Study of liquid hydrogen and liquid deuterium cold neutron sources

International Nuclear Information System (INIS)

Harig, H.D.

1969-01-01

In view of the plant of the cold neutron source for a high flux reactor (maximal thermal flux of about 10 15 n/cm 2 s) an experimental study of several cold sources of liquid hydrogen and liquid deuterium has been made in a low power reactor (100 kW, about 10 12 n/cm 2 s). We have investigated: -cold neutron sources of liquid hydrogen shaped as annular layers of different thickness. Normal liquid hydrogen was used as well as hydrogen with a high para-percentage. -Cold neutron sources of liquid deuterium in cylinders of 18 and 38 cm diameter. In this case the sources could be placed into different positions to the reactor core within the heavy water reflector. This report gives a general description of the experimental device and deals more detailed with the design of the cryogenic systems. Then, the measured results are communicated, interpreted and finally compared with those of a theoretical study about the same cold moderators which have been the matter of the experimental investigation. (authors) [fr

Liquid hydrogen production via hydrogen sulfide methane reformation

Energy Technology Data Exchange (ETDEWEB)

Huang, Cunping; T-Raissi, Ali [University of Central Florida, Florida Solar Energy Center, 1769 Clearlake Road, Cocoa, FL 32922 (United States)

2008-01-03

Hydrogen sulfide (H{sub 2}S) methane (CH{sub 4}) reformation (H{sub 2}SMR) (2H{sub 2}S + CH{sub 4} = CS{sub 2} + 4H{sub 2}) is a potentially viable process for the removal of H{sub 2}S from sour natural gas resources or other methane containing gases. Unlike steam methane reformation that generates carbon dioxide as a by-product, H{sub 2}SMR produces carbon disulfide (CS{sub 2}), a liquid under ambient temperature and pressure - a commodity chemical that is also a feedstock for the synthesis of sulfuric acid. Pinch point analyses for H{sub 2}SMR were conducted to determine the reaction conditions necessary for no carbon lay down to occur. Calculations showed that to prevent solid carbon formation, low inlet CH{sub 4} to H{sub 2}S ratios are needed. In this paper, we analyze H{sub 2}SMR with either a cryogenic process or a membrane separation operation for production of either liquid or gaseous hydrogen. Of the three H{sub 2}SMR hydrogen production flowsheets analyzed, direct liquid hydrogen generation has higher first and second law efficiencies of exceeding 80% and 50%, respectively. (author)

Forced convection of liquid hydrogen - part 2 - case of large temperature differences between the fluid and the wall - final report (cylindrical channel); Convection forcee de l'hydrogene liquide - 2. partie - cas de grands ecarts de temperatures entre fluide et paroi - rapport final (canal cylindrique)

Energy Technology Data Exchange (ETDEWEB)

Perroud, P; Rebiere, J [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1964-07-01

certain nombre d'experiences ont ete faites sous pression supercritique de 16 atm), vitesse massique de 11 a 115 g/cm{sup 2}.s, densite de flux de chaleur de 9 a 385 W/cm{sup 2}, temperature de paroi atteignant 800 deg. K. L'hydrogene liquide utilise etait compose de 60 pour cent de parahydrogene environ (la transformation para-ortho n'intervient pas dans les echanges). Un modele d'ecoulement, en relation avec la temperature de paroi observee, est etabli. Dans la region ou l'ecoulement se fait en double-phase, la temperature de paroi decroit fortement et passe par un minimum au moment ou le titre de yapeur reel atteint l'unite. Une correlation des coefficients locaux d'echanges thermiques est presentee, d'une part dans la region en double-phase (titre variant de 0 a 1) et, d'autre part, dans la region en phase gazeuse homogene (Reynolds variant de 15 000 a 420 000). Comparaison avec les correlations anterieures est egalement donnee. Dans la region en phase mixte, la perte de charge par frottement est negligeable devant la chute de pression due a la variation de la quantite de mouvement. Cette derniere peut se calculer avec une bonne approximation a l'aide d'un modele unidimensionnel. La perte de charge en phase gazeuse obeit aux lois classiques. On donne en annexe les proprietes physiques de l'hydrogene liquide extraites de la litterature la plus recente. (auteurs)

Fractional Consumption of Liquid Hydrogen and Liquid Oxygen During the Space Shuttle Program

Science.gov (United States)

Partridge, Jonathan K.

2011-01-01

The Space Shuttle uses the propellants, liquid hydrogen and liquid oxygen, to meet part of the propulsion requirements from ground to orbit. The Kennedy Space Center procured over 25 million kilograms of liquid hydrogen and over 250 million kilograms of liquid oxygen during the 3D-year Space Shuttle Program. Because of the cryogenic nature of the propellants, approximately 55% of the total purchased liquid hydrogen and 30% of the total purchased liquid oxygen were used in the Space Shuttle Main Engines. The balance of the propellants were vaporized during operations for various purposes. This paper dissects the total consumption of liqUid hydrogen and liqUid oxygen and determines the fraction attributable to each of the various processing and launch operations that occurred during the entire Space Shuttle Program at the Kennedy Space Center.

Microwave plasma for hydrogen production from liquids

Directory of Open Access Journals (Sweden)

Czylkowski Dariusz

2016-06-01

Full Text Available The hydrogen production by conversion of liquid compounds containing hydrogen was investigated experimentally. The waveguide-supplied metal cylinder-based microwave plasma source (MPS operated at frequency of 915 MHz at atmospheric pressure was used. The decomposition of ethanol, isopropanol and kerosene was performed employing plasma dry reforming process. The liquid was introduced into the plasma in the form of vapour. The amount of vapour ranged from 0.4 to 2.4 kg/h. Carbon dioxide with the flow rate ranged from 1200 to 2700 NL/h was used as a working gas. The absorbed microwave power was up to 6 kW. The effect of absorbed microwave power, liquid composition, liquid flow rate and working gas fl ow rate was analysed. All these parameters have a clear influence on the hydrogen production efficiency, which was described with such parameters as the hydrogen production rate [NL(H2/h] and the energy yield of hydrogen production [NL(H2/kWh]. The best achieved experimental results showed that the hydrogen production rate was up to 1116 NL(H2/h and the energy yield was 223 NL(H2 per kWh of absorbed microwave energy. The results were obtained in the case of isopropanol dry reforming. The presented catalyst-free microwave plasma method can be adapted for hydrogen production not only from ethanol, isopropanol and kerosene, but also from different other liquid compounds containing hydrogen, like gasoline, heavy oils and biofuels.

Temperature setting and thermal regulation system for liquid hydrogen bubble chamber; Systeme de mise en temperature et de regulation thermique de chambres a bulles a hydrogene liquide

Energy Technology Data Exchange (ETDEWEB)

Meyer, J; Prugne, P; Roubeau, P [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1961-07-01

Hydrogen bubble chamber cooling and constant temperature maintenance in the 25/28 deg. K, range by means of liquid hydrogen boiling under atmospheric pressure (20.4 deg. K) need a device, if possible automatic allowing the introduction of a variable amount of cold to counterbalance the heat transfer either static or due to the chamber operation. A variable impedance heat exchanger has been designed, built and experimented for this purpose. This device, which takes little space (less than 1000 cm{sup 3}) allows transfer of a variable cold power between 0 and 500 watts (0 to 50 liter of evaporated hydrogen). (author) [French] Pour le refroidissement des chambres a bulles a hydrogene et pour le maintien d'une temperature constante dans la gamme 25/28 deg. K au moyen d'hydrogene a l'ebullition sous pression atmospherique (20,4 deg. K), on a besoin d'un dispositif, si possible automatique, permettant l'introduction d'une quantite variable de froid pour compenser le transfert de chaleur, soit statique, soit du a l'operation de la chambre. Un echangeur de chaleur a impedance variable a ete concu, construit et essaye pour cet usage. Ce dispositif qui est peu encombrant (en dessous de 1000 cm{sup 3} ) permet le transfert d'une puissance frigorifique, variable entre 0 et 500 watts (0 a 50 litres d'hydrogene evapore). (auteur)

Comments on liquid hydrogen absorbers for MICE

International Nuclear Information System (INIS)

Green, Michael A.

2003-01-01

This report describes the heat transfer problems associated with a liquid hydrogen absorber for the MICE experiment. This report describes a technique for modeling heat transfer from the outside world, to the absorber case and in its vacuum vessel, to the hydrogen and then into helium gas at 14 K. Also presented are the equation for free convection cooling of the liquid hydrogen in the absorber

Resistance probe for liquid hydrogen

International Nuclear Information System (INIS)

Beauval, J.J.

1959-01-01

A simple device for determining the level of a liquid in equilibrium with its vapour is described. It makes use of the variation in heat exchange between a filament heated by a current and the atmosphere, on passing from the liquid to the gas. This apparatus is used to measure liquid hydrogen levels in liquefying dewar vessels. (author) [fr

Trace hydrogen extraction from liquid lithium tin alloy

International Nuclear Information System (INIS)

Xie Bo; Hu Rui; Xie Shuxian; Weng Kuiping

2010-01-01

In order to finish the design of tritium extraction system (TES) of fusion fission hybrid reactor (FFHR) tritium blanket, involving the dynamic mathematical model of liquid metal in contact with a gaseous atmosphere, approximate mathematical equation of tritium in lithium tin alloy was deduced. Moreover, carrying process used for trace hydrogen extraction from liquid lithium tin alloy was investigated with hydrogen being used to simulate tritium in the study. The study results indicate that carrying process is effective way for hydrogen extraction from liquid lithium tin alloy, and the best flow velocity of carrier gas is about 4 L/min under 1 kg alloy temperatures and carrying numbers are the main influencing factors of hydrogen number. Hydrogen extraction efficiency can reach 85% while the alloy sample is treated 6 times at 823 K. (authors)

Development of Automotive Liquid Hydrogen Storage Systems

Science.gov (United States)

Krainz, G.; Bartlok, G.; Bodner, P.; Casapicola, P.; Doeller, Ch.; Hofmeister, F.; Neubacher, E.; Zieger, A.

2004-06-01

Liquid hydrogen (LH2) takes up less storage volume than gas but requires cryogenic vessels. State-of-the-art applications for passenger vehicles consist of double-wall cylindrical tanks that hold a hydrogen storage mass of up to 10 kg. The preferred shell material of the tanks is stainless steel, since it is very resistant against hydrogen brittleness and shows negligible hydrogen permeation. Therefore, the weight of the whole tank system including valves and heat exchanger is more than 100 kg. The space between the inner and outer vessel is mainly used for thermal super-insulation purposes. Several layers of insulation foils and high vacuums of 10-3 Pa reduce the heat entry. The support structures, which keep the inner tank in position to the outer tank, are made of materials with low thermal conductivity, e.g. glass or carbon fiber reinforced plastics. The remaining heat in-leak leads to a boil-off rate of 1 to 3 percent per day. Active cooling systems to increase the stand-by time before evaporation losses occur are being studied. Currently, the production of several liquid hydrogen tanks that fulfill the draft of regulations of the European Integrated Hydrogen Project (EIHP) is being prepared. New concepts of lightweight liquid hydrogen storage tanks will be investigated.

Thermal properties of hydrogenated liquid natural rubber

Science.gov (United States)

Jamaluddin, Naharullah; Abdullah, Ibrahim; Yusoff, Siti Fairus M.

2015-09-01

Natural rubber (NR) was modified to form liquid natural rubber (LNR) via photooxidative degradation. Hydrogenated liquid natural rubber (HLNR) was synthesized by using diimide as source of hydrogen which the diimide is produced by thermolysis of p-toluenesulfonyl hydrazide (TSH). The structure of HLNR was characterized by determining the changes of main peaks in Fourier Transform infrared and nuclear magnetic resonance spectra after hydrogenation. Thermogravimetric analysis showed that the HLNR had higher decomposition temperature compared to LNR and the decomposition temperature is directly proportional to the percentage of conversion.

Thermal properties of hydrogenated liquid natural rubber

International Nuclear Information System (INIS)

Jamaluddin, Naharullah; Abdullah, Ibrahim; Yusoff, Siti Fairus M.

2015-01-01

Natural rubber (NR) was modified to form liquid natural rubber (LNR) via photooxidative degradation. Hydrogenated liquid natural rubber (HLNR) was synthesized by using diimide as source of hydrogen which the diimide is produced by thermolysis of p-toluenesulfonyl hydrazide (TSH). The structure of HLNR was characterized by determining the changes of main peaks in Fourier Transform infrared and nuclear magnetic resonance spectra after hydrogenation. Thermogravimetric analysis showed that the HLNR had higher decomposition temperature compared to LNR and the decomposition temperature is directly proportional to the percentage of conversion

Thermal properties of hydrogenated liquid natural rubber

Energy Technology Data Exchange (ETDEWEB)

Jamaluddin, Naharullah; Abdullah, Ibrahim; Yusoff, Siti Fairus M. [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

2015-09-25

Natural rubber (NR) was modified to form liquid natural rubber (LNR) via photooxidative degradation. Hydrogenated liquid natural rubber (HLNR) was synthesized by using diimide as source of hydrogen which the diimide is produced by thermolysis of p-toluenesulfonyl hydrazide (TSH). The structure of HLNR was characterized by determining the changes of main peaks in Fourier Transform infrared and nuclear magnetic resonance spectra after hydrogenation. Thermogravimetric analysis showed that the HLNR had higher decomposition temperature compared to LNR and the decomposition temperature is directly proportional to the percentage of conversion.

Scanning electrochemical microscopy determination of hydrogen flux at liquid|liquid interface with potentiometric probe

OpenAIRE

Jedraszko, Justyna; Nogala, Wojciech; Adamiak, Wojciech; Girault, Hubert H.; Opallo, Marcin

2014-01-01

Scanning electrochemical microscopy potentiometric determination of local hydrogen concentration and its flux next to the liquid|liquid interface was demonstrated. This method is based on the shift of open circuit potential of Pt-based reversible hydrogen electrode. The detection system was verified with a system generating hydrogen under galvanostatic conditions. Then, it was applied to aqueous|1,2-dichloroethane interface where hydrogen is produced with decamethylferrocene as electron donor.

Neutronic studies of a liquid hydrogen-water composite moderator

International Nuclear Information System (INIS)

Tahara, T.; Ooi, M.; Iwasa, H.; Kiyanagi, Y.; Iverson, E.B.; Crabtree, J.A.; Lucas, A.T.

2001-01-01

A liquid hydrogen-liquid water composite moderator may provide performance like liquid methane at high-power spallation sources where liquid methane is impractical. We have measured the neutronic properties of such a composite moderator, where a hydrogen layer 1.25 cm thick was closely backed by water layers of 1.75 cm and 3.75 cm thickness. We also studied a moderator in which a 1.75 cm water layer was closely backed by a 1.25 cm hydrogen layer. We further performed simulations for each of these systems for comparison to the experimental results. We observed enhancement of the spectral intensity in the 'thermal' energy range as compared to the spectrum from a conventional liquid hydrogen moderator. This enhancement grew more significant as the water thickness increased, although the pulse shapes became wider as well. (author)

Stability analysis of high temperature superconducting coil in liquid hydrogen

International Nuclear Information System (INIS)

Nakayama, T.; Yagai, T.; Tsuda, M.; Hamajima, T.

2007-01-01

Recently, it is expected that hydrogen plays an important role in energy source including electric power in near future. Liquid hydrogen has high potential for cooling down superconducting coil wound with high temperature superconductors (HTS), such as BSCCO, YBCO. In this paper, we study stabilities of the coils wound with BSCCO tapes, which are immersed in the liquid hydrogen, and compare stability results with those cooled by liquid helium. We treat a minimum propagation zone (MPZ) theory to evaluate the coil stability considering boiling heat flux of the liquid hydrogen, and specific heat, heat conduction and resistivity of HTS materials as a function of temperature. It is found that the coil cooled by the liquid hydrogen has higher stability margin than that cooled by the liquid helium. We compare the stability margins of both coils wound with Bi-2223/Ag tape and Bi-2212/Ag tape in liquid hydrogen. As a result, it is found that the stability of Bi-2212 coil is equivalent to that of Bi-2223 coil in low and high magnetic field, while the maximum current of Bi-2212 coil exceeds a little bit that of Bi-2223 coil in both magnetic fields

Structure and weak hydrogen bonds in liquid acetaldehyde

Directory of Open Access Journals (Sweden)

Cordeiro Maria A. M.

2004-01-01

Full Text Available Monte Carlo simulations have been performed to investigate the structure and hydrogen bonds formation in liquid acetaldehyde. An all atom model for the acetaldehyde have been optimized in the present work. Theoretical values obtained for heat of vaporisation and density of the liquid are in good agreement with experimental data. Graphics of radial distribution function indicate a well structured liquid compared to other similar dipolar organic liquids. Molecular mechanics minimization in gas phase leads to a trimer of very stable structure. The geometry of this complex is in very good agreement with the rdf. The shortest site-site correlation is between oxygen and the carbonyl hydrogen, suggesting that this correlation play a important role in the liquid structure and properties. The OxxxH average distance and the C-HxxxO angle obtained are characteristic of weak hydrogen bonds.

Hydrogen isotope separation in hydrophobic catalysts between hydrogen and liquid water

Energy Technology Data Exchange (ETDEWEB)

Ye, Linsen, E-mail: yls2005@mail.ustc.edu.cn [China Academy of Engineering Physics, Mianyang 621900 (China); Luo, Deli [Science and Technology on Surface Physics and Chemistry Laboratory, Jiangyou 621907 (China); Tang, Tao; Yang, Wan; Yang, Yong [China Academy of Engineering Physics, Mianyang 621900 (China)

2015-11-15

Hydrogen isotope catalytic exchange between hydrogen and liquid water is a very effective process for deuterium-depleted potable water production and heavy water detritiation. To improve the characteristics of hydrophobic catalysts for this type of reaction, foamed and cellular structures of hydrophobic carbon-supported platinum catalysts were successfully prepared. Separation of deuterium or tritium from liquid water was carried out by liquid-phase catalytic exchange. At a gas–liquid ratio of 1.53 and exchange temperature of 70 °C, the theoretical plate height of the hydrophobic catalyst (HETP = 34.2 cm) was slightly lower than previously reported values. Changing the concentration of the exchange column outlet water yielded nonlinear changes in the height of the packing layer. Configurations of deuterium-depleted potable water and detritiation of heavy water provide references for practical applications.

H2T liquid hydrogen delivery system

International Nuclear Information System (INIS)

Roy, S.

2002-01-01

This Power Point presentation provides a preliminary evaluation of the cost of delivering liquid hydrogen produced in Quebec to hydrogen fuelled cars in Germany. The presentation describes the chain of events regarding liquid hydrogen delivery, beginning with the production of hydrogen from an initial source of hydro power. Water passes through an electrolyzer where hydrogen is liquefied and then placed into a container which is transported to market via truck, rail or tanker. Once transported, the hydrogen fuel is made available for consumers at refueling stations. The paper lists the costs related to transportation with reference to safety rules, pure transportation costs, leasing fees for the containers, and permission of customs duties for the import of hydrogen and export of empty containers between Quebec and Germany. A graph depicting a typical refueling station in Germany and the refueling events per hour was presented. For safety reasons, refueling is performed by a refueling robot. A blueprint of safety and protection distances at a refueling station was also presented. tabs., figs

A liquid organic carrier of hydrogen as a fuel for automobiles

International Nuclear Information System (INIS)

Taube, M.; Taube, P.

1979-09-01

A system of storing energy in a hydrogen containing fuel for the motor car is discussed. The recyclable liquid chemical carrier is: (Methylcyclohexane (liquid)) dehydrogenation (Toluene (liquid)) + (hydrogen (gas)). The reverse reaction, the hydrogenation of toluene, occurs in a regional plant connected to a source of hydrogen (electrolysis of water) with a significant by-product being heat at 200 0 C for district heating. The system is able to store hydrogen in liquid form under ambient temperature and pressure even in a small motor car. The concentration of hydrogen is 6.1 % by weight. The release of gaseous hydrogen from the liquid methylcyclohexane needs a chemical catalytic reactor having a temperature of 300 0 C and a pressure of some bars. This reaction has been well studied. The thermal energy for the dehydrogenation is taken from the exhaust gases at 780 0 C. A layout of the most important processes of the system is given. (Auth.)

Hydrogen production from glucose in ionic liquids

Energy Technology Data Exchange (ETDEWEB)

Assenbaum, D.W.; Taccardi, N.; Berger, M.E.M.; Boesmann, A.; Enzenberger, F.; Woelfel, R.; Wasserscheid, P. [Erlangen-Nuernberg Univ. (Germany). Lehrstuhl fuer chemische Reaktionstechnik

2010-07-01

technologies suffer from the fact that the overall reaction rates are often restricted by mass and heat transport problems. Lastly, there are severe limitations concerning the feedstock selection as for some important substrates, such as e.g. glucose, the process can only be operated in very diluted systems to avoid rapid tar formation [22,23,24]. In this contribution we describe for the first time a catalytic reaction system producing hydrogen from glucose in astonishingly high selectivities using a single reaction step under very mild conditions. The catalytic reaction system is characterized by its homogeneous nature and comprises a Ru-complex catalyst dissolved and stabilized in an ionic liquid medium. Ionic liquids are salts of melting points below 100 C [25]. These liquid materials have attracted much interest in the last decade as solvents for catalytic reactions [26] and separation technologies (extraction, distillation) [27,28,29,30,31,32]. Besides, these liquids have found industrial applications as process fluids for mechanic [33] and electrochemical applications [34]. Finally, from the pioneering work of Rogers and co-workers, it is known that ionic liquids are able to dissolve significant amounts of water-insoluble biopolymers (such as e.g. cellulose and chitin)[35] and even complex biopolymer mixtures, such as e.g. wood, have been completely dissolved in some ionic liquids [36]. In our specific application, the role of the ionic liquid is threefold: a) the ionic liquid dissolves the carbohydrate starting material thus expanding the range of applicable carbohydrate to water insoluble polymers; b) the ionic liquid provides a medium to dissolve and stabilize the catalyst; c) the ionic liquid dissolves hydrogen at a very low level, so inhibiting any possible collateral hydrogen-consuming process (detailed investigation of the hydrogen solubility in ionic liquids have been reported by e.g. Brennecke and coworkers [37]). (orig.)

Pengaruh Growth Opportunity, Liquidity, Profitability, dan Tangibility terhadap Struktur Modal pada Perusahaan Manufaktur yang Terdaftar di Bursa Efek Indonesia

OpenAIRE

Harahap, Artika Hemdi

2015-01-01

Rumusan masalah dalam penelitian ini adalah bagaimana pengaruh komponen growth opportunity, liquidity, profitability, dan tangibility terhadap struktur modal pada perusahaan manufaktur yang terdaftar di Bursa Efek Indonesia (BEI). Tujuan penelitian ini adalah untuk mengetahui dan menganalisis pengaruh komponen growth opportunity, liquidity, profitability, dan tangibility terhadap struktur modal. Hipotesis dalam penelitian ini adalah komponen growth opportunity, liquidity, profitability, d...

Extraction and determination of hydrogen in uranium and zirconium; Extraction et dosage de l'hydrogene dans l'uranium et le zirconium

Energy Technology Data Exchange (ETDEWEB)

Champeix, L; Coblence, G; Darras, R [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

The method of desorption under vacuum at high temperatures in the solid phase, which gives good results in the case of steels, has been applied to uranium and zirconium. In these two metals hydrogen is found mainly in the form of hydride. It is chiefly a question of determining the most suitable temperature and the heating time necessary to obtain an almost total extraction of hydrogen. Two considerations must be taken into account in the choice of temperature. It should be such that on the one hand the hydride decomposes rapidly and completely at the reduced pressure applied, and on the other hand the diffusion of hydrogen through the metal takes place fairly quickly. The apparatus and the method used are described; systematic tests have led to the adoption of temperatures of 650 deg. C for uranium and 1050 deg. C for zirconium. (author) [French] La methode de desorption sous vide a chaud en phase solide, methode qui donne de bons resultats dans le cas des aciers, a ete appliquee a l'uranium et au zirconium. Dans ces deux metaux, l'hydrogene se trouve surtout a l'etat d'hydrure. Il s'agit essentiellement de determiner la temperature optimum et la duree du chauffage necessaire pour obtenir une extraction d'hydrogene pratiquement complete. Deux considerations interviennent dans le choix de la temperature. Elle doit etre telle que, d'une part la decomposition de l'hydrure se fasse rapidement et completement sous la pression reduite realisee et d'autre part que la diffusion de l'hydrogene a travers le metal soit assez rapide. L'appareil et le mode operatoire utilises sont decrits des essais systematiques ont conduit a adopter une temperature de 650 deg. C pour l'uranium et de 1050 deg. C pour le zirconium. (auteur)

Liquid-phase chemical hydrogen storage: catalytic hydrogen generation under ambient conditions.

Science.gov (United States)

Jiang, Hai-Long; Singh, Sanjay Kumar; Yan, Jun-Min; Zhang, Xin-Bo; Xu, Qiang

2010-05-25

There is a demand for a sufficient and sustainable energy supply. Hence, the search for applicable hydrogen storage materials is extremely important owing to the diversified merits of hydrogen energy. Lithium and sodium borohydride, ammonia borane, hydrazine, and formic acid have been extensively investigated as promising hydrogen storage materials based on their relatively high hydrogen content. Significant advances, such as hydrogen generation temperatures and reaction kinetics, have been made in the catalytic hydrolysis of aqueous lithium and sodium borohydride and ammonia borane as well as in the catalytic decomposition of hydrous hydrazine and formic acid. In this Minireview we briefly survey the research progresses in catalytic hydrogen generation from these liquid-phase chemical hydrogen storage materials.

Laser-induced separation of hydrogen isotopes in the liquid phase

International Nuclear Information System (INIS)

Beattie, W.; Freund, S.; Holland, R.; Maier, W.

1980-01-01

A process for separating hydrogen isotopes which comprises (A) forming a liquid phase of hydrogen-bearing feedstock compound at a temperature at which the spectral features of the feedstock compound are narrow enough or the absorption edges sharp enough to permit spectral features corresponding to the different hydrogen isotopes to be separated to be distinguished, (B) irradiating the liquid phase at said temperature with monochromatic radiation of a first wavelength which selectively or at least preferentially excites those molecules of said feedstock compound containing a first hydrogen isotope, and (C) subjecting the excited molecules to physical or chemical processes or a combination thereof whereby said first hydrogen isotope contained in said excited molecules is separated from other hydrogen isotopes contained in the unexcited molecules in said liquid phase

Detector for the liquid carried over in a gas; Detecteur d'entrainement de liquide dans un gaz

Energy Technology Data Exchange (ETDEWEB)

Delisle, J P; Eperonnat, P; Lions, N [Commissariat a l' Energie Atomique, Cadarache (France). Centre d' Etudes Nucleaires

1965-07-01

This report describes an optical detector for the detection of a liquid carried over by a gas. The device is sensitive to a cumulated quantity of liquid equal to a few cubic millimetres and is capable of operating an alarm from a distance. The prototype was constructed and tested as detector for the oil leaking in the argon compressed by a diaphragm compressor. A patent for this apparatus under the number: P.V.954.703, has been deposited on 22.11.1963. (authors) [French] Ce rapport decrit un detecteur optique d'entrainement de liquide dans un gaz, sensible a une quantite cumulee de liquide entraine egale a quelques millimetres cubes. L'appareil peut actionner une alarme a distance. Le prototype a ete construit et essaye comme detecteur de fuites d'huile dans l'argon refoule par un compresseur a membranes. Une demande de brevet a ete deposee pour cet appareil sous le numero: P.V.954.703, le 22.11.1963. (auteur)

Thermal and hydrodynamic study of a whirling liquid hydrogen layer under high heat flux; Etude thermique et hydrodynamique d'une couche tourbillonnaire d'hydrogenen liquide sous flux de chaleur eleve

Energy Technology Data Exchange (ETDEWEB)

Ewald, R [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1968-03-01

In order to achieve a cold neutrons source ({lambda} {>=} 4.10{sup -10} m) in a high flux reactor ({approx} 10{sup 15} neutrons/cm{sup 2}.s), a whirling liquid hydrogen layer (145 mm OD, effective thickness 15 mm, height about 180 mm) was formed, out-of-pile, in a cylindrical transparent glass vessel. The whirling motion was obtained by tangential injection of the liquid, near the wall. Thermal and hydrodynamical conditions of formation and laws of similarity of such a layer were studied. The characteristics of this whirling flow were observed as a function of mass flow rate (5 to 27 g/s; 4.3 to 23 l/mn), and of spillway width (18 and 25 mm). Six different nozzles were used : 1.0; 1.5; 1.9; 2.25; 2.65 and 3.0 mm ID. The total heat influx was found between 8.6 and 10.4 kW. The heat flux density was about 9.4 W/cm{sup 2} and the mean layer density around 80 per cent of that of the liquid hydrogen at 20.4 Kelvin. High speed movies were used to analyze the boiling regime. (author) [French] En vue de realiser une source de neutrons froids ({lambda} {>=} 4.10{sup -10} m) dans un reacteur a haut flux ({approx} 10{sup 15} neutrons thermiques/cm{sup 2}.s), on a forme dans un vase cylindrique transparent en verre, hors-pile, une couche tourbillonnaire ('vortex') d'hydrogene liquide (diametre exterieur 145 mm, epaisseur effective 15 mm, hauteur 180 mm environ). Le mouvement giratoire est obtenu par injection tangentielle du liquide pres de la paroi. L'etude porte sur la determination des conditions thermiques et hydrodynamiques de la formation d'une telle couche et sur les regles de similitude de ce phenomene. On a observe les caracteristiques de l'ecoulement giratoire en fonction du debit (de 5 a 27 g/s, soit de 4.3 a 23 1/mn), de la vitesse d'injection (entre 10 et 110 m/s) et de la largeur du deversoir (18 et 25 mm), ceci pour six diametres differents d'injecteur (1.0 ; 1.5; 1.9; 2.25; 2.65 et 3.0 mm). Le flux de chaleur total mesure est compris entre 8.6 et 10.4 kW et la

Mechanisms of dispersion during liquid hydrogen leakage

International Nuclear Information System (INIS)

Proust, C.; Gaston, D.

2000-01-01

INERIS conducts research programs with a mission of assessing and preventing accidental and chronic risks to people and the environment due to industrial plants, chemical substances and underground operation. This paper is a study of the dispersion mechanism of cryogenic hydrogen and the mechanisms of flame propagation in clouds of hydrogen. The objective is to contribute to the industrial control implementation of significant storage of hydrogen liquid that has pressure close to the atmospheric pressure. Within the framework of this program, the only interest is with the risk presented by escape of significant flow. This corresponds to accidental ruptures in tanks. The following four phases are looked at: the escape incident and the determination of the leak flow; the formation of the liquid layer and the vaporization of the hydrogen; the formation of the Hydrogen cloud in air; and the explosive ignition in the atmosphere, propagation of the explosive flame and evaluation of the pressure wave. This situation has been limited to dispersion in free air and does not consider the impact of containment

The kinetics of hydrogen removal from liquid sodium

International Nuclear Information System (INIS)

Gwyther, J.R.; Whittingham, A.C.

1981-01-01

The rates of hydrogen removal from liquid sodium-sodium hydride mixtures have been measured as a function of sodium stirring rate at temperatures up to 420 0 C. Two techniques have been employed - removal under continuous evacuation in which hydrogen flow rates were measured using a capillary flow technique and by argon purging in which hydrogen concentrations in the argon carrier gas were measured by gas chromatography. The results have been used to assess the feasibility of thermal decomposition of sodium hydride for the regeneration of hydride-laden LMFBR cold traps. Studies on the kinetics of desorption of hydrogen from solution in liquid sodium at temperatures up to 400 0 C are also presented and possible kinetic mechanisms discussed. (orig.)

The liquid hydrogen moderator at the NIST research reactor

International Nuclear Information System (INIS)

Williams, Robert E.; Rowe, J. Michael; Kopetka, Paul

1997-09-01

In 1995, the NIST research reactor was shut down for a number of modifications, including the replacement of the D 2 O cold neutron source with a liquid hydrogen moderator. When the liquid hydrogen source began operating, the flux of cold neutrons increased by a factor of six over the D 2 O source. The design and operation of the hydrogen source are described, and measurements of its performance are compared with the Monte Carlo simulations used in the design. (auth)

The reactions of oxygen and hydrogen with liquid sodium

International Nuclear Information System (INIS)

Ullmann, H.

1981-01-01

Results so far available as to the reactions and chemical equilibrium of oxygen and hydrogen with liquid sodium have been analyzed critically. The enthalpy values of the reactions have been discussed and supplemented on the basis of corresponding BORN-HABER cycles. The concentration and temperature functions of the hydrogen equilibrium pressure were deduced from experimental results. In relation to the solubility data the solid phases coexisting with liquid sodium in the ternary system Na-O-H have been discussed. The reaction of oxygen with hydrogen in diluted solution in liquid sodium has been investigated in more detail. Interaction coefficients, and the temperature functions of the free energy of formation and the equilibrium constant have been determined. (orig.)

Liquid hydrogen transfer pipes and level regulation systems

International Nuclear Information System (INIS)

Marquet, M.; Prugne, P.; Roubeau, P.

1961-01-01

Describes: 1) Transfer pipes - Plunging rods in liquid hydrogen Dewars; transfer pipes: knee-joint system for quick and accurate positioning of plunging Dewar rods; system's rods: combined valve and rod; valves are activated either by a bulb pressure or by a solenoid automatically or hand controlled. The latter allows intermittent filling. 2) Level regulating systems: Level bulbs: accurate to 1 or 4 m; maximum and minimum level bulbs: automatic control of the liquid hydrogen valve. (author) [fr

Modeling leaks from liquid hydrogen storage systems.

Energy Technology Data Exchange (ETDEWEB)

Winters, William Stanley, Jr.

2009-01-01

This report documents a series of models for describing intended and unintended discharges from liquid hydrogen storage systems. Typically these systems store hydrogen in the saturated state at approximately five to ten atmospheres. Some of models discussed here are equilibrium-based models that make use of the NIST thermodynamic models to specify the states of multiphase hydrogen and air-hydrogen mixtures. Two types of discharges are considered: slow leaks where hydrogen enters the ambient at atmospheric pressure and fast leaks where the hydrogen flow is usually choked and expands into the ambient through an underexpanded jet. In order to avoid the complexities of supersonic flow, a single Mach disk model is proposed for fast leaks that are choked. The velocity and state of hydrogen downstream of the Mach disk leads to a more tractable subsonic boundary condition. However, the hydrogen temperature exiting all leaks (fast or slow, from saturated liquid or saturated vapor) is approximately 20.4 K. At these temperatures, any entrained air would likely condense or even freeze leading to an air-hydrogen mixture that cannot be characterized by the REFPROP subroutines. For this reason a plug flow entrainment model is proposed to treat a short zone of initial entrainment and heating. The model predicts the quantity of entrained air required to bring the air-hydrogen mixture to a temperature of approximately 65 K at one atmosphere. At this temperature the mixture can be treated as a mixture of ideal gases and is much more amenable to modeling with Gaussian entrainment models and CFD codes. A Gaussian entrainment model is formulated to predict the trajectory and properties of a cold hydrogen jet leaking into ambient air. The model shows that similarity between two jets depends on the densimetric Froude number, density ratio and initial hydrogen concentration.

Liquid Hydrogen Sensor Considerations for Space Exploration

Science.gov (United States)

Moran, Matthew E.

2006-01-01

The on-orbit management of liquid hydrogen planned for the return to the moon will introduce new considerations not encountered in previous missions. This paper identifies critical liquid hydrogen sensing needs from the perspective of reliable on-orbit cryogenic fluid management, and contrasts the fundamental differences in fluid and thermodynamic behavior for ground-based versus on-orbit conditions. Opportunities for advanced sensor development and implementation are explored in the context of critical Exploration Architecture operations such as on-orbit storage, docking, and trans-lunar injection burn. Key sensing needs relative to these operations are also examined, including: liquid/vapor detection, thermodynamic condition monitoring, mass gauging, and leak detection. Finally, operational aspects of an integrated system health management approach are discussed to highlight the potential impact on mission success.

FINAL REPORT: Room Temperature Hydrogen Storage in Nano-Confined Liquids

Energy Technology Data Exchange (ETDEWEB)

VAJO, JOHN

2014-06-12

DOE continues to seek solid-state hydrogen storage materials with hydrogen densities of ≥6 wt% and ≥50 g/L that can deliver hydrogen and be recharged at room temperature and moderate pressures enabling widespread use in transportation applications. Meanwhile, development including vehicle engineering and delivery infrastructure continues for compressed-gas hydrogen storage systems. Although compressed gas storage avoids the materials-based issues associated with solid-state storage, achieving acceptable volumetric densities has been a persistent challenge. This project examined the possibility of developing storage materials that would be compatible with compressed gas storage technology based on enhanced hydrogen solubility in nano-confined liquid solvents. These materials would store hydrogen in molecular form eliminating many limitations of current solid-state materials while increasing the volumetric capacity of compressed hydrogen storage vessels. Experimental methods were developed to study hydrogen solubility in nano-confined liquids. These methods included 1) fabrication of composites comprised of volatile liquid solvents for hydrogen confined within the nano-sized pore volume of nanoporous scaffolds and 2) measuring the hydrogen uptake capacity of these composites without altering the composite composition. The hydrogen storage capacities of these nano-confined solvent/scaffold composites were compared with bulk solvents and with empty scaffolds. The solvents and scaffolds were varied to optimize the enhancement in hydrogen solubility that accompanies confinement of the solvent. In addition, computational simulations were performed to study the molecular-scale structure of liquid solvent when confined within an atomically realistic nano-sized pore of a model scaffold. Confined solvent was compared with similar simulations of bulk solvent. The results from the simulations were used to formulate a mechanism for the enhanced solubility and to guide the

Solubility of hydrogen isotopes in liquid LiPb

International Nuclear Information System (INIS)

Konishi, S.; Yamamoto, Y.; Noborio, K.; Calderoni, P.; Merrill, B.

2014-01-01

This research was performed mainly in the first half of the task 1-2 of TITAN project to investigate the interaction between hydrogen isotopes and liquid LiPb. Solubility of hydrogen in liquid LiPb was measured under a static condition. Kyoto University provided the first experimental apparatus shipped to Idaho, and Kyushu University succeeded the experiment and further improved. Obtained solubility generally agreed with some previous reports, but varied orders of magnitudes suggesting influence of impurity or other chemical processes. (author)

Hydrogenation of rapeseed oil for production of liquid bio-chemicals

International Nuclear Information System (INIS)

Pinto, F.; Martins, S.; Gonçalves, M.; Costa, P.; Gulyurtlu, I.; Alves, A.; Mendes, B.

2013-01-01

Highlights: ► Production of renewable liquid hydrocarbons through rapeseed oil hydrogenation. ► Hydrogenation at lower temperature and lower hydrogen pressures. ► Test of a catalyst commonly employed in petrochemical industry. ► Improve of hydrogenation process viability by decreasing operational costs. ► Analysis of hydrogenated product applications as bio-chemicals. -- Abstract: The main objective of rapeseed oil hydrogenation tests was the production of liquid bio-chemicals to be used as renewable raw material for the production of several chemicals and in chemical synthesis to substitute petroleum derived stuff. As, hydrogenation of vegetable oils is already applied for the production of biofuels, the work done focused in producing aromatic compounds, due to their economic value. The effect of experimental conditions on rapeseed oil hydrogenation was studied, namely, reaction temperature and time with the aim of selecting the most favourable conditions to convert rapeseed oil into liquid valuable bio-chemicals. Rapeseed oil was hydrogenated at a hydrogen initial pressure of 1.10 MPa. Reaction temperature varied in the range from 200 °C to 400 °C, while reaction times between 6 and 180 min were tested. The performance of a commercial cobalt and molybdenum catalyst was also studied. The highest hydrocarbons yields were obtained at the highest temperature and reaction times tested. At a temperature of 400 °C and at the reaction time of 120 min hydrocarbons yield was about 92% in catalyst presence, while in the absence of the catalyst this value decreased to 85%. Hydrocarbons yield was even higher when the reaction time of 180 min was used in the presence of catalyst, as the yield of 97% was observed. At these conditions hydrocarbons formed had a high content of aromatic compounds, around 50%. For this reason, the viscosity values of hydrogenated oils were lower than that established by EN590, which together with hydrogenated liquids composition

Kinetics of hydrogen release from dissolutions of ammonia borane in different ionic liquids

International Nuclear Information System (INIS)

Valero-Pedraza, María José; Martín-Cortés, Alexandra; Navarrete, Alexander; Bermejo, María Dolores; Martín, Ángel

2015-01-01

Ammonia borane is a promising hydrogen storage material that liberates hydrogen by thermolysis at moderate temperatures, but it also presents major limitations for practical applications including a long induction time before the initiation of hydrogen release and a difficult regeneration. Previous works have demonstrated that by dissolution of ammonia borane into several ionic liquids, and particularly in 1-butyl-3-methylimidazolium chloride bmimCl, the induction period at the beginning of the thermolysis is eliminated, but some problems persist, including foaming and the formation of a residue after thermolysis that is insoluble in the ionic liquid. In this work, the release of hydrogen from ammonia borane dissolved in different ionic liquids has been analyzed, measuring the kinetics of hydrogen release, visually following the evolution of the sample during the process using pressure glass tube reactors, and analyzing the residue by spectroscopic techniques. While dissolutions of ammonia borane in most ionic liquids analyzed show similar properties as dissolutions in bmimCl, using ionic liquids with bis(trifluoromethylsulfanyl)imide Tf_2N anion the foaming problem is reduced, and in some cases the residue remains dissolved in the ionic liquid, while with ionic liquids with choline anion higher hydrogen yields are achieved that indicate that the decomposition of ammonia borane proceeds through a different path. - Highlights: • Hydrogen release from ammonia borane dissolved in 13 ionic liquids has been studied. • Induction time is shortened and hydrogen release rate is accelerated in all cases. • The best results are obtained using ionic liquids with Tf_2N anion. • Ch cation ionic liquids enable higher H_2 yield, but cyclotriborazane is produced.

Thermal design study of a liquid hydrogen-cooled cold-neutron source

International Nuclear Information System (INIS)

Quach, D.; Aldredge, R.C.; Liu, H.B.; Richards, W.J.

2007-01-01

The use of both liquid hydrogen as a moderator and polycrystalline beryllium as a filter to enhance cold neutron flux at the UC Davis McClellan Nuclear Radiation Center has been studied. Although, more work is needed before an actual cold neutron source can be designed and built, the purpose of this preliminary study is to investigate the effects of liquid hydrogen and the thickness of a beryllium filter on the cold neutron flux generated. Liquid hydrogen is kept at 20 K, while the temperature of beryllium is assumed to be 77 K in this study. Results from Monte Carlo simulations show that adding a liquid hydrogen vessel around the beam tube can increase cold neutron flux by more than an order of magnitude. As the thickness of the liquid hydrogen layer increases up to about half an inch, the flux of cold neutrons also increases. Increasing the layer thickness to more than half an inch gives no significant enhancement of cold neutron flux. Although, the simulations show that the cold neutron flux is almost independent of the thickness of beryllium at 77 K, the fraction of cold neutrons does drop along the beam tube. This may be due to the fact that the beam tube is not shielded for neutrons coming directly from the reactor core. Further design studies are necessary for to achieve complete filtering of undesired neutrons. A simple comparison analysis based on heat transfer due to neutron scattering and gamma-ray heating shows that the beryllium filter has a larger rate of change of temperature and its temperature is higher. As a result heat will be transferred from beryllium to liquid hydrogen, so that keeping liquid hydrogen at the desired temperature will be the most important step in the cooling process

Alcohol-responsive, hydrogen-bonded, cholesteric liquid-crystal networks

NARCIS (Netherlands)

Chang, C.; Bastiaansen, C.W.M.; Broer, D.J.; Kuo, H.-L.

2012-01-01

Hydrogen-bridged, cholesteric liquid-crystal (CLC) polymer networks are adopted as an optical sensor material to distinguish between ethanol and methanol. Fast uptake of the alcohols is facilitated by an incorporated porosity created by breaking the hydrogen bridges and by a previously removed

Novel catalysts for isotopic exchange between hydrogen and liquid water

International Nuclear Information System (INIS)

Butler, J.P.; Rolston, J.H.; Stevens, W.H.

1978-01-01

Catalytic isotopic exchange between hydrogen and liquid water offers many inherent potential advantages for the separation of hydrogen isotopes which is of great importance in the Canadian nuclear program. Active catalysts for isotopic exchange between hydrogen and water vapor have long been available, but these catalysts are essentially inactive in the presence of liquid water. New, water-repellent platinum catalysts have been prepared by: (1) treating supported catalysts with silicone, (2) depositing platinum on inherently hydrophobic polymeric supports, and (3) treating platinized carbon with Teflon and bonding to a carrier. The activity of these catalysts for isotopic exchange between countercurrent streams of liquid water and hydrogen saturated with water vapor has been measured in a packed trickle bed integral reactor. The performance of these hydrophobic catalysts is compared with nonwetproofed catalysts. The mechanism of the overall exchange reaction is briefly discussed. 6 figures

Isotopic exchange between molecular hydrogen and liquid ammonia catalysed by alkali amides; Echange isotopique entre l'hydrogene moleculaire et l'ammoniac liquide catalyse par les amidures alcalins

Energy Technology Data Exchange (ETDEWEB)

Delmas, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-06-15

The catalytic action of alkali amides on the isotopic exchange between hydrogen and liquid ammonia has been reinvestigated. It was clear before this work that the reaction is homogeneous and first order with respect to the concentration of dissolved hydrogen, but the nature of the catalytic species was still subject to discussion. On one hand new precise kinetic measurements have been made with sodium, potassium, rubidium and cesium amide. On the other hand, the dissociation of these salts has been calculated with the help of the FUOSS-ONSAGER equation. If the rate of exchange is plotted as a function of the concentration of the free amide ion, a linear relationship is obtained. In our experimental conditions, primary salt effects are negligible and the concentration has to be used in the rate equations. This shows that only the free amide ion is acting as a catalytic species. Experiments on common ion effects and secondary salt effects support this conclusion. The results are in agreement with an associative mechanism. (author) [French] Une nouvelle etude de l'echange isotopique entre l'hydrogene et l'ammoniac liquide catalyse par les amidures alcalins a ete effectuee. II etait bien etabli avant le present travail que la reaction etait homogene et que sa vitesse etait du premier ordre par rapport a la concentration d'hydrogene dissous, mais la nature de l'espece catalytique etait encore controversee. De nouvelles mesures cinetiques precises ont ete faites avec les amidures de sodium, de potassium, de rubidium et de cesium. D'autre part, la dissociation de ces sels a ete calculee a l'aide de l'equation de FUOSS-ONSAGER. On constate que la vitesse d'echange est proportionnelle a la concentration de l'ion amidure libre. Dans nos conditions experimentales, les effets de sel primaires sont negligeables, l'equation de vitesse doit s'exprimer simplement en fonction des concentrations. Ceci indique que l'ion amidure libre est la seule espece catalytique. Des experiences d

Experiments on the thermalization of slow neutrons by liquid hydrogen (1962)

International Nuclear Information System (INIS)

Cribier, D.; Jacrot, B.; Lacaze, A.; Roubeau, P.

1962-01-01

In order to increase the flux of neutrons of long wave-length (λ > 4 A) emerging from a channel in the EL-3, a liquid hydrogen device was introduced into a channel of the reactor (Channel H 1 ). The principle of the device is simple. A volume of liquid hydrogen is introduced as close as possible to the reactor core into a region of intense isotropic flux. This hydrogen slows down the slow neutrons; because of the very small mean free diffusion path of slow in hydrogen, this slowing down is considerable even in a small volume of liquid hydrogen, and the spectrum temperature of neutrons emerging from the volume of liquid hydrogen can therefore be shifted. The intensity gain for neutrons with a wave length λ, is a G (λ) function which, for perfect thermalization and ignoring capture, is expressed by: G (λ) = 225 exp (- 45.3/λ 2 ), assuming a temperature of 300 deg. K for the neutrons before cooling and is 20 deg. K after cooling. For a wave-length of 5 A, the theoretical maximum gain of thus about 37. (authors) [fr

Study of the influence of the fast neutron spectrum on the production of defects in solids and liquids; Etude de l'influence du spectre des neutrons rapides sur la creation de defauts dans les solides et les liquides

Energy Technology Data Exchange (ETDEWEB)

Mas, P; Droulers, Y [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1964-07-01

In the first part of this work a calculation has been made of the number of defects formed in graphite by a given neutron flux having various spectral distributions. The defect formation function is that of KINCHIN and PEASE; its formulation is briefly given. An efficiency function is then defined for a fast neutron spectrum. This defects produced in a light water reactor and those produced in a graphite reactor. Finally an application of this method is given for comparing the defect forming tendency in graphite in the case of the reactor Melusine and of the reactor G-2 and G-3. In the second part are calculated the integrals for the energy release brought about by fast neutrons in carbon oxygen and hydrogen. In a region of 25 cm around the core of a swimming-pool type reactor these energy release integrals are approximately proportional to the neutron flux above 1 MeV. The determination of the energy released as a result of the passage of neutrons in organic liquids can therefore be reduced to the measurement of the flux above 1 MeV for the real spectral distribution. A calorimetric verification has been carried out in the case of water. (authors) [French] Dans la premiere partie de cette etude, on a calcule le nombre de defauts crees dans le graphite par un flux de neutrons donne, pris sous differents spectres. On a ainsi fait les calculs pour 4 spectres de pile. piscine et 2 spectres de pile au graphite. La fonction creation de defauts est celle de KINCHIN et PEASE. On rappelle brievement sa formulation. Puis on definit une fonction efficacite d'un spectre de neutrons rapides. Cette fonction permet alors d'etablir la relation entre defauts crees dans une pile a eau legere et defauts crees dans une pile au graphite. Enfin, une application de cette methode est donnee pour comparer l'aptitude a creer les defauts dans le graphite par la pile MELUSINE et les piles G-2 ou G-3. Dans la deuxieme partie, on a calcule les integrales de degagement d'energie provoque par

Study and Development of Face-Contact, Bellows Mechanical Seal for Liquid Hydrogen Turbopump

OpenAIRE

NOSAKA, Masataka; SUZUKI, Mineo; MIYAKAWA, Yukio; KAMIJO, Kenjiro; KIKUCHI, Masataka; MORI, Masahiro; 野坂, 正隆; 鈴木, 峰男; 宮川, 行雄; 上絛, 謙二郎; 菊池, 正孝; 森, 雅裕

1981-01-01

The development of a 10-ton thrust liquid oxygen and liquid hydrogen (LOX and LH2) rocket engine is under way at the National Space Development Agency. In advance of the development of a liquid hydrogen turbopump, the National Aerospace Laboratory carried out study and development of a face-contact, bellows mechanical seal for a liquid hydrogen turbopump in co-operation with the National Space Development Agency. The present report describes the fundamental experiments of the mechanical seal ...

Hydrogen meter for service in liquid sodium

International Nuclear Information System (INIS)

McCown, J.J.

1983-11-01

This standard establishes the requirements for the design, materials, fabrication, quality assurance, examination, and acceptance testing of a hydrogen meter and auxiliary equipment for use in radioactive or nonradioactive liquid sodium service. The meter shall provide a continuous and accurate indication of the hydrogen impurity concentration over the range 0.03 to 10 ppM hydrogen in sodium at temperatures between 800 and 1000 0 F (427 and 538 0 C). The meter may also be used to rapidly monitor changes in hydrogen concentration, over the same concentration range, and, therefore can be used as a sensor for sodium-water reactions in LMFBR steam generators

Ground Operations Demonstration Unit for Liquid Hydrogen Initial Test Results

Science.gov (United States)

Notardonato, W. U.; Johnson, W. L.; Swanger, A. M.; Tomsik, T.

2015-01-01

NASA operations for handling cryogens in ground support equipment have not changed substantially in 50 years, despite major technology advances in the field of cryogenics. NASA loses approximately 50% of the hydrogen purchased because of a continuous heat leak into ground and flight vessels, transient chill down of warm cryogenic equipment, liquid bleeds, and vent losses. NASA Kennedy Space Center (KSC) needs to develop energy-efficient cryogenic ground systems to minimize propellant losses, simplify operations, and reduce cost associated with hydrogen usage. The GODU LH2 project has designed, assembled, and started testing of a prototype storage and distribution system for liquid hydrogen that represents an advanced end-to-end cryogenic propellant system for a ground launch complex. The project has multiple objectives including zero loss storage and transfer, liquefaction of gaseous hydrogen, and densification of liquid hydrogen. The system is unique because it uses an integrated refrigeration and storage system (IRAS) to control the state of the fluid. This paper will present and discuss the results of the initial phase of testing of the GODU LH2 system.

Contribution to the study of hydrogenated and oxygenated impurities in liquid sodium; Contribution a l'etude des impuretees hydrogenees et oxygenees dans le sodium liquide

Energy Technology Data Exchange (ETDEWEB)

Naud, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-15

This study is made up essentially of two parts. The first is devoted to the development of dosage methods for selectively determining the oxygenated and hydrogenated impurities present in sodium, that is the oxide, the hydride and the hydroxide. The second makes use of these methods for a study of the Na-H{sub 2}-O{sub 2} system, as well as of the related problem of the attack of pyrex glass by molten sodium. The conventional method for dosing oxygen by amalgamation was first adapted to the simultaneous measurement of the hydride. We then developed a method for dosing the total hydrogen by measuring successively the concentrations of gas present in the hydride and hydroxide form. This method is based on the thermal decomposition of the hydride and the reaction between sodium and the hydroxide. Our contribution to the study of the Na-H{sub 2}-O{sub 2} System consists first of all in the study of the reaction between hydrogen and sodium in the temperature range from 150 to 250 deg C and at a pressure of about 150 mm of mercury. The study of the thermal decomposition of the hydride in sodium was then studied. It was possible to make some qualitative observations concerning the reaction between sodium and sodium hydroxide. Finally some complementary tests made it possible to define the nature of the phenomena occurring during the attack of pyrex glass by sodium. (author) [French] Cette etude comporte essentiellement deux parties. La premiere est consacree a la mise au point de methodes de dosages permettant de determiner selectivement les impuretes oxygenees et hydrogenees presentes dans le sodium, a savoir l'oxyde, l'hydrure et l'hydroxyde. La seconde met a profit ces methodes en vue de l'etude du systeme Na-H{sub 2}-O{sub 2}. ainsi que du phenomene connexe d'attaque du verre pyrex par le sodium fondu. La methode classique de dosage de l'oxygene par amalgamation a d'abord ete adaptee au dosage simultane de l'hydrure. Nous avons ensuite mis au point le dosage de l'hydrogene

Deuterium exchange between liquid water and gaseous hydrogen

International Nuclear Information System (INIS)

Dave, S.M.; Ghosh, S.K.; Sadhukhan, H.K.

1982-01-01

The overall separation factors for the deuterium exchange between liquid water and gaseous hydrogen have been calculated over a wide range of temperature, pressure and deuterium concentrations. These data would be useful in the design and other considerations for heavy water production, based on hydrogen-water exchange. (author)

Thermal and hydrodynamic study of a whirling liquid hydrogen layer under high heat flux; Etude thermique et hydrodynamique d'une couche tourbillonnaire d'hydrogenen liquide sous flux de chaleur eleve

Energy Technology Data Exchange (ETDEWEB)

Ewald, R. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1968-03-01

In order to achieve a cold neutrons source ({lambda} {>=} 4.10{sup -10} m) in a high flux reactor ({approx} 10{sup 15} neutrons/cm{sup 2}.s), a whirling liquid hydrogen layer (145 mm OD, effective thickness 15 mm, height about 180 mm) was formed, out-of-pile, in a cylindrical transparent glass vessel. The whirling motion was obtained by tangential injection of the liquid, near the wall. Thermal and hydrodynamical conditions of formation and laws of similarity of such a layer were studied. The characteristics of this whirling flow were observed as a function of mass flow rate (5 to 27 g/s; 4.3 to 23 l/mn), and of spillway width (18 and 25 mm). Six different nozzles were used : 1.0; 1.5; 1.9; 2.25; 2.65 and 3.0 mm ID. The total heat influx was found between 8.6 and 10.4 kW. The heat flux density was about 9.4 W/cm{sup 2} and the mean layer density around 80 per cent of that of the liquid hydrogen at 20.4 Kelvin. High speed movies were used to analyze the boiling regime. (author) [French] En vue de realiser une source de neutrons froids ({lambda} {>=} 4.10{sup -10} m) dans un reacteur a haut flux ({approx} 10{sup 15} neutrons thermiques/cm{sup 2}.s), on a forme dans un vase cylindrique transparent en verre, hors-pile, une couche tourbillonnaire ('vortex') d'hydrogene liquide (diametre exterieur 145 mm, epaisseur effective 15 mm, hauteur 180 mm environ). Le mouvement giratoire est obtenu par injection tangentielle du liquide pres de la paroi. L'etude porte sur la determination des conditions thermiques et hydrodynamiques de la formation d'une telle couche et sur les regles de similitude de ce phenomene. On a observe les caracteristiques de l'ecoulement giratoire en fonction du debit (de 5 a 27 g/s, soit de 4.3 a 23 1/mn), de la vitesse d'injection (entre 10 et 110 m/s) et de la largeur du deversoir (18 et 25 mm), ceci pour six diametres differents d'injecteur (1.0 ; 1.5; 1.9; 2.25; 2.65 et 3.0 mm). Le flux de chaleur total mesure

Modeling liquid hydrogen cavitating flow with the full cavitation model

Energy Technology Data Exchange (ETDEWEB)

Zhang, X.B.; Qiu, L.M.; Qi, H.; Zhang, X.J.; Gan, Z.H. [Institute of Refrigeration and Cryogenic Engineering, Zhejiang University, Hangzhou 310027 (China)

2008-12-15

Cavitation is the formation of vapor bubbles within a liquid where flow dynamics cause the local static pressure to drop below the vapor pressure. This paper strives towards developing an effective computational strategy to simulate liquid hydrogen cavitation relevant to liquid rocket propulsion applications. The aims are realized by performing a steady state computational fluid dynamic (CFD) study of liquid hydrogen flow over a 2D hydrofoil and an axisymmetric ogive in Hord's reports with a so-called full cavitation model. The thermodynamic effect was demonstrated with the assumption of thermal equilibrium between the gas phase and liquid phase. Temperature-dependent fluid thermodynamic properties were specified along the saturation line from the ''Gaspak 3.2'' databank. Justifiable agreement between the computed surface pressure, temperature and experimental data of Hord was obtained. Specifically, a global sensitivity analysis is performed to examine the sensitivity of the turbulent computations to the wall grid resolution, wall treatments and changes in model parameters. A proper near-wall model and grid resolution were suggested. The full cavitation model with default model parameters provided solutions with comparable accuracy to sheet cavitation in liquid hydrogen for the two geometries. (author)

Liquid composition having ammonia borane and decomposing to form hydrogen and liquid reaction product

Science.gov (United States)

Davis, Benjamin L; Rekken, Brian D

2014-04-01

Liquid compositions of ammonia borane and a suitably chosen amine borane material were prepared and subjected to conditions suitable for their thermal decomposition in a closed system that resulted in hydrogen and a liquid reaction product.

