WorldWideScience

Sample records for hull vibratory springing

  1. On the wave induced responses for a high-speed hydrofoil catamaran. Part 2. Cabin connected to hull by spring and response to vibration; Suichuyokutsuki kosoku sodotei no harochu oto ni tsuite. 2. Dokuritsu kozogata cabin to yodo oto

    Energy Technology Data Exchange (ETDEWEB)

    Nobukawa, H; Kitamura, M; Kawamura, T [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1996-04-10

    A high-speed hydrofoil catamaran under development has such a structure that an independent cabin is mounted on catamaran hulls, the cabin is connected with the hulls by using four soft springs, and hydrofoils are attached to the front and rear of the cabin. The structural design conception was as follows: the self-weight of the cabin is supported by lifting power of the hydrofoils while the boat is cruising; longitudinal motions of the catamaran hulls are absorbed by soft spring struts to make the motions more difficult to be transmitted into the cabin; and vibration excited by engines rotating at high speeds, attached to rear of the catamaran hulls, is not transmitted directly to the cabin structurally. A towing experiment was carried out by using divided models of about 1/10 scale in counter waves and regular waves to investigate their vibration response characteristics in waves. Furthermore, an experimental boat made of aluminum alloy with about 1/3 scale of the design boat was attached with composite structural struts made of springs and rubber parts to perform cruising experiments on an actual sea area. As a result, it was found that vibration excited by main engines in the catamaran hulls is transmitted very little to the cabin. 2 refs., 10 figs., 1 tab.

  2. Settlement during vibratory sheet piling

    NARCIS (Netherlands)

    Meijers, P.

    2007-01-01

    During vibratory sheet piling quite often the soil near the sheet pile wall will settle. In many cases this is not a problem. For situations with houses, pipelines, roads or railroads at relative short distance these settlements may not be acceptable. The purpose of the research described in this

  3. Alpha-Concave Hull, a Generalization of Convex Hull

    OpenAIRE

    Asaeedi, Saeed; Didehvar, Farzad; Mohades, Ali

    2013-01-01

    Bounding hull, such as convex hull, concave hull, alpha shapes etc. has vast applications in different areas especially in computational geometry. Alpha shape and concave hull are generalizations of convex hull. Unlike the convex hull, they construct non-convex enclosure on a set of points. In this paper, we introduce another generalization of convex hull, named alpha-concave hull, and compare this concept with convex hull and alpha shape. We show that the alpha-concave hull is also a general...

  4. GEC Ferranti piezo vibratory gyroscope

    Science.gov (United States)

    Nuttall, J. D.

    1993-01-01

    Prototypes of a piezo-electric vibratory angular rate transducer (gyroscope) (PVG) have been constructed and evaluated. The construction is on the lines suggested by Burdess. The sensitive element is a cylinder of radially poled piezo-electric ceramic. The cylinder is metallized inside and out, and the outer metallization is divided into eight electrodes. The metallization on the inside is earthed. A phase locked loop, using pairs of the electrodes, causes the cylinder to vibrate in one of its two fundamental, degenerate modes. In the presence of rotation, some of the vibration is coupled into the outer mode. This can be detected, or suppressed with a closed-up technique and provides a measure of rotation rate. The gyroscope provides a number of advantages over rotating mass and optical instruments: low size and mass, lower power consumption, potentially high reliability, potentially good dormancy, low cost and high maximum rate.

  5. Repairing the vibratory vocal fold.

    Science.gov (United States)

    Long, Jennifer L

    2018-01-01

    A vibratory vocal fold replacement would introduce a new treatment paradigm for structural vocal fold diseases such as scarring and lamina propria loss. This work implants a tissue-engineered replacement for vocal fold lamina propria and epithelium in rabbits and compares histology and function to injured controls and orthotopic transplants. Hypotheses were that the cell-based implant would engraft and control the wound response, reducing fibrosis and restoring vibration. Translational research. Rabbit adipose-derived mesenchymal stem cells (ASC) were embedded within a three-dimensional fibrin gel, forming the cell-based outer vocal fold replacement (COVR). Sixteen rabbits underwent unilateral resection of vocal fold epithelium and lamina propria, as well as reconstruction with one of three treatments: fibrin glue alone with healing by secondary intention, replantation of autologous resected vocal fold cover, or COVR implantation. After 4 weeks, larynges were examined histologically and with phonation. Fifteen rabbits survived. All tissues incorporated well after implantation. After 1 month, both graft types improved histology and vibration relative to injured controls. Extracellular matrix (ECM) of the replanted mucosa was disrupted, and ECM of the COVR implants remained immature. Immune reaction was evident when male cells were implanted into female rabbits. Best histologic and short-term vibratory outcomes were achieved with COVR implants containing male cells implanted into male rabbits. Vocal fold cover replacement with a stem cell-based tissue-engineered construct is feasible and beneficial in acute rabbit implantation. Wound-modifying behavior of the COVR implant is judged to be an important factor in preventing fibrosis. NA. Laryngoscope, 128:153-159, 2018. © 2017 The American Laryngological, Rhinological and Otological Society, Inc.

  6. Vocal Fold Vibratory Changes Following Surgical Intervention.

    Science.gov (United States)

    Chen, Wenli; Woo, Peak; Murry, Thomas

    2016-03-01

    High-speed videoendoscopy (HSV) captures direct cycle-to-cycle visualization of vocal fold movement in real time. This ultrafast recording rate is capable of visualizing the vibratory motion of the vocal folds in severely disordered phonation and provides a direct method for examining vibratory changes after vocal fold surgery. The purpose of this study was to examine the vibratory motion before and after surgical intervention. HSV was captured from two subjects with identifiable midvocal fold benign lesions and six subjects with highly aperiodic vocal fold vibration before and after phonosurgery. Digital kymography (DKG) was used to extract high-speed kymographic vocal fold images sampled at the midmembranous, anterior 1/3, and posterior 1/3 region. Spectral analysis was subsequently applied to the DKG to quantify the cycle-to-cycle movements of the left and the right vocal fold, expressed as a spectrum. Before intervention, the vibratory spectrum consisted of decreased and flat-like spectral peaks with robust power asymmetry. After intervention, increases in spectral power and decreases in power symmetry were noted. Spectral power increases were most remarkable in the midmembranous region of the vocal fold. Surgical modification resulted in improved lateral excursion of the vocal folds, vibratory function, and perceptual measures of Voice Handicap Index-10. These changes in vibratory behavior trended toward normal vocal fold vibration. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

  7. Measurement of leached hulls

    International Nuclear Information System (INIS)

    Reilly, T.D.

    1979-07-01

    Leached hulls are the short lengths of fuel rod cladding and fuel element hardware which constitute a major waste product of a reprocessing plant employing a chop-and-leach head-end process. The small, undissolved fuel residue (0.1 to 1.0% of original fuel content) which is discarded with this waste must be measured for safeguards, material accountability, and process control reasons. This report gives a critical analysis of hull measurement techniques involving the analysis of fission product gamma rays, spontaneous fission neutrons from curium, and delayed neutron activation. Major emphasis is given to the measurement of 2186-keV gamma rays from 144 Ce-- 144 Pr. A detailed description of typical leached hull characteristics is presented at the beginning of the report. An extensive review of experience gained from existing hull measurement systems in the United Kingdom, France, Japan, Germany, Italy, and the United States is presented

  8. Dynamic Planar Convex Hull

    DEFF Research Database (Denmark)

    Jacob, Riko

    We determine the computational complexity of the dynamic convex hull problem in the planar case. We present a data structure that maintains a finite set of n points in the plane under insertion and deletion of points in amortized O(log n) time per operation. The space usage of the data structure...... is O(n). The data structure supports extreme point queries in a given direction, tangent queries through a given point, and queries for the neighboring points on the convex hull in O(log n) time. The extreme point queries can be used to decide whether or not a given line intersects the convex hull......, and the tangent queries to determine whether a given point is inside the convex hull. The space usage of the data structure is O(n). We give a lower bound on the amortized asymptotic time complexity that matches the performance of this data structure....

  9. Dynamic Planar Convex Hull

    DEFF Research Database (Denmark)

    Brodal, Gerth Stølfting; Jacob, Rico

    2002-01-01

    In this paper we determine the computational complexity of the dynamic convex hull problem in the planar case. We present a data structure that maintains a finite set of n points in the plane under insertion and deletion of points in amortized O(log n) time per operation. The space usage of the d......In this paper we determine the computational complexity of the dynamic convex hull problem in the planar case. We present a data structure that maintains a finite set of n points in the plane under insertion and deletion of points in amortized O(log n) time per operation. The space usage...... of the data structure is O(n). The data structure supports extreme point queries in a given direction, tangent queries through a given point, and queries for the neighboring points on the convex hull in O(log n) time. The extreme point queries can be used to decide whether or not a given line intersects...... the convex hull, and the tangent queries to determine whether a given point is inside the convex hull. We give a lower bound on the amortized asymptotic time complexity that matches the performance of this data structure....

  10. 14 CFR 23.755 - Hulls.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hulls. 23.755 Section 23.755 Aeronautics... Hulls § 23.755 Hulls. (a) The hull of a hull seaplane or amphibian of 1,500 pounds or more maximum weight must have watertight compartments designed and arranged so that the hull auxiliary floats, and...

  11. Effective Hull IMMR plan

    Energy Technology Data Exchange (ETDEWEB)

    Franco, Mireille

    2010-07-01

    The objective of the Hull Inspection, Maintenance and Repair Plan is to ensure the total integrity of the Floating Production Unit. To be efficient, the Monitoring has to be part of the Hull Inspection, Monitoring, Maintenance and Repair Plan (IMMR). The IMMR Plan should be developed during the design and project phases and take into account the interfaces between the different systems and teams' tasks in operation. The IMMR is multidisciplinary and form part of the hand-over to ensure an efficient and early implementation. Implementation of such a complex plan requires: - Cross-functionality: take advantage of the synergies - Boldness: break the mould and think outside the box - Listening: be attentive, be available, - Mutual support: during good and bad times. This paper presents the way Total believe the Hull IMMR Plan shall be developed, implemented and followed up. (Author)

  12. Multi-purpose hull

    International Nuclear Information System (INIS)

    Taylor, W.C.; Horgan, J.B.G.; Downie, D.M.

    1982-01-01

    An 18 sided hull approximately 4 metres in diameter formed in prefabricated watertight sections from GRP has been designed for burying underground to withstand an overpressure of 12P.S.I above normal atmospheric pressure for human protection against a nuclear explosion and resultant radioactivity. The pre-fabricated sections are so designed to be stacked together prior to assembling and the assembled hulls can also be stacked together both vertically and horizontally in a honeycomb formation to form a multiple chamber. (author)

  13. Modal Damping Ratio and Optimal Elastic Moduli of Human Body Segments for Anthropometric Vibratory Model of Standing Subjects.

    Science.gov (United States)

    Gupta, Manoj; Gupta, T C

    2017-10-01

    The present study aims to accurately estimate inertial, physical, and dynamic parameters of human body vibratory model consistent with physical structure of the human body that also replicates its dynamic response. A 13 degree-of-freedom (DOF) lumped parameter model for standing person subjected to support excitation is established. Model parameters are determined from anthropometric measurements, uniform mass density, elastic modulus of individual body segments, and modal damping ratios. Elastic moduli of ellipsoidal body segments are initially estimated by comparing stiffness of spring elements, calculated from a detailed scheme, and values available in literature for same. These values are further optimized by minimizing difference between theoretically calculated platform-to-head transmissibility ratio (TR) and experimental measurements. Modal damping ratios are estimated from experimental transmissibility response using two dominant peaks in the frequency range of 0-25 Hz. From comparison between dynamic response determined form modal analysis and experimental results, a set of elastic moduli for different segments of human body and a novel scheme to determine modal damping ratios from TR plots, are established. Acceptable match between transmissibility values calculated from the vibratory model and experimental measurements for 50th percentile U.S. male, except at very low frequencies, establishes the human body model developed. Also, reasonable agreement obtained between theoretical response curve and experimental response envelop for average Indian male, affirms the technique used for constructing vibratory model of a standing person. Present work attempts to develop effective technique for constructing subject specific damped vibratory model based on its physical measurements.

  14. Coriolis vibratory gyroscopes theory and design

    CERN Document Server

    Apostolyuk, Vladislav

    2016-01-01

    This book provides the latest theoretical analysis and design methodologies of different types of Coriolis vibratory gyroscopes (CVG). Together, the chapters analyze different types of sensitive element designs and their kinematics, derivation of motion equations, analysis of sensitive elements dynamics in modulated and demodulated signals, calculation and optimization of main performance characteristics, and signal processing and control. Essential aspects of numerical simulation of CVG using Simulink® are also covered. This is an ideal book for graduate students, researchers, and engineers working in fields that require gyroscope application, including but not limited to: inertial sensors and systems, automotive and consumer electronics, small unmanned aircraft control systems, personal mobile navigation systems and related software development, and augmented and virtual reality systems.

  15. Vibratory gyroscopes : identification of mathematical model from test data

    CSIR Research Space (South Africa)

    Shatalov, MY

    2007-05-01

    Full Text Available Simple mathematical model of vibratory gyroscopes imperfections is formulated, which includes anisotropic damping and variation of mass-stiffness parameters and their harmonics. The method of identification of parameters of the mathematical model...

  16. Wave-induced Ship Hull Vibrations in Stochastic Seaways

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Dogliani, M.

    1996-01-01

    A theoretical Study is undertaken on the determination of wave-induced loads in flexible ship hulls. The calculations are performed within the framework of a non-linear, quadratic strip theory formulated in the frequency domain. Included are non-linear effects due to changes in added mass......, hydrodynamic damping and water line breadth with sectional immersion in waves. The study is limited to continuous excitations from the waves and thus transient so-called whipping vibrations due to slamming loads are not considered.Because of the non-linearities the ship hull responses become non...... to the large separation between dominating wave frequencies and the lowest two-node frequency of the hull beam. Both extreme value predictions and fatigue damage are considered.For a fast container ship the rigid body and two-node (springing) vertical wave-induced bending moments amidship are calculated...

  17. Optimization of vibratory welding process parameters using response surface methodology

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Pravin Kumar; Kumar, S. Deepak; Patel, D.; Prasad, S. B. [National Institute of Technology Jamshedpur, Jharkhand (India)

    2017-05-15

    The current investigation was carried out to study the effect of vibratory welding technique on mechanical properties of 6 mm thick butt welded mild steel plates. A new concept of vibratory welding technique has been designed and developed which is capable to transfer vibrations, having resonance frequency of 300 Hz, into the molten weld pool before it solidifies during the Shielded metal arc welding (SMAW) process. The important process parameters of vibratory welding technique namely welding current, welding speed and frequency of the vibrations induced in molten weld pool were optimized using Taguchi’s analysis and Response surface methodology (RSM). The effect of process parameters on tensile strength and hardness were evaluated using optimization techniques. Applying RSM, the effect of vibratory welding parameters on tensile strength and hardness were obtained through two separate regression equations. Results showed that, the most influencing factor for the desired tensile strength and hardness is frequency at its resonance value, i.e. 300 Hz. The micro-hardness and microstructures of the vibratory welded joints were studied in detail and compared with those of conventional SMAW joints. Comparatively, uniform and fine grain structure has been found in vibratory welded joints.

  18. Hull Girder Fatigue Damage Estimations of a Large Container Vessel by Spectral Analysis

    DEFF Research Database (Denmark)

    Andersen, Ingrid Marie Vincent; Jensen, Jørgen Juncher

    2013-01-01

    This paper deals with fatigue damage estimation from the analysis of full-scale stress measurements in the hull of a large container vessel (9,400 TEU) covering several months of operation. For onboard decision support and hull monitoring sys-tems, there is a need for a fast reliable method...... for esti-mation of fatigue damage in the ship hull. The objective of the study is to investigate whether the higher frequency contributions from the hydroelastic responses (springing and whipping) can satisfactory be included in the fatigue damage estimation by only a few parameters derived from the stress...

  19. 14 CFR 25.755 - Hulls.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hulls. 25.755 Section 25.755 Aeronautics... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Floats and Hulls § 25.755 Hulls. (a) Each hull must have enough watertight compartments so that, with any two adjacent compartments flooded, the...

  20. 14 CFR 29.755 - Hull buoyancy.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull buoyancy. 29.755 Section 29.755... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and Hulls § 29.755 Hull buoyancy. Water-based and amphibian rotorcraft. The hull and auxiliary floats, if used, must have enough...

  1. Complex vibratory patterns in an elephant larynx.

    Science.gov (United States)

    Herbst, Christian T; Svec, Jan G; Lohscheller, Jörg; Frey, Roland; Gumpenberger, Michaela; Stoeger, Angela S; Fitch, W Tecumseh

    2013-11-01

    Elephants' low-frequency vocalizations are produced by flow-induced self-sustaining oscillations of laryngeal tissue. To date, little is known in detail about the vibratory phenomena in the elephant larynx. Here, we provide a first descriptive report of the complex oscillatory features found in the excised larynx of a 25 year old female African elephant (Loxodonta africana), the largest animal sound generator ever studied experimentally. Sound production was documented with high-speed video, acoustic measurements, air flow and sound pressure level recordings. The anatomy of the larynx was studied with computed tomography (CT) and dissections. Elephant CT vocal anatomy data were further compared with the anatomy of an adult human male. We observed numerous unusual phenomena, not typically reported in human vocal fold vibrations. Phase delays along both the inferior-superior and anterior-posterior (A-P) dimension were commonly observed, as well as transverse travelling wave patterns along the A-P dimension, previously not documented in the literature. Acoustic energy was mainly created during the instant of glottal opening. The vestibular folds, when adducted, participated in tissue vibration, effectively increasing the generated sound pressure level by 12 dB. The complexity of the observed phenomena is partly attributed to the distinct laryngeal anatomy of the elephant larynx, which is not simply a large-scale version of its human counterpart. Travelling waves may be facilitated by low fundamental frequencies and increased vocal fold tension. A travelling wave model is proposed, to account for three types of phenomena: A-P travelling waves, 'conventional' standing wave patterns, and irregular vocal fold vibration.

  2. Configuration System for Simulation Based Design of Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Hansson, Michael Natapon; Mathiesen, Simon; Ellekilde, Lars-Peter

    2017-01-01

    Vibratory bowl feeders are still among the most commonly used production equipment for automated part feeding, where parts are correctly oriented for further manipulation by being conveyed through a set of orienting devices. Designing vibratory bowl feeders involves selecting and sequencing...... a number of these devices that either reorients or rejects the part until a desirable orientation is achieved. To aid the designer in this task, this work presents a configuration system where knowledge of the behaviour for each device is acquired through dynamic simulation, and used to solve...

  3. Engineering Hydrodynamic AUV Hulls

    Science.gov (United States)

    Allen, J.

    2016-12-01

    AUV stands for autonomous underwater vehicle. AUVs are used in oceanography and are similar to gliders. MBARIs AUVs as well as other AUVs map the ocean floor which is very important. They also measure physical characteristics of the water, such as temperature and salinity. My science fair project for 4th grade was a STEM activity in which I built and tested 3 different AUV bodies. I wanted to find out which design was the most hydrodynamic. I tested three different lengths of AUV hulls to see which AUV would glide the farthest. The first was 6 inches. The second was 12 inches and the third was 18 inches. I used clay for the nosecone and cut a ruler into two and made it the fin. Each AUV used the same nosecone and fin. I tested all three designs in a pool. I used biomimicry to create my hypothesis. When I was researching I found that long slim animals swim fastest. So, my hypothesis is the longer AUV will glide farthest. In the end I was right. The longer AUV did glide the farthest.

  4. General problems of dynamics and control of vibratory gyroscopes

    CSIR Research Space (South Africa)

    Shatalov, MY

    2008-05-01

    Full Text Available A general model of operation of vibratory gyroscopes, which is applicable to a broad class of instruments, including cylindrical, disc and micro-machined gyros, is formulated on the basis of analysis of dynamics and control of a hemispherical...

  5. Dynamics and control of vibratory gyroscopes with special spherical symmetry

    CSIR Research Space (South Africa)

    Shatalov, M

    2006-01-01

    Full Text Available It was shown in 1985 by Acad. V. Zhuravlev that the angular rate of a pure vibrating mode excited in a vibratory gyroscope with spherical symmetry is proportional to an inertial angular rate of the gyroscope. The effect is three dimensional...

  6. Optimisation of Trap Design for Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Sørensen, Lars Carøe; Kraft, Dirk

    2018-01-01

    Vibratory bowl feeders (VBFs) are a widely used option for industrial part feeding, but their design is still largely manual. A subtask of VBF design is determining an optimal parameter set for the passive devices, called traps, which the VBF uses to ensure correct part orientation. This paper...

  7. Evaluation of vibratory ground motion at nuclear power plant sites

    International Nuclear Information System (INIS)

    Hofmann, R.B.; Greeves, J.T.

    1978-01-01

    The evaluation of vibratory ground motion at nuclear power plant sites requires the cooperative effort of scientists and engineers in several disciplines. These include seismology, geology, geotechnical engineering and structural engineering. The Geosciences Branch of the NRC Division of Site Safety and Environmental Analysis includes two sections, the Geology/Seismology Section and the Geotechnical Engineering Section

  8. Strength Tests on Hulls and Floats

    Science.gov (United States)

    Matthaes, K

    1942-01-01

    The present report deals with strength tests on hulls and floats intended in part for the collection of construction data for the design of these components and in part for the stress analysis of the finished hulls and floats.

  9. 46 CFR 115.802 - Hull.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull. 115.802 Section 115.802 Shipping COAST GUARD....802 Hull. (a) At each initial and subsequent inspection for certification of a vessel, the owner or managing operator shall be prepared to conduct tests and have the vessel ready for inspections of the hull...

  10. 46 CFR 176.802 - Hull.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull. 176.802 Section 176.802 Shipping COAST GUARD... CERTIFICATION Material Inspections § 176.802 Hull. (a) At each initial and subsequent inspection for... ready for inspections of the hull structure and its appurtenances, including the following: (1...

  11. 46 CFR 169.239 - Hull.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull. 169.239 Section 169.239 Shipping COAST GUARD... Certification Inspections § 169.239 Hull. At each inspection for certification and periodic inspection, the vessel must be afloat and ready for the following tests and inspections of the hull structure and its...

  12. STUDI KOMPARASI KINERJA HULL FORM METODE SCHELTEMA DENGAN HULL FORM KAPAL IKAN TRADISIONAL TIPE DAERAH BATANG

    OpenAIRE

    A.F. Zakki; Parlindungan Manik

    2012-01-01

    This study comparation of hull form performance was analysed becaused there was suggestion that a ship was built by hull form scheming this time (Scheltema, Formdata, NPL Series) is better than a ship that was built traditionally because there is no basic erudite calculation in hull form design. So hull form design was result of natural adaptation. Such performance are ship’s resistance, stability, and ship’s navigation.This research about hull form performance is expected can giv...

  13. Mechanical Assessment of the Waste Package Subject to Vibratory Motion

    Energy Technology Data Exchange (ETDEWEB)

    M. Gross

    2004-10-14

    The purpose of this document is to provide an integrated overview of the calculation reports that define the response of the waste package and its internals to vibratory ground motion. The calculation reports for waste package response to vibratory ground motion are identified in Table 1-1. Three key calculation reports describe the potential for mechanical damage to the waste package, fuel assemblies, and cladding from a seismic event. Three supporting documents have also been published to investigate sensitivity of damage to various assumptions for the calculations. While these individual reports present information on a specific aspect of waste package and cladding response, they do not describe the interrelationship between the various calculations and the relationship of this information to the seismic scenario class for Total System Performance Assessment-License Application (TSPA-LA). This report is designed to fill this gap by providing an overview of the waste package structural response calculations.

  14. Mechanical Assessment of the Waste Package Subject to Vibratory Motion

    International Nuclear Information System (INIS)

    M. Gross

    2004-01-01

    The purpose of this document is to provide an integrated overview of the calculation reports that define the response of the waste package and its internals to vibratory ground motion. The calculation reports for waste package response to vibratory ground motion are identified in Table 1-1. Three key calculation reports describe the potential for mechanical damage to the waste package, fuel assemblies, and cladding from a seismic event. Three supporting documents have also been published to investigate sensitivity of damage to various assumptions for the calculations. While these individual reports present information on a specific aspect of waste package and cladding response, they do not describe the interrelationship between the various calculations and the relationship of this information to the seismic scenario class for Total System Performance Assessment-License Application (TSPA-LA). This report is designed to fill this gap by providing an overview of the waste package structural response calculations

  15. Vibratory Urticaria Associated with a Missense Variant in ADGRE2.

    Science.gov (United States)

    Boyden, Steven E; Desai, Avanti; Cruse, Glenn; Young, Michael L; Bolan, Hyejeong C; Scott, Linda M; Eisch, A Robin; Long, R Daniel; Lee, Chyi-Chia R; Satorius, Colleen L; Pakstis, Andrew J; Olivera, Ana; Mullikin, James C; Chouery, Eliane; Mégarbané, André; Medlej-Hashim, Myrna; Kidd, Kenneth K; Kastner, Daniel L; Metcalfe, Dean D; Komarow, Hirsh D

    2016-02-18

    Patients with autosomal dominant vibratory urticaria have localized hives and systemic manifestations in response to dermal vibration, with coincident degranulation of mast cells and increased histamine levels in serum. We identified a previously unknown missense substitution in ADGRE2 (also known as EMR2), which was predicted to result in the replacement of cysteine with tyrosine at amino acid position 492 (p.C492Y), as the only nonsynonymous variant cosegregating with vibratory urticaria in two large kindreds. The ADGRE2 receptor undergoes autocatalytic cleavage, producing an extracellular subunit that noncovalently binds a transmembrane subunit. We showed that the variant probably destabilizes an autoinhibitory subunit interaction, sensitizing mast cells to IgE-independent vibration-induced degranulation. (Funded by the National Institutes of Health.).

  16. Characterization of the Bell-Shaped Vibratory Angular Rate Gyro

    Directory of Open Access Journals (Sweden)

    Junfang Fan

    2013-08-01

    Full Text Available The bell-shaped vibratory angular rate gyro (abbreviated as BVG is a novel shell vibratory gyroscope, which is inspired by the Chinese traditional bell. It sensitizes angular velocity through the standing wave precession effect. The bell-shaped resonator is a core component of the BVG and looks like the millimeter-grade Chinese traditional bell, such as QianLong Bell and Yongle Bell. It is made of Ni43CrTi, which is a constant modulus alloy. The exciting element, control element and detection element are uniformly distributed and attached to the resonator, respectively. This work presents the design, analysis and experimentation on the BVG. It is most important to analyze the vibratory character of the bell-shaped resonator. The strain equation, internal force and the resonator's equilibrium differential equation are derived in the orthogonal curvilinear coordinate system. When the input angular velocity is existent on the sensitive axis, an analysis of the vibratory character is performed using the theory of thin shells. On this basis, the mode shape function and the simplified second order normal vibration mode dynamical equation are obtained. The coriolis coupling relationship about the primary mode and secondary mode is established. The methods of the signal processing and control loop are presented. Analyzing the impact resistance property of the bell-shaped resonator, which is compared with other shell resonators using the Finite Element Method, demonstrates that BVG has the advantage of a better impact resistance property. A reasonable means of installation and a prototypal gyro are designed. The gyroscopic effect of the BVG is characterized through experiments. Experimental results show that the BVG has not only the advantages of low cost, low power, long work life, high sensitivity, and so on, but, also, of a simple structure and a better impact resistance property for low and medium angular velocity measurements.

  17. Innovative decontamination technology by abrasion in vibratory vessels

    International Nuclear Information System (INIS)

    Fabbri, Silvio; Ilarri, Sergio

    2007-01-01

    Available in abstract form only. Full text of publication follows: The possibility of using conventional vibratory vessel technology as a decontamination technique is the motivation for the development of this project. The objective is to explore the feasibility of applying the vibratory vessel technology for decontamination of radioactively-contaminated materials such as pipes and metal structures. The research and development of this technology was granted by the U.S. Department of Energy (DOE). Abrasion processes in vibratory vessels are widely used in the manufacture of metals, ceramics, and plastics. Samples to be treated, solid abrasive media and liquid media are set up into a vessel. Erosion results from the repeated impact of the abrasive particles on the surface of the body being treated. A liquid media, generally detergents or surfactants aid the abrasive action. The amount of material removed increases with the time of treatment. The design and construction of the machine were provided by Vibro, Argentina private company. Tests with radioactively-contaminated aluminum tubes and a stainless steel bar, were performed at laboratory level. Tests showed that it is possible to clean both the external and the internal surface of contaminated tubes. Results show a decontamination factor around 10 after the first 30 minutes of the cleaning time. (authors)

  18. 46 CFR 45.129 - Hull fittings: General.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Hull fittings: General. 45.129 Section 45.129 Shipping... Assignment § 45.129 Hull fittings: General. Hull fittings must be securely mounted in the hull so as to avoid increases in hull stresses and must be protected from local damage caused by movement of equipment or cargo. ...

  19. 46 CFR 154.174 - Transverse contiguous hull structure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Transverse contiguous hull structure. 154.174 Section... Equipment Hull Structure § 154.174 Transverse contiguous hull structure. (a) The transverse contiguous hull...) The transverse contiguous hull structure of a vessel having cargo containment systems with secondary...

  20. 46 CFR 115.645 - Alternative Hull Examination (AHE) Procedure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) Procedure. 115.645... AND CERTIFICATION Hull and Tailshaft Examinations § 115.645 Alternative Hull Examination (AHE... underwater hull plating and a detailed examination of all hull welds, propellers, tailshafts, rudders, and...

  1. 46 CFR 172.085 - Hull type.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull type. 172.085 Section 172.085 Shipping COAST GUARD... of This Chapter § 172.085 Hull type. If a cargo listed in Table 151.05 of part 151 of this chapter is to be carried, the tank barge must be at least the hull type specified in Table 151.05 of this...

  2. 33 CFR 110.31 - Hull Bay and Allerton Harbor at Hull, Mass.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Hull Bay and Allerton Harbor at Hull, Mass. 110.31 Section 110.31 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.31 Hull Bay and Allerton Harbor at...

  3. Used Furan Sand Reclamation in REGMAS Vibratory Unit

    Directory of Open Access Journals (Sweden)

    Dańko J.

    2015-09-01

    Full Text Available The paper, especially dealt with problems of reclamation of used furan sand, carried out in new, vibratory sand reclamation unit REGMAS developed by researches from AGH-University of Science and Technology, Faculty of Foundry Engineering in Cracow (Poland. Functional characteristics of reclamation unit as well as the results of reclamation of used sand with furfuryl resin are discussed in the paper. The quality of reclaim was tested by means of the LOI and pH value, dust content in the reclaim and at least by the the quality of the castings produced in moulds prepared with the use of reclaimed matrix.

  4. Automation Selection and Sequencing of Traps for Vibratory Feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Ellekilde, Lars-Peter

    2017-01-01

    Vibratory parts feeders with mechanical orienting devices are used extensively in the assembly automation industry. Even so, the design process is based on trial-and-error approaches and is largely manual. In this paper, a methodology is presented for automatic design of this type of feeder....... The approach uses dynamic simulation for generating the necessary data for configuring a feeder with a sequence of mechanical orienting devices called traps, with the goal of reorienting all parts from a random to fixed orientation. Then, a fast algorithm for facilitating this configuration task automatically...

  5. Field Tests to Investigate the Penetration Rate of Piles Driven by Vibratory Installation

    Directory of Open Access Journals (Sweden)

    Zhaohui Qin

    2017-01-01

    Full Text Available Factors directly affecting the penetration rate of piles installed by vibratory driving technique are summarized and classified into seven aspects which are driving force, resistance, vibratory amplitude, energy consumption, speeding up at the beginning, pile plumbness keeping, and slowing down at the end, from the mechanism and engineering practice of the vibratory pile driving. In order to find out how these factors affect the penetration rate of the pile in three major actors of vibratory pile driving: (i the pile to be driven, (ii the selected driving system, and (iii the imposed soil conditions, field tests on steel sheet piles driven by vibratory driving technique in different soil conditions are conducted. The penetration rates of three different sheet pile types having up to four different lengths installed using two different vibratory driving systems are documented. Piles with different lengths and types driven with or without clutch have different penetration rates. The working parameters of vibratory hammer, such as driving force and vibratory amplitude, have great influences on the penetration rate of the pile, especially at the later stages of the sinking process. Penetration rate of piles driven in different soil conditions is uniform because of the different penetration resistance including shaft friction and toe resistance.

  6. 46 CFR 185.602 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull markings. 185.602 Section 185.602 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) OPERATIONS Markings Required § 185.602 Hull markings. (a) Each vessel must be marked as required by part 67...

  7. 46 CFR 122.602 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull markings. 122.602 Section 122.602 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150....602 Hull markings. (a) Each vessel must be marked as required by part 67, subpart I, of this chapter...

  8. Spring in the Arab Spring

    NARCIS (Netherlands)

    Borg, G.J.A.

    2011-01-01

    Column Gert Borg | Spring in the Arab Spring door dr. Gert Borg, onderzoeker bij Islam en Arabisch aan de Radboud Universiteit Nijmegen en voormalig directeur van het Nederlands-Vlaams Instituut Caïro Spring If, in Google, you type "Arab Spring" and hit the button, you get more than

  9. Designing and testing a laser-based vibratory sensor

    Science.gov (United States)

    Nath, G.

    2018-04-01

    Sensor technology has proved its importance, not only in the range of few-meter applications in different fields, but in micro, nano, atomic and sub-atomic-sized objects. The present work describes the designing of a laser-based vibratory sensor using a He-Ne laser as the signal source. The received characteristics of the signal are mainly the frequency and amplitude of the vibration from which the physical parameters such as energy, power and absorption coefficients of the material are determined, which enables us to provide information of the hidden target or object. This laboratory-designed sensor finds application in different local phenomena as well as laboratory practical activity for students.

  10. 46 CFR 45.153 - Through-hull piping: General.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Through-hull piping: General. 45.153 Section 45.153... Conditions of Assignment § 45.153 Through-hull piping: General. (a) All through-hull pipes required by this subpart must be made of steel or material equivalent to the hull in strength and fatigue resistance. (b...

  11. 46 CFR 154.176 - Longitudinal contiguous hull structure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Longitudinal contiguous hull structure. 154.176 Section... Equipment Hull Structure § 154.176 Longitudinal contiguous hull structure. (a) The longitudinal contiguous hull structure of a vessel having cargo containment systems without secondary barriers must meet the...

  12. 46 CFR 154.178 - Contiguous hull structure: Heating system.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous hull structure: Heating system. 154.178... Equipment Hull Structure § 154.178 Contiguous hull structure: Heating system. The heating system for transverse and longitudinal contiguous hull structure must: (a) Be shown by a heat load calculation to have...

  13. 46 CFR 154.180 - Contiguous hull structure: Welding procedure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous hull structure: Welding procedure. 154.180... Equipment Hull Structure § 154.180 Contiguous hull structure: Welding procedure. Welding procedure tests for contiguous hull structure designed for a temperature colder than −18 °C (0 °F) must meet § 54.05-15 and...

  14. 14 CFR 29.757 - Hull and auxiliary float strength.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and auxiliary float strength. 29.757... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and Hulls § 29.757 Hull and auxiliary float strength. The hull, and auxiliary floats if used, must withstand the...

  15. 46 CFR 151.10-20 - Hull construction.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Hull construction. 151.10-20 Section 151.10-20 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Barge Hull Construction Requirements § 151.10-20 Hull construction. (a) Construction features. (1) Each barge hull shall be constructed with a suitable bow form...

  16. 46 CFR 151.10-1 - Barge hull classifications.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Barge hull classifications. 151.10-1 Section 151.10-1... CARRYING BULK LIQUID HAZARDOUS MATERIAL CARGOES Barge Hull Construction Requirements § 151.10-1 Barge hull classifications. (a) Each barge constructed or converted in conformance with this subpart shall be assigned a hull...

  17. 46 CFR 115.655 - Hull examination reports.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull examination reports. 115.655 Section 115.655... CERTIFICATION Hull and Tailshaft Examinations § 115.655 Hull examination reports. (a) If you use only divers for the underwater survey portion of the Alternative Hull Examination (AHE), you must provide the Officer...

  18. 46 CFR 154.188 - Membrane tank: Inner hull steel.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Membrane tank: Inner hull steel. 154.188 Section 154.188... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Hull Structure § 154.188 Membrane tank: Inner hull steel. For a vessel with membrane tanks, the inner hull...

  19. 46 CFR 176.655 - Hull examination reports.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull examination reports. 176.655 Section 176.655... TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.655 Hull examination reports. (a) If you use only divers for the underwater survey portion of the Alternative Hull Examination (AHE...

  20. 21 CFR 573.160 - Ammoniated rice hulls.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ammoniated rice hulls. 573.160 Section 573.160... Additive Listing § 573.160 Ammoniated rice hulls. The food additive ammoniated rice hulls may be safely... obtained by the treatment of ground rice hulls with monocalcium phosphate and anhydrous ammonia at a...

  1. A new approach to hull consistency

    Directory of Open Access Journals (Sweden)

    Kolev Lubomir

    2016-06-01

    Full Text Available Hull consistency is a known technique to improve the efficiency of iterative interval methods for solving nonlinear systems describing steady-states in various circuits. Presently, hull consistency is checked in a scalar manner, i.e. successively for each equation of the nonlinear system with respect to a single variable. In the present poster, a new more general approach to implementing hull consistency is suggested which consists in treating simultaneously several equations with respect to the same number of variables.

  2. Global Loads on FRP Ship Hulls

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup

    1997-01-01

    Fibre reinforced plastic (FRP) composites used for high-speed vessels have lower modulus of elasticity than the conventionally used steels.Therefore, for large fast ships the lowest natural frequencies of the global hull modes can be relatively low compared to the frequency of waveencounter....... As part of the NoKoS project it was decided to investigate the effect of hull flexibility on the wave-induced as well as accidental structural loads on high-speed ships.Especially it was decided to determine whether there is an upper size of FRP and aluminium mono-hulls caused by continuous wave action...

  3. The Numerical FEM Model of the Kinematics of the Vibratory Shot Peening Process

    Directory of Open Access Journals (Sweden)

    Stanisław Bławucki

    2017-12-01

    Full Text Available The paper presents the results of numerical calculations, with the finite element method in the ABAQUS program environment, of the vibratory shot peening process with loose peening elements. The behaviour of shot peening elements was analysed in the kinematic aspect. The impact of the initial deployment of vibratory shot peening elements on their behaviour during processing was investigated, including the displacement, velocity, acceleration and the number of collisions. The way of determining the effectiveness of the processing with the vibratory shot peening was illustrated.

  4. Hull's Diploma in Teaching of Adults

    Science.gov (United States)

    Styler, W. E.

    1971-01-01

    A diploma in the Teaching of Adults for part-time students was introduced in the University of Hull in 1966 as a fully recognized university diploma. Article discusses the three major parts of the course, examinations, and requirements. (RB)

  5. Morphing hull implementation for unmanned underwater vehicles

    Science.gov (United States)

    Miller, Timothy F.; Gandhi, Farhan; Rufino, Russell J.

    2013-11-01

    There has been much interest and work in the area of morphing aircraft since the 1980s. Morphing could also potentially benefit unmanned underwater vehicles (UUVs). The current paper envisions a UUV with an interior pressure hull and a variable diameter outer flexible hull with fuel stored in the annulus between, and presents a mechanism to realize diameter change of the outer hull. The outer hull diameter of UUVs designed for very long endurance/range could be progressively reduced as fuel was consumed, thereby reducing drag and further increasing endurance and range capability. Diameter morphing could also be advantageous for compact storage of UUVs. A prototype is fabricated to represent an axial section of such a morphing diameter UUV. Diameter change is achieved using eight morphing trusses arranged equidistant around the circumference of the representative interior rigid hull. Each morphing truss has a lower rail (attached to the rigid hull) and an upper rail with V-linkages between, at either ends of the rail. Horizontal motion of the feet of the V-linkages (sliding in the lower rail) results in vertical motion of the upper rail which in turn produces diameter change of the outer hull. For the prototype built and tested, a 63% increase in outer diameter from 12.75″ to 20.75″ was achieved. The introduction of a stretched latex representative flexible skin around the outer rails increased actuation force requirement and led to a propensity for the wheel-in-track sliders in the morphing truss to bind. It is anticipated that this could be overcome with higher precision manufacturing. In addition to symmetric actuation of the morphing trusses resulting in diameter change, the paper also shows that with asymmetric actuation the hull cross-section shape can be changed (for example, from a circular section for underwater operation to a V-section for surface operations).

  6. Morphing hull implementation for unmanned underwater vehicles

    International Nuclear Information System (INIS)

    Miller, Timothy F; Gandhi, Farhan; Rufino, Russell J

    2013-01-01

    There has been much interest and work in the area of morphing aircraft since the 1980s. Morphing could also potentially benefit unmanned underwater vehicles (UUVs). The current paper envisions a UUV with an interior pressure hull and a variable diameter outer flexible hull with fuel stored in the annulus between, and presents a mechanism to realize diameter change of the outer hull. The outer hull diameter of UUVs designed for very long endurance/range could be progressively reduced as fuel was consumed, thereby reducing drag and further increasing endurance and range capability. Diameter morphing could also be advantageous for compact storage of UUVs. A prototype is fabricated to represent an axial section of such a morphing diameter UUV. Diameter change is achieved using eight morphing trusses arranged equidistant around the circumference of the representative interior rigid hull. Each morphing truss has a lower rail (attached to the rigid hull) and an upper rail with V-linkages between, at either ends of the rail. Horizontal motion of the feet of the V-linkages (sliding in the lower rail) results in vertical motion of the upper rail which in turn produces diameter change of the outer hull. For the prototype built and tested, a 63% increase in outer diameter from 12.75″ to 20.75″ was achieved. The introduction of a stretched latex representative flexible skin around the outer rails increased actuation force requirement and led to a propensity for the wheel-in-track sliders in the morphing truss to bind. It is anticipated that this could be overcome with higher precision manufacturing. In addition to symmetric actuation of the morphing trusses resulting in diameter change, the paper also shows that with asymmetric actuation the hull cross-section shape can be changed (for example, from a circular section for underwater operation to a V-section for surface operations). (paper)

  7. Inspecting the inside of underwater hull

    Science.gov (United States)

    Valkovic, Vladivoj; Sudac, Davorin

    2009-05-01

    In order to demonstrate the possibility of identifying the material within ship's underwater hull, sunken ships and other objects on the sea floor tests with the 14 MeV sealed tube neutron generator incorporated inside a small submarine submerged in the test basin filled with sea water have been performed. Results obtained for inspection of diesel fuel and explosive presence behind single and double hull constructions are presented.

  8. A Review on Solidification and Change in Mechanical Properties Under Vibratory Welding Condition

    OpenAIRE

    Jyoti Prakash; Dr. S.P. Tewari; Bipin Kumar Srivastava

    2010-01-01

    Welding has been applied to various industries in particular, automotive, aerospace and microelectronics. Thermal cycle produced near weld line generates residual stress and inhomogeneous plastic deformation in weldments. However there are many methods for welding the workpieces and one of the method among these is vibratory welding. It has the advantages of less investment, more convenient operation, less pollution and shorter manufacturing period. In vibratory welding, workpiece vibrates in...

  9. CFD simulation on Kappel propeller with a hull wake field

    DEFF Research Database (Denmark)

    Shin, Keun Woo; Andersen, Poul; Møller Bering, Rasmus

    2013-01-01

    Marine propellers are designed not for the open-water operation, but for the operation behind a hull due to the inhomogeneous hull wake and thrust deduction. The adaptation for the hull wake is important for the propulsive efficiency and cavitation risk especially on single-screw ships. CFD...... simulations for a propeller with a hull model have showed acceptable agreement with a model test result in the thrust and torque (Larsson et al. 2010). In the current work, a measured hull wake is applied to the simulation instead of modelling a hull, because the hull geometry is mostly not available...... for propeller designers and the computational effort can be reduced by excluding the hull. The CFD simulation of a propeller flow with a hull wake is verified in order to use CFD as a propeller design tool. A Kappel propeller, which is an innovative tip-modified propeller, is handled. Kappel propellers...

  10. Spring Tire

    Science.gov (United States)

    Asnani, Vivake M.; Benzing, Jim; Kish, Jim C.

    2011-01-01

    The spring tire is made from helical springs, requires no air or rubber, and consumes nearly zero energy. The tire design provides greater traction in sandy and/or rocky soil, can operate in microgravity and under harsh conditions (vastly varying temperatures), and is non-pneumatic. Like any tire, the spring tire is approximately a toroidal-shaped object intended to be mounted on a transportation wheel. Its basic function is also similar to a traditional tire, in that the spring tire contours to the surface on which it is driven to facilitate traction, and to reduce the transmission of vibration to the vehicle. The essential difference between other tires and the spring tire is the use of helical springs to support and/or distribute load. They are coiled wires that deform elastically under load with little energy loss.

  11. Just Spring

    CERN Document Server

    Konda, Madhusudhan

    2011-01-01

    Get a concise introduction to Spring, the increasingly popular open source framework for building lightweight enterprise applications on the Java platform. This example-driven book for Java developers delves into the framework's basic features, as well as advanced concepts such as containers. You'll learn how Spring makes Java Messaging Service easier to work with, and how its support for Hibernate helps you work with data persistence and retrieval. Throughout Just Spring, you'll get your hands deep into sample code, beginning with a problem that illustrates dependency injection, Spring's co

  12. Beginning Spring

    CERN Document Server

    Caliskan, Mert

    2015-01-01

    Get up to speed quickly with this comprehensive guide toSpring Beginning Spring is the complete beginner's guide toJava's most popular framework. Written with an eye towardreal-world enterprises, the book covers all aspects of applicationdevelopment within the Spring Framework. Extensive samples withineach chapter allow developers to get up to speed quickly byproviding concrete references for experimentation, building askillset that drives successful application development byexploiting the full capabilities of Java's latest advances. Spring provides the exact toolset required to build anent

  13. Experimental investigations of higher-order springing and whipping-WILS project

    Directory of Open Access Journals (Sweden)

    Hong Sa Young

    2014-12-01

    Full Text Available Springing and whipping are becoming increasingly important considerations in ship design as container ships increase in size. In this study, the springing and whipping characteristics of a large container ship were investigated through a series of systematic model tests in waves. A multi-segmented hull model with a backbone was adopted for measurement of springing and whipping signals. A conversion method for extracting torsion springing and whipping is described in this paper for the case of an open-section backbone. Higher-order springing, higher-mode torsion responses, and the effects of linear and nonlinear springing in irregular waves are highlighted in the discussion.

  14. Region-of-interest volumetric visual hull refinement

    KAUST Repository

    Knoblauch, Daniel; Kuester, Falko

    2010-01-01

    This paper introduces a region-of-interest visual hull refinement technique, based on flexible voxel grids for volumetric visual hull reconstructions. Region-of-interest refinement is based on a multipass process, beginning with a focussed visual

  15. Development and evaluation of a vibratory-pneumatic pomegranate arils extractor

    Directory of Open Access Journals (Sweden)

    S. M Nassiri

    2017-05-01

    Full Text Available Introduction Iran is a frontier of pomegranate fruit production in the world (with almost 40 % of the world`s production. However due to traditional processing operations is not ranked as the largest pomegranate exporter. Saveh, Neyriz and Ferdows are the top pomegranate producing cities in Iran. Pomegranate is consumed as a fresh fruit as well as processed product as food additive, paste, syrup, jelly, pectin, jam, beverage, essence, vinegar and concentrate. Aril extraction is the first and essential postharvest operation for pomegranate processing. Arils are mostly extracted manually even in large scales for fresh and processed consumption. This labor intensive operation is rational when aril quality is an important index for consumer. But whenever pomegranate juice is desired, the aril quality has no priority for consumer, and therefore arils can be extracted with less care. Sarig (1985 was the first inventor of a pomegranate aril extractor who employed air jet force to extract the arils. Later, other researchers employed the same method as well as water jet to extract fruit juice and sac. In the present study, fabrication and evaluation of vibratory aril extractor augmented with air system was conducted. Materials and Methods The study was conducted using Rabab cultivar samples which were manually harvested from an orchard in Neyriz town, Fars province. Samples were kept in refrigerator at 5 0C till experimental trials. Initial moisture content of fruit skin, arils and internal fleshes were measured by gravimetric method as 31.7±2.6 %, 61.5±1.8 % and 42.8±1.4 %, respectively and for a whole fruit was measured 45.3±11.5 % (w.b.. For conducting laboratory tests, an aril extraction unit was designed and fabricated. It comprised a steel main frame, a 746 W electric motor, drive mechanism (eccentric and shaft, sample retentive unit, air jet unit, aril tank, and an air compressor-tank assembly. Sample retentive unit was designed in such a

  16. Management of cladding hulls and fuel hardware

    International Nuclear Information System (INIS)

    1985-01-01

    The reprocessing of spent fuel from power reactors based on chop-leach technology produces a solid waste product of cladding hulls and other metallic residues. This report describes the current situation in the management of fuel cladding hulls and hardware. Information is presented on the material composition of such waste together with the heating effects due to neutron-induced activation products and fuel contamination. As no country has established a final disposal route and the corresponding repository, this report also discusses possible disposal routes and various disposal options under consideration at present

  17. Obtaining high purity silica from rice hulls

    Directory of Open Access Journals (Sweden)

    José da Silva Júnior

    2010-01-01

    Full Text Available Many routes for extracting silica from rice hulls are based on direct calcining. These methods, though, often produce silica contaminated with inorganic impurities. This work presents the study of a strategy for obtaining silica from rice hulls with a purity level adequate for applications in electronics. The technique is based on two leaching steps, using respectively aqua regia and Piranha solutions, which extract the organic matrix and inorganic impurities. The material was characterized by Fourier-transform infrared spectroscopy (FTIR, powder x-ray diffraction (XRD, x-ray fluorescence (XRF, scanning electron microscopy (SEM, particle size analysis by laser diffraction (LPSA and thermal analysis.

  18. 46 CFR 91.25-25 - Hull equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull equipment. 91.25-25 Section 91.25-25 Shipping COAST... CERTIFICATION Inspection for Certification § 91.25-25 Hull equipment. (a) At each inspection for certification and periodic inspection, the inspectors shall conduct the following tests and inspections of hull...

  19. 46 CFR 169.231 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 169.231... hull examinations. As used in the part— (a) Drydock examination means hauling out a vessel or placing a... and all through-hull fittings, sea chests, sea valves, sea strainers, and valves for the emergency...

  20. 33 CFR 181.25 - Hull identification number format.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hull identification number format... (CONTINUED) BOATING SAFETY MANUFACTURER REQUIREMENTS Identification of Boats § 181.25 Hull identification number format. Each of the hull identification numbers required by § 181.23 must consist of twelve...

  1. 46 CFR 45.107 - Strength of hull.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Strength of hull. 45.107 Section 45.107 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.107 Strength of hull. The general structural strength of the hull must be sufficient for the...

  2. 46 CFR 154.170 - Outer hull steel plating.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Outer hull steel plating. 154.170 Section 154.170... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Hull Structure § 154.170 Outer hull steel plating. (a) Except as required in paragraph (b) of this section, the...

  3. 46 CFR 154.516 - Piping: Hull protection.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Piping: Hull protection. 154.516 Section 154.516 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY... and Process Piping Systems § 154.516 Piping: Hull protection. A vessel's hull must be protected from...

  4. 33 CFR 181.29 - Hull identification number display.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hull identification number... SECURITY (CONTINUED) BOATING SAFETY MANUFACTURER REQUIREMENTS Identification of Boats § 181.29 Hull identification number display. Two identical hull identification numbers are required to be displayed on each...

  5. 46 CFR 71.50-29 - Hull examination reports.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Hull examination reports. 71.50-29 Section 71.50-29... CERTIFICATION Drydocking § 71.50-29 Hull examination reports. (a) If you use only divers for the underwater survey portion of the Alternative Hull Examination (AHE), you must provide the Officer in Charge, Marine...

  6. 46 CFR 154.172 - Contiguous steel hull structure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Hull Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this...

  7. 46 CFR 111.05-11 - Hull return.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull return. 111.05-11 Section 111.05-11 Shipping COAST... REQUIREMENTS Equipment Ground, Ground Detection, and Grounded Systems § 111.05-11 Hull return. (a) A vessel's hull must not carry current as a conductor except for the following systems: (1) Impressed current...

