WorldWideScience

Sample records for hybrid integrated optical

  1. Characterisation of hybrid integrated all-optical flip-flop

    DEFF Research Database (Denmark)

    Liu, Y.; McDougall, R.; Seoane, Jorge

    2006-01-01

    We present a fully-packaged, hybrid-integrated all-optical flip-flop with separate optical set and reset operation. The flip-flop can control a wavelength converter to route 40 Gb/s data packets all-optically. The experimental results are given.......We present a fully-packaged, hybrid-integrated all-optical flip-flop with separate optical set and reset operation. The flip-flop can control a wavelength converter to route 40 Gb/s data packets all-optically. The experimental results are given....

  2. Design of integrated hybrid silicon waveguide optical gyroscope.

    Science.gov (United States)

    Srinivasan, Sudharsanan; Moreira, Renan; Blumenthal, Daniel; Bowers, John E

    2014-10-20

    We propose and analyze a novel highly integrated optical gyroscope using low loss silicon nitride waveguides. By integrating the active optical components on chip, we show the possibility of reaching a detection limit on the order of 19°/hr/√Hz in an area smaller than 10 cm(2). This study examines a number of parameters, including the dependence of sensitivity on sensor area.

  3. 40-Gb/s all-optical processing systems using hybrid photonic integration technology

    DEFF Research Database (Denmark)

    Kehayas, E.; Tsiokos, D.I.; Bakopoulos, P.;

    2006-01-01

    This paper presents an experimental performance characterization of all-optical subsystems at 40 Gb/s using interconnected hybrid integrated all-optical semiconductor optical amplifier (SOA) Mach-Zehnder interferometer (MZI) gates and flip-flop prototypes. It was shown that optical gates can...... the potential that all-optical technology can find application in future data-centric networks with efficient and dynamic bandwidth utilization. This paper also reports on the latest photonic integration breakthroughs as a potential migration path for reducing fabrication cost by developing photonic systems...

  4. Cascaded all-optical operations in a hybrid integrated 80-Gb/s logic circuit.

    Science.gov (United States)

    LeGrange, J D; Dinu, M; Sochor, T; Bollond, P; Kasper, A; Cabot, S; Johnson, G S; Kang, I; Grant, A; Kay, J; Jaques, J

    2014-06-01

    We demonstrate logic functionalities in a high-speed all-optical logic circuit based on differential Mach-Zehnder interferometers with semiconductor optical amplifiers as the nonlinear optical elements. The circuit, implemented by hybrid integration of the semiconductor optical amplifiers on a planar lightwave circuit platform fabricated in silica glass, can be flexibly configured to realize a variety of Boolean logic gates. We present both simulations and experimental demonstrations of cascaded all-optical operations for 80-Gb/s on-off keyed data.

  5. All-fiber hybrid photon-plasmon circuits: integrating nanowire plasmonics with fiber optics.

    Science.gov (United States)

    Li, Xiyuan; Li, Wei; Guo, Xin; Lou, Jingyi; Tong, Limin

    2013-07-01

    We demonstrate all-fiber hybrid photon-plasmon circuits by integrating Ag nanowires with optical fibers. Relying on near-field coupling, we realize a photon-to-plasmon conversion efficiency up to 92% in a fiber-based nanowire plasmonic probe. Around optical communication band, we assemble an all-fiber resonator and a Mach-Zehnder interferometer (MZI) with Q-factor of 6 × 10(6) and extinction ratio up to 30 dB, respectively. Using the MZI, we demonstrate fiber-compatible plasmonic sensing with high sensitivity and low optical power.

  6. Hybrid Integrated Photonics for Ultrahigh Throughput Optical Signal Processing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Structured Materials Industries, Inc. and Cornell University propose to develop high speed integrated photonic switches and WDM for LIDAR applications. The team has...

  7. Integrated optical frequency shifter in silicon-organic hybrid (SOH) technology.

    Science.gov (United States)

    Lauermann, M; Weimann, C; Knopf, A; Heni, W; Palmer, R; Koeber, S; Elder, D L; Bogaerts, W; Leuthold, J; Dalton, L R; Rembe, C; Freude, W; Koos, C

    2016-05-30

    We demonstrate for the first time a waveguide-based frequency shifter on the silicon photonic platform using single-sideband modulation. The device is based on silicon-organic hybrid (SOH) electro-optic modulators, which combine conventional silicon-on-insulator waveguides with highly efficient electro-optic cladding materials. Using small-signal modulation, we demonstrate frequency shifts of up to 10 GHz. We further show large-signal modulation with optimized waveforms, enabling a conversion efficiency of -5.8 dB while suppressing spurious side-modes by more than 23 dB. In contrast to conventional acousto-optic frequency shifters, our devices lend themselves to large-scale integration on silicon substrates, while enabling frequency shifts that are several orders of magnitude larger than those demonstrated with all-silicon serrodyne devices.

  8. Photonic Routing Systems Using All-optical, Hybrid Integrated Wavelength Converter Arrays

    Directory of Open Access Journals (Sweden)

    Leontios Stampoulidis

    2010-02-01

    Full Text Available The integration of a new generation of all-optical wavelength converters within European project ISTMUFINS has enabled the development of compact and multi-functional photonic processing systems. Here we present the realization of demanding functionalities required in high-capacity photonic routers using these highly integrated components including: Clock recovery, data/label recovery, wavelength routing and contention resolution; all implemented with multi-signal processing using a single photonic chip – a quadruple array of SOAMZI wavelength converters which occupies a chip area of only 15 x 58 mm2. In addition, we present the capability of the technology to build WDM signal processing systems with the simultaneous operation of four quad devices in a four wavelength burst-mode regenerator. Finally, the potential of the technology to provide photonic systems-onchip is demonstrated with the first hybrid integrated alloptical burst-mode receiver prototype.

  9. Broadband energy-efficient optical modulation by hybrid integration of silicon nanophotonics and organic electro-optic polymer

    CERN Document Server

    Zhang, Xingyu; Subbaraman, Harish; Luo, Jingdong; Jen, Alex K -Y; Chung, Chi-jui; Yan, Hai; Pan, Zeyu; Nelson, Robert L; Chen, Ray T

    2015-01-01

    Silicon-organic hybrid integrated devices have emerging applications ranging from high-speed optical interconnects to photonic electromagnetic-field sensors. Silicon slot photonic crystal waveguides (PCWs) filled with electro-optic (EO) polymers combine the slow-light effect in PCWs with the high polarizability of EO polymers, which promises the realization of high-performance optical modulators. In this paper, a broadband, power-efficient, low-dispersion, and compact optical modulator based on an EO polymer filled silicon slot PCW is presented. A small voltage-length product of V{\\pi}*L=0.282Vmm is achieved, corresponding to an unprecedented record-high effective in-device EO coefficient (r33) of 1230pm/V. Assisted by a backside gate voltage, the modulation response up to 50GHz is observed, with a 3-dB bandwidth of 15GHz, and the estimated energy consumption is 94.4fJ/bit at 10Gbit/s. Furthermore, lattice-shifted PCWs are utilized to enhance the optical bandwidth by a factor of ~10X over other modulators bas...

  10. A scanning probe-based pick-and-place procedure for assembly of integrated quantum optical hybrid devices

    CERN Document Server

    Schell, Andreas W; Schröder, Tim; Wolters, Janik; Aichele, Thomas; Benson, Oliver

    2011-01-01

    Integrated quantum optical hybrid devices consist of fundamental constituents such as single emitters and tailored photonic nanostructures. A reliable fabrication method requires the controlled deposition of active nanoparticles on arbitrary nanostructures with highest precision. Here, we describe an easily adaptable technique that employs picking and placing of nanoparticles with an atomic force microscope combined with a confocal setup. In this way, both the topography and the optical response can be monitored simultaneously before and after the assembly. The technique can be applied to arbitrary particles. Here, we focus on nanodiamonds containing single nitrogen vacancy centers, which are particularly interesting for quantum optical experiments on the single photon and single emitter level.

  11. Integration of variable-rate OWC with OFDM-PON for hybrid optical access based on adaptive envelope modulation

    Science.gov (United States)

    Chen, Chen; Zhong, Wen-De; Wu, Dehao

    2016-12-01

    In this paper, we investigate an integrated optical wireless communication (OWC) and orthogonal frequency division multiplexing based passive optical network (OFDM-PON) system for hybrid wired and wireless optical access, based on an adaptive envelope modulation technique. Both the outdoor and indoor wireless communications are considered in the integrated system. The data for wired access is carried by a conventional OFDM signal, while the data for wireless access is carried by an M-ary pulse amplitude modulation (M-PAM) signal which is modulated onto the envelope of a phase-modulated OFDM signal. By adaptively modulating the wireless M-PAM signal onto the envelope of the wired phase-modulated constant envelope OFDM (CE-OFDM) signal, hybrid wired and wireless optical access can be seamlessly integrated and variable-rate optical wireless transmission can also be achieved. Analytical bit-error-rate (BER) expressions are derived for both the CE-OFDM signal with M-PAM overlay and the overlaid unipolar M-PAM signal, which are verified by Monte Carlo simulations. The BER performances of wired access, indoor OWC wireless access and outdoor OWC wireless access are evaluated. Moreover, variable-rate indoor and outdoor optical wireless access based on the adaptive envelope modulation technique is also discussed.

  12. Hybrid graphene/silicon integrated optical isolators with photonic spin-orbit interaction

    CERN Document Server

    Ma, Jingwen; Yu, Zejie; Sun, Xiankai

    2016-01-01

    Optical isolators are an important building block in photonic computation and communication. In traditional optics, isolators are realized with magneto-optical garnets. However, it remains challenging to incorporate such materials on an integrated platform because of the difficulty in material growth and bulky device footprint. Here, we propose an ultracompact integrated isolator by exploiting graphene's magneto-optical property on a silicon-on-insulator platform. The photonic nonreciprocity is achieved because the cyclotrons in graphene experiencing different optical spin exhibit different response to counterpropagating light. Taking advantage of cavity resonance effects, we have numerically optimized a device design, which shows excellent isolation performance with the extinction ratio over 45 dB and the insertion loss around 12 dB at a wavelength near 1.55 um. Featuring graphene's CMOS compatibility and substantially reduced device footprint, our proposal sheds light to monolithic integration of nonrecipro...

  13. Hybrid Photonic Integration on a Polymer Platform

    Directory of Open Access Journals (Sweden)

    Ziyang Zhang

    2015-09-01

    Full Text Available To fulfill the functionality demands from the fast developing optical networks, a hybrid integration approach allows for combining the advantages of various material platforms. We have established a polymer-based hybrid integration platform (polyboard, which provides flexible optical input/ouptut interfaces (I/Os that allow robust coupling of indium phosphide (InP-based active components, passive insertion of thin-film-based optical elements, and on-chip attachment of optical fibers. This work reviews the recent progress of our polyboard platform. On the fundamental level, multi-core waveguides and polymer/silicon nitride heterogeneous waveguides have been fabricated, broadening device design possibilities and enabling 3D photonic integration. Furthermore, 40-channel optical line terminals and compact, bi-directional optical network units have been developed as highly functional, low-cost devices for the wavelength division multiplexed passive optical network. On a larger scale, thermo-optic elements, thin-film elements and an InP gain chip have been integrated on the polyboard to realize a colorless, dual-polarization optical 90° hybrid as the frontend of a coherent receiver. For high-end applications, a wavelength tunable 100Gbaud transmitter module has been demonstrated, manifesting the joint contribution from the polyboard technology, high speed polymer electro-optic modulator, InP driver electronics and ceramic electronic interconnects.

  14. Hybrid Waveguides and Heterodyne Detectors Integrated Optics for 10 Micron Wavelengths

    Science.gov (United States)

    1975-02-28

    approximate the rectangular waveguide 34 of Figure 2 by two orthogonal slab waveguides. Marcuse indicates that this procedure yields an accurate... Marcuse , Theory of Dielectric Optical Waveguides, Academic Press, 1974. 35. T. Takano ?nd J. Hamasaki, "Propagating Modes of a Metal-Clad

  15. Integrated optical sensor using hybrid plasmonics for lab on chip applications

    Science.gov (United States)

    Zaki, Aya O.; Kirah, Khaled; Swillam, Mohamed A.

    2016-08-01

    We propose a novel, compact plasmonic sensing structure based on a metal-insulator-metal waveguide hybridly-coupled to a rectangular side cavity. The structure has been numerically investigated using the finite-difference time-domain method. Transmission spectra obtained from numerical simulations are used to analyze the sensing characteristics of the structure. The effects of the geometrical parameters on transmission and sensing of the structure are studied. With optimum design, sensitivity can reach as high as 1500 nm per refractive-index unit around the resonance wavelength of 1550 nm with a cavity area of 1 μm2. The proposed structure can potentially be applied in on-chip pressure and gas micro-sensors.

  16. Hybrid materials for optics and photonics.

    Science.gov (United States)

    Lebeau, Benedicte; Innocenzi, Plinio

    2011-02-01

    The interest in organic-inorganic hybrids as materials for optics and photonics started more than 25 years ago and since then has known a continuous and strong growth. The high versatility of sol-gel processing offers a wide range of possibilities to design tailor-made materials in terms of structure, texture, functionality, properties and shape modelling. From the first hybrid material with optical functional properties that has been obtained by incorporation of an organic dye in a silica matrix, the research in the field has quickly evolved towards more sophisticated systems, such as multifunctional and/or multicomponent materials, nanoscale and self-assembled hybrids and devices for integrated optics. In the present critical review, we have focused our attention on three main research areas: passive and active optical hybrid sol-gel materials, and integrated optics. This is far from exhaustive but enough to give an overview of the huge potential of these materials in photonics and optics (254 references).

  17. Hybrid silicon evanescent approach to optical interconnects

    OpenAIRE

    Liang, Di; Fang, Alexander W.; Chen, Hui-Wen; Sysak, Matthew N; Koch, Brian R.; Lively, Erica; Raday, Omri; Kuo, Ying-hao; Jones, Richard; Bowers, John E

    2009-01-01

    We discuss the recently developed hybrid silicon evanescent platform (HSEP), and its application as a promising candidate for optical interconnects in silicon. A number of key discrete components and a wafer-scale integration process are reviewed. The motivation behind this work is to realize silicon-based photonic integrated circuits possessing unique advantages of III–V materials and silicon-on-insulator waveguides simultaneously through a complementary metal-oxide semiconductor fabrication...

  18. Integrated Optics Some Aspects

    Directory of Open Access Journals (Sweden)

    R. Hradaynath

    1990-01-01

    Full Text Available Status of some key individual integrated optics components, their application in the field of telecommunications, integrated optoelectronic circuits, fibre optics sensors, optical interconnects and logic devices are highlighted in this paper. Possibilities of opto-opto processors in the computers field are also outlined.

  19. Fiber-wireless integrated mobile backhaul network based on a hybrid millimeter-wave and free-space-optics architecture with an adaptive diversity combining technique.

    Science.gov (United States)

    Zhang, Junwen; Wang, Jing; Xu, Yuming; Xu, Mu; Lu, Feng; Cheng, Lin; Yu, Jianjun; Chang, Gee-Kung

    2016-05-01

    We propose and experimentally demonstrate a novel fiber-wireless integrated mobile backhaul network based on a hybrid millimeter-wave (MMW) and free-space-optics (FSO) architecture using an adaptive combining technique. Both 60 GHz MMW and FSO links are demonstrated and fully integrated with optical fibers in a scalable and cost-effective backhaul system setup. Joint signal processing with an adaptive diversity combining technique (ADCT) is utilized at the receiver side based on a maximum ratio combining algorithm. Mobile backhaul transportation of 4-Gb/s 16 quadrature amplitude modulation frequency-division multiplexing (QAM-OFDM) data is experimentally demonstrated and tested under various weather conditions synthesized in the lab. Performance improvement in terms of reduced error vector magnitude (EVM) and enhanced link reliability are validated under fog, rain, and turbulence conditions.

  20. Hybrid Optical Inference Machines

    Science.gov (United States)

    1991-09-27

    imaging. A PC controlled data acquistion system with digital to analog-output was setup with serial- 66 - I controlled linear translation and rotation...rules in Eq. (4) of specific conclusions which are logica ,, .ferred form-the knowledge base. from the facts and rules in response to the queries. In...error rates, digital S 0ucries Conclusions optical signals (binary intensity levels) are assumed for all input and output signals in the optical

  1. Integrated Optical Sensors

    NARCIS (Netherlands)

    Lambeck, Paul; Hoekstra, Hugo

    2003-01-01

    The optical (tele-) communication is the main driving force for the worldwide R&D on integrated optical devices and microsystems. lO-sensors have to compete with many other sensor types both within the optical domain (fiber sensors) and outside that domain, where sensors based on measurand induced c

  2. Integrated Optical Sensors

    NARCIS (Netherlands)

    Lambeck, Paul V.; Hoekstra, Hugo

    2003-01-01

    The optical (tele-) communication is the main driving force for the worldwide R&D on integrated optical devices and microsystems. lO-sensors have to compete with many other sensor types both within the optical domain (fiber sensors) and outside that domain, where sensors based on measurand induced c

  3. Advances in integrated optics

    CERN Document Server

    Chester, A; Bertolotti, M

    1994-01-01

    This volwne contains the Proceedings of a two-week summer conference titled "Advances in Integrated Optics" held June 1-9, 1993, in Erice, Sicily. This was the 18th annual course organized by the International School of Quantum Electronics, under the auspices of the "Ettore Majorana" Centre for Scientific Culture. The term Integrated Optics signifies guided-wave optical circuits consisting of two or more devices on a single substrate. Since its inception in the late 1960's, Integrated Optics has evolved from a specialized research topic into a broad field of work, ranging from basic research through commercial applications. Today many devices are available on market while a big effort is devolved to research on integrated nonlinear optical devices. This conference was organized to provide a comprehensive survey of the frontiers of this technology, including fundamental concepts, nonlinear optical materials, devices both in the linear and nonlinear regimes, and selected applications. These Proceedings update a...

  4. Integration of active optical components

    Science.gov (United States)

    Wipiejewski, Torsten; Akulova, Yuliya A.; Fish, Gregory A.; Schow, Clint L.; Koh, Ping; Karim, Adil; Nakagawa, Shigeru; Dahl, Anders; Kozodoy, Peter; Matson, Alex; Short, Bradley W.; Turner, Chuck M.; Penniman, Steven; Larson, Michael C.; Coldren, Christopher W.; Coldren, Larry A.

    2003-06-01

    Integration of active optical components typically serves five goals: enhanced performance, smaller space, lower power dissipation, higher reliability, and lower cost. We are manufacturing widely tunable laser diodes with an integrated high speed electro absorption modulator for metro and all-optical switching applications. The monolithic integration combines the functions of high power laser light generation, wavelength tuning over the entire C-band, and high speed signal modulation in a single chip. The laser section of the chip contains two sampled grating DBRs with a gain and a phase section between them. The emission wavelength is tuned by current injection into the waveguide layers of the DBR and phase sections. The laser light passes through an integrated optical amplifier before reaching the modulator section on the chip. The amplifier boosts the cw output power of the laser and provides a convenient way of power leveling. The modulator is based on the Franz-Keldysh effect for a wide band of operation. The common waveguide through all sections minimizes optical coupling losses. The packaging of the monolithically integrated chip is much simpler compared to a discrete or hybrid solution using a laser chip, an SOA, and an external modulator. Since only one optical fiber coupling is required, the overall packaging cost of the transmitter module is largely reduced. Error free transmission at 2.5Gbit/s over 200km of standard single mode fiber is obtained with less than 1dB of dispersion penalty.

  5. Optical Orientation in Ferromagnet/Semiconductor Hybrids

    OpenAIRE

    Korenev, V. L.

    2008-01-01

    The physics of optical pumping of semiconductor electrons in the ferromagnet/semiconductor hybrids is discussed. Optically oriented semiconductor electrons detect the magnetic state of the ferromagnetic film. In turn, the ferromagnetism of the hybrid can be controlled optically with the help of the semiconductor. Spin-spin interactions near the interface ferromagnet/semiconductor play crucial role in the optical readout and the manipulation of ferromagnetism.

  6. Hybrid silicon evanescent approach to optical interconnects

    Science.gov (United States)

    Liang, Di; Fang, Alexander W.; Chen, Hui-Wen; Sysak, Matthew N.; Koch, Brian R.; Lively, Erica; Raday, Omri; Kuo, Ying-Hao; Jones, Richard; Bowers, John E.

    2009-06-01

    We discuss the recently developed hybrid silicon evanescent platform (HSEP), and its application as a promising candidate for optical interconnects in silicon. A number of key discrete components and a wafer-scale integration process are reviewed. The motivation behind this work is to realize silicon-based photonic integrated circuits possessing unique advantages of III-V materials and silicon-on-insulator waveguides simultaneously through a complementary metal-oxide semiconductor fabrication process. Electrically pumped hybrid silicon distributed feedback and distributed Bragg reflector lasers with integrated hybrid silicon photodetectors are demonstrated coupled to SOI waveguides, serving as the reliable on-chip single-frequency light sources. For the external signal processing, Mach-Zehnder interferometer modulators are demonstrated, showing a resistance-capacitance-limited, 3 dB electrical bandwidth up to 8 GHz and a modulation efficiency of 1.5 V mm. The successful implementation of quantum well intermixing technique opens up the possibility to realize multiple III-V bandgaps in this platform. Sampled grating DBR devices integrated with electroabsorption modulators (EAM) are fabricated, where the bandgaps in gain, mirror, and EAM regions are 1520, 1440 and 1480 nm, respectively. The high-temperature operation characteristics of the HSEP are studied experimentally and theoretically. An overall characteristic temperature ( T 0) of 51°C, an above threshold characteristic temperature ( T 1) of 100°C, and a thermal impedance ( Z T ) of 41.8°C/W, which agrees with the theoretical prediction of 43.5°C/W, are extracted from the Fabry-Perot devices. Scaling this platform to larger dimensions is demonstrated up to 150 mm wafer diameter. A vertical outgassing channel design is developed to accomplish high-quality III-V epitaxial transfer to silicon in a timely and dimension-independent fashion.

  7. Photonic Integration on the Hybrid Silicon Evanescent Device Platform

    Directory of Open Access Journals (Sweden)

    Hyundai Park

    2008-01-01

    Full Text Available This paper reviews the recent progress of hybrid silicon evanescent devices. The hybrid silicon evanescent device structure consists of III-V epitaxial layers transferred to silicon waveguides through a low-temperature wafer bonding process to achieve optical gain, absorption, and modulation efficiently on a silicon photonics platform. The low-temperature wafer bonding process enables fusion of two different material systems without degradation of material quality and is scalable to wafer-level bonding. Lasers, amplifiers, photodetectors, and modulators have been demonstrated with this hybrid structure and integration of these individual components for improved optical functionality is also presented. This approach provides a unique way to build photonic active devices on silicon and should allow application of silicon photonic integrated circuits to optical telecommunication and optical interconnects.

  8. Quantum photonics hybrid integration platform

    CERN Document Server

    Murray, Eoin; Meany, Thomas; Flother, Frederick F; Lee, James P; Griffiths, Jonathan P; Jones, Geb A C; Farrer, Ian; Ritchie, David A; Bennet, Anthony J; Shields, Andrew J

    2015-01-01

    Fundamental to integrated photonic quantum computing is an on-chip method for routing and modulating quantum light emission. We demonstrate a hybrid integration platform consisting of arbitrarily designed waveguide circuits and single photon sources. InAs quantum dots (QD) embedded in GaAs are bonded to an SiON waveguide chip such that the QD emission is coupled to the waveguide mode. The waveguides are SiON core embedded in a SiO2 cladding. A tuneable Mach Zehnder modulates the emission between two output ports and can act as a path-encoded qubit preparation device. The single photon nature of the emission was veri?ed by an on-chip Hanbury Brown and Twiss measurement.

  9. Quantum photonics hybrid integration platform

    Energy Technology Data Exchange (ETDEWEB)

    Murray, E.; Floether, F. F. [Cambridge Research Laboratory, Toshiba Research Europe Limited, 208 Science Park, Milton Road, Cambridge CB4 0GZ (United Kingdom); Cavendish Laboratory, University of Cambridge, J.J. Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Ellis, D. J. P.; Meany, T.; Bennett, A. J., E-mail: anthony.bennet@crl.toshiba.co.uk; Shields, A. J. [Cambridge Research Laboratory, Toshiba Research Europe Limited, 208 Science Park, Milton Road, Cambridge CB4 0GZ (United Kingdom); Lee, J. P. [Cambridge Research Laboratory, Toshiba Research Europe Limited, 208 Science Park, Milton Road, Cambridge CB4 0GZ (United Kingdom); Engineering Department, University of Cambridge, 9 J. J. Thomson Avenue, Cambridge CB3 0FA (United Kingdom); Griffiths, J. P.; Jones, G. A. C.; Farrer, I.; Ritchie, D. A. [Cavendish Laboratory, University of Cambridge, J.J. Thomson Avenue, Cambridge CB3 0HE (United Kingdom)

    2015-10-26

    Fundamental to integrated photonic quantum computing is an on-chip method for routing and modulating quantum light emission. We demonstrate a hybrid integration platform consisting of arbitrarily designed waveguide circuits and single-photon sources. InAs quantum dots (QD) embedded in GaAs are bonded to a SiON waveguide chip such that the QD emission is coupled to the waveguide mode. The waveguides are SiON core embedded in a SiO{sub 2} cladding. A tuneable Mach Zehnder interferometer (MZI) modulates the emission between two output ports and can act as a path-encoded qubit preparation device. The single-photon nature of the emission was verified using the on-chip MZI as a beamsplitter in a Hanbury Brown and Twiss measurement.

  10. Hybrid and monolithic integration of planar lightwave circuits (PLCs)

    Science.gov (United States)

    Chen, Ray T.

    2008-02-01

    In this paper, we review the status of monolithic and hybrid integration of planar lightwave circuits (PLCs). Building blocks needed for system integration based on polymeric materials, III-V semiconductor materials, LiNbO 3 and SOI on Silicon are summarized with pros and cons. Due to the maturity of silicon CMOS technology, silicon becomes the platform of choice for optical application specific integrated circuits (OASICs). However, the indirect bandgap of silicon makes the formation of electrically pumped silicon laser a remote plausibility which requires hybrid integration of laser sources made out of III-V compound semicouductor.

  11. Multi-format all-optical processing based on a large-scale, hybridly integrated photonic circuit.

    Science.gov (United States)

    Bougioukos, M; Kouloumentas, Ch; Spyropoulou, M; Giannoulis, G; Kalavrouziotis, D; Maziotis, A; Bakopoulos, P; Harmon, R; Rogers, D; Harrison, J; Poustie, A; Maxwell, G; Avramopoulos, H

    2011-06-01

    We investigate through numerical studies and experiments the performance of a large scale, silica-on-silicon photonic integrated circuit for multi-format regeneration and wavelength-conversion. The circuit encompasses a monolithically integrated array of four SOAs inside two parallel Mach-Zehnder structures, four delay interferometers and a large number of silica waveguides and couplers. Exploiting phase-incoherent techniques, the circuit is capable of processing OOK signals at variable bit rates, DPSK signals at 22 or 44 Gb/s and DQPSK signals at 44 Gbaud. Simulation studies reveal the wavelength-conversion potential of the circuit with enhanced regenerative capabilities for OOK and DPSK modulation formats and acceptable quality degradation for DQPSK format. Regeneration of 22 Gb/s OOK signals with amplified spontaneous emission (ASE) noise and DPSK data signals degraded with amplitude, phase and ASE noise is experimentally validated demonstrating a power penalty improvement up to 1.5 dB.

  12. Hybrid Piezoelectric/Fiber-Optic Sensor Sheets

    Science.gov (United States)

    Lin, Mark; Qing, Xinlin

    2004-01-01

    Hybrid piezoelectric/fiber-optic (HyPFO) sensor sheets are undergoing development. They are intended for use in nondestructive evaluation and long-term monitoring of the integrity of diverse structures, including aerospace, aeronautical, automotive, and large stationary ones. It is anticipated that the further development and subsequent commercialization of the HyPFO sensor systems will lead to economic benefits in the form of increased safety, reduction of life-cycle costs through real-time structural monitoring, increased structural reliability, reduction of maintenance costs, and increased readiness for service. The concept of a HyPFO sensor sheet is a generalization of the concept of a SMART Layer(TradeMark), which is a patented device that comprises a thin dielectric film containing an embedded network of distributed piezoelectric actuator/sensors. Such a device can be mounted on the surface of a metallic structure or embedded inside a composite-material structure during fabrication of the structure. There is has been substantial interest in incorporating sensors other than piezoelectric ones into SMART Layer(TradeMark) networks: in particular, because of the popularity of the use of fiber-optic sensors for monitoring the "health" of structures in recent years, it was decided to incorporate fiber-optic sensors, giving rise to the concept of HyPFO devices.

  13. Prospects For Optical Instruments Using Integrated Optics And Components

    Science.gov (United States)

    Yeoman, M. L.

    1989-10-01

    Integrated optical instruments and their components are described by comparison with existing technology and the potential advantages of the new systems are outlined. Fundamental problems of material fabrication need to be overcome before a truly integrated circuit becomes feasible but useful advances are being made by combining discrete with integrated components in hybrid systems. A very large investment programme in R & D is underway in Europe, the U.S.A. and Japan. The first products to emerge in instrumental form have not yet had a significant influence on industrial and commercial markets. Future prospects will depend upon improvements in capability, reliability and on cost reductions.

  14. Free-space coherent optical communication with orbital angular, momentum multiplexing/demultiplexing using a hybrid 3D photonic integrated circuit.

    Science.gov (United States)

    Guan, Binbin; Scott, Ryan P; Qin, Chuan; Fontaine, Nicolas K; Su, Tiehui; Ferrari, Carlo; Cappuzzo, Mark; Klemens, Fred; Keller, Bob; Earnshaw, Mark; Yoo, S J B

    2014-01-13

    We demonstrate free-space space-division-multiplexing (SDM) with 15 orbital angular momentum (OAM) states using a three-dimensional (3D) photonic integrated circuit (PIC). The hybrid device consists of a silica planar lightwave circuit (PLC) coupled to a 3D waveguide circuit to multiplex/demultiplex OAM states. The low excess loss hybrid device is used in individual and two simultaneous OAM states multiplexing and demultiplexing link experiments with a 20 Gb/s, 1.67 b/s/Hz quadrature phase shift keyed (QPSK) signal, which shows error-free performance for 379,960 tested bits for all OAM states.

  15. Tuneable planar integrated optical systems.

    Science.gov (United States)

    Amberg, M; Oeder, A; Sinzinger, S; Hands, P J W; Love, G D

    2007-08-20

    Planar integrated free-space optical systems are well suited for a variety of applications, such as optical interconnects and security devices. Here, we demonstrate for the first time dynamic functionality of such microoptical systems by the integration of adaptive liquid-crystal-devices.

  16. Hybrid optical antennas with photonic resistors.

    Science.gov (United States)

    Butakov, N A; Schuller, J A

    2015-11-16

    Hybrid optical antennas, comprising active materials placed in the gaps of plasmonic split-ring-resonators and nano-dimers, have been the subject of numerous recent investigations. Engineered coupling between the two plasmonic resonators is achieved by modulating the active material, enabling control over the near- and far-field electromagnetic properties. Here, using electromagnetics calculations, we study the evolving optical response of a hybrid metal-semiconductor-metal nanorod antenna as the semiconductor free charge carrier density is continuously varied. In particular, we demonstrate qualitatively new behavior arising from epsilon-near-zero properties in intermediately doped semiconductors. In agreement with optical nano-circuit theory, we show that in the epsilon-near-zero regime such a load acts as an ideal optical resistor with an optimized damping response and strongly suppressed electromagnetic scattering. In periodic arrays, or metasurfaces, we then show how to use these effects to construct high-efficiency nanophotonic intensity modulators for dynamically shaping light.

  17. Hybrid optical acoustic seafloor mapping

    Science.gov (United States)

    Inglis, Gabrielle

    The oceanographic research and industrial communities have a persistent demand for detailed three dimensional sea floor maps which convey both shape and texture. Such data products are used for archeology, geology, ship inspection, biology, and habitat classification. There are a variety of sensing modalities and processing techniques available to produce these maps and each have their own potential benefits and related challenges. Multibeam sonar and stereo vision are such two sensors with complementary strengths making them ideally suited for data fusion. Data fusion approaches however, have seen only limited application to underwater mapping and there are no established methods for creating hybrid, 3D reconstructions from two underwater sensing modalities. This thesis develops a processing pipeline to synthesize hybrid maps from multi-modal survey data. It is helpful to think of this processing pipeline as having two distinct phases: Navigation Refinement and Map Construction. This thesis extends existing work in underwater navigation refinement by incorporating methods which increase measurement consistency between both multibeam and camera. The result is a self consistent 3D point cloud comprised of camera and multibeam measurements. In map construction phase, a subset of the multi-modal point cloud retaining the best characteristics of each sensor is selected to be part of the final map. To quantify the desired traits of a map several characteristics of a useful map are distilled into specific criteria. The different ways that hybrid maps can address these criteria provides justification for producing them as an alternative to current methodologies. The processing pipeline implements multi-modal data fusion and outlier rejection with emphasis on different aspects of map fidelity. The resulting point cloud is evaluated in terms of how well it addresses the map criteria. The final hybrid maps retain the strengths of both sensors and show significant improvement

  18. Fiber optic to integrated optical chip coupler

    Science.gov (United States)

    Pikulski, Joseph I. (Inventor); Ramer, O. Glenn (Inventor)

    1987-01-01

    Optical fibers are clamped by a block onto a substrate. Thereupon, metal is plated over the fibers to hold them in place upon the substrate. The clamp block is removed and the opening, resulting from the clamp block's presence, is then plated in. The built-up metallic body is a coupling which holds the fibers in position so that the ends can be polished for coupling to an integrated optical chip upon a coupling fixture.

  19. Hybrid sol-gel optical materials

    Science.gov (United States)

    Zeigler, John M.

    1992-01-01

    Hybrid sol-gel materials comprise silicate sols cross-linked with linear polysilane, polygermane, or poly(silane-germane). The sol-gel materials are useful as optical identifiers in tagging and verification applications and, in a different aspect, as stable, visible light transparent non-linear optical materials. Methyl or phenyl silicones, polyaryl sulfides, polyaryl ethers, and rubbery polysilanes may be used in addition to the linear polysilane. The linear polymers cross-link with the sol to form a matrix having high optical transparency, resistance to thermooxidative aging, adherence to a variety of substrates, brittleness, and a resistance to cracking during thermal cycling.

  20. Hybrid Integrated Platforms for Silicon Photonics

    Directory of Open Access Journals (Sweden)

    John E. Bowers

    2010-03-01

    Full Text Available A review of recent progress in hybrid integrated platforms for silicon photonics is presented. Integration of III-V semiconductors onto silicon-on-insulator substrates based on two different bonding techniques is compared, one comprising only inorganic materials, the other technique using an organic bonding agent. Issues such as bonding process and mechanism, bonding strength, uniformity, wafer surface requirement, and stress distribution are studied in detail. The application in silicon photonics to realize high-performance active and passive photonic devices on low-cost silicon wafers is discussed. Hybrid integration is believed to be a promising technology in a variety of applications of silicon photonics.

  1. Hybrid wide-band, low-phase-noise scheme for Raman lasers in atom interferometry by integrating an acousto-optic modulator and a feedback loop.

    Science.gov (United States)

    Wang, Kai; Yao, Zhanwei; Li, Runbing; Lu, Sibin; Chen, Xi; Wang, Jin; Zhan, Mingsheng

    2016-02-10

    We report a hybrid scheme for phase-coherent Raman lasers with low phase noise in a wide frequency range. In this scheme, a pair of Raman lasers with a frequency difference of 3.04 GHz is generated by the ±1-order diffracted lights of an acousto-optic modulator (1.52 GHz), where a feedback loop is simultaneously applied for suppressing the phase noise. The beat width of the Raman lasers is narrower than 3 Hz. In the low-frequency range, the phase noise of the Raman lasers is suppressed by 35 dB with the feedback. The phase noise is less than -109  dBc/Hz in the high-frequency range. The sensitivity of an atom gyroscope employing the hybrid Raman lasers can be implicitly improved 10 times. Due to the better high-frequency response, the sensitivity is not limited by the durations of Raman pulses. This work is important for improving the performance of atom-interferometer-based measurements.

  2. Integrated Access to Hybrid Information Resources

    OpenAIRE

    Tamar Sadeh

    2003-01-01

    This paper is entitled "Integrated access to hybrid information resources", but integrated access is just a means to reach an end. Our challenge is to create an integrated environment in a heterogeneous world. Users are not aware, and do not want to be aware, of the differences between the various information resources that their institution provides. All they want is to be able to attain the information they are looking for, in the simplest and most straightforward way possible.

  3. Integrated Optics Theory and Technology

    CERN Document Server

    Hunsperger, Robert G

    2009-01-01

    Integrated Optics: Theory and Technology explains the subject of optoelectronic devices and their use in integrated optics and fiber optic systems. The text emphasizes the physics of how devices work and how they can be used in various applications. Mathematical derivations and the development of design equations are provided where necessary to explain phenomena and engineering principles, but a strong effort has been made to avoid obscuring important concepts with mathematical details. Illustrations and references from technical journals have been used to demonstrate the relevance of the theory to currently important topics in industry. This sixth edition of Integrated Optics: Theory and Technology includes updates and revisions in all chapters, as well as a completely new chapter on nanophotonics. Problems are included at the end of each chapter to develop students' knowledge. Scientists, engineers, students and engineering managers can utilize this book to obtain an overall view of the theory and the most ...

  4. Networked Operations of Hybrid Radio Optical Communications Satellites

    Science.gov (United States)

    Hylton, Alan; Raible, Daniel

    2014-01-01

    In order to address the increasing communications needs of modern equipment in space, and to address the increasing number of objects in space, NASA is demonstrating the potential capability of optical communications for both deep space and near-Earth applications. The Integrated Radio Optical Communications (iROC) is a hybrid communications system that capitalizes on the best of both the optical and RF domains while using each technology to compensate for the other's shortcomings. Specifically, the data rates of the optical links can be higher than their RF counterparts, whereas the RF links have greater link availability. The focus of this paper is twofold: to consider the operations of one or more iROC nodes from a networking point of view, and to suggest specific areas of research to further the field. We consider the utility of Disruption Tolerant Networking (DTN) and the Virtual Mission Operation Center (VMOC) model.

  5. Integrated Radio and Optical Communication (iROC)

    Science.gov (United States)

    Raible, Daniel; Romanofsky, Robert; Pease, Gary; Kacpura, Thomas

    2016-01-01

    This is an overview of the Integrated Radio and Optical Communication (iROC) Project for Space Communication and Navigation Industry Days. The Goal is to develop and demonstrate new, high payoff space technologies that will promote mission utilization of optical communications, thereby expanding the capabilities of NASA's exploration, science, and discovery missions. This is an overview that combines the paramount features of select deep space RF and optical communications elements into an integrated system, scalable from deep space to near earth. It will realize Ka-band RF and 1550 nanometer optical capability. The approach is to prototype and demonstrate performance of key components to increase to TRL-5, leading to integrated hybrid communications system demonstration to increase to TRL-5, leading to integrated hybrid communications system demonstration.

  6. Polymer waveguide based hybrid opto-electric integration technology

    Science.gov (United States)

    Mao, Jinbin; Deng, Lingling; Jiang, Xiyan; Ren, Rong; Zhai, Yumeng; Wang, Jin

    2014-10-01

    While monolithic integration especially based on InP appears to be quite an expensive solution for optical devices, hybrid integration solutions using cheaper material platforms are considered powerful competitors because of the high freedom of design, yield optimization and relative cost-efficiency. Among them, the polymer planar-lightwave circuit (PLC) technology is regarded attractive as polymer offers the potential of fairly simple and low-cost fabrication, and of low-cost packaging. In our work, polymer PLC was fabricated by using the standard reactive ion etching (RIE) technique, while other active and passive devices can be integrated on the polymer PLC platform. Exemplary polymer waveguide devices was a 13-channel arrayed waveguide grating (AWG) chip, where the central channel cross-talk was below -30dB and the polarization dependent frequency shift was mitigated by inserting a half wave plate. An optical 900 hybrid was also realized with one 2×4 multi-mode interferometer (MMI). The excess insertion losses are below 4dB for the C-band, while the transmission imbalance is below 1.2dB. When such an optical hybrid was integrated vertically with mesa-type photodiodes, the responsivity of the individual PD was around 0.06 A/W, while the 3 dB bandwidth reaches 24 ~ 27 GHz, which is sufficient for 100Gbit/s receivers. Another example of the hybrid integration was to couple the polymer waveguides to fiber by applying fiber grooves, whose typical loss value was 0.2 dB per-facet over a broad spectral range from 1200-1600 nm.

  7. Integrated Optical Circuit Devices

    Science.gov (United States)

    1975-02-01

    with a carrier frequency exactly at phase match (w ■ OJQ). 68 I I’ I HI III I "I ■ ^^^^^m^r^^ REFLECTION COEFFICIENT...34 Applied Optics, v9, n 11,p 2444-2452, November 1^70 Marcuse , D., "TL Modes of Graded-Index Slab Waveguides," IFFt J of Quantum Electronics v QF

  8. TWDM-PON-AN optical backhaul solution for hybrid optical wireless networks

    Science.gov (United States)

    Naqshbandi, Fayiqa; Jha, Rakesh Kumar

    2016-10-01

    To improve the performance of broadband access networks Full Service Access Network selected Time and wavelength division multiplexed Passive Optical Network (TWDM-PON) as the primary solution for next-generation optical access (Next-Generation Passive Optical Networks 2 (NGPON2)). This paper reviews the recent progress in this access technology. Different possible solutions for the-next generation access are explained. Comparison of the different TWDM architectures experimentally demonstrated so far is made considering the large split, long reach and high capacity requirements of NGPON2. Major technical challenges in implementing the TWDM networks are discussed. Possible options for designing hybrid wireless-wireline architectures are explained taking care of the high bandwidth provided by the optical networks and high mobility of wireless networks. Also an integrated optical wireless architecture is suggested using TWDM-PON as an optical backhaul.

  9. Integration of microfluidics with a four-channel integrated optical Young interferometer immunosensor

    NARCIS (Netherlands)

    Ymeti, A.; Kanger, J.S.; Greve, J.; Besselink, G.A.J.; Lambeck, P.V.; Wijn, R.; Heideman, R.G.

    2005-01-01

    This report describes an optical sensing hybrid system obtained by bonding a microfluidic system to an integrated optical (IO) four-channel Young interferometer (YI) chip. The microfluidic system implemented into a glass plate consists of four microchannels with cross-sectional dimensions of 200 μm

  10. Integrated approach for hybrid rocket technology development

    Science.gov (United States)

    Barato, Francesco; Bellomo, Nicolas; Pavarin, Daniele

    2016-11-01

    Hybrid rocket motors tend generally to be simple from a mechanical point of view but difficult to optimize because of their complex and still not well understood cross-coupled physics. This paper addresses the previous issue presenting the integrated approach established at University of Padua to develop hybrid rocket based systems. The methodology tightly combines together system analysis and design, numerical modeling from elementary to sophisticated CFD, and experimental testing done with incremental philosophy. As an example of the approach, the paper presents the experience done in the successful development of a hybrid rocket booster designed for rocket assisted take off operations. It is thought that following the proposed approach and selecting carefully the most promising applications it is possible to finally exploit the major advantages of hybrid rocket motors as safety, simplicity, low cost and reliability.

  11. Hybrid Optical Switching for Data Center Networks

    Directory of Open Access Journals (Sweden)

    Matteo Fiorani

    2014-01-01

    Full Text Available Current data centers networks rely on electronic switching and point-to-point interconnects. When considering future data center requirements, these solutions will raise issues in terms of flexibility, scalability, performance, and energy consumption. For this reason several optical switched interconnects, which make use of optical switches and wavelength division multiplexing (WDM, have been recently proposed. However, the solutions proposed so far suffer from low flexibility and are not able to provide service differentiation. In this paper we introduce a novel data center network based on hybrid optical switching (HOS. HOS combines optical circuit, burst, and packet switching on the same network. In this way different data center applications can be mapped to the optical transport mechanism that best suits their traffic characteristics. Furthermore, the proposed HOS network achieves high transmission efficiency and reduced energy consumption by using two parallel optical switches. We consider the architectures of both a traditional data center network and the proposed HOS network and present a combined analytical and simulation approach for their performance and energy consumption evaluation. We demonstrate that the proposed HOS data center network achieves high performance and flexibility while considerably reducing the energy consumption of current solutions.

  12. Hybrid Solution for Integrated Trading

    Directory of Open Access Journals (Sweden)

    Vlad DIACONITA

    2010-01-01

    Full Text Available Integrated applications are complex solutions, whose complexity are determined by the economic processes they implement, the amount of data employed (millions of records grouped in hundreds of tables, databases, hundreds of GB and the number of users. Service oriented architecture (SOA, is now the most talked-about integration solution in mainstream journals, addressing both simple applications, for a department but also at enterprise level. SOA can refer to software architecture or to a way of standardizing the technical architecture of an enterprise and it shows its value when operating in several distinct and heterogeneous environments.

  13. Hybrid Parallel Computation of Integration in GRACE

    CERN Document Server

    Yuasa, F; Kawabata, S; Perret-Gallix, D; Itakura, K; Hotta, Y; Okuda, M; Yuasa, Fukuko; Ishikawa, Tadashi; Kawabata, Setsuya; Perret-Gallix, Denis; Itakura, Kazuhiro; Hotta, Yukihiko; Okuda, Motoi

    2000-01-01

    With an integrated software package {\\tt GRACE}, it is possible to generate Feynman diagrams, calculate the total cross section and generate physics events automatically. We outline the hybrid method of parallel computation of the multi-dimensional integration of {\\tt GRACE}. We used {\\tt MPI} (Message Passing Interface) as the parallel library and, to improve the performance we embedded the mechanism of the dynamic load balancing. The reduction rate of the practical execution time was studied.

  14. Optimised Hybrid Integrated Renewable Energy System

    Directory of Open Access Journals (Sweden)

    Dr. Arun Sandilya

    2012-10-01

    Full Text Available A hybrid integrated renewable energy system for an isolated small community, where grid extension is considered uneconomical. This paper proposed cost optimization through dynamic matching between load and proper equipment sizing. The Matlab based computer program developed for determining the most cost effective energy source to supply required load any given time of the day. Integrated system based on green energy utilization and rural electricity development.

  15. An integrated high-performance beam optics-nuclear processes framework with hybrid transfer map-Monte Carlo particle transport and optimization

    Energy Technology Data Exchange (ETDEWEB)

    Bandura, L., E-mail: bandura@msu.ed [Argonne National Laboratory, Argonne, IL 60439 (United States); Erdelyi, B. [Argonne National Laboratory, Argonne, IL 60439 (United States); Northern Illinois University, DeKalb, IL 60115 (United States); Nolen, J. [Argonne National Laboratory, Argonne, IL 60439 (United States)

    2010-12-01

    An integrated beam optics-nuclear processes framework is essential for accurate simulation of fragment separator beam dynamics. The code COSY INFINITY provides powerful differential algebraic methods for modeling and beam dynamics simulations in absence of beam-material interactions. However, these interactions are key for accurately simulating the dynamics of heavy ion fragmentation and fission. We have developed an extended version of the code that includes these interactions, and a set of new tools that allow efficient and accurate particle transport: by transfer map in vacuum and by Monte Carlo methods in materials. The new framework is presented, along with several examples from a preliminary layout of a fragment separator for a facility for rare isotope beams.

  16. Polarizing Filter for Integrated Optics

    Science.gov (United States)

    Ramer, O. G.; Goss, W. C.; Goldstein, R.

    1986-01-01

    Polarizing filter for titanium-doped lithium niobate light waveguide suppresses transverse magnetic (TM) mode of light propagation while allowing transverse electric (TE) mode to continue on its way. Filter - lithium niobate crystal - is expected to find many applications in integrated optical circuits.

  17. Hybrid ion chains inside an optical cavity

    Science.gov (United States)

    Zhou, Zichao; Siverns, James; Quraishi, Qudsia

    2016-05-01

    Trapped ions remain a leading candidate for the implementation of large-scale quantum networks. These networks require nodes that can store and process quantum information as well as communicate with each other though photonic flying qubits. We propose to use hybrid ion chains of barium, for communication, and ytterbium, for quantum information processing. We report on progress in setting up a hybrid ion chain in a versatile four-blade trap using high numerical aperture collection optics. Although the visible photons produced from barium ions are more favorable as they are not suitable for long distance fiber communication. With this in mind, we intend to implement frequency conversion to overcome this issue. Also, with the view toward increasing the flying-qubit production rate, we propose a cavity-based system to enhance interactions between the ions and photons. The cavity axis is to be placed along the axial direction of the trap allowing a chain of multiple ions to interact with the cavity at the same time. With this configuration the atom-photon coupling strength can be improved by sqrt(N), where N is the number of ions. Experiments will focus on exploring the dynamics of hybrid ion chain, dual species quantum information processing, two-colour entanglement and phase gates assisted by the ion-cavity coupling are to be explored.

  18. Hybrid optical antenna with high directivity gain.

    Science.gov (United States)

    Bonakdar, Alireza; Mohseni, Hooman

    2013-08-01

    Coupling of a far-field optical mode to electronic states of a quantum absorber or emitter is a crucial process in many applications, including infrared sensors, single molecule spectroscopy, and quantum metrology. In particular, achieving high quantum efficiency for a system with a deep subwavelength quantum absorber/emitter has remained desirable. In this Letter, a hybrid optical antenna based on coupling of a photonic nanojet to a metallo-dielectric antenna is proposed, which allows such efficient coupling. A quantum efficiency of about 50% is predicted for a semiconductor with volume of ~λ³/170. Despite the weak optical absorption coefficient of 2000 cm(-1) in the long infrared wavelength of ~8 μm, very strong far-field coupling has been achieved, as evidenced by an axial directivity gain of 16 dB, which is only 3 dB below of theoretical limit. Unlike the common phased array antenna, this structure does not require coherent sources to achieve a high directivity. The quantum efficiency and directivity gain are more than an order of magnitude higher than existing metallic, dielectric, or metallo-dielectric optical antenna.

  19. Facile Preparation of Optically Tailored Hybrid Nanocomposite

    Directory of Open Access Journals (Sweden)

    Susana Fernández de Ávila

    2014-01-01

    Full Text Available Lead sulfide nanoparticles (PbS NPs have been synthesized directly in poly[2-methoxy-5-(3′,7′-dimethyloctyloxy-1,4-phenylenevinylene] (MDMO-PPV semiconducting polymer by a simple low temperature method. Hybrid solutions with different concentrations of PbS with respect to the polymer have been prepared and characterized first in solution and then as thin film nanocomposites deposited on quartz substrates by spin coating. Quenching of photoluminescence emission is observed both in solutions and thin films when the ratio of PbS NPs increases with respect to the polymer, suggesting the occurrence of Dexter energy transfer from the polymer to the PbS NPs. Optical absorption is markedly increased for hybrid solutions compared to pure polymer. In thin nanocomposite films an enhancement of absorbance is observed with increasing PbS NPs concentration, which is more pronounced below 400 nm. The reported results could lead to the development of a method for tailoring the optical response of devices based on PbS NP-polymer nanocomposite by controlling the PbS NP concentration inside the polymer matrix.

  20. Enabling inter- and intra-chip optical wireless interconnect by the aid of hybrid plasmonic leaky-wave optical antennas

    Science.gov (United States)

    Ebrahimi, Vahid; Yousefi, Leila; Mohammad-Taheri, Mahmoud

    2017-01-01

    In this paper, we propose a new method to provide optical link in Photonic Integrated Circuits (PICs). The proposed method uses two hybrid plasmonic leaky-wave optical antennas, operating at the standard optical telecommunication wavelength of 1.55 μm, to provide inter-chip interconnect between two layers in a photonic chip and also intra-chip interconnect between two different photonic ICs. Linearly tapered couplers are designed to couple the optical signal from the silicon waveguide to the hybrid plasmonic antennas. The performance of the proposed optical link is verified using numerical full wave simulation. The proposed structure is planar, and can be fabricated using standard CMOS technology which makes it the superior candidate for realization of future multi-layered Photonic Integrated Circuits.

  1. Integrated optics theory and technology

    CERN Document Server

    Hunsperger, Robert G

    1984-01-01

    Our intent in producing this book was to provide a text that would be comprehensive enough for an introductory course in integrated optics, yet concise enough in its mathematical derivations to be easily readable by a practicing engineer who desires an overview of the field. The response to the first edition has indeed been gratifying; unusually strong demand has caused it to be sold out during the initial year of publication, thus providing us with an early opportunity to produce this updated and improved second edition. This development is fortunate, because integrated optics is a very rapidly progressing field, with significant new research being regularly reported. Hence, a new chapter (Chap. 17) has been added to review recent progress and to provide numerous additional references to the relevant technical literature. Also, thirty-five new problems for practice have been included to supplement those at the ends of chapters in the first edition. Chapters I through 16 are essentially unchanged, except for ...

  2. Hybrid Electro-Optically Modulated Microcombs

    CERN Document Server

    Del'Haye, Pascal; Diddams, Scott A

    2012-01-01

    Optical frequency combs based on mode-locked lasers have proven to be invaluable tools for a wide range of applications in precision spectroscopy and metrology. A novel principle of optical frequency comb generation in whispering-gallery mode microresonators ("microcombs") has been developed recently, which represents a promising route towards chip-level integration and out-of-the-lab use of these devices. Presently, two families of microcombs have been demonstrated: combs with electronically detectable mode spacing that can be directly stabilized, and broadband combs with up to octave-spanning spectra but mode spacings beyond electronic detection limits. However, it has not yet been possible to achieve these two key requirements simultaneously, as will be critical for most microcomb applications. Here we present a key step to overcome this problem by interleaving an electro-optic comb with the spectrum from a parametric microcomb. This allows, for the first time, direct control and stabilization of a microco...

  3. Novel Hybrid Model: Integrating Scrum and XP

    Directory of Open Access Journals (Sweden)

    Zaigham Mushtaq

    2012-06-01

    Full Text Available Scrum does not provide any direction about how to engineer a software product. The project team has to adopt suitable agile process model for the engineering of software. XP process model is mainly focused on engineering practices rather than management practices. The design of XP process makes it suitable for simple and small size projects and not appropriate for medium and large projects. A fine integration of management and engineering practices is desperately required to build quality product to make it valuable for customers. In this research a novel framework hybrid model is proposed to achieve this integration. The proposed hybrid model is actually an express version of Scrum model. It possesses features of engineering practices that are necessary to develop quality software as per customer requirements and company objectives. A case study is conducted to validate the proposal of hybrid model. The results of the case study reveal that proposed model is an improved version of XP and Scrum model.

  4. Integration of hybrid silicon lasers and electroabsorption modulators.

    Science.gov (United States)

    Sysak, Matthew N; Anthes, Joel O; Bowers, John E; Raday, Omri; Jones, Richard

    2008-08-18

    We present an integration platform based on quantum well intermixing for multi-section hybrid silicon lasers and electroabsorption modulators. As a demonstration of the technology, we have fabricated discrete sampled grating DBR lasers and sampled grating DBR lasers integrated with InGaAsP/InP electroabsorption modulators. The integrated sampled grating DBR laser-modulators use the as-grown III-V bandgap for optical gain, a 50 nm blue shifted bandgap for the electrabosprtion modulators, and an 80 nm blue shifted bandgap for low loss mirrors. Laser continuous wave operation up to 45 ?C is achieved with output power >1.0 mW and threshold current of 2GHz with 5 dB DC extinction.

  5. Hybrid plasmon photonic crystal resonance grating for integrated spectrometer biosensor.

    Science.gov (United States)

    Guo, Hong; Guo, Junpeng

    2015-01-15

    Using nanofabricated hybrid metal-dielectric nanohole array photonic crystal gratings, a hybrid plasmonic optical resonance spectrometer biosensor is demonstrated. The new spectrometer sensor technique measures plasmonic optical resonance from the first-order diffraction rather than via the traditional method of measuring optical resonance from transmission. The resonance spectra measured with the new spectrometer technique are compared with the spectra measured using a commercial optical spectrometer. It is shown that the new optical resonance spectrometer can be used to measure plasmonic optical resonance that otherwise cannot be measured with a regular optical spectrometer.

  6. An Optical Receiver Post-Processing System for the Integrated Radio and Optical Communications Software Defined Radio Test Bed

    Science.gov (United States)

    Nappier, Jennifer M.; Tokars, Roger P.; Wroblewski, Adam C.

    2016-01-01

    The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administration's (NASA) Glenn Research Center is investigating the feasibility of a hybrid radio frequency (RF) and optical communication system for future deep space missions. As a part of this investigation, a test bed for a radio frequency (RF) and optical software defined radio (SDR) has been built. Receivers and modems for the NASA deep space optical waveform are not commercially available so a custom ground optical receiver system has been built. This paper documents the ground optical receiver, which is used in order to test the RF and optical SDR in a free space optical communications link.

  7. Vertically Integrated Thermo-Optic Waveguide Switch Using Optical Polymers

    Institute of Scientific and Technical Information of China (English)

    Ki-Hong; Kim; Sang-Yung; Shin; Doo-Sun; Choi

    2003-01-01

    We propose and fabricate a vertically integrated thermo-optic waveguide switch. It controls the optical path between two vertically stacked waveguides using the thermo-optic effect of optical polymer. The measured crosstalk is less than -10 dB.

  8. Vertically Integrated Thermo-Optic Waveguide Switch Using Optical Polymers

    Institute of Scientific and Technical Information of China (English)

    Ki-Hong Kim; Sang-Yung Shin; Doo-Sun Choi

    2003-01-01

    We propose and fabricate a vertically integrated thermo-optic waveguide switch. It controls the optical path between two vertically stacked waveguides using the thermo-optic effect of optical polymer. The measured crosstalk is less than-10 dB.

  9. Advanced optical manufacturing digital integrated system

    Science.gov (United States)

    Tao, Yizheng; Li, Xinglan; Li, Wei; Tang, Dingyong

    2012-10-01

    It is necessarily to adapt development of advanced optical manufacturing technology with modern science technology development. To solved these problems which low of ration, ratio of finished product, repetition, consistent in big size and high precision in advanced optical component manufacturing. Applied business driven and method of Rational Unified Process, this paper has researched advanced optical manufacturing process flow, requirement of Advanced Optical Manufacturing integrated System, and put forward architecture and key technology of it. Designed Optical component core and Manufacturing process driven of Advanced Optical Manufacturing Digital Integrated System. the result displayed effective well, realized dynamic planning Manufacturing process, information integration improved ratio of production manufactory.

  10. Optical Fiber/Nanowire Hybrid Structures for Efficient Three-Dimensional Dye-Sensitized Solar Cells

    KAUST Repository

    Weintraub, Benjamin

    2009-11-09

    Wired up: The energy conversion efficiency of three-dimensional dye-sensitized solar cells (DSSCs) in a hybrid structure that integrates optical fibers and nanowire arrays is greater than that of a two-dimensional device. Internal axial illumination enhances the energy conversion efficiency of a rectangular fiber-based hybrid structure (see picture) by a factor of up to six compared to light illumination normal to the fiber axis from outside the device.

  11. Developing integrated patient pathways using hybrid simulation

    Science.gov (United States)

    Zulkepli, Jafri; Eldabi, Tillal

    2016-10-01

    Integrated patient pathways includes several departments, i.e. healthcare which includes emergency care and inpatient ward; intermediate care which patient(s) will stay for a maximum of two weeks and at the same time be assessed by assessment team to find the most suitable care; and social care. The reason behind introducing the intermediate care in western countries was to reduce the rate of patients that stays in the hospital especially for elderly patients. This type of care setting has been considered to be set up in some other countries including Malaysia. Therefore, to assess the advantages of introducing this type of integrated healthcare setting, we suggest develop the model using simulation technique. We argue that single simulation technique is not viable enough to represent this type of patient pathways. Therefore, we suggest develop this model using hybrid techniques, i.e. System Dynamics (SD) and Discrete Event Simulation (DES). Based on hybrid model result, we argued that the result is viable to be as references for decision making process.

  12. Optical-digital hybrid image search system in cloud environment

    Science.gov (United States)

    Ikeda, Kanami; Kodate, Kashiko; Watanabe, Eriko

    2016-09-01

    To improve the versatility and usability of optical correlators, we developed an optical-digital hybrid image search system consisting of digital servers and an optical correlator that can be used to perform image searches in the cloud environment via a web browser. This hybrid system employs a simple method to obtain correlation signals and has a distributed network design. The correlation signals are acquired by using an encoder timing signal generated by a rotating disk, and the distributed network design facilitates the replacement and combination of the digital correlation server and the optical correlator.

  13. Hybrid enabled thin film metrology using XPS and optical

    Science.gov (United States)

    Vaid, Alok; Iddawela, Givantha; Mahendrakar, Sridhar; Lenahan, Michael; Hossain, Mainul; Timoney, Padraig; Bello, Abner F.; Bozdog, Cornel; Pois, Heath; Lee, Wei Ti; Klare, Mark; Kwan, Michael; Kang, Byung Cheol; Isbester, Paul; Sendelbach, Matthew; Yellai, Naren; Dasari, Prasad; Larson, Tom

    2016-03-01

    Complexity of process steps integration and material systems for next-generation technology nodes is reaching unprecedented levels, the appetite for higher sampling rates is on the rise, while the process window continues to shrink. Current thickness metrology specifications reach as low as 0.1A for total error budget - breathing new life into an old paradigm with lower visibility for past few metrology nodes: accuracy. Furthermore, for advance nodes there is growing demand to measure film thickness and composition on devices/product instead of surrogate planar simpler pads. Here we extend our earlier work in Hybrid Metrology to the combination of X-Ray based reference technologies (high performance) with optical high volume manufacturing (HVM) workhorse metrology (high throughput). Our stated goal is: put more "eyes" on the wafer (higher sampling) and enable move to films on pattern structure (control what matters). Examples of 1X front-end applications are used to setup and validate the benefits.

  14. A fiber optic hybrid multifunctional AC voltage sensor

    Energy Technology Data Exchange (ETDEWEB)

    Sokolovsky, A.; Zadvornov, S. [IRE, Moscow (Russian Federation); Ryabko, M. [UFD, Moscow (Russian Federation)

    2008-07-01

    Hybrid sensors have the advantages of both electronic and optical technologies. Their sensing element is based on conventional transducers and the optical fiber is used as a transmission media for the optical signal encoded with information between the local module and the remote module. The power supply for the remote module is usually provided by a built-in photoelectric converter illuminated by the optical radiation going through the same or another optical fiber. Electro-optic hybrid sensors have been widely used because of the electrical isolation provided by optical fiber. In the conventional fiber optic voltage sensor, piezoelectric or electro-optic transducers are implemented. Processing and conditioning measurement information is a complex task in these sensors. Moreover, the considerable drawback of most of these systems is that only one parameter, usually voltage value, is measured. This paper presented a novel fiber optic hybrid sensor for alternating current voltage measurements. This instrument provides the simultaneous measurement of four parameters, notably voltage value, frequency, phase angle and the external temperature. The paper described the measurement technology of the instrument including the remote module and optical powering as well as the unique modulation algorithm. The results and conclusions were also presented. 7 refs., 4 figs.

  15. Optically induced interaction of magnetic moments in hybrid metamaterials.

    Science.gov (United States)

    Miroshnichenko, Andrey E; Luk'yanchuk, Boris; Maier, Stefan A; Kivshar, Yuri S

    2012-01-24

    We propose a novel type of hybrid metal-dielectric structures composed of silicon nanoparticles and split-ring resonators for advanced control of optically induced magnetic response. We reveal that a hybrid "metamolecule" may exhibit a strong distance-dependent magnetic interaction that may flip the magnetization orientation and support "antiferromagnetic" ordering in a hybrid metamaterial created by a periodic lattice of such metamolecules. The propagation of magnetization waves in the hybrid structures opens new ways for manipulating artificial "antiferromagnetic" ordering at high frequencies. © 2011 American Chemical Society

  16. Optical Waveguides from Organic/Inorganic Hybrid Materials

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Organic/inorganic material has attracted great attentions because its importance as photonic materials. We report on our recent results on organic/inorganic hybrid sol-gel materials and optical waveguides like splitter, thermo-optic switch and micro-cavity laser.

  17. Optical Waveguides from Organic/Inorganic Hybrid Materials

    Institute of Scientific and Technical Information of China (English)

    Liying Liu; Lei Xu; Wencheng Wang

    2003-01-01

    Organic/inorganic material has attracted great attentions because its importance as photonic materials. We report on our recent results on organic/inorganic hybrid sol-gel materials and optical waveguides like splitter,thermo-optic switch and micro-cavity laser.

  18. Isolation of Integrated Optical Acousto-Optic Switch

    Institute of Scientific and Technical Information of China (English)

    XIAO Li-Feng; LIU Ying; WANG Wei-Peng; GENG Fan

    2006-01-01

    @@ Isolation of a new structured acousto-optic switch based on an integrated optical polarization-independent quasicollinear acousto-optic tunable filter is studied in detail. The factors that influence the isolation of the optical switch are analysed, the expressions of the isolation are educed, and the isolation of the device is measured in experiment. It is found that the isolation mainly depends on the TE/TM mode intensity ratio, the mode-splitter extinction rate, and the conversion efficiency.

  19. Integrated optical devices for photonics instrumentation systems

    Energy Technology Data Exchange (ETDEWEB)

    McWright, G.M.; Lafaw, D.A.; Lowry, M.; Tindall, W.

    1990-01-01

    We discuss the design, fabrication, and evaluation of high speed integrated optical devices for application to photonics instrumentation systems. Specifically, we have demonstrated integrated optical devices with bandwidths in excess of 25 GHz and implemented these devices in single-shot, streak camera based recording schemes. 5 refs., 6 figs.

  20. High capacity fiber optic sensor networks using hybrid multiplexing techniques and their applications

    Science.gov (United States)

    Sun, Qizhen; Li, Xiaolei; Zhang, Manliang; Liu, Qi; Liu, Hai; Liu, Deming

    2013-12-01

    Fiber optic sensor network is the development trend of fiber senor technologies and industries. In this paper, I will discuss recent research progress on high capacity fiber sensor networks with hybrid multiplexing techniques and their applications in the fields of security monitoring, environment monitoring, Smart eHome, etc. Firstly, I will present the architecture of hybrid multiplexing sensor passive optical network (HSPON), and the key technologies for integrated access and intelligent management of massive fiber sensor units. Two typical hybrid WDM/TDM fiber sensor networks for perimeter intrusion monitor and cultural relics security are introduced. Secondly, we propose the concept of "Microstructure-Optical X Domin Refecltor (M-OXDR)" for fiber sensor network expansion. By fabricating smart micro-structures with the ability of multidimensional encoded and low insertion loss along the fiber, the fiber sensor network of simple structure and huge capacity more than one thousand could be achieved. Assisted by the WDM/TDM and WDM/FDM decoding methods respectively, we built the verification systems for long-haul and real-time temperature sensing. Finally, I will show the high capacity and flexible fiber sensor network with IPv6 protocol based hybrid fiber/wireless access. By developing the fiber optic sensor with embedded IPv6 protocol conversion module and IPv6 router, huge amounts of fiber optic sensor nodes can be uniquely addressed. Meanwhile, various sensing information could be integrated and accessed to the Next Generation Internet.

  1. Software architecture for hybrid electrical/optical data center network

    DEFF Research Database (Denmark)

    Mehmeri, Victor; Vegas Olmos, Juan José; Tafur Monroy, Idelfonso

    2016-01-01

    This paper presents hardware and software architecture based on Software-Defined Networking (SDN) paradigm and OpenFlow/NETCONF protocols for enabling topology management of hybrid electrical/optical switching data center networks. In particular, a development on top of SDN open-source controller...... OpenDaylight is presented to control an optical switching matrix based on Micro-Electro-Mechanical System (MEMS) technology.......This paper presents hardware and software architecture based on Software-Defined Networking (SDN) paradigm and OpenFlow/NETCONF protocols for enabling topology management of hybrid electrical/optical switching data center networks. In particular, a development on top of SDN open-source controller...

  2. Design and Construction Transceiver Module Using Polymer PLC Hybrid Integration Technology

    OpenAIRE

    Jerabek, Vitezslav; Huttel, Ivan; Prajzler, Vaclav; Busek, Karel

    2010-01-01

    In this paper were presented first steps, which guide to the design and construction of a VHGT attached WDM triplex transceiver module TRx using polymer PLC hybrid integration technology. We report on the results measuring of the optical attenuation of the

  3. Integrated-optics-based optical coherence tomography

    NARCIS (Netherlands)

    Nguyen, D.V.

    2013-01-01

    Optical coherence tomography (OCT) is a high resolution, imaging technique that has developed over the last 20 years from a complicated laboratory setup into a ready-to-use commercially available device. Instead of using electronic time gating as being used by ultrasound (US) imaging, in OCT, the op

  4. Integrated optics approach for advanced semiconductor lasers

    Science.gov (United States)

    Suematsu, Yasuharu; Arai, Shigehisa

    1987-11-01

    Recent advances in the field of semiconductor integrated optics are reviewed from the point of view of monolithic integration of semiconductor lasers and other optical components and/or devices. Emphasis is placed on dynamic-single-mode (DSM) lasers, such as DFB and DBR lasers, intended for highly stable single-wavelength light sources for such monolithic integration. The realization of high-performance DSM lasers and the fabrication techniques of monolithically integrated optical devices and circuits are briefly reviewed. A variety of potential applications is discussed.

  5. Graphene/Si CMOS Hybrid Hall Integrated Circuits

    OpenAIRE

    Huang, Le; Xu, Huilong; Zhang, Zhiyong; Chen, Chengying; Jiang, Jianhua; Ma, Xiaomeng; Chen, Bingyan; Li, Zishen; Zhong, Hua; Peng, Lian-Mao

    2014-01-01

    Graphene/silicon CMOS hybrid integrated circuits (ICs) should provide powerful functions which combines the ultra-high carrier mobility of graphene and the sophisticated functions of silicon CMOS ICs. But it is difficult to integrate these two kinds of heterogeneous devices on a single chip. In this work a low temperature process is developed for integrating graphene devices onto silicon CMOS ICs for the first time, and a high performance graphene/CMOS hybrid Hall IC is demonstrated. Signal a...

  6. A COTS RF/Optical Software Defined Radio for the Integrated Radio and Optical Communications Test Bed

    Science.gov (United States)

    Nappier, Jennifer M.; Zeleznikar, Daniel J.; Wroblewski, Adam C.; Tokars, Roger P.; Schoenholz, Bryan L.; Lantz, Nicholas C.

    2017-01-01

    The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administration (NASA) is investigating the merits of a hybrid radio frequency (RF) and optical communication system for deep space missions. In an effort to demonstrate the feasibility and advantages of a hybrid RF/Optical software defined radio (SDR), a laboratory prototype was assembled from primarily commercial-off-the-shelf (COTS) hardware components. This COTS platform has been used to demonstrate simultaneous transmission of the radio and optical communications waveforms through to the physical layer (telescope and antenna). This paper details the hardware and software used in the platform and various measures of its performance. A laboratory optical receiver platform has also been assembled in order to demonstrate hybrid free space links in combination with the transmitter.

  7. Novel Organo-Soluble Optically Tunable Chiral Hybrid Gold Nanorods

    Science.gov (United States)

    2014-12-04

    alignment in liquid crystal media was achieved. Furthermore, 3D layer-by-layer graphene –gold nanoparticle hybrid architecture with tunable interlayer...nanoparticles which could further guide to fabricate novel nanophotonic and optical metamaterials . Figure TEM images of P8GNR in LCP. (A) Before UV...Building 3D layer-by-layer gold- graphene nanoparticle hybrid architecture with tunable interlayer distance. The ability to construct self-assembled

  8. Hybrid Ground Station Technology for RF and Optical Communication Links

    Science.gov (United States)

    Davarian, Faramaz; Hoppe, D.; Charles, J.; Vilnrotter, V.; Sehic, A.; Hanson, T.; Gam, E.

    2012-01-01

    To support future enhancements of NASA's deep space and planetary communications and tracking services, the Jet Propulsion Laboratory is developing a hybrid ground station that will be capable of simultaneously supporting RF and optical communications. The main reason for adding optical links to the existing RF links is to significantly increase the capacity of deep space communications in support of future solar system exploration. It is envisioned that a mission employing an optical link will also use an RF link for telemetry and emergency purposes, hence the need for a hybrid ground station. A hybrid station may also reduce operations cost by requiring fewer staff than would be required to operate two stations. A number of approaches and techniques have been examined. The most promising ones have been prototyped for field examination and validation.

  9. Optically thin hybrid cavity for terahertz photo-conductive detectors

    Science.gov (United States)

    Thompson, R. J.; Siday, T.; Glass, S.; Luk, T. S.; Reno, J. L.; Brener, I.; Mitrofanov, O.

    2017-01-01

    The efficiency of photoconductive (PC) devices, including terahertz detectors, is constrained by the bulk optical constants of PC materials. Here, we show that optical absorption in a PC layer can be modified substantially within a hybrid cavity containing nanoantennas and a Distributed Bragg Reflector. We find that a hybrid cavity, consisting of a GaAs PC layer of just 50 nm, can be used to absorb >75% of incident photons by trapping the light within the cavity. We provide an intuitive model, which describes the dependence of the optimum operation wavelength on the cavity thickness. We also find that the nanoantenna size is a critical parameter, small variations of which lead to both wavelength shifting and reduced absorption in the cavity, suggesting that impedance matching is key for achieving efficient absorption in the optically thin hybrid cavities.

  10. A Multimodality Hybrid Gamma-Optical Camera for Intraoperative Imaging

    Directory of Open Access Journals (Sweden)

    John E. Lees

    2017-03-01

    Full Text Available The development of low profile gamma-ray detectors has encouraged the production of small field of view (SFOV hand-held imaging devices for use at the patient bedside and in operating theatres. Early development of these SFOV cameras was focussed on a single modality—gamma ray imaging. Recently, a hybrid system—gamma plus optical imaging—has been developed. This combination of optical and gamma cameras enables high spatial resolution multi-modal imaging, giving a superimposed scintigraphic and optical image. Hybrid imaging offers new possibilities for assisting clinicians and surgeons in localising the site of uptake in procedures such as sentinel node detection. The hybrid camera concept can be extended to a multimodal detector design which can offer stereoscopic images, depth estimation of gamma-emitting sources, and simultaneous gamma and fluorescence imaging. Recent improvements to the hybrid camera have been used to produce dual-modality images in both laboratory simulations and in the clinic. Hybrid imaging of a patient who underwent thyroid scintigraphy is reported. In addition, we present data which shows that the hybrid camera concept can be extended to estimate the position and depth of radionuclide distribution within an object and also report the first combined gamma and Near-Infrared (NIR fluorescence images.

  11. Ultrahigh-speed hybrid laser for silicon photonic integrated chips

    DEFF Research Database (Denmark)

    Chung, Il-Sug; Park, Gyeong Cheol; Ran, Qijiang;

    2013-01-01

    and will be 80% in near future. This challenge strongly has motivated replacing electrical interconnects with optical ones even in chip level communications [1]. This chip-level optical interconnects need quite different performance of optoelectronic devices than required for conventional optical communications....... For a light source, the energy consumption per sending a bit is required to be laser diode...... and light-emitting diode (LED) structures have been proposed so far. Our hybrid laser is one of these efforts [2]. The hybrid laser consists of a dielectric reflector, a III-V semiconductor active material, and a high-index-contrast grating (HCG) reflector formed in the silicon layer of a silicon...

  12. Synthesis, characterizations and electro-optical properties of nonlinear optical polyimide/silica hybrid

    Directory of Open Access Journals (Sweden)

    2007-03-01

    Full Text Available Transparent Nonlinear Optical (NLO inorganic/organic (polyimide/silica hybrid composites with covalent links between the inorganic and the organic networks were prepared by the sol-gel method. The silica content in the hybrid films was varied from 0 to 22.5/wt%. The prepared PI hybrids were characterized by IR, UV-Vis, Thermogravimetric analysis (TGA, X-ray diffraction (XRD, Scanning Electron Microscopy (SEM and Transmission Electron Microscopy (TEM. They exhibited fair good optical transparency. The SiO2 phase was well dispersed in the polymer matrix. DSC and TGA results showed that these hybrid materials had excellent thermal stability. The polymer solutions could be spin coated on the indium-tin-oxide (ITO glass to form optical quality thin films. The electro-optic coefficients (γ33 at the wavelength of 832 nm for polymer thin films poled were in the range of 19-27 pm/V.

  13. Advanced materials for integrated optical waveguides

    CERN Document Server

    Tong Ph D, Xingcun Colin

    2014-01-01

    This book provides a comprehensive introduction to integrated optical waveguides for information technology and data communications. Integrated coverage ranges from advanced materials, fabrication, and characterization techniques to guidelines for design and simulation. A concluding chapter offers perspectives on likely future trends and challenges. The dramatic scaling down of feature sizes has driven exponential improvements in semiconductor productivity and performance in the past several decades. However, with the potential of gigascale integration, size reduction is approaching a physical limitation due to the negative impact on resistance and inductance of metal interconnects with current copper-trace based technology. Integrated optics provides a potentially lower-cost, higher performance alternative to electronics in optical communication systems. Optical interconnects, in which light can be generated, guided, modulated, amplified, and detected, can provide greater bandwidth, lower power consumption, ...

  14. Integrated Optical Interconnect Architectures for Embedded Systems

    CERN Document Server

    Nicolescu, Gabriela

    2013-01-01

    This book provides a broad overview of current research in optical interconnect technologies and architectures. Introductory chapters on high-performance computing and the associated issues in conventional interconnect architectures, and on the fundamental building blocks for integrated optical interconnect, provide the foundations for the bulk of the book which brings together leading experts in the field of optical interconnect architectures for data communication. Particular emphasis is given to the ways in which the photonic components are assembled into architectures to address the needs of data-intensive on-chip communication, and to the performance evaluation of such architectures for specific applications.   Provides state-of-the-art research on the use of optical interconnects in Embedded Systems; Begins with coverage of the basics for high-performance computing and optical interconnect; Includes a variety of on-chip optical communication topologies; Features coverage of system integration and opti...

  15. Direct UV-written integrated optical components

    DEFF Research Database (Denmark)

    Svalgaard, Mikael

    2004-01-01

    Direct UV writing is an emerging method for flexible, low cost fabrication of integrated optical waveguides and components. The performance of UV written components can be similar to that achieved with more elaborate fabrication techniques.......Direct UV writing is an emerging method for flexible, low cost fabrication of integrated optical waveguides and components. The performance of UV written components can be similar to that achieved with more elaborate fabrication techniques....

  16. Integrated optical fiber lattice accumulators

    OpenAIRE

    Atherton, Adam F

    1997-01-01

    Approved for public release; distribution is unlimited. Sigma-delta modulators track a signal by accumulating the error between an input signal and a feedback signal. The accumulated energy is amplitude analyzed by a comparator. The comparator output signal is fed back and subtracted from the input signal. This thesis is primarily concerned with designing accumulators for inclusion in an optical sigma-delta modulator. Fiber lattice structures with optical amplifiers are used to perform the...

  17. Hybrid micro-/nanogels for optical sensing and intracellular imaging

    Directory of Open Access Journals (Sweden)

    Shuiqin Zhou

    2010-12-01

    Full Text Available Hybrid micro-/nanogels are playing an increasing important part in a diverse range of applications, due to their tunable dimensions, large surface area, stable interior network structure, and a very short response time. We review recent advances and challenges in the developments of hybrid micro-/nanogels toward applications for optical sensing of pH, temperature, glucose, ions, and other species as well as for intracellular imaging. Due to their unique advantages, hybrid micro-/nanogels as optical probes are attracting substantial interests for continuous monitoring of chemical parameters in complex samples such as blood and bioreactor fluids, in chemical research and industry, and in food quality control. In particular, their intracellular probing ability enables the monitoring of the biochemistry and biophysics of live cells over time and space, thus contributing to the explanation of intricate biological processes and the development of novel diagnoses. Unlike most other probes, hybrid micro-/nanogels could also combine other multiple functions into a single probe. The rational design of hybrid micro-/nanogels will not only improve the probing applications as desirable, but also implement their applications in new arenas. With ongoing rapid advances in bionanotechnology, the well-designed hybrid micro-/nanogel probes will be able to provide simultaneous sensing, imaging diagnosis, and therapy toward clinical applications.

  18. Metal-slotted hybrid optical waveguides for PCB-compatible optical interconnection.

    Science.gov (United States)

    Kim, Jin Tae; Ju, Jung Jin; Park, Suntak

    2012-04-23

    For development of electro-optical printed circuit board (PCB) systems, PCB-compatible metal-slotted hybrid optical waveguide was proposed and its optical characteristics are investigated at a wavelength of 1.31 μm. To confine light in a metallic multilayered structure, a metal film with a wide trench is inserted at the center of a dielectric medium that is sandwiched between metal films of infinite width. A circularly symmetric spot of the guided mode was measured at the center of the metal-slotted optical waveguide, which is a good agreement with the theoretical prediction by using the finite-element method. The measured propagation loss is about 1.5 dB/cm. Successful transmission of 2.5 Gbps optical signal without any distortion of the eye diagram confirms that the proposed hybrid optical waveguide holds a potential transmission line for the PCB-compatible optical interconnection.

  19. Integrated optical biosensor system (IOBS)

    Science.gov (United States)

    Grace, Karen M.; Sweet, Martin R.; Goeller, Roy M.; Morrison, Leland Jean; Grace, Wynne Kevin; Kolar, Jerome D.

    2007-10-30

    An optical biosensor has a first enclosure with a pathogen recognition surface, including a planar optical waveguide and grating located in the first enclosure. An aperture is in the first enclosure for insertion of sample to be investigated to a position in close proximity to the pathogen recognition surface. A laser in the first enclosure includes means for aligning and means for modulating the laser, the laser having its light output directed toward said grating. Detection means are located in the first enclosure and in optical communication with the pathogen recognition surface for detecting pathogens after interrogation by the laser light and outputting the detection. Electronic means is located in the first enclosure and receives the detection for processing the detection and outputting information on the detection, and an electrical power supply is located in the first enclosure for supplying power to the laser, the detection means and the electronic means.

  20. All-Optical Reversible Hybrid New Gate using TOAD

    Directory of Open Access Journals (Sweden)

    Goutam Kumar Maity

    2014-03-01

    Full Text Available Reversible logic is emerged as a promising computing paradigm with applications in low-power CMOS, quantum computing, optical computing and nanotechnology. Optical logic gates become potential component to work at macroscopic (light pulses carry information, or quantum (single photon carries information levels with high efficiency. In this paper, we propose a novel scheme of Hybrid new gate realization in all-optical domain. Simulation results verify the functionality of the gate as well as reversibility. Approximate insertion power loss in dB is also reported for the Gaussian incident and control pulse.

  1. Electrochemical and Optical Evaluation of Noble Metal-and Carbon-ITO Hybrid Optically Transparent Electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Zudans, Imants; Paddock, Jean R.; Kuramitz, Hideki; Maghasi, Anne T.; Wansapura, Chamika M.; Conklin, Sean D.; Kaval, Necati; Shtoyko, Tanya; Monk, David J.; Bryan, Samuel A.; Hubler, Timothy L.; Richardson, John N.; Seliskar, Carl J.; Heineman, William R.

    2004-04-15

    Optically transparent hybrid electrodes were constructed by sputtering or thermally evaporating layers of varying thickness of Au, Pd, Pt, or C onto an existing conductive indium-tin oxide (ITO) layer on glass. These electrodes were characterized using UV-Vis spectroscopy and cyclic voltammetry; redox probes examined were potassium ferricyanide, tris-(2, 2'-bipyridyl)ruthenium(II) chloride, hydroquinone, and para-aminophenol (PAP). Each type of hybrid was evaluated and compared with other hybrids, as well as with bare ITO electrodes and commercially available Au, Pt, and glassy carbon disk electrodes. Our results indicated that these hybrid electrodes are reasonably robust, easy to prepare, and extend the capabilities of bare ITO surfaces with respect to the electrochemical response (especially for organic redox probes), while giving up little in the way of optical transparency. Because of these characteristics, hybrid electrodes should be especially suited to many spectroelectrochemical applications.

  2. Harnessing optical forces in integrated photonic circuits.

    Science.gov (United States)

    Li, Mo; Pernice, W H P; Xiong, C; Baehr-Jones, T; Hochberg, M; Tang, H X

    2008-11-27

    The force exerted by photons is of fundamental importance in light-matter interactions. For example, in free space, optical tweezers have been widely used to manipulate atoms and microscale dielectric particles. This optical force is expected to be greatly enhanced in integrated photonic circuits in which light is highly concentrated at the nanoscale. Harnessing the optical force on a semiconductor chip will allow solid state devices, such as electromechanical systems, to operate under new physical principles. Indeed, recent experiments have elucidated the radiation forces of light in high-finesse optical microcavities, but the large footprint of these devices ultimately prevents scaling down to nanoscale dimensions. Recent theoretical work has predicted that a transverse optical force can be generated and used directly for electromechanical actuation without the need for a high-finesse cavity. However, on-chip exploitation of this force has been a significant challenge, primarily owing to the lack of efficient nanoscale mechanical transducers in the photonics domain. Here we report the direct detection and exploitation of transverse optical forces in an integrated silicon photonic circuit through an embedded nanomechanical resonator. The nanomechanical device, a free-standing waveguide, is driven by the optical force and read out through evanescent coupling of the guided light to the dielectric substrate. This new optical force enables all-optical operation of nanomechanical systems on a CMOS (complementary metal-oxide-semiconductor)-compatible platform, with substantial bandwidth and design flexibility compared to conventional electrical-based schemes.

  3. Pigtailing of integrated optical components

    DEFF Research Database (Denmark)

    Zenth, Karin

    2001-01-01

    , but also a silicon motherboard for laser diode pigtailing and a Variable Optical Attenuator have been realized. The pigtailing method consists of three major parts: a waveguide chip with alignment trenches, a fiber array with alignment trenches, and a top plate with alignment rails. The top plate aligns...

  4. CAD Integration : new optical design possibilities

    Science.gov (United States)

    Haumonte, Jean-Baptiste; Venturino, Jean-Claude

    2005-09-01

    The development of optical design and analysis tools in a CAD software can help to optimise the design, size and performance of tomorrow's consumer products. While optics was still held back by software limitations, CAD programs were moving forward in leaps and bounds, improving manufacturing technologies and making it possible to design and produce highly innovative and sophisticated products. The problem was that in the past, 'traditional' optical design programs were only able to simulate spherical and aspherical lenses, meaning that the optical designers were limited to designing systems which were a series of imperfect lenses, each one correcting the last. That is why OPTIS has created the first optical design program to be fully integrated into a CAD program. The technology is available from OPTIS in an integrated SOLIDWORKS or CATIA V5 version. Users of this software can reduce the number of lenses needed in a system. Designers will now have access to complex surfaces such as NURBS meaning they will now be able to define free shape progressive lenses and even improve on optical performances using fewer lenses. This revolutionary technology will allow mechanical designers to work on optical systems and to share information with optical designers for the first time. Previously not possible in a CAD program you may now determine all the optical performances of any optical system, providing first order and third order performances, sequential and non-sequential ray-tracing, wavefront surfaces, point spread function, MTF, spot-diagram, using real optical surfaces and guaranteeing the mechanical precision necessary for an optical system.

  5. Efficient, tunable flip-chip-integrated III-V/Si hybrid external-cavity laser array.

    Science.gov (United States)

    Lin, Shiyun; Zheng, Xuezhe; Yao, Jin; Djordjevic, Stevan S; Cunningham, John E; Lee, Jin-Hyoung; Shubin, Ivan; Luo, Ying; Bovington, Jock; Lee, Daniel Y; Thacker, Hiren D; Raj, Kannan; Krishnamoorthy, Ashok V

    2016-09-19

    We demonstrate a surface-normal coupled tunable hybrid silicon laser array for the first time using passively-aligned, high-accuracy flip chip bonding. A 2x6 III-V reflective semiconductor optical amplifier (RSOA) array with integrated total internal reflection mirrors is bonded to a CMOS SOI chip with grating couplers and silicon ring reflectors to form a tunable hybrid external-cavity laser array. Waveguide-coupled wall plug efficiency (wcWPE) of 2% and output power of 3 mW has been achieved for all 12 lasers. We further improved the performance by reducing the thickness of metal/dielectric stacks and achieved 10mW output power and 5% wcWPE with the same integration techniques. This non-invasive, one-step back end of the line (BEOL) integration approach provides a promising solution to high density laser sources for future large-scale photonic integrated circuits.

  6. Hybrid Optical Unobtrusive Blood Pressure Measurements

    Directory of Open Access Journals (Sweden)

    Guangfei Zhang

    2017-07-01

    Full Text Available Blood pressure (BP is critical in diagnosing certain cardiovascular diseases such as hypertension. Some previous studies have proved that BP can be estimated by pulse transit time (PTT calculated by a pair of photoplethysmography (PPG signals at two body sites. Currently, contact PPG (cPPG and imaging PPG (iPPG are two feasible ways to obtain PPG signals. In this study, we proposed a hybrid system (called the ICPPG system employing both methods that can be implemented on a wearable device, facilitating the measurement of BP in an inconspicuous way. The feasibility of the ICPPG system was validated on a dataset with 29 subjects. It has been proved that the ICPPG system is able to estimate PTT values. Moreover, the PTT measured by the new system shows a correlation on average with BP variations for most subjects, which could facilitate a new generation of BP measurement using wearable and mobile devices.

  7. Piezo-phototronic UV/visible photosensing with optical-fiber-nanowire hybridized structures.

    Science.gov (United States)

    Wang, Zhaona; Yu, Ruomeng; Pan, Caofeng; Liu, Ying; Ding, Yong; Wang, Zhong Lin

    2015-03-04

    An optical-fiber-nanowire hybridized UV-visible photodetector (PD) is reported. The PD is designed to allow direct integration in optical communication systems without requiring the use of couplers via fiber-welding technology. The PD works in two modes: axial and off-axial illumination mode. By using the piezo-phototronic effect, the performance of the PD is enhanced/optimized by up to 718% in sensitivity and 2067% in photoresponsivity. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Integrated optic devices based on nonlinear optical polymers

    Science.gov (United States)

    van Tomme, Emmanuel; van Daele, Peter P.; Baets, Roel G.; Lagasse, Paul E.

    1991-03-01

    An examination is made of the state of the art of nonlinear optical polymeric materials in view of their potential advantages. It is shown that these organic materials have many attractive features compared to LiNbO3 and III-V semiconductors with regard to their use in integrated optic circuits, especially since the level of integration is ever increasing. Considering more specifically electro-optic devices, a description is given of some of the theoretical background and basic properties. These polymers have already demonstrated a very high and extremely fast electro-optic effect compared to LiNbO3. It is also shown how low-loss waveguides can be fabricated by using easy techniques such as direct UV bleaching. The performance of phase modulators, Mach-Zehnder interferometers, and 2 x 2 space switches built with such polymers is already very promising. The results described in this study indicate a rapid rate of progress made by this technology, and one can expect that polymers in general and NLO polymers in particular will play an increasingly important role in integrated optics.

  9. Design and investigation of a novel silicon/ferroelectric hybrid electro-optical microring modulator

    Science.gov (United States)

    Qi, Zhipeng; Hu, Guohua; Liu, Chang; Li, Lei; Yun, Binfeng; Zhang, Ruohu; Cui, Yiping

    2017-02-01

    A silicon (Si) and lanthanum-doped lead zirconium titanate (PLZT) hybrid microring modulator based on silicon-on-insulator (SOI) platform is designed theoretically and investigated numerically in this paper. The heterogeneous integration of PLZT film with Si material enables the waveguide to acquire both excellent electro-optical property and strong mode confinement capacity. Such hybrid microring modulator (100 μm in radius) has a PLZT rib-loaded cladding and is integrated with optimized tuning electrodes. The simulation results demonstrated that the Si/PLZT hybrid microring modulator could operate at 14 GHz with a relative high modulation efficiency (<0.8 V cm), which is much better than the other proposed Si/ferroelectric modulators. Meanwhile, under a driving voltage of 20 V, our modulator exhibits an extinction ratio of 32 dB at 1550.22 nm wavelength and a resonant wavelength tunability of 25 pm/V for TE mode. With these outstanding performances, the Si/PLZT hybrid microring modulator holds a great potential as a reliable on-chip device for optical communications and links.

  10. Optical image encryption using Kronecker product and hybrid phase masks

    Science.gov (United States)

    Kumar, Ravi; Bhaduri, Basanta

    2017-10-01

    In this paper, we propose a new technique for security enhancement in optical image encryption system. In this technique we have used the Kronecker product of two random matrices along with the double random phase encoding (DRPE) scheme in the Fresnel domain for optical image encryption. The phase masks used here are different than the random masks used in conventional DRPE scheme. These hybrid phase masks are generated by using the combination of random phase masks and a secondary image. For encryption, the input image is first randomized and then the DRPE in the Fresnel domain is performed using the hybrid phase masks. Secondly, the Kronecker product of two random matrices is multiplied with the DRPE output to get the final encoded image for transmission. The proposed technique consists of more unknown keys for enhanced security and robust against various attacks. The simulation results along with effects under various attacks are presented in support of the proposed technique.

  11. Integrated Optical Transmitter and Receiver

    Science.gov (United States)

    1981-09-18

    Laser Development --Further laser development await the servicing of the GaAlAs/GaAs MOCVD reactor (see section D). During this period, work focused on continued high-speed measurements of narrow-diffused stripe laser structures grown by MOCVD, to be implemented into the integrated transmitter structure. Problems Encountered and/or Anticipated Work continued on isolating causes for growth control problems encountered last month on the GaAlAs/GaAs MOCVD system. These include inability to accurately tune the properties of the GaAlAs

  12. Hybrid quantum systems for enhanced nonlinear optical susceptibilities

    CERN Document Server

    Sullivan, Dennis; Kuzyk, Mark G

    2016-01-01

    Significant effort has been expended in the search for materials with ultra-fast nonlinear-optical susceptibilities, but most fall far below the fundamental limits. This work applies a theoretical materials development program that has identified a promising new hybrid made of a nanorod and a molecule. This system uses the electrostatic dipole moment of the molecule to break the symmetry of the metallic nanostructure that shifts the energy spectrum to make it optimal for a nonlinear-optical response near the fundamental limit. The structural parameters are varied to determine the ideal configuration, providing guidelines for making the best structures.

  13. Hybrid Microfluidic Platform for Multifactorial Analysis Based on Electrical Impedance, Refractometry, Optical Absorption and Fluorescence

    Directory of Open Access Journals (Sweden)

    Fábio M. Pereira

    2016-10-01

    Full Text Available This paper describes the development of a novel microfluidic platform for multifactorial analysis integrating four label-free detection methods: electrical impedance, refractometry, optical absorption and fluorescence. We present the rationale for the design and the details of the microfabrication of this multifactorial hybrid microfluidic chip. The structure of the platform consists of a three-dimensionally patterned polydimethylsiloxane top part attached to a bottom SU-8 epoxy-based negative photoresist part, where microelectrodes and optical fibers are incorporated to enable impedance and optical analysis. As a proof of concept, the chip functions have been tested and explored, enabling a diversity of applications: (i impedance-based identification of the size of micro beads, as well as counting and distinguishing of erythrocytes by their volume or membrane properties; (ii simultaneous determination of the refractive index and optical absorption properties of solutions; and (iii fluorescence-based bead counting.

  14. Integrated control platform for converged optical and wireless networks

    DEFF Research Database (Denmark)

    Yan, Ying

    the complementary characteristics of the optical networks and the wireless networks, addresses motivations for their interworking, discusses the current progress in hybrid network architectures as well as the functionalities of a control system, and identifies the achieved research contributions in the integrated...... are distributed based on the network states, channel conditions, and QoS requirements. A new aspect in the design of future network is the energy efficiency. An energy management mechanism is proposed and evaluated for the optical network. With regard to power saving, a sleep mode operation is developed....... Therefore, power is conserved by switch off some operating functions. The sleep period and wake up period are computed and assigned using two alternative scheduling schemes, which show trade-off performances on energy efficiency, queuing delay and network bandwidth utilization. To summarize...

  15. Materials and integration schemes for above-IC integrated optics

    NARCIS (Netherlands)

    Schmitz, Jurriaan; Rangarajan, Balaji; Kovalgin, Alexey Yu

    2014-01-01

    A study is presented on silicon oxynitride material for waveguides and germanium-silicon alloys for p-i-n diodes. The materials are manufactured at low, CMOS-backend compatible temperatures, targeting the integration of optical functions on top of CMOS chips. Low-temperature germanium-silicon deposi

  16. Integrated Optical Asymmetric Coupler Pressure Sensor

    Science.gov (United States)

    Kiyat, Isa; Kocabas, Coskun; Aydinli, Atilla

    2004-05-01

    Analysis of a novel pressure sensor based on a silicon-on-insulator (SOI) asymmetric vertical coupler is presented. The integrated optical component is a coupler composed of a single mode (SM) low index waveguide and a thin silicon slab. High sensitivities of about 0.14 rad.kPa-1 should be achieved.

  17. Integrated optical sensors for the chemical domain

    NARCIS (Netherlands)

    Lambeck, Paul V.

    2006-01-01

    During the last decade there has been a rapidly growing interest in integrated optical (IO) sensors, expecially because many of them principally allow for sensitive, real time, label-free-on-site measurements of the concentration of (bio-)chemical species. This review aims at giving an overview of t

  18. Integrated optical sensors for the chemical domain

    NARCIS (Netherlands)

    Lambeck, Paul

    2006-01-01

    During the last decade there has been a rapidly growing interest in integrated optical (IO) sensors, expecially because many of them principally allow for sensitive, real time, label-free-on-site measurements of the concentration of (bio-)chemical species. This review aims at giving an overview of t

  19. Universal discrete Fourier optics RF photonic integrated circuit architecture.

    Science.gov (United States)

    Hall, Trevor J; Hasan, Mehedi

    2016-04-04

    This paper describes a coherent electro-optic circuit architecture that generates a frequency comb consisting of N spatially separated orders using a generalised Mach-Zenhder interferometer (MZI) with its N × 1 combiner replaced by an optical N × N Discrete Fourier Transform (DFT). Advantage may be taken of the tight optical path-length control, component and circuit symmetries and emerging trimming algorithms offered by photonic integration in any platform that offers linear electro-optic phase modulation such as LiNbO3, silicon, III-V or hybrid technology. The circuit architecture subsumes all MZI-based RF photonic circuit architectures in the prior art given an appropriate choice of output port(s) and dimension N although the principal application envisaged is phase correlated subcarrier generation for all optical orthogonal frequency division multiplexing. A transfer matrix approach is used to model the operation of the architecture. The predictions of the model are validated by simulations performed using an industry standard software tool. Implementation is found to be practical.

  20. Integrated Miniature Arrays of Optical Biomolecule Detectors

    Science.gov (United States)

    Iltchenko, Vladimir; Maleki, Lute; Lin, Ying; Le, Thanh

    2009-01-01

    Integrated miniature planar arrays of optical sensors for detecting specific biochemicals in extremely small quantities have been proposed. An array of this type would have an area of about 1 cm2. Each element of the array would include an optical microresonator that would have a high value of the resonance quality factor (Q . 107). The surface of each microresonator would be derivatized to make it bind molecules of a species of interest, and such binding would introduce a measurable change in the optical properties of the microresonator. Because each microresonator could be derivatized for detection of a specific biochemical different from those of the other microresonators, it would be possible to detect multiple specific biochemicals by simultaneous or sequential interrogation of all the elements in the array. Moreover, the derivatization would make it unnecessary to prepare samples by chemical tagging. Such interrogation would be effected by means of a grid of row and column polymer-based optical waveguides that would be integral parts of a chip on which the array would be fabricated. The row and column polymer-based optical waveguides would intersect at the elements of the array (see figure). At each intersection, the row and column waveguides would be optically coupled to one of the microresonators. The polymer-based waveguides would be connected via optical fibers to external light sources and photodetectors. One set of waveguides and fibers (e.g., the row waveguides and fibers) would couple light from the sources to the resonators; the other set of waveguides and fibers (e.g., the column waveguides and fibers) would couple light from the microresonators to the photodetectors. Each microresonator could be addressed individually by row and column for measurement of its optical transmission. Optionally, the chip could be fabricated so that each microresonator would lie inside a microwell, into which a microscopic liquid sample could be dispensed.

  1. Hybrid state-space time integration of rotating beams

    DEFF Research Database (Denmark)

    Krenk, Steen; Nielsen, Martin Bjerre

    2012-01-01

    An efficient time integration algorithm for the dynamic equations of flexible beams in a rotating frame of reference is presented. The equations of motion are formulated in a hybrid state-space format in terms of local displacements and local components of the absolute velocity. With inspiration ...

  2. Hybrid polymer photonic crystal fiber with integrated chalcogenide glass nanofilms

    DEFF Research Database (Denmark)

    Markos, Christos; Kubat, Irnis; Bang, Ole

    2014-01-01

    The combination of chalcogenide glasses with polymer photonic crystal fibers (PCFs) is a difficult and challenging task due to their different thermo-mechanical material properties. Here we report the first experimental realization of a hybrid polymer-chalcogenide PCF with integrated As2S3 glass ...

  3. Optical waveguides using PDMS-metal oxide hybrid nanocomposites

    Science.gov (United States)

    Hosseinzadeh, Arash; Middlebrook, Christopher T.; Mullins, Michael E.

    2015-03-01

    Development of passive and active polymer based optical materials for high data rate waveguide routing and interconnects has gained increased attention because of their excellent properties such as low absorption, cost savings, and ease in fabrication. However, optical polymers are typically limited in the range of their refraction indices. Combining polymeric and inorganic optical materials provides advantages for as development of nano-composites with higher refractive indices with the possibility of being used as an active optical component. In this paper a new composite material is proposed based on polymer-metal oxide nano-composites for use as optical wave guiding structures and components. PDMS (Polydimethylsiloxane) is utilized for the polymer portion while the inorganic material is titanium dioxide. Refraction indices as high as 1.74 have been reported using these composites. For PDMS-TiO2 hybrids, the higher the ratio of titanium dioxide to PDMS, the higher the resulting refractive index. The index of refraction as a function of the PDMS:TiO2 ratio is reported with an emphasis on use as optical waveguide devices. Absorption spectrum of the nano-composites is measured showing low absorption at 850 nm and high absorption in the UV regime for direct UV laser/light curing. Prototype multimode waveguides are fabricated using soft imprint embossing that is compatible with the low viscosity nano-composite material. Cross dimensional shape and profile show the potential for full scale development utilizing the material set.

  4. Performance analysis of a hybrid fingerprint extracted from optical coherence tomography fingertip scans

    CSIR Research Space (South Africa)

    Darlow, Luke N

    2016-06-01

    Full Text Available International Conference on Biometrics (ICB), 13-16 June 2016, Halmstad, Sweden Performance analysis of a hybrid fingerprint extracted from optical coherence tomography fingertip scans Darlow LN Connan J Singh A ABSTRACT: The Hybrid fingerprint is a...

  5. Integrated optics dissipative soliton mode-locked laser on glass

    Science.gov (United States)

    Charlet, Bertrand; Bastard, Lionel; Broquin, Jean-Emmanuel

    2011-01-01

    Mode-lock lasers have been studied a lot in the past years for producing pulses as short as possible. These devices have mostly been realized in bulk optics and they are consequently cumbersome and sensitive to vibrations. There are only a few studies on integrated optics mode-lock lasers, though this technology is very promising because of its stability, compactness and the possibility to integrate several functions on a single chip. In this paper, we present an ion-exchange passively mode-locked laser in dissipative soliton operation. One of the key characteristics of this structure is its mechanical stability. Indeed, no bulk optics is needed because the saturable absorber is hybridized on the top of the waveguide in order to interact with the evanescent part of the guided mode. Indeed, the device that has been obtained is composed of an ion-exchanged single mode waveguide realized in a Neodymium doped phosphate glass. The laser feedback is produced by a Fabry-Perot cavity realized with two multilayers dielectric mirrors stuck on the waveguides facets. We implemented a bis(4- dimethylaminodithiobenzil)nickel (BDN) dye included in a cellulose acetate thick film, which presents a saturable absorber behaviour around 1.06 μm. With this structure, pulses with repetition rates of 3.3 GHz and a single mode output have been measured. Moreover, the use of an autocorrelation set-up allowed us measuring picosecond pulse durations.

  6. Silver nanoprisms/silicone hybrid rubber materials and their optical limiting property to femtosecond laser

    Science.gov (United States)

    Li, Chunfang; Liu, Miao; Jiang, Nengkai; Wang, Chunlei; Lin, Weihong; Li, Dongxiang

    2017-08-01

    Optical limiters against femtosecond laser are essential for eye and sensor protection in optical processing system with femtosecond laser as light source. Anisotropic Ag nanoparticles are expected to develop into optical limiting materials for femtosecond laser pulses. Herein, silver nanoprisms are prepared and coated by silica layer, which are then doped into silicone rubber to obtain hybrid rubber sheets. The silver nanoprisms/silicone hybrid rubber sheets exhibit good optical limiting property to femtosecond laser mainly due to nonlinear optical absorption.

  7. High-Capacity Hybrid Optical Fiber-Wireless Communications Links in Access Networks

    DEFF Research Database (Denmark)

    Pang, Xiaodan

    techniques with both coherent and incoherent optical sources are studied and demonstrated. Employments of advanced modulation formats including phase-shift keying (PSK), M-quadrature amplitude modulation (QAM) and orthogonal frequency-division multiplexing (OFDM) for high speed photonic-wireless transmission......Integration between fiber-optic and wireless communications systems in the "last mile" access networks is currently considered as a promising solution for both service providers and users, in terms of minimizing deployment cost, shortening upgrading period and increasing mobility and flexibility...... techniques. In conclusion, the results presented in the thesis show the feasibility of employing mm-wave signals, advanced modulation formats and spatial multiplexing technologies in next generation high capacity hybrid optical fiber-wireless access systems....

  8. Multicomponent glass fiber optic integrated structures

    Science.gov (United States)

    Pysz, Dariusz; Kujawa, Ireneusz; Szarniak, Przemyslaw; Franczyk, Marcin; Stepien, Ryszard; Buczynski, Ryszard

    2005-09-01

    A range of integrated fiber optic structures - lightguides, image guides, multicapillary arrays, microstructured (photonic) fibers - manufactured in the Institute of Electronic Materials Technology (ITME) is described. All these structures are made of multicomponent glasses (a part of them melted in ITME). They can be manufactured in similar multistep process that involves drawing glass or lightguide rods and tubes preparing glass performs, stacking a bundle with rods and (or) tubes, drawing multifiber or multicapillary performs. Structure formation, technological process, characterization and applications of different integrated structures are presented.

  9. Ultra Small Integrated Optical Fiber Sensing System

    Directory of Open Access Journals (Sweden)

    Peter Van Daele

    2012-09-01

    Full Text Available This paper introduces a revolutionary way to interrogate optical fiber sensors based on fiber Bragg gratings (FBGs and to integrate the necessary driving optoelectronic components with the sensor elements. Low-cost optoelectronic chips are used to interrogate the optical fibers, creating a portable dynamic sensing system as an alternative for the traditionally bulky and expensive fiber sensor interrogation units. The possibility to embed these laser and detector chips is demonstrated resulting in an ultra thin flexible optoelectronic package of only 40 μm, provided with an integrated planar fiber pigtail. The result is a fully embedded flexible sensing system with a thickness of only 1 mm, based on a single Vertical-Cavity Surface-Emitting Laser (VCSEL, fiber sensor and photodetector chip. Temperature, strain and electrodynamic shaking tests have been performed on our system, not limited to static read-out measurements but dynamically reconstructing full spectral information datasets.

  10. Load balancing in integrated optical wireless networks

    DEFF Research Database (Denmark)

    Yan, Ying; Dittmann, Lars; Wong, S-W.;

    2010-01-01

    In this paper, we tackle the load balancing problem in Integrated Optical Wireless Networks, where cell breathing technique is used to solve congestion by changing the coverage area of a fully loaded cell tower. Our objective is to design a load balancing mechanism which works closely with the in......In this paper, we tackle the load balancing problem in Integrated Optical Wireless Networks, where cell breathing technique is used to solve congestion by changing the coverage area of a fully loaded cell tower. Our objective is to design a load balancing mechanism which works closely...... issues are outlined and a cost function based optimization model is developed for power management. In particularly, two alternative feedback schemes are proposed to report wireless network status. Simulation results show that our proposed load balancing mechanism improves network performances....

  11. Compact Hybrid Subsystem of 16 Channel Optical Demultiplexer, 2x2 Switches, Optical Power Monitors and Control Circuit

    Institute of Scientific and Technical Information of China (English)

    Kenichiro Takahashi; Toshihiko Kishimoto; Shintaro Mouri; Youichi Hata; Hideaki Yusa; Mitsuaki Tamura; Kazuhito Saito; Hisao Maki

    2003-01-01

    A compact hybrid subsystem of 16channel optical demultiplexer, 2x2 switches, optical power monitors and control circuit board is developed. The subsystem is able to add or drop arbitrary optical channels and monitor the optical power level by software commands. The size of the subsystem is 170x200x30(mm).

  12. Moving the boundary between wavelength resources in optical packet and circuit integrated ring network.

    Science.gov (United States)

    Furukawa, Hideaki; Miyazawa, Takaya; Wada, Naoya; Harai, Hiroaki

    2014-01-13

    Optical packet and circuit integrated (OPCI) networks provide both optical packet switching (OPS) and optical circuit switching (OCS) links on the same physical infrastructure using a wavelength multiplexing technique in order to deal with best-effort services and quality-guaranteed services. To immediately respond to changes in user demand for OPS and OCS links, OPCI networks should dynamically adjust the amount of wavelength resources for each link. We propose a resource-adjustable hybrid optical packet/circuit switch and transponder. We also verify that distributed control of resource adjustments can be applied to the OPCI ring network testbed we developed. In cooperation with the resource adjustment mechanism and the hybrid switch and transponder, we demonstrate that automatically allocating a shared resource and moving the wavelength resource boundary between OPS and OCS links can be successfully executed, depending on the number of optical paths in use.

  13. Optical integration of CAD/CAM materials.

    Science.gov (United States)

    Güth, Jan-Frederik; Magne, Pascal

    The optical integration (OI) of monolithic CAD/CAM materials under 4 illuminations was evaluated using a standardized and clinically relevant method. Eighteen inlays were manufactured and placed (glycerin gel). Standardized photos were taken under 4 illuminations (neutral white light direct and indirect illumination, cross-polarized light, fluorescent light). Six evaluators defined the optical integration score (OIS) as the "visibility" of the restoration (0 = worst OI, 4 = optimal OI). The intact tooth served as control. The null hypothesis was that different illuminations did not influence the OI of CAD/CAM inlays. One-way ANOVA, followed by Scheffe's post hoc, was applied (P = 0.05). Neutral light direct illumination: OIS between 2.67 (IPS e.max CAD LT A1, ENAMIC A1) and 3.83 (IPS e.max CAD HT A1) with a mean of 3.28 (± 0.339). Indirect illumination: OIS from 1.00 (Paradigm MZ100 A1) to 2.41 (ENAMIC A1) with a mean of 1.88 (± 0.598). Fluorescent light: OIS between 0.75 and 3.25 with a mean of 1.67 (± 1.025). ENAMIC and VITA BLOCS Mark II showed the best optical integration in fluorescence. IPS e.max CAD, Paradigm MZ 100 demonstrated low fluorescence; Lava Ultimate high fluorescence. OI was influenced by different illumination. A simple method accessible to clinicians for additional evaluation of CAD/CAM materials in daily practice is presented. All materials showed excellent OI under direct illumination with neutral white light. The most pronounced differences in optical integration between tooth and evaluated materials were observed under fluorescent light.

  14. Monolithically integrated interferometer for optical displacement measurement

    Science.gov (United States)

    Hofstetter, Daniel; Zappe, Hans P.

    1996-01-01

    We discuss the fabrication of a monolithically integrated optical displacement sensors using III-V semiconductor technology. The device is configured as a Michelson interferometer and consists of a distributed Bragg reflector laser, a photodetector and waveguides forming a directional coupler. Using this interferometer, displacements in the 100 nm range could be measured at distances of up to 45 cm. We present fabrication, device results and characterization of the completed interferometer, problems, limitations and future applications will also be discussed.

  15. Design and construction of a VHGT-attached WDM-type triplex transceiver module using polymer PLC hybrid integration technology

    Science.gov (United States)

    Jerábek, Vitezslav; Hüttel, Ivan; Prajzler, Václav; Busek, K.; Seliger, P.

    2008-11-01

    We report about design and construction of the bidirectional transceiver TRx module for subscriber part of the passive optical network PON for a fiber to the home FTTH topology. The TRx module consists of a epoxy novolak resin polymer planar lightwave circuit (PLC) hybrid integration technology with volume holographic grating triplex filter VHGT, surface-illuminated photodetectors and spot-size converted Fabry-Pérot laser diode in SMD package. The hybrid PLC has composed from a two parts-polymer optical waveguide including VHGT filter section and a optoelectronic microwave section. The both parts are placed on the composite substrate.

  16. Nanostructured Fiber Optic Cantilever Arrays and Hybrid MEMS Sensors for Chemical and Biological Detection Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advancements in nano-/micro-scale sensor fabrication and molecular recognition surfaces offer promising opportunities to develop miniaturized hybrid fiber optic and...

  17. Hybrid Microfluidic Platform for Multifactorial Analysis Based on Electrical Impedance, Refractometry, Optical Absorption and Fluorescence

    National Research Council Canada - National Science Library

    Pereira, Fábio; Bernacka-Wojcik, Iwona; Ribeiro, Rita; Lobato, Maria; Fortunato, Elvira; Martins, Rodrigo; Igreja, Rui; Jorge, Pedro; Águas, Hugo; Oliva, Abel

    2016-01-01

    ...: electrical impedance, refractometry, optical absorption and fluorescence. We present the rationale for the design and the details of the microfabrication of this multifactorial hybrid microfluidic chip...

  18. Collimating slicer for optical integral field spectroscopy

    Science.gov (United States)

    Laurent, Florence; Hénault, François

    2016-07-01

    Integral Field Spectroscopy (IFS) is a technique that gives simultaneously the spectrum of each spatial sampling element of a given field. It is a powerful tool which rearranges the data cube represented by two spatial dimensions defining the field and the spectral decomposition (x, y, λ) in a detector plane. In IFS, the "spatial" unit reorganizes the field, the "spectral" unit is being composed of a classical spectrograph. For the spatial unit, three main techniques - microlens array, microlens array associated with fibres and image slicer - are used in astronomical instrumentations. The development of a Collimating Slicer is to propose a new type of optical integral field spectroscopy which should be more compact. The main idea is to combine the image slicer with the collimator of the spectrograph mixing the "spatial" and "spectral" units. The traditional combination of slicer, pupil and slit elements and spectrograph collimator is replaced by a new one composed of a slicer and spectrograph collimator only. After testing few configurations, this new system looks very promising for low resolution spectrographs. In this paper, the state of art of integral field spectroscopy using image slicers will be described. The new system based onto the development of a Collimating Slicer for optical integral field spectroscopy will be depicted. First system analysis results and future improvements will be discussed.

  19. Self-Healing Hybrid Protection Architecture for Passive Optical Networks

    Directory of Open Access Journals (Sweden)

    Waqas A. Imtiaz

    2015-08-01

    Full Text Available Expanding size of passive optical networks (PONs along with high availability expectation makes the reliability performance a crucial need. Most protection architectures utilize redundant network components to enhance network survivability, which is not economical. This paper proposes new self-healing protection architecture for passive optical networks (PONs, with a single ring topology and star-ring topology at feeder and distribution level respectively. The proposed architecture provides desirable protection to the network by avoiding fiber duplication at both feeder and distribution level. Moreover, medium access control (MAC controlled switching is utilized to provide efficient detection, and restoration of faults or cuts throughout the network. Analytical analysis reveals that the proposed self-healing hybrid protection architecture ensures survivability of the affected traffic along with desirable connection availability of 99.9994 % at minimum deployment cost, through simple architecture and simultaneous protection against failures.

  20. Hybrid electro-optical nanosystem for neurons investigation

    Science.gov (United States)

    Miu, Mihaela; Kleps, Irina; Craciunoiu, Florea; Simion, Monica; Bragaru, Adina; Ignat, Teodora

    2010-11-01

    The scope of this paper is development of a new laboratory-on-a-chip (LOC) device for biomedical studies consisting of a microfluidic system coupled to microelectronic/optical transducers with nanometric features, commonly called biosensors. The proposed device is a hybrid system with sensing element on silicon (Si) chip and microfluidic system on polydimethylsiloxane (PDMS) substrates, taking into accounts their particular advantages. Different types of nanoelectrode arrays, positioned in the reactor, have been investigated as sensitive elements for electrical detection and the recording of neuron extracellular electric activity has been monitorized in parallel with whole-cell patch-clamp membrane current. Moreover, using an additional porosification process the sensing element became efficient for optical detection also. The preliminary test results demonstrate the functionality of the proposed design and also the fabrication technology, the devices bringing advantages in terms enhancement of sensitivity in both optoelectronic detection schemes.

  1. All-optical quantum computing with a hybrid solid-state processing unit

    CERN Document Server

    Pei, Pei; Li, Chong

    2011-01-01

    We develop an architecture of hybrid quantum solid-state processing unit for universal quantum computing. The architecture allows distant and nonidentical solid-state qubits in distinct physical systems to interact and work collaboratively. All the quantum computing procedures are controlled by optical methods using classical fields and cavity QED. Our methods have prominent advantage of the insensitivity to dissipation process due to the virtual excitation of subsystems. Moreover, the QND measurements and state transfer for the solid-state qubits are proposed. The architecture opens promising perspectives for implementing scalable quantum computation in a broader sense that different solid systems can merge and be integrated into one quantum processor afterwards.

  2. Integration of active and passive polymer optics

    DEFF Research Database (Denmark)

    Christiansen, Mads Brøkner; Schøler, Mikkel; Kristensen, Anders

    2007-01-01

    protrusions and an integrated metal shadow mask. In the CNP process, a combined UV mask and nanoimprint stamp is embossed into the resist, which is softened by heating, and UV exposed. Hereby the mm to m m sized features are defined by the UV exposure through the metal mask, while nm-scale features are formed......We demonstrate a wafer scale fabrication process for integration of active and passive polymer optics: Polymer DFB lasers and waveguides. Polymer dye DFB lasers are fabricated by combined nanoimprint and photolithography (CNP). The CNP fabrication relies on an UV transparent stamp with nm sized...... by mechanical deformation (nanoimprinting). The lasers are integrated with undoped SU-8 polymer waveguides. The waferscale fabrication process has a yield above 90% and the emission wavelengths are reproduced within 2 nm. Confinement of the light on the chip is demonstrated, and the influence on the laser...

  3. Magneto-optical mode conversion in a hybrid glass waveguide made by sol-gel and ion-exchange techniques

    Science.gov (United States)

    Royer, François; Amata, Hadi; Parsy, François; Jamon, Damien; Ghibaudo, Elise; Broquin, Jean-Emmanuel; Neveu, Sophie

    2012-01-01

    The integration of magneto-optical materials with classical technologies being still a difficult problem, this study explores the possibility to realize a mode converter based on a hybrid structure. A composite magneto-optical layer made of a silica/zirconia matrix doped by magnetic nanoparticles is coated on the top face of ion-exchanged glass waveguides. Optical characterizations that have been carried out demonstrated the efficiency of these hybrid structures in terms of lateral confinement. Furthermore, TE to TM mode conversion has been observed when a longitudinal magnetic field is applied to the device. The amount of this conversion is analysed taking into account the magneto-optical confinement and the modal birefringence of the structure.

  4. Optical Nanofiber Integrated into Optical Tweezers for In Situ Fiber Probing and Optical Binding Studies

    Directory of Open Access Journals (Sweden)

    Ivan Gusachenko

    2015-07-01

    Full Text Available Precise control of particle positioning is desirable in many optical propulsion and sorting applications. Here, we develop an integrated platform for particle manipulation consisting of a combined optical nanofiber and optical tweezers system. We show that consistent and reversible transmission modulations arise when individual silica microspheres are introduced to the nanofiber surface using the optical tweezers. The observed transmission changes depend on both particle and fiber diameter and can be used as a reference point for in situ nanofiber or particle size measurement. Thence, we combine scanning electron microscope (SEM size measurements with nanofiber transmission data to provide calibration for particle-based fiber assessment. This integrated optical platform provides a method for selective evanescent field manipulation of micron-sized particles and facilitates studies of optical binding and light-particle interaction dynamics.

  5. Hybrid Wavelength Routed and Optical Packet Switched Ring Networks for the Metropolitan Area Network

    DEFF Research Database (Denmark)

    Nord, Martin

    2005-01-01

    Increased data traffic in the metropolitan area network calls for new network architectures. This paper evaluates optical ring architectures based on optical packet switching, wavelength routing, and hybrid combinations of the two concepts. The evaluation includes overall throughput and fairness...

  6. Silicon Carbide Lightweight Optics With Hybrid Skins for Large Cryo Telescopes Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Optical Physics Company (OPC) has developed new silicon carbide (SiC) foam-based optics with hybrid skins that are composite, athermal and lightweight (FOCAL) that...

  7. Active materials for integrated optic applications

    Science.gov (United States)

    Hayden, Joseph S.; Funk, David S.; Veasey, David L.; Peters, Philip M.; Sanford, Norman A.

    1999-11-01

    The ability to engineer glass properties through the selection and adjustment of chemical composition continues to make glass a leading material in both active and passive applications. The development of optimal glass compositions for integrated optical applications requires a number of considerations that are often at variance with one another. Of critical importance is that the glass offers compatibility with standard ion exchange technologies, allowing fabrication of guided wave structures. In addition, for application as an active material, the resultant structures must be characterized by absence of inclusions and low absorption at the lasing wavelength, putting demands on both the selection and identity of the raw materials used to prepare the glass. We report on the development of an optimized glass composition for integrated optic applications that combines good laser properties with good chemical durability allowing for a wide range of chemical processing steps to be employed without substrate deterioration. In addition, care was taken during the development of this glass to insure that the selected composition was consistent with manufacturing technology for producing high optical quality glass. We present the properties of the resultant glasses, including results of detailed chemical and laser properties, for use in the design and modeling of active waveguides prepared with these glasses.

  8. MPACVD processing technologies for planar integrated optics

    Science.gov (United States)

    Li, Cheng-Chung; Boudreau, Robert A.; Bowen, Terry P.

    1998-06-01

    Optical circuits based on low-loss glass waveguide are the practical and promising approaches to integrate different functional components for optical communication system. Microwave plasma assisted chemical vapor deposition produces superior quality, low birefringence, low-loss, planar waveguides for integrated optical devices. A microwave plasma initiates the chemical vapor of SiCl4, GeCl4 and oxygen. A Ge-doped silica layer thus deposited on the substrates with reasonable high growth rate. Film properties are based on various parameters, such as chemical flow rates, chamber pressure and temperature, power level and injector design. The main emphasis has been on optimizing the deposition parameters and reproducibility. An uniform, low-loss film can be made by properly balancing the precursor flows. The refractive index of deposited film can also be controlled by adjusting the flow ratio of SiCl4 and GeCl4 bubblers. Deposited films was characterized by prism coupler, loss measurement, residual stress, and composition analysis. The resulted refractive index step can be varied between 1.46 to 1.60. Waveguide can be fabricated with any desired refractive index profile. Standard photolithography defines the waveguide pattern on mask layer. Core layer was remove by the plasma dry etch which has been investigated by both reactive ion etch (RIE) and inductively coupled plasma etch. Etch rate of 3000-4000 angstrom/min has been achieved by using ICP compared to typical etch rate of 200-300 angstrom/min by using conventional RIE.

  9. Optimization of hybrid antireflection structure integrating surface texturing and multi-layer interference coating

    Science.gov (United States)

    Kubota, Shigeru; Kanomata, Kensaku; Suzuki, Takahiko; Hirose, Fumihiko

    2014-10-01

    The antireflection structure (ARS) for solar cells is categorized to mainly two different techniques, i.e., the surface texturing and the single or multi-layer antireflection interference coating. In this study, we propose a novel hybrid ARS, which integrates moth eye texturing and multi-layer coat, for application to organic photovoltaics (OPVs). Using optical simulations based on the finite-difference time-domain (FDTD) method, we conduct nearly global optimization of the geometric parameters characterizing the hybrid ARS. The proposed optimization algorithm consists of two steps: in the first step, we optimize the period and height of moth eye array, in the absence of multi-layer coating. In the second step, we optimize the whole structure of hybrid ARS by using the solution obtained by the first step as the starting search point. The methods of the simple grid search and the Hooke and Jeeves pattern search are used for global and local searches, respectively. In addition, we study the effects of deviations in the geometric parameters of hybrid ARS from their optimized values. The design concept of hybrid ARS is highly beneficial for broadband light trapping in OPVs.

  10. Hybrid CMOS/Nanodevice Integrated Circuits Design and Fabrication

    Science.gov (United States)

    2008-08-25

    This approach combines a semiconductor transistor system with a nanowire crossbar, with simple two-terminal nanodevices self-assembled at each...hybrid CMOS/nanodevice integrated circuits [10-12]. Such circuit combines a semiconductor transistors system with a nanowire crossbar, with simple two...both with and without embedded metallic clusters), self-assembled molecular monolayers, and thin chalcogenide and crystalline perovskite layers [20

  11. Completely integrable models of nonlinear optics

    Indian Academy of Sciences (India)

    Andrey I Maimistov

    2001-11-01

    The models of the nonlinear optics in which solitons appeared are considered. These models are of paramount importance in studies of nonlinear wave phenomena. The classical examples of phenomena of this kind are the self-focusing, self-induced transparency and parametric interaction of three waves. At present there are a number of theories based on completely integrable systems of equations, which are, both, generations of the original known models and new ones. The modified Korteweg-de Vries equation, the nonlinear Schrödinger equation, the derivative nonlinear Schrödinger equation, Sine–Gordon equation, the reduced Maxwell–Bloch equation, Hirota equation, the principal chiral field equations, and the equations of massive Thirring model are some soliton equations, which are usually to be found in nonlinear optics theory.

  12. 3D integral imaging with optical processing

    Science.gov (United States)

    Martínez-Corral, Manuel; Martínez-Cuenca, Raúl; Saavedra, Genaro; Javidi, Bahram

    2008-04-01

    Integral imaging (InI) systems are imaging devices that provide auto-stereoscopic images of 3D intensity objects. Since the birth of this new technology, InI systems have faced satisfactorily many of their initial drawbacks. Basically, two kind of procedures have been used: digital and optical procedures. The "3D Imaging and Display Group" at the University of Valencia, with the essential collaboration of Prof. Javidi, has centered its efforts in the 3D InI with optical processing. Among other achievements, our Group has proposed the annular amplitude modulation for enlargement of the depth of field, dynamic focusing for reduction of the facet-braiding effect, or the TRES and MATRES devices to enlarge the viewing angle.

  13. Monolithically integrated quantum dot optical modulator with Semiconductor optical amplifier for short-range optical communications

    Science.gov (United States)

    Yamamoto, Naokatsu; Akahane, Kouichi; Umezawa, Toshimasa; Kawanishi, Tetsuya

    2015-04-01

    A monolithically integrated quantum dot (QD) optical gain modulator (OGM) with a QD semiconductor optical amplifier (SOA) was successfully developed. Broadband QD optical gain material was used to achieve Gbps-order high-speed optical data transmission, and an optical gain change as high as approximately 6-7 dB was obtained with a low OGM voltage of 2.0 V. Loss of optical power due to insertion of the device was also effectively compensated for by the SOA section. Furthermore, it was confirmed that the QD-OGM/SOA device helped achieve 6.0-Gbps error-free optical data transmission over a 2.0-km-long photonic crystal fiber. We also successfully demonstrated generation of Gbps-order, high-speed, and error-free optical signals in the >5.5-THz broadband optical frequency bandwidth larger than the C-band. These results suggest that the developed monolithically integrated QD-OGM/SOA device will be an advantageous and compact means of increasing the usable optical frequency channels for short-reach communications.

  14. Hybrid liquid crystals: Enhanced electro-optic and nonlinear response for manipulating beams (Conference Presentation)

    Science.gov (United States)

    Kaczmarek, Malgosia; D'Alessandro, Giampaolo; Proctor, Matthew B.

    2016-09-01

    The manipulation and processing of light beams can be efficiently accomplished through devices based on soft matter placed in a hybrid "symbiosis" with other organic or inorganic, photoresponsive materials. The performance of such smart modulating systems often relies on a subtle balance between individual properties of each component, together with the varying interaction between organic and inorganic elements. Some promising demonstrations in the visible as well as in the THz regimes include liquid crystals integrated with plasmonic or ferroelectric nanoparticles, photoconductive or photosensitive polymers as well as metamaterials. They offer adaptive, flexible and tailor-made solutions for applications in displays and optoelectronics, switching, steering and modulating electromagnetic waves. Hybrid configurations that include multiple photoresponsive layers, sandwiched with liquid crystals, led to stronger modulation and steering of light beams in the visible. Such effects can also be observed in the other regions of spectrum, as inorganic nanoparticles dispersed in liquid crystals modify the magnitude of the material refractive indices measured in THz. The development of such hybrid materials has to be accompanied by comprehensive characterisation of their uniformity, stability and optical quality across the whole surface of the device, capable of determining their optical, electrical and physical parameters.

  15. One-dimensional photonic crystal slot waveguide for silicon-organic hybrid electro-optic modulators.

    Science.gov (United States)

    Yan, Hai; Xu, Xiaochuan; Chung, Chi-Jui; Subbaraman, Harish; Pan, Zeyu; Chakravarty, Swapnajit; Chen, Ray T

    2016-12-01

    In an on-chip silicon-organic hybrid electro-optic (EO) modulator, the mode overlap with EO materials, in-device effective r33, and propagation loss are among the most critical factors that determine the performance of the modulator. Various waveguide structures have been proposed to optimize these factors, yet there is a lack of comprehensive consideration on all of them. In this Letter, a one-dimensional (1D) photonic crystal (PC) slot waveguide structure is proposed that takes all these factors into consideration. The proposed structure takes advantage of the strong mode confinement within a low-index region in a conventional slot waveguide and the slow-light enhancement from the 1D PC structure. Its simple geometry makes it robust to resist fabrication imperfections and helps reduce the propagation loss. Using it as a phase shifter in a Mach-Zehnder interferometer structure, an integrated silicon-organic hybrid EO modulator was experimentally demonstrated. The observed effective EO coefficient is as high as 490 pm/V. The measured half-wave voltage and length product is less than 1  V·cm and can be further improved. A potential bandwidth of 61 GHz can be achieved and further improved by tailoring the doping profile. The proposed structure offers a competitive novel phase-shifter design, which is simple, highly efficient, and with low optical loss, for on-chip silicon-organic hybrid EO modulators.

  16. Graphene/Si CMOS hybrid hall integrated circuits.

    Science.gov (United States)

    Huang, Le; Xu, Huilong; Zhang, Zhiyong; Chen, Chengying; Jiang, Jianhua; Ma, Xiaomeng; Chen, Bingyan; Li, Zishen; Zhong, Hua; Peng, Lian-Mao

    2014-07-07

    Graphene/silicon CMOS hybrid integrated circuits (ICs) should provide powerful functions which combines the ultra-high carrier mobility of graphene and the sophisticated functions of silicon CMOS ICs. But it is difficult to integrate these two kinds of heterogeneous devices on a single chip. In this work a low temperature process is developed for integrating graphene devices onto silicon CMOS ICs for the first time, and a high performance graphene/CMOS hybrid Hall IC is demonstrated. Signal amplifying/process ICs are manufactured via commercial 0.18 um silicon CMOS technology, and graphene Hall elements (GHEs) are fabricated on top of the passivation layer of the CMOS chip via a low-temperature micro-fabrication process. The sensitivity of the GHE on CMOS chip is further improved by integrating the GHE with the CMOS amplifier on the Si chip. This work not only paves the way to fabricate graphene/Si CMOS Hall ICs with much higher performance than that of conventional Hall ICs, but also provides a general method for scalable integration of graphene devices with silicon CMOS ICs via a low-temperature process.

  17. Graphene/Si CMOS Hybrid Hall Integrated Circuits

    Science.gov (United States)

    Huang, Le; Xu, Huilong; Zhang, Zhiyong; Chen, Chengying; Jiang, Jianhua; Ma, Xiaomeng; Chen, Bingyan; Li, Zishen; Zhong, Hua; Peng, Lian-Mao

    2014-07-01

    Graphene/silicon CMOS hybrid integrated circuits (ICs) should provide powerful functions which combines the ultra-high carrier mobility of graphene and the sophisticated functions of silicon CMOS ICs. But it is difficult to integrate these two kinds of heterogeneous devices on a single chip. In this work a low temperature process is developed for integrating graphene devices onto silicon CMOS ICs for the first time, and a high performance graphene/CMOS hybrid Hall IC is demonstrated. Signal amplifying/process ICs are manufactured via commercial 0.18 um silicon CMOS technology, and graphene Hall elements (GHEs) are fabricated on top of the passivation layer of the CMOS chip via a low-temperature micro-fabrication process. The sensitivity of the GHE on CMOS chip is further improved by integrating the GHE with the CMOS amplifier on the Si chip. This work not only paves the way to fabricate graphene/Si CMOS Hall ICs with much higher performance than that of conventional Hall ICs, but also provides a general method for scalable integration of graphene devices with silicon CMOS ICs via a low-temperature process.

  18. Integrated optical addressing of an ion qubit.

    Science.gov (United States)

    Mehta, Karan K; Bruzewicz, Colin D; McConnell, Robert; Ram, Rajeev J; Sage, Jeremy M; Chiaverini, John

    2016-12-01

    The long coherence times and strong Coulomb interactions afforded by trapped ion qubits have enabled realizations of the necessary primitives for quantum information processing and the highest-fidelity quantum operations in any qubit to date. Although light delivery to each individual ion in a system is essential for general quantum manipulations and readout, experiments so far have employed optical systems that are cumbersome to scale to even a few tens of qubits. Here we demonstrate lithographically defined nanophotonic waveguide devices for light routing and ion addressing that are fully integrated within a surface-electrode ion trap chip. Ion qubits are addressed at multiple locations via focusing grating couplers emitting through openings in the trap electrodes to ions trapped 50 μm above the chip; using this light, we perform quantum coherent operations on the optical qubit transition in individual (88)Sr(+) ions. The grating focuses the beam to a diffraction-limited spot near the ion position with 2 μm 1/e(2) radius along the trap axis, and we measure crosstalk errors between 10(-2) and 4 × 10(-4) at distances 7.5-15 μm from the beam centre. Owing to the scalability of the planar fabrication technique employed, together with the tight focusing and stable alignment afforded by the integration of the optics within the trap chip, this approach presents a path to creating the optical systems required for large-scale trapped-ion quantum information processing.

  19. Integrated optical addressing of an ion qubit

    Science.gov (United States)

    Mehta, Karan K.; Bruzewicz, Colin D.; McConnell, Robert; Ram, Rajeev J.; Sage, Jeremy M.; Chiaverini, John

    2016-12-01

    The long coherence times and strong Coulomb interactions afforded by trapped ion qubits have enabled realizations of the necessary primitives for quantum information processing and the highest-fidelity quantum operations in any qubit to date. Although light delivery to each individual ion in a system is essential for general quantum manipulations and readout, experiments so far have employed optical systems that are cumbersome to scale to even a few tens of qubits. Here we demonstrate lithographically defined nanophotonic waveguide devices for light routing and ion addressing that are fully integrated within a surface-electrode ion trap chip. Ion qubits are addressed at multiple locations via focusing grating couplers emitting through openings in the trap electrodes to ions trapped 50 μm above the chip; using this light, we perform quantum coherent operations on the optical qubit transition in individual 88Sr+ ions. The grating focuses the beam to a diffraction-limited spot near the ion position with 2 μm 1/e2 radius along the trap axis, and we measure crosstalk errors between 10-2 and 4 × 10-4 at distances 7.5-15 μm from the beam centre. Owing to the scalability of the planar fabrication technique employed, together with the tight focusing and stable alignment afforded by the integration of the optics within the trap chip, this approach presents a path to creating the optical systems required for large-scale trapped-ion quantum information processing.

  20. Analysis of Hybrid-Integrated High-Speed Electro-Absorption Modulated Lasers Based on EM/Circuit Co-simulation

    DEFF Research Database (Denmark)

    Johansen, Tom Keinicke; Krozer, Viktor; Kazmierski, C.

    2009-01-01

    An improved electromagnetic simulation (EM) based approach has been developed for optimization of the electrical to optical (E/O) transmission properties of integrated electro-absorption modulated lasers (EMLs) aiming at 100 Gbit/s Ethernet applications. Our approach allows for an accurate analys...... of the EML performance in a hybrid microstrip assembly. The established EM-based approach provides a design methodology for the future hybrid integration of the EML with its driving electronics....

  1. Integral window hermetic fiber optic components

    Energy Technology Data Exchange (ETDEWEB)

    Dalton, R.D.; Kramer, D.P.; Massey, R.T.; Waker, D.A.

    1994-12-31

    In the fabrication of igniters, actuators, detonators, and other pyrotechnic devices to be activated by a laser beam, an integral optical glass window is formed by placing a preform in the structural member of the device and then melting the glass and sealing it in place by heating at a temperature between the ceramming temperature of the glass and the melting point of the metal, followed by rapid furnace cooling to avoid devitrification. No other sealing material is needed to achieve hermeticity. A preferred embodiment of this type of device is fabricated by allowing the molten glass to flow further and form a plano-convex lens integral with and at the bottom of the window. The lens functions to decrease the beam divergence caused by refraction of the laser light passing through the window when the device is fired by means of a laser beam.

  2. The GRAVITY integrated optics beam combination

    Science.gov (United States)

    Jocou, L.; Perraut, K.; Nolot, A.; Berger, J. P.; Moulin, T.; Labeye, P.; Lacour, S.; Perrin, G.; Lebouquin, J. B.; Bartko, H.; Thiel, M.; Eisenhauer, F.

    2010-07-01

    Gravity is a 2nd generation interferometric instrument for VLTI. It will combine 4 telescopes in dual feed in the K band to study general relativity effects around the Galactic Center black hole. The concept of Gravity is based on two equivalent beam combiner instruments: the scientific one fed by the science target (Sgr A*) and the fringe tracker fed by a bright reference star (See Gillessen et al.1). Both beam combination instruments are based on silica on silicon integrated optics (IO) component glued to fluoride glass fiber array. The beam combiners are implemented in a cryogenic vessel cooled at 200°K and back-illuminated by a high power laser used for metrology (Bartko et al.2). This paper is dedicated to the description of the development of the integrated beam combiner assembly.

  3. Integrated ion sensor device applications based on printed hybrid material systems (Conference Presentation)

    Science.gov (United States)

    List-Kratochvil, Emil J. W.

    2016-09-01

    Comfortable, wearable sensors and computers will enhance every person's awareness of his or her health condition, environment, chemical pollutants, potential hazards, and information of interest. In agriculture and in the food industry there is a need for a constant control of the condition and needs of plants, animals, and farm products. Yet many of these applications depend upon the development of novel, cheap devices and sensors that are easy to implement and to integrate. Organic semiconductors as well as several inorganic materials and hybrid material systems have proven to combine a number of intriguing optical and electronic properties with simple processing methods. As it will be reviewed in this contribution, these materials are believed to find their application in printed electronic devices allowing for the development of smart disposable devices in food-, health-, and environmental monitoring, diagnostics and control, possibly integrated into arrays of sensor elements for multi-parameter detection. In this contribution we review past and recent achievements in the field. Followed by a brief introduction, we will focus on two topics being on the agenda recently: a) the use of electrolyte-gated organic field-effect transistor (EGOFET) and ion-selective membrane based sensors for in-situ sensing of ions and biological substances and b) the development of hybrid material based resistive switches and their integration into fully functional, printed hybrid crossbar sensor array structures.

  4. Hybrid optical CDMA-FSO communications network under spatially correlated gamma-gamma scintillation

    DEFF Research Database (Denmark)

    Jurado-Navas, Antonio; Raddo, Thiago R.; Garrido-Balsells, José María

    2016-01-01

    In this paper, we propose a new hybrid network solution based on asynchronous optical code-division multiple-access (OCDMA) and free-space optical (FSO) technologies for last-mile access networks, where fiber deployment is impractical. The architecture of the proposed hybrid OCDMA-FSO network is ...

  5. Oxide-Free Bonding of III-V-Based Material on Silicon and Nano-Structuration of the Hybrid Waveguide for Advanced Optical Functions

    Directory of Open Access Journals (Sweden)

    Konstantinos Pantzas

    2015-10-01

    Full Text Available Oxide-free bonding of III-V-based materials for integrated optics is demonstrated on both planar Silicon (Si surfaces and nanostructured ones, using Silicon on Isolator (SOI or Si substrates. The hybrid interface is characterized electrically and mechanically. A hybrid InP-on-SOI waveguide, including a bi-periodic nano structuration of the silicon guiding layer is demonstrated to provide wavelength selective transmission. Such an oxide-free interface associated with the nanostructured design of the guiding geometry has great potential for both electrical and optical operation of improved hybrid devices.

  6. Porous silicon-VO{sub 2} based hybrids as possible optical temperature sensor: Wavelength-dependent optical switching from visible to near-infrared range

    Energy Technology Data Exchange (ETDEWEB)

    Antunez, E. E.; Salazar-Kuri, U.; Estevez, J. O.; Basurto, M. A.; Agarwal, V., E-mail: vagarwal@uaem.mx [Centro de Investigación en Ingeniería y Ciencias Aplicadas, Instituto de Investigación en Ciencias Básicas y Aplicadas, UAEM, Av. Universidad 1001, Col. Chamilpa, Cuernavaca, Mor. 62209 (Mexico); Campos, J. [Instituto de Energías Renovables, UNAM, Priv. Xochicalco S/N, Temixco, Mor. 62580 (Mexico); Jiménez Sandoval, S. [Laboratorio de Investigación en Materiales, Centro de Investigación y estudios Avanzados del Instituto Politécnico Nacional, Unidad Querétaro, Qro. 76001 (Mexico)

    2015-10-07

    Morphological properties of thermochromic VO{sub 2}—porous silicon based hybrids reveal the growth of well-crystalized nanometer-scale features of VO{sub 2} as compared with typical submicron granular structure obtained in thin films deposited on flat substrates. Structural characterization performed as a function of temperature via grazing incidence X-ray diffraction and micro-Raman demonstrate reversible semiconductor-metal transition of the hybrid, changing from a low-temperature monoclinic VO{sub 2}(M) to a high-temperature tetragonal rutile VO{sub 2}(R) crystalline structure, coupled with a decrease in phase transition temperature. Effective optical response studied in terms of red/blue shift of the reflectance spectra results in a wavelength-dependent optical switching with temperature. As compared to VO{sub 2} film over crystalline silicon substrate, the hybrid structure is found to demonstrate up to 3-fold increase in the change of reflectivity with temperature, an enlarged hysteresis loop and a wider operational window for its potential application as an optical temperature sensor. Such silicon based hybrids represent an exciting class of functional materials to display thermally triggered optical switching culminated by the characteristics of each of the constituent blocks as well as device compatibility with standard integrated circuit technology.

  7. Integrated optical addressing of an ion qubit

    CERN Document Server

    Mehta, Karan K; McConnell, Robert; Ram, Rajeev J; Sage, Jeremy M; Chiaverini, John

    2015-01-01

    Scalable implementation of the optics required to control trapped atomic ions' quantum states will be required to construct large-scale ion trap quantum information processors. All experiments in ion traps so far have employed approaches cumbersome to scale to even a few tens of qubits, with the majority relying on manipulation of free space beams with bulk optics. Here we demonstrate lithographically defined nanophotonic dielectric waveguides integrated within a linear surface-electrode ion trap chip, and qubit addressing at multiple locations via focusing grating couplers that emit through openings in the trap electrodes to an ion trapped 50 $\\mu$m above the chip. We perform quantum coherent operations using visible light routed in and emitted from silicon nitride waveguides and couplers, on the optical qubit transition in individual $^{88}$Sr$^+$ ions. The addressing beam is focused near the ion position with a 2 $\\mu$m 1/$e^2$-radius along the trap axis, and we measure crosstalk errors between $10^{-2}$ a...

  8. Fast integral methods for integrated optical systems simulations: a review

    Science.gov (United States)

    Kleemann, Bernd H.

    2015-09-01

    Boundary integral equation methods (BIM) or simply integral methods (IM) in the context of optical design and simulation are rigorous electromagnetic methods solving Helmholtz or Maxwell equations on the boundary (surface or interface of the structures between two materials) for scattering or/and diffraction purposes. This work is mainly restricted to integral methods for diffracting structures such as gratings, kinoforms, diffractive optical elements (DOEs), micro Fresnel lenses, computer generated holograms (CGHs), holographic or digital phase holograms, periodic lithographic structures, and the like. In most cases all of the mentioned structures have dimensions of thousands of wavelengths in diameter. Therefore, the basic methods necessary for the numerical treatment are locally applied electromagnetic grating diffraction algorithms. Interestingly, integral methods belong to the first electromagnetic methods investigated for grating diffraction. The development started in the mid 1960ies for gratings with infinite conductivity and it was mainly due to the good convergence of the integral methods especially for TM polarization. The first integral equation methods (IEM) for finite conductivity were the methods by D. Maystre at Fresnel Institute in Marseille: in 1972/74 for dielectric, and metallic gratings, and later for multiprofile, and other types of gratings and for photonic crystals. Other methods such as differential and modal methods suffered from unstable behaviour and slow convergence compared to BIMs for metallic gratings in TM polarization from the beginning to the mid 1990ies. The first BIM for gratings using a parametrization of the profile was developed at Karl-Weierstrass Institute in Berlin under a contract with Carl Zeiss Jena works in 1984-1986 by A. Pomp, J. Creutziger, and the author. Due to the parametrization, this method was able to deal with any kind of surface grating from the beginning: whether profiles with edges, overhanging non

  9. Universal quantum computation using all-optical hybrid encoding

    Institute of Scientific and Technical Information of China (English)

    郭奇; 程留永; 王洪福; 张寿

    2015-01-01

    By employing displacement operations, single-photon subtractions, and weak cross-Kerr nonlinearity, we propose an alternative way of implementing several universal quantum logical gates for all-optical hybrid qubits encoded in both single-photon polarization state and coherent state. Since these schemes can be straightforwardly implemented only using local operations without teleportation procedure, therefore, less physical resources and simpler operations are required than the existing schemes. With the help of displacement operations, a large phase shift of the coherent state can be obtained via currently available tiny cross-Kerr nonlinearity. Thus, all of these schemes are nearly deterministic and feasible under current technology conditions, which makes them suitable for large-scale quantum computing.

  10. Evaluation of systems and components for hybrid optical firing sets

    Energy Technology Data Exchange (ETDEWEB)

    Landry, M.J.; Rupert, J.W.; Mittas, A.

    1989-06-01

    High-energy density light appears to be a unique energy form that may be used to enhance the nuclear safety of weapon systems. Hybrid optical firing sets (HOFS) utilize the weak-link/strong-link exclusion region concept for nuclear safety; this method is similar to present systems, but uses light to transmit power across the exclusion region barrier. This report describes the assembling, operating, and testing of fourteen HOFS. These firing sets were required to charge a capacitor-discharge unit to 2.0 and 2.5 kV (100 mJ) in less than 1 s. First, we describe the components, the measurement techniques used to evaluate the components, and the different characteristics of the measured components. Second, we describe the HOFS studied, the setups used for evaluating them, and the resulting characteristics. Third, we make recommendations for improving the overall performance and suggest the best HOFS for packaging. 36 refs., 145 figs., 14 tabs.

  11. Hybrid formulation of radiation transport in optically thick divertor plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Rosato, J.; Marandet, Y.; Bufferand, H.; Stamm, R. [PIIM, UMR 7345 Aix-Marseille Universite / CNRS, Centre de St-Jerome, Marseille (France); Reiter, D. [IEK-4 Plasmaphysik, Forschungszentrum Juelich GmbH, Juelich (Germany)

    2016-08-15

    Kinetic Monte Carlo simulations of coupled atom-radiation transport in optically thick divertor plasmas can be computationally very demanding, in particular in ITER relevant conditions or even larger devices, e.g. for power plant divertor studies. At high (∝ 10{sup 15} cm{sup -3}) atomic densities, it can be shown that sufficiently large divertors behave in certain areas like a black body near the first resonance line of hydrogen (Lyman α). This suggests that, at least in part, the use of continuum model (radiation hydrodynamics) can be sufficiently accurate, while being less time consuming. In this work, we report on the development of a hybrid model devoted to switch automatically between a kinetic and a continuum description according to the plasma conditions. Calculations of the photo-excitation rate in a homogeneous slab are performed as an illustration. The outlined hybrid concept might be also applicable to neutral atom transport, due to mathematical analogy of transport equations for neutrals and radiation. (copyright 2016 The Authors. Contributions to Plasma Physics published by Wiley-VCH Verlag GmbH and Co. KGaA Weinheim. This)

  12. Integrated optics for astronomical interferometry; 1, Concept and astronomical applications

    CERN Document Server

    Malbet, M; Schanen-Duport, J P; Berger, J P; Rousselet-Perraut, K; Benech, P

    1999-01-01

    We propose a new instrumental concept for long-baseline optical single-mode interferometry using integrated optics which were developed for telecommunication. Visible and infrared multi-aperture interferometry requires many optical functions (spatial filtering, beam combination, photometric calibration, polarization control) to detect astronomical signals at very high angular resolution. Since the 80's, integrated optics on planar substrate have become available for telecommunication applications with multiple optical functions like power dividing, coupling, multiplexing, etc. We present the concept of an optical / infrared interferometric instrument based on this new technology. The main advantage is to provide an interferometric combination unit on a single optical chip. Integrated optics are compact, provide stability, low sensitivity to external constrains like temperature, pressure or mechanical stresses, no optical alignment except for coupling, simplicity and intrinsic polarization control. The integra...

  13. Hybrid integrated PDMS microfluidics with a silica capillary.

    Science.gov (United States)

    Dimov, Ivan K; Riaz, Asif; Ducrée, Jens; Lee, Luke P

    2010-06-07

    To harness the properties of both PDMS and silica, we have demonstrated hybrid integrated PDMS microfluidic systems with fused silica capillaries. The hybrid integrated PDMS microfluidics and silica capillary (iPSC) modules exhibit a novel architecture and method for leakage free CE sample injection merely requiring a single high voltage source and one pair of electrodes. The use of the iPSC device is based on a modular approach which allows the capillary to be reused extensively whilst replacing the attached fluidic module for different experiments. Integrating fused silica capillaries with PDMS microfluidic modules allows the direct application of a wide variety of well established conventional CE protocols for separations of complex analytes. Furthermore it bears the potential for facile coupling to standard electro-spray ionization mass spectrometry (ESI-MS), letting users focus on the sample analysis rather than the development of new separation protocols. The fabrication of the iPSC module consists of a simple and quick three-step method that submerges a fused silica capillary in PDMS prepolymer. After cross linking the prepolymer and punching the inlets, the iPSC module layer can be mounted onto a microfluidic device for CE separation.

  14. Parametric study of dielectric loaded surface plasmon polariton add-drop filters for hybrid silicon/plasmonic optical circuitry

    Science.gov (United States)

    Dereux, A.; Hassan, K.; Weeber, J.-C.; Djellali, N.; Bozhevolnyi, S. I.; Tsilipakos, O.; Pitilakis, A.; Kriezis, E.; Papaioannou, S.; Vyrsokinos, K.; Pleros, N.; Tekin, T.; Baus, M.; Kalavrouziotis, D.; Giannoulis, G.; Avramopoulos, H.

    2011-01-01

    Surface plasmons polaritons are electromagnetic waves propagating along the surface of a conductor. Surface plasmons photonics is a promising candidate to satisfy the constraints of miniaturization of optical interconnects. This contribution reviews an experimental parametric study of dielectric loaded surface plasmon waveguides ring resonators and add-drop filters within the perspective of the recently suggested hybrid technology merging plasmonic and silicon photonics on a single board (European FP7 project PLATON "Merging Plasmonic and Silicon Photonics Technology towards Tb/s routing in optical interconnects"). Conclusions relevant for dielectric loaded surface plasmon switches to be integrated in silicon photonic circuitry will be drawn. They rely on the opportunity offered by plasmonic circuitry to carry optical signals and electric currents through the same thin metal circuitry. The heating of the dielectric loading by the electric current enables to design low foot-print thermo-optical switches driving the optical signal flow.

  15. Integral relations of optical characteristics involving pairs of condensed medium

    Science.gov (United States)

    Sakhnovskyj, Mykhajlo Y.; Tymochko, Bogdan M.; Rudeichuk, Volodymyr M.; Dominikov, Mickolay M.

    2015-11-01

    The integral relations among optical invariants and elipsometric parameters of light are obtained in this paper. It is shown, that among optical invariants there is an integral relation, similar to Kramers-Kronig relation for complex dielectric conductivity or a complex index of refraction. The possibility to determine the spectral values of conductivity through the integral transform of optical invariants or ellipsometric angles is discussed.

  16. Optimisation and Integration of Hybrid Renewable Energy Storage Systems

    Science.gov (United States)

    Eriksson, E. L. V.; MacA Gray, E.

    2017-07-01

    This paper discusses renewable energy system concepts and integration techniques, and reviews modelling and optimization techniques for hybrid renewable energy systems for electricity provision. A proposal to use design criteria that are not limited to performance- and cost-related factors is introduced and forms a background to the following discussion. Optimization techniques in relation to constraints, reliability analysis and algorithms are discussed as well as software tools available for modelling/simulation, component sizing and optimization. The focus is on systems incorporating hydrogen, but the ideas presented have general relevance.

  17. Highly integrated optical phased arrays: photonic integrated circuits for optical beam shaping and beam steering

    Directory of Open Access Journals (Sweden)

    Heck Martijn J.R.

    2017-01-01

    Full Text Available Technologies for efficient generation and fast scanning of narrow free-space laser beams find major applications in three-dimensional (3D imaging and mapping, like Lidar for remote sensing and navigation, and secure free-space optical communications. The ultimate goal for such a system is to reduce its size, weight, and power consumption, so that it can be mounted on, e.g. drones and autonomous cars. Moreover, beam scanning should ideally be done at video frame rates, something that is beyond the capabilities of current opto-mechanical systems. Photonic integrated circuit (PIC technology holds the promise of achieving low-cost, compact, robust and energy-efficient complex optical systems. PICs integrate, for example, lasers, modulators, detectors, and filters on a single piece of semiconductor, typically silicon or indium phosphide, much like electronic integrated circuits. This technology is maturing fast, driven by high-bandwidth communications applications, and mature fabrication facilities. State-of-the-art commercial PICs integrate hundreds of elements, and the integration of thousands of elements has been shown in the laboratory. Over the last few years, there has been a considerable research effort to integrate beam steering systems on a PIC, and various beam steering demonstrators based on optical phased arrays have been realized. Arrays of up to thousands of coherent emitters, including their phase and amplitude control, have been integrated, and various applications have been explored. In this review paper, I will present an overview of the state of the art of this technology and its opportunities, illustrated by recent breakthroughs.

  18. Highly integrated optical phased arrays: photonic integrated circuits for optical beam shaping and beam steering

    Science.gov (United States)

    Heck, Martijn J. R.

    2017-01-01

    Technologies for efficient generation and fast scanning of narrow free-space laser beams find major applications in three-dimensional (3D) imaging and mapping, like Lidar for remote sensing and navigation, and secure free-space optical communications. The ultimate goal for such a system is to reduce its size, weight, and power consumption, so that it can be mounted on, e.g. drones and autonomous cars. Moreover, beam scanning should ideally be done at video frame rates, something that is beyond the capabilities of current opto-mechanical systems. Photonic integrated circuit (PIC) technology holds the promise of achieving low-cost, compact, robust and energy-efficient complex optical systems. PICs integrate, for example, lasers, modulators, detectors, and filters on a single piece of semiconductor, typically silicon or indium phosphide, much like electronic integrated circuits. This technology is maturing fast, driven by high-bandwidth communications applications, and mature fabrication facilities. State-of-the-art commercial PICs integrate hundreds of elements, and the integration of thousands of elements has been shown in the laboratory. Over the last few years, there has been a considerable research effort to integrate beam steering systems on a PIC, and various beam steering demonstrators based on optical phased arrays have been realized. Arrays of up to thousands of coherent emitters, including their phase and amplitude control, have been integrated, and various applications have been explored. In this review paper, I will present an overview of the state of the art of this technology and its opportunities, illustrated by recent breakthroughs.

  19. Stripline kicker for integrable optics test accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Antipov, Sergey A.; Didenko, Alexander; Lebedev, Valeri; Valishev, Alexander

    2016-06-30

    We present a design of a stripline kicker for Integrable Optics Test Accelerator (IOTA). For its experimental program IOTA needs two full-aperture kickers, capable to create an arbitrary controllable kick in 2D. For that reason their strengths are variable in a wide range of amplitudes up to 16 mrad, and the pulse length 100 ns is less than a revolution period for electrons. In addition, the kicker should have a physical aperture of 40 mm for a proposed operation with proton beam, and an outer size of 70 mm to fit inside existing quadrupole magnets to save space in the ring. Computer simulations using CST Microwave Studio show high field uniformity and wave impedance close to 50 {\\Omega}.

  20. Stripline kicker for integrable optics test accelerator

    CERN Document Server

    Antipov, Sergey A; Lebedev, Valeri; Valishev, Alexander

    2016-01-01

    We present a design of a stripline kicker for Integrable Optics Test Accelerator (IOTA). For its experimental program IOTA needs two full-aperture kickers, capable to create an arbitrary controllable kick in 2D. For that reason their strengths are variable in a wide range of amplitudes up to 16 mrad, and the pulse length 100 ns is less than a revolution period for electrons. In addition, the kicker should have a physical aperture of 40 mm for a proposed operation with proton beam, and an outer size of 70 mm to fit inside existing quadrupole magnets to save space in the ring. Computer simulations using CST Microwave Studio show high field uniformity and wave impedance close to 50 {\\Omega}.

  1. Towards the development of a hybrid-integrated chip interferometer for online surface profile measurements.

    Science.gov (United States)

    Kumar, P; Martin, H; Jiang, X

    2016-06-01

    Non-destructive testing and online measurement of surface features are pressing demands in manufacturing. Thus optical techniques are gaining importance for characterization of complex engineering surfaces. Harnessing integrated optics for miniaturization of interferometry systems onto a silicon wafer and incorporating a compact optical probe would enable the development of a handheld sensor for embedded metrology applications. In this work, we present the progress in the development of a hybrid photonics based metrology sensor device for online surface profile measurements. The measurement principle along with test and measurement results of individual components has been presented. For non-contact measurement, a spectrally encoded lateral scanning probe based on the laser scanning microscopy has been developed to provide fast measurement with lateral resolution limited to the diffraction limit. The probe demonstrates a lateral resolution of ∼3.6 μm while high axial resolution (sub-nanometre) is inherently achieved by interferometry. Further the performance of the hybrid tuneable laser and the scanning probe was evaluated by measuring a standard step height sample of 100 nm.

  2. High Voltage Dielectrophoretic and Magnetophoretic Hybrid Integrated Circuit / Microfluidic Chip

    Science.gov (United States)

    Issadore, David; Franke, Thomas; Brown, Keith A.; Hunt, Thomas P.; Westervelt, Robert M.

    2010-01-01

    A hybrid integrated circuit (IC) / microfluidic chip is presented that independently and simultaneously traps and moves microscopic objects suspended in fluid using both electric and magnetic fields. This hybrid chip controls the location of dielectric objects, such as living cells and drops of fluid, on a 60 × 61 array of pixels that are 30 × 38 μm2 in size, each of which can be individually addressed with a 50 V peak-to-peak, DC to 10 MHz radio frequency voltage. These high voltage pixels produce electric fields above the chip’s surface with a magnitude , resulting in strong dielectrophoresis (DEP) forces . Underneath the array of DEP pixels there is a magnetic matrix that consists of two perpendicular sets of 60 metal wires running across the chip. Each wire can be sourced with 120 mA to trap and move magnetically susceptible objects using magnetophoresis (MP). The DEP pixel array and magnetic matrix can be used simultaneously to apply forces to microscopic objects, such as living cells or lipid vesicles, that are tagged with magnetic nanoparticles. The capabilities of the hybrid IC / microfluidic chip demonstrated in this paper provide important building blocks for a platform for biological and chemical applications. PMID:20625468

  3. Runoff prediction using an integrated hybrid modelling scheme

    Science.gov (United States)

    Remesan, Renji; Shamim, Muhammad Ali; Han, Dawei; Mathew, Jimson

    2009-06-01

    SummaryRainfall runoff is a very complicated process due to its nonlinear and multidimensional dynamics, and hence difficult to model. There are several options for a modeller to consider, for example: the type of input data to be used, the length of model calibration (training) data and whether or not the input data be treated as signals with different frequency bands so that they can be modelled separately. This paper describes a new hybrid modelling scheme to answer the above mentioned questions. The proposed methodology is based on a hybrid model integrating wavelet transformation, a modelling engine (Artificial Neural Network) and the Gamma Test. First, the Gamma Test is used to decide the required input data dimensions and its length. Second, the wavelet transformation decomposes the input signals into different frequency bands. Finally, a modelling engine (ANN in this study) is used to model the decomposed signals separately. The proposed scheme was tested using the Brue catchment, Southwest England, as a case study and has produced very positive results. The hybrid model outperforms all other models tested. This study has a wider implication in the hydrological modelling field since its general framework could be applied to other model combinations (e.g., model engine could be Support Vector Machines, neuro-fuzzy systems, or even a conceptual model. The signal decomposition could be carried out by Fourier transformation).

  4. Hybrid Solar: A Review on Photovoltaic and Thermal Power Integration

    Directory of Open Access Journals (Sweden)

    T. T. Chow

    2012-01-01

    Full Text Available The market of solar thermal and photovoltaic electricity generation is growing rapidly. New ideas on hybrid solar technology evolve for a wide range of applications, such as in buildings, processing plants, and agriculture. In the building sector in particular, the limited building space for the accommodation of solar devices has driven a demand on the use of hybrid solar technology for the multigeneration of active power and/or passive solar devices. The importance is escalating with the worldwide trend on the development of low-carbon/zero-energy buildings. Hybrid photovoltaic/thermal (PVT collector systems had been studied theoretically, numerically, and experimentally in depth in the past decades. Together with alternative means, a range of innovative products and systems has been put forward. The final success of the integrative technologies relies on the coexistence of robust product design/construction and reliable system operation/maintenance in the long run to satisfy the user needs. This paper gives a broad review on the published academic works, with an emphasis placed on the research and development activities in the last decade.

  5. Directed assembly of hybrid nanostructures using optically resonant nanotweezers

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, David [Cornell Univ., Ithaca, NY (United States)

    2015-09-09

    This represents the final report for this project. Over the course of the project we have made significant progress in photonically driven nano-assembly including: (1) demonstrating the first direct optical tweezer based manipulation of proteins, (2) the ability to apply optical angular torques to microtubuals and other rod-shaped microparticles, (3) direct assembly of hybrid nanostructures comprising of polymeric nanoparticles and carbon nanotubes and, (4) the ability to drive biological reactions (specifically protein aggregation) that are thermodynamically unfavorable by applying localized optical work. These advancements are described in the list of papers provided in section 2.0 of the below. Summary details are provided in prior year annual reports. We have two additional papers which will be submitted shortly based on the work done under this award. An updated publication list will be provided to the program manager when those are accepted. In this report, we report on a new advancement made in the final project year, which uses the nanotweezer technology to perform direct measurements of particle-surface interactions. Briefly, these measurements are important for characterizing the stability and behavior of colloidal and nanoparticle suspensions and current techniques are limited in their ability to measure piconewton scale interaction forces on sub-micrometer particles due to signal detection limits and thermal noise. In this project year we developed a new technique called “Nanophotonic Force Microscopy” which uses the localized region of exponentially decaying, near-field, light to confine small particles close to a surface. From the statistical distribution of the light intensity scattered by the particle the technique maps out the potential well of the trap and directly quantify the repulsive force between the nanoparticle and the surface. The major advantage of the technique is that it can measure forces and energy wells below the thermal noise

  6. Ka-Band Link Study and Analysis for a Mars Hybrid RF/Optical Software Defined Radio

    Science.gov (United States)

    Zeleznikar, Daniel J.; Nappier, Jennifer M.; Downey, Joseph A.

    2014-01-01

    The integrated radio and optical communications (iROC) project at the NASA Glenn Research Center (GRC) is investigating the feasibility of a hybrid RF and optical communication subsystem for future deep space missions. The hybrid communications subsystem enables the advancement of optical communications while simultaneously mitigating the risk of infusion by combining an experimental optical transmitter and telescope with a reliable Ka-band RF transmitter and antenna. The iROC communications subsystem seeks to maximize the total data return over the course of a potential 2-year mission in Mars orbit beginning in 2021. Although optical communication by itself offers potential for greater data return over RF, the reliable Ka-band link is also being designed for high data return capability in this hybrid system. A daily analysis of the RF link budget over the 2-year span is performed to optimize and provide detailed estimates of the RF data return. In particular, the bandwidth dependence of these data return estimates is analyzed for candidate waveforms. In this effort, a data return modeling tool was created to analyze candidate RF modulation and coding schemes with respect to their spectral efficiency, amplifier output power back-off, required digital to analog conversion (DAC) sampling rates, and support by ground receivers. A set of RF waveforms is recommended for use on the iROC platform.

  7. Optical tuning of near and far fields form hybrid dimer nanoantennas via laser-induced melting

    Science.gov (United States)

    Kolodny, Stanislav A.; Sun, Yali; Zuev, Dmitry A.; Makarov, Sergey V.; Krasnok, Alexander E.; Belov, Pavel A.

    2016-08-01

    Hybrid nanophotonics based on metal-dielectric nanostructures unifies the advantages of plasmonics and all-dielectric nanophotonics providing strong localization of light, magnetic optical response and specifically designed scattering properties. Here, we propose a new method for optical properties tuning of hybrid dimer nanoantenas via laser-induced melting at the nanoscale. We demonstrate numerically that near- and farfield properties of a hybrid nanoantenna dramatically changes with fs-laser modification of Au particle. The results lay the groundwork for the fine-tuning of hybrid nanoantennas and can be applied for effective light manipulation at the nanoscale, as well as biomedical and energy applications.

  8. Integrated optical investigation of two light-sensitive proteins

    Science.gov (United States)

    Fábián, László; Krekic, Szilvia; Tóth-Boconádi, Rudolf; Taneva, Stefka G.; Bálint, Agneta M.; Nánai, László; Dér, András

    2017-01-01

    Integrated optics is one of the most intensively investigated fields when working on alternative methods to overcome the disadvantages of integrated electronics. Besides inorganic active optical crystals, dyes and polymers, molecules of biological origin with suitable nonlinear optical properties can also find applications in integrated optical - biophotonic - devices. The state-of-the-art photonic integration technology is ready to provide the passive elements of integrated optical circuits. The bottle-neck in integrated optics is to find a proper nonlinear optical material that is supposed to be the cladding medium in waveguide-based photonic applications, performing light-controlled active functions. Based on our earlier results, here we present the experimental demonstration of subpicosecond photonic switching with an alternative approach, where the active role is performed by a biological material, the chromoprotein bacteriorhodopsin. Moreover, measurements of the light-induced refractive index change performed on a dried film of the Photoactive Yellow Protein are also presented. Our findings show that these photochromic pigments can be promising candidates as active nonlinear optical materials for all-optical data processing in future biophotonic applications. These results may serve as a basis for the future realization of protein-based integrated optical devices that can eventually lead to a conceptual revolution in the development of telecommunication technologies.

  9. Multi-carrier transmission for hybrid radio frequency with optical wireless communications

    Science.gov (United States)

    Wang, Gang; Chen, Genshe; Shen, Dan; Pham, Khanh; Blasch, Erik; Nguyen, Tien M.

    2015-05-01

    Radio frequency (RF) wireless communication is reaching its capacity to support large data rate transmissions due to hardware constraints (e.g., silicon processes), software strategies (e.g., information theory), and consumer desire for timely large file exchanges (e.g., big data and mobile cloud computing). A high transmission rate performance must keep pace with the generated huge volumes of data for real-time processing. Integrated RF and optical wireless communications (RF/OWC) could be the next generation transmission technology to satisfy both the increased data rate exchange and the communications constraints. However, with the promising benefits of RF/OWC, challenges remain to fully develop hybrid RF with wireless optical communications such as uniform waveform design for information transmission and detection. In this paper, an orthogonal frequency division multiplexing (OFDM) transmission scheme, which widely employed in RF communications, is developed for optical communications. The traditional high peak-to-average power ratio (PAPR) in OFDM is reduced to improve system performance. The proposed multi-carrier waveform is evaluated with a frequency-selective fading channel. The results demonstrate that bit error rate (BER) performance of our proposed optical OFDM transmission technique outperforms the traditional OWC on-off keying (OOK) transmission scheme.

  10. Integrated hybrid silicon DFB laser-EAM array using quantum well intermixing.

    Science.gov (United States)

    Jain, Siddharth R; Sysak, Matthew N; Kurczveil, Geza; Bowers, John E

    2011-07-04

    We demonstrate multiple bandgap integration on the hybrid silicon platform using quantum well intermixing. A broadband DFB laser array and a DFB-EAM array are realized on a single chip using four bandgaps defined by ion implantation enhanced disordering. The broadband laser array uses two bandgaps with 17 nm blue shift to compensate for gain roll-off while the integrated DFB-EAMs use the as-grown bandgap for optical gain and a 30 nm blue shifted bandgap for modulation. The multi-channel DFB array includes 13 lasers with >90 nm gain-bandwidth. The transponder includes four DFB-EAMs with 14 dB DC extinction at 4 V bias.

  11. High resolution hybrid optical and acoustic sea floor maps (Invited)

    Science.gov (United States)

    Roman, C.; Inglis, G.

    2013-12-01

    This abstract presents a method for creating hybrid optical and acoustic sea floor reconstructions at centimeter scale grid resolutions with robotic vehicles. Multibeam sonar and stereo vision are two common sensing modalities with complementary strengths that are well suited for data fusion. We have recently developed an automated two stage pipeline to create such maps. The steps can be broken down as navigation refinement and map construction. During navigation refinement a graph-based optimization algorithm is used to align 3D point clouds created with both the multibeam sonar and stereo cameras. The process combats the typical growth in navigation error that has a detrimental affect on map fidelity and typically introduces artifacts at small grid sizes. During this process we are able to automatically register local point clouds created by each sensor to themselves and to each other where they overlap in a survey pattern. The process also estimates the sensor offsets, such as heading, pitch and roll, that describe how each sensor is mounted to the vehicle. The end results of the navigation step is a refined vehicle trajectory that ensures the points clouds from each sensor are consistently aligned, and the individual sensor offsets. In the mapping step, grid cells in the map are selectively populated by choosing data points from each sensor in an automated manner. The selection process is designed to pick points that preserve the best characteristics of each sensor and honor some specific map quality criteria to reduce outliers and ghosting. In general, the algorithm selects dense 3D stereo points in areas of high texture and point density. In areas where the stereo vision is poor, such as in a scene with low contrast or texture, multibeam sonar points are inserted in the map. This process is automated and results in a hybrid map populated with data from both sensors. Additional cross modality checks are made to reject outliers in a robust manner. The final

  12. (Bio)hybrid materials based on optically active particles

    Science.gov (United States)

    Reitzig, Manuela; Härtling, Thomas; Opitz, Jörg

    2014-03-01

    In this contribution we provide an overview of current investigations on optically active particles (nanodiamonds, upconversion phospors) for biohybrid and sensing applications. Due to their outstanding properties nanodiamonds gain attention in various application elds such as microelectronics, optical monitoring, medicine, and biotechnology. Beyond the typical diamond properties such as high thermal conductivity and extreme hardness, the carbon surface and its various functional groups enable diverse chemical and biological surface functionalization. At Fraunhofer IKTS-MD we develop a customization of material surfaces via integration of chemically modi ed nanodiamonds at variable surfaces, e.g bone implants and pipelines. For the rst purpose, nanodiamonds are covalently modi ed at their surface with amino or phosphate functionalities that are known to increase adhesion to bone or titanium alloys. The second type of surface is approached via mechanical implementation into coatings. Besides nanodiamonds, we also investigate the properties of upconversion phosphors. In our contribution we show how upconversion phosphors are used to verify sterilization processes via a change of optical properties due to sterilizing electron beam exposure.

  13. Relation between noise and resolution in integrated optical refractometric sensing

    NARCIS (Netherlands)

    Hoekstra, H.J.W.M.; Lambeck, P.V.; Uranus, H.P.; Koster, T.M.

    2008-01-01

    The paper presents a general theory for integrated optical (IO) sensing devices of the refractometric type, which relates noise and device parameters to the resolution of the measurand induced modal index changes. The theory is applied for length optimization of a number of integrated optical sensin

  14. Tunable integrated optical filter made of a glass ion-exchanged waveguide and an electro-optic composite holographic grating.

    Science.gov (United States)

    d'Alessandro, Antonio; Donisi, Domenico; De Sio, Luciano; Beccherelli, Romeo; Asquini, Rita; Caputo, Roberto; Umeton, Cesare

    2008-06-23

    We report the fabrication and the optical characterization of a hybrid tunable integrated optical filter. It consists of a diffused ion-exchanged channel waveguide on a borosilicate glass substrate with a cover of the same glass to form a gap filled with a holographic grating. The grating morphology, called POLICRYPS (POlymer LIquid CRYstal Polymer Slices), is made of alternating stripes of polymer and liquid crystal acting as overlayer for the underneath waveguide. The filter structure includes aluminum coplanar electrodes to electrically control the grating properties, allowing the tunability of the filter. The electric driving power required to tune the filter obtained was in the range of submilliwatts due to the efficient liquid crystal electro-optic effect.

  15. Model GC1312S Multifunction Integrated Optical Circuit Devices

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Model GC1312S multifunction integrated optical circuit device (MIOC) used in inertial-grade interferometric fiber optics gyroscopes (IFOGs) is fabricated by annealing and proton exchange process (APE). The unique feature of the device is the incorporation of the beat detection circuit besides all the features the conventional single Y-branch multifunction integrated optical circuit devices have. The device structure, operation principle and typical characteristics, etc., are briefly presented in this paper.

  16. Optical properties of hybrid semiconductor-metal structures

    Energy Technology Data Exchange (ETDEWEB)

    Kreilkamp, L.E.; Pohl, M.; Akimov, I.A.; Yakovlev, D.R.; Bayer, M. [Experimentelle Physik 2, Technische Universitaet Dortmund, 44221 Dortmund (Germany); Belotelov, V.I.; Zvezdin, A.K. [A.M. Prokhorov General Physics Institute, Russian Academy of Sciences, 119992 Moscow (Russian Federation); Karczewski, G.; Wojtowicz, T. [Institute of Physics, Polish Academy of Sciences, 02668 Warsaw (Poland); Rudzinski, A.; Kahl, M. [Raith GmbH, Konrad-Adenauer-Allee 8, 44263 Dortmund (Germany)

    2012-07-01

    We study the optical properties of hybrid nanostructures comprising a semiconductor CdTe quantum well (QW) separated by a thin CdMgTe cap layer of 40 nm from a patterned gold film. The CdTe/CdMgTe QW structure with a well width of 10nm was grown by molecular beam epitaxy. The one-dimensional periodic gold films on top were made using e-beam lithography and lift-off process. The investigated structures can be considered as plasmonic crystals because the metal films attached to the semiconductor are patterned with a period in the range from 475 to 600 nm, which is comparable to the surface plasmon-polariton (SPP) wavelength. Angle dependent reflection spectra at room temperature clearly show plasmonic resonances. PL spectra taken at low temperatures of about 10 K under below- and above-barrier illumination show significant modifications compared to the unstructured QW sample. The number of emission lines and their position shift change depending on the excitation energy. The role of exciton-SPP coupling and Schottky barrier at the semiconductor-metal interface are discussed.

  17. Surface plasmon-assisted optical bistability in the quantum dot-metal nanoparticle hybrid system

    Science.gov (United States)

    Bao, Chengjun; Qi, Yihong; Niu, Yueping; Gong, Shangqing

    2016-07-01

    We theoretically investigated optical bistability (OB) of a coupled excition-plasmon hybrid system in a unidirectional ring cavity. It is found that the threshold and the region of OB can be tuned by adjusting the center-center distance between the quantum dot and metal nanoparticle (MNP), the Rabi frequency of the control field and the radius of the MNP. Due to the significantly enhanced optical nonlinearity by the surface plasmon effect, the threshold of OB can be decreased greatly when the probe field is parallel to the major axis of the hybrid system. The enhanced OB may have promising applications in optical switching and optical storage.

  18. A novel optical beam splitter based on photonic crystal with hybrid lattices

    Institute of Scientific and Technical Information of China (English)

    Zhu Qing-Yi; Fu Yong-Qi; Hu De-Qing; Zhang Zhi-Min

    2012-01-01

    A novel optical beam splitter constructed on the basis of photonic crystal (PC) with hybrid lattices is proposed in this paper.The band gap of square-lattice PC is so designed that the incident light is divided into several branch beams.Triangular-lattice graded-index PCs are combined for focusing each branch.Computational calculations are carried out on the basis of finite-different time-domain algorithm to prove the feasibility of our design.The waveguide is unnecessary in the design.Thus the device has functions of both splitting and focusing beams.Size of the divided beam at site of full-width at half-maximum is of the order of λ/2.The designed splitter has the advantages that it has a small volume and can be integrated by conventional semiconductor manufacturing process.

  19. Modeling Integrated Cellular Machinery Using Hybrid Petri-Boolean Networks

    Science.gov (United States)

    Berestovsky, Natalie; Zhou, Wanding; Nagrath, Deepak; Nakhleh, Luay

    2013-01-01

    The behavior and phenotypic changes of cells are governed by a cellular circuitry that represents a set of biochemical reactions. Based on biological functions, this circuitry is divided into three types of networks, each encoding for a major biological process: signal transduction, transcription regulation, and metabolism. This division has generally enabled taming computational complexity dealing with the entire system, allowed for using modeling techniques that are specific to each of the components, and achieved separation of the different time scales at which reactions in each of the three networks occur. Nonetheless, with this division comes loss of information and power needed to elucidate certain cellular phenomena. Within the cell, these three types of networks work in tandem, and each produces signals and/or substances that are used by the others to process information and operate normally. Therefore, computational techniques for modeling integrated cellular machinery are needed. In this work, we propose an integrated hybrid model (IHM) that combines Petri nets and Boolean networks to model integrated cellular networks. Coupled with a stochastic simulation mechanism, the model simulates the dynamics of the integrated network, and can be perturbed to generate testable hypotheses. Our model is qualitative and is mostly built upon knowledge from the literature and requires fine-tuning of very few parameters. We validated our model on two systems: the transcriptional regulation of glucose metabolism in human cells, and cellular osmoregulation in S. cerevisiae. The model produced results that are in very good agreement with experimental data, and produces valid hypotheses. The abstract nature of our model and the ease of its construction makes it a very good candidate for modeling integrated networks from qualitative data. The results it produces can guide the practitioner to zoom into components and interconnections and investigate them using such more

  20. Modeling integrated cellular machinery using hybrid Petri-Boolean networks.

    Directory of Open Access Journals (Sweden)

    Natalie Berestovsky

    Full Text Available The behavior and phenotypic changes of cells are governed by a cellular circuitry that represents a set of biochemical reactions. Based on biological functions, this circuitry is divided into three types of networks, each encoding for a major biological process: signal transduction, transcription regulation, and metabolism. This division has generally enabled taming computational complexity dealing with the entire system, allowed for using modeling techniques that are specific to each of the components, and achieved separation of the different time scales at which reactions in each of the three networks occur. Nonetheless, with this division comes loss of information and power needed to elucidate certain cellular phenomena. Within the cell, these three types of networks work in tandem, and each produces signals and/or substances that are used by the others to process information and operate normally. Therefore, computational techniques for modeling integrated cellular machinery are needed. In this work, we propose an integrated hybrid model (IHM that combines Petri nets and Boolean networks to model integrated cellular networks. Coupled with a stochastic simulation mechanism, the model simulates the dynamics of the integrated network, and can be perturbed to generate testable hypotheses. Our model is qualitative and is mostly built upon knowledge from the literature and requires fine-tuning of very few parameters. We validated our model on two systems: the transcriptional regulation of glucose metabolism in human cells, and cellular osmoregulation in S. cerevisiae. The model produced results that are in very good agreement with experimental data, and produces valid hypotheses. The abstract nature of our model and the ease of its construction makes it a very good candidate for modeling integrated networks from qualitative data. The results it produces can guide the practitioner to zoom into components and interconnections and investigate them

  1. Modeling integrated cellular machinery using hybrid Petri-Boolean networks.

    Directory of Open Access Journals (Sweden)

    Natalie Berestovsky

    Full Text Available The behavior and phenotypic changes of cells are governed by a cellular circuitry that represents a set of biochemical reactions. Based on biological functions, this circuitry is divided into three types of networks, each encoding for a major biological process: signal transduction, transcription regulation, and metabolism. This division has generally enabled taming computational complexity dealing with the entire system, allowed for using modeling techniques that are specific to each of the components, and achieved separation of the different time scales at which reactions in each of the three networks occur. Nonetheless, with this division comes loss of information and power needed to elucidate certain cellular phenomena. Within the cell, these three types of networks work in tandem, and each produces signals and/or substances that are used by the others to process information and operate normally. Therefore, computational techniques for modeling integrated cellular machinery are needed. In this work, we propose an integrated hybrid model (IHM that combines Petri nets and Boolean networks to model integrated cellular networks. Coupled with a stochastic simulation mechanism, the model simulates the dynamics of the integrated network, and can be perturbed to generate testable hypotheses. Our model is qualitative and is mostly built upon knowledge from the literature and requires fine-tuning of very few parameters. We validated our model on two systems: the transcriptional regulation of glucose metabolism in human cells, and cellular osmoregulation in S. cerevisiae. The model produced results that are in very good agreement with experimental data, and produces valid hypotheses. The abstract nature of our model and the ease of its construction makes it a very good candidate for modeling integrated networks from qualitative data. The results it produces can guide the practitioner to zoom into components and interconnections and investigate them

  2. Hybrid Nonlinear Optical Materials for Applications in Power Limiting and Photorefractive Devices

    Science.gov (United States)

    2010-03-01

    Final 3. DATES COVERED (From - To) 04/01/2007 to 11/30/2009 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER FA9550-07-1-0307 Hybrid Nonlinear Optical Materials for...Hybrid  Nonlinear   Optical   Materials  for Applications in Power  Limiting and Photorefractive devices      Prime Contract: FA95500710307

  3. Superconducting single-photon detectors for integrated quantum optics

    Energy Technology Data Exchange (ETDEWEB)

    Kahl, Oliver

    2016-01-29

    This thesis reports on the implementation and characterization of a fully integrated single-photon detector. Several detector circuits are realized and it is shown that the detectors exhibit supreme detection performance over a wide optical spectrum. The detectors' scalability is showcased by the parallel operation of multiple detectors within a single integrated circuit. These demonstrations are essential for future developments in integrated quantum optics.

  4. Hybrid scheduling mechanisms for Next-generation Passive Optical Networks based on network coding

    Science.gov (United States)

    Zhao, Jijun; Bai, Wei; Liu, Xin; Feng, Nan; Maier, Martin

    2014-10-01

    Network coding (NC) integrated into Passive Optical Networks (PONs) is regarded as a promising solution to achieve higher throughput and energy efficiency. To efficiently support multimedia traffic under this new transmission mode, novel NC-based hybrid scheduling mechanisms for Next-generation PONs (NG-PONs) including energy management, time slot management, resource allocation, and Quality-of-Service (QoS) scheduling are proposed in this paper. First, we design an energy-saving scheme that is based on Bidirectional Centric Scheduling (BCS) to reduce the energy consumption of both the Optical Line Terminal (OLT) and Optical Network Units (ONUs). Next, we propose an intra-ONU scheduling and an inter-ONU scheduling scheme, which takes NC into account to support service differentiation and QoS assurance. The presented simulation results show that BCS achieves higher energy efficiency under low traffic loads, clearly outperforming the alternative NC-based Upstream Centric Scheduling (UCS) scheme. Furthermore, BCS is shown to provide better QoS assurance.

  5. Integration of microfluidics with a four-channel integrated optical Young interferometer immunosensor.

    Science.gov (United States)

    Ymeti, A; Kanger, J S; Greve, J; Besselink, G A J; Lambeck, P V; Wijn, R; Heideman, R G

    2005-01-15

    This report describes an optical sensing hybrid system obtained by bonding a microfluidic system to an integrated optical (IO) four-channel Young interferometer (YI) chip. The microfluidic system implemented into a glass plate consists of four microchannels with cross-sectional dimensions of 200 microm x 15 microm. The microfluidic system is structured in such a way that after bonding to the IO chip, each microchannel addresses one sensing window in the four-channel YI sensor. Experimental tests show that the implementation of the microfluidics reduces the response time of the sensor from 100s, as achieved with a bulky cuvette, to 4s. Monitoring the anti-human serum albumine/human serum albumine (alpha-HSA/HSA) immunoreaction demonstrates the feasibility to use the microfluidic sensing system for immunosensing applications. In this case, a better discrimination between the bulk refractive index change and the layer formation can be made, resulting into higher accuracy and offering the prospect of being able to use the kinetics of the immunoreaction. The microfluidic sensing system shows an average phase resolution of 7 x 10(-5) x 2pi for different pairs of channels, which at the given interaction length of 4 mm corresponds to a refractive index resolution of 6 x 10(-8), being equivalent to a protein mass coverage resolution of 20 fg/mm2.

  6. Integrated optical transceiver with electronically controlled optical beamsteering

    Energy Technology Data Exchange (ETDEWEB)

    Davids, Paul; DeRose, Christopher; Tauke-Pedretti, Anna

    2017-08-22

    A beam-steering optical transceiver is provided. The transceiver includes one or more modules, each comprising an antenna chip and a control chip bonded to the antenna chip. Each antenna chip has a feeder waveguide, a plurality of row waveguides that tap off from the feeder waveguide, and a plurality of metallic nanoantenna elements arranged in a two-dimensional array of rows and columns such that each row overlies one of the row waveguides. Each antenna chip also includes a plurality of independently addressable thermo-optical phase shifters, each configured to produce a thermo-optical phase shift in a respective row. Each antenna chip also has, for each row, a row-wise heating circuit configured to produce a respective thermo-optic phase shift at each nanoantenna element along its row. The control chip includes controllable current sources for the independently addressable thermo-optical phase shifters and the row-wise heating circuits.

  7. Experimental Investigation of Integrated Optical Intensive Impulse Electric Field Sensors

    Institute of Scientific and Technical Information of China (English)

    SUN Bao; CHEN Fu-Shen

    2009-01-01

    We design and fabricate an integrated optical electric field sensor with segmented electrode for intensive im-pulse electric field measurement. The integrated optical sensor is based on a Mach-Zehnder interferometer with segmented electrodes. The output/input character of the sensing system is analysed and measured. The max-imal detectable electric field range (-75 kV/m to 245 kV/m) is obtained by analysing the results. As a result, the integrated optics electric field sensing system is suitable for transient intensive electric field measurement investigation.

  8. Hybrid Integrated Silicon Microfluidic Platform for Fluorescence Based Biodetection

    Directory of Open Access Journals (Sweden)

    André Darveau

    2007-09-01

    Full Text Available The desideratum to develop a fully integrated Lab-on-a-chip device capable ofrapid specimen detection for high throughput in-situ biomedical diagnoses and Point-of-Care testing applications has called for the integration of some of the novel technologiessuch as the microfluidics, microphotonics, immunoproteomics and Micro ElectroMechanical Systems (MEMS. In the present work, a silicon based microfluidic device hasbeen developed for carrying out fluorescence based immunoassay. By hybrid attachment ofthe microfluidic device with a Spectrometer-on-chip, the feasibility of synthesizing anintegrated Lab-on-a-chip type device for fluorescence based biosensing has beendemonstrated. Biodetection using the microfluidic device has been carried out usingantigen sheep IgG and Alexafluor-647 tagged antibody particles and the experimentalresults prove that silicon is a compatible material for the present application given thevarious advantages it offers such as cost-effectiveness, ease of bulk microfabrication,superior surface affinity to biomolecules, ease of disposability of the device etc., and is thussuitable for fabricating Lab-on-a-chip type devices.

  9. Hybrid optical-thermal antennas for enhanced light focusing and local temperature control

    CERN Document Server

    Boriskina, Svetlana V; Tong, Jonathan K; Hsu, Wei-Chun; Chen, Gang

    2016-01-01

    Metal nanoantennas supporting localized surface plasmon resonances have become an indispensable tool in bio(chemical) sensing and nanoscale imaging applications. The high plasmon-enhanced electric field intensity in the visible or near-IR range that enables the above applications may also cause local heating of nanoantennas. We present a design of hybrid optical-thermal antennas that simultaneously enable intensity enhancement at the operating wavelength in the visible and nanoscale local temperature control. We demonstrate a possibility to reduce the hybrid antenna operating temperature via enhanced infrared thermal emission. We predict via rigorous numerical modeling that hybrid optical-thermal antennas that support high-quality-factor photonic-plasmonic modes enable up to two orders of magnitude enhancement of localized electric fields and of the optical power absorbed in the nanoscale metal volume. At the same time, the hybrid antenna temperature can be lowered by several hundred degrees with respect to i...

  10. Design and characterization of SiON integrated optics components for optical coherence tomography

    NARCIS (Netherlands)

    Nguyen, V. Duc; Kalkman, J.; Ismail, N.; Sun, F.; Worhoff, Kerstin; Driessen, A.; Pollnau, Markus; van Leeuwen, Ton

    2009-01-01

    Optical coherence tomography (OCT) is a technique for high resolution imaging of biological tissues with a depth range of a few millimeters. OCT is based on interferometry to enable depth ranging. Currently, optical components for OCT are rather bulky and expensive; the use of integrated optical

  11. Platforms for integrated nonlinear optics compatible with silicon integrated circuits

    CERN Document Server

    Moss, David J

    2014-01-01

    Nonlinear photonic chips are capable of generating and processing signals all-optically with performance far superior to that possible electronically - particularly with respect to speed. Although silicon has been the leading platform for nonlinear optics, its high two-photon absorption at telecommunications wavelengths poses a fundamental limitation. We review recent progress in CMOS-compatible platforms for nonlinear optics, focusing on Hydex glass and silicon nitride and briefly discuss the promising new platform of amorphous silicon. These material systems have opened up many new capabilities such as on-chip optical frequency comb generation, ultrafast optical pulse generation and measurement. We highlight their potential future impact as well as the challenges to achieving practical solutions for many key applications.

  12. Nonlinear Integrated Optical Waveguides in Chalcogenide Glasses

    Institute of Scientific and Technical Information of China (English)

    Yinlan; Ruan; Barry; Luther-Davies; Weitang; Li; Andrei; Rode; Marek; Samoc

    2003-01-01

    This paper reports on the study and measurement of the third order optical nonlinearity in bulk sulfide-based chalcogenide glasses; The fabrication process of the ultrafast laser deposited As-S-(Se)-based chalcogenide films and optical waveguides using two techniques: wet chemistry etching and plasma etching.

  13. Integrating 4G Optics (Conference Presentation)

    Science.gov (United States)

    Tabiryan, Nelson V.; Hwang, Jeoungyeon; Steeves, Diane M.; Kimball, Brian R.; Bunning, Timothy J.; White, Timothy J.

    2016-09-01

    The thickness of functional layers in liquid crystal photonics devices is negligibly small compared to the substrates. New opportunities provided by multilayer 4G optical systems require minimizing the thickness of each layer. We report about our progress made by developing technology of thin flexible substrates, functional polymer films, solid electro-optical layers, and graphene oxide based electro-conductive coatings.

  14. Glass-based integrated optical splitters: engineering oriented research

    Science.gov (United States)

    Hao, Yinlei; Zheng, Weiwei; Yang, Jianyi; Jiang, Xiaoqing; Wang, Minghua

    2010-10-01

    Optical splitter is one of most typical device heavily demanded in implementation of Fiber To The Home (FTTH) system. Due to its compatibility with optical fibers, low propagation loss, flexibility, and most distinguishingly, potentially costeffectiveness, glass-based integrated optical splitters made by ion-exchange technology promise to be very attractive in application of optical communication networks. Aiming at integrated optical splitters applied in optical communication network, glass ion-exchange waveguide process is developed, which includes two steps: thermal salts ion-exchange and field-assisted ion-diffusion. By this process, high performance optical splitters are fabricated in specially melted glass substrate. Main performance parameters of these splitters, including maximum insertion loss (IL), polarization dependence loss (PDL), and IL uniformity are all in accordance with corresponding specifications in generic requirements for optic branching components (GR-1209-CORE). In this paper, glass based integrated optical splitters manufacturing is demonstrated, after which, engineering-oriented research work results on glass-based optical splitter are presented.

  15. Population Dynamics and the Optical Absorption in Hybrid Metal Nanoparticle - Semiconductor Quantum dot Nanosystem

    CERN Document Server

    Kim, Nam-Chol; Ko, Myong-Chol; So, Guang Hyok; Kim, Il-Guang

    2015-01-01

    We studied theoretically the population dynamics and the absorption spectrum of hybrid nanosystem consisted of a matal nanoparticle (MNP) and a semiconductor quantum dot(SQD). We investigated the exciton-plasmon coupling effects on the population dynamics and the absorption properties of the nanostructure. Our results show that the nonlinear optical response of the hybrid nanosystem can be greatly enhanced or depressed due to the exciton-plasmon couplings. The results obtained here may have the potential applications of nanoscale optical devices such as optical switches and quantum devices such as a single photon transistor.

  16. Graphene nanopore with a self-integrated optical antenna.

    Science.gov (United States)

    Nam, SungWoo; Choi, Inhee; Fu, Chi-cheng; Kim, Kwanpyo; Hong, SoonGweon; Choi, Yeonho; Zettl, Alex; Lee, Luke P

    2014-10-08

    We report graphene nanopores with integrated optical antennae. We demonstrate that a nanometer-sized heated spot created by photon-to-heat conversion of a gold nanorod resting on a graphene membrane forms a nanoscale pore with a self-integrated optical antenna in a single step. The distinct plasmonic traits of metal nanoparticles, which have a unique capability to concentrate light into nanoscale regions, yield the significant advantage of parallel nanopore fabrication compared to the conventional sequential process using an electron beam. Tunability of both the nanopore dimensions and the optical characteristics of plasmonic nanoantennae are further achieved. Finally, the key optical function of our self-integrated optical antenna on the vicinity of graphene nanopore is manifested by multifold fluorescent signal enhancement during DNA translocation.

  17. Applications of hybrid diffuse optics for clinical management of adults after brain injury

    Science.gov (United States)

    Kim, Meeri Nam

    Information about cerebral blood flow (CBF) is valuable for clinical management of patients after severe brain injury. Unfortunately, current modalities for monitoring brain are often limited by hurdles that include high cost, low throughput, exposure to ionizing radiation, probe invasiveness, and increased risk to critically ill patients when transportation out of their room or unit is required. A further limitation of current technologies is an inability to provide continuous bedside measurements that are often desirable for unstable patients. Here we explore the clinical utility of diffuse correlation spectroscopy (DCS) as an alternative approach for bedside CBF monitoring. DCS uses the rapid intensity fluctuations of near-infrared light to derive a continuous measure of changes in blood flow without ionizing radiation or invasive probing. Concurrently, we employ another optical technique, called diffuse optical spectroscopy (DOS), to derive changes in cerebral oxyhemoglobin ( HbO2) and deoxyhemoglobin (Hb) concentrations. Our clinical studies integrate DCS with DOS into a single hybrid instrument that simultaneously monitors CBF and HbO2/Hb in the injured adult brain. The first parts of this dissertation present the motivations for monitoring blood flow in injured brain, as well as the theory underlying diffuse optics technology. The next section elaborates on details of the hybrid instrumentation. The final chapters describe four human subject studies carried out with these methods. Each of these studies investigates an aspect of the potential of the hybrid monitor in clinical applications involving adult brain. The studies include: (1) validation of DCS-measured CBF against xenon-enhanced computed tomography in brain-injured adults; (2) a study of the effects of age and gender on posture-change-induced CBF variation in healthy subjects; (3) a study of the efficacy of DCS/DOS for monitoring neurocritical care patients during various medical interventions such

  18. A multi-ring optical packet and circuit integrated network with optical buffering.

    Science.gov (United States)

    Furukawa, Hideaki; Shinada, Satoshi; Miyazawa, Takaya; Harai, Hiroaki; Kawasaki, Wataru; Saito, Tatsuhiko; Matsunaga, Koji; Toyozumi, Tatuya; Wada, Naoya

    2012-12-17

    We newly developed a 3 × 3 integrated optical packet and circuit switch-node. Optical buffers and burst-mode erbium-doped fiber amplifiers with the gain flatness are installed in the 3 × 3 switch-node. The optical buffer can prevent packet collisions and decrease packet loss. We constructed a multi-ring optical packet and circuit integrated network testbed connecting two single-ring networks and a client network by the 3 × 3 switch-node. For the first time, we demonstrated 244 km fiber transmission and 5-node hopping of multiplexed 14-wavelength 10 Gbps optical paths and 100 Gbps optical packets encapsulating 10 Gigabit Ethernet frames on the testbed. Error-free (frame error rate < 1 × 10(-4)) operation was achieved with optical packets of various packet lengths. In addition, successful avoidance of packet collisions by optical buffers was confirmed.

  19. Amplifying waveguide optical isolator with an integrated electromagnet

    OpenAIRE

    2007-01-01

    We have demonstrated an amplifying waveguide optical isolator with an integrated electromagnet. This provides a solution to the generally poor magnetic remanence of this type of isolator. The proof of principle is presented and optimization routes are discussed.

  20. Fibre-Optic Strain Measurement For Structural Integrity Monitoring

    NARCIS (Netherlands)

    Bruinsma, A.J.A.; Zuylen, P. van; Lamberts, C.W.; Krijger, A.J.T. de

    1984-01-01

    A method is demonstrated for monitoring the structural integrity of large structures, using an optical fibre. The strain distribution along the structure is monitored by measuring the attentuation of light along the length of the fibre.

  1. UV-written Integrated Optical 1xN Splitters

    DEFF Research Database (Denmark)

    Olivero, Massimo; Svalgaard, Mikael

    2006-01-01

    The first demonstration of UV-written, silica-on-silicon integrated optical 1×N power splitters with up to 32 outputs ports is presented. The fabricated components exhibit 450 nm bandwidth, low excess loss and good channel uniformity.......The first demonstration of UV-written, silica-on-silicon integrated optical 1×N power splitters with up to 32 outputs ports is presented. The fabricated components exhibit 450 nm bandwidth, low excess loss and good channel uniformity....

  2. Network Integration of Distributed Optical Fiber Temperature Sensor

    Institute of Scientific and Technical Information of China (English)

    Gui-Yan Li; Hong-Lin Liu; Zai-Xuan Zhang

    2008-01-01

    The integration of distributed optical fiber temperature sensor with supervisory control and data acquisition (SCADA) system is proposed and implemented. In the implementation of the integration, both the compatibility with traditional system and the characteristics of distributed optical fiber temperature sensor is considered before Modbus TCP/IP protocol is chosen. The protocol is implemented with open source component Indy. The Modbus TCP/IP protocol used in the system is proved to be fast and robust.

  3. A Miniaturized Optical Sensor with Integrated Gas Cell

    NARCIS (Netherlands)

    Ayerden, N.P.; Ghaderi, M.; De Graaf, G.; Wolffenbuttel, R.F.

    2015-01-01

    The design, fabrication and characterization of a highly integrated optical gas sensor is presented. The gas cell takes up most of the space in a microspectrometer and is the only component that has so far not been miniaturized. Using the tapered resonator cavity of a linear variable optical filter

  4. Nonlinear Optics in Doped Silica Glass Integrated Waveguide Structures

    CERN Document Server

    Duchesne, David; Razzari, Luca; Morandotti, Roberto; Little, Brent; Chu, Sai T; Moss, David J

    2015-01-01

    Integrated photonic technologies are rapidly becoming an important and fundamental milestone for wideband optical telecommunications. Future optical networks have several critical requirements, including low energy consumption, high efficiency, greater bandwidth and flexibility, which must be addressed in a compact form factor.

  5. SiON technology for integrated optical sensors

    NARCIS (Netherlands)

    Lambeck, P.V.; Wörhoff, Kerstin; Righini, Giancarlo C.

    2002-01-01

    Silicon oxynitride (SiON)- technology has been widely accepted for realizing integrated optical devices for application in optical telecommunication. Some of the severe requirements put in this field to devices and hence to technology are more relaxed in sensing applications, but other ones pop up i

  6. Optical amplification in photonic integrated circuits

    NARCIS (Netherlands)

    Pollnau, Markus

    2005-01-01

    The recent results in the field of fabrication, characterization, and applications of optical waveguides in doped hard crystalline materials, specifically in Ti-doped sapphire and Yb-doped $KY(WO_4)_2$, are reviewed.

  7. Optical Image Classification Using Optical/digital Hybrid Image Processing Systems.

    Science.gov (United States)

    Li, Xiaoyang

    1990-01-01

    Offering parallel and real-time operations, optical image classification is becoming a general technique in the solution of real-life image classification problems. This thesis investigates several algorithms for optical realization. Compared to other statistical pattern recognition algorithms, the Kittler-Young transform can provide more discriminative feature spaces for image classification. We shall apply the Kittler-Young transform to image classification and implement it on optical systems. A feature selection criterion is designed for the application of the Kittler -Young transform to image classification. The realizations of the Kittler-Young transform on both a joint transform correlator and a matrix multiplier are successively conducted. Experiments of applying this technique to two-category and three-category problems are demonstrated. To combine the advantages of the statistical pattern recognition algorithms and the neural network models, processes using the two methods are studied. The Karhunen-Loeve Hopfield model is developed for image classification. This model has significant improvement in the system capacity and the capability of using image structures for more discriminative classification processes. As another such hybrid process, we propose the feature extraction perceptron. The application of feature extraction techniques to the perceptron shortens its learning time. An improved activation function of neurons (dynamic activation function), its design and updating rule for fast learning process and high space-bandwidth product image classification are also proposed. We have shortened by two-thirds the learning time on the feature extraction perceptron as compared with the original perceptron. By using this architecture, we have shown that the classification performs better than both the Kittler-Young transform and the original perceptron.

  8. Optical Simulation and Experimental Verification of a Fresnel Solar Concentrator with a New Hybrid Second Optical Element

    Directory of Open Access Journals (Sweden)

    Guiqiang Li

    2016-01-01

    Full Text Available Fresnel solar concentrator is one of the most common solar concentrators in solar applications. For high Fresnel concentrating PV or PV/T systems, the second optical element (SOE is the key component for the high optical efficiency at a wider deflection angle, which is important for overcoming unavoidable errors from the tacking system, the Fresnel lens processing and installment technology, and so forth. In this paper, a new hybrid SOE was designed to match the Fresnel solar concentrator with the concentration ratio of 1090x. The ray-tracing technology was employed to indicate the optical properties. The simulation outcome showed that the Fresnel solar concentrator with the new hybrid SOE has a wider deflection angle scope with the high optical efficiency. Furthermore, the flux distribution with different deviation angles was also analyzed. In addition, the experiment of the Fresnel solar concentrator with the hybrid SOE under outdoor condition was carried out. The verifications from the electrical and thermal outputs were all made to analyze the optical efficiency comprehensively. The optical efficiency resulting from the experiment is found to be consistent with that from the simulation.

  9. A Hybrid Thermopneumatic and Electrostatic Microvalve with Integrated Position Sensing

    Directory of Open Access Journals (Sweden)

    Kensall D. Wise

    2012-04-01

    Full Text Available This paper presents a low-power hybrid thermopneumatic microvalve with an electrostatic hold and integrated valve plate position sensing. This combination of actuators in a single structure enables a high throw and force actuator with low energy consumption, a combination that is difficult to otherwise achieve. The completed 7.5 mm × 10.3 mm × 1.5 mm valve has an open flow rate of 8 sccm at 600 Pa, a leak rate of 2.2 × 10−3 sccm at 115 kPa, a open-to-closed fluidic conductance ratio of nearly one million, an actuation time of 430 ms at 250 mW, and a required power of 90 mW while closed. It additionally requires no power to open, and has a built-in capacitive position sensor with a sensitivity of 9.8 fF/kPa. The paper additionally presents analytical models of the valve components, design tradeoffs, and guidelines for achieving an optimized device.

  10. Proposal for loadable and erasable optical memory unit based on dual active microring optical integrators

    Science.gov (United States)

    Ding, Yunhong; Zhang, Xiaobei; Zhang, Xinliang; Huang, Dexiu

    2008-11-01

    A novel approach for loadable and erasable optical memory unit based on dual microring optical integrators is proposed and studied. The optical integrator, which can generate an optical step function for data storing, is synthesized using active media for loss compensation and a tunable phase shifter for data reading at any time. The input data into the memory is return-to-zero (RZ) signal, and the output data read from the memory is also RZ format with a narrower pulse width. An optical digital register based on the proposed optical memory unit is also investigated and simulated, which shows the potential for large scale data storage and serial-to-parallel data conversion. A great number of such memory units can be densely integrated on a photonic circuit for future large scale data storage and buffer.

  11. Development of optical packet and circuit integrated ring network testbed.

    Science.gov (United States)

    Furukawa, Hideaki; Harai, Hiroaki; Miyazawa, Takaya; Shinada, Satoshi; Kawasaki, Wataru; Wada, Naoya

    2011-12-12

    We developed novel integrated optical packet and circuit switch-node equipment. Compared with our previous equipment, a polarization-independent 4 × 4 semiconductor optical amplifier switch subsystem, gain-controlled optical amplifiers, and one 100 Gbps optical packet transponder and seven 10 Gbps optical path transponders with 10 Gigabit Ethernet (10GbE) client-interfaces were newly installed in the present system. The switch and amplifiers can provide more stable operation without equipment adjustments for the frequent polarization-rotations and dynamic packet-rate changes of optical packets. We constructed an optical packet and circuit integrated ring network testbed consisting of two switch nodes for accelerating network development, and we demonstrated 66 km fiber transmission and switching operation of multiplexed 14-wavelength 10 Gbps optical paths and 100 Gbps optical packets encapsulating 10GbE frames. Error-free (frame error rate < 1×10(-4)) operation was achieved with optical packets of various packet lengths and packet rates, and stable operation of the network testbed was confirmed. In addition, 4K uncompressed video streaming over OPS links was successfully demonstrated.

  12. ULTRA-HIGH BW OPTICAL COMMUNICATION USING OXYGEN PLASMA ASSISTED InP BASED HYBRID Si LASER

    Directory of Open Access Journals (Sweden)

    PRATTAY BIN ABDUL WAHAB

    2010-12-01

    Full Text Available This paper demonstrates the development of a hybrid integration platform to build major electrically driven photonic active devices: silicon evanescent DFB lasers, silicon evanescent amplifiers, silicon evanescent waveguide photo-detectors or pre-amplified photo-detectors on a single silicon platform consisting of III-V gain layers with passive waveguide for board to board and for chip to chip optical communication for tera scale computing. The structural description proposed here may push forward the manufacturing of photonic ICs tomake high speed communicational imaginings to reality and to start a new era.

  13. Neuromorphic opto-electronic integrated circuits for optical signal processing

    Science.gov (United States)

    Romeira, B.; Javaloyes, J.; Balle, S.; Piro, O.; Avó, R.; Figueiredo, J. M. L.

    2014-08-01

    The ability to produce narrow optical pulses has been extensively investigated in laser systems with promising applications in photonics such as clock recovery, pulse reshaping, and recently in photonics artificial neural networks using spiking signal processing. Here, we investigate a neuromorphic opto-electronic integrated circuit (NOEIC) comprising a semiconductor laser driven by a resonant tunneling diode (RTD) photo-detector operating at telecommunication (1550 nm) wavelengths capable of excitable spiking signal generation in response to optical and electrical control signals. The RTD-NOEIC mimics biologically inspired neuronal phenomena and possesses high-speed response and potential for monolithic integration for optical signal processing applications.

  14. Compressive sensing in a photonic link with optical integration

    DEFF Research Database (Denmark)

    Chen, Ying; Yu, Xianbin; Chi, Hao

    2014-01-01

    In this Letter, we present a novel structure to realize photonics-assisted compressive sensing (CS) with optical integration. In the system, a spectrally sparse signal modulates a multiwavelength continuous-wave light and then is mixed with a random sequence in optical domain. The optical signal......, which is equivalent to the function of integration required in CS. A proof-of-concept experiment with four wavelengths, corresponding to a compression factor of 4, is demonstrated. More simulation results are also given to show the potential of the technique....

  15. Optical nanofiber integrated into an optical tweezers for particle probing and manipulation

    CERN Document Server

    Frawley, Mary C; Truong, Viet Giang; Chormaic, Sile Nic

    2014-01-01

    We present an integrated platform for particle manipulation consisting of a combined optical nanofiber and optical tweezers system. Individual silica microspheres were introduced to the nanofiber at arbitrary points using the optical tweezers, thereby producing pronounced dips in the fiber transmission. We show that such consistent and reversible transmission modulations depend on both particle and fiber diameter, and may be used as a reference point for in-situ nanofiber or particle size calibration. Particle arrays can be released from the optical tweezers onto the nanofiber and are propelled along the fiber length via guided light. We also demonstrate how the optical tweezers can be used to create a "particle jet" to feed a supply of microspheres to the nanofiber surface, forming a particle conveyor belt. This integrated optical platform provides a method for selective evanescent field manipulation of micron-sized particles and may facilitate studies of optical binding and light-particle interaction dynami...

  16. All-optically integrated multimodality imaging system: combined photoacoustic microscopy, optical coherence tomography, and fluorescence imaging

    Science.gov (United States)

    Chen, Zhongjiang; Yang, Sihua; Xing, Da

    2016-10-01

    We have developed a multimodality imaging system by optically integrating all-optical photoacoustic microscopy (AOPAM), optical coherence tomography (OCT) and fluorescence microscopy (FLM) to provide complementary information including optical absorption, optical back-scattering and fluorescence contrast of biological tissue. By sharing the same low-coherence Michelson interferometer, AOPAM and OCT could be organically optically combined to obtain the absorption and scattering information of the biological tissues. Also, owing to using the same laser source and objective lens, intrinsically registered photoacoustic and fluorescence signals are obtained to present the radiative and nonradiative transition process of absorption. Simultaneously photoacoustic angiography, tissue structure and fluorescence molecular in vivo images of mouse ear were acquired to demonstrate the capabilities of the optically integrated trimodality imaging system, which can present more information to study tumor angiogenesis, vasculature, anatomical structure and microenvironments in vivo.

  17. Hybrid optical-thermal devices and materials for light manipulation and radiative cooling

    CERN Document Server

    Boriskina, Svetlana V; Hsu, Wei-Chun; Weinstein, Lee; Huang, Xiaopeng; Loomis, James; Xu, Yanfei; Chen, Gang

    2015-01-01

    We report on optical design and applications of hybrid meso-scale devices and materials that combine optical and thermal management functionalities owing to their tailored resonant interaction with light in visible and infrared frequency bands. We outline a general approach to designing such materials, and discuss two specific applications in detail. One example is a hybrid optical-thermal antenna with sub-wavelength light focusing, which simultaneously enables intensity enhancement at the operating wavelength in the visible and reduction of the operating temperature. The enhancement is achieved via light recycling in the form of whispering-gallery modes trapped in an optical microcavity, while cooling functionality is realized via a combination of reduced optical absorption and radiative cooling. The other example is a fabric that is opaque in the visible range yet highly transparent in the infrared, which allows the human body to efficiently shed energy in the form of thermal emission. Such fabrics can find...

  18. An Object Detection Method Using Wavelet Optical Flow and Hybrid Linear-Nonlinear Classifier

    Directory of Open Access Journals (Sweden)

    Pengcheng Han

    2013-01-01

    Full Text Available We propose a new computational intelligence method using wavelet optical flow and hybrid linear-nonlinear classifier for object detection. With the existing optical flow methods, it is difficult to accurately estimate moving objects with diverse speeds. We propose a wavelet-based optical flow method, which uses wavelet decomposition in optical flow motion estimation. The algorithm can accurately detect moving objects with variable speeds in a scene. In addition, we use the hybrid linear-nonlinear classifier (HLNLC to classify moving objects and static background. HLNLC transforms a nonoptimal scalar variable into its likelihood ratio and uses a scalar quantity as the decision variable. This approach is appropriate for the classification of optical flow feature vectors with unequal variance matrices. The experimental results confirm that our proposed object detection method has an improved accuracy and computation efficiency over other state-of-the-art methods.

  19. A Software Tool for Integrated Optical Design Analysis

    Science.gov (United States)

    Moore, Jim; Troy, Ed; DePlachett, Charles; Montgomery, Edward (Technical Monitor)

    2001-01-01

    Design of large precision optical systems requires multi-disciplinary analysis, modeling, and design. Thermal, structural and optical characteristics of the hardware must be accurately understood in order to design a system capable of accomplishing the performance requirements. The interactions between each of the disciplines become stronger as systems are designed lighter weight for space applications. This coupling dictates a concurrent engineering design approach. In the past, integrated modeling tools have been developed that attempt to integrate all of the complex analysis within the framework of a single model. This often results in modeling simplifications and it requires engineering specialist to learn new applications. The software described in this presentation addresses the concurrent engineering task using a different approach. The software tool, Integrated Optical Design Analysis (IODA), uses data fusion technology to enable a cross discipline team of engineering experts to concurrently design an optical system using their standard validated engineering design tools.

  20. Third-order nonlinear optical response of Ag-CdSe/PVA hybrid nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Tripathi, S.K.; Kaur, Ramneek; Kaur, Jaspreet; Sharma, Mamta [Panjab University, Department of Physics, Center of Advanced Study in Physics, Chandigarh (India)

    2015-09-15

    Hybrid nanocomposites of II-VI semiconductor nanoparticles are gaining great interest in nonlinear optoelectronic devices. Present work includes the characterization of CdSe polymer nanocomposite prepared by chemical in situ technique. From X-ray diffraction, the hexagonal wurtzite structure of nanoparticles has been confirmed with spherical morphology from transmission electron microscopy. Ag-CdSe hybrid polymer nanocomposite has been prepared chemically at different Ag concentrations. The presence of Ag in hybrid nanocomposite has been confirmed with energy-dispersive X-ray spectroscopy. The effect of varying Ag concentration on the linear and nonlinear optical properties of the nanocomposites has been studied. In linear optical parameters, the linear absorption coefficient, refractive index, extinction coefficient and optical conductivity have been calculated. The third-order nonlinear optical properties have been observed with open- and closed-aperture Z-scan technique. The large nonlinear refractive index ∝10{sup -5} cm{sup 2}/W with self-focusing behaviour is due to the combined effect of quantum confinement and thermo-optical effects. The enhanced nonlinearity with increasing Ag content is due to the surface plasmon resonance, which enhances the local electric field near the nanoparticle surface. Thus, Ag-CdSe hybrid polymer nanocomposite has favourable nonlinear optical properties for various optoelectronic applications. (orig.)

  1. Synergistically Enhanced Optical Limiting Property of Graphene Oxide Hybrid Materials Functionalized with Pt Complexes.

    Science.gov (United States)

    Liu, Rui; Hu, Jinyang; Zhu, Senqiang; Lu, Jiapeng; Zhu, Hongjun

    2017-09-12

    Recently, graphene-based materials have become well-known nonlinear optical materials for the potential application of laser protection. Two new graphene oxide-platinum  complex (GO-Pt) hybrid materials (GO-Pt-1, GO-Pt-2) have been fabricated through covalent modification and electrostatic adsorption of different Pt complexes with GO. The structural and photophysical properties of the resultant hybrid materials were studied. The nonlinear optical properties and optical power limiting (OPL) performance of Pt complexes, GO, and GO-Pt hybrid materials were investigated by using Z-scan measurements at 532 nm. At the same transmittance, the results illustrate that functionalization of GO makes GO-Pt hybrid materials possess better nonlinear optical properties and OPL performance than individual Pt complexes and GO due to a combination of nonlinear scattering, nonlinear absorption, and photoinduced electron and energy transfer between GO and Pt complex moieties. Furthermore, the nonlinear optics and OPL performance of GO-Pt-2 are better than those of GO-Pt-1, due to not only the excellent optical limiting of Pt-2 and more molecules per area of GO but also the way of combination of Pt-2 and GO.

  2. Proposed smart integrated-optical preprocessor using holographic subtraction

    Science.gov (United States)

    Verber, C. M.; Vahey, D. W.

    1979-01-01

    The paper presents a proposed integrated-optical preprocessor with a holographic subtraction. It is based on an optical analog of a set of N analog voltages formed by passing an optical plane wave, confined in an electrooptic waveguide, under a set of N electrodes to which the voltages are applied; in the limit in which diffraction is ignored, the wavefront of the emerging guided wave will have superimposed upon it N discrete phase shifts. Processors which operate upon voltages encoded in this manner are being fabricated; they include a comparator in which incoming data are compared to a holographic record of the optical analog of a reference set, and a 'smart' system based upon holographic self-subtraction, in which the processor can independently adapt to changes in background information. The preprocessor operation is described in the screening, identification, and the self-subtraction modes, and implementation of devices in an integrated optical configuration is discussed.

  3. Optical Leaky-Wave Antenna Integrated in Ring Resonator

    CERN Document Server

    Guclu, Caner; Boyraz, Ozdal; Capolino, Filippo

    2014-01-01

    A leaky-wave antenna at optical frequencies is designed and integrated with a ring resonator at 1550 nm wavelength. The leaky wave is generated by using periodic perturbations in the integrated dielectric waveguide that excite the -1 spatial harmonic. The antenna consists of a dielectric waveguides with semiconductor corrugations, and it is compatible with CMOS fabrication technology. We show that integrating the leaky wave antenna in an optical ring resonator that is fed by directional couplers, we can improve the electronic control of the radiation through carrier injection into the semiconductor corrugations.

  4. Progresses in 3D integral imaging with optical processing

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Corral, Manuel; Martinez-Cuenca, Raul; Saavedra, Genaro; Navarro, Hector; Pons, Amparo [Department of Optics. University of Valencia. Calle Doctor Moliner 50, E46 100, Burjassot (Spain); Javidi, Bahram [Electrical and Computer Engineering Department, University of Connecticut, Storrs, CT 06269-1157 (United States)], E-mail: manuel.martinez@uv.es

    2008-11-01

    Integral imaging is a promising technique for the acquisition and auto-stereoscopic display of 3D scenes with full parallax and without the need of any additional devices like special glasses. First suggested by Lippmann in the beginning of the 20th century, integral imaging is based in the intersection of ray cones emitted by a collection of 2D elemental images which store the 3D information of the scene. This paper is devoted to the study, from the ray optics point of view, of the optical effects and interaction with the observer of integral imaging systems.

  5. Integrated Diffractive Optics for Surface Ion Traps

    Science.gov (United States)

    Streed, Erik; Ghadimi, Moji; Blums, Valdis; Norton, Benjamin; Connor, Paul; Amini, Jason; Volin, Curtis; Lobino, Mirko; Kielpinski, David

    2016-05-01

    Photonic interconnects are a bottleneck to achieving large-scale trapped ion quantum computing. We have modified a Georgia Tech Research Institute microwave chip trap by using e-beam lithography to write reflective diffractive collimating optics (80 μm x 127 μm, f=58.6 μm, λ=369.5nm) on the center electrode. The optics have an NA of 0.55 x 0.73, capturing 13.2% of the solid angle. To evaluate the optics 174Yb+ was loaded by isotope selective photo-ionization from a thermal oven and then shuttled to imaging sites. Near diffraction limited sub-wavelength ion images were obtained with an observed spot sized FWHM of 338 nm x 268 nm vs. a diffraction limit of 336 nm x 257 nm. The total photon collection efficiency was measured to be 5.2+/-1.2%. Coupling into a single mode fiber of up to 2.0+/-0.6% was observed, limited by mismatch in the coupling optics. Image mode quality indicates coupling up to 4% may be possible. Funding from Australian Research Council and IARPA.

  6. Hybrid viscous damper with filtered integral force feedback control

    DEFF Research Database (Denmark)

    Høgsberg, Jan; Brodersen, Mark L.

    2016-01-01

    In hybrid damper systems active control devices are usually introduced to enhance the performance of otherwise passive dampers. In the present paper a hybrid damper concept is comprised of a passive viscous damper placed in series with an active actuator and a force sensor. The actuator motion...

  7. Hybrid optical-fibre/geopolymer sensors for structural health monitoring of concrete structures

    Science.gov (United States)

    Perry, M.; Saafi, M.; Fusiek, G.; Niewczas, P.

    2015-04-01

    In this work, we demonstrate hybrid optical-fibre/geopolymer sensors for monitoring temperature, uniaxial strain and biaxial strain in concrete structures. The hybrid sensors detect these measurands via changes in geopolymer electrical impedance, and via optical wavelength measurements of embedded fibre Bragg gratings. Electrical and optical measurements were both facilitated by metal-coated optical fibres, which provided the hybrid sensors with a single, shared physical path for both voltage and wavelength signals. The embedded fibre sensors revealed that geopolymer specimens undergo 2.7 mɛ of shrinkage after one week of curing at 42 °C. After curing, an axial 2 mɛ compression of the uniaxial hybrid sensor led to impedance and wavelength shifts of 7 × 10-2 and -2 × 10-4 respectively. The typical strain resolution in the uniaxial sensor was 100 μ \\varepsilon . The biaxial sensor was applied to the side of a concrete cylinder, which was then placed under 0.6 mɛ of axial, compressive strain. Fractional shifts in impedance and wavelength, used to monitor axial and circumferential strain, were 3 × 10-2 and 4 × 10-5 respectively. The biaxial sensor’s strain resolution was approximately 10 μ \\varepsilon in both directions. Due to several design flaws, the uniaxial hybrid sensor was unable to accurately measure ambient temperature changes. The biaxial sensor, however, successfully monitored local temperature changes with 0.5 °C resolution.

  8. Optical fiber-based core-shell coaxially structured hybrid cells for self-powered nanosystems

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Caofeng; Zhu, Guang [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia (United States); Guo, Wenxi [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia (United States); State Key Laboratory of Physical Chemistry of Solid Surfaces, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Dong, Lin [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia (United States); School of Materials Science and Enginnering, Zhenzhou University, Zhenghou 450001 (China); Wang, Zhong Lin [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia (United States); Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, Beijing (China)

    2012-07-03

    An optical fiber-based 3D hybrid cell consisting of a coaxially structured dye-sensitized solar cell (DSSC) and a nanogenerator (NG) for simultaneously or independently harvesting solar and mechanical energy is demonstrated. The current output of the hybrid cell is dominated by the DSSC, and the voltage output is dominated by the NG; these can be utilized complementarily for different applications. The output of the hybrid cell is about 7.65 {mu}A current and 3.3 V voltage, which is strong enough to power nanodevices and even commercial electronic components. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Optical absorption and electrical transport in hybrid TiO2 and polymer nanocomposite films

    Science.gov (United States)

    Zhou, Xi-Song; Li, Zheng; Wang, Ning; Lin, Yuan-Hua; Nan, Ce-Wen

    2006-06-01

    Hybrid nanofilms of poly(2-methoxy-5-ethylhexyloxy-1,4-phenylene)vinylene (MEH-PPV) and anatase-TiO2 nanoparticles were prepared. The results showed that the optical absorption spectra and electrical transport properties of the TiO2/MEH-PPV nanocomposite films were strongly dependent on the particle size and concentration of TiO2 nanoparticles in the hybrid films. In comparison with pure TiO2 nanofilms, the hybrid TiO2/MEH-PPV films presented a shift of the absorption edge to the lower-energy region, and an obvious nonlinear current-voltage characteristic.

  10. Architectural and operational considerations emerging from hybrid RF-optical network loading simulations

    Science.gov (United States)

    Chen, Yijiang; Abraham, Douglas S.; Heckman, David P.; Kwok, Andrew; MacNeal, Bruce E.; Tran, Kristy; Wu, Janet P.

    2016-03-01

    A technology demonstration of free space optical communication at interplanetary distances is planned via one or more future NASA deep-space missions. Such demonstrations will "pave the way" for operational use of optical communications on future robotic/potential Human missions. Hence, the Deep Space Network architecture will need to evolve. Preliminary attempts to model the anticipated future mission set and simulate how well it loads onto assumed architectures with combinations of RF and optical apertures have been evaluated. This paper discusses the results of preliminary loading simulations for hybrid RF-optical network architectures and highlights key mission and ground infrastructure considerations that emerge.

  11. Magneto-optic transmittance modulation observed in a hybrid graphene–split ring resonator terahertz metasurface

    Energy Technology Data Exchange (ETDEWEB)

    Zanotto, Simone; Pitanti, Alessandro [NEST, Istituto Nanoscienze–CNR and Scuola Normale Superiore, Piazza San Silvestro 12, 56127 Pisa (Italy); Lange, Christoph; Maag, Thomas; Huber, Rupert [Department of Physics, University of Regensburg, 93040 Regensburg (Germany); Miseikis, Vaidotas; Coletti, Camilla [CNI@NEST, Istituto Italiano di Tecnologia, P.za S. Silvestro 12, 56127 Pisa (Italy); Degl' Innocenti, Riccardo [Cavendish Laboratory, University of Cambridge, J. J. Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Baldacci, Lorenzo [Scuola Superiore Sant' Anna, Institute of Life Sciences, P.za Martiri della Libertà 33, 56127 Pisa (Italy); Tredicucci, Alessandro [NEST, Istituto Nanoscienze-CNR and Dipartimento di Fisica “E. Fermi,” Università di Pisa, L.go Pontecorvo 3, 56127 Pisa (Italy)

    2015-09-21

    By placing a material in close vicinity of a resonant optical element, its intrinsic optical response can be tuned, possibly to a wide extent. Here, we show that a graphene monolayer, spaced a few tenths of nanometers from a split ring resonator metasurface, exhibits a magneto-optical response which is strongly influenced by the presence of the metasurface itself. This hybrid system holds promises in view of thin optical modulators, polarization rotators, and nonreciprocal devices, in the technologically relevant terahertz spectral range. Moreover, it could be chosen as the playground for investigating the cavity electrodynamics of Dirac fermions in the quantum regime.

  12. Integrating free-space optical communication links with existing WiFi (WiFO) network

    Science.gov (United States)

    Liverman, S.; Wang, Q.; Chu, Y.; Duong, T.; Nguyen-Huu, D.; Wang, S.; Nguyen, T.; Wang, A. X.

    2016-02-01

    Recently, free-space optical (FSO) systems have generated great interest due to their large bandwidth potential and a line-of-sight physical layer of protection. In this paper, we propose WiFO, a novel hybrid system, FSO downlink and WiFi uplink, which will integrate currently available WiFi infrastructure with inexpensive infrared light emitting diodes. This system takes full advantage of the mobility inherent in WiFi networks while increasing the downlink bandwidth available to each end user. We report the results of our preliminary investigation that show the capabilities of our prototype design in terms of bandwidth, bit error rates, delays and transmission distances.

  13. CAD integration: opening up new optical design possibilities; Technical Digest

    Science.gov (United States)

    Haumonte, Jean-Baptiste; Venturino, Jean-Claude

    2005-05-01

    The development of optical design and analysis tools in a CAD software can help to optimise the design, size and performance of tomorrow's consumer produtcs. While optics was still held back by software limitations, CAD programs were moving forward in leaps and bounds, improving manufacturing technologies and making it possible to design and produce highly innovative and sophisticated products. The problem was that in the past, 'traditional' optical design programs were only able to simulate spherical and aspherical lenses, meaning that the optical designers were limited to designing systems which were a series of imperfect lenses, each one correcting the last. That is why OPTIS has created the first optical design program to be fully integrated into a CAD program. The technology is available from OPTIS in an integrated SOLIDWORKS or CATIA V5 version. Users of this software can reduce the number of lenses needed in a system. Designers will now have access to complex surfaces such as NURBS meaning they will now be able to define free shape progressive lenses and even improve on optical performances using fewer lenses. This revolutionary technology will allow mechanical designers to work on optical systems and to shre information with optical designers for the first time. Previously not possible in a CAD program you may now determine all the optical performances of any optical system, providing first order and third order performances, sequential and non-sequential ray-tracing, wavefront surfaces, point spread function, MTF, spot-diagram, using real optical surfaces and guaranteeing the mechanical precision necessary for an optical system.

  14. Integration of hybrid wireless networks in cloud services oriented enterprise information systems

    Science.gov (United States)

    Li, Shancang; Xu, Lida; Wang, Xinheng; Wang, Jue

    2012-05-01

    This article presents a hybrid wireless network integration scheme in cloud services-based enterprise information systems (EISs). With the emerging hybrid wireless networks and cloud computing technologies, it is necessary to develop a scheme that can seamlessly integrate these new technologies into existing EISs. By combining the hybrid wireless networks and computing in EIS, a new framework is proposed, which includes frontend layer, middle layer and backend layers connected to IP EISs. Based on a collaborative architecture, cloud services management framework and process diagram are presented. As a key feature, the proposed approach integrates access control functionalities within the hybrid framework that provide users with filtered views on available cloud services based on cloud service access requirements and user security credentials. In future work, we will implement the proposed framework over SwanMesh platform by integrating the UPnP standard into an enterprise information system.

  15. Measurement of the thermo-optical effect of integrated waveguides

    Science.gov (United States)

    Kremmel, Johannes; Lamprecht, Tobias; Michler, Markus

    2016-05-01

    Thermo-optical switches are widely used in integrated optics and various types of integrated optical structures have been reported in literature. These structures include, but are not limited to Mach-Zehnder-Interferometer (MZI) switches and digital optical switches. The thermo-optical effect depends on the refractive index, the polarizability and the density of a material. The polarizability effect can often be neglected and the change of refractive index is dominated by a density change due to the thermal expansion of the material. We report herein a new method to measure the thermo-optical effect of waveguides directly, using integrated MZIs fabricated in polymer waveguide technology. Common methods rely on macroscopic samples, but the properties can differ significantly for micro-structured waveguides. Using a floodlight halogen rod lamp and metal-shields, we realized a radiation heater with a trapezoidal-shaped heating pattern. While the heating occurred from the bottom side, a thermocouple was placed on top of the sample. By dynamically measuring the temperature and the corresponding output-power of the MZI, the temperature difference between constructive and destructive interference can be determined. Multiple measurements of different sample MZIs exhibit an average thermo-optical coefficient (TOC) of 1.6 ∗ 10-4 1/K .

  16. Technological and Physical Compatibilities in Hybrid Integration of Laser and Monolithic Integration of Waveguide, Photodetector and CMOS Circuits on Silicon

    NARCIS (Netherlands)

    Zhou, M.J.; Ikkink, T.; Chalmers, J.; Kranenburg, H. van; Albers, H.; Holleman, J.; Lambeck, P.V.; Joppe, J.L.; Bekman, H.H.P.T.; Krijger, A.J.T. de

    1994-01-01

    In this paper, technological and physical compatibilities in hybrid integration of AlInGaP laser and monolithic integration of ZnO monomode waveguide, pin-photodetector, CMOS circuits for laser power control and signal amplification on silicon substrate are studied. Prospective problems and their po

  17. Technological and physical compatibilities in hybrid integration of laser and monolithic integration of waveguide, photodetector and CMOS circuits on silicon

    NARCIS (Netherlands)

    Zhou, Ming-Jiang; Ikkink, Ton; Chalmers, John; Kranenburg, van Herma; Albers, Hans; Holleman, Jisk; Lambeck, Paul; Joppe, Jan Leendert; Bekman, Herman; Krijger, de Ton; Lambeck, P.V.

    1994-01-01

    In this paper, technological and physical compatibilities in hybrid integration of AlInGaP laser and monolithic integration of ZnO monomode waveguide, pin-photodetector, CMOS circuits for laser power control and signal amplification on silicon substrate are studied. Prospective problems and their po

  18. Integration of Magneto-Optical Materials for Novel Optical Devices & Magnetophotonic Crystals Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This work proposes to capitalize on our Phase I success in monolithically integrating magneto-optic and magnetic materials with semiconductor platforms in order to...

  19. Antenna-coupled silicon-organic hybrid integrated photonic crystal modulator for broadband electromagnetic wave detection

    CERN Document Server

    Zhang, Xingyu; Subbaraman, Harish; Wang, Shiyi; Zhan, Qiwen; Luo, Jingdong; Jen, Alex K -Y; Chung, Chi-jui; Yan, Hai; Pan, Zeyu; Nelson, Robert L; Lee, Charles Y -C; Chen, Ray T

    2015-01-01

    In this work, we design, fabricate and characterize a compact, broadband and highly sensitive integrated photonic electromagnetic field sensor based on a silicon-organic hybrid modulator driven by a bowtie antenna. The large electro-optic (EO) coefficient of organic polymer, the slow-light effects in the silicon slot photonic crystal waveguide (PCW), and the broadband field enhancement provided by the bowtie antenna, are all combined to enhance the interaction of microwaves and optical waves, enabling a high EO modulation efficiency and thus a high sensitivity. The modulator is experimentally demonstrated with a record-high effective in-device EO modulation efficiency of r33=1230pm/V. Modulation response up to 40GHz is measured, with a 3-dB bandwidth of 11GHz. The slot PCW has an interaction length of 300um, and the bowtie antenna has an area smaller than 1cm2. The bowtie antenna in the device is experimentally demonstrated to have a broadband characteristics with a central resonance frequency of 10GHz, as we...

  20. Detection of Prorocentrum donghaiense using sandwich hybridization integrated with nuclease protection assay

    Institute of Scientific and Technical Information of China (English)

    CHEN Jie; ZHEN Yu; MI Tiezhu; YU Zhigang

    2009-01-01

    Prorocentrum donghaiense is an important harmful algae bloom (HAB) causing creature in China's seas, and the conventional visual detection can not cope with long-term monitoring and highthroughput sampling projects. An assay for P. donghaiense with sandwich hybridization integrated with nuclease protection assay (NPA-SH) was established. Tests with mixed samples and spiked field ones confirmed its good specificity and sensitivity. The cell number of P. donghaiense correlated well with the optical density, and the regression equation is y=4×10-6x+ 0.694 9, in which x is the cell number, and y is the optical density, with r2=0.953 5. These results show that the NPA-SH method has good feasibility in the detection of P. donghaiense. Results of NPA-SH and microscopy are excellent for each sample. The NPA-SH method was a simple way in quantitative detection of P. donghaiense, and the whole process could be finished in about six hours, which provided a new approach in high-throughput sampling and long-term monitoring of P. donghaiense.

  1. Optimizations of spin-exchange relaxation-free magnetometer based on potassium and rubidium hybrid optical pumping.

    Science.gov (United States)

    Fang, Jiancheng; Wang, Tao; Zhang, Hong; Li, Yang; Zou, Sheng

    2014-12-01

    The hybrid optical pumping atomic magnetometers have not realized its theoretical sensitivity, the optimization is critical for optimal performance. The optimizations proposed in this paper are suitable for hybrid optical pumping atomic magnetometer, which contains two alkali species. To optimize the parameters, the dynamic equations of spin evolution with two alkali species were solved, whose steady-state solution is used to optimize the parameters. The demand of the power of the pump beam is large for hybrid optical pumping. Moreover, the sensitivity of the hybrid optical pumping magnetometer increases with the increase of the power density of the pump beam. The density ratio between the two alkali species is especially important for hybrid optical pumping magnetometer. A simple expression for optimizing the density ratio is proposed in this paper, which can help to determine the mole faction of the alkali atoms in fabricating the hybrid cell before the cell is sealed. The spin-exchange rate between the two alkali species is proportional to the saturated density of the alkali vapor, which is highly dependent on the temperature of the cell. Consequently, the sensitivity of the hybrid optical pumping magnetometer is dependent on the temperature of the cell. We proposed the thermal optimization of the hybrid cell for a hybrid optical pumping magnetometer, which can improve the sensitivity especially when the power of the pump beam is low. With these optimizations, a sensitivity of approximately 5 fT/Hz(1/2) is achieved with gradiometer arrangement.

  2. Integrated optical buffers for packet-switched networks

    Science.gov (United States)

    Burmeister, Emily Frances

    Routers form the backbone of the Internet, directing data to the right locations with huge throughput capacity of terabits/second) and very few errors (1 error allowed in 1012 bits). However, as the Internet continues to grow rapidly, so must the capacity of electronic routers, thereby also growing in footprint and power consumption. The energy bill alone has developers looking for an alternate solution. Today's routers can only operate with electrical signals although Internet data is transmitted optically. This requires the data to be converted from the optical domain to the electrical domain and back again. Optical routers have the potential of saving in power by omitting these conversions, but have been held back in part by the lack of a practical optical memory device. This work presents the first integrated optical buffer for next generation optical packet-switched networks. Buffering is required in a router to move packets of data in order to avoid collisions between packets heading to the same destination at the same time. The device presented here uses an InP-based two-by-two switch with a silica waveguide delay to form a recirculating buffer. Packet storage was shown with 98% packet recovery for 5 circulations. Autonomous contention resolution was demonstrated with two buffered channels to show that the technology is a realistic solution for creating multiple element buffers on multiple router ports. This thesis proposes and demonstrates the first integrated optical random access memory, thereby making a great stride toward high capacity optical routers.

  3. Amorphous silicon rich silicon nitride optical waveguides for high density integrated optics

    DEFF Research Database (Denmark)

    Philipp, Hugh T.; Andersen, Karin Nordström; Svendsen, Winnie Edith

    2004-01-01

    Amorphous silicon rich silicon nitride optical waveguides clad in silica are presented as a high-index contrast platform for high density integrated optics. Performance of different cross-sectional geometries have been measured and are presented with regards to bending loss and insertion loss...

  4. Amorphous silicon rich silicon nitride optical waveguides for high density integrated optics

    DEFF Research Database (Denmark)

    Philipp, Hugh T.; Andersen, Karin Nordström; Svendsen, Winnie Edith

    2004-01-01

    Amorphous silicon rich silicon nitride optical waveguides clad in silica are presented as a high-index contrast platform for high density integrated optics. Performance of different cross-sectional geometries have been measured and are presented with regards to bending loss and insertion loss....... A sample double ring add-drop filter is presented....

  5. Hybrid optics for three-dimensional microstructuring of polymers via direct laser writing

    Science.gov (United States)

    Burmeister, Frank; Zeitner, Uwe D.; Nolte, Stefan; Tünnermann, Andreas

    2012-03-01

    We present an immersion hybrid optics specially designed for focusing ultrashort laser pulses into a polymer for direct laser writing via two-photon polymerization. The hybrid optics enables well corrected focusing over a working distance range of 577 μm with a numerical aperture (NA) of 1.33 thereby causing low internal dispersion. We combine the concepts of an aplanatic solid immersion lens (ASIL) for achieving a high NA with the correction of aberrations with a diffractive optical element (DOE). To demonstrate the improvements for volume structuring of the polymer, we compare achievable feature sizes of structures written with our optics and a commercial available oil immersion objective (100x, NA=1.4).

  6. Tunable hybridization at midzone and anomalous Bloch-Zener oscillations in optical waveguide ladders.

    Science.gov (United States)

    Zheng, Ming Jie; Wang, Gang; Yu, Kin Wah

    2010-12-01

    We have studied the optical oscillation and tunneling of light waves in optical waveguide ladders (OWLs) formed by two coupled planar optical waveguide arrays. For the band structure, a midzone gap is formed owing to band hybridization, and its wavenumber position can be tuned throughout the whole Brillouin zone, which is different from the Bragg gap. By imposing a gradient in the propagation constant in each array, Bloch-Zener oscillation (BZO) is realized with Zener tunneling between the bands occurring at the midzone, which is contrary to the common BZO with tunneling at the center or edge of the Brillouin zone. The occurrence of BZO is demonstrated by using the field-evolution analysis. The tunable hybridization at the midzone enhances the tunability of BZO in the OWLs. This Letter may offer new insights into the coherent phenomena in optical lattices.

  7. Nonclassical correlation between optical and microwave photons in a hybrid electro-optomechanical system

    Science.gov (United States)

    Xie, Hong; Chen, Xiang; Lin, Gongwei; Lin, Xiumin

    2016-10-01

    A scheme to correlate optical and microwave photons is proposed in a hybrid electro-optomechanical system, where mechanical resonator is coupled to both optical and microwave fields. Analytical and numerical simulation results show that the cross-correlation function between Stokes and anti-Stokes photons strongly violates the Cauchy-Schwarz inequality, which confirms the nonclassical correlation between the optical and microwave photons. It is worth noting that the nonclassical photon pairs with vast different wavelengths, which may be useful for quantum communication, are generated under the experimentally accessible weak coupling limit rather than single-photon strong coupling regime. In addition, the protocol provides a possible route to combine the respective advantages of optical photons, microwave photons, and phonons in a hybrid electro-optomechanical system.

  8. Mapping coherence in measurement via full quantum tomography of a hybrid optical detector

    CERN Document Server

    Zhang, Lijian; Datta, Animesh; Puentes, Graciana; Lundeen, Jeff S; Jin, Xian-Min; Smith, Brian J; Plenio, Martin B; Walmsley, Ian A

    2012-01-01

    Quantum states and measurements exhibit wave-like --- continuous, or particle-like --- discrete, character. Hybrid discrete-continuous photonic systems are key to investigating fundamental quantum phenomena, generating superpositions of macroscopic states, and form essential resources for quantum-enhanced applications, e.g. entanglement distillation and quantum computation, as well as highly efficient optical telecommunications. Realizing the full potential of these hybrid systems requires quantum-optical measurements sensitive to complementary observables such as field quadrature amplitude and photon number. However, a thorough understanding of the practical performance of an optical detector interpolating between these two regions is absent. Here, we report the implementation of full quantum detector tomography, enabling the characterization of the simultaneous wave and photon-number sensitivities of quantum-optical detectors. This yields the largest parametrization to-date in quantum tomography experiments...

  9. Light waves in thin films and integrated optics.

    Science.gov (United States)

    Tien, P K

    1971-11-01

    Integrated optics is a far-reaching attempt to apply thin-film technology to optical circuits and devices, and, by using methods of integrated circuitry, to achieve a better and more economical optical system. The specific topics discussed here are physics of light waves in thin films, materials and losses involved, methods of couplings light beam into and out of a thin film, and nonlinear interactions in waveguide structures. The purpose of this paper is to review in some detail the important development of this new and fascinating field, and to caution the reader that the technology involved is difficult because of the smallness and perfection demanded by thin-film optical devices.

  10. Optical nanofibre integrated into an optical tweezers for particle manipulation, in situ fibre probing, and optical binding studies

    CERN Document Server

    Gusachenko, Ivan; Frawley, Mary C; Chormaic, Síle Nic

    2015-01-01

    Precise control of particle positioning is desirable in many optical propulsion and sorting applications. Here, we develop an integrated platform for particle manipulation consisting of a combined optical nanofibre and optical tweezers system. Individual silica microspheres were introduced to the nanofibre at arbitrary points using the optical tweezers, thereby producing pronounced dips in the fibre transmission. We show that such consistent and reversible transmission modulations depend on both particle and fibre diameter, and can be used as a reference point for in situ nanofibre or particle size measurement. Thence, we combine scanning electron microscope (SEM) size measurements with nanofibre transmission data to provide calibration for particle-based fibre assessment. This integrated optical platform provides a method for selective evanescent field manipulation of micron-sized particles and facilitates studies of optical binding and light-particle interaction dynamics.

  11. 100-Gbps hybrid optical fiber-wireless transmission

    DEFF Research Database (Denmark)

    Pang, Xiaodan; Caballero Jambrina, Antonio; Deng, Lei;

    2013-01-01

    We present experimental results on using optical transmission technologies such as I&Q modulators, digital coherent receivers, heterodyne up-conversion in fast photodiodes, to generate, transmit and detect high capacity wireless transmission. Both OFDM and QAM modulation formats are tested in the......-achieving capacities up to 100-Gbps with seamless optical fiber-wireless conversion.......We present experimental results on using optical transmission technologies such as I&Q modulators, digital coherent receivers, heterodyne up-conversion in fast photodiodes, to generate, transmit and detect high capacity wireless transmission. Both OFDM and QAM modulation formats are tested in the W...

  12. Viral Hybrid Vectors for Somatic Integration - Are They the Better Solution?

    Directory of Open Access Journals (Sweden)

    Anja Ehrhardt

    2009-12-01

    Full Text Available The turbulent history of clinical trials in viral gene therapy has taught us important lessons about vector design and safety issues. Much effort was spent on analyzing genotoxicity after somatic integration of therapeutic DNA into the host genome. Based on these findings major improvements in vector design including the development of viral hybrid vectors for somatic integration have been achieved. This review provides a state-of-the-art overview of available hybrid vectors utilizing viruses for high transduction efficiencies in concert with various integration machineries for random and targeted integration patterns. It discusses advantages but also limitations of each vector system.

  13. Development of a Hybrid Nanoprobe for Triple-Modality MR/SPECT/Optical Fluorescence Imaging

    Science.gov (United States)

    Madru, Renata; Svenmarker, Pontus; Ingvar, Christian; Ståhlberg, Freddy; Engels, Stefan-Andersson; Knutsson, Linda; Strand, Sven-Erik

    2014-01-01

    Hybrid clinical imaging is an emerging technology, which improves disease diagnosis by combining already existing technologies. With the combination of high-resolution morphological imaging, i.e., MRI/CT, and high-sensitive molecular detection offered by SPECT/PET/Optical, physicians can detect disease progression at an early stage and design patient-specific treatments. To fully exploit the possibilities of hybrid imaging a hybrid probe compatible with each imaging technology is required. Here, we present a hybrid nanoprobe for triple modality MR/SPECT/Fluorescence imaging. Our imaging agent is comprised of superparamagnetic iron oxide nanoparticles (SPIONs), labeled with 99mTc and an Alexa fluorophore (AF), together forming 99mTc-AF-SPIONs. The agent was stable in human serum, and, after subcutaneous injection in the hind paw of Wistar rats, showed to be highly specific by accumulating in the sentinel lymph node. All three modalities clearly visualized the imaging agent. Our results show that a single imaging agent can be used for hybrid imaging. The use of a single hybrid contrast agent permits simultaneous hybrid imaging and, more conventionally, allow for single modality imaging at different time points. For example, a hybrid contrast agent enables pre-operative planning, intra-operative guidance, and post-operative evaluation with the same contrast agent. PMID:26852675

  14. Effective-mass model and magneto-optical properties in hybrid perovskites

    OpenAIRE

    Yu, Z. G.

    2016-01-01

    Hybrid inorganic-organic perovskites have proven to be a revolutionary material for low-cost photovoltaic applications. They also exhibit many other interesting properties, including giant Rashba splitting, large-radius Wannier excitons, and novel magneto-optical effects. Understanding these properties as well as the detailed mechanism of photovoltaics requires a reliable and accessible electronic structure, on which models of transport, excitonic, and magneto-optical properties can be effici...

  15. An Integrated Optical Memory based on Laser Written Waveguides

    CERN Document Server

    Corrielli, Giacomo; Mazzera, Margherita; Osellame, Roberto; de Riedmatten, Hugues

    2016-01-01

    We report on the first realization of an integrated optical memory for light based on a laser written waveguide in a doped crystal. Using femto-second laser micromachining, we fabricate waveguides in Pr$^{3+}$:Y$_2$SiO$_5$ crystal. We demonstrate that the waveguide inscription does not affect the coherence properties of the material and that the light confinement in the waveguide increases the interaction with the active ions by a factor 6. We also demonstrate that, analogously to the bulk crystals, we can operate the optical pumping protocols necessary to prepare the population in atomic frequency combs, that we use to demonstrate light storage in excited and spin states of the Praseodymium ions. Our results represent the first realization of laser written waveguides in a Pr$^{3+}$:Y$_2$SiO$_5$ crystal and the first implementation of an integrated on-demand spin wave optical memory. They open new perspectives for integrated quantum memories.

  16. Streamline Integration using MPI-Hybrid Parallelism on a Large Multi-Core Architecture

    Energy Technology Data Exchange (ETDEWEB)

    Camp, David; Garth, Christoph; Childs, Hank; Pugmire, Dave; Joy, Kenneth I.

    2010-11-01

    Streamline computation in a very large vector field data set represents a significant challenge due to the non-local and datadependentnature of streamline integration. In this paper, we conduct a study of the performance characteristics of hybrid parallel programmingand execution as applied to streamline integration on a large, multicore platform. With multi-core processors now prevalent in clustersand supercomputers, there is a need to understand the impact of these hybrid systems in order to make the best implementation choice.We use two MPI-based distribution approaches based on established parallelization paradigms, parallelize-over-seeds and parallelize-overblocks,and present a novel MPI-hybrid algorithm for each approach to compute streamlines. Our findings indicate that the work sharing betweencores in the proposed MPI-hybrid parallel implementation results in much improved performance and consumes less communication andI/O bandwidth than a traditional, non-hybrid distributed implementation.

  17. Integrated optical measurement system for fluorescence spectroscopy in microfluidic channels

    DEFF Research Database (Denmark)

    Hübner, Jörg; Mogensen, Klaus Bo; Jørgensen, Anders Michael

    2001-01-01

    A transportable miniaturized fiber-pigtailed measurement system is presented which allows quantitative fluorescence detection in microliquid handling systems. The microliquid handling chips are made in silica on silicon technology and the optical functionality is monolithically integrated...... with the microfluidic channel system. This results in inherent stability and photolithographic alignment precision. Permanently attached optical fibers provide a rugged connection to the light source, detection, and data processing unit, which potentially allows field use of such systems. Fluorescence measurements...

  18. Hybrid integration of III-V semiconductor lasers on silicon waveguides using optofluidic microbubble manipulation

    Science.gov (United States)

    Jung, Youngho; Shim, Jaeho; Kwon, Kyungmook; You, Jong-Bum; Choi, Kyunghan; Yu, Kyoungsik

    2016-07-01

    Optofluidic manipulation mechanisms have been successfully applied to micro/nano-scale assembly and handling applications in biophysics, electronics, and photonics. Here, we extend the laser-based optofluidic microbubble manipulation technique to achieve hybrid integration of compound semiconductor microdisk lasers on the silicon photonic circuit platform. The microscale compound semiconductor block trapped on the microbubble surface can be precisely assembled on a desired position using photothermocapillary convective flows induced by focused laser beam illumination. Strong light absorption within the micro-scale compound semiconductor object allows real-time and on-demand microbubble generation. After the assembly process, we verify that electromagnetic radiation from the optically-pumped InGaAsP microdisk laser can be efficiently coupled to the single-mode silicon waveguide through vertical evanescent coupling. Our simple and accurate microbubble-based manipulation technique may provide a new pathway for realizing high precision fluidic assembly schemes for heterogeneously integrated photonic/electronic platforms as well as microelectromechanical systems.

  19. Potential for integrated optical circuits in advanced aircraft with fiber optic control and monitoring systems

    Science.gov (United States)

    Baumbick, Robert

    1991-01-01

    The current Fiber Optic Control System Integration (FOCSI) program is reviewed and the potential role of IOCs in FOCSI applications is described. The program is intended for building, environmentally testing, and demonstrating operation in piggyback flight tests (no active control with optical sensors) of a representative sensor system for propulsion and flight control. The optical sensor systems are to be designed to fit alongside the bill-of-materials sensors for comparison. The sensors are to be connected to electrooptic architecture cards which will contain the optical sources and detectors to recover and process the modulated optical signals. The FOCSI program is to collect data on the behavior of passive optical sensor systems in a flight environment and provide valuable information on installation amd maintenance problems for this technology, as well as component survivability (light sources, connectors, optical fibers, etc.).

  20. Hybrid optical and electronic laser locking using spectral hole burning

    CERN Document Server

    Farr, Warrick G; Ledingham, Patrick M; Korystov, Dmitry; Longdell, Jevon J

    2010-01-01

    We report on a narrow linewidth laser diode system that is stabilized using both optical and electronic feedback to a spectral hole in cryogenic Tm:YAG. The laser system exhibits very low phase noise. The spectrum of the beat signal between two lasers, over millisecond timescales, is either Fourier limited or limited by the -111dBc/Hz noise floor. The resulting laser is well suited to quantum optics and sensing applications involving rare earth ion dopants.

  1. 40 GHz electro-optic modulation in hybrid silicon-organic slotted photonic crystal waveguides.

    Science.gov (United States)

    Wülbern, Jan Hendrik; Prorok, Stefan; Hampe, Jan; Petrov, Alexander; Eich, Manfred; Luo, Jingdong; Jen, Alex K-Y; Jenett, Martin; Jacob, Arne

    2010-08-15

    In this Letter we demonstrate broadband electro-optic modulation with frequencies of up to 40 GHz in slotted photonic crystal waveguides based on silicon-on-insulator substrates covered and infiltrated with a nonlinear optical polymer. Two-dimensional photonic crystal waveguides in silicon enable integrated optical devices with an extremely small geometric footprint on the scale of micrometers. The slotted waveguide design optimizes the overlap of the optical and electric fields in the second-order nonlinear optical medium and, hence, the interaction of the optical and electric waves.

  2. Integrated structural and functional optical imaging combining spectral-domain optical coherence and multiphoton microscopy

    CERN Document Server

    Vinegoni, C; Luo, W; Marks, D L; Ralston, T; Tan, W

    2005-01-01

    An integrated microscope that combines different optical techniques for simultaneous imaging is demonstrated. The microscope enables spectral-domain optical coherence microscopy based on optical backscatter, and multi-photon microscopy for the detection of two-photon fluorescence and second harmonic generation signals. The unique configuration of this integrated microscope allows for the simultaneous acquisition of both anatomical (structural) and functional imaging information with particular emphasis for applications in the fields of tissue engineering and cell biology. In addition, the contemporary analysis of the spectroscopic features can enhance contrast by differentiating among different tissue components.

  3. Resilience of hybrid optical angular momentum qubits to turbulence.

    Science.gov (United States)

    Farías, Osvaldo Jiménez; D'Ambrosio, Vincenzo; Taballione, Caterina; Bisesto, Fabrizio; Slussarenko, Sergei; Aolita, Leandro; Marrucci, Lorenzo; Walborn, Stephen P; Sciarrino, Fabio

    2015-02-12

    Recent schemes to encode quantum information into the total angular momentum of light, defining rotation-invariant hybrid qubits composed of the polarization and orbital angular momentum degrees of freedom, present interesting applications for quantum information technology. However, there remains the question as to how detrimental effects such as random spatial perturbations affect these encodings. Here, we demonstrate that alignment-free quantum communication through a turbulent channel based on hybrid qubits can be achieved with unit transmission fidelity. In our experiment, alignment-free qubits are produced with q-plates and sent through a homemade turbulence chamber. The decoding procedure, also realized with q-plates, relies on both degrees of freedom and renders an intrinsic error-filtering mechanism that maps errors into losses.

  4. Photonic Integrated Devices for Nonlinear Optics

    CERN Document Server

    Caspani, Lucia; Dolgaleva, Ksenia; Wagner, Sean; Ferrera, Marcello; Razzari, Luca; Pasquazi, Alessia; Peccianti, Marco; Moss, David J; Aitchison, J Stewart; Morandotti, Roberto

    2014-01-01

    We review our recent progresses on frequency conversion in integrated devices, focusing primarily on experiments based on strip-loaded and quantum-well intermixed AlGaAs waveguides, and on CMOS-compatible high-index doped silica glass waveguides. The former includes both second- and third-order interactions, demonstrating wavelength conversion by tunable difference-frequency generation over a bandwidth of more than nm, as well as broadband self-phase modulation and tunable four-wave mixing. The latter includes four-wave mixing using low-power continuous-wave light in microring resonators as well as hyper-parametric oscillation in a high quality factor resonator, towards the realization of an integrated multiple wavelength source with important applications for telecommunications, spectroscopy, and metrology.

  5. Integrated semiconductor twin-microdisk laser under mutually optical injection

    Energy Technology Data Exchange (ETDEWEB)

    Zou, Ling-Xiu; Liu, Bo-Wen; Lv, Xiao-Meng; Yang, Yue-De; Xiao, Jin-Long; Huang, Yong-Zhen, E-mail: yzhuang@semi.ac.cn [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China)

    2015-05-11

    We experimentally study the characteristics of an integrated semiconductor twin-microdisk laser under mutually optical injection through a connected optical waveguide. Based on the lasing spectra, four-wave mixing, injection locking, and period-two oscillation states are observed due to the mutually optical injection by adjusting the injected currents applied to the two microdisks. The enhanced 3 dB bandwidth is realized for the microdisk laser at the injection locking state, and photonic microwave is obtained from the electrode of the microdisk laser under the period-two oscillation state. The plentifully dynamical states similar as semiconductor lasers subject to external optical injection are realized due to strong optical interaction between the two microdisks.

  6. Compact optical integration instrument to measure intraocular straylight.

    Science.gov (United States)

    Ginis, Harilaos; Sahin, Onurcan; Pennos, Alexandros; Artal, Pablo

    2014-09-01

    Optical measurement of straylight in the human eye is a challenging task. Issues such as illumination geometry, detector sensitivity and dynamic range as well as various inherent artifacts must be addressed. We developed a novel instrument based on the principle of double-pass optical integration adapted for fast measurements in a clinical setting. The experimental setup was validated using four different diffusers introduced in front of the eyes of ten subjects. Measurement limitations and future implications of rapid optical measurement of straylight in ophthalmic diagnosis are discussed.

  7. Collimating Slicer for Optical Integral Field Spectroscopy

    CERN Document Server

    Laurent, Florence

    2016-01-01

    Integral Field Spectroscopy (IFS) is a technique that gives simultaneously the spectrum of each spatial sampling element in a given object field. It is a powerful tool which rearranges the data cube (x, y, lambda) represented by two spatial dimensions defining the field and the spectral decomposition in a detector plane. In IFS, the spatial unit reorganizes the field and the spectral unit is being composed of a classical spectrograph.The development of a Collimating Slicer aims at proposing a new type of integral field spectrograph which should be more compact. The main idea is to combine the image slicer with the collimator of the spectrograph, thus mixing the spatial and spectral units. The traditional combination of slicer, pupil and slit elements and the spectrograph collimator is replaced by a new one composed of a slicer and collimator only. In this paper, the state of the art of integral field spectroscopy using image slicers is described. The new system based onto the development of a Collimating Slic...

  8. Stabilization and frequency control of a DFB laser with a tunable optical reflector integrated in a Silicon Photonics PIC

    CERN Document Server

    Hauck, Johannes; Romero-García, Sebastían; Müller, Juliana; Shen, Bin; Richter, Jens; Merget, Florian; Witzens, Jeremy

    2016-01-01

    We investigate the effect of tunable optical feedback on a commercial DFB laser edge coupled to a Silicon Photonics planar integrated circuit in which a tunable reflector has been implemented by means of a ring resonator based add-drop multiplexer. Controlled optical feedback allows for fine-tuning of the laser oscillation frequency. Under certain conditions it also allows suppression of bifurcation modes triggered by reflections occurring elsewhere on the chip. A semi-analytical model describing laser dynamics under combined optical feedback from the input facet of the edge coupler and from the tunable on-chip reflector fits the measurements. Compensation of detrimental effects from reflections induced elsewhere on a transceiver chip may allow moving isolators downstream in future communications systems, facilitating direct hybrid laser integration in Silicon Photonics chips, provided a suitable feedback signal for a control system can be identified. Moreover, the optical frequency tuning at lower feedback l...

  9. Integrated Micro-Optical Fluorescence Detection System for Microfluidic Electrochromatography

    Energy Technology Data Exchange (ETDEWEB)

    ALLERMAN,ANDREW A.; ARNOLD,DON W.; ASBILL,RANDOLPH E.; BAILEY,CHRISTOPHER G.; CARTER,TONY RAY; KEMME,SHANALYN A.; MATZKE,CAROLYN M.; SAMORA,SALLY; SWEATT,WILLIAM C.; WARREN,MIAL E.; WENDT,JOEL R.

    1999-09-16

    The authors describe the design and microfabrication of an extremely compact optical system as a key element in an integrated capillary-channel electrochromatograph with laser induced fluorescence detection. The optical design uses substrate-mode propagation within the fused silica substrate. The optical system includes a vertical cavity surface-emitting laser (VCSEL) array, two high performance microlenses and a commercial photodetector. The microlenses are multilevel diffractive optics patterned by electron beam lithography and etched by reactive ion etching in fused silica. Two generations of optical subsystems are described. The first generation design is integrated directly onto the capillary channel-containing substrate with a 6 mm separation between the VCSEL and photodetector. The second generation design separates the optical system onto its own module and the source to detector length is further compressed to 3.5 mm. The systems are designed for indirect fluorescence detection using infrared dyes. The first generation design has been tested with a 750 nm VCSEL exciting a 10{sup -4} M solution of CY-7 dye. The observed signal-to-noise ratio of better than 100:1 demonstrates that the background signal from scattered pump light is low despite the compact size of the optical system and meets the system sensitivity requirements.

  10. Hybrid function method for solving Fredholm and Volterra integral equations of the second kind

    Science.gov (United States)

    Hsiao, Chun-Hui

    2009-08-01

    Numerical solutions of Fredholm and Volterra integral equations of the second kind via hybrid functions, are proposed in this paper. Based upon some useful properties of hybrid functions, integration of the cross product, a special product matrix and a related coefficient matrix with optimal order, are applied to solve these integral equations. The main characteristic of this technique is to convert an integral equation into an algebraic; hence, the solution procedures are either reduced or simplified accordingly. The advantages of hybrid functions are that the values of n and m are adjustable as well as being able to yield more accurate numerical solutions than the piecewise constant orthogonal function, for the solutions of integral equations. We propose that the available optimal values of n and m can minimize the relative errors of the numerical solutions. The high accuracy and the wide applicability of the hybrid function approach will be demonstrated with numerical examples. The hybrid function method is superior to other piecewise constant orthogonal functions [W.F. Blyth, R.L. May, P. Widyaningsih, Volterra integral equations solved in Fredholm form using Walsh functions, Anziam J. 45 (E) (2004) C269-C282; M.H. Reihani, Z. Abadi, Rationalized Haar functions method for solving Fredholm and Volterra integral equations, J. Comp. Appl. Math. 200 (2007) 12-20] for these problems.

  11. Hybrid optical-digital encryption system based on wavefront coding paradigm

    Science.gov (United States)

    Konnik, Mikhail V.

    2012-04-01

    The wavefront coding is a widely used in the optical systems to compensate aberrations and increase the depth of field. This paper presents experimental results on application of the wavefront coding paradigm for data encryption. We use a synthesised diffractive optical element (DOE) to deliberately introduce a phase distortion during the images registration process to encode the acquired image. In this case, an optical convolution of the input image with the point spread function (PSF) of the DOE is registered. The encryption is performed optically, and is therefore is fast and secure. Since the introduced distortion is the same across the image, the decryption is performed digitally using deconvolution methods. However, due to noise and finite accuracy of a photosensor, the reconstructed image is degraded but still readable. The experimental results, which are presented in this paper, indicate that the proposed hybrid optical-digital system can be implemented as a portable device using inexpensive off-the-shelf components. We present the results of optical encryption and digital restoration with quantitative estimations of the images quality. Details of hardware optical implementation of the hybrid optical-digital encryption system are discussed.

  12. Field weighting model for tracking-integrated optics

    Science.gov (United States)

    Wheelwright, Brian; Angel, Roger; Coughenour, Blake; Hammer, Kimberly; Geary, Andrew; Stalcup, Thomas

    2014-09-01

    The emergent field of tracking-integrated optics enables a potentially low cost concentrating photovoltaic (CPV) implementation, where single-axis module tracking is complemented by an additional degree of freedom within the module [1,2,3,4,5]. Gross module tracking can take on multiple configurations, the most common being rotation about a polar or horizontal North-South oriented axis. Polar-axis tracking achieves >95% sunlight collection compared to dual-axis tracking[6], leaving the tracking-integrated optics to compensate for +/-23.5° seasonal variations. The collection efficiency of N-S horizontal axis tracking is latitude-dependent, with ˜90% collection relative to dual-axis tracking at 32.2° latitude. Horizontal tracking at higher latitudes shifts an increasing burden to the tracking-integrated optics, which must operate between two incidence angle extremes: summer solstice sunrise/sunset to winter solstice noon. An important aspect of tracking-integrated lens design is choosing a suitable field weighting to appropriately account for annual DNI received at each angle of incidence. We present a field weighting model, generalized for polar or horizontal module tracking at any latitude, which shows excellent agreement with measured insolation data. This model is particularly helpful for the design of tracking-integrated optics for horizontally-tracked modules, where the correct field weighting is asymmetric and significantly biased away from the normal incidence.

  13. Simulation of integrated optical network (IPON) properties

    Science.gov (United States)

    Siska, Petr; Koudelka, Petr; Latal, Jan; Vitasek, Jan; Kepak, Stanislav; Vašinek, Vladimír.

    2014-09-01

    There is an increasing pressure nowadays on the efficient use of existing ICT infrastructure in order to provide the latest services for corporate customers or end users. With the increase in number of services, requirements for optical networks of all hierarchies are increasing as well. This increase in the requirements, however, involves risks which must be faced by Internet service providers. These include the maximum use of spectral range, bandwidth and reachable distance, suppression of dispersion effect, route planning efficiency, CAPEX and OPEX costs management, or successful combination of technologies of deployed networks. The aim of this article is to present the problems associated with interconnection of WDM-PON and ver.2 EPON (IEEE 802.3ah standard). The entire simulation is based on real parameters, which were provided by the manufacturers of the technologies and then measured in the laboratory. Then we were able to perform simulations based on more realistic features of these technologies.

  14. Optically envelope detected QAM and QPSK RF modulated signals in hybrid wireless-fiber systems

    DEFF Research Database (Denmark)

    Tafur Monroy, Idelfonso; Prince, Kamau; Seoane, Jorge;

    2009-01-01

    from a 1.6 GHz carrier frequency to an IF at 500 MHz, requiring no high frequency local oscillator and mixer at the remote base station. This result proves the feasibility of optical envelope detection for complex modulation formats of RF signals for hybrid wireless-fiber transmission links....

  15. Continuous-wave Optically Pumped Lasing of Hybrid Perovskite VCSEL at Green Wavelength

    KAUST Repository

    Alias, Mohd Sharizal

    2017-05-08

    We demonstrate the lasing of a perovskite vertical-cavity surface-emitting laser at green wavelengths, which operates under continuous-wave optical pumping at room-temperature by embedding hybrid perovskite between dielectric mirrors deposited at low-temperature.

  16. Hybrid RF/Optical Communications via 34-meter DSN Antennas

    Science.gov (United States)

    Vilnrotter, V.

    2010-02-01

    There is considerable interest in determining whether suitably modified versions of existing 34-m antennas at NASA's Goldstone Communications Complex, originally designed for X-band (nominally 8 GHz) and Ka-band (32 GHz) operation, could also be used to receive near-infrared optical signals. The robust backup structure of these antennas, together with extremely large collecting apertures and millidegree pointing capabilities, suggest that dual RF/optical communications may indeed be possible, at optical data rates approaching 1 gigabit per second (GBPS) from typical Mars distances. Several design concepts have emerged as possible candidates, requiring modifications ranging from polishing and coating of the existing aluminum panels of the main reflector, to significant redesign involving replacement of the panels with optical reflectors. Optical receiver parameters such as collecting area, field of view (FOV), and immunity to reflected sunlight differ markedly for each design concept, hence will likely lead to different levels of performance in terms of data throughput at a given error probability, and in terms of the ability to point close to the Sun. The communications performance of two candidate design concepts operating under realistic daytime conditions is evaluated, with particular emphasis on spatial and temporal acquisition algorithms and receiver optimization to achieve the best possible communication performance at high data rates.

  17. Integrated optical Dirac physics via inversion symmetry breaking

    Science.gov (United States)

    Collins, Matthew J.; Zhang, Fan; Bojko, Richard; Chrostowski, Lukas; Rechtsman, Mikael C.

    2016-12-01

    Graphene and boron nitride are two-dimensional materials whose atoms are arranged in a honeycomb lattice. Their unique properties arise because their electrons behave like relativistic particles (without and with mass, respectively)—namely, they obey the Dirac equation. Here, we use a photonic analog of boron nitride to observe Dirac physics in a silicon integrated optical platform. This will allow for photonic applications of Dirac dispersions (gapped and ungapped) to be realized in an on-chip, integrated nanophotonic platform.

  18. A gold hybrid structure as optical coupler for quantum well infrared photodetector

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Jiayi; Li, Qian; Jing, Youliang [National Laboratory for Infrared Physics, Shanghai Institute of Technical Physics, Chinese Academy of Sciences, 500 Yu Tian Road, Shanghai 200083 (China); Chen, Xiaoshuang, E-mail: xschen@mail.sitp.ac.cn; Li, Zhifeng; Li, Ning; Lu, Wei [National Laboratory for Infrared Physics, Shanghai Institute of Technical Physics, Chinese Academy of Sciences, 500 Yu Tian Road, Shanghai 200083 (China); Synergetic Innovation Center of Quantum Information and Quantum Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China)

    2014-08-28

    A hybrid structure consisting of a square lattice of gold disk arrays and an overlaying gold film is proposed as an optical coupler for a backside-illuminated quantum well infrared photodetector (QWIP). Finite difference time-domain method is used to numerically simulate the reflection spectra and the field distributions of the hybrid structure combined with the QWIP device. The results show that the electric field component perpendicular to the quantum well is strongly enhanced when the plasmonic resonant wavelength of the hybrid structure coincides with the response one of the quantum well infrared photodetector regardless of the polarization of the incident light. The effect of the diameter and thickness of an individual gold disk on the resonant wavelength is also investigated, which indicates that the localized surface plasmon also plays a role in the light coupling with the hybrid structure. The coupling efficiency can exceed 50 if the structural parameters of the gold disk arrays are well optimized.

  19. PDM-DPSK-MPPM hybrid modulation for multi-hop free-space optical communication

    Science.gov (United States)

    Wang, Zhuo; Shi, Wen-xiao; Wu, Peng-xia

    2016-11-01

    A hybrid polarization division multiplexed-differential phase shift keying-multipulse pulse position modulation (PDM-DPSK-MPPM) scheme for multi-hop free-space optical (FSO) communication is investigated. The analytical bit error rate ( BER) of the proposed system in Gamma-Gamma turbulence channels is derived and verified using computer simulation. The results show that both multi-hop and hybrid modulation schemes are efficient techniques to improve the performance of FSO links. Compared with the traditional binary phase shift keying (BPSK) and MPPM, the hybrid scheme can improve the bandwidth-utilization efficiency and reliability of the system. Compared with the coherent demodulation of PDM-QPSK-MPPM, the system complexity is reduced at the cost of the degradation of BER performance, which can improve the practicality of hybrid modulation technology in FSO system.

  20. GHz bandwidth noise eater hybrid optical amplifier: design guidelines.

    Science.gov (United States)

    Danion, Gwennaël; Bondu, François; Loas, Goulc'hen; Alouini, Mehdi

    2014-07-15

    This Letter describes the design of an optical amplifier system optimized to reduce the relative intensity noise (RIN) of the input signal, and discloses its performance in terms of intensity noise reduction and bandwidth, without phase noise degradation. This polarization-maintaining amplifier is composed of an erbium-doped fiber amplifier (EDFA) cascaded with a semiconductor optical amplifier (SOA). The EDFA is sized to feed the SOA with a constant power corresponding to the optimal saturation level for noise reduction, through coherent population oscillations. When properly optimized, such an amplifier provides, simultaneously, 17 dB optical gain, 5.4 dB noise factor, and 20 dB reduction of the input-RIN across a 3 GHz bandwidth, without any electronics feedback loop.

  1. Numerical investigation of optical Tamm states in two-dimensional hybrid plasmonic-photonic crystal nanobeams

    Science.gov (United States)

    Meng, Zi-Ming; Hu, Yi-Hua; Ju, Gui-Fang; Zhong, Xiao-Lan; Ding, Wei; Li, Zhi-Yuan

    2014-07-01

    Optical Tamm states (OTSs) in analogy with its electronic counterpart confined at the surface of crystals are optical surface modes at the interfaces between uniform metallic films and distributed Bragg reflectors. In this paper, OTSs are numerically investigated in two-dimensional hybrid plasmonic-photonic crystal nanobeams (HPPCN), which are constructed by inserting a metallic nanoparticle into a photonic crystal nanobeam formed by periodically etching square air holes into dielectric waveguides. The evidences of OTSs can be verified by transmission spectra and the field distribution at resonant frequency. Similar to OTSs in one-dimensional multilayer structures OTSs in HPPCN can be excited by both TE and TM polarization. The physical origin of OTSs in HPPCN is due to the combined contribution of strong reflection imposed by the photonic band gap (PBG) of the photonic crystal (PC) nanobeam and strong backward scattering exerted by the nanoparticle. For TE, incidence OTSs can be obtained at the frequency near the center of the photonic band gap. The transmissivity and the resonant frequency can be finely tuned by the dimension of nanoparticles. While for TM incidence OTSs are observed for relatively larger metallic nanoparticles compared with TE polarization. The differences between TE and TM polarization can be explained by two reasons. For one reason stronger backward scattering of nanoparticles for TE polarization can be achieved by the excitation of localized surface plasmon polariton of nanoparticles. This assumption has been proved by examining the scattering, absorption, and extinction cross section of the metallic nanoparticle. The other can be attributed to the deep and wide PBG available for TE polarization with less number of air holes compared with TM polarization. Our results show great promise in extending the application scope of OTSs from one-dimensional structures to practical integrated photonic devices and circuits.

  2. Numerical investigation of optical Tamm states in two-dimensional hybrid plasmonic-photonic crystal nanobeams

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Zi-Ming, E-mail: mengzm@gdut.edu.cn, E-mail: lizy@aphy.iphy.ac.cn; Hu, Yi-Hua; Ju, Gui-Fang [School of Physics and Optoelectronic Engineering, Guangdong University of Technology, Guangzhou 510006 (China); Zhong, Xiao-Lan; Ding, Wei; Li, Zhi-Yuan, E-mail: mengzm@gdut.edu.cn, E-mail: lizy@aphy.iphy.ac.cn [Laboratory of Optical Physics, Institute of Physics, Chinese Academy of Sciences, P.O. Box 603, Beijing 100190 (China)

    2014-07-28

    Optical Tamm states (OTSs) in analogy with its electronic counterpart confined at the surface of crystals are optical surface modes at the interfaces between uniform metallic films and distributed Bragg reflectors. In this paper, OTSs are numerically investigated in two-dimensional hybrid plasmonic-photonic crystal nanobeams (HPPCN), which are constructed by inserting a metallic nanoparticle into a photonic crystal nanobeam formed by periodically etching square air holes into dielectric waveguides. The evidences of OTSs can be verified by transmission spectra and the field distribution at resonant frequency. Similar to OTSs in one-dimensional multilayer structures OTSs in HPPCN can be excited by both TE and TM polarization. The physical origin of OTSs in HPPCN is due to the combined contribution of strong reflection imposed by the photonic band gap (PBG) of the photonic crystal (PC) nanobeam and strong backward scattering exerted by the nanoparticle. For TE, incidence OTSs can be obtained at the frequency near the center of the photonic band gap. The transmissivity and the resonant frequency can be finely tuned by the dimension of nanoparticles. While for TM incidence OTSs are observed for relatively larger metallic nanoparticles compared with TE polarization. The differences between TE and TM polarization can be explained by two reasons. For one reason stronger backward scattering of nanoparticles for TE polarization can be achieved by the excitation of localized surface plasmon polariton of nanoparticles. This assumption has been proved by examining the scattering, absorption, and extinction cross section of the metallic nanoparticle. The other can be attributed to the deep and wide PBG available for TE polarization with less number of air holes compared with TM polarization. Our results show great promise in extending the application scope of OTSs from one-dimensional structures to practical integrated photonic devices and circuits.

  3. Prediction of metallic nano-optical trapping forces by finite element-boundary integral method.

    Science.gov (United States)

    Pan, Xiao-Min; Xu, Kai-Jiang; Yang, Ming-Lin; Sheng, Xin-Qing

    2015-03-01

    The hybrid of finite element and boundary integral (FE-BI) method is employed to predict nano-optical trapping forces of arbitrarily shaped metallic nanostructures. A preconditioning strategy is proposed to improve the convergence of the iterative solution. Skeletonization is employed to speed up the design and optimization where iteration has to be repeated for each beam configuration. The radiation pressure force (RPF) is computed by vector flux of the Maxwell's stress tensor. Numerical simulations are performed to validate the developed method in analyzing the plasmonic effects as well as the optical trapping forces. It is shown that the proposed method is capable of predicting the trapping forces of complex metallic nanostructures accurately and efficiently.

  4. Advanced hybrid and electric vehicles system optimization and vehicle integration

    CERN Document Server

    2016-01-01

    This contributed volume contains the results of the research program “Agreement for Hybrid and Electric Vehicles”, funded by the International Energy Agency. The topical focus lies on technology options for the system optimization of hybrid and electric vehicle components and drive train configurations which enhance the energy efficiency of the vehicle. The approach to the topic is genuinely interdisciplinary, covering insights from fields. The target audience primarily comprises researchers and industry experts in the field of automotive engineering, but the book may also be beneficial for graduate students.

  5. Low voltage integrated optics electro-optical modulator applied to optical voltage transformer based on WLI technique

    Science.gov (United States)

    Santos, J. C.; Rubini, J.; Silva, L. P. C.; Caetano, R. E.

    2015-09-01

    The use of two electro-optical modulators linked in series, one for sensing and one for recovering signals, was formerly presented by some of the authors as a solution for interrogation of optical fiber sensor systems based on WLI method. A key feature required from such systems is that half-wave voltage (Vπ) of recovering modulator must be as small as possible. Aiming at meeting this requirement, in this paper it is presented the use of an unbalanced Michelson Interferometer implemented using an integrated optics component as recover interferometer in an optical voltage transformer intended for high voltage measurements.

  6. Systematic calibration of an integrated x-ray and optical tomography system for preclinical radiation research

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Yidong, E-mail: yidongyang@med.miami.edu [Department of Radiation Oncology and Molecular Radiation Sciences, Johns Hopkins University School of Medicine, Baltimore, Maryland 21231 and Department of Radiation Oncology, University of Miami School of Medicine, Miami, Florida 33136 (United States); Wang, Ken Kang-Hsin; Wong, John W. [Department of Radiation Oncology and Molecular Radiation Sciences, Johns Hopkins University School of Medicine, Baltimore, Maryland 21231 (United States); Eslami, Sohrab; Iordachita, Iulian I. [Laboratory for Computational Sensing and Robotics, Johns Hopkins University, Baltimore, Maryland 21218 (United States); Patterson, Michael S. [Juravinski Cancer Centre and Department of Medical Physics and Applied Radiation Sciences, McMaster University, Hamilton, Ontario L8S4K1 (Canada)

    2015-04-15

    .0% difference between simulated and measured signal. The calibration of the entire system was confirmed through the CBCT and BLT reconstruction of a bioluminescence source placed inside a tissue-simulating optical phantom. Using a spatial region constraint, the source position was reconstructed with less than 1 mm error and the source strength reconstructed with less than 24% error. Conclusions: A practical and systematic method has been developed to calibrate an integrated x-ray and optical tomography imaging system, including the respective CBCT and optical tomography system calibration and the geometrical calibration of the entire system. The method can be modified and adopted to calibrate CBCT and optical tomography systems that are operated independently or hybrid x-ray and optical tomography imaging systems.

  7. A hybrid approach to device integration on a genetic analysis platform

    Science.gov (United States)

    Brennan, Des; Jary, Dorothee; Kurg, Ants; Berik, Evgeny; Justice, John; Aherne, Margaret; Macek, Milan; Galvin, Paul

    2012-10-01

    Point-of-care (POC) systems require significant component integration to implement biochemical protocols associated with molecular diagnostic assays. Hybrid platforms where discrete components are combined in a single platform are a suitable approach to integration, where combining multiple device fabrication steps on a single substrate is not possible due to incompatible or costly fabrication steps. We integrate three devices each with a specific system functionality: (i) a silicon electro-wetting-on-dielectric (EWOD) device to move and mix sample and reagent droplets in an oil phase, (ii) a polymer microfluidic chip containing channels and reservoirs and (iii) an aqueous phase glass microarray for fluorescence microarray hybridization detection. The EWOD device offers the possibility of fully integrating on-chip sample preparation using nanolitre sample and reagent volumes. A key challenge is sample transfer from the oil phase EWOD device to the aqueous phase microarray for hybridization detection. The EWOD device, waveguide performance and functionality are maintained during the integration process. An on-chip biochemical protocol for arrayed primer extension (APEX) was implemented for single nucleotide polymorphism (SNiP) analysis. The prepared sample is aspirated from the EWOD oil phase to the aqueous phase microarray for hybridization. A bench-top instrumentation system was also developed around the integrated platform to drive the EWOD electrodes, implement APEX sample heating and image the microarray after hybridization.

  8. Distributed optically integrated manufacture system based on CORBA

    Science.gov (United States)

    Cen, Ming; Jiang, Jian-chun; Liu, Xing-fa; Hu, Rui-fei

    2007-12-01

    Focused on the shortcoming and insufficiency of reconfigurable manufacture system (RMS) for optical manufacturing in control layer and interface of manufacturing execution systems (MES) and control layer, the difference of MES-plan layer interface and that of MES-control layer is discussed, and an architecture of distributed optically integrated manufacture executing system based on fieldbus/Ethernet network and common object request broker architecture (CORBA) is presented. In this solution, the optical manufacture equipments are connected by fieldbus network, a gateway is used for the communication of fieldbus manufacture equipment and MES in the workshop, and CORBA services which provide a general interface for communication of heterogeneous fieldbus manufacture equipment of workshop are realized on the gateway. Then all specifics of heterogeneous fieldbus manufacture equipments are concealed, which show as virtual equipment and can be accessed in a simple and unified way. So the control layer is composed of virtual equipment and easy to be reconfigured. Similarly workshop management function components are modeled and encapsulated by CORBA interface, and MES could be integrated to RMS expediently. The optical integrated manufacture system presented is proved with good ability of flexible, reconfigurable, opening and high feasibility, and met the reconfigurable requirement of distributed optical manufacturing workshop preferably.

  9. Integrated optics bus access module for intramachine communication

    Science.gov (United States)

    Karioja, Pentti; Tammela, Simo K. T.; Hannula, Tapio

    1991-12-01

    The feasibility of a passive bidirectional fiber optic bus and the packaging considerations of a bus access module have been studied. The bus uses 110/125 micrometers HCS fiber and passive integrated optic couplers for bus access. The access couplers are asymmetric and were fabricated using a Ag-Na ion exchange process. The asymmetry of the coupler was 5 dB, the launch loss to the bus was 6 dB and the tap-off loss to the node was 11 dB. With the integrated optics coupler it is possible to connect 6 nodes to the bidirectional bus. It is also possible to realize a simple, easy-to-use, and reliable bus access module for intramachine communication. The integrated optics coupler, a LED chip, and a PIN-diode chip and transceiver electronics are packaged in an electrical connector with a two-fiber optical cable pigtail. Active and passive components are butt coupled to the coupler. The 0.5 dB alignment tolerances for the fiber pigtails, the LED, and the PIN-diode chips are +/- 5 micrometers .

  10. Optical and electrical properties of electrochemically deposited polyaniline/CeO2 hybrid nanocomposite film

    Institute of Scientific and Technical Information of China (English)

    Anees A. Ansari; M. A. M. Khan; M. Naziruddin Khan; Salman A. Alrokayan; M. Alhoshan; M. S. Alsalhi

    2011-01-01

    This paper reports the optical and electrical properties of electrochemically deposited polyaniline (PANI)/cerium oxide (CeO2) hybrid nano-composite film onto indium-fin-oxide (ITO) glass substrate. UV-visible spectroscopy and I-V characteristic were performed to study the optical and electrical parameters of the electrochemically deposited film. The film exhibited a strong absorption below 400 nm (3.10 eV) with a well defined absorbance peak at around 285 nm (4.35 eV). The estimated band gap of the CeO2 sample was 3.44 eV, higher than bulk CeO2 powder (Eg = 3.19 eV) due to the quantum confinement effect. Optical and electrochemical characteristics indicated that the electrical properties of PANI/CeO2 hybrid nanocomposite film are dominated by PANI doping.

  11. Optical Biosensor with Multienzyme System Immobilized onto Hybrid Membrane for Pesticides Determination

    Directory of Open Access Journals (Sweden)

    Lyubov Yotova

    2011-12-01

    Full Text Available A construction of optical biosensor based on simultaneous immobilization of acetylcholinesterase and choline oxidase enzymes for the detection of pesticides residues is described. Different kinds of novel SiO2 hybrid membranes were synthesized to be suitable for optical biosensors using sol-gel techniques. The bioactive component of the sensor consists of a multi-enzyme system including acetylcholinesterase and choline oxidase covalently immobilized on new hybrid membranes. The sensor exhibited a linear response to acetylcholine in a concentration range of 2.5 - 30 mM. Inhibition plots obtained from testing carbamate (carbofuran pesticides exhibited concentration dependent behaviour and showed linear profiles in concentration ranges between 5x10-8 - 5x10-7 M for carbofuran. The factors affecting the constructed optical biosensors were investigated.

  12. Hybrid models for hydrological forecasting: integration of data-driven and conceptual modelling techniques

    NARCIS (Netherlands)

    Corzo Perez, G.A.

    2009-01-01

    This book presents the investigation of different architectures of integrating hydrological knowledge and models with data-driven models for the purpose of hydrological flow forecasting. The models resulting from such integration are referred to as hybrid models. The book addresses the following top

  13. Hybrid models for hydrological forecasting: Integration of data-driven and conceptual modelling techniques

    NARCIS (Netherlands)

    Corzo Perez, G.A.

    2009-01-01

    This book presents the investigation of different architectures of integrating hydrological knowledge and models with data-driven models for the purpose of hydrological flow forecasting. The models resulting from such integration are referred to as hybrid models. The book addresses the following top

  14. The Integration of Psychomotor Skills in a Hybrid-PBL Dental Curriculum: The Clinical Clerkships.

    Science.gov (United States)

    Walton, Joanne N.; MacNeil, M. A. J.; Harrison, Rosamund L.; Clark, D. Christopher

    1998-01-01

    Describes the restructuring of clinical clerkships at the University of British Columbia (Canada) dental school as part of a new, hybrid, problem-based learning (PBL) curriculum, focusing on strategies for integrating development of psychomotor skills. Methods of achieving both horizontal and vertical integration of competencies through grouping…

  15. Hybrid models for hydrological forecasting: integration of data-driven and conceptual modelling techniques

    NARCIS (Netherlands)

    Corzo Perez, G.A.

    2009-01-01

    This book presents the investigation of different architectures of integrating hydrological knowledge and models with data-driven models for the purpose of hydrological flow forecasting. The models resulting from such integration are referred to as hybrid models. The book addresses the following

  16. Hybrid models for hydrological forecasting: Integration of data-driven and conceptual modelling techniques

    NARCIS (Netherlands)

    Corzo Perez, G.A.

    2009-01-01

    This book presents the investigation of different architectures of integrating hydrological knowledge and models with data-driven models for the purpose of hydrological flow forecasting. The models resulting from such integration are referred to as hybrid models. The book addresses the following

  17. Outcome of the First wwPDB Hybrid/Integrative Methods Task Force Workshop

    NARCIS (Netherlands)

    Sali, Andrej; Berman, Helen M.; Schwede, Torsten; Trewhella, Jill; Kleywegt, Gerard; Burley, Stephen K.; Markley, John; Nakamura, Haruki; Adams, Paul; Bonvin, Alexandre M J J|info:eu-repo/dai/nl/113691238; Chiu, Wah; Peraro, Matteo Dal; Di Maio, Frank; Ferrin, Thomas E.; Grünewald, Kay; Gutmanas, Aleksandras; Henderson, Richard; Hummer, Gerhard; Iwasaki, Kenji; Johnson, Graham; Lawson, Catherine L.; Meiler, Jens; Marti-Renom, Marc A.; Montelione, Gaetano T.; Nilges, Michael; Nussinov, Ruth; Patwardhan, Ardan; Rappsilber, Juri; Read, Randy J.; Saibil, Helen; Schröder, Gunnar F.; Schwieters, Charles D.; Seidel, Claus A M; Svergun, Dmitri; Topf, Maya; Ulrich, Eldon L.; Velankar, Sameer; Westbrook, John D.

    2015-01-01

    Structures of biomolecular systems are increasingly computed by integrative modeling that relies on varied types of experimental data and theoretical information. We describe here the proceedings and conclusions from the first wwPDB Hybrid/Integrative Methods Task Force Workshop held at the European

  18. YBCO Coated Conductor with an Integrated Optical Fiber Sensor

    Energy Technology Data Exchange (ETDEWEB)

    Sathyamurthy, Srivatsan [American Superconductor Corporation, Devens, MA (United States); Rupich, Marty [American Superconductor Corporation, Devens, MA (United States); Schwartz, Justin [North Carolina State Univ., Raleigh, NC (United States)

    2016-03-31

    The primary objectives of the Phase I Project was to develop a proof-of-principle for a concept of integrating an optical fiber sensor into the laminated 2G wire, there by producing a functionalized 2G wire with self-monitoring capabilities

  19. Monolithic integrated optic fiber Bragg grating sensor interrogator

    Science.gov (United States)

    Mendoza, Edgar A.; Esterkin, Yan; Kempen, Cornelia; Sun, Songjian

    2010-04-01

    Fiber Bragg gratings (FBGs) are a mature sensing technology that has gained rapid acceptance in civil, aerospace, chemical and petrochemical, medicine, aviation and automotive industries. Fiber Bragg grating sensors can be use for a variety of measurements including strain, stress, vibration, acoustics, acceleration, pressure, temperature, moisture, and corrosion distributed at multiple locations within the structure using a single fiber element. The most prominent advantages of FBGs are: small size and light weight, multiple FBG transducers on a single fiber, and immunity to radio frequency interference. A major disadvantage of FBG technology is that conventional state-of-the-art fiber Bragg grating interrogation systems are typically bulky, heavy, and costly bench top instruments that are assembled from off-the-shelf fiber optic and optical components integrated with a signal electronics board into an instrument console. Based on the need for a compact FBG interrogation system, this paper describes recent progress towards the development of a miniature fiber Bragg grating sensor interrogator (FBG-TransceiverTM) system based on multi-channel monolithic integrated optic sensor microchip technology. The integrated optic microchip technology enables the monolithic integration of all of the functionalities, both passive and active, of conventional bench top FBG sensor interrogators systems, packaged in a miniaturized, low power operation, 2-cm x 5-cm small form factor (SFF) package suitable for the long-term structural health monitoring in applications where size, weight, and power are critical for operation.

  20. Characterization of Integrated Optical Strain Sensors Based on Silicon Waveguides

    NARCIS (Netherlands)

    Westerveld, W.J.; Leinders, S.M.; Muilwijk, P.M.; Pozo, J.

    2013-01-01

    Microscale strain gauges are widely used in micro electro-mechanical systems (MEMS) to measure strains such as those induced by force, acceleration, pressure or sound. We propose all-optical strain sensors based on micro-ring resonators to be integrated with MEMS. We characterized the strain-induced

  1. Integrating Environmental Optics into Multidisciplinary, Predictive Models of Ocean Dynamics

    Science.gov (United States)

    2011-09-30

    development has been based on decades of published research, our depth-integrated, spectral model of photosynthesis and the absorption -based model of...color, chlorophyll fluorescence, or spectral absorption coefficients. We extend the approach to include additional biological properties such as...of laboratory experiments in which photosynthesis , fluorescence and optical properties of phytoplankton are measured under a range of conditions

  2. Deterministic Entanglement via Molecular Dissociation in Integrated Atom Optics

    OpenAIRE

    Zhao, Bo; Chen, Zeng-Bing; Pan, Jian-Wei; Schmiedmayer, J.; Recati, Alessio; Astrakharchik, Grigory E.; Calarco, Tommaso

    2005-01-01

    Deterministic entanglement of neutral cold atoms can be achieved by combining several already available techniques like the creation/dissociation of neutral diatomic molecules, manipulating atoms with micro fabricated structures (atom chips) and detecting single atoms with almost 100% efficiency. Manipulating this entanglement with integrated/linear atom optics will open a new perspective for quantum information processing with neutral atoms.

  3. A HYBRID GRANULARITY PARALLEL ALGORITHM FOR PRECISE INTEGRATION OF STRUCTURAL DYNAMIC RESPONSES

    Institute of Scientific and Technical Information of China (English)

    Yuanyin Li; Xianlong Jin; Genguo Li

    2008-01-01

    Precise integration methods to solve structural dynamic responses and the corre-sponding time integration formula are composed of two parts: the multiplication of an exponential matrix with a vector and the integration term. The second term can be solved by the series solu-tion. Two hybrid granularity parallel algorithms are designed, that is, the exponential matrix and the first term are computed by the fine-grained parallel algorithm and the second term is com-puted by the coarse-grained parallel algorithm. Numerical examples show that these two hybrid granularity parallel algorithms obtain higher speedup and parallel efficiency than two existing parallel algorithms.

  4. Compressive sensing in a photonic link with optical integration.

    Science.gov (United States)

    Chen, Ying; Yu, Xianbin; Chi, Hao; Jin, Xiaofeng; Zhang, Xianmin; Zheng, Shilie; Galili, Michael

    2014-04-15

    In this Letter, we present a novel structure to realize photonics-assisted compressive sensing (CS) with optical integration. In the system, a spectrally sparse signal modulates a multiwavelength continuous-wave light and then is mixed with a random sequence in optical domain. The optical signal passes through a length of dispersive fiber, the dispersion amount of which is set to ensure that the group delay between the adjacent wavelength channels is equal to the bit duration of the applied random sequence. As a result, the detected signal is a delay-and-sum version of the randomly mixed signal, which is equivalent to the function of integration required in CS. A proof-of-concept experiment with four wavelengths, corresponding to a compression factor of 4, is demonstrated. More simulation results are also given to show the potential of the technique.

  5. Proton Injection into the Fermilab Integrable Optics Test Accelerator (IOTA)

    Energy Technology Data Exchange (ETDEWEB)

    Prebys, Eric [Fermilab; Antipov, Sergey [Chicago U.; Piekarz, Henryk [Fermilab; Valishev, A. [Fermilab

    2015-06-01

    The Integrable Optics Test Accelerator (IOTA) is an experimental synchrotron being built at Fermilab to test the concept of non-linear "integrable optics". These optics are based on a lattice including non-linear elements that satisfies particular conditions on the Hamiltonian. The resulting particle motion is predicted to be stable but without a unique tune. The system is therefore insensitive to resonant instabilities and can in principle store very intense beams, with space charge tune shifts larger than those which are possible in conventional linear synchrotrons. The ring will initially be tested with pencil electron beams, but this poster describes the ultimate plan to install a 2.5 MeV RFQ to inject protons, which will produce tune shifts on the order of unity. Technical details will be presented, as well as simulations of protons in the ring.

  6. Proton Injection into the Fermilab Integrable Optics Test Accelerator (IOTA)

    Energy Technology Data Exchange (ETDEWEB)

    Prebys, Eric [Fermilab; Antipov, Sergey [Chicago U.; Piekarz, Henryk [Fermilab; Valishev, A. [Fermilab

    2015-06-01

    The Integrable Optics Test Accelerator (IOTA) is an experimental synchrotron being built at Fermilab to test the concept of non-linear "integrable optics". These optics are based on a lattice including non-linear elements that satisfies particular conditions on the Hamiltonian. The resulting particle motion is predicted to be stable but without a unique tune. The system is therefore insensitive to resonant instabilities and can in principle store very intense beams, with space charge tune shifts larger than those which are possible in conventional linear synchrotrons. The ring will initially be tested with pencil electron beams, but this poster describes the ultimate plan to install a 2.5 MeV RFQ to inject protons, which will produce tune shifts on the order of unity. Technical details will be presented, as well as simulations of protons in the ring.

  7. Hybrid materials science: a promised land for the integrative design of multifunctional materials.

    Science.gov (United States)

    Nicole, Lionel; Laberty-Robert, Christel; Rozes, Laurence; Sanchez, Clément

    2014-06-21

    For more than 5000 years, organic-inorganic composite materials created by men via skill and serendipity have been part of human culture and customs. The concept of "hybrid organic-inorganic" nanocomposites exploded in the second half of the 20th century with the expansion of the so-called "chimie douce" which led to many collaborations between a large set of chemists, physicists and biologists. Consequently, the scientific melting pot of these very different scientific communities created a new pluridisciplinary school of thought. Today, the tremendous effort of basic research performed in the last twenty years allows tailor-made multifunctional hybrid materials with perfect control over composition, structure and shape. Some of these hybrid materials have already entered the industrial market. Many tailor-made multiscale hybrids are increasingly impacting numerous fields of applications: optics, catalysis, energy, environment, nanomedicine, etc. In the present feature article, we emphasize several fundamental and applied aspects of the hybrid materials field: bioreplication, mesostructured thin films, Lego-like chemistry designed hybrid nanocomposites, and advanced hybrid materials for energy. Finally, a few commercial applications of hybrid materials will be presented.

  8. Hybrid materials science: a promised land for the integrative design of multifunctional materials

    Science.gov (United States)

    Nicole, Lionel; Laberty-Robert, Christel; Rozes, Laurence; Sanchez, Clément

    2014-05-01

    For more than 5000 years, organic-inorganic composite materials created by men via skill and serendipity have been part of human culture and customs. The concept of ``hybrid organic-inorganic'' nanocomposites exploded in the second half of the 20th century with the expansion of the so-called ``chimie douce'' which led to many collaborations between a large set of chemists, physicists and biologists. Consequently, the scientific melting pot of these very different scientific communities created a new pluridisciplinary school of thought. Today, the tremendous effort of basic research performed in the last twenty years allows tailor-made multifunctional hybrid materials with perfect control over composition, structure and shape. Some of these hybrid materials have already entered the industrial market. Many tailor-made multiscale hybrids are increasingly impacting numerous fields of applications: optics, catalysis, energy, environment, nanomedicine, etc. In the present feature article, we emphasize several fundamental and applied aspects of the hybrid materials field: bioreplication, mesostructured thin films, Lego-like chemistry designed hybrid nanocomposites, and advanced hybrid materials for energy. Finally, a few commercial applications of hybrid materials will be presented.

  9. Hybrid State-Space Time Integration of Rotating Beams

    DEFF Research Database (Denmark)

    Nielsen, Martin Bjerre; Krenk, Steen

    2010-01-01

    Modeling and efficien design of wind turbines require efficien and accurate computational methods for dynamic analysis of the different components. In the present paper an efficien hybrid formulation for beams in a rotating frame of reference is presented for analysis of the rotor system. It is d...

  10. Integrated magneto-optical traps on a chip

    CERN Document Server

    Pollock, S; Laliotis, A; Hinds, E A

    2009-01-01

    We have integrated magneto-optical traps (MOTs) into an atom chip by etching pyramids into a silicon wafer. These have been used to trap atoms on the chip, directly from a room temperature vapor of rubidium. This new atom trapping method provides a simple way to integrate several atom sources on the same chip. It represents a substantial advance in atom chip technology and offers new possibilities for atom chip applications such as integrated single atom or photon sources and molecules on a chip.

  11. Hybrid integration of III-V and silicon materials and devices

    Science.gov (United States)

    Luo, Zhongsheng

    Laser liftoff (LLO) based hybrid integration techniques including the double-transfer process and the pixel-to-point transfer process have been developed to integrate III-V photonics with silicon materials and circuitry. No degradation in the device performance has been observed using the LLO based transfer techniques. On the contrary, performance improvements in both electrical characteristics and electroluminescence (EL) output have been found for the (In,Ga)N light emitting diodes (LEDs) transferred onto Si substrate. Based on computer simulation, it is found that as much as 70% enhancement in EL output could be expected by optimizing the metal layering on the backside of the transferred LEDs. In order to understand the existing experimental data and improve controllability and damage-free transfer yield of the LLO process, a novel, comprehensive LLO model based on thermal-mechanical analysis has been proposed and developed. The LLO model has been validated in the well-studied GaN/sapphire system. By employing the LLO based transfer technique, two optoelectronic systems have been designed and demonstrated. The first one is an integrated fluorescence microsystem, which involved the integration of Cd(S,Se) bandgap filters, (In,Ga)N LEDs, Poly(dimethylsiloxane) (PDMS) microfluidic channels with a pre-fabricated Si PIN photodiode chip. Prototypes with both one color (blue LED) excitation and two-color (blue and green LED) excitation have consistently demonstrated a detection capability of as low as 1 nM fluosphere beads using Molecular Probes FluoSpheresRTM dye. Furthermore, the feasibility of multi-wavelength design has been verified using the bi-wavelength prototype. To optimize signal-to-noise ratio and detection sensitivity of the microsystem via system design, an in-depth mathematic analysis has also been performed. The second application is a zero-footprint optical metrology wafer, which relies on the reflection at the optical detection window, through which

  12. Hybrid Quantum System of a Nanofiber Mode Coupled to Two Chains of Optically Trapped Atoms

    CERN Document Server

    Zoubi, Hashem

    2010-01-01

    A tapered optical nanofiber simultaneously used to trap and optically interface of cold atoms through evanescent fields constitutes a new and well controllable hybrid quantum system. The atoms are trapped in two parallel 1D optical lattices generated by suitable far blue and red detuned evanescent field modes very close to opposite sides of the nanofiber surface. Collective electronic excitations (excitons) of each of the optical lattices are resonantly coupled to the second lattice forming symmetric and antisymmetric common excitons. In contrast to the inverse cube dependence of the individual atomic dipole-dipole interaction, we analytically find an exponentially decaying coupling strength with distance between the lattices. The resulting symmetric (bright) excitons strongly interact with the resonant nanofiber photons to form fiber polaritons, which can be observed through linear optical spectra. For large enough wave vectors the polariton decay rate to free space is strongly reduced, which should render t...

  13. Optical pulse shaper with integrated slab waveguide for arbitrary waveform generation using optical gradient force

    Science.gov (United States)

    Liao, Sha-Sha; Min, Shu-Cun; Dong, Jian-Ji

    2014-12-01

    Integrated optical pulse shaper opens up possibilities for realizing the ultra high-speed and ultra wide-band linear signal processing with compact size and low power consumption. We propose a silicon monolithic integrated optical pulse shaper using optical gradient force, which is based on the eight-path finite impulse response. A cantilever structure is fabricated in one arm of the Mach—Zehnder interferometer (MZI) to act as an amplitude modulator. The phase shift feature of waveguide is analyzed with the optical pump power, and five typical waveforms are demonstrated with the manipulation of optical force. Unlike other pulse shaper schemes based on thermo—optic effect or electro—optic effect, our scheme is based on a new degree of freedom manipulation, i.e., optical force, so no microelectrodes are required on the silicon chip, which can reduce the complexity of fabrication. Besides, the chip structure is suitable for commercial silicon on an insulator (SOI) wafer, which has a top silicon layer of about 220 nm in thickness.

  14. Hybrid Radio/Free-Space Optical Design for Next Generation Backhaul Systems

    KAUST Repository

    Douik, Ahmed

    2016-04-22

    The deluge of date rate in today\\'s networks imposes a cost burden on the backhaul network design. Developing cost-efficient backhaul solutions becomes an exciting, yet challenging, problem. Traditional technologies for backhaul networks, including either radio-frequency (RF) backhauls or optical fibers (OF). While RF is a cost-effective solution as compared with OF, it supports the lower data rate requirements. Another promising backhaul solution is the free-space optics (FSO) as it offers both a high data rate and a relatively low cost. The FSO, however, is sensitive to nature conditions, e.g., rain, fog, and line-of-sight. This paper combines both the RF and FSO advantages and proposes a hybrid RF/FSO backhaul solution. It considers the problem of minimizing the cost of the backhaul network by choosing either OF or hybrid RF/FSO backhaul links between the base stations, so as to satisfy data rate, connectivity, and reliability constraints. It shows that under a specified realistic assumption about the cost of OF and hybrid RF/FSO links, the problem is equivalent to a maximum weight clique problem, which can be solved with moderate complexity. Simulation results show that the proposed solution shows a close-to-optimal performance, especially for reasonable prices of the hybrid RF/FSO links. They further reveal that the hybrid RF/FSO is a cost-efficient solution and a good candidate for upgrading the existing backhaul networks. © 2016 IEEE.

  15. Optical Code-Division Multiple-Access and Wavelength Division Multiplexing: Hybrid Scheme Review

    Directory of Open Access Journals (Sweden)

    P. Susthitha Menon

    2012-01-01

    Full Text Available Problem statement: Hybrid Optical Code-Division Multiple-Access (OCDMA and Wavelength-Division Multiplexing (WDM have flourished as successful schemes for expanding the transmission capacity as well as enhancing the security for OCDMA. However, a comprehensive review related to this hybrid system are lacking currently. Approach: The purpose of this paper is to review the literature on OCDMA-WDM overlay systems, including our hybrid approach of one-dimensional coding of SAC OCDMA with WDM signals. In addition, we present an additional review of other categorios of hybrid WDM/OCDMA schemes, where codes of OCDMA can be employed on each WDM wavelength. Furthermore, an essential background of OCDMA, recent coding techniques and security issues are also presented. Results: Our results indicate that the feasibility of transmitting both OCDMA and WDM users on the same spectrum band can be achieved using MQC family code with an acceptable performance as well as good data confidentiality. In addition, the WDM interference signals can be suppressed properly for detection of optical broadband CDMA using notch filters. Conclusion: The paper provides a comprehensive overview of hybrid OCDMA-WDM systems and can be used as a baseline study for other scientists in the similar scope of research.

  16. Chromatic and Dispersive Effects in Nonlinear Integrable Optics

    CERN Document Server

    Webb, Stephen D; Valishev, Alexander; Nagaitsev, Sergei N; Danilov, Viatcheslav V

    2015-01-01

    Proton accumulator rings and other circular hadron accelerators are susceptible to intensity-driven parametric instabilities because the zero-current charged particle dynamics are characterized by a single tune. Landau damping can suppress these instabilities, which requires energy spread in the beam or introducing nonlinear magnets such as octupoles. However, this approach reduces dynamic aperture. Nonlinear integrable optics can suppress parametric instabilities independent of energy spread in the distribution, while preserving the dynamic aperture. This novel approach promises to reduce particle losses and enable order-of-magnitude increases in beam intensity. In this paper we present results, obtained using the Lie operator formalism, on how chromaticity and dispersion affect particle orbits in integrable optics. We conclude that chromaticity in general breaks the integrability, unless the vertical and horizontal chromaticities are equal. Because of this, the chromaticity correcting magnets can be weaker ...

  17. Streamline integration using MPI-hybrid parallelism on a large multicore architecture.

    Science.gov (United States)

    Camp, David; Garth, Christoph; Childs, Hank; Pugmire, Dave; Joy, Kenneth I

    2011-11-01

    Streamline computation in a very large vector field data set represents a significant challenge due to the nonlocal and data-dependent nature of streamline integration. In this paper, we conduct a study of the performance characteristics of hybrid parallel programming and execution as applied to streamline integration on a large, multicore platform. With multicore processors now prevalent in clusters and supercomputers, there is a need to understand the impact of these hybrid systems in order to make the best implementation choice. We use two MPI-based distribution approaches based on established parallelization paradigms, parallelize over seeds and parallelize over blocks, and present a novel MPI-hybrid algorithm for each approach to compute streamlines. Our findings indicate that the work sharing between cores in the proposed MPI-hybrid parallel implementation results in much improved performance and consumes less communication and I/O bandwidth than a traditional, nonhybrid distributed implementation.

  18. Integrating nanophotonic concepts and topics into optics curricula

    Science.gov (United States)

    Sonek, Gregory J.

    2007-06-01

    Nanophotonics has emerged as a new and important field of study, not only in research, but also in undergraduate optics and photonics education and training. Beyond the study of classical and quantum optics, it is important for students to learn about how the flow of light can be manipulated on a nanoscale level, and used in applications such as telecommunications, imaging, and medicine. This paper reports on our work to integrate basic nanophotonic concepts and topics into existing optics and optical electronics courses, as well as independent study projects, at the undergraduate level. Through classroom lectures, topical readings, computer modeling exercises, and laboratory experiments, students are introduced to nanophotonic concepts subsequent to a study of physical and geometrical optics. A compare and contrast methodology is employed to help students identify similarities and differences that exist in the optical behavior of bulk and nanostructured media. Training is further developed through engineering design and simulation exercises that use advanced, vector-diffraction-based, modeling software for simulating the performance of various materials and structures. To date, the addition of a nanophotonics component to the optics curriculum has proven successful, been enthusiastically received by students, and should serve as a basis for further course development efforts that emphasize the combined capabilities of nanotechnology and photonics.

  19. Effects of optical backscattering on silicon photonic hybrid laser performance

    Science.gov (United States)

    Pacradouni, V.; Klein, J.; Pond, J.

    2016-04-01

    We present numerical results on the effect of backscattering at the junctions of double bus ring resonators in a Vernier ring hybrid laser design. The structure is comprised off a pair of III-V gain media evanescently coupled to a silicon on insulator racetrack comprised of a pair of double bus ring resonators coupled together through straight and flared waveguide sections. We show how the small backscattering at the ring resonator junctions has the effect of splitting and shifting the resonances off the clockwise and counter clockwise propagating modes thereby modifying the feedback spectrum from the ideal case. We then simulate results such as light current (LI) curves, relative intensity noise (RIN) and laser spectrum, and compare the laser performance including backscattering effects with the ideal case.

  20. Performing derivative and integral operations for optical waves with optical metamaterials

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Cun-Li [College of Engineering, Nanjing Agriculture University, Nanjing Jiangsu, 210031 (China); College of Science, Nanjing Agriculture University, Nanjing Jiangsu, 210095 (China); Zhao, Zhi-Gang; Li, Xiao-Lin [College of Engineering, Nanjing Agriculture University, Nanjing Jiangsu, 210031 (China); Yang, Hong-Wei, E-mail: phd_hwyang@njau.edu.cn [College of Science, Nanjing Agriculture University, Nanjing Jiangsu, 210095 (China)

    2016-12-01

    The graded refractive index waveguides can perform Fourier transform for an optical wave. According to this characteristic, simpler optical metamaterials with three waveguides are theoretically proposed, in which all of the waveguides are materials with a positive refractive index. By selecting the appropriate refractive index and structure size, the theory and simulations demonstrated that these metamaterials can perform mathematical operations for the outline of incident optical waves, including the first-order derivative, second-order derivative and the integral. - Highlights: • The derivative and integral operations of optical waves are achieved with a simpler model. • Both negative and positive refractive index boast the same functions. • The mathematical operations can be implemented only by changing the refractive index of the intermediate material. • The results will greatly expand the possible applications, including photon computers, picture processing, video displays and data storage.

  1. Integration profile and safety of an adenovirus hybrid-vector utilizing hyperactive sleeping beauty transposase for somatic integration.

    Directory of Open Access Journals (Sweden)

    Wenli Zhang

    Full Text Available We recently developed adenovirus/transposase hybrid-vectors utilizing the previously described hyperactive Sleeping Beauty (SB transposase HSB5 for somatic integration and we could show stabilized transgene expression in mice and a canine model for hemophilia B. However, the safety profile of these hybrid-vectors with respect to vector dose and genotoxicity remains to be investigated. Herein, we evaluated this hybrid-vector system in C57Bl/6 mice with escalating vector dose settings. We found that in all mice which received the hyperactive SB transposase, transgene expression levels were stabilized in a dose-dependent manner and that the highest vector dose was accompanied by fatalities in mice. To analyze potential genotoxic side-effects due to somatic integration into host chromosomes, we performed a genome-wide integration site analysis using linker-mediated PCR (LM-PCR and linear amplification-mediated PCR (LAM-PCR. Analysis of genomic DNA samples obtained from HSB5 treated female and male mice revealed a total of 1327 unique transposition events. Overall the chromosomal distribution pattern was close-to-random and we observed a random integration profile with respect to integration into gene and non-gene areas. Notably, when using the LM-PCR protocol, 27 extra-chromosomal integration events were identified, most likely caused by transposon excision and subsequent transposition into the delivered adenoviral vector genome. In total, this study provides a careful evaluation of the safety profile of adenovirus/Sleeping Beauty transposase hybrid-vectors. The obtained information will be useful when designing future preclinical studies utilizing hybrid-vectors in small and large animal models.

  2. Four dimensional hybrid ultrasound and optoacoustic imaging via passive element optical excitation in a hand-held probe

    Energy Technology Data Exchange (ETDEWEB)

    Fehm, Thomas Felix; Razansky, Daniel, E-mail: dr@tum.de [Institute for Biological and Medical Imaging (IBMI), Helmholtz Zentrum München, Neuherberg (Germany); Faculty of Medicine, Technische Universität München, Munich (Germany); Deán-Ben, Xosé Luís [Institute for Biological and Medical Imaging (IBMI), Helmholtz Zentrum München, Neuherberg (Germany)

    2014-10-27

    Ultrasonography and optoacoustic imaging share powerful advantages related to the natural aptitude for real-time image rendering with high resolution, the hand-held operation, and lack of ionizing radiation. The two methods also possess very different yet highly complementary advantages of the mechanical and optical contrast in living tissues. Nonetheless, efficient integration of these modalities remains challenging owing to the fundamental differences in the underlying physical contrast, optimal signal acquisition, and image reconstruction approaches. We report on a method for hybrid acquisition and reconstruction of three-dimensional pulse-echo ultrasound and optoacoustic images in real time based on passive ultrasound generation with an optical absorber, thus avoiding the hardware complexity of active ultrasound generation. In this way, complete hybrid datasets are generated with a single laser interrogation pulse, resulting in simultaneous rendering of ultrasound and optoacoustic images at an unprecedented rate of 10 volumetric frames per second. Performance is subsequently showcased in phantom experiments and in-vivo measurements from a healthy human volunteer, confirming general clinical applicability of the method.

  3. Molecular verification of the integration of Tripsacum dactyloides DNA into wheat genome through wide hybridization

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    RAPD and RFLP analyses of double haploid lines which derived from hybridization between hexaploid wheat (Triticum aestivum L.2n=42) and eastern gamagrass (Tripsacum dactyloides L.2n=4x=72) are reported.Two of the 340 Operon primers have been screened,which stably amplified Tripsacum dactyloides (male parent) specific bands in the double haploid lines.These results confirm the fact that Tripsacum dactyloides DNA has been integrated into wheat genome by sexual hybridization at molecular level.This idea has been further testified by RFLP analysis.Application and potentials of transferring Tripsacum dactyloides DNA into wheat genome by sexual hybridization in wheat breeding are discussed.

  4. High-dynamic-range hybrid analog-digital control broadband optical spectral processor using micromirror and acousto-optic devices.

    Science.gov (United States)

    Riza, Nabeel A; Reza, Syed Azer

    2008-06-01

    For the first time, to the best of our knowledge, the design and demonstration of a programmable spectral filtering processor is presented that simultaneously engages the power of an analog-mode optical device such as an acousto-optic tunable filter and a digital-mode optical device such as the digital micromirror device. The demonstrated processor allows a high 50 dB attenuation dynamic range across the chosen 1530-1565 nm (~C band). The hybrid analog-digital spectral control mechanism enables the processor to operate with greater versatility when compared to analog- or digital-only processor designs. Such a processor can be useful both as a test instrument in biomedical applications and as an equalizer in fiber communication networks.

  5. Spatial and temporal variability in response to hybrid electro-optical stimulation

    Science.gov (United States)

    Duke, Austin R.; Lu, Hui; Jenkins, Michael W.; Chiel, Hillel J.; Jansen, E. Duco

    2012-06-01

    Hybrid electro-optical neural stimulation is a novel paradigm combining the advantages of optical and electrical stimulation techniques while reducing their respective limitations. However, in order to fulfill its promise, this technique requires reduced variability and improved reproducibility. Here we used a comparative physiological approach to aid the further development of this technique by identifying the spatial and temporal factors characteristic of hybrid stimulation that may contribute to experimental variability and/or a lack of reproducibility. Using transient pulses of infrared light delivered simultaneously with a bipolar electrical stimulus in either the marine mollusk Aplysia californica buccal nerve or the rat sciatic nerve, we determined the existence of a finite region of excitability with size altered by the strength of the optical stimulus and recruitment dictated by the polarity of the electrical stimulus. Hybrid stimulation radiant exposures yielding 50% probability of firing (RE50) were shown to be negatively correlated with the underlying changes in electrical stimulation threshold over time. In Aplysia, but not in the rat sciatic nerve, increasing optical radiant exposures (J cm-2) beyond the RE50 ultimately resulted in inhibition of evoked potentials. Accounting for the sources of variability identified in this study increased the reproducibility of stimulation from 35% to 93% in Aplysia and 23% to 76% in the rat with reduced variability.

  6. Hybrid Finite Element-Fast Spectral Domain Multilayer Boundary Integral Modeling of Doubly Periodic Structures

    Energy Technology Data Exchange (ETDEWEB)

    T.F. Eibert; J.L. Volakis; Y.E. Erdemli

    2002-03-03

    Hybrid finite element (FE)--boundary integral (BI) analysis of infinite periodic arrays is extended to include planar multilayered Green's functions. In this manner, a portion of the volumetric dielectric region can be modeled via the finite element method whereas uniform multilayered regions can be modeled using a multilayered Green's function. As such, thick uniform substrates can be modeled without loss of efficiency and accuracy. The multilayered Green's function is analytically computed in the spectral domain and the resulting BI matrix-vector products are evaluated via the fast spectral domain algorithm (FSDA). As a result, the computational cost of the matrix-vector products is kept at O(N). Furthermore, the number of Floquet modes in the expansion are kept very few by placing the BI surfaces within the computational unit cell. Examples of frequency selective surface (FSS) arrays are analyzed with this method to demonstrate the accuracy and capability of the approach. One example involves complicated multilayered substrates above and below an inhomogeneous filter element and the other is an optical ring-slot array on a substrate several hundred wavelengths in thickness. Comparisons with measurements are included.

  7. Chip-integrated plasmonic Schottky photodetection based on hybrid silicon waveguides

    Science.gov (United States)

    Lu, Hua; Gu, Min

    2017-03-01

    We numerically and theoretically investigate the plasmonic Schottky photodetection in a novel hybrid silicon-on-insulator waveguide system, which consists of the silicon waveguides and detection area with the metal stripes and doped silicon film on the silicon dioxide substrate. The results illustrate that the fundamental TE mode in the silicon waveguide can be effectively coupled into the metal/silicon waveguide with the excitation of surface plasmon polaritons (SPPs). The coupling is suppressed for the TM mode due to the mismatch between the electric field distributions of the TM and SPP modes. It is found that the coupling efficiency from the TE to SPP mode is dependent on the width and height of the silicon waveguide and can significantly approach 36.1%. The ultracompact configuration yields a high responsivity of 21.7 mA/W and low dark current of 0.45 μA for the photodetection at the communication wavelength. The plasmonic Schottky photodetector could find favorable applications in the chip-integrated optical interconnects and signal processing.

  8. Metal-dielectric hybrid surfaces as integrated optoelectronic interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Narasimhan, Vijay K.; Hymel, Thomas M.; Lai, Ruby A.; Cui, Yi

    2017-01-03

    An optoelectronic device has a hybrid metal-dielectric optoelectronic interface including an array of nanoscale dielectric resonant elements (e.g., nanopillars), and a metal film disposed between the dielectric resonant elements and below a top surface of the resonant elements such that the dielectric resonant elements protrude through the metal film. The device may also include an anti-reflection coating. The device may further include a metal film layer on each of the dielectric resonant elements.

  9. Integrated optics architecture for trapped-ion quantum information processing

    Science.gov (United States)

    Kielpinski, D.; Volin, C.; Streed, E. W.; Lenzini, F.; Lobino, M.

    2016-12-01

    Standard schemes for trapped-ion quantum information processing (QIP) involve the manipulation of ions in a large array of interconnected trapping potentials. The basic set of QIP operations, including state initialization, universal quantum logic, and state detection, is routinely executed within a single array site by means of optical operations, including various laser excitations as well as the collection of ion fluorescence. Transport of ions between array sites is also routinely carried out in microfabricated trap arrays. However, it is still not possible to perform optical operations in parallel across all array sites. The lack of this capability is one of the major obstacles to scalable trapped-ion QIP and presently limits exploitation of current microfabricated trap technology. Here we present an architecture for scalable integration of optical operations in trapped-ion QIP. We show theoretically that diffractive mirrors, monolithically fabricated on the trap array, can efficiently couple light between trap array sites and optical waveguide arrays. Integrated optical circuits constructed from these waveguides can be used for sequencing of laser excitation and fluorescence collection. Our scalable architecture supports all standard QIP operations, as well as photon-mediated entanglement channels, while offering substantial performance improvements over current techniques.

  10. In-fiber integrated chemiluminiscence online optical fiber sensor.

    Science.gov (United States)

    Yang, Xinghua; Yuan, Tingting; Yang, Jun; Dong, Biao; Liu, Yanxin; Zheng, Yao; Yuan, Libo

    2013-09-01

    We report an in-fiber integrated chemiluminiscence (CL) sensor based on a kind of hollow optical fiber with a suspended inner core. The path of microfluid is realized by etching microholes for inlets and outlets on the surface of the optical fiber without damaging the inner core and then constructing a melted point beside the microhole of the outlet. When samples are injected into the fiber, the liquids can be fully mixed and form steady microflows. Simultaneously, the photon emitted from the CL reaction is efficiently coupled into the core and can be detected at the end of the optical fiber. In this Letter, the concentration of H2O2 samples is analyzed through the emission intensity of the CL reaction among H2O2, luminol, K3Fe(CN)6, and NaOH in the optical fiber. The linear sensing range of 0.1-4.0 mmol/L of H2O2 concentration is obtained. The emission intensity can be determined within 400 ms at a total flow rate of 150 μL/min. Significantly, this work presents the information of developing in-fiber integrated online analyzing devices based on optical methods.

  11. Performance study of macro-bending EDFA/Raman hybrid optical fiber amplifiers

    Science.gov (United States)

    Mahran, O.

    2015-10-01

    In this paper, we present an analytical study of a (macro-bending EDFA)/Raman hybrid optical amplifier. The bending radius is 4 mm with EDFA length 10 m with forward pump power in the range (100-500 mW) and Raman amplifier length (12-55 km) with backward pump power variations (80-200 mW) is considered in our model. Due to bending loss in EDFA, the gain of hybrid amplifier is increased to ~7 dB more than the normal EDFA/Raman hybrid amplifier and the noise figure is decreased by ~2 dB rather than without macro-bending EDFA/Raman hybrid amplifier. The signal to noise ratio (OSNR) calculations shows a better performance of macro-bending EDFA/Raman hybrid amplifier than without macro-bending one. A flat gain is obtained in the signal wavelength region (1560-1600 nm), which is the L-band. The calculated results for macro-bending case are compared with experimental results of normal case by Lee et al., in the L-band showing an increase in the gain, reduction in the noise figure and more gain flatness at the input signal -20 dBm for macro-bending EDFA/Raman hybrid amplifier.

  12. Hybrid structure of biotemplate-zinc-tin oxide for better optical, morphological and photocatalytic properties

    Science.gov (United States)

    Karpuraranjith, M.; Thambidurai, S.

    2017-03-01

    A new chitosan (as biotemplate)-zinc-tin oxide hybrid structure was successfully synthesized by a chemical precipitation method and annealed at 500 °C. We studied the structural changes, optical, thermal and photo catalytic properties. The chemical bonding of the Zn-O and Sn-O-Sn functional groups were confirmed by FT-IR absorption peaks appearing at 538 and 635 cm‑1. The different ratio of ZnO to SnO2 particles on the biotemplate matrix altered the morphology of the hybrids from an agglomerated state to a microcrystalline form confirmed by HR-SEM and TEM analysis. The formation of a Zn0.15Sn0.85O hybrid structure was observed in the visible light region, with an energy band gap of ∼3.19 eV and higher surface area of 98 m2 g‑1. The thermal property shows that CS-Zn0.15Sn0.85O has a higher thermal stability than a CS-Zn0.25Sn0.75O hybrid structure. The results demonstrate that the biotemplate-zinc-tin oxide hybrid structure has a reinforced effect compared to the other components. Therefore, a biotemplate-based zinc-tin oxide hybrid structure could be a promising material for better dye removal efficiency, which was obtained for ∼100 and 96% with MB and RY-15 dyes.

  13. Validation of a Hybrid Microwave-Optical Monitor to Investigate Thermal Provocation in the Microvasculature.

    Science.gov (United States)

    Al-Armaghany, Allann; Tong, Kenneth; Highton, David; Leung, Terence S

    2016-01-01

    We have previously developed a hybrid microwave-optical system to monitor microvascular changes in response to thermal provocation in muscle. The hybrid probe is capable of inducing deep heat from the skin surface using mild microwaves (1-3 W) and raises the tissue temperature by a few degrees Celsius. This causes vasodilation and the subsequent increase in blood volume is detected by the hybrid probe using near infrared spectroscopy. The hybrid probe is also equipped with a skin cooling system which lowers the skin temperature while allowing microwaves to warm up deeper tissues. The hybrid system can be used to assess the condition of the vasculature in response to thermal stimulation. In this validation study, thermal imaging has been used to assess the temperature distribution on the surface of phantoms and human calf, following microwave warming. The results show that the hybrid system is capable of changing the skin temperature with a combination of microwave warming and skin cooling. It can also detect thermal responses in terms of changes of oxy/deoxy-hemoglobin concentrations.

  14. Nonlinear Optics in Optoelectronic Integration with Some Novel Waveguide Devices.

    Science.gov (United States)

    Vakhshoori, Daryoosh

    By integration we mean realizing an integrable solution to existing discrete devices which perform some useful operation. Systems are built from these functional parts. System integration requires compatible integration of these parts. At present the most important example that also relates to our work is communication systems. For this system to work reliably, the optical pulses should be stable in time and shape (small time and amplitude jitter.) The devices that measure these properties are optical correlators. These devices are bulky, occupying a cubic foot of volume with no satisfactory integrable counterpart. Here we present an integrable waveguide correlator which experimentally measured pulses from 150fsec to 12psec with an average guide power of sub mW to 2mW in the spectral range of 1.7mum to 1.06mu m. All these measurements were performed on the same waveguide structure without mechanical movements where the spectral range was limited to the band gap of the waveguide material, GaAs in our case. The other communication scheme uses wavelength division multiplexing. Optical spectrometers are ~1 meter long devices capable of 0.1A spectral resolution. Again, like correlators, there is no satisfactory integrable counterpart. In this thesis, we present an integrable parametric waveguide spectrometer capable of measuring individual modes of semiconductor laser diodes and their movement as a function of laser current. For our experiments, the resolving power of the waveguide device was about 3A and is easily extendible to the sub A range. It should be pointed out that these spectrometer devices can also be used in stabilizing laser diode frequencies which are required for the realization of reliable wavelength division multiplexed systems. Last, but not least, a possible coherent visible surface emitting waveguide device capable of mW range powers is also presented. The motivation for this study is the ever growing market for shorter wavelength semiconductor

  15. Hybrid CATV/MMW/BB lightwave transmission system based on fiber-wired/fiber-wireless/fiber-VLLC integrations.

    Science.gov (United States)

    Li, Chung-Yi; Lu, Hai-Han; Lu, Ting-Chieh; Chu, Chien-An; Chen, Bo-Rui; Lin, Chun-Yu; Peng, Peng-Chun

    2015-12-14

    A hybrid lightwave transmission system for cable television (CATV)/millimeter-wave (MMW)/baseband (BB) signal transmission based on fiber-wired/fiber-wireless/fiber-visible laser light communication (VLLC) integrations is proposed and demonstrated. For down-link transmission, the light is intensity-modulated with 50-550 MHz CATV signal and optically promoted from 25 GHz radio frequency (RF) signal to 10 Gbps/50 GHz and 20 Gbps/100 GHz MMW data signals based on fiber-wired and fiber-wireless integrations. Good performances of carrier-to-noise ratio (CNR), composite second-order (CSO), composite triple-beat (CTB), and bit error rate (BER) are obtained over a 40-km single-mode fiber (SMF) and a 10-m RF wireless transport. For up-link transmission, the light is successfully intensity-remodulated with 5-Gbps BB data stream based on fiber-VLLC integration. Good BER performance is achieved over a 40-km SMF and a 10-m free-space VLLC transport. Such a hybrid CATV/MMW/BB lightwave transmission system is an attractive alternative, it gives the benefits of a communication link for broader bandwidth and higher transmission rate.

  16. Hybrid optical pumping of optically dense alkali-metal vapor without quenching gas

    CERN Document Server

    Romalis, M V

    2010-01-01

    Optical pumping of an optically thick atomic vapor typically requires a quenching buffer gas, such as N$_{2}$, to prevent radiation trapping of unpolarized photons which would depolarize the atoms. We show that optical pumping of a trace contamination of Rb present in K metal results in a 4.5 times higher polarization of K than direct optical pumping of K in the absence of N$_{2}$. Such spin-exchange polarization transfer from optically-thin species is useful in a variety of areas, including spin-polarized nuclear scattering targets and electron beams, quantum-non-demolition spin measurements, and ultra-sensitive magnetometry.

  17. SINET3: advanced optical and IP hybrid network

    Science.gov (United States)

    Urushidani, Shigeo

    2007-11-01

    This paper introduces the new Japanese academic backbone network called SINET3, which has been in full-scale operation since June 2007. SINET3 provides a wide variety of network services, such as multi-layer transfer, enriched VPN, enhanced QoS, and layer-1 bandwidth on demand (BoD) services to create an innovative and prolific science infrastructure for more than 700 universities and research institutions. The network applies an advanced hybrid network architecture composed of 75 layer-1 switches and 12 high-performance IP routers to accommodate such diversified services in a single network platform, and provides sufficient bandwidth using Japan's first STM256 (40 Gbps) lines. The network adopts lots of the latest networking technologies, such as next-generation SDH (VCAT/GFP/LCAS), GMPLS, advanced MPLS, and logical-router technologies, for high network convergence, flexible resource assignment, and high service availability. This paper covers the network services, network design, and networking technologies of SINET3.

  18. Extreme Environment Silicon Carbide Hybrid Temperature & Pressure Optical Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Nabeel Riza

    2010-09-01

    This final report contains the main results from a 3-year program to further investigate the merits of SiC-based hybrid sensor designs for extreme environment measurements in gas turbines. The study is divided in three parts. Part 1 studies the material properties of SiC such as temporal response, refractive index change with temperature, and material thermal response reversibility. Sensor data from a combustion rig-test using this SiC sensor technology is analyzed and a robust distributed sensor network design is proposed. Part 2 of the study focuses on introducing redundancy in the sensor signal processing to provide improved temperature measurement robustness. In this regard, two distinct measurement methods emerge. A first method uses laser wavelength sensitivity of the SiC refractive index behavior and a second method that engages the Black-Body (BB) radiation of the SiC package. Part 3 of the program investigates a new way to measure pressure via a distance measurement technique that applies to hot objects including corrosive fluids.

  19. Hybridization of detector array and integrated circuit for readout

    Science.gov (United States)

    Fossum, Eric R.; Grunthaner, Frank J.

    1992-04-01

    A process is explained for fabricating a detector array in a layer of semiconductor material on one substrate and an integrated readout circuit in a layer of semiconductor material on a separate substrate in order to select semiconductor material for optimum performance of each structure, such as GaAs for the detector array and Si for the integrated readout circuit. The detector array layer is lifted off its substrate, laminated on the metallized surface on the integrated surface, etched with reticulating channels to the surface of the integrated circuit, and provided with interconnections between the detector array pixels and the integrated readout circuit through the channels. The adhesive material for the lamination is selected to be chemically stable to provide electrical and thermal insulation and to provide stress release between the two structures fabricated in semiconductor materials that may have different coefficients of thermal expansion.

  20. Monolithically integrated quantum dot optical modulator with semiconductor optical amplifier for thousand and original band optical communication

    Science.gov (United States)

    Yamamoto, Naokatsu; Akahane, Kouichi; Umezawa, Toshimasa; Matsumoto, Atsushi; Kawanishi, Tetsuya

    2016-04-01

    A monolithically integrated quantum dot (QD) optical gain modulator (OGM) with a QD semiconductor optical amplifier (SOA) was successfully developed with T-band (1.0 µm waveband) and O-band (1.3 µm waveband) QD optical gain materials for Gbps-order, high-speed optical data generation. The insertion loss due to coupling between the device and the optical fiber was effectively compensated for by the SOA section. It was also confirmed that the monolithic QD-OGM/SOA device enabled >4.8 Gbps optical data generation with a clear eye opening in the T-band. Furthermore, we successfully demonstrated error-free 4.8 Gbps optical data transmissions in each of the six wavelength channels over a 10-km-long photonic crystal fiber using the monolithic QD-OGM/SOA device in multiple O-band wavelength channels, which were generated by the single QD gain chip. These results suggest that the monolithic QD-OGM/SOA device will be advantageous in ultra-broadband optical frequency systems that utilize the T+O-band for short- and medium-range optical communications.

  1. Optical absorption enhancement in a hybrid system photonic crystal - thin substrate for photovoltaic applications.

    Science.gov (United States)

    Buencuerpo, Jeronimo; Munioz-Camuniez, Luis E; Dotor, Maria L; Postigo, Pablo A

    2012-07-02

    A hybrid approach for light trapping using photonic crystal nanostructures (nanorods, nanopillars or nanoholes) on top of an ultra thin film as a substrate is presented. The combination of a nanopatterned layer with a thin substrate shows an enhanced optical absorption than equivalent films without patterning and can compete in performance with nanostructured systems without a substrate. The designs are tested in four relevant materials: amorphous silicon (a-Si), crystalline silicon (Si), gallium arsenide (GaAs) and indium phosphide (InP). A consistent enhancement is observed for all of the materials when using a thin hybrid system (300 nm) even compared to the non patterned thin film with an anti-reflective coating (ARC). A realistic solar cell structure composed of a hybrid system with a layer of indium tin oxide (ITO) an ARC and a back metal layer is performed, showing an 18% of improvement for the nanostructured device.

  2. Theoretical Investigation of Nonlinear Optical Properties of Organic and Transition Metal Hybrid Azobenzene Dendrimers

    Institute of Scientific and Technical Information of China (English)

    LIU Cai-Ping; LIU Ping; WU Ke-Chen

    2008-01-01

    In this work, we report a theoretical exploration of the responses of organic azo-benzene dendrimers. The polarizabilities, the first and second hyperpolarizabilities of the azobenzene monomers (GO), and the first, second and third generation (G1, G2 and G3, respectively) are investigated by semi-empirical methods. The calculated results show that the nonlinear optical (NLO)properties of these organic dendrimers are mainly determined by the azobenzene chromospheres.Additionally, the values of β and γ increase almost in proportion to the number of chromophores. On the other hand, two types of transition metal hybrid azobenzene dendrimers (core-hybrid and branch-end hybrid according to the sites combined with transition metals) are simulated and discussed in detail in the framework of time-dependent density functional theory (TDDFT). The calculated results reveal that the NLO responses of these metal dendrimers distinctly varied as a result of altering the charge transfer transition scale and the excitation energies.

  3. Optical manipulation of a magnon-photon hybrid system

    CERN Document Server

    Braggio, C; Guarise, M; Ortolan, A; Ruoso, G

    2016-01-01

    We demonstrate an all-optical method for manipulating the magnetization in a 1-mm YIG (yttrium-iron-garnet) sphere placed in a $\\sim0.17\\,$T uniform magnetic field. An harmonic of the frequency comb delivered by a multi-GHz infrared laser source is tuned to the Larmor frequency of the YIG sphere to drive magnetization oscillations, which in turn give rise to a radiation field used to thoroughly investigate the phenomenon. The radiation damping issue that occurs at high frequency and in the presence of highly magnetizated materials, has been overcome by exploiting magnon-photon strong coupling regime in microwave cavities. Our findings demonstrate an effective technique for ultrafast control of the magnetization vector in optomagnetic materials via polarization rotation and intensity modulation of an incident laser beam. We eventually get a second-order susceptibility value of $\\sim10^{-7}$ cm$^2$/MW for single crystal YIG.

  4. Integration of optical imaging with a small animal irradiator

    Energy Technology Data Exchange (ETDEWEB)

    Weersink, Robert A., E-mail: robert.weersink@rmp.uhn.on.ca [Radiation Medicine Program, Princess Margaret Hospital, 610 University Avenue, Toronto, Ontario M5G 2M9, Canada and Techna Institute, University Health Network, 124-100 College Street, Toronto, Ontario M5G 1P5 (Canada); Ansell, Steve; Wang, An; Wilson, Graham [Radiation Medicine Program, Princess Margaret Hospital, 610 University Avenue, Toronto, Ontario M5G 2M9 (Canada); Shah, Duoaud [Techna Institute, University Health Network, 124-100 College Street, Toronto, Ontario M5G 1P5 (Canada); Lindsay, Patricia E. [Radiation Medicine Program, Princess Margaret Hospital, 610 University Avenue, Toronto, Ontario M5G 2M9, Canada and Department of Radiation Oncology, University of Toronto, Toronto, Ontario M5S 1A1 (Canada); Jaffray, David A. [Radiation Medicine Program, Princess Margaret Hospital, 610 University Avenue, Toronto, Ontario M5G 2M9 (Canada); Techna Institute, University Health Network, 124-100 College Street, Toronto, Ontario M5G 1P5 (Canada); Department of Radiation Oncology, University of Toronto, Toronto, Ontario M5S 1A1 (Canada); Ontario Cancer Institute, Princess Margaret Hospital, 610 University Avenue, Toronto, Ontario M5G 2M9 (Canada); Department of Medical Biophysics, University of Toronto, Toronto, Ontario M5S 1A1 (Canada)

    2014-10-15

    Purpose: The authors describe the integration of optical imaging with a targeted small animal irradiator device, focusing on design, instrumentation, 2D to 3D image registration, 2D targeting, and the accuracy of recovering and mapping the optical signal to a 3D surface generated from the cone-beam computed tomography (CBCT) imaging. The integration of optical imaging will improve targeting of the radiation treatment and offer longitudinal tracking of tumor response of small animal models treated using the system. Methods: The existing image-guided small animal irradiator consists of a variable kilovolt (peak) x-ray tube mounted opposite an aSi flat panel detector, both mounted on a c-arm gantry. The tube is used for both CBCT imaging and targeted irradiation. The optical component employs a CCD camera perpendicular to the x-ray treatment/imaging axis with a computer controlled filter for spectral decomposition. Multiple optical images can be acquired at any angle as the gantry rotates. The optical to CBCT registration, which uses a standard pinhole camera model, was modeled and tested using phantoms with markers visible in both optical and CBCT images. Optically guided 2D targeting in the anterior/posterior direction was tested on an anthropomorphic mouse phantom with embedded light sources. The accuracy of the mapping of optical signal to the CBCT surface was tested using the same mouse phantom. A surface mesh of the phantom was generated based on the CBCT image and optical intensities projected onto the surface. The measured surface intensity was compared to calculated surface for a point source at the actual source position. The point-source position was also optimized to provide the closest match between measured and calculated intensities, and the distance between the optimized and actual source positions was then calculated. This process was repeated for multiple wavelengths and sources. Results: The optical to CBCT registration error was 0.8 mm. Two

  5. Integration of microcantilevers with photonic structures for mechano-optical wavelength selective devices

    NARCIS (Netherlands)

    Chakkalakkal Abdulla, Shahina Mumthaz

    2011-01-01

    This thesis deals with the fabrication technology and mechano-optical characterisation of compact integrated wavelength selective optical devices for use in telecommunication applications. Upon electrostatic actuation, a mechanical element perturbs the optical evanescent field of a guided wave provi

  6. Hybrid-integrated coherent receiver using silica-based planar lightwave circuit technology

    Science.gov (United States)

    Kim, Jong-Hoi; Choe, Joong-Seon; Choi, Kwang-Seong; Youn, Chun-Ju; Kim, Duk-Jun; Jang, Sun-Hyok; Kwon, Yong-Hwan; Nam, Eun-Soo

    2011-12-01

    A hybrid-integrated coherent receiver module has been achieved using flip-chip bonding technology, consisting of a silica-based 90°-hybrid planar lightwave circuit (PLC) platform, a spot-size converter integrated waveguide photodiode (SSC-WG-PD), and a dual-channel transimpedance amplifier (TIA). The receiver module shows error-free operation up to 40Gb/s and OSNR sensitivity of 11.5 dB for BER = 10-3 at 25 Gb/s.

  7. HYBRID AND INTEGRATED APPROACH TO SHORT TERM LOAD FORECASTING

    Directory of Open Access Journals (Sweden)

    J. P. Rothe,

    2010-12-01

    Full Text Available The forecasting of electricity demand has become one of the major research fields in Electrical Engineering. In recent years, much research has been carried out on the application of artificial intelligence techniques to the Load-Forecasting problem. Various Artificial Intelligence (AI techniques used for load forecasting are Expert systems, Fuzzy, Genetic Algorithm, Artificial Neural Network (ANN. This research work is an attempt to apply hybrid and ntegrated effort to forecast load. Regression, Fuzzy and Neural alongwith Genetic Algorithm will empower the analysts to strongly forecast fairly accurate load demand on hourly base.

  8. A Strip-Loading Optical Waveguide Using Well Poled Stability Organic/Inorganic Hybrid Materials

    Institute of Scientific and Technical Information of China (English)

    GAO Wei-Nan; TIAN Mei-Qiang; SUN Xiao-Qiang; WANG Wei; DENG Ling; GAO Lei; ZHANG Da-Ming

    2009-01-01

    An optical waveguide for a polymer modulator based on organic/inorganic hybrid electro-optic (EO) materials is designed and fabricated by utilizing a strip-loading structure.This hybrid material has a controllable refractive index,high EO coefficient and good poled stability,which are suitable for the EO modulators and switches.The embedded waveguide made of the above EO material can reduce the coupling loss. The light is coupled into the gnided-core layer and then undergoes a transition from the buried waveguide into the EO material.Obvious modulation is observed by application of ac voltage to the EO material.The measured Vπ of co-planar waveguide (CPW) is 5 V for the Mach-Zehnder (MZ) modulator in length of 3.5cm.

  9. Graphene coated fiber optic surface plasmon resonance biosensor for the DNA hybridization detection: Simulation analysis

    Science.gov (United States)

    Shushama, Kamrun Nahar; Rana, Md. Masud; Inum, Reefat; Hossain, Md. Biplob

    2017-01-01

    In this paper, a graphene coated optical fiber surface plasmon resonance (SPR) biosensor is presented for the detection of DNA Hybridization. For the proposed sensor, a four layer model (fiber core /metal /sensing layer /sample) where a sheet of graphene (biomolecular recognition elements (BRE)) acting as a sensing layer is coated around the gold film because graphene enhances the sensitivity of fiber optic SPR biosensor. Numerical analysis shows the variation of resonance wavelength and spectrum of transmitted power for mismatched DNA strands and for complementary DNA strands. For mismatched DNA strands variation is negligible whereas for complementary DNA strands is considerably countable. Proposed sensor successfully distinguishes hybridization and single nucleotide polymorphisms (SNP) by observing the variation level of resonance wavelength and spectrum of transmitted power.

  10. Performance optimization of EDFA-Raman hybrid optical amplifier using genetic algorithm

    Science.gov (United States)

    Singh, Simranjit; Kaler, R. S.

    2015-05-01

    For the first time, a novel net gain analytical model of EDFA-Raman hybrid optical amplifier (HOA) is designed and optimized the various parameters using genetic algorithm. Our method has shown to be robust in the simultaneous analysis of multiple parameters, such as Raman length, EDFA length and its pump powers, to obtained highest possible gain. The optimized HOA is further investigated and characterized on system level in the scenario of 100×10 Gbps dense wavelength division multiplexed (DWDM) system with 25 GHz interval. With an optimized HOA, a flat gain of >18 dB is obtained from frequency region 187 to 189.5 THz with a gain variation of less than 1.35 dB without using any gain flattened technique. The obtained noise figure is also the lowest value (<2 dB/channel) ever reported for proposed hybrid optical amplifier at reduced channel spacing with acceptable bit error rate.

  11. Cost-effective backhaul design using hybrid radio/free-space optical technology

    KAUST Repository

    Douik, Ahmed S.

    2015-06-08

    The deluge of date rate in today\\'s networks poses a cost burden on the backhaul network design. Developing cost efficient backhaul solutions becomes an interesting, yet challenging, problem. Traditional technologies for backhaul networks include either radio-frequency backhauls (RF) or optical fibres (OF). While RF is a cost-effective solution as compared to OF, it supports lower data rate requirements. Another promising backhaul solution that may combine both a high data rate and a relatively low cost is the free-space optics (FSO). FSO, however, is sensitive to nature conditions (e.g., rain, fog, line-ofsight, etc.). A more reliable alternative is, therefore, to combine RF and FSO solutions through a hybrid structure called hybrid RF/FSO. Consider a backhaul network, where the base-stations (BS) can be connected to each other either via OF or hybrid RF/FSO backhaul links. The paper addresses the problem of minimizing the cost of backhaul planning under connectivity and data rates constraints, so as to choose the appropriate costeffective backhaul type between BSs (i.e., either OF or hybrid RF/FSO). The paper solves the problem using graph theory techniques by introducing the corresponding planning graph. It shows that under a specified realistic assumption about the cost of OF and hybrid RF/FSO links, the problem is equivalent to a maximum weight clique problem, which can be solved with moderate complexity. Simulation results show that our proposed solution shows a close-to-optimal performance, especially for practical prices of the hybrid RF/FSO.

  12. Widely tunable second-harmonic generation in a chalcogenide-tellurite hybrid optical fiber.

    Science.gov (United States)

    Cheng, Tonglei; Gao, Weiqing; Kawashima, Hiroyasu; Deng, Dinghuan; Liao, Meisong; Matsumoto, Morio; Misumi, Takashi; Suzuki, Takenobu; Ohishi, Yasutake

    2014-04-01

    When a chalcogenide-tellurite hybrid optical fiber with a high refractive index difference Δn=0.24 is pumped by an optical parametric oscillator with a pump wavelength from 1700 to 3000 nm, widely tunable second-harmonic generation (SHG) from 850 to 1502 nm is obtained. The observation of SHG is primarily due to the surface nonlinearity polarization at the core-cladding interface and the second-harmonic signal remains stable at the maximal level throughout the laser pulse irradiation.

  13. A hybrid fiber-optic sensor system for condition monitoring of large scale wind turbine blades

    Science.gov (United States)

    Kim, Dae-gil; Kim, Hyunjin; Sampath, Umesh; Song, Minho

    2015-07-01

    A hybrid fiber-optic sensor system which combines fiber Bragg grating (FBG) sensors and a Michelson interferometer is suggested for condition monitoring uses of large scale wind turbine blades. The system uses single broadband light source to address both sensors, which simplifies the optical setup and enhances the cost-effectiveness of condition monitoring system. An athermal-packaged FBG is used to supply quasi-coherent light for the Michelson interferometer demodulation. For the feasibility test, different profiles of test strain, temperature and vibration have been applied to test structures, and successfully reconstructed with the proposed sensor system.

  14. Optical and Spectral Studies on β Alanine Metal Halide Hybrid Crystals

    Science.gov (United States)

    Sweetlin, M. Daniel; Selvarajan, P.; Perumal, S.; Ramalingom, S.

    2011-10-01

    We have synthesized and grown β alanine metal halide hybrid crystals viz. β alanine cadmium chloride (BACC), an amino acid transition metal halide complex crystal and β alanine potassium chloride (BAPC), an amino acid alkali metal halide complex crystal by slow evaporation method. The grown crystals were found to be transparent and have well defined morphology. The optical characteristics of the grown crystals were carried out with the help of UV-Vis Spectroscopy. The optical transmittances of the spectrums show that BAPC is more transparent than BACC. The Photoluminescence of the materials were determined by the Photoluminescent Spectroscopy

  15. Synthesis of hybrid chitosan/calcium aluminosilicate using a sol-gel method for optical applications

    Energy Technology Data Exchange (ETDEWEB)

    Elnahrawy, Amany Mohamed [Department of Solid State, Physics Division, National Research Center (NRC), Giza 12622, Cairo (Egypt); Kim, Yong Soo, E-mail: yskim2@ulsan.ac.kr [Department of Physics and Energy Harvest-Storage Research Center (EHSRC), University of Ulsan, Ulsan 44610 (Korea, Republic of); Ali, Ahmed I., E-mail: Ahmed_ali_2010@helwan.edu.eg [Department of Physics and Energy Harvest-Storage Research Center (EHSRC), University of Ulsan, Ulsan 44610 (Korea, Republic of); Basic Science Department, Faculty of Industrial Education & Technology, Helwan University, Cairo 11281 (Egypt)

    2016-08-15

    Hybrid chitosan (CS)/calcium aluminosilicate nanocomposites thin films and membranes were prepared using a sol–gel method with three different concentrations of Al{sub 2}O{sub 3} (5, 7 and 10 mol. %). The prepared nanocomposites were characterized by transmission electron microscopy, X-ray diffraction and Fourier Transform Infrared spectroscopy. The optical properties of the prepared samples were analyzed by UV/Vis spectrophotometry and photoluminescence (PL) spectroscopy. The optical parameters revealed an increase in both the refractive index and band gap of the nanocomposites with increasing Al concentration. In addition, the PL spectra revealed a blue shift that was consistent with an increase in the optical band gap. These results suggest that CS/calcium aluminosilicate in two different forms can be a good candidate for optical sensors applications. - Highlights: • We show a large specific surface area of hybrid CS/calcium aluminosilicate thin films and membranes using sol-gel method. • Inorganic SiO{sub 2}-based phase are perfectly embedded onto chitosan matrix has a reliable stability. • CS/calcium aluminosilicate could be usable for optical sensors, planar waveguide, and bio-sensing.

  16. A Subfemtotesla Atomic Magnetometer Based on Hybrid Optical Pumping of Potassium and Rubidium

    Science.gov (United States)

    Li, Yang; Cai, Hongwei; Ding, Ming; Quan, Wei; Fang, Jiancheng

    2016-05-01

    Atomic magnetometers, based on detection of Larmor spin precession of optically pumped atoms, have been researched and applied extensively. Higher sensitivity and spatial resolution combined with no cryogenic cooling of atomic magnetometers would enable many applications with low cost, including the magnetoencephalography (MEG). Ultrahigh sensitivity atomic magnetometer is considered to be the main development direction for the future. Hybrid optical pumping has been proposed to improve the efficiency of nuclear polarization. But it can also be used for magnetic field measurement. This method can control absorption of optical pumping light, which is benefit for improving the uniformity of alkali metal atoms polarization and the sensitivity of atomic magnetometer. In addition, it allows optical pumping in the absence of quenching gas. We conduct experiments with a hybrid optically pumped atomic magnetometer using a cell containing potassium and rubidium. By adjusting the density ratio of alkali metal and the pumping laser conditions, we measured the magnetic field sensitivity better than 0.7 fT/sqrt(Hz).

  17. Plasmonic nanopatch array for optical integrated circuit applications.

    Science.gov (United States)

    Qu, Shi-Wei; Nie, Zai-Ping

    2013-11-08

    Future plasmonic integrated circuits with the capability of extremely high-speed data processing at optical frequencies will be dominated by the efficient optical emission (excitation) from (of) plasmonic waveguides. Towards this goal, plasmonic nanoantennas, currently a hot topic in the field of plasmonics, have potential to bridge the mismatch between the wave vector of free-space photonics and that of the guided plasmonics. To manipulate light at will, plasmonic nanoantenna arrays will definitely be more efficient than isolated nanoantennas. In this article, the concepts of microwave antenna arrays are applied to efficiently convert plasmonic waves in the plasmonic waveguides into free-space optical waves or vice versa. The proposed plasmonic nanoantenna array, with nanopatch antennas and a coupled wedge plasmon waveguide, can also act as an efficient spectrometer to project different wavelengths into different directions, or as a spatial filter to absorb a specific wavelength at a specified incident angle.

  18. Plasmonic nanopatch array for optical integrated circuit applications

    Science.gov (United States)

    Qu, Shi-Wei; Nie, Zai-Ping

    2013-01-01

    Future plasmonic integrated circuits with the capability of extremely high-speed data processing at optical frequencies will be dominated by the efficient optical emission (excitation) from (of) plasmonic waveguides. Towards this goal, plasmonic nanoantennas, currently a hot topic in the field of plasmonics, have potential to bridge the mismatch between the wave vector of free-space photonics and that of the guided plasmonics. To manipulate light at will, plasmonic nanoantenna arrays will definitely be more efficient than isolated nanoantennas. In this article, the concepts of microwave antenna arrays are applied to efficiently convert plasmonic waves in the plasmonic waveguides into free-space optical waves or vice versa. The proposed plasmonic nanoantenna array, with nanopatch antennas and a coupled wedge plasmon waveguide, can also act as an efficient spectrometer to project different wavelengths into different directions, or as a spatial filter to absorb a specific wavelength at a specified incident angle. PMID:24201454

  19. Integrated Control Plane for IP Enabled Optical Networks

    Institute of Scientific and Technical Information of China (English)

    LIZhengbin; YINHongxi; YUDeming; XUAnshi

    2003-01-01

    With the exponential growth of the Internet traffle for the intense demand for broadband services,providing bandwidth and connectivity on demand has risen to be a hot topic involving establishing connections from client ent systems to another through the optical backbone.So that,control plane and signaling in the optical network seems to be a critical component.This paper proposes and integrated control plane(ICP)and signaling related in IP enabled optical networks.Signaling processing for ensuring dynamic end-to-end lightpath setup has also been presented.Path provisioning comprises a string of operations like service & neighbor discovery,route computation,signaling requests,and path setup.

  20. Integrated Differential Optical Shadow Sensor for Modular Gravitational Reference Sensor

    CERN Document Server

    Zoellner, Andreas; Sun, Ke-Xun

    2013-01-01

    The Laser Interferometer Space Antenna (LISA) is a proposed space mission for the detection of gravitational waves. It consists of three drag-free satellites flying in a triangular constellation. A gravitational reference sensor is used in conjunction with a laser interferometer to measure the distance between test masses inside the three satellites. Other future space mission such as DECIGO and BBO also require a gravitational reference sensor. The Modular Gravitational Reference Sensor (MGRS) is being designed for these purposes and consists of two different optical sensors and a UV LED charge management system. The Differential Optical Shadow Sensor (DOSS) is one of the optical sensors and measures the position of a spherical test mass with respect to the surrounding satellite. This measurement is used for the drag-free feedback control loop. This paper describes the most recent, third generation of the experimental setup for the DOSS that uses a fiber coupled super luminescent LED, an integrated mounting ...

  1. Calculation of two-centre two-electron integrals over Slater-type orbitals revisited. I. Coulomb and hybrid integrals

    CERN Document Server

    Lesiuk, Michał

    2014-01-01

    In this paper, which constitutes the first part of the series, we consider calculation of two-centre Coulomb and hybrid integrals over Slater-type orbitals (STOs). General formulae for these integrals are derived with no restrictions on the values of the quantum numbers and nonlinear parameters. Direct integration over the coordinates of one of the electrons leaves us with the set of overlap-like integrals which are evaluated by using two distinct methods. The first one is based on the transformation to the ellipsoidal coordinates system and the second utilises a recursive scheme for consecutive increase of the angular momenta in the integrand. In both methods simple one-dimensional numerical integrations are used in order to avoid severe digital erosion connected with the straightforward use of the alternative analytical formulae. It is discussed that the numerical integration does not introduce a large computational overhead since the integrands are well-behaved functions, calculated recursively with decent...

  2. Hybrid Level Integration of Biometric Traits for Security Applications

    Directory of Open Access Journals (Sweden)

    Manjunath S Gabasavalagi

    2013-09-01

    Full Text Available In reality the security is to be provided in different levels based on the application and requirement. In attendance related applications require low level security, banking applications may need medium level security and defence applications require high level security. This paper presents a hybrid-modal (Unimodal or Multimodal biometric system which is used to provide better security to applications based on their requirement. Based on the security level, the system uses both single evidence (unimodal for lower level and multiple evidences (multimodal for higher level security. The developed hybrid-modal system employs one or more biometric modalities such as face, voice and fingerprint by alleviating some of the challenges identified in fingerprint, face and voice biometrics modalities. These biometric modalities are selected as they are independent, non-intrusive and robust. Depends on the applications security level requirements like low, medium and high, the number of biometric modalities are provided as evidence to the system. The developed system is tested for 60 users. The accuracy for low level security applications using either fingerprint or face or voice the accuracy of around 94%, 93% and 82% respectively have achieved. The accuracy for medium level security applications using face & fingerprint, face & voice and voice & fingerprint are 91%, 81% and 88% respectively. Further, for high level security using all the three biometric traits the accuracy of 80% is achieved. The developed system provides promising results for all level of security applications.

  3. Guided wave coupling in integrated-optic gratings - Normal incidence

    Science.gov (United States)

    van Roey, J.; Denturck, B.; Lagasse, P. E.

    1984-10-01

    The coupling between the different guided modes of an integrated-optic waveguide grating filter is analyzed. A numerical method based on a finite-difference scheme for the solution of this coupling problem in the case of normal incidence is presented. This allows one to study the influence of the grating profile on the coupling between guided or radiated waves. The exact numerical results are compared with approximate formulas for the coupling coefficient.

  4. Advanced Laser Chemical Processing For Microelectronics and Integrated Optics

    Science.gov (United States)

    1992-08-15

    Barbara, CA (June 25-27, 1990). 15. R.M. Osgood, Jr., " Laser - Fabrication for Integrated Electronics and Optics," OITDA Conference, Tokyo, Japan, (July 5...Society Meeting, Boston, MA, November 26 - December 3, 1990. 20. R.M. Osgood, Jr., "Advances in Laser Fabrication for Solid-State Electronics and...Thin, Excimer Laser-Deposited Cd Interlayers," J. Elec. Mat. 12, 1239 (July, 1990). 14. R.M. Osgood, Jr., " Laser - Fabrication for Solid State

  5. PECASE: All-Optical Photonic Integrated Circuits in Silicon

    Science.gov (United States)

    2011-01-14

    Soltani , and A. Adibi, “High Quality Planar Silicon Nitride Microdisk Resonators for Integrated Photonics in the Visible Wavelength Range,” Optics...contrast, high-Q resonators in chalcogenide glass for sensing,” Opt. Lett. 33, 2500–2502 (2008). [4] B. Momeni, S. Yegnanarayanan, M. Soltani , A. A...lightwave circuits,” J. Lightwave Technol. 17(11), 2032–2038 (1999). [14] B. Momeni, J. Huang, M. Soltani , M. Askari, S. Mohammadi, M. Rakhshandehroo, and

  6. A linear coherent integrated receiver based on a broadband optical phase-locked loop

    Science.gov (United States)

    Ramaswamy, Anand

    Optical Phase-Locked Loops (OPLL) have diverse applications in future communication systems. They can be used in high sensitivity homodyne phase-shift keying receivers for phase noise reduction, provided sufficient loop bandwidth is maintained. Alternative phase-locked loop applications include coherent synchronization of laser arrays and frequency synthesis by offset locking. In this work, a broadband OPLL based coherent receiver is used for linear phase demodulation. Phase modulated (PM) analog optical links have the potential to outperform conventional direct detection links. However, their progress has been stymied by the lack of a linear phase demodulator. We describe how feedback can be used to suppress non-linearities arising from the phase demodulation process. The receiver concept is demonstrated at low frequencies and is found to improve the Spurious Free Dynamic Range (SFDR) of an experimental analog link by over 20dB. In order to extend the operation of the receiver to microwave frequencies, latencies arising from physical delays in the feedback path need to be dramatically reduced. To facilitate this, monolithic and hybrid versions of the receiver based on compact integration of InP photonic integrated circuits (PIC) with InP and SiGe electronic integrated circuits (EIC) have been developed at UCSB. In this work, we develop novel measurement techniques to characterize the linearity of the individual components of the PIC, namely, the semiconductor photodiodes and optical phase modulators. We then demonstrate the operation of the receiver in a high power analog link. The OPLL based receiver has a bandwidth of 1.5GHz. The link gain and shot-noise limited SFDR at 300MHz are -2dB and 125dB-Hz2/3, respectively. Further, optical sampling downconversion is demonstrated as a viable technique to increase the operating frequency of the receiver beyond the baseband range.

  7. A hybrid digital-analog long pulse integrator

    Science.gov (United States)

    Strait, E. J.; Broesch, J. D.; Snider, R. T.; Walker, M. L.

    1997-01-01

    A digital-analog integrator has been developed for use with inductive magnetic sensors in long-pulse tokamaks. Continuous compensation of input offsets is accomplished by alternating analog-to-digital convertor samples from the sensor and a dummy load, while a RC network provides passive integration between samples. Typically a sampling rate of 10 kHz is used. In operational tests on the DIII-D tokamak, digital and analog integration of tokamak data show good agreement. The output drift error during a 1200 s integration interval corresponds to a few percent of the anticipated signal for poloidal field probes in International Thermonuclear Experimental Reactor, and bench tests suggest that the error can be reduced further.

  8. Thin-film perovskites-ferroelectric materials for integrated optics

    Energy Technology Data Exchange (ETDEWEB)

    Walker, F.J. [Univ. of Tennessee, Knoxville, TN (United States)]|[Oak Ridge National Lab., TN (United States); McKee, R.A. [Oak Ridge National Lab., TN (United States)

    1995-12-31

    Optical guided wave (OGW) devices, based on LiNbO{sub 3} or GaAs. are commercially available products with established markets and applications. While LiNbO{sub 3} presently dominates the commercial applications, there are several drivers for the development of improved electro-optic (EO) materials. If the appropriate crystal quality could be obtained for thin-film BaTiO{sub 3} supported on MgO for example, or for an integrated BaTiO{sub 3}/Mg0 structure on silicon or GaAs, then the optimum OGW device structure might be realized. We report on our results for the growth of optical quality, epitaxial BaTiO{sub 3} and SrTiO{sub 3} on single-crystal MgO substrates using source shuttering molecular beam epitaxy (MBE) techniques. We also discuss how these materials can be integrated onto silicon. Our MBE studies show that, for this important class of perovskite oxides, heteroepitaxy between the perovskites and alkaline earth oxides is dominated by interfacial electrostatics at the first atomic layers. We have been able to demonstrate that a layer-by-layer energy minimization associated with interfacial electrostatics leads to the growth of high quality thin films of these materials. We have fabricated waveguides from these materials, and the optical clarity and loss coefficients have been characterized and found to be comparable to in-diffused waveguide structures typically represented by Ti drifted LiNbO{sub 3}.

  9. Hybrid electro-optical stimulation of the rat sciatic nerve induces force generation in the plantarflexor muscles

    Science.gov (United States)

    Duke, Austin R.; Peterson, Erik; Mackanos, Mark A.; Atkinson, James; Tyler, Dustin; Jansen, E. Duco

    2012-12-01

    Objective. Optical methods of neural activation are becoming important tools for the study and treatment of neurological disorders. Infrared nerve stimulation (INS) is an optical technique exhibiting spatially precise activation in the native neural system. While this technique shows great promise, the risk of thermal damage may limit some applications. Combining INS with traditional electrical stimulation, a method known as hybrid electro-optical stimulation, reduces the laser power requirements and mitigates the risk of thermal damage while maintaining spatial selectivity. Here we investigate the capability of inducing force generation in the rat hind limb through hybrid stimulation of the sciatic nerve. Approach. Hybrid stimulation was achieved by combining an optically transparent nerve cuff for electrical stimulation and a diode laser coupled to an optical fiber for infrared stimulation. Force generation in the rat plantarflexor muscles was measured in response to hybrid stimulation with 1 s bursts of pulses at 15 and 20 Hz and with a burst frequency of 0.5 Hz. Main results. Forces were found to increase with successive stimulus trains, ultimately reaching a plateau by the 20th train. Hybrid evoked forces decayed at a rate similar to the rate of thermal diffusion in tissue. Preconditioning the nerve with an optical stimulus resulted in an increase in the force response to both electrical and hybrid stimulation. Histological evaluation showed no signs of thermally induced morphological changes following hybrid stimulation. Our results indicate that an increase in baseline temperature is a likely contributor to hybrid force generation. Significance. Extraneural INS of peripheral nerves at physiologically relevant repetition rates is possible using hybrid electro-optical stimulation.

  10. Ultra-thin silicon/electro-optic polymer hybrid waveguide modulators

    Energy Technology Data Exchange (ETDEWEB)

    Qiu, Feng; Spring, Andrew M. [Institute for Materials Chemistry and Engineering, Kyushu University, 6-1 Kasuga-koen Kasuga, Fukuoka 816-8580 (Japan); Sato, Hiromu [Department of Molecular and Material Sciences, Kyushu University, 6-1 Kasuga-koen Kasuga, Fukuoka 816-8580 (Japan); Maeda, Daisuke; Ozawa, Masa-aki; Odoi, Keisuke [Nissan Chemical Industries, Ltd., 2-10-1 Tuboi Nishi, Funabashi, Chiba 274-8507 (Japan); Aoki, Isao; Otomo, Akira [National Institute of Information and Communications Technology, 588-2 Iwaoka, Nishi-ku, Kobe 651-2492 (Japan); Yokoyama, Shiyoshi, E-mail: s-yokoyama@cm.kyushu-u.ac.jp [Institute for Materials Chemistry and Engineering, Kyushu University, 6-1 Kasuga-koen Kasuga, Fukuoka 816-8580 (Japan); Department of Molecular and Material Sciences, Kyushu University, 6-1 Kasuga-koen Kasuga, Fukuoka 816-8580 (Japan)

    2015-09-21

    Ultra-thin silicon and electro-optic (EO) polymer hybrid waveguide modulators have been designed and fabricated. The waveguide consists of a silicon core with a thickness of 30 nm and a width of 2 μm. The cladding is an EO polymer. Optical mode calculation reveals that 55% of the optical field around the silicon extends into the EO polymer in the TE mode. A Mach-Zehnder interferometer (MZI) modulator was prepared using common coplanar electrodes. The measured half-wave voltage of the MZI with 7 μm spacing and 1.3 cm long electrodes is 4.6 V at 1550 nm. The evaluated EO coefficient is 70 pm/V, which is comparable to that of the bulk EO polymer film. Using ultra-thin silicon is beneficial in order to reduce the side-wall scattering loss, yielding a propagation loss of 4.0 dB/cm. We also investigated a mode converter which couples light from the hybrid EO waveguide into a strip silicon waveguide. The calculation indicates that the coupling loss between these two devices is small enough to exploit the potential fusion of a hybrid EO polymer modulator together with a silicon micro-photonics device.

  11. Optical response of a quantum dot-metal nanoparticle hybrid interacting with a weak probe field.

    Science.gov (United States)

    Kosionis, Spyridon G; Terzis, Andreas F; Sadeghi, Seyed M; Paspalakis, Emmanuel

    2013-01-30

    We study optical effects in a hybrid system composed of a semiconductor quantum dot and a spherical metal nanoparticle that interacts with a weak probe electromagnetic field. We use modified nonlinear density matrix equations for the description of the optical properties of the system and obtain a closed-form expression for the linear susceptibilities of the quantum dot, the metal nanoparticle, and the total system. We then investigate the dependence of the susceptibility on the interparticle distance as well as on the material parameters of the hybrid system. We find that the susceptibility of the quantum dot exhibits optical transparency for specific frequencies. In addition, we show that there is a range of frequencies of the applied field for which the susceptibility of the semiconductor quantum dot leads to gain. This suggests that in such a hybrid system quantum coherence can reverse the course of energy transfer, allowing flow of energy from the metallic nanoparticle to the quantum dot. We also explore the susceptibility of the metal nanoparticle and show that it is strongly influenced by the presence of the quantum dot.

  12. Design of 2*6 optical hybrid in inter-satellite coherent laser communications

    Science.gov (United States)

    Xu, Nan; Liu, Liren; Liu, De'an; Wan, Lingyu; Zhou, Yu

    2008-08-01

    Compared with direct detection, homodyne binary phase shift keying receivers can achieve the best sensitivity theoretically, and became the trend of the research and application in inter-satellite coherent laser communications. In coherent optical communication systems an optical hybrid is an essential component of the receiver. It demodulates the incoming signal by mixing it with the local oscillator. We present a design of a 2*6 optical hybrid. 4 output ports of the hybrid give the narrow mixed beams of the incoming signal and the local oscillator shifted by 90°for communication, and the others give the wide mixed beams with a shifted degree of 180°for position errors detection. CCD captures the interference pattern from the wide beams, and then the pattern is processed and analyzed by the computer. Target position information is obtained from characteristic parameter of the interference pattern. The position errors as the control signals of PAT (pointing, acquisition and tracking) subsystem drive the receiver telescope to keep tracking to the target. The application extends to coherent laser rang finder.

  13. Research progresses of SOI optical waveguide devices and integrated optical switch matrix

    Institute of Scientific and Technical Information of China (English)

    YU Jinzhong; CHEN Shaowu; XIA Jinsong; WANG Zhangtao; FAN Zhongchao; LI Yanping; LIU Jingwei; YANG Di; CHEN Yuanyuan

    2005-01-01

    SOI (silicon-on-insulator) is a new material with a lot of important perform- ances such as large index difference, low transmission loss. Fabrication processes for SOI based optoelectronic devices are compatible with conventional IC processes. Having the potential of OEIC monolithic integration, SOI based optoelectronic devices have shown many good characteristics and become more and more attractive recently. In this paper, the recent progresses of SOI waveguide devices in our research group are presented. By highly effective numerical simulation, the single mode conditions for SOI rib waveguides with rectangular and trapezoidal cross-section were accurately investigated. Using both chemical anisotropic wet etching and plasma dry etching techniques, SOI single mode rib waveguide, MMI coupler, VOA (variable optical attenuator), 2×2 thermal-optical switch were successfully designed and fabricated. Based on these, 4×4 and 8×8 SOI optical waveguide integrated switch matrixes are demonstrated for the first time.

  14. SMART composite high pressure vessels with integrated optical fiber sensors

    Science.gov (United States)

    Blazejewski, Wojciech; Czulak, Andrzej; Gasior, Pawel; Kaleta, Jerzy; Mech, Rafal

    2010-04-01

    In this paper application of integrated Optical Fiber Sensors for strain state monitoring of composite high pressure vessels is presented. The composite tanks find broad application in areas such as: automotive industry, aeronautics, rescue services, etc. In automotive application they are mainly used for gaseous fuels storage (like CNG or compressed Hydrogen). In comparison with standard steel vessels, composite ones have many advantages (i.e. high mechanical strength, significant weight reduction, etc). In the present work a novel technique of vessel manufacturing, according to this construction, was applied. It is called braiding technique, and can be used as an alternative to the winding method. During braiding process, between GFRC layers, two types of optical fiber sensors were installed: point sensors in the form of FBGs as well as interferometric sensors with long measuring arms (SOFO®). Integrated optical fiber sensors create the nervous system of the pressure vessel and are used for its structural health monitoring. OFS register deformation areas and detect construction damages in their early stage (ensure a high safety level for users). Applied sensor system also ensured a possibility of strain state monitoring even during the vessel manufacturing process. However the main application of OFS based monitoring system is to detect defects in the composite structure. An idea of such a SMART vessel with integrated sensor system as well as an algorithm of defect detection was presented.

  15. Optical temperature sensor with enhanced sensitivity by employing hybrid waveguides in a silicon Mach-Zehnder interferometer

    DEFF Research Database (Denmark)

    Guan, Xiaowei; Wang, Xiaoyan; Frandsen, Lars Hagedorn

    2016-01-01

    of the fabricated sensor with silicon/polymer hybrid waveguides is measured to be 172 pm/°C, which is two times larger than a conventional all-silicon optical temperature sensor (∼80 pm/°C). Moreover, a design with silicon/titanium dioxide hybrid waveguides is by calculation expected to have a sensitivity as high...

  16. Studies on 12 V substrate-integrated lead-carbon hybrid ultracapacitors

    Indian Academy of Sciences (India)

    A Banerjee; A K Shukla

    2015-05-01

    A cost-effective 12 V substrate-integrated lead-carbon hybrid ultracapacitor is developed and performance tested. These hybrid ultracapacitors employ flexible-graphite sheets as negative plate currentcollectors that are coated amperometrically with a thin layer of conducting polymer, namely poly-aniline to provide good adhesivity to activated-carbon layer. The positive plate of the hybrid ultracapacitors comprise conventional lead-sheet that is converted electrochemically into a substrate-integrated lead-dioxide electrode. 12 V substrate-integrated lead-carbon hybrid ultracapacitors both in absorbent-glass-mat and polymeric silicagel electrolyte configurations are fabricated and characterized. It is possible to realize 12 V configurations with capacitance values of ∼200 F and ∼300 F, energy densities of ∼1.9 Wh kg−1 and ∼2.5 Wh kg−1 and power densities of ∼2 kW kg−1 and ∼0.8 kW kg−1, respectively, having faradaic-efficiency values of ∼90 % with cycle-life in excess of 100,000 cycles. The effective cost of the mentioned hybrid ultracapacitors is estimated to be about ∼4 US$/Wh as compared to ∼20 US$/Wh for commercially available ultracapacitors.

  17. Optical properties of highly nonlinear silicon-organic hybrid (SOH) waveguide geometries.

    Science.gov (United States)

    Vallaitis, Thomas; Bogatscher, Siegwart; Alloatti, Luca; Dumon, Pieter; Baets, Roel; Scimeca, Michelle L; Biaggio, Ivan; Diederich, François; Koos, Christian; Freude, Wolfgang; Leuthold, Juerg

    2009-09-28

    Geometry, nonlinearity, dispersion and two-photon absorption figure of merit of three basic silicon-organic hybrid waveguide designs are compared. Four-wave mixing and heterodyne pump-probe measurements show that all designs achieve high nonlinearities. The fundamental limitation of two-photon absorption in silicon is overcome using silicon-organic hybrid integration, with a five-fold improvement for the figure of merit (FOM). The value of FOM = 2.19 measured for silicon-compatible nonlinear slot waveguides is the highest value published.

  18. Polarization-dependent losses of integrated optical splitters in glass

    Science.gov (United States)

    Hollenbach, Uwe; Eckstein, Holger; Fabricius, Norbert; Krause, Michael; Kobayashi, Shigeru

    1996-01-01

    During the last two years investments have been made in order to develop new measurement techniques for the characterization of fiber networks. An important characteristic is the neutrality of polarization dependence losses (PDL). Fiber networks contain beside optical sources and detectors a series of basic components like singlemode fibers, integrated optical components (IOC) for the subdistribution, wavelength selective components (WDM) and amplifying elements. The quality of the optical data between transmitters and receivers and the achieved maximum range are determined essentially by the PDL value. In this report the PDL characteristics of passive splitters made by IOT Integrierte Optik GmbH will be described, especially those of N X M splitters. N stands for the entrance port of the splitter and can be 1 or 2. M stands for the exit port of the splitter and can be 2, 4, 8, or 16. Different measuring processes will be described and the achieved measurement results for the PDL will be discussed, In addition to this the different sources of error during the process are described. The achieved results of IOT's N X M splitters have very low PDL values. They are typically smaller than 0.1 dB what makes them excellently suitable for the construction of long-distance optical communication networks. In the meantime such splitters are valued worldwide by different systems suppliers and installed in first optical networks.

  19. SU 8 used as optical waveguide in integrated optical microsensor for biological applications

    Science.gov (United States)

    Műller, Raluca; Obreja, P.; Kusko, M.; Esinenco, D.; Tibeica, C.; Conache, G.; Buia, L.; Apostol, D.; Damian, V.; Mateescu, M.; Diaconu, Mirela; Moldovan, Lucia

    2005-08-01

    We present preliminary experiments for an integrated optical sensor based on a Mach-Zehnder interferometer for biological applications. The sensor is sensitive to refractive index change produced by the presence of a biological species in the cladding of the optical waveguide. A "window" can be patterned in the upper cladding, so that the evanescent wave can be in direct contact with the environmental (the sensitive layer). We investigated as optical waveguides a new material, SU-8, a negative photoresist well known from the development of 3D micromachmed structures. We structured, by photolithographic techniques, rib and channel optical waveguides. We studied the influence of the silicon substrate on propagation losses and the possibility to use these losses for the selective attenuation of the higher order modes on the vertical direction. As biological materials we experimented collagen, which is a bio-polymer which can bind different enzymes or antibodies.

  20. An Integrated Framework for Assessment of Hybrid Water Supply Systems

    Directory of Open Access Journals (Sweden)

    Mukta Sapkota

    2015-12-01

    Full Text Available Urban water managers around the world are adopting decentralized water supply systems, often in combination with centralized systems. While increasing demand for water arising from population growth is one of the primary reasons for this increased adoption of alternative technologies, factors such as climate change, increased frequency of extreme weather events and rapid urbanization also contribute to an increased rate of adoption of these technologies. This combination of centralized-decentralized water systems approach is referred to as “hybrid water supply systems” and is based on the premise that the provision of alternative water sources at local scales can both extend the capacity of existing centralized water supply infrastructures, and improve resilience to variable climatic conditions. It is important to understand, however, that decentralized water production and reuse may change the flow and composition of wastewater and stormwater, thereby potentially also having negative impacts on its effectiveness and performance. This paper describes a framework to assess the interactions between decentralized water supply systems and existing centralized water servicing approaches using several analytical tools, including water balance modelling, contaminant balance modelling and multi-criteria decision analysis. The framework enables the evaluation of impacts due to change in quantity and quality of wastewater and stormwater on the existing centralized system arising from the implementation of hybrid water supply systems. The framework consists of two parts: (1 Physical system analysis for various potential scenarios and (2 Ranking of Scenarios. This paper includes the demonstration of the first part of the framework for an area of Melbourne, Australia by comparing centralized water supply scenario with a combination of centralized water supply and reuse of treated waste water supply scenario.

  1. Optically active substituted polyacetylene@carbon nanotube hybrids: Preparation, characterization and infrared emissivity property study

    Energy Technology Data Exchange (ETDEWEB)

    Bu, Xiaohai; Zhou, Yuming, E-mail: ymzhou@seu.edu.cn; Zhang, Tao; Wang, Yongjuan; Zhang, Zewu; He, Man

    2014-08-15

    Optically active substituted polyacetylene@multiwalled carbon nanotubes (SPA@MWCNTs) nanohybrids were fabricated by wrapping helical SPA copolymers onto the surface of modified nanotubes through ester bonding linkage. SPA copolymer based on chiral phenylalanine and serine was pre-polymerized by a rhodium zwitterion catalyst in THF, and evidently proved to possess strong optical activity and adopt a predominately one-handed helical conformation. Various characterizations including Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and transmission electron microscopy (TEM) demonstrated that the SPA had been covalently grafted onto the nanotubes without destroying their original graphite structure. The wrapped SPA was found to exhibit an enhancement in thermal stability and still maintained considerable optical activity after grafting. The infrared emissivity property of the nanohybrids at 8–14 μm was investigated in addition. The results indicated that the SPA@MWCNTs hybrid matrix could possess a much lower infrared emissivity value (ε=0.707) than raw MWCNTs, which might be due to synergistic effect of the unique helical conformation of optically active SPA and strengthened interfacial interaction between the organic polymers and inorganic nanoparticles. - Graphical abstract: Optically active SPA@MWCNTs nanohybrids with low infrared emissivity. - Highlights: • Synthesis of optically active SPA copolymer derived from serine and phenylalanine. • Preparation and characterization of optically active SPA@MWCNTs nanohybrids. • Application study of the SPA@MWCNTs nanohybrids (ε=0.707) in lowering the infrared emissivity.

  2. Analysis of physical layer performance of hybrid optical-wireless access network

    Science.gov (United States)

    Shaddad, R. Q.; Mohammad, A. B.; Al-hetar, A. M.

    2011-09-01

    The hybrid optical-wireless access network (HOWAN) is a favorable architecture for next generation access network. It is an optimal combination of an optical backhaul and a wireless front-end for an efficient access network. In this paper, the HOWAN architecture is designed based on a wavelengths division multiplexing/time division multiplexing passive optical network (WDM/TDM PON) at the optical backhaul and a wireless fidelity (WiFi) technology at the wireless front-end. The HOWAN is proposed that can provide blanket coverage of broadband and flexible connection for end-users. Most of the existing works, based on performance evaluation are concerned on network layer aspects. This paper reports physical layer performance in terms of the bit error rate (BER), eye diagram, and signal-to-noise ratio (SNR) of the communication system. It accommodates 8 wavelength channels with 32 optical network unit/wireless access points (ONU/APs). It is demonstrated that downstream and upstream of 2 Gb/s can be achieved by optical backhaul for each wavelength channel along optical fiber length of 20 km and a data rate of 54 Mb/s per ONU/AP along a 50 m outdoor wireless link.

  3. Design, construction and integration of hybrid drive components in commercial vehicles. The MAN hybrid drive truck TGL 12.220; Auslegung, Aufbau und Integration von Hybrid-Antriebskomponenten im Nutzfahrzeug. Der MAN Hybrid-Verteiler-Lkw TGL 12.220

    Energy Technology Data Exchange (ETDEWEB)

    Kerschl, Stefan; Hipp, Eberhand; Doebereiner, Rolf [MAN Nutzfahrzeuge AG, Muenchen (Germany)

    2009-07-01

    In contrast to the passenger car the drive train of commercial vehicles is designed basically in view of a maximum efficiency, because the fuel consumption has a determining portion in the vehicle operating expenses of the operators. The pay load of the vehicle also has a high value, in particular in the small and middle segment from 8 t of total weight. In view of pollutant issues the environmental zones which may be also driven by commercial vehicles only from a certain pollutant class were already furnished by many local authority districts. Additional demands for a purely, emission free electric short distance operation can result from suitable emission editions in bigger towns in future. MAN Nutzfahrzeuge AG meet these topical challenges with the development of a hybriddelivery truck of the 12 t - class. At this the aim is to meet to the demands after low CO{sub 2} issue and purely electric operation by a powerful battery system and the recuperation of brake energy. For the integration of the hybrid components in the vehicle it was respected to preserve the pay load of the vehicle without limiting the functionality. The dimensioning of the hybrid drive train for a delivery truck vehicle, the vehicle integration and the effects on the lifecycle economics are lighted up in the following. (orig.)

  4. Wavelength-agile integrated optical transmitters for analog applications

    Science.gov (United States)

    Johansson, Leif A.; Chen, Chin-Hui; Akulova, Yuliya A.; Fish, Gregory A.; Coldren, Larry A.

    2003-12-01

    A summary of current work involving the development of high performance, wavelength-tunable integrated optical transmitters for analog applications is given. The performance of sampled-grating DBR lasers integrated with an SOA and an electroabsorption or Mach-Zehnder modulator is evaluated in terms of E/O conversion efficiency, noise performance and dynamic range. Optimization options to maximize either gain, noise figure or spurious-free dynamic range in analog link applications are discussed. It is shown how the combination of chip-scale integration and the use of bulk waveguide Franz-Keldysh absorption allows coupling of a large optical power level into the electroabsorption modulator, and its effects on the modulation response and analog link performance. Link results on an integrated SGDBR-SOA-EAM device includes a sub-octave SFDR in the 125 to 127 dB/Hz4/5 range and a broadband SFDR of 103-107 dB/Hz2/3 limited by third order intermodulation products or 95-98 dB/Hz1/2, limited by second order intermodulation products, over a 1528 to 1573 nm wavelength range.

  5. Hybridization of Architectural Styles for Integrated Enterprise Information Systems

    Science.gov (United States)

    Bagusyte, Lina; Lupeikiene, Audrone

    Current enterprise systems engineering theory does not provide adequate support for the development of information systems on demand. To say more precisely, it is forming. This chapter proposes the main architectural decisions that underlie the design of integrated enterprise information systems. This chapter argues for the extending service-oriented architecture - for merging it with component-based paradigm at the design stage and using connectors of different architectural styles. The suitability of general-purpose language SysML for the modeling of integrated enterprise information systems architectures is described and arguments pros are presented.

  6. Hybrid microscopy of human carotid atheroma by means of optical-resolution optoacoustic and non-linear optical microscopy

    Science.gov (United States)

    Seeger, Markus; Karlas, Angelos; Soliman, Dominik; Pelisek, Jaroslav; Ntziachristos, Vasilis

    2017-03-01

    Carotid atheromatosis is causally related to stroke, a leading cause of disability and death. We present the analysis of a human carotid atheroma using a novel hybrid microscopy system that combines optical-resolution optoacoustic (photoacoustic) microscopy and several non-linear optical microscopy modalities (second and third harmonic generation, as well as, two-photon excitation fluorescence) to achieve a multimodal examination of the extracted tissue within the same imaging framework. Our system enables the label-free investigation of atheromatous human carotid tissue with a resolution of about 1 μm and allows for the congruent interrogation of plaque morphology and clinically relevant constituents such as red blood cells, collagen, and elastin. Our data reveal mutual interactions between blood embeddings and connective tissue within the atheroma, offering comprehensive insights into its stage of evolution and severity, and potentially facilitating the further development of diagnostic tools, as well as treatment strategies.

  7. Sensitivity of the dispatch strategy in designing grid integrated hybrid energy systems

    OpenAIRE

    Perera, Amarasinghage Tharindu Dasun; Mauree, Dasaraden; Scartezzini, Jean-Louis; Nik, Vahid M.

    2016-01-01

    Integrating renewable energy technologies based on solar PV (SPV) and wind energy in the energy system is challenging due to time dependence of the energy potential for these energy sources. Grid integrated hybrid energy systems combining SPV panels, wind turbines, battery bank and internal combustion generators (ICG) can be used in this regard specially for distributed generation. Energy-economic dispatch strategy plays a vital role in managing the energy flow of the system. However, it is d...

  8. Optical slicing of large scenes by synthetic aperture integral imaging

    Science.gov (United States)

    Navarro, Héctor; Saavedra, Genaro; Molina, Ainhoa; Martínez-Corral, Manuel; Martínez-Cuenca, Raúl; Javidi, Bahram

    2010-04-01

    Integral imaging (InI) technology was created with the aim of providing the binocular observers of monitors, or matrix display devices, with auto-stereoscopic images of 3D scenes. However, along the last few years the inventiveness of researches has allowed to find many other interesting applications of integral imaging. Examples of this are the application of InI in object recognition, the mapping of 3D polarization distributions, or the elimination of occluding signals. One of the most interesting applications of integral imaging is the production of views focused at different depths of the 3D scene. This application is the natural result of the ability of InI to create focal stacks from a single input image. In this contribution we present new algorithm for this optical slicing application, and show that it is possible the 3D reconstruction with improved lateral resolution.

  9. Efficient ethanol recovery from fermentation broths with integrated distillation-vapor permeation hybrid process

    Science.gov (United States)

    The energy demand of distillation-molecular sieve systems for ethanol recovery/dehydration can be significant, particularly for dilute solutions. An alternative hybrid process integrating vapor stripping (like a beer still) with vapor compression and a vapor permeation membrane s...

  10. Hybrid state‐space time integration in a rotating frame of reference

    DEFF Research Database (Denmark)

    Krenk, Steen; Nielsen, Martin Bjerre

    2011-01-01

    A time integration algorithm is developed for the equations of motion of a flexible body in a rotating frame of reference. The equations are formulated in a hybrid state‐space, formed by the local displacement components and the global velocity components. In the spatial discretization the local ...

  11. Efficient ethanol recovery from fermentation broths with integrated distillation-vapor permeation hybrid process

    Science.gov (United States)

    The energy demand of distillation-molecular sieve systems for ethanol recovery/dehydration can be significant, particularly for dilute solutions. An alternative hybrid process integrating vapor stripping (like a beer still) with vapor compression and a vapor permeation membrane s...

  12. Integrated energy & emission management for hybrid electric truck with SCR aftertreatment

    NARCIS (Netherlands)

    Kessels, J.T.B.A.; Willems, F.P.T.; Schoot, W.J.; Bosch, P.P.J. van den

    2010-01-01

    Energy management in hybrid vehicles typically relates to the vehicle powertrain, whereas emission management is associated with the combustion engine and aftertreatment system. To achieve maximum performance in fuel economy and regulated pollutants, the concept of (model-based) Integrated Powertrai

  13. Conceptual Integration of Hybridization by Algerian Students Intending to Teach Physical Sciences

    Science.gov (United States)

    Salah, Hazzi; Dumon, Alain

    2011-01-01

    This work aims to assess the difficulties encountered by students of the Ecole Normale Superieure of Kouba (Algeria) intending to teach physical science in the integration of the hybridization of atomic orbitals. It is a concept that they should use in describing the formation of molecular orbitals ([sigma] and [pi]) in organic chemistry and gaps…

  14. The Hybrid Integrated Circuit of the ALICE Inner Tracking System upgrade

    CERN Document Server

    Fiorenza, G; Pastore, C; Valentino, V

    2016-01-01

    The upgrade of the Inner Tracking System scheduled during the second long shutdown is an important milestone of the ALICE upgrade and it will provide a high improvement of its performances. In this contribution the smallest operator unit of the detector, the Hybrid Integrated Circuits, is presented.

  15. Conceptual Integration of Hybridization by Algerian Students Intending to Teach Physical Sciences

    Science.gov (United States)

    Salah, Hazzi; Dumon, Alain

    2011-01-01

    This work aims to assess the difficulties encountered by students of the Ecole Normale Superieure of Kouba (Algeria) intending to teach physical science in the integration of the hybridization of atomic orbitals. It is a concept that they should use in describing the formation of molecular orbitals ([sigma] and [pi]) in organic chemistry and gaps…

  16. Integrated nanophotonic frequency shifter on the silicon-organic hybrid (SOH) platform for laser vibrometry

    Energy Technology Data Exchange (ETDEWEB)

    Lauermann, M.; Weimann, C.; Palmer, R.; Schindler, P. C. [Institute of Photonics and Quantum Electronics, Karlsruhe Institute of Technology, 76131 Karlsruhe (Germany); Koeber, S.; Freude, W., E-mail: christian.koos@kit.edu; Koos, C., E-mail: christian.koos@kit.edu [Institute of Photonics and Quantum Electronics, Karlsruhe Institute of Technology, 76131 Karlsruhe, Germany and Institute of Microstructure Technology, Karlsruhe Institute of Technology, 76344 Eggenstein-Leopoldshafen (Germany); Rembe, C. [Polytec GmbH, 76337 Waldbronn (Germany)

    2014-05-27

    We demonstrate a waveguide-based frequency shifter on the silicon photonic platform, enabling frequency shifts up to 10 GHz. The device is realized by silicon-organic hybrid (SOH) integration. Temporal shaping of the drive signal allows the suppression of spurious side-modes by more than 23 dB.

  17. A Direct Power Conversion Topology for Grid Integration of Hybrid AC/DC Energy Resources

    DEFF Research Database (Denmark)

    Liu, Xiong; Loh, Poh Chiang; Wang, Peng;

    2013-01-01

    This paper proposes a multiple-input versatile matrix converter (VMC) for integrating hybrid ac/dc energy resources and storages to the power grid. The VMC is developed from the traditional indirect matrix converter but operates in the reverse-boost mode rather than in the forward-buck mode. The ...

  18. A direct power conversion topology for grid integrations of hybrid AC/DC resources

    DEFF Research Database (Denmark)

    Liu, Xiong; Loh, Poh Chiang; Wang, Peng;

    2012-01-01

    This paper proposes a multiple-input versatile matrix converter (VMC) to integrate hybrid ac/dc energy resources and storages to a power grid. The VMC is developed based on the indirect matrix converter (IMC) with its six-switch voltage source converter replaced by a nine-switch topology. The nine...

  19. Double-Slot Hybrid Plasmonic Ring Resonator Used for Optical Sensors and Modulators

    Directory of Open Access Journals (Sweden)

    Xu Sun

    2015-11-01

    Full Text Available An ultra-high sensitivity double-slot hybrid plasmonic (DSHP ring resonator, used for optical sensors and modulators, is developed. Due to high index contrast, as well as plasmonic enhancement, a considerable part of the optical energy is concentrated in the narrow slots between Si and plasmonic materials (silver is used in this paper, which leads to high sensitivity to the infiltrating materials. By partial opening of the outer plasmonic circular sheet of the DSHP ring, a conventional side-coupled silicon on insulator (SOI bus waveguide can be used. Experimental results demonstrate ultra-high sensitivity (687.5 nm/RIU of the developed DSHP ring resonator, which is about five-times higher than for the conventional Si ring with the same geometry. Further discussions show that a very low detection limit (5.37 × 10−6 RIU can be achieved after loaded Q factor modifications. In addition, the plasmonic metal structures offer also the way to process optical and electronic signals along the same hybrid plasmonic circuits with small capacitance (~0.275 fF and large electric field, which leads to possible applications in compact high-efficiency electro-optic modulators, where no extra electrodes for electronic signals are required.

  20. Enhanced Nonlinear Optical Effect in Hybrid Liquid Crystal Cells Based on Photonic Crystal

    Science.gov (United States)

    Bugaychuk, Svitlana; Iljin, Andrey; Lytvynenko, Oleg; Tarakhan, Ludmila; Karachevtseva, Lulmila

    2017-07-01

    Nonlinear-optical response of photorefractive hybrid liquid crystal (LC) cells has been studied by means of dynamic holographic technique in two-wave mixing arrangement. The LC cells include nonuniform silicon substrates comprising a micrometer-range photonic crystal. A thin LC layer is set between silicon substrate and a flat glass substrate covered by a transparent (ITO) electrode. A dynamic diffraction grating was induced in the LC volume by the two-wave mixing of laser beams with simultaneous application of DC electric field to the cell. Theoretical model of Raman-Nath self-diffraction was developed. This model allows for calculation of nonlinear optical characteristics in thin samples on the base of two-wave mixing experimental data, and with taking into account light losses on absorption and/or scattering. The hybrid LC cells demonstrate strong nonlinear optical effect, prospective for many applications in electro-optical microsystems, such as SLMs, as well as in multi-channel systems.

  1. Hybrid Microscopy: Enabling Inexpensive High-Performance Imaging through Combined Physical and Optical Magnifications.

    Science.gov (United States)

    Zhang, Yu Shrike; Chang, Jae-Byum; Alvarez, Mario Moisés; Trujillo-de Santiago, Grissel; Aleman, Julio; Batzaya, Byambaa; Krishnadoss, Vaishali; Ramanujam, Aishwarya Aravamudhan; Kazemzadeh-Narbat, Mehdi; Chen, Fei; Tillberg, Paul W; Dokmeci, Mehmet Remzi; Boyden, Edward S; Khademhosseini, Ali

    2016-03-15

    To date, much effort has been expended on making high-performance microscopes through better instrumentation. Recently, it was discovered that physical magnification of specimens was possible, through a technique called expansion microscopy (ExM), raising the question of whether physical magnification, coupled to inexpensive optics, could together match the performance of high-end optical equipment, at a tiny fraction of the price. Here we show that such "hybrid microscopy" methods--combining physical and optical magnifications--can indeed achieve high performance at low cost. By physically magnifying objects, then imaging them on cheap miniature fluorescence microscopes ("mini-microscopes"), it is possible to image at a resolution comparable to that previously attainable only with benchtop microscopes that present costs orders of magnitude higher. We believe that this unprecedented hybrid technology that combines expansion microscopy, based on physical magnification, and mini-microscopy, relying on conventional optics--a process we refer to as Expansion Mini-Microscopy (ExMM)--is a highly promising alternative method for performing cost-effective, high-resolution imaging of biological samples. With further advancement of the technology, we believe that ExMM will find widespread applications for high-resolution imaging particularly in research and healthcare scenarios in undeveloped countries or remote places.

  2. Integration of thermal photovoltaic hybrid sensors to the building. Final report july 2004. Integrated research project 6.2; Integration de capteurs hybrides photovoltaiques thermiques au bati. Rapport final juillet 2004. Projet de recherche integre 6.2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    The electricity and the heat are two complementary energies necessary for the accommodation. A thermal solar installation needs the electric power for the coolant fluid flow. This research project concerns the optimization of integrated solutions to the building, providing simultaneously these two energies. This document presents the proposed researches programs: analysis of the socio-economic aspects, the physical phenomena knowledge, simulation of the behavior, experimentation, hybrid components integration, simulation of the photovoltaic modules operating and thermal simulation of an electric converter. (A.L.B.)

  3. Lattice design of the integrable optics test accelerator and optical stochastic cooling experiment at Fermilab

    Energy Technology Data Exchange (ETDEWEB)

    Kafka, Gene [Illinois Inst. of Technology, Chicago, IL (United States)

    2015-05-01

    The Integrable Optics Test Accelerator (IOTA) storage ring at Fermilab will serve as the backbone for a broad spectrum of Advanced Accelerator R&D (AARD) experiments, and as such, must be designed with signi cant exibility in mind, but without compromising cost e ciency. The nonlinear experiments at IOTA will include: achievement of a large nonlinear tune shift/spread without degradation of dynamic aperture; suppression of strong lattice resonances; study of stability of nonlinear systems to perturbations; and studies of di erent variants of nonlinear magnet design. The ring optics control has challenging requirements that reach or exceed the present state of the art. The development of a complete self-consistent design of the IOTA ring optics, meeting the demands of all planned AARD experiments, is presented. Of particular interest are the precise control for nonlinear integrable optics experiments and the transverse-to-longitudinal coupling and phase stability for the Optical Stochastic Cooling Experiment (OSC). Since the beam time-of- ight must be tightly controlled in the OSC section, studies of second order corrections in this section are presented.

  4. Ultrabroadband Electro-Optic Modulator Based on Hybrid Silicon-Polymer Dual Vertical Slot Waveguide

    Directory of Open Access Journals (Sweden)

    Shouyuan Shi

    2011-01-01

    Full Text Available We present a novel hybrid silicon-polymer dual slot waveguide for high speed and ultra-low driving voltage electro-optic (EO modulation. The proposed design utilizes the unique properties of ferroelectric materials such as LiNbO3 to achieve dual RF and optical modes within a low index nanoslot. The tight mode concentration and overlap in the slot allow the infiltrated organic EO polymers to experience enhanced nonlinear interaction with the applied electric field. Half-wavelength voltage-length product and electro-optic response are rigorously simulated to characterize the proposed design, which reveals ultrabroadband operation, up to 250 GHz, and subvolt driving voltage for a 1 cm long modulator.

  5. Enhanced hybrid asymmetrically clipped orthogonal frequency division multiplexing for optical wireless communications

    Science.gov (United States)

    Guan, Rui; Huang, Nuo; Wang, Jin-Yuan; Wang, Houyu; Chen, Ming

    2016-05-01

    This paper presents an enhanced hybrid asymmetrically clipped optical orthogonal frequency division multiplexing (EHACO-OFDM) scheme, which benefits from the simultaneous transmission of ACO-OFDM, pulse-amplitude-modulated discrete multitone modulation, and direct-current-biased optical orthogonal frequency division multiplexing (DCO-OFDM). Since the entire available bandwidth is utilized for data modulation, this scheme can achieve higher spectral efficiency than HACO-OFDM and ACO-OFDM. Moreover, as a smaller DC bias is introduced in our scheme, it is more power efficient than asymmetrically clipped DC-biased optical OFDM (ADO-OFDM) and DCO-OFDM. A modified receiver is also designed for this system, taking advantage of an iterative algorithm and a pairwise averaging. It has been shown by simulation that our three-path simultaneous transmission scheme can surpass the existing mixed OFDM-based schemes at high data rates. In addition, compared with the noniterative receiver, the modified receiver exhibits significant gains.

  6. Extraction of linear anisotropic parameters using optical coherence tomography and hybrid Mueller matrix formalism.

    Science.gov (United States)

    Liao, Chia-Chi; Lo, Yu-Lung

    2015-04-20

    A method is proposed for extracting the linear birefringence (LB) and linear dichroism (LD) properties of an anisotropic optical sample using reflection-mode optical coherence tomography (OCT) and a hybrid Mueller matrix formalism. To ensure the accuracy of the extracted parameter values, a method is proposed for calibrating and compensating the polarization distortion effect induced by the beam splitters in the OCT system using a composite quarter-waveplate / half-waveplate / quarter-waveplate structure. The validity of the proposed method is confirmed by extracting the LB and LD properties of a quarter-wave plate and a defective polarizer. To the best of the authors' knowledge, the method proposed in this study represents the first reported attempt to utilize an inverse Mueller matrix formalism and a reflection-mode OCT structure to extract the LB and LD parameters of optically anisotropic samples.

  7. Integrated Quantum Optics: Experiments towards integrated quantum-light sources and quantum-enhanced sensing

    DEFF Research Database (Denmark)

    Hoff, Ulrich Busk

    The work presented in this thesis is focused on experimental application and generation of continuous variable quantum correlated states of light in integrated dielectric structures. Squeezed states are among the most exploited continuous variable optical states for free-space quantum-enhanced se......The work presented in this thesis is focused on experimental application and generation of continuous variable quantum correlated states of light in integrated dielectric structures. Squeezed states are among the most exploited continuous variable optical states for free-space quantum...... in this thesis: Firstly, we present proof-of-principle demonstration of interfacing squeezed light with an on-chip optomechanical resonator, demonstrating a quantum-enhanced sensitivity to the vibrations of the micromechanical object. Secondly, work on developing an integrated source of squeezed light...

  8. Integrated superconducting detectors on semiconductors for quantum optics applications

    Science.gov (United States)

    Kaniber, M.; Flassig, F.; Reithmaier, G.; Gross, R.; Finley, J. J.

    2016-05-01

    Semiconductor quantum photonic circuits can be used to efficiently generate, manipulate, route and exploit nonclassical states of light for distributed photon-based quantum information technologies. In this article, we review our recent achievements on the growth, nanofabrication and integration of high-quality, superconducting niobium nitride thin films on optically active, semiconducting GaAs substrates and their patterning to realize highly efficient and ultra-fast superconducting detectors on semiconductor nanomaterials containing quantum dots. Our state-of-the-art detectors reach external detection quantum efficiencies up to 20 % for ~4 nm thin films and single-photon timing resolutions <72 ps. We discuss the integration of such detectors into quantum dot-loaded, semiconductor ridge waveguides, resulting in the on-chip, time-resolved detection of quantum dot luminescence. Furthermore, a prototype quantum optical circuit is demonstrated that enabled the on-chip generation of resonance fluorescence from an individual InGaAs quantum dot, with a linewidth <15 μeV displaced by 1 mm from the superconducting detector on the very same semiconductor chip. Thus, all key components required for prototype quantum photonic circuits with sources, optical components and detectors on the same chip are reported.

  9. The components of an optical RS flip-flop for an integrated optical processor

    Science.gov (United States)

    Parker, Michael A.; Libby, Stuart I.; Swanson, Paul D.

    1992-07-01

    This report discusses the design, fabrication and test of an optical RS Flip-Flop as an integrated optical memory element. The Flip-Flop has three GaAs-AlGaAs heterostructure lasers with total internal reflection mirrors. A main laser incorporates a saturable absorber to develop the bistable output characteristics. A pump laser bleaches the absorber to set the logic 1 state. A third laser quenches the main laser to reset the device to logic 0. Experiments and data for the laser quenching and bistability are presented.

  10. Hybrid drives for e-bikes - E-management integration; E-management-integration. Serie Hybrid E-Fahrrad-Antrieb

    Energy Technology Data Exchange (ETDEWEB)

    Fuchs, A.

    2005-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) describes work done on a project concerning the further evaluation and improvement of the small-series hybrid drive with the final aim of developing a product. The modular drive system, which can be coupled with components of third party manufacturers, is described. The report deals with practical work done on the subject as well as studies involving investors and the user market. The main results of the project are presented including interesting results on human pedalling effort under load, gear losses and measurements made on hub-motors. Components and energy balances are dealt with. Problems still to be addressed and further work to be done are listed.

  11. Can Integrated Micro-Optical Concentrator Technology Revolutionize Flat-Plate Photovoltaic Solar Energy Harvesting?

    Science.gov (United States)

    Haney, Michael W.

    2015-12-01

    The economies-of-scale and enhanced performance of integrated micro-technologies have repeatedly delivered disruptive market impact. Examples range from microelectronics to displays to lighting. However, integrated micro-scale technologies have yet to be applied in a transformational way to solar photovoltaic panels. The recently announced Micro-scale Optimized Solar-cell Arrays with Integrated Concentration (MOSAIC) program aims to create a new paradigm in solar photovoltaic panel technology based on the incorporation of micro-concentrating photo-voltaic (μ-CPV) cells. As depicted in Figure 1, MOSAIC will integrate arrays of micro-optical concentrating elements and micro-scale PV elements to achieve the same aggregated collection area and high conversion efficiency of a conventional (i.e., macro-scale) CPV approach, but with the low profile and mass, and hopefully cost, of a conventional non-concentrated PV panel. The reduced size and weight, and enhanced wiring complexity, of the MOSAIC approach provide the opportunity to access the high-performance/low-cost region between the conventional CPV and flat-plate (1-sun) PV domains shown in Figure 2. Accessing this portion of the graph in Figure 2 will expand the geographic and market reach of flat-plate PV. This talk reviews the motivation and goals for the MOSAIC program. The diversity of the technical approaches to micro-concentration, embedded solar tracking, and hybrid direct/diffuse solar resource collection found in the MOSAIC portfolio of projects will also be highlighted.

  12. Chemically Integrated Inorganic-Graphene Two-Dimensional Hybrid Materials for Flexible Energy Storage Devices.

    Science.gov (United States)

    Peng, Lele; Zhu, Yue; Li, Hongsen; Yu, Guihua

    2016-12-01

    State-of-the-art energy storage devices are capable of delivering reasonably high energy density (lithium ion batteries) or high power density (supercapacitors). There is an increasing need for these power sources with not only superior electrochemical performance, but also exceptional flexibility. Graphene has come on to the scene and advancements are being made in integration of various electrochemically active compounds onto graphene or its derivatives so as to utilize their flexibility. Many innovative synthesis techniques have led to novel graphene-based hybrid two-dimensional nanostructures. Here, the chemically integrated inorganic-graphene hybrid two-dimensional materials and their applications for energy storage devices are examined. First, the synthesis and characterization of different kinds of inorganic-graphene hybrid nanostructures are summarized, and then the most relevant applications of inorganic-graphene hybrid materials in flexible energy storage devices are reviewed. The general design rules of using graphene-based hybrid 2D materials for energy storage devices and their current limitations and future potential to advance energy storage technologies are also discussed.

  13. Integrated Optical Interferometers with Micromachined Diaphragms for Pressure Sensing

    Science.gov (United States)

    DeBrabander, Gregory N.; Boyd, Joseph T.

    1996-01-01

    Optical pressure sensors have been fabricated which use an integrated optical channel waveguide that is part of an interferometer to measure the pressure-induced strain in a micromachined silicon diaphragm. A silicon substrate is etched from the back of the wafer leaving a rectangular diaphragm. On the opposite side of the wafer, ring resonator and Mach-Zehnder interferometers are formed with optical channel waveguides made from a low pressure chemical vapor deposited film of silicon oxynitride. The interferometer's phase is altered by pressure-induced stress in a channel segment positioned over the long edge of the diaphragm. The phase change in the ring resonator is monitored using a link-insensitive swept frequency laser diode, while in the Mach-Zehnder it is determined using a broad band super luminescent diode with subsequent wavelength separation. The ring resonator was found to be highly temperature sensitive, while the Mach-Zehnder, which had a smaller optical path length difference, was proportionally less so. The quasi-TM mode was more sensitive to pressure, in accord with calculations. Waveguide and sensor theory, sensitivity calculations, a fabrication sequence, and experimental results are presented.

  14. Vibrational and optical spectroscopies integrated with environmental transmission electron microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Picher, Matthieu; Mazzucco, Stefano [Center for Nanoscale Science and Technology, National Institute of Standards and Technology, Gaithersburg, MD 20899-6203 (United States); Institute for Research in Electronics and Applied Physics, University of Maryland, College Park, MD 20740 (United States); Blankenship, Steve [Center for Nanoscale Science and Technology, National Institute of Standards and Technology, Gaithersburg, MD 20899-6203 (United States); Sharma, Renu, E-mail: renu.sharma@nist.gov [Center for Nanoscale Science and Technology, National Institute of Standards and Technology, Gaithersburg, MD 20899-6203 (United States)

    2015-03-15

    Here, we present a measurement platform for collecting multiple types of spectroscopy data during high-resolution environmental transmission electron microscopy observations of dynamic processes. Such coupled measurements are made possible by a broadband, high-efficiency, free-space optical system. The critical element of the system is a parabolic mirror, inserted using an independent hollow rod and placed below the sample holder which can focus a light on the sample and/or collect the optical response. We demonstrate the versatility of this optical setup by using it to combine in situ atomic-scale electron microscopy observations with Raman spectroscopy. The Raman data is also used to measure the local temperature of the observed sample area. Other applications include, but are not limited to: cathodo- and photoluminescence spectroscopy, and use of the laser as a local, high-rate heating source. - Highlights: • Broadband, high-efficiency design adaptable to other electron microscopes. • Raman spectroscopy integrated with environmental transmission electron microscopy. • Raman spectra peak frequency shifts enable measurement of local sample temperature. • Multiple types of optical spectroscopy enabled, e.g. cathodoluminescence.

  15. Improvement of matrix condition of Hybrid, space variant optics by the means of parallel optics design.

    Science.gov (United States)

    Klapp, Iftach; Mendlovic, David

    2009-07-06

    The problem of image restoration of space variant blur is common and important. One of the most useful descriptions of this problem is in its algebraic form I=H*O, where O is the object represented as a column vector, I is the blur image represented as a column vector and H is the PSF matrix that represents the optical system. When inverting the problem to restore the geometric object from the blurred image and the known system matrix, restoration is limited in speed and quality by the system condition. Current optical design methods focus on image quality, therefore if additional image processing is needed the matrix condition is taken "as is". In this paper we would like to present a new optical approach which aims to improve the system condition by proper optical design. In this new method we use Singular Value Decomposition (SVD) to define the weak parts of the matrix condition. We design a second optical system based on those weak SVD parts and then we add the second system parallel to the first one. The original and second systems together work as an improved parallel optics system. Following that, we present a method for designing such a "parallel filter" for systems with a spread SVD pattern. Finally we present a study case in which by using our new method we improve a space variant image system with an initial condition number of 8.76e4, down to a condition number of 2.29e3. We use matrix inversion to simulate image restoration. Results show that the new parallel optics immunity to Additive White Gaussian Noise (AWGN) is much better then that of the original simple lens. Comparing the original and the parallel optics systems, the parallel optics system crosses the MSEIF=0 [db] limit in SNR value which is more than 50db lower then the SNR value in the case of the original simple lens. The new parallel optics system performance is also compared to another method based on the MTF approach.

  16. Sticker-type ECG/PPG concurrent monitoring system hybrid integration of CMOS SoC and organic sensor device.

    Science.gov (United States)

    Lee, Yongsu; Lee, Hyeonwoo; Yoo, Seunghyup; Yoo, Hoi-Jun; Yongsu Lee; Hyeonwoo Lee; Seunghyup Yoo; Hoi-Jun Yoo; Yoo, Seunghyup; Lee, Yongsu; Yoo, Hoi-Jun; Lee, Hyeonwoo

    2016-08-01

    The sticker-type sensor system is proposed targeting ECG/PPG concurrent monitoring for cardiovascular diseases. The stickers are composed of two types: Hub and Sensor-node (SN) sticker. Low-power CMOS SoC for measuring ECG and PPG signal is hybrid integrated with organic light emitting diodes (OLEDs) and organic photo detector (OPD). The sticker has only 2g weight and only consumes 141μW. The optical calibration loop is adopted for maintaining SNR of PPG signal higher than 30dB. The pulse arrival time (PAT) and SpO2 value can be extracted from various body parts and verified comparing with the reference device from 20 people in-vivo experiments.

  17. Domain-dependent electronic structure and optical absorption property in hybrid organic-inorganic perovskite.

    Science.gov (United States)

    Meng, Xiang; Zhang, Ruifeng; Fu, Zhongheng; Zhang, Qianfan

    2016-10-05

    Hybrid organic-inorganic perovskites, represented by materials in the CH3NH3PbI3 series, have become one of the most promising materials for solar cells with a high power conversion efficiency and low cost. The ordered Pb-I cage in such hybrid perovskites can induce the polarized cations to form a variety of polarization domains with long-range order, which will lead to the formation of specific atomic conformations or metastable crystalline phases, unique electronic band structures and optical absorption properties. Such domain-dependent characteristics play a critical role in the phase transition and service stability of such solar cells, and also open up the opportunity of tuning their electronic structure. In the present study, we systematically investigate the band structures and optical absorption properties of different electronically ordered domains in CH3NH3PbI3. By comparing different perovskites containing various cations, we have clarified the important influence of cation polarization on domain-dependent properties. Our results provide not only a possible pathway for the manipulation of band structure by applying an external field, but also a novel scheme for improving the performance and stability of hybrid perovskites.

  18. Resilient backhaul network design using hybrid radio/free-space optical technology

    KAUST Repository

    Douik, Ahmed

    2016-07-26

    The radio-frequency (RF) technology is a scalable solution for the backhaul planning. However, its performance is limited in terms of data rate and latency. Free Space Optical (FSO) backhaul, on the other hand, offers a higher data rate but is sensitive to weather conditions. To combine the advantages of RF and FSO backhauls, this paper proposes a cost-efficient backhaul network using the hybrid RF/FSO technology. To ensure a resilient backhaul, the paper imposes a given degree of redundancy by connecting each node through K link-disjoint paths so as to cope with potential link failures. Hence, the network planning problem considered in this paper is the one of minimizing the total deployment cost by choosing the appropriate link type, i.e., either hybrid RF/FSO or optical fiber (OF), between each couple of base-stations while guaranteeing K link-disjoint connections, a data rate target, and a reliability threshold. The paper solves the problem using graph theory techniques. It reformulates the problem as a maximum weight clique problem in the planning graph, under a specified realistic assumption about the cost of OF and hybrid RF/FSO links. Simulation results show the cost of the different planning and suggest that the proposed heuristic solution has a close-to-optimal performance for a significant gain in computation complexity. © 2016 IEEE.

  19. Nonlinear random optical waves: Integrable turbulence, rogue waves and intermittency

    Science.gov (United States)

    Randoux, Stéphane; Walczak, Pierre; Onorato, Miguel; Suret, Pierre

    2016-10-01

    We examine the general question of statistical changes experienced by ensembles of nonlinear random waves propagating in systems ruled by integrable equations. In our study that enters within the framework of integrable turbulence, we specifically focus on optical fiber systems accurately described by the integrable one-dimensional nonlinear Schrödinger equation. We consider random complex fields having a Gaussian statistics and an infinite extension at initial stage. We use numerical simulations with periodic boundary conditions and optical fiber experiments to investigate spectral and statistical changes experienced by nonlinear waves in focusing and in defocusing propagation regimes. As a result of nonlinear propagation, the power spectrum of the random wave broadens and takes exponential wings both in focusing and in defocusing regimes. Heavy-tailed deviations from Gaussian statistics are observed in focusing regime while low-tailed deviations from Gaussian statistics are observed in defocusing regime. After some transient evolution, the wave system is found to exhibit a statistically stationary state in which neither the probability density function of the wave field nor the spectrum changes with the evolution variable. Separating fluctuations of small scale from fluctuations of large scale both in focusing and defocusing regimes, we reveal the phenomenon of intermittency; i.e., small scales are characterized by large heavy-tailed deviations from Gaussian statistics, while the large ones are almost Gaussian.

  20. Stabilization and Frequency Control of a DFB Laser With a Tunable Optical Reflector Integrated in a Silicon Photonics PIC

    Science.gov (United States)

    Hauck, Johannes; Schrammen, Matthias; Romero-Garcia, Sebastian; Muller, Juliana; Shen, Bin; Richter, Jens; Merget, Florian; Witzens, Jeremy

    2016-12-01

    We investigate the effect of tunable optical feedback on a commercial DFB laser edge coupled to a Silicon Photonics planar integrated circuit in which a tunable reflector has been implemented by means of a ring resonator based add-drop multiplexer. Controlled optical feedback allows for fine-tuning of the laser oscillation frequency. Under certain conditions it also allows suppression of bifurcation modes triggered by reflections occurring elsewhere on the chip. A semi-analytical model describing laser dynamics under combined optical feedback from the input facet of the edge coupler and from the tunable on-chip reflector fits the measurements. Compensation of detrimental effects from reflections induced elsewhere on a transceiver chip may allow moving isolators downstream in future communications systems, facilitating direct hybrid laser integration in Silicon Photonics chips, provided a suitable feedback signal for a control system can be identified. Moreover, the optical frequency tuning at lower feedback levels can be used to form a rapidly tunable optical oscillator as part of an optical phase locked loop, circumventing the problem of the thermal to free carrier effect crossover in the FM response of injection current controlled semiconductor laser diodes.

  1. Low-cost RAU with Optical Power Supply Used in a Hybrid RoF IEEE 802.11 Network

    Science.gov (United States)

    Kowalczyk, M.; Siuzdak, J.

    2014-09-01

    The paper presents design and implementation of a low-cost RAU (Remote Antenna Unit) device. It was designed to work in a hybrid Wi-Fi/optical network based on the IEEE 802.11b/g standard. An unique feature of the device is the possibility of optical power supply.

  2. 100 Gbit/s hybrid optical fiber-wireless link in the W-band (75-110 GHz).

    Science.gov (United States)

    Pang, Xiaodan; Caballero, Antonio; Dogadaev, Anton; Arlunno, Valeria; Borkowski, Robert; Pedersen, Jesper S; Deng, Lei; Karinou, Fotini; Roubeau, Fabien; Zibar, Darko; Yu, Xianbin; Monroy, Idelfonso Tafur

    2011-12-05

    We experimentally demonstrate an 100 Gbit/s hybrid optical fiber-wireless link by employing photonic heterodyning up-conversion of optical 12.5 Gbaud polarization multiplexed 16-QAM baseband signal with two free running lasers. Bit-error-rate performance below the FEC limit is successfully achieved for air transmission distances up to 120 cm.

  3. 100 Gbit/s hybrid optical fiber-wireless link in the W-band (75–110 GHz)

    DEFF Research Database (Denmark)

    Pang, Xiaodan; Caballero Jambrina, Antonio; Dogadaev, Anton Konstantinovich;

    2011-01-01

    We experimentally demonstrate an 100 Gbit/s hybrid optical fiber-wireless link by employing photonic heterodyning up-conversion of optical 12.5 Gbaud polarization multiplexed 16-QAM baseband signal with two free running lasers. Bit-error-rate performance below the FEC limit is successfully achieved...

  4. Optical fiber LPG biosensor integrated microfluidic chip for ultrasensitive glucose detection.

    Science.gov (United States)

    Yin, Ming-Jie; Huang, Bobo; Gao, Shaorui; Zhang, A Ping; Ye, Xuesong

    2016-05-01

    An optical fiber sensor integrated microfluidic chip is presented for ultrasensitive detection of glucose. A long-period grating (LPG) inscribed in a small-diameter single-mode fiber (SDSMF) is employed as an optical refractive-index (RI) sensor. With the layer-by-layer (LbL) self-assembly technique, poly (ethylenimine) (PEI) and poly (acrylic acid) (PAA) multilayer film is deposited on the SDSMF-LPG sensor for both supporting and signal enhancement, and then a glucose oxidase (GOD) layer is immobilized on the outer layer for glucose sensing. A microfluidic chip for glucose detection is fabricated after embedding the SDSMF-LPG biosensor into the microchannel of the chip. Experimental results reveal that the SDSMF-LPG biosensor based on such a hybrid sensing film can ultrasensitively detect glucose concentration as low as 1 nM. After integration into the microfluidic chip, the detection range of the sensor is extended from 2 µM to 10 µM, and the response time is remarkablely shortened from 6 minutes to 70 seconds.

  5. Throughput Improvement In Wireless Mesh Networks By Integrating With Optical Network

    Directory of Open Access Journals (Sweden)

    Chakrapani gadde

    2012-06-01

    Full Text Available In the last decade wireless mesh networks (WMNs have emerged as a key technology for next generation wireless networking. Because of their advantages over other wireless networks, WMNs are undergoing rapid progress and inspiring numerous applications. One such application is to provide peer-to-peer communication for all the users who are distributed over some area. Since the users are connected in awireless multi-hop passion complete ubiquity is provided. But as the number of users accessing the network is increasing there could be a chance of experiencing more interference by each user due to the communication link of every other user. So in a wireless mesh network as the load increases the throughput of network is going to be decreased due to wireless interference by other users. To sustain this problem we are going to integrate the WMN with passive optical network (PON. The resulting hybrid network (Optical-wireless network could reduce the wireless hops of each user, so that we can reduce the total wireless interference experienced by each user resulting in improved network throughput. This paper aims to study the network throughput gain in Optical-wireless network subject to peer-to-peer communications.

  6. Optical 40 GHz pulse source module based on a monolithically integrated mode locked DBR laser

    Science.gov (United States)

    Huettl, B.; Kaiser, R.; Kroh, M.; Schubert, C.; Jacumeit, G.; Heidrich, H.

    2005-11-01

    In this paper the performance characteristics of compact optical 40 GHz pulse laser modules consisting of a monolithic mode-locked MQW DBR laser on GaInAsP/InP are reported. The monolithic devices were fabricated as tunable multi-section buried heterostructure lasers. A DBR grating is integrated at the output port of an extended cavity in order to meet the standardized ITU wavelength channels allocated in the spectral window around 1.55 μm in optical high speed communication networks. The fabricated 40 GHz lasers modules not only emit short optical pulses (< 1.5 ps) with very low amplitude noise (<1.5 %) and phase noise levels (timing jitter: 50 fs) but also enable good pulse-to-pulse phase and long-term stability. A wavelength tuning range of 6 nm is possible and large locking bandwidths between 100 ... 260 MHz are observed. All data have been achieved by operating the lasers in a hybrid mode-locking scheme with a required minimum micro-wave power of only 12 dBm for pulse synchronization. Details on laser chip architecture and module performance are summarized and the results of a stable and error free module performance in first 160 Gb/s (4 x 40 Gb/s OTDM) RZ-DPSK transmission experiments are presented.

  7. Hybrid routing and spectrum assignment algorithms based on distance-adaptation combined coevolution and heuristics in elastic optical networks

    Science.gov (United States)

    Ding, Zhe; Xu, Zhanqi; Zeng, Xiaodong; Ma, Tao; Yang, Fan

    2014-04-01

    By adopting the orthogonal frequency division multiplexing technology, spectrum-sliced elastic optical path networks can offer flexible bandwidth to each connection request and utilize the spectrum resources efficiently. The routing and spectrum assignment (RSA) problems in SLICE networks are solved by using heuristic algorithms in most prior studies and addressed by intelligent algorithms in few investigations. The performance of RSA algorithms can be further improved if we could combine such two types of algorithms. Therefore, we propose three hybrid RSA algorithms: DACE-GMSF, DACE-GLPF, and DACE-GEMkPSF, which are the combination of the heuristic algorithm and coevolution based on distance-adaptive policy. In the proposed algorithms, we first groom the connection requests, then sort the connection requests by using the heuristic algorithm (most subcarriers first, longest path first, and extended most k paths' slots first), and finally search the approximately optimal solution with the coevolutionary policy. We present a model of the RSA problem by using integral linear programming, and key elements in the proposed algorithms are addressed in detail. Simulations under three topologies show that the proposed hybrid RSA algorithms can save spectrum resources efficiently.

  8. Integrated optical waveguide sensor for lighting impulse electric field measurement

    Science.gov (United States)

    Zhang, Jiahong; Chen, Fushen; Sun, Bao; Chen, Kaixin

    2014-09-01

    A Lithium niobate (LiNbO3) based integrated optical E-field sensor with an optical waveguide Mach-Zehnder interferometer (MZI) and a tapered antenna has been designed and fabricated for the measurement of the pulsed electric field. The minimum detectable E-field of the sensor was 10 kV/m. The sensor showed a good linear characteristic while the input E-fields varied from 10 kV/m to 370 kV/m. Furthermore, the maximum detectable E-field of the sensor, which could be calculated from the sensor input/output characteristic, was approximately equal to 1000 kV/m. All these results suggest that such sensor can be used for the measurement of the lighting impulse electric field.

  9. All-optical phase modulation for integrated interferometric biosensors.

    Science.gov (United States)

    Dante, Stefania; Duval, Daphné; Sepúlveda, Borja; González-Guerrero, Ana Belen; Sendra, José Ramón; Lechuga, Laura M

    2012-03-26

    We present the theoretical and the experimental implementation of an all-optical phase modulation system in integrated Mach-Zehnder Interferometers to solve the drawbacks related to the periodic nature of the interferometric signal. Sensor phase is tuned by modulating the emission wavelength of low-cost commercial laser diodes by changing their output power. FFT deconvolution of the signal allows for direct phase readout, immune to sensitivity variations and to light intensity fluctuations. This simple phase modulation scheme increases the signal-to-noise ratio of the measurements in one order of magnitude, rendering in a sensor with a detection limit of 1.9·10⁻⁷ RIU. The viability of the all-optical modulation approach is demonstrated with an immunoassay detection as a biosensing proof of concept.

  10. INVESTIGATION ON HYBRID WDM (DWDM+CWDM FREE SPACE OPTICAL COMMUNICATION SYSTEM

    Directory of Open Access Journals (Sweden)

    S. Robinson

    2015-12-01

    Full Text Available Free Space Optical (FSO communication is being realized as an effective solution for future accessing networks, offering light passed through air. The performance of FSO can be primarily degraded by various atmospheric attenuation namely, rain, fog, haze and snow. At present, hybridization of Dense Wavelength Division Multiplexing (DWDM with Coarse Wavelength Division Multiplexing (CWDM becomes necessary to scale the speed and high bandwidth of the services. In this paper, hybrid WDM system is proposed, designed and the network parameters such as Bit Error Rate (BER, Quality Factor and receiver sensitivity are analyzed with respect to link distance for various weather conditions. For investigation, 4 CWDM and 8 DWDM channels are considered whose corresponding channel spacing is 20nm and 0.8nm, respectively. From the simulation, it is investigated that the average link distance of proposed hybrid WDM-FSO system for DWDM and CWDM system at very clear condition are around 810km and 780km. The proposed hybrid WDM based FSO system is designed to handle the quality of transmission for 12 users, each at a data rate of 2.5Gbps.

  11. Hybrid Finite Element and Volume Integral Methods for Scattering Using Parametric Geometry

    DEFF Research Database (Denmark)

    Volakis, John L.; Sertel, Kubilay; Jørgensen, Erik

    2004-01-01

    n this paper we address several topics relating to the development and implementation of volume integral and hybrid finite element methods for electromagnetic modeling. Comparisons of volume integral equation formulations with the finite element-boundary integral method are given in terms of accu...... of vanishing divergence within the element but non-zero curl. In addition, a new domain decomposition is introduced for solving array problems involving several million degrees of freedom. Three orders of magnitude CPU reduction is demonstrated for such applications....

  12. Hybrid silicon evanescent devices

    Directory of Open Access Journals (Sweden)

    Alexander W. Fang

    2007-07-01

    Full Text Available Si photonics as an integration platform has recently been a focus of optoelectronics research because of the promise of low-cost manufacturing based on the ubiquitous electronics fabrication infrastructure. The key challenge for Si photonic systems is the realization of compact, electrically driven optical gain elements. We review our recent developments in hybrid Si evanescent devices. We have demonstrated electrically pumped lasers, amplifiers, and photodetectors that can provide a low-cost, scalable solution for hybrid integration on a Si platform by using a novel hybrid waveguide architecture, consisting of III-V quantum wells bonded to Si waveguides.

  13. Development of an optically pumped atomic magnetometer using a K-Rb hybrid cell and its application to magnetocardiography

    Directory of Open Access Journals (Sweden)

    Yosuke Ito

    2012-09-01

    Full Text Available We have developed an optically pumped atomic magnetometer using a hybrid cell of K and Rb. The hybrid optical pumping technique can apply dense alkali-metal vapor to the sensor head and leads to high signal intensity. We use dense Rb vapor as probed atoms, and achieve a sensitivity of approximately 100 fTrms/Hz1/2 around 10 Hz. In this case, the sensitivity is limited by the system noise, and the magnetic linewidth is narrower than that for direct Rb optical pumping. We demonstrated magnetocardiography using the magnetometer and obtained clear human magnetocardiograms.

  14. An optical FSK transmitter based on an integrated DFB laser-EA modulator and its application in optical labeling

    DEFF Research Database (Denmark)

    Zhang, Jianfeng; Chi, Nan; Holm-Nielsen, Pablo Villanueva;

    2003-01-01

    An optical frequency-shift-keying (FSK) transmitter based on an integrated distributed feedback laser-electroabsorption modulator is proposed and demonstrated. The feasibility of its application in optical labeling is also validated by the experimental results. The generated optical signal, consi...

  15. Ex vivo imaging of human thyroid pathology using integrated optical coherence tomography and optical coherence microscopy

    Science.gov (United States)

    Zhou, Chao; Wang, Yihong; Aguirre, Aaron D.; Tsai, Tsung-Han; Cohen, David W.; Connolly, James L.; Fujimoto, James G.

    2010-01-01

    We evaluate the feasibility of optical coherence tomography (OCT) and optical coherence microscopy (OCM) for imaging of benign and malignant thyroid lesions ex vivo using intrinsic optical contrast. 34 thyroid gland specimens are imaged from 17 patients, covering a spectrum of pathology ranging from normal thyroid to benign disease/neoplasms (multinodular colloid goiter, Hashimoto's thyroiditis, and follicular adenoma) and malignant thyroid tumors (papillary carcinoma and medullary carcinoma). Imaging is performed using an integrated OCT and OCM system, with sections. Characteristic features that suggest malignant lesions, such as complex papillary architecture, microfollicules, psammomatous calcifications, or replacement of normal follicular architecture with sheets/nests of tumor cells, can be identified from OCT and OCM images and are clearly differentiable from normal or benign thyroid tissues. With further development of needle-based imaging probes, OCT and OCM could be promising techniques to use for the screening of thyroid nodules and to improve the diagnostic specificity of fine needle aspiration evaluation.

  16. Integrated optical electric field sensor with telescopic dipole

    Institute of Scientific and Technical Information of China (English)

    Bao Sun; Fushen Chen; Yongjun Yang

    2008-01-01

    An integrated optical electric field sensor based on a Mach-Zehnder interferometer with the telescopic dipole is designed and fabricated, and its electrodes are segmented and connected with a telescopic dipole.The measured results show that when the frequency response is from 10kHz to 6GHz with the antenna length of 55mm, the minimum detectable electric field of 20mV/m can be obtained, and the linear dynamics range can reach 90dB at 250MHz.

  17. Integrable nonlinear parity-time symmetric optical oscillator

    CERN Document Server

    Hassan, Absar U; Miri, Mohammad-Ali; Khajavikhan, Mercedeh; Christodoulides, Demetrios N

    2016-01-01

    The nonlinear dynamics of a balanced parity-time symmetric optical microring arrangement are analytically investigated. By considering gain and loss saturation effects, the pertinent conservation laws are explicitly obtained in the Stokes domain-thus establishing integrability. Our analysis indicates the existence of two regimes of oscillatory dynamics and frequency locking, both of which are analogous to those expected in linear parity-time symmetric systems. Unlike other saturable parity time symmetric systems considered before, the model studied in this work first operates in the symmetric regime and then enters the broken parity-time phase.

  18. Development and fabrication of monolithically integrated optical packet switches

    Science.gov (United States)

    Yanson, Dan A.; Silver, Mark; Vassalli, Omar; Campbell, Margaret; Masterton, Graeme; McDougall, Stewart D.; Marsh, John H.

    2007-02-01

    We report development activities towards realization of fully integrated 1x2, 2x2, and 4x4 cross-point optical switches for WDM-packet-based data networking. Two enabling technologies, quantum-well intermixing and etched turning mirrors, are developed and demonstrated in InGaAs/InAlGaAs InP-based material at a wavelength of 1.55 μm. We describe the use of both technologies to fabricate switch chips with different port counts.

  19. All-optical delay technique for supporting multiple antennas in a hybrid optical - wireless transmission system

    DEFF Research Database (Denmark)

    Prince, Kamau; Chiuchiarelli, A; Presi, M

    2008-01-01

    We introduce a novel continuously-variable optical delay technique to support beam-forming wireless communications systems using antenna arrays. We demonstrate delay with 64-QAM modulated signals at a rate of 15 Msymbol/sec with 2.5 GHz carrier frequency.......We introduce a novel continuously-variable optical delay technique to support beam-forming wireless communications systems using antenna arrays. We demonstrate delay with 64-QAM modulated signals at a rate of 15 Msymbol/sec with 2.5 GHz carrier frequency....

  20. Optical stretching of giant unilamellar vesicles with an integrated dual-beam optical trap.

    Science.gov (United States)

    Solmaz, Mehmet E; Biswas, Roshni; Sankhagowit, Shalene; Thompson, James R; Mejia, Camilo A; Malmstadt, Noah; Povinelli, Michelle L

    2012-10-01

    We have integrated a dual-beam optical trap into a microfluidic platform and used it to study membrane mechanics in giant unilamellar vesicles (GUVs). We demonstrate the trapping and stretching of GUVs and characterize the membrane response to a step stress. We then measure area strain as a function of applied stress to extract the bending modulus of the lipid bilayer in the low-tension regime.

  1. Hybrid Microscopy: Enabling Inexpensive High-Performance Imaging through Combined Physical and Optical Magnifications

    Science.gov (United States)

    Zhang, Yu Shrike; Chang, Jae-Byum; Alvarez, Mario Moisés; Trujillo-de Santiago, Grissel; Aleman, Julio; Batzaya, Byambaa; Krishnadoss, Vaishali; Ramanujam, Aishwarya Aravamudhan; Kazemzadeh-Narbat, Mehdi; Chen, Fei; Tillberg, Paul W.; Dokmeci, Mehmet Remzi; Boyden, Edward S.; Khademhosseini, Ali

    2016-03-01

    To date, much effort has been expended on making high-performance microscopes through better instrumentation. Recently, it was discovered that physical magnification of specimens was possible, through a technique called expansion microscopy (ExM), raising the question of whether physical magnification, coupled to inexpensive optics, could together match the performance of high-end optical equipment, at a tiny fraction of the price. Here we show that such “hybrid microscopy” methods—combining physical and optical magnifications—can indeed achieve high performance at low cost. By physically magnifying objects, then imaging them on cheap miniature fluorescence microscopes (“mini-microscopes”), it is possible to image at a resolution comparable to that previously attainable only with benchtop microscopes that present costs orders of magnitude higher. We believe that this unprecedented hybrid technology that combines expansion microscopy, based on physical magnification, and mini-microscopy, relying on conventional optics—a process we refer to as Expansion Mini-Microscopy (ExMM)—is a highly promising alternative method for performing cost-effective, high-resolution imaging of biological samples. With further advancement of the technology, we believe that ExMM will find widespread applications for high-resolution imaging particularly in research and healthcare scenarios in undeveloped countries or remote places.

  2. Siloxane based Organic-Inorganic Hybrid Polymers and their Applications for Nanostructured Optical/Photonic Components

    Directory of Open Access Journals (Sweden)

    Rahmat Hidayat

    2014-11-01

    Full Text Available We have studied the preparation of organic-inorganic hybrid polymer precursors by sol-gel technique and their utilization for nanostructured optical components for photonic applications. The gel polymer precursors were prepared from siloxane modified by polymerizable acrylate groups, which can be processed further by photopolymerization process. Molecular structure characterizations by means of the FTIR measurements indicate the conversion of C=C bonds into C-C bonds after photopolymerization. This bond conversion produces high cross-linking between the organic and inorganic moieties, resulting in thermally stable and chemically resistant thin polymer layer which provide unique advantages of this material for particular optical/photonic applications. By employing laser interference technique, gratings with periodicity between 400-1000 nm have been successfully fabricated. Application of those sub-micron periodicity of grating structure as active elements in optically pumped polymer laser system and Surface Plasmon Resonance (SPR based measurement system have been also explored. The experimental results therefore also show the potential applications of this hybrid polymer as a building material for micro/nano-photonics components.

  3. Aerosol optical and microphysical retrievals from a hybrid multiwavelength lidar dataset – DISCOVER-AQ 2011

    Directory of Open Access Journals (Sweden)

    P. Sawamura

    2014-03-01

    Full Text Available Retrievals of aerosol microphysical properties (e.g. effective radius, volume and surface-area concentrations and aerosol optical properties (e.g. complex index of refraction and single scattering albedo were obtained from a hybrid multiwavelength lidar dataset for the first time. In July of 2011, in the Baltimore-Washington DC region, synergistic profiling of optical and microphysical properties of aerosols with both airborne in-situ and ground-based remote sensing systems was performed during the first deployment of DISCOVER-AQ. The hybrid multiwavelength lidar dataset combines elastic ground-based measurements at 355 nm with airborne High Spectral Resolution Lidar (HSRL measurements at 532 nm and elastic measurements at 1064 nm that were obtained less than 5 km apart of each other. This was the first study in which optical and microphysical retrievals from lidar were obtained during the day and directly compared to AERONET and in-situ measurements for 11 cases. Good agreement was observed between lidar and AERONET retrievals. Larger discrepancies were observed between lidar retrievals and in-situ measurements obtained by the aircraft and aerosol hygroscopic effects are believed to be the main factor of such discrepancies.

  4. SDN architecture for optical packet and circuit integrated networks

    Science.gov (United States)

    Furukawa, Hideaki; Miyazawa, Takaya

    2016-02-01

    We have been developing an optical packet and circuit integrated (OPCI) network, which realizes dynamic optical path, high-density packet multiplexing, and flexible wavelength resource allocation. In the OPCI networks, a best-effort service and a QoS-guaranteed service are provided by employing optical packet switching (OPS) and optical circuit switching (OCS) respectively, and users can select these services. Different wavelength resources are assigned for OPS and OCS links, and the amount of their wavelength resources are dynamically changed in accordance with the service usage conditions. To apply OPCI networks into wide-area (core/metro) networks, we have developed an OPCI node with a distributed control mechanism. Moreover, our OPCI node works with a centralized control mechanism as well as a distributed one. It is therefore possible to realize SDN-based OPCI networks, where resource requests and a centralized configuration are carried out. In this paper, we show our SDN architecture for an OPS system that configures mapping tables between IP addresses and optical packet addresses and switching tables according to the requests from multiple users via a web interface. While OpenFlow-based centralized control protocol is coming into widespread use especially for single-administrative, small-area (LAN/data-center) networks. Here, we also show an interworking mechanism between OpenFlow-based networks (OFNs) and the OPCI network for constructing a wide-area network, and a control method of wavelength resource selection to automatically transfer diversified flows from OFNs to the OPCI network.

  5. Integral ceramic superstructure evaluation using time domain optical coherence tomography

    Science.gov (United States)

    Sinescu, Cosmin; Bradu, Adrian; Topala, Florin I.; Negrutiu, Meda Lavinia; Duma, Virgil-Florin; Podoleanu, Adrian G.

    2014-02-01

    Optical Coherence Tomography (OCT) is a non-invasive low coherence interferometry technique that includes several technologies (and the corresponding devices and components), such as illumination and detection, interferometry, scanning, adaptive optics, microscopy and endoscopy. From its large area of applications, we consider in this paper a critical aspect in dentistry - to be investigated with a Time Domain (TD) OCT system. The clinical situation of an edentulous mandible is considered; it can be solved by inserting 2 to 6 implants. On these implants a mesostructure will be manufactured and on it a superstructure is needed. This superstructure can be integral ceramic; in this case materials defects could be trapped inside the ceramic layers and those defects could lead to fractures of the entire superstructure. In this paper we demonstrate that a TD-OCT imaging system has the potential to properly evaluate the presence of the defects inside the ceramic layers and those defects can be fixed before inserting the prosthesis inside the oral cavity. Three integral ceramic superstructures were developed by using a CAD/CAM technology. After the milling, the ceramic layers were applied on the core. All the three samples were evaluated by a TD-OCT system working at 1300 nm. For two of the superstructures evaluated, no defects were found in the most stressed areas. The third superstructure presented four ceramic defects in the mentioned areas. Because of those defects the superstructure may fracture. The integral ceramic prosthesis was send back to the dental laboratory to fix the problems related to the material defects found. Thus, TD-OCT proved to be a valuable method for diagnosing the ceramic defects inside the integral ceramic superstructures in order to prevent fractures at this level.

  6. Hybrid Optical Comb Filter with Multi-Port Fiber Coupler for DWDM Optical Network

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Optical comb filters based on multi-port fused fiber couplers are proposed and numerically analyzed, 3-arm MZI composed by 1×7 fiber splitter and 3×3 fiber coupler, and 2-stage cascaded FIR type MZI interleave filter.

  7. Integrated Chemical Systems: The Simultaneous Formation of Hybrid Nanocomposites of Iron Oxide and Organo Silsesquioxanes

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, L; Clapsaddle, B; Jr., J S; Schaefer, D; Shea, K

    2004-10-15

    A sol-gel approach for the synthesis of hybrid nanocomposites of iron oxide and bridged polysilsesquioxanes has been established. The procedures allow for the simultaneous formation of iron oxide and polysilsesquioxane networks in monolithic xerogels and aerogels. These hybrid nanocomposites are synthesized from FeCl{sub 3} {center_dot} 6H{sub 2}O and functionalized silsesquioxane monomers in a one-pot reaction using epoxides as a gelation agent. The porosity and microstructure of the materials has been determined by nitrogen porosimetry, electron microscopy and ultra small angle X-ray scattering (USAXS). The hybrid nanocomposites exhibit a uniform dispersion of both components with no evidence for phase separation at length scales > 5 nm. At this limit of resolution it is not possible to distinguish between two independent interpenetrating networks integrated at molecular length scales or a random copolymer or mixtures of both.

  8. Evaluation of hybrid polymers for high-precision manufacturing of 3D optical interconnects by two-photon absorption lithography

    Science.gov (United States)

    Schleunitz, A.; Klein, J. J.; Krupp, A.; Stender, B.; Houbertz, R.; Gruetzner, G.

    2017-02-01

    The fabrication of optical interconnects has been widely investigated for the generation of optical circuit boards. Twophoton absorption (TPA) lithography (or high-precision 3D printing) as an innovative production method for direct manufacture of individual 3D photonic structures gains more and more attention when optical polymers are employed. In this regard, we have evaluated novel ORMOCER-based hybrid polymers tailored for the manufacture of optical waveguides by means of high-precision 3D printing. In order to facilitate future industrial implementation, the processability was evaluated and the optical performance of embedded waveguides was assessed. The results illustrate that hybrid polymers are not only viable consumables for industrial manufacture of polymeric micro-optics using generic processes such as UV molding. They also are potential candidates to fabricate optical waveguide systems down to the chip level where TPA-based emerging manufacturing techniques are engaged. Hence, it is shown that hybrid polymers continue to meet the increasing expectations of dynamically growing markets of micro-optics and optical interconnects due to the flexibility of the employed polymer material concept.

  9. Self-similar evolutions of parabolic, Hermite-Gaussian, and hybrid optical pulses: Universality and diversity.

    Science.gov (United States)

    Chen, Shihua; Yi, Lin; Guo, Dong-Sheng; Lu, Peixiang

    2005-07-01

    Three novel types of self-similar solutions, termed parabolic, Hermite-Gaussian, and hybrid pulses, of the generalized nonlinear Schrödinger equation with varying dispersion, nonlinearity, and gain or absorption are obtained. The properties of the self-similar evolutions in various nonlinear media are confirmed by numerical simulations. Despite the diversity of their formations, these self-similar pulses exhibit many universal features which can facilitate significantly the achievement of well-defined linearly chirped output pulses from an optical fiber, an amplifier, or an absorption medium, under certain parametric conditions. The other intrinsic characteristics of each type of self-similar pulses are also discussed.

  10. Integrated Plasma Simulation of Lower Hybrid Current Drive in Tokamaks

    Science.gov (United States)

    Bonoli, P. T.; Wright, J. C.; Harvey, R. W.; Batchelor, D. B.; Berry, L. A.; Kessel, C. E.; Jardin, S. C.

    2012-03-01

    It has been shown in Alcator C-Mod that the onset time for sawteeth can be delayed significantly (up to 0.5 s) relative to ohmically heated plasmas, through the injection of off-axis LH current drive power [1]. We are simulating these experiments using the Integrated Plasma Simulator (IPS) [2], where the driven LH current density profiles are computed using a ray tracing component (GENRAY) and Fokker Planck code (CQL3D) [3] that are run in a tightly coupled time advance. The background plasma is evolved using the TSC transport code with the Porcelli sawtooth model [4]. Predictions of the driven LH current profiles will be compared with simpler ``reduced'' models for LHCD such as the LSC code which is implemented in TSC and which is also invoked within the IPS. [4pt] [1] C. E. Kessel et al, Bull. of the Am. Phys. Soc. 53, Poster PP6.00074 (2008). [0pt] [2] D. Batchelor et al, Journal of Physics: Conf. Series 125, 012039 (2008). [0pt] [3] R. W. Harvey and M. G. McCoy, Proc. of the IAEA Tech. Comm. Meeting on Simulation and Modeling of Therm. Plasmas, Montreal, Canada (1992). [0pt] [4] S. C. Jardin et al, J. Comp. Phys. 66, 481 (1986).

  11. A 400G optical wireless integration delivery system.

    Science.gov (United States)

    Li, Xinying; Yu, Jianjun; Zhang, Junwen; Dong, Ze; Li, Fan; Chi, Nan

    2013-08-12

    We experimentally demonstrate a record 400G optical wireless integration system simultaneously delivering 2 × 112 Gb/s two-channel polarization-division-multiplexing 16-ary quadrature amplitude modulation (PDM-16QAM) signal at 37.5 GHz wireless carrier and 2 × 108 Gb/s two-channel PDM quadrature phase shift keying (PDM-QPSK) signal at 100 GHz wireless carrier, adopting two millimeter-wave (mm-wave) frequency bands, two orthogonal antenna polarizations, multiple-input multiple-output (MIMO), photonic mm-wave generation and advanced digital signal processing (DSP). In the case of no fiber transmission, the bit error ratios (BERs) for both the 112 Gb/s PDM-16QAM signal after 1.5 m wireless delivery at 37.5 GHz and the 108 Gb/s PDM-QPSK signal after 0.7 m wireless delivery at 100 GHz are below the pre-forward-error-correction (pre-FEC) threshold of 3.8 × 10(-3). To our knowledge, this is the first demonstration of a 400G optical wireless integration system in mm-wave frequency bands and also a capacity record of wireless delivery.

  12. Optical cavity integrated surface ion trap for enhanced light collection

    Science.gov (United States)

    Benito, Francisco M.

    Ion trap systems allow the faithful storage and manipulation of qubits encoded in the energy levels of the ions, and can be interfaced with photonic qubits that can be transmitted to connect remote quantum systems. Single photons transmitted from two remote sites, each entangled with one quantum memory, can be used to entangle distant quantum memories by interfering on a beam splitter. Efficient remote entanglement generation relies upon efficient light collection from single ions into a single mode fiber. This can be realized by integrating an ion trap with an optical cavity and employing the Purcell effect for enhancing the light collection. Remote entanglement can be used as a resource for a quantum repeater for provably secure long-distance communication or as a method for communicating within a distributed quantum information processor. We present the integration of a 1 mm optical cavity with a micro-fabricated surface ion trap. The plano-concave cavity is oriented normal to the chip surface where the planar mirror is attached underneath the trap chip. The cavity is locked using a 780 nm laser which is stabilized to Rubidium and shifted to match the 369 nm Doppler transition in Ytterbium. The linear ion trap allows ions to be shuttled in and out of the cavity mode. The Purcell enhancement of spontaneous emission into the cavity mode would then allow efficient collection of the emitted photons, enabling faster remote entanglement generation.

  13. Integrated optical biosensor for rapid detection of bacteria

    Science.gov (United States)

    Mathesz, Anna; Valkai, Sándor; Újvárosy, Attila; Aekbote, Badri; Sipos, Orsolya; Stercz, Balázs; Kocsis, Béla; Szabó, Dóra; Dér, András

    2016-02-01

    In medical diagnostics, rapid detection of pathogenic bacteria from body fluids is one of the basic issues. Most state-of-the-art methods require optical labeling, increasing the complexity, duration and cost of the analysis. Therefore, there is a strong need for developing selective sensory devices based on label-free techniques, in order to increase the speed, and reduce the cost of detection. In a recent paper, we have shown that an integrated optical Mach-Zehnder interferometer, a highly sensitive all-optical device made of a cheap photopolymer, can be used as a powerful lab-on-a-chip tool for specific, labelfree detection of proteins. By proper modifications of this technique, our interferometric biosensor was combined with a microfluidic system allowing the rapid and specific detection of bacteria from solutions, having the surface of the sensor functionalized by bacterium-specific antibodies. The experiments proved that the biosensor was able to detect Escherichia coli bacteria at concentrations of 106 cfu/ml within a few minutes, that makes our device an appropriate tool for fast, label-free detection of bacteria from body fluids such as urine or sputum. On the other hand, possible applications of the device may not be restricted to medical microbiology, since bacterial identification is an important task in microbial forensics, criminal investigations, bio-terrorism threats and in environmental studies, as well.

  14. Optical HMI with biomechanical energy harvesters integrated in textile supports

    Science.gov (United States)

    De Pasquale, G.; Kim, SG; De Pasquale, D.

    2015-12-01

    This paper reports the design, prototyping and experimental validation of a human-machine interface (HMI), named GoldFinger, integrated into a glove with energy harvesting from fingers motion. The device is addressed to medical applications, design tools, virtual reality field and to industrial applications where the interaction with machines is restricted by safety procedures. The HMI prototype includes four piezoelectric transducers applied to the fingers backside at PIP (proximal inter-phalangeal) joints, electric wires embedded in the fabric connecting the transducers, aluminum case for the electronics, wearable switch made with conductive fabrics to turn the communication channel on and off, and a LED. The electronic circuit used to manage the power and to control the light emitter includes a diodes bridge, leveling capacitors, storage battery and switch made by conductive fabric. The communication with the machine is managed by dedicated software, which includes the user interface, the optical tracking, and the continuous updating of the machine microcontroller. The energetic benefit of energy harvester on the battery lifetime is inversely proportional to the activation time of the optical emitter. In most applications, the optical port is active for 1 to 5% of the time, corresponding to battery lifetime increasing between about 14% and 70%.

  15. Use of Fiber Optic Interconnects for Signal Integrity

    Science.gov (United States)

    Phal, Yamuna D.; Phal, Deovrat D.

    2016-05-01

    Signal integrity (SI) is always a concern when it comes to high-speed data transmission. Even in space, there is a need for high-speed data transmission such as in the communication systems, monitoring various sub- systems and for other on-board experiments and applications.From Electromagneticperspective, using fiber-optic interconnect is highly recommended to avoid interference issues. This field has been explored for quite some time now, but mostly limited to applications that are on earth. Using these interconnects for harsh and extreme environments i.e. in space, requires reliability and ruggedness of interconnects and the system.This study suggests methods for optical fiber based communication systems for internal unit communication, communication within various instruments, as well as inter-board communication. A conclusion in terms of what areas need to be explored for enabling high-speed data transmission for space applications would be discussed in details. This study also explores and compares the existing technologies in the fiber-optic interconnects for space applications.

  16. Integrated planar optical waveguide interferometer biosensors: a comparative review.

    Science.gov (United States)

    Kozma, Peter; Kehl, Florian; Ehrentreich-Förster, Eva; Stamm, Christoph; Bier, Frank F

    2014-08-15

    Integrated planar optical waveguide interferometer biosensors are advantageous combinations of evanescent field sensing and optical phase difference measurement methods. By probing the near surface region of a sensor area with the evanescent field, any change of the refractive index of the probed volume induces a phase shift of the guided mode compared to a reference field typically of a mode propagating through the reference arm of the same waveguide structure. The interfering fields of these modes produce an interference signal detected at the sensor׳s output, whose alteration is proportional to the refractive index change. This signal can be recorded, processed and related to e.g. the concentration of an analyte in the solution of interest. Although this sensing principle is relatively simple, studies about integrated planar optical waveguide interferometer biosensors can mostly be found in the literature covering the past twenty years. During these two decades, several members of this sensor family have been introduced, which have remarkably advantageous properties. These entail label-free and non-destructive detection, outstandingly good sensitivity and detection limit, cost-effective and simple production, ability of multiplexing and miniaturization. Furthermore, these properties lead to low reagent consumption, short analysis time and open prospects for point-of-care applications. The present review collects the most relevant developments of the past twenty years categorizing them into two main groups, such as common- and double path waveguide interferometers. In addition, it tries to maintain the historical order as it is possible and it compares the diverse sensor designs in order to reveal not only the development of this field in time, but to contrast the advantages and disadvantages of the different approaches and sensor families, as well.

  17. Integrated modeling of the GMT laser tomography adaptive optics system

    Science.gov (United States)

    Piatrou, Piotr

    2014-08-01

    Laser Tomography Adaptive Optics (LTAO) is one of adaptive optics systems planned for the Giant Magellan Telescope (GMT). End-to-end simulation tools that are able to cope with the complexity and computational burden of the AO systems to be installed on the extremely large telescopes such as GMT prove to be an integral part of the GMT LTAO system development endeavors. SL95, the Fortran 95 Simulation Library, is one of the software tools successfully used for the LTAO system end-to-end simulations. The goal of SL95 project is to provide a complete set of generic, richly parameterized mathematical models for key elements of the segmented telescope wavefront control systems including both active and adaptive optics as well as the models for atmospheric turbulence, extended light sources like Laser Guide Stars (LGS), light propagation engines and closed-loop controllers. The library is implemented as a hierarchical collection of classes capable of mutual interaction, which allows one to assemble complex wavefront control system configurations with multiple interacting control channels. In this paper we demonstrate the SL95 capabilities by building an integrated end-to-end model of the GMT LTAO system with 7 control channels: LGS tomography with Adaptive Secondary and on-instrument deformable mirrors, tip-tilt and vibration control, LGS stabilization, LGS focus control, truth sensor-based dynamic noncommon path aberration rejection, pupil position control, SLODAR-like embedded turbulence profiler. The rich parameterization of the SL95 classes allows to build detailed error budgets propagating through the system multiple errors and perturbations such as turbulence-, telescope-, telescope misalignment-, segment phasing error-, non-common path-induced aberrations, sensor noises, deformable mirror-to-sensor mis-registration, vibration, temporal errors, etc. We will present a short description of the SL95 architecture, as well as the sample GMT LTAO system simulation

  18. A multiply-add engine with monolithically integrated 3D memristor crossbar/CMOS hybrid circuit

    Science.gov (United States)

    Chakrabarti, B.; Lastras-Montaño, M. A.; Adam, G.; Prezioso, M.; Hoskins, B.; Cheng, K.-T.; Strukov, D. B.

    2017-02-01

    Silicon (Si) based complementary metal-oxide semiconductor (CMOS) technology has been the driving force of the information-technology revolution. However, scaling of CMOS technology as per Moore’s law has reached a serious bottleneck. Among the emerging technologies memristive devices can be promising for both memory as well as computing applications. Hybrid CMOS/memristor circuits with CMOL (CMOS + “Molecular”) architecture have been proposed to combine the extremely high density of the memristive devices with the robustness of CMOS technology, leading to terabit-scale memory and extremely efficient computing paradigm. In this work, we demonstrate a hybrid 3D CMOL circuit with 2 layers of memristive crossbars monolithically integrated on a pre-fabricated CMOS substrate. The integrated crossbars can be fully operated through the underlying CMOS circuitry. The memristive devices in both layers exhibit analog switching behavior with controlled tunability and stable multi-level operation. We perform dot-product operations with the 2D and 3D memristive crossbars to demonstrate the applicability of such 3D CMOL hybrid circuits as a multiply-add engine. To the best of our knowledge this is the first demonstration of a functional 3D CMOL hybrid circuit.

  19. A multiply-add engine with monolithically integrated 3D memristor crossbar/CMOS hybrid circuit

    Science.gov (United States)

    Chakrabarti, B.; Lastras-Montaño, M. A.; Adam, G.; Prezioso, M.; Hoskins, B.; Cheng, K.-T.; Strukov, D. B.

    2017-01-01

    Silicon (Si) based complementary metal-oxide semiconductor (CMOS) technology has been the driving force of the information-technology revolution. However, scaling of CMOS technology as per Moore’s law has reached a serious bottleneck. Among the emerging technologies memristive devices can be promising for both memory as well as computing applications. Hybrid CMOS/memristor circuits with CMOL (CMOS + “Molecular”) architecture have been proposed to combine the extremely high density of the memristive devices with the robustness of CMOS technology, leading to terabit-scale memory and extremely efficient computing paradigm. In this work, we demonstrate a hybrid 3D CMOL circuit with 2 layers of memristive crossbars monolithically integrated on a pre-fabricated CMOS substrate. The integrated crossbars can be fully operated through the underlying CMOS circuitry. The memristive devices in both layers exhibit analog switching behavior with controlled tunability and stable multi-level operation. We perform dot-product operations with the 2D and 3D memristive crossbars to demonstrate the applicability of such 3D CMOL hybrid circuits as a multiply-add engine. To the best of our knowledge this is the first demonstration of a functional 3D CMOL hybrid circuit. PMID:28195239

  20. Electric-Magneto-Optical Kerr Effect in a Hybrid Organic-Inorganic Perovskite.

    Science.gov (United States)

    Fan, Feng-Ren; Wu, Hua; Nabok, Dmitrii; Hu, Shunbo; Ren, Wei; Draxl, Claudia; Stroppa, Alessandro

    2017-09-20

    Hybrid organic-inorganic compounds attract a lot of interest for their flexible structures and multifunctional properties. For example, they can have coexisting magnetism and ferroelectricity whose possible coupling gives rise to magnetoelectricity. Here using first-principles computations, we show that, in a perovskite metal-organic framework (MOF), the magnetic and electric orders are further coupled to optical excitations, leading to an Electric tuning of the Magneto-Optical Kerr effect (EMOKE). Moreover, the Kerr angle can be switched by reversal of both ferroelectric and magnetic polarization only. The interplay between the Kerr angle and the organic-inorganic components of MOFs offers surprising unprecedented tools for engineering MOKE in complex compounds. Note that this work may be relevant to acentric magnetic systems in general, e.g., multiferroics.

  1. HOWRAN: An Hybrid Optical Wireless Radio Access Network for WiMAX Antennas Backhauling

    Science.gov (United States)

    Gagnaire, Maurice; Youssef, Tony

    In comparison to existing 3G or 3G+ wireless systems, fourth generation (4G), long-term evolution (LTE) or mobile Wimax are characterized by higher bit rates, highly fluctuant traffic matrices and higher antenna’s density. Current backhauling techniques federating radio antennas are not suited to these new characteristics. Several investigations are carried out for the design of new generation radio access networks (NG-RAN) in charge of concentrating radio cellular traffic from the base stations to the core network. In this paper, we propose an original approach based on an Hybrid Optical Wireless Radio Access Network (HOWRAN) exploiting the benefits of radio-over-fiber technologies and of recent advances in the field of optical devices and systems. As an illustration, we apply the HOWRAN concept to the backhauling of fixed or mobile WiMAX base stations. The two main innovative aspects of HOWRAN are depicted: its hardware architecture and its control plane.

  2. The Detection of Defects in Optical Fibers Using a Hybrid Opto-electronic Correlator

    Institute of Scientific and Technical Information of China (English)

    LIU Yange; LIU Wei; ZHANG Yimo; ZHOU Ge

    2000-01-01

    A hybrid opto-electronic correlator for detecting defects in optical fibers is proposed. After the light from a He-Ne laser being expanded and filtered it is not collimated but directly passes a Fourier transform lens and illuminates a reference fiber and a test fiber at the same input plane. The Fourier transform spectrum of the two fibers is therefore obtained at the rear focal plane of the lens, where it is sampled via a CCD array connected with a computer through a frame grabber. The computer performs filter, inverse Fourier transform and setting threshold operation on classification. The system is an equivalent of joint transform correlator with a Fourier lens of long focal length. The experiment results for optical fibers having incoordinate defects are presented. The results indicate that the system can be used for fiber defect detection, and has the advantages of high identification, compact configuration, easy adjustment and flexible manipulation.

  3. Overview of ERA Integrated Technology Demonstration (ITD) 51A Ultra-High Bypass (UHB) Integration for Hybrid Wing Body (HWB)

    Science.gov (United States)

    Flamm, Jeffrey D.; James, Kevin D.; Bonet, John T.

    2016-01-01

    The NASA Environmentally Responsible Aircraft Project (ERA) was a ve year project broken into two phases. In phase II, high N+2 Technical Readiness Level demonstrations were grouped into Integrated Technology Demonstrations (ITD). This paper describes the work done on ITD-51A: the Vehicle Systems Integration, Engine Airframe Integration Demonstration. Refinement of a Hybrid Wing Body (HWB) aircraft from the possible candidates developed in ERA Phase I was continued. Scaled powered, and unpowered wind- tunnel testing, with and without acoustics, in the NASA LARC 14- by 22-foot Subsonic Tunnel, the NASA ARC Unitary Plan Wind Tunnel, and the 40- by 80-foot test section of the National Full-Scale Aerodynamics Complex (NFAC) in conjunction with very closely coupled Computational Fluid Dynamics was used to demonstrate the fuel burn and acoustic milestone targets of the ERA Project.

  4. Full Wave Simulation of Integrated Circuits Using Hybrid Numerical Methods

    Science.gov (United States)

    Tan, Jilin

    Transmission lines play an important role in digital electronics, and in microwave and millimeter-wave circuits. Analysis, modeling, and design of transmission lines are critical to the development of the circuitry in the chip, subsystem, and system levels. In the past several decays, at the EM modeling level, the quasi-static approximation has been widely used due to its great simplicity. As the clock rates increase, the inter-connect effects such as signal delay, distortion, dispersion, reflection, and crosstalk, limit the performance of microwave systems. Meanwhile, the quasi-static approach loses its validity for some complex system structures. Since the successful system design of the PCB, MCM, and the chip packaging, rely very much on the computer aided EM level modeling and simulation, many new methods have been developed, such as the full wave approach, to guarantee the successful design. Many difficulties exist in the rigorous EM level analysis. Some of these include the difficulties in describing the behavior of the conductors with finite thickness and finite conductivity, the field singularity, and the arbitrary multilayered multi-transmission lines structures. This dissertation concentrates on the full wave study of the multi-conductor transmission lines with finite conductivity and finite thickness buried in an arbitrary lossy multilayered environment. Two general approaches have been developed. The first one is the integral equation method in which the dyadic Green's function for arbitrary layered media has been correctly formulated and has been tested both analytically and numerically. By applying this method, the double layered high dielectric permitivitty problem and the heavy dielectrical lossy problem in multilayered media in the CMOS circuit design have been solved. The second approach is the edge element method. In this study, the correct functional for the two dimensional propagation problem has been successfully constructed in a rigorous way

  5. Drive to miniaturization: integrated optical networks on mobile platforms

    Science.gov (United States)

    Salour, Michael M.; Batayneh, Marwan; Figueroa, Luis

    2011-11-01

    With rapid growth of the Internet, bandwidth demand for data traffic is continuing to explode. In addition, emerging and future applications are becoming more and more network centric. With the proliferation of data communication platforms and data-intensive applications (e.g. cloud computing), high-bandwidth materials such as video clips dominating the Internet, and social networking tools, a networking technology is very desirable which can scale the Internet's capability (particularly its bandwidth) by two to three orders of magnitude. As the limits of Moore's law are approached, optical mesh networks based on wavelength-division multiplexing (WDM) have the ability to satisfy the large- and scalable-bandwidth requirements of our future backbone telecommunication networks. In addition, this trend is also affecting other special-purpose systems in applications such as mobile platforms, automobiles, aircraft, ships, tanks, and micro unmanned air vehicles (UAVs) which are becoming independent systems roaming the sky while sensing data, processing, making decisions, and even communicating and networking with other heterogeneous systems. Recently, WDM optical technologies have seen advances in its transmission speeds, switching technologies, routing protocols, and control systems. Such advances have made WDM optical technology an appealing choice for the design of future Internet architectures. Along these lines, scientists across the entire spectrum of the network architectures from physical layer to applications have been working on developing devices and communication protocols which can take full advantage of the rapid advances in WDM technology. Nevertheless, the focus has always been on large-scale telecommunication networks that span hundreds and even thousands of miles. Given these advances, we investigate the vision and applicability of integrating the traditionally large-scale WDM optical networks into miniaturized mobile platforms such as UAVs. We explain

  6. Series-connected substrate-integrated lead-carbon hybrid ultracapacitors with voltage-management circuit

    Indian Academy of Sciences (India)

    A Banerjee; R Srinivasan; A K Shukla

    2015-02-01

    Cell voltage for a fully charged-substrate-integrated lead-carbon hybrid ultracapacitor is about 2.3 V. Therefore, for applications requiring higher DC voltage, several of these ultracapacitors need to be connected in series. However, voltage distribution across each series-connected ultracapacitor tends to be uneven due to tolerance in capacitance and parasitic parallel-resistance values. Accordingly, voltage-management circuit is required to protect constituent ultracapacitors from exceeding their rated voltage. In this study, the design and characterization of the substrate-integrated lead-carbon hybrid ultracapacitor with co-located terminals is discussed. Voltage-management circuit for the ultracapacitor is presented, and its effectiveness is validated experimentally.

  7. Detection of Phaeocystis globosa using sandwich hybridization integrated with nuclease protection assay (NPA-SH)

    Institute of Scientific and Technical Information of China (English)

    ZHEN Yu; MI Tiezhu; YU Zhigang

    2008-01-01

    Phaeocystis globosa Scherffel is one of the common harmful algae species in coastal waters of the southeastern China. In this study, sandwich hybridization integrated with nuclease protection assay (NPA-SH) was used to qualitatively and quantitatively detect P. globosa. Results showed that this method had good applicability and validity in analyzing the samples from laboratory cultures and from fields. The linear regression equation for P. globosa was obtained, and the lowest detection number of cells was 1.8×104 cells. Statistics showed that there was no distinct difference between the results of detecting the microalgae by NPA-SH and traditional microscopy. This technique has good reliability, accuracy, and can give a remarkably high sample processing rate. Sandwich hybridization integrated with nuclease protection assay will provide an efficient alternative to microscopic method for monitoring and investigating the bloom of P. globosa.

  8. Optical properties of polysiloxane hybrid thin films containing nano-sized Ag-As-Se chalcogenide clusters

    Science.gov (United States)

    Zha, Congji; Osvath, Peter; Wilson, Gerry; Launikonis, Anton

    2009-02-01

    Chalcogenide glasses are attractive for all-optical signal processing due to their outstanding optical properties, including large optical nonlinearity, a high refractive index and high photosensitivity. In device fabrication, a challenge lies in the difficulty of obtaining thin films with a high stability and good uniformity. In this paper, optical thin films containing nano-sized chalcogenide clusters in polysiloxane matrices are fabricated by a modified plasma deposition process. The optical absorption and luminescence emission properties of the hybrid thin films were characterized by UV-Vis-NIR and fluorescence spectroscopy. Luminescent emission from Ag-As-Se nano-sized clusters was observed for the first time in these nano-hybrid thin films, and the mechanism was discussed.

  9. A full-duplex optical access system with hybrid 64/16/4QAM-OFDM downlink

    Science.gov (United States)

    He, Chao; Tan, Ze-fu; Shao, Yu-feng; Cai, Li; Pu, He-sheng; Zhu, Yun-le; Huang, Si-si; Liu, Yu

    2016-09-01

    A full-duplex optical passive access scheme is proposed and verified by simulation, in which hybrid 64/16/4-quadrature amplitude modulation (64/16/4QAM) orthogonal frequency division multiplexing (OFDM) optical signal is for downstream transmission and non-return-to-zero (NRZ) optical signal is for upstream transmission. In view of the transmitting and receiving process for downlink optical signal, in-phase/quadrature-phase (I/Q) modulation based on Mach-Zehnder modulator (MZM) and homodyne coherent detection technology are employed, respectively. The simulation results show that the bit error ratio ( BER) less than hardware decision forward error correction (HD-FEC) threshold is successfully obtained over transmission path with 20-km-long standard single mode fiber (SSMF) for hybrid downlink modulation OFDM optical signal. In addition, by dividing the system bandwidth into several subchannels consisting of some continuous subcarriers, it is convenient for users to select different channels depending on requirements of communication.

  10. Femtosecond laser fabrication for the integration of optical sensors in microfluidic lab-on-chip devices

    NARCIS (Netherlands)

    Osellame, R.; Martinez-Vazquez, R.; Dongre, C.; Dekker, R.; Hoekstra, H.J.W.M.; Ramponi, R.; Pollnau, M.; Cerullo, G.; Corkum, P.; Silvestri, de S.; Nelson, K.A.; Riedle, E.; Schoenlein, R.W.

    2009-01-01

    Femtosecond lasers enable the fabrication of both optical waveguides and buried microfluidic channels on a glass substrate. The waveguides are used to integrate optical detection in a commercial microfluidic lab-on-chip for capillary electrophoresis.

  11. Femtosecond laser fabrication for the integration of optical sensors in microfluidic lab-on-chip devices

    NARCIS (Netherlands)

    Osellame, R.; Martinez Vazquez, R.; Dongre, C.; Dekker, R.; Hoekstra, H.J.W.M.; Pollnau, M.; Ramponi, R.; Cerullo, G.

    2008-01-01

    Femtosecond lasers enable the fabrication of both optical waveguides and buried microfluidic channels on a glass substrate. The waveguides are used to integrate optical detection in a commercial microfluidic lab-on-chip for capillary electrophoresis

  12. Feasibility study of a hybrid wind turbine system – integration with compressed air energy storage

    OpenAIRE

    Sun, Hao; Luo, Xing; Wang, Jihong

    2015-01-01

    Wind has been recognized as one of major realistic clean energy sources for power generation to meet the continuously increased energy demand and to achieve the carbon emission reduction targets. However, the utilisation of wind energy encounters an inevitable challenge resulting from the nature of wind intermittency. To address this, the paper presents the recent research work at Warwick on the feasibility study of a new hybrid system by integrating a wind turbine with compressed air energy ...

  13. Hybrid Lifting Wavelet-Like Transform for Solution of Electromagnetic Integral Equation

    Institute of Scientific and Technical Information of China (English)

    CHEN Ming-Sheng; WU Xian-Liang; SHA Wei; HUANG Zhi-Xiang

    2008-01-01

    @@ A hybrid lifting wavelet-like transform scheme is successfully applied to the solution of electric field integral equation using Rao-Wilton-Glisson basis functions.To speed up the matrix transform process,the lifting scheme is adopted.Numerical examples of different three-dimensional perfectly electric conducting objects are considered.Compared with the method of moments,the proposed matrix transform scheme can save considerable CPU time and memory.

  14. The topological structure of the integral quantum Hall effect in magnetic semiconductor-superconductor hybrids

    Institute of Scientific and Technical Information of China (English)

    Ren Ji-Rong; Zhu Hui

    2009-01-01

    An unconventional integer quantum Hall regime was found in magnetic semiconductor-superconductor hybrids.By making use of the decomposition of the gauge potential on a U(1) principal fibre bundle over k-space, we study the topological structure of the integral Hall conductance. It is labeled by the Hopf index β and the Brouwer degree η. The Hall conductance topological current and its evolution is discussed.

  15. Physical Properties and Behaviour of Highly Bi-Substituted Magneto-Optic Garnets for Applications in Integrated Optics and Photonics

    Directory of Open Access Journals (Sweden)

    Mohammad Nur-E-Alam

    2011-01-01

    Full Text Available Rare-earth and Bi-substituted iron garnet thin film materials exhibit strong potential for application in various fields of science and frontier optical technologies. Bi-substituted iron garnets possess extraordinary optical and MO properties and are still considered as the best MO functional materials for various emerging integrated optics and photonics applications. However, these MO garnet materials are rarely seen in practical photonics use due to their high optical losses in the visible spectral region. In this paper, we report on the physical properties and magneto-optic behaviour of high-performance RF sputtered highly bismuth-substituted iron garnet and garnet-oxide nanocomposite films of generic composition type (Bi, Dy/Lu3(Fe, Ga/Al5O12. Our newly synthesized garnet materials form high-quality nanocrystalline thin film layers which demonstrate excellent optical and MO properties suitable for a wide range of applications in integrated optics and photonics.

  16. Lithium-niobate-based integrated optic chip utilizing digital electrode layout for use in a miniature fiber optic rate sensor

    Science.gov (United States)

    Ner, Manjeet S.; Groellmann, Peter; Mutter, Gerhard

    1995-09-01

    This paper describes to the best of our knowledge the first implementation of a lithium niobate based 8 bit electroded integrated optic waveguide fiber optic gyro chip referred here as 'Digi- MIOC' (digital-electroded multifunction integrated optic chip, which has been used in a Sagnac effect exploiting microfiber optic rate sensor ((mu) -FORS) developed by LITEF. The paper highlights various features of a Digi-MIOC, such as design philosophy, fabrication aspects, and test procedures to evaluate static and dynamic characteristics of the electro-optic parameters. When used in closed loop operation, the Digi-MIOC forms the key optical component of a (mu) -FORS to aid the required optical-to-electrical signal processing to give linear output for input rates of rotation. Various test results and features of LITEF's (mu) - FORS, such as small size, large rotation rate measurement potential, low drive power, and high reliabliity are also highlighted.

  17. Solar Field Optical Characterization at Stillwater Geothermal/Solar Hybrid Plant

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Guangdong [National Renewable Energy Laboratory,15013 Denver West Parkway,Golden, CO 80401e-mail: Guangdong.Zhu@nrel.gov; Turchi, Craig [National Renewable Energy Laboratory,15013 Denver West Parkway,Golden, CO 80401

    2017-01-27

    Concentrating solar power (CSP) can provide additional thermal energy to boost geothermal plant power generation. For a newly constructed solar field at a geothermal power plant site, it is critical to properly characterize its performance so that the prediction of thermal power generation can be derived to develop an optimum operating strategy for a hybrid system. In the past, laboratory characterization of a solar collector has often extended into the solar field performance model and has been used to predict the actual solar field performance, disregarding realistic impacting factors. In this work, an extensive measurement on mirror slope error and receiver position error has been performed in the field by using the optical characterization tool called Distant Observer (DO). Combining a solar reflectance sampling procedure, a newly developed solar characterization program called FirstOPTIC and public software for annual performance modeling called System Advisor Model (SAM), a comprehensive solar field optical characterization has been conducted, thus allowing for an informed prediction of solar field annual performance. The paper illustrates this detailed solar field optical characterization procedure and demonstrates how the results help to quantify an appropriate tracking-correction strategy to improve solar field performance. In particular, it is found that an appropriate tracking-offset algorithm can improve the solar field performance by about 15%. The work here provides a valuable reference for the growing CSP industry.

  18. Chip-integrated ultrawide-band all-optical logic comparator in plasmonic circuits

    OpenAIRE

    Lu, Cuicui; Hu, Xiaoyong; Yang, Hong; Gong, Qihuang

    2014-01-01

    Optical computing opens up the possibility for the realization of ultrahigh-speed and ultrawide-band information processing. Integrated all-optical logic comparator is one of the indispensable core components of optical computing systems. Unfortunately, up to now, no any nanoscale all-optical logic comparator suitable for on-chip integration applications has been realized experimentally. Here, we report a subtle and effective technical solution to circumvent the obstacles of inherent Ohmic lo...

  19. Nuclear Hybrid Energy Systems Initial Integrated Case Study Development and Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, Thomas J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Greenwood, Michael Scott [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-12-01

    The US Department of Energy Office of Nuclear Energy established the Nuclear Hybrid Energy System (NHES) project to develop a systematic, rigorous, technically accurate set of methods to model, analyze, and optimize the integration of dispatchable nuclear, fossil, and electric storage with an industrial customer. Ideally, the optimized integration of these systems will provide economic and operational benefits to the overall system compared to independent operation, and it will enhance the stability and responsiveness of the grid as intermittent, nondispatchable, renewable resources provide a greater share of grid power.

  20. Hybrid Bernstein Block-Pulse Functions Method for Second Kind Integral Equations with Convergence Analysis

    Directory of Open Access Journals (Sweden)

    Mohsen Alipour

    2014-01-01

    Full Text Available We introduce a new combination of Bernstein polynomials (BPs and Block-Pulse functions (BPFs on the interval [0, 1]. These functions are suitable for finding an approximate solution of the second kind integral equation. We call this method Hybrid Bernstein Block-Pulse Functions Method (HBBPFM. This method is very simple such that an integral equation is reduced to a system of linear equations. On the other hand, convergence analysis for this method is discussed. The method is computationally very simple and attractive so that numerical examples illustrate the efficiency and accuracy of this method.