Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (CuInSe2 based PV cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (CuInSe2 taiyo denchi seizo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on the fabrication technology of CuInSe2 based PV cell in fiscal 1994. (1) On formation of high-quality CIGS thin films by bilayer method, Mo film was deposited on a glass substrate by sputtering, and CIGS film with different Ga/In ratios was next formed on the substrate by quaternary simultaneous deposition at different In and Ga deposition speeds. In addition, CdS film was deposited on the CIGS film, and ZnO and ITO films were finally deposited on it by sputtering to complete solar cell. This solar cell offered the maximum conversion efficiency among cells using CIGS film. (2) On formation of high-quality CIGS thin films by three-stage method, a certain correlation was found between substrate temperature and CIGS film composition by monitoring substrate temperature in film forming process. This phenomenon allowed rigorous control of CIS film compositions important for CIS thin film solar cells. (3) On low-cost process technology for thin film formation, Cu(In,Ga)S2 solid solution film was fabricated by expanded selenic process. 3 figs.

Topside electron density at low latitudes

International Nuclear Information System (INIS)

Ezquer, R.G.; Cabrera, M.A.; Flores, R.F.; Mosert, M.

2002-01-01

The validity of IRI to predict the electron density at the topside electron density profile over the low latitude region is checked. The comparison with measurements obtained with the Taiyo satellite during low solar activity shows that, the disagreement between prediction and measurement is lower than 40% for 70% of considered cases. These IRI predictions are better than those obtained in a previous work at the southern peak of the equatorial anomaly for high solar activity. Additional studies for low solar activity, using ionosonde data as input parameters in the model, are needed in order to check if the observed deviations are due to the predicted peak characteristics or to the predicted shape of the topside profile. (author)

Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for development of extra-high efficiency solar cells (fundamental research on extra-high efficiency Si solar cells); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (chokokoritsu silicon taiyo denchi gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Sekikawa, T; Suzuki, E; Ishikawa, K; Takato, H; Yui, N; Shimokawa, R [Electrotechnical Laboratory, Tsukuba (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for analysis and evaluation for development of extra-high efficiency silicon solar cells. It is necessary for development of extra-high efficiency Si solar cells to extend as far as possible service life of minority carriers and to develop the evaluation techniques. Noting photoluminescence (PL) observable even with Si, the method of evaluating characteristics of minority carriers, which are not limited in samples, is developed to experimentally determine their service life from transitional response of the PL characteristics. Si has an extremely low quantum effect, because it is an indirect transitional semiconductor, and needs measurement of very high sensitivity. A rapid heat annealing apparatus and others to generate carriers in the infrared and ultraviolet regions are provided in consideration that these are possible means to increase efficiency. These possibilities will be pursued by developing the annealing techniques. 1 fig.

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of solar cell evaluation system (Survey of research and development of solar cell evaluation system); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi hyoka system no kenkyu kaihatsu (taiyo denchi hyoka system no kenkyu kaihatsu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The fiscal 1999 results of survey and research conducted for the establishment of solar cell performance evaluation and reliability evaluation methods are reported. In the development of a super high fidelity (broad spectrum) solar simulator for cell evaluation, a prototype was tested for performance evaluation, and initially set values were achieved. In the development of a large-area module evaluation technology, the radiation area was increased to be 1.0m times 1.0m large. Outdoor exposure tests continued at 5 sites in Japan, 3 sites in Australia, and 1 site in Oman, and analyses and databasing were carried out for the outputs of various types of solar cell modules. As for the problem of coloring of fillers which are module constituents, coloring in the U.S. was attributed to high temperature and intensive insolation, and in Austria to an oxidation inhibitor. In the development of a photo-accelerated degradation testing method for Si-based solar cells, application of the cycled illumination test was found feasible. In this test method, an amorphous silicon solar cell retains 70% of the initial Pmax value even after the passage of a period equivalent to 30 years. (NEDO)

Analysis and evaluation for practical application of photovoltaic power generation system. Research and development of elemental technologies for thin-type solar cells; Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Usugata takessho taiyo denchi jitsuyoka no tame no kaiseki hyoka

Energy Technology Data Exchange (ETDEWEB)

Sekikawa, T; Shimokawa, R; Yui, N; Takato, H; Takahashi, T; Ishii, K; Suzuki, E; Nagai, K; Kawanami, H; Tanimoto, J; Sakuta, H; Iwata, Y; Saito, N; Koyama, K; Sawada, S [Electrotechnical Laboratory, Tsukuba (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for analysis and evaluation for thin substrate polycrystalline solar cells. In order to analyze the structures of the grain boundaries in and interfaces with the cell substrate, and their effects on electrical activity, the photoluminescence (PL) measurement which enables spectroscopic analysis is applied to electromagnetically cast Si crystals. There are good correlations among PL luminous intensity, MBIC output and dislocation density for the grain boundary which contains many strains and serves as the dislocation source, because carriers in such a grain boundary easily disappear to reduce its luminous intensity at the band ends. Concrete scenarios for realizing thin-film silicon solar cells of high efficiency are presented, based on the analysis of the light-contained thin-film silicon solar cells of high output current, made in the previous year on a trial basis. An alumina substrate of high reflectivity is produced by the experiments of combining various devices. It is expected to realize high output current for the thin-film solar cells. 3 figs.

Research on fabrication technology for thin film solar cells for practical use. Survey on the commercialization analysis; Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on the technological trend, safety and latest technologies of thin film solar cells in fiscal 1994. As the fabrication technology for amorphous film solar cells, three-electrode plasma CVD was surveyed as fabrication method for high-mobility materials, and hydrogen radical CVD as fabrication method for high-photostable films. Current foreign and domestic reliability tests were surveyed for reliability evaluation of solar cells. In order to ascertain the performance, efficiency, physical properties and optimum structure of polycrystalline Si thin film solar cells, previously reported test results on physical properties such as carrier concentration, carrier lifetime and mobility of films were surveyed together with device simulation results. In addition, technologies for high-efficiency CuInSe2 system and CdTe system solar cells, technologies for cost reduction and mass production, and environmental influence were surveyed. Estimation of production costs for cell modules, and safety of thin film solar cells were also surveyed.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of next-generation thin-film solar cell module manufacturing technology - Development of CIS solar cell module manufacturing technology - Development of high-quality film enlargement technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu / kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims to establish a manufacturing process that enables both high-quality CuInSe{sub 2} (CIS) film solar cell enlargement and cost reduction and to develop a device structure which uses less heavy metal for the purposes of increasing the CIS thin-film solar cell size and efficiency and decreasing environmental impact. Several element technologies have been established for increasing the area of high-efficiency Cu(In, Ga)Se{sub 2} (CIGS) solar cells. Concerning the enlargement of the photoabsorption layer which is to assume the most important role, it is found that a high-quality CIGS film, which is near homogeneous though within a 10cm times 10cm area, is fabricated by an in-line vapor deposition method. As for dead area reduction and high-speed patterning, it is found that laser scribing works effectively in the patterning of the window layer and photoabsorption layer. As for reduction in the use of heavy metal, a high efficiency of 16.2% is attained in a cell not using a CdS film as expected in the case of a cell using a CdS film, this thanks to a CIGS film surface reforming technique. The technique of junction formation for CIGS solar cells is improved, and then a true efficiency of 18.5% is achieved. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction) (development of technology to manufacture micro light collection type solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

These technological developments are intended to demonstrate module efficiency of a micro light collection type solar cell of 15% by fiscal 2000, and obtain prospect on the module manufacturing cost of 140 yen per watt. Discussions given during fiscal 1997 are as follows: development has been performed on a design method to decide construction of a non-tracking micro light collection type module; in the state of cells being integrated on the module, the cells are arranged minutely and discretely, whereas, with discussions on a method to form them and assessment of the optical system as the main objective, single crystal silicon solar cells with a size smaller than 5 mm were fabricated on a trial basis; problems of forming micro cells by using the wafer cutting process were clarified; micro cells operating on light collection were fabricated trially to extract technological problems in light collecting operation and discuss technical problems in mass production; and development was performed on an evaluation method to analyze the cells' light collecting operation, and discussions were given on a method to estimate power generation amount from the light collection type modules. (NEDO)

Increase of body surface temperature and blood flow by theanine

International Nuclear Information System (INIS)

Hasegawa, Takeo; Noguchi, Kenichi; Ando, Satoshi

2002-01-01

Suntheanine (Taiyo Kagaku Co.: Theanine) is the trade name for L-theanine which is a unique amino acid found almost solely in tea plants, responsible for the exotictaste of green tea. We investigated the effects of relate to relaxation, improves the taste of processed foods, radiation sensitization, and increase of body surface temperature in vivo study. The results of the present study confirmed, (1) Suntheanine is incorporated into the brain and induces the emission of α -waves an induced of relaxation. (2) Body surface temperature and blood flow on skin were increased after administration of Suntheanine. (3) There was effects of radiation sensitization in whole body irradiation of X-rays after Suntheanine IP injection on C3H mice. (4) Acute toxicity, subacute toxicity and mutagen testconfirm the safety Suntheanine in this study

Solar cell. Taiyo denchi

Energy Technology Data Exchange (ETDEWEB)

Kamihara, T; Kondo, S; Mori, K [Matsushita Electric Industrial Co. Ltd., Osaka (Japan)

1990-10-23

This invention provides a solar cell having high resistance to strong incident light and high temperature preservability. Reason of performance degradation of the solar cell in high temperature atmosphere thermally diffuses at the boundary surface of the silicon with metal particles. The method of blocking this thermal diffusion is that the film thickness is of the level that the electrons can pass through the film by a quantum dynamical tunnel effect. In this invention, the construction is that a transparent substrate, a transparent electrode, a P-type amorphous silicon, an I-type amorphous silicon, silica and a collector electrode are sequentially laminated and receives the incident light, thus generating a voltage between the two electrodes. Thickness of silica film is 10-100 microns. Materials of the collector electrode are either single element or alloys of Cs, K, Na, Li, Ba, Mg, Cd, Ta, Al, Mo, Zr, Co, Fe, Cu, Ag, W, Cr, Au and Ni. 13 figs., 1 tab.

Solar cell. Taiyo denchi

Energy Technology Data Exchange (ETDEWEB)

Amemiya, S.; Hashimoto, Y. (Canon Inc., Tokyo (Japan))

1991-05-17

This invention provides a cheap solar cell having a transparent surface protective layer which satisfies both controversial properties such as high electroconductivity and high water repellency and also abated the reduction of photoelectric conversion. In other words, this invention provides a solar cell having a surface-protective layer prepared by lamination of a mixture of a transparent water-repelling resin and a transparent electroconductive oxide powder; said protective layer is grounded at the surface resistance of 1 {times} 10 {sup 10} ohm or less and the contact angle of water on said protective layer is 90 degrees or more. The transparent water-repelling resin used is a fliorine resin such as PTFE and a silicone resin such as organopolysiloxane. The transparent electrodonductive oxide powder used is tin oxide, indium oxide or a complex compound of ton oxide and antimony oxide. The solar cell of this invention can be used for a long time because the adhesion of the dusts and the contamination by dirty water are restricted. 1 fig., 1 tab.

Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (improvement of conversion efficiency of amorphous silicon solar cells after degradation); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (amorphous taiyo denchi no shoki rekkago koritsu kojo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development for qualitative improvement of a-Si solar cells after initial degradation in fiscal 1994. On the fabrication technology of light-stable a-Si films, the film formation method possible to control combined hydrogen by repetitive formation/treatment was developed. The obtained high-quality light-stable a-Si film was featured by low defect density in a wide optical band gap range, and defect density of nearly 3 {times} 10{sup 16}/cm{sup -3} after light irradiation. The light degradation rate of the cell where the a-Si film was applied to i layer was relatively stable by 10% or less. The a-Si/a-Si double-layer tandem cell fabricated by this technology produced a high conversion efficiency of 10.5%. By applying {mu}c-Si material to photoactive layer as narrow band gap material, the cell with optical sensitivity even in long wavelength ranges more than 1000nm was obtained. The a-Si/{mu}c-Si double-layer tandem cell produced an initial efficiency of 8.0% and an efficiency after degradation of 7.5%. 12 figs., 3 tabs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This research aims to achieve a conversion efficiency of 13% and a manufacturing cost of 140 yen/Wp with a 30cm times 30cm Cu(InGa)Se{sub 2}-based thin-film solar cell submodule. Ga and sulfur are combined and a film fabrication technology was developed which would improve on Voc. Concerning Ga, a laminated precursor layer was fabricated and evaluated, which comprised a Cu-25wt%Ga alloy layer and a Ga source which was a Cu-48%Ga alloy layer. Concerning sulfur, the vapor phase selenization temperature and the selenization retention time in an H{sub 2}Se gas atmosphere was allowed to vary for a change in Cu(InGa)Se{sub 2} calcopyrite crystallinity for the study of relations between the amount of sulfur taken in and the solar cell characteristics, and the relations were assessed by EPMA (electron probe microanalyzer). Technologies were developed for the fabrication of high-resistivity buffer layers by solution growth, for the fabrication of window layers (transparent, conductive ZnO film) by sputtering, and for their patterning. Submodules of a ZnO/Zn(O,S,OH)x/Mo structure were fabricated, 10cm times 30cm and 30cm times 30cm in size. The former achieved 12.5% in conversion efficiency, and the latter 11.6%. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of CIS solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihtsu (CIS taiyo denchi module no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on a technology to manufacture CIS-based thin film solar cells. This paper summarizes the achievements in fiscal 1999. In the research of a large-area light absorbing layer manufacturing technology, investigation was made on light absorbing layers in manufacturing sub-modules with a size of 30 cm times 30 cm. With regard to the temperature condition in the light absorbing layer forming process, it was found that the cooling rate affects particularly the adhesion in the connecting interface of the light absorbing layer and the Mo rear electrode layer. In addition, it was revealed that the sulfur take-in amount can be increases by extending the retention time at the sulfurizing temperature and by decreasing the temperature to turn the gas phase into selenium. In the research of elementary technologies to establish the mass production process, developments were performed on the high-resistance buffer layer manufacturing technology, the high-quality window layer film manufacturing technology, and the technology to manufacture rear electrode layer made of high-quality metals. In developing the patterning technology, two kinds of the existing patterning devices were modified and adjusted for patterning the substrates with a size of 30 cm times 30 cm. In addition, a processing device was installed in the conventional manually operated process for module finishing. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, development of technologies to manufacture next-generation thin film solar cells (development of technologies to manufacture CIS solar cell modules); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (CIS taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was made with an objective to achieve conversion efficiency of 13% in a 30 cm times 30 cm size submodule of a CIS-based thin film solar cell, and to develop a manufacturing technology that can achieve 140 yen/Wp. This paper describes the achievements attained during fiscal 1997. In fiscal 1997, based on the achievements reached during the previous year, a submodule with a size of 10 cm times 30 cm was fabricated for an attempt of improving the open voltage and short circuit current density. Simultaneously, the applicability thereof to a module with an area as large as 30 cm times 30 cm was evaluated. As a result of experimental discussions, enhancement in the open voltage was verified by increasing amount of Ga or sulfur, but it was not possible to achieve 600 mV or higher. In the research of component technologies to establish a mass production process, research and development was made on a high-resistance buffer layer film forming technology, a high-quality window layer film forming technology, a high-quality metallic rear electrode film forming technology, and patterning technologies. The outdoor exposure test was continued on laminated mini-modules with a size of 10 cm times 10 cm. (NEDO)

System optimization of solar hydrogen energy system based on hydrogen production cost. 2; Suiso seizo cost wo hyoka shihyo to shita taiyo suiso energy system no saiteki sekkei. 2

Energy Technology Data Exchange (ETDEWEB)

Ota, D; Yamagami, Y; Tani, T [Science University of Tokyo, Tokyo (Japan)

1996-10-27

In this paper, to evaluate the hydrogen production cost per unit volume, system optimization of solar hydrogen energy system is discussed. Based on the simulation of the I-V characteristics of amorphous Si (a-Si) photovoltaic array, the working point between the array and hydrogen generator was determined. The cost ratio of each design point was calculated. The optimum design points were 500 W/m{sup 2} for the single crystal Si system, and 600 W/m{sup 2} for the a-Si system. When the rating capacity of design point was constant, almost constant cost ratio was obtained independent of the type of photovoltaic cells. It was found that the photovoltaic cells can be fabricated in about 15% lower cost at maximum. It was also found that the optimum design point sifts to the lower insolation site due to reduction of the photovoltaic cell cost. Since the annual hydrogen generation quantity does not depend on the type of photovoltaic cells under the constant rating capacity of design point, hydrogen can be produced in lower cost by using photovoltaic cell of lower cost. 5 refs., 10 figs., 5 tabs.

Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for development of extra-high efficiency solar cells (fundamental research on extra-high efficiency III-V compound semiconductor tandem solar cells); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (chokokoritsu III-V zoku kagobutsu taiyo denchi gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Sekikawa, T; Kawanami, H; Sakata, I; Nagai, K; Matsumoto, K; Miki, K [Electrotechnical Laboratory, Tsukuba (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for development of extra-high efficiency III-V compound semiconductor tandem solar cells. Heteroepitaxial structures of compound semiconductors, such as GaAs, on silicon substrates are analyzed and evaluated by EXAFS, Raman and RHEED for the initial stage of the film growth and heterointerfaces. The device capable of in-situ observation of the growing surface structures during the period of heteroepitaxial film growth is introduced, to investigate the effects of rise-up and initial growth conditions on defects. The effects of atomic hydrogen on growth of a GaAs film on a silicon substrate are investigated from photoluminescence and solar cell characteristics, to confirm the effects of reducing defects. Heteroepitaxial growth of InGaP, which has the optimum band width for forming multi-junction silicon solar cells, on a silicon substrate is investigated, to find that an interfacial buffer layer is necessary to form a good film. 2 figs.

Development of Mo recycle technique from generator materials

Energy Technology Data Exchange (ETDEWEB)

Tanimoto, Masataka; Kurosawa, Makoto; Kimura, Akihiro; Nishikata, Kaori; Tsuchiya, Kunihiko [Japan Atomic Energy Agency, Oarai Research and Development Center, Oarai, Ibaraki (Japan); Kakei, Sadanori; Yoshinaga, Hideo [Taiyo Koko Corp., Ako Laboratory, Ako, Hyogo (Japan)

2012-03-15

The domestic {sup 99}Mo production by the (n,{gamma}) method is proposed in JMTR because of low amount of radioactive wastes and easy {sup 99}Mo/{sup 99m}Tc production process. For the development of domestic production, it is necessary to use the enriched {sup 98}MoO{sub 3}, which is very expensive, for high specific activity of {sup 99}Mo. A large amount of used PZC/PTC embraced {sup 98}Mo is also generated after the decay of {sup 99}Mo. JAEA and Taiyo Koko is proposed to recover molybdenum from the used PZC/PTC for an effective use of resources and reduction of radioactive wastes. Preliminary experiments of Mo recycling with un-irradiated MoO{sub 3} were carried out by the elution and sublimation methods. From the results, Mo recovery rate from the PZC/PTC was more than 95% by two kinds of methods. The prospects are bright for Mo recycle and reduction of radioactive wastes using these methods. (author)

Research on fabrication technology for thin film solar cells for practical use. Research on low-cost fabrication technology for large-area modules (production technology for amorphous silicon solar cell modules); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Daimenseki module no tei cost seizo gijutsu (amorphous taiyo denchi module seizo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on the fabrication technology of amorphous Si solar cell modules in fiscal 1994. (1) On process technology for prototype film substrate solar cells, an advanced preprocessing equipment for film substrates, stepping roll type film forming technology, and prototype submodules were studied. A conversion efficiency of 7.2% was achieved by use of the submodule formed in an effective region of 40 {times} 40cm{sup 2}. (2) On efficiency improvement technology for film substrate solar cells, p/i and n/i interfaces, forming condition for Ag film electrodes, film thickness of transparent electrode ITO, and optimum transmissivity were studied. (3) On technology for advanced solar cells, high-quality a-SiGe: H film, ion control in plasma CVD, and a-Si film formation by plasma CVD using SiH2Cl2 were studied as production technology of narrow gap materials. (4) On advanced two-layer tandem solar cells, the defect density in optical degradation of a-Si cells by reverse bias dark current was evaluated, and outdoor exposure data were analyzed. 4 figs., 1 tab.

Research on fabrication technology for thin film solar cells for practical use. Research on low-cost fabrication technology for large-area modules (CdS/CdTe solar cell modules); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Daimenseki module no tei cost seizo gijutsu (CdTe taiyo denchi module seizo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on the fabrication technology of CdS/CdTe solar cell modules in fiscal 1994. (1) On the fabrication technology for high-efficiency large-area solar cells, high-quality CdTe active layer was studied. S content taken in the active layer at sintering of CdTe decreased with an increase in formed CdTe, resulting in improvement of Voc of cells. (2) On the window layer with wide band gap, the solar cell superior in collection efficiency and photoelectric characteristics could be obtained using the newly developed mixed crystal film of Cd(1-x)Zn(x)S. (3) On the forming technology of large-area coating/sintering films, improvement of CdS film quality was studied by pressurized processing of printed CdS films. As a result, improvement of film density and light transmissivity was confirmed. (4) On the leveling process technology of CdTe films, smooth surface films were obtained by experiment using an equipment simultaneously exciting samples in all directions as one of uniform coating methods of films. 7 figs.

Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for extra-high efficiency solar cells (research on new concentrator modules); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (shingata shuko module)

Energy Technology Data Exchange (ETDEWEB)

Tanimoto, J; Sakuta, K; Sawada, S; Yaoita, A [Electrotechnical Laboratory, Tsukuba (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for analysis and evaluation of concentrator modules for extra-high efficiency solar cells. The outdoor exposure tests have been under way for 3 years for fluorescent plates, as part of the research program for development of materials and elementary techniques, and essentially no degradation has been observed by the perylene pigment test. Coupling of the fluorescent concentrator and solar cell units is investigated for the coupling position and method, to theoretically analyze geometrical coupling efficiency, where they are coupled at the bottom faces in consideration of easiness of module fabrication. It is demonstrated that a high coupling efficiency can be realized when the cell is sufficiently wide relative to thickness of the fluorescent plate. The coupling method is experimentally examined using transparent silicon gel. A prototype module having the same size as the commercial module (420mm by 960mm) is made on a trial basis, where a total of nine 20mm-thick cells are cut out of a single-crystalline silicon solar cell, 100mm by 100mm in size, and are connected to concentrators at the bottom faces. It shows 2.3 times increased output by the test using a large-area solar simulator. 2 figs.

Valuation of the quantity of electric output from photovoltaic generation system in case of PV module applied to installing to vertical direction; Taiyo denchi wo suichoku ni haichishita baai no hatsudenryo hyoka

Energy Technology Data Exchange (ETDEWEB)

Miyajima, K [Kansai Electric Power Co. Inc., Osaka (Japan)

1996-10-27

In general, it is most efficient and economical to install photovoltaic (PV) modules with proper slope. There are room spaces on the wall except ground or roof. The PV modules were installed on the vertical wall, to consider the compensative method for this weak point. When modules were installed vertically, there is an advantage that reflecting solar light as well as incident solar light can be utilized compared with the installation with slope. The PV modules were installed on the roof of building with inclination of 90{degree} facing to south using the roof material as a reflecting material (S90), and with inclination of 15{degree} facing to south (S15), to compare their output. The output ratio, S90/S15 was 0.42. When it was very fine, this value increased to 0.60. When using plated steel plate as the reflecting material, this value increased to 0.74, which provided 10 to 30% larger output than the roof material. From these results, about 50% of module output of S15 can be expected for S90. If receiving larger reflection, there would only a slight difference in the module output between S15 and S90. 3 figs., 1 tab.

Solar cell element, solar cell system, and illuminating system; Taiyo denchi soshi, taiyo denchi sochi oyobi shomei system

Energy Technology Data Exchange (ETDEWEB)

Oka, Y. [Toshiba Laytech Co. Ltd., Tokyo (Japan)

1997-12-12

This invention relates to provision of a photocatalytic film on the light intercepting surface for the solar cell substrate of the solar cell element, which transmits the lights in the wavelength region longer than ultraviolet, i.e. 410nm and longer wavelength lights, and intercepts the lights in ultraviolet wavelength region. This photocatalytic film retards the decrease in the light interception by the solar cell element, and simplifies the maintenance because it oxidizes and decomposes organic matters by the less than 410nm ultraviolet ray contained in the sunlight to prevent adhesion of organic substance on the light intercepting surface of the solar cell element. In addition, decomposed dirt composition is washed away to accelerate dirt removing performance by rain waterdrop adhesion on the intercepting surface when it is used outdoors. As to this photocatalytic film, the thickness from 0.01 to 0.5{mu}m is desirable, effective phtocatalytic activity can not be expected if the thickness is less than 0.01{mu}m, and transmission factor becomes smaller if the thickness exceeds 0.5{mu}m, producing no electromotive force. TiO2, ZnO, and FeTiO3 are used as such photocatalyst. 6 figs.

Research and development of photovoltaic power system. Characterization and control of surface/interface recombination velocity of crystalline silicon thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Silicon kessho usumaku ni okeru hyomen kaimen saiketsugo sokudo no hyoka to seigyo

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, H [Hokkaido University, Sapporo (Japan). Faculty of Engineering

1994-12-01

This paper reports the result obtained during fiscal 1994 on characterization and control of surface/interface recombination velocity of crystalline silicon thin films. To optimize design and manufacture of solar cells, it is necessary to identify correctly resistance factor (or doping) of bulk of materials, bulk minority carrier life, and recombination velocity on surface, passivation interface and electrode interface. A group in the Hokkaido University has been working since a few years ago on development of non-contact and non-destructive photo-luminescence surface level spectroscopy (PLS{sup 3}). A new non-contact C-V method was also introduced. Using these methods, basic discussions were given on possibility of separate measurements on surface/interface and bulk characteristics of solar cell materials. The PLS{sup 3} method and the non-contact C-V method were used for experimental discussions on evaluation of silicon mono-crystalline and poly-crystalline materials. Discussions were given on separate evaluations by using the DLTS method. 10 figs., 2 tabs.

Solar cell driving device. Taiyo denchi kudo sochi

Energy Technology Data Exchange (ETDEWEB)

Yamazaki, K [Shibaura Engineering Works Co. Ltd., Tokyo (Japan)

1991-01-24

In driving a motor by a solar cell, if the sun light is weak, the motor cannot be started because of the fact that the start-up current of the motor is more than the current needed for driving. In this invention, a current limiting circuit is placed between the solar cell and the load, whereby the current limitation by said limiting circuit is released when the detected voltage of the solar cell reached the value required for starting the load. The current limiting circuit uses a semiconductor element such as a thyrister and a transistor which general limits a current. Such a current limiting circuit is controlled by a voltage detecting circuit and is so constructed that the cell limitation is released when a specific preset volatge of the solar cell is reached. 2 figs.

Solar energy and ecosystem. ; Botanical factory which utilizes the solar energy. Taiyo energy to ecosystem. ; Taiyo energy wo riyoshita shokubutsu kojo

Energy Technology Data Exchange (ETDEWEB)

Okano, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1992-11-30

The present paper explains the present development status and future problem of botanical factory. As a lightening method in the factory, there are artificial light type, solar light type, and combined solar and artificial light type. Each of all the types has both advantages and disadvantages. Development history is explained of a combined solar and artificial light type botanical factory. An NFT (nutrient film technique) nutrient liquid cultivator was developed in order to stabilize the vegetable production. Further, the air conditioner was modified. Heat storage tank for the night power utilization use and simple duct type heat exchanger for the air conditioning use in the cultivating room underwent associated works for both the thermal insulation and prevention of water bakage, which resulted in heightening in efficiency of both floor area utilization and air conditioning. As for the botanical growth, spinach cultivated with a CO2 concentration which was about three times as high as that outdoors gave a 60% heavier harvest and hardly differed in nutritive quality from that cultivated in the farm. A continuous cultivation test in summer, 1990 resulted in about 224g/day and 250g/day in production rate per 1m[sup 2] of cultivation area for the spinach and lettuce, respectively, which makes the factory cultivation profitable by economizing both the construction and maintenance (expenses for light and fuel). Future problem is about how to put it to practical use. 5 refs., 4 figs., 1 tab.

Hybrid utilization of solar energy. Part 2. Performance analyses of heating system with air hybrid collector; Taiyo energy no hybrid riyo ni kansuru kenkyu. 2. Kuki shunetsu hybrid collector wo mochiita danbo system no seino hyoka

Energy Technology Data Exchange (ETDEWEB)

Yoshinaga, M; Okumiya, M [Nagoya University, Nagoya (Japan)

1996-10-27

For the effective utilization of solar energy at houses, a heating system using an air hybrid collector (capable of simultaneously performing heat collection and photovoltaic power generation). As the specimen house, a wooden house of a total floor area of 120m{sup 2} was simulated. Collected air is fanned into a crushed stone heat accumulator (capable of storing one day`s collection) or into a living room. The output of solar cell arrays is put into a heat pump (capable of handling a maximum hourly load of 36,327kJ/h) via an inverter so as to drive the fan (corresponding to average insolation on the heat collecting plate of 10.7MJ/hm{sup 2} and heat collecting efficiency of 40%), and shortage in power if any is supplied from the system interconnection. A hybrid collector, as compared with the conventional air collector, is lower in thermal efficiency but the merit that it exhibits with respect to power generation is far greater than what is needed to counterbalance the demerit. When the hybrid system is in heating operation, there is an ideal heat cycle of collection, accumulation, and radiation when the load is light, but the balance between accumulation and radiation is disturbed when the load is heavy. 4 refs., 8 figs., 3 tabs.

Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. Mie Prefectural Iidaka Senior/Junior High School has a 10kW solar cell system installed on the south-side roof of the school house. The system is linked to an in-house transformation station and the power generated by the system is supplied to the lighting and air-conditioning facilities in the building, and surplus if any is transmitted to the Chubu Electric Power Co., Inc., system. A field test is being conducted to determine if there are usability and safety in the 10kW system. A number of like systems are undergoing field tests, installed at a comprehensive technological training center of Kyushu Electric Power Safety Association, Kongo Gakuen Senior High School, Sakata Nursery School, Taiyo Daiichi Nursery School, Minami Kindergarten, Neyagawa Ishizu Old People's Home, Co-Op Living Konan, Factory Hishimeki, Tochigi Fuji Industries, Gamo-cho Hirabayashi Public Hall, Fukuoka Prefectural Culture Complex, Yatsusugi Forest Schooling Center, Osaka Prefectural Murano Water Purification Plant, Yamanashi Institute of Environmental Sciences, Utatsu-cho Town Office, Ginga Gakuen Junior High School, etc. (NEDO)

Voice Onset Time for the Word-Initial Voiceless Consonant /t/ in Japanese Spasmodic Dysphonia-A Comparison With Normal Controls.

Science.gov (United States)

Yanagida, Saori; Nishizawa, Noriko; Mizoguchi, Kenji; Hatakeyama, Hiromitsu; Fukuda, Satoshi

2015-07-01

Voice onset time (VOT) for word-initial voiceless consonants in adductor spasmodic dysphonia (ADSD) and abductor spasmodic dysphonia (ABSD) patients were measured to determine (1) which acoustic measures differed from the controls and (2) whether acoustic measures were related to the pause or silence between the test word and the preceding word. Forty-eight patients with ADSD and nine patients with ABSD, as well as 20 matched normal controls read a story in which the word "taiyo" (the sun) was repeated three times, each differentiated by the position of the word in the sentence. The target of measurement was the VOT for the word-initial voiceless consonant /t/. When the target syllable appeared in a sentence following a comma, or at the beginning of a sentence following a period, the ABSD patients' VOTs were significantly longer than those of the ADSD patients and controls. Abnormal prolongation of the VOTs was related to the pause or silence between the test word and the preceding word. VOTs in spasmodic dysphonia (SD) may vary according to the SD subtype or speaking conditions. VOT measurement was suggested to be a useful method for quantifying voice symptoms in SD. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. Mie Prefectural Iidaka Senior/Junior High School has a 10kW solar cell system installed on the south-side roof of the school house. The system is linked to an in-house transformation station and the power generated by the system is supplied to the lighting and air-conditioning facilities in the building, and surplus if any is transmitted to the Chubu Electric Power Co., Inc., system. A field test is being conducted to determine if there are usability and safety in the 10kW system. A number of like systems are undergoing field tests, installed at a comprehensive technological training center of Kyushu Electric Power Safety Association, Kongo Gakuen Senior High School, Sakata Nursery School, Taiyo Daiichi Nursery School, Minami Kindergarten, Neyagawa Ishizu Old People's Home, Co-Op Living Konan, Factory Hishimeki, Tochigi Fuji Industries, Gamo-cho Hirabayashi Public Hall, Fukuoka Prefectural Culture Complex, Yatsusugi Forest Schooling Center, Osaka Prefectural Murano Water Purification Plant, Yamanashi Institute of Environmental Sciences, Utatsu-cho Town Office, Ginga Gakuen Junior High School, etc. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research, development, and survey of crystalline solar cell evaluation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (kesshokei taiyo denchi hyoka system no kenkyu kaihatsu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the basic study of ultrahigh-efficiency cells, the technology of ribbon crystal growing is again attracting attention for shortage of Si material supply. The new technology and problems to solve for cost reduction for it are discussed. Concerning the bulk type crystalline Si which is a core material, recent trends are mentioned involving studies of basic substrate properties such as the photoabsorption coefficient and crystal defects for achieving higher efficiency, development of gettering and surface passivation technologies, enhancement of processing speeds, radiation concentration behavior, etc. Newly obtained findings about photodegradation are mentioned, and some remedial measures are described. Recent reports on the application of porous Si to solar cells are compiled. In connection with the development of low-cost quantity-production process technologies, a remarkable progress recently marked by polycrystalline Si solar cells is described. Furthermore, it is stated that new process technologies will be required in the fields of material refining, substrate manufacturing, and cell fabrication. A proposition is presented aiming at developing cell modules compatible with application systems and practicalizing modules that may be integrated with roofing materials. Reference is also made to surveys overseas. (NEDO)

Space photovoltaic power generation. Uchu taiyo hatsuden ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Kudo, I [Electrotechnical Laboratory, Tsukuba (Japan)

1993-07-20

Introduction is made of space photovoltaic power generation which is the ultimate clean energy source. This is a system to obtain electric energy from the solar cells placed on a geostatic orbit and transmit the power onto the earth by microwave. The US formulates a plan of placing 60[times]5GW power generation satellites to obtain 300GW power on the earth in 2000. As for the scale of space structure, the array of solar cells is dimensionally 10km[times]5km and the power transmitting antenna is 1km in diameter. The electric energy is amplified to microwave and power-transmitted by wireless onto the earth. The ground rectenna which receives it is dimensionally 10km[times]13km. The biggest difficulty consists in transportation of construction materials onto the orbit. In Japan, activity comprises three matters, which are research committee organized three years ago by the Agency of Industrial Science and technology, 10MW class model conceptually designed by the Institute of Space and Astronautical Science, and experiment conducted by Kyoto University on the power transmission by wireless. Pertaining to the research on the space power generation, the following two points are judged still unclarified: Reason for which the electric power companies did not apply the power transmission by wireless regarded as high in transmission efficiency. Influence of the microwave on the ionosphere and biosystem. 7 refs., 4 figs.

Protective material for solar cell; Taiyo denchiyo hyomen hogozai

Energy Technology Data Exchange (ETDEWEB)

Iimura, M.; Domoto, T. [Nitto Denko Corp., Osaka (Japan)

1998-02-03

The protective material for the solar cell of this invention consists of fluororesin containing from 1 to 20wt% titanium oxide particles with the particle size range from 1 to 1,000nm. Surface contamination of the protective material for the solar cell and deterioration of the adhesive are prevented when titanium oxide with particular particle size is contained in the fluororesin in a particular range as mentioned above. Titanium oxide has photocatalytic performance to decompose organic substances, and the surface protective material for the solar cell containing titanium oxide can decompose and remove dirt such as dust adhering the surface for preventing surface contamination. In addition, total light permeability can be maintained at high rate and the permeability of less than 350nm ultraviolet rays causing deterioration of the adhesive can be decreased if the particle size and content of titanium oxide are specified. Titanium dioxide of anatase type crystal structure is ideal as the titanium oxide. 1 tab.

Evaluation method of offensive odor. Shuki no hyoka hoho

Energy Technology Data Exchange (ETDEWEB)

Iwasaki, Y [The Tokyo Metropolitan Research Institute for Environmental Protection, Tokyo (Japan)

1991-06-01

As the evaluation method of offensive odor, two kinds of methods were outlined, a concentration measurement method for compounds emitting offensive odors and a sensory method by human olfactory organ. On the former, the method for measuring separately odors of twelve compounds controlled by the regulation act such as ammonia and hydrogen sulfide was outlined as well as the method for measuring odors of compound groups such as total reduced sulfur and total hydrocarbon. On the later, the evaluation scale of essential properties of odor such as quality, intensity, acceptability and pervasiveness was discussed. As typical sensory techniques, a scentometer, syringe method, odorless chamber method and olfactometer were outlined, and a triangle odor bag method widely used for the evaluation at present was described in detail which was developed to reduce demerits of a syringe method such as adsorption of odorants on a syringe surface. 24 refs., 6 figs., 3 tabs.

Evaluation technology of clothing comfortableness; Ifuku tekigosei hyoka gijutsu

Energy Technology Data Exchange (ETDEWEB)

Niwaya, H.

1999-10-26

Modern apparel industries are required to supply many kinds of products corresponding to various needs of consumers. Among consumers' needs, comfortableness to wear such as size-fitness is primarily important. To facilitate apparel industries, it is expected to develop a new technology of pattern designing of comfortable garment and measuring garment pressure distribution. Our research is aimed at developing technology that uses computer simulation to predict and evaluate wear comfort, including size suitability, without the need to actually sew up a garment. First, we developed a basic system to predict wearing silhouette, garment pressure, and ease looseness of the garment. Using this system, we carried on the following study. The 3-dimensional distributions of the garment pressure and ease looseness were reversely mapped on the paper pattern in order to indicate the preferable modification. The system was extended for several poses, e.g. twist, bend. From various parameters, we examined the factors of garment pressure and ease looseness. In addition, we selected the parameters for the size-fit indicators and investigated size-fit evaluation indicators. (author)

Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (high-efficiency III-V tandem solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (III-V zoku kagobutsu handotai taiyo denchi no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development of III-V compound semiconductor solar cells in fiscal 1994. (1) On development of epitaxial growth technology of lattice mismatching systems, the optimum structure of InGaAs strain intermediate layers was studied for reducing a dislocation density by lattice mismatching of GaAs layer grown on Si substrate and difference in thermal expansion coefficient. The effect of strain layer on dislocation reduction was found only at 250dyne/cm in strain energy. Growth of GaAs layers on the Si substrate treated by hydrofluoric acid at low temperature was attempted by MBE method. As a dislocation distribution was controlled by laying different atoms at hetero-interface, the dislocation density of growing layer surfaces decreased by concentration of dislocation at hetero-interface. (2) On development of high-efficiency tandem cell structure, tunnel junction characteristics, cell formation process and optimum design method of lattice matching tandem cells were studied, while thin film cell formation was basically studied for lattice mismatching tandem cells. 45 figs., 8 tabs.

FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for production of thin-film solar cells and low-cost, large-area modules (Development of technologies for high-reliability CdTe solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for production of low-cost, large-area modules of CdTe solar cells by the high-quality film-making process and high-function patterning, and the FY 1999 results are reported. The research program for the large-area TCO film-making technologies involves investigations on improvement of SnO{sub 2} film quality by the mist method and continuous film-making, which lead to continuous, stable production of 34 substrates of low resistance of 9.7{omega} on the average. The program for production of the large-area, thin-film CdS/CdTe solar cells involves production of TCO and CdS by the mist method, and patterning of the laminated TCO/CdS film by laser scribing. The CdTe film is formed by the atmospheric pressure CSS method, and treated with CdCl{sub 2} to improve its crystallinity. The CdTe film is patterned by sand blasting, and provided with the carbon and silver electrodes by screen printing, to complete the cell. The process is totally effected at the atmospheric pressure, needing no vacuum device. The CdTe solar cell assembly (130 cells connected in series, opening area: 5,413cm{sup 2}), fabricated on a trial basis, achieves a conversion efficiency of 10%. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost and large-area module manufacturing technologies, and new type amorphous solar cell manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to put amorphous solar cells for power use into practical use, research and development has been performed on a low-cost mass production technology for modules with large area and less deterioration using film substrates. This paper summarizes the achievements in fiscal 1999. In developing an efficiency enhancing technology, development of an a-Si/a-SiGe/a-SiGe triple cell structure was launched, and discussions were given on band gaps, film forming conditions, and film thickness. In developing a film forming speed enhancing technology, systematic experiments were performed, as well as theoretical analysis on the film forming mechanism in the plasma CVD process. In developing the process technology for film substrate solar cells, with regard to an a-Si production device of the multi-chamber arranged stepping roll system, six plasma CVD chambers were increased to 13 chambers to improve the electrode forming speed and such processes as drilling low-cost substrates, and laser patterning. In trial fabrication of a triple cell, a module in which one row of the SCAF cell is laminated provided an initial efficiency of 9.64%. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Manufacture of high-reliability CdTe solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The target is a low-cost CdS/CdTe solar cell of a large area (60cm times 90cm), the establishment of mass-production technologies for the cell, and the enhancement of production efficiency. A thin film formation technology of subjecting CdS film organic metal to pyrolysis is established, which reduces photoabsorption loss in the shortwave domain of wavelength of not longer than 500nm, reduces reflection loss in the film, and improves on short-circuit current density. Improvement is also achieved on CdTe film quality and junction quality by use of a proximity sublimation method in a vacuum, when a conversion rate of 16.0% (1cm{sup 2}) is attained which is the highest in the world. Based on the results of the above-said efforts, a 3.3mm-thick glass substrate is employed for CdTe film to develop into a 30cm times 60cm-large size, with the film thereon uniformly thick over a large area thanks to a normal pressure proximity sublimation method. Studies are made toward a process nearer to the ultimate product and, using the patterning technique, a 30cm times 60cm-large CdTe solar cell is tentatively built realizing a conversion rate of 9.8%. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of novel amorphous solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project intends to improve on large-area amorphous silicon solar cell performance and to develop high-throughput manufacturing technologies for a reduction in the cost of modules. A film substrate type amorphous solar cell structure of the serial connection type named SCAF (series-connection through apertures formed on film) is contrived. Under this method, film formation using a stepping roll system newly developed for glass substrates may be applied, and the number of manhours required is allowed to be less than under conventional serial connection forming processes. The new technique is characterized in that serial connections are established via through-holes provided in plastic substrates. Making use of the technology, progress is attained in the development of high-throughput process technology for film substrate type amorphous solar cells and of efficiency enhancement technology. In fiscal 1997, an electron beam unit for plasma generation aiming at the elucidation of reaction processes in plasma was introduced, and technologies based on the equilibrium discharge technique were developed enabling high-speed a-Si film formation without degradation in film quality. The effect of trace boron addition to the tandem cell bottom I layer was investigated, and a stabilization rate of 8.05% was achieved using a 40cm times 80cm large SCAF cell. In fiscal 1998, endeavors were exerted for similar developments. (NEDO)

Evaluation technology of human behavior cognition; Ningen kodo ninchi hyoka gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For human engineering and improvement of the living environment, the evaluation technology of human behavior cognition was studied. For the future reformation and creation of economic structure, the following are required: establishment of safe and affluent communities, further improvement of the safety and harmonious balance of people, lives and society, and R & D close to people and social needs. Introduction of Product Liability law and a fail-safe concept are examples of such efforts. However, since many accidents are found in the human society, the relation between human errors and human characteristics should be studied in detail. The cognitive science of human behavior is an objective evaluation technology from the viewpoint of human being, object, environment and society. Based on these social and technological background, the feasibility of the evaluation technology is studied, and the future trend and skeleton of this project are clarified. The domestic and foreign trends of technologies concerned are thus surveyed, and the important points, features, skeleton and ripple effect of the technology are summarized. 500 refs., 70 figs., 5 tabs.

Coloration and bleaching mechanism of niobium oxide electrochromic thin films; Sanka niobu electromic usumaku no chakushoshoku mechanism

Energy Technology Data Exchange (ETDEWEB)

Yoshimura, K; Miki, T; Tazawa, M; Jin, P; Igarashi, K; Tanemura, S [National Industrial Research Institute of Nagoya, Nagoya (Japan)

1997-11-25

In order to search for the coloration and bleaching mechanism of niobium oxide, considerations were given on optical properties and electron conditions in niobium oxide thin films (glass plates as substrates coated with ITO) prepared by using the reactive DC magnetron sputtering process. The films were so grown that their thickness will all be 100 nm to facilitate data comparison. Coloration and bleaching of the grown test films were conducted by cyclic voltammetry. Electron spectra were measured by using XPS, and electron energy was analyzed. Coloration of niobium oxide occurs as a result of change in valency electron state from an Nb {sup 5+} state to an Nb {sup 4+} state, while change in the XPS spectra also corresponds with the above change. However, the XPS spectra differ greatly between crystalline samples and amorphous samples. The coloration and bleaching mechanism of the crystallized Nb2O5 film can be explained by a reaction formula similar to that for WO3. However, with regard to the amorphous Nb2O5 film, an independent reaction involving water in the film seems to occur together with the same reaction as in the crystallized film. 9 refs., 5 figs.

Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (research and development of composite materials on solar cells under microgravity environment); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (bisho juryoku kankyo wo riyoshita taiyo denchiyo zairyo kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of composite materials for solar cells under microgravity environment in fiscal 1994. (1) On a thin film capillary method, 26 experiments of GaSb thin film crystal growth were conducted using the especially prepared high-accuracy electric furnace under microgravity. The wettability of thin film crystals was improved by refining equipment. Rhombus crystal planes and large crystal grains were observed in GaSb thin film crystals prepared under microgravity. (2) On a liquid phase method, the effect of the gravity on crystal structure and grain morphology was studied for synthesis of CdS fine grains. (3) On technological development of composite materials, the solidification experiment of Cu-In-Se melt was conducted under short time microgravity of 10{sup -4}g for 10 sec. As a result, more uniform texture and more high crystallinity were obtained under microgravity, and In in melt was concentrated by surface tension effect. It was suggested that high-quality CIS thin films will be obtained by Se doping into Cu-In composite films under microgravity environment.

Technological development for super-high efficiency solar cells. Technological development for super-high efficiency singlecrystalline silicon solar cells (super-high efficiency singlecrystalline Si solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (chokokoritsu tankessho silicon taiyo denchi cell no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development of super-high efficiency singlecrystalline silicon solar cells in fiscal 1994. (1) On development of high-performance light receiving layer, the fine electrode for receiving surfaces was designed to reduce serial resistance, and the high-quality oxide passivation film was studied to reduce surface recombination velocity. (2) On development of forming technology of back heterojunction, the high-quality cell with B-doped fine crystalline Si film on its back was studied by heat treatment of the fine crystalline Si film, and the cell structure with high back reflectance of light was also studied. (3) On analysis for high-efficiency cells, the relation between the back recombination velocity at the interface between p-type substrate and back passivation film, and the internal collection efficiency as probe light was injected from the back, was calculated by numerical simulation. As a result, the cell back recombination velocity could be evaluated by measuring the spectral internal collection efficiency to back injection. 15 figs., 6 tabs.

Proceedings of JSES/JWEA Joint Conference (1997); Taiyo/Furyoku energy koen ronbunshu (1997)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-25

The paper includes 114 papers made public in the JSES/JWEA Conference held in Toyohashi University of Technology on November 28 and 29, 1997. In the field of the photovoltaic power system, included were papers titled Photovoltaic system at Nagaoka College of Technology, Generation characteristics of photovoltaic power generation equipment at TEPCO R and D Center. As to solar cell modules, Change of photovoltaic module conversion efficiency with the environmental factors in different site, Change of environmental factors in different site which effect the conversion efficiency of photovoltaic module, etc. In relation to the solar hot water system, Investigation of the simulation for the solar DHW system by TRNSYS, etc. Concerning the hydrogen production, Experimental study of hydrogen generation by water electrolysis using solar battery, etc. About solar houses/buildings, Study on indoor pollution by microbes grown in a solar house in Tokyo, etc. Besides, papers in the following fields were included: wind power, wave power, hybrid systems, space heating/cooling and air conditioning, solar energy collection, heat pumps, etc

Prospects to solar energy power generation in space. Uchu taiyo hatsuden eno tenbo

Energy Technology Data Exchange (ETDEWEB)

Kudo, I. (Electrotechnical Laboratory, Tsukuba (Japan))

1993-05-01

Solar energy power generation in space uses large arrays of solar cells developed on a geosynchronous orbit to obtain electric energy, which is transmitted to the earth using microwaves. The idea had already been advocated in 1968, which was followed a decade later by joint discussions done by NASA and DOE. The concept intended to take care of the U.S. power demand by using 60 power plant satellites, each having an output of 5 GW. This expanse of the scale, regarded reasonable even today, calls for the solar cell arrays in space spreading over an area of 10 km [times] 5 km if silicon solar cells with a conversion efficiency of 15% are used, and rectenna on the ground (a received wave converting facility) forming an ellipse of 10 km [times] 13 km (assuming a location at the north latitude of 36[degree]). Although there are a number of problems in the idea such as transportation means to lift construction materials into the space and effect of microwaves on the ionosphere and the ecosystems, the Agency of Industrial Science and Technology organized a 'committee for investigating and studying the space power generation systems' in the fiscal year 1991, and has been moving discussions forward since then. 7 refs., 5 figs.

Proceedings of JSES/JWEA Joint Conference (1996); Taiyo/furyoku energy koen ronbunshu (1996)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-10-27

The proceedings has 10 papers on photovoltaic power systems, 9 on characteristics of solar cells, 5 on residential use photovoltaic power systems, 3 on solar cars, 6 on solar hybrids, 9 on solar energy storage, 5 on passive solar energy, 4 on power generation/hydrogen production, 5 on wind power, 5 on wind power/wave power, 7 on insolation/meteorology, 3 on heat collection, 9 on air cooling/conditioning, 4 on hot water supply systems, 6 on heat pumps, and 5 on the application to biotechnology. As a special lecture, `The development of a new electric vehicle, EcoVehicle, and the environment` was given by National Institute for Environmental Studies. This was taken notice of as a new concept of electric vehicles. Namely, technologies were collected which are useful for improving electric vehicle performance, and technologies which can use due to the electric vehicle were adopted. The vehicle was so designed as to make good use of characteristics of electric vehicles. As a result, born was `EcoVehicle,` a two-seater having a car width of 1.2m and a car length of 3.3m. The vehicle was installed with polycrystalline solar cells on the roof and spoiler, and has a maximum output of 60W. It can travel 1000km per year when assuming annual duration of sunshine to be 1800 hours.

Present condition and the future of photovoltaic generating systems. Part 5. Future perspective of photovoltaic power systems; Taiyo hikarihatsuden system no genjo to shorai. 5. Taiyo hikarihatsuden system no shorai tenbo

Energy Technology Data Exchange (ETDEWEB)

Horigome, T

1994-12-20

In this paper, as the future perspective of photovoltaic power systems, the establishment of the legal environment for the popularization of the photovoltaic power systems in large amounts and the future prediction of the popularization of power generation are described. Specially the following grand ideas are introduced: building in high seas regeneratable energy transformation plants with solar energy as the main energy, generating combined power of photovoltaic, solar heat, wave and temperature difference of the sea water, biomass, solar-bio power generating without CO2 exhaustion, building hard solar plants to produce electricity, hydrogen, methanol and fresh water from regeneratable energy, and breeding fish, shells and see weed in the sea pasture land under the plants, which are the so called `Energy sea pasture high breed plants (REPO Plan)` and also space power generating i.e. setting up special satellites for solar power generation in synchronous orbits, generating power through solar batteries or solar heat and then transmitting it to the earth through microwave. 12 refs., 4 figs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of high-reliability CdS/CdTe solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Cost reduction for the above-named solar cells is the aim of this effort. On the basis of the results of past studies, a technology is established of fabricating a thin CdS film by subjecting a CdS film to organometal pyrolysis, and this brings about a decrease in photoabsorption loss in the range of waves shorter than 500nm and a decrease in in-film reflection loss for an increase in short-circuit current density. A proximity sublimation method is used for CdTe film fabrication, which improves on film quality and film adhesion. These efforts result in the achievement of a conversion efficiency of 16.0% which is the highest in the world. Studies are promoted in a process nearer to the ultimate form, and a 30cm times 60cm large CdTe solar cell is fabricated on the basis of a patterning technique, and the product attains a conversion efficiency of 9.8%. In fiscal 1998, studies center about the establishment of a film fabrication process for a medium-are substrate and about the enhancement of its conversion efficiency, and facilities capable of dealing with large-area substrates are introduced and operated. In a typical achievement, a CdTe solar cell is experimentally fabricated in a process which is wholly under normal pressure, and the product with an aperture area of 1376cm{sup 2} exhibits a conversion efficiency of 10.5% according to JQA (Japan Quality Assurance Organization). (NEDO)

New Sunshine Project FY 1996 report on the results of development of photovoltaic power generation system commercialization technologies. Research on commercialization of the technologies for production of thin-film photovoltaic cells (Development of fabrication technologies of high-quality CuInSe{sub 2}-based thin-film solar cells); 1996 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu (kohinshitsuka gijutsu (CuInSe{sub 2} taiyo denchi seizo no gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Described herein are the FY 1996 results of development of fabrication technologies for high-quality CuInSe{sub 2}-based photovoltaic cells. The Cu-Ga alloy/In-stacked precursor film is prepared for production of the high-quality thin-film absorber applicable to large-area module fabrication, and selenized by the vapor-phase selenization in a H{sub 2}Se gas atmosphere to produce the thin light-absorbing film in which In and Ga are present at graded concentrations. Increasing Ga alloy content in the CIGS-based thin-film photovoltaic cell fails to widen the forbidden band and improve V{sub oc}, and further optimization works are needed. The method is developed for production of thin-film buffer layer of sulfur-containing Zn compound which can give the cell characteristics equivalent to those of CdS generally used for CIS-based thin-film photovoltaic cell. It is clarified that the photovoltaic cell characteristics can be improved by use of a transparent electroconductive ZnO film of stacked structure, produced by a combination of RF sputtering and DC sputtering. For the patterning technologies necessary for forming series connection on a mini-module, the laser scribing method is applicable to the metal base-electrode, and the mechanical scribing method to the light absorber and window layer. (NEDO)

Geothermal reservoir assessment manual; 1984-1992 nendo chinetsu choryusou hyoka shuhou manual

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-02-01

A geothermal reservoir assessment manual was prepared for the promotion of the development of geothermal power generation, based on the results of the 'geothermal reservoir assessment technique development project' implemented during the fiscal 1984-1992 period and on the results of surveys conducted in Japan and abroad. Of the geothermal systems generally classified into the steam dominant type and the hot water dominant type, encounters with the steam dominant type are but seldom reported. This manual therefore covers the hot water dominant type only. In addition to the explanation of the basic concept and the outline of geothermal reservoirs, the manual carries data necessary for reservoir assessment; geological and geophysical data analyses; geochemistry in reservoir assessment; data of underground logging and of fuming; conceptual models; simulators and models for reservoir simulation; natural-state simulation, history-matching simulation, and reservoir behavior predicting simulation; case history (modeling of a geothermal reservoir prior to exploitation), references, and so forth. (NEDO)

Geothermal reservoir assessment manual; 1984-1992 nendo chinetsu choryusou hyoka shuhou manual

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-02-01

A geothermal reservoir assessment manual was prepared for the promotion of the development of geothermal power generation, based on the results of the 'geothermal reservoir assessment technique development project' implemented during the fiscal 1984-1992 period and on the results of surveys conducted in Japan and abroad. Of the geothermal systems generally classified into the steam dominant type and the hot water dominant type, encounters with the steam dominant type are but seldom reported. This manual therefore covers the hot water dominant type only. In addition to the explanation of the basic concept and the outline of geothermal reservoirs, the manual carries data necessary for reservoir assessment; geological and geophysical data analyses; geochemistry in reservoir assessment; data of underground logging and of fuming; conceptual models; simulators and models for reservoir simulation; natural-state simulation, history-matching simulation, and reservoir behavior predicting simulation; case history (modeling of a geothermal reservoir prior to exploitation), references, and so forth. (NEDO)

Method of evaluating the surface color of concrete; Concrete hyomenshoku hyoka shuho

Energy Technology Data Exchange (ETDEWEB)

Kondo, Y; Kotani, K; Imadate, F; Ito, N; Watanabe, K [Kajima Corp., Tokyo (Japan)

1995-12-20

As a part of the evaluation of landscape of civil engineering structures, a method was studied for quantitative evaluation of surface color and color hue of the exposed concrete. The surface colors of concrete structures constructed at more than one sites were measured using a colorimeter and were statistically processed. The colorimeter can measure colors by irradiating the standard light onto the surface of the object and dividing the reflection light into ingredients, lightness L and color phase a and b in the CIELAB equal color space. The L/a/b measuring data were plotted which were obtained from 2010 measuring surfaces of 49 structures at 7 construction sites. As for the surface color of concrete, it was found that ingredient L measured by the colorimeter reacts on variations of color very sensitively and agrees well with the trend of evaluation by eyes. Namely, human being senses the difference of concrete color mainly from the difference in lightness and senses the difference as the color hue. Further, using the neural network, an evaluation method was established which was the same as the human sense. 1 ref., 8 figs., 3 tabs.