Stark broadening of hydrogen (1961); Sur l'effet stark dans les plasmas d'hydrogene (1961)

Energy Technology Data Exchange (ETDEWEB)

Fidone, I [Association Euratom-CEA Cadarache, 13 - Saint-Paul-lez-Durance (France)

1961-07-01

The effect of electron impacts on the Stark broadening of hydrogen atoms has been considered using a Debye-Huckel potential instead of a cut-off limit for the integrals giving the shift and the half-width. A slight difference results which in a typical case is of the order of 12 - 15 per cent. The simple adiabatic impact approximation has been used. (author) [French] L'effet des chocs electroniques sur l'elargissement Stark des raies d'hydrogene est calcule avec le potentiel de Debye-Huckel au lieu de l'emploi du cut-off pour les integrales qui donnent le deplacement et l'elargissement de la raie. On obtient une faible difference qui, dans un cas typique, est de l'ordre de grandeur de 12 - 15 pour cent. L'approximation adiabatique a ete employee pour decrire les chocs. (auteur)

Process for hydrogen isotope exchange and concentration between liquid water and hydrogen gas and catalyst assembly therefor

International Nuclear Information System (INIS)

Stevens, W.H.

1975-01-01

A bithermal, catalytic, hydrogen isotope exchange process between liquid water and hydrogen gas to effect concentration of the deuterium isotope of hydrogen is described. Liquid water and hydrogen gas are contacted with one another and with at least one catalytically active metal selected from Group VIII of the Periodic Table; the catalyst body has a water repellent, gas and water vapor permeable, organic polymer or resin coating, preferably a fluorinated olefin polymer or silicone resin coating, so that the isotope exchange takes place by two simultaneously occurring, and closely coupled in space, steps and concentration is effected by operating two interconnected sections containing catalyst at different temperatures. (U.S.)

Track formation in a liquid hydrogen ultrasonic bubble chamber

CERN Document Server

Brown, R C A; Jarman, P D

1973-01-01

Track sensitivity to minimum ionising particles has been demonstrated in liquid hydrogen using only an intense ultrasonic field. Carefully designed transducer systems are shown to be capable of producing pressure amplitudes >2.8 atm in a standing wave system in liquid hydrogen. The growth of bubbles to visible size (0.1 mm) in less than 0.2 ms, and their collapse in less than 15 ms, indicates that rapid cycling rates of 50-100 pulses per second may be feasible with this technique. (11 refs).

Heat Analysis of Liquid piston Compressor for Hydrogen Applications

DEFF Research Database (Denmark)

Kermani, Nasrin Arjomand; Rokni, Masoud

2014-01-01

A new hydrogen compression technology using liquid as the compression piston is investigated from heat transfer point of view. A thermodynamic model, simulating a single compression stroke, is developed to investigate the heat transfer phenomena inside the compression chamber. The model is develo......A new hydrogen compression technology using liquid as the compression piston is investigated from heat transfer point of view. A thermodynamic model, simulating a single compression stroke, is developed to investigate the heat transfer phenomena inside the compression chamber. The model...

Glass Bubbles Insulation for Liquid Hydrogen Storage Tanks

Science.gov (United States)

Sass, J. P.; SaintCyr, W. W.; Barrett, T. M.; Baumgartner, R. G.; Lott, J. W.; Fesmire, J. E.

2009-01-01

A full-scale field application of glass bubbles insulation has been demonstrated in a 218,000 L liquid hydrogen storage tank. This work is the evolution of extensive materials testing, laboratory scale testing, and system studies leading to the use of glass bubbles insulation as a cost efficient and high performance alternative in cryogenic storage tanks of any size. The tank utilized is part of a rocket propulsion test complex at the NASA Stennis Space Center and is a 1960's vintage spherical double wall tank with an evacuated annulus. The original perlite that was removed from the annulus was in pristine condition and showed no signs of deterioration or compaction. Test results show a significant reduction in liquid hydrogen boiloff when compared to recent baseline data prior to removal of the perlite insulation. The data also validates the previous laboratory scale testing (1000 L) and full-scale numerical modeling (3,200,000 L) of boiloff in spherical cryogenic storage tanks. The performance of the tank will continue to be monitored during operation of the tank over the coming years. KEYWORDS: Glass bubble, perlite, insulation, liquid hydrogen, storage tank.

Acoustically Forced Coaxial Hydrogen / Liquid Oxygen Jet Flames

Science.gov (United States)

2016-05-15

Conference Paper 3. DATES COVERED (From - To) 18 Mar 2016 – 15 May 2016 4. TITLE AND SUBTITLE Acoustically Forced Coaxial Hydrogen / Liquid Oxygen Jet...perform, display, or disclose the work. 13. SUPPLEMENTARY NOTES For presentation at 28th Annual Conference on Liquid Atomization and Spray Systems...serious problems in the development of liquid rocket engines. In order to understand and predict them, it is necessary to understand how representative

Warm Pressurant Gas Effects on the Liquid Hydrogen Bubble Point

Science.gov (United States)

Hartwig, Jason W.; McQuillen, John B.; Chato, David J.

2013-01-01

This paper presents experimental results for the liquid hydrogen bubble point tests using warm pressurant gases conducted at the Cryogenic Components Cell 7 facility at the NASA Glenn Research Center in Cleveland, Ohio. The purpose of the test series was to determine the effect of elevating the temperature of the pressurant gas on the performance of a liquid acquisition device. Three fine mesh screen samples (325 x 2300, 450 x 2750, 510 x 3600) were tested in liquid hydrogen using cold and warm noncondensible (gaseous helium) and condensable (gaseous hydrogen) pressurization schemes. Gases were conditioned from 0 to 90 K above the liquid temperature. Results clearly indicate a degradation in bubble point pressure using warm gas, with a greater reduction in performance using condensable over noncondensible pressurization. Degradation in the bubble point pressure is inversely proportional to screen porosity, as the coarsest mesh demonstrated the highest degradation. Results here have implication on both pressurization and LAD system design for all future cryogenic propulsion systems. A detailed review of historical heated gas tests is also presented for comparison to current results.

Microscopic dynamics and relaxation processes in liquid hydrogen fluoride

International Nuclear Information System (INIS)

Angelini, R.; Giura, P.; Monaco, G.; Sette, F.; Fioretto, D.; Ruocco, G.

2004-01-01

Inelastic x-ray scattering and Brillouin light scattering measurements of the dynamic structure factor of liquid hydrogen fluoride have been performed in the temperature range T=214-283 K. The data, analyzed using a viscoelastic model with a two time-scale memory function, show a positive dispersion of the sound velocity c(Q) between the low frequency value c 0 (Q) and the high frequency value c ∞α (Q). This finding confirms the existence of a structural (α) relaxation directly related to the dynamical organization of the hydrogen bonds network of the system. The activation energy E a of the process has been extracted by the analysis of the temperature behavior of the relaxation time τ α (T) that follows an Arrhenius law. The obtained value for E a , when compared with that observed in another hydrogen bond liquid as water, suggests that the main parameter governing the α-relaxation process is the number of hydrogen bonds per molecule

A three-cell liquid hydrogen target for an extended focal plane polarimeter

International Nuclear Information System (INIS)

Golovanov, L.B.; Borzounov, Yu.T.; Piskunov, N.M.; Tsvinev, A.P.

1996-01-01

This article describes the design and working principle of a 3-cell liquid hydrogen target produced for the high-energy deuteron polarimeter HYPOM. This target uses liquid Helium as a cooling agent. After a general description of the apparatus, tests and operating modes are thoroughly explained. In particular the air controlled self regulation of Helium flow in the cryostat to stabilize the liquid hydrogen level is presented. (author)

The use of infrared absorption to determine density of liquid hydrogen.

Science.gov (United States)

Unland, H. D.; Timmerhaus, K. D.; Kropschot, R. H.

1972-01-01

Experimental evaluation of the use of infrared absorption for determining the density of liquid hydrogen, and discussion of the feasibility of an airborne densitometer based on this concept. The results indicate that infrared absorption of liquid hydrogen is highly sensitive to the density of hydrogen, and, under the operating limitations of the equipment and experimental techniques used, the determined values proved to be repeatable to an accuracy of 2.7%. The desiderata and limitations of an in-flight density-determining device are outlined, and some of the feasibility problems are defined.

Notch Effect on Tensile Deformation Behavior of 304L and 316L Steels in Liquid Helium and Hydrogen

International Nuclear Information System (INIS)

Shibata, K.; Fujii, H.

2004-01-01

Tensile tests of type 304L and 316L steels were carried out using round bar specimens with a notch in liquid helium, hydrogen, liquid nitrogen and at ambient temperature. The obtained tensile strengths were compared with the tensile strengths of smooth specimens. For smooth specimens, tensile strength increased with a decrease in temperature and the strengths in liquid helium and hydrogen show similar values in both steels. For notched specimen of 304L steel, tensile strength (including fracture strength) increased noticeably from ambient to liquid nitrogen temperature but showed a large decrease in liquid helium and hydrogen. In liquid hydrogen and helium, the tensile strength is a little lower in liquid hydrogen than in liquid helium and both strengths are lower than tensile strengths of smooth specimens. For notched specimen of 316L steel, an increase in tensile strength from ambient to liquid nitrogen temperature was not so large and a decrease from liquid nitrogen to liquid hydrogen was small. The tensile strengths in liquid helium and hydrogen were nearly same and higher than those of smooth specimens. Different behavior of serration was observed between liquid helium and hydrogen, and between 304L and 316L steels. The reasons for these differences were discussed using computer simulation

Preliminary optimization experiments of coupled liquid hydrogen moderator for KENS-II

International Nuclear Information System (INIS)

Watanabe, N.; Kiyanagi, Y.; Inoue, K.; Furusaka, M.; Ikeda, S.; Arai, M.; Iwasa, H.

1989-01-01

As a preliminary optimization experiment on the cold-neutron source for KENS-II, energy and time distributions of cold neutrons emanating from coupled liquid-hydrogen moderators with and without a premoderator in a graphite reflector were measured and compared with those from a decoupled liquid-hydrogen moderator. The results showed that the energy spectra from the coupled liquid-hydrogen moderators are almost the same as those from a decoupled one. Relative gain of the former to the latter is fairly high, more than 5, and further increases with increasing wavelength. The broadening of the neutron pulse width in coupled moderators at the cold-neutron region is not so significant and only 1.5 times compared to the solid methane moderator presently operated at KENS-II. 2 refs., 12 figs., 1 tab

Electrokinetic Hydrogen Generation from Liquid WaterMicrojets

Energy Technology Data Exchange (ETDEWEB)

Duffin, Andrew M.; Saykally, Richard J.

2007-05-31

We describe a method for generating molecular hydrogen directly from the charge separation effected via rapid flow of liquid water through a metal orifice, wherein the input energy is the hydrostatic pressure times the volume flow rate. Both electrokinetic currents and hydrogen production rates are shown to follow simple equations derived from the overlap of the fluid velocity gradient and the anisotropic charge distribution resulting from selective adsorption of hydroxide ions to the nozzle surface. Pressure-driven fluid flow shears away the charge balancing hydronium ions from the diffuse double layer and carries them out of the aperture. Downstream neutralization of the excess protons at a grounded target electrode produces gaseous hydrogen molecules. The hydrogen production efficiency is currently very low (ca. 10-6) for a single cylindrical jet, but can be improved with design changes.

Hydrogenation of liquid natural rubber via diimide reduction in hydrazine hydrate/hydrogen peroxide system

International Nuclear Information System (INIS)

Yusof, Muhammad Jefri Mohd; Jamaluddin, Naharullah; Abdullah, Ibrahim; Yusoff, Siti Fairus M.

2015-01-01

Liquid natural rubber (LNR) with molecular weight of lower than 10 5 and shorter polymeric chain than natural rubber was prepared. LNR was then hydrogenated via diimide reduction by oxidation of hydrazine hydrate with hydrogen peroxide. The unsaturated units of the rubber were converted into saturated hydrocarbon to strengthen the backbone of the polymer so it was able to resist thermal degradation. The results indicated that hydrogenation degree of the product (HLNR) could be extended to 91.2% conversion under appropriate conditions. The hydrogenated LNR (HLNR) was characterized using Fourier-Transform Infrared (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopy. The physical characteristics of HLNR were analyzed with Termogravimetric Analysis (TGA)

Hydrogenation of liquid natural rubber via diimide reduction in hydrazine hydrate/hydrogen peroxide system

Science.gov (United States)

Yusof, Muhammad Jefri Mohd; Jamaluddin, Naharullah; Abdullah, Ibrahim; Yusoff, Siti Fairus M.

2015-09-01

Liquid natural rubber (LNR) with molecular weight of lower than 105 and shorter polymeric chain than natural rubber was prepared. LNR was then hydrogenated via diimide reduction by oxidation of hydrazine hydrate with hydrogen peroxide. The unsaturated units of the rubber were converted into saturated hydrocarbon to strengthen the backbone of the polymer so it was able to resist thermal degradation. The results indicated that hydrogenation degree of the product (HLNR) could be extended to 91.2% conversion under appropriate conditions. The hydrogenated LNR (HLNR) was characterized using Fourier-Transform Infrared (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopy. The physical characteristics of HLNR were analyzed with Termogravimetric Analysis (TGA).

Hydrogenation of liquid natural rubber via diimide reduction in hydrazine hydrate/hydrogen peroxide system

Energy Technology Data Exchange (ETDEWEB)

Yusof, Muhammad Jefri Mohd; Jamaluddin, Naharullah; Abdullah, Ibrahim; Yusoff, Siti Fairus M. [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

2015-09-25

Liquid natural rubber (LNR) with molecular weight of lower than 10{sup 5} and shorter polymeric chain than natural rubber was prepared. LNR was then hydrogenated via diimide reduction by oxidation of hydrazine hydrate with hydrogen peroxide. The unsaturated units of the rubber were converted into saturated hydrocarbon to strengthen the backbone of the polymer so it was able to resist thermal degradation. The results indicated that hydrogenation degree of the product (HLNR) could be extended to 91.2% conversion under appropriate conditions. The hydrogenated LNR (HLNR) was characterized using Fourier-Transform Infrared (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopy. The physical characteristics of HLNR were analyzed with Termogravimetric Analysis (TGA)

Measurement of scattering cross sections of liquid and solid hydrogen, deuterium and deuterium hydride for thermal neutrons

International Nuclear Information System (INIS)

Seiffert, W.D.

1984-01-01

The scattering cross sections for liquid and solid normal hydrogen, para-hydrogen, deuterium and deuterium hydride were measured for thermal neutrons at various temperatures. Solid samples of para-hydrogen exhibit distinct Bragg scattering. Liquid samples of deuterium and para-hydrogen also exhibit distinct coherence phenomena, which is indicative of strong local ordering of the molecules. In para-hydrogen and deuterium hydride, the threshold for scattering with excitation of rotations is distinctly visible. The positions of the thresholds show that the molecules in liquid hydrogen are not unhindered in their movement. After the beginning of the rotational excitation the scattering cross sections of liquid and solid para-hydrogen have different shapes which is to be explained by the differences in the dynamics of the liquid and the solid specimen. 22 references

Screen Channel Liquid Acquisition Device Outflow Tests in Liquid Hydrogen

Science.gov (United States)

Hartwig, Jason W.; Chato, David J.; McQuillen, J. B.; Vera, J.; Kudlac, M. T.; Quinn, F. D.

2013-01-01

This paper presents experimental design and test results of the recently concluded 1-g inverted vertical outflow testing of two 325x2300 full scale liquid acquisition device (LAD) channels in liquid hydrogen (LH2). One of the channels had a perforated plate and internal cooling from a thermodynamic vent system (TVS) to enhance performance. The LADs were mounted in a tank to simulate 1-g outflow over a wide range of LH2 temperatures (20.3 - 24.2 K), pressures (100 - 350 kPa), and flow rates (0.010 - 0.055 kg/s). Results indicate that the breakdown point is dominated by liquid temperature, with a second order dependence on mass flow rate through the LAD. The best performance is always achieved in the coldest liquid states for both channels, consistent with bubble point theory. Higher flow rates cause the standard channel to break down relatively earlier than the TVS cooled channel. Both the internal TVS heat exchanger and subcooling the liquid in the propellant tank are shown to significantly improve LAD performance.

Hydrogen permeation resistant layers for liquid metal reactors

International Nuclear Information System (INIS)

McGuire, J.C.

1980-03-01

Reviewing the literature in the tritium diffusion field one can readily see a wide divergence in results for both the response of permeation rate to pressure, and the effect of oxide layers on total permeation rates. The basic mechanism of protective oxide layers is discussed. Two coatings which are less hydrogen permeable than the best naturally occurring oxide are described. The work described is part of an HEDL-ANL cooperative research program on Tritium Permeation in Liquid Metal Cooled Reactors. This includes permeation work on hydrogen, deuterium, and tritium with the hydrogen-deuterium research leading to the developments presented

Liquid Hydrogen Recirculation System for Forced Flow Cooling Test of Superconducting Conductors

Science.gov (United States)

Shirai, Y.; Kainuma, T.; Shigeta, H.; Shiotsu, M.; Tatsumoto, H.; Naruo, Y.; Kobayashi, H.; Nonaka, S.; Inatani, Y.; Yoshinaga, S.

2017-12-01

The knowledge of forced flow heat transfer characteristics of liquid hydrogen (LH2) is important and necessary for design and cooling analysis of high critical temperature superconducting devices. However, there are few test facilities available for LH2 forced flow cooling for superconductors. A test system to provide a LH2 forced flow (∼10 m/s) of a short period (less than 100 s) has been developed. The test system was composed of two LH2 tanks connected by a transfer line with a controllable valve, in which the forced flow rate and its period were limited by the storage capacity of tanks. In this paper, a liquid hydrogen recirculation system, which was designed and fabricated in order to study characteristics of superconducting cables in a stable forced flow of liquid hydrogen for longer period, was described. This LH2 loop system consists of a centrifugal pump with dynamic gas bearings, a heat exchanger which is immersed in a liquid hydrogen tank, and a buffer tank where a test section (superconducting wires or cables) is set. The buffer tank has LHe cooled superconducting magnet which can produce an external magnetic field (up to 7T) at the test section. A performance test was conducted. The maximum flow rate was 43.7 g/s. The lowest temperature was 22.5 K. It was confirmed that the liquid hydrogen can stably circulate for 7 hours.

Motor fuels by hydrogenation of liquid hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1938-05-07

A process is disclosed for the production of knock-stable low-boiling motor fuels by conversion of liquid hydrocarbons which are vaporizable under the reaction conditions, which comprises passing the initial material at a temperature above 380/sup 0/C in a true vapor phase under pressure of more than 40 atmospheres together with hydrogen and gaseous hydrocarbons containing more than 1 carbon atom in the molecule in an amount by volume larger than that of the hydrogen over catalysts stable to poisoning stationarily confined in the reaction vessel.

Hydrogen utilization international clean energy system technology (WE-NET). Subtask 5. Development of technology of hydrogen transportation/storage (3rd edition, development of liquid hydrogen storage equipment, report on results of Air Liquide); Suiso riyo kokusai clean energy system gijutsu (WE-NET). Subtask 5. Suiso yuso chozo gijutsu no kaihatsu (daisanpen ekitai suiso chozo setsubi no kaihatsu Air Liquide sha seika hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In the fiscal 1995 study, items were searched which are keys to the design of a liquid hydrogen tanker of a capacity of 200,000m{sup 3}. Among those, the basic concepts were summarized which are necessary for the design of a liquid hydrogen tanker in terms of safety, and the extraporation of the existing low temperature technology into the large liquid hydrogen tank was studied. When adopting safety conditions of IGC Code applied to LNG to the liquid hydrogen tanker, it is necessary to limit the discharge amount of hydrogen to 3 kg/s. When considering safety at fire, for keeping safety of the same level as that of the LNG tanker, it is not appropriate to adopt the conventional vacuum insulation liquid hydrogen tank. In the fiscal 1995 study, 7 kinds of concept of the insulation structure were assumed, and it was concluded that BOR of 0.04-0.23/d was obtained. Also in fiscal 1996, the large liquid hydrogen tank was studied. For insulation of the large liquid hydrogen tank, the structure is most promising where AEROSIL bag or homogeneous AEROSIL is substituted for a forming heat insulating material of 4 design, but further study is needed for selection of the optimum heat insulating structure. 9 figs., 6 tabs.

Liquid hydrogen production and economics for NASA Kennedy Space Center

Science.gov (United States)

Block, D. L.

1985-12-01

Detailed economic analyses for the production of liquid hydrogen used to power the Space Shuttle are presented. The hydrogen production and energy needs of the NASA Kennedy Space Center are reviewed, and steam reformation, polygeneration, and electrolysis for liquid hydrogen production are examined on an equal economic basis. The use of photovoltaics as an electrolysis power source is considered. The 1985 present worth is calculated based on life cycle costs over a 21-year period beginning with full operation in 1990. Two different sets of escalation, inflation, and discount rates are used, with revenue credit being given for energy or other products of the hydrogen production process. The results show that the economic analyses are very dependent on the escalation rates used. The least net present value is found for steam reformation of natural gas, while the best net present value is found for the electrolysis process which includes the phasing of photovoltaics.

EFFECT OF HYDROGENATED, LIQUID AND GHEE OILS ON SERUM LI-PIDS PROFILE

Directory of Open Access Journals (Sweden)

Noushin Mohammadifard

2010-11-01

Full Text Available BACKGROUND: Trans fatty acids are known as the most harmful type of dietary fats, so this study was done to compare the effects of hydrogenated, liquid and ghee oils on serum lipids profile of healthy adults.    METHODS: This study was a randomized clinical trial conducted on 129 healthy participants aged from 20 to 60 years old who were beneficiaries of Imam-e-Zaman charitable organization. Subjects were randomly divided into 3 groups and each group was treated with a diet containing cooking and frying liquid, ghee, or hydrogenated for 40 days. Fasting serum lipids, including total cholesterol (TC, triglyceride (TG, LDL-cholesterol (LDL-C, HDL-cholesterol (HDL-C, apoprotein A (Apo A, and apoprotein B (Apo B were measured before and after the study.    RESULTS: TC, TG and Apo B had a significant reduction in the liquid oil group compared to the hydrogenated oil group. In the ghee group TG declined and Apo A increased significantly (p < 0.01. Liquid oil group had a significant reduction in HDL-C, compared to the ghee oil group (P < 0.05.     CONCLUSION: It was concluded that consuming liquid oil along with frying oil caused to reduce all serum lipid levels. However, ghee oil only reduced TG and increased HDL-C levels.      Keywords: Serum lipids, Apoproteins, Liquid oil, Hydrogenated oil, Ghee, Clinical trial

Time-resolved crystallization of deeply cooled liquid hydrogen isotopes

Energy Technology Data Exchange (ETDEWEB)

Kuehnel, Matthias

2014-02-15

This thesis serves two main purposes: 1. The introduction of a novel experimental method to investigate phase change dynamics of supercooled liquids 2. First-time measurements for the crystallization behaviour for hydrogen isotopes under various conditions (1) The new method is established by the synergy of a liquid microjet of ∼ 5 μm diameter and a scattering technique with high spatial resolution, here linear Raman spectroscopy. Due to the high directional stability and the known velocity of the liquid filament, its traveling axis corresponds to a time axis static in space. Utilizing evaporative cooling in a vacuum environment, the propagating liquid cools down rapidly and eventually experiences a phase transition to the crystalline state. This temporal evolution is probed along the filament axis, ultimately resulting in a time resolution of 10 ns. The feasibility of this approach is proven successfully within the following experiments. (2) A main object of study are para-hydrogen liquid filaments. Raman spectra reveal a temperature gradient of the liquid across the filament. This behaviour can quantitatively be reconstructed by numerical simulations using a layered model and is rooted in the effectiveness of evaporative cooling on the surface and a finite thermal conductivity. The deepest supercoolings achieved are ∼ 30% below the melting point, at which the filament starts to solidify from the surface towards the core. With a crystal growth velocity extracted from the data the appropriate growth mechanism is identified. The crystal structure that initially forms is metastable and probably the result of Ostwald's rule of stages. Indications for a transition within the solid towards the stable equilibrium phase support this interpretation. The analog isotope ortho-deuterium is evidenced to behave qualitatively similar with quantitative differences being mass related. In further measurements, isotopic mixtures of para-hydrogen and ortho-deuterium are

Time-resolved crystallization of deeply cooled liquid hydrogen isotopes

International Nuclear Information System (INIS)

Kuehnel, Matthias

2014-02-01

This thesis serves two main purposes: 1. The introduction of a novel experimental method to investigate phase change dynamics of supercooled liquids 2. First-time measurements for the crystallization behaviour for hydrogen isotopes under various conditions (1) The new method is established by the synergy of a liquid microjet of ∼ 5 μm diameter and a scattering technique with high spatial resolution, here linear Raman spectroscopy. Due to the high directional stability and the known velocity of the liquid filament, its traveling axis corresponds to a time axis static in space. Utilizing evaporative cooling in a vacuum environment, the propagating liquid cools down rapidly and eventually experiences a phase transition to the crystalline state. This temporal evolution is probed along the filament axis, ultimately resulting in a time resolution of 10 ns. The feasibility of this approach is proven successfully within the following experiments. (2) A main object of study are para-hydrogen liquid filaments. Raman spectra reveal a temperature gradient of the liquid across the filament. This behaviour can quantitatively be reconstructed by numerical simulations using a layered model and is rooted in the effectiveness of evaporative cooling on the surface and a finite thermal conductivity. The deepest supercoolings achieved are ∼ 30% below the melting point, at which the filament starts to solidify from the surface towards the core. With a crystal growth velocity extracted from the data the appropriate growth mechanism is identified. The crystal structure that initially forms is metastable and probably the result of Ostwald's rule of stages. Indications for a transition within the solid towards the stable equilibrium phase support this interpretation. The analog isotope ortho-deuterium is evidenced to behave qualitatively similar with quantitative differences being mass related. In further measurements, isotopic mixtures of para-hydrogen and ortho-deuterium are

Time-resolved crystallization of deeply cooled liquid hydrogen isotopes

Energy Technology Data Exchange (ETDEWEB)

Kuehnel, Matthias

2014-02-15

This thesis serves two main purposes: 1. The introduction of a novel experimental method to investigate phase change dynamics of supercooled liquids 2. First-time measurements for the crystallization behaviour for hydrogen isotopes under various conditions (1) The new method is established by the synergy of a liquid microjet of ∼ 5 μm diameter and a scattering technique with high spatial resolution, here linear Raman spectroscopy. Due to the high directional stability and the known velocity of the liquid filament, its traveling axis corresponds to a time axis static in space. Utilizing evaporative cooling in a vacuum environment, the propagating liquid cools down rapidly and eventually experiences a phase transition to the crystalline state. This temporal evolution is probed along the filament axis, ultimately resulting in a time resolution of 10 ns. The feasibility of this approach is proven successfully within the following experiments. (2) A main object of study are para-hydrogen liquid filaments. Raman spectra reveal a temperature gradient of the liquid across the filament. This behaviour can quantitatively be reconstructed by numerical simulations using a layered model and is rooted in the effectiveness of evaporative cooling on the surface and a finite thermal conductivity. The deepest supercoolings achieved are ∼ 30% below the melting point, at which the filament starts to solidify from the surface towards the core. With a crystal growth velocity extracted from the data the appropriate growth mechanism is identified. The crystal structure that initially forms is metastable and probably the result of Ostwald's rule of stages. Indications for a transition within the solid towards the stable equilibrium phase support this interpretation. The analog isotope ortho-deuterium is evidenced to behave qualitatively similar with quantitative differences being mass related. In further measurements, isotopic mixtures of para-hydrogen and ortho-deuterium are

Hydrogen and helium recycling from stirred liquid lithium under steady state plasma bombardment

Energy Technology Data Exchange (ETDEWEB)

Hirooka, Yoshi, E-mail: hirooka.yoshihiko@nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); The Graduate School for Advanced Studies, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Zhou, Haishan [The Graduate School for Advanced Studies, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Ono, Masa [Princeton Plasma Physics Laboratory, PO Box 451, Princeton, NJ 08543 (United States)

2014-12-15

For improved core performance via edge plasma-wall boundary control, solid and liquid lithium has been used as a plasma-facing material in a number of confinement experiments over the past several decades. Unfortunately, it is unavoidable that lithium is saturated in the surface region with implanted hydrogenic species as well as oxygen-containing impurities. For steady state operation, a flowing liquid lithium divertor with forced convection would probably be required. In the present work, the effects of liquid stirring to simulate forced convection have been investigated on the behavior of hydrogen and helium recycling from molten lithium at temperatures up to ∼350 °C. Data indicate that liquid stirring reactivates hydrogen pumping via surface de-saturation and/or uncovering impurity films, but can also induce helium release via surface temperature change.

An assessment of the government liquid hydrogen requirements for the 1995-2005 time frame including addendum, liquid hydrogen production and commercial demand in the United States

Science.gov (United States)

Bain, Addison

1990-01-01

Liquid hydrogen will continue to be an integral element in virtually every major space program, and it has also become a significant merchant product for certain commercial markets. Liquid hydrogen is not a universally available commodity, and the number of supply sources historically have been limited to regions having concentrated consumption patterns. With the increased space program activity it becomes necessary to assess all future programs on a collective and unified basis. An initial attempt to identify projected requirements on a long range basis is presented.

Comparison of alternate fuels for aircraft. [liquid hydrogen, liquid methane, and synthetic aviation kerosene

Science.gov (United States)

Witcofski, R. D.

1979-01-01

Liquid hydrogen, liquid methane, and synthetic aviation kerosene were assessed as alternate fuels for aircraft in terms of cost, capital requirements, and energy resource utilization. Fuel transmission and airport storage and distribution facilities are considered. Environmental emissions and safety aspects of fuel selection are discussed and detailed descriptions of various fuel production and liquefaction processes are given. Technological deficiencies are identified.

Performance Gains of Propellant Management Devices for Liquid Hydrogen Depots

Science.gov (United States)

Hartwig, Jason W.; McQuillen, John B.; Chato, David J.

2013-01-01

This paper presents background, experimental design, and preliminary experimental results for the liquid hydrogen bubble point tests conducted at the Cryogenic Components Cell 7 facility at the NASA Glenn Research Center in Cleveland, Ohio. The purpose of the test series was to investigate the parameters that affect liquid acquisition device (LAD) performance in a liquid hydrogen (LH2) propellant tank, to mitigate risk in the final design of the LAD for the Cryogenic Propellant Storage and Transfer Technology Demonstration Mission, and to provide insight into optimal LAD operation for future LH2 depots. Preliminary test results show an increase in performance and screen retention over the low reference LH2 bubble point value for a 325 2300 screen in three separate ways, thus improving fundamental LH2 LAD performance. By using a finer mesh screen, operating at a colder liquid temperature, and pressurizing with a noncondensible pressurant gas, a significant increase in margin is achieved in bubble point pressure for LH2 screen channel LADs.

Detection of hydrogen buildup in initially pure nonhydrogenous liquids

International Nuclear Information System (INIS)

McNeany, S.R.; Jenkins, J.D.

1978-12-01

A technique for monitoring hydrogen buildup in initially pure nonhydrogenous liquids is described in this report. The detection method is based upon the neutron-moderating properties of hydrogen. The analysis leading to the selection and design of a hydrogen-monitoring device is described. An experimental mockup of the device was then constructed and tested for hydrogen sensitivity. A hot cell was used for these tests. A device proved capable of measuring hydrogen concentrations in the range of 0 to 13.0 x 10 27 atoms/m 3 , with an accuracy of about 1.0 x 10 27 atoms/m 3 . A typical measurement can be made in 3 to 5 min. The experimental results confirmed the sensitivities predicted by the analysis and demonstrated that such a device would be practical for hydrogen concentration measurements for criticality control in an HTGR fuel refabrication plant

Integrated Refrigeration and Storage for Advanced Liquid Hydrogen Operations

Science.gov (United States)

Swanger, A. M.; Notardonato, W. U.; Johnson, W. L.; Tomsik, T. M.

2016-01-01

NASA has used liquefied hydrogen (LH2) on a large scale since the beginning of the space program as fuel for the Centaur and Apollo upper stages, and more recently to feed the three space shuttle main engines. The LH2 systems currently in place at the Kennedy Space Center (KSC) launch pads are aging and inefficient compared to the state-of-the-art. Therefore, the need exists to explore advanced technologies and operations that can drive commodity costs down, and provide increased capabilities. The Ground Operations Demonstration Unit for Liquid Hydrogen (GODU-LH2) was developed at KSC to pursue these goals by demonstrating active thermal control of the propellant state by direct removal of heat using a cryocooler. The project has multiple objectives including zero loss storage and transfer, liquefaction of gaseous hydrogen, and densification of liquid hydrogen. The key technology challenge was efficiently integrating the cryogenic refrigerator into the LH2 storage tank. A Linde LR1620 Brayton cycle refrigerator is used to produce up to 900W cooling at 20K, circulating approximately 22 g/s gaseous helium through the hydrogen via approximately 300 m of heat exchanger tubing. The GODU-LH2 system is fully operational, and is currently under test. This paper will discuss the design features of the refrigerator and storage system, as well as the current test results.

Power generation in fuel cells using liquid methanol and hydrogen peroxide

Science.gov (United States)

Narayanan, Sekharipuram R. (Inventor); Valdez, Thomas I. (Inventor); Chun, William (Inventor)

2002-01-01

The invention is directed to an encapsulated fuel cell including a methanol source that feeds liquid methanol (CH.sub.3 OH) to an anode. The anode is electrical communication with a load that provides electrical power. The fuel cell also includes a hydrogen peroxide source that feeds liquid hydrogen peroxide (H.sub.2 O.sub.2) to the cathode. The cathode is also in communication with the electrical load. The anode and cathode are in contact with and separated by a proton-conducting polymer electrolyte membrane.

Liquid Hydrogen Consumption During Space Shuttle Program

Science.gov (United States)

Partridge, Jonathan K.

2011-01-01

This slide presentation reviews the issue of liquid hydrogen consumption and the points of its loss in prior to the shuttle launch. It traces the movement of the fuel from the purchase to the on-board quantity and the loss that results in 54.6 of the purchased quantity being on board the Shuttle.

Separation of rate processes for isotopic exchange between hydrogen and liquid water in packed columns 10

International Nuclear Information System (INIS)

Butler, J.P.; Hartog, J. den; Goodale, J.W.; Rolston, J.H.

1977-01-01

Wetproofed platinum catalysts in packed columns promote isotopic exchange between counter-current streams of hydrogen saturated with water vapour and liquid water. The net rate of deuterium transfer from isotopically enriched hydrogen has been measured and separated into two rate processes involving the transfer of deuterium from hydrogen to water vapour and from water vapour to liquid. These are compared with independent measurements of the two rate processes to test the two-step successive exchange model for trickle bed reactors. The separated transfer rates are independent of bed height and characterize the deuterium concentrations of each stream along the length of the bed. The dependences of the transfer rates upon hydrogen and liquid flow, hydrogen pressure, platinum loading and the effect of dilution of the hydrophobic catalyst with inert hydrophilic packing are reported. The results indicate a third process may be important in the transfer of deuterium between hydrogen and liquid water. (author)

Forced convection of liquid hydrogen - Part 2 (continued) - case of large temperature differences between the fluid and the wall (rectangular channel); Convection forcee de l'hydrogene liquide - 2. partie (suite) - cas de grands ecarts de temperatures entre fluide et paroi (canal rectangulaire)

Energy Technology Data Exchange (ETDEWEB)

Perroud, P; Rebiere, J [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1965-07-01

Liquid hydrogen flows in a canal of rectangular cross section of 1 x 6 mm ; only one of the larger side is heated (length 190 mm) in order to simulate the cooling of a missile nozzle. The liquid is admitted subcooled at 25 deg. K in average and under a pressure of 8 bars. Mass velocity from 8.9 to 102 g/cm{sup 2}.s, heat flux from 18 to 296.6 W/cm{sup 2} and wall temperature reaching 800 deg. K. Two correlations of local heat transfer coefficients are presented, one for the region in two-phase flow and the other for the region in homogeneous gas-phase which are compared with the formula previously established for a cylindrical canal. An analysis of pressure drop is also given. Gross experimental results are separately published. (authors) [French] L'hydrogene liquide s'ecoule dans un canal de section rectangulaire de 1 x 6 mm, dont une seule grande face est chauffante (longueur: 190 mm), de facon a simuler le refroidissement d'une tuyere de fusee. Le liquide est admis sous-refroidi a 25 deg. K en moyenne et sous une pression de 8 bars. Vitesse massique de 8,9 a 102 g/cm{sup 2}.s, densite de flux de chaleur de 18 a 296,6 W/cm{sup 2} et temperature de paroi atteignant 800 deg. K. Deux correlations des coefficients d'echanges thermiques locaux sont presentees, l'une pour la region en double-phase et l'autre pour la region en phase gazeuse homogene que l'on compare avec les formules etablies precedemment pour le canal cylindrique. Une analyse des pertes de charge est egalement donnee. Les resultats experimentaux bruts sont publies separement. (auteurs)

Performance of a 10-kJ SMES model cooled by liquid hydrogen thermo-siphon flow for ASPCS study

International Nuclear Information System (INIS)

Makida, Y; Shintomi, T; Hamajima, T; Tsuda, M; Miyagi, D; Ota, N; Katsura, M; Ando, K; Takao, T; Tsujigami, H; Fujikawa, S; Hirose, J; Iwaki, K; Komagome, T

2015-01-01

We propose a new electrical power storage and stabilization system, called an Advanced Superconducting Power Conditioning System (ASPCS), which consists of superconducting magnetic energy storage (SMES) and hydrogen energy storage, converged on a liquid hydrogen station for fuel cell vehicles. A small 10- kJ SMES system, in which a BSCCO coil cooled by liquid hydrogen was installed, was developed to create an experimental model of an ASPCS. The SMES coil is conductively cooled by liquid hydrogen flow through a thermo-siphon line under a liquid hydrogen buffer tank. After fabrication of the system, cooldown tests were carried out using liquid hydrogen. The SMES coil was successfully charged up to a nominal current of 200 A. An eddy current loss, which was mainly induced in pure aluminum plates pasted onto each pancake coils for conduction cooling, was also measured. (paper)

DNB heat flux on inner side of a vertical pipe in forced flow of liquid hydrogen and liquid nitrogen

Science.gov (United States)

Shirai, Yasuyuki; Tatsumoto, Hideki; Shiotsu, Masahiro; Hata, Koichi; Kobayashi, Hiroaki; Naruo, Yoshihiro; Inatani, Yoshifumi

2018-06-01

Heat transfer from inner side of a heated vertical pipe to liquid hydrogen flowing upward was measured at the pressures of 0.4, 0.7 and 1.1 MPa for wide ranges of flow rate and liquid temperature. Nine test heaters with different inner diameters of 3, 4, 6 and 9 mm and the lengths of 50, 100, 150, 200, 250 and 300 mm were used. The DNB (departure from nucleate boiling) heat fluxes in forced flow of liquid hydrogen were measured for various subcoolings and flow velocities at pressures of 0.4, 0.7 and 1.1 MPa. Effect of L/d (ratio of heater length to diameter) was clarified for the range of L / d ⩽ 50 . A new correlation of DNB heat flux was presented based on a simple model and the experimental data. Similar experiments were performed for liquid nitrogen at pressures of 0.5 MPa and 1.0 MPa by using the same experimental system and some of the test heaters. It was confirmed that the new correlation can describe not only the hydrogen data, but also the data of liquid nitrogen.

Realization of a liquid hydrogen target

International Nuclear Information System (INIS)

Libin, J.F.; Gangnant, F.

1997-01-01

Experiments by the SPEG facility at GANIL need liquid hydrogen targets of some cm 3 . To achieve such targets, temperatures lower than 20 K must be obtained while their thin windows must withstand to pressures higher than 1000 m bars at these temperatures. Havar windows of 4.4 μm thickness met these requirements. A RW5 type Leybold cryo-generator was used as well as a system of ohmic heaters allowing regaining the initial state in a time equivalent with time elapsed for cooling. The working regime was chosen to be constant volume - variable pressure. The various components of this equipment (cryogenic head, buffer volume, hydrogen reservoir and vacuum pump) were coupled through 'aeroquip' allowing by dismantling and changes to keep the hydrogen isolated from the ambient atmosphere. The tests confirmed the accuracy of estimations done for the buffer volume and pressure. The only uncertainty is related to the window deformations. The time of cooling and reheating of target is around one hour. This allows during an experiment to aerate the chamber as the target was accessible to any necessary intervention

Liquid Transfer Cryogenic Test Facility: Initial hydrogen and nitrogen no-vent fill data

Science.gov (United States)

Moran, Matthew E.; Nyland, Ted W.; Papell, S. Stephen

1990-01-01

The Liquid Transfer Cryogenic Test Facility is a versatile testbed for ground-based cryogenic fluid storage, handling, and transfer experimentation. The test rig contains two well instrumented tanks, and a third interchangeable tank, designed to accommodate liquid nitrogen or liquid hydrogen testing. The internal tank volumes are approx. 18, 5, and 1.2 cu. ft. Tank pressures can be varied from 2 to 30 psia. Preliminary no vent fill tests with nitrogen and hydrogen were successfully completed with the test rig. Initial results indicate that no vent fills of nitrogen above 90 percent full are achievable using this test configuration, in a 1-g environment, and with inlet liquid temperatures as high as 143 R, and an average tank wall temperature of nearly 300 R. This inlet temperature corresponds to a saturation pressure of 19 psia for nitrogen. Hydrogen proved considerably more difficult to transfer between tanks without venting. The highest temperature conditions resulting in a fill level greater than 90 percent were with an inlet liquid temperature of 34 R, and an estimated tank wall temperature of slightly more than 100 R. Saturation pressure for hydrogen at this inlet temperature is 10 psia. All preliminary no vent fill tests were performed with a top mounted full cone nozzle for liquid injection. The nozzle produces a 120 degree conical droplet spray at a differential pressure of 10 psi. Pressure in the receiving tank was held to less than 30 psia for all tests.

Review of the methods to form hydrogen peroxide in electrical discharge plasma with liquid water

Science.gov (United States)

Locke, Bruce R.; Shih, Kai-Yuan

2011-06-01

This paper presents a review of the literature dealing with the formation of hydrogen peroxide from plasma processes. Energy yields for hydrogen peroxide generation by plasma from water span approximately three orders of magnitude from 4 × 10-2 to 80 g kWh-1. A wide range of plasma processes from rf to pulsed, ac, and dc discharges directly in the liquid phase have similar energy yields and may thus be limited by radical quenching processes at the plasma-liquid interface. Reactor modification using discharges in bubbles and discharges over the liquid phase can provide modest improvements in energy yield over direct discharge in the liquid, but the interpretation is complicated by additional chemical reactions of gas phase components such as ozone and nitrogen oxides. The highest efficiency plasma process utilizes liquid water droplets that may enhance efficiency by sequestering hydrogen peroxide in the liquid and by suppressing decomposition reactions by radicals from the gas and at the interface. Kinetic simulations of water vapor reported in the literature suggest that plasma generation of hydrogen peroxide should approach 45% of the thermodynamics limit, and this fact coupled with experimental studies demonstrating improvements with the presence of the condensed liquid phase suggest that further improvements in energy yield may be possible. Plasma generation of hydrogen peroxide directly from water compares favorably with a number of other methods including electron beam, ultrasound, electrochemical and photochemical methods, and other chemical processes.

Review of the methods to form hydrogen peroxide in electrical discharge plasma with liquid water

Energy Technology Data Exchange (ETDEWEB)

Locke, Bruce R; Shih, Kai-Yuan [Department of Chemical and Biomedical Engineering, Florida State University, Tallahassee, FL 32310 (United States)

2011-06-15

This paper presents a review of the literature dealing with the formation of hydrogen peroxide from plasma processes. Energy yields for hydrogen peroxide generation by plasma from water span approximately three orders of magnitude from 4 x 10{sup -2} to 80 g kWh{sup -1}. A wide range of plasma processes from rf to pulsed, ac, and dc discharges directly in the liquid phase have similar energy yields and may thus be limited by radical quenching processes at the plasma-liquid interface. Reactor modification using discharges in bubbles and discharges over the liquid phase can provide modest improvements in energy yield over direct discharge in the liquid, but the interpretation is complicated by additional chemical reactions of gas phase components such as ozone and nitrogen oxides. The highest efficiency plasma process utilizes liquid water droplets that may enhance efficiency by sequestering hydrogen peroxide in the liquid and by suppressing decomposition reactions by radicals from the gas and at the interface. Kinetic simulations of water vapor reported in the literature suggest that plasma generation of hydrogen peroxide should approach 45% of the thermodynamics limit, and this fact coupled with experimental studies demonstrating improvements with the presence of the condensed liquid phase suggest that further improvements in energy yield may be possible. Plasma generation of hydrogen peroxide directly from water compares favorably with a number of other methods including electron beam, ultrasound, electrochemical and photochemical methods, and other chemical processes.

Deuterium isotope separation factor between hydrogen and liquid water

International Nuclear Information System (INIS)

Rolston, J.H.; den Hartog, J.; Butler, J.P.

1976-01-01

The overall deuterium isotope separation factor between hydrogen and liquid water, α, has been measured directly for the first time between 280 and 370 0 K. The data are in good agreement with values of α calculated from literature data on the equilibrium constant for isotopic exchange between hydrogen and water vapor, K 1 , and the liquid-vapor separation factor, α/sub V/. The temperature dependence of α over the range 273-473 0 K based upon these new experimental results and existing literature data is given by the equation ln α = -0.2143 + (368.9/T) + (27,870/T 2 ). Measurements on α/sub V/ given in the literature have been surveyed and the results are summarized over the same temperature range by the equation ln α/sub V/ = 0.0592 - (80.3/T) +

A three-cell liquid hydrogen target for an extended focal plane polarimeter

International Nuclear Information System (INIS)

Golovanov, L.B.; Chesny, P.; Gheller, J.M.; Guillier, G.; Ladygin, V.P.; Theure, Ph.; Tomasi-Gustafsson, E.

1996-01-01

This article describes the design and working principle of a three-cell liquid hydrogen target produced for the high-energy deuteron polarimeter HYPOM. This target uses liquid helium as a cooling agent. After a general description of the apparatus, tests and operating modes are thoroughly explained. In particular the air controlled self-regulation of helium flow in the cryostat to stabilize the liquid hydrogen level is presented. The main feature of this target is the simplicity of the design as well as its safeness towards any incident. Results of cooling down, filling up of the target and stabilization regime were processed during one experiment of physics at synchrotron Saturne II. (orig.)

Neutronographic measurements of the motion of hydrogen and hydrogeneous substances in liquids and solids

International Nuclear Information System (INIS)

Zeilinger, A.; Pochman, W.A.; Rauch, H.; Suleiman, M.

1976-01-01

Earlier measurements of hydrogen motion in liquids by neutron radiography have been extended to obtain additional parameters of governing the mixing behavior of light and heavy water. Furthermore motion of water in concrete was measured leading to a determination of (1) the vapor diffusion coefficient of water in concrete, (2) the porosity of the concrete, and (3) the mass transfer coefficient of vapor from the concrete to the environment. Recently the ability of neutron radiography to measure the hydrogen motion in metals was demonstrated and the diffusion coefficients of hydrogen in V, Ta, Nb and beta-Ti was determined. In addition, some work on resolution measurements of neutron radiography will be reported. (author)

Build-up of a liquid hydrogen target with extremely thin windows

International Nuclear Information System (INIS)

Jaeckle, V.G.

1992-06-01

Small hydrogen targets with only a few cubic millimeters of liquid have many advantages in experiments on accelerators with phase-space cooled particle beams. In order to achieve good suppression of systematic errors by secondary reactions in the target and in the target windows, the thickness of the foil window for a 1 mm target may only be 0.3 μm. A pressure difference of 200 mbar permits the use of such thin foils (with a diameter of 6 mm). A purely mechanical pressure control unit was built, which consists of soft bellows and a loading weight. The pressure difference from a vacuum, which is in the bellows, is set by the weight on the bellows. The working parameters were chosen so that deuterium, nitrogen and oxygen can be used. The pressure variations in the cell are only ± 2.5 mbar. A mixing of gaseous and liquid hydrogen in the target cell and the formation of bubbles due to free convection can be prevented. A quiet volume of liquid hydrogen free of bubbles was obtained. (orig./HP) [de

Development of the ReaxFFCBN reactive force field for the improved design of liquid CBN hydrogen storage materials.

Science.gov (United States)

Pai, Sung Jin; Yeo, Byung Chul; Han, Sang Soo

2016-01-21

Liquid CBN (carbon-boron-nitrogen) hydrogen-storage materials such as 3-methyl-1,2-BN-cyclopentane have the advantage of being easily accessible for use in current liquid-fuel infrastructure. To develop practical liquid CBN hydrogen-storage materials, it is of great importance to understand the reaction pathways of hydrogenation/dehydrogenation in the liquid phase, which are difficult to discover by experimental methods. Herein, we developed a reactive force field (ReaxFFCBN) from quantum mechanical (QM) calculations based on density functional theory for the storage of hydrogen in BN-substituted cyclic hydrocarbon materials. The developed ReaxFFCBN provides similar dehydrogenation pathways and energetics to those predicted by QM calculations. Moreover, molecular dynamics (MD) simulations with the developed ReaxFFCBN can predict the stability and dehydrogenation behavior of various liquid CBN hydrogen-storage materials. Our simulations reveal that a unimolecular dehydrogenation mechanism is preferred in liquid CBN hydrogen-storage materials. However, as the temperature in the simulation increases, the contribution of a bimolecular dehydrogenation mechanism also increases. Moreover, our ReaxFF MD simulations show that in terms of thermal stability and dehydrogenation kinetics, liquid CBN materials with a hexagonal structure are more suitable materials than those with a pentagonal structure. We expect that the developed ReaxFFCBN could be a useful protocol in developing novel liquid CBN hydrogen-storage materials.

Solubilities of hydrogen and methane in coal liquids

Energy Technology Data Exchange (ETDEWEB)

Lin, Ho-mu; Sebastian, H M; Simnick, J J; Chao, Kwang Chu

1981-04-01

The solubilities of hydrogen and methane in Exxon Donor Solvent (EDS) and Solvent Refined Coal II (SRC-II) coal liquids are determined at 190 and 270 C and pressures to 250 atm. Two narrow boiling distillate cuts from EDS and three from SRC-II are studied.

A liquid hydrogen target for the calibration of the MEG and MEG II liquid xenon calorimeter

Energy Technology Data Exchange (ETDEWEB)

Signorelli, G., E-mail: giovanni.signorelli@pi.infn.it [INFN Sezione di Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Baldini, A.M. [INFN Sezione di Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Bemporad, C.; Cei, F.; Nicolò, D. [INFN Sezione di Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Università di Pisa, Dipartimento di Fisica, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Galli, L.; Gallucci, G.; Grassi, M. [INFN Sezione di Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Papa, A. [Paul Scherrer Institut, 5232 Villigen (Switzerland); Sergiampietri, F. [INFN Sezione di Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Venturini, M. [INFN Sezione di Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Scuola Normale Superiore, Piazza dei Cavalieri 7, 56126 Pisa (Italy)

2016-07-11

We designed, built and operated a liquid hydrogen target for the calibration of the liquid xenon calorimeter of the MEG experiment. The target was used throughout the entire data taking period, from 2008 to 2013 and it is being refurbished and partly re-designed to be integrated and used in the MEG-II experiment.

The TApIR experiment. IR absorption spectra of liquid hydrogen isotopologues

International Nuclear Information System (INIS)

Groessle, Robin

2015-01-01

The scope of the thesis is the infrared absorption spectroscopy of liquid hydrogen isotopologues with the tritium absorption infrared spectroscopy (TApIR) experiment at the tritium laboratory Karlsruhe (TLK). The calibration process from the sample preparation to the reference measurements are described. A further issue is the classical evaluation of FTIR absorption spectra and the extension using the rolling circle filter (RCF) including the effects on statistical and systematical errors. The impact of thermal and nuclear spin temperature on the IR absorption spectra is discussed. An empirical based modeling for the IR absorption spectra of liquid hydrogen isotopologues is performed.

Hydrogenation Reactions in Ionic Liquids. The Efficient Reduction of ...

African Journals Online (AJOL)

NJD

2008-12-09

Dec 9, 2008 ... Volatile organic solvents such as ethanol, methanol and THF are often used for the ... remained consistently high and only declined markedly on the fifth cycle. ... transferral of the viscous liquid from the hydrogenation reactor.

Final test results for the ground operations demonstration unit for liquid hydrogen

Science.gov (United States)

Notardonato, W. U.; Swanger, A. M.; Fesmire, J. E.; Jumper, K. M.; Johnson, W. L.; Tomsik, T. M.

2017-12-01

Described herein is a comprehensive project-a large-scale test of an integrated refrigeration and storage system called the Ground Operations and Demonstration Unit for Liquid Hydrogen (GODU LH2), sponsored by the Advanced Exploration Systems Program and constructed at Kennedy Space Center. A commercial cryogenic refrigerator interfaced with a 125,000 l liquid hydrogen tank and auxiliary systems in a manner that enabled control of the propellant state by extracting heat via a closed loop Brayton cycle refrigerator coupled to a novel internal heat exchanger. Three primary objectives were demonstrating zero-loss storage and transfer, gaseous liquefaction, and propellant densification. Testing was performed at three different liquid hydrogen fill-levels. Data were collected on tank pressure, internal tank temperature profiles, mass flow in and out of the system, and refrigeration system performance. All test objectives were successfully achieved during approximately two years of testing. A summary of the final results is presented in this paper.

Hydrogen storage by organic chemical hydrides and hydrogen supply to fuel cells with superheated liquid-film-type catalysis

International Nuclear Information System (INIS)

Hodoshima, S.; Shono, A.; Sato, K.; Saito, Y.

2004-01-01

Organic chemical hydrides, consisting of decalin / naphthalene and tetralin / naphthalene pairs, have been proposed as the storage medium of hydrogen for operating fuel cells in mobile and static modes. The target values in the DOE Hydrogen Plan, U.S., on storage ( 6.5 wt%, 62.0 kg-H 2 / m 3 ) are met with decalin ( 7.3 wt%, 64.8 kg-H 2 / m 3 ). In addition, existing gas stations and tank lorries are available for storage and supply of hydrogen by utilizing the decalin / naphthalene pair, suggesting that decalin is suitable for operating fuel-cell vehicles. Tetralin dehydrogenation proceeds quite rapidly, assuring a predominant power density, though its storage densities ( 3.0 wt%, 28.2 kg-H 2 / m 3 ) are relatively low. Efficient hydrogen supply from decalin or tetralin by heating at 210-280 o C was attained only with the carbon-supported nano-size metal catalysts in the 'superheated liquid-film states' under reactive distillation conditions, where coke formation over the catalyst surface was prevented. The catalyst layer superheated in the liquid-film states gave high reaction rates and conversions, minimizing the evaporation loss under boiling conditions and exergy loss in hydrogen energy systems. (author)

Long range order and hydrogen bonding in liquid methanol: A Monte Carlo simulation

Energy Technology Data Exchange (ETDEWEB)

Shilov, I.Y.; Rode, B.M. [Department of Theoretical Chemistry, Institute of General, Inorganic and Theoretical Chemistry, University of Innsbruck, Innrain 52a, A-6020 Innsbruck (Austria); Durov, V.A. [Department of Physical Chemistry, Faculty of Chemistry, Lomonosov Moscow State University, Moscow (Russian Federation)

1999-02-01

A Monte Carlo simulation of liquid methanol was performed in NVT ensemble at 298 K using a cubic simulation box containing 500 molecules. Long-range correlations in the liquid are discussed on the basis of site-site radial distribution functions. Hydrogen bonding and topological structure of the methanol aggregates were evaluated in detail, namely the number of linked molecules, formation of branches and cyclic structures. The necessity of larger simulation boxes for a full structural description and thermodynamic characterization of hydrogen-bonded liquids is clearly established by the results. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

Informing hazardous zones for on-board maritime hydrogen liquid and gas systems

Energy Technology Data Exchange (ETDEWEB)

Blaylock, Myra L. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Pratt, Joseph William [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Bran Anleu, Gabriela A. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Proctor, Camron [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2018-01-01

The significantly higher buoyancy of hydrogen compared to natural gas means that hazardous zones defined in the IGF code may be inaccurate if applied to hydrogen. This could place undue burden on ship design or could lead to situations that are unknowingly unsafe. We present dispersion analyses to examine three vessel case studies: (1) abnormal external vents of full blowdown of a liquid hydrogen tank due to a failed relief device in still air and with crosswind; (2) vents due to naturally-occurring boil-off of liquid within the tank; and (3) a leak from the pipes leading into the fuel cell room. The size of the hydrogen plumes resulting from a blowdown of the tank depend greatly on the wind conditions. It was also found that for normal operations releasing a small amount of "boil- off" gas to regulate the pressure in the tank does not create flammable concentrations.

