WorldWideScience

Sample records for hydraulic hand dynamometer

  1. Test-retest reliability of handgrip strength measurement using a hydraulic hand dynamometer in patients with cervical radiculopathy.

    Science.gov (United States)

    Savva, Christos; Giakas, Giannis; Efstathiou, Michalis; Karagiannis, Christos

    2014-01-01

    The purpose of this study was to evaluate the test-retest reliability of handgrip strength measurement using a hydraulic hand dynamometer in patients with cervical radiculopathy (CR). A convenience sample of 19 participants (14 men and 5 women; mean ± SD age, 50.5 ± 12 years) with CR was measured using a Jamar hydraulic hand dynamometer by the same rater on 2 different testing sessions with an interval of 7 days between sessions. Data collection procedures followed standardized grip strength testing guidelines established by the American Society of Hand Therapists. During the repeated measures, patients were advised to rest their upper limb in the standardized arm position and encouraged to exert 3 maximum gripping efforts. The mean value of the 3 efforts (measured in kilogram force [Kgf]) was used for data analysis. The intraclass correlation coefficient, SEM, and the Bland-Altman plot were used to estimate test-retest reliability and measurement precision. Grip strength measurement in CR demonstrated an intraclass correlation coefficient of 0.976, suggesting excellent test-retest reliability. The small SEM in both testing sessions (SEM1, 2.41 Kgf; SEM2, 2.51 Kgf) as well as the narrow width of the 95% limits of agreements (95% limits of agreement, -4.9 to 4.4 Kgf) in the Bland-Altman plot reflected precise measurements of grip strength in both occasions. Excellent test-retest reliability for grip strength measurement was measured in patients with CR, demonstrating that a hydraulic hand dynamometer could be used as an outcome measure for these patients. Copyright © 2014 National University of Health Sciences. Published by Mosby, Inc. All rights reserved.

  2. Interial sensing in a hand held dynamometer

    NARCIS (Netherlands)

    Veltink, Peter H.; Nieuwland, Daniel M.; Harlaar, Jaap; Baten, Chris T.M.

    1996-01-01

    Two methods for kinematic sensing in a hand-held dynamometer using accelerometers and gyroscopes are presented. The first method integrates the angular velocity signal from the gyroscope, after calibration of gyroscope offset and joint angle from a static period immediately preceding each measuremen

  3. Applicability of hydraulic dynamometer for measuring load mass on forwarders

    Directory of Open Access Journals (Sweden)

    Pandur Zdravko

    2015-01-01

    Full Text Available In the last few years, with the start of wood biomass production from wood residues, the need for determining the quantity of extracted wood residuals on a landing site has appeared. The beginning of intensive usage of wood residues for wood biomass starts in lowland forest where all wood residues are extracted with forwarders. There are several ways to determine load mass on a forwarder, first and probably most accurate is the use of load cells which are installed between forwarder undercarriage and loading space. In Croatia, as far as it is known, there is no forwarder with such equipment, although manufacturers offer the installation of such equipment when buying a new forwarder. The second option is using a portable measuring platform (axle scale which was already used for research of axle loads of trucks and forwarders. The data obtained with the measuring platform are very accurate, while its deficiency is relatively great mass, large dimensions and high price. The third option is determining mass by using hydraulic dynamometer which is installed on crane between the rotator and the telescopic boom. The production and installation of such a system is very simple, and with the price it can easily compete with previously described measuring systems. The main deficiency of this system is its unsatisfying accuracy. The results of assortment mass measuring with hydraulic dynamometer installed on a hydraulic crane and discussion on factors influencing obtained results will be presented in this paper.

  4. Comparison of three hand dynamometers in relation to the accuracy and precision of the measurements

    OpenAIRE

    2012-01-01

    BACKGROUND: Given the variety of available hand-held dynamometers and their different handle shapes, reliability studies are needed. Objectives: To compare the accuracy and reliability between three different hand-held dynamometers and analyze the influence of their handles on grip strength. Methods: The tests were performed with the Jamar® dynamometer, the Takei® dynamometer and the EMG System Manual Transducer with modified handle. Eighteen healthy volunteers aged 20.0±1.3 years without his...

  5. Clinical assessment of hip strength using a hand-held dynamometer is reliable

    DEFF Research Database (Denmark)

    Thorborg, K; Petersen, J; Magnusson, S P;

    2010-01-01

    rotation (ER), internal rotation (IR), flexion (FLEX) and extension (EXT) using a hand-held dynamometer. Nine subjects (five males, four females), physically active for at least 2.5 h a week, were included. Twelve standardized isometric strength tests were performed twice with a 1-week interval in between...

  6. Comparative assessment of knee extensor and flexor muscle strength measured using a hand-held vs. isokinetic dynamometer.

    Science.gov (United States)

    Muff, Guillaume; Dufour, Stéphane; Meyer, Alain; Severac, François; Favret, Fabrice; Geny, Bernard; Lecocq, Jehan; Isner-Horobeti, Marie-Eve

    2016-09-01

    [Purpose] To compare measurements of knee extensor and flexor muscle strength performed using a hand-held dynamometer and an isokinetic dynamometer in apparently healthy subjects. [Subjects and Methods] Thirty adult volunteers underwent knee muscle strength evaluation using an isokinetic or a hand-held dynamometer. [Results] Strong positive correlations were found between the 2 methods, with correlation coefficients r ranging from 0.72 (95% confidence interval [CI], 0.48-0.86) to 0.87 (95% CI, 0.75-0.94), depending on the muscle group and the isokinetic evaluation mode. The reproducibility of the hand-held dynamometer findings was good, judged by a coefficient of variation of 3.2-4.2%. However, the correlation between the 2 methods for the assessment of flexor/extensor ratios ranged from -0.04 to 0.46. [Conclusion] Knee extensor and flexor muscle strength recorded with a hand-held dynamometer is reproducible and significantly correlated with the isokinetic values, indicating that this method may in some cases be a useful replacement for isokinetic strength measurement. However, for strength ratio assessment, and when judged against the isokinetic standard, a hand-held dynamometer is not a valid option.

  7. The Takei Handheld Dynamometer: An Effective Clinical Outcome Measure Tool for Hand and Wrist Function in Boxing.

    Science.gov (United States)

    Gatt, Ian; Smith-Moore, Sophie; Steggles, Charlie; Loosemore, Mike

    2017-05-01

    The aim of this article was to explore retrospectively the Takei dynamometer as a valid and reliable outcome measure tool for hand and wrist pathology in the Great Britain amateur boxing squad between 2010 and 2014. Longitudinal retrospective injury surveillance of the Great Britain boxing squad was performed from 2010 to 2014. The location, region affected, description, and duration of each injury were recorded by the team doctor and team physiotherapists. For each significant injury, we recorded hand grip scores using the Takei handheld dynamometer and compared the scores with baseline measures. At the hand, fractures and dislocations were highly detected with an average difference of 40.2% ( P 20% should be highly considered for significant pathology. The Takei dynamometer is a valid and reliable outcome measure tool for hand and wrist pathologies in boxing. Our study highlights the importance of appropriate clinical tools to guide injury management in this sport.

  8. Reliability and validity of standing balance assessment index using a hand-held dynamometer in stroke patients.

    Science.gov (United States)

    Iwamoto, Koji; Yoshio, Masaharu; Takata, Yuichi; Kozuka, Naoki

    2016-11-01

    [Purpose] This study aimed to determine the reliability and validity of our standing balance assessment index using a hand-held dynamometer (the hand-held dynamometer assessment index) in stroke patients. [Subjects and Methods] The participants were 60 stroke patients with impaired standing balance. Intrarater and interrater reliabilities were evaluated employing the intraclass correlation coefficient. Criterion-related validity was evaluated by Spearman's rank correlation coefficient between the HHD assessment index and the functional balance scale. [Results] The intraclass correlation coefficient values obtained ranged from 0.91 to 0.98, and the correlation coefficient with the FBS was 0.83. [Conclusion] Our findings confirmed the reliability and validity of the hand-held dynamometer assessment index in stroke patients.

  9. A Survey to Determine the Reliability of Dynamometer and Pinch Gauge Dial Readings Among Certified Hand Therapists

    Directory of Open Access Journals (Sweden)

    Theodore I. King II, Ph.D, L.Ac.

    2013-02-01

    Full Text Available Using a cross-sectional descriptive study design, surveys were mailed to 200 randomly selected certified hand therapists of the American Society of Hand Therapists (ASHT to determine how they document analog dynamometer and pinch gauge dial readings. Three different needle settings for the dynamometer and pinch gauge were presented in picture format. For each instrument, one needle setting was just above a gauge marker, one was just below a gauge marker, and one was set exactly between two gauge markers. A total of 126out of 200 surveys were returned for a participation rate of 63%. For the dynamometer readings, therapists estimated the exact strength reading between the two gauge markers 78.3% of the time. For the pinch gauge readings, therapists rounded to the nearest dial marker 76.5% of the time when the needle was just above or just below a dial marker and 61.9% of the time they estimated the reading when the needle was placed exactly between two dial markers.

  10. Medida da força de preensão manual- validade e confiabilidade do dinamômetro saehan Assessment of hand grip strength- validity and reliability of the saehan dynamometer

    Directory of Open Access Journals (Sweden)

    Maurício Moreira Reis

    2011-06-01

    Full Text Available Existe uma grande variedade de instrumentos utilizados para a avaliação da força de preensão manual. Porém, não existem estudos demonstrando a validade e a confiabilidade da maioria destes instrumentos. O objetivo deste estudo foi avaliar a validade concorrente e a confiabilidade intraexaminador do dinamômetro Saehan hidráulico comparado-o com o dinamômetro Jamar hidráulico. Cem indivíduos sadios (50 homens e 50 mulheres, entre 20 e 50 anos de idade, sem alterações cognitivas, deficiências físicas, disfunções neuromusculares e ortopédicas e história de lesões nos membros superiores, foram testados com os dinamômetros Jamar e Saehan. A validade concorrente entre o dinamômetro Jamar e o dinamômetro Saehan foi excelente para os testes de força de preensão realizados com as mãos direita (r=0,976 e esquerda (r=0,986. A confiabilidade intra-examinador foi excelente tanto para o dinamômetro Jamar (r=0,985 mãos direita e esquerda quanto para o dinamômetro Saehan (r=0,981 mão direita e r=0,985 mão esquerda. O dinamômetro Saehan é válido, confiável e comparável com o dinamômetro Jamar. Portanto, dados coletados com o dinamômetro Jamar são equivalentes aos dados coletados com o dinamômetro Saehan. Consequentemente, valores de força obtidos por testes com dinamômetro Saehan podem ser comparados com valores de referência de força de preensão que foram obtidos com o dinamômetro Jamar.There is a great variety of instruments available for evaluating hand grip strength. There is, however, a lack of studies showing the validity and reliability of most of these instruments. The purpose of this study was to examine the concurrent validity and test-retest reliability of the hydraulic Saehan dynamometer using the hydraulic Jamar dynamometer. One hundred healthy subjects (50 men and 50 women, between the ages of 20 and 50 years old, without cognitive impairment, physical disability, neuromuscular or orthopedic dysfunction

  11. Test-retest reliabilities of hand-held dynamometer for lower-limb muscle strength in intellectual disabilities.

    Science.gov (United States)

    Wuang, Yee-Pay; Chang, Jyh-Jong; Wang, Min-Hung; Lin, Hsiu-Ching

    2013-08-01

    The primary purpose of this study was to investigate the test-retest reliabilities of hand-held dynamometer (HDD) for measuring lower-limb muscle strength in intellectual disabilities (ID). The other purposes were to: (1) compare the lower-limb muscle strength between children with and without ID; (2) probe the relationship between the muscle forces and agility performance in ID; and (3) explore the factors associated with muscle strength in ID. Sixty-one participants (30 boys and 31 girls; mean age=14.1 ± 3.3 year) were assessed by the HDD using a "make" test. The comparative group consisted of 63 typically developing children (33 boys and 30 girls; mean age=14.9 ± 2.1 year). The ID group demonstrated lower muscle groups than in typically developing group. Except for the ankle plantarflexors (ICC=0.69, SEM=0.72), test-retest analysis showed good intrarater reliability with ICC ranging from 0.81 to 0.96, and intrarater SEM values ranged from 0.40 to 0.57. The HDD has the potential to be a reliable tool for strength measurement in ID. Muscle strength was positively related to agility performance. Regression analysis indicated that height, weight, BMI, and activity level were significant predictors of muscle strength in ID.

  12. Intra- and inter-rater reliability of isometric shoulder extensor and internal rotator strength measurements performed using a hand-held dynamometer.

    Science.gov (United States)

    Awatani, Takenori; Morikita, Ikuhiro; Shinohara, Junji; Mori, Seigo; Nariai, Miki; Tatsumi, Yasutaka; Nagata, Akinori; Koshiba, Hiroya

    2016-11-01

    [Purpose] The purpose of the present study was to establish the intra- and inter-rater reliability of measurement of extensor strength in the maximum shoulder abducted position and internal rotator strength in the 90° abducted and the 90° external rotated position using a hand-held dynamometer. [Subjects and Methods] Twelve healthy volunteers (12 male; mean ± SD: age 19.0 ± 1.1 years) participated in the study. The examiners were two students who had nonclinical experience with a hand-held dynamometer measurement. The examiners and participants were blinded to measurement results by the recorder. Participants in the prone position were instructed to hold the contraction against the ground reaction force, and peak isometric force was recorded using the hand-held dynamometer on the floor. Reliability was determined using intraclass correlation coefficients. [Results] The intra- and inter-rater reliability data were found to be "almost perfect". [Conclusion] This study investigated intra- and inter-rater reliability and reveald high reliability. Thus, the measurement method used in the present study can evaluate muscle strength by a simple measurement technique.

  13. Reliability of Isometric Knee Extension Muscle Strength Measurements of Healthy Elderly Subjects Made with a Hand-held Dynamometer and a Belt.

    Science.gov (United States)

    Katoh, Munenori; Isozaki, Koji

    2014-12-01

    [Purpose] The purpose of this study was to examine the reliability of three isometric knee extension strength measurements (IKE) made with a hand-held dynamometer (HHD) and a belt of healthy elderly living in the community as subjects. [Subjects] The subject cohort consisted of 186 healthy elderly people, aged 65 to 79 years, living in local communities. [Methods] IKE of the leg subjects used to kick a ball was measured. IKE of each subject was measured three times using an HHD-belt at intervals of 30 seconds. The reliability of the larger of the first two measurements (LV2) as well as the third measurement (3V) was investigated. [Results] The intraclass correlation coefficients [ICC (1, 1)] for LV2 and 3V were 0.955. Bland-Altman analysis showed a fixed bias, and the limits of agreement ranged from -5.6 to 4.6. [Conclusion] The ICC results show that the test-retest reproducibility of IKE measurements of healthy elderly subjects using an HHD-belt is high. However, Bland-Altman analysis showed a fixed bias, suggesting the need for three measurements.

  14. Inter-tester Reliability of the Hand-held dynamometer and the Leg Extensor Power Rig applied on Patients after Total Hip Arthroplasty

    DEFF Research Database (Denmark)

    Mikkelsen, Lone Ramer; Mechlenburg, Inger; Petersen, Annemette Krintel

    INTRODUCTION: Rehabilitation has an increasing focus on intensive resistance training early after joint replacement (1,2). This increases the requests for measuring changes in the muscle strength and muscle power over time. Hand-held dynamometer (HHD) is a device used to measure isometric muscle...... strength and Leg Extensor Power Rig (LEPR) is a tool for measuring muscle power. OBJECTIVES: To test the inter-tester reliability of the HHD in hip abduction and the LEPR in Total Hip Arthroplasty (THA) patients. METHODS: Two groups each consisting 20 subjects were included. Mean age was 68.4 years. All...... the two testers (p=0.62) and the two tests (0.14); ICC=0.91 (95% CI: 0.79;0.96); LOA=±34Watt. CONCLUSION: The relative reliability was acceptable for both HHD and LEPR. The absolute reliability showed that a change in the muscle strength/power above 18 Newton or 34 Watt can be counted as a real change...

  15. Inter-tester Reliability of the Hand-held dynamometer and the Leg Extensor Power Rig applied on Patients after Total Hip Arthroplasty

    DEFF Research Database (Denmark)

    Mikkelsen, Lone Ramer; Petersen, Annemette Krintel; Mikkelsen, Søren Søndergaard

    Background: Rehabilitation has an increasing focus on intensive resistance training early after joint replacement. This increases the requests for measuring changes in the muscle strength and muscle power over time. Hand-held dynamometer (HHD) is a device used to measure isometric muscle strength...... and Leg Extensor Power Rig (LEPR) is a tool for measuring muscle power. Purpose / Aim of Study: To test the inter-tester reliability of the HHD and the LEPR in Total Hip Arthroplasty (THA) patients. Materials and Methods: Two groups each consisting 20 subjects were included. Mean age was 68.4 years. All...... between the two testers (p=0.62) and the two tests (0.14); ICC=0.91 (95% CI: 0.79;0.96); LOA=±34Watt. Conclusions: The relative reliability was acceptable for both HHD and LEPR. The absolute reliability showed that a change in the muscle strength/power above 18 Newton or 34 Watt can be counted as a real...

  16. Hydraulics.

    Science.gov (United States)

    Decker, Robert L.; Kirby, Klane

    This curriculum guide contains a course in hydraulics to train entry-level workers for automotive mechanics and other fields that utilize hydraulics. The module contains 14 instructional units that cover the following topics: (1) introduction to hydraulics; (2) fundamentals of hydraulics; (3) reservoirs; (4) lines, fittings, and couplers; (5)…

  17. Hip- and knee-strength assessments using a hand-held dynamometer with external belt-fixation are inter-tester reliable

    DEFF Research Database (Denmark)

    Thorborg, Kristian; Bandholm, Thomas; Hölmich, Per

    2013-01-01

    PURPOSE: In football, ice-hockey, and track and field, injuries have been predicted, and hip- and knee-strength deficits quantified using hand-held dynamometry (HHD). However, systematic bias exists when testers of different sex and strength perform the measurements. Belt-fixation of the dynamome......PURPOSE: In football, ice-hockey, and track and field, injuries have been predicted, and hip- and knee-strength deficits quantified using hand-held dynamometry (HHD). However, systematic bias exists when testers of different sex and strength perform the measurements. Belt...

  18. Avaliação da fatigabilidade em pacientes com esclerose múltipla através do dinamômetro manual Fatigability evaluation on multiple sclerosis patients by using a hand held dynamometer

    Directory of Open Access Journals (Sweden)

    Karina Pavan

    2006-06-01

    Full Text Available A fadiga é um dos mais freqüentes sintomas e incapacitantes na esclerose múltipla (EM. O objetivo do presente estudo foi avaliar a fatigabilidade em pacientes com EM pela aplicação de exercícios isotônicos e isométricos com dinamômetro manual. Como resultados, a fatigabilidade, a força e o tempo máximo de isometria são semelhantes estatisticamente entre o grupo controle e o grupo de EM. Conclui-se que embora a queixa subjetiva de fadiga seja freqüente na EM, a fatigabilidade e a recuperação após o exercício demonstraram ser normais.Fatigue is one of the most commom disabling symptoms in multiple sclerosis (MS. The aim of this study was to evaluate the fatigability on patients with MS by the aplication of hand grip isotonic and isometric exercises with dynamometer. As results the fatigability, the isometric strenght and time were statistically similar in the control group and in MS. We conclude that although fatigue is a frequent subjective complaint on MS, the fatigability and the recover after exercises seems to be normal.

  19. Comparison of three hand dynamometers in relation to the accuracy and precision of the measurements Comparação de três dinamômetros de preensão manual relacionados à exatidão e precisão das medidas

    Directory of Open Access Journals (Sweden)

    Josária F. Amaral

    2012-06-01

    Full Text Available BACKGROUND: Given the variety of available hand-held dynamometers and their different handle shapes, reliability studies are needed. Objectives: To compare the accuracy and reliability between three different hand-held dynamometers and analyze the influence of their handles on grip strength. Methods: The tests were performed with the Jamar® dynamometer, the Takei® dynamometer and the EMG System Manual Transducer with modified handle. Eighteen healthy volunteers aged 20.0±1.3 years without history of musculoskeletal disorders or trauma in the evaluated limbs were included. Data normality was tested using the Shapiro-Wilk test. To verify possible differences between the dynamometers, repeated measures ANOVA was administered, followed by Tukey post-hoc tests. Reliability between measurements was evaluated using intraclass correlation coefficient (ICC and agreement was tested using Bland and Altman plots. The dynamometers calibration process was evaluated using linear regressions. RESULTS: We observed statistically significant differences on the female group between the Jamar® and the Takei® dynamometers (females pCONTEXTUALIZAÇÃO: Dada a variedade de dinamômetros disponíveis para mensurar a força de preensão manual com diferentes formatos de empunhaduras, estudos de confiabilidade fazem-se necessários. Objetivos: Comparar a exatidão e a precisão das medidas de três dinamômetros distintos e analisar a influência do perfil de empunhadura de cada um. MÉTODOS: Os testes foram realizados com os dinamômetros Jamar®, Takei® e o Transdutor Manual EMG System com empunhadura modificada. Foram avaliados 18 voluntários saudáveis, com idade de 20±1,3 anos, sem histórico de doença musculoesquelética ou traumas nos membros avaliados. A normalidade dos dados foi testada por meio do teste Shapiro-Wilk. Para verificar as possíveis diferenças entre as medições dos dinamômetros, aplicou-se uma ANOVA para medidas repetidas seguida do

  20. Wireless Crankarm Dynamometer for Cycling

    Directory of Open Access Journals (Sweden)

    Caetano Decian LAZZARI

    2011-05-01

    Full Text Available This report describes a new crankarm dynamometer designed to evaluate the strength produced by cyclists in real conditions. The dynamometer was designed to be fitted on a conventional crankset while data were transmitted via wireless communication channels available on a BluetoothTM module. Some 3D solid models were created in the SolidsWorks2010TM development environment to analyze the static and dynamic characteristics, by using the finite elements technique. Each crankset arm was used as a load cell based on strain gages configured as two Wheatstone bridges. The signals were conditioned on a printed circuit board attached directly to the structure. As a result, the load cell shows a maximum nonlinearity error between 2.1 % and 2.8 %. Some tests were performed on a cycling trainer, allowing to evaluate the system's functionality and to determine the involved forces in the crankset.

  1. AC dynamometer; Koryu dinamo meter

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-01-10

    Fuji Electric Co., Ltd., developed an AC dynamometer for testing automobiles, and the product was delivered to Hokkaido Automotive Engineering College via Safety Automobile Company. The device is used for testing 1,300cc-class automobiles. It is similar to the conventional type in that its force of reaction to an imposed load is measured by load cells. It is a variable speed motor driven by an inverter (FRENIC5000VG5), whose specifications and features are mentioned below. It is a totally-enclosed self-cooled oscillating AC dynamometer that outputs 75kW, revolves at 1500/2868rpm, and operates for 30min. Since it is rated for a short time operation, the external fan is dispensed with, and this reduces noise. A number of parts for the standard type (R90 series) are utilized for reduction in the cost, and the time required for its delivery was short. (NEDO)

  2. Calibration Procedure for 3D Turning Dynamometer

    DEFF Research Database (Denmark)

    Axinte, Dragos Aurelian; Belluci, Walter

    1999-01-01

    The aim of the static calibration of the dynamometer is to obtain the matrix for evaluating cutting forces through the output voltage of the piezoelectric cells and charge amplifiers. In the same time, it is worth to evaluate the linearity of the dependencies between applied forces and output...... of the piezoelectric cells;5. Mounting of the dynamometer;6. Calibration of the dynamometer;7. Data analysis;8. Uncertainty budget of the calibration....

  3. Calibration Procedure for 3D Turning Dynamometer

    DEFF Research Database (Denmark)

    Axinte, Dragos Aurelian; Belluci, Walter

    1999-01-01

    The aim of the static calibration of the dynamometer is to obtain the matrix for evaluating cutting forces through the output voltage of the piezoelectric cells and charge amplifiers. In the same time, it is worth to evaluate the linearity of the dependencies between applied forces and output...... of the piezoelectric cells;5. Mounting of the dynamometer;6. Calibration of the dynamometer;7. Data analysis;8. Uncertainty budget of the calibration....

  4. Comparison of Jamar and Bodygrip Dynamometers for Handgrip Strength Measurement.

    Science.gov (United States)

    Guerra, Rita S; Amaral, Teresa F; Sousa, Ana S; Fonseca, Isabel; Pichel, Fernando; Restivo, Maria T

    2017-07-01

    Guerra, RS, Amaral, TF, Sousa, AS, Fonseca, I, Pichel, F, and Restivo, MT. Comparison of Jamar and Bodygrip dynamometers for handgrip strength measurement. J Strength Cond Res 31(7): 1931-1940, 2017-Studies that compared the agreement between Jamar and other models of dynamometers for handgrip strength (HGS) measurement have exhibited variability in the provided results. The lack of comparability between dynamometers led to the development of the Bodygrip dynamometer. This study aims to examine the reliability of the Bodygrip for HGS measurement, to compare it with the Jamar, and to explore the HGS differences between instruments considering the ergonomic effect of using the Bodygrip with 2 different handles. A cross-sectional study was conducted in free-living (n = 114, 18-89 years) and inpatient (n = 50, 65-93 years) volunteers. Nondominant HGS was tested randomly with the Jamar and Bodygrip, the latter using 2 different handles-curved and straight types. Handgrip strength was obtained for each participant under the same conditions. Each individual performed 2 HGS measurements with each dynamometer, and the maximum HGS value was considered for dynamometers comparison. Differences in the maximum HGS value between the 2 devices (Jamar-Bodygrip), intraclass correlation coefficients (ICCs), Bland and Altman plots, and limits of agreement were obtained. Correlation between the highest HGS measurement obtained for the nondominant hand with the Jamar and with the Bodygrip using each handle was excellent (ICCs: 0.93-0.95). Mean differences of -0.5 (limits of agreement: -4.6; 3.5) kgf with the curved handle and of 1.0 (-7.7; 9.7) kgf with the straight handle for the free-living participants were obtained, whereas for inpatients these values were -1.0 (-3.8; 1.9) kgf and 2.1 (-3.3; 7.5) kgf, respectively, for the curved and straight handles. The Bodygrip is comparable to the Jamar in free-living adults and in hospitalized older adults, exhibiting excellent interinstrument

  5. Finite Element Analysis of Inertia Dynamometer

    Directory of Open Access Journals (Sweden)

    R. A. Gujar

    2013-12-01

    Full Text Available The Dynamometer is a LOAD device. It applies a load to an engine so we can test the performance of the engine under a variety of circumstances. System operates where load (dyno torque equals that of the Engine. By varying the engine throttle and load we can test any point under the engines max torque curve. We design and modify engines for improved fuel economy and emissions We need DATA to quantify the improvements in Fuel savings and Emissions reductions. This data will be used to help us “tune in” our design. The Dynamometer is operated at 1000 rpm to generate the necessary inertia. For different kind of conditions, there is need of having variable inertia. So the dynamometer is constructed with removable flywheel.

  6. Long-term outcome of muscle strength in ulnar and median nerve injury: Comparing manual muscle strength testing, grip and pinch strength dynamometers and a new intrinsic muscle strength dynamometer

    NARCIS (Netherlands)

    A.R. Schreuders (Ton); M.E. Roebroeck (Marij); J.B. Jaquet (Jean); S.E.R. Hovius (Steven); H.J. Stam (Henk)

    2004-01-01

    textabstractObjective: To compare the outcome of muscle strength with manual muscle strength testing grip and pinch strength measurements and a dynamometer which allows for measurements of the intrinsic muscles of the hand in isolation (the Rotterdam Intrinsic Hand Myometer, RIHM). Methods:

  7. Long-term outcome of muscle strength in ulnar and median nerve injury: Comparing manual muscle strength testing, grip and pinch strength dynamometers and a new intrinsic muscle strength dynamometer

    NARCIS (Netherlands)

    A.R. Schreuders (Ton); M.E. Roebroeck (Marij); J.B. Jaquet (Jean); S.E.R. Hovius (Steven); H.J. Stam (Henk)

    2004-01-01

    textabstractObjective: To compare the outcome of muscle strength with manual muscle strength testing grip and pinch strength measurements and a dynamometer which allows for measurements of the intrinsic muscles of the hand in isolation (the Rotterdam Intrinsic Hand Myometer, RIHM). Methods: Thirty-f

  8. 40 CFR 86.208-94 - Dynamometer.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Dynamometer. 86.208-94 Section 86.208-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... Later Model Year Gasoline-Fueled New Light-Duty Vehicles, New Light-Duty Trucks and New...

  9. 40 CFR 90.409 - Engine dynamometer test run.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine dynamometer test run. 90.409... Test Procedures § 90.409 Engine dynamometer test run. (a) Engine and dynamometer start-up. (1) Only... practice. (3) For Phase 1 engines, at the manufacturer's option, the engine can be run with the throttle...

  10. 21 CFR 888.1240 - AC-powered dynamometer.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false AC-powered dynamometer. 888.1240 Section 888.1240...) MEDICAL DEVICES ORTHOPEDIC DEVICES Diagnostic Devices § 888.1240 AC-powered dynamometer. (a) Identification. An AC-powered dynamometer is an AC-powered device intended for medical purposes to...

  11. Hand-held Dynamo-metry

    OpenAIRE

    Ploeg, Rutger Jan Otto van der

    1992-01-01

    This study describes the application of a hand-held dynamometer that was designed to measure muscle strength in normal individuals and neurological patients in a simple way, comparable to manual muscle testing. Zie: Summary

  12. Information Processing of Chassis Dynamometer based on Controller Area Network

    Directory of Open Access Journals (Sweden)

    Shupeng Zhao

    2013-06-01

    Full Text Available The development of chassis dynamometer of hybrid vehicle based on CAN bus was studied. Chassis dynamometer of hybrid vehicle measurement methods and loading devices are analyzed, and laid the foundation for the resistance simulation of chassis dynamometer. Road resistance simulation on HEV chassis dynamometer is researched, getting electric quantity simulation type of chassis dynamometer driving resistance. The research and development of hybrid vehicle chassis dynamometer based on CAN Bus is conducive to enhance the level of whole hybrid vehicle and car assembly, establish the test procedures, test methods and test standards, provide a research platform and methods for test evaluation of HEV energy utilization. The chassis dynamometer system needs to be calibrated in order to ensure its accuracy .The drum Test bench surface traction can be measured from the motor casing tangential force using force sensor mounted on the motor casing. The design adopts bidirectional calibration arm, it can decrease the effect of extra torque to ensure the test precision of automobile chassis dynamometer surface traction. The method of hybrid vehicles fuel consumption experiment test is analyzed through experiment test on the HEV chassis dynamometer and actual road. We obtain some regularity of hybrid vehicles energy consumption and hybrid vehicles fuel consumption test method through studying lightweight hybrid vehicles fuel economy.

  13. Long-term outcome of muscle strength in ulnar and median nerve injury: Comparing manual muscle strength testing, grip and pinch strength dynamometers and a new intrinsic muscle strength dynamometer

    OpenAIRE

    Schreuders, Ton; Roebroeck, Marij; Jaquet, Jean; Hovius, Steven; Stam, Henk

    2004-01-01

    textabstractObjective: To compare the outcome of muscle strength with manual muscle strength testing grip and pinch strength measurements and a dynamometer which allows for measurements of the intrinsic muscles of the hand in isolation (the Rotterdam Intrinsic Hand Myometer, RIHM). Methods: Thirty-four patients more than 2 years after ulnar and/or median nerve injury. Muscle strength was evaluated using manual muscle strength testing (MMST), grip, pinch and intrinsic muscle strength measureme...

  14. Hand Grip Strength Vs. Sprint Effectiveness in Amputee Soccer Players

    Directory of Open Access Journals (Sweden)

    Wieczorek Marta

    2015-12-01

    Full Text Available Amputee soccer is one of the types of soccer designed for the disabled, especially those who have undergone amputations, as well as those with extremity dysfunction. The objective of the study was to find the relationship between hand grip strength and sprint time in amputee soccer players. Thirteen field amputee soccer players participated in the study. A SAEHAN hydraulic hand dynamometer manufactured by Jamar was used for hand grip strength measurements. The sprint running test was conducted over a distance of 30 m. The Fusion Smart Speed System was employed for running time measurements. No statistically significant relationships were found between hand grip strength of the left or right hand, and sprint times over 1, 5, 10, 15, 20, 25 and 30 m. Analysis of the running velocity curve of the subjects showed an interesting profile characterized by a 15 meter-long acceleration phase and a significant velocity increase over a distance of 20 – 25 m. The study suggests that there is no relationship between hand grip strength and sprint effectiveness in amputee soccer players. The specificity of locomotion with the use of elbow crutches among elite Polish amputee soccer players probably accounts for the profile of the sprint velocity curve. Extension of the acceleration phase in the sprint run and a velocity increase in the subsequent part of the run were observed.

  15. Evaluating Hand Function in Clients with Trigger Finger

    Directory of Open Access Journals (Sweden)

    Danit Langer

    2017-01-01

    Full Text Available Background. Trigger finger (TF is a common hand pathology frequently encountered in hand clinics. Occupational therapists predominantly assess TF symptoms as opposed to using standardized hand functioning assessments. The purpose of this study was to assess the construct validity of dexterity and grip strength assessments for clients with TF. Method. Sixty-three participants with TF and 66 healthy controls were administered the Functional Dexterity Test (FDT, Purdue Pegboard Test (PPT, and Jamar® Hydraulic Hand Dynamometer (JD and completed the Disabilities of Arm Shoulder and Hand questionnaire (DASH. TF symptoms were graded using the Quinnell classification. Results. Statistically significant differences were found between the groups in dexterity and grip strength. A statistically significant difference between the three TF grades was found on the PPT. All three test scores were moderately correlated with the DASH scores. Conclusion. This study provides innovative evidence for the validity of common hand function assessments for individuals with TF and recommends incorporating these tools in clinical practice. Further research is needed with larger samples and better representation of each TF clinical grade.

  16. The Impacts of Hydraulic Fracturing in the Eagle Ford Shale Region, South Texas: Hands-On Activities for Middle and High School Students

    Science.gov (United States)

    Kohlmeyer, C.; Loisel, J.; Schade, G. W.

    2016-12-01

    The Eagle Ford Shale (EFS) region of south-central Texas is strongly affected by a rapid increase in unconventional oil and gas production, and it ranks amongst the top production regions of the country. Across the EFS region and elsewhere, the fracking boom has been causing large emissions of methane (CH4) and non-methane hydrocarbons to the atmosphere, with direct consequences on atmospheric GHG concentration and air quality. An increase in seismic activity has also been reported in the area. Since these effects were initially underestimated, fracking operations remain largely unmitigated by regulation. As a result, large-scale oil and gas operations are found in close geographical proximity to rural communities who are uninformed and/or not accustomed to such operations and their effects on the environment and human health. Here we present a few hands-on activities that are being developed to educate middle and high school students on hydraulic fracturing and associated land-use change, water and air pollution, and seismicity induced by deep well injection. Modules on the carbon cycle (with an emphasis on CO2 and CH4), global environmental change, and human energy consumption around the world and main energy sources are also under development. Each activity is either based on scientific data gathered by students or information that is freely available; mapping exercises and time series analysis are included. For example, students will implement a geographic information system (GIS) to study local land-use change using satellite imagery analysis. These activities will be implemented in Fall 2016 and Spring 2017 in at least one Independent School District of the Eagle Ford Shale area. A broadly applicable educational booklet/teaching module on atmospheric CH4 emissions, with an emphasis on the environmental impacts of the oil and gas industry as the dominant source of emissions and land use change in shale areas, will be published.

  17. 40 CFR 86.1337-2007 - Engine dynamometer test run.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Engine dynamometer test run. 86.1337... Procedures § 86.1337-2007 Engine dynamometer test run. (a) The following steps shall be taken for each test...) Immediately after the engine is turned off, turn off the engine cooling fan(s) if used. As soon as...

  18. 40 CFR 86.1337-96 - Engine dynamometer test run.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Engine dynamometer test run. 86.1337... Procedures § 86.1337-96 Engine dynamometer test run. (a) The following steps shall be taken for each test: (1... system from the CVS). As soon as possible, transfer the “cold start cycle” exhaust and dilution air...

  19. 40 CFR 86.1237-85 - Dynamometer runs.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Dynamometer runs. 86.1237-85 Section... Methanol-Fueled Heavy-Duty Vehicles § 86.1237-85 Dynamometer runs. (a) The vehicle shall be either driven... the diurnal loss test and beginning of the hot soak preparation run shall not exceed 3 minutes,...

  20. 40 CFR 86.1237-96 - Dynamometer runs.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Dynamometer runs. 86.1237-96 Section 86.1237-96 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... Methanol-Fueled Heavy-Duty Vehicles § 86.1237-96 Dynamometer runs. Section 86.1237-96 includes text...

  1. 油压机械臂及手系统递归神经网络建模与位置控制%Recurrent Neural Networks Modeling and Position Control of Hydraulic Manipulator and Hand

    Institute of Scientific and Technical Information of China (English)

    邵辉; 野波健藏

    2012-01-01

    The model and inverse model of angular velocity of a hydraulic manipulator and a hydraulic robotic hand are established using recurrent neural networks, providing an effective so- lution to the modeling and control of dynamic hydraulic systems. The inverse models are used as position controllers of the manipulator and the hand. Experiments show that the models are close enough to the system dynamics with accuracy of position control satisfying the requirements.%为解决多关节油压机械臂及手系统动态参数的时变性,应用递归神经网络(RNN)建立了油压机械臂及手的速度模型及逆模型,并用逆模型作为臂及手各关节的控制器实现了位置控制。实验结果表明,所建模型性能接近系统性能,位置控制精度也能达到控制目标的要求。

  2. 手持式电子肌力测定仪在痉挛型脑瘫儿童下肢肌力测定中的信度研究%The reliability of hand-held electronic dynamometer tests for lower limb muscle strength measurement in children with spastic cerebral palsy

    Institute of Scientific and Technical Information of China (English)

    史惟; 朱默; 骆丹丹; 杨红; 陈冬冬; 黄华玉

    2010-01-01

    Objective To determine the reliability of hand-held electronic dynamometer (HHD) tests for lower limb muscle strength measurement in children with spastic cerebral palsy (CP). Methods Twenty-eight children ( 15 boys and 13 girls; mean age 5 years 8 months) with different types of CP (2 with spastic quadriplegia,8 spastic diplegia, 6 hemiplegia, 1 triplegia and 1 monoplegia) , and at different functional levels ( 19 graded at gross motor function classification system level Ⅰ, 6 level Ⅱ, 2 level Ⅲ and 1 level Ⅳ ) were recruited from the Rehabilitation Center of the Children's Hospital of Fudan University. Standardized HHD protocols were used to measure the strength of their hip, knee and ankle muscles. The HHD test was performed by the same examiner twice with an interval of 10 min in between. The HDD test was also performed with 15 randomly selected CP children by 2 examiners with an interval of 10 min in between. The test-retest and inter-rater reliabilities of the HDD readings were determined by calculating the intra- and inter-class correlation coefficients. Results The HHD measurements showed fine testretest reliability ( ICC = 0.74-0.97 ) and inter-rater reliability ( ICC = 0.63-0.97 ) in measuring lower-limb muscle strength of children with spastic CP, with the highest test-retest reliability for the hip flexion, foot plantar flexion and knee extension muscle groups. The highest inter-rater reliability was achieved with the hip flexion and foot dorsiflexion muscle groups. Conclusions Standardized HHD testing of lower-limb muscle strength in children with spastic CP shows fine test-retest and inter-rater reliability. The HHD can reliably assess the lower-limb muscle strength of children with spastic CP.%目的 探讨手持式电子肌力测定仪在痉挛型脑瘫儿童下肢肌力测定中的信度.方法 以2009年2月至11月在复旦大学附属儿科医院康复中心接受康复治疗的28例3岁以上的痉挛型脑瘫患儿为研究对象,采

  3. NASA project 1: Full-body dynamometer

    Science.gov (United States)

    Lu, Li-Dai

    1993-01-01

    In space, where the body does only a fraction of work it does on earth, muscle atrophy is a major concern. The bones and the muscles will begin to deteriorate after a short stay in weightlessness. Bone decalcification appears to be a major problem with extensive living in microgravity. Resistance exercise is not only essential to prevent muscle atrophy in space, it also helps to keep bone decalcification in check. For a space station, where the astronauts are expected to live for months at a time, exercise is especially important. Experts recommend about an hour and a half to two hours of exercise per day to keep the muscles in good condition in microgravity. The exercises will not only keep the astronauts in excellent physical condition, it will also make it easier for them to readjust to earth's gravity on return. The stationary bicycle and the treadmill have been the astronauts' primary sources of exercise since the 1970's. The major problem with both the stationary bicycle and the treadmill is that while they may keep the leg muscles from deteriorating in microgravity, they do little for muscles in the upper body. The National Aeronautics and Space Administration (NASA) is currently developing a full-body dynamometer (FBD), which will provide the astronauts with a full-body workout. It will also test the astronauts for muscle atrophy and rehabilitate the weakened muscle. The specification and the function structure for the FBD is presented.

  4. Design, fabrication, and evaluation of a wireless pull-type dynamometer

    Directory of Open Access Journals (Sweden)

    I Ahmadi

    2016-09-01

    Full Text Available Introduction Measurement of the draft force exerted from agricultural machineries to the tractor and the calculation of the implement power requirements is important for agriculturalists in terms of machine design and tractor-machine matching . Therefore, studies about this issue have been started from the 1950’s. Zoerbet al.,(1983 claimed that the first dynamometers have been made of spring and in reality, users had difficulties reading these dynamometers gauge due to the quick variations of the gauge pointer. Therefore the second stage was the development of the hydraulic-type dynamometers in which the oil pressure inside the hydraulic cylinder-piston set installed between machine and tractor that can be readable with a bourdontube gauge was considered as its indicator. From the first years of the 1960’s development of the strain-gauge pull-type dynamometers started. In this study, design, fabrication and evaluation of a pull-type tractor dynamometer is considered that can be used to measure and store tractor forward velocity, and horizontal component of draft force exerted from wheel-type towed implements to the tractor. Therefore, drawbar power needed to pull the machine through the soil can be calculated. This dynamometer can also be utilized to measure three-point-hitch implement’s draft force and power requirements in condition that the RNAM (1983 method was used. In addition to measure the tractor velocity with a GPS receiver instead of a fifth wheel, the other particular issue about this dynamometer is that a remote controller is used to order data acquisition commands such as starting, ending, pausing and time zeroing in the process of data gathering. Materials and Methods In this study an S-type strain gauge load cell (model: SS300 and a GPS receiver (model: Micro GPS antenna AGM-10 + NEO-6-M-0-001 ublox AG board were utilized to measure the draft force and forward velocity, respectively. To calibrate the load cell sensor, in an

  5. Accuracy of exhaust emission factor measurements on chassis dynamometer

    NARCIS (Netherlands)

    Joumard, R.; Laurikko, J.; Han, T.L.; Geivanidis, S.; Samaras, Z.; Merétei, T.; Devaux, P.; André, J.-M.; Cornelis, E.; Lacour, S.; Prati, M.V.; Vermeulen, R.; Zallinger, M.

    2009-01-01

    The influence of 20 parameters on the measurement of light-vehicle emission factors on chassis dynamometer based on driving patterns, vehicle-related parameters, vehicle sampling, and laboratory-related parameters, was studied. The results were based on literature synthesis, ≈ 2700 specific tests

  6. 40 CFR 86.537-90 - Dynamometer test runs.

    Science.gov (United States)

    2010-07-01

    .../s). (iii) For methanol samples, the flow rates shall be set such that the system meets the design... rates shall be set such that the system meets the design criteria of § 86.509. For impinger samples in.... (11) Operate the vehicle according to the Urban Dynamometer Driving Schedule (§ 86.515). (12) At the...

  7. 40 CFR 86.884-8 - Dynamometer and engine equipment.

    Science.gov (United States)

    2010-07-01

    ... described in § 86.884-7. (b) An engine cooling system having sufficient capacity to maintain the engine at... manufacturer in his sales and service literature, for the engine being tested. ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Dynamometer and engine equipment....

  8. Hydraulic structures

    CERN Document Server

    Chen, Sheng-Hong

    2015-01-01

    This book discusses in detail the planning, design, construction and management of hydraulic structures, covering dams, spillways, tunnels, cut slopes, sluices, water intake and measuring works, ship locks and lifts, as well as fish ways. Particular attention is paid to considerations concerning the environment, hydrology, geology and materials etc. in the planning and design of hydraulic projects. It also considers the type selection, profile configuration, stress/stability calibration and engineering countermeasures, flood releasing arrangements and scouring protection, operation and maintenance etc. for a variety of specific hydraulic structures. The book is primarily intended for engineers, undergraduate and graduate students in the field of civil and hydraulic engineering who are faced with the challenges of extending our understanding of hydraulic structures ranging from traditional to groundbreaking, as well as designing, constructing and managing safe, durable hydraulic structures that are economical ...

  9. HAND-HELD MYOMETRY - REFERENCE VALUES

    NARCIS (Netherlands)

    VANDERPLOEG, RJO; FIDLER, [No Value; OOSTERHUIS, HJGH

    1991-01-01

    In thirteen major muscle groups of 50 healthy females and 50 males, aged 20-60 years, maximum voluntary contraction was measured with a hand-held dynamometer. The intrasession variation, the left-right variation, and the fifth and fiftieth centile values were calculated. The ratio of two observation

  10. HYDRAULIC SERVO

    Science.gov (United States)

    Wiegand, D.E.

    1962-05-01

    A hydraulic servo is designed in which a small pressure difference produced at two orifices by an electrically operated flapper arm in a constantly flowing hydraulic loop is hydraulically amplified by two constant flow pumps, two additional orifices, and three unconnected ball pistons. Two of the pistons are of one size and operate against the additional orifices, and the third piston is of a different size and operates between and against the first two pistons. (AEC)

  11. NREL-Prime Next-Generation Drivetrain Dynamometer Test Report

    Energy Technology Data Exchange (ETDEWEB)

    Keller, Jonathan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Erdman, Bill [Cinch, Inc., Moraga, CA (United States); Blodgett, Douglas [DNV KEMA Renewables, Burlington, VT (United States); Halse, Christopher [Romax Technology, Boulder, CO (United States)

    2016-08-01

    Advances in wind turbine drivetrain technologies are necessary to improve reliability and reduce the cost of energy for land-based and offshore wind turbines. The NREL-Prime Next-Generation Drivetrain team developed a geared, medium-speed drivetrain that is lighter, more reliable and more efficient than existing designs. One of the objectives of Phase II of the project was to complete the detailed design, fabrication, and dynamometer testing of a 750 kilowatt (kW) drivetrain that includes the key gearbox innovations designed by Romax Technology and power converter innovations designed by DNV Kema Renewables. The purpose of this document is to summarize these tests completed in NREL's National Wind Technology Center 2.5 megawatt (MW) dynamometer.

  12. Digital Dynamometer and Goniometer in Analyzing Isometric Capacities and Tennis Serving

    Directory of Open Access Journals (Sweden)

    Liu Chia-Che

    2016-01-01

    Full Text Available The study was to investigate relation between tennis serving techniques and shoulder joint muscles in various skilled players in Taiwan. The study used Micro FET3 (Digital Manual Muscle Dynamometer and Goniometer which appraised the isometric capacity of the shoulder joint and perimeter muscle. The research consists of 13 collegiate male tennis players; 6 players were in elite groups and the other 7 players were in general groups. The tennis players performed 30 servers testing the range to appraise serve technique reflect. The application of t-test and Linear Regression analyzed the serve technique reflect interrelated with the shoulder joint muscle. The muscle strength and the serve accuracy predominate interrelated place where middle trapezius, shoulder internal rotator, and shoulder external rotator of favor hands were obvious. The muscle strength and the serve speed predominated interrelated place where shoulder internal rotator and shoulder external rotator of favor hands were obvious. This study also discovered triceps of favor hands, shoulder extensor, shoulder abductor, triceps, and middle trapezius of non- favor hands muscle strength didn't have any outstanding reference with tennis league table. The research confirmed that the shoulder joint muscle discipline increased shoulder internal rotator, shoulder external rotator, and middle trapezius that help the serve technique reflect.

  13. Basic hydraulics

    CERN Document Server

    Smith, P D

    1982-01-01

    BASIC Hydraulics aims to help students both to become proficient in the BASIC programming language by actually using the language in an important field of engineering and to use computing as a means of mastering the subject of hydraulics. The book begins with a summary of the technique of computing in BASIC together with comments and listing of the main commands and statements. Subsequent chapters introduce the fundamental concepts and appropriate governing equations. Topics covered include principles of fluid mechanics; flow in pipes, pipe networks and open channels; hydraulic machinery;

  14. Hydraulic Structures

    Data.gov (United States)

    Department of Homeland Security — This table is required whenever hydraulic structures are shown in the flood profile. It is also required if levees are shown on the FIRM, channels containing the...

  15. Electric vehicle chassis dynamometer test methods at JPL and their correlation to track tests

    Science.gov (United States)

    Marte, J.; Bryant, J.

    1983-01-01

    Early in its electric vehicle (EV) test program, JPL recognized that EV test procedures were too vague and too loosely defined to permit much meaningful data to be obtained from the testing. Therefore, JPL adopted more stringent test procedures and chose the chassis dynamometer rather than the track as its principal test technique. Through the years, test procedures continued to evolve towards a methodology based on chassis dynamometers which would exhibit good correlation with track testing. Based on comparative dynamometer and track test results on the ETV-1 vehicle, the test methods discussed in this report demonstrate a means by which excellent track-to-dynamometer correlation can be obtained.

  16. Hand to hand.

    Science.gov (United States)

    Bedell, Susanna E; Graboys, Thomas B

    2002-08-01

    Examination of the hands has the potential to transform the encounter between physician and patient. Taking the hands conveys a sense of warmth and connectedness and is a means to communicate the physician's mindfulness. The hands can focus the examination on the individual patient as a complete human being, and not merely a disease or a collection of symptoms. The hands provide readily accessible information that may not be available through other evaluations, and they offer clues to a patient's physical and mental health. Commonplace observations, such as those revealed in the hands, can unravel medical mysteries and provide profound clinical insights.

  17. 40 CFR 86.340-79 - Gasoline-fueled engine dynamometer test run.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Gasoline-fueled engine dynamometer... Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test Procedures § 86.340-79 Gasoline-fueled engine dynamometer test run. (a) This section applies to...

  18. 40 CFR 86.237-94 - Dynamometer test run, gaseous emissions.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Dynamometer test run, gaseous... test run, gaseous emissions. (a) The complete dynamometer test consists of a cold start drive of... terminates after the first period (505 seconds) is run. (d) The provisions of § 86.137(b) apply to...

  19. 40 CFR 86.137-96 - Dynamometer test run, gaseous and particulate emissions.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Dynamometer test run, gaseous and particulate emissions. 86.137-96 Section 86.137-96 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... New Otto-Cycle Complete Heavy-Duty Vehicles; Test Procedures § 86.137-96 Dynamometer test run,...

  20. 40 CFR 86.137-90 - Dynamometer test run, gaseous and particulate emissions.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Dynamometer test run, gaseous and... New Otto-Cycle Complete Heavy-Duty Vehicles; Test Procedures § 86.137-90 Dynamometer test run, gaseous... first period (505 seconds) is run. (2) Petroleum-fueled and methanol-fueled diesel vehicles. The...

  1. 40 CFR 86.341-79 - Diesel engine dynamometer test run.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Diesel engine dynamometer test run. 86.341-79 Section 86.341-79 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR....341-79 Diesel engine dynamometer test run. (a) This section applies to Diesel engines only....

