care sensitive chronic conditions. Methods We used local authority area as a stable proxy for health and long-term care administrative geography between 2004/5 and 2011/12. We linked inpatient hospital activity, deprivation, primary care, and population data to small area neighbourhoods (typical population 1500) within administrative areas (typical population 250,000). We measured absolute inequality gradients nationally and within each administrative area using neighbourhood-level linear models of the relationship between national deprivation and age-sex-adjusted emergency admission rates. We assessed local equity performance by comparing local inequality against national inequality to identify areas significantly more or less equal than expected; evaluated stability over time; and identified where equity performance was steadily improving or worsening. We then examined associations between change in socioeconomic inequalities and change in within-area deprivation (gentrification). Finally, we used administrative area-level random and fixed effects models to examine the contribution of primary care to inequalities in admissions. Results Data on 316 administrative areas were included in the analysis. Local inequalities were fairly stable between consecutive years, but 32 areas (10%) showed steadily improving or worsening equity. In the 21 improving areas, the gap between most and least deprived fell by 3.9 admissions per 1000 (six times the fall nationally) between 2004/5 and 2011/12, while in the 11 areas worsening, the gap widened by 2.4. There was no indication that measured improvements in local equity were an artefact of gentrification or that changes in primary care supply or quality contributed to changes in

It takes two-skilled recognition of objects engages lateral areas in both hemispheres.

Directory of Open Access Journals (Sweden)

Merim Bilalić

Full Text Available Our object recognition abilities, a direct product of our experience with objects, are fine-tuned to perfection. Left temporal and lateral areas along the dorsal, action related stream, as well as left infero-temporal areas along the ventral, object related stream are engaged in object recognition. Here we show that expertise modulates the activity of dorsal areas in the recognition of man-made objects with clearly specified functions. Expert chess players were faster than chess novices in identifying chess objects and their functional relations. Experts' advantage was domain-specific as there were no differences between groups in a control task featuring geometrical shapes. The pattern of eye movements supported the notion that experts' extensive knowledge about domain objects and their functions enabled superior recognition even when experts were not directly fixating the objects of interest. Functional magnetic resonance imaging (fMRI related exclusively the areas along the dorsal stream to chess specific object recognition. Besides the commonly involved left temporal and parietal lateral brain areas, we found that only in experts homologous areas on the right hemisphere were also engaged in chess specific object recognition. Based on these results, we discuss whether skilled object recognition does not only involve a more efficient version of the processes found in non-skilled recognition, but also qualitatively different cognitive processes which engage additional brain areas.

Identifying patient risks during hospitalization

Directory of Open Access Journals (Sweden)

Lucélia Ferreira Lima

2008-12-01

Full Text Available Objective: To identify the risks reported at a public institution andto know the main patient risks from the nursing staff point of view.Methods: A retrospective, descriptive and exploratory study. Thesurvey was developed at a hospital in the city of Taboão da Serra, SãoPaulo, Brazil. The study included all nurses working in care areas whoagreed to participate in the study. At the same time, sentinel eventsoccurring in the period from July 2006 to July 2007 were identified.Results: There were 440 sentinel events reported, and the main risksincluded patient falls, medication errors and pressure ulcers. Sixty-fivenurses were interviewed. They also reported patient falls, medicationerrors and pressure ulcers as the main risks. Conclusions: Riskassessment and implementation of effective preventive actions arenecessary to ensure patient’s safety. Involvement of a multidisciplinaryteam is one of the steps for a successful process.

Additional burden of asymptomatic and sub-patent malaria infections during low transmission season in forested tribal villages in Chhattisgarh, India.

Science.gov (United States)

Chourasia, Mehul Kumar; Raghavendra, Kamaraju; Bhatt, Rajendra M; Swain, Dipak Kumar; Meshram, Hemraj M; Meshram, Jayant K; Suman, Shrity; Dubey, Vinita; Singh, Gyanendra; Prasad, Kona Madhavinadha; Kleinschmidt, Immo

2017-08-08

The burden of sub-patent malaria is difficult to recognize in low endemic areas due to limitation of diagnostic tools, and techniques. Polymerase chain reaction (PCR), a molecular based technique, is one of the key methods for detection of low parasite density infections. The study objective was to assess the additional burden of asymptomatic and sub-patent malaria infection among tribal populations inhabiting three endemic villages in Keshkal sub-district, Chhattisgarh, India. A cross-sectional survey was conducted in March-June 2016, during the low transmission season, to measure and compare prevalence of malaria infection using three diagnostics: rapid diagnostic test, microscopy and nested-PCR. Out of 437 individuals enrolled in the study, 103 (23.6%) were malaria positive by PCR and/or microscopy of whom 89.3% were Plasmodium falciparum cases, 77.7% were afebrile and 35.9% had sub-patent infections. A substantial number of asymptomatic and sub-patent malaria infections were identified in the survey. Hence, strategies for identifying and reducing the hidden burden of asymptomatic and sub-patent infections should focus on forest rural tribal areas using more sensitive molecular diagnostic methods to curtail malaria transmission.