Annihilation of antiprotons stopped in liquid hydrogen and deuterium

International Nuclear Information System (INIS)

Dalkarov, O.D.; Kerbikov, B.O.; Markushin, V.E.

1976-01-01

Detailed analysis is given of stopping antiproton annihilation in liquid hydrogen and deuterium. Connection between capture schedule and properties of bound states in nucleon-antinucleon system is established. The theoretical predictions are compared with experimental data which appeared in 1971-75

Interactions of solid and liquid lithium with steady state hydrogen and helium plasmas

International Nuclear Information System (INIS)

Hirooka, Y.; Nishikawa, M.; Ohgaki, H.; Ohtsuka, Y.

2005-01-01

A variety of innovative Plasma-Facing Component (PFC) concepts, employing moving solid or liquid surfaces, have recently been proposed in order to resolve technical issues, associated with the applications of currently used PFCs in future steady state fusion devices. As the first step to evaluate the concept using flowing-liquids for PFCs, steady state hydrogen and helium plasma interactions with solid and standing liquid lithium have been investigated in the present work, using the H α and He-I spectroscopy at the ion bombarding energies up to 150eV and at the lithium temperatures between room temperature and 480 deg C. Data indicate that hydrogen recycling over liquid lithium is clearly reduced, relative to that over solid lithium, whereas helium recycling does not show the same trend. From the kinetic analysis of these recycling time constant data, the activation energies for the overall recycling processes have been evaluated to be 0.02±0.01eV, both for hydrogen and helium plasmas. Also, it has been found that the activation energy is nearly independent of ion bombarding energy. (author)

KAJI EKSPERIMENTAL PENGGUNAAN LIQUID GAS FOR VEHICLE (LGV DENGAN PERTAMAX TERHADAP PERFORMA DAN EMISI GAS BUANG MOTOR BENSIN 2000 cc

Directory of Open Access Journals (Sweden)

Muhamad As’adi

2017-03-01

Full Text Available APBN 2015 mengisyaratkan bahwa Pemerintah akan mengurangi subsidi Bahan Bakar Minyak dari 48 juta kilo liter menjadi 46 juta kilo liter, implikasi dari hal ini jelas akan berdampak pada kebijakan penggunaan BBM dalam rangka untuk memenuhi kebutuhan sektor transportasi dan industri. Salah satu bahan bakar yang cadangannya masih cukup banyak dan pemanfaatannya masih terbatas pada kebutuhan rumah tangga serta usaha sector kuliner adalah Liquid Petrolium Gas (LPG. LPG mempunyai produk turunan dengan merk dagang Elpiji dan Liquid Gas for Vehicle (LGV atau sering disebut dengan Vigas. LGV mempunyai RON 98 setara dengan bahan bakar Pertamax dan mudah disimpan dalam tangki portabel karena tekanan nya relative rendah yaitu 8-15 bar, sedangakan tekanan bahan bakar Compressed Natural Gas (CNG yang sering disebut dengan Bahan Bakar Gas (BBG sekitar 200 bar. Perkembangan penggunaan LGV di masyarakat cenderung lambat hal ini disebabkan oleh keterbatasan infrastruktur yang ada dan pemahaman masyarakat tentang penggunaan LGV untuk sektor transportasi masih kurang. Tujuan dan target penelitian ini adalah didapatkannya konstanta performa dari motor bensin yang berbahan bakar LGV dan Pertamax, sehingga dapat memberikan pengetahuan kepada masyarakat bahwa LGV bisa digunakan sebagai bahan bakar pada sector transportasi dan lebih ekonomis. Metode yang digunakan dalam penelitian ini adalah metode eksprimen dengan mesin uji motor bensin 2000 cc yang berbahan bakar LGV dan Pertamax. Pengujian dilakukan dengan uji static diatas Dyno Test. Luaran data yang dihasilkan berupa performa mesin yang meliputi torsi, daya, konsumsi bahan bakar, selain uji static juga dilakukan uji emisi gas buang. Hasil pengujian menunjukkan bahwa enggunaan Liquid Gas For Vehicle (LGV dengan merk dagang Vigas mampu menaikkan Daya mesin maksimum sebesar 20,86% dan daya rata-rata sebesar 14,1%, torsi maksimum yang dihasilkan oleh Motor berbahan bakar Vigas lebih kecil dari motor yang berbahan bakar

Microcomputer-aided monitor for liquid hydrogen target system

International Nuclear Information System (INIS)

Kitami, T.; Watanabe, K.

1983-03-01

A microcomputer-aided monitor for a liquid hydrogen target system has been designed and tested. Various kinds of input data such as temperature, pressure, vacuum, etc. are scanned in a given time interval. Variation with time in any four items can be displayed on CRT and, if neccessary, printed out on a sheet of recording paper. (author)

Gas--liquid equilibria in mixtures of hydrogen and thianaphthene

Energy Technology Data Exchange (ETDEWEB)

Sebastian, H M; Simnick, J J; Lin, H M; Chao, K C

1978-12-01

Gas--liquid equilibrium conditions in binary mixtures of hydrogen and thianaphthene were experimentally determined at temperature of 190 to 430/sup 0/C and pressures to 250 atm in a flow apparatus. The same apparatus was also employed to measure the vapor pressure of thianaphthene. Comparisons of the new mixture data with Chao--Seader and Grayson--Streed correlations show that both correlations predict the thianaphthene equilibrium ratios well but are in error by up to about 45 and 35% respectively for K-values of hydrogen. 4 figures, 2 tables.

The self limiting effect of hydrogen cluster in gas jet under liquid nitrogen temperature

International Nuclear Information System (INIS)

Han Jifeng; Yang Chaowen; Miao Jingwei; Fu Pengtao; Luo Xiaobing; Shi Miangong

2010-01-01

The generation of hydrogen clusters in gas jet is tested using the Rayleigh scattering method under liquid nitrogen temperature of 79 K. The self limiting effect of hydrogen cluster is studied and it is found that the cluster formation is greatly affected by the number of expanded molecules. The well designed liquid nitrogen cold trap ensured that the hydrogen cluster would keep maximum size for maximum 15 ms during one gas jet. The scattered light intensity exhibits a power scaling on the backing pressure ranging from 5 to 48 bar with the power value of 4.1.

Simulation numérique du transfert de chaleur dans un moteur-fusée à propergol liquide

Directory of Open Access Journals (Sweden)

B. KHELIDJ

2015-03-01

Full Text Available Ce travail est une contribution à l'étude du refroidissement d'un moteur-fusée à propergol liquide. En effet pour protéger la paroi de la chambre propulsive, un système de refroidissement est nécessaire, car la température des gaz de combustion du propergol liquide dans la chambre de combustion, est très élevée. C'est pour montrer l'intérêt du refroidissement de la paroi de la chambre propulsive qu'une étude de simulation numérique, des phénomènes de combustion et de refroidissement dans la chambre propulsive, a été réalisée en régime permanent à l'aide du code de calcul Fluent. Les résultats de simulation, notamment ceux relatifs aux températures des parois le long de la chambre propulsive ont été confrontés à ceux trouvés dans la littérature.

Thermo-hydraulic test of the moderator cell of liquid hydrogen cold neutron source for the Budapest research reactor

International Nuclear Information System (INIS)

Grosz, Tamas; Rosta, Laszlo; Hargitai, Tibor; Mityukhlyaev, V.A.; Serebrov, A.P.; Zaharov, A.A.

1999-01-01

Thermo-hydraulic experiment was carried out in order to test performance of the direct cooled liquid hydrogen moderator cell to be installed at the research reactor of the Budapest Neutron Center. Two electric hearers up to 300 W each imitated the nuclear heat release in the liquid hydrogen as well as in construction material. The test moderator cell was also equipped with temperature gauges to measure the hydrogen temperature at different positions as well as the inlet and outlet temperature of cooling he gas. The hydrogen pressure in the connected buffer volume was also controlled. At 140 w expected total heat load the moderator cell was filled with liquid hydrogen within 4 hours. The heat load and hydrogen pressure characteristics of the moderator cell are also presented. (author)

Reactions of oxygen and hydrogen with liquid sodium - a critical survey

International Nuclear Information System (INIS)

Ullmann, H.

1982-01-01

The fundamentals of solvation chemistry are presented with appropriate components formulated. Methods of investigation and kinetics of the reactions are described. The hydrogen equilibrium pressure and saturation solubilities are described. The chemical equilibrium between O and H in solution is presented with detailed tabulation of the saturation solutions of oxygen, hydrogen and hydroxide in liquid sodium. Agreements and differences with the literature are presented

Solubility of Hydrogen and Nitrogen in liquid cast iron during melting and mold filling

OpenAIRE

Diószegi, Attila; Elfsberg, Jessica; Diószegi, Zoltán

2016-01-01

Defect formation like gas- and shrinkage porosity at cast iron component production is related to the content of gaseous elements in the liquid metal. The present work investigate the solubility of hydrogen and nitrogen in liquid iron aimed for production of lamellar and compacted graphite cast iron. The used methods and instruments are a combination of commercial measuring devices and novel experimental assemblies for measuring solubility of hydrogen and nitrogen during melting and mold fill...

ANALISIS OPINION SHOPPING, SIZE, LIQUIDITY, KUALITAS AUDIT TERHADAP OPINI AUDIT GOING CONCERN PADA PERUSAHAAN MANUFAKTUR SEKTOR TEKSTIL DAN GARMENT YANG TERDAFTAR DI BEI TAHUN 2010-2013

Directory of Open Access Journals (Sweden)

Kevin Martio

2014-03-01

Full Text Available Opini audit yang diberikan oleh auditor merupakan informasi penting bagi pengguna laporan keuangan Tujuan dari penelitian ini adalah untuk mendapatkan bukti empiris mengenai beberapa faktor yang dapat digunakan untuk memprediksi probabilitas opini audit going concern. Variable yang digunakan dalam penelitian ini adalah opinion shopping, size, liquidity, dan kualitas audit. Studi ini pada perusahaan manufaktur sektor tekstil dan garment yang listing di BEI periode 2010-2013. Metode pengambilan Sampel penelitian yang digunakan dalam penelitian ini adalah metode purposive sampling dengan 60 sampel yang telah mengalami pengamatan selama 4 tahun. Teknik analisis yang digunakan yaitu dengan regresi logistik. Penelitian ini membuktikan bahwa opinion shopping, size, dan liquidity berpengaruh negatif terhadap opini audit going concern dan dan kualitas audit berpengaruh positif terhadap opini audit going concern.

Corrosion behavior of construction materials for ionic liquid hydrogen compressor

DEFF Research Database (Denmark)

Arjomand Kermani, Nasrin; Petrushina, Irina; Nikiforov, Aleksey Valerievich

2016-01-01

The corrosion behavior of various commercially available stainless steels and nickel-based alloys as possible construction materials for components which are in direct contact with one of five different ionic liquids was evaluated. The ionic liquids, namely: 1-ethyl-3-methylimidazolium triflate, 1...... liquid hydrogen compressor. An electrochemical cell was specially designed, and steady-state cyclic voltammetry was used to measure the corrosion resistance of the alloys in the ionic liquids at 23 °C, under atmospheric pressure. The results showed a very high corrosion resistance and high stability...... for all the alloys tested. The two stainless steels, AISI 316L and AISI 347 showed higher corrosion resistance compared to AISI 321 in all the ionic liquids tested. It was observed that small addition of molybdenum, tantalum, and niobium to the alloys increased the corrosion stability in the ionic liquids...

Dynamic Compression Experiments on Hydrogen and Deuterium in the Warm Dense Liquid.

Science.gov (United States)

Desjarlais, Michael; McCoy, Chad; Cochrane, Kyle; Mattsson, Thomas; Knudson, Marcus; Redmer, Ronald

2017-06-01

Recently a shock-ramp platform has been developed on the Z Accelerator to access off-Hugoniot states in liquids. The accelerator delivers a two-step current pulse; the first accelerates the electrode to a constant velocity, which upon impact with the sample cell creates a well-defined shock, the subsequent current rise produces ramp compression from the initially shocked state producing relatively cool (1-2 kK), high pressure (>300 GPa), high compression (10 to 15-fold compression) states. This technique allows experimental access to the region of phase space where hydrogen is predicted to undergo a first-order phase transition from an insulating molecular-like to a conducting atomic-like liquid. Here we discuss the experimental platform, survey various theoretical predictions for the liquid-liquid, insulator-to-metal transition in hydrogen, and present results of experiments on both deuterium and hydrogen that clearly show an abrupt transition to a metallic state. We also present results from recent experiments at higher temperatures (3-4 kK) and compare the observations to both first-principles theory and previous step-wise loading experiments that exhibited a minimum metallic conductivity. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Data acquisition and quantitative analysis of stable hydrogen isotope in liquid and gas in the liquid phase catalytic exchange process

International Nuclear Information System (INIS)

Choi, H. J.; Lee, H. S.; Kim, K. R.; Cheong, H. S.; Ahn, D. H.; Lee, S. H.; Paek, S. W.; Kang, H. S.; Kim, J. G.

2001-01-01

A pilot plant for the Liquid Phase Catalytic Exchange process was built and has been operating to test the hydrophobic catalyst developed to remove the tritium generated at the CANDU nuclear power plants. The methods of quantitative analysis of hydrogen stable isotope were compared. Infrared spectroscopy was used for the liquid samples, and gas chromatography with hydrogen carrier gas showed the best result for gas samples. Also, a data acquisition system was developed to record the operation parameters. This record was very useful to investigate the causes of the system trip

Experimental Investigation of Jet-Induced Mixing of a Large Liquid Hydrogen Storage Tank

Science.gov (United States)

Lin, C. S.; Hasan, M. M.; Vandresar, N. T.

1994-01-01

Experiments have been conducted to investigate the effect of fluid mixing on the depressurization of a large liquid hydrogen storage tank. The test tank is approximately ellipsoidal, having a volume of 4.89 m(exp 3) and an average wall heat flux of 4.2 W/m(exp 2) due to external heat input. A mixer unit was installed near the bottom of the tank to generate an upward directed axial jet flow normal to the liquid-vapor interface. Mixing tests were initiated after achieving thermally stratified conditions in the tank either by the introduction of hydrogen gas into the tank or by self-pressurization due to ambient heat leak through the tank wall. The subcooled liquid jet directed towards the liquid-vapor interface by the mixer induced vapor condensation and caused a reduction in tank pressure. Tests were conducted at two jet submergence depths for jet Reynolds numbers from 80,000 to 495,000 and Richardson numbers from 0.014 to 0.52. Results show that the rate of tank pressure change is controlled by the competing effects of subcooled jet flow and the free convection boundary layer flow due to external tank wall heating. It is shown that existing correlations for mixing time and vapor condensation rate based on small scale tanks may not be applicable to large scale liquid hydrogen systems.

Liquid Acquisition Device Hydrogen Outflow Testing on the Cryogenic Propellant Storage and Transfer Engineering Design Unit

Science.gov (United States)

Zimmerli, Greg; Statham, Geoff; Garces, Rachel; Cartagena, Will

2015-01-01

As part of the NASA Cryogenic Propellant Storage and Transfer (CPST) Engineering Design Unit (EDU) testing with liquid hydrogen, screen-channel liquid acquisition devices (LADs) were tested during liquid hydrogen outflow from the EDU tank. A stainless steel screen mesh (325x2300 Dutch T will weave) was welded to a rectangular cross-section channel to form the basic LAD channel. Three LAD channels were tested, each having unique variations in the basic design. The LADs fed a common outflow sump at the aft end of the 151 cu. ft. volume aluminum tank, and included a curved section along the aft end and a straight section along the barrel section of the tank. Wet-dry sensors were mounted inside the LAD channels to detect when vapor was ingested into the LADs during outflow. The use of warm helium pressurant during liquid hydrogen outflow, supplied through a diffuser at the top of the tank, always led to early breakdown of the liquid column. When the tank was pressurized through an aft diffuser, resulting in cold helium in the ullage, LAD column hold-times as long as 60 minutes were achieved, which was the longest duration tested. The highest liquid column height at breakdown was 58 cm, which is 23 less than the isothermal bubble-point model value of 75 cm. This paper discusses details of the design, construction, operation and analysis of LAD test data from the CPST EDU liquid hydrogen test.

Mass spectrometric analysis of simple hydrogen compounds; Analyse de composes hydrogenes simples au spectrometre de masse

Energy Technology Data Exchange (ETDEWEB)

Nief, C; Botter, R [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

A uranium furnace is inserted in the gas inlet line of a mass spectrometer between the leak and the source. The line is fed with simple hydrogen compounds (H{sub 2}O, NH{sub 3}, H{sub 2}S) which are in this way reduced to hydrogen gas. Memory effects are largely avoided by heating the sample line to 90 deg. C. The speed of the isotopic analysis is only slightly less than that of hydrogen gas itself; the accuracy is better due to the reduction of fractionating effects in the leak. For the absolute measurements of deuterium in water, the presence of H{sub 3}{sup +} is a problem. Water samples, prepared by mixing an unknown light water sample with different amounts of heavy water, are equilibrated with hydrogen sulphide and analysis of the two phases of each sample enables the zero of the concentration scale to be determined from the point of intersection of the two curves obtained by plotting mixture composition against the observed isotope ratio in the two phases. The whole experiment can be carried out in the apparatus described which analyses hydrogen in H{sub 2}S and H{sub 2}O in the same way. (author) [French] Un four a uranium est insere dans la ligne d'introduction de gaz d'un spectrometre de masse entre la fuite et la source. La ligne est alimentee par des composes hydrogenes simples (H{sub 2}O, NH{sub 3}, H{sub 2}S) qui sont de cette facon transformes en hydrogene gazeux. On evite dans une large mesure les effets de memoire en chauffant la ligne de l'echantillon jusqu'a 90 deg. C. La vitesse de l'analyse isotopique est seulement legerement inferieure a celle de l'hydrogene gazeux lui-meme; la precision est meilleure du fait de la reduction des effets de fractionnement dans la fuite. Pour les mesures absolues du deuterium dans l'eau, la presence de H{sub 3}{sup +} pose un probleme. Les echantillons d'eau, prepares en melangeant un echantillon inconnu d'eau legere a differentes quantites d'eau lourde, sont equilibres par de l'hydrogene sulfure et l'analyse de

Design study of the cooling scheme for SMES system in ASPCS by using liquid hydrogen

Energy Technology Data Exchange (ETDEWEB)

Makida, Yasuhiro, E-mail: yasuhiro.makida@kek.jp [High Energy Accelerator Research Organization, Oho 1-1, Tsukuba 305-0801 (Japan); Shintomi, Takakazu [Nihon University, Chiyoda-ku, Tokyo 102-8251 (Japan); Asami, Takuya; Suzuki, Goro; Takao, Tomoaki [Sophia University, Chiyoda-ku, Tokyo 102-8554 (Japan); Hamajima, Takataro [Hachinohe Institutue of Technology, Hachinohe, Aomori 031-8501 (Japan); Tsuda, Makoto; Miyagi, Daisuke [Tohoku University, Aoba-ku, Sendai 980-8579 (Japan); Munakata, Kouhei; Kajiwara, Masataka [Iwatani Corp., Minato-ku, Tokyo 104-8058 (Japan)

2013-11-15

Highlights: •Advanced Superconducting Power Conditioning System is composed of SMES, FC–EL, H{sub 2} storage. •The ASPCS is proposed to be built beside a LH{sub 2} storage of a vehicle station to effectively use the cooling capability of liquid hydrogen. •The SMES coil, which is made from an MgB{sub 2} conductor, is indirectly cooled by LH{sub 2} through its own conduction. -- Abstract: From the point of view of environment and energy problems, the renewable energies have been attracting attention. However, fluctuating power generation by the renewable energies affects the stability of the power network. Thus, we propose a new electric power storage and stabilization system, Advanced Superconducting Power Conditioning System (ASPCS), in which a Superconducting Magnetic Energy Storage (SMES) and a hydrogen-energy-storage converge on a liquid hydrogen station for fuel cell vehicles. The ASPCS proposes that the SMES coils wound with MgB{sub 2} conductor are indirectly cooled by thermo-siphon circulation of liquid hydrogen to use its cooling capability. The conceptual design of cooling scheme of the ASPCS is presented.

Design study of the cooling scheme for SMES system in ASPCS by using liquid hydrogen

International Nuclear Information System (INIS)

Makida, Yasuhiro; Shintomi, Takakazu; Asami, Takuya; Suzuki, Goro; Takao, Tomoaki; Hamajima, Takataro; Tsuda, Makoto; Miyagi, Daisuke; Munakata, Kouhei; Kajiwara, Masataka

2013-01-01

Highlights: •Advanced Superconducting Power Conditioning System is composed of SMES, FC–EL, H 2 storage. •The ASPCS is proposed to be built beside a LH 2 storage of a vehicle station to effectively use the cooling capability of liquid hydrogen. •The SMES coil, which is made from an MgB 2 conductor, is indirectly cooled by LH 2 through its own conduction. -- Abstract: From the point of view of environment and energy problems, the renewable energies have been attracting attention. However, fluctuating power generation by the renewable energies affects the stability of the power network. Thus, we propose a new electric power storage and stabilization system, Advanced Superconducting Power Conditioning System (ASPCS), in which a Superconducting Magnetic Energy Storage (SMES) and a hydrogen-energy-storage converge on a liquid hydrogen station for fuel cell vehicles. The ASPCS proposes that the SMES coils wound with MgB 2 conductor are indirectly cooled by thermo-siphon circulation of liquid hydrogen to use its cooling capability. The conceptual design of cooling scheme of the ASPCS is presented

Reflector optimization for coupled liquid hydrogen moderator

International Nuclear Information System (INIS)

Kiyanagi, Y.; Iwasa, H.; Watanabe, N.; Furusaka, M.

1991-01-01

As a part of optimization studies on a coupled liquid hydrogen moderator system, the optimal thickness of the reflector, the effects of neutron absorbing liners and other beam hole/moderator on the cold-neutron-beam intensity were studied experimentally. It turns out that the optimal thickness is rather thick in this system and the existence of Cd liners around the beam extraction hole considerably reduces the cold neutron beam intensity, while the existence of other beam hole and moderator does not give an important intensity reduction. (author)

Liquid hydrogen production and commercial demand in the United States

Science.gov (United States)

Heydorn, Barbara

1990-01-01

Kennedy Space Center, the single largest purchaser of liquid hydrogen (LH2) in the United States, evaluated current and anticipated hydrogen production and consumption in the government and commercial sectors. Specific objectives of the study are as follows: (1) identify LH2 producers in the United States and Canada during 1980-1989 period; (2) compile information in expected changes in LH2 production capabilities over the 1990-2000 period; (3) describe how hydrogen is used in each consuming industry and estimate U.S. LH2 consumption for the chemicals, metals, electronics, fats and oil, and glass industries, and report data on a regional basis; (4) estimate historical and future consumption; and (5) assess the influence of international demands on U.S. plants.

Problems of hydrogen - water vapor - inert gas mixture use in heavy liquid metal coolant technology

International Nuclear Information System (INIS)

Ul'yanov, V.V.; Martynov, P.N.; Gulevskij, V.A.; Teplyakov, Yu.A.; Fomin, A.S.

2014-01-01

The reasons of slag deposit formation in circulation circuits with heavy liquid metal coolants, which can cause reactor core blockage, are considered. To prevent formation of deposits hydrogen purification of coolant and surfaces of circulation circuit is used. It consists in introduction of gaseous mixtures hydrogen - water vapor - rare gas (argon or helium) directly into coolant flow. The principle scheme of hydrogen purification and the processes occurring during it are under consideration. Measures which make it completely impossible to overlap of the flow cross section of reactor core, steam generators, pumps and other equipment by lead oxides in reactor facilities with heavy liquid metal coolants are listed [ru

Alkaline ionic liquids applied in supported ionic liquid catalyst for selective hydrogenation of citral to citronellal

Directory of Open Access Journals (Sweden)

Eero eSalminen

2014-02-01

Full Text Available The challenge in preparation of ionic liquids containing a strong alkaline anion is to identify a suitable cation which can tolerate the harsh conditions induced by the anion. In this study, a commercial quaternary ammonium compound (quat benzalkonium [ADBA] (alkyldimethylbenzylammonium was used as a cation in the synthesis of different alkaline ionic liquids. In fact, the precursor, benzalkonium chloride, is a mixture of alkyldimethylbenzylammonium chlorides of various alkyl chain lengths and is commonly used in the formulation of various antiseptic products. The prepared ionic liquids were utilized as Supported Ionic Liquid Catalysts (SILCAs. Typically, a SILCA contains metal nanoparticles, enzymes or metal complexes in an ionic liquid layer which is immobilized on a solid carrier material such as an active carbon cloth (ACC. The catalysts were applied in the selective hydrogenation of citral to citronellal which is an important perfumery chemical. Interestingly, 70 % molar yield towards citronellal was achieved over a catalyst containing the alkaline ionic liquid benzalkonium methoxide.

Alkaline ionic liquids applied in supported ionic liquid catalyst for selective hydrogenation of citral to citronellal

Science.gov (United States)

Salminen, Eero; Virtanen, Pasi; Mikkola, Jyri-Pekka

2014-01-01

The challenge in preparation of ionic liquids containing a strong alkaline anion is to identify a suitable cation which can tolerate the harsh conditions induced by the anion. In this study, a commercial quaternary ammonium compound (quat) benzalkonium [ADBA] (alkyldimethylbenzylammonium) was used as a cation in the synthesis of different alkaline ionic liquids. In fact, the precursor, benzalkonium chloride, is a mixture of alkyldimethylbenzylammonium chlorides of various alkyl chain lengths and is commonly used in the formulation of various antiseptic products. The prepared ionic liquids were utilized as Supported Ionic Liquid Catalysts (SILCAs). Typically, a SILCA contains metal nanoparticles, enzymes, or metal complexes in an ionic liquid layer which is immobilized on a solid carrier material such as an active carbon cloth (ACC). The catalysts were applied in the selective hydrogenation of citral to citronellal which is an important perfumery chemical. Interestingly, 70% molar yield toward citronellal was achieved over a catalyst containing the alkaline ionic liquid benzalkonium methoxide. PMID:24790972

Measurement of hydrogen solubility and desorption rate in V-4Cr-4Ti and liquid lithium-calcium alloys

Energy Technology Data Exchange (ETDEWEB)

Park, J.H.; Erck, R.; Park, E.T. [Argonne National Lab., IL (United States)] [and others

1997-04-01

Hydrogen solubility in V-4Cr-4Ti and liquid lithium-calcium was measured at a hydrogen pressure of 9.09 x 10{sup {minus}4} torr at temperatures between 250 and 700{degrees}C. Hydrogen solubility in V-4Cr-4Ti and liquid lithium decreased with temperature. The measured desorption rate of hydrogen in V-4Cr-4Ti is a thermally activated process; the activation energy is 0.067 eV. Oxygen-charged V-4Cr-4Ti specimens were also investigated to determine the effect of oxygen impurity on hydrogen solubility and desorption in the alloy. Oxygen in V-4Cr-4Ti increases hydrogen solubility and desorption kinetics. To determine the effect of a calcium oxide insulator coating on V-4Cr-4Ti, hydrogen solubility in lithium-calcium alloys that contained 0-8.0 percent calcium was also measured. The distribution ratio R of hydrogen between liquid lithium or lithium-calcium and V-4Cr-4Ti increased as temperature decreased (R {approx} 10 and 100 at 700 and 250{degrees}C, respectively). However at <267{degrees}C, solubility data could not be obtained by this method because of the slow kinetics of hydrogen permeation through the vanadium alloy.

Measurement of hydrogen solubility and desorption rate in V-4Cr-4Ti and liquid lithium-calcium alloys

International Nuclear Information System (INIS)

Park, J.H.; Erck, R.; Park, E.T.

1997-01-01

Hydrogen solubility in V-4Cr-4Ti and liquid lithium-calcium was measured at a hydrogen pressure of 9.09 x 10 -4 torr at temperatures between 250 and 700 degrees C. Hydrogen solubility in V-4Cr-4Ti and liquid lithium decreased with temperature. The measured desorption rate of hydrogen in V-4Cr-4Ti is a thermally activated process; the activation energy is 0.067 eV. Oxygen-charged V-4Cr-4Ti specimens were also investigated to determine the effect of oxygen impurity on hydrogen solubility and desorption in the alloy. Oxygen in V-4Cr-4Ti increases hydrogen solubility and desorption kinetics. To determine the effect of a calcium oxide insulator coating on V-4Cr-4Ti, hydrogen solubility in lithium-calcium alloys that contained 0-8.0 percent calcium was also measured. The distribution ratio R of hydrogen between liquid lithium or lithium-calcium and V-4Cr-4Ti increased as temperature decreased (R ∼ 10 and 100 at 700 and 250 degrees C, respectively). However at <267 degrees C, solubility data could not be obtained by this method because of the slow kinetics of hydrogen permeation through the vanadium alloy

A system of hydrogen powered vehicles with liquid organic hydrides

International Nuclear Information System (INIS)

Taube, M.

1981-07-01

A motor car system based on the hydrogen produced by nuclear power stations during the night in the summer, and coupled with organic liquid hydride seems to be a feasible system in the near future. Such a system is discussed and the cost is compared with gasoline. (Auth.)

Hydrogen gettering the overpressure gas from highly radioactive liquids

International Nuclear Information System (INIS)

Riley, D.L.; Schicker, J.R.

1996-04-01

Remediation of current inventories of high-activity radioactive liquid waste (HALW) requires transportation of Type-B quantities of radioactive material, possibly up to several hundred liters. However, the only currently certified packaging is limited to quantities of 50 ml (0.01 gal) quantities of Type-B radioactive liquid. Efforts are under way to recertify the existing packaging to allow the shipment of up to 4 L (1.1 gal) of Type-B quantities of HALW, but significantly larger packaging could be needed in the future. Scoping studies and preliminary designs have identified the feasibility of retrofitting an insert into existing casks, allowing the transport of up to 380 L (100 gal) of HALW. However, the insert design and ultimate certification strategy depend heavily on the gas-generating attributes of the HALW. A non-vented containment vessel filled with HALW, in the absence of any gas-mitigation technologies, poses a deflagration threat and, therefore, gas generation, specifically hydrogen generation, must be reliably controlled during all phases of transportation. Two techniques are available to mitigate hydrogen accumulation: recombiners and getters. Getters have an advantage over recombiners in that oxides are not required to react with the hydrogen. A test plan was developed to evaluate three forms of getter material in the presence of both simulated HALW and the gases that are produced by the HALW. These tests demonstrated that getters can react with hydrogen in the presence of simulated waste and in the presence of several other gases generated by the HALW, such as nitrogen, ammonia, nitrous oxide, and carbon monoxide. Although the use of such a gettering system has been shown to be technically feasible, only a preliminary design for its use has been completed. No further development is planned until the requirement for bulk transport of Type-B quantities of HALW is more thoroughly defined

Liquid-Hydrogen-Cooled 450-hp Electric Motor Test Stand Being Developed

Science.gov (United States)

Kascak, Albert F.; Trudell, Jeffrey J.; Brown, Gerald V.

2005-01-01

With growing concerns about global warming, there is a need to develop pollution-free aircraft. One approach is to use hydrogen-fueled aircraft that use fuel cells or turbogenerators to produce electric power to drive the electric motors that turn the aircraft s propulsive fans. Hydrogen fuel would be carried as a liquid, stored at its boiling point of 20.5 K (-422.5 F). Conventional electric motors, however, are too heavy for aircraft propulsion. We need to develop high-power, lightweight electric motors (highpower- density motors). One approach is to increase the conductivity of the wires by cooling them with liquid hydrogen (LH2). This would allow superconducting rotors with an ironless core. In addition, the motor could use very pure aluminum or copper, substances that have low resistances at cryogenic temperatures. A preliminary design of a 450-hp LH2-cooled electric motor was completed and is being manufactured by a contractor. This motor will be tested at the NASA Glenn Research Center and will be used to test different superconducting materials such as magnesium diboride (MgB2). The motor will be able to operate at speeds of up to 6000 rpm.

Silicon surface barrier detectors used for liquid hydrogen density measurement

Science.gov (United States)

James, D. T.; Milam, J. K.; Winslett, H. B.

1968-01-01

Multichannel system employing a radioisotope radiation source, strontium-90, radiation detector, and a silicon surface barrier detector, measures the local density of liquid hydrogen at various levels in a storage tank. The instrument contains electronic equipment for collecting the density information, and a data handling system for processing this information.

Design and prototyping of an ionic liquid piston compressor as a new generation of compressors for hydrogen refueling stations

DEFF Research Database (Denmark)

Arjomand Kermani, Nasrin

to investigate the heat transfer phenomena inside the compression chamber; the system performance is evaluated, followed by the design process. The model is developed based on the mass and energy balance of the hydrogen, and liquid bounded by the wall of the compression chamber. Therefore, at each time step...... and positional node, the model estimates the pressure and temperature of the hydrogen and liquid, the temperature of the compression chamber wall, and the amount of heat extracted from the hydrogen directly at the interface between the hydrogen and liquid, and through the wall. The results indicate......, fabrication, and control of the prototype is described in the presented work. The new compressor design has high potential to be used as an alternative to the conventional reciprocating compressors in hydrogen refueling stations, as it provides a simpler design with lower manufacturing costs, higher...

Heat transfer in pool boiling liquid neon, deuterium and hydrogen, and critical heat flux in forced convection of liquid neon

International Nuclear Information System (INIS)

Astruc, J.M.

1967-12-01

In the first part, free-convection and nucleate pool boiling heat transfer (up to burn-out heat flux) between a platinum wire of 0.15 mm in diameter in neon, deuterium and hydrogen has been studied at atmospheric pressure. These measurements were continued in liquid neon up to 23 bars (Pc ≅ 26.8 b). Film boiling heat transfer coefficients have been measured in pool boiling liquid neon at atmospheric pressure with three heating wires (diameters 0.2, 0.5, 2 mm). All the results have been compared with existing correlations. The second part is devoted to measurements of the critical heat flux limiting heat transfer with small temperature differences between the wall and the liquid neon flowing inside a tube (diameters 3 x 3.5 mm) heated by joule effect on 30 cm of length. Influences of flow stability, nature of electrical current, pressure, mass flow rate and subcooling are shown. In conclusion, the similarity of the heat transfer characteristics in pool boiling as well as in forced convection of liquid neon and hydrogen is emphasized. (author) [fr

Current Design of the Flange Type Hydrogen Permeation Sensor in Liquid Breeder

International Nuclear Information System (INIS)

Lee, E. H.; Jin, H. G.; Yoon, J. S.; Kim, S. K.; Lee, D. W.; Lee, H. G.

2015-01-01

In 2004, A. Ciampichetti et al. proposed a hollow capsule shape permeation sensor and they theoretically and experimentally evaluated the performance of the sensor made of Nb membrane at test condition of 500 .deg. C. However, the evaluation result showed the measured hydrogen permeation flux in the sensor much lower than the predicted one and they concluded that, the result is due to the formation of an oxide layer on the sensor membrane surface. Three years later, A. Ciampichetti et al. observed that a hollow capsule shape permeation sensor has too long response time to measure hydrogen concentration in liquid breeder. However, they suggested optimizing the sensor geometry with the reduction of the ratio 'total sensor volume/permeation surface' to overcome the low hydrogen permeating flux. For development of the liquid breeding technologies in nuclear fusion, the permeation sensor to measure tritium concentration in liquid metal breeder has been developed. Lee et al. proposed a flange type permeation sensor to dramatically reduce the ratio sensor 'inside volume/permeation surface' and to remove membrane welding during sensor manufacture process. However, the flange type sensor has problem with sealing. In present study, the modified flange sensor design with a metallic C-ring spring gasket is introduced. The modified sensor will be verified and evaluated under high temperature conditions by end of 2015

Current Design of the Flange Type Hydrogen Permeation Sensor in Liquid Breeder

Energy Technology Data Exchange (ETDEWEB)

Lee, E. H.; Jin, H. G.; Yoon, J. S.; Kim, S. K.; Lee, D. W. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, H. G. [National Fusion Research Institute, Daejeon (Korea, Republic of)

2015-10-15

In 2004, A. Ciampichetti et al. proposed a hollow capsule shape permeation sensor and they theoretically and experimentally evaluated the performance of the sensor made of Nb membrane at test condition of 500 .deg. C. However, the evaluation result showed the measured hydrogen permeation flux in the sensor much lower than the predicted one and they concluded that, the result is due to the formation of an oxide layer on the sensor membrane surface. Three years later, A. Ciampichetti et al. observed that a hollow capsule shape permeation sensor has too long response time to measure hydrogen concentration in liquid breeder. However, they suggested optimizing the sensor geometry with the reduction of the ratio 'total sensor volume/permeation surface' to overcome the low hydrogen permeating flux. For development of the liquid breeding technologies in nuclear fusion, the permeation sensor to measure tritium concentration in liquid metal breeder has been developed. Lee et al. proposed a flange type permeation sensor to dramatically reduce the ratio sensor 'inside volume/permeation surface' and to remove membrane welding during sensor manufacture process. However, the flange type sensor has problem with sealing. In present study, the modified flange sensor design with a metallic C-ring spring gasket is introduced. The modified sensor will be verified and evaluated under high temperature conditions by end of 2015.

Method and apparatus for electrokinetic co-generation of hydrogen and electric power from liquid water microjets

Energy Technology Data Exchange (ETDEWEB)

Saykally, Richard J; Duffin, Andrew M; Wilson, Kevin R; Rude, Bruce S

2013-02-12

A method and apparatus for producing both a gas and electrical power from a flowing liquid, the method comprising: a) providing a source liquid containing ions that when neutralized form a gas; b) providing a velocity to the source liquid relative to a solid material to form a charged liquid microjet, which subsequently breaks up into a droplet spay, the solid material forming a liquid-solid interface; and c) supplying electrons to the charged liquid by contacting a spray stream of the charged liquid with an electron source. In one embodiment, where the liquid is water, hydrogen gas is formed and a streaming current is generated. The apparatus comprises a source of pressurized liquid, a microjet nozzle, a conduit for delivering said liquid to said microjet nozzle, and a conductive metal target sufficiently spaced from said nozzle such that the jet stream produced by said microjet is discontinuous at said target. In one arrangement, with the metal nozzle and target electrically connected to ground, both hydrogen gas and a streaming current are generated at the target as it is impinged by the streaming, liquid spray microjet.

40 CFR Table 3 to Subpart IIIii of... - Work Practice Standards-Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen...

Science.gov (United States)

2010-07-01

... Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks 3 Table 3 to... Standards—Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks... cell back into service until the leaking equipment is repaired. 3. A decomposer or hydrogen system...

Liquid alternative diesel fuels with high hydrogen content

Energy Technology Data Exchange (ETDEWEB)

Hancsok, Jenoe; Varga, Zoltan; Eller, Zoltan; Poelczmann, Gyoergy [Pannonia Univ., Veszprem (Hungary). MOL Dept. of Hydrocarbon Processing; Kasza, Tamas [MOL Hungarian Oil and Gas Plc., Szazhalombatta (Hungary)

2013-06-01

Mobility is a keystone of the sustainable development. In the operation of the vehicles as the tools of mobility internal combustion engines, so thus Diesel engines will play a remarkable role in the next decades. Beside fossil fuels - used for power these engines - liquid alternative fuels have higher and higher importance, because of their known advantages. During the presentation the categorization possibilities based on the chronology of their development and application will be presented. The importance of fuels with high hydrogen content will be reviewed. Research and development activity in the field of such kind of fuels will be presented. During this developed catalytic systems and main performance properties of the product will be presented which were obtained in case of biogasoils produced by special hydrocracking of natural triglycerides and in case of necessity followed by isomerization; furthermore in case of synthetic biogasoils obtained by the isomerization hydrocracking of Fischer-Tropsch paraffins produced from biomass based synthesis gas. Excellent combustion properties (cetane number > 65-75), good cold flow properties and reduced harmful material emission due to the high hydrogen content (C{sub n}H{sub 2n+2}) are highlighted. Finally production possibilities of linear and branched paraffins based on lignocelluloses are briefly reviewed. Summarizing it was concluded that liquid hydrocarbons with high isoparaffin content are the most suitable fuels regarding availability, economical and environmental aspects, namely the sustainable development. (orig.)

Heat transfer analysis of liquid piston compressor for hydrogen applications

DEFF Research Database (Denmark)

Kermani, Nasrin Arjomand; Rokni, Masoud

2015-01-01

A hydrogen compression technology using liquid as the compression piston is investigated from heat transfer point of view. A thermodynamic model, simulating a single compression stroke, is developed to investigate the heat transfer phenomena inside the compression chamber. The model is developed...... and through the walls, is investigated and compared with the adiabatic case. The results show that depending on heat transfer correlation, the hydrogen temperature reduces slightly between 0.2% and 0.4% compared to the adiabatic case, at 500bar, due to the large wall resistance and small contact area...... at the interface. Moreover, the results of the sensitivity analysis illustrates that increasing the total heat transfer coefficients at the interface and the wall, together with compression time, play key roles in reducing the hydrogen temperature. Increasing the total heat transfer coefficient at the interface...

Isolasi dan Karakterisasi Ralstonia syzygii

Directory of Open Access Journals (Sweden)

Yanuar Danaatmadja

2009-07-01

Full Text Available Ralstonia syzygii is one of important pathogens of cloves. This study was aimed at obtaining pure culture of R. syzygi from diseased plant tissue samples. The acterium was isolated from infected clove plantations in Ungaran, Central Java. It had the ability to make clove seedlings show symptoms and then die 41 days after inoculation. The reisolated bacterium also showed its ability to kill clove seedlings after 17 days. The bacterium is gram negative, able to ultilize glucose, sucrose, maltose, mannitol, sorbitol, dulcitol, and glycerol, able to hydrolyze starch, grow well at 27oC, able to catalyze and release water and oxygen from hydrogen peroxyde (H2O2 and aerobically.   Ralstonia syzygii merupakan salah satu patogen penting pada tanaman cengkeh. Penelitian ini dilakukan untuk mendapakan isolat murni R syzygii dari jaringan tanaman terinfeksi. Bakteri diisolasi dari pertanaman cengkeh sakit yang berasal dari daerah Ungaran, Jawa Tengah. Bakteri menunjukkan kemampuan untuk menyebabkan bibit tanaman cangkeh sakit dan kemudian mati 41 hsi. Bakteri hasil reisolasi juga menunjukkan kemampuannya menyebabkan sakit dan kematian pada bibit tanaman cengkeh setelah 17 hsi. Bakteri yang diperoleh bersifat gram negatif, mampu memanfaatkan glukosa, sukrosa, maltosa, manitol, sorbitol, dulsitol, dan gliserol, mampu menghidrolisis pati, tumbuh baik pada suhu 27o C, mampu mengkatalisis dan melepaskan air dan oksigen dari hydrogen peroxide (H2O2 dan bersifat aerob.

Comparison of the renewable transportation fuels, liquid hydrogen and methanol, with gasoline - energetic and economic aspects

International Nuclear Information System (INIS)

Specht, M.; Staiss, F.; Bandi, A.; Weimer, T.

1998-01-01

In this paper, the renewable energy vectors liquid hydrogen (LH 2 ) and methanol generated from atmospheric CO 2 are compared with the conventional crude oil-gasoline system. Both renewable concepts, liquid hydrogen and methanol, lead to a drastic CO 2 reduction compared to the fossil-based system. The comparison between the LH 2 and methanol vector for the transport sector shows nearly the same fuel cost and energy efficiency but strong infrastructure advantages for methanol. (author)

Research on Liquid Management Technology in Water Tank and Reactor for Propulsion System with Hydrogen Production System Utilizing Aluminum and Water Reaction

Science.gov (United States)

Imai, Ryoji; Imamura, Takuya; Sugioka, Masatoshi; Higashino, Kazuyuki

2017-12-01

High pressure hydrogen produced by aluminum and water reaction is considered to be applied to space propulsion system. Water tank and hydrogen production reactor in this propulsion system require gas and liquid separation function under microgravity condition. We consider to install vane type liquid acquisition device (LAD) utilizing surface tension in the water tank, and install gas-liquid separation mechanism by centrifugal force which swirling flow creates in the hydrogen reactor. In water tank, hydrophilic coating was covered on both tank wall and vane surface to improve wettability. Function of LAD in water tank and gas-liquid separation in reaction vessel were evaluated by short duration microgravity experiments using drop tower facility. In the water tank, it was confirmed that liquid was driven and acquired on the outlet due to capillary force created by vanes. In addition of this, it was found that gas-liquid separation worked well by swirling flow in hydrogen production reactor. However, collection of hydrogen gas bubble was sometimes suppressed by aluminum alloy particles, which is open problem to be solved.

Efek Pemordanan terhadap Pewarnaan Menggunakan Kombinasi Limbah Cair Gambir dan Ekstrak Kayu Secang pada Kain Rayon dan Katun

Directory of Open Access Journals (Sweden)

F Failisnur

2017-12-01

Full Text Available Combination of gambier liquid waste and secang wood (Caesalpinea sappan L. can add color variations of fabric dyed with natural dyes. This research explained the effect of dyeing combination of gambir liquid waste and secang wood with different mordant method and type on the color shade and other characteristics of rayon and cotton dyed fabric. The mordant process was performed as much as 1 and 2 times using CaO, Al(2SO43, FeSO4 mordant and then compared without mordant treatment. The result of the dyed fabrics was evaluated the color shade, color strength (K/S, and fastness properties. The results showed that the color shade of rayon and cotton fabrics were varied. Rayon fibers had a greater affinity and absorption to the liquids waste of gambier and secang wood than in cellulose fibers. The mordant process could increase color strength (K/S and color fastness to washing, acidic perspiration, rubbing, and light.ABSTRAKKombinasi limbah cair gambir dan kayu secang (Caesalpinea sappan L. dapat menambah variasi warna kain yang dicelup dengan pewarna alami. Penelitian ini menjelaskan tentang efek pewarnaan kombinasi limbah cair gambir dan kayu secang dengan metoda dan  jenis mordan yang berbeda terhadap arah warna dan karakteristik lainnnya dari kain rayon dan katun hasil celupan. Proses mordan yang digunakan adalah 1 kali dan 2 kali mordan menggunakan CaO, Al(2SO43, FeSO4 yang dibandingkan dengan tanpa mordan. Kain hasil pewarnaan dievaluasi arah warna, intensitas warna (K/S, dan ketahanan luntur warna. Hasil penelitian menunjukkan arah warna kain rayon dan katun yang lebih bervariasi. Serat rayon memiliki afinitas dan penyerapan yang lebih besar terhadap zat warna limbah cair gambir dan kayu secang dibandingkan dengan serat selulosa.  Proses mordan dapat meningkatkan intensitas warna (K/S dan ketahanan luntur warna terhadap pencucian, keringat asam, gosokan, dan sinar.

Simulation on a proposed large-scale liquid hydrogen plant using a multi-component refrigerant refrigeration system

Energy Technology Data Exchange (ETDEWEB)

Krasae-in, Songwut [Norwegian University of Science and Technology, Kolbjorn Hejes vei 1d, NO-7491 Trondheim (Norway); Stang, Jacob H.; Neksa, Petter [SINTEF Energy Research AS, Kolbjorn Hejes vei 1d, NO-7465 Trondheim (Norway)

2010-11-15

A proposed liquid hydrogen plant using a multi-component refrigerant (MR) refrigeration system is explained in this paper. A cycle that is capable of producing 100 tons of liquid hydrogen per day is simulated. The MR system can be used to cool feed normal hydrogen gas from 25 C to the equilibrium temperature of -193 C with a high efficiency. In addition, for the transition from the equilibrium temperature of the hydrogen gas from -193 C to -253 C, the new proposed four H{sub 2} Joule-Brayton cascade refrigeration system is recommended. The overall power consumption of the proposed plant is 5.35 kWh/kg{sub LH2}, with an ideal minimum of 2.89 kWh/kg{sub LH2}. The current plant in Ingolstadt is used as a reference, which has an energy consumption of 13.58 kWh/kg{sub LH2} and an efficiency of 21.28%: the efficiency of the proposed system is 54.02% or more, where this depends on the assumed efficiency values for the compressors and expanders. Moreover, the proposed system has some smaller-size heat exchangers, much smaller compressor motors, and smaller crankcase compressors. Thus, it could represent a plant with the lowest construction cost with respect to the amount of liquid hydrogen produced in comparison to today's plants, e.g., in Ingolstadt and Leuna. Therefore, the proposed system has many improvements that serve as an example for future hydrogen liquefaction plants. (author)

A heat exchanger between forced flow helium gas at 14 to 18 K and liquid hydrogen at 20 K circulated by natural convection

International Nuclear Information System (INIS)

Green, M.A.; Ishimoto, S.; Lau, W.; Yang, S.

2003-01-01

The Muon Ionization Cooling Experiment (MICE) has three 350-mm long liquid hydrogen absorbers to reduce the momentum of 200 MeV muons in all directions. The muons are then re-accelerated in the longitudinal direction by 200 MHz RF cavities. The result is cooled muons with a reduced emittance. The energy from the muons is taken up by the liquid hydrogen in the absorber. The hydrogen in the MICE absorbers is cooled by natural convection to the walls of the absorber that are in turn cooled by helium gas that enters at 14 K. This report describes the MICE liquid hydrogen absorber and the heat exchanger between the liquid hydrogen and the helium gas that flows through passages in the absorber wall

Organic chemical hydrides as storage medium of hydrogen on the basis of superheated liquid-film concept

International Nuclear Information System (INIS)

Shinya Hodoshima; Atsushi Shono; Kazumi Satoh; Yasukazu Saito

2006-01-01

A catalysis pair of tetralin dehydrogenation / naphthalene hydrogenation has been proposed in the present paper as an organic chemical hydride for operating stationary fuel cells. Catalytic naphthalene hydrogenation, having been commercialized since the 1940's, proceeds to generate decalin via tetralin as an intermediate. The storage capacities of tetralin (3.0 wt%, 28.2 kg-H 2 / m 3 ) are lower than decalin (7.3 wt%, 64.8 kg-H 2 / m 3 ) but both tetralin dehydrogenation and naphthalene hydrogenation are much faster than the decalin / naphthalene pair. Moreover, existing infrastructures, e.g., gas station and tank lorry, are available for storage, transportation and supply of hydrogen. As for the stationary fuel cells with large space for hydrogen storage, tetralin as a hydrogen carrier is superior to decalin in terms of fast hydrogen supply. Rapid hydrogen supply from tetralin under mild conditions was only accomplished with the carbon supported metal catalysts in the 'superheated liquid-film states' under reactive distillation conditions. In contrast to the ordinary suspended states, the catalyst layer superheated in the liquid-film state gave high catalytic performances at around 250 C. As a result, serious coke formation over the catalyst surface and excessive exergy consumption were prevented simultaneously. (authors)

Forced convection of liquid hydrogen. 1. part - the case of a low temperature difference between the liquid and the wall; Convection forcee de l'hydrogene liquide - 1. partie - cas de faibles ecarts de temperatures entre fluide et paroi

Energy Technology Data Exchange (ETDEWEB)

Perroud, P; Rebiere, J [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1964-07-01

Measurements have been performed in a smooth Inconel tube of 3 mm ID, 3.5 mm OD, electrically heated (DC) along 300 mm of its length. The liquid enters the test section subcooled at a constant temperature of 20.3 deg. K. Pressure varied from 2 to 16 atm, mass velocity from 5 to 35 g/cm{sup 2}.s giving Reynolds numbers from 20000 to 100000. A formula of correlation for the heat transfer coefficients is given for the homogenous liquid phase. Burn-out phenomenon is seriously affected by flow oscillations. Effect of mass velocity and pressure on burn-out heat fluxes is discussed. Pressure drops can be calculated by considering the variation of momentum in a one-dimensional model. Head losses due to friction are negligible. (authors) [French] Les mesures ont ete effectuees dans les conditions suivantes: tube lisse en inconel de 3 x 3,5 mm de diametre, chauffe sur une longueur de 300 mm par effet Joule. Le liquide entre sous-refroidi, a une temperature constante de 20,3 deg. K. La pression a varie de 2 a 16 atm, le debit en masse par unite de section droite du tube de 5 a 35 g/cm{sup 2}.s, ce qui correspond a des nombres de Reynolds de 20000 a 100000. On donne une formule de correlation des coefficients d'echanges en phase liquide homogene. Le phenomene de burnout est gravement affecte par les oscillations de debit. On discute l'influence du debit et de la pression sur les valeurs du flux de burnout. On peut calculer la chute de pression par la variation de la quantite de mouvement dans un modele unidimensionnel. Les pertes de charge par frottement sont negligeables. (auteurs)

The effect of a micro bubble dispersed gas phase on hydrogen isotope transport in liquid metals under nuclear irradiation

Energy Technology Data Exchange (ETDEWEB)

Fradera, J., E-mail: jfradera@ubu.es; Cuesta-López, S., E-mail: scuesta@ubu.es

2013-12-15

The present work intend to be a first step towards the understanding and quantification of the hydrogen isotope complex phenomena in liquid metals for nuclear technology. Liquid metals under nuclear irradiation in, e.g., breeding blankets of a nuclear fusion reactor would generate tritium which is to be extracted and recirculated as fuel. At the same time that tritium is bred, helium is also generated and may precipitate in the form of nano bubbles. Other liquid metal systems of a nuclear reactor involve hydrogen isotope absorption processes, e.g., tritium extraction system. Hence, hydrogen isotope absorption into gas bubbles modelling and control may have a capital importance regarding design, operation and safety. Here general models for hydrogen isotopes transport in liquid metal and absorption into gas phase, that do not depend on the mass transfer limiting regime, are exposed and implemented in OpenFOAM® CFD tool for 0D–3D simulations. Results for a 0D case show the impact of a He dispersed phase of nano bubbles on hydrogen isotopes inventory at different temperatures as well as the inventory evolution during a He nucleation event. In addition, 1D and 2D axisymmetric cases are exposed showing the effect of a He dispersed gas phase on hydrogen isotope permeation through a lithium lead eutectic alloy and the effect of vortical structures on hydrogen isotope transport at a backward facing step. Exposed results give a valuable insight on current nuclear technology regarding the importance of controlling hydrogen isotope transport and its interactions with nucleation event through gas absorption processes.

C1 Chemistry for the Production of Ultra-Clean Liquid Transportation Fuels and Hydrogen

Energy Technology Data Exchange (ETDEWEB)

Gerald P. Huffman

2006-03-30

Professors and graduate students from five universities--the University of Kentucky, University of Pittsburgh, University of Utah, West Virginia University, and Auburn University--are collaborating in a research program to develop C1 chemistry processes to produce ultra-clean liquid transportation fuels and hydrogen, the zero-emissions transportation fuel of the future. The feedstocks contain one carbon atom per molecular unit. They include synthesis gas (syngas), a mixture of carbon monoxide and hydrogen produced by coal gasification or reforming of natural gas, methane, methanol, carbon dioxide, and carbon monoxide. An important objective is to develop C1 technology for the production of liquid transportation fuel and hydrogen from domestically plentiful resources such as coal, coalbed methane, and hydrocarbon gases and liquids produced from coal. An Advisory Board with representatives from Chevron-Texaco, Eastman Chemical, Conoco-Phillips, the Air Force Research Laboratory, the U.S. Army National Automotive Center, and Tier Associates provides guidance on the practicality of the research. The current report summarizes the results obtained in this program during the period October 1, 2002 through March 31, 2006. The results are presented in detailed reports on 16 research projects headed by professors at each of the five CFFS Universities and an Executive Summary. Some of the highlights from these results are: (1) Small ({approx}1%) additions of acetylene or other alkynes to the Fischer-Tropsch (F-T) reaction increases its yield, causes chain initiation, and promotes oxygenate formation. (2) The addition of Mo to Fe-Cu-K/AC F-T catalysts improves catalyst lifetime and activity. (3) The use of gas phase deposition to place highly dispersed metal catalysts on silica or ceria aerogels offers promise for both the F-T and the water-gas shift WGS reactions. (4) Improved activity and selectivity are exhibited by Co F-T catalysts in supercritical hexane. (5) Binary Fe

Modeling the Thermal Mechanical Behavior of a 300 K Vacuum Vessel that is Cooled by Liquid Hydrogen in Film Boiling

International Nuclear Information System (INIS)

Yang, S.Q.; Green, M.A.; Lau, W.

