Turbo-machine deployment of HTR-10 GT

International Nuclear Information System (INIS)

Zhu Shutang; Wang Jie; Zhang Zhengming; Yu Suyuan

2005-01-01

As a testing project of gas turbine modular High Temperature Gas-cooled Reactor (HTGR), HTR-10GT has been studied and developed by Institute of Nuclear and New Energy Technology (INET) of Tsinghua University after the success of HTR-10 with steam turbine cycle. The main purposes of this project are to demonstrate the gas turbine modular HTGR, to optimize the deployment of Power Conversion Unit (PCU) and to verify the techniques of turbo-machine, operating modes and controlling measures. HTR-10GT is concentrated on the PCU design and the turbo-machine deployment. Possible turbo-machine deployments have been investigated and two of them are introduced in this paper. The preliminary design for the turbo-machine of HTR-10GT is single-shaft of vertical layout, arranged by the side of the reactor and the turbo-compressor rotary speed was selected to be 250 s -1 (15000 r/min) by considering the efficiency of turbo-compressor blade systems, the strength conditions and the mass and size characteristics of the turbo-compressor. The rotor system will be supported by electromagnetic bearings (EMBs) to curb the possible pollutions of the primary loop. Of all the components in this design, the high speed turbo-generator seems to be a world-wide technical nut. As an alternative design, a gearbox complex is used to reduce the rotary speed from the turbo-compressor 250 s -1 to 50 s -1 so that the ordinary generator can be used. (authors)

Neutron Fluence And DPA Rate Analysis In Pebble-Bed HTR Reactor Vessel Using MCNP

Science.gov (United States)

Hamzah, Amir; Suwoto; Rohanda, Anis; Adrial, Hery; Bakhri, Syaiful; Sunaryo, Geni Rina

2018-02-01

In the Pebble-bed HTR reactor, the distance between the core and the reactor vessel is very close and the media inside are carbon and He gas. Neutron moderation capability of graphite material is theoretically lower than that of water-moderated reactors. Thus, it is estimated much more the fast neutrons will reach the reactor vessel. The fast neutron collisions with the atoms in the reactor vessel will result in radiation damage and could be reducing the vessel life. The purpose of this study was to obtain the magnitude of neutron fluence in the Pebble-bed HTR reactor vessel. Neutron fluence calculations in the pebble-bed HTR reactor vessel were performed using the MCNP computer program. By determining the tally position, it can be calculated flux, spectrum and neutron fluence in the position of Pebble-bed HTR reactor vessel. The calculations results of total neutron flux and fast neutron flux in the reactor vessel of 1.82x108 n/cm2/s and 1.79x108 n/cm2/s respectively. The fast neutron fluence in the reactor vessel is 3.4x1017 n/cm2 for 60 years reactor operation. Radiation damage in stainless steel material caused by high-energy neutrons (> 1.0 MeV) will occur when it has reached the neutron flux level of 1.0x1024 n/cm2. The neutron fluence results show that there is no radiation damage in the Pebble-bed HTR reactor vessel, so it is predicted that it will be safe to operate at least for 60 years.

Calculation of HTR-10 first criticality with MVP

International Nuclear Information System (INIS)

Xie Jiachun; Yao Lianying

2015-01-01

The first criticality of 10 MW pebble-bed high temperature gas-cooled reactor-test module (HTR-10) was calculated with MVP. According to the characteristics of HTR-10, the Statistical Geometry Model of MVP was employed to describe the random arrangement of coated fuel particles in the fuel pebbles and the random distribution of the fuel and dummy pebbles in the core. Compared with previous results from VSOP and MCNP, the MVP results with JENDL-3.3 library were little more different, but the results with ENDF/B-Ⅵ.8 library were very close. The relative errors were less than 0.7%, compared with the first criticality experimental results. The study shows that MVP could be used in the physics calculations for pebble bed high temperature gas-cooled reactors. (authors)

Study on the production mechanism of Co-60 in the primary loop of HTR-10

International Nuclear Information System (INIS)

Wang Shouang; Xie Feng; Li Hong; Cao Jianzhu; Li Fu; Wei Liqiang

2015-01-01

Co-60 is an activated metallic erosion product, which is very important for waste management and decommissioning work of pressurized water reactor (PWR) power plants. Recent measurement on the samples from the primary loop of HTR-10 indicates the existence of Co-60. In current paper, the preliminary experimental results in HTR-10 will be introduced, and the production mechanism of Co-60 in the pebble bed high temperature gas-cooled reactors will be summarized and compared with that in PWRs and Germany High Temperature Nuclear Reactor (AVR). The further experiments with decomposing the post-irradiation graphite spheres of HTR-10 are put forward, which will promote the further study to testify the production sources of Co-60 and be of great significance in the waste minimization and the decommissioning work of HTR-10. (author)

Fuel management of HTR-10

International Nuclear Information System (INIS)

Wu Zongxin; Jing Xingqing

2001-01-01

The 10 MW high temperature cooled reactor (HTR-10) built in Tsinghua University is a pebble bed type of HTGR. The continuous recharge and multiple-pass of spherical fuel elements are used for fuel management. The initiative stage of core is composed of the mix of spherical fuel elements and graphite elements. The equilibrium stage of core is composed of identical spherical fuel elements. The fuel management during the transition from the initiative stage to the equilibrium stage is a key issue for HTR-10 physical design. A fuel management strategy is proposed based on self-adjustment of core reactivity. The neutron physical code is used to simulate the process of fuel management. The results show that the graphite elements, the recharging fuel elements below the burn-up allowance, and the discharging fuel elements over the burn-up allowance could be identified by burn-up measurement. The maximum of burn-up fuel elements could be controlled below the burn-up limit

Potentialities of high temperature reactors (HTR)

International Nuclear Information System (INIS)

Hittner, D.

2001-01-01

This articles reviews the assets of high temperature reactors concerning the amount of radioactive wastes produced. 2 factors favors HTR-type reactors: high thermal efficiency and high burn-ups. The high thermal efficiency is due to the high temperature of the coolant, in the case of the GT-MHR project (a cooperation between General Atomic, Minatom, Framatome, and Fuji Electric) designed to burn Russian military plutonium, the expected yield will be 47% with an outlet helium temperature of 850 Celsius degrees. The high temperature of the coolant favors a lot of uses of the heat generated by the reactor: urban heating, chemical processes, or desalination of sea water.The use of a HTR-type reactor in a co-generating way can value up to 90% of the energy produced. The high burn-up is due to the technology of HTR-type fuel that is based on encapsulation of fuel balls with heat-resisting materials. The nuclear fuel of Fort-Saint-Vrain unit (Usa) has reached values of burn-ups from 100.000 to 120.000 MWj/t. It is shown that the quantity of unloaded spent fuel can be divided by 4 for the same amount of electricity produced, in the case of the GT-MHR project in comparison with a light water reactor. (A.C.)

Analysis on First Criticality Benchmark Calculation of HTR-10 Core

International Nuclear Information System (INIS)

Zuhair; Ferhat-Aziz; As-Natio-Lasman

2000-01-01

HTR-10 is a graphite-moderated and helium-gas cooled pebble bed reactor with an average helium outlet temperature of 700 o C and thermal power of 10 MW. The first criticality benchmark problem of HTR-10 in this paper includes the loading number calculation of nuclear fuel in the form of UO 2 ball with U-235 enrichment of 17% for the first criticality under the helium atmosphere and core temperature of 20 o C, and the effective multiplication factor (k eff ) calculation of full core (5 m 3 ) under the helium atmosphere and various core temperatures. The group constants of fuel mixture, moderator and reflector materials were generated with WlMS/D4 using spherical model and 4 neutron energy group. The critical core height of 150.1 cm obtained from CITATION in 2-D R-Z reactor geometry exists in the calculation range of INET China, JAERI Japan and BATAN Indonesia, and OKBM Russia. The k eff calculation result of full core at various temperatures shows that the HTR-10 has negative temperature coefficient of reactivity. (author)

HTR-10GT AMBs displacement sensor design

International Nuclear Information System (INIS)

Shi Zhengang; Zha Meisheng; Zhao Lei; Sun Zhuo

2005-01-01

The 10 MW high temperature gas-cooled test module reactor (HTR-10GT) with the core made of spherical fuel elements was designed and constructed by the Institute of Nuclear and New Energy Technology of Tsinghua University in China. In the HTR-10GT, turbo-compressor and generator rotors are connected by a flexible coupling. The rotors, restricted by actual instruments and working environment, must be supported without any contact and lubrication. Active magnetic bearing (AMB), known as its advantages over the conventional bearings., such as contact-free, no-lubricating and active damping vibration, is the best way to suspend and stabilize the position of rotors of HTR-10GT. Each rotor is suspended by two radial and one axial AMBs. The radial AMB's radial gap is 0.15 mm considering the gap of 0.4 mm between the compressor stator and blades in order to protect the compressor. The control system controls the rotor position to meet the required gaps between rotor and stator through windings current. All the position information concerning radial and axial AMB is generated by sensors for measuring the displacement of the levitated body. Some typical sensors, i.e. eddy current displacement sensor, capacitive displacement sensor, can provide position information, but, quite often, unsatisfactory anti-jamming, which is a key issue for AMB systems near generator and other electric devices in HTR-10GT. Therefore, a kind of new type sensor is designed to measure the radial and axial displacements and the vibration of the rotors. This paper focuses on the design characteristics of the HTR-10GT AMBs displacement sensors and introduction of the related experiments to demonstrate its performance. (authors)

Reactor physics calculations on the Dutch small HTR concept

International Nuclear Information System (INIS)

Kuijper, J.C.; Haas, J.B.M. de; Klippel, H.T.; Hogenbirk, A.; Oppe, J.; Sciolla, C.M.; Stad, R.C.L. van der; Zhang, B.C.

1997-06-01

As part of the activities within the framework of the development of INCOGEN, a 'Dutch' conceptual design of a smaller HTR, the ECN reactor physics code system has been extended with the capability to perform combined neutronics and thermal hydraulics steady-state, burnup and transient core calculations on pebble-bed type HTRs, by joining the general purpose reactor code PANTHER and the HTR thermal hydraulics code THERMIX/DIREKT in the PANTHERMIX code combination. The validation of the ECN code system for HTR applications is still in progress, but some promising first calculation results on unit cell and whole core geometries are presented, which indicate that the extended ECN code system is quite suitable for performing the pebble-bed HTR core calculations, required in the INCOGEN core design and optimization process. (orig.)

Reactor physics calculations on the Dutch small HTR concept

International Nuclear Information System (INIS)

Kuijper, J.C.; Hass, J.B.M. De; Klippel, H.Th.; Hogenbirk, A.; Oppe, J.; Sciolla, C.; Stad, R.C.L. Van Der; Zhang, B.C.

1997-01-01

As part of the activities within the framework of the development of INCOGEN, a ''Dutch'' conceptual design of a small HTR, the ECN reactor physics code system has been extended with the capability to perform combined neutronics and thermal hydraulics steady-state, burnup and transient core calculations on pebble-bed type HTRS, by joining the general purpose reactor code PANTHER and the HTR thermal hydraulics code THERMIX/DIREKT in the PANTHERMIX code combination. The validation of the ECN code system for HTR applications is still in progress, but some promising first calculation results on unit cell and whole core geometries are presented, which indicate that the extended ECN code system is quite suitable for performing the pebble-bed HTR core calculations, required in the INCOGEN core design and optimization process. (author)

Simulation of Thermal-hydraulic Process in Reactor of HTR-PM

International Nuclear Information System (INIS)

Zhou Kefeng; Zhou Yangping; Sui Zhe; Ma Yuanle

2014-01-01

This paper provides the physical process in the reactor of High Temperature Gas-cooled Reactor Pebble-bed Module (HTR-PM) and introduces the standard operation conditions. The FORTRAN code developed for the thermal hydraulic module of Full-Scale Simulator (FSS) of HTR-PM is used to simulate two typical operation transients including cold startup process and cold shutdown process. And the results were compared to the safety analysis code, namely TINTE. The good agreement indicates that the code is applicable for simulating the thermal-hydraulic process in reactor of HTR-PM. And for long time transient process, the code shows good stability and convergence. (author)

Characteristic analysis of rotor dynamics and experiments of active magnetic bearing for HTR-10GT

International Nuclear Information System (INIS)

Yang Guojun; Xu Yang; Shi Zhengang; Gu Huidong

2005-01-01

A 10 MW high-temperature gas-cooled reactor (HTR-10) was constructed by the Institute of Nuclear and New Energy Technology (INET) at Tsinghua University of China. The helium turbine and generator system of 10 MW high temperature gas-cooled reactor (HTR-10GT) is the second phase for the HTR-10 project. It is to set up a direct helium cycle to replace the current steam cycle. The active magnetic bearing (AMB) instead of ordinary mechanical bearing was chosen to support the rotor in the HTR-10GT. This rotor is vertically mounted to hold the turbine machine, compressors and the power generator together. The rotor's length is 7 m, its weight is about 1500 kg and the rotating speed is 15000 r/min. The structure of the rotor is so complicated that dynamic analysis of the rotor becomes difficult. One of the challenging problems is to exceed natural frequencies with enough stability and safety during reactor start up, power change and shutdown. The dynamic analysis of the rotor is the base for the design of control system. It is important for the rotor to exceed critical speeds. Some kinds of software and methods, such as MSC.Marc, Ansys, and the Transfer Matrix Method, are compared to fully analyze rotor dynamics characteristic in this paper. The modal analysis has been done for the HTR-10GT rotor. MSC.Marc was finally selected to analyze the vibration mode and the natural frequency of the rotor. The effects of AMB stiffness on the critical speeds of the rotor were studied. The design characteristics of the AMB control system for the HTR-10GT were studied and the related experiment to exceed natural frequencies was introduced. The experimental results demonstrate the system functions and validate the control scheme, which will be used in the HTR-10GT project. (authors)

Symbiosis of near breeder HTR's with hybrid fusion reactors

International Nuclear Information System (INIS)

Seifritz, W.

1978-07-01

In this contribution to INFCE a symbiotic fusion/fission reactor system, consisting of a hybrid beam-driven micro-explosion fusion reactor (HMER) and associated high-temperature gas-cooled reactors (HTR) with a coupled fuel cycle, is proposed. This system is similar to the well known Fast Breeder/Near Breeder HTR symbiosis except that the fast fission breeder - running on the U/Pu-cycle in the core and the axial blankets and breeding the surplus fissile material as U-233 in its radial thorium metal or thorium oxide blankets - is replaced by a hybrid micro-explosion DT fusion reactor

Criticality calculations of the HTR-10 pebble-bed reactor with SCALE6/CSAS6 and MCNP5

International Nuclear Information System (INIS)

Wang, Meng-Jen; Sheu, Rong-Jiun; Peir, Jinn-Jer; Liang, Jenq-Horng

2014-01-01

Highlights: • Comparisons of the HTR-10 criticality calculations with SCALE6/CSAS6 and MCNP5 were performed. • The DOUBLEHET unit-cell treatment provides the best k eff estimation among PBR criticality calculations using SCALE6. • The continuous-energy SCALE6 calculations present a non-negligible discrepancy with MCNP5 in three PBR cases. - Abstract: HTR-10 is a 10 MWt prototype pebble-bed reactor (PBR) that presents a doubly heterogeneous geometry for neutronics calculations. An appropriate unit-cell treatment for the associated fuel elements is vital for creating problem-dependent multigroup cross sections. Considering four unit-cell options for resonance self-shielding correction in SCALE6, a series of HTR-10 core models were established using the CSAS6 sequence to systematically investigate how they affected the computational accuracy and efficiency of PBR criticality calculations. Three core configurations, which ranged from simplified infinite lattices to a detailed geometry, were examined. Based on the same ENDF/B-VII.0 cross-section library, multigroup results were evaluated by comparing with continuous-energy SCALE6/CSAS6 and MCNP5 calculations. The comparison indicated that the INFHOMMEDIUM results overestimated the effective multiplication factor (k eff ) by about 2800 pcm, whereas the LATTICECELL and MULTIREGION treatments overestimated k eff values with similar biases at approximately 470–680 pcm. The DOUBLEHET results attained further improvement, reducing the k eff overestimation to approximately 280 pcm. The comparison yielded two unexpected problems from using SCALE6/CSAS6 in HTR-10 criticality calculations. In particular, the continuous-energy CSAS6 calculations in this study present a non-negligible discrepancy with MCNP5, potentially causing a k eff value overestimate of approximately 680 pcm. Notably, using a cell-weighted mixture instead of an explicit model of individual TRISO particles in the pebble fuel zone does not shorten the

Development and Reliability Analysis of HTR-PM Reactor Protection System

International Nuclear Information System (INIS)

Li Duo; Guo Chao; Xiong Huasheng

2014-01-01

High Temperature Gas-Cooled Reactor-Pebble bed Module (HTR-PM) digital Reactor Protection System (RPS) is a dedicated system, which is designed and developed according to HTR-PM NPP protection specifications. To decrease the probability of accident trips and increase the system reliability, HTR-PM RPS has such features as a framework of four redundant channels, two diverse sub-systems in each channel, and two level two-out-of-four logic voters. Reliability analysis of HTR-PM RPS is based on fault tree model. A fault tree is built based on HTR-PM RPS Failure Modes and Effects Analysis (FMEA), and special analysis is focused on the sub-tree of redundant channel ''2-out-of-4'' logic and the fault tree under one channel is bypassed. The qualitative analysis of fault tree, such as RPS weakness according to minimal cut sets, is summarized in the paper. (author)

Source Term Analysis of the Irradiated Graphite in the Core of HTR-10

Directory of Open Access Journals (Sweden)

Xuegang Liu

2017-01-01

Full Text Available The high temperature gas-cooled reactor (HTGR has potential utilization due to its featured characteristics such as inherent safety and wide diversity of utilization. One distinct difference between HTGR and traditional pressurized water reactor (PWR is the large inventory of graphite in the core acting as reflector, moderator, or structure materials. Some radionuclides will be generated in graphite during the period of irradiation, which play significant roles in reactor safety, environmental release, waste disposal, and so forth. Based on the actual operation of the 10 MW pebble bed high temperature gas-cooled reactor (HTR-10 in Tsinghua University, China, an experimental study on source term analysis of the irradiated graphite has been done. An irradiated graphite sphere was randomly collected from the core of HTR-10 as sample in this study. This paper focuses on the analytical procedure and the establishment of the analytical methodology, including the sample collection, graphite sample preparation, and analytical parameters. The results reveal that the Co-60, Cs-137, Eu-152, and Eu-154 are the major γ contributors, while H-3 and C-14 are the dominating β emitting nuclides in postirradiation graphite material of HTR-10. The distribution profiles of the above four nuclides are also presented.

Design of the steam reformer for the HTR-10 high temperature process heat application

International Nuclear Information System (INIS)

Ju Huaiming; Xu Yuanhui; Jia Haijun

2000-01-01

The 10 MW High Temperature Reactor Test Module (HTR-10) is being constructed now and planned to be operational in 2000. One of the objectives is to develop the high temperature process heat application. The methane steam reformer is one of the key-facilities for the nuclear process heat application system. The paper describes the conceptual design of the HTR-10 Steam Reformer with He heating, and the design optimization computer code. It can be used to perform sensitivity analysis for parameters, and to improve the design. Principal parameters and construction features of the HTR-10 reformer heated by He are introduced. (author)

Energy analysis of control rod drive mechanism in HTR-10

International Nuclear Information System (INIS)

Bo Hanliang; Wu Yuanqiang

2000-01-01

This paper presents a theoretical model for the control rod drive mechanism for the 10 MW High Temperature Gas Cooled Reactor (HTR-10) and analyzes accidents which may occur in the drive mechanism, for example, chain break, coupling damage and other damage scenarios. The results show that the matching problem between buffer capability and coupling strength is the main reason for coupling damage; increased temperatures would reduce eddy damping and cause a mismatch between buffer capability and coupling strength; and the displacement of the buffer spring will affect the coupling force. The results provide a theoretical basis for the design of the control rod drive mechanism for HTR-10

The HTR-10 test reactor project and potential use of HTGR for non-electric application in China

International Nuclear Information System (INIS)

Sun Yuliang; Zhong Daxin; Xu Yuanhui; Wu Zhongxin

1997-01-01

Coal is the dominant source of energy in China. This use of coal results in two significant problems for China; it is a major burden on the train, road and waterway transportation infrastructures and it is a significant source of environmental pollution. In order to ease the problems caused by the burning of coal and to help reduce the energy supply shortage in China, national policy has directed the development of nuclear power. This includes the erection of nuclear power plants with water cooled reactors and the development of advanced nuclear reactor types, specifically, the high temperature gas cooled reactor (HTGR). The HTGR was chosen for its favorable safety features and its ability to provide high reactor outlet coolant temperatures for efficient power generation and high quality process heat for industrial applications. As the initial modular HTGR development activity within the Chinese High Technology Programme, a 10MW helium cooled test reactor is currently under construction on the site of the Institute of Nuclear Energy Technology northwest of Beijing. This plant features a pebble-bed helium cooled reactor with initial criticality anticipated in 1999. There will be two phases of high temperature heat utilization from the HTR-10. The first phase will utilize a reactor outlet temperature of 700 deg. C with a steam generator providing steam for a steam turbine cycle which works on an electrical/heat co-generation basis. The second phase is planned for a core outlet temperature of 900 deg. C to investigate a steam cycle/gas turbine combined cycle system with the gas turbine and the steam cycle being independently parallel in the secondary side of the plant. This paper provides a review of the technical design, licensing, safety and construction schedule for the HTR-10. It also addresses the potential uses of the HTGR for non-electric applications in China including process steam for the petrochemical industry, heavy oil recovery, coal conversion and

Analysis of aging mechanism and management for HTR-PM reactor pressure vessel

International Nuclear Information System (INIS)

Sun Yunxue; Shao Jin

2015-01-01

Reactor pressure vessel is an important part of the reactor pressure boundary, its important degree ranks high in ageing management and life assessment of nuclear power plant. Carrying out systematic aging management to ensure reactor pressure vessel keeping enough safety margins and executing design functions is one of the key factors to guarantee security and stability operation for nuclear power plant during the whole lifetime and prolong life. This paper briefly introduces the structure and aging mechanism of reactor pressure vessel in pressurized water reactor nuclear power plant, and introduces the design principle and structure characteristics of HTR-PM. At the same time, this paper carries out preliminary analysis and exploration. and discusses aging management of HTR-PM reactor pressure vessel. Finally, the advice of carring out aging management for HTR-PM reactor pressure vessel is proposed. (authors)

Monte carlo calculation of the neutron effective dose rate at the outer surface of the biological shield of HTR-10 reactor

International Nuclear Information System (INIS)

Remetti, Romolo; Andreoli, Giulio; Keshishian, Silvina

2012-01-01

Highlights: ► We deal with HTR-10, that is a helium-cooled graphite-moderated pebble bed reactor. ► We carried out Monte Carlo simulation of the core by MCNP5. ► Extensive use of MCNP5 variance reduction methods has been done. ► We calculated the trend of neutron flux within the biological shield. ► We calculated neutron effective dose at the outer surface of biological shield. - Abstract: Research on experimental reactors, such as HTR-10, provide useful data about potentialities of very high temperature gas-cooled reactors (VHTR). The latter is today rated as one of the six nuclear reactor types involved in the Generation-IV International Forum (GIF) Initiative. In this study, the MCNP5 code has been employed to evaluate the neutron radiation trend vs. the biological shield's thickness and to calculate the neutron effective dose rate at the outer surface. The reactor's geometry has been completely modeled by means of lattices and universes provided by MCNP, even though some approximations were required. Monte Carlo calculations have been performed by means of a simple PC and, as a consequence, in order to obtain acceptable run times, it was made an extensive recourse to variance reduction methods.

Viability of HTR-10 as a Primary Driver of an Energy Complex for Remote Settlement

International Nuclear Information System (INIS)

Choong, Philip T.

2014-01-01

HTR-10, a proven 10 MWt prototype pebble bed reactor, is capable of generating 4 MWe to the power grid. However; with evolutional power upgrades, its output performance can be substantially enhanced to drive an energy complex to co-generate electricity, hydrogen, desalinated water and process heat for a remote island or settlement of several thousand people. Unlike the much publicized SMR power concepts in the literature, HTR-10 is the only full-blown stand-alone power system that has been demonstrated to be inherently safe and capable of high temperature output. Furthermore, this particular HTR family of reactors is proliferation-resistant and possesses many desirable market-competitive advantages such as high thermal efficiency, low thermal pollution, zero carbon footprints and minimal exclusion zones. An innovative classroom project course is structured to stimulate science and engineering students to explore novel use of HTR-10 as a high temperature heat source to be the core of an intelligent zero emission energy (Smart-ZEE) module capable of providing all energy needs of a remote community or island. (author)

Calculation of the Fission Product Release for the HTR-10 based on its Operation History

International Nuclear Information System (INIS)

Xhonneux, A.; Druska, C.; Struth, S.; Allelein, H.-J.

2014-01-01

Since the first criticality of the HTR-10 test reactor in 2000, a rather complex operation history was performed. As the HTR-10 is the only pebble bed reactor in operation today delivering experimental data for HTR simulation codes, an attempt was made to simulate the whole reactor operation up to the presence. Special emphasis was put on the fission product release behaviour as it is an important safety aspect of such a reactor. The operation history has to be simulated with respect to the neutronics, fluid mechanics and depletion to get a detailed knowledge about the time-dependent nuclide inventory. In this paper we report about such a simulation with VSOP 99/11 and our new fission product release code STACY. While STACY (Source Term Analysis Code System) so far was able to calculate the fission product release rates in case of an equilibrium core and during transients, it now can also be applied to running-in-phases. This coupling demonstrates a first step towards an HCP Prototype. Based on the published power histogram of the HTR-10 and additional information about the fuel loading and shuffling, a coupled neutronics, fluid dynamics and depletion calculation was performed. Special emphasis was put on the complex fuel-shuffling scheme within both VSOP and STACY. The simulations have shown that the HTR-10 up to now generated about 2580 MWd while reshuffling the core about 2.3 times. Within this paper, STACY results for the equilibrium core will be compared with FRESCO-II results being published by INET. Compared to these release rates, which are based on a few user defined life histories, in this new approach the fission product release rates of Ag-110m, Cs-137, Sr-90 and I-131 have been simulated for about 4000 tracer pebbles with STACY. For the calculation of the HTR-10 operation history time-dependent release rates are being presented as well. (author)

Prediction calculation of HTR-10 fuel loading for the first criticality

International Nuclear Information System (INIS)

Jing Xingqing; Yang Yongwei; Gu Yuxiang; Shan Wenzhi

2001-01-01

The 10 MW high temperature gas cooled reactor (HTR-10) was built at Institute of Nuclear Energy Technology, Tsinghua University, and the first criticality was attained in Dec. 2000. The high temperature gas cooled reactor physics simulation code VSOP was used for the prediction of the fuel loading for HTR-10 first criticality. The number of fuel element and graphite element was predicted to provide reference for the first criticality experiment. The prediction calculations toke into account the factors including the double heterogeneity of the fuel element, buckling feedback for the spectrum calculation, the effect of the mixture of the graphite and the fuel element, and the correction of the diffusion coefficients near the upper cavity based on the transport theory. The effects of impurities in the fuel and the graphite element in the core and those in the reflector graphite on the reactivity of the reactor were considered in detail. The first criticality experiment showed that the predicted values and the experiment results were in good agreement with little relative error less than 1%, which means the prediction was successful

The safety characteristics of the HTR 500 reactor plant

International Nuclear Information System (INIS)

Wachholz, W.