Antibacterial Behavior of Additively Manufactured Porous Titanium with Nanotubular Surfaces Releasing Silver Ions

NARCIS (Netherlands)

Amin Yavari, S.; Loozen, L.; Paganelli, F. L.; Bakhshandeh, S.; Lietaert, K.; Groot, J. A.; Fluit, A. C.; Boel, C. H E; Alblas, J.; Vogely, H. C.; Weinans, H.; Zadpoor, A. A.

2016-01-01

Additive manufacturing (3D printing) has enabled fabrication of geometrically complex and fully interconnected porous biomaterials with huge surface areas that could be used for biofunctionalization to achieve multifunctional biomaterials. Covering the huge surface area of such porous titanium with

Demographic Data - URBAN_AREAS_TIGER00_IN: Indiana Major Urban Areas (U.S. Census Bureau, 1:100,000, Polygon Shapefile)

Data.gov (United States)

NSGIC State | GIS Inventory — URBAN_AREAS_TIGER00_IN contains major urban areas in Indiana identified by the US Bureau of the Census. Data is from U.S. Department of Commerce, U.S. Census Bureau,...

Modern Trends of Additional Professional Education Development for Mineral Resource Extracting

Science.gov (United States)

Borisova, Olga; Frolova, Victoria; Merzlikina, Elena

2017-11-01

The article contains the results of development of additional professional education research, including the field of mineral resource extracting in Russia. The paper describes the levels of education received in Russian Federation and determines the place and role of additional professional education among them. Key factors influencing the development of additional professional education are identified. As a result of the research, the authors proved the necessity of introducing additional professional education programs on educational Internet platforms for mineral resource extracting.

76 FR 77696 - Establishment of the Naches Heights Viticultural Area

Science.gov (United States)

2011-12-14

... Decision. SUMMARY: This final rule establishes the 13,254-acre ``Naches Heights'' viticultural area in... origin of their wines and to allow consumers to better identify wines they may purchase. DATES: Effective... consumers to identify wines they may purchase. Establishment of a viticultural area is neither an approval...

SPARQL-enabled identifier conversion with Identifiers.org.

Science.gov (United States)

Wimalaratne, Sarala M; Bolleman, Jerven; Juty, Nick; Katayama, Toshiaki; Dumontier, Michel; Redaschi, Nicole; Le Novère, Nicolas; Hermjakob, Henning; Laibe, Camille

2015-06-01

On the semantic web, in life sciences in particular, data is often distributed via multiple resources. Each of these sources is likely to use their own International Resource Identifier for conceptually the same resource or database record. The lack of correspondence between identifiers introduces a barrier when executing federated SPARQL queries across life science data. We introduce a novel SPARQL-based service to enable on-the-fly integration of life science data. This service uses the identifier patterns defined in the Identifiers.org Registry to generate a plurality of identifier variants, which can then be used to match source identifiers with target identifiers. We demonstrate the utility of this identifier integration approach by answering queries across major producers of life science Linked Data. The SPARQL-based identifier conversion service is available without restriction at http://identifiers.org/services/sparql. © The Author 2015. Published by Oxford University Press.

SPARQL-enabled identifier conversion with Identifiers.org

Science.gov (United States)

Wimalaratne, Sarala M.; Bolleman, Jerven; Juty, Nick; Katayama, Toshiaki; Dumontier, Michel; Redaschi, Nicole; Le Novère, Nicolas; Hermjakob, Henning; Laibe, Camille

2015-01-01

Motivation: On the semantic web, in life sciences in particular, data is often distributed via multiple resources. Each of these sources is likely to use their own International Resource Identifier for conceptually the same resource or database record. The lack of correspondence between identifiers introduces a barrier when executing federated SPARQL queries across life science data. Results: We introduce a novel SPARQL-based service to enable on-the-fly integration of life science data. This service uses the identifier patterns defined in the Identifiers.org Registry to generate a plurality of identifier variants, which can then be used to match source identifiers with target identifiers. We demonstrate the utility of this identifier integration approach by answering queries across major producers of life science Linked Data. Availability and implementation: The SPARQL-based identifier conversion service is available without restriction at http://identifiers.org/services/sparql. Contact: sarala@ebi.ac.uk PMID:25638809

78 FR 60816 - Proposed Directive for Additional Seasonal or Year-Round Recreation Activities at Ski Areas

Science.gov (United States)

2013-10-02

... land management plan. Since SAROEA provides that snow sports must remain paramount at ski areas on NFS... Winter Sports Program Manager, 707-562-8842. Individuals who use telecommunication devices for the deaf...., Eastern Daylight Time, Monday through Friday. SUPPLEMENTARY INFORMATION: 1. Background and Need for the...

A fuzzy application on MICE hosting: An Iranian case study for locating suitable areas based on P.L Indexes

Directory of Open Access Journals (Sweden)

Nazanin Tabrizi

2012-04-01

Full Text Available Today, countries compete to gain political, economic, social and cultural advantages. In addition, cities are trying to demonstrate their predominance on local and regional levels and achieve development by using managerial science. Meetings, incentives, conventions and exhibitions tourism (MICE hosting as a significant element of urban tourism is one of the effective methods to obtain urban development around the world. However, no specialized planning and independent investments in regard to these activities have been organized in Iran. Aiming to identify suitable areas in the northern part of Iran, the present research intends to recognize the necessary physical and location related (P.L indexes to perform the specialized activities of MICE tourism in this region. So at first, indispensable indicators to accept special role of MICE tourism are identified and then using GIS and fuzzy method, adapted areas are assigned. The result map shows that a ribbon-like area near the Caspian Sea with two wide lands at central and western parts is a proper choice to host MICE activities in the region from the viewpoint of P.L indexes.