2004-01-01

This report discusses the results from the rupture of a thin window that is part of a 20-liter liquid hydrogen vessel. This rupture will spill liquid hydrogen onto the walls and bottom of a 300 K cylindrical vacuum vessel. The spilled hydrogen goes into film boiling, which removes the thermal energy from the vacuum vessel wall. This report analyzes the transient heat transfer in the vessel and calculates the thermal deflection and stress that will result from the boiling liquid in contact with the vessel walls. This analysis was applied to aluminum and stainless steel vessels

Electrolytic dissociation of NH{sub 2}K in liquid ammonia; Dissociation electrolytique de NH{sub 2}K dans NH{sub 3} liquide

Energy Technology Data Exchange (ETDEWEB)

Botter, F [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

By assuming the Debye and Huckel approximation giving the activity coefficient and the Onsager relationship linking the conductivity and infinite dilution conductivity of an electrolyte, it has been possible using the available literature data and the electrical conductivity measurements carried out for this purpose, to calculate certain typical parameters of the dissociation of potassium amide in liquid ammonia in the temperature range of -77 deg. C to -33.5 deg. C: degree of dissociation, mean activity coefficient of the ions NH{sub 2}{sup -} and K{sup +}, and the mean activity of these ions. (author) [French] En admettant l'approximation de Debye et Huckel donnant le coefficient d'activite et la relation d'Onsager reliant conductivite et conductivite a dilution infinie d'un electrolyte, on a, en se basant sur les donnees bibliographiques disponibles et des mesures de conductivite electrique effectuees a cette fin, determine par un calcul, certains parametres caracteristiques de la dissociation de l'amidure de potassium dans l'ammoniac liquide dans un domaine de temperature de -77 deg. C a -33,5 deg. C: degre de dissociation, coefficient d'activite moyen des ions NH{sub 2}{sup -} et K{sup +} et activite moyenne de ces ions. (auteur)

In-Situ Liquid Hydrogenation of m-Chloronitrobenzene over Fe-Modified Pt/Carbon Nanotubes Catalysts

Directory of Open Access Journals (Sweden)

Feng Li

2018-02-01

Full Text Available In-situ liquid-phase hydrogenation of m-chloronitrobenzene (m-CNB based on aqueous-phase reforming (APR of ethanol and catalytic hydrogenation was carried out over Fe-modified Pt/carbon nanotubes (CNTs catalysts. The effects of Pt loading over CNTs and Fe modification on the catalytic performance of Pt/CNTs catalysts were studied. In-tube loading of Pt particles, compared with out-tube loading, considerably improved the catalytic activity. With in-tube loading, Fe-modified Pt/CNTs catalysts further improved the m-CNB in-situ hydrogenation performance. After Fe modification, Pt–Fe/CNTs catalysts formed, inside CNTs, a Pt–Fe alloy and iron oxides, which both improved catalytic hydrogenation performance and significantly enhanced ethanol APR hydrogen producing performance, thereby increasing the m-CNB in-situ hydrogenation reactivity.

Vapor-liquid equilibrium prediction with pseudo-cubic equation of state for binary mixtures containing hydrogen, helium, or neon

Energy Technology Data Exchange (ETDEWEB)

Kato, M.; Tanaka, H. (Nihon Univ.,Fukushima, (Japan). Faculty of Enineering)

1990-03-01

As an equation of state of vapor-liquid equilibrium, an original pseudo-cubic equation of state was previously proposed by the authors of this report and its study is continued. In the present study, new effective critical values of hydrogen, helium and neon were determined empirically from vapor-liquid equilibrium data of literature values against their critical temperatures, critical pressures and critical volumes. The vapor-liquid equilibrium relations of binary system quantum gas mixtures were predicted combining the conventinal pseudo-cubic equation of state and the new effective critical values, and without using binary heteromolecular interaction parameter. The predicted values of hydrogen-ethylene, helium-propane and neon-oxygen systems were compared with literature values. As a result, it was indicated that the vapor-liquid relations of binary system mixtures containing hydrogen, helium and neon can be predicted with favorable accuracy combining the effective critical values and the three parameter pseudo-cubic equation of state. 37 refs., 3 figs., 4 tabs.

Evidence for a first-order liquid-liquid transition in high-pressure hydrogen from ab initio simulations.

Science.gov (United States)

Morales, Miguel A; Pierleoni, Carlo; Schwegler, Eric; Ceperley, D M

2010-07-20

Using quantum simulation techniques based on either density functional theory or quantum Monte Carlo, we find clear evidence of a first-order transition in liquid hydrogen, between a low conductivity molecular state and a high conductivity atomic state. Using the temperature dependence of the discontinuity in the electronic conductivity, we estimate the critical point of the transition at temperatures near 2,000 K and pressures near 120 GPa. Furthermore, we have determined the melting curve of molecular hydrogen up to pressures of 200 GPa, finding a reentrant melting line. The melting line crosses the metalization line at 700 K and 220 GPa using density functional energetics and at 550 K and 290 GPa using quantum Monte Carlo energetics.

KARAKTERISASI DAN AKTIVITAS KATALITIK BERBAGAI VARIASI KOMPOSISI KATALIS Ni DAN ZnBr2 DALAM Γ-Al2O3 UNTUK ISOMERISASI DAN HIDROGENASI (R-(+-SITRONELAL

Directory of Open Access Journals (Sweden)

ED Iftitah

2014-06-01

Full Text Available Pengaruh sifat dan karakter berbagai variasi komposisi katalis Ni dan ZnBr2 yang terimpregnasi dalam γ-Al2O3 terhadap aktivitas dan selektivitasnya untuk reaksi isomerisasi dan hidrogenasi (R-(+-Sitronelal telah dilakukan. Dalam penelitian ini, terdapat tiga jenis variasi komposisi Ni dan ZnBr2 dalam γ-Al2O3, yaitu: A1=Ni/ZnBr2/γ-Al2O3 (3:2, A2=Ni/ZnBr2/γ-Al2O3 (1:1 dan A3=Ni/ZnBr2/γ-Al2O3 (2:3. Katalis dikarakterisasi menggunakan X-ray diffraction (XRD, Brunauer-Emmett-Teller (BET surface area, dan SEM-EELS. Luas area permukaan spesifik dan porositasnya ditentukan berdasarkan adsorption-desorption gas nitrogen pada 77 K. Distribusi dan volume pori ditentukan dengan desorption isotherm pada P/Po ≥ 0,3. Hasil yang didapat menunjukkan bahwa terdapat hubungan antara karakter dan sifat katalis dengan aktivitas katalitiknya terhadap produk isomerisasi dan hidrogenasi (R-(+-Sitronelal. Uji aktivitas dilakukan dalam sebuah reaktor mini dengan 0,5 g katalis dan 3 mL (R-(+-Sitronelal menggunakan atmosfir gas N2 dan/atau H2 dalam waktu 5 dan 24 jam masing-masing pada suhu 90 dan 120 °C. Komposisi katalis, pemilihan jenis atmosfir gas dan suhu sangat berpengaruh terhadap aktivitas dan selektivitas pembentukan produk isomerisasi dan hidrogenasi. Konversi (R-(+-Sitronelal tertinggi ditunjukkan oleh katalis A3=Ni/ZnBr2/γ-Al2O3 (2:3 dengan kondisi reaksi selama 5 jam (4 jam N2 + 1 jam H2 pada suhu 90 °C dan 24 jam (4 jam N2 + 20 jam H2 pada suhu 120 °C. The influence of catalyst properties and characteristics of Ni and ZnBr2 catalysts impregnated in γ-Al2O3 on the activity and selectivity of (R-(+-Citronellal isomerisation and hydrogenation has been done. In this study, there were three sets of Ni and ZnBr2 in γ-Al2O3 with various composition, they were A1=Ni/ZnBr2/γ-Al2O3 (3:2, A2=Ni/ZnBr2/γ-Al2O3 (1:1, A3=Ni/ZnBr2/γ-Al2O3 (2:3. The catalysts were characterized using X-ray diffraction (XRD, Brunauer-Emmett-Teller (BET surface area and SEM

Hydrogen bonding in protic ionic liquids: structural correlations, vibrational spectroscopy, and rotational dynamics of liquid ethylammonium nitrate

Science.gov (United States)

Zentel, Tobias; Overbeck, Viviane; Michalik, Dirk; Kühn, Oliver; Ludwig, Ralf

2018-02-01

The properties of the hydrogen bonds in ethylammonium nitrate (EAN) are analyzed by using molecular dynamics simulations and infrared as well as nuclear magnetic resonance experiments. EAN features a flexible three-dimensional network of hydrogen bonds with moderate strengths, which makes it distinct from related triethylammonium-based ionic liquids. First, the network’s flexibility is manifested in a not very pronounced correlation of the hydrogen bond geometries, which is caused by rapid interchanges of bonding partners. The large flexibility of the network also leads to a substantial broadening of the mid-IR absorption band, with the contributions due to N-H stretching motions ranging from 2800 to 3250 cm-1. Finally, the different dynamics are also seen in the rotational correlation of the N-H bond vector, where a correlation time as short as 16.1 ps is observed.

Temperature effects on the behavior of liquid hydrogen isotopes inside a spherical-shell directly driven inertial confinement fusion target

International Nuclear Information System (INIS)

Kim, K.; Mok, L.S.

1984-05-01

The present work studies the temperature effects on the formation of a uniform liquid hydrogen layer inside a spherical glass shell (SGS). The profile of the liquid layer is first investigated for an isothermal case. An equation suitable for describing the profile is derived by including the London-van der Waals attractive forces between the liquid and substrate molecules. Two theoretical models are then established to explain the changes in the liquid layer profile under the influence of a vertically applied temperature gradient. The characteristics of the fluid flows are obtained by solving the fluid equations under the low-Reynolds-number approximations. The effect of the component separation both in the liquid layer and the vapor region, which is induced by the temperature gradient, is studied when the enclosure inside the SGS is a mixture of hydrogen isotopes. A uniform layer can also be formed for the mixture liquid except that the required temperature gradient is now positive in direction, unlike the case of the single-component liquid. The heating effect due to the radioactive decay of tritium is also evaluated. An experimental apparatus capable of generating a desired temperature gradient across the SGS at liquid hydrogen temperatures is described. The profiles of the liquid layer are observed for different temperature gradients and the results are in qualitative agreement with the theoretical predictions

Hydrogen system (hydrogen fuels feasibility)

International Nuclear Information System (INIS)

Guarna, S.

1991-07-01

This feasibility study on the production and use of hydrogen fuels for industry and domestic purposes includes the following aspects: physical and chemical properties of hydrogen; production methods steam reforming of natural gas, hydrolysis of water; liquid and gaseous hydrogen transportation and storage (hydrogen-hydride technology); environmental impacts, safety and economics of hydrogen fuel cells for power generation and hydrogen automotive fuels; relevant international research programs

A method of estimating hydrogen in solid and liquid samples by means of neutron thermalisation

International Nuclear Information System (INIS)

Carter, D.H.; Sanders, J.E.

1967-06-01

The count-rate of a cadmium-covered Pu239 fission chamber placed in a reactor neutron flux increases when a hydrogen-containing material is inserted due to the thermalisation of epicadmium neutrons. This effect forms the basis of a non-destructive method of estimating hydrogen in solid or liquid samples, and trial experiments to demonstrate the principles have been made. The sensitivity is such that hydrogen down to 10 p.p.m. in a typical metal should be detected. A useful feature of the method is its very low response to elements other than hydrogen. (author)

Ionic liquid and solid HF equivalent amine-poly(hydrogen fluoride) complexes effecting efficient environmentally friendly isobutane-isobutylene alkylation.

Science.gov (United States)

Olah, George A; Mathew, Thomas; Goeppert, Alain; Török, Béla; Bucsi, Imre; Li, Xing-Ya; Wang, Qi; Marinez, Eric R; Batamack, Patrice; Aniszfeld, Robert; Prakash, G K Surya

2005-04-27

Isoparaffin-olefin alkylation was investigated using liquid as well as solid onium poly(hydrogen fluoride) catalysts. These new immobilized anhydrous HF catalysts contain varied amines and nitrogen-containing polymers as complexing agents. The liquid poly(hydrogen fluoride) complexes of amines are typical ionic liquids, which are convenient media and serve as HF equivalent catalysts with decreased volatility for isoparaffin-olefin alkylation. Polymeric solid amine:poly(hydrogen fluoride) complexes are excellent solid HF equivalents for similar alkylation acid catalysis. Isobutane-isobutylene or 2-butene alkylation gave excellent yields of high octane alkylates (up to RON = 94). Apart from their excellent catalytic performance, the new catalyst systems significantly reduce environmental hazards due to the low volatility of complexed HF. They represent a new, "green" class of catalyst systems for alkylation reactions, maintaining activity of HF while minimizing its environmental hazards.

A study on the isotopic exchange between hydrogen and water on a catalyst in the liquid phase; Etude de l'echange isotopique entre l'hydrogene et l'eau sur catalyseur en phase liquide

Energy Technology Data Exchange (ETDEWEB)

Dirian, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Montarnal, R; Balaceanu, J C [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

1958-07-01

It is well known that catalytic exchange in the liquid phase offers many advantages over exchange in the gaseous phase; however the rate of reaction is much smaller in the former case. The object of the following work is to study the influence of the various parameters on which the reaction rate depends (pressure, temperature, concentration, agitation), to classify catalysts according to their activity and to determine the economic possibility of liquid phase exchange. (author) [French] Il est un fait bien connu que l'echange catalytique en phase liquide presente divers avantages, compare a l'echange en phase gazeuse; la vitesse de reaction est toute fois beaucoup plus faible que dans le premier cas. L'objet du present rapport est d'etudier l'influence des differents parametres agissant sur la vitesse de reaction (pression, temperature, concentration, agitation), de classer les catalyseurs en fonction de leur activite et d'evaluer les possibilites economiques de l'echange en phase liquide. (auteur)

Capacity enhancement of aqueous borohydride fuels for hydrogen storage in liquids

International Nuclear Information System (INIS)

Schubert, David; Neiner, Doinita; Bowden, Mark; Whittemore, Sean; Holladay, Jamie; Huang, Zhenguo; Autrey, Tom

2015-01-01

Highlights: • Adjusting ratio of Q = Na/B will maximize H 2 storage capacity of liquid carrier. • Mixtures of hydrolysis products are desirable to maximize solubility. • 6.5 wt.% hydrogen and remains liquid from beginning to end. - Abstract: In this work we demonstrate enhanced hydrogen storage capacities through increased solubility of sodium borate product species in aqueous media achieved by adjusting the sodium (NaOH) to boron (B(OH) 3 ) ratio, i.e., M/B, to obtain a distribution of polyborate anions. For a 1:1 mol ratio of NaOH to B(OH) 3 , M/B = 1, the ratio of the hydrolysis product formed from NaBH 4 hydrolysis, the sole borate species formed and observed by 11 B NMR is sodium metaborate, NaB(OH) 4 . When the ratio is 1:3 NaOH to B(OH) 3 , M/B = 0.33, a mixture of borate anions is formed and observed as a broad peak in the 11 B NMR spectrum. The complex polyborate mixture yields a metastable solution that is difficult to crystallize. Given the enhanced solubility of the polyborate mixture formed when M/B = 0.33 it should follow that the hydrolysis of sodium octahydrotriborate, NaB 3 H 8 , can provide a greater storage capacity of hydrogen for fuel cell applications compared to sodium borohydride while maintaining a single phase. Accordingly, the hydrolysis of a 23 wt.% NaB 3 H 8 solution in water yields a solution having the same complex polyborate mixture as formed by mixing a 1:3 M ratio of NaOH and B(OH) 3 and releases >8 eq of H 2 . By optimizing the M/B ratio a complex mixture of soluble products, including B 3 O 3 (OH) 5 2− , B 4 O 5 (OH) 4 2− , B 3 O 3 (OH) 4 − , B 5 O 6 (OH) 4 − and B(OH) 3 , can be maintained as a single liquid phase throughout the hydrogen release process. Consequently, hydrolysis of NaB 3 H 8 can provide a 40% increase in H 2 storage density compared to the hydrolysis of NaBH 4 given the decreased solubility of sodium metaborate

Computational study of the signature of hydrogen-bond strength on the infrared spectra of a hydrogen-bonded complex dissolved in a polar liquid

International Nuclear Information System (INIS)

Hanna, Gabriel; Geva, Eitan

2010-01-01

The signature of hydrogen-bond strength on the one- and two-dimensional infrared spectra of the hydrogen-stretch in a hydrogen-bonded complex dissolved in a polar liquid was investigated via mixed quantum-classical molecular dynamics simulations. Non-Condon effects were found to intensify with increasing hydrogen-bond strength and to shift oscillator strength from the stable configurations that correspond to the ionic and covalent tautomers into unstable configurations that correspond to the transition-state between them. The transition-state peak is observed to blue shift and increase in intensity with increasing hydrogen-bond strength, and to dominate the spectra in the case of a strong hydrogen-bond. It is argued that the application of multidimensional infrared spectroscopy in the region of the transition-state peak can provide a uniquely direct probe of the molecular events underlying breaking and forming of hydrogen-bonds in the condensed phase.

Ionization study of hydrogen in a pulsed discharge; Etude de l'ionisation de l'hydrogene dans une decharge pulsee

Energy Technology Data Exchange (ETDEWEB)

Breton, C [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-02-01

The time variation of the spectral line intensities for molecular and atomic hydrogen in pulsed discharges is interpreted in terms of a model describing the instantaneous population densities of each of the species: H{sub 2} H{sub 2}{sup +} H{sub 3}{sup +}, excited atoms in a level j, electrons and protons. Every possible reaction is taken into account. For plasma diameters of about 25 cm and particle densities of the order of 10{sup 14} cm{sup -3}, it is necessary to introduce transient line absorption coefficients. It is found experimentally that the model describes the observed phenomena reasonably well. From the calculations a method for electron temperature measurement is deduced which uses a single oscillogram giving H{sub {beta}} line intensity versus time. (author) [French] On interprete l'evolution de l'intensite des raies spectrales de l'hydrogene moleculaire et atomique dans une decharge torique pulsee (T.A. 2000) a l'aide d'un modele analytique. Ce modele permet le calcul des populations instantanees de chacune des especes de particules presentes: H{sub 2} H{sub 2}{sup +} H{sub 3}{sup +}, atomes excites sur un niveau j, electrons, protons. On analyse les diverses reactions possibles. Le diametre (25 cm) et la densite ( NH 10{sup 14} cm{sup -3}) du plasma necessitent de tenir compte de la reabsorption des raies de l'atome d'hydrogene. Les tests experimentaux permettent de penser que le modele decrit assez bien les phenomenes observes. On deduit des calculs une methode de mesure de la temperature electronique qui utilise un seul oscillogramme donnant l'evolution de l'intensite relative de la raie H{sub {beta}} pendant une decharge. (auteur)

Optical modulation in nematic phase of halogen substituted hydrogen bonded liquid crystals

Science.gov (United States)

Vijayakumar, V. N.; Madhu Mohan, M. L. N.

2012-01-01

A series of halogen-substituted hydrogen-bonded liquid crystalline complexes have been designed and synthesised. A successful attempt has been made to form complementary hydrogen bonding between the dodecyloxy benzoic acid (12BAO) and halogen-substituted benzoic acids and the physical properties exhibited by the individual complexes are studied. The complexes obtained are analysed by polarising optical microscope (POM), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR) and dielectric studies. The formation of complementary hydrogen bond is confirmed through FTIR spectra. An interesting feature of this series is the observation of a field-induced transition (FiT) in nematic phase. Another interesting phenomenon is the observation of a new smectic X phase (worm-like texture) in all the synthesised complexes. Dielectric relaxation studies in the smectic C phase of these hydrogen bonded complexes along with the Arrhenius and the Cole-Cole plots are discussed. Optical tilt angle in smectic C phase and the corresponding fitted data analysis concur with the Mean field theory prediction.

650 mm long liquid hydrogen target for use in a high intensity electron beam

International Nuclear Information System (INIS)

Mark, J.W.

1983-07-01

This paper describes a 650 mm long liquid hydrogen target constructed for use in the high intensity electron beam at the Stanford Linear Accelerator Center. The main design problem was to construct a target that would permit the heat deposited by the electron beam to be removed rapidly without boiling the hydrogen so as to maintain constant target density for optimum data taking. Design requirements, construction details and operating experience are discussed

Hydrogen extraction from liquid lithium-lead alloy by bubbling with rotational jet nozzle

International Nuclear Information System (INIS)

Xie Bo; Yang Tongzai; Guan Rui; Weng Kuiping

2010-01-01

The technology of tritium extraction from lithium-lead alloy has been simulated, hydrogen extraction from lithium-lead alloy by bubbling with rotational jet nozzle being used to simulate tritium in the study based on the introduction of fluid dynamics to establish algebraic model. The results show that the higher than lithium-lead melting temperature, the higher cumulative hydrogen extraction efficiency, and gas holdup of bubble column is little affected by the impeller diameter. Gas holdup when using small aperture is slightly higher when using large aperture only at a high helium flow rate, but the smaller the aperture, the greater the bubble surface area, and a marked increase in intensity of flow circulation for liquid lithium-lead with the increase of helium flow rate, hydrogen extraction rate increases too. Moreover, influence of the jet rotational velocity on hydrogen extraction is limited. (authors)

Pengaruh Perlakuan Limbah dan Jenis Mordan Kapur, Tawas, dan Tunjung Terhadap Mutu Pewarnaan Kain Sutera dan Katun Menggunakan Limbah Cair Gambir (Uncaria gambir Roxb

Directory of Open Access Journals (Sweden)

Sofyan Sofyan

2015-12-01

Full Text Available Gambier is an extract obtained from heat extraction of leaves and twigs of gambier plant followed by compression, sedimentation, and the formed paste is moulded and then dried. According to West Sumatra in figures, total production of gambier in West Sumatera in 2012 reached 14,220 tons. From the amount would be produced approximately 5,688,000 liters of liquid waste per year. The gambier waste is a by product of gambier production process which is untapped. High tannin content in the liquid waste is a dye that can be used as a textiles dye. The purpose of the research was to utilize liquid waste from gambier production process to dye silk and cotton fabrics with liquid waste treatment which was not stabilized or stabilized with mordant lime (CaCO3, alum Al2(SO43, and tunjung (FeSO4. The results of the research showed that dyeing with liquid waste by using different mordant would generate different colors. Silk and cotton fabrics were dyed with waste, whether stabilized or not stabilized and mordanted with lime, alum, and tunjung generated a reddish brown color,  bright yellow, and moss green respectively. When compared between silk and cotton, color absorption on silk was better. It could be seen from the darker color for the same treatment. The analysis results of color fastness to washing 40°C, the bright day light, and heat pressing generally ranged between good to excellent (scale 4-5.ABSTRAKGambir adalah getah yang diperoleh dari ekstraksi panas daun dan ranting tanaman gambir yang diikuti pengempaan, sedimentasi, dan pasta yang terbentuk dicetak lalu dikeringkan. Menurut Sumatera Barat dalam angka, total produksi gambir Sumatera Barat selama tahun 2012 mencapai 14.220 ton. Dari jumlah tersebut akan dihasilkan lebih kurang 5.688.000 liter limbah cair per tahun. Limbah gambir merupakan hasil samping dari proses produksi gambir yang belum dimanfaatkan. Kandungan tanin yang tinggi dalam limbah cair ini merupakan bahan pewarna yang dapat

Kinetic energy of solid and liquid para-hydrogen: a path integral Monte Carlo simulation

International Nuclear Information System (INIS)

Zoppi, M.; Neumann, M.

1992-01-01

The translational (center of mass) kinetic energy of solid and liquid para-hydrogen have been recently measured by means of Deep Inelastic Neutron Scattering. We have evaluated the same quantity, in similar thermodynamic conditions, by means of Path Integral Monte Carlo computer simulation, modelling the system as composed of a set of spherical molecules interacting through a pairwise additive Lennard-Jones potential. In spite of the crude approximations on the interaction potential, the agreement is excellent. The pressure was also computed by means of the same simulations. This quantity, compared with the equation of state for solid para-hydrogen given by Driessen and Silvera, gives an agreement of a lesser quality and a negative value for the liquid state. We attribute this discrepancy to the limitations of the Lennard-Jones potential. (orig.)

Measurements of hydrogen concentration in liquid sodium by using an inert gas carrier method

International Nuclear Information System (INIS)

Funada, T.; Nihei, I.; Yuhara, S.; Nakasuji, T.

1979-01-01

A technique was developed to measure the hydrogen level in liquid sodium using an inert gas carrier method. Hydrogen was extracted into an inert gas from sodium through a thin nickel membrane in the form of a helically wound tube. The amount of hydrogen in the inert gas was analyzed by gas chromatography. The present method is unique in that it can be used over the wide range of sodium temperatures (150 to 700 0 C) and has no problems associated with vacuum systems. The partial pressure of hydrogen in sodium was determined as a function of cold-trap temperature (T/sub c/). Sieverts' constant (K/sub s/) was determined as a function of sodium temperature (T). From Sieverts' constant, the solubility of hydrogen in sodium is calculated. It was found that other impurities in sodium, such as (O) and (OH), have little effect on the hydrogen pressure in the sodium loop

Measurement of dissolved hydrogen and hydrogen gas transfer in a hydrogen-producing reactor

Energy Technology Data Exchange (ETDEWEB)

Shizas, I.; Bagley, D.M. [Toronto Univ., ON (Canada). Dept. of Civil Engineering

2004-07-01

This paper presents a simple method to measure dissolved hydrogen concentrations in the laboratory using standard equipment and a series of hydrogen gas transfer tests. The method was validated by measuring hydrogen gas transfer parameters for an anaerobic reactor system that was purged with 10 per cent carbon dioxide and 90 per cent nitrogen using a coarse bubble diffuser stone. Liquid samples from the reactor were injected into vials and hydrogen was allowed to partition between the liquid and gaseous phases. The concentration of dissolved hydrogen was determined by comparing the headspace injections onto a gas chromatograph and a standard curve. The detection limit was 1.0 x 10{sup -5} mol/L of dissolved hydrogen. The gas transfer rate for hydrogen in basal medium and anaerobic digester sludge was used to validate the method. Results were compared with gas transfer models. In addition to monitoring dissolved hydrogen in reactor systems, this method can help improve hydrogen production potential. 1 ref., 4 figs.

Study of a pulsed discharge in hydrogen using the far ultraviolet emission of an additional element: electron temperature measurement; Etude d'une decharge pulsee dans l'hydrogene a partir de l'emission dans l'ultraviolet lointain d'un element additionnel: mesure de la temperature electronique

Energy Technology Data Exchange (ETDEWEB)

Schwob, J L [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-06-15

Ionization and excitation of an additional element in a pulsed annular discharge in hydrogen at low pressure (T.A.2000) are described by means of a simple coronal type analytical model. This model allows us to interpret the time variation of the intensity of spectral lines observed in the vacuum ultraviolet region. From this analysis two methods of electron temperature determination are deduced. The first method is based on the apparition time measurement of the intensity maximum for the spectral lines emitted from successive ions of the additional element (nitrogen). In the second method the electron temperature is determined from the intensity ratio of two spectral lines of an alkali-like ion. The transition couples (2s-2p, 2s-3p) and (2s-2p, 3s-3p) of C IV, N V and O VI have been used. The results obtained with these two independent methods are in good agreement. The electron temperature varies from a few electron-volts at the beginning of the discharge, to 70 eV at the time of N V emission (at 55 {mu}s), before the current maximum in the discharge (at 170 {mu}s). (author) [French] On etudie l'ionisation et l'excitation d'un element additionnel dans une decharge annulaire pulsee dans l'hydrogene sous faible pression (T.A.2000) a ralde d'un modele analytique simple du type coronal. Ce modele permet d'interpreter l'evolution de l'intensite des raies spectrales observees dans l'ultraviolet lointain. On deduit de cette etude deux methodes de determination de la temperature electronique. La premiere est basee sur la meaure des temps d'apparition des maximums d'intensite des raies emises par les ions successifs de l'element additionnel (azote). Dans la deuxieme methode la temperature est determinee a partir du rapport d'intensite des deux raies d'un ion alcalinoide. On a utilise les couples de transitions (2s-2p, 2s-3p) et (2e-2p, 3s-3p) des ions C IV, N V et 0 VI. Les resultats obtenus par ces deux voies independantes montrent un assez bon accord. La temperature

Application of gamma densitometer for measurement of void fraction in liquid hydrogen moderator of HANARO cold neutron source

International Nuclear Information System (INIS)

Kim, Myong-Seop; Choi, Jungwoon; Sun, Gwang-Min; Lee, Kye-Hong

2009-01-01

The void fraction in the liquid hydrogen used for the moderator of the HANARO cold neutron source (CNS) was measured by using a gamma densitometer technique. A mock-up of the HANARO CNS facility with an electric heating system as the heat source instead of radiations was constructed. The photon transmissions through the hydrogen moderator were simulated to search for an optimum experimental condition. From the simulation, it was confirmed that Am-241 was suitable for the measurement of the void fraction in the liquid hydrogen medium. A gamma densitometer using the Am-241 gamma-ray source was designed and installed at the mock-up of the CNS. The attenuation of 59.5 keV gamma-rays from the Am-241 through the hydrogen medium was measured by using an HPGe detector. The void fraction was determined using the amount of the gamma-ray attenuation. The void fractions in the hydrogen moderator were measured for stable thermo-siphon loops with several electric heat loads applied to the moderator cell of the CNS mock-up. The longitudinal distribution of the void fraction inside the moderator cell was also determined. The void fraction measured at a heat load of 720 W had values of 8-41% depending on the height from the bottom of the moderator cell. The overall void fraction was obtained by volume-weighted averaging of its longitudinal distribution. The void fraction at the nuclear heating power expected at the normal operation condition of the HANARO CNS facility was determined to be about 20%. The large uncertainty was expected in the void fraction determination by a gamma densitometer for the liquid hydrogen medium with the void fraction less than 10%. When the void fraction of the liquid hydrogen was near 20%, the uncertainty in the void fraction determination by using a gamma densitometer became relatively small, and it was regarded as an acceptable level. The measurements for the void fraction will be very useful for the design and operation of the HANARO CNS.

Thermophysical properties of hydrogen along the liquid-vapor coexistence

Science.gov (United States)

Osman, S. M.; Sulaiman, N.; Bahaa Khedr, M.

2016-05-01

We present Theoretical Calculations for the Liquid-Vapor Coexistence (LVC) curve of fluid Hydrogen within the first order perturbation theory with a suitable first order quantum correction to the free energy. In the present equation of state, we incorporate the dimerization of H2 molecule by treating the fluid as a hard convex body fluid. The thermophysical properties of fluid H2 along the LVC curve, including the pressure-temperature dependence, density-temperature asymmetry, volume expansivity, entropy and enthalpy, are calculated and compared with computer simulation and empirical results.

Two-dimensional thermal analysis of liquid hydrogen tank insulation

Energy Technology Data Exchange (ETDEWEB)

Babac, Gulru; Sisman, Altug [Istanbul Technical University, Energy Institute, Ayazaga campus, 34469 Maslak, Istanbul (Turkey); Cimen, Tolga [Jaguar and Landrover, Banbury Road, Gaydon, Warwick CV35 0RR (United Kingdom)

2009-08-15

Liquid hydrogen (LH{sub 2}) storage has the advantage of high volumetric energy density, while boil-off losses constitute a major disadvantage. To minimize the losses, complicated insulation techniques are necessary. In general, Multi Layer Insulation (MLI) and a Vapor-Cooled Shield (VCS) are used together in LH{sub 2} tanks. In the design of an LH{sub 2} tank with VCS, the main goal is to find the optimum location for the VCS in order to minimize heat leakage. In this study, a 2D thermal model is developed by considering the temperature dependencies of the thermal conductivity and heat capacity of hydrogen gas. The developed model is used to analyze the effects of model considerations on heat leakage predictions. Furthermore, heat leakage in insulation of LH{sub 2} tanks with single and double VCS is analyzed for an automobile application, and the optimum locations of the VCS for minimization of heat leakage are determined for both cases. (author)

Intensity enhancement of cold neutrons from a coupled liquid-hydrogen moderator for pulsed cold neutron sources

International Nuclear Information System (INIS)

Ogawa, Y.; Kiyanagi, Y.; Kosugi, N.; Iwasa, H.; Furusaka, M.; Watanabe, N.

1999-01-01

In order to obtain higher cold neutron intensity from a coupled liquid-hydrogen moderator with a premoderator for pulsed cold neutron sources, we examined a partial enhancement method, namely, narrow beam extraction for both a flat liquid-hydrogen moderator and a single-groove one. Combined with the narrow beam extraction, which is especially suitable for small-angle scattering and neutron reflectometry experiments, a single-groove moderator provides higher intensity, by about 30%, than a flat-surface moderator at the region of interest on a viewed surface. The effect of double-side beam extraction from such moderators on the intensity gain factor is also discussed. (author)

Capacity enhancement of aqueous borohydride fuels for hydrogen storage in liquids

Energy Technology Data Exchange (ETDEWEB)

Schubert, David; Neiner, Doinita [U.S. Borax Inc., Rio Tinto, Greenwood Village, CO (United States); Bowden, Mark [Environmental Molecular Sciences Laboratory, Pacific Northwest National Laboratory, Richland, WA (United States); Whittemore, Sean; Holladay, Jamie [Pacific Northwest National Laboratory, Richland, WA (United States); Huang, Zhenguo [Institute for Superconducting and Electronic Materials, University of Wollongong, Wollongong, NSW 2500 (Australia); Autrey, Tom [Pacific Northwest National Laboratory, Richland, WA (United States)

2015-10-05

Highlights: • Adjusting ratio of Q = Na/B will maximize H{sub 2} storage capacity of liquid carrier. • Mixtures of hydrolysis products are desirable to maximize solubility. • 6.5 wt.% hydrogen and remains liquid from beginning to end. - Abstract: In this work we demonstrate enhanced hydrogen storage capacities through increased solubility of sodium borate product species in aqueous media achieved by adjusting the sodium (NaOH) to boron (B(OH){sub 3}) ratio, i.e., M/B, to obtain a distribution of polyborate anions. For a 1:1 mol ratio of NaOH to B(OH){sub 3}, M/B = 1, the ratio of the hydrolysis product formed from NaBH{sub 4} hydrolysis, the sole borate species formed and observed by {sup 11}B NMR is sodium metaborate, NaB(OH){sub 4}. When the ratio is 1:3 NaOH to B(OH){sub 3}, M/B = 0.33, a mixture of borate anions is formed and observed as a broad peak in the {sup 11}B NMR spectrum. The complex polyborate mixture yields a metastable solution that is difficult to crystallize. Given the enhanced solubility of the polyborate mixture formed when M/B = 0.33 it should follow that the hydrolysis of sodium octahydrotriborate, NaB{sub 3}H{sub 8}, can provide a greater storage capacity of hydrogen for fuel cell applications compared to sodium borohydride while maintaining a single phase. Accordingly, the hydrolysis of a 23 wt.% NaB{sub 3}H{sub 8} solution in water yields a solution having the same complex polyborate mixture as formed by mixing a 1:3 M ratio of NaOH and B(OH){sub 3} and releases >8 eq of H{sub 2}. By optimizing the M/B ratio a complex mixture of soluble products, including B{sub 3}O{sub 3}(OH){sub 5}{sup 2−}, B{sub 4}O{sub 5}(OH){sub 4}{sup 2−}, B{sub 3}O{sub 3}(OH){sub 4}{sup −}, B{sub 5}O{sub 6}(OH){sub 4}{sup −} and B(OH){sub 3}, can be maintained as a single liquid phase throughout the hydrogen release process. Consequently, hydrolysis of NaB{sub 3}H{sub 8} can provide a 40% increase in H{sub 2} storage density compared to the hydrolysis

An overview of dehydration, aldol-condensation and hydrogenation processes for production of liquid alkanes from biomass-derived carbohydrates

Energy Technology Data Exchange (ETDEWEB)

Chheda, Juben N.; Dumesic, James A. [University of Wisconsin-Madison, Department of Chemical and Biological Engineering, Madison, WI 53706 (United States)

2007-05-30

We present results for the conversion of carbohydrate feedstocks to liquid alkanes by the combination of dehydration, aldol-condensation/hydrogenation, and dehydration/hydrogenation processing. With respect to the first dehydration step, we demonstrate that HMF can be produced in good selectivity from abundantly available polysaccharides (such as inulin, sucrose) containing fructose monomer units using a biphasic batch reactor system. The reaction system can be optimized to achieve good yields to 5-hydroxymethylfurfural (HMF) from fructose by varying the contents of aqueous-phase modifiers such as dimethylsulfoxide (DMSO) and 1-methyl-2-pyrrolidinone (NMP). Regarding the aldol-condensation/hydrogenation step, we present the development of stable, solid base catalysts in aqueous environments. We address the effects of various reaction parameters such as the molar ratio of reactants and temperature on overall product yield for sequential aldol-condensation and hydrogenation steps. Overall, our results show that it is technically possible to convert carbohydrate feedstocks to produce liquid alkanes by the combination of dehydration, aldol-condensation/hydrogenation, and dehydration/hydrogenation processing; however, further optimization of these processes is required to decrease the overall number of separate steps (and reactors) required in this conversion. (author)

Design of a Helium Vapor Shroud for Liquid Hydrogen Fueling of an Unmanned Aerial Vehicle (UAV)

Science.gov (United States)

Cavender, K.; Evans, C.; Haney, J.; Leachman, J.

2017-12-01

Filling a vehicular liquid hydrogen fuel tank presents the potential for flammable mixtures due to oxygen concentration from liquid air condensation. Current liquid hydrogen tank designs utilize insulating paradigms such as aerogel/fiberglass materials, vacuum jackets, or inert gas purge systems to keep the outer surface from reaching the condensation temperature of air. This work examines the heat transfer at the refuelling connection of the tank to identify potential areas of condensation, as well as the surface temperature gradient. A shrouded inert gas purge was designed to minimize vehicle weight and refuelling time. The design of a shrouded inert gas purge system is presented to displace air preventing air condensation. The design investigates 3D printed materials for an inert gas shroud, as well as low-temperature sealing designs. Shroud designs and temperature profiles were measured and tested by running liquid nitrogen through the filling manifold. Materials for the inert gas shroud are discussed and experimental results are compared to analytical model predictions. Suggestions for future design improvements are made.

Vibrational signatures of cation-anion hydrogen bonding in ionic liquids: a periodic density functional theory and molecular dynamics study.

Science.gov (United States)

Mondal, Anirban; Balasubramanian, Sundaram

2015-02-05

Hydrogen bonding in alkylammonium based protic ionic liquids was studied using density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations. Normal-mode analysis within the harmonic approximation and power spectra of velocity autocorrelation functions were used as tools to obtain the vibrational spectra in both the gas phase and the crystalline phases of these protic ionic liquids. The hydrogen bond vibrational modes were identified in the 150-240 cm(-1) region of the far-infrared (far-IR) spectra. A blue shift in the far-IR mode was observed with an increasing number of hydrogen-bonding sites on the cation; the exact peak position is modulated by the cation-anion hydrogen bond strength. Sub-100 cm(-1) bands in the far-IR spectrum are assigned to the rattling motion of the anions. Calculated NMR chemical shifts of the acidic protons in the crystalline phase of these salts also exhibit the signature of cation-anion hydrogen bonding.

Assessment of liquid hydrogen cooled MgB2 conductors for magnetically confined fusion

International Nuclear Information System (INIS)

Glowacki, B A; Nuttall, W J

2008-01-01

Importantly environmental factors are not the only policy-driver for the hydrogen economy. Over the timescale of the development of fusion energy systems, energy security issues are likely to motivate a shift towards both hydrogen production and fusion as an energy source. These technologies combine local control of the system with the collaborative research interests of the major energy users in the global economy. A concept Fusion Island Reactor that might be used to generate H 2 (rather than electricity) is presented. Exploitation of produced hydrogen as a coolant and as a fuel is proposed in conjunction with MgB 2 conductors for the tokomak magnets windings, and electrotechnical devices for Fusion Island's infrastructure. The benefits of using MgB 2 over the Nb-based conductors during construction, operation and decommissioning of the Fusion Island Reactor are presented. The comparison of Nb 3 Sn strands for ITER fusion magnet with newly developed high field composite MgB 2 PIT conductors has shown that at 14 Tesla MgB 2 possesses better properties than any of the Nb 3 Sn conductors produced. In this paper the potential of MgB 2 conductors is examined for tokamaks of both the conventional ITER type and a Spherical Tokamak geometry. In each case MgB 2 is considered as a conductor for a range of field coil applications and the potential for operation at both liquid helium and liquid hydrogen temperatures is considered. Further research plans concerning the application of MgB 2 conductors for Fusion Island are also considered

Thermal and hydrodynamic study of a whirling liquid hydrogen layer under high heat flux

International Nuclear Information System (INIS)

Ewald, R.

1969-01-01

In order to achieve a cold neutrons source (λ ≥ 4.10 -10 m) in a high flux reactor (∼ 10 15 neutrons/cm 2 .s), a whirling liquid hydrogen layer (145 mm OD, effective thickness 15 mm, height about 180 mm) was formed, out-of-pile, in a cylindrical transparent glass vessel. The whirling motion was obtained by tangential injection of the liquid, near the wall. Thermal and hydrodynamical conditions of formation and laws of similarity of such a layer were studied. The characteristics of this whirling flow were observed as a function of mass flow rate (5 to 27 g/s; 4.3 to 23 l/mn), and of spillway width (18 and 25 mm). Six different nozzles were used : 1.0; 1.5; 1.9; 2.25; 2.65 and 3.0 mm ID. The total heat influx was found between 8.6 and 10.4 kW. The heat flux density was about 9.4 W/cm 2 and the mean layer density around 80 per cent of that of the liquid hydrogen at 20.4 Kelvin. High speed movies were used to analyze the boiling regime. (author) [fr

Evaluation of mechanical property data on the 2219 aluminum alloy and application of the data to the design of liquid hydrogen tankage

Science.gov (United States)

Witzell, W. E.

1977-01-01

The potential use of thin guage 2219 aluminum alloy for airborne liquid hydrogen tankage was examined. Existing data were processed using the Newman two parameter equation, a prediction was made for the life expectancy of a hypothetical liquid hydrogen tank, and additional experimental data were generated in an attempt to correct the deficiencies in the existing data.

The hydrogen state: from the solid to the gas taking into account the liquid; L'hydrogene dans tous ses etats: du solide au gaz en passant par le liquide

Energy Technology Data Exchange (ETDEWEB)

Latroche, M.; Joubert, J.M.; Cuevas, F.; Paul-Boncour, V.; Percheron-Guegan, A. [Centre National de la Recherche Scientifique (CNRS), Institut de Chimie et des Materiaux Paris-Est (CMTR-ICMPE-UMR7182), 94 - Thiais (France)

2007-07-01

Hydrogen is considered as a future energy vector. To become a viable solution, the hydrogen storage processes must be safe, economic and adapted to the use possibilities. Today many storage modes offer interesting possibilities but need also more researches before realization of prototypes. These modes are described taking into account the physical (compression, liquefaction) and chemical (adsorption in porous solids and absorption in chemical hydrides) solutions. (A.L.B.)

Experimental studies on hydrogen isotopic deuterium from gas to liquid phase by catalytic exchange

International Nuclear Information System (INIS)

Luo Yangming; Wang Heyi; Liu Jun; Fu Zhonghua; Wang Changbin; Han Jun; Xia Xiulong; Tang Lei

2005-01-01

The experimental studies on hydrogen isotopic deuterium from gas to liquid phase were completed by mixed ratio 1:4 of Pt-SDB hydrophobic catalyst and hydrophilic packing. The influencing factors on number of transfer units (NTU) and transformation efficiencies of deuterium were researched. The results show that preferable NTU can be obtained by choosing suitable operational temperature and flux of exchange gas. The transformation rate increases with increasing liquid flux, but it cannot obviously be improved when liquid flux attains some level. The length of catalytic column has an obvious influence on transformation rate and 90% of transformation rate is obtained by 4 m column length at gas flux with 2 m 3 /h, liquid flux with 1-2 kg/h and 45 degree C. (author)

Ruthenium dioxide nanoparticles in ionic liquids: synthesis, characterization and catalytic properties in hydrogenation of olefins and arenes

International Nuclear Information System (INIS)

Rossi, Liane M.; Dupont, Jairton; Machado, Giovanna; Fichtner, Paulo F.P.; Radtke, Claudio; Baumvol, Israel J.R.; Teixeira, Sergio R.

2004-01-01

The reaction of NaBH 4 with RuCl 3 dissolved in 1-n-butyl-3-methylimidazolium hexafluorophosphate (BMI.PF 6 ) ionic liquid is a simple and reproducible method for the synthesis of stable RuO 2 nanoparticles with a narrow size distribution within 2-3 nm. RuO 2 nanoparticles were characterized by XRD, XPS, EDS and TEM. These nanoparticles showed high catalytic activity either in the solventless or liquid-liquid biphasic hydrogenation of olefins and arenes under mild reaction conditions. Hg(0) and CS 2 poisoning experiments and XRD and TEM analysis of particles isolated after catalysis indicated the formation of Ru(0) nanoparticles. The nanoparticles could be re-used in solventless conditions up to 10 times in the hydrogenation of 1-hexene yielding a total turnover number for exposed Ru atoms of 175,000. (author)

Reaction rates and electrical resistivities of the hydrogen isotopes with, and their solubilities in, liquid lithium

International Nuclear Information System (INIS)

Pulham, R.J.; Adams, P.F.; Hubberstey, P.; Parry, G.; Thunder, A.E.

1976-01-01

The rate of reaction, k, of hydrogen and of deuterium with liquid lithium have been determined up to pressures of 20kNm -2 and at temperatures between 230 and 270 0 C. The reaction is first order with an apparent activation energy of 52.8 and 55.2 kJmol -1 for hydrogen and deuterium, respectively. The deuterium isotope effect, k/sub H/k/sub D/, decreases from 2.95 at 230 to 2.83 at 270 0 C. Tritium is predicted to react even more slowly than deuterium. The freezing point of lithium is depressed by 0.082 and 0.075 0 C, respectively, by dissolved hydride and deuteride giving eutectics at 0.016 mol percent H and 0.012 mol percent D in the metal-salt phase diagrams. The depression and eutectic concentration are expected to be less for tritium. The increase in the resistivity of liquid lithium caused by dissolved hydrogen isotopes is linear and relatively large, 5 x 10 -8 Ωm (mol percent H or D) -1 . The solubility of lithium hydride and deuteride was determined from the marked change in resistivity on saturation. The liquidus of the metal-salt phase diagram rises steeply from the eutectic point to meet the two-immiscible liquid region. Tritium is expected to be less soluble than deuterium. The partial molar enthalpies of solution are 44.2 and 55.0 kJmol -1 for hydrogen and deuterium, respectively. These values are used to calculate the solvation enthalpies of the isotope anions in the metal

Thermodynamics of hydrogen bonding and van der Waals interactions of organic solutes in solutions of imidazolium based ionic liquids: “Structure-property” relationships

International Nuclear Information System (INIS)

Varfolomeev, Mikhail A.; Khachatrian, Artashes A.; Akhmadeev, Bulat S.; Solomonov, Boris N.

2016-01-01

Highlights: • Solution enthalpies of organic solutes in imidazolium based ionic liquids were measured. • van der Waals interactions scale of imidazolium based ionic liquids was proposed. • Enthalpies of solvation of organic solutes in ionic liquids were determined. • Hydrogen bond enthalpies of organic solutes with ionic liquids were calculated. • Relationships between structure of ionic liquids and thermochemical data were obtained. - Abstract: In the present work thermochemistry of intermolecular interactions of organic compounds in solutions of imidazolium based ionic liquids (ILs) has been studied using solution calorimetry method. Enthalpies of solution at infinite dilution of non-polar (alkanes, aromatic hydrocarbons) and polar (alcohols, amides, and etc.) organic solutes in two ionic liquids 1-butyl-3-methylimidazolium tetrafluoroborate and 1-butyl-3-methylimidazolium trifluoromethanesulfonate were measured at 298.15 K. The scale of van der Waals interactions of imidazolium based ILs has been proposed on the basis of solution enthalpies of n-alkanes in their media. The effect of the cation and anion structure of ILs on the enthalpies of solvation was analyzed. Enthalpies of hydrogen bonding of organic solutes with imidazolium based ILs were determined. It has been shown that these values are close to zero for proton acceptor solutes. At the same time, enthalpies of hydrogen bonding of proton donor solutes with ionic liquids are increased depending the anion: tetrafluoroborate ≈ bis(trifluoromethylsulfonyl)imide < 2-(2-methoxyethoxy)ethyl sulfate < trifluoromethanesulfonate. Enthalpies of van der Waals interactions and hydrogen bonding in the solutions of imidazolium based ionic liquids were compared with the same data for molecular solvents.

Thermodynamics of hydrogen bonding and van der Waals interactions of organic solutes in solutions of imidazolium based ionic liquids: “Structure-property” relationships

Energy Technology Data Exchange (ETDEWEB)

Varfolomeev, Mikhail A., E-mail: vma.ksu@gmail.com; Khachatrian, Artashes A.; Akhmadeev, Bulat S.; Solomonov, Boris N.

2016-06-10

Highlights: • Solution enthalpies of organic solutes in imidazolium based ionic liquids were measured. • van der Waals interactions scale of imidazolium based ionic liquids was proposed. • Enthalpies of solvation of organic solutes in ionic liquids were determined. • Hydrogen bond enthalpies of organic solutes with ionic liquids were calculated. • Relationships between structure of ionic liquids and thermochemical data were obtained. - Abstract: In the present work thermochemistry of intermolecular interactions of organic compounds in solutions of imidazolium based ionic liquids (ILs) has been studied using solution calorimetry method. Enthalpies of solution at infinite dilution of non-polar (alkanes, aromatic hydrocarbons) and polar (alcohols, amides, and etc.) organic solutes in two ionic liquids 1-butyl-3-methylimidazolium tetrafluoroborate and 1-butyl-3-methylimidazolium trifluoromethanesulfonate were measured at 298.15 K. The scale of van der Waals interactions of imidazolium based ILs has been proposed on the basis of solution enthalpies of n-alkanes in their media. The effect of the cation and anion structure of ILs on the enthalpies of solvation was analyzed. Enthalpies of hydrogen bonding of organic solutes with imidazolium based ILs were determined. It has been shown that these values are close to zero for proton acceptor solutes. At the same time, enthalpies of hydrogen bonding of proton donor solutes with ionic liquids are increased depending the anion: tetrafluoroborate ≈ bis(trifluoromethylsulfonyl)imide < 2-(2-methoxyethoxy)ethyl sulfate < trifluoromethanesulfonate. Enthalpies of van der Waals interactions and hydrogen bonding in the solutions of imidazolium based ionic liquids were compared with the same data for molecular solvents.

Future hydrogen markets for large-scale hydrogen production systems

International Nuclear Information System (INIS)

Forsberg, Charles W.

2007-01-01

The cost of delivered hydrogen includes production, storage, and distribution. For equal production costs, large users (>10 6 m 3 /day) will favor high-volume centralized hydrogen production technologies to avoid collection costs for hydrogen from widely distributed sources. Potential hydrogen markets were examined to identify and characterize those markets that will favor large-scale hydrogen production technologies. The two high-volume centralized hydrogen production technologies are nuclear energy and fossil energy with carbon dioxide sequestration. The potential markets for these technologies are: (1) production of liquid fuels (gasoline, diesel and jet) including liquid fuels with no net greenhouse gas emissions and (2) peak electricity production. The development of high-volume centralized hydrogen production technologies requires an understanding of the markets to (1) define hydrogen production requirements (purity, pressure, volumes, need for co-product oxygen, etc.); (2) define and develop technologies to use the hydrogen, and (3) create the industrial partnerships to commercialize such technologies. (author)

Solid Catalyst with Ionic Liquid Layer (SCILL). A concept to improve the selectivity of selective hydrogenations

Energy Technology Data Exchange (ETDEWEB)

Jess, A.; Korth, W. [Bayreuth Univ. (Germany). Chair of Chemical Engineering

2011-07-01

Catalytic hydrogenations are important for refinery processes, petrochemical applications as well as for numerous processes of the fine chemicals industry. In some cases, hydrogenations consist of a sequence of consecutive reactions, and the desired product is the intermediate. An important goal is then a high yield and selectivity to the intermediate, if possible at a high conversion degree. The selectivity to an intermediate primarily depends on the chemical nature of the catalyst, but may also be influenced by diffusion processes. Ionic liquids (ILs) are low melting salts (< 100 C) and represent a promising solvent class. This paper focuses on the concept of a Solid Catalyst with Ionic Liquid Layer (SCILL), where the solid catalyst is coated with a thin IL layer to improve the selectivity. (orig.)

Vapour pressure isotope effects in liquid hydrogen chloride

Energy Technology Data Exchange (ETDEWEB)

Lopes, J.N.C.; Calado, J.C.G. (Instituto Superior Tecnico, Lisbon (Portugal)); Jancso, Gabor (Hungarian Academy of Sciences, Budapest (Hungary). Central Research Inst. for Physics)

1992-08-10

The difference between the vapour pressures of HCl and DCl has been measured over the temperature range 170-203 K by a differential manometric technique in a precision cryostat. In this range the vapour pressure of HCl is higher than that of DCl by 3.2% at 170 K, decreasing to 0.9% at 200 K. The reduced partition function ratios f[sub l]/f[sub g] derived from the vapour pressure data can be described by the equation ln(f[sub l]/f[sub g]) = (3914.57[+-]10)/T[sup 2] - (17.730[+-]0.055)/T. The experimentally observed H-D vapour pressure isotope effect, together with the values on the [sup 35]Cl-[sup 37]Cl isotope effect available in the literature, is interpreted in the light of the statistical theory of isotope effects in condensed systems by using spectroscopic data of the vapour and liquid phases. The results indicate that the rotation in liquid hydrogen chloride is hindered. Temperature-dependent force constants for the hindered translational and rotational motions were invoked in order to obtain better agreement between the model calculation and experiment. (author).

Capacity enhancement of aqueous borohydride fuels for hydrogen storage in liquids

Energy Technology Data Exchange (ETDEWEB)

Schubert, David [U.S. Borax Inc., Rio Tinto, CO (United States); Neiner, Doinita [U.S. Borax Inc., Rio Tinto, CO (United States); Bowden, Mark [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Whittemore, Sean [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Holladay, Jamie [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Huang, Zhenguo [Univ. of Wollongong, NSW (Australia); Autrey, Tom [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-10-01

In this work we demonstrate enhanced hydrogen storage capacities through increased solubility of sodium borate product species in aqueous media achieved by adjusting the sodium (NaOH) to boron (B(OH)₃) ratio, i.e., M/B, to obtain a distribution of polyborate anions. For a 1:1 mole ratio of NaOH to B(OH)₃, M/B = 1, the ratio of the hydrolysis product formed from NaBH₄ hydrolysis, the sole borate species formed and observed by 11B NMR is sodium metaborate, NaB(OH)₄. When the ratio is 1:3 NaOH to B(OH)₃, M/B = 0.33, a mixture of borate anions is formed and observed as a broad peak in the 11B NMR spectrum. The complex polyborate mixture yields a metastable solution that is difficult to crystallize. Given the enhanced solubility of the polyborate mixture formed when M/B = 0.33 it should follow that the hydrolysis of sodium octahydrotriborate, NaB₃H₈, can provide a greater storage capacity of hydrogen for fuel cell applications compared to sodium borohydride while maintaining a single phase. Accordingly, the hydrolysis of a 23 wt% NaB₃H₈ solution in water yields a solution having the same complex polyborate mixture as formed by mixing a 1:3 molar ratio of NaOH and B(OH)₃ and releases >8 eq of H₂. By optimizing the M/B ratio a complex mixture of soluble products, including B₃O₃(OH)₅^2-, B₄O₅(OH)₄^2-, B₃O₃(OH)^4-, B₅O₆(OH)^4- and B(OH)₃, can be maintained as a single liquid phase throughout the hydrogen release process. Consequently, hydrolysis of NaB₃H₈ can provide a 40% increase in H₂ storage density compared to the hydrolysis of NaBH₄ given the decreased solubility of sodium metaborate. The authors would like to thank Jim Sisco and Paul Osenar of

Production of liquid alkanes by controlling reactivity of sorbitol hydrogenation with a Ni/HZSM-5 catalyst in water

International Nuclear Information System (INIS)

Zhang, Qing; Wang, Tiejun; Xu, Ying; Zhang, Qi; Ma, Longlong

2014-01-01

Graphical abstract: MCM-41-modified Ni/HZSM-5 catalyst was developed by impregnation method with high catalytic performance for sorbitol hydrogenation in water. Appropriate amount of MCM-41 addition can distinctly promote the improvement in the surface structure and modulation of acidic sites of the catalyst. The scission of C–O bond in the sorbitol molecule into liquid alkanes was easily carried out on the catalyst containing more Lewis acidic sites. - Highlights: • Ni/HZSM-5 promoted with MCM-41 is active for sorbitol hydrogenation to liquid alkanes. • Lewis acidic sites of Ni/HZSM-5 can be modulated by pure silica MCM-41. • MCM-41 added can distinctly decrease carbon deposition on the catalyst surface. - Abstract: Liquid fuels derived from renewable biomass are of great importance on the potential substitution for diminishing fossil fuels. The conversion of sorbitol (a product of biomass-derived glucose hydrogenation) into liquid alkanes such as pentane and hexane over the Ni/HZSM-5 catalysts with or without MCM-41 addition was investigated in the presence of hydrogen in water medium. The production distribution of sorbitol hydrogenation can be controlled by adjusting the acidity of the catalyst. The scission of C–C bond in the sorbitol molecule into light C 1 –C 4 alkanes was mainly carried out over Ni/HZSM-5 containing strong Brønsted acid sites, while C–O bond scission into heavier alkanes was dominated over the catalysts added by MCM-41 containing weak Lewis acid sites. The sorbitol conversion and total liquid alkanes selectivity were found to be 67.1% and 98.7% over 2%Ni/HZSM-5 modified by 40 wt% of MCM-41, whereas the corresponding value was 40% and 35.6% over 2%Ni/HZSM-5 in the absence of MCM-41. The effect of MCM-41 on the structure, acidity, and reducibility of Ni/HZSM-5 was investigated by using XRD, Py-IR, IR, and H 2 -TPR. Meanwhile, the resistance of carbon deposition over the catalyst modified by MCM-41 was studied by using TG�

Static phenomena at the charged surface of liquid hydrogen

International Nuclear Information System (INIS)

Levchenko, A.A.; Kolmakov, G.V.; Mezhov-Deglin, L.P.; Mikhjlov, M.G.; Trusov, A.B.