  2. Further advancement of chassis-dynamometer measurement and control technology; Kodoka suru chassis dinamo keisoku seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Y. [Meidensha Corp., Tokyo (Japan)

    1999-03-01

    A new chassis-dynamometer was developed and put into the practical use in 1992. Currently this chassis-dynamometer, in which rollers are mounted on the AC-dynamometer shaft end, is being used in the majority of passenger car testing application. This paper present bow the associated measurement and control technology was upgraded and discusses the future trend in this field. (author)

  3. Fatigability evaluation on multiple sclerosis patients by using a hand held dynamometer

    OpenAIRE

    Karina Pavan; Kizi Schmidt; Tatiana de Ambrosio Ariça; Maria Fernanda Mendes; Charles Peter Tilbery; Sergio Lianza

    2006-01-01

    A fadiga é um dos mais freqüentes sintomas e incapacitantes na esclerose múltipla (EM). O objetivo do presente estudo foi avaliar a fatigabilidade em pacientes com EM pela aplicação de exercícios isotônicos e isométricos com dinamômetro manual. Como resultados, a fatigabilidade, a força e o tempo máximo de isometria são semelhantes estatisticamente entre o grupo controle e o grupo de EM. Conclui-se que embora a queixa subjetiva de fadiga seja freqüente na EM, a fatigabilidade e a recuperação ...

  4. 40 CFR 86.1327-96 - Engine dynamometer test procedures; overview.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES... dynamometer. Rust inhibitors and lubrication additives may be used, up to the levels recommended by...

  5. MDS-Multifunctional Dynamometer for Application in Space

    Science.gov (United States)

    Adamcik, G.; Barta, N.; Talla, R.; Angeli, T.; Kozlovskaya, I. B.; Grigoriev, A. I.; Tschan, H.; Bachl, N.

    2008-06-01

    The project MDS (Multifunctional Dynamometer for Application in Space) is an international collaboration of the University of Vienna (Faculty of Sport Science, Department of Sport and Exercise Physiology), the Russian Academy of Sciences (Institute of Biomedical Problems) and the Technical University of Vienna (Institute for Engineering Design and Logistics Engineering) with the aim to develop a training and diagnostic device that counteracts the muscle and bone loss during long term space flights. Due to the scientific results of the last years research in space medicine, it is well known, that the muscles and bones of the lower extremities and the trunk are most affected by the atrophy. Based on this knowledge a various number of resistance exercises can be done in order to train the muscles of these parts of the body and to increase the efficiency of the training by intra- and intermuscular coordination. The resisting power for the training is provided by an electric motor, thereby force, position and speed of the training can be well-regulated for different training modes.

  6. A Novel Strategy to Eliminate the Influence of Water Adsorption on Quartz Surfaces on Piezoelectric Dynamometers.

    Science.gov (United States)

    Jia, Zhenyuan; Jin, Lei; Liu, Wei; Ren, Zongjin

    2016-07-08

    Piezoelectric dynamometers are out of use in high humidity. Experimental results showed that piezoelectric coefficients measured by the force-induced charges method initially fluctuated in a small range and then was unstable, and they could not be measured at high relative humidity (RH). The traditional shielding method-insulation paste was not quiet convenient, and it even added the weight of piezoelectric dynamometers. In this paper, a novel strategy that eliminates the influence of water adsorption with quartz surfaces on piezoelectric dynamometers was proposed. First, a water-quartz model was developed to analyze the origin of the RH effect. In the model, water vapor, which was adsorbed by the quartz sheet side surface, was considered. Second, equivalent sheet resistor of the side surface was researched, while the relationship of the three R's (Roughness, RH, and Resistor) was respectively discussed based on the adsorption mechanism. Finally, fluorination technology was skillfully adapted to each surface of quartz sheets to shield the water vapor. The experiment verified the fluorination strategy and made piezoelectric dynamometers work in high humidity up to 90%RH successfully. The results showed that the presented model above was reasonable. In addition, these observations also drew some useful insights to change the structure of piezoelectric dynamometers and improve the properties.

  7. Design, Construction and Test of a Three-point Hitch Dynamometer

    Directory of Open Access Journals (Sweden)

    M Askari

    2011-09-01

    Full Text Available For measuring the draft forces exerted by implements into tractor, we use the dynamometers that are divided into pull type or three-point hitch type. For measuring the forces between the tractor and the mounted implements, three-point hitch dynamometers are used. In this research, an adjustable three-point hitch dynamometer with a draft capacity of 25 kN was designed and built which is made up from two frames that one of them placed inside the other. The force sensing elements were comprised of a loadcell that was installed between the frames. All mounted tillage implements were able to be tested by this measuring device excluding mounted implements which are powered by PTO and by using this dynamometer, the variations of implements draft force in the different tillage conditions consist of the various work depths and different forward speeds would be studied. After design and construction steps, dynamometer was calibrated, tested and evaluated. Field tests were done by using of four mounted tillage implements and obtained data were compared by obtained data from ASAE D497.5 standard formula. So with these data, the design of tines, their stems, equipment frames and the selection of the optimal size of the tillage equipments in regard of the soil type of the region and the power of the available tractors will be more scientific and reasonable.

  8. Hand Anatomy

    Science.gov (United States)

    ... Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is a Hand Surgeon? What is a Hand Therapist? Media Find a Hand Surgeon Home Anatomy Bones Joints Muscles Nerves Vessels Tendons Anatomy The upper extremity is ...

  9. Android Hands

    DEFF Research Database (Denmark)

    Vlachos, Evgenios; Schärfe, Henrik

    2014-01-01

    . On such occasions, android and humanoid hand models should have similar structure, functions, and performance as the human hand. In this paper we present the anatomy, and the key functionalities of the human hand followed by a literature review on android/humanoid hands for grasping and manipulating objects...

  10. HYDRAULICS, LOUISA COUNTY, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulic data include spatial datasets and data tables necessary for documenting the hydraulic analysis for estimating flood stages for a flood insurance study. It...

  11. Hydraulic Hybrid Vehicles

    Science.gov (United States)

    EPA and the United Parcel Service (UPS) have developed a hydraulic hybrid delivery vehicle to explore and demonstrate the environmental benefits of the hydraulic hybrid for urban pick-up and delivery fleets.

  12. Universal asymptotic umbrella for hydraulic fracture modeling

    CERN Document Server

    Linkov, Aleksandr M

    2014-01-01

    The paper presents universal asymptotic solution needed for efficient modeling of hydraulic fractures. We show that when neglecting the lag, there is universal asymptotic equation for the near-front opening. It appears that apart from the mechanical properties of fluid and rock, the asymptotic opening depends merely on the local speed of fracture propagation. This implies that, on one hand, the global problem is ill-posed, when trying to solve it as a boundary value problem under a fixed position of the front. On the other hand, when properly used, the universal asymptotics drastically facilitates solving hydraulic fracture problems (both analytically and numerically). We derive simple universal asymptotics and comment on their employment for efficient numerical simulation of hydraulic fractures, in particular, by well-established Level Set and Fast Marching Methods.

  13. Effects of Isometric Hand-Grip Muscle Contraction on Young Adults' Free Recall and Recognition Memory

    Science.gov (United States)

    Tomporowski, Phillip D.; Albrecht, Chelesa; Pendleton, Daniel M.

    2017-01-01

    Purpose: The purpose of this study was to determine if physical arousal produced by isometric hand-dynamometer contraction performed during word-list learning affects young adults' free recall or recognition memory. Method: Twenty-four young adults (12 female; M[subscript age] = 22 years) were presented with 4 20-item word lists. Moderate arousal…

  14. The design and simulation investigation of a linear alternator dynamometer coupled to a free-piston Stirling engine

    Science.gov (United States)

    Goldberg, L. F.; Lee, K. P.

    1985-12-01

    The design of a linear alternator dynamometer and its control system intended for testing free-piston Stirling engines is described. The characteristics and performance of the dynamometer are demonstrated by a computer simulation in which the dynamometer is coupled to a Sunpower RE1000 free-piston engine. The simulation embodies algorithms which combine the gas dynamics of the engine working spaces with the dynamic behavior of the displacer and the piston/armature assembly. Over a variety of different loading conditions including inertial, gravitational and thermodynamic loads as well as linear, quadratic and Coulombic damping, the dynamometer exhibited a force error of 0.5 percent or 0.006 N at worst. The simulation investigation demonstrates that the dynamometer and its control system possess the necessary characteristics for it to be a practically useful loading device for testing and designing free-piston Stirling engines.

  15. A Triple-Masked, Randomized Controlled Trial Comparing Ultrasound-Guided Brachial Plexus and Distal Peripheral Nerve Block Anesthesia for Outpatient Hand Surgery

    Directory of Open Access Journals (Sweden)

    Nicholas C. K. Lam

    2014-01-01

    Full Text Available Background. For hand surgery, brachial plexus blocks provide effective anesthesia but produce undesirable numbness. We hypothesized that distal peripheral nerve blocks will better preserve motor function while providing effective anesthesia. Methods. Adult subjects who were scheduled for elective ambulatory hand surgery under regional anesthesia and sedation were recruited and randomly assigned to receive ultrasound-guided supraclavicular brachial plexus block or distal block of the ulnar and median nerves. Each subject received 15 mL of 1.5% mepivacaine at the assigned location with 15 mL of normal saline injected in the alternate block location. The primary outcome (change in baseline grip strength measured by a hydraulic dynamometer was tested before the block and prior to discharge. Subject satisfaction data were collected the day after surgery. Results. Fourteen subjects were enrolled. Median (interquartile range [IQR] strength loss in the distal group was 21.4% (14.3, 47.8%, while all subjects in the supraclavicular group lost 100% of their preoperative strength, P = 0.001. Subjects in the distal group reported greater satisfaction with their block procedures on the day after surgery, P = 0.012. Conclusion. Distal nerve blocks better preserve motor function without negatively affecting quality of anesthesia, leading to increased patient satisfaction, when compared to brachial plexus block.

  16. Hand Fractures

    Science.gov (United States)

    ... Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is a Hand Surgeon? What is ... serve as a framework. This framework supports the muscles that make the wrist ... When one of these hand bones is broken (fractured), it can prevent you ...

  17. 40 CFR 86.137-94 - Dynamometer test run, gaseous and particulate emissions.

    Science.gov (United States)

    2010-07-01

    ... such that the system meets the design criteria of § 86.109 and § 86.110. For samples in which the... necessary. (iv) For formaldehyde samples, the flow rates shall be set such that the system meets the design... according to the Urban Dynamometer Driving Schedule (§ 86.115). Note: During particulate testing, adjust the...

  18. 40 CFR 86.237-08 - Dynamometer test run, gaseous emissions.

    Science.gov (United States)

    2010-07-01

    ... such that the system meets the design criteria of § 86.109 and § 86.110. For samples in which the... necessary. (iv) For formaldehyde samples, the flow rates shall be set such that the system meets the design... the driving schedule. (11) Operate the vehicle according to the Urban Dynamometer Driving Schedule...

  19. 40 CFR 86.884-7 - Dynamometer operation cycle for smoke emission tests.

    Science.gov (United States)

    2010-07-01

    ... preselected dynamometer load, shall be used to control the acceleration of the engine so that the speed increases to 85 percent of the rated speed in 5 ±1.5 seconds. This acceleration shall be linear within 100... acceleration shall be three seconds or less measured from the point where the speed first begins to...

  20. Sensitivity of dynamic simulations of gait and dynamometer experiments to hill muscle model parameters of knee flexors and extensors.

    Science.gov (United States)

    De Groote, F; Van Campen, A; Jonkers, I; De Schutter, J

    2010-07-20

    We assessed and compared sensitivities of dynamic simulations to musculotendon (MT) parameters for gait and dynamometer experiments. Our aim with this comparison was to investigate whether dynamometer experiments could provide information about MT-parameters that are important to reliably study MT-function during gait. This would mean that dynamometer experiments could be used to estimate these parameters. Muscle contribution to the joint torque (MT-torque) rather than relative MT-force primarily affects the resulting gait pattern and torque measured by the dynamometer. In contrast to recent studies, therefore, we assessed the sensitivity of the MT-torque, rather than the sensitivity of the relative MT-force. Based on sensitivity of the MT-torque to a parameter perturbation, MT-parameters of the knee flexors and extensors were classified in three categories: low, medium, and high. For gait, classification was based on the average sensitivity during a gait cycle. For isometric and isokinetic dynamometer experiments, classification was based on the highest sensitivity found in the experiments. The calculated muscle contributions to the knee torque during gait and dynamometer experiments had a high sensitivity to only a limited number of MT-parameters of the knee flexors and extensors, suggesting that not all MT-parameters need to be estimated. In general, the highest sensitivity was found for tendon slack length. However, for some muscles the sensitivity to the optimal fibre length or the maximal isometric muscle force was also high or medium. The classification of the individual MT-parameters for gait and dynamometer experiments was largely similar. We therefore conclude that dynamometer experiments provide information about MT-parameters important to reliably study MT-function during gait, so that subject-specific estimates of MT-parameters could be made based on dynamometer experiments.

  1. Learning effect of isokinetic measurements in healthy subjects, and reliability and comparability of Biodex and Lido dynamometers

    DEFF Research Database (Denmark)

    Lund, Hans; Søndergaard, K; Zachariassen, T

    2005-01-01

    The aim of this study was to examine the learning effect during a set of isokinetic measurements, to evaluate the reliability of the Biodex System 3 PRO dynamometer, and to compare the Biodex System 3 PRO and the Lido Active dynamometers on both extension and flexion over the elbow and the knee...... extension (P = 0.18) and elbow extension (P = 0.63). However, elbow flexion showed a 14.8% (95% CI: 11.2-18.4%; P = 0.0001) higher peak torque on Biodex. In conclusion, no learning effect was observed and the Biodex proved to be a highly reliable isokinetic dynamometer. A difference was observed when...

  2. Thermally Actuated Hydraulic Pumps

    Science.gov (United States)

    Jones, Jack; Ross, Ronald; Chao, Yi

    2008-01-01

    Thermally actuated hydraulic pumps have been proposed for diverse applications in which direct electrical or mechanical actuation is undesirable and the relative slowness of thermal actuation can be tolerated. The proposed pumps would not contain any sliding (wearing) parts in their compressors and, hence, could have long operational lifetimes. The basic principle of a pump according to the proposal is to utilize the thermal expansion and contraction of a wax or other phase-change material in contact with a hydraulic fluid in a rigid chamber. Heating the chamber and its contents from below to above the melting temperature of the phase-change material would cause the material to expand significantly, thus causing a substantial increase in hydraulic pressure and/or a substantial displacement of hydraulic fluid out of the chamber. Similarly, cooling the chamber and its contents from above to below the melting temperature of the phase-change material would cause the material to contract significantly, thus causing a substantial decrease in hydraulic pressure and/or a substantial displacement of hydraulic fluid into the chamber. The displacement of the hydraulic fluid could be used to drive a piston. The figure illustrates a simple example of a hydraulic jack driven by a thermally actuated hydraulic pump. The pump chamber would be a cylinder containing encapsulated wax pellets and containing radial fins to facilitate transfer of heat to and from the wax. The plastic encapsulation would serve as an oil/wax barrier and the remaining interior space could be filled with hydraulic oil. A filter would retain the encapsulated wax particles in the pump chamber while allowing the hydraulic oil to flow into and out of the chamber. In one important class of potential applications, thermally actuated hydraulic pumps, exploiting vertical ocean temperature gradients for heating and cooling as needed, would be used to vary hydraulic pressures to control buoyancy in undersea research

  3. Hand Eczema

    NARCIS (Netherlands)

    Coenraads, Pieter-Jan

    2012-01-01

    A 33-year-old woman presents with redness of the hands and reports the intermittent occurrence of tiny vesicles, scaling, and fissuring, accompanied by itching on the palms, fingers, and dorsal sides of the hands. She has two young children and works as a nurse in a nearby hospital. She has a histor

  4. Vibration of hydraulic machinery

    CERN Document Server

    Wu, Yulin; Liu, Shuhong; Dou, Hua-Shu; Qian, Zhongdong

    2013-01-01

    Vibration of Hydraulic Machinery deals with the vibration problem which has significant influence on the safety and reliable operation of hydraulic machinery. It provides new achievements and the latest developments in these areas, even in the basic areas of this subject. The present book covers the fundamentals of mechanical vibration and rotordynamics as well as their main numerical models and analysis methods for the vibration prediction. The mechanical and hydraulic excitations to the vibration are analyzed, and the pressure fluctuations induced by the unsteady turbulent flow is predicted in order to obtain the unsteady loads. This book also discusses the loads, constraint conditions and the elastic and damping characters of the mechanical system, the structure dynamic analysis, the rotor dynamic analysis and the system instability of hydraulic machines, including the illustration of monitoring system for the instability and the vibration in hydraulic units. All the problems are necessary for vibration pr...

  5. Handbook of hydraulic fluid technology

    CERN Document Server

    Totten, George E

    2011-01-01

    ""The Handbook of Hydraulic Fluid Technology"" serves as the foremost resource for designing hydraulic systems and for selecting hydraulic fluids used in engineering applications. Featuring new illustrations, data tables, as well as practical examples, this second edition is updated with essential information on the latest hydraulic fluids and testing methods. The detailed text facilitates unparalleled understanding of the total hydraulic system, including important hardware, fluid properties, and hydraulic lubricants. Written by worldwide experts, the book also offers a rigorous overview of h

  6. Torsional Vibration in the National Wind Technology Center’s 2.5-Megawatt Dynamometer

    Energy Technology Data Exchange (ETDEWEB)

    Sethuraman, Latha [National Renewable Energy Lab. (NREL), Golden, CO (United States); Keller, Jonathan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Wallen, Robb [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-08-31

    This report documents the torsional drivetrain dynamics of the NWTC's 2.5-megawatt dynamometer as identified experimentally and as calculated using lumped parameter models using known inertia and stiffness parameters. The report is presented in two parts beginning with the identification of the primary torsional modes followed by the investigation of approaches to damp the torsional vibrations. The key mechanical parameters for the lumped parameter models and justification for the element grouping used in the derivation of the torsional modes are presented. The sensitivities of the torsional modes to different test article properties are discussed. The oscillations observed from the low-speed and generator torque measurements were used to identify the extent of damping inherently achieved through active and passive compensation techniques. A simplified Simulink model of the dynamometer test article integrating the electro-mechanical power conversion and control features was established to emulate the torque behavior that was observed during testing. The torque response in the high-speed, low-speed, and generator shafts were tested and validated against experimental measurements involving step changes in load with the dynamometer operating under speed-regulation mode. The Simulink model serves as a ready reference to identify the torque sensitivities to various system parameters and to explore opportunities to improve torsional damping under different conditions.

  7. Bilateral Strength Deficit Is Not Neural in Origin; Rather Due to Dynamometer Mechanical Configuration.

    Science.gov (United States)

    Simoneau-Buessinger, Emilie; Leteneur, Sébastien; Toumi, Anis; Dessurne, Alexandra; Gabrielli, François; Barbier, Franck; Jakobi, Jennifer M

    2015-01-01

    During maximal contractions, the sum of forces exerted by homonymous muscles unilaterally is typically higher than the sum of forces exerted by the same muscles bilaterally. However, the underlying mechanism(s) of this phenomenon, which is known as the bilateral strength deficit, remain equivocal. One potential factor that has received minimal attention is the contribution of body adjustments to bilateral and unilateral force production. The purpose of this study was to evaluate the plantar-flexors in an innovative dynamometer that permitted the influence of torque from body adjustments to be adapted. Participants were identically positioned between two setup configurations where torques generated from body adjustments were included within the net ankle torque (locked-unit) or independent of the ankle (open-unit). Twenty healthy adult males performed unilateral and bilateral maximal voluntary isometric plantar-flexion contractions using the dynamometer in the open and locked-unit mechanical configurations. While there was a significant bilateral strength deficit in the locked-unit (p = 0.01), it was not evident in the open-unit (p = 0.07). In the locked-unit, unilateral torque was greater than in the open-unit (p0.05). This study revealed that the mechanical configuration of the dynamometer and then the body adjustments caused the observation of a bilateral strength deficit.

  8. Bilateral Strength Deficit Is Not Neural in Origin; Rather Due to Dynamometer Mechanical Configuration.

    Directory of Open Access Journals (Sweden)

    Emilie Simoneau-Buessinger

    Full Text Available During maximal contractions, the sum of forces exerted by homonymous muscles unilaterally is typically higher than the sum of forces exerted by the same muscles bilaterally. However, the underlying mechanism(s of this phenomenon, which is known as the bilateral strength deficit, remain equivocal. One potential factor that has received minimal attention is the contribution of body adjustments to bilateral and unilateral force production. The purpose of this study was to evaluate the plantar-flexors in an innovative dynamometer that permitted the influence of torque from body adjustments to be adapted. Participants were identically positioned between two setup configurations where torques generated from body adjustments were included within the net ankle torque (locked-unit or independent of the ankle (open-unit. Twenty healthy adult males performed unilateral and bilateral maximal voluntary isometric plantar-flexion contractions using the dynamometer in the open and locked-unit mechanical configurations. While there was a significant bilateral strength deficit in the locked-unit (p = 0.01, it was not evident in the open-unit (p = 0.07. In the locked-unit, unilateral torque was greater than in the open-unit (p0.05. This study revealed that the mechanical configuration of the dynamometer and then the body adjustments caused the observation of a bilateral strength deficit.

  9. Measurement of muscle strength with handheld dynamometer in Intensive Care Unit

    Directory of Open Access Journals (Sweden)

    Nidhi R Samosawala

    2016-01-01

    Full Text Available Background: Intensive Care Unit (ICU acquired weakness is a common complication in critically ill patients affecting their prognosis. The handheld dynamometry is an objective method in detecting minimum muscle strength change, which has an impact on the physical function of ICU survivors. The minimal change in the force can be measured in units of weight such as pounds or kilograms. Aim of the Study: To detect the changes in peripheral muscle strength with handheld dynamometer in the early stage of ICU stay and to observe the progression of muscle weakness. Methodology: Three upper and three lower limb muscles force measured with handheld dynamometer during ICU stay. Data were analyzed using repeated measures ANOVA to detect changes in force generated by muscle on alternate days of ICU stay. Results: There was a reduction in peripheral muscle strength from day 3 to day 5 as well from day 5 to day 7 of ICU stay (P < 0.01. The average reduction in peripheral muscle strength was 11.8% during ICU stay. Conclusion: This study showed a progressive reduction in peripheral muscle strength as measured by handheld dynamometer during early period of ICU stay.

  10. Hand eczema.

    Science.gov (United States)

    Agarwal, Uma Shankar; Besarwal, Raj Kumar; Gupta, Rahul; Agarwal, Puneet; Napalia, Sheetal

    2014-05-01

    Hand eczema is often a chronic, multifactorial disease. It is usually related to occupational or routine household activities. Exact etiology of the disease is difficult to determine. It may become severe enough and disabling to many of patients in course of time. An estimated 2-10% of population is likely to develop hand eczema at some point of time during life. It appears to be the most common occupational skin disease, comprising 9-35% of all occupational diseases and up to 80% or more of all occupational contact dermatitis. So, it becomes important to find the exact etiology and classification of the disease and to use the appropriate preventive and treatment measures. Despite its importance in the dermatological practice, very few Indian studies have been done till date to investigate the epidemiological trends, etiology, and treatment options for hand eczema. In this review, we tried to find the etiology, epidemiology, and available treatment modalities for chronic hand eczema patients.

  11. Hand functioning in children with cerebral palsy

    Directory of Open Access Journals (Sweden)

    Carlyne eArnould

    2014-04-01

    Full Text Available Brain lesions may disturb hand functioning in children with cerebral palsy (CP, making it difficult or even impossible for them to perform several manual activities. Most conventional treatments for hand dysfunction in CP assume that reducing the hand dysfunctions will improve the capacity to manage activities (i.e., manual ability, MA. The aim of this study was to investigate the directional relationships (direct and indirect pathways through which hand skills influence MA in children with CP. A total of 136 children with CP (mean age: 10 years; range: 6–16 years; 35 quadriplegics, 24 diplegics, 77 hemiplegics were assessed. Six hand skills were measured on both hands: touch-pressure detection (Semmes-Weinstein aesthesiometer, stereognosis (Manual Form Perception Test, proprioception (passive mobilization of the metacarpophalangeal joints, grip strength (Jamar dynamometer, gross manual dexterity (Box and Block Test, and fine finger dexterity (Purdue Pegboard Test. MA was measured with the ABILHAND-Kids questionnaire. Correlation coefficients were used to determine the linear associations between observed variables. A path analysis of structural equation modeling was applied to test different models of causal relationships among the observed variables. Purely sensory impairments did seem not to play a significant role in the capacity to perform manual activities. According to path analysis, gross manual dexterity in both hands and stereognosis in the dominant hand were directly related to MA, whereas grip strength was indirectly related to MA through its relationship with gross manual dexterity. However, one-third of the variance in MA measures could not be explained by hand skills. It can be concluded that MA is not simply the integration of hand skills in daily activities and should be treated per se, supporting activity-based interventions.

  12. Hand Functioning in Children with Cerebral Palsy

    Science.gov (United States)

    Arnould, Carlyne; Bleyenheuft, Yannick; Thonnard, Jean-Louis

    2014-01-01

    Brain lesions may disturb hand functioning in children with cerebral palsy (CP), making it difficult or even impossible for them to perform several manual activities. Most conventional treatments for hand dysfunction in CP assume that reducing the hand dysfunctions will improve the capacity to manage activities (i.e., manual ability, MA). The aim of this study was to investigate the directional relationships (direct and indirect pathways) through which hand skills influence MA in children with CP. A total of 136 children with CP (mean age: 10 years; range: 6–16 years; 35 quadriplegics, 24 diplegics, 77 hemiplegics) were assessed. Six hand skills were measured on both hands: touch-pressure detection (Semmes–Weinstein esthesiometer), stereognosis (Manual Form Perception Test), proprioception (passive mobilization of the metacarpophalangeal joints), grip strength (GS) (Jamar dynamometer), gross manual dexterity (GMD) (Box and Block Test), and fine finger dexterity (Purdue Pegboard Test). MA was measured with the ABILHAND-Kids questionnaire. Correlation coefficients were used to determine the linear associations between observed variables. A path analysis of structural equation modeling was applied to test different models of causal relationships among the observed variables. Purely sensory impairments did seem not to play a significant role in the capacity to perform manual activities. According to path analysis, GMD in both hands and stereognosis in the dominant hand were directly related to MA, whereas GS was indirectly related to MA through its relationship with GMD. However, one-third of the variance in MA measures could not be explained by hand skills. It can be concluded that MA is not simply the integration of hand skills in daily activities and should be treated per se, supporting activity-based interventions. PMID:24782821

  13. FEMA DFIRM Hydraulic Structures

    Data.gov (United States)

    Minnesota Department of Natural Resources — This layer and accompanying attribute table is required whenever hydraulic structures are shown in the flood profile. It is also required if levees are shown on the...

  14. Water Hydraulic Systems

    DEFF Research Database (Denmark)

    Conrad, Finn

    2005-01-01

    The paper presents research results using IT-Tools for CAD and dynamic modelling, simulation, analysis, and design of water hydraulic actuators for motion control of machines, lifts, cranes and robots. Matlab/Simulink and CATIA are used as IT-Tools. The contributions include results from on......-going research projects on fluid power and mechatronics based on tap water hydraulic servovalves and linear servo actuators and rotary vane actuators for motion control and power transmission. Development and design a novel water hydraulic rotary vane actuator for robot manipulators. Proposed mathematical...... modelling, control and simulation of a water hydraulic rotary vane actuator applied to power and control a two-links manipulator and evaluate performance. The results include engineering design and test of the proposed simulation models compared with IHA Tampere University’s presentation of research...

  15. Constant-Pressure Hydraulic Pump

    Science.gov (United States)

    Galloway, C. W.

    1982-01-01

    Constant output pressure in gas-driven hydraulic pump would be assured in new design for gas-to-hydraulic power converter. With a force-multiplying ring attached to gas piston, expanding gas would apply constant force on hydraulic piston even though gas pressure drops. As a result, pressure of hydraulic fluid remains steady, and power output of the pump does not vary.

  16. [Hand infections].

    Science.gov (United States)

    Schiele, Philippe; Le Nen, Dominique

    2013-11-01

    Superficial and deep hand infections are frequent in general medical practice. Clinical examination is a crucial step for an adapted provided care. Most of the time, surgery is the only way to heal infections. However, in some cases (like bites), empiric antibiotherapy is first indicated to limit infection. Staphyloccocus aureus as well as Group Beta Streptococcus are the most frequently pathogenes associated with hand infections. Methicillin resistant S. Aureus must always be considered in the diagnoses. Whatever treatment is provided, clinical assessement must be repeated within two days. An early adaquated treatment prevent functional complications and in some cases death of the patients.

  17. Hand eczema

    Directory of Open Access Journals (Sweden)

    Uma Shankar Agarwal

    2014-01-01

    Full Text Available Hand eczema is often a chronic, multifactorial disease. It is usually related to occupational or routine household activities. Exact etiology of the disease is difficult to determine. It may become severe enough and disabling to many of patients in course of time. An estimated 2-10% of population is likely to develop hand eczema at some point of time during life. It appears to be the most common occupational skin disease, comprising 9-35% of all occupational diseases and up to 80% or more of all occupational contact dermatitis. So, it becomes important to find the exact etiology and classification of the disease and to use the appropriate preventive and treatment measures. Despite its importance in the dermatological practice, very few Indian studies have been done till date to investigate the epidemiological trends, etiology, and treatment options for hand eczema. In this review, we tried to find the etiology, epidemiology, and available treatment modalities for chronic hand eczema patients.

  18. Hand Osteoblastoma

    Directory of Open Access Journals (Sweden)

    M. Farzan

    2006-06-01

    Full Text Available Background and Aim: Osteoblastoma is one of the rarest primary bone tumors. Although, small bones of the hands and feet are the third most common location for this tumor, the hand involvement is very rare and few case observations were published in the English-language literature. Materials and Methods: In this study, we report five cases of benign osteoblastoma of the hand, 3 in metacarpals and two in phalanxes. The clinical feature is not specific. The severe nocturnal, salicylate-responsive pain is not present in patients with osteoblastoma. The pain is dull, persistent and less localized. The clinical course is usually long and there is often symptoms for months before medical attention are sought. Swelling is a more persistent finding in osteoblastoma of the hand that we found in all of our patients. The radiologic findings are indistinctive, so preoperative diagnosis based on X-ray appearance is difficult. In all of our 5 cases, we fail to consider osteoblastoma as primary diagnosis. Pathologically, osteoblastoma consisting of a well-vascularized connective tissue stroma in which there is active production of osteoid and primitive woven bone. Treatment depends on the stage and localization of the tumor. Curettage and bone grafting is sufficient in stage 1 or stage 2, but in stage 3 wide resection is necessary for prevention of recurrence. Osteosarcoma is the most important differential diagnosis that may lead to inappropriate operation.

  19. Hand eczema

    DEFF Research Database (Denmark)

    Ibler, K.S.; Jemec, G.B.E.; Flyvholm, M.-A.

    2012-01-01

    /materials/methods. A survey of 3181 healthcare workers was performed. Data were analysed with logistic regression. Data on sick leave and notification to the authorities were obtained. Results. The response rate was 71% (2274 of 3181). The 1-year prevalence of hand eczema was 21%, and was positively associated with atopic...

  20. Magic Hands

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    THE two most amazing things on the planet may well be the human brain and human hands. When they work together, the results can be enchanting. At an international folk art fair held recently in Beijing, artisans and masters from Japan, India, Switzerland, Peru, South

  1. Effects of hyperthyroidism on hand grip strength and function.

    Science.gov (United States)

    Erkol İnal, Esra; Çarlı, Alparslan Bayram; Çanak, Sultan; Aksu, Oğuzhan; Köroğlu, Banu Kale; Savaş, Serpil

    2015-01-01

    Hyperthyroidism is a pathologic condition in which the body is exposed to excessive amounts of circulating thyroid hormones. Skeletal muscle is one of the major target organs of thyroid hormones. We evaluated hand grip strength and function in patients with overt hyperthyroidism. Fifty-one patients newly diagnosed with hyperthyroidism and 44 healthy controls participated in this study. Age, height, weight, and dominant hand of all participants were recorded. The diagnosis of hyperthyroidism was confirmed by clinical examination and laboratory tests. Hand grip strength was tested at the dominant hand with a Jamar hand dynamometer. The grooved pegboard test (PGT) was used to evaluate hand dexterity. The Duruöz Hand Index (DHI) was used to assess hand function. No significant differences were found in terms of clinical and demographic findings between the patients with hyperthyroidism and healthy controls (p > 0.05). Significant differences were found between the patients with hyperthyroidism and healthy controls regarding PGT and DHI scores (p Hyperthyroidism seemed to affect hand dexterity and function more than hand grip strength and seemed to be associated with reduced physical function more than muscle strength. This may also indicate that patients with hyperthyroidism should be evaluated by multidisplinary modalities.

  2. Trend of hydraulic units

    Energy Technology Data Exchange (ETDEWEB)

    Deshimaru, Jun' ichi

    1988-11-01

    The gear, vane and piston pumps occupy a more then 90% share in the hydraulic pumps. Comparatively large pumps are mainly variable delivery piston pumps. The piston pumps are comparatively high in output density (output per unit weight), indicating the hydraulic pump in performance, and tend to become higher and higher in it. Though they are mainly 210 to 350kgf/cm/sup 2/ in rated pressure, some of them come to surpass 400kgf/cm/sup 3/ in it. While the progress in computation also requires the high speed operation, high accuracy and other severe conditions for the hydraulic units, which accordingly and increasingly intensify the requirement for hydraulic oil in abrasion resistibility, oxidation stability and response characteristics. While cavitation comes to easily occur, which considerably and disadvantageously influences hydraulic oil in life through degradation, noise level and respondingness. From now on, the development of high performance oil and study of mechanical structure are important. 19 references, 9 figures, 2 tables.

  3. Cavitation in Hydraulic Machinery

    Energy Technology Data Exchange (ETDEWEB)

    Kjeldsen, M.

    1996-11-01

    The main purpose of this doctoral thesis on cavitation in hydraulic machinery is to change focus towards the coupling of non-stationary flow phenomena and cavitation. It is argued that, in addition to turbulence, superimposed sound pressure fluctuations can have a major impact on cavitation and lead to particularly severe erosion. For the design of hydraulic devices this finding may indicate how to further limit the cavitation problems. Chapter 1 reviews cavitation in general in the context of hydraulic machinery, emphasizing the initial cavitation event and the role of the water quality. Chapter 2 discusses the existence of pressure fluctuations for situations common in such machinery. Chapter 3 on cavitation dynamics presents an algorithm for calculating the nucleation of a cavity cluster. Chapter 4 describes the equipment used in this work. 53 refs., 55 figs.,10 tabs.

  4. Development and testing of an integrated rotating dynamometer on tool holder for milling process

    Science.gov (United States)

    Rizal, Muhammad; Ghani, Jaharah A.; Nuawi, Mohd Zaki; Che Haron, Che Hassan

    2015-02-01

    The cutting force provides significant information to help understand the machining process, optimization, tool condition monitoring, tool design and others. Hence, various methods of measuring the cutting force have been proposed by many researchers. In this work, an innovative integrated rotating dynamometer and tool holder is designed, constructed and tested that can fulfil the requirement to measure the cutting force in a wireless environment system. The device consists of a strain gauge based sensor that is mounted on a newly designed force sensing element which is then placed in the rotating tool holder. The force sensing element is designed in the form of a symmetrical cross beam type with four arms, shaped as a rectangular parallelepiped. This device is intended to be used in a rotating spindle such as in milling and drilling processes. A conditioning system and an inductive telemetry transmitter unit are incorporated into a modified tool holder in order to collect and transmit the cutting force signal to the data acquisition system. The rotating dynamometer has been subjected to a series of tests to determine its static and dynamic characteristics. Thus, it is tested experimentally by conducting cutting tests up to cutting speed 550 m/min with a single-tool insert. The results show it is suitable and reliable to measure the cutting force in milling processes.

  5. Universal Linear Motor Driven Leg Press Dynamometer and Concept of Serial Stretch Loading

    Science.gov (United States)

    2015-01-01

    Paper deals with backgrounds and principles of universal linear motor driven leg press dynamometer and concept of serial stretch loading. The device is based on two computer controlled linear motors mounted to the horizontal rails. As the motors can keep either constant resistance force in selected position or velocity in both directions, the system allows simulation of any mode of muscle contraction. In addition, it also can generate defined serial stretch stimuli in a form of repeated force peaks. This is achieved by short segments of reversed velocity (in concentric phase) or acceleration (in eccentric phase). Such stimuli, generated at the rate of 10 Hz, have proven to be a more efficient means for the improvement of rate of the force development. This capability not only affects performance in many sports, but also plays a substantial role in prevention of falls and their consequences. Universal linear motor driven and computer controlled dynamometer with its unique feature to generate serial stretch stimuli seems to be an efficient and useful tool for enhancing strength training effects on neuromuscular function not only in athletes, but as well as in senior population and rehabilitation patients. PMID:26913159

  6. Universal linear motor driven Leg Press Dynamometer and concept of Serial Stretch Loading

    Directory of Open Access Journals (Sweden)

    Dušan Hamar

    2015-08-01

    Full Text Available Paper deals with backgrounds and principles of universal linear motor driven leg press dynamometer and concept of serial stretch loading. The device is based on two computer controlled linear motors mounted to the horizontal rails. As the motors can keep either constant resistance force in selected position or velocity in both directions, the system allows simulation of any mode of muscle contraction. In addition, it also can generate defined serial stretch stimuli in a form of repeated force peaks. This is achieved by short segments of reversed velocity (in concentric phase or acceleration (in eccentric phase. Such stimuli, generated at the rate of 10 Hz, have proven to be a more efficient means for the improvement of rate of the force development. This capability not only affects performance in many sports, but also plays a substantial role in prevention of falls and their consequences. Universal linear motor driven and computer controlled dynamometer with its unique feature to generate serial stretch stimuli seems to be an efficient and useful tool for enhancing strength training effects on neuromuscular function not only in athletes, but as well as in senior population and rehabilitation patients.

  7. Wind-electric icemaking project: Analysis and dynamometer testing. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Holz, R; Gervorgian, V; Drouilhet, S; Muljadi, E

    1998-07-01

    The wind/hybrid systems group at the National Renewable Energy Laboratory has been researching the most practical and cost-effective methods for producing ice from off-grid wind-electric power systems. The first phase of the project, conducted in 1993--1994, included full-scale dynamometer and field testing of two different electric ice makers directly connected to a permanent magnet alternator. The results of that phase were encouraging and the second phase of the project was launched in which steady-state and dynamic numerical models of these systems were developed and experimentally validated. The third phase of the project was the dynamometer testing of the North Star ice maker, which is powered by a 12-kilowatt Bergey Windpower Company, Inc., alternator. This report describes both the second and third project phases. Also included are detailed economic analyses and a discussion of the future prospects of wind-electric ice-making systems. The main report is contained in Volume 1. Volume 2 consists of the report appendices, which include the actual computer programs used in the analysis and the detailed test results.

  8. Comparing different approaches for determining joint torque parameters from isovelocity dynamometer measurements.

    Science.gov (United States)

    Forrester, S E; Yeadon, M R; King, M A; Pain, M T G

    2011-03-15

    Strength, or maximum joint torque, is a fundamental factor governing human movement, and is regularly assessed for clinical and rehabilitative purposes as well as for research into human performance. This study aimed to identify the most appropriate protocol for fitting a maximum voluntary torque function to experimental joint torque data. Three participants performed maximum isometric and concentric-eccentric knee extension trials on an isovelocity dynamometer and a separate experimental protocol was used to estimate maximum knee extension angular velocity. A nine parameter maximum voluntary torque function, which included angle, angular velocity and neural inhibition effects, was fitted to the experimental torque data and three aspects of this fitting protocol were investigated. Using an independent experimental estimate of maximum knee extension angular velocity gave lower variability in the high concentric velocity region of the maximum torque function compared to using dynamometer measurements alone. A weighted root mean square difference (RMSD) score function, that forced the majority (73-92%) of experimental data beneath the maximum torque function, was found to best account for the one-sided noise in experimental torques resulting from sub-maximal effort by the participants. The suggested protocol (an appropriately weighted RMSD score function and an independent estimate of maximum knee extension angular velocity) gave a weighted RMSD of between 11 and 13 Nm (4-5% of maximum isometric torque). It is recommended that this protocol be used in generating maximum voluntary joint torque functions in all torque-based modelling of dynamic human movement.

  9. Hydraulics and pneumatics

    CERN Document Server

    Parr, Andrew

    2006-01-01

    Nearly all industrial processes require objects to be moved, manipulated or subjected to some sort of force. This is frequently accomplished by means of electrical equipment (such as motors or solenoids), or via devices driven by air (pneumatics) or liquids (hydraulics).This book has been written by a process control engineer as a guide to the operation of hydraulic and pneumatic systems for all engineers and technicians who wish to have an insight into the components and operation of such a system.This second edition has been fully updated to include all recent developments su

  10. Popeye Project: Hydraulic umbilical

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, K.G.; Williams, V.T.

    1996-12-31

    For the Popeye Project, the longest super-duplex hydraulic umbilical in the world was installed in the Gulf of Mexico. This paper reports on its selection and project implementation. Material selection addresses corrosion in seawater, water-based hydraulic fluid, and methanol. Five alternatives were considered: (1) carbon-steel with traditional coating and anodes, (2) carbon-steel coated with thermally sprayed aluminum, (3) carbon-steel sheathed in aluminum, (4) super-duplex, and (5) titanium. The merits and risks associated with each alternative are discussed. The manufacture and installation of the selected umbilical are also reported.

  11. Hydraulic Arm Modeling via Matlab SimHydraulics

    OpenAIRE

    Věchet, Stanislav; Krejsa, Jiří

    2009-01-01

    System modeling is a vital tool for cost reduction and design process speed up in most engineering fields. The paper is focused on modeling of hydraulic arm as a part of intelligent prosthesis project, in the form of 2DOF open kinematic chain. The arm model combines mechanical, hydraulic and electric subsystems and uses Matlab as modeling tool. SimMechanics Matlab extension is used for mechanical part modeling, SimHydraulics toolbox is used for modeling of hydraulic circuit used for actuating...

  12. Reliability of Concentric, Eccentric and Isometric Knee Extension and Flexion when using the REV9000 Isokinetic Dynamometer

    DEFF Research Database (Denmark)

    de Carvalho Froufe Andrade, Alberto César Pereira; Caserotti, Paolo; de Carvalho, Carlos Manuel Pereira

    2013-01-01

    The aim of this study was to assess the reliability of isokinetic and ISO knee extensor and flexor muscle strength when using the REV9000 (Technogym) isokinetic dynamometer. Moreover, the reliability of several strength imbalance indices and bilateral ratios were also examined. Twenty......). The results of this study showed a high reproducibility in eccentric (0.95-0.97), concentric (0.95-0.96) and isometric (0.93-0.96), isokinetic strength for knee extensor and flexor muscles, thus indicating that the REV9000 isokinetic dynamometer can be used in future sports performance studies. A low...

  13. HYDRAULICS, TUSCARAWAS COUNTY, OHIO, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulic data include spatial datasets and data tables necessary for documenting the hydraulic procedures for estimating flood discharges for a flood insurance...

  14. Circuit For Control Of Electromechanical Prosthetic Hand

    Science.gov (United States)

    Bozeman, Richard J., Jr.

    1995-01-01

    Proposed circuit for control of electromechanical prosthetic hand derives electrical control signals from shoulder movements. Updated, electronic version of prosthesis, that includes two hooklike fingers actuated via cables from shoulder harness. Circuit built around favored shoulder harness, provides more dexterous movement, without incurring complexity of computer-controlled "bionic" or hydraulically actuated devices. Additional harness and potentiometer connected to similar control circuit mounted on other shoulder. Used to control stepping motor rotating hand about prosthetic wrist to one of number of angles consistent with number of digital outputs. Finger-control signals developed by circuit connected to first shoulder harness transmitted to prosthetic hand via sliprings at prosthetic wrist joint.

  15. Hydraulic hoist-press

    Energy Technology Data Exchange (ETDEWEB)

    Babayev, Z.B.; Abashev, Z.V.

    1982-01-01

    The efficiency expert of the Angrenskiy production-technological administration of the production association Sredazugol A. V. Bubnov has suggested a hydraulic hoist-press for repairing road equipment which is a device consisting of lifting mechanism, press and test stand for verifying the high pressure hoses and pumps.

  16. Modelling of Hydraulic Robot

    DEFF Research Database (Denmark)

    Madsen, Henrik; Zhou, Jianjun; Hansen, Lars Henrik

    1997-01-01

    This paper describes a case study of identifying the physical model (or the grey box model) of a hydraulic test robot. The obtained model is intended to provide a basis for model-based control of the robot. The physical model is formulated in continuous time and is derived by application...

  17. Water Treatment Technology - Hydraulics.

    Science.gov (United States)

    Ross-Harrington, Melinda; Kincaid, G. David

    One of twelve water treatment technology units, this student manual on hydraulics provides instructional materials for three competencies. (The twelve units are designed for a continuing education training course for public water supply operators.) The competencies focus on the following areas: head loss in pipes in series, function loss in…

  18. Water Hydraulic Systems

    DEFF Research Database (Denmark)

    Conrad, Finn

    2005-01-01

    The paper presents research results using IT-Tools for CAD and dynamic modelling, simulation, analysis, and design of water hydraulic actuators for motion control of machines, lifts, cranes and robots. Matlab/Simulink and CATIA are used as IT-Tools. The contributions include results from on-going...

  19. Dynamometer Elbow Strength and Endurance Testing After Distal Biceps Reconstruction w/Allograft

    Science.gov (United States)

    McGee, Alan; Strauss, Eric Jason; Jazrawi, Laith M.

    2015-01-01

    Objectives: The purpose of the current study is to investigate the functional strength outcomes of late distal biceps reconstruction using allograft tissue. Methods: Patients who underwent distal biceps reconstruction with allograft tissue between May 2007 and May 2013 were identified. Charts were retrospectively reviewed for post-operative complications, gross flexion and supination strength, and range of motion (ROM). Isokinetic strength and endurance in elbow flexion and forearm supination were measured in both arms. Tests were conducted using a dynamometer at 60o per second for isokinetic strength and 240o per second for endurance. Isometric strength testing was also measured for elbow flexion and forearm supination. Paired t tests were used for statistical analysis. Results: Ten patients with a mean age of 48 years (range 42 - 61 years) were included in the study. Distal biceps reconstruction was performed using an Achilles tendon allograft in 9 patients and a combination of tibialis anterior allograft and gracilis allograft in 1 patient. Of the reconstructions, 50% involved the dominant arm. Full ROM was observed in all patients at the time of their final follow up assessment. The mean follow-up for dynamometer strength testing was 34 months (range 13-81 months). No statistical differences were noted between data obtained from operative and contralateral extremities. The average peak torque of the operative limb (38.5± 5.9 Nm) was 91.7% of that of the contralateral limb (41.8±4.9 Nm) in flexion and 93.4% (operative, 5.7±1.3 Nm; contralateral, 6.1± 1.0 Nm) in supination. No significant differences were found in fatigue index between operative or contralateral limbs for flexion (operative, 34.1±17.1%; contralateral, 30.8±17.1%; p = 0.29) or supination (operative, 38.2±16.5%; contralateral, 42.1±11.9%; p = 0.65). . The only complication observed was a transient PIN palsy in one patient which resolved by 3 months post-operatively. All patients reported

  20. Hydraulic manipulator research at ORNL

    Energy Technology Data Exchange (ETDEWEB)

    Kress, R.L.; Jansen, J.F. [Oak Ridge National Lab., TN (United States); Love, L.J. [Oak Ridge Inst. for Science and Education, TN (United States)

    1997-03-01

    Recently, task requirements have dictated that manipulator payload capacity increase to accommodate greater payloads, greater manipulator length, and larger environmental interaction forces. General tasks such as waste storage tank cleanup and facility dismantlement and decommissioning require manipulator life capacities in the range of hundreds of pounds rather than tens of pounds. To meet the increased payload capacities demanded by present-day tasks, manipulator designers have turned once again to hydraulics as a means of actuation. In order to successfully design, build, and deploy a new hydraulic manipulator (or subsystem), sophisticated modeling, analysis, and control experiments are usually needed. Oak Ridge National Laboratory (ORNL) has a history of projects that incorporate hydraulics technology, including mobile robots, teleoperated manipulators, and full-scale construction equipment. In addition, to support the development and deployment of new hydraulic manipulators, ORNL has outfitted a significant experimental laboratory and has developed the software capability for research into hydraulic manipulators, hydraulic actuators, hydraulic systems, modeling of hydraulic systems, and hydraulic controls. The purpose of this article is to describe the past hydraulic manipulator developments and current hydraulic manipulator research capabilities at ORNL. Included are example experimental results from ORNL`s flexible/prismatic test stand.

  1. Space-borne gravitational wave detectors as time-delayed differential dynamometers

    CERN Document Server

    Congedo, Giuseppe; Hueller, Mauro; Vitale, Stefano; Weber, William J

    2013-01-01

    The basic constituent of many space-borne gravitational missions, in particular for interferometric gravitational waves detectors, is the so-called link made out of a satellite sending an electromagnetic beam to a second satellite. We illustrate how, by measuring the time derivative of the frequency of the received beam, the link behaves as a differential, time-delayed dynamometer in which the effect of gravity is exactly equivalent to an effective differential force applied to the two satellites. We also show that this differential force gives an integrated measurement of curvature along the beam. Finally, we discuss how this approach can be implemented to benefit the data analysis of gravitational wave detectors.

  2. Eddy current analysis of permanent magnet dynamometers; Eikyu jishakushiki dinamo meter no kadenryu kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-02-29

    The ultra-low inertia dynamometer equivalent to engines in inertia adopts a rare earth element magnet with large energy product, and simulates engine torque fluctuation by superimposing harmonic current on a stator coil. Since temperature rise is thus predicted by generation of fluctuating magnetic field due to the harmonic current or eddy current due to normal slot harmonics, sufficient study on eddy current loss is necessary for designs to prevent such performance drop. Eddy current analysis is under investigation by 3-D FEM for various size and shape magnets. The analysis example of an eddy current density distribution is illustrated for the one-pole section of the magnet stuck on a rotor surface which is divided into 4 parts along a rotor periphery. More precise analysis of such eddy current loss is scheduled for higher-reliability product design. (translated by NEDO)

  3. Remotely Adjustable Hydraulic Pump

    Science.gov (United States)

    Kouns, H. H.; Gardner, L. D.

    1987-01-01

    Outlet pressure adjusted to match varying loads. Electrohydraulic servo has positioned sleeve in leftmost position, adjusting outlet pressure to maximum value. Sleeve in equilibrium position, with control land covering control port. For lowest pressure setting, sleeve shifted toward right by increased pressure on sleeve shoulder from servovalve. Pump used in aircraft and robots, where hydraulic actuators repeatedly turned on and off, changing pump load frequently and over wide range.

  4. Undular Hydraulic Jump

    Directory of Open Access Journals (Sweden)

    Oscar Castro-Orgaz

    2015-04-01

    Full Text Available The transition from subcritical to supercritical flow when the inflow Froude number Fo is close to unity appears in the form of steady state waves called undular hydraulic jump. The characterization of the undular hydraulic jump is complex due to the existence of a non-hydrostatic pressure distribution that invalidates the gradually-varied flow theory, and supercritical shock waves. The objective of this work is to present a mathematical model for the undular hydraulic jump obtained from an approximate integration of the Reynolds equations for turbulent flow assuming that the Reynolds number R is high. Simple analytical solutions are presented to reveal the physics of the theory, and a numerical model is used to integrate the complete equations. The limit of application of the theory is discussed using a wave breaking condition for the inception of a surface roller. The validity of the mathematical predictions is critically assessed using physical data, thereby revealing aspects on which more research is needed

  5. Hydraulic System Design of Hydraulic Actuators for Large Butterfly Valves

    OpenAIRE

    HUANG, Ye; Liu, Changsheng; Shiongur Bamed

    2014-01-01

    Hydraulic control systems of butterfly valves are presently valve-controlled and pump-controlled. Valve-controlled hydraulic systems have serious power loss and generate much heat during throttling. Pump-controlled hydraulic systems have no overflow or throttling losses but are limited in the speed adjustment of the variable-displacement pump, generate much noise, pollute the environment, and have motor power that does not match load requirements, resulting in low efficiency under...