Landscape Character of Pongkor Mining Ecotourism Area

Science.gov (United States)

Kusumoarto, A.; Gunawan, A.; Machfud; Hikmat, A.

2017-10-01

Pongkor Mining Ecotourism Area has a diverse landscape character as a potential landscape resources for the development of ecotourism destination. This area is part of the Mount of Botol Resort, Halimun Salak National Park (HSNP). This area also has a fairly high biodiversity. This study aims to identify and analysis the category of landscape character in the Pongkor Mining Ecotourism Area for the development of ecotourism destination. This study used a descriptive approach through field surveys and interviews, was carried out through two steps : 1) identify the landscape character, and 2) analysis of the landscape character. The results showed that in areas set aside for ecotourism destination in Pongkor Mining, landscape character category scattered forests, tailing ponds, river, plain, and the built environment. The Category of landscape character most dominant scattered in the area is forest, here is the river, plain, tailing ponds, the built environment, and plain. The landscape character in a natural environment most preferred for ecotourism activities. The landscape character that spread in the natural environment and the built environment is a potential that must be protected and modified such as elimination of incongruous element, accentuation of natural form, alteration of the natural form, intensification and enhanced visual quality intensively to be developed as a ecotourism destination area.

Protected areas for environmental sustainability in Nigeria | Imasuen ...

African Journals Online (AJOL)

This paper is focused on protected areas for environmental sustainability in Nigeria. It has examined what protected areas are the meaning, especially as defined by the International Union for the Conservation of Nature (IUCN). A thorough investigation was done to identify the areas that were and are still protected in ...

Driftless Area Initiative Biomass Energy Project

Energy Technology Data Exchange (ETDEWEB)

Wright, Angie [Northeast Iowa Resource Conservation & Development, Inc., Postville, IA (United States); Bertjens, Steve [Natural Resources Conservation Service, Madison, WI (United States); Lieurance, Mike [Northeast Iowa Resource Conservation & Development, Inc., Postville, IA (United States); Berguson, Bill [Univ. of Minnesota, Minneapolis, MN (United States). Natural Resources Research Inst.; Buchman, Dan [Univ. of Minnesota, Minneapolis, MN (United States). Natural Resources Research Inst.

2012-12-31

The Driftless Area Initiative Biomass Energy Project evaluated the potential for biomass energy production and utilization throughout the Driftless Region of Illinois, Iowa, Minnesota and Wisconsin. The research and demonstration aspect of the project specifically focused on biomass energy feedstock availability and production potential in the region, as well as utilization potential of biomass feedstocks for heat, electrical energy production, or combined heat and power operations. The Driftless Region was evaluated because the topography of the area offers more acres of marginal soils on steep slopes, wooded areas, and riparian corridors than the surrounding “Corn Belt”. These regional land characteristics were identified as potentially providing opportunity for biomass feedstock production that could compete with traditional agriculture commodity crops economically. The project researched establishment methods and costs for growing switchgrass on marginal agricultural lands to determine the economic and quantitative feasibility of switchgrass production for biomass energy purposes. The project was successful in identifying the best management and establishment practices for switchgrass in the Driftless Area, but also demonstrated that simple economic payback versus commodity crops could not be achieved at the time of the research. The project also analyzed the availability of woody biomass and production potential for growing woody biomass for large scale biomass energy production in the Driftless Area. Analysis determined that significant resources exist, but costs to harvest and deliver to the site were roughly 60% greater than that of natural gas at the time of the study. The project contributed significantly to identifying both production potential of biomass energy crops and existing feedstock availability in the Driftless Area. The project also analyzed the economic feasibility of dedicated energy crops in the Driftless Area. High commodity crop prices

Moving Towards Sustainable Food Consumption : Identifying Barriers to Sustainable Student Diets

OpenAIRE

Ede, James; Graine, Sophia; Rhodes, Chris

2011-01-01

Adopting more sustainable consumption habits has been identified as a necessary step in the progression towards a sustainable society. In the area of sustainable consumption, personal food behaviour represents a strong leverage point. University students have been identified as a strategic audience; habits established during this transformative period can track forward into later life. This study seeks to identify the barriers inhibiting students from eating more sustainably. Perceived benefi...

Ozone Nonattainment Areas - 1 Hour

Data.gov (United States)

U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for Ozone - 1hour (Legacy...

[Estimates of the size of inhibitory areas in crowding effects in periphery].