1999-01-01

The shape evolution of the equipotentially charged surface of liquid hydrogen layer covering the lower plate of a horizontally arranged diode in external electric fields has been studied experimentally for the first time. A reconstruction phenomenon (the formation of a stationary hump) at the flat charged surface at voltages higher than a certain critical U c1 was observed under the conditions of total compensation of the electric field in the bulk liquid by a surface charge. It is shown that the transition of the flat charged surface into the reconstructed state is a phase transition closed to the second order phase transition. The height of the hump increased with increasing the voltage and at U c2 > 1,2 U c1 the reconstructed surface lost the stability, and a stream discharge pulse was observed. The shape evolution of a changed droplet of constant volume suspended at the upper plate of the diode when the stretching electric field and gravity forces act in the same direction was studied as the voltage was increased up to the discharge

Hydrogen vehicle fueling station

Energy Technology Data Exchange (ETDEWEB)

Daney, D.E.; Edeskuty, F.J.; Daugherty, M.A. [Los Alamos National Lab., NM (United States)] [and others

1995-09-01

Hydrogen fueling stations are an essential element in the practical application of hydrogen as a vehicle fuel, and a number of issues such as safety, efficiency, design, and operating procedures can only be accurately addressed by a practical demonstration. Regardless of whether the vehicle is powered by an internal combustion engine or fuel cell, or whether the vehicle has a liquid or gaseous fuel tank, the fueling station is a critical technology which is the link between the local storage facility and the vehicle. Because most merchant hydrogen delivered in the US today (and in the near future) is in liquid form due to the overall economics of production and delivery, we believe a practical refueling station should be designed to receive liquid. Systems studies confirm this assumption for stations fueling up to about 300 vehicles. Our fueling station, aimed at refueling fleet vehicles, will receive hydrogen as a liquid and dispense it as either liquid, high pressure gas, or low pressure gas. Thus, it can refuel any of the three types of tanks proposed for hydrogen-powered vehicles -- liquid, gaseous, or hydride. The paper discusses the fueling station design. Results of a numerical model of liquid hydrogen vehicle tank filling, with emphasis on no vent filling, are presented to illustrate the usefulness of the model as a design tool. Results of our vehicle performance model illustrate our thesis that it is too early to judge what the preferred method of on-board vehicle fuel storage will be in practice -- thus our decision to accommodate all three methods.

Permeation barrier for lightweight liquid hydrogen tanks

Energy Technology Data Exchange (ETDEWEB)

Schultheiss, D.

2007-04-16

For the future usage of hydrogen as an automotive fuel, its on-board storage is crucial. One approach is the storage of liquid hydrogen (LH2, 20 K) in double-walled, vacuum insulated tanks. The introduction of carbon fiber reinforced plastics (CFRP) as structural material enables a high potential of reducing the weight in comparison to the state-of-the-art stainless steel tanks. The generally high permeability of hydrogen through plastics, however, can lead to long-term degradation of the insulating vacuum. The derived objective of this dissertation was to find and apply an adequate permeation barrier (liner) on CFRP. The investigated liners were either foils adhered on CFRP specimens or coatings deposited on CFRP specimens. The coatings were produced by means of thermal spraying, metal plating or physical vapor deposition (PVD). The materials of the liners included Al, Au, Cu, Ni and Sn as well as stainless steel and diamond-like carbon. The produced liners were tested for their permeation behavior, thermal shock resistance and adherence to the CFRP substrate. Additionally, SEM micrographs were used to characterize and qualify the liners. The foils, although being a good permeation barrier, adhered weakly to the substrate. Furthermore, leak-free joining of foil segments is a challenge still to be solved. The metal plating liners exhibited the best properties. For instance, no permeation could be detected through a 50 {mu}m thick Cu coating within the accuracy of the measuring apparatus. This corresponds to a reduction of the permeation gas flow by more than factor 7400 compared to uncoated CFRP. In addition, the metal platings revealed a high adherence and thermal shock resistance. The coatings produced by means of thermal spraying and PVD did not show a sufficient permeation barrier effect. After having investigated the specimens, a 170 liter CFRP tank was fully coated with 50 {mu}m Cu by means of metal plating. (orig.)

Ionization study of hydrogen in a pulsed discharge; Etude de l'ionisation de l'hydrogene dans une decharge pulsee

Energy Technology Data Exchange (ETDEWEB)

Breton, C. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-02-01

The time variation of the spectral line intensities for molecular and atomic hydrogen in pulsed discharges is interpreted in terms of a model describing the instantaneous population densities of each of the species: H{sub 2} H{sub 2}{sup +} H{sub 3}{sup +}, excited atoms in a level j, electrons and protons. Every possible reaction is taken into account. For plasma diameters of about 25 cm and particle densities of the order of 10{sup 14} cm{sup -3}, it is necessary to introduce transient line absorption coefficients. It is found experimentally that the model describes the observed phenomena reasonably well. From the calculations a method for electron temperature measurement is deduced which uses a single oscillogram giving H{sub {beta}} line intensity versus time. (author) [French] On interprete l'evolution de l'intensite des raies spectrales de l'hydrogene moleculaire et atomique dans une decharge torique pulsee (T.A. 2000) a l'aide d'un modele analytique. Ce modele permet le calcul des populations instantanees de chacune des especes de particules presentes: H{sub 2} H{sub 2}{sup +} H{sub 3}{sup +}, atomes excites sur un niveau j, electrons, protons. On analyse les diverses reactions possibles. Le diametre (25 cm) et la densite ( NH 10{sup 14} cm{sup -3}) du plasma necessitent de tenir compte de la reabsorption des raies de l'atome d'hydrogene. Les tests experimentaux permettent de penser que le modele decrit assez bien les phenomenes observes. On deduit des calculs une methode de mesure de la temperature electronique qui utilise un seul oscillogramme donnant l'evolution de l'intensite relative de la raie H{sub {beta}} pendant une decharge. (auteur)

Étude de l'efficacité des modes de Lamb dans la signature acoustique en fonction du liquide de couplage

Science.gov (United States)

Brunet, N.; Cros, B.; Despaux, G.; Saurel, J.-M.

1998-06-01

The acoustic signature allows to measure the velocity of the longitudinal and transverse acoustic waves in bulk materials. From the velocities and density values the elastic properties can be calculated. For thin layer materials, these velocities are not directly measured but computed from the experimentally available velocities: the generalized Lamb waves velocities. These waves velocities are dispersive and their measurement depends on the liquid acting as a coupling fluid. In this study, the two faces of the layer are in contact with the liquid (methanol, water or aqueous solutions of potassium iodide KI_aq. 6 M and potassium hydroxyde KOH_aq. 12 M) chosen according to its acoustic parameters. The acoustic signature modeling allows to know their respective influence, the possible detection of the fast modes and, in general, the velocity measurement accuracy increase for all available modes. The experimental studies bear out that each mode characterization may be optimized by the appropriate choice of the frequency and of the coupling liquid according to its velocity, density and attenuation. L'étude de la signature acoustique permet de mesurer les vitesses de propagation des ondes acoustiques longitudinale et transverse dans les matériaux massifs, vitesses à partir desquelles on détermine leurs propriétés mécaniques. Pour des matériaux en couche mince, ces vitesses ne sont plus mesurées directement mais calculées à partir des vitesses accessibles expérimentalement : celles des modes de Lamb généralisés. Ces modes ont des vitesses dispersives et leur mesure dépend du liquide servant de couplant, dans lequel la couche est immergée. Dans cette étude, les liquides de couplage (méthanol, eau et solutions aqueuses de iodure de potassium KI_aq. 6 M et d'hydroxyde de potassium KOH_aq. 12 M) sont choisis en fonction de leurs paramètres acoustiques. La modélisation de la signature acoustique permet de prévoir leur influence respective, comment ils

The TApIR experiment. IR absorption spectra of liquid hydrogen isotopologues; Das TApIR Experiment IR-Absorptionsspektren fluessiger Wasserstoffisotopologe

Energy Technology Data Exchange (ETDEWEB)

Groessle, Robin

2015-11-27

The scope of the thesis is the infrared absorption spectroscopy of liquid hydrogen isotopologues with the tritium absorption infrared spectroscopy (TApIR) experiment at the tritium laboratory Karlsruhe (TLK). The calibration process from the sample preparation to the reference measurements are described. A further issue is the classical evaluation of FTIR absorption spectra and the extension using the rolling circle filter (RCF) including the effects on statistical and systematical errors. The impact of thermal and nuclear spin temperature on the IR absorption spectra is discussed. An empirical based modeling for the IR absorption spectra of liquid hydrogen isotopologues is performed.

Neutron Scattering of Residual Hydrogen in 1,4-Dioxane-D8 Liquid. Understanding Measurements with Molecular Dynamics Simulations

Energy Technology Data Exchange (ETDEWEB)

de Almeida, Valmor F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Liu, Hongjun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Herwig, Kenneth W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kidder, Michelle [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-01-25

That incoherent scattering from protiated molecular liquids adds a constant background to the measured scattering intensity is well known, but less appreciated is the fact that coherent scattering is also induced by the presence of hydrogen in a deuterated liquid. In fact, the scattering intensity can be very sensitive, in the small-q region, with respect to the amounts and distribution of residual H in the system. We used 1,4-dioxane liquid to demonstrate that the partial structure factors of the HD and DD atom pairs contribute significantly to inter-molecular scattering and that uncertainty in the extent of deuteration account for discrepancies between simulations and measurements. Both contributions to uncertainty have similar magnitudes: scattering interference of the hydrogen-deuterium pair, and complementary interference from the deuterium-deuterium pair by virtue of chemical inhomogeneity. This situation arises in practice since deuteration of liquids is often 99% or less. A combined experimental and extensive computational study of static thermal neutron scattering of 1,4-dioxane demonstrates the foregoing. We show, through simulations, that the reason for the differences is the content of protiated dioxane (vendors quote 1%). We estimate that up to 5% (at 298K and at 343K) protiated mole fraction may be involved in generating the scattering differences. Finally, we find that the particular distribution of hydrogen in the protiated molecules affects the results significantly; here we considered molecules to be either fully protiated or fully deuterated. This scenario best reconciles the computational and experimental results, and leads us to speculate that the deuteration synthesis process tends to leave a molecule either fully deuterated or fully protiated. Although we have used 1,4-dioxane as a model liquid, the effects described in this study extend to similar liquids and similar systematic experimental/computational studies can be performed to either

Density functional theory study on the ionic liquid pyridinium hydrogen sulfate

Science.gov (United States)

Tankov, Ivaylo; Yankova, Rumyana; Genieva, Svetlana; Mitkova, Magdalena; Stratiev, Dicho

2017-07-01

The geometry, electronic structure and chemical reactivity of a pyridinium-based ionic liquid, pyridinium hydrogen sulfate ([H-Pyr]+[HSO4]-), have been discussed on the basis of quantum chemical density functional theory calculations using B3LYP/6-311+G(d,p) and B3LYP/6-311++G(2d,2p) approaches. The calculations indicated that [H-Pyr]+[HSO4]- exists in the form of an ion pair. A large electropositive potential was found on the pyridinium ring, while the regions of a negative electrostatic potential is linked with the lone pair of electronegative oxygen atoms in hydrogen sulfate anion ([HSO4]-). Electron transfer both within the anion, and between the anion and cation of an ion pair were described using natural bond orbital theory. The energy values of -7.1375 and -2.8801 eV were related to HOMO and LUMO orbitals, respectively.

C1 Chemistry for the Production of Ultra-Clean Liquid Transportation Fuels and Hydrogen

Energy Technology Data Exchange (ETDEWEB)

Gerald P. Huffman

2005-03-31

Faculty and students from five universities--the University of Kentucky, University of Pittsburgh, University of Utah, West Virginia University, and Auburn University--are collaborating in a research program to develop C1 chemistry processes to produce ultra-clean liquid transportation fuels and hydrogen, the zero-emissions transportation fuel of the future. The feedstocks contain one carbon atom per molecular unit. They include synthesis gas (syngas), a mixture of carbon monoxide and hydrogen produced by coal gasification or reforming of natural gas, methane, methanol, carbon dioxide, and carbon monoxide. An important objective is to develop C1 technology for the production of liquid transportation fuel and hydrogen from domestically plentiful resources such as coal, coalbed methane, and natural gas. An Industrial Advisory Board with representatives from Chevron-Texaco, Eastman Chemical, Conoco-Phillips, the Air Force Research Laboratory, the U.S. Army National Automotive Center (Tank & Automotive Command--TACOM), and Tier Associates provides guidance on the practicality of the research. The current report presents results obtained in this research program during the six months of the subject contract from October 1, 2002 through March 31, 2003. The results are presented in thirteen detailed reports on research projects headed by various faculty members at each of the five CFFS Universities. Additionally, an Executive Summary has been prepared that summarizes the principal results of all of these projects during the six-month reporting period.

Medium temperature reaction between lanthanide and actinide carbides and hydrogen; Reaction a temperature moyenne entre les monocarbures de lanthanides et d'actinides et l'hydrogene

Energy Technology Data Exchange (ETDEWEB)

Dean, G; Lorenzelli, R; Pascard, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1964-07-01

Hydrogen is fixed reversibly by the lanthanide and actinide mono carbides in the range 25 - 400 C, as for pure corresponding metals. Hydrogen goes into the carbides lattice through carbon vacancies and the total fixed amount is approximately equal to two hydrogen atoms per initial vacancy. Final products c.n thus be considered as carbo-hydrides of general formula M(C{sub 1-x}, H{sub 2x}). The primitive CFC, NaCl type, structure remains unchanged but expands strongly in the case of actinide carbides. With lanthanide carbides, hydrogenation induces a phase transformation with reappearance of the metal structure (HCP). Hydrogen decomposition pressures of all the studied carbo-hydrides are greater than those of the corresponding di-hydrides. (authors) [French] Les monocarbures d'actinides et de lanthanides fixent reversiblement de l'hydrogene a temperature peu elevee, a peu pres dans les memes conditions que les metaux purs correspondants. L'hydrogene penetre dans le reseau des carbures par l'intermediaire des lacunes de carbone, et la quantite totale fixee est approximativement egale a deux atomes d'hydrogene par lacune initiale. Les produits obtenus peuvent donc etre consideres comme des carbohydrures de formule generale M(C{sub 1-x}, H{sub 2x}). La structure d'origine CFC, type NaCl est conservee, mais avec une forte expansion, dans le cas des carbures d'actinides. En revanche, l'hydrogenation entraine un changement de phase cristalline avec retour a la structure du metal (HC) pour les carbures de lanthanides. Tous les carbohydrures etudies ont des tensions de decomposition en hydrogene superieures a celles des dihydrures correspondants. (auteurs)

Etiology and radiologic findings of anoxia occurred at Dan-Mu-Ji(Salted radish in rice bran) manufacture: A case report and results of gas analysis

Energy Technology Data Exchange (ETDEWEB)

Park, Choong Ki; Kim, Heung Cheol; Ahn, Bum Gyu; Park, Man Soo; Hwang, Woo Cheol; Choi, Cheol Soon; Kang, Ik Won [College of Medicine, Hallym University, Chunchon (Korea, Republic of); Kim, Man Goo [Kangwon National University, Chunchon (Korea, Republic of)

1994-07-15

To identify the main toxic gas released from salted radish in rice bran(Dan-Mu-Ji) and to introduce the radiological findings of the patient who was exposed to the gas. Chest radiographs and CT scans of one survivor among three men who were exposed to the gas from Dan-Mu-Ji were reviewed. Gas obtained from the closed bottle containing Dan-Mu-Ji was analyzed by using the gas chromatography. The radiographic examinations of the survivor were suggestive of pulmonary edema with it's rapidly improving consideration in both lung. The headspace gas within the bottle containing Dan-Mu-Ji was mainly composed with carbon dioxide, ethyl alcohol and hydrogen sulfide, of which hydrogen sulfide was considered the main toxic gas released. Under the anaerobic condition, Dan-Mu-Ji released toxic hydrogen sulfide. Inhalation of hydrogen sulfide might produce non-cardiogenic pulmonary edema.

Hydrogen bonding in ionic liquids.

Science.gov (United States)

Hunt, Patricia A; Ashworth, Claire R; Matthews, Richard P

2015-03-07

Ionic liquids (IL) and hydrogen bonding (H-bonding) are two diverse fields for which there is a developing recognition of significant overlap. Doubly ionic H-bonds occur when a H-bond forms between a cation and anion, and are a key feature of ILs. Doubly ionic H-bonds represent a wide area of H-bonding which has yet to be fully recognised, characterised or explored. H-bonds in ILs (both protic and aprotic) are bifurcated and chelating, and unlike many molecular liquids a significant variety of distinct H-bonds are formed between different types and numbers of donor and acceptor sites within a given IL. Traditional more neutral H-bonds can also be formed in functionalised ILs, adding a further level of complexity. Ab initio computed parameters; association energies, partial charges, density descriptors as encompassed by the QTAIM methodology (ρBCP), qualitative molecular orbital theory and NBO analysis provide established and robust mechanisms for understanding and interpreting traditional neutral and ionic H-bonds. In this review the applicability and extension of these parameters to describe and quantify the doubly ionic H-bond has been explored. Estimating the H-bonding energy is difficult because at a fundamental level the H-bond and ionic interaction are coupled. The NBO and QTAIM methodologies, unlike the total energy, are local descriptors and therefore can be used to directly compare neutral, ionic and doubly ionic H-bonds. The charged nature of the ions influences the ionic characteristics of the H-bond and vice versa, in addition the close association of the ions leads to enhanced orbital overlap and covalent contributions. The charge on the ions raises the energy of the Ylp and lowers the energy of the X-H σ* NBOs resulting in greater charge transfer, strengthening the H-bond. Using this range of parameters and comparing doubly ionic H-bonds to more traditional neutral and ionic H-bonds it is clear that doubly ionic H-bonds cover the full range of weak

Infra-red spectra of systems containing hydrogen-bonds; Spectres dans l'infrarouge de corps a liaison hydrogene

Energy Technology Data Exchange (ETDEWEB)

Marechal, Y [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1969-07-01

du type X-H...Y et X-H...Y. En supposant que le mouvement X-H...Y est harmonique, mais depend parametriquement de la distance X...Y, et en tenant compte de l'interaction entre differentes liaisons hydrogene, nous pouvons reconstituer quantitativement les spectres des corps tels que l'imidazole et les dimeres d'acide acetique, qui forment les spectres les mieux resolus experimentalement. L'effet isotopique (remplacement de H par D) decoule tout naturellement de cette supposition, et le spectre experimental des corps deuteres est reconstitue quantitativement, sans aucune hypothese supplementaire, ce qui nous donne une confirmation independante de la validite de notre theorie. Nous etendons ces considerations au cas de cristaux a liaison hydrogene en vue d'une reconstitution future de leurs spectres infrarouge. Par sa signification physique, notre theorie s'oppose aux theories proposees anterieurement, qui ne tenaient pas compte de ce mecanisme de couplage ni de l'interaction entre liaisons hydrogene. Ces theories anterieures n'ont pas recu, a notre connaissance, de verification quantitative. Aussi notre reconstitution quantitative des spectres a structure complexe de l'imidazole et de l'acide acetique, ainsi que notre prevision correcte de l'effet isotopique, semblent indiquer que le mecanisme propose est le facteur principal qui intervient dans les differents mouvements d'elongation de la liaison hydrogene. (auteur)

Decomposition of methane hydrate for hydrogen production using microwave and radio frequency in-liquid plasma methods

International Nuclear Information System (INIS)

Rahim, Ismail; Nomura, Shinfuku; Mukasa, Shinobu; Toyota, Hiromichi

2015-01-01

This research involves two in-liquid plasma methods of methane hydrate decomposition, one using radio frequency wave (RF) irradiation and the other microwave radiation (MW). The ultimate goal of this research is to develop a practical process for decomposition of methane hydrate directly at the subsea site for fuel gas production. The mechanism for methane hydrate decomposition begins with the dissociation process of methane hydrate formed by CH_4 and water. The process continues with the simultaneously occurring steam methane reforming process and methane cracking reaction, during which the methane hydrate is decomposed releasing CH_4 into H_2, CO and other by-products. It was found that methane hydrate can be decomposed with a faster rate of CH_4 release using microwave irradiation over that using radio frequency irradiation. However, the radio frequency plasma method produces hydrogen with a purity of 63.1% and a CH conversion ratio of 99.1%, which is higher than using microwave plasma method which produces hydrogen with a purity of 42.1% and CH_4 conversion ratio of 85.5%. - Highlights: • The decomposition of methane hydrate is proposed using plasma in-liquid method. • Synthetic methane hydrate is used as the sample for decomposition in plasma. • Hydrogen can be produced from decomposition of methane hydrate. • Hydrogen purity is higher when using radio frequency stimulation.

Hydrogen-plasticity in the austenitic alloys; Interactions hydrogene-plasticite dans les alliages austenitiques

Energy Technology Data Exchange (ETDEWEB)

De lafosse, D. [Ecole Nationale Superieure des Mines, Lab. PECM-UMR CNRS 5146, 42 - Saint-Etienne (France)

2007-07-01

This presentation deals with the hydrogen effects under stresses corrosion, in austenitic alloys. The objective is to validate and characterize experimentally the potential and the limits of an approach based on an elastic theory of crystal defects. The first part is devoted to the macroscopic characterization of dynamic hydrogen-dislocations interactions by aging tests. then the hydrogen influence on the plasticity is evaluated, using analytical classic models of the elastic theory of dislocations. The hydrogen influence on the flow stress of bcc materials is analyzed experimentally with model materials. (A.L.B.)

Kinetics of tritium isotope exchange between liquid pyrrole and gaseous hydrogen

International Nuclear Information System (INIS)

Stolarz, A.

1994-01-01

The kinetics of tritium isotope exchange between liquid pyrrole and gaseous hydrogen has been studied over the temperature range of 290-303 K. The reaction was carried out in the presence of platinum black but in spite of that, it appeared to be relatively slow. The kinetics of the exchange reaction studied could be described by the simple McKay equation. The results obtained suggest that diffusion is the rate-determining step. A mechanism of exchange is proposed. (author) 10 refs.; 2 figs.; 1 tab

Process for exchanging hydrogen isotopes between gaseous hydrogen and water

International Nuclear Information System (INIS)

Hindin, S. G.; Roberts, G. W.

1980-01-01

A process for exchanging isotopes of hydrogen, particularly tritium, between gaseous hydrogen and water is provided whereby gaseous hydrogen depeleted in tritium and liquid or gaseous water containing tritium are reacted in the presence of a metallic catalyst

Change of hydrogen bonding structure in ionic liquid mixtures by anion type

Science.gov (United States)

Cha, Seoncheol; Kim, Doseok

2018-05-01

Ionic liquid mixtures have gained attention as a way of tuning material properties continuously with composition changes. For some mixture systems, physicochemical properties such as excess molar volume have been found to be significantly different from the value expected by linear interpolation, but the origin of this deviation is not well understood yet. The microstructure of the mixture, which can range from an ideal mixture of two initial consisting ionic liquids to a different structure from those of pure materials, has been suggested as the origin of the observed deviation. The structures of several different ionic liquid mixtures are studied by IR spectroscopy to confirm this suggestion, as a particular IR absorption band (νC(2)-D) for the moiety participating in the hydrogen bonding changes sensitively with the change of the anion in the ionic liquid. The absorbance of νC(2)-D changes proportionally with the composition, and a relatively small excess molar volume is observed for the mixtures containing an electronegative halide anion. By contrast, the absorbance changes nonlinearly, and the excess molar volumes are larger for the mixtures of which one of the anions has multiple interaction sites.

Study on supported binary sulfide catalysts for secondary hydrogenation of coal-derived liquids; Sekitan ekikayu niji suisoka shokubai no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimada, H.; Matsubayashi, N.; Sato, T.; Imamura, M.; Yoshimura, Y.; Nishijima, A. [National Institute of Materials and Chemical Research, Tsukuba (Japan)

1995-07-28

To utilize the high performance of supported catalysts in coal liquefaction processes, one of the promising ways is to apply hydroprocessing sulfide catalysts to the secondary hydrogenation of coal-derived liquids which have undergone the solid separation unit. However, when the product yield from the first-stage liquefaction is maximized, the feed stocks in the secondary hydrogenation contain large amounts of residual fractions with preasphaltenes and metallic components. In this case, the development of a long-life catalyst is essential to establish the two-stage process as a practical one. From this viewpoint, the authors have investigated the deactivation causes of supported Ni-Mo sulfide catalysts through the analysis of the used catalysts in the secondary hydrogenation of coal-derived liquids for long periods. The major cause of the catalyst deactivation has been found to be metallic and carbonaceous deposition on the catalyst, which results thin layer which covers the catalyst particles. The catalysts located at the reactor inlet are more rapidly deactivated than those at the rector exit because of larger amounts of metallic foul ants and the above described shell-like layer. Hydrocracking active sites are much heavily deactivated compared with hydrogenation active sites. It is inferred that the basic or polar compounds contained in coal liquids are permanency adsorbed on the hydrocracking active sites. Spectroscopic analysis of the used catalysts clarified the destruction of the active phase of the binary sulfides, through the segregation and crystal growth. The structural changes of the catalysts are very likely caused by heteroatom compounds in the preasphaltenes. Thus, the primary cause of the catalyst deactivation is the preasphaltenes in the coal liquids. Hydroaromatic compounds in the coal liquids suppress the change of the deposited carbonaceous materials into inert coke which permanently deactivate the catalyst.

Hydrogen bonding discotic liquid crystals: Synthesis, self-assembly, and molecular recognition

Science.gov (United States)

Bushey, Mark Lawrence

The triamides shown below form discotic liquid crystalline phases with intermolecular hydrogen bonding stabilizing the columnar structure, A and B. The mesomorphic orientations of the columns are dependent on the amide side chain. Three mesophasic orientations are described: columns aligned perpendicular to the surface, columns aligned parallel to the surface in a radial pattern, and columns aligned parallel to the surface in a parallel or aligned pattern. The aggregation of the tridodecyloxy-triamides show N-H shifting in the IR at elevated temperatures, an indication that hydrogen bonding is important in the association of liquid crystalline mesophases. Powder X-ray diffraction studies indicate packing of the columns into a hexagonal lattice.* Studies on triamides with chiral side chains result in molecules stacking into columns displaying a helical pitch. In concentrated solutions of dodecane, molecules with chiral side chains display behavior consistent with chiral nematic liquid crystals; a super helical packing of the chiral columns. These superhelical packed systems show temperature dependent selective reflection of visible light and fingerprint textures. Atomic force microscopy (AFM) confirms in sub-monolayer films, that molecules preferring an edge-on orientation form long columns on highly ordered pyrolytic graphite (HOPG), those that prefer a face-on orientation form large amorphous domains. Electrostatic force microscopy (EFM) images of the domains of molecules in the edge-on orientation provides no discernible polarity, imaging of the domains of molecules in the face-on orientation indicates a negative polar orientation. Scanning probe measurements (SPM) of the tridodecynyl-triamide have shown similar edge-on orientations of other tridodecyloxy-triamides. Powder X-ray diffraction of these liquid crystalline phases shows a hexagonal packing of the columnar assembly. Electro-optic switching studies indicate a piezoelectric switching mechanism, possibly

Analysis of the Quasi-Elastic Scattering of Neutrons in Hydrogenous Liquids

Energy Technology Data Exchange (ETDEWEB)

Porohit, S N [Nuclear Science and Engineering Dept., Rensselaer Polytechnique Inst., Troy, NY (United States)

1966-11-15

A critical discussion of the quasi-elastic scattering of neutrons by incoherent (hydrogenous) liquids is presented. Using the line shape expression a comparative discussion of several phenomenological models has been carried out. Extension of the Singwi-Sjoelander zero phonon expression, for the jump-diffusion model, so as to include the one phonon expression has also been given. For a delayed diffusion model a complete treatment of S(K, {omega}) is presented. Along the lines of the macroscopic diffusion cooling, a microscopic diffusion cooling effect in fluids is speculated.

Analysis of the Quasi-Elastic Scattering of Neutrons in Hydrogenous Liquids

International Nuclear Information System (INIS)

Porohit, S.N.

1966-11-01

A critical discussion of the quasi-elastic scattering of neutrons by incoherent (hydrogenous) liquids is presented. Using the line shape expression a comparative discussion of several phenomenological models has been carried out. Extension of the Singwi-Sjoelander zero phonon expression, for the jump-diffusion model, so as to include the one phonon expression has also been given. For a delayed diffusion model a complete treatment of S(K, ω) is presented. Along the lines of the macroscopic diffusion cooling, a microscopic diffusion cooling effect in fluids is speculated

Systematic study of the use of electrical fields for improving heat exchange in boiling liquids; Etude systematique de l'utilisation de champs electriques pour l'amelioration des echanges thermiques dans des liquides bouillants

Energy Technology Data Exchange (ETDEWEB)

Bochirol, L; Bonjour, E; Lagnier, R; Verdier, J; Weil, L [Commissariat a l' Energie Atomique, Grenoble (France).Centre d' Etudes Nucleaires

1961-07-01

We have studied, at the boiling point, for liquids with various electrical properties (hexane, benzene, trichloroethylene, demineralized water, acetone, methyl-ethyl-ketone, etc...) the effect of the application of electric fields on the exchange coefficients and on the maximum dissipative powers before calefaction. We have given the mechanism of the significant improvements obtained (multiplication by a factor of 2 to 10): - in the natural convection zone by showing the role played by the dielectric properties of the liquids under study; - in the zone of nuclear boiling by analysis of the forces acting on the boiling nuclei. Finally we give some experimental results concerning measurements made under pressure until local boiling occurred: they show the possibility of some interesting applications of the method. (author) [French] On a etudie, a l'ebullition, sur des liquides de caracteristiques electriques diverses (hexane, benzene, trichlorethylene, eau demineralisee, acetone, methylethylcetone, etc...) les effets de l'application de champs electriques sur les coefficients d'echanges et les puissances maximales dissipables avant calefaction. On a precise le mecanisme des ameliorations importantes obtenues (multiplication par un facteur 2 a 10): - dans la zone de convection naturelle en mettant en evidence le role des caracteristiques dielectriques des liquides etudies; - dans la zone d'ebullition nucleaire par analyse des forces mises en jeu sur les noyaux d'ebullition. On donne enfin des resultats experimentaux sur des mesures effectuees sous pression jusqu'a l'ebullition locale: ils illustrent des possibilites d'applications interessantes du procede. (auteur)

Hydrogen Bond Induces Hierarchical Self-Assembly in Liquid-Crystalline Block Copolymers.

Science.gov (United States)

Huang, Shuai; Pang, Linlin; Chen, Yuxuan; Zhou, Liming; Fang, Shaoming; Yu, Haifeng

2018-03-01

Microphase-separated structures of block copolymers (BCs) with a size of sub-10 nm are usually obtained by hydrogen-bond-induced self-assembly of BCs through doping with small molecules as functional additives. Here, fabrication of hierarchically self-assembled sub-10 nm structures upon microphase separation of amphiphilic liquid-crystalline BCs (LCBCs) at the existence of hydrogen bonds but without any dopants is reported. The newly introduced urethane groups in the side chain of the hydrophobic block of LCBCs interact with the ether groups of the hydrophilic poly(ethylene oxide) (PEO) block, leading to imperfect crystallization of the PEO blocks. Both crystalline and amorphous domains coexist in the separated PEO phase, enabling a lamellar structure to appear inside the PEO nanocylinders. This provides an elegant method to fabricate controllable sub-10 nm microstructures in well-defined polymer systems without the introduction of any dopants. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

New hydrogen technologies

International Nuclear Information System (INIS)

1992-01-01

This report presents an overview of the overall hydrogen system. There are separate sections for production, distribution, transport, storage; and applications of hydrogen. The most important methods for hydrogen production are steam reformation of natural gas and electrolysis of water. Of the renewable energy options, production of hydrogen by electrolysis using electricity from wind turbines or by gasification of biomass were found to be the most economic for Finland. Direct use of this electricity or the production of liquid fuels from biomass will be competing alternatives. When hydrogen is produced in the solar belt or where there is cheap hydropower it must be transported over long distances. The overall energy consumed for the transport is from 25 to 40 % of the initial available energy. Hydrogen storage can be divided into stationary and mobile types. The most economic, stationary, large scale hydrogen storage for both long and short periods is underground storage. When suitable sites are not available, then pressure vessels are the best for short period and liquid H 2 for long period. Vehicle storage of hydrogen is by either metal hydrides or liquid H 2 . Hydrogen is a very versatile energy carrier. It can be used to produce heat directly in catalytic burners without flame, to produce electricity in fuel cells with high efficiency for use in vehicles or for peak power shaving, as a fuel component with conventional fuels to reduce emissions, as a way to store energy and as a chemical reagent in reactions

Enzymatic exchange of sulphur between cysteine and hydrogen sulphide in the yolk sac of an incubated bird's egg; Echange enzymatique entre le soufre de la cysteine et celui de l'hydrogene sulfure dans le sac vitellin de l'oeuf embryonne d'oiseau

Energy Technology Data Exchange (ETDEWEB)

Chapeville, F; Fromageot, P [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

Previous work has shown that the formation of cysteic acid from sulphate in incubated hen's eggs is due to the following reactions: a) reduction of sulphate to sulphite by the yolk sac endoderm cells; b) synthesis of cysteic acid from the sulphite in the presence of cysteine with liberation of hydrogen sulphide: HS-CH{sub 2}-CH(NH{sub 2})-COOH + SO{sub 3}H{sup -} {yields} H{sub 2}S + {sup -}O{sub 3}S-CH{sub 2}-CH(NH{sub 2})-COOH (1). The enzymatic system responsible for this reaction is localized on the yolk sac endoderm and in the yolk. It may be wondered whether reaction (1) is not made up of two consecutive reactions, one of which is reversible: HS-CH{sub 2}-CH(NH{sub 2})-COOH {r_reversible} H{sub 2}S + organic chain (2) and organic chain + SO{sub 3}H{sup -} {yields} {sup -}O{sub 3}S-CH{sub 2}-CH(NH{sub 2})-COOH (3). It would then be clear why the addition of sulphite displaces the equilibrium towards the production of cysteic acid and hydrogen sulphide. If this is the case, the addition of ordinary cysteine and of marked hydrogen sulphide to the biological medium should make it possible to detect the formation of {sup 35}S cysteine. The present work shows that the desulphurization of the cysteine (reaction 2) by the yolk sac + the yolk is in fact a reversible reaction, and that an enzymatic exchange occurs between the sulphur of the cysteine and that of the hydrogen sulphide. (author) [French] Un precedent travail a montre que la formation de l'acide cysteique a partir de sulfate dans l'oeuf embryonne de poule correspond aux reactions suivantes: a) Reduction du sulfate en sulfite par les cellules de l'endoderme du sac vitellin; b) synthese de l'acide cysteique a partir du sulfite en presence de cysteine avec liberation de l'hydrogene sulfure: HS-CH{sub 2}-CH(NH{sub 2})-COOH + SO{sub 3}H{sup -} {yields} H{sub 2}S + {sup -}O{sub 3}S-CH{sub 2}-CH(NH{sub 2})-COOH (1). Le systeme enzymatique responsable de cette reaction est localise dans l'endoderme du sac vitellin

The Advanced High-Temperature Reactor (AHTR) for Producing Hydrogen to Manufacture Liquid Fuels

International Nuclear Information System (INIS)

Forsberg, C.W.; Peterson, P.F.; Ott, L.

2004-01-01

Conventional world oil production is expected to peak within a decade. Shortfalls in production of liquid fuels (gasoline, diesel, and jet fuel) from conventional oil sources are expected to be offset by increased production of fuels from heavy oils and tar sands that are primarily located in the Western Hemisphere (Canada, Venezuela, the United States, and Mexico). Simultaneously, there is a renewed interest in liquid fuels from biomass, such as alcohol; but, biomass production requires fertilizer. Massive quantities of hydrogen (H2) are required (1) to convert heavy oils and tar sands to liquid fuels and (2) to produce fertilizer for production of biomass that can be converted to liquid fuels. If these liquid fuels are to be used while simultaneously minimizing greenhouse emissions, nonfossil methods for the production of H2 are required. Nuclear energy can be used to produce H2. The most efficient methods to produce H2 from nuclear energy involve thermochemical cycles in which high-temperature heat (700 to 850 C) and water are converted to H2 and oxygen. The peak nuclear reactor fuel and coolant temperatures must be significantly higher than the chemical process temperatures to transport heat from the reactor core to an intermediate heat transfer loop and from the intermediate heat transfer loop to the chemical plant. The reactor temperatures required for H2 production are at the limits of practical engineering materials. A new high-temperature reactor concept is being developed for H2 and electricity production: the Advanced High-Temperature Reactor (AHTR). The fuel is a graphite-matrix, coated-particle fuel, the same type that is used in modular high-temperature gas-cooled reactors (MHTGRs). The coolant is a clean molten fluoride salt with a boiling point near 1400 C. The use of a liquid coolant, rather than helium, reduces peak reactor fuel and coolant temperatures 100 to 200 C relative to those of a MHTGR. Liquids are better heat transfer fluids than gases

Recycling the liquid fraction of alkaline hydrogen peroxide in the pretreatment of corn stover.

Science.gov (United States)

Alencar, Bárbara Ribeiro Alves; Reis, Alexandre Libanio Silva; de Souza, Raquel de Fatima Rodrigues; Morais, Marcos Antônio; Menezes, Rômulo Simões Cezar; Dutra, Emmanuel Damilano

2017-10-01

The aim of this study was to evaluate the influence of recycling the liquid fraction of pretreatment with alkaline hydrogen peroxide (AHP) on the hydrolysis of corn stover. Corn stover was pretreated in the traditional condition with 7.5% v/v H 2 O 2 . After pretreatment, the solids were separated from the liquid fraction and five successive reuse cycles of the liquid fraction were tested. The solid fraction from pretreatment in each recycle was submitted to enzymatic hydrolysis. The number of recycles had a linear negative effect (R 2 =0.98) on biomass delignification efficiency and also affected negatively the enzymatic conversion efficiency. Despite the decrease in efficiency after each recycling step, reuse of the liquid fraction leads to reduction in water, H 2 O 2 and NaOH consumption of up to 57.6%, 59.6% and 57.6%, respectively. These findings point to an efficient recycling technology, which may reduce costs and save water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bavarian liquid hydrogen bus demonstration project - safety, licensing and acceptability aspects

Energy Technology Data Exchange (ETDEWEB)

Wurster, R.; Knorr, H.; Pruemm, W.

1999-07-01

A regular 12 m city bus of the MAN SL 202 type with an internal combustion engine adapted to hydrogen operation and auxiliary gasoline operation was demonstrated in the Bavarian cities of Erlangen and Munich between April 1996 and August 1998. Three bus operators, Erlanger Stadtwerke, Stadtwerke Muenchen and Autobus Oberbayern were testing the bus in three different operating schemes. In order to be able to perform this worldwide first public demonstration of a liquid hydrogen (LH{sub 2}) city bus in regular service, several requirements with respect to safety, licensing, training and acceptability had to be fulfilled. These activities were focusing mainly on the hydrogen specific issues such as (a) integration of onboard LH{sub 2} storage vessels, piping and instrumentation, (b) implementation of storage and refueling infrastructure in the operators' yards, (c) adaptation of the maintenance garages, (d) training of operating and maintenance personnel. During phase II of the demonstration activity a poll was performed on passengers traveling onboard the hydrogen-powered city bus in order to determined the level of acceptance among the users of the bus. The bus was designed and manufactured by MAN Nutzfahrzeuge Aktiengesellschaft. The cryogenic fuel storage and the refueling equipment were designed and manufactured by Linde AG. The realization of the hardware was financially supported by the European Commission (EC) within the Euro-Quebec Hydro-Hydrogen Pilot Project. The demonstration phase was financially supported by EC and the Bavarian State Government. Ludwig-Boelkow-Systemtechnik performed project monitoring for both funding organizations. The presentation will summarize the most important results of this demonstration phase and will address the measures undertaken in order to get the bus, the refueling infrastructure and the maintenance and operating procedures approved by the relevant authorities.

Process for the exchange of hydrogen isotopes between streams of liquid water and gaseous halohydrocarbon and an apparatus therefor

International Nuclear Information System (INIS)

Symons, E. A.; Clermont, M. J.; Paterson, L. M.; Rolston, J. H.

1985-01-01

Hydrogen isotope (e.g. deuterium) exchange from liquid water to a gaseous halohydrocarbon (e.g. fluoroform, CF 3 H-CF 3 D) is obtained at an operating temperature in the range 0 0 to 100 0 C. using a catalytically active mass comprising a porous anion exchange resin in the hydroxide ion form and enriched gaseous halohydrocarbon stream is decomposed by isotope selective photo-decomposition into a first, gaseous stream enriched in the hydrogen isotope, which is removed as a product, and a depleted gaseous halohydrocarbon stream, which is recirculated for enrichment again. The catalytically active mass may, for example, be in the form of resin particles suspended in a fluidized bed or packed as resin particles between sheets wound into a roll. One of the sheets may be corrugated and have open interstices to form a packing in a column which permits countercurrent gas and liquid flow past the resin. Preferably the wound sheets are hydrophilic to retard flooding by the liquid water. The liquid water stream may contain dimethyl sulfoxide (DMSO) added as co-solvent

Liquid metal purification device

International Nuclear Information System (INIS)

Sakai, Takao; Shimoyashiki, Shigehiro.

1992-01-01

The device of the present invention concerns a liquid metal purification device for removing and purifying impuries in liquid metal sodium used as coolants of an FBR type reactor. A vessel having a group of pipes made of hydrogen permeable metal at the inside thereof is disposed to the inlet pipeline of a cold trap. The group of hydrogen permeable metal pipes is connected to an exhaust pipe and a vacuum pump, so that the inside of the pipes is exhausted. Liquid metal sodium branched from the main pipeline of a coolant system passes through the outer side of the group of the hydrogen permeable metal pipes. In this cae, hydrogen contained as impurities in the liquid metal sodium diffuses and permeates the hydrogen permeation metal pipes and enters into the pipe group and is discharged out of the system by the vacuum pump. This can mitigate the hydrogen removing burden of the cold trap, to extend the device life time. (I.N.)

Hydrogen and carbon vapour pressure isotope effects in liquid fluoroform studied by density functional theory

Energy Technology Data Exchange (ETDEWEB)

Oi, Takao; Mitome, Ryota; Yanase, Satoshi [Sophia Univ., Tokyo (Japan). Faculty of Science and Technology

2017-06-01

H/D and {sup 12}C/{sup 13}C vapour pressure isotope effects (VPIEs) in liquid fluoroform (CHF{sub 3}) were studied at the MPW1PW91/6-31 ++ G(d) level of theory. The CHF{sub 3} monomer and CHF{sub 3} molecules surrounded by other CHF{sub 3} molecules in every direction in CHF{sub 3} clusters were used as model molecules of vapour and liquid CHF{sub 3}. Although experimental results in which the vapour pressure of liquid {sup 12}CHF{sub 3} is higher than that of liquid {sup 12}CDF{sub 3} and the vapour pressure of liquid {sup 13}CHF{sub 3} is higher than that of liquid {sup 12}CHF{sub 3} between 125 and 212 K were qualitatively reproduced, the present calculations overestimated the H/D VPIE and underestimated the {sup 12}C/{sup 13}C VPIE. Temperature-dependent intermolecular interactions between hydrogen and fluorine atoms of neighbouring molecules were required to explain the temperature dependences of both H/D and {sup 12}C/{sup 13}C VPIEs.

Adsorption methods for hydrogen isotope storage on zeolite sieves

International Nuclear Information System (INIS)

Cristescu, Ioana; Cristescu, Ion; Vasut, Felicia; Brad, Sebastian; Lazar, Alin

2001-01-01

Adsorption molecular sieves and activated carbon were used for hydrogen isotopes. The adsorption process proceeds at liquid nitrogen and liquid hydrogen temperatures. The synthetic zeolites have similar properties as natural zeolites, but they have a regular pore structure and affinity for molecules of different size with defined shapes. Experimental results obtained at liquid nitrogen and liquid hydrogen temperatures evidenced the efficient behavior of the activated carbon and zeolite sieves for hydrogen isotope temporary storage. (authors)

First experiment on liquid hydrogen transportation by ship inside Osaka bay

Science.gov (United States)

Maekawa, K.; Takeda, M.; Hamaura, T.; Suzuki, K.; Miyake, Y.; Matsuno, Y.; Fujikawa, S.; Kumakura, H.

2017-12-01

A project to import a large amount of liquid hydrogen (LH2) from Australia by a cargo carrier, which is equipped with two 1250 m3 tanks, is underway in Japan. It is important to understand sloshing and boil-off characteristics inside the LH2 tank during marine transportation. However, the LH2 sloshing and boil-off characteristics on the sea have not yet been clarified. First experiment on the LH2 transportation of 20 liter with magnesium diboride (MgB2) level sensors by the training ship “Fukae-maru”, which has 50 m long and 449 ton gross weight, was carried out successfully inside Osaka bay on February 2, 2017. In the experiment, synchronous measurements of liquid level, temperature, pressure, ship motions, and accelerations as well as the rapid depressurization test were done. The increase rate of the temperature and the pressure inside the LH2 tank were discussed under the rolling and the pitching conditions.

Functional organic materials based on polymerized liquid-crystal monomers: supramolecular hydrogen-bonded systems.

Science.gov (United States)

Broer, Dirk J; Bastiaansen, Cees M W; Debije, Michael G; Schenning, Albertus P H J

2012-07-16

Functional organic materials are of great interest for a variety of applications. To obtain precise functional properties, well-defined hierarchically ordered supramolecular materials are crucial. The self-assembly of liquid crystals has proven to be an extremely useful tool in the development of well-defined nanostructured materials. We have chosen the illustrative example of photopolymerizable hydrogen-bonding mesogens to show that a wide variety of functional materials can be made from a relatively simple set of building blocks. Upon mixing these compounds with other reactive mesogens, nematic, chiral nematic, and smectic or columnar liquid-crystalline phases can be formed that can be applied as actuators, sensors and responsive reflectors, and nanoporous membranes, respectively. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Key study on the potential of hydrazine bisborane for solid- and liquid-state chemical hydrogen storage.

Science.gov (United States)

Pylypko, Sergii; Petit, Eddy; Yot, Pascal G; Salles, Fabrice; Cretin, Marc; Miele, Philippe; Demirci, Umit B

2015-05-04

Hydrazine bisborane N2H4(BH3)2 (HBB; 16.8 wt %) recently re-emerged as a potential hydrogen storage material. However, such potential is controversial: HBB was seen as a hazardous compound up to 2010, but now it would be suitable for hydrogen storage. In this context, we focused on fundamentals of HBB because they are missing in the literature and should help to shed light on its effective potential while taking into consideration any risk. Experimental/computational methods were used to get a complete characterization data sheet, including, e.g., XRD, NMR, FTIR, Raman, TGA, and DSC. From the reported results and discussion, it is concluded that HBB has potential in the field of chemical hydrogen storage given that both thermolytic and hydrolytic dehydrogenations were analyzed. In solid-state chemical hydrogen storage, it cannot be used in the pristine state (risk of explosion during dehydrogenation) but can be used for the synthesis of derivatives with improved dehydrogenation properties. In liquid-state chemical hydrogen storage, it can be studied for room-temperature dehydrogenation, but this requires the development of an active and selective metal-based catalyst. HBB is a thus a candidate for chemical hydrogen storage.

The PRESPEC liquid-hydrogen target for in-beam gamma spectroscopy of exotic nuclei at GSI

International Nuclear Information System (INIS)

Louchart, C.; Gheller, J.M.; Chesny, Ph.; Authelet, G.; Rousse, J.Y.; Obertelli, A.; Boutachkov, P.; Pietri, S.; Ameil, F.; Audirac, L.; Corsi, A.; Dombradi, Z.; Gerl, J.; Gillibert, A.; Korten, W.; Mailleret, C.; Merchan, E.; Nociforo, C.; Pietralla, N.; Ralet, D.

2014-01-01

We report on a new liquid hydrogen and deuterium target dedicated to in-beam γ spectroscopy experiments in inverse kinematics at relativistic incident energies at GSI/FAIR. Target thicknesses from 10 to 80 mm can be achieved for an effective diameter of 60 mm. The target-cell and entrance window are maded of 200μm thick Mylar. The design has the advantage of being free of absorbing material at forward angles and 90°, allowing the detection of photons in a wide angular range. A commissioning experiment with a 54 Cr beam at 130 MeV/nucleon has been performed at GSI, using the Rare Isotopes INvestigation at GSI (RISING) detectors. The target has been shown to behave as expected and is ready for experiments at fragmentation Radioactive-Ion Beam Facilities. -- Highlights: • We report on a new liquid hydrogen target for gamma spectroscopy experiments at FAIR. • A commissioning experiment has been performed at GSI, using the RISING detectors. • The target behaves as expected and is ready for experiments

The Liquid Metallic Hydrogen Model of the Sun and the Solar Atmosphere VII. Further Insights into the Chromosphere and Corona

Directory of Open Access Journals (Sweden)

Robitaille P.-M.

2013-07-01

Full Text Available In the liquid metallic hydrogen model of the Sun, the chromosphere is responsible for the capture of atomic hydrogen in the solar atmosphere and its eventual re-entry onto the photospheric surface (P.M. Robitaille. The Liquid Metallic Hydrogen Model of the Sun and the Solar Atmosphere IV. On the Nature of the Chromosphere. Prog. Phys., 2013, v. 3, L15–L21. As for the corona, it represents a diffuse region containing both gaseous plasma and condensed matter with elevated electron affinity (P.M. Robitaille. The Liquid Metallic Hydrogen Model of the Sun and the Solar Atmosphere V. On the Nature of the Corona. Prog. Phys., 2013, v. 3, L22–L25. Metallic hydrogen in the corona is thought to enable the continual harvest of electrons from the outer reaches of the Sun, thereby preserving the neutrality of the solar body. The rigid rotation of the corona is offered as the thirty-third line of evidence that the Sun is comprised of condensed matter. Within the context of the gaseous models of the Sun, a 100 km thick transition zone has been hypothesized to exist wherein temperatures increase dramatically from 104–106 K. Such extreme transitional temperatures are not reasonable given the trivial physical scale of the proposed transition zone, a region adopted to account for the ultra-violet emission lines of ions such as C IV, O IV, and Si IV. In this work, it will be argued that the transition zone does not exist. Rather, the intermediate ionization states observed in the solar atmosphere should be viewed as the result of the simultaneous transfer of protons and electrons onto condensed hydrogen structures, CHS. Line emissions from ions such as C IV, O IV, and Si IV are likely to be the result of condensation reactions, manifesting the involvement of species such as CH4, SiH4, H3O+ in the synthesis of CHS in the chromosphere. In addition, given the presence of a true solar surface at the level of the photosphere in the liquid metallic hydrogen model

Thermal hydraulic tests of a liquid hydrogen cold neutron source. NISTIR 5026

International Nuclear Information System (INIS)

Siegwarth, J.D.; Olson, D.A.; Lewis, M.A.; Rowe, J.M.; Williams, R.E.; Kopetka, P.

1995-01-01

Liquid hydrogen cold neutron source designed at NBSR contains neutron moderator chamber. The NIST-B electrically heated glass moderator chamber used to test the NBSR chamber testing showed the following results: Stable operation possible up to at least 2200 watts with two-phase flow; LH 2 mass quickly reaches new, stable value after heat load change; Void fraction well below 20 at anticipated power and pressure; Restart of H 2 flow verified after extending supply line; Visual inspection showed no dryout or unexpected voids

Liquid Hydrogen Propellant Tank Sub-Surface Pressurization with Gaseous Helium

Science.gov (United States)

Stephens, J. R.; Cartagena, W.

2015-01-01

A series of tests were conducted to evaluate the performance of a propellant tank pressurization system with the pressurant diffuser intentionally submerged beneath the surface of the liquid. Propellant tanks and pressurization systems are typically designed with the diffuser positioned to apply pressurant gas directly into the tank ullage space when the liquid propellant is settled. Space vehicles, and potentially propellant depots, may need to conduct tank pressurization operations in micro-gravity environments where the exact location of the liquid relative to the diffuser is not well understood. If the diffuser is positioned to supply pressurant gas directly to the tank ullage space when the propellant is settled, then it may become partially or completely submerged when the liquid becomes unsettled in a microgravity environment. In such case, the pressurization system performance will be adversely affected requiring additional pressurant mass and longer pressurization times. This series of tests compares and evaluates pressurization system performance using the conventional method of supplying pressurant gas directly to the propellant tank ullage, and then supplying pressurant gas beneath the liquid surface. The pressurization tests were conducted on the Engineering Development Unit (EDU) located at Test Stand 300 at NASA Marshall Space Flight Center (MSFC). EDU is a ground based Cryogenic Fluid Management (CFM) test article supported by Glenn Research Center (GRC) and MSFC. A 150 ft3 propellant tank was filled with liquid hydrogen (LH2). The pressurization system used regulated ambient helium (GHe) as a pressurant, a variable position valve to maintain flow rate, and two identical independent pressurant diffusers. The ullage diffuser was located in the forward end of the tank and was completely exposed to the tank ullage. The submerged diffuser was located in the aft end of the tank and was completely submerged when the tank liquid level was 10% or greater

Handheld hydrogen - a new concept for hydrogen storage

DEFF Research Database (Denmark)

Johannessen, Tue; Sørensen, Rasmus Zink

2005-01-01

A method of hydrogen storage using metal ammine complexes in combination with an ammonia decomposition catalyst is presented. This dense hydrogen storage material has high degree of safety compared to all the other available alternatives. This technology reduces the safety hazards of using liquid...

Hydrogen activities in the European Union work-programme; Activites liees a l'hydrogene dans le programme de travail de l'Union Europeenne

Energy Technology Data Exchange (ETDEWEB)

Bahbout, A.; Tartaglia, G.P. [Joint Research Centre, IHCP, Ispra (Italy)

2000-07-01

Growing concern over urban air pollution, global climatic change allegedly caused by rising levels of greenhouse gases and future energy security requirements demand a solution: a clean and sustainable energy supply. Hydrogen is seen as a promising clean fuel when integrated into a wide and long-term vision in which it provides, in parallel with electricity, a secondary energy carrier, ultimately derived from renewable energy sources. Europe has been a pioneer in promoting the wider use of hydrogen. Already in 1991, various demonstration projects were started with funds under the Euro-Quebec Hydro-Hydrogen Pilot Project (EQHPP). The European Commission, the European Industry, the Government of Quebec and the Canadian Industry made resources available so that hydrogen, from surplus in Canada, could be applied in various end-use technologies. Under this project, about thirty European industry/research centres/universities have been involved, working on a comprehensive set of hydrogen applications/uses. Innovative public transportation means (city buses, boats) equipped with internal combustion engines (ICE) or fuel cells and using either liquid or compressed hydrogen were put into demonstration service. Cogeneration (CHP) projects based on the use of phosphoric acid fuel cells (PAFC) were realised. In joint programs, aviation combustor test activities were carried out by Daimler Benz Aerospace, Airbus Industries and Pratt and Whitney. Investigation of hydrogen storage in zeolites, carbon and nano-tubes were started. Tests on compressed hydrogen gas storage tanks were also conducted. All these projects are now terminated. As intended, the initial momentum set by the EQHPP project has now been replaced by many private initiatives, especially in Germany. Only one specific project funded by the European Commission, the European Integrated Hydrogen Project (EIHP) remains. In the EIHP project, several companies which designed and constructed prototypes and demonstration

Annular Air Leaks in a liquid hydrogen storage tank

Science.gov (United States)

Krenn, AG; Youngquist, RC; Starr, SO

2017-12-01

Large liquid hydrogen (LH2) storage tanks are vital infrastructure for NASA, the DOD, and industrial users. Over time, air may leak into the evacuated, perlite filled annular region of these tanks. Once inside, the extremely low temperatures will cause most of the air to freeze. If a significant mass of air is allowed to accumulate, severe damage can result from nominal draining operations. Collection of liquid air on the outer shell may chill it below its ductility range, resulting in fracture. Testing and analysis to quantify the thermal conductivity of perlite that has nitrogen frozen into its interstitial spaces and to determine the void fraction of frozen nitrogen within a perlite/frozen nitrogen mixture is presented. General equations to evaluate methods for removing frozen air, while avoiding fracture, are developed. A hypothetical leak is imposed on an existing tank geometry and a full analysis of that leak is detailed. This analysis includes a thermal model of the tank and a time-to-failure calculation. Approaches to safely remove the frozen air are analyzed, leading to the conclusion that the most feasible approach is to allow the frozen air to melt and to use a water stream to prevent the outer shell from chilling.