1987-01-01

The HTR is a reactor having a passive safety. It is equipped with the usual active engineered safety systems in simplified form. Due to its inherent safety characteristics and the burst-safe prestressed concrete reactor vessel activity containment is ensured even without the effect of active safety systems. Even in the event of extremely hypothetical accidents the effect on the environment is low enough so that evacuation or relocation of the population is not required. Therefore large-scale damage of agricultural land and industrially used areas is safely ruled out. Thus the site selection for this type of reactor is not restricted i.e. an HTR can be constructed near industrial and urban center. (author)

Thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

International Nuclear Information System (INIS)

Silva, Alexandro S.; Dominguez, Dany S.; Mazaira, Leorlen Y. Rojas; Hernandez, Carlos R.G.; Lira, Carlos Alberto Brayner de Oliveira

2015-01-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal–hydraulic characteristics. In this article, it was performed the thermal–hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a column of FCC (Face Centered Cubic) cells, with 41 layers and 82 pebbles. The input data used were taken from the thermohydraulic IAEA Benchmark (TECDOC-1694). The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Actual characteristics study on HTR-10GT coupling with direct gas turbine cycle

International Nuclear Information System (INIS)

Peng Xuechuang; Zhu Shutang; Wang Jie

2005-01-01

HTR-10GT is a testing project coupling the reactor HTR-10 with direct gas turbine cycle. Its thermal cycle can be taken as a closed, recuperated and inter-cooled Brayton cycle. The present study is focused on the thermal cycle performance of HTR-10GT under practical conditions of leakage, pressure losses, etc.. Through thermodynamic analysis, the expression of cycle efficiency for actual thermal cycle is derived. By establishing a physical model with friction loss and leakage, a set of governing equation are constructed based on some reasonable assumptions. The results of actual cycle efficiency have been calculated for different leakage amount at different locations while the effects of leakage under different power level have also been calculated and analyzed. (authors)

High Temperature Reactor (HTR) Deep Burn Core and Fuel Analysis: Design Selection for the Prismatic Block Reactor

Energy Technology Data Exchange (ETDEWEB)

Francesco Venneri; Chang-Keun Jo; Jae-Man Noh; Yonghee Kim; Claudio Filippone; Jonghwa Chang; Chris Hamilton; Young-Min Kim; Ji-Su Jun; Moon-Sung Cho; Hong-Sik Lim; MIchael A. Pope; Abderrafi M. Ougouag; Vincent Descotes; Brian Boer

2010-09-01

The Deep Burn (DB) Project is a U.S. Department of Energy sponsored feasibility study of Transuranic Management using high burnup fuel in the high temperature helium cooled reactor (HTR). The DB Project consists of seven tasks: project management, core and fuel analysis, spent fuel management, fuel cycle integration, TRU fuel modeling, TRU fuel qualification, and HTR fuel recycle. In the Phase II of the Project, we conducted nuclear analysis of TRU destruction/utilization in the HTR prismatic block design (Task 2.1), deep burn fuel/TRISO microanalysis (Task 2.3), and synergy with fast reactors (Task 4.2). The Task 2.1 covers the core physics design, thermo-hydraulic CFD analysis, and the thermofluid and safety analysis (low pressure conduction cooling, LPCC) of the HTR prismatic block design. The Task 2.3 covers the analysis of the structural behavior of TRISO fuel containing TRU at very high burnup level, i.e. exceeding 50% of FIMA. The Task 4.2 includes the self-cleaning HTR based on recycle of HTR-generated TRU in the same HTR. Chapter IV contains the design and analysis results of the 600MWth DB-HTR core physics with the cycle length, the average discharged burnup, heavy metal and plutonium consumptions, radial and axial power distributions, temperature reactivity coefficients. Also, it contains the analysis results of the 450MWth DB-HTR core physics and the analysis of the decay heat of a TRU loaded DB-HTR core. The evaluation of the hot spot fuel temperature of the fuel block in the DB-HTR (Deep-Burn High Temperature Reactor) core under full operating power conditions are described in Chapter V. The investigated designs are the 600MWth and 460MWth DB-HTRs. In Chapter VI, the thermo-fluid and safety of the 600MWth DB-HTRs has been analyzed to investigate a thermal-fluid design performance at the steady state and a passive safety performance during an LPCC event. Chapter VII describes the analysis results of the TRISO fuel microanalysis of the 600MWth and 450

HTR-TN a European network for the development of HTR technology

International Nuclear Information System (INIS)

Von Lensa, W.

2001-01-01

A network called High-temperature reactor technology network (HTR-TN) has been created at a European level to coordinate works and knowledge on the subject with a long-term perspective and to serve as a channel for international collaboration. An analysis confirmed that the obvious economic penalty of HTR due to its low density power could be compensated by the combination of recent advances that may completely change the positioning of HTR on the energy market: -) the modular concept allowed to get a reactor free from core melt risk without intervention of any active safety system, implying a drastic simplification of the design of the reactor and the safety systems as well as a standardisation and potential for shop fabrication in series; -) the development of gas turbines, the efficiency of which increased, in 10 years, from 35% till 50% and more, enabling to consider suppression of the secondary system; -) the ultra high burn-up potential of HTR fuel and the possibility for direct disposal of spent HTR fuel elements that may reduce cost of the fuel cycle and contribute to the reduction of civil and military plutonium stockpiles. (A.C.)

Simulation and study on reactivity disturbs dynamic character of HTR-10 nuclear power system

International Nuclear Information System (INIS)

Huang Xiaojin; Feng Yuankun

2002-01-01

In order to not only know 10 MW High Temperature Gas Cooled Reactor (HTR-10) nuclear power system's dynamic character more deeply but also to satisfy requirements of control system's design and analysis, the dynamic model of HTR-10 nuclear power system is established on the basis of dynamic model of HTR-10 nuclear system, which supplies turbine and generate electricity system model. Using this model, system's main variables' dynamic processes are simulated when control rod takes step reactivity disturb. The concussive progresses which is caused by reactivity disturb are analyzed. The results indicate that fuel temperature changing more slowly than nuclear power makes reactivity negative feedback not to restrain power changing, and then power concussive progress comes to being

Experiment study on thermal mixing performance of HTR-PM reactor outlet

Energy Technology Data Exchange (ETDEWEB)

Zhou, Yangping, E-mail: zhouyp@mail.tsinghua.edu.cn [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, the Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Tsinghua University, Beijing 100084 (China); Hao, Pengfei [School of Aerospace, Tsinghua University, Beijing 100084 (China); Li, Fu; Shi, Lei [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, the Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Tsinghua University, Beijing 100084 (China); He, Feng [School of Aerospace, Tsinghua University, Beijing 100084 (China); Dong, Yujie; Zhang, Zuoyi [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, the Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Tsinghua University, Beijing 100084 (China)

2016-09-15

A model experiment is proposed to investigate the thermal mixing performance of HTR-PM reactor outlet. The design of the test facility is introduced, which is set at a scale of 1:2.5 comparing with the design of thermal mixing structure at HTR-PM reactor outlet. The test facility using air as its flow media includes inlet pipe system, electric heaters, main mixing structure, hot gas duct, exhaust pipe system and I&C system. Experiments are conducted on the test facility and the values of thermal-fluid parameters are collected and analyzed, which include the temperature, pressure and velocity of the flow as well as the temperature of the tube wall. The analysis results show the mixing efficiency of the test facility is higher than that required by the steam generator of HTR-PM, which indicates that the thermal mixing structure of HTR-PM fulfills its design requirement.

Potential of thorium use in the HTR reactor

International Nuclear Information System (INIS)

Engelmann, P.; Hansen, U.; Kolb, G.; Leushacke, D.; Teuchert, E.; Werner, H.

1979-08-01

In this investigation, several types of reactors and fuel circulations are dealt with as they refer to the region of the Federal Republic of Germany and are compared with each other as to their need for uranium and their costs until 2100. This includes also an investigation covering the effects of a postponed application of uranium-saving reactors, a delayed reprocessing and two variants of the nuclear energy's contribution to electricity generation. After today's light water reactor (LWR) of the pressure water reactor type (DWR) and the sodium-cooled fast breeder (SBR) which is being developed, the technically rather developed helium-cooled high temperature reactor (HTR) is dealt with as another system. The high temperature reactor is, because of its high coolant temperatures, not only suitable as a nuclear power plant, but can also be used to substitute fossile energy sources on the heat market and is being developed in Germany also for use as process heat reactor for nuclear coal gasification. Here the application of nuclear energy is only considered with regard to the region of power generation. Besides the case of the LWR and HTR-operation without reprocessing and fuel recycling for all reactor systems, the calculations also take into consideration the case of the closed fuel recycling. While LWR and SBR are based on the uranium-plutonium-fuel recycling, the thorium-uranium fuel circulation is considered for the HTR with globular fuel elements. As investigations made until today are generally restricted to the system LWR/SBR and the uranium-plutonium circulation, a main concern of the investigations presented here is to show the potential of the Thorium-utilization in high-temperature reactors and to determine how this system can also be applied during the time period concerned to set up a nuclear energy strategy which is safe and profitable as far as the uranium supply is concerned. (orig./UA) 891 UA/orig.- 892 HIS [de

Reactor physics calculations on HTR type configurations

Energy Technology Data Exchange (ETDEWEB)

Klippel, H.T.; Hogenbirk, A.; Stad, R.C.L. van der; Janssen, A.J.; Kuijper, J.C.; Levin, P.

1995-04-01

In this paper a short description of the ECN nuclear analysis code system is given with respect to application in HTR reactor physics calculations. First results of calculations performed on the PROTEUS benchmark are shown. Also first results of a HTGR benchmark are given. (orig.).

Reactor physics calculations on HTR type configurations

International Nuclear Information System (INIS)

Klippel, H.T.; Hogenbirk, A.; Stad, R.C.L. van der; Janssen, A.J.; Kuijper, J.C.; Levin, P.

1995-04-01

In this paper a short description of the ECN nuclear analysis code system is given with respect to application in HTR reactor physics calculations. First results of calculations performed on the PROTEUS benchmark are shown. Also first results of a HTGR benchmark are given. (orig.)

Progress of the HTR-10 project

International Nuclear Information System (INIS)

Zhong, D.; Xu, Y.

1996-01-01

This paper briefly introduces the main technical features and the design specifications of the HTR-10. Present status and main progress of the license applications, the design and manufacture of the main components and the engineering experiments as well as the construction of the HTR-10 are summarized. (author). 3 tabs

Burn-up measurement in the HTR-module-reactor

International Nuclear Information System (INIS)

Gerhards, E.

1993-05-01

The burn-up status of spherical HTR-fuel elements is determined by a γ-spectrometric analysis of Cs-137 activity. The γ-spectrum recorded by a semiconductor detector up to now is analyzed by complex mathematical and time-consuming methods. For the operation of the HTR-Module-Reactor, however, a fast evaluation of the burn-up status is necessary. It is shown that this can be ensured by a comparison between the measured spectra and simulation results. Using the computer-program HTROGEN and the program system SPECCALC especially developed for this problem the γ-spectra are evaluated as a function of the burn-up status. The method is applied to results available from the operation of the AVR-reactor. The burn-up status determined with different methods corresponds very well within the limits of accuracy. (orig.)

Modelling of HTR (High Temperature Reactor Pebble-Bed 10 MW to Determine Criticality as A Variations of Enrichment and Radius of the Fuel (Kernel With the Monte Carlo Code MCNP4C

Directory of Open Access Journals (Sweden)

Hammam Oktajianto

2014-12-01

Full Text Available Gas-cooled nuclear reactor is a Generation IV reactor which has been receiving significant attention due to many desired characteristics such as inherent safety, modularity, relatively low cost, short construction period, and easy financing. High temperature reactor (HTR pebble-bed as one of type of gas-cooled reactor concept is getting attention. In HTR pebble-bed design, radius and enrichment of the fuel kernel are the key parameter that can be chosen freely to determine the desired value of criticality. This paper models HTR pebble-bed 10 MW and determines an effective of enrichment and radius of the fuel (Kernel to get criticality value of reactor. The TRISO particle coated fuel particle which was modelled explicitly and distributed in the fuelled region of the fuel pebbles using a Simple-Cubic (SC lattice. The pebble-bed balls and moderator balls distributed in the core zone using a Body-Centred Cubic lattice with assumption of a fresh fuel by the fuel enrichment was 7-17% at 1% range and the size of the fuel radius was 175-300 µm at 25 µm ranges. The geometrical model of the full reactor is obtained by using lattice and universe facilities provided by MCNP4C. The details of model are discussed with necessary simplifications. Criticality calculations were conducted by Monte Carlo transport code MCNP4C and continuous energy nuclear data library ENDF/B-VI. From calculation results can be concluded that an effective of enrichment and radius of fuel (Kernel to achieve a critical condition was the enrichment of 15-17% at a radius of 200 µm, the enrichment of 13-17% at a radius of 225 µm, the enrichments of 12-15% at radius of 250 µm, the enrichments of 11-14% at a radius of 275 µm and the enrichment of 10-13% at a radius of 300 µm, so that the effective of enrichments and radii of fuel (Kernel can be considered in the HTR 10 MW. Keywords—MCNP4C, HTR, enrichment, radius, criticality 

The future of HTR development and market chances

International Nuclear Information System (INIS)

Baust, E.; Weisbrodt, I.

1989-01-01

In more than thirty years of development, the pebble bed high-temperature reactor has been brought to the threshold of commercial maturity. On the basis of the experience accumulated with the 15 MW AVR reactor and the THTR-300, unit sizes tailored to demand (HTR-500, modular HTR, GHR-10) will be developed for the electricity and heat markets of the future. The high-temperature reactor is a meaningful supplement to the proven line of light-water reactors and is particularly suitable for being exported to developing countries and industrial threshold countries because of its special technical and inherent safeguards properties. There is broad worldwide interest in the HTR, as is evidenced by several existing agreements on cooperation. It is for this reason that market chances are believed to exist for the HTR after the expected revival of the nuclear power market. ABB and Siemens therefore have decided to develop and market the HTR jointly in the future as a matter of long term strategy by working through a joint subsidiary, HTR-GmbH. (orig.) [de

Numerical analysis of magnetically suspended rotor in HTR-10 helium circulator being dropped into auxiliary bearings

International Nuclear Information System (INIS)

Zhao Jingxiong; Yang Guojun; Li Yue; Yu Suyuan

2012-01-01

Active magnetic bearings (AMB) have been selected to support the rotor of primary helium circulator in commercial 10 Mega-Walt High Temperature Gas-cooled Reactor (HTR-10). In an AMB system, the auxiliary bearings are necessary to protect the AMB components in case of losing power. This paper performs the impact simulation of Magnetically Suspended Rotor in HTR-10 Helium Circulator being dropped into the auxiliary bearings using the finite element program ABAQUS. The dynamic response and the strain field of auxiliary bearings are analyzed. The results achieved by the numerical analysis are in agreement with the experiment results. Therefore, the feasibility of the design of auxiliary bearing and the possibility of using the AMB system in the HTR are proved. (authors)

Stress analysis of HTR-10 steam generator heat exchanging tubes

International Nuclear Information System (INIS)

Dong Jianling; Zhang Xiaohang; Yin Dejian; Fu Jiyang

2001-01-01

Steam Generator (SG) heat exchanging tubes of 10 MW High Temperature Gas Cooled Reactor (HTR-10) are protective screens between the primary loop of helium with radioactivity and the secondary loop of feeding water and steam without radioactivity. Water and steam will enter into the primary loop when rupture of the heat exchanging tubes occurs, which lead to increase of the primary loop pressure and discharge of radioactive materials. Therefore it is important to guarantee the integrity of the tubes. The tube structure is spiral tube with small bending radius, which make it impossible to test with volumetric in-service detection. For such kind of spiral tube, using LBB concept to guarantee the integrity of the tubes is an important option. The author conducts stress analysis and calculation of HTR-10 SG heat exchanging tubes using the FEM code of piping stress analysis, PIPESTRESS. The maximum stress and the dangerous positions are obtained

Predictions of the Bypass Flows in the HTR-PM Reactor Core

International Nuclear Information System (INIS)

Sun Jun; Chen Zhipeng; Zheng Yanhua; Shi Lei; Li Fu

2014-01-01

In the HTR-PM reactor core, the basic structure materials are large amount of graphite reflectors and carbon bricks. Small gaps among those graphite and carbon bricks are widespread in the reactor core so that the cold helium flow may be bypassed and not completely heated. The bypass flows in relative lower temperature would change the flow and temperature distributions in the reactor core, therefore, the accurate prediction of bypass flows need to be carried out carefully to evaluate the influence to the reactor safety. Based on the characteristics of the bypass flow problem, hybrid method of the flow network and the CFD tools was employed to represent the connections and calculate flow distributions of all the main flow and bypass flow paths. In this paper, the hybrid method was described and applied to specific bypass flow problem in the HTR-PM. Various bypass flow paths in the HTR-PM were reviewed, figured out, and modeled by the flow network and the CFD methods, including the axial vertical gaps in the side reflectors, control rod channels, absorber sphere channels and radial gap flow through keys around the hot helium plenum. The bypass flow distributions and its flow rate ratio to the total flow rate in the primary loop were also calculated, discussed and evaluated. (author)

Numerical Simulation of Two-branch Hot Gas Mixing at Reactor Outlet of HTR-PM

International Nuclear Information System (INIS)

Hao Pengefei; Zhou Yangping; Li Fu; Shi Lei; He Heng

2014-01-01

A series of two-branch model experiment has been finished to investigate the thermal mixing efficiency of the HTR-PM reactor outlet. This paper introduces the numerical simulation on the design of thermal mixing structure of HTR-PM and the test facility with Fluent software. The profiles of temperature, pressure and velocity in the mixing structure design and the test facility are discussed by comparing with the model experiment results. The numerical simulation results of the test facility have good agreement to the experiment results. In addition, the thermal-fluid characters obtained by numerical simulation show the thermal mixing structure of HTR-PM has similarity with the test facility. Finally, it is concluded that the thermal mixing design at HTR-PM reactor outlet can fulfilled the requirements for high thermal mixing efficiency and appropriate pressure drop. (author)

Thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach; Simulacao termohidraulica do nucleo do reator nuclear HTR-10 com o uso da abordagem realistica CFD

Energy Technology Data Exchange (ETDEWEB)

Silva, Alexandro S.; Dominguez, Dany S., E-mail: alexandrossilva@gmail.com, E-mail: dsdominguez@gmail.com [Universidade Estadual de Santa Cruz (UESC), Ilheus, BA (Brazil); Mazaira, Leorlen Y. Rojas; Hernandez, Carlos R.G., E-mail: leored1984@gmail.com, E-mail: cgh@instec.cu [Instituto Superior de Tecnologias y Ciencias Aplicadas, La Habana (Cuba); Lira, Carlos Alberto Brayner de Oliveira, E-mail: cabol@ufpe.br [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

2015-07-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal–hydraulic characteristics. In this article, it was performed the thermal–hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a column of FCC (Face Centered Cubic) cells, with 41 layers and 82 pebbles. The input data used were taken from the thermohydraulic IAEA Benchmark (TECDOC-1694). The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Recent advances on thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

Energy Technology Data Exchange (ETDEWEB)

Silva, Alexandro S., E-mail: alexandrossilva@ifba.edu.br [Instituto Federal de Educacao, Ciencia e Tecnologia da Bahia (IFBA), Vitoria da Conquista, BA (Brazil); Mazaira, Leorlen Y.R., E-mail: leored1984@gmail.com, E-mail: cgh@instec.cu [Instituto Superior de Tecnologias y Ciencias Aplicadas (INSTEC), La Habana (Cuba); Dominguez, Dany S.; Hernandez, Carlos R.G., E-mail: alexandrossilva@gmail.com, E-mail: dsdominguez@gmail.com [Universidade Estadual de Santa Cruz (UESC), Ilheus, BA (Brazil). Programa de Pos-Graduacao em Modelagem Computacional; Lira, Carlos A.B.O., E-mail: cabol@ufpe.br [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

2015-07-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal-hydraulic characteristics. In this article, it was performed the thermal-hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a FCC (Face Centered Cubic) cell with the half height of the core, with 21 layers and 95 pebbles. The input data used were taken from the thermal-hydraulic IAEA Bechmark. The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Recent advances on thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

International Nuclear Information System (INIS)

Silva, Alexandro S.; Mazaira, Leorlen Y.R.; Dominguez, Dany S.; Hernandez, Carlos R.G.

2015-01-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal-hydraulic characteristics. In this article, it was performed the thermal-hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a FCC (Face Centered Cubic) cell with the half height of the core, with 21 layers and 95 pebbles. The input data used were taken from the thermal-hydraulic IAEA Bechmark. The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Gas reactor international cooperative program. HTR-synfuel application assessment

Energy Technology Data Exchange (ETDEWEB)

1979-09-01

This study assesses the technical, environmental and economic factors affecting the application of the High Temperature Gas-Cooled Thermal Reactor (HTR) to: synthetic fuel production; and displacement of fossil fuels in other industrial and chemical processes. Synthetic fuel application considered include coal gasification, direct coal liquefaction, oil shale processing, and the upgrading of syncrude to motor fuel. A wide range of other industrial heat applications was also considered, with emphasis on the use of the closed-loop thermochemical energy pipeline to supply heat to dispersed industrial users. In this application syngas (H/sub 2/ +CO/sub 2/) is produced at the central station HTR by steam reforming and the gas is piped to individual methanators where typically 1000/sup 0/F steam is generated at the industrial user sites. The products of methanation (CH/sub 4/ + H/sub 2/O) are piped back to the reformer at the central station HTR.

Gas reactor international cooperative program. HTR-synfuel application assessment

International Nuclear Information System (INIS)

1979-09-01

This study assesses the technical, environmental and economic factors affecting the application of the High Temperature Gas-Cooled Thermal Reactor (HTR) to: synthetic fuel production; and displacement of fossil fuels in other industrial and chemical processes. Synthetic fuel application considered include coal gasification, direct coal liquefaction, oil shale processing, and the upgrading of syncrude to motor fuel. A wide range of other industrial heat applications was also considered, with emphasis on the use of the closed-loop thermochemical energy pipeline to supply heat to dispersed industrial users. In this application syngas (H 2 +CO 2 ) is produced at the central station HTR by steam reforming and the gas is piped to individual methanators where typically 1000 0 F steam is generated at the industrial user sites. The products of methanation (CH 4 + H 2 O) are piped back to the reformer at the central station HTR

HTR-PROTEUS pebble bed experimental program cores 9 & 10: columnar hexagonal point-on-point packing with a 1:1 moderator-to-fuel pebble ratio

Energy Technology Data Exchange (ETDEWEB)

Bess, John D. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2014-03-01

PROTEUS is a zero-power research reactor based on a cylindrical graphite annulus with a central cylindrical cavity. The graphite annulus remains basically the same for all experimental programs, but the contents of the central cavity are changed according to the type of reactor being investigated. Through most of its service history, PROTEUS has represented light-water reactors, but from 1992 to 1996 PROTEUS was configured as a pebble-bed reactor (PBR) critical facility and designated as HTR-PROTEUS. The nomenclature was used to indicate that this series consisted of High Temperature Reactor experiments performed in the PROTEUS assembly. During this period, seventeen critical configurations were assembled and various reactor physics experiments were conducted. These experiments included measurements of criticality, differential and integral control rod and safety rod worths, kinetics, reaction rates, water ingress effects, and small sample reactivity effects (Ref. 3). HTR-PROTEUS was constructed, and the experimental program was conducted, for the purpose of providing experimental benchmark data for assessment of reactor physics computer codes. Considerable effort was devoted to benchmark calculations as a part of the HTR-PROTEUS program. References 1 and 2 provide detailed data for use in constructing models for codes to be assessed. Reference 3 is a comprehensive summary of the HTR-PROTEUS experiments and the associated benchmark program. This document draws freely from these references. Only Cores 9 and 10 are evaluated in this benchmark report due to similarities in their construction. The other core configurations of the HTR-PROTEUS program are evaluated in their respective reports as outlined in Section 1.0. Cores 9 and 10 were evaluated and determined to be acceptable benchmark experiments.

HTR-PROTEUS PEBBLE BED EXPERIMENTAL PROGRAM CORES 9 & 10: COLUMNAR HEXAGONAL POINT-ON-POINT PACKING WITH A 1:1 MODERATOR-TO-FUEL PEBBLE RATIO

Energy Technology Data Exchange (ETDEWEB)

John D. Bess

2013-03-01

PROTEUS is a zero-power research reactor based on a cylindrical graphite annulus with a central cylindrical cavity. The graphite annulus remains basically the same for all experimental programs, but the contents of the central cavity are changed according to the type of reactor being investigated. Through most of its service history, PROTEUS has represented light-water reactors, but from 1992 to 1996 PROTEUS was configured as a pebble-bed reactor (PBR) critical facility and designated as HTR-PROTEUS. The nomenclature was used to indicate that this series consisted of High Temperature Reactor experiments performed in the PROTEUS assembly. During this period, seventeen critical configurations were assembled and various reactor physics experiments were conducted. These experiments included measurements of criticality, differential and integral control rod and safety rod worths, kinetics, reaction rates, water ingress effects, and small sample reactivity effects (Ref. 3). HTR-PROTEUS was constructed, and the experimental program was conducted, for the purpose of providing experimental benchmark data for assessment of reactor physics computer codes. Considerable effort was devoted to benchmark calculations as a part of the HTR-PROTEUS program. References 1 and 2 provide detailed data for use in constructing models for codes to be assessed. Reference 3 is a comprehensive summary of the HTR-PROTEUS experiments and the associated benchmark program. This document draws freely from these references. Only Cores 9 and 10 are evaluated in this benchmark report due to similarities in their construction. The other core configurations of the HTR-PROTEUS program are evaluated in their respective reports as outlined in Section 1.0. Cores 9 and 10 were evaluated and determined to be acceptable benchmark experiments.