Interim report on research and development of super heat pump energy accumulation system by the evaluation working group; Super heat pump energy shuseki system hyoka work group chukan hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

The evaluation working group of the Large-scale Energy-saving Technology Research and Development Promotion Council has made an interim evaluation of the results obtained so far by the R and D project for the super heat pump energy accumulation systems. The working group evaluates the bench plant operation test results comprehensively, covering technical, economic and social aspects, and R and D promotion methodology. The working group has concluded that a significant technological break-through is made for the super high performance compression heat pumps, and the technological groundwork is now established for the future pilot system. For the chemical heat storage technologies, it is concluded that system feasibility is demonstrated, and the technological groundwork for the future development is established. The super heat pump is evaluated to potentially realize significant economic superiority over the conventional devices both in the domestic and industrial areas, and to be highly rated potentially in the areas of energy-saving, power load leveling and environmental preservation. (NEDO)

28th Solar Energy Promotion Committee Meeting - 3rd Solar Cell Liaison Meeting. Report for fiscal 1990; Dai 28 kai taiyo energy suishin iinkai dai 3 kai taiyo denchi renrakukai. 1980 nendo hokoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-14

The above events took place in Tokyo in the period May 14-17, 1991, when a total of 89 essays were presented. In relation with the thin film/a-Si systems, 55 presentations were given, which were 'Novel preparation technique termed Chemical Annealing for making a-Si:H with a rigid and stable Si-network,' 'Interface characteristics of a-Si:H films prepared by VHF (very high frequency) plasma CVD (chemical vapor deposition),' 'Preparation of amorphous superlattices by continuous method and characterization of the interface,' etc. In relation with the thin film/compound systems, 8 presentations were given, which were 'Preparation of CuInSe{sub 2} solar cells by selenization method,' 'Deposition of CuInSe{sub 2} films by ICB (ionized cluster beam) technique and their optical characterization,' 'Large-area CdS/CdTe solar cells,' etc. In relation with the crystal/compound systems, 8 presentations were given, which were 'Lattice strain relaxation processes in GaAs grown on Si,' 'Optical transmission studies of tandem solar cells,' etc. In relation with the crystal/Si systems, 18 presentations were given, which were 'Effect of electric field on effective minority carrier lifetime,' 'Computer analysis of surface recombination velocity for high efficiency crystalline silicon solar cells,' etc. (NEDO)

31st Solar Energy Promotion Committee Meeting - 6th Solar Cell Liaison Meeting. Report for fiscal 1993; Dai 31 kai taiyo energy suishin iinkai dai 6 kai taiyo denchi renrakukai (1993 nendo hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-04-25

The above-named events were convened in the period of April 25-28, 1994, when a total of 71 presentations were given on research achievements. Presented in the session on thin film systems were 21 essays concerning the low cost manufacturing technology of low-area modules, development of film substrate a-Si solar cells, etc. Discussed at the symposium were the 'Autonomous development of photovoltaic power generation' and 'Practical application and research and development.' Presented in the session on crystalline Si systems were 17 essays concerning real-time observation of epitaxial growth using STM (scanning tunneling microscope), research on single crystal silicon manufacturing technology, etc. Discussed in the session on international cooperation was 'How international joint research should be.' Presented in the session on systems were 11 essays including the research and development of photovoltaic modules integrated with construction materials. Presented in the session on III-V group systems were 7 essays including the development of crystallized compound solar cell technology. Presented in the session on chalcopyrite II-VI group systems were 9 essays including the development of large area CdS/CdTe solar cell. (NEDO)

28th Solar Energy Promotion Committee Meeting - 3rd Solar Cell Liaison Meeting. Report for fiscal 1990; Dai 28 kai taiyo energy suishin iinkai dai 3 kai taiyo denchi renrakukai. 1980 nendo hokoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-14

The above events took place in Tokyo in the period May 14-17, 1991, when a total of 89 essays were presented. In relation with the thin film/a-Si systems, 55 presentations were given, which were 'Novel preparation technique termed Chemical Annealing for making a-Si:H with a rigid and stable Si-network,' 'Interface characteristics of a-Si:H films prepared by VHF (very high frequency) plasma CVD (chemical vapor deposition),' 'Preparation of amorphous superlattices by continuous method and characterization of the interface,' etc. In relation with the thin film/compound systems, 8 presentations were given, which were 'Preparation of CuInSe{sub 2} solar cells by selenization method,' 'Deposition of CuInSe{sub 2} films by ICB (ionized cluster beam) technique and their optical characterization,' 'Large-area CdS/CdTe solar cells,' etc. In relation with the crystal/compound systems, 8 presentations were given, which were 'Lattice strain relaxation processes in GaAs grown on Si,' 'Optical transmission studies of tandem solar cells,' etc. In relation with the crystal/Si systems, 18 presentations were given, which were 'Effect of electric field on effective minority carrier lifetime,' 'Computer analysis of surface recombination velocity for high efficiency crystalline silicon solar cells,' etc. (NEDO)

29th Solar Energy Promotion Committee Meeting - 4th Solar Cell Liaison Meeting. (Report for fiscal 1991); Dai 29 kai taiyo energy suisuin iinkai dai 4 kai taiyo denchi renrakukai. 1991 nendo hokoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-04-21

The above-named events took place in Tokyo in the period of April 21-24, 1992, and a total of 55 essays were presented. Presented in the session of the thin-film/a-Si systems were 27 essays, which were 'Light-induced degradation and its mechanism in a-Si:H and its multilayers,' 'Light-induced ESR (electron spin resonance) in a-Si{sub 1-x}N{sub x}:H,' 'Distribution of hydrogen surrounding light-induced defects,' 'Equilibration temperature and hydrogen diffusion in a-Si:H,' etc. Presented in the session of the thin-film compound systems were 6 essays, which were 'Local structure studies of CuInSe{sub 2} thin films,' 'Characterization of CuInSe{sub 2} bilayer films fabricated by ICB (ionized cluster beam) techniques,' etc. Presented in the session of the crystal compound systems were 7 essays, which were 'heteroepitaxy of In{sub x}Ga{sub 1-x}As/GaAs,' 'cell efficiency calculation for optimization of cell structure,' etc. Presented in the session of the crystal/Si systems were 15 essays which were 'Preparation of textured AR film,' 'Development of amorphous/thin film polycrystalline silicon tandem cell,' 'Development of high efficiency polycrystalline silicon thin-film solar cells,' 'Production of SOG (spin on glass)-Si from metallic grade silicon,' etc. (NEDO)

29th Solar Energy Promotion Committee Meeting - 4th Solar Cell Liaison Meeting. (Report for fiscal 1991); Dai 29 kai taiyo energy suisuin iinkai dai 4 kai taiyo denchi renrakukai. 1991 nendo hokoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-04-21

The above-named events took place in Tokyo in the period of April 21-24, 1992, and a total of 55 essays were presented. Presented in the session of the thin-film/a-Si systems were 27 essays, which were 'Light-induced degradation and its mechanism in a-Si:H and its multilayers,' 'Light-induced ESR (electron spin resonance) in a-Si{sub 1-x}N{sub x}:H,' 'Distribution of hydrogen surrounding light-induced defects,' 'Equilibration temperature and hydrogen diffusion in a-Si:H,' etc. Presented in the session of the thin-film compound systems were 6 essays, which were 'Local structure studies of CuInSe{sub 2} thin films,' 'Characterization of CuInSe{sub 2} bilayer films fabricated by ICB (ionized cluster beam) techniques,' etc. Presented in the session of the crystal compound systems were 7 essays, which were 'heteroepitaxy of In{sub x}Ga{sub 1-x}As/GaAs,' 'cell efficiency calculation for optimization of cell structure,' etc. Presented in the session of the crystal/Si systems were 15 essays which were 'Preparation of textured AR film,' 'Development of amorphous/thin film polycrystalline silicon tandem cell,' 'Development of high efficiency polycrystalline silicon thin-film solar cells,' 'Production of SOG (spin on glass)-Si from metallic grade silicon,' etc. (NEDO)

31st Solar Energy Promotion Committee Meeting - 6th Solar Cell Liaison Meeting. Report for fiscal 1993; Dai 31 kai taiyo energy suishin iinkai dai 6 kai taiyo denchi renrakukai (1993 nendo hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-04-25

The above-named events were convened in the period of April 25-28, 1994, when a total of 71 presentations were given on research achievements. Presented in the session on thin film systems were 21 essays concerning the low cost manufacturing technology of low-area modules, development of film substrate a-Si solar cells, etc. Discussed at the symposium were the 'Autonomous development of photovoltaic power generation' and 'Practical application and research and development.' Presented in the session on crystalline Si systems were 17 essays concerning real-time observation of epitaxial growth using STM (scanning tunneling microscope), research on single crystal silicon manufacturing technology, etc. Discussed in the session on international cooperation was 'How international joint research should be.' Presented in the session on systems were 11 essays including the research and development of photovoltaic modules integrated with construction materials. Presented in the session on III-V group systems were 7 essays including the development of crystallized compound solar cell technology. Presented in the session on chalcopyrite II-VI group systems were 9 essays including the development of large area CdS/CdTe solar cell. (NEDO)

32nd Solar Energy Promotion Committee Meeting - 7th Solar Cell Liaison Meeting. Report for fiscal 1994; Dai 32 kai taiyo energy suishin iinkai dai 7 kai taiyo denchi renrakukai (1994 nendo hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-24

The above-named events were convened in the period of April 24-27, 1995, when a total of 77 presentations were given on research achievements. In the session on thin type Si polycrystalline systems, 12 essays were presented concerning the thermodynamics of phosphorus and titanium in silicon, etc. In addition, a discussion was held on the 'Technological tasks remaining to be discharged toward industrialization.' In the session on thin film polycrystalline silicon systems, 5 essays were presented and 'Technological tasks related to thin film polycrystalline silicon solar cell' was discussed. In the session on ultrahigh efficiency Si systems, 5 essays were presented and 'Tasks related to the development of ultrahigh frequency single crystal Si solar cell' was discussed. At the symposium, 'Adoption of new energy to be accelerated following the formulation of the New Energy Introduction Guidelines' and 'Outlook for thin film solar cell practical application' were taken up. Various essays were presented and a discussion was held in each of the other sessions on ultrahigh efficiency III-V group systems, thin film chalcopyrite/II-VI group systems, international collaboration, matters related to systems, and thin film a-Si systems. (NEDO)

32nd Solar Energy Promotion Committee Meeting - 7th Solar Cell Liaison Meeting. Report for fiscal 1994; Dai 32 kai taiyo energy suishin iinkai dai 7 kai taiyo denchi renrakukai (1994 nendo hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-24

The above-named events were convened in the period of April 24-27, 1995, when a total of 77 presentations were given on research achievements. In the session on thin type Si polycrystalline systems, 12 essays were presented concerning the thermodynamics of phosphorus and titanium in silicon, etc. In addition, a discussion was held on the 'Technological tasks remaining to be discharged toward industrialization.' In the session on thin film polycrystalline silicon systems, 5 essays were presented and 'Technological tasks related to thin film polycrystalline silicon solar cell' was discussed. In the session on ultrahigh efficiency Si systems, 5 essays were presented and 'Tasks related to the development of ultrahigh frequency single crystal Si solar cell' was discussed. At the symposium, 'Adoption of new energy to be accelerated following the formulation of the New Energy Introduction Guidelines' and 'Outlook for thin film solar cell practical application' were taken up. Various essays were presented and a discussion was held in each of the other sessions on ultrahigh efficiency III-V group systems, thin film chalcopyrite/II-VI group systems, international collaboration, matters related to systems, and thin film a-Si systems. (NEDO)

Achievement report for fiscal 1997 on developing practical application technology for photovoltaic power generation systems under the New Sunshine Project. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, and development of technologies to manufacture new type amorphous solar cells; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, shingata amorphous taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Development will be made on high-performance a-solar cells as part of developing practical application technology for a-solar cells for electric power use. Development will be also made on a low-cost process technology. This paper describes the achievements attained during fiscal 1997. Quality improvement has been realized by using a high RF power hydrogen dilution process on a-Si films for front cells of lamination type cells. Four times faster film forming speed was obtained even by using the VHF plasma CVD process, with film quality equivalent to those made by using the conventional RF process maintained. By optimizing the light enclosing construction, the short circuit current was enhanced by over 20%. Discussions were given on forming homogenous a-Si films by optimizing the conditions for forming films on large-area substrates, which resulted in forming film of 30 cm times 40 cm size with good homogeneity at a film forming speed three times faster than the conventional speed. A surface electrode was formed successfully with good uniformity on a substrate with a size of 60 cm times 90 cm. Productivity greater by over three times the conventional productivity was achieved in patterning of transparent electrodes by using high-output laser. Simultaneous and collective patterning and very small and long size collective patterning were realized in a-Si film selection patterning by using the plasma CVD process. (NEDO)

NEDO Forum 2000. Proliferation of information and achievements, and evaluation session (toward achievement evaluation and information signaling); Joho seika no fukyu to hyoka session. Seika no hyoka to joho hasshin ni mukete

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The following themes were presented at the present session: (1) fundamental survey on evaluation of projects, (2) the IEA information exchange agreement project and information providing activities by NEDO, (3) the NEDO technological information database, (4) the NEDO's intelligent property releasing institution and utilization of the patent database, (5) examples of successful utilization of NEDO patents (mask producing equipment by means of electronic beam depiction), and (6) special lectures (the current status of information network technologies and their new development in the future). Item (1) describes a method to evaluate reasonability of decision makings at each time point around project management, in which time divisions are set, and compared with requirements in each time. It also describes discussions on the reasonability thereof. As the execution agreement with IEA for energy technology data exchange (ETDE), Item (2) introduces the IEA energy and environment technology information (a project by Centre for the Analysis and Dissemination of Demonstrated Energy Technology (CADDET) and a project of Greenhouse Gas Technology Information Exchange (GREENTIE)), as well as the execution agreement to establish IEA coal researches, and the NEDO information providing activities. Item (3) introduces the NEDO project information, NEDO achievement report, CADDET database, and GREENTIE database as the databases provided by the NEDO Information Center. (NEDO)

FY 1977 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Solar thermal power generation systems); 1977 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyo netsu hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at surveys and researches on operation, economic efficiency and performance evaluation of solar thermal power generation systems, and test methods, e.g., for aging the materials for their devices, in order to establish the methods for evaluating their performance. For operation of solar thermal power generation systems, a feasible system is a hybrid with another system, e.g., thermal power or nuclear system. For economic efficiency, heat-storage capacity will be based on power generation for around 4 hours a day for a solar system to be installed in Japan. The construction and light/heat-collecting costs should be reduced to around 300,000 yen/kW and 13,000 to 21,000 yen/m{sup 2}, respectively, in order to keep the power generation cost at around 23 yen/kWH. The energy analysis of solar thermal power generation, based on the data given by the industrial correlation tables, indicates that the total energy required for construction of the system can be recovered in 2 to 3 years. Also outlined are construction of a 1MW pilot plant and its facilities, and designs of the pilot plants with a curved surface or tower type light collector. A total of 12 types of reflection mirrors are screened for establishing the air-exposure testing methods. Methods for treating back surface edges of the reflection mirrors are also investigated. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system (development of technology to manufacture thin film solar cells (surveys and researches on analyzing practical application )). Volume 1; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is intended to identify and analyze quickly and accurately the technological trends inside and outside the country on thin film solar cells, to reflect the results effectively on research and development of practical application of the thin film solar cells for power use, and to aid the research on practical application of the technology to manufacture the thin film solar cells. This fiscal year introduced the new project of researching and developing the poly-crystal silicon-based thin film solar cells. Discussions were given on designing the solar cells, including setting of thickness of an active layer required to improve efficiency of the silicon-based thin film solar cells, the light confining technology, and surface passivation. Comparisons and discussions were given on the new amorphous/poly-crystal silicon thin film manufacturing method and the conventional plasma CVD process. A research development program was introduced for a super laboratory to aid establishing the practical application technology for the silicon-based thin film solar cells. Chalcopyrite compounds including CuInSe2, and CdTe have not shown deterioration even in a long-term outdoor exposure test, hence they are noted as materials for high-efficiency solar cells and studied actively. Although still small in area, the net conversion efficiency was found in the order of 17%. Technological development has started to search mass production processes and commercialization possibility in the future. (NEDO)

Research on fabrication technology for thin film solar cells for practical use. Research on low-cost fabrication technology for large-area modules (Over-layered TCO on tempered glass for solar cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Daimenseki module no tei cost seizo gijutsu (kyoka class fukugo tomei doden kiban seizo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on the fabrication technology of over-layered TCO on tempered glass in fiscal 1994. (1) On the fabrication technology of heat-resistant over-layered TCO, thermal deformation of TCO substrates was studied by both experiment and numerical computation. The thermal deformation increased with carrier concentration. As the observation result on change in lattice strain of heated TCO films by high-temperature X-ray diffraction, lattice strain was largely affected by thermal expansion. (2) On development of the low-temperature heat treatment method of TCO films, a technological prospect was obtained for fabrication of low-resistance TCO films by heat treatment without strength deterioration of tempered TCO substrates. (3) On development of cost reduction technology, the large-area CVD equipment was devised on the basis of the inline tempering method which tempers substrate glass by air cooling after formation of SnO2 film as fabrication method of tempered TCO. The TCO substrate tempered by air cooling could endure the drop test of 227g and 1.5m. 5 figs., 1 tab.

Evaluation of environmental impact by LCA method. LCA shuho ni yoru kankyo fuka hyoka

Energy Technology Data Exchange (ETDEWEB)

Sakamura, H.; Utsuno, F.; Yasui, I. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)

1994-06-01

This paper explains the concept, history, and analytic methods of life cycle assessment (LCA), showing its application to beer bottles and cement factories as specific examples. The LCA is a method to calculate substances and energies put into the whole process of production of a product from raw material mining to product wasting and environmental loads emitted therefrom. It also evaluates the result collectively and quantitatively. A first case of the research is reportedly the one performed at Coca-Cola Co., Ltd. in 1969. Full-scale researches have gone forward in European countries in the recent several years, and are progressing to international networks. The analytic methods can be divided largely into an accumulation method to analyze data in each process and add them up, and a method to use an industrial association table. The former method is the most generally used method currently in overseas countries if referred to the LCA. Because the LCA can cause the analytic result and evaluation to vary depending on the purpose, it is important to define the goal, and set the scope. The LCA must develop in the future although it has a number of problems. 10 refs., 5 figs., 2 tabs.

Exergetic evaluation on photovoltaic/thermal hybrid panel; Taiyoko netsu hybrid panel no exergy hyoka

Energy Technology Data Exchange (ETDEWEB)

Iwaki, H; Morita, Y; Fujisawa, T; Tani, T [Science University of Tokyo, Tokyo (Japan)

1996-10-27

The photovoltaic/thermal hybrid panel (PV/T) is an energy converter that was designed for the composite use of electricity and heat. In this paper, the validity of PV/T designed for trial was evaluated based on an exergetic theory. As the result of an experiment, the electric exergetic value of PV/T and PV is each 65.8 kWh/m{sup 2} and 58.6 kWh/m{sup 2}. The former is higher than the latter by 11.2%. The total exergetic value of PV/T is also 1.2 and 8.2 times as high as those of a PV and solar collector (SC), respectively. The calculation result of the optimum temperature operation showed that the exergetic value of PV/T is 3.1 times as high as the electric exergetic value. Therefore, the operation must be performed with the electric and thermal exergetic values set in a ratio of 3.1 to 1. In this paper, the operating mode is handled in which importance was more attached to the electric exergy than the thermal exergy. The flow rate of a heating medium on PV/T is not thus the flow control that maximizes the PV/T exergy. In the future, studies including these points will be promoted. 7 refs., 7 figs., 3 tabs.

Leading research in FY 1995. Research of product evaluation and advanced measurements - Part 1 (product evaluation); 1995 nendo sendo kenkyu. Seihin hyoka kodo keisoku bunseki gijutsu ni kansuru chosa kenkyu - 1 (seihin hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Product evaluation has been investigated from a viewpoint of compatibility with human life by considering human being as the subject of life. This report describes the investigation results. Product evaluation is defined as evaluating products on a consumer-oriented viewpoint and informing consumers of the evaluation results. According to a questionnaire survey with regard to daily living products, products in the low degree of satisfaction in their usage were electric tooth brush, video camera, electric rice jar, vacuum cleaner, and electric iron. Contents of dissatisfaction with these products were classified by aspect, i.e., human aspect regarding human body/recognition, life aspect regarding functions of products and how to use them, and sensitivity aspect such as appearance of products. Thus, points at issue were clarified. As regards the human aspect, incompatibility between the size/form of products and human body/posture, and recognition psychological incompatibility such as difficulty in understanding function or operation of products were pointed out. Establishment of a method for measuring and evaluating the human`s body functions and the compatibility with products, and necessity of the acquisition of human`s body characteristic data and the consolidation positions are also described. 4 refs., 42 figs., 30 tabs.

Study on the best utilization of solar energy. Experimental study of hydrogen generation by water electrolysis using solar battery; Taiyo energy no yuko riyo ni kansuru kenkyu. Taiyo denchi riyosui denki bunkai suiso hassei field test

Energy Technology Data Exchange (ETDEWEB)

Kawashima, Y; Murai, K; Nakai, T [Himeji Institute of Technology, Hyogo (Japan)

1997-11-25

Shortcomings of solar energy are that it is subject to weather and is not available in the nighttime. The weak points may be effectively made up for when solar energy collected on a fine day is stored in the form of hydrogen energy for recovery as required. In this report, power generated by solar cells is used for the electrolysis of water for the generation of hydrogen. The amounts of the thus-generated hydrogen and hydrogen energy are determined and, on the basis of the measured amount of insolation, the solar energy availability rate (hydrogen conversion performance) is calculated. The amount of hydrogen generated in fiscal 1996 is also calculated for every month. The hydrogen generation level is quite low in the TiO2 wet type solar cell, approximately 0.2% at most. The current efficiency is fairly high in hydrogen generation using electrolysis, which is approximately 96-97%. The efficiency is higher when several units of electrolyte are connected in series until the solar cell optimum voltage is attained. A linear relationship is found between the daily summation of insolation and the amount of hydrogen generated. 1 ref., 7 figs., 2 tabs.

To the partnership in Kanegafuchi Chemical Industry and solar cell; Kaneka, taiyo denchi de teikei he

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Kanegafuchi Chemical Ind. clarified that the consultation was advanced in the direction in which the business cooperates with BP Amoco Corp. in international oil majors on the solar cell business on 11 th capital. In full amount fund subsidiary of the bell pool chemistry, the solar cell making and selling company is established in the joint venture in Europe and America, Asia, when the BP Amoco Corp. does capital participation in money mosquito solar tech which is the production marketer of solar cell. The plan which develops the amorphous solar cell of low cost which the bell pool chemistry developed in the world. The consultation of the partnership is also arranging prospect in the end June, and it seems to greatly jump by uniting with the BP Amoco Corp. of the largest hand. (translated by NEDO)

CO2 recovery system using solar energy; Taiyo energy wo riyoshita CO2 bunri kaishu system

Energy Technology Data Exchange (ETDEWEB)

Hosho, F; Naito, H; Yugami, H; Arashi, H [Tohoku University, Sendai (Japan)

1997-11-25

As a part of studies on chemical absorption process with MEA (monoethanolamine) for CO2 recovery from boiler waste gas in thermal power plants, use of solar heat as MEA regenerating energy was studied. An integrated stationary evacuated concentrator (ISEC) effective as collector in a medium temperature range was used to realize a regenerating temperature range of 100-120degC. ISEC is featured by vacuum insulation, use of selective absorbing membranes for an absorber, a CPC (compound parabolic concentrator)-shaped reflection mirror, and high-efficiency. An MEA regenerator is composed of an ISEC and PG(propylene glycol)-MEA heat exchanger, and circulates PG as heat medium. Heat collection experiment was also made using water instead of MEA. Both batch and continuous systems could supply a heat quantity necessary for MEA regeneration. CO2 concentration in the top of the regenerator rapidly decreased with PG circulation regenerating MEA. As mol ratios of CO2/MEA were compared between before and after regeneration, a recovery rate was estimated to be 59.4% for the batch system. 8 figs., 4 tabs.

Stabilized efficiency of stacked a-Si solar cell; Sekisogata a-Si taiyo denchi no anteika koritsu

Energy Technology Data Exchange (ETDEWEB)

Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

1997-11-25

Different types of tests combining light and temperature were carried out in a laboratory on predicting long-term performance of stacked amorphous silicon solar cells. Cell terminals were left open, xenon was used as an irradiation light source, and cell temperature was controlled within {+-} 2 degC of the setting. The result of the experiment may be summarized as follows: with regard to the deterioration characteristics, the speed in which the efficiency changes reached a maximum within 10 hours, and thereafter the change has slowed down gradually in the case of temperature at 50 degC; in the case of 25 degC, the maximization is reached between 500 and 1000 hours; the stabilization efficiency turns out to be a pessimistic value according to the saturated value derived from an experimental expression, hence the value would have to be expressed by specifying cell temperatures, light intensities and elapsed time; the minimum value of seasonal variation may be estimated at about 85% as a pessimistic value; for recovery characteristics, the saturated value for the recovery tends to become lower as the lower the value immediately before the recovery; and if the light intensity is varied, the deterioration characteristic shifts to that at an individual light intensity. 4 refs., 11 figs., 2 tabs.

PV glass curtain walls; Kenzai ittaigata taiyo denchi gaiheki no kaihatsu (glass curtain wall eno tekiyo)

Energy Technology Data Exchange (ETDEWEB)

Yoshida, T.; Iwai, T.; Ouchi, T.; Ito, T.; Nagai, T.; Shu, I. [Kajima Corp., Tokyo (Japan); Arai, T. [Showa Shell Sekiyu K.K., Tokyo (Japan); Ishikawa, N.; Tazawa, K.

1997-12-20

Reported in this article are PV (photovoltaic) modules now under development for integration into building walls. First of all, the power generating capability of PV modules and appropriate use of the generated power are studied, and the performance (resistance to fire or incombustibility, strength and durability, appearance and design, and dimensional standardization) that such outer wall materials are to be equipped with are determined. Next, module development, installation technique, computer graphics-aided facade designing, and real size module-using proof test are studied before installability, the power to be generated, and designs are finalized. In the development of modules, design evaluation involves the combining of various kinds of glass, solar cells, back sheets, and fillers, and the importance is confirmed of the prevention of insulation degradation around the modules. As for the methods of installation, the gasket method and aluminum sash method, etc., are tested. In the study of facade design, it is found that various expressions are possible by properly choosing gasket colors, module types, and kinds of glass to cover the openings. 1 ref., 6 figs., 3 tabs.

Effect of water pollution on marine organisms; Sekiyu osen no kaiyo seibutsu eno eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Ogata, M. [Okayama Univ., Okayama (Japan); Fujisawa, K. [Okayama Prefectural Fisheries Experiment Station, Okayama (Japan)

1997-10-10

Toxicity of petroleum component to aquatic organisms appears as a result of its deposition onto living organisms followed by its migration into bodies of the organisms, and emergence of toxicity from the migrated component. Effect evaluation processes standing on this viewpoint may include the exposure monitoring or migration monitoring, in which the petroleum component migrated into marine organisms is analyzed and the state of the component concentrated in these organisms is measured, or effect monitoring, in which actions of the petroleum component in the organisms are investigated. The effects of petroleum on aquatic organisms would include the following occurrence: direct fatal toxicity acting on cells and membranes, quasi-fatal toxicity causing death indirectly through feeding actions and abnormal actions, direct coating of oil on surface of organisms, which prevents movability and feeding actions of the organisms and reduces hydrophilicity of plumes and hairs, pollution of living organisms due to migration of carcinogenic aromatic compounds into bodies of the living organisms, and change in species compositions and geographic distribution of living organisms due to change in physico-chemical environment. This paper explains cases of detection and identification of organic sulfur compounds, aromatic compounds, polycyclic aromatic compounds, paraffins, olefins and heavy metals in parametric compounds of petroleum. 20 refs., 4 figs., 3 tabs.

Environmental impact assessment caused by global warming. Chikyu ondanka no eikyoryo hyoka to sono taisaku

Energy Technology Data Exchange (ETDEWEB)

Oshima, K [Geological Survey of Japan, Tokyo (Japan)

1991-09-01

This paper describes the considerations on the influence of the global warming on the environment, and the discussions on the measures against the climatic changes. With respect to the environmental effects by the global warming, the considerations were given based on the studies on the effects of mainly the Quaternary climatic changes on the surface sea water temperatures, sea level and animal flocks. If the magnitude of the climatic changes anticipated to occur during the 21st century is lower than that have taken place in the past 10,000 years during which the agricultural production has developed to a full-scale, there would be no fear of drastically changing the ecology on earth. If the estimation of future climatic and environmental changes becomes possible, then four basic positions could be selected for establishing the contermeasure plans. That is, the first is the measures to correspond to birth-rebirth transmigration; the second is the measures to carbon dioxide disposition upon concluding that the cause for the global warming is the atmospheric increase of carbon dioxide concentration, measures for conservation and international cooperation; the third is to deal with the warming environments; and the fourth is the means to reconstruct the earth. While a number of countermeasures may be prepared, Which of them should be selected will be decided by the amount of effects. 15 refs., 6 figs., 1 tab.

Local approach to brittle fracture under residual stress field. Assessment of pre-loading effect; Local approach no tekiyo ni yoru zanryu oryoku wo motsu buzai no zeisei hakai kyodo hyoka. Yokaju no eikyo no hyoka

Energy Technology Data Exchange (ETDEWEB)

Yamashita, Y.; Sakano, K.; Onozuka, M. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Minami, F. [Osaka University, Osaka (Japan)

2000-01-01

The effect of residual stresses on brittle fracture was investigated on the basis of the Local Approach. Compressive residual stress was introduced by pre-loading and the subsequent fracture test conducted with a 780 MPa class steel. Preloading apparently increased the critical load and critical CTOD at the onset of brittle fracture initiation. The Weibull stress criterion was used to evaluate the brittle fracture resistance of the pre-loaded specimen. The critical Weibull stress is a material property independent of test conditions with and without pre-loading. Using the Weibull stress criterion, the critical CTOD of the pre-loaded specimen can be predicted from test results of the specimen without pre-loading. (author)

Fiscal 1974 Sunshine Project result report. R and D on solar energy system (weather survey). Part 1. Bibliography on solar radiation; 1974 nendo taiyo hosha ni kansuru bunken mokuroku. 1. Taiyo energy system no kenkyu kaihatsu (kisho chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

This report is the 1st one among 3 reports 'Bibliography on solar radiation', 'Guideline for using weather data' and 'Observation data on global solar radiation and sunshine duration'. This report is composed of the part 1 'Present state and view of researches on solar radiation' including (1) view of researches on short-wave radiation, (2) atmospheric radiation, (3) scattering of solar radiation, (4) global net radiation and (5) radiometer, and the part 2 including the bibliography and its commentary. (1) describes researches on incident short-wave radiation (solar radiation) and some current issues, (2) describes the basis for quantitative measurement of atmospheric radiation transfer, based on the premise that atmospheric radiation is infrared radiation between the ground surface and atmospheric system. (3) describes scattering of solar radiation in the air, and its effect. (4) describes that the global profile of net radiation of the air-earth system and its seasonal change can be observed directly from the weather satellite roughly, and research on global net radiation is approaching a new era. (NEDO)

30th Solar Energy Promotion Committee Meeting - 5th Solar Cell Liaison Meeting. Combined report for fiscal 1989-1992; Dai 30 kai taiyo energy suishin iinkai dai 5 kai taiyo denchi renrakukai (1989-1992 nendo hokoku no matome)

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-04-20

The above-named events were convened in Tokyo in the period of April 20-23, 1993, where a total of 51 presentations were given on research achievements. Presented in the session on a-Si systems were 22 essays concerning high quality manufacturing technology - high integration technology, large area manufacturing technology - large area a-Si tandem solar cell, highly reliable manufacturing technology - bilayer device, composite transparent conductive film - transparent conductive film with performance enhanced by compositing, etc. Presented in the session on chalcopyrite and II-VI group systems were 8 essays concerning amorphous/compound tandem cell manufacturing technology, research on compound semiconductor solar cell, etc. Presented in the session of III-V group systems were 6 essays concerning research on compound semiconductor solar cell - superlattice structure tandem cell, development of InGaP/Si tandem solar cell, etc. In the session of crystalline Si systems, 15 essays were presented concerning highly pure silicon manufacturing technology, highly pure substrate manufacturing technology, etc. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on solar energy system (weather survey). Part 1. Bibliography on solar radiation; 1974 nendo taiyo hosha ni kansuru bunken mokuroku. 1. Taiyo energy system no kenkyu kaihatsu (kisho chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

This report is the 1st one among 3 reports 'Bibliography on solar radiation', 'Guideline for using weather data' and 'Observation data on global solar radiation and sunshine duration'. This report is composed of the part 1 'Present state and view of researches on solar radiation' including (1) view of researches on short-wave radiation, (2) atmospheric radiation, (3) scattering of solar radiation, (4) global net radiation and (5) radiometer, and the part 2 including the bibliography and its commentary. (1) describes researches on incident short-wave radiation (solar radiation) and some current issues, (2) describes the basis for quantitative measurement of atmospheric radiation transfer, based on the premise that atmospheric radiation is infrared radiation between the ground surface and atmospheric system. (3) describes scattering of solar radiation in the air, and its effect. (4) describes that the global profile of net radiation of the air-earth system and its seasonal change can be observed directly from the weather satellite roughly, and research on global net radiation is approaching a new era. (NEDO)

Research and development of evaluation system for photovoltaic power generation system. Research and development on evaluation technology of photovoltaic power generating systems; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. System hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of evaluation technology for photovoltaic power generating systems in fiscal 1994. (1) On preparation of test facility and measuring instrument, the pyrheliometer with a photovoltaic device as sensor was developed. (2) On collection and analysis of data, operation data of interconnection system, stand alone system, and water pump system were collected, and energy flow was analyzed. The following were also analyzed: time variation of a-Si solar cell modules, fluctuation correction factor of spectrum response, that of nonlinear response of crystalline solar cells, effect of solar radiation intensity and wind velocity on temperature rise of modules, and correction factor of DC circuit losses. (3) On on-site measurement technology, the array output measuring instrument was developed on the basis of capacitor charge system. (4) On simulation technology, simulation analyses of energy flow, optimum capacity of interconnection systems, correction factor of solar radiation, and capacity of array storage batteries were conducted. 3 figs., 6 tabs.

Confinement of solar thermal energy by Nesa film; Nesa maku ni yoru taiyo netsu energy no fujikome

Energy Technology Data Exchange (ETDEWEB)

Shimizu, A; Yano, K; Kasuga, M; Daigo, Y [Yamanashi University, Yamanashi (Japan). Faculty of Engineering

1997-11-25

This paper reports a Nesa (SnO2) film as selective transmissive film for effective confinement of solar thermal energy. Solar light spectrum ranges from 0.3 to 2.0{mu}m, while thermal radiation from bodies at 100-200degC is infrared ray more than 2{mu}m. Consequently, a solar water heater using the film which can pass rays below 2.0{mu}m while reflect rays over 2.0{mu}m for windows is very efficient. The Nesa film reflects rays with wavelengths more than plasma wavelengths (controllable from 1 to several {mu}m) by plasma action of free electrons. The Nesa films with different carrier densities were fabricated by spraying deposition method at dopant rates (Sb/Sn) from 0 to 2mol%. The solar water heaters were prepared using normal glass and specific glass coated with the Nesa film as selective transmissive film. The heater using the glass coated with the Nesa film of 2{mu}m plasma wavelength for windows could efficiently confine solar heat. The Nesa film of 700nm plasma wavelength which can pass visible light while reflect infrared ray was effective to reduce cooling/heating losses. 3 refs., 6 figs.

Forced-circulation solar water heater using a solar battery; Taiyo denchi wo mochiita kyosei junkahshiki taiyonetsu onsuiki

Energy Technology Data Exchange (ETDEWEB)

Asai, S; Mizuno, T [Yazaki Corp., Tokyo (Japan)

1997-11-25

Optimal operation control was discussed on a forced-circulation solar water heater using solar cells not only as the power supply of a heat collecting pump, but also for controlling operation of the heat collecting pump. With this system, when the amount of power generated by solar cells reaches a sufficient level for operating the heat collecting pump, the heat collecting pump starts operation, wherein the heat collecting medium circulates in the system. The discussion was given by using simulation based on experimental expressions such as the relation expression between insolation and heat collecting medium flow rate as derived from the result of the system`s heat collecting performance test. As a result, the following conclusions were obtained: optimal insolation for activating the discussed system is from 50 to 100 W/m {sup 2}, and the heat collected within this range is within -1.5% of the collected heat amount at an optimum value; optimal activating insolation for the case of 1000 to 2000 W/m {sup 2} with low daily cumulative insolation is from 0 to 50 W/m {sup 2}, whereas the optimal activating insolation amount increases as the daily cumulative insolation amount increases; and the optimal activating insolation amount increases as water to be supplied requires higher temperature. 1 ref., 17 figs., 2 tabs.

Forced-circulation solar water heater using a solar battery; Taiyo denchi wo mochiita kyosei junkanshiki taiyonetsu onsuiki

Energy Technology Data Exchange (ETDEWEB)

Asai, S; Mizuno, T [Yazaki Resources Co. Ltd., Shizuoka (Japan)

1996-10-27

For the purpose of satisfying demands for qualitative improvement on tapwater temperature and pressure, an indirect-type solar water heater using solar cells, in which a closed type hot water storage tank connected directly to the water supply is integrated with a solar collector, was examined for its characteristics and performance. The heat collecting medium is a water solution of polypropylene glycol, which circulates through the solar collector pump, cistern, solar collector, and heat exchanger (hot water storage tank). The results of the test are summarized below. When comparison is made between the two solar collector pump control methods, the solar cells direct connection method and the differential thermo method utilizing temperature difference between the solar collector and the hot water storage tank, they are alike in collecting heat on clear days, but on cloudy days the latter collects 5% more than the former. In winter, when the heat exchanger heat transfer area is 0.4m{sup 2} large, a further increase in the area improves but a little the heat collecting efficiency. An increase in the medium flow rate and temperature, or in the Reynolds number, enhances the heat collecting efficiency. 13 figs., 6 tabs.

Solar cell array for driving MOS type FET gate. MOS gata EFT gate kudoyo taiyo denchi array

Energy Technology Data Exchange (ETDEWEB)

Murakami, S; Yoshida, K; Yoshiki, T; Yamaguchi, Y; Nakayama, T; Owada, Y

1990-03-12

There has been a semiconductor relay utilizing MOS type FET (field effect transistor). Concerning the solar cells used for a semiconductor relay, it is required to separate the cells by forming insulating oxide films first and to form semiconductor layers by using many mask patterns, since a crystal semiconductor is used. Thereby its manufacturing process becomes complicated and laminification as well as thin film formation are difficult, In view of the above, this invention proposes a solar cell array for driving a MOS type FET gate consisting of amorphous silicon semiconductor cells, which are used for a semiconductor relay with solar cells generating electromotive power by the light of a light emitting diode and a MOS type FET that the power output of the above solar cells is supplied to its gate, and which are connected in series with many steps. 9 figs.

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system /development of technology to manufacture solar cells/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture silicon crystal based high-quality materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi seizo gijutsu kaihatsu, usumaku taiyo denchi seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (silicon kesshokei kohinshitsu zairyo kiban no seizo gujutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is intended to develop thin film solar cells capable of mass production with high photo-stability and at low cost. Thus, the objective of the present research is to analyze the growth process of micro crystal silicon based thin films, the crystal being a high quality silicon crystal based material, and develop technology to manufacture high-quality micro crystal silicon thin films based on the findings therefrom. It was found that, when silicon source is available in cathode, pure hydrogen plasma forms micro crystal silicon films by using the plasma as a result of the chemical transportation effect from the silicon source. It was revealed that the crystal formation due to hydrogen plasma exposure is performed substantially by the crystals forming the films due to the chemical transportation effect, rather than crystallization in the vicinity of the surface. The crystal formation under this experiment was concluded that the formation takes place during film growth accompanied by diffusion of film forming precursors on the surface on which the film grows. According to the result obtained so far, the most important issue in the future is particularly the control of crystal growing azimuth by reducing the initially formed amorphous layer by controlling the stress in the initial phase for film formation, and by controlling the film forming precursors. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and dessolution deposition process); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu (yokai sekishutsuho))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to manufacture low-cost large-area solar cell modules, developmental research has been performed on a film manufacturing technology using the dessolution deposition process. This paper summarizes the achievements in fiscal 1999. The research has been performed on a technology to form a thin silicon film directly on carbon substrates being substrates of different kinds, without using seed crystals. The researches made up to the previous fiscal year has made possible to form the film onto a substrate of about 5-cm square, has fabricated cells although with a small area, and indicated the importance of reducing concentrations of impurities in the solvent metals used. The researches performed during the current fiscal year executed modifications to reduce the temperature distribution in the substrate surfaces, including size increase in the heater, and improvement in the cooling heat conduction mechanism. As a result, films were formed successfully on 7.5-cm square substrates. In reducing the process temperatures, it was made clear that films can be formed at lower than 700 degrees C by using zinc as a solvent metal. Furthermore, the purity enhancement in the solvent metal achieved a conversion efficiency of 11.6% although the area is as small as 3.73 cm{sup 2}. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Dissolution/deposition method); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (yokai sekishutsuho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to manufacture the above at low cost by a dissolution/deposition method. Under this method, a film is fabricated containing crystals high in quality and large in size though the film area is very small. In fiscal 1998, an effort to fabricate a film to cover a 10cm square substrate failed. The failure is explained by that the heater was too small for the substrate area and that the failure to uniformly heat the substrate resulted in an inplane temperature distribution greater than expected. The furnace was modified in a minor way to narrow substrate temperature distribution as much as possible. Another attempt was made to fabricate a larger-area film on a 5cm square substrate, and then crystals grew to cover approximately the whole surface of the 5cm square substrate. Efforts will continue to achieve the goal. As for the mechanism of film fabrication on substrates of different kinds, self-coating is now described by difference in heat conductivity between a carbon substrate and silicon substrate. Thanks to individual control in a small film fabricating unit, a film thickness of approximately 100 micrometers was achieved. The distance of diffusion was 30 micrometers or more in the case of a small area, and the efficiency of a solar cell using this film was found at 10.2%. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules (dissolution and deposition process); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (yokai sekishutsuho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was performed by noticing on the plasma spraying method as a process that can manufacture thin poly-crystalline silicon films at a high speed. Fiscal 1997 has established a technology that can form a silicon film directly without using seed crystals in an area of 2-cm square on a carbon supported substrate by using a small film manufacturing equipment using the dissolution and deposition process. The size of the crystal is as very large as several hundred {mu}m, by which a possibility of making high-performance solar cells was verified. Discussions were given to apply this technology to large-area substrates, whereas a device was developed, which is capable of forming a film in an area corresponding to 10-cm square. According to a film forming experiment using this device, the film has begun being formed on part of a 10-cm square substrate, verifying the effectiveness of this method. While the film thickness is about 100 {mu}m, it was confirmed that the crystal size will not change even if the thickness is made mechanically as thin as about 50 {mu}m. Further discussions were given on enhancement of wettability by means of coating, and light enclosing structure. (NEDO)

Performance evaluation of a flow-down collecting solar system; Ryuka shunetsushiki solar system no seino hyoka

Energy Technology Data Exchange (ETDEWEB)

Kanayama, K; Li, X; Baba, H; Endo, N [Kitami Institute of Technology, (Japan)

1997-11-25

The paper evaluated performance of a flow-down collecting solar system. The solar heat pump PV system is composed of a solar system, heat pump and PV, of which the heat collecting portion is a water-use horizontal evacuated double glass tube solar collector. As a result of the performance measurement, the necessity of fundamental improvement arose. Under an idea of disproving common sense of the original forced circulation solar system, a system was designed in which heat is collected by making the heat media reversely circulate and flow down in accordance with gravity. When the flow rate was 2m{sup 3}/h, the collecting rate reached a maximum, approximately 54% (36.9% before improvement). When the flow rate was 1.3-1.5m{sup 3}/h, the system can realize the maximum merit, and the collecting efficiency became approximately 50%. Helped by reduction in consumed power, the average system performance coefficient reached more than 85% (28.9% before improvement). The obtainable energy rate rapidly increased to 2.9 times more than before improvement. Further, the consumed power of pump was decreased 65% from before improvement when the flow rate was 2.4m{sup 3}/h. 2 refs., 5 figs.

Evaluation for membrane components of water recycling system. Mizu saisei junkan system yoso no tokusei hyoka

Energy Technology Data Exchange (ETDEWEB)

Tanemura, T; Otsubo, K; Oguchi, M [National Aerospace Laboratory, Tokyo (Japan); Ashida, A; Hamano, N; Mitani, K [Hitachi, Ltd., Tokyo (Japan)

1992-04-01

The configuration of water recycling systems with membrane filters was studied to purify waste water discharged from human beings, animals and plants which is a key subsystem for closed ecological life support systems (CELSS) essential to long-term manned space activity. The filter performance test apparatus with three kinds of filters such as pre-filter, reverse osmosis membrane filter and ultra membrane filter was fabricated to conduct long-term cycling high-concentration tests using artificial urine as original waste water. As a result, since every membrane filter offered their nominal performance incompletely in high-concentration tests, it was necessary to add an NaCl removing apparatus to the system as primary treated water should be used for vegetation. It was also required to test the membrane performance preliminarily because the performance such as membrane life was different between various waste waters. 7 refs., 32 figs., 9 tabs.

Psychoacoustic parameters and its measuring system; Onshitsu hyoka wo hyokasuru tame no parameter to keisoku system

Energy Technology Data Exchange (ETDEWEB)

Ohashi, M.; Imaizumi, H.; Ono, T. [Ono Sokki Co. Ltd., Tokyo (Japan)

1998-05-01

Human auditory sensation has both extremely excellent performance and general versatility as sound analyzer. At present, it is impossible to make equipment with the same functions as human being, and describe an auditory sensation function as acoustic sensor even by any physical analysis techniques. However, extraction of auditory sensation parameters is becoming possible by using psychoacoustics and binaural signal processing. This paper mainly explains the calculation method of sound quality evaluation parameters derived from psychoacoustic results based on a sound quality evaluation system under development by the authors. This system is based on binaural measurement by dummy head, and calculates psychoacoustic parameters such as loudness, sharpness, roughness, fluctuation strength and tonality through frequency analysis of the measured stereo signals. The system also calculates 2-D parameters such as sensory pleasantness and unbiased annoyance based on the above parameters. 12 refs., 4 figs.

Test and evaluation on safety relating to biotechnology; Biotechnology ni kansuru anzensei no shiken to hyoka

Energy Technology Data Exchange (ETDEWEB)

Okada, M. [Bio-Oriented Technology Research Advancement Inst., Saitama (Japan)

1996-09-05

This paper describes the current status and how works are being carried out on safety tests and evaluation of gene recombinants in plants and microorganisms. In the field of plants, Flavr Savr tomato which has been improved in fully ripe fruit distribution and keeping quality was commercialized as the world`s first recombinant food in May 1994 by Calgene, Inc. of America. Other vegetables, such as soybean, corn, potato, and pumpkin have been completed of all items of safety evaluation, and are approaching the commercialization phase. The safety evaluation system for living organisms created by using recombinant DNA technologies has been established internationally with regard to its general framework and contents based on accumulated knowledeges and experiences as a result of utilization of over twenty years. Industrial utilization guidelines for recombinants in Japan have been established in correspondence with the OECD recommendation in 1986. Experiments to verify recombinants to be safe in environment, and cultivation of the recombinants for utilization are performed based on the experimental guidelines and utilization guidelines. 15 refs., 1 fig., 5 tabs.

Assessment report on the development of functionally inclined material; Keisha kinosei zairyo no kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Concerning a project whose aim is to develop heat resistant engine members through the application of the concept of functionally inclined materials, deliberation and assessment are made of the meaning of its implementation, validity of the research program, research achievement, etc. The project deals with a specimen, diameter 150mm or more and thickness 5mm or more, built of a zirconia/stainless steel-based functionally inclined material, and its goal is to develop technologies for optimizing the baking process for the said specimen, baking system and related devices, assessment technique, tribological assessment technique, etc., and it is inferred that these targets are reasonable. As the result of this research, an energy-efficient (power consumption reduced to 1/3 to 1/5) practical rapid sintering system is constructed. Basic data are collected relative to the tribology of the functionally inclined material, and it is proved that it is feasible to use the material for engine members. The process technology, assessment technology, and devices developed under this project are the first in the world, and are highly evaluated. (NEDO)

Study of test procedure to evaluate airbag deployment force; Airbag tenkairyoku no hyoka shuho no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kamiji, K.; Fukuda, K.; Morita, K. [Honda Motor Co. Ltd., Tokyo (Japan)

1998-05-01

Discussions were given on airbags equipped in passenger cars as to methods of evaluating their deployment injuries. Airbag deployment injuries occur in occupants being out of position. In a driver`s seat, an injury may occur when an air bag deploys under a condition that a driver with relatively short body height gets closer to a steering wheel to maintain the driving posture. In a front passenger seat, if a child is not held in a restraint equipment, the child may be blown off into the vicinity of the airbag, whose deployment can cause an injury. According to the result of a test performed on a driver being out of position, the test method using a hybrid 3 dummy specified in the present ISO procedure may not necessarily be said to produce an evaluation on the worst case. In order to solve the problem, an ATD dummy which can measure bend in each rib independently would be used, or the hybrid 3 dummy must be measured in the worst set position. 4 refs., 8 figs.

Study on solar collector utilizing electro-hydrodynamical effect; Denki ryutai rikigaku koka wo riyosuru taiyo shunetsuki no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sato, M; Aoki, H; Wako, Y [Hachinohe Institute of Technology, Aomori (Japan)

1997-11-25

This paper proposes a cone type electro-hydrodynamical (EHD) heat collector, describes its structure and principle, and mentions possibility of improving the heat collecting efficiency. The paper proposes a heat collector with a shape close to a cone. Trees are of cone form so that their every leaf, branch and truck can capture solar energy efficiently. Imitating this fact existing in the natural world, a cone-shaped heat collector was fabricated on a trial basis to discuss its heat collecting efficiency. Furthermore, black round stones are placed in the inner cone of the cone- shaped heat collector of double-glass structure. A low boiling point medium is placed between the inner and outer cones to cause corona discharge in vapor generated by absorbing the solar heat, and generate corona wind for an attempt to accelerate heat transfer into a heat exchanger. Thus, development was made on a cone-shaped high-efficiency heat collector utilizing electro-hydrodynamical (EHD) effect, and elucidation was given on dynamic phenomena of an electro-thermal fluid. Heat transfer in the EHD heat collector has a possibility of being accelerated by generation of ionic wind. In addition, it is thought that there would be an optimum value in applied voltage to increase electric charge supply as a result of corona discharge. 1 ref., 2 figs.

Estimation of the charge quantity from solar cell to battery; Taiyo denchi ni yoru chikudenchi eno juden yosoku

Energy Technology Data Exchange (ETDEWEB)

Tsutsumi, K; Nishitani, M [Daiichi University, College of Technology, Kagoshima (Japan)

1996-10-27

In performing an experiment of running a small electric vehicle by installing solar cells in it and by charging the storage battery at a specific voltage, an estimation was made on the charge quantity to the battery for each solar altitude and inclination of a module at different hours. The solar altitude was determined at Daiichi University, College of Technology, according to the month and the time of day from a formula using day-declination and time equation of a chronological table of science. The quantity of global solar radiation was determined by resolving the solar radiation into its direct and diffuse components on the basis of the extra-terrestrial solar radiation quantity with the change in radius vector taken into consideration; and then, the global solar radiation on the inclined face was obtained from the angle of inclination and incidence. On the roof of a Daiichi University building, solar cell modules were installed facing north and south at 0{degree}, 30{degree}, 45{degree}, 60{degree} and 90{degree} each, so that a short-circuit current was measured for each differently inclined angle. As a result of the experiment, shown in an regression formula is a relation between the temperature conversion value of the maximum output of the solar cell at the standard temperature of 25{degree}C and the quantity of solar radiation on the inclined surface. Consequently, it enabled the prediction of a charging quantity, in the case of running a small vehicle with solar cells installed, from the quantity of solar radiation on the inclined surface in the clear weather. 2 refs., 4 figs., 2 tabs.

Research and development of evaluation system for photovoltaic power generation system. Research and survey on test and evaluation method for BOS component devices; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Shuhen gijutsu hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of the evaluation method for BOS component devices in fiscal 1994. (1) On the study on requirements of BOS component devices for practical use, the study results on storage battery, inverter, protective device for system interconnection, and effective use means for storage battery were summarized. On the future device technology, it was clarified that the following value added technologies are promising: simple design of inverter circuit, cost reduction by common specification and mass production, and stabilization of voltage and compensation of momentary peak load by combining inverter with small-capacity storage batteries. (2) On the study on the performance test method for BOS component devices, basic characteristic (capacity, efficiency) test, PSOC charge/discharge cycle test, and accelerated life cycle test were performed for 4 kinds of new storage batteries developed by NEDO. The whole characteristic test results satisfied specifications, and long-term cycle test is in promotion for all new storage batteries. 3 figs., 4 tabs.

Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-10-01

Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

Treatability evaluation of membrane technique by virus. Maku shori ni okeru shorisei hyoka to shite no virus

Energy Technology Data Exchange (ETDEWEB)

Yano, K. (Tokyo Metropolitan Research Lab. of Public Health, Tokyo (Japan))

1990-08-10

Concerning a high level treating method of regeneration of sewage water, there are methods of coagulation/precipitation, sand filtering and ozone treatment in addition to the conventional active sludge method. However, none of these methods are perfect from the viewpoint of virus. A film treating method to remove micro-organisms in water is twofold, i.e., microfiltration and reverse osmosis. For such filter treatments, polio virus is most suited as an experimental index for conducting an assessment of the treating ability of viruses. The reasons are as follows: 1. It is the smallest virus among the viruses which are mixed in the water systems. 2. Polio virus is always detected in the study of actual conditions of the viruses contained in the sewage waters. 3. It involves less danger in handling because there are vaccines which are made less poisonous. 4. Separation and quantification of viruses is easily conducted by means of cultured cells. 8 refs., 1 fig., 7 tabs.

Evaluation of economical efficiency of the Osaki large hydroponic facilities; Osaki ogata suiko shisetsu no keizaisei hyoka

Energy Technology Data Exchange (ETDEWEB)

Yonezawa, K [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

1996-03-25

A demonstrative test was conducted to verify economical efficiency of practical scale hydroponic horticulture under structure making use of a part of the Osaki thermal power plant to be constructed. In the test, the hydroponic culture of leek and tomatoes was carried out for six years starting 1989 to study its economical efficiency. Using the M-type hydroponic culture facilities, the structures are 1200m wide, 29m long, and 21 tons in the culture liquid level in case of leek, and 350m wide, 29m long, and 10 tons in the culture liquid level in case of tomatoes. The evaluation was made estimating the crop amount of leek as about 35 tons and that of tomatoes as about 60 tons and regarding that the sales amount is equal to the crop amount. The sales amount of leek is 28 million yen, and when seeking income/expenditure from expenses, deficit of 1 million yen per 30 a cannot be avoided excluding the equipment depreciation cost. As to tomatoes, the shipment cost is approximately 14 million yen without the equipment depreciation cost, but the sales amount is approximately 13-19 million yen largely affected by the unit price. A study on the sale method is needed. 7 figs., 11 tabs.

On the method for fracture strength assessment. Part 2; Kozobutsu no hakai kyodo hyoka no jissai. 2

Energy Technology Data Exchange (ETDEWEB)

Onozuka, M. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1995-09-05

In order to reduce the economic cost of the generating set etc. the damages to the materials and structures of the structure to last the original design life were observed and it was considered that if damages were fewer the life would be longer. One of the important items in assessing, amending and renewing the rationality of the established structure is the assessment of the defects and flaws existing in the welded joints. In Japan, WES 2805 which is named as the Method for Assessing the Defects for the Brittle Fracture Occurring Properties of Welded Joint was formulated in 1980 as the standard of the Japan Welding Society. Although it has been applied as the criterion in wide range, the part on brittle fracture is now under revision to reflect the research results on fracture mechanics thereafter and to perfect the fracture relationship because many years have passed since its first formulation. In this paper, the contents in the final stage of the revision of WES 2805 standard, including concrete examples, were introduced. 2 refs., 6 figs., 2 tabs.

Feasibility study for seismic monitoring of gas injection; Atsunyu gasu monitaringu no kanosei hyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nishida, A.; Ogawa, T.; Yokota, T.; Shimada, N.; Onozuka, S.; Kono, F.; Miyagi, T. [Japan National Oil Corp., Tokyo (Japan)

1998-10-30

In this study, seismic monitoring of injected gas in a carbonate reservoir was investigated using multidisciplinary approach which consisted of geological/reservoir modeling, reservoir flow simulation, rock physics and seismic modeling. A case study was conducted over Lower Cretaceous carbonate reservoir offshore Abu Dhabi. The gas saturation and reservoir pressure data were obtained from the reservoir flow simulation. The velocity data of dry rock samples under the various conditions were also obtained from rock physics study. These outputs were converted to the velocity model using Gassmann's equation. The calculated velocity from Gassmann's equation is well correlated with velocity from laboratory measurements. Therefore we con confirm that the Gassmann's equation is applicable to estimate the velocity of the gas saturated reservoir rock. Based on the velocity model, synthetic seismic sections before and after gas injection were constructed in order to verify the influence of gas flood. As the results, amplitude difference between the two synthetic seismograms was observed at top and bottom reflectors of the reservoir zone. This amplitude variation is caused by both gas saturation change and pressure change. Although further investigation is needed to detect the cause of the variation, this study indicates the possibility of seismic reservoir monitoring. (author)

Geological evaluation on productibility of coal seam gas; Coal seam gas no chishitsugakuteki shigen hyoka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Fujii, K [University of Shizuoka, Shizuoka (Japan). Faculty of Education

1996-09-01

Coal seam gas is also called coal bed methane gas, indicating the gas existing in coal beds. The gas is distinguished from the oil field based gas, and also called non-conventional type gas. Its confirmed reserve is estimated to be 24 trillion m {sup 3}, with the trend of its development seen worldwide as utilization of unused resource. For the necessity of cultivating relevant technologies in Japan, this paper considers processes of production, movement, stockpiling, and accumulation of the gas. Its productibility is controlled by thickness of a coal bed, degree of coalification, gas content, permeability, groundwater flow, and deposition structure. Gas generation potential is evaluated by existing conditions of coal and degree of coalification, and methane production by biological origin and thermal origin. Economically viable methane gas is mainly of the latter origin. Evaluating gas reserve potential requires identification of the whole mechanism of adsorption, accumulation and movement of methane gas. The gas is expected of effect on environmental aspects in addition to availability as utilization of unused energy. 5 figs.

Study of evaluation for grouting effect in a borehole; Yakueki chunyu koka hyoka gijutsu ni okeru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, H; Matsuo, T [Fukuoka Municipal Transportation Bureau, Fukuoka (Japan); Yamauchi, Y; Imanishi, H [Osaka Soil Test, Osaka (Japan)

1996-10-01

For the foundation improvement works by grouting in a borehole, evaluation of grouting effect is one of the most important management items. The grouting design and works are sometimes reconsidered depending on the evaluation of grouting effect during the test injection. The purpose of the evaluation of grouting effect is to grasp the range of improvement and consolidation after the injection, and to judge and estimate the strength and permeability of the consolidation part. This paper describes the judgment method of the strength using PS logging results and borehole televiewer (BHTV) logging results. The reflection intensity (Ir) by the BHTV logging increased after the grouting, which showed a same tendency as that using S-wave and P-wave velocities (Vs and Vp) before and after the grouting. This was considered to demonstrate the grouting effect. A relation was obtained between the Vs, Vp and Ir before and after the grouting, which was expressed by following equation. Ir=0.143{times}Vs-70=0.093{times}Vp-110. The relation with the dynamic elastic coefficient (Ed) was also obtained as follow; Ir=0.0013{times}Ed. 9 figs.

Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-10-01

Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

Study of design factors of vehicle headlamp control systems; Zenshoto seigyo system no hyoka shuho no kento

Energy Technology Data Exchange (ETDEWEB)

Kamishima, H; Miwa, T; Sasaki, T; Imai, M [Nissan Motor Co. Ltd., Tokyo (Japan); Sumi, T [Niles Parts Co. Ltd., Tokyo (Japan)

1997-10-01

The on-and-off timing of vehicle headlamp control systems varies with weather conditions. Cloudy weather has a wider light energy distribution from visible to infrared radiation than clear weather. Silicon photodiodes, which can detect visible to infrared radiation, have larger output currents on cloudy evenings than on clear evenings under the same brightness conditions. The systems should be designed with such factors in mind as spectral characteristics of windshield, filters, sensor, and eyesight. 4 refs., 9 figs.

Study on water desalination system by solar energy distillation; Taiyo energy wo riyoshita joryugata kaisui tansuika system no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nagai, M; Ameku, K; Yonamine, K [Univ. of the Ryukyus, Okinawa (Japan)

1997-11-25

Discussions have been given on developing a seawater desalination system by solar energy distillation. The system is composed of evaporators installed on the seawater level, condensers placed on high and cool locations, and steam transport pipes to connect these two pieces of equipment. Steam is generated from seawater heated by solar heat in evaporators, and the steam is transported driven by low power consuming fans to higher locations through the steam transport pipes, where it is condensed by cool air in the condensers, and recovered as plain water. The concept is such that electric power required to operate the fans is supplied from photovoltaic panels, and all other energy is obtained from the sun. First, an experiment was performed upon noticing on methods of transporting and condensing the steam. The experiment used plain water rather than seawater. The heat source and evaporators were installed on the first floor, and the steam transporting fans on the second floor of an atrium. The thermal load was set to 1.5 times greater than average outdoor insolation amount. Increase in the distilled water recovery rate and distillation efficiency was verified by using the fans. The evaporation efficiency was found to tend to increase when the steam flow rate is increased. 3 refs., 10 figs.

On practicality of a hybrid car with solar cells; Taiyo denchi wo tosaishita hybrid car no jitsuyosei ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Sasaki, K; Nagayoshi, H; Kamisako, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1997-11-25

The paper stated a development of a hybrid car which is a parallel type with gasoline engine and electric motor as driving source (connecting each according to the situation) and is also equipped with solar cells. Specifications are gasoline engine of 1200cc, induction motor of 5.5kW, lead battery of 288V and 7.2kWh, monocrystal silicon solar cells of 180W maximum output, and body weight of 1100kg. The rear wheel is driven by electric motor, and the front wheel by gasoline engine. The car is loaded with battery charge use solar cells on hood and roof. To enhance cleaning degree, 1.6kW solar cells are installed as an installed power system and used for battery charge. Even by an electric motor with output less than that of the usual electric car, harmful exhaust gas emitted in start-up can be controlled. This is because the electric motor can be used in accelerating. It was confirmed that the power required for it could be supplied by solar cells installed on the car. The hybrid car is practically useful for prevention of local air pollution. 5 refs., 4 figs., 2 tabs.

Influence of angle of inclination on power of solar module; Taiyo denchi module no keisha kakudo to shutsuryoku tokusei

Energy Technology Data Exchange (ETDEWEB)

Tsutsumi, K.; Nishitani, M. [Dai Ichi University, College of Technology, Kagoshima (Japan)

1997-11-25

Experiment/study were conducted on the influence of angle of inclination on output of solar modules. In the experiment, changing the angle of inclination of the photovoltaic module installed on the top of school building to 0, 30, 60 and 90 degC, the global radiation on an inclined surface was measured by pyranometer equipped with the module, and at the same time output characteristics were measured by I-V curve tracer. In the I-V curve tracer, voltage, current, and output capability diagram are illustrated automatically changing bias voltage to get the maximum output. The global radiation on an inclined surface and the maximum output indicated an almost proportional relation and were expressed in a recursion method. Moreover, measurement of the global radiation is usually conducted using the amount of global radiation on a horizontal surface, and the global radiation on an inclined surface is calculated as a sum of the direct solar radiation amount and the sky solar radiation amount after determining a penetration rate by the relational equation. By calculating the global radiation on an inclined surface, it becomes possible to calculate the maximum output of photovoltaic modules by this recursion method. 1 ref., 6 figs., 1 tab.

Research and development of the industrial basic technologies of the next generation, 'composite materials (quality evaluation techniques)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (hinshitsu hyoka gijutsu)'. Zenki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The results of the first phase research and development project for developing composite materials as the basic technologies of the next generation are evaluated, and the directions of the R and D evaluation for the second phase are set up. The efforts in the first-phase R and D project are aimed at development of methods for measuring carbon fiber surface structure elements; confirmation of the relationship between adhesive shear strength and active surface area; development of methods for determining fracture toughness by standard specimens; estimation of allowable void fraction for inter-layer shear strength; defect detection and quality evaluation by electromagnetic, ultrasonic, laser holography and AE methods; development of methods for detecting resin setting reactions during the molding processes; and understanding deteriorated mechanical characteristics of the resin-based composites by environmental factors, among others. The objectives of the first-phase project have been almost achieved. It is decided that the second-phase R and D project are directed to investigations on the relationship between surface properties of the fibers in the composites and fiber/matrix adhesion; researches on mechanical characteristics involved in fracture of the structural elements; evaluation of mechanical properties of the metal-based composites and investigations on detecting their defects; elucidation of the effects of environmental factors on their strength; and development of the techniques for integrating detection of molding-induced cracking and that of setting reactivity, among others. (NEDO)

What will be brought about by changes in evaluation standards; Kachi hyoka kijun no henka ga motarasu mono

Energy Technology Data Exchange (ETDEWEB)

Hasegawaa, J. [Hokkaido University, Sapporo (Japan)

1999-12-17

The author expresses his opinion toward the impact to be brought about by changes in evaluation standards mainly involving the power system. The 20th century has been an age of mass production of various articles and mass consumption of various resources. It has become evident of late that flexibility, which will realize environmental impact reduction and satisfy varying needs, should be added to the evaluation standards. The new evaluation standards urge that the large-scale centralized management type system be converted into an autonomous distributed type system, and mass production into small-scale production of multiple articles. The development from centralization to decentralization, and the trend toward deregulation and the corporation's plan of dividing itself into plural in-house companies, may be evaluated against the same context. In the field of power systems, it is deemed that the diffusion of power retailing business and distributed power sources will be accelerated. When it comes to a power system constitution and operation capable of dealing with the new development, an autonomous distributed type system constitution and operation as a local energy system is supposed to be more appropriate than the conventional centralized management type. (NEDO)

Report on the environmental safety evaluation sub-committee in fiscal 1992; 1992 nendo kankyo anzensei hyoka bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the environmental safety evaluation sub-committee for the coal liquefaction plant in fiscal 1992. The sub-committee, upon having received reports on the result of environmental safety evaluation tests performed in fiscals 1991 and 1992 by NEDO, deliberated and discussed carefully the contents thereof. In order to ensure labor hygiene for coal liquefaction plant workers, health influence on liquefied oil users, and social acceptability of the liquefied oil, NEDO has performed the comprehensive brown coal pilot plant operation and oil safety tests. The tests are in accordance with the labor safety and hygiene law, the chemicals examination law, and the MPD issued by OECD, and performed on each fraction produced in the pilot plant and the whole fraction mixing the former fractions, using rats, rabbits, and guinea pigs. The test items included: acute inhalation toxicity and oral repeated administration (using rats); eye stimulation, repeated coating and skin stimulation (using rabbits); photo-toxicity (using guinea pigs); mutagenicity tests (microorganisms, bacteria and chromosome anomaly); resolution tests; fish toxicity; concentration degrees; algae growth obstruction; and water flea breeding obstruction. As the result, the toxicity was found light. (NEDO)

Evaluation of permeability of Nojima fault by hydrophone VSP; Hydrophone VSP ni yoru Nojima danso no tosuisei hyoka

Energy Technology Data Exchange (ETDEWEB)

Kiguchi, T; Ito, H; Kuwahara, Y; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)

1996-05-01

The multi-offset hydrophone VSP experiments were carried out using a 750m deep borehole as the oscillation receiver, which penetrates the Nojima fault, to detect water-permeable cracks and evaluate their characteristics. Soil around the borehole is of granodiorite, and fault clay is found at a depth in a range from 623 to 624m. A total of 4 dynamite tunnels were provided around the borehole as the focus. The VSP results show that the tube waves are generated at 22 depths, including the depth at which fault clay is found. However, these waves are generated at only 6 depths in an approximately 150m long fracture zone, suggesting that the cracks in the zone are not necessarily permeable. It is also found that crack angle determined by the analysis of tube waves almost coincides with that of fault clay determined by the core, BHTV and FMI, and that permeability is of the order of 100md at a depth of fault clay or shallower. 3 refs., 2 figs., 2 tabs.