Caution on the use of liquid nitrogen traps in stable hydrogen isotope-ratio mass spectrometry

Science.gov (United States)

Coplen, Tyler B.; Qi, Haiping

2010-01-01

An anomalous stable hydrogen isotopic fractionation of 4 ‰ in gaseous hydrogen has been correlated with the process of adding liquid nitrogen (LN2) to top off the dewar of a stainless-steel water trap on a gaseous hydrogen-water platinum equilibration system. Although the cause of this isotopic fractionation is unknown, its effect can be mitigated by (1) increasing the capacity of any dewars so that they do not need to be filled during a daily analytic run, (2) interspersing isotopic reference waters among unknowns, and (3) applying a linear drift correction and linear normalization to isotopic results with a program such as Laboratory Information Management System (LIMS) for Light Stable Isotopes. With adoption of the above guidelines, measurement uncertainty can be substantially improved. For example, the long-term (months to years) δ2H reproducibility (1& sigma; standard deviation) of nine local isotopic reference waters analyzed daily improved substantially from about 1‰ to 0.58 ‰. This isotopically fractionating mechanism might affect other isotope-ratio mass spectrometers in which LN2 is used as a moisture trap for gaseous hydrogen

Carbon: Hydrogen carrier or disappearing skeleton?

International Nuclear Information System (INIS)

De Jong, K.P.; Van Wechem, H.M.H.

1994-01-01

The use of liquid hydrocarbons as energy carriers implies the use of carbon as a carrier for hydrogen to facilitate hydrogen transport and storage. The current trend for liquid energy carriers used in the transport sector is to maximize the load of hydrogen on the carbon carrier. The recently developed Shell Middle Distillate Hydrogenation process for the manufacture of high quality diesel from aromatic refinery streams fits this picture. In the future, the hydrogen required to raise the product H/C ratio will be increasingly produced via gasification of large amounts of heavy residues. In the light of the strong preference towards using liquid fuels in the transport sector, the Shell Middle Distillate Synthesis process to convert natural gas into diesel of very high quality is discussed. Finally, a few comments on the use of hydrogen without a carbon carrier are made. Long lead times and the likelihood of producing the 'first' hydrogen from fossil fuel are highlighted. 13 figs., 6 tabs., 5 refs

Comment on "Protonium annihilation into $\\pi^{0} \\pi^{0}$ at rest in a liquid hydrogen target"

CERN Document Server

Amsler, Claude; Barnett, B M; Batty, C J; Benayoun, M; Blüm, P; Braune, K; Bugg, D V; Case, T; Credé, V; Crowe, K M; Doser, Michael; Dünnweber, W; Engelhardt, D; Faessler, M A; Haddock, R P; Heinsius, F H; Heinzelmann, M; Hessey, N P; Hidas, P; Jamnik, D; Kalinowsky, H; Kammel, P; Kisiel, J; Klempt, E; Koch, H; Kunze, M; Kurilla, U; Landua, Rolf; Matthäy, H; Meyer, C A; Meyer-Wildhagen, F; Ouared, R; Peters, K; Pick, B; Ratajczak, M; Regenfus, C; Reinnarth, J; Röthel, W; Sarantsev, A V; Spanier, S; Strohbusch, U; Suffert, Martin; Suh, J S; Thoma, U; Uman, I; Wallis-Plachner, S; Walther, D; Wiedner, U; Wittmack, K; Zou, B S

2002-01-01

We comment on the recent paper published by the Obelix Collaboration on protonium annihilation into pi /sup 0/ pi /sup 0/ at rest in a liquid hydrogen target ÝPhys. Rev. D 65, 012001 (2002)¿, with particular reference to the discrepancy with the results obtained by the Crystal Barrel Collaboration.

Liquid Metallic Hydrogen II. A Critical Assessment of Current and Primordial Helium Levels in the Sun

Directory of Open Access Journals (Sweden)

Robitaille P.-M.

2013-04-01

Full Text Available Before a solar model becomes viable in astrophysics, one mus t consider how the ele- mental constitution of the Sun was ascertained, especially relative to its principle com- ponents: hydrogen and helium. Liquid metallic hydrogen has been proposed as a solar structural material for models based on condensed matter (e .g. Robitaille P.-M. Liq- uid Metallic Hydrogen: A Building Block for the Liquid Sun. Progr. Phys. , 2011, v. 3, 60–74. There can be little doubt that hydrogen plays a d ominant role in the uni- verse and in the stars; the massive abundance of hydrogen in t he Sun was established long ago. Today, it can be demonstrated that the near isointe nse nature of the Sun’s Balmer lines provides strong confirmatory evidence for a dis tinct solar surface. The situation relative to helium remains less conclusive. Stil l, helium occupies a prominent role in astronomy, both as an element associated with cosmol ogy and as a byproduct of nuclear energy generation, though its abundances within the Sun cannot be reliably estimated using theoretical approaches. With respect to th e determination of helium lev- els, the element remains spectroscopically silent at the le vel of the photosphere. While helium can be monitored with ease in the chromosphere and the prominences of the corona using spectroscopic methods, these measures are hig hly variable and responsive to elevated solar activity and nuclear fragmentation. Dire ct assays of the solar winds are currently viewed as incapable of providing definitive in formation regarding solar helium abundances. As a result, insight relative to helium r emains strictly based on the- oretical estimates which couple helioseismological appro aches to metrics derived from solar models. Despite their “state of the art” nature, heliu m estimates based on solar models and helioseismology are suspect on several fronts, i ncluding their reliance on solar opacities. The best knowledge can only come from the so

The formation of nitrogeneous compounds in the γ-radiolyses of liquid nitrogen solutions of hydrogen, methane, and ethane

International Nuclear Information System (INIS)

Horigome, Keiichi; Hirokami, Shun-ichi; Sato, Shin

1978-01-01

The γ-radiolyses of liquid nitrogen solutions of hydrogen, methane, and ethane have been reinvestigated. A complete survey of nitrogen-containing products has been attempted. The nitrogeneous compounds observed were ammonia (0.7) and hydrogen azide (0.02) in the case of hydrogen, ammonia (0.3), hydrogen cyanide (0.1), methyl azide (0.01), and a polymer in the case of methane, and ammonia (0.3), hydrogen cyanide (0.05), acetonitrile (0.04), ethyl azide (0.01), and a polymer in the case of ethane. The values in parentheses are the G-values obtained at optimum conditions. The hydrolysis of the polymer obtained with methane gave formaldehyde in amounts which correspond to the fact that the G-value of the nitrogen atoms which were converted into the polymer is about 1.0. In order to explain these results, possible reaction mechanisms are discussed. (auth.)

Fermentative hydrogen production from liquid swine manure with glucose supplement using an anaerobic sequencing batch reactor

Science.gov (United States)

Wu, Xiao

2009-12-01

The idea of coupling renewable energy production and agricultural waste management inspired this thesis. The production of an important future fuel---hydrogen gas---from high strength waste stream-liquid swine manure---using anaerobic treatment processes makes the most sustainable sense for both wastewater utilization and energy generation. The objectives of this thesis were to develop a fermentation process for converting liquid swine manure to hydrogen and to maximize hydrogen productivity. Anaerobic sequencing batch reactor (ASBR) systems were constructed to carry out this fermentation process, and seed sludge obtained from a dairy manure anaerobic digester and pretreated by nutrient acclimation, heat and pH treatment was used as inoculum. High system stability was indicated by a short startup period of 12 days followed by stable hydrogen production, and successful sludge granulation occurred within 23 days of startup at a hydraulic retention time (HRT) of 24 hours. Operation at a progressively decreasing HRT from 24 to 8h gave rise to an increasing biogas production rate from 15.2-34.4L/d, while good linear relationships were observed between both total biogas and hydrogen production rates correlated to HRT, with R2 values of 0.993 and 0.997, respectively. The maximum hydrogen yield of 1.63 mol-H 2/mol-hexose-feed occurred at HRT of 16h, while the HRT of 12h was highly suggested to achieve both high production rate and efficient yield. Hexose utilization efficiencies over 98%, considerable hydrogen production rate up to 14.3 L/d and hydrogen percentage of off-gas up to 43% (i.e., a CO 2/H2 ratio of 1.2) with the absence of CH4 production throughout the whole course of experiment at a pH of 5.0 strongly validated the feasibility of the fermentative H2 production from liquid swine manure using an ASBR system. Ethanol as well as acetic, butyric and valeric acids were produced in the system accompanying the hydrogen production, with acetic acid being the dominant

Hydrogenation of nitriles on a well-characterized nickel surface: From surface science studies to liquid phase catalytic activity measurements

Energy Technology Data Exchange (ETDEWEB)

Gardin, Denis Emmanuel [Univ. of California, Berkeley, CA (United States)

1993-12-01

Nitrile hydrogenation is the most commonly used method for preparing diverse amines. This thesis is aimed at the mechanism and factors affecting the performance of Ni-based catalysts in nitrile hydrogenations. Surface science techniques are used to study bonding of nitriles and amines to a Ni(111) surface and to identify surface intermediates. Liquid-phase hydrogenations of cyclohexene and 1-hexene on a Pt foil were carried out successfully. Finally, knowledge about the surface structure, surface chemical bond, dynamics of surface atoms (diffusion, growth), and reactivity of metal surfaces from solid-gas interface studies, is discussed.

Intensification of the Use of Ionic Liquids as Efficient Reaction Co-Solvents in Asymmetric Hydrogenations

Czech Academy of Sciences Publication Activity Database

Černá, I.; Klusoň, Petr; Bendová, Magdalena; Floriš, Tomáš; Pelantová, Helena; Pekárek, T.

2011-01-01

Roč. 50, č. 3 (2011), s. 264-272 ISSN 0255-2701 R&D Projects: GA AV ČR KAN400720701; GA AV ČR IAA400720710 Institutional research plan: CEZ:AV0Z40720504; CEZ:AV0Z50200510 Keywords : Ionic liquids * asymmetric hydrogenations * BmimPF6 Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.924, year: 2011

Induced Smectic X Phase Through Intermolecular Hydrogen-Bonded Liquid Crystals Formed Between Citric Acid and p- n-(Octyloxy)Benzoic Acid

Science.gov (United States)

Sundaram, S.; Subhasri, P.; Rajasekaran, T. R.; Jayaprakasam, R.; Senthil, T. S.; Vijayakumar, V. N.

2017-08-01

Hydrogen-bonded liquid crystal (HBLC) is synthesized from citric acid (CA) and 4-(octyloxy)benzoic acid (8OBA) with different mole ratios. Fourier transform infrared spectroscopy (FT-IR) confirms the presence of hydrogen bond between CA and 8OBA. Nuclear magnetic resonance (NMR) spectroscopic studies validate the intermolecular complementary, cyclic type of hydrogen bond, and molecular environment in the designed HBLC complex. Powder X-ray diffraction analysis reveals the monoclinic nature of liquid crystal complex in solid phase. Liquid crystal parameters such as phase transition temperature and enthalpy values for the corresponding mesogenic phases are investigated using a polarizing optical microscope (POM) and differential scanning calorimetry (DSC). It is observed that the change in chain length and steric hindrance while increasing the mole ratio in HBLC complex induces a new smectic X (Sm X) along with higher-order smectic G (Sm G) phases by quenching of smectic C (Sm C). From the experimental observations, induced Sm X phase has been identified as a finger print texture. Also, Sm G is a multi-colored mosaic texture in 1:1, 1:2, and 1:3 mol ratios. The optical tilt angle, thermal stability factor, and enhanced thermal span width of CA + 8OBA complex are discussed.

KOMPOSISI DAN AKTIVITAS ANTIBAKTERI ASAP CAIR SABUT KELAPA YANG DIBUAT DENGAN TEKNIK PEMBAKARAN NON PIROLISIS Composition and Antibacterial Activity of Liquid Smoke of Coconut Fiber Made by NonPirolisis Combusting Technique

Directory of Open Access Journals (Sweden)

Feti Fatimah

2012-05-01

Full Text Available Food preservation by liquid smoke was one of the food conservation techniques that was easy to be conducted.Nonetheless, it was difficult in reality for people to product liquid smoke because of the complicated process in making pirolisis tools. This study was conducted to learn how to make liquid smoke by non pirolisis technique using the basic material of coconut fiber. And then, it must be performed in the liquid smoke, the redistilation and the adsorption process using active carbon. The quality of liquid smoke was examined by observing the components using Gas chromatography-Mass Spectrophotometry (GC-MS and performing test of antibacterial activity to three kinds of bacterias: Salmonella choleraeaeus, Bacillus subtilus, and Staphylococcus aureus using technic of well in the PCA media of 108/ml in population. Based on the study results, it was found that the original liquid smoke (without redistilation and adsorption process using active carbon consisted at least of 21 components, redistilated liquid smoke consist at least of 31 components, and adsorpted liquid smoke using active carbon consisted at least of 5 components. From the result of test of antibacterial activity, it was found that the redistilated liquid smoke showed better bacterial activity than in the original liquid smoke, whereas the absorpted liquid smoke using active carbon had the smallest activity among them. It was because of the content of the 2-methoxiphenol compound in the redistilated liquid smoke was the highest among them. And based on this phenomena, it was found that redistilation technique could increase the quality of liquid smoke of coconut fiber made by non pirolisis combusting method. ABSTRAK Pengawetan menggunakan asap cair merupakan salah satu teknik pengawetan bahan pangan yang mudah diaplikasikan.Meskipun demikian, pada kenyataannya, masyarakat kesulitan memproduksi asap cair dikarenakan sulitnya membuat peralatan pirolisis. Penelitian ini dilakukan guna

Critical Current Test of Liquid Hydrogen Cooled HTC Superconductors under External Magnetic Field

OpenAIRE

Shirai, Yasuyuki; Shiotsu, Masahiro; Tatsumoto, Hideki; Kobayashi, Hiroaki; Naruo, Yoshihiro; Nonaka, Satoshi; Inatani, Yoshifumi

2016-01-01

High-Tc (HTC) superconductors including MgB2 will show excellent properties under temperature of Liquid Hydrogen (LH2:20K), which has large latent heat and low viscosity coefficient. In order to design and fabricate the LH2 cooled superconducting energy devices, we must clear the cooling property of LH2 for superconductors, the cooling system and safety design of LH2 cooled superconducting devices and electro-magnetic property evaluation of superconductors (BSCCO, REBCO and MgB2) and their ma...

Design of a reconfigurable liquid hydrogen fuel tank for use in the Genii unmanned aerial vehicle

International Nuclear Information System (INIS)

Adam, Patrick; Leachman, Jacob

2014-01-01

Long endurance flight, on the order of days, is a leading flight performance characteristic for Unmanned Aerial Vehicles (UAVs). Liquid hydrogen (LH2) is well suited to providing multi-day flight times with a specific energy 2.8 times that of conventional kerosene based fuels. However, no such system of LH2 storage, delivery, and use is currently available for commercial UAVs. In this paper, we develop a light weight LH2 dewar for integration and testing in the proton exchange membrane (PEM) fuel cell powered, student designed and constructed, Genii UAV. The fuel tank design is general for scaling to suit various UAV platforms. A cylindrical vacuum-jacketed design with removable end caps was chosen to incorporate various fuel level gauging, pressurizing, and slosh mitigation systems. Heat and mechanical loadings were modeled to compare with experimental results. Mass performance of the fuel tank is characterized by the fraction of liquid hydrogen to full tank mass, and the insulation performance was characterized by effective thermal conductivity and boil-off rate

Design of a reconfigurable liquid hydrogen fuel tank for use in the Genii unmanned aerial vehicle

Energy Technology Data Exchange (ETDEWEB)

Adam, Patrick; Leachman, Jacob [HYdrogen Properties for Energy Research (HYPER) Laboratory, Washington State University, Pullman, WA 99164-2920 (United States)

2014-01-29

Long endurance flight, on the order of days, is a leading flight performance characteristic for Unmanned Aerial Vehicles (UAVs). Liquid hydrogen (LH2) is well suited to providing multi-day flight times with a specific energy 2.8 times that of conventional kerosene based fuels. However, no such system of LH2 storage, delivery, and use is currently available for commercial UAVs. In this paper, we develop a light weight LH2 dewar for integration and testing in the proton exchange membrane (PEM) fuel cell powered, student designed and constructed, Genii UAV. The fuel tank design is general for scaling to suit various UAV platforms. A cylindrical vacuum-jacketed design with removable end caps was chosen to incorporate various fuel level gauging, pressurizing, and slosh mitigation systems. Heat and mechanical loadings were modeled to compare with experimental results. Mass performance of the fuel tank is characterized by the fraction of liquid hydrogen to full tank mass, and the insulation performance was characterized by effective thermal conductivity and boil-off rate.

C1 CHEMISTRY FOR THE PRODUCTION OF ULTRA-CLEAN LIQUID TRANSPORTATION FUELS AND HYDROGEN

Energy Technology Data Exchange (ETDEWEB)

Gerald P. Huffman

2004-09-30

The Consortium for Fossil Fuel Science (CFFS) is a research consortium with participants from the University of Kentucky, University of Pittsburgh, West Virginia University, University of Utah, and Auburn University. The CFFS is conducting a research program to develop C1 chemistry technology for the production of clean transportation fuel from resources such as coal and natural gas, which are more plentiful domestically than petroleum. The processes under development will convert feedstocks containing one carbon atom per molecular unit into ultra clean liquid transportation fuels (gasoline, diesel, and jet fuel) and hydrogen, which many believe will be the transportation fuel of the future. Feedstocks include synthesis gas, a mixture of carbon monoxide and hydrogen produced by coal gasification, coalbed methane, light products produced by Fischer-Tropsch (FT) synthesis, methanol, and natural gas.

Viscoélasticité et diffusion dépolarisée de la lumière dans les liquides

Science.gov (United States)

Quentrec, B.

The spectra of the depolarized light scattering in the liquids are related to the viscoelastic properties of the medium, which in turn reflect the local order. Their interpretation requires a theory which generalizes hydrodynamics. In this paper are reviewed the different theories allowing this generalization independently of the fact they use the formalism of Zwanzig-Mori or the non-equilibrium thermodynamics. A special place is given to the theory developed by the author which appears as the most general one. The comparison with the experimental results confirms the necessity of such a complex theory. Les spectres de diffusion dépolarisée de la lumière dans les liquides sont liés aux propriétés viscoélastiques du milieu, qui reflètent à leur tour l'ordre local. Leur interprétation demande une théorie généralisant l'hydrodynamique. Dans cet article sont passées en revue les différentes théories permettant cette généralisation, qu'elles utilisent le formalisme de Zwanzig-Mori ou la thermodynamique hors d'équilibre. Une place à part est faite à celle développée par l'auteur qui apparaît comme la plus générale. La comparaison avec les résultats expérimentaux confirme la nécessité d'une théorie aussi complexe.

Characterization of the hydrogen bond in molecular systems of biological interest by neutron scattering; Caracterisation de la liaison hydrogene dans des systemes moleculaires d'interet biologique par diffusion de neutrons

Energy Technology Data Exchange (ETDEWEB)

Cavillon, F

2004-10-15

This work presents a methodology for the analysis of the scattering spectra of neutrons on molecular liquids. This method is based on the adjustment of the molecular form factor concerning great momentum transfer. The subtraction of the intra-molecular contributions gives access to information on inter-molecular interactions such as the hydrogen bond. 3 systems with increasing levels of difficulty have been studied: the ammonia molecule, the N-methyl-formamide (NMF) and the N-methyl-acetamide (NMA). The value we get for the N-D intermolecular distance of the liquid ammonia molecule is 1.7 angstrom, this value is different from the value generally admitted (2.3 angstrom) but we have validated it by studying the isotopic substitution N{sup 14}/N{sup 15}. The adjustment to the NMF is obtained with a good accuracy but the characterization of the hydrogen bound is more delicate to infer. A preliminary study of the NMA molecule shows that this method can give relevant results on complex molecules.

Generation of core–shell nanoparticles Al@Ti by laser ablation in liquid for hydrogen storage

Energy Technology Data Exchange (ETDEWEB)

Serkov, A.A. [Wave Research Center of A.M. Prokhorov General Physics Institute of the Russian Academy of Sciences, 38, Vavilov street, 119991 Moscow (Russian Federation); The Federal State Educational Institution of Higher Professional Education, “Moscow Institute of Physics and Technology (State University)”, 9, Institutsky lane, 141700, Dolgoprudny, Moscow (Russian Federation); Barmina, E.V.; Simakin, A.V. [Wave Research Center of A.M. Prokhorov General Physics Institute of the Russian Academy of Sciences, 38, Vavilov street, 119991 Moscow (Russian Federation); Kuzmin, P.G., E-mail: qzzzma@gmail.com [Wave Research Center of A.M. Prokhorov General Physics Institute of the Russian Academy of Sciences, 38, Vavilov street, 119991 Moscow (Russian Federation); Voronov, V.V. [A.M. Prokhorov General Physics Institute of the Russian Academy of Sciences, 38, Vavilov street, 119991 Moscow (Russian Federation); Shafeev, G.A. [Wave Research Center of A.M. Prokhorov General Physics Institute of the Russian Academy of Sciences, 38, Vavilov street, 119991 Moscow (Russian Federation); National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), 31, Kashirskoye highway, 115409 Moscow (Russian Federation)

2015-09-01

Highlights: • Core–shell Al@Ti NPs are generated by laser ablation in isopropanol. • Isopropanol was saturated with molecular hydrogen. • The composite metallic Al-Ti target was used. • HR TEM characterization shows that Ti core is covered by epitaxial Al shell. • Al@Ti NPs are promising for hydrogen storage. - Abstract: Core–shell Al@Ti nanoparticles are generated by ablation of a composite Ti–Al target in liquid isopropanol saturated with molecular hydrogen using a Nd:YAG laser with pulse duration of 10 ps and repetition rate of 200 kHz. The target is made of two plates of corresponding metals stacked together and placed into a flowing cell reactor. Transmission Electron Microscopy analysis of generated NPs reveals their core–shell structure with Ti core and Al shell. Average size of NPs determined by means of measuring disk centrifuge is around 40 nm. Saturation of NPs by hydrogen is due to sharp dependence of its solubility in these metals on temperature. XRD studies of generated NPs show the peaks of both metallic Ti and Al with some amount of TiO{sub 2}. No peaks of Ti–Al alloys are observed.

PEMANFAATAN SEREH (Cymbopogon Cytratus DALAM MENURUNKAN BAU PADA PUPUK ORGANIK CAIR DAN POTENSINYA DALAM MENINGKATKAN PRODUKSI TANAMAN CABAI (Capsicum Annum

Directory of Open Access Journals (Sweden)

Nurhasanah Nurhasanah

2013-09-01

Full Text Available Research in the use of lemongrass (Cymbopogon citratus to reduce odors in liquid organic fertilizer has been conducted in Bogor for 6 months. This study begin with a liquid organic fertilizer produced from 1 kg of shrimp waste, 1 kg of maize, 1 kg of bean sprouts, 10 liters of coconut water, 500 ml of EM4 and 500 g of sugar through fermentation process for 6 weeks. Then the result of liquid organic fertilizer was added by an ingredient lemongrass as deodorizing with doses of 0, 10%, 20% and 30% (w/v. After that it is fermented for 2 weeks. The next stage was the application of liquid organic fertilizer as a foliar fertilizer at chillies (Capsicum annum planting using a completely randomized design (CRD 1 factors type of using liquid organic fertilizer (control, liquid organic fertilizer without lemongrass, liquid organic fertilizer + 10% lemongrass, liquid organic fertilizer + 20% lemongrass and liquid organic fertilizer + 30% lemongrass respectively at doses of 0, 6, 12 and 18 ppm. The parameters measured were odor (NH3 and H2S, levels of macro nutrients (N, P, K, Ca, Mg, and S and micro nutrients (Cu, Zn, Mn, and Fe after fermenting process, and the production of crops (fruit number and fruit weight after planting. Research results show that the higher dose of lemongrass added cause levels of odor (NH3 and H2S in the liquid organic fertilizer decreased and content of macro nutrients, micro nutrients, and phytohormones increased. The planting results indicate liquid organic fertilizer which added 20% lemongrass in a dose of 12 ppm was the optimal dose in increasing crop production. Penelitian penggunaan sereh (Cymbopogon citratus dalam menurunkan bau pada pupuk organik cair telah dilakukan di Bogor selama 6 bulan. Penelitian ini diawali dengan membuat pupuk organik cair yang dihasilkan dari 1 kg limbah udang, 1 kg jagung, 1 kg touge, 10 Liter air kelapa, 500 ml EM4 dan 500 g gula pasir melalui proses fermentasi selama 6 minggu. Kemudian pada

Process for exchanging hydrogen isotopes between gaseous hydrogen and water

International Nuclear Information System (INIS)

Hindin, S.G.; Roberts, G.W.

1977-01-01

A process is described for exchanging isotopes (particularly tritium) between water and gaseous hydrogen. Isotope depleted gaseous hydrogen and water containing a hydrogen isotope are introduced into the vapour phase in a first reaction area. The steam and gaseous hydrogen are brought into contact with a supported metal catalyst in this area in a parallel flow at a temperature range of around 225 and 300 0 C. An effluent flow comprising a mixture of isotope enriched gaseous hydrogen and depleted steam is evacuated from this area and the steam condensed into liquid water [fr

Analysis of the effects of explosion of a hydrogen cylinder on the transfer of radioactive liquid wastes at nuclear power stations

International Nuclear Information System (INIS)

Lopes, Karina B.; Melo, Paulo Fernando F.F. e

2011-01-01

This work presents a study of explosion effects of a stored hydrogen cylinder on the transfer of radioactive liquid wastes at nuclear power plants. The peak overpressure is calculated, as well as the strength of resulting fragments, thus confirming the main harmful effect of an explosion of flammable vapor cloud, based on the TNT equivalent method. The scenarios identified are calculated and compared with the overpressure ranges of 1%, 50% and 99% of structural damages, which were determined by the Eisenberg's vulnerability model. The results show that the overpressure and the resulting fragments from the explosion of a hydrogen gas cylinder are not able to cause the overturning of the tanker under study, and also show that a minimum distance of 30 meters between the hydrogen cylinder and the tanker can be considered a safe distance to the passage of this tanker during the transfer of radioactive liquid waste, in which the likelihood of occurrence of structural damages is less than 1%. (author)

Potential of multi-purpose liquid metallic fuelled fast reactor (MPFR) as a hydrogen production system

International Nuclear Information System (INIS)

Endo, H.; Ninokata, H.; Netchaev, A.; Sawada, T.

2001-01-01

Nuclear energy is the only effective alternative energy source to fossil fuels in the next century. Therefore future nuclear power plants should satisfy the following three requirements: i) multiple energy conversion capability with high temperature not only for electricity generation but also for hydrogen production, ii) extended siting capability so as to eliminate on-site refuelling, and iii) passive safety features. An aim of this paper is to describe the basic concept of the multi-purpose liquid metallic fuelled fast reactor system (MPFR). The MPFR introduces the U-Pu-X (X: Mn, Fe, Co) liquid metallic alloy with Ta and Ta/TaC structural materials, and satisfies all of the conditions listed above based on the following characteristics of the liquid metallic fuel: high temperature operation between 650 deg C (sodium-cooled system) and 1 200 deg C (lead-cooled system), a core lifetime of 15-30 years without radiation damage of fuel materials, and enhanced passive safety by the thermal expansion of liquid fuel and the avoidance of re-criticality due to local core fuel dispersion at fuel failure events. (authors)

Pengaruh Fermentasi Fungi, Bakteri Asam Laktat dan Khamir terhadap Kualitas Nutrisi Tepung Sorgum

Directory of Open Access Journals (Sweden)

Raden Haryo Bimo Setiarto

2017-02-01

Full Text Available Recently, food security problem in Indonesia is mainly due to the consumption dependence on rice and wheat, while the utilization of local sources of carbohydrates such as tubers and cereals are still limited. Sorghum is one of local cereal that potential to be developed as source of carbohydrates and protein. However, a problem encountered on utilising sorghum as food is the low protein digestibility. The objective of this study was to investigate the effects of fermentation of Rhizopus oligosporus, Lactobacillus plantarum, and Saccharomyces cerevisiae on nutritional quality and digestibility of sorghum flour. The procedure in this research were pre-treatment of sorghum grains, preparations of inoculum, solid state fermentation, liquid state fermentation, mixture solid-liquid fermentation of sorghum grains, flouring (draining and mashing, microbial (total plate count and chemical analysis (proximate analysis, amino acid analysis, and protein digestibilty. Sorghum flour was made with 4 variations of treatments that was performed in triplo, i.e: control (without fermentation, liquid fermentation (with Lactobacillus plantarum and Saccharomyces cerevisiae, solid fermentation (with Rhizopus oligosporus, solid and liquid fermentation (with addition of Rhizopus oligosporus,Lactobacillus plantarum and Saccharomyces cerevisiae. The result showed that the number of microbes in fermented sorghum flour was still within the safety limits in accordance to SNI. The fermentation process did not significantly influence the levels of protein, carbohydrate, and fat of sorghum flour. During the fermentation of sorghum, the levels of the amino acids cysteine and lysine increased while several other amino acids decreased. Fermentation increased significantly the digestibility of sorghum protein up to 3,5-5 fold than control without fermentation. ABSTRAK Masalah ketahanan pangan di Indonesia saat ini diantaranya adalah pola konsumsi masyarakat sangat tergantung pada

An advanced liquid hydrogen cold source for the NIST research reactor

International Nuclear Information System (INIS)

Williams, R.E.; Kopetka, P.; Rowe, J.M.

1999-01-01

A second-generation liquid hydrogen cold neutron source is currently being fabricated and will be installed in the NIST reactor early next year. The existing source has operated very successfully over the last four years, providing a six-fold increase in the cold neutron yield compared to the previous heavy ice source. The design of the new source is based on our operating experience with the existing LH 2 source and extensive neutron transport calculations using improved MCNP modeling and computational capabilities. Enhanced mechanical design and manufacturing tools are exploited in the fabrication of the advanced source, which is expected to nearly double the yield of the existing LH 2 source. (author)

Electronic transport coefficients from ab initio simulations and application to dense liquid hydrogen

International Nuclear Information System (INIS)

Holst, Bastian; French, Martin; Redmer, Ronald

2011-01-01

Using Kubo's linear response theory, we derive expressions for the frequency-dependent electrical conductivity (Kubo-Greenwood formula), thermopower, and thermal conductivity in a strongly correlated electron system. These are evaluated within ab initio molecular dynamics simulations in order to study the thermoelectric transport coefficients in dense liquid hydrogen, especially near the nonmetal-to-metal transition region. We also observe significant deviations from the widely used Wiedemann-Franz law, which is strictly valid only for degenerate systems, and give an estimate for its valid scope of application toward lower densities.

PERBANDINGAN EFEKTIFITAS DISINFEKTAN KAPORIT, HIDROGEN PEROKSIDA, DAN PEREAKSI FENTON (H2O2/Fe2+

Directory of Open Access Journals (Sweden)

Didik Setiawan

2013-11-01

Full Text Available Tujuan dari penelitian ini adalah untuk menentukan konsentrasi optimum dan efektifitas hidrogen peroksida dan pereaksi Fenton sebagai disinfektan dibandingkan dengan kaporit. Efektivitas disinfeksi ditentukan berdasarkan beberapa parameter yaitu: koefisien fenol disinfektan dan kualitas air yang dihasilkan yang diukur melalui pH, oksigen terlarut (DO, dissolved oxygen, dan suhunya serta harga disinfektan itu sendiri. Analisis statistik ANOVA dua arah tanpa interaksi  pada tingkat kesalahan 0.01 dilakukan guna menentukan disinfektan paling efektif dan konsentrasi optimumnya. Uji koefisien fenol dilakukan dengan mencampurkan disinfektan dengan konsentrasi tertentu dengan bakteri Salmonella typhosa dan Staphyllococcus aureuskemudian membandingkan hasilnya dengan fenol.Hasil pengamatan menunjukkan bahwa koefisien fenol dari kaporit, hidrogen peroksida, dan reagen Fenton berturut-turut adalah 4, 6, dan 6. Air yang dihasilkan oleh kaporit mempunyai pH, DO dan suhu berturut-turut adalah 10.07 - 9.2, 6.63-8.07 mgL-1, dan 28.5-28.13oC. Air yang didisinfeksi dengan hidrogen peroksida mempunyai pH,DO, dan suhu berturut-turut adalah 9.03-7.33, 6.93-9.40 mgL-1  , dan 28.5-28.03oC. Sedangkan air hasil didisinfeksi dengan reagen Fenton mempunyai pH, DO, dan suhu berturut-turut adalah 5.97-4.57, 7.40-8.57 mgL-1 , dan 28.47-28.07oC.Meskipun kaporit paling murah, namun dari segi kesehatan hidrogen peroksida merupakan reagen yang paling aman dan paling efektif karena dengan daya disinfeksi enam kali dibandingkan fenol, tidak meninggalkan residu yang membahayakan. Fenton, dilain pihak, meskipun mempunyai daya disinfeksi setara dengan hidrogen peroksida, namun menghasilkan ion Besi (III dalam air sehingga memerlukan pengolahan lebih jauh.Dengan demikian, secara keseluruhan hidrogen peroksida merupakan disinfektan paling efektif dari ketiganya.   The purpose of this study is to determine the optimum concentration and the effectiveness of hydrogen peroxide and

Hydrogen fuel. Uses

International Nuclear Information System (INIS)

Darkrim-Lamari, F.; Malbrunot, P.

2006-01-01

Hydrogen is a very energetic fuel which can be used in combustion to generate heat and mechanical energy or which can be used to generate electricity and heat through an electrochemical reaction with oxygen. This article deals with the energy conversion, the availability and safety problems linked with the use of hydrogen, and with the socio-economical consequences of a generalized use of hydrogen: 1 - hydrogen energy conversion: hydrogen engines, aerospace applications, fuel cells (principle, different types, domains of application); 2 - hydrogen energy availability: transport and storage (gas pipelines, liquid hydrogen, adsorbed and absorbed hydrogen in solid materials), service stations; 3 - hazards and safety: flammability, explosibility, storage and transport safety, standards and regulations; 4 - hydrogen economy; 5 - conclusion. (J.S.)

Importance of international standards on hydrogen technologies

International Nuclear Information System (INIS)

Bose, T.K.; Gingras, S.

2001-01-01

This presentation provided some basic information regarding standards and the International Organization for Standardization (ISO). It also explained the importance of standardization activities, particularly ISO/TC 197 which applies to hydrogen technologies. Standards are established by consensus. They define the minimum requirements that will ensure that products and services are reliable and effective. Standards contribute to the elimination of technical barriers to trade (TBT). The harmonization of standards around the world is desirable in a free trade environment. The influence of the TBT on international standardization was discussed with particular reference to the objectives of ISO/TC 197 hydrogen technologies. One of the priorities for ISO/TC 197 is a hydrogen fuel infrastructure which includes refuelling stations, fuelling connectors, and storage technologies for gaseous and liquid hydrogen. Other priorities include an agreement between the International Electrotechnical Commission (IEC) and the ISO, in particular the IEC/TC 105 and ISO/TC 197 for the development of fuel cell standards. The international standards that have been published thus far include ISO 13984:1999 for liquid hydrogen, land vehicle fuelling system interface, and ISO 14687:1999 for hydrogen fuel product specification. Standards are currently under development for: liquid hydrogen; airport hydrogen fuelling facilities; gaseous hydrogen blends; basic considerations for the safety of hydrogen systems; gaseous hydrogen and hydrogen blends; and gaseous hydrogen for land vehicle filling connectors. It was concluded that the widespread use of hydrogen is dependent on international standardization

A new versatile facility: Vehicle-1 for innovative PFC concepts evaluation and its first experiments on hydrogen recycling from solid and liquid lithium

International Nuclear Information System (INIS)

Hirooka, Y.; Ohgaki, H.; Ohtsuka, Y.; Nishikawa, M.

2005-01-01

A new plasma facility: Vehicle-1 has been built for the evaluation of innovative plasma-facing component concepts. This facility can conduct experiments in such a way that standing liquids in a tray are exposed to vertically flowing plasmas, or that flowing liquids on a slope are bombarded with horizontally directed plasmas. Vehicle-1 can generate steady state hydrogen plasmas with densities of the order of 10 10 cm -3 and electron temperatures around 4 eV. Hydrogen recycling behavior has been observed in Vehicle-1, and the Arrhenius plot of rate constants exhibits a break at around 300 deg. C. The activation energies are -0.0096 eV and 0.17 eV, respectively, below and above the break. To understand the kinetics of hydrogen recycling, particles sticking coefficients have been measured. Results indicate that at temperatures below the break the sticking process appears to be rate-limiting, whereas above the break surface recombination is important. The sticking coefficients for plasma species have been found to be orders of magnitude larger than those for hydrogen molecules

Hydrogen plasma enhanced alignment on CNT-STM tips grown by liquid catalyst-assisted microwave plasma-enhanced chemical vapor deposition

International Nuclear Information System (INIS)

Tung, Fa-Kuei; Yoshimura, Masamichi; Ueda, Kazuyuki; Ohira, Yutaka; Tanji, Takayoshi

2008-01-01

Carbon nanotubes are grown directly on a scanning tunneling microscopy tip by liquid catalyst-assisted microwave-enhanced chemical vapor deposition, and effects of hydrogen plasma treatment on the tip have been investigated in detail by field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and Raman spectroscopy. The unaligned CNTs on the as-grown tip apex have been realigned and reshaped by subsequent hydrogen plasma treatment. The diameter of CNTs is enlarged mainly due to amorphous layers being re-sputtered over their outer shells

Modification of a liquid hydrogen tank for integrated refrigeration and storage

Science.gov (United States)

Swanger, A. M.; Jumper, K. M.; Fesmire, J. E.; Notardonato, W. U.

2015-12-01

The modification and outfitting of a 125,000-liter liquid hydrogen tank was performed to provide integrated refrigeration and storage capability. These functions include zero boil-off, liquefaction, and densification and therefore require provisions for sub-atmospheric tank pressures within the vacuum-jacketed, multilayer insulated tank. The primary structural modification was to add stiffening rings inside the inner vessel. The internal stiffening rings were designed, built, and installed per the ASME Boiler and Pressure Vessel Code, Section VIII, to prevent collapse in the case of vacuum jacket failure in combination with sub-atmospheric pressure within the tank. For the integrated refrigeration loop, a modular, skeleton-type heat exchanger, with refrigerant temperature instrumentation, was constructed using the stiffening rings as supports. To support the system thermal performance testing, three custom temperature rakes were designed and installed along the 21-meter length of the tank, once again using rings as supports. The temperature rakes included a total of 20 silicon diode temperature sensors mounted both vertically and radially to map the bulk liquid temperature within the tank. The tank modifications were successful and the system is now operational for the research and development of integrated refrigeration technology.

Hydrogen Safety Issues Compared to Safety Issues with Methane and Propane

International Nuclear Information System (INIS)

Green, Michael A.

2005-01-01

The hydrogen economy is not possible if the safety standards currently applied to liquid hydrogen and hydrogen gas by many laboratories are applied to devices that use either liquid or gaseous hydrogen. Methane and propane are commonly used by ordinary people without the special training. This report asks, 'How is hydrogen different from flammable gasses that are commonly being used all over the world?' This report compares the properties of hydrogen, methane and propane and how these properties may relate to safety when they are used in both the liquid and gaseous state. Through such an analysis, sensible safety standards for the large-scale (or even small-scale) use of liquid and gaseous hydrogen systems can be developed. This paper is meant to promote discussion of issues related to hydrogen safety so that engineers designing equipment can factor sensible safety standards into their designs

Hydrogen Safety Issues Compared to Safety Issues with Methane andPropane

Energy Technology Data Exchange (ETDEWEB)

Green, Michael A.

2005-08-20

The hydrogen economy is not possible if the safety standards currently applied to liquid hydrogen and hydrogen gas by many laboratories are applied to devices that use either liquid or gaseous hydrogen. Methane and propane are commonly used by ordinary people without the special training. This report asks, 'How is hydrogen different from flammable gasses that are commonly being used all over the world?' This report compares the properties of hydrogen, methane and propane and how these properties may relate to safety when they are used in both the liquid and gaseous state. Through such an analysis, sensible safety standards for the large-scale (or even small-scale) use of liquid and gaseous hydrogen systems can be developed. This paper is meant to promote discussion of issues related to hydrogen safety so that engineers designing equipment can factor sensible safety standards into their designs.

Optimization of a liquid hydrogen/deuterium target with extremely thin foil windows

International Nuclear Information System (INIS)

Nake, C.J.

1993-09-01

For external experiments at COSY a target of liquid hydrogen or deuterium has been developed, which is very small in order to take advantage of the excellent beam quality of COSY. Targets with thicknesses down to only mm's have been built and operate without bubbles. In order to make the effects of reactions in the windows much smaller than the target reactions, windows with a thickness of about 1.5 μm have been achieved. A novel system which stabilizes the pressure difference between the inside and the outside of the target cell to a small constant value under all target conditions is used. (orig.)

Hydrogen Storage Tank

CERN Multimedia

1983-01-01

This huge stainless steel reservoir,placed near an end of the East Hall, was part of the safety equipment connected to the 2 Metre liquid hydrogen Bubble Chamber. It could store all the hydrogen in case of an emergency. The picture shows the start of its demolition.

Hydrogen in air transportation. Proceedings of the international symposium, Stuttgart, West Germany, September 11-14, 1979, and supplement

Energy Technology Data Exchange (ETDEWEB)

1979-01-01

The Symposium emphasizes future oil prospects, experience with gaseous hydrogen pipeline systems, hydrogen fueled turbofan engines, liquid hydrogen airport requirements, and a liquid hydrogen experimental airline project. Papers were given on the impacts of fossil fuel on the environment, alternate fuels for aircraft, production of hydrogen by coal gasification, production of hydrogen from solar energy and water, handling of hydrogen, liquid hydrogen fueled aircraft, turbofan engine and fuel system for liquid hydrogen use, liquid hydrogen engines, and design concept for LH2 airport facilities.

Study of Liquid Alkanes Production from Biomass-Derived Carbohydrates by Aldol-Condensation and Hydrogenation Processes

Directory of Open Access Journals (Sweden)

Navadol Laosiripojana

2010-10-01

Full Text Available This research aims to synthesis liquid alkanes from biomass-derived hydroxyl methyl furfural (HMF and furfural by aldol-condensation and hydrogenation processes over several catalysts i.e. TiO2, TiO2-ZrO2, Pd/Al2O3 and Pd/CeO2. It was found that the catalysts make significant impact on the selectivity and yield of alkanes product. It is noted that Pd/Al2O3 provided the highest alkane yield and selectivity. The aldol-condensation and hydrogenation of HMF over Pd/Al2O3 provide high C12 selectivity whereas the aldol-condensation and hydrogenation of furfural over Pd/Al2O3 provide high C8 selectivity. The effects of reaction temperature, reaction pressure and reaction time were then studied. The effect of inlet furfural to acetone molar ratio was also determined. It was also found that the optimized conditions to maximize the yield of alkane production from the aldol-condensation/hydrogenation of HMF and furfural are (i at 53oC and 24 hr for aldol-condenstation of HMF, (ii 80oC and 24 hr for aldol-condenstation of furfural, and (iii 120oC for 6 hr with HMF to acetone molar ratio of 3:1 and furfural to acetone molar ratio of 4:1 in the presence of Pd/Al2O3 (calcined at 500oC for hydrogenation reaction.

Calculation of near-edge x-ray-absorption fine structure at finite temperatures: Spectral signatures of hydrogen bond breaking in liquid water

International Nuclear Information System (INIS)

Hetenyi, Balazs; De Angelis, Filippo; Giannozzi, Paolo; Car, Roberto

2004-01-01

We calculate the near-edge x-ray-absorption fine structure of H 2 O in the gas, hexagonal ice, and liquid phases using heuristic density-functional based methods. We present a detailed comparison of our results with experiment. The differences between the ice and water spectra can be rationalized in terms of the breaking of hydrogen bonds around the absorbing molecule. In particular the increase in the pre-edge absorption feature from ice to water is shown to be due to the breaking of a donor hydrogen bond. We also find that in water approximately 19% of hydrogen bonds are broken

The Liquid Metallic Hydrogen Model of the Sun and the Solar Atmosphere VI. Helium in the Chromosphere

Directory of Open Access Journals (Sweden)

Robitaille P.-M.

2013-07-01

Full Text Available Molecular hydrogen and hydrides have recently been advanced as vital agents in the generation of emission spectra in the chromosphere. This is a result of the role they play in the formation of condensed hydrogen structures (CHS within the chromosphere (P.M. Robitaille. The Liquid Metallic Hydrogen Model of the Sun and the Solar Atmosphere IV. On the Nature of the Chromosphere. Progr. Phys., 2013, v. 3, 15–21. Next to hydrogen, helium is perhaps the most intriguing component in this region of the Sun. Much like other elements, which combine with hydrogen to produce hydrides, helium can form the well-known helium hydride molecular ion, HeH+, and the excited neutral helium hydride molecule, HeH∗. While HeH+ is hypothesized to be a key cosmologicalmolecule, its possible presence in the Sun, and that of its excited neutral counterpart, has not been considered. Still, these hydrides are likely to play a role in the synthesis of CHS, as the He I and He II emission lines strongly suggest. In this regard, the study of helium emission spectra can provide insight into the condensed nature of the Sun, especially when considering the 10830 Å line associated with the 23P→2 3S triplet state transition. This line is strong in solar prominences and can be seen clearly on the disk. The excessive population of helium triplet states cannot be adequately explained using the gaseous models, since these states should be depopulated by collisional processes. Conversely, when He-based molecules are used to build CHS in a liquid metallic hydrogen model, an ever increasing population of the 23S and 23P states might be expected. The overpopulation of these triplet states leads to the conclusion that these emission lines are unlikely to be produced through random collisional or photon excitation, as required by the gaseous models. This provides a significant hurdle for these models. Thus, the strong 23P→2 3S lines and the overpopulation of the helium triplet

The equilibrium hydrogen pressure-temperature diagram for the liquid sodium-hydrogen-oxygen system

International Nuclear Information System (INIS)

Knights, C.F.; Whittingham, A.C.

1982-01-01

The underlying equilibria in the sodium-hydrogen-oxygen system are presented in the form of a completmentary hydrogen equilibrium pressure-temperature diagram, constructed by using published data and supplemented by experimental measurements of hydrogen equilibrium pressures over condensed phases in the system. Possible applications of the equilibrium pressure-temperature phase diagram limitations regarding its use are outlined

Salting-out homogenous extraction followed by ionic liquid/ionic liquid liquid-liquid micro-extraction for determination of sulfonamides in blood by high performance liquid chromatography.

Science.gov (United States)

Liu, Zhongling; Yu, Wei; Zhang, Hanqi; Gu, Fanbin; Jin, Xiangqun

2016-12-01

Salting-out homogenous extraction followed by ionic liquid/ionic liquid dispersive liquid-liquid micro-extraction system was developed and applied to the extraction of sulfonamides in blood. High-performance liquid chromatography was applied to the determination of the analytes. The blood sample was centrifuged to obtain the serum. After the proteins in the serum were removed in the presence of acetonitrile, ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate, dipotassium hydrogen phosphate, ionic liquid 1-Hexyl-3-methylimidazolium hexafluorophosphate were added into the resulting solution. After the resulting mixture was ultrasonically shaken and centrifuged, the precipitate was separated. The acetonitrile was added in the precipitate and the analytes were extracted into the acetonitrile phase. The parameters affecting the extraction efficiency, such as volume of ionic liquid, amount of dipotassium hydrogen phosphate, volume of dispersant, extraction time and temperature were investigated. The limits of detection of sulfamethizole (STZ), sulfachlorpyridazine (SCP), sulfamethoxazole (SMX) and Sulfisoxazole (SSZ) were 4.78, 3.99, 5.21 and 3.77μgL -1 , respectively. When the present method was applied to the analysis of real blood samples, the recoveries of analytes ranged from 90.0% to 113.0% and relative standard deviations were lower than 7.2%. Copyright © 2016 Elsevier B.V. All rights reserved.

Hydrogen application dynamics and networks

Energy Technology Data Exchange (ETDEWEB)

Schmidt, E. [Air Liquide Large Industries, Champigny-sur-Marne (France)

2010-12-30

The Chemical Industry consumes large volumes of hydrogen as raw material for the manufacture of numerous products (e.g. polyamides and polyurethanes account for 60% of hydrogen demand). The hydrogen demand was in the recent past and will continue to be driven by the polyurethane family. China will host about 60% of new hydrogen needs over the period 2010-2015 becoming the first hydrogen market next year and reaching 25% of market share by 2015 (vs. only 4% in 2001). Air Liquide supplies large volumes of Hydrogen (and other Industrial Gases) to customers by on-site plants and through pipeline networks which offer significant benefits such as higher safety, reliability and flexibility of supply. Thanks to its long term strategy and heavy investment in large units and pipeline networks, Air Liquide is the Industrial Gas leader in most of the world class Petrochemical basins (Rotterdam, Antwerp, US Gulf Coast, Yosu, Caojing,..) (orig.)

Destructive hydrogenation. [British patent

Energy Technology Data Exchange (ETDEWEB)

1929-07-15

Liquid or readily liquefiable products are obtained from solid distillable carbonaceous materials such as coals, oil shales or other bituminous substances by subjecting the said initial materials to destructive hydrogenation under mild conditions so that the formation of benzine is substantially avoided, and then subjecting the treated material to extraction by solvents. By hydrogenating under mild conditions the heavy oils which prevent the asphaltic substances from being precipitated are preserved, and the separation of the liquid products from the solid residue is facilitated. Solid paraffins and high boiling point constituents suitable for the production of lubricating oils may be removed before or after the extraction process. The extraction is preferably carried out under pressure with solvents which do not precipitate asphaltic substances. Brown coal containing 11 per cent ash is passed at 450/sup 0/C, and 200 atmospheres pressure in counter current to hydrogen; 40 per cent of the coal is converted into liquid products which are condensed out of the hydrogen stream; the pasty residue, on extraction with benzene, yields 45 per cent of high molecular weight products suitable for the production of lubricating oil.

Analyses of one-step liquid hydrogen production from methane and landfill gas

Energy Technology Data Exchange (ETDEWEB)

Huang, Cunping; T-Raissi, Ali [University of Central Florida, Florida Solar Energy Center, 1679 Clearlake Road, Cocoa, FL 32922-5703 (United States)

2007-11-15

Conventional liquid hydrogen (LH{sub 2}) production consists of two basic steps: (1) gaseous hydrogen (GH{sub 2}) production via steam methane reformation followed by purification by means of pressure swing adsorption (PSA), and (2) GH{sub 2} liquefaction. LH{sub 2} produced by the conventional processes is not carbon neutral because of the carbon dioxide (CO{sub 2}) emission from PSA operation. A novel concept is herein presented and flowsheeted for LH{sub 2} production with zero carbon emission using methane (CH{sub 4}) or landfill gas as feedstock. A cryogenic process is used for both H{sub 2} separation/purification and liquefaction. This one-step process can substantially increase the efficiency and reduce costs because no PSA step is required. Furthermore, the integrated process results in no CO{sub 2} emissions and minimal H{sub 2} losses. Of the five flowsheets presented, one that combines low and high temperature CO/CH{sub 4} reforming reactions in a single reactor shows the highest overall efficiency with the first and second law efficiencies of 85% and 56%, respectively. The latter figure assumes 10% overall energy loss and 30% efficiency for the cryogenic process. (author)

Heat transfer by gas-liquid mixture in forced turbulent flow with weak vaporization of the liquid phase (1962); Transfert de chaleur par melange de liquide et de gaz en convection forcee turbulente avec faible vaporisation de la phase liquide (1962)

Energy Technology Data Exchange (ETDEWEB)

Huyghe, J; Mondin, G [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1962-07-01

The present study deals with measures of heat transfer and pressure drop in two-phase liquid flow. The stream is of annular dispersed type, obtained by introducing a small quantity of liquid in a gas turbulent flow. The heat transfer experiments are performed without vaporization of the liquid phase. A notable improvement of the heat transfer coefficient of such a stream is observed, compared with a gas-alone or liquid-alone flow. The improvement concerning the gas-alone is of about 20 when it is compared with the same gas Reynolds's number, of about 8 when it is compared with the same total mass flow rate. A hydrodynamic study of the flow pattern lets us know the original structure of the flow, and allows to foresee the experimental results by means of a simplified theory. (authors) [French] II est fait etat de mesures de transfert thermique et de perte de charge dans un ecoulement en double phase gaz-liquide. L'ecoulement est du type annulaire disperse, obtenu par injection d'une faible quantite de liquide dans un ecoulement gazeux en regime turbulent. Les experiences de transfert thermique sont menees sans vaporisation de la phase liquide. On note une amelioration sensible du coefficient de transfert thermique dans un tel ecoulement par rapport a un ecoulement de gaz seul ou de liquide seul. L'augmentation est de l'ordre de 20 par rapport au gaz seul si on opere a meme nombre de REYNOLDS du gaz, de l'ordre de 8 si on opere a meme debit massique total. Une etude hydrodynamique rapide de l'ecoulement permet de connaitre la structure originale de l'ecoulement, puis de prevoir par une theorie simplifiee le phenomene thermique observe. (auteurs)

Improving the Modeling of Hydrogen Solubility in Heavy Oil Cuts Using an Augmented Grayson Streed (AGS Approach Modélisation améliorée de la solubilité de l’hydrogène dans des coupes lourdes par l’approche de Grayson Streed Augmenté (GSA

Directory of Open Access Journals (Sweden)

Torres R.

2013-04-01

Full Text Available The Grayson Streed (GS method [Grayson H.G. and Streed C.W. (1963 6th World Petroleum Congress , Frankfurt am Main, Germany, 19-26 June, pp. 169-181] is often used by the industry for calculating hydrogen solubility in petroleum fluids. However, its accuracy becomes very bad when very heavy fluids are considered. An improvement is proposed in this work, based on a Flory-augmented activity coefficient model. Hydrogen solubilities in n-alkanes from n−C7 up to n−C36 have been investigated and a decreasing Henry constant with molecular weight is evidenced. The analysis of the Henry constant behaviour with molecular weight suggests a simple improvement to the model, using a Flory entropic contribution, thus keeping its predictive character. This improvement led to the necessity of refitting a number of fundamental hydrogen parameters. The resulting model behaves better for heavy components and for aromatics. The petroleum fractions evaluated with the Augmented Grayson-Streed (AGS model are taken from Cai et al. [Cai H.Y. et al. (2001 Fuel 80, 1055-1063] and Lin et al. [Lin H.M. et al. (1981 Ind. Eng. Chem. Process Des. Dev. 20, 2, 253-256]. The importance of the petroleum fluid characterization is stressed. A sensitivity analysis has shown that the solubility parameter has a much larger effect than the other parameters: great care must be taken at calculating that property. The predictions of hydrogen solubility in petroleum fractions and in coal liquids were improved compared with the Grayson Streed model, resulting in an Absolute Average Deviation (AAD of 30% for AGS model compared to 55% for Grayson-Streed model, in the range of 80-380°C and 6.3-258.9 bar. La méthode de Grayson Streed (GS [Grayson H.G. and Streed C.W. (1963 6th World Petroleum Congress, Frankfurt am Main, Germany, 19-26 June, pp. 169-181] est souvent préconisée dans l’industrie pour calculer la solubilité de l’hydrogène dans des coupes pétrolières. Il se fait

Hydrogen safety

International Nuclear Information System (INIS)

Frazier, W.R.

1991-01-01

The NASA experience with hydrogen began in the 1950s when the National Advisory Committee on Aeronautics (NACA) research on rocket fuels was inherited by the newly formed National Aeronautics and Space Administration (NASA). Initial emphasis on the use of hydrogen as a fuel for high-altitude probes, satellites, and aircraft limited the available data on hydrogen hazards to small quantities of hydrogen. NASA began to use hydrogen as the principal liquid propellant for launch vehicles and quickly determined the need for hydrogen safety documentation to support design and operational requirements. The resulting NASA approach to hydrogen safety requires a joint effort by design and safety engineering to address hydrogen hazards and develop procedures for safe operation of equipment and facilities. NASA also determined the need for rigorous training and certification programs for personnel involved with hydrogen use. NASA's current use of hydrogen is mainly for large heavy-lift vehicle propulsion, which necessitates storage of large quantities for fueling space shots and for testing. Future use will involve new applications such as thermal imaging

Measurements of μ capture rates in liquid hydrogen by the lifetime method

International Nuclear Information System (INIS)

Martino, Jacques.