HTR-2002: Proceedings of the conference on high temperature reactors

International Nuclear Information System (INIS)

2002-01-01

High temperature reactors are considered as future inherently safe and efficient energy sources. The presentations covered all the relevant aspects of the existing HTGRs and/or helium cooled pebble bed reactors. They were sorted into 7 sessions: HTR Projects and Programmes; Fuel and Fuel Cycle; Physics and Neutronics; Thermohydraulic Calculation; Engineering, Design and Applications; Materials and Components; Safety and Licensing

High Temperature Reactor (HTR) Deep Burn Core and Fuel Analysis: Design Selection for the Prismatic Block Reactor With Results from FY-2011 Activities

Energy Technology Data Exchange (ETDEWEB)

Michael A. Pope

2011-10-01

The Deep Burn (DB) Project is a U.S. Department of Energy sponsored feasibility study of Transuranic Management using high burnup fuel in the high temperature helium cooled reactor (HTR). The DB Project consists of seven tasks: project management, core and fuel analysis, spent fuel management, fuel cycle integration, TRU fuel modeling, TRU fuel qualification, and HTR fuel recycle. In the Phase II of the Project, we conducted nuclear analysis of TRU destruction/utilization in the HTR prismatic block design (Task 2.1), deep burn fuel/TRISO microanalysis (Task 2.3), and synergy with fast reactors (Task 4.2). The Task 2.1 covers the core physics design, thermo-hydraulic CFD analysis, and the thermofluid and safety analysis (low pressure conduction cooling, LPCC) of the HTR prismatic block design. The Task 2.3 covers the analysis of the structural behavior of TRISO fuel containing TRU at very high burnup level, i.e. exceeding 50% of FIMA. The Task 4.2 includes the self-cleaning HTR based on recycle of HTR-generated TRU in the same HTR. Chapter IV contains the design and analysis results of the 600MWth DB-HTR core physics with the cycle length, the average discharged burnup, heavy metal and plutonium consumptions, radial and axial power distributions, temperature reactivity coefficients. Also, it contains the analysis results of the 450MWth DB-HTR core physics and the analysis of the decay heat of a TRU loaded DB-HTR core. The evaluation of the hot spot fuel temperature of the fuel block in the DB-HTR (Deep-Burn High Temperature Reactor) core under full operating power conditions are described in Chapter V. The investigated designs are the 600MWth and 460MWth DB-HTRs. In Chapter VI, the thermo-fluid and safety of the 600MWth DB-HTRs has been analyzed to investigate a thermal-fluid design performance at the steady state and a passive safety performance during an LPCC event. Chapter VII describes the analysis results of the TRISO fuel microanalysis of the 600MWth and 450

Random geometry capability in RMC code for explicit analysis of polytype particle/pebble and applications to HTR-10 benchmark

International Nuclear Information System (INIS)

Liu, Shichang; Li, Zeguang; Wang, Kan; Cheng, Quan; She, Ding

2018-01-01

Highlights: •A new random geometry was developed in RMC for mixed and polytype particle/pebble. •This capability was applied to the full core calculations of HTR-10 benchmark. •Reactivity, temperature coefficient and control rod worth of HTR-10 were compared. •This method can explicitly model different packing fraction of different pebbles. •Monte Carlo code with this method can simulate polytype particle/pebble type reactor. -- Abstract: With the increasing demands of high fidelity neutronics analysis and the development of computer technology, Monte Carlo method is becoming more and more attractive in accurate simulation of pebble bed High Temperature gas-cooled Reactor (HTR), owing to its advantages of the flexible geometry modeling and the use of continuous-energy nuclear cross sections. For the double-heterogeneous geometry of pebble bed, traditional Monte Carlo codes can treat it by explicit geometry description. However, packing methods such as Random Sequential Addition (RSA) can only produce a sphere packing up to 38% volume packing fraction, while Discrete Element Method (DEM) is troublesome and also time consuming. Moreover, traditional Monte Carlo codes are difficult and inconvenient to simulate the mixed and polytype particles or pebbles. A new random geometry method was developed in Monte Carlo code RMC to simulate the particle transport in polytype particle/pebble in double heterogeneous geometry systems. This method was verified by some test cases, and applied to the full core calculations of HTR-10 benchmark. The reactivity, temperature coefficient and control rod worth of HTR-10 were compared for full core and initial core in helium and air atmosphere respectively, and the results agree well with the benchmark results and experimental results. This work would provide an efficient tool for the innovative design of pebble bed, prism HTRs and molten salt reactors with polytype particles or pebbles using Monte Carlo method.

The HTR modular power reactor system. Qualification of fuel elements and materials

International Nuclear Information System (INIS)

Heidenreich, U.; Breitling, H.; Nieder, R.; Ohly, W.; Mittenkuehler, A.; Ragoss, H.; Seehafer, H.J.; Wirtz, K.; Serafin, N.

1989-01-01

For further development of the HTR modular power reactor system (HTR-M-KW), the project activities for 'Qualification of fuel elements and materials' reported here cover the work for specifying the qualifications to be met by metallic and ceramic materials, taking into account the design-based requirements and the engineered safety requirements. The fission product retention data determined for the HTR modular reactor fuel elements could be better confirmed by evaluation of the experiments, and have been verified by various calculation methods for different operating conditions. The qualification of components was verified by strength analyses including a benchmark calculation for specified normal operation and emergencies; the results show a convenient behaviour of the components and their materials. In addition, a fuel element burnup measuring system was designed that applies Cs-137 gamma spectroscopy; its feasibility was checked by appropriate analyses, and qualification work is in progress. The installation of a prototype measurement system is the task for project No. 03 IAT 211. (orig.) [de

MCNP qualification on the HTR critical configurations: HTTR, HTR10 and PROTEUS results

Energy Technology Data Exchange (ETDEWEB)

TRAKAS, Christos; STOVEN, Gilles [AREVA NP, Tour Areva, 92084 Paris La Defence Cedex (France)

2008-07-01

Recent critical experiments, including PROTEUS, HTTR and HTR-10 provide a reliable qualification base for HTR criticality predictions. The fuel tested in these experiments, be it hexagonal block or pebble type, is irradiated in a spectrum comparable to that of the HTR planned by AREVA NP. The neutron spectrum is comparable in all three cases; the mean C/M value for all critical cases is less than +350 pcm (JEF2.2), +250 pcm (JEFF3.1) and +60 pcm (ENDF BVI). The C/M obtained for the rods worth, the reaction rates and the isothermal coefficient are very satisfactory. (authors)

Development status of the HTGR in the world. Outline and construction status of the demonstration HTGR program (HTR-PM) of China

International Nuclear Information System (INIS)

Ohashi, Kazutaka; Okamoto, Futoshi; Mouri, Tomoaki; Saito, Masanao; Nishio, Hiroki; Ohashi, Junpei

2014-01-01

Based on successful construction and operation experiences of HTR-10 reactor with pebble bed fuel and helium coolant, HTR-PM (HTR Pebble-bed Modular) reactor program was under way with 200 MWe of twin reactors with the same core configuration as HTR-10 reactor, which, each with a single steam generator, would drive a single steam turbine. Core height was 11 meters, and main steam temperature would be at 566 C. Although HTR-PM reactor program was interrupted by effects of the Fukushima accident, first concrete basement construction was started in December 2012 with aiming at connecting the Grid in 2017. This article reviewed outline and construction status of HTR-PM reactor in China. (T. Tanaka)

HTR core physics analysis at NRG

International Nuclear Information System (INIS)

Kuijper, J.C.; Haas, J.B.M. de; Oppe, J.

2002-01-01

Since a number of years NRG is developing the HTR reactor physics code system PANTHERMIX. In PANTHERMIX the 3-D steady-state and transient core physics code PANTHER has been interfaced with the HTR thermal hydraulics code THERMIX to enable core follow and transient analyses on both pebble bed and block type HTR systems. Recently the capabilities of PANTHERMIX have been extended with the possibility to simulate the flow of pebbles through the core cavity and the (re)loading of pebbles on top of the core.The PANTHERMIX code system is being applied for the benchmark exercises for the Chinese HTR-10 and Japanese HTTR first criticality, calculating the critical loading, control rod worth and the isothermal temperature coefficients at zero power conditions. Also core physics calculations have been performed on an early version the South African PBMR design. The reactor physics properties of the reactor at equilibrium core loading have been studied as well as a selected run-in scenario, starting form fresh fuel. The recently developed reload option of PANTHERMIX was used extensively in these analyses. The examples shown demonstrate the capabilities of PANTHERMIX for performing steady-state and transient HTR core physics analyses. However, additional validation, especially for transient analyses, remains desirable. (author)

The Dragon project and high temperature reactor (HTR position)

International Nuclear Information System (INIS)

Shepherd, L.

1981-01-01

After introduction describing the initiation of HTR work at AERE and in West Germany and the USA, the subject is discussed in detail under the headings: the Dragon Reactor Experiment (design and objectives); fuel elements and graphite (description of cooperative research programmes; development of coated fuel particles); helium technology; other Dragon activities. (U.K.)

Proceedings of the Fifth Seminar of High Temperature Reactor: The Role and Challenge with HTR Opportunity in the Twenty-first Century

International Nuclear Information System (INIS)

As-Natio-Lasman; Zaki-Su'ud; Bambang-Sugiono

2000-11-01

The Seminar in HTR Reactor has become routine activities held in BATAN since 1994. This Seminar is a continuation of the Seminar on Technology and HTR Application held by Centre for Development of Advanced Reactor System. The theme of the seminar is Role, Challenge, Opportunity of HTR in the Twenty-first Century. Thirteen papers presented in the seminar were collected into proceedings. The aims of the proceedings is to provide information and references on nuclear technology, mainly on HTR technology. (DII)

Analysis of Seismic Soil-Structure Interaction for a Nuclear Power Plant (HTR-10

Directory of Open Access Journals (Sweden)

Xiaoxin Wang

2017-01-01

Full Text Available The response of nuclear power plants (NPPs to seismic events is affected by soil-structure interactions (SSI. In the present paper, a finite element (FE model with transmitting boundaries is used to analyse the SSI effect on the response of NPP buildings subjected to vertically incident seismic excitation. Analysis parameters that affect the accuracy of the calculations, including the dimension of the domain and artificial boundary types, are investigated through a set of models. A numerical SSI analysis for the 10 MW High Temperature Gas Cooled Test Reactor (HTR-10 under seismic excitation was carried out using the developed model. The floor response spectra (FRS produced by the SSI analysis are compared with a fixed-base model to investigate the SSI effect on the dynamic response of the reactor building. The results show that the FRS at foundation level are reduced and those at higher floor levels are altered significantly when taking SSI into account. The peak frequencies of the FRS are reduced due to the SSI, whereas the acceleration at high floor levels is increased at a certain frequency range. The seismic response of the primary system components, however, is reduced by the analysed SSI for the HTR-10 on the current soil site.

The development on-line monitoring system of active magnetic bearings for HTR-10GT

International Nuclear Information System (INIS)

Shi Zhengang; Shi Lei; Zha Meisheng; Yu Suyuan

2005-01-01

High Temperature Gas-cooled Reactor (HTR) is recognized as an advanced type of reactor incorporating many design enhancements such as inherent safety features, fuel cycle flexibility, highly fuel utilization, highly efficient electricity generation and process heat application. The research and development of HTR started at the middle of the 1970's, and came to be a part of the Chinese High Technology Program in 1986. A plan to build a 10 MW High Temperature Gas-cooled Reactor (HTR-10) was approved by the State Science and Technology Commission in 1990, and in 1995 the construction was initiated at the Institute of Nuclear Energy Technology (INET), Tsinghua University. The full power 10 MW operation for 72 hours have reached in 2003, and have been checked and accepted by the State Science and Technology Commission. In order to advance the HTR-10 performance, the project of the Helium Gas Turbine Generator for the HTR-10 was authorized by the State Science and Technology Commission, and stared in 2003. In this project, active magnetic bearings (AMBs) are chosen to support the generator rotor and the turbocompressor rotor in the power conversion unit because of their numerous advantages over the conventional bearings. In order to detect how the AMB system works in operation and make diagnosis whether the system behaves normally or not, the monitoring system based on the virtual instruments is designed to monitor the working conditions of the PCU, and to ensure its normal operation. This monitoring system consists of the industry personal computer (PC), the data acquisition system, the measurement transmitters and the LabVIEW system platform. It is located at the PCU control room, and communicates with the master control room by Controller Area Net (CAN). The development is divided into the following three steps: First, a data acquisition platform to collect and acquire all the necessary and useful data from the operation of the AMB system is developed. Second, the

Oxidation of carbon based material for innovative energy systems (HTR, fusion reactor): status and further needs

International Nuclear Information System (INIS)

Moormann, R.; Hinssen, H.K.; Latge, Ch.; Dumesnil, J.; Veltkamp, A.C.; Grabon, V.; Beech, D.; Buckthorpe, D.; Dominguez, T.; Krussenberg, A.K.; Wu, C.H.

2000-01-01

Following an overview on kinetics of carbon/gas reactions, status and further needs in selected safety relevant fields of graphite oxidation in high temperature reactors (HTRs) and fusion reactors are outlined. Kinetics was detected due to the presence of such elements as severe air ingress, lack of experimental data on Boudouard reaction and a similar lack of data in the field of advanced oxidation. The development of coatings which protect against oxidation should focus on stability under neutron irradiation and on the general feasibility of coatings on HTR pebble fuel graphite. Oxidation under normal operation of direct cycle HTR requires examinations of gas atmospheres and of catalytic effects. Advanced carbon materials like CFCs and mixed materials should be developed and tested with respect to their oxidation resistance in a common HTR/fusion task. In an interim HTR, fuel storage radiolytic oxidation under normal operation and thermal oxidation in accidents have to be considered. Plans for future work in these fields are described. (authors)

Possibility of using gamma radiation from HTR reactors for the processing of food and medical products

International Nuclear Information System (INIS)

Pahladsingh, R.R.

2004-01-01

During the fission process in most of the presently operating nuclear reactors nuclear energy is converted into thermal energy and transferred to common steam cycles for power generation. As part of the fission process also α, β and neutrons particles are released from the nucleus; the release of gamma-rays is also a part of the fission process. In present nuclear reactors α, β, neutrons particles and particularly gamma-rays are not gainfully used as a result of the reactor design and of the containment. These plants are built as required by regulations and international standards for safety. The inherently safe HTR reactor, by its physics and design, does not need a special reinforced containment and it is worth looking into the possibilities of this design feature to use the by-products, such as Gamma-rays, from nuclear fission. In the HTR Pebble Bed Reactors the α, and β particles will remain in the kernels of the pebbles. This means that only the neutron particles and gamma-rays will be available outside the reactor pressure vessel. In this report a proposal is presented to use the gamma-rays of the HTR reactor for irradiation of food and agricultural produce. For neutron shielding a reflector is placed inside the reactor while outside the reactor neutron- and thermal-shielding will be accomplished with water. The high energy gamma-rays will pass through the water-shield and could be harnessed for radiation processing of food and medical products. (author)

Present status of research and development for HTR in China

Energy Technology Data Exchange (ETDEWEB)

Dazhong, Wang; Daxin, Zhong; Yuanhul, Xu [Institute of Nuclear Energy Technology, Tsinghua University, Beijing (China)

1990-07-01

The HTR R and D Project is being carried out in the relevant institutions in China. Some topics are covered such as, fuel element technology, graphite development, fuel element handling system, helium technology, fuel reprocessing technology as well as HTR design study. Some results of HTR research work are described. In addition, to provide a test facility for investigation of HTR Module reactor safety and process heat application of HTR, a joint project on building a 10 MW test HTR with Siemens-Interatom, KFA Juelich and INET is going on. The conceptual design of 10 MW test HTR has been completed by the joint group. In parallel the application study of HTR Module is being carried out for the oil industry, petrochemical industry as well as power generation. Some preliminary results of the application study, for example, for heavy oil recovery on Shengli oil field and process heat application in Yan shan petroleum company, are described. (author)

A synthesis on the HTR scenario studies at CEA - HTR2008-58059

International Nuclear Information System (INIS)

Boucher, L.; Greneche, D.

2008-01-01

The aim of the studies is to assess the impact of the deployment of an HTR park replacing one part of the current PWR reactors. The other part of the current park is replaced by EPRs. In these scenarios, the annual electricity production is constant at 400 TWhe. This value corresponds roughly to the present nuclear electricity production in France. From 2002 to 2007, an important program study on HTR has been carried out by CEA and AREVA NC under the joint CEA - AREVA NC project 'prospective studies on the management of Plutonium and the back end of the cycle'. This program addresses core physic and scenario studies, and also the back end of the fuel cycle : reprocessing of spent fuel and HTR waste management. Some core physic studies have already been presented in the reference [1]. This paper presents the results of the scenario studies using two concepts: either the standard core of the Gas Turbine Modular Helium Reactor concept (GTMHR) with Uranium or Plutonium fuel, or the Multiple Fuel Rows Core (MFRC) dedicated to the actinide burning. The insertion of a new concept (fuel, reactor, process) must be evaluated in the global electronuclear system with an analysis of the impact on the fuel cycle (Enrichment, Fuel Fabrication, Reactor, Processing, Interim Storage, Waste storage). The scenario studies are used to evaluate different solutions to manage nuclear materials (uranium, plutonium) and wastes (minor actinides and fission products), from the present situation in France (closed cycle with storage of used MOX fuels) until the final equilibrium: mixed nuclear park with EPR and HTR. These studies allow to calculate material flows and inventories of these elements in each step of the fuel cycle. The simulation of transient scenarios from the present situation to the future situation is performed with the COSI code. HTR reactors feature a high flexibility with regard to fuel cycle options. Several versions of core have been investigated, with different type of

A network-based system of simulation, control and online assistance for HTR-10

Energy Technology Data Exchange (ETDEWEB)

Zhu Shutang [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China)], E-mail: zhust@tsinghua.edu.cn; Luo Shaojie; Shi Lei [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China)

2008-07-15

A network-based computer system has been developed for HTR-10. This system integrates three subsystems: the simulation subsystem (SIMUSUB), the visualized control designed subsystem (VCDSUB) and the online assistance subsystem (OASUB). The SIMUSUB consists of four functional elements: the simulation calculating server (SCS), the main control client (MCC), the data disposal client (DDC) and the results graphic display client (RGDC), all of which can communicate with each other via network. It is intended to analyze and calculate physical processes of the reactor core, the main loop system and the steam generator, etc., as well as to simulate the normal operational and transient accidents. The result data can be dynamically displayed through the RGDC. The VCDSUB provides a platform for control system modeling where the control flow systems can be automatically generated and graphically simulated. Based on the data from the field bus, the OASUB provides some of the reactor core parameters, which are difficult to measure. This integrated system can be used as an educational tool to understand the design and operational characteristics of the HTR-10, and can also provide online support for operators in the main control room, or as a convenient powerful tool for the control system design.

A network-based system of simulation, control and online assistance for HTR-10

International Nuclear Information System (INIS)

Zhu Shutang; Luo Shaojie; Shi Lei

2008-01-01

A network-based computer system has been developed for HTR-10. This system integrates three subsystems: the simulation subsystem (SIMUSUB), the visualized control designed subsystem (VCDSUB) and the online assistance subsystem (OASUB). The SIMUSUB consists of four functional elements: the simulation calculating server (SCS), the main control client (MCC), the data disposal client (DDC) and the results graphic display client (RGDC), all of which can communicate with each other via network. It is intended to analyze and calculate physical processes of the reactor core, the main loop system and the steam generator, etc., as well as to simulate the normal operational and transient accidents. The result data can be dynamically displayed through the RGDC. The VCDSUB provides a platform for control system modeling where the control flow systems can be automatically generated and graphically simulated. Based on the data from the field bus, the OASUB provides some of the reactor core parameters, which are difficult to measure. This integrated system can be used as an educational tool to understand the design and operational characteristics of the HTR-10, and can also provide online support for operators in the main control room, or as a convenient powerful tool for the control system design

HTR-PM Safety requirement and Licensing experience

International Nuclear Information System (INIS)

Li Fu; Zhang Zuoyi; Dong Yujie; Wu Zongxin; Sun Yuliang

2014-01-01

HTR-PM is a 200MWe modular pebble bed high temperature reactor demonstration plant which is being built in Shidao Bay, Weihai, Shandong, China. The main design parameters of HTR-PM were fixed in 2006, the basic design was completed in 2008. The review of Preliminary Safety Analysis Report (PSAR) of HTR-PM was started in April 2008, completed in September 2009. In general, HTR- PM design complies with the current safety requirement for nuclear power plant in China, no special standards are developed for modular HTR. Anyway, Chinese Nuclear Safety Authority, together with the designers, developed some dedicated design criteria for key systems and components and published the guideline for the review of safety analysis report of HTR-PM, based on the experiences from licensing of HTR-10 and new development of nuclear safety. The probabilistic safety goal for HTR-PM was also defined by the safety authority. The review of HTR-PM PSAR lasted for one and a half years, with 3 dialogues meetings and 8 topics meetings, with more than 2000 worksheets and answer sheets. The heavily discussed topics during the PSAR review process included: the requirement for the sub-atmospheric ventilation system, the utilization of PSA in design process, the scope of beyond design basis accidents, the requirement for the qualification of TRISO coating particle fuel, and etc. Because of the characteristics of first of a kind for the demonstration plant, the safety authority emphasized the requirement for the experiment and validation, the PSAR was licensed with certain licensing conditions. The whole licensing process was under control, and was re-evaluated again after Fukushima accident to be shown that the design of HTR-PM complies with current safety requirement. This is a good example for how to license a new reactor. (author)

The Preliminary GAMMA Code Thermal hydraulic Analysis for the Steady State of HTR-10 Initial Core

Energy Technology Data Exchange (ETDEWEB)

Jun, Ji Su; Lim, Hong Sik; Lee, Won Jae

2006-07-15

This report describes the preliminary thermalhydraulic analysis of HTR-10 steady state full power initial core to provide a benchmark calculation of VHTGR(Very High-Temperature Gas-Cooled Reactors) safety analysis code of GAMMA(GAs Multicomponent Mixture Analysis). The input data of GAMMA code are produced for the models of fluid block, wall block, radiation heat transfer and each component material properties in HTR-10 reactor. The temperature and flow distributions of HTR-10 steady state 10 MW{sub th} full power initial core are calculated by GAMMA code with boundary conditions of total reactor inlet flow rate of 4.32 kg/s, inlet temperature of 250 .deg. C, inlet pressure of 3 MPa, outlet pressure of 2.992 MPa and the fixed temperature at RCCS water cooling tube of 50 .deg C. The calculation results are compared with the measured solid material temperatures at 22 fixed instrumentation positions in HTR-10. The wall temperature distribution in pebble bed core shows that the minimum temperature of 358 .deg. C is located at upper core, a higher temperature zone than 829 .deg. C is located at the inner region of 0.45 m radius at the bottom of core centre, and the maximum wall temperature is 897 .deg. C. The wall temperatures linearly decreases at radially and axially farther side from the bottom of core centre. The maximum temperature of RPV is 230 .deg. C, and the maximum values of fuel average temperature and TRISO centreline temperature are 907 .deg. C and 929 .deg. C, respectively and they are much lower than the fuel temperature limitation of 1230 .deg. C. The comparsion between the GAMMA code predictions and the measured temperature data shows that the calculation results are very close to the measured values in top and side reflector region, but a great difference is appeared in bottom reflector region. Some measured data are abnormally high in bottom reflector region, and so the confirmation of data is necessary in future. Fifteen of twenty two data have a

Design of reactor protection systems for HTR plants generating electric power and process heat problems and solutions

International Nuclear Information System (INIS)

Craemer, B.; Dahm, H.; Spillekothen, H.G.

1982-06-01

The design basis of the reactor protection system (RPS) for HTR plants generating process heat and electric power is briefly described and some particularities of process heat plants are indicated. Some particularly important or exacting technical measuring positions for the RPS of a process heat HTR with 500 MWsub(th) power (PNP 500) are described and current R + D work explained. It is demonstrated that a particularly simple RPS can be realized in an HTR with modular design. (author)

Current status and technical description of Chinese 2 x 250 MWth HTR-PM demonstration plant

International Nuclear Information System (INIS)

Zhang Zuoyi; Wu Zongxin; Wang Dazhong; Xu Yuanhui; Sun Yuliang; Li Fu; Dong Yujie

2009-01-01

After the nuclear accidents of Three Mile Island and Chernobyl the world nuclear community made great efforts to increase research on nuclear reactors and to develop advanced nuclear power plants with much improved safety features. Following the successful construction and a most gratifying operation of the 10 MW th high-temperature gas-cooled test reactor (HTR-10), the Institute of Nuclear and New Energy Technology (INET) of Tsinghua University has developed and designed an HTR demonstration plant, called the HTR-PM (high-temperature-reactor pebble-bed module). The design, having jointly been carried out with industry partners from China and in collaboration of experts worldwide, closely follows the design principles of the HTR-10. Due to intensive engineering and R and D efforts since 2001, the basic design of the HTR-PM has been finished while all main technical features have been fixed. A Preliminary Safety Analysis Report (PSAR) has been compiled. The HTR-PM plant will consist of two nuclear steam supply system (NSSS), so called modules, each one comprising of a single zone 250 MW th pebble-bed modular reactor and a steam generator. The two NSSS modules feed one steam turbine and generate an electric power of 210 MW. A pilot fuel production line will be built to fabricate 300,000 pebble fuel elements per year. This line is closely based on the technology of the HTR-10 fuel production line. The main goals of the project are two-fold. Firstly, the economic competitiveness of commercial HTR-PM plants shall be demonstrated. Secondly, it shall be shown that HTR-PM plants do not need accident management procedures and will not require any need for offsite emergency measures. According to the current schedule of the project the completion date of the demonstration plant will be around 2013. The reactor site has been evaluated and approved; the procurement of long-lead components has already been started. After the successful operation of the demonstration plant

A Small Modular Reactor Design for Multiple Energy Applications: HTR50S

Energy Technology Data Exchange (ETDEWEB)

Yan, X.; Tachibana, Y.; Ohashi, H.; Sato, H.; Tazawa, Y.; Kunitomi, K. [Japan Atomic Energy Agency, Ibaraki (Japan)

2013-06-15

HTR50S is a small modular reactor system based on HTGR. It is designed for a triad of applications to be implemented in successive stages. In the first stage, a base plant for heat and power is constructed of the fuel proven in JAEA's 950 .deg. C, 30MWt test reactor HTTR and a conventional steam turbine to minimize development risk. While the outlet temperature is lowered to 750 .deg. C for the steam turbine, thermal power is raised to 50MWt by enabling 40% greater power density in 20% taller core than the HTTR. However the fuel temperature limit and reactor pressure vessel diameter are kept. In second stage, a new fuel that is currently under development at JAEA will allow the core outlet temperature to be raised to 900 .deg. C for the purpose of demonstrating more efficient gas turbine power generation and high temperature heat supply. The third stage adds a demonstration of nuclear-heated hydrogen production by a thermochemical process. A licensing approach to coupling high temperature industrial process to nuclear reactor will be developed. The low initial risk and the high longer-term potential for performance expansion attract development of the HTR50S as a multipurpose industrial or distributed energy source.

International HTR activities

International Nuclear Information System (INIS)

Baust, E.; Weisbrodt, I.

1989-01-01

Asea Brown Boveri AG (ABB) and their subsidiary High Temperature Reactor Construction GmbH (HRB) have brought the pebble bed high temperature reactor to the edge of being ready for the market with the construction and operation of the AVR reactor at Juelich and the THTR 300 at Hamm-Uentrop. Siemens/Interatom have developed the HTR modular concept and, together with their partners HRB, KFA, Rheinbraun Bergbauforschung have taken the nuclear process heat project to its present advanced state of development. The further introduction of the HTR to the market is a long-term objective, due to the present market situation. ABB and Siemens AG have therefore agreed to collaborate by forming a joint company. (orig.)

7th International Topical Meeting on High Temperature Reactor Technology: The modular HTR is advancing towards reality. Papers and Presentations

International Nuclear Information System (INIS)

2014-01-01

HTR2014 aimed at providing an international platform for researchers, engineers and industrial professionals to share their innovative ideas, valuable experience and recent progresses on high temperature gas-cooled reactor (HTR) and its application technologies.

Fabrication technology of spherical fuel element for HTR-10

International Nuclear Information System (INIS)

He Jun; Zou Yanwen; Liang Tongxiang; Qiu Xueliang

2002-01-01

R and D on the fabrication technology of the spherical fuel elements for the 10 MW HTR Test Module (HTR-10) began from 1986. Cold quasi-isostatic molding with a silicon rubber die is used for manufacturing the spherical fuel elements.The fabrication technology and the graphite matrix materials were investigated and optimized. Twenty five batches of fuel elements, about 11000 of the fuel elements, have been produced. The cold properties of the graphite matrix materials satisfied the design specifications. The mean free uranium fraction of 25 batches was 5 x 10 -5

KWU's modular approach to HTR commercialization

International Nuclear Information System (INIS)

Frewer, H.; Weisbrodt, I.