Development and applicability estimation of the tire contact pressure measurement system; Tire secchiatsukei no kaihatsu to oyosei hyoka

Energy Technology Data Exchange (ETDEWEB)

Mizutani, Y.; Amago, T.; Takahashi, T.; Sakuma, S.; Mori, N. [Toyota Central R and D Laboratories, Inc., Aichi (Japan); Nagae, A. [Toyota Motor Corp., Aichi (Japan); Yasuoka, M. [Toyo Tire and Rubber Co. Ltd., Osaka (Japan)

1995-04-20

A pressure sensor more reliable than the conventional types and a tire pressure measurement system using a plurality of sensors of the said reliable type have been developed. The sensor is an inverted T in shape, the upper surface of the vertical beam thereof receives the pressure, and the two ends of the horizontal beam are fixed. The load per unit area imposed on the pressure receiving surface is separated into three components, the X and Y components in the tangential direction are sensed by the vertical beam while the Z component in the vertical direction is sensed by a distortion gauge attached to the horizontal beam. For the measurement of the contact pressure distribution for the entire contact surface, a measuring device was developed, comprising a multiple point contact pressure gauge with 30 sensors of the reliable type discussed here embedded therein, a tire rolling tester, and a data processing unit. A tire wear estimation test was conducted using this pressure sensor and a contact probe type slip sensor, and it was found that a tire of a greater friction energy ratio is easier to experience abnormal abrasion and that the new pressure sensor is useful in estimating abnormal abrasion. Further, it was indicated that the present measuring device is applicable to the analysis of the mechanism wherein shaft force results from contact pressure on the soil. 3 refs., 11 figs., 3 tabs.

Ecological processes for Environmental Impact Assessment in Coastal Waters; Engan no kankyo eikyo hyoka (EIA) eno seitaigakuteki apurochi

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, Kimitoshi. [Environmental Assessment Dept., Tokyo (Japan)

1999-03-25

This paper focuses on a method for estimating adverse effects on natural environment by economic development in coastal waters in Japan. In particular, the most critical relations concerning the impact on marine organisms is pointed out and discussed according to an environmental impact assessment. Relations between environmental impact assessment and marine organisms needs a quantitative ecological approach in order to succeed in sustainable development of coastal waters management. Recently, the Environment Agency of Japan pointed out the unreliability and the theme on accuracy and the staff for biology and ecology in the environmental impact study. Ecological response to environmental impact occurs in a wide spectrum of physiological and biological and biological functions. Therefore biological monitoring measures must correspond to the given time-space scale of natural mechanisms. For the evaluation of environmental impact, it is desire able to develop of experimental technics and collect biological and ecological basic data for the object. I Reconstructing the following: 1. Reconstructing a clearlistic EIA process by EIA agencies and practitioners, 2. Scorping the biological and ecological issues by EIA professionals, 3. Using the current computer technology, 4. Considering monitoring systems over scales of time and space for the ecological target and 5. Making available to public all monitoring data and reports of EIA. (author)

Application of cytotoxicity test for toxic micropollutants. Saibo dokusei shiken ni yoru yugai kagaku busshitsu osen no hyoka

Energy Technology Data Exchange (ETDEWEB)

Utsumi, H; Hamada, A [Showa University, Tokyo (Japan). School of Pharmaceutical Science; Ono, Y [National Institute of Hygienic Sciences, Tokyo (Japan)

1992-10-01

Considerations were given from a viewpoint of assessing toxicity to human bodies on methods of assessing water pollutants and organisms, and applicability of cytotoxity test using cultured cells to water quality assessment. Biological assessment systems used for water environment may use tests using multicellular organisms, cells, or organelles in cells. The organism assessment method is intended mainly for assessing ecological effects, and a suitable method must be selected upon extrapolating it to human bodies. A toxicity parameter used most frequently in a cytotoxity test is the cell revival rate, and life and death are determined from liberation of enzymes in cells, or with color rejection tests and incorporation tests. There are a number of test specimens of raw tap water and its chlorine treatment condensate that show no mutagenicity but cytotoxity. Efficiencies of removal by means of mild chlorine treatment, fast filtration, and activated carbon adsorption vary greatly with cytotoxity and mutagenicity. Introducing the cytotoxity test is expected of further contributing to improving safety in water quality. 24 refs., 1 fig., 7 tabs.

Fracture mapping in rock slope using geophysical instruments; Butsuri tansa ni yoru ganban shamennai no kiretsu bunpu hyoka

Energy Technology Data Exchange (ETDEWEB)

Kurahashi, T; Inazaki, T [Public Works Research Institute, Tsukuba (Japan); Watanabe, S [Geological Survey of Japan, Tsukuba (Japan)

1997-05-27

An attempt was made to visualize distribution of cracks in a rock slope by applying geophysical survey onto a rock slope. Geophysical logging and seismic survey using the reflection method were used as the methods for the geophysical survey. The rock slope subjected to the survey is located in a gorge along the Yoshino river in Yamashiro Town, Tokushima Prefecture. The slope has a width of 25 m and a height of 30 m. Its overhang in a nose form may has a possibility of causing collapse due to sliding. Cracks developed by horizontal schistosity were detected by performing geophysical logging on VSP, calipers, natural gamma-ray spectra, temperature and borehole in a borehole drilled vertically from the top of the slope. The seismic survey using the reflection method detected the cracks by emphasizing joints in the perpendicular direction. A possibility was shown to visualize the crack distribution with high resolution by using the above geophysical survey on the rock slope. In order to detect the crack distribution with still higher resolution, development into a three-dimensional exploration in the future is desired, not to speak of improvement in signal receivers, and discussions on geometry. 1 ref., 6 figs.

Evaluation of the prevention potential against landslide disasters. Jisuberi saigai wo taisho to shita bosai potential no hyoka

Energy Technology Data Exchange (ETDEWEB)

Umemura, J [Nihon University, Tokyo (Japan). College of Engineering; Hayashi, S; Ochiai, H [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1994-03-21

In order to evaluate disaster potential and disaster prevention potential of landslides, which are complicatedly composed of natural factors and social ones, an evaluating method of the potentials is proposed by applying the multiple logistic model. Furthermore, a method making the potential map using this evaluation is shown. The multiple logistic model is based on the conception of multiple risks, and so the disaster potential is expressed with probability. The disaster prevention potential is evaluated by using the disaster potential. Taking a typical landslide district as an instance, some potential maps colored by each potential are shown. By these maps, effects of the preventive measures against disasters and changes in the disaster prevention potential according to the industrial structure as well as the population are evaluated. Furthermore, combination of the other disaster potentials obtained by changing the surveying interval or factors makes it possible to draw various disaster maps and disaster prevention ones for different purposes. 15 refs., 17 figs., 3 tabs.

Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

Primary study on quantitative evaluation of driver fatigue; Unten hiro no teiryo hyoka gijutsu ni kansuru kiso kento

Energy Technology Data Exchange (ETDEWEB)

Noguchi, Y; Mochizuki, M; Toyofuku, K [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Katsuura, T [Chiba University, Chiba (Japan)

1997-10-01

Quantitative evaluation of physical and mental loads are effective in developing more human-friendly vehicles. Here attention has been focused on the mental load. Attempts were made to find some physiological indices that can be used for quantifying the mental load and resultant fatigue. Subjects were told to perform three different tasks in a climatoron, and the relation between physiological indices and their perception of fatigue as well as their capability of performing the tasks were analyzed. As a result, heart rate variability is a good index for quantitative evaluation of mental load and fatigue. 5 refs., 4 figs., 6 tabs.

Development of electrostatic charging evaluation equipment for automobile seat; Jidoshayo seat no taidensei shiken hyoka sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Maeda, K [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

When passengers get out of vehicle, electrostatics is generated by separation of seat cloth and passenger cloth, and then charged to passenger`s body. It has been impossible for us to simulate this induction charging phenomenon with current evaluation equipments. We developed a new seat cloth evaluation equipments using induction charging plate, which enables us to simulate the phenomenon. This paper describes this new electrostatic charging evaluation method for automobile seat cloth. 5 refs., 6 figs.

A Probabilistic Tsunami Hazard Assessment Methodology and Its Application to Crescent City, CA

Science.gov (United States)

Gonzalez, F. I.; Leveque, R. J.; Waagan, K.; Adams, L.; Lin, G.

2012-12-01

.I., E.L. Geist, B. Jaffe, U. Kânoglu, H. Mofjeld, C.E. Synolakis, V.V Titov, D. Arcas, D. Bellomo, D. Carlton, T. Horning, J. Johnson, J. Newman, T. Parsons, R. Peters, C. Peterson, G .Priest, A. Venturato, J. Weber, F. Wong, and A. Yalciner (2009): Probabilistic Tsunami Hazard Assessment at Seaside, Oregon, for Near- and Far-Field Seismic Sources, J. Geophys. Res., 114, C11023, doi:10.1029/2008JC005132. Japan Earthquake Research Committee, (2011): http://www.jishin.go.jp/main/p_hyoka02.htm Mai, P. M., and G. C. Beroza (2002): A spatial random field model to characterize complexity in earthquake slip, J. Geophys. Res., 107(B11), 2308, doi:10.1029/2001JB000588. SSHAC (Senior Seismic Hazard Analysis Committee) (1997): Recommendations for Probabilistic Seismic Hazard Analysis: Guidance on Uncertainty and Use of Experts, Main Report Rep. NUREG/CR-6372 UCRL-ID-122160 Vol. 1, 256 pp, U.S. Nuclear Regulatory Commission.

Technological development for super-high efficiency solar cells. Technological development of solar-high efficiency singlecrystalline silicon solar cells (high quality singlecrystalline silicon substrates); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (kohinshitsu tankessho silicon kiban no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development for high quality efficiency singlecrystalline silicon substrates in fiscal 1994. (1) On electromagnetic casting/once FZ bath method, a Si single crystal of 600mm long was successfully obtained by improvement of power source frequency and furnace parts. High carbon content resulted in no single crystal including solids. In undoped electromagnetic casting ingots, resistivities over 1500ohm-cm were obtained because of effective preventive measures from contaminants. (2) On electromagnetic melting CZ method, since vibration and temperature control of melt surface by magnetic shield was insufficient for stable pulling of single crystals, its practical use was hopeless. (3) On electron beam melting CZ method, a Si single crystal of 25mm in diameter was obtained by preventive measures from evaporation of Si and influence of deposits, and improved uniform deposition distribution in a furnace. The oscillation circuit constant of power source, and water-cooling copper crucible structure were also analyzed for the optimum design of electromagnetic melting furnaces. 3 figs., 1 tab.

Achievement report on Sunshine Program research and development for fiscal 1981. Research and development of amorphous solar cells (Research and development of integrated type amorphous solar cells); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Shusekigata amorphous taiyo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

An a-SiC (amorphous SiC) material with a wider band gap adds to the conventional hydrogen- and fluorine-based a-Si materials in the study for device efficiency enhancement, and the a-SiC is found suitable as a wide-gap window material. The separated formation technique is found to work effectively for improvement on cell characteristics because it prevents the mixing of impurities of different types. A p-i-n (positive-intrinsic-negative) type amorphous solar cell is subjected to analysis, and a theoretical efficiency of 12.5% is obtained in photoelectric conversion. A conversion efficiency not less than 7% is obtained from an ITO (indium-tin oxide)/p(SiC)-i-n/Al cell on a glass substrate. Design is optimized for area enlargement for an integrated type device, which results in an experimental 10cm-square integrated type solar cell with a conversion efficiency of not less than 5%. As for modularization, a glass substrate for integrated type device is used, as is, as a light-receiving surface protecting board, and studies are conducted thereon. It is then found that the amorphous solar cell experiences some degradation in reliability at the beginning of an irradiation test but that no extensive degradation in reliability is observed even after the passage of 1,000 hours from the beginning of the test. The separated formation technique is found suitable for use in mass production. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program survey and research. Joint projects on solar energy between Japan and Australia, etc. (Japan-France technological cooperation on solar energy); 1981 nendo Nichigo nado taiyo energy gijutsu kyoryoku jigyo seika hokokusho. Nichifutsu taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

A curved-surface thermal power system just before completion is visited, located on the island of Corsica. Light is collected by a curved-surface mirror in which narrow flat-surface mirrors with their length matching the linear collector width are attached amphitheater-wise to a curved-surface foundation built of concrete, and a linear collector performs tracking along the focal line. Exchange of information and comparative study will be required concerning this system. As for passive use of heat, a flat-plate collector has reached a level of practical application at homes in the low-temperature domain. Sites related to long-term basic research and seawater desalination are also visited. As for collector in the high-temperature domain, a THEK (Thermo-Helio-Electricity Kilowatt) system which is a spherical mirror collector is on the initial stage of planning. It is important to compare various types of curved-surface systems for their merits and demerits. As for the production of solar cells for photovoltaic power generation, it is monopolized by the Photowatt Corporation, with most of the products to be exported for use as independent power sources. As for future development, the casting technique will be industrialized at the end of 1983, the ribbon type will come next, and the amorphous material will be farther in the future. The task is how to enhance technical cooperation in the future. (NEDO)

PREFACE: International & Interdisciplinary Workshop on Novel Phenomena in Integrated Complex Sciences: from Non-living to Living Systems

Science.gov (United States)

Yoshimura, Kazuyoshi; Ohta, Hiroto; Murase, Masatoshi; Nishimura, Kazuo

2012-03-01

(Institute for Complex and Adaptive Matter, USA), Yukawa Institute for Theoretical Physics (Kyoto University), Institute of Economic Research (Kyoto University) and Kyoto University GCOEs (Global Centers Of Excellence: Physics, Chemistry, and Economics). The workshop was also supported by Niki Glass Company Ltd., THAMWAY Corp., TAIYO NIPPON SANSO, and Quantum Design Japan. The Editors and the Organizing Committee, Masatoshi Murase Kyoto University, Japan Kazuo Nishimura Kyoto University, Japan Kazuyoshi Yoshimura Kyoto University, Japan: Conference Chairman and Chief Editor Hiroto Ohta Kyoto University, Tokyo University of A&T, Japan: Conference Secretary Conference Photograph, 14 October 2010 Conference Photograph Conference Poster Conference Poster

Ionospheric data for two solar cycles available online

International Nuclear Information System (INIS)

Bilitza, D.; Papitashvili, N.; Grebowsky, J.; Schar, W.

2002-01-01

We report about a project that has as its goal to make a large volume of ionospheric satellite insitu data from the sixties, seventies and early eighties easily accessible for public use The original data exist in various machine-specific, highly compressed, binary encoding on 7- or 9-track magnetic tapes. The intent is to decode the data format and convert all data sets to a common ASCII data format and add solar and magnetic indices for user convenience. The original intent of producing CD-ROMs with these data has meanwhile been overtaken by the rapid development of the internet. Most users now prefer to obtain the data directly online and greatly value web-interfaces to browse, plot and subset the data. Accordingly, the focus has shifted to making the data available online on the anonymous ftp site of NASA's National Space Science Data Center (NSSDC) at ftp://nssdcftp.gsfc.nasa.gov/spacecraft data/ and on the development of a web-interface (ATMOWeb, http://nssdc.gsfc.nasa.gov/ atmoweb/) to help users study the data and select interesting time periods. The data considered by this project include data sets from the Alouette I, BE-B (Explorer 22), Alouette 2, DME-A (Explorer 31) , AE-B (Explorer 32), AE-C, -D, -E, OGO-6, ESRO-4, ISIS-I, -2, AEROS-I, -2 Taiyo, ISS-b, Hinotori and DE-2 satellites. The data are primarily electron and ion densities and temperatures measured by Langmuir Probes (LP), Retarding Potential Analyzers (RPA), and Ion Mass Spectrometers (IMS) flown on these satellites. The time resolution of the measurements is typically seconds to minutes. This data base covering almost two solar cycles is a unique asset for studies of the variation and variability of ionospheric parameters. It will be an important element in the quest for a better understanding of ionospheric plasma processes and for improved predictions of ionospheric Space Weather. Current models are still very limited in their predictive capabilities especially at equatorial and auroral

Influence of spectral solar radiation to the generating power of photovoltaic module; Taiyo denchi shutsuryoku eno taiyoko supekutoru eno eikyo

Energy Technology Data Exchange (ETDEWEB)

Minaki, S.; Ishihara, Y.; Todaka, T.; Harada, K. [Doshisha University, Kyoto (Japan); Oshiro, T.; Nakamura, H. [Japan quality Assurance Organization, Tokyo (Japan)

1997-11-25

As to the influence of spectral solar radiation to generating power of solar cells, a study was conducted from the aspects of season, time zone, intensity of solar radiation, etc. In the study, spectral responsive variation correction coefficients were introduced as evaluation values expressing the influence of spectral solar radiation. For the spectral distribution, an all sky spectral pyranometer by wavelength was used, and data were used which were obtained in the measurement in experimental facilities of the solar techno center. Concerning solar cell relative spectral sensitivity values, used were relative spectral sensitivity values of monocrystal and amorphous standard solar cells to the short-circuit current. Spectral response variation correction coefficients are coefficients correcting variations in conversion efficiency of solar cells due to changes in the spectral distribution. The changes of spectral responsive variation correction coefficients were studied using data obtained during April 1994 and March 1996. As a result, it was found that the coefficients showed large changes in summer and small ones in winter and that amorphous solar cells indicate this trend conspicuously. 3 refs., 6 figs., 3 tabs.

Summary of reports on 1979 result of Sunshine Project. Solar energy; 1979 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-04-01

This report is a compilation of all outlines of the results concerning 'solar energy' for which R and D was carried out as a part of Sunshine Project in fiscal 1979. The research subjects (items of the studies) are written below. 1. Solar energy system (measurement of spectral irradiance, utilization system, and meteorological investigation); 2. Solar thermal power generation system; 3. Photovoltaic power generation system (basic research on solar cells, silicon vertical ribbon crystal, silicon horizontal ribbon crystal, particle non-acceleration growth type thin film silicon crystal, particle acceleration growth type thin film silicon crystal, new type solar cells, secondary to quaternary compound semiconductor solar cells, and photovoltaic power generation system); 4. Solar cooling, heating and hot water supply system (evaluation system, newly-built private residential system, existing private residential system, multiple dwelling system, large building system, synthetic resin materials, glass based materials, and metallic materials); 5. Solar energy new utilization method (new power generation system and materials); 6. R and D on solar thermal power generation plant (R and D on pilot plant, experimental research for developing plant on curved surface converging method, and experimental research for developing plant on tower converging method). (NEDO)

Indirect solar-pumped laser diode using a solar cell; Taiyo denchi wo mochiita taiyoko kansetsu reikigata handotai laser no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kanamori, Y.; Yugami, H.; Naito, H.; Arashi, H. [Tohoku University, Sendai (Japan). Faculty of Engineering

1996-10-27

This paper describes the operating characteristics of a stabilizing circuit using commercial electricity, those of a stabilizing circuit using solar cells, relation between the quantity of solar radiation and the maximum output of a semiconductor laser diode (LD), and simulation results of annual LD output in Sendai City. The stabilizing circuit for the solar-cell driven LD was structured such that the output of the solar cell panels was guided to a DC/DC converter, that the voltage was set at a prescribed value and that the current was stabilized with the use of power MOSFET. The solar cells used in the experiment were monocrystal silicone solar cells with the maximum output of 53W each. In the experiment, the LD was protected by stabilizing the current at a set value when an excess current was supplied to the stabilizing circuit. As a result of the simulation of the annual LD output from the meteorological data of Sendai City, it was predicted that a solar cell of approximately 1kW was able to provide an annual output of 102MJ and that the efficiency was highest with four sheets of the solar cell. Consequently, consistency proved to be essential between the LD and the solar cell output. 3 refs., 7 figs.

Achievement report for fiscal 1999. Research on mesh-based estimation of natural energy for Southeast Asia as represented by Myanmar (Assessment of wind power and solar energy using numerical weather model); 1999 nendo Myanmar koku wo rei ni shita Tonan Asia ni okeru shizen energy no mesh suitei ni kansuru kenkyu seika hokokusho. Suchi kisho model ni yoru furyoku taiyo energy hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As the first step for the introduction of wind power systems and photovoltaic power systems into developing countries in Southeast Asia etc. and for their diffusion in them for the exploitation of natural energy, a numerical weather model useable in Southeast Asia is developed to make up for the insufficiency of weather data in the region. A technique is developed, to explain which the case of Myanmar is cited, for estimating with accuracy such natural conditions as wind direction, wind velocity, and solar radiation in the past one-year period for the assessment of power to be generated using wind turbines and solar panels. The results of the observation of wind conditions indicate that wind directions are mainly northerly or westerly and that wind speeds are as week as 1-3m/s on the average. As for total solar radiation per diem in December through March, it is found that there is 17-23MJ/m{sup 2}/day, which is twice the level to be measured in Tokyo. A comparison is made between the weather observation results and a model calculation, and it is found that the latter sufficiently reproduces the actual weather conditions. Based on the values of wind conditions and solar radiation estimated in Myanmar, the amount of power to be obtained from an assumed arrangement of wind power systems and solar panels is assessed. (NEDO)

Research on elaboration of the evaluation guidelines for activities implemented jointly; Kyodo jisshi katsudo hyoka guide line sakutei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Elaboration of the evaluation guidelines for activities implemented jointly (AIJ) was researched to prevent the earth from warming. AIJ is the means to globally promote countermeasures against global warming cost-effectively by optimally combining every country`s technology, know-how and fund. AIJ was established in the 1st Conference of the Parties (COPI) of the United Nations Framework Convention on Climate Change in March, 1995. The pilot phase of AIJ is first carried out by voluntary workers jointly with developing countries under the agreement of the parties. The current situation of activities is reported in COPI as materials for evaluation of AIJ. To promote AIJ, elaboration of the evaluation guidelines for AIJ Japan program is also necessary for Japan. This research arranged the contents of the evaluation guidelines and the method of classifying projects for AIJ Japan program, and carried out some case studies of promising projects to reduce greenhouse gas emission for future proposal. 3 figs., 31 tabs.

Report on the environmental safety evaluation sub-committee meetings in fiscal 1987; 1987 nendo kankyo anzensei hyoka bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The environmental safety evaluation sub-committee has held two meeting in the current fiscal year as described below. The first sub-committee meeting (August 25, 1987) was held for the agenda of the summary of future test plans, the result of overseas surveys in fiscal 1986, the results of tests in fiscal 1986, and the summary of the test plan for fiscal 1987. The major agendum of the second sub-committee meeting (February 23) was the interim reports on the overseas survey results and the safety tests in fiscal 1987. NEDO intends to ensure the labor hygiene for workers in coal liquefying plants, the effect of liquefied oil on users' health, and social acceptability of liquefied oil. Therefore, a safety test for liquefied oil in the primary hydrogenation process was performed provisionally on brown coal PP in the initial stage of operation, in addition to bituminous coal liquefied oil at the existing 1-t/d PDU. The main contents of the test performed by NEDO are based on the labor safety and hygiene law and the law related to regulation on the deliberation and manufacture of chemical materials. Different tests using guinea pigs were carried out on the total fraction mixed at the 1-t/d PDU, and each fraction of light and heavy oils, where the liquefied oil was verified to have minor degree of toxicity. (NEDO)

Evaluation of paramagnetic species in coals with iodine doping technique; Yoso tenkaho wo mochiita sekitanchu no jojiseishu no hyoka

Energy Technology Data Exchange (ETDEWEB)

Aizawa, S.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

1996-10-28

Electron paramagnetic resonance (EPR) of coals was considered by using iodine doping technique. Sub-bituminous coal (WA) and bituminous coal (UF) were used to observe EPR spectra using microwaves. With the UF coal, strength of the narrow component of the spectra was found constant regardless of amount of the doped iodine, wherein radicals without interaction with iodine were detected. Strength of the broad component increased with the iodine doping amount, where in deviation of {pi} electrons was detected, which have been generated as a result of interaction between aromatic rings and iodine in the coals. Spin concentration of the WA coal with low coalification degree is constant regardless of the iodine doping amount, and the interaction of the iodine with the aromatic rings was found small. The higher the coalification degree, the more the aromatic ring structure grows, and electron donor capability for the iodine increases. In a system with the entire spin being uniform, the spectrum height shows a saturation phenomenon against increase in microwave output. A non-uniform system, in which the oriented spin forms small groups and is in local thermal equilibrium, does not show saturation, but increases monotonously. 2 refs., 5 figs.

Evaluation of column flotation results with a film flotation method; Film fusenho wo mochiita column fusen kekkan no hyoka

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, H.; Matsukata, M.; Ueyama, K. [Osaka University, Osaka (Japan). Faculty of Engineering Science

1996-10-28

Change in wettability of coal particle surfaces due to kerosene adsorption was studied by using a film flotation method. The applicability of a film flotation method to coals modified by kerosene adsorption was first confirmed. In experiment, film flotation was applied to Illinois coal modified by aqueous methanol solution and kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface and kerosene in aqueous methanol solution were analyzed to verify the applicability of a film flotation method. Film flotation was applied to Datong and Illinois coals modified by kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface was plotted to surface tension of liquid. As a result, the weight percent of hydrophobic particles within 50mN/m in surface tension slightly increased in Datong coal and remarkably increased in Illinois coal with kerosene addition. It was thus suggested that in addition to surface tension, the distributions of hydrophilic and hydrophobic strengths on the surface of each coal particle should be considered to understand attachment of coal particles and bubbles. 6 refs., 4 figs.

Investigating the effect of aeration powder filling on the actual compacting press; Eareto jutenho no jikki press deno hyoka

Energy Technology Data Exchange (ETDEWEB)

Kondo, M. [Toyota Central Research and Development Labs., Inc., Nagoya (Japan); Urata, I. [Toyota Motor Co. Ltd., Aichi (Japan)

1998-05-15

The authors proposed an aeration filling method as a new filling method in order to obtain uniform and high speed filling by carrying out basic experiments on powder material filling using a visual apparatus. In this study, the aeration powder filling was applied to the product compacting on the actual compacting press, and its evaluation was carried out. As a result, the following effects were confirmed. The weight scattering was reduced to about 70% in the high speed filling and about 50% in the low speed filling. The maximum density was reduced to about 30% in the high speed filling and about 25% in the low speed filling. The maximum thickness difference was reduced to 65% in the high speed filling and about 20% in the low speed filling. The aeration powder effect was stronger in the high speed filling than that in the low speed filling. The weight and size accuracy of the components were increased by the aeration powder filling. The pause and the shaking operation were discarded in the front part of the powder box, thus the filling time could be remarkable shortened. 3 refs., 6 figs.

Survey of an evaluation method for research and development projects; Kenkyu kaihatsu project no hyoka shuho ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes an interim evaluation method and a concrete evaluation method for projects promoted by the Agency of Industrial Science and Technology, and NEDO. As a result of the survey, a method of highly practical interim evaluation, concrete evaluation items, and evaluation criteria have been proposed by assuming that the projects are evaluated by the project evaluation department independent of the project promotion department. Long-term issues for constructing the evaluation system are also described. It is the most essential for the evaluation to fulfill the function of effective promotion of the following projects. It is also indispensable for the evaluation method and issues proposed in this report to communicate closely to project promoters and researchers, and to reassess the projects continuously. Continuous consideration for the feedback of evaluation process and the improvement of evaluation are significant for the long-term construction of system. 21 refs., 9 figs., 23 tabs.

Microbiological indicators for evaluating treatability on water purification process. Josui shori ni okeru shorisei hyoka kara mita biseibutsu shihyo

Energy Technology Data Exchange (ETDEWEB)

Ichikawa, H [Kanagawa Prefectural Government Public Enterprise Egency Water Works Bureau, Kanagawa (Japan). Tanigahara Purification Plant

1990-08-10

This report describes the historical procedure of a bacterial test for a certain respective bacteria, and also describes the removal of micro-organisms by a water treatment and treatment with disinfectants. The disinfection is made mainly on basis of foreign literature. This is because there exist few literature published in Japan. In a good sense, this is because of the Japanese habit of drinking raw water which has contributed to high level of facilities and the maintenance. If seen from a different viewpoint, the prsent concern is concentrated to a contamination of the underground water by organic solvent and the counter measure against such minute quantity of organic chemicals as trihalomethane and the agricultural chemicals in the golf courses. From the consumers {prime} standpoint, these are of the level of problems that only one affected person increases per year for 100,000 inhabitants even if they continue to drink such drinking waters continuously through their life years. The reality is that it is remote from the realities in life. 37 refs., 9 tabs.

Evaluation on lifetime risk in reinforced concrete structure; RC kozo no lifetime risk no hyoka ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, M. [Public Works Research Institute, Tsukuba (Japan); Adachi, H. [Taisei Corp., Tokyo (Japan); Akakura, Y. [Ministry of Transport, Tokyo (Japan); Ibayashi, K.; Ozaka, Y. [Tohoku Gakuin Univ., Sendai (Japan)

1996-02-15

To evaluate the risk during longevity of reinforced concrete structure subjected to earthquake motions, called lifetime risk, damage and safety were estimated by means of the earthquake risk analysis and earthquake response analysis. For the earthquake risk analysis, historical earthquake data with relatively low accuracy were efficiently taken into account, to determine the annual mean generation probability against the earthquake motion strength in ten main cities. A new damage index with load hysteresis was defined as an anti-earthquake evaluation index where accumulative damage is taken into consideration. Assuming that the damage transits from `certain state` to `certain state` every time the earthquake motion generates at the noticeable place, damage transition matrix expressing transition probability was calculated by using the results of earthquake risk analysis and the accumulative damage index. The lifetime risk was calculated from the damage transition matrix and the earthquake motion generation probability, to evaluate the safety. 21 refs., 10 figs., 8 tabs.

Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of solar energy technologies (Research and development of SnO{sub 2} solar cells); 1981 nendo taiyo energy gijutsu no kenkyu kaihatsu seika hokokusho. SnO{sub 2} taiyo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

The aim is to establish the technology of manufacturing SnO{sub 2}/nSi solar cells using a low-temperature deposition method and thereby to reduce the cost. A 5cm-diameter wafer is subjected to a batch process, and a large-area, uniform-quality SnO{sub 2} film is obtained. A conversion efficiency of 13.7% is achieved for a single-crystal 9cm{sup 2} cell. As for the conditions of electrode formation, conventional methods are applied for bonding metals, which are Sn, Ni, Zn, etc., for the surface electrode and rear electrode. Vapor deposition is found to be the most excellent. Since it is known that ohmic characteristics improve when Cr is inserted as the base for the surface electrode rear electrodes, it is anticipated that a contact resistance value not inferior to that by vapor deposition will be achieved once the method of Cr bonding, whether by printing or plating, is established. An n-type low-cost polycrystalline Si substrate is subjected to etching under the optimum conditions, and a conversion efficiency of 9.6% is achieved for a 0.5cm{sup 2} cell. An SnO{sub 2} film is formed on a uneven surface for a reduction in the single-crystal cost, when characteristics better than those of a wafer manufactured by surface polishing are realized. Experimentally produced cells are evaluated using a solar simulator, and the result indicates that the electrode forming conditions influence conversion efficiency a great deal. (NEDO)

Achievement report for fiscal 1983 on Sunshine Program-entrusted survey and research. Cooperative project between Japan and Australia, etc., on solar energy technology (Cooperation between Japan and France on solar energy technology); 1983 nendo Nichigonado taiyo energy gijutsu kyoryoku jigyo seika hokokusho. Nichifutsu taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

This paper reports a survey on solar heat utilization technologies conducted in fiscal 1983 in accordance with a scientific cooperation agreement signed by the Japanese Government and the French Government. The survey was carried out by two employees with the solar technology development office of the New Energy and Industrial Technology Development Organization who were dispatched to France on a tour in the period March 13-24. Concerning the 'French Photovoltaic Program 1982-1986,' knowledge on the goal of the program, long-term research and development, and budgetary matters were obtained at the AFME (French Energy Management Agency) head office and its branches. Relations of AFME with EC (European Community) projects were clarified. The photovoltaic power system (50kW) of Nice Airport is one of the EC projects, and was built thanks to financial aids by EC and AFME. The power system is now in service as a power source for electronic equipment in the airport management building and for taxi lights installed on the ground. The CGE (Compagnie General d'Electricite) central laboratory and the Rhone Poulenc Specialites Chimique were visited, when information on the research and development of a ribbon crystal pulling process and solar-grade silicon was acquired. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of high-quality amorphous material/substrate manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A microcrystalline Si thin film is used to form the i-layer of a narrow gap a-Si based thin film solar cell. Since a microcrystalline p-layer is to act as the seeding crystal layer for the microcrystalline i-layer, it has to be very high in crystallinity and therefore is produced under high hydrogen dilution conditions. In this process, a problem arises of the darkening of the underlying transparent SnO{sub 2} electrode. Since this is due to chemical reaction on the SnO{sub 2} surface layer, blackening is prevented by shortening the film fabrication time, and then an excellently microcrystalline p-layer is obtained. Furthermore, by inserting a microcrystalline i-film buffer layer of low fabrication rate into the p/i boundary, plasma damage on the microcrystalline p-layer is inhibited for the fabrication of a microcrystalline i-layer high in crystallinity at high film fabrication rates. A high Voc is then obtained even when the microcrystalline p-layer is very thin. If the hydrogen dilution rate is too low when the i-layer film fabrication rate is high, the initially fabricated layer turns out to be thick to the detriment of film performance. On the other hand, the p-layer or the buffer layer will be etched when the hydrogen dilution rate is too high. The problem is solved by continuously varying the hydrogen dilution rate from high to low during i-layer fabrication. (NEDO)

FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for fabrication of thin-film solar cells/materials and substrates (Development of technologies for fabrication of high-quality amorphous materials and substrates); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for the amorphous/microcrystalline solar cells with the thin microcrystalline silicon film as the i layer, and the FY 1999 results are reported. The fabrication technologies are investigated for the microcrystalline silicon solar cells of pin or nip structure by RF or VHF plasma CVD using SiH{sub 4} and H{sub 2} as the stock gases. The tests are conducted for evaluating characteristics of the thin microcrystalline silicon film, to investigate the effects of film-making pressure, power and hydrogen dilution rate on the characteristics at a constant film-making temperature of 180 degrees C. The researches on the fabrication technologies for the microcrystalline solar cell of pin structure confirm that use of VHF plasma CVD improves crystallinity, electrical and optical characteristics of the p-type thin microcrystalline silicon film. The researches on the fabrication technologies for the microcrystalline solar cell of nip structure covers transparent substrates, film-making speed of the p layer, power and substrates, and a conversion efficiency of 7.5% is realized by the solar cell formed on a texture substrate. (NEDO)

Temperature dependence of the early degradation in a-Si solar cells; Amorphous Si taiyo denchi no shoki rekka no ondo izonsei

Energy Technology Data Exchange (ETDEWEB)

Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

1997-11-25

Discussions were given on early degradation in up to about ten minutes in amorphous silicon solar cells. The experiment has used a model cell of single junction layer for power use with a Glass/ITO/P-i-n:a-Si/Al structure. Test samples were annealed at 130 degC for 30 minutes to eliminate hysteresis of degradation during storage. Xenon was used as an irradiation light source, and the temperatures were varied from 0 to 100 degC and the measurement time was set to 0.1 to 500 minutes. The result of the experiment may be summarized as follows: with regard to time-based degradation pattern for conversion efficiency, the tilt of a pattern to express degradation rate varies with temperature conditions, and changes in 10 to 20 minutes of light irradiation as a boundary; in long-term degradation after 20 minutes, the higher the environmental temperature, the lower the degradation is suppressed, but the rate of initial degradation up to about 10 minutes is higher as the higher the temperature; and the degradation rate increases as the higher the temperature in the initial degradation of about 10 minutes, whereas, corresponding to this fact, it is estimated that a phenomenon is involved, in which carrier recombination defect may increase. 4 refs., 7 figs., 1 tab.

Concentration characteristics and cell arrangement in luminescent concentrator PV modules; Keiko shukogata taiyo denchi module no cell haichi to shuko tokusei

Energy Technology Data Exchange (ETDEWEB)

Inamura, A [Science University of Tokyo, Tokyo (Japan); Sakuta, K [Electrotechnical Laboratory, Tsukuba (Japan)

1997-11-25

A luminescent concentrator PV module requires no tracking equipment and can use scattered light. A mini PV module was prepared from a luminescent plate of 100times100times3mm, and a single-crystalline PV cell of 100times20mm. Characteristics of various prototype modules with different PV cell areas and cell arrangements were also measured. Four kinds of edge reflecting materials with different reflectances by various white coating were applied to Al sashes for module frames, and each sash was fixed on one edge of the luminescent plate. In experiment, 3 other edges were covered with black tapes to reduce each reflectance to 0%. Although PV module output was affected by reflectance of edges, the output was satisfactory at 90% or more in reflectance showing no difference in output. A concentrating efficiency decreased with an increase in luminescent plate (concentrator) area, while it was improved by cell arrangement with short optical pass length, and cell arrangement hardly affected by edge reflection. 4 refs., 7 figs.

Improved design of three-dimensional lens for low concentrator PV modules; Teishukogata taiyo denchiyo sanjigen lens no koseinoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Goma, S; Yoshioka, K; Saito, T [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan)

1997-11-25

Attention is paid to reduction in area required for solar cells by solar concentration as a means of solving cost limits of solar cells and unstable supply of Si materials. Low concentration solar cells are effective from the aspects of utilization of scattered light and unnecessary ray tracing. The optical concentration ratio was calculated of three-dimensional lens having design values of various north/south and east/west direction allowable incidence half angles. The three-dimensional lens are designed by cutting a rectangular parallelepiped by the two-dimensional composite elliptical plane designed by various allowable incidence half angles from two directions of north/south and east/west. Using Perez`s sky solar radiation models and meteorological data HASP, calculated were the annual accumulated global radiation ratio on an inclined surface and the optical efficiency. Calculated were the solar cell area ratio and solar concentration area ratio of the concentration type to obtain solar radiation the same as that of the planar type. From the optimization calculation, it was found that lens are optimal which have design values of north/south and east/west direction allowable incidence half angles of 30-70deg. The solar cell area ratio is 57% and the solar concentration area ratio is 1.2 times. It was found that by making the module area 1.2 times, more than 40% of the solar cells used can be saved. 5 refs., 8 figs.

Analysis of output characteristics of PV modules under natural sunlight; Shizen taiyokoka ni okeru taiyo denchi module shutsuryoku tokusei no kaiseki

Energy Technology Data Exchange (ETDEWEB)

Murai, Y.; Igari, S. [Japan Quality Assurance of Organization, Tokyo (Japan)

1997-11-25

The paper measured current/voltage characteristics of various PV modules under natural light and analyzed various characteristics such as generated output and module power generation efficiency. In the experiment, installing various PV modules at the solar techno center located at north latitude 34.7deg and east longitude 137.6deg, measurement was made by I-V curve tracer, pyranometer, and thermocouple buried on the module back. As a result, the following were confirmed: As to the monthly mean power generation efficiency, the crystalline system is lowest in summer and highest in winter, and the amorphous system highest in summer and lowest in winter. Concerning the power generation efficiency and illuminance, the gap of power generation efficiency between at high illuminance and at low illuminance is large in the crystalline system and small in amorphous system. Relating to the azimuth angle of module installation and the generated output, the installation inclined 15deg angle west in summer and 15deg angle east in fall/winter generates more power in the crystalline system. On the contrary, the installation on the south face generates more power in the amorphous system. 4 refs., 8 figs., 3 tabs.

Effect of PV module output power on module temperature; Taiyo denchi no shutsuryoku henka ga module hyomen ondo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Hongo, T; Kitamura, A [Kansai Electric Power Co. Inc., Osaka (Japan); Igaki, K; Mizumoto, T [Kanden Kako Co. Inc., Osaka (Japan)

1996-10-27

Effect of the photovoltaic (PV) module output power variation on the module surface temperature has been investigated by field measurements. PV modules with capacity of 54 W were used for the temperature measurements. Three 2 kW-class PV systems were operated. T-type thermocouples were used for measuring temperatures. Measurement time intervals were 15 minutes, 30 minutes, 60 minutes, and 24 hours. Measurement period was between May 25, 1995 and June 25, 1996. The surface temperature increased during non-loaded PV output, and decreased during load-carrying PV output. Difference of the surface temperature between non-loaded PV output and load-carrying PV output was 3.5{degree}C at maximum through a year. The surface temperature was saturated within 30 minutes. When PV output was changed in 30 or 60 minutes interval, the variation of surface temperature was distinctly observed. When PV output was changed in 15 minutes interval, it was not observed distinctly. There was no difference of the surface temperatures during the time zones with less solar radiation, such as in the morning and evening, and at night. Except these time zones, difference of the surface temperatures was 3.5{degree}C at maximum. 4 figs.

Control method for light deterioration of amorphous solar cell. Temperature effect method; Amorphous taiyo denchi no hikari rekka yokuseiho. Ondo kokaho

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, H.; Yokoyama, S.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

1996-10-27

This paper describes a proposed method for suppressing light deterioration (temperature effect method), in which an annealing effect was always expected by laminating an NEM element and a heat insulation material on the back side of a-Si solar cell module and thereby raising the temperature in the back side of the module, and also describes an outdoor exposure test device completed for the method. The NEM element consisted of conductive potassium titanate and high molecular polymer and was a self temperature-controlling organic exothermic body that required no outside temperature control device. It was provided with a heat generating temperature of 45-75{degree}C as the exothermic property of the element and capable of generating heating temperature arbitrarily according to the purpose. The NEM element varied a resistance value against the ambient temperature and kept the element temperature constant. Measurement was commenced starting April 19, 1996, using the completed outdoor exposure test device and a measuring circuit. The deterioration phenomenon was and from then on continuously examined under the following conditions: (1) measurements were those of clear days only, and (2) measurements to be used were those between 10:00 and 14:00 with the quantity of solar radiation on a constant level. 4 refs., 4 figs., 1 tab.

Development of measurement device for evaluation of solar cell module output. 2; Taiyo denchi module shutsuryoku hyokayo sokuteiki no kaihatsu. 2

Energy Technology Data Exchange (ETDEWEB)

Minoda, M.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

1996-10-27

Enhancement in design efficiency may be attained as well as utilization in maintenance if on-the-spot data is made available, for the purpose of flexibly dealing with changes in design or matching with a house structure, in calculating the power generation output of a solar cell (PV) module. Under the circumstances, a small-sized compound measuring device was produced as a prototype which, using an I-V curve tracer, measured output and condition of a roof at the time of installation, compared with the optimum operation and predicted the power generation. The device was structured with the main body consisting of a computing part, measurement controller and power supply and with various sensor modules. The electron load control method was employed in order to measure I-V characteristics of the PV module, since it was desirable to use a variable load and to cover the range from the release voltage of a solar cell to the short-circuit state through the maximum output point. The reference module method was used for the system evaluation. The device was presumably applicable to a PV system design by incorporating a sensor module for measuring design environment data, which was essential at the time of a system design, in addition to those for measuring output. 9 refs., 4 figs., 3 tabs.

Measurement of friction coefficient for various thin films using millimeter-size movers driven by electro-static force. Seiden kudogata bisho mover wo mochiita usumaku no masatsu keisoku

Energy Technology Data Exchange (ETDEWEB)

Suzuki, M; Watanabe, S; Yoshimura, N [Akita Univ., Akita (Japan); Fujita, H [The University of Tokyo, Tokyo (Japan)

1992-12-20

Discussions were given on measurements of coefficients for static friction between different types of thin films. A small light-weight mover of a millimeter size was driven electrostatically to measure friction in a condition close to operation of a micromachine. The thin film materials were fabricated using a sol-gel process, sputtering, vacuum deposition and a CVD process. The materials include Ni, Ti, Al, SiO2, SiNx, Si wafers and glasses. The measured values for Ni-Ni, Al-Al and Ni-Al were larger by from 0.1 to 0.2 than values for bulk. The reason for this would be because of the friction generating mechanisms being different and the sample weight being lighter. Measured values for different types of thin films on silicon wafers were higher. This may be because OH groups are formed on the wafer surface causing high adhesiveness. Values for glasses are small in general. Friction coefficients for SiO2 thin films are small on the whole. However, SiO2-SiO2 showed larger values. This indicates that SiO2 is a useful material for micromechatronics, but proper selection of contacting opponents is important. 7 refs., 4 figs., 7 tabs.

Interim evaluation report on research and development of automatic sewing systems; Jido hosei system no kenkyu kaihatsu chukan hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The research and development project for automatic sewing systems is aimed at establishing the techniques necessary for developing (automatic sewing systems) which efficiently produce diversified types of products in small quantities, to cope with various requirements, e.g., diversified consumers' needs and reduced cycle periods. This project covers R and D of the sewing preparation/processing, sewing/assembling, cloth handling, and system management/control techniques. The program for developing the total systems and elementary techniques draws the conceptual designs of their functions, performance and shapes, to outline the overall R and D project. The programs for the individual elementary techniques include studies on their basic functions and performance; design works from the basic designs to determine the specifications to the detailed designs of the devices to be developed; construction of the test units on a trial basis; and function confirming tests to confirm operability of the unit components and device performance, where these works are simultaneously implemented. This paper describes the interim results of evaluation of the elements developed for the elementary techniques, summarizing the results obtained so far. It is concluded that most of the targets of the R and D themes are sufficiently achieved by the end of FY 1987, and that the project can be now advanced to the next phase, construction of the test plants. (NEDO)

Evaluation on the effect of tsunami and seaquake on the floating structure; Tsunami kaishin no futai ni taisuru eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K; Suzuki, H; Hosomi, I [The University of Tokyo, Tokyo (Japan); Nahata, H [The Long-Term Credit Bank of Japan, Ltd., Tokyo (Japan)

1997-12-31

The effects of tsunami and seaquake on large floating structures are theoretically studied, where these effects are followed in terms of local strength using the equation proposed by Sells to predict surface shapes changed by seaquake-caused uplift of the seabottom. The equation is combined with the one for tsunami propagation, to better predict the tsunami motion. The simulation results indicate the necessity of considering the effects of tsunami for the design of a large floating structure. The authors discuss that the effect of tsunami is minimized when a floating structure is set at a depth of at least 40 to 50m, chain length should be determined by equalizing the breaking weight with the load at which the structure starts to move, and a structure should be set at a position where it is not attacked by transverse waves. They also discuss that seaquake intensity should be predicted by the equation of motion of compressible fluid, and, noting local strength of a floating structure, it will not be damaged when it is at least 16mm thick under the conditions of 2m as seabottom uplift and 0.5m as draft depth. 15 refs., 9 figs., 2 tabs.

Report on evaluation/selection surveys on coal species, processes and others. Appendix; Tanshu process nado hyoka sentei chosa hokokusho. Furoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report, consisting of 7 chapters, summarizes literature related to liquefaction of coal. Chapter 1 describes the results of the (Project Lignite), i.e., development of the concept of two-stage liquefaction of lignite. Chapter 2 describes the COSTEAM process, which uses synthesis gas (CO-H{sub 2}) as the reducing agent and coal moisture as the hydrogen source for liquefaction of coal of low degree of carbonization, e.g., brown coal. Chapter 3 describes solubilization of coal with alcohol, where coal is reacted with ethanol and NaOH at 300 to 420 degrees C. Chapter 4 describes liquefaction of coal and production of lighter products with tetrahydroquinoline as the hydrogen donor. Chapter 5 describes low-temperature carbonization as the process for liquefying coal, in particular brown coal. Chapter 6 describes possibility of development of new liquefaction techniques for brown coal, including solvolysis for liquefaction, role, recovery and reuse of catalysts, short contact time processes, and coal pretreatment. Chapter 7 describes economic viability of the secondary hydrogenation. (NEDO)

Characteristic on photovoltaic/thermal hybrid collector. Evaluation of excergetic theory; Taiyoko netsu hybrid collector no tokusei. Exergy ni yoru hyoka

Energy Technology Data Exchange (ETDEWEB)

Iwawaki, H; Morita, Y; Fujisawa, T; Tani, T [Science University of Tokyo, Tokyo (Japan)

1997-11-25

Described herein are characteristics of photovoltaic (PV)/thermal hybrid collectors (PV/Ts), in which a PV module is combined with a plate-shape solar heat collector to simultaneously produce electric power and heat. Their efficiency is assessed by exergy. The test results indicate that the PV/T system gives a 1.07 times higher exergy than the PV system, 86.3 versus 80.7kWh. In terms of energy, the optimum values (OVs) are 5, 44 and 37% lower than the measuring values (MVs) for electrical energy, thermal energy and total exergy. In terms of exergy, on the other hand, OV is 5% lower than MV for electrical energy, but 893 times higher for thermal energy and 1.26 times higher for total exergy. As a result, the exergy level is 26% higher than that of a system which generates power as the main product and heat as the auxiliary product. 3 refs., 6 figs., 5 tabs.

Accuracy of parameters of permeable fractures by hydrophone VSP; Hydrophone VSP ni yoru tosuisei kiretsu no tokusei hyoka no seido

Energy Technology Data Exchange (ETDEWEB)

Kiguchi, T; Ito, H; Kuwahara, Y; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Yabuuchi, S; Hasegawa, K [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

1997-10-22

Hydrophone VSP (vertical seismic profiling) experiment is under way as a technique for detecting subsurface water-permeable cracks by use of boreholes and for evaluating their characteristics (permeability index, crack direction, dip angle). In this report, tube waves observed by hydrophone VSP are subjected to analysis for the determination of water-permeable crack characteristics, the impact caused by errors in the value inputted for analysis is estimated, and a model calculation is performed in case there is no agreement between data from the borehole and data from VSP, all for examining the VSP records for accuracy. When an error rate of 15% is given to the tube wave/P-wave amplitude ratio, a change of 40% or lower results in the permeability index, and a change of 10deg or less in the dip angle, which means that an error in the amplitude ratio does not affect the analysis very much. Changes in the amplitude ratio resulting from changes in crack direction and dip angle differ, dependent on the offset rate. When angular differences among plural crack directions are within 90deg and dip angles within 60deg, the result of analysis represents the average characteristics of the plural cracks. 7 refs., 5 figs., 2 tabs.

How to examine flaking sex evaluation of the float bus bottom brick; Furotobasubotomu renga no furekingu sei hyoka shiken hoho

Energy Technology Data Exchange (ETDEWEB)

Yoneyama, R. [Yotai Refractories Corp., Osaka (Japan)

1999-02-01

After it was used in the float law glass dissolution drawer fireplace bottom, a countermeasure was established by answer, laboratory simulation and high temperature load deformation investigation that that cause was in performance about incumbent elephant of the bottom department clay brick which becomes clear from the second. Though it accompanies melting metal tin and Na that it got into the inside of the brick is a cause as for formation, is expected future development by the high research of the practical use which effective measure was taken against by the organization of the clay brick and the improvement of the physical nature. (translated by NEDO)

Framework of information system assessment based on function and quality; Kino to hinshitsu ni motozuku joho system hyoka no wakugumi

Energy Technology Data Exchange (ETDEWEB)

Takahashi, M.; Hishitani, J. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-03-01

As for function and quality of information system, an assessment method of productivity at planning and at completion has been developed. In this method, functional size expressing the size of functional kinds provided by the system, value-added size expressing the size with corrected functional size in response to the quality level of each function, and production size expressing the size of products and processes under the given conditions were employed as indexes for evaluating the size of system. In addition, a method using the quality property tree has been developed. In this method, to evaluate the quality level which is essential for calculating the value-added size, users and providers evaluate the system quality from their own viewpoints. By this system, validity of user`s demand and validity/efficiency of realizing process can be evaluated for client/server type systems from the systematic viewpoint in a whole life cycle of systems from development planning to abandonment of systems. 24 refs., 5 figs., 3 tabs.

Evaluation on the effect of tsunami and seaquake on the floating structure; Tsunami kaishin no futai ni taisuru eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K.; Suzuki, H.; Hosomi, I. [The University of Tokyo, Tokyo (Japan); Nahata, H. [The Long-Term Credit Bank of Japan, Ltd., Tokyo (Japan)

1996-12-31

The effects of tsunami and seaquake on large floating structures are theoretically studied, where these effects are followed in terms of local strength using the equation proposed by Sells to predict surface shapes changed by seaquake-caused uplift of the seabottom. The equation is combined with the one for tsunami propagation, to better predict the tsunami motion. The simulation results indicate the necessity of considering the effects of tsunami for the design of a large floating structure. The authors discuss that the effect of tsunami is minimized when a floating structure is set at a depth of at least 40 to 50m, chain length should be determined by equalizing the breaking weight with the load at which the structure starts to move, and a structure should be set at a position where it is not attacked by transverse waves. They also discuss that seaquake intensity should be predicted by the equation of motion of compressible fluid, and, noting local strength of a floating structure, it will not be damaged when it is at least 16mm thick under the conditions of 2m as seabottom uplift and 0.5m as draft depth. 15 refs., 9 figs., 2 tabs.

Production of ethanol, fat and oil and methane gas from several crops. Sushu sakumotsu nado no energygen toshite no hyoka

Energy Technology Data Exchange (ETDEWEB)

Uehara, Tsuyoshi; Suganuma, Hirotoshi

1988-05-01

Aiming at production of ethanol, fat and oil and so on, ten kinds of miscellaneous cereal crops such as pearl-millet, soybean and so on were grown, and comparative investigation of the production rate which was considered utilization of whole plants were carried out. The suitability of vegetable wastes as methane fermentation materials for the methane gas production was investigated by the constituent analyses and methane fermentation experiments. Nine kinds of the grasses and vegetable wastes such as tomatoe buds, broccoli leaves were used for the investigation. As the results, the estimated yield of ethanol per 10 are from pearl-millet was 690 liter, the estimated yield of fat and oil per 10 are was 70 liter from soybean, The results of the analyses of nine kinds of the farm residues were as follows: (1) carbon content of about 40 %, (2) C/N ratio of 13 av., (3) C/P ratio of 91 av., and (4) the content of C,N and P was roughly appropriate. 680 to 760 milliliter of methane gas was produced from one gram of the dry matter of tomatoe bods, and in case of broccoli leaves, 424 milliliter of methane gas was produced, it was found that these values were not inferior to animal dung. (4 figs, 15 tabs, 6 refs)

Study on visibility evaluation model which is considered field factors; Field factor wo koryoshita shininsei hyoka model ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakanishi, M; Hagiwara, T [Hokkaido University, Sapporo (Japan)

1997-10-01

The present study proposes a model to evaluate visual performance of road traffic facilities required for drivers. Two factors were employed to obtain the suitable contrast for drivers under driving situation. One factor is a suitable luminance range, which is derived from minimum required luminance and glare luminance. Another is a field. The model showed capability of providing visibility range in some cases. 8 refs., 4 figs., 2 tabs.

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of manufacturing technologies for low-cost substrates (technical development for production of high purity silicon); Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Tei cost kiban seizo gijutsu kaihatsu (taiyo denchiyo silicon seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of manufacturing technologies of Si for solar cells in fiscal 1994. (1) P in Si could be successfully reduced to 0.1ppmw by EB melting method. The condition possible to reduce P in Si while continuously supplying metal Si was found. The 20kg class EB melting equipment was also designed and manufactured which can be connected with solidifying rough refining process. (2) Use of a water-cooling copper mold was studied using a small melting equipment for cost reduction in solidifying rough refining process. As a result, the prospect of crucible-free technology for removal of P and solidifying rough refining was obtained. (3) B in Si could be successfully reduced to the target of 0.1ppmw by vapor addition method using a plasma melting equipment. (4) The prototype SOG-Si achieved a conversion efficiency of 14.1% as solar cell. In addition, the advanced solar cell prepared by efficiency enhancement process achieved a conversion efficiency of 15.9%. 3 figs.

Photocatalytic removal of nitrogen oxides from ambient air using solar energy; Taiyo energy wo riyoshita taikichu no NOx no hikari shokubai jokyo

Energy Technology Data Exchange (ETDEWEB)

Fukaya, M; Taoda, H; Watanabe, E; Nonami, T; Iseda, K; Kato, K [National Industrial Research Institute of Nagoya, Nagoya (Japan); Kunieda, S [NGK Insulators, Ltd., Nagoya (Japan); Kato, S

1997-11-25

Experiment was made on removal of NOx from ambient air using ceramic blocks coated with a newly developed easy-to- handle TiO2 film photocatalyst. After TiO2 sol was prepared by hydrolyzing titanium tetraisopropoxide, the photocatalytic blocks were prepared through drying and sintering after immersing the blocks in TiO2 sol. The effect of the number of coating on catalytic performance was studied using the single-coated and triple-coated blocks. Artificial solar light of 1mW/cm{sup 2} was used as light source for flowing reaction experiment of air (containing NOx) in a laboratory. NOx concentration rapidly decreased with irradiation, and 94% and 98% of NOx were removed by the single- and triple-coated blocks, respectively. NOx was completely oxidized to HNO3 through NO2 by triple-coated blocks. The demonstration test of removal of NOx from ambient air in Okazaki city showed a removal rate of nearly 90% in noonday and 40% or more in average, while not 0% but 5-20% even in the nighttime. The latter is probably derived from adsorption by the porous photocatalytic blocks. 2 figs., 4 tabs.

Analysis and evaluation of data to accompany the development of geothermal water use power plant, etc. Analysis and evaluation of polymeric materials exposed to geothermal heat at depths; Nessui riyo hatsuden plant nado kaiahtsu ni tomonau data no kaiseki hyoka. Shinbu chinetsuyo kobunshi zairyo no kaiseki hyoka

Energy Technology Data Exchange (ETDEWEB)

Kenmochi, K.; Takahashi, J.; Takayanagi, H.; Tsuda, H.; Nagai, H.; Takeuchi, K. [Agency of Industrial Science and Technology, Tokyo (Japan); Nagasawa, C. [Kumamoto Prefectural Industrial Technology Center, Kumamoto (Japan); Hamada, T. [Science University of Tokyo, Tokyo (Japan). Faculty of Industrial Science and Technology

1998-11-20

Remaining life assessment technologies for polymeric materials for geothermal power generation and methods for improving their heat resistance are reviewed, and concepts of scale-free technologies for FRP (fiber-reinforced plastic)-sandwiched pipelines for hot water transportation are described. Materials based on PTFE (polytetrafluoroethylene) and NBR (acrylonitrile-butadiene rubber) are chosen for use as DHM (down-hole motor) sealing material and for application to the stator. With PTFE as the matrix, four candidates are prepared, which are additive-free PTFE, and GF/PTFE, GF/CF/PTFE, CF/PTFE, each containing 20w% GF (glass fiber) and/or 20w% CF (carbon fiber). With NBR serving as the matrix, two candidates are prepared, which are NBR-A containing 20w% aramid fiber and NBR-W which is a vulcanized NBR-A. External force, heat, light, and mud are named as the degradation factors, and each factor and some combinations of external force, heat, and light are repeatedly imposed on the materials. During the effort to develop an apparatus for simulating geothermal circumstances in which the factors will affect the materials in complicated ways, a life assessment technique is developed for such polymeric materials. A technology is developed for providing polymeric rubber elastomer with a heat resistant feature. A study is made to replace transportation pipelines for injection wells with FRP sandwiched pipelines. (NEDO)

Quantitative evaluation of ground improvement by chemical grouting using electrical resistivity. Part 3. Applicability of evaluation of improved region by resistivity tomography; Denki hiteiko ni yoru yakueki chunyu kairyo koka no teiryoteki hyoka hoho. 3. Hiteiko tomography wo riyoshita jiban kairyo han`i hyoka hoho no tekiyosei

Energy Technology Data Exchange (ETDEWEB)

Komine, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-02-01

This paper describes a method for evaluating grouting that is a means for improving the ground for excavation for building underground structures in urban areas. This is an effort for improving reliability, and evaluates the rate of filling of the water glass base chemical liquid injected for improving the ground utilizing the fact that this liquid is higher in conductivity than the soil or ground water. An experiment was conducted using a model ground so as to define the limit of applicability of this resistivity tomography by studying electrode arrangements and difference in resistivity between the grouted liquid and ground water. It was then found that the liquid-injected region is evaluated more accurately when the measuring electrodes are installed nearer to the region, that evaluation is satisfactorily accomplished when the region spans not less than 75% of the distance between the electrodes, that higher accuracy is expected when the difference in resistivity is greater between the grouted liquid and ground water, that evaluation is satisfactorily accomplished when the resistivity of the grouted liquid is not more than 10% of that of ground water, and that any grouting liquid usable for ground improvement in civil engineering in urban areas can be applied to any other grounds except where there is influence of seawater. 31 refs., 55 figs., 8 tabs.

Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

Report on a survey in fiscal 1999. Survey on energy use evaluation systems; 1999 nendo energy shiyo hyoka system chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The present survey and study relate to the medium to long term policies for technological development of energy and environment related technologies, and are intended to develop a system that can evaluate the importance, feasibility, expected realization time, and expected cost of the technologies, including their synergetic effects. The survey and study are intended to provide clear guidelines for planning the technological development policies on which of the technological development should be promoted in what ways, based on the evaluation given by the use of the system. The report describes in Section 1 to adopt two types of approaches of a 'technology map' and a 'network chart evaluation system' to achieve the goal. Section 2, after describing the results of surveys on the past study cases of technology evaluation, describes that the present approach has new features that are different from conventional ones. Section 3 states the results of surveys on the basic technologies to prevent global warming, and shows cases of preparing maps that notice on energy flows. Section 4 relates to network chart evaluating methods. Section 5 describes the results of surveys that have been made in relation with chronological progress of the technological development, in preparation for surveys to be made in the coming fiscal years. (NEDO)

Fiscal 1998 research report on development, study and evaluation of tribo-materials; 1998 nendo tribo material no kaihatsu chosa hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Recently, needs for tribo-materials are on the increase for further energy saving and improvement of various functions and durability in various field such as less-fuel consumption car, new type Shinkansen, linear motor car, high-speed motor boat, various machines and tools, electronics, medical equipment and vitally adaptable material. This project researches and studies various properties required for tribo- materials for surface treated materials by ceramic and other material films, and clarifies the guidance and direction of the technology for creating tribo-materials by surface treatment and surface modification, through clarifying a friction/abrasion mechanism by collection of basic characteristic data and analysis of abrasion powders. This project is studying the marginal condition of film destruction for ceramic system vapor-phase deposited films, through studying the effect of mechanical properties of substrates, film surface treatment methods and film surface shapes on the marginal condition. (NEDO)

Method of estimating time management of safety control of combustion. Nensho anzen seigyo no tame no jikan kanri No hyoka hoho

Energy Technology Data Exchange (ETDEWEB)

Moroboshi, M. (Yamatake-Honeywell Co. Ltd., Tokyo (Japan))

1993-12-01

The results of investigating time management (permissible value of ignition time and prepurge time) for safety control of combustion relating to a combustor is reported. It is shown that the heating value of hydrocarbon-based fuel is determined by molecular weight irrespective of molecular structure and constant (11200kcal/kg) per unit weight; the heating value of mixture gas of theoretical mixture ratio is constant (1000kcal/m[sup 3]) indifferently of the kind of fuel; and that the product of the heating value of a fuel and the lower limit of its explosion limit is approximately constant (400-600kcal/m[sup 3]). Succeedingly it is shown based on these values that allowable ignition time is determined by the combustion chamber load (ratio of the maximum amount, 10[sup 4]kcal/h, of combustion to the volume of combustion chamber); the effect of dilution by exhaust lengthens it by only about 50%; and that the conventional criterion that the frequency of ventilation of prepurge should be 4-5 or that the minimum time of prepurge should be 30 seconds is appropriate. 6 refs., 4 figs., 1 tab.

Evaluation on reliability and safety of marine diesel engine and mechatronics. Hakuyo diesel kikan to mechatronics no shinraiseiter dot anzensei hyoka

Energy Technology Data Exchange (ETDEWEB)

Kido, H. (Kaigi Univ., Kobe (Japan)); Hashimoto, T. (Kobe Univ. of Mercantile Marine, Kobe (Japan))

1992-06-01

Reliability and safety are evaluated for main diesel engines, generator diesl engines, their mechatronics and auxiliary machines on ships. The evaluation is based no statistical analysis of field data collected from outland navigation by MO diesel engine the period of 1983-1988. Evaluation indexes are used for analysis, such as failure rate (total number of failure/total navigation hour), mean maintenance man power: mh (total maintenance man power for determined period/total number of failure), manning index: MI (maintenance manpower for repairing failure occurred during 1000 hour navigation). With respect of total failure of ship plant as a whole, the failure rate decreased from 13.2 to 7.4, namely almost to half and mh was tending to increase from 5.5 to 5.8, while MI decreased from 73.0 to 43.1. With respect to heavy failure which is regarded as a scale of safety, the failure rate remained within a range of 0.7-0.5 and mh showed down-up movement like 30{yields}10.4{yields}18.8, while MI moved like 18.6{yields}5{yields} 10.9 . 3 refs., 9 figs., 3 tabs.

Hydrogen cracking susceptibility evaluation of buried steel pipe under cathodic protection. Cathode boshokuka ni okeru maisetsu kokan no suisoware kanjusei hyoka

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, Y.; Nonaka, H. (Osaka Gas Co. Ltd., Osaka (Japan)); Yamakawa, K. (University of Osaka Prefecture, Osaka (Japan). College of Engineering)

1992-12-01

An evaluation was given on effects of hydrogen on pipeline materials in order to determine a most base value in an optimal cathodic protection potential in cathodic protection of buried pipelines. Protection potentials were estimated from the relation between critical hydrogen amount and the potentials in marine clays and sodium acetate as electrolyte. The materials were evaluated using a strain rate tensile experiment method. The following results were obtained: The more base the potential, the elongation was somewhat less than the result in air, while the tensile strength increased slightly; difference in water content in soils varies the cross section contraction rate; the rate does not change in a marine clay containing water at 20%, but it decreases in a 30%-content soil; an SEM observation revealed pseudo cleavage faces; and the critical hydrogen amount that causes hydrogen cracking is 10 ppb, which corresponds to -1.4V in a marine clay containing water at 30%, and -1.2V at 14%. A loading experiment with actual loads verified that no fracture due to hydrogen cracking occurs even under an overprotection environment when a load imposed on an actual pipeline is kept constant. 16 refs., 10 figs., 3 tabs.

Evaluation of the performance in the solar assisted heat pump system; Taiyonetsu riyo heat pump system no seino hyoka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Saito, Y [Osaka Institute of Technology, Osaka (Japan)

1996-10-27

Performance of a solar heating system with a hydrothermal source heat pump was evaluated and compared with that of a direct solar heating system. The sun-dependency rates ({Sigma}D and {Sigma}H)of the direct system and heat pump (HP)-provided system were expressed as a function of the rate ({alpha}) of the auxiliary heat against the collected heat and as a function of the performance coefficient and {alpha}, respectively. When the sun-dependency rates are compared, it is found that the HP-provided system is the more advantageous when {Sigma}H/{Sigma}D>1. The relationship between the {alpha}`s of the two systems was clarified and computation was performed to compare the sun-dependency rates on condition that the two are equal in the heat collecting area. Although the sun-dependence rate cannot be elevated to 100% in the HP-provided system, it achieves a sun-dependency rate higher than that of the direct system even when the heat collecting area is small. In cases where the building is economically limited, for instance, with respect to the area for solar collector installation, it is advantageous to employ the HP-provided system. 5 figs., 1 tab.

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of amorphous silicon-based high-quality material/substrate manufacturing technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu - amorphous silicon kei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to enhance the stability of amorphous solar cells. For elevating TCO (transparent conductive oxide) substrate transmittance to an ultrahigh level and for obtaining amorphous layers less to suffer photodegradation, efforts were made to develop substrate materials stable upon exposure to plasma and low in defect density. In the study of TCO, a high-transmittance glass substrate was employed and TCO was made thinner, and the specimen achieved transmittance of 91.3% or 6.3% over that of the conventional type. In the study of low reflection films, it was found that their transmittance came to be stable and remain so after 150 days after a weatherproof test. In the study for stability enhancement, optimization was carried out for a plasma resisting Ga{sub 2}O{sub 3}-added ZnO film for the manufacture of a substrate material capable of properly behaving in a high-speed a-Si film fabrication process. Low-temperature film fabrication was studied to enable low-cost manufacturing, and it was learned that a 4 times 10{sup -4} ohm/cm low-resistance film was obtained by sputtering Ga{sub 2}O{sub 3}-added ZnO where magnetism was intensive at room temperature, that films excellent in crystallinity were obtained by the same method even at low temperatures, and so forth. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program survey and research. Joint projects on solar energy between Japan and Australia, etc. (Joint efforts for high-grade flat-plate collector development); 1981 nendo Nichigonado taiyo energy gijutsu kyoryoku jigyo seika hokokusho. Nichigo taiyo energy gijutsu kyoryoku (kokyu heiban collector kaihatsu kyoryoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Investigated at DET (Division of Energy Technology) are a unit for controlling air convection in between a heat collector heat-collecting plate and the cover, testing methods, and under-floor heat accumulation using a horizontal rock bed. DMC (Division of Mineral Chemistry) is engaged in the study of black Ni selective absorption film formation on a metal plate and a reflection-preventing film for a heat collector. Monash University studies methods for testing heat collectors, transfer of heat, heat pipe, tracking mechanism, etc. Melbourne University is dedicated to computer model calculation involving solar energy utilization. Sydney University deals with collectors, selective absorption films, absorption type refrigerators, heat accumulation, and desalination of water. Under study at New South Wales University are passive solar systems, photothermal collectors, solar cells, etc. The Beaseley Corporation is a manufacturer of heater collectors and water heaters in South Australia, and a visit is paid to the corporation for the study of its manufacturing process. The Rheem Corporation manufactures water heaters in New South Wales, and its presence in the solar collector industry is known. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of amorphous solar cells (Research and development of amorphous solar cells on flexible film substrates); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Kadosei film wo kiban to suru amorphous taiyo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-31

Efforts will be made to reduce the cost, increase efficiency, and enlarge cell areas and, at the same time, to establish the foundation of a roll-up type solar cell manufacturing process which is required for the implementation of mass production. In an inverted pin/ITO (indium-tin oxide) hetero-face structure cell installed on a polymer film substrate, a conversion efficiency of 5.33% is achieved in the case of a solar cell whose n-layer is of the amorphous phase, and 6.36% in the case of a cell of the microcrystallized phase. A roll-up type glow discharge CVD (chemical vapor deposition) unit is designed and experimentally built, which is for the realization of large area cells. It is now duly expected that an undoped (i-type) a-Si:H film will be deposited to a thickness of approximately 5000A. As the result of a first-step screening conducted in search of amorphous solar cell sealing materials, some applicable plastic materials are selected. The future is bright of amorphous solar cells on polymer film substrates. (NEDO)

Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (solar furnace); 1974 nendo taiyo energy riyo system chosa kenkyu. Taiyoro

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

In fiscal 1974, analysis was made on the concept design of solar furnace hardware, and utilization and use purpose of solar furnaces as high-temperature industrial heat source. Detailed survey was also made on the history of high- temperature solar furnaces. Based on the history of large- scale solar furnaces and the current state of some industries consuming a large amount of thermal energy, wide consideration was made on the applicability of large-scale solar furnaces as heat source in the future. Although various applications of large-scale solar furnaces are expected in the future, their current main applications are production of high-melting point materials, research on high-temperature physical properties, production of silicon, and solar heat power generation. A solar furnace is mainly composed of a parabolic reflector and heliostat plane reflector as optical system. It is necessary for practical industrial use of solar furnaces to study on furnace core design, profitability, installation site, temperature control, and reflector maintenance enough. (NEDO)

Control method for light deterioration of amorphous solar cell. 2. Temperature effect method; Amorphous taiyo denchi no hikari rekka yokuseiho. 2. Ondo kokaho

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, H; Itsumi, J; Sano, N [Kumamoto Institute of Technology, Kumamoto (Japan)

1997-11-25

Experimental studies have been carried out on suppressing early deterioration in amorphous silicon solar cells. The amorphous silicon solar cell is characterized by deterioration due to light irradiation and restoration due to temperature rise. An exposure experiment was performed under three conditions: installation in natural environment, installation with rear side of the solar cells covered with an insulating material, and installation with rear side of the solar cells covered with warming elements and an insulating material. Tests were made on suppressing progress of the early deterioration caused by temperature conditions. As a result, the efficiency in the natural condition was found to decrease as largely as 32% in an open circuit condition and 58% in a short circuit condition. The efficiency reduction rate was smaller in the open circuit condition when the insulation material was installed, but in the short circuit condition, resistance characteristics caused by rain water and electrolytic corrosion were exhibited. For the case with warming elements installed, the reduction in the efficiency was more remarkable, contrary to the expectation. The cause was determined that water existing between the rear side and the warming elements was warmed up, accelerating the electrolytic action, and resulting in deterioration advanced over a wide area in the rear side. 6 refs., 6 figs., 3 tabs.

Development of a high temperature solar receiver for high-efficient thermionic conversion systems; Fukugo netsuden henkan system yo chokoon taiyo junetsuki no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Umeoka, T; Naito, H; Yugami, H; Arashi, H [Tohoku University, Sendai (Japan). Faculty of Engineering

1996-10-27

For thermionic conversion systems (TIC) using concentrated sunlight as heat source, the newly developed solar receiver was tested. Concentrated sunlight aims at the inner surface of the cavity type solar receiver. The emitter of TIC installed in the rear of the solar receiver is uniformly heated over 1700K by thermal radiation from the rear of the solar receiver, emitting thermion. Electric power is generated by collecting the thermion by collector. Mo is used as emitter material, however, because of poor heat absorption of Mo, high-absorptive TiC is used for heat absorption surface to heat Mo by thermal conduction from high-temperature TiC. Functionally gradient material (FGM) with an intermediate layer of gradient TiC/Mo ratios between TiC and Mo is used as emitter material. The emitter is thus uniformly heated at high temperatures of 1723{plus_minus}12K. As a result, the developed solar receiver is applicable to heat the emitter of TIC. Heat flux measurement at the graphite cavity clarified that cavity temperature of as high as 1780K and heat flow of 50W/cm{sup 2} are obtained at 4.7kW in input. 6 figs.

Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation of peripheral technology for photovoltaic power system (analysis and evaluation on photovoltaic systems); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Shuhen gijutsu kaihatsu no tame no kaiseki hyoka (taiyoko hatsuden system shingata chikudenchi)

Energy Technology Data Exchange (ETDEWEB)

Kurokawa, K; Endo, E; Tsuda, I; Nakamura, K; Sugiyama, Y; Nakazawa, S; Takaku, K; Yanagisawa, T; Kojima, T; Shimizu, K; Koyanagi, T; Onda, N; Nozaki, K; Negishi, A; Kaneko, Y [Electrotechnical Laboratory, Tsukuba (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for analysis and evaluation of new storage batteries for photovoltaic power systems. Quantitative analysis and evaluation are made for introduction of intermittent operational mode in the conventional power supply system in which electrolyte units are connected in parallel and for improved performance by bubbles flowing into the line that supplies the electrolyte to the stack, in order to establish the configurations of and operational procedures for the redox flow batteries. The study on development of redox battery compares the Pb-Sn alloy felt collector with carbon fiber, Pb-Sb alloy felt and the lattice for the conventional lead acid battery, in order to optimize the new lead felt battery. As a result, it is found that the Pb-Sn alloy felt collector is better than any other device tested, because of its higher freedom with respect to electrode shape and battery size. The study on reliability evaluation of amorphous solar cells tests photoelectric conversion efficiency of a-Si solar cells, in order to elucidate the phenomena where degradation and rejuvenation compete with each other under weak light irradiation conditions. 8 figs., 1 tab.

Performance evaluation of solar heating system with thermal core type soil heat storage. Part 5. Performance prediction and evaluation of the system considered of the weather condition; Taiyonetsu riyo netsu kakushiki dojo chikunetsu system no seino hyoka. 5. Kisho joken wo koryoshita system no seino yosoku to hyoka

Energy Technology Data Exchange (ETDEWEB)

Yoshida, N [Nishimatsu Construction Co. Ltd., Tokyo (Japan); Nakajima, Y [Kogakuin University, Tokyo (Japan)

1997-11-25

The paper studied a solar heating system with thermal core type soil heat storage (combining a thermal core composing of a water tank and an underground pebble tank and the soil around the heat storage tank and also using solar energy). Solar energy is stored by temperature level in the high temperature water tank, the low temperature pebble heat storage tank and the soil around the heat storage tank. Heat is recovered according to temperature as direct ventilation space heating (utilization of pebble tank air), floor heating (utilization of hot water of the heat storage water tank) and heat pump heat source (utilization of pebble tank air). A study was made of performance and regional effectiveness of the system under different weather conditions. A study was also made of effects of the water tank for short term heat storage by changing the water volume. Using the same structure, etc. for the system, the system was evaluated using weather data of Sapporo, Tokyo and Kagoshima. In terms of efficiency of the system, the system structure was found to be most suitable for weather conditions in Tokyo. However, the air heat source heat pump which cannot be usually used in the cold area has come to be used. Such effect except efficiency is also considered, and the amount of performance to be targeted in each region changes. 2 refs., 14 figs., 1 tab.

Evaluation of water content in rock mass by electromagnetic and resistivity tomography. Denjiha, hiteiko tomography ni yoru ganban no gansui jotai hyoka

Energy Technology Data Exchange (ETDEWEB)

Inaba, T; Inoue, M; Matsumoto, K [Kajima Corp., Tokyo (Japan)

1993-10-31

As a method to evaluate the rock mass, electromagnetic tomography and resistivity tomography were tested on the original site. The electromagnetic tomography can tomographically analyze the propagation velocity and initial amplitude damping. The resistivity tomography uses a finite element method from the initial resistivity distribution model and finally gives a model which is nearly equal to the actual resistivity distribution. Both the above tomographic analyses can detect the crushed spot as a low velocity, high damping and low resistivity spot. However, the electromagnetic tomography could detect finer structure than the resistivity tomography. The water content of rock mass was evaluated from the damping coefficient which was given by the amplitude damping tomography of electromagnetic wave. If it is compared with the water content which is given by the dielectric constant of velocity tomography, there partially exists discrepancy between both, because the damping coefficient contains information on cracks which disperse and reflect the electromagnetic wave. Between the resistivity and porosity, there exists a known experimental formula, which was satisfied by the presently given resistivity. 9 refs., 10 figs.

Fiscal 1997 report on the introductory study. Human behavior recognition evaluation technology; 1997 nendo sentan kenkyu hokokusho. Ningen kodo ninchi hyoka gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Importance of the human behavior technology was paid attention to to get true safety and comfortableness of life through adaptability of products/systems to all humans. In consideration of the social and technological background, the human behavior recognition evaluation technology avoids economic/social losses caused by accidents and troubles and also provides the safe life environment for living people including the aged. Further, the gist of the project was proposed to make it clear that it can give a course of making things from a viewpoint of development of products dealing with individuals (personal fit) and can give new added values and contribute to heightening of international competitiveness at the same time. Development is made of technology of dividing concrete behavior patterns into types and also accumulating them in usable forms at the time of product design and in emergency and of technology of measuring all the time information on human behaviors in daily life without restrictions and on site. Supporting technology is developed for making the most of behavior information of users for product design and in emergency. Effects of the spread are also estimated. 76 refs., 13 figs., 9 tabs.

Environmental assessment of surfactant using aquatic microcosm system; Konuma no suiken seitaikei ni oyobosu kaimen kasseizai no microcosm system wo mochiita hyoka

Energy Technology Data Exchange (ETDEWEB)

Takamatsu, Y.; Matsumura, M. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering

1995-10-10

Microcosm system was applied to assess effect of surfactants on aquatic ecosystem. Surfactants such as LAS and Soap were added to an aquatic flask-size microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer. In the system, NOEC (no observed effect concentration) of LAS was below 1.5mg{center_dot}l{sup -1}, whereas soap was below 30mg{center_dot}l{sup -1}. Microcosm test is a pertinent tool to assess the effect of surfactant on ecosystem because microcosm test makes it possible to evaluate the effect of surfactant from a viewpoint of the interaction of microorganisms, material cycle and energy flow. With these respects, microcosm test is useful environmental assessment method which can reflect aquatic ecosystem. 10 refs., 6 figs., 1 tab.

Economic evaluation on participation of IPP as seen from an electric power system; Denryoku system kara mita IPP sannyu no keizaiteki hyoka

Energy Technology Data Exchange (ETDEWEB)

Kato, F.; Horibe, H.; Hayakawa, M.; Suzuki, Y.; Kaji, Y. [Nagoya University, Nagoya (Japan)

1997-01-30

A discussion was given on value of participation of an IPP as seen from an electric power system operation plan prepared by utilities. In the discussion, evaluation was made using as the breakeven cost of IPP power purchase prices the difference in power generation cost between electric power systems in which an IPP is participating and not participating, or in other words, the reduced portion of the power generation cost. As a result of the discussion, the following matters were indicated: in the case where an utility company expands its capacity by installing a coal-fired thermal power plant which is lower in operation cost, to deal with increase in power demand, the breakeven cost could be an avoidable cost for the utility company; if the expansion by installing a coal-fired thermal plant is not possible, the breakeven cost for a base type IPP would rise; the breakeven cost for a peak type IPP would be higher than for the base type IPP because the breakeven cost can serve to cut the peak for generators owned by the utility company; and participation of an IPP to power sources in remote areas would provide a large effect to reduce power transmission loss in an entire system, thereby increasing the breakeven cost. 1 ref., 9 figs., 3 tabs.

Method for evaluating environmental performance of technologies by using the interindustry relations table; Sangyo renkanhyo wo mochiita gijutsu no kankyosei hyoka shuho

Energy Technology Data Exchange (ETDEWEB)

Hondo, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-01-30

This paper describes a proposal of a method for evaluating environmental performance of technologies by using the interindustry relations table, and the case studies thereof. This method is characterized in that it can evaluate two effects affecting the environment: structuring of capital facilities required in association with introduction of the technologies and the changes in social structures. As a parameter to compare the technologies considering these effects, a concept of life cycle limited emission amount was introduced. In the case studies, life cycle limited CO2 emission amounts from using seven kinds of technologies were calculated, and environmental performances of each technology were compared. The result indicated that introduction in Japan of coal, oil and LNG fired thermal power generation will increase CO2 emission amount from the whole society. Conversely, introduction of hydraulic, nuclear, photovoltaic, and wind power generation technologies will reduce the CO2 emission amount. It is pointed out particularly that hydraulic and nuclear power generation can minimize CO2 emission from structuring capital facilities, and is an excellent technology from a viewpoint of reducing CO2 emission from the society as a whole. 5 refs., 6 figs., 1 tab.

Examination of optimal data acquisition for evaluation of PV systems; Taiyoko hatsuden system hyoka no tame no saiteki keisoku shuho no kento

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, H; Kurokawa, K [Tokyo University of Agriculture and Technology, Tokyo (Japan); Otani, K; Tsuda, I [Electrotechnical Laboratory, Tsukuba (Japan)

1996-10-27

A 70 kW-class photovoltaic (PV) power generation system of the Tsukuba Research Cooperation Center, Agency of Industrial Science and Technology was evaluated using hourly measurement data. Hourly solar irradiation, mean PV module temperature, hourly array generated power, hourly PV system generated power were selected as the measurement items, to examine the validity of measurement method. Furthermore, based on these measurement data, the loss factors were estimated, which reduce the system efficiency. They included the losses due to the shadow effect, the deterioration of module efficiency with the raise of temperature, the mismatch of tracking control of the maximum power point, and the reduction of inverter efficiency with the input power phenomena. To estimate these loss factors from hourly measurement data, the system was evaluated by defining characteristic parameters. As a result, it was found that the main factors were the shadow effect and the mismatch loss, which reduce the mean annual output factor of the system to 65%. 3 refs., 6 figs., 1 tab.

Report on evaluation of research and development of superhigh-function electronic computers; Chokoseino denshi keisanki no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1973-02-20

Described herein is development of superhigh-function electronic computers.This project was implemented on a 6-year joint project, beginning in FY 1966, by the government, industrial and academic circles, with the objective to develop standard, large-size computers comparable with those of the world's highest functions by the beginning of the 70's. The computers developed by this project met almost all of the specifications of the world's representative, large-size commercial computers, partly surpassing the world's machine. In particular, integration of the virtual memory, buffer memory and multi-processor functions, which were considered to be the central technical features of the computers of the next generation, into one system was a Japan's unique concept, not seen in other countries. The other developments considered to have great ripple effects are seen in LSI's, and techniques for utilizing and mounting them and for improving their reliability. Development of magnetic discs is another notable result for the peripheral devices. Development of the input/output devices was started to correspond to inputting, outputting and reading Chinese characters, which are characteristics of Japan. The software developed has sufficient functions for common use and is considered to be the world's leading, large-size operating system, although evaluation thereof largely awaits the actual specification results. (NEDO)

Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

Interim evaluation report on research and development of robots serviceable under extreme conditions; Kyokugen sagyo robot no kenkyu kaihatsu chukan hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The research and development project for robots serviceable under extreme conditions are aimed at development of the robots for commercial nuclear power plants, where they are remotely controlled by the operators to implement advanced works, e.g., maintenance, inspection and repair of the facilities; supporting development of submarine oil fields, where they are remotely controlled by the operators to implement advanced works, e.g., maintenance, inspection and repair of the facilities; and for prevention of hazards at oil-producing plants, where they are remotely controlled by the operators to implement advanced works, e.g., controlling hazards, should they occur, and supporting hazard-preventive works. It is also aimed at development of the basic techniques for, e.g., those related to the system structures, and controlling and supporting the other systems. The project has been comprehensively evaluated for the achievements made so far. The individual elementary techniques for the robots for nuclear power plants, submarine oil field development and hazard prevention, and the basic techniques for these systems, are developed as planned as of the end of FY 1987 for the objects in the interim stage, based on the evaluation of the individual techniques developed before. Therefore, the bright prospects are obtained for achieving the final objectives by the end of the project period. (NEDO)

Fiscal 1993 achievement report on New Sunshine Program. Development of photovoltaic power generation system practicalization technology (Development of ultrahigh-efficiency solar cell technology - Development of crystalline compound solar cell technology); 1993 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu taiyo denchi no gijutsu kaihatsu (kessho kagobutsu taiyo denchi no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Efforts are made to enhance InGaP cell efficiency (target 16%) on a GaAs substrate by prolonging the InGaP minor carrier life span. In preparation of InGaP cell fabrication on silicon, a study is made of epitaxial growth of a wide band gap layer. By improving on the conditions of InGaP heteroepitaxial growth under the MOCVD (metal-organic chemical vapor deposition) method on a GaAs substrate, the InGaP cell base layer minority carrier life span is increased to be longer than 5ns. The use of epitaxial crystals greatly improves on the efficiency of InGaP cells on a GaAs substrate. Furthermore, cell structure improvement and the like are accomplished, which results in the achievement of an efficiency rate of 17.4%. As a basic technology for the fabrication of InGaP/Si tandem cells, experiments are conducted of growing a wide gap layer for the growth of Ln{sub 1-x}Ga{sub x}P on an silicon substrate. For the evaluation of epitaxial crystals and interfaces, time resolution photoluminescence measurement is performed and the result is compared with the result of simulation. (NEDO)

FY 1998 annual report on the researches on creation of inorganic thin films and fine particles of new functions; 1998 nendo shinkino muki usumaku biryushi no sosei kenkyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Creation of inorganic thin films and fine particles under a microgravity atmosphere is studied, for which Japan Microgravity Center's drop test facilities are used. The Cu anodic dissolution tests are conducted using a quasi-two-dimensional electrolytic cell, as part of the basic researches on micromachining for controlling high aspect ratio and shape anisotropy. It is difficult to control natural convection on the ground, even when the electrode thickness is decreased to 100 {mu}m or less. Concentration of the electrolytic solution over the anode surface is more supersaturated under a microgravity than on the ground. For production of fine glass particles, the liquid phase is involved between evaporation and solidification of glass. The Pb-X and Pb-Zn-X systems are molten, and dropped and, at the same time, solidified by quenching. The X component (including Zn) is uniformly dispersed under a microgravity in spheres of several to 20 {mu}m in diameter, although it is separated on the ground. The spherical droplets of GaSb can grow into a single crystal even in the absence of the seed, when supercooled and directed at high speed onto silica glass. A SiGe film with fine voids can be prepared and fast adhered to the base by flash lamp annealing, when it is deposited on the base with a SiN film as the buffer and then made into the film. (NEDO)

Fiscal 1976 Sunshine Project result report. Research on solar energy system (weather survey); 1976 nendo taiyo energy system no kenkyu seika hokokusho. Kisho chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-31

This report describes the fiscal 1976 research result on weather survey for solar energy systems. Study was made on preparation of the global solar radiation (GSR) map of Japan. To obtain the estimation equation of GSR based on related weather data, analysis was made on data at A type GSR observation sites and related weather data. As some factors effective for estimating monthly mean GSR, a relative sunshine duration, snowfall index (ratio of days more than 10cm in snowfall) and solar altitude index (sine of solar altitude at culmination hour) were selected. The estimation equation was prepared on the basis of these above factors. GSR was affected by relative sunshine duration exceedingly, snowfall by 12%, and solar altitude difference by 6% within an error of 5%. The monthly and annual GSR maps were prepared every site by the above calculation. The continuous observation results in Kagoshima and Fukuoka by recording direct pyranometers are presented. Scattered solar radiation is defined as the difference between simultaneously measured GSR and direct solar radiation. Weather data preparation in Fukuoka for design of solar cooling/heating and hot water supply systems is also described. (NEDO)

System approach on solar hydrogen generation and the gas utilization; Taiyo energy ni yoru suiso no seisei oyobi sono riyo system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujii, I; Hirooka, N; Deguchi, Y; Narita, D [Meiji University, Tokyo (Japan)

1997-11-25

An apparatus is developed to establish a system which allows utilization of hydrogen safely and easily, and its applicability to a hydrogen system for domestic purposes is tested. The system converts solar energy by the photovoltaic cell unit into power, which is used to generate hydrogen by electrolysis of water at the hydrogen generator, stores hydrogen in a metal hydride , and sends stored hydrogen to the burner and fuel cell units. It is found that a hydrogen occluding alloy of LaNi4.8Al0.2 stores hydrogen to approximately 80% when cooled to 20 to 25degC, and releases it to 10% when heated to 40degC. The fuel cell uses a solid polymer as the electrolyte. The hydrogen gas burner is a catalytic combustion burner with a Pt catalyst carried by expanded Ni-Al alloy. The optimum distance between the burner and object to be heated is 22mm. High safety and fabrication simplicity are confirmed for use for domestic purposes. The system characteristics will be further investigated. 4 refs., 8 figs.

Survey for development feasibility in fiscal 1999 investigation of geothermal development and promotion. Evaluation report on practicability technology survey SWD method (Evaluation report concerning verification test); 1999 nendo chinetsu kaihatsu sokushin chosa no uchi kaihatsu kanosei chosa. Jitsuyoka gijutsu chosa SWD ho hyoka hokokusho (jissho shiken ni kakawaru hyoka hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

An evaluation test was conducted on SWD (Seismic While Drilling) method as a part of the investigation of geothermal development and promotion. The test was implemented at the time of drilling of N11-MD-3 well in the northeast base area of Busadake, Hokkaido. The test items were such as verification of direct waves propagating from a bit to the surface, identification of signals passing through a fault zone using direct waves and reflected waves, estimation of distance between a fault and a bent zone, and grasping the direction of signal propagation at the time of inclined drilling. As a result of the experiments and studies, following conclusions were obtained. Reflected waves extracted are not necessarily limited to those from a reflection area from which the shape of a fault can be grasped; unless there is a clear reflection area that can be picked up on the surface near a fault, the application of this method is not effective. In an analysis using direct waves, it was possible to obtain an inclined angle of a fault plane from the estimation of velocity structure, propagation route, and assumption of the shape of the fault plane and, therefore, to grasp the shape of the fault. Obtaining reference data is essential for identifying bit signals. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture high-quality amorphous materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

These technological developments are intended to develop technologies to manufacture with improved quality the silicon-based thin film solar cells. In order to analyze manufacturing conditions for micro crystal silicon thin films as the narrow-gap amorphous silicon-based films, films were manufactured in the vicinity of borders of amorphous/micro crystal silicon film manufacturing conditions. The present film manufacturing did not present effects of suppressing deterioration of hydrogen diluted light. In order to elucidate the light deterioration mechanism in hydrogenated amorphous silicon films and study the suppression thereof, discussions were given on impurities in the film, including oxygen. By using an ultra high vacuum plasma CVD having a thoroughgoing baking system, an oil-free exhaust mechanism, and a raw material gas refining mechanism, impurities were added to and removed from a reaction vessel, and an ultra-high purity Si:H film was manufactured, which has been removed of impurities from the raw material gas, resulting in reduction of O, C and N standing no comparison. According to the result of a light irradiation experiment on an ultra-high purity film obtained under an accelerated deteriorating condition by using a pulse laser, the model assuming the light induced defect and the pair of impure atoms has been denied. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Volume 1. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture low-cost large-area modules and survey and research on analyzing how to put products into practical use); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu 1))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to assist research and development to put thin film solar cells for power use into practical use and a research to put thin film solar cell manufacturing technologies into practical use, survey and research have been performed on trends in the technologies inside and outside the country. Characteristic points in thin film solar cells during the current fiscal year include: expansion of production scale of amorphous silicon solar cells, rapid progress in poly-crystalline silicon thin film solar cell technologies, and enhancement of performance in large-area modules in the a-Si, CIGS, and CdTe systems. In the trends in research and development of amorphous systems, expectation is heightening on elucidation of optical deterioration phenomena, and establishment of suppression technologies thereof. Although the highest efficiency was not renewed in thin film solar cells of small areas, progress was seen in the post-stabilization efficiency in large-area modules. A thin film solar cell manufacturing plant having an annual production capacity of 20 MW was put into operation in October in Japan. Micro (poly) crystalline silicon based solar cells have high possibility of being compatible in cost reduction and performance improvement, and energetic researches are being carried out on them in recent years as the most promising candidate of the next generation solar cells. (NEDO)

Evaluation report on research and development of a subsea petroleum production system; Kaitei sekiyu seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

In order to assure stable supply of oil and natural gas resources, and achieve enhancement in ocean development technologies in general, development has been made on the subsea petroleum production system (SBPPS), which is effective in ocean floor petroleum production from oil fields at great depths (300 m or deeper), and can be applicable to continental shelves and continental slopes around Japan. The SBPPS consists of four sub-systems of shafts, pipelines, manifolds, and riser and oil storage, whose basic development targets were established for the total system. The system was given a conceptual design for the total system, and the above four sub-systems were designed according to the conceptual design. The experimenting devices of each system were fabricated on a trial basis while fundamental studies are being made on component technologies, and experiments were performed to verify basic functions of the sub-systems. Developments were made on such operation technologies as the system operation technology, production control technology, safety control technology, and maintenance and repair technology required to operate the SBPPS. On-shore and general off-shore experiments were carried out to verify the functions of the experimenting devices of each system, the comprehensive functions and the operation technology. Comprehensive evaluation was given on the above achievements from the technical, economic and social viewpoints. (NEDO)

Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

Interim report on evaluation of research and development of manganese nodule exploitation system; Mangan dankai saiko system no kenkyu kaihatsu chukan hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

This research and development project is aimed at development of the techniques which allow exploitation of manganese nodules occurring on deep sea bottoms (4,000 to 6,000 m deep) on a commercial scale, in order to secure stable supply of the non-ferrous metallic resource and improve general ocean development techniques. This project, established by the national project system, has been implemented cooperatively by the government, academic and industrial circles since 1981. Described herein are the interim results, summarized in the FY 1985. The targets of the phase for developing the individual techniques were set to develop the exploitation system design procedures, and to advance to the next phase by the end of FY 1985, where the consistent, integrated system is to be constructed and tested. The results obtained so far are satisfactory as a whole, both in the elementary techniques and their consistency. The simulations have been conducted, where various conditions are inputted to estimate the movement and exploitation characteristics of the system as a whole in the comprehensive ocean tests. It has been found that the nodule-collecting machine shows nonlinear tracking characteristics (i.e., movement different from that of the exploitation ship), and unsteady movements (i.e., repeated movements of rapid starting and stopping). (NEDO)

Study on the inside gas flow visualization of oxygen sensor cover; Kashika ni yoru O2 sensor cover nai no gas nagare hyoka

Energy Technology Data Exchange (ETDEWEB)

Hocho, S; Mitsuishi, Y; Inagaki, M [Nippon Soken, Inc., Tokyo (Japan); Hamaguchi, S; Mizusawa, K [Toyota Motor Corp., Aichi (Japan)

1997-10-01

In order to make clear the difference of the response time between the oxygen sensors with different protection covers, we visualized gas flow inside of sensor covers by means of two experimental methods: One is `Smoke Suspension Method` using liquid paraffin vapor as the smoke. With smoke suspension method, we detected the streamlines inside of the covers. The other is `Color Reaction Method` using the reaction of phenolphthalein and NH3 gas. With color reaction method, we confirmed the streamline inside of the cover and furthermore detected the difference of the response time of each sensor. 3 refs., 7 figs., 1 tab.

Evaluation report on the development of an advanced refrigerant for compression heat pumps; Asshukushiki heat pump yo shinki reibai kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The research and development were reported on new refrigerants for compression type heat pumps. From 64 kinds of newly composed ether, CF3CF2OCH3 was developed as candidate compound substituting for CFC-11, and CF3CF2CF2OCH3 and (CF3)2CFOCH3 as those substituting for CFC-11. However, COP of the refrigeration has not been optimized. Global warming potentials were obtained by high-accuracy estimate guidelines. The new refrigerants have no chlorine and therefore no effects on the ozonosphere. Global warming effects also satisfied the present allowable values. There was no problem on human body toxicity in the short-term experiment. Costs of commercially production of the candidate compounds were trially calculated from reaction paths and chemical constitution formulae. Assuming that the raw materials are circulating on the market, plant/equipment investment, production volume, and production cost became 5 billion yen, 1000 tons/year, and 3500-6500 yen/kg in 3 persons/shift and 4 shifts, respectively. This is close to the allowable level which is ten times the CFC-12 price, 5000 yen/KG. The new refrigerants are expected to be fully commercialized in consideration of progress of the composition method and improvement of physical properties in the future. 115 refs., 37 figs., 102 tabs.

Evaluation report on the R and D of the membrane separation process introduction technology; Makubunri process donyu gijutsu no kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper reported the R and D of the membrane separation process introduction technology during a period of 1994 through 1998. The membrane separation technology is not associated with the phase change which requires large energy and expected to be an energy saving process. For the production of membranes required of high functions, the vapor deposition polymerization method was considered, and high order structure control of the membrane, control of adhesion and attachment, and control of orientation, and development of the high polymerization technology were required. For the high grade control of vapor polymerization, the substrate surface structure/quality were important. The molecular level analysis of the vapor deposition surface was also needed. Therefore, the paper took notice of STM (scanning tunneling microscopy), AFM (atomic force microscopy) and HREELS (high resolution electron energy loss spectroscopy) as surface atomic/molecular configuration analysis technology, and designed/fabricated and studied the high resolving power and high sensitivity analysis equipment using the analysis equipment which combined HREELS and STM and the analysis equipment using SFG (sum frequency generation) which can detect signals in the low frequency region. Making full use of the highest technology, technology was able to be developed for substrate surface analysis and surface reaction analysis technologies which become the basis of the high performance separation membrane fabrication technology by the vapor deposition polymerization method indispensable for introduction of the membrane separation process. The technology can be the base applicable to a lot of fields where surfaces and interfaces are concerned

Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

Toxicity evaluation of chlorinated organic compounds using immortalized rat hepatocytes; Fushika rat kansaibo wo mochiita yuki enso kagobutsu no dokusei hyoka no kokoromi

Energy Technology Data Exchange (ETDEWEB)

Sone, H; Nakajima, M; Yonemoto, J [National Institute for Environmental Studies, Tsukuba (Japan)

1997-11-10

Chlorinated organic compounds has high priority for toxicity screening among environmental hazardous chemicals. In the present study, we used immortalized rat hepatocytes as a liver model in vitro to evaluate the toxicity of nine chlorinated organic compounds. Toxicity of nine chlorinated organic compounds were evaluated to cellular viability of immortalized rat hapatocytes. The potency of the toxicity based on 50% inhibitory concentration (IC50) value was in the following order: triclocalban>triclosan>3,4-dichloroaniline>2,5-diclorophenol> 2,5-dichloroanisole>p-dichlorobenzene> p-chloroaniline>o-dichlorobenzene=tris (2-chloroethyl) phosphate. The rank order of cytotoxic potency of nine chemicals was compared with toxicity information using animals. The rank order of cytotoxic potency did not relative to the order referenced mean lethal dose (LD50) as an index of acute toxicity of rats or mice. However, the rank order of cytotoxic potency relatively correlated non-observed adverse effect level (NOAEL) under the exposure duration adjusted for chronic toxicity in vivo. These data suggests that the origin of testing cell had better to make match target organ of toxic chemicals for extrapolation from data of bioassay in vitro to in vivo. 16 refs., 2 figs., 3 tabs.

Evaluation of indoor thermal environment with improved 65 nodes thermoreguration model; Kairyogata 65 bunkatsu taion chosetsu model wo mochiita shashitsunai onnetsu kankyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Matsunaga, K; Sudo, F [Isuzu Motors Ltd., Tokyo (Japan); Tanabe, S [Ochanomizu Univ., Tokyo (Japan)

1997-10-01

Indoor thermal environment of a vehicle was evaluated by a numerical simulation. A numerical simulation using the equivalent temperature measured with the thermal manikin was conducted. Numerical manikin was improved and convective and radiative heat transfer at each body surface was described in detail. Comparative examination using the calculation results by the numerical simulation was also conducted. 3 refs., 8 figs., 2 tabs.

Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (photovoltaic power generation); Taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

This report summarizes the research result on the guide for developing solar cells. The report includes (1) standard measurement method for solar cells, (2) system configuration and installation site, (3) optimum design and profitability of solar cells and (4) raw materials and pollution prevention. In the 1st research, study was made on the standard for solar radiation intensity, the definition and measurement methods for spectral profiles, and the measurement conditions for solar cells. In the 2nd research, study was made on various basic data for the scale of photovoltaic power systems. In the 3rd research, since it is necessary to obtain characteristics of solar cells with any profiles of physical constants such as impurity, minority carrier life and mobility by simulation of solar cell actions, research was made on the measurement method of minority carrier lives by using a prepared computer program. Technical and economical comparisons were also made between Si solar cells with various structures. In the 4th research, survey was made on various data for compound semiconductors, and study was made on industrial waste pollution. (NEDO)

Dependence of open-circuit voltage of SnO2-nSi solar cells; SnO2-nSi taiyo denchi no sanka ondo menhoi izonsei

Energy Technology Data Exchange (ETDEWEB)

Shinoda, S; Shimizu, A; Yano, K; Kasuga, M [Yamanashi University, Yamanashi (Japan). Faculty of Engineering

1997-11-25

Although metal(or semiconductor)-semiconductor solar cells, SnO2-nSi solar cell for example, are superior in cost and efficiency, its barrier height and open-circuit voltage V(oc) are lower than those of p-n junctions. To improve these defects, study was made on the dependence of V(oc) on oxidation temperature and surface orientation using various solar cells prepared from (100)Si and (111)Si under various oxidation conditions. As a result, the density of surface states increases with a decrease in oxidation temperature of Si substrates, resulting in an increase in diode factor and V(oc). In this case, since oxide films are extremely thin and contribution of non-terminated bonds is large in the initial oxidation stage, the quantity of dangling bonds is larger in (100) plane than (111) plane, resulting in an increase in diode factor and V(oc). Since the surface energy level (the degree of electrons dominated by acceptor-like surface state from this level to the top of a valence band) of (100) Si is lower than that of (111) Si, the effective barrier height and V(oc) increase. 28 refs., 6 figs., 2 tabs.

Reports on 1979 result of Sunshine Project. Research on solar energy system (meteorological investigation); 1979 nendo taiyo energy system no kenkyu seika hokokusho. Kisho chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-31

The following were implemented with the purpose of collecting, measuring and putting in order the meteorological data required for the R and D on solar energy technology. (1) Observation of direct solar radiation (Nagoya/Sendai), (2) Meteorological observation for the pilot plant site of 1,000kW solar thermal power generation, (3) Studies on estimation of quantity of direct solar radiation, and (4) Studies on characteristics of quantity of direct solar radiation. In (1), the summary and the results were explained on the continuous observation of the quantity of the direct solar radiation conducted in Nagoya and Sendai using a self-recording actinometer. In (2), meteorological observation was conducted for building lots reclaimed from a salt pan at Nio-cho, Mitoyo county, Kagawa prefecture, a scheduled site for the pilot plant. The items were the quantity of global solar radiation, quantity of sky solar radiation, quantity of direct solar radiation, temperature, wet-bulb temperature, wind direction and wind velocity. In (3), A method was developed for estimating the monthly average quantity of the global solar radiation, normal direct solar radiation, horizontal sky solar radiation at an arbitrary spot. In (4), the characteristics of direct/specified direct solar radiation flux curves were elucidated as the basic data for the technological development of solar energy utilization using a sun follower type heat collecting device, with research done on a method for estimating these curves from other meteorological factors. (NEDO)

Japan`s New Sunshine Project. 1994 annual summary of solar energy R and D program; 1994 nendo new sunshine keikaku. Seika hokokusho gaiyoshu (taiyo energy)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-01

The paper reported the results of fiscal 1994 studies on solar energy in the New Sunshine Project. Relating to the technical development for the practical use of photovoltaic power systems, the development of manufacturing technologies for low-cost substrates and the development of element technology for manufacturing low-cost polycrystalline cells/modules were reported as the development of technology for thin substrate polycrystalline solar cells for practical use. As to the research on fabrication technology for thin film solar cells for practical use, reports were made on the research on low-cost fabrication technology for large-area modules and the technological development for qualitative improvement, etc. In respect to the technological development for super-high efficiency solar cells, reported were the technological development for super-high efficiency single crystalline silicon solar cells and the technological development for crystalline compound solar cells, etc. Concerning the research and development of photovoltaic power systems, reports were on the characterization and control of surface/interface recombination velocity of crystalline silicon thin films and the research on surface passivation for high-efficiency silicon solar cells, etc. In regard to the utilization technology of solar thermal energy, the energy conversion technology using chemical reactions and the development of chemical refrigeration and cold storage systems using solar heat were reported as the research and development of utilization technology of solar thermal systems for industrial use.

Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (solar furnace); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoro

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

For solar furnace, study was made on analysis of its use purpose, analysis of the profitability of large furnaces, safety, maintenance, solar radiation and construction site conditions. On production of fused refractories by solar furnace, in particular, giving attention on zircon sand and mullite, their fusion property was clarified, and their fine structure was obtained by rapid heating/cooling. On production of Si by solar furnace, in this fiscal year, in particular, study was made on the 1st step (production of coarse Si from silica rock) and 4th step (deposition of Si by decomposition of SiHCl{sub 3}). On study on high-temperature processing followed by chemical reaction, study was made on production of carborundum by solar furnace, its application to high-temperature gas reaction, and its application to heat storage by high-temperature chemical reaction. In addition, for large solar furnace, study was made on its maintenance, safety, pollution problem, and construction site condition based on estimation of direct solar radiation profile maps. Inlands of Tokai, Kii-Hanto and Seto-Naikai districts were confirmed to be suitable for solar furnaces. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In relation with several types of standard photovoltaic power generation systems expected to be put to practical use, design parameters are quantified, databases are utilized, and simulation technologies are developed, while collecting data from test facilities constructed to simulate them, for the development of evaluation techniques indispensable for the efficient improvement of photovoltaic power generation systems. In fiscal 1998, data were collected from verification test facilities and residential photovoltaic systems sited across Japan. The collected data were subjected to analysis and simulation, by which correction factors were calculated for smudge, spectral response, incident radiation, and temperature. Furthermore, load matching factors and storage battery contribution rates were calculated by simulation for the stand-alone photovoltaic systems sited in five Japanese cities, each comprising an array, storage battery, charge/discharge controller, DC-DC converter, and a load. Reference is also made to a survey of trends of technology development. (NEDO)

Preparation and properties of TiO2 films by complexing agent-assisted sol-gel method. Yuki haiishi wo mochiita sol gel ho ni yoru TiO2 usumaku no sakusei to seishitsu

Energy Technology Data Exchange (ETDEWEB)

Nishide, T [Nissan Motor Co. Ltd., Tokyo (Japan); Mizukami, F [National Chemical Laboratory for Industry, Tsukuba (Japan)

1992-09-01

In order to control optical properties of TiO2 thin films, the TiO2 films were prepared by the sol-gel method using glycols or their ether derivatives as organic ligands to study the effect of the organic ligands on the refractive indices and crystal phases. Samples were prepared as follows: Organic ligand was added into the ethanol solution of Ti(O-iso-pr) 4, and aqueous nitric acid solution was added after reflux, and sol obtained by subsequent reflux was applied on soda lime glass or silicon wafer substrates, which were baked at 400 to 900 centigrade. Three kinds of ligand such as 2-(2-methoxyethoxy) ethanol were used. Measured items are the film thickness, thermal characteristics, crystal phase and refractive indices of thin films. The key points are as follows: In case of TiO2 thin films on the soda lime glass substrate, the changing pattern of refractive indices by temperature changes with the kind of ligand used and further the peak strength of anatase changes with the kind of ligand used. In case of silicon wafer substrates, the peak strength of anatase and rutile changes with the kind of ligand. The refractive indices and crystal phase can be controlled by properly using the ligand. 7 refs., 11 figs.

Development of new technologies for high quality thin film and its application to energy engineering; Hikari seigyo to sokudo senbetsu ni yoru chokinshitsu usumaku no seisaku to energy bun`ya eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Hijikata, K; Inoue, T; Nagasaki, T; Suzuki, Y; Sato, I [Tokyo Institute of Technology, Tokyo (Japan); Nakabeppu, O [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1997-02-01

This paper describes laser irradiation and velocity selective deposition experiments for fabricating high quality thin films. For the formation of Ag thin film by vacuum deposition method, YAG laser was irradiated to atoms or clusters parallel or perpendicular to the NaCl single crystal substrate, to deposit them on the substrate. For another experiment, Ag atoms selected in the given velocity were deposited on the (001) NaCl substrate by passing the molecular beam through the velocity selector. When laser was not irradiated, the thin film showed a random structure. Epitaxial growth was accelerated by the laser irradiation. When the selective velocity was set in 353 m/s at the constant intensity of molecular beam, the diffraction pattern of the thin film showed net pattern. When the selective velocity was set in 529 m/s, a structure in which ring pattern was overlapped on the net pattern was obtained. 2 figs.

Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research and development of technologies for enlarging amorphous solar cell area); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (amorphous taiyo denchi no daimensekika gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In the basic studies of large-area a-Si film formation technologies, the validity is discussed of the evaluation technique using plasma optical emissions spectrometry (OES) employed for the achievement of the intended film qualities. The film forming condition that exerts the greatest influence on the plasma state relative to OES is the power of discharge, and correlations are found to exist between specific emission intensity, infrared absorption level, and photoconductivity of the film. It is found that a P- or B-doped Si:H/SiC:H film is suitable as the material for the window layer on the light-receiving surface of the solar cell. Materials are studied for the i-layer responsible for photo carrier generation, isolation, and acceleration. Studies are also conducted on fluorine-containing film. In the efforts at designing and building solar cells, ITO (indium-tin oxide)/n-i-p/SS (reversed type) cells are analyzed, designing is carried out for transparent electrode film thickness optimization, window effect in stainless substrate cells is improved, glass substrate cells are experimentally built and analyzed, large-area solar cell properties are improved, interaction between the substrate and a-Si is studied, and reliability tests are conducted. For cost reduction, it is necessary to develop technologies of automated production of simplified-structure modules using low-cost materials. Basic matters are taken up for discussion. (NEDO)

Achievement report on research and development of optics-aided measurement/control system; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

The project aims to establish technologies for putting the above-named system to practical use. Such a system will measure, transmit, and control, with safety and stability by use of optical technologies, industrial process related information to be generated in certain areas such as industrial complexes and very large plants, the information including images, temperatures, flow rates, constituents, etc. Total system evaluation was performed in demonstration tests for appropriateness conducted for 32 systems in fiscal 1980 and 10 systems in fiscal 1981. Studied in the development of element technologies are opto-electronic integrated circuits (OEIC), semiconductor laser devices, light-intercepting devices, optical transmission paths, dielectric light switches, and optical sensors. For OEIC, in particular, since it is believed to be the nucleus of an optical application system, an optical technology joint research office is established, where efforts center on the substrate crystal growth technology, process technology, and crystal/process evaluation technology. (NEDO)

Evaluation report on research and development of 'seawater purification and byproduct utilization'; 'Kaisui Tansuika to fukusanbutsu riyo' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-01

Research, development, and evaluation were made on seawater purification for the purpose of supplying inexpensive city water stably in the future. In the research of the high flow rate long-tube type multi-stage flash process, basic characteristics were identified by studying fluidity, heat transfer, deaeration, and decarburization by using a test plant with a capacity of 3,000 m{sup 3}/d. A number of findings were derived in carrying out demonstration studies by using a test module with a capacity of 100,000 m{sup 3}/d. Research on heat transfer pipe materials covered a wide area including copper alloys, titanium and aluminum alloys, and ferrous materials, where a prospect was obtained on materials which may be practically usable in the future as transfer pipes in large seawater purifying equipment. Research on a concrete evaporator body proved that it is more economical than steel evaporators, and has sufficient corrosion resistance even against high-temperature brine. Other activities included researches on effects of contaminated seawater, brine diffusion, byproduct utilization, and total systems. Social and economic evaluations were also performed. (NEDO)

Evaluation report on the development of ultra-solid lubricant with cluster diamond; Cluster diamond wo riyoshita kotai junkatsu fukugo zairyo no kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The fiscal 1998-2000 results of efforts to develop cluster diamond (CD)-diffused solid lubricant composite materials expected to exhibit excellent lubrication are stated. Since friction greatly affects machine life and energy efficiency, friction reduction is an important task. Very hard and microscopic CD was utilized for the achievement of a friction coefficient of 0.08. A manufacturing technology for molds 10nm or smaller was developed, which enabled the development of a gear not larger than 8mm. The success will enable the operation of micromachines in the absence of lubrication which is impossible at present. A CD-aided functional layer creation technology was also developed. It is expected that the development and practical application of micromechanisms will make rapid progress in the 21st century. Much is expected from the creation, and goods with the achievement applied thereto, of advanced technologies whereinto non-lubrication, functional layer creation, and excellent heat conductivity are incorporated. It is quite significant that, since CD is available in any field as far as light-load low-speed sliding conditions are satisfied, sliding parts will be improved and service life will be prolonged. (NEDO)

Study on state grouping and opportunity evaluation for reinforcement learning methods; Kyoka gakushuho no tame no jotai grouping to opportunity hyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yu, W.; Yokoi, H.; Kakazu, Y. [Hokkaido University, Sapporo (Japan)

1997-08-20

In this paper, we propose the State Grouping scheme for coping with the problem of scaling up the Reinforcement Learning Algorithm to real, large size application. The grouping scheme is based on geographical and trial-error information, and is made up with state generating, state combining, state splitting, state forgetting procedures, with corresponding action selecting module and learning module. Also, we discuss the Labeling Based Evaluation scheme which can evaluate the opportunity of the state-action pair, therefore, use better experience to guide the exploration of the state-space effectively. Incorporating the Labeling Based Evaluation and State Grouping scheme into the Reinforcement Learning Algorithm, we get the approach that can generate organized state space for Reinforcement Learning, and do problem solving as well. We argue that the approach with this kind of ability is necessary for autonomous agent, namely, autonomous agent can not act depending on any pre-defined map, instead, it should search the environment as well as find the optimal problem solution autonomously and simultaneously. By solving the large state-size 3-DOF and 4-link manipulator problem, we show the efficiency of the proposed approach, i.e., the agent can achieve the optimal or sub-optimal path with less memory and less time. 14 refs., 11 figs., 3 tabs.

Estimation of durability of GFRP laminates under stress-corrosive environments using acoustic emission; AE wo mochiita ouryoku fushoku kankyoka deno GFRP no taikyusei hyoka

Energy Technology Data Exchange (ETDEWEB)

Fujii, Yoshimichi. [Seikow Chemical Engineering and Machinery, Ltd., Hyogo (Japan). Laboratory of Composite Materials; Nishiyabu, Kazuaki. [Osaka Prefectural College of Tehcnology, Osaka (Japan)

1999-05-15

The objective of this investigation is to estimate the creep life of glass fiber reinforced plastic (GFRP) under stress-corrosive environments using acoustic emission(AE). The laminates were fabricated using combinations of vinylester resin (R806) and random fiber mat or woven cloth. The creep tests were conducted in 5% nitric acid (HNO{sub 3}) environment. The AE depends on the loading level and the environment condition. For the creep test, the woven cloth reinforced specimens gave higher number of AE counts than the random mat reinforced specimens. The creep life decreased with increasing creep stress, whereas the rate of AE counts increased with increasing creep stress. A linear relationship was found between the creep life and the AE count rate. Using the proposed equation, a prediction of the creep life of GFRP under corrosive environments would presumably be possible. (author)

Fault fracture zone evaluation using borehole geophysical logs; case study at Nojima fault, Awaji island; Kosei butsuri kenso ni yoru danso hasaitai no hyoka

Energy Technology Data Exchange (ETDEWEB)

Ikeda, R; Omura, K [National Research Institute for Disaster Prevention, Tsukuba (Japan); Yamamoto, T [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)

1997-10-22

Ikeda, et al., in their examination of log data obtained from a borehole (2000m deep) drilled at Ashio, Tochigi Prefecture, where micro-earthquakes swarm at very shallow levels, pay special attention to porosity. Using correlationship between the porosity and elastic wave velocity/resistivity, the authors endeavor to find the presence of secondary pores, dimensions of faults, composition of water in strata in faults, and difference in matrix between rocks, all these for the classification and evaluation of fault fracture zones. In the present report, log data from a borehole (1800m deep) drilled to penetrate the Nojima fault (Nojima-Hirabayashi, Awaji island) that emerged during the Great Hanshin-Himeji Earthquake are analyzed in the same way as the above-named Ashio data, and the results are compared with the Ashio results. Immediately below the Nojima-Hirabayashi fault fractured zone, stress is found remarkably reduced and the difference stress quite small in size. This is interpreted as indicating a state in which clay has already developed well in the fault fractured zone ready to allow the occurrence of shear fracture or a state in which such has already occurred for the release of stress. 4 refs., 5 figs.

Evaluation report on research and development of an ultra-advanced processing system. 3; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-08-01

This paper describes comprehensive evaluation on the following technologies as the ultra-advanced processing system: (1) large output excimer laser, (2) high-density ion beam, (3) an ultra-precision machining device, (4) ultra-advanced processing, (5) measurement and evaluation, and (6) comprehensive test. In the item (1), research and development was performed on such technologies as output increasing, output stabilization and beam formation, having achieved the targets. In the item (2), research and development was performed on such technologies as beam convergence, plasma control, ion transportation, high-frequency quadruple pole acceleration, and large-capacity class ion beam, having achieved the targets. In the item (3), research and development was performed on form creation and ultra-precision machining, having achieved the targets. In the item (4), research and development was performed on formation of high function thin films to apply the laser abrasion process to large area, ion surface modification, wide band area optics, high reflectance optics, ion injection, dynamic mixing, and modification of ultra high-grade metal surface, having achieved the targets. In the item (5), research and development was performed on high-accuracy roughness measurement, shape measurement, optical property evaluation, a wavelength meter, ultra advanced processing standard measurement, and environment correction technology, having achieved the targets. In the item (6), comprehensive demonstration was carried out on the component technologies. (NEDO)

Interim report on evaluation of research and development of manganese nodule exploitation system; Mangan dankai saiko system no kenkyu kaihatsu chukan hyoka chukan hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-05-01

This research and development project is aimed at development of the techniques which allow exploitation of manganese nodules occurring on deep sea bottoms (4,000 to 6,000 m deep) on a commercial scale, in order to secure stable supply of the non-ferrous metallic resource and improve general ocean development techniques. This project, established by the national project system, has been implemented cooperatively by the government, academic and industrial circles since 1981. Described herein are the interim results obtained by the FY 1984. The bases for development of the elementary techniques have been established for the comprehensive ocean tests. Bright prospects have been obtained to achieve the objectives, although there are some problems remaining to be solved. Interfaces between the sub-systems are being reviewed mainly by the persons in charge of the total system. No problem is foreseen in consistency of the individual components. The movement and exploitation functions of the test system are simulated and validated in detail, to develop the total system. It has been found by the simulations that the nodule-collecting machine shows nonlinear tracking characteristics (i.e., movement different from that of the exploitation ship), and unsteady movements (i.e., repeated movements of rapid starting and stopping). (NEDO)

Coal structure construction system with construction knowledge and partial energy evaluation; Kochiku chishiki to bubunteki energy hyoka ni yoru sekitan bunshi kozo kochiku system

Energy Technology Data Exchange (ETDEWEB)

Okawa, T.; Sasai, T.; Komoda, N. [Osaka University, Osaka (Japan). Faculty of Engineering

1996-10-28

The computer aided coal structure construction system is proposed, and a computational construction example is presented. The coal structure construction engine of this system fabricates molecular structure by connecting fragments sequentially inputted through a user interface. The best structure candidate is determined using construction knowledge and partial energy evaluation every addition of one fragment, and this process is subsequently repeated. The structure evaluation engine analyzes the 3-D conformation candidate by molecular dynamics, and evaluates the conformation by determining the energy value of an optimum structure. As an example, this system was applied to construction of coal molecular structure based on the actual data of partial structure composed of 26 structures from 2l kinds of aromatic cluster structures, 27 bonds from 2 kinds of bridged bonds, and 16 groups from 2 kinds of terminal substitutional groups. As a result, this system could construct a superior structure according to expert knowledge from the viewpoint of energy. 6 refs., 5 figs., 2 tabs.

Investigation on the chemically fixing technique of carbon dioxide utilizing solar energy; Taiyo energy riyo ni yoru nisanka tanso no kagakuteki koteika gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

This report describes the results of effective fixing technique of CO2 by utilizing solar energy. First of all, the investigation was directed to the technique for synthesizing ethylene, hydrocarbons and alcohol by electrochemical reduction of CO2. The power required for this process is supplied by photovoltaic power generation. Development of excellent electrode catalyst is needed because the reduction of CO2 requires a high overvoltage. It is desirable to enhance the selectivity of the reaction for specific material and improve the transport process in the electrolytic cell. Next, designing of material and reaction of photocatalysts using semiconductor electrode and semiconductor particulate was examined. A semiconductor electrode made of FeS2 is inexpensive and has a high ability of collecting solar light. In the category of photocatalysis system, a photocatalytic system in which semiconductor particles are embedded in vesicle and a photpocatalyst based on potassium niobate are noteworthy. As biosystem, the method of reducing CO2 by calcareous algae which simultaneously advances fixing and calcification of CO2 by photosynthesis is noteworthy. 129 refs., 45 figs., 20 tabs.