  6. Hydraulic System Design of Hydraulic Actuators for Large Butterfly Valves

    Directory of Open Access Journals (Sweden)

    Ye HUANG

    2014-09-01

    Full Text Available Hydraulic control systems of butterfly valves are presently valve-controlled and pump-controlled. Valve-controlled hydraulic systems have serious power loss and generate much heat during throttling. Pump-controlled hydraulic systems have no overflow or throttling losses but are limited in the speed adjustment of the variable-displacement pump, generate much noise, pollute the environment, and have motor power that does not match load requirements, resulting in low efficiency under light loads and wearing of the variable-displacement pump. To overcome these shortcomings, this article designs a closed hydraulic control system in which an AC servo motor drives a quantitative pump that controls a spiral swinging hydraulic cylinder, and analyzes and calculates the structure and parameters of a spiral swinging hydraulic cylinder. The hydraulic system adjusts the servo motor’s speed according to the requirements of the control system, and the motor power matches the power provided to components, thus eliminating the throttling loss of hydraulic circuits. The system is compact, produces a large output force, provides stable transmission, has a quick response, and is suitable as a hydraulic control system of a large butterfly valve.

  7. Modelling of Hydraulic Robot

    DEFF Research Database (Denmark)

    Madsen, Henrik; Zhou, Jianjun; Hansen, Lars Henrik

    1997-01-01

    This paper describes a case study of identifying the physical model (or the grey box model) of a hydraulic test robot. The obtained model is intended to provide a basis for model-based control of the robot. The physical model is formulated in continuous time and is derived by application...... of the laws of physics on the system. The unknown (or uncertain) parameters are estimated with Maximum Likelihood (ML) parameter estimation. The identified model has been evaluated by comparing the measurements with simulation of the model. The identified model was much more capable of describing the dynamics...... of the system than the deterministic model....

  8. Hydraulic mining method

    Science.gov (United States)

    Huffman, Lester H.; Knoke, Gerald S.

    1985-08-20

    A method of hydraulically mining an underground pitched mineral vein comprising drilling a vertical borehole through the earth's lithosphere into the vein and drilling a slant borehole along the footwall of the vein to intersect the vertical borehole. Material is removed from the mineral vein by directing a high pressure water jet thereagainst. The resulting slurry of mineral fragments and water flows along the slant borehole into the lower end of the vertical borehole from where it is pumped upwardly through the vertical borehole to the surface.

  9. Spinning hydraulic jump

    Science.gov (United States)

    Abderrahmane, Hamid; Kasimov, Aslan

    2013-11-01

    We report an experimental observation of a new symmetry breaking of circular hydraulic jump into a self-organized structure that consists of a spinning polygonal jump and logarithmic-spiral waves of fluid elevation downstream. The waves are strikingly similar to spiral density waves in galaxies. The fluid flow exhibits counterparts of salient morphological features of galactic flows, in particular the outflow from the center, jets, circum-nuclear rings, gas inflows toward the galactic center, and vortices. The hydrodynamic instability revealed here may have a counterpart that plays a role in the formation and sustainability of spiral arms in galaxies.

  10. 46 CFR 28.880 - Hydraulic equipment.

    Science.gov (United States)

    2010-10-01

    ... hydraulic equipment and the adjacent work area. Protection shall be afforded to the operator of hydraulic... 46 Shipping 1 2010-10-01 2010-10-01 false Hydraulic equipment. 28.880 Section 28.880 Shipping... INDUSTRY VESSELS Aleutian Trade Act Vessels § 28.880 Hydraulic equipment. (a) Each hydraulic system must...

  11. Applied hydraulic transients

    CERN Document Server

    Chaudhry, M Hanif

    2014-01-01

    This book covers hydraulic transients in a comprehensive and systematic manner from introduction to advanced level and presents various methods of analysis for computer solution. The field of application of the book is very broad and diverse and covers areas such as hydroelectric projects, pumped storage schemes, water-supply systems, cooling-water systems, oil pipelines and industrial piping systems. Strong emphasis is given to practical applications, including several case studies, problems of applied nature, and design criteria. This will help design engineers and introduce students to real-life projects. This book also: ·         Presents modern methods of analysis suitable for computer analysis, such as the method of characteristics, explicit and implicit finite-difference methods and matrix methods ·         Includes case studies of actual projects ·         Provides extensive and complete treatment of governed hydraulic turbines ·         Presents design charts, desi...

  12. Wrist flexion and extension torques measured by highly sensitive dynamometer in healthy subjects from 5 to 80 years.

    Science.gov (United States)

    Decostre, Valérie; Canal, Aurélie; Ollivier, Gwenn; Ledoux, Isabelle; Moraux, Amélie; Doppler, Valérie; Payan, Christine Anne Mary; Hogrel, Jean-Yves

    2015-01-31

    Wrist movements become impaired with disease progression in various neuromuscular disorders. With the development of new therapies, thorough measurement of muscle strength is crucial to document natural disease progression and to assess treatment efficacy. We developed a new dynamometer enabling wrist flexion and extension torque measurement with high sensitivity. The aims of the present study were to collect norms for healthy children and adults, to compute predictive equations, to assess the reliability of the measurements and to test the feasibility of using the device in patients with a neuromuscular disease. The peak isometric torque of wrist flexion and extension was measured with the MyoWrist dynamometer in 345 healthy subjects aged between 5 and 80 years old and in 9 patients with limb girdle muscle dystrophy type 2 C (LGMD2C) aged between 16 and 38 years old. Predictive equations are proposed for the wrist flexion and extension strength in children and adults. Intra-rater and inter-rater reliability was good with ICCs higher than 0.9 for both wrist flexion and extension. However, retest values were significantly higher by 4% than test results. The dynamometer was applied with no difficulty to patients with LGMD2C and was sensitive enough to detect strength as weak as 0.82 N.m. From our models, we quantified the mean strength of wrist extension in LGMD2C patients to 39 ± 17% of their predicted values. The MyoWrist dynamometer provides reliable and sensitive measurement of both wrist flexion and extension torques. However, a training session is recommended before starting a study as a small but significant learning effect was observed. Strength deficit can be quantified from predictive equations that were computed from norms of healthy children and adults.

  13. Hydraulic rams; a comparative investigation

    NARCIS (Netherlands)

    Tacke, J.H.P.M.

    1988-01-01

    A mathematical model describing the essential features of hydraulic ram operation is developed in order to clarify the possibilities and limitations of the ram relative to its site and its adjustments. The model distinguishes three different periods in the pumping cycle of the hydraulic ram: acceler

  14. Hydraulics. FOS: Fundamentals of Service.

    Science.gov (United States)

    John Deere Co., Moline, IL.

    This manual on hydraulics is one of a series of power mechanics texts and visual aids for training in the servicing of agricultural and industrial machinery. Focus is on oil hydraulics. Materials provide basic information and illustrations for use by vocational students and teachers as well as shop servicemen and laymen. The twelve chapters focus…

  15. A purpose-built dynamometer to objectively measure static and dynamic knee torque.

    Science.gov (United States)

    Ugbolue, U C; Kaliarntas, K T; Wearing, S C; Rowe, P J

    2011-05-01

    This paper reports the development of a purpose-built knee dynamometer (PBKD) to evaluate passive range of motion (ROM) and isometric muscle strength measurements of the knee. The PBKD uses a TorqSense rotary torque transducer and objectively measures isometric knee muscle strength in a valid and reliable manner and passive resistance to motion through range. The device and all associated instrumentation underwent dynamic and static calibration to ensure consistent and accurate measurements were obtained in terms of knee joint angular position, passive torque measures, and isometric torque measures. Eleven healthy male participants performed a knee flexion and extension task designed to evaluate knee function. The validation of the PBKD entailed measuring the consistency of measurement and accuracy of measurement. Accuracy of the PBKD was determined by comparing peak isometric muscle strength measurements against a KIN-COM machine. No significant differences were observed both passively and isometrically between cycles and between trials. This device can have widespread applications within the rehabilitation and clinical environment and could be used as a functional outcome measuring tool to distinguish pathological from non-pathological knees. The presented preliminary results indicate that reliable and accurate measurements of knee ROM and muscle strength can be obtained.

  16. Understanding the effect of speed of exertion on isokinetic strength using a multiaxial dynamometer.

    Science.gov (United States)

    Nimbarte, Ashish D; Aghazadeh, Fereydoun; Bogolu, Sai Chaitanya R; Rajulu, Sudhakar L

    2009-01-01

    In this study a multiaxial isokinetic dynamometer was used to measure strength during various upper-body isokinetic exertions. Ten male participants performed 7 different upper-body isokinetic exertions. In addition, to evaluate the effect of speed on strength, each participant performed sitting pull exertions at the speed of 0.026, 0.130, and 0.260 m/s. Average isokinetic strength increased from 236.6 +/- 39.1 to 291.8 +/- 65.8 N with the initial increase in speed from 0.026 to 0.130 m/s. The average isokinetic strength decreased to 276.7 +/- 87.2 N with a further increase in speed to 0.260 m/s. The curve between isokinetic strength and speed followed a bell-shaped curve (fitted with the Gaussian function, R(2) = .9). The results of this study could be useful in deciding on the work pace of various manual material handling tasks requiring maximal and/or near maximal exertions.

  17. The use of muscle dynamometer for correction of muscle imbalances in the area of deep stabilising spine system.

    Science.gov (United States)

    Malátová, Renata; Rokytová, Jitka; Stumbauer, Jan

    2013-08-01

    Dorsal pain caused by spine dysfunctions belongs to most frequent chronic illnesses. The muscles of the deep stabilising spine system work as a single functional unit where a dysfunction of only one muscle causes dysfunction of the whole system. Non-invasive, objective and statistically measurable evaluation of the condition of deep stabilising spine system has been made possible by the construction of muscular dynamometer. The aim of our work has been the assessment of deep stabilising spine system by diaphragm test and muscular dynamometer measurements. Based on an initial examination, a 6-week intervention programme was established including instructions on physiological body posture and correct basic body stabilisation for the given exercises and muscle strengthening. Consecutive measurements are then compared with the initial ones. It was presumed that a smaller number of the tested subjects would be able to correctly activate the deep stabilising spine system muscles before the intervention programme when compared to those after the intervention programme. A positive change of 87% has been found. It is clear that if a person actively approaches the programme, then positive adaptation changes on the deep stabilising spine system are seen only after 6 weeks. With the muscular dynamometer, activation of deep stabilising spine system can be objectively measured. Changes between the initial condition of a subject and the difference after some exercise or rehabilitation are especially noticeable. Also, the effect of given therapy or correct performance of the exercise can be followed and observed.

  18. Hydraulic Stability of Accropode Armour

    DEFF Research Database (Denmark)

    Jensen, T.; Burcharth, H. F.; Frigaard, Peter

    , and to assess the influence of core permeability on the hydraulic stability of Accropodes. Two structures were examined, one with a relatively permeable core and one with a relatively impermeable core. In November/December 1995, Ph.D.-student Marten Christensen carried out the model tests on the structure...... with permeable core (crushed granite with a gradation of 5-8 mm). The outcome of this study is described in "Hydraulic Stability of Single-Layer Dolos and Accropode Armour Layers" by Christensen & Burcharth (1995). In January/February 1996, Research Assistant Thomas Jensen carried out a similar study......The present report describes the hydraulic model tests of Accropode armour layers carried out at the Hydraulics Laboratory at Aalborg University from November 1995 through March 1996. The objective of the model tests was to investigate the hydraulic stability of Accropode armour layers...

  19. Hydraulic Stability of Accropode Armour

    DEFF Research Database (Denmark)

    Jensen, T.; Burcharth, H. F.; Frigaard, Peter

    , and to assess the influence of core permeability on the hydraulic stability of Accropodes. Two structures were examined, one with a relatively permeable core and one with a relatively impermeable core. In November/December 1995, Ph.D.-student Marten Christensen carried out the model tests on the structure...... with permeable core (crushed granite with a gradation of 5-8 mm). The outcome of this study is described in "Hydraulic Stability of Single-Layer Dolos and Accropode Armour Layers" by Christensen & Burcharth (1995). In January/February 1996, Research Assistant Thomas Jensen carried out a similar study......The present report describes the hydraulic model tests of Accropode armour layers carried out at the Hydraulics Laboratory at Aalborg University from November 1995 through March 1996. The objective of the model tests was to investigate the hydraulic stability of Accropode armour layers...

  20. Effect of anaemia on hand grip strength, walking speed, functionality and 1 year mortality in older hospitalized patients.

    Science.gov (United States)

    Joosten, Etienne; Detroyer, Elke; Milisen, Koen

    2016-08-19

    Anaemia is a common problem in hospitalized older patients and is recognized as a risk factor for a significant number of adverse outcomes. Data of the effect of anaemia on functional status during hospitalization and mortality after discharge are limited. Aim of the study is to examine whether there is an association between anaemia, hand grip strength, gait speed and basic activities of daily living (ADL) during hospitalization and mortality 1 year after discharge in geriatric patients. In a prospective study, data on age, sex, body mass index, Mini-Mental State Examination (MMSE), main clinical diagnosis, number of comorbidities, hand grip strength, gait speed, ADL, haemoglobin, C-reactive protein and estimated Glomerular filtration ratio (eGFR) were recorded in 220 older patients, admitted to the acute geriatric ward of a university hospital. Anaemia was defined as a haemoglobin level anaemia (haemoglobin between 10 and 12 g/dL for women and 10 and 13 g/dL for men). Gait speed (in meters per second) was calculated after a 4.5 m walk and hand grip strength (in kilogram) was assessed with a hydraulic hand dynamometer. Functionality was assessed in the six basic activities of daily living. Information about the vital status was obtained 1 year after discharge with a telephone call. Analysis of covariance (ANCOVA) was used to examine the effect of the anaemia status on the walking speed, hand grip strength and premorbid ADL index and logistic regression analysis was used to examine whether anaemia could be identified as risk factors for mortality 12 months after discharge. Overall, 106 (48 %) patients had anaemia. Hand-grip strength, gait speed and ADL score were not significantly different between anaemic and non-anaemic hospitalized geriatric patients. After adjustment for age, sex, body mass index, eGFR, MMSE, number of comorbidities and main clinical diagnosis, the means for hand-grip strength were 17.3, 19.9 and 19.1 kg (p = 0.38); for gait speed 0

  1. Hydraulic Yaw System

    DEFF Research Database (Denmark)

    Stubkier, Søren; Pedersen, Henrik C.; Mørkholt, M.

    As wind turbines increase in size, combined with increased lifetime demands, new methods for load reduction needs to be examined. One method is to make the yaw system of the turbine soft/flexible and hereby dampen the loads to the system, which is the focus of the current paper. By utilizing...... the HAWC2 aeroelastic code and an extended model of the NREL 5MW turbine combined with a simplified linear model of the turbine, the parameters of the soft yaw system are optimized to reduce loading in critical components. Results shows that a significant reduction in fatigue and extreme loads to the yaw...... system and rotor shaft when utilizing the soft yaw drive concept compared to the original stiff yaw system. The physical demands of the hydraulic yaw system are furthermore examined for a life time of 20 years. Based on the extrapolated loads, the duty cycles show that it is possible to construct...

  2. Electro Hydraulic Hitch Control

    DEFF Research Database (Denmark)

    Hansen, M. R.; Andersen, T. O.; Nielsen, B.

    2003-01-01

    system for agricultural applications and driving for transportation. During tranport phases, the lack of suspension causes the vehicle to bounce and pitch, and makes it difficalt to control. Many systems have been proposed to cope with the oscillatory behavior, and different solutions exist. Common......This paper present and discusses R&D results on electro hydraulic hitch control for off-road vehicle, in particular active damping of oscillation occuring on tractors. The research deals with analysis and control of the oscillations occuring on tractors which are design without any susspection...... for most of the systems are that they operate on the hydrailc actuators generally providing the motive forces for moving the implement and/or attachment, typically a plough. The basic idea and physical working principle are to use the implement, moveable relative to the vehicle, as a damper mass. The paper...

  3. Hand Dominance and Common Hand Conditions.

    Science.gov (United States)

    Lutsky, Kevin; Kim, Nayoung; Medina, Juana; Maltenfort, Mitchell; Beredjiklian, Pedro K

    2016-05-01

    The goals of this study were to (1) assess how frequently patients present for evaluation of common hand disorders in relation to hand dominance and (2) evaluate the effect of hand dominance on function in patients with these conditions. The authors hypothesized that (1) the majority of patients who seek evaluation would have a condition that affects the dominant hand, and (2) disability scores would be worse if the dominant hand is involved. They retrospectively reviewed the records of consecutive patients who presented for treatment to their institution with unilateral symptoms of 5 common disorders of the hand: carpal tunnel syndrome (CTS), de Quervain's tenosynovitis (DEQ), lateral epicondylitis (LE), hand osteoarthritis (OA), and trigger finger (TF). The authors assessed the effect of diagnosis and hand dominance on Disabilities of the Arm, Shoulder and Hand (DASH) scores. The study group comprised 1029 patients (379 men and 650 women) with a mean age of 59.5 years. Ninety percent were right-hand dominant. The dominant and nondominant hands were affected with relatively equal frequency for CTS, DEQ, OA, and TF (range, 45%-53%). Patients with LE had a significantly higher incidence of dominant hand involvement. Men had lower DASH scores than women by an average of 7.9 points, and DASH scores were significantly but slightly higher for the overall group (3.2 points) when the dominant side was affected. Men with LE and women with TF and OA had significantly higher DASH scores when their dominant extremity was affected. Common hand disorders such as CTS, DEQ, OA, and TF affect the dominant and nondominant hands in roughly equivalent proportions, whereas LE is more common on the dominant side. Dominant hand involvement results in significantly worse DASH scores, although the magnitude of this is relatively small. Women have significantly higher DASH scores than men for the conditions evaluated. [Orthopedics. 2016; 39(3):e444-e448.].

  4. Phenomenon of methane driven caused by hydraulic fracturing in methane-bearing coal seams

    Institute of Scientific and Technical Information of China (English)

    Huang Bingxiang; Cheng Qingying; Chen Shuliang

    2016-01-01

    The methane concentration of the return current will always be enhanced to a certain degree when hydraulic fracturing with bedding drilling is implemented to a gassy coal seam in an underground coal mine. The methane in coal seam is driven out by hydraulic fracturing. Thus, the phenomenon is named as methane driven effect of hydraulic fracturing. After deep-hole hydraulic fracturing at the tunneling face of the gassy coal seam, the coal methane content exhibits a‘low-high-low”distribution along exca-vation direction in the following advancing process, verifying the existence of methane driven caused by hydraulic fracturing in methane-bearing coal seam. Hydraulic fracturing causes the change of pore-water and methane pressure in surrounding coal. The uneven distribution of the pore pressure forms a pore pressure gradient. The free methane migrates from the position of high pore (methane) pressure to the position of low pore (methane) pressure. The methane pressure gradient is the fundamental driving force for methane-driven coal seam hydraulic fracturing. The uneven hydraulic crack propagation and the effect of time (as some processes need time to complete and are not completed instantaneously) will result in uneven methane driven. Therefore, an even hydraulic fracturing technique should be used to avoid the negative effects of methane driven; on the other hand, by taking fully advantage of methane driven, two technologies are presented.

  5. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... children, parents, and public health professionals. More > Hand Hygiene Saves Lives (5:10) Recommend on Facebook Tweet Share Compartir Hand Hygiene Saves Lives Hand Hygiene Saves Lives Transcript [28 KB, 2 pages] High ...

  6. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... including, children, parents, and public health professionals. More > Hand Hygiene Saves Lives (5:10) Recommend on Facebook Tweet Share Compartir Hand Hygiene Saves Lives Hand Hygiene Saves Lives Transcript [28 KB, 2 pages] High ...

  7. Hand Hygiene Saves Lives

    Science.gov (United States)

    ... including, children, parents, and public health professionals. More > Hand Hygiene Saves Lives (5:10) Recommend on Facebook Tweet Share Compartir Hand Hygiene Saves Lives Hand Hygiene Saves Lives Transcript [28 KB, 2 pages] High ...

  8. Guideline Implementation: Hand Hygiene.

    Science.gov (United States)

    Goldberg, Judith L

    2017-02-01

    Performing proper hand hygiene and surgical hand antisepsis is essential to reducing the rates of health care-associated infections, including surgical site infections. The updated AORN "Guideline for hand hygiene" provides guidance on hand hygiene and surgical hand antisepsis, the wearing of fingernail polish and artificial nails, proper skin care to prevent dermatitis, the wearing of jewelry, hand hygiene product selection, and quality assurance and performance improvement considerations. This article focuses on key points of the guideline to help perioperative personnel make informed decisions about hand hygiene and surgical hand antisepsis. The key points address the necessity of keeping fingernails and skin healthy, not wearing jewelry on the hands or wrists in the perioperative area, properly performing hand hygiene and surgical hand antisepsis, and involving patients and visitors in hand hygiene initiatives. Perioperative RNs should review the complete guideline for additional information and for guidance when writing and updating policies and procedures.

  9. Hydraulic conductivity of compacted zeolites.

    Science.gov (United States)

    Oren, A Hakan; Ozdamar, Tuğçe

    2013-06-01

    Hydraulic conductivities of compacted zeolites were investigated as a function of compaction water content and zeolite particle size. Initially, the compaction characteristics of zeolites were determined. The compaction test results showed that maximum dry unit weight (γ(dmax)) of fine zeolite was greater than that of granular zeolites. The γ(dmax) of compacted zeolites was between 1.01 and 1.17 Mg m(-3) and optimum water content (w(opt)) was between 38% and 53%. Regardless of zeolite particle size, compacted zeolites had low γ(dmax) and high w(opt) when compared with compacted natural soils. Then, hydraulic conductivity tests were run on compacted zeolites. The hydraulic conductivity values were within the range of 2.0 × 10(-3) cm s(-1) to 1.1 × 10(-7) cm s(-1). Hydraulic conductivity of all compacted zeolites decreased almost 50 times as the water content increased. It is noteworthy that hydraulic conductivity of compacted zeolite was strongly dependent on the zeolite particle size. The hydraulic conductivity decreased almost three orders of magnitude up to 39% fine content; then, it remained almost unchanged beyond 39%. Only one report was found in the literature on the hydraulic conductivity of compacted zeolite, which is in agreement with the findings of this study.

  10. Hydraulic Actuators with Autonomous Hydraulic Supply for the Mainline Aircrafts

    Directory of Open Access Journals (Sweden)

    I. S. Shumilov

    2014-01-01

    Full Text Available Applied in the aircraft control systems, hydraulic servo actuators with autonomous hydraulic supply, so-called, hydraulic actuators of integrated configuration, i.e. combination of a source of hydraulic power and its load in the single unit, are aimed at increasing control system reliability both owing to elimination of the pipelines connecting the actuator to the hydraulic supply source, and owing to avoidance of influence of other loads failure on the actuator operability. Their purpose is also to raise control system survivability by eliminating the long pipeline communications and their replacing for the electro-conductive power supply system, thus reducing the vulnerability of systems. The main reason for a delayed application of the hydraulic actuators in the cutting-edge aircrafts was that such aircrafts require hydraulic actuators of considerably higher power with considerable heat releases, which caused an unacceptable overheat of the hydraulic actuators. Positive and negative sides of the hydraulic actuators, their alternative options of increased reliability and survivability, local hydraulic systems as an advanced alternative to independent hydraulic actuators are considered.Now to use hydraulic actuators in mainline aircrafts is inexpedient since there are the unfairly large number of the problems reducing, first and last, safety of flights, with no essential weight and operational advantages. Still works to create competitive hydraulic actuators ought to be continued.Application of local hydraulic systems (LHS will allow us to reduce length of pressure head and drain pipelines and mass of pipelines, as well as to raise their general fail-safety and survivability. Application of the LHS principle will allow us to use a majority of steering drive advantages. It is necessary to allocate especially the following:- ease of meeting requirements for the non-local spread of the engine weight;- essentially reducing length and weight of

  11. Hydraulic conductivity of organomodified soil

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, R.B.; Grant, J.M.; Voice, T.C.; Rakhshandehroo, G.; Xu, S.; Boyd, S.A. [Michigan State Univ., East Lansing, MI (United States)

    1995-11-01

    The effects of organomodification on soil hydraulic conductivity were investigated. Hydraulic conductivity and porosity of treated and untreated samples of a sandy loam were measured as a function of effective stress. Batch treatment with hexadecyltrimethyl ammonium (HDTMA) and dry packing produced organomodified samples that were 79% less conducive than untreated samples prior to loading. Treated samples lost less hydraulic conductivity as a result of loading than untreated samples so that treated samples had higher conductivity at high loads. Observed differences in conductivity are explained in terms of the role of the treated and untreated clay in controlling initial effective pore size and its change during consolidation.

  12. A Modernized UDM-600 Dynamometer-Based Setup for the Cutting Force Measurement

    Directory of Open Access Journals (Sweden)

    Ya. I. Shuliak

    2016-01-01

    Full Text Available The article considers development of a modernized UDM-600 dynamometer-based setup for measuring the cutting force components. Modernization of existing equipment to improve the method of recording the cutting force components in the automated mode is of relevance. The measuring setup allows recording the cutting force components in turning and milling, as well as the axial force and the torque in the drilling and milling operations.The article presents a block diagram and a schematic diagram of the setup to measure the cutting force components, and describes a basic principle of measuring units within the modernized setup. The developed setup uses a half-bridge strain gauge measuring circuit to record the cutting forces. To enhance the measuring circuit output voltage is used a 16-channel amplifier of LA-UN16 model with a discretely adjustable gain. To record and process electrical signals is used a data acquisition device of NI USB-6009 model, which enables transmitting the received data to a PC via USB-interface. The data acquisition device has a built-in stabilized DC power supply that is used to power the strain gauge bridges. A developed schematic diagram of the measuring setup allows us to realize this measuring device and implement its modernization.Final processing of recorded data is provided through the software developed in visual programming environment LabVIEW 9.0. The program allows us to show the real-time measuring values of the cutting force components graphically and to record the taken data to a text file.The measuring setup modernization enabled increasing measurement accuracy and reducing time for processing and analysis of experimental data obtained when measuring the cutting force components. The MT2 Department of BMSTU uses it in education and research activities and in experimental efforts and laboratory classes.

  13. The Reliability of Strength Tests Performed In Elevated Shoulder Positions Using a Handheld Dynamometer.

    Science.gov (United States)

    McLaine, Sally J; Ginn, Karen A; Kitic, Cecilia M; Fell, James W; Bird, Marie-Louise

    2016-06-06

    The reliable measurement of shoulder strength is important when assessing athletes involved in overhead activities. Swimmers' shoulders are subject to repetitive humeral elevation and consequently have a high risk of developing movement-control issues and pain. Shoulder-strength tests performed in positions of elevation assist with the detection of strength deficits that may affect injury and performance. The reliability of isometric strength tests performed in positions of humeral elevation without manual stabilization, which is a typical clinical scenario, has not been established. To establish the relative and absolute intrarater reliability of shoulder-strength tests functional to swimming in 3 body positions commonly used in the clinical setting. Repeated-measures reliability study. Research laboratory. 15 university students and staff (mean ± SD age 24 ± 8.2 y). Isometric shoulder-strength tests were performed in positions of humeral elevation (flexion and extension in 140° abduction in the scapular plane, internal and external rotation in 90° abduction) on subjects without shoulder pain in supine, prone, and sitting. Subjects were tested by 1 examiner with a handheld dynamometer and retested after 48 h. Relative reliability (ICC3,1) values with 95% CI. Absolute reliability was reported by minimal detectable change (MDC). Good to excellent intrarater reliability was found for all shoulder-strength tests (ICC .87-.99). Intrarater reliability was not affected by body position. MDC% was rotation strength tests performed in humeral elevation demonstrated excellent to good intrarater reliability regardless of body position. A strength change of more than 15% in any position can be considered meaningful.

  14. 燃气轮机性能试验用的康氏水力测功器%Kahn Hydraulic Dynamometers for Performance Testing of Gas Turbines

    Institute of Scientific and Technical Information of China (English)

    盖尔哈特·默克尔; 张国芳

    2005-01-01

    一个多世纪以来,水力测功器一直是测量和诊断发动机性能的重要设备。由于较诸电力与气动机械具有若干固有优点(如单位造价较低,尺寸紧凑,惯性小,快速瞬态响应以及在高转速和大功率工况下的运行能力),水力测功器已经成为航空及工业用和船用燃气轮机发动机进行研制、耐久性、生产性试验和维修后试验用的一致公认的标准手段。电子式快速响应涡轮控制系统的应用更是加快了这一趋势,因为这对动态试验程序提出了更高要求。

  15. HYDRAULICS, ATHENS COUNTY, OHIO, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulic data include spatial datasets and data tables necessary for documenting the hydrologic procedures for estimating flood discharges for a flood insurance...

  16. HYDRAULICS, JACKSON COUNTY, KENTUCKY, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulic data include spatial datasets and data tables necessary for documenting the hydrologic procedures for estimating flood discharges for a flood insurance...

  17. HYDRAULICS, MADISON COUNTY, ALABAMA, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — This Hydraulic data was reviewed and approved by FEMA during the initial MT-2 processing. Recent developments in digital terrain and geospatial database management...

  18. HYDRAULICS, HAMPDEN COUNTY, MA, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulic data in this submittal include spatial datasets and model outputs necessary for computation of the 1-percent flooding extent. The minimum requirement for...

  19. Hydraulic wind energy conversion system

    Energy Technology Data Exchange (ETDEWEB)

    1981-07-01

    The purpose of this research was to design, build and test a hydraulic wind energy system. This design used a three bladed turbine, which drove a hydraulic pump. The energy is transmitted from the pump through a long hose and into a hydraulic motor, where the energy is used. This wind system was built and tested during the winter of 1980-1981. The power train included a five meter, three bladed wind turbine, a 9.8:1 ratio gearbox, a 1.44 cubic inch displacement pump with a small supercharge gear pump attached. The hydraulic fluid was pumped through a 70', 3/4'' I-D-high pressure flexhose, then through a volume control valve and into a 1.44 cubic inch displacement motor. The fluid was returned through a 70', 1'' I-D-flexhose.

  20. 14 CFR 29.1435 - Hydraulic systems.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hydraulic systems. 29.1435 Section 29.1435... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Equipment Miscellaneous Equipment § 29.1435 Hydraulic systems. (a) Design. Each hydraulic system must be designed as follows: (1) Each element of the hydraulic system...

  1. 14 CFR 23.1435 - Hydraulic systems.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hydraulic systems. 23.1435 Section 23.1435... § 23.1435 Hydraulic systems. (a) Design. Each hydraulic system must be designed as follows: (1) Each hydraulic system and its elements must withstand, without yielding, the structural loads expected...

  2. 46 CFR 28.405 - Hydraulic equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Hydraulic equipment. 28.405 Section 28.405 Shipping... Operate With More Than 16 Individuals on Board § 28.405 Hydraulic equipment. (a) Each hydraulic system... than four times the system maximum operating pressure. (c) Each hydraulic system must be equipped...

  3. Advanced Performance Hydraulic Wind Energy

    Science.gov (United States)

    Jones, Jack A.; Bruce, Allan; Lam, Adrienne S.

    2013-01-01

    The Jet Propulsion Laboratory, California Institute of Technology, has developed a novel advanced hydraulic wind energy design, which has up to 23% performance improvement over conventional wind turbine and conventional hydraulic wind energy systems with 5 m/sec winds. It also has significant cost advantages with levelized costs equal to coal (after carbon tax rebate). The design is equally applicable to tidal energy systems and has passed preliminary laboratory proof-of-performance tests, as funded by the Department of Energy.

  4. Technologies and Innovations for Hydraulic Pumps

    OpenAIRE

    Ivantysynova, Monika

    2016-01-01

    Positive displacement machines working as hydraulic pumps or hydraulic motors have always been, are and will be an essential part of any hydraulic system. Current trends and future demands on energy efficient systems will not only drastically increase the number of positive displacement machines needed for modern efficient hydraulic circuits but will significantly change the performance requirements of pumps and motors. Throttleless system configurations will change the landscape of hydraulic...

  5. A ground-based comparison of the Muscle Atrophy Research and Exercise System (MARES) and a commercially available isokinetic dynamometer

    Science.gov (United States)

    English, Kirk L.; Hackney, Kyle J.; De Witt, John K.; Ploutz-Snyder, Robert J.; Goetchius, Elizabeth L.; Ploutz-Snyder, Lori L.

    2013-11-01

    IntroductionInternational Space Station (ISS) crewmembers perform muscle strength and endurance testing pre- and postflight to assess the physiologic adaptations associated with long-duration exposure to microgravity. However, a reliable and standardized method to document strength changes in-flight has not been established. To address this issue, a proprietary dynamometer, the Muscle Atrophy Research and Exercise System (MARES) has been developed and flown aboard the ISS. The aims of this ground-based investigation were to: (1) evaluate the test-retest reliability of MARES and (2) determine its agreement with a commercially available isokinetic dynamometer previously used for pre- and postflight medical testing. MethodsSix males (179.5±4.7 cm; 82.0±8.7 kg; 31.3±4.0 yr) and four females (163.2±7.3 cm; 63.2±1.9 kg; 32.3±6.8 yr) completed two testing sessions on a HUMAC NORM isokinetic dynamometer (NORM) and two sessions on MARES using a randomized, counterbalanced, cross-over design. Peak torque values at 60° and 180° s-1 were calculated from five maximal repetitions of knee extension (KE) and knee flexion (KF) for each session. Total work at 180° s-1 was determined from the area under the torque versus displacement curve during 20 maximal repetitions of KE and KF. ResultsIntraclass correlation coefficients were relatively high for both devices (0.90-0.99). Only one dependent measure, KE peak torque at 60° s-1 exhibited good concordance between devices (ρ=0.92) and a small average difference (0.9±17.3 N m). ConclusionMARES demonstrated acceptable test-retest reliability and thus should serve as a good tool to monitor in-flight strength changes. However, due to poor agreement with NORM, it is not advisable to compare absolute values obtained on these devices.

  6. In-Use and Vehicle Dynamometer Evaluation and Comparison of Class 7 Hybrid Electric and Conventional Diesel Delivery Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Burton, J.; Walkowicz, K.; Sindler, P.; Duran, A.

    2013-10-01

    This study compared fuel economy and emissions between heavy-duty hybrid electric vehicles (HEVs) and equivalent conventional diesel vehicles. In-use field data were collected from daily fleet operations carried out at a FedEx facility in California on six HEV and six conventional 2010 Freightliner M2-106 straight box trucks. Field data collection primarily focused on route assessment and vehicle fuel consumption over a six-month period. Chassis dynamometer testing was also carried out on one conventional vehicle and one HEV to determine differences in fuel consumption and emissions. Route data from the field study was analyzed to determine the selection of dynamometer test cycles. From this analysis, the New York Composite (NYComp), Hybrid Truck Users Forum Class 6 (HTUF 6), and California Air Resource Board (CARB) Heavy Heavy-Duty Diesel Truck (HHDDT) drive cycles were chosen. The HEV showed 31% better fuel economy on the NYComp cycle, 25% better on the HTUF 6 cycle and 4% worse on the CARB HHDDT cycle when compared to the conventional vehicle. The in-use field data indicates that the HEVs had around 16% better fuel economy than the conventional vehicles. Dynamometer testing also showed that the HEV generally emitted higher levels of nitric oxides than the conventional vehicle over the drive cycles, up to 77% higher on the NYComp cycle (though this may at least in part be attributed to the different engine certification levels in the vehicles tested). The conventional vehicle was found to accelerate up to freeway speeds over ten seconds faster than the HEV.

  7. Can a wearable strain sensor based on a carbon nanotube network be an alternative to an isokinetic dynamometer for the measurement of knee-extensor muscle strength?

    Science.gov (United States)

    Benlikaya, Ruhan; Ege, Yavuz; Pündük, Zekine; Slobodian, Petr; Meriç, Gökhan

    2017-04-01

    This study aimed to find out whether a wearable strain sensor including thermoplastic polyurethane composite with a multi-walled carbon nanotube network could be a viable alternative to an isokinetic dynamometer for the measurement of knee-extensor muscle strength. For the first time, the voltage-torque and angle–time relations of the sensor were determined to allow a comparison between the angle-dependent torque changes of the dynamometer and the sensor. This comparison suggested that the torque–angle relations of the dynamometer and the sensor did not have the same characteristics. In this regard, the sensor may be used in the torque measurements due to the moderate correlation between the torque values determined via the isokinetic dynamometer and the sensor and due to the significant difference between low and high torque values of the sensor. By the same token, the torque-angle graph of the sensor may be more informative than that of the dynamometer in evaluation of knee problems.

  8. Comparison of pressure pain threshold, grip strength,dexterity and touch pressure of dominant and non-dominant hands within and between right-and left-handed subjects.

    Science.gov (United States)

    Ozcan, Ayse; Tulum, Zeliha; Pinar, Lamia; Başkurt, Ferdi

    2004-12-01

    This study was done to evaluate differences in pressure pain threshold, grip strength, manual dexterity and touch pressure threshold in the dominant and non-dominant hands of right- and left-handed subjects, and to compare findings within and between these groups. Thirty-nine right-handed and twenty-one left-handed subjects participated in the study. Pressure pain threshold was assessed using a dolorimeter, grip strength was assessed with a hand-grip dynamometer, manual dexterity was evaluated using the VALPAR Component Work Sample-4 system, and touch pressure threshold was determined using Semmes Weinstein monofilaments. Results for the dominant and non-dominant hands were compared within and between the groups. In the right-handed subjects, the dominant hand was significantly faster with the VALPAR Component Work Sample-4, showed significantly greater grip strength, and had a significantly higher pressure pain threshold than the non-dominant hand. The corresponding results for the two hands were similar in the left-handed subjects. The study revealed asymmetrical manual performance in grip strength, manual dexterity and pressure pain threshold in right-handed subjects, but no such asymmetries in left-handed subjects.

  9. Earthquakes Induced by Hydraulic Fracturing in Poland Township, Ohio

    Science.gov (United States)

    Skoumal, R.; Brudzinski, M. R.; Currie, B. S.

    2014-12-01

    Felt seismicity induced by hydraulic fracturing is very rare with only a handful of reported cases worldwide. Using an optimized multi-station cross-correlation template matching routine, 77 earthquakes were identified in Poland Township, Mahoning County, Ohio that were closely related spatially and temporally to active hydraulic fracturing operations. We identified earthquakes as small as M ~1 up to M 3, one of the largest earthquakes induced by hydraulic fracturing in the United States. These events all occurred 4-12 March 2014 and the rate decayed once the Ohio Department of Natural Resources issued a shutdown of hydraulic fracturing at a nearby well on 10 March. Using a locally derived velocity model and double difference relocation, the earthquake epicenters occurred during six stimulation stages along two horizontal well legs that were located ~0.8 km away. Nearly 100 stages in nearby wells at greater distances from the earthquake source region did not coincide with detected seismicity. During the sequence, hypocenters migrated ~600 m along an azimuth of 083 degrees defining a vertically oriented plane of seismicity close to the top of the Precambrian basement. The focal mechanism determined for the M 3 event had a vertically oriented left-lateral fault plane consistent with the earthquake distribution and the regional stress field. The focal mechanism, orientation, and depth of hypocenters were similar to that of the 2011 Youngstown earthquake sequence that occurred ~20 km away, but was correlated with wastewater injection instead of hydraulic fracturing. Considering the relatively large magnitude of these events and the b-value of 0.85, it appears the hydraulic fracturing induced slip along a pre-existing fault/fracture zone optimally oriented in the regional stress field.

  10. Torque Production Using Hand Cranks in a Simulated Gear-Operated Valve Opening Task.

    Science.gov (United States)

    Schulze, Lawrence J H; Stanton, Edward; Patel, Anupam; Cheli, Maurizio

    1997-01-01

    Hand cranks are used in a variety of industries to actuate valves and in other gear-operated applications. In order to evaluate these types of operations and their compatibility with operator strength capabilities, a rotational dynamometer was used to measure torque production capability of operators using a hand crank at different heights and angles (with respect to the coronal plane). The tests were conducted for both clockwise and counterclockwise rotations using the dominant arm of each test participant. A total of 18 tests were completed by each of five male right-handed test participants. A 0° declination angle, counterclockwise operation, and both 40.65 cm and 60.96 cm heights were found to be associated with the greatest torque production capabilities.

  11. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... public health professionals. More > Hand Hygiene Saves Lives (5:10) Recommend on Facebook Tweet Share Compartir Hand ... High resolution [22.9 MB] Open Captioned [14.5 MB] Request a higher resolution file Copy the ...

  12. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... future Salt Matters: Preserving Choice, Protecting Health More Information Hand Hygiene Clean Hands Basics Send Us Feedback ... 2013 Page last updated: November 22, 2013 Content source: Centers for Disease Control and Prevention Page maintained ...

  13. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... 22.9 MB] Open Captioned [14.5 MB] Request a higher resolution file Copy the code below ... future Salt Matters: Preserving Choice, Protecting Health More Information Hand Hygiene Clean Hands Basics Send Us Feedback ...

  14. Arthritis of the Hand

    Science.gov (United States)

    .org Arthritis of the Hand Page ( 1 ) The hand and wrist have multiple small joints that work together to ... a shoelace. When the joints are affected by arthritis, activities of daily living can be difficult. Arthritis ...

  15. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... Tricky Treats Hygiene Fight Germs. Wash Your Hands! Go with the Flow Hand Hygiene Saves Lives Wash ... Wes Studi: Signs (:30) Traveler’s Health Way to Go Way to Go: Many Healthy Returns (4:00) ...

  16. Complex Fluids and Hydraulic Fracturing.

    Science.gov (United States)

    Barbati, Alexander C; Desroches, Jean; Robisson, Agathe; McKinley, Gareth H

    2016-06-07

    Nearly 70 years old, hydraulic fracturing is a core technique for stimulating hydrocarbon production in a majority of oil and gas reservoirs. Complex fluids are implemented in nearly every step of the fracturing process, most significantly to generate and sustain fractures and transport and distribute proppant particles during and following fluid injection. An extremely wide range of complex fluids are used: naturally occurring polysaccharide and synthetic polymer solutions, aqueous physical and chemical gels, organic gels, micellar surfactant solutions, emulsions, and foams. These fluids are loaded over a wide range of concentrations with particles of varying sizes and aspect ratios and are subjected to extreme mechanical and environmental conditions. We describe the settings of hydraulic fracturing (framed by geology), fracturing mechanics and physics, and the critical role that non-Newtonian fluid dynamics and complex fluids play in the hydraulic fracturing process.

  17. Hydraulic properties of ladle slags

    Directory of Open Access Journals (Sweden)

    J. Vlček

    2016-07-01

    Full Text Available The article presents results of examining of hydraulic properties of ladle slags formed during production of steel. The studied ladle slags were subjected to different cooling mode from the molten state. Based on the ability of the slag react with the water was assessed their hydraulic activity. The hydraulic properties are caused by the presence of minerals dicalcium silicate, tricalcium aluminate, mayenite, brownmillerite and dicalcium ferite. The emergence of required hydrating phases in the ladle slags is conditioned by a sufficient CaO content and their cooling rate. The contact the slag with water during processing and their ageing has a negative effect. The experiment has shown that the phase transformation of the mineral dicalcium silicate which occurs during cooling of the ladle slags cause their volume instability.

  18. Hydraulic resistance of biofilms

    KAUST Repository

    Dreszer, C.

    2013-02-01

    Biofilms may interfere with membrane performance in at least three ways: (i) increase of the transmembrane pressure drop, (ii) increase of feed channel (feed-concentrate) pressure drop, and (iii) increase of transmembrane passage. Given the relevance of biofouling, it is surprising how few data exist about the hydraulic resistance of biofilms that may affect the transmembrane pressure drop and membrane passage. In this study, biofilms were generated in a lab scale cross flow microfiltration system at two fluxes (20 and 100Lm-2h-1) and constant cross flow (0.1ms-1). As a nutrient source, acetate was added (1.0mgL-1 acetate C) besides a control without nutrient supply. A microfiltration (MF) membrane was chosen because the MF membrane resistance is very low compared to the expected biofilm resistance and, thus, biofilm resistance can be determined accurately. Transmembrane pressure drop was monitored. As biofilm parameters, thickness, total cell number, TOC, and extracellular polymeric substances (EPS) were determined, it was demonstrated that no internal membrane fouling occurred and that the fouling layer actually consisted of a grown biofilm and was not a filter cake of accumulated bacterial cells. At 20Lm-2h-1 flux with a nutrient dosage of 1mgL-1 acetate C, the resistance after 4 days reached a value of 6×1012m-1. At 100Lm-2h-1 flux under the same conditions, the resistance was 5×1013m-1. No correlation of biofilm resistance to biofilm thickness was found; Biofilms with similar thickness could have different resistance depending on the applied flux. The cell number in biofilms was between 4×107 and 5×108 cellscm-2. At this number, bacterial cells make up less than a half percent of the overall biofilm volume and therefore did not hamper the water flow through the biofilm significantly. A flux of 100Lm-2h-1 with nutrient supply caused higher cell numbers, more biomass, and higher biofilm resistance than a flux of 20Lm-2h-1. However, the biofilm thickness

  19. Hands in Systemic Disease

    Science.gov (United States)

    ... Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is a Hand Surgeon? What is ... nerves, skin and skin-related tissues, bones, and ... a systemic diseases. The hands may show changes noticed by the patient or ...

  20. Robotic hand and fingers

    Energy Technology Data Exchange (ETDEWEB)

    Salisbury, Curt Michael; Dullea, Kevin J.

    2017-06-06

    Technologies pertaining to a robotic hand are described herein. The robotic hand includes one or more fingers releasably attached to a robotic hand frame. The fingers can abduct and adduct as well as flex and tense. The fingers are releasably attached to the frame by magnets that allow for the fingers to detach from the frame when excess force is applied to the fingers.

  1. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... Matters: Preserving Choice, Protecting Health (4:30) Salt Matters: Preserving Choice, Protecting Health (2:00) Tricky Treats Hygiene Fight Germs. Wash Your Hands! Go with the Flow Hand Hygiene Saves Lives Wash Your Hands Physical Activity Knees Lifted High Making Health Easier: Active ...

  2. Controls of Hydraulic Wind Turbine

    Directory of Open Access Journals (Sweden)

    Zhang Yin

    2016-01-01

    Full Text Available In this paper a hydraulic wind turbine generator system was proposed based on analysis the current wind turbines technologies. The construction and principles were introduced. The mathematical model was verified using MATLAB and AMsim. A displacement closed loop of swash plate of motor and a speed closed loop of generator were setup, a PID control is introduced to maintain a constant speed and fixed frequency at wind turbine generator. Simulation and experiment demonstrated that the system can connect grid to generate electric and enhance reliability. The control system demonstrates a high performance speed regulation and effectiveness. The results are great significant to design a new type hydraulic wind turbine system.

  3. Integrating hydraulic equivalent sections into a hydraulic geometry study

    Science.gov (United States)

    Jia, Yanhong; Yi, Yujun; Li, Zhiwei; Wang, Zhaoyin; Zheng, Xiangmin

    2017-09-01

    Hydraulic geometry (HG) is an important geomorphic concept that has played an indispensable role in hydrological analyses, physical studies of streams, ecosystem and aquatic habitat studies, and sedimentology research. More than 60 years after Leopold and Maddock (1953) first introduced the concept of HG, researchers have still not uncovered the physical principles underlying HG behavior. One impediment is the complexity of the natural river cross section. The current study presents a new way to simplify the cross section, namely, the hydraulic equivalent section, which is generalized from the cross section in the ;gradually varied flow of an alluvial river; (GVFAR) and features hydrodynamic properties and bed-building laws similar to those of the GVFAR. Energy balance was used to derive the stage Z-discharge Q relationship in the GVFAR. The GVFAR in the Songhua River and the Yangtze River were selected as examples. The data, including measured discharge, river width, water stage, water depth, wet area, and cross section, were collected from the hydrological yearbooks of typical hydrological stations on the Songhua River and the Yangtze River from 1955 to 1987. The relationships between stage Z-discharge Q and cross-sectional area A-stage Z at various stations were analyzed, and ;at-a-station hydraulic geometry; (AHG) relationships were obtained in power-law forms. Based on derived results and observational data analysis, the Z-Q and Z-A relationships of AHG were similar to rectangular weir flows, thus the cross section of the GVFAR was generalized as a compound rectangular, hydraulic equivalent cross section. As to bed-building characteristics, the bankfull discharge method and the stage-discharge-relation method were used to calculate the dominant variables of the alluvial river. This hydraulic equivalent section has the same Z-Q relation, Z-A relation, dominant discharge, dominant river width, and dominant water depth as the cross section in the GVFAR. With the

  4. The use of kinesiology taping method in patients with rheumatoid hand--pilot study.

    Science.gov (United States)

    Szczegielniak, Jan; Łuniewski, Jacek; Bogacz, Katarzyna; Sliwiński, Zbigniew

    2012-01-01

    Rheumatoid arthritis (RA) most frequently affects smaller joints in the hands and feet. Among the most common deformations resulting from the progression of the disease are ulnar deviation, Boutonniere deformity, swan neck deformity, contractures and limited range of movement in the hand and wrist joints, muscular atrophy of long and short muscles. The topic of this article is the influence of using Kinesiology Taping method on the functioning of the hand of the patient suffering from rheumatoid arthritis. The research involved 20 patients suffering from rheumatoid arthritis (16 women, 4 men), treated in the Hospital in Kup. Average age of patients was 62.2. Research subjects, apart from pharmacological treatment in the hospital ward, received standard physiotherapy. In case of 10 patients additional K-Active Tape applications were used to correct ulnar positioning of the hand and improve hand functioning. Prior to physiotherapy, all patients were given a hand functioning test and a dynamometer measurement was made. The tests were repeated after the 2-week rehabilitation process has been completed. The results were subjected to statistical analysis with the use of the Wilcoxon test and the U Mann-Whitney test. The assessment of the correlation between analysed parameters was made with the use of linear correlation test. In the group where Kinesiology Tape applications were used, hand muscle strength increased significantly (p0.8). Results suggest Kinesiology Taping method useful for physiotherapy of rheumatoid hand.

  5. CRITICALITY CURVES FOR PLUTONIUM HYDRAULIC FLUID MIXTURES

    Energy Technology Data Exchange (ETDEWEB)

    WITTEKIND WD

    2007-10-03

    This Calculation Note performs and documents MCNP criticality calculations for plutonium (100% {sup 239}Pu) hydraulic fluid mixtures. Spherical geometry was used for these generalized criticality safety calculations and three geometries of neutron reflection are: {sm_bullet}bare, {sm_bullet}1 inch of hydraulic fluid, or {sm_bullet}12 inches of hydraulic fluid. This document shows the critical volume and critical mass for various concentrations of plutonium in hydraulic fluid. Between 1 and 2 gallons of hydraulic fluid were discovered in the bottom of HA-23S. This HA-23S hydraulic fluid was reported by engineering to be Fyrquel 220. The hydraulic fluid in GLovebox HA-23S is Fyrquel 220 which contains phosphorus. Critical spherical geometry in air is calculated with 0 in., 1 in., or 12 inches hydraulic fluid reflection.

  6. DCS Hydraulics Submittal, Butler County, Alabama, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulics data includes spatial datasets and data tables necessary for documenting the hydraulic procedures for computing flood elevations for a flood insurance...

  7. DCS Hydraulics Submittal, Bullock County, Alabama, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulics data includes spatial datasets and data tables necessary for documenting the hydraulic procedures for computing flood elevations for a flood insurance...

  8. DCS Hydraulics Submittal, Covington County, Alabama, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulics data includes spatial datasets and data tables necessary for documenting the hydraulic procedures for computing flood elevations for a flood insurance...

  9. High Pressure Hydraulic Distribution System

    Science.gov (United States)

    1991-05-20

    to 500 0 F. 5 cycles. 5000 F room temperature to 50001F; 45 ______________ Icycles The tesis planned for the distribution system demonstrator were...American Society for Testing and Materials ASTM D412 - Tension Testing of Vulcanized Rubber ASTM D571 - Testing Automotive Hydraulic Brake Hose Society of

  10. Hydraulic fracturing system and method

    Energy Technology Data Exchange (ETDEWEB)

    Ciezobka, Jordan; Salehi, Iraj

    2017-02-28

    A hydraulic fracturing system and method for enhancing effective permeability of earth formations to increase hydrocarbon production, enhance operation efficiency by reducing fluid entry friction due to tortuosity and perforation, and to open perforations that are either unopened or not effective using traditional techniques, by varying a pump rate and/or a flow rate to a wellbore.