1983-01-01

As a way of avoiding the uncertainties, delays and unacceptable commercial risks which have plagued advanced reactor projects in Germany, KWU is advocating a modular approach to commercialization of the high-temperature reactor (HTR), using small size standard reactor units. KWU has received a contract for the study of a co-generation plant based on this modular system. Features of the KWU modular HTR, process heat, gasification, costs and future development are discussed. (UK)

Nuclear graphite wear properties and estimation of graphite dust production in HTR-10

Energy Technology Data Exchange (ETDEWEB)

Luo, Xiaowei, E-mail: xwluo@tsinghua.edu.cn; Wang, Xiaoxin; Shi, Li; Yu, Xiaoyu; Yu, Suyuan

2017-04-15

Highlights: • Graphite dust. • The wear properties of graphite. • Pebble bed. • High Temperature Gas-cooled Reactor. • Fuel element. - Abstract: The issue of the graphite dust has been a research focus for the safety of High Temperature Gas-cooled Reactors (HTGRs), especially for the pebble bed reactors. Most of the graphite dust is produced from the wear of fuel elements during cycling of fuel elements. However, due to the complexity of the motion of the fuel elements in the pebble bed, there is no systematic method developed to predict the amount the graphite dust in a pebble bed reactor. In this paper, the study of the flow of the fuel elements in the pebble bed was carried out. Both theoretical calculation and numerical analysis by Discrete Element Method (DEM) software PFC3D were conducted to obtain the normal forces and sliding distances of the fuel elements in pebble bed. The wearing theory was then integrated with PFC3D to estimate the amount of the graphite dust in a pebble bed reactor, 10 MW High Temperature gas-cooled test Reactor (HTR-10).

State of the Art of helium heat exchanger development for future HTR-projects - HTR2008-58146

International Nuclear Information System (INIS)

Esch, M.; Juergens, B.; Hurtado, A.; Knoche, D.; Tietsch, W.

2008-01-01

In Germany two HTR nuclear power plants had been built and operated, the AVR-15 and the THTR-300. Also various projects for different purposes in a large power range had been developed, The AVR-15, an experimental reactor with a power output of 15 MWel was operated for more than 20 years with excellent results. The THTR-300 was designed as a prototype demonstration plant with 300 MWel and should be the technological basis for the entire future reactor line. The THTR-300 was prematurely shut down and decommissioned because of political reasons. But because of the accompanying comprehensive R and D program and the operation time of about 5 years, the technology was proved and essential operational results were gained. The AVR steam generator was installed above the reactor core. The six THTR heat exchangers were arranged circularly around the reactor core, Both heat exchanger systems have been operated successfully and furthermore acted as a residual heat removal system. The technology knowledge and experience gained on these existing HTR plants is still available at Westinghouse Electric Germany GmbH since Westinghouse is one of the legal successors of the former German HTR companies. As a follow-up project of THTR, the HTR-500 was developed and designed up to the manufacturing stage. For this plant additionally to the 8 steam generators, two residual heat removal heat exchangers were foreseen. These were to be installed in a ring around the reactor core. All these HTRs were designed for the generation of electricity using a steam cycle. Extensive research work has also been done for advanced applications of HTR technology e.g. using a direct cycle within the HHT project or generating process heat within the framework of the PNP project, Because of the critical attitude of the German government to the nuclear power in the past 20 years in Germany there was only a very limited interest in the further development of the HTR technology. As a consequence of the German

Introduction of HTR-PM Operation and Fuel Management System

International Nuclear Information System (INIS)

Liu Fucheng; Luo Yong; Gao Qiang

2014-01-01

There is a big difference between High Temperature Gas-cooled Reactor Pebble-modules Demonstration Project(HTR-PM) and PWR in operation mode. HTR-PM is a continually refuelled reactor, and the operation and fuel management of it, which affect each other, are inseparable. Therefore, the analysis of HTR-PM fuel management needs to be carried out “in real time”. HTR-PM operation and fuel management system is developed for on-power refuelling mode of HTR-PM. The system, which calculates the core neutron flux and power distribution, taking high-temperature reactor physics analysis software-VSOP as a basic tool, can track and predict the core state online, and it has the ability to restructure core power distribution online, making use of ex-core detectors to correct and check tracking calculation. Based on the ability to track and predict, it can compute the core parameters to provide support for the operation of the reactor. It can also predict the operation parameters of the reactor to provide reference information for the fuel management.The contents of this paper include the development purposes, architecture, the main function modules, running process, and the idea of how to use the system to carry out HTR-PM fuel management. (author)

The Renewal of HTR Development in Europe

International Nuclear Information System (INIS)

Hittner, Dominique

2002-01-01

The European HTR-Technology Network (HTR-TN), created in 2000, presently groups 20 organisations from European nuclear research and industry for developing the technologies of direct-cycle modular HTRs, which presently raise a large world-wide interest, because of their high potential for economic competitiveness, natural resource sparing, safety and minimisation of the waste impacts, in line with the goals of sustainable development of Generation IV. All aspects of HTR technologies are addressed by HTR-TN, from the reactor physics to the development of materials, fuel and components. Most of this activity is supported by the European Commission in the frame of its 5. EURATOM Framework Programme. The first results of HTR-TN programme are given: the analysis of the reactor physics international benchmark on the commissioning tests of HTTR (Japan), the long term behaviour of spent HTR fuel in geologic disposal conditions, the preparation of a very high burnup fuel irradiation and the development of fabrication processes for producing high performance coated particles, etc. (authors)

Testing of HTR UO{sub 2} TRISO fuels in AVR and in material test reactors

Energy Technology Data Exchange (ETDEWEB)

Kania, Michael J., E-mail: MichaelJKania@googlemail.com [Retired from Lockheed Martin Corp, 20 Beach Road, Averill Park, NY 12018 (United States); Nabielek, Heinz, E-mail: heinznabielek@me.com [Retired from Research Center Jülich, Monschauerstrasse 61, 52355 Düren (Germany); Verfondern, Karl [Research Center Juelich,Research Center Jülich, Institute of Energy and Climate Research, 52425 Jülich (Germany); Allelein, Hans-Josef [Research Center Juelich,Research Center Jülich, Institute of Energy and Climate Research, 52425 Jülich (Germany); RWTH Aachen, 52072 Aachen (Germany)

2013-10-15

The German High Temperature Reactor Fuel Development Program successfully developed, licensed and manufactured many thousands of spherical fuel elements that were used to power the experimental AVR reactor and the commercial THTR reactor. In the 1970s, this program extended the performance envelope of HTR fuels by developing and qualifying the TRISO-coated particle system. Irradiation testing in real-time AVR tests and accelerated MTR tests demonstrated the superior manufacturing process of this fuel and its irradiation performance. In the 1980s, another program direction change was made to a low enriched UO{sub 2} TRISO-coated particle system coupled with high-quality manufacturing specifications designed to meet new HTR plant design needs. These needs included requirements for inherent safety under normal operation and accident conditions. Again, the German fuel development program met and exceeded these challenges by manufacturing and qualifying the low-enriched UO{sub 2} TRISO-fuel system for HTR systems with steam generation, gas-turbine systems and very high temperature process heat applications. Fuel elements were manufactured in production scale facilities that contained near defect free UO{sub 2} TRISO coated particles, homogeneously distributed within a graphite matrix with very low levels of uranium contamination. Good irradiation performance for these elements was demonstrated under normal operating conditions to 12% FIMA and under accident conditions not exceeding 1600 °C.

Technology assessment HTR. Part 4. Power upscaling of High Temperature Reactors

International Nuclear Information System (INIS)

Van Heek, A.I.

1996-06-01

Designs of nuclear reactors can be classified in evolutionary, revolutionary and innovative designs. An innovative design is the High Temperature Reactor (HTR). Introduction of innovative reactors has not been successful until now. Globally, three requirements for this reactors for successful market introduction can be identified: (1) Societal support for nuclear energy, or if separable, for this reactor type, should be repaired; (2) After market introduction the innovative plant must be able to operate economically competitive; and (3) The costs of market introduction of an innovative reactor design must be limited. Until now all reactor designs classified as innovative have not yet been realized. High temperature reactors exist in many different designs. Common features are: helium coolant, graphite moderator and coated particle fuel. The combination of these creates the potential to fulfill the first requirement (public support), and similarly a hurdle to the second requirement (economical operation). All three problems existing in the eyes of the public are addressed, while a high degree of transparency is reached, making the design understandable also by others than nuclear experts. A consequence of designing according to the social support requirement is a limitation of the unit power level. The usual method to make nuclear power plants economically competitive, i.e. just raising the power level (economy of scale) could not be applied anymore. Therefore other means of cost decreasing had to be used: modularization and simplification. These ideas are explained. Since all existing HTRs are currently out of operation, additional experience from two small HTRs under construction at this moment in the Far East will be essential. In the history of HTR designs, an evolutionary path can be identified. The early designs had a philosophy of safety and economics very similar to those of LWR. Modularization was introduced to attain economic viability and the design was

Instrumentation of steam cycle HTR's up to 900 MWe

International Nuclear Information System (INIS)

Leithner, D.E.; Winkenbach, B.

1982-06-01

Due to basic design features and inherent safety qualities in-core instrumentation is not needed in an HTR. Reactor safety requirements can be met by integral measurements. A modest spatial resolving power of the out-of-core instrumentation is sufficient for all operational purposes in small and medium sized steam cycle HTR's. Thus, the instrumentation concept of the THTR 300 MWe prototype reactor can be adopted without major changes for the HTR 450 MWe reactor project, as is demonstrated here for the neutron flux and temperature measurements. (author)

Status of the HTR 500 design program

International Nuclear Information System (INIS)

Baust, E.; Arndt, E.

1987-01-01

Since 1982 BBC/HRB have offered the HTR 500 as the follow-on project of the THTR 300, the first large pebble bed reactor. The technical concept of the HTR-500 largely corresponds to the THTR 300 which has been in operation for almost 2 years now. In developing the design concept of the HTR 500 the ideas and demands of the reactor users in the FRG interested in the HTR have been taken into consideration to a large extent. In 1982 these potential users formed a working group 'Arbeitsgemeinschaft Hochtemperaturreaktor' (AHR), representing 16 power indusry companies and in early 1983, awarded a contract to HRB to perform a conceptual design study on the HTR 500. Within this conceptual design study BBC/HRB developed the safety concept of the HTR 500, prepared a detailed description of the overall power plant, and performed a cost calculation. These activities were completed in 1984. Based on the positive results of this conceptual design study, BBC/HRB are expecting to be granted a design contract by the users company Hochtemperaturreaktor GmbH (HRG) to establish the final complete design plans and documents for the HTR 500. (author)

Auxiliary bearing design and rotor dynamics analysis of blower fan for HTR-10

International Nuclear Information System (INIS)

Gao Mingshan; Yang Guojun; Xu Yang; Zhao Lei; Yu Suyuan

2005-01-01

The electromagnetic bearing instead of ordinary mechanical bearing was chosen to support the rotor in the blower fan system with helium of 10 MW high temperature gas-cooled test reactor (HTR-10), and the auxiliary bearing was applied in the HTR-10 as the backup protector. When the electromagnetic bearing doesn't work suddenly for the power broken, the auxiliary bearing is used to support the falling rotor with high rotating speed. The rotor system will be protected by the auxiliary bearing. The design of auxiliary bearing is the ultimate safeguard for the system. This rotor is vertically mounted to hold the blower fan. The rotor's length is about 1.5 m, its weight is about 240 kg and the rotating speed is about 5400 r/min. Auxiliary bearing design and rotor dynamics analysis are very important for the design of blower fan to make success. The research status of the auxiliary bearing was summarized in the paper. A sort of auxiliary bearing scheme was proposed. MSC.Marc was selected to analyze the vibration mode and the natural frequency of the rotor. The scheme design of auxiliary bearing and analysis result of rotor dynamics offer the important theoretical base for the protector design and control system of electromagnetic bearing of the blower fan. (authors)

Studi Model Benchmark Mcnp6 Dalam Perhitungan Reaktivitas Batang Kendali Htr-10

OpenAIRE

Jupiter S.Pane, Zuhair, Suwoto, Putranto Ilham Yazid

2016-01-01

STUDI MODEL BENCHMARK MCNP6 DALAM PERHITUNGAN REAKTIVITAS BATANG KENDALI HTR-10. Dalam operasi reaktor nuklir, sistem batang kendali memainkan peranan yang sangat penting karena didesain untuk mengendalikan reaktivitas teras dan memadamkan reaktor. Nilai reaktivitas batang kendali harus diprediksi secara akurat melalui eksperimen dan perhitungan. Makalah ini mendiskusikan model Benchmark dalam perhitungan reaktivitas batang kendali reaktor HTR-10. Perhitungan dikerjakan dengan program transpo...

The HTR safety concept demonstrated by selected examples

International Nuclear Information System (INIS)

Sommer, H.; Stoelzl, D.

1981-01-01

The licensing experience gained in the Federal Republic of Germany is based on the licensing procedures for the THTR-300 and the HTR-1160. In the course of the licensing procedures for these reactors a safety concept for an HTR has been developed. This experience constitutes the basis for the design of future HTR's. (author)

Future Development of Modular HTGR in China after HTR-PM

International Nuclear Information System (INIS)

Zhang Zuoyi; Wang, Haitao; Dong Yujie; Li Fu

2014-01-01

The modular high temperature gas-cooled reactor (MHTGR) is an inherently safe nuclear energy technology for efficient electricity generation and process heat applications. The MHTGR is promising in China as it may replace fossil fuels in broader energy markets. In line with China’s long-term development plan of nuclear power, the Institute of Nuclear and New Energy Technology (INET) of Tsinghua University developed and designed a MHTGR demonstration plant, named high-temperature gas-cooled reactor-pebble bed module (HTR-PM). The HTR-PM came into the construction phase at the end of 2012. The HTR-PM aims to demonstrate safety, economic potential and modularization technologies towards future commercial applications. Based on experiences obtained from the HTR-PM project with respect to design, manufacture, construction, licensing and project management, a further step aiming to promote commercialization and market applications of the MHTGR is expected. To this purpose, INET is developing a commercialized MHTGR named HTR-PM600 and a conceptual design is under way accordingly. HTR-PM600 is a pebble-bed MHTGR power generation unit with a six-pack of 250MWth reactor modules. The objective is to cogenerate electricity and process heat flexibly and economically in order to meet a variety of market needs. The design of HTR-PM600 closely follows HTR-PM with respect to safety features, system configuration and plant layout. HTR-PM600 has the six modules feeding one steam turbine to generate electricity with capacity to extract high temperature steam from various interfaces of the turbine for further process heat applications. A standard plant consists of two HTR-PM600 units. Based on the economic information of HTR-PM, a preliminary study is carried out on the economic prospect of HTR-PM600. (author)

Predictions on an HTR coolant composition after operational experience with experimental reactors

International Nuclear Information System (INIS)

Nieder, R.

1981-01-01

Long-term operational experience of the HTR experimental reactors Dragon (1966 - 1975), Peach Bottom (1967 - 1974) and AVR (since 1967) has yielded a large number of common quantitative and qualitative results about the sources and behaviour of helium impurities in the primary circuits. Additional information has also been obtained from experiments made at the three reactors. The results at the AVR are particularly interesting because the gas outlet temperature can be varied from 770 0 C to 950 0 C when the reactor power is kept constant. Hence they can be studied according to the temperature dependence of all chemical reactions. It should be possible to apply the results from the operating measurements and experiments made at the reactors, in particular the interrelation of the impurity concentrations, to future reactors. The absolute values of these impurity concentrations are obtained first and foremost by the corresponding helium purification constants

Design and application of the HTR-100 industrial nuclear power plant

International Nuclear Information System (INIS)

Brandes, S.; Kohl, W.

1988-01-01

The small HTR-100 high temperature reactor combines the reactor concept of the AVR reactor, which has been proven for 20 years, with the latest component technology of the THTR power plant which has been in operation since 1985. The nuclear heat supply system is conceived so as to be applicable for the generation of electric power, district heat and process steam according to the customer's demand. The HTR-100 reactor has a thermal power of 258 MW and offers steam parameters of 190 bar/530 0 C. To cover a higher power demand HTR-100 reactors can be combined forming a larger power plant. Economic analyses have shown competitiveness with fossil power plants. (orig.)

Simulation of thermal-hydraulic process in reactor of HTR-PM based on flow and heat transfer network

International Nuclear Information System (INIS)

Zhou Kefeng; Zhou Yangping; Sui Zhe; Ma Yuanle

2012-01-01

The development of HTR-PM full scale simulator (FSS) is an important part in the project. The simulation of thermal-hydraulic process in reactor is one of the key technologies in the development of FSS. The simulation of thermal-hydraulic process in reactor was studied. According to the geometry structures and the characteristics of thermal-hydraulic process in reactor, the model was setup in components construction way. Based on the established simulation method of flow and heat transfer network, a Fortran code was developed and the simulation of thermal-hydraulic process was achieved. The simulation results of 50% FP steady state, 100% FP steady state and control rod mistakenly ascension accidents were given. The verification of simulation results was carried out by comparing with the design and analysis code THERMIX. The results show that the method and model based on flow and heat transfer network can meet the requirements of FSS and reflect the features of thermal-hydraulic process in HTR-PM. (authors)

Technology assessment HTR. Part 3. Economics of new concept of the modular High Temperature Reactor

International Nuclear Information System (INIS)

Lako, P.

1996-06-01

In this study the economic feasibility of new concepts of the High Temperature Reactor were investigated. These new concepts are characterized as inherently safe. The different concepts were used as industrial heat/power reactors and compared with a gas fired Steam and Gas turbine installation. The best economic advantages are offered by a HTR with a Thorium/Uranium cycle as compared with a gas fired steam- and gas turbine. 6 figs, 9 tabs, 21 refs

Advanced Characterization Techniques for Silicon Carbide and Pyrocarbon Coatings on Fuel Particles for High Temperature Reactors (HTR)

Energy Technology Data Exchange (ETDEWEB)

Basini, V.; Charollais, F. [CEA Cadarache, DEN/DEC/SPUA, BP 1, 13108 St Paul Lez Durance (France); Dugne, O. [CEA Marcoule, DEN/DTEC/SCGS BP 17171 30207 Bagnols sur Ceze (France); Garcia, C. [Laboratoire des Composites Thermostructuraux (LCTS), UMR CNRS 5801, 3 allee de La Boetie, 33600 Pessac (France); Perez, M. [CEA Grenoble DRT/DTH/LTH, 17 rue des Martyrs, 38054 Grenoble cedex 9 (France)

2008-07-01

Cea and AREVA NP have engaged an extensive research and development program on HTR (high temperature reactor) fuel. The improving of safety of (very) high temperature reactors (V/HTR) is based on the quality of the fuel particles. This requires a good knowledge of the properties of the four-layers TRISO particles designed to retain the uranium and fission products during irradiation or accident conditions. The aim of this work is to characterize exhaustively the structure and the thermomechanical properties of each unirradiated layer (silicon carbide and pyrocarbon coatings) by electron microscopy (SEM, TEM), selected area electronic diffraction (SEAD), thermo reflectance microscopy and nano-indentation. The long term objective of this study is to define pertinent parameters for fuel performance codes used to better understand the thermomechanical behaviour of the coated particles. (authors)

A new impetus for developing industrial process heat applications of HTR in europe - HTR2008-58259

International Nuclear Information System (INIS)

Hittner, D.; De Groot, S.; Griffay, G.; Yvon, P.; Pienkowski, L.; Ruer, J.; Angulo, C.; Laquaniello, G.

2008-01-01

Due to its high operating temperature (up to 850 deg. C with present technologies, possibly higher in the longer term), and its power range (a few hundred MW), the modular HTR could address a larger scope of industrial process heat needs than other present nuclear systems. Even if HTR can contribute to competitive electricity generation, this potential for industrial heat applications is the main incentive for developing this type of reactor, as it could open to nuclear energy a large non-electricity market. However several issues must be addressed and solved successfully for HTR to actually enter the market of industrial process heat: 1) as an absolute prerequisite, to develop a strategic alliance of nuclear industry and R and D with process heat user industries. 2) to solve some key technical issues, as for instance the design of a reactor and of a coupling system flexible enough to reconcile a single reactor design with multiple applications and versatile requirements for the heat source, and the development of special adaptations of the application processes or even of new processes to fit with the assets and constraints of HTR heat supply, 3) to solve critical industrial issues such as economic competitiveness, availability and 4) to address the licensing issues raised by the conjunction of nuclear and industrial risks. In line with IAEA initiatives for supporting non-electric applications of nuclear energy and with the orientations of the SET-Plan of the European Commission, the (European) HTR Technology Network (HTR-TN) proposes a new project, together with industrial process heat user partners, to provide a first impetus to the strategic alliance between nuclear and non-nuclear industries. End user requirements will be expressed systematically on the basis of inputs from industrial partners on various types of process heat applications. These requirements will be confronted with the capabilities of the HTR heat source, in order to point out possible

The use and development of the high-temperature reactor (HTR) in China. A conference report

International Nuclear Information System (INIS)

Marnet, C.

2001-01-01

Gas-cooled graphite-moderated reactors have been under development since the early days of nuclear technology. Starting with plants in Britain and France, reactors employing this combination of coolant and moderator were used in commercial nuclear power plants in the second half of the fifties. At the same time, efforts seeking to use inert helium gas as a coolant resulted in the construction in several countries, the United States and Germany in particular, of larger nuclear power plants with higher coolant temperatures and the resultant thermodynamic advantages of high efficiencies and the option of process heat generation. Economic and political considerations led to the decommissioning of these plants. Today, research and development of high-temperature reactors are concentrated on smaller units. Work is carried out in close international cooperation, especially on project designs and newly commissioned plants in China (HTR-10), Japan (HTTR, Oarai), And South Africa (ESKOM project), but also in the USA and in Russia. (orig.) [de

Market potential of heat utilization of modular HTR in Japan

International Nuclear Information System (INIS)

Ide, Akira; Tasaka, Kanji.

1993-01-01

HTR is considered to be the most suitable reactor type to use in the field other than power generation. So it is useful to know market potential of this type of reactor in Japan to justify its development. This potential was estimated to be about 400 200MWt modular HTR reactors. This number will be double if the market of hydrogen is developed. (J.P.N.)

Worldwide status of HTR development

International Nuclear Information System (INIS)

1978-06-01

The International Atomic Energy Agency convened a technical committee meeting on high temperature reactors (HTRs) from 12-14 Dec. 1977 at Agency Headquarters to provide a forum for the exchange of information on the status of HTR development programmes and to receive advice on the Agency programme in this field. The continuing high level of international interest in HTRs was evidenced by the participation from 11 countries and 2 organizations: Austria, Belgium, France, Federal Republic of Germany, Japan, Netherlands, Poland, Switzerland, Union of Soviet Socialist Republics, United Kingdom of Great Britain, United States of America, Commission of the European Communities, and the OECD Nuclear Energy Agency. In order to promote the continuing exchange of technical information through the offices of the IAEA, a recommendation was made that the Agency establish a standing International Working Group on High Temperature Reactors (IWGHTR). This recommendation is being implemented in 1978. Considerable information on recent progress in HTR development was present at the technical committee meeting in technical reports and in progress reports on HTR development programmes. Since this material will not be published, this summary report on the worldwide status of HTR development at the beginning of 1978 has been prepared, based primarily on information presented at the December 1977 meeting

State of the art in HTR engineering and design

International Nuclear Information System (INIS)

Baust, E.

1984-11-01

The high-temperature reactor is an universally applicable energy source on the electricity and heat market, providing energy safely, compatible with the environment, and economically. The startup of the THTR-300, which will commence power generation in spring 1985, and the good results of the preparatory tests and studies for the subsequent plant, the HTR-500, created the required preconditions for the placing of an order to commence work to realize the first planning stage of the HTR-500. The order is expected to be placed within short. BBC/HRB has gained a reputation worldwide as the leading manufacturer of HTR plants. BBC/HRB has the know-how to offer HTR plants of various size over the entire capacity range between 100 and 600 MWe, or as twin-type plants up to 1200 MWe, their design being based on the THTR-300 reference plant. The HTR is an uncomplicated reactor system offering many advantages in terms of operation and safety. This reactor type therefore is the system of choice for energy generation for short-range energy supply. The system also is of interest as an export item, and hence is of significance to the economy and to employment policy. (orig.) [de

HTR-TN achievements and prospects for future developments

International Nuclear Information System (INIS)

Hittner, D.; Angulo, C.; Basini, V.; Bogusch, E.; Breuil, E.; Buckthorpe, D.; Chauvet, V.; Futterer, M.A.; Van Heek, A.; Von Lensa, W.; Yvon, P.

2011-01-01

It is already 10 years since the (European) High Temperature Reactor Technology Network (HTR-TN) launched a program for development of HTR technology, which expanded through three successive Euratom framework programs, with many projects in line with the network strategy. Widely relying in the beginning on the legacy of the former European HTR developments (DRAGON, AVR, THTR, etc.) that it contributed to safeguard, this program led to advances in HTR/VHTR technologies and produced significant results, which can contribute to the international cooperation through Euratom involvement in the Generation IV International Forum (GIF). the main achievements of the European program, performed in complement to efforts made in several European countries and other GIF partners, are presented: they concern the validation of computer codes (reactor physics, as well as system transient analysis from normal operation to air ingress accident and fuel performance in normal and accident conditions), materials (metallic materials for vessel, direct cycle turbines and intermediate heat exchanger, graphite, etc.), component development, fuel manufacturing and irradiation behavior, and specific HTR waste management (fuel and graphite). Key experiments have been performed or are still ongoing, like irradiation of graphite and of fuel material (PYCASSO experiment), high burn-up fuel PIE, safety test and isotopic analysis, IHX mock-up thermohydraulic test in helium atmosphere, air ingress experiment for a block type core, etc. Now HTR-TN partners consider that it is time for Europe to go a step forward toward industrial demonstration. In line with the orientations of the 'Strategic Energy Technology Plan (SET-Plan)' recently issued by the European Commission that promotes a strategy for development of low-carbon energy technologies and mentions Generation IV nuclear systems as part of key technologies, HTR-TN proposes to launch a program for extending the contribution of nuclear energy to

On Power Refueling Management of HTR-PM

International Nuclear Information System (INIS)

Sun Furui; Luo Yong; Gao Qiang

2014-01-01

The refueling management is an important work of nuclear power plant , directly affecting its safety and economy. At present, the ordinary commercial pressurized water reactor (PWR) nuclear power plant has developed more mature in the refueling management, and formed a set of relatively complete system and methods.The High Temperature Gas-cooled Reactor Pebble-modules Demonstration Project(HTR-PM) has significant differences with the ordinary PWR nuclear power plant in the fuel morphology and the refueling mode. It adopts the spherical fuel element and the on-power refueling. Therefore, the HTR-PM refueling management has its own unique characteristics, but currently there is no mature experience to use for reference across the world. This paper gives a brief introduction to the HTR-PM on power refueling management, including the refueling management system construction, the refueling strategy, the fuel element internal transportation,charging and discharging, etc. It aims at finding the befitting HTR-PM refueling management methods in view of its own unique characteristics in order to ensure the orderly development of the refueling management and the refueling safety. (author)

Gas cooled HTR

International Nuclear Information System (INIS)

Schweiger, F.

1985-01-01

In the He-cooled, graphite-moderated HTR with spherical fuel elements, the steam generator is fixed outside the pressure vessel. The heat exchangers are above the reactor level. The hot gases stream from the reactor bottom over the heat exchanger, through an annular space around the heat exchanger and through feed lines in the side reflector of the reactor back to its top part. This way, in case of shutdown there is a supplementary natural draught that helps the inner natural circulation (chimney draught effect). (orig./PW)

Seismic research on graphite reactor core

International Nuclear Information System (INIS)

Lai Shigang; Sun Libin; Zhang Zhengming

2013-01-01

Background: Reactors with graphite core structure include production reactor, water-cooled graphite reactor, gas-cooled reactor, high-temperature gas-cooled reactor and so on. Multi-body graphite core structure has nonlinear response under seismic excitation, which is different from the response of general civil structure, metal connection structure or bolted structure. Purpose: In order to provide references for the designing and construction of HTR-PM. This paper reviews the history of reactor seismic research evaluation from certain countries, and summarizes the research methods and research results. Methods: By comparing the methods adopted in different gas-cooled reactor cores, inspiration for our own HTR seismic research was achieved. Results and Conclusions: In this paper, the research ideas of graphite core seismic during the process of designing, constructing and operating HTR-10 are expounded. Also the project progress of HTR-PM and the research on side reflection with the theory of similarity is introduced. (authors)

Overview of Japanese seismic research program for HTR

International Nuclear Information System (INIS)

Ikushima, Takeshi

1978-07-01

In order to obtain the license for construction and operation of HTR developed and introduced into Japan, it is necessary to assure integrity of reactor structures and the capability of reactor shutdown and maintain safety shutdown for the seismic design condition. Because Japanese land is located in relatively high seismacity zone, when an excessive earthquake would occur, the public and plant personnel should be protected from radiation hazard. For the above reason, many efforts of seismic research and development for HTR have been made at institutes and companies in Japan. In the paper, descriptions are: (1) Present status of development and construction plans of HTR, (2) guideline of aseismic design, (3) need of aseismic research, (4) present status of research and development, (5) future plan. (auth.)