Shunt and series resistance of photovoltaic module evaluated from the I-V curve; I-V tokusei kara hyokashita taiyo denchi no shunt teiko to chokuretsu teiko

Energy Technology Data Exchange (ETDEWEB)

Asano, K; Kawamura, H; Yamanaka, S; Kawamura, H; Ono, H [Meijo University, Nagoya (Japan)

1997-11-25

With an objective of discussing I-V characteristics when a shadow has appeared on part of a photovoltaic module, evaluations were given as a first stage of the study on saturation current, shunt resistance and series resistance for the solar cell module. As a result of measuring change in amount of power generated in a sunny day with a shadow appearing over the solar cell module, reduction in power generation capability of about 23% was verified. In other words, the I-V characteristics of the solar cell module change largely because of existence of the shadow caused on the module. The I-V characteristics curve may be expressed and calculated as a function of the shunt resistance and series resistance. By curve-fitting measurement data for a case of changing insolation without existence of partial shadow, values of the shunt resistance and series resistance were derived. As a result, it was found that the calculations agree well with measurements. It was made also clear that each parameter shows temperature dependence. 6 refs., 10 figs., 1 tab.

Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (total system); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Total system

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

For every solar energy utilization field, its background, feasibility, impact in practical use, and R and D policy in Japan were studied. Heating and hot water supply by solar energy are already practical because of less technical problems and reasonable profitability, and cooling is also practical as far as a technical viewpoint. At present, the technical level of solar heat power generation is in the stage of basic technology, however, in the future, development of economically reasonable systems will be demanded as well as establishment of its technology. The most difficult problem for realizing practical solar cell power generation systems is cost reduction. It is also another problem that a big demand of Si for solar cells further exceeds the current yield of Si in a semiconductor industry. A small-scale hybrid solar cell power generation system applicable to the roof of general residences is already feasible. Although a solar furnace is still poor in application to industrial fields, it is expected as the leading part for a future solar heat chemical industry. (NEDO)

Study of installation of PV systems at campus; Campus ni okeru taiyoko hatsuden donyu ni kansuru kenkyu (taiyo denchi nomi wo secchishita baai no yobi kento)

Energy Technology Data Exchange (ETDEWEB)

Tsuboi, N.; Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

1997-11-25

In terms of energy consumption, environmentality and economical efficiency in the case of installing the photovoltaic power system on the rooftop of the university campus, a comparative study was conducted with other power generation systems. As objects to be comparatively studied, selected were the all-electric type centralized space heating/cooling system, cogeneration system, nighttime heat storage system and centralized system with solar cells installed. The panel area of the PV system is 10,000m{sup 2} on the rooftop and 7,000{sup 2} on the outer wall. About data on solar radiation, average values obtained in Nagoya were used. Assessment was made in terms of energy consumption amount at the time of operation, system COP, emission amounts of CO2, NOx and SOx at the time of manufacturing and operation, initial cost, running cost, etc. As a result of the study, an effect of reducing global warming gas was admitted in the PV system. However, the initial cost of the solar cell panel was high, and the life cycle cost of the PV system was lower than other systems. 1 ref., 7 figs., 3 tabs.

Method for estimation of the spectral distribution that influence electric power of PV module; Taiyo denchi shutsuryoku ni eikyo wo ataeru bunko nissha bunpu no suiteiho

Energy Technology Data Exchange (ETDEWEB)

Yamagami, Y.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

1997-11-25

A method was proposed for estimating the spectral distribution using air mass, precipitable water, and clear indexes which are generally obtainable, and a comparative study was made between the spectral distribution obtained by this method and the measured data using output power of PV modules, etc. as indexes. When solar light comes into the atmosphere, it dissipates receiving scattering/absorption by various gases and aerosols. Direct light component and scattered light component which arrive at the earth surface become functions of air mass and precipitable water. The wavelength distribution of scattered light in cloudy sky is not dependent upon air mass, but affected strongly by absorption band by steam of clouds. By relational equations considered of these, output power and short-circuit current of PV modules are obtained to make a comparison with the measured data. As a result, it was found that this method estimated the spectral distribution with accuracy. Further, seasonal changes in the spectral distribution were well reproduced. The simulation of the module output in Sapporo and Okinawa brought a result that the output in Okinawa is 1.93% larger than in Okinawa. 5 refs., 5 figs., 6 tabs.

Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (total system); 1974 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Total system

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

The current most important solar energy utilization fields are solar energy power generation (solar heat and photovoltaic power generation), and solar heat cooling and heating. A solar heat power system collects or stores solar thermal energy as energy source of power systems, and converts it to electric power through heat exchange systems. To establish such system, not only R and D on a collector, absorption capsule, storage unit and heat transfer unit, but also complete study on an optimum system configuration and environmental impact are necessary. A photovoltaic power system converts solar energy to electric power directly by photoelectric conversion device such solar cell. Except specific local uses, drastic cost reduction and improvement of a conversion efficiency (at present 12-15%) and life (several years) are necessary for solar cells. Although a lot of solar heat cooling and heating systems is in practical use in Japan, for its further diffusion an important research task is development of heat collector excellent in efficiency, cost, life and maintainability. (NEDO)

Technological development for super-high efficiency solar cells. Survey on the commercialization on analysis; Chokokoritsu taiyo denchi no gijutsu kaihatsu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on analysis of super-high efficiency solar cells for practical use in fiscal 1994. (1) On the survey on crystalline compound solar cells, it was pointed out that the present study target is III-V compound semiconductor solar cell, and efficiencies of 36-39% are theoretically expected by use of two-junction cells. (2) On structure of super-high efficiency solar cells of 40%, selection of upper and lower cell materials for multi-junction cells, high-efficiency tandem Si solar cells, and the merit and possibility of light collection operation were surveyed, and their issues were discussed. (3) On physical properties of mixed crystalline semiconductors and characteristic evaluation of solar cells, impurities, trap center, minority carrier life, and applicability of supper lattice structure to high-efficiency solar cells were surveyed. (4) On fabrication technology of compound semiconductor solar cells, various problems of and approaches to electrode formation and antireflection film technologies, the meaning and issues of thin film substrate technology and continuous process, trial calculation of costs, safety, and resource problem were surveyed.

17th Business Report Meeting of New Energy Industrial Technology Development Organization (NEDO). Section Meeting on Solar Technology; Dai 17 kai jigyo hokokukai. Taiyo gijutsu bunkakai

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

In this section meeting, reports were made on the following themes: 1) outline of NEDO solar technology development; 2) commercialization study of thin film polycrystal solar cell production technology; 3) development of CdTe solar cell module production technology; 4) R and D of construction material monolithic solar cell modules; 5) development of the project overseas for solar energy technology development. In 1), outlined were the development of commercialization technology of photovoltaic power system, internationally joint demonstration development of photovoltaic power system, development of production facilities of solar cell use compound semiconductors, development of commercialization technology of solar system for industrial use, etc., and a large wind power system. In 2), the results of the study 'low cost Si substrate production by continuous cast method' were reported. In 3), the results were reported of the increase in efficiency and development of low cost production technology for large area modules. In 4), 3 kinds and 6 systems of R and D for house roofs and building walls were conducted, and possibilities of commercialization were obtained in terms of performance and economical efficiency as construction material. In 5), with the use of natural conditions and social systems in Nepal, Mongol, Thailand and Malaysia, the development for commercialization of this system is being made by joint research with each country. (NEDO)

Research and development of photovoltaic power system. Development of novel technologies for fabrication of high quality silicon thin films for solar cells; Taiyoko hatsuden system no kenkyu kaihatsu. Kohinshitsu silicon usumaku sakusei gijutsu

Energy Technology Data Exchange (ETDEWEB)

Shimizu, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

1994-12-01

Described herein are the results of the FY1994 research program for development of novel technologies for fabrication of high quality thin films of silicon for solar cells. The study on the mechanisms and effects of chemical annealing reveals that the film structure greatly varies depending on substrate temperature during the hydrotreatment process, based on the tests with substrate temperature, deposition of superthin film (T1) and hydrotreatment (T2) as the variable parameters. Chemical annealing at low temperature produces a high-quality a-Si:H film of low defect content. The study on fabrication of thin polycrystalline silicon films at low temperature observes on real time the process of deposition of the thin films on polycrystalline silicon substrates, where a natural oxide film is removed beforehand from the substrate. The results indicate that a thin polycrystalline silicon film of 100% crystallinity can be formed even on a polycrystalline silicon substrate by controlling starting gas composition and substrate temperature. The layer-by-layer method is used as the means for forming the seed crystals on a glass substrate, where deposition and hydrotreatment are repeated alternately, to produce the thin crystalline silicon films of high crystallinity. 3 figs.

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development is conducted for the acquisition of a system evaluation technique for predicting the performance of standard photovoltaic power systems and evaluation technologies applicable to residential photovoltaic power systems different from each other in terms of tilt and direction, district, solar cell type, etc. In fiscal 1999, using data collected from the Hamamatsu field test facilities and residential photovoltaic power systems installed across Japan, various design parameters, such as the irregularity compensation coefficient, temperature compensation coefficient, and the incidence compensation coefficient were determined, and, using the parameters as the secondary estimation values, design parameters were updated. In the development of simulation technologies, basic studies were made about the shadow compensation coefficient, spectral response fluctuation compensation coefficient, and the composition of polyhedral arrays. Moreover, studies were made about the estimation of large area insolation, based on the horizontal surface insolation data collected at 21 sites of residential photovoltaic power systems in the Kanto district. (NEDO)

Achievement report for fiscal 1997 on development of practical application technology for photovoltaic power generation systems. Development of technologies to manufacture thin film solar cells (development of technologies to manufacture silicon crystal based high-quality materials and substrates / survey and research on analysis of practical application); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu / silicon kesshokei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As a plan to develop technologies to manufacture materials and substrates for thin film solar cells, it is intended to reduce defect density, enhance film forming speed, largely improve the photo-electric conversion efficiency and increase manufacturing productivity. These goals will be realized by establishing methods to control defect density, crystal particle diameters and crystallization rate in silicon crystal systems. A technology to form micro-crystal silicon-based thin films will be developed, that have superior photo-stability, and are capable of realizing low cost and mass production. Discussions will be given on a high-density plasma control technology, a fundamental property evaluation technology for micro crystal silicon thin films, and a device design simulation technology. A technology will be developed to form amorphous silicon layer on a stainless steel substrate by using the plasma CVD process. At the same time, discussions will be given on optical annealing and thermal annealing as reformation methods. Fiscal 1997 has surveyed component technologies to identify and analyze quickly and accurately the technical trends inside and outside the country, and to mass produce thin film solar cells. The Material and Substrate System Technology Subcommittee (silicon crystals) was held to deliberate the four-year development program and its progress. (NEDO)

Report on evaluation concerning R and D of magneto hydrodynamic (MHD) generation. Introduction; Denji ryutai (MHD) hatsuden no kenkyu kaihatsu ni kansuru hyoka hokokusho. Soron

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

Evaluation was conducted concerning R and D on magneto hydrodynamic (MHD) generation, with proposals made for the future R and D. As a result of the experimental operation and studies of the Mark 7 machine for MHD generation, a cold wall type generation channel was found promising in the long-term durability under MHD generation conditions. In addition, R and D was conducted on the exhaust gas control system that fulfilled an environmental standard, seed recovery method, grasp of seed coagulation state, etc. The R and D on element technologies were carried out along with the R and D of the Mark 7 and played a role in the backup of its experiment. MHD generation presents a large number of attractive characteristics, with its development expected in the future. However, it seems too early to immediately move on to the next step. Examinations should be made on such matters as comparisons with various kinds of new power generation systems using coal, trends in foreign countries particularly the U-500 project of the Soviet Union, the ideal system for more efficient development, and possibility of international cooperation. (NEDO)

Model experiments on imaging subsurface fracture permeability by pulsed Doppler borehole televiewer; Pulse doppler borehole televiewer ni yoru kiretsu tosuisei hyoka ni kansuru model jikken

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Y; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

1996-05-01

This paper reports model experiments to evaluate flow rates of fluids passing through a fracture by using a Doppler borehole televiewer (DBHTV). A supersonic transducer disposed on a well axis transmits transmission pulses, and a transducer receives scattered waves generated by particulates in water and waves reflected on a well wall. This signal is applied with time gating to extract only the scattered waves from particulates in the vicinity of the well wall. Deriving spectra in the recorded Doppler signal obtains flow velocity components in the direction of the well radius. A model was made with a polyvinylchloride pipe with a diameter of 14.6 cm to simulate a well, to which an aluminum pipe with an inner diameter of 2 mm is connected to be used as a simulated fracture, and mud water is circulated in the pipe. The result of deriving a passed flow volume in this model by integrating flow rate distribution derived by using the above method to a predetermined range in the vicinity of the fracture showed a good proportional relationship with actual flow rate in the simulated fracture. 1 ref., 7 figs.

Evaluation of wind noise in passenger car compartment in consideration of auditory masking and sound localization; Chokaku masking to hoko chikaku wo koryoshita kazekirion hyoka

Energy Technology Data Exchange (ETDEWEB)

Hoshino, H. [Toyota Central Research and Development Labs., Inc., Aichi (Japan); Kato, H. [Toyota Motor Corp., Aichi (Japan)

1998-05-01

Discussed is a method for evaluating wind noise in passenger car compartment based on human auditory characteristics. In the study, noise in the compartment of a passenger car travelling at a constant speed is collected by use of a dummy head, and the collected noise is analyzed in view of the masking effect, directional sensation produced by binaural hearing, etc. A masked spectrum of noise in the compartment of a 6-cylinder vehicle travelling at 120km/h is analyzed, and it is found that some frequency bands, especially the band centering on 300Hz, are masked by a loud noise component falling in a low frequency band of 180Hz or lower. By use of masked spectrum analysis, the level of noise that is actually audible to human ears can be calculated. The noise level thus determined by masked spectrum analysis and the noise direction determined by a binaural signal processing model are examined, and then it is found that the noise direction is clearly determined when the noise belongs in a 450Hz band or higher where wind noise prevails. On the bases of the above-mentioned results and the directional sensation produced by binaural hearing, a `binaural wind noise evaluation method` is compiled. 20 refs., 9 figs., 1 tab.

Fiscal 1999 geothermal energy development promotion survey. Report on resource assessment for Shiramizugoe area; 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Shiramizugoe chiiki shigen hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Under an assumed plan of building a geothermal power station in the Shiramizugoe area of Makizono-cho, Aira-gun, Kagoshima Prefecture, investigations will be conducted under a 4-year program into the amount of geothermal resources, the dimensions and cost performance of a geothermal power station under consideration, and the environmental impact that the locating of such will incur, through for example identifying areas containing geothermal reservoirs suitable for geothermal power generation. In fiscal 1999, activities were conducted in the three fields of (1) survey plan preparation, (2) comprehensive analysis, and (3) environmental assessment. Under item (1), a survey and coordination implementation plan was prepared, existing data were analyzed for the construction of geothermal models out of which a suitable geothermal structure was specified for digging, and a list was drafted of locations for borehole digging for fiscal 2000. Under item (2), it was found that most of the past surveys covered the Ogiri area and that the Shiramizugoe area was but poorly covered. Discussion was made on the geological structure, geothermal structure, geothermal water hydraulic structure, and the geothermal water system. Under item (3), the plan was summarily explained to the local administration, associations of hot spring hotels, and inhabitants in the vicinity, and their consent was obtained. (NEDO)

Evaluation of flux-trapping and magneto-resistibility of superconductors by ESR spectroscopy; ESR ho ni yoru chodendotai no jisoku hosoku to taijiba tokusei no hyoka

Energy Technology Data Exchange (ETDEWEB)

Kusumori, T; Matsuura, K; Muto, H [National Industrial Research Institute of Nagoya, Nagoya (Japan)

1995-09-28

The abnormal sisal, which was observed in the ESR measurement of superconductors, was confirmed to be a non-ESR (non resonant) signal, from an ESR experiment applying parallel and vertically polarized microwave fields and from the calculation of the ESR transition probabilities. The field modulation dependence of the spectra revealed that the signal was composed of two components. From the modulation-scheme analysis and a study of type I and II superconductors, two components were assigned to the microwave responses to magnetizations trapped in the crystalline portion and at intergranular Josephson junctions. The former B and the batter J components are observed in the first derivative and absorption a form, respectively, and their polarities differently behave for the field sweep reversal. Based on these results, we have improved an ESR spectrometer, which makes it possible to measure separately two kinds of magnetization and to study the trapping ability and quantum flux. 11 refs., 12 figs., 1 tab.

Evaluation of building envelopes from the viewpoint of capability of controlling thermal environment; Onnetsu kankyo chosei noryoku ni yoru kenchiku gaihi no hyoka no kokoromi

Energy Technology Data Exchange (ETDEWEB)

Umeda, K; Ono, S [Taisei Corp., Tokyo (Japan); Shukuya, M [Musashi Institute of Technology, Tokyo (Japan)

1996-10-27

The ability that architectural space improves the thermal environment in comparison with outdoor environment is called the `capability of controlling thermal environment.` As the value becomes higher, the indoor thermal environment is more improved. In this paper, the controlling capability of six building envelopes with different window systems was compared. The heat transfer in the wall and window system is approximated using a lumped mass model of heat capacity to obtain a heat balance equation and combined with the heat balance equation in indoor air for backward difference. The wall surface temperature and indoor air temperature in a calculation model are then calculated. A radiation absorption coefficient is used for mutual radiation on each wall. In the model, the adjoining room or first- and second-floor rooms were made the same in conditions as the model on the assumption that the one-side lighted office in an RC reference floor is in the non-illumination and non-airconditioning state. In summer, the controlling capability remarkably varies depending on the window system. For the window facing the south, the annual capability is more advanced than in other directions and the indoor thermal environment is improved on the average. 7 refs., 12 figs., 1 tab.

Evaluation report on research and development of an ultra-advanced processing system. Summary edition; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Gaiyohen

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-08-01

Research, development and evaluation were performed with an objective of establishing the basic processing technology and ultra-precision machining device technology utilizing large output excimer laser and high density ion beams. With regard to the large output excimer laser technology, the short wavelength excimer laser life extension technology has demonstrated ong-life operation of 1.02 times 10{sup 9} shots exceeding the final target at the initial laser output of 105 mJ/pulse. With respect to the high-density ion beam technology, the gas phase converged ion beam technology has achieved an ionic current density of 2.5 {mu}A/sr. and a beam current of 25 pA. Regarding the ultra-precision machining device technology, a large ultra-precision grinding machine of five shaft control type was developed as a final target demonstrating machine, which exhibited the shape accuracy of 0.7 {mu}m and surface roughness of 3.45nm. The surface roughness satisfied the final target. Other activities include studies on the ultra-advanced processing technology, measurement and evaluation technology, comprehensive tests, and practical application of the technologies, having derived respective achievements. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program survey and research. Research on solar energy systems (Meteorological survey); 1981 nendo taiyo energy system no kenkyu. Kisho chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-31

The basic national map on global solar radiation compiled in fiscal 1975-76 provides but inadequate information on the weather of Japan where weather distribution and geography are complicated. The amount of global solar radiation is estimated using data supplied from 838 local weather stations across Japan, and a plan is implemented of compiling detailed local maps. For the application of a formula for this estimation, however, difference between the two types of sunshine recorders in use is taken up, which are the Jordan type and the solar cell type. Values observed using the two types of sunshine recorders at 149 sites are compared and the difference is defined. Using hourly observation records of sunshine duration at 838 sites across Japan (covering 2 years), and taking into consideration the outlines worked out for terrain and things on the ground surface, monthly correction coefficients are determined for correcting geography-caused difference in sunshine duration records (for all sites). Since the nationwide deployment of local weather stations was completed barely in 1979, normal values have to be estimated based on data collected in a short period following 1979. For 151 weather offices whose normal values are already known, normalization factors are worked out for converting the values obtained in a specified year into normal values, and monthly maps are prepared. When a normalization factor is determined for a given local weather station, values recorded at that station for a specified year may be converted into normal values. (NEDO)

Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (photovoltaic power generation); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This report describes the fiscal 1976 research result on the technical and economical perspectives of various solar cells, high-efficiency solar cell and its evaluation technique, and a photovoltaic power generation system and its applications. On Si single-crystal slice solar cell, it was pointed out that cost reduction by automatic production process using no vacuum process is essential. On Si thin film solar cell, some problems to be solved for development of particle accelerating growth technique were pointed out. Study was also made on 2-6 group compound semiconductor solar cell, 3-5 group bulk crystal solar cell, 3-5 group thin film solar cell, solar collection solar cell, and raw polycrystal Si materials. On photovoltaic power generation systems, it was reconfirmed through reconsideration of power generation systems for every application that the photovoltaic power generation system for residences is promising. On medium- scale power generation systems, study was made on power load and system configuration in consideration of applications to electric railway, highway, and power source of isolated islands. (NEDO)

FY 1990 achievement report on the survey of possibility of introducing solar energy into buildings; 1990 nendo taiyo energy no kenchikubutsu eno donyu kanosei chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

This paper describes the achievements in fiscal 1990 on survey on possibility of introducing solar energy into buildings. Capacity of photovoltaic power generation facilities installed on an area of 1600 km{sup 2}, such as roofs of residential houses, schools and building may be calculated on a trial bases as 100 million kW at maximum. The capacity can replace 16% of the total demand and corresponds to 26.30 million kiloliters (9%) as converted to crude oil. If photovoltaic power generation is utilized on buildings of users, diversified technological criteria are required from the viewpoint of legislation covering wide range of architectural, electrical and disaster aspects. However, no direct and clear standards are available now, except for the electric power business law. What are urgently required are solar cell standardization, incentive subsidies, aging safety, institutions for electric power sale and purchase, and establishment of technological criteria. An utilization example survey revealed problems in array installation and size. Increased demand, mass production and cost reduction will create a favorable cycle. Introduction, proliferation, and acceleration under policies at public facilities which are expected of enlightenment and development into other areas will be the effective means for the purpose. (NEDO)

Fiscal 1994 research report. Demonstration test for establishing technology for peakload shaving with dispersed small residential PV systems (Evaluation of weatherability of house-use solar light electric power generating system equipment); 1994 nendo jutakuyo taiyoko hatsuden fuka heijunka gijutsu nado kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutakuyo taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Weatherability tests such as exposure to the atmosphere are conducted to collect and accumulate information on the degradation of house-use photovoltaic equipment expected to come into use in areas where weather conditions are hostile. Based on the thus collected data, analysis and evaluation are conducted about the mechanisms of corrosion and degradation for the establishment of designing and evaluating methods for maintaining weatherability. Since fiscal 1994 is the first year of the project, preparations are made for tests to be conducted. In carrying out research activities, a Weatherability Evaluation Committee for House-Use Solar Light Electric Power Generating System Equipment is organized, who discuss implementation of the project. Discussion is made on the shape and structural materials of the exposure rack. An aluminum alloy coated with a clear coating of alumite sulfate is selected, and a rack is built. Specifications of a sea salt particle collector are discussed, and preparations are made for arresting and quantifying sea salt particles under the Japanese Industrial Standard (JIS) dry gauze method and the International Organization for Standardization (ISO) wet candle method. Solar cell module initial characteristics are measured. (NEDO)

Report on results concerning development of supermetal technology (FY1999-2000). Development of evaluation technology for formability of super metal (development of evaluation technology for formability of recrystallized microstructured plate); Super metal no gijutsu kaihatsu seika hokokusho (1999 - 2000 nendo). Super metal no seikeisei hyoka gijutsu nado no kaihatsu (bisai saikesshotsububan no seikeisei hyoka gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In connection with the innovative manufacturing of large base materials having a mesoscopic grain structure by means of technologies for high deformation accumulation control, recovery/recrystallization control, etc., research was conducted on evaluation technology for various characteristics such as formability, with fiscal 2000 results compiled. For the purpose of evaluating average grain size from an optical microscopic photograph of structures, it was judged reasonable to determine the average cut piece length. A device introduced to this development project was a horizontal goniometer capable of ODF (crystallite orientation distribution function)/pole figure measurement, qualitative analysis, and residual stress measurement. With warm rolling performed by controlling both material temperature of 7475 based alloys and roll temperature, thermally stable micro sub-grain structures were obtained. As a result of ODF analysis of this warm-rolled material, it was found that a {beta} orientation group existed very sharply in the area from the sheet surface to the center planar part of the thickness. The grain refinement of 5083 based alloys using a warm rolling method was also successful, with its ODF analysis revealing that the accumulation of the {beta} orientation group was very high as in the 7475 based warm-rolled materials. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Research and development of solar cell evaluation system - Survey of research and development of solar cell evaluation system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Surveys and studies were conducted for establishing methods for evaluating solar cell performance and reliability. In the effort to develop basic technologies for the comprehensive evaluation of the performance of various types of solar cells and modules, an ultrahigh matching solar simulator and a large area solar simulator were built. The long-term exposure tests of solar cell modules kept on at 5 sites in Japan, 3 sites in Australia, and 1 site in Oman, and the databasing of the test data was planned. In the long-term evaluation of solar cell durability, investigations centered about module deterioration, where abnormal heat generation was observed, cause of increased resistance was inspected, and separation between the cell and the filler was examined. In the development of an accelerated photodegradation test method, it was found that the result of a light-dark cycle test with the ambient temperature varied agreed excellently with the results of outdoor exposure tests. It was consequently proved that the light-dark cycle test was a very promising candidate for an accelerated photodegradation test for a-Si solar cells. (NEDO)

Fiscal 1994 achievement report. Development of photovoltaic power generation system practicalization technology - Development of ultrahigh-efficiency solar cell technology (Development of new photoelectric conversion material technology - Research on future feasibility of wet-type solar cells); Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Chokokoritsu taiyo denchi no gijutsu kaihatsu (shinkoden henkan zairyo no gijutsu kaihatsu (shisshiki taiyo denchi no shoraiteki kanosei no chosa))

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

A survey is conducted of wet-type solar cells that may constitute an important field in solar chemistry. The wet type solar cell made known by Graetzel et al. in 1991 is a combination of ultrafine TiO{sub 2} grains and a sensitizing dye. The ultrafine grain surface structure enlarges the area of an electrode for the absorption of 46% of incident solar radiation of which 80% or more is converted into electric power. The fill factor at 520nm of a cell fabricated for an additional test turns out to be 40% against the 76% mentioned in technical literature, and the conversion efficiency 10%. The Titanyl sulfate is also tested because it is low in price as material for titanium oxide. Functional groups are experimentally introduced for the generation of bonds on the substrate to be effective in the injection of a sensitizing dye. A sensitizing dye with two carboxyl groups and two bipyridine rings as ligand is allowed to be supported by TiO{sub 2}. IR (infrared) spectrometry is performed, and then formation is found of ester-like bonds or chelate bonds due to the interaction of carboxyl groups and the substrate surface. This is enhanced by surface treatment. (NEDO)

Estimation of hydrogen bondings in coal utilizing FTir and differential scanning calorimetry (DSC); FTir to DSC wo mochiita sekitannai suiso ketsugo no teiryoteki hyoka no kokoromi

Energy Technology Data Exchange (ETDEWEB)

Mae, K.; Miura, K. [Kyoto University, Kyoto (Japan). Faculty of Engineering

1996-10-28

With an objective to know coal condensation structure which has influence on coal conversion reaction, an attempt was made on quantitative evaluation of hydrogen bonding in coal. Using as test samples the VDC made from Taiheiyo coal swollen by tetralin and vacuum-dried, and its pyrolyzed char, DSC measurement and Fourier transform infrared spectroscopy (FT) were performed. An FT spectrum comparison revealed that the VDC swollen at 220{degree}C has the hydrogen bonding relaxed partly from the original coal. However, since the change is in a huge coal molecular structure restraining space, it has stopped at relaxation of the bonding energy without causing separation as far as free radicals. On the other hand, the DSC curve shows that the VDC has slower endothermic velocity than the original coal. In other words, the difference in heat absorption amounts in both materials is equivalent to the difference of enthalpy ({Delta} H) of both materials, which corresponds to the relaxation of the hydrogen bonding. Therefore, the {Delta} H was related to wavenumber shift of the FT spectra (which corresponds to change in the hydrogen bonding condition). By using this relationship, a method for evaluating hydrogen bonding distribution was proposed from an O-H contracting vibration change that can be measured by using the FT spectra and a thermal change that can be measured by using the DSC. 3 refs., 7 figs.

Characterization of the various catalyst for solvent hydrogenation at 1t/d PSU; 1t/d PSU ni okeru kakushu yozai suisoka shokubai no seino hyoka

Energy Technology Data Exchange (ETDEWEB)

Kakebayashi, H.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Aihara, Y.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

1996-10-28

Performance of various catalysts for hydrogenation of recycle solvent was evaluated for the operation of NEDOL process 1 t/d process supporting unit (PSU). Distillate between 220 and 538{degree}C derived from the liquefaction of Tanito Harum coal was used as recycle solvent. Deactivation behaviors of catalysts were compared using a prediction equation of catalyst life, by which aromatic carbon index (fa) after hydrogenation can be determined from the fa of recycle oil before hydrogenation, reaction temperature, and total hydrogenation time. Total hydrogenation time satisfying the {Delta}fa, 0.05 before and after hydrogenation were 8,000, 4,000, and 2,000 hours for NiMo-based catalysts C, A, and B, respectively. Catalyst C showed the longest life. Used catalysts were also characterized. The catalyst C showed larger mean pore size than those of the others, which resulted in the longer life due to the delay of pore blockage. From measurements by XPS and EPMA, relative atomic concentration of carbon increased remarkably after the use for all of catalysts, which was considered to be due to the adhesion of hydrocarbons. Increase of metal atoms, such as Fe and Cr, was also observed due to the contamination of entrainment residues. Deactivation of catalysts was caused by the adhesion of hydrocarbons, and metallic compounds, such as Fe and Cr. 3 refs., 1 fig., 5 tabs.

Assessment of global environmental impacts by utilizing methodology of LCA on solar water heater for dwellings; LCA shuho ni yoru taiyonetsu onsuiki no kankyo fuka hyoka

Energy Technology Data Exchange (ETDEWEB)

Kamoshida, J [Shibaura Institute of Technology, Tokyo (Japan); Asai, S [Yazaki Corp., Tokyo (Japan)

1997-11-25

CO2 emission was quantified through the life cycle of a solar water heater to assess its environment impact. Although LCA (life cycle assessment) originally sums up I/O of all materials and energy through the whole life cycle of a product to examine environment impact, this assessment was carried out for only CO2. Calculation of CO2 emission assumed a natural circulating solar water heater of 200 l in effective hot water capacity, 2.78m{sup 2} in effective collecting area, and 0.5 in average annual collecting efficiency of total solar radiation, and an auxiliary city gas heat source for compensating insufficient heat quantity. The total CO2 emission in the life cycle of a solar water heater was obtained from an industrial association table assuming the life cycles of 10 and 20 years. CO2 emission was estimated to be 5407.1kg-CO2 and 10665.2kg-CO2 for 10 and 20 years, respectively. CO2 emission due to city gas was largest in the total CO2 emission in the life cycle. As a result, for reduction of CO2 emission due to a solar water heater, improvement of equipment efficiency was most important. 6 refs., 5 figs., 3 tabs.

Experimental analysis of the structure attenuation characteristics on engine noise by pseudo cylinder pressure excitation; Giji tonaiatsu kashin ni yoru engine kozo no soon tokusei hyoka

Energy Technology Data Exchange (ETDEWEB)

Ozawa, H; Nakada, T [Isuzu Advanced Engineering Center, Tokyo (Japan)

1997-10-01

The engine structure attenuation has been experimentally analyzed by the newly developed in-cylinder excitation system. It can reproduce the complete cylinder pressure in non-running engine conditions by adopting the hydraulic and the piezoelectric actuator. The structure attenuation measured in this system has a good coincidence with the ones measured in actually engine operating conditions, meanwhile the current method, which applied only high frequency components as the excitation pressure, was shown to have the unsatisfied agreement. As a result, the proposed system has been concluded to be very useful to estimate the engine noise characteristics in non-running conditions. 4 refs., 11 figs., 1 tab.

Ecological effects assessment of anionic surfactant on aquatic ecosystem using microcosm system; Microcosm wo mochiita in ion kaimen kasseizai no suiken seitaikei ni oyobosu eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Takamatsu, Y. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering; Kurihara, Y. [Ou Univ., Fukushima (Japan). Faculty of Engineering; Matsumura, M. [University of Tsukuba, Tsukuba (Japan). Institute of Applied Biochemical

1997-11-10

Microcosm system was applied to assess effect of anionic surfactant (LAS) on aquatic ecosystem. Anionic surfactant such as LAS was added to an flask microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer, comparing with that of an natural lake model ecosystem derived from natural lake water. In the flask microcosm system and the natural lake model ecosystem, biodegradation rates of LAS were almost same and NOECs (no observed effect concentration) of LAS were also below 1.5 mg{center_dot} l{sup -1}. It was found that flask microcosm test could provide precise ecological effect assessment of LAS on number of microorganisms because the system showed higher reproducibility and stability than natural take model ecosystem. It was suggested that flask microcosm test was useful ecological effect assessment method which can reflect natural aquatic ecosystem. 10 refs., 4 figs., 2 tabs.

Remote sensing data analysis for assessment of sea level change in Asia; Asia ni okeru kaisuijun hendo eikyo hyoka no tame no remote sensing gazo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Okubo, Y; Tanaka, A [Geological Survey of Japan, Tsukuba (Japan); Kaku, M [Bishimetal Exploration Co. Ltd., Tokyo (Japan)

1997-10-22

Remote sensing images include information of coastal land division, sea level change such as sedimentary environment and vegetation, and distribution of artificial structures. Past sea level changes and their causes can be regionally obtained by analyzing these data and by integrating them with information obtained from geological survey. In this study, causes and history of past sea level changes, formation mechanism of coastal topography, and past sea level change survey in Thailand have been reviewed. This paper describes an extraction method of the sea level change information in coastal districts by analyzing several actual remote sensing images. For understanding the current sea level rise, it is required to clarify the causes quantitatively among three causes of sea level changes, i.e., volumetric change of total ocean water on the earth, relative sea level change due to the crustal deformation, and change of irregularity of sea surface with ocean current. It is also required to compile maps in Asian or global scales. 13 refs., 6 figs.

Fiscal 1992 report on geothermal development promotion survey (Development of geothermal reservoir assessment technique); 1989 nendo chinetsu kaihatsu sokushin chosa (Chinetsu choryusou hyoka shuho kaihatsu hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Efforts were exerted in fiscal 1984-1992 to develop techniques for appropriately assessing a geothermal reservoir for its productivity for duly predicting the optimum scale of power generation to be provided thereby. In the development of simulators, geothermal reservoir simulators (SING-1, -2, -3) and a geothermal well 2-phase flow simulator (WENG) were developed. As for the treatment of fractures in a reservoir and of substances soluble in the hot water, the methods for dealing with them were improved and augmented. In a model field study in a Hokkaido forest, reservoir pressure continuous observation and monitoring, temperature logging and pressure logging for existing wells, and geothermal fluid chemical analysis were performed for reservoir analysis, in which both natural state simulation and history mapping excellently reproduced the temperature and pressure distributions. The temperature and pressure distributions in a natural state simulation, out of the results of an analysis of the Oguni district model field, Kumamoto Prefecture, agreed not only with those in the natural state but also with the pressure transition data in the observation well. (NEDO)

Development of research activity supporting system. 2. Evaluation of desktop video conferencing; Kenkyu katsudo shien system no kaihatsu. 2. Enkaku kijo uchiawase hoshiki no jitsuyosei hyoka

Energy Technology Data Exchange (ETDEWEB)

Tsutsumi, F.; Hishitani, J.; Matsui, S. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-03-01

Desktop video conferencing (DVC) system and its software were investigated. A test system was actually constructed. Based on the test results, its practical advantage and disadvantage were illustrated. The DVC system was constructed using general LAN, and operation experiments were conducted, as to research activity. From the interview with participants and analysis of conversation history, advantage and disadvantage of this system were clarified. Performance of the trial system was examined using practical LAN, to compare with the performance of commercial systems. When using LAN, the same problems were given. It was found that the DVC system can not substitute for the conventional real face to face meeting, but it is suitable for some communication styles, for example free participation meeting or collaboration based on the same objective, which has been hard up to this time. In addition, software was made as trial, by which reservation of meeting, announcement, and calling can be carried out. 26 refs., 6 figs., 5 tabs.

International cooperation project. Evaluation report on development of new oxidation and environment resistant materials for petroleum excavation; Sekiyu kussakuyo taisankasei taikankyosei shinzairyo no kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to enhance the environment and wear resisting performance of the bearing mechanism for petroleum excavation bits assuming use at a depth of 6,000 m, discussions were given on a cubic boron nitride based ultra-hard thin film and a Ti{sub x}M{sub 1-x}N based hard thin film as the new materials. This paper describes the evaluation report for the year 2000. It was found that the promising material is the Ti{sub x}M{sub 1-x}N. The practical applicability test would require a considerable amount of expense and insurance fee, while putting the material into practical use would take some more time. However, the achievements in developing this new material will allow the material to be applied to cutting tools used under the same onerous condition, and theoretical development would be possible on the consideration of the film properties, whereas further development may be expected in the future. An international joint study has performed evaluations on the environmental resistance and the characteristics of the film at the University of Toronto. These evaluations are effective in enhancing further the properties of the thin film in the future. Achievements have been accumulated steadily from starting the fundamental studies, and high level objectives have been achieved. Accurate identification has been made on the state of developing the parts for petroleum excavation bits, with the objectives set properly. Putting the bits into practical use will still require public assistance. (NEDO)

Evaluation report on research and development of 'the comprehensive water recycling and utilization systems'; 'Mizu sogo saisei riyo system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-08-01

This research and development project is aimed at treatment of sewage, industrial waste water and the like at lower cost for reutilization, while efficiently producing methane or the like by the systems annexed to the water treatment systems with high-concentration bio-reactor systems incorporating separation membranes. The waste water types studied to be treated by these systems include sewage discharged in large quantities and waste water containing oil/fat and protein (low-concentration waste water), and starch-, alcohol and paper/pulp-containing waste water, and excrements (medium-concentration waste water). The project has found the optimum systems, by adequately configuring the separation membrane modules, and combining dissolution of suspended solid with methane fermentation reactors for selective treatment of organic substances; improved efficiencies of removing organic substances and producing methane by fermentation, and realized reduction in quantities of discharged sludge; and thereby established the bases for the new waste water treatment techniques. The reactor systems developed for water treatment are those based on biological removal of nitrogen. They greatly reduce treatment time to produce treated water of high quality. For treatment of sludge, the techniques have been developed to convert sludge into oil. These results are well applicable to various areas, e.g., sewage treatment, and food and pulp industries. (NEDO)

Evaluation of performance for solar house with Trombe wall. Part 5; Trombe hekishiki solar house no hyoka kenkyu (nichisekisan Trombe heki kyuhonetsuryo yosoku senzu no teian)

Energy Technology Data Exchange (ETDEWEB)

Yoshida, N [Nishimatsu Construction Co. Ltd., Kanagawa (Japan); Nakajima, Y [Kogakuin University, Tokyo (Japan); Watanabe, T [Tokyo Electric Power Service Co. Ltd., Tokyo (Japan); Abe, H [Ministry of Construction, Tokyo (Japan); Yamaga, K [Mitsubishi Estate Co. Ltd., Tokyo (Japan)

1996-10-27

A regression equation that can calculate the daily accumulated absorption heat of Trombe Wall was given, and the performance estimated chart of Trombe Wall in which the daily unit effect of Trombe Wall can be visually recognized was proposed. The absorption heat was multivariate-analyzed by two variables of solar radiation of that day and the previous day. The data obtained from simulation was used for analysis. The absorption heat was analyzed using the meteorological data at eight spots (Sapporo, Sendai, Niigata, Tokyo, Shizuoka, Kochi, Fukushima, and Kagoshima). In this case, the result of multivariate analysis almost coincided with the simulation result. A chart that predicts the absorption heat of Trombe Wall in eight cities from the daily accumulated global solar radiation of that day and the previous day was then created as the performance estimated chart of Trombe Wall. As a result, the solar radiation of that day little influences the absorption heat when the Trombe Wall increases in thickness. Conversely, the solar radiation of the previous day significantly influences the absorption heat. In future, an equivalent heat loss coefficient will be calculated from the performance estimated chart. 2 refs., 16 figs., 2 tabs.

Evaluation report on research and development of high-speed computation system for technological use; Kagaku gijutsuyo kosoku keisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-08-01

The above-named project is an effort implemented under the large-scale industrial technology research and development system through the cooperation of industrial, academic, and governmental circles in the nine-year-long period beginning in fiscal 1981. The project aims to establish technologies required for putting to practical use a high-speed computation system capable of speedily dealing with huge technological problems which the computers available at the commencement of the project failed to solve. The goals set for new devices and comprehensive systems were sufficiently challenging in view of the technological level of those days, and are still at the highest level in the world. It is judged that the goals were set with reason and appropriateness. The liaison council for the implementation of the project is constituted of people of experience or academic standing, entrusted research and development activities, Ministry of International Trade and Industry bureaus concerned, and the Electrotechnical Laboratory of the same ministry. Discussion, coordination, and communication on concrete matters are under way between the constituent members, contributing to the enhancement of research and development. The liaison council activities are evaluated to be appropriate and effective. (NEDO)

Development of a user interface and evaluation of an ontology for menu-based retrieval; Soho menu ni tekishita interface no kaihatsu to yogo bunrui no hyoka

Energy Technology Data Exchange (ETDEWEB)

Ito, Y.; Shinohara, Y.

2000-06-01

We have proposed the 'complementary menu system' as an easy-to-build and easy-to-use menu system. It has two component menu systems, one is based on a word taxonomy and the other is based on the document structure (e.g., the table of contents of the target document). By the user's selection of an item on a menu, the positions and relevance of related items are shown on the other menu, which makes users easier to select proper menu items. We have also shown the combination of context-sensitive menus reduces user's errors of selection of menu items by several experiments. In this report, we investigate the choice of word taxonomies effective for novice users and the design of structure and interface of menus to reduce overlooked related items. 1. Comparative experiment among a complementary menu using a general-purpose word taxonomy used in a thesaurus and the ones using domain-specific taxonomies based on quick references used in the target document, shows that even novice users prefer domain-specific word taxonomies and exhibit higher performance in retrieval significantly. 2. Comparison between a domain-specific word taxonomy that arranges different categories in a line and another domain-specific word taxonomy which reorganizes the categories under one parent category, suggests users relatively prefer the latter taxonomy but the preference depends on the amount of user's domain specific knowledge. 3. Component menu system which has only one menu showing the whole taxonomic hierarchy with scrollbars on which the positions and relevance of related items are shown is effective to reduce the number of overlooked items. (author)

FY 1997 Report on New Sunshine Project. International co-operative projects (Australia-Japan solar energy technology cooperation, etc); 1997 nendo kokusai kyoryoku jigyo. Nichigonado taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Described herein are the progresses, memorandum concluded for the new project, NEDO/MUERI project activities, among others, for, e.g., Australia-Japan solar energy technology co-operative project. The photovoltaic cell outdoor exposure test project has been progressing as expected in Australia since FY 1996. The test data have been collected for one year and analyzed successively. The second information exchange workshop is scheduled in June 1998 in Sydney for the thin-film, polycrystalline photovoltaic cell manufacturing technologies. The new type photovoltaic cell long-term exposure test project has been started in FY 1997 as the new project in Oman. The weather conditions of the test site are very severe, very high both in temperature and humidity. The new type photovoltaic cell modules, centered by the amorphous silicon, will be exposure-tested in the severe atmospheres, to verify long-term reliability of the photovoltaic cells. A total of 5 types of the modules are to be exposure-tested; 3 types of 6 amorphous silicon cells, one type of 2 CdS/CdTe cells, and one type of 2 thin-film polycrystalline cells. (NEDO)

Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (solar heat power generation); 1974 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyonetsu hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

This report summarizes the fiscal 1974 research result on solar heat power generation. The following are promising as solar heat power plant sites in Japan: Large-scale sites such as the foot of volcanos, riverbed, railway site and road, medium-scale sites such as isolated island, saltpan site and industrial park, and small-scale sites such as factory site, factory roof floor, housing complex, warehouse and school. Based on the primary concept design of both curved reflector type and tower type 1,000kW class solar heat power plants, various requirements were clarified roughly. It was clarified that food, fiber and non-ferrous metal factories can cover 80-90% of their thermal energy requirements with high- temperature solar heat, while factories related to food and fiber can cover even nearly 100% of their electric power requirements with solar heat. Study was also made on specifications of a solar simulator as common use facility necessary for characteristic evaluation of equipment and materials for solar heat power generation systems. (NEDO)

Solar energy and ecosystem. ; Simulation system for the ecological system (Bios-3 as an example). Taiyo energy to ecosystem. ; Seitaikei mogi system (Bios-3 wo rei to shite)

Energy Technology Data Exchange (ETDEWEB)

Nitta, K [National Aerospace Laboratory, Tokyo (Japan)

1992-11-30

The present report gives inspectional opinions about the Bios-3 which is a Russian artificial ecological system and explains the simulation system for the ecological system. The Bios-3 installed in a semi-underground dome of Biophysics Research Institute, Krasnoyarsk is a stainless steel-made enclosed box which is 120m[sup 2] and 3m in total area and height, respectively. Such an internal volume is structurally divided into two botanical cultivation rooms, oxygen supply use chlorella cultivation room and living room where the human living experiment can be done without interruption during half a year. It is judged that the ecological environment can not sufficiently condition both the autotrophic substances which are plants and mosses, and hetrotrophic ones which are animals and microbes. As for the conditional control of ecological system, neither BS-II, USA nor Bios-3 can arbitrarily change the environmental condition. However by utilizing buffers, air blowers and other physico-chemical controllers, development must be done of a new simulator which can change the environment, and elucidate the correlation between the environment and biological beings. That simulator may play an important role also for preparing the IGBP's global model. 5 figs.

Solar energy and ecosystem. ; Landpavilion for the 21st century's food production system and biosphere BSII. Taiyo energy to ecosystem. ; Shokuryo seisan landpavilion to biosphere II

Energy Technology Data Exchange (ETDEWEB)

Takakura, S. (The University of Tokyo, Tokyo (Japan). Faculty of Agriculture)

1992-11-30

The present report introduces the pavilion for the 21st century's food production system exhibited in Walt Disney World, USA. That system in the future world is explained together with the Biosphere BSII. In the Landpavilion the theme of which is energy and transport, cultivation can be observed in a six-acre greenhouse under three different ecological environments which are tropical rain forest, desert and grassland. Originating in the above cultivation, Japan's lettuce cultivation experiment is being done on three-dimensional triangular panels in a botanical factory under the cooperative research with the NASA and USD. In a desert in Oracle, Ariz. for the BSII, eight male and female persons are living in five biomes and agricultural production/residential quarter prepared there. The object of research covers the closed ecological system of many animals and plants growing with human beings, and simultaneously, circulation of the other substances. Recent articles which are somehow critical of contents and reports of the above experiment are being blamed for adversely affecting the BS project, which is taken notice of with a worldwide concern. 7 refs., 3 figs.

Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (solar heat power generation); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyonetsu hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

Research was made on solar heat power generation following last fiscal year, as a part of solar energy utilization technologies. In this fiscal year, in particular, research was made on the following: selection of suitable sites for solar heat power plants in Japan, estimation of expected power supply, positioning of a solar heat power system among future power systems, operation policy of solar heat power systems, survey on suitable sites for the 1,000kW pilot power plant, operation characteristics of the small test plant, design of the 1,000kW pilot power plant, test methods and facilities for every element equipment of solar heat power systems, an environmental test method for mostly solar collectors, and the profitability of solar heat power systems. Optimum operation temperature levels were nearly 350 degrees C for distributed systems and nearly 400 degrees C for centralized ones. The distributed system is profitable in a unit capacity range less than 5-10MWe, while the centralized system is profitable in a range over 10MWe. Under some assumptions, the power cost of solar heat power systems was estimated to be 20-30yen/kWH. (NEDO)

Performance in cooling mode of a heat pump using panels with PV cells as the condenser; Taiyo denchitsuki panel wo gyoshukuki to shita heat pump no reibo unten

Energy Technology Data Exchange (ETDEWEB)

Kawamura, T; Ito, S; Miura, N [Kanagawa Institute of Technology, Kanagawa (Japan); Fujita, M [Chubu Electric Power Co. Inc., Nagoya (Japan)

1996-10-27

Comparison was made between heat pumps in cooling operation, one having two panels provided with solar cells, the second having an air-cooled heat exchanger alone, and the third having a series connection of a panel unit and air-cooled heat exchanger, all serving as condenser. The results are shown below. In the case of two-panel-unit condenser, there is a difference ({Delta}t) of 15{degree}C between the daytime free air temperature and condensing temperature but, with decreased insolation, free air temperature, and wind speed in the evening, the {Delta}t lowered to approximately 8{degree}C while the COP (coefficient of performance) increased from 2.4 to 3.3. On a cloudy day in summer, the two-panel-unit condenser had a {Delta}t of 13.9{degree}C and a COP of 3.1. In the case of the series-connection condenser, the {Delta}t was approximately 8{degree}C and the COP was 3.5. The COP of the two-panel-unit condenser was lower than that of the air-cooled heat exchanger by 9% at an insolation of 442W/m{sup 2} but it rose to 12% in the absence of insolation. The COP of the two-panel-unit condenser was higher than that of a one-panel-unit condenser by 17%. When an insulator plate was attached to the back of a panel, the {Delta}t increased but the COP decreased by 14%. In the case of the series-connection condenser, the COP increased by 6% in the absence of the insulator plate. 2 refs., 9 figs.

FY 1997 report on the study on the formation condition of hetero-structure of single-crystalline semiconductor thin films; 1997 nendo chosa hokokusho (tankessho no handotai usumaku hetero kozo no keisei joken ni kansuru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Since ion implantation causes material degradation by formation of crystalline defects, and hydrogen embrittlement deteriorates material strength, reduction of such defects has been positively studied. Study was made on a new active application of hydrogen separation into ion implantation defects. After H ion implantation of a proper depth into single-crystalline Si and SiC and successive annealing, single-crystalline films of sub-micron to several micron thick were obtained by hydrogen-induced delamination at the implantation depth due to hydrogen embrittlement in crystalline defects. The implantation depth is dependent on implantation energy. H atom forms (111) face defect through connection with dangling bond of crystalline defects. This crystal face defect forms a delamination plane through (100) face cleavage. This hydrogen embrittlement delamination by ion implantation is applicable to production of light-weight high-efficiency single-crystalline Si solar cells, and large single-crystalline SiC wafers as new resource saving process. 33 refs., 19 figs., 2 tabs.

Report on evaluation of research and development of resources recycling/reutilization systems. Phase 2; Shigen saisei riyo gijutsu system no kenkyu kaihatsu (dainiki) ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-08-01

Described herein are the final evaluation results obtained by the 7-year R and D project, beginning in the FY 1976, established by the national project system for developing the techniques for treating urban solid wastes. This project has developed a semi-wet type selective crushing/sorting unit for sorting the wastes, and established the elementary techniques for recycling the wastes into various products, e.g., compost, pulp, combustible gases, aggregates, methane gas, or fuel oil. Two types of total treating systems, in which these elementary techniques are integrated, have been developed; one is to recover materials and the other energy. They can comprehensively, efficiently treat the wastes, adapting themselves to various situations. Pyrolysis which discharges reduced quantities of flue gases is adopted. Waste water is treated, mainly by biological treatment which is supported by the conventional methods, e.g., coagulation and adsorption. The cost estimation results indicate that the total system developed by this project can compare favorably with the conventional incineration system under general conditions, at a capacity of 300 t/d or more, when taking into consideration the secondary effects brought by the recycling/reutilization. This system is commercially feasible, when it meets with local characteristics, e.g., garbage collecting systems, market values of recycled resources, treatment/disposal conditions, and natural and social environments. This project has sufficiently achieved the original objectives. (NEDO)

Evaluation report on the design of solid catalysts for saving energy in petrochemical industry; Sekiyu kagaku no tame no sho energy gata kotai shokubai sekkei hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The aim is to improve on hydrocarbon oxidation which is a difficult reaction (analogous to combustion and having potential for heat generation or explosion, with restrictions therefore imposed on reaction conditions) by use of a catalyst supporting porous membrane. The fiscal 1999-2000 results are stated. In this effort, the target reaction is promoted by a catalyst supported by a porous membrane while combustion is controlled by the said porous membrane that separates oxygen and hydrocarbon from each other. Such a design was not available since a catalyst supporting inorganic membrane withstanding so high a temperature was difficult to prepare. Recently, however, a porous membrane with its pores regulated to microstructural dimensions was developed. The activity of a Pd membrane catalyst is evaluated in view of the degree of oxidation of propylene, cyclohexene, and benzene. It is then found that hydrogen that has passed the Pd membrane participates in the reaction. In a propylene oxidation test using a membrane type Ag/Al{sub 2}O{sub 3} catalyst, it is found that acetone is generated and that oxygen after passing through the membrane participates in the reaction. Methods are studied for preparing a metal membrane in which the catalyst system comprises a catalyst supporting porous membrane and a Pd membrane. In the fabrication of metal membranes, a highly selective hydrogen permeable membrane is stably prepared by the thermal CVD (chemical vapor deposition) method. (NEDO)

Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

Energy Technology Data Exchange (ETDEWEB)

Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)

1996-10-28

An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

Leading research report for fiscal 1998. Life landscape performance evaluation technology (Landscape Frontier); 1998 nendo sendo chosa kenkyu hokokusho. Seikatsu keikan seino hyoka gijutsu (land scape frontier)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the formulation of guidelines for the construction of an appropriate landscape in the 21st century for the creation of 'landscape industry' in a sustainable society, researches were conducted for the development of landscape materials to constitute living circumstances equipped with 'life landscape' and of technologies for evaluating them. In the landscape designing system subcommittee, the current states and problems of landscape designing systems were analyzed and problems to solve were clarified, these problems involving systems and institutions, people and collaboration, formation of a consensus, systems for production and distribution, etc. In the landscape materials subcommittee, a 'landscape cell' concept in which a life space is the unit was employed in discussing the needs for landscape materials to meet and in extracting the seeds the industry was able to offer for improvement on landscape. In the landscape evaluation subcommittee, the history and today of landscape were reviewed to define what was to be respected in the development of evaluation techniques, and guidelines were extracted towards landscape materials development and landscape industry promotion. In addition, a Landscape Frontier symposium was held. (NEDO)

Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

Report on evaluation of research and development of light-aided instrumentation/control systems. Abstract; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Gaiyohen

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-08-01

This research and development project is aimed at commercialization of the light-aided instrumentation technology systems which safely, stably measure, transmit and control process information including image information, e.g., temperature, flow rates and components at large plants in industrial complexes, in the severe atmospheres in the presence of, e.g., electromagnetic induction and combustible gases. These optical systems need development of light transmitting/receiving devices, various optical devices that constitute the network nodes, and various types of sensors of improved functions and reliability, in addition to development of the techniques required for transmitting large quantities of information on a large scale. This project has attempted to systematically make break-through in the individual elementary techniques, in particular those in the widely diversified technological areas for the advanced devices, and thereby to expand the instrumentation/control technology frontiers. The results of studies on gallium/arsenic crystals, which are prerequisite for photoelectronic integrated circuits as the bases for the light application technology, and processes for producing thereof are highly rated worldwide. It is planned to effectively utilize the total system, constructed at then Nippon Mining's Mizushima Refinery, and thereby to establish the effective instrumentation techniques for commercial plants and to promote commercialization of these results. (NEDO)

Achievement report for fiscal 1998. Development of Assessment Technology of Life Cycle Environment Impacts of Products; 1998 nendo seika hokokusho. Seihinnado lilfecycle kankyo eikyo hyoka gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An inventory data collecting format is formulated, data collecting activities are launched through 23 industry associations and several investigatory agencies, and almost all the primary data are collected. All the inventory items are being rearranged into a convenient order, and efforts are under way to designate the association to be in charge and the method to be used for data collecting (the accumulation method, process model method). Problems about techniques in the veinous department are extracted. The flow of matters relating to various metals and glass after their use and the magnitude of their environmental impacts at the ultimate sites of treatment are understood though roughly. Investigations are conducted into typical formats overseas, a data arranging format is constructed, specifications are defined for a data inputting software program, and a request is placed with a dedicated dealer for the compilation of the said program. The architecture and specifications of an LCA (life cycle assessment) database system are determined, and its functions are undergoing an intermediate check by a research team for improvement. Endeavors are exerted at quantifying global warming, ozone layer depletion, biotoxicity, and photochemical oxidants for use as the basic data for damage evaluation. (NEDO)

Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

Low temperature formation of ferroelectric PbTiO3 films by laser ablation with 2nd laser irradiation; Reiki hikari laser heiyo laser ablation ho ni yoru kyoyudentai PbTiO3 usumaku no teion keisei

Energy Technology Data Exchange (ETDEWEB)

Tabata, H.; Kawai, T. [Osaka University, Osaka (Japan)

1997-08-20

The unique advantage of the pulsed laser deposition is its ability to produce highly oriented stoichiometric films at a low substrate temperature. Ferroelectric PbTiO3 thin films have been formed using 2nd laser assisted laser ablaion technique at low temperature, i.e., 350degC, on Sr7iO3 single-crystal substrates and Pt/MgO electrodes. The second laser irradiation at the substrate surface is quite effective for crystallization of the films at low substrate temperature below 400degC. The suitable energy density (fluence) of the irradiation laser is in the range of 30-100 mJ/cm{sup 2}. X-ray diffraction patterns of PbTiO3 thin films show c-axis orientation, with a rocking angle of 1.0 - 0.5deg. These films exhibit ferroelectric hysteresis loop. The dielectric constant and remanent polalyzation of the PbTiO3 films are in the range of 120-150 and 60-80 {mu}C/cm{sup 2}, respectively. 31 refs., 10 figs., 1 tab.

Solar energy and ecosystem. ; Japanized biosphere simulator (restructing of artificial ecosystem originating in the biosphere). Taiyo energy to ecosystem. ; Nipponban biosphere simulator (biosphere ni manabu jinkoteki ecosystem no kochiku)

Energy Technology Data Exchange (ETDEWEB)

Azuma, K. (Hazama Gumi, Ltd., Tokyo (Japan))

1992-11-30

The present report introduces Japanized biosphere (BS) simulator which was structured in order for the BS research committee composed of people of experience or academic standing and related industrials to elucidate the CO2 circulation behavior in the biological sphere of temperate zone. Its principal structural factors were ocean, grassland and broad-leaved tree forest, while river and lake were assumed to be those for the water circulation. Animals and plants which were necessary for the ecological system were taken as biological elements, while the installed system technology facilities covered the air, water, lighting, monitoring and energy. Those facilities are 40000m[sup 2], 60m and 2400000m[sup 3] in total area, height and volume, respectively on the site expanding to a scale of 20ha. Apart, land and ocean were arranged on the ground expanding to 2000000m[sup 2]. The quantification of different circulating substances is being studied, while the material balance is controlled so as to totally result in zero. Nobody can enter the facilities because of simplification in experimental model. The meteorological condition is monitored. The structuring was done by taking the biological sphere of BS-II Project, USA as an object. As the basic survey has been generally completed, an investigation team is on the point of being organized. 2 figs., 1 tab.

Solid electrolyte membranes and the system to produce hydrogen from thermally decomposed water by solar energy; Taiyo energy riyo ni yoru mizu no chokusetsu netsubunkai kara no suiso seizoyo

Energy Technology Data Exchange (ETDEWEB)

Nigara, K; Watanabe, K; Kawamura, K; Kawada, T; Mizusaki, J; Ishigame, M [Tohoku University, Sendai (Japan). Research Institute for Scientific Measurements

1996-10-27

For conversion of solar heat to transportable energy, hydrogen production by direct thermal decomposition of water using concentrated high-temperature solar heat was studied. Water vapor is injected into the tubular target with high melting point and high oxygen permeability at high temperature while heating the target by concentrated solar heat over 2000K. Oxygen in decomposed gas is discharged through an oxygen permeable membrane to extract hydrogen. Solid electrolyte is used as one of the target materials. Oxygen gas in the high-oxygen partial pressure site changes into oxygen ion by accepting two electrons at the target surface, and returns to neutral oxygen gas in the low-oxygen partial pressure site by discharging two electrons at the surface after permeation through oxygen vacancy. In the case of n-type solid electrolyte, to obtain constant permeation of a large amount of oxygen, flow of a large amount of electrons is indispensable in the opposite direction to oxygen ion. Among [(ZrO2)(1-x)(CeO2)x](0.9)(CaO)(0.1), materials of 0.4-0.5 in x seems to be useful as the target material. 7 refs., 7 figs.

Studies of flat-plate solar air collectors with absorber plates made of amorphous silicon photovoltaic modules; Amorphous taiyo denchi module wo shunetsuban to shita heibangata kukishiki shunetsuki no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sato, K; Ito, S; Miura, N [Kanagawa Institute of Technology, Kanagawa (Japan)

1996-10-27

A light/heat hybrid air type heat collector has been developed in which heat is collected by solar cell panels. In Type 1 heat collector provided with a glass cover, two modules are connected in series and placed under a glass cover to serve as a heat collecting plate, each module built of a steel plate and two thin-film amorphous solar cells bonded to the steel plate. Air runs under the heat collecting plate. Type 2 heat collector is a Type 1 heat collector minus the glass cover. Air is taken in by a fan, runs in a vinyl chloride tube, and then through the heat collector where it is heated by the sun, and goes out at the exit. Heat collecting performance was subjected to theoretical analysis. This heat collector approximated in point of heat collection a model using a board painted black, which means that the new type functions effectively as an air-type heat collector. Operating as a photovoltaic power generator, the covered type generated approximately 20% less than the uncovered type under 800W/m{sup 2} insolation conditions. Type 1 has been in service for five months, and Type 2 for 2 months. At present, both are free of troubles such as deformation and the amorphous solar cell modules have deteriorated but a little. 4 refs., 9 figs.