  11. Hydraulic jumps in a channel

    DEFF Research Database (Denmark)

    Bonn, D.; Andersen, Anders Peter; Bohr, Tomas

    2009-01-01

    We present a study of hydraulic jumps with flow predominantly in one direction, created either by confining the flow to a narrow channel with parallel walls or by providing an inflow in the form of a narrow sheet. In the channel flow, we find a linear height profile upstream of the jump as expected...

  12. Hydraulic Fracture Containment in Sand

    NARCIS (Netherlands)

    Dong, Y.

    2010-01-01

    The mechanism of hydraulic fracturing in soft, high permeability material is considered fundamentally different from that in hard, low permeability rock, where a tensile fracture is created and conventional linear elastic fracture mechanics (LEFM) applies. The fracturing and associated modeling work

  13. Design of hydraulic recuperation unit

    Directory of Open Access Journals (Sweden)

    Jandourek Pavel

    2016-01-01

    Full Text Available This article deals with design and measurement of hydraulic recuperation unit. Recuperation unit consist of radial turbine and axial pump, which are coupled on the same shaft. Speed of shaft with impellers are 6000 1/min. For economic reasons, is design of recuperation unit performed using commercially manufactured propellers.

  14. Tree Hydraulics: How Sap Rises

    Science.gov (United States)

    Denny, Mark

    2012-01-01

    Trees transport water from roots to crown--a height that can exceed 100 m. The physics of tree hydraulics can be conveyed with simple fluid dynamics based upon the Hagen-Poiseuille equation and Murray's law. Here the conduit structure is modelled as conical pipes and as branching pipes. The force required to lift sap is generated mostly by…

  15. Tree Hydraulics: How Sap Rises

    Science.gov (United States)

    Denny, Mark

    2012-01-01

    Trees transport water from roots to crown--a height that can exceed 100 m. The physics of tree hydraulics can be conveyed with simple fluid dynamics based upon the Hagen-Poiseuille equation and Murray's law. Here the conduit structure is modelled as conical pipes and as branching pipes. The force required to lift sap is generated mostly by…

  16. Evaluating the reliability of a novel neck-strength assessment protocol for healthy adults using self-generated resistance with a hand-held dynamometer.

    Science.gov (United States)

    Versteegh, Theo; Beaudet, Danielle; Greenbaum, Marla; Hellyer, Leah; Tritton, Amanda; Walton, Dave

    2015-01-01

    Objectif : Évaluer la convergence test-retest intra et intersessionnelle d'un nouveau protocole d'évaluation de la force du cou au moyen d'un dynamomètre portatif. Contexte: Une recension des écrits a révélé un manque de protocoles d'évaluation de la force du cou à la fois portables et fiables. La dynamométrie manuelle est une méthode portable et peu coûteuse d'évaluation de la force musculaire, mais elle n'est pas utilisée couramment pour évaluer la force du cou. Méthodes : On a utilisé un dynamomètre portatif pour évaluer la force du cou chez 30 participants en bonne santé. On a mesuré la force maximale en flexion cervicale, extension, flexion latérale, flexion latérale avec rotation et rotation pure en utilisant la main ipsilatérale pour appliquer une résistance isométrique pendant 3 secondes. On a pris trois mesures en 6 à 8 jours. Résultats : Les coefficients de corrélation intraclasse (CCI) de test-retest ont révélé une grande fiabilité variant de 0,94 à 0,97 dans le cas de toutes les directions vérifiées de l'essai 1 à l'essai 2 (fiabilité intrasessionnelle) [CCI (2,1), absolu]. Les valeurs CCI ont démontré une fiabilité intersessionnelle variant de bonne à élevée, variant de 0,87 à 0,95 dans le cas de toutes les directions mises à l'épreuve de l'essai 1 à l'essai 3 [CCI (2,1), absolu]. Conclusion : Les résultats indiquent qu'il est possible d'appliquer le protocole d'évaluation de la force du cou et du quadrant supérieur par les cinq positions d'essai en utilisant la dynamométrie manuelle, et qu'il produit une fiabilité variant de bonne à élevée.

  17. A new linear type hydraulic motor

    Science.gov (United States)

    Jiang, Dong; Zhang, Tong; Li, Wenhua; Chen, Xinyang

    2017-08-01

    This paper proposes the design of liner type hydraulic motor on the base of inner curved radial piston hydraulic motor. The hydraulic cylinders of the new type motor are in the straight line which will improve the utilization of the axial space and different out power can be supplied by changes the number of cylinders. In this paper, the structure and working principle of the liner type hydraulic motor is introduced.

  18. Hydraulic characterization of " Furcraea andina

    Science.gov (United States)

    Rivera-Velasquez, M. F.; Fallico, C.; Molinari, A.; Santillan, P.; Salazar, M.

    2012-04-01

    The present level of pollution, increasingly involving groundwaters, constitutes a serious risk for environment and human health. Therefore the remediation of saturated and unsaturated soils, removing pollutant materials through innovative and economic bio-remediation techniques is more frequently required. Recent studies on natural fiber development have shown the effectiveness of these fibers for removal of some heavy metals, due to the lignin content in the natural fibers which plays an important role in the adsorption of metal cations (Lee et al., 2004; Troisi et al., 2008; C. Fallico, 2010). In the context of remediation techniques for unsaturated and/or saturated zone, an experimental approach for the hydraulic characterization of the "Furcraea andina" (i.e., Cabuya Blanca) fiber was carried out. This fiber is native to Andean regions and grows easily in wild or cultivated form in the valleys and hillsides of Colombia, Ecuador, and Peru. Fibers of "Furcraea andina" were characterized by experimental tests to determine their hydraulic conductivity or permeability and porosity in order to use this medium for bioremediation of contaminated aquifer exploiting the physical, chemical and microbial capacity of natural fiber in heavy metal adsorption. To evaluate empirically the hydraulic conductivity, laboratory tests were carried out at constant head specifically on the fibers manually extracted. For these tests we used a flow cell (used as permeameter), containing the "Furcraea andina" fibers to be characterized, suitably connected by a tygon pipe to a Marriott's bottle, which had a plastic tube that allow the adjustment of the hydraulic head for different tests to a constant value. By this experiment it was also possible to identify relationships that enable the estimation of permeability as a function of density, i.e. of the compaction degree of the fibers. Our study was carried out for three values of hydraulic head (H), namely 10, 18, and 25 cm and for each

  19. 14 CFR 25.1435 - Hydraulic systems.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hydraulic systems. 25.1435 Section 25.1435... STANDARDS: TRANSPORT CATEGORY AIRPLANES Equipment Miscellaneous Equipment § 25.1435 Hydraulic systems. (a) Element design. Each element of the hydraulic system must be designed to: (1) Withstand the proof...

  20. 14 CFR 27.1435 - Hydraulic systems.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hydraulic systems. 27.1435 Section 27.1435... STANDARDS: NORMAL CATEGORY ROTORCRAFT Equipment Safety Equipment § 27.1435 Hydraulic systems. (a) Design. Each hydraulic system and its elements must withstand, without yielding, any structural loads...

  1. Inter-machine reliability of the Biodex and Cybex isokinetic dynamometers for knee flexor/extensor isometric, concentric and eccentric tests.

    Science.gov (United States)

    de Araujo Ribeiro Alvares, João Breno; Rodrigues, Rodrigo; de Azevedo Franke, Rodrigo; da Silva, Bruna Gonçalves Cordeiro; Pinto, Ronei Silveira; Vaz, Marco Aurélio; Baroni, Bruno Manfredini

    2015-02-01

    To assess the inter-machine reliability of the Biodex System 3 Pro and Cybex Humac Norm Model 770 dynamometers for knee extensor and knee flexor peak torque measurements in isometric, concentric and eccentric tests. Randomized/crossover. Exercise Research Laboratory, Federal University of Rio Grande do Sul (Brazil). 25 healthy male subjects. Isometric, concentric and eccentric knee extensor and knee flexor peak torques recorded in the same test procedure performed on both isokinetic dynamometers. One-way ANOVA, intraclass correlation coefficient (ICC), standard error of measurement (SEM) and coefficient of variation (CV) were used to verify significant differences, relative and absolute reliability between devices. No significant differences were found between tests performed on Biodex and Cybex (p > 0.05). ICC values indicated a high to very high reproducibility for isometric, concentric and eccentric peak torques (0.88-0.92), and moderate to high reliability for agonist-antagonist strength ratios (0.62-0.73). Peak torque did not show great difference between dynamometers for SEM (3.72-11.27 Nm) and CV (5.27-7.77%). Strength ratios presented CV values of 8.57-10.72%. Maximal knee extensor and knee flexor tests performed in isometric (60° of knee flexion), concentric and eccentric modes at 60°/s in Biodex and Cybex dynamometers present similar values. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Hand eczema classification

    DEFF Research Database (Denmark)

    Diepgen, T L; Andersen, Klaus Ejner; Brandao, F M;

    2008-01-01

    Summary Background Hand eczema is a long-lasting disease with a high prevalence in the background population. The disease has severe, negative effects on quality of life and sometimes on social status. Epidemiological studies have identified risk factors for onset and prognosis, but treatment...... of the disease is rarely evidence based, and a classification system for different subdiagnoses of hand eczema is not agreed upon. Randomized controlled trials investigating the treatment of hand eczema are called for. For this, as well as for clinical purposes, a generally accepted classification system...... for hand eczema is needed. Objectives The present study attempts to characterize subdiagnoses of hand eczema with respect to basic demographics, medical history and morphology. Methods Clinical data from 416 patients with hand eczema from 10 European patch test clinics were assessed. Results...

  3. Hand deburring guide

    Energy Technology Data Exchange (ETDEWEB)

    Gillespie, L.K.

    1979-07-01

    Appropriate hand deburring techniques have always been difficult to define because of the infinite variety of part shapes, sizes, materials, and burr conditions. This guide, however, has been prepared to assist those responsible for hand deburring. The purpose of the guide is to define Bendix Kansas City burr specifications and inspection practices; to define the results of practical tests on hand deburring; to define some typical in-house practices; and to define the in-house tools available for this work.

  4. The alien hand syndrome

    Science.gov (United States)

    Panikkath, Deepa; Mojumder, Deb; Nugent, Kenneth

    2014-01-01

    A 77-year-old woman presented with the complaint of observing her left hand moving without her knowledge while watching television. Her left hand stroked her face and hair as if somebody was controlling it. These movements lasted only half an hour but on recovery, she had left hemiparesis. Alien hand syndrome as the presentation of cardioembolic stroke is extremely rare but can be terrifying to patients. PMID:24982566

  5. Hand Hygiene: An Update.

    Science.gov (United States)

    Bolon, Maureen K

    2016-09-01

    The medical field has long recognized the importance of hand hygiene in preventing health care-associated infections, yet studies indicate that this important task is performed only 40% of the time. Health care workers cite several barriers to optimal performance of hand hygiene, but the time required to perform this task is foremost among them. Introduction of alcohol-based hand rubs, bundled interventions, and incorporation of technologies designed to monitor and promote hand hygiene all represent promising advances in this field. Copyright © 2016 Elsevier Inc. All rights reserved.

  6. [Optimizing surgical hand disinfection].

    Science.gov (United States)

    Kampf, G; Kramer, A; Rotter, M; Widmer, A

    2006-08-01

    For more than 110 years hands of surgeons have been treated before a surgical procedure in order to reduce the bacterial density. The kind and duration of treatment, however, has changed significantly over time. Recent scientific evidence suggests a few changes with the aim to optimize both the efficacy and the dermal tolerance. Aim of this article is the presentation and discussion of new insights in surgical hand disinfection. A hand wash should be performed before the first disinfection of a day, ideally at least 10 min before the beginning of the disinfection as it has been shown that a 1 min hand wash significantly increases skin hydration for up to 10 min. The application time may be as short as 1.5 min depending on the type of hand rub. Hands and forearms should be kept wet with the hand rub for the recommended application time in any case. A specific rub-in procedure according to EN 12791 has been found to be suitable in order to avoid untreated skin areas. The alcohol-based hand rub should have a proven excellent dermal tolerance in order to ensure appropriate compliance. Considering these elements in clinical practice can have a significant impact to optimize the high quality of surgical hand disinfection for prevention of surgical site infections.

  7. Thermal Hydraulic Performance of Tight Lattice Bundle

    Science.gov (United States)

    Yamamoto, Yasushi; Akiba, Miyuki; Morooka, Shinichi; Shirakawa, Kenetsu; Abe, Nobuaki

    Recently, the reduced moderation spectrum BWR has been studied. The fast neutron spectrum is obtained through triangular tight lattice fuel. However, there are few thermal hydraulic test data and thermal hydraulic correlation applicable to critical power prediction in such a tight lattice bundle. This study aims to enhance the database of the thermal hydraulic performance of the tight lattice bundle whose rod gap is about 1mm. Therefore, thermal hydraulic performance measurement tests of tight lattice bundles for the critical power, the pressure drop and the counter current flow limiting were performed. Moreover, the correlations to evaluate the thermal-hydraulic performance of the tight lattice bundle were developed.

  8. Design of hydraulic output Stirling engine

    Science.gov (United States)

    Toscano, W. M.; Harvey, A. C.; Lee, K.

    1983-01-01

    A hydraulic output system for the RE-1000 free piston stirling engine (FPSE) was designed. The hydraulic output system can be readily integrated with the existing hot section of RE-1000 FPSE. The system has two simply supported diaphragms which separate the engine gas from the hydraulic fluid, a dynamic balance mechanism, and a novel, null center band hydraulic pump. The diaphragms are designed to endure more than 10 billion cycles, and to withstand the differential pressure load as high as 14 MPa. The projected thermodynamic performance of the hydraulic output version of RE-1000 FPSE is 1.87 kW at 29/7 percent brake efficiency.

  9. [Hand surgery training].

    Science.gov (United States)

    Moutet, F; Haloua, J P

    2003-10-01

    Training of the hand surgeon HAND SURGEON A CONCEPT: The hand surgeon is supposed to be in charge of all the hand lesions regarding, skeleton, muscles, tendons, nerves and vessels. He has to be able to insure reparation and coverage of all of them. So he is involved in all the structures, which insure integrity and function of the hand. PURPOSE AND WAYS OF TRAINING: To obtain the asked ability, the hand surgeon training has to be global and sustained by two underlying surgical specialities: orthopedic surgery and plastic and reconstructive surgery. From 2000 after many years of dealings, a Right to the Title in Hand Surgery was born. This Right to the Title wants to be the formal recognition of the specific training of the hand surgeon. For the well-recognized ancient hand surgeons they need to be confirmed by one's peers. Now a day the hand surgeon has to satisfy to this specific training: Passed the complete training and exam of the Orthopedic or Plastic surgery board. Spent at least 6 months as resident in the other underlying specialty. Passed a microsurgery examination. Passed one of the four national Hand Surgery diplomas (DIU/Inter-Universitary Diploma). The examinations have been harmonized. A common formation is delivered regarding hand surgery, the way of examination is the same and the formation is 2 years long. The final exam is presented in front of board of examiners where a teacher of one of the other three national diplomas is present. Spent at least 2 years in a formative hand surgery unit, listed by the French College of Hand Surgeons, as senior surgeon. Those requirements are heavy to assume and need a heavy personal involvement. That seems to be necessary to have an ability level as high as possible. Emergency surgery practice is absolutely necessary in this training. All the 17 university formative hand surgery units listed by the French College of Hand Surgeons are members of the FESUM (European Federation of the Emergency Hand Units

  10. Hydraulic fracture during epithelial stretching

    Science.gov (United States)

    Casares, Laura; Vincent, Romaric; Zalvidea, Dobryna; Campillo, Noelia; Navajas, Daniel; Arroyo, Marino; Trepat, Xavier

    2015-03-01

    The origin of fracture in epithelial cell sheets subject to stretch is commonly attributed to excess tension in the cells’ cytoskeleton, in the plasma membrane, or in cell-cell contacts. Here, we demonstrate that for a variety of synthetic and physiological hydrogel substrates the formation of epithelial cracks is caused by tissue stretching independently of epithelial tension. We show that the origin of the cracks is hydraulic; they result from a transient pressure build-up in the substrate during stretch and compression manoeuvres. After pressure equilibration, cracks heal readily through actomyosin-dependent mechanisms. The observed phenomenology is captured by the theory of poroelasticity, which predicts the size and healing dynamics of epithelial cracks as a function of the stiffness, geometry and composition of the hydrogel substrate. Our findings demonstrate that epithelial integrity is determined in a tension-independent manner by the coupling between tissue stretching and matrix hydraulics.

  11. Bio-based Hydraulic Fluids

    Science.gov (United States)

    2008-04-17

    currently formulated with vegetable oils (i.e., rapeseed , sun flower, corn, soybean, canola, coconut, etc.) and synthetic ester, such as polyol ester...2008 Vegetable Oil • Excellent lubrication • Nontoxic • Biodegradable • Derived from renewable resources such as rapeseed , sunflower, corn...Mineral Oil 100 SAE 15W-40 G Rapeseed 32 Commercial HF H Polyol ester 22 MIL-PRF-32073 Grade 2 I Canola - Cooking Oil *Hydraulic fluid 3717 April

  12. Fire Resistant Aircraft Hydraulic System.

    Science.gov (United States)

    1982-07-01

    and compounds based on new experimental elastomers as well as most commercially available elastomers were screened in seeking seals that were both...for hydraulic component testing. All of the available E6.5 stock was purchased for the screening tests. However, DuPont stated that other homologs of...with the lubricity and anti-wear additive olyvan A (molybdenum oxysulphide dithiocarbamate ) added in the quantity of less than one percent by weight

  13. Wash Your Hands

    Science.gov (United States)

    ... don't have soap and clean, running water? Washing hands with soap and water is the best way to get rid of germs in most situations. If soap and water are not available, use an alcohol-based hand sanitizer [423 KB] that contains at least 60% alcohol. ...

  14. Pneumatically actuated hand tool

    NARCIS (Netherlands)

    Cool, J.C.; Rijnsaardt, K.A.

    1996-01-01

    Abstract of NL 9401195 (A) Pneumatically actuated hand tool for carrying out a mechanical operation, provided with an exchangeable gas cartridge in which the gas which is required for pneumatic actuation is stored. More particularly, the hand tool is provided with at least one pneumatic motor, at

  15. HAND INJURIES IN VOLLEYBALL

    NARCIS (Netherlands)

    BHAIRO, NH; NIJSTEN, MWN; VANDALEN, KC; TENDUIS, HJ

    We studied the long-term sequelae of hand injuries as a result of playing volleyball. In a retrospective study, 226 patients with injuries of the hand who were seen over a 5-year period at our Trauma Department, were investigated. Females accounted for 66 % of all injuries. The mean age was 26

  16. Hand measuring eqipment

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo

    This note is used in connection with a 3 x 2 hours laboratory exercise as a part of the course GEOMETRICAL METROLOGY AND MACHINE TESTING. The laboratory includes a demonstration of a series of hand measuring tools as well as a number of exercises, illustrating the use of hand measuring equipment...

  17. HAND INJURIES IN VOLLEYBALL

    NARCIS (Netherlands)

    BHAIRO, NH; NIJSTEN, MWN; VANDALEN, KC; TENDUIS, HJ

    1992-01-01

    We studied the long-term sequelae of hand injuries as a result of playing volleyball. In a retrospective study, 226 patients with injuries of the hand who were seen over a 5-year period at our Trauma Department, were investigated. Females accounted for 66 % of all injuries. The mean age was 26 years

  18. Hand Hygiene: When and How

    Science.gov (United States)

    ... handrub? How to handwash? RUB HANDS FOR HAND HYGIENE! WASH HANDS WHEN VISIBLY SOILED Duration of the entire procedure: ... from its use. When? YOUR 5 MOMENTS FOR HAND HYGIENE 1 BEFORETOUCHINGA PATIENT 2 B P ECFLOER R ...

  19. Energy consumption of an agricultural an agricultural tractor operating in dynamometer using with diesel and chicken oil biodiesel; Consumo energetico de um trator agricola operando em bancada dinamometrica com oleo diesel e biodiesel de oleo de frango

    Energy Technology Data Exchange (ETDEWEB)

    Fiorese, Diego Augusto [Universidade Estadual Paulista Julio de Mesquita Filho (FCA/UNESP), Botucatu, SP (Brazil). Fac. de Ciencias Agronomicas. Dept. de Engenharia Rural], email: dafiorese@yahoo.com.br; Dallmeyer, Arno Udo; Romano, Leonardo Nabaes; Schlosser, Jose Fernando [Universidade Federal de Santa Maria (UFSM), RS (Brazil)

    2011-07-01

    The efficiency of energy use in agricultural machinery is dependent on the efficiency of internal combustion diesel cycle, their genuine propellants. However, some biofuels may offer a better yield due to some peculiar characteristics such distinctions in calorific value. Many studies have demonstrated a better utilization of the energy content when operating with biodiesel and with binary mixtures with diesel oil. In this study, tests were conducted on a dynamometer bench to evaluate the energy consumption of a tractor engine with four cylinders and 53 kW (72 hp), operating with biodiesel and chicken oil mixture with diesel oil. In the tests were evaluated six ratios (B5, B20, B40, B60, B80 and B100). The results showed that increasing the proportion of biodiesel was favorable to improve the utilization of the energy content, thus increasing the thermal efficiency of the engine. The best result was obtained with pure biodiesel (B100) with consumption of 395.47 MJ.h{sup -1}and efficiency of 32.35%. On the other hand the witness had the lowest use B5 with 428.20 MJ.h{sup -1} and thermal efficiency of 30.67%. (author)

  20. Hydraulic Redistribution: A Modeling Perspective

    Science.gov (United States)

    Daly, E.; Verma, P.; Loheide, S. P., III

    2014-12-01

    Roots play a key role in the soil water balance. They extract and transport water for transpiration, which usually represents the most important soil water loss in vegetated areas, and can redistribute soil water, thereby increasing transpiration rates and enhancing root nutrient uptake. We present here a two-dimensional model capable of describing two key aspects of root water uptake: root water compensation and hydraulic redistribution. Root water compensation is the ability of root systems to respond to the reduction of water uptake from areas of the soil with low soil water potential by increasing the water uptake from the roots in soil parts with higher water potential. Hydraulic redistribution is a passive transfer of water through the root system from areas of the soil with greater water potential to areas with lower water potential. Both mechanisms are driven by gradients of water potential in the soil and the roots. The inclusion of root water compensation and hydraulic redistribution in models can be achieved by describing root water uptake as a function of the difference in water potential between soil and root xylem. We use a model comprising the Richards equation for the water flow in variably saturated soils and the Darcy's equation for the water flow in the xylem. The two equations are coupled via a sink term, which is assumed to be proportional to the difference between soil and xylem water potentials. The model is applied in two case studies to describe vertical and horizontal hydraulic redistribution and the interaction between vegetation with different root depths. In the case of horizontal redistribution, the model is used to reproduce the fluxes of water across the root system of a tree subjected to uneven irrigation. This example can be extended to situations when only part of the root system has access to water, such as vegetation near creeks, trees at the edge of forests, and street trees in urban areas. The second case is inspired by recent

  1. About Hand Surgery

    Science.gov (United States)

    ... us eat, dress, write, earn a living, create art and do many other activities. To accomplish these ... 2009 American Society for Surgery of the Hand. Definition developed by ASSH Council. Other Links CME Mission ...

  2. Osteoarthritis of the Hand

    Science.gov (United States)

    ... Therapist? Media Find a Hand Surgeon Home Anatomy Osteoarthritis Email to a friend * required fields From * To * ... for those with osteoarthritis. TREATMENT The Diagnosis of Osteoarthritis When diagnosing osteoarthritis, your doctor will ask you ...

  3. Stiffness in the Hand

    Science.gov (United States)

    ... include: Arthritis Fractures Dislocations Bad sprains Tendon and muscle injuries Evaluating Hand Stiffness Your doctor will ask when the stiffness ... scan. CAUSES SIGNS AND ... stretching exercises for the joints and muscles to help loosen them. Different types of splints ...

  4. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... captioning. Videos are prepared for different audiences including, children, parents, and public health professionals. More > Hand Hygiene ... captioning. Videos are prepared for different audiences including, children, parents, and public health professionals. More > File Formats ...

  5. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... get more than a million infections in the hospital while being treated for something else. The best ... reminding healthcare providers to practice hand hygiene in hospitals and other healthcare facilities. Release Date: 8/4/ ...

  6. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... To Health (4:17) Vital Signs High Blood Pressure Spanish Diseases & Conditions Hablemos de la Influenza Influenza ... Videos are prepared for different audiences including, children, parents, and public health professionals. More > Hand Hygiene Saves ...

  7. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... Lives shows how patients can play an active role in reminding healthcare providers to practice hand hygiene ... Director for Communication, Division of News and Electronic Media Email Recommend Tweet YouTube Instagram Listen Watch RSS ...

  8. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... Please Parents Want To Do What′s Best The Obesity Epidemic Outbreaks CDC: Protecting Americans through Global Health ... captioning. Videos are prepared for different audiences including, children, parents, and public health professionals. More > Hand Hygiene ...

  9. Hand lotion poisoning

    Science.gov (United States)

    ... lotion or cream can be harmful if swallowed: Dimethicone Mineral oil Paraffins (waxes) Petrolatum Various alcohols Where ... Hand cream poisoning References Caraccio TR, McFee RB. Cosmetics and toilet articles. In: Shannon MW, Borron SW, ...

  10. Second Hand Smoke: Danger

    Science.gov (United States)

    ... What's this? Submit Button Past Emails Second Hand Smoke: Danger! Recommend on Facebook Tweet Share Compartir Make ... the United States are still exposed to secondhand smoke, even though cigarette smoking rates are dropping and ...

  11. Mind the hand

    DEFF Research Database (Denmark)

    Davidsen, Jacob; Christiansen, Ellen Tove

    2014-01-01

    , to construct and problem solve, and to show and imitate. The analyses show how a space emerges from the interaction between the children and the touchscreen, and how their hand movements reveal intelligence-as-action. Three situations with three different pairs were analysed to explore how children use......Apart from touching the screen, what is the role of the hands for children collaborating around touchscreens? Based on embodied and multimodal interaction analysis of 8- and 9-year old pairs collaborating around touchscreens, we conclude that children use their hands to constrain and control access...... their hands in activities around touchscreens, focusing in particular on how they collaborate. The analysis presented here is part of a research study on the use of touchscreens in children’s embodied and multimodal collaborative learning activities in their everyday classrooms. The general aim of the study...

  12. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... Thinking The Value of Systems Thinking (10:09) Systems Mapping: The Basics ... how patients can play an active role in reminding healthcare providers to practice hand hygiene in hospitals and ...

  13. Vibrations of hydraulic pump and their solution

    OpenAIRE

    Dobšáková Lenka; Nováková Naděžda; Habán Vladimír; Hudec Martin; Jandourek Pavel

    2017-01-01

    The vibrations of hydraulic pump and connected pipeline system are very problematic and often hardly soluble. The high pressure pulsations of hydraulic pump with the double suction inlet are investigated. For that reason the static pressure and accelerations are measured. The numerical simulations are carried out in order to correlate computed data with experimental ones and assess the main source of vibrations. Consequently the design optimization of the inner hydraulic part of pump is done ...

  14. Mitigation method of thermal transient stress by a total analysis of thermal hydraulic and structural phenomena

    Energy Technology Data Exchange (ETDEWEB)

    Kasahara, Naoto [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center; Jinbo, Masakazu [Toshiba Co., Tokyo (Japan); Hosogai, Hiromi [Joyo Industry Co., Ltd., Tokai, Ibaraki (Japan)

    2002-09-01

    This study proposes a mitigation method of thermal transient loads in fast reactor components by utilizing relationships among plant system parameters and resulting thermal stresses. Conventional design procedure against thermal transient loads has two independent steps: thermal hydraulic analysis to determine conservative thermal transient conditions considering variation of the system parameters and structural analysis to check structural integrity under given conditions. On the other hand, a total analysis procedure of thermal hydraulic and structural phenomena can grasp the relationship among system parameters and thermal stresses. It enables the mitigation of thermal transient loads by adjusting system parameters. (author)

  15. Hydraulically Driven Grips For Hot Tensile Specimens

    Science.gov (United States)

    Bird, R. Keith; Johnson, George W.

    1994-01-01

    Pair of grips for tensile and compressive test specimens operate at temperatures up to 1,500 degrees F. Grips include wedges holding specimen inside furnace, where heated to uniform temperature. Hydraulic pistons drive wedges, causing them to exert clamping force. Hydraulic pistons and hydraulic fluid remain outside furnace, at room temperature. Cooling water flows through parts of grips to reduce heat transferred to external components. Advantages over older devices for gripping specimens in high-temperature tests; no need to drill holes in specimens, maintains constant gripping force on specimens, and heated to same temperature as that of specimen without risk of heating hydraulic fluid and acuator components.

  16. Design and Analysis of Hydraulic Chassis with Obstacle Avoidance Function

    Science.gov (United States)

    Hong, Yingjie; Zhang, Xiang

    2017-07-01

    This article mainly expounds the design of hydraulic system for the hydraulic chassis with obstacle avoidance function. Including the selection of hydraulic motor wheels, hydraulic pump, digital hydraulic cylinder and the matching of engine power. And briefly introduces the principle of obstacle avoidance.

  17. Hands of early primates.

    Science.gov (United States)

    Boyer, Doug M; Yapuncich, Gabriel S; Chester, Stephen G B; Bloch, Jonathan I; Godinot, Marc

    2013-12-01

    Questions surrounding the origin and early evolution of primates continue to be the subject of debate. Though anatomy of the skull and inferred dietary shifts are often the focus, detailed studies of postcrania and inferred locomotor capabilities can also provide crucial data that advance understanding of transitions in early primate evolution. In particular, the hand skeleton includes characteristics thought to reflect foraging, locomotion, and posture. Here we review what is known about the early evolution of primate hands from a comparative perspective that incorporates data from the fossil record. Additionally, we provide new comparative data and documentation of skeletal morphology for Paleogene plesiadapiforms, notharctines, cercamoniines, adapines, and omomyiforms. Finally, we discuss implications of these data for understanding locomotor transitions during the origin and early evolutionary history of primates. Known plesiadapiform species cannot be differentiated from extant primates based on either intrinsic hand proportions or hand-to-body size proportions. Nonetheless, the presence of claws and a different metacarpophalangeal [corrected] joint form in plesiadapiforms indicate different grasping mechanics. Notharctines and cercamoniines have intrinsic hand proportions with extremely elongated proximal phalanges and digit rays relative to metacarpals, resembling tarsiers and galagos. But their hand-to-body size proportions are typical of many extant primates (unlike those of tarsiers, and possibly Teilhardina, which have extremely large hands). Non-adapine adapiforms and omomyids exhibit additional carpal features suggesting more limited dorsiflexion, greater ulnar deviation, and a more habitually divergent pollex than observed plesiadapiforms. Together, features differentiating adapiforms and omomyiforms from plesiadapiforms indicate increased reliance on vertical prehensile-clinging and grasp-leaping, possibly in combination with predatory behaviors in

  18. Helical coil thermal hydraulic model

    Science.gov (United States)

    Caramello, M.; Bertani, C.; De Salve, M.; Panella, B.

    2014-11-01

    A model has been developed in Matlab environment for the thermal hydraulic analysis of helical coil and shell steam generators. The model considers the internal flow inside one helix and its associated control volume of water on the external side, both characterized by their inlet thermodynamic conditions and the characteristic geometry data. The model evaluates the behaviour of the thermal-hydraulic parameters of the two fluids, such as temperature, pressure, heat transfer coefficients, flow quality, void fraction and heat flux. The evaluation of the heat transfer coefficients as well as the pressure drops has been performed by means of the most validated literature correlations. The model has been applied to one of the steam generators of the IRIS modular reactor and a comparison has been performed with the RELAP5/Mod.3.3 code applied to an inclined straight pipe that has the same length and the same elevation change between inlet and outlet of the real helix. The predictions of the developed model and RELAP5/Mod.3.3 code are in fairly good agreement before the dryout region, while the dryout front inside the helical pipes is predicted at a lower distance from inlet by the model.

  19. Hand Models Emerge in China

    Institute of Scientific and Technical Information of China (English)

    CHENGTIELIANG

    2003-01-01

    CHINESE women have now discovered that beautiful hands are realizable assets. A new career invites those with shapely hands: that of hand model. This nascent profession has great prospects, as images involving hands are essential in the advertising business for promotion of such products as jewelry, watches and cell phones. Certain film stars also employ standins for hand close-ups.

  20. Laboratory testing of airborne brake wear particle emissions using a dynamometer system under urban city driving cycles

    Science.gov (United States)

    Hagino, Hiroyuki; Oyama, Motoaki; Sasaki, Sousuke

    2016-04-01

    To measure driving-distance-based mass emission factors for airborne brake wear particulate matter (PM; i.e., brake wear particles) related to the non-asbestos organic friction of brake assembly materials (pads and lining), and to characterize the components of brake wear particles, a brake wear dynamometer with a constant-volume sampling system was developed. Only a limited number of studies have investigated brake emissions under urban city driving cycles that correspond to the tailpipe emission test (i.e., JC08 or JE05 mode of Japanese tailpipe emission test cycles). The tests were performed using two passenger cars and one middle-class truck. The observed airborne brake wear particle emissions ranged from 0.04 to 1.4 mg/km/vehicle for PM10 (particles up to 10 μm (in size), and from 0.04 to 1.2 mg/km/vehicle for PM2.5. The proportion of brake wear debris emitted as airborne brake wear particles was 2-21% of the mass of wear. Oxygenated carbonaceous components were included in the airborne PM but not in the original friction material, which indicates that changes in carbon composition occurred during the abrasion process. Furthermore, this study identified the key tracers of brake wear particles (e.g., Fe, Cu, Ba, and Sb) at emission levels comparable to traffic-related atmospheric environments.

  1. Development of an Industry Dynamometer/Spin Test Facility--Equipment Only: Cooperative Research and Development Final Report, CRADA Number CRD-05-164

    Energy Technology Data Exchange (ETDEWEB)

    McDade, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-12-01

    The Department of Energy/National Renewable Energy Laboratory (DOE/NREL) owns and operates a megawatt-scale dynamometer used for testing wind turbine drive trains up to 1.5 megawatt (MW) in rated capacity. At this time, this unit is the only unit of its type in the United States, available for use by the American Wind Industry. Currently this dynamometer is heavily backlogged and unavailable to provide testing needed by various wind industry members. DOE/NREL is in possession of two critical pieces of equipment that may be used to develop an alternative Dynamometer facility, but does not have the funds or other resources necessary to develop such a facility. The Participant possesses complimentary facilities and infrastructure that when combined with the NREL equipment can create such a test facility. The Participant is also committed to expending funds to develop and operate such a facility to the subsequent benefit of the Wind Industry and DOE Wind Energy program. In exchange for DOE/NREL providing the critical equipment, the Participant will grant DOE/NREL a minimum of 90 days of testing time per year in the new facility while incurring no facilities fees.

  2. Hand eczema: An update

    Directory of Open Access Journals (Sweden)

    Chembolli Lakshmi

    2012-01-01

    Full Text Available Eczema, the commonest disorders afflicting the hands, is also the commonest occupational skin disease (OSD. In the dermatology outpatient departments, only the severe cases are diagnosed since patients rarely report with early hand dermatitis. Mild forms are picked up only during occupational screening. Hand eczema (HE can evolve into a chronic condition with persistent disease even after avoiding contact with the incriminated allergen / irritant. The important risk factors for hand eczema are atopy (especially the presence of dermatitis, wet work, and contact allergy. The higher prevalence in women as compared to men in most studies is related to environmental factors and is mainly applicable to younger women in their twenties. Preventive measures play a very important role in therapy as they enable the affected individuals to retain their employment and livelihood. This article reviews established preventive and therapeutic options and newer drugs like alitretinoin in hand eczema with a mention on the etiology and morphology. Identifying the etiological factors is of paramount importance as avoiding or minimizing these factors play an important role in treatment.

  3. WATER ENERGY IN HYDROAMELIORATIVE SYSTEMS USING THE HYDRAULIC TRANSFORMER TYPE A. BARGLAZAN AND THE HYDRAULIC HAMMER (HYDRAULIC PUMP

    Directory of Open Access Journals (Sweden)

    Teodor Eugen Man

    2010-01-01

    Full Text Available This paper presents two examples of exploitation of water energy that can be used in the irrigation field. First of theseexamples is the hydraulic transformer type A. Barglazan used for irrigation, pumped water is taken directly from theriver’s well, using a hydraulic pump which simultaneously carried out a double transformation in this way: hydraulicenergy into mechanic energy and mechanical energy into hydraulic energy. Technology preparation and devices designwas done in record time, seeing that this constructive solution is more robust, reliable and with improved energyperformance versus the laboratory prototype. The experimental research which was made at 1:1 scale proved theirgood function over time. Another example is the hydraulic hammer (hydraulic pump that uses low-head energy topump water, with a global efficiency of about 10 - 50%. Currently, the new situation of private ownership of landprovides conditions for new pumping microstations to be made where irrigation is necessary and optimal hydrauliclocations exist.

  4. Kinetic measurements of hand motor impairments after mild to moderate stroke using grip control tasks.

    Science.gov (United States)

    Ye, Yu; Ma, Le; Yan, Tiebin; Liu, Huihua; Wei, Xijun; Song, Rong

    2014-05-11

    The aim of this study is to investigate quantitative outcome measurements of hand motor performance for subjects after mild to moderate stroke using grip control tasks and characterize abnormal flexion synergy of upper extremities after stroke. A customized dynamometer with force sensors was used to measure grip force and calculate rotation torque during the sub-maximal grip control tasks. The paretic and nonpartic sides of eleven subjects after stroke and the dominant sides of ten healthy persons were tested. Their maximal voluntary grip force was measured and used to set sub-maximal grip control tasks at three different target force levels. Force control ability was characterized by the maximal grip force, mean force percentage, coefficient of variation (CV), target deviation ratio (TDR), and rotation torque ratio (RTR). The motor impairments of subjects after stroke were also evaluated using the Fugl-Meyer assessment for upper extremity (FMA-UE) and Wolf Motor Function Test (WMFT). Maximal grip force of the paretic side was significantly reduced as compared to the nonparetic side and the healthy group, while the difference of maximal grip force between the nonparetic side and the healthy group was not significant. TDR and RTR increased for all three groups with increasing target force level. There were significant differences of CV, TDR and RTR between the paretic side and the healthy group at all the force levels. CV, TDR and RTR showed significant negative correlations with FMA-UE and WMFT at 50% of maximum grip force. This study designed a customized dynamometer together with an innovative measurement, RTR, to investigate the hand motor performance of subjects after mild to moderate stroke during force control tasks. And stroke-induced abnormal flexion synergy of wrist and finger muscles could be characterized by RTR. This study also identified a set of kinetic parameters which can be applied to quantitatively assess the hand motor function of subjects after

  5. HYDRAULIC CHARACTERISTICS OF VERTICAL VORTEX AT HYDRAULIC INTAKES

    Institute of Scientific and Technical Information of China (English)

    CHEN Yun-liang; WU Chao; YE Mao; JU Xiao-ming

    2007-01-01

    The trace of vertical vortex flow at hydraulic intakes is of the shape of spiral lines, which was observed in the presented experiments with the tracer technique. It represents the fluid particles flow spirally from the water surface to the underwater and rotate around the vortex-axis multi-cycle. This process is similar to the movement of screw. To describe the multi-circle spiral characteristics under the axisymmetric condition, the vertical vortex would change not only in the radial direction but also in the axial direction. The improved formulae for three velocity components for the vertical vortex flow were deduced by using the method of separation of variables in this article. In the improved formulae, the velocity components are the functions of the radial and axial coordinates, so the multi-circle spiral flow of vertical vortex could be simulated. The calculated and measured results for the vertical vortex flow were compared and the causes of errors were analyzed.

  6. Three-Fingered Robot Hand

    Science.gov (United States)

    Ruoff, C. F.; Salisbury, J. K.

    1984-01-01

    Mechanical joints and tendons resemble human hand. Robot hand has three "human-like" fingers. "Thumb" at top. Rounded tips of fingers covered with resilient material provides high friction for griping. Hand potential as prosthesis for humans.

  7. Design of Pumps for Water Hydraulic Systems

    DEFF Research Database (Denmark)

    Klit, Peder; Olsen, Stefan; Bech, Thomas Nørgaard

    1999-01-01

    This paper considers the development of two pumps for water hydraulic applications. The pumps are based on two different working principles: The Vane-type pump and the Gear-type pump. Emphasis is put on the considerations that should be made to account for water as the hydraulic fluid.......KEYWORDS: water, pump, design, vane, gear....

  8. Hydraulic fracturing with distinct element method

    NARCIS (Netherlands)

    Pruiksma, J.P.; Bezuijen, A.

    2002-01-01

    In this report, hydraulic fracturing is investigated using the distinct element code PFC2D from Itasca. Special routines were written to be able to model hydraulic fracturing. These include adding fluid flow to PFC2D and updating the fluid flow domains when fractures appear. A brief description of t

  9. Hydraulic Actuator for Ganged Control Rods

    Science.gov (United States)

    Thompson, D. C.; Robey, R. M.

    1986-01-01

    Hydraulic actuator moves several nuclear-reactor control rods in unison. Electromagnetic pump pushes liquid lithium against ends of control rods, forcing them out of or into nuclear reactor. Color arrows show lithium flow for reactor startup and operation. Flow reversed for shutdown. Conceived for use aboard spacecraft, actuator principle applied to terrestrial hydraulic machinery involving motion of ganged rods.

  10. Control arrangement for the actuation of hydraulic consumers

    Energy Technology Data Exchange (ETDEWEB)

    Kussel, W.; Dettmers, M.; Weirich, W.

    1988-11-09

    An arrangement for controlling the actuation of hydraulic consumers, by selectively connecting the consumers to hydraulic pressure and return lines; the control arrangement comprising a respective hydraulically operated directional control valve associated with each of the hydraulic consumers, a respective electro-magnetically operated pre-control valve associated with each of the hydraulic directional control valves, and further electro-magnetically operated directional control valve means associated with the pre-control valves, each of the hydraulic consumers being connectible to the hydraulic pressure or return lines via the associated hydraulically operated directional control valve which is actuatable by a hydraulic control line leading from the output of the associated pre-control valve, wherein the inputs of the pre-control valves are connected directly to the hydraulic return line and indirectly, via the further control valve means, to the hydraulic return line or to a hydraulic control pressure line.

  11. Comparison of surgical hand scrub and alcohol surgical hand rub on reducing hand microbial burden.

    Science.gov (United States)

    Ghorbani, Azam; Shahrokhi, Akram; Soltani, Zahra; Molapour, Azam; Shafikhani, Mahin

    2012-02-01

    This study was performed to compare the effects of two hand decontamination methods on the microbial burden of operating room staff hands. The surgical hand washing methods compared were a traditional surgical hand scrub using a povidone iodine solution, and a social wash using a liquid non-antibacterial soap followed by the application of an alcoholic hand rub.

  12. Gravity-Driven Hydraulic Fractures

    Science.gov (United States)

    Germanovich, L. N.; Garagash, D.; Murdoch, L. C.; Robinowitz, M.

    2014-12-01

    This study is motived by a new method for disposing of nuclear waste by injecting it as a dense slurry into a hydraulic fracture that grows downward to great enough depth to permanently isolate the waste. Disposing of nuclear waste using gravity-driven hydraulic fractures is mechanically similar to the upward growth of dikes filled with low density magma. A fundamental question in both applications is how the injected fluid controls the propagation dynamics and fracture geometry (depth and breadth) in three dimensions. Analog experiments in gelatin [e.g., Heimpel and Olson, 1994; Taisne and Tait, 2009] show that fracture breadth (the short horizontal dimension) remains nearly stationary when the process in the fracture "head" (where breadth is controlled) is dominated by solid toughness, whereas viscous fluid dissipation is dominant in the fracture tail. We model propagation of the resulting gravity-driven (buoyant or sinking), finger-like fracture of stationary breadth with slowly varying opening along the crack length. The elastic response to fluid loading in a horizontal cross-section is local and can be treated similar to the classical Perkins-Kern-Nordgren (PKN) model of hydraulic fracturing. The propagation condition for a finger-like crack is based on balancing the global energy release rate due to a unit crack extension with the rock fracture toughness. It allows us to relate the net fluid pressure at the tip to the fracture breadth and rock toughness. Unlike the PKN fracture, where breadth is known a priori, the final breadth of a finger-like fracture is a result of processes in the fracture head. Because the head is much more open than the tail, viscous pressure drop in the head can be neglected leading to a 3D analog of Weertman's hydrostatic pulse. This requires relaxing the local elasticity assumption of the PKN model in the fracture head. As a result, we resolve the breadth, and then match the viscosity-dominated tail with the 3-D, toughness

  13. Scaling hydraulic properties of a macroporous soil

    Science.gov (United States)

    Mohanty, Binayak P.

    1999-06-01

    Macroporous soils exhibit significant differences in their hydraulic properties for different pore domains. Multimodal hydraulic functions may be used to describe the characteristics of multiporosity media. I investigated the usefulness of scaling to describe the spatial variability of hydraulic conductivity (K(-h)) functions of a macroporous soil in Las Nutrias, New Mexico. Piecewise-continuous hydraulic conductivity functions suitable for macroporous soils in conjunction with a hybrid similar media-functional normalization scaling approach were used. Results showed that gravity-dominated flow and the related hydraulic conductivity (K(minus;h) functions of the macropore region are more readily scalable than capillary-dominated flow properties of the mesopore and micropore regions. A possible reason for this behavior is that gravity-dominated flow in the larger pores is mostly influenced by the pore diameter which remains more uniform as compared to tortuous mesopores and micropores with variable neck and body sizes along the pore length.

  14. Hydraulic conductivity of GCLs in MSW landfills

    Institute of Scientific and Technical Information of China (English)

    LI Guo-cheng; YANG Wu-chao; DAN Tang-hui

    2008-01-01

    The state of the art of the study on the hydraulic conductivity of GCLs is presented in terms of the in-fluence of the effective stress, chemical interactions, freeze - thaw cycles and temperature gradients. The chan-ges of void ratio caused by changes of effective stress have a direct linear effect on the hydraulic conductivity, regardless of the cation concentration or the thickness of the adsorbed layer. The hydraulic conductivity is relat-ed to the relative abundance of monovalent and divalent cation(RMD), and RMD has a great effect on the hy-draulic conductivity in weak solution. The long-term susceptibility of GCLs to increased hydraulic conductivity as a response to repeated freeze-thaw cycling is minimal, which has been proved after 150 freeze-thaw cycles. The potential of desiccation cracking increases with the increasing temperature gradient and is related to the ini-tial subsoil water content, the applied overburden stress, etc.

  15. Modeling and Simulation of Hydraulic Engine Mounts

    Institute of Scientific and Technical Information of China (English)

    DUAN Shanzhong; Marshall McNea

    2012-01-01

    Hydraulic engine mounts are widely used in automotive powertrains for vibration isolation.A lumped mechanical parameter model is a traditional approach to model and simulate such mounts.This paper presents a dynamical model of a passive hydraulic engine mount with a double-chamber,an inertia track,a decoupler,and a plunger.The model is developed based on analogy between electrical systems and mechanical-hydraulic systems.The model is established to capture both low and high frequency dynatmic behaviors of the hydraulic mount.The model will be further used to find the approximate pulse responses of the mounts in terms of the force transmission and top chamber pressure.The close form solution from the simplifiod linear model may provide some insight into the highly nonlinear behavior of the mounts.Based on the model,computer simulation has been carried out to study dynamic performance of the hydraulic mount.

  16. Hydraulic test for evaluation of hydrophone VSP

    Energy Technology Data Exchange (ETDEWEB)

    Yabuuchi, Satoshi; Koide, Kaoru [Power Reactor and Nuclear Fuel Development Corp., Toki, Gifu (Japan). Tono Geoscience Center

    1997-12-01

    This hydraulic test was carried out at the test site of Tono Geoscience Center, Mizunami-shi, Gifu Pref. in order to evaluate the reliability of the hydraulic conductivity estimated from hydrophone VSP experiment. From March to April 1997, we carried out measurements of pore-water pressure at five depths and permeability tests at seven depths down to G.L.-300m, within a borehole drilled in granitic rock. We compared the results of hydraulic test with hydrophone VSP experiment on condition that a single open fracture existed, and we obtained two notable results. First, for the granitic rock at which a single open fracture was found by BTV and also detected by hydrophone VSP experiment, the hydraulic conductivity was 1.54 x 10{sup -7} cm/sec, while for the same granitic rock at which another single open fracture was found by BTV but not detected by hydrophone VSP experiment, the hydraulic conductivity was less than 6 x 10{sup -10} cm/sec. Second, we converted the hydraulic conductivity of 1.54 x 10{sup -7} cm/sec which was obtained in a hydraulic test section of length 2.5 m into an equivalent value for a single open fracture of width 1 mm. The converted value (3.8 x 10{sup -4} cm/sec) was similar to the hydraulic conductivity estimated from hydrophone VSP experiment. In conclusion, the hydraulic test result shows that hydrophone VSP is useful to estimate an approximate hydraulic conductivity of a single open fracture. (author)

  17. Design and evaluation of two different finger concepts for body-powered prosthetic hand.

    Science.gov (United States)

    Smit, Gerwin; Plettenburg, Dick H; van der Helm, Frans C T

    2013-01-01

    The goal of this study was to find an efficient method of energy transmission for application in an anthropomorphic underactuated body-powered (BP) prosthetic hand. A pulley-cable finger and a hydraulic cylinder finger were designed and tested to compare the pulley-cable transmission principle with the hydraulic cylinder transmission principle. Both fingers had identical dimensions and a low mass. The only thing that differed between the fingers was the transmission principle. The input energy was measured for a number of tasks. The pulley-cable finger required more input energy than the hydraulic cylinder finger to perform the tasks. This was especially the case in tasks that required high pinch forces. The hydraulic cylinder transmission is therefore the more efficient transmission for application in BP prosthetic fingers.

  18. DLC coatings for hydraulic applications

    Institute of Scientific and Technical Information of China (English)

    Luca NOBILI; Luca MAGAGNIN

    2009-01-01

    Replacement of lubricating oils with water or low-viscosity fluids is highly desirable in many industrial fields, on account of the environmental and economical advantages. Low lubricity of water might be insufficient for proper operation of hydraulic components, and diamond-like carbon(DLC) coatings are very attractive as solid lubricant films. A remote-plasma PACVD process was utilized to deposit hydrogenated DLC coatings (a-C:H) on different substrates. Microindentation measurements show that the coating hardness is around 35 GPa. Tribological behavior was evaluated by block-on-ring tests performed in water and water with alumina. The wear rate was calculated after measuring the wear volume by a laser profilemeter. Morphological and compositional analysis of the wear tracks reveal that coating failure may occur by abrasive wear or delamination, depending on the substrate properties. Hard and smooth substrates give the best results and dispersed alumina particles increase the wear rate.

  19. Aircraft Hydraulic Systems Dynamic Analysis

    Science.gov (United States)

    1978-10-01

    4400 PSIG OUTLET PRESSURE ~’f UM5 S1 l .( FIF ~0RV lR 1 .I. AP (c R (V) IFWM) APPROX C ASE !VPý :iI S ReUN N•;MRF.. r p kN i t, isI A! f IN, I:E • ’l...and 1F.GI pump modelo were assumed from data supplied by CECO. 165 _ -- --- - SECTION V HYDRAULIC MOTOR MODEL DEVELOPMENT AND VERIFICATION A fixed...3 70 P.,0 601 ~4 M24.0 3 1p ’, 4 r I 1 1 ISIS 2411 APPENDIX E (CONT.) HSFR TECHNICAL MANUAL (AFAPL-TR-76-43, VOL. IV) 4.15 VANE PU`MP SUBROUTINE 4.15A

  20. Wash Your Hands

    Centers for Disease Control (CDC) Podcasts

    2010-03-08

    This video shows kids how to properly wash their hands, one of the most important steps we can take to avoid getting sick and spreading germs to others.  Created: 3/8/2010 by Centers for Disease Control and Prevention (CDC).   Date Released: 3/8/2010.

  1. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... practice hand hygiene in hospitals and other healthcare facilities. Release Date: 8/4/2010 Source: Healthcare-associated ... choose "Save target as…", save file in desired location. Firefox/Chrome: Right-click on the link, choose " ...