HTR core physics and transient analyses by the Panthermix code system

International Nuclear Information System (INIS)

Haas, J.B.M. de; Kuijper, J.C.; Oppe, J.

2005-01-01

At NRG Petten, core physics analyses on High Temperature gas-cooled Reactors (HTRs) are mainly performed by means of the PANTHERMIX code system. Since some years NRG is developing the HTR reactor physics code system WIMS/PANTHERMIX, based on the lattice code WIMS (Serco Assurance, UK), the 3-dimensional steady-state and transient core physics code PANTHER (British Energy, UK) and the 2-dimensional R-Z HTR thermal hydraulics code THERMIX-DIREKT (Research Centre FZJ Juelich, Germany). By means of the WIMS code nuclear data are being generated to suit the PANTHER code's neutronics. At NRG the PANTHER code has been interfaced with THERMIX-DIREKT to form PANTHERMIX, to enable core-follow/fuel management and transient analyses in a consistent manner on pebble bed type HTR systems. Also provisions have been made to simulate the flow of pebbles through the core of a pebble bed HTR, according to a given (R-Z) flow pattern. As examples of the versatility of the PANTHERMIX code system, calculations are presented on the PBMR, the South African pebble bed reactor design, to show the transient capabilities, and on a plutonium burning MEDUL-reactor, to demonstrate the core-follow/fuel management capabilities. For the investigated cases a good agreement is observed with the results of other HTR core physics codes

An evaluation of the results of the HTR fuel programme conducted in the Dragon reactor experiment

International Nuclear Information System (INIS)

Shepherd, L.R.

1982-01-01

The Dragon Reactor Experiment was used over a period of ten years to investigate the behaviour of HTR fuel elements under realistic service conditions. The purpose of the work was to develop fuel capable of meeting the requirements of commercial power reactors. The studies divided into areas concerned with the mechanical behaviour of the graphite core structure under fast neutron irradiation and the ability of the coated particle fuel to retain fissile products over commercially viable life-cycles. (author)

Objectives for an HTR R and D physics programme

Energy Technology Data Exchange (ETDEWEB)

Johnstone, I; Scott, J A

1973-10-15

The paper reviews important objectives for an HTR R and D programme and the importance of particular characteristics for safety and reactor performance is discussed. Uncertainties in the physics characteristics influence reactor design through the inclusion of design margins and contingency allowances and may even eliminate certain design variants. The paper discusses quantitatively the relationship between some important uncertainties and reactor design and operating costs and derives targets for the precision with which it should be possible to compute the corresponding physics characteristics. To extrapolate to power reactor conditions, the need for a comprehensive computational scheme validated by an adequate experimental programme is emphasised. The reduction in uncertainty as the theoretical and experimental reactor physics development proceeds in order to meet the desired target uncertainty is illustrated with respect to the UK's programme in support of the low enriched HTR concept. The current situation for this concept is discussed and compared briefly with that for the Th cycle HTR for which somewhat less zero energy experimental data are available. (auth)

The HTR 500 concept based on pratical THTR and AVR experience

International Nuclear Information System (INIS)

Wachholz, W.; Weicht, U.

1988-01-01

This paper discusses progress during the past ten years in the development of a specific HTR safety concept. This has been mainly characterized by the abandonment of the LWR specific safety principles and making use of the safety characteristics typical of the high-temperature reactor (HTR). In the design, construction and operation of high-temperature reactors - especially AVR (15 MWe plant in Juelich, FRG) and THTR (300 MWe plant in Hamm-Uentrop, FRG) - experience has been gained in the field of accident topology and plant risk of HTRs in recent years. This experience, based on detailed accident analyses performed by manufacturers and experts, is relevant for the entire HTR line independent of specific projects. The authors focus on the HTR 500, the first commercial high temperature reactor with a pebble bed core. Its design principles and the design of its systems are based on the earlier AVR and THTR projects

Engineering and licensing progress of the HTR-Module

Energy Technology Data Exchange (ETDEWEB)

Weisbrodt, I A

1988-07-01

This report deals not only with the latest status of Siemens/Interatom's HTR-Module but also reflects the latest engineering and licensing progress of the HTR-Module against the background of the specified design requirements and of the discussions on passively safe reactors. Therefore, I intend to report also about two examples of the accident analysis - one design basis accident, i.e. the leak-before-break of the reactor pressure vessel and one beyond design accident, i. e. massive water ingress.

Engineering and licensing progress of the HTR-Module

International Nuclear Information System (INIS)

Weisbrodt, I.A.

1988-01-01

This report deals not only with the latest status of Siemens/Interatom's HTR-Module but also reflects the latest engineering and licensing progress of the HTR-Module against the background of the specified design requirements and of the discussions on passively safe reactors. Therefore, I intend to report also about two examples of the accident analysis - one design basis accident, i.e. the leak-before-break of the reactor pressure vessel and one beyond design accident, i. e. massive water ingress

Survey of HTR related research at IRI, Delft, Netherlands

Energy Technology Data Exchange (ETDEWEB)

Hoogenboom, J.E.; Wallerbos, E.J.M.; Van der Hagen, T.H.J.J.; Van Dam, H. [Interfaculty Reactor Institute IRI, Delft University of Technology, Delft (Netherlands); Tuerkcan, E. [ECN Nuclear Research, Petten (Netherlands)

1998-09-01

High temperature helium-cooled reactors have a large potential for inherent safety. Therefore, several projects on HTR research are being carried out or were carried out at the Interfaculty Reactor Institute (IRI) of the Delft University of Technology in Delft, Netherlands. As part of a larger research programme measurements of core reactivity, reactivity worth of safety rods and of small samples being oscillated in the reactor core were carried out at the PROTEUS facility of the Paul Scherrer Institute at Villigen, Switzerland. Together with other partners in the Netherlands a small inherently safe co-generation plant with a pebble-bed HTR core was designed and analysed. It was verified that such a reactor can operate continuously for 10 years by adding continuously fuel pebbles until the maximum available core height is reached. As a new, innovative, inherently safe reactor type the design of a fluidized-bed reactor with coated fuel particles on a helium gas stream is discussed and results are shown for the analysis of inherent criticality safety under varying coolant flow rates. IRI is also taking part in the new IAEA Co-ordinated Research Programme, which involves participation in the start-up experiments of the Japanese HTTR and carrying out calculations for the core physics benchmark test. 11 refs.

Status of development of the HTR module

International Nuclear Information System (INIS)

Weisbrodt, I.A.

1989-01-01

Growing concern about the rising global temperature of the earth due to the ''Greenhouse Effect'' is increasingly focussing worldwide interest on passively safe reactors for heat and power production. In this context the development status of the HTR-Module designed by the Siemens-Group merits strong interest. The HTR-Module has a high degree of passive safety features. Even in case of hypothetical accidents the decay heat is dissipated from the primary system to the environment by passive measures alone i.e. by heat conduction, convection and radiation. The detailed engineering for the HTR-Module continues to progress. In addition to the engineering for the layout considerable progress has been made in the detailed engineering for specific components - e.g. pressure vessel, steam generator, hot gas duct, blower etc. - and specific systems - e.g. first core, helium purification system, reactor safety system, reactor control etc. The procedure for the conceptual licence has been continued. A large number of supplementary analyses and reports have been elaborated and submitted for this procedure. Many workshop meetings have been held with the nominated experts. The hypothetical accidents have been analysed and a special report on these accidents has been submitted. The safety analyses report has been revised, taking into account the results and achievements reached during the ongoing licensing procedure. Parallel to these engineering activities outstanding in R and D work for the HTR-Module, e.g. in the field of fuel elements etc. has been continued. The HTR-Module has found worldwide interest. Respective activities are going on in Bangladesh, PR China, USSR, Indonesia etc. Relevant application studies have been carried out and/or initiated. (author). 15 refs, 16 figs

KüFA safety testing of HTR fuel pebbles irradiated in the High Flux Reactor in Petten

Energy Technology Data Exchange (ETDEWEB)

Seeger, O., E-mail: oliver.seeger@rwth-aachen.de [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Safety of Irradiated Nuclear Materials Unit, Postfach 2340, 76125 Karlsruhe (Germany); Laurie, M., E-mail: mathias.laurie@ec.europa.eu [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Safety of Irradiated Nuclear Materials Unit, Postfach 2340, 76125 Karlsruhe (Germany); Abjani, A. El; Ejton, J.; Boudaud, D.; Freis, D.; Carbol, P.; Rondinella, V.V. [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Safety of Irradiated Nuclear Materials Unit, Postfach 2340, 76125 Karlsruhe (Germany); Fütterer, M. [European Commission, Joint Research Centre (JRC), Institute for Energy and Transport (IET), Nuclear Reactor Integrity Assessment and Knowledge Management Unit, PO Box 2, 1755 ZG Petten (Netherlands); Allelein, H.-J. [Lehrstuhl für Reaktorsicherheit und -technik an der RWTH Aachen, Kackertstraße 9, 52072 Aachen (Germany)

2016-09-15

The Cold Finger Apparatus (KühlFinger-Apparatur—KüFA) in operation at JRC-ITU is designed to experimentally scrutinize the effects of Depressurization LOss of Forced Circulation (D-LOFC) accident scenarios on irradiated High Temperature Reactor (HTR) fuel pebbles. Up to 1600 °C, the reference maximum temperature for these accidents, high-quality German HTR fuel pebbles have already demonstrated a small fission product release. This paper discusses and compares the releases obtained from KüFA-testing the pebbles HFR-K5/3 and HFR-EU1/3, which were both irradiated in the High Flux Reactor (HFR) in Petten. We present the time-dependent fractional release of the volatile fission product {sup 137}Cs as well as the fission gas {sup 85}Kr for both pebbles. For HFR-EU1/3 the isotopes {sup 134}Cs and {sup 154}Eu as well as the shorter-lived {sup 110m}Ag have also been measured. A detailed description of the experimental setup and its accuracy is given. The data for the recently tested pebbles is discussed in the context of previous results.

HTR core physics and transient analyses by the Panthermix code system

Energy Technology Data Exchange (ETDEWEB)

Haas, J.B.M. de; Kuijper, J.C.; Oppe, J. [NRG - Fuels, Actinides and Isotopes group, Petten (Netherlands)

2005-07-01

At NRG Petten, core physics analyses on High Temperature gas-cooled Reactors (HTRs) are mainly performed by means of the PANTHERMIX code system. Since some years NRG is developing the HTR reactor physics code system WIMS/PANTHERMIX, based on the lattice code WIMS (Serco Assurance, UK), the 3-dimensional steady-state and transient core physics code PANTHER (British Energy, UK) and the 2-dimensional R-Z HTR thermal hydraulics code THERMIX-DIREKT (Research Centre FZJ Juelich, Germany). By means of the WIMS code nuclear data are being generated to suit the PANTHER code's neutronics. At NRG the PANTHER code has been interfaced with THERMIX-DIREKT to form PANTHERMIX, to enable core-follow/fuel management and transient analyses in a consistent manner on pebble bed type HTR systems. Also provisions have been made to simulate the flow of pebbles through the core of a pebble bed HTR, according to a given (R-Z) flow pattern. As examples of the versatility of the PANTHERMIX code system, calculations are presented on the PBMR, the South African pebble bed reactor design, to show the transient capabilities, and on a plutonium burning MEDUL-reactor, to demonstrate the core-follow/fuel management capabilities. For the investigated cases a good agreement is observed with the results of other HTR core physics codes.

Why HTR/VHTR? A European point of view

International Nuclear Information System (INIS)

Basini, V.; Bogusch, E.; Breuil, E.; Buckthorpe, D.; Chauvet, V.; Ftitterer, M.; Van Heek, A.; Hittner, D.; Von Lensa, W.; Pirson, J.; Verrier, D.

2008-01-01

The (European) High Temperature Reactor Technology Network (HTR-TN) was created in 2000 by the main industrial and Research actors of nuclear energy in Europe for elaborating a strategy for developing advanced HTR technology towards industrial application and for taking initiatives for implementing this strategy, most particularly through the Euratom funded R and D programmes. HTR-TN members are convinced that the main market push for industrial deployment of a new generation of HTR will not come from utility needs for electricity generation, but from industrial process heat needs: even if HTR can be considered for satisfying particular niches of the electricity market, there will not be any incentive for utilities already experienced in the exploitation of large LWR to take the risk of a significant technology change, when no evident competitive edge would result from it. On the contrary, HTR is the sole nuclear system that can address heat needs of a large number of industrial processes that require a higher temperature than the temperature provided by all other types of industrial reactors. The possibility for HTR to address the industrial process heat market is a strong asset, as it opens to HTR a large market which is presently looking for solutions to reduce drastically CO 2 emissions, but at the same time it is a huge challenge: industrial exploitation of nuclear energy has been for the time being focused on electricity generation for which user requirements are relatively uniform. The versatility of process heat needs in terms of power, temperature, reliability, etc. will require a much larger flexibility of the nuclear heat source, which is not usual for nuclear industry, looking for competitiveness through standardisation. Therefore HTR-TN considers that the top priority innovation for HTR present development should not be missed: it is to demonstrate at an industrial scale the technical, industrial and economical feasibility of the coupling of a HTR with

Neutronic feasibility design of a small long-life HTR

International Nuclear Information System (INIS)

Ding Ming; Kloosterman, Jan Leen

2011-01-01

Highlights: ► We propose the neutronic feasibility design of a small, long lifetime and transportable HTR. ► Comparison of cylindrical, annular and scatter cores of the small block-type HTR. ► The design of the scatter core effectively reduces the number of the fuel block and increases the lifetime and burnup of the reactor. - Abstract: Small high temperature gas-cooled reactors (HTRs) have the advantages of transportability, modular construction and flexible site selection. This paper presents the neutronic feasibility design of a 20 MWth U-Battery, which is a long-life block-type HTR. Key design parameters and possible reactor core configurations of the U-Battery were investigated by SCALE 5.1. The design parameters analyzed include fuel enrichment, the packing fraction of TRISO particles, the radii of fuel compacts and kernels, and the thicknesses of top and bottom reflectors. Possible reactor core configurations investigated include five cylindrical, two annular and four scatter reactor cores for the U-Battery. The neutronic design shows that the 20 MWth U-Battery with a 10-year lifetime is feasible using less than 20% enriched uranium, while the negative values of the temperature coefficients of reactivity partly ensure the inherent safety of the U-Battery. The higher the fuel enrichment and the packing fraction of TRISO particles are, the lower the reactivity swing during 10 years will be. There is an optimum radius of fuel kernels for each value of the fuel compact design parameter (i.e., radius) and a specific fuel lifetime. Moreover, the radius of fuel kernels has a small influence on the infinite multiplication factor of a typical fuel block in the range of 0.2–0.25 mm, when the radius of fuel compacts is 0.6225 cm and the lifetime of the fuel block is 10 years. The comparison of the cylindrical reactor cores with the non-cylindrical ones shows that neutron under-moderation is a basic neutronic characteristic of the reactor core of the U

Software Unit Testing during the Development of Digital Reactor Protection System of HTR-PM

International Nuclear Information System (INIS)

Guo Chao; Xiong Huasheng; Li Duo; Zhou Shuqiao; Li Jianghai

2014-01-01

Reactor Protection System (RPS) of High Temperature Gas-Cooled Reactor - Pebble bed Module (HTR-PM) is the first digital RPS designed and to be operated in the Nuclear Power Plant (NPP) of China, and its development process has receives a lot of concerns around the world. As a 1E-level safety system, the RPS has to be designed and developed following a series of nuclear laws and technical disciplines including software verification and validation (software V&V). Software V&V process demonstrates whether all stages during the software development are performed correctly, completely, accurately, and consistently, and the results of each stage are testable. Software testing is one of the most significant and time-consuming effort during software V&V. In this paper, we give a comprehensive introduction to the software unit testing during the development of RPS in HTR-PM. We first introduce the objective of the testing for our project in the aspects of static testing, black-box testing, and white-box testing. Then the testing techniques, including static testing and dynamic testing, are explained, and the testing strategy we employed is also introduced. We then introduce the principles of three kinds of coverage criteria we used including statement coverage, branch coverage, and the modified condition/decision coverage. As a 1E-level safety software, testing coverage needs to be up to 100% mandatorily. Then we talk the details of safety software testing during software development in HTR-PM, including the organization, methods and tools, testing stages, and testing report. The test result and experiences are shared and finally we draw a conclusion for the unit testing process. The introduction of this paper can contribute to improve the process of unit testing and software development for other digital instrumentation and control systems in NPPs. (author)

Application of grey model on analyzing the passive natural circulation residual heat removal system of HTR-10

Institute of Scientific and Technical Information of China (English)

ZHOU Tao; PENG Changhong; WANG Zenghui; WANG Ruosu

2008-01-01

Using the grey correlation analysis, it can be concluded that the reactor pressure vessel wall temperature has the strongest effect on the passive residual heat removal system in HTR (High Temperature gas-cooled Reactor),the chimney height takes the second place, and the influence of inlet air temperature of the chimney is the least. This conclusion is the same as that analyzed by the traditional method. According to the grey model theory, the GM(1,1) and GM(1, 3) model are built based on the inlet air temperature of chimney, pressure vessel temperature and the chimney height. Then the effect of three factors on the heat removal power is studied in this paper. The model plays an important role on data prediction, and is a new method for studying the heat removal power. The method can provide a new theoretical analysis to the passive residual heat removal system of HTR.

Gamma dose rate estimation and operation management suggestions for decommissioning the reactor pressure vessel of HTR-PM

Energy Technology Data Exchange (ETDEWEB)

Sheng Fang; Hong Li; Jianzhu Cao; Wenqian Li; Feng Xie; Jiejuan Tong [Institute of Nuclear and New Energy Technology, Tsinghua, University, Beijing (China)

2013-07-01

China is now designing and constructing a high temperature gas cooled reactor-pebble bed module (HTR-PM). In order to investigate the future decommissioning approach and evaluate possible radiation dose, gamma dose rate near the reactor pressure vessel was calculated for different cooling durations using QAD-CGA program. The source term of this calculation was provided by KORIGEN program. Based on the calculated results, the spatial distribution and temporal changes of gamma dose rate near reactor pressure vessel was systematically analyzed. A suggestion on planning decommissioning operation of reactor pressure vessel of HTRPM was given based on calculated dose rate and the Chinese Standard GB18871-2002. (authors)

EC-funded project (HTR-L) for the definition of a European safety approach for HTR's

International Nuclear Information System (INIS)

Ehster, S.; Dominguez, M.T.; Coe, I.; Brinkmann, G.; Lensa, W. von; Mheen, W. van der; Alessandroni, C.; Pirson, J.

2002-01-01

The inherent safety features of the HTRs make events leading to severe core damage highly unlikely and constitute the main differentiating aspects compared to LWRs. While a known and stable regulatory environment has long been established for Light Water Reactors, a different approach is necessary for the licensing of HTR based power plants. Among the R and D projects funded by the European Commission for HTR reactors, the HTR-L project is dedicated to the definition of a common and coherent European safety approach and the identification of the main licensing issues for the licensing framework of the Modular HTRs. Other specific objectives of this project are : To develop a methodology to classify the accidental conditions; To define the preliminary requirements for the confinement of radioactive products and to assess the need for a 'conventional' containment structure; To establish a SSC (2) classification and to define the rules for equipment qualification; To identify the key issues that need to be addressed in the licensing process of the HTRs; To organize a workshop with the concerned Safety Authorities at the end of the project. This paper will explain the project objectives and its final expected outcomes. (author)

HTR-Proteus Pebble Bed Experimental Program Cores 5,6,7,&8: Columnar Hexagonal Point-on-Point Packing with a 1:2 Moderator-to-Fuel Pebble Ratio

Energy Technology Data Exchange (ETDEWEB)

Bess, John D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sterbentz, James W. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Snoj, Luka [Idaho National Lab. (INL), Idaho Falls, ID (United States); Lengar, Igor [Idaho National Lab. (INL), Idaho Falls, ID (United States); Koberl, Oliver [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-03-01

PROTEUS is a zero-power research reactor based on a cylindrical graphite annulus with a central cylindrical cavity. The graphite annulus remains basically the same for all experimental programs, but the contents of the central cavity are changed according to the type of reactor being investigated. Through most of its service history, PROTEUS has represented light-water reactors, but from 1992 to 1996 PROTEUS was configured as a pebble-bed reactor (PBR) critical facility and designated as HTR-PROTEUS. The nomenclature was used to indicate that this series consisted of High Temperature Reactor experiments performed in the PROTEUS assembly. During this period, seventeen critical configurations were assembled and various reactor physics experiments were conducted. These experiments included measurements of criticality, differential and integral control rod and safety rod worths, kinetics, reaction rates, water ingress effects, and small sample reactivity effects (Ref. 3). HTR-PROTEUS was constructed, and the experimental program was conducted, for the purpose of providing experimental benchmark data for assessment of reactor physics computer codes. Considerable effort was devoted to benchmark calculations as a part of the HTR-PROTEUS program. References 1 and 2 provide detailed data for use in constructing models for codes to be assessed. Reference 3 is a comprehensive summary of the HTR-PROTEUS experiments and the associated benchmark program. This document draws freely from these references. Only Cores 9 and 10 are evaluated in this benchmark report due to similarities in their construction. The other core configurations of the HTR-PROTEUS program are evaluated in their respective reports as outlined in Section 1.0. Cores 9 and 10 were evaluated and determined to be acceptable benchmark experiments.

HTR-PROTEUS PEBBLE BED EXPERIMENTAL PROGRAM CORES 5, 6, 7, & 8: COLUMNAR HEXAGONAL POINT-ON-POINT PACKING WITH A 1:2 MODERATOR-TO-FUEL PEBBLE RATIO

Energy Technology Data Exchange (ETDEWEB)

John D. Bess

2013-03-01

PROTEUS is a zero-power research reactor based on a cylindrical graphite annulus with a central cylindrical cavity. The graphite annulus remains basically the same for all experimental programs, but the contents of the central cavity are changed according to the type of reactor being investigated. Through most of its service history, PROTEUS has represented light-water reactors, but from 1992 to 1996 PROTEUS was configured as a pebble-bed reactor (PBR) critical facility and designated as HTR-PROTEUS. The nomenclature was used to indicate that this series consisted of High Temperature Reactor experiments performed in the PROTEUS assembly. During this period, seventeen critical configurations were assembled and various reactor physics experiments were conducted. These experiments included measurements of criticality, differential and integral control rod and safety rod worths, kinetics, reaction rates, water ingress effects, and small sample reactivity effects (Ref. 3). HTR-PROTEUS was constructed, and the experimental program was conducted, for the purpose of providing experimental benchmark data for assessment of reactor physics computer codes. Considerable effort was devoted to benchmark calculations as a part of the HTR-PROTEUS program. References 1 and 2 provide detailed data for use in constructing models for codes to be assessed. Reference 3 is a comprehensive summary of the HTR-PROTEUS experiments and the associated benchmark program. This document draws freely from these references. Only Cores 9 and 10 are evaluated in this benchmark report due to similarities in their construction. The other core configurations of the HTR-PROTEUS program are evaluated in their respective reports as outlined in Section 1.0. Cores 9 and 10 were evaluated and determined to be acceptable benchmark experiments.

HTR-PM Progress and Further Commercial Deployment

International Nuclear Information System (INIS)

Wu, Frank

2017-01-01

Project Milestones: • 2004: industry investment agreement was signed • 2006: decided to use 2×250 MWt reactor modules with a 200 MWe steam turbine, became a key government R&D project • 2008: ATP was issued • 2012.12.9: FCD the first concrete poured. Chinese HTR development: HTR Roles in China - Power generation: supplement to LWR; repowering coal fired plants - Co-generation to supply steam - Hydrogen production

Computational fluid dynamic model for thermohydraulic calculation for the steady-state of the real scale HTR-1

Energy Technology Data Exchange (ETDEWEB)

Gamez, Abel; Rojas, Leorlen; Rosales, Jesus; Castro, Landy Y.; Gonzalez, Daniel; Garcia, Carlos, E-mail: agamezgmf@gmail.com, E-mail: leored1984@gmail.com, E-mail: jrosales@instec.cu, E-mail: lcastro@instec.cu, E-mail: danielgonro@gmail.com, E-mail: cgr@instec.cu [Instituto Superior de Tecnologias y Ciencias Aplicadas (InSTEC), La Habana (Cuba); Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil); Oliveira, Carlos B. de, E-mail: cabol@ufpe.br [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil); Dominguez, Dany S., E-mail: dsdominguez@gmail.com [Universidade Estadual de Santa Cruz (UESC), Ilheus, BA (Brazil)

2015-07-01

The high temperature gas cooled reactor (HTGR) is one of candidates of next generation of nuclear reactor according to IAEA report 2013. Evaluation of thermohydraulic performance and an experimental comparison results were proposed to the international research community. In this article, the tree dimensional CFD thermohydraulic modelation of steady state of HTR-10 modular reactor, using ANSYS CFX v14.0, has been done. Code-to-code and Code-to-experiment benchmark analyses, related to the testing program of the HTR-10 plant including steady state temperature distribution with the reactor at full power, were developed. The 3D real scale representation of reflector zone and fluid path flow inner and outer reflector blocks and cold helium cavity were carried out. The porous medium model was used to simulate the core zone in the reactor. The power distribution of the initial core published by IAEA-TECDOC-1694 obtained by Chief Scientific Investigators (CSIs) from China was used as heat sources in the core zone. (author)

Design on Hygrometry System of Primary Coolant Circuit of HTR-PM

International Nuclear Information System (INIS)

Sun Yanfei; Zhong Shuoping; Huang Xiaojin

2014-01-01

Helium is the primary coolant in HTR-PM. If vapor get into the helium in primary coolant circuit because of some special reasons, such as the broken of steam-generator tube, chemical reaction will take effect between the graphite in reactor core and vapor in primary coolant circuit, and the safety of the reactor operation will be influenced. So the humidity of the helium in primary coolant circuit is one key parameter of HTR-PM to be monitored in-line. Once the humidity is too high, trigger signal of turning off the reactor must be issued. The hygrometry system of HTR-PM is consisting of filter, cooler, hygrometry sensor, flow meter, and some valves and tube. Helium with temperature of 250℃ is lead into the hygrometry system from the outlet of the main helium blower. After measuring, the helium is re-injected back to the primary circuit. No helium loses in this processing, and no other pump is needed. Key factors and calculations in design on hygrometry system of HTR-PM are described. A sample instrument has been made. Results of experiments proves that this hygrometry system is suitable for monitoring the humidity of the primary coolant of HTR-PM. (author)

Studi Awal Desain Pebble Bed Reactor Berbasis Htr-pm Dengan Skema Resirkulasi Bahan Bakar Once-through-then-out

OpenAIRE

Setiadipura, Topan; Pane, Jupiter Sitorus; Zuhair, Zuhair

2016-01-01

STUDI AWAL DESAIN PEBBLE BED REACTOR BERBASIS HTR-PM DENGAN RESIRKULASI BAHAN BAKAR ONCE-THROUGH-THEN-OUT. Reaktor nuklir tipe pebble bed reactor (PBR) adalah salah satu reaktor canggih dengan fitur keselamatan pasif yang kuat. Pada desain tipe ini berpotensi untuk dilakukan kogenerasi yang bermanfaat untuk pengolahan berbagai mineral di berbagai pulau di Indonesia. Operasi PBR dapat lebih disederhanakan dengan menerapkan skema pengisian bahan bakar once-through-then-out (OTTO) dimana bahan b...