1982-04-01

The μ capture reaction is a weak interaction. It can be observed as a result of the formation of muonic atoms for which the overlopping of the wave functions of the muon and nucleus is a maximum in the 1s state. The production of this (μp) bound state leads to a capture rate in relatively favorable competition with the disintegration rate. The capture rate for a pulsed muon beam (from the Saclay linear accelerator) was measured in liquid hydrogen by the lifetime method. The method and experimental equipment used for the lifetime measurements are described together with the different sources of systematic error and the results obtained. The interpretation of these results is discussed [fr

Pengaruh Simultan Parameter Suhu dan Konsentrasi Larutan NaOH Terhadap Kuantitas dan Kualitas Hasil Cellulose Powder pada Proses Delignifikasi Tongkol Jagung

Directory of Open Access Journals (Sweden)

Suprianto Suprianto

2015-08-01

Full Text Available Jagung merupakan sumber karbohidrat ketiga di Indonesia setelah padi dan ketela. Produksi jagung Indonesia meningkat terus menerus selama 10 tahun terakhir, yang diikuti dengan konsekuensi meningkatnya tongkol jagung sebagai produk ikutan pertanian jagung. Jumlah tongkol jagung dapat mencapai 40% dari produksi jagung. Fakta ini menunjukkan semakin tinggi potensi tongkol jagung untuk dapat dimanfaatkan bagi penunjang kehidupan manusia. Pemanfaatan tongkol jagung secara langsung sebagai bahan bakar maupun tidak langsung, yaitu melalui tahapan proses fisika dan kimia, sebelum dimanfaatkan langsung, telah mulai banyak menarik perhatian. Penelitian ini dimaksudkan untuk menambah informasi pengolahan tongkol jagung menghasilkan selulosa powder yang dapat digunakan sebagai cellulose gel, selulose membrane filter penjernihan air maupun sebagai bahan baku turunan senyawa selulosa, seperti selulosa asetat, carboxy methyl cellulose dan nitro selulosa.Proses pengolahan tongkol jagung menjadi cellulose prowder dilakukan dalam tiga tahapan proses, masing-masing untuk menghilangkan komponen hemiseluola, lignin dan warna dalam tongkol jagung. Proses tahap pertama menggunakan larutan asam nitrat 7,5% pada suhu 80 o C selama 2 jam, dilanjutkan dengan proses tahap kedua menggunakan larutan NaOH selama 2 jam dengan variasi suhu 80 sampai 100 o C dan variasi konsentrasi NaOH dari 1 N sampai 3 N dan selanjutnya proses tahap ketiga menggunakan hydrogen peroksida dengan konsentrasi 4%, suhu 80 o C dan waktu 2 Jam. Keberhasilan proses diidentifikasi dengan kuantitas dan kualitas hasil cellulose powder.Hasil penelitian menunjukkan bahwa kondisi proses yang baik dalam tahap proses delignifikasi adalah suhu antara 85 sampai 95 o C dan konsentrasi NaOH antara 1,25 N sampai 2 N. Produk pengolahan dari tongkol jagung, dengan proses tiga tahap ini diperoleh hasil cellulose powder warna putih dengan kadar   selulosa sekitar 88 sampai 90%, dengan yield investor sekitar 30

Tritium removal by hydrogen isotopic exchange between hydrogen gas and water on hydrophobic catalyst

International Nuclear Information System (INIS)

Morishita, T.; Isomura, S.; Izawa, H.; Nakane, R.

1980-01-01

Many kinds of the hydrophobic catalysts for hydrogen isotopic exchange between hydrogen gas and water have been prepared. The carriers are the hydrophobic organic materials such as polytetrafluoroethylene(PTFE), monofluorocarbon-PTFE mixture(PTFE-FC), and styrene-divinylbenzene copolymer(SDB). 0.1 to 2 wt % Pt is deposited on the carriers. The Pt/SDB catalyst has much higher activity than the Pt/PTFE catalyst and the Pt/PTFE-FC catalyst shows the intermediate value of catalytic activity. The observation of electron microscope shows that the degrees of dispersion of Pt particles on the hydrophobic carriers result in the difference of catalytic activities. A gas-liquid separated type column containing ten stages is constructed. Each stage is composed of both the hydrophobic catalyst bed for the hydrogen gas/water vapor isotopic exchange and the packed column type bed for the water vapor/liquid water isotopic exchange. In the column hydrogen gas and water flow countercurrently and hydrogen isotopes are separated

Application of Liquid Hydrogen with SMES for Efficient Use of Renewable Energy in the Energy Internet

Directory of Open Access Journals (Sweden)

Xin Wang

2017-02-01

Full Text Available Considering that generally frequency instability problems occur due to abrupt variations in load demand growth and power variations generated by different renewable energy sources (RESs, the application of superconducting magnetic energy storage (SMES may become crucial due to its rapid response features. In this paper, liquid hydrogen with SMES (LIQHYSMES is proposed to play a role in the future energy internet in terms of its combination of the SMES and the liquid hydrogen storage unit, which can help to overcome the capacity limit and high investment cost disadvantages of SMES. The generalized predictive control (GPC algorithm is presented to be appreciatively used to eliminate the frequency deviations of the isolated micro energy grid including the LIQHYSMES and RESs. A benchmark micro energy grid with distributed generators (DGs, electrical vehicle (EV stations, smart loads and a LIQHYSMES unit is modeled in the Matlab/Simulink environment. The simulation results show that the proposed GPC strategy can reschedule the active power output of each component to maintain the stability of the grid. In addition, in order to improve the performance of the SMES, a detailed optimization design of the superconducting coil is conducted, and the optimized SMES unit can offer better technical advantages in damping the frequency fluctuations.

Study of Hydrogen As An Aircraft Fuel

National Research Council Canada - National Science Library

Ciaravino, J

2003-01-01

.... The biggest obstacle to using hydrogen is its very low density, a property that even combined with hydrogen's high heat of combustion still results in very large fuel tanks. Liquid hydrogen (LH2...

On the yield of cold and ultracold neutrons for liquid hydrogen at low temperatures near the melting point

CERN Document Server

Morishima, N

1999-01-01

The neutron scattering cross sections for liquid hydrogen in the temperature range from the melting point to the boiling point are calculated. It is shown that lowering the temperature results in a significant increase in the yield of cold neutrons: for instance, a 44% increase for an incident neutron energy of 19.4 meV. The major cause of this increment is the para-to-ortho transition of a hydrogen molecule though accompanied by an appreciable increase in the density. The results of the cold- and ultracold-neutron yields are discussed in connection with the experimental results of Altarev et al. at the WWR-M reactor.

Storage, generation, and use of hydrogen

Science.gov (United States)

McClaine, Andrew W.; Rolfe, Jonathan L.; Larsen, Christopher A.; Konduri, Ravi K.

2006-05-30

A composition comprising a carrier liquid; a dispersant; and a chemical hydride. The composition can be used in a hydrogen generator to generate hydrogen for use, e.g., as a fuel. A regenerator recovers elemental metal from byproducts of the hydrogen generation process.

Hydrogen storage in insulated pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Aceves, S.M.; Garcia-Villazana, O. [Lawrence Livermore National Lab., CA (United States)

1998-08-01

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LH{sub 2}) or ambient-temperature compressed hydrogen (CH{sub 2}). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (lower energy requirement for hydrogen liquefaction and reduced evaporative losses). This paper shows an evaluation of the applicability of the insulated pressure vessels for light-duty vehicles. The paper shows an evaluation of evaporative losses and insulation requirements and a description of the current analysis and experimental plans for testing insulated pressure vessels. The results show significant advantages to the use of insulated pressure vessels for light-duty vehicles.

Rotational and translational dynamics and their relation to hydrogen bond lifetimes in an ionic liquid by means of NMR relaxation time experiments and molecular dynamics simulation

Science.gov (United States)

Strate, Anne; Neumann, Jan; Overbeck, Viviane; Bonsa, Anne-Marie; Michalik, Dirk; Paschek, Dietmar; Ludwig, Ralf

2018-05-01

We report a concerted theoretical and experimental effort to determine the reorientational dynamics as well as hydrogen bond lifetimes for the doubly ionic hydrogen bond +OH⋯O- in the ionic liquid (2-hydroxyethyl)trimethylammonium bis(trifluoromethylsulfonyl)imide [Ch][NTf2] by using a combination of NMR relaxation time experiments, density functional theory (DFT) calculations, and molecular dynamics (MD) simulations. Due to fast proton exchange, the determination of rotational correlation times is challenging. For molecular liquids, 17O-enhanced proton relaxation time experiments have been used to determine the rotational correlation times for the OH vectors in water or alcohols. As an alternative to those expensive isotopic substitution experiments, we employed a recently introduced approach which is providing access to the rotational dynamics from a single NMR deuteron quadrupolar relaxation time experiment. Here, the deuteron quadrupole coupling constants (DQCCs) are obtained from a relation between the DQCC and the δ1H proton chemical shifts determined from a set of DFT calculated clusters in combination with experimentally determined proton chemical shifts. The NMR-obtained rotational correlation times were compared to those obtained from MD simulations and then related to viscosities for testing the applicability of popular hydrodynamic models. In addition, hydrogen bond lifetimes were derived, using hydrogen bond population correlation functions computed from MD simulations. Here, two different time domains were observed: The short-time contributions to the hydrogen lifetimes and the reorientational correlation times have roughly the same size and are located in the picosecond range, whereas the long-time contributions decay with relaxation times in the nanosecond regime and are related to rather slow diffusion processes. The computed average hydrogen bond lifetime is dominated by the long-time process, highlighting the importance and longevity of

Selective hydrogenation of 1,3-butadiene from crude C{sub 4} cracker stream with a solid catalyst with ionic liquid layer (SCILL). DSC and solubility study

Energy Technology Data Exchange (ETDEWEB)

Mangartz, T.; Korth, W.; Kern, C.; Jess, A. [Bayreuth Univ. (Germany). Dept. of Chemical Engineering

2013-11-01

In petroleum as well as in fine chemical industry, selective catalytic hydrogenation is an important reaction. The selective hydrogenation of 1,3-butadiene (BD) to butene (trans-,1- and cis-butene) from the crude C4 steam cracker fraction represents one example, but under today's technical conditions undesired butane forms inevitably in relevant amounts. To increase the butene yield, the concept of Solid Catalyst with Ionic Liquid Layer (SCILL) was employed. The SCILL catalyst, in contrast to the uncoated catalyst, yielded a remarkably high selectivity to butenes (S{sub butenes} > 99 %) even at high residence times or at high hydrogen partial pressure. Nearly no butane (S{sub butane} {approx} 0 %) was analytically detected. We expected that due to different solubility, the poorer soluble compounds discharged from the ionic liquid and, thus, caused the shift in selectivity to a great extent. Temperature dependent solubility measurements in the used ionic liquid ([DMIM][DMP]) revealed that the order of increasing solubility is 1,3-butadiene > butenes > butane which matches the assumption. However, since differences in solubility cannot explain this SCILL effect satisfyingly, ionic liquids are expected to affect the surface of the catalyst (side-specific ligand-type effect). Investigations using spectroscopic methods (e.g. FTIR) confirmed this suggestion. (orig.)

Sr{sup 90} determination in calcareous water; Determination du {sup 90}Sr dans des eaux chargees en calcium

Energy Technology Data Exchange (ETDEWEB)

Cohen, P; Pardo, G; Wormser, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

The Straub method (ref. 2) for determination of radioactive strontium in water containing calcium is valid within very wide limits, and particularly in the case of residual water from the chemical purification treatment of the radioactive liquid effluent at the C.E.N. Saclay. (author) [French] La methode de Straub (ref. 2) de determination du strontium radioactif dans une eau chargee en calcium est valable dans des limites tres larges et en particulier dans le cas d'eaux residuaires provenant du traitement d'epuration chimique des effluents liquides radioactifs du C.E.N. de Saclay. (auteur)

Carbon Dioxide-Free Hydrogen Production with Integrated Hydrogen Separation and Storage.

Science.gov (United States)

Dürr, Stefan; Müller, Michael; Jorschick, Holger; Helmin, Marta; Bösmann, Andreas; Palkovits, Regina; Wasserscheid, Peter

2017-01-10

An integration of CO 2 -free hydrogen generation through methane decomposition coupled with hydrogen/methane separation and chemical hydrogen storage through liquid organic hydrogen carrier (LOHC) systems is demonstrated. A potential, very interesting application is the upgrading of stranded gas, for example, gas from a remote gas field or associated gas from off-shore oil drilling. Stranded gas can be effectively converted in a catalytic process by methane decomposition into solid carbon and a hydrogen/methane mixture that can be directly fed to a hydrogenation unit to load a LOHC with hydrogen. This allows for a straight-forward separation of hydrogen from CH 4 and conversion of hydrogen to a hydrogen-rich LOHC material. Both, the hydrogen-rich LOHC material and the generated carbon on metal can easily be transported to destinations of further industrial use by established transport systems, like ships or trucks. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Liquid hydrogen mass flow through a multiple orifice Joule-Thomson device

International Nuclear Information System (INIS)

Papell, S.S.; Nyland, T.W.; Saiyed, N.H.

1992-07-01

Liquid hydrogen mass flow rate, pressure drop, and temperature drop data were obtained for a number of multiple orifice Joule-Thomson devices known as visco jets. The present investigation continues a study to develop an equation for predicting two phase flow of cryogens through these devices. The test apparatus design allowed isenthalpic expansion of the cryogen through the visco jets. The data covered a range of inlet and outlet operating conditions. The mass flow rate range single phase or two phase was 0.015 to 0.98 lbm/hr. The manufacturer's equation was found to overpredict the single phase hydrogen data by 10 percent and the two phase data by as much as 27 percent. Two modifications of the equation resulted in a data correlation that predicts both the single and two phase flow across the visco jet. The first modification was of a theoretical nature, and the second strictly empirical. The former reduced the spread in the two phase data. It was a multiplication factor of 1-X applied to the manufacturer's equation. The parameter X is the flow quality downstream of the visco jet based on isenthalpic expansion across the device. The latter modification was a 10 percent correction term that correlated 90 percent of the single and two phase data to within +/- 10 percent scatter band. 3 refs

Hydrogen production from coal using a nuclear heat source

Science.gov (United States)

Quade, R. N.

1976-01-01

A strong candidate for hydrogen production in the intermediate time frame of 1985 to 1995 is a coal-based process using a high-temperature gas-cooled reactor (HTGR) as a heat source. Expected process efficiencies in the range of 60 to 70% are considerably higher than all other hydrogen production processes except steam reforming of a natural gas. The process involves the preparation of a coal liquid, hydrogasification of that liquid, and steam reforming of the resulting gaseous or light liquid product. A study showing process efficiency and cost of hydrogen vs nuclear reactor core outlet temperature has been completed, and shows diminishing returns at process temperatures above about 1500 F. A possible scenario combining the relatively abundant and low-cost Western coal deposits with the Gulf Coast hydrogen users is presented which provides high-energy density transportation utilizing coal liquids and uranium.

RENDEMEN DAN KOMPOSISI PROKSIMAT GELATIN KULIT IKAN BELUT DAN LELE PADA KEADAAN SEGAR DAN KERING (YIELD AND PROXIMATE OF GELATIN EXTRACTED FROM FRESH AND DRY SWAMP ELL AND CATFISH SKIN

Directory of Open Access Journals (Sweden)

Hafni Rahmawati

2017-02-01

Full Text Available Kulit ikan belut dan lele berpotensi untuk diekstrak gelatinnya. Kulit ikan belut dan lele tidak bersisik, berlendir dan berlemak untuk ikan lele, berbeda dengan kulit ikan pada umumnya yang dijadikan gelatin. Penelitian ini mempelajari tentang gelatin kulit ikan belut dan lele dari segi rendemen dan komposisi proksimat. Untuk mengetahui pengaruh pengeringan, kondisi kulit segar dan kering juga dipelajari. Tahapan ekstraksi yang dilakukan untuk keseluruhan jenis ikan sama, kecuali penanganan kulit ikan kering yang sebelumnya direndam dalam air selama 4 jam. Kulit ikan direndam kembali dalam 0,05M asam asetat selama 10 jam, kemudian dicuci dan diekstraksi dengan aquadest pada suhu 80OC selama 2 jam, cairan yang didapat difiltrasi. Filtratnya dikeringkan dalam cabinet dryer suhu 55OC selama        48 jam hingga diperoleh lembaran gelatin, kemudian diblender menjadi granula gelatin. Hasil penelitian menunjukkan bahwa gelatin kulit ikan kering mempunyai rendemen sedikit lebih rendah dibandingkan gelatin dari kulit ikan segarnya. Kadar protein gelatin kulit ikan kering telihat tinggi dibandingkan kulit segarnya. Pengeringan kulit ikan berpengaruh pada penurunan kadar abu dan lemak, namun tidak mempengaruhi kadar air gelatin hasil ekstraksi. Gelatin kulit segar ikan lele memiliki nilai rendemen tertinggi yaitu 22,01%. Komposisi proksimat yang terbaik diantara keseluruhan kondisi dan jenis kulit dapat dilihat pada gelatin kulit segar ikan belut dimana memiliki kadar air 9,91%; kadar abu 3,07%; kadar protein 91,61%; dan kadar lemak 0,82%. Skin of swam ell and catfish were potential to gelatin extracted. Swamp ell skin doesn’t have scales, with much mucus and a few fat for catfish, it’s different from another fish skin that gelatin extracted usually. This research was studied yield and proximate gelatin extracted from skin of swam ell and catfish. Influence of drying was observed too. The first stage of the research was raw

Investigation of hydrogen usage in aviation industry

International Nuclear Information System (INIS)

Yılmaz, İlker; İlbaş, Mustafa; Taştan, Murat; Tarhan, Cevahir

2012-01-01

Highlights: ► We examine usage of liquid hydrogen as a fuel in aircrafts. ► Engine performance is a little better for liquid hydrogen fuel than kerosene. ► Liquid hydrogen can be a potential alternative to kerosene as aviation fuel. ► Usage of liquid hydrogen will provide national independence for fuel supply. ► Increased production of liquid hydrogen will decrease its cost disadvantage. - Abstract: Fossil-based fuels are commonly used in aircraft engines but they have a polluting effect and they cause a greenhouse effect for our world. This study reports a research about aircraft gas turbine engines which are fired by liquid hydrogen (LH 2 ) in terms of performance and environmental aspects. Also, the performance and emissions of LH 2 fueled engines are compared with those of kerosene fired aircraft engines. Same flights from Istanbul to London, and Paris to Kabul are examined to estimate the emission from a conventional aircraft as an application in aviation sector. It is shown that the amount of NO x , HC and CO emissions for traveling by a conventional aircraft for London is 78.36, 1.202 and 22.4 kg, while Paris is 71.55, 1.171 and 21.63 kg, and Kabul is 111.44, 1.36 and 26.11 kg, respectively. For the use of liquid hydrogen as a fuel, amount of gas emissions decreases for any destination like London, Paris and Kabul. Total HC and CO emissions are going to be nearly 0 kg because of lack of carbon in the fuel. Also NO x emission is lower because of wider flammability limit of LH 2 . Results show that the aircraft engines with LH 2 have great potential for emissions reduction and engine performance parameters are a little better for LH 2 fuel. It is strongly emphasized that one of the most important advantages for the use of LH 2 is national independence for fuel supply. Oil cannot be extracted in every countries territory but LH 2 is producible for every country and this is so important for a countries freedom.

Methods for continuous or semi-continuous analysis of gases dissolved in pressurized water; Methodes d'analyses continue et semi-continue de gaz dissous dans l'eau surpressee

Energy Technology Data Exchange (ETDEWEB)

Vignet, P; Gabilly, R; Lutz, J; Zermizogilou, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

Hydrogen analyser: The relative variation of the resistance of a palladium or platinum-palladium alloy wire immersed in water, is measured during the absorption of hydrogen. The calibration curves have been determined for a Pd wire at temperatures from 180 to 280 deg. C. At low temperatures a palladium-platinum alloy has been used. The best conditions of operation for the analysis have been determined from the theoretical and experimental studies of tho absorption of hydrogen dissolved in water by a metal. Oxygen analyser: It is well known that the oxygen dissolved in water reacts with thallium metal to give thallium hydroxide. This compound is soluble and increases the electrical conductivity of the water. This increase in conductivity is directly proportional to the oxygen concentration. A differential conductivity meter has been developed for the measurement of dissolved oxygen. The range of this apparatus extend from 10{sup -3} to 10{sup 2} and more, ppm of O{sub 2} dissolved in water. It enables the direct determination of O{sub 2} dissolved in in electrolytes without reducing their conductivity. The best conditions for a low chemical background noise have been determined and a relation for the calibration has been established. The rate of conversion of oxygen into thallium hydroxide is related to the dimensions of the thallium bed. Analysis of the total amount of gases dissolved in water: A sample of water at high temperature and pressure is isolated in a bomb placed in a by-pass of a pressurized loop. The water is out-gassed by cooling and the pressure of the gases above the liquid phase is measured. This pressure is a function of the total amount of dissolved gases in water. By using an eudiometric method, the fraction of combustible gas can be measured. The calibration curves have been computed and checked experimentally. The time for a measurement is 30 minutes, the precision better than {+-} 5 per cent and the sensitivity higher that 1 cm{sup 3} H{sub 2

Hydrogen and Nitrogen Control in Ladle and Casting Operations

Energy Technology Data Exchange (ETDEWEB)

Richard J. Fruehan; Siddhartha Misra

2005-01-15

In recent years there has been an increasing demand to reduce and control the amount of dissolved gases in steel. Hydrogen and nitrogen are two of the most important gases which when dissolved in liquid steel affect its properties significantly. Several steelmaking additions have been investigated in this research for their effect on the hydrogen and nitrogen content of steels. It has been established that calcium hydroxide (hydrated lime) acts as a source of hydrogen. Carburizers, such as metallurgical coke, were found to result in no hydrogen pickup when added to liquid steel. Addition of petroleum coke, on the other hand, increased the hydrogen content of liquid steel. Ferroalloy such as medium carbon ferromanganese when added to the liquid iron was found to increase its nitrogen content, the increase being proportional to the amount of ferroalloy added. Similarly, addition of pitch coke, which had a significant nitrogen impurity, increased the nitrogen content of liquid iron. A mathematical model was developed to quantify the absorption of nitrogen and hydrogen from the air bubbles entrained during tapping of liquid steel. During the bottom stirring of liquid metal in a ladle, the inert gas escaping from the top displaces the slag layer and often forms an open eye. The absorption of atmospheric nitrogen through the spout eye was estimated for different slag thickness and gas flow rate. The ultimate goal of this research was to develop a comprehensive set of equations which could predict the nitrogen and hydrogen pickup from their various sources. Estimates of hydrogen and nitrogen pickup during the steel transfer operations such as tapping and ladle stirring and the predicted pickup from steelmaking additions were integrated into empirical equations. The comprehensive model is designed to predict the gas pickup under varying operating conditions such as the metal oxygen and sulfur content, the total tapping or stirring time, the stirring gas flow rate and the

Spray Bar Zero-Gravity Vent System for On-Orbit Liquid Hydrogen Storage

Science.gov (United States)

Hastings, L. J.; Flachbart, R. H.; Martin, J. J.; Hedayat, A.; Fazah, M.; Lak, T.; Nguyen, H.; Bailey, J. W.

2003-01-01

During zero-gravity orbital cryogenic propulsion operations, a thermodynamic vent system (TVS) concept is expected to maintain tank pressure control without propellant resettling. In this case, a longitudinal spray bar mixer system, coupled with a Joule-Thompson (J-T) valve and heat exchanger, was evaluated in a series of TVS tests using the 18 cu m multipurpose hydrogen test bed. Tests performed at fill levels of 90, 50, and 25 percent, coupled with heat tank leaks of about 20 and 50 W, successfully demonstrated tank pressure control within a 7-kPa band. Based on limited testing, the presence of helium constrained the energy exchange between the gaseous and liquid hydrogen (LH2) during the mixing cycles. A transient analytical model, formulated to characterize TVS performance, was used to correlate the test data. During self-pressurization cycles following tank lockup, the model predicted faster pressure rise rates than were measured; however, once the system entered the cyclic self-pressurization/mixing/venting operational mode, the modeled and measured data were quite similar. During a special test at the 25-percent fill level, the J-T valve was allowed to remain open and successfully reduced the bulk LH2 saturation pressure from 133 to 70 kPa in 188 min.

Development of Fe-based superconducting wires for liquid-hydrogen level sensors

Science.gov (United States)

Ishida, S.; Tsuchiya, Y.; Mawatari, Y.; Eisaki, H.; Nakano, A.; Yoshida, Y.

2017-07-01

We developed liquid-hydrogen (LH2) level sensors with Ba(Fe1-x Co x )2As2 superconducting wires (Co-Ba122 wires) as their detection elements. We fabricated Co-Ba122 wires with different Co concentrations x by using the powder-in-tube method. The superconducting transition temperatures of the wires were successfully controlled in the range of 20-25 K by changing x from 0.06 to 0.10. The resistance-temperature curves of the wires exhibited sharp superconducting transitions with widths of 0.5-1.0 K. In addition, we performed an operation test of the Co-Ba122 level sensors with LH2. Close correspondence between the output resistance and the actual LH2 level was observed for a sensor equipped with x = 0.09 wire, demonstrating that this sensor can accurately measure LH2 levels.

Renewable energy carriers: Hydrogen or liquid air/nitrogen?

International Nuclear Information System (INIS)

Li Yongliang; Chen Haisheng; Zhang Xinjing; Tan Chunqing; Ding Yulong

2010-01-01

The world's energy demand is met mainly by the fossil fuels today. The use of such fuels, however, causes serious environmental issues, including global warming, ozone layer depletion and acid rains. A sustainable solution to the issues is to replace the fossil fuels with renewable ones. Implementing such a solution, however, requires overcoming a number of technological barriers including low energy density, intermittent supply and mobility of the renewable energy sources. A potential approach to overcoming these barriers is to use an appropriate energy carrier, which can store, transport and distribute energy. The work to be reported in this paper aims to assess and compare a chemical energy carrier, hydrogen, with a physical energy carrier, liquid air/nitrogen, and discuss potential applications of the physical carrier. The ocean energy is used as an example of the renewable energy sources in the work. The assessment and comparison are carried out in terms of the overall efficiency, including production, storage/transportation and energy extraction. The environmental impact, waste heat recovery and safety issues are also considered. It is found that the physical energy carrier may be a better alternative to the chemical energy carrier under some circumstances, particularly when there are waste heat sources.

Analysis of a gas-liquid film plasma reactor for organic compound oxidation

Energy Technology Data Exchange (ETDEWEB)

Hsieh, Kevin [Department of Chemical and Biomedical Engineering, Florida State University, Tallahassee, FL 32310 (United States); Wang, Huijuan [School of Environmental and Safety Engineering, Jiangsu University, Zhenjiang 212013 (China); Locke, Bruce R., E-mail: blocke@fsu.edu [Department of Chemical and Biomedical Engineering, Florida State University, Tallahassee, FL 32310 (United States)

2016-11-05

Highlights: • Non-homogeneous filamentary plasma discharge formed along gas-liquid interface. • Hydrogen peroxide formed near interface favored over organic oxidation from liquid. • Post-plasma Fenton reactions lead to complete utilization of hydrogen peroxide. - Abstract: A pulsed electrical discharge plasma formed in a tubular reactor with flowing argon carrier gas and a liquid water film was analyzed using methylene blue as a liquid phase hydroxyl radical scavenger and simultaneous measurements of hydrogen peroxide formation. The effects of liquid flow rate, liquid conductivity, concentration of dye, and the addition of ferrous ion on dye decoloration and degradation were determined. Higher liquid flow rates and concentrations of dye resulted in less decoloration percentages and hydrogen peroxide formation due to initial liquid conductivity effects and lower residence times in the reactor. The highest decoloration energy yield of dye found in these studies was 5.2 g/kWh when using the higher liquid flow rate and adding the catalyst. The non-homogeneous nature of the plasma discharge favors the production of hydrogen peroxide in the plasma-liquid interface over the chemical oxidation of the organic in the bulk liquid phase and post-plasma reactions with the Fenton catalyst lead to complete utilization of the plasma-formed hydrogen peroxide.

Propagation and diffusion of a plasma column in a magnetic field; Propagation et diffusion d'une colonne de plasma dans un champ magnetique

Energy Technology Data Exchange (ETDEWEB)

Bottiglioni, F; Coutant, J; Gadda, E; Prevot, F [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1966-12-01

A plasma column is created in a magnetic field by longitudinal diffusion from a low-pressure pulsed discharge in hydrogen. Depending on the discharge conditions, two regimes are obtained in which the gas pumping speed has a different effect upon the plasma density in the column. Calculations are presented which can explain this effect by a difference in the transverse diffusion coefficient. (authors) [French] On forme une colonne de plasma dans un champ magnetique par diffusion longitudinale a partir d'une decharge puisee dans l'hydrogene a basse pression. Selon les conditions de la decharge on observe deux regimes differents pour lesquels le pompage du gaz neutre a un effet different sur la densite resultante du plasma dans la colonne. On presente des calculs qui peuvent expliquer cet effet par une difference dans la diffusion transversale du plasma. (auteurs)

Perancangan Sistem Pemantauan Gas dan Peringatan pada Ruangan melalui Jaringan Nirkabel

Directory of Open Access Journals (Sweden)

Gunawan Kunto Bhasworo

2018-01-01

Full Text Available Udara adalah suatu campuran gas yang terdapat pada  lapisan yang mengelilingi bumi. Gas CO merupakan salah satu gas yang mengandung  zat yang tidak baik yang tidak dapat ditangkap oleh panca indera, gas tersebut bersifat membunuh makhluk hidup termasuk manusia. Hidrogen sulfida  (H2S adalah gas yang tidak berwarna, beracun, mudah terbakar dan berbau seperti telur busuk. . Konsentrasi H2S dalam jumlah yang rendah, dapat membahayakan keselamatan manusia. Dalam konsentrasi 100 PPM dapat menyebabkan kematian dalam waktu 2-5 menit. Tidak kalah berbahayanya adalah hydrocarbon gas exploison atau ledakan yang diakibatkan kebocoran LPG (metana pada ruang tertutup. Penelitian ini bertujuan untuk merancang dan mengimplementasikan sebuah sistem pemantau gas dan peringatan pada ruangan melalui jaringan nirkabel. Dengan menggabungkan PC (Personal Computer, Arduino, Arduino Wifi shield, Router, LCD (Liquid Crystal Display, Buzzer serta sensor gas TGS 2620 dan 2602 serta 2442 yang merupakan sensor-sensor dengan sensitivitas yang tinggi terhadap gas LPG (metana dan H2S serta CO dengan konsumsi daya rendah. Di peroleh sistem pemantau gas dan peringatan pada ruangan melalui jaringan nirkabel yang dapat mendeteksi dan memberikan peringatan apabila ada gas-gas berbahaya CO, H2S dan LPG (metana

New concepts in hydrogen production in Iceland

International Nuclear Information System (INIS)

Arnason, B.; Sigfusson, T.I.; Jonsson, V.K.

1993-01-01

The paper presents some new concepts of hydrogen production in Iceland for domestic use and export. A brief overview of the Icelandic energy consumption and available resources is given. The cost of producing hydrogen by electrolysis is calculated for various alternatives such as plant size, load factors and electricity cost. Comparison is made between the total cost of liquid hydrogen delivered to Europe from Iceland and from Northern America, showing that liquid hydrogen delivered to Europe from Iceland would be 9% less expensive. This assumes conventional technology. New technologies are suggested in the paper and different scenarios for geothermally assisted hydrogen production and liquefaction are discussed. It is estimated that the use of geothermal steam would lead to 19% lower hydrogen gas production costs. By analysing the Icelandic fishing fleet, a very large consumer of imported fuel, it is argued that a transition of fuel technology from oil to hydrogen may be a feasible future option for Iceland and a testing ground for changing fuel technology. (Author)

Liquid-vapour surface sensors for liquid nitrogen and hydrogen

Science.gov (United States)

Siegwarth, J. D.; Voth, R. O.; Snyder, S. M.

1992-01-01

The present paper identifies devices to serve as liquid-vapor detectors in zero gravity. The testing in LH2 was done in a sealed glass Dewar system to eliminate any chance of mixing H2 and air. Most of the tests were performed with the leads to the sensor horizontal. Some results of rapid cycle testing of LVDG in LH2 are presented. Findings of rapid-cycle testing of LVDG in LH2 are discussed. The sensor crossed the liquid surface when the position sensor registered 1.9 V, which occurred at about 0.4075 s. The delay time was about 1.5 ms. From the estimated slope of the position sensor curve at 1.9 V, the velocity of the sensor through the liquid surface is over 3 m/s. Results of tests of optical sensors are presented as well.

Storing Renewable Energy in the Hydrogen Cycle.

Science.gov (United States)

Züttel, Andreas; Callini, Elsa; Kato, Shunsuke; Atakli, Züleyha Özlem Kocabas

2015-01-01

An energy economy based on renewable energy requires massive energy storage, approx. half of the annual energy consumption. Therefore, the production of a synthetic energy carrier, e.g. hydrogen, is necessary. The hydrogen cycle, i.e. production of hydrogen from water by renewable energy, storage and use of hydrogen in fuel cells, combustion engines or turbines is a closed cycle. Electrolysis splits water into hydrogen and oxygen and represents a mature technology in the power range up to 100 kW. However, the major technological challenge is to build electrolyzers in the power range of several MW producing high purity hydrogen with a high efficiency. After the production of hydrogen, large scale and safe hydrogen storage is required. Hydrogen is stored either as a molecule or as an atom in the case of hydrides. The maximum volumetric hydrogen density of a molecular hydrogen storage is limited to the density of liquid hydrogen. In a complex hydride the hydrogen density is limited to 20 mass% and 150 kg/m(3) which corresponds to twice the density of liquid hydrogen. Current research focuses on the investigation of new storage materials based on combinations of complex hydrides with amides and the understanding of the hydrogen sorption mechanism in order to better control the reaction for the hydrogen storage applications.

Large-Scale Liquid Hydrogen Tank Rapid Chill and Fill Testing for the Advanced Shuttle Upper Stage Concept

Science.gov (United States)

Flachbart, R. H.; Hedayat, A.; Holt, K. A.; Sims, J.; Johnson, E. F.; Hastings, L. J.; Lak, T.

2013-01-01

Cryogenic upper stages in the Space Shuttle program were prohibited primarily due to a safety risk of a 'return to launch site' abort. An upper stage concept addressed this concern by proposing that the stage be launched empty and filled using shuttle external tank residuals after the atmospheric pressure could no longer sustain an explosion. However, only about 5 minutes was allowed for tank fill. Liquid hydrogen testing was conducted within a near-ambient environment using the multipurpose hydrogen test bed 638.5 ft3 (18m3) cylindrical tank with a spray bar mounted longitudinally inside. Although the tank was filled within 5 minutes, chilldown of the tank structure was incomplete, and excessive tank pressures occurred upon vent valve closure. Elevated tank wall temperatures below the liquid level were clearly characteristic of film boiling. The test results have substantial implications for on-orbit cryogen transfer since the formation of a vapor film would be much less inhibited due to the reduced gravity. However, the heavy tank walls could become an asset in normal gravity testing for on-orbit transfer, i.e., if film boiling in a nonflight weight tank can be inhibited in normal gravity, then analytical modeling anchored with the data could be applied to reduced gravity environments with increased confidence.

Analgesic effect of coconut shell (Cocos nucifera L liquid smoke on mice

Directory of Open Access Journals (Sweden)

Meircurius Dwi C.S

2012-09-01

selulosa, petosan, lignin, solvent, uronat unhidrat, nitrogen dan air. Salah satu bahan aktif dalam tempurung kelapa adalah phenyl propanoid (terdapat dalam struktur lignin dan guaiakol. Phenyl propanoid dan guaiakol adalah suatu senyawa fenol yang mempunyai sifat sebagai antioksidan, antiseptic, anti-inflamasi, anastesi dan analgesik. Liquid smoke tempurung kelapa (Cocos nucifera Lmengandung senyawa fenol yang dapat mengikat komponen dalam konversi asam arakhidonat menjadi prostaglandin. Tujuan: Studi ini bertujuan untuk meneliti efek analgesik dari liquid smoke tempurung kelapa (Cocos nucifera L. Metode: Penelitian ini adalah eksperimental laboratoris dengan jenis post test only control group design pada mencit (Mus musculus jantan usia 2-3 bulan dengan berat badan 20-30gram. Kelompok kontrol dan perlakuan terdiri dari 7 hewan coba. Kelompok kontrol diberi aquades 0.01ml/bb (ml/gr (po dan setelah 30 menit diberi asam asetat 0.6% 0.01ml/bb (ml/gr (ip. Kelompok perlakuan diberi liquid smoke tempurung kelapa (Cocos nucifera L dengan konsentrasi 25%, 50% and 100%. Efek analgesik ditentukan dengan melihat penurunan writhing reflex (liukan atau geliat tubuh hewan coba yang dihitung setiap 5 menit selama 30 menit. Hasil: Terdapat perbedaan yang bermakna jumlah writhing reflex pada pemberian liquid smoke tempurung kelapa konsentrasi 25%, 50% dan 100%. Semakin tinggi konsentrasi liquid smoke, semakin tinggi pula efek analgesic yang ditimbulkan. Kesimpulan: Liquid smoke tempurung kelapa mempunyai efek analgesik.

Design and Development of New Carbon-Based Sorbent Systems for an Effective Containment of Hydrogen

Energy Technology Data Exchange (ETDEWEB)

Alan C. Cooper

2012-05-03

This is a summary for work performed under cooperative agreement DE FC36 04GO14006 (Design and Development of New Carbon-based Sorbent Systems for an Effective Containment of Hydrogen). The project was directed to discover new solid and liquid materials that use reversible catalytic hydrogenation as the mechanism for hydrogen capture and storage. After a short period of investigation of solid materials, the inherent advantages of storing and transporting hydrogen using liquid-phase materials focused our attention exclusively on organic liquid hydrogen carriers (liquid carriers). While liquid carriers such as decalin and methylcyclohexane were known in the literature, these carriers suffer from practical disadvantages such as the need for very high temperatures to release hydrogen from the carriers and difficult separation of the carriers from the hydrogen. In this project, we were successful in using the prediction of reaction thermodynamics to discover liquid carriers that operate at temperatures up to 150 C lower than the previously known carriers. The means for modifying the thermodynamics of liquid carriers involved the use of certain molecular structures and incorporation of elements other than carbon into the carrier structure. The temperature decrease due to the more favorable reaction thermodynamics results in less energy input to release hydrogen from the carriers. For the first time, the catalytic reaction required to release hydrogen from the carriers could be conducted with the carrier remaining in the liquid phase. This has the beneficial effect of providing a simple means to separate the hydrogen from the carrier.

Refinement of the experimental dynamic structure factor for liquid para-hydrogen and ortho-deuterium using semi-classical quantum simulation

International Nuclear Information System (INIS)

Smith, Kyle K. G.; Rossky, Peter J.; Poulsen, Jens Aage; Cunsolo, A.

2014-01-01

The dynamic structure factor of liquid para-hydrogen and ortho-deuterium in corresponding thermodynamic states (T = 20.0 K, n = 21.24 nm −3 ) and (T = 23.0 K, n = 24.61 nm −3 ), respectively, has been computed by both the Feynman-Kleinert linearized path-integral (FK-LPI) and Ring-Polymer Molecular Dynamics (RPMD) methods and compared with Inelastic X Ray Scattering spectra. The combined use of computational and experimental methods enabled us to reduce experimental uncertainties in the determination of the true sample spectrum. Furthermore, the refined experimental spectrum of para-hydrogen and ortho-deuterium is consistently reproduced by both FK-LPI and RPMD results at momentum transfers lower than 12.8 nm −1 . At larger momentum transfers the FK-LPI results agree with experiment much better for ortho-deuterium than for para-hydrogen. More specifically we found that for k ∼ 20.0 nm −1 para-hydrogen provides a test case for improved approximations to quantum dynamics

Zero boil-off methods for large-scale liquid hydrogen tanks using integrated refrigeration and storage

Science.gov (United States)

Notardonato, W. U.; Swanger, A. M.; E Fesmire, J.; Jumper, K. M.; Johnson, W. L.; Tomsik, T. M.

2017-12-01

NASA has completed a series of tests at the Kennedy Space Center to demonstrate the capability of using integrated refrigeration and storage (IRAS) to remove energy from a liquid hydrogen (LH2) tank and control the state of the propellant. A primary test objective was the keeping and storing of the liquid in a zero boil-off state, so that the total heat leak entering the tank is removed by a cryogenic refrigerator with an internal heat exchanger. The LH2 is therefore stored and kept with zero losses for an indefinite period of time. The LH2 tank is a horizontal cylindrical geometry with a vacuum-jacketed, multilayer insulation system and a capacity of 125,000 liters. The closed-loop helium refrigeration system was a Linde LR1620 capable of 390W cooling at 20K (without any liquid nitrogen pre-cooling). Three different control methods were used to obtain zero boil-off: temperature control of the helium refrigerant, refrigerator control using the tank pressure sensor, and duty cycling (on/off) of the refrigerator as needed. Summarized are the IRAS design approach, zero boil-off control methods, and results of the series of zero boil-off tests.

PENGARUH MEKANISME CORPORATE GOVERNANCE, KUALITAS AUDITOR EKSTERNAL, DAN LIKUIDITAS TERHADAP KUALITAS LABA

Directory of Open Access Journals (Sweden)

Amanita Novi Yushita

2013-10-01

Full Text Available Abstrak: Pengaruh Mekanisme Corporate Governance, Kualitas Auditor Eksternal, dan Likuiditas Terhadap Kualitas Laba. Tujuan penelitian ini adalah memberikan bukti empiris pengaruh penerapan mekanisme corporate governance yang terdiri dari struktur dewan direksi, kepemilikan manajerial, kepemilikan institusional, komite audit, dan komisaris independen terhadap kualitas laba. Penelitian ini menggunakan sampel sebanyak 22 perusahaan manufaktur yang listing di BEI pada periode 2007-2011. Analisis GLS digunakan sebagai teknik analisis data dalam penelitian ini. Hasil penelitian menunjukkan bahwa struktur dewan direksi, komisaris independen berpengaruh positif dan signifikan terhadap Discretionary Accrual (DTAC atau berpengaruh negatif terhadap kualitas laba. Kemudian kualitas auditor eksternal berpengaruh negatif dan signifikan terhadap Discretionary Accrual (DTAC atau berpengaruh positif terhadap kualitas laba. Sedangkan kepemilikan manajerial, kepemilikan institusional, komite audit, dan likuiditas tidak berpengaruh signifikan terhadap kualitas laba.   Kata kunci: corporate governance, kualitas auditor eksternal, likuiditas, kualitas laba. Abstract: The influence of Corporate Governance Mechanism, External Auditor Quality, and Liquidity on the Quality of Earnings. The purpose of this study is to provide empirical evidence of the effect of the application of corporate governance mechanisms consisting of board structure, managerial ownership, institutional ownership, audit committees and independent commissioners on the quality of earnings. This study used a sample of 22 manufacturing companies listed on the Stock Exchange in the period 2007-2011. GLS analysis is used as a data analysis technique in this study. The results showed that the board structure and the proportions of independent commissioner have a positive and significant effect to discretionary accrual (DTAC or have a negative effect to the earnings quality. The quality of external

Study of hyperon-antihyperon production in antiproton-proton collision at 4 GeV/c; Etude de la production d'hyperon et d'antihyperon dans les collisions antiproton-proton a 4 GeV/c

Energy Technology Data Exchange (ETDEWEB)

Revel, D [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-05-15

We present the results on hyperon-antihyperon production by 4 GeV/c antiprotons in hydrogen. We used about 10{sup 5} pictures taken in an antiproton beam from the CERN proton synchrotron with the 81 cm Saclay hydrogen bubble chamber. The aim of this work was the study, through the cross sections and the angular distributions, of production mechanism of hyperon antihyperon pairs and excited hyperons (or antihyperons). For most of the channels, these angular distributions show a strong forward peaking of the antihyperon in the center of mass of the interaction. This suggests that a peripheral-type mechanism is predominant in these processes. We compare the results of some cross sections, with theoretical predictions according to SU{sub 3} unitary symmetry. (author) [French] Nous presentons ici des resultats concernant la production d'hyperons et d'antihyperons dans l'interaction antiproton sur proton a 4 GeV/c. Nous avons utilise pour cette experience un lot de 10{sup 5} photographies, prises avec la chambre a bulles de 81 cm a hydrogene liquide de Saclay, placee dans un faisceau d'antiprotons aupres du synchrotron a protons du CERN. Le but de ce travail etait l'etude des mecanismes de production des paires hyperons antihyperons et des hyperons excites (antihyperons excites) au travers des sections efficaces et des distributions angulaires. Pour la plupart des voies, ces distributions angulaires, dans le systeme du centre de masse, indiquent une forte tendance a l'emission vers l'avant de l'antihyperon, ce qui suggere un mecanisme de production de type peripherique. Nous avons compare les resultats de certaines sections efficaces avec des previsions obtenues a partir de la theorie de symetrie unitaire SU{sub 3}. (auteur)

Achievement report for fiscal 1998 on World Energy Network (WE-NET). Subtask 5. Development of hydrogen transportation and storage technologies (development of liquid hydrogen storage facilities); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5. Suiso yuso chozo gijutsu no kaiahtsu (ekitai suiso chozo setsubi no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An insulation structure suitable for large tanks was tested for insulation capability and strength at the liquid hydrogen temperature for the development of liquid hydrogen storage facilities. For the insulation test, a specimen was built of a porous solid material, and the specimen was given an additional duty of serving a test of a high temperature plate that was to impose loads on the specimen. The test conditions were not met, however, with too much variation in presence in temperature distribution. For the structural material compressive strength test, a method was worked out involving a hard urethane foam material specimen in liquid hydrogen, and was implemented. It was found that the specimen fracture that occurred was in the form of the collapse of the loaded surface. Tests were conducted at three temperatures, which were the normal temperature, the liquid nitrogen temperature, and the liquid hydrogen temperature, and compressive strength was determined for each of the three cases. No great difference in strength resulted from the difference between the two low temperatures. As for compressive strength at low temperatures, it was found that the strength was approximately two times greater than at the normal temperature. The above findings indicate that hard polyurethane foam is on the safe side when it is designed for the normal temperature. (NEDO)

Hydrogenation and hydrodeoxygenation of difurfurylidene acetone to liquid alkanes over Raney Ni and the supported Pt catalysts

International Nuclear Information System (INIS)

Li, Yuping; Huang, Xiaoming; Zhang, Qian; Chen, Lungang; Zhang, Xinghua; Wang, Tiejun; Ma, Longlong

2015-01-01

Highlights: • The C_8−C_1_4 alkane yield of 82.9% was obtained in the two-step hydrogenation/HDO process. • Protonation effect from methanol solvent increased F_2A conversion in the two-step process. • The rate-determining step was acyl C=O bond hydrogenation in the first step of F_2A hydrogenation. • The acidic centers from SiO_2−ZrO_2 activated the acyl and oxygen atoms of intermediates. • Acidity of SiO_2−ZrO_2 and Pt active centers of 1 wt%Pt/SiO_2−ZrO_2 resulted stable HDO performance. - Abstract: Direct HDO process for difurfurylidene acetone dimer (F_2A) conversion to liquid alkanes (C_8−C_1_4) at 260 °C in a batch reactor was investigated over different material supported 1 wt%Pt catalysts, including SAPO-11, HZSM-5, SiO_2−Al_2O_3, MCM-22, and home-made SiO_2−ZrO_2. C_8−C_1_4 alkanes of 55.8% was obtained over the optimized 1 wt%Pt/SiO_2−ZrO_2 due to its proper pore size of 9.0 nm and moderate acidic centers, together with more than 10% carbon yield of the oxygenated hydrocarbons, including C_1_1−C_1_3 chain alcohols & ketones and the hydrogenated F_2A dimers with furan ring (H-F_2A dimers). To improve the liquid alkane yield, a two-step process for F_2A conversion was also investigated, which included low-temperature hydrogenation at 50 °C over Raney Ni catalyst in a batch reactor and the subsequent high-temperature hydrodeoxygenation (HDO) at 280 °C over 1 wt%Pt/SiO_2−ZrO_2 in a fixed-bed reactor. The selectivity of 1,5-di(tetrahydro-2-furanyl)-3-pentanol (II-c) was the highest of 83.0% among the hydrogenated intermediates of H-F_2A dimers due to the protonation effect of methanol as the solvent and the hydrogenation of C=C bonds by Ni active centers. In the same time, the high content of this saturated alcohol H-dimer of II-C increased the solubility and stability of the intermediates in methanol solvent. High carbon yield of C_8−C_1_4 alkanes of 82.9%(mol) was obtained after oxygen atom removal from H-F_2A dimers via

Hydrogen for automotive applications and beyond

Energy Technology Data Exchange (ETDEWEB)

Eberle, U. [Adam Opel GmbH, Ruesselsheim (Germany)

2010-12-30

The energy storage system is of decisive importance for all types of electric vehicles, in contrast to the case of vehicles powered by a conventional fossil fuel or bio-fuel based internal combustion engine. Two major alternatives exist and need to be discussed: on the one hand, there is the possibility of electrical energy storage using batteries, whilst on the other hand there is the storage of energy in chemical form as hydrogen and the application of a fuel cell as energy converter. Considering the latter concept, hydrogen is a promising energy carrier in future energy systems. However, storage of hydrogen is a substantial challenge, especially for applications in vehicles with fuel cells that use proton-exchange membranes (PEMs). Different methods for hydrogen storage are discussed, including high-pressure and cryogenic-liquid storage, adsorptive storage on high-surface-area adsorbents, chemical storage in metal hydrides and complex hydrides, and storage in boranes. For the latter chemical solutions, reversible options and hydrolytic release of hydrogen with off-board regeneration are both possible. Reforming of liquid hydrogen-containing compounds is also a possible means of hydrogen generation. The advantages and disadvantages of the different systems are compared. (orig.)

PENGARUH JUMLAH ANGGOTA, VOLUME USAHA DAN LIKUIDITAS KOPERASI TERHADAP PERMINTAAN JASA AUDIT

Directory of Open Access Journals (Sweden)

Nanik Sri Utaminingsih

2012-03-01

Full Text Available Kebutuhan akan laporan keuangan yang bisa dipercaya sangatlah penting untuk mengambil keputusan. Permasalahan dari penelitian ini adalah apakah jumlah anggota, volume bisnis dan likuiditas secara parsial dan simultan mempengaruhi permintaan jasa audit. Populasi dalam penelitian ini adalah 765 koperasi dan sampelnya berjumlah 89 koperasi. Data yang digunakan adalah laporan keuangan koperasi pada tahun fiscal 2008. Data analisis yang digunakan adalah analisis deskriptif, multikolnearitas and logistic regression. Kesimpulan dari penelitian ini adalah variabel jumlah anggota dan likuiditas mempengaruhi permintaan jasa audit secara parsial sedangkan volume bisnis tidak mempengaruhi permintaan jasa audit. Secara simultan 3 variabel mempengaruhi permintaan jasa audit. The need for reliable financial statements, and can be trusted is necessary in making a decision. The problem in this study is whether which the number of members, the business volume and liquidity partially and simultaneously affect the demand for audit services. The population in this study were 765 cooperatives and the research sample is 89 cooperatives. The dependent variables in this study are demand audit services. While the independent variables are the number of members, the business vo-lume and liquidity of cooperatives. The data used in the form of cooperative financial reports, fiscal year 2008  with using descriptive analysis, multicolonearitas and logistic regression. The conclusion of this research is variable number of members, and liquidity, the partial affect on demand for audit services, while business volume is partially not influence the audit services. Simultaneously, the three indepen-dent variables influenced the demand for audit services.

Light exotic atoms in liquid and gaseous hydrogen and deuterium. Atom anti pp, theory and experiment

International Nuclear Information System (INIS)

Markushin, V.E.

1980-01-01

Considered are the de-eXcitation, absorption and Stark mixing processes in light exotic atoms formed in liquid and gaseous hydrogen (deuteriUm) and presented is the new method of the cascade calculations. Atom anti pp is studied in detail, calculated are: the populations of atomic levels, the absorption probabilities, and the X-rays yields. The present-day experimental data are discussed and it is concluded that all of them (but one result), can be easily reconciled with each other and with the theory

Caractérisation de quelques stabilisants naturels de l'émulsion d'eau dans le pétrole brut, grace à l'extension de la technique de "moussage" au système liquide-liquide eau-huile Characterising Several Natural Stabilizants of Water Emulsion in Crude Oil by Extending the "Foaming" Technique to Oil/Water Liquid-Liquid Systems

Directory of Open Access Journals (Sweden)

Coste J. -F.

2006-11-01

Full Text Available L'extension de la technique, de " moussage "au système liquide-liquide eau-pétrole brut a permis d'augmenter la concentration d'une fraction du pétrole en acides naphténiques, amines, asphaltènes et porphyrines, grâce à l'accroissement de l'aire de l'interface entre les deux phases non miscibles. Ces espèces chimiques présentes à l'interface favorisent la formation des films entre les gouttelettes de phase aqueuse dispersée. Elles sont à l'origine de la stabilité de I'émulsion d'eau dans le pétrole. The " foaming " technique was extended to a water/crude-oil liquid-liquid system so as to increase the concentration of naphthenic acids, amines, asphaltenes and porphyrins in an oil fraction by enlarging the interface orea between the two immiscible phases. The presence of these chemical species at the interface promotes the formation of films between the dispersed aqueuss-phase droplets. They are at the origin of the stability of a water in oil emulsion.

Developing a Model Using Homer for a Hybrid Hydrogen Fuel Cell System

Directory of Open Access Journals (Sweden)

Fera Annisa

2013-04-01

Full Text Available ABSTRACT. Hydrogen is widely considered be the fuel of the near future. Combined wind/PV energy hybrid systems can be used to sources energy to hydrogen production. This paper describes design, simulation and feasibility study of a hybrid energy system for a household in Malaysia. One year recorded wind speed and solar radiation are used for the design of a hybrid energy system. In 2000 was average annual wind speed in Johor Bahru is 3.76 m/s and annual average solar energy resource available is 5.08 kWh/m2/day. National Renewable Energy Laboratory’s HOMER software was used to select an optimum hybrid energy system. In the optimization process, HOMER simulates every system configuration in the search space and displays the feasible ones in a table, sorted by total net present cost (TNPC. The optimization study indicates that sensitivity analysis of the HOMER is shown in the overall winner which shows that the most least cost and optimize hybrid system is combination of 10 kW of PV array, 1 unit of wind turbine, 2 kW of fuel cell, 120 units of batteries and 6 kW converter as well as 1 kW of electrolyzer so as to generate the minimum COE, $2.423 kWh- 1. Although renewable sources (wind and PV involved in the power generation, 1 kg of hydrogen was produced in this system. Pengembangan Model Dengan Menggunakan Homer Untuk Sistem Sel Berbahan bakar Hidrogen Hibrida ABSTRAK. Hidrogen secara luas dianggap sebagai bahan bakar masa depan. Gabungan sistem hibrida energi angin/fotovoltaik dapat digunakan untuk sumber energi produksi hidrogen. Makalah ini menjelaskan desain, simulasi dan studi kelayakan dari sistem energi hibrida untuk rumah tangga di Malaysia. Satu tahun kecepatan angin tercatat dan radiasi matahari digunakan untuk desain sistem energi hibrida. Pada tahun 2000 adalah kecepatan angin rata-rata tahunan di Johor Bahru 3.76 m/det dan rata-rata sumber daya energi surya tahunan yang tersedia adalah 5.08 kWjam/m2/ hari. Software HOMER digunakan

Composition of hydrogenation products of Borodino brown coal

Energy Technology Data Exchange (ETDEWEB)

M.A. Gyul' malieva; A.S. Maloletnev; G.A. Kalabin; A.M. Gyul' maliev [Institute for Fossil Fuels, Moscow (Russian Federation)

2008-02-15

The composition of liquid products of hydrogenation of brown coal from the Borodino deposit was determined by means of {sup 13}C NMR spectroscopy and chemical thermodynamics methods. It was shown that the group composition of the liquid hydrogenation products at thermodynamic equilibrium is predictable from the elemental composition of the organic matter of parent coal. 9 refs., 5 figs., 6 tabs.

EKSTRAKSI ASAM SITRAT DAN ASAM OKSALAT : PENGARUH TRIOCTYLAMINE SEBAGAI EXTRACTING POWER DALAM BERBAGAI SOLVEN CAMPURAN TERHADAP KOEFISIEN DISTRIBUSI

Directory of Open Access Journals (Sweden)

Mega Kasmiyatun

2012-01-01

Full Text Available Generally, liquid waste of citric acid industry containing a highly citric acid, oxalic acid, due to precipitation process of calcium citrate less completely. Liquid-liquid extraction process is this one alternative that used to recover citric acid and oxalic acid, either in the product separation process from the fermentor or the treatment of its liquid waste. In order to understand, that the extraction process can be applied both technically and economically, it needs a more study the extraction parameters. The investigation has carried out about study of the extraction of citric acid and oxalic acid used trioctyl-amine as extracting power on various mix solvent and its ratio, related to the distribution coefficient. Extraction used a separating funnel that it was shaked with using an automatic shaker, which adjusted on specific velocity during 2.5 hours. The rafinate and extract were separated by separating funnel, then they were analyzed both concentration of citric acid and oxalic acid using a high performance liquid chromatography (HPLC. The results of the research show that the mixed solvent (consist of 15% trioctyl amine, 70% dodecane, and 15% hexanol, for the extraction of citric acid  produce both the highest distribution coefficient and percentage of separation were 1.15 and 74.22%, respectively; and this were achieved for the ratio between the solvent and diluent of 2.5:1. For the extraction of oxalic acid similar result were obtained, and the value were 3.78 and 88.31%, respectively, for the ratio between solvent and diluent of 2:1.Limbah cair pabrik asam sitrat pada umumnya mengandung asam sitrat, asam oksalat, cukup tinggi akibat proses pengendapan calsium sitrat yang kurang sempurna. Proses ekstraksi cair-cair adalah salah satu alternatif yang dapat digunakan untuk pengambilan kembali asam sitrat dan asam oksalat, baik pada proses pemisahan produk yang keluar dari fermentor maupun pada proses pengolahan limbah cairnya. Untuk

Latent hazard related to a hydrogen liquefaction installation

International Nuclear Information System (INIS)

Spoendlin, R.