  8. 46 CFR 252.33 - Hull and machinery insurance.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Hull and machinery insurance. 252.33 Section 252.33... Subsidy Rates § 252.33 Hull and machinery insurance. (a) Subsidy items. The fair and reasonable net premium costs (including stamp taxes) of hull and machinery, increased value, excess general average...

  9. 46 CFR 189.25-25 - Hull equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull equipment. 189.25-25 Section 189.25-25 Shipping... CERTIFICATION Inspection for Certification § 189.25-25 Hull equipment. (a) At each inspection for certification and periodic inspection the inspector shall conduct the following tests and inspections of hull...

  10. 33 CFR 181.23 - Hull identification numbers required.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hull identification numbers... SECURITY (CONTINUED) BOATING SAFETY MANUFACTURER REQUIREMENTS Identification of Boats § 181.23 Hull... identify each boat produced or imported with two hull identification numbers that meet the requirements of...

  11. 46 CFR 71.25-25 - Hull equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Hull equipment. 71.25-25 Section 71.25-25 Shipping COAST... Inspection § 71.25-25 Hull equipment. (a) At each annual inspection, the inspector shall conduct the following tests and inspections of hull equipment: (1) All subdivision bulkheads shall be examined to...

  12. 46 CFR 308.107 - War risk hull insurance policy.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false War risk hull insurance policy. 308.107 Section 308.107 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Hull and Disbursements Insurance § 308.107 War risk hull insurance policy. Standard Form MA-240...

  13. 46 CFR 282.23 - Hull and machinery insurance.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Hull and machinery insurance. 282.23 Section 282.23... COMMERCE OF THE UNITED STATES Calculation of Subsidy Rates § 282.23 Hull and machinery insurance. (a) Subsidy items. The fair and reasonable net premium costs (including stamp taxes) of hull and machinery...

  14. RANS simulation of cavitation and hull pressure fluctuation for marine propeller operating behind-hull condition

    Science.gov (United States)

    Paik, Kwang-Jun; Park, Hyung-Gil; Seo, Jongsoo

    2013-12-01

    Simulations of cavitation flow and hull pressure fluctuation for a marine propeller operating behind a hull using the unsteady Reynolds-Averaged Navier-Stokes equations (RANS) are presented. A full hull body submerged under the free surface is modeled in the computational domain to simulate directly the wake field of the ship at the propeller plane. Simulations are performed in design and ballast draught conditions to study the effect of cavitation number. And two propellers with slightly different geometry are simulated to validate the detectability of the numerical simulation. All simulations are performed using a commercial CFD software FLUENT. Cavitation patterns of the simulations show good agreement with the experimental results carried out in Samsung CAvitation Tunnel (SCAT). The simulation results for the hull pressure fluctuation induced by a propeller are also compared with the experimental results showing good agreement in the tendency and amplitude, especially, for the first blade frequency.

  15. RANS simulation of cavitation and hull pressure fluctuation for marine propeller operating behind-hull condition

    Directory of Open Access Journals (Sweden)

    Kwang-Jun Paik

    2013-12-01

    Full Text Available Simulations of cavitation flow and hull pressure fluctuation for a marine propeller operating behind a hull using the unsteady Reynolds-Averaged Navier-Stokes equations (RANS are presented. A full hull body submerged under the free surface is modeled in the computational domain to simulate directly the wake field of the ship at the propeller plane. Simulations are performed in design and ballast draught conditions to study the effect of cavitation number. And two propellers with slightly different geometry are simulated to validate the detectability of the numerical simulation. All simulations are performed using a commercial CFD software FLUENT. Cavitation patterns of the simulations show good agreement with the experimental results carried out in Samsung CAvitation Tunnel (SCAT. The simulation results for the hull pressure fluctuation induced by a propeller are also compared with the experimental results showing good agreement in the tendency and amplitude, especially, for the first blade frequency.

  16. Ultimate Strength of Ship Hulls under Torsion

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Thayamballi, Anil K.; Pedersen, Preben Terndrup

    2001-01-01

    For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength characte......For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength...... characteristics of ships with large hatch openings. The primary aim of the present study is to investigate the ultimate strength characteristics of ship hulls with large hatch openings under torsion. Axial (warping) as well as shear stresses are normally developed for thin-walled beams with open cross sections...... subjected to torsion. A procedure for calculating these stresses is briefly described. As an illustrative example, the distribution and magnitude of warping and shear stresses for a typical container vessel hull cross section under unit torsion is calculated by the procedure. By theoretical and numerical...

  17. Rhythmical Alchemy: Village Drumming with Arthur Hull.

    Science.gov (United States)

    Hillerson, Gary R.; Hull, Arthur

    As a step toward writing a master's thesis in psychology, the connection between rhythm circles and psychotherapeutic process was explored. Arthur Hull, who experienced and preached about the healing power of rhythm for many years, was interviewed. This article recorded the interview between Arthur and the researcher. The interviewer learned that…

  18. "Keisri hull" on viimast korda laval

    Index Scriptorium Estoniae

    2010-01-01

    Neli hooaega Ugala repertuaaris olnud Jaan Krossi romaani põhjal lavastatud draama "Keisri hull" etendub viimast korda 10. veebruaril. Viimane etendus on pühendatud Jaan Krossi 90. sünniaastapäevale, mis on 19. veebruaril. Lavastajad Peeter Tammearu ja Jaak Allik. Peaosas Peeter Tammearu

  19. Committee VI.1. Extreme Hull Girder Loading

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher

    2000-01-01

    Committee Mandate. Evaluate and develop direct calculation procedures for extreme wawe loads on ship hull girders. Due consideration shall be given to stochastic and non-linear effects. The procedures shall be assessed by comparison with in-service experiences, model tests and more refined...

  20. Convex Hull Aided Registration Method (CHARM).

    Science.gov (United States)

    Fan, Jingfan; Yang, Jian; Zhao, Yitian; Ai, Danni; Liu, Yonghuai; Wang, Ge; Wang, Yongtian

    2017-09-01

    Non-rigid registration finds many applications such as photogrammetry, motion tracking, model retrieval, and object recognition. In this paper we propose a novel convex hull aided registration method (CHARM) to match two point sets subject to a non-rigid transformation. First, two convex hulls are extracted from the source and target respectively. Then, all points of the point sets are projected onto the reference plane through each triangular facet of the hulls. From these projections, invariant features are extracted and matched optimally. The matched feature point pairs are mapped back onto the triangular facets of the convex hulls to remove outliers that are outside any relevant triangular facet. The rigid transformation from the source to the target is robustly estimated by the random sample consensus (RANSAC) scheme through minimizing the distance between the matched feature point pairs. Finally, these feature points are utilized as the control points to achieve non-rigid deformation in the form of thin-plate spline of the entire source point set towards the target one. The experimental results based on both synthetic and real data show that the proposed algorithm outperforms several state-of-the-art ones with respect to sampling, rotational angle, and data noise. In addition, the proposed CHARM algorithm also shows higher computational efficiency compared to these methods.

  1. Estimation of penetration depth of fission products in cladding Hull

    International Nuclear Information System (INIS)

    Kim, Hee Moon; Jung, Yang Hong; Yoo, Byong Ok; Choo, Yong Sun; Hong, Kwon Pyo

    2005-01-01

    A disposal and a reprocessing for spent fuel rod with high burnup need de-cladding procedure. Pellet in this rod has been separated from a cladding hull to reduce a radioactivity of hull by chemical and mechanical methods. But fission products and actinides(U,Pu) still remain inside of cladding hull by chemical bonding and fission spike, which is called as 'contamination'. More specific removal of this contamination would have been considered. In this study, the sorts of fission products and penetration depth in hull were observed by EPMA test. To analyze this behavior, SRIM 2000 code was also used as energies of fission products and an oxide thickness of hull

  2. Motions and Hull-Induced Bridging-Structure Loads for a Small Waterplane Area, Twin-Hulled, Attack Aircraft Carrier in Waves

    National Research Council Canada - National Science Library

    Jones, Harry D; Gerzina, David M

    1973-01-01

    ... small waterplane area, twin-hulled, attack aircraft carrier in waves. Motions of the model were measured, together with the forces and moments induced by the hulls on the cross structure spanning the two hulls...

  3. Spring performance tester for miniature extension springs

    Science.gov (United States)

    Salzbrenner, Bradley; Boyce, Brad

    2017-05-16

    A spring performance tester and method of testing a spring are disclosed that has improved accuracy and precision over prior art spring testers. The tester can perform static and cyclic testing. The spring tester can provide validation for product acceptance as well as test for cyclic degradation of springs, such as the change in the spring rate and fatigue failure.

  4. DECONTAMINATION OF ZIRCALOY SPENT FUEL CLADDING HULLS

    International Nuclear Information System (INIS)

    Rudisill, T; John Mickalonis, J

    2006-01-01

    The reprocessing of commercial spent nuclear fuel (SNF) generates a Zircaloy cladding hull waste which requires disposal as a high level waste in the geologic repository. The hulls are primarily contaminated with fission products and actinides from the fuel. During fuel irradiation, these contaminants are deposited in a thin layer of zirconium oxide (ZrO 2 ) which forms on the cladding surface at the elevated temperatures present in a nuclear reactor. Therefore, if the hulls are treated to remove the ZrO 2 layer, a majority of the contamination will be removed and the hulls could potentially meet acceptance criteria for disposal as a low level waste (LLW). Discard of the hulls as a LLW would result in significant savings due to the high costs associated with geologic disposal. To assess the feasibility of decontaminating spent fuel cladding hulls, two treatment processes developed for dissolving fuels containing zirconium (Zr) metal or alloys were evaluated. Small-scale dissolution experiments were performed using the ZIRFLEX process which employs a boiling ammonium fluoride (NH 4 F)/ammonium nitrate (NH 4 NO 3 ) solution to dissolve Zr or Zircaloy cladding and a hydrofluoric acid (HF) process developed for complete dissolution of Zr-containing fuels. The feasibility experiments were performed using Zircaloy-4 metal coupons which were electrochemically oxidized to produce a thin ZrO 2 layer on the surface. Once the oxide layer was in place, the ease of removing the layer using methods based on the two processes was evaluated. The ZIRFLEX and HF dissolution processes were both successful in removing a 0.2 mm (thick) oxide layer from Zircaloy-4 coupons. Although the ZIRFLEX process was effective in removing the oxide layer, two potential shortcomings were identified. The formation of ammonium hexafluorozirconate ((NH 4 ) 2 ZrF 6 ) on the metal surface prior to dissolution in the bulk solution could hinder the decontamination process by obstructing the removal of

  5. ANALYSIS OF VIBRATORY PROTECTION SYSTEM VIBRATION DURING HARMONIC AND POLYHARMONIC EXCITATIONS

    Directory of Open Access Journals (Sweden)

    T. N. Mikulik

    2011-01-01

    Full Text Available The paper considers a mathematical model of local «driver-seat» system and an algorithm for vibratory loading formation at external actions. Results of the investigations on the system vibration according to minimum vibration acceleration depending on transfer force factor acting on the seat and a vibration isolation factor are presented in the paper.

  6. Penile vibratory stimulation in the treatment of post-prostatectomy incontinence

    DEFF Research Database (Denmark)

    Fode, Mikkel; Sønksen, Jens

    2015-01-01

    AIMS: To examine penile vibratory stimulation (PVS) in the treatment of post-prostatectomy urinary incontinence (UI). METHODS: Patients with post-prostatectomy UI were included in a 12-week trial. A 24-hr pad test and a 72-hr voiding diary were collected at baseline. Participants were randomized ...

  7. Procedures for evaluation of vibratory ground motions of soil deposits at nuclear power plant sites

    International Nuclear Information System (INIS)

    1975-06-01

    According to USNRC requirements set forth in Appendix A, 10 CFR, Part 100, vibratory ground motion criteria for a nuclear plant must be based on local soil conditions, as well as on the seismicity, geology, and tectonics of the region. This report describes how such criteria can be developed by applying the latest technology associated with analytical predictions of site-dependent ground motions and with the use of composite spectra obtained from the current library of strong motion records. Recommended procedures for defining vibratory ground motion criteria contain the following steps: (1) geologic and seismologic studies; (2) site soils investigations; (3) site response sensitivity studies; (4) evaluation of local site response characteristics; (5) selection of site-matched records; and (6) appraisal and selection of seismic input criteria. An in-depth discussion of the engineering characteristics of earthquake ground motions including parameters used to characterize earthquakes and strong motion records, geologic factors that influence ground shaking, the current strong motion data base, and case histories of the effects of past earthquake events is presented. Next, geotechnical investigations of the seismologic, geologic, and site soil conditions required to develop vibratory motion criteria are briefly summarized. The current technology for establishing vibratory ground motion criteria at nuclear plant sites, including site-independent and site-dependent procedures that use data from strong motion records and from soil response analyses is described. (auth)

  8. On dynamics and control of vibratory gyroscopes with special spherical symmetry

    CSIR Research Space (South Africa)

    Shatalov, M

    2006-05-01

    Full Text Available It was shown in 1985 by Acad. V. Zhuravlev that the angular rate of a pure vibrating mode excited in a vibratory gyroscope with spherical symmetry is proportional to an inertial angular rate of the gyroscope. The effect is three dimensional...

  9. Can vibratory feedback be used to improve postural stability in persons with transtibial limb loss?

    Science.gov (United States)

    Rusaw, David; Hagberg, Kerstin; Nolan, Lee; Ramstrand, Nerrolyn

    2012-01-01

    The use of vibration as a feedback modality to convey motion of the body has been shown to improve measures of postural stability in some groups of patients. Because individuals using transtibial prostheses lack sensation distal to the amputation, vibratory feedback could possibly be used to improve their postural stability. The current investigation provided transtibial prosthesis users (n = 24, mean age 48 yr) with vibratory feedback proportional to the signal received from force transducers located under the prosthetic foot. Postural stability was evaluated by measuring center of pressure (CoP) movement, limits of stability, and rhythmic weight shift while participants stood on a force platform capable of rotations in the pitch plane (toes up/toes down). The results showed that the vibratory feedback increased the mediolateral displacement amplitude of CoP in standing balance and reduced the response time to rapid voluntary movements of the center of gravity. The results suggest that the use of vibratory feedback in an experimental setting leads to improvements in fast open-loop mechanisms of postural control in transtibial prosthesis users.

  10. Automated Measurement of Vocal Fold Vibratory Asymmetry from High-Speed Videoendoscopy Recordings

    Science.gov (United States)

    Mehta, Daryush D.; Deliyski, Dimitar D.; Quatieri, Thomas F.; Hillman, Robert E.

    2011-01-01

    Purpose: In prior work, a manually derived measure of vocal fold vibratory phase asymmetry correlated to varying degrees with visual judgments made from laryngeal high-speed videoendoscopy (HSV) recordings. This investigation extended this work by establishing an automated HSV-based framework to quantify 3 categories of vocal fold vibratory…

  11. Wave radiation from vibratory and impact pile driving in a layered acousto-elastic medium

    NARCIS (Netherlands)

    Tsouvalas, A.; Metrikine, A.

    2014-01-01

    A steel monopile is the most common foundation type of a wind turbine installed offshore and is driven into place with the help of vibratory or impact hammers. Underwater noise generated during the installation of steel monopiles has recently received considerable attention from international

  12. Deceptive vibratory communication: pupae of a beetle exploit the freeze response of larvae to protect themselves.

    Science.gov (United States)

    Kojima, Wataru; Ishikawa, Yukio; Takanashi, Takuma

    2012-10-23

    It is argued that animal signals may have evolved so as to manipulate the response of receivers in a way that increases the fitness of the signallers. In deceptive communication, receivers incur costs by responding to false signals. Recently, we reported that pupae of the soil-inhabiting Japanese rhinoceros beetle Trypoxylus dichotoma produce vibratory signals to deter burrowing larvae, thereby protecting themselves. In the present study, monitoring of vibrations associated with larval movement revealed that T. dichotoma larvae remained motionless for ca 10 min when pupal vibratory signals were played back transiently (freeze response). Furthermore, pupal signals of T. dichotoma elicited a freeze response in three other scarabaeid species, whose pupae do not produce vibratory signals. This indicates that the freeze response to certain types of vibration evolved before the divergence of these species and has been evolutionarily conserved, presumably because of the fitness advantage in avoiding predators. Pupae of T. dichotoma have probably exploited pre-existing anti-predator responses of conspecific larvae to protect themselves by emitting deceptive vibratory signals.

  13. Control of Vibratory Energy Harvesters in the Presence of Nonlinearities and Power-Flow Constraints

    Science.gov (United States)

    Cassidy, Ian L.

    Over the past decade, a significant amount of research activity has been devoted to developing electromechanical systems that can convert ambient mechanical vibrations into usable electric power. Such systems, referred to as vibratory energy harvesters, have a number of useful of applications, ranging in scale from self-powered wireless sensors for structural health monitoring in bridges and buildings to energy harvesting from ocean waves. One of the most challenging aspects of this technology concerns the efficient extraction and transmission of power from transducer to storage. Maximizing the rate of power extraction from vibratory energy harvesters is further complicated by the stochastic nature of the disturbance. The primary purpose of this dissertation is to develop feedback control algorithms which optimize the average power generated from stochastically-excited vibratory energy harvesters. This dissertation will illustrate the performance of various controllers using two vibratory energy harvesting systems: an electromagnetic transducer embedded within a flexible structure, and a piezoelectric bimorph cantilever beam. Compared with piezoelectric systems, large-scale electromagnetic systems have received much less attention in the literature despite their ability to generate power at the watt--kilowatt scale. Motivated by this observation, the first part of this dissertation focuses on developing an experimentally validated predictive model of an actively controlled electromagnetic transducer. Following this experimental analysis, linear-quadratic-Gaussian control theory is used to compute unconstrained state feedback controllers for two ideal vibratory energy harvesting systems. This theory is then augmented to account for competing objectives, nonlinearities in the harvester dynamics, and non-quadratic transmission loss models in the electronics. In many vibratory energy harvesting applications, employing a bi-directional power electronic drive to actively

  14. European single-hull regulation in force

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, Michael

    2004-07-01

    The European Union (EU)has decided that from 21 October 2003 no single-hull tanker carrying heavy grades of oil will be permitted to enter or leave ports or offshore installations or anchor in areas under the jurisdiction of the EU member states. Some of the provisions of the EU regulation will not be in force until 2010. The article looks back on what has led up to to the current regulations, beginning with the Titanic disaster of 1914.

  15. The Causes of Boat Hull Blisters

    Science.gov (United States)

    1987-05-01

    blistering. The report is divided into the following sections: Introduction; How Blisters Form; the Hull Material; Manufacturing Processes; Water Diffusion...Term Effects of Water Up-Takeo " The much more detailed and highly technical report of thia-Vsrk is entitled "The Causes of Blistering in Boat Building...Chemical Engineering, ably assisted by several graduate students, and was completed in the fall of 1986. The report itself, d List-ribution/_ Availabilit

  16. 46 CFR 32.75-5 - Hull requirements; general-TB/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Hull requirements; general-TB/ALL. 32.75-5 Section 32.75..., AND HULL REQUIREMENTS Hull Requirements for Wood Hull Tank Vessels Constructed Prior to November 10, 1936 § 32.75-5 Hull requirements; general—TB/ALL. The scantlings, material, and workmanship, and the...

  17. 46 CFR 32.70-5 - Hull requirements; general-TB/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Hull requirements; general-TB/ALL. 32.70-5 Section 32.70..., AND HULL REQUIREMENTS Hull Requirements for Steel Hull Tank Vessels Constructed Prior to November 10, 1936 § 32.70-5 Hull requirements; general—TB/ALL. The scantlings, material, and workmanship, the...

  18. Novosadski golozrni, a spring oat variety

    Directory of Open Access Journals (Sweden)

    Pržulj Novo

    2001-01-01

    Full Text Available The naked oat variety Novosadski golozrni was developed from a cross between the variety Adam and a spring-type naked oat line from Canada. The variety is early, medium tall, with excellent resistance to lodging. The yield of Novosadski golozrni is 30-40% lower than that of the hulled standard and it is to the largest measure dependent on the interaction variety x year x location. The variety has high contents of proteins and fats (19.2% DM and 6.2% DM, respectively and a low cellulose content (2.8% DM. .

  19. Wave induced extreme hull girder loads on containerships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Pedersen, Preben Terndrup; Shi, Bill

    2009-01-01

    This paper provides simple but rational procedures for prediction of extreme wave – induced sectional hull girder forces with reasonable engineering accuracy. The procedures take into account main ship hull characteristics such as: length, breadth, draught, block coefficient, bow flare coefficient......, forward speed and hull flexibility. The vertical hull girder loads are evaluated for specific operational profiles. Firstly a quadratic strip theory is presented which can give separate predictions for the hogging and sagging bending moments and shear forces and for hull girder loads. Then this procedure...... is based on rational methods it can be applied for novel single hull ship types not presently covered by the rules of the classification societies or to account for specific operational profiles....

  20. Evaluation of Composite-Hull Ships Operating in Arctic Ice

    Science.gov (United States)

    2016-06-01

    COMPOSITE- HULL SHIPS OPERATING IN ARCTIC ICE by Ryan M. Tran June 2016 Thesis Advisor: Young W. Kwon Co-Advisor: Jarema M. Didoszak THIS...Master’s thesis 4. TITLE AND SUBTITLE EVALUATION OF COMPOSITE- HULL SHIPS OPERATING IN ARCTIC ICE 5. FUNDING NUMBERS 6. AUTHOR Ryan M. Tran 7...melting ice caps. Extensive research is thus being conducted to determine the interaction between ice and steel- hulls in anticipation of opening sea

  1. Topology Model of the Flow around a Submarine Hull Form

    Science.gov (United States)

    2015-12-01

    UNCLASSIFIED Topology Model of the Flow around a Submarine Hull Form S.-K. Lee Maritime Division Defence Science and Technology Group DST-Group–TR...3177 ABSTRACT A topology model constructed from surface-streamer visualisation describes the flow around a generic conventional submarine hull form at...pure yaw angles of 0 ◦, 10 ◦ and 18 ◦. The model is used to develop equations for sway-force and yaw-moment coefficients which relate to the hull - form

  2. Effects of Geometry on the Steady Performance of Planing Hulls

    DEFF Research Database (Denmark)

    Wagner, M. K.; Andersen, Poul

    2003-01-01

    A vortex-lattice method is applied to planing hull forms. The geometry of the jet surfaces next to the wetted hull is estimated on the basis of the hull geometry while its sidewise extent has been found numerically applying a non-linear free-surface pressure condition in the jet region. The method...... is applied to practical hull forms with chines spray rails and with varying deadrise over the length of the boat. The deadrise variation has a large influence on lift and drag. For a design situation, where the total lift and centre of effort is given, the influence on the total drag is less due to change...

  3. Rice Hulls as a Renewable Complex Material Resource

    Directory of Open Access Journals (Sweden)

    Irina Glushankova

    2018-05-01

    Full Text Available As a result of rice grain processing, a big amount of waste (up to 20% is produced. It is mainly rice hulls. The main components of rice hulls are cellulose, lignin and mineral ash. The mineral ash quantity in rice hulls varies from 15 up to 20%, by weight of the rice hulls. The mineral ash consists of amorphous silica (opal-type. Due to the high content of silica in rice hulls, the material burns with difficulty under natural conditions, and it is biodegradably destroyed only with difficulty, when composted. Utilization of rice hulls then becomes an ecological problem due to huge rice production and its continuous growth. At the same time, the annual quantity of silica content in rice hulls is comparable with the quantity of amorphous silica produced as a mineral resource. The issue of manufacturing cellular glass silica construction materials from rice hulls as a renewable resource is discussed in this paper. The utilization technology is based on an amorphous silicon oxide with the use of energy from the combustion of the organic component of rice hulls.

  4. Estimation of gamma dose rate from hulls and shield design for the hull transport cask of Fuel Reprocessing Plant (FRP)

    International Nuclear Information System (INIS)

    Chandrasekaran, S.; Rajagopal, V.; Jose, M.T.; Venkatraman, B.

    2012-01-01

    In Fuel Reprocessing Plant (FRP), un-dissolved clad of fuel pins known as hulls are the major sources of high level solid waste. Safe handling, transport and disposal require the estimation of radioactivity as a consequent of gamma dose rate from hulls in fast reactor fuel reprocessing plant in comparison with thermal reactor fuel. Due to long irradiation time and low cooling of spent fuel, the evolution of activation products 51 Cr, 58 Co, 54 Mn and 59 Fe present as impurities in the fuel clad are the major sources of gamma radiation. Gamma dose rate from hull container with hulls from Fuel Sub Assembly (FSA) and Radial Sub Assembly (RSA) of Fuel Reprocessing Plant (FRP) was estimated in order to design the hull transport cask. Shielding computations were done using point kernel code, IGSHIELD. This paper describes the details of source terms, estimation of dose rate and shielding design of hull transport cask in detail. (author)

  5. Technical note: In situ ruminal starch disappearance kinetics of hull-less barley, hulled barley, and corn grains.

    Science.gov (United States)

    Ferreira, G; Yang, Y; Teets, C L; Brooks, W S; Griffey, C A

    2018-07-01

    The objective of this study was to compare ruminal starch disappearance rates of hull-less barley, hulled barley, and corn grains. Five different genotypes were used for each of the 2 barley types. In addition, each of these genotypes was grown in 2 different locations and years, resulting 10 independent barley samples for each of the 2 barley grain types. Five different genotypes of corn grain were obtained from a commercial seed company. After being ground to pass through a 4-mm screen of a cutter mill, 3.6 g of each grain was placed into a porous bag, which was then incubated in the rumen of 2 ruminally cannulated cows for 0, 4, 8, 12, 24, and 48 h. Corn grains had greater instant ruminal starch disappearances than barley grains (22.4 and 8.2%, respectively). Instant ruminal starch disappearances did not differ between hulled and hull-less barley grains. Ruminal starch fractional disappearance rates were greatest for hulled barley grains, moderate for hull-less barley grains, and lowest for corn grains (15.3, 13.9, and 7.1%/h, respectively). Ruminal starch half-life was shortest for hulled and hull-less barley grains (4.4 h) and longest for corn grains (6.6 h). Ruminal starch half-life did not differ between hulled barley and hull-less barley grains. In conclusion, using a holistic experimental design and statistical analysis, this study showed that starch from hull-less barley grains has a ruminal half-life similar to that of hulled barley grains and shorter than that of corn grains. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  6. In-Water Hull Cleaning & Filtration System

    Science.gov (United States)

    George, Dan

    2015-04-01

    Dan George R & D Mining Technology LinkedIn GRD Franmarine have received the following prestigious awards in 2014 for their research & development of an in-water hull cleaning and filtration system "The Envirocart: Golden Gecko Award for Environmental Excellence; WA Innovator of the Year - Growth Sector; Department of Fisheries - Excellence in Marine Biosecurity Award - Innovation Category; Lloyd's List Asia Awards - Environmental Award; The Australian Innovation Challenge - Environment, Agriculture and Food Category; and Australian Shipping and Maritime Industry Award - Environmental Transport Award. The Envirocart developed and patented by GRD Franmarine is a revolutionary new fully enclosed capture and containment in-water hull cleaning technology. The Envirocart enables soft Silicon based antifouling paints and coatings containing pesticides such as Copper Oxide to be cleaned in situ using a contactless cleaning method. This fully containerised system is now capable of being deployed to remote locations or directly onto a Dive Support Vessel and is rated to offshore specifications. This is the only known method of in-water hull cleaning that complies with the Department of Agriculture Fisheries and Forestry (DAFF) and Department of Fisheries WA (DoF) Guidelines. The primary underwater cleaning tool is a hydraulically powered hull cleaning unit fitted with rotating discs. The discs can be fitted with conventional brushes for glass or epoxy based coatings or a revolutionary new patented blade system which can remove marine biofouling without damaging the antifouling paint (silicone and copper oxide). Additionally there are a patented range of fully enclosed hand cleaning tools for difficult to access niche areas such as anodes and sea chests, providing an innovative total solution that enables in-water cleaning to be conducted in a manner that causes no biological risk to the environment. In full containment mode or when AIS are present, material is pumped

  7. A Fiber-Optic Tether for the Hull Search UUV System Documentation

    National Research Council Canada - National Science Library

    Buescher, J. G

    2006-01-01

    ...) conducting ship hull inspection missions, defines the required specifications that will allow the integration and installation of a FO tether system on UUVs with ship hull inspection capability...

  8. Vibratory-compacted (vipac/sphere-pac) nuclear fuels - a comparison with pelletized nuclear fuels

    Energy Technology Data Exchange (ETDEWEB)

    Chidester, K.; Rubin, J. [Los Alamos National Lab., NM (United States); Thompson, M

    2001-07-01

    In order to achieve the packing densities required for nuclear fuel stability, economy and performance, the fuel material must be densified. This has traditionally been performed by high-temperature sintering. (At one time, fuel densification was investigated using cold/hot swaging. However, this fabrication method has become uncommon.) Alternatively, fuel can be densified by vibratory compaction (VIPAC). During the late 1950's and into the 1970's, in the U.S., vibratory compaction fuel was fabricated and test irradiated to evaluate its applicability compared to the more traditional pelletized fuel for nuclear reactors. These activities were primarily focused on light water reactors (LWR) but some work was performed for fast reactors. This paper attempts to summarize these evaluations and proposes to reconsider VIPAC fuel for future use. (author)

  9. IMPACT OF VIBRATORY AND ROTATIONAL SHOT PEENING ONTO SELECTED PROPERTIES OF TITANIUM ALLOY SURFACE LAYER

    Directory of Open Access Journals (Sweden)

    Kazimierz Zaleski

    2014-06-01

    Full Text Available This study presents the results of tests on impact of vibratory and rotational shot peening of the Ti6A12Mo2Cr titanium alloy onto the processed object surface roughness and surface layer microhardness. The external surfaces of ring-shaped samples were shot peened. The preceding process consisted of turning with a cubic boron nitride blade knife. Steel beads, having a diameter of 6 mm, were used as a processing medium. The variable parameters of shot peening were vibrator amplitude and shot peening time. The range of recommended technological parameters for vibratory and rotational shot peening was determined. As a result of shot peening, the surface roughness could be reduced by approximately 4 times and the surface layer could be hardened to the depth of approximately 0.4 mm.

  10. Vibratory-compacted (vipac/sphere-pac) nuclear fuels - a comparison with pelletized nuclear fuels

    International Nuclear Information System (INIS)

    Chidester, K.; Rubin, J.; Thompson, M.

    2001-01-01

    In order to achieve the packing densities required for nuclear fuel stability, economy and performance, the fuel material must be densified. This has traditionally been performed by high-temperature sintering. (At one time, fuel densification was investigated using cold/hot swaging. However, this fabrication method has become uncommon.) Alternatively, fuel can be densified by vibratory compaction (VIPAC). During the late 1950's and into the 1970's, in the U.S., vibratory compaction fuel was fabricated and test irradiated to evaluate its applicability compared to the more traditional pelletized fuel for nuclear reactors. These activities were primarily focused on light water reactors (LWR) but some work was performed for fast reactors. This paper attempts to summarize these evaluations and proposes to reconsider VIPAC fuel for future use. (author)

  11. Mechanical Assessment of the Drip Shield Subject to Vibratory Motion and Dynamic and Static Rock Loading

    International Nuclear Information System (INIS)

    R.C. Quittmeyer

    2005-01-01

    The purpose of the drip shield (DS) is to divert water that may seep into emplacement drifts from contacting the waste packages, and to protect the waste packages from impact or static loading from rockfall. The objective of this document is to summarize, into one location, the results of a series of supporting engineering calculations that were developed to study the effect of static and dynamic loads on the mechanical performance of the DS. The potential DS loads are a result of: (1) Potential earthquake vibratory ground motion, and resulting interaction of the DS, waste package and pallet, and drift invert; (2) Dynamic impacts of rockfall resulting from emplacement drift damage as a result of earthquake vibratory motion; and (3) Static load of the caved rock rubble that may come to rest on the DS as a result of vibratory motion or from time-dependent yielding of the rock mass surrounding the emplacement drift. The potential mechanical failure mechanisms that may result from these loads include: (1) Overturning and/or separation of the interlocking DS segments; (2) Loss of structural integrity and stability of the DS, including excessive deformation or buckling; and (3) Localized damage to the top and side-wall plates of the DS. The scope of this document is limited to summarizing results presented in the supporting calculations in the areas of analysis of the potential for DS collapse, and determination of the damaged surface area of the DS plates. New calculations are presented to determine whether or not separation of DSs occur under vibratory motion

  12. Approximate convex hull of affine iterated function system attractors

    International Nuclear Information System (INIS)

    Mishkinis, Anton; Gentil, Christian; Lanquetin, Sandrine; Sokolov, Dmitry

    2012-01-01

    Highlights: ► We present an iterative algorithm to approximate affine IFS attractor convex hull. ► Elimination of the interior points significantly reduces the complexity. ► To optimize calculations, we merge the convex hull images at each iteration. ► Approximation by ellipses increases speed of convergence to the exact convex hull. ► We present a method of the output convex hull simplification. - Abstract: In this paper, we present an algorithm to construct an approximate convex hull of the attractors of an affine iterated function system (IFS). We construct a sequence of convex hull approximations for any required precision using the self-similarity property of the attractor in order to optimize calculations. Due to the affine properties of IFS transformations, the number of points considered in the construction is reduced. The time complexity of our algorithm is a linear function of the number of iterations and the number of points in the output approximate convex hull. The number of iterations and the execution time increases logarithmically with increasing accuracy. In addition, we introduce a method to simplify the approximate convex hull without loss of accuracy.

  13. 46 CFR 45.143 - Hull openings above freeboard deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Hull openings above freeboard deck. 45.143 Section 45.143 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.143 Hull openings above freeboard deck. Closures for openings above...

  14. 46 CFR 78.50-5 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Hull markings. 78.50-5 Section 78.50-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Markings on Vessels § 78.50-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this chapter. [CGD 72...

  15. 46 CFR 196.40-5 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull markings. 196.40-5 Section 196.40-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS OPERATIONS Markings on Vessels § 196.40-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this chapter...

  16. Iron-59 absorption from soy hulls: intrinsic vs extrinsic labeling

    International Nuclear Information System (INIS)

    Lykken, G.I.; Mahalko, J.R.; Nielsen, E.J.; Dintzis, F.R.

    1986-01-01

    As part of an evaluation of the validity of the extrinsic labeling technique for measuring iron absorption, absorption from soy hulls extrinsically labeled ( 59 Fe added to bread dough) was compared with that from soy hulls intrinsically labeled ( 59 Fe incorporated into the soy plant during growth). Century soybeans were grown in a greenhouse. After pods had formed and were filling, each plant was stem injected twice, at 3 day intervals, with 22 μCi 59 Fe as FeCl 2 in 25 μl of 0.5 M HCl solution. After the plants had senesced, the soybeans were harvested, dried, shelled and the hulls removed. Standard meals containing 3.5 mg Fe/meal and up to 0.06 μCi 59 Fe in a soy hull bun were fed on 2 consecutive days to free-living volunteers in a crossover design. Absorption of 59 Fe was greater from intrinsically labeled soy hulls than from extrinsically labeled soy hulls, 20 +/- 20% vs 15 +/- 11% (n=14, p > 0.05 by paired t-test). Apparent absorption ranged from 1.3% to 77% from intrinsically labeled soy hulls and .5% to 29% from extrinsically labeled soy hulls with the highest absorption occurring in persons with low serum ferritin (S.F. < 8 ng/ml). These findings provide additional evidence that the extrinsic labeling method is a valid measure of iron bioavailability to humans

  17. 46 CFR 97.40-5 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull markings. 97.40-5 Section 97.40-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Markings on Vessels § 97.40-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this...

  18. 46 CFR 174.225 - Hull penetrations and shell connections.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull penetrations and shell connections. 174.225 Section 174.225 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY... § 174.225 Hull penetrations and shell connections. Each overboard discharge and shell connection except...

  19. 76 FR 7757 - Hull Identification Numbers for Recreational Vessels

    Science.gov (United States)

    2011-02-11

    ... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 181 [Docket No. USCG-2007-29236] Hull Identification Numbers for Recreational Vessels AGENCY: Coast Guard, DHS. ACTION: Follow-up to request for... expanded hull identification number (HIN). The Coast Guard's decision-making process included consideration...

  20. 77 FR 59575 - Hull Identification Numbers for Recreational Vessels

    Science.gov (United States)

    2012-09-28

    ... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 181 [Docket No. USCG-2012-0843] Hull Identification Numbers for Recreational Vessels AGENCY: Coast Guard, DHS. ACTION: Request for public comments... requirement to indicate a boat's model year as part of the 12-character Hull Identification Number (HIN...

  1. Determination of digestibility of almond hull in sheep | Yalchi ...

    African Journals Online (AJOL)

    Chemical compositions of almond hull and alfalfa hay were determined. The crude protein (CP), neutral detergent fiber (NDF) and acid detergent fiber (ADF) of almond hull were lower than those of alfalfa hay but the non fibrous carbohydrate (NFC) was more than that of alfalfa hay (3.5 times) (P < 0.01). The dry matter ...

  2. Feasibility of Using Rice Hulls as Bedding for Laboratory Mice.

    Science.gov (United States)

    Carbone, Elizabeth T; Kass, Philip H; Evans, Kristin D

    2016-01-01

    Factors that are considered when selecting laboratory mouse bedding include animal health and comfort, cost, effects on personnel, and bioactive properties. Corncob is economical and facilitates low intracage ammonia but has undesirable influences on some endocrine studies. Rice hulls are an economical material that has not been well characterized as a bedding substrate. In this pilot study, we compared various aspects of bedding performance of rice hulls and other materials. On a per-volume basis, rice hulls were less absorbent than was corncob bedding. Rice hulls had higher odds than did corncob or reclaimed wood pulp of having moisture present at the bedding surface. The results of the absorbency tests coupled with the results of preliminary monitoring of intracage ammonia raised concern about the ability of rice hulls to control ammonia levels sufficiently in cages with high occupancy. However, ammonia was negligible when cages contained 5 young adult female mice. The relative expression of 3 cytochrome p450 genes was compared among mice housed on rice hulls, corncob, reclaimed wood pulp, or pine shavings. The expression of Cyp1a2 was 1.7 times higher in the livers of mice housed on rice hulls than on pine shavings, but other differences were not statistically significant. This study provides information on the merits of rice hulls as laboratory mouse bedding. Their relatively poor moisture control is a major disadvantage that might preclude their widespread use.

  3. Teleoperation of steerable flexible needles by combining kinesthetic and vibratory feedback.

    Science.gov (United States)

    Pacchierotti, Claudio; Abayazid, Momen; Misra, Sarthak; Prattichizzo, Domenico

    2014-01-01

    Needle insertion in soft-tissue is a minimally invasive surgical procedure that demands high accuracy. In this respect, robotic systems with autonomous control algorithms have been exploited as the main tool to achieve high accuracy and reliability. However, for reasons of safety and responsibility, autonomous robotic control is often not desirable. Therefore, it is necessary to focus also on techniques enabling clinicians to directly control the motion of the surgical tools. In this work, we address that challenge and present a novel teleoperated robotic system able to steer flexible needles. The proposed system tracks the position of the needle using an ultrasound imaging system and computes needle's ideal position and orientation to reach a given target. The master haptic interface then provides the clinician with mixed kinesthetic-vibratory navigation cues to guide the needle toward the computed ideal position and orientation. Twenty participants carried out an experiment of teleoperated needle insertion into a soft-tissue phantom, considering four different experimental conditions. Participants were provided with either mixed kinesthetic-vibratory feedback or mixed kinesthetic-visual feedback. Moreover, we considered two different ways of computing ideal position and orientation of the needle: with or without set-points. Vibratory feedback was found more effective than visual feedback in conveying navigation cues, with a mean targeting error of 0.72 mm when using set-points, and of 1.10 mm without set-points.

  4. Effects of vibratory stimulation-induced kinesthetic illusions on the neural activities of patients with stroke.

    Science.gov (United States)

    Kodama, Takayuki; Nakano, Hideki; Ohsugi, Hironori; Murata, Shin

    2016-01-01

    [Purpose] This study evaluated the influence of vibratory stimulation-induced kinesthetic illusion on brain function after stroke. [Subjects] Twelve healthy individuals and 13 stroke patients without motor or sensory loss participated. [Methods] Electroencephalograms were taken at rest and during vibratory stimulation. As a neurophysiological index of brain function, we measured the μ-rhythm, which is present mainly in the kinesthetic cortex and is attenuated by movement or motor imagery and compared the data using source localization analyses in the Standardized Low Resolution Brain Electromagnetic Tomography (sLORETA) program. [Results] At rest, μ-rhythms appeared in the sensorimotor and supplementary motor cortices in both healthy controls and stroke patients. Under vibratory stimulation, no μ-rhythm appeared in the sensorimotor cortex of either group. Moreover, in the supplementary motor area, which stores the motor imagery required for kinesthetic illusions, the μ-rhythms of patients were significantly stronger than those of the controls, although the μ-rhythms of both groups were reduced. Thus, differences in neural activity in the supplementary motor area were apparent between the subject groups. [Conclusion] Kinesthetic illusions do occur in patients with motor deficits due to stroke. The neural basis of the supplementary motor area in stroke patients may be functionally different from that found in healthy controls.

  5. Gearbox fault diagnosis based on deep random forest fusion of acoustic and vibratory signals

    Science.gov (United States)

    Li, Chuan; Sanchez, René-Vinicio; Zurita, Grover; Cerrada, Mariela; Cabrera, Diego; Vásquez, Rafael E.

    2016-08-01

    Fault diagnosis is an effective tool to guarantee safe operations in gearboxes. Acoustic and vibratory measurements in such mechanical devices are all sensitive to the existence of faults. This work addresses the use of a deep random forest fusion (DRFF) technique to improve fault diagnosis performance for gearboxes by using measurements of an acoustic emission (AE) sensor and an accelerometer that are used for monitoring the gearbox condition simultaneously. The statistical parameters of the wavelet packet transform (WPT) are first produced from the AE signal and the vibratory signal, respectively. Two deep Boltzmann machines (DBMs) are then developed for deep representations of the WPT statistical parameters. A random forest is finally suggested to fuse the outputs of the two DBMs as the integrated DRFF model. The proposed DRFF technique is evaluated using gearbox fault diagnosis experiments under different operational conditions, and achieves 97.68% of the classification rate for 11 different condition patterns. Compared to other peer algorithms, the addressed method exhibits the best performance. The results indicate that the deep learning fusion of acoustic and vibratory signals may improve fault diagnosis capabilities for gearboxes.

  6. Morphologically intelligent underactuated robot for underwater hull cleaning

    DEFF Research Database (Denmark)

    Souto, Daniel; Faina, Andres; López-Peña, Fernando

    2015-01-01

    In this paper we discuss a new type of robot for underwater hull cleaning on ships with non-magnetic hulls. This robot is based on the concept that cleaning hulls regularly, without waiting to take them out of the water, will improve the efficiency of the ships and will permit a reduction...... in the use of the chemicals that are usually employed to prevent the growth of marine life on the hull and which are generally harmful to the environment. The robot described in this paper is an underactuated morphologically adapted robot that through an appropriate morphology and making use of the forces...... and constraints of the environment solves the most difficult problems that arise when moving along hulls. Some of these are changing planes, negotiating appendices, avoiding portholes, passing corners, and other elements. This greatly simplifies the control mechanisms that are required for its operation making...

  7. Experimental Evaluation of the Hydrodynamic Response of Crew Boat Hulls

    DEFF Research Database (Denmark)

    Pecher, Arthur; Kofoed, Jens Peter

    This report presents the results of an experimental study on 3 different hulls of crew boats intended for service to offshore wind turbines. Their hydrodynamic behaviour has been tested in various sea states representing general wave conditions that could be expected at offshore wind farms. Two...... main setups were used during the tests, corresponding to the hulls being connected to an offshore windmill and being free floating. The following aspects were the main subjects of investigation: • The Response Amplitude Operators of the hulls in two different configurations and with waves coming from 3...... different directions. • The connection forces between the hulls and the wind turbine pile. • The natural frequency of oscillation. For the study, realistic scale models of the hulls of the crew boats were supplied by the client, Hauschildt Marine. The laboratory tests were performed by Arthur Pecher under...

  8. Characterisation of the activities associated with fast reactor cladding hulls

    International Nuclear Information System (INIS)

    Biddle, P.; Rees, J.H.

    1987-01-01

    Four batches of hulls from the reprocessing of fuel from the Prototype Fast Reactor at Dounreay have been examined visually and photographically. The appearance of the hulls (shiny or black) depended on the original location in the fuel pin. The total fissile activities measured corresponded to less than 0.1% or the original fuel. The α-emitter, fission product and activation product activities have been determined from dissolution studies. Profile diagrams have been constructed for the distribution of the principal activities along lengths of seventeen hulls. The evidence obtained suggested that much of the activity on the hulls arose through deposition from the dissolver liquors. The deposits included insoluble particulate material which was thought to be responsible for the wide variations in activity across short lengths of some of the hulls. (orig.)

  9. On the wave induced responses for a high-speed hydrofoil catamaran. Part 1. Cabin connected to hull by spring and its riding comfort in waves; Suichuyokutsuki kosoku sodotei no harochu oto ni tsuite. 1. Dokuritsu kozogata cabin to harochu norigokochi

    Energy Technology Data Exchange (ETDEWEB)

    Saito, K; Nobukawa, H; Honda, Y [Hiroshima University, Hiroshima (Japan)

    1996-04-10

    Riding comfort in a cabin of a high-speed hydrofoil catamaran was evaluated by comparing with that in ordinary boats as to acceleration in the vertical direction as one of the responses of the catamaran in waves. First, an equation of motion in waves was introduced, and considerations were given while comparing the result of calculations in regular waves with that of model experiments. Comparison and verification were also performed on response characteristics in irregular waves. A new-type boat, whose cabin is supported with four springs, and provided with hydrofoils in front and rear thereof, was verified to have much less motions of the catamaran bodies and the cabin than in the ordinary boats both in regular and irregular waves. This result was proven by numerical calculations and model experiments. Hydrofoils affect largely the reduction in motions. The correlational data between the results of calculations and experiments are considered sufficient to provide design data, although there are still some points to be improved. These results revealed that the riding comfort of the new-type boat has been improved over that in the ordinary boats. 6 refs., 11 figs., 3 tabs.

  10. Identification of a novel SPLIT-HULL (SPH) gene associated with hull splitting in rice (Oryza sativa L.).

    Science.gov (United States)

    Lee, Gileung; Lee, Kang-Ie; Lee, Yunjoo; Kim, Backki; Lee, Dongryung; Seo, Jeonghwan; Jang, Su; Chin, Joong Hyoun; Koh, Hee-Jong

    2018-07-01

    The split-hull phenotype caused by reduced lemma width and low lignin content is under control of SPH encoding a type-2 13-lipoxygenase and contributes to high dehulling efficiency. Rice hulls consist of two bract-like structures, the lemma and palea. The hull is an important organ that helps to protect seeds from environmental stress, determines seed shape, and ensures grain filling. Achieving optimal hull size and morphology is beneficial for seed development. We characterized the split-hull (sph) mutant in rice, which exhibits hull splitting in the interlocking part between lemma and palea and/or the folded part of the lemma during the grain filling stage. Morphological and chemical analysis revealed that reduction in the width of the lemma and lignin content of the hull in the sph mutant might be the cause of hull splitting. Genetic analysis indicated that the mutant phenotype was controlled by a single recessive gene, sph (Os04g0447100), which encodes a type-2 13-lipoxygenase. SPH knockout and knockdown transgenic plants displayed the same split-hull phenotype as in the mutant. The sph mutant showed significantly higher linoleic and linolenic acid (substrates of lipoxygenase) contents in spikelets compared to the wild type. It is probably due to the genetic defect of SPH and subsequent decrease in lipoxygenase activity. In dehulling experiment, the sph mutant showed high dehulling efficiency even by a weak tearing force in a dehulling machine. Collectively, the results provide a basis for understanding of the functional role of lipoxygenase in structure and maintenance of hulls, and would facilitate breeding of easy-dehulling rice.

  11. Flaxseed hull: Chemical composition and antioxidant activity during development.

    Science.gov (United States)

    Herchi, Wahid; Al Hujaili, Abdullah D; Sakouhi, Faouzi; Sebei, Khaled; Trabelsi, Hajer; Kallel, Habib; Boukhchina, Sadok

    2014-01-01

    Changes in the chemical composition and antioxidant activity of flaxseed hull during maturation were investigated. P129 hull variety was studied at four maturation stages (St1, St2, St3, and St4). Significant variation in proximate composition and flaxseed hull oil characteristics were observed. A significant increase in the carbohydrates content of the hull was observed during development. The main methyl esters were linolenic acid (48.95 - 51.52 %), oleic acid (20.27-23.41%) and linoleic acid (15.62-17.70%). The highest polyunsaturated fatty acids (PUFA) were found to be 67.14 % at the first stage of maturity (St1). Flaxseed hull oil was of good quality, containing an abundance of omega-3 essential fatty acids. The iodine value increased, while the saponification value of oil decreased during seed development. The decrease in ascorbic acid content was steady. The maximum level of total phenolic acid content (128.3 mg/100 g oil) was reached at 7 DAF. The antioxidant activity of oilseed was assessed by means of 2, 2-diphenyl-1-picrylhydrazyl (DPPH) radical-scavenging assay. Radical scavenging activity for green hull was 52.74% and mature hull was 69.32%.

  12. 46 CFR 91.15-1 - Standards in inspection of hulls, boilers, and machinery.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery... hulls, boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels, the..., respecting material and inspection of hulls, boilers, and machinery, and the certificate of classification...

  13. 46 CFR 189.15-1 - Standards in inspection of hulls, boilers, and machinery.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery... inspection of hulls, boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels... chapter, respecting material and construction of hulls, boilers, and machinery, and certificate of...

  14. 14 CFR 23.533 - Hull and main float bottom pressures.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float bottom pressures. 23... Water Loads § 23.533 Hull and main float bottom pressures. (a) General. The hull and main float....00213; K2=hull station weighing factor, in accordance with figure 2 of appendix I of this part; VS1...

  15. 46 CFR 32.63-5 - Barge hull classifications-B/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Barge hull classifications-B/ALL. 32.63-5 Section 32.63..., AND HULL REQUIREMENTS Hull and Cargo Tank Requirements for Tank Barges Constructed or Converted On or After July 1, 1964, and Carrying Certain Dangerous Bulk Cargoes § 32.63-5 Barge hull classifications—B...

  16. 37 CFR 212.5 - Recordation of distinctive identification of vessel hull designer.

    Science.gov (United States)

    2010-07-01

    ... identification of vessel hull designer. 212.5 Section 212.5 Patents, Trademarks, and Copyrights COPYRIGHT OFFICE, LIBRARY OF CONGRESS COPYRIGHT OFFICE AND PROCEDURES PROTECTION OF VESSEL HULL DESIGNS § 212.5 Recordation of distinctive identification of vessel hull designer. (a) General. Any owner of a vessel hull may...

  17. 46 CFR 71.50-1 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 71.50-1... INSPECTION AND CERTIFICATION Drydocking § 71.50-1 Definitions relating to hull examinations. As used in this part— Adequate hull protection system means a method of protecting the vessel's hull from corrosion. It...

  18. 14 CFR 29.519 - Hull type rotorcraft: Water-based and amphibian.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull type rotorcraft: Water-based and... § 29.519 Hull type rotorcraft: Water-based and amphibian. (a) General. For hull type rotorcraft, the... along and among the hull and auxiliary floats, if used, in a rational and conservative manner, assuming...

  19. 46 CFR 115.630 - The Alternative Hull Examination (AHE) Program application.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false The Alternative Hull Examination (AHE) Program... PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.630 The Alternative Hull... hull examination date to the Officer in Charge, Marine Inspection (OCMI) who will oversee the survey...

  20. Preparation and characterization of rice hull silica products

    International Nuclear Information System (INIS)

    Quirit, Leni L.; Llaguno, Elma C.; Pagdanganan, Fernando C.; Hernandez, Karen N.