Science.gov (United States)

Bondarko, V M; Danilova, M V; Solnushkin, S D; Chikhman, V N

2014-01-01

In psychophysical experiments we studied how surround influences recognition of test objects. The tests were low-contrast Landolt rings of the size 1.1, 1.5 and 2.3 deg. Their centers were located at 13.2 deg from the fixation point. The additional objects were similar Landolt rings or rings without gaps. The distance between the centers of the test and the additional objects varied from 2.2 to 13.2 deg. Inone experiment, the task of the observer was to identify both the test objects and the surrounding objects. In the second experiment the stimulus layout was the same, but'identification of only the test stimulus was required. In both experiments, deterioration of performance was found at all distances between the test objects and the surround, but the deterioration was more significant when the observer carried out the dual task. The data showed that the size of the inhibitory areas in our case does not comply with the Bouma low which states that the size of the interaction areas are equal to half of the eccentricity where the test is presented. Further deterioration of performance in the dual task reveals the contribution of attention into peripheral crowding effects.

Improvements in the Protein Identifier Cross-Reference service.

Science.gov (United States)

Wein, Samuel P; Côté, Richard G; Dumousseau, Marine; Reisinger, Florian; Hermjakob, Henning; Vizcaíno, Juan A

2012-07-01

The Protein Identifier Cross-Reference (PICR) service is a tool that allows users to map protein identifiers, protein sequences and gene identifiers across over 100 different source databases. PICR takes input through an interactive website as well as Representational State Transfer (REST) and Simple Object Access Protocol (SOAP) services. It returns the results as HTML pages, XLS and CSV files. It has been in production since 2007 and has been recently enhanced to add new functionality and increase the number of databases it covers. Protein subsequences can be Basic Local Alignment Search Tool (BLAST) against the UniProt Knowledgebase (UniProtKB) to provide an entry point to the standard PICR mapping algorithm. In addition, gene identifiers from UniProtKB and Ensembl can now be submitted as input or mapped to as output from PICR. We have also implemented a 'best-guess' mapping algorithm for UniProt. In this article, we describe the usefulness of PICR, how these changes have been implemented, and the corresponding additions to the web services. Finally, we explain that the number of source databases covered by PICR has increased from the initial 73 to the current 102. New resources include several new species-specific Ensembl databases as well as the Ensembl Genome ones. PICR can be accessed at http://www.ebi.ac.uk/Tools/picr/.

Uranium in the Bunter sediments of the Polish area

International Nuclear Information System (INIS)

Saldan, M.; Strzelecki, R.

1980-01-01

Uranium mineralization occurring in the Triassic sediments in the Polish area is discussed. Systematic work conducted for over ten years revealed the presence of uranium mineralization in the following geological units: Peribaltic syneclize, Fore-Sudetic monocline, Zary pericline and Pomerania trough. Out of three uranium-bearing horizons which can be correlated with each other two (the lower and the middle) are connected with the Middle Bunter, while the upper horizon is related to the Upper Bunter. Mineralization was found in sandstones, conglomerates, mudstones and claystones and, in the Fore-Sudetic monocline, also in carbonates. Among uranium minerals uranium black and coffinite were identified. In addition to uranium, increased vanadium, selenium and molybdenum contents were found in the sandstones. Some of the uranium-bearing horizons are of economic value. (author)

Enhanced Approximate Nearest Neighbor via Local Area Focused Search.

Energy Technology Data Exchange (ETDEWEB)

Gonzales, Antonio [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Blazier, Nicholas Paul [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-02-01

Approximate Nearest Neighbor (ANN) algorithms are increasingly important in machine learning, data mining, and image processing applications. There is a large family of space- partitioning ANN algorithms, such as randomized KD-Trees, that work well in practice but are limited by an exponential increase in similarity comparisons required to optimize recall. Additionally, they only support a small set of similarity metrics. We present Local Area Fo- cused Search (LAFS), a method that enhances the way queries are performed using an existing ANN index. Instead of a single query, LAFS performs a number of smaller (fewer similarity comparisons) queries and focuses on a local neighborhood which is refined as candidates are identified. We show that our technique improves performance on several well known datasets and is easily extended to general similarity metrics using kernel projection techniques.

Outcomes from the regional Co-operation in the Area of the Safety Analysis Methodology

International Nuclear Information System (INIS)

D'Auria, F.; Mavko, B.; Prosek, A.; Debrecin, N.; Bajs, T.

2000-01-01

International Atomic Energy Agency (IAEA) carried out the Co-ordinated Research Program (CRP) ON V alidation of Accident and Safety Analysis Methodology'' in the period between 1995 and 1998. Three areas of interest identified by the participants referred to the pressurised water reactors of Western and Eastern type (PWR and WWER type). The specific areas of attention were: system behaviour of the primary and secondary loops (PS area), the containment response (CO area) and the severe accidents (SA area). During the CRP it became clear that the technology advancements, the available tools (i.e. codes) and the experimental databases in the above areas are quite different. At the conclusion of the CRP, all objectives of the program have been reached. This paper presents the summary of the regional co-operation in this framework. The CRP activities focused on the codes and expertise available at the participating organisations. This overview therefore summarises their experience related to the state-of-the-art in the field of computational accident analysis. In addition, the paper proposes the recommendations for future activities related to the code usage, the user effects and code development. In pursuing of these goals special attention is given to the importance of the international co-operation. (author)

Oxidation processes on conducting carbon additives for lithium-ion batteries

KAUST Repository

La Mantia, Fabio; Huggins, Robert A.; Cui, Yi

2012-01-01

The oxidation processes at the interface between different types of typical carbon additives for lithium-ion batteries and carbonates electrolyte above 5 V versus Li/Li+ were investigated. Depending on the nature and surface area of the carbon

Placement of radium/barium sludges in tailings areas

International Nuclear Information System (INIS)

Murphy, K.L.; Multamaki, G.E.