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the solar cell evaluation system; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka gijutsu no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was made of the development of the basic technology for the integrated evaluation of solar cell performance, grasp of degradation phenomena of solar cell modules by outdoor exposure test, development of the accelerated degradation test method, etc., and the FY 2000 results were summed up. As to the development of the ultra-high approximation solar simulator for cell evaluation, a simulator was fabricated of which the irradiation non-uniformity is {+-} 1.0% and the spectral agreement is within {+-} 10% in 10 wavebands out of the 16 wavebands. Relating to the development of evaluation technology of large area modules, performance of the spectral irradiance distribution, etc. was improved by modification of the solar simulator, which made accurate measurement possible. In the study of degradation of solar cell modules, exposure tests on various kinds of solar cell modules were continued at 5 sites in Japan, 3 sites in Australia and 1 site in Oman for data collection/analysis. Further, analysis was made of Isc changes in the early stage of exposure, phenomenon of cell's cloudy discoloration, degradation caused by increase in series resistance, etc. As the test method of light accelerated degradation of A-Si solar cell, a brightness cycle test method was developed. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the solar cell evaluation system; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka gijutsu no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was made of the development of the basic technology for the integrated evaluation of solar cell performance, grasp of degradation phenomena of solar cell modules by outdoor exposure test, development of the accelerated degradation test method, etc., and the FY 2000 results were summed up. As to the development of the ultra-high approximation solar simulator for cell evaluation, a simulator was fabricated of which the irradiation non-uniformity is {+-} 1.0% and the spectral agreement is within {+-} 10% in 10 wavebands out of the 16 wavebands. Relating to the development of evaluation technology of large area modules, performance of the spectral irradiance distribution, etc. was improved by modification of the solar simulator, which made accurate measurement possible. In the study of degradation of solar cell modules, exposure tests on various kinds of solar cell modules were continued at 5 sites in Japan, 3 sites in Australia and 1 site in Oman for data collection/analysis. Further, analysis was made of Isc changes in the early stage of exposure, phenomenon of cell's cloudy discoloration, degradation caused by increase in series resistance, etc. As the test method of light accelerated degradation of A-Si solar cell, a brightness cycle test method was developed. (NEDO)

Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Discussions and evaluations have been performed on the safety and durability of the device installed with inverter to protect grid connection being an important device in the photovoltaic power generation system. This paper summarizes the achievements in fiscal 1996. The current fiscal year performed data collection and long-term continuous operation according to the durability test program for the device installed with inverter to protect grid connection, as the continuation from the previous fiscal year. In the electrical characteristics, although no large changes have been found in AC overvoltage and AC undervoltage, instability was observed in the detection level. With regard to temperatures in different components, the temperature rise has become nearly the same as in the maximum output continuous operation as a result of the repetition of the operation and shutdown, whereas the influence on the electrical and thermal stresses have increased. Particularly, when temperature rise in the AC side noise filter was given observation, the measurement of conductive high-frequency terminal voltage showed a value higher by several ten dB than in the previous fiscal year. The current fiscal year has gone farther to starting the measurement of noise electric field intensity as the base of electromagnetic interference. (NEDO)

Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Discussions and evaluations have been performed on the safety and durability of the device installed with inverter to protect grid connection being an important device in the photovoltaic power generation system. In discussing the durability test items, electrical property changes were observed on AC overvoltage, AC undervoltage, frequency rise, and frequency fall, as the continuation from the previous fiscal year, in order to evaluate temperature rise in different parts due to lapse of operation time and the effects of thermal stress in each component on the stress of the entire product. Furthermore, verification of single operation detecting function, tests on sudden input power change, sudden grid voltage change, and measurement of conductive high frequency terminal voltage were conducted in addition to the above observations. In discussing the durability test methods, repetition of operation and shutdown during the rated operation was adopted in place of the simulated operation using variation in the insolation having been discussed in the previous year. As a result of the tests, no noticeable changes were recognized from the evaluation result after a lapse of 5,000 hours from the start of the operation, as compared to those after the aging operation. (NEDO)

Research report for fiscal 1997 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1997 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Tests and discussions have been performed on the safety and durability of the device installed with inverter to protect grid connection, being an important device in the photovoltaic power generation system. The particularly important requirements demanded in the device were specified as maintenance of electric power quality, coordination with the protection system in the grid side, and assurance of safety of personnel and facilities. The current fiscal year has performed operation corresponding to that in the actual field for 20 years in total, and the evaluation tests on electrical characteristics and electric power quality. This paper summarizes the achievements in four years including the results available up to the previous fiscal year. Although no large change has been identified in the electrical characteristics, variance has been found in the detection time of overvoltage in the grid side. With regard to the electric power quality, the value has exceeded 89 dB as the determining condition for the certification test in the conduction interfering waves of 5 kHz to 10 kHz. In addition, it was confirmed that the conductive high-frequency noise terminal voltage in the grid side after the repetition of operations and shutdowns tends to increase according to the operation lapse time. (NEDO)

Achievement report for fiscal 1981 on the development of solar energy technologies for the development of practical application technologies for photovoltaic power systems. Experimental fabrication of solar cell panels and verification thereof (Development of technologies for panel assembly process); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (panel kumitate kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In a study of cell array connection process, continuous and automatic connection of cells is named as the basic concept in view of low cost and high reliability. In the designing of details of cell strings, CZ (Czochralski) cell dimensions are reviewed for cell packaging efficiency improvement, interconnectors and wiring are examined for a easier packaging process, and solder connection is thought over for utility cost reduction. Conditions are established for string fabrication process details. In the study of the panel packaging process, panel package designing is carried out and a dedicated mechanical device is installed. In the study of the inspection process and plant system, data are collected, necessary for the construction and adjustment of an inspection device. Research is conducted on the layout of plant facilities, on required utilities, and on facilities operating state signals to be transmitted to the central control unit. As for an inspection jig supply system, transfer system, and storage rack, they are designed, built, and installed. The plant house is now complete. (NEDO)

Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects. Solar energy technology research and development; solar panel experiment, manufacture, and verification (Photovoltaic power system practical application technology; ribbon-type crystal substrate process technology); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (ribon kessho kiban kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Carried over from the preceding fiscal year are the development of ribbon crystal pulling technology and the studies of ribbon crystal substrate quality and plant operation. In the development of ribbon crystal pulling process, a pulling drive is built and the limiter mechanism is strengthened for improvement on ribbon crystal flatness, technologies are established for high-speed pulling of broad ribbon crystals, pulling system prototype is built, after-annealing technique is improved for eliminating distortion, and technologies are developed for continuous feeding of raw materials. In the quality examination of ribbon crystal substrates, a method is tested and studied for bringing about a decrease in the number of SiC grains. The object of the plant operation study is a plant capable of producing 250kW-equivalent ribbon crystals a year, and the efforts involve the ribbon pulling system, rough cutter, real-size cutter, etching unit, shape checker, packing, devices for production lines such as warehouses for products, electric power, gas, water, peripheral equipment for waste water treatment etc., ribbon specifications check, quality related assistance equipment to deal with unacceptable products etc., pollution-preventing facilities for the preservation of production environments, and plant buildings. (NEDO)

Achievement report for fiscal 2000 on development of technology to evaluate reliability of petroleum refining facilities; 2000 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper reports the achievements in fiscal 2000 in development of a technology to evaluate reliability of petroleum refining facilities. The development efforts were made mainly on analyses by simulation and neural net (NN) that utilize computers. In the high-temperature system facilities, the creep damage generation is governed by different factors including impurities. The evaluation on joint life requires simultaneous use of low temperature zone long-time test. Verification was made on application of non-destructive inspection, such as use of ultrasonic waves in the accelerated creep zone. Defect detecting capability was identified when an ultrasonic wave flaw detection model is used for buried piping. In the pulse eddy current flaw detection, a coil most superb in totality was selected by means of simulation, by which corrosion and wall thickness of piping and devices were detected from outside the sheathing materials. Development was made on a technology to diagnose and evaluate corrosion of tank in operation by using the AE method. The remaining life of transformers is determined by how seriously the coil insulating paper has been deteriorated, and furfural in the oil was found effective for the parameters. Particularly, application of the NN was revealed to be effective in estimating electric motor deterioration. A high-temperature sulfide corrosion rate estimating model was developed from the operation and measurement data of the facilities by applying the NN and TCBM. (NEDO)

Evaluation stationariness of triaxial seismic while drilling and detection of reflected wave; Kosei kussaku ni tomonau danseiha no sanjiku kaiseki ni yoru hiteijo hyoka to hanshaha no kenshutsu

Energy Technology Data Exchange (ETDEWEB)

Yoshida, T; Asanuma, H; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

1996-05-01

This paper reports a method to detect reflected wave components contained in an elastic wave caused in association with well drilling. Measurement was made on an elastic wave caused in association with well drilling in an experimental field by using a triaxial elastic wave detector disposed in a measurement well. Analyzing the particle motion tracks in the derived elastic wave signals (to derive the main axial direction of a three-dimensional hologram) revealed that oscillation direction of the signals changes non-steadily by time centering around the S-wave oscillation direction. In addition, a sound source position was estimated during the drilling. Existence probability of the S-wave signal in the non-steady continuous signals was estimated by handling the particle motion tracks stochastically. In addition, this existence probability was used as a weighting function for a correlative analysis to detect a reflected wave from directly reaching wave components in the non-steady continuous signals. Thus, improvement in reliability of reflected wave detection was attempted. Effectiveness of this method was endorsed by the field data. 3 refs., 7 figs.

Fiscal 2000 research report on the study on management program for comprehensive assessment of chemical materials; 2000 nendo kagaku busshitsu sogo hyoka kanri program ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the realization of environmentally friendly, sound economic activities and the assurance of a safe and peaceful daily life for people, studies were conducted about comprehensive risk assessment and management techniques to use in dealing with chemical substances. Concerning the above-named management program, a workshop was called, where panel discussion and exchange of views and opinions were held. In the study of overseas technological trends, visits were paid to interested institutes and corporations in Denmark, Sweden, and Germany, where hearings were held over the management and manufacture of chemical substances. Concerning the control of chemical substances, surveys were conducted of the control in Japan and abroad and of the methods that businesses and other organizations followed in meeting the control. It was found that the control was being dealt with earnestly in every country and that chemical substances would stay managed under international collaborative conditions. Efforts were being positively exerted by businesses and other organizations to properly manage and reduce chemical substances and to develop and use substitutes. It was found that measures for handling chemical substances were closely knit into business management. (NEDO)

Research, development, and evaluation of basic technologies for next-generation industries. Technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu hyoka. Saibo tairyo baiyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

The project aims to establish basic technologies for the mass culture of cells by utilizing the features of animal cells, which will enable a large, stable supply of fine chemicals such as highly functional physiologically active proteins whose industrial production the conventional technique of synthesis fails to realize. For this purpose, efforts are exerted to select cells which are capable of producing target substances, to breed highly productive strains, to develop a serumless medium that satisfies demands for an all-purpose feature and heat sterilization, and to develop technologies of high-density culture and effective refining, etc. Some DNA (deoxyribonucleic acid) recombination technologies are also resorted to. As the result, a high-density culture of 2 times 10{sup 8} cells/ml has become available. Production is now feasible of various differentiation-inducing elements such as monoclonal antibodies with anti-HB virus activity, DIF, etc. Furthermore, cooperation with the Tsukuba University leads to the discovery of a novel vasopressor peptide (endothelin). The heat sterilization accepting serumless medium, which is put to practical use as the first of the kind in the world under this research and development project, contributes to the advancement of basic studies about cell biology. (NEDO)

Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

FY 1977 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Heat-storage subsystems); 1977 nendo taiyo energy riyo system chosa kenkyu. Chikunetsu sub system

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at surveys and researches on materials for heat-storage systems for solar thermal power generation systems and solar energy systems for air conditioning and hot water supply; analysis of current status of heat-storage subsystems and extraction of problems involved therein; and sorting out the research themes. Surveyed are the tower type light-collecting systems under development for solar thermal power generation systems, heat-storage subsystems with flat- and curved-surface type light-collecting systems; heat-storage systems being developed by the Electrotechnical Laboratory; heat-storage materials for solar thermal power generation techniques; regenerative heat exchangers; thermodynamic considerations for heat storage and molten salt techniques; and relationship between heat storage material properties and containers. Problems involved in each item are also extracted. The heat-storage subsystems for solar energy systems for air conditioning and hot water supply are now being under development, some being already commercialized, and the classification of and surveys on the related techniques are conducted. At the same time, problems involved in the heat-storage subsystems, being developed for residential buildings, condominiums and large-size buildings, are also extracted. The research themes for the heat-storage subsystems for solar air conditioning and hot water supply systems are sorted out, and case studies are conducted, based on the discussions on, e.g., thermal properties of heat-storage materials, behavior and heat transfer characteristics of latent heat type heat-storage materials, and corrosion of the heat-storage materials. (NEDO)

Characterization on impact damage resistance of CF/PEEK laminates under low and high velocity impact tests; Teisoku/kosoku shogeki shiken ni yoru CF/PEEK no taishogeki sonshosei no hyoka

Energy Technology Data Exchange (ETDEWEB)

Morita, H; Hamamoto, A [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Adachi, T; Nishimori, K; Matsumoto, H [Tokyo Institute of Technology, Tokyo (Japan)

1995-04-15

Experiments were conducted to learn the impact damage on jet engine CFRP components for sucking birds or others. A great mass low velocity collision experiment using a falling weight and a small mass high velocity collision experiment using an air gun were conducted. The damages inflicted upon CF/PEEK (polyetheretherketone) laminates in the respective experiments were compared with each other by using the ultrasonic flaw detection method (C-Scan). There was a linear relationship in both experiments between the projected damaged area DA measured by C-Scan and the impact energy IE, enabling the relative evaluation of impact-withstanding damage characteristics by using the DA/IE ratios. DA/IE in the high velocity impact was higher than that in the low velocity impact, but the DA/IE ratio between the high velocity impact and the low velocity impact remained approximately the same, not dependent on the fiber orientation. The lamination parameter {beta} defined on the basis of the difference in-plane rigidity between the layers constituting the laminate is proportional to DA/IE, with {beta} enabling the generalized numerical expression of the impact of the fiber orientation upon the impact-withstanding damage characteristics. 9 refs., 5 figs., 2 tabs.

1998 Annual Study Report. Standardization of corrosion resistance testing/evaluation methods for coated steel sheets; 1998 nendo seika hokokusho. Hyomen shori koban no taishokusei shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to develop the evaluation methods for reappearing corrosion characteristics of coated steel sheets in a short time, acid rain composition and artificial acid rain composition for the accelerated test were studied, and the cyclic corrosion tests were conducted. The literature survey shows that the main ionic species present in acid rain are Ca{sup 2+}, Mg{sup 2+}, Na{sup +}, K{sup +}, NH{sub 4}{sup +}, SO{sub 4}{sup 2-}, NO{sub 3}{sup -}, and Cl{sup -}, of which the acid rain components are SO{sub 4}{sup 2-} and NO{sub 3}{sup -}, their equivalent ratio (NO{sub 3}{sup -}/ SO{sub 4}{sup 2-}) in the Far Eastern area being 0.2 to 0.3. Therefore, the solution specified by ASTM 1141 is diluted 30 times with water to prepare the base solution for the accelerated tests, where its acidity is adjusted with a mixed acid of NO{sub 3}{sup -}/ SO{sub 4}{sup 2-} = 0.2 to 0.3 (pH: 3.0 to 4.0). Two sets of preliminary cyclic corrosion tests were conducted, one involving acid rain spraying, drying and humidification in this order, and the other acid rain spraying, humidification and drying. Analysis of the test data indicates that difference between these test cycles in corrosion rate is within a deviation range caused by different testing tools. Therefore, the former condition is adopted as the basis for the accelerated tests, because of its smaller deviation caused by different testing tools. (NEDO)

Non-contact estimation of the bond quality in soldered thin laminate by laser generated lamb waves; Laser reiki ramuha ni yoru handazuke sekisohaku no setsugo seijo no hisesshoku hyoka

Energy Technology Data Exchange (ETDEWEB)

Kasama, H.; Futatsugi, T.; Cho, H.; Takemoto, M. [Aoyama-Gakuin University, Tokyo (Japan). Faculty of Science and Engineering

1998-03-20

The bond quality of a solder-bonded copper laminated plate was modeled into rigid contact (rc) and slip contact (sc) to calculate the velocity dispersion of lamb waves. The velocity dispersion of laser generated lamb waves was measured, and the bond quality or the thickness of a solder layer was evaluated by non-contact. In the model whose bond surface is rc, the velocity dispersion of lamb waves can be calculated under conditions where the stress and displacement in an interface are continuous. In the model whose bond surface is sc, it can be calculated under conditions where an interface slips freely. Weak bond indicates the velocity dispersion between rc and sc. In this model, the velocity dispersion can also be calculated by a change in the thickness of a solder layer and used for quantitative evaluation of a bond interface. A three-layer solder bond manufactured for trial could be evaluated from the velocity dispersion of laser lamb waves. At the room temperature, the change in bond quality near the solder melting point of bond laminate that was judged as rc was investigated. When the solidus temperature is exceeded, the amplitude of lamb waves and the velocity dispersion changed largely. The amplitude of lamb waves increases as the liquid phase ratio increases. The bond quality near the solder melting point can be evaluated using lamb waves. 9 refs., 10 figs., 2 tabs.

1998 Annual Study Report. Standardization of methods for evaluating properties of new glass at high temperature; 1998 nendo seika hokokusho. New glass koon bussei no hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

High-temperature properties of glass melts, e.g., density, volume expansion coefficient, surface tension, viscosity, specific heat, thermal and electrical conductivity, redox equilibrium and gas solubility, are basic factors that must be considered in high quality glass melting technology and computer simulation of the glass tank furnace. The structure of the glass melts is also important for understanding these properties. This R and D program is aimed at proposing the international standards for the methods of measuring these high-temperature properties of the melts. The 1988 efforts are directed to the measuring technologies for density, volume expansion coefficient, surface tension, viscosity, specific heat, thermal and electrical conductivity, redox equilibrium, gas solubility and melt structures of soda-lime-silica glass melts. The R and D for measuring methods for high-temperature melts through international cooperation and establishment of the international standards for these methods are proposed in the joint CGR/HVG/TNO/GPF conference, which provides the arena for information exchange by glass manufacturers. (NEDO)

Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

Report on results 1998. Standardization of test measuring method of fine ceramics for communication equipment; 1998 nendo seika hokokusho. Tsushin kikiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Technological development is in progress at present for the intelligent transport system for example that uses a microwave frequency range of 60GHz or 90GHz toward the practical use, with a demand increasing for measuring the electrical properties of fine ceramics (FC) to be used in the communication equipment of the system. The measuring method in the microwave frequency range of 30GHz or less is about to be standardized in IEC TC49/WG10; however, the method above 30GHz has not yet been examined for the standardization internationally. The subject research is intended to establish the method of measuring electrical properties such as the dielectric constant of FC for a high-frequency/ultra high-frequency wave range, dielectric loss and surface resistivity, to standardize the principle of their measuring methods, measuring tools, adjusting method of samples, procedures of measurement, etc., and to aim at the international standardization. This year, investigation and examination were carried out on various measuring methods including overseas examinations in the U.S., extracting the Fabry-Perot resonator method and a conductive cylindrical dielectric cavity resonator perturbation method for example, and evaluating the specifications of standard reference materials. In addition, a morphological technique was established for measuring sample surfaces affecting measurements, by means of an accurate measuring instrument for thin film surfaces. (NEDO)

Life cycle assessment for spray coatings applied to the heating tubes of PFBC boiler; Kaatsu ryudoso boiler sonai kan e tekiyosareru yosha coating no life cycle assessment (LCA hyoka)

Energy Technology Data Exchange (ETDEWEB)

Sonoya, K; Kihara, S [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

1996-12-25

LCA (Life cycle assessment) is a systematic process used to calculate and evaluate the environmental impacts of products. Because boiler components are now exposed a more severe erosion/corrosion environment by, improving efficiency of thermal power plant, it is expected that the use of thermal spray coatings will increase. The LCA method was attempted to apply to various thermal spray coatings for PFBC (Pressurized Fluidized Bed Combustion) and evaluate the eco-friendly, coatings. The result was gained that all the alumina coatings have good characteristics. In fact the Al2O3-40%ZrO2 coating by APS has the lowest environmental impact and the best erosion resistance, it may be considered the most effective coating. 4 refs., 12 figs., 1 tab.

Toxicity assessment of organochlorine compounds detected in water environment using cultured human cell lines; Hito yurai saibo baiyokei wo mochiita suikankyo shiryochu no yuki enso kagobutsu no dokusei hyoka

Energy Technology Data Exchange (ETDEWEB)

Kunimoto, M; Yonemoto, J; Soma, Y; Nakasugi, O [National Institute for Environmental Studies, Tsukuba (Japan)

1997-11-10

As part of validation processes of in vitro toxicity assays for the risk assessment of environmental hazards, we applied an in vitro toxicity test using two human cell lines, neuroblastoma NB-1 cells and glioblastoma U-87 MG cells, to the assessment of organochlorine compounds detected in the water environment. The in vitro toxicity assay using NB-1 cells was calibrated by testing reference chemicals proposed by MEIC (Multicenter Evaluation of In Vitro Cytotoxicity), an international program for the validation of in vitro cytotoxicity assays. Beforehand, an assay using cells in frozen stock without subcultivation was examined by comparing IC50 values with the ordinary assay using subcultured cells. IC50 values for MEIC reference chemicals from the former assay showed good correlation with those from the latter assay, suggesting that the assay using cells in frozen stock can be used at least for the assessment of basal cytotoxicity. IC50 values for ten organochlorine compounds frequently detected in the sediment samples from contaminated rivers, p-chloroaniline, 3,4-dichloroaniline, p-dichlorobenzene, o-dichlorobenzene, Tris (2-chloroethyl)-phosphate, 2,5-dichlorophenol, 2,5-dichloroanisol, Triclosan and Triclocarban, were obtained with the in vitro assays and compared with their LD50 values in rats. No significant correlation, however, was seen between the IC50 and LD50 values, indicating that further improvement of in vitro toxicity assays is necessary for the application to the risk assessment of environmental hazards. 7 refs., 4 figs., 1 tab.

Evaluation report on research and development of an ultra-advanced processing system. Sections 1 and 2; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. 1 and 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-08-01

The ultra-advanced processing system is intended to develop an ultra-advanced processing device technology and an ultra-advanced processing technology. These technologies are indispensable to create such new processing technologies as ultra-precision and ultra-micro processing, and ultra high-grade surface modification processing, which have been impossible by the processing technologies having been available to date. It is also intended to develop a measuring and evaluating technology to support the above technologies. The intended system makes it possible to produce 21st century electronic components and ultra-high grade environment resistant materials. In order to achieve these goals, research and development has been performed on the excited beam technologies such as large output excimer laser and high-density ion beams, the ultra-precision machining device technology, the ultra-advanced processing technology using the above technologies, and the measuring and evaluating technology to assure the reliability of these technologies as the fundamental technologies. This project has begun in fiscal 1986, where fiscal 1987 has achieved development of component technologies related to the large output excimer laser and high-density ion beams, the ultra-precision machining device technology, the ultra-advanced processing technology using the above technologies, and the measuring and evaluating technology, and completed the device technology, having achieved the final target. (NEDO)

Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

Accomplishments hitherto achieved regarding the development of solar cell manufacturing technologies and the future course. Annex; Taiyo denchi seizo gijutsu kaihatsu no koremade no seika to kongo no hoko. Fuzoku shiryo

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-07-01

Collected in this paper are the results of evaluation and studies which were conducted, regarding the development of solar cell manufacturing technologies, by the Solar Cell Manufacture Evaluation Sub-Committee at its 4 meetings held in the period from May to August, 1985. For the development of technologies of manufacturing solar cells under the Sunshine Program, the development of technologies for manufacturing crystalline solar cells and amorphous solar cells is required. The Industrial Technology Council, Ministry of International Trade and Industry, in August, 1982, set intermediate goals to be achieved by fiscal 1985. To be developed for the practical application of crystalline silicon solar cells are a low cost experimental silicon refining system and an experimental solar panel manufacturing system. To be carried out for amorphous solar cells are basic studies including a study of physical properties, the development of a large-area high-efficiency solar cell manufacturing technology, and the development of a low cost monosilane manufacturing technology making use of molten salt electrolysis in a closed cycle. In fiscal 1984, 90% of the goals were attained, and now it is expected that almost all will be complete within fiscal 1985. (NEDO)

FY 1977 Annual report on Sunshine Project results. Research on solar energy systems for air conditioning and hot water supply; 1977 nendo taiyo netsu reidanbo kyuto system no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at research and development of utilization of solar energy for air conditioning and hot water supply, as part of the researches on systems under Sunshine Project for utilization of solar energy. This project is focused on the research items, selected from those pursued by the 3-year project beginning in FY1974 as the ones considered to be important for the future diffusion and promotion of the systems for utilization of solar energy. The 3-year project has produced the software and hardware results, based on development of the devices and construction of a solar house. At this stage of time, it is pointed out that studies on economic viability of the system, development of the software for diffusion of the solar systems, and development of new, more suitable systems and methods for utilization of solar energy are important. In this fiscal year, the four themes (studies on economic viability of the conceptual solar system designs, simplified methods for designing the systems, evaluation of system performance, and studies on energy-saving effects and economic viability) are taken up, viewed from development of the software for diffusion and promotion of the systems for utilizing solar energy, based on the results obtained by the previous 3-year project. (NEDO)

FY 1998 annual report on the solar energy technology research and development working group. 19th R and D activity report; 1998 nendo taiyo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by the solar energy R and D working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, gave a lecture titled (Expectation on and problems involved in power generation by solar light and wind power), and Mr. Kamon, a managing researcher of NEDO's solar technology development group, reported (Technological development trends of solar technology development group). The other topics reported by the individual groups include development of large-size wind power generation systems, development of techniques for increasing throughputs of high-efficiency, large-area amorphous solar cells, development of techniques for manufacturing high-reliability CdTe solar cell modules, development of techniques for manufacturing CIS solar cell modules, analysis/assessment of thin-film silicon-based solar cells, development of processes for manufacturing silicon of rationalized energy use, R and D of (new multi-layer structure) modules assembled into building materials to form monolithic structures, and development of techniques for manufacturing amorphous thin-film polycrystalline silicon hybrid thin- film solar cells. (NEDO)

Reports on 1979 result of Sunshine Project. Investigation and research on solar energy utilization system (solar thermal power generation system); 1979 nendo taiyo energy riyo system chosa kenkyu. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

In connection with the practicability of a solar thermal power generation system, examination was made on the technical economic problems and the operation method as well as on the problems of required performance of the constituent equipment, with the measuring method and performance evaluation method examined that are suitable for various devices. The items for the examination are as follows: (1) Silicon as the raw material for solar cells and its R and D, (2) Amorphous silicon solar cells, (3) R and D on low cost solar cells and array, (4) Basic design for photovoltaic generation system, and (5) Problems and technical subjects for solar cell standard measurement. The research themes and items for the above examination are listed as below: (1) Demand trend for raw material silicon, overseas trend, and development plan for polycrystalline silicon; (2) R and D plan for amorphous Si solar cell and its system, their optimum design, and their cost analysis and economic effect; (3) Technological investigation on cells and examination on array; (4) Basic design, peripheral equipment for system, and development schedule; (5) Report on the first actual state investigation concerning instrumentation of solar cells, i.e., on 'instrumentation and deviation in transformation efficiency', calibration system, problems of instrumentation of new device, problems of reliability test method, situation in various countries, and trend in atmospheric turbidimeter. (NEDO)

Design and construction of radiant panel for cooling and heating with photovoltaic and thermoelectric element modules; Taiyo denchi to netsuden soshi module wo mochiita fukusha reidanbo panel no sekkei oyobi shisaku

Energy Technology Data Exchange (ETDEWEB)

Sato, M; Tani, T [Science University of Tokyo, Tokyo (Japan); Kadotani, K; Imaizumi, H [Komatsu Ltd., Tokyo (Japan)

1997-11-25

Utilizing cooling properties and current voltage characteristics of a small cooling panel using thermoelectric elements which had been fabricated previously on a trial basis, design and prototype production were executed on a large radiant cooling and heating panel driven by photovoltaic cell modules. The panel design set the cooling area to about 0.5 m {sup 2} and the number of elements to 70 pieces, and optimum number of elements in series and parallel connection was derived. As a result of the analysis, it was made clear that the optimum number of thermoelectric module arrays in series and parallel connection varies depending on insolation intensity. It was found preferable that the number of parallel connection array be set to one to two in a region or time period in which low insolation intensity is distributed in greater amount. In the case where high insolation intensity is distributed in a greater amount, setting it to two to three is preferable. By using the structured design method and the HASP Tokyo data, thermoelectric element modules were interconnected with 35 modules in series and two in parallel on a cooling panel installed on the roof of the Science University of Tokyo. A simulation result revealed that the average temperature difference on the cooled surface in summer is 4.37 degC, and the solar cell utilization rate is 0.67. It is necessary in the future to improve heat dissipation efficiency and area ratio. 1 ref., 12 figs., 5 tabs.

FY 1998 annual report on the solar energy technology research and development working group. 19th R and D activity report; 1998 nendo taiyo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by the solar energy R and D working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, gave a lecture titled (Expectation on and problems involved in power generation by solar light and wind power), and Mr. Kamon, a managing researcher of NEDO's solar technology development group, reported (Technological development trends of solar technology development group). The other topics reported by the individual groups include development of large-size wind power generation systems, development of techniques for increasing throughputs of high-efficiency, large-area amorphous solar cells, development of techniques for manufacturing high-reliability CdTe solar cell modules, development of techniques for manufacturing CIS solar cell modules, analysis/assessment of thin-film silicon-based solar cells, development of processes for manufacturing silicon of rationalized energy use, R and D of (new multi-layer structure) modules assembled into building materials to form monolithic structures, and development of techniques for manufacturing amorphous thin-film polycrystalline silicon hybrid thin- film solar cells. (NEDO)

Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

Reports on 1979 result of Sunshine Project. Investigation and research on solar energy utilization system (solar thermal power generation system); 1979 nendo taiyo energy riyo system chosa kenkyu. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

In connection with the practicability of a solar thermal power generation system, examination was made on the technical economic problems and the operation method as well as on the problems of required performance of the constituent equipment, with the measuring method and performance evaluation method examined that are suitable for various devices. The items for the examination are as follows: (1) Silicon as the raw material for solar cells and its R and D, (2) Amorphous silicon solar cells, (3) R and D on low cost solar cells and array, (4) Basic design for photovoltaic generation system, and (5) Problems and technical subjects for solar cell standard measurement. The research themes and items for the above examination are listed as below: (1) Demand trend for raw material silicon, overseas trend, and development plan for polycrystalline silicon; (2) R and D plan for amorphous Si solar cell and its system, their optimum design, and their cost analysis and economic effect; (3) Technological investigation on cells and examination on array; (4) Basic design, peripheral equipment for system, and development schedule; (5) Report on the first actual state investigation concerning instrumentation of solar cells, i.e., on 'instrumentation and deviation in transformation efficiency', calibration system, problems of instrumentation of new device, problems of reliability test method, situation in various countries, and trend in atmospheric turbidimeter. (NEDO)

Research and development of system to utilize photovoltaic energy. Study on large-scale PV power supply system; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyo energy kyokyu system no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on large-scale PV power supply systems in fiscal 1994. (1) On optimization of large-scale systems, the conceptual design of the model system was carried out which supposes a large-scale integrated PV power generation system in desert area. As a result, a pair of 250kW generation system was designed as minimum one consisting power unit. Its frame and construction method were designed considering weather conditions in the inland of China. (2) On optimization of large-scale transmission systems, as large-scale power transmission systems for PV power generation, the following were studied: AC aerial transmission, DC aerial transmission, superconducting transmission, hydrogen gas pipeline, and LH2 tanker transport. (3) On the influence of large-scale systems, it was estimated that emission control is expected by substituting PV power generation for coal fired power generation, the negative influence on natural environment cannot be supposed, and the favorable economic effect is expected as influence on social environment. 4 tabs.

Study on the optimal control of the ground thermal storage system in the greenhouse. Part 4; Onshitsu ni okeru taiyo energy dochu chikunetsu system ni okeru saiteki seigyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Zheng, M [Sanko Air Conditioning Co. Ltd., Osaka (Japan); Nakahara, N [Kanagawa University, Yokohama (Japan)

1996-10-27

Three types of weight in both energy saving and optimum room temperature environment were changed to obtain the optimal control solution of the ground thermal storage system in a greenhouse. The relation diagram between the optimal solution of a performance function, and the state constraints and control function constraints was created in consideration of the energy term in a control function value area and the room temperature environment. As a result, the whole image of the performance function could be grasped in consideration of the energy term with inequality constraints and the room temperature environmental term in this study. The rate of a weighting factor in the performance function significantly influences the optimal solution. The influence on the optimal solution also changes when the optimal room temperature schedule differs. The influence that three types of rising algorithm exert on the convergence and converging speed was investigated. Superiority or inferiority occurs according to the space properties of a performance function. A zigzag method is most disadvantageous. The constraints can be converged to the optimal solution using an SUMT outer point method irrespective of the initial value. 6 refs., 6 figs., 4 tabs.

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the system evaluation technology; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on the evaluation method for the performance prediction system of the standard photovoltaic power system, the R and D were conducted of the system generation output prediction technology which is general-purpose, simplified and applicable to various kinds of photovoltaic power system for residential use, and the FY 2000 results were summed up. In this fiscal year, the photovoltaic power system for residential use was increasingly installed at 15 places, and 100 sites in total were made database and analyzed. As to the development of simulation technology, technology of calculation was established such as the simulation of multi-plane array composition and correction of multi-plane array incidence. Further, technical information on system trouble and knowledge/information/proposal for reducing power generation loss were arranged by design parameter. Using the data on solar radiation/power loss at sites of residential use photovoltaic power systems installed in the Kanto area, value analysis of the capacity of wide area facilities of the photovoltaic power system was made by the statistical method. This study was compiled into the revised edition of design manual. (NEDO)

Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure, with the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system. This paper summarizes the achievements in fiscal 1995. In the outdoor exposure test on solar cell modules, multi-crystalline silicon solar cell modules were selected as the test specimens, and thermo-couples were embedded in the modules to measure the temperatures. Also for the purpose of comparison, storage test specimens were stored in a constant temperature and humidity chamber. The exposure tests were carried out in three locations of the city of Choshi in Chiba Prefecture, the Miyako Island test site in Okinawa Prefecture, and the Miyako Island seashore. In the measurement and evaluation, appearance observation and measurements of output characteristics and insulation resistance were executed in summer and winter. No noticeable changes were observed in the measurements after lapse of four months and six months. In the outdoor exposure tests of metal test pieces, aluminum alloys were tested for corrosion caused by contact with different kinds of metals. Although the test period was short in the current fiscal year, difference in corrosion degrees in the aluminum alloys was found already in three months. (NEDO)

Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure, with the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system. This paper summarizes the achievements in fiscal 1996. In the outdoor exposure tests on solar cell modules, results of the tests were derived for up to 18 months after the start of the exposure at Choshi City, Miyako Island and the Miyako Island seashore. In the appearance observation, some white rust has appeared in the contact section of the aluminum frames of the solar cell modules and fixing screws, which have been exposed at Miyako Island and the Miyako Island seashore, but no changes that may give influence on the performance of the solar cells have been observed. The results showed performance similar to or slightly inferior to that before the exposure as a whole. The insulation resistances were all found good. According to the result of the outdoor exposure test of metal test pieces, noticeable difference in the corrosion degrees was recognized in the contact corrosion section of the aluminum alloys exposed in three areas having different meteorological and environmental factors. Electroplated zinc was found to have severer pitting corrosion in the contact sections than treatment-free zinc. (NEDO)

Research report for fiscal 1997 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1997 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system, weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure. This paper summarizes the achievements in fiscal 1997. In the outdoor exposure tests on multi-crystalline silicon solar cell modules at Choshi City, Miyako Island and the Miyako Island seashore, the output characteristics after the exposure tests showed a result that the insolation intensity and the change in the short circuit current are approximately proportional, and the temperature in the module and the change in the open voltage are inversely proportional. The module characteristics retention rate showed no change in the 29-month exposure at all of the three exposure locations. The insulation resistance in the exposure test specimens have been good at 2,000 M{omega} or more in all the locations until 18 months have elapsed. However, the test specimens in Miyako Island and the Miyako Island seashore showed 99 M{omega} after 23 months, and 129 to 1,774 M{omega} after 29 months. According to the outdoor exposure tests of metal test pieces, noticeable difference was found in corrosion due to difference in the environment by each exposure location, whose order of the corrosion degree was the Miyako Island seashore > Miyako Island > Choshi City. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology - Photovoltaic system data book, separate volume); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu bessatsu (taiyoko hatsuden system data shu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the research and development of photovoltaic power generation system evaluation technology, great progress has been achieved in performance improvement and cost reduction as far as constituent devices such as power modules and inverters are concerned. In the designing of systems, however, quantitative elucidation of loss and power reduction factors remains insufficient. Under the circumstances, several types of photovoltaic power generation systems expected to be put to practical application in the future are taken up, test facilities are constructed which simulate them, and data are collected. The thus-collected data are utilized for research and development of evaluation techniques necessary for the improvement of photovoltaic system efficiency, such as design parameter quantification, databasing and utilization thereof, and simulation technologies, for the establishment of technologies for optimum designs and optimum operations. The data book accommodates data, arranged in an easy-to-use fashion, collected about verification test facility (interconnected systems, independent systems, and water pump systems) operation, weather conditions, and residential photovoltaic power generation systems. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research on practical application of set solar cell); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shisshiki taiyo denchi jitsuyoka kanosei chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Possibility of practical application of dye-sensitized solar cells (Graezel cells) is discussed. Fine titania particle preparation conditions and titania thin-film electrodes were optimized and an energy conversion efficiency of 7.7% was accomplished. The screen printing method was applied to the manufacture of dye-sensitized electrodes, and performance governing factors were grasped. The use of the screen printing method resulted in a conversion efficiency of 6-8.4% when the factors were optimized. Though lower than the 10% in the Graezel report, values near that were obtained. The status of latest research and development is compiled involving studies about electron transfer dynamics in dye-sensitized solar cells, manufacture of sensitizing dyes and mesoscopic metal oxide thin-film, electron transfer layers and their physical properties, and solidification of hole transfer layers. Research was conducted aiming at their practical application, and tasks and problems in each of the said items were point out. A logical approach to achieve high conversion efficiency was deliberated, and studies were made about how to propel forward endeavors involving design guidelines for high-performance sensitizing dyes, design and preparation guidelines for thin film for electrodes, analysis of stability, solidification of the redox electrolyte, etc. (NEDO)

Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-01

Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

Report on evaluation on endocrine disturbing effect of chemicals and development of test methods; 1999 nendo kagaku busshitsu no naibunpi kakuran koka ni kansuru hyoka oyobi shikenho no kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With regard to endocrine disturbing effect being the new deleteriousness of chemicals, data were collected and evaluated by using the existing testing methods, data were collected by using the screening test, the testing methods were developed, and international investigation was carried out to establish the risk evaluation methods. In the evaluation by using the existing test methods, seven substance groups deficient in deleteriousness data qualitatively and quantitatively were given reproduction toxicity tests to evaluate availability of the endocrine activity. Development of the screening test method has been carried out by participating the validation test by OECD to make the uterotrophic assay method and the Hershberger assay method a test guideline having international matching property. International investigations to establish the risk evaluation were executed on the molecular mechanism of nuclear receptors, the chemical, metabolic and environmental behaviors of endocrine active substances, the effects of the endocrine active substances on experimental animals and human, the utilization thereof for risk assessment in human, and the effects of endocrine disturbance acting substances in wildlife species. (NEDO)

Seismic risk assessment of building based on damaged database of 1995 Hyogoken Nanbu Earthquake; Hyogoken nanbu jishin no hisai database wo mochiita kenchikubutsu no jishin risk hyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suwa, H.; Nobata, A.; Seki, M. [Obayashi Corp., Tokyo (Japan)

2000-01-10

The objective of this paper is to evaluate a vulnerability function and a repair cost in terms of each structural damage level based on the damaged database of the 1995 Hyogoken Nanbu Earthquake. The seismic risk of a building in Kobe is calculated through the analytical results. As a result, the following are verified : 1. The expectation of vulnerability function, in which peak ground acceleration is taken for seismic intensity, is about 550 cm/s{sup 2} for minor damage, about 700 cm/s{sup 2} for moderate damage, and about 950 cm/s{sup 2} for major damage respectively. However, the coefficient of variation (C. O. V. ) is about 0.5 for all damage levels. 2. The expectation of repair cost per square meter is about 29000 yen for minor damage, about 60000 yen for moderate damage, and about 64000 yen for major damage respectively. However, the variation is very large, for example, the C. O. V. for repair cost varies from 1.2 to 1.6. 3. The seismic risk of a building in Kobe, that is normalized by new construction cost, is about three percent on condition that the design lifetime is assumed to be 50 years. (author)

1998 Annual Study Report. Standards development of chemical analysis and non destructive inspection methods for pure titanium metals; 1998 nendo seika hokokusho. Jun chitan no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This study was conducted to standardize the chemical analysis and non-destructive inspection methods for pure titanium metals of industrial grade. These methods are among those serving bases for international standardization of products. The chemical analysis is aimed at quantitative analysis of trace impurities, in particular, present in pure titanium metals of industrial grade by developing and standardizing the inductively coupled plasma atomic emission spectroscopy, known for its low detectable limit, and, at the same time, spark and glow discharged atomic emission spectrometry as the improved routine analysis methods. These methods, although being used by, e.g., steel makers, have not been standardized because the effects of titanium-peculiar matrix are not elucidated. The non-destructive testing is aimed at standardization of the techniques useful for automatic production lines. More concretely, these include optical methods aided by a laser or CCD camera for plate surface defect inspection, ultrasonic methods for plate internal defect inspection, and pressure differential methods for air-tightness of welded pipes. They have not been used yet for automatic production lines. (NEDO)

Investigational study of evaluation of the global energy system as a global environmental protection technology; Chikyu kankyo taisaku gijutsu toshite no global energy system no hyoka ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

With relation to some global energy systems of which viability is predicted in the future, an evaluation was conducted from the viewpoints of economical efficiency, energy balance, CO2 emission, etc. The fossil fuel CO2 capture system, the conventional thermal power plant added with CO2 recovery/treatment facilities, is expected to reduce approximately 70-75% of the CO2 emission. The fossil fuel decarbonated hydrogen system, which decarbonates fossil fuels, recovers/treats CO2 at the place of fuel supply and uses as hydrogen, is of poor practical application from an economical point of view. The fossil fuel methanol synthesis system, which synthesizes methanol from fossil fuels at the place of fuel supply, generates electric power and recovers/treats CO2 with the methanol, is large in energy loss and CO2 emission and low in overall efficiency and CO2 reduction effect at the time of methanol synthesis. The renewable energy hydrogen system is an ultimate system with no emission of CO2, though it costs much. 110 refs., 83 figs., 107 tabs.

Estimation of water-coal surface interaction during heat treatment of coal by use of FTir and DSC; FTir to DSC wo mochiita sekitan-mizu kan sogo sayo no teiryoteki hyoka

Energy Technology Data Exchange (ETDEWEB)

Miura, K.; Mae, K.; Morozumi, F.; Kusakawa, T. [Kyoto University, Kyoto (Japan)

1997-10-30

The authors have recently presented a method to estimate the strength distribution of hydrogen bondings in coal using FTir and DSC. The method was applied to estimate the strength of coal-water interaction in two different coals and to estimate the enthalpy change deriving from the change in hydrogen bondings during the desorption of water. The estimated enthalpy change was compared with the total enthalpy change estimated by DSC measurement to examine the importance of hydrogen bondings during the desertion of water. 1 ref., 6 figs.

Study of numerical simulations concerning the performance of antennas used for automobile wireless communications; Jidosha no musen tsushin ni okeru antenna seino hyoka no tame no suchi simulation no ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Sueyoshi, M; Yano, T; Noda, Y; Goto, H [Honda Lock Mfg. Co. Ltd., Tokyo (Japan)

1997-10-01

Automobiles and communication technologies will be more closely related with each other in the advanced intelligence society. Anti-theft security systems apply those technologies, where antenna performance is one of the key elements. This is a study of numerical simulations of the performance of those vehicle antennas. 2 refs., 2 figs.

Research and development of system to utilize photovoltaic energy. Survey on the evaluation of photovoltaic power generation; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoko hatsuden hyoka no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on evaluation of PV power generation in fiscal 1994. (1) On the evaluation technique of energy pay-back time, foreign trial calculation examples by integration method were surveyed. However, there were not many study examples, and the calculation basis of input energy was also ambiguous. The calculation result by input-output analysis in Japan gave the value more than that by integration method, pointing out that indirect input energy is essential. (2) On the evaluation technique of the degree of environmental contribution, CO2 emission of the PV generation system installed on ordinary housing roofs was calculated to estimate reduction of CO2 emission and cost. As a result, PV power generation as reduction measures against CO2 brought a little cost increase. (3) On the latent scale of PV power generation, it was estimated to be nearly 191GW although under no restriction. It was a considerably large value as compared with the current power generation capacity in Japan. 4 tabs.

Output characteristic of photovoltaic module on different installing conditions. Comparison with calculated value and measured value; Secchi joken no kotonaru taiyo denchi module no shutsuryoku tokusei. Suchi kaiseki to jissokuchi tono hikaku

Energy Technology Data Exchange (ETDEWEB)

Sasaki, T.; Morita, Y.; Iwawaki, H.; Fujisawa, T.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

1997-11-25

The paper studied output characteristics of photovoltaic modules different in installation conditions on the basis of the energy balance state. In the study, an energy balance equation was constructed for insolation intensity, heat losses from PV surface/back, and output, in order to calculate cell temperatures in each installation condition. A comparative study was made between calculated results and measured data obtained on the top of the school building. The results indicated the following: The thickness of thermal boundary layer became approximately 27mm at insolation intensity of 800 W/m{sup 2}, ambient air temperature of 25degC, and wind velocity of 0.5m/s. When widening air gap from 20mm to 40mm, the cell temperature decreased 4degC, and the output increased 1.6%. In the case of installing photovoltaic modules on the roof considering the relation between the air gap in the heat balance state and the thickness of thermal boundary layer, heat from PV back was released outside the air gap if widening the air gap to more than 30-40mm. The type with a heat insulating material on the panel back decreased in output from other types. 5 refs., 7 figs., 4 tabs.

Report on evaluation of research and development of combined production systems aided by superhigh-functional lasers. Abstract; Chokoseino laser oyo fukugo seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Gaiyohen

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-04-01

This research and development project is aimed at development of combined production systems, which can flexibly, quickly process metallic stock materials in an integrated manner, with the objectives to promote rationalization and manpower saving for producing diversified types of machine parts in small quantities. Application of laser techniques to metal processing area is another objective of this project. The techniques to be developed by this project include those for system designing/controlling to integrate/combine the steps of processing and cutting stock materials, assembling the parts, and heat treatment and examination of the assemblies; for diversified types of cutting/processing by the mechanisms in which exchangeable constituent elements are assembled; for diversified types of processing shaped stock materials by the mechanisms in which molds and rolls are integrated; for diversified types of automatic assembling and transfer; for applying lasers to cutting, welding, heat treatment and measurement; for precision compensation and failure prediction by automatically diagnosing working conditions throughout the system; and for designs and production management for efficient production. The test plant has started general trial operation. (NEDO)

Euro-NCAP and the German ideas for new safety assessment of car in Europe; Euro-NCAAP to Europe ni okeru joyosha no atarashii anzen hyoka hoho ni taisuru Doitsu no kenkai

Energy Technology Data Exchange (ETDEWEB)

Omae, H. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

2000-03-01

This report summarized German's proposed revised plan of Euro-NCAP (European New Car Assessment Programme) presently implemented in Europe. As to the estimation of car safety, by entrusting it to Technical University Berlin in the latter half of the 1980s, German has been studying since then and summed up the results as TUB-NCAP. In this proposal, three tests were conducted on full-lap, offset front collision, and European side collision. The car damage in each collision form in accidents on the market, frequency of occurrence of handicap of each crew member. By putting weight of each frequency on the data obtained from each test, the estimation can be made comprehensively in a scoring method. In this method, wherever the test is conducted, the whole car can be estimated in the quantified form in which the objective element is not included. And the effect in the market accident also increases, and the accurate information is conveyed to users. It is unknown that in what form this German proposal can be reflected by Euro-NCAP and other countries. (NEDO)

Report on evaluation of research and development of combined production systems aided by superhighly functional laser. Evaluation; Chokoseino laser oyo fukugo seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Hyokahen

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-08-01

Described herein are combined production systems, capable of flexibly, quickly producing diversified types of machine members in small quantities in an integrated manner from raw stock processing to assembling/inspection. Development of the related techniques, including those for development of lasers of high output, has been implemented in an integrated manner for development of optical members, processing techniques and so on. The techniques developed by this project are expected to be applicable to various industrial purposes, because of their high synergistic effects. There was no oscillator of high output, when the project was started. This project has reduced device size and cost and improved their reliability, greatly contributing to expanded use of lasers. The solid-state lasers have been developed, not only for growing large-size crystals but also for transmission of light. The automation guidelines for assembling and inspection steps, which heavily depended on manual works, have been drawn. The machining functions have been improved by incorporating the processing techniques aided by lasers of high or medium output. One of the major problems involved in the conventional system is very time-consuming works required for establishing the software for the computer by which it is aided for operation. This problem has been solved by providing the modular structure machines developed by this project with flexibility of machining machine. (NEDO)

International research cooperation in fiscal 1997. Report on the research, development, and evaluation of environmentally-friendly combustion technologies; Kokusai kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Concerning the research and development of environmentally-friendly combustion technologies that had been conducted for six years beginning in 1992, analysis and discussion were made by a special committee dedicated to the evaluation of the efforts, and the outcome is stated. In the study of zeolite-base catalysts, a highly active catalyst was developed which assumes a multilayer structure of mordenite, etc., with titanium introduced thereinto using an NO-selective reducing catalyst. As for metal complex oxide-base catalysts, various catalysts high in activity were developed, based on saponite which is a laminar, clayey compound. As for alumina-base catalysts, details were learned of the reaction mechanism and catalysis activation sites and, helped by the findings, a silver-supporting alumina catalyst was produced. In the study of direct decomposition type NOx removing catalysts, a success was achieved in causing NO to be decomposed with high selectivity in an oxygen atmosphere by use of new-type electrodes, functional layers, and solid electrolytes. In the field of catalytic combustion, a PdO-Pt/Ba-Al2O3 catalyst was developed, which is to serve for a hybrid type catalytic combustion method. 19 refs., 112 figs., 25 tabs.

Fiscal 1997 research report on the survey on public test and evaluation organizations for development of welfare equipment; 1997 nendo fukushi kiki kaihatsu ni kakawaru koteki shiken hyoka kikan chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This research studies the construction policy of public test and evaluation systems for future development and practical use of welfare equipment, through survey on the current methods for development, practical test and evaluation of welfare equipment in countries advanced in welfare, and preparation of basic data for promoting establishment of public test and evaluation functions in Japan. Infrastructure preparation for standards and public test and evaluation organizations for developing welfare equipment is being promoted by Technical Laboratory of Bicycle Industry Promotion Association and some national organizations such as Product Evaluation Technical Center, Mechanical Engineering Laboratory, National Institute of Bioscience and Human Technology, and Living and JIS Center. However, preparation of objective and across test and evaluation systems for developing welfare equipment is still insufficient. Product Evaluation Technical Center is now approaching to evaluation and standardization of welfare equipment. Public test and evaluation organizations of the UK, Sweden and Denmark are presented. (NEDO)

Evaluation report on the study on the application of 3D woven C/C composite materials; Sanjigenori C/C composite zairyo no kikai buhin eno oyo ni kansuru kenkyu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described a study made during 1995 through 1998 on the application of 3D woven C/C composite materials to machine parts. The materials are large in rigidity, small in specific gravity, excellent in specific rigidity, and suitable for high speed rotation. They are excellent in heat resistance/dynamic reformation and expected as materials which can exceed limits of the existing steel for machine parts. However, to use them as machine parts, a possibility of high precision cutting is required. Therefore, a study was made on metal multi-layer membrane coating to C/C composites. Pitch-system high-elastic carbon fibers were made a 4-directional material by orienting horizontally in 3 directions at 120 degrees per plane and also orienting vertically. Various materials such as W, Mo and WC were coated by the laser assisted plasma hybrid spraying method. High adhesion coats with little pore were obtained. Multi-directionally woven C/C composites used to be poor in surface precision workability, but the problem was able to be solved by coating surfaces with metal layers and metal multi-layer membranes. The application is expanded not only to polygonal mirrors (for laser printing machine) and milling spindles, but largely to machine parts. 11 figs., 1 tab.

Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

Report on the final evaluation on the 'development of a bituminous coal liquefaction technology (NEDOL method)' in the Sunshine Project; Rekiseitan ekika gijutsu (NEDOL ho) kaihatsu saishu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-01

Development of a bituminous coal liquefaction technology (NEDOL method) can be judged appropriate as a national project in the comprehensive view with the 21st century just around the corner. It is a fact that this project has spent the national budget not in a small amount. There is no prospect of the technology to be put into practical use in Japan at the present time. The coal liquefaction technology is a technology required inevitably in the situation where shortage of crude oil supply may endanger the existence of a nation. Therefore, there is sufficient significance in having demonstrated the effectiveness of the NEDOL method which can be applied to a large number of coal types and expected of high liquefaction yield. The contents of the 'technological package' to be prepared are so demanded that its usefulness can be retained until the time of a demonstration plant design and operation will come in the future. It is also desired that the human resources and the testing devices will be kept ensured, and the technologies developed under this project will be maintained and expanded. The present technology has low necessity of immediately putting into practical use in Japan at the present time. However, the technology should be kept available for use at any time, and retained for use in an urgent situation. (NEDO)

Evaluation of mechanical properties of construction joint between new and old concrete under combined tensile and shear stresses; Shinkyu concrete no uchitsugime no incho sendan oryokuka no kyodo tokusei no hyoka

Energy Technology Data Exchange (ETDEWEB)

Ujiike, I. [Ehime University, Ehime (Japan). Faculty of Engineering; Yoshida, N. [Shikoku Railway Company, Kagawa (Japan); Morishita, S. [Oriental Construction Co. Ltd., Tokyo (Japan)

1998-01-15

The objective of this study is to examine the mechanical properties of construction joints between existing and newly placed concrete under combined tensile and shear stresses. Loading tests are conducted by using push off type specimens. The joint surface of existing concrete is roughened by shot blast and a half of the specimen is reconstructed by new concrete using ultra rapid hardening cement. The insufficient treatment of joint surface of the old concrete causes the lowering of tensile rigidity, while shearing rigidity is almost the same as that of the other specimen. The shearing and tensile rigidities of non jointed concrete and concrete shot blasted properly are not dependent on the combination of shearing and tensile forces. For the jointed concrete shot blasted insufficiently, the shearing rigidity decreases with the increase of tensile force and the tensile digidity also becomes lower by the action of shearing force. Both the tensile strength and shearing strength of jointed concrete become small compared to those of non jointed concrete. The ratio of reduction in tensile strength is larger than that in shearing strength. The strength of jointed concrete under combined tensile and shear stresses can be evaluated by Mohr`s failure envelope expressed by parabola tangent to both tensile strength circle and compressive strength circle. 7 refs., 12 figs., 2 tabs.

Evaluation report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; Hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The results achieved in fiscal 1992-1995 under the above-named project are stated. In the development of photocatalytic materials, a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus is developed. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is fabricated, which achieves a level higher than the denitration goal of 70%. Although the sheet in a 500-hour accelerated exposure test undergoes a hardening phenomenon in which elasticity decreases and tensile strength increases, yet degradation is hardly detected. Although a slight reduction is detected in denitration efficiency, yet it does not affect its practical application, and thus the durability goal is achieved. In the development of an energy conservation type air cleaning apparatus usable in underground parking areas or motorway tunnels, an apparatus capable of treating air at a rate of 2,000m{sup 3}/hour is fabricated, and this achieves a denitration level of not less than 80% in a field test (in the absence of rainfall). For denitration in the presence of rainfall, the apparatus is combined with an equimolar adsorption system, and a system capable of 80% denitration is proposed on the basis of data actually measured for each of the two. A conceptual design for a service model comprising a photodenitration and equimolar adsorption systems is evaluated, and it is found that it occupies less space than the existing models. (NEDO)

Fiscal 1999 technological survey report. Part 2. Applied technology for measuring human sense (Human sense measuring manual - basic technology for sense evaluation); Ningen kankaku keisoku manual. 2. Kankaku hyoka kiban gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A method of measuring/evaluating a mental and physical state by means of physiological information developed by a project was compiled into a 'guide book', as was a method of evaluating adaptability to the environment or products; and, this manual was prepared for the purpose of improving the adaptability of human beings to products by making use of the guide book widely in the field of industrial manufacturing. The part 2 explains a hard measuring instrument, evaluation device, simulation system, method of data analysis, etc., as 'basic technology for sense evaluation'. The chapter 1 is a new measuring and evaluation device (device for measuring physiological signals on the surface of the body, device for measuring visual characteristics, measuring device of in vivo substance, measuring device of thermal response, and system for evaluating adaptability of practical form), the chapter 2 is a new simulator (model of human body temperature with clothes on, human comfort meter, perspiring thermal manikin, and autonomic nerve control model in cardiac blood vessel/respiratory system), and the chapter 3 is new experimental/analytical method (new data analysis method and subjective evaluation questionnaire for stress assessment). (NEDO)

Evaluation of ride-quality and incidence of seasickness. 4. Motion sickness incidence and change of facial expression; Senpaku no norigokochi hyoka ni kansuru kenkyu ( 4 ). Norimonoyoi hasshoji no hyojo no henka

Energy Technology Data Exchange (ETDEWEB)

Arima, M.; Hirai, T.; Hosoda, R. [Osaka City Univ. (Japan)

1998-12-31

This paper studies the method of predicting and evaluating the motion sickness incidence from subject`s facial expressions during the whole-body exposure to oscillations. The facial expressions are recorded with a video camera which can measure them without invasion physiologically and mentally. Facial parameters, which are considered to relate to the motion sickness incidence, are selected, measured and analyzed quantitatively, and a method of evaluating the motion sickness incidence objectively from the facial expressions is proposed. Three facial expression parameters now selected to evaluate the motion sickness incidence are brow width, eye opening and mouth opening. It was clarified that the motion sickness incidence could be expressed joining the above parameters together. This paper consists of three sections, viz. Oscillation experiment for ride-quality evaluation, Measurement and analysis of facial expressions, and Modeling for evaluating facial expressions. 11 refs., 5 figs., 5 tabs.

FY 1977 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Photovoltaic power generation systems); 1977 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at investigation on irradiation conditions of natural solar radiation to establish the performance evaluation methods; establishment of standard evaluation methods under natural solar radiation; and investigation on practical problems involved in the photovoltaic power generation systems. The research items are (1) photovoltaic power generation systems, and (2) standard evaluation methods for photovoltaic power generation systems installed on the ground. The item (1) includes the effect analysis in which existing Japanese residential buildings are selected to estimate possibility of installation of photovoltaic power generation systems and possible quantity of power generated; conceptual designs in which several systems conceivable at present are proposed and outlined, and a 30kW photovoltaic power generation system is taken up to investigate, e.g., solar cell arrays for the system, orthogonal conversion devices, associated facilities, conceptual designs of storage batteries, problems involved therein, and future research themes; and operation of the cell, which takes up operational examples of solar cell power sources, and operational problems viewed from the power transmission side. The item (2) proposes the standard evaluation methods (primary drafts) for the solar cell arrays and panels as those for photovoltaic power generation systems installed on the ground. (NEDO)

FY 1978 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Photovoltaic power generation systems); 1978 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-03-01

This survey report provides the basic data for planning national projects to smoothly raise the large industry of solar cell industry in the future by studying how to promote the research and development projects for this area, continuously pursued from the establishment of the Sunshine Project. This report clarifies, first of all, the concept of long-term schedules for research and development of solar thermal power generation systems, based on which technical themes are concretely surveyed, and their economic viability and ripple effects on the other industries are analyzed. The industry of solar thermal power generation systems is a new industry, even based on the global horizons, backed up by the Japan's high-technological areas of electronics and semiconductor industries. It is one of important projects to be urgently developed, also viewed from the above standpoint. This report describes the long-term visions of solar thermal power generation systems, and the research and development projects therefor; stock materials for solar cells and problems involved therein; research and development projects for low-cost solar cells; photovoltaic power generation systems, and the research and development projects therefor; conceptual designs of photovoltaic power generation systems; and standard analytical procedures for solar cells, and technical problems involved therein. (NEDO)

Reports on 1979 result of Sunshine Project. Investigation and research on solar energy utilization system (solar thermal power generation system); 1979 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyonetsu hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

An investigation and research were conducted on the operation method of various solar thermal power generation systems and on the evaluation of the rating and cost performance; in the environmental test method for the equipment, the examination was continued for the test method and evaluation method concerning the absorbing surface and transmitting film; in the heat storing technology, an investigative research was done on the optimum heat storing method and energy conversion method suitable for the operation of the thermal power generation system, as well as performing, as an objective, a computer simulation on the total system with the purpose of clarifying the heat storing capacity. The results in the year were as follows. The operation method for solar thermal power generation was examined, as were the energy analysis, evaluation method of 1 MW pilot plant, the optimum utilization system of solar energy in the long run including its application, and technological economical problems to be solved for the next large solar thermal power generating plant. A discussion was carried out on the endurance test of the selective absorbing surface and transmitting film and on the durability of the reflection mirror. Evaluation and examination were made on the various materials of the 1 MW pilot plant. A review was done on various heat accumulating devices for solar thermal generation, mathematical thermal characteristics of heat accumulating devices, and future energy storing methods and problems. (NEDO)

FY 1978 Annual report on Sunshine Project results. Survey and research on systems utilizing solar energy (Photovoltaic power generation systems); 1978 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden system

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-03-01

This survey report provides the basic data for planning national projects to smoothly raise the large industry of solar cell industry in the future by studying how to promote the research and development projects for this area, continuously pursued from the establishment of the Sunshine Project. This report clarifies, first of all, the concept of long-term schedules for research and development of solar thermal power generation systems, based on which technical themes are concretely surveyed, and their economic viability and ripple effects on the other industries are analyzed. The industry of solar thermal power generation systems is a new industry, even based on the global horizons, backed up by the Japan's high-technological areas of electronics and semiconductor industries. It is one of important projects to be urgently developed, also viewed from the above standpoint. This report describes the long-term visions of solar thermal power generation systems, and the research and development projects therefor; stock materials for solar cells and problems involved therein; research and development projects for low-cost solar cells; photovoltaic power generation systems, and the research and development projects therefor; conceptual designs of photovoltaic power generation systems; and standard analytical procedures for solar cells, and technical problems involved therein. (NEDO)

Development of technology for thin substrate polycrystalline solar cells for practical use. Survey on analysis for practical use; Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on the manufacturing technology trend of thin substrate solar cells for practical use in fiscal 1994. In production of Si raw material, as electron beam melting and ingot production are combined, C, P, Ca and Al are removed by evaporation, while Fe and Ti by solidifying segregation. As the basic technology of continuous casting for substrate production, a drop coagulation method for Si melt is under investigation which is more advantageous in unidirectional solidification and cell conversion efficiency than conventional methods. The cost and future of single crystal Si and polycrystal Si were compared on the basis of document survey. Every institute commonly uses FZ substrates to produce single crystal Si cells, and SiO2 for surface passivation. New cell structure, hetero-structure, thin cell, crystalline defect and lifetime are under investigation for ultrahigh-efficiency solar cells. The technology trend was also surveyed through academic societies and conferences. 5 tabs.