1961-01-01

In this note, the author reports an attempt of analysis of hazards which could be related to a hydrogen liquefaction installation in order to identify the most appropriate safety measures. In order to do so, experiments have been performed on electrostatic charges born by solid crystals in liquid hydrogen, and explosion tests have been performed on a mixture of solid oxygen and liquid hydrogen. Moreover, the author tried to analyse accidents which occurred in this field by performing a survey among scientists working in laboratories in different countries

Metal nanoparticles/ionic liquid/cellulose: polymeric membrane for hydrogenation reactions

Directory of Open Access Journals (Sweden)

Marcos Alexandre Gelesky

2014-01-01

Full Text Available Rhodium and platinum nanoparticles were supported in polymeric membranes with 10, 20 and 40 µm thickness. The polymeric membranes were prepared combining cellulose acetate and the ionic liquid (IL 1-n-butyl-3-methylimidazolium bis(trifluoromethane sulfonylimide (BMI.(NTf2. The presence of metal nanoparticles induced an increase in the polymeric membrane surface areas. The increase of the IL content resulted in an improvement of elasticity and decrease in tenacity and toughness, whereas the stress at break was not affected. The presence of IL probably causes an increase in the separation between the cellulose molecules that result in a higher flexibility and processability of the polymeric membrane. The CA/IL/M(0 combinations exhibit an excellent synergistic effect that enhances the activity and durability of the catalyst for the hydrogenation of cyclohexene. The CA/IL/M(0 polymeric membrane displays higher catalytic activity (up to 7.353 h-1 for the 20 mm of CA/IL/Pt(0 and stability than the nanoparticles dispersed only in the IL.

Azobenzene dye-coupled quadruply hydrogen-bonding modules as colorimetric indicators for supramolecular interactions

Directory of Open Access Journals (Sweden)

Yagang Zhang

2012-04-01

Full Text Available The facile coupling of azobenzene dyes to the quadruply hydrogen-bonding modules 2,7-diamido-1,8-naphthyridine (DAN and 7-deazaguanine urea (DeUG is described. The coupling of azobenzene dye 2 to mono-amido DAN units 4, 7, and 9 was effected by classic 4-(dimethylaminopyridine (DMAP-catalyzed peptide synthesis with N-(3-dimethylaminopropyl-N’-ethyl carbodiimide hydrochloride (EDC as activating agent, affording the respective amide products 5, 8, and 10 in 60–71% yield. The amide linkage was formed through either the aliphatic or aromatic ester group of 2, allowing both the flexibility and absorption maximum to be tuned. Azobenzene dye 1 was coupled to the DeUG unit 11 by Steglich esterification to afford the product amide 12 in 35% yield. Alternatively, azobenzene dye 16 underwent a room-temperature copper-catalyzed azide–alkyne Huisgen cycloaddition with DeUG alkyne 17 to give triazole 18 in 71% yield. Azobenzene coupled DAN modules 5, 8, and 10 are bright orange–red in color, and azobenzene coupled DeUG modules 12 and 18 are orange–yellow in color. Azobenzene coupled DAN and DeUG modules were successfully used as colorimetric indicators for specific DAN–DeUG and DAN–UPy (2-ureido-4(1H-pyrimidone quadruply hydrogen-bonding interactions.

Safe production and application of hydrogen at Munich airport

Energy Technology Data Exchange (ETDEWEB)

Szamer, R.

2005-07-01

At Munich International Airport the world's first public filling station for liquid and gaseous hydrogen with on-site hydrogen gas production has been installed. In order to prove the safety, liability and economic feasibility of hydrogen this pilot project examined the complete sequence of hydrogen production and application: on-site production with pressurized electrolyser and steam reformer, storage and filling of gaseous and liquid hydrogen, application of hydrogen for propelling several vehicles, e.g. airport busses in day to day operation, cars, fork lifter. TUV SUD Group, one of the largest service provider for technical safety and quality, was involved in the safety evaluation of the hydrogen project from the very beginning with the following services: safety consultancy throughout all project phases, e.g. for licensing procedures, plant design and operation safety analysis of the overall plant and of subsystems (electrolyser, filling stations, storage tanks, control systems etc.) safety assessment and acceptance testing of CH2 busses, CH2 fork lifter and LH2 passenger cars inspections and tests The challenges of this complex project relating to safety will be presented in the lecture, e.g. identification of potential hazards, safety requirements for the design and operation of the hydrogen plant as wells as for the various applications. Project description The hydrogen plant (cf. Figure 1) comprises two supply paths, one for compressed gaseous hydrogen (CH2) and one for cryogenic liquid hydrogen. Gaseous hydrogen is produced via high-pressure electrolysis at an operating pressure of 3 MPa (30 bar) and/or steam reforming process. The hydrogen will be led into a compressor, compressed to 35 MPa (350 bar) and stored in high pressure cylinders with a total geometrical storage volume of 10 m. The cylinders supply the high-pressure filling stations which refuels the 3 hydrogen buses and the fork lifter. Liquid hydrogen (LH2) is delivered in tank trucks and

Microstructure and hydrogen bonding in water-acetonitrile mixtures.

Science.gov (United States)

Mountain, Raymond D

2010-12-16

The connection of hydrogen bonding between water and acetonitrile in determining the microheterogeneity of the liquid mixture is examined using NPT molecular dynamics simulations. Mixtures for six, rigid, three-site models for acetonitrile and one water model (SPC/E) were simulated to determine the amount of water-acetonitrile hydrogen bonding. Only one of the six acetonitrile models (TraPPE-UA) was able to reproduce both the liquid density and the experimental estimates of hydrogen bonding derived from Raman scattering of the CN stretch band or from NMR quadrupole relaxation measurements. A simple modification of the acetonitrile model parameters for the models that provided poor estimates produced hydrogen-bonding results consistent with experiments for two of the models. Of these, only one of the modified models also accurately determined the density of the mixtures. The self-diffusion coefficient of liquid acetonitrile provided a final winnowing of the modified model and the successful, unmodified model. The unmodified model is provisionally recommended for simulations of water-acetonitrile mixtures.

Adsorption methods for hydrogen isotope storage on zeolitic sieves

International Nuclear Information System (INIS)

Cristescu, Ioana; Cristescu, Ion; Vasut, F.; Brad, S.; Lazar, A.

2001-01-01

For hydrogen isotope separation, adsorption molecular sieves and active carbon were used. Adsorption process proceeds at liquid nitrogen and liquid hydrogen temperatures. Commercial zeolites have the same proprieties with natural zeolites, but they have a regular pore structure. They also have affinity for molecules of different size with defined shapes. Experimental results obtained at liquid nitrogen temperature (77.4 K) and liquid hydrogen revealed the efficient behaviour of the active carbon and zeolitic sieves for hydrogen isotopes temporary storage. We study adsorption of the synthetic zeolites in a wide range of temperatures and pressures and we used the molecular sieves 4A, 5A and active carbon. The 4A and 5A zeolites have a tridimensional structure with 11.4 A diameter. When the hydration water is eliminated, the material keeps a porous structure. The porous volume represents 45% from the zeolite mass for 4A and 5A sieves. The activation temperature of the zeolite and the carbon is very important for obtaining a high adsorption capacity. If the temperature used for activation is low, the structural water will be not eliminated and the adsorption capacity will be low. The excessive temperature will destroy the porous structure. The adsorption capacity for the hydrogen isotopes was calculated with the relation: A = V ads /m (cm 3 /g). The adsorption capacity and efficiency for the adsorbent materials, are given. Physical adsorption process of the hydrogen isotopes was carried out at liquid nitrogen temperature. The flux gas used in the adsorption system is composed of dry deuterium and protium. This mixture is cooled in liquid nitrogen and then is passed to the adsorbent getter at the same temperature (77.4 K). The gas flux in the adsorbent getter is 5 and 72 l/h (which correspond to 0.008 and 0.134 discharge velocity, respectively). (authors)

Magnetic refrigerator for hydrogen liquefaction

Energy Technology Data Exchange (ETDEWEB)

Numazawa, T [National Institute for Materials Science, Tsukuba (Japan); Kamlya, K. [Japan Atomic Energy Agency, Naka (Japan); Utaki, T. [Osaka University, Osaka (Japan); Matsumoto, K. [Kanazawa University, Kanazawa (Japan)

2013-06-15

This paper reviews the development status of magnetic refrigeration system for hydrogen liquefaction. There is no doubt that hydrogen is one of most important energy sources in the near future. In particular, liquid hydrogen can be utilized for infrastructure construction consisting of storage and transportation. Liquid hydrogen is in cryogenic temperatures and therefore high efficient liquefaction method must be studied. Magnetic refrigeration which uses the magneto-caloric effect has potential to realize not only the higher liquefaction efficiency > 50 %, but also to be environmentally friendly and cost effective. Our hydrogen magnetic refrigeration system consists of Carnot cycle for liquefaction stage and AMR (active magnetic regenerator) cycle for precooling stages. For the Carnot cycle, we develop the high efficient system > 80 % liquefaction efficiency by using the heat pipe. For the AMR cycle, we studied two kinds of displacer systems, which transferred the working fluid. We confirmed the AMR effect with the cooling temperature span of 12 K for 1.8 T of the magnetic field and 6 second of the cycle. By using the simulation, we estimate the total efficiency of the hydrogen liquefaction plant for 10 kg/day. A FOM of 0.47 is obtained in the magnetic refrigeration system operation temperature between 20 K and 77 K including LN2 work input.

Pembuatan Pasta Gigi Katekin Teh Hijau dan Uji Daya Hambat terhadap Bakteri Streptococcus Mutans dan Lactobascillus Ascidopillus

Directory of Open Access Journals (Sweden)

Fajriani Fajriani

2015-06-01

Peracikan formula dan pembuatan pasta gigi katekin teh hijau dilakukan sesuai hasil uji KHM (MIC. Pasta gigi katekin teh hijau ini dilakukan pengukuran kadar total flavonoid dan total polifenol, selanjutnya pengukuran uji daya hambat pasta gigi katekin teh hijau dilakukan dengan metode difusi menggunakan well (sumuran sebagai reservoar sampel uji terhadap bakteri streptococus mutans dan lactobacilus acidophilus. Hasil diperoleh prodak pasta gigi katekin teh hijau dengan kandungan kadar flavonoid 77% dan kadar polifenol 41%, sedangkan hasil uji diameter hambatan pasta gigi katekin teh hijau terhadap bakteri streptococcus mutans 17,2 mm dan bakteri lactobacillus acidophilus 19,6 mm. Hasil ini menunjukkan bahwa prodak katekin teh hijau ini sangat efektif digunakan sehari-hari sebagai perawatan gigi dan juga sebagai antibakteri kariogenik.   Making Green Tea Catechin Toothpaste and Inhibition Test Against Streptococcus Mutans and Acidophilus Lactobaccilus. The manufacture of this toothpaste is motivated by the desire of researchers to facilitate the public to use natural ingredients of green tea catechins whose result effectiveness against cariogenic bacteria was directly tested inhibition. This study is to find the right formula composition for greentea catechins toothpaste based on the result of the inhibition properties of greentea cathecins against tostreptococcus mutans dan lactobacillus acidophilus. The manufacture of greentea catechins toothpaste was after making catechins extracts and testing minimal inhibition concentration (MIC and minimal bactericidal concentration (MBC using liquid dilution method. The toothpaste was then made according to the result of MIC. The toothpaste’s flavonoid and polyphenol total contain was measured; then the inhibition property of the toothpaste to was measured using diffusion method with wells as the sample reservoar for streptococus mutans dan lactobacilus acidophilus. It is found that the toothpaste contains

Hydrogen - A new green energy

International Nuclear Information System (INIS)

Barnu, Franck

2013-01-01

A set of articles proposes an overview of the role hydrogen might have as energy in the energy transition policy, a review of different areas of research related to the hydrogen sector, and presentations of some remarkable innovations in different specific fields. Hydrogen might be an asset in energy transition because production modes (like electrolysis) result in an almost carbon-free or at least low-carbon hydrogen production. Challenges and perspectives are evoked: energy storage for intermittent energies (the MYRTE platform), the use of a hydrogen-natural mix (GRHYD program), the development of fuel cells for transport applications, and co-generation (Japan is the leader). Different French research organisations are working on different aspects and areas: the H2E program by Air Liquide, fuel cell technologies by GDF Suez, power electrolyzers and cells by Areva. Some aspects and research areas are more specifically detailed: high temperature electrolysis (higher efficiencies, synthesis of methane from hydrogen), fuel cells (using less platinum, and using ceramics for high temperatures), the perspective of solid storage solutions (hydrogen bottles in composite materials, development of 'hydrogen sponges', search for new hydrides). Innovations concern a project car, storage and production (Greenergy Box), the McPhy Energy storage system, an electric bicycle with fuel cell, easy to transport storage means by Air Liquide and Composites Aquitaine, development of energy autonomy, fuel cells for cars, electrolyzers using the Proton Exchange Membrane or PEM technology

Hydrogen production from coal using a nuclear heat source

International Nuclear Information System (INIS)

Quade, R.N.

1977-01-01

A strong candidate for hydrogen production in the intermediate time frame of 1990 to 1995 is a coal-based process using a high-temperature gas-cooled reactor (HTGR) as a heat source. Expected process efficiencies in the range of 60 to 70% are considerably higher than all other hydrogen production processes except steam reforming of a natural gas - a feedstock which may not be available in large quantities in this time frame. The process involves the preparation of a coal liquid, hydrogasification of that liquid, and steam reforming of the resulting gaseous or light liquid product. Bench-scale experimental work on the hydrogasification of coal liquids is being carried out. A study showing process efficiency and cost of hydrogen vs nuclear reactor core outlet temperature has been completed and shows diminishing returns at process temperatures above about 1500 0 F. (author)

KEBIJAKAN DALAM PENENTUAN DAN PENDANAAN MODAL KERJA PERUSAHAAN

Directory of Open Access Journals (Sweden)

Miswanto Miswanto

2012-10-01

Full Text Available Abstract: Policy in Determining and Financing Company’s Working Capital. In funding working capital, a company can use hedging policy, conservative policy, and aggressive policy. In relation to long-term versus short-term financing, temporary versus permanent current assets, and the trade-off between risk and profitability, it can be concluded that when the temporary current assets are financed by short-term financing they have moderate risk and profitability, when the temporary current assets are financed by long-term financing they have low risk and profitability, when the permanent current assets are financed by short-term funding they have high risk and profitability, and when the permanent current assets are financed by long-term financing they have moderate risk-profitability. To measure the performance of the working capital management, the working capital position of the company needs to be analyzed. By using the data presented on the balance sheet and income statement, the company can carry out the analysis of working capital performance using financial ratio analysis on working capital, analysis of the funding sources and use of funding statement, and analysis of the company's cash flow statement. Keywords: liquidity, capital, financing, profitability, and risk   Abstrak: Kebijakan dalam Penentuan dan Pendanaan Modal Kerja Perusahaan. Dalam mendanai modal kerja, perusahaan dapat menggunakan kebijakan hedging, kebijakan konservatif, dan kebijakan agresif. Dalam hubungannya antara pendanaan jangka pendek versus jangka panjang, aktiva lancar temporer versus permanen, dan trade-off antara risiko dan profitabilitas diperoleh kesimpulan bahwa jika aktiva lancar temporer dibiayai dengan pendanaan jangka pendek memiliki risiko dan profitabilitas moderat, jika aktiva lancar temporer dibiayai dengan pendanaan jangka panjang memiliki risiko dan profitabilitas rendah, jika aktiva lancar permanen dibiayai dengan pendanaan jangka pendek memiliki

On the vapor-liquid equilibrium in hydroprocessing reactors

Energy Technology Data Exchange (ETDEWEB)

Chen, J.; Munteanu, M.; Farooqi, H. [National Centre for Upgrading Technology, Devon, AB (Canada)

2009-07-01

When petroleum distillates undergo hydrotreating and hydrocracking, the feedstock and hydrogen pass through trickle-bed catalytic reactors at high temperatures and pressures with large hydrogen flow. As such, the oil is partially vaporized and the hydrogen is partially dissolved in liquid to form a vapor-liquid equilibrium (VLE) system with both vapor and liquid phases containing oil and hydrogen. This may result in considerable changes in flow rates, physical properties and chemical compositions of both phases. Flow dynamics, mass transfer, heat transfer and reaction kinetics may also be modified. Experimental observations of VLE behaviours in distillates with different feedstocks under a range of operating conditions were presented. In addition, VLE was predicted along with its effects on distillates in pilot and commercial scale plants. tabs., figs.

Seasonal storage and alternative carriers: A flexible hydrogen supply chain model

International Nuclear Information System (INIS)

Reuß, M.; Grube, T.; Robinius, M.; Preuster, P.; Wasserscheid, P.; Stolten, D.

2017-01-01

Highlights: •Techno-economic model of future hydrogen supply chains. •Implementation of liquid organic hydrogen carriers into a hydrogen mobility analysis. •Consideration of large-scale seasonal storage for fluctuating renewable hydrogen production. •Implementation of different technologies for hydrogen storage and transportation. -- Abstract: A viable hydrogen infrastructure is one of the main challenges for fuel cells in mobile applications. Several studies have investigated the most cost-efficient hydrogen supply chain structure, with a focus on hydrogen transportation. However, supply chain models based on hydrogen produced by electrolysis require additional seasonal hydrogen storage capacity to close the gap between fluctuation in renewable generation from surplus electricity and fuelling station demand. To address this issue, we developed a model that draws on and extends approaches in the literature with respect to long-term storage. Thus, we analyse Liquid Organic Hydrogen Carriers (LOHC) and show their potential impact on future hydrogen mobility. We demonstrate that LOHC-based pathways are highly promising especially for smaller-scale hydrogen demand and if storage in salt caverns remains uncompetitive, but emit more greenhouse gases (GHG) than other gaseous or hydrogen ones. Liquid hydrogen as a seasonal storage medium offers no advantage compared to LOHC or cavern storage since lower electricity prices for flexible operation cannot balance the investment costs of liquefaction plants. A well-to-wheel analysis indicates that all investigated pathways have less than 30% GHG-emissions compared to conventional fossil fuel pathways within a European framework.

Etude d'un procédé d'hydroliquéfaction du charbon pour la production simultanée de gaz et de carburant . . . . . Studies of a Coal Hydrogenation Process to Produce CO-Currently Gas and Gasoline

Directory of Open Access Journals (Sweden)

Franckowiak S.

2006-11-01

Full Text Available Un des principaux moyens de réintroduire le charbon dans le marché énergétique français est de le transformer en produits utiles comme le gaz de réseau ou les carburants. Les procédés d'oxyvapogazéification permettent d'obtenir un gaz de synthèse qui peut être ensuite converti en gaz riche ou en produits liquides. L'hydrogénation en phase liquide (ou hydroliquéfaction se présente pour le long terme comme une seconde voie qui offre des avantages spécifiques - taux de conversion du charbon et rendement élevés, - production directe de gaz de substitution (GNS et de carburant, - possibilité d'utilisation d'hydrogène provenant de l'électricité nucléaire. Un programme d'étude a été lancé avec la participation du Gaz de France (GDF, du Centre d'études et de recherches des Charbonnages de France (Cerchar, de l'institut Français du Pétrole (lFP et du Centre National de la Recherche Scientifique (CNRS dans le cadre du Groupe d'Étude de la Conversion du Charbon par Hydrogénation (GECH. Un banc d'essai d'hydroliquéfaction situé au Cerchar, d'un débit de 10 kg/h de mélange charbon-solvant, permet d'obtenir des hydrogénats dans des conditions variées et en présence de divers catalyseurs. L'étude de la valorisation de ces hydrogénats est effectuée dans les laboratoires de l'lFP. Les essais et les études effectués permettent d'envisager la production à volonté du GNS, de carburants ou des deux ensemble. Un modèle d'optimisation a été réalisé au GDF pour étudier et comparer les différentes filières en prenant en compte l'utilisation d'hydrogène d'électrolyse ou d'hydrogène produit sur place à partir du résidu de liquéfaction. One of the main ways to bring coal in the future french energy market is to transform it into valuable products. The oxygen steam gasification processes give a synthesis gas which can be converted into SNG or gasoline in a catalytic stage. The liquid phase hydrogenation process is a

Mechanical pumps for liquid metals; Pompes mecaniques pour metaux liquides

Energy Technology Data Exchange (ETDEWEB)

Baumier, J; Gollion, H J [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1964-07-01

The pumping of liquid metals by centrifugal pumps poses two principal problems. These are hermetic sealing of the rotating shaft and, its guidance where immersed in liquid metal. The solutions to the problems used on 13 experimental pumps are given here. The resolution of the guidance problem consists in the majority of cases in the utilisation of hydrostatic bearings. Accordingly, a theoretical study was instituted for the first time to calculate the bearings of the earlier pumps. After this, an experimental study was carried out, to check the theory by water tests. A relation for bearing calculation of pumps with diffusers is proposed. Finally the influence of the bearing elasticity on the shafts critical speed is studied. (authors) [French] Le pompage des metaux liquides, par des pompes centrifuges, pose 2 principaux problemes, qui sont: d'une part, la realisation d'une excellente etancheite au passage de l'arbre, d'autre part, son guidage sur la partie immergee dans le metal liquide. Les solutions retenues pour resoudre ces problemes sur 13 pompes experimentees sont presentees. Le probleme du guidage de l'arbre, a dans la majorite des cas ete resolu en utilisant un palier hydrostatique, aussi l'etude en a d'abord ete approfondie de facon theorique pour calculer les paliers des premieres pompes, puis experimentale pour controler la theorie, en effectuant des essais a l'eau. On propose une relation pour calculer les paliers des pompes a diffuseurs. On a en outre effectue une etude de l'influence de l'elasticite du palier hydrostatique sur la vitesse critique de l'arbre. (auteurs)

Energizing Engineering Students with Hydrogen Fuel Cell Project

Science.gov (United States)

Cannell, Nori; Zavaleta, Dan

2010-01-01

At Desert Vista High School, near Phoenix, Arizona, Perkins Innovation Grant funding is being used to fund a program that is helping to prepare students for careers in engineering by giving them hands-on experience in areas like hydrogen generation and fuel cell utilization. As one enters Dan Zavaleta's automotive and engineering classroom and lab…

Low temperature heat capacity measurements of the spin-liquid states of hydrogenated and deuterated κ-(BEDT-TTF)2Cu2(CN)3

International Nuclear Information System (INIS)

Yamashita, S.; Yamamoto, T.; Nakazawa, Y.

2010-01-01

Heat capacity measurements of organic triangular lattice compound κ-(BEDT-TTF) 2 Cu 2 (CN) 3 were performed to discuss the low energy excitations from the spin-liquid ground states. Existence of the T-linear electronic coefficient with finite electronic heat capacity coefficient γ was confirmed in three different samples from different batches, although small sample dependence was observed in the absolute values of the heat capacities. Concerning the sample in which hydrogen atoms in ethylene group in BEDT-TTF molecule have been substituted by deuterons, we have observed almost similar thermodynamic behavior as the hydrogenated sample. The absence of drastic change of electronic properties of this compound is consistent with the electronic phase diagram given by Kurosaki et al. [11] (Phys. Rev. Lett. 95 (2005) 17001). The obtained data are well consistent with the previous heat capacity experiments. The existence of the γ term demonstrates that the excitations from the quantum spin-liquid states show a gapless behavior at least down to 0.7 K.

Autothermal hydrogen storage and delivery systems

Science.gov (United States)

Pez, Guido Peter [Allentown, PA; Cooper, Alan Charles [Macungie, PA; Scott, Aaron Raymond [Allentown, PA

2011-08-23

Processes are provided for the storage and release of hydrogen by means of dehydrogenation of hydrogen carrier compositions where at least part of the heat of dehydrogenation is provided by a hydrogen-reversible selective oxidation of the carrier. Autothermal generation of hydrogen is achieved wherein sufficient heat is provided to sustain the at least partial endothermic dehydrogenation of the carrier at reaction temperature. The at least partially dehydrogenated and at least partially selectively oxidized liquid carrier is regenerated in a catalytic hydrogenation process where apart from an incidental employment of process heat, gaseous hydrogen is the primary source of reversibly contained hydrogen and the necessary reaction energy.

Kandungan Komponen Fenolat, Kadar Fenolat Total, dan Aktivitas Antioksidan Madu dari Beberapa Daerah di Jawa dan Sumatera

Directory of Open Access Journals (Sweden)

Ichda Chayati

2015-03-01

Full Text Available KANDUNGAN KOMPONEN FENOLAT, KADAR FENOLAT TOTAL, DAN AKTIVITAS ANTIOKSIDAN MADU DARI BEBERAPA DAERAH DI JAWA DAN SUMATERA Study of Phenolic Compounts, Total Phenolic, and Antioxidant Activities of Monofloral Honeys from Some Areas in Java and Sumatera ABSTRACT Background. Many diseases resulted from degenerative processess which can be inhibited by antioxidant systems. Honey is one of food with antioxidant activity. Objective. This study aims to investigate antioxidant activities of several types of monofloral honey from Java and Sumatera. Method. A laboratory experimental study, conducted on 4 types of floral honeys: coffee, palm trees, cottonwoods and rambutan. Determination of phenolic compounds was performed with High Performance Liquid Chromatography (HPLC and measurement of total phenolic contents performed with Folin-Ciocalteu’s reagent. Antioxidant activity was conducted in two ways, those were by 2.2-diphenyl-1-picrylhydrasyl (DPPH free radical scavenging method and linoleic acid peroxidation method using butylated hydroxytoluene(BHT as a standard. Data were analyzed using Analysis of varian (Anova and continued with Duncan’s multiple range test (DMRT. Result. Four types of Javanese and Sumateranese honeys contained some phenolic compounds. Those are chlorogenic acid, cafeic acid, ρ-coumaric acid, ferulic acid, pinobanksin, quercetin, luteolin, pinocembrin and chrysin while the dominant fenolic compound varies between honeys. Total phenolic contents from four types of honey were between 2.000 to 4.400 ppm. The highest phenolic content was in honey from cottonwoods, but the best antioxidant activity was found in honey from coffee. Antioxidant activities were found in honey which come from the following order: coffee, cottonwoods, palm trees, and rambutan honey. Antioxidant activities did not correlated with total phenolic content. Conclusion. Javanese and Sumateranese honey contained nine active substances that varies in total

Recovering volatile liquids

Energy Technology Data Exchange (ETDEWEB)

Bregeat, J H

1925-07-30

The products of hydrogenation of alicyclic compounds, such as terpenes, for example, pinene or oil of turpentine, are used as washing liquids for absorbing vapours of volatile liquids from gases, such as natural gases from petroliferous regions, gases from the distillation of coal, lignite, schist, peat, etc. or from the cracking of heavy oils. Other liquids such as tar oils vaseline oils, cresols, etc. may be added.

Metallic hydrogen research

International Nuclear Information System (INIS)

Burgess, T.J.; Hawke, R.S.

1978-01-01

Theoretical studies predict that molecular hydrogen can be converted to the metallic phase at very high density and pressure. These conditions were achieved by subjecting liquid hydrogen to isentropic compression in a magnetic-flux compression device. Hydrogen became electrically conducting at a density of about 1.06 g/cm 3 and a calculated pressure of about 2 Mbar. In the experimental device, a cylindrical liner, on implosion by high explosive, compresses a magnetic flux which in turn isentropically compresses a hydrogen sample; coaxial conical anvils prevent escape of the sample during compression. One anvil contains a coaxial cable that uses alumina ceramic as an insulator; this probe allows continuous measurement of the electrical conductivity of the hydrogen. A flash x-ray radiograph exposed during the experiment records the location of the sample-tube boundaries and permits calculation of the sample density. The theoretical underpinnings of the metallic transition of hydrogen are briefly summarized, and the experimental apparatus and technique, analytical methods, and results are described. 9 figures

Hydrogen fuel - Universal energy

Science.gov (United States)

Prince, A. G.; Burg, J. A.

The technology for the production, storage, transmission, and consumption of hydrogen as a fuel is surveyed, with the physical and chemical properties of hydrogen examined as they affect its use as a fuel. Sources of hydrogen production are described including synthesis from coal or natural gas, biomass conversion, thermochemical decomposition of water, and electrolysis of water, of these only electrolysis is considered economicially and technologically feasible in the near future. Methods of production of the large quantities of electricity required for the electrolysis of sea water are explored: fossil fuels, hydroelectric plants, nuclear fission, solar energy, wind power, geothermal energy, tidal power, wave motion, electrochemical concentration cells, and finally ocean thermal energy conversion (OTEC). The wind power and OTEC are considered in detail as the most feasible approaches. Techniques for transmission (by railcar or pipeline), storage (as liquid in underwater or underground tanks, as granular metal hydride, or as cryogenic liquid), and consumption (in fuel cells in conventional power plants, for home usage, for industrial furnaces, and for cars and aircraft) are analyzed. The safety problems of hydrogen as a universal fuel are discussed, noting that they are no greater than those for conventional fuels.

Capacitive density measurement for supercritical hydrogen

Science.gov (United States)

Funke, Th; Haberstroh, Ch; Szoucsek, K.; Schott, S.; Kunze, K.

2017-12-01

A new approach for automotive hydrogen storage systems is the so-called cryo-compressed hydrogen storage (CcH2). It has a potential for increased energy densities and thus bigger hydrogen amounts onboard, which is the main attractiveness for car manufacturers such as BMW. This system has further advantages in terms of safety, refueling and cooling potential. The current filling level measurement by means of pressure and temperature measurement and subsequent density calculation faces challenges especially in terms of precision. A promising alternative is the capacitive gauge. This measuring principle can determine the filling level of the CcH2 tank with significantly smaller tolerances. The measuring principle is based on different dielectric constants of gaseous and liquid hydrogen. These differences are successfully leveraged in liquid hydrogen storage systems (LH2). The present theoretical analysis shows that the dielectric values of CcH2 in the relevant operating range are comparable to LH2, thus achieving similarly good accuracy. The present work discusses embodiments and implementations for such a sensor in the CcH2 tank.

Towards a unified description of the hydrogen bond network of liquid water: A dynamics based approach

International Nuclear Information System (INIS)

Ozkanlar, Abdullah; Zhou, Tiecheng; Clark, Aurora E.

2014-01-01

The definition of a hydrogen bond (H-bond) is intimately related to the topological and dynamic properties of the hydrogen bond network within liquid water. The development of a universal H-bond definition for water is an active area of research as it would remove many ambiguities in the network properties that derive from the fixed definition employed to assign whether a water dimer is hydrogen bonded. This work investigates the impact that an electronic-structure based definition, an energetic, and a geometric definition of the H-bond has upon both topological and dynamic network behavior of simulated water. In each definition, the use of a cutoff (either geometric or energetic) to assign the presence of a H-bond leads to the formation of transiently bonded or broken dimers, which have been quantified within the simulation data. The relative concentration of transient species, and their duration, results in two of the three definitions sharing similarities in either topological or dynamic features (H-bond distribution, H-bond lifetime, etc.), however no two definitions exhibit similar behavior for both classes of network properties. In fact, two networks with similar local network topology (as indicated by similar average H-bonds) can have dramatically different global network topology (as indicated by the defect state distributions) and altered H-bond lifetimes. A dynamics based correction scheme is then used to remove artificially transient H-bonds and to repair artificially broken bonds within the network such that the corrected network exhibits the same structural and dynamic properties for two H-bond definitions (the properties of the third definition being significantly improved). The algorithm described represents a significant step forward in the development of a unified hydrogen bond network whose properties are independent of the original hydrogen bond definition that is employed

Hydrogen bond dynamics in bulk alcohols.

Science.gov (United States)

Shinokita, Keisuke; Cunha, Ana V; Jansen, Thomas L C; Pshenichnikov, Maxim S

2015-06-07

Hydrogen-bonded liquids play a significant role in numerous chemical and biological phenomena. In the past decade, impressive developments in multidimensional vibrational spectroscopy and combined molecular dynamics-quantum mechanical simulation have established many intriguing features of hydrogen bond dynamics in one of the fundamental solvents in nature, water. The next class of a hydrogen-bonded liquid--alcohols--has attracted much less attention. This is surprising given such important differences between water and alcohols as the imbalance between the number of hydrogen bonds, each molecule can accept (two) and donate (one) and the very presence of the hydrophobic group in alcohols. Here, we use polarization-resolved pump-probe and 2D infrared spectroscopy supported by extensive theoretical modeling to investigate hydrogen bond dynamics in methanol, ethanol, and isopropanol employing the OH stretching mode as a reporter. The sub-ps dynamics in alcohols are similar to those in water as they are determined by similar librational and hydrogen-bond stretch motions. However, lower density of hydrogen bond acceptors and donors in alcohols leads to the appearance of slow diffusion-controlled hydrogen bond exchange dynamics, which are essentially absent in water. We anticipate that the findings herein would have a potential impact on fundamental chemistry and biology as many processes in nature involve the interplay of hydrophobic and hydrophilic groups.

Ovonic Renewable Hydrogen (ORH) - low temperature hydrogen production from renewable fuels

International Nuclear Information System (INIS)

Reichman, B.; Mays, W.; Strebe, J.; Fetcenko, M.

2009-01-01

'Full text': ECD has developed a new technology to produce hydrogen from various organic matters. In this technology termed Ovonic Renewable Hydrogen (ORH), base material such as NaOH is used as a reactant to facilitate the reforming of the organic matters to hydrogen gas. This Base-Facilitated Reforming (BFR) process is a one-step process and has number of advantages over the conventional steam reforming and gasification processes including lower operation temperature and lower heat consumption. This paper will describe the ORH process and discuss its technological and economics advantages over the conventional hydrogen production processes. ORH process has been studied and demonstrated on variety of renewable fuels including liquid biofuels and solid biomass materials. Results of these studies will be presented. (author)

KARAKTERISTIK INTERAKSI MEMBRAN-FOULANT DAN FOULANT-FOULANT SEBAGAI DASAR PENGENDALIAN FOULING

Directory of Open Access Journals (Sweden)

Heru Susanto

2012-05-01

Full Text Available THE CHARACTERISTICS OF MEMBRANE-FOULANT AND FOULANT-FOULANT INTERACTIONS AS THE BASIS FOR CONTROL OF FOULING. Industrial membrane applications for solid liquid and liquid-liquid filtration are limited by fouling and concentration polarization. Because fouling significantly reduces the membrane performance and often changes the membrane selectivity, efforts to overcome the fouling problem are very important from practical applications point of view. This paper presents the basic knowledge required to control fouling and recent development in fouling control including the method developed by the author. Control of fouling can be done by (i commercial membrane modification (post modification by photo-graft polymerization, (ii modification by polymer blending during membrane manufacturing and (iii integration of a pretreatment into membrane processes. The results showed that all the developed methods can significantly reduce the resulting fouling; however, none of the method could totally remove the occurring fouling. The understanding of the membrane-foulant and foulant-foulant interactions is the key to success in control of fouling.Aplikasi teknologi membran untuk pemisahan padat cair di  berbagai industri dibatasi oleh peristiwa fouling yang menyebabkan penurunan laju produk dan perubahan selektifitas membran. Oleh karena itu, pengendalian fouling merupakan upaya yang mutlak harus dilakukan. Makalah ini mempresentasikan pengetahuan dasar yang diperlukan untuk pengendalian fouling dan perkembangan terkini dalam pengendalian fouling termasuk hasil-hasil yang telah dikembangkan oleh penulis. Pengendalian fouling dilakukan dengan (i modifikasi membran komersial (post modification menggunakan metode photo-grafting, (ii modifikasi dengan pencampuran polimer selama proses pembuatan (polymer blend dan (iii integrasi unit perlakuan awal (pre-treatment dengan proses membran. Hasil penelitian menunjukkan bahwa kesemua metode yang dikembangkan dapat

Composite high-pressure vessels for hydrogen storage in mobile application. Pt. 1 / Light weight composite cylinders for compressed hydrogen. Pt. 2 - custom made hydrogen storage tanks and vessels

Energy Technology Data Exchange (ETDEWEB)

Rasche, C. [MCS Cylinder Systems GmbH, Dinslaken (Germany)

2000-07-01

Recent developments on fuel cell technology demonstrated the feasibility of propelling vehicles by converting fuel directly into electricity. Fuel cells conveniently use either compressed (CGH{sub 2}) or liquid hydrogen (LH{sub 2}) or methanol as the fuel source from a tank. Mobile storage of these fuelling will become an urgent need as this technology will come into series production expected for 2010. Due to the requirements on mobile hydrogen storage and the energy losses in the hydrogen-to-application-chain, a light-weight and energetic qualities and minimise ist bulky nature. Mobile storage of hydrogen can be realised either at high pressure values (> 20 MPa) or at deep temperatures (<-253 C). CGH{sub 2}: In the last few years, the introduction of natural gas driven vehicles has seen the development of compact mobile pressurised gas tanks in principle, this storage technique is also applicable for the compressed storage of hydrogen at filling pressures of > 20 MPa. LH{sub 2} : Storing hydrogen or natural gases in general in the liquid phase is accomplished either by applying a overpressure or keeping it below the phase transition temperature at ambient pressure in super insulated devices. (orig.)

Forced convection of liquid hydrogen - part 2 - case of large temperature differences between the fluid and the wall - final report (cylindrical channel)

International Nuclear Information System (INIS)

Perroud, P.; Rebiere, J.

1964-01-01

Measurements have been performed in a smooth Inconel tube of 2 mm ID and 2.5 mm OD, electrically heated on 300 mm by Joule effect (AC) The liquid enters the test section subcooled at the constant temperature of 25 deg. K of average; then it is heated till, most-often, complete vaporization. The conditions are: inlet pressure (subcritical) 8 atm (a number of experiences have been made under supercritical pressure of 16 atm), mass velocity 11 to 115 g/cm 2 .s, heat flux density 9 to 385 W/cm 2 , wall temperature reaching 800 deg. K. The liquid hydrogen used was composed of about 60 per cent of para-hydrogen (the transformation para-ortho does not happen in the process). A flow model, connected with the wall temperatures observed, is established. In the region of two-phase flow, the wall temperature highly decreases and passes through a minimum just when the steam quality reaches unity. A correlation for the heat transfer coefficients is given, in the two-phase flow region (steam quality from 0 to 1) and in the region of homogeneous gaseous phase (Reynolds varying from 15 000 to 420 000). Comparison with former correlations is also given. In the mixed-phase region, head losses due to friction are negligible with the respect to the pressure drop due to the variation of momentum. This latter can be calculated with good approximation using one-dimensional model. The head losses in gaseous phase follows the classical laws. Physical properties of liquid hydrogen extracted from the most recent literature, are given in supplement. (authors) [fr

Hydrogen from catalytic reforming of biomass-derived hydrocarbons in liquid water

Science.gov (United States)

Cortright, R. D.; Davda, R. R.; Dumesic, J. A.

2002-08-01

Concerns about the depletion of fossil fuel reserves and the pollution caused by continuously increasing energy demands make hydrogen an attractive alternative energy source. Hydrogen is currently derived from nonrenewable natural gas and petroleum, but could in principle be generated from renewable resources such as biomass or water. However, efficient hydrogen production from water remains difficult and technologies for generating hydrogen from biomass, such as enzymatic decomposition of sugars, steam-reforming of bio-oils and gasification, suffer from low hydrogen production rates and/or complex processing requirements. Here we demonstrate that hydrogen can be produced from sugars and alcohols at temperatures near 500K in a single-reactor aqueous-phase reforming process using a platinum-based catalyst. We are able to convert glucose-which makes up the major energy reserves in plants and animals-to hydrogen and gaseous alkanes, with hydrogen constituting 50% of the products. We find that the selectivity for hydrogen production increases when we use molecules that are more reduced than sugars, with ethylene glycol and methanol being almost completely converted into hydrogen and carbon dioxide. These findings suggest that catalytic aqueous-phase reforming might prove useful for the generation of hydrogen-rich fuel gas from carbohydrates extracted from renewable biomass and biomass waste streams.

Experimental Set-Up for Evaluation of Electro-Magnetic Characteristics of High-Tc Superconductors Cooled by Liquid Hydrogen

OpenAIRE

Shirai, Yasuyuki; Hikawa, Kyosuke; Shiotsu, Masahiro; Tatsumoto, Hideki; Hata, Koichi; Kobayashi, Hiroaki; Nonaka, Satoshi; Naruo, Yoshihiro; Inatani, Yoshifumi

2013-01-01

Liquid hydrogen (LH2) has excellent properties as a coolant, such as large latent heat, low viscosity coefficient, etc. Not only MgB2 but also other high-Tc superconductors are expected to have excellent properties when cooled by LH2. It is necessary for a stability design of a high-Tc superconductor cooled by LH2 to make an electro-magnetic characteristic clear. However, due to the handling difficulties of LH2, there are only few papers on the properties of LH2-cooled superconductors, especi...

Hydrogen bonding intermolecular effect on electro-optical response of doped 6PCH nematic liquid crystal with some azo dyes

Science.gov (United States)

Kiani, S.; Zakerhamidi, M. S.; Tajalli, H.

2016-05-01

Previous studies on the electro-optical responses of dye-doped liquid crystal have shown that dopant material have a considerable effect on their electro-optical responses. Despite the studies carried out on electro-optical properties of dye-doped liquid crystal, no attention has been paid to study of the interaction and structural effects in this procedure. In this paper, linear dyes and with similar structure were selected as dopants. The only difference in used dyes is the functional groups in their tails. So, doping of these dyes into liquid crystals determines the influence of interaction type on electro-optical behaviours of the doped systems. Therefore, in this work, two aminoazobenzene (;A-dye;: hydrogen bond donor) and dimethyl-aminoazobenzene (;B-dye;) dyes with different compositional percentages in liquid crystal host were used. Electro-optical Kerr behaviour, the pre-transition temperature and third order nonlinear susceptibility were investigated. The obtained results effectively revealed that type of interactions between the dye and liquid crystal is determinative of behavioral difference of doped system, compared to pure liquid crystal. Also, pre-transitional behaviour and thereupon Kerr electro-optical responses were affected by formed interactions into doped systems. In other words, it will be shown that addition of any dopants in liquid crystal, regardless of the nature of interactions, cannot cause appropriate electro-optical responses. In fact, type of dye, nature of interactions between dopant and liquid crystalline host as well as concentration of dye are the key factors in selecting the appropriate liquid crystal and dopant dye.

C1 CHEMISTRY FOR THE PRODUCTION OF ULTRA-CLEAN LIQUID TRANSPORTATION FUELS AND HYDROGEN

Energy Technology Data Exchange (ETDEWEB)

Gerald P. Huffman

2003-09-30

The Consortium for Fossil Fuel Science (CFFS) is a research consortium with participants from the University of Kentucky, University of Pittsburgh, University of Utah, West Virginia University, and Auburn University. The CFFS is conducting a research program to develop C1 chemistry technology for the production of clean transportation fuel from resources such as coal and natural gas, which are more plentiful domestically than petroleum. The processes under development will convert feedstocks containing one carbon atom per molecular unit into ultra clean liquid transportation fuels (gasoline, diesel, and jet fuel) and hydrogen, which many believe will be the transportation fuel of the future. These feedstocks include synthesis gas, a mixture of carbon monoxide and hydrogen produced by coal gasification or reforming of natural gas, methane, methanol, carbon dioxide, and carbon monoxide. Some highlights of the results obtained during the first year of the current research contract are summarized as: (1) Terminal alkynes are an effective chain initiator for Fischer-Tropsch (FT) reactions, producing normal paraffins with C numbers {ge} to that of the added alkyne. (2) Significant improvement in the product distribution towards heavier hydrocarbons (C{sub 5} to C{sub 19}) was achieved in supercritical fluid (SCF) FT reactions compared to that of gas-phase reactions. (3) Xerogel and aerogel silica supported cobalt catalysts were successfully employed for FT synthesis. Selectivity for diesel range products increased with increasing Co content. (4) Silicoaluminophosphate (SAPO) molecular sieve catalysts have been developed for methanol to olefin conversion, producing value-added products such as ethylene and propylene. (5) Hybrid Pt-promoted tungstated and sulfated zirconia catalysts are very effective in cracking n-C{sub 36} to jet and diesel fuel; these catalysts will be tested for cracking of FT wax. (6) Methane, ethane, and propane are readily decomposed to pure

Symetrie en energie des spectres de l'onde de densite de charge dans le 2-hydrogene seleniure de niobium

Science.gov (United States)

Behmand, Behnaz

Les mecanismes qui menent a la supraconductivite dans les supraconducteurs a haute temperature critique sont encore aujourd'hui mal compris contrairement a ceux dans les supraconducteurs conventionnels. Dans les hauts-Tc, certaines modulations de la densite d'etats electroniques coexistant avec la phase supraconductrice ont ete observees, ce qui engendre des questionnements sur leur role dans la supraconductivite. En fait, plusieurs types de modulation de la densite d'etats electroniques existent, comme par exemple l'onde de densite de charge et l'onde de densite de paires. Ces deux modulations, d'origines differentes et mesurables avec la technique de spectroscopie par effet tunnel, peuvent etre differenciees avec une etude de leur symetrie. Ce memoire consistera donc a presenter l'etude de la symetrie de l'onde de densite de charge dans le 2H-NbSe2 qui est presente dans la phase supraconductrice a 300 mK. Par contre, certaines difficultes liees au principe de mesure, soit l'effet de normalisation, nuisent a l'identification de cette symetrie. La methode, pour contourner ce probleme sera alors l'element clef de ce travail.

Hydrogen as automotive fuel

International Nuclear Information System (INIS)

Dini, D.; Ciancia, A.; Pede, G.; Sglavo, V.; ENEA, Rome

1992-01-01

An assessment of the technical/economic feasibility of the use of hydrogen as an automotive fuel is made based on analyses of the following: the chemical- physical properties of hydrogen in relation to its use in internal combustion engines; the modifications necessary to adapt internal combustion engines to hydrogen use; hydrogen fuel injection systems - with water vapour injection, cryogenic injection, and the low or high pressure injection of hydrogen directly into the combustion chamber; the current commercialization status of hydrogen automotive fuels; energy efficiency ratings; environmental impacts; in-vehicle storage systems - involving the use of hydrides, high pressure systems and liquid hydrogen storage systems; performance in terms of pay-load ratio; autonomous operation; and operating costs. The paper concludes that, considering current costs for hydrogen fuel production, distribution and use, at present, the employment of hydrogen fuelled vehicles is feasible only in highly polluted urban environments where the innovative vehicle's air pollution abatement characteristics would justify its high operating costs as compared with those of conventional automotive alternatives

Ultrafast quenching of metals to liquid-helium temperatures - investigation of the low-temperature mobility of hydrogen in niobium

International Nuclear Information System (INIS)

Blanz, M.; Blocher, R.; Carstanjen, H.D.; Messer, R.; Plachke, D.; Seeger, A.

1989-01-01

A novel technique for ultrafast quenching from 300 K to 4.2 K has been developed. It employs a fast jet of liquid helium with a speed of about 10 2 m/s and allows us to quench metal samples in about 6 ms. This corresponds to a quenching rate of about 4.5x10 4 K/s, which exceeds that achievable by conventional quenching in liquid helium by more than one order of magnitude. The technique has been used for a resistometric study of the behaviour of hydrogen in niobium quenched-in from the α-phase by means of isochronal and isothermal annealing. Even in the low-temperature region below 20 K a considerable recovery of the resistivity has been found, which cannot be seen in conventional quenching experiments. (orig.)

Production of Hydrogen from Bio-ethanol

International Nuclear Information System (INIS)

Fabrice Giroudiere; Christophe Boyer; Stephane His; Robert Sanger; Kishore Doshi; Jijun Xu

2006-01-01

IFP and HyRadix are collaborating in the development of a new hydrogen production system from liquid feedstock such as bio-ethanol. Reducing greenhouse gas (GHG) emissions along with high hydrogen yield are the key objectives. Market application of the system will be hydrogen refueling stations as well as medium scale hydrogen consumers including the electronics, metals processing, and oils hydrogenation industries. The conversion of bio-ethanol to hydrogen will be performed within a co-developed process including an auto-thermal reformer working under pressure. The technology will produce high-purity hydrogen with ultralow CO content. The catalytic auto-thermal reforming technology combines the exothermic and endothermic reaction and leads to a highly efficient heat integration. The development strategy to reach a high hydrogen yield target with the bio-ethanol hydrogen generator is presented. (authors)

Tribo-characteristics of self-lubricating ball bearings for the LE-7 liquid hydrogen rocket-turbopump

Science.gov (United States)

Nosaka, Masataka; Oike, Mamoru; Kikuchi, Masataka; Kamijo, Kenjiro; Tajiri, Masanori

1993-07-01

The tribo characteristics of self-lubricating 40-mm-bore ball bearings with a retainer of glass cloth-polytetrafluoroethylene (PTFE) laminate, which has elliptical pockets with a large pocket clearance, were tested under thrust loads at speeds up to 50,000 rpm, 2 million DN, in liquid hydrogen (LH2) and in liquid nitrogen (LN2). During testing, the bearing torque, outer-race temperature, and electric resistance between the inner and outer races were monitored to verify the formation and rupture of a PTFE transfer film. Testing showed that the bearings having the elliptical retainer pockets were superior to the conventional bearings with circular pockets. It was determined that, at the maximum inner race spinning velocity of about 5 m/s, a PTFE transfer film could sustain the maximum Hertz stress, up to about 2000 N/sq mm, in LH2, without severe film rupture resulting in bearing seizure. In LN2, the critical load capacity of PTFE transfer film with bearing seizure was about 2700 N/sq mm.

Hydrogen retorting of oil shales from Eastern Canada

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E. (CANMET, Ottawa, Ontario (Canada)); Synnott, J.; Boorman, R.S.; Salter, R.S.

1984-04-01

The liquid production potential of thirty oil shale samples from Eastern Canada was determined by Fischer assay retort and pyrochem retort. For all shales, the presence of hydrogen during pyrochem retorting resulted in a significant increase in oil yields compared to Fischer assay yields. Ten oil shale samples were selected for detailed evaluation in the pyrochem retort in the presence of nitrogen and hydrogen. Besides increasing yields, the presence of hydrogen lowered the specific gravity of liquid products and the content of sulphur but increased the content of nitrogen. This was attributed to the stabilization of precursors to nitrogen compounds which prevented their polymerization. (J.H.K.)

Hydrogen. A small molecule with large impact

Energy Technology Data Exchange (ETDEWEB)

Gehrke, H.; Ruthardt, K.; Mathiak, J.; Roosen, C. [Uhde GmbH, Dortmund (Germany)

2010-12-30

The first section of the presentation will provide general information about hydrogen including physical data, natural abundance, production and consumption figures. This will be followed by detailed information about current industrial production routes for hydrogen. Main on-purpose production for hydrogen is by classical steam reforming (SR) of natural gas. A brief overview of most important steps in stream reforming is given including reforming section, CO conversion and gas purification. Also the use of heavier than methane feedstocks and refinery off-gases is discussed. Alternative routes for hydrogen production or production of synthesis gas are autothermal reforming (ATR) or partial oxidation (POX). Pros and Cons for each specific technology are given and discussed. Gasification, especially gasification of renewable feedstocks, is a further possibility to produce hydrogen or synthesis gas. New developments and current commercial processes are presented. Hydrogen from electrolysis plants has only a small share on the hydrogen production slate, but in some cases this hydrogen is a suitable feedstock for niche applications with future potential. Finally, production of hydrogen by solar power as a new route is discussed. The final section focuses on the use of hydrogen. Classical applications are hydrogenation reactions in refineries, like HDS, HDN, hydrocracking and hydrofinishing. But, with an increased demand for liquid fuels for transportation or power supply, hydrogen becomes a key player in future as an energy source. Use of hydrogen in synthesis gas for the production of liquid fuels via Fischer-Tropsch synthesis or coal liquefaction is discussed as well as use of pure hydrogen in fuel cells. Additional, new application for biomass-derived feedstocks are discussed. (orig.)

Hydrogen Fueling Station Using Thermal Compression: a techno-economic analysis

Energy Technology Data Exchange (ETDEWEB)

Kriha, Kenneth [Gas Technology Inst., Des Plaines, IL (United States); Petitpas, Guillaume [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Melchionda, Michael [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Soto, Herie [Shell, Houston TX (United States); Feng, Zhili [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wang, Yanli [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-11

The goal of this project was to demonstrate the technical and economic feasibility of using thermal compression to create the hydrogen pressure necessary to operate vehicle hydrogen fueling stations. The concept of utilizing the exergy within liquid hydrogen to build pressure rather than mechanical components such as compressors or cryogenic liquid pumps has several advantages. In theory, the compressor-less hydrogen station will have lower operating and maintenance costs because the compressors found in conventional stations require large amounts of electricity to run and are prone to mechanical breakdowns. The thermal compression station also utilizes some of the energy used to liquefy the hydrogen as work to build pressure, this is energy that in conventional stations is lost as heat to the environment.

Symmetric bi-pyridyl banana-shaped molecule and its intermolecular hydrogen bonding liquid-crystalline complexes

Science.gov (United States)

Sui, Dan; Hou, Qiufei; Chai, Jia; Ye, Ling; Zhao, Liyan; Li, Min; Jiang, Shimei

2008-11-01

A new symmetric bi-pyridyl banana-shaped molecule 1,3-phenylene diisonicotinate (PDI) was designed and synthesized. Its molecular structure was confirmed by FTIR, Elemental analysis and 1H NMR. X-ray crystallographic study reveals that there is an angle of approximate 118° among the centroids of the three rings (pyridyl-phenyl-pyridyl) in each PDI molecule indicating a desired banana shape. In addition, a series of liquid crystal complexes nBA:PDI:nBA induced by intermolecular hydrogen bonding between PDI (proton acceptor) and 4-alkoxybenzoic acids (nBA, proton donor) were synthesized and characterized. The mesomorphism properties and optical textures of the complex of nBA:PDI:nBA were investigated by differential scanning calorimetry, polarizing optical microscope and X-ray diffraction.

Large-Scale Liquid Hydrogen Testing of Variable Density Multilayer Insulation with a Foam Substrate

Science.gov (United States)

Martin, J. J.; Hastings, L.

2001-01-01

The multipurpose hydrogen test bed (MHTB), with an 18-cu m liquid hydrogen tank, was used to evaluate a combination foam/multilayer combination insulation (MLI) concept. The foam element (Isofoam SS-1171) insulates during ground hold/ascent flight, and allowed a dry nitrogen purge as opposed to the more complex/heavy helium purge subsystem normally required. The 45-layer MLI was designed for an on-orbit storage period of 45 days. Unique WI features include a variable layer density, larger but fewer double-aluminized Mylar perforations for ascent to orbit venting, and a commercially established roll-wrap installation process that reduced assembly man-hours and resulted in a roust, virtually seamless MLI. Insulation performance was measured during three test series. The spray-on foam insulation (SOFI) successfully prevented purge gas liquefaction within the MLI and resulted in the expected ground hold heat leak of 63 W/sq m. The orbit hold tests resulted in heat leaks of 0.085 and 0.22 W/sq m with warm boundary temperatures of 164 and 305 K, respectively. Compared to the best previously measured performance with a traditional MLI system, a 41-percent heat leak reduction with 25 fewer MLI layers was achieved. The MHTB MLI heat leak is half that calculated for a constant layer density MLI.

Double hydrogen bonded ferroelectric liquid crystals: A study of field induced transition (FiT)

Science.gov (United States)

Vijayakumar, V. N.; Madhu Mohan, M. L. N.

2009-12-01

A novel series of chiral hydrogen bonded liquid crystals have been isolated. Hydrogen bond was formed between chiral nonmesogen ingredient levo tartaric acid and mesogenic p-n-alkoxybenzoic acids. Phase diagram was constructed from the transition temperatures obtained by DSC and polarizing optical microscopic (POM) studies. Thermal and electrical properties exhibited by three complexes namely LTA+8BA, LTA+7BA and LTA+5BA were discussed. Salient feature of the present work was the observation of a reentrant smectic ordering in LTA+8BA complex designated as C r∗ phase. This reentrant phenomenon was confirmed by DSC thermograms, optical textures of POM and temperature variation of capacitance and dielectric loss studies. Tilt angle was measured in smectic C ∗ and reentrant smectic C r∗ phases. Another interesting feature of the present investigation was the observation of a field induced transition (FiT) in the LTA+ nBA homologous series. Three threshold field values were noticed which give rise to two new phases (E 1 and E 2) induced by electric field and on further enhancement of the applied field the mesogen behaves like an optical shutter. FiT is reversible in the sense that when applied field is removed the original texture was restored.