1980-01-01

Currently radium is removed from uranium mining and milling effluents by the addition of barium chloride to precipitate the radium as radium/barium sulphate. The precipitate is allowed to settle in sedimentation basins prior to discharge of the effluent. The sedimentation basins are not suitable for final disposal of the sludge, and placement of the sludges in the tailings area has been proposed. The geochemical environment of fresh tailings areas was characterized as an acidic, oxidized surface zone underlain by an alkaline, reduced zone comprising the rest of the tailings. The quantity of sludge produced was estimated to be small relative to the quantity of tailings, and therefor a relatively small amount of radium would be added to the tailings disposal area by the addition of sludge. To confirm whether sludge addition affected radionuclide solubilization, laboratory leaching tests were conducted on slurries of acid leach tailings, and sludge-tailings mixtures. Radium in the (Ra,Ba)SO 4 sludge was at least as stable as radium in the tailings, and the sludge was able to absorb radium released from the tailings. The addition of sludge did not affect uranium and thorium solubilization. From these results it appears that the placement of sludge in tailings areas would not adversely affect the stability of radionuclides in the tailings or sludge. (auth)

Variant Carvajal syndrome with additional dental anomalies.

Science.gov (United States)

Barber, Sophy; Day, Peter; Judge, Mary; Toole, Edell O'; Fayle, Stephen

2012-09-01

This paper aims to review the case of a girl who presented with a number of dental anomalies, in addition to unusual skin, nail and hair conditions. Tragically an undiagnosed cardiomyopathy caused unexpected sudden death. The case is discussed with reference to a number of dermatological and oral conditions which were considered as possible diagnoses. AW had been under long term dental care for prepubertal periodontitis, premature root resorption of primary teeth, soft tissue and dental anomalies, and angular cheilitis. Separately she had also been seen by several dermatologists with respect to palmar plantar keratosis, striae keratoderma, wiry hair and abnormal finger nails. Tragically the patient suffered a sudden unexpected death and the subsequent post mortem identified an undiagnosed dilated cardiomyopathy. The most likely diagnosis is that this case is a variant of Carvajal Syndrome with additional dental anomalies. To date we have been unable to identify mutations in the desoplakin gene. We aim to emphasise the importance of recognising these dental and dermatological signs when they present together as a potential risk factor for cardiac abnormalities. © 2012 The Authors. International Journal of Paediatric Dentistry © 2012 BSPD, IAPD and Blackwell Publishing Ltd.

Addition computed tomography with stable xenon; Special reference to ischemic cerebrovascular diseases

Energy Technology Data Exchange (ETDEWEB)

Touho, Hajime; Karasawa, Jun; Shishido, Hisashi; Yamada, Keisuke; Shibamoto, Keiji [Osaka Neurological Inst., Toyonaka (Japan)

1990-09-01

Stable xenon (Xe{sup s}) is used as a contrast agent because it freely diffuses to cerebral tissues through the blood-brain barrier. In this study, 2 axial levels for Xe{sup s} enhancement analysis were selected from a baseline series of computed tomographic (CT) scans and 6 serial CT scans were obtained every 20 seconds for each scan level during the 240 seconds inhalation period of 30% Xe{sup s} in 10 volunteer controls and in 52 patients with ischemic cerebrovascular diseases (ICVD). The serial CT scans were added and averaged in each pixel. This was used to make a new CT picture (addition CT scans). The CT scans before the Xe{sup s} inhalation, the scan at the end of the Xe{sup s} inhalation, and the addition CT scan were compared to see whether gray matter and ischemic areas could be differentiated from white matter. The addition CT scans could differentiate the three structures very well in both the acute and chronic stages of ICVD. This technique is thought to be a very simple and useful method to detect the small infarcted areas and low perfusion areas that cannot be visualized on precontrast CT scans. (author).

Gender differentials in adoption of cassava value addition ...

African Journals Online (AJOL)

This study investigated adoption by gender of Cassava Value Addition Technologies (CVATs) in Imo State. It identified CVATs disseminated to farmers among other issues. Multi-stage random sampling technique was used in the selection of respondents. A sample size of 150 cassava farmers comprising of 75 male and 75 ...

PM 2.5 Nonattainment Areas

Data.gov (United States)

U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for PM 2.5 and have been...

Stormwater harvesting: Improving water security in South Africa's urban areas

Directory of Open Access Journals (Sweden)

Lloyd Fisher-Jeffes

2017-01-01

Full Text Available The drought experienced in South Africa in 2016 one of the worst in decades has left many urbanised parts of the country with limited access to water, and food production has been affected. If a future water crisis is to be averted, the country needs to conserve current water supplies, reduce its reliance on conventional surface water schemes, and seek alternative sources of water supply. Within urban areas, municipalities must find ways to adapt to, and mitigate the threats from, water insecurity resulting from, inter alia, droughts, climate change and increasing water demand driven by population growth and rising standards of living. Stormwater harvesting (SWH is one possible alternative water resource that could supplement traditional urban water supplies, as well as simultaneously offer a range of social and environmental benefits. We set out three position statements relating to how SWH can: improve water security and increase resilience to climate change in urban areas; prevent frequent flooding; and provide additional benefits to society. We also identify priority research areas for the future in order to target and support the appropriate uptake of SWH in South Africa, including testing the viability of SWH through the use of real-time control and managed aquifer recharge.