  2. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... CDC-TV videos cover a variety of health, safety and preparedness topics and include closed-captioning. Videos are prepared for different audiences including, children, parents, and public health professionals. More > Hand Hygiene Saves Lives (5:10) Recommend on Facebook Tweet ...

  3. De hand van Huizinga

    NARCIS (Netherlands)

    Huizinga, Johan

    2009-01-01

    De hand van Huizinga bevat een nieuwe selectie van de belangrijkste essays uit het omvangrijke oeuvre van de wereldberoemde Nederlandse historicus Johan Huizinga. Deze essays en studies zijn geselecteerd op basis van de diverse disciplines waarmee Huizinga zich bezighield - van de Middeleeuwen tot

  4. Shanghai Hand Puppet Tcoupe

    Institute of Scientific and Technical Information of China (English)

    1993-01-01

    PUPPETRY n ancient artform, has had difficulties ca-tering to children’s aesthet-ic needs and perceptions.ShanghaiHand Puppet Troupe has,however,successfully reached children audi-ences with its new science fictlonpiece,Nuozha Meets the Inhabitants of Tai star.

  5. Hands-On Hydrology

    Science.gov (United States)

    Mathews, Catherine E.; Monroe, Louise Nelson

    2004-01-01

    A professional school and university collaboration enables elementary students and their teachers to explore hydrology concepts and realize the beneficial functions of wetlands. Hands-on experiences involve young students in determining water quality at field sites after laying the groundwork with activities related to the hydrologic cycle,…

  6. Passive hand prostheses.

    Science.gov (United States)

    Soltanian, Hooman; de Bese, Genevieve; Beasley, Robert W

    2003-02-01

    For many mangled hands, appropriately designed passive prostheses now available, alone or in conjunction with surgical reconstruction, can offer the best available improvement, provided they are of high quality and backed by prompt and reliable after-delivery services. Invariably, there is improvement in physical capability along with restoration of good social presentation.

  7. Put Your Hands Together

    Centers for Disease Control (CDC) Podcasts

    2011-03-24

    In this podcast, learn how to help stop the spread of infection and stay healthy. It's easy when you 'Put Your Hands Together.'.  Created: 3/24/2011 by National Center for Preparedness, Detection, and Control of Infectious Diseases (NCPDCID) and National Center for Zoonotic, Vector-Borne, and Enteric Diseases (NCZVED).   Date Released: 3/24/2011.

  8. Man and his hand

    NARCIS (Netherlands)

    J.C.H.M. van der Meulen (Jacques)

    1976-01-01

    textabstractIntroduction: In a world where mechanisation and automation have led to a devaluation of skilled manual work, and where only certain press and publicity media doubt the superiority of the mind, the following operating-theatre dialogue is refreshing: Surgeon: The surgeon's hands are his f

  9. Hands-On Hydrology

    Science.gov (United States)

    Mathews, Catherine E.; Monroe, Louise Nelson

    2004-01-01

    A professional school and university collaboration enables elementary students and their teachers to explore hydrology concepts and realize the beneficial functions of wetlands. Hands-on experiences involve young students in determining water quality at field sites after laying the groundwork with activities related to the hydrologic cycle,…

  10. Rotationally Actuated Prosthetic Hand

    Science.gov (United States)

    Norton, William E.; Belcher, Jewell G., Jr.; Carden, James R.; Vest, Thomas W.

    1991-01-01

    Prosthetic hand attached to end of remaining part of forearm and to upper arm just above elbow. Pincerlike fingers pushed apart to degree depending on rotation of forearm. Simpler in design, simpler to operate, weighs less, and takes up less space.

  11. A Ground-Based Comparison of the Muscle Atrophy Research and Exercise System (MARES) and a Standard Isokinetic Dynamometer

    Science.gov (United States)

    Hackney, K. J.; English, K. L.; Redd, E.; DeWitt, J. K.; Ploutz-Snyder, R.; Ploutz-Snyder, L. L.

    2010-01-01

    PURPOSE: 1) To compare the test-to-test reliability of Muscle Atrophy Research and Exercise System (MARES) with a standard laboratory isokinetic dynamometer (ISOK DYN) and; 2) to determine if measures of peak torque and total work differ between devices. METHODS: Ten subjects (6M, 4F) completed two trials on both MARES and an ISOK DYN in a counterbalanced order. Peak torque values at 60 deg & 180 deg / s were obtained from five maximal repetitions of knee extension (KE) and knee flexion (KF). Total work at 180 deg / s was determined from the area under the torque vs. displacement curve during twenty maximal repetitions of KE and KF. Reliability of measures within devices was interpreted from the intraclass correlation coefficient (ICC) and compared between devices using the ratio of the within-device standard deviations. Indicators of agreement for the two devices were evaluated from: 1) a calculation of concordance (rho) and; 2) the correlation between the mean of measures versus the delta difference between measures (m u vs delta). RESULTS: For all outcome measures ICCs were high for both the ISOK DYN (0.95-0.99) and MARES (0.90-0.99). However, ratios of the within-device standard deviation were 1.3 to 4.3 times higher on MARES. On average, a wide range (3.3 to 1054 Nm) of differences existed between the values obtained. Only KE peak torque measured at 60 deg & 180 deg / s showed similarities between devices (rho = 0.91 & 0.87; Pearson's r for m u vs delta = -0.22 & -0.37, respectively). CONCLUSION: Although MARES was designed for use in microgravity it was quite reliable during ground-based testing. However, MARES was consistently more variable than an ISOK DYN. Future longitudinal studies evaluating a change in isokinetic peak torque or total work should be limited within one device.

  12. Morphological and semi-quantitative characteristics of diesel soot agglomerates emitted from commercial vehicles and a dynamometer

    Institute of Scientific and Technical Information of China (English)

    LUO Chin-Hsiang; LEE Whei-May; LIAW Jiun-Jian

    2009-01-01

    Diesel soot aggregates emitted from a model dynamometer and 11 on-road vehicles were segregated by a micro-orifice uniform deposit impactor (MOUDI). The elemental contents and morphological parameters of the aggregates were then examined by scanning electron microscopy coupled with an energy dispersive spectrometer (SEM-EDS), and combined with a fractional Brownian motion (fBm) processor. Two mode-size distributions of aggregates collected from diesel vehicles were confirmed. Mean mass concentration of 339 mg/m3 (dC/dlogdp) existed in the dominant mode (180-320 nm). A relatively high proportion of these aggregates appeared in PM1, accentuating the relevance regarding adverse health effects. Furthermore, the fBm processor directly parameterized the SEM images of fractal like aggregates and successfully quantified surface texture to extract Hurst coefficients (H) of the aggregates. For aggregates from vehicles equipped with a universal cylinder number, the H value was independent of engine operational conditions. A small H value existed in emitted aggregates from vehicles with a large number of cylinders. Generally, this study found that aggregate fractal dimension related to H was in the range of 1.641-1.775, which is in agreement with values reported by previous TEM-based experiments. According to EDS analysis, carbon content ranged in a high level of 30%-50% by weight for diesel soot aggregates. The presence of Na and Mg elements in these sampled aggregates indicated the likelihood that some engine enhancers composed of biofuel or surfactants were commonly used in on-road vehicles in Taiwan. In particular, the morphological H combined with carbon content detection can be useful for characterizing chain-like or cluster diesel soot aggregates in the atmosphere.

  13. Design and evaluation of two different finger concepts for body-powered prosthetic hand

    NARCIS (Netherlands)

    Smit, G.; Plettenburg, D.H.; Van der Helm, F.C.

    2014-01-01

    The goal of this study was to find an efficient method of energy transmission for application in an anthropomorphic underactuated body-powered (BP) prosthetic hand. A pulley-cable finger and a hydraulic cylinder finger were designed and tested to compare the pulley-cable transmission principle with

  14. Getting saturated hydraulic conductivity from surface Ground-Penetrating Radar measurements inside a ring infiltrometer

    Science.gov (United States)

    Leger, E.; Saintenoy, A.; Coquet, Y.

    2013-12-01

    Hydraulic properties of soils, described by the soil water retention and hydraulic conductivity functions, strongly influence water flow in the vadoze zone, as well as the partitioning of precipitation between infiltration into the soil and runoff along the ground surface. Their evaluation has important applications for modelling available water resources and for flood forecasting. It is also crucial to evaluate soil's capacity to retain chemical pollutants and to assess the potential of groundwater pollution. The determination of the parameters involved in soil water retention functions, 5 parameters when using the van Genuchten function, is usually done by laboratory experiments, such as the water hanging column. Hydraulic conductivity, on the other hand can be estimated either in laboratory, or in situ using infiltrometry tests. Among the large panel of existing tests, the single or double ring infiltrometers give the field saturated hydraulic conductivity by applying a positive charge on soils, whereas the disk infiltrometer allows to reconstruct the whole hydraulic conductivity curve, by applying different charges smaller than or equal to zero. In their classical use, volume of infiltrated water versus time are fitted to infer soil's hydraulic conductivity close to water saturation. Those tests are time-consuming and difficult to apply to landscape-scale forecasting of infiltration. Furthermore they involve many assumptions concerning the form of the infiltration bulb and its evolution. Ground-Penetrating Radar (GPR) is a geophysical method based on electromagnetic wave propagation. It is highly sensitive to water content variations directly related to the dielectric permittivity. In this study GPR was used to monitor water infiltration inside a ring infiltrometer and retrieve the saturated hydraulic conductivity. We carried out experiments in a quarry of Fontainebleau sand, using a Mala RAMAC system with antennae centered on 1600 MHz. We recorded traces at

  15. Hand chemical burns.

    Science.gov (United States)

    Robinson, Elliot P; Chhabra, A Bobby

    2015-03-01

    There is a vast and ever-expanding variety of potentially harmful chemicals in the military, industrial, and domestic landscape. Chemical burns make up a small proportion of all skin burns, yet they can cause substantial morbidity and mortality. Additionally, the hand and upper extremity are the most frequently involved parts of the body in chemical burns, and therefore these injuries may lead to severe temporary or permanent loss of function. Despite this fact, discussion of the care of these injuries is sparse in the hand surgery literature. Although most chemical burns require only first response and wound care, some require the attention of a specialist for surgical debridement and, occasionally, skin coverage and reconstruction. Exposure to certain chemicals carries the risk of substantial systemic toxicity and even mortality. Understanding the difference between thermal and chemical burns, as well as special considerations for specific compounds, will improve patient treatment outcomes.

  16. Alien Hand Syndrome.

    Science.gov (United States)

    Hassan, Anhar; Josephs, Keith A

    2016-08-01

    Alien hand syndrome (AHS) is a rare disorder of involuntary limb movement together with a sense of loss of limb ownership. It most commonly affects the hand, but can occur in the leg. The anterior (frontal, callosal) and posterior variants are recognized, with distinguishing clinical features and anatomical lesions. Initial descriptions were attributed to stroke and neurosurgical operations, but neurodegenerative causes are now recognized as most common. Structural and functional imaging and clinical studies have implicated the supplementary motor area, pre-supplementary motor area, and their network connections in the frontal variant of AHS, and the inferior parietal lobule and connections in the posterior variant. Several theories are proposed to explain the pathophysiology. Herein, we review the literature to update advances in the understanding of the classification, pathophysiology, etiology, and treatment of AHS.

  17. Tying the Manager's Hands

    DEFF Research Database (Denmark)

    Foss, Kirsten; Foss, Nicolai Juul; Vázquez-Vicente, Xosé H.

    2003-01-01

    AbstractWe discuss and empirically examine a firm-level equivalent of the ancient problem of `tying the King's hands,' namely how to maximize managerial intervention for `good cause,' while avoiding intervention for `bad cause.' Managers may opportunistically intervene when such intervention...... produces private benefits. Overall firm performance is harmed as a result, because opportunistic managerial intervention harms employee motivation. The central point of the paper is that various mechanisms and factors, such as managers staking their personal reputation, employees controlling important...

  18. Pediatric hand treadmill injuries.

    Science.gov (United States)

    Banever, Gregory T; Moriarty, Kevin P; Sachs, Barry F; Courtney, Richard A; Konefal, Stanley H; Barbeau, Lori

    2003-07-01

    The great popularity of physical fitness in modern society has brought many pieces of exercise equipment into our homes for convenience and privacy. This trend has come with an increasing rate of injuries to children who curiously touch moving parts, including treadmill belts. Experience with a recent series of treadmill contact burns to children's hands is described in this article. A retrospective chart review at a tertiary referral center from June 1998 until June 2001 found six children sustaining hand burns from treadmills. The patients' ages at presentation ranged from 15 to 45 months (average of 31 months, three boys and three girls). All injuries occurred in the home while a parent was using the treadmill. Burns involved the palmar aspect of the hand, mostly confined to the fingers, and the severity ranged from partialto full-thickness burns. All patients were initially managed with collagenase and bacitracin zinc/polymyxin B powder dressings to second- and third-degree burns, along with splinting and range-of-motion exercises. Two patients required skin grafting at 2 weeks and 2 months for full-thickness tissue loss and tight joint contracture, respectively. At an average follow-up of 12 months, all patients had full range of motion and no physical limitation. The rate of children injured by exercise equipment is expected to increase. Friction burns to the hands remain a concern, although early recognition and appropriate management are associated with excellent functional outcomes. Protective modification of exercise machines seems to be the best approach to eliminating these injuries.

  19. Hand Hygiene Saves Lives

    Medline Plus

    Full Text Available ... Vital Signs Vital Signs – Presión Arterial Alta Other Languages Arabic احصل على التطعيم لتجنب الحصبة French Faites- ... captioning. Videos are prepared for different audiences including, children, parents, and public health professionals. More > Hand Hygiene ...

  20. DESIGN AND CONSTRUCTION OF A HYDRAULIC PISTON

    OpenAIRE

    Santos De La Cruz, Eulogio; Universidad Nacional Mayor de San Marcos; Rojas Lazo, Oswaldo; Universidad Nacional Mayor de San Marcos; Yenque Dedios, Julio; Universidad Nacional Mayor de San Marcos; Lavado Soto, Aurelio; Universidad Nacional Mayor de San Marcos

    2014-01-01

    A hydraulic system project includes the design, materials selection and construction of the hydraulic piston, hydraulic circuit and the joint with the pump and its accesories. This equiment will be driven by the force of moving fluid, whose application is in the devices of machines, tools, printing, perforation, packing and others. El proyecto de un sistema hidráulico, comprende el diseño, selección de materiales y construcción del pistón hidráulico, circuito hidráulico y el ensamble con l...

  1. Bubble visualization in a simulated hydraulic jump

    CERN Document Server

    Witt, Adam; Shen, Lian

    2013-01-01

    This is a fluid dynamics video of two- and three-dimensional computational fluid dynamics simulations carried out at St. Anthony Falls Laboratory. A transient hydraulic jump is simulated using OpenFOAM, an open source numerical solver. A Volume of Fluid numerical method is employed with a realizable k-epsilon turbulence model. The goal of this research is to model the void fraction and bubble size in a transient hydraulic jump. This fluid dynamics video depicts the air entrainment characteristics and bubble behavior within a hydraulic jump of Froude number 4.82.

  2. Compact Dexterous Robotic Hand

    Science.gov (United States)

    Lovchik, Christopher Scott (Inventor); Diftler, Myron A. (Inventor)

    2001-01-01

    A compact robotic hand includes a palm housing, a wrist section, and a forearm section. The palm housing supports a plurality of fingers and one or more movable palm members that cooperate with the fingers to grasp and/or release an object. Each flexible finger comprises a plurality of hingedly connected segments, including a proximal segment pivotally connected to the palm housing. The proximal finger segment includes at least one groove defining first and second cam surfaces for engagement with a cable. A plurality of lead screw assemblies each carried by the palm housing are supplied with power from a flexible shaft rotated by an actuator and output linear motion to a cable move a finger. The cable is secured within a respective groove and enables each finger to move between an opened and closed position. A decoupling assembly pivotally connected to a proximal finger segment enables a cable connected thereto to control movement of an intermediate and distal finger segment independent of movement of the proximal finger segment. The dexterous robotic hand closely resembles the function of a human hand yet is light weight and capable of grasping both heavy and light objects with a high degree of precision.

  3. Hydraulic Fracturing and the Environment

    Science.gov (United States)

    Ayatollahy Tafti, T.; Aminzadeh, F.; Jafarpour, B.; de Barros, F.

    2013-12-01

    In this presentation, we highlight two key environmental concerns of hydraulic fracturing (HF), namely induced seismicity and groundwater contamination (GC). We examine the induced seismicity (IS) associated with different subsurface fluid injection and production (SFIP) operations and the key operational parameters of SFIP impacting it. In addition we review the key potential sources for possible water contamination. Both in the case of IS and GC we propose modeling and data analysis methods to quantify the risk factors to be used for monitoring and risk reduction. SFIP include presents a risk in hydraulic fracturing, waste water injection, enhanced oil recovery as well as geothermal energy operations. Although a recent report (NRC 2012) documents that HF is not responsible for most of the induced seismicities, we primarily focus on HF here. We look into vaious operational parameters such as volume and rate of water injection, the direction of the well versus the natural fracture network, the depth of the target and the local stress field and fault system, as well as other geological features. The latter would determine the potential for triggering tectonic related events by small induced seismicity events. We provide the building blocks for IS risk assessment and monitoring. The system we propose will involve adequate layers of complexity based on mapped seismic attributes as well as results from ANN and probabilistic predictive modeling workflows. This leads to a set of guidelines which further defines 'safe operating conditions' and 'safe operating zones' which will be a valuable reference for future SFIP operations. We also illustrate how HF can lead to groundwater aquifer contamination. The source of aquifer contamination can be the hydrocarbon gas or the chemicals used in the injected liquid in the formation. We explore possible pathways of contamination within and discuss the likelihood of contamination from each source. Many of the chemical compounds used

  4. [Costs of hand emergencies].

    Science.gov (United States)

    Raimbeau, G

    2003-10-01

    In France at the present time, there is no comprehensive registry of hand injuries. Three types of occurrences; motor vehicle accidents, work accidents, and accidents incident to activities of daily living, are covered by different types of insurance. It is the individual insurance companies, payers of the indemnification, who maintain registries of these accidents. Statistics on work accidents are very detailed and consistent, but they are oriented toward risk management. The aggregate cost of traumatic injuries to the hand is not known. Only large financial institutions are equipped to determine appropriate preventive measures and to establish premium rates based on loss experience. In 2001, hand injuries accounted for 27% of work accidents causing loss of work of at least 1 day. About 29.8% of these work accidents caused permanent partial impairment. About 17.7% of total days lost and 18.2% of the total costs of permanent impairment were due to hand injuries. In the system of compensation for work accidents, there is a major difference in the cost according to the severity of the impairment. If the permanent impairment is equal to or less than 9%, a lump sum payment is made, but if the permanent impairment is over 9%, the worker receives regular payments for the rest of his life. In 2000, the average cost of a work injury with partial permanent impairment of over 9% was [symbol: see text] 85,405, while the average cost of a lump sum settlement was only [symbol: see text] 1479, a ratio of 57 to 1. The compensation costs represent 80% of the cost of work accidents, while the cost of treatment, including all providers and institutions, makes up only 20% of the cost. Compensation for sequelae of accidents in the course of daily life is new for the insurance companies, although these accidents are frequent and often cause significant repercussions in the professional lives of victims because of the loss of hand function. Provision of optimal treatment for these

  5. Study on Characteristics of Hydraulic Servo System for Force Control of Hydraulic Robots

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyo-gon; Han, Changsoo [Hanyang University, Seoul (Korea, Republic of); Lee, Jong-won [Korea University of Science and Technology, Seoul (Korea, Republic of); Park, Sangdeok [Korea Institute of Industrial Technology, Seoul (Korea, Republic of)

    2015-02-15

    Because a hydraulic actuator has high power and force densities, this allows the weight of the robot's limbs to be reduced. This allows for good dynamic characteristics and high energy efficiency. Thus, hydraulic actuators are used in some exoskeleton robots and quadrupedal robots that require high torque. Force control is useful for robot compliance with a user or environment. However, force control of a hydraulic robot is difficult because a hydraulic servo system is highly nonlinear from a control perspective. In this study, a nonlinear model was used to develop a simulation program for a hydraulic servo system consisting of a servo valve, transmission lines, and a cylinder. The problems and considerations with regard to the force control performance for a hydraulic servo system were investigated. A force control method using the nonlinear model was proposed, and its effect was evaluated with the simulation program.

  6. Performance Comparison Between FEDERICA Hand and LARM Hand

    Directory of Open Access Journals (Sweden)

    Giuseppe Carbone

    2015-07-01

    Full Text Available This paper describes two robotic hands that have been developed at University Federico II of Naples and at the University of Cassino. FEDERICA Hand and LARM Hand are described in terms of design and operational features. In particular, careful attention is paid to the differences between the above-mentioned hands in terms of transmission systems. FEDERICA Hand uses tendons and pulleys to drive phalanxes, while LARM Hand uses cross four-bar linkages. Results of experimental tests are reported to show how key design issues affect each robotic hand’s performance.

  7. Parker Hybrid Hydraulic Drivetrain Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Collett, Raymond [Parker-Hannifin Corporation, Cleveland, OH (United States); Howland, James [Parker-Hannifin Corporation, Cleveland, OH (United States); Venkiteswaran, Prasad [National Energy Technology Lab. (NETL), Morgantown, WV (United States)

    2014-03-31

    This report examines the benefits of Parker Hannifin hydraulic hybrid brake energy recovery systems used in commercial applications for vocational purposes. A detailed background on the problem statement being addressed as well as the solution set specific for parcel delivery will be provided. Objectives of the demonstration performed in high start & stop applications included opportunities in fuel usage reduction, emissions reduction, vehicle productivity, and vehicle maintenance. Completed findings during the demonstration period and parallel investigations with NREL, CALSTART, along with a literature review will be provided herein on this research area. Lastly, results identified in the study by third parties validated the savings potential in fuel reduction of on average of 19% to 52% over the baseline in terms of mpg (Lammert, 2014, p11), Parker data for parcel delivery vehicles in the field parallels this at a range of 35% - 50%, emissions reduction of 17.4% lower CO2 per mile and 30.4% lower NOx per mile (Gallo, 2014, p15), with maintenance improvement in the areas of brake and starter replacement, while leaving room for further study in the area of productivity in terms of specific metrics that can be applied and studied.

  8. Thermal hydraulics development for CASL

    Energy Technology Data Exchange (ETDEWEB)

    Lowrie, Robert B [Los Alamos National Laboratory

    2010-12-07

    This talk will describe the technical direction of the Thermal-Hydraulics (T-H) Project within the Consortium for Advanced Simulation of Light Water Reactors (CASL) Department of Energy Innovation Hub. CASL is focused on developing a 'virtual reactor', that will simulate the physical processes that occur within a light-water reactor. These simulations will address several challenge problems, defined by laboratory, university, and industrial partners that make up CASL. CASL's T-H efforts are encompassed in two sub-projects: (1) Computational Fluid Dynamics (CFD), (2) Interface Treatment Methods (ITM). The CFD subproject will develop non-proprietary, scalable, verified and validated macroscale CFD simulation tools. These tools typically require closures for their turbulence and boiling models, which will be provided by the ITM sub-project, via experiments and microscale (such as DNS) simulation results. The near-term milestones and longer term plans of these two sub-projects will be discussed.

  9. Correlações entre força de preensão manual e variáveis antropométricas da mão de jovens adultos Correlations between grip strength and anthropometric variables of young adults'hand

    Directory of Open Access Journals (Sweden)

    Luciane Fernanda Rodrigues Martinho Fernandes

    2011-06-01

    measure for circumference measures. Grip strength measures were performed by means of a Jamar® hydraulic dynamometer. Anthropometric values were correlated with strength measures in the five positions of the opening. Both men and women had greater strength in the right hand. Regarding the positions, the bigger strength of men was in the number 3 (45.5±15.53 kgf and that of women in position 2 (25.5±6.28 kgf. Significant correlations were verified among strength and anthropometric values in the hand width measure and palm circumference - that represent the greater transversal measure and the greater throphism of left hand, respectively, in men's group -, and the finger length measure, that represents the greater longitudinal measure in women's group. Thus, it may be concluded that for men the greater strength is related to the greater transversal measure and to the greater throphism of hand, while for women, it is related to the greater longitudinal length of hand.

  10. Transputer Control of Hydraulic Actuators and Robots

    DEFF Research Database (Denmark)

    Conrad, Finn

    1996-01-01

    Results from a Danish mechatronics research program entitled IMCIA - Intelligent Control and Intelligent Actuators. The objective is development of intelligent actuators for intelligent motion control. A mechatronics test facility with a transputer controlled hydraulic robot suiteable for real...

  11. Concept Evaluation for Hydraulic Yaw System

    DEFF Research Database (Denmark)

    Stubkier, Søren; Pedersen, Henrik C.; Andersen, Torben Ole

    2013-01-01

    a suspension system on a car, leading the loads away from the turbine structure. However, to realize a soft hydraulic yaw system a new design concept must be found. As a part of the development of the new concept a preliminary concept evaluation has been conducted, evaluating seven different hydraulic yaw...... concepts, ranging from a one-to-one copy of the electrical drive (electrical drives replaced by hydraulic dittos), to floating suspension systems mounted on hydraulic cylinders. Rough calculations of size and consequences of the different systems are presented ending up with the final concept for further...... investigation. Loads and yaw demands are based on the IEC 61400-1 standard for wind turbine design, and the loads for this examination are extrapolated from the HAWC2 aeroelastic design code. The concepts are based on a 5 MW off-shore turbine....

  12. HYDRAULICS, Des Moines COUNTY, IOWA, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulic data include spatial datasets and data tables necessary for documenting the hydrologic procedures for estimating flood discharges for a flood insurance...

  13. ON THE THEORIES OF HYDRAULIC GEOMETRY

    Institute of Scientific and Technical Information of China (English)

    Vijay P. SINGH

    2003-01-01

    Hydraulic geometry is of fundamental importance in planning, design, and management of river engineering and training works. Although some concepts of hydraulic geometry were proposed toward the end of the nineteenth century, the real impetus toward formulating a theory of hydraulic geometry was provided by the work of Leopold and Maddock (1953). A number of theories have since been proposed.Some of the theories are interrelated but others are based on quite different principles. All theories,however, assume that the river flow is steady and uniform and the river tends to attain a state of equilibrium or quasi-equilibrium. The differences are due to the differences in hydraulic mechanisms that the theories employ to explain the attainment of equilibrium by the river.

  14. Stream restoration hydraulic design course: lecture notes

    National Research Council Canada - National Science Library

    Newbury, R

    2002-01-01

    Steam restoration encompasses a broad range of activities and disciplines. This lecture series is designed for practitioners who must fit habitat improvement works in the hydraulics of degraded channels...

  15. Drawing a pictogram operator - hydraulic stowing assembly

    Energy Technology Data Exchange (ETDEWEB)

    Bukhgol' ts, V.P.; Dinershtein, V.A.

    1984-11-01

    Hydraulic stowing is widely used during the extraction of coal from seams prone to spontaneous ignition or from seams situated under preserved structures. Experience has shown that the presence of a considerable number of controlling and measuring devices on hydraulic stowing assemblies results in erratic operations. The authors, after examining the controls of the hydraulic stowing complexes, recommend that all functions which the operator might perform badly or not at all should be controlled automatically. The operator must, however, have access to manual controls which should be included in the system in order to achieve an effective and trouble free operation. The authors propose a pictogram to explain the relationship between the human operator and the hydraulic complex, based on structural diagrams. The system developed, which was tried out at the Koksovaya mine, increased the efficiency of the complex and reduced the work load of the operator. 3 references.

  16. HYDRAULICS, Des Moines COUNTY, IOWA, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulic data include spatial datasets and data tables necessary for documenting the hydrologic procedures for estimating flood discharges for a flood insurance...

  17. Hydraulic fracturing chemicals and fluids technology

    CERN Document Server

    Fink, Johannes

    2013-01-01

    When classifying fracturing fluids and their additives, it is important that production, operation, and completion engineers understand which chemical should be utilized in different well environments. A user's guide to the many chemicals and chemical additives used in hydraulic fracturing operations, Hydraulic Fracturing Chemicals and Fluids Technology provides an easy-to-use manual to create fluid formulations that will meet project-specific needs while protecting the environment and the life of the well. Fink creates a concise and comprehensive reference that enables the engineer to logically select and use the appropriate chemicals on any hydraulic fracturing job. The first book devoted entirely to hydraulic fracturing chemicals, Fink eliminates the guesswork so the engineer can select the best chemicals needed on the job while providing the best protection for the well, workers and environment. Pinpoints the specific compounds used in any given fracturing operation Provides a systematic approach to class...

  18. Transputer Control of Hydraulic Actuators and Robots

    DEFF Research Database (Denmark)

    Conrad, Finn

    1996-01-01

    Results from a Danish mechatronics research program entitled IMCIA - Intelligent Control and Intelligent Actuators. The objective is development of intelligent actuators for intelligent motion control. A mechatronics test facility with a transputer controlled hydraulic robot suiteable for real...

  19. 46 CFR 112.50-3 - Hydraulic starting.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hydraulic starting. 112.50-3 Section 112.50-3 Shipping... POWER SYSTEMS Emergency Diesel and Gas Turbine Engine Driven Generator Sets § 112.50-3 Hydraulic starting. A hydraulic starting system must meet the following: (a) The hydraulic starting system must be...

  20. 21 CFR 870.2780 - Hydraulic, pneumatic, or photoelectric plethysmographs.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hydraulic, pneumatic, or photoelectric... § 870.2780 Hydraulic, pneumatic, or photoelectric plethysmographs. (a) Identification. A hydraulic... using hydraulic, pneumatic, or photoelectric measurement techniques. (b) Classification. Class...

  1. Back to basics: hand hygiene and surgical hand antisepsis.

    Science.gov (United States)

    Spruce, Lisa

    2013-11-01

    Health care-associated infections (HAIs) are a significant issue in the United States and throughout the world, but following proper hand hygiene practices is the most effective and least expensive way to prevent HAIs. Hand hygiene is inexpensive and protects patients and health care personnel alike. The four general types of hand hygiene that should be performed in the perioperative environment are washing hands that are visibly soiled, hand hygiene using alcohol-based products, surgical hand scrubs, and surgical hand scrubs using an alcohol-based surgical hand rub product. Barriers to proper hand hygiene may include not thinking about it, forgetting, skin irritation, a lack of role models, or a lack of a safety culture. One strategy for improving hand hygiene practices is monitoring hand hygiene as part of a quality improvement project, but the most important aspect for perioperative team members is to set an example for other team members by following proper hand hygiene practices and reminding each other to perform hand hygiene.

  2. RESEARCH OF THE DYNAMIC CHARACTERISTICS ON A NEW HYDRAULIC SYSTEM OF ELECTRO-HYDRAULIC HAMMER

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A new typed hydraulic system of electro-hydraulic hammer is researched and developed.By means of power bond graphs the modeling and simulation to the dynamic characteristics of the new hydraulic system are performed. The experimental research which is emphasized on the blowing stroke is also performed. It is proved from the result of simulation and experiment that this new hydraulic system possesses such advantages as simplification of structure,flexibleness of operation and reliability of working. Especially it possesses better dynamic characteristics.

  3. Design of a laboratory hydraulic device for testing of hydraulic pumps

    Directory of Open Access Journals (Sweden)

    Pavel Máchal

    2013-01-01

    Full Text Available The present contribution deals with solves problem of research of testing device to monitor of hydrostatic pumps durability about dynamic loading under laboratory conditions. When carrying out the design of testing device are based on load characteristics of tractor hydraulic circuit, the individual characteristics of hydraulic components and performed calculations. Load characteristics on the tractors CASE IH Magnum 310, JOHN DEERE 8100, ZETOR FORTERRA 114 41 and Fendt 926 Vario were measured. Design of a hydraulic laboratory device is based on the need for testing new types of hydraulic pumps or various types of hydraulic fluids. When creating of hydraulic device we focused on testing hydraulic pumps used in agricultural and forestry tractors. Proportional pressure control valve is an active member of the hydraulic device, which provides change of a continuous control signal into relative pressure of operating fluid. The advantage of a designed hydraulic system is possibility of simulation of dynamic operating loading, which is obtained by measurement under real conditions, and thereby creates laboratory conditions as close to real conditions as possible. The laboratory device is constructed at the Department of Transport and Handling, Faculty of Engineering, Slovak University of Agriculture in Nitra.

  4. Characterization of a hydraulically induced bedrock fracture

    OpenAIRE

    2014-01-01

    Hydraulic fracturing is a controversial practice because of concerns about environmental impacts due to its widespread use in recovering unconventional petroleum and natural gas deposits. However, water-only hydraulic fracturing has been used safely and successfully for many years to increase the permeability of aquifers used for drinking and irrigation water supply. This process extends and widens existing bedrock fractures, allowing groundwater storage to increase. Researchers have studied ...

  5. FEEDBACK LINEARISATION APPLIED ON A HYDRAULIC

    DEFF Research Database (Denmark)

    Andersen, Torben Ole; Hansen, Michael Rygaard; Pedersen, Henrik C.;

    2005-01-01

    Generally most hydraulic systems are intrensically non-linear, why applying linear control techniques typically results in conservatively dimensioned controllers to obtain stable performance. Non-linear control techniques have the potential of overcoming these problems, and in this paper the focus...... is on developing and applying several different feedback linearisation (FL) controllers to the individual servo actuators in a hydraulically driven servo robot to evaluate and compare their possiblities and limitations. This is done based on both simulation and experimental results....

  6. Data Analytics of Hydraulic Fracturing Data

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jovan Yang [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Viswanathan, Hari [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hyman, Jeffery [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Middleton, Richard [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-08-11

    These are a set of slides on the data analytics of hydraulic fracturing data. The conclusions from this research are the following: they proposed a permeability evolution as a new mechanism to explain hydraulic fracturing trends; they created a model to include this mechanism and it showed promising results; the paper from this research is ready for submission; they devised a way to identify and sort refractures in order to study their effects, and this paper is currently being written.

  7. Management of Hand Burns

    Directory of Open Access Journals (Sweden)

    Fatih Irmak

    2017-09-01

    Full Text Available Objective: The hand is one of the most frequently affected body parts by burn injuries with a rate of 80% among all burn wounds. Early and effective treatment ensures the best chance of survival as well as a good functional prognosis. The aim of this study was to determine the epidemiology, variation, relationship between etiology and hospital stay, clinical features, and management of hand burns. Material and Methods: This retrospective study was conducted the University of Health Sciences; Şişli Hamidiye Etfal Application and Research Center, Departmant of Plastic, Reconstructive and Aesthetic Surgery and the Intensive Burn Care Unit between April 2009 and April 2014. Burns were assessed based on etiology, anatomical location, percentage of total body surface area affected, and depth of injury. Treatment was categorized as conservative, elective operative, or urgent operative. Results: In the study period, 788 patients were admitted to our Burn Unit. Of these, 240 were females (30.5% and 548 were males (69.5%. The most common type of burn injury in this study was thermal injury (695 cases; 88.2%, followed by electrical injury (67 cases; 8.5%, and chemical, frictional or unknown injuries (26 cases; 3.3%. Majority (more than 85% of the patients had second-degree burns, and some had third-degree burns. Conclusions: Burns commonly affect the hands, and many functional problems may develop if appropriate basic treatments are neglected. The best treatment for burns is prevention. Appropriate indoor arrangement and simple but effective measures that can be taken at home can significantly reduce burn trauma exposure.

  8. Hand grip strength

    DEFF Research Database (Denmark)

    Frederiksen, Henrik; Gaist, David; Petersen, Hans Christian

    2002-01-01

    in life is a major problem in terms of prevalence, morbidity, functional limitations, and quality of life. It is therefore of interest to find a phenotype reflecting physical functioning which has a relatively high heritability and which can be measured in large samples. Hand grip strength is known......-55%). A powerful design to detect genes associated with a phenotype is obtained using the extreme discordant and concordant sib pairs, of whom 28 and 77 dizygotic twin pairs, respectively, were found in this study. Hence grip strength is a suitable phenotype for identifying genetic variants of importance to mid...

  9. Cinematic Motion by Hand

    DEFF Research Database (Denmark)

    Graca, Marina Estela

    2006-01-01

    if we could ascertain a specific ontology for animation within technology that would explain how its marginality is rooted to its essence at least in one of its forms? In this paper I will try to argue that, by overwhelming the cinematic technical standard workings with their hand, authors exposed its...... functional scheme to contingency, thus opening the production process to new unpredictable expressive and communicative possibilities. I will attempt to explain how this corresponds to a renewed way of comprehending technology by, simultaneously, revealing the human reality it contains and physiologically...

  10. Hydraulic Motor Driving Variable-Pitch System for Wind Turbine

    Directory of Open Access Journals (Sweden)

    Ye HUANG

    2013-11-01

    Full Text Available The present hydraulic variable-pitch mechanism of wind turbine uses three hydraulic cylinders to drive three crank and connecting rod mechanisms respectively; the blades are moved with the cranks. The hydraulic variable-pitch mechanism has complex structure, occupies a lot of space and its maintenance is trouble. In order to make up for the shortcomings of hydraulic cylinder variable-pitch system, the present hydraulic variable-pitch mechanism should be changed as follows: hydraulic motors are used to drive gears; gears drive blades; the electro-hydraulic proportional valves are used to control hydraulic motors. The hydraulic control part and electrical control part of variable-pitch system is redesigned. The new variable-pitch system is called hydraulic motor driving variable-pitch system. The new variable-pitch system meets the control requirements of blade pitch, makes the structure simple and its application effect is perfect.    

  11. Hand preference, performance abilities and hand selection in children

    Directory of Open Access Journals (Sweden)

    Sara Marie Scharoun

    2014-02-01

    Full Text Available It is widely know that the pattern of human handedness is such that approximately 90% of the population is right handed with the remainder being left handed, at least in the adult population. What is less well understood is how handedness develops and at what age adult-like handedness patterns emerge. Quantified in terms of both preference and performance, a plethora of different behavioural assessments are currently in use with both children and adults. Handedness questionnaires are commonly used; however, these possess inherent limitations, considering their subjective nature. Hand performance measures have also been implemented; however, such tasks appear to measure different components of handedness. In addition to these traditional measures, handedness has been successfully assessed through observation of hand selection in reaching, which has proven to be a unique and effective manner in understanding the development of handedness in children. Research over the past several decades has demonstrated that young children display weak, inconsistent hand preference tendencies and are slower with both hands. Performance differences between the hands are larger for young children, and consistency improves with age. However, there remains some controversy surrounding the age at which hand preference and hand performance abilities can be considered fully developed. The following paper will provide a review of the literature pertaining to hand preference, performance abilities and hand selection in children in an attempt to ascertain the age at which adult-like patterns of hand preference and performance emerge.

  12. Exposures related to hand eczema

    DEFF Research Database (Denmark)

    Ibler, K.S.; Jemec, G.B.E.; Agner, T.

    2012-01-01

    between exposures (domestic and at work) and prevalence and severity of hand eczema. Methods. Self-administered questionnaires were sent to 3181 healthcare workers in Denmark. Results. Two thousand two hundred and sixty-nine (71%) workers responded to the questionnaire. Frequent hand washing....... Conclusions. Although healthcare workers are recommended to use disinfectants when the hands are not visibly dirty, hand washing is still significantly related to hand eczema. Frequent hand washing may be a question of behavioural habits, and a focus for future guidance should be on changing hand washing......Background. Hand eczema is common in healthcare workers, owing to intensive exposure to wet work and skin irritants. Targeted interventions and vocational guidance based on documented exposures and risk factors are needed. Objectives. The aims of the study were to investigate the relationship...

  13. Handwashing: Clean Hands Save Lives

    Science.gov (United States)

    ... traveling, or already sick, find out how good hand hygiene can protect you, your family, and others. More… ... creating a handwashing campaign for your school community. Hand Hygiene in Healthcare Settings Resources for healthcare workers and ...

  14. Surgical anatomy of hand allotransplantation.

    Science.gov (United States)

    Carlsen, Brian T; Al-Mufarrej, Faisal; Moran, Steven L

    2013-07-01

    The hand is the most refined anatomical terminal device known and the leading edge of the sensorium. Further, the hand is second only to the face in terms of visibility and is a vitally important aspect aesthetic and body image. Hand amputation represents a devastating loss of function and independence. Restoring function after limb loss is a challenge and traditionally includes autologous methods and prosthetics. In the last 15 years, hand transplantation has become a viable option for select patients.

  15. A Hydraulic Tomographic Approach: Coupling of Travel Time and Amplitude Inversion Using Multivariate Statistics

    Science.gov (United States)

    Brauchler, R.; Cheng, J.; Dietrich, P.; Everett, M.; Johnson, B.; Sauter, M.

    2005-12-01

    Knowledge about the spatial variations in hydraulic properties plays an important role controlling solute movement in saturated flow systems. Traditional hydrogeological approaches appear to have difficulties providing high resolution parameter estimates. Thus, we have decided to develop an approach coupling the two existing hydraulic tomographic approaches: a) Inversion of the drawdown as a function of time (amplitude inversion) and b) the inversion of travel times of the pressure disturbance. The advantages of hydraulic travel time tomography are its high structural resolution and computational efficiency. However, travel times are primarily controlled by the aquifer diffusivity making it difficult to determine hydraulically conductivity and storage. Amplitude inversion on the other hand is able to determine hydraulic conductivity and storage separately, but the heavy computational burden of the amplitude inversion is often a shortcoming, especially for larger data sets. Our coupled inversion approach was developed and tested using synthetic data sets. The data base of the inversion comprises simulated slug tests, in which the position of the sources (injection ports) isolated with packers, are varied between the tests. The first step was the inversion of several characteristic travel times (e.g. early, intermediate and late travel times) in order to determine the diffusivity distribution. Secondly, the resulting diffusivity distributions were classified into homogeneous groups in order to differentiate between hydrogeological units characterized by a significant diffusivity contrast. The classification was performed by using multivariate statistics. With a numerical flow model and an automatic parameter estimator the amplitude inversion was performed in a final step. The classified diffusivity distribution is an excellent starting model for the amplitude inversion and allows to reduce strongly the calculation time. The final amplitude inversion overcomes

  16. Hydraulic Conductivity Anisotropy of Heterogeneous Unsaturated Soils

    Science.gov (United States)

    Sun, Dongmin; Zhu, Jianting

    2010-05-01

    The effects of saturation degree (or capillary pressure) on hydraulic conductivity anisotropy in unsaturated soils have not been fully understood. This study developed an approach based on a conceptualization of combining the neural network based pedo-transfer function (PTF) results with the thin layer concept to explore the capillary pressure-dependent anisotropy in relation to soil texture and soil bulk density. The main objective is to examine how anisotropy characteristics are related to the relationships between hydraulic parameters and the basic soil attributes such as texture and bulk density. The hydraulic parameters are correlated with the texture and bulk density based on the pedo-transfer function (PTF) results. It is demonstrated that non-monotonic behavior of the unsaturated soil anisotropy in relation to the capillary pressure is only observed when the saturated hydraulic conductivity and the shape parameter are both related to the mean particle diameter. When only one hydraulic parameter is related to the grain diameter or when both are not related to the same attribute simultaneously, the unsaturated soil anisotropy increases monotonically with the increasing capillary pressure head. Therefore, it is suggested that this behavior is mainly due to the coupled dependence of the layer saturated hydraulic conductivities and the shape factors on the texture and bulk density. The correlation between the soil grain diameter and bulk density decreases the anisotropy effects of the unsaturated layered soils. The study illustrates that the inter-relationships of soil texture, bulk density, and hydraulic properties may cause vastly different characteristics of anisotropic unsaturated soils.

  17. [Hand injuries management of care and hand prevention networks].

    Science.gov (United States)

    Couturier, Christian

    2013-11-01

    Injuries of the hand are common and sometimes more serious than it appears on a non-specialist initial examination. They are a public health issue with some major impact on the continued activity of patients who have been victims of those injuries. The European Federation of Hand Emergency Services (FESUM) accredits SOS Hand centers, dedicated hand trauma organizations in which the specialized medical cares is optima, avoiding the loss of chance to inadequate primary orientation. If nevertheless a serious injury leaves a debilitating sequela Hand Prevention networks, organized by practitioners of SOS Hand centers, help patients establish a process of socio-professional rehabilitation as soon as possible. These networks organize primary, secondary and tertiary prevention of hand trauma and disabilities that can accompany them. Innovative organizations, they resemble a national association that supports the development of new structures. They are open to all professionals of health and their patients, members or not of the network.

  18. The Importance of Hand Washing

    Institute of Scientific and Technical Information of China (English)

    杨昌寿

    2004-01-01

    Medical experts say the most effective way to prevent the spread of diseases is for people to wash their hands with soap and water. The Word Bank and the United Nations carried out a study to urge hand washing around the world. They say programmes to increase hand washing with

  19. Management of Atopic Hand Dermatitis

    DEFF Research Database (Denmark)

    Halling-Overgaard, Anne-Sofie; Zachariae, Claus; Thyssen, Jacob P

    2017-01-01

    This article provides an overview of clinical aspects of hand eczema in patients with atopic dermatitis. Hand eczema can be a part of atopic dermatitis itself or a comorbidity, for example, as irritant or allergic contact dermatitis. When managing hand eczema, it is important to first categorize...

  20. Gravitons that shake hands

    CERN Document Server

    Gubitosi, Giulia

    2016-01-01

    We examine some of the roots of parity violation for gravitons and uncover a closely related new effect: correlations between right and left handed gravitons. Such correlators have spin 4 if they involve gravitons moving along the same direction, and spin zero for gravitons moving with opposite directions. In the first case, the most immediate implication would be a degree of linear polarization for the tensor vacuum fluctuations, which could be seen by gravity wave detectors sensitive enough to probe the primordial background, its degree of polarization and anisotropies. Looking at the anisotropy of the gravity waves linear polarization we identify the parity respecting and violating components of the effect. The imprint on the CMB temperature and polarization would be more elusive, since it averages to zero in the two-point functions, appearing only in their cosmic variance or in fourth order correlators. In contrast, spin zero correlations would have an effect on the two point function of the CMB temperatu...

  1. Classification of hand eczema

    DEFF Research Database (Denmark)

    Agner, T; Aalto-Korte, K; Andersen, K E;

    2015-01-01

    BACKGROUND: Classification of hand eczema (HE) is mandatory in epidemiological and clinical studies, and also important in clinical work. OBJECTIVES: The aim was to test a recently proposed classification system of HE in clinical practice in a prospective multicentre study. METHODS: Patients were...... HE, protein contact dermatitis/contact urticaria, hyperkeratotic endogenous eczema and vesicular endogenous eczema, respectively. An additional diagnosis was given if symptoms indicated that factors additional to the main diagnosis were of importance for the disease. RESULTS: Four hundred and twenty......%) could not be classified. 38% had one additional diagnosis and 26% had two or more additional diagnoses. Eczema on feet was found in 30% of the patients, statistically significantly more frequently associated with hyperkeratotic and vesicular endogenous eczema. CONCLUSION: We find that the classification...

  2. Second-hand signals

    DEFF Research Database (Denmark)

    Bergenholtz, Carsten

    2014-01-01

    Studies of signaling theory have traditionally focused on the dyadic link between the sender and receiver of the signal. Within a science‐based perspective this framing has led scholars to investigate how patents and publications of firms function as signals. I explore another important type...... of signal of firms, which is based on a formalized common practice of external, academic experts referring to firms in their peer reviewed publications. The findings provide qualitative evidence that helps explain why and how this new type of ‘second‐hand’ signal is created, validated and systematically...... used by various agents in their search for and assessment of products and firms. I conclude by arguing how this second‐hand nature of signals goes beyond a simple dyadic focus on senders and receivers of signals, and thus elucidates the more complex interrelations of the various types of agents...

  3. Effect of hand lotion on the effectiveness of hygienic hand antisepsis: Implications for practicing hand hygiene.

    Science.gov (United States)

    Paula, Helga; Hübner, Nils-Olaf; Assadian, Ojan; Bransmöller, Katja; Baguhl, Romy; Löffler, Harald; Kramer, Axel

    2017-08-01

    Skin protection products should be used after washing hands with soap, during breaks, after work, and during leisure time. Aside from their beneficial effects, skin care products may also interact with alcohol-based hand disinfectants by reducing their efficacy. The aim of this study was to investigate the effect of a hand lotion on the effectiveness of hygienic hand antisepsis using an alcohol-based handrub. The effect of a protective hand lotion against an isopropyl alcohol-based handrub was investigated in 20 healthy volunteers according to the European standard test procedure EN 1500 in the following combinations: handwashing and application of hand lotion, only application of hand lotion, and no washing and no hand lotion (control), each for 5 minutes or 1 hour before hand antisepsis. The difference in microbiologic before-and-after values were expressed as log reduction factor. The effectiveness of hand antisepsis was not significantly affected in any of the groups using the tested hand lotion. Hand antisepsis may be delayed for 5 minutes after hand lotion application. Shorter time intervals might be possible but were not tested. Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

  4. Thermal-hydraulic modeling and analysis of hydraulic system by pseudo-bond graph

    Institute of Scientific and Technical Information of China (English)

    胡均平; 李科军

    2015-01-01

    To increase the efficiency and reliability of the thermodynamics analysis of the hydraulic system, the method based on pseudo-bond graph is introduced. According to the working mechanism of hydraulic components, they can be separated into two categories: capacitive components and resistive components. Then, the thermal-hydraulic pseudo-bond graphs of capacitive C element and resistance R element were developed, based on the conservation of mass and energy. Subsequently, the connection rule for the pseudo-bond graph elements and the method to construct the complete thermal-hydraulic system model were proposed. On the basis of heat transfer analysis of a typical hydraulic circuit containing a piston pump, the lumped parameter mathematical model of the system was given. The good agreement between the simulation results and experimental data demonstrates the validity of the modeling method.

  5. Your left-handed brain

    OpenAIRE

    2014-01-01

    While most people prefer to use their right hand to brush their teeth, throw a ball, or hold a tennis racket, left-handers prefer to use their left hand. This is the case for around 10% of all people. There was a time (not so long ago) when left-handers were stigmatized (see Glossary) in Western (and other) communities: it was considered a bad sign if you were left-handed, and left-handed children were often forced to write with their right hand. This is nonsensical: there is nothing wrong wi...

  6. Effect of Natural Fractures on Hydraulic Fracturing

    Science.gov (United States)

    Ben, Y.; Wang, Y.; Shi, G.

    2012-12-01

    Hydraulic Fracturing has been used successfully in the oil and gas industry to enhance oil and gas production in the past few decades. Recent years have seen the great development of tight gas, coal bed methane and shale gas. Natural fractures are believed to play an important role in the hydraulic fracturing of such formations. Whether natural fractures can benefit the fracture propagation and enhance final production needs to be studied. Various methods have been used to study the effect of natural fractures on hydraulic fracturing. Discontinuous Deformation Analysis (DDA) is a numerical method which belongs to the family of discrete element methods. In this paper, DDA is coupled with a fluid pipe network model to simulate the pressure response in the formation during hydraulic fracturing. The focus is to study the effect of natural fractures on hydraulic fracturing. In particular, the effect of rock joint properties, joint orientations and rock properties on fracture initiation and propagation will be analyzed. The result shows that DDA is a promising tool to study such complex behavior of rocks. Finally, the advantages of disadvantages of our current model and future research directions will be discussed.

  7. Microbial effect on soil hydraulic properties

    Science.gov (United States)

    Furman, Alex; Rosenzweig, Ravid; Volk, Elazar; Rosenkranz, Hella; Iden, Sascha; Durner, Wolfgang

    2014-05-01

    Although largely ignored, the soil contains large amount of biofilms (attached microbes) that can affect many processes. While biochemical processes are studied, biophysical processes receive only little attention. Biofilms may occupy some of the pore space, and by that affect the soil hydraulic properties. This effect on unsaturated soils, however, was not intensively studied. In this research we directly measure the hydraulic properties, namely the soil's unsaturated hydraulic conductivity function and retention curve, for soils containing real biofilm. To do that we inoculate soil with biofilm-forming bacteria and incubate it with sufficient amounts of nutrient until biofilm is formed. The hydraulic properties of the incubated soil are then measured using several techniques, including multi-step outflow and evaporation method. The longer measurements (evaporation method) are conducted under refrigeration conditions to minimize microbial activity during the experiment. The results show a clear effect of the biofilm, where the biofilm-affected soil (sandy loam in our case) behaves like a much finer soil. This qualitatively makes sense as the biofilm generates an effective pore size distribution that is characterized by smaller pores. However, the effect is much more complex and needs to be studied carefully considering (for example) dual porosity models. We compare our preliminary results with other experiments, including flow-through column experiments and experiments with biofilm analogues. Clearly a better understanding of the way microbial activity alters the hydraulic properties may help designing more efficient bioremediation, irrigation, and other soil-related processes.