    2008-01-01

    Rice hull is an abundant agricultural waste material which could be a renewable energy source when combusted. The combustion residue (called rice hull ash or RHA) contains a significant amount (20% of the hull) of potentially high grade silica. Silica gels prepared from rice hull were found to have properties comparable to two commercial desiccant silica gels (Blue Merck and FNG-A) in terms of chemical and amorphous structure, surface area, desiccant characteristics, microstructure and heats of adsorption. These properties were determined from water vapor adsorption measurements, electron microscopy, and from infrared and x-ray diffraction spectra. The acid treated rice hull gels were found to have fewer elemental impurities detected by qualitative x-ray fluorescence, compared to the commercial gels. Thermogravimetric analysis (TGA) data showed that this technique can also be used to indirectly compare impurity levels in the samples, in terms of the amorphous to crystalline phase transition. Using an improved acid treatment method, a silica gel sample was prepared from rice hull and compared to three commercial chromatographic silica gels using quantitative elemental x-ray fluorescence analysis. Elemental levels in the rice hull gel were within the range of levels or close to the detection limits of corresponding elements in the chromatographic gels. Water vapor adsorption, x-ray diffraction, infrared spectroscopy and scanning electron microscopy showed that the rice hull gel was similar to the commercial chromatographic silica gel Davison 12. Zeolites are crystalline aluminosilicates used as molecular sieves for purification and catalytic purposes. Zeolites X and Y were synthesized from rice hull silica gel and aluminum hydroxide. For comparison, controls were synthesized from commercial silica gel. The samples and controls exhibited characteristics infrared peaks corresponding to the vibrations of the TO 4 (T=Si, Al) of the zeolite framework. The x

  1. The study on radioactivity reduction of spent PWR cladding hull

    International Nuclear Information System (INIS)

    Jung, I. H.; Kim, J. H.; Park, C. J.; Jung, Y. H.; Song, K. C.; Lee, J. W.; Park, J. J.; Yang, M. S.

    2003-01-01

    Hull arising from the spent PWR fuel elements is classified as a high-level radioactive waste. This report describes the radio-chemical characteristics of the hull-from PWR spent fuel of 32,000MWd/tU burn-up and 15 years cooling, discharged from Gori Unit I cycled 4-7-by examination and literature survey. On the basis of the results, a method of degradation to middle and low-level radioactive waste was proposed by dry process such as laser or plasma technique with removing the nuclides deposited on the surface of the hull

  2. Corn fiber hulls as a food additive or animal feed

    Science.gov (United States)

    Abbas, Charles; Beery, Kyle E.; Cecava, Michael J.; Doane, Perry H.

    2010-12-21

    The present invention provides a novel animal feed or food additive that may be made from thermochemically hydrolyzed, solvent-extracted corn fiber hulls. The animal feed or food additive may be made, for instance, by thermochemically treating corn fiber hulls to hydrolyze and solubilize the hemicellulose and starch present in the corn fiber hulls to oligosaccharides. The residue may be extracted with a solvent to separate the oil from the corn fiber, leaving a solid residue that may be prepared, for instance by aggolmerating, and sold as a food additive or an animal feed.

  3. [The impact of vibratory stimulation therapy on voice quality in hyperfunctional occupational dysphonia].

    Science.gov (United States)

    Kosztyła-Hojna, Bożena; Kuryliszyn-Moskal, Anna; Rogowski, Marek; Moskal, Diana; Dakowicz, Agnieszka; Falkowski, Dawid; Kasperuk, Joanna

    2012-01-01

    Hyperfunctional dysphonia is the most frequent type of occupational functional dysphonia. Pharmacotherapy, physiotherapy and psychotherapy are used in the treatment of occupational dysphonia. Vibratory massages of the regions of the larynx relax the external muscles of neck, which have an indirect impact on the tension of the vocal folds. The aim of the study is to assess the impact of vibratory stimulation therapy on voice quality in patients with hyperfunctional occupational dysphonia treated pharmacologically. Forty patients with hyperfunctional occupational dysphonia treated phoniatrically in the Phoniatric Outpatient Clinic were included in the study. Patients were divided into two groups. Group I consisted of 20 patients treated pharmacologically. In group II, including 20 patients, apart from pharmacotherapy the vibratory stimulation therapy by the device of VR type (CyberBioMed LLC) was used. In the analysis of voice quality the evaluation of the vocal folds vibration using videolaryngostroboscopy and acoustic assessment of voice were conducted. The perceptual assessment of voice, the visualization of the vocal folds vibration in stroboscopic examination of the larynx and the acoustic assessment of voice enable the appropriate diagnostics of the clinical type and voice quality in hyperfunctional dysphonia. The tension of superficial and deep muscles of neck has the impact on the phonatory function of the larynx. Pharmacological treatment improves the voice quality in hyperfunctional occupational dysphonia. Pharmacological treatment combines with the relaxation of muscles of neck using the device of VR type significantly improve voice quality in hyperfunctional occupational dysphonia. Copyright © 2012 Polish Otolaryngology Society. Published by Elsevier Urban & Partner Sp. z.o.o. All rights reserved.

  4. Research on Bell-Shaped Vibratory Angular Rate Gyro’s Character of Resonator

    Directory of Open Access Journals (Sweden)

    Hong Liu

    2013-04-01

    Full Text Available Bell-shaped vibratory angular rate gyro (abbreviated as BVG is a new type Coriolis vibratory gyro that was inspired by Chinese traditional clocks. The resonator fuses based on a variable thickness axisymmetric multicurved surface shell. Its characteristics can directly influence the performance of BVG. The BVG structure not only has capabilities of bearing high overload, high impact and, compared with the tuning fork, vibrating beam, shell and a comb structure, but also a higher frequency to overcome the influence of the disturbance of the exterior environment than the same sized hemispherical resonator gyroscope (HRG and the traditional cylinder vibratory gyroscope. It can be widely applied in high dynamic low precision angular rate measurement occasions. The main work is as follows: the issue mainly analyzes the structure and basic principle, and investigates the bell-shaped resonator’s mathematical model. The reasonable structural parameters are obtained from finite element analysis and an intelligent platform. Using the current solid vibration gyro theory analyzes the structural characteristics and principles of BVG. The bell-shaped resonator is simplified as a paraboloid of the revolution mechanical model, which has a fixed closed end and a free opened end. It obtains the natural frequency and vibration modes based on the theory of elasticity. The structural parameters are obtained from the orthogonal method by the research on the structural parameters of the resonator analysis. It obtains the modal analysis, stress analysis and impact analysis with the chosen parameters. Finally, using the turntable experiment verifies the gyro effect of the BVG.

  5. "Keisri hull" kui müstiline fantasy / Siimon Prii

    Index Scriptorium Estoniae

    Prii, Siimon

    2006-01-01

    30. sept. Ugalas esietendunud Jaan Krossi "Keisri hull" (autoridramatiseering), lavastajad Jaak Allik ja Peeter Tammearu. Kunstnik on Jaanus Laagriküll ja muusikaline kujundaja Peeter Konovalov. Peaosas Peeter Tammearu

  6. Safety Evaluation for Hull Waste Treatment Process in JNC

    International Nuclear Information System (INIS)

    Kojima, H.; Kurakata, K.

    2002-01-01

    Hull wastes and some scrapped equipment are typical radioactive wastes generated from reprocessing process in Tokai Reprocessing Plant (TRP). Because hulls are the wastes remained in the fuel shearing and dissolution, they contain high radioactivity. Japan Nuclear Cycle Development Institute (JNC) has started the project of Hull Waste Treatment Facility (HWTF) to treat these solid wastes using compaction and incineration methods since 1993. It is said that Zircaloy fines generated from compaction process might burn and explode intensely. Therefore explosive conditions of the fines generated in compaction process were measured. As these results, it was concluded that the fines generated from the compaction process were not hazardous material. This paper describes the outline of the treatment process of hulls and results of safety evaluation

  7. Fluid-Structure Interaction Effects Resulting from Hull Appendage Coupling

    National Research Council Canada - National Science Library

    Avcu, Mehmet

    2005-01-01

    In previous work conducted in the modeling and simulation of ships subjected to underwater explosions, there has been some debate over the influence that hull appendages have upon the dynamic response...

  8. On Rational Design of Double Hull Tanker Structures against Collision

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Chung, Jang Young; Choe, Ich Hung

    1999-01-01

    This paper is a summary of recent research and development in areas related to the design technology for double hull tanker structures against low energy collision, jointly undertaken by the Hyundai Heavy Industries, the American Bureau of Shipping, the Technical University of Denmark and the Pusan...... in the present study were (i) developing a framework for the collision design procedure for double hull tanker structures, (ii) experimental investigation of the structural crashworthiness of the collided vessels in collision or stranding, using double skinned structural models, (iii) validation of the special...... investigation of the energy absorption capability characteristics of a collided double hull VLCC side structure in collision, and (vi) development of a new modified Minorsky method for double hull tanker side structures. The tools developed and the results and insights obtained by the present study should...

  9. Hull-Propeller Interaction and Its Effect on Propeller Cavitation

    DEFF Research Database (Denmark)

    Regener, Pelle Bo

    In order to predict the required propulsion power for a ship reliably and accurately, it is not sufficient to only evaluate the resistance of the hull and the propeller performance in open water alone. Interaction effects between hull and propeller can even be a decisive factor in ship powering...... prediction and design optimization. The hull-propeller interaction coefficients of effective wake fraction, thrust deduction factor, and relative rotative efficiency are traditionally determined by model tests. Self-propulsion model tests consistently show an increase in effective wake fractions when using...... velocities. This offers an opportunity for additional insight into hull-propeller interaction and the propeller’s actual operating condition behind the ship, as the actual (effective) inflow is computed. Self-propulsion simulations at model and full scale were carried out for a bulk carrier, once...

  10. Estimating Hull Coating Thickness Distributions Using the EM Algorithm

    National Research Council Canada - National Science Library

    Corriere, Michael

    2000-01-01

    The underwater hull coating system on surface ships is comprised anti-corrosive (AC) and anti-fouling (AF) paint The AF layers are designed to wear away, continuously leaching cuprous oxide to inhibit marine growth...

  11. Opvoeders se persepsies van hulle werkmotivering: 'n kwalitatiewe ...

    African Journals Online (AJOL)

    Erna Kinsey

    Individue voel dat hulle self geen beheer oor die proses het nie en dat die verandering van buite ...... treatment has a negative influence on their self-esteem and moti- vation. ... tion, especially since the abolishment of corporal punishment.

  12. Soybean hulls as an iron source for bread enrichment

    International Nuclear Information System (INIS)

    Johnson, C.D.; Berry, M.F.; Weaver, C.M.

    1985-01-01

    Soybean hulls, a concentrated source of iron, may have potential as a source of iron fortification in baked products. Retention of 59 Fe in rats from white bread containing intrinsically labeled soybean hulls did not differ significantly (p<0.05) from extrinsically labeled white bread fortified with bakery grade ferrous sulfate (70.4 and 63.1%, respectively). Physical and sensory evaluations of bread containing up to 5% soybean hulls did not differ from white bread in loaf volume, cross-sectional area, tenderness or overall acceptance. These results suggest that soybean hulls are a good source of available iron and may be added to bakery products without deleterious effects in baking performance and sensory acceptability

  13. Calculation for Hull Strength Construction in Offshore Structures

    African Journals Online (AJOL)

    PROF. O. E. OSUAGWU

    2013-09-01

    Sep 1, 2013 ... of hull plating, reinforcing stiffeners, girders, and other structures. This paper therefore used the .... From these equations we derive that. Safety of. Factor. Stress ..... machineries, systems etc. of the ships or barge under design.

  14. Ship with a double hull used to transport liquefied gases

    Energy Technology Data Exchange (ETDEWEB)

    1968-07-18

    A ship with a double hull is described which is used to transport liquefied gases in reservoirs which are held inside the inner hull by a glide support and surrounded by insulation. Troughs are situated at the bottom and along the adjacent ends of the side walls to catch leakage from the reservoirs. These catchers are made of a material which is tough when chilled. The catchers have a suction installation to remove the leaked fluid. (5 claims)

  15. Diatom community structure on in-service cruise ship hulls.

    Science.gov (United States)

    Hunsucker, Kelli Zargiel; Koka, Abhishek; Lund, Geir; Swain, Geoffrey

    2014-10-01

    Diatoms are an important component of marine biofilms found on ship hulls. However, there are only a few published studies that describe the presence and abundance of diatoms on ships, and none that relate to modern ship hull coatings. This study investigated the diatom community structure on two in-service cruise ships with the same cruise cycles, one coated with an antifouling (AF) system (copper self-polishing copolymer) and the other coated with a silicone fouling-release (FR) system. Biofilm samples were collected during dry docking from representative areas of the ship and these provided information on the horizontal and vertical zonation of the hull, and intact and damaged coating and niche areas. Diatoms from the genera Achnanthes, Amphora and Navicula were the most common, regardless of horizontal ship zonation and coating type. Other genera were abundant, but their presence was more dependent on the ship zonation and coating type. Samples collected from damaged areas of the hull coating had a similar community composition to undamaged areas, but with higher diatom abundance. Diatom fouling on the niche areas differed from that of the surrounding ship hull and paralleled previous studies that investigated differences in diatom community structure on static and dynamically exposed coatings; niche areas were similar to static immersion and the hull to dynamic immersion. Additionally, diatom richness was greater on the ship with the FR coating, including the identification of several new genera to the biofouling literature, viz. Lampriscus and Thalassiophysa. These results are the first to describe diatom community composition on in-service ship hulls coated with a FR system. This class of coatings appears to have a larger diatom community compared to copper-based AF systems, with new diatom genera that have the ability to stick to ship hulls and withstand hydrodynamic forces, thus creating the potential for new problematic species in the biofilm.

  16. Use of Jatropha curcas hull biomass for bioactive compost production

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, D.K. [Division of Environmental Sciences, Indian Agricultural Research Institute, New Delhi 110012 (India); Pandey, A.K.; Lata [Division of Microbiology, Indian Agricultural Research Institute, New Delhi 110012 (India)

    2009-01-15

    The paper deals with utilization of biomass of Jatropha hulls for production of bioactive compost. In the process of Jatropha oil extraction, a large amount of hull waste is generated. It has been found that the direct incorporation of hull into soil is considerably inefficient in providing value addition to soil due to its unfavorable physicochemical characteristics (high pH, EC and phenolic content). An alternative to this problem is the bioconversion of Jatropha hulls using effective lignocellulolytic fungal consortium, which can reduce the phytotoxicity of the degraded material. Inoculation with the fungal consortium resulted in better compost of jatropha hulls within 1 month, but it takes nearly 4 months for complete compost maturation as evident from the results of phytotoxicity test. Such compost can be applied to the acidic soil as a remedial organic manure to help maintaining sustainability of the agro-ecosystem. Likewise, high levels of cellulolytic enzymes observed during bioconversion indicate possible use of fungi for ethanol production from fermentation of hulls. (author)

  17. Preconditioning 2D Integer Data for Fast Convex Hull Computations.

    Science.gov (United States)

    Cadenas, José Oswaldo; Megson, Graham M; Luengo Hendriks, Cris L

    2016-01-01

    In order to accelerate computing the convex hull on a set of n points, a heuristic procedure is often applied to reduce the number of points to a set of s points, s ≤ n, which also contains the same hull. We present an algorithm to precondition 2D data with integer coordinates bounded by a box of size p × q before building a 2D convex hull, with three distinct advantages. First, we prove that under the condition min(p, q) ≤ n the algorithm executes in time within O(n); second, no explicit sorting of data is required; and third, the reduced set of s points forms a simple polygonal chain and thus can be directly pipelined into an O(n) time convex hull algorithm. This paper empirically evaluates and quantifies the speed up gained by preconditioning a set of points by a method based on the proposed algorithm before using common convex hull algorithms to build the final hull. A speedup factor of at least four is consistently found from experiments on various datasets when the condition min(p, q) ≤ n holds; the smaller the ratio min(p, q)/n is in the dataset, the greater the speedup factor achieved.

  18. Grene and Hull on types and typological thinking in biology.

    Science.gov (United States)

    Honenberger, Phillip

    2015-04-01

    Marjorie Grene (1910-2009) and David Hull (1935-2010) were among the most influential voices in late twentieth-century philosophy of biology. But, as Grene and Hull pointed out in published discussions of one another's work over the course of nearly forty years, they disagreed strongly on fundamental issues. Among these contested issues is the role of what is sometimes called "typology" and "typological thinking" in biology. In regard to taxonomy and the species problem, Hull joined Ernst Mayr's construal of typological thinking as a backward relic of pre-Darwinian science that should be overcome. Grene, however, treated the suspicion of typological thinking that characterized Hull's views, as well as those of other architects of the New Evolutionary Synthesis, as itself suspicious and even unsustainable. In this paper I review three debates between Grene and Hull bearing on the question of the validity of so-called typological thinking in biology: (1) a debate about the dispensability of concepts of "type" within evolutionary theory, paleontology, and taxonomy; (2) a debate about whether species can be adequately understood as individuals, and thereby independently of those forms of thinking Hull and Mayr had construed as "typological"; and (3) a debate about the prospects of a biologically informed theory of human nature. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Treatment of zircaloy cladding hulls by isostatic pressing

    International Nuclear Information System (INIS)

    Tegman, R.; Burstroem, M.

    1984-12-01

    A method for the treatment of Zircaloy fuel hulls is proposed. It involves hot isostatic pressing (HIP) for making large, completely densified metallic bodies of the waste. The hulls are packed into a bellows-shaped container of steel. On packing the fuel hulls give a filling factor of only 14%, which is too low for non-deformable compaction in a normal container, but by using a belloped container, a non-deformable compaction can be obtained without any pretreatment of the hulls. Fully dense and mechanically strong blocks of Zircaloy can be fabricated by holding them at temperatures of around 1000 degrees C for three hours. It is also feasible to incorporate the other metallic parts of the fuel bundle, such as top and bottom tie plates and spacers, in the pressing. The HIP-densified hulls provide an effective means of self-containment of radioactive waste due to the excellent corrosion resistance of Zircaloy. A waste loading factor of close to 100% can be realized. Futher, a volume reduction factor of 7 and a surface reduction factor of aout 250 for a 1-ton canister can be achieved. Equilibrium calculations have shown that tritium present in the hulls can quantitatively be contained in the HIPed block. A study has been made of a possible process for industrilscale use. (Author)

  20. Background matters: Minor vibratory stimulation during motor skill acquisition selectively reduces off-line memory consolidation.

    Science.gov (United States)

    Korman, Maria; Herling, Zohar; Levy, Ishay; Egbarieh, Nebal; Engel-Yeger, Batya; Karni, Avi

    2017-04-01

    Although a ubiquitous situation, it is not clear how effective is a learning experience when task-irrelevant, sensory noise occurs in the background. Here, young adults were trained on the finger opposition sequence task, in a well-established training and testing protocol affording measures for online as well as off-line learning. During the training session, one group experienced a minor background vibratory stimulation to the trunk by the means of vibrating cushion, while the second group experienced recorded sound vibrations. A control group was trained with no extra sensory stimulation. Sensory stimulation during training had no effect on the online within-session gains, but dampened the expression of the off-line, consolidation phase, gains in the two sensory stimulation groups. These results suggest that background sensory stimulation can selectively modify off-line, procedural memory consolidation processes, despite well-preserved on-line learning. Classical studies have shown that neural plasticity in sensory systems is modulated by motor input. The current results extend this notion and suggest that some types of task-irrelevant sensory stimulation, concurrent with motor training, may constitute a 'gating' factor - modulating the triggering of long-term procedural memory consolidation processes. Thus, vibratory stimulation may be considered as a behavioral counterpart of pharmacological interventions that do not interfere with short term neural plasticity but block long-term plasticity. Copyright © 2017 Elsevier Inc. All rights reserved.

  1. Obtention of hydroxyapatite submicrometric of bovine origin by vibratory grinding for rapid prototyping

    International Nuclear Information System (INIS)

    Meira, C.R.; Purquerio, B.M.; Fortulan, C.A.

    2011-01-01

    Submicron bovine hydroxyapatite was obtained for rapid prototyping. Hydroxyapatite structure originated from bovine mineral bone has great importance among the biomaterials and biocompatibility due to its great similarity with the human bone structure. This study aims to obtain powder for manufacture by rapid prototyping of scaffolds. This technique manufacture requires highly reactive powders to compensate for the absence of pressure forming. Hydroxyapatite was milled in a ball mill and vibratory mill, and analyzed for their average equivalent spherical diameter and surface area. Test specimens were isostatically pressed at 100 MPa and machined into cylindrical test specimens. These specimens were sintered at several temperatures to determine the optimal sintering temperature based on densification and chemistry stability. In grinding ball mill was obtained particles of equivalent diameter of 0.74 micron in vibratory mill of 0.46 micrometers. An average flexural strength of 100 MPa and 99,8% of real density was attained for the sample sintered at 1300 deg C/2h, signaling potential for use in rapid prototyping. (author)

  2. Structural-acoustic coupling effects on the non-vacuum packaging vibratory cylinder gyroscope.

    Science.gov (United States)

    Xi, Xiang; Wu, Xuezhong; Wu, Yulie; Zhang, Yongmeng; Tao, Yi; Zheng, Yu; Xiao, Dingbang

    2013-12-13

    The resonant shells of vibratory cylinder gyroscopes are commonly packaged in metallic caps. In order to lower the production cost, a portion of vibratory cylinder gyroscopes do not employ vacuum packaging. However, under non-vacuum packaging conditions there can be internal acoustic noise leading to considerable acoustic pressure which is exerted on the resonant shell. Based on the theory of the structural-acoustic coupling, the dynamical behavior of the resonant shell under acoustic pressure is presented in this paper. A finite element (FE) model is introduced to quantitatively analyze the effect of the structural-acoustic coupling. Several main factors, such as sealing cap sizes and degree of vacuum which directly affect the vibration of the resonant shell, are studied. The results indicate that the vibration amplitude and the operating frequency of the resonant shell will be changed when the effect of structural-acoustic coupling is taken into account. In addition, an experiment was set up to study the effect of structural-acoustic coupling on the sensitivity of the gyroscope. A 32.4 mV/°/s increase of the scale factor and a 6.2 Hz variation of the operating frequency were observed when the radial gap size between the resonant shell and the sealing cap was changed from 0.5 mm to 20 mm.

  3. Structural-Acoustic Coupling Effects on the Non-Vacuum Packaging Vibratory Cylinder Gyroscope

    Directory of Open Access Journals (Sweden)

    Xiang Xi

    2013-12-01

    Full Text Available The resonant shells of vibratory cylinder gyroscopes are commonly packaged in metallic caps. In order to lower the production cost, a portion of vibratory cylinder gyroscopes do not employ vacuum packaging. However, under non-vacuum packaging conditions there can be internal acoustic noise leading to considerable acoustic pressure which is exerted on the resonant shell. Based on the theory of the structural-acoustic coupling, the dynamical behavior of the resonant shell under acoustic pressure is presented in this paper. A finite element (FE model is introduced to quantitatively analyze the effect of the structural-acoustic coupling. Several main factors, such as sealing cap sizes and degree of vacuum which directly affect the vibration of the resonant shell, are studied. The results indicate that the vibration amplitude and the operating frequency of the resonant shell will be changed when the effect of structural-acoustic coupling is taken into account. In addition, an experiment was set up to study the effect of structural-acoustic coupling on the sensitivity of the gyroscope. A 32.4 mV/°/s increase of the scale factor and a 6.2 Hz variation of the operating frequency were observed when the radial gap size between the resonant shell and the sealing cap was changed from 0.5 mm to 20 mm.

  4. Evaluation of the biological activity of sunflower hull extracts

    Energy Technology Data Exchange (ETDEWEB)

    Taha, F. S.; Wagdy, S. M.; Hassanein, M. M. M.; Hamed, S. F.

    2012-11-01

    This work was planned with the aim of adding value to sunflower seed hulls, a waste product of the oil industry by preparing a sunflower hull phenolic extract rich in chlorogenic acid (CGA). In order to fulfill this goal, the optimization for the extraction of a phenolic extract from the hulls was investigated. The parameters studied were: type of solvent, solvent to water ratio and hull to solvent ratio. In addition, the solvent mixtures were also studied. The resulting phenolic extracts were evaluated for their biological activities. This included phenolic content determination, evaluation of the antioxidant and antimicrobial activities. Chlorogenic acid was determined in two chosen hull extracts using the UV spectrophotometric method and HPLC analysis. The anti carcinogenic activity of the two chosen extracts was tested on seven different cell line carcinomas. The results revealed that all the phenolic extracts of sunflower hull studied contain between 190-312.5 mg phenolics/ 100 g hulls. The highest phenolic extraction was achieved with 80% methanol (1:30, hull to solvent, w/v ratio) and methanol to ethanol to water (7:7:6 v/v/v) mixture with values of 312.5 and 306.5 mg phenolics/100 g hulls, respectively. The free radical scavenging activity and antioxidant activity of all the samples ranged from 33.6-72.6%. The highest antioxidant activity and free radical scavenging activity were achieved by the same extracts that possessed the highest phenolic content, namely methanol to ethanol to water extract and 80% methanol with values 71.8 and 72.6%, 68.2 and 70.9% respectively, compared to 77.9 and 76.9% respectively for TBHQ. All the phenolic extracts possessed antimicrobial activity but to different levels against different pathogenic bacteria. The two chosen extracts also possessed anti carcinogenic activity, which differed among varying cell line carcinomas. The HPLC analysis indicated that chlorogenic acid was the main phenolic acid in the extract. Thus it can

  5. Hull loss accident model for narrow body commercial aircraft

    Directory of Open Access Journals (Sweden)

    Somchanok Tiabtiamrat

    2010-10-01

    Full Text Available Accidents with narrow body aircraft were statistically evaluated covering six families of commercial aircraft includingBoeing B737, Airbus A320, McDonnell Douglas MD80, Tupolev TU134/TU154 and Antonov AN124. A risk indicator for eachflight phase was developed based on motion characteristics, duration time, and the presence of adverse weather conditions.The estimated risk levels based on these risk indicators then developed from the risk indicator. Regression analysis indicatedvery good agreement between the estimated risk level and the accident ratio of hull loss cases per number of delivered aircraft.The effect of time on the hull loss accident ratio per delivered aircraft was assessed for B737, A320 and MD80. Equationsrepresenting the effect of time on hull loss accident ratio per delivered aircraft were proposed for B737, A320, and MD80,while average values of hull loss accident ratio per delivered aircraft were found for TU134, TU154, and AN 124. Accidentprobability equations were then developed for each family of aircraft that the probability of an aircraft in a hull loss accidentcould be estimated for any aircraft family, flight phase, presence of adverse weather factor, hour of day, day of week, monthof year, pilot age, and pilot flight hour experience. A simplified relationship between estimated hull loss accident probabilityand unsafe acts by human was proposed. Numerical investigation of the relationship between unsafe acts by human andfatality ratio suggested that the fatality ratio in hull loss accident was dominated primarily by the flight phase media.

  6. Thermal springs of Wyoming

    Energy Technology Data Exchange (ETDEWEB)

    Breckenridge, R.M.; Hinckley, B.S.

    1978-01-01

    This bulletin attempts, first, to provide a comprehensive inventory of the thermal springs of Wyoming; second, to explore the geologic and hydrologic factors producing these springs; and, third, to analyze the springs collectively as an indicator of the geothermal resources of the state. A general discussion of the state's geology and the mechanisms of thermal spring production, along with a brief comparison of Wyoming's springs with worldwide thermal features are included. A discussion of geothermal energy resources, a guide for visitors, and an analysis of the flora of Wyoming's springs follow the spring inventory. The listing and analysis of Wyoming's thermal springs are arranged alphabetically by county. Tabulated data are given on elevation, ownership, access, water temperature, and flow rate. Each spring system is described and its history, general characteristics and uses, geology, hydrology, and chemistry are discussed. (MHR)

  7. Vibratory perception threshold in young and middle-aged patients at high risk of knee osteoarthritis compared to controls

    DEFF Research Database (Denmark)

    Thorlund, Jonas Bloch; Shakoor, Najia; Ageberg, Eva

    2012-01-01

    Vibratory perception threshold (VPT) is impaired in patients with knee osteoarthritis (OA). It is, however, not known if sensory deficits precede or follow as a consequence of OA. The aim of this study was to investigate VPT in 2 independent groups of patients with high risk of future OA (young a...

  8. Biofibres from biofuel industrial byproduct-Pongamia pinnata seed hull.

    Science.gov (United States)

    Manjula, Puttaswamy; Srinikethan, Govindan; Shetty, K Vidya

    2017-01-01

    Biodiesel production using Pongamia pinnata (P. pinnata) seeds results in large amount of unused seed hull. These seed hulls serve as a potential source for cellulose fibres which can be exploited as reinforcement in composites. These seed hulls were processed using chlorination and alkaline extraction process in order to isolate cellulose fibres. Scanning electron microscopy (SEM), dynamic light scattering (DLS), thermogravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR) analysis demonstrated the morphological changes in the fibre structure. Cellulose microfibres of diameter 6-8 µm, hydrodynamic diameter of 58.4 nm and length of 535 nm were isolated. Thermal stability was enhanced by 70 °C and crystallinity index (CI) by 19.8% ensuring isolation of crystalline cellulose fibres. The sequential chlorination and alkaline treatment stemmed to the isolation of cellulose fibres from P. pinnata seed hull. The isolated cellulose fibres possessed enhanced morphological, thermal, and crystalline properties in comparison with P. pinnata seed hull. These cellulose microfibres may potentially find application as biofillers in biodegradable composites by augmenting their properties.

  9. Development of hull compaction system for nuclear recycle facility

    International Nuclear Information System (INIS)

    Manole, A.A.; Karkhanis, P.P.; Agarwal, Kailash; Basu, Sekhar

    2013-01-01

    India has adopted closed fuel cycle strategy for efficient management of available resources to meet long term energy requirements. Nuclear Recycle Facility (NRF) provides a vital link in three-stage Indian nuclear power programme. In a NRF for PHWR fuel cycle, reprocessing of spent fuel bundles from PHWRs is carried out using a chop-leach process where the spent fuel bundles are chopped into small pieces using a spent fuel chopper and the contents inside the zircaloy clad are dissolved using concentric nitric acid. This process generates empty zircaloy shells called 'hulls'. The present practice followed for management of hulls is to transfer them into SS drums and store these drums in underground RCC tile holes at a Waste Management Facility (WMF). This waste needs to be stored in an engineered WMF for at least 30-60 years before transferred to a final repository. The storage volumes required for this hull waste will keep increasing as the reprocessing capacity is being enhanced multi-folds. Compaction of hull waste has been employed internationally to reduce the volume required for storage. Hence indigenous development of hull compaction system was initiated by NRB to meet the future requirements. This is being achieved through a set of experiments and analysis with the available resources within the country. This paper describes the process of compaction, conceptualization of the system and benefits accrued from it. (author)

  10. Region-of-interest volumetric visual hull refinement

    KAUST Repository

    Knoblauch, Daniel

    2010-01-01

    This paper introduces a region-of-interest visual hull refinement technique, based on flexible voxel grids for volumetric visual hull reconstructions. Region-of-interest refinement is based on a multipass process, beginning with a focussed visual hull reconstruction, resulting in a first 3D approximation of the target, followed by a region-of-interest estimation, tasked with identifying features of interest, which in turn are used to locally refine the voxel grid and extract a higher-resolution surface representation for those regions. This approach is illustrated for the reconstruction of avatars for use in tele-immersion environments, where head and hand regions are of higher interest. To allow reproducability and direct comparison a publicly available data set for human visual hull reconstruction is used. This paper shows that region-of-interest reconstruction of the target is faster and visually comparable to higher resolution focused visual hull reconstructions. This approach reduces the amount of data generated through the reconstruction, allowing faster post processing, as rendering or networking of the surface voxels. Reconstruction speeds support smooth interactions between the avatar and the virtual environment, while the improved resolution of its facial region and hands creates a higher-degree of immersion and potentially impacts the perception of body language, facial expressions and eye-to-eye contact. Copyright © 2010 by the Association for Computing Machinery, Inc.

  11. Instant Spring Tool Suite

    CERN Document Server

    Chiang, Geoff

    2013-01-01

    Filled with practical, step-by-step instructions and clear explanations for the most important and useful tasks. A tutorial guide that walks you through how to use the features of Spring Tool Suite using well defined sections for the different parts of Spring.Instant Spring Tool Suite is for novice to intermediate Java developers looking to get a head-start in enterprise application development using Spring Tool Suite and the Spring framework. If you are looking for a guide for effective application development using Spring Tool Suite, then this book is for you.

  12. Characterization of vibratory turning in cutting zone using a pneumatic quick-stop device

    Directory of Open Access Journals (Sweden)

    Saeid Amini

    2017-04-01

    Full Text Available Shear angle and sticking length are two crucial parameters in mechanics of metal cutting. These two parameters directly influence machinability factors such as cutting forces. Thus, shear angle and sticking length were investigated in vibratory turning process by using a pneumatic quick-stop device which was designed and fabricated, in this study. After preparation of ultrasonic assisted turning set-up, experimental tests have been carried out on two types of steel: AISI-1060 and AISI 304. Accordingly, the process of chip formation in each particular cutting test was quickly stopped when deformed chip was still in contact with workpiece. As a result, it was revealed that added linear vibration leads the turning operation to be improved by increase of shear angle and decrease of sticking length. Moreover, the effect of ultrasonic vibration on cutting force and chip micro-hardness is evaluated.

  13. Application of vibratory-percussion crusher for disintegration of supertough materials

    Science.gov (United States)

    Shishkin, E. V.; Kazakov, S. V.

    2017-10-01

    This article describes the results of theoretical and experimental studies of a vibratory-percussion crusher, which is driven from a pair of self-synchronizing vibration exciters, attached to the shell symmetrically about its vertical axis. In addition to that, crusher’s dynamic model is symmetrical and balanced. Forced oscillation laws for crusher working members and their amplitude-frequency characteristics have been inducted. Domains of existence of synchronous opposite-phase oscillations of crusher working members (crusher’s operating mode) and crusher capabilities have been identified. The results of mechanical and technological tests of a pilot crusher presented in the article show that this crusher may be viewed as an advanced machine for disintegration of supertough materials with minimum regrinding of finished products.

  14. Specific modes of vibratory technological machines: mathematical models, peculiarities of interaction of system elements

    Science.gov (United States)

    Eliseev, A. V.; Sitov, I. S.; Eliseev, S. V.

    2018-03-01

    The methodological basis of constructing mathematical models of vibratory technological machines is developed in the article. An approach is proposed that makes it possible to introduce a vibration table in a specific mode that provides conditions for the dynamic damping of oscillations for the zone of placement of a vibration exciter while providing specified vibration parameters in the working zone of the vibration table. The aim of the work is to develop methods of mathematical modeling, oriented to technological processes with long cycles. The technologies of structural mathematical modeling are used with structural schemes, transfer functions and amplitude-frequency characteristics. The concept of the work is to test the possibilities of combining the conditions for reducing loads with working components of a vibration exciter while simultaneously maintaining sufficiently wide limits in variating the parameters of the vibrational field.

  15. Bifurcation Analysis and Spatiotemporal Patterns in Unidirectionally Delay-Coupled Vibratory Gyroscopes

    Science.gov (United States)

    Li, Li; Xu, Jian

    Time delay is inevitable in unidirectionally coupled drive-free vibratory gyroscope system. The effect of time delay on the gyroscope system is studied in this paper. To this end, amplitude death and Hopf bifurcation induced by small time delay are first investigated by analyzing the related characteristic equation. Then, the direction of Hopf bifurcations and stability of Hopf-bifurcating periodic oscillations are determined by calculating the normal form on the center manifold. Next, spatiotemporal patterns of these Hopf-bifurcating periodic oscillations are analyzed by using the symmetric bifurcation theory of delay differential equations. Finally, it is found that numerical simulations agree with the associated analytic results. These phenomena could be induced although time delay is very small. Therefore, it is shown that time delay is an important factor which influences the sensitivity and accuracy of the gyroscope system and cannot be neglected during the design and manufacture.

  16. Anti-control of chaos of a permanent magnet DC motor system for vibratory compactors

    International Nuclear Information System (INIS)

    Wang Zheng; Chau, K.T.

    2008-01-01

    The purpose of this paper is to employ time-delay feedback to anti-control a permanent magnet DC (PMDC) motor system for vibratory compactors, and hence implement a new electrically chaotic compactor. Firstly, the dynamic model of the anti-controlled PMDC motor system and the proposed electrically chaotic compactor are formulated. Secondly, a nonlinear map is derived to analyze the chaotic criterion of the anti-controlled PMDC motor system. Then, numerical computations are used to investigate the dynamics of the proposed electrically chaotic compactor. Finally, a series of simulations are conducted to verify that the proposed electrically chaotic compactor not only offers better compaction effects than the conventional one, but also provides higher flexibility than the mechanically chaotic compactor

  17. Understanding the role of nonlinearities in the transduction of vibratory energy harvesters

    Science.gov (United States)

    Masana, Ravindra Shiva Charan

    The last two decades have witnessed several advances in micro-fabrication technologies and electronics, leading to the development of small, low-power devices for wireless sensing, data transmission, actuation, and medical implants. Unfortunately, the actual implementation of such devices in their respective environment has been hindered by the lack of scalable energy sources that are necessary to power and maintain them. Batteries, which remain the most commonly used power source, have not kept pace with the demands of these devices, especially in terms of energy density. In light of this challenge, the concept of vibratory energy harvesting has flourished in recent years as a possible alternative to power and maintain low-power electronics. While linear vibratory energy harvesters have received the majority of the literature's attention, a significant body of the current research activity is focused on the concept of purposeful inclusion of nonlinearities for broadband transduction. When compared to their linear resonant counterparts, nonlinear energy harvesters have a wider steady-state frequency bandwidth, leading to the common belief that they can be utilized to improve performance especially in random and non-stationary vibratory environments. This dissertation aims to critically investigate this belief by drawing a clearer picture of the role of nonlinearities in the transduction of energy harvesters and by defining the conditions under which nonlinearities can be used to enhance performance. To achieve this goal, the Thesis is divided into three parts. The first part investigates the performance of mono- and bi-stable energy harvesters under harmonic excitations and carries a detailed analysis of their relative performance. The second part investigates their response to broadband and narrowband random excitations and again analyzes their relative behavior. The third part exploits the super-harmonic resonance bands of bi-stable energy harvesters for the

  18. Study on the Effect of Steel Wheel and Ground on Single Steel Vibratory Roller

    Science.gov (United States)

    Li, Jiabo; You, Guanghui; Qiao, Jiabin; Ye, Min; Guo, Jin; Zhang, Hongyang

    2018-03-01

    In the compacting operation of single drum vibratory roller, the forces acting on the foundation of drum include the weight of the drum, the weight of the frame, the exciting force and so on. Based on the theoretical study of ground mechanics, this paper analyzes and calculates the forces acting on the steel wheel and the ground, and obtains the distribution of the laminar stress in the ground when the working plane vibrates. Derive the formula of dynamic compressive stress and static compressive stress in the foundation during vibration compaction. Through the compaction test of the soil trough of 20T single drum roller, the compressive stress data of the soil hydraulic field are obtained. The data of the dynamic compressive stress and the static compressive stress of each layer during the third compaction are obtained, and the theoretical research is verified.

  19. Optimal Draft requirement for vibratory tillage equipment using Genetic Algorithm Technique

    Science.gov (United States)

    Rao, Gowripathi; Chaudhary, Himanshu; Singh, Prem

    2018-03-01

    Agriculture is an important sector of Indian economy. Primary and secondary tillage operations are required for any land preparation process. Conventionally different tractor-drawn implements such as mouldboard plough, disc plough, subsoiler, cultivator and disc harrow, etc. are used for primary and secondary manipulations of soils. Among them, oscillatory tillage equipment is one such type which uses vibratory motion for tillage purpose. Several investigators have reported that the requirement for draft consumption in primary tillage implements is more as compared to oscillating one because they are always in contact with soil. Therefore in this paper, an attempt is made to find out the optimal parameters from the experimental data available in the literature to obtain minimum draft consumption through genetic algorithm technique.

  20. Vibratory synchronization transmission of a cylindrical roller in a vibrating mechanical system excited by two exciters

    Science.gov (United States)

    Zhang, Xueliang; Wen, Bangchun; Zhao, Chunyu

    2017-11-01

    In present work vibratory synchronization transmission (VST) of a cylindrical roller with dry friction in a vibrating mechanical system excited by two exciters, is studied. Using the average method, the criterion of implementing synchronization of two exciters and that of ensuring VST of a roller, are achieved. The criterion of stability of the synchronous states satisfies the Routh-Hurwitz principle. The influences of the structural parameters of the system to synchronization and stability, are discussed numerically, which can be served as the theoretical foundation for engineering designs. An experiment is carried out, which approximately verify the validity of the theoretical and numerical results, as well as the feasibility of the method used. Utilizing the VST theory of a roller, some types of vibrating crushing or grinding equipments, etc., can be designed.

  1. Numerical Simulation of Galvanic Corrosion Caused by Shaft Grounding Systems in Steel Ship Hulls

    National Research Council Canada - National Science Library

    Wang, Y

    2005-01-01

    .... This led to the accelerated corrosion of the exposed steel ship hull on paint holidays because of the substantial difference of the electric potentials between the steel ship hull and the nickel...

  2. The role of hull in germination and salinity tolerance in some ...

    African Journals Online (AJOL)

    hulled and dehulled) of sunflower seeds of Opal, Shelly (Confectionary) and Pactol (Oily) were tested to determine the effects of the hull on salinity tolerance during germination. Germination percentage (%), mean germination time (day), root and ...

  3. On the global ship hull bending energy in ship collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Li, Yujie

    2009-01-01

    During ship collisions part of the kinetic energy of the involved vessels immediately prior to contact is absorbed as energy dissipated by crushing of the hull structures, by friction and by elastic energy. The purpose of this report is to present an estimate of the elastic energy that can...... be stored in elastic hull vibrations during a ship collision. When a ship side is strengthened in order to improve the crashworthiness it has been argued in the scientific literature that a non-trivial part of the energy released for structural deformation during the collision can be absorbed as elastic...... energy in global ship hull vibrations, such that with strong ship sides less energy has to be spent in crushing of the striking ship bow and/or the struck ship side. In normal ship–ship collision analyses both the striking and struck ship are usually considered as rigid bodies where structural crushing...

  4. Onboard monitoring of fatigue damage rates in the hull girder

    DEFF Research Database (Denmark)

    Nielsen, Ulrik Dam; Jensen, Jørgen Juncher; Pedersen, Preben Terndrup

    2011-01-01

    Most new advanced ships have extensive data collection systems to be used for continuous monitoring of engine and hull performance, for voyage performance evaluation etc. Such systems could be expanded to include also procedures for stress monitoring and for decision support, where the most...... critical wave-induced ship extreme responses and fatigue damage accumulation can be estimated for hypothetical changes in ship course and speed in the automatically estimated wave environment.The aim of this paper is to outline a calculation procedure for fatigue damage rate prediction in hull girders...... taking into account whipping stresses. It is conceptually shown how such a method, which integrates onboard estimation of sea states, can be used to deduce decision support with respect to the accumulated fatigue damage in the hull girder.The paper firstly presents a set of measured full-scale wave...

  5. On the Global Ship Hull Bending Energy in Ship Collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Li, Y.

    2004-01-01

    During ship collisions part of the kinetic energy of the involved vessels prior to contact is absorbed as energy dissipated by crushing of the hull structures, by friction and by elastic energy. The purpose of this report is to present an estimate of the elastic energy that can be stored in elastic...... hull vibrations during a ship collision. When a ship side is strengthened in order to improve the crashworthiness it has been argued in the scientific literature that a non trivial part of the energy released for structural deformation during the collision can be absorbed as elastic energy in global...... ship hull vibrations, such that with strong ship sides less energy has to be spent in crushing of the striking ship bow and/or the struck ship side. In normal ship-ship collision analyses both the striking and struck ship are usually considered as rigid bodies where structural crushing is confined...

  6. ISOLATION AND CHARACTERIZATION OF NANOFIBRILLATED CELLULOSE FROM OAT HULLS

    Directory of Open Access Journals (Sweden)

    Giovanni B. Paschoal

    2015-05-01

    Full Text Available The objectives of this work were to investigate the microstructure, crystallinity and thermal stability of nanofibrillated cellulose obtained from oat hulls using bleaching and acid hydrolysis at a mild temperature (45 ºC followed by ultrasonication. The oat hulls were bleached with peracetic acid, and after bleaching, the compact structure around the cellulosic fibers was removed, and the bundles became individualized. The extraction time (30 or 60 min did not affect the properties of the nanofibrillated cellulose, which presented a higher crystallinity index and thermal stability than the raw material (oat hulls. The nanocellulose formed interconnected webs of tiny fibers with diameters of 70-100 nm and lengths of several micrometers, producing nanofibers with a relatively high aspect ratio, thus indicating that these materials are suitable for polymer reinforcement.

  7. Yeast hulls: effect on spontaneous fermentation in different vinification conditions

    Directory of Open Access Journals (Sweden)

    Rosa López

    2000-09-01

    Full Text Available The effect of the addition of yeast hulls in vinification was investigated during three consecutive years. The study was carried out in the experimental winery of C.I.D.A in La Rioja (Spain with free running white grape juice of the Viura variety. Four different vinifications were studied. In two of these vinifications, stuck fermentations were detected. In all the studies, the addition of yeast hulls (yeast ghosts improved the fermentation kinetics, increasing the number of viable yeasts at the end of the exponential stage and decreasing the final content of reducing sugars. This work revealed a new effect of yeast hull addition which had not been identified previously; their selection effect on the wild yeast strain in spontaneous fermentation.

  8. The interaction of extreme waves with hull elements

    Science.gov (United States)

    Galiev, Shamil; Flay, Richard

    2010-05-01

    The problem of the impact of a rogue wave onto a deformable marine structure is formulated in a few publications (see, for example, a short review in http://researchspace.auckland.ac.nz/handle/2292/4474). In this paper the results from numerical and experimental investigations of the effect of cavitation on the deformation of a hull element, loaded by a wall of water, generated by an extreme ocean surface wave are considered. The hull element is modelled as a circular metal plate with the edge of the plate rigidly clamped. The plate surface is much smaller than the surface of the wave front, so that at the initial moment of the interaction, the pressure is constant on the plate surface. At the next instant, because of the plate deformation, axisymmetric loading of the plate occurs. The influences of membrane forces and plastic deformations are ignored, and therefore, the equation of plate motion has the following classical form Eh3(wrrrr+2r -1wrrrr- r-2wrr+r-3wr) = - 121- ν2)[ρhwtt+ δ(r,t)(p+ ρ0a0wt)]. Here w is the plate displacement, subscripts t and rindicate derivatives with respect to time and the radial coordinate, PIC is the plate material density, his the plate thickness, Eis Young's modulus, PIC is Poisson's ratio and p is the pressure of the incident surface wave measured on the wall, PIC is the water density, PIC is the speed of sound in water, and PIC is the normal velocity of the plate. The term PIC takes into account the effect of the deformability of the plate. Obviously, the hull of a vessel is not rigid like a solid wall, but starts to deform and to move. This motion produces a reflected pressure wave, which travels from the hull into the water wave with a magnitude equal to PIC . The normal velocity is positive so the reflected pressure PIC is negative (tensile wave). If the fluid pressure drops below some critical value pk, the wet plate surface separates from the water, and cavitation may be generated. The function δ(r,t) takes into account

  9. A novel oscillation control for MEMS vibratory gyroscopes using a modified electromechanical amplitude modulation technique

    International Nuclear Information System (INIS)

    Ma, Wei; Lin, Yiyu; Liu, Siqi; Zheng, Xudong; Jin, Zhonghe

    2017-01-01

    This paper reports a novel oscillation control algorithm for MEMS vibratory gyroscopes using a modified electromechanical amplitude modulation (MEAM) technique, which enhances the robustness against the frequency variation of the driving mode, compared to the conventional EAM (CEAM) scheme. In this approach, the carrier voltage exerted on the proof mass is frequency-modulated by the drive resonant frequency. Accordingly, the pick-up signal from the interface circuit involves a constant-frequency component that contains the amplitude and phase information of the vibration displacement. In other words, this informational detection signal is independent of the mechanical resonant frequency, which varies due to different batches, imprecise micro-fabrication and changing environmental temperature. In this paper, the automatic gain control loop together with the phase-locked loop are simultaneously analyzed using the averaging method and Routh–Hurwitz criterion, deriving the stability condition and the parameter optimization rules of the transient response. Then, a simulation model based on the real system is set up to evaluate the control algorithm. Further, the proposed MEAM method is tested using a field-programmable-gate-array based digital platform on a capacitive vibratory gyroscope. By optimizing the control parameters, the transient response of the drive amplitude reveals a settling time of 45.2 ms without overshoot, according well with the theoretical prediction and simulation results. The first measurement results show that the amplitude variance of the drive displacement is 12 ppm in an hour while the phase standard deviation is as low as 0.0004°. The mode-split gyroscope operating under atmospheric pressure demonstrates an outstanding performance. By virtue of the proposed MEAM method, the bias instability and angle random walk are measured to be 0.9° h −1 (improved by 2.4 times compared to the CEAM method) and 0.068° (√h) −1 (improved by 1

  10. Vibratory function and healing outcomes after small intestinal submucosa biomaterial implantation for chronic vocal fold scar.

    Science.gov (United States)

    Pitman, Michael J; Kurita, Takashi; Powell, Maria E; Kimball, Emily E; Mizuta, Masanobu; Chang, Siyuan; Garrett, C Gaelyn; Rousseau, Bernard

    2018-04-01

    Vocal fold scar is a major cause of dysphonia, and optimal treatments do not currently exist. Small intestinal submucosa (SIS) is a biomaterial developed for the treatment of a variety of pathologies. The purpose of this study was to investigate the effects of SIS implantation on tissue remodeling in scarred vocal folds using routine staining, immunohistochemistry, and high-speed videoendoscopy (HSV). Prospective, blinded group analysis. Thirteen New Zealand White rabbits underwent a vocal fold scarring procedure followed by microflap elevation with or without SIS implantation. Seven months later, they underwent a phonation procedure with HSV and laryngeal harvest. Alcian blue and elastica van Gieson staining and immunohistochemistry for collagen types I and III were used to evaluate histological healing outcomes. Dynamic functional remodeling of the scarred vocal fold in the presence of SIS implants was evaluated using HSV imaging to capture restoration of vibratory amplitude, amplitude ratio, and left-right phase symmetry. Density of collagen I was significantly decreased in SIS versus microflap-treated vocal folds. No differences were found between groups for hyaluronic acid, elastin, or collagen type III. Organization of elastin in the subepithelial region appeared to affect amplitude of vibration and the shape of the vocal fold edge. SIS implantation into chronic scar reduced the density of collagen I deposits. There was no evidence of a negative impact or complication from SIS implantation. Regardless of treatment type, organization of elastin in the subepithelial region may be important to vibratory outcomes. NA. Laryngoscope, 128:901-908, 2018. © 2017 The American Laryngological, Rhinological and Otological Society, Inc.

  11. 46 CFR 154.182 - Contiguous hull structure: Production weld test.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous hull structure: Production weld test. 154.182... Equipment Hull Structure § 154.182 Contiguous hull structure: Production weld test. If a portion of the contiguous hull structure is designed for a temperature colder than −34 °C (−30 °F) and is not part of the...

  12. Convex Hull Abstraction in Specialisation of CLP Programs

    DEFF Research Database (Denmark)

    Peralta, J.C.; Gallagher, John Patrick

    2003-01-01

    We introduce an abstract domain consisting of atomic formulas constrained by linear arithmetic constraints (or convex hulls). This domain is used in an algorithm for specialization of constraint logic programs. The algorithm incorporates in a single phase both top-down goal directed propagation...... and bottom-up answer propagation, and uses a widening on the convex hull domain to ensure termination. We give examples to show the precision gained by this approach over other methods in the literature for specializing constraint logic programs. The specialization method can also be used for ordinary logic...