Modified Principal Component Analysis for Identifying Key Environmental Indicators and Application to a Large-Scale Tidal Flat Reclamation

Directory of Open Access Journals (Sweden)

Kejian Chu

2018-01-01

Full Text Available Identification of the key environmental indicators (KEIs from a large number of environmental variables is important for environmental management in tidal flat reclamation areas. In this study, a modified principal component analysis approach (MPCA has been developed for determining the KEIs. The MPCA accounts for the two important attributes of the environmental variables: pollution status and temporal variation, in addition to the commonly considered numerical divergence attribute. It also incorporates the distance correlation (dCor to replace the Pearson’s correlation to measure the nonlinear interrelationship between the variables. The proposed method was applied to the Tiaozini sand shoal, a large-scale tidal flat reclamation region in China. Five KEIs were identified as dissolved inorganic nitrogen, Cd, petroleum in the water column, Hg, and total organic carbon in the sediment. The identified KEIs were shown to respond well to the biodiversity of phytoplankton. This demonstrated that the identified KEIs adequately represent the environmental condition in the coastal marine system. Therefore, the MPCA is a practicable method for extracting effective indicators that have key roles in the coastal and marine environment.

Domestic Violence and Pregnancy: A CBPR Coalition Approach to Identifying Needs and Informing Policy.

Science.gov (United States)

Bright, Candace Forbes; Bagley, Braden; Pulliam, Ivie; Newton, Amy Swetha

2018-01-01

Community engagement-the collaborative process of addressing issues that impact the well-being of a community-is a strategic effort to address community issues. The Gulf States Health Policy Center (GS-HPC) formed the Hattiesburg Area Health Coalition (HAHC) in November 2014 for the purpose of addressing policies impacting the health of Forrest and Lamar counties in Mississippi. To chronicle the community-based participatory research (CBPR) process used by HAHC's identification of infant and maternal health as a policy area, domestic violence in pregnancy as a priority area within infant and maternal health, and a community action plan (CAP) regarding this priority area. HAHC reviewed data and identified infant and maternal health as a priority area. They then conducted a policy scan of local prenatal health care to determine the policy area of domestic violence in pregnancy. HAHC developed a CAP identifying three goals with regard to domestic violence and pregnancy that together informed policy. Changes included the development of materials specific to resources available in the area. The materials and recommended changes will first be implemented by Southeast Mississippi Rural Health Initiative (SeMRHI) through a screening question for all pregnant patients, and the adoption of policies for providing information and referrals. The lack of community-level data was a challenge to HAHC in identifying focus and priority areas, but this was overcome by shared leadership and community engagement. After completion of the CAP, 100% of expecting mothers receiving prenatal care in the area will be screened for domestic violence.

SPANISH PEAKS PRIMITIVE AREA, MONTANA.

Science.gov (United States)

Calkins, James A.; Pattee, Eldon C.

1984-01-01

A mineral survey of the Spanish Peaks Primitive Area, Montana, disclosed a small low-grade deposit of demonstrated chromite and asbestos resources. The chances for discovery of additional chrome resources are uncertain and the area has little promise for the occurrence of other mineral or energy resources. A reevaluation, sampling at depth, and testing for possible extensions of the Table Mountain asbestos and chromium deposit should be undertaken in the light of recent interpretations regarding its geologic setting.

Power spectrum scale invariance identifies prefrontal dysregulation in paranoid schizophrenia.

Science.gov (United States)

Radulescu, Anca R; Rubin, Denis; Strey, Helmut H; Mujica-Parodi, Lilianne R

2012-07-01

Theory and experimental evidence suggest that complex living systems function close to the boundary of chaos, with erroneous organization to an improper dynamical range (too stiff or chaotic) underlying system-wide dysregulation and disease. We hypothesized that erroneous organization might therefore also characterize paranoid schizophrenia, via optimization abnormalities in the prefrontal-limbic circuit regulating emotion. To test this, we acquired fMRI scans from 35 subjects (N = 9 patients with paranoid schizophrenia and N = 26 healthy controls), while they viewed affect-valent stimuli. To quantify dynamic regulation, we analyzed the power spectrum scale invariance (PSSI) of fMRI time-courses and computed the geometry of time-delay (Poincaré) maps, a measure of variability. Patients and controls showed distinct PSSI in two clusters (k(1) : Z = 4.3215, P = 0.00002 and k(2) : Z = 3.9441, P = 0.00008), localized to the orbitofrontal/medial prefrontal cortex (Brodmann Area 10), represented by β close to white noise in patients (β ≈ 0) and in the pink noise range in controls (β ≈ -1). Interpreting the meaning of PSSI differences, the Poincaré maps indicated less variability in patients than controls (Z = -1.9437, P = 0.05 for k(1) ; Z = -2.5099, P = 0.01 for k(2) ). That the dynamics identified Brodmann Area 10 is consistent with previous schizophrenia research, which implicates this area in deficits of working memory, executive functioning, emotional regulation and underlying biological abnormalities in synaptic (glutamatergic) transmission. Our results additionally cohere with a large body of work finding pink noise to be the normal range of central function at the synaptic, cellular, and small network levels, and suggest that patients show less supple responsivity of this region. Copyright © 2011 Wiley-Liss, Inc.

Extraction and Analysis of Information Related to Research & Development Declared Under an Additional Protocol

International Nuclear Information System (INIS)

Idinger, J.; Labella, R.; Rialhe, A.; Teller, N.

2015-01-01

The additional protocol (AP) provides important tools to strengthen and improve the effectiveness and efficiency of the safeguards system. Safeguards are designed to verify that States comply with their international commitments not to use nuclear material or to engage in nuclear-related activities for the purpose of developing nuclear weapons or other nuclear explosive devices. Under an AP based on INFCIRC/540, a State must provide to the IAEA additional information about, and inspector access to, all parts of its nuclear fuel cycle. In addition, the State has to supply information about its nuclear fuel cycle-related research and development (R&D) activities. The majority of States declare their R&D activities under the AP Articles 2.a.(i), 2.a.(x), and 2.b.(i) as part of initial declarations and their annual updates under the AP. In order to verify consistency and completeness of information provided under the AP by States, the Agency has started to analyze declared R&D information by identifying interrelationships between States in different R&D areas relevant to safeguards. The paper outlines the quality of R&D information provided by States to the Agency, describes how the extraction and analysis of relevant declarations are currently carried out at the Agency and specifies what kinds of difficulties arise during evaluation in respect to cross-linking international projects and finding gaps in reporting. In addition, the paper tries to elaborate how the reporting quality of AP information with reference to R&D activities and the assessment process of R&D information could be improved. (author)

A statistical GIS-based analysis of Wild boar (Sus scrofa traffic collisions in a Mediterranean area

Directory of Open Access Journals (Sweden)

Andrea Amici

2010-01-01

Full Text Available vThis study was aimed at analysing the most relevant environmental variables involved in vehicle–wild boar road collisions in a Mediterranean area, starting from a territorial information system implemented in a GIS environment. Landscape structure indices and local qualitative and quantitative variables were correlated to identify the most frequent predisposing factors of collisions. Statistical tests of the considered parameters indicated a higher frequency of collisions in the evening hours of late summer and autumn (P<0.05 compared with daytime and night-time, localized nearness to attraction points (feeding or resting sites; P<0.001 and closeness to no-hunting areas (P<0.001. In addition, local road parameters (shape of road, visibility at road sides, etc. considerably increased the risk of collisions.

Underground Test Area Fiscal Year 2013 Annual Quality Assurance Report Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Krenzien, Susan [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States); Marutzky, Sam [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States)

2014-01-01

This report is required by the Underground Test Area (UGTA) Quality Assurance Plan (QAP) and identifies the UGTA quality assurance (QA) activities for fiscal year (FY) 2013. All UGTA organizations—U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO); Desert Research Institute (DRI); Lawrence Livermore National Laboratory (LLNL); Los Alamos National Laboratory (LANL); Navarro-Intera, LLC (N-I); National Security Technologies, LLC (NSTec); and the U.S. Geological Survey (USGS)—conducted QA activities in FY 2013. The activities included conducting assessments, identifying findings and completing corrective actions, evaluating laboratory performance, and publishing documents. In addition, integrated UGTA required reading and corrective action tracking was instituted.

47 CFR 27.1208 - BTA service areas.

Science.gov (United States)

2010-10-01

.... Except for incumbent BRS licenses, BRS service areas are Basic Trading Areas (BTAs) or additional service... in places where Rand McNally has not defined BTAs: American Samoa; Guam; Gulf of Mexico Zone A; Gulf of Mexico Zone B; Gulf of Mexico Zone C; Northern Mariana Islands; Mayaguez/Aguadilla-Ponce, Puerto...

Identifying western yellow-billed cuckoo breeding habitat with a dual modelling approach

Science.gov (United States)

Johnson, Matthew J.; Hatten, James R.; Holmes, Jennifer A.; Shafroth, Patrick B.

2017-01-01

The western population of the yellow-billed cuckoo (Coccyzus americanus) was recently listed as threatened under the federal Endangered Species Act. Yellow-billed cuckoo conservation efforts require the identification of features and area requirements associated with high quality, riparian forest habitat at spatial scales that range from nest microhabitat to landscape, as well as lower-suitability areas that can be enhanced or restored. Spatially explicit models inform conservation efforts by increasing ecological understanding of a target species, especially at landscape scales. Previous yellow-billed cuckoo modelling efforts derived plant-community maps from aerial photography, an expensive and oftentimes inconsistent approach. Satellite models can remotely map vegetation features (e.g., vegetation density, heterogeneity in vegetation density or structure) across large areas with near perfect repeatability, but they usually cannot identify plant communities. We used aerial photos and satellite imagery, and a hierarchical spatial scale approach, to identify yellow-billed cuckoo breeding habitat along the Lower Colorado River and its tributaries. Aerial-photo and satellite models identified several key features associated with yellow-billed cuckoo breeding locations: (1) a 4.5 ha core area of dense cottonwood-willow vegetation, (2) a large native, heterogeneously dense forest (72 ha) around the core area, and (3) moderately rough topography. The odds of yellow-billed cuckoo occurrence decreased rapidly as the amount of tamarisk cover increased or when cottonwood-willow vegetation was limited. We achieved model accuracies of 75–80% in the project area the following year after updating the imagery and location data. The two model types had very similar probability maps, largely predicting the same areas as high quality habitat. While each model provided unique information, a dual-modelling approach provided a more complete picture of yellow-billed cuckoo habitat

DNA barcoding facilitates associations and diagnoses for Trichoptera larvae of the Churchill (Manitoba, Canada) area.

Science.gov (United States)

Ruiter, David E; Boyle, Elizabeth E; Zhou, Xin

2013-02-20

The North American Trichoptera larvae are poorly known at the species level, despite their importance in the understanding of freshwater fauna and critical use in biomonitoring. This study focused on morphological diagnoses for larvae occurring in the Churchill, Manitoba area, representing the largest larval association effort for the caddisflies at any given locality thus far. The current DNA barcode reference library of Trichoptera (available on the Barcode of Life Data Systems) was utilized to provide larval-adult associations. The present study collected an additional 23 new species records for the Churchill area, increasing the total Trichoptera richness to 91 species. We were able to associate 62 larval taxa, comprising 68.1% of the Churchill area Trichoptera taxa. This endeavor to identify immature life stage for the caddisflies enabled the development of morphological diagnoses, production of photographs and an appropriate taxonomic key to facilitate larval species analyses in the area. The use of DNA for associations of unknown larvae with known adults proved rapid and successful. This method should accelerate the state-of-knowledge for North American Trichoptera larvae as well as other taxonomic lineages. The morphological analysis should be useful for determination of material from the Churchill area.

Classification of suppressor additives based on synergistic and antagonistic ensemble effects

Energy Technology Data Exchange (ETDEWEB)

Broekmann, P., E-mail: peter.broekmann@iac.unibe.ch [BASF SE, Global Business Unit Electronic Materials, 67056 Ludwigshafen (Germany); Department of Chemistry and Biochemistry, University of Bern, Bern (Switzerland); Fluegel, A.; Emnet, C.; Arnold, M.; Roeger-Goepfert, C.; Wagner, A. [BASF SE, Global Business Unit Electronic Materials, 67056 Ludwigshafen (Germany); Hai, N.T.M. [Department of Chemistry and Biochemistry, University of Bern, Bern (Switzerland); Mayer, D. [BASF SE, Global Business Unit Electronic Materials, 67056 Ludwigshafen (Germany)

2011-05-01

Highlights: > Three fundamental types of suppressor additives for copper electroplating could be identified by means of potential transient measurements. > These suppressor additives differ in their synergistic and antagonistic interplay with anions that are chemisorbed on the metallic copper surface during electrodeposition. > In addition these suppressor chemistries reveal different barrier properties with respect to cupric ions and plating additives (Cl, SPS). - Abstract: Three fundamental types of suppressor additives for copper electroplating could be identified by means of potential transient measurements. These suppressor additives differ in their synergistic and antagonistic interplay with anions that are chemisorbed on the metallic copper surface during electrodeposition. In addition these suppressor chemistries reveal different barrier properties with respect to cupric ions and plating additives (Cl, SPS). While the type-I suppressor selectively forms efficient barriers for copper inter-diffusion on chloride-terminated electrode surfaces we identified a type-II suppressor that interacts non-selectively with any kind of anions chemisorbed on copper (chloride, sulfate, sulfonate). Type-I suppressors are vital for the superconformal copper growth mode in Damascene processing and show an antagonistic interaction with SPS (Bis-Sodium-Sulfopropyl-Disulfide) which involves the deactivation of this suppressor chemistry. This suppressor deactivation is rationalized in terms of compositional changes in the layer of the chemisorbed anions due to the competition of chloride and MPS (Mercaptopropane Sulfonic Acid) for adsorption sites on the metallic copper surface. MPS is the product of the dissociative SPS adsorption within the preexisting chloride matrix on the copper surface. The non-selectivity in the adsorption behavior of the type-II suppressor is rationalized in terms of anion/cation pairing effects of the poly-cationic suppressor and the anion-modified copper

Damping of Inter-Area Low Frequency Oscillation Using an Adaptive Wide-Area Damping Controller

DEFF Research Database (Denmark)

Yao, Wei; Jiang, L.; Fang, Jiakun

2013-01-01

This paper presents an adaptive wide-area damping controller (WADC) based on generalized predictive control (GPC) and model identification for damping the inter-area low frequency oscillations in large-scale inter-connected power system. A recursive least-squares algorithm (RLSA) with a varying...... forgetting factor is applied to identify online the reduced-order linearlized model which contains dominant inter-area low frequency oscillations. Based on this linearlized model, the generalized predictive control scheme considering control output constraints is employed to obtain the optimal control signal...... conditions and different disturbances, but also has better robustness against to the time delay existing in the remote signals. The comparison studies with the conventional lead-lag WADC are also provided....