  8. Vibration Isolation for Parallel Hydraulic Hybrid Vehicles

    Directory of Open Access Journals (Sweden)

    The M. Nguyen

    2008-01-01

    Full Text Available In recent decades, several types of hybrid vehicles have been developed in order to improve the fuel economy and to reduce the pollution. Hybrid electric vehicles (HEV have shown a significant improvement in fuel efficiency for small and medium-sized passenger vehicles and SUVs. HEV has several limitations when applied to heavy vehicles; one is that larger vehicles demand more power, which requires significantly larger battery capacities. As an alternative solution, hydraulic hybrid technology has been found effective for heavy duty vehicle because of its high power density. The mechanical batteries used in hydraulic hybrid vehicles (HHV can be charged and discharged remarkably faster than chemical batteries. This feature is essential for heavy vehicle hybridization. One of the main problems that should be solved for the successful commercialization of HHV is the excessive noise and vibration involving with the hydraulic systems. This study focuses on using magnetorheological (MR technology to reduce the noise and vibration transmissibility from the hydraulic system to the vehicle body. In order to study the noise and vibration of HHV, a hydraulic hybrid subsystem in parallel design is analyzed. This research shows that the MR elements play an important role in reducing the transmitted noise and vibration to the vehicle body. Additionally, locations and orientations of the isolation system also affect the efficiency of the noise and vibration mitigation. In simulations, a skyhook control algorithm is used to achieve the highest possible effectiveness of the MR isolation system.

  9. Prognostic factors for the recovery of hand function following trapeziectomy with ligamentoplasty stabilisation.

    Science.gov (United States)

    Moineau, G; Richou, J; Liot, M; Le Nen, D

    2009-09-01

    Numerous procedures are in use to treat trapeziometacarpal osteoarthritis. Most of these techniques impair hand function. In a series of trapeziectomies stabilized by ligament reconstruction with tendon suspension, we investigated whether eventual parameters influenced hand function and dexterity. Some parameters influence hand function recovery following trapeziectomy combined to ligamento-tendinous stabilization. This is a continuous, retrospective, single surgeon series; 60 cases of thumb trapeziometacarpal osteoarthritis were treated with trapeziectomy and ligament reconstruction (40 palmaris longus, and 20 half flexor carpi radialis) with no additional metacarpophalangeal (MCP) joint surgery. Besides assessing classical clinical outcome criteria (pain, mobility, force), we analyzed hand function: this was obtained with a questionnaire about different everyday movements. Five types of grip were included in this analysis: spherical, pinch grasp, key pinch, power grip, and precision pinch. Fifty-one trapeziectomies (85%) were evaluated at an average follow-up of 7.5 years (5-11.5). Ninety-four percent of patients had good results for pain. The average Kapandji score for mobility was 9.6 (6-10) with a mean web angle at 36.5 degrees. Hyperextension of the MCP joint occurred in 36 cases and measured an average of 26 degrees (5 degrees-50 degrees). Compared to the contralateral side average strength was 97% with the Jamar dynamometer and 88% for the key pinch. The rate of satisfaction was 96%. Collapse of trapezial height was constant, and at last follow-up, the trapezial index was 50% of its preoperative initial value. The results relative to hand function assessment were good in 58% of patients. The spherical grip was the most difficult to restore. The analysis of the 42% of patients with average or poor hand function showed five prognostic factors for a poor outcome: young age at surgery, persisting postoperative pain, postoperative hyperextension of the MCP joint

  10. On the other hand: dummy hands and peripersonal space.

    Science.gov (United States)

    Makin, Tamar R; Holmes, Nicholas P; Ehrsson, H Henrik

    2008-08-05

    Where are my hands? The brain can answer this question using sensory information arising from vision, proprioception, or touch. Other sources of information about the position of our hands can be derived from multisensory interactions (or potential interactions) with our close environment, such as when we grasp or avoid objects. The pioneering study of multisensory representations of peripersonal space was published in Behavioural Brain Research almost 30 years ago [Rizzolatti G, Scandolara C, Matelli M, Gentilucci M. Afferent properties of periarcuate neurons in macaque monkeys. II. Visual responses. Behav Brain Res 1981;2:147-63]. More recently, neurophysiological, neuroimaging, neuropsychological, and behavioural studies have contributed a wealth of evidence concerning hand-centred representations of objects in peripersonal space. This evidence is examined here in detail. In particular, we focus on the use of artificial dummy hands as powerful instruments to manipulate the brain's representation of hand position, peripersonal space, and of hand ownership. We also review recent studies of the 'rubber hand illusion' and related phenomena, such as the visual capture of touch, and the recalibration of hand position sense, and discuss their findings in the light of research on peripersonal space. Finally, we propose a simple model that situates the 'rubber hand illusion' in the neurophysiological framework of multisensory hand-centred representations of space.

  11. Dissociated small hand muscle atrophy in aging: the 'senile hand' is a split hand.

    NARCIS (Netherlands)

    Voermans, N.C.; Schelhaas, H.J.; Munneke, M.; Zwarts, M.J.

    2006-01-01

    The term 'split hand' refers to a pattern of dissociated atrophy of hand muscles and was first described in ALS. We hypothesize that this phenomenon also occurs in 'normal' aging. We investigated healthy subjects of different ages and found a progressive dissociation in atrophy of the hand muscles,

  12. Hand Spring Operated Movement Enhancer (HandSOME): a portable, passive hand exoskeleton for stroke rehabilitation.

    Science.gov (United States)

    Brokaw, Elizabeth B; Black, Iian; Holley, Rahsaan J; Lum, Peter S

    2011-08-01

    Stroke patients often have flexor hypertonia and finger extensor weakness, which makes it difficult to open their affected hand for functional grasp. Because of this impairment, hand rehabilitation after stroke is essential for restoring functional independent lifestyles. The goal of this study is to develop a passive, lightweight, wearable device to assist with hand function during performance of activities of daily living. The device, Hand Spring Operated Movement Enhancer (HandSOME), assists with opening the patient's hand using a series of elastic cords that apply extension torques to the finger joints and compensates for the flexor hypertonia. Device design and calibration are described as well as functional and usability testing with stroke subjects with a wide range of hand impairments. In initial testing with eight stroke subjects with finger flexor hypertonia, use of the HandSOME significantly increased range of motion and functional ability (p=0.002) . There was some decrease in grip strength with the HandSOME device at the subject's ideal setting, however this was not statistically significant (p=0.167) and did not seem to have a significant effect on function. Overall HandSOME shows promise as a training tool to facilitate repetitive task practice for improving hand function in stroke patients. HandSOME can be used as part of a home-based therapy program, or as an orthotic for replacing lost function.

  13. A Computational Model of Hydraulic Volume Displacement Drive

    Directory of Open Access Journals (Sweden)

    V. N. Pil'gunov

    2014-01-01

    Full Text Available The paper offers a computational model of industrial-purpose hydraulic drive with two hydraulic volume adjustable working chamber machines (pump and motor. Adjustable pump equipped with the pressure control unit can be run together with several adjustable hydraulic motors on the principle of three-phase hydraulic socket-outlet with high-pressure lines, drain, and drainage system. The paper considers the pressure-controlled hydrostatic transmission with hydraulic motor as an output link. It shows a possibility to create a saving hydraulic drive using a functional tie between the adjusting parameters of the pump and hydraulic motor through the pressure difference, torque, and angular rate of the hydraulic motor shaft rotation. The programmable logic controller can implement such tie. The Coulomb and viscous frictions are taken into consideration when developing a computational model of the hydraulic volume displacement drive. Discharge balance considers external and internal leakages in equivalent clearances of hydraulic machines, as well as compression loss volume caused by hydraulic fluid compressibility and deformation of pipe walls. To correct dynamic properties of hydraulic drive, the paper offers that in discharge balance are included the additional regulated external leakages in the open circuit of hydraulic drive and regulated internal leakages in the closed-loop circuit. Generalized differential equations having functional multipliers and multilinked nature have been obtained to describe the operation of hydraulic positioning and speed drive with two hydraulic volume adjustable working chamber machines. It is shown that a proposed computational model of hydraulic drive can be taken into consideration in development of LS («Load-Sensing» drives, in which the pumping pressure is tuned to the value required for the most loaded slave motor to overcome the load. Results attained can be used both in designing the industrial-purpose heavy

  14. Robotically enhanced rubber hand illusion.

    Science.gov (United States)

    Arata, Jumpei; Hattori, Masashi; Ichikawa, Shohei; Sakaguchi, Masamichi

    2014-01-01

    The rubber hand illusion is a well-known multisensory illusion. In brief, watching a rubber hand being stroked by a paintbrush while one's own unseen hand is synchronously stroked causes the rubber hand to be attributed to one's own body and to "feel like it's my hand." The rubber hand illusion is thought to be triggered by the synchronized tactile stimulation of both the subject's hand and the fake hand. To extend the conventional rubber hand illusion, we introduce robotic technology in the form of a master-slave telemanipulator. The developed one degree-of-freedom master-slave system consists of an exoskeleton master equipped with an optical encoder that is worn on the subject's index finger and a motor-actuated index finger on the rubber hand, which allows the subject to perform unilateral telemanipulation. The moving rubber hand illusion has been studied by several researchers in the past with mechanically connected rigs between the subject's body and the fake limb. The robotic instruments let us investigate the moving rubber hand illusion with less constraints, thus behaving closer to the classic rubber hand illusion. In addition, the temporal delay between the body and the fake limb can be precisely manipulated. The experimental results revealed that the robotic instruments significantly enhance the rubber hand illusion. The time delay is significantly correlated with the effect of the multisensory illusion, and the effect significantly decreased at time delays over 100 ms. These findings can potentially contribute to the investigations of neural mechanisms in the field of neuroscience and of master-slave systems in the field of robotics.

  15. Development of two-phase pipeline hydraulic analysis model based on Beggs-Brill correlation

    Science.gov (United States)

    Waluyo, Joko; Hermawan, Achilleus; Indarto

    2016-06-01

    The hydraulic analysis is an important stage in a reliable pipeline design. In the implementation, fluid distribution from a source to the sinks often occurs on parallel pipeline networks. The solution to the problem is complicated because of the iterative technique requirement. Regarding its solution effectiveness, there is a need for analysis related to the model and the solution method. This study aims to investigate pipeline hydraulic analysis on distributing of two-phase fluids flow. The model uses Beggs-Brill correlation to converse mass flow rates into pressure drops. In the solution technique, the Newton-Raphson iterative method is utilized. The iterative technique is solved using a computer program. The study is carried out using a certain pipeline network. The model is validated by comparing between Beggs-Brill towards Mukherjee-Brill correlation. The result reveals that the computer program enables solving of iterative calculation on the parallel pipeline hydraulic analysis. Convergence iteration is achieved by 50 iterations. The main results of the model are mass flow rate and pressure drop. The mass flow rate is obtained in the deviation up to 2.06%, between Beggs-Brill and Mukherjee-Brill correlation. On the other hand, the pressure gradient deviation is achieved on a higher deviation due to the different approach of the two correlations. The model can be further developed in the hydraulic pipeline analysis for two-phase flow.

  16. Hydraulic characteristics of sedimentary deposits at the J-PARC proton-accelerator, Japan

    Directory of Open Access Journals (Sweden)

    Marui Atsunao

    2007-12-01

    Full Text Available Hydraulic characteristics of sediments were investigated at J-PARC for the purpose of site characterization in relation with the construction of Japan's largest proton-accelerator. A total of 340 samples extracted from 9 exploratory wells were examined by standard laboratory tests and complemented with statistical analyses to quantitatively determine the main terrain attributes. Two main hydro-geological units were recognized, although a number of embedded layers defined a
    multilevel aquifer. Grain-size distribution derived from sieve analysis and the coefficient of uniformity showed that soils are poorly sorted. On the other hand, hydraulic conductivity was measured by a
    number of parameters such as a log-normal distribution. Conductivity was also predicted by empirical formulas, yielding values up to three orders of magnitude higher. Discrepancies were explained in
    terms of soil anisotropy and intrinsic differences in the calculation methods. Based on the Shepherd's approach, a power relationship between permeability and grain size was found at 2 wells. Hydraulic
    conductivity was also correlated to porosity. However, this  nterdependence was not systematic and therefore, properties at many parts of the profile were considered to be randomly distributed. Finally,
    logs of electrical conductivity suggested that variations of soil hydraulic properties can be associated to changes in water quality. In spite of the remaining uncertainties, results yielded from the study are useful to better understand the numerical modelling of the subsurface system in the site.

  17. Measurement and evaluation of static characteristics of rotary hydraulic motor

    Directory of Open Access Journals (Sweden)

    Hružík Lumír

    2014-03-01

    Full Text Available The paper describes experimental equipment for measurement of static characteristics of rotary hydraulic motor. It is possible to measure flow, pressure, temperature, speed and torque by means of this equipment. It deals with measurement of static characteristics of a gear rotary hydraulic motor. Mineral oil is used as hydraulic liquid in this case. Flow, torque and speed characteristics are evaluated from measured parameters. Measured mechanical-hydraulic, flow and total efficiencies of the rotary hydraulic motor are adduced in the paper. It is possible to diagnose technical conditions of the hydraulic motor (eventually to recommend its exchange from the experimental measurements.

  18. Promoting water hydraulics in Malaysia: A green educational approach

    Science.gov (United States)

    Yusof, Ahmad Anas; Zaili, Zarin Syukri; Hassan, Siti Nor Habibah; Tuan, Tee Boon; Saadun, Mohd Noor Asril; Ibrahim, Mohd Qadafie

    2014-10-01

    In promoting water hydraulics in Malaysia, this paper presents research development of water hydraulics educational training system for secondary and tertiary levels in Malaysia. Water hydraulics trainer with robotic attachment has been studied in order to promote the usefulness of such educational tools in promoting sustainability and green technology in the country. The trainer is being developed in order to allow constructive curriculum development and continuous marketing research for the effectiveness and usefulness of using water in hydraulic power trainer. The research on water-based hydraulic trainer is now possible with the current development in water hydraulics technology.

  19. Hydraulic characterization of hydrothermally altered Nopal tuff

    Energy Technology Data Exchange (ETDEWEB)

    Green, R.T.; Meyer-James, K.A. [Southwest Research Institute, San Antonio, TX (United States); Rice, G. [George Rice and Associates, San Antonio, TX (United States)

    1995-07-01

    Understanding the mechanics of variably saturated flow in fractured-porous media is of fundamental importance to evaluating the isolation performance of the proposed high-level radioactive waste repository for the Yucca Mountain site. Developing that understanding must be founded on the analysis and interpretation of laboratory and field data. This report presents an analysis of the unsaturated hydraulic properties of tuff cores from the Pena Blanca natural analog site in Mexico. The basic intent of the analysis was to examine possible trends and relationships between the hydraulic properties and the degree of hydrothermal alteration exhibited by the tuff samples. These data were used in flow simulations to evaluate the significance of a particular conceptual (composite) model and of distinct hydraulic properties on the rate and nature of water flow.

  20. Simulation of a Hydraulic Pump Control Valve

    Science.gov (United States)

    Molen, G. Vander; Akers, A.

    1987-01-01

    This paper describes the mode of operation of a control valve assembly that is used with a hydraulic pump. The operating system of the valve is modelled in a simplified form, and an analogy for hydraulic resonance of the pressure sensing system is presented. For the control valve investigated, air entrainment, length and diameter of the resonator neck, and valve mass produced the greatest shift in resonant frequency. Experimental work was conducted on the hydraulic system so that the resonance levels and frequencies could be measured and the accuracy of the theory verified. The results obtained make it possible to evaluate what changes to any of the variables considered would be most effective in driving the second harmonic frequency above the operating range.

  1. Soil Structure and Saturated Hydraulic Conductivity

    Science.gov (United States)

    Houskova, B.; Nagy, V.

    The role of soil structure on saturated hydraulic conductivity changes is studied in plough layers of texturally different soils. Three localities in western part of Slovakia in Zitny ostrov (Corn Island) were under investigation: locality Kalinkovo with light Calcaric Fluvisol (FAO 1970), Macov with medium heavy Calcari-mollic Fluvisol and Jurova with heavy Calcari-mollic Fluvisol. Soil structure was determined in dry as well as wet state and in size of macro and micro aggregates. Saturated hydraulic conductivity was measured by the help of double ring method. During the period of ring filling the soil surface was protected against aggregates damage by falling water drops. Spatial and temporal variability of studied parameters was evaluated. Cultivated crops were ensilage maize at medium heavy and heavy soil and colza at light soil. Textural composition of soil and actual water content at the beginning of measurement are one of major factor affecting aggregate stability and consequently also saturated hydraulic conductivity.

  2. Evaluation of the Relationship Between Hand Osteoarthritis and Osteoporosis in Postmenauposal Women

    Directory of Open Access Journals (Sweden)

    Oya Özdemir

    2013-04-01

    Full Text Available Aim: Osteoarthritis (OA and osteoporosis (OP are the two leading causes of disability in elderly. The aim of this study was to compare the values of bone mineral density (BMD in postmenopausal women with and without hand OA. Meterial and Methods: 26 patient with hand OA and 22 age and sex-matched individuals without hand OA were included in the study. The patients with secondary OP and under the treatment of OP were excluded. In physical examination, the number of tender and swollen joints, Heberden and Bouchard nodules were recorded. The participants’ grip and lateral pinch strength were measured using Jamar dynamometer and pinchmeter. The Australian Canadian Osteoarthritis Hand Index (AUSCAN was used to evaluate pain and function. Additionally, the pain during rest and activity were evaluated on a 10-cm visual analog scale (VAS. BMD was measured from 3 different regions (femur neck, lumbar vertebra, and radius using dual energy X-ray absorptiometry. Results: The mean age of the patients’ was 59.0±6.1 years and 84.6% were right-handed. No signi cant difference was found in BMD values of the femur neck, lumbar vertebra between the two groups. However, the patients with hand OA had signi cantly lower t-scores of distal radius (p=0.045. There was no statistically signi cant correlation between distal radius t-score and age, body mass index, postmenopausal duration, right hand pinch strength, number of nodules in the right hand, pain duration, VAS rest and activity scores, AUSCAN pain, stiffness and function scores whereas we found a positive correlation between distal radius t-score and right hand grip strength in the patient group (r=0.478, p=0.016. Conclusion: Several studies investigating the relationship between hand OA and OP found positive correlation whereas some found negative correlation. We found an inverse relationship between hand OA and distal radius t-score. Further studies are needed to enlighten the pathogenesis of

  3. Prosthetic helping hand

    Science.gov (United States)

    Vest, Thomas W. (Inventor); Carden, James R. (Inventor); Norton, William E. (Inventor); Belcher, Jewell G. (Inventor)

    1992-01-01

    A prosthetic device for below-the-elbow amputees, having a C-shaped clamping mechanism for grasping cylindrical objects, is described. The clamping mechanism is pivotally mounted to a cuff that fits on the amputee's lower arm. The present invention is utilized by placing an arm that has been amputated below the elbow into the cuff. The clamping mechanism then serves as a hand whenever it becomes necessary for the amputee to grasp a cylindrical object such as a handle, a bar, a rod, etc. To grasp the cylindrical object, the object is jammed against the opening in the C-shaped spring, causing the spring to open, the object to pass to the center of the spring, and the spring to snap shut behind the object. Various sizes of clamping mechanisms can be provided and easily interchanged to accommodate a variety of diameters. With the extension that pivots and rotates, the clamping mechanism can be used in a variety of orientations. Thus, this invention provides the amputee with a clamping mechanism that can be used to perform a number of tasks.

  4. Digit and hand replantation.

    Science.gov (United States)

    Beris, Alexandros E; Lykissas, Marios G; Korompilias, Anastasios V; Mitsionis, Gregory I; Vekris, Marios D; Kostas-Agnantis, Ioannis P

    2010-09-01

    For the past 45 years, the advent of microsurgery has led to replantation of almost every amputated part such as distal phalanx, finger tip, etc. Replantation of digits and hand can restore not only circulation, but also function and cosmetic of the amputated part. The goals of replantation are to restore circulation and regain sufficient function and sensation of the amputated part. Strict selection criteria are necessary to optimize the functional result. The management of this type of injuries includes meticulous preoperative management, microsurgical experience and continuous postoperative care. Among various factors influencing the outcome, the most important are the type and the level of injury, ischemia time, history of diabetes, age, sex, and smoking history. During the replantation procedure, bone stabilization, tendon repair, arterial anastomoses, venous anastomoses, nerve coaptation, and skin coverage should be performed. All structures should be repaired primarily, unless a large nerve gap or a flexor tendon avulsion injury is present. Adequate postoperative evaluation is mandatory to avoid early or late complications. To improve functional results, many replantation patients may need further reconstructive surgery.

  5. Dynamic Hand Gesture Recognition Using the Skeleton of the Hand

    OpenAIRE

    Vasile Buzuloiu; Patrick Lambert; Didier Coquin; Bogdan Ionescu

    2005-01-01

    This paper discusses the use of the computer vision in the interpretation of human gestures. Hand gestures would be an intuitive and ideal way of exchanging information with other people in a virtual space, guiding some robots to perform certain tasks in a hostile environment, or interacting with computers. Hand gestures can be divided into two main categories: static gestures and dynamic gestures. In this paper, a novel dynamic hand gesture recognition technique is proposed. It is based on ...

  6. Self-potential observations during hydraulic fracturing

    Energy Technology Data Exchange (ETDEWEB)

    Moore, Jeffrey R.; Glaser, Steven D.

    2007-09-13

    The self-potential (SP) response during hydraulic fracturing of intact Sierra granite was investigated in the laboratory. Excellent correlation of pressure drop and SP suggests that the SP response is created primarily by electrokinetic coupling. For low pressures, the variation of SP with pressure drop is linear, indicating a constant coupling coefficient (Cc) of -200 mV/MPa. However for pressure drops >2 MPa, the magnitude of the Cc increases by 80% in an exponential trend. This increasing Cc is related to increasing permeability at high pore pressures caused by dilatancy of micro-cracks, and is explained by a decrease in the hydraulic tortuosity. Resistivity measurements reveal a decrease of 2% prior to hydraulic fracturing and a decrease of {approx}35% after fracturing. An asymmetric spatial SP response created by injectate diffusion into dilatant zones is observed prior to hydraulic fracturing, and in most cases this SP variation revealed the impending crack geometry seconds before failure. At rupture, injectate rushes into the new fracture area where the zeta potential is different than in the rock porosity, and an anomalous SP spike is observed. After fracturing, the spatial SP distribution reveals the direction of fracture propagation. Finally, during tensile cracking in a point load device with no water flow, a SP spike is observed that is caused by contact electrification. However, the time constant of this event is much less than that for transients observed during hydraulic fracturing, suggesting that SP created solely from material fracture does not contribute to the SP response during hydraulic fracturing.

  7. Measurement and modeling of unsaturated hydraulic conductivity

    Science.gov (United States)

    Perkins, Kim S.; Elango, Lakshmanan

    2011-01-01

    The unsaturated zone plays an extremely important hydrologic role that influences water quality and quantity, ecosystem function and health, the connection between atmospheric and terrestrial processes, nutrient cycling, soil development, and natural hazards such as flooding and landslides. Unsaturated hydraulic conductivity is one of the main properties considered to govern flow; however it is very difficult to measure accurately. Knowledge of the highly nonlinear relationship between unsaturated hydraulic conductivity (K) and volumetric water content is required for widely-used models of water flow and solute transport processes in the unsaturated zone. Measurement of unsaturated hydraulic conductivity of sediments is costly and time consuming, therefore use of models that estimate this property from more easily measured bulk-physical properties is common. In hydrologic studies, calculations based on property-transfer models informed by hydraulic property databases are often used in lieu of measured data from the site of interest. Reliance on database-informed predicted values with the use of neural networks has become increasingly common. Hydraulic properties predicted using databases may be adequate in some applications, but not others. This chapter will discuss, by way of examples, various techniques used to measure and model hydraulic conductivity as a function of water content, K. The parameters that describe the K curve obtained by different methods are used directly in Richards’ equation-based numerical models, which have some degree of sensitivity to those parameters. This chapter will explore the complications of using laboratory measured or estimated properties for field scale investigations to shed light on how adequately the processes are represented. Additionally, some more recent concepts for representing unsaturated-zone flow processes will be discussed.

  8. On the Hydraulics of Flowing Horizontal Wells

    Science.gov (United States)

    Bian, A.; Zhan, H.

    2003-12-01

    A flowing horizontal well is a special type of horizontal well that does not have pumping/injecting facility. The discharge rate of a flowing horizontal well is controlled by the hydraulic gradient between the aquifer and the well and it generally varies with time if the hydraulic head of the aquifer is transient. This type of well has been used in landslide control, mining dewatering, water table control, underground water transportation through a horizontal tunnel, agricultural water drainage, and other applications. Flowing horizontal wells have quite different hydrodynamic characteristics from horizontal wells with fixed pumping or injecting rates because their discharge rates are functions of the aquifer hydraulic heads (Zhan et al, 2001; Zhan and Zlotnik, 2002). Hydraulics of flowing horizontal wells have rarely been studied although the hydraulics of flowing vertical wells have been extensively investigated before. The purpose of this paper is to obtain analytical solutions of groundwater flow to a flowing horizontal-well in a confined aquifer, in a water table aquifer without precipitation, and in a water table aquifer with precipitation. The functions of the flowing horizontal well discharge rates versus time will be obtained under above mentioned different aquifer conditions. The relationships of the aquifer hydraulic heads versus the discharge rates of the well will be investigated. The rate of water table decline due to the dewatering of the well will also be computed, and this solution is particularly useful for landslide control and mining dewatering. The theoretical solutions will be compared with results of experiments that will be conducted in the hydrological laboratory at Texas A&M University. Reference: Zhan, H., Wang, L.V., and Park, E, On the horizontal well pumping tests in the anisotropic confined aquifers, J. hydrol., 252, 37-50, 2001. Zhan, H., and Zlotnik, V. A., Groundwater flow to a horizontal or slanted well in an unconfined aquifer

  9. A força de preensão manual é boa preditora do desempenho funcional de idosos frágeis: um estudo correlacional múltiplo The hand-grip forecasts the functional performance of fragile elder subjects: a multiple-correlation study

    Directory of Open Access Journals (Sweden)

    Amandio A.R. Geraldes

    2008-02-01

    Full Text Available A força de preensão manual (FPM associa-se com a funcionalidade de idosos, mas há dúvidas sobre o valor dessa relação em todas as situações. O estudo observou a correlação entre FPM de idosos residentes em instituições de cuidados permanentes (asilos e o desempenho funcional (DF em tarefas específicas e inespecíficas para as mãos. Participaram 12 homens (70±6 anos; 64±9 kg; 160±10 cm e sete mulheres (77±11 anos; 49±10 kg; 147±10 cm. A FPM foi medida com dinamômetro hidráulico. As tarefas motoras propostas foram: caminhar 10 m na velocidade máxima (C10, timed up & go test (TUGT, colocar e retirar chave de fechadura (TCCF e tirar e recolocar lâmpada em um bocal (TCLB. O teste de Wilcoxon revelou que os homens apresentaram melhores desempenhos que as mulheres em todos as medidas, exceto IMC, TCCF e TCLB (pHand-grip strength (HGS has been used to predict functional limitation in the elderly. However, this relationship in all situations is doubtful. The purpose of the study was to observe the association between HGS and functional performance (FP, in specific and not specific tasks among 19 long-term home elderly residents, 12 men (70±6 yrs; 64±9 kg; 160±10 cm and 7 women (77±11 yrs; 49±10 kg; 147±10 cm. HGS was measured by a hydraulic hand dynamometer. The FP was measured by the time to perform the following tasks: 1 habitual gait speed (HGS; 2 timed up & go test (TUGT; 3 opening a lock with a key (OLK; 4 to take off and put in a light bulb (TPB. The Wilcoxon test revealed that men were better than women in all measurements except for the IMC, OLK and TPL (p<0.05. The Spearman coefficients showed significant correlation between HGS and three FP tests: TPL (r=-.54; p=.018; TUGT (r=-.67; p=.002 and HGS (r=-.69; p=.001. The multiple correlation showed good correlation between the HGS and all FP tests (R=.66; R²=.44; p<.04. These results suggest that HGS may be a good predictor for FP, especially for fragile and

  10. Hydraulic permeability of bentonite-polymer composites for application in landfill technology

    Science.gov (United States)

    Dehn, Hanna; Haase, Hanna; Schanz, Tom

    2015-04-01

    Bentonites are often used as barrier materials in landfill technology to prevent infiltration of leachates to the natural environment. Since decades, geoenvironmental engineering aims at improving the hydro-mechanical performance of landfill liners. Various studies on the permeability performance of geosynthetic clay liners (GCLs) show effects of non-standard liquids on behaviour of Na+-bentonite regarding its sealing capacity. With increasing concentration of chemical aggressive solutions the sealing capacity decreases (Shackelford et al. 2000). An opportunity to improve the hydraulic permeability of the bentonites is the addition of polymers. The changes in hydraulic permeability performance of polymer treated and untreated bentonites while adding chemical aggressive solutions were studied by several authors. Results obtained by Scalia et al. (2014) illustrate that an increase in permeability can be prevented by adding polymer to Na+-bentonite. On the other hand, Ashmawy et al. (2002) presented results on the incapability of several commercial bentonite-polymer-products. The objective of this study is to characterize the influence of polymer addition on hydraulic performance of Na+-bentonite systematically. Therefore, the influence of 1% polymer addition of cationic and anionic polyacrylamide on the swelling pressure and hydraulic permeability of MX 80 bentonite was investigated. Preparation of bentonite-polymer composites was conducted (1) in dry conditions and (2) using solution-intercalation method. Experiments on hydraulic permeability were carried out using distilled water as well as CaCl2-solution. References Ashmawy, A. K., El-Hajji, D., Sotelo, N. & Muhammad, N. (2002), `Hydraulic Performance of Untreated and Polymer-treated Bentonite in Inorganic Landfill Leachates', Clays and Clay Minerals 50(5), 546-552. Scalia, J., Benson, C., Bohnhoff, G., Edil, T. & Shackelford, C. (2014), 'Long-Term Hydraulic Conductivity of a Bentonite-Polymer Composite Permeated

  11. Thermal Hydraulic Stability in a Coaxial Thermosyphon

    Institute of Scientific and Technical Information of China (English)

    YANG Jianhui; LU Wenqiang; LI Qing; LI Qiang; ZHOU Yuan

    2005-01-01

    The heat transfer and thermal hydraulic stability in a two-phase thermosyphon with coaxial riser and down-comer has been experimentally investigated and theoretically analyzed to facilitate its application in cold neutron source. The flow in a coaxial thermosyphon was studied experimentally for a variety of heating rates, transfer tube lengths, charge capacities, and area ratios. A numerical analysis of the hydraulic balance between the driving pressure head and the resistance loss has also been performed. The results show that the presented coaxial thermosyphon has dynamic performance advantages relative to natural circulation in a boiling water reactor.

  12. Large-eddy simulation in hydraulics

    CERN Document Server

    Rodi, Wolfgang

    2013-01-01

    Complex turbulence phenomena are of great practical importance in hydraulics, including environmental flows, and require advanced methods for their successful computation. The Large Eddy Simulation (LES), in which the larger-scale turbulent motion is directly resolved and only the small-scale motion is modelled, is particularly suited for complex situations with dominant large-scale structures and unsteadiness. Due to the increasing computer power, LES is generally used more and more in Computational Fluid Dynamics. Also in hydraulics, it offers great potential, especially for near-field probl

  13. Mineral resource of the month: hydraulic cement

    Science.gov (United States)

    van Oss, Hendrik G.

    2012-01-01

    Hydraulic cements are the binders in concrete and most mortars and stuccos. Concrete, particularly the reinforced variety, is the most versatile of all construction materials, and most of the hydraulic cement produced worldwide is portland cement or similar cements that have portland cement as a basis, such as blended cements and masonry cements. Cement typically makes up less than 15 percent of the concrete mix; most of the rest is aggregates. Not counting the weight of reinforcing media, 1 ton of cement will typically yield about 8 tons of concrete.

  14. Hand spring operated movement enhancer (HandSOME) device for hand rehabilitation after stroke.

    Science.gov (United States)

    Brokaw, Elizabeth B; Holley, Rahsaan J; Lum, Peter S

    2010-01-01

    Hand rehabilitation after stroke is essential for restoring functional independent lifestyles. After stroke, patients often have flexor hypertonia, making it difficult to open their hand for functional grasp. The development and initial testing of a passive hand rehabilitation device is discussed. The device, Hand Spring Operated Movement Enhancer (HandSOME), assists with opening the patient's hand using a series of bungee cords that apply extension torques to the finger joints that compensate for the flexor hypertonia. This results in significant increase in range of motion and functional use when wearing HandSOME, even in severely impaired subjects. Device design, calibration, and range of motion are described as well as functional and usability testing with stroke subjects.

  15. HENRY'S "HAND OF GOD"

    Directory of Open Access Journals (Sweden)

    Željko Kaluđerović

    2014-04-01

    Full Text Available In this paper the author discusses the views and statements of the French football player Thierry Henry he gave after his illegal play during the playoff match between France and the Republic of Ireland to claim one of the final spots in the World Cup 2010 in South Africa. First, by controlling the ball with his hand before passing it on for the goal Henry has shown disregard for the constitutive rules of football. Then, by stating that he is "not a referee" he demonstrated that for some players rules are not inherent to football and that they can be relativized, given that for them winning is the goal of the highest ontological status. Furthermore, he has rejected the rules of sportsmanship, thus expressing his opinion that the opponents are just obstacles which have to be removed in order to achieve your goals. Henry's action has disrupted major moral values, such as justice, honesty, responsibility and beneficence. The rules of fair play have totally been ignored both in Henry's action and in the Football Association of France's unwillingness to comment on whether a replay should take place. They have ignored one of the basic principles stated in the "Declaration of the International Fair Play Committee", according to which, fair play is much more than playing to the rules of the game; it's about the attitude of the sportsperson. It's about respecting your opponent and preserving his or her physical and psychological integrity. Finally, the author believes that the rules, moral values and fair play in football are required for this game to become actually possible to play.

  16. [Hand involvement in systemic sclerosis].

    Science.gov (United States)

    Mouthon, Luc

    2013-12-01

    Hand involvement is very common in patients with systemic sclerosis and represents an important tool for the early diagnosis of the disease. Vascular involvement of the hands is at the forefront of systemic sclerosis, with Raynaud's phenomenon, which may be complicated by digital ulcers, digital necrosis causing pain, infection and significant disability. Joint inflammation can also be disabling and causes the occurrence of contractures and deformities resulting in a marked hand disability. Skin sclerosis involving fingers and hands leads to the occurrence of pain and functional impairment. Hand involvement contributes to 75 % of global disability in patients with systemic sclerosis. Only a comprehensive care, taking into account the vascular, skin and joint manifestations, including physical therapy if needed can improve hand function in patients with systemic sclerosis.

  17. A LiDAR based analysis of hydraulic hazard mapping

    Science.gov (United States)

    Cazorzi, F.; De Luca, A.; Checchinato, A.; Segna, F.; Dalla Fontana, G.

    2012-04-01

    Mapping hydraulic hazard is a ticklish procedure as it involves technical and socio-economic aspects. On the one hand no dangerous areas should be excluded, on the other hand it is important not to exceed, beyond the necessary, with the surface assigned to some use limitations. The availability of a high resolution topographic survey allows nowadays to face this task with innovative procedures, both in the planning (mapping) and in the map validation phases. The latter is the object of the present work. It should be stressed that the described procedure is proposed purely as a preliminary analysis based on topography only, and therefore does not intend in any way to replace more sophisticated analysis methods requiring based on hydraulic modelling. The reference elevation model is a combination of the digital terrain model and the digital building model (DTM+DBM). The option of using the standard surface model (DSM) is not viable, as the DSM represents the vegetation canopy as a solid volume. This has the consequence of unrealistically considering the vegetation as a geometric obstacle to water flow. In some cases the topographic model construction requires the identification and digitization of the principal breaklines, such as river banks, ditches and similar natural or artificial structures. The geometrical and topological procedure for the validation of the hydraulic hazard maps is made of two steps. In the first step the whole area is subdivided into fluvial segments, with length chosen as a reasonable trade-off between the need to keep the hydrographical unit as complete as possible, and the need to separate sections of the river bed with significantly different morphology. Each of these segments is made of a single elongated polygon, whose shape can be quite complex, especially for meandering river sections, where the flow direction (i.e. the potential energy gradient associated to the talweg) is often inverted. In the second step the segments are analysed

  18. Hands-on Virtual Clay

    OpenAIRE

    Pihuit, Adeline; Kry, Paul; Cani, Marie-Paule

    2008-01-01

    poster; International audience; This paper presents a new interaction system designed for hands-on 3D shape modeling and deformation through natural hand gestures. Our system is made of a Phantom haptic device coupled with a deformable foam ball that supports pressure sensors. These sensors detect forces exerted by the user's fingertips, and are used to control the configuration of a compliant virtual hand that is modeling soft virtual clay. During interaction, the user is provided both passi...

  19. Mechanical and hydraulic properties of rocks related to induced seismicity

    Science.gov (United States)

    Witherspoon, P.A.; Gale, J.E.

    1977-01-01

    Witherspoon, P.A. and Gale, J.E., 1977. Mechanical and hydraulic properties of rocks related to induced seismicity. Eng. Geol., 11(1): 23-55. The mechanical and hydraulic properties of fractured rocks are considered with regard to the role they play in induced seismicity. In many cases, the mechanical properties of fractures determine the stability of a rock mass. The problems of sampling and testing these rock discontinuities and interpreting their non-linear behavior are reviewed. Stick slip has been proposed as the failure mechanism in earthquake events. Because of the complex interactions that are inherent in the mechanical behavior of fractured rocks, there seems to be no simple way to combine the deformation characteristics of several sets of fractures when there are significant perturbations of existing conditions. Thus, the more important fractures must be treated as individual components in the rock mass. In considering the hydraulic properties, it has been customary to treat a fracture as a parallel-plate conduit and a number of mathematical models of fracture systems have adopted this approach. Non-steady flow in fractured systems has usually been based on a two-porosity model, which assumes the primary (intergranular) porosity contributes only to storage and the secondary (fracture) porosity contributes only to the overall conductivity. Using such a model, it has been found that the time required to achieve quasi-steady state flow in a fractured reservoir is one or two orders of magnitude greater than it is in a homogeneous system. In essentially all of this work, the assumption has generally been made that the fractures are rigid. However, it is clear from a review of the mechanical and hydraulic properties that not only are fractures easily deformed but they constitute the main flow paths in many rock masses. This means that one must consider the interaction of mechanical and hydraulic effects. A considerable amount of laboratory and field data is now

  20. On Semantic Development of HAND

    Institute of Scientific and Technical Information of China (English)

    黎金娥

    2015-01-01

    The body-part term, HAND, ranks 48 in Swadesh's 100-Word List.This paper discusses the origin and meanings, and then the rules of semantic development in the HAND semantic field by comparing with other languages.The word itself does not only denote the body part but also things resembling hands in shape, position, function and things associated with hands.Plenty of linguistic evidence can be found to illustrate that all human beings regard their bodies as the basis and starting point of recognition of the whole world.

  1. Neutrophilic dermatosis of dorsal hands

    Directory of Open Access Journals (Sweden)

    S Kaur

    2015-01-01

    Full Text Available Sweet′s syndrome is characterized by erythematous tender nodules and plaques over face and extremities. Fever, leukocytosis with neutrophilia, and a neutrophilic infiltrate in the dermis are characteristic features. Neutrophilic dermatosis of dorsal hands is a rare localized variant of Sweet′s syndrome occurring predominantly over dorsa of hands. Various degrees of vascular damage may be observed on histopathology of these lesions. Both Sweet′s syndrome and its dorsal hand variant have been reported in association with malignancies, inflammatory bowel diseases, and drugs. We report a patient with neutrophilic dermatoses of dorsal hands associated with erythema nodosum. He showed an excellent response to corticosteroids and dapsone.

  2. Mechatronic Hydraulic Drive with Regulator, Based on Artificial Neural Network

    Science.gov (United States)

    Burennikov, Y.; Kozlov, L.; Pyliavets, V.; Piontkevych, O.

    2017-06-01

    Mechatronic hydraulic drives, based on variable pump, proportional hydraulics and controllers find wide application in technological machines and testing equipment. Mechatronic hydraulic drives provide necessary parameters of actuating elements motion with the possibility of their correction in case of external loads change. This enables to improve the quality of working operations, increase the capacity of machines. The scheme of mechatronic hydraulic drive, based on the pump, hydraulic cylinder, proportional valve with electrohydraulic control and programmable controller is suggested. Algorithm for the control of mechatronic hydraulic drive to provide necessary pressure change law in hydraulic cylinder is developed. For the realization of control algorithm in the controller artificial neural networks are used. Mathematical model of mechatronic hydraulic drive, enabling to create the training base for adjustment of artificial neural networks of the regulator is developed.

  3. DCS Hydraulics Submittal, Valencia County, New Mexico, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Hydraulics data includes spatial datasets and data tables necessary for documenting the hydraulic procedures for computing flood elevations for a flood insurance...

  4. Chapter 12. Pure Tap Water Hydraulic Systems and Applications

    DEFF Research Database (Denmark)

    Conrad, Finn; Adelstorp, Anders

    1997-01-01

    Presentation of developed a modern pure tap water hydraulic components (Nessie), systems and industrial applications.......Presentation of developed a modern pure tap water hydraulic components (Nessie), systems and industrial applications....

  5. A tensor approach to the estimation of hydraulic conductivities in ...

    African Journals Online (AJOL)

    2006-07-03

    Jul 3, 2006 ... The HC values computed from the data measured on the weathered or ... Keywords: hydraulic conductivity tensor, roughness, combined stress, hydraulic aperture, Table Mountain ... the anisotropic nature of studied media.

  6. Hand in Hand: Media Literacy and Internet Safety

    Science.gov (United States)

    Gallagher, Frank

    2011-01-01

    Internet safety cannot be effectively taught without also teaching media literacy. The two go hand in hand, and both are necessary, but neither is sufficient. To understand why, it is important to first appreciate what the real risks to children are. Many of the early Internet safety programs were based on a fear of predators. Predators turned out…

  7. Stery-hand: A new device to support hand disinfection.

    Science.gov (United States)

    Szilagyi, Laszlo; Lehotsky, Akos; Nagy, Melinda; Haidegger, Tamas; Benyo, Balazs; Benyo, Zoltan

    2010-01-01

    Incomplete disinfection can cause serious complications in surgical care. The teaching of effective hand washing is crucial in modern medical training. To support the objective evaluation of hand disinfection, we developed a compact, mobile device, relying on digital imaging and image processing. The hardware consists of a metal case with matte black interior, ultra-violet lighting and a digital camera. Image segmentation and clustering are performed on a regular notebook. The hand washing procedures performed with a soap mixed with UV-reflective powder. This results the skin showing bright under UV light only on the treated (sterile) surfaces. When the surgeon inserts its hands into the box, the camera placed on the top takes an image of the hand for evaluation. The software performs the segmentation and clustering automatically. First, the hand contour is determined from the green intensity channel of the recorded RGB image. Then, the pixels of the green channel belonging to the hand are partitioned to three clusters using a quick, histogram based fuzzy c-means algorithm. The optimal threshold between the intensities of clean and dirty areas is extracted using these clusters, while the final approximated percentage of the clean area is computed using a weighting formula. The main advantage of our device is the ability to obtain objective and comparable result on the quality of hand disinfection. It may find its best use in the clinical education and training.

  8. Hand in Hand: Media Literacy and Internet Safety

    Science.gov (United States)

    Gallagher, Frank

    2011-01-01

    Internet safety cannot be effectively taught without also teaching media literacy. The two go hand in hand, and both are necessary, but neither is sufficient. To understand why, it is important to first appreciate what the real risks to children are. Many of the early Internet safety programs were based on a fear of predators. Predators turned out…

  9. Encourage student learning of hydraulic matters by the use of Arduino platform

    Science.gov (United States)

    Rodriguez Sinobas, Leonor; Granja García, Javier; Sánchez Calvo, Raúl

    2014-05-01

    Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It's intended for several purposes to anyone interested in creating interactive objects or environments. The hydraulic matters teach at the Agricultural Engineering School at the Technical University of Madrid deal with practical issues regarding the measurement of variables such as pressure, discharge, temperature and soil water content. Most of the data loggers available in the market for these variables at expensive and not always affordable. On the other hand, current students are eager to manage new technological devices thus, their skills could be oriented not only to the application of an electronic platform as Arduino to build low cost data loggers for different purposes, but to encourage their learning in the hydraulic matters improving their self esteem

  10. Hand Grip Strength and Myocardial Oxygen Consumption Index among Coronary Artery Bypass Grafting Patients

    Directory of Open Access Journals (Sweden)

    Siti Nur Baait Biniti Mohd Sokran

    2015-07-01

    Full Text Available Background: Hand grip strength (HGS is a reliable indicator of peripheral muscle strength. Although, numerous studies have investigated the strength of hand grip; little attention has been given to coronary artery disease (CAD patients, exploring the relationship between HGS and myocardial oxygen consumption (MVO2 index. The current study aimed to evaluate the interaction between HGS and MVO2 index findings before and after cardiac surgery. Methods: Twenty-seven patients with CAD had HGS were assessed using handheld dynamometer. HGS for each hand were documented. MVO2 index was assessed using rate pressure product (RPP, which is the product of the heart rate (HR and systolic blood pressure (SBP. Repeated measures MANOVA were carried out to estimate the interaction between both hands HGS and MVO2 index before and after surgery. Results: There was significant interactions (P<0.001 for both HGS dominant and non-dominant with large effect sizes (HGS dominant×MVO2 index: hp2=0.44; HGS dominant×RPP: hp2=0.49. This signifies that peripheral muscle strength of the upper limb (HGS dominant and non-dominant had different effects on MVO2 index before and after surgery. The interaction graph shows that the increase in MVO2 index after surgery was significantly greater for peripheral muscle strength of the dominant hand when compared to non-dominant. Conclusion: Patients with CAD had interactions between HGS and oxygen consumption before and after surgery. Hence, HGS might be used as a predictor to assess oxygen consumption among cardiac patients.

  11. The human hand as an inspiration for robot hand development

    CERN Document Server

    Santos, Veronica

    2014-01-01

    “The Human Hand as an Inspiration for Robot Hand Development” presents an edited collection of authoritative contributions in the area of robot hands. The results described in the volume are expected to lead to more robust, dependable, and inexpensive distributed systems such as those endowed with complex and advanced sensing, actuation, computation, and communication capabilities. The twenty-four chapters discuss the field of robotic grasping and manipulation viewed in light of the human hand’s capabilities and push the state-of-the-art in robot hand design and control. Topics discussed include human hand biomechanics, neural control, sensory feedback and perception, and robotic grasp and manipulation. This book will be useful for researchers from diverse areas such as robotics, biomechanics, neuroscience, and anthropologists.

  12. Tactile display on the remaining hand for unilateral hand amputees

    Directory of Open Access Journals (Sweden)

    Li Tao

    2016-09-01

    Full Text Available Human rely profoundly on tactile feedback from fingertips to interact with the environment, whereas most hand prostheses used in clinics provide no tactile feedback. In this study we demonstrate the feasibility to use a tactile display glove that can be worn by a unilateral hand amputee on the remaining healthy hand to display tactile feedback from a hand prosthesis. The main benefit is that users could easily distinguish the feedback for each finger, even without training. The claimed advantage is supported by preliminary tests with healthy subjects. This approach may lead to the development of effective and affordable tactile display devices that provide tactile feedback for individual fingertip of hand prostheses.

  13. Dynamic Hand Gesture Recognition Using the Skeleton of the Hand

    Directory of Open Access Journals (Sweden)

    Coquin Didier

    2005-01-01

    Full Text Available This paper discusses the use of the computer vision in the interpretation of human gestures. Hand gestures would be an intuitive and ideal way of exchanging information with other people in a virtual space, guiding some robots to perform certain tasks in a hostile environment, or interacting with computers. Hand gestures can be divided into two main categories: static gestures and dynamic gestures. In this paper, a novel dynamic hand gesture recognition technique is proposed. It is based on the 2D skeleton representation of the hand. For each gesture, the hand skeletons of each posture are superposed providing a single image which is the dynamic signature of the gesture. The recognition is performed by comparing this signature with the ones from a gesture alphabet, using Baddeley's distance as a measure of dissimilarities between model parameters.

  14. Dynamic Hand Gesture Recognition Using the Skeleton of the Hand

    Science.gov (United States)

    Ionescu, Bogdan; Coquin, Didier; Lambert, Patrick; Buzuloiu, Vasile

    2005-12-01

    This paper discusses the use of the computer vision in the interpretation of human gestures. Hand gestures would be an intuitive and ideal way of exchanging information with other people in a virtual space, guiding some robots to perform certain tasks in a hostile environment, or interacting with computers. Hand gestures can be divided into two main categories: static gestures and dynamic gestures. In this paper, a novel dynamic hand gesture recognition technique is proposed. It is based on the 2D skeleton representation of the hand. For each gesture, the hand skeletons of each posture are superposed providing a single image which is the dynamic signature of the gesture. The recognition is performed by comparing this signature with the ones from a gesture alphabet, using Baddeley's distance as a measure of dissimilarities between model parameters.

  15. The use of asphalt in hydraulic engineering

    NARCIS (Netherlands)

    Van de Velde, P.A.; Ebbens, E.H.; Van Herpen, J.A.

    1985-01-01

    Asphalt products have been used in the Netherlands in hydraulic engineering for a long time on a large scale, especially after the great disaster in 1953 when a large part of western Holland was flooded by the sea. After the disaster a great number of dikes had to be repaired very quickly and this w

  16. Elevator and hydraulics; Elevator to yuatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, I. [Hitachi, Ltd., Tokyo (Japan)

    1994-07-15

    A hydraulic type elevator is installed in relatively lower buildings as compared with a rope type elevator, but the ratio in the number of installation of the former elevator is increasing. This paper explains from its construction and features to especially various control systems for the riding comfort and safety. A direct push-up system with hydraulic jacks arranged beneath a car, and an indirect push-up system that has hydraulic jacks arranged on flank of a car and transmits the movement of a plunger via a rope are available. The latter system eliminates the need of large holes to embed hydraulic jacks. While the speed is controlled by controlling flow rates of high-pressure oil, the speed, position, acceleration and even time differential calculus of the acceleration must be controlled severely. The system uses two-step control for the through-speed and the landing speed. Different systems that have been realized may include compensation for temperatures in flow rate control valves, load pressures, and oil viscosity, from learning control to fuzzy control for psychological effects, or control of inverters in motors. 13 refs., 12 figs., 1 tab.

  17. Hydraulic adjustment of Scots pine across Europe

    NARCIS (Netherlands)

    Martínez-Vilalta, J.; Cochard, H.; Mencuccini, M.; Sterck, F.J.; Herrero, A.; Korhonen, J.F.J.; Llorens, P.; Nikinmaa, E.; Nolè, A.; Poyatos, R.; Ripullone, F.; Sass-Klaassen, U.; Zweifel, R.

    2009-01-01

    The variability of branch-level hydraulic properties was assessed across 12 Scots pine populations covering a wide range of environmental conditions, including some of the southernmost populations of the species. The aims were to relate this variability to differences in climate, and to study the po

  18. Influence of tray hydraulics on tray column

    NARCIS (Netherlands)

    Betlem, Bernardus H.L.; Rijnsdorp, J.E.; Rijnsdorp, J.E.; Azink, R.F.

    1998-01-01

    To column control, in contrast to column design, tray hold-up and dependencies of tray hold-up on the operating conditions play an important role. The essence of this article is the development of an improved model of tray hydraulics over a broad operating range and its experimental validation by

  19. Design of a hydraulic bending machine

    Science.gov (United States)

    Steven G. Hankel; Marshall Begel

    2004-01-01

    To keep pace with customer demands while phasing out old and unserviceable test equipment, the staff of the Engineering Mechanics Laboratory (EML) at the USDA Forest Service, Forest Products Laboratory, designed and assembled a hydraulic bending test machine. The EML built this machine to test dimension lumber, nominal 2 in. thick and up to 12 in. deep, at spans up to...

  20. Sustainable hydraulic engineering through building with nature

    NARCIS (Netherlands)

    Vriend, de H.J.; Koningsveld, van M.; Aarninkhof, S.G.J.; Vries, de M.B.; Baptist, M.J.

    2015-01-01

    Hydraulic engineering infrastructures are of concern to many people and are likely to interfere with the environment. Moreover, they are supposed to keep on functioning for many years. In times of rapid societal and environmental change this implies that sustainability and adaptability are important

  1. The use of asphalt in hydraulic engineering

    NARCIS (Netherlands)

    Van de Velde, P.A.; Ebbens, E.H.; Van Herpen, J.A.

    1985-01-01

    Asphalt products have been used in the Netherlands in hydraulic engineering for a long time on a large scale, especially after the great disaster in 1953 when a large part of western Holland was flooded by the sea. After the disaster a great number of dikes had to be repaired very quickly and this w

  2. International Institute for Hydraulic and Environmental Engineering

    Science.gov (United States)

    Mostertman, L. J.

    1977-01-01

    Describes the activities of the International Institute for Hydraulic and Environmental Engineering (IHE), whose primary function is the promotion of the better use of water resources as a vehicle of development by the transfer of knowledge and experience. (Author/RK)

  3. Digital hydraulic valving system. [design and development

    Science.gov (United States)

    1973-01-01

    The design and development are reported of a digital hydraulic valving system that would accept direct digital inputs. Topics include: summary of contractual accomplishments, design and function description, valve parameters and calculations, conclusions, and recommendations. The electrical control circuit operating procedure is outlined in an appendix.

  4. Sustainable hydraulic engineering through building with nature

    NARCIS (Netherlands)

    Vriend, de H.J.; Koningsveld, van M.; Aarninkhof, S.G.J.; Vries, de M.B.; Baptist, M.J.

    2015-01-01

    Hydraulic engineering infrastructures are of concern to many people and are likely to interfere with the environment. Moreover, they are supposed to keep on functioning for many years. In times of rapid societal and environmental change this implies that sustainability and adaptability are important

  5. Reactive barriers: hydraulic performance and design enhancements.

    Science.gov (United States)

    Painter, B D M

    2004-01-01

    The remediation of contaminated ground water is a multibillion-dollar global industry. Permeable reactive barriers (PRBs) are one of the leading technologies being developed in the search for alternatives to the pump-and-treat method. Improving the hydraulic performance of these PRBs is an important part of maximizing their potential to the industry. Optimization of the hydraulic performance of a PRB can be defined in terms of finding the balance between capture, residence time, and PRB longevity that produces a minimum-cost acceptable design. Three-dimensional particle tracking was used to estimate capture zone and residence time distributions. Volumetric flow analysis was used for estimation of flow distribution across a PRB and in the identification of flow regimes that may affect the permeability or reactivity of portions of the PRB over time. Capture zone measurements extended below the base of partially penetrating PRBs and were measured upgradient from the portion of aquifer influenced by PRB emplacement. Hydraulic performance analysis of standard PRB designs confirmed previously presented research that identified the potential for significant variation in residence time and capture zone. These variations can result in the need to oversize the PRB to ensure that downgradient contaminant concentrations do not exceed imposed standards. The most useful PRB design enhancements for controlling residence time and capture variation were found to be customized downgradient gate faces, velocity equalization walls, deeper emplacement of the funnel than the gate, and careful manipulation of the hydraulic conductivity ratio between the gate and the aquifer.

  6. SITMILARITY LAW FOR HYDRAULIC DISTORTED MODEL

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Newton's general similarity criterion was applied to the distorted model. The results for the similarities of gravity force, drag force and pressure force are identical with those derived from relevant differential equations of fluid flow. And the selected limits of the distorted ratio were studied and the simulation of roughness coefficient of distorted model was conducted by means of hydraulic test.

  7. Separation and pattern formation in hydraulic jumps

    DEFF Research Database (Denmark)

    Bohr, Tomas; Ellegaard, C.; Hansen, A. Espe;

    1998-01-01

    We present theory and experiments on the circular hydraulic jump in the stationary regime. The theory can handle the situation in which the fluid flows over an edge far away from the jump. In the experiments the external height is controlled, and a series of transitions in the flow structure appe...

  8. HYDRAULIC CONDUCTIVITY OF THREE GEOSYNTHETIC CLAY LINERS

    Science.gov (United States)

    The hydraulic conductivity of three 2.9 m2 (32 sq ft) geosynthetic clay liners (GCLs) was measured. Tests were performed on individual sheets of the GCLs, on overlapped pieces of GCLs, and on composite liners consisting of a punctured geomembrane overlying a GCL. Hyd...

  9. Towards Autonomous Control of Hydraulic Actuator Systems

    DEFF Research Database (Denmark)

    Hansen, Poul Erik; Conrad, Finn

    1998-01-01

    Presentation of new developed control algorithms to increase autonomy and intelligence of hydraulic control systems. A refinement of relaytuning method is used to determine the control parameters of a lag/lead controller and a poleplacement controller. Further, a fail-safe function is developed t...

  10. Power management in hydraulically actuated mobile equipment

    DEFF Research Database (Denmark)

    Pedersen, Henrik Clemmensen; Andersen, Torben Ole; Hansen, Michael Rygaard

    2008-01-01

    The focus of the current paper is on the control of hydraulic systems when utilizing the advances that electronic control may bring with regard to power management, prioritized flow sharing and anti-stall, arising from being able to control both pump, valves and engine electronically. A simple mo...

  11. Dentin permeability: determinants of hydraulic conductance.

    Science.gov (United States)

    Reeder, O W; Walton, R E; Livingston, M J; Pashley, D H

    1978-02-01

    A technique is described which permits measurements of the ease with which fluid permeates dentin. This value, the hydraulic conductance of dentin, increased as surface area increases and/or as dentin thickness decreases. It increased 32-fold when dentin was acid etched due to removal of surface debris occluding the tubules.

  12. Square Wheels and Other Easy-To-Build Hands-On Science Activities. An Exploratorium Science Snackbook.

    Science.gov (United States)

    Rathjen, Don; Doherty, Paul

    This book, part of The Exploratorium science "snackbook" series, explains science with a hands-on approach. Activities include: (1) "3-D Shadow"; (2) "Bits and Bytes"; (3) "Circuit Workbench"; (4) "Diamagnetic Repulsion"; (5) "Film Can Racer"; (6) "Fractal Patterns"; (7) "Hoop Nightmares"; (8) "Hydraulic Arm"; (9) "Hyperbolic Slot"; (10) "Light…

  13. Analysis of Innovative Design of Energy Efficient Hydraulic Actuators

    OpenAIRE

    M Osman Abdalla

    2013-01-01

    Hydraulic cylinder actuators are used extensively in industrial, construction and agricultural works. The small sized outlet ports of the cylinders resist the flow of discharged oil; and as a result the piston motion is slowed down. This causes a lot of heat generation and energy loss within the actuators. The study investigates and analyzes the possibilities of reducing the hydraulic resistance and increasing efficiency of the hydraulic actuator. Conventional hydraulic cylinders are simulate...

  14. DISCONTINUOUS FLOW OF TURBID DENSITY CURRENTS Ⅱ. INTERNAL HYDRAULIC JUMP

    Institute of Scientific and Technical Information of China (English)

    Jiahua FAN

    2005-01-01

    Traveling and stationary internal hydraulic jumps in density currents with positive or negative entrainment coefficients were analyzed based on simple assumptions. An expression of internal hydraulic jumps with entrainment coefficients was derived. Experimental data, published in literature, of stationary internal hydraulic jumps in turbid, thermal and saline density currents including measured values of water entrainment were used to compare with theory. Comparison was also made of traveling internal hydraulic jumps between measured data and theory.

  15. OPTIMAL HYDRAULIC DESIGN AND CAD APPLICATIONS OF AXIAL FLOW HYDRAULIC TURBINE'S RUNNER

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A method of the optimal hydraulic design and CAD application of runner blades of axial-flow hydraulic turbines are discussed on the basis of optimization principle and CAD technique in this paper. Based on the theory of fluid dynamics, the blade′s main geometrical parameter, working parameters and performances index of the blades and the relationship between them are analysed, and the mathematical model of optimal hydraulic design of axial-flow runners has been established. Through nonlinear programming, the problems can be solved. By making use of the calculation geometry and computer graphics, the distribution method of the singular points, and an CAD applied software, an optimal hydraulic design are presented.

  16. Hydraulic Bureaucracy in a Modern Hydraulic Society – Strategic Group Formation in the Mekong Delta, Vietnam

    Directory of Open Access Journals (Sweden)

    Hans-Dieter Evers

    2009-10-01

    Among these strategic groups, the hydraulic bureaucracy and hydraulic construction business are the most crucial in terms of the specific role they play in the hydraulic landscape of the Mekong delta. Both groups exert considerable influence on water resources management and strive for the same resources, namely public funds (including Overseas Development Aid that is directed to hydraulic infrastructure development. This paper illustrates how both groups have emerged due to the growing need for water resources management in the delta and how they have set up alliances for mutually sharing resources in the long run. Furthermore, it is shown how both groups have adapted their resource-oriented strategies and actions to respond to the changes in the economic and political environment in Vietnam’s recent history.

  17. Hydraulic power take-off for wave energy systems

    DEFF Research Database (Denmark)

    Christensen, Georg Kronborg

    2001-01-01

    Investigation and laboratory experiments with a hydraulic power conversion system for converting forces from a 2.5m diamter float to extract energy from seawaves. The test rig consists of a hydraulic wave simulator and a hydraulic point absorber. The absorber converts the incomming forces...

  18. 21 CFR 880.5110 - Hydraulic adjustable hospital bed.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hydraulic adjustable hospital bed. 880.5110... (CONTINUED) MEDICAL DEVICES GENERAL HOSPITAL AND PERSONAL USE DEVICES General Hospital and Personal Use Therapeutic Devices § 880.5110 Hydraulic adjustable hospital bed. (a) Identification. A hydraulic adjustable...

  19. 14 CFR 33.72 - Hydraulic actuating systems.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hydraulic actuating systems. 33.72 Section... AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Design and Construction; Turbine Aircraft Engines § 33.72 Hydraulic actuating systems. Each hydraulic actuating system must function properly under all conditions in which...

  20. 7 CFR 2902.10 - Mobile equipment hydraulic fluids.

    Science.gov (United States)

    2010-01-01

    ... Comprehensive Procurement Guideline, 40 CFR 247.11. ... 7 Agriculture 15 2010-01-01 2010-01-01 false Mobile equipment hydraulic fluids. 2902.10 Section... PROCUREMENT Designated Items § 2902.10 Mobile equipment hydraulic fluids. (a) Definition. Hydraulic...

  1. Comparison of four methods to assess hydraulic conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Benson, C.H. [Univ. of Wisconsin, Madison, WI (United States). Dept. of Civil and Environmental Engineering; Gunter, J.A. [Gunter (John A.), Round Rock, TX (United States); Boutwell, G.P. [STE, Inc., Baton Rouge, LA (United States); Trautwein, S.J. [Trautwein Soil Testing Equipment Co., Houston, TX (United States); Berzanskis, P.H. [Hoechst-Celanese, Inc., Pampa, TX (United States)

    1997-10-01

    A hydraulic conductivity assessment that was conducted on four test pads constructed to the same specifications with soil from the same source by four different contractors is described. The test pads had distinctly different field hydraulic conductivities, even though they were constructed with similar soil, to similar compaction conditions, and with similar machinery. Adequate hydration time was key in achieving low field hydraulic conductivity. More extensive processing was another factor responsible for low field hydraulic conductivity. Four different test methods were used to assess the hydraulic conductivity of each test pad: (1) sealed double-ring infiltrometers (SDRIs); (2) two-stage borehole permeameters; (3) laboratory hydraulic conductivity tests on large block specimens; and (4) laboratory hydraulic conductivity tests on small specimens collected in thin-wall sampling tubes. The tests were conducted independently by each of the writers. After the tests were completed, the results were submitted and compared. Analysis of the test results show that the three large-scale test methods generally yield similar hydraulic conductivities. For two of the test pads, however, the hydraulic conductivities of the specimens collected in sampling tubes were significantly lower than the field hydraulic conductivities. Both of these test pads had high field hydraulic conductivity. Thus, there is little value in using small specimens to assess field hydraulic conductivity.

  2. 23 CFR 650.111 - Location hydraulic studies.

    Science.gov (United States)

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Location hydraulic studies. 650.111 Section 650.111 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS BRIDGES, STRUCTURES, AND HYDRAULICS Location and Hydraulic Design of Encroachments on Flood Plains §...

  3. Giant lipomas of the hand

    Directory of Open Access Journals (Sweden)

    Gokce Yildiran

    2015-04-01

    Conclusion: Giant lipomas of the hand are very rare and may cause compressions and other complications. Thus, they require a careful preoperative evaluation in order to make a proper differential diagnosis. [Hand Microsurg 2015; 4(1.000: 8-11

  4. Please wash your hands often

    OpenAIRE

    2007-01-01

    This poster advises washing hands "before and after using the toilet, handling food, touching animals, eating, drinking, or smoking." It advocates "always use clean water / never wash your hands in used wash water!" The purpose is to protect self and others from diseases. LTRA-2 (An Agricultural Markets Model for Biodiversity Conservation)

  5. Canadian hand dermatitis management guidelines

    DEFF Research Database (Denmark)

    Lynde, Charles; Guenther, Lyn; Diepgen, Thomas L;

    2010-01-01

    Hand dermatitis (HD) is one of the most common skin conditions; however, it is not a homogeneous disease entity. The severity of HD may range from very mild cases to severe chronic forms, which may result in prolonged disability and, occasionally, refractory HD. Chronic hand dermatitis (CHD...

  6. Canadian hand dermatitis management guidelines

    DEFF Research Database (Denmark)

    Lynde, Charles; Guenther, Lyn; Diepgen, Thomas L

    2010-01-01

    Hand dermatitis (HD) is one of the most common skin conditions; however, it is not a homogeneous disease entity. The severity of HD may range from very mild cases to severe chronic forms, which may result in prolonged disability and, occasionally, refractory HD. Chronic hand dermatitis (CHD) is a...

  7. The Work of the Hand

    Science.gov (United States)

    Ludick, Pat

    2013-01-01

    Recognizing Maria and Mario Montessori's reverence for the hand, Pat Ludick takes the reader into the wonder of the human body, mind, and spirit and across the planes of education, into the making of a whole personality and grounded intelligence that is ready for the adult world. Putting the hand front and center, she lyrically evolves an overview…

  8. Hand controller commonality evaluation process

    Science.gov (United States)

    Stuart, Mark A.; Bierschwale, John M.; Wilmington, Robert P.; Adam, Susan C.; Diaz, Manuel F.; Jensen, Dean G.

    1993-01-01

    Hand controller selection for NASA's Orbiter and Space Station Freedom is an important area of human-telerobot interface design and evaluation. These input devices will control remotely operated systems that include large crane-like manipulators (e.g., Remote Manipulator System or RMS), smaller, more dexterous manipulators (e.g., Flight Telerobotic Servicer or FTS), and free flyers (e.g., Orbital Maneuvering Vehicle or OMV). Candidate hand controller configurations for these systems vary in many ways: shape, size, number of degrees-of-freedom (DOF), operating modes, provision of force reflection, range of movement, and 'naturalness' of use. Unresolved design implementation issues remain, including such topics as how the current Orbiter RMS rotational and translational rate hand controllers compare with the proposed Space Station Freedom hand controllers, the advantages that position hand controllers offer for these applications, and whether separate hand controller configurations are required for each application. Since previous studies contain little empirical hand controller task performance data, a controlled study is needed that tests Space Station Freedom candidate hand controllers during representative tasks. This study also needs to include anthropometric and biomechanical considerations.

  9. The Left-Handed Writer.

    Science.gov (United States)

    Bloodsworth, James Gaston

    Contrary to the beliefs of many, right-handedness is not a single factor existing in almost all people, with a few exceptions termed left-handed: neither extreme exists independently of the other. During the first 4 years of life there is a period of fluctuation between right and left-handed dominance. Statistics and findings vary in determining…

  10. Robot Forearm and Dexterous Hand

    Science.gov (United States)

    Lovchik, Christopher S.

    2005-01-01

    An electromechanical hand-and-forearm assembly has been developed for incorporation into an anthropomorphic robot that would be used in outer space. The assembly is designed to offer manual dexterity comparable to that of a hand inside an astronaut s suit; thus, the assembly may also be useful as a prosthesis or as an end effector on an industrial robot.

  11. Hand-related physical function in rheumatic hand conditions

    DEFF Research Database (Denmark)

    Klokker, Louise; Terwee, Caroline B; Wæhrens, Eva Ejlersen;

    2016-01-01

    INTRODUCTION: There is no consensus about what constitutes the most appropriate patient-reported outcome measurement (PROM) instrument for measuring physical function in patients with rheumatic hand conditions. Existing instruments lack psychometric testing and vary in feasibility and their psych......INTRODUCTION: There is no consensus about what constitutes the most appropriate patient-reported outcome measurement (PROM) instrument for measuring physical function in patients with rheumatic hand conditions. Existing instruments lack psychometric testing and vary in feasibility...... and their psychometric qualities. We aim to develop a PROM instrument to assess hand-related physical function in rheumatic hand conditions. METHODS AND ANALYSIS: We will perform a systematic search to identify existing PROMs to rheumatic hand conditions, and select items relevant for hand-related physical function...... as well as those items from the Patient Reported Outcomes Measurement Information System (PROMIS) Physical Function (PF) item bank that are relevant to patients with rheumatic hand conditions. Selection will be based on consensus among reviewers. Content validity of selected items will be established...

  12. Hand Transplantation Versus Hand Prosthetics: Pros and Cons.

    Science.gov (United States)

    Salminger, S; Roche, A D; Sturma, A; Mayer, J A; Aszmann, O C

    Composite tissue transplantation and new developments in the field of prosthetics have opened new frontiers in the restoration of function among upper limb amputees. It is now possible to restore hand function in affected patients; however, the indications, advantages, and limitations for either hand transplantation or prosthetic fitting must be carefully considered depending on the level and extent of the limb loss. Hand transplantation allows comprehensive hand function to be restored, yet composite tissue transplantation comes with disadvantages, making this method a controversial topic in the hand surgical community. Alternatively, prosthetic limb replacement represents the standard of care for upper limb amputees, but results in the known limitations of function, sensation, and usage. The indication for hand transplantation or prosthetic fitting strongly depends on the level of amputation, as well as on the extent (unilateral/bilateral) of the amputation. In this review, we discuss the advantages and disadvantages of hand transplantation and prosthetic replacement for upper limb amputees in general, as well as in regard to the different levels of amputation.

  13. Hand eczema - prognosis and consequences

    DEFF Research Database (Denmark)

    Petersen, A. H.; Johansen, J D; Hald, M

    2014-01-01

    BACKGROUND: Hand eczema is recognized as a long-lasting disease with personal and societal repercussions. Long-term studies are required to generate information on factors contributing to a poor outcome. OBJECTIVES: The aims of this 7-year follow-up study were to evaluate the clinical course...... of patients with hand eczema, the occupational consequences and to identify risk factors associated with a poor prognosis. MATERIALS AND METHODS: In all, 536 patients with hand eczema participated and were examined by a dermatologist. The clinical severity was assessed at baseline and 7 years later using...... a self-administrated photographic guide. Additional information was obtained from a questionnaire. RESULTS: Based on the photographic guide, 73% experienced a clinical improvement. Notably, 20% had moderate to very severe hand eczema at follow-up. Severe hand eczema or frequent eruptions at baseline...

  14. Hand Detection Using HSV Model

    Directory of Open Access Journals (Sweden)

    Uzma Noreen

    2015-08-01

    Full Text Available Natural Human Computer Interaction HCI is the demand of todays technology oriented world. Detecting and tracking of face and hands are important for gesture recognition. Skin detection is a very popular and useful technique for detecting and tracking human-body parts. It has been much attention mainly because of its vast range of applications such as face detection and tracking naked people detection hand detection and tracking people retrieval in databases and Internet etc. Many models and algorithms are being used for detection of face hand and its gesture. Hand detection using model or classification is to build a decision rule that will discriminate between skin and non-skin pixels. Identifying skin color pixels involves finding the range of values for which most skin pixels would fall in a given color space. All external factors will be eliminated to detect the hand and its color in the image in complex background.

  15. 3D Printed Robotic Hand

    Science.gov (United States)

    Pizarro, Yaritzmar Rosario; Schuler, Jason M.; Lippitt, Thomas C.

    2013-01-01

    Dexterous robotic hands are changing the way robots and humans interact and use common tools. Unfortunately, the complexity of the joints and actuations drive up the manufacturing cost. Some cutting edge and commercially available rapid prototyping machines now have the ability to print multiple materials and even combine these materials in the same job. A 3D model of a robotic hand was designed using Creo Parametric 2.0. Combining "hard" and "soft" materials, the model was printed on the Object Connex350 3D printer with the purpose of resembling as much as possible the human appearance and mobility of a real hand while needing no assembly. After printing the prototype, strings where installed as actuators to test mobility. Based on printing materials, the manufacturing cost of the hand was $167, significantly lower than other robotic hands without the actuators since they have more complex assembly processes.

  16. 便携式电子测力计在肌力评定中的应用进展%Application Progress of Hand-held Dynamometry in Muscle Strength Assessment

    Institute of Scientific and Technical Information of China (English)

    关润泽; 赵鹏

    2016-01-01

    Objective and accurate evaluation of muscle strength is the core foundation of developing rehabil⁃itation programs, determining the rehabilitation goals, evaluating the treatment effects. Understand the lat⁃est research results of muscle strength testing, comparative study of manual muscle testing and isokinetic testing, hand-held dynamometer testing of a variety of muscle strength method. Results showed that hand-held dynamometer testing compared to traditional manual muscle strength testing more quantitative, and hand-held dynamometer muscle strength measurement value associated with isokinetic testing of strong(r=0.91),and the easy to operate, strong applicability, can effectively discharge effect on muscle strength assess⁃ment of muscular tension. View of hand-held dynamometer with merits of quantitative, accurate and easy to carry, can be widely used in rehabilitation assessment, screening function and monitoring training effect, so as to improve the effectiveness of rehabilitation.%客观准确地肌力评定,是制定康复治疗计划、确定康复目标、评价治疗效果的核心基石。了解现阶段肌力检测的最新研究成果,对比研究徒手肌力检测、等速仪器测试、便携式电子测力计测试等多种肌力检测方法。结果显示,便携式电子测力计相对于传统徒手肌力检测更为量化;同时便携式电子测力计肌力测量值与等速仪器测试相关性较强(r=0.91),且易于操作,应用性较强,能有效排出肌张力对肌力评定的影响。因而鉴于便携式电子测力计有定量、精确和便于携带的优点,能广泛应用于康复评定、功能筛查和训练效果监控过程中。

  17. Eye-dominance, writing hand, and throwing hand.

    Science.gov (United States)

    McManus, I C; Porac, C; Bryden, M P; Boucher, R

    1999-04-01

    Handedness and eye-dominance are undoubtedly associated statistically, although a previous meta-analysis has found that the precise relationship is difficult to explain, with about 35% of right-handers and 57% of left-handers being left eye dominant. Of particular difficulty to genetic or other models is that the proportions are distributed asymmetrically around 50%. The present study asked whether this complicated pattern of association occurred because, following Peters, it is necessary to divide right-and left-handers into consistent handers (who write and throw with the same hand) and inconsistent handers (who write and throw with opposite hands). In an analysis of 10,635 subjects from questionnaire studies, 28.8% of left-handers and 1.6% of right-handers by writing were inconsistent for throwing. Our results also showed that writing hand and throwing hand both relate independently to eyedness, that throwing hand is somewhat more strongly associated with eyedness, and that the awkward asymmetry around 50% is now removed, 24.2% of consistent right-handers being left eye dominant compared with 72.3% of consistent left-handers, and 55.4% of inconsistent right-handers compared with 47.0% of inconsistent left-handers. We conclude that eyedness is phenotypically secondary to writing and throwing handedness. In our discussion we note that eyedness runs in families, we present new data suggesting that writing hand and throwing hand are co-inherited, and we argue that further data are now required to model properly the associations of writing hand, throwing hand, and eyedness, as well as probably also footedness and language dominance.

  18. SHynergie: Development of a virtual project laboratory for monitoring hydraulic stimulations

    Science.gov (United States)

    Renner, Jörg; Friederich, Wolfgang; Meschke, Günther; Müller, Thomas; Steeb, Holger

    2016-04-01

    Hydraulic stimulations are the primary means of developing subsurface reservoirs regarding the extent of fluid transport in them. The associated creation or conditioning of a system of hydraulic conduits involves a range of hydraulic and mechanical processes but also chemical reactions, such as dissolution and precipitation, may affect the stimulation result on time scales as short as hours. In the light of the extent and complexity of these processes, the steering potential for the operator of a stimulation critically depends on the ability to integrate the maximum amount of site-specific information with profound process understanding and a large spectrum of experience. We report on the development of a virtual project laboratory for monitoring hydraulic stimulations within the project SHynergie (http://www.ruhr-uni-bochum.de/shynergie/). The concept of the laboratory envisioned product that constitutes a preparing and accompanying rather than post-processing instrument ultimately accessible to persons responsible for a project over a web-repository. The virtual laboratory consists of a data base, a toolbox, and a model-building environment. Entries in the data base are of two categories. On the one hand, selected mineral and rock properties are provided from the literature. On the other hand, project-specific entries of any format can be made that are assigned attributes regarding their use in a stimulation problem at hand. The toolbox is interactive and allows the user to perform calculations of effective properties and simulations of different types (e.g., wave propagation in a reservoir, hydraulic test). The model component is also hybrid. The laboratory provides a library of models reflecting a range of scenarios but also allows the user to develop a site-specific model constituting the basis for simulations. The laboratory offers the option to use its components following the typical workflow of a stimulation project. The toolbox incorporates simulation

  19. Assimilation of temperature and hydraulic gradients for quantifying the spatial variability of streambed hydraulics

    Science.gov (United States)

    Huang, Xiang; Andrews, Charles B.; Liu, Jie; Yao, Yingying; Liu, Chuankun; Tyler, Scott W.; Selker, John S.; Zheng, Chunmiao

    2016-08-01

    Understanding the spatial and temporal characteristics of water flux into or out of shallow aquifers is imperative for water resources management and eco-environmental conservation. In this study, the spatial variability in the vertical specific fluxes and hydraulic conductivities in a streambed were evaluated by integrating distributed temperature sensing (DTS) data and vertical hydraulic gradients into an ensemble Kalman filter (EnKF) and smoother (EnKS) and an empirical thermal-mixing model. The formulation of the EnKF/EnKS assimilation scheme is based on a discretized 1D advection-conduction equation of heat transfer in the streambed. We first systematically tested a synthetic case and performed quantitative and statistical analyses to evaluate the performance of the assimilation schemes. Then a real-world case was evaluated to calculate assimilated specific flux. An initial estimate of the spatial distributions of the vertical hydraulic gradients was obtained from an empirical thermal-mixing model under steady-state conditions using a constant vertical hydraulic conductivity. Then, this initial estimate was updated by repeatedly dividing the assimilated specific flux by estimates of the vertical hydraulic gradients to obtain a refined spatial distribution of vertical hydraulic gradients and vertical hydraulic conductivities. Our results indicate that optimal parameters can be derived with fewer iterations but greater simulation effort using the EnKS compared with the EnKF. For the field application in a stream segment of the Heihe River Basin in northwest China, the average vertical hydraulic conductivities in the streambed varied over three orders of magnitude (5 × 10-1 to 5 × 102 m/d). The specific fluxes ranged from near zero (qz < ±0.05 m/d) to ±1.0 m/d, while the vertical hydraulic gradients were within the range of -0.2 to 0.15 m/m. The highest and most variable fluxes occurred adjacent to a debris-dam and bridge pier. This phenomenon is very likely

  20. Hydraulics and pneumatics a technician's and engineer's guide

    CERN Document Server

    Parr, Andrew

    1991-01-01

    Hydraulics and Pneumatics: A Technician's and Engineer's Guide provides an introduction to the components and operation of a hydraulic or pneumatic system. This book discusses the main advantages and disadvantages of pneumatic or hydraulic systems.Organized into eight chapters, this book begins with an overview of industrial prime movers. This text then examines the three different types of positive displacement pump used in hydraulic systems, namely, gear pumps, vane pumps, and piston pumps. Other chapters consider the pressure in a hydraulic system, which can be quickly and easily controlled

  1. Effects of kinesio tape compared with non-elastic tape on hand grip strength.

    Science.gov (United States)

    Kim, Ji Young; Kim, Seong Yeol

    2016-05-01

    [Purpose] Many assumptions have been made about taping and several studies have considered tape application methods; however, the true effect of taping on muscle strength remains unclear. Most previous studies compared application techniques using Kinesio tape (KT), but studies that compared muscle strength using non-elastic tape (NT) are limited. Moreover, no studies have applied KT and NT in the same way to assess grip strength in normal subjects. The purpose of this study was to evaluate the immediate effect of application of two tapes with different elastic properties on maximal grip strength in healthy adults. [Subjects and Methods] Twenty healthy adults were divided into two groups (KT and NT). Maximal grip strength was measured with a dynamometer. Forearm extensor muscles of the dominant hand were then taped and subjects were immediately asked to perform hand grip movement with maximum strength in the same standardized manner. [Results] In the KT group, maximal grip strength was significantly increased compared to the initial value; however, in the NT group, there was no significant difference in maximal grip strength. [Conclusion] This study suggests that only Kinesio tape can increase maximal grip strength immediately after application on the extensor region of the forearm.

  2. Effects of kinesio tape compared with non-elastic tape on hand grip strength

    Science.gov (United States)

    Kim, Ji Young; Kim, Seong Yeol

    2016-01-01

    [Purpose] Many assumptions have been made about taping and several studies have considered tape application methods; however, the true effect of taping on muscle strength remains unclear. Most previous studies compared application techniques using Kinesio tape (KT), but studies that compared muscle strength using non-elastic tape (NT) are limited. Moreover, no studies have applied KT and NT in the same way to assess grip strength in normal subjects. The purpose of this study was to evaluate the immediate effect of application of two tapes with different elastic properties on maximal grip strength in healthy adults. [Subjects and Methods] Twenty healthy adults were divided into two groups (KT and NT). Maximal grip strength was measured with a dynamometer. Forearm extensor muscles of the dominant hand were then taped and subjects were immediately asked to perform hand grip movement with maximum strength in the same standardized manner. [Results] In the KT group, maximal grip strength was significantly increased compared to the initial value; however, in the NT group, there was no significant difference in maximal grip strength. [Conclusion] This study suggests that only Kinesio tape can increase maximal grip strength immediately after application on the extensor region of the forearm. PMID:27313372

  3. Hand-related physical function in rheumatic hand conditions

    DEFF Research Database (Denmark)

    Klokker, Louise; Terwee, Caroline B; Wæhrens, Eva Ejlersen

    2016-01-01

    through the use of focus groups. If patients deem necessary, we will develop new items based on the patients' input. We will examine whether it is valid to score all selected and developed items on the same scale as the original items from the PROMIS PF item bank. Our analyses will follow the methods used...... will be obtained from all participants. We aim to disseminate the results of the study through publication in international peer-reviewed journals and at international conferences....... and their psychometric qualities. We aim to develop a PROM instrument to assess hand-related physical function in rheumatic hand conditions. METHODS AND ANALYSIS: We will perform a systematic search to identify existing PROMs to rheumatic hand conditions, and select items relevant for hand-related physical function...

  4. The Marble-Hand Illusion.

    Directory of Open Access Journals (Sweden)

    Irene Senna

    Full Text Available Our body is made of flesh and bones. We know it, and in our daily lives all the senses constantly provide converging information about this simple, factual truth. But is this always the case? Here we report a surprising bodily illusion demonstrating that humans rapidly update their assumptions about the material qualities of their body, based on their recent multisensory perceptual experience. To induce a misperception of the material properties of the hand, we repeatedly gently hit participants' hand with a small hammer, while progressively replacing the natural sound of the hammer against the skin with the sound of a hammer hitting a piece of marble. After five minutes, the hand started feeling stiffer, heavier, harder, less sensitive, unnatural, and showed enhanced Galvanic skin response (GSR to threatening stimuli. Notably, such a change in skin conductivity positively correlated with changes in perceived hand stiffness. Conversely, when hammer hits and impact sounds were temporally uncorrelated, participants did not spontaneously report any changes in the perceived properties of the hand, nor did they show any modulation in GSR. In two further experiments, we ruled out that mere audio-tactile synchrony is the causal factor triggering the illusion, further demonstrating the key role of material information conveyed by impact sounds in modulating the perceived material properties of the hand. This novel bodily illusion, the 'Marble-Hand Illusion', demonstrates that the perceived material of our body, surely the most stable attribute of our bodily self, can be quickly updated through multisensory integration.

  5. Hand function after nerve repair.

    Science.gov (United States)

    Lundborg, G; Rosén, B

    2007-02-01

    Treatment of injuries to major nerve trunks in the hand and upper extremity remains a major and challenging reconstructive problem. Such injuries may cause long-lasting disabilities in terms of lost fine sensory and motor functions. Nowadays there is no surgical repair technique that can ensure recovery of tactile discrimination in the hand of an adult patient following nerve repair while very young individuals usually regain a complete recovery of functional sensibility. Post-traumatic nerve regeneration is a complex biological process where the outcome depends on multiple biological and environmental factors such as survival of nerve cells, axonal regeneration rate, extent of axonal misdirection, type of injury, type of nerve, level of the lesion, age of the patient and compliance to training. A major problem is the cortical functional reorganization of hand representation which occurs as a result of axonal misdirection. Although protective sensibility usually occurs following nerve repair, tactile discriminative functions seldom recover--a direct result of cortical remapping. Sensory re-education programmes are routinely applied to facilitate understanding of the new sensory patterns provided by the hand. New trends in hand rehabilitation focus on modulation of central nervous processes rather than peripheral factors. Principles are being evolved to maintain the cortical hand representation by using the brain capacity for visuo-tactile and audio-tactile interaction for the initial phase following nerve injury and repair (phase 1). After the start of the re-innervation of the hand (phase 2), selective de-afferentation, such as cutaneous anaesthesia of the forearm of the injured hand, allows expansion of the nerve-injured cortical hand representation, thereby enhancing the effects of sensory relearning. Recent data support the view that training protocols specifically addressing the relearning process substantially increase the possibilities for improved

  6. A novel energy recovery system for parallel hybrid hydraulic excavator.

    Science.gov (United States)

    Li, Wei; Cao, Baoyu; Zhu, Zhencai; Chen, Guoan

    2014-01-01

    Hydraulic excavator energy saving is important to relieve source shortage and protect environment. This paper mainly discusses the energy saving for the hybrid hydraulic excavator. By analyzing the excess energy of three hydraulic cylinders in the conventional hydraulic excavator, a new boom potential energy recovery system is proposed. The mathematical models of the main components including boom cylinder, hydraulic motor, and hydraulic accumulator are built. The natural frequency of the proposed energy recovery system is calculated based on the mathematical models. Meanwhile, the simulation models of the proposed system and a conventional energy recovery system are built by AMESim software. The results show that the proposed system is more effective than the conventional energy saving system. At last, the main components of the proposed energy recovery system including accumulator and hydraulic motor are analyzed for improving the energy recovery efficiency. The measures to improve the energy recovery efficiency of the proposed system are presented.

  7. Corner Detection of Hand Gesture

    Directory of Open Access Journals (Sweden)

    Lili Zhang

    2012-12-01

    Full Text Available This paper studies the methods of corner detection of hand gesture, and mainly introduces the orthogonal three-direction chain code (3OT and uses it in corner detection of hand gesture. The study is discussed from four aspects: the techniques used in corner detection, the techniques of Freeman chain code, the main idea of 3OT, the process of corner detection with 3OT and the experiments on corner detectors used for hand gesture images of 26 letters in American Sign Language are described in detail. Experiment results show that the 3OT has well performance with exact corner detection rate and least false corner’s number.

  8. Compartment Syndrome of the Hand.

    Science.gov (United States)

    Oak, Nikhil R; Abrams, Reid A

    2016-07-01

    Hand compartment syndrome has many etiologies; untreated, it has dire functional consequences. Intracompartmental pressure exceeding capillary filling pressure causes decreased tissue perfusion resulting in progressive ischemic death of compartment contents. Clinical findings can evolve. Serial physical examinations are recommended and, if equivocal, interstitial pressure monitoring is indicated. Definitive management is emergent fasciotomies with incisions designed to decompress the involved hand compartments, which could include the thenar, hypothenar, and interosseous compartments, and the carpal tunnel. Careful wound care, edema management, splinting, and hand therapy are critical. Therapy should start early postoperatively, possibly before wound closure. Copyright © 2016 Elsevier Inc. All rights reserved.

  9. Comparison of dynamic analysis of a Schilling hydraulic manipulator with experimental results

    Energy Technology Data Exchange (ETDEWEB)

    Baker, C.P.; Lew, J.Y.; Evans, M.S. [Pacific Northwest Lab., Richland, WA (United States); Magee, D.P. [Georgia Inst. of Technology, Atlanta, GA (United States). George W. Woodruff School of Mechanical Engineering

    1993-07-01

    Two independent models of the dynamics of a Schilling Titan II hydraulic manipulator were developed and compared in order to obtain an accurate model of the manipulator dynamics. These models will be used in the development of feedback control laws and active damping algorithms. One of the model is an analytical model which was developed {open_quotes}by hand{close_quotes} with the assistance of computer symbolic manipulation. The other is a numerical model developed using a commercially available dynamics code. The data from these models were then compared with experimental data from an actual Titan II manipulator.

  10. Technology of load-sensitivity used in the hydraulic system of an all-hydraulic core rig

    Institute of Scientific and Technical Information of China (English)

    XIN De-zhong; CHEN Song-ling; WANG Qing-feng

    2009-01-01

    The existing hydraulic system always have problems of temperature rise, run-ning stability and anti-interference of the implementation components, reliability of hydrau-lic components, maintenance difficulties, and other issues. With high efficiency, energy saving, reliability, easy operating, stable running, anti-interference ability, and other ad-vantages, the load-sensitive hydraulic system is more suitable for coal mine all-hydraulic core rig. Therefore, for the technical development of the coal mine all-hydraulic core rig, the load-sensitive technology employed by the rig should be of great significance.

  11. Trends in Design of Water Hydraulics

    DEFF Research Database (Denmark)

    Conrad, Finn

    2005-01-01

    The paper presents and discusses a R&D-view on trends in development and best practise in design of both low-pressure and high-pressure tap water hydraulic components and systems for motion control as well as open-ended solutions various industrial applications. The focus is on the advantages using...... ordinary tap water and the range of application areas are illustrated with examples, in particular within the food processing industry, humidification operations, water mist systems for fire fighting, high water pressure cleaners, water moisturising systems for wood processing, lumber drying process...... operate with pure water from the tap without additives of any kind. Hence water hydraulics takes the benefit of pure water as fluid being environmentally friendly, easy to clean sanitary design, non-toxic, non-flammable, inexpensive, readily available and easily disposable. The low-pressure tap water...

  12. The hydraulic fracturing of geothermal formations

    Energy Technology Data Exchange (ETDEWEB)

    Naceur, K. Ben; Economides, M.J.; Schlumberger, Dowell

    1988-01-01

    Hydraulic fracturing has been attempted in geothermal formations as a means to stimulate both production and injection wells. Since most geothermal formations contain fissures and on occasion massive natural fissures, the production behavior of the man-made fractures results in certain characteristic trends. A model is offered that allows the presence of a finite or infinite conductivity fracture intercepting a fissured medium. The method is based on a numerical discretization of the formation allowing transient interporosity flow. Type curves for pressure drawdown and cumulative production are given for infinite acting and closed reservoirs. Since most of the fissured formations exhibit a degree of anisotropy, the effects of the orientation of the hydraulic fracture with respect to the fissure planes, and of the ratio between the directional permeabilities are then discussed. Guidelines are offered as to the size of appropriate stimulation treatments based on the observed fissured behavior of the reservoir.

  13. Plug & Play Control of Hydraulic Networks

    DEFF Research Database (Denmark)

    Jensen, Tom Nørgaard

    2012-01-01

    Process Control research program, which the work presented here is a part of. An industrial case study involving a large-scale hydraulic network with non-linear dynamics is studied. The hydraulic network underlies a district heating system, which provides heating water to a number of end-users in a city...... structure has the additional benefit that structural changes such as the addition or removal of end-users are easily implementable. In this work, the problem of controlling the pressure drop at the end-users to a constant reference value is considered. This is done by the use of pumps located both...... are considered. Some of the work considers control actions which are constrained to non-negative values only. This is due to the fact that the actuators in this type of system typically consist of centrifugal pumps which are only able to deliver non-negative actuation. Other parts of the work consider control...

  14. Mechanization of hydraulic testing of chemical equipment

    Energy Technology Data Exchange (ETDEWEB)

    Bannikov, M.T.; Fridman, R.N.; Petrovnin, A.I.

    1982-09-01

    The Institute VNIIPTKhimmash has worked out a comprehensive list of equipment for testing for strength and tightness containers and heat exchangers with jackets, with mixers, also of individual parts and subassemblies for this equipment. Points out that in the test stands developed for hydraulic testing of vessels both individual and centralized recirculating water supply can be used. Concludes that a reduction in labor consumption in hydraulic testing and in servicing of all the equipment used, an increase in the mechanization of this kind of chemical equipment, and the solution of the problem of standardization not only with regard to dimensions and parameters, but also with regard to the makes and types of the materials used, will make possible a considerable increase in labor productivity and product quality.

  15. Concept Evaluation for Hydraulic Yaw System

    DEFF Research Database (Denmark)

    Stubkier, Søren; Pedersen, Henrik C.; Andersen, Torben Ole

    2013-01-01

    a suspension system on a car, leading the loads away from the turbine structure. However, to realize a soft hydraulic yaw system a new design concept must be found. As a part of the development of the new concept a preliminary concept evaluation has been conducted, evaluating seven different hydraulic yaw......The yaw system is the subsystem on a wind turbine which ensures that the rotor plane of the turbine always is facing the wind direction. Studies from [1] show that a soft yaw system may be utilized to dampen the loads in the wind turbine structure. The soft yaw system operates much like...... investigation. Loads and yaw demands are based on the IEC 61400-1 standard for wind turbine design, and the loads for this examination are extrapolated from the HAWC2 aeroelastic design code. The concepts are based on a 5 MW off-shore turbine....

  16. New parameters influencing hydraulic runner lifetime

    Science.gov (United States)

    Sabourin, M.; Thibault, D.; Bouffard, D. A.; Lévesque, M.

    2010-08-01

    Traditionally, hydraulic runner mechanical design is based on calculation of static stresses. Today, validation of hydraulic runner design in terms of reliability requires taking into account the fatigue effect of dynamics loads. A damage tolerant approach based on fracture mechanics is the method chosen by Alstom and Hydro-Québec to study fatigue damage in runners. This requires a careful examination of all factors influencing material fatigue behavior. Such material behavior depends mainly on the chemical composition, microstructure and thermal history of the component, and on the resulting residual stresses. Measurement of fracture mechanics properties of various steels have demonstrated that runner lifetime can be significantly altered by differences in the manufacturing process, although remaining in accordance with agreed practices and standards such as ASTM. Carbon content and heat treatment are suspected to influence fatigue lifetime. This will have to be investigated by continuing the current research.

  17. Pilot testing of a hydraulic bridge exciter

    Directory of Open Access Journals (Sweden)

    Andersson Andreas

    2015-01-01

    Full Text Available This paper describes the development of a hydraulic bridge exciter and its first pilot testing on a full scale railway bridge in service. The exciter is based on a hydraulic load cylinder with a capacity of 50 kN and is intended for controlled dynamic loading up to at least 50 Hz. The load is applied from underneath the bridge, enabling testing while the railway line is in service. The system is shown to produce constant load amplitude even at resonance. The exciter is used to experimentally determine frequency response functions at all sensor locations, which serve as valuable input for model updating and verification. An FE-model of the case study bridge has been developed that is in good agreement with the experimental results.

  18. NEW HYDRAULIC ACTUATOR'S POSITION SERVOCONTROL STRATEGY

    Institute of Scientific and Technical Information of China (English)

    KE Zunrong; ZHU Yuquan; LING Xuan

    2007-01-01

    A new hydraulic actuator-hydraulic muscle (HM) is described, and the actuator's features and applications are analyzed, then a position servocontrol system in which HM is main actuator is set up. The mathematical model of the system is built up and several control strategies are discussed. Based on the mathematical model, simulation research and experimental investigation with subsection PID control, neural network self-adaptive PID control and single neuron self-adaptive PID control adopted respectively are carried out, and the results indicate that compared with PID control, neural network self-adaptive PID control and single neuron self-adaptive PID control don't need controlled system's accurate model and have fast response, high control accuracy and strong robustness, they are very suitable for HM position servo control system.

  19. Advanced Hydraulic Studies on Enhancing Particle Removal

    DEFF Research Database (Denmark)

    He, Cheng

    The removal of suspended solids and attached pollutants is one of the main treatment processes in wastewater treatment. This thesis presents studies on the hydraulic conditions of various particle removal facilities for possible ways to increase their treatment capacity and performance by utilizing...... and improving hydraulic conditions. Unlike most traditional theses which usually focus only on one particular subject of study, this thesis contains four relatively independent studies which cover the following topics: a newly proposed particle settling enhancement plate, the redesign of the inlet zone......, introduction and conclusions as well as the study results. All studies were carried out with a combination of numerical model and measurements. In the first part of the thesis a new concept of using a vortex to increase particle removal from liquid was proposed and the new particle settling enhancement plates...

  20. Thermal Hydraulic Design of PWT Accelerating Structures

    CERN Document Server

    Yu, David; Chen Ping; Lundquist, Martin; Luo, Yan

    2005-01-01

    Microwave power losses on the surfaces of accelerating structures will transform to heat which will deform the structures if it is not removed in time. Thermal hydraulic design of the disk and cooling rods of a Plane Wave Transformer (PWT) structure is presented. Experiments to measure the hydraulic (pressure vs flow rate) and cooling (heat removed vs flow rate) properties of the PWT disk are performed, and results compared with simulations using Mathcad models and the COSMOSM code. Both experimental and simulation results showed that the heat deposited on the structure could be removed effectively using specially designed water-cooling circuits and the temperature of the structure could be controlled within the range required.

  1. Hydraulic conductivity and diffusion characterization of GCLs

    Energy Technology Data Exchange (ETDEWEB)

    Mukunoki, T.; Rowe, R.K.; Li, H.M.; Sangam, H.P.; Hurst, P.; Bathurst, R.J. [Queen' s Univ., Kingston, ON (Canada)]|[Royal Military Coll. of Canada, Kingston, ON (Canada); Badv, K. [Urmia Univ. (Iran, Islamic Republic of)

    2003-07-01

    This paper reports on the characterization of the hydraulic conductivity and diffusion of a geosynthetic clay liner (GCL) installed at a site off the southeast coast of Baffin Island, in the Canadian Arctic, following different levels of freeze-thaw exposure and under low temperature conditions. The authors presented a summary of the results obtained for hydraulic conductivity tests on GCLs subjected to freeze-thaw cycles, and specimens permeated with jet fuel (Arctic diesel). They also reported on diffusion tests conducted at 22 Celsius and 5 Celsius, followed by a discussion of the effect of temperature. The results indicate that there is no significant impact on GCL performance due to freeze-thaw cycles, permeation by jet fuel or diffusion at the lower temperatures expected in the north for the short term (up to approximately four years). Additional studies are needed to confirm long term behaviour. 24 refs., 2 tabs., 4 figs.

  2. Thermal-hydraulic analysis of nuclear reactors

    CERN Document Server

    Zohuri, Bahman

    2015-01-01

    This text covers the fundamentals of thermodynamics required to understand electrical power generation systems and the application of these principles to nuclear reactor power plant systems. It is not a traditional general thermodynamics text, per se, but a practical thermodynamics volume intended to explain the fundamentals and apply them to the challenges facing actual nuclear power plants systems, where thermal hydraulics comes to play.  Written in a lucid, straight-forward style while retaining scientific rigor, the content is accessible to upper division undergraduate students and aimed at practicing engineers in nuclear power facilities and engineering scientists and technicians in industry, academic research groups, and national laboratories. The book is also a valuable resource for students and faculty in various engineering programs concerned with nuclear reactors. This book also: Provides extensive coverage of thermal hydraulics with thermodynamics in nuclear reactors, beginning with fundamental ...

  3. IMPACT OF COMBINING MIRROR THERAPY AND HABIT ON HAND GRIP STRENGTH IN CHILDREN WITH HEMIPARESIS

    Directory of Open Access Journals (Sweden)

    Asmaa A. Abo Nour

    2016-08-01

    Full Text Available Background: hemiparetic children usually tend to avoid the use of their impaired arm and are remarkably tend to perform inherently bimanual tasks of daily living with the less impaired arm only rather than with both arms. In fact, these children actually may have never learned to use their impaired arm for certain motor tasks or may only use it in the simplest manner, so the purpose of the study was to determine the impact of combining HABIT and mirror therapy on hand grip in hemiparetic children. Methods: A total of 30 hemiparetic children divided randomly into two groups (A and B of equal number, (N of each =15. Eligibility criteria to our study were age ranged from 4-8 years, ability to score more than 50 % of grasps and associated domains of quality of upper extremity skills test (QUEST and grade 2 in manual ability classification system (MACS, assessment done by baseline hand held dynamometer for hand palmar & pinch grasp strength (in pounds at start (0 week, reassessed at 4 & 8 weeks. The treatment protocol for two groups include: 2 months total time, 3 sessions\\ week, 1.5 hour\\session. Children in study group (A received selected occupational therapy program with modified mirror apparatus while children in control group (B Children received the same occupational therapy program as in study group but without modified mirror apparatus. Results: there is significant improvement in both groups when comparing the pre and post I & II treatment mean values. However comparing the post treatment results of both groups were statistically non-significant. Conclusion: This study confirmed that combining mirror therapy and HABIT is effective in improving hand function.

  4. The Hydraulic Ram (Or Impulse) Pump

    Science.gov (United States)

    Mills, Allan

    2014-01-01

    The hydraulic impulse pump utilizes a fraction of the momentum of a flowing stream to lift a small portion of that water to a higher level. There it may be accumulated in an elevated cistern to provide sufficient water for several families, for the pump works 24 h a day with no additional source of energy. The operation of the pump is described,…

  5. Hydraulic Aspects of Vegetation Maintanence in Streams

    DEFF Research Database (Denmark)

    Larsen, Torben; Vestergaard, Kristian

    1991-01-01

    This paper describes the importance of the underwater vegetation on Danish streams and some of the consequences of vegetation maintenance. the influence of the weed on the hydraulic conditions is studied through experiments in a smaller stream and the effect of cutting channels through the weed...... is measured. A method for predicting the Manning's n as a function of the discharge conditions is suggested, and also a working hypothesis for predictions of the effect of channel cutting is presented....

  6. Rapid Hydraulic Assessment for Stream Restoration

    Science.gov (United States)

    2016-02-01

    account the hydraulic conditions of the stream being restored. This is true whether the project involves a few feet of bank stabilization or several...coefficient, α, expresses a correction for nonuniformity in the velocity distribution, and in most applications this value is assumed to be 1 or read from...a table (e.g., Chow 1959, p.28). The depth and slope angle terms can be replaced by a vertical expression of the depth, y, because in most rivers

  7. Estimation of ground water hydraulic parameters

    Energy Technology Data Exchange (ETDEWEB)

    Hvilshoej, Soeren

    1998-11-01

    The main objective was to assess field methods to determine ground water hydraulic parameters and to develop and apply new analysis methods to selected field techniques. A field site in Vejen, Denmark, which previously has been intensively investigated on the basis of a large amount of mini slug tests and tracer tests, was chosen for experimental application and evaluation. Particular interest was in analysing partially penetrating pumping tests and a recently proposed single-well dipole test. Three wells were constructed in which partially penetrating pumping tests and multi-level single-well dipole tests were performed. In addition, multi-level slug tests, flow meter tests, gamma-logs, and geologic characterisation of soil samples were carried out. In addition to the three Vejen analyses, data from previously published partially penetrating pumping tests were analysed assuming homogeneous anisotropic aquifer conditions. In the present study methods were developed to analyse partially penetrating pumping tests and multi-level single-well dipole tests based on an inverse numerical model. The obtained horizontal hydraulic conductivities from the partially penetrating pumping tests were in accordance with measurements obtained from multi-level slug tests and mini slug tests. Accordance was also achieved between the anisotropy ratios determined from partially penetrating pumping tests and multi-level single-well dipole tests. It was demonstrated that the partially penetrating pumping test analysed by and inverse numerical model is a very valuable technique that may provide hydraulic information on the storage terms and the vertical distribution of the horizontal and vertical hydraulic conductivity under both confined and unconfined aquifer conditions. (EG) 138 refs.

  8. Monitoring hydraulic fracturing with seismic emission volume

    Science.gov (United States)

    Niu, F.; Tang, Y.; Chen, H.; TAO, K.; Levander, A.

    2014-12-01

    Recent developments in horizontal drilling and hydraulic fracturing have made it possible to access the reservoirs that are not available for massive production in the past. Hydraulic fracturing is designed to enhance rock permeability and reservoir drainage through the creation of fracture networks. Microseismic monitoring has been proven to be an effective and valuable technology to image hydraulic fracture geometry. Based on data acquisition, seismic monitoring techniques have been divided into two categories: downhole and surface monitoring. Surface monitoring is challenging because of the extremely low signal-to-noise ratio of the raw data. We applied the techniques used in earthquake seismology and developed an integrated monitoring system for mapping hydraulic fractures. The system consists of 20 to 30 state-of-the-art broadband seismographs, which are generally about hundreds times more sensible than regular geophones. We have conducted two experiments in two basins with very different geology and formation mechanism in China. In each case, we observed clear microseismic events, which may correspond to the induced seismicity directly associated with fracturing and the triggered ones at pre-existing faults. However, the magnitude of these events is generally larger than magnitude -1, approximately one to two magnitudes larger than those detected by downhole instruments. Spectrum-frequency analysis of the continuous surface recordings indicated high seismic energy associated with injection stages. The seismic energy can be back-projected to a volume that surrounds each injection stage. Imaging seismic emission volume (SEV) appears to be an effective way to map the stimulated reservior volume, as well as natural fractures.

  9. Partially decoupled modeling of hydraulic fracturing processes

    Energy Technology Data Exchange (ETDEWEB)

    Settari, A.; Puchyr, P.J.; Bachman, R.C. (Simtech Consulting Services, Calgary (CA))

    1990-02-01

    A new method of partial decoupling of the problem of modeling a hydraulic fracture in a reservoir is described. According to the authors this approach has significant advantages over previous methods with fully coupled or completely uncoupled models. Better accuracy can be achieved in modeling the fracture propagation, and the new system is very efficient and versatile. Virtually any reservoir model can be used for predicting postfracture productivity. Examples of single- and multiphase applications for modeling fractured wells are discussed.

  10. Flow characteristics of variable hydraulic transformer

    Institute of Scientific and Technical Information of China (English)

    杨冠中; 姜继海

    2015-01-01

    A new kind of hydraulic transformer, called variable hydraulic transformer (VHT), is proposed to control its load flow rate. The hydraulic transformer evolves from a pressure transducer to a power transducer. The flow characteristics of VHT, such as its instantaneous flow rates, average flow rates, and flow pulsations in the ports, are investigated. Matlab software is used to simulate and calculate. There are five controlled angles of the port plate that can help to define the flow characteristics of VHT. The relationships between the flow characteristics and the structure in VHT are shown. Also, the plus−minus change of the average flow rates and the continuity of the instantaneous flow rates in the ports are presented. The results demonstrate the performance laws of VHT when the controlled angles of the port plate and of the swash plate change. The results also reveal that the special principle of the flow pulsation in the ports and the jump points of the instantaneous curves are the two basic causes of its loud noise, and that the control angles of the port plate and the swash plate and the pressures in the ports are the three key factors of the noise.

  11. Measuring Disturbance Impact on Soil Hydraulic Properties

    Science.gov (United States)

    Hinshaw, S.; Mirus, B. B.

    2014-12-01

    Disturbances associated with land cover change such as forest clearing and mono-cropping can have a substantial impact on soil-hydraulic properties, which in turn have a cascading impact on surface and near-surface hydrologic response. Although disturbances and vegetation change can alter soil-water retention and conductivity relations, hydrologic models relying on traditional soil-texture based pedotransfer functions would not be able to capture the disturbance impact on infiltration and soil-moisture storage. Therefore, in-situ estimates of characteristic curves of soil water retention and hydraulic conductivity relations are needed to understand and predict hydrologic impacts of land cover change. We present a method for in-situ estimates of effective characteristic curves that capture hysteretic soil-water retention properties at the plot scale. We apply this method to two different forest treatments and in urban settings to investigate the impact of land-use disturbances on soil-hydraulic properties. We compare our in-situ estimation method to results for simple pedotransfer functions to illustrate how this approach can improve understanding of disturbance impacts on hydrologic processes and function.

  12. On the Dynamic Measurements of Hydraulic Characteristics

    Science.gov (United States)

    Hasmatuchi, Vlad; Bosioc, Alin; Münch-Alligné, Cécile

    2016-11-01

    The present work introduces the implementation and validation of a faster method to measure experimentally the efficiency characteristics of hydraulic turbomachines at a model scale on a test rig. The case study is represented by a laboratory prototype of an in-line axial microturbine for water supply networks. The 2.65 kW one-stage variable speed turbine, composed by one upstream 5-blade runner followed by one counter-rotating downstream 7-blade runner, has been installed on the HES-SO Valais/Wallis universal test rig dedicated to assess performances of small hydraulic machinery following the IEC standard recommendations. In addition to the existing acquisition/control system of the test rig used to measure the 3D hill-chart of a turbine by classical static point-by-point method, a second digitizer has been added to acquire synchronized dynamic signals of the employed sensors. The optimal acceleration/deceleration ramps of the electrical drives have been previously identified in order to cope with the purpose of a reduced measurement time while avoiding errors and hysteresis on the acquired hydraulic characteristics. Finally, the comparison between the turbine efficiency hill-charts obtained by dynamic and static point-by-point methods shows a very good agreement in terms of precision and repeatability. Moreover, the applied dynamic method reduces significantly (by a factor of up to ten) the time necessary to measure the efficiency characteristics on model testing.

  13. Hands-On Bulletin Boards.

    Science.gov (United States)

    Henneman, Dawn

    1984-01-01

    Patterns and directions are given for making bulletin boards that teach language arts and mathematics skills through hands-on student involvement. The boards help teach multiplication tables, word contractions, letter sounds, homonyms, compound words, alphabetization, and other skills. (PP)

  14. Arthritis of the hand - Rheumatoid

    Science.gov (United States)

    ... Media Find a Hand Surgeon Home Anatomy Rheumatoid Arthritis Email to a friend * required fields From * To * DESCRIPTION In its most literal sense, arthritis means “inflamed joint.” Arthritis describes any condition where ...

  15. Neural bases of hand synergies.

    Science.gov (United States)

    Santello, Marco; Baud-Bovy, Gabriel; Jörntell, Henrik

    2013-01-01

    The human hand has so many degrees of freedom that it may seem impossible to control. A potential solution to this problem is "synergy control" which combines dimensionality reduction with great flexibility. With applicability to a wide range of tasks, this has become a very popular concept. In this review, we describe the evolution of the modern concept using studies of kinematic and force synergies in human hand control, neurophysiology of cortical and spinal neurons, and electromyographic (EMG) activity of hand muscles. We go beyond the often purely descriptive usage of synergy by reviewing the organization of the underlying neuronal circuitry in order to propose mechanistic explanations for various observed synergy phenomena. Finally, we propose a theoretical framework to reconcile important and still debated concepts such as the definitions of "fixed" vs. "flexible" synergies and mechanisms underlying the combination of synergies for hand control.

  16. American Association for Hand Surgery

    Science.gov (United States)

    ... Hand Care Provider Connect With Us: Notice Regarding Hurricane Irma and Hurricane Maria in Puerto Rico The AAHS ... closely monitoring the situation in Puerto Rico following Hurricane Irma and Hurricane Maria. Leadership and staff have been ...

  17. American Society of Hand Therapists

    Science.gov (United States)

    ... there is brush and fuel for the fire. Residence in the area next to these foothills (like ... Hope Orthopedics - Salem, OR CHT/Hand Therapist - Duke University Hospital - Adult Ambulatory Division PT/OT - Durham, NC ...

  18. Hands-On Bulletin Boards.

    Science.gov (United States)

    Henneman, Dawn

    1984-01-01

    Patterns and directions are given for making bulletin boards that teach language arts and mathematics skills through hands-on student involvement. The boards help teach multiplication tables, word contractions, letter sounds, homonyms, compound words, alphabetization, and other skills. (PP)

  19. Principles of Hand Fracture Management

    Science.gov (United States)

    Haughton, DN; Jordan, D; Malahias, M; Hindocha, S; Khan, W

    2012-01-01

    The hand is essential in humans for physical manipulation of their surrounding environment. Allowing the ability to grasp, and differentiated from other animals by an opposing thumb, the main functions include both fine and gross motor skills as well as being a key tool for sensing and understanding the immediate surroundings of their owner. Hand fractures are the most common fractures presenting at both accident and emergency and within orthopaedic clinics. Appropriate evaluation at first presentation, as well as during their management, can significantly prevent both morbidity and disability to a patient. These decisions are dependant on a wide range of factors including age, hand dominance, occupation and co-morbidities. A fracture is best described as a soft tissue injury with an associated bony injury. Despite this being the case, this paper intends to deal mainly with the bone injury and aims to discuss both the timing, as well as the methods available, of hand fracture management. PMID:22423303

  20. Determining the Conditions for the Hydraulic Impacts Emergence at Hydraulic Systems

    Directory of Open Access Journals (Sweden)

    Mazurenko A.S.

    2017-08-01

    Full Text Available This research aim is to develop a method for modeling the conditions for the critical hydrau-lic impacts emergence on thermal and nuclear power plants’ pipeline systems pressure pumps depart-ing from the general provisions of the heat and hydrodynamic instability theory. On the developed method basis, the conditions giving rise to the reliability-critical hydraulic impacts emergence on pumps for the thermal and nuclear power plants’ typical pipeline system have been determined. With the flow characteristic minimum allowable (critical sensitivity, the flow velocity fluctuations ampli-tude reaches critical values at which the pumps working elements’ failure occurs. The critical hydrau-lic impacts emergence corresponds to the transition of the vibrational heat-hydrodynamic instability into an aperiodic one. As research revealed, a highly promising approach as to the preventing the criti-cal hydraulic impacts related to the foreground use of pumps having the most sensitive consumption (at supply network performance (while other technical characteristics corresponding to that parame-ter. The research novelty refers to the suggested method elaborated by the authors’ team, which, in contrast to traditional approaches, is efficient in determining the pump hydraulic impact occurrence conditions when the vibrational heat-hydrodynamic instability transition to the aperiodic instability.

  1. Rapid hydraulic recovery in Eucalyptus pauciflora after drought: linkages between stem hydraulics and leaf gas exchange.

    Science.gov (United States)

    Martorell, Sebastià; Diaz-Espejo, Antonio; Medrano, Hipólito; Ball, Marilyn C; Choat, Brendan

    2014-03-01

    In woody plants, photosynthetic capacity is closely linked to rates at which the plant hydraulic system can supply water to the leaf surface. Drought-induced embolism can cause sharp declines in xylem hydraulic conductivity that coincide with stomatal closure and reduced photosynthesis. Recovery of photosynthetic capacity after drought is dependent on restored xylem function, although few data exist to elucidate this coordination. We examined the dynamics of leaf gas exchange and xylem function in Eucalyptus pauciflora seedlings exposed to a cycle of severe water stress and recovery after re-watering. Stomatal closure and leaf turgor loss occurred at water potentials that delayed the extensive spread of embolism through the stem xylem. Stem hydraulic conductance recovered to control levels within 6 h after re-watering despite a severe drought treatment, suggesting an active mechanism embolism repair. However, stomatal conductance did not recover after 10 d of re-watering, effecting tighter control of transpiration post drought. The dynamics of recovery suggest that a combination of hydraulic and non-hydraulic factors influenced stomatal behaviour post drought.

  2. Hand gestures mouse cursor control

    Directory of Open Access Journals (Sweden)

    Marian-Avram Vincze

    2014-05-01

    Full Text Available The paper describes the implementation of a human-computer interface for controlling the mouse cursor. The test reveal the fact: a low-cost web camera some processing algorithms are quite enough to control the mouse cursor on computers. Even if the system is influenced by the illuminance level on the plane of the hand, the current study may represent a start point for some studies on the hand tracking and gesture recognition field.

  3. Hand, Foot, and Mouth Disease

    Centers for Disease Control (CDC) Podcasts

    2013-08-08

    Hand, foot, and mouth disease is a contagious illness that mainly affects children under five. In this podcast, Dr. Eileen Schneider talks about the symptoms of hand, foot, and mouth disease, how it spreads, and ways to help protect yourself and your children from getting infected with the virus.  Created: 8/8/2013 by National Center for Immunization and Respiratory Diseases (NCIRD).   Date Released: 8/8/2013.

  4. Hand function after nerve repair.

    OpenAIRE

    Lundborg, Göran; Rosén, Birgitta

    2007-01-01

    Treatment of injuries to major nerve trunks in the hand and upper extremity remains a major and challenging reconstructive problem. Such injuries may cause long-lasting disabilities in terms of lost fine sensory and motor functions. Nowadays there is no surgical repair technique that can ensure recovery of tactile discrimination in the hand of an adult patient following nerve repair while very young individuals usually regain a complete recovery of functional sensibility. Post-traumatic nerve...

  5. Replantation (Finger, Hand, or Arm)

    Science.gov (United States)

    ... per month. The number of inches from the injury to the tip of a finger gives the minimum number of months after which ... Replantation refers to the surgical reattachment of a finger, hand, or arm that has been completely cut from a person’s ... 2017 by American Society for Surgery of the Hand × Search Tips Tip 1: Start with the basics like "carpal ...

  6. The Rubber Hand Illusion: feeling of ownership and proprioceptive drift do not go hand in hand.

    Science.gov (United States)

    Rohde, Marieke; Di Luca, Massimiliano; Ernst, Marc O

    2011-01-01

    In the Rubber Hand Illusion, the feeling of ownership of a rubber hand displaced from a participant's real occluded hand is evoked by synchronously stroking both hands with paintbrushes. A change of perceived finger location towards the rubber hand (proprioceptive drift) has been reported to correlate with this illusion. To measure the time course of proprioceptive drift during the Rubber Hand Illusion, we regularly interrupted stroking (performed by robot arms) to measure perceived finger location. Measurements were made by projecting a probe dot into the field of view (using a semi-transparent mirror) and asking participants if the dot is to the left or to the right of their invisible hand (Experiment 1) or to adjust the position of the dot to that of their invisible hand (Experiment 2). We varied both the measurement frequency (every 10 s, 40 s, 120 s) and the mode of stroking (synchronous, asynchronous, just vision). Surprisingly, with frequent measurements, proprioceptive drift occurs not only in the synchronous stroking condition but also in the two control conditions (asynchronous stroking, just vision). Proprioceptive drift in the synchronous stroking condition is never higher than in the just vision condition. Only continuous exposure to asynchronous stroking prevents proprioceptive drift and thus replicates the differences in drift reported in the literature. By contrast, complementary subjective ratings (questionnaire) show that the feeling of ownership requires synchronous stroking and is not present in the asynchronous stroking condition. Thus, subjective ratings and drift are dissociated. We conclude that different mechanisms of multisensory integration are responsible for proprioceptive drift and the feeling of ownership. Proprioceptive drift relies on visuoproprioceptive integration alone, a process that is inhibited by asynchronous stroking, the most common control condition in Rubber Hand Illusion experiments. This dissociation implies that

  7. The Rubber Hand Illusion: feeling of ownership and proprioceptive drift do not go hand in hand.

    Directory of Open Access Journals (Sweden)

    Marieke Rohde

    Full Text Available In the Rubber Hand Illusion, the feeling of ownership of a rubber hand displaced from a participant's real occluded hand is evoked by synchronously stroking both hands with paintbrushes. A change of perceived finger location towards the rubber hand (proprioceptive drift has been reported to correlate with this illusion. To measure the time course of proprioceptive drift during the Rubber Hand Illusion, we regularly interrupted stroking (performed by robot arms to measure perceived finger location. Measurements were made by projecting a probe dot into the field of view (using a semi-transparent mirror and asking participants if the dot is to the left or to the right of their invisible hand (Experiment 1 or to adjust the position of the dot to that of their invisible hand (Experiment 2. We varied both the measurement frequency (every 10 s, 40 s, 120 s and the mode of stroking (synchronous, asynchronous, just vision. Surprisingly, with frequent measurements, proprioceptive drift occurs not only in the synchronous stroking condition but also in the two control conditions (asynchronous stroking, just vision. Proprioceptive drift in the synchronous stroking condition is never higher than in the just vision condition. Only continuous exposure to asynchronous stroking prevents proprioceptive drift and thus replicates the differences in drift reported in the literature. By contrast, complementary subjective ratings (questionnaire show that the feeling of ownership requires synchronous stroking and is not present in the asynchronous stroking condition. Thus, subjective ratings and drift are dissociated. We conclude that different mechanisms of multisensory integration are responsible for proprioceptive drift and the feeling of ownership. Proprioceptive drift relies on visuoproprioceptive integration alone, a process that is inhibited by asynchronous stroking, the most common control condition in Rubber Hand Illusion experiments. This dissociation implies

  8. Bimanual-vertical hand movements.

    Science.gov (United States)

    Kwon, Jay C; Cohen, Matthew L; Williamson, John; Burtis, Brandon; Heilman, Kenneth M

    2011-07-01

    Patients often demonstrate attentional and action-intentional biases in both the transverse and coronal planes. In addition, when making forelimb movements in the transverse plane, normal participants also have spatial and magnitude asymmetries, but forelimb spatial asymmetries have not been studied in coronal space. Thus, to learn if when normal people make vertical movements they have right-left spatial and magnitude biases, seventeen healthy, blindfolded volunteers had their hands (holding pens) placed vertically in their midsagittal plane, 10 inches apart, on pieces of paper positioned above, below, and at eye-level. Participants were asked to move their hands together vertically and meet in the middle. Participants demonstrated less angular deviation in the below-eye condition than in the other spatial conditions, when moving down than up, and with their right than left hand. Movements toward eye level from upper or lower space were also more accurate than movements in the other directions. Independent of hand, lines were longer with downward than upward movements and the right hand moved more distance than the left. These attentional-intentional asymmetries may be related to gravitational force, hand-hemispheric dominance, and spatial "where" asymmetries; however, the mechanisms accounting for these asymmetries must be ascertained by future research.

  9. Predicting the impact of biochar additions on soil hydraulic properties

    Science.gov (United States)

    Spokas, Kurt; Lim, Tae Jun; Feyereisen, Gary; Novak, Jeff

    2015-04-01

    Different physical and chemical properties of biochar, which is made out of a variety of biomass materials, can impact water movement through amended soil. The objective of this research was to develop a decision support tool predicting the impact of biochar additions on soil saturated hydraulic conductivity (Ksat). Four different kinds of biochar were added to four different textured soils (coarse sand, fine sand, loam, and clay texture) to assess these effects at the rates of 0, 1, 2, and 5 % (w/w). The Ksat of the biochar amended soils were significantly influenced by the rate and type of biochar, as well as the original particle size of soil. The Ksat decreased when biochar was added to coarse and fine sands. Biochar with larger particles sizes (60%; >1 mm) decreased Ksat to a larger degree than the smaller particle size biochar (60%; soils. Increasing tortuosity in the amended sandy soil could explain this behavior. On the other hand, for the clay loam 1% and 2% biochar additions universally increased the Ksat with higher biochar amounts providing no further alterations. The developed model utilizes soil texture pedotransfer functions for predicting agricultural soil Ksat as a function of soil texture. The model accurately predicted the direction of the Ksat influence, even though the exact magnitude still requires further refinement.

  10. Investigation of a hydraulic impact: a technology in rock breaking

    CERN Document Server

    Genet, Martin; Tran-Cong, Thanh

    2009-01-01

    The finite element method and dimensional analysis have been applied in the present paper to study a hydraulic impact, which is utilized in a non-explosive rock breaking technology in mining industry. The impact process of a high speed piston on liquid water, previously introduced in a borehole drilled in rock, is numerically simulated. The research is focused on the influences of all the parameters involved in the technology on the largest principal stress in the rock, which is considered as one of the key factors to break the rock. Our detailed parametric investigation reveals that the variation of the isotropic rock material properties, especially its density, has no significant influence on the largest principal stress. The influences of the depth of the hole and the depth of the water column are also very small. On the other hand, increasing the initial kinetic energy of the piston can dramatically increase the largest principal stress and the best way to increase the initial kinetic energy of the piston...

  11. FOREWORD: The XXV IAHR Symposium on Hydraulic Machinery and Systems marks half a century tradition

    Science.gov (United States)

    Susan-Resiga, Romeo

    2010-05-01

    'Politehnica' of Timisoara in 1923 'It is not the walls that make a school, but the spirit living inside'. A particular trademark of the 'Politehnica' of Timisoara was the continuous effort to answer industrial problems by training the students not only on theoretical aspects but also in design and manufacturing, as well as in laboratory works. Developing modern laboratories, where students can observe and understand first hand the engineering applications along the years a priority for Timisoara 'Politehnica' University. The School of Hydraulic Machinery within the 'Politehnica' University of Timisoara was established in early 1930 by Professor Aurel Barglazan (1905-1960), and further developed by Professor Ioan Anton (born 1924), both members of the Romanian Academy. The Laboratory of Hydraulic Machines from Timisoara (LMHT) started back in 1928 in a small hut, with a test rig for Francis and Kaplan turbines manufactured by J M Voith. LMHT was continuously developed and was officially recognized in 1959 as being one of the leading research and developing laboratories in Romania. It was the foundation of the Romanian efforts of designing and manufacturing hydraulic turbines starting in 1960 at the Resita Machine Building Factory. Under the leadership of Professor Ioan Anton, the Timisoara School in Hydraulic Machinery has focused the basic and development research activities on the following main topics: (i) Turbine Hydrodynamics, (ii) Hydrofoil Cascade Hydrodynamics, (iii) Cavitation in Hydraulic Machines and Equipments, (iv) Scale-up Effects in Hydraulic Machines. With the establishment in the year 2000 of the National Center for Engineering of Systems with Complex Fluids, within the 'Politehnica' University of Timisoara, the research in turbomachinery hydrodynamics and cavitation included high performance computing for flows in hydraulic machines, as well as the development of novel technologies to mitigate the self-induced flow instabilities in hydraulic turbines operated

  12. Multivariate distributions of soil hydraulic parameters

    Science.gov (United States)

    Qu, Wei; Pachepsky, Yakov; Huisman, Johan Alexander; Martinez, Gonzalo; Bogena, Heye; Vereecken, Harry

    2014-05-01

    Statistical distributions of soil hydraulic parameters have to be known when synthetic fields of soil hydraulic properties need to be generated in ensemble modeling of soil water dynamics and soil water content data assimilation. Pedotransfer functions that provide statistical distributions of water retention and hydraulic conductivity parameters for textural classes are most often used in the parameter field generation. Presence of strong correlations can substantially influence the parameter generation results. The objective of this work was to review and evaluate available data on correlations between van Genuchten-Mualem (VGM) model parameters. So far, two different approaches were developed to estimate these correlations. The first approach uses pedotransfer functions to generate VGM parameters for a large number of soil compositions within a textural class, and then computes parameter correlations for each of the textural classes. The second approach computes the VGM parameter correlations directly from parameter values obtained by fitting VGM model to measured water retention and hydraulic conductivity data for soil samples belonging to a textural class. Carsel and Parish (1988) used the Rawls et al. (1982) pedotransfer functions, and Meyer et al. (1997) used the Rosetta pedotransfer algorithms (Schaap, 2002) to develop correlations according to the first approach. We used the UNSODA database (Nemes et al. 2001), the US Southern Plains database (Timlin et al., 1999), and the Belgian database (Vereecken et al., 1989, 1990) to apply the second approach. A substantial number of considerable (>0.7) correlation coefficients were found. Large differences were encountered between parameter correlations obtained with different approaches and different databases for the same textural classes. The first of the two approaches resulted in generally higher values of correlation coefficients between VGM parameters. However, results of the first approach application depend

  13. Parameter Estimation Technique of Nonlinear Prosthetic Hand System

    Directory of Open Access Journals (Sweden)

    M.H.Jali

    2016-10-01

    Full Text Available This paper illustrated the parameter estimation technique of motorized prosthetic hand system. Prosthetic hands have become importance device to help amputee to gain a normal functional hand. By integrating various types of actuators such as DC motor, hydraulic and pneumatic as well as mechanical part, a highly useful and functional prosthetic device can be produced. One of the first steps to develop a prosthetic device is to design a control system. Mathematical modeling is derived to ease the control design process later on. This paper explained the parameter estimation technique of a nonlinear dynamic modeling of the system using Lagrangian equation. The model of the system is derived by considering the energies of the finger when it is actuated by the DC motor. The parameter estimation technique is implemented using Simulink Design Optimization toolbox in MATLAB. All the parameters are optimized until it achieves a satisfactory output response. The results show that the output response of the system with parameter estimation value produces a better response compare to the default value

  14. Analysis of Innovative Design of Energy Efficient Hydraulic Actuators

    Directory of Open Access Journals (Sweden)

    M Osman Abdalla

    2013-01-01

    Full Text Available Hydraulic cylinder actuators are used extensively in industrial, construction and agricultural works. The small sized outlet ports of the cylinders resist the flow of discharged oil; and as a result the piston motion is slowed down. This causes a lot of heat generation and energy loss within the actuators. The study investigates and analyzes the possibilities of reducing the hydraulic resistance and increasing efficiency of the hydraulic actuator. Conventional hydraulic cylinders are simulated in FLUENT. Results show that the small outlet ports are the sources of energy loss in hydraulic cylinders. A new hydraulic system was proposed as a solution to relieve the hydraulic resistance in the actuators. The proposed system is a four ports hydraulic cylinder fitted with a novel flow control valve. The proposed four ports cylinder was simulated and parameters such as ports sizes, loads and pressures are varied during the simulation. The hydraulic resisting forces, piston speed and mass flow rates are computed. Results show that the hydraulic resistance is significantly reduced in the proposed four ports actuators; and the proposed cylinders run faster than the conventional cylinders and a considerable amount of energyis saved as well.

  15. Variation in reach-scale hydraulic conductivity of streambeds

    Science.gov (United States)

    Stewardson, M. J.; Datry, T.; Lamouroux, N.; Pella, H.; Thommeret, N.; Valette, L.; Grant, S. B.

    2016-04-01

    Streambed hydraulic conductivity is an important control on flow within the hyporheic zone, affecting hydrological, ecological, and biogeochemical processes essential to river ecosystem function. Despite many published field measurements, few empirical studies examine the drivers of spatial and temporal variations in streambed hydraulic conductivity. Reach-averaged hydraulic conductivity estimated for 119 surveys in 83 stream reaches across continental France, even of coarse bed streams, are shown to be characteristic of sand and finer sediments. This supports a model where processes leading to the accumulation of finer sediments within streambeds largely control hydraulic conductivity rather than the size of the coarse bed sediment fraction. After describing a conceptual model of relevant processes, we fit an empirical model relating hydraulic conductivity to candidate geomorphic and hydraulic drivers. The fitted model explains 72% of the deviance in hydraulic conductivity (and 30% using an external cross-validation). Reach hydraulic conductivity increases with the amplitude of bedforms within the reach, the bankfull channel width-depth ratio, stream power and upstream catchment erodibility but reduces with time since the last streambed disturbance. The correlation between hydraulic conductivity and time since a streambed mobilisation event is likely a consequence of clogging processes. Streams with a predominantly suspended load and less frequent streambed disturbances are expected to have a lower streambed hydraulic conductivity and reduced hyporheic fluxes. This study suggests a close link between streambed sediment transport dynamics and connectivity between surface water and the hyporheic zone.

  16. Geostatistical Estimations of Regional Hydraulic Conductivity Fields

    Science.gov (United States)

    Patriarche, D.; Castro, M. C.; Goovaerts, P.

    2004-12-01

    Direct and indirect measurements of hydraulic conductivity (K) are commonly performed, providing information on the magnitude of this parameter at the local scale (tens of centimeters to hundreds of meters) and at shallow depths. By contrast, field information on hydraulic conductivities at regional scales of tens to hundreds of kilometers and at greater depths is relatively scarce. Geostatistical methods allow for sparsely sampled observations of a variable (primary information) to be complemented by a more densely sampled secondary attribute. Geostatistical estimations of the hydraulic conductivity field in the Carrizo aquifer, a major groundwater flow system extending along Texas, are performed using available primary (e.g., transmissivity, hydraulic conductivity) and secondary (specific capacity) information, for depths up to 2.2 km, and over three regional domains of increasing extent: 1) the domain corresponding to a three-dimensional groundwater flow model previously built (model domain); 2) the area corresponding to the ten counties encompassing the model domain (County domain), and; 3) the full extension of the Carrizo aquifer within Texas (Texas domain). Two different approaches are used: 1) an indirect approach are transmissivity (T) is estimated first and (K) is retrieved through division of the T estimate by the screening length of the wells, and; 2) a direct approach where K data are kriged directly. Prediction performances of the tested geostatistical procedures (kriging combined with linear regression, kriging with known local means, kriging of residuals, and cokriging) are evaluated through cross validation for both log-transformed variables and back-transformed ones. For the indirect approach, kriging of log T residuals yields the best estimates for both log-transformed and back-transformed variables in the model domain. For larger regional scales (County and Texas domains), cokriging performs generally better than univariate kriging procedures

  17. Modeling biofilm dynamics and hydraulic properties in variably saturated soils using a channel network model

    Science.gov (United States)

    Rosenzweig, Ravid; Furman, Alex; Dosoretz, Carlos; Shavit, Uri

    2014-07-01

    Biofilm effects on water flow in unsaturated environments have largely been ignored in the past. However, intensive engineered systems that involve elevated organic loads such as wastewater irrigation, effluent recharge, and bioremediation processes make understanding how biofilms affect flow highly important. In the current work, we present a channel-network model that incorporates water flow, substrate transport, and biofilm dynamics to simulate the alteration of soil hydraulic properties, namely water retention and conductivity. The change in hydraulic properties due to biofilm growth is not trivial and depends highly on the spatial distribution of the biofilm development. Our results indicate that the substrate mass transfer coefficient across the water-biofilm interface dominates the spatiotemporal distribution of biofilm. High mass transfer coefficients lead to uncontrolled biofilm growth close to the substrate source, resulting in preferential clogging of the soil. Low mass transfer coefficients, on the other hand, lead to a more uniform biofilm distribution. The first scenario leads to a dramatic reduction of the hydraulic conductivity with almost no change in water retention, whereas the second scenario has a smaller effect on conductivity but a larger influence on retention. The current modeling approach identifies key factors that still need to be studied and opens the way for simulation and optimization of processes involving significant biological activity in unsaturated soils.

  18. Review of Hydraulic Fracturing for Preconditioning in Cave Mining

    Science.gov (United States)

    He, Q.; Suorineni, F. T.; Oh, J.

    2016-12-01

    Hydraulic fracturing has been used in cave mining for preconditioning the orebody following its successful application in the oil and gas industries. In this paper, the state of the art of hydraulic fracturing as a preconditioning method in cave mining is presented. Procedures are provided on how to implement prescribed hydraulic fracturing by which effective preconditioning can be realized in any in situ stress condition. Preconditioning is effective in cave mining when an additional fracture set is introduced into the rock mass. Previous studies on cave mining hydraulic fracturing focused on field applications, hydraulic fracture growth measurement and the interaction between hydraulic fractures and natural fractures. The review in this paper reveals that the orientation of the current cave mining hydraulic fractures is dictated by and is perpendicular to the minimum in situ stress orientation. In some geotechnical conditions, these orientation-uncontrollable hydraulic fractures have limited preconditioning efficiency because they do not necessarily result in reduced fragmentation sizes and a blocky orebody through the introduction of an additional fracture set. This implies that if the minimum in situ stress orientation is vertical and favors the creation of horizontal hydraulic fractures, in a rock mass that is already dominated by horizontal joints, no additional fracture set is added to that rock mass to increase its blockiness to enable it cave. Therefore, two approaches that have the potential to create orientation-controllable hydraulic fractures in cave mining with the potential to introduce additional fracture set as desired are proposed to fill this gap. These approaches take advantage of directional hydraulic fracturing and the stress shadow effect, which can re-orientate the hydraulic fracture propagation trajectory against its theoretical predicted direction. Proppants are suggested to be introduced into the cave mining industry to enhance the

  19. Hydrodynamic evaluation of a hydraulic clarifier through hydraulic behaviour indicators and simplified flow models

    Directory of Open Access Journals (Sweden)

    Paola Patiño

    2012-04-01

    Full Text Available Hydrodynamic phenomena take place within water treatment plants associated with physical, operational and environmental factors which can affect the water quality. This study evaluated a hydraulic clarifier’s hydrodynamic pattern using sludge recirculation through continuous tracer test leading to determining hydraulic behaviour indicators and simplified flow models. The clarifier had dual flow with a predominantly complete mixture during the hours in which higher temperatures were reported for affluent water compared to those reported inside the reactor, causing the formation of density currents promoting mixing in the reactor and increased turbidity in the effluent. The hydraulic indicators and the Wolf-Resnick model had higher sensitivity to the influence of temperature on reactor hydrodynamics.

  20. Power Management in Mobile Hydraulic Applications - An Approach for Designing Hydraulic Power Supply Systems

    DEFF Research Database (Denmark)

    Pedersen, Henrik Clemmensen

    2004-01-01

    in a project to develop rules and methods for designing and controlling mobile hydraulic systems in the most energy efficient way, when also considering the operational aspects of the system. The paper first describes the thoughts and ideas behind the project and then focus on an automated approach to design......Throughout the last three decades energy consumption has become one of the primary design aspects in hydraulic systems, especially for mobile hydraulic systems, as power and cooling capacity here is at limited disposal. Considering the energy usage, this is dependent on component efficiency......, but even more important is the system topology. However, there are no rules or guidelines for what system topology to choose for a given application, in order to obtain the most energy efficient system, nor for how the energy should be distributed in the system. This paper describes the approach taken...

  1. [Is there any correlation between the strength of pronation and supination of the dominant hand and that of the non-dominant one in right-handed healthy adults: preliminary results].

    Science.gov (United States)

    Rey, P-B; Jardin, E; Uhring, J; Obert, L

    2014-02-01

    We searched the existence of a link between the strength of pronation and supination of the dominant forearm and those of the non-dominant one. Ninety-seven volunteers were tested in pronation and supination with an analog dynamometer. Gender, age, dominance, height and weight were recorded. The measurement position was: 90° of elbow flexion, 0° of shoulder abduction, wrist slightly extended and neutral pronation-supination. We took four measurements per patient: strength in pronation and supination, in both the dominant and non-dominant sides. Fifteen subjects were evaluated twice. The left-handed (4) were removed from the statistical analysis. There were 38 men (37 years, 18-66) and 55 women (45 years, 21-71). Torques were higher (P0.6). Relating to the 15 subjects evaluated twice, the value of the forces varied during the day, but the ratio "non-dominant/dominant" was constant. The left-handed people were excluded, their values may be different from those of right-handers, as has been shown for grip strength. There was a strength variation during the day, but the ratio "non-dominant/dominant" was constant, making it more relevant intra-individual comparison (non-dominant side versus dominant side) rather inter-individual (based on charts of gender, age, weight and height). In the right-handed, the ratio "strength non-dominant side/dominant" is constant, defining easily in consultation the expected value of recovery of an injured forearm.

  2. Derivation of site-specific relationships between hydraulic parameters and p-wave velocities based on hydraulic and seismic tomography

    Energy Technology Data Exchange (ETDEWEB)

    Brauchler, R.; Doetsch, J.; Dietrich, P.; Sauter, M.

    2012-01-10

    In this study, hydraulic and seismic tomographic measurements were used to derive a site-specific relationship between the geophysical parameter p-wave velocity and the hydraulic parameters, diffusivity and specific storage. Our field study includes diffusivity tomograms derived from hydraulic travel time tomography, specific storage tomograms, derived from hydraulic attenuation tomography, and p-wave velocity tomograms, derived from seismic tomography. The tomographic inversion was performed in all three cases with the SIRT (Simultaneous Iterative Reconstruction Technique) algorithm, using a ray tracing technique with curved trajectories. The experimental set-up was designed such that the p-wave velocity tomogram overlaps the hydraulic tomograms by half. The experiments were performed at a wellcharacterized sand and gravel aquifer, located in the Leine River valley near Göttingen, Germany. Access to the shallow subsurface was provided by direct-push technology. The high spatial resolution of hydraulic and seismic tomography was exploited to derive representative site-specific relationships between the hydraulic and geophysical parameters, based on the area where geophysical and hydraulic tests were performed. The transformation of the p-wave velocities into hydraulic properties was undertaken using a k-means cluster analysis. Results demonstrate that the combination of hydraulic and geophysical tomographic data is a promising approach to improve hydrogeophysical site characterization.

  3. Hand infections: a retrospective analysis

    Directory of Open Access Journals (Sweden)

    Tolga Türker

    2014-09-01

    Full Text Available Purpose. Hand infections are common, usually resulting from an untreated injury. In this retrospective study, we report on hand infection cases needing surgical drainage in order to assess patient demographics, causation of infection, clinical course, and clinical management.Methods. Medical records of patients presenting with hand infections, excluding post-surgical infections, treated with incision and debridement over a one-year period were reviewed. Patient demographics; past medical history; infection site(s and causation; intervals between onset of infection, hospital admission, surgical intervention and days of hospitalization; gram stains and cultures; choice of antibiotics; complications; and outcomes were reviewed.Results. Most infections were caused by laceration and the most common site of infection was the palm or dorsum of the hand. Mean length of hospitalization was 6 days. Methicillin-resistant Staphylococcus aureus, beta-hemolytic Streptococcus and methicillin-susceptible Staphylococcus aureus were the most commonly cultured microorganisms. Cephalosporins, clindamycin, amoxicillin/clavulanate, penicillin, vancomycin, and trimethoprim/sulfamethoxazole were major antibiotic choices. Amputations and contracture were the primary complications.Conclusions. Surgery along with medical management were key to treatment and most soft tissue infections resolved without further complications. With prompt and appropriate care, most hand infection patients can achieve full resolution of their infection.

  4. [Reliability and validity of the analysis of hand grip and pinch force in isometric and isokinetic conditions].

    Science.gov (United States)

    Benaglia, P G; Franchignoni, F; Ferriero, G; Zebellin, G; Sartorio, F

    1999-01-01

    Strength measurement of the hand grip is at the core of most protocols of functional assessment of the upper limb and in rehabilitation plays a major role in the analysis of treatment efficacy and patients' occupational ability. The aims of this study were to: a) verify the repeatability of strength measurements made during performance of the hand grip and three types of pinch, carried out under isometric and isokinetic conditions; b) compare maximal isometric strength with the corresponding isokinetic value for each of the manoeuvres studied; c) investigate the correlations between the strength expressed in the different manoeuvres, under both isometric and isokinetic conditions. We studied 14 voluntary subjects over three sessions conducted at 48-hr intervals, employing a computerized isokinetic dynamometer Lido WorkSet equipped with device N(o) 21 for the study of pinch (lateral pinch, pulp pinch, chuck pinch) and device N(o) 52 for the grip study. Isometric contractions resulted stronger than isokinetic ones, and the hand grip was found to be the manoeuvre able to produce most strength. The repeatability of each strength measurement test over the three days was high (Intraclass Correlation Coefficients: 0.89-0.93). Correlations between the isometric and isokinetic performance for each of the manoeuvres examined were always high (Pearson's r coefficients: 0.89-0.95) as were those between the different manoeuvres, whether performed in isometric or isokinetic modality (r: 0.60-0.94).

  5. Effect of muscle strength and pain on hand function in patients with trapeziometacarpal osteoarthritis. A cross-sectional study.

    Science.gov (United States)

    Cantero-Téllez, Raquel; Martín-Valero, Rocío; Cuesta-Vargas, Antonio

    2015-01-01

    To assess the relationship between muscle strength (Jama), and pain (VAS) levels with hand function (DASH) in patients with trapeziometarcapal osteoarthritis. Cross-sectional study. Sample of 72 patients with osteoarthritis stage 2-3 (Eaton) and trapeziometacarpal osteoarthritis. Patients were recruited when they came to the Hand Surgery Unit. Grip strength, pinch, pain and hand function were measured, and correlation and regression coefficients between them were obtained. For function, the most significant model (R(2)=0.83) included pain and strength. But it is tip to tip pinch force which has a stronger relationship with DASH (Standardized B: -57) questionnaire. Pain also influenced strength measured with the dynamometer but it was tip to tip pinch force that was the most affected. Findings confirm that there is a significant correlation between function referred by the patient and variables that can be measured in the clinic such as grip strength and pinch. The correlation between pain intensity and function was also significant, but tip to tip pinch strength had the greatest impact on the function. Copyright © 2014 Elsevier España, S.L.U. y Sociedad Española de Reumatología y Colegio Mexicano de Reumatología. All rights reserved.

  6. Soil hydraulic properties near saturation, an improved conductivity model

    DEFF Research Database (Denmark)

    Børgesen, Christen Duus; Jacobsen, Ole Hørbye; Hansen, Søren;

    2006-01-01

    The hydraulic properties near saturation can change dramatically due to the presence of macropores that are usually difficult to handle in traditional pore size models. The purpose of this study is to establish a data set on hydraulic conductivity near saturation, test the predictive capability...... of commonly used hydraulic conductivity models and give suggestions for improved models. Water retention and near saturated and saturated hydraulic conductivity were measured for a variety of 81 top and subsoils. The hydraulic conductivity models by van Genuchten [van Genuchten, 1980. A closed-form equation...... for predicting the hydraulic conductivity of unsaturated soils. Soil Sci. Soc. Am. J. 44, 892–898.] (vGM) and Brooks and Corey, modified by Jarvis [Jarvis, 1991. MACRO—A Model of Water Movement and Solute Transport in Macroporous Soils. Swedish University of Agricultural Sciences. Department of Soil Sciences...

  7. 一种同构式主从液压机械手的设计%Design of an Isomorphism Type Master-slave Hydraulic Manipulator

    Institute of Scientific and Technical Information of China (English)

    张丽

    2015-01-01

    提出一种同构式主从液压机械手, 应用直线型光栅作为主手位置的检测装置、 应用步进式电动推杆驱动从手,设计了新型液压传动装置并用此液压装置传递动力, 主手的直线型光栅发出的脉冲经硬件电路处理后, 直接作为步进式电动推杆的驱动与控制脉冲, 步进式电动推杆经液压传动装置把运动传递给机械手的从手, 从手可完全、 实时重复主手的动作.%An isomorphism type master-slave hydraulic manipulator was presented. Applying linear grating as the main hand posi-tion detecting device, applying stepping type electric push rod to drive the slave hand, a new type of hydraulic transmission was designed and the hydraulic device was used to transfer power. The pulses generated by master hand linear grating were processed by the hardware circuit, then they were directly as the control pulses of the stepping electric push rod. Through hydraulic transmission device, the stepping electric push rod transferred the motion to the slave hand, so the slave hand could completely repeat the movements of the main hand real-time.

  8. Hand transplantation--a review.

    Science.gov (United States)

    MacKay, Brendan J; Nacke, Elliot; Posner, Martin

    2014-01-01

    Hand transplantation is a treatment option for complex injuries that leave patients with structural, functional, and aesthetic deficits that cannot be addressed by other means. It is a form of vascularized composite tissue allotransplantation (CTA). CTA is the highest rung the reconstructive ladder due to its complex technical and immunologic challenges. Despite completion of the first successful hand transplant in 1999, our understanding of hand transplantation is still evolving. Ongoing research is needed to improve functional outcomes and decrease the morbidity associated with long-term immunosuppression. This review will discuss the current protocols for upper extremity donation, transplant receipt, surgical technique, postoperative rehabilitation and immunosuppression, nerve regeneration, functional outcomes, ethical issues, and financial considerations.

  9. Hand-it-on”

    DEFF Research Database (Denmark)

    Dieckmann, Gerhard Peter; Graae Zeltner, Louise; Helsø, Anne-Mette

    2016-01-01

    and where they can apply them in their work. It complements existing approaches to teaching NTS by limiting the complexity of the game and by removing medical content, allowing learners to concentrate on NTS. Hand-it-on is relevant for groups and teams working across the range of different healthcare...... variations that can be used in different contexts, focusing the exercise on different learning goals. We also offer the theoretical rationale for using an out-of-context simulation in combination with other forms of teaching. Although we did not evaluate Hand-it-on formally, oral feedback from participants...... and the replication of Hand-it-on by many simulation teams support its value....

  10. Hand-Based Biometric Analysis

    Science.gov (United States)

    Bebis, George (Inventor); Amayeh, Gholamreza (Inventor)

    2015-01-01

    Hand-based biometric analysis systems and techniques are described which provide robust hand-based identification and verification. An image of a hand is obtained, which is then segmented into a palm region and separate finger regions. Acquisition of the image is performed without requiring particular orientation or placement restrictions. Segmentation is performed without the use of reference points on the images. Each segment is analyzed by calculating a set of Zernike moment descriptors for the segment. The feature parameters thus obtained are then fused and compared to stored sets of descriptors in enrollment templates to arrive at an identity decision. By using Zernike moments, and through additional manipulation, the biometric analysis is invariant to rotation, scale, or translation or an in put image. Additionally, the analysis utilizes re-use of commonly-seen terms in Zernike calculations to achieve additional efficiencies over traditional Zernike moment calculation.

  11. [Hand hygiene: revolution and globalization].

    Science.gov (United States)

    Pittet, Didier

    2009-04-01

    Hand hygiene is the primary measure to prevent healthcare-associated infections and the spread of antimicrobial resistance. Low staff compliance remains a major problem. Successful promotion requires a multimodal strategy. The World Health Organization (WHO) proposes an approach including at least five components: system change, in particular the recourse to alcohol-based hand rubbing as the new standard of care, staff education using newly developed tools, monitoring and feedback of staff performance, reminders in the workplace, and promotion of an institutional safety climate. Patient participation in hand hygiene promotion is under testing. Early results of the strategy tested in a large number of healthcare settings in both limited- and high-resource countries are extremely encouraging.

  12. Natural control capabilities of robotic hands by hand amputated subjects.

    Science.gov (United States)

    Atzori, Manfredo; Gijsberts, Arjan; Caputo, Barbara; Muller, Henning

    2014-01-01

    People with transradial hand amputations who own a myoelectric prosthesis currently have some control capabilities via sEMG. However, the control systems are still limited and not natural. The Ninapro project is aiming at helping the scientific community to overcome these limits through the creation of publicly available electromyography data sources to develop and test machine learning algorithms. In this paper we describe the movement classification results gained from three subjects with an homogeneous level of amputation, and we compare them with the results of 40 intact subjects. The number of considered subjects can seem small at first sight, but it is not considering the literature of the field (which has to face the difficulty of recruiting trans-radial hand amputated subjects). The classification is performed with four different classifiers and the obtained balanced classification rates are up to 58.6% on 50 movements, which is an excellent result compared to the current literature. Successively, for each subject we find a subset of up to 9 highly independent movements, (defined as movements that can be distinguished with more than 90% accuracy), which is a deeply innovative step in literature. The natural control of a robotic hand in so many movements could lead to an immediate progress in robotic hand prosthetics and it could deeply change the quality of life of amputated subjects.

  13. Urunana Audiences at Home and Away: Together 'Hand in Hand'?

    NARCIS (Netherlands)

    H.M. Hintjens (Helen); F. Bayisenge

    2011-01-01

    textabstractUrunana (‘Hand in Hand’) is Rwanda’s first radio soap opera. The production emerged during the late 1990s from a three-way transnational production partnership between: The Great Lakes section of the BBC World Service; the Well Woman Media Project of the London-based NGO, Health Unlimite

  14. South Davis Sewer District Pump Station Hydraulic Capacity Evaluation

    OpenAIRE

    Dixon, James W

    2011-01-01

    In 2010, South Davis Sewer District (SDSD) determined that possible hydraulic problems existed in their various pump stations operating within their treatment plants. A hydraulic analysis was conducted for the pump stations to diagnose the problems and provide possible alternative solutions. This analysis was conducted by using hydraulic minor loss equations to determine the amount of flow that the pumps were capable of producing and then comparing those results to the required demands in the...

  15. Predictive Maintenance of Hydraulic Lifts through Lubricating Oil Analysis

    OpenAIRE

    Stamatios S. Kalligeros

    2013-01-01

    This article examines the possibility of measuring lift maintenance through analysis of used hydraulic oil. Hydraulic oils have proved to be a reliable indicator for the maintenance performed on elevators. It has also been proved that the end users or the maintenance personnel do not always conform to the instructions of the elevators’ hydraulic machine manufacturer. Furthermore, by examining the proportion of the metals, an estimation of the corrosion and the wear resistance of the joined mo...

  16. M1078 Hybrid Hydraulic Vehicle Fuel Economy Evaluation

    Science.gov (United States)

    2012-09-01

    PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 28-09-2012 2. REPORT TYPE Interim Report 3. DATES COVERED (From...system shakedown and developmental testing. During developmental testing, a hydraulic motor failure occurred. Although not catastrophic, the motor...main hydraulic hybrid system control module to request the TCM to shift the transmission. Clutch Operation with engine- off (hydraulic-only power) or

  17. Research on hydraulic-powered roof supports test problems

    Institute of Scientific and Technical Information of China (English)

    SUN Hong-bo; JIANG Jin-qiu; MA Qiang

    2011-01-01

    The load-bearing characters of hydraulic-powered roof support with dual telescopic legs were analyzed. With a specific type hydraulic-powered roof support with dual telescopic legs for research object, the inside load test problems in factories was analyzed, and the correct test methods were given, which can enhance the test efficiency and make the factories away from the error design of hydraulic-powered roof supports and legs.

  18. Hydraulics national laboratory; Laboratoire national d`hydraulique

    Energy Technology Data Exchange (ETDEWEB)

    Chabard, J.P.

    1995-12-31

    The hydraulics national laboratory is a department of the service of applications of electric power and environment from the direction of studies and researches of Electricite de France. It has to solve the EDF problems concerning the fluids mechanics and hydraulics. Problems in PWR type reactors, fossil fuel power plants, circulating fluidized bed power plants, hydroelectric power plants relative to fluid mechanics and hydraulics studied and solved in 1995 are explained in this report. (N.C.)

  19. Intrinsic contractures of the hand.

    Science.gov (United States)

    Paksima, Nader; Besh, Basil R

    2012-02-01

    Contractures of the intrinsic muscles of the fingers disrupt the delicate and complex balance of intrinsic and extrinsic muscles, which allows the hand to be so versatile and functional. The loss of muscle function primarily affects the interphalangeal joints but also may affect etacarpophalangeal joints. The resulting clinical picture is often termed, intrinsic contracture or intrinsic-plus hand. Disruption of the balance between intrinsic and extrinsic muscles has many causes and may be secondary to changes within the intrinsic musculature or the tendon unit. This article reviews diagnosis, etiology, and treatment algorithms in the management of intrinsic contractures of the fingers. Copyright © 2012 Elsevier Inc. All rights reserved.

  20. Hand Recognition in Live-Streaming Video

    OpenAIRE

    Mikhail, Belov

    2011-01-01

    The article describes the algorithmic component of the pattern recognition method for extracting hand patterns from a video stream. Methods removing excess information from frames, localizing fragments with a hand and extracting hand contours to classify them are described.