  13. Drag Reduction trough Special paints Coated on the hull

    OpenAIRE

    Izaguirre Alza, Patricia; Pérez Rojas, Luis; Núñez Basáñez, José Fernando

    2010-01-01

    The economic recession, the environmental impact as well as the continuous fossil fuel consumption encourage actions that focus on saving energy. In the vessels sector, one of the main objectives has always been to reach a hydro-dynamically optimum hull which gave the desired speed with minimum power. Hydrodynamic drag is basically divided into two parts: a) the friction between the water and the hull, and b) the wave generation due to the free-surface air-water. Presented in this paper...

  14. 46 CFR 71.15-1 - Standards in inspection of hulls, boilers, and machinery.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery..., boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels, the standards... and inspection of hulls, boilers, and machinery, and the certificate of classification referring...

  15. Heat-treated hull flour does not affect iron bioavailability in rats.

    Science.gov (United States)

    Martino, Hércia Stampini Duarte; Carvalho, Ariela Werneck de; Silva, Cassiano Oliveira da; Dantas, Maria Inês de Souza; Natal, Dorina Isabel Gomes; Ribeiro, Sônia Machado Rocha; Costa, Neuza Maria Brunoro

    2011-06-01

    In this study the chemical composition and iron bioavailability of hull and hull-less soybean flour from the new cultivar UFVTN 105AP was evaluated. The hemoglobin depletion-repletion method was used in Wistar rats. Soybean hull flour presented 37% more total dietary fiber and higher content of iron than hull-less soybean flour. The phytate:iron molar ratio, however, was 2-fold lower in the soybean hull flour in compared to the hull-less soybean flour. Animals fed soybean hull flour presented hemoglobin gains similar to those of the control diet group (p > 0.05). The Relative Biological Values of hull and hull-less soybean flour were 68.5% and 67.1%, respectively, compared to the control group. Heat-treated soybean hull flour (150 degrees C/30 minutes) showed high content of iron and low phytate, which favors the iron bioavailability. Thus, the soybean hull flour is a better source of dietary fiber and iron than hull-less soybean flour at comparable bioavailabilities.

  16. 14 CFR 25.533 - Hull and main float bottom pressures.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float bottom pressures. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.533 Hull and main float bottom pressures. (a) General. The hull and main float structure, including frames and bulkheads...

  17. 46 CFR 32.63-20 - Hull structure-B/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Hull structure-B/ALL. 32.63-20 Section 32.63-20 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS SPECIAL EQUIPMENT, MACHINERY, AND HULL REQUIREMENTS Hull and Cargo Tank Requirements for Tank Barges Constructed or Converted On or After July 1, 1964...

  18. 46 CFR 115.660 - Continued participation in the Alternative Hull Examination (AHE) Program.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Continued participation in the Alternative Hull... MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.660 Continued participation in the Alternative Hull Examination (AHE) Program. (a) To continue to participate in...

  19. 46 CFR 71.50-31 - Continued participation in the Alternative Hull Examination (AHE) program.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Continued participation in the Alternative Hull... the Alternative Hull Examination (AHE) program. (a) To continue to participate in the AHE Program, vessel operators must conduct an annual hull condition assessment. At a minimum, vessel operators must...

  20. 46 CFR 176.660 - Continued participation in the Alternative Hull Examination (AHE) Program.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Continued participation in the Alternative Hull... (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.660 Continued participation in the Alternative Hull Examination (AHE) Program. (a) To...

  1. 46 CFR 45.135 - Hull openings at or below freeboard deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Hull openings at or below freeboard deck. 45.135 Section 45.135 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.135 Hull openings at or below freeboard deck. Closures for hull...

  2. 14 CFR 23.529 - Hull and main float landing conditions.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float landing conditions. 23... Water Loads § 23.529 Hull and main float landing conditions. (a) Symmetrical step, bow, and stern... directed perpendicularly to the keel line. (b) Unsymmetrical landing for hull and single float seaplanes...

  3. 14 CFR 23.531 - Hull and main float takeoff condition.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float takeoff condition. 23.531 Section 23.531 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... Water Loads § 23.531 Hull and main float takeoff condition. For the wing and its attachment to the hull...

  4. Of Curriculum Conceptions, Orientations, and Cultures: A Rejoinder to John E. Hull

    Science.gov (United States)

    Van Brummelen, Harro

    2009-01-01

    In this article, the author presents a rejoinder to John E. Hull. Van Brummelen first states his appreciation of John Hull's thoughtful evaluation of his views of curriculum, views in which many Christian educators have played a part. It has been several decades since the author spelled out what Hull calls an "education for discipleship"…

  5. 33 CFR 80.135 - Hull, MA to Race Point, MA.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Hull, MA to Race Point, MA. 80... INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Atlantic Coast § 80.135 Hull, MA to Race Point, MA. (a... the east coast of Massachusetts from the easternmost radio tower at Hull, charted in approximate...

  6. 14 CFR 25.527 - Hull and main float load factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float load factors. 25.527... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.527 Hull and main... 1=empirical hull station weighing factor, in accordance with figure 2 of appendix B. (7) r x=ratio...

  7. 46 CFR 42.09-30 - Additional survey requirements for steel-hull vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Additional survey requirements for steel-hull vessels...-30 Additional survey requirements for steel-hull vessels. (a) In addition to the requirements in § 42...) When the vessel is in drydock, the hull plating, etc., shall be examined. (c) The holds, 'tween decks...

  8. 33 CFR Appendix G to Part 157 - Timetables for Application of Double Hull Requirements

    Science.gov (United States)

    2010-07-01

    ... Double Hull Requirements G Appendix G to Part 157 Navigation and Navigable Waters COAST GUARD, DEPARTMENT... Application of Double Hull Requirements 1. Source. These timetables conform to 46 U.S.C. 3703a(c). 2... double hull or with a double containment system determined by the Coast Guard to be as effective as a...

  9. 46 CFR 31.10-20 - Definitions relating to hull examinations-T/B ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Definitions relating to hull examinations-T/B ALL. 31.10... CERTIFICATION Inspections § 31.10-20 Definitions relating to hull examinations—T/B ALL. As used in this part— (a... examination of all accessible parts of the vessel's underwater body and all through-hull fittings. (b...

  10. 14 CFR 23.527 - Hull and main float load factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float load factors. 23.527... Water Loads § 23.527 Hull and main float load factors. (a) Water reaction load factors nw must be...=seaplane landing weight in pounds. (6) K1=empirical hull station weighing factor, in accordance with figure...

  11. 33 CFR 181.27 - Information displayed near hull identification number.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Information displayed near hull... displayed near hull identification number. With the exception of the characters “US-”, which constitute the... the 12-character hull identification number (HIN), that information must be separated from the HIN by...

  12. 46 CFR 176.630 - The Alternative Hull Examination (AHE) Program application.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false The Alternative Hull Examination (AHE) Program... PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.630 The Alternative Hull Examination (AHE) Program application. If your vessel meets the eligibility...

  13. 46 CFR 91.40-1 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 91.40-1... VESSELS INSPECTION AND CERTIFICATION Drydocking § 91.40-1 Definitions relating to hull examinations. As...-hull fittings. (b) Internal structural examination means an examination of the vessel while afloat or...

  14. 46 CFR 71.50-25 - Alternative Hull Examination (AHE) procedure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) procedure. 71.50-25... INSPECTION AND CERTIFICATION Drydocking § 71.50-25 Alternative Hull Examination (AHE) procedure. (a) To complete the underwater survey you must— (1) Perform a general examination of the underwater hull plating...

  15. 46 CFR 176.650 - Alternative Hull Examination Program options: Divers or underwater ROV.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Alternative Hull Examination Program options: Divers or...) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.650 Alternative Hull Examination Program options: Divers or underwater ROV. To complete the...

  16. 14 CFR 25.529 - Hull and main float landing conditions.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float landing conditions. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.529 Hull and main.... (b) Unsymmetrical landing for hull and single float seaplanes. Unsymmetrical step, bow, and stern...

  17. 78 FR 50335 - Double Hull Tanker Escorts on the Waters of Prince William Sound, Alaska

    Science.gov (United States)

    2013-08-19

    ...-AB96 Double Hull Tanker Escorts on the Waters of Prince William Sound, Alaska AGENCY: Coast Guard, DHS... mandates two tug escorts for double hull tankers over 5,000 gross tons transporting oil in bulk in PWS. The... tug escort requirements apply to certain double hull tankers. DATES: This interim rule is effective...

  18. 46 CFR 108.133 - Hull superstructure, structural bulkheads, decks, and deckhouses.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull superstructure, structural bulkheads, decks, and deckhouses. 108.133 Section 108.133 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A... Protection § 108.133 Hull superstructure, structural bulkheads, decks, and deckhouses. Each hull...

  19. 46 CFR 71.50-19 - The Alternative Hull Examination (AHE) Program application.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false The Alternative Hull Examination (AHE) Program...) PASSENGER VESSELS INSPECTION AND CERTIFICATION Drydocking § 71.50-19 The Alternative Hull Examination (AHE... apply to the AHE Program. You must submit an application at least 90 days before the requested hull...

  20. 46 CFR 189.40-1 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 189.40-1... VESSELS INSPECTION AND CERTIFICATION Drydocking § 189.40-1 Definitions relating to hull examinations. As...-hull fittings. (b) Internal structural examination means an examination of the vessel while afloat or...

  1. 46 CFR 115.650 - Alternative Hull Examination (AHE) Program options: Divers or underwater ROV.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) Program options... MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.650 Alternative Hull Examination (AHE) Program options: Divers or underwater ROV. To complete your underwater...

  2. 14 CFR 25.531 - Hull and main float takeoff condition.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float takeoff condition. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.531 Hull and main float takeoff condition. For the wing and its attachment to the hull or main float— (a) The aerodynamic...

  3. 77 FR 29251 - Safety Zone; Carnival Fireworks Display, Nantasket Beach, Hull, MA

    Science.gov (United States)

    2012-05-17

    ...-AA00 Safety Zone; Carnival Fireworks Display, Nantasket Beach, Hull, MA AGENCY: Coast Guard, DHS... zone on the navigable waters off of Nantasket Beach in the vicinity of Hull, MA for a Carnival... spectators and vessels from the hazards associated with fireworks displays. Discussion of Proposed Rule Hull...

  4. 46 CFR 167.15-27 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 167.15-27... PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-27 Definitions relating to hull examinations. As used... slipway for an examination of all accessible parts of the vessel's underwater body and all through-hull...

  5. 7 CFR 319.8-9 - Hull fiber and gin trash.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 5 2010-01-01 2010-01-01 false Hull fiber and gin trash. 319.8-9 Section 319.8-9 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION... Importation and Entry of Cotton and Covers § 319.8-9 Hull fiber and gin trash. (a) Entry of hull fiber will be...

  6. Management of waste cladding hulls. Part II. An assessment of zirconium pyrophoricity and recommendations for handling waste hulls

    International Nuclear Information System (INIS)

    Kullen, B.J.; Levitz, N.M.; Steindler, M.J.

    1977-11-01

    This report reviews experience and research related to the pyrophoricity of zirconium and zirconium alloys. The results of recent investigations of the behavior of Zircaloy and some observations of industrial handling and treatment of Zircaloy tubing and scrap are also discussed. A model for the management of waste Zircaloy cladding hulls from light water reactor fuel reprocessing is offered, based on an evaluation of the reviewed information. It is concluded that waste Zircaloy cladding hulls do not constitute a pyrophoric hazard if, following the model flow sheet, finely divided metal is oxidized during the management procedure. Steps alternative to the model are described which yield zirconium in deactivated form and also accomplish varying degrees of transuranic decontamination. Information collected into appendixes is (1) a collation of zirconium pyrophoricity data from the literature, (2) calculated radioactivity contents in Zircaloy cladding hulls from spent LWR fuels, and (3) results of a laboratory study on volatilization of zirconium from Zircaloy using HCl or Cl 2

  7. Pro Spring Batch

    CERN Document Server

    Minella, Michael T

    2011-01-01

    Since its release, Spring Framework has transformed virtually every aspect of Java development including web applications, security, aspect-oriented programming, persistence, and messaging. Spring Batch, one of its newer additions, now brings the same familiar Spring idioms to batch processing. Spring Batch addresses the needs of any batch process, from the complex calculations performed in the biggest financial institutions to simple data migrations that occur with many software development projects. Pro Spring Batch is intended to answer three questions: *What? What is batch processing? What

  8. Sampling of Stochastic Input Parameters for Rockfall Calculations and for Structural Response Calculations Under Vibratory Ground Motion

    International Nuclear Information System (INIS)

    M. Gross

    2004-01-01

    The purpose of this scientific analysis is to define the sampled values of stochastic (random) input parameters for (1) rockfall calculations in the lithophysal and nonlithophysal zones under vibratory ground motions, and (2) structural response calculations for the drip shield and waste package under vibratory ground motions. This analysis supplies: (1) Sampled values of ground motion time history and synthetic fracture pattern for analysis of rockfall in emplacement drifts in nonlithophysal rock (Section 6.3 of ''Drift Degradation Analysis'', BSC 2004 [DIRS 166107]); (2) Sampled values of ground motion time history and rock mechanical properties category for analysis of rockfall in emplacement drifts in lithophysal rock (Section 6.4 of ''Drift Degradation Analysis'', BSC 2004 [DIRS 166107]); (3) Sampled values of ground motion time history and metal to metal and metal to rock friction coefficient for analysis of waste package and drip shield damage to vibratory motion in ''Structural Calculations of Waste Package Exposed to Vibratory Ground Motion'' (BSC 2004 [DIRS 167083]) and in ''Structural Calculations of Drip Shield Exposed to Vibratory Ground Motion'' (BSC 2003 [DIRS 163425]). The sampled values are indices representing the number of ground motion time histories, number of fracture patterns and rock mass properties categories. These indices are translated into actual values within the respective analysis and model reports or calculations. This report identifies the uncertain parameters and documents the sampled values for these parameters. The sampled values are determined by GoldSim V6.04.007 [DIRS 151202] calculations using appropriate distribution types and parameter ranges. No software development or model development was required for these calculations. The calculation of the sampled values allows parameter uncertainty to be incorporated into the rockfall and structural response calculations that support development of the seismic scenario for the

  9. Electroglottographic parameterization of the effects of gender, vowel and phonatory registers on vocal fold vibratory patterns: an Indian perspective.

    Science.gov (United States)

    Paul, Nilanjan; Kumar, Suman; Chatterjee, Indranil; Mukherjee, Biswarup

    2011-01-01

    In-depth study on laryngeal biomechanics and vocal fold vibratory patterns reveal that a single vibratory cycle can be divided into two major phases, the closed and open phase, which is subdivided into opening and closing phases. Studies reveal that the relative time course of abduction and adduction, which in turn is dependent on the relative relaxing and tensing of the vocal fold cover and body, to be the determining factor in production of a particular vocal register like the modal (or chest), falsetto, glottal fry registers. Studies further point out Electroglottography to be particularly suitable for the study of vocal vibratory patterns during register changes. However, to date, there has been limited study on quantitative parameterization of EGG wave form in vocal fry register. Moreover, contradictory findings abound in literature regarding effects of gender and vowel types on vocal vibratory patterns, especially during phonation at different registers. The present study endeavors to find out the effects of vowel and gender differences on the vocal fold vibratory patterns in different registers and how these would be reflected in standard EGG parameters of Contact Quotient (CQ) and Contact Index (CI), taking into consideration the Indian sociolinguistic context. Electroglottographic recordings of 10 young adults (5 males and 5 females) were taken while the subjects phonated the three vowels /a/,/i/,/u/ each in two vocal registers, modal and vocal fry. Obtained raw EGG were further normalized using the Derived EGG algorithm and theCQ and CI values were derived. Obtained data were subject to statistical analysis using the 3-way ANOVA with gender, vowel and vocal register as the three variables. Post-hoc Dunnett C multiple comparison analysis were also performed. Results reveal that CQ values are significantly higher in vocal fry than modal phonation for both males and females, indicating a relatively hyperconstricted vocal system during vocal fry. The males

  10. The Hull Method for Selecting the Number of Common Factors

    Science.gov (United States)

    Lorenzo-Seva, Urbano; Timmerman, Marieke E.; Kiers, Henk A. L.

    2011-01-01

    A common problem in exploratory factor analysis is how many factors need to be extracted from a particular data set. We propose a new method for selecting the number of major common factors: the Hull method, which aims to find a model with an optimal balance between model fit and number of parameters. We examine the performance of the method in an…

  11. "Keisri hull" pürib taas filmiks

    Index Scriptorium Estoniae

    2008-01-01

    Eesti Filmi Sihtasutus otsustas anda arendustoetust mängufilmidele "Keisri hull" (režissöör Peeter Simm, arendaja Lege Artis Film), "Rahad ette" (režissöör Jaak Kilmi, arendaja Eetriüksus), "Öölendurid" (režissöör Peeter Urbla, arendaja Exitfilm)

  12. Double hull oil tankers - how effective are they?

    International Nuclear Information System (INIS)

    Keith, V.F.

    1993-01-01

    The groundings of the Exxon Valdez on Bligh Reef in Prince William Sound, spilling more than 10 million gallons of Alaska North Slope crude, and the American Trader off Huntington Beach, spilling almost 400,000 gallons of Alaska North Slope crude, suggest that the construction of oil tankers be re-examined with respect to a design which could reduce both the number and magnitude of oil spills. This paper discusses state-of-the-art tanker technology with respect to spill prevention, effectiveness, and cost. The design features include double hulls, centralized bunker tankers, vacuum-retaining valves, cargo control systems, auxiliary thrusters, electronic charting, and the retransmission of the ship's position. Double hulls provide the highest probability of surviving damage, either from a collision or grounding, with no loss of cargo. Use of double hulls can reduce oil spill incidence by 90 percent in grounding situations and by 75 percent in collisions. The oil spill from the AmericanTrader could have been completely avoided by double hull construction. The arrangement provides spaces below the cargo tanks and on the vessel's sides solely for the carriage of ballast water when the tanker is in ballast condition. These tanks are empty when the tanker is loaded and then also act as the first line of defense in the event of structural damage to the cargo tanks. Tanker design is integrated with port safety measures, including vessel monitoring systems, in this total spill prevention analysis. All aspects of the tanker transportation system are considered

  13. Water Pressure Distribution on a Flying Boat Hull

    Science.gov (United States)

    Thompson, F L

    1931-01-01

    This is the third in a series of investigations of the water pressures on seaplane floats and hulls, and completes the present program. It consisted of determining the water pressures and accelerations on a Curtiss H-16 flying boat during landing and taxiing maneuvers in smooth and rough water.

  14. Hybrid Wireless Hull Monitoring System for Naval Combat Vessels

    Science.gov (United States)

    2010-03-01

    Payload Data Acquisition System (SPDAS) is designed by the Technology Management Group, Inc. ( TMG ). In its design, the monitoring system is intended...monitoring system custom designed by TMG for the U.S. Navy. The Scientific Payload Data Acquisition System (SPDAS) is a wired hull monitoring system

  15. Leaching behavior of water-soluble carbohydrates from almond hulls

    Science.gov (United States)

    Over 58% of the dry matter content of the hulls from the commercial almond (Prunus dulcis (Miller) D.A. Webb) is soluble in warm water (50-70°C) extraction. The water-soluble extractables include useful amounts of fermentable sugars (glucose, fructose, sucrose), sugar alcohols (inositol and sorbito...

  16. PAUT-based defect detection method for submarine pressure hulls

    Directory of Open Access Journals (Sweden)

    Min-jae Jung

    2018-03-01

    Full Text Available A submarine has a pressure hull that can withstand high hydraulic pressure and therefore, requires the use of highly advanced shipbuilding technology. When producing a pressure hull, periodic inspection, repair, and maintenance are conducted to maintain its soundness. Of the maintenance methods, Non-Destructive Testing (NDT is the most effective, because it does not damage the target but sustains its original form and function while inspecting internal and external defects. The NDT process to detect defects in the welded parts of the submarine is applied through Magnetic particle Testing (MT to detect surface defects and Ultrasonic Testing (UT and Radiography Testing (RT to detect internal defects. In comparison with RT, UT encounters difficulties in distinguishing the types of defects, can yield different results depending on the skills of the inspector, and stores no inspection record. At the same time, the use of RT gives rise to issues related to worker safety due to radiation exposure. RT is also difficult to apply from the perspectives of the manufacturing of the submarine and economic feasibility. Therefore, in this study, the Phased Array Ultrasonic Testing (PAUT method was applied to propose an inspection method that can address the above disadvantages by designing a probe to enhance the precision of detection of hull defects and the reliability of calculations of defect size. Keywords: Submarine pressure hull, Non-destructive testing, Phased array ultrasonic testing

  17. Production of furfural and ethyl alcohol from cottonseed hulls

    Energy Technology Data Exchange (ETDEWEB)

    Bobovnikov, B M; Tsirlin, Yu A; Chepigo, S V; Shpuntova, M E

    1957-01-01

    Cottonseed hulls (8.3 tons per digester) and H/sub 2/SO/sub 4/ solution at temperature of 100/sup 0/ were added to the digester simultaneously. The final H/sub 2/SO/sub 4/ concentration of the charge was approximately 0.7%. The pentosans were hydrolyzed at 133/sup 0/ and 2 atmosphere for 6 hours and 15 minutes, then the temperature was raised to 179/sup 0/ at the top and to 150/sup 0/ at the bottom of the digester for 5 hours and 30 minutes. The hydrolytic products of pentosan were separated, neutralized, and transferred to a dehydration tank. The hexosans were then hydrolyzed at 179 to 187/sup 0/. Dry hulls gave 19.4% of pentose reducing sugars, of which 81.4% were fermented. One ton of dry hulls gave 74 to 79 l. of ethanol. The optimum condition for dehydration was at 165 to 175/sup 0/ for no longer than 4 to 4.5 hours. 2-Furaldehyde was produced in the following steps: the pentosan hydrolyzate was dehydrated with steam, the vapor-furaldehyde mixture was then reheated and finally distilled in a continuous column. The yield of furaldehyde was 36 to 37% of incoming pentoses (7% of dry hulls).

  18. Full scale leak test of the MEGAPIE containment hull

    Energy Technology Data Exchange (ETDEWEB)

    Samec, K

    2006-07-15

    The Full Scale Leak Test (FSLT) experiment is designed to replicate an accidental leak of Lead-Bismuth Eutectic (LBE) liquid metal from the MEGAPIE neutron spallation source. The neutron source is totally encased in an aluminum containment hull cooled by heavy water. Any liquid metal which would, in a hypothetical accident, leak into the helium-filled insulation gap between the source and the aluminum containment hull, would immediately impact the hull. Furthermore, during irradiation in the PSI SINQ facility, the LBE in the MEGAPIE Lower Liquid Metal Container (LLMC) accumulates radio-active substances which, in the event of a leak, must be cooled and contained under controlled conditions, as they may otherwise contaminate the facility. The FSLT experiment has been devised to fully test the structural integrity of the containment hull against a sudden liquid metal leak, and in addition, to resolve the peak temperature of he coolant, to validate the sensors used in detecting a leak and of proof-test the analytical methods used in predicting the consequences of a leak. The FSLT experiment has been analysed ahead of the test, and both thermal and structural aspects calculated using commercial codes. The predictions applied conservative assumptions to the analysis of the thermal shock so as to preclude the likelihood of an unforeseen failure of the hull. In this document, these initial predictions are compared to the temperature and strain data recorded in the experiment. Further analysis, to be published at a later stage, will focus on applying actual conditions realised in the experiment, as opposed to the envelope case used in the test predictions. The integrity of the containment hull under loads resulting from liquid metal-leak is therefore the focal point of the experiment described in the current document, and serves as a key reference test for the Iicensing of the facility. The data recorded during the SLT experiment shows that the MEGAPIE containment hull is

  19. Full scale leak test of the MEGAPIE containment hull

    International Nuclear Information System (INIS)

    Samec, K.

    2006-07-01

    The Full Scale Leak Test (FSLT) experiment is designed to replicate an accidental leak of Lead-Bismuth Eutectic (LBE) liquid metal from the MEGAPIE neutron spallation source. The neutron source is totally encased in an aluminum containment hull cooled by heavy water. Any liquid metal which would, in a hypothetical accident, leak into the helium-filled insulation gap between the source and the aluminum containment hull, would immediately impact the hull. Furthermore, during irradiation in the PSI SINQ facility, the LBE in the MEGAPIE Lower Liquid Metal Container (LLMC) accumulates radio-active substances which, in the event of a leak, must be cooled and contained under controlled conditions, as they may otherwise contaminate the facility. The FSLT experiment has been devised to fully test the structural integrity of the containment hull against a sudden liquid metal leak, and in addition, to resolve the peak temperature of he coolant, to validate the sensors used in detecting a leak and of proof-test the analytical methods used in predicting the consequences of a leak. The FSLT experiment has been analysed ahead of the test, and both thermal and structural aspects calculated using commercial codes. The predictions applied conservative assumptions to the analysis of the thermal shock so as to preclude the likelihood of an unforeseen failure of the hull. In this document, these initial predictions are compared to the temperature and strain data recorded in the experiment. Further analysis, to be published at a later stage, will focus on applying actual conditions realised in the experiment, as opposed to the envelope case used in the test predictions. The integrity of the containment hull under loads resulting from liquid metal-leak is therefore the focal point of the experiment described in the current document, and serves as a key reference test for the Iicensing of the facility. The data recorded during the SLT experiment shows that the MEGAPIE containment hull is

  20. Spring 5 & reactive streams

    CERN Multimedia

    CERN. Geneva; Clozel, Brian

    2017-01-01

    Spring is a framework widely used by the world-wide Java community, and it is also extensively used at CERN. The accelerator control system is constituted of 10 million lines of Java code, spread across more than 1000 projects (jars) developed by 160 software engineers. Around half of this (all server-side Java code) is based on the Spring framework. Warning: the speakers will assume that people attending the seminar are familiar with Java and Spring’s basic concepts. Spring 5.0 and Spring Boot 2.0 updates (45 min) This talk will cover the big ticket items in the 5.0 release of Spring (including Kotlin support, @Nullable and JDK9) and provide an update on Spring Boot 2.0, which is scheduled for the end of the year. Reactive Spring (1h) Spring Framework 5.0 has been released - and it now supports reactive applications in the Spring ecosystem. During this presentation, we'll talk about the reactive foundations of Spring Framework with the Reactor project and the reactive streams specification. We'll al...

  1. Characterizing the Effective Bandwidth of Nonlinear Vibratory Energy Harvesters Possessing Multiple Stable Equilibria

    Science.gov (United States)

    Panyam Mohan Ram, Meghashyam

    In the last few years, advances in micro-fabrication technologies have lead to the development of low-power electronic devices spanning critical fields related to sensing, data transmission, and medical implants. Unfortunately, effective utilization of these devices is currently hindered by their reliance on batteries. In many of these applications, batteries may not be a viable choice as they have a fixed storage capacity and need to be constantly replaced or recharged. In light of such challenges, several novel concepts for micro-power generation have been recently introduced to harness, otherwise, wasted ambient energy from the environment and maintain these low-power devices. Vibratory energy harvesting is one such concept which has received significant attention in recent years. While linear vibratory energy harvesters have been well studied in the literature and their performance metrics have been established, recent research has focused on deliberate introduction of stiffness nonlinearities into the design of these devices. It has been shown that, nonlinear energy harvesters have a wider steady-state frequency bandwidth as compared to their linear counterparts, leading to the premise that they can used to improve performance, and decrease sensitivity to variations in the design and excitation parameters. This dissertation aims to investigate this premise by developing an analytical framework to study the influence of stiffness nonlinearities on the performance and effective bandwidth of nonlinear vibratory energy harvesters. To achieve this goal, the dissertation is divided into three parts. The first part investigates the performance of bi-stable energy harvesters possessing a symmetric quartic potential energy function under harmonic excitations and carries out a detailed analysis to define their effective frequency bandwidth. The second part investigates the relative performance of mono- and bi-stable energy harvesters under optimal electric loading

  2. 46 CFR 176.620 - Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Description of the Alternative Hull Examination (AHE... Hull and Tailshaft Examinations § 176.620 Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels. The Alternative Hull Examination (AHE) Program provides you with an...

  3. 46 CFR 176.625 - Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain passenger...

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Eligibility requirements for the Alternative Hull... CERTIFICATION Hull and Tailshaft Examinations § 176.625 Eligibility requirements for the Alternative Hull... if— (1) It is constructed of steel or aluminum; (2) It has an effective hull protection system; (3...

  4. Measurement of dose rate and estimation of beta activity in zircaloy hull drum

    International Nuclear Information System (INIS)

    Pandey, J.P.N.; Kumar, Pankaj; Shinde, A.M.; Purohit, R.G.; Sarkar, P.K.

    2012-01-01

    Fuel Reprocessing Plant is designed for the processing of spent fuel from reactor for the recovery of plutonium and uranium as PuO 2 and U 3 O 8 respectively. Zircaloy is used as cladding material of natural uranium fuel pins used in the reactors. In reprocessing plants chop and leach method is used to remove the zircaloy clad from the fuel matrix during Head End Treatment. Initially spent fuel bundles are chopped into pieces and collected in perforated baskets kept in dissolvers. All chopped pieces are dissolved in HNO 3 in the dissolvers followed by heating and boiling. Dissolved solutions are transferred to Filtrate Tank (FT) leaving behind un-dissolved zircoloy hull pieces in the dissolver baskets. Un-dissolved and almost dry hull pieces are transferred in hull drum from the dissolver baskets using the Hull Tilting Facility. Hull drums are made of stainless steel having 500 litre capacity and two third of its volume is filled with zircoloy pieces. Hull drums filled with hull pieces are loaded in Hull Removal Cask (HRC) and transported to SWMF (Solid Waste Management Facility) site for interim storage/disposal in tile holes. Hull pieces are high active solid wastes which contain significant amount of fission products. Radiation levels on hull drums are in the range of few hundreds of mGy/h which has high potential of external hazards if not handled properly. Therefore hull drums are handled remotely in specially designed lead shielded cask

  5. Characteristics of plutonium, curium and uranium in hulls of FUGEN MOX spent fuel by destructive analysis

    International Nuclear Information System (INIS)

    Iijima, Shizuka; Goto, Yuichi; Samoto, Hirotaka; Shichi, Ryo; Shimizu, Takenori

    2011-01-01

    We have been developing a non-destructive assay system called hulls monitor for nuclear fuel materials retained in hulls at the Tokai Reprocessing Plant (TRP). The hulls monitor is based on a passive neutron measurement method, so its applicability should be evaluated by a destructive analysis of hulls that are recovered from the reprocessing process. In this study, hulls came from the Advanced Thermal Reactor (ATR) FUGEN were taken from the dissolution process of TRP and destructively analyzed. Two kinds of hulls from ATR-MOX spent fuel assemblies and from ATR-UO 2 spent fuel assemblies were taken and soaked with nitric acid then fused with ammonium hydrogen sulfate, followed by Pu, 244 Cm, U mass determination by alpha spectrometry and ICP-AES. The characteristics of hulls came from MOX spent fuel assemblies were revealed by comparison of ATR-MOX spent fuel with ATR-UO 2 spent fuel. (author)

  6. Analysis of rabbit intervertebral disc physiology based on water metabolism. II. Changes in normal intervertebral discs under axial vibratory load

    International Nuclear Information System (INIS)

    Hirano, N.; Tsuji, H.; Ohshima, H.; Kitano, S.; Itoh, T.; Sano, A.

    1988-01-01

    Metabolic changes induced by axial vibratory load to the spine were investigated based on water metabolism in normal intervertebral discs of rabbits with or without pentobarbital anesthesia. Tritiated water concentration in the intervertebral discs of unanesthetized rabbits was reduced remarkably by axial vibration for 30 minutes using the vibration machine developed for this study. Repeated vibratory load for 18 and 42 hours duration showed the recovery of 3 H 2 O concentration of the intervertebral disc without anesthesia. Computer simulation suggested a reduction of blood flow surrounding the intervertebral disc following the vibration stress. However, no reduction of the 3 H 2 O concentration in the intervertebral disc was noted under anesthesia. Emotional stress cannot be excluded as a factor in water metabolism in the intervertebral disc

  7. SAVIT: a dymanic model to predict vibratory motion within a spent fuel shipping cask; rail car system

    International Nuclear Information System (INIS)

    Fields, S.R.

    1978-03-01

    A dynamic model of a spent fuel shipping cask-rail car system has been developed to provide estimates of the vibratory motion of LWR spent fuel assemblies during transport and to estimate the effects of this motion on the condition of the assemblies when they arrive at receiving and storage facilities. Results of preliminary test computations are presented to illustrate the capabilities of the model

  8. Psychomotor Battery Approaches to Performance Prediction and Evaluation in Hyperbaric, Thermal and Vibratory Environments: Annotated Bibliographies and Integrative Review

    Science.gov (United States)

    1980-10-01

    W77-Mar78 and Vibratory Environments: Annotated Biblia - 4.-EFRIGOO EOT*_1 graphies and Integrative Review. I. CONTRACT OR GRANT NUMSER(a) David J...Papers In the third phase of the effort, the final version of the three speciai-environrneni performance battery bibliographies was corriiled and the...performance at much lower pressu. (e.g. 3 to 4 ATA when nitrogen is involved). The following sections will integrate the available liter - ature on the effects

  9. Development on the automatic separator of separation of residual powders from SF hulls

    International Nuclear Information System (INIS)

    Jung, Jae Hoo; Kim, Young Hwang; Kim, Ki Ho; Park, Byung Buk; Lee, Hyo Jik; Kim, Sung Hyun; Park, Hee Sung; Lee, Jong Kwang; Kim, Ho Dong

    2009-12-01

    At the previous process of auto hull separator, vol-oxidizer convert UO 2 pellets to U 3 O 8 powder, and in the next step, hulls and powders is collected into each part of two vessels. In order to enhance the recover rate, fine powders on the surface of hulls should be removed from hulls. Auto hulls separator for fine powders is a device which can separate fine powders from hulls. In order to design and manufacture this device, we analyzed fine powders which are remained on the surface of hulls for separation properties, and selected separation and operation methods. Also, the main mechanism is devised by using the design considerations. These main mechanism consists of rotation drum, parts feeder, hull conveyer, powders separator, air shower, and vessels. Design considerations for auto hulls separator as follows ; capacity : 100 kg HM/batch, rod-cut length : 50 mm, recovery rate for fine powders : 95 % and operation condition : over 12 hrs/batch. We considered connection methods of the vessel and high vacuum module which can join with the outlet of auto hulls separator. Also, by using the above results, we have manufactured auto hulls separator for fine powders, and conducted blank tests for operation condition. Here, hulls of 50 mm length for test are used with 20 kg HM/batch. We have conducted separation tests of 2 batches to collect fine powders with hulls of 10 kg HM/batch. Our goal of recovery rate was 95%, but in the test result, the recovery rate of fine powders on the surface of hulls was over 96 %

  10. Spring integration essentials

    CERN Document Server

    Pandey, Chandan

    2015-01-01

    This book is intended for developers who are either already involved with enterprise integration or planning to venture into the domain. Basic knowledge of Java and Spring is expected. For newer users, this book can be used to understand an integration scenario, what the challenges are, and how Spring Integration can be used to solve it. Prior experience of Spring Integration is not expected as this book will walk you through all the code examples.

  11. Vibratory response of a mirror support/positioning system for the Advanced Photon Source project at Argonne National Laboratory

    International Nuclear Information System (INIS)

    Basdogan, I.; Shu, Deming; Kuzay, T.M.; Royston, T.J.; Shabana, A.A.

    1996-01-01

    The vibratory response of a typical mirror support/positioning system used at the experimental station of the Advanced Photon Source (APS) project at Argonne National Laboratory is investigated. Positioning precision and stability are especially critical when the supported mirror directs a high-intensity beam aimed at a distant target. Stability may be compromised by low level, low frequency seismic and facility-originated vibrations traveling through the ground and/or vibrations caused by flow-structure interactions in the mirror cooling system. The example case system has five positioning degrees of freedom through the use of precision actuators and rotary and linear bearings. These linkage devices result in complex, multi-dimensional vibratory behavior that is a function of the range of positioning configurations. A rigorous multibody dynamical approach is used for the development of the system equations. Initial results of the study, including estimates of natural frequencies and mode shapes, as well as limited parametric design studies, are presented. While the results reported here are for a particular system, the developed vibratory analysis approach is applicable to the wide range of high-precision optical positioning systems encountered at the APS and at other comparable facilities

  12. Pro Spring Integration

    CERN Document Server

    Lui, M; Chan, Andy; Long, Josh

    2011-01-01

    Pro Spring Integration is an authoritative book from the experts that guides you through the vast world of enterprise application integration (EAI) and application of the Spring Integration framework towards solving integration problems. The book is:. * An introduction to the concepts of enterprise application integration * A reference on building event-driven applications using Spring Integration * A guide to solving common integration problems using Spring Integration What makes this book unique is its coverage of contemporary technologies and real-world information, with a focus on common p

  13. Coil spring venting arrangement

    International Nuclear Information System (INIS)

    McCugh, R.M.

    1975-01-01

    A simple venting device for trapped gas pockets in hydraulic systems is inserted through a small access passages, operated remotely, and removed completely. The device comprises a small diameter, closely wound coil spring which is pushed through a guide temporarily inserted in the access passage. The guide has a central passageway which directs the coil spring radially upward into the pocket, so that, with the guide properly positioned for depth and properly oriented, the coil spring can be pushed up into the top of the pocket to vent it. By positioning a seal around the free end of the guide, the spring and guide are removed and the passage is sealed

  14. The diagnostic role of high-speed vocal fold vibratory imaging.

    Science.gov (United States)

    Mendelsohn, Abie H; Remacle, Marc; Courey, Mark S; Gerhard, Friedrich; Postma, Gregory N

    2013-09-01

    Although high-speed imaging (HSI) has been identified as a valuable tool in phonatory biomechanics research, to date, there have only been a selected number of reports investigating the clinical utility of HSI. We aim to elucidate the role of HSI in the diagnosis of the dysphonic patient. The video files from 28 consecutive dysphonic patients with concurrently acquired videostroboscopy and HSI were retrospectively collected. Stroboscopy video files were edited to include vibratory motion only. Videos were then anonymously and randomly presented to four academic laryngologists. Experts were asked to assign a single best diagnosis for each video file. Assigned diagnoses were then compared with treatment diagnoses conferred based on medical history, phonatory evaluation, laryngeal examination, and response to treatment. Interrater analysis for the four laryngologists demonstrated significant and meaningful correlations for the diagnoses of polyps, cysts, nodules, and normal examination using stroboscopy (kappa > 0.40, P 0.40, P diagnostic accuracy above stroboscopy alone. Although specific laryngeal states such as presbyphonia may be better diagnosed with HSI, further studies are required to define HSI's precise role in the clinical setting. Copyright © 2013 The Voice Foundation. All rights reserved.

  15. Vibratory Machining Effect on the Properties of the Aaluminum Alloys Surface

    Directory of Open Access Journals (Sweden)

    Bańkowski D.

    2017-12-01

    Full Text Available The article presents an example of finishing treatment for aluminum alloys with the use of vibration machining, with loose abrasive media in a closed tumbler. For the analysis of selected properties of the surface layer prepared flat samples of aluminum alloy PA6/2017 in the state after recrystallization. The samples in the first stage were subjected to a treatment of deburring using ceramic media. In a second step polishing process performed with a strengthening metal media. In addition, for comparative purposes was considered. only the case of metal polishing. The prepared samples were subjected to hardness tests and a tangential tensile test. As a result of finishing with vibratory machining, it was possible to remove burrs, flash, rounding sharp edges, smoothing and lightening the surface of objects made. The basic parameters of the surface geometry were obtained using the Talysurf CCI Lite - Taylor Hobson optical profiler. As a result of the tests it can be stated that the greatest reduction of surface roughness and mass loss occurs in the first minutes of the process. Mechanical tests have shown that the most advantageous high values of tensile strength and hardness are obtained with two-stage vibration treatment, - combination of deburring and polishing. Moreover the use of metal media resulted in the strengthening of the surface by pressure deburring with metal media.

  16. Segmentation of turbo generator and reactor coolant pump vibratory patterns: a syntactic pattern recognition approach

    International Nuclear Information System (INIS)

    Tira, Z.

    1993-02-01

    This study was undertaken in the context of turbogenerator and reactor coolant pump vibration surveillance. Vibration meters are used to monitor equipment condition. An anomaly will modify the signal mean. At the present time, the expert system DIVA, developed to automate diagnosis, requests the operator to identify the nature of the pattern change thus indicated. In order to minimize operator intervention, we have to automate on the one hand classification and on the other hand, detection and segmentation of the patterns. The purpose of this study is to develop a new automatic system for the segmentation and classification of signals. The segmentation is based on syntactic pattern recognition. For the classification, a decision tree is used. The signals to process are the rms values of the vibrations measured on rotating machines. These signals are randomly sampled. All processing is automatic and no a priori statistical knowledge on the signals is required. The segmentation performances are assessed by tests on vibratory signals. (author). 31 figs

  17. A high-efficiency self-powered wireless sensor node for monitoring concerning vibratory events

    Science.gov (United States)

    Xu, Dacheng; Li, Suiqiong; Li, Mengyang; Xie, Danpeng; Dong, Chuan; Li, Xinxin

    2017-09-01

    This paper presents a self-powered wireless alarming sensor node (SWASN), which was designed to monitor the occurrence of concerning vibratory events. The major components of the sensor node include a vibration-threshold-triggered energy harvester (VTTEH) that powers the sensor node, a dual threshold voltage control circuit (DTVCC) for power management and a radio frequency (RF) signal transmitting module. The VTTEH generates significant electric energy only when the input vibration reaches certain amplitude. Thus, the VTTEH serves as both the power source and the vibration-event-sensing element for the sensor node. The DTVCC was specifically designed to utilize the limited power supply from the VTTEH to operate the sensor node. Constructed with only voltage detectors and MOSFETs, the DTVCC achieved low power consumption, which was 65% lower compared with the power management circuit designed in our previous work. Meanwhile, a RF transmit circuit was constructed based on the commercially available CC1110-F32 wireless transceiver chip and a compact planar antenna was designed to improve the signal transmission distance. The sensor node was fabricated and was characterized both in the laboratory and in the field. Experimental results showed that the SWASN could automatically send out alarming signals when the simulated concerning event occurred. The waiting time between two consecutive transmission periods is less than 125 s and the transmission distance can reach 1.31 km. The SWASN will have broad applications in field surveillances.

  18. Two Novel Measurements for the Drive-Mode Resonant Frequency of a Micromachined Vibratory Gyroscope

    Directory of Open Access Journals (Sweden)

    Ancheng Wang

    2013-11-01

    Full Text Available To investigate the drive-mode resonance frequency of a micromachined vibratory gyroscope (MVG, one needs to measure it accurately and efficiently. The conventional approach to measure the resonant frequency is by performing a sweep frequency test and spectrum analysis. The method is time-consuming and inconvenient because of the requirements of many test points, a lot of data storage and off-line analyses. In this paper, we propose two novel measurement methods, the search method and track method, respectively. The former is based on the magnitude-frequency characteristics of the drive mode, utilizing a one-dimensional search technique. The latter is based on the phase-frequency characteristics, applying a feedback control loop. Their performances in precision, noise resistivity and efficiency are analyzed through detailed simulations. A test system is implemented based on a field programmable gate array (FPGA and experiments are carried out. By comparing with the common approach, feasibility and superiorities of the proposed methods are validated. In particular, significant efficiency improvements are achieved whereby the conventional frequency method consumes nearly 5,000 s to finish a measurement, while only 5 s is needed for the track method and 1 s for the search method.

  19. Preduction of the vibratory behaviour of a multistage gaseous diffusion plant

    International Nuclear Information System (INIS)

    Descleve, P.; Bertaut, C.; Briot, P.

    1979-01-01

    A study has been made to predict the vibratory behaviour of the rotating machinery of a gaseous diffusion plant starting from the results obtained for a single machine. TRICASTIN gaseous diffusion plant uses several hundred of enrichment stages but only three different sizes of machine are used. Each individual machine is a vertical assembly of a compressor heat exchanger and diffusion barriers, this column is supported on four lugs on a concrete slab. This slab must accomodate thermal expansion and is placed on neoprene pads. Due to the compactness of the system the mass of concrete is relatively small. Typically the mass of a machine of the intermediate size is 84 T, the mass of associated concrete is 55 T. Furthermore this supporting slab is flexible, meaning that a dynamic analysis of the slab shows several frequencies below the compressor rotational speed. Extensive dynamic tests have been conducted on a machine supported on a rigid foundation. These tests have shown that the main source of mechanical excitation was caused at 50 Hz by the unbalance of the electrical motor rotor. Then the problem remained to predict the behaviour of a group of twenty machines in the plant itself. (orig.)

  20. Mockito for Spring

    CERN Document Server

    Acharya, Sujoy

    2015-01-01

    If you are an application developer with some experience in software testing and want to learn more about testing frameworks, then this technology and book is for you. Mockito for Spring will be perfect as your next step towards becoming a competent software tester with Spring and Mockito.

  1. Characterization of spent fuel hulls and dissolution residues

    International Nuclear Information System (INIS)

    Gue, J.P.; Andriessen, H.

    1985-04-01

    The main results obtained within the framework of CEC programmes, by KFK, UKAEA and CEA, are reviewed concerning the characterization of dissolution wastes. The contents were determined of the main radioactive emitters contained in the hulls originating in a whole fuel assembly sampled at the La Hague plant, or from Dounreay PFR fuels. Radiochemical characterizations were carried out by different methods including neutron emission measurement, alpha and beta-gamma spectrometry, and mass spectrometry. Decontamination of the hulls by using rinsings and supplementary treatment were also dealt with. The ignition and explosion risks associated with the zircaloy fines formed during the shearing of LWR fuels were examined, and the ignition properties of irradiated and unirradiated zircaloy powders were determined and compared. The physical properties and compositions of the dissolution residues of PFR fuels were defined, in order to conduct tests on the immobilization of these wastes in cement

  2. Cold-crucible melting of hulls and structural materials

    International Nuclear Information System (INIS)

    Jouan, A.; Jacquet-Francillon, N.; Puyou, M.; Piccinato, R.

    1990-01-01

    The method currently implemented at the La Hague UP3 reprocessing plant for conditioning of PWR zircaloy hulls is cement embedding. Another promising method, mainly for reducing the waste volume and the available exchange surface area, is melting. A cold-crucible melting process has therefore been developed by the CEA at Marcoule (France) over the last decade. Development work first concentrated on cladding hulls from fast breeder reactors, then from pressurized water reactors. The process can be used for both types of cladding wastes. Subassembly head and foot end-caps are sheared off and should be suitable for surface storage after α decontamination by successive rinsing. If necessary because of their α activity, they could be melted in a larger furnace

  3. Biofouling and Design of a Biomimetic Hull-Grooming Tool

    Science.gov (United States)

    2007-09-14

    have barred the use of organotin compounds such as tributyltin ( TBT ) and copper-based paints, which are currently used by the Navy and have become...copper into the water, killing the fouling organisms. There is new research in biomimetic polymers that deter fouling, but are non- toxic . These polymers...is new research in biomimetic polymers that deter fouling, but are non- toxic . These polymers are rigidly attached to the hull surface extending

  4. Hulls and structural material waste conditioning by high pressure compaction

    International Nuclear Information System (INIS)

    Frotscher, H.

    1991-01-01

    Since 1986 KfK is developing a conditioning process. Main subjects of the investigations were the development of the production technique and the planning of the most important equipments of the process under remote conditions. The process is based on an extensive program of experiments. Inactive bulks of hulls and structural material components were compacted using maximum axial pressure load of about 300 MPa. The product density as function of press force was experimentally determinated. The mechanical loads of the press and tools were estimated for the design of these equipments. The hydraulic press consists a horizontal four-cylinder press. The maximum force of the press is 25 MN. The main advantage is the modular design of the press which is open on all sides. Especially the free accessibility from top is ensured. The report also represents relevant radiological data of the alternative product. Co-60 is the dominating activity of the product due to the effects of the heat production. An amount of 10 kg hull waste or 25 kg top and bottom pieces of the spent fuel assemblies per package is already beyond the Co-60 limit of the KONRAD regulations. The nuclear thermal power of a filled container is approximately sixty times lower compared with a vitrified HLW-container. Since the product shows thermal stability beyond 200 0 C, this it is suited for a combined disposal together with vitrified HLW-containers in salt bore holes of a geological disposal. The preliminary cost evaluation is based on a reprocessing throughput of 500 t HM per year and volume reduction factor of 5.3. Accordingly there are produced 300 waste packages with hulls only or 625 units with hulls and top and bottom pieces which require 1.6 or 2.3 millions DM respectively

  5. Free-surface flow around an appended hull

    International Nuclear Information System (INIS)

    Lungu, A; Pacuraru, F

    2010-01-01

    The prediction of the total drag experienced by an advancing ship is a complicated problem which requires a thorough understanding of the hydrodynamic forces acting on the hull, the physical processes from which these forces arise as well as their mutual interaction. A general numerical method to predict the hydrodynamic performance of a twin-propeller combatant ship is presented in the paper, which describes the solution of a RANS solver coupled with a body force method as an attempt in investigating the flow features around the ship hull equipped with rotating propellers and rudders. A special focus is made on the propeller non-symmetrical inflow field, aimed at obtaining the necessary data for the propulsive performances evaluation as well as for the propeller final design. The reported work allows not only the performance evaluation for the overall performances of a hull, but also leads to the development, implementation and validation of new concepts in modeling the turbulent vortical flows, with direct connection to the ship propulsion problem.

  6. Treatment of stainless steels and zircaloy cladding hulls

    International Nuclear Information System (INIS)

    Jenkins, I.L.; Taylor, R.F.

    1978-01-01

    Results are reported on the fissile material content and the distribution of alpha and beta-gamma emitters in both types of cladding. Apart from very small amounts of residual fuel, fissile material is present as a deposit formed during the dissolution of fuel and also as material driven into the cladding by fission recoil. Alpha-emitters penetrate to depths of 1-2 μm into both S.S. and Zircaloy claddings. The surface deposits on individual hulls can be effectively removed by refluxing with nitric acid or by cleaning with nitric acid in an ultrasonic bath. The physical structural and handling behavior of hull assemblies are examined as being of key importance to the establishment of an efficient cleaning process. The reference leaching target is to extract residual fuel fragments and to remove surface deposits. Preferred routes for compaction, drumming, and encapsulation are briefly reviewed with regard to achieving a final package volume half that of the original hulls with associated hardware

  7. On the Influence of Hull Girder Flexibility on the Wave

    DEFF Research Database (Denmark)

    Seng, Sopheak; Andersen, Ingrid Marie Vincent; Jensen, Jørgen Juncher

    2012-01-01

    Numerical predictions and model test results of the wave induced bending moments in a 9,400 TEU post-Panamax container vessel are presented for two regular wave scenarios. Different numerical procedures have been applied: a linear and non-linear time-domain strip theory and a direct calculation (...... (CFD) solving the Navier-Stokes equations with the free surface captured by a volume-of-fluid (VOF) method. In all procedures the flexibility of the hull girder is modelled as a non-uniform Timoshenko beam. It is observed that the non-linear models agree well with the model tests...... and as there is no occurrence of severe slamming in the cases considered, the inexpensive non-linear strip theory is as accurate as the direct CFD calculation method. In a comparison with the results using the rigid body assumption, the increase in the vertical bending moment (VBM) amidships due to the flexibility of the hull...... girder is found to be approximately 7% (peak-to-peak amplitude) in general. The non-linear responses, however, contain over-harmonic frequencies which may coincide with the natural frequency of the two-node vertical bending mode inducing resonance. In that case the hull girder flexibility causes...

  8. Treatment of cladding hulls by the HIPOW process

    International Nuclear Information System (INIS)

    Larker, H.T.; Tegman, R.

    1981-01-01

    The conditions for densifying and bonding Zircaloy cladding hulls from spent LWR fuel to blocks by the HIPOW (hot isostatic pressing of waste) process have been studied. Fully dense and mechanically strong blocks of Zircaloy can be made without additives at temperatures around 1000 0 C. A volume reduction of about seven times and surface area reduction of more than 300 times, compared to typical loose-filled cladding hulls remaining after the chop-leach operations in a reprocessing plant, can be obtained. A study of a possible process for industrial scale has been made. Handling under water can prevent any fire hazard in the preparation sequence. The use of a special hermetically sealed double-wall metal container encasing the hulls during the densification in the hot isostatic press virtually eliminates the problem of lasting contamination of this equipment, thus greatly simplifying service and maintenance. One hot isostatic press can serve a reprocessing line with an LWR fuel capacity of 800 tons/year. Fines (residues) from fuel dissolution and alpha-contaminated ashes from incinerated organic materials in the plant may also be incorporated in the Zircaloy blocks. Tritium can quantitatively be contained in these blocks

  9. Flooding and schools: experiences in Hull in 2007.

    Science.gov (United States)

    Convery, Ian; Carroll, Bob; Balogh, Ruth

    2015-01-01

    Hull, a city in the East Riding of Yorkshire, United Kingdom, suffered severe flooding in June 2007, affecting some 8,600 households and most schools. Despite the potential for damage in such disasters, no studies of the effects of floods on teachers and schools in the UK appear to have been published previously. This study analysed the impacts of the floods on teachers in Hull in two stages: first through correspondence with Hull City Council and a mailed questionnaire to 91 head teachers of primary, secondary, and special schools; and second, through in-depth interviews with head teachers from six flooded schools, representing different degrees of flood experience, and a questionnaire completed by eight teachers from the same schools. The findings reveal the importance and the complexity of the role of the school in the wider community in a time of crisis. The study highlights issues concerning preparedness for floods, support for schools, and flood protection for schools. © 2014 The Author(s). Disasters © Overseas Development Institute, 2014.

  10. Fabrication of renewable biocomposites from soy hull and bioplastics

    Science.gov (United States)

    Nanda, Malaya Ranjan

    This is an investigation for fabrication of biocomposites from soy hull and bioplastics like polylactide (PLA) and polyhydroxy butyrate-co- valerate (PHBV). The study was divided into three parts; the first was the development of a suitable PHBV/PLA blend. The second part involved the fabrication of composites from soy hull and PHBV/PLA blend and its comparison with polypropylene (PP)/soy hull composites. The third part was the effect of compatibilizer on the performance of the composites. From tensile study, the elongation of an optimized blend was found to be improved by 148 and 250% over the virgin polymers PHBV and PLA respectively. Scanning electron microscope revealed a stronger fiber-matrix interaction in PHBV/PLA composites over PP composites. Furthermore, the compatibilizer improved the impact and flexural strength by 56 and 32% respectively over the un-compatibilized counterpart; more significantly the resulting compatibilized composites showed improved hydrophobicity by more than 22% over un-compatibilized counterpart.

  11. Effect of stern hull shape on turning circle of ships

    Science.gov (United States)

    Jaswar, Maimun, A.; Wahid, M. A.; Priyanto, A.; Zamani, Pauzi, Saman

    2012-06-01

    Many factors such as: stern hull shape, length, draught, trim, propulsion system and external forces affecting the drift angle influence rate of turn and size of turning circle of ships. This paper discusses turning circle characteristics of U and V stern hull shape of Very Large Crude Oil Carrier (VLCC) ships. The ships have same principal dimension such as length, beam, and draught. The turning circle characteristics of the VLCC ships are simulated at 35 degree of rudder angle. In the analysis, firstly, turning circle performance of U-type VLCC ship is simulated. In the simulation, initial ship speed is determined using given power and rpm. Hydrodynamic derivatives coefficients are determined by including effect of fullness of aft run. Using the obtained, speed and hydrodynamic coefficients, force and moment acting on hull, force and moment induced by propeller, force and moment induced by rudder are determined. Finally, ship trajectory, ratio of speed, yaw angle and drift angle are determined. Results of simulation results of the VLCC ship are compared with the experimental one as validation. Using the same method, V-type VLCC is simulated and the simulation results are compared with U-type VLCC ship. Results shows the turning circle of U-type is larger than V-type due to effect stern hul results of simulation are.

  12. Angular circulation speed of tablets in a vibratory tablet coating pan.

    Science.gov (United States)

    Kumar, Rahul; Wassgren, Carl

    2013-03-01

    In this work, a single tablet model and a discrete element method (DEM) computer simulation are developed to obtain the angular circulation speed of tablets in a vibratory tablet coating pan for range of vibration frequencies and amplitudes. The models identify three important dimensionless parameters that influence the speed of the tablets: the dimensionless amplitude ratio (a/R), the Froude number (aω2/g), and the tablet-wall friction coefficient, where a is the peak vibration amplitude at the drum center, ω is the vibration angular frequency, R is the drum radius, and g is the acceleration due to gravity. The models predict that the angular circulation speed of tablets increases with an increase in each of these parameters. The rate of increase in the angular circulation speed is observed to decrease for larger values of a/R. The angular circulation speed reaches an asymptote beyond a tablet-wall friction coefficient value of about 0.4. Furthermore, it is found that the Froude number should be greater than one for the tablets to start circulating. The angular circulation speed increases as Froude number increases but then does not change significantly at larger values of the Froude number. Period doubling, where the motion of the bed is repeated every two cycles, occurs at a Froude number larger than five. The single tablet model, although much simpler than the DEM model, is able to predict the maximum circulation speed (the limiting case for a large value of tablet-wall friction coefficient) as well as the transition to period doubling.

  13. Alternate rhythmic vibratory stimulation of trunk muscles affects walking cadence and velocity in Parkinson's disease.

    Science.gov (United States)

    De Nunzio, Alessandro M; Grasso, Margherita; Nardone, Antonio; Godi, Marco; Schieppati, Marco

    2010-02-01

    During the administration of timed bilateral alternate vibration to homonymous leg or trunk muscles during quiet upright stance, Parkinsonian (PD) patients undergo cyclic antero-posterior and medio-lateral transfers of the centre of foot pressure. This event might be potentially exploited for improving gait in these patients. Here, we tested this hypothesis by applying alternate muscle vibration during walking in PD. Fifteen patients and 15 healthy subjects walked on an instrumented walkway under four conditions: no vibration (no-Vib), and vibration of tibialis anterior (TA-Vib), soleus (Sol-Vib) and erector spinae (ES-Vib) muscles of both sides. Trains of vibration (internal frequency 100 Hz) were delivered to right and left side at alternating frequency of 10% above preferred step cadence. During vibration, stride length, cadence and velocity increased in both patients and healthy subjects, significantly so for ES-Vib. Stance and swing time tended to decrease. Width of support base increased with Sol-Vib or TA-Vib, but was unaffected by ES-Vib. Alternate ES vibration enhances gait velocity in PD. The stronger effect of ES over leg muscle vibration might depend on the relevance of the proprioceptive inflow from the trunk muscles and on the absence of adverse effects on the support base width. Trunk control is defective in PD. The effect of timed vibratory stimulation on gait suggests the potential use of trunk proprioceptive stimulation for tuning the central pattern generators for locomotion in PD. Copyright (c) 2009 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.

  14. Vibratory shear enhanced membrane process and its application in starch wastewater recycle

    Directory of Open Access Journals (Sweden)

    Kazi Sarwar Hasan

    2002-11-01

    Full Text Available Membrane application in wastewater is gaining significant popularity. Selecting the right membrane and filtration technique is an important consideration to ensure a successful system development and long term performance. A new type of membrane filtration technology known as ‘Vibratory Shear Enhanced Process’ (VSEP is introduced in this paper with some test results that has been conducted with VSEP pilot unit to recycle starch wastewater. Conventional cross flow membrane process used in wastewater application always led to rapid fouling. This loss in throughput capacity is primarily due to the formation of a layer that builds up naturally on the membranes surface during the filtration process. In addition to cutting down on the flux performance of the membrane, this boundary or gel layer acts as a secondary membrane reducing the native design selectivity of the membrane in use. This inability to handle the buildup of solids has also limited the use of membranes to low-solids feed streams. In a VSEP system, an additional shear wave produced by the membrane’s vibration cause solids and foulants to be lifted off the membrane surface and remixed with the bulk material flowing through the membrane stack. This high shear processing exposes the membrane pores for maximum throughput that is typically between 3 to10 times the throughput of conventional cross-flow systems. The short term results with raw starch wastewater shows very stable flux rate of 110 lmh using the VSEP system and selecting the PVDF ultrafiltration membrane with no pre-filtration.

  15. The Effect of Material and Side Walls on Hull Deflection during a Blast Event

    Science.gov (United States)

    2017-12-13

    ARL-CR-0822 ● DEC 2017 US Army Research Laboratory The Effect of Material and Side Walls on Hull Deflection during a Blast Event...Army Research Laboratory The Effect of Material and Side Walls on Hull Deflection during a Blast Event prepared by Danielle Abell SURVICE...Walls on Hull Deflection during a Blast Event 5a. CONTRACT NUMBER W911QX-16-D-0014 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S

  16. Calculation of Flows Over Underwater Bodies with Hull, Sail and Appendages

    International Nuclear Information System (INIS)

    Shoab, M.; Ayub, M.; Bilal, S.; Zahir, S.; Khan, M.A.

    2004-01-01

    A comprehensive study has been made for the hydrodynamic analysis of the submarine DARPA 2. The analysis was first performed for hull, then hull with sail on top and then for the complete submarine including hull, sail and appendages. A comparison of tangential velocity and pressure distribution for hull is accomplished using CFD flow solvers and published data. Further, the pressure distribution over the hull with sail is also analyzed. Finally, pressure distribution, forces and moments were calculated over the complete submarine including hull, sail and appendages. Comparison 01 pressure distribution and tangential velocity for the hull show a good agreement with published data. Pressure coefficient comparison for the hull with sail shows the good CFD-CFD agreement. Comparison of Normal force and pitching moment of complete submarine having hull, sail and appendages shows a reasonable agreement with the experimental results of DARPA 2. Both quantitative and qualitative analysis of the complete submarine estimates the required design force and moment at different angles of attack and also demonstrate the flow visualization. (author)

  17. Grounding-Induced Sectional Forces and Residual Strength of Grounded Ship Hulls

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Pedersen, Preben Terndrup

    1996-01-01

    The aim of the present study is to determine the sectional forces induced by ship grounding and also to assess the residual strength of groundedship hulls. An analytical approach is used to estimate the grounding-induced sectional forces of ships. The extent and location of structural damage due...... to grounding is defined based on the ABS Safe Hull guide. The residual strength of damaged hulls is calculated by using a simple analytical formula. The method is applied to residual strength assessment of a damaged double hull tanker of 38,400 dwt due to grounding....

  18. CFD investigation of pentamaran ship model with chine hull form on the resistance characteristics

    Science.gov (United States)

    Yanuar; Sulistyawati, W.

    2018-03-01

    This paper presents an investigation of pentamaran hull form with chine hull form to the effects of outriggers position, asymmetry, and deadrise angles on the resistance characteristics. The investigation to the resistance characteristics by modelling pentamaran hull form using chine with symmetrical main hull and asymmetric outboard on the variation deadrise angles: 25°, 30°, 35° and Froude number 0,1 to 0,7. On calm water resistance characteristics of six pentamaran models with chine-hull form examined by variation of deadrise angles by using CFD. Comparation with Wigley hull form, the maximum resistance drag reduction of the chine hull form was reduced by 15.81% on deadrise 25°, 13.8% on deadrise 30°, and 20.38% on deadrise 35°. While the smallest value of total resistance coefficient was generated from chine 35° at R/L:1/14 and R/L:1/7. Optimum hull form for minimum resistance has been obtained, so it is interesting to continue with angle of entrance and stem angle of hull for further research.

  19. Genetic control of a transition from black to straw-white seed hull in rice domestication.

    Science.gov (United States)

    Zhu, Bo-Feng; Si, Lizhen; Wang, Zixuan; Zhou, Yan; Zhu, Jinjie; Shangguan, Yingying; Lu, Danfeng; Fan, Danlin; Li, Canyang; Lin, Hongxuan; Qian, Qian; Sang, Tao; Zhou, Bo; Minobe, Yuzo; Han, Bin

    2011-03-01

    The genetic mechanism involved in a transition from the black-colored seed hull of the ancestral wild rice (Oryza rufipogon and Oryza nivara) to the straw-white seed hull of cultivated rice (Oryza sativa) during grain ripening remains unknown. We report that the black hull of O. rufipogon was controlled by the Black hull4 (Bh4) gene, which was fine-mapped to an 8.8-kb region on rice chromosome 4 using a cross between O. rufipogon W1943 (black hull) and O. sativa indica cv Guangluai 4 (straw-white hull). Bh4 encodes an amino acid transporter. A 22-bp deletion within exon 3 of the bh4 variant disrupted the Bh4 function, leading to the straw-white hull in cultivated rice. Transgenic study indicated that Bh4 could restore the black pigment on hulls in cv Guangluai 4 and Kasalath. Bh4 sequence alignment of all taxa with the outgroup Oryza barthii showed that the wild rice maintained comparable levels of nucleotide diversity that were about 70 times higher than those in the cultivated rice. The results from the maximum likelihood Hudson-Kreitman-Aguade test suggested that the significant reduction in nucleotide diversity in rice cultivars could be caused by artificial selection. We propose that the straw-white hull was selected as an important visual phenotype of nonshattered grains during rice domestication.

  20. Decontamination of fast reactor hulls and properties of immobilised waste forms

    International Nuclear Information System (INIS)

    Biddle, P.; Brown, P.E.; Rees, J.H.

    1986-01-01

    The studies described in this Report have been carried out on five batches of stainless steel hulls resulting from the reprocessing of fuel from the Prototype Fast Reactor at Dounreay. Direct immobilisation in cement and decontamination have been examined as possible routes for treating the hulls. A number of low temperature chemical techniques have been used to remove actinides and fission products from the hulls. The levels of α-activity could be reduced to less than 0.3 Ci/te of hulls. Thus decontamination might permit cheaper disposal than would be the case for undecontaminated hulls. 10mm sections of hulls have been immobilised in two cements in which either sand or blast furnace slag was used to extend the ordinary Portland cement. The level of Cs-137 leached from hulls immobilised in either of the cement compositions was about an order of magnitude lower than that leached from the bare hulls. For Sr-90, the BFS/OPC matrix gave a tenfold better retention than the sand/OPC. Ru-106 and Sb-125 were leached from the sand/OPC but not from the BFS/OPC samples. The preliminary studies suggested that cement was a satisfactory matrix for immobilising hulls and that the BFS/OPC was the better formulation. 30 refs, 26 tabs, 23 figs

  1. Learning Spring application development

    CERN Document Server

    Soni, Ravi Kant

    2015-01-01

    This book is intended for those who are interested in learning the core features of the Spring Framework. Prior knowledge of Java programming and web development concepts with basic XML knowledge is expected.

  2. Cyanobacteria in ambient springs

    Czech Academy of Sciences Publication Activity Database

    Cantonati, M.; Komárek, Jiří; Montejano, G.

    2015-01-01

    Roč. 24, č. 4 (2015), s. 865-888 ISSN 0960-3115 Institutional support: RVO:67985939 Keywords : Springs * Cyanoprokaryotes * Radiation * Nitrogen Subject RIV: EF - Botanics Impact factor: 2.258, year: 2015

  3. Spring Bottom Trawl Survey

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The standardized NEFSC Spring Bottom Trawl Survey was initiated in 1968 and covered an area from Cape Hatteras, NC, to Nova Scotia, Canada, at depths >27m....

  4. Masters of the springs

    DEFF Research Database (Denmark)

    Laursen, Steffen

    2010-01-01

    flanked by villages that relied on these water recourses for agricultural production. The springs emerged in the zone separating the cemeteries from the settlements. The freshwater springs were actively incorporated into the religious landscape of the dead, by consistently erecting mounds of a particular...... for water - a process which perhaps also is evidenced by temple constructions at Barbar, Umm al-Sujur and Abu Zaydan....

  5. Static-transmission-error vibratory-excitation contributions from plastically deformed gear teeth caused by tooth bending-fatigue damage

    Science.gov (United States)

    Mark, W. D.; Reagor, C. P.

    2007-02-01

    To assess gear health and detect gear-tooth damage, the vibratory response from meshing gear-pair excitations is commonly monitored by accelerometers. In an earlier paper, strong evidence was presented suggesting that, in the case of tooth bending-fatigue damage, the principal source of detectable damage is whole-tooth plastic deformation; i.e. yielding, rather than changes in tooth stiffness caused by tooth-root cracks. Such plastic deformations are geometric deviation contributions to the "static-transmission-error" (STE) vibratory excitation caused by meshing gear pairs. The STE contributions caused by two likely occurring forms of such plastic deformations on a single tooth are derived, and displayed in the time domain as a function of involute "roll distance." Example calculations are provided for transverse contact ratios of Qt=1.4 and 1.8, for spur gears and for helical-gear axial contact ratios ranging from Qa=1.2 to Qa=3.6. Low-pass- and band-pass-filtered versions of these same STE contributions also are computed and displayed in the time domain. Several calculations, consisting of superposition of the computed STE tooth-meshing fundamental harmonic contribution and the band-pass STE contribution caused by a plastically deformed tooth, exhibit the amplitude and frequency or phase modulation character commonly observed in accelerometer-response waveforms caused by damaged teeth. General formulas are provided that enable computation of these STE vibratory-excitation contributions for any form of plastic deformation on any number of teeth for spur and helical gears with any contact ratios.

  6. Implementation of the resonant vibratory feeders control algorithm on Simatic S7-1200 from MATLAB Simulink enviroment

    Directory of Open Access Journals (Sweden)

    Mitrović Radomir B.

    2016-01-01

    Full Text Available Simulink is an important tool for modeling and simulation of process and control algorithms. It's expansion, PLC Coder, enables direct conversion of model subsystem into SCL, structured text code, which is then used by PLC IDE to create function blocks. This shortens developing time of algorithms for PLC controller. Also, this reduces possibility for a coding error. This paper describes Simulink PLC Coder and workflow for developing PID control algorithm for Siemens Simatic S7-1200 PLC. Control object used here is resonant vibratory feeder having electromagnetic drive.

  7. A study on the contribution of body vibrations to the vibratory sensation induced by high-level, complex low-frequency noise

    Directory of Open Access Journals (Sweden)

    Yukio Takahashi

    2011-01-01

    Full Text Available To investigate the contribution of body vibrations to the vibratory sensation induced by high-level, complex low-frequency noise, we conducted two experiments. In Experiment 1, eight male subjects were exposed to seven types of low-frequency noise stimuli: two pure tones [a 31.5-Hz, 100-dB(SPL tone and a 50-Hz, 100-dB(SPL tone] and five complex noises composed of the pure tones. For the complex noise stimuli, the sound pressure level of one tonal component was 100 dB(SPL and that of another one was either 90, 95, or 100 dB(SPL. Vibration induced on the body surface was measured at five locations, and the correlation with the subjective rating of the vibratory sensation at each site of measurement was examined. In Experiment 2, the correlation between the body surface vibration and the vibratory sensation was similarly examined using seven types of noise stimuli composed of a 25-Hz tone and a 50-Hz tone. In both the experiments, we found that at the chest and the abdomen, the rating of the vibratory sensation was in close correlation with the vibration acceleration level (VAL of the body surface vibration measured at each corresponding location. This was consistent with our previous results and suggested that at the trunk of the body (the chest and the abdomen, the mechanoreception of body vibrations plays an important role in the experience of the vibratory sensation in persons exposed to high-level low-frequency noise. At the head, however, no close correlation was found between the rating of the vibratory sensation and the VAL of body surface vibration. This suggested that at the head, the perceptual mechanisms of vibration induced by high-level low-frequency noise were different from those in the trunk of the body.

  8. Sleep improvement for restless legs syndrome patients. Part IV: meta-analysis comparison of effect sizes of vibratory stimulation sham pads and placebo pills

    Directory of Open Access Journals (Sweden)

    Burbank F

    2014-02-01

    Full Text Available Fred Burbank Salt Creek International Women's Health Foundation, San Clemente, CA, USA Purpose: To determine whether sham pads used as controls in randomized clinical trials of vibratory stimulation to treat patients with sleep loss associated with restless legs syndrome perform differently than placebo pills used in comparable restless legs syndrome drug trials. Patients and methods: Sham pad effect sizes from 66 control patients in two randomized clinical trials of vibratory stimulation were compared with placebo responses from 1,024 control patients in 12 randomized clinical drug trials reporting subjective sleep measurement scales. Control patient responses were measured as the standardized difference in means corrected for correlation between beginning and ending scores and for small sample sizes. Results: For parallel randomized clinical trials, sham effects in vibratory stimulation trials were not significantly different from placebo effects in drug trials (0.37 and 0.31, respectively, Qbetween subgroups =0.25, PQ≥0.62. Placebo effect sizes were significantly smaller in crossover drug trials than sham effect sizes in parallel vibratory stimulation trials (0.07 versus 0.37, respectively, Qbetween subgroups =4.59, PQ≤0.03 and placebo effect sizes in parallel drug trials (0.07 versus 0.31, respectively, Qbetween subgroups =5.50, PQ≤0.02. Conclusion: For subjective sleep loss assessments in parallel trials, sham pads in vibratory stimulation trials performed similarly to placebo pills in drug trials. Trial design (parallel versus crossover had a large influence on control effect sizes. Placebo pills in crossover drug trials had significantly smaller effect sizes than sham pads in parallel vibratory stimulation trials or placebo pills in parallel drug trials. Keywords: sham effect, placebo effect, trial design, crossover study, parallel study, counterstimulation

  9. Advanced immobilization processes for fuel hulls and dissolver residues

    International Nuclear Information System (INIS)

    Hebel, W.; Boehme, G.; Findlay, J.R.; Sombret, C.

    1984-08-01

    Various research and development projects for the conditioning of cladding scraps and dissolver residues are pursued within the scope of the R and D programme on nuclear waste Management of the European Community. They include the characterization of the waste materials arising from industrial fuel reprocessing and the development of different waste immobilization techniques. These concern the embedment of scraps and residues into inert matrices like cement, metal alloys, compacted graphite and sintered ceramics as well as the treatment of the fuel hulls by melting or chemical conversion. The conditioned waste forms are tested as to their relevant properties for activity enclosure

  10. Advanced immobilization processes for fuel hulls and dissolver residues

    International Nuclear Information System (INIS)

    Hebel, W.; Boehme, G.; Findlay, J.R.; Sombert, C.

    1984-01-01

    Various research and development projects for the conditioning of cladding scraps and dissolver residues are pursued within the scope of the R and D programme on nuclear waste Management of the European Community. They include the characterization of the waste materials arising from industrial fuel reprocessing and the development of different waste immobilization techniques. These concern the embedment of the scraps and residues into inert matrices like cement, metal alloys, compacted graphite and sintered ceramics as well as the treatment of the fuel hulls by melting or chemical conversion. The conditioned waste forms are tested as to their relevant properties for activity enclosure

  11. Study on the preparation of furfural from rice hull

    Energy Technology Data Exchange (ETDEWEB)

    Lu, M.F; Li, P.H.

    1980-01-01

    Furfural (I) was prepared from rice hull by digestion with HCl, H/sub 2/SO4, or H/sub 3/PO4. I formation in the presence of 5N HCl (the optimum concentration) increased with increasing time of digestion up to 5 hours and then decreased. The optimum concentration and time with H/sub 2/SO4 were the same, but digestion with H/sub 3/PO4 was neither concentration nor time dependent. Under optimal conditions, I formation was highest in digestion with HCl.

  12. Offshore wind turbine foundations. Development of a special vibratory hammer with enhanced function; Gruendung von Offshore Windenergieanlagen. Entwicklung einer speziellen Vibrationsramme mit erweiterter Funktion

    Energy Technology Data Exchange (ETDEWEB)

    Koecher, Johannes; Ulrich, Dirk [ThyssenKrupp Tiefbautechnik GmbH, Alsfeld (Germany)

    2013-11-01

    To ensure that steel jacket foundations for offshore wind turbines are securely anchored, they are fixed to the seabed by means of ''pins''. The pins consist of pipe piles weighing up to 140 metric tons, and are driven into the seabed by a vibratory hammer and then anchored by impact driving. ThyssenKrupp Tiefbautechnik has modified a vibratory hammer so that it can pick up the piles horizontally directly from the working ship or pontoon and then vibrate them vertically into the ground. This significantly reduces installation times and foundation costs. (orig.)

  13. Assessment of Real-Time Compaction Quality Test Indexes for Rockfill Material Based on Roller Vibratory Acceleration Analysis

    Directory of Open Access Journals (Sweden)

    Tianbo Hua

    2018-01-01

    Full Text Available Compaction quality is directly related to the structure and seepage stability of a rockfill dam. To timely and accurately test the compaction quality of the rockfill material, four real-time test indexes were chosen to characterize the soil compaction degree based on the analysis of roller vibratory acceleration, including acceleration peak value (ap, acceleration root mean square value (arms, crest factor value (CF, and compaction meter value (CMV. To determine which of these indexes is the most appropriate, a two-part field compaction experiment was conducted using a vibratory roller in different filling zones of the dam body. Data on rolling parameters, real-time test indexes, and compaction quality indexes were collected to perform statistical regression analyses. Combined with the spectrum analysis of the acceleration signal, it was found that the CF index best characterizes the compaction degree of the rockfill material among the four indexes. Furthermore, the quantitative relations between the real-time index and compaction quality index were established to determine the control criterion of CF, which can instruct the site work of compaction quality control in the rockfill rolling process.

  14. maar vandag in 2015 kan hulle gelees word as stories oor mense ...

    African Journals Online (AJOL)

    8 Apr 2016 ... maar vandag in 2015 kan hulle gelees word as stories oor mense wat leef teen die agtergrond van politieke opstand en sosiale chaos binne 'n groter universele verband. Die verbeeldingspel wat geïn- spireer word deur die teater, bied in die dramatekste van Uys 'n legio visuele moontlikhede van hoe hulle ...

  15. Distributed Topological Convex Hull Estimation of Event Region in Wireless Sensor Networks without Location Information

    NARCIS (Netherlands)

    Guo, Peng; Cao, Jiannong; Zhang, Kui

    2015-01-01

    In critical event (e.g., fire or gas) monitoring applications of wireless sensor networks (WSNs), convex hull of the event region is an efficient tool in handling the usual tasks like event report, routes reconstruction and human motion planning. Existing works on estimating convex hull of event

  16. Effects of quinoa hull meal on piglet performance and intestinal epithelial physiology

    DEFF Research Database (Denmark)

    Carlson, Dorthe; Fernandez, J.A.; Poulsen, H.D.

    2012-01-01

    Saponin-containing feed additives have shown positive effects on pig performance. Quinoa hull has high saponin content and may be of interest as a feed additive. This study aimed to evaluate quinoa hull meal (QHM) as a feed additive in a pig diet. The effects of QHM were assessed for three dosages...

  17. 33 CFR 187.321 - What are the hull identification number (HIN) provisions?

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false What are the hull identification number (HIN) provisions? 187.321 Section 187.321 Navigation and Navigable Waters COAST GUARD, DEPARTMENT... Vessel Titling Systems § 187.321 What are the hull identification number (HIN) provisions? A State must...

  18. 46 CFR 42.09-35 - Additional survey requirements for wood-hull vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Additional survey requirements for wood-hull vessels. 42.09-35 Section 42.09-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES... Additional survey requirements for wood-hull vessels. (a) In addition to the requirements in § 42.09-25, the...

  19. Gamma radiation effects on phenolics, antioxidants activity and in vitro digestion of pistachio (Pistachia vera) hull

    International Nuclear Information System (INIS)

    Behgar, M.; Ghasemi, S.; Naserian, A.; Borzoie, A.; Fatollahi, H.

    2011-01-01

    The effect of gamma radiation (10, 20, 30, 40, 50 and 60 kGy) on tannin, total phenolics, antioxidants activity and in vitro digestion of pistachio hulls has been investigated in this study. The possibility of using the radial diffusion method based on software measurement of the rings area has also been investigated in this study. The software based method in radial diffusion method showed a higher r 2 (0.995) value when compared to the traditional method. Irradiation reduced the tannin content (P<0.01) and activity of antioxidants (P<0.05) of pistachio hull extracts but increased the total phenolic content (P<0.05). There was no effect of gamma irradiation on the in vitro digestion of the pistachio hull. Irradiation decreased the digestion rate of the pistachio hull at the dose of 40 kGy when compared to the control. This study showed that gamma irradiation decreased tannin and antioxidants activity of pistachio hull. - Highlights: → we investigate the effects of gamma irradiation on pistachio hull. → We examine changes in phenolics, antioxidant and digestion of pistachio hull. → Computerized radial diffusion method gives precise regression for standard curve. → Gamma irradiation will decrease tannin and antioxidants of pistachio hull extracts.

  20. Effect of rice hull mulch on nutrient concentration of fertilized irrigation water

    Science.gov (United States)

    Parboiled rice hulls are an effective mulch for controlling weeds in nursery containers. A layer of rice hulls between 1.25 and 2.5 cm deep has been shown to provide effective control of liverwort (Marchantia polymorpha), bittercress (Cardamine flexuosa), and creeping woodsorrel (Oxalis corniculata...

  1. Refined universal laws for hull volumes and perimeters in large planar maps

    International Nuclear Information System (INIS)

    Guitter, Emmanuel

    2017-01-01

    We consider ensembles of planar maps with two marked vertices at distance k from each other, and look at the closed line separating these vertices and lying at distance d from the first one ( d   <   k ). This line divides the map into two components, the hull at distance d which corresponds to the part of the map lying on the same side as the first vertex and its complementary. The number of faces within the hull is called the hull volume, and the length of the separating line the hull perimeter. We study the statistics of the hull volume and perimeter for arbitrary d and k in the limit of infinitely large planar quadrangulations, triangulations and Eulerian triangulations. We consider more precisely situations where both d and k become large with the ratio d / k remaining finite. For infinitely large maps, two regimes may be encountered: either the hull has a finite volume and its complementary is infinitely large, or the hull itself has an infinite volume and its complementary is of finite size. We compute the probability for the map to be in either regime as a function of d / k as well as a number of universal statistical laws for the hull perimeter and volume when maps are conditioned to be in one regime or the other. (paper)

  2. Gamma radiation effects on phenolics, antioxidants activity and in vitro digestion of pistachio (Pistachia vera) hull

    Energy Technology Data Exchange (ETDEWEB)

    Behgar, M [Agricultural, Medical and Industrial Research School, P.O. Box 31485498, Karaj (Iran, Islamic Republic of); Ghasemi, S; Naserian, A [Faculty of Agriculture, Excellence Center in Animal Science, Ferdowsi University of Mashhad, P.O. Box 917751163, Mashhad (Iran, Islamic Republic of); Borzoie, A; Fatollahi, H [Agricultural, Medical and Industrial Research School, P.O. Box 31485498, Karaj (Iran, Islamic Republic of)

    2011-09-15

    The effect of gamma radiation (10, 20, 30, 40, 50 and 60 kGy) on tannin, total phenolics, antioxidants activity and in vitro digestion of pistachio hulls has been investigated in this study. The possibility of using the radial diffusion method based on software measurement of the rings area has also been investigated in this study. The software based method in radial diffusion method showed a higher r{sup 2} (0.995) value when compared to the traditional method. Irradiation reduced the tannin content (P<0.01) and activity of antioxidants (P<0.05) of pistachio hull extracts but increased the total phenolic content (P<0.05). There was no effect of gamma irradiation on the in vitro digestion of the pistachio hull. Irradiation decreased the digestion rate of the pistachio hull at the dose of 40 kGy when compared to the control. This study showed that gamma irradiation decreased tannin and antioxidants activity of pistachio hull. - Highlights: > we investigate the effects of gamma irradiation on pistachio hull. > We examine changes in phenolics, antioxidant and digestion of pistachio hull. > Computerized radial diffusion method gives precise regression for standard curve. > Gamma irradiation will decrease tannin and antioxidants of pistachio hull extracts.

  3. 46 CFR 167.15-25 - Inspection standards for hulls, boilers and machinery.

    Science.gov (United States)

    2010-10-01

    ... SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-25 Inspection standards for hulls, boilers and... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection standards for hulls, boilers and machinery... inspection. These rules may be purchased from the American Bureau of Shipping (ABS), ABS Plaza, 16855...

  4. Development and application of α-hull and Voronoi diagrams in the assessment of roundness error

    International Nuclear Information System (INIS)

    Li, Xiuming; Liu, Hongqi; Li, Wei

    2011-01-01

    Computational geometry has been used to select effective data points from the measured data points for evaluating the roundness error to improve the computational complexity. However, for precision parts most of the measured points are on the vertices of the convex hull; it cannot have any effect on improving the computational complexity with the Voronoi diagrams. In this paper the roundness error is evaluated with α-hull and the Voronoi diagram instead of convex hull. An approach for constructing α-hull with the minimum radius separation is presented to determine the vertices of the Voronoi diagram. The experimental results showed that the roundness error of the minimum zone circle could be solved efficiently with α-hull and the Voronoi diagram

  5. Gamma radiation effects on phenolics, antioxidants activity and in vitro digestion of pistachio ( Pistachia vera) hull

    Science.gov (United States)

    Behgar, M.; Ghasemi, S.; Naserian, A.; Borzoie, A.; Fatollahi, H.

    2011-09-01

    The effect of gamma radiation (10, 20, 30, 40, 50 and 60 kGy) on tannin, total phenolics, antioxidants activity and in vitro digestion of pistachio hulls has been investigated in this study. The possibility of using the radial diffusion method based on software measurement of the rings area has also been investigated in this study. The software based method in radial diffusion method showed a higher r2 (0.995) value when compared to the traditional method. Irradiation reduced the tannin content ( Ppistachio hull extracts but increased the total phenolic content ( Ppistachio hull. Irradiation decreased the digestion rate of the pistachio hull at the dose of 40 kGy when compared to the control. This study showed that gamma irradiation decreased tannin and antioxidants activity of pistachio hull.

  6. Automated Visual Inspection of Ship Hull Surfaces Using the Wavelet Transform

    Directory of Open Access Journals (Sweden)

    Carlos Fernández-Isla

    2013-01-01

    Full Text Available A new online visual inspection technique is proposed, based on a wavelet reconstruction scheme over images obtained from the hull. This type of visual inspection to detect defects in hull surfaces is commonly carried out at shipyards by human inspectors before the hull repair task starts. We propose the use of Shannon entropy for automatic selection of the band for image reconstruction which provides a low decomposition level, thus avoiding excessive degradation of the image, allowing more precise defect segmentation. The proposed method here is capable of on-line assisting to a robotic system to perform grit blasting operations over damage areas of ship hulls. This solution allows a reliable and cost-effective operation for hull grit spot blasting. A prototype of the automated blasting system has been developed and tested in the Spanish NAVANTIA shipyards.

  7. Pro Spring security

    CERN Document Server

    Scarioni, Carlo

    2013-01-01

    Security is a key element in the development of any non-trivial application. The Spring Security Framework provides a comprehensive set of functionalities to implement industry-standard authentication and authorization mechanisms for Java applications. Pro Spring Security will be a reference and advanced tutorial that will do the following: Guides you through the implementation of the security features for a Java web application by presenting consistent examples built from the ground-up. Demonstrates the different authentication and authorization methods to secure enterprise-level applications

  8. Instant Spring security starter

    CERN Document Server

    Jagielski, Piotr

    2013-01-01

    Get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks. A concise guide written in an easy-to-follow format following the Starter guide approach.This book is for people who have not used Spring Security before and want to learn how to use it effectively in a short amount of time. It is assumed that readers know both Java and HTTP protocol at the level of basic web programming. The reader should also be familiar with Inversion-of-Control/Dependency Injection, preferably with the Spring framework itsel

  9. 46 CFR 71.50-27 - Alternative Hull Examination (AHE) program options: Divers or underwater remotely operated...

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) program options...-27 Alternative Hull Examination (AHE) program options: Divers or underwater remotely operated vehicle... operations; (2) Provide permanent hull markings, a temporary grid system of wires or cables spaced not more...

  10. 46 CFR 115.620 - Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Description of the Alternative Hull Examination (AHE... ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.620 Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels. The Alternative...

  11. 46 CFR 71.50-15 - Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Description of the Alternative Hull Examination (AHE... Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels. The Alternative Hull Examination (AHE) Program provides you with an alternative to a drydock examination by allowing...

  12. 46 CFR 71.50-3 - Drydock examination, internal structural examination, underwater survey, and alternate hull exam...

    Science.gov (United States)

    2010-10-01

    ..., underwater survey, and alternate hull exam intervals. 71.50-3 Section 71.50-3 Shipping COAST GUARD...-3 Drydock examination, internal structural examination, underwater survey, and alternate hull exam... wooden hulls must undergo two drydock and two internal structural examinations within any five year...

  13. 46 CFR 115.625 - Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain passenger...

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Eligibility requirements for the Alternative Hull... OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.625 Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain...

  14. 46 CFR 71.50-17 - Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain passenger...

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Eligibility requirements for the Alternative Hull...-17 Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain passenger... aluminum; (2) It has an effective hull protection system; (3) It has operated exclusively in fresh water...

  15. CYTOTOXIC AND ANTIOXIDANT ACTIVITY OF BUCKWHEAT HULL EXTRACTS

    Directory of Open Access Journals (Sweden)

    Martina Danihelová

    2013-02-01

    Full Text Available Buckwheat contains many prophylactic compounds that are concentrated mainly in outer layers of buckwheat grain. The aim of this study was to prepare buckwheat hull extracts. Ten buckwheat cultivars were screened for their antioxidant and anticancer properties. Total polyphenol content was determined using Folin-Ciocalteau's reagent. Antioxidant activity was established by the method of binding free radical DPPH. Cytotoxic properties were measured on human cervical cancer cells HeLa using mitochondrial cytotoxic test (MTT. Total polyphenol content ranged from 166.67 to 635.31 mg GAE/100 g DW. The highest content displayed tartary buckwheat cultivar Madawaska (0.64% of hulls weight. Among common buckwheat the richest in polyphenols were cultivars Bamby and KASHO-2. The best free radical binding antioxidant activity was found for cultivars with highest polyphenol content. This relationship was not observed for cytotoxic action on human cervical cancer cells. The best growth inhibitory activity on HeLa cancer cells displayed common buckwheat cultivars Bamby and KASHO-2 (up to 50%, extract concentration 100 µg/ml. This was not found for tartary buckwheat cultivar Madawaska.

  16. Methylene blue adsorption from aqueous solution by dehydrated peanut hull

    Energy Technology Data Exchange (ETDEWEB)

    Ozer, Dursun [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey); Dursun, Guelbeyi [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)]. E-mail: gdursun@firat.edu.tr; Ozer, Ahmet [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)

    2007-06-01

    Dyes are colour organic compounds which can colorize the other substances. These substances usually presents in the effluent water of many industries, such as textiles, leather, paper, printing and cosmetics. To observe the potential feasibility of removing colour, peanut hull as an agricultural by-product was dehydrated with sulphuric acid (DPH) and used for adsorption of methylene blue (MB) from aqueous solution. The effects of various parameters such as initial methylene blue concentrations, temperatures and particle sizes were examined and optimal experimental conditions were determined. Adsorption data were well described by the Langmuir model, although they could be modelled by the Freundlich model as well. The adsorption process followed the pseudo-second order kinetic model. The mass transfer model as intraparticle diffusion was applied to the experimental data to examine the mechanisms of rate controlling step. It was found that at the higher initial MB concentration, intraparticle diffusion is becoming significant controlling step. The thermodynamic constants of the adsorption process were also evaluated by using the Langmuir constants related to the equilibrium of adsorption at different temperatures. The results in this study indicated that dehydrated peanut hull was a good adsorbent for removing methylene blue.

  17. The role of Bh4 in parallel evolution of hull colour in domesticated and weedy rice.

    Science.gov (United States)

    Vigueira, C C; Li, W; Olsen, K M

    2013-08-01

    The two independent domestication events in the genus Oryza that led to African and Asian rice offer an extremely useful system for studying the genetic basis of parallel evolution. This system is also characterized by parallel de-domestication events, with two genetically distinct weedy rice biotypes in the US derived from the Asian domesticate. One important trait that has been altered by rice domestication and de-domestication is hull colour. The wild progenitors of the two cultivated rice species have predominantly black-coloured hulls, as does one of the two U.S. weed biotypes; both cultivated species and one of the US weedy biotypes are characterized by straw-coloured hulls. Using Black hull 4 (Bh4) as a hull colour candidate gene, we examined DNA sequence variation at this locus to study the parallel evolution of hull colour variation in the domesticated and weedy rice system. We find that independent Bh4-coding mutations have arisen in African and Asian rice that are correlated with the straw hull phenotype, suggesting that the same gene is responsible for parallel trait evolution. For the U.S. weeds, Bh4 haplotype sequences support current hypotheses on the phylogenetic relationship between the two biotypes and domesticated Asian rice; straw hull weeds are most similar to indica crops, and black hull weeds are most similar to aus crops. Tests for selection indicate that Asian crops and straw hull weeds deviate from neutrality at this gene, suggesting possible selection on Bh4 during both rice domestication and de-domestication. © 2013 The Authors. Journal of Evolutionary Biology © 2013 European Society For Evolutionary Biology.

  18. Non-destructive assay of leached hulls in a nuclear fuel reprocessing plant

    International Nuclear Information System (INIS)

    Hofstetter, K.J.; Henderson, B.C.; Gray, J.H.; Huff, G.A.

    1978-01-01

    The hull monitor at the Barnwell Nuclear Fuels Plant (BNFP) will be a remotely controlled, fully automated system designed to quantitatively assay leached hulls for undissolved U and Pu. The hull monitor will assay the hulls from one metric ton of fuel per dissolver basket with the design goal of detecting 0.1% undissolved fuel and yet remain within the framework of the BNFP materials flow of five hull baskets per day. The non-destructive assay will be accomplished using a computer-based gamma-ray pulse height analysis system employing a 5 x 5 inch NaI(Tl) scintillation detector. The intense radiations from the fission product isotopes and the activation product isotopes produced in the reactor prevent direct assay of the undissolved fuel left in the hulls. The measurement will be made indirectly by demonstrating a correlation between the amount of 144 Ce undissolved and the remaining U. The isotope 144 Ce is a direct fission product with high cumulative yield. The daughter isotope 144 Pr has a gamma ray at 2.18 MeV well above other predominant radiations in the spectrum from the major interferences 60 Co, 58 Co, 95 Zr( 95 Nb), 137 Cs and 106 Ru( 106 Rh). Segmented scanning operation of the hull monitor is accomplished by rotation and vertical transversal of the hulls container past the detector station. Proper collimation and absorbers are required to maximize the 144 Ce( 144 Pr) to background ratio. A basket indexer is provided which monitors the scanning rate and ensures repositioning. The leached hull monitor system will be interfaced to a computer-based multichannel analyzer for ease of operation and data handling. A calibration basket has been fabricated to accomodate radioactive sources and inactive Zircaloy hulls

  19. Mercury content in Hot Springs

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, R

    1974-01-01

    A method of determination of mercury in hot spring waters by flameless atomic absorption spectrophotometry is described. Further, the mercury content and the chemical behavior of the elementary mercury in hot springs are described. Sulfide and iodide ions interfered with the determination of mercury by the reduction-vapor phase technique. These interferences could, however, be minimized by the addition of potassium permanganate. Waters collected from 55 hot springs were found to contain up to 26.0 ppb mercury. High concentrations of mercury have been found in waters from Shimoburo Springs, Aomori (10.0 ppb), Osorezan Springs, Aomori (1.3 approximately 18.8 ppb), Gosyogake Springs, Akita (26.0 ppb), Manza Springs, Gunma (0.30 approximately 19.5 ppb) and Kusatu Springs, Gunma (1.70 approximately 4.50 ppb). These hot springs were acid waters containing a relatively high quantity of chloride or sulfate.

  20. A Quadratic Spring Equation

    Science.gov (United States)

    Fay, Temple H.

    2010-01-01

    Through numerical investigations, we study examples of the forced quadratic spring equation [image omitted]. By performing trial-and-error numerical experiments, we demonstrate the existence of stability boundaries in the phase plane indicating initial conditions yielding bounded solutions, investigate the resonance boundary in the [omega]…

  1. Spring batch essentials

    CERN Document Server

    Rao, P Raja Malleswara

    2015-01-01

    If you are a Java developer with basic knowledge of Spring and some experience in the development of enterprise applications, and want to learn about batch application development in detail, then this book is ideal for you. This book will be perfect as your next step towards building simple yet powerful batch applications on a Java-based platform.

  2. Effects of repeated vibratory stimulation of wrist and elbow flexors on hand dexterity, strength, and sensory function in patients with chronic stroke: a pilot study.

    Science.gov (United States)

    Choi, Won-Ho

    2017-04-01

    [Purpose] The aim of this study was to investigate the effects of repeated vibratory stimulation to muscles related to hand functions on dexterity, strength, and sensory function in patients with chronic stroke. [Subjects and Methods] A total of 10 stroke patients with hemiplegia participated in this study. They were divided into two groups: a) Experimental and b) Control, with five randomly selected subjects for each group. The experimental group received vibratory stimulation, while the control group received the traditional physical therapy. Both interventions were performed for 30 minutes each session, three times a week for four weeks. [Results] There was a significant within-group improvement in the box and block test results in both groups for dexterity. Grip strength improved in both groups but the improvement was not statistically significant. [Conclusion] The vibratory stimulation activated the biceps brachii and flexor carpi radialis, which increased dexterity to grasp and lift the box and block from the surface. Therefore, repeated vibratory stimulation to muscles related to hand functions improved hand dexterity equality to the traditional physical therapy in patients with chronic stroke.

  3. A smart ROV solution for ship hull and harbor inspection

    Science.gov (United States)

    Reed, Scott; Wood, Jon; Vazquez, Jose; Mignotte, Pierre-Yves; Privat, Benjamin

    2010-04-01

    Hull and harbor infrastructure inspections are frequently performed manually and involve quite a bit of risk and human and monetary resources. In any kind of threat and resource constrained environment, this involves unacceptable levels of risk and cost. Modern Remotely Operated Vehicles are highly refined machines that provide features and capabilities previously unavailable. Operations once carried out by divers can now be carried out more quickly, efficiently and safely by smart enabled ROVs. ROVs are rapidly deployable and capable of continuous, reliable operations in adverse conditions. They also provide a stable platform on which multiple sensors may be mounted and utilized to meet the harbor inspection problem. Automated Control software provides ROV's and their pilots with the capability to inspect complex, constrained environments such as those found in a harbor region. This application and the user interface allow the ROV to automatically conduct complex maneuvers relative to the area being inspected and relieves the training requirements and work load for the pilot, allowing he or she to focus on the primary task of survey, inspection and looking for possible threats (such as IEDs, Limpet Mines, signs of sabotage, etc). Real-time sensor processing tools can be integrated into the smart ROV solution to assist the operator. Automatic Target Recognition (ATR) algorithms are used to search through the sensor data collected by the ROV in real time. These algorithms provide immediate feedback on possible threats and notify the operator of regions that may require manual verification. Sensor data (sonar or video) is also mosaiced, providing the operator with real-time situational awareness and a coverage map of the hull or seafloor. Detected objects may also be placed in the context of the large scale characteristics of the hull (or bottom or pilings) and localized. Within the complex areas such as the harbor pier pilings and the running gear of the ship, real

  4. Studying Springs in Series Using a Single Spring

    Science.gov (United States)

    Serna, Juan D.; Joshi, Amitabh

    2011-01-01

    Springs are used for a wide range of applications in physics and engineering. Possibly, one of their most common uses is to study the nature of restoring forces in oscillatory systems. While experiments that verify Hooke's law using springs are abundant in the physics literature, those that explore the combination of several springs together are…

  5. A Study on the Radioactivity Reduction Method for the Decladding Hull

    International Nuclear Information System (INIS)

    Kim, Jong Ho; Jung, In Ha; Park, Jang Jin; Shin, Jin Myeong; Lee, Ho Hee; Yang, Myung Seung

    1994-01-01

    The cladding materials remaining after reprocessing process of the nuclear fuel, generally called as hulls, are classified as a high-level radioactive waste. They are usually packaged in the container for disposal after being compacted, melted, or solidified into the matrix. The efforts to fabricated a better ingot for a more favorable disposal to the environment have failed due to the technical difficulties encountered in the chemical decontamination method. In the early 1990s, the accumulation of radio-chemical data on hulls and the advent of new technology such as a laser or plasma have made the pre-treatment of the hulls mere efficient. This paper summarizes the information regarding the radio-chemical analysis of the hull through a literature survey and determines the characteristics of the hull and depth profile of the radio-nuclides within the hull thickness. The feasibility study was carried out to evaluate the reduction of the radioactivity by peeling off the surface of the hull with the application of laser technology

  6. Solid-state fermentation of Mortierella isabellina for lipid production from soybean hull.

    Science.gov (United States)

    Zhang, Jianguo; Hu, Bo

    2012-02-01

    Soybean hull, generated from soybean processing, is a lignocellulosic material with limited industrial applications and little market value. This research is exploring a new application of soybean hull to be converted to fungal lipids for biodiesel production through solid-state fermentation. Mortierella isabellina was selected as the oil producer because of its high lipid content at low C/N ratio. Several cultivation factors were investigated, including moisture content, inoculums size, fungal spore age, and nutrient supplements, in an attempt to enhance the lipid production of the solid-state fermentation process. The results showed that lipid production with the increase of the moisture content and the spore age, while decreased as the size of inoculums increased. Nutrients addition (KH₂PO₄ 1.2 mg and MgSO₄ 0.6 mg/g soybean hull) improved the lipid production. The total final lipid reached 47.9 mg lipid from 1 g soybean hull after the conversion, 3.3-fold higher than initial lipid reserve in the soybean hull. The fatty acid profile analysis indicated that fatty acid content consisted of 30.0% of total lipid, and 80.4% of total fatty acid was C16 and C18. Therefore, lipid production from soybean hull is a possible option to enable soybean hull as a new resource for biodiesel production and to enhance the overall oil production from soybeans.

  7. Antioxidant constituents of almond [Prunus dulcis (Mill.) D.A. Webb] hulls.

    Science.gov (United States)

    Takeoka, Gary R; Dao, Lan T

    2003-01-15

    Almond hulls (Nonpareil variety) were extracted with methanol and analyzed by reversed phase HPLC with diode array detection. The extract contained 5-O-caffeoylquinic acid (chlorogenic acid), 4-O-caffeoylquinic acid (cryptochlorogenic acid), and 3-O-caffeoylquinic acid (neochlorogenic acid) in the ratio 79.5:14.8:5.7. The chlorogenic acid concentration of almond hulls was 42.52 +/- 4.50 mg/100 g of fresh weight (n = 4; moisture content = 11.39%). Extracts were tested for their ability to inhibit the oxidation of methyl linoleate at 40 degrees C. At an equivalent concentration (10 microg/1 g of methyl linoleate) almond hull extracts had higher antioxidant activity than alpha-tocopherol. At higher concentrations (50 microg/1 g of methyl linoleate) almond hull extracts showed increased antioxidant activity that was similar to chlorogenic acid and morin [2-(2,4-dihydroxyphenyl)-3,5,7-trihydroxy-4H-1-benzopyran-4-one] standards (at the same concentrations). These data indicate that almond hulls are a potential source of these dietary antioxidants. The sterols (3beta,22E)-stigmasta-5,22-dien-3-ol (stigmasterol) and (3beta)-stigmast-5-en-3-ol (beta-sitosterol) (18.9 mg and 16.0 mg/100 g of almond hull, respectively) were identified by GC-MS of the silylated almond hull extract.

  8. Effects of biofouling development on drag forces of hull coatings for ocean-going ships: a review

    DEFF Research Database (Denmark)

    Lindholdt, Asger; Dam-Johansen, Kim; Olsen, S. M.

    2015-01-01

    This review presents a systematic overview of the literature and describes the experimental methods used to quantify the drag of hull coatings. It also summarizes the findings of hull coating's drag performance and identifies the main parameters impacting it. The advantages and disadvantages...... of the reported methods listed in this review provide an assessment of the most efficient methods to quantify the drag performance of hull coatings. This review determines that drag performance of hull coating technology varies depending on whether the coating condition is newly applied, after dynamic or static...... seawater exposure. The summarized data reveal that, while several methods have attempted to quantify drag performance of hull coatings, other methods must be explored in order to accurately measure the long-term drag performance of hull coatings in conditions mimicking those that ship hulls encounter...

  9. Classification of Fusarium-Infected Korean Hulled Barley Using Near-Infrared Reflectance Spectroscopy and Partial Least Squares Discriminant Analysis

    Directory of Open Access Journals (Sweden)

    Jongguk Lim

    2017-09-01

    Full Text Available The purpose of this study is to use near-infrared reflectance (NIR spectroscopy equipment to nondestructively and rapidly discriminate Fusarium-infected hulled barley. Both normal hulled barley and Fusarium-infected hulled barley were scanned by using a NIR spectrometer with a wavelength range of 1175 to 2170 nm. Multiple mathematical pretreatments were applied to the reflectance spectra obtained for Fusarium discrimination and the multivariate analysis method of partial least squares discriminant analysis (PLS-DA was used for discriminant prediction. The PLS-DA prediction model developed by applying the second-order derivative pretreatment to the reflectance spectra obtained from the side of hulled barley without crease achieved 100% accuracy in discriminating the normal hulled barley and the Fusarium-infected hulled barley. These results demonstrated the feasibility of rapid discrimination of the Fusarium-infected hulled barley by combining multivariate analysis with the NIR spectroscopic technique, which is utilized as a nondestructive detection method.

  10. Penile vibratory stimulation in the recovery of urinary continence and erectile function after nerve-sparing radical prostatectomy

    DEFF Research Database (Denmark)

    Fode, Mikkel; Borre, Michael; Ohl, Dana A

    2014-01-01

    OBJECTIVE: To examine the effect of penile vibratory stimulation (PVS) in the preservation and restoration of erectile function and urinary continence in conjunction with nerve-sparing radical prostatectomy (RP). PATIENTS AND METHODS: The present study was conducted between July 2010 and March 2013...... were instructed in using a PVS device (FERTI CARE(®) vibrator). Stimulation was performed at the frenulum once daily by the patients in their own homes for at least 1 week before surgery. After catheter removal, daily PVS was re-initiated for a period of 6 weeks. Participants were evaluated at 3, 6...... for analyses (30 patients randomized to PVS and 38 patients randomized to the control group). The IIEF-5 score was highest in the PVS group at all time points after surgery with a median score of 18 vs 7.5 in the control group at 12 months (P = 0.09), but the difference only reached borderline significance...

  11. Development and assessment of two decontamination processes: closed electropolishing system for decontamination of underwater surfaces -vibratory decontamination with abrasives

    International Nuclear Information System (INIS)

    Benavides, E.; Fajardo, M.

    1992-01-01

    Two decontamination processes have been developed to decontaminate the stainless steel components of nuclear power plants. The first process uses an underwater closed electropolishing system for the decontamination of large stainless steel surfaces in flooded systems without loss of electrolyte. Large underwater contaminated areas can be treated with an electropolishing head covering an area of 2 m 2 in one step. The decontamination factors achieved with this technique range between 100 and 1000. The second process consists in the decontamination of nuclear components using vibratory equipment with self-cleaning abrasives generating a minimum quantity of waste. This technique may reach contamination factors similar to those obtained with other abrasive methods (brush abrasion, abrasive blasting, etc...). The obtained decontamination factors range between 5 and 50. Only a small quantity of waste is generated, which is treated and reduced in volume by filtration and evaporation

  12. Development of Cell Culture Microdevice Actuated by Piezoelectric Thin Films for Delivering Mechanical Vibratory Stimuli to Cells

    International Nuclear Information System (INIS)

    Yamada, Y; Umegaki, G; Kawashima, T; Nagai, M; Shibata, T; Masuzawa, T; Kimura, T; Kishida, A

    2012-01-01

    In order to realize a cell culture microdevice actuated by piezoelectric thin films for on-chip regulation of cell functions, this paper reported on a feasibility study by using the microdevice with KOH-etched cavities surrounded by four (111) sidewalls as microchambers in order to introduce cells to be cultured. As a result, the vibration characteristic of the PZT actuator was improved by using an electric field -150 kV/cm at 70 C for 30 min in poling process. A feasibility study on cell culture for delivering mechanical vibratory stimuli to cells revealed the microdevice could be applicable to the culture with actual biological cells. In addition, it was found that O 2 -plasma treated parylene-C process could be applicable for obtaining homogeneous surface of cell culture microdevice.

  13. Evaluation of management alternatives for LWR hulls and caps

    International Nuclear Information System (INIS)

    Chaudon, L.; Mehling, O.; Cecille, L.; Thiels, G.; Kowa, S.

    1993-01-01

    Hulls and caps resulting from the reprocessing of LWR spent fuels represent one of the major sources of alpha-bearing solid waste generated during the nuclear fuel cycle. The Commission of the European Communities has undertaken considerable R and D efforts on the development of advanced treatment and conditioning methods for this type of waste. In view of the encouraging results achieved, the Commission launched a theoretical assessment study on cladding waste management. Six practical or potential schemes were identified and elaborated: direct cementation, decontamination prior to cementation, rolling before cementation, rolling followed by embedding in graphite, compaction, and melting in a cold crucible. The economic aspects of each management option were also investigated. This included the assessment of the plant (treatment, conditioning and interim storage), transport and disposal costs. Further consideration will be required to define the best management option for 'cap' wastes. Transport and disposal costs will also require further analysis from an industrial standpoint

  14. INTEGRATION OF SHIP HULL ASSEMBLY SEQUENCE PLANNING, SCHEDULING AND BUDGETING

    Directory of Open Access Journals (Sweden)

    Remigiusz Romuald Iwańkowicz

    2015-02-01

    Full Text Available The specificity of the yard work requires the particularly careful treatment of the issues of scheduling and budgeting in the production planning processes. The article presents the method of analysis of the assembly sequence taking into account the duration of individual activities and the demand for resources. A method of the critical path and resource budgeting were used. Modelling of the assembly was performed using the acyclic graphs. It has been shown that the assembly sequences can have very different feasible budget regions. The proposed model is applied to the assembly processes of large-scale welded structures, including the hulls of ships. The presented computational examples have a simulation character. They show the usefulness of the model and the possibility to use it in a variety of analyses.

  15. Conversion of rice hull ash into soluble sodium silicate

    Directory of Open Access Journals (Sweden)

    Edson Luiz Foletto

    2006-09-01

    Full Text Available Sodium silicate is used as raw material for several purposes: silica gel production, preparation of catalysts, inks, load for medicines, concrete hardening accelerator, component of detergents and soaps, refractory constituent and deflocculant in clay slurries. In this work sodium silicate was produced by reacting rice hull ash (RHA and aqueous sodium hydroxide, in open and closed reaction systems. The studied process variables were time, temperature of reaction and composition of the reaction mixture (expressed in terms of molar ratios NaOH/SiO2 and H2O/SiO2. About 90% silica conversion contained in the RHA into sodium silicate was achieved in closed system at 200 °C. The results showed that sodium silicate production from RHA can generate aggregate value to this residue.

  16. Methods of conditioning waste fuel decladding hulls and dissolver residues

    International Nuclear Information System (INIS)

    De Regge, P.; Loida, A.; Schmidt-Hansberg, T.; Sombret, C.

    1985-01-01

    Several methods for conditioning spent fuel decladding hulls or dissolver residues have been considered in various countries of the European Community. Five of these methods used embedding technique with or without prior compaction: they are based on incorporation in metallic alloys, glass, ceramics, cements and metals or graphite compounds. A sixth one consists in melting the decladding materials. The corresponding research programmes have been pursued to varying states of progress with regard to demonstrating their feasibility on an industrial scale and the use of genuine wastes in bench scale experiments. The properties of the conditioned wastes have been investigated. Special attention has been paid to the corrosion resistance to various aqueous media as tap water, brine or clayey water. Although no categorical conclusion can be drawn from the initial results, the available findings provide a basis for assessing the different processes

  17. Bioinspired spring origami

    Science.gov (United States)

    Faber, Jakob A.; Arrieta, Andres F.; Studart, André R.

    2018-03-01

    Origami enables folding of objects into a variety of shapes in arts, engineering, and biological systems. In contrast to well-known paper-folded objects, the wing of the earwig has an exquisite natural folding system that cannot be sufficiently described by current origami models. Such an unusual biological system displays incompatible folding patterns, remains open by a bistable locking mechanism during flight, and self-folds rapidly without muscular actuation. We show that these notable functionalities arise from the protein-rich joints of the earwig wing, which work as extensional and rotational springs between facets. Inspired by this biological wing, we establish a spring origami model that broadens the folding design space of traditional origami and allows for the fabrication of precisely tunable, four-dimensional–printed objects with programmable bioinspired morphing functionalities.

  18. Immobilization of Saccharomyces Cerevisiae in Rice Hulls for Ethanol Production

    Directory of Open Access Journals (Sweden)

    Edita Martini

    2011-05-01

    Full Text Available The whole cell immobilization in ethanol fermentation can be done by using natural carriers or through synthetic carriers. All of these methods have the same purpose of retaining high cell concentrations within a certain defined region of space which leads to higher ethanol productivity. Lignocellulosic plant substance represents one of highly potential sources in ethanol production. Some studies have found that cellulosic substances substances can also be used as a natural carrier in cell immobilization by re-circulating pre-culture medium into a reactor. In this experiment, rice hulls without any treatment were used to immobilize Saccharomyces cerevisiae through semi solid state incubation combined with re-circulating pre-culture medium. The scanning electron microscopy (SEM pictures of the carrier show that the yeast cells are absorbed and embedded to the rice hull pore. In liquid batch fermentation system with an initial sugar concentration of 50 g/L, nearly 100% total sugar was consumed after 48 hours. This resulted in an ethanol yield of 0.32 g ethanol/g glucose, which is 62.7% of the theoretical value. Ethanol productivity of 0.59 g/(L.h is 2.3 fold higher than that of free cells which is 0.26 g/(L.h. An effort to reuse the immobilized cells in liquid fermentation system showed poor results due to cell desorption in the first batch which led to high sugar concentration inhibitory effect in the second batch fermentation. This might be solved by using semi solid fermentation process in the future work.

  19. Decontamination of fast reactor hulls and properties of immobilised waste forms

    International Nuclear Information System (INIS)

    Biddle, P.; Brown, P.E.; Rees, J.H.

    1984-01-01

    The objectives of this contract are threefold: (i) to characterise the activities associated with genuine hulls generated in reprocessing fuel from the Prototype Fast Reactor; (ii) to examine the feasibility of decontaminating the hulls by the use of simple low-temperature techniques; and (iii) to immobilise the hulls in cement and evaluate the products. Over the last year, work has concentrated in areas (i) and (ii), but the balance of the programme is now shifting more towards topic (iii). Progress is reported. (author)

  20. Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

    Directory of Open Access Journals (Sweden)

    Hee-Jong Choi

    2011-12-01

    Full Text Available In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60 hull and KRISO container ship (KCS, a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI. The computational results were validated by comparing with the existing experimental data.

  1. Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

    Science.gov (United States)

    Choi, Hee-Jong; Chun, Ho-Hwan; Park, Il-Ryong; Kim, Jin

    2011-12-01

    In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60) hull and KRISO container ship (KCS), a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI). The computational results were validated by comparing with the existing experimental data.

  2. Computer-generated vibratory signatures for EDF PWR reactor vessel internals

    International Nuclear Information System (INIS)

    Trenty, A.; Lefevre, F.; Garreau, D.

    1992-07-01

    This paper presents a device for generation of characteristic signatures for normal or faulty vibrations on EDF PWR internal structures. The objective is to test the efficiency of methods for diagnosing faults in these structures. With this device, it is possible to build an entire PSD in several phases: choice of a general basic shape, localized addition of several kinds of background noise, generation of peaks of variable shapes, adjustment of local or global amplifications... It also offers the possibility of distorting real PSDs acquired from the reactor: shifting frequency or modifying peak shape, eliminating or adding existing shapes or shapes to be created, smoothing curves... One example is given of simulated loss of function in a hold-down spring on a computer-generated PSD of ex-core neutron noise. The device is now being used to test the potential of neural networks in recognizing faults on internal structures

  3. Consolidation of cladding hulls from the electrometallurgical treatment of spent fuel

    International Nuclear Information System (INIS)

    Keiser, D.D. Jr.

    1998-01-01

    To consolidate metallic waste that is residual from Argonne National Laboratory's electrometallurgical treatment of spent nuclear fuel, waste ingots are currently being cast using an induction furnace located in a hot cell. These ingots, which have been developed to serve as final waste forms destined for repository disposal, are stainless steel (SS)-Zr alloys (the Zr is very near 15 wt.%). The charge for the alloys consists of stainless steel cladding hulls, Zr from the fuel being treated, noble metal fission products, and minor amounts of actinides that are present with the cladding hulls. The actual in-dated cladding hulls have been characterized before they were melted into ingots, and the final as-cast ingots have been characterized to determine the degree of consolidation of the charge material. It has been found that ingots can be effectively cast from irradiated cladding hulls residual from the electrometallurgical treatment process by employing an induction furnace located in a hot cell

  4. Nondestructive determination of residual fuel on leached hulls and dissolver sludges from LWR fuel reprocessing

    International Nuclear Information System (INIS)

    Wuerz, H.; Wagner, K.; Becker, H.J.

    1990-01-01

    In reprocessing plants leached hulls and dissolver sludges represent rather important intermediate level α-waste streams. A control of the Pu content of these waste streams is desirable. The nondestructive assay method to be preferred would be passive neutron counting. However, before any decision on passive neutron monitoring becomes possible, a characterization of hulls and sludges in terms of Pu content and neutron emission is necessary. For the direct determination of Plutonium on hulls and in sludges, as coming from reprocessing, an active neutron measurement is required. A simple, and sufficiently sensitive active neutron method which can easily be installed uses a stationary 252 Cf neutron source. This method was used for the characterization of hulls and sludges in terms of Plutonium content and total neutron emission in the Karlsruhe reprocessing plant WAK

  5. Ultrasound assisted extraction of polyphenols and their distribution in whole mung bean, hull and cotyledon.

    Science.gov (United States)

    Singh, Barinderjit; Singh, Narpinder; Thakur, Sheetal; Kaur, Amritpal

    2017-03-01

    In this study, extraction of polyphenols using different solvents (acetone, ethanol, methanol and water) with ultrasound and conventional method from whole mung bean (WMB), hull and cotyledon was conducted. Total phenolic content (TPC), total flavonoids content (TFC), total antioxidant activities (TAA), ferric reducing power (FRP) and DPPH radical scavenging activity were determined. Ultrasound treated extracts exhibited higher TPC, TFC, TAA, FRP and DPPH in different mung bean fractions than CSE. Among the solvents, acetone showed better TPC, TFC, TAA, FRP and DPPH. Hull had significantly higher TPC, TFC, TAA, FRP and DPPH than WMB and cotyledon. Sinapic acid (SA) was the major polyphenol in different fractions. Acetone extract of hull showed high polyphenol content. SA, ferulic acid, catechin, p-coumaric acid, resveratrol, quercetin and luteolin were the major contributors to antioxidant activity of acetone extract. Mung bean hull contained the maximum polyphenols and acetone was observed to be the best extraction medium for polyphenols in combination with ultrasound.

  6. Inhibition of α-glucosidase by polysaccharides from the fruit hull of Camellia oleifera Abel.

    Science.gov (United States)

    Zhang, Sheng; Li, Xiang-Zhou

    2015-01-22

    We isolated and purified polysaccharides from the Camellia oleifera Abel. fruit hull and studied its hypoglycemic potential. Our results revealed six polysaccharides (CFPA-1-5 & CFPB) from the aqueous extract from the defatted C. oleifera fruit hull. Purified polysaccharides (purity >90%) were investigated for the inhibition of α-glucosidase activity in vitro. Two polysaccharides, CFPB and CFPA-3 were present in high concentration in the fruit hull and showed a dose-dependent inhibition of α-glucosidase activity, with IC50 concentrations of 11.80 and 10.95 μg/mL, respectively. This result suggests that polysaccharides (CFP) extracted from the fruit hull of C. oleifera may have potential as functional foods with featuring a hypoglycemic effect. Copyright © 2014 Elsevier Ltd. All rights reserved.

  7. Numerical Simulation of Galvanic Corrosion Caused by Shaft Grounding Systems in Steel Ship Hulls

    National Research Council Canada - National Science Library

    Wang, Y

    2005-01-01

    The shaft grounding systems used on board HMC ships have substantially reduced the shaft-to-hull resistance and, thus, improved the performance of the shipboard impressed current cathodic protection (ICCP) system...

  8. Interest in the glenoid hull method for analyzing humeral subluxation in primary glenohumeral osteoarthritis.

    Science.gov (United States)

    Bouacida, Soufyane; Gauci, Marc-Olivier; Coulet, Bertrand; Lazerges, Cyril; Cyteval, Catherine; Boileau, Pascal; Chammas, Michel

    2017-07-01

    Posterior humeral subluxation is the main cause of failure of total shoulder arthroplasty. We aimed to compare humeral head subluxation in various reference planes and to search for a correlation with retroversion, inclination, and glenoid wear. We included 109 computed tomography scans of primary glenohumeral osteoarthritis and 97 of shoulder problems unrelated to shoulder osteoarthritis (controls); all computed tomography scans were reconstructed in the anatomic scapular plane and the glenoid hull plane that we defined. In both planes, we measured retroversion, inclination, glenohumeral offset (Walch index), and scapulohumeral offset. Retroversion in the scapular plane (Friedman method) was lower than that in the glenoid hull plane for controls and for arthritic shoulders. The threshold of scapulohumeral subluxation was 60% and 65% in the scapular plane and glenoid hull plane, respectively. The mean upward inclination was lower in the scapular plane (Churchill method) than in the glenoid hull plane (Maurer method). In the glenoid hull plane, 35% of type A2 glenoids showed glenohumeral offset greater than 75%, with mean retroversion of 25.6° ± 6° as compared with 7.5° ± 7.2° for the "centered" type A2 glenoids (P hull plane and r = 0.59 in the scapular plane (P hull plane may be more accurate than in the scapular plane. Thus, the glenoid hull method allows for better understanding type B3 of the modified Walch classification. Copyright © 2017 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

  9. David Hull's generalized natural selection as an explanation for scientific change

    Science.gov (United States)

    Little, Michelle Yvette

    2001-10-01

    Philosophers of science such as Karl Popper and Thomas Kuhn have employed evolutionary idiom in describing scientific change. In Science as a Process (1988) Hull makes evolutionary theory explanatorily applicable. He modifies key evolutionary terms in order that both biological evolution and scientific change are instances of a general selection process. According to Hull, because of naturally-existing competition for credit among researchers and the professional lineages they constitute, scientists are constrained to cooperate and collaborate. This process entails two important philosophical consequences. First, it allows for a natural justification of why the sciences can provide objective empirical knowledge. Second, appreciating its strength means that a philosophical analysis of scientific change is solidly difficult features to combine. I work on strengthening two weaknesses in Hull's arguments. First, operating in his analysis is an unexplicated notion of ``information'' running parallel to the equally opaque notion of genetic information. My third chapter provides a clear account of ``genetic information'' whose usefulness extends beyond the assistance it can render Hull as a clear concept is needed in biological contexts as well. The fourth and fifth chapters submit evidence of scientific change from radio astronomy. Hull insists on empirical backing for philosophical theses but his own book stands to suffer from selection effects as it offers cases drawn from a single subspecialty in the biological sciences. I found that in the main scientists and the change they propel accords well with Hull's explanation. However, instances of major change reveal credit- and resource-sharing to a degree contrary with what Hull would expect. My conclusion is that the naturalness of competition, instantiated during the course of standardized and relatively ``normal'' scientific research, is not the norm during periods of new research and its uncertain standards of

  10. Passive non destructive assay of hull waste by gross neutron counting method

    International Nuclear Information System (INIS)

    Andola, Sanjay; Sur, Amit; Rawool, A.M.; Sharma, B.; Kaushik, T.C.; Gupta, S.C.; Basu, Sekhar; Raman Kumar; Agarwal, K.

    2014-01-01

    The special nuclear material accounting (SNMA) is an important and necessary issue now in nuclear waste management. The hull waste generated from dissolution of spent fuel contains small amounts of Uranium and Plutonium and other actinides due to undissolved trapped material inside zircoalloy tubes. We report here on the development of a Passive Hull monitoring system using gross neutron counting technique and its implementation with semiautomatic instrumentation. The overall sensitivity of the 3 He detector banks placed at 75 cm from the centre of loaded hull cask comes out to 5.2 x 10 -3 counts per neutron (c/n) while with standard Pu-Be source placed in same position it comes out to be 3.1 x 10 3 c/n. The difference in the efficiency is mainly because of the differences in the geometry and size of hull cask as well as difference in the energy spectrum of hull waste and Pu-Be source. This is accounted through Monte Carlo computations. The Pu mass in solid waste comes out as expected and varies with the surface dose rate of drum in almost a proportional manner. Being simple and less time consuming, this setup has been installed for routine assay of solid Hull waste at NRB, Tarapur

  11. A Fast Algorithm of Convex Hull Vertices Selection for Online Classification.

    Science.gov (United States)

    Ding, Shuguang; Nie, Xiangli; Qiao, Hong; Zhang, Bo

    2018-04-01

    Reducing samples through convex hull vertices selection (CHVS) within each class is an important and effective method for online classification problems, since the classifier can be trained rapidly with the selected samples. However, the process of CHVS is NP-hard. In this paper, we propose a fast algorithm to select the convex hull vertices, based on the convex hull decomposition and the property of projection. In the proposed algorithm, the quadratic minimization problem of computing the distance between a point and a convex hull is converted into a linear equation problem with a low computational complexity. When the data dimension is high, an approximate, instead of exact, convex hull is allowed to be selected by setting an appropriate termination condition in order to delete more nonimportant samples. In addition, the impact of outliers is also considered, and the proposed algorithm is improved by deleting the outliers in the initial procedure. Furthermore, a dimension convention technique via the kernel trick is used to deal with nonlinearly separable problems. An upper bound is theoretically proved for the difference between the support vector machines based on the approximate convex hull vertices selected and all the training samples. Experimental results on both synthetic and real data sets show the effectiveness and validity of the proposed algorithm.

  12. Lightweight hull surface self-design vertical parameterization method based on NURBS

    Directory of Open Access Journals (Sweden)

    ZHANG Yanru

    2017-10-01

    Full Text Available [Objectives] At present, conventional design is limited to parent ship design space, and cannot drive ship hull design using as few parameters as possible. In order to solve the above problems, [Methods] by combining the draught function with NURBS, a ship hull surface self-design method based on vertical parameterization is proposed. In this method, the waterline is designated as the basic design unit; the bottom flat end line, designed waterline, stem and stern contours, side flat end line and maximum section line are designated as the characteristic constraints of the ship hull; and the draught function values corresponding to the characteristic parameters are designated as the design objectives. In this way, a waterline approximation model is built, and an evolutionary algorithm can be used to solve the approximation model. Finally, the ship hull surface is generated on the basis of the waterline using the NURBS skinning technique.[Results] The design examples of the characteristic curves of the full-scale ship hull surface indicate the practicable and advanced nature of this method.[Conclusions] The hull surface can be designed with as little data as possible using this method, making it much more suitable for the self-design of new ship forms.

  13. Ingestive Behavior and Nitrogen Balance of Confined Santa Ines Lambs Fed Diets Containing Soybean Hulls

    Directory of Open Access Journals (Sweden)

    Milena Patrícia Viana Bastos

    2014-01-01

    Full Text Available The objective of this study was to assess the effect of substituting corn with soybean hulls on the ingestive behavior and nitrogen balance of Santa Ines lambs. A total of 25 lambs with an initial body weight of 20±2 kg at approximately six months of age, sheltered individually in stalls (1.10 m×1.0 m, considering an entirely casual experimental delineation. Soybean hulls were substituted for corn at 0, 250, 500, 750, and 1,000 g/kg of dry matter (DM. The time spent feeding, ruminating, masticating, and resting was not affected by the substitution of corn with soybean hulls. In fact, the feeding efficiency in g DM/h and the rumination efficiency in g DM/bolus increased linearly with soybean hull substitution in the feed. Although the nitrogen balance was not altered by the use of soybean hulls as a substitute for corn in the diets of Santa Ines lambs, the N ingested and N digested expressed in g/d, N retained as a percentage of that ingested, and N retained as a percentage of that digested displayed quadratic behavior. In conclusion, corn can be substituted with soybean hulls up to 1,000 g/kg of dry matter in the concentrate, without changing the ingestive behavior and nitrogen balance.

  14. Ingestive behavior and nitrogen balance of confined santa ines lambs fed diets containing soybean hulls.

    Science.gov (United States)

    Bastos, Milena Patrícia Viana; de Carvalho, Gleidson Giordano Pinto; Pires, Aureliano José Vieira; Silva, Robério Rodrigues; Filho, Antônio Eustáquio; Dos Santos, Edileusa de Jesus; Chagas, Daiane Maria Trindade; Barroso, Daniele Soares; Filho, George Abreu

    2014-01-01

    The objective of this study was to assess the effect of substituting corn with soybean hulls on the ingestive behavior and nitrogen balance of Santa Ines lambs. A total of 25 lambs with an initial body weight of 20±2 kg at approximately six months of age, sheltered individually in stalls (1.10 m×1.0 m), considering an entirely casual experimental delineation. Soybean hulls were substituted for corn at 0, 250, 500, 750, and 1,000 g/kg of dry matter (DM). The time spent feeding, ruminating, masticating, and resting was not affected by the substitution of corn with soybean hulls. In fact, the feeding efficiency in g DM/h and the rumination efficiency in g DM/bolus increased linearly with soybean hull substitution in the feed. Although the nitrogen balance was not altered by the use of soybean hulls as a substitute for corn in the diets of Santa Ines lambs, the N ingested and N digested expressed in g/d, N retained as a percentage of that ingested, and N retained as a percentage of that digested displayed quadratic behavior. In conclusion, corn can be substituted with soybean hulls up to 1,000 g/kg of dry matter in the concentrate, without changing the ingestive behavior and nitrogen balance.

  15. Hot springs in Hokuriku District

    Energy Technology Data Exchange (ETDEWEB)

    Sato, K. (Hot Springs Research Center, Japan)

    1971-01-01

    In the Hokuriku district including Toyama, Ishikawa, and Fukui Prefectures, hot springs of more than 25/sup 0/C were investigated. In the Toyama Prefecture, there are 14 hot springs which are located in an area from the Kurobe River to the Tateyama volcano and in the mountainous area in the southwest. In Ishikawa Prefecture there are 16 hot springs scattered in Hakusan and its vicinity, the Kaga mountains, and in the Noto peninsula. In northern Fukui Prefecture there are seven hot springs. The hot springs in Shirakawa in Gifu Prefecture are characterized as acid springs producing exhalations and H/sub 2/S. These are attributed to the Quaternary volcanoes. The hot springs of Wakura, Katayamazu, and Awara in Ishikawa Prefecture are characterized by a high Cl content which is related to Tertiary andesite. The hot springs of Daishoji, Yamanaka, Yamashiro, Kuritsu, Tatsunokuchi, Yuwaku, and Yunotani are characterized by a low HCO/sub 3/ content. The Ca and SO/sub 4/ content decreases from east to west, and the Na and Cl content increases from west to east. These fluctuations are related to the Tertiary tuff and rhyolite. The hot springs of Kuronagi, Kinshu, and Babadani, located along the Kurobe River are characterized by low levels of dissolved components and high CO/sub 2/ and HCO/sub 3/ content. These trends are related to late Paleozoic granite. Hot springs resources are considered to be connected to geothermal resources. Ten tables, graphs, and maps are provided.

  16. Weldon Spring dose calculations

    International Nuclear Information System (INIS)

    Dickson, H.W.; Hill, G.S.; Perdue, P.T.

    1978-09-01

    In response to a request by the Oak Ridge Operations (ORO) Office of the Department of Energy (DOE) for assistance to the Department of the Army (DA) on the decommissioning of the Weldon Spring Chemical Plant, the Health and Safety Research Division of the Oak Ridge National Laboratory (ORNL) performed limited dose assessment calculations for that site. Based upon radiological measurements from a number of soil samples analyzed by ORNL and from previously acquired radiological data for the Weldon Spring site, source terms were derived to calculate radiation doses for three specific site scenarios. These three hypothetical scenarios are: a wildlife refuge for hunting, fishing, and general outdoor recreation; a school with 40 hr per week occupancy by students and a custodian; and a truck farm producing fruits, vegetables, meat, and dairy products which may be consumed on site. Radiation doses are reported for each of these scenarios both for measured uranium daughter equilibrium ratios and for assumed secular equilibrium. Doses are lower for the nonequilibrium case

  17. Spring viremia of carp

    Science.gov (United States)

    Ahne, W.; Bjorklund, H.V.; Essbauer, S.; Fijan, N.; Kurath, G.; Winton, J.R.

    2002-01-01

    pring viremia of carp (SVC) is an important disease affecting cyprinids, mainly common carp Cyprinus carpio. The disease is widespread in European carp culture, where it causes significant morbidity and mortality. Designated a notifiable disease by the Office International des Epizooties, SVC is caused by a rhabdovirus, spring viremia of carp virus (SVCV). Affected fish show destruction of tissues in the kidney, spleen and liver, leading to hemorrhage, loss of water-salt balance and impairment of immune response. High mortality occurs at water temperatures of 10 to 17°C, typically in spring. At higher temperatures, infected carp develop humoral antibodies that can neutralize the spread of virus and such carp are protected against re-infection by solid immunity. The virus is shed mostly with the feces and urine of clinically infected fish and by carriers. Waterborne transmission is believed to be the primary route of infection, but bloodsucking parasites like leeches and the carp louse may serve as mechanical vectors of SVCV. The genome of SVCV is composed of a single molecule of linear, negative-sense, single-stranded RNA containing 5 genes in the order 3¹-NPMGL-5¹ coding for the viral nucleoprotein, phosphoprotein, matrix protein, glycoprotein, and polymerase, respectively. Polyacrylamide gel electrophoresis of the viral proteins, and sequence homologies between the genes and gene junctions of SVCV and vesicular stomatitis viruses, have led to the placement of the virus as a tentative member of the genus Vesiculovirus in the family Rhabdoviridae. These methods also revealed that SVCV is not related to fish rhabdoviruses of the genus Novirhabdovirus. In vitro replication of SVCV takes place in the cytoplasm of cultured cells of fish, bird and mammalian origin at temperatures of 4 to 31°C, with an optimum of about 20°C. Spring viremia of carp can be diagnosed by clinical signs, isolation of virus in cell culture and molecular methods. Antibodies directed

  18. [Skull vibratory test in partial vestibular lesions--influence of the stimulus frequency on the nystagmus direction].

    Science.gov (United States)

    Dumas, G; Perrin, P; Morel, N; N'Guyen, D Q; Schmerber, S

    2005-01-01

    Results of the skull vibratory test (SVT) in partial unilateral vestibular peripheral lesions (PUVL) are different from the results in total vestibular lesions (TUVL). To reveal a correlation between the results of the analysis of the skull vibratory nystagmus (SVN) horizontal component and the side of the lesion; to correlate these results with the stimulus frequency. To find out a predictive correlation between the SVN horizontal and vertical components and the topography of a vestibular lesion. To appreciate the degree of vestibular deafferentation (extended to high frequencies) provoked by gentamicin labyrinthectomy and its efficiency in Meniere's disease. 53 patients with a SVN and a PUVL were included and compared with 10 TUVL and 10 normal subjects. Protocol included a HST (2 Hz), a SVT at 30, 60 and 100 Hz and a caloric test. Recordings were performed with a 2D and 3D VNG device. In PUVL, SVN at 30, 60 and 100 Hz was obtained in 80, 90 and 90% of cases respectively. SVN is correlated with the side of the lesion at 30, 60 and 100 Hz respectively in 65%, 63%, 80% of cases. SVN is not correlated with the side of the lesion in 20% of Meniere's disease, in 8% of vestibular neuritis and in 6% of vestibular schwannoma. In PUVL HSN is correlated with the side of the lesion in 69% of cases. The direction of the HSN and of the SVN was different in 23% when the nystagmus attended at the same time for both tests. In PUVL the direction of the SVN is different at 100 Hz and 30 Hz in 16% of cases when they are concomittant on the same patient. After Gentamicine labyrinthectomy, the coherence of the results in caloric test, HSN and SVN (areflexy and lesional nystagmus beating toward the safe side) was correlated with the efficiency of the therapy. A SVN vertical component was met in 10% of PUVL (essentially in anterior canal dehiscence and few cases of partial labyrinthitis). The horizontal SVN SPV is significantly slower in PUVL than in TUVL patients (p=0.0004). The SVT

  19. Developing bulk exchange spring magnets

    Science.gov (United States)

    Mccall, Scott K.; Kuntz, Joshua D.

    2017-06-27

    A method of making a bulk exchange spring magnet by providing a magnetically soft material, providing a hard magnetic material, and producing a composite of said magnetically soft material and said hard magnetic material to make the bulk exchange spring magnet. The step of producing a composite of magnetically soft material and hard magnetic material is accomplished by electrophoretic deposition of the magnetically soft material and the hard magnetic material to make the bulk exchange spring magnet.

  20. Evaluation of peanut hulls as an alternative to bleaching clays

    Energy Technology Data Exchange (ETDEWEB)

    Hassanein, M. M.; El-Shami, S. M.; Taha, F. S.

    2011-07-01

    Peanut hulls (PNH) were carbonized at different temperatures, times, and evaluated at different concentrations as an alternative to bleaching clays. Evaluation of bleached crude soybean oil with PNH was based on their delta free fatty acids, reduction in peroxide value (PV), reduction in phospholipids (PL) and bleachability. The performance of several commercially used bleaching clays was evaluated, for comparison. Mixtures were formulated including: PNH and Tonsil -N (TN), PNH and Fuller's earth (FE) and PNH and O-passive (OP) and examined. The oxidative stability of oils was determined. Results for the investigated commercial bleaching clays revealed: TN > FE > F > TF > OP. Highest reduction in PV and PL, and highest bleachability were achieved for soybean oil bleached with 2% PNH carbonized at 500 degree centigrade for 30 min (PNH). Mixtures of PNH with the three chosen bleaching clays indicated that 1PNH : 2TN gave the highest bleachability. CSO was miscella bleached in hexane using PNH and resulted in an appreciable improvement in all oil characteristics, especially in bleachability. Oxidative stability of oils was in the following order: TN > control > FE > PNH with Induction period values of 23.1 > 6.43 > 5.73 > 2.85 h, respectively. (Author) 20 refs.

  1. Metal ion removal from aqueous solution using physic seed hull.

    Science.gov (United States)

    Mohammad, Masita; Maitra, Saikat; Ahmad, Naveed; Bustam, Azmi; Sen, T K; Dutta, Binay K

    2010-07-15

    The potential of physic seed hull (PSH), Jantropha curcas L. as an adsorbent for the removal of Cd(2+) and Zn(2+) metal ions from aqueous solution has been investigated. It has been found that the amount of adsorption for both Cd(2+) and Zn(2+) increased with the increase in initial metal ions concentration, contact time, temperature, adsorbent dosage and the solution pH (in acidic range), but decreased with the increase in the particle size of the adsorbent. The adsorption process for both metal ions on PSH consists of three stages-a rapid initial adsorption followed by a period of slower uptake of metal ions and virtually no uptake at the final stage. The kinetics of metal ions adsorption on PSH followed a pseudo-second-order model. The adsorption equilibrium data were fitted in the three adsorption isotherms-Freundlich, Langmuir and Dubinin-Radushkevich isotherms. The data best fit in the Langmuir isotherm indication monolayer chemisorption of the metal ions. The adsorption capacity of PSH for both Zn(2+) and Cd(2+) was found to be comparable with other available adsorbents. About 36-47% of the adsorbed metal could be leached out of the loaded PSH using 0.1M HCl as the eluting medium. 2010 Elsevier B.V. All rights reserved.

  2. Zeolite and wollastonite synthesis from rice hull ash

    International Nuclear Information System (INIS)

    Fernandes, Alberto de Andrade

    2006-01-01

    Rice hull ash (RHA) is a industry scrap rich in amorphous silica. A simple and low-energy cost method for the extraction of this silica was researched. A low level of impurity and high reactivity material was produced, which is appropriate for the synthesis of zeolites and wollastonite (CaSiO 3 ). The synthetic zeolites has not similar structures in nature, and they have been more and more valued in the market due to their purity and efficiency in specific applications like ion exchange, molecular sieve and catalysis areas. High purity wollastonite has many applications in manufacturing and agriculture. The mineral wollastonite can be formed in nature in different ways; it is generally accepted two forming processes, both encompassing limestone metamorphism (heat and pressure). In this work, a new process for the synthesis of zeolites and wollastonite from RHA colloidal silica was developed. Moreover, the process is aimed at lower energy costs, fewer stages and fewer reactants consume. In this work, zeolite A used in detergent and zeolite ZSM-5, employed in the petrochemical industry due to its high selectivity in catalytic reactions and its high thermo and acid stability, were synthesized. The first step of the wollastonite synthesis was studied, with the purpose of obtaining calcium hydrosilicate. Eleven different hydrosilicates occur in the system Ca(OH) 2 -SiO 2 -H 2 O, in the second step it was annealed to form the wollastonite phase. (author)

  3. Spring security 3.x cookbook

    CERN Document Server

    Mankale, Anjana

    2013-01-01

    This book follows a cookbook style exploring various security solutions provided by Spring Security for various vulnerabilities and threat scenarios that web applications may be exposed to at the authentication and session level layers.This book is for all Spring-based application developers as well as Java web developers who wish to implement robust security mechanisms into web application development using Spring Security.Readers are assumed to have a working knowledge of Java web application development, a basic understanding of the Spring framework, and some knowledge of the fundamentals o

  4. A method for assessing the regional vibratory pattern of vocal folds by analysing the video recording of stroboscopy.

    Science.gov (United States)

    Lee, J S; Kim, E; Sung, M W; Kim, K H; Sung, M Y; Park, K S

    2001-05-01

    Stroboscopy and kymography have been used to examine the motional abnormality of vocal folds and to visualise their regional vibratory pattern. In a previous study (Laryngoscope, 1999), we introduced the conceptual idea of videostrobokymography, in which we applied the concept of kymography on the pre-recorded video images using stroboscopy, and showed its possible clinical application to various disorders in vocal folds. However, a more detailed description about the software and the mathematical formulation used in this system is needed for the reproduction of similar systems. The composition of hardwares, user-interface and detail procedures including mathematical equations in videostrobokymography software is presented in this study. As an initial clinical trial, videostrobokymography was applied to the preoperative and postoperative videostroboscopic images of 15 patients with Reinke's edema. On preoperative examination, videostrobokymograms showed irregular pattern of mucosal wave and, in some patients, a relatively constant glottic gap during phonation. After the operation, the voice quality of all patients was improved in acoustic and aerodynamic assessments, and videostrobokymography showed clearly improved mucosal waves (change in open quotient: mean +/- SD= 0.11 +/- 0.05).

  5. Further Examination of the Vibratory Loads Reduction Results from the NASA/ARMY/MIT Active Twist Rotor Test

    Science.gov (United States)

    Wilbur, Matthew L.; Yeager, William T., Jr.; Sekula, Martin K.

    2002-01-01

    The vibration reduction capabilities of a model rotor system utilizing controlled, strain-induced blade twisting are examined. The model rotor blades, which utilize piezoelectric active fiber composite actuators, were tested in the NASA Langley Transonic Dynamics Tunnel using open-loop control to determine the effect of active-twist on rotor vibratory loads. The results of this testing have been encouraging, and have demonstrated that active-twist rotor designs offer the potential for significant load reductions in future helicopter rotor systems. Active twist control was found to use less than 1% of the power necessary to operate the rotor system and had a pronounced effect on both rotating- and fixed-system loads, offering reductions in individual harmonic loads of up to 100%. A review of the vibration reduction results obtained is presented, which includes a limited set of comparisons with results generated using the second-generation version of the Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics (CAMRAD II) rotorcraft comprehensive analysis.

  6. [Relationship between vibratory sense threshold and blood lead concentration in ceramic color workers and transfer printing manufacturers].

    Science.gov (United States)

    Fukaya, Y; Matsumoto, T; Fujiwara, N; Tokudome, S

    1995-08-01

    We measured vibratory sense thresholds (VSTs) at 63Hz and 125Hz on the third fingertip of the right hand and on the third toe of the right foot of 74 male workers. The subjects were workers engaged in manufacturing ceramic color and transfer printing paper, whose blood lead (Pb-B) levels were 2-58 micrograms/dl. They were divided into three groups according to the Pb-B levels, namely, below 9, 10-19, and 20 micrograms/dl or more. For statistical analysis, simple and partial correlations, and Scheffé's multiple comparison between the least squares means were used. The VSTs on the fingertip as well as on the toe showed a significant correlation with age. The VSTs at 125Hz on the fingertip were also significantly correlated with alcohol consumption and cigarette smoking. Controlling for age, systolic blood pressure, alcohol consumption and smoking habit, a significant dose-effect relationship was observed between the VSTs at not only 63Hz but at 125Hz on the fingertip, and each of the corresponding Pb-B levels. A similar tendency was also observed at the two frequencies on the toe. The measurement of VSTs was considered to be an effective screening test for sensory nerve disorders caused by lead poisoning.

  7. Theory of vibratory mobilization and break-up of non-wetting fluids entrapped in pore constrictions

    Science.gov (United States)

    Beresnev, I.; Li, W.; Vigil, D.

    2006-12-01

    Quantitative dynamics of a non-wetting (e. g., NAPL) ganglion entrapped in a pore constriction and subjected to vibrations can be approximated by the equation of motion of an oscillator moving under the effect of the external pressure gradient, inertial oscillatory force, and restoring capillary force. The solution of the equation provides the conditions under which the droplet experiences forced oscillations without being mobilized or is liberated upon the acceleration of the wall exceeding an "unplugging" threshold. This solution provides a quantitative tool for the estimation of the parameters of vibratory fields needed to liberate entrapped non-wetting fluids. For typical pore sizes encountered in reservoirs and aquifers, wall accelerations must exceed at least several m/sec2 and even higher levels to mobilize the droplets of NAPL; however, in the populations of ganglia entrapped in natural porous environments, many may reside very near their mobilization thresholds and may be mobilized by extremely low accelerations as well. For given acceleration, lower seismic frequencies are more efficient. The ganglia may also break up into smaller pieces when passing through pore constrictions. The snap-off is governed by the geometry only; for constrictions with sinusoidal profile (spatial wavelength of L and maximum and minimum radii of rmax and rmin, the break-up occurs if L > 2π(rmin rmax)1/2. Computational fluid dynamics shows the details of the break-up process.

  8. Spheres of discharge of springs

    Science.gov (United States)

    Springer, Abraham E.; Stevens, Lawrence E.

    2009-02-01

    Although springs have been recognized as important, rare, and globally threatened ecosystems, there is as yet no consistent and comprehensive classification system or common lexicon for springs. In this paper, 12 spheres of discharge of springs are defined, sketched, displayed with photographs, and described relative to their hydrogeology of occurrence, and the microhabitats and ecosystems they support. A few of the spheres of discharge have been previously recognized and used by hydrogeologists for over 80 years, but others have only recently been defined geomorphologically. A comparison of these spheres of discharge to classification systems for wetlands, groundwater dependent ecosystems, karst hydrogeology, running waters, and other systems is provided. With a common lexicon for springs, hydrogeologists can provide more consistent guidance for springs ecosystem conservation, management, and restoration. As additional comprehensive inventories of the physical, biological, and cultural characteristics are conducted and analyzed, it will eventually be possible to associate spheres of discharge with discrete vegetation and aquatic invertebrate assemblages, and better understand the habitat requirements of rare or unique springs species. Given the elevated productivity and biodiversity of springs, and their highly threatened status, identification of geomorphic similarities among spring types is essential for conservation of these important ecosystems.

  9. Spring valve for well completion

    Energy Technology Data Exchange (ETDEWEB)

    Gorbatov, P T

    1966-07-22

    A spring-loaded valve for well completion consists of a housing with a spring-loaded closing element. In order to protect the closing element from corrosion which might lower the pressure drop, the closing element is made in the form of a piston. It is tightly connected with sealing elements. The housing has orifices, overlapping the piston in the initial position.

  10. Experimenting with Inexpensive Plastic Springs

    Science.gov (United States)

    Perez, Leander; Marques, Adriana; Sánchez, Iván

    2014-01-01

    Acommon undergraduate laboratory experience is the determination of the elastic constant of a spring, whether studying the elongation under a static load or studying the damped harmonic motion of the spring with a suspended mass. An alternative approach to this laboratory experience has been suggested by Menezes et al., aimed at studying the…

  11. Lessons from the Contraceptive CHOICE Project: The Hull LARC Initiative

    Science.gov (United States)

    Trussell, James; Guthrie, Kate

    2014-01-01

    Aim To discover whether a hand-out explaining the benefits of intrauterine contraceptives (IUCs) and implants could increase their uptake in Hull, UK. Methods We developed a simple double-sided A4 hand-out. On one side was a script with pictures of copper and levonorgestrel IUCs beside a 20-pence coin and of an implant beside a hairgrip. On the other side was the three-tiered effectiveness chart published in the textbook Contraceptive Technology. We implemented the project in family planning (FP), abortion and antenatal clinics and GP practices. The plan was that the receptionist would give the hand-out to every woman and ask her to read it before seeing a clinician. We evaluated it in FP clinics and GP practices because routine electronic monitoring reports were available only for these. Results There was no impact in GP practices. There was no overall impact in FP clinics, with the exception of the service hub, in which there was an increase in the proportion of women receiving IUCs or implants of 15.0% between the periods October 2011-April 2012 and May 2012-November 2012 (p=0.0002). This clinic is open on six days per week and has permanent sexual health staff on the reception desk. Impact fell when a change in clinic procedure. The proportion returned to baseline in December 2012-November 2013, when a change in clinic procedure to reduce waiting times caused staff to stop dispensing handouts. Conclusion This was not a formal study, so there was no research coordinator to monitor the project. We think there was no impact among GPs because the project was never implemented by them. The project was poorly implemented at the four satellite FP clinics. Only the service hub implemented the project, where it had a clear impact. We conclude that when implemented as intended this simple extremely low-cost LARC intervention was highly effective and also extremely cost effective. PMID:25236471

  12. Roasted sesame hulls improve broiler performance without affecting carcass characteristics

    Directory of Open Access Journals (Sweden)

    Kamel Z. Mahmoud

    2015-09-01

    Full Text Available An experiment was conducted to evaluate the effect of using graded levels of roasted sesame hulls (RSH on growth performance and meat quality characteristics in broiler chickens. A total of 360 day-old Lohmann chicks were randomly allocated into 24 floor pens and raised over 42 days. One of four dietary treatments was assigned to each group of six pens in a completely randomized fashion. The chicks in the control group were fed a corn-soybean based diet (RSH-0, while the chicks in treatments two, three, and four were fed graded levels of RSH at 4% (RSH-4, 8% (RSH-8, and 12% (RSH-12, respectively. Diets were formulated to meet broiler chicks’ requirements according to the National Research Council for both starter and finisher rations. The results showed that RSH inclusion increased (P<0.05 feed intake and final body weight without adversely affecting the feed conversion ratio. Broiler chicks fed RSH-12 had heavier (P<0.05 breast and leg cuts compared to the control-fed group with no change to their chemical composition. Water holding capacity (WHC, cooking loss (CL, and shear force (SF reported similar results in all dietary groups. The chemical composition of both thigh and breast cuts was not affected by the RSH. After one day of thawing, colour coordinates of breast cuts behaved similarly in all dietary groups. The results of this study suggest that the addition of RSH to broiler diets up to 12% improves their growth performance; nevertheless, carcass characteristics and meat quality showed no alterations compared to the control-fed group.

  13. Effect of ship hull form on the resistance penalty from biofouling.

    Science.gov (United States)

    Oliveira, Dinis; Larsson, Ann I; Granhag, Lena

    2018-03-01

    Hull biofouling is a well-known problem for the shipping industry, leading to increased resistance and fuel consumption. Considering that the effects of hull form on resistance are known to be higher for a less slender hull, it is hypothesised in this paper that the effect of biofouling roughness on resistance is also dependent on the hull form. To test this hypothesis, previously reported full-scale numerical results on a containership are re-analysed. Form effects on roughness penalties, corresponding to K ΔCT  = 0.058 ± 0.025, are observed at a low speed (19 knots, Re s  = 2.29 × 10 9 ), which are however cancelled out by traditionally neglected roughness effects on wave-making resistance at a higher speed (24 knots, Re s  = 2.89 × 10 9 ). It is concluded that hull form effects on biofouling penalties can be significant at low speeds, though not generalisable for higher speeds, namely when wave-making resistance corresponds to ≥ 29% of total resistance.

  14. Characterization of whole assembly hulls produced by industrial reprocessing of LWR fuels

    International Nuclear Information System (INIS)

    Gue, J.P.; Isaac, M.

    1987-03-01

    The characterization program for Obrigheim and Stade PWR hulls sampled at La Hague was conducted in the CEA hot cells (Coquenstock program operating on whole assembly hulls). A description of the appearance of these hulls, recovered on the industrial scale and after severe damage, is followed by a review of the results of the different radiochemical characterization operations (neutron emission measurements, gamma scanning, alpha and mass spectrometry after dissolution of several samples, determination of the retention of tritium and other gaseous fission products occluded in the zircalloy clads etc). The alpha contamination of these hulls proved to be rather high, but it demonstrated that a large part (90 to 95%) was labile and could be removed by simple rinsing with cold 3N nitric acid. By contrast, contamination by fission products such as Cs 137, Ce 144 and Eu 154, remains high and relatively unaffected by nitriacid rinsing. Based on the results obtained and the observations recorded, an analysis is carried out of the origins of alpha contamination of these hulls treated on an industrial scale, among which the chief source is certainly the limited effectiveness of rinsing

  15. Characterization of whole assembly hulls produced by industrial reprocessing of LWR fuels

    International Nuclear Information System (INIS)

    Gue, J.P.; Isaac, M.; Hebel, W.

    1987-01-01

    The characterization program for Obrigheim and Stade PWR hulls sampled at La Hague was conducted in the CEA hot cells (Coquenstock program operating on whole assembly hulls). A description of the appearance of these hulls, recovered on the industrial scale and after severe damage, is followed by a review of the results of the different radiochemical characterization operations (neutron emission measurements, gamma scanning, alpha and mass spectrometry after dissolution of several samples, determination of the retention of tritium and other gaseous fission products occluded in the zircalloy clads, etc.). The alpha contamination of these hulls proved to be rather high, but it demonstrated that a large part (90 to 95%) was labile and could be removed by simple rinsing with cold 3N nitric acid. By contrast, contamination by fission products such as Cs 137, Ce 144 and Eu 154, remains high and relatively unaffected by nitric acid rinsing. Based on the results obtained and the observations recorded, an analysis is carried out of the origins of alpha contamination of these hulls treated on an industrial scale, among which the chief source is certainly the limited effectiveness of rinsing

  16. Genetic Analysis and Mapping of TWH Gene in Rice Twisted Hull Mutant

    Directory of Open Access Journals (Sweden)

    Jin-bo LI

    2009-03-01

    Full Text Available A mutant with twisted hulls was found in a breeding population of rice (Oryza sativa L.. The mutant shows less grain weight and inferior grain quality in addition to twisted hulls. Genetic analysis indicated that the phenotype of mutant was controlled by a single recessive gene (temporarily designated as TWH. To map the TWH gene, an F2 population was generated by crossing the twh mutant to R725, an indica rice variety with normal hulls. For bulked segregant analysis, the bulk of mutant plants was prepared by mixing equal amount of plant tissue from 10 twisted-hull plants and the bulk of normal plants was obtained by pooling equal amount tissue of 10 normal-hull plants. Two hundred and seven pairs of simple sequence repeat (SSR primers, which are distributed on 12 rice chromosomes, were used for polymorphism analysis of the parents and the two bulks. The TWH locus was initially mapped close to the SSR marker RM526 on chromosome 2. Therefore, further mapping was performed using 50 pairs of SSR primers around the marker RM526. The TWH was delimited between the SSR markers RM14128 and RM208 on the long arm of chromosome 2 at the genetic distances of 1.4 cM and 2.7 cM, respectively. These results provide the foundation for further fine mapping, cloning and functional analysis of the TWH gene.

  17. Nondestructive determination of residual fuel on leached hulls and dissolver sludges from LWR fuel reprocessing

    International Nuclear Information System (INIS)

    Wuerz, H.; Wagner, K.; Becker, H.J.

    1990-01-01

    In reprocessing plants leached hulls and dissolver sludges represent rather important intermediate level α-waste streams. A control of the Pu content of these waste streams is desirable. The nondestructive assay method to be preferred would be passive neutron counting. However, before any decision on passive neutron monitoring becomes possible a characterization of hulls and sludges in terms of Pu content and neutron emission is necessary. For the direct determination of plutonium on hulls and in sludges, as coming from reprocessing, an active neutron measurement is required. A simple, and sufficiently sensitive active neutron method which can easily be installed uses as stationary Cf-252 neutron source. This method was used for the characterization of hulls and sludges in terms of plutonium content and total neutron emission in the WAK. Meanwhile a total of 28 batches of leached hulls and 22 batches of dissolver sludges from reprocessing of PWR fuel have been assayed. The paper describes the assay method used and gives an analysis of the error sources together with a discussion of the results and the accuracies obtained in a reprocessing plant. (orig./HP)

  18. Effects of Hull Scratching, Soaking, and Boiling on Antinutrients in Japanese Red Sword Bean (Canavalia gladiata).

    Science.gov (United States)

    Une, Satsuki; Nonaka, Koji; Akiyama, Junich

    2016-10-01

    The effects of hull processing, soaking, and boiling on the content or activity of antinutrients in the red sword bean (RSB; Canavalia gladiata) were investigated. RSB seeds were compared with kidney bean (KB; Phaseolus vulgaris) seeds that are starch based and often used as processed products in Japan. RSB seeds had higher weight, thicker hull, and higher protein content, but lower moisture content compared with KB seeds. Because of the strong and thick hull, the relative water absorption of untreated RSB seeds was very low after soaking. Seeds were soaked after dehulling, scratching, and roasting. The results showed that hull scratching was the optimal method for increasing water absorption during soaking compared with dehulling and roasting. After soaking, the water used for soaking was discarded, since it had a high content of polyphenols and bitter taste, and RSB seeds were boiled in fresh water for 20, 40, and 60 min. The results showed that polyphenol and tannin contents, antioxidant activity, and hemagglutinating activity, as well as maltase, sucrase, and trypsin inhibitor activities in scratched RSB seeds decreased significantly after boiling compared with those in raw seeds, whereas amylase inhibitor activity showed no significant change. Overall, it was concluded that the combination of hull scratching, soaking, and boiling in fresh water can reduce thermal-stable or sensitive antinutrients in RSB and thus, significantly improve its nutritional value. © 2016 Institute of Food Technologists®.

  19. Macroalgal Introductions by Hull Fouling on Recreational Vessels: Seaweeds and Sailors

    Science.gov (United States)

    Mineur, Frédéric; Johnson, Mark P.; Maggs, Christine A.

    2008-10-01

    Macroalgal invasions in coastal areas have been a growing concern during the past decade. The present study aimed to assess the role of hull fouling on recreational yachts as a vector for macroalgal introductions. Questionnaire and hull surveys were carried out in marinas in France and Spain. The questionnaires revealed that the majority of yacht owners are aware of seaweed introductions, usually undertake short range journeys, dry dock their boat at least once a year, and use antifouling paints. The hull survey showed that many in-service yachts were completely free of macroalgae. When present, fouling assemblages consisted mainly of one to two macroalgal species. The most commonly found species was the tolerant green seaweed Ulva flexuosa. Most of the other species found are also cosmopolitan and opportunistic. A few nonnative and potentially invasive Ceramiales (Rhodophyta) were found occasionally on in-service yachts. On the basis of the information gathered during interviews of yacht owners in the surveyed area, these occurrences are likely to be uncommon. However they can pose a significant risk of primary or secondary introductions of alien macroalgal species, especially in the light of the increase in yachting activities. With large numbers of recreational yachts and relatively rare occurrences of nonnative species on hulls, comprehensive screening programs do not seem justified or practical. The risks of transferring nonnative species may, however, be minimized by encouraging the behaviors that prevent fouling on hulls and by taking action against neglected boats before they can act as vectors.

  20. Linear magnetic spring and spring/motor combination

    Science.gov (United States)

    Patt, Paul J. (Inventor); Stolfi, Fred R. (Inventor)

    1991-01-01

    A magnetic spring, or a spring and motor combination, providing a linear spring force characteristic in each direction from a neutral position, in which the spring action may occur for any desired coordinate of a typical orthogonal coordinate system. A set of magnets are disposed, preferably symmetrically about a coordinate axis, poled orthogonally to the desired force direction. A second set of magnets, respectively poled opposite the first set, are arranged on the sprung article. The magnets of one of the sets are spaced a greater distance apart than those of the other, such that an end magnet from each set forms a pair having preferably planar faces parallel to the direction of spring force, the faces being offset so that in a neutral position the outer edge of the closer spaced magnet set is aligned with the inner edge of the greater spaced magnet set. For use as a motor, a coil can be arranged with conductors orthogonal to both the magnet pole directions and the direction of desired spring force, located across from the magnets of one set and fixed with respect to the magnets of the other set. In a cylindrical coordinate system having axial spring force, the magnets are radially poled and motor coils are concentric with the cylinder axis.

  1. A bountiful spring harvest

    CERN Multimedia

    2013-01-01

    Although we recently put the clocks forward and spring has officially begun, the view from my window looks more autumnal – befitting of the season of mists and mellow fruitfulness, rather than that of sowing seeds for the future. Which, in a way is appropriate. With the LHC paused, we are reaping a kind of harvest in the form of recognition for our efforts.   Two weeks ago, I was in Edinburgh, on behalf of everyone at CERN, to collect the Edinburgh medal, which we shared with Peter Higgs. I particularly like the citation for this honour: “The Edinburgh Medal is awarded each year to men and women of science and technology whose professional achievements are judged to have made a significant contribution to the understanding and well-being of humanity.” I like this, because it underlines a fact that needs to be shouted louder – that fundamental science does more than build the sum of human knowledge, it is also the foundation of human well-being. A few d...

  2. Spring comes for ATLAS

    CERN Multimedia

    Butin, F.

    2004-01-01

    (First published in the CERN weekly bulletin 24/2004, 7 June 2004.) A short while ago the ATLAS cavern underwent a spring clean, marking the end of the installation of the detector's support structures and the cavern's general infrastructure. The list of infrastructure to be installed in the ATLAS cavern from September 2003 was long: a thousand tonnes of mechanical structures spread over 13 storeys, two lifts, two 65-tonne overhead travelling cranes 25 metres above cavern floor, with a telescopic boom and cradle to access the remaining 10 metres of the cavern, a ventilation system for the 55 000 cubic metre cavern, a drainage system, a standard sprinkler system and an innovative foam fire-extinguishing system, as well as the external cryogenic system for the superconducting magnets and the liquid argon calorimeters (comprising, amongst other things, two helium refrigeration units, a nitrogen refrigeration unit and 5 km of piping for gaseous or liquid helium and nitrogen), not to mention the handling eq...

  3. Active vibration control of smart hull structure using piezoelectric composite actuators

    International Nuclear Information System (INIS)

    Sohn, Jung Woo; Choi, Seung-Bok; Lee, Chul-Hee

    2009-01-01

    In this paper, active vibration control performance of the smart hull structure with macro-fiber composite (MFC) is evaluated. MFC is an advanced piezoelectric composite which has great flexibility and increased actuating performance compared to a monolithic piezoelectric ceramic patch. The governing equations of motion of the hull structure with MFC actuators are derived based on the classical Donnell–Mushtari shell theory. The actuating model for the interaction between hull structure and MFC is included in the governing equations. Subsequently, modal characteristics are investigated and compared with the results obtained from experiment. The governing equations of the vibration control system are then established and expressed in the state space form. A linear quadratic Gaussian (LQG) control algorithm is designed in order to effectively and actively control the imposed vibration. The controller is experimentally realized and vibration control performances are evaluated

  4. Static analysis of the hull plate using the finite element method

    Science.gov (United States)

    Ion, A.

    2015-11-01

    This paper aims at presenting the static analysis for two levels of a container ship's construction as follows: the first level is at the girder / hull plate and the second level is conducted at the entire strength hull of the vessel. This article will describe the work for the static analysis of a hull plate. We shall use the software package ANSYS Mechanical 14.5. The program is run on a computer with four Intel Xeon X5260 CPU processors at 3.33 GHz, 32 GB memory installed. In terms of software, the shared memory parallel version of ANSYS refers to running ANSYS across multiple cores on a SMP system. The distributed memory parallel version of ANSYS (Distributed ANSYS) refers to running ANSYS across multiple processors on SMP systems or DMP systems.

  5. Evaluation of alternative waste management schemes for LWR hulls and caps

    International Nuclear Information System (INIS)

    Chaudon, L.; Cecille, L.; Klein, M.; Kowa, S.; Mehling, O.; Thiels, G.

    1990-01-01

    LWR hulls and caps represent one of the major sources of α bearing solid waste generated in the nuclear fuel cycle. For this reason, the CEC launched a theoretical study to evaluate alternative schemes for the overall management of this waste. Both volume reduction techniques and α decontamination of the hulls were assessed. The study demonstrated that the transport and disposal of the conditioned waste in deep geological formations play a dominant part in the total management costs. Important cost savings can be achieved through the implementation of efficient volume reduction techniques, i.e. melting or compaction. As an alternative approach, exhaustive α decontamination of the hulls appears promising, provided that the conditioned waste can be made to comply with the disposal criteria of mines. Finally, prolongation of the interim storage period for the waste packages from 1 to 30 years may prove beneficial on the transport costs

  6. Study on the natural pigments present in the Hulls of Garcinia Mangostana Linn

    International Nuclear Information System (INIS)

    San Dar Aung; Aye Aye Tun; San San Aye; Maung Maung Htay

    2005-09-01

    Garcinia mangostana Linn,(Family; Guttiferae) is known to be a rich source of bioactive molecules including flavonoids, benzophenones and lactones. A variety of xanthones have been isolated from mangosteen plants and fruits include the hull, rind heartwood and flesh. The fruit hull is used as an astringent and also used against cholera, dysentery and diarrhoea in traditional medicinal system. Petroleum ether extraction of the dried and powered fruit hulls followed by column chromatographic separation afforded two compounds, namely, gartanin (1) (0.48% in yield, mp 146-152 ) and mangostin (2) (0.97% in yield, mp (179-180). The structures of these two compounds have been identified by UV, FT-IR, NMR and EIMS. These identifications were confirmed by comparison of melting point values with reported data in the literature

  7. Structural Health Monitoring of Tall Buildings with Numerical Integrator and Convex-Concave Hull Classification

    Directory of Open Access Journals (Sweden)

    Suresh Thenozhi

    2012-01-01

    Full Text Available An important objective of health monitoring systems for tall buildings is to diagnose the state of the building and to evaluate its possible damage. In this paper, we use our prototype to evaluate our data-mining approach for the fault monitoring. The offset cancellation and high-pass filtering techniques are combined effectively to solve common problems in numerical integration of acceleration signals in real-time applications. The integration accuracy is improved compared with other numerical integrators. Then we introduce a novel method for support vector machine (SVM classification, called convex-concave hull. We use the Jarvis march method to decide the concave (nonconvex hull for the inseparable points. Finally the vertices of the convex-concave hull are applied for SVM training.

  8. Treatment, conditioning and storage of solid alpha-bearing waste and cladding hulls. Paris, 5-7 December 1977

    International Nuclear Information System (INIS)

    1978-01-01

    A synthesis of the current practices and research and development work in the area of alpha-bearing waste and cladding hulls management is presented in 27 papers. After a review of national programmes, general management aspects of radioactive wastes are presented and different techniques are exposed, mainly incineration, volume reduction, conditioning concepts and cladding hulls

  9. Experimental investigation of ash deposits characteristics of co-combustion of coal and rice hull using a digital image technique

    International Nuclear Information System (INIS)

    Qiu, Kunzan; Zhang, Hailong; Zhou, Hao; Zhou, Bin; Li, Letian; Cen, Kefa

    2014-01-01

    This paper investigated the ash deposit characteristics during the co-firing Da Tong (DA) coal with different proportions of rice hull (0%, 5%, 10%, and 20%, based on weight) in a pilot-scale furnace. The growth of ash deposit with a four-stage mode was presented. The stable thickness values of DA coal, 5% rice hull, 10% rice hull, and 20% rice hull were 0.5, 1.4, 2.9, 5.7 cm, with stable heat flux values of 230, 200, 175, and 125 kW/m 2 , respectively. According to the results of scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), the amount of Si in the deposits increased with the increasing proportion of rice hull rich in SiO 2 . The X-ray diffraction (XRD) analysis results indicated that most elements except Si were in the amorphous state because of the formation of eutectics. The stable thicknesses of deposits increased exponentially with the proportion of rice hull. The deposit was loose, easy removable but it reduced the heat transfer significantly. Consequently, sootblowing timely was necessary when co-firing DA coal with rice hull. - Highlights: • Digital image technique was used to monitor deposits growth process. • A type of four stages mode of ash deposit growth was presented. • The heat flux of ash deposits fit a three-stage mode. • The addition of rice hull increased the porosity of deposits

  10. Cultivation of Podospora anserina on soybean hulls results in an efficient enzyme cocktail for plant biomass hydrolysis

    NARCIS (Netherlands)

    Mäkelä, Miia R; Bouzid, Ourdia; Ruiz-Robleto, J.; Post, Harm|info:eu-repo/dai/nl/341667374; Peng, Mao; Heck, Albert|info:eu-repo/dai/nl/105189332; Altelaar, Maarten|info:eu-repo/dai/nl/304833517; de Vries, Ronald P|info:eu-repo/dai/nl/186324960

    2017-01-01

    The coprophilic ascomycete fungus Podospora anserina was cultivated on three different plant biomasses, i.e. cotton seed hulls (CSH), soybean hulls (SBH) and acid-pretreated wheat straw (WS) for four days, and the potential of the produced enzyme mixtures was compared in the enzymatic

  11. The Begg's uprighting spring - Revisited.

    Science.gov (United States)

    Kumar, Vinay; Sundareswaran, Shobha

    2015-01-01

    Uprighting springs, an integral part of the Begg ligsht wire differential force technique is gaining more and more popularity, as a useful adjunct in contemporary preadjusted edgewise appliance systems as well. It can be used with brackets containing vertical slots for mesiodistal crown uprighting, or as braking auxiliaries providing additional anchorage while protracting posteriors. Here, we present a simple and quick chair side method of fabricating and customizing uprighting springs according to the required crown/root movement for correction. This communication would serve as a ready reckoner during fabrication of the springs, thus dispelling the confusion that usually arises regarding direction and position of the coil and active arm.

  12. Study on characteristics of spent PWR cladding hull for categorizing into Non-TRU waste

    International Nuclear Information System (INIS)

    Jung, In Ha; Kim, Jong Ho; Park, Jang Jin; Shin, Jin Myeong; Lee, Ho Hee; Yang, Myung Seung

    2005-01-01

    AFCI and GEN-IV programs aim for decreasing the high level radioactive wastes to be disposed. They also try to get valuable materials to recycle as resources such as uranium and plutonium. On the other hand, cladding hull expected to be one-thirds in volume of spent fuel assembly has not studied so much in the point view of recycling to reuse. Since traditional process of reprocessing was wet process, cladding hull generating through the reprocessing process was unavoidably contaminated with TRU by acid solvent during the process. Therefore, cladding hull has been classified into TRU wastes or high level wastes. According to the strategy for TRU high level radioactive wastes of USA as well as Korea, it regulates in two respects. One is activity and the other is heat generation. In respect of activity, TRU waste contains more than 100 nCi/kg of alpha emits with longer half life than 20 years and higher than 92 in atomic number. Also, wastes are categorized into TRU waste when it generates higher than 2kW/m3, in the respect of heat generation. Our results as well as literatures, almost all of TRU nuclides in the cladding hull are responsible for remained uranium and plutonium owing to pellet-cladding interaction. In addition, recoiled fission products on the surface of the cladding hull serve as heat generator. Up to now, decontamination of the cladding hull generating from the reprocessing of wet process is regarded as valueless and un-economic works owing to the amount of second waste produced

  13. CONSTRUCTION OF THE DISCRETE HULL FOR THE COMBINATORICS OF A REGULAR PENTAGONAL TILING OF THE PLANE

    DEFF Research Database (Denmark)

    Ramirez-Solano, Maria

    2016-01-01

    The article A “regular” pentagonal tiling of the plane by P. L. Bowers and K. Stephenson, Conform. Geom. Dyn. 1, 58–86, 1997, defines a conformal pentagonal tiling. This is a tiling of the plane with remarkable combinatorial and geometric properties. However, it doesn’t have finite local complexi...... combinatorial data, which rather automatically has finite local complexity. In this paper we give a construction of the discrete hull just from the combinatorial data. The main result of this paper is that the discrete hull is a Cantor space....

  14. Drag resistance measurements for newly applied antifouling coatings and welding seams on ship hull surface

    DEFF Research Database (Denmark)

    Wang, Xueting; Olsen, S. M.; Andres, E.

    Drag resistances of newly applied antifouling coatings and welding seams on ship hull surface have been investigated using a pilot-scale rotary setup. Both conventional biocide-based antifouling (AF) coatings and silicone-based fouling release (FR) coatings have been studied and compared in their......Drag resistances of newly applied antifouling coatings and welding seams on ship hull surface have been investigated using a pilot-scale rotary setup. Both conventional biocide-based antifouling (AF) coatings and silicone-based fouling release (FR) coatings have been studied and compared...

  15. Maintained ship hull girder ultimate strength reliability considering corrosion and fatigue

    DEFF Research Database (Denmark)

    Hu, Yong; Cui, W.; Pedersen, Preben Terndrup

    2004-01-01

    The prupose of this paper is to propose a methodology to assess the time-variant ultimate strength of ship hull girder under the degradations of corrosion and fatigue. The effects of fatigue cracks on the tensile and compressive residual ultimate strength of stiffened panels and unstiffened plates......, webs and flanges, respectively. The effects of inspections and repair are taken into account. A minimum net thickness rule is used to determine repair policies. A procedure is proposed to determine the maximum allowable corrosion thickness of different parts of the hull cross section. The procedure...

  16. Acoustic emission localization on ship hull structures using a deep learning approach

    DEFF Research Database (Denmark)

    Georgoulas, George; Kappatos, Vassilios; Nikolakopoulos, George

    2016-01-01

    In this paper, deep belief networks were used for localization of acoustic emission events on ship hull structures. In order to avoid complex and time consuming implementations, the proposed approach uses a simple feature extraction module, which significantly reduces the extremely high dimension......In this paper, deep belief networks were used for localization of acoustic emission events on ship hull structures. In order to avoid complex and time consuming implementations, the proposed approach uses a simple feature extraction module, which significantly reduces the extremely high...

  17. Hydrodynamic design of an underwater hull cleaning robot and its evaluation

    Directory of Open Access Journals (Sweden)

    Man Hyung Lee

    2012-12-01

    Full Text Available An underwater hull cleaning robot can be a desirable choice for the cleaning of large ships. It can make the cleaning process safe and economical. This paper presents a hydrodynamic design of an underwater cleaning robot and its evaluation for an underwater ship hull cleaning robot. The hydrodynamic design process of the robot body is described in detail. Optimal body design process with compromises among conflicting design requirements is given. Experimental results on the hydrodynamic performance of the robot are given.

  18. In vitro antibacterial and free radical scavenging activity of green hull of Juglans regia

    Directory of Open Access Journals (Sweden)

    Pardeep Sharma

    2013-08-01

    Full Text Available Antioxidant supplements from plants are vital to count the oxidative damage in cells. We assessed the antioxidants and antibacterial activity of green hull of Juglans regia in this study. According to our results the maximum antibacterial activity was observed in ethanolic extract when compared to other extract. So, the ethanolic extract was studied for antioxidant activity which exhibited high antiradical activity against DPPH, hydroxyl, and nitric oxide radicals. In conclusion, green hull of J. regia showed strong reducing power activity and total antioxidant capacity. The results justify the therapeutic application of plant in the indigenous system of medicine. Keywords: Juglans regia, Ethanolic extract, Antioxidants, DPPH, Antibacterial activity

  19. Unplanned Pregnancy and Contraceptive Use in Hull and East Yorkshire

    Science.gov (United States)

    Bexhell, Helen; Guthrie, Kate; Cleland, Kelly; Trussell, James

    2015-01-01

    Objective This study has two aims. The first is to assess the proportion of unplanned pregnancies among women attending antenatal clinics and those undergoing induced abortion (IA). The second is to assess both their previous contraceptive use and contraceptive intention, with particular focus on the use or consideration of any long acting reversible contraceptives in Hull and East Riding in order to inform service redesign. Study Design Consecutive women attending their first antenatal clinic (ANC) appointment and women attending a gynaecology clinic undergoing induced abortion (IA) were asked to complete a 2-page questionnaire that contained a validated pregnancy intendedness questionnaire (the London Measure of Unplanned Pregnancy (LMUP)) and questions to establish contraceptive use and access prior to this index pregnancy. Results The overall response rate was 69%. We received 648 evaluable questionnaires for women undergoing IA. Of these pregnancies, 75.8% (95% CI 72.3%-79.0%) were unplanned (LMUP score 0-3). We received 1001 evaluable questionnaires from women booking at antenatal clinics. Of these pregnancies, 5.5% (95% CI 4.2%-7.0%) were unplanned. Among those with unplanned pregnancies who were not using contraception 31% reported that they were unable to obtain the method they wanted. Among those using a method immediately prior to the index unplanned pregnancy, 33% stated it was not the method they wanted; of these 75% would have preferred sterilization, the implant, injectable, or intrauterine contraceptive. Conclusion Unplanned pregnancies in this population are common among women undergoing IA but are uncommon among women attending an ANC. About a third of women not using contraception reported that they were unable to obtain the method they wanted, and about a third of women using contraception stated that they were not using the method they would have preferred. Implications Opportunities to prevent unplanned pregnancies are missed when staff in

  20. Zinc electrowinning analysis in a modified Hull cell

    Science.gov (United States)

    McColm, Thomas Dean

    The Hull cell is an analytical cell designed with trapezoidal geometry to incorporate a range of current densities into a single experiment. It was conceived to examine electroplating processes rather than mass production processes. A modified analytical cell was designed, developed and applied to the diagnosis of zinc electrowinning. Emphasis was placed on obtaining the quantitative variation of current efficiency with current density and the associated microscopic variation in deposit morphology. Current density distributions came by placing an insulating baffle in between parallel electrodes. The baffle position and length were easily adjusted, allowing the generation of 12 different distributions for a single applied potential. Ten electrically isolated 1 cm2 segments comprised the cathode. Measurement of the potential drop across I ohm resistors in each of the ten isolated parallel branches permitted direct quantitative determination of current densities. The small segments permitted simple SEM and X-ray analysis of deposits. The cell was designed to allow the continual cycling of electrolyte. In conjunction with experimental analysis, a technique for the determination of current efficiency was tested and developed. The technique involved the comparison of charge passed for the electrodeposition and subsequent electrodissolution of a given mass of zinc and removed the necessity to determine the mass directly. In no prior studies on zinc electrowinning had current efficiencies been determined this way. The cell and technique were developed and verified by the correct diagnosis of industrial zinc electrowinning. Successful determination of the effects of key variables including temperature, acid to zinc ratio and impurity effects on current efficiency and deposit morphology was demonstrated. In parallel with experimental work, cell electrochemistry was modeled. Primary and secondary input parameters were those pertinent to zinc electrowinning. The resultant

  1. On the Effect of Hull Girder Flexibility on the Vertical Wave Bending Moment for Ultra Large Container Vessels

    DEFF Research Database (Denmark)

    Andersen, Ingrid Marie Vincent; Jensen, Jørgen Juncher

    2012-01-01

    Currently, a number of very large container ships are being built and more are on order, and some concerns have been expressed about the importance of the reduced hull girder stiffness to the wave-induced loads. The main concern is related to the fatigue life, but also a possible increase...... in the global hull girder loads as consequence of the increased hull flexibility must be considered. This is especially so as the rules of the classification societies do not explicitly account for the effect of hull flexibility on the global loads. In the present paper an analysis has been carried out...... in the waves. Slamming forces are determined by a standard momentum formulation. The hull flexibility is modelled as a nonprismatic Timoshenko beam. Generally, good agreement with experimental results and more accurate numerical predictions has previously been obtained in a number of studies. The statistical...

  2. Estimation of hull girder vertical bending moments including non-linear and flexibility effects using closed form expressions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Jensen, Jørgen Juncher

    2009-01-01

    A simple but rational procedure for prediction of extreme wave-induced hull girder bending moment is presented. The procedure takes into account main ship hull characteristics such as: length, breadth, draught, block coefficient, bow flare coefficient, forward speed and hull flexibility. The wave......-linear strip theory calculations and supplemented with new closed form results for the hogging bending moment. Focus is on the extreme hull girder hogging bending moment. Due to the few input parameters this procedure can be used to estimate the wave-induced bending moments at the conceptual design phase....... Another application area is for novel single hull ship types not presently covered by the rules of the classification societies. As one application example the container ship M/S Napoli is considered....

  3. Groundwater flow cycling between a submarine spring and an inland fresh water spring.

    Science.gov (United States)

    Davis, J Hal; Verdi, Richard

    2014-01-01

    Spring Creek Springs and Wakulla Springs are large first magnitude springs that derive water from the Upper Floridan Aquifer. The submarine Spring Creek Springs are located in a marine estuary and Wakulla Springs are located 18 km inland. Wakulla Springs has had a consistent increase in flow from the 1930s to the present. This increase is probably due to the rising sea level, which puts additional pressure head on the submarine Spring Creek Springs, reducing its fresh water flow and increasing flows in Wakulla Springs. To improve understanding of the complex relations between these springs, flow and salinity data were collected from June 25, 2007 to June 30, 2010. The flow in Spring Creek Springs was most sensitive to rainfall and salt water intrusion, and the flow in Wakulla Springs was most sensitive to rainfall and the flow in Spring Creek Springs. Flows from the springs were found to be connected, and composed of three repeating phases in a karst spring flow cycle: Phase 1 occurred during low rainfall periods and was characterized by salt water backflow into the Spring Creek Springs caves. The higher density salt water blocked fresh water flow and resulted in a higher equivalent fresh water head in Spring Creek Springs than in Wakulla Springs. The blocked fresh water was diverted to Wakulla Springs, approximately doubling its flow. Phase 2 occurred when heavy rainfall resulted in temporarily high creek flows to nearby sinkholes that purged the salt water from the Spring Creek Springs caves. Phase 3 occurred after streams returned to base flow. The Spring Creek Springs caves retained a lower equivalent fresh water head than Wakulla Springs, causing them to flow large amounts of fresh water while Wakulla Springs flow was reduced by about half. Published 2013. This article is a U.S. Government work and is in the public domain in the USA.

  4. Laurel Springs & DoDEA

    National Research Council Canada - National Science Library

    Jhung, Seung

    2000-01-01

    At the request of the client organization, Laurel Springs School, we developed an in-depth market analysis of comparable educational programs offered within the Department of Defense Education Activities (DoDEA...

  5. Spring Small Grains Area Estimation

    Science.gov (United States)

    Palmer, W. F.; Mohler, R. J.

    1986-01-01

    SSG3 automatically estimates acreage of spring small grains from Landsat data. Report describes development and testing of a computerized technique for using Landsat multispectral scanner (MSS) data to estimate acreage of spring small grains (wheat, barley, and oats). Application of technique to analysis of four years of data from United States and Canada yielded estimates of accuracy comparable to those obtained through procedures that rely on trained analysis.

  6. Marble Canyon spring sampling investigation

    International Nuclear Information System (INIS)

    McCulley, B.

    1985-10-01

    The Mississippian Leadville Limestone is the most permeable formation in the lower hydrostratigraphic unit underlying the salt beds of the Paradox Formation in Gibson Dome, Paradox Basin, Utah, which is being considered as a potential nuclear waste repository site. The closest downgradient outcrop of the Mississippian limestone is along the Colorado River in Marble Canyon, Arizona. This report describes the sampling and interpretation of springs in that area to assess the relative contribution of Gibson Dome-type Leadville Limestone ground water to that spring discharge. The high-volume (hundreds of liters per second or thousands of gallons per minute) springs discharging from fault zones in Marble Canyon are mixtures of water recharged west of the Colorado River on the Kaibab Plateau and east of the river in the Kaiparowits basin. No component of Gibson Dome-type Leadville Limestone ground water is evident in major and trace element chemistry or isotopic composition of the Marble Canyon Springs. A low-volume (0.3 liters per second or 5 gallons per minute) spring with some chemical and isotopic characteristics of Gibson Dome-type Leadville Limestone water diluted by Kaiparowits basin-type water issues from a travertine mound in the Bright Angel Shale on the Little Colorado River. However, the stable isotopic composition and bromide levels of that spring discharge, in addition to probable ground-water flow paths, contradict the dilution hypothesis

  7. Gasified rice hull biochar affects nutrition and growth of five horticulture crops in container culture

    Science.gov (United States)

    Phosphate fertilizers used in the production of greenhouse crops can be problematic if released into the environment. Furthermore, the price of phosphate is increasing as demand increases and world supplies decrease. The objective of this research was to determine if gasified rice hull biochar (GR...

  8. Anti-diabetic effects of rice hull smoke extract in alloxan-induced diabetic mice

    Science.gov (United States)

    We investigated the protective effect of a liquid rice hull smoke extract (RHSE) against diabetes in alloxan-induced diabetic mice. Anti-diabetic effects of RHSE were evaluated in both the rat insulinoma-1 cell line (INS-1) and diabetic ICR mice induced by inraperitoneal (ip) injection of alloxan. ...

  9. Characterization of hydrolytic degradation of polylactic acid/rice hulls composites in water at different temperatures

    Directory of Open Access Journals (Sweden)

    2011-02-01

    Full Text Available Hydrolytic degradations of polylactic acid/rice hulls (PLA/RH composites with various rice hulls contents due to water absorptions at 23, 51 and 69°C were investigated by studying the thermal properties, chemical composition, molecular weight, and morphology of the degraded products. The results have attested that the stability of PLA/RH composites in water depends slightly on rice hulls contents but it is significantly influenced by water temperature. Water absorption in 30 days at 23°C was between 0.87 and 9.25% depending on rice hull contents. However, at thermophilic temperatures, the water absorption and degradation of these products were increased significantly. Saturations were achieved in less than 25 and 9 days at 51°C and 69°C, respectively, while hydrolytic degradation was demonstrated by an increase in fragility and development of crystallinity. At 69°C, there were significant reductions of the decomposition and glass transition temperatures of the polymer by 13°C. These changes were associated with the reduction of the molecular weight of PLA from 153.1 kDa to ~10.7 kDa due to hydrolysis of its ester group.

  10. The Effect of Buckwheat Hull Extract on Lipid Oxidation in Frozen-Stored Meat Products.

    Science.gov (United States)

    Hęś, Marzanna; Szwengiel, Artur; Dziedzic, Krzysztof; Le Thanh-Blicharz, Joanna; Kmiecik, Dominik; Górecka, Danuta

    2017-04-01

    This study investigated the effect of antioxidants on lipid stability of frozen-stored meat products. Buckwheat hull extract was used to enrich fried meatballs made from ground pork. During 180-d storage of meat products, lipid oxidation (peroxide and 2-thiobarbituric acid reactive substances [TBARS] value) was periodically monitored. The results were compared with butylated hydroxytoluene (BHT). The addition of antioxidants decreased lipid oxidation in stored meatballs. The highest ability to control peroxide and TBARS values was demonstrated for buckwheat hull extract. Moreover, buckwheat hull extract showed a higher 2,2-diphenyl-1-picrylhydrazyl free radical scavenging activity as well as higher Fe(II) ion chelating ability, as compared with BHT. The total content of phenolic compounds are highly correlated to the individual polyphenols in extract of buckwheat hull, among which the following were assayed: 3,4-dihydroxybenzoic acid, 4-hydroxybenzoic acid, gallic acid, isovanillic acid and p-coumaric acid, and flavonoids: isoorientin, quercetin, quercetin 3-d-glucoside, rutin, and vitexin. These results indicate that plant extracts can be used to prolong shelf life of products by protecting them against lipid oxidation and deterioration of their nutritional quality. © 2017 Institute of Food Technologists®.

  11. MAO-A inhibitory activity of quercetin from Calluna vulgaris (L.) Hull

    DEFF Research Database (Denmark)

    Saaby, Lasse; Rasmussen, Hasse Bonde; Jäger, Anna Katharina

    2009-01-01

    AIM OF THE STUDY: This study investigated MAO-A inhibitory activity of methanol extract of Calluna vulgaris (L.) Hull., which traditionally has been used as a nerve calming remedy. MATERIALS AND METHODS: A methanolic extract of Calluna vulgaris was partitioned against heptane, ethyl acetate...

  12. Convex hull and tour crossings in the Euclidean traveling salesperson problem : implications for human performance studies

    NARCIS (Netherlands)

    Rooij, van I.; Stege, U.; Schactman, A.

    2003-01-01

    Recently there has been growing interest among psychologists in human performance on the Euclidean traveling salesperson problem (E-TSP). A debate has been initiated on what strategy people use in solving visually presented E-TSP instances. The most prominent hypothesis is the convex-hull

  13. Parametric roll due to hull instantaneous volumetric changes and speed variations

    DEFF Research Database (Denmark)

    Vidic-Perunovic, Jelena; Jensen, Jørgen Juncher

    2009-01-01

    Parametric roll of a containership in head sea condition has been studied in the paper. A time domain routine for GZ righting arm calculation based on exact underwater hull geometry has been implemented into a two-degree-of-freedom procedure for roll response calculation. The speed variation due...

  14. On the convex hull of the simple integer recourse objective function

    NARCIS (Netherlands)

    Klein Haneveld, Willem K.; Stougie, L.; van der Vlerk, Maarten H.

    1995-01-01

    We consider the objective function of a simple integer recourse problem with fixed technology matrix. Using properties of the expected value function, we prove a relation between the convex hull of this function and the expected value function of a continuous simple recourse program. We present an

  15. Rice hull mulch affects germination of bittercress and creeping woodsorrel in container plant culture

    Science.gov (United States)

    Mulches are commonly used to control weeds in container nursery crops, especially in sites where preemergence herbicides are either not labeled or potentially phytotoxic to the crop. Parboiled rice hulls have been shown to provide effective weed control when applied 1.25 to 2.5 cm deep over the con...

  16. Report of the Committee on the Survey of Hull Bottom of Nuclear Ship Mutsu

    International Nuclear Information System (INIS)

    1979-01-01

    The nuclear ship Mutsu arrived the Sasebo Shipyard, Sasebo Heavy Industries Co., Ltd., in October, 1978, to repair the shielding for the reactor and to inspect generally the safety. The docking works were not carried out since 1972 for the Mutsu, therefore it was decided to admit the Mutsu in a dock to put the hull in order. To prepare for starting the output test again, it is necessary to grasp the state of the hull part below water line and take appropriate measures as occasions demand, therefore the Japan Nuclear Ship Development Agency established the Committee on the Survey of Hull Bottom of Nuclear Ship Mutsu in July, 1979. Three meetings of the committee were held from July 2 to September 19, and the draft of the report was drawn up. The Mutsu entered No. 5 dock of the Sasebo Shipyard on July 9, and left on July 23, and the survey of the hull bottom was carried out during that period. The results of the survey are reported as follows: the state of bottom shell plates, the state of aft part and the propeller, the state of sea chests, the state of the electrical corrosion protection of bottom shell plates and the state of sea valves. The problem to be specially mentioned was not found, and it was recognized that the sound maintenance has been carried out. (Kako, I.)

  17. Conditioning and storage of spent fuel cladding hulls by rolling and embedding in concrete

    International Nuclear Information System (INIS)

    Spenk, G.; Frotscher, H.; Graebner, H.; Kapulla, H.

    1981-01-01

    Under a contract with the European Atomic Energy Community the Kernforschungszentrum Karlsruhe, KfK, developed a conditioning process for LWR cladding waste. After compaction of the hulls by rolling they are embedded in a concrete matrix. In addition to basic data of the cladding waste, the compaction process, consisting of a dosage system and a rolling mill, is described. Several embedding techniques are possible, but a final selection has still to be made. Best results will probably be achieved by a vacuum technique. To characterize the waste product, leach tests have been started. The compression strength of compacted hulls embedded in concrete was determined to 2300 N.cm -2 . Hydrogen release due to radiolyses lies around 3 μl.g -1 sub(concrete).Mrad -1 which corresponds to the values expected on account of the water content of the samples. Less hydrogen was determined in samples with Zircaloy added. The tritium release of tritiated Zircaloy hulls embedded in concrete is greatly dependent on temperature and irradiation. At 100 0 C and with γ-irradiation the tritium release is about two orders of magnitude higher compared with experiments without irradiation. The thermal conductivity of samples of Zircaloy hulls embedded in concrete was determined to be 1.4W.m -1 .K -1 . (author)

  18. On Linear Hulls, Statistical Saturation Attacks, PRESENT and a Cryptanalysis of PUFFIN

    DEFF Research Database (Denmark)

    Leander, Gregor

    2011-01-01

    which breaks the cipher for at least a quarter of the keys with a complexity less than 258. In the case of PRESENT we show that the design is sound. The design criteria are sufficient to ensure the resistance against linear attacks, taking into account the notion of linear hulls. Finally, we show...

  19. Phenol metabolism and preservation of fresh in-hull walnut stored in modified atmosphere packaging.

    Science.gov (United States)

    Wang, Jin; Li, Pan; Gong, Bi; Li, Shuying; Ma, Huiling

    2017-12-01

    The effects of modified atmosphere packaging (MAP) on phenol metabolism and preservation of fresh in-hull walnuts have been investigated. Fruit was packaged under MAP1 (film thickness, 30 μm), MAP2 (45 μm) and MAP3 (50 μm) and stored at -0.5 to 1.0 °C for up to 60 days. Firmness, soluble solid concentration, total phenols, total flavonoids and total antioxidant activity of the green hull were maintained at higher levels under the MAP conditions, whereas decay incidence was lower compared to the control during storage. Green hull of fruit under MAP conditions contained lower polyphenol oxidase activity than the control and the peroxidase activity was at a similar level to the control after 18 days. Phenylalanine ammonialyase activity was enhanced by MAP conditions, with two peaks on days 18 and 36. Until day 60, the peroxide value and acid value of kernel oils under MAP conditions were lower than that of the control. The MAP3 treatment was most effective for maintaining kernel quality. The protective role of MAP conditions on phenolic contents in green hull may contribute to the mitigation of decay and the maintenance of kernel quality. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  20. Multiobjective optimization of classifiers by means of 3D convex-hull-based evolutionary algorithms

    NARCIS (Netherlands)

    Zhao, J.; Basto, Fernandes V.; Jiao, L.; Yevseyeva, I.; Asep, Maulana A.; Li, R.; Bäck, T.H.W.; Tang, T.; Michael, Emmerich T. M.

    2016-01-01

    The receiver operating characteristic (ROC) and detection error tradeoff(DET) curves are frequently used in the machine learning community to analyze the performance of binary classifiers. Recently, the convex-hull-based multiobjective genetic programming algorithm was proposed and successfully

  1. Parboiled rice hull mulch in containers reduces liverwort and bittercress growth

    Science.gov (United States)

    Use of preemergence herbicides for weed control is not always possible; some crops and many enclosed production sites are not labeled for herbicide applications. The objective of this research was to determine the utility of parboiled rice hull mulch for controlling two of the most common weeds in ...

  2. Structural equation models based on multivariate diversity assessment of diploid and tetraploid hulled wheat species

    Science.gov (United States)

    Hulled wheats are largely untapped genetic resources with >10,000 years of genetic memory and diversity that can be used for wheat quality improvement, development of healthy products, and adaptation to climate change. Multivariate diversity was assessed in the diploid Triticum monococcum L. var mon...

  3. Optimisation of dilute acid pre-treatment of artisan rice hulls for ethanol production

    International Nuclear Information System (INIS)

    Lopez, Yoney; Martin, Carlos; Gullon, Beatriz; Parajo, Juan Carlos

    2011-01-01

    Rice hulls are potential low-cost feedstocks for fuel ethanol production in many countries. In this work, the dilute-acid pre-treatment of artisan rice hulls was investigated using a central composite rotatable experimental design. The experimental variables were temperature (140-210 C), biomass load (5-20%) and sulphuric acid concentration (0.5-1.5 g per 100 g of reaction mixture). A total of 16 experimental runs, including a 23-plan, two replicates at the central point and six star points, were carried out. Low temperatures were found to be favourable for the hydrolysis of xylan and of the easily hydrolyzable glucan fraction. High glucose formation (up to 15.3 g/100 g), attributable to starch hydrolysis, was detected in the hydrolysates obtained under the least severe pre-treatment conditions. Using the experimental results, several models for predicting the effect of the operational conditions on the yield of pretreated solids, xylan and glucan conversion upon pre-treatment, and on enzymatic convertibility of cellulose were developed. Optimum results were predicted for the conversion of easily-hydrolyzable glucan in the material pretreated at 140.7 C, and for the enzymatic saccharification of cellulose in the material pretreated at 169 C. These results suggested the use of two-step acid hydrolysis as future pre-treatment strategy for artisan rice hulls. Key words: Dilute acid hydrolysis, enzymatic hydrolysis, pre-treatment, rice hulls. (author)

  4. with rice hulls on pH and ammonia emissions from poultry houses

    African Journals Online (AJOL)

    The use of aluminum sulfate [alum; Al2(SO3)4·14H2O] as top dressing to poultry litter has been proven in reducing ammonia (NH3) volatilization under both laboratory and field tests; however, there has been no information of alum application in mixing methods from poultry litter or rice hulls. The aim of the experiment was ...

  5. The Effect of Hull Biofouling on Parameters Characterising Ship Propulsion System Efficiency

    Directory of Open Access Journals (Sweden)

    Tarełko Wiesła

    2015-01-01

    Full Text Available One of most important issues concerning technical objects is the increase of their operating performance. For a ship this performance mainly depends on the efficiency of its main pro-pulsion system and the resistance generated during its motion on water. The overall ship re-sistance, in turn, mainly depends on the hull friction resistance, closely related with the pres-ence of different types of roughness on the hull surface, including underwater part biofouling. The article analyses the effect of hull biofouling on selected parameters characterising the efficiency of the ship propulsion system with adjustable propeller. For this purpose a two-year research experiment was performed on a sailing vessel during its motor navigation phases. Based on the obtained results, three groups of characteristics were worked out for different combinations of engine rotational speed and adjustable propeller pitch settings. The obtained results have revealed that the phenomenon of underwater hull biofouling affects remarkably the parameters characterising propulsion system efficiency. In particular, the development of the biofouling layer leads to significant reduction of the speed of navigation.

  6. The flavonoid herbacetin diglucoside as a constituent of the lignan macromolecule from flaxseed hulls

    NARCIS (Netherlands)

    Struijs, K.; Vincken, J.P.; Verhoef, R.P.; Oostveen, van W.H.M.; Voragen, A.G.J.; Gruppen, H.

    2007-01-01

    Lignans in flaxseed are known to be part of a macromolecule in which they are connected through the linker-molecule hydroxy-methyl-glutaric acid (HMGA). In this study, the lignan macromolecule was extracted from flaxseed hulls and degraded to its monomeric constituents by complete saponification.

  7. Ship hull fouling in the port of Recife, Pernambuco

    Directory of Open Access Journals (Sweden)

    Cristiane Maria Rocha Farrapeira

    2007-09-01

    Full Text Available Ports of big coastal cities are exposed to exotic species as a consequence of shipping traffic. As the Port of Recife receives an annual average of 491 ships from other regions of Brazil and from all over the world, this work was aimed at knowing which marine animals were passively transported on such vessels hulls, in order to map and monitor new bioinvasions in the area. Thus, 32 vessels of several origins were investigated between November 2005 and March 2006, samples were taken and the macrofauna identified. Sixty species of associated animals were identified, consisting of 28 sessile species, particularly the Cirripedia Balanomorpha and Lepadomorpha as dominants, 8 sedentary animals, namely Mytillidae and Dreissenidae and 23 free-living species, particularly, Caprellidae, Gammaridae, Tanaidacea, Turbellaria, Nemertea and Polychaeta. The first occurrence of Conchoderma virgatum was recorded with exact location for the Brazilian littoral, and Conchoderma auritum, Amphibalanus subalbidus and Haliplanella lineata were recorded for the first time at the littoral of Pernambuco State. The invasion pathway was confirmed for Amphibalanus reticulatus and Mytilopsis leucophaeta, invader species of the estuarine area of Recife's city. Megabalanus coccopoma was considered as a risk invader species for the region.Regiões portuárias das grandes cidades litorâneas estão sujeitas à recepção de espécies exóticas como conseqüência da movimentação dos navios. Como o Porto do Recife recebe uma média anual de 491 atracações de navios, provenientes de várias regiões do Brasil e do mundo, objetivou-se conhecer quais animais marinhos eram transportados passivamente nos cascos das embarcações para mapear e monitorar novas invasões biológicas na área. Assim, foram investigados 32 barcos de diversas origens, nos meses de novembro de 2005 a março de 2006, tendo a macrofauna sido amostrada e identificada. Foram encontradas 60 espécies de animais

  8. Fossilization Processes in Thermal Springs

    Science.gov (United States)

    Farmer, Jack D.; Cady, Sherry; Desmarais, David J.; Chang, Sherwood (Technical Monitor)

    1995-01-01

    To create a comparative framework for the study of ancient examples, we have been carrying out parallel studies of the microbial biosedimentology, taphonomy and geochemistry of modem and sub-Recent thermal spring deposits. One goal of the research is the development of integrated litho- and taphofacies models for siliceous and travertline sinters. Thermal springs are regarded as important environments for the origin and early evolution of life on Earth, and we seek to utilize information from the fossil record to reconstruct the evolution of high temperature ecosystems. Microbial contributions to the fabric of thermal spring sinters occur when population growth rates keep pace with, or exceed rates of inorganic precipitation, allowing for the development of continuous biofilms or mats. In siliceous thermal springs, microorganisms are typically entombed while viable. Modes of preservation reflect the balance between rates of organic matter degradation, silica precipitation and secondary infilling. Subaerial sinters are initially quite porous and permeable and at temperatures higher than about 20 C, organic materials are usually degraded prior to secondary infilling of sinter frameworks. Thus, organically-preserved microfossils are rare and fossil information consists of characteristic biofabrics formed by the encrustation and underplating of microbial mat surfaces. This probably accounts for the typically low total organic carbon values observed in thermal spring deposits. In mid-temperature, (approx. 35 - 59 C) ponds and outflows, the surface morphology of tufted Phormidium mats is preserved through mat underplating by thin siliceous: crusts. Microbial taxes lead to clumping of ceils and/or preferred filament orientations that together define higher order composite fabrics in thermal spring stromatolites (e.g. network, coniform, and palisade). At lower temperatures (less than 35 C), Calothrix mats cover shallow terracette pools forming flat carpets or pustular

  9. Utilization of Passion fruit hulls (Passiflora edulis Sims f. edulis Deg as component of complete feed for growing Kacang goats

    Directory of Open Access Journals (Sweden)

    Kiston Simanihuruk

    2009-03-01

    Full Text Available Processing of passion fruit (Passiflora edulis Sims f. edulis Deg to produce passion fruit juice produce passion fruit hulls that is potential for feedstuff. Twenty male kacang goats (average initial body weight 17±1.24 kg were used in an experiment to study the effect of utilization of passion fruit hulls as feed component in the complete pellet ration on their growth. The experiment was arranged in completely randomized design consisting of 4 diets and 5 replications. Animal were randomly allocated into 4 diets (0, 15, 30, 45% level of passion fruit hulls. Each diet contained 14% crude protein and 2550 Kcal kg-1 metabolism energy. The ration was offered at 3.8% of body weight based on dry matter. The result of the experiment showed that all variables observed were not affected by level of passion fruit hulls (P>0.05. Average daily gain and feed efficiency tended to decrease with the increase level of passion fruit hulls. The highest dry matter, organic matter and N intake (768,78 g h-1 d-1; 687,37 g h-1 d-1 and 17,22 g h-1 d-1 respectively were found from R1 treatment (15% level of passion fruit hulls. It was concluded that passion fruit hulls can be used till 45% level in the diet of Kacang goat.

  10. Kinetics and the mass transfer mechanism of hydrogen sulfide removal by biochar derived from rice hull.

    Science.gov (United States)

    Shang, Guofeng; Liu, Liang; Chen, Ping; Shen, Guoqing; Li, Qiwu

    2016-05-01

    The biochar derived from rice hull was evaluated for its abilities to remove hydrogen sulfide (H2S) from gas phase. The surface area and pH of the biochar were compared. The biochar derived from rice hull was evaluated for its abilities to remove hydrogen sulfide (H2S) from gas phase. The surface area and pH of the biochar were compared. The different pyrolysis temperature has great influence on the adsorption of H2S. At the different pyrolysis temperature, the H2S removal efficiency of rice hull-derived biochar was different. The adsorption capacities of biochar were 2.09 mg·g(-1), 2.65 mg·g(-1), 16.30 mg·g(-1), 20.80 mg·g(-1), and 382.70 mg·g(-1), which their pyrolysis temperatures were 100 °C, 200 °C, 300 °C, 400 °C and 500 °C respectively. Based on the Yoon-Nelson model, it analyzed the mass transfer mechanism of hydrogen sulfide adsorption by biochar. The paper focuses on the biochar derived from rice hull-removed hydrogen sulfide (H2S) from gas phase. The surface area and pH of the biochar were compared. The different pyrolysis temperatures have great influence on the adsorption of H2S. At the different pyrolysis temperatures, the H2S removal efficiency of rice hull-derived biohar was different. The adsorption capacities of biochar were 2.09, 2.65, 16.30, 20.80, and 382.70 mg·g(-1), and their pyrolysis temperatures were 100, 200, 300, 400, and 500 °C, respectively. Based on the Yoon-Nelson model, the mass transfer mechanism of hydrogen sulfide adsorption by biochar was analyzed.

  11. Impact of total substitution of corn for soybean hulls in diets for lambs

    Directory of Open Access Journals (Sweden)

    Milena Patricia Viana Bastos

    2015-03-01

    Full Text Available The experiment was conducted to assess the effect of substituting corn for soybean hulls on the apparent digestibility of nutrients, carcass performance and characteristics, and yield of cuts of 25 non-castrated male Santa Ines lambs with an initial body weight of 20±2 kg, at approximately 6 months of age, sheltered individually in stalls (1.10 × 1.0 m, considering a totally randomized design, fed 600 g/kg of forage and 400 g/kg of concentrate. Soybean hulls replaced corn at 0, 250, 500, 750, and 1,000 g/kg of dry matter. The intake of dry matter (DM, organic matter (OM, neutral detergent fiber (NDF, acid detergent fiber (ADF, NDF corrected for ash and protein (NDFap, total carbohydrates (TC, non-fibrous carbohydrates (NFC and total digestible nutrients (TDN in g/day, and the digestibility of NFC increased linearly with the soybean hull replacement. Crude protein intake displayed a quadratic response, whereas the intake of EE in g/day, the apparent digestibility coefficients of DM, OM, CP, EE, NDF, ADF, NDFap and TC, TDN, average daily gain, carcass characteristics, and yield of cuts were not affected by the soybean hull levels. Soybean hull substitution increased the intake of DM and nutrients, making it possible to replace up to 1,000 g/kg of dry matter in the diets for confined sheep, as it does not compromise performance, digestibility, carcass characteristics, or yield of cuts when used in sheep nutrition.

  12. The effects of vibratory stimulation employed to forearm and arm flexor muscles on upper limb function in patients with chronic stroke.

    Science.gov (United States)

    Jung, Sang-Mi

    2017-09-01

    [Purpose] The purpose of this study was to investigate not only the effects of stimulatory vibration but also the retained effects 2 weeks after the last session of the intervention. [Subjects and Methods] Ten subjects with post-stroke hemiplegia were recruited in this study. The experimental group (EG) received vibratory stimulation for 30 minutes in each session, three times a week for 2 weeks. Grip strength (GS), box-and-block test (BBT), and Weinstein monofilament were used to assess hand strength, dexterity, and sensory in the affected hand, respectively. [Results] A significant difference was found between the pre- and post-follow-up BBT. Significant differences were found among the pre-posttest, post-follow-up test, and pre-follow-up test results for GS and BBT. [Conclusion] This study was conducted with 10 subjects, without a control group, to verify the pure effect of the intervention. As a result, significant positive effects were observed in the post-test and follow-up test of GS and BBT. Therefore, repeated vibratory stimulation influenced GS and BBT after the 2-week intervention and retained the effect for 2 more weeks.

  13. Obtention of hydroxyapatite submicrometric of bovine origin by vibratory grinding for rapid prototyping; Obtencao de hidroxiapatita submicrometrica de origem bovina por moagem vibratoria visando prototipagem rapida

    Energy Technology Data Exchange (ETDEWEB)

    Meira, C.R.; Purquerio, B.M.; Fortulan, C.A., E-mail: camilameira@sc.usp.br [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Escola de Engenharia; Braga, F.J.C. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    Submicron bovine hydroxyapatite was obtained for rapid prototyping. Hydroxyapatite structure originated from bovine mineral bone has great importance among the biomaterials and biocompatibility due to its great similarity with the human bone structure. This study aims to obtain powder for manufacture by rapid prototyping of scaffolds. This technique manufacture requires highly reactive powders to compensate for the absence of pressure forming. Hydroxyapatite was milled in a ball mill and vibratory mill, and analyzed for their average equivalent spherical diameter and surface area. Test specimens were isostatically pressed at 100 MPa and machined into cylindrical test specimens. These specimens were sintered at several temperatures to determine the optimal sintering temperature based on densification and chemistry stability. In grinding ball mill was obtained particles of equivalent diameter of 0.74 micron in vibratory mill of 0.46 micrometers. An average flexural strength of 100 MPa and 99,8% of real density was attained for the sample sintered at 1300 deg C/2h, signaling potential for use in rapid prototyping. (author)

  14. Spring harvest of corn stover

    Energy Technology Data Exchange (ETDEWEB)

    Lizotte, P.L. [Laval Univ., Quebec City, PQ (Canada). Dept. des sols et de genie agroalimentaire; Savoie, P. [Agriculture and Agri-Food Canada, Quebec City, PQ (Canada)

    2010-07-01

    Corn stover is typically left behind in the field after grain harvest. Although part of the stover should remain in the field for soil organic matter renewal and erosion protection, half of the stover could be removed sustainably. This represents about one million t dry matter (DM) of stover per year in the province of Quebec. Stover harvested in the fall is very wet. While there are applications for wet stover, the available markets currently require a dry product. Preliminary measurements have shown that stover left in the field throughout the winter becomes very dry, and a considerable amount would still be harvestable in the spring. In the spring of 2009, corn stover was harvested at 2 sites, each subdivided into 2 parcels. The first parcel was cut and raked in the fall of 2008 (fall parcel), while the second parcel was cut and raked in spring 2009. Fibre from both parcels was baled in the spring 2009. At the first site, a large square baler was used in late April to produce bales measuring 0.8 m x 0.9 m x 1.8 m. On the second site a round baler was used in late May to produce bales of 1.2 m in width by 1.45 m in diameter. On the second site, a small square baler was also used to produce bales of 0.35 m x 0.45 m x 0.60 m (spring cutting only). With the large square baler, an average of 3.9 t DM/ha was harvested equally on the fall parcel and the spring parcel, representing a 48 per cent recovery of biomass based on stover yields.

  15. Instant Spring for Android starter

    CERN Document Server

    Dahanne, Anthony

    2013-01-01

    Packt Instant Starter: get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks.This is a Starter which gives you an introduction to Spring for Android with plenty of well-explained practical code examples.If you are an Android developer who wants to learn about RESTful web services and OAuth authentication and authorization, and you also want to know how to speed up your development involving those architectures using Spring for Android abstractions, then this book is for you.But core Java developers

  16. Spring for It: First Novels

    Science.gov (United States)

    Hoffert, Barbara

    2010-01-01

    How do publishers describe the first novels they will be releasing this spring and summer? "Amazing," "fabulous," and "unique" are words that pop up frequently, though hats off to one publicist forthright or cheeky enough to call a work "weird Western/horror." The proof of such praise is in the reading, but why not check out this preview of first…

  17. Open-Coil Retraction Spring

    Directory of Open Access Journals (Sweden)

    Pavankumar Janardan Vibhute

    2011-01-01

    Full Text Available Sliding mechanic has become a popular method for space closure with developments in preadjusted edgewise appliance. Furthermore, various space closing auxiliaries have been developed and evaluated extensively for their clinical efficiency. Their effectiveness enhanced with optimum force magnitude and low-load deflection rate (LDR/force decay. With the advent of NiTi springs in orthodontics, LDRs have been markedly reduced. For use of NiTi, clinician has to depend upon prefabricated closed coil springs. “Open Coil Retraction Spring (OCRS” is developed utilizing NiTi open-coil spring for orthodontic space closure. This paper describes fabrication and clinical application of OCRS which have number of advantages. It sustains low LDR with optimum force magnitude. Its design is adjustable for desired length and force level. It is fail-safe for both activation and deactivation (i.e., it cannot be over activated, and decompression limit of open coil is also controlled by the operator, resp.. A possibility to offset the OCRS away from mucosa helps to reduce its soft-tissue impingement.

  18. Análise cladística de Euprepina Hull (Diptera, Bombyliidae, Bombyliinae Cladistic analysis of Euprepina Hull, (Diptera, Bombyliidae, Bombyliinae

    Directory of Open Access Journals (Sweden)

    Carlos José Einicker Lamas

    1999-01-01

    Full Text Available A cladistic analysis of Euprepina Hull, 1971 (Diptera, Bombyliidae, Bombyliinae, a Neotropical genus that includes ten species, was made. The cladogram was obtained from eight studied species, based on a data matrix with 21 characters, using the program Hennig86. Character states were polarized following outgroup analysis, and an hypothetical ancestor was included in the analysis in order to root the tree. The options used, "ie*" and "xs w", resulted in four most parsimonious trees with ci = 79, ri = 80 and length 115. The monophiletism of Euprepina was supported by two synapomorphies.

  19. A general tank test of a model of the hull of the Pem-1 flying boat including a special working chart for the determination of hull performance

    Science.gov (United States)

    Dawson, John R

    1938-01-01

    The results of a general tank test of a 1/6 full-size model of the hull of the Pem-1 flying boat (N.A.C.A. model 18) are given in non-dimensional form. In addition to the usual curves, the results are presented in a new form that makes it possible to apply them more conveniently than in the forms previously used. The resistance was compared with that of N.A.C.A. models 11-C and 26(Sikorsky S-40) and was found to be generally less than the resistance of either.

  20. Archaeal Nitrification in Hot Springs

    Science.gov (United States)

    Richter, A.; Daims, H.; Reigstad, L.; Wanek, W.; Wagner, M.; Schleper, C.

    2006-12-01

    Biological nitrification, i.e. the aerobic conversion of ammonia to nitrate via nitrite, is a major component of the global nitrogen cycle. Until recently, it was thought that the ability to aerobically oxidize ammonia was confined to bacteria of the phylum Proteobacteria. However, it has recently been shown that Archaea of the phylum Crenarchaeota are also capable of ammonia oxidation. As many Crenarchaeota are thermophilic or hyperthermophilic, and at least some of them are capable of ammonia oxidation we speculated on the existence of (hyper)thermophilic ammonia-oxidizing archaea (AOA). Using PCR primers specifically targeting the archaeal ammonia monooxygenase (amoA) gene, we were indeed able to confirm the presence of such organisms in several hot springs in Reykjadalur, Iceland. These hot springs exhibited temperatures well above 80 °C and pH values ranging from 2.0 to 4.5. To proof that nitrification actually took place under these extreme conditions, we measured gross nitrification rates by the isotope pool dilution method; we added 15N-labelled nitrate to the mud and followed the dilution of the label by nitrate production from ammonium either in situ (incubation in the hot spring) or under controlled conditions in the laboratory (at 80 °C). The nitrification rates in the hot springs ranged from 0.79 to 2.22 mg nitrate-N per L of mud and day. Controls, in which microorganisms were killed before the incubations, demonstrated that the nitrification was of biological origin. Addition of ammonium increased the gross nitrification rate approximately 3-fold, indicating that the nitrification was ammonium limited under the conditions used. Collectively, our study provides evidence that (1) AOA are present in hot springs and (2) that they are actively nitrifying. These findings have major implications for our understanding of nitrogen cycling of hot environments.

  1. VSP - Discussion: The Common Interest on Planning Hulls and Plan for Collaboration Studies between NSWC and KRISO - Washington DC

    Science.gov (United States)

    2016-03-07

    planning hulls and plan for N62909-15-1-2052 collaboration studies between NSWC and KRISO - Washington DC Sb. GRANT NUMBER N62909-15-1-2052 Sc. PROGRAM...be carried out in MASK’s facilities. We discussed common interests on planing hulls, and made plans for collaboration studies between NSWC and KRISO ...Presentation of USV project in KRISO 8/19/2015 (Wed) • Discussion of common interests about planing hu lls • Planning for collaboration studies

  2. Latest Trends in the Monitoring of Ships’s Hull Underwater Part and Analysis of Its Effectiveness

    OpenAIRE

    Urbahs, A; Carjova, K; Vulans, P; Straume, R

    2012-01-01

    Ship operation is not possible without regular maintenance, inspection and certification, established by international and domestic law, where one of the main goals is an effective operation of a ship. To achieve this, it is important to reduce time and costs involved in carrying out the surveys. This paper explores the law under which it’s required for ship to have inspection of underwater part; identifies problems of ship’s hull underwater part; analyze latest trends in ship's hull underwat...

  3. Endogenous Phenolics in Hulls and Cotyledons of Mustard and Canola: A Comparative Study on Its Sinapates and Antioxidant Capacity

    OpenAIRE

    Mayengbam, Shyamchand; Aachary, Ayyappan; Thiyam-Holländer, Usha

    2014-01-01

    Endogenous sinapic acid (SA), sinapine (SP), sinapoyl glucose (SG) and canolol (CAN) of canola and mustard seeds are the potent antioxidants in various lipid-containing systems. The study investigated these phenolic antioxidants using different fractions of canola and mustard seeds. Phenolic compounds were extracted from whole seeds and their fractions: hulls and cotyledons, using 70% methanol by the ultrasonication method and quantified using HPLC-DAD. The major phenolics from both hulls and...

  4. Coefficients of Propeller-hull Interaction in Propulsion System of Inland Waterway Vessels with Stern Tunnels

    Directory of Open Access Journals (Sweden)

    Jan Kulczyk

    2014-09-01

    Full Text Available Propeller-hull interaction coefficients - the wake fraction and the thrust deduction factor - play significant role in design of propulsion system of a ship. In the case of inland waterway vessels the reliable method of predicting these coefficients in early design stage is missing. Based on the outcomes from model tests and from numerical computations the present authors show that it is difficult to determine uniquely the trends in change of wake fraction and thrust deduction factor resulting from the changes of hull form or operating conditions. Nowadays the resistance and propulsion model tests of inland waterway vessels are carried out rarely because of relatively high costs. On the other hand, the degree of development of computational methods enables’ to estimate the reliable values o interaction coefficients. The computations referred to in the present paper were carried out using the authors’ own software HPSDKS and the commercial software Ansys Fluent.

  5. Hull Formula and Standard of Compensation for Expropriation in Postcolonial States

    Directory of Open Access Journals (Sweden)

    M. Ya’kub Aiyub Kadir

    2017-08-01

    ABSTRAK: Setelah progam dekolonisasi negara-negara jajahan, salah satu isu yang mencuat dalam hukum internasional adalah perlindungan investasi asing dari nasionalisasi  negera negara baru merdeka. Dalam hal ini hull formula yang mulanya didesain oleh negara Amerika terhadap Mexico, digunakan sebagai standar kompensasi dari nasionalisasi. Dari perspektif negara negara poskolonial standar ini dianggap tidak adil, bahkan standar ini digunakan hanya untuk memperkuat dominasi negara negara penjajah di bekas jajahannya. Dengan menggunakan metodologi kajian hukum kritis, tulisan ini ingin mengkaji sejauhmana relevansi hull formula untuk diterapkan dalam konteks negara-negara poskolonial. Tulisan ini diharapkan dapat berkontribusi untuk pemahaman konsep tentang standar kompensasi terhadap nasionalisasi di negara negara poskolonial, dan dapat membuka wacana merumuskan kembali standar secara lebih fair dan adil dari perspektif  negara postkolonial.

  6. The Assessment of the Ultimate Hull Girder Strength of RO-RO Ship after Damages

    Science.gov (United States)

    Zubair Muis Alie, Muhammad; Sitepu, Ganding; Izaak Latumahin, Samuel

    2018-03-01

    Many accidents of Ro-Ro ships happen in Indonesia such as collision and grounding. When the collision or grounding takes place on the Ro-Ro ship, the ultimate strength of hull structure after damage becomes decrease. Car and passenger decks are critical location since collision and/or grounding occur. In the present study, the assessment of the ultimate hull girder strength is conducted. The cross section of Ro-Ro ship is taken to be analyzed. The collision and grounding damages are assumed to be palced on the side and bottom area, respectively. The damages are created by removing the element from the side shell and bottom part. Finally, the result obtained is compared with one another.

  7. Baking sunflower hulls within an aluminum envelope in a common laboratory oven yields charcoal.

    Science.gov (United States)

    Arnal, Pablo Maximiliano

    2015-01-01

    Charcoals have been widely used by scientist to research the removal of contaminants from water and air. One key feature of charcoal is that it keeps macropores from the parent material - though anisotropically contracted - and can even develop meso- and micropores. However, the controlled thermochemical conversion of biomass into charcoal at laboratory scale normally requires special setups which involve either vacuum or inert gas. Those setups may not be affordable in research groups or educational institutions where the research of charcoals would be highly welcome. In this work, I propose a simple and effective method to steer the thermochemical process that converts sunflower hulls (SFH) into charcoal with basic laboratory resources. The carbonization method: •Place SFH in an airtight aluminum envelope.•Thermally treat SFH within the envelope in a common laboratory oven.•Open the envelope to obtain the carbonized sunflower hulls.

  8. Efficiency measurement with a non-convex free disposal hull technology

    DEFF Research Database (Denmark)

    Fukuyama, Hirofumi; Hougaard, Jens Leth; Sekitani, Kazuyuki

    2016-01-01

    We investigate the basic monotonicity properties of least-distance (in)efficiency measures on the class of non-convex FDH (free disposable hull) technologies. We show that any known FDH least-distance measure violates strong monotonicity over the strongly (Pareto-Koopmans) efficient frontier. Tak....... Taking this result into account, we develop a new class of FDH least-distance measures that satisfy strong monotonicity and show that the developed (in)efficiency measurement framework has a natural profit interpretation.......We investigate the basic monotonicity properties of least-distance (in)efficiency measures on the class of non-convex FDH (free disposable hull) technologies. We show that any known FDH least-distance measure violates strong monotonicity over the strongly (Pareto-Koopmans) efficient frontier...

  9. A Study on the Saving Method of Plate Jigs in Hull Block Butt Welding

    Science.gov (United States)

    Ko, Dae-Eun

    2017-11-01

    A large amount of plate jigs is used for alignment of welding line and control of welding deformations in hull block assembly stage. Besides material cost, the huge working man-hours required for working process of plate jigs is one of the obstacles in productivity growth of shipyard. In this study, analysis method was proposed to simulate the welding deformations of block butt joint with plate jigs setting. Using the proposed analysis method, an example simulation was performed for actual panel block joint to investigate the saving method of plate jigs. Results show that it is possible to achieve two objectives of quality accuracy of the hull block and saving the plate jig usage at the same time by deploying the plate jigs at the right places. And the proposed analysis method can be used in establishing guidelines for the proper use of plate jigs in block assembly stage.

  10. Distribution Characterization of Leaf and Hull Pubescences and Genetic Analysis of Their Numbers in japonica Rice (Oryza sativa

    Directory of Open Access Journals (Sweden)

    Xiao-biao ZHU

    2008-12-01

    Full Text Available Distributions of pubescences on leaf blade and hull in japonica rice were observed under an optical microscope. Numbers of leaf and hull pubescences in P1, P2, F1, B1, B2 and F2 generations were investigated in three combinations of japonica rice (Sidao 10A/Wuyujing 3R, Wuyujing 3A/Sidao 10R and Liuyan 189A/HR-122, and genetic analysis for these two traits were conducted by using the joint analysis method of P1, P2, F1, B1, B2 and F2 generations with the mixed major gene plus polygene inheritance models. Leaf pubescences characterized by swollen base and fine tip distributed regularly on the boundary between dark green stripe and light green stripe of leaf blade. Hull pubescences with various lengths distributed irregularly on the whole hull. Numbers of leaf pubescences in the reciprocal combinations of Sidao 10A/Wuyujing 3R and Wuyujing 3A/Sidao 10R and numbers of hull pubescences in all the three combinations were controlled by one pair of additive major genes plus additive-dominant polygenes. In the combination of Liuyan 189A/HR-122, number of leaf pubescences was controlled by one pair of additive-dominant major genes plus additive-dominant polygenes. Both numbers of leaf and hull pubescences were mainly governed by major genes.

  11. Rice hulls a new bulking component for larval rearing of the mediterranean fruit fly, ceratitis capitata wied

    International Nuclear Information System (INIS)

    Wakid, A.M.; El-Kholy, E.M.S.; Shoman, A.A.; El-Akhdar, E.A.H.; Abdel Rahman, H.A.

    1998-01-01

    Rice hulls as a new bulking component for the larval rearing of the mediterranean fruit fly, ceratitis capitata wied. Was tested in the laboratory; and 4 formulas of rice hulls and wheat bran were evaluated biologically and financially. When rice hulls and wheat bran were mixed in the ratio of 3:1, all biological aspects and response to gamma radiation (90 Gy) of the produced adults were normal except for male fertility that decreased by about 13% of that of the bran medium (control); while male mating competitiveness was increased. When rice hulls were used without bran, only adult emergece and female fecundity were decreased by about 2% and 20%, respectively as compared to control medium (totally wheat bran); while larval duration increased by one day. The fourth formula consisting of wheat bran and rice hulls in the ratio of 1:1 showed the least favourite bulking component. Calculations showed that one million pupal production costed $26.6,22.2, 20.2 and 21.4 for the bulking ratios (hulls : bran) 0.1, 1:1, 3:1 and 1:0,respectively

  12. Influence of harvest year in the physicochemical properties and antioxidant activity of flaxseed hull oils from Tunisia

    Directory of Open Access Journals (Sweden)

    Wahid Herchi

    2015-03-01

    Full Text Available The objective of this research was to determine the effect of five years on physico-chemical characteristics and antioxidant activity of flaxseed hull oils. Oil and protein on flaxseed hull varied between 20.15 and 22.56 and 17.45 and 19.14, respectively. The albumin fraction dominated the seed hull protein composition (44 - 47%. Flaxseed hull oils showed significantly high unsaturated to saturated fatty acid ratios (6.61 - 8.36 and calculated oxidizability (Cox values (10.88 - 12.30. The physiochemical parameters determined included saponification value (SV (174 -182 mg KOH/g, unsaponifiable matter (UM (1.32 - 1.64%, peroxide value (PV (1.70 - 2.20 mequiv/kg, Oxidation value (OV (4.40 - 5.90 and oil stability (1.10 - 1.42 h. The highest content of total phenolic acids and total tocopherols were recorded on hull sample collected in 2008. Flavanoid content ranged from 11 to 19 mg/100 g oil. Antioxidant activity differed significantly; the greatest inhibition (61.38% was for the hull sample collected in 2008.

  13. Recent trend of administration on hot springs

    Energy Technology Data Exchange (ETDEWEB)

    Okubo, Shigeru [Environment Agency, Tokyo (Japan)

    1989-01-01

    The Environmental Agency exercises jurisdiction over Hot Spring Act, and plans to protect the source of the hot spring and to utilize it appropriately. From the aspect of utilization, hot springs are widely used as a means to remedy chronic diseases and tourist spots besides places for recuperation and repose. Statistics on Japanese hot springs showed that the number of hot spring spots and utilized-fountainhead increased in 1987, compared with the number in 1986. Considering the utilized-headspring, the number of naturally well-out springs has stabilized for 10 years while power-operated springs have increased. This is because the demand of hot springs has grown as the number of users has increased. Another reason is to keep the amount of hot water by setting up the power facility as the welled-out amount has decreased. Major point of recent administration on the hot spring is to permit excavation and utilization of hot springs. Designation of National hot spring health resorts started in 1954 in order to ensure the effective and original use of hot springs and to promote the public use of them, for the purpose of arranging the sound circumstances of hot springs. By 1988, 76 places were designated. 4 figs., 3 tabs.

  14. Portrait of a Geothermal Spring, Hunter's Hot Springs, Oregon.

    Science.gov (United States)

    Castenholz, Richard W

    2015-01-27

    Although alkaline Hunter's Hot Springs in southeastern Oregon has been studied extensively for over 40 years, most of these studies and the subsequent publications were before the advent of molecular methods. However, there are many field observations and laboratory experiments that reveal the major aspects of the phototrophic species composition within various physical and chemical gradients of these springs. Relatively constant temperature boundaries demark the upper boundary of the unicellular cyanobacterium, Synechococcus at 73-74 °C (the world-wide upper limit for photosynthesis), and 68-70 °C the upper limit for Chloroflexus. The upper limit for the cover of the filamentous cyanobacterium, Geitlerinema (Oscillatoria) is at 54-55 °C, and the in situ lower limit at 47-48 °C for all three of these phototrophs due to the upper temperature limit for the grazing ostracod, Thermopsis. The in situ upper limit for the cyanobacteria Pleurocapsa and Calothrix is at ~47-48 °C, which are more grazer-resistant and grazer dependent. All of these demarcations are easily visible in the field. In addition, there is a biosulfide production in some sections of the springs that have a large impact on the microbiology. Most of the temperature and chemical limits have been explained by field and laboratory experiments.

  15. Losses through gases and effluent and nutritional value of Brachiaria decumbens with addition of soybean hulls

    Directory of Open Access Journals (Sweden)

    Carlos Clayton Oliveira Dantas

    2014-05-01

    Full Text Available The objective of this experiment was to evaluate the losses of nutrient through gases and effluents, the nutrient recovery, fermentation parameters and the chemical parameters of silages of Brachiaria decumbens with the addition of soybean hulls, testing five levels of inclusion: 0, 10, 20, 30 and 40% (as is, with five replications per treatment. After the standardization cut of the forage, performed at 5 cm from the soil level, the soil was fertilized with nitrogen and potassium in the form of ammonium sulfate and potassium chloride, respectively, at 60 kg/ha. After 60 days, the grass was cut at 10 cm from the soil and ensiled. Experimental silos with capacity of 10 liters with Bunsen valve were used. Silos had 3 kg of sand conditioned at the bottom for retention of the effluents. The results show that the contents of dry matter, crude protein, acid detergent insoluble fiber and total digestible nutrients presented positive linear behavior with the inclusion of soybean hulls. In the grass silages with addition of soybean hulls, there was greater recovery of dry matter in relation to the control silage, which is a reflection of the negative linear behavior for the values of losses of gases and effluent. There was quadratic behavior in the pH values and negative linear behavior for the ammonia N values and buffering capacity with the inclusion of the additive in the grass silage. Inclusion of soybean hulls is sufficient to improve the fermentation pattern and minimize the losses through gases and effluents, contributing to the nutrient recovery, in addition to promoting overall improvement of the nutritional value of Brachiaria grass silages.

  16. Design of high-speed planing hulls for the improvement of resistance and seakeeping performance

    Directory of Open Access Journals (Sweden)

    Dong Jin Kim

    2013-03-01

    Full Text Available High-speed vessels require good resistance and seakeeping performance for safe operations in rough seas. The resistance and seakeeping performance of high-speed vessels varies significantly depending on their hull forms. In this study, three planing hulls that have almost the same displacement and principal dimension are designed and the hydrodynamic characteristics of those hulls are estimated by high-speed model tests. All model ships are deep-V type planing hulls. The bows of no.2 and no.3 model ships are designed to be advantageous for wave-piercing in rough water. No. 2 and no. 3 model ships have concave and straight forebody cross-sections, respectively. And length-to-beam ratios of no.2 and no.3 models are larger than that of no.1 model. In calm water tests, running attitude and resistance of model ships are measured at various speeds. And motion tests in regular waves are performed to measure the heave and pitch motion responses of the model ships. The required power of no.1 (VPS model is smallest, but its vertical motion amplitudes in waves are the largest. No.2 (VWC model shows the smallest motion amplitudes in waves, but needs the greatest power at high speed. The resistance and seakeeping performance of no.3 (VWS model ship are the middle of three model ships, respectively. And in regular waves, no.1 model ship experiences ‘fly over’ phenomena around its resonant frequency. Vertical accelerations at specific locations such as F.P., center of gravity of model ships are measured at their resonant frequency. It is necessary to measure accelerations by accelerometers or other devices in model tests for the accurate prediction of vertical accelerations in real ships.

  17. Dynamics Analysis of Castor Hulling in the Process of Air-and-Screen Cleaning

    Directory of Open Access Journals (Sweden)

    Gao Ruitao

    2016-01-01

    Full Text Available The air-and-screen cleaning mechanism of castor hulling is analyzed in this paper. And the numeric expression equations of the castor dynamics analysis are established. The correlation of floating speeds vp, air speeds w, the direction angle of airflow velocity β, the direction angle of vibration δ, the friction angle ϕ, the slip coefficient, the fell coefficient and the jumping coefficient are analyzed.

  18. Dynamics Analysis of Castor Hulling in the Process of Air-and-Screen Cleaning

    OpenAIRE

    Gao Ruitao; Cao Yuhua; Yao Liangliang; Jin Hong

    2016-01-01

    The air-and-screen cleaning mechanism of castor hulling is analyzed in this paper. And the numeric expression equations of the castor dynamics analysis are established. The correlation of floating speeds vp, air speeds w, the direction angle of airflow velocity β, the direction angle of vibration δ, the friction angle ϕ, the slip coefficient, the fell coefficient and the jumping coefficient are analyzed.

  19. Visualizing RNA Secondary Structure Base Pair Binding Probabilities using Nested Concave Hulls

    OpenAIRE

    Sansen , Joris; Bourqui , Romain; Thebault , Patricia; Allali , Julien; Auber , David

    2015-01-01

    International audience; The challenge 1 of the BIOVIS 2015 design contest consists in designing an intuitive visual depiction of base pairs binding probabilities for secondary structure of ncRNA. Our representation depicts the potential nucleotide pairs binding using nested concave hulls over the computed MFE ncRNA secondary structure. Thus, it allows to identify regions with a high level of uncertainty in the MFE computation and the structures which seem to match to reality.

  20. Properties of Moldings Prepared from LDPE-Pumpkin Seed Hulls Blend

    Directory of Open Access Journals (Sweden)

    Karolina Głogowska

    2017-12-01

    Full Text Available In recent decades, standard polymer blends for different applications have been more and more often replaced by blends containing raw materials. The use of natural materials as filler in thermoplastics brings both economic and environmental benefits. The use of a given vegetable filler depends on the geographic location and natural occurrence of the vegetables in a given geographic region. In Poland, for instance, the pumpkin is one of such vegetables. They are used for producing oil which is pressed from pumpkin seeds. Pumpkin seeds are then collected, dried and purified to produce waste material in hull form. Particles of ground pumpkin seed hulls with varying sizes and weight-in-weight concentration ranging from 0% to 20% relative to the matrix are used as filler in low-density polyethylene. Pumpkin seed hulls are ground and sieved. Four fractions of hulls with different particle sizes are produced: <0.2mm, 0.2mm-0.4mm, 0.4mm-0.6mm, 0.6mm-0.8mm. The paper reports the results of investigation of the mechanical properties, i.e., strength properties determined by static tensile testing and hardness measurement, of injection molds produced at constant processing parameters. In addition, the cross sections of the obtained products are subjected to microscopic examination. Relationships are determined between tensile modulus, maximum tensile stress, tensile stress at yield, maximum tensile strain, tensile strain at yield as well as Shore hardness and weigh-in-weight concentration of the powdered natural filler and its grain sizes. Finally, relevant conclusions are drawn.

  1. Design of a High Speed Planing Hull with a Cambered Step and Surface Piercing Hydrofoils

    Science.gov (United States)

    2014-06-01

    Impact Acceleration (Hoggard and Jones) - 1/10 highest eta_110_CG = 7.0*( H13 /Bpx)*(1+Tau/2...hulls with a higher deadrise angle perform better, with improved ride quality as the impact of wave is reduced. However, there is a disadvantage...the previous studies of Blount, Codega and Savitsky, a planing hull’s running trim angle and associated lift coefficient has a large impact on dynamic

  2. An algorithm for computing the hull of the solution set of interval linear equations

    Czech Academy of Sciences Publication Activity Database

    Rohn, Jiří

    2011-01-01

    Roč. 435, č. 2 (2011), s. 193-201 ISSN 0024-3795 R&D Projects: GA ČR GA201/09/1957; GA ČR GC201/08/J020 Institutional research plan: CEZ:AV0Z10300504 Keywords : interval linear equations * solution set * interval hull * algorithm * absolute value inequality Subject RIV: BA - General Mathematics Impact factor: 0.974, year: 2011

  3. Comparison of Grain Yield and Some Characteristics of Hulled, Durum and Bread Wheat Genotypes Varieties

    Directory of Open Access Journals (Sweden)

    Bekir Atar

    2017-02-01

    Full Text Available In spite of the low grain yield they produce, the hulled wheat have become even more important in recent years because of their resistance to negative environmental conditions and healthy nutritional content. The research was carry out in order to comparison the yield and yield characteristics of durum (Kiziltan-91 and C-1252, hulled (Einkorn and Emmer and bread wheat (Tir varieties in Isparta ecological conditions in 2013-14 and 2014-15 vegetation periods. In both years, the highest grain yield was obtained in Kiziltan-91 variety (3992 and 3758 kg ha-1 respectively. The grain yield of hulled wheats in the first year (Einkorn 1269 kg ha-1, Emmer 2125 kg ha-1 was around Turkey averages. However, grain yield decreased of commercial wheat varieties due to the negative effect of high amount of rainfall in June in the second year, but considerably increased in (Einkorn 2150 kg ha-1, Emmer 2533 kg ha-1. N uptake was found to be lower in the than durum wheats. In terms of grain protein content, the highest values were obtained in Emmer variety (16.4%-15.3%.

  4. Automatic Generation of the Planning Tunnel High Speed Craft Hull Form

    Institute of Scientific and Technical Information of China (English)

    Morteza Ghassabzadeh; Hassan Ghassemi

    2012-01-01

    The creation of geometric model of a ship to determine the characteristics of hydrostatic and hydrodynamic,and also for structural design and equipments arrangement are so important in the ship design process.Planning tunnel high speed craft is one of the crafts in which,achievement to their top speed is more important.These crafts with the use of tunnel have the aero-hydrodynamics properties to diminish the resistance,good sea-keeping behavior,reduce slamming and avoid porpoising.Because of the existence of the tunnel,the hull form generation of these crafts is more complex and difficult.In this paper,it has attempted to provide a method based on geometry creation guidelines and with an entry of the least control and hull form adjustment parameters,to generate automatically the hull form of planning tunnel craft.At first,the equations of mathematical model are described and subsequent,three different models generated based on present method are compared and analyzed.Obviously,the generated model has more application in the early stages of design.

  5. Bow hull-form optimization in waves of a 66,000 DWT bulk carrier

    Directory of Open Access Journals (Sweden)

    Jin-Won Yu

    2017-09-01

    Full Text Available This paper uses optimization techniques to obtain bow hull form of a 66,000 DWT bulk carrier in calm water and in waves. Parametric modification functions of SAC and section shape of DLWL are used for hull form variation. Multi-objective functions are applied to minimize the wave-making resistance in calm water and added resistance in regular head wave of λ/L = 0.5. WAVIS version 1.3 is used to obtain wave-making resistance. The modified Fujii and Takahashi's formula is applied to obtain the added resistance in short wave. The PSO algorithm is employed for the optimization technique. The resistance and motion characteristics in calm water and regular and irregular head waves of the three hull forms are compared. It has been shown that the optimal brings 13.2% reduction in the wave-making resistance and 13.8% reduction in the added resistance at λ/L = 0.5; and the mean added resistance reduces by 9.5% at sea state 5.

  6. Rice Hull Extract Suppresses Benign Prostate Hyperplasia by Decreasing Inflammation and Regulating Cell Proliferation in Rats.

    Science.gov (United States)

    Kim, Chae-Yun; Chung, Kyung-Sook; Cheon, Se-Yun; Lee, Jong-Hyun; Park, Youn-Bum; An, Hyo-Jin

    2016-08-01

    Even though rice hull has various physiological functions with high antioxidant potential, the molecular mechanism(s) underlying the effects of rice hull on benign prostatic hyperplasia (BPH) have not been evaluated. The aim of this study was to determine the protective effect of rice hull water extract (RHE) against BPH, which is a common disorder in elderly men and involves inflammation that induces an imbalance between cell proliferation and cell death. In this study, RHE-treated mice exhibited lower prostate weights and ratios of prostate weight to body weight compared to those for the BPH-induced group. In addition, RHE-treated mice had lower serum levels of dihydrotestosterone, mRNA expression of 5α-reductase2, and protein expressions of proliferating cell nuclear antigen (PCNA). Furthermore, RHE treatment significantly decreased cell proliferation by regulating the expression levels of inflammatory-related proteins (iNOS and COX-2) and apoptosis-associated proteins (Fas, FADD, procaspase-8, -3, and Bcl-2 family proteins). These results suggest that RHE could protect against the development of BPH through its anti-inflammatory and apoptotic properties and has good potential as a treatment for BPH.

  7. Visual hull method for tomographic PIV measurement of flow around moving objects

    Energy Technology Data Exchange (ETDEWEB)

    Adhikari, D.; Longmire, E.K. [University of Minnesota, Department of Aerospace Engineering and Mechanics, Minneapolis, MN (United States)

    2012-10-15

    Tomographic particle image velocimetry (PIV) is a recently developed method to measure three components of velocity within a volumetric space. We present a visual hull technique that automates identification and masking of discrete objects within the measurement volume, and we apply existing tomographic PIV reconstruction software to measure the velocity surrounding the objects. The technique is demonstrated by considering flow around falling bodies of different shape with Reynolds number {proportional_to}1,000. Acquired image sets are processed using separate routines to reconstruct both the volumetric mask around the object and the surrounding tracer particles. After particle reconstruction, the reconstructed object mask is used to remove any ghost particles that otherwise appear within the object volume. Velocity vectors corresponding with fluid motion can then be determined up to the boundary of the visual hull without being contaminated or affected by the neighboring object velocity. Although the visual hull method is not meant for precise tracking of objects, the reconstructed object volumes nevertheless can be used to estimate the object location and orientation at each time step. (orig.)

  8. Anti-Melanogenic Activity and Cytotoxicity of Pistacia vera Hull on Human Melanoma SKMEL-3 Cells.

    Science.gov (United States)

    Sarkhail, Parisa; Salimi, Mona; Sarkheil, Pantea; Mostafapour Kandelous, Hirsa

    2017-07-01

    Pistacia vera seed is a common food and medicinal seed in Iran. It's hull (outer skin) as a significant byproduct of pistachio, is traditionally used as tonic, sedative and antidiarrheal and has been shown to be a rich source of antioxidants. The aim of the present study is to evaluate the anti-melanogenic activity of the pistachio hulls in order to discover a new alternative herbal agent to treat skin hyperpigmentation disorders. In this work, antioxidant and anti-tyrosinase activity of MeOH extract from Pistacia vera hull (MPH) were evaluated in vitro, respectively, by DPPH radical scavenging and mushroom tyrosinase activity assays. Then the effect of MPH on the melanin content, cellular tyrosinase activity and cytotoxicity (MTT assay) on human melanoma SKMEL-3 cell were determined followed by 72 h incubation. The results indicated that MPH had valuable DPPH radical scavenging effect and weak anti-tyrosinase activity when compared to the well-known antioxidant (BHT) and tyrosinase inhibitor (kojic acid), respectively. MPH, at a high dose (0.5 mg/mL), showed significant cytotoxic activity (~63%) and strong anti-melanogenic effect (~57%) on SKMEL-3 cells. The effect of MPH in the reduction of melanin content may be related to its cytotoxicity. The results obtained suggest that MPH can be used as an effective agent in the treatment of some skin hyperpigmentation disorders such as melanoma.

  9. Investigation of 144Pr measurements for determination of residual Pu in FBR leached hulls

    International Nuclear Information System (INIS)

    Yates, A.; Bremner, W.B.

    1983-12-01

    The measurement of plutonium in leached hulls arising from FBR fuel reprocessing is required for plant control, accountancy and safeguards. At DNPDE these measurements are carried out on the batch of hulls prior to bulking into 200 l drums for retrievable storage and ultimately further treatment for plutonium recovery. The experience to date has related to the use of neutron interrogation using sealed tube neutron generators as the irradiation source. The supply of replacement sealed tubes has become difficult. It was therefore decided to consider, amongst other techniques, the measurement of 144 Pr gamma emission as a possible alternative. The technique has been extensively used for thermal reactor fuels on a routine basis. There has also been a limited amount of work reported from Cap La Hague on applying the technique to FBR fuels as part of an experimental programme. This paper therefore describes the work done at DNPDE which evaluated the technique for use on a batch of hulls arising from a PFR fuel reprocessing campaign. (author)

  10. Countercurrent extraction of soluble sugars from almond hulls and assessment of the bioenergy potential.

    Science.gov (United States)

    Holtman, Kevin M; Offeman, Richard D; Franqui-Villanueva, Diana; Bayati, Andre K; Orts, William J

    2015-03-11

    Almond hulls contain considerable proportions (37% by dry weight) of water-soluble, fermentable sugars (sucrose, glucose, and fructose), which can be extracted for industrial purposes. The maximum optimal solids loading was determined to be 20% for sugar extraction, and the addition of 0.5% (w/v) pectinase aided in maintaining a sufficient free water volume for sugar recovery. A laboratory countercurrent extraction experiment utilizing a 1 h steep followed by three extraction (wash) stages produced a high-concentration (131 g/L fermentable sugar) syrup. Overall, sugar recovery efficiency was 88%. The inner stage washing efficiencies were compatible with solution equilibrium calculations, indicating that efficiency was high. The concentrated sugar syrup was fermented to ethanol at high efficiency (86% conversion), and ethanol concentrations in the broth were 7.4% (v/v). Thin stillage contained 233 g SCOD/L, which was converted to biomethane at an efficiency of 90% with a biomethane potential of 297 mL/g SCODdestroyed. Overall, results suggested that a minima of 49 gal (185 L) ethanol and 75 m(3) methane/t hulls (dry whole hull basis) are achievable.

  11. Fluid dynamic interface between hull and hydrofoil; Sentai to suichuyoku no ryutai rikigakuteki kansho ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kataoka, K; Ando, J; Nakatake, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-04-10

    For the high-speed ship with hydrofoil, it is important to grasp the mutual interference between its hydrofoil and hull. In this study, effects of the state of hydrofoils and velocity on the hull were fluid-dynamically investigated through the numerical calculation by means of Rankine source method using a Wigley model with two hydrofoils. Before considering the model with hydrofoils, the attitude change of a hull without hydrofoils during traveling in high-speed was examined. For the high-speed ship, various measuring systems have been conceived due to the large change in its attitude. The Wigley model has been used for the numerical calculation when considering the attitude change in the medium- and low-speed regions. In this study, resistance tests without constraining the sinkage and trim were conducted using a Wigley model in the high-speed region around Fn=1.0, which have not been usually conducted. The attitude changes were compared with the numerical calculation results by the Rankine source method. The wave making resistance and attitude change of the Wigley model with hydrofoils were also calculated. 12 refs., 10 figs.

  12. GOLD HULL AND INTERNODE2 encodes a primarily multifunctional cinnamyl-alcohol dehydrogenase in rice.

    Science.gov (United States)

    Zhang, Kewei; Qian, Qian; Huang, Zejun; Wang, Yiqin; Li, Ming; Hong, Lilan; Zeng, Dali; Gu, Minghong; Chu, Chengcai; Cheng, Zhukuan

    2006-03-01

    Lignin content and composition are two important agronomic traits for the utilization of agricultural residues. Rice (Oryza sativa) gold hull and internode phenotype is a classical morphological marker trait that has long been applied to breeding and genetics study. In this study, we have cloned the GOLD HULL AND INTERNODE2 (GH2) gene in rice using a map-based cloning approach. The result shows that the gh2 mutant is a lignin-deficient mutant, and GH2 encodes a cinnamyl-alcohol dehydrogenase (CAD). Consistent with this finding, extracts from roots, internodes, hulls, and panicles of the gh2 plants exhibited drastically reduced CAD activity and undetectable sinapyl alcohol dehydrogenase activity. When expressed in Escherichia coli, purified recombinant GH2 was found to exhibit strong catalytic ability toward coniferaldehyde and sinapaldehyde, while the mutant protein gh2 completely lost the corresponding CAD and sinapyl alcohol dehydrogenase activities. Further phenotypic analysis of the gh2 mutant plants revealed that the p-hydroxyphenyl, guaiacyl, and sinapyl monomers were reduced in almost the same ratio compared to the wild type. Our results suggest GH2 acts as a primarily multifunctional CAD to synthesize coniferyl and sinapyl alcohol precursors in rice lignin biosynthesis.

  13. GOLD HULL AND INTERNODE2 Encodes a Primarily Multifunctional Cinnamyl-Alcohol Dehydrogenase in Rice1

    Science.gov (United States)

    Zhang, Kewei; Qian, Qian; Huang, Zejun; Wang, Yiqin; Li, Ming; Hong, Lilan; Zeng, Dali; Gu, Minghong; Chu, Chengcai; Cheng, Zhukuan

    2006-01-01

    Lignin content and composition are two important agronomic traits for the utilization of agricultural residues. Rice (Oryza sativa) gold hull and internode phenotype is a classical morphological marker trait that has long been applied to breeding and genetics study. In this study, we have cloned the GOLD HULL AND INTERNODE2 (GH2) gene in rice using a map-based cloning approach. The result shows that the gh2 mutant is a lignin-deficient mutant, and GH2 encodes a cinnamyl-alcohol dehydrogenase (CAD). Consistent with this finding, extracts from roots, internodes, hulls, and panicles of the gh2 plants exhibited drastically reduced CAD activity and undetectable sinapyl alcohol dehydrogenase activity. When expressed in Escherichia coli, purified recombinant GH2 was found to exhibit strong catalytic ability toward coniferaldehyde and sinapaldehyde, while the mutant protein gh2 completely lost the corresponding CAD and sinapyl alcohol dehydrogenase activities. Further phenotypic analysis of the gh2 mutant plants revealed that the p-hydroxyphenyl, guaiacyl, and sinapyl monomers were reduced in almost the same ratio compared to the wild type. Our results suggest GH2 acts as a primarily multifunctional CAD to synthesize coniferyl and sinapyl alcohol precursors in rice lignin biosynthesis. PMID:16443696

  14. Mathematical model of small water-plane area twin-hull and application in marine simulator

    Science.gov (United States)

    Zhang, Xiufeng; Lyu, Zhenwang; Yin, Yong; Jin, Yicheng

    2013-09-01

    Small water-plane area twin-hull (SWATH) has drawn the attention of many researchers due to its good sea-keeping ability. In this paper, MMG's idea of separation was used to perform SWATH movement modeling and simulation; respectively the forces and moment of SWATH were divided into bare hull, propeller, rudder at the fluid hydrodynamics, etc. Wake coefficient at the propellers which reduces thrust coefficient, and rudder mutual interference forces among the hull and propeller, for the calculation of SWATH, were all considered. The fourth-order Runge-Kutta method of integration was used by solving differential equations, in order to get SWATH's movement states. As an example, a turning test at full speed and full starboard rudder of `Seagull' craft is shown. The simulation results show the SWATH's regular pattern and trend of motion. It verifies the correctness of the mathematical model of the turning movement. The SWATH's mathematical model is applied to marine simulator in order to train the pilots or seamen, or safety assessment for ocean engineering project. Lastly, the full mission navigation simulating system (FMNSS) was determined to be a successful virtual reality technology application sample in the field of navigation simulation.

  15. Adsorption of reactive blue BF-5G dye by soybean hulls: kinetics, equilibrium and influencing factors.

    Science.gov (United States)

    Honorio, Jacqueline Ferandin; Veit, Márcia Teresinha; Gonçalves, Gilberto da Cunha; de Campos, Élvio Antonio; Fagundes-Klen, Márcia Regina

    2016-01-01

    The textile industry is known for the high use of chemicals, such as dyes, and large volumes of effluent that contaminate waters, a fact that has encouraged research and improved treatment techniques. In this study, we used unprocessed soybean hulls for the removal of reactive blue BF-5G dye. The point of zero charge of soybean hulls was 6.76. Regarding the speed of agitation in the adsorption process, the resistance to mass transfer that occurs in the boundary layer was eliminated at 100 rpm. Kinetics showed an experimental amount of dye adsorbed at equilibrium of 57.473 mg g(-1) obtained under the following conditions: dye initial concentration = 400 mg L(-1); diameter of particle = 0.725 mm; dosage = 6 g L(-1); pH 2; 100 rpm; temperature = 30 °C; and duration of 24 hours. The pseudo-second order best showed the dye removal kinetics. The adsorption isotherms performed at different temperatures (20, 30, 40 and 50 °C) showed little variation in the concentration range assessed, being properly adjusted by the Langmuir isotherm model. The maximum capacity of dye adsorption was 72.427 mg g(-1) at 30 °C. Since soybean hull is a low-cost industrial byproduct, it proved to be a potential adsorbent for the removal of the textile dye assessed.

  16. Liquid nitrogen pretreatment of eucalyptus sawdust and rice hull for enhanced enzymatic saccharification.

    Science.gov (United States)

    Castoldi, Rafael; Correa, Vanesa G; de Morais, Gutierrez Rodrigues; de Souza, Cristina G M; Bracht, Adelar; Peralta, Rosely A; Peralta-Muniz Moreira, Regina F; Peralta, Rosane M

    2017-01-01

    In this work, liquid nitrogen was used for the first time in the pretreatment of plant biomasses for purposes of enzymatic saccharification. After treatment (cryocrushing), the initial rates of the enzymatic hydrolysis of eucalyptus sawdust and rice hull were increased more than ten-fold. Cryocrushing did not modify significantly the contents of cellulose, hemicellulose and lignin in both eucalyptus sawdust and rice hulls. However, substantial disorganization of the lignocellulosic materials in consequence of the pretreatment could be observed by electron microscopy. Cryocrushing was highly efficient in improving the saccharification of the holocellulose component of the plant biomasses (from 4.3% to 54.1% for eucalyptus sawdust and from 3.9% to 40.6% for rice hull). It is important to emphasize that it consists in a simple operation with low requirements of water and chemicals, no corrosion, no release of products such as soluble phenolics, furfural and hydroxymethylfurfural and no waste generation. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. PIXE Analysis of Metal Hull Bolts From HMB DeBraak

    International Nuclear Information System (INIS)

    Correll, Francis D.; Cole, Lord K.; Slater, Charles J.; Vanhoy, Jeffrey R.; Fithian, Charles H.

    2009-01-01

    HMB DeBraak was a 16-gun British brig-sloop that sank in a squall on May 25, 1798 off Cape Henlopen, Delaware. Silt covered the wooden hull shortly after it sank, preserving it until DeBraak was raised in 1986. The items recovered from the ship include metal bolts that held the hull together. We used PIXE to measure the compositions of 45 of the bolts and found that they are nearly pure copper (98.3% on average), with most also containing small amounts of iron (0.87%), nickel (0.039%), arsenic (0.43%), silver (0.089%), lead (0.18%), and bismuth (0.12%). A few contain a little indium, tin, or antimony, but none contain zinc above the quantization level. The compositions are similar to those reported for 18th-century English copper, but different from several copper alloys also used to make hull bolts. We conclude that, when DeBraak was last fitted out in 1795-1797, the Royal Navy was still using bolts similar to William Forbes's mechanically hardened pure copper bolts. Forbes's process represents the successful innovation and application of new technology in Royal Navy ships during the wars of the late 18th century.

  18. PIXE Analysis of Metal Hull Bolts From HMB DeBraak

    Science.gov (United States)

    Correll, Francis D.; Cole, Lord K.; Slater, Charles J.; Vanhoy, Jeffrey R.; Fithian, Charles H.

    2009-03-01

    HMB DeBraak was a 16-gun British brig-sloop that sank in a squall on May 25, 1798 off Cape Henlopen, Delaware. Silt covered the wooden hull shortly after it sank, preserving it until DeBraak was raised in 1986. The items recovered from the ship include metal bolts that held the hull together. We used PIXE to measure the compositions of 45 of the bolts and found that they are nearly pure copper (98.3% on average), with most also containing small amounts of iron (0.87%), nickel (0.039%), arsenic (0.43%), silver (0.089%), lead (0.18%), and bismuth (0.12%). A few contain a little indium, tin, or antimony, but none contain zinc above the quantization level. The compositions are similar to those reported for 18th-century English copper, but different from several copper alloys also used to make hull bolts. We conclude that, when DeBraak was last fitted out in 1795-1797, the Royal Navy was still using bolts similar to William Forbes's mechanically hardened pure copper bolts. Forbes's process represents the successful innovation and application of new technology in Royal Navy ships during the wars of the late 18th century.

  19. Isoprene Production on Enzymatic Hydrolysate of Peanut Hull Using Different Pretreatment Methods

    Directory of Open Access Journals (Sweden)

    Sumeng Wang

    2016-01-01

    Full Text Available The present study is about the use of peanut hull for isoprene production. In this study, two pretreatment methods, hydrogen peroxide-acetic acid (HPAC and popping, were employed prior to enzymatic hydrolysis, which could destroy the lignocellulosic structure and accordingly improve the efficiency of enzymatic hydrolysis. It is proven that the isoprene production on enzymatic hydrolysate with HPAC pretreatment is about 1.9-fold higher than that of popping pretreatment. Moreover, through High Performance Liquid Chromatography (HPLC analysis, the amount and category of inhibitors such as formic acid, acetic acid, and HMF were assayed and were varied in different enzymatic hydrolysates, which may be the reason leading to a decrease in isoprene production during fermentation. To further increase the isoprene yield, the enzymatic hydrolysate of HPAC was detoxified by activated carbon. As a result, using the detoxified enzymatic hydrolysate as the carbon source, the engineered strain YJM21 could accumulate 297.5 mg/L isoprene, which accounted for about 90% of isoprene production by YJM21 fermented on pure glucose (338.6 mg/L. This work is thought to be the first attempt on isoprene production by E. coli using peanut hull as the feedstock. More importantly, it also shows the prospect of peanut hull to be considered as an alternative feedstock for bio-based chemicals or biofuels production due to its easy access and high polysaccharide content.

  20. Chemical decontamination and melt densification of chop-leach fuel hulls

    International Nuclear Information System (INIS)

    Dillon, R.L.; Griggs, B.; Kemper, R.S.; Nelson, R.G.

    1976-01-01

    This paper reports on decontamination and densification studies of chop-leach fuel hull residues designed to minimize the transuranic element (TRU) contaminated waste stream. Decontamination requirements have been established from studies of TRU element distribution in the fuel hull residues. Effective surface decontamination of Zircaloy requires removal of zirconium oxide corrosion products. Good decontamination factors have been achieved with aqueous solutions following high temperature HF conditioning of oxide films. Molten fluoride salt mixtures are effective decontaminants, but pose problems in metal loss and salt dragout. Molten metal decontamination methods are highly preliminary, but may be required to reduce TRU originating from tramp uranium in Zircaloy. Low melting (1300 0 C) alloy of Zircaloy, stainless steel, and Inconel have been prepared in induction heated graphite crucibles. High quality ingots of Zircaloy-2 have been prepared directly from short sections of descaled fuel clad tubing using the Inductoslag process. This material is readily capable of refabrication. Inductoslag melts have also been prepared from heavily oxidized Zircaloy tubing demonstrating melt densification without prior decontamination is technically feasible. Hydrogen absorption kinetics have been demonstrated with cast Zircaloy-2 and cast Zircaloy-stainless steel-Inconel alloys. Metallic fuel hull residues have been proposed as a storage medium for tritium released from fuel during reprocessing. (author)