33rd Solar Energy Promotion Committee Meeting - 8th Photovoltaic Power Liaison Meeting. Report for fiscal 1995; Dai 33 kai taiyo energy suishin iinkai dai 8 kai taiyoko hatsuden renrakukai (1995 nendo hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-22

The above-named events were convened in the period of April 22-24, 1996, when a total of 46 presentations were given on research achievements. In the session on crystalline Si systems, 9 essays were presented, and a discussion was held about 'Technological tasks for realizing 20% efficient module.' In the session on ultrahigh III-V group systems, 4 essays were presented, and a discussion was held on 'Tasks about technology development for ultrahigh efficiency III-V compound solar cell.' In the session on thin film (a-Si) systems, 14 essays were presented, including one about an approach toward the elucidation of photodegradation. In the symposium, a subject 'System-to-cell transverse task' was discussed. In the session on system related matters, 10 essays were presented, and a discussion was held about 'Architecture and photovoltaic system.' In the session on thin film (thin film polycrystalline Si, chalcopyrite) systems, 8 essays were presented, and a subject was discussed titled 'Toward the establishment of a system of widespread diffusion and massive introduction.' (NEDO)

33rd Solar Energy Promotion Committee Meeting - 8th Photovoltaic Power Liaison Meeting. Report for fiscal 1995; Dai 33 kai taiyo energy suishin iinkai dai 8 kai taiyoko hatsuden renrakukai (1995 nendo hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-22

The above-named events were convened in the period of April 22-24, 1996, when a total of 46 presentations were given on research achievements. In the session on crystalline Si systems, 9 essays were presented, and a discussion was held about 'Technological tasks for realizing 20% efficient module.' In the session on ultrahigh III-V group systems, 4 essays were presented, and a discussion was held on 'Tasks about technology development for ultrahigh efficiency III-V compound solar cell.' In the session on thin film (a-Si) systems, 14 essays were presented, including one about an approach toward the elucidation of photodegradation. In the symposium, a subject 'System-to-cell transverse task' was discussed. In the session on system related matters, 10 essays were presented, and a discussion was held about 'Architecture and photovoltaic system.' In the session on thin film (thin film polycrystalline Si, chalcopyrite) systems, 8 essays were presented, and a subject was discussed titled 'Toward the establishment of a system of widespread diffusion and massive introduction.' (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology - Separate volume: Collection of data of photovoltaic power generation systems); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu - Bessatsu: taiyoko hatsuden system data shu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the establishment of technologies for optimum designs and optimum operation for various types of photovoltaic power systems, data are compiled in this volume, collected from the field test facilities and residential photovoltaic power systems. Operating data and meteorological data from the field test facilities (interconnection system, independent system, and water pump system) are arranged as easy-to-use supplementary data to help studies in relation to the 'energy flow in the test field facility systems' which is in the fiscal 1999 achievement report. As for data collected from residential photovoltaic power systems, they are arranged as easy-to-use supplementary data to help studies in relation to the 'Data and evaluation of residential photovoltaic power systems' which again belongs in the fiscal 1999 achievement report. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of novel voltaic cell structure solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The present state and trend are surveyed of organic ferroelectric thin films, new carbon materials, fullerene compounds, and thermophotovoltaic (TPV) power. In the study of organic ferroelectric thin-film solar cells, the effort still remains at the basic stage, with the conversion rate as low as 3% in Europe and 2% in Japan. The progress of basic studies, however, is worth attention. It is deemed that 15% is the photoconversion rate to be currently expected from new carbon material solar cells. Fullerene compounds include some semiconductors whose bandgap values may be controlled across a 0.75-1.95eV range, and they may find their place in thin-film solar cells. However, their physical properties are not fully known, and their development into devices such as solar cells is scarcely reported. The research and development of TPV in the U.S. is led by NASA (National Aeronautics and Space Administration) and NREL (National Renewable Energy Laboratory), with their efforts concentrated on the development of portable power sources utilizing combustion heat. In Europe, TPV application to small-scale residential cogeneration systems is under study. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of environmental adaptation of next-generation solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - jisedai taiyo denchi kaihatsu kankyo tekioka chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Surveys are conducted of photovoltaic power system development projects and their utilization in Japan and overseas, and a discussion is made on the progress, technical challenges, effects, and implementation systems relating to the solar cell application technology development project under the New Sunshine Program. Compiled in the report are the results of surveys of the research and development of photovoltaic power systems and their diffusion in the U.S. and European nations, and the research and development strategies for and the trends of the development of various types of solar cells in these countries. The trends of research and development of non-conventional type solar cells are also collected, which include 3 cases of TPV (thermophotovoltaic) devices, 5 cases of new inorganic materials, 1 case of new organic materials, and 4 cases of dye-sensitized solar cells. In relation to the status of resources of crystalline compound-based solar cell materials, raw materials for solar cells other than silicon are taken up, and their reserves, manufacturing methods, quantities yielded and consumed, costs, etc., are surveyed. These are all taken into consideration in discussing the basic approach to the study of future research and development as it ought to be. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Feasibility study of wet-type solar cell commercialization); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu, Shuhen yoso gijutsu ni kansuru chosa kenkyu - Shissiki taiyo denchi jitsuyoka kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Dye-sensitized solar cell commercialization was studied for feasibility. Studies were made about photoelectric conversion efficiency and various factors supposedly to affect the life and other properties, and a wet-type (dye-sensitized type) solar cell was fabricated. In an endurance test, the dye-sensitized solar cell retained its initial performance after 3,500 hours of continuous irradiation. A 16 cm{sup 2}-large integrated type Graetzel cell was fabricated, and it achieved a photoelectric conversion efficiency of 4.6%. Furthermore, in the study of Graetzel cells, possibility of the creation of new electrolytic solutions was discussed, a non-TiO{sub 2} dye-sensitized solar cell was fabricated based on the self-assembled electrodeposition of the ZnO dye, and the feasibility was deliberated of a dye-sensitized solar sell using a composite oxide semiconductor. Concerning their development in the future, it was concluded that dye-sensitized solar cells including the Graetzel cell were equipped with the basic characteristics of a next-generation solar cell that would be requested to be low in cost and high in performance. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of ultrahigh-efficiency solar cell application fields); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu, Shuhen yoso gijutsu ni kansuru chosa kenkyu (Chokokoritsu taiyo denchi tou oyo bunya kaitaku chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Surveys and studies were conducted in order to make propositions concerning the fields of application wherein the merits of ultrahigh-efficiency solar cells would be fully utilized. A questionnaire was held about solar cell application fields, and studies were made about new systems based on the need in the market for specific solar cell goods and capable of supporting their mass diffusion. Proposed as the result was the establishment of a rental (lease) system for photovoltaic power systems, a local photovoltaics advisory system, a market for used photovoltaic power systems, and so forth. In the feasibility study of photovoltaic power generation on unused land in agricultural villages, surveys were conducted concerning energy problems, the energy structure, the actual state of energy consumption, the abandoned farm and its utilization, and so forth. Propositions involving photovoltaic power feasibility were then made, which covered power consumption for greenhouse culture, energy supply for producing methanol out of biomass, power sources for insect incapacitating yellow fluorescent lamps, power sources for livestock barn air-conditioning, power sources for animal excretion treatment, and so forth. (NEDO)

FY 1999 report on the results of the R and D on the assessment of reliability of oil refining facilities; 1999 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

At present, in oil refineries in Japan, the term of the continued operation in oil refining facilities is shorter than that in Europe and America because of the regulation on the open inspection period for boilers and hazardous material storage tanks. As a result, the refining cost is comparatively higher than in Europe and America due to the increase in inspection/repair cost and decrease in operational rate. Therefore, it is becoming important to effectively supply petroleum products by keeping stability in oil refining facilities of the whole Japan and prolonging the term of the continued operation of oil refining facilities, etc. In this R and D, the technical development is conducted which is needed for the long-term continued operation of oil refining facilities. The items for the R and D are as follows: assessment technology of reliability of oil refining high temperature system facilities, assessment technology of reliability of piping/storage facilities in oil refinery, assessment technology of reliability of oil refining power system facilities, technology of management support system in oil refining facilities. In this fiscal year, technical survey, data collection, and construction of the basic concept of developmental technology were mostly conducted. Also conducted were trial manufacture of various probes for non-fracture inspection use, oscillators, etc., and basic design of inspection equipment and trial manufacture of a part of them. And the data acquired were analyzed. (NEDO)

Research on the general analytical method of fossil fuel cycle from a viewpoint of the global environment. 3; Chikyu kankyo kara mita sogoteki kaseki nenryo cycle bunseki hyoka shuho no chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The general analysis/assessment method of a fossil fuel cycle was studied. Seven kinds of power generation plants such as LNG cycle and coal cycle ones, and four kinds of transport and treatment systems of recovered CO2 such as ocean and underground systems were studied as case studies on life cycle analysis. As data necessary for life cycle analysis, the database was constructed which stores the facilities and operational energy required for a total energy system from mining of fossil fuel to treatment of recovered CO2, and the quantity of environmental waste such as CO2 emission. As a result, the decrease rate of energy balance defined as ratio of input energy to power plant output was estimated to be 14-43% and 20-60% in LNG cycle and coal cycle, respectively. Even if the recovery rate of CO2 in power plants reached 80-90%, reduction of total CO2 emission was limited to only 20-40% because of CO2 emission during mining, liquefaction and transport of fuel. 168 refs., 48 figs., 102 tabs.

Evaluation of the autonomic neuropathy function immediately after a change to upright posture using the impulse response function; Impulse oto kansu wo mochiita shisei henkan katoki ni okeru jiritsu shinkei kino hyoka

Energy Technology Data Exchange (ETDEWEB)

Yokoyama, K. [Nagoya City University, Nagoya (Japan); Moyoshi, M.; Takata, K. [Daido Institute of Technology, Nagoya (Japan); Watanabe, Y. [Toyota College of Technology, Aichi (Japan)

1997-05-20

Autonomic neuropathy function immediately after a change to upright posture has been evaluated by applying transient response function of the system to the blood regulation system. The impulse response function was determined from the change in heart rate before postural change to the upright posture, and was compared with the transient change immediately after a change to the upright posture. The time series of R-R interval of electrocardiogram was used as the time series of the change in heart rate. To determine the impulse response function, an autoregressive model was applied to the R-R interval time series. The impulse response function at the steady state is a transient reaction at the impulse stimulation added to the blood regulation system. The R-R interval decreases rapidly by the autonomic neuropathy reaction in which the blood is rapidly transferred into the legs immediately after a change to upright posture. There is a close correlation between the initial temporary decrease in R-R interval and the impulse response function derived from the change in heart rate immediately after a change to the upright posture. Accordingly, the blood regulation and autonomic neuropathy functions can be evaluated by the impulse response function without actual standing test and load of tested persons. 9 refs., 3 figs., 1 tab.

Research on estimation of methane generated in paddy field and release mechanism of the gas into the atmosphere. Suiden ni okeru methane hasseiryo no hyoka to sono hoshutsu kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Minami, K; Nouchi, I; Yagi, K [National Institute of Agro-Environmental Science, Tsukuba (Japan)

1991-11-25

Research and estimation have been carried out on a mechanism to generate methane in paddy fields, which relates closely to global warming. For methane flux measurement, the chamber method was used. The result revealed that with paddy fields mixed with organic substances, methane generation was abundant in the order of raw rice straw mixed area > rice straw compost mixed area > chemical fertilizer mixed area. At the Ryugasaki test area, the raw rice straw and fertilizer mixed areas have generated methane annually at 27.0 gm[sup [minus]2] and 8.2 gm[sup [minus]2], respectively. With regard to soil types, the order was peat soil > gley soil > Kuroboku soil > light-colored Kuroboku soil, where the peat soil generated about 40 times as much of methane as the light-colored Kuroboku soil. As regards the influence from drainage adjustment, normally water-filled field, wet field, and dry field generated methane at 9.25, 4.79, and 0.34 gm[sup [minus]1] y[sup [minus]1], respectively. Amount of methane generated annually from paddy fields over the whole world was estimated at 22 to 73[times]10[sup 12] g. It was determined from the above facts that methane generation may be reduced if organic substance mixing and water in paddy fields are controlled properly. 8 refs., 5 figs., 1 tab.

Evaluation of performance for solar house with Trombe wall. Part 6; Trombe kabeshiki solar house no hyoka kenkyu (toki tan`i ni okeru Trombe heki naihyomen kyuhonetsuryo no santei hoho no kento)

Energy Technology Data Exchange (ETDEWEB)

Yamazaki, R.; Nakajima, Y. [Kogakuin University, Tokyo (Japan); Yoshida, N. [Nishimatsu Construction Co. Ltd., Tokyo (Japan); Watanabe, T. [Tokyo Electric Power Service Co. Ltd., Tokyo (Japan); Abe, H. [National Land Agency, Tokyo (Japan); Yamaga, K. [Mitsubishi Estate Co. Ltd., Tokyo (Japan)

1997-11-25

`Equivalent heat loss factor` used in the simplified load calculation method for the Trombe wall is a version modified to fit a solar house equipped with a Trombe wall. To compute the factor, it is necessary to input the quantities of Trombe wall inner surface absorbed/radiated heat for whose calculation the effect of the delay in solar heat storage by the Trombe wall has to be taken into consideration. The daily summation of the quantities of absorbed/radiated heat can be easily calculated using the day`s and the previous day`s insolation amounts. In this report, the hourly summation of the quantities of Trombe wall surface absorbed/radiated heat is performed by use of two variables which are the day`s and the previous day`s insolation amounts. In calculating the hourly summation of the quantities of absorbed/radiated heat, the daily summation of the quantities of absorbed/radiated heat is first calculated using the chart of predicted lines for the Trombe wall and, based on the data thus obtained, the quantities of absorbed/absorbed heat are divided and assigned to the respective hours and, as the result, approximations are obtained for the calculation of the hourly summation of the quantities of Trombe wall absorbed/radiated heat. A `time-dependent performance prediction curves for the Trombe wall` is proposed, which enables the visual comprehension of the effect of Trombe wall hourly units. 1 ref., 10 figs., 2 tabs.

Fiscal 1998 survey report. Assessment and analysis of collected data in wind power generation field test project; 1998 nendo furyoku hatsuden field test jigyo ni okeru shushu data hyoka kaiseki chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Examination was made on wind conditions, power generating characteristics, and the reliability of a system by analyzing the operation record of the wind power generation equipment which was installed at Hiraizumi-cho, Nishi-Iwai gun, Iwate prefecture and at Misaki-cho, Miura-shi, Kanagawa prefecture. The equipment at Hiraizumi had a rated output of 490 kW, and at Miura 400 kW. The period of the examination was from April, 1998 through February, 1999, the items for data collection being the generator output, generated energy, average wind velocity, record of abnormality occurrence, and maximum wind velocity. At Hiraizumi, annual average utilization rate was 12.9%; annual average operation rate, 49.9%; average wind velocity, 4.6 m/s; and maximum wind velocity of the period, 31 m/s. At Miura, annual average utilization rate was 16.5%; annual average operation rate, 77.0%; and average wind velocity, 5.0 m/s. The utilization rate is desirably 17%. The top three abnormalities were drop in AC control voltage, actuation of main shaft brake and eddy current/actuation of open phase relay, accounting for 83.3% of the total abnormalities at Hiraizumi, while they were unbalance in current, grid drop and automatic unwinding of cable, accounting for 74.5% at Miura. (NEDO)

Ab initio MO study on the thermal stability of 1-phenyl-1H-tetrazoles; Hikeikenteki bunshi kidoho ni yoru 1-Ph-1H tetorazoru yudotai no netsu anteisei hyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Ono, Yoshio.; Akutsu, Yoshiaki.; Arai, Mitsuru.; Tamura, Masamitsu. [The University of Tokyo, Tokyo (Japan). School of Engineering; Matsunaga, Takehiro. [National Institute of Materials and Chemical Research, Tsukuba (Japan)

1999-06-30

Ab initio MO calculations of 1-phenyl-1H-tetrazoles were carried out, in order to explain a substituent effects on its high thermal stability and to estimate the thermal stability of the other tetrazoles. Similar to 1H-tetrazole, five bonds in the tetrazole ring have intermediate lengths between single and double bond lengths. Phenyl and tetrazole rings are not both on one plane showing no interaction. Three indexes addopted as a measure of thermal stability indicate that the more equal the bond lengths of the ring are and that the bigger the stabilization energy by ring formation is, the more thermally stable they are. It is found out that there is the relationship between the thermal stability and the ring charge. That is, the more negative the ring charge is, the more thrmally stable the tetrazole is. Also, there is a good relationship between the thermal stability and the energy level of orbital of which orbital is an anti bonding type with respect to the N3-N4 bond. The higher the energy level is, the more thermally stable the tetrazole is. (author)

Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

Study on driver`s stress in lane-change maneuver. Evaluation and analysis of heat rate change; Shasen henkoji no untensha no kinchodo kaiseki. Shinpaku hendo no gen`in bunrui to sono hyoka

Energy Technology Data Exchange (ETDEWEB)

Sumida, K [Mitsubishi Motors Corp., Tokyo (Japan); Chikamori, S; Shimizu, Y [Seikei University, Tokyo (Japan)

1997-10-01

We measured the changes of heart rate in order to analyze the drivers` stress while they tried high speed lane-change on the stationary driving simulator. We concluded that the reasons of the chances were mainly dependent on the following two items. (1) mental pressure caused by the coming task of lane-change, (2) mental disturbance by the task to keep the vehicle inside the lane. By using the mental pressure and disturbance, we could evaluate the stability of the vehicles in lane-change maneuver. 3 refs., 11 figs.

Effects on annual cost of solar/air-heat utilization system of carbon tax and interest rate for a residential house; Jutakuyo taiyo/taikinetsu riyo system no nenkan keihi ni oyobosu tansozei kinri no eikyo

Energy Technology Data Exchange (ETDEWEB)

Shen, Q; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan). Faculty of Engineering

1996-10-27

In recent years, a system has been proposed that utilizes river heat, air-heat, exhaust heat from a cooler, etc., in addition to natural energy for the heat pump. With the introduction of such system, the amount of energy used and that of CO2 exhaust will be greatly reduced, but annual expenses will be increased as it stands. In order to improve the cost efficiency of the system, a proposal has been made for the introduction of an economic policy such as the carbon tax and a low interest financing system. With these matters in the background, the subject study predicts the production of solar cells in the future and, on the basis of this production, determines the price, conversion efficiency and equipment energy of solar cells in the future. Using these values and taking into consideration the introduction of the carbon tax and the low interest financing system, the optimum area was determined for solar cells and heat concentrators in a future residential solar/air-heat energy system. The carbon tax, being imposed on all CO2 discharges, had a large effect. Moreover, as the tax increased, annual expenses decreased for the solar/air-heat system. 3 refs., 6 figs.

FY 1999 report on the verification test on the system interconnection of the photovoltaic power system in Malaysia; 1999 nendo Malaysia ni okeru taiyo denchi hatsuden system no keito renkei jissho shiken seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

JET and SIRIM Behad, which is the standards and industrial research institute in Malaysia, worked this project together, and installed the Photo Voltaic Generation System (hereinafter refferred to as 'PV system') on the roof of the research building for researching basic conditions in the practical use of the PV system by gathering basic data. The power quality of a supply system necessary for a grid connection of the PV system was researched in the evidential experiment. Moreover, the invasion level and the invasion frequency to the PV system of the thunder surge by the peculiar weather condition in this region were researched. In addition, the requisite for the islanding function for the alternative emergency power supply was investigated. The contents of this project were composed of the three items. (1) research of the power quality in low voltage distribution system. Before and after the PV system is connected with the supply system, basic data concerning the power quality of the voltage, the current, and the frequency fluctuation, etc. in the system was collected. (1)measurement and investigation of the power quality under the current low voltage distribution system. By connecting ad monitoring recorder with a lower voltage distribution system, the current power quality i.e. voltage, current, frequency the fluctuation of voltage and frequency at the regular time were measured and investigated. (2) The power quality in the supply system grid connection of the PV system was measured and investigated. The voltage and the frequency in the case of supply system grid connection of the PV system were compared with the current state of preceding clause 1 and the stability of the power quality was evaluated. Moreover the output power of the solar battery was connected with the measurement device and then the surface temperature of the solar battery module, DC voltage, current and quality of solar radiation were measured. The subject in the practical use of the PV system in Malaysia was extracted through these experiments. (2) Research of level and frequency of the thunder surge. 1. Measurement of level and frequency of the thunder surge by the thunder surge counter. The thunder surge counter was set up respectively on the positive line and the negative line of the solar battery. These signals are taken into the memory of the thunder surge counter, and the level and the frequency data of the thunder surge which invade the PV system were accumulated. 2. Evaluation by simulation. The PV system was evaluated to the thunder surge obtained in preceding clause 1 by the simulation. In addition the simulation analysis was conducted by the system equivalent circuit on the assumption of the thunder surge current at the location of the system. (3) Research of the islanding function of the PV system as the backup power supply was evaluated when blacking out. (NEDO)

Evaluation report on research and development of an ultra high performance laser applied composite production system. Achievement report; Chokoseino laser oyo fukugo seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Seika hokokuhen

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-08-01

Research, development, and evaluation were made on a composite production system applicable to manufacture products of a large number of types in small quantities. In the research and development of a total system, verification works were carried out by studying basic designs, operation of the composite production system, and experiment plant operation. Research and development on cutting and processing technologies included studies on composite cutting mechanisms, general purpose fitting technologies, control systems, and drive systems. In the research and development of laser applied technologies, studies were performed on large output laser oscillators, the control thereof, and laser processing technologies. In the research and development of automatic diagnosis technologies, studies were executed on failure diagnosis, accuracy compensation, automatic inspection, and accuracy diagnostic technologies. In the research and development of design and control technologies, studies were carried out on automatic designing, process designing, and process controlling technologies. In the study of operation of the Tsukuba experiment plant, discussions were given on configuration of the experiment plant, laser processing mechanism, composite assembly mechanism, production inspection mechanism, and system operation. Furthermore, design studies were also carried out on practically usable systems. (NEDO)

Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (interim report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

Development was made on a technology to evaluate quality of composite materials. Few data are available for environmental resistance of composite materials, whereas identification of environmental deterioration behavior and establishment of a environmental resistance evaluating technology are a significant issue in utilizing these materials as new materials for space, aeronautics, and marine applications in the future. The present research was taken up with objectives to elucidate deterioration behavior of composite materials exposed to special environment in the atmosphere and space and to establish methods for acceleration tests and environmental performance evaluation by using simulated environments equivalent to the natural environment exposure. The former period (fiscal 1982 through 1984) has investigated environmental conditions in the atmosphere and space, prepared standard test specimens, performed design on environmental devices simulating the environmental elements, as well as tests on deterioration due to environmental elements, and systematized the deterioration characteristics to establish composite test conditions. The latter period (fiscal 1985 through 1988) has developed the composite environment testing device based on the result achieved in the former period, elucidated the deterioration behavior under the composite environmental conditions, and performed evaluation tests on the developed composite materials (FRP). (NEDO)

FY1995 development of a clean CVD process by evaluation and control of gas phase nucleation phenomena; 1995 nendo kisokaku seisei gensho no hyoka to seigyo ni yoru clean CVD process no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of this study is to develop a high-rate and clean chemical vapor deposition (CVD) process as a breakthrough technique to overcome the problems that particles generated in the gas phase during CVD process for preparation of functional thin films cause reduced product yield and deterioration of the films. In the CVD process proposed here, reactant gas and generated particles are electrically charged to control the motion of them with an electric field. In this study, gas-phase nucleation phenomena are evaluated both theoretically and experimentally. A high-rate, ionized CVD method is first developed, in which reactant gas and generated particles are charged with negative ions generated from a radioisotope source and the UV/photoelectron method, and the motion of the charged gas and particles is controlled with an electric field. Charging and transport processes of fine particles are then investigated experimentally and theoretically to develop a clean CVD method in which generated particles are removed with the electric forces. As a result, quantitative evaluation of the charging and transport process was made possible. We also developed devices for measuring the size distribution and concentration of fine particles in low pressure gas such as those found in plasma CVD processes. In addition, numerical simulation and experiments in this study for a TEOS/O{sub 3} CVD process to prepare thin films could determine reaction rates which have not been known so far and give information on selecting good operation conditions for the process. (NEDO)

Evaluation and analysis of long-term operation data for a grid connected PV generation system; Nippon de hajimete no gyakuchoryu ari kojin jutaku taiyoko hatsuden system no choki unten jisseki no hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

Ishida, T.; Kozuma, S.; Hagihara, R.; Kishi, H.; Uchihashi, K.; Tsuda, S.; Nakano, S. [Sanyo Denki Co. Ltd., Tokyo (Japan)

1997-11-25

Long-term operation of a photovoltaic power generation system installed in a private residence in Osaka in 1992 is evaluated. Since the sale of power by back flow was approved five years ago, it has been working continuously without troubles. The evaluation covers the array output coefficient, inverter performance, system output coefficient, and power generation and sale track records. The findings obtained are mentioned below. Regular seasonal changes are observed in the array output coefficient, high in winter and low in summer, but the variation is smaller in amorphous arrays than in polycrystalline arrays. The monthly level of inverter performance is almost in all months higher than 0.90 specified for standard operation. The overall system output coefficient is 0.749, which is higher than the average value in NEDO`s field test business report. A total of 7852kWh has been generated since the system started operation five years ago, of which 3787kWh or 48% has been sold. 3 refs., 9 figs., 5 tabs.

Fiscal 1999 technological survey report. Part 1. Applied technology for measuring human sense (Human sense measuring manual - human sense evaluation index guideline); Ningen kankaku keisoku manual. 1. Ningen kankaku hyoka shihyo guide line

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A method of measuring/evaluating a mental and physical state by means of physiological information developed by a project was compiled into a 'guide book', as was a method of evaluating adaptability to the environment or products; and, this manual was prepared for the purpose of improving the adaptability of human beings to products by making use of the guide book widely in the field of industrial manufacturing. Described in the part 1 are a method of evaluating human mind and body by the measurement of physiological quantity, a method of evaluating mental and physical adaptability from the element of environmental physics such as vision, sound and warmth, and a method of evaluating adaptability concerning utilization of machines and equipment, as 'human sense evaluation indexes'. The chapter 1 is the index of physiological/psychological state (stress evaluation index, fatigue/awakening evaluation index), the chapter 2 is an environmental/psychological index (overall environmental evaluation index, visual environmental effect index, sound/vibration environmental evaluation index, thermal environmental evaluation index), the chapter 3 is an adaptability evaluation index of products and the like (adaptability evaluation index by form and movement, evaluation index for operability of equipment for example), and the chapter 4 is the guideline (of environmental design and of product design). (NEDO)

Formation of secondary products in water purification. ; Toxicological evaluation of mutagenic chlorination by-products during drinking water treatment. Josui shori ni okeru fukuseiseibutsu. ; Josui shori ni okeru hen'i genseibusshitsu no dokusei hyoka

Energy Technology Data Exchange (ETDEWEB)

Nakamuro, K [Setsunan Univ., Osaka (Japan). Faculty of Pharmaceutical Sciences; Sayato, Y [Setsunan Univ., Osaka (Japan)

1993-12-10

The biological effects of acute toxicity, chronic toxicity, carcinogenicity, etc. of chlorination by-products detected in drinking water in Japan are discussed. The biological effects of representative chlorination by-products such as trihalomethane, haloacetic acid, haloaldehyde, haloacetonitrile, chlorophenol, chloropicrin, etc. as well as the evaluation of mutagenicity in drinking water purification process, for which Ames Salmonella/microsome assay is used for safety evaluation of drinking water, are discussed. The extent of the contribution of mutagenicity of chlorination disinfection by-products to the mutagenicity of drinking water is investigated. It must be admitted that biological evaluation of the safety of water quality is impossible currently by using only the known chemical substances contained in drinking water. The effects of chlorination and ozone treatment which are often applied to drinking water treatment are different each other. 58 refs., 1 fig., 4 tabs.

Report on the basic design of a hydrogen transportation system utilizing metal hydrides and the evaluation thereon; Kinzoku suisokabutsu wo riyoshita suiso yuso system no kihon sekkei to sono hyoka ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-26

This paper describes a hydrogen transportation system utilizing metal hydrides. For a storage method for moving, metal hydrides having high hydrogen containing performance like Mg-based hydrides would have high portability, less weight disadvantage, and high economic performance. In the fixed location storage, metal hydrides are superior in safety and maintenance cost to the conventional high-pressure gas holder and liquefied hydrogen storage. Because of their high dependence on equilibrium pressure and temperature, the significance of development thereof is large as the source of high-pressure hydrogen generation and motive force. More effective utilization of low-level heat, and separation and refining of hydrogen may also be expected. With regard to fuel supply for hydrogen fueled automobiles, metal hydrides are better in safety and total energy cost than liquefied hydrogen, but have a number of disadvantageous points in weight demerit. Eliminating the weight demerit would be the central issue of the development. Accompanying the development of hydrogen fueled automobiles, there are a number of technological elements to be developed on fuel supply system, such as storage, moving and transportation in hydrogen manufacturing sites, and filling and storage at using sites. Arranging the related infrastructures would be the issue. (NEDO)

Life cycle assessment of supercharger for automotive use. Small displacement, high charging pressure engine and environmental load; Jidosha tosaiyo supercharger no life cycle assessment (LCA hyoka). Shohaikiryo kokakyu engine no kankyo eno yasashisa

Energy Technology Data Exchange (ETDEWEB)

Takabe, S; Sonoya, T; Hara, M [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1997-10-01

In resent years environmental conservation requires low fuel consumption and low emission engine. And environmental load of every car life stage (production, using, abolition) is considered. Life Cycle Assessment of supercharging small displacement engine is reported, compared with natural aspirated engine as same maximum torque and maximum power as supercharging engine. 6 refs., 8 figs., 3 tabs.

Report on the evaluation of the development of the catalyst surface high accuracy quantitative analysis technology using electron spectroscopy; Denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki gijutsu no kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

An objective evaluation from a third party was conducted on the purpose, plan, execution method, achievement, etc. of a project 'The devilment of the catalyst surface high accuracy quantitative analysis technology using electron spectroscopy.' The purpose of the project is to make the relationing possible between the analytical results of the catalyst surface and the catalyst performance which has been so far difficult by heightening the accuracy of the catalyst quantitative surface analytical accuracy using the electron spectroscopy. The purpose and significance are judged to be worth a lot. This project is an industry/university/government joint project between the two countries. The project is excellent both in connection among research institutes and leadership of chief researchers, and it is judged that the joint research system fully functioned. The term of the project was shortened from 3 years in the first plan to 2 years, and therefore, the study was finished only on silicon oxide and organic thin films. However, it was determined that the study results are to be run in the magazine 'Surface and Interface Analysis,' which indicates that the achievement was judged to be very worth in the academic viewpoint. (NEDO)

Report on evaluation of research and development of production of olefins from heavy oil as the stock material; 'Jushitsuyu wo genryo to suru olefin no seizoho' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-08-01

This project is aimed at stable supply of the stocks for the petrochemical industry to cope with the keenly felt depletion of oil resources in the long run and price hikes, and promotion of effective utilization of high-sulfur heavy oil fractions difficult to desulfurize, thereby promoting prevention of pollution. The techniques have been developed to economically produce high-value products, e.g., olefins and aromatic hydrocarbons, by thermally cracking abundant stocks, e.g., vacuum residue. A 120 t/d fluidized bed pilot plant with coke as the heat medium was constructed to develop various techniques, e.g., those for controlling coking, decoking, quenching cracking products, and controlling coke particles as the heat medium, to realize stable, continuous operation for extended periods of at least 1,000 hours. The techniques have been also developed for effective utilization of heavy oils as by-products containing sulfur at high concentrations. Economic viability of the process is considered to be on a level with that associated with naphtha cracking at present, when an intermediate base vacuum residue is used as the stock material. It will be sufficiently competitive with naphtha cracking with all types of heavy oils as the stock materials, including intermediate base vacuum residue, in an intermediate term. (NEDO)

Fiscal 2000 achievement report on the research and development of transfer standard gage for oil flowmeter (final assessment); 2000 nendo sekiyu ryuryokei no iten hyojunki no kenkyu kaihatsu seika hokokusho (saishu hyoka hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In a servo PD (positive displacement) flowmeter for oil, a differential pressure transmitter detects difference in pressure between the PD flowmeter input and output ports and a rotor is driven by a servo motor so that the pressure difference between before and after the PD flowmeter rotor will be zero. The design enables high-accuracy measurement across a wide range of flow rates and is not easily affected by the surrounding physical conditions such as viscosity and density. For the development of such a flowmeter, it is necessary to develop a rotor that rotates smoothly free of locking in a steady and uniform flow, to build a visualized model that enables the analysis of flow inside the flowmeter which in turn will enable the determination of optimum differential pressure detecting ports, and to connect a newly developed servo mechanism to the thus determined ports. As the result of the research, a servo PD flowmeter is developed, which is a 50mm diameter prototype employing the Invoflex tooth form which is the waveform for a rotor suitable for a high performance flowmeter. Placed in a generally used oil flow calibration liquid, which is gasoline, kerosene, or the like, it covers a flow rate range of 1:10 and reads with an accuracy of {+-}0.1%. It remains stable in performance and suffers but a little change with the passage of time. (NEDO)

Report on a survey in fiscal 1999. Analysis of English literatures related to unified evaluation models for global warming; 1999 nendo chikyu ondanka togo hyoka model kanren eibun shiryo no bunseki choa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper summarizes the basic materials related to unified evaluation models for global warming. The unified evaluation is a disciplinary process to combine, interpret and share the information from different scientific disciplinary areas in such a form that the whole cause and effect chain can be evaluated from a macroscopic view. The process has higher utilization value than the evaluation overemphasizing a single academic area, and can provide decision makers with useful information. The process is suitable to model complex interactions and feedback mechanisms in diversified scenes such as climate change. The unified evaluation can identify the policy criteria along with a measure framework having consistency. The evaluation process is repetitive and continuous, wherein a science community can convey comprehensive knowledge and finding to a decision making community. In turn, the decision making side can feed back the experiences and achievements in learning. Execution of the evaluation requires different approaches, such as judgement of specialists including the modeling methods and experience, discovery as a result of applying the policies, and survey methods. The paper also describes the gaming conception, scenario analysis, and unification evaluation methods. (NEDO)

Research and development of basic technologies for the next generation industries, 'bio-elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihtsu 'bio soshi'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed in order to establish basic technologies to realize new information processing incorporating high-order functions of living organisms, and bio-elements equipped with high-order functions. In the field of developing technical means to measure directly the information processing function of living organisms, detailed analysis has become possible for the first time on spatial operation of nerve activities by using two-dimensional beam measurement operation on the nerve activities. In the field of aiming at modeling, a system to realize functions effective in terms of engineering was structured by incorporating into the model the functions specific to nervous systems of visual sense and motion. In the field of element technologies, a large progress was seen in the basic technology and evaluation technology such as design and fabrication of molecules added with different functions in the LB membrane. Membranes having simple but different functions such as light beam and scent detection were manufactured, whereas a possibility of having them manifest functions as elements was verified. Furthermore, possibilities were discovered in manufacturing functional membranes by using self-organizing capability as a result of using basic properties possessed by polymers, and in realizing functions simulating plasticity of nerves. These achievements would lead to a belief that the targets of the first term research and development have been achieved nearly completely. (NEDO)

Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

Collection of outlines of Sunshine Program achievement reports for fiscal 1988. Solar energy (Light utilizing technology and heat utilizing technology); 1988 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-04-01

Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the experiment, refining, and verification of low-cost silicon; experiment, fabrication, and verification of solar panels; research on the practical application of high-efficiency crystal-based solar cells; research and development of amorphous solar cells; research and development of solar cell evaluation systems; development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and development of photothermal hybrid type photovoltaic power systems. Collected concerning heat-utilizing technologies are the research and development of solar thermal electric power generation systems; research and development of solar air-conditioners and hot water supply systems; and development of practical application technologies for industrial solar systems. Collected also are international cooperative projects on solar energy technologies. (NEDO)

Collection of outlines of Sunshine Program achievement reports for fiscal 1989. Solar energy (Light utilizing technology and heat utilizing technology); 1989 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-04-01

Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the research on the practical application of new-type solar cells; research on the practical application of amorphous solar cells; research and development of solar cell evaluation systems; research and development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and research and development of photothermal hybrid photovoltaic power systems. Collected concerning heat application technologies are the research and development of solar thermal energy systems; development of practical application technologies for solar systems for industrial use etc.; and cooperative projects between Japan and Australia etc. on solar energy technologies. (NEDO)

Changes of the temperature coefficients of the characteristics which accompany degradation and recovery of a-Si solar cells; A-Si taiyo denchi no hikari (denryu) rekka oyobi kaifuku ni tomonau tokusei ondo keisu no henka

Energy Technology Data Exchange (ETDEWEB)

Yanagisawa, T; Koyanagi, T; Nakamura, K; Takahisa, K; Kojima, T [electrotechnical Laboratory, Tsukuba (Japan)

1996-10-27

Pursuant to the measuring of temperature dependency of the characteristics such as conversion efficiency, during the process of degradation in a-Si solar cells due to light and electric current and the process of recovery by annealing, this paper describes changes in temperature coefficients, correlation between the characteristic parameters and the degradation, and the results of the examination of their characteristics. The conversion efficiency {mu} degraded approximately by 45% of the initial value each by the irradiation under a light intensity with 3 SUN accelerated and by the infusion of current at 20mA/cm{sup 2}; and then, the efficiency recovered to 70-75% of the degradation by subsequent annealing. In addition, in the temperature dependency at 80{degree}C against at 20{degree}C, Isc slightly increased while Vcc greatly decreased. This slight increase in Isc was mainly due to the decrease in the width of the forbidden band, while the decrease in Vcc was due to the increase in the reverse saturation current. The temperature dependency of {mu}N was negative, becoming small in accordance with the degradation. The temperature dependency of FF/FFO was negative initially both in light and current, but it decreased with the degradation and turned to positive. The temperature coefficients of I-V parameters reversibly changed corresponding to the degradation and recovery of these parameters and stayed in a good correlation. 7 refs., 8 figs., 1 tab.

Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on Si thin film crystal by particle acceleration growth); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Ryushi kasoku seichogata silicon usumaku kessho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-30

This research includes (1) basic study on formation technology of Si thin film crystals by particle acceleration growth, (2) basic study on junction formation technology for Si thin film crystals, and (3) basic study on GaAs compound semiconductors by pyrolysis method. In the 1st research, the thin film formation equipment was prepared for formation of charged Si particles from monosilane and solid Si in inert gas plasma by high-frequency excitation, and its expected characteristics were confirmed through its operation test. Basic data of Si thin films were also obtained by electron beam diffraction and Auger electron spectroscopy. In the 2nd research, study was made on junction formation systems for thin films, and the idea of a continuous thin film formation system was obtained for junction formation. In the 3rd research, development of p-type GaAs epitaxial technology was promoted, and it was confirmed that various p-type GaAs compound semiconductors of 10{sup 12}-10{sup 18}cm{sup -3} in impurity concentration are obtained by controlling a ratio of trimetylgallium gas to arsine gas. (NEDO)

Fiscal 1976 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on particle non-accelerating growth Si thin film crystal); 1976 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Ryushi hikasoku seichogata silicon usumaku kessho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This report describes the fiscal 1976 research result on production of Si thin film crystals and cell composition for photovoltaic power generation. In study on improvement of the crystallinity of polycrystal thin films by zone melting, flat recrystallized film was obtained by passing Si film through a high-frequency furnace at nearly 3mm/min in speed after growth of polycrystal Si film of 120-250{mu}m in thickness on a graphite substrate by gas-phase chemical reaction. In study on cell composition, as technology for forming electrodes on an uneven polycrystal surface with shallow junction, a Ti-Ag double layer method was developed in which junction characteristics are unaffected by heat treatment within 550 degrees C. On the photoelectric conversion efficiency of thin film cells, the efficiency of 5% and area of 10cm as targets in fiscal 1976 were attained by using a graphite substrate or polycrystal Si substrate. The thin film cell formed on an Si substrate could operate a small fan or a desk clock enough by scattered solar radiation. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on particle non-accelerating growth Si thin film crystal); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Ryushi hikasoku seichogata silicon usumaku kessho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-28

This research aims at development of the technology for producing photovoltaic power generation systems at a cost less than 1/100 of those by current technology. In fiscal 1974, basic study was made on formation technology of particle non-accelerating growth Si thin film crystals. In addition, evaluation was made on formed thin film crystal characteristics, and studies were also made on junction formation for thin film crystals, and on thin film formation and junction formation for indium phosphide compound semiconductor thin films. The research includes (1) study on formation technology for particle non-accelerating growth Si thin film crystals, (2) evaluation on Si thin film crystals, (3) study on junction formation technology for Si thin film crystals, and (4) study on indium phosphide compound semiconductors. Evaluations were made on thin film formation technology by CVD, and on crystallographical and electrical characteristics of the formed thin films. The evaluation results clarified the compatibility between substrates and Si thin films, the formation condition of columnar structure films, and the effect of growth conditions on a carrier density or mobility. (NEDO)

New Sunshine Project for fiscal 1997 on the international cooperation project. Cooperation in solar energy technologies among Japan, Australia and other countries; 1997 nendo new sunshine keikaku kokusai kyoryoku jigyo. Nichigo nado taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes the state of progress in the cooperation in solar energy technologies among Japan, Australia and other country, the memorandum concluded for the new project, and the activity report on the NEDO/MUERI project. The progress in the cooperation in solar energy technologies among Japan, Australia and other country is divided into that of the new project and that of the continued project. The former relates to the start of the long-term endurance test project for photovoltaic solar modules in Oman. The location of the endurance test is the Sultan Qaboos University in the suburb of Muscat. Modules subjected to the endurance test consist of ten modules of five types. The test will be performed on air temperature, humidity, wind directions, insolation on horizontal surface, insolation on slanted surface, ultraviolet ray intensity, module temperatures, and electric characteristics of the modules. The continued project is an outdoor endurance test for the photovoltaic solar modules begun in fiscal 1996, which is executed by the Murdock University Energy Research Institute (MUERI). The endurance test locations were selected at Darwin, Alice Springs and Perth. This paper reports the photovoltaic solar module endurance test and investigation, as well as the periodical consultations as the activity report of the NEDO/MUERI project. (NEDO)

Change of the equivalent circuit constants accompanied by the degradation and recovery of efficiency on a-Si solar cells; A-Si taiyo denchi no koritsu no rekka to kaifuku ni tomonau toka kairo teisu no henka

Energy Technology Data Exchange (ETDEWEB)

Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

1997-11-25

Investigations were given on how the equivalent circuit constants change when efficiency of amorphous silicon solar cells changes with time in light degradation and temperature recovery. In the experiment, light irradiation tests under a constant temperature and light intensity condition, followed by recovery tests under a constant temperature and constant weak light intensity or constant temperature condition were repeated continuously. According to the result of an experiment on single layer type cells, the change in each equivalent circuit constant in association with degradation in efficiency and file factor and variation in recovery is reversible mostly. However, a slightly irreversible component was recognized only in the initial degradation process in series resistance and diode factor values. With regard to stacked cells, it was suggested that the main players to determine cell characteristics during the processes of deterioration and recovery take turns among the three layers as follows: the shape of the time-based change in the efficiency comes different and is not saturating; as the efficiency decreases, the extent of the change increases in the diode factor and series resistance; and the path the deterioration takes differs from that the recovery takes. 2 refs., 12 figs.

Simulation study on reduction of peak power demand and energy consumption in residential houses with solar thermal and PV systems; Taiyo energy riyo jutaku no fuka heijunka oyobi energy sakugen koka no simulation ni yoru kento

Energy Technology Data Exchange (ETDEWEB)

Endo, T. [Yokohama City Office, Yokohama (Japan); Udagawa, M. [Kogakuin Univ., Tokyo (Japan). Faculty of Engineering

1995-11-20

In this study, taking the all factors involved in the energy consumption in residential houses as subjects, the effectiveness of the solar PV system and solar thermal utilizing system in residential houses has been studied by simulating a model residential house considering the improvement of the residual environment in the future. Therefore, a model residual house is assumed, 18 kinds of combinations of construction style, cooling and heating type and solar energy utilizing form are assumed and year round simulation is carried out. The conclusions obtained by the simulation are as follows. The energy consumption in residential houses may decrease greatly by using a solar hot water supplying system. If combined with a solar PV system, the energy consumption in one year is about 8.7 to 9.7 MWh. The combined use of a solar thermal utilizing system and a PV system is more effective to reduce the second-time energy in comparison with the PV system only. 36% of the space heating energy consumption may be decreased by using the solar space heating system, but the decrease effect of the energy consumption of the solar space heating system is smaller than the solar hot water supplying system. 12 refs., 26 figs., 3 tabs.

Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (dainiki kenkyu kaihatsu hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The research and development in the second term included development of raw materials, elucidation of electricity conduction mechanism, and development of methods to improve stability and a new processing method. Crystals of a large number of charge migrating complexes were grown to elucidate their electron properties and structures. A theoretical model was structured for the superconduction mechanism in the charge migrating complexes. Poly-p-phenylene vinylene-based polymers achieved {sigma}=1.1 times 10{sup 4}s/cm as a result of extension of soluble reaction intermediates. Poly-2, 5-phenylene vinylene doped with FeCl{sub 3} retained 10{sup 3}s/m for 165 days in nitrogen. Polypyrrole achieved 3.0 times 10{sup 3}s/cm in constant potential electrolytically oxidizing polymerization and extension at low temperatures. Polypyrrole doped with ClO{sub 4}{sup -} retained electric conductivity of 85% for 400 days in nitrogen. Electric conductivity of higher than 10{sup 5}s/cm was obtained by applying different kinds of doping into thin film and fiber formed graphite. The world's highest conductivity of 9 times 10{sup 5}s/cm was achieved particularly with discharge laminated and polymerized graphite doped with AsF{sub 5}. (NEDO)

Estimation of site effects in Higashinada Ward, Kobe City using aftershock records of the 1995 Hyogo-Ken Nanbu Earthquake; Hyogoken nanbu jishin no yoshin kiroku wo mochiita Kobeshihigashinadaku no jiban zofuku tokusei no hyoka

Energy Technology Data Exchange (ETDEWEB)

Kurita, K.; Yamanaka, H.; Seo, K. [Tokyo Inst. of Tech. (Japan)

1998-07-30

Source spectra and site effects are separated using the aftershock records, and the characteristics of short period earthquake motion in Higashinada Ward, Kobe City including the area to the south of seismic intensity 7 area are investigated placing emphasis on how far the site effects can be explained by 1-D ground structure. The shape and amplitude of the site effect of KNN and KYC located outside the seismic intensity 7 area can be explained fairly well by 1-D multiple reflection theory of S wave. However, peaks near 3 to 4Hz of KNN and UOZ in seismic intensity 7 area can not be explained. This suggests that the site effects of seismic intensity 7 area obtained by the aftershock records might include 2-D effects of underground structure. Inversion is performed using site effects as the objective functions to determine S wave velocity structure and Qs in the sedimentary layer. S wave velocity structure shows no systematical difference from those of the past models. 22 refs., 13 figs., 2 tabs.

Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

Research and development of the industrial basic techniques of the next generation. Composite materials (Final research and development evaluation / Part 1); Jisedai dangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (Saishu kenkyu kaihatsu hyoka 1)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

This R and D project is aimed at development of highly functional materials for aerospace devices, bringing into focus research and development of resin-based composite materials (FRPs), metal-based composite materials (FRMs), and evaluation of their properties and their design techniques. The basic target properties are heat resistance temperature of 250 degrees C or higher and tensile strength of 240 kg/mm{sup 2} or more for the FRPs, and heat resistance temperature of 450 degrees C or higher and tensile strength of 150 kgf/mm{sup 2} or more for the FRMs. This R and D program has been implemented for 8 years for development of raw materials, molding/processing techniques, quality evaluation and designs through information exchange and discussions of the experts in each area under integrated, close cooperation from raw materials to molding/processing. Most of the data indicate that the target properties and objects are satisfied or exceeded. It is therefore concluded that this project for the composite materials, extending for 8 years in 3 phases, has sufficiently achieved the initial objects. The unique techniques are incorporated in the raw materials, molding/processing processes, quality evaluation and designs. These efforts have produced the FRPs and FRMs of the world highest qualities. (NEDO)

WE-NET substask 3. Conceptual design of total system (Safety measures and evaluation techniques); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 3. Zentai system gainen sekkei anzen taisaku hyoka gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work) in fiscal 1998, researches and studies were conducted to clearly define safety designs and to improve on accident-and-safety analyses. In relation with system safety design, investigations continued into Japanese and foreign manuals and regulations about the handling of hydrogen and its peripherals, and safe design guidelines (draft) were compiled. Anomalies and accidents supposed to be typical of each of the systems concerned were investigated. As for accident-and-safety analyses, incorporation of a turbulence model was studied in relation to models representing the leak, evaporation, and diffusion of liquid hydrogen, and improvement was achieved when the scope of evaluation was enlarged concerning the hydrogen detonation model. The integration of the two models was discussed for the due evaluation of a series of processes of liquid hydrogen leak, evaporation, diffusion, and detonation. Calculation was performed for two assumed accidents, and the results were found to justify the integration of the two models. (NEDO)

FY1995 comprehensive assessments of measures mitigating heat island phenomena in urban areas; 1995 nendo heat shinku wo riyoshita daikibo reibo system no kaihatsu (daitoshi ni okeru kaki koonka taisaku gijutsu no hyoka shuho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The urban heat-island phenomenon is one of the man-made changes of local climate. The objectives of this research are to develop a heat-island model to cover the building scale to mesoscale and to assess the countermeasures to heat- island effects. The analysis of Tokyo by remote-sensing, field observation and estimates of anthropogenically exhausted heat using energy consumption data were conducted. And, techniques to assess the most effective countermeasure against the urban warming were developed. (NEDO)

Fiscal 1999 survey report. Project of promoting international cooperation on global environments/Project of assessing climate change impacts; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo chosa hokokusho. Kiko hendo eikyo hyoka nado jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As part of international cooperation concerning global warming, an assessment is conducted of climate change mitigating measures, from the viewpoints of technology, environment, economy, and community, in coordination with the IPCC (Intergovernmental Panel on Climate Change) 3rd working group responsible for energy policy and technological development. It aims to contribute to the preparation of a 3rd assessment report, and covers (1) the development of an assessment technique relating to cost analysis, (2) problems in the transfer of technology and solutions for them, and (3) the assessment of various policy options. Under item (1), studies are made about modelling techniques, common parameters and their values, potentials for effect, control of warming, etc. Under item (2), factors impeding the transfer and diffusion of technology are extracted and solutions therefor and the establishment of new incentives are deliberated, with analysis and investigation focused on tasks and solutions for furthering global transfer of technology with attention paid to various specific cases. Under item (3), concrete and feasible policy options are discussed on the basis of the outcome of the above-named endeavors, in view of characteristics of each of the regions, departments, and techniques. (NEDO)

Equivalent CTOD concept based on the local approach and its application to fracture performance evaluation of welded joints; Local approach ni motozuku toka CTOD gainen no teian to tsugite hakai seino hyoka eno oyo

Energy Technology Data Exchange (ETDEWEB)

Ohata, M.; Minami, F.; Toyoda, M. [Osaka University, Osaka (Japan). Faculty of Engineering; Tanaka, T.; Arimochi, K. [Sumitomo Metal Industries, Ltd., Osaka (Japan); Glover, A. [Nova Gas Transmission Ltd., Calgary (Canada); North, T. [University of Toronto (Canada)

1996-12-31

A proposal was given on an equivalent crack tip opening displacement (CTOD) concept which relates quantitatively fracture performance of a structural member with the result of a three-point bending CTOD test via the Weibull stress based on a local approach. The equivalent CTOD is defined as a CTOD in which a three-point CTOD test piece and a structural member provide the same Weibull stress. Experimental and analytical discussions were performed on X80 steel welded joints. Effectiveness of the equivalent CTOD concept was verified from the fact that the fracture performance in welded joints with a large width estimated from the result of the three-point bending CTOD test using the equivalent CTOD concept showed good correspondence with the fracture performance obtained in the experiments. On the other hand, the result of estimation using the conventional CTOD concept is considerably smaller than measurements. As an application of the equivalent CTOD concept, a new determination procedure was introduced on required fracture tenacity to ensure deformation performance required on structural elements. The required CTOD value shows a trend that the smaller the ratio of yield stress of the welded metals to that in the base material, the greater the required CTOD grows. 16 refs., 19 figs., 3 tabs.

Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

Achievement report on research and development (1st phase) of direct iron making by use of high-temperature; Koon kangen gas riyo ni yoru chokusetsu seitetsu no kenkyu kaihatsu (daiikki) ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-02-01

Efforts are put into the study of direct iron making for use in a closed system where heat energy from a multi-purpose high-temperature gas furnace expected to be developed in the near future will be utilized for iron making. The researches, carried out for the establishment of technologies necessary for designing, building, and operating a pilot plant dimensionally suitable for connection to a 50MWt multi-purpose high-temperature gas furnace, cover the plant total system, a high-temperature heat exchanger, ultrahigh-temperature alloys, high-temperature insulating materials, a reduced gas generating unit, and a reduced iron making unit. When the effort is evaluated as a whole, it is found that the newly developed system is effective in preventing pollution, emitting but 0.1Nm{sup 3} of SOx per 1 ton of crude iron against the 0.4-0.9Nm{sup 3} emitted by a blast furnace/converter iron making mill. It is also found effective in reducing fossil fuel dependence and in enhancing energy source diversification. When it comes to energy conversion efficiency, furthermore, it is shown that the new system achieves a rate of 60% or more while only approximately 30% is attained by light water reactor power generation and approximately 40% by a high-temperature gas furnace. (NEDO)

Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

Equivalent CTOD concept based on the local approach and its application to fracture performance evaluation of welded joints; Local approach ni motozuku toka CTOD gainen no teian to tsugite hakai seino hyoka eno oyo

Energy Technology Data Exchange (ETDEWEB)

Ohata, M; Minami, F; Toyoda, M [Osaka University, Osaka (Japan). Faculty of Engineering; Tanaka, T; Arimochi, K [Sumitomo Metal Industries, Ltd., Osaka (Japan); Glover, A [Nova Gas Transmission Ltd., Calgary (Canada); North, T [University of Toronto (Canada)

1997-12-31

A proposal was given on an equivalent crack tip opening displacement (CTOD) concept which relates quantitatively fracture performance of a structural member with the result of a three-point bending CTOD test via the Weibull stress based on a local approach. The equivalent CTOD is defined as a CTOD in which a three-point CTOD test piece and a structural member provide the same Weibull stress. Experimental and analytical discussions were performed on X80 steel welded joints. Effectiveness of the equivalent CTOD concept was verified from the fact that the fracture performance in welded joints with a large width estimated from the result of the three-point bending CTOD test using the equivalent CTOD concept showed good correspondence with the fracture performance obtained in the experiments. On the other hand, the result of estimation using the conventional CTOD concept is considerably smaller than measurements. As an application of the equivalent CTOD concept, a new determination procedure was introduced on required fracture tenacity to ensure deformation performance required on structural elements. The required CTOD value shows a trend that the smaller the ratio of yield stress of the welded metals to that in the base material, the greater the required CTOD grows. 16 refs., 19 figs., 3 tabs.

Fiscal 1974 Sunshine Project result report. R and D on solar energy system (weather survey). Part 2. Guideline for using weather data; 1974 nendo kisho data ni saishite no shishin. 2. Taiyo energy system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

This report describes the guideline for using weather data in R and D on solar energy system. Solar radiation is defined as direct, scattered and reflected radiation in a range of near UV-near IR radiation. Direct solar radiation is observed by silver disk pyrheliometer, while global solar radiation by thermostat or bimetal pyranometer. Accuracy standards of such meters are indispensable to keep the accuracy uniformly. To keep the uniformity and accuracy of observation data all over the world, the international comparative observation is held every 5 years. Solar radiation observation in Japan started in 1932 by installing silver disk pyrheliometers all over the country. In 1938 the observation stations were increased to 79 sites, however, in 1953 those were integrated into 13 long-term weather observation stations. Sunshine duration is defined as the time direct sunbeam aims at the ground, and observed generally by Jordan's heliograph which observes sunshine durations with burned holes on photosensitive recording paper by direct sunbeam through 2 small holes on both sides of a cylinder. The history of statistical processing of solar radiation and sunshine duration data in Meteorological Agency is also presented. (NEDO)

Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

Fiscal 1999 research report. Data acquisition and analysis on the advanced high-efficiency energy system field test; 1999 nendo sendoteki kokoritsu energy system field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Although the next-generation phosphoric acid fuel cell has nearly reached its practical application stage as far as technology is concerned, its diffusion is yet to come due to lack of data about its cost efficiency and reliability. Under the circumstances, the goal now is to collect and analyze various data obtained in the above-named project which was started in fiscal 1997 for the compilation of data useful for full-scale diffusion in the future so that a foundation may be built for the overall popularization of the fuel cell. In this fiscal year, assessment and analysis have been conducted at 15 test sites now in presence. At the second plant of the Semboku LNG Terminals where approximately 17,000 hours have elapsed since the test began, the cell has operated for more than 16,000 hours in total. The Mycal Bore Sanda has established the longest uninterrupted operation record of 6,500. As for power generation efficiency, a town gas 13A-fueled system exhibits approximately 40% operating smoothly at a high overall efficiency of not less than 90%. (NEDO)

Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly crystalline polymeric material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo saishu kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-01

Basic technologies are developed involving highly crystalline polymeric materials comparable to metals in dynamic property even when used singly. The aim is to expand the application scope of polymeric materials including those designed as structural materials so that their light weight, high resistance to corrosion, and excellent machinability may be utilized in various fields. Target performance includes an elastic modulus under bending force of 100GPa or more in anisotropic materials and 50GPa or more in isotropic materials, a linear expansion coefficient of 5 times 10{sup -5}/degrees C or less, and a thermal deformation temperature of 180 degrees C or more. Tasks faced in relation to film or molded articles of anisotropic materials are the rigid molecular design, molding method including molecular orientation control, and molecular complex technology; and, in isotropic materials, the strengthening of interaction between molecules, establishment of molding methods, and equipping materials with high machinability. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. To be mentioned are achievements involving the generation of multidimensionally bound diacetylene polymeric crystals, higher elastic modulus and moldability provided to polyarylate materials, magnetic field orientation, ultrahigh-elasticity layered body, and organic-inorganic ionically bonded complex material, etc. (NEDO)

Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the mechanism of light deterioration reaction of photochromic molecules, it was disclosed that 6-nitrospirobenzopyran has the light deterioration caused from the excitation triplet state. This disclosure presents a possibility of preventing the light deterioration. New derivatives that show photochromism were synthesized, and thin films were produced by using the LB process. This indicates a possibility of producing the photochromic materials as the high multiplex recording material. With regard to PHB materials, an evaluation technology having spectrum resolution of the world's highest level was established and measurements were performed. Hole formation was verified for the first time in the world at the temperature higher than the liquid nitrogen temperature by using a PHB material of ionic porphin/polyvinyl alcohol systems. This verification indicates a feasibility of practically usable PHB materials. (NEDO)

Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research and survey for development of solar cell of new power generation device structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Attention is paid to behavior at the molecular level with reference taken to the photosynthetic mechanism, and a behavioral mechanism is proposed, which incorporates, in place of the conventional band model, a concept of a molecular structure based on electron transfer, excitation energy transfer, and reactions of oxidation and reduction. Discussion is then made on elements of technology development for the embodiment of high-efficiency organic ferroelectric thin-film solar cells. The elements taken up include the feasibility of organic ferroelectric thin-film cells, photoelctric conversion systems of plants and photosynthetic bacteria, solar cells using donor-acceptor type dyes, organic thin-film solar cells using conductive polymers, and efficient photoexcitation of organic dyes. Fullerene compounds are semiconductive and their band gaps may be controlled to stay within the range of 0.75-1.9eV, and this justifies a hope that they will serve as solar cells. As for TPV (thermophotovoltaic) conversion, it is under development mainly at NASA (National Aeronautics and Space Administration) as a transportable power source based on heat of combustion. Efforts are also being exerted since 1990 in five European countries to develop TPV systems for small-scale cogeneration. (NEDO)

FY 1977 Annual report on Sunshine Project results. Research and development of photovoltaic power generation systems (Research and development of particle nonacceleration growth type silicon thin-film crystals); 1977 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Ryushi hikasoku seichogata silicon usumaku kessho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-01

As part of the research and development project for producing photovoltaic power generation systems at reduced cost, the R and D efforts are made for producing particle nonacceleration growth type silicon thin-film crystals. The research items are (1) research on thin-film crystals, and (2) research on cell-structuring method. The item (1) studies quantities, types and electrical properties of impurities and crystal defects in the polycrystalline ingots, produced by the Czochralski method from metal grade silicon and purified metal grade silicon stocks. Next, the substrate prepared above is coated with a thin film of silicon by the vapor-phase growth method with dichlorosilane as the source, to evaluate the thin-film crystals by measuring the crystal defects and lifetime of small numbers of carriers. The item (2) studies the effects of the solder dipping method. In addition, unevenness of photoelectric current is analyzed by a laser scanning microscope, to investigate the effects of the secondary impurities and crystal defects in the substrate crystals on photoelectric current. As a result, it is found that conversion efficiency is improved by grading the hole concentration in the p-type activated layer. The targets of 10 to 20 m{sup 2} as the area and 7 to 8% as the conversion efficiency are attained by preparing the crystals again. (NEDO)

FY 1997 report on the study on lamination control technology for functional multi-element oxide thin films by complex beam epitaxy (CxBE) process; 1997 nendo chosa hokokusho (sakutaisen epitaxy (CxBE) ho ni yoru kinosei tagenso sankabutsu usumaku no sekiso seigyo gijutsu ni kansuru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Complex beam epitaxy (CxBE) process was proposed and demonstrated as new deposition process of multi-element oxide thin films. This process radiates excimer laser onto a metal complex target of ethylenediamine-tetraacetate complex under reduced pressure oxygen atmosphere condition in a reaction vessel to supply raw material onto a heated substrate. This process allowed deposition of YBCO123 phase hetero-epitaxial film onto a single-crystalline SrTiO3 substrate. This process was proved to be promising through study on crystal orientation, composition transcription and surface smoothness of the obtained oxide thin films. In addition, epitaxial ZnO film was also deposited onto a single crystalline Al2O3 substrate by this process. The relation between the obtained film and substrate epitaxy was examined, and photoluminescence of specimens was measured by triple wave of Nd:YAG laser. As a result, it was clarified that the epitaxial ZnO film prepared by this process is useful as laser material. 60 refs., 48 figs., 5 tabs.