The physics design of the HTR-1160

International Nuclear Information System (INIS)

Huebner, A.; Brandes, S.

1975-01-01

This paper describes the physica design of the reactor core of the helium cooled, graphite moderated high-temperature reactor HTR-1160. A discussion is given of the design criteria, the calculational methods, the burnup cycle, the power distribution and the reactivity control. (orig.) [de

Research on dynamics and experiments about auxiliary bearings for the helium circulator of the 10 MW high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Zhao, Yulan; Yang, Guojun; Liu, Xingnan; Shi, Zhengang; Zhao, Lei

2016-01-01

Highlights: • The research in this paper is based on the AMB helium circulator of HTR-10. • The dynamic rotor performance is analyzed by processing experimental data. • The mechanical bearing without lubrication can be applied in the HTR-10 system. - Abstract: The 10 MW high-temperature gas-cooled reactor (HTR-10) was constructed by the Institute of Nuclear and New Energy Technology (INET) of Tsinghua University. The auxiliary bearing is utilized in this system to meet particular requirements for the reactor. The main role of the auxiliary bearing is to constrain rotor displacements and also to support the rotor when the rotor drops down, which is caused by the active magnetic bearing (AMB) failure. The auxiliary bearing needs to endure huge impact, rapid angular acceleration and thermal shock. On the one hand, complex geometrical constructions and forces applied on the system bring difficulties and restrictions to establish an appropriate model to reveal the actual dynamic process. On the other hand, large volumes of data obtained from experiments show velocities and displacements of the rotor during the rotor drop process and then can indicate the actual dynamic interactions to a great extent. The research in this paper is based on the test rig of the AMB helium circulator of HTR-10. This paper aims to analyze the dynamic performance and contact forces of the rotor by processing experimental data. A measurement to estimate forces developed due to impacts of the rotor and the auxiliary bearings is presented. It is of great significance and provides certain foundation to elaborate the rotor drop process for the AMB helium circulator of HTR-10.

HTR Plans in Poland

International Nuclear Information System (INIS)

Sobolewski, Józef

2017-01-01

Target for HTR: Polish Heat Market: Today 100% heat market is dominated by fossil fuels; mostly coal in district heating and coal and gas in industry heat generation. Huge potential for nuclear reactors Currently can be addressed only in terms of LWR, i.e. T <250 ° C, useful in district heating, but not in industry. Need for new technologies •HTGR (High Temperature Gas Reactor) ~600°C, e.g. for industry steam generation. •VHTR (Very High Temperature Reactor), ... ~1000°C, e.g. for hydrogen production

Study on computer-aided control system design platform of 10MW high temperature gas-cooled test reactor

International Nuclear Information System (INIS)

Feng Yan; Shi Lei; Sun Yuliang; Luo Shaojie

2004-01-01

the 10 MW high temperature gas-cooled test reactor (HTR-10) is the first modular pebble bed reactor built in China, which needs to be researched on engineering design, control study, safety analysis and operator training. An integrated system for simulation, control design and online assistance of the HTR-10 (HTRSIMU) has been developed by the Institute of Nuclear Energy Technology (INET) of Tsinghua University. The HTRSIMU system is based on a high-speed local area network, on which a computer-aided control system design platform (CDP) is developed and combined with the simulating subsystem in order to provide a visualized and convenient tool for the HTR-10 control system design. The CDP has friendly man-machine interface and good expansibility, in which eighteen types of control items are integrated. These control items are divided into two types: linear and non-linear control items. The linear control items include Proportion, Integral, Differential, Inertial, Leed-lag, Oscillation, Pure-lag, Common, PID and Fuzzy, while the non-linear control items include Saturation, Subsection, Insensitive, Backlash, Relay, Insensi-Relay, Sluggish-Relay and Insens-Slug. The CDP provides a visualized platform for control system modeling and the control loop system can be automatically generated and graphically simulated. Users can conveniently design control loop, modify control parameters, study control method, and analyze control results just by clicking mouse buttons. This kind of control system design method can provide a powerful tool and good reference for the actual system operation for HTR-10. A control scheme is also given and studied to demonstrate the functions of the CDP in this article. (author)

AREVA HTR concept for near-term deployment

Energy Technology Data Exchange (ETDEWEB)

Lommers, L.J., E-mail: lewis.lommers@areva.com [AREVA Inc., 2101 Horn Rapids Road, Richland, WA 99354 (United States); Shahrokhi, F. [AREVA Inc., Lynchburg, VA (United States); Mayer, J.A. [AREVA Inc., Marlborough, MA (United States); Southworth, F.H. [AREVA Inc., Lynchburg, VA (United States)

2012-10-15

This paper introduces AREVA's High Temperature Reactor (HTR) steam cycle concept for near-term industrial deployment. Today, nuclear power primarily impacts only electricity generation. The process heat and transportation fuel sectors are completely dependent on fossil fuels. In order to impact this energy sector as rapidly as possible, AREVA has focused its HTR development effort on the steam cycle HTR concept. This reduces near-term development risk and minimizes the delay before a useful contribution to this sector of the energy economy can be realized. It also provides a stepping stone to longer term very high temperature concepts which might serve additional markets. A general description of the current AREVA steam cycle HTR concept is provided. This concept provides a flexible system capable of serving a variety of process heat and cogeneration markets in the near-term.

AREVA HTR concept for near-term deployment

International Nuclear Information System (INIS)

Lommers, L.J.; Shahrokhi, F.; Mayer, J.A.; Southworth, F.H.

2012-01-01

This paper introduces AREVA's High Temperature Reactor (HTR) steam cycle concept for near-term industrial deployment. Today, nuclear power primarily impacts only electricity generation. The process heat and transportation fuel sectors are completely dependent on fossil fuels. In order to impact this energy sector as rapidly as possible, AREVA has focused its HTR development effort on the steam cycle HTR concept. This reduces near-term development risk and minimizes the delay before a useful contribution to this sector of the energy economy can be realized. It also provides a stepping stone to longer term very high temperature concepts which might serve additional markets. A general description of the current AREVA steam cycle HTR concept is provided. This concept provides a flexible system capable of serving a variety of process heat and cogeneration markets in the near-term.

The Research Status for Decommissioning and Radioactive Waste Minimization of HTR-PM

International Nuclear Information System (INIS)

Li Wenqian; Li Hong; Cao Jianzhu; Tong Jiejuan

2014-01-01

Decommissioning of the high-temperature gas-cooled reactor-pebble bed module (HTR-PM) as a part of the nuclear power plant, is very important during the early design stage of the construction, and it is under study and research currently. This article gives a thorough description of the current decommissioning study status of HTR-PM. Since HTR-PM has its features such as adopting a large amount of graphite, the waste inventory and characterization will be quite different from other type of reactors, new researches should be carried out and good lessons of practices and experiences should be learned from international other reactors, especially the AVR. Based on the new international regulations and Chinese laws, a comprehensive decommissioning program should be proposed to guarantee the HTR-PM will succeed in every stage of the decommissioning, such as defueling, decontamination, dismantling, demolition, waste classification and disposal, etc. In the meantime, the minimization of the radioactive waste should be taken into account during the whole process - before construction, during operation and after shut down. In this article, the decommissioning strategy and program conception of HTR-PM will be introduced, the radiation protection consideration during the decommissioning activities will be discussed, and the research on the activation problem of the decommissioning graphite will be introduced. (author)

Utilization of heat from High Temperature Reactors (HTR) for dry reforming of methane

Science.gov (United States)

Jastrząb, Krzysztof

2018-01-01

One of the methods for utilization of waste carbon dioxide consists in reaction of methane with carbon dioxide, referred to as dry reforming of methane. It is an intensely endothermic catalytic process that takes place at the temperature above 700°C. Reaction of methane with carbon dioxide leads to formation of synthesis gas (syngas) that is a valuable chemical raw material. The energy that is necessary for the process to take place can be sourced from High Temperature Nuclear Reactors (HTR). The completed studies comprises a series of thermodynamic calculations and made it possible to establish optimum conditions for the process and demand for energy from HTR units. The dry reforming of methane needs also a catalytic agent with appropriate activity, therefore the hydrotalcite catalyser with admixture of cerium and nickel, developed at AGH University of Technology seems to be a promising solution. Thus, the researchers from the Institute for Chemical Processing of Coal (IChPW) in Zabrze have developed a methodology for production of the powdery hydrotalcite catalyser and investigated catalytic properties of the granulate obtained. The completed experiments confirmed that the new catalyser demonstrated high activity and is suitable for the process of methane dry reforming. In addition, optimum parameters of the were process (800°C, CO2:CH4 = 3:1) were established as well. Implementation of the technology in question into industrial practice, combined with utilization of HTR heat can be a promising method for management of waste carbon dioxide and may eventually lead to mitigation of the greenhouse effect.

Overview of Japanese seismic research program for HTR

International Nuclear Information System (INIS)

Ikushima, T.

1978-01-01

In order to obtain the license for construction and operation of HTR developed in and/or introduced into Japan, it is necessary to insure the integrity of reactor structures and the capability of reactor shutdown and the maintenance of safety shutdown for the seismic design condition. Because Japan is located in relatively high seismicity zone, even when an excessive earthquake would occur, the public and plant personnel should be protected from radiation hazard. The report describes the following: (1) present status of development and construction plan of HTR, (2) guideline of aseismic design, (3) need of aseismic research, (4) present status of research and development, and (5) future plans

Status of development of gas-cooled reactors in Switzerland, 1987

International Nuclear Information System (INIS)

Helbling, W.; Sarlos, G.

1988-01-01

Swiss industrial companies and the Federal Institute for Reactor Research are involved in the framework of German-Swiss cooperation in the HTR-500 project. Another effort in Switzerland is directed to the development of a small heating reactor, in the power range of 10 to 50 MW, for district heating, one of the concepts investigated being an HTR pebble-bed reactor

An HTR cogeneration system for industrial applications

International Nuclear Information System (INIS)

Haverkate, B.R.W.; Heek, A.I. van; Kikstra, J.F.

2001-01-01

Because of its favourable characteristics of safety and simplicity the high-temperature reactor (HTR) could become a competitive heat source for a cogeneration unit. The Netherlands is a world leading country in the field of cogeneration. As nuclear energy remains an option for the medium and long term in this country, systems for nuclear cogeneration should be explored and developed. Hence, ECN Nuclear Research is developing a conceptual design of an HTR for Combined generation of Heat and Power (CHP) for the industry in and outside the Netherlands. The design of this small CHP-unit for industrial applications is mainly based on a pre-feasibility study in 1996, performed by a joint working group of five Dutch organisations, in which technical feasibility was shown. The concept that was subject of this study, INCOGEN, used a 40 MW thermal pebble bed HTR and produced a maximum amount of electricity plus low temperature heat. The system has been improved to produce industrial quality heat, and has been renamed ACACIA. The output of this installation is 14 MW electricity and 17 tonnes of steam per hour, with a pressure of 10 bar and a temperature of 220 deg. C. The economic characteristics of this installation turned out to be much more favourable using modern data. The research work for this installation is embedded in a programme that has links to the major HTR projects in the world. Accordingly ECN participates in several IAEA Co-ordinated Research Programmes (CRPs). Besides this, ECN is involved in the South African PBMR-project. Finally, ECN participates in the European Concerted Action on Innovative HTR. (author)

Development of a Reliable Fuel Depletion Methodology for the HTR-10 Spent Fuel Analysis

Energy Technology Data Exchange (ETDEWEB)

Chung, Kiwhan [Los Alamos National Laboratory; Beddingfield, David H. [Los Alamos National Laboratory; Geist, William H. [Los Alamos National Laboratory; Lee, Sang-Yoon [unaffiliated

2012-07-03

A technical working group formed in 2007 between NNSA and CAEA to develop a reliable fuel depletion method for HTR-10 based on MCNPX and to analyze the isotopic inventory and radiation source terms of the HTR-10 spent fuel. Conclusions of this presentation are: (1) Established a fuel depletion methodology and demonstrated its safeguards application; (2) Proliferation resistant at high discharge burnup ({approx}80 GWD/MtHM) - Unfavorable isotopics, high number of pebbles needed, harder to reprocess pebbles; (3) SF should remain under safeguards comparable to that of LWR; and (4) Diversion scenarios not considered, but can be performed.

Benchmark calculation for the steady-state temperature distribution of the HTR-10 under full-power operation

International Nuclear Information System (INIS)

Chen Fubing; Dong Yujie; Zheng Yanhua; Shi Lei; Zhang Zuoyi

2009-01-01

Within the framework of a Coordinated Research Project on Evaluation of High Temperature Gas-Cooled Reactor Performance (CRP-5) initiated by the International Atomic Energy Agency (IAEA), the calculation of steady-state temperature distribution of the 10 MW High Temperature Gas-Cooled Reactor-Test Module (HTR-10) under its initial full power experimental operation has been defined as one of the benchmark problems. This paper gives the investigation results obtained by different countries who participate in solving this benchmark problem. The validation works of the THERMIX code used by the Institute of Nuclear and New Energy Technology (INET) are also presented. For the benchmark items defined in this CRP, various calculation results correspond well with each other and basically agree the experimental results. Discrepancies existing among various code results are preliminarily attributed to different methods, models, material properties, and so on used in the computations. Temperatures calculated by THERMIX for the measuring points in the reactor internals agree well with the experimental values. The maximum fuel center temperatures calculated by the participants are much lower than the limited value of 1,230degC. According to the comparison results of code-to-code as well as code-to-experiment, THERMIX is considered to reproduce relatively satisfactory results for the CRP-5 benchmark problem. (author)

The challenge of introducing HTR plants on to the international power plant market

International Nuclear Information System (INIS)

Bogen, J.; Stoelzl, D.

1987-01-01

The international power plant market today is characterized by high increase in energy consumption for developing countries with limitations of investment capital and low increase in energy consumption for industrialized countries with limitations of additional power plant capacities. As a consequence there is a low demand for large new power stations. This leads to a tendency for small and medium sized power plant units - meeting high environmental standards - for which the total investment volume is low and full load operation of a plant can be realized earlier due to the small block capacity. - For nuclear power plants the High-Temperature-Reactor (HTR)-line with spherical fuel elements and a core structure of graphite is specially suited for this small and medium sized nuclear reactor (SMSNR) capacity. The excellent safety characteristics, the high availability, the low radiation doses for the operation personnel and the environment of the HTR line has been demonstrated by 20 years of operation of the AVR-15 MWe experimental power plant in Juelich F.R.G. and since 1985 by operation of the THTR-300 MWe prototype plant at Hamm-Uentrop F.R.G. Up-dated concepts of the HTR-line are under design for electricity generation (HTR-500), for co-generation of power and heat (HTR-100) and for district heating purposes only (GHR-10). By implementing two HTR projects the Brown Boveri Group is in the position to realize the collected experiences from design, licensing, erection, commissioning and operation for the follow-on projects. This leads to practical and sound technical solutions convenient for existing manufacturing processes, well known materials, standardized components and usual manufacturing tolerances. Specific plant characteristics can be used for advantages in the competition. (author)

Actual characteristics study on HTR-10GT coupling with direct gas turbine cycle

International Nuclear Information System (INIS)

Peng Xuechuang; Zhu Shutang; Wang Jie

2005-01-01

Compared with a plant of steam turbine cycle, a HTGR plant with direct gas turbine cycle has a higher thermal efficiency. A lot of investigations on the characteristics of HTR-10GT, which is the reactor studying project of Tsinghua University, have been carried out, however, all of them are based on the theoretical Brayton Cycle which neglects many actual conditions, such as leakage, pressure loss and so on. For engineering practices, leakage is an unavoidable problem. The difference of the location and capacity of leakage will directly influence the working medium's thermoparameters and lead to fall of the cycle efficiency. The present study is focused on the performance of an actual Brayton cycle with practical conditions of leakage. The present study which based on building the physical and mathematical model of the leakage, aims to study the actual characteristics of the direct gas turbine circle. (authors)

An HTR cogeneration system for industrial application

International Nuclear Information System (INIS)

Haverkate, B.R.W.; Van Heek, A.I.; Kikstra, J.F.

1999-01-01

Because of its favourable characteristics of safety and simplicity the high-temperature reactor (HTR) could become a competitive heat source for a cogeneration unit. The Netherlands is a world leading country in the field of cogeneration. As nuclear energy remains an option for the medium and long term in this country, systems for nuclear cogeneration should be explored and developed. Hence, ECN Nuclear Research is developing a conceptual design of an HTR for Combined generation of Heat and Power (CHP) for the industry in and outside the Netherlands. The design of this small CHP-unit for industrial applications is mainly based on a pre-feasibility study in 1996, performed by a joint working group of five Dutch organisations, in which technical feasibility was shown. The concept that was subject of that study, INCOGEN, used a 40 MW thermal pebble bed HTR and produced a maximum amount of electricity plus low temperature heat. The system has been improved to produce industrial quality heat, and has been renamed ACACIA. The output of this installation is 14 MW electricity and 17 tonnes of steam per hour, with a pressure of 10 bar and a temperature of 220C. The economic characteristics of this installation turned out to be much more favourable using modern cost data. 15 refs

IRPhE-HTR-ARCH-01, Archive of HTR Primary Documents

International Nuclear Information System (INIS)

2004-01-01

Description: High Temperature Reactor Studies, including experiments in critical facilities or in prototypes have been carried out in the past. Information gathered, experience gained and experimental data produced are of value for the development of future advanced HTRs. For the purpose of knowledge, competence, information preservation and management, computer readable archives have been established. The present archive includes several relevant documents relative to the following: - Graphite Moderated Critical Facility, CESAR at Cadarache. Dragon Countries Physics Meetings (DCPM); - OTTO Pebble Bed Reactors; - Gulf - HTGR Experiments; - Zero Power MARIUS Reactor; - Pebble-bed KAHTER Critical Facility; - Helium Cooled Fast Reactor Assessment Studies; - Gas Cooled Reactor Technology Safety and Siting; - Initial Evaluation of the Gas-Turbine Modules HTGCR; - A report on Nuclear Graphite; - AVR Reactor Juelich (new in version 02); - HTR IAEA proceedings (new in version 02); - Studies at IRI Delft(new in version 02); - Studies and experiments at PSI Villigen (new in version 02); 2 - Related or auxiliary information: IRPHE-DRAGON-DPR, high Temperature Reactor Dragon Project, Primary Documents NEA-1726/01. 3 - Software requirements: Acrobat Reader, Microsoft Word, HTML Browser required

Programmes and projects for high-temperature reactor development

International Nuclear Information System (INIS)

Bogusch, Edgar; Hittner, Dominique

2009-01-01

An increasing attention has to be recognised worldwide on the development of High-Temperature Reactors (HTR) which has started in Germany and other countries in the 1970ies. While pebble bed reactors with spherical fuel elements have been developed and constructed in Germany, countries such as France, the US and Russia investigated HTR concepts with prismatic block-type fuel elements. The concept of a modular HTR formerly developed by Areva NP was an essential basis for the HTR-10 in China. A pebble bed HTR for electricity production is developed in South Africa. The construction is planned after the completion of the licensing procedure. Also the US is planning an HTR under the NGNP (Next Generation Nuclear Plant) Project. Due to the high temperature level of the helium coolant, the HTR can be used not only for electricity production but also for supply of process heat. Including its inherent safety features the HTR is an attractive candidate for heat supply to various types of plants e.g. for hydrogen production or coal liquefactions. The conceptual design of an HTR with prismatic fuel elements for the cogeneration of electricity and process heat has been developed by Areva NP. On the European scale the HTR development is promoted by the RAPHAEL (ReActor for Process heat, Hydrogen And ELectricity generation) project. RAPHAEL is an Integrated Project of the Euratom 6th Framework Programme for the development of technologies towards a Very High-Temperature Reactor (VHTR) for the production of electricity and heat. It is financed jointly by the European Commission and the partners of the HTR Technology Network (HTR-TN) and coordinated by Areva NP. The RAPHAEL project not only promotes HTR development but also the cooperation with other European projects such as the material programme EXTREMAT. Furthermore HTR technology is investigated in the frame of Generation IV International Forum (GIF). The development of a VHTR with helium temperatures above 900 C for the

Gas cooled thermal reactors with high temperatures (VHTR)

International Nuclear Information System (INIS)

Bouchter, J.C.; Dufour, P.; Guidez, J.; Latge, C.; Renault, C.; Rimpault, G.; Vasile, A.

2014-01-01

VHTR is one of the 6 concepts retained for the 4. generation of nuclear reactors, it is an upgraded version of the HTR-type reactor (High Temperature Reactors). 5 HTR reactors were operated in the world in the eighties, now 2 experimental HTR are working in China and Japan and 2 HTR with an output power of 100 MWe are being built in China. The purpose of the VHTR is to provide an helium at very high temperatures around 1000 Celsius degrees that could be used directly in a thermochemical way to produce hydrogen for instance. HTR reactors are interesting in terms of safety but it does not optimise the consumption of uranium and the production of wastes. This article presents a brief historical account of HTR-type reactors and their main design and safety features. The possibility of using HTR to burn plutonium is also presented as well as the possibility of closing the fuel cycle and of using thorium-uranium fuel. (A.C.)

A 350 MW HTR with an annular pebble bed core

International Nuclear Information System (INIS)

Wang Dazhong; Jiang Zhiqiang; Gao Zuying; Xu Yuanhui

1992-12-01

A conceptual design of HTR-module with an annular pebble bed core was proposed. This design can increase the unit power capacity of HTR-Module from 200 MWt to 350 MWt while it can keep the inherent safety characteristics of modular reactor. The preliminary safety analysis results for 350 MW HTR are given. In order to solve the problem of uneven helium outlet temperature distribution a gas flow mixing structure at bottom of core was designed. The experiment results of a gas mixing simulation test rig show that the mixing function can satisfy the design requirements

HTR fuel development for advanced application

International Nuclear Information System (INIS)

Nickel, H.; Balthesen, E.; Graham, L.W.; Hick, H.

1975-01-01

The advantages of the HTR for nuclear steam supply systems are briefly outlined. Due to its great design flexibility a number of different designs have evolved and the main characteristics of existing experimental prototype and power reactor HTR designs are summarized. The present state of coated particle fuel, particularly with regard to performance, is considered. Some implications of producing higher temperatures are discussed. Finally some of the developments in progress such as minimising the temperature drop between fuel and coolant, and of improving fuel performance by better fission product retention, better chemical stability, and the use of alternative coated materials, are discussed. (U.K.)

Final Report on Utilization of TRU TRISO Fuel as Applied to HTR Systems Part I: Pebble Bed Reactors

Energy Technology Data Exchange (ETDEWEB)

Brian Boer; Abderrafi M. Ougouag

2011-03-01

significant failure is to be expected for the reference fuel particle during normal operation. It was found, however, that the sensitivity of the coating stress to the CO production in the kernel was large. The CO production is expected to be higher in DB fuel than in UO2 fuel, but its exact level has a high uncertainty. Furthermore, in the fuel performance analysis transient conditions were not yet taken into account. The effort of this task in FY 2010 has focused on the optimization of the core to maximize the pebble discharge burnup level, while retaining its inherent safety characteristics. Using generic pebble bed reactor cores, this task will perform physics calculations to evaluate the capabilities of the pebble bed reactor to perform utilization and destruction of LWR used-fuel transuranics. The task will use established benchmarked models, and will introduce modeling advancements appropriate to the nature of the fuel considered (high transuranic [TRU] content and high burn-up). Accomplishments of this work include: •Core analysis of a HTR-MODULE design loaded with Deep-Burn fuel. •Core analysis of a HTR-MODULE design loaded with Deep-Burn fuel and Uranium. •Core analysis of a HTR-MODULE design loaded with Deep-Burn fuel and Modified Open Cycle Components. •Core analysis of a HTR-MODULE design loaded with Deep-Burn fuel and Americium targets.

Final Report on Utilization of TRU TRISO Fuel as Applied to HTR Systems Part I: Pebble Bed Reactors

International Nuclear Information System (INIS)

Boer, Brian; Ougouag, Abderrafi M.

2011-01-01

failure is to be expected for the reference fuel particle during normal operation. It was found, however, that the sensitivity of the coating stress to the CO production in the kernel was large. The CO production is expected to be higher in DB fuel than in UO2 fuel, but its exact level has a high uncertainty. Furthermore, in the fuel performance analysis transient conditions were not yet taken into account. The effort of this task in FY 2010 has focused on the optimization of the core to maximize the pebble discharge burnup level, while retaining its inherent safety characteristics. Using generic pebble bed reactor cores, this task will perform physics calculations to evaluate the capabilities of the pebble bed reactor to perform utilization and destruction of LWR used-fuel transuranics. The task will use established benchmarked models, and will introduce modeling advancements appropriate to the nature of the fuel considered (high transuranic (TRU) content and high burn-up). Accomplishments of this work include: (1) Core analysis of a HTR-MODULE design loaded with Deep-Burn fuel. (2) Core analysis of a HTR-MODULE design loaded with Deep-Burn fuel and Uranium. (3) Core analysis of a HTR-MODULE design loaded with Deep-Burn fuel and Modified Open Cycle Components. (4) Core analysis of a HTR-MODULE design loaded with Deep-Burn fuel and Americium targets.

Assignment of the 5HT7 receptor gene (HTR7) to chromosome 10q and exclusion of genetic linkage with Tourette syndrome

Energy Technology Data Exchange (ETDEWEB)

Gelernter, J.; Rao, P.A.; Pauls, D.L. [Yale Univ. School of Medicine, West Haven, CT (United States)] [and others

1995-03-20

A novel serotonin receptor designated 5HT7 (genetic locus HTR7) was cloned in 1993. This receptor has interesting properties related to ligand affinity and CNS distribution that render HTR7 a very interesting candidate gene for neuropsychiatric disorders. We mapped this gene, first by physical methods and then by genetic linkage. First, we made a tentative assignment to chromosome 10, based on hybridization of an HTR7 probe to a Southern blot of DNA from somatic cell hybrids. We then identified a genetic polymorphism at the HTR7 locus. We identified one extended pedigree where the polymorphism segregated. Using the LEPED computer program for pairwise linkage analysis, we confirmed the assignment of the gene to chromosome 10, specifically 10q21-q24, based on a lod score of 5.37 at 0% recombination between HTR7 and D10S20 (a chromosome 10 reference marker). Finally, we excluded genetic linkage between this locus and Tourette syndrome under a reasonable set of assumptions. 15 refs., 1 fig., 1 tab.

Preliminary ripple effect analysis for HTR 350MWt 4 modules construction

Energy Technology Data Exchange (ETDEWEB)

Lee, T. H.; Lee, K. Y.; Shin, Y. J. [KAERI, Daejeon (Korea, Republic of)

2016-05-15

We propose quantitative analysis techniques for ripple effects such as the production inducement effect and employment inducement effect for HTR 350MWt x 4 module construction and operation ripple effect based on NOAK. It is known that APR1400 reactors export ripple effect is about 8,500 billion KRW. As a result, HTR construction has more effective effect than that of APR1400.