Report on 1979 result of Sunshine Project. R and D on solar power generation system (R and D on particle non-accelerated growth type silicon thin film crystal); 1979 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Ryushi hikasoku seichogata silicon usumaku kessho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

The R and D was intended to establish the manufacturing technology of a particle non-accelerated growth type silicon thin film crystal, for the purpose of developing a technology for enabling the production of a solar power generation system, whose price is practically 1/100 compared with that of building the system with the current technology, and the R and D was also intended to build the system using such silicon material. While a simple purification method was examined for a low purity metallurgical-grade silicon, a solar-grade silicon (SOG) was developed as the new material this year, with a solar cell experimentally manufactured having a structure directly joined to the substrate material and with evaluation carried out on the characteristic of such solar cell. The application of 'gettering' was tried which was for removing harmful impurities from the substrate obtained from such material, bringing an outlook of manufacturing a solar cell with a conversion efficiency of 10%. Concerning the SOG-Si, the efficiency of 13% or higher was attained through the improvement of the manufacturing process. This was the value comparable to the case of using a conventional high purity monocrystal wafer. Further, the application of an ion implantation method was studied for the purpose of getting a low cost. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. Separate volume. R and D of the system evaluation technology (Data book on the photovoltaic power system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu (Bessatsu : Taiyoko hatsuden system data shu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of establishing the optimum design and optimum operation technology of various kinds of photovoltaic power system, data were collected to make a data book on various kinds of photovoltaic power system of which the future commercialization is expected. Included in this data book were the monthly report on operation data on demonstrative test facilities at the Hamamatsu site of JQA (Japan Quality Assurance Organization), daily graph of insolation/temperature, monthly graph of wind direction/wind velocity. Further, as the data on the residential use photovoltaic power system, data on the following were summed up: information on the site of installation of the residential use photovoltaic power system (photo information, the state of installation such as sites installed more in FY 2000, drawings of module arrangement and measuring point layout, etc.), daily report on operation (graph of daily trends, daily report by site, hourly report by site, daily report on all sites, hourly report on all sites), operation data and performance indices, list of troubles arising in the residential use photovoltaic power system, other system information about residential use measuring data, power generation characteristics and {alpha}{sub pmax} of residential use solar cell modules, etc. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cells); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-27

This report summarizes the fiscal 1974 research result on R and D of new type solar cells, which includes researches on (1) solar cell structure, (2) packaging, and (3) improvement of a conversion efficiency. In the 1st research, theoretical study was made on the relation between a solar cell efficiency and various design factors to obtain basic data for ordinary cell structure and vertical junction type cell structure. As impurity source, a thermal diffusion method using doped oxide by CVD was compared with that using boron nitride, resulting in no difference in solar cell characteristics between both methods. The measurement results on contact resistances of Al, Fe and Ni with electrodes prepared by electron beam deposition showed that these materials are applicable to Si more than 10{sup 18}/cm{sup 3} in impurity density as electrode materials. In the 2nd research, exposure tests were made on some kinds of specimens, resulting in no troubles. Study was made on production costs and structures suitable for automatic production of 4 kinds of packages with different basic structures. In the 3rd research, the prototype solar cell was prepared to use under solar radiation within 20SUNS. (NEDO)

Fiscal 1976 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cell); 1976 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-05-30

This report describes the fiscal 1976 research result on new type solar cells for photovoltaic power systems. On junction formation, the solar cell fabricated by spray coating showed output characteristics equivalent to that by rotary coating or phase diffusion, and inexpensive coating liquid, 1/40 of commercially available liquid in price, showed a sufficient result, however, the conversion efficiency of P{sup +}/N elements was insufficient. Schottky barrier polycrystal Si thin film was suitable for large-area elements without any property degradation. Small grain boundary density of polycrystal layers was also necessary. Temperature characteristics of collector element structure with a comb electrode were calculated theoretically. Change in diffusion length of minority carriers due to temperature well agreed between measured and calculated ones. Optimization calculation was also carried out. The size, curve, weight and transmissivity of plastic and glass materials for solar cell packaging were evaluated by continuous outdoor exposure tests. Fluorinated ethylene-propylene, methyl methacrylate and polycarbonate plates and glass were the most promising materials because of less deformation. (NEDO)

Research and development of the industrial basic technologies of the next generation, 'composite materials (fine ceramics)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fine ceramics'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-30

The results of the first phase research and development project for developing fine ceramics as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop fine ceramics of high strength, corrosion resistance, precision and wear resistance, noting their excellent characteristics. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at development of silicon nitride and silicon carbide for synthesis of the stock materials; explosive forming/treating the stock powders; forming, sintering and processing/joining; evaluation of the characteristics; non-destructive testing methods; designs; and evaluation of the parts, among others, as the elementary techniques for production, evaluation and application of the fine ceramic materials. The technical targets of improving functions have been achieved, or bright prospects have been obtained therefor in development of the techniques for synthesis of the stock materials, forming/sintering and processing/joining. The silica reduction for stock synthesis, basic techniques for molding/sintering, and rheological considerations for the molding/sintering techniques represent the techniques of the next generation, because they break through the limitations of the conventional techniques. (NEDO)

Research and development of the industrial basic technologies of the next generation, 'composite materials (resin-based)'. Evaluation of the second phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (jushikei). Dainiki hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-31

The results of the second phase research and development project for developing the resin-based composite materials as the basic technologies of the next generation are evaluated. The second phase (FY 1983 to 1986) project is carried out to achieve the objectives, which are set up based on the objectives for the basic designs and the results of the first phase project. As a result, the concrete (promotion objectives), including those related to mechanical characteristics, have been almost achieved. For development of the highly functional FRP materials, the R and D efforts are directed to improvement of their moldability while satisfying the requirements of high functions, e.g., resistance to heat, leading to development of the basic techniques for epoxy resin-based intermediate materials. These results indicate possibility of commercialization of highly heat-resistant polyimde resin-based and novel resin-based intermediate materials. The results of the novel molding/processing methods, taken up in the second phase project as the ones which use no autoclave, are rated that they are developed to suggest possibility of the eventual commercialization, although the products they give are not always showing sufficient mechanical properties. (NEDO)

Report on evaluation of research and development of direct steel-making using high-temperature reducing gas. Phase 1. Draft; Koon kangen gas riyo ni yoru chokusetsu seitetsu no kenkyu kaihatsu (daiikki) ni kansuru hyoka hokokusho (an)

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-01-01

Described herein is development of direct steel-making using high-temperature reducing gas. A light hydrocarbon fraction (boiling point: 230 degrees C or lower), produced by steam cracking of vacuum residua, is reformed into a reducing gas in the presence of steam, using heat to be supplied by a nuclear plant which produces high-temperature gases for various purposes. This reducing gas is then supplied to a plant for producing reduced iron. This project has established basic techniques for designing, constructing and operating a direct steel-making pilot plant, to be connected to a 50 MWt high-temperature gas test furnace. The closed iron-making system and greatly reduced SOx emissions to several fractions of the current level are some of the expected effects. The environmental impacts of the high-temperature gas furnace will be on a level with those associated with a light-water reactor. Cracking and gasification of vacuum residua, which has found limited purposes so far, should expand its applicable areas and reduce dependence on fossil resources, leading to diversification of energy sources. The overall thermal efficiency of the high-temperature gas furnace is expected to increase to at least 60%, because its high-temperature gases of around 1,000 degrees C can be used for heating processes, and the waste heat can be further used for generation of steam for power production. (NEDO)

Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'Taikankyo kyoka soshi'. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-31

In the research and development of the environment resistance strengthened elements with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments, the second term has developed an integration technology and its evaluation technology based on the achievements in the first term. In developing the heat resistant element technology, the technology to grow {beta}-SiC crystals was expanded to obtaining thin film crystals with high migratory performance by using higher temperatures. At the same time, development was performed on a technology to manufacture multiple number of transistors on one substrate, such as the doping technology and etching technology. Using this technology, schottky diodes and p-n junction elements being the basic structures of MES-FET and bipolar transistors were fabricated. In the evaluation and testing technology, the {gamma} dose measuring method using TLD was improved, the traceability of {gamma} ray irradiation amount was assured, the simplified irradiation testing method using X-ray was established, and the heat resistance testing technology for electronic parts was established. Furthermore, attempts were made on enhancing radiation resistance of the elements, such as in MOS silicon integrated circuit, bipolar silicon integrated circuit, and compound semiconductor integrated circuit. (NEDO)

Research and development of basic technologies for next-generation industry. Evaluation of 1st-phase research and development of 3-dimensional circuit devices; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Sanjigen kairo soshi daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The aim is to develop basic technologies relating to 3-dimensional circuit devices with an ultrahigh-density accumulation of functions therein for the embodiment of ultra-small high-performance data processing devices or artificial brain-like multiple-function data processing devices. To be developed are laminate-structure devices which have an ultrahigh-density accumulation of logic and memory functions or a complex accumulation of functions including signal and sensor functions. In the 1st phase, importance is attached to the development of a multilayer crystalline structure, which is the most elementary in the development of 3-dimensional circuit devices, and of processing technologies for them. Propositions are made and analyses are conducted relating to the enlargement of exposure region in synchrotron radiation lithography, development of a maskless beam process of a resolution of 0.1{mu}m, development of a focused ion beam device, etc. Recrystallization methods using a laser beam or a linear electron beam are developed for the growth of multilayer crystals, and are proved to be effective. The application feasibility of a flat deposition dry process etc. to laminate processing technologies is demonstrated. Concerning integration technologies, some laminated circuit devices are experimentally fabricated, and their behavior is determined. The goals of the 1st phase are found achieved. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of methods for testing and evaluating pure titanium; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Jun titan no shiken hyoka hoho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of submitting propositions to ISO (International Organization for Standardization)/TC79 (Light metals and their alloys) and ISO/TC135 (Non-destructive testing), studies were made relating to the standardization of methods for chemical ingredient analysis and non-destructive testing of industrial pure titanium. In the development of an ingredient analysis method for pure titanium, performance standards and analytical allowance were determined for an inductively coupled plasma emission spectrochemical analyzer for vanadium, niobium, cobalt, and boron, which were short of completion in the preceding fiscal year. As for spark discharge emission spectrochemical analysis, analysis methods were newly established for oxygen and hydrogen. In the development of optical flaw detection for pure titanium boards, the quality of test pieces were determined by use of a reference test piece, and studies were made about the kinds of artificially produced flaws and a method for sensitivity calibration. In the development of ultrasonic flaw detection for pure titanium boards, studies were made about the effects of board thickness, kinds of flaws, and of board size. Using the findings, a draft standard was prepared in Japanese for a JIS (Japanese Industrial Standards) proposition and another in English for an ISO proposition. (NEDO)

FY1992 research report on the evaluation and analysis of data collected in fuel cell power generation field test project; 1992 nendo nenryo denchi hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the achievements in fiscal 1992 in the field tests on fuel cell power generation systems. The three locations subjected to the present analysis are all installed with 50-kW systems, whereas power generation efficiency of around 35% such as 35.3, 34.2 and 34.6% was obtained when the systems were operated at the rated output. When the load gets to below a certain load band (about 30 kW), the power generation efficiency decreases proportionately with the load. The overall efficiency including heat supply was 77.8, 70.7 and 80.3% respectively at about the rated output, showing a trend that the higher the thermal efficiency, the higher the overall efficiency. The case of generating both electric power and heat simultaneously has higher efficiency than the case of heat supply alone. The contribution rate of the fuel cell as a base load was 2.8, 4.6 and 13.6%, respectively. The system with as high value as 13.6% takes a power load following type operation mode, in which power is generated during a time band with large load during weekdays, and no power is generated at nighttime and in holidays when load is smaller, playing a role of peak responding power supply. Only one trouble has occurred in an auxiliary generator in the heat recovery system. (NEDO)

Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'taikankyo kyoka soshi'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-30

Research, development and evaluation were performed with an objective of developing environment resistance strengthened elements, with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments. The objective for the first term is to develop the basic technology on element structures required to raise the environment resistance, and the methods of testing them. With regard to heat resistant elements, {beta}-SiC single crystal thin films were formed, and a prospect was obtained on using them as the elements. Regarding MOS integrated circuit, bipolar integrated circuit, and GaAs element, points presenting the largest issue in radiation resistance were noticed according to respective elements. Thus, temperature for gate oxide film formation was lowered, element structures were improved, and gate lengths were decreased to enhance the radiation resistance. For the evaluation test technology, a provisional testing method was prepared for the radiation resistance, a prototype in-situ irradiation testing device was fabricated and so was a prototype high-temperature testing device usable up to 500 degrees C. These achievements lead to a belief that the targets for the first term have been achieved. (NEDO)

Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

Report on a survey in fiscal 1999. Survey on the actual state of utilizing unified evaluation models for global warming; 1999 nendo chikyu ondanka ni kansuru togo hyoka model no katsuyo jittai ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The present survey is intended to compare and analyze major unified global warming evaluation models available inside and outside the country, and analyze the directionality on supports for the future model developments that will be performed by the Ministry of International Trade and Industry. The report describes in Section 1 how the summaries of the global warming evaluation models may be put into order. A unified evaluation model may be positioned basically as a platform to unify the processes of recognizing scientific problems and the processes of determining the policies. Section 2 describes how the summaries of the major global warming evaluation models may be put into order. The models include the followings: DNE21 (Dynamic New Earth 21), GRAPE model, AIM model, MESSAGE (IIASA) model, IMAGE2 (RIVM), and GREEN (Gene Ral Equilibrium Environment)(OECD). Section 3 summarizes the purposes, general situation of development, scope of the objects, and technological features as the features of each model. Section 4 describes the analysis of the actual state of utilizing unified evaluation models for global warming. The results of the analysis were put into order in a map form to make clear the positioning of the major models that have been put into order. (NEDO)

FY 1998 evaluation/analysis of the data collected in the field test project for photovoltaic power generation for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the field test project for the photovoltaic power generation for public facilities, operational data were collected/analyzed on facilities at 158 sites installed from FY 1994 to FY 1997. As a result, the following were found out: Average values of the global radiation on an inclined surface, equivalent array operation time, equivalent system operation time, system operation time, inverter performance efficiency, inverter load factor, array power coefficient, and system power coefficient are 3.51 kWh/m{sup 2}/D, 2.72 h/D, 2.47 h/D, 10.3 h/D, 0.91, 0.30, 0.77 and 0.70, respectively. No deterioration with age was recognized in the 4-year operation data. As to the maintenance, the item, 'there are a lot of failures in the photovoltaic power system,' was 2% in rate. As to the inspection, times are mostly once a month. The annual maintenance cost was widely between about 360 yen/kW and about 30,000 yen/kW. Supposing annual expenses to be a total of capital expense, direct expense, and general administrative expense, the power generation cost dropped from approximately 240 yen/kWh in FY 1994 to 100 yen/kWh in FY 1997. (NEDO)

Annual cycle solar energy utilization with seasonal storage. Part 8. Study on periodic steady state of the annual cycle energy system at a practical operation; Kisetsukan chikunetsu ni yoru nenkan cycle taiyo energy riyo system ni kansuru kenkyu. 8

Energy Technology Data Exchange (ETDEWEB)

Tanaka, H; Okumiya, M [Nagoya University, Nagoya (Japan)

1997-11-25

A study was made of the periodic steady state of the annual cycle solar energy system with seasonal heat storage at a practical operation. Cold heat in winter and warm heat in summer are stored in the seasonal storage tank, and these are each used in shift until when demand for cold/warm heat appears. Moreover, gap in quantity of cold/warm heat going in/out of the heat storage tank during a year is filled by natural energy such as solar energy, so that the system can be operated in annual cycles. Studies were conducted of the periodic unsteady term and the problem on lowering of performance during the term such as the periodic unsteady term of water temperature inside the seasonal heat storage tank and temperature of the soil around the storage tank, and the level of lowering of performance during the term, necessity of additional operation/control at the start of operation and aged deterioration of the system. Within the assumption, even if starting operation in any time of the year, the system could show the performance almost expected from the first operation year with no additional system operation and control required only at the start of operation. It is thought that the heat source selection control of heat pump largely contributes to this. 4 refs., 5 figs., 3 tabs.

Museum of water, green and the sun - Marumori. New energy vision of the Marumori Town area; 2001 nendo Marumori machi shin energy vision hokokusho. Chiiki shin energy vision sakutei tou jigyo (Mizu to midori nto taiyo no hakubutsukan Marumori)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

In Marumori Town, Miyagi Prefecture, a 'new energy vision of the area' was worked out which indicated the assessment of the energy reserved in the town and the course of new energy to be determined in the future. The energy consumption amount of Marumori Town in FY 1999 was estimated at 47,535 kL in crude oil conversion. By sector, the energy consumption amount was the largest in the order of the industrial sector, the transportation sector and the commercial/residential sector. The availability of new energy in Maruyama Town was estimated at approximately 480,585 GJ, of which the solar energy utilization was the largest, 53.1%. The photovoltaic power generation was the next largest, 25.4%, followed by the temperature difference energy (underground water), 8.9%, clean energy car, 7.8%, etc. As a plan for the first introduction of new energy, the following were studied: introduction of photovoltaic power generation facilities to the Marumori Town Office, introduction of new energy to public facilities around the Fudoson Park, introduction of wind power generation facilities to the town-run pasture, construction of the Marumori-type biogas plant, construction of a mini hydroelectric power plant, introduction of clean energy car to public vehicles, introduction of new energy facilities to the area of Kawa-no-Eki (station of the river), etc. (NEDO)

Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzokukei)'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-31

The results of the first phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to understanding the basic characteristics regarding wettability and reactivity of PAN-based carbon fibers and PCS-based silicon carbide fibers with metals, in which aluminum-based matrices are considered; preliminary tests for various composting methods; and development of wire preforms as the intermediate materials. Bright prospects have been obtained for improving problems involved in each technique. For development of molding/processing techniques, basic researches have been conducted for hot pressing/rolling, extrusion/withdrawal, powder molding and melt molding, using various reinforcing fibers. Bright prospects have been also obtained for combinations of adequate molding processes for individual materials. For development of design techniques, the basic data regarding mechanical characteristics of FRMs, both domestic and foreign, are collected, and analyzed by the trace tests with specimens, to set up the targets for FRM function improvements, viewed from the designs. (NEDO)

Report on evaluation of research and development of methods for producing basic chemicals from carbon monoxide and other stocks; Issanka tanso nado wo genryo to suru kiso kagakuhin no seizoho no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-08-01

This project was aimed at developing methods for producing basic chemicals from carbon monoxide and other stocks (the so-called C1 chemistry), in order to establish the techniques that could promote stable supply of basic chemicals from the new carbon resources in place of oil. It was a 7-year national project beginning in FY 1980, jointly implemented by the government, academic and industrial circles. Described herein are the overall evaluation of the results. There are several carbon resources other than oil, e.g., coal, natural gas, oil shale and tar sand. They are abundantly occurring, although unevenly, and various countries are developing these resources. They can be advantageously utilized as stocks for chemicals, after being converted into synthesis gases. In Japan, they have been efficiently developed cooperatively by national institutes, enterprises, academic circles and chemical industry, to produce the world's results, e.g., gas separation/purification techniques and new catalysts for new synthesis methods. This project was terminated because of the relaxed oil supply/demand situations and lowered crude prices in the middle of the 80's, which made stock conversion less urgent. (NEDO)

Fiscal 2000 report of investigation. Project for promoting international cooperation for global environment/Project for assessment on effect of climate change; 2000 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / kiko hendo eikyo hyoka nado jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Assessment and examination were conducted on the scientific/technological aspect, environmental aspect and economic/social aspect concerning measures for mitigating climate change, as a part of international cooperation in global warming issues. In the development of assessment methods for cost analysis, it revealed that, in the activities for mitigating emission of greenhouse effect gases (GHG) or for increasing carbon sequestration, benefits of the mitigation sometimes surpassed their cost, allowing the society to benefit from the mitigation. In the examination of problems in technology transfer and their solutions, it was found that, in order to attain successful transfer, partnership among the parties interested was essential and that each government was capable of promoting such partnership. In the assessment of various policy options, the situation in the U.S. is such that the market aspect of GHG emission permit and credit trading is rather weak because of immaturity in a legal framework on GHG emission trading and because of undefinedness in the systems of the Kyoto Protocol and in the possibility of its validation. However, the reason enterprises are actively participating in the early market is that they plan a risk-hedge for example in anticipation of tighter regulations in the future. (NEDO)

FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

Non-contact evaluation of mechanical properties of electroplated wear resistant Ni-P layer from the velocity dispersion of laser SAW; Laser reiki Rayleigh ha no sokudo bunsan wo mochiita taimamo Ni-P mekkiso tokusei no hisesshoku hyoka

Energy Technology Data Exchange (ETDEWEB)

Morikawa, Y.; Cho, H.; Takemoto, M. [Aoyama Gakuin University, Tokyo (Japan). Faculty of Science and Engineering; Nakayama, T. [Kobe Steel Ltd., Kobe (Japan)

1996-11-01

We developed a new laser surface acoustic wave (SAW) system and applied this to estimate the mechanical properties of the wear-resistant Ni-P layer electroplated on a stainless steel. The velocity dispersions of Rayleigh wave of the as -plated and heat-treated Ni-P layer were obtained by the one point time domain signal processing. The Ni-P layers with excellent wear resistance produced by the heated treatment higher than 725K were found to show higher Rayleigh velocities than that of the substrate steel, while the Ni-P layer with poor wear resistance showed lower velocities. Young`s moduli of the Ni-P layer, estimated so as the computed velocity dispersion agreed with the measured one, increased with the increase of wear resistance. 10 refs., 9 figs., 2 tabs.

Research and development of basic technologies for the next generation industries, 'bio-elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihtsu 'bio soshi'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed in order to establish basic technologies to realize new information processing incorporating high-order functions of living organisms, and bio-elements equipped with high-order functions. In the field of developing technical means to measure directly the information processing function of living organisms, detailed analysis has become possible for the first time on spatial operation of nerve activities by using two-dimensional beam measurement operation on the nerve activities. In the field of aiming at modeling, a system to realize functions effective in terms of engineering was structured by incorporating into the model the functions specific to nervous systems of visual sense and motion. In the field of element technologies, a large progress was seen in the basic technology and evaluation technology such as design and fabrication of molecules added with different functions in the LB membrane. Membranes having simple but different functions such as light beam and scent detection were manufactured, whereas a possibility of having them manifest functions as elements was verified. Furthermore, possibilities were discovered in manufacturing functional membranes by using self-organizing capability as a result of using basic properties possessed by polymers, and in realizing functions simulating plasticity of nerves. These achievements would lead to a belief that the targets of the first term research and development have been achieved nearly completely. (NEDO)

International research cooperation project. Assessment report on the R and D of the comprehensive development/utilization technology of energy of gas hydrate resource; Gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to 'the R and D of the comprehensive development/utilization technology of gas hydrate resource,' assessment was conducted and reported from an aspect of the third party. This R and D is a timely project being aimed at establishing the basic technology on gas hydrate from both aspects of fundamental research and practical research. In the development of gas hydrate resource in the tundra zone, the development of measuring methods for thermal conductivity and dielectric constants advanced the establishment of a guide for exploration and possibilities of assessment of the resource amount. In the development/production, it can be said that the knowledge/information collected by exchanging methane in gas hydrate with CO2 means no needs for new supply of heat and also contributes to the isolation of CO2. As to the utilization technology, the results were rated very high also internationally of tackling the quantitative evaluation method at molecular levels of the gas included in hydrate using Raman spectroscopy to establish the industrial gas separation method using the low-temperature environment in the tundra zone. (NEDO)

General evaluation survey report on fiscal 1998 investigation of geothermal development and promotion. No.C-3 Akinomiya area (Third); 1998 nendo chinetsu kaihatsu sokushin chosa sogo hyoka chosa hokokusho. No.C-3. Akinomiya chiiki (dai 3 ji)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-01

With Akinomiya area (11.4 km{sup 2}) selected in Akita prefecture as the survey C area in fiscal 1996, the first survey was conducted. This paper is a summary of memorandum from an advisory standpoint on the evaluation survey concerning the fiscal 1998 investigation results. The contents of the survey are geological investigation, precision gravity exploration, soil gas investigation, electromagnetic exploration, fluid chemical investigation, well drilling and short-term eruption test. An alteration zone was recognized around the place where clay minerals used to be mined, with the center of the zone situated 500-600 m east of a fault. The alteration condition of Akinomiya area seems to be different from that of Doroyu Wasabisawa area. The supplementary gravity survey was carried out at total 58 points in fiscal 1998. It is desirable to set supplementary measuring points over a wide surrounding area for a depth structure analysis. Also performed was a study of mercury concentration in the soil gas. While CSAMT and TDEM methods were employed for the electromagnetic exploration, a suitable method should be carefully selected for a wide area high-density exploration. Consistency with adjacent areas is essential in preparing investigation items particularly for a geothermal model. (NEDO)

FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

WE-NET substask 3. Conceptual design of the total system (City-level energy estimation and assessment); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 3. Zentai system gainen sekkei (toshi kibo deno yosoku hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The effort of fiscal 1997 at isolating the best way to introduce a relatively small amount of hydrogen into urban fuel economy was carried over to fiscal 1998. In the research of fiscal 1998, comparison was made between Tokyo and London in connection with hydrogen introduction, and a transition scenario was proposed for introducing hydrogen into Tokyo. Models were built for Tokyo and London, and studied. The result of this study was different from that obtained in the previous study, and places the two cities under similar conditions. The difference is attributed to the rapid progress in the development of the fuel cell and to the resultant reduction in cost. It is inferred that, in consideration of the transportation situation, the introduction of pure hydrogen will be the most cost-effective for both cities at least for some time to come. According to the revised data, natural gas may be procured in Tokyo as in London but the size of supply available in Tokyo is fairly smaller than that in London. Several transition scenarios covering the period up to 2025 were subjected to discussion. (NEDO)

Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

Report on final evaluation of industrial science and technology research and development system. Comprehensive basic technologies for development of ocean resources. Manganese nodule exploitation system; Kaiyo shigen sogo kiban gijutsu (mangan dankai saiko system). Saishu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

Described herein are the final evaluation results of the basic research and development of the system for exploiting manganese nodules as one of ocean resources. A 9-year project was started in the FY 1981 to establish the techniques to efficiently, economically exploit Mn nodules on a commercial basis, which are occurring on deep sea bottoms (4,000 to 6,000 m deep), in order to stably supply non-ferrous metallic resources, e.g., Ni, Cu, Co and Mn, which are essential for economic activities of Japan. Originally, the UN convention related to ocean laws raised development of unique exploitation techniques as the prerequisite condition for obtaining the right to develop Mn nodules. However, the situations around development of Mn nodules were changed since then, to devalue objects, significance and urgency of this project. The fourth amendment of the basic plans decided to suspend the comprehensive ocean tests in 1996, and to implement only the ocean/land tests in which part of the individual elementary techniques were combined. Therefore, the technological validation of the overall system could not be done sufficiently, and degree of achievement of the project is low, viewed from insufficient prospects of the commercial production. However, this project produced good results in individual elementary techniques, which are of significance for the resources policies. (NEDO)

Detection of shear-wave traveltime delay by using wavelet transform and characterization of an artificial subsurface fracture; Wavelet henkan ni yoru toka S ha denpa jikan henka no koseido kenshutsu to jinko chika kiretsu no seijo hyoka

Energy Technology Data Exchange (ETDEWEB)

Tanaka, K; Moriya, H; Asanuma, H; Niitsuma, H [Tohoku University, Sendai (Japan)

1997-05-27

As characterization of artificial cracks formed underground by using the water pressure fracturing method, experiments have been carried out to detect relationship of pressurization and S-wave propagation time with the polarizing direction dependence. Openings are created when pressure in the vicinity of the artificial cracks increases greater than reopening pressure of micro cracks. Elastic wave velocity decreases in this region because of water in the opened micro cracks. Anisotropy is created in the S-wave propagation velocity due to influence from anisotropic reopening region when the artificial cracks are pressurized, and is separated into two components which polarize orthogonally with each other (micro splitting). Field experiments conducted at the Higashi-hachimantai field were analyzed by using wavelet transform. It was possible to detect the S-wave arrival time at high accuracy, and the arrival of an orthogonally polarized wave was observed in 0.03 to 0.11 ms after the arrival of the S-wave. Possibility was indicated on separation of the two components in the orthogonally polarized wave of the S-wave if the micro splitting is used. If this mechanism is elucidated, it may be possible to extract information on cracking systems (direction of micro crack orientation and crack density). 8 refs., 10 figs.

Report on evaluation of research and development of methods for producing basic chemicals from carbon monoxide and other stocks; Issanka tanso nado wo genryo to suru kiso kagakuhin no seizoho no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-08-01

This project was aimed at developing methods for producing basic chemicals from carbon monoxide and other stocks (the so-called C1 chemistry), in order to establish the techniques that could promote stable supply of basic chemicals from the new carbon resources in place of oil. It was a 7-year national project beginning in FY 1980, jointly implemented by the government, academic and industrial circles. Described herein are the overall evaluation of the results. There are several carbon resources other than oil, e.g., coal, natural gas, oil shale and tar sand. They are abundantly occurring, although unevenly, and various countries are developing these resources. They can be advantageously utilized as stocks for chemicals, after being converted into synthesis gases. In Japan, they have been efficiently developed cooperatively by national institutes, enterprises, academic circles and chemical industry, to produce the world's results, e.g., gas separation/purification techniques and new catalysts for new synthesis methods. This project was terminated because of the relaxed oil supply/demand situations and lowered crude prices in the middle of the 80's, which made stock conversion less urgent. (NEDO)

Research and development of the industrial basic technologies of the next generation, 'composite materials (resin-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (jushikei)'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-30

The results of the first phase research and development project for developing the resin-based composite materials as the basic technologies of the next generation are evaluated. This project is aimed at development of the resin-based composite materials as light, high-strength and high-rigidity structural materials. Development of the basic techniques for these materials is of high significance, and highly rated. The first R and D phase efforts are directed to synthesis of new skeleton and terminal compounds, and their introduction into the matrices; application/combination of various fiber surface modification techniques; development of the basic techniques for intermediate materials for three-dimensional fabrics, triaxial fabrics and hybrid materials; improvement of the main techniques for a series of molding/processing steps; adoption of new methods; and development of design programs and elementary design techniques. The technical targets of improving functions of each item have been achieved, or bright prospects have been obtained therefor, each involving potentials of functional improvements by developing new functions. It is also considered that the parallel, competitive development and promotion of 7 routes in researches on the matrix resins have brought great effects. (NEDO)

Fiscal 1996 survey report. Data collection and evaluation analysis in the project on field tests on the fuel cell generation; 1996 nendo kenkyu hokokusho. Nenryo denchi hatsuden field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper installed fuel cell power generation equipment experimentally at various facilities which are the final diffusion form of the new energy power generation, conducted long-term operation under the actual load, collected/analyzed various data, arranged them as data useful for full scale introduction/diffusion, aiming at forming the base for general diffusion of the fuel cell power generation. The number of the systems installed for field test execution has been 24 places/28 units since the start of the project, and the system capacity totaled 4,250kW. The actual operation hours in five years are 6,000-28,000. In fiscal 1996, the average cumulative accumulated operational rate was approximately 68%, a little over that in fiscal 1995, 65%. The average load factor was 69% in fiscal 1995 and 70% in fiscal 1996. The utilization rate increased as a whole to about 57% on average if seeing only fiscal 1996, as compared with that in fiscal 1995, about 48%. The power generating efficiency was approximately 34% on average. As to the status of shutdown of the fuel cell power generation, the paper surveyed the average interval of failure, the rate of frequency of shutdown, the analysis of shutdown, etc. 250 figs., 29 tabs.

Achievement report on contract research. Large-scale project - Results of 1st-phase research and development of MHD power generation system; Plant system no hyoka. Ogata project dai 1 ki MHD hatsuden system kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

Described in detail involving the results of component development, assessment, and the indication of problems are the power generation channel, superconductive magnets and a helium refrigeration and liquefaction unit, seeds collector, heat exchanger, combustor, etc. Described involving the result and effect of power generation system research and development and the indication of problems is the research on Mark V and Mark VI operation tests. Described in relation to thermal performance calculation, economic effectiveness calculation, and environmental conservation involving an MHD (magnetohydrodynamic) power plant are the combustion of heavy oil, combustion of natural gas, plant having a 1,000MW power generator as its base load, control of NOx and sulfur in MHD power generation, etc. As for planning for the next stage, the configuration of a 10MW MHD power generation plant, its equipment, construction cost, and preliminary element research, etc., are described. Furthermore, propositions are presented concerning future plans and the prospect of commercial MHD power generators, technological ripple effects due to MHD power generation research and development, and research and development in the future. (NEDO)

Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the second phase research and development; Jisedai sdangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzoukei)'. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-31

The results of the second phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to modification of PAN-based high-strength carbon fibers for aluminum-based FRMs, and also to development of the methods for controlling interfacial reactions at high temperature by modification of the base materials for titanium-based FRMs. For development of carbon fiber-based intermediate materials, the techniques are developed for continuous production of wire preforms of aluminum. For development of molding/processing techniques, the press molding and powder HIP molding techniques are developed to give a planar product of the FRM of titanium alloy reinforced with evaporated filaments of silicon carbide, which shows an average tensile strength exceeding the target level. Also developed are the press and roll molding techniques for the wire preforms of aluminum reinforced with silicon carbide fibers, the planar product therefrom showing a tensile strength of at least 99% of the base material. It is concluded that the objectives of the second-phase project are almost achieved. (NEDO)

Study of the ablation of extra-low temperature aggregate target and the development of technology of formation of non-equilibrium high-quality functional thin films by the plume control; Gokuteion gyoshutai target no abureshon oyobi purumu seigyo ni yoru hiheiko kohinshitsu kinosei usumaku seisei gijutsu kaihatsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A study was made on factors of the formation of high-quality thin films in the pulse laser deposition (PLD) method, a synthesis method of high-grade functional material thin films. In the experiment, plume current measurements using Cu target were conducted for the control of electric and magnetic fields. Especially, the measuring evaluation was made of the two-dimensional distribution including not only the central part of the substrate placed opposite to the target, but the periphery of the substrate. As a result, the following was found out. The distribution of charged particles in the plume is different in positive charge and negative charge, and the negative charge is dispersed/distributed more widely. Accelerating/decelerating effects of charged particles by the electric field are saturated when the bias voltage absolute value is approximately 100V. Ionization is promoted by giving the magnetic field, and the plume distribution is expanded. Positive charged particles of the plume in the magnetic field are decelerated. In the distribution control by giving the electric field, it is effective to think improvement of the distribution not by attracting charged particles by the electric field, but by shutting out charged particles of the same polarity. 29 refs., 75 figs., 2 tabs.

Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of amorphous solar cells (Research on amorphous silicon-based new materials); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Amorphous silicon kei shinzairyo no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In an a-Si{sub 1-x}Ge{sub x}:H film formed by decomposition in a glow discharge, since Ge-H is weaker than Si-H in terms of bonding, an increase in the amount of Ge decreases the amount of H and increases the number of Ge dangling bonds (DBs). Actually, however, H bonded to Si also decreases the number of DBs in Ge. This suggests that H is not working only to terminate DBs but that it also decreases the number of DBs through its structure-softening effect. In the case of a-Si{sub 1-x}C{sub x}:H, an increase in C results in an increase in H and in the number of DBs in both Si and C, this because C-H is stronger than Si-H in terms of bonding. F in a film is quite mobile. SiF and SiH in presence as distributed are found to decrease the number of DBs. Concerning the effect of hydrogen plasma processing for a-Si formed by thermolysis (CVD: chemical vapor deposition), the light transmission rate, absorption, ESR (electro-spin resonance) process time, and dependency on film thickness are investigated, and the relationship is examined between the defect-reducing effect of the H taken into the film and the transmission of light. It is found, as the result of experiments by a simplified molecular orbital method, that DBs stay in existence keeping away from where H or F is in presence. (NEDO)

Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

Feasibility study of international cooperation in the research/development of a solar energy utilization system by the innovative solar thermochemical process; Kakushinteki solar netsukagaku process ni yoru taiyo energy riyo system no kaihatsu kenkyu ni kakawaru kokusai kyoryoku kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

At COP3 in 1997, an agreement was made to the innovative technical development/promotion by international cooperation, and the promotion of transfer of environmental technology to developing countries. Under the agreement, a feasibility study of international cooperation was made, and especially a study was conducted of the utilization/development of solar energy by the innovative solar thermochemical process. The main reason for global warming is emissions of a large amount of CO2 caused by the direct combustion of fossil fuels. Therefore, a CO2 recycle system taken up in the study enables a more substantial decline in CO2 emission (kg/kWh) per unit generation than the conventional thermal power system by composing solar methanol or solar dimethyl ether using fossil fuels including coal, water, CO2, etc. as raw materials and using solar energy as heat source, and by using this as fuel (solar fuel). CO2 can be reduced by 13% to 14% by substituting solar methanol or solar dimethyl ether produced from petroleum/methane equivalent-mol mixed raw materials for the equivalent mol coal and natural gas of the thermal power plant (CO2 recovery is not necessary). 34 refs., 47 figs., 34 tabs.

Achievement report for fiscal 1984 on Sunshine Program-entrusted research and development. Research and development of amorphous solar cells (Research on amorphous silicon interface); 1984 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Amorphous silicon no kaimen no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

As for the formation of amorphous semiconductors by photo-CVD (chemical vapor deposition) processes, details are examined of a-Si formed by the excimer laser-excited photo-CVD process, a-SiC formed by the directly excited photo-CVD process, a-SiGe formed by the mercury sensitized reaction photo-CVD process, and {mu}c-Si formed by the mercury-sensitized reaction photo-CVD process. It is then found that all of the said materials are superior to a product of the plasma CVD process in terms of film quality. As for the fabrication of amorphous Si solar cells by a photo-CVD process, a 3-separate-chamber unit is built, in which all the p-, I-, and n-layer are formed by photo-CVD. It is then found that the introduction of a buffer layer into the p/I interface is a powerful tool to enhance efficiency and that the use of the buffer zone brings about an increase of 9% or more in conversion efficiency. In the case of an amorphous solar cell using monosilane, buffer layer introduction results in a conversion efficiency of 9.05%. (NEDO)

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of elementary technologies for low-cost polycrystalline cell modules; Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Takessho cell module tei cost ka yoso gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of elementary technologies for low-cost polycrystalline cell modules in fiscal 1994. (1) On development of elementary technologies for mass production, fast surface machining, fast electrode forming and fast forming of junctions and antireflection films were studied. Surface machining by rotating grindstone was studied as fast cutting of fine grooves on Si substrates, resulting in possible fast machining superior in shape accuracy. Electrode properties equivalent or superior to previous ones were obtained by fast electrode forming using a fast printing/sintering equipment even at transfer speed 7.5 times as high as that of conventional methods. Simultaneous fast forming of junctions and antireflection films were achieved by heat treatment after deposition on Si substrate surfaces while heat-decomposing Ti and P compound gas. (2) On development of module structure, an optimum cell group angle, low reflection rate at glass surface, and fast wiring were studied. 5 figs., 2 tabs.

Method for estimation of the output electric power of PV module with considering environmental factors. Method for estimation of output using I-V curves; Kankyo inshi wo koryoshita taiyo denchi module no shutsuryoku keisanho. I-V tokusei curve ni yoru keisan

Energy Technology Data Exchange (ETDEWEB)

Yamagami, Y; Tani, T [Science University of Tokyo, Tokyo (Japan)

1996-10-27

Based on the basic quality equation of photovoltaic (PV) cell, a quality equation of PV module has been constructed by considering the spectral distribution of solar radiation and its intensity. A calculation method has been also proposed for determining the output from current-voltage (I-V) curves. Effectiveness of this method was examined by comparing calculated results and observed results. Amorphous Si (a-Si) and polycrystal Si PV modules were examined. By considering the environmental factors, differences of the annual output between the calculated and observed values were reduced from 2.50% to 0.95% for the a-Si PV module, and from 2.52% to 1.24% for the polycrystal Si PV module, which resulted in the reduction more than 50%. For the a-Si PV module, the environmental factor most greatly affecting the annual output was the spectral distribution of solar radiation, which was 3.86 times as large as the cell temperature, and 1.04 times as large as the intensity of solar radiation. For the polycrystal PV module, the environmental factor most greatly affecting the annual output was the cell temperature, which was 7.05 times as large as the spectral distribution of solar radiation, and 1.74 times as large as the intensity of solar radiation. 6 refs., 4 figs., 1 tab.

Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

Assessment of effects of maturity of Japan`s economy and society and improvement in automotive fuel consumption on demand for automotive fuels; Nippon keizai shakai no seijukuka to nenpi kaizen ga jidoshayo nenryo juyo ni ataeru eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Shimomura, S. [The Institute of Energy Economics, Tokyo (Japan)

1998-04-01

This paper evaluates impacts of the maturity of Japan`s economy and society and the improvement in automotive fuel efficiency on the demand for automotive fuels by FY 2010. Standard case and lower order case were examined. When the traffic volume of passenger cars in FY 1995 is assumed to be 100, it become 121 and 119 in standard and lower order cases, respectively. The traffic volume of lorries become 106 and 102 in standard and lower order cases, respectively, which showed a rather small growth. Deterioration rate of the fuel consumption was estimated by considering the difference in fuel consumption of new cars and existing cars. Although the fuel consumption will be lowered by FY 2000 when the cassation rate of ordinary passenger cars will rapidly increase, the impact will be lowered after that. For lorries for commercial use, the running fuel consumption will be gradually lowered due to the increased carrying capacity and vehicle weight a lorry with improving the transportation efficiency. Decreased running speed by traffic jam is also a cause of the deterioration of fuel consumption. When a policy of improvement in the fuel consumption is promoted in a background of CO2 issues, the fuel consumption of each vehicle will be gradually improved. The peak of fuel demand will be in FY 2005 by considering the changes in economical and social structures and the improvement in fuel consumption for the environmental protection. 5 figs., 3 tabs.

Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly efficient polymeric separation membrane material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo saishu kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-01

For the enhancement of separation process efficiency and energy efficiency in the chemical industry, etc., basic technologies are developed involving high-performance separation membrane materials which are excellent in durability and usable in the field where separation by membranes has been impractical. The liquid mixtures subjected to separation are a neutral organic compound/water system, an acidic organic compound/water system, and a polar organic compound/water system; the gas mixtures subjected to separation are an oxygen/nitrogen system and a carbon monoxide/nitrogen system. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. Among those that have to be mentioned is the development of a nonaqueous separation membrane, a supported liquid membrane with amino acid optically active high performance separation capability, a high-precision evaluation unit for gas separation membrane characteristics, a selective permeation membrane with high-level oxygen and carbon monoxide carriers and reactivation technology, a high-performance ethanol separation membrane, a water/polar organic compound separation membrane, and a water/acetic acid separation membrane and stability providing technology. In particular, the water selective permeation membrane for a mixture of water and alcohol has already arrived at the stage of bench plant demonstration. (NEDO)

FY 1980 Report on results of research and development project, commissioned by Sunshine Project. Analysis and evaluation of coal liquefied oil, and development of its applications; 1980 nendo sekitan ekikayu no bunseki hyoka to yoto kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the first year of the 5-year survey/research project for analysis/evaluation of coal-liquefied oil, structural analysis and development of its applications. The program for analysis/evaluation of coal-liquefied oil includes surveys on the analytical methods for liquefied coal, which are compared with those for oil products, elementary analysis of the ashes in SRC, binder performance tests, and extraction of the problems to be solved for proposal of the analytical methods for coal-liquefied oil. The program for structural analysis includes that of coal-liquefied oil fractionated into middle distillate, fuel oil asphalt and pitches, configurations of a large-size liquefaction process, and characteristics of the oil produced thereby, and some examples of structural analysis are reported. The molecular species and compositions are determined for the middle distillate fraction.. The fuel oil shows average structures of diversified mixtures. The program for developing applications of coal-liquefied oil includes extraction of the problems anticipated when it is used as fuel, technical/economic evaluation of the upgrading techniques, and results and evaluation of conversion of the oil into stocks for chemicals. (NEDO)

Survey report for fiscal 1999. Evaluation and analysis on items applied for in high-performance industrial furnace introduction field test project in fiscal 1999; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Obo anken hyoka bunseki

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes comprehensive evaluation and analysis mainly on the 51 items adopted in the high-performance industrial furnace introduction field tests. The development of a high-performance industrial furnace has completed the fundamental development research in fiscal 1998, and the possibility was verified on energy saving of more than 30% and reduction of NOx emission by 50% over that by conventional furnaces. Upon this fundamental achievement, the field test project has started as the comprehensive approach to developing the practically usable technologies for three years from fiscal 1998 until fiscal 2000, which is being promoted as a joint research project. According to the survey on the actual state in fiscal 1998, a little less than 20,000 industrial furnaces having combustion capacity of more than 500,000 Kcal/hr (excepting boilers) are being used. If these furnaces are converted into the high-performance industrial furnace, energy conservation of 210,000 x 10{sup 6} Mcal (converted to crude oil of 22.7 x 10{sup 6} kl/year) can be achieved from the maximum annual energy consumption of 700,000 x 10{sup 6} Mcal (converted to crude oil of 75.7 x 10{sup 6} kl/year). This conservation amount corresponds to about 12% of the final energy consumption in the whole Japanese industrial departments in fiscal 1996. It is expected that the performance of the full-size high-performance industrial furnace will be verified, and this technology will be promoted for wide proliferation. (NEDO)

Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

FY 1998 report on the results of R and D projects by local consortiums for immediate effects. Development of titanium dioxide thin film photocatalysts sensitive to visible light and their applications to cleaning systems; 1998 nendo kashiko kasseina sanka chintan hikari shokubai usumaku no kaihatsu to sono system oyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D project has been implemented for developing the thin film-making process techniques which can increase areas of titanium oxide (TiO{sub 2}) photocatalysts sensitive to visible light and their mass production. The fundamental investigations are directed to elucidation of the mechanisms involved in manifestation of activity in visible light of the visible light-sensitive thin film doped with the Cr, V or other ions. The sputtering involving no ion implantation is devised for producing the thin films, to realize the highest visible light sensitivity recorded for the thin TiO{sub 2} film. The sputtering process is investigated in detail for the film-making conditions, e.g., Ar pressure, effects of coexisting O{sub 2} gas, and power gap. The conditions under which the thin film serviceable under commercial conditions can be produced are not established yet, but it is confirmed that the coating film shows superhydrophilicity and photocatalytic activity for, e.g., sterilization, when irradiated with ultraviolet ray. The method has been established for evaluating deodorizing and contamination-preventive functions of the thin films in ultraviolet and visible rays. The project has also confirmed applicability of the techniques to the commercial products, and established the self-cleanable catalyst by combining the oxide catalytic function with the photocatalytic function. (NEDO)

Report on the FY 1999 R and D on high temperature superconducting flywheel energy storage. System design/evaluation (Comparative study and information collection); 1999 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu. System sekkei hyoka (hikaku kento, joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Following the previous fiscal year, a flywheel technology survey committee by men of learning and experience was organized to make a comparative study on various flywheel energy storage systems. Concerning the list-making for checking each element of the high temperature superconducting flywheel system, characteristics and reasons for employment of the small model and medium model were outlined in terms of the system structure (structure in single unit, structure in more than one units), flywheel, bearing, electrically-driven generator, etc. Also about the system in which no superconducting magnetic bearing is used, the information is collected in Japan and abroad through internet, etc., to outline the system. Further, main results obtained in the project were made public in main international conferences or academic meetings such as EUCAS and ISOTC108. At the same time, visits were paid to research institutes such as Cambridge University in the U.K. for the purpose of supplementing the survey so far made, to investigate the recent trend of the research. (NEDO)

Fiscal 1997 research report on the data collection, evaluation and analysis in the PV power generation field test project for public facilities; 1997 nendo kokyo shisetsu nado yo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As a part of the field test project for diffusing PV power generation into public facilities generally, evaluation and analysis were made on the collected data from 105 sites installed during fiscal 1993-1996. Analysis of operation characteristics was made by using parameters obtained by developing a basic equation for every component. 94% of all the sites fell under the total solar irradiation of 3.0- 4.5kWh/m{sup 2}/D. 83% of those fell under the equivalent array operation time of 2.5-4.0h/D. 70% of those fell under the equivalent system operation time of 2.5-3.5h/D. 72% of those fell under the system operation time of 9.0-12.0h/D. 78% of those fell under the effective inverter efficiency of 0.84- 0.96. 68% of those fell under the inverter load factor of 0.25-0.35. 85% of those fell under the array performance ratio of 0.7-1.0. 83% of those fell under the system performance ratio of 0.6-0.9. The generation cost decreased from 270yen/kWh in 1993 to 100yen/kWh in 1996 because reduction of an installation cost largely contributed to reduction of the total cost. (NEDO)

Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-30

The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of evaluation method for gene inspection system; 2000 nendo shinki sangyo shiengata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensa system no hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Discussions and deliberations were given by the comprehensive survey committee on standardization of a total gene inspection system from specimen adjustment necessary for the gene inspection system to data processing. This paper summarizes the achievements in fiscal 2000. In standardization related to the specimen procedure and the inspection technique, the specimen storing method and the report statement contents were established. In addition, verification was made on the heat-resistant enzyme reagent and such measuring devices as the electric migration device and the photographing device. Discussions were given on standard substances used in the gene inspection. Regarding the K562 cell strain, cross-checking was performed in three institutions, wherein discussions were given on interchangeability of the inspection results, and the usefulness of the K562 cell as a standard substance. As a result, all the three institutions have come to an agreement on the Southern method, the FISH method and the RT-PCR method, but not on the real-time PT-PCR method, leaving the subject as the future assignment. In the survey for Europe and America, visits were made to AFNOR, CEN, DIN, FDA and CAP for the attempt of collecting information and establishing international exchange. (NEDO)

Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-30

The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

Report on results 1998. Research and development on high-temperature superconducting flywheel power storage (system design/evaluation (comparative assessment/information collection)); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (system sekkei, hyoka (hikaku kento, joho shushu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

For the purpose of evaluating the basic characteristics of high-temperature superconducting magnetic bearings (SBM), a system model is designed, experimentally manufactured and tested, which is embodied in the design/evaluation of a large-scale system, with an investigation carried out for the introduction of the system into an electrical power system. In this framework, an examination and research were conducted for the system design technology on which each component technology in the system structure can be applied consistently in the system. In the comparative assessment of various flywheel power storage systems, the specifications and achievements were compared in the component elements of the flywheel systems developed in Europe, America and Japan through the literature studies and the field survey, with examination performed towards the future development. As a result, it was found that, in America, bearings were all SMB's without control. Boeing's objective for the development is 10kWh or so in view of convenience for transportation and is prone to arrange it in numbers. Further, investigations were made in literature and documents on the domestic and international trend of development of high-temperature superconducting flywheel systems, elucidating the details of the development. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Standardization of the fine bioceramics testing/evaluation methods; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seitaiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research and development of the fatigue characteristics of the bioceramics, fatigue and impact-resistance characteristics of the members of these materials, and methods of evaluating their compatibility with a living body, for proposing the international standards. The test results of alumina and zirconia as the bioceramics indicate that their bending fatigue characteristics greatly depend on environmental conditions and frequency, suggesting necessity for the evaluation in the environments which simulate the living body inside. The compression and impact tests are conducted for the artificial femoral heads with a taper. It is found that the simulated body fluid, having the dissociated ion concentration adjusted at the level in the human blood plasma, remains unchanged in the concentration at 36.5 degrees C for 4 weeks; the ion concentration is unaffected by filtration with the aid of the microfilter useful for, e.g., removal of bacteria; and the synthetic apatite has almost the same composition as that for the bones in a living body. It is also suggested that activity of the bioactive ceramics can be evaluated by their ability for forming apatite in the simulated body fluid. (NEDO)

Report on results 1998. Research and development on high-temperature superconducting flywheel power storage (system design/evaluation (comparative assessment/information collection)); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (system sekkei, hyoka (hikaku kento, joho shushu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

For the purpose of evaluating the basic characteristics of high-temperature superconducting magnetic bearings (SBM), a system model is designed, experimentally manufactured and tested, which is embodied in the design/evaluation of a large-scale system, with an investigation carried out for the introduction of the system into an electrical power system. In this framework, an examination and research were conducted for the system design technology on which each component technology in the system structure can be applied consistently in the system. In the comparative assessment of various flywheel power storage systems, the specifications and achievements were compared in the component elements of the flywheel systems developed in Europe, America and Japan through the literature studies and the field survey, with examination performed towards the future development. As a result, it was found that, in America, bearings were all SMB's without control. Boeing's objective for the development is 10kWh or so in view of convenience for transportation and is prone to arrange it in numbers. Further, investigations were made in literature and documents on the domestic and international trend of development of high-temperature superconducting flywheel systems, elucidating the details of the development. (NEDO)

Survey report for fiscal 1998. Evaluation by industrial circles of the COP3 outcome and their future response (America); 1998 nendo chosa hokokusho. COP3 no kekka ni taisuru sangyokai no hyoka oyobi kongo no taio ni tsuite (Beikoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Response in America to COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) is investigated. Office of Energy Efficiency and Renewable Energy (EE) of America's Department of Energy conducts activities designed to protect environments and supports America's economic competitiveness. The scope of EE activities is quite wide, covering efforts at energy efficiency improvement and renewal energy utilization for all energy consuming sectors involving construction work and equipment for buildings, various industries and public utility works, and transportation. EE also supports and promotes the development of advanced industrial materials, electric vehicles, hybrid vehicles, fuel cells, etc. In the field of renewable energy, it deals with the exploitation of sunlight, biomass, wind force, water power, geothermal energy, etc. It also supports efficiency improvement efforts being undertaken through studies of advanced power transmission and distribution, high-temperature superconduction, energy storage, etc. The said supports are provided not only by Federal Government but also by state governments, and include financial aids. A number of programs are under way, worked out and promoted by the respective bureaus and departments. They are evaluated, protected, and implemented through the partnership of official and civilian organizations. (NEDO)

Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

Achievement Report for fiscal 1997 on developing a silicon manufacturing process with reduced energy consumption. Development of silicon mass-production manufacturing technology for solar cells; 1997 nendo energy shiyo gorika silicon seizo process kaihatsu. Taiyo denchiyo silicon ryosanka seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to manufacture silicon for solar cells, development is intended on a technology to manufacture silicon (SOG-Si) for solar cells by means of metallurgical methods using metallic silicon with purity generally available as an interim starting material. The silicon is required of p-type electric conductivity characteristics with specific resistance of 0.5 to 1.5 ohm per cm, to be sufficient even with 6-7N as compared to silicon for semiconductors (11-N), and to be low in cost. While the NEDO fluid bed process and the metallurgical NEDO direct reduction process have been developed based on the technology to manufacture silicon for semiconductors, the basic policy was established to develop a new manufacturing method using commercially available high-purity metallic silicon as an interim starting material, with an objective to achieve cost as low as capable of responding to small-quantity phase production for proliferation purpose. Removal of boron and phosphor has been the main issue in the development, whereas SOG-Si was manufactured in a laboratory scale by combining with the conventional component technologies in fiscal 1991 and 1992. The scale was expanded to 20 kg since fiscal 1993, and a five year plan starting fiscal 1996 was decided to develop the technology for industrial scale. Fiscal 1997 has promoted the development by using the 20-kg scale device, and introduced facilities to develop technology for mass-production scale. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on metal system materials); 1974 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Kinzokukei zairyo no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-30

This report describes the fiscal 1974 research result on metal system materials for solar cooling/heating and hot water supply systems. Study was made on cathodic protection of a roll bond heat collection board promising as Al plane collector. The protection is dependent on sacrificial anode materials. Al-Zn system alloy including minute amounts of In and Sn was effective in protection by transferring natural electrode potential to a base side largely, however, excess addition of In and Sn increased self-corrosion, remaining some issues to be solved. The prototype water flow corrosion test equipment was prepared for corrosion analysis of an Al roll bond collector natural circulation hot water supplier. Preliminary study was made to give selective absorption power (large short-wave absorption and small long-wave radiation from collector surfaces) to a collector. Deposition of Cu, Ni, Co and Sn oxides as black semiconductors into Al anodic oxidation film porous layers by secondary electrolysis was invalid as well as a painting method. Glossy Ni plating onto Al and black Cr and Ni plating onto the surface more elevated solar exposure surface temperature by more than 20% than black painting. (NEDO)

Achievement report for fiscal 1991 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on low-temperature film formation technology); 1991 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Teion seimaku gijutsu no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

For the establishment of a low-temperature formation technology for compound semiconductor polycrystalline thin film of CuInSe{sub 2}, research is conducted involving film formation and film quality evaluation using the ICB (ion cluster beam) method. In the research on the film formation, an In-excessive film is placed on a Cu-excessive CuInSe{sub 2} film using the ICB method for the formation of a two-layer film. Bulk CuInSe{sub 2} and thin-film polycrystalline CuInSe{sub 2} are evaluated using PL (photoluminescence) spectrums excited by YAG (yttrium aluminum garnet) and Ar. In both bulk and thin film, it is suspected that clues are latent in the levels deeper than hitherto reported. A luminescent belt of 0.75eV is detected. Changes in film quality before and after oxygen annealing are verified using the YAG-excited and Ar-excited PL spectrums, and the result suggests the feasibility of tracking the process in which the effect of annealing propagates inward from the interfacial surface. Fe-added single-crystal CuInSe{sub 2} is investigated for the optical and photoelectrical effects of Fe impurities. (NEDO)

Achievement report for fiscal 1991 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on forbidden band width optimization); 1991 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Kinsei taifuku no saitekika no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

Research is conducted on film formation technologies etc. for the chalcopyritic compound semiconductors represented by CuInSe{sub 2} which is the most excellent of the materials for thin-film solar cells. As for the development of a encapsulated selenization method, research is conducted on an In formation method, temperature program for heat treatment, and Cu-In alloy film selenization, and then a CuInSe{sub 2} film less to suffer phase separation is obtained. In the development of a vaporized selenization method, the reactor tube and the temperature program are improved, and this results in a CuInSe{sub 2} film excellent in homogeneity. As for the evaluation of CuInSe{sub 2} film, photoluminescence is measured using a solid-phase selenized film, vapor-phase selenized film, and 3-source vapor-deposited film, and the result shows that photoluminescence-assisted CuInSe{sub 2} film evaluation is quite promising. In the development of ZnO film formation technologies, the MOCVD (metalorganic chemical vapor deposition) technology is almost complete, and film formation on a 10cm-square substrate is now practical. (NEDO)

Achievement report for fiscal 1992 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on forbidden band width optimization); 1992 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Kinsei taifuku no saitekika no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

Research is carried out on technologies concerning CuInSe{sub 2} thin-film solar cell manufacturing, thin film formation, thin film characterization, CdS, (CdZn)S formation, CuInSe{sub 2} single junction, analysis of the a-Si/CuInSe{sub 2} tandem solar cell operating theory, etc. In relation with the encapsulated selenization method for film formation for CuInSe{sub 2} thin-film solar cells, film constitution, film thickness, selenization temperature, etc., are studied for optimization. In relation with the vaporized selenization method, vaporized selenization is tested in a vacuum chamber aiming at improved homogeneity and reproducibility. In research on CdS and (CdZn)S which are window layer materials for CuInSe{sub 2} thin-film solar cells, CdS thin films are formed in a solution growth method using CdSO{sub 4} and (NH{sub 2}){sub 2}CS. In relation with the solution growth of the (CdZn)S crystal film, control of the Zn content in the film is now practicable. In the study of a-Si/CuInSe{sub 2} tandem solar cells, an analytical program is formulated, and calculation is made concerning the impacts of CuInSe{sub 2} forbidden band width and a-Si i-layer thickness. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on glass system materials); 1974 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Glass kei zairyo no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-26

This report describes the fiscal 1974 research result on glass system materials of plane collectors for solar cooling/heating. A barrel lens type collector was poorer in efficiency than conventional ones. A one-directional Fresnel lens type one was promising for improvement of solar radiation collection. The prototype In{sub 2}O{sub 3} selective transmission cover glass was prepared by vacuum deposition. Although selective characteristics including a solar transmissivity of 74% and an IR reflectance of 75-80% were obtained, further improvement of more than 10% is necessary. The evaluation results of some collectors are as follows. A vacuum type is poor because of its low efficiency and necessary vacuum sealing. A multi-layer type shows unsatisfactory performance at some temperatures. A glass honeycomb type is most likely because of its uppermost collection efficiency, however, development of production technology of heat-resistant honeycombs and its profitability remain to be solved. A deformed multi-layer type is practical because of its high efficiency, simple structure and low cost. Further improvement of the transmissivity and IR reflectance of cover glass by more than 10% is necessary. (NEDO)