Concept of a HTR modular plant for generation of process heat in a chemical plant

International Nuclear Information System (INIS)

1991-07-01

This final report summarizes the results of a preliminary study on behalf of Buna AG and Leunawerke AG. With regard to the individual situations the study investigated the conditions for modular HTR-2 reactors to cover on-site process heat and electric power demands. HTR-2 reactor erection and operation were analyzed for their economic efficiency compared with fossil-fuel power plants. Considering the prospective product lines, the technical and economic conditions were developed in close cooperation with Buna AG and Leunawerke AG. The study focused on the technical integration of modular HTR reactors into plants with regard to safety concepts, on planning, acceptance and erection concepts which largely exclude uncalculable scheduling and financial risks, and on comparative economic analyses with regard to fossil-fuel power plants. (orig.) [de

The market potential of HTR modular reactors as a heat source for high - temperature processes in the Federal Republic of Germany

International Nuclear Information System (INIS)

1988-01-01

The HTR is the only reactor system which can provide process heat in a wide temperature range up to 950 0 C. The HTR module is designed as an unsophisticated, safe and universal heat source with a large field of applications. The following applications have been considered: the steam reforming of natural gas and coal conversion processes for the production of methanol, hydrogen and SNG. They are investigated in many different modifications and nuclear and autothermal processes are compared. Other applications of nuclear process heat in the chemical and petrochemical industry seem to be appropriate and promising, but could not be analysed because of lack of data. The economic results show that for today's coal and gas processing the HTR can only compete against conventional conversion processes for specific premises. Especially, those processses in which valuable fossil fuels such as natural gas are substituted by nuclear process heat promise an economic bebefit. Looking to the market of the year 2030 and the need for process heat in the chemical and steel industries (including the demand for synthesis gas), cement and refinery industries, for the production of aluminium oxide and for tertiary oil recovery, a total theoretical market in the Federal Republic of Germany of up to 60 HTR-2 module plants is estimated

Reactivity control in HTR power plants with respect to passive safety system. Summary

Energy Technology Data Exchange (ETDEWEB)

Barnert, H; Kugeler, K [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Sicherheitsforschung und Reaktortechnik

1996-12-01

The R and D and Demonstration of the High Temperature Reactor (HTR) is described in overview. The HTR-MODULE power plant, as the most advanced concept, is taken for the description of the reactivity control in general. The idea of the ``modularization of the core`` of the HTR has been developed as the answer on the experiences of the core melt accident at Three Miles Island. The HTR module has two shutdown systems: The ``6 rods``-system for hot shutdown at the ``18 small absorber pebbles units`` - system for cold shutdown. With respect to the definition of ``Passive Systems`` of IAEA-TECDOC-626 the total reactivity control system of the HTR-MODULE is a passive system of category D, because it is an emergency reactor shutdown system based on gravity driven rods, and devices, activated by fail-safe trip logic. But reactivity control of the HTR does not only consist of these engineered safety system but does have a self-acting stabilization by the negative temperature coefficient of the reactivity, being rather effective in reactivity control. Examples from computer calculations are presented, and, in addition, experimental results from the ``Stuck Rod Experiment`` at the AVR reactor in Juelich. On the basis of this the proposal is made that ``self-acting stabilization as a quality of the function`` should be discussed as a new category in addition to the active and passive engineered safety systems, structures and components of IAEA-TECDOC-626. The requirements for a future ``catastrophe-free`` nuclear technology are presented. In the appendix the 7th amendment of the atomic energy act of the Federal Republic of Germany, effective 28 July 94, is given. (author).

The present state of the HTR concept based on experience gained from AVR and THTR

International Nuclear Information System (INIS)

Wachholz, W.

1989-01-01

During the past ten years the development of a specific HTR concept has made remarkable progress. This has been mainly characterized by making use of the safety characteristics typical of the High-Temperature Reactor (HTR). In the design, construction and operation of High-Temperature Reactors - especially AVR (15 MWe plant in Juelich, FRG) and THTR (300 MWe plant in Hamm-Uentrop, FRG) - comprehensive experience has been gained in the field of operational availability and safety, accident topology and plant risk of HTRs in recent years. This experience is relevant for the entire HTR line independent of specific projects. (author). 3 refs, 5 figs, 1 tab

Analysis and primary design of the I and C system architecture for HTGR-10 reactor

International Nuclear Information System (INIS)

Yang Zijue; Zhao Guoji

1993-01-01

The consideration of making good use of the-state-of-the-arts technology in designing advanced Instrumentation and Control System architecture is discussed. A fully distributed and fully micro-computerized, local network based Instrumentation and Control System is designed for the HTR-10 reactor. The advantages of the system architecture include high reliability and availability, flexibility, economics, etc. It also fits for other production processes

Studies on the effects of the hypothetic accidents in HTR reactors. (phase 1). HSK 1. Pt. 1

International Nuclear Information System (INIS)

Gabriel, H.W.; Redondo, J.A.

1977-09-01

The report is an attempt to outline the possibilities of a quantitative, i.e. objective safety assessment. The basic problem here are the controversial opinions an the term of 'risk'. As long as there is no technically and legally acceptable compromise between the opinion 'risk equals extent of damage' and the probabilistic concept, systems in development must follow both approaches. Using the HTR-1160 as an example, studies on the determination of the maximum possible extent of damage in nuclear power plants have been carried out with a special view to determining the rate of the course of extreme accident combinations. Knowledge on this point helps to quantify the chances to prevent the accident itself as well as the chances to protect the population. One basic assumption is that there are no active safety measures to ameliorate the course of the accident (hypothetic accident chains). Consequence analysis is based on nothing but analytically and experimentally validable data, i.e. 'natural law data' on the failure of passive reactor components. Present findings show that HTR reactors can be designed in such manner that accidents with vicinity dose development velocities above 100 rem/5 h are practically impossible. The time history of dose development velocities in the vicinity can be superposed by the course of possible administrative measures. Risk values can then be assessed with sufficient accuracy. (orig./HP) [de

Two-branch Gas Experiments for Hot Gas Mixing of HTR-PM

International Nuclear Information System (INIS)

Zhou Yangping; Hao Pengefei; He Heng; Li Fu; Shi Lei

2014-01-01

A model experiment is proposed to investigate the hot gas mixing efficiency of HTR-PM reactor outlet. The test facility is introduced which is set at a scale of 1:2.5 comparing with the design of thermal mixing structure at HTR-PM reactor outlet. The test facility using air as its flow media includes inlet pipe system, electric heaters, main body of test facility, hot gas duct, exhaust pipe system and I&C system. Two-branch gas experiments are conducted on the test facility and the values of thermal-fluid parameters are collected and analyzed which include the temperature, pressure and velocity of the flow as well as the temperature of the tube wall. The analysis result shows the mixing efficiency is higher than the requirement of thermal mixing by steam generator even with conservative assumption which indicates that the design of hog gas mixing structure of HTR-PM fulfills the requirement for thermal mixing at two-branch working conditions. (author)

Fission Product Releases from a Core into a Coolant of a Prismatic 350-MWth HTR

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Min; Jo, C. K. [KAERI, Daejeon (Korea, Republic of)

2016-05-15

A prismatic 350-MW{sub th} high temperature reactor (HTR) is a means to generate electricity and process heat for hydrogen production. The HTR will be operated for an extended fuel burnup of more than 150 GWd/MTU. Korea Atomic Energy Research Institute (KAERI) is performing a point design for the HTR which is a pre-conceptual design for the analysis and assessment of engineering feasibility of the reactor. In a prismatic HTR, metallic and gaseous fission products (FPs) are produced in the fuel, moved through fuel materials, and released into a primary coolant. The FPs released into the coolant are deposited on the various helium-wetted surfaces in the primary circuit, or they are sorbed on particulate matters in the primary coolant. The deposited or sorbed FPs are released into the environment through the leakage or venting of the primary coolant. It is necessary to rigorously estimate such radioactivity releases into the environment for securing the health and safety of the occupational personnel and the public. This study treats the FP releases from a core into a coolant of a prismatic 350-MW{sub th} HTR. These results can be utilized as input data for the estimation of FP migration from a coolant into the environment. The analysis of fission product release within a prismatic 350-MW{sub th} HTR has been done. It was assumed that the HTR was operated at constant temperature and power for 1500 EFPDs. - The final burnup is 152 GWd/tHM at packing fraction of 25 %, and the final fast fluence is about 8 X 10{sup 21} n/cm{sup 2}, E{sub n} > 0.1 MeV. - The temperatures at the compact center and at the center of a kernel located at the compact center are 884 and 893 .deg. C, respectively, when the packing fraction is 25 % and the coolant temperature is 850 .deg. C. - Xenon is the most radioactive fission product in a coolant of a prismatic HTR when there are broken TRISOs and fuel component contaminated with heavy metals. For metallic fission products, the radioactivity

The conceptual flowsheet of effluent treatment during preparing spherical fuel elements of HTR

Energy Technology Data Exchange (ETDEWEB)

Ying, Quan, E-mail: quanying@tsinghua.edu.cn; Xiao-tong, Chen; Bing, Liu; Gen-na, Fu; Yang, Wang; You-lin, Shao; Zhen-ming, Lu; Ya-ping, Tang; Chun-he, Tang

2014-05-01

High temperature gas-cooled reactor (HTR) is one of the advanced nuclear reactors owing to its inherent safety and broad applications. For HTR, one of the key components is the ceramic fuel element. During the preparation of spherical fuel elements, the radioactive effluent treatment is necessary. Referring to the current treatment technologies and methods, the conceptual flowsheet of low-level radioactive effluent treatment during preparing spherical fuel elements was established. According to the above treatment process, the uranium concentration was decreased from 200 mg/l to the level of discharged standard.

New Developments in Actinides Burning with Symbiotic LWR-HTR-GCFR Fuel Cycles

International Nuclear Information System (INIS)

Bomboni, Eleonora

2008-01-01

The long-term radiotoxicity of the final waste is currently the main drawback of nuclear power production. Particularly, isotopes of Neptunium and Plutonium along with some long-lived fission products are dangerous for more than 100000 years. 96% of spent Light Water Reactor (LWR) fuel consists of actinides, hence it is able to produce a lot of energy by fission if recycled. Goals of Generation IV Initiative are reduction of long-term radiotoxicity of waste to be stored in geological repositories, a better exploitation of nuclear fuel resources and proliferation resistance. Actually, all these issues are intrinsically connected with each other. It is quite clear that these goals can be achieved only by combining different concepts of Gen. IV nuclear cores in a 'symbiotic' way. Light-Water Reactor - (Very) High Temperature Reactor ((V)HTR) - Fast Reactor (FR) symbiotic cycles have good capabilities from the viewpoints mentioned above. Particularly, HTR fuelled by Plutonium oxide is able to reach an ultra-high burn-up and to burn Neptunium and Plutonium effectively. In contrast, not negligible amounts of Americium and Curium build up in this core, although the total mass of Heavy Metals (HM) is reduced. Americium and Curium are characterised by an high radiological hazard as well. Nevertheless, at least Plutonium from HTR (rich in non-fissile nuclides) and, if appropriate, Americium can be used as fuel for Fast Reactors. If necessary, dedicated assemblies for Minor Actinides (MA) burning can be inserted in Fast Reactors cores. This presentation focuses on combining HTR and Gas Cooled Fast Reactor (GCFR) concepts, fuelled by spent LWR fuel and depleted uranium if need be, to obtain a net reduction of total mass and radiotoxicity of final waste. The intrinsic proliferation resistance of this cycle is highlighted as well. Additionally, some hints about possible Curium management strategies are supplied. Besides, a preliminary assessment of different chemical forms of

PEMODELAN TERAS UNTUK ANALISIS PERHITUNGAN KONSTANTA MULTIPLIKASI REAKTOR HTR-PROTEUS

Directory of Open Access Journals (Sweden)

Zuhair Zuhair

2015-04-01

Full Text Available PTRKN sebagai salah satu unit kerja di BATAN dengan tugas pokok dan fungsi yang berkaitan erat dengan teknologi reaktor dan keselamatan nuklir, menaruh perhatian khusus pada konsep reaktor pebble bed. Dalam makalah ini pemodelan reaktor pebble bed HTR-PROTEUS dilakukan dengan program transport Monte Carlo MCNP5. Partikel bahan bakar berlapis TRISO dimodelkan secara detail dan eksak dimana distribusi acak partikel ini dalam bola bahan bakar didekati menggunakan array teratur kisi SC dengan fraksi packing 5,76% tanpa zona eksklusif. Model teras pebble bed didekati dengan memanfaatkan kisi teratur dari bola yang disusun sebagai kisi BCC berdasarkan sel berulang yang digenerasi dari sejumlah sel satuan. Hasil perhitungan MCNP5 memperlihatkan kesesuaian yang sangat baik dengan eksperimen, walaupun teras HTR-PROTEUS diprediksi lebih reaktif daripada pengukuran, khususnya di teras 4.2 dan 4.3. Pustaka ENDF/B-VI menunjukkan konsistensi dengan estimasi keff paling akurat dibandingkan pustaka ENDF/B-V, terutama ENDF/B-VI (66c. Deviasi estimasi keff yang dihitung dengan eksperimen dikaitkan sebagai konsekuensi dari komposisi reflektor grafit yang dispesifikasikan. Komparasi yang dibuat memperlihatkan bahwa MCNP5 menghasilkan keff teras HTR-PROTEUS lebih presisi daripada hasil dari MCNP4B dan MCNPBALL. Hasil ini menyimpulkan bahwa, sukses metodologi pemodelan ini menjustifikasi aplikasi MCNP5 untuk analisis reaktor pebble bed lainnya. Kata kunci: pemodelan teras HTR-PROTEUS, konstanta multiplikasi, MCNP5   PTRKN as a working unit in BATAN whose main duties and functions are related to reactor technology and nuclear safety, consern attention to pebble bed reactor concept. In this paper modeling of HTR-PROTEUS pebble bed reactor was done using Monte Carlo transport code MCNP5. The TRISO coated fuel particle is modeled in detailed and exact manner where random distributions of these particles in fuel pebble is approximated by using regular array of SC lattice

Survey of appropriate endothermic processes for association with the HTR

International Nuclear Information System (INIS)

Brown, G.; Harrison, G.E.; Gent, C.W.; Plummer, J.

1975-01-01

Emphasis is placed on association of the HTR system as a heat source with chemical processes requiring temperatures up to 850 to 900 0 C, corresponding to a reactor coolant temperature of 950 0 C, though processes requiring temperatures up to 1100 0 C and above are reviewed. Particular attention is given to processes for the production of hydrogen-containing gases, including coal/lignite gasification which has been the subject of a recent study. Rising fuel prices make the HTR an attractive proposition if design concepts and materials can be developed to match the requirements. Other appropriate endothermic processes considered are oil processing, including tar sands and shales, and also energy production. Since the full temperature range of the reactor system must be utilised mention is made of low grade heat uses. Even very large chemical works have relatively small energy requirement by nuclear heat standards and adoption of the HTR as a heat source is likely only if it is associated with a large chemical/metallurgical complex or with the processing of a natural resource. (author)

Coal conversion and the HTR - basic elements of novel power supply concepts

International Nuclear Information System (INIS)

Buerger, F.H.

1985-01-01

A meeting under this title was held in Dortmund on 16 to 19 September, 1985, jointly by the VGB Technische Vereinigung der Grosskraftwerksbetreiber e.V., Essen, and the Vereinigte Elektrizitaetswerke Westfalen AG (VEW), Dortmund. The meeting was held in two sections: 'Gersteinwerk power plant - the combination unit K and the KUV coal conversion system' and '7th International conference on HTR technology'. Three technologies were discussed that will have a significant role on the future energy market, i.e., the HTR reactor line (first applied in the Hamm-Uentrop THTR reactor), the new generation of coal-fired power plants with combined gas/steam turbines, and the coal gasification technology. All three systems will make more efficient and less-polluting use of domestic coal by using HTR process heat, by converting coal to widen its range of applications, and by providing more efficient combination units for power plants. (orig./UA) [de

Solution of multiple circuits of steam cycle HTR system

International Nuclear Information System (INIS)

Li, Fu; Wang, Dengying; Hao, Chen; Zheng, Yanhua

2014-01-01

In order to analyze the dynamic operation performance and safety characteristics of the steam cycle high temperature gas cooled reactor (HTR) systems, it is necessary to find the solution of the whole HTR systems with all coupled circuits, including the primary circuit, the secondary circuit, and the residual heat removal system (RHRS). Considering that those circuits have their own individual fluidity and characteristics, some existing code packages for independent circuits themselves have been developed, for example THEMRIX and TINTE code for the primary circuit of the pebble bed reactor, BLAST for once through steam generator. To solve the coupled steam cycle HTR systems, a feasible way is to develop coupling method to integrate these independent code packages. This paper presents several coupling methods, e.g. the equivalent component method between the primary circuit and steam generator which reflect the close coupling relationship, the overlapping domain decomposition method between the primary circuit and the passive RHRS which reflects the loose coupling relationship. Through this way, the whole steam cycle HTR system with multiple circuits can be easily and efficiently solved by integration of several existing code packages. Based on this methodology, a code package TINTE–BLAST–RHRS was developed. Using this code package, some operation performance of HTR–PM was analyzed, such as the start-up process of the plant, and the depressurized loss of forced cooling accident when different number of residual heat removal trains is operated

Study on simulation, control and online assistance integrated system of 10 MW high temperature gas-cooled test reactor

International Nuclear Information System (INIS)

Luo, S.; Shi, L.; Zhu, S.

2004-01-01

In order to provide a convenient tool for engineering designed, safety analysis, operator training and control system design of the high temperature gas-cooled test reactor (HTR), an integrated system for simulation, control and online assistance of the HTR-10 has been designed and is still under development by the Institute of Nuclear Energy Technology (INET) of Tsinghua University in China. The whole system is based on a network environment and includes three subsystems: the simulation subsystem (SIMUSUB), the visualized control designed subsystem (VCDSUB) and the online assistance subsystem (OASUB). The SIMUSUB consists of four parts: the simulation calculating server (SCS), the main control client (MCC), the data disposal client (DDC) and the results graphic display client (RGDC), all of which can communicate with each other via network. The SIMUSUB is intended to analyze and calculate the physical processes of the reactor core, the main loop system and the stream generator, etc., as well as to simulate the normal operation and transient accidents, and the result data can be graphically displayed through the RGDC dynamically. The VCDSUB provides a platform for control system modeling where the control flow systems can be automatically generated and graphically simulated. Based on the data from the field bus, the OASUB provides some of the reactor core parameter, which are difficult to measure. This whole system can be used as an educational tool to understand the design and operational characteristics of the HTR-10, and can also provide online supports for operators in the main control room, or as a convenient powerful tool for the control system design. (authors)

LEU-HTR critical experiment program for the PROTEUS facility in Switzerland

International Nuclear Information System (INIS)

Brogli, R.; Bucher, K.H.; Chawla, R.; Foskolos, K.; Luchsinger, H.; Mathews, D.; Sarlos, G.; Seiler, R.

1990-01-01

New critical experiments in the framework of an IAEA Coordinated Research Program on 'Validation of Safety Related Reactor Physics Calculations for Low Enriched HTRs' are planned at the PSI PROTEUS facility. The experiments are designed to supplement the experimental data base and reduce the design and licensing uncertainties for small- and medium-sized helium-cooled reactors using low-enriched uranium (LEU) and graphite high temperature fuel. The main objectives of the new experiments are to provide first-of-a-kind high quality experimental data on: 1) The criticality of simple, easy to interpret, single core region LEU HTR systems for several moderator-to-fuel ratios and several lattice geometries; 2) the changes in reactivity, neutron balance components and control rod effectiveness caused by water ingress into this type of reactor, and 3) the effects of the boron and/or hafnium absorbers that are used to modify the reactivity and the power distributions in typical HTR systems. Work on the design and licensing of the modified PROTEUS critical facility is now in progress with the HTR experiments scheduled to begin early in 1991. Several international partners will be involved in the planning, execution and analysis of these experiments in order to insure that they are relevant and cost effective with respect to the various gas cooled reactor national programs. (author)

LEU-HTR critical experiment program for the PROTEUS facility in Switzerland

Energy Technology Data Exchange (ETDEWEB)

Brogli, R; Bucher, K H; Chawla, R; Foskolos, K; Luchsinger, H; Mathews, D; Sarlos, G; Seiler, R [Paul Scherrer Institute, Laboratory for Reactor Physics and System Technology Wuerenlingen and Villigen, Villigen PSI (Switzerland)

1990-07-01

New critical experiments in the framework of an IAEA Coordinated Research Program on 'Validation of Safety Related Reactor Physics Calculations for Low Enriched HTRs' are planned at the PSI PROTEUS facility. The experiments are designed to supplement the experimental data base and reduce the design and licensing uncertainties for small- and medium-sized helium-cooled reactors using low-enriched uranium (LEU) and graphite high temperature fuel. The main objectives of the new experiments are to provide first-of-a-kind high quality experimental data on: 1) The criticality of simple, easy to interpret, single core region LEU HTR systems for several moderator-to-fuel ratios and several lattice geometries; 2) the changes in reactivity, neutron balance components and control rod effectiveness caused by water ingress into this type of reactor, and 3) the effects of the boron and/or hafnium absorbers that are used to modify the reactivity and the power distributions in typical HTR systems. Work on the design and licensing of the modified PROTEUS critical facility is now in progress with the HTR experiments scheduled to begin early in 1991. Several international partners will be involved in the planning, execution and analysis of these experiments in order to insure that they are relevant and cost effective with respect to the various gas cooled reactor national programs. (author)

Procedures and results of the probabilistic safety study of the HTR-1160 plant

International Nuclear Information System (INIS)

Kroeger, W.; Bongartz, R.

1981-01-01

A research team of the Institute for Nuclear Safety Research of the Juelich Nuclear Research Center (KFA) and staff members of the Gesellschaft fuer Reaktorsicherheit, sponsored by the Federal Ministry of the Interior, carried out a safety and risk analysis of high temperature reactors. The studies, which included the transfer to German conditions and the modification in some points of methodology of the American AIPA Study, were performed on the German concept of an 1160 MWe HTR with block-type fuel elements. They referred to accidents and possible impacts on the environment, residual risks and measures to reduce them. The study covered a total of approx. 15 groups of initiating events, including potential external impacts. The dominating initiating events are transients in a pressurized reactor. Differences relative to the light water reactor concept arise with respect to releases as a result of accidents and, above all, release times; they are due to different physical characteristics. HTR'S are characterized by thermal inertia and resistance to temperatures. If the results of the study are extended to the HTR line with a pebble bed core currently in the planning phase, the power densities alone, which are considerably lower in some designs, are indicative of an even more effective fission product retention than is already found in the HTR-1160 plant analyzed here. (orig.) [de

10 years of current generation in the AVR reactor

International Nuclear Information System (INIS)

Schenk, P.; Nehrling, H.; Daeunert, U.; Schulten, R.

1978-01-01

On 17th December 1967, the experimental nuclear power plant (AVR) in Juelich supplied RWE network with power for the first time. With the start of the power operation of the first German high-temperature reactor (HTR), a milestone was reached in the development of this new and progressive line of construction. On the same day exactly 10 years later, the successful work with the hottest nuclear reactor in the world was reviewed in the presence of 15 associates of the Arbeitsgemeinschaft Versuchsreaktor (AVR) Ltd. and the personnel of the experimental nuclear power plant at a festival event in the main auditorium of the nuclear power plant at Juelich before some 300 guests from central and local government, the board of control, representatives of the population of the Dueren area and the town of Juelich, as well as bodies of the power producing industry. (orig.) [de

Design investigation of the HTR for the opening of very heavy oil deposits

International Nuclear Information System (INIS)

Gao, Z.

1985-02-01

In the north-east of China there are rich deposits of very heavy oil, which are to be found in a depth of 1500-1700 m. For opening an interaction of 370-390 0 Celsius steam is necessary. The HTR is well suited to produce the steam. A nuclear heat source of 1000 MWsub(th) makes possible the production of 1.5 million tons oil per year. This is a 30-40 per cent higher production of oil compared to the oil-fired steam production. Two concepts of smaller pebble bed reactors are suited as heat sources: the HTR-MEDUL-334 with a thermal power of the 334 MW and fuelled in the multiple run-through scheme and the HTR-OTTO-200 with 200 MW and once-through fuelling. Three or five reactors can be combined in the modular way to provide the power of 1000 MW. For both reactors the design, the neutron-physical and thermohydraulic behaviour are followed in the computer simulation. A central zone of the pebble bed reactor is fuelled with elements of strongly reduced fissile content. Due to the reduced power density the maximum fuel temperature appearing in extreme accidents is limited and accordingly the release of the fission products is avoided. (orig.) [de

Comparative study of random and uniform models for the distribution of TRISO particles in HTR-10 fuel elements

International Nuclear Information System (INIS)

Rosales, J.; Perez, J.; Garcia, C.; Munnoz, A.; Lira, C. A. B. O.

2015-01-01

TRISO particles are the specific features of HTR-10 and generally HTGR reactors. Their heterogeneity and random arrangement in graphite matrix of these reactors create a significant modeling challenge. In the simulation of spherical fuel elements using MCNPX are usually created repetitive structures using uniform distribution models. The use of these repetitive structures introduces two major approaches: the non-randomness of the TRISO particles inside the pebbles and the intersection of the pebble surface with the TRISO particles. These approaches could affect significantly the multiplicative properties of the core. In order to study the influence of these approaches in the multiplicative properties was estimated the K inf value in one pebble with white boundary conditions using 4 different configurations regarding the distribution of the TRISO particles inside the pebble: uniform hexagonal model, cubic uniform model, cubic uniform without the effect of cutting and a random distribution model. It was studied the impact these models on core scale solving the problem B1, from the Benchmark Problems presented in a Coordinated Research Program of the IAEA. (Author)

Study on the shuffling scheme in HTR-10 MW test module

International Nuclear Information System (INIS)

Jing Xingqing; Zhang Xu; Luo Jingyu

1993-01-01

The shuffling ways, once through then out and multiple through then out, in HTR-10 MW Test Module are studied. Multiple through then out is better than once through with regard to rational use of the fuel and flattening the power. The behaviour of equilibrium core and loss of coolant accident is analyzed. The results indicate that characteristic features of the multiple through then out could be better to satisfy the demands of safety criterions

HTR-E project. High-temperature components and systems

International Nuclear Information System (INIS)

Breuil, E.; Exner, R.

2002-01-01

The HTR-E European project (four years project) is proposed for the 5th Framework Programme and concerns the technical developments needed for the innovative components of a modern HTR with a direct cycle. These components have been selected with reference to the present projects (GT-MHR, PBMR): (1) the helium turbine, the recuperator heat exchanger, the electro-magnetic bearings and the helium rotating seal; (2) the tribology. Sliding innovative components in helium environment are particularly concerned. (3) the helium purification system. Recommendations on impurities contents have to be provided in accordance with the materials proposed for the innovative components. The main outcomes expected from the HTR-E project are the design recommendations and identification of further R and D needs for these components. This will be based: (1) on experience feedback from European past helium test loops and reactors; (2) on design studies, thermal-hydraulic and structural analyses; (3) and on experimental tests

Study of the Effect of Burnable Poison Particles Applying in a Pebble Bed HTR

International Nuclear Information System (INIS)

Wei Chunlin; Zhao Jing; Zhang Jian; Xia Bing

2014-01-01

In pebble bed high temperature gas cooled reactors (HTR), spherical fuel elements pass through the core several times to balance the burnup process in the fuel region, resulting in an acceptable shape and peak factor of power density in the simulation analysis. In contrast, when fuel elements pass through the core only once, the peak of power density occurs at the top of the core and its value is too high to be safe. These indicators/parameters can be improved by incorporating burnable poison in the fuel elements under certain conditions. In the current study, burnable poison particles (BPPs) in fuel elements are evaluated. In spite of the strong absorption capability of "1"0B, BPPs can decrease the depletion speed and increase the duration of "1"0B because of the self-shielding effect, resulting in improved shape and peak factor of power distribution. Several BPPs with different radius are discussed in power distribution, following the calculation for a full-scale reactor core with modified VSOP code. According the result, applying BPPs on fuel pebbles is an effective means to improve the distribution of the power density under one-through fuel load in HTR. (author)

Preliminary design study of pebble bed reactor HTR-PM base using once-through-then-out fuel recirculation

International Nuclear Information System (INIS)

Topan Setiadipura; Jupiter S Pane; Zuhair

2016-01-01

Pebble Bed Reactor (PBR) is one of the advanced reactor type implementing strong passive safety feature. In this type of design has the potential to do a cogeneration useful for the treatment of various minerals in various islands in Indonesia. The operation of the PBR can be simplified by implementing once-through-then-out (OTTO) fuel recirculation scheme in which pebble fuel only pass the core once time. The purpose of this research is to understand quantitative influence of the changing of fuel element recirculation on the PBR core performance and to find preliminary optimization design of PBR type reactor with OTTO recirculation scheme. PEBBED software was used to find PBR equilibrium core. The calculation result gives quantitative data on the impact of implementing a different fuel recirculation, especially using OTTO scheme. Furthermore, an early optimized PBR design based on HTR-PM using OTTO scheme was obtained where the power must be downgraded into 115 MWt in order to preserve the safety feature. The simplicity of the reactor operation and the reduction of reactor component with OTTO scheme still make this early optimized design an interesting alternative design, despite its power reduction from the reference design. (author)

Relationship between the Toyo Tanso Group and HTR-PM

International Nuclear Information System (INIS)

Zhan Guobin; Konishi, Takashi

2014-01-01

IG-110 that is Isotropic graphite for nuclear applications, is the only product that is used for two types of High Temperature Gas-cooled Reactors, prismatic type HTTR and pebble-bed type HTR-10, that are currently in operation in the world. IG-110 is highly evaluated in the global market for its track record and physical stability. The Toyo Tanso Group won the contract to build graphite core internals for HTR-PM that is a world’s first modular pebble-bed high temperature gas-cooled demonstration reactor. A decision was made to manufacture IG-110 graphite materials at Toyo Tanso Japan called TTJ and to process products and undertake temporary assembly at Shanghai Toyo Tanso called STT. Manufacture of graphite materials for which TTJ is responsible has been completed. As the next step, processing of products is scheduled to commence at STT from this autumn. Our graphite materials were required to be 2,000 mm or more in maximum length. The number of graphite blocks required exceeded 3,500. Although the graphite structure requirements including configuration were highly challenging, we were able to meet all the requirements with our engineering capabilities, i.e. decades of track record in manufacture and stability in characteristics. STT that will start the machining process this autumn is equipped with state-of-the-art processing machines and three-dimensional measuring machines. Notably, STT has high levels of engineering capabilities to process and inspect tens of thousands of internal components for reactors in accordance with drawings and to temporarily assemble these components. (author)

Modular high-temperature reactor launched (and wallchart)

International Nuclear Information System (INIS)

Steinwarz, W.

1987-01-01

In view of the need for a technically unsophisticated, safe and economic reactor system, the KWU group has integrated the experience gained from German light-water reactor engineering and from successful operation of the German AVR experimental high-temperature reactor into the development of the High-Temperature Reactor (HTR)-module. The main components are illustrated and explained and technical data for the HTR-module is given. Safety is also considered. This includes graphs of core heat-up temperature for pebble-bed HTR and a graph of the temperature load of the fuel elements. The operation, control and applications are considered. The latter includes use in combined heat and power generation and community heating. Feasibility studies have shown that the HTR-module is cheaper, comparatively, than coal-fired power stations. (U.K.)

Prospective studies of HTR fuel cycles involving plutonium

International Nuclear Information System (INIS)

Bonin, B.; Greneche, D.; Carre, F.; Damian, F.; Doriath, J.Y.

2002-01-01

High Temperature Gas Cooled reactors (HTRs) are able to accommodate a wide variety of mixtures of fissile and fertile materials without any significant modification of the core design. This flexibility is due to an uncoupling between the parameters of cooling geometry, and the parameters which characterize neutronic optimisation (moderation ratio or heavy nuclide concentration and distribution). Among other advantageous features, an HTR core has a better neutron economy than a LWR because there is much less parasitic capture in the moderator (capture cross section of graphite is 100 times less than the one of water) and in internal structures. Moreover, thanks to the high resistance of the coated particles, HTR fuels are able to reach very high burn-ups, far beyond the possibilities offered by other fuels (except the special case of molten salt reactors). These features make HTRs especially interesting for closing the nuclear fuel cycle and stabilizing the plutonium inventory. A large number of fuel cycle studies are already available today, on 3 main categories of fuel cycles involving HTRs : i) High enriched uranium cycle, based on thorium utilization as a fertile material and HEU as a fissile material; ii) Low enriched uranium cycle, where only LEU is used (from 5% to 12%); iii) Plutonium cycle based on the utilization of plutonium only as a fissile material, with (or without) fertile materials. Plutonium consumption at high burnups in HTRs has already been tested with encouraging results under the DRAGON project and at Peach Bottom. To maximize plutonium consumption, recent core studies have also been performed on plutonium HTR cores, with special emphasis on weapon-grade plutonium consumption. In the following, we complete the picture by a core study for a HTR burning reactor-grade plutonium. Limits in burnup due to core neutronics are investigated for this type of fuel. With these limits in mind, we study in some detail the Pu cycle in the special case of a

Standard and chances of the HTR in the Federal Republic of Germany

International Nuclear Information System (INIS)

Simon, M.; Harder, H.

1980-01-01

If one believes the verbal support of the politicians on the High-Temperature Reactor this reactor type seems to have a good future. The facts show that inspite of the well known properties of the HTR and the engagement of the industry and potential operators, progress is hardly made. Soon it could be too late for this reactor line. (orig.) [de

Would HTR be suitable for application in the Netherlands?

International Nuclear Information System (INIS)

Heek, A.I. van.

1994-08-01

The modular HTR may be a reactor type, which would have sufficient societal support to be constructed in the Netherlands. The economic approach would be fundamentally different from that applied in present nuclear technology. In a national research program this is being investigated. (orig.)

Preparation of spherical fuel elements for HTR-PM in INET

International Nuclear Information System (INIS)

Xiangwen, Zhou; Zhenming, Lu; Jie, Zhang; Bing, Liu; Yanwen, Zou; Chunhe, Tang; Yaping, Tang

2013-01-01

Highlights: • Modifications and optimizations in the manufacture of spherical fuel elements (SFE) for HTR-PM are presented. • A newly developed overcoater exhibits good stability and high efficiency in the preparation of overcoated particles. • The optimized carbonization process reduces the process time from 70 h in the period of HTR-10 to 20 h. • Properties of the prepared SFE and matrix graphite balls meet the design specifications for HTR-PM. • In particular the mean free uranium fraction of 5 consecutive batches is only 8.7 × 10 −6 . -- Abstract: The spherical fuel elements were successfully manufactured in the period of HTR-10. In order to satisfy the mass production of fuel elements for HTR-PM, several measures have been taken in modifying and optimizing the manufacture process of fuel elements. The newly developed overcoater system and its corresponding parameters exhibited good stability and high efficiency in the preparation of overcoated particles. The optimized carbonization process could reduce the carbonization time from more than 70 h to 20 h and improve the manufacturing efficiency. Properties of the manufactured spherical fuel elements and matrix graphite balls met the design specifications for HTR-PM. The mean free uranium fraction of 5 consecutive batches was 8.7 × 10 −6 . The optimized fuel elements manufacturing process could meet the requirements of design specifications of spherical fuel elements for HTR-PM

Accident situations tests HTR fuel with the device Kufa

International Nuclear Information System (INIS)

Kellerbauer, A. I.; Freis, D.

2010-01-01

The ceramic and ceramic-like coating materials in modern high-temperature reactor fuel are designed to ensure mechanical stability and retention of fission products under normal and transient conditions, regardless of the radiation damage sustained in-pile. In hypothetical depressurization and loss-of-forced-circulation (D LOFC) accidents, fuel elements of modular high-temperate reactors are exposed to temperatures several hundred degrees higher than during normal operation, causing increased thermo-mechanical stress on the coating layers. At the Institute for Transuranium Elements of the European Commission, a vigorous experimental program is being pursued with the aim of characterizing the performance of irradiated HTR fuel under such accident conditions. A cold finger device (Kufa), operational in ITUs hot cells since 2006, has been used to perform heating experiments on eight irradiated HTR fuel pebbles from the AVR experimental reactor and from dedicated irradiation campaigns at the High-Flux Reactor in Petten, the Netherlands. Gaseous fission products are collected in a cryogenic charcoal trap, while volatiles,are plated out on a water-cooled condensate plate. A quantitative measurement of the release is obtained by gamma spectroscopy. We highlight experimental results from the Kufa testing as well as the on-going development of new experimental facilities. (Author) 9 refs.

Benchmark Analysis Of The High Temperature Gas Cooled Reactors Using Monte Carlo Technique

International Nuclear Information System (INIS)

Nguyen Kien Cuong; Huda, M.Q.

2008-01-01

Information about several past and present experimental and prototypical facilities based on High Temperature Gas-Cooled Reactor (HTGR) concepts have been examined to assess the potential of these facilities for use in this benchmarking effort. Both reactors and critical facilities applicable to pebble-bed type cores have been considered. Two facilities - HTR-PROTEUS of Switzerland and HTR-10 of China and one conceptual design from Germany - HTR-PAP20 - appear to have the greatest potential for use in benchmarking the codes. This study presents the benchmark analysis of these reactors technologies by using MCNP4C2 and MVP/GMVP Codes to support the evaluation and future development of HTGRs. The ultimate objective of this work is to identify and develop new capabilities needed to support Generation IV initiative. (author)

HTR's role in process heat applications

International Nuclear Information System (INIS)

Kuhr, Reiner

2008-01-01

Advanced high-temperature nuclear reactors create a number of new opportunities for nuclear process heat applications. These opportunities are based on the high-temperature heat available, smaller reactor sizes, and enhanced safety features that allow siting close to process plants. Major sources of value include the displacement of premium fuels and the elimination of CO 2 emissions from combustion of conventional fuels and their use to produce hydrogen. High value applications include steam production and cogeneration, steam methane reforming, and water splitting. Market entry by advanced high-temperature reactor technology is challenged by the evolution of nuclear licensing requirements in countries targeted for early applications, by the development of a customer base not familiar with nuclear technology and related issues, by convergence of oil industry and nuclear industry risk management, by development of public and government policy support, by resolution of nuclear waste and proliferation concerns, and by the development of new business entities and business models to support commercialization. New HTR designs may see a larger opportunity in process heat niche applications than in power given competition from larger advanced light water reactors. Technology development is required in many areas to enable these new applications, including the commercialization of new heat exchangers capable of operating at high temperatures and pressures, convective process reactors and suitable catalysts, water splitting system and component designs, and other process-side requirements. Key forces that will shape these markets include future fuel availability and pricing, implementation and monetization of CO 2 emission limits, and the formation of international energy and environmental policy that will support initiatives to provide the nuclear licensing frameworks and risk distribution needed to support private investment. This paper was developed based on a plenary

Process heat applications of HTR-PM600 in Chinese petrochemical industry: Preliminary study of adaptability and economy

International Nuclear Information System (INIS)

Fang, Chao; Min, Qi; Yang, Yanran; Sun, Yuliang

2017-01-01

Highlights: •High Temperature Gas Cooled Reactor (HTGR) could work as heat source for petrochemical industry. •The joint of a 600 MW modular HTGR (HTR-PM600) and petrochemical industry is achievable. •The mature technology of turbine in thermal power station could be readily adopted. •The economy of this scheme is also acceptable. -- Abstract: High Temperature Gas Cooled Reactor (HTGR) could work as heat source for petrochemical industry. In this article, the preliminary feasibility of a 600 MW modular HTGR (HTR-PM600) working as heat source for a typical hypothetical Chinese petrochemical factory is discussed and it is found that the joint of HTR-PM600 and petrochemical industry is achievable. In detail, the heat and water balance analysis of the petrochemical factory is given. Furthermore, the direct cost of heat supplied by HTR-PM600 is calculated and corresponding economy is estimated. The results show that though there are several challenges, the application of process heat of HTGR to petrochemical industry is practical in sense of both technology and economy.

Studies on high temperature research reactor in China

Energy Technology Data Exchange (ETDEWEB)

Xu Yuanhui; Zuo Kanfen [Institute of Nuclear Energy Technology, Tsinghua Univ., Beijing (China)

1999-08-01

China recognises the advantages of Modular HTGRs and has chosen Modular HTGRs as one of advanced reactors to be developed for the further intensive utilisation of nuclear power in the next century. In energy supply systems of the next century, HTGR is supposed to serve: 1. as supplement to water-cooled reactors for electricity generation and 2. as environmentally friendly heat source providing process heat at different temperatures for various applications like heavy oil recovery, coal gasification and liquefaction, etc.. The 10 MW High Temperature Gas-cooled Reactor (HTR-10) is a major project in the energy sector of the Chinese National High Technology Programme as the first step of development of Modular HTGRs in China. Its main objectives are: 1. to acquire know-how in the design, construction and operation of HTGRs, 2. to establish an irradiation and experimental facility, 3. to demonstrate the inherent safety features of Modular HTGR, 4. to test electricity and heat co-generation and closed cycle gas turbine technology and 5. to do research and development work on the nuclear process heat application. Now the HTR-10 is being constructed at the site of Institute of Nuclear Energy Technology (INET). The HTR-10 project is to be carried out in two phases. In the first phase, the reactor with an coolant outlet temperature of 700degC will be coupled with a steam generator providing steam for a steam turbine cycle which works on an electricity and heat co-generation basis. In the second phase, the reactor coolant outlet temperature is planned to be raised to 900degC. As gas turbine cycle and a steam reformer will be coupled to the reactor in addition to the steam turbine cycle. (author)

Studies on high temperature research reactor in China

International Nuclear Information System (INIS)

Xu Yuanhui; Zuo Kanfen

1999-01-01

China recognises the advantages of Modular HTGRs and has chosen Modular HTGRs as one of advanced reactors to be developed for the further intensive utilisation of nuclear power in the next century. In energy supply systems of the next century, HTGR is supposed to serve: 1. as supplement to water-cooled reactors for electricity generation and 2. as environmentally friendly heat source providing process heat at different temperatures for various applications like heavy oil recovery, coal gasification and liquefaction, etc.. The 10 MW High Temperature Gas-cooled Reactor (HTR-10) is a major project in the energy sector of the Chinese National High Technology Programme as the first step of development of Modular HTGRs in China. Its main objectives are: 1. to acquire know-how in the design, construction and operation of HTGRs, 2. to establish an irradiation and experimental facility, 3. to demonstrate the inherent safety features of Modular HTGR, 4. to test electricity and heat co-generation and closed cycle gas turbine technology and 5. to do research and development work on the nuclear process heat application. Now the HTR-10 is being constructed at the site of Institute of Nuclear Energy Technology (INET). The HTR-10 project is to be carried out in two phases. In the first phase, the reactor with an coolant outlet temperature of 700degC will be coupled with a steam generator providing steam for a steam turbine cycle which works on an electricity and heat co-generation basis. In the second phase, the reactor coolant outlet temperature is planned to be raised to 900degC. As gas turbine cycle and a steam reformer will be coupled to the reactor in addition to the steam turbine cycle. (author)

Perspectives for the french R and D program for high and very high temperature reactors - HTR2008-58172

International Nuclear Information System (INIS)

Yvon, P.; Hittner, D.; Delbecq, J. M.

2008-01-01

A R and D programme has been launched addressing the needs of the development of an indirect cycle flexible modular HTR operating at 850 deg. C for electricity generation and/or heat production for industrial processes. In the frame of this program, several significant technical challenges required to demonstrate the viability and performance of the system have been successfully addressed. Design and safety analysis needed the development of computational tools, therefore reactor physics, and thermo-fluid dynamics codes have been developed and are now in the process of being validated in the frame of international code-to-code and code to experiment benchmarks. Most importantly, the performance of the HTR/VHTR fuel identified as TRISO-coated particle must prove to be excellent in operating as well as accidental conditions. A manufacturing and quality control process has been developed and now fuel qualification based on irradiation and heating safety tests is being prepared on the basis of irradiation programs in France and in the frame of the GENERATION IV International Forum (GIF) as well as the development of fuel behaviour models including performance data, failure particle prediction and long-term integrity of the coating. Material and component technologies have been investigated in normal and accident conditions for V/HTR objectives. Significant progress has been made for vessel structures and reactor core structural elements. Major challenges still lie ahead for plate type compact intermediate heat exchangers, especially at temperatures above 850 deg. C, but an alternative solution with helical tubes is also being developed. In order to demonstrate that materials have adequate performance over long service life under impure helium environment and constraints, the research programme focuses on microstructural and mechanical property data, long-term irradiation behaviour, corrosion, modelling and codification of design rules as well as qualification of

First Results for Fluid Dynamics, Neutronics and Fission Product Behaviour in HTR applying the HTR Code Package (HCP) Prototype

International Nuclear Information System (INIS)

Allelein, H.-J.; Kasselmann, S.; Xhonneux, A.; Lambertz, D.

2014-01-01

To simulate the different aspects of High Temperature Reactor (HTR) cores, a variety of specialized computer codes have been developed at Forschungszentrum Jülich (IEK-6) and Aachen University (LRST) in the last decades. In order to preserve knowledge, to overcome present limitations and to make these codes applicable to modern computer clusters, these individual programs are being integrated into a consistent code package. The so-called HTR code package (HCP) couples the related and recently applied physics models in a highly integrated manner and therefore allows to simulate phenomena with higher precision in space and time while at the same time applying state-of-the-art programming techniques and standards. This paper provides an overview of the status of the HCP and reports about first benchmark results for an HCP prototype which couples the fluid dynamics and time dependent neutronics code MGT-3D, the burn up code TNT and the fission product release code STACY. Due to the coupling of MGT-3D and TNT, a first step towards a new reactor operation and accident simulation code was made, where nuclide concentrations calculated by TNT are fed back into a new spectrum code of the HCP. Selected operation scenarios of the HTR-Module 200 concept plant and the HTTR were chosen to be simulated with the HCP prototype. The fission product release during normal operation conditions will be calculated with STACY based on a core status derived from SERPENT and MGT–3D. Comparisons will be shown against data generated by the legacy codes VSOP99/11, NAKURE and FRESCO-II. (author)

First results for fluid dynamics, neutronics and fission product behavior in HTR applying the HTR code package (HCP) prototype

Energy Technology Data Exchange (ETDEWEB)

Allelein, H.-J., E-mail: h.j.allelein@fz-juelich.de [Forschungszentrum Jülich, 52425 Jülich (Germany); Institute for Reactor Safety and Reactor Technology, RWTH Aachen University, 52064 Aachen (Germany); Kasselmann, S.; Xhonneux, A.; Tantillo, F.; Trabadela, A.; Lambertz, D. [Forschungszentrum Jülich, 52425 Jülich (Germany)

2016-09-15

To simulate the different aspects of High Temperature Reactor (HTR) cores, a variety of specialized computer codes have been developed at Forschungszentrum Jülich (IEK-6) and Aachen University (LRST) in the last decades. In order to preserve knowledge, to overcome present limitations and to make these codes applicable to modern computer clusters, these individual programs are being integrated into a consistent code package. The so-called HTR code package (HCP) couples the related and recently applied physics models in a highly integrated manner and therefore allows to simulate phenomena with higher precision in space and time while at the same time applying state-of-the-art programming techniques and standards. This paper provides an overview of the status of the HCP and reports about first benchmark results for an HCP prototype which couples the fluid dynamics and time dependent neutronics code MGT-3D, the burn up code TNT and the fission product release code STACY. Due to the coupling of MGT-3D and TNT, a first step towards a new reactor operation and accident simulation code was made, where nuclide concentrations calculated by TNT lead to new cross sections, which are fed back into MGT-3D. Selected operation scenarios of the HTR-Module 200 concept plant and the HTTR were chosen to be simulated with the HCP prototype. The fission product release during normal operation conditions will be calculated with STACY based on a core status derived from SERPENT and MGT-3D. Comparisons will be shown against data generated by SERPENT and the legacy codes VSOP99/11, NAKURE and FRESCO-II.

Materials for high temperature reactor vessels

International Nuclear Information System (INIS)

Buenaventura Pouyfaucon, A.

2004-01-01

Within the 5th Euraton Framework Programme, a big effort is being made to promote and consolidate the development of the High Temperature Reactor (HTR). Empresarios Agrupados is participating in this project and among others, also forms part of the HTR-M project Materials for HTRs. This paper summarises the work carried out by Empresarios Agrupados regarding the material selection of the HTR Reactor Pressure Vessel (RPV). The possible candidate materials and the most promising ones are discussed. Design aspects such as the RPV sensitive zones and material damage mechanisms are considered. Finally, the applicability of the existing design Codes and Standards for the design of the HTR RPV is also discussed. (Author)

Study on the Break Accidents of the HTR-PM Primary Loop

International Nuclear Information System (INIS)

Lang Minggang; Sun Ximing; Zheng Yanhua

2014-01-01

In thermal hydraulics design and safety analysis of the HTR-PM, the THERMIX code was used to study the behavior of the helium in the primary system. Once the helium leaks from the primary loop through a break or a relief valve, it is hard to simulate the states of the leakage room with THERMIX. In this paper, the latest version of RELAP5/MOD4, was used to simulate the behavior of the helium released to the containment rooms. A RELAP5/MOD4 model of the HTR-PM, including the core, the primary system, the secondary loop and the containment, were developed and evaluated in this paper. Based on the model, this paper studied the accidents consequences of a large break in the pressure relief room and a small break in the instrument room of the HTR-PM reactor building. The simulating results illustrate that the temperature in the pressure relief room was no more than 200℃ after a un-isolating large break, and the temperature in the instrument room is less than 130 ℃ after a small un-isolating break. The analysis shows that the scram function and the ability to monitor the reactor temperature and pressure after accidents would not be affected by the break. (author)

Design of reactor internals in larger high-temperature reactors with spherical fuel elements

International Nuclear Information System (INIS)

Elter, C.

1981-01-01

In his paper, the author analyzes and summarizes the present state of the art with emphasis on the prototype reactor THTR 300 MWe, because in addition to spherical fuel elements, this type includes other features of future HTR design such as the same flow direction of cooland gas through the core. The paper on hand also elaborates design guidelines for reactor internals applicable with large HTR's of up to 1200 MWe. Proved designs will be altered so as to meet the special requirements of larger cores with spherical elements to be reloaded according to the OTTO principle. This paper is furthermore designed as a starting point for selective and swift development of reactor internals for large HTR's to be refuelled according to the OTTO principle. (orig./GL) [de

Analysis of stress in reactor core vessel under effect of pressure lose shock wave

International Nuclear Information System (INIS)

Li Yong; Liu Baoting

2001-01-01

High Temperature gas cooled Reactor (HTR-10) is a modular High Temperature gas cooled Reactor of the new generation. In order to analyze the safety characteristics of its core vessel in case of large rupture accident, the transient performance of its core vessel under the effect of pressure lose shock wave is studied, and the transient pressure difference between the two sides of the core vessel and the transient stresses in the core vessel is presented in this paper, these results can be used in the safety analysis and safety design of the core vessel of HTR-10. (author)

Progress and problems in modelling HTR core dynamics

International Nuclear Information System (INIS)

Scherer, W.; Gerwin, H.

1991-01-01

In recent years greater effort has been made to establish theoretical models for HTR core dynamics. At KFA Juelich the TINTE (TIme dependent Neutronics and TEmperatures) code system has been developed, which is able to model the primary circuit of an HTR plant using modern numerical techniques and taking into account the mutual interference of the relevant physical variables. The HTR core is treated in 2-D R-Z geometry for both nucleonics and thermo-fluid-dynamics. 2-energy-group diffusion theory is used in the nuclear part including 6 groups of delayed neutron precursors and 14 groups of decay heat producers. Local and non-local heat sources are incorporated, thus simulating gamma ray transport. The thermo-fluid-dynamics module accounts for heterogeneity effects due to the pebble bed structure. Pipes and other components of the primary loop are modelled in 1-D geometry. Forced convection may be treated as well as natural convection in case of blower breakdown accidents. Validation of TINTE has started using the results of a comprehensive experimental program that has been performed at the Arbeitsgemeinschaft Versuchsreaktor GmbH (AVR) high temperature pebble bed reactor at Juelich. In the frame of this program power transients were initiated by varying the helium blower rotational speed or by moving the control rods. In most cases a good accordance between experiment and calculation was found. Problems in modelling the special AVR reactor geometry in two dimensions are described and suggestions for overcoming the uncertainties of experimentally determined control rod reactivities are given. The influence of different polynomial expansions of xenon cross sections to long term transients is discussed together with effects of burnup during that time. Up to now the TINTE code has proven its general applicability to operational core transients of HTR. The effects of water ingress on reactivity, fuel element corrosion and cooling gas properties are now being

Operational requirements of spherical HTR fuel elements and their performance

International Nuclear Information System (INIS)

Roellig, K.; Theymann, W.

1985-01-01

The German development of spherical fuel elements with coated fuel particles led to a product design which fulfils the operational requirements for all HTR applications with mean gas exit temperatures from 700 deg C (electricity and steam generation) up to 950 deg C (supply of nuclear process heat). In spite of this relatively wide span for a parameter with strong impact on fuel element behaviour, almost identical fuel specifications can be used for the different reactor purposes. For pebble bed reactors with relatively low gas exit temperatures of 700 deg C, the ample design margins of the fuel elements offer the possibility to enlarge the scope of their in-service duties and, simultaneously, to improve fuel cycle economics. This is demonstrated for the HTR-500, an electricity and steam generating 500 MWel eq plant presently proposed as follow-up project to the THTR-300. Due to the low operating temperatures of the HTR-500 core, the fuel can be concentrated in about 70% of the pebbles of the core thus saving fuel cycle costs. Under all design accident conditions fuel temperatures are maintained below 1250 deg C. This allows a significant reduction in the engineered activity barriers outside the primary circuit, in particular for the loss of coolant accident. Furthermore, access to major primary circuit components and the reuse of the fuel elements after any design accident are possible. (author)

Plant Operation Station for HTR-PM Low Power and Shutdown operation Probabilistic safety analysis

International Nuclear Information System (INIS)

Liu Tao; Tong Jiejuan

2014-01-01

Full range Probabilistic safety analysis (PSA) is one of key conditions for nuclear power plant (NPP) licensing according to the requirement of nuclear safety regulatory authority. High Temperature Gas Cooled Reactor Pebble-bed Module (HTR-PM) has developed construction design and prepared for the charging license application. So after the normal power operation PSA submitted for review, the Low power and Shutdown operation Probabilistic safety analysis (LSPSA) also begin. The results of LSPSA will together with prior normal power PSA results to demonstrate the safety level of HTR-PM NPP Plant Operation Station (POS) is one of important terms in LSPSA. The definition of POS lays the foundation for LSPSA modeling. POS provides initial and boundary conditions for the following event tree and fault tree model development. The aim of this paper is to describe the state-of-the-art of POS definition for HTR-PM LSPSA. As for the first attempt to the high temperature gas cooled reactor module plant, the methodology and procedure of POS definition refers to the LWR LSPSA guidance, and adds to plant initial status analysis due to the HTR-PM characteristics. A specific set of POS grouping vectors is investigate and suggested for HTR-PM NPP, which reflects the characteristics of plant modularization and on-line refueling. As a result, seven POSs are given according to the grouping vectors at the end of the paper. They will be used to the LSPSA modelling and adjusted if necessary. The papers ’work may provide reference to the analogous NPP LSPSA. (author)

Physics of high-temperature reactors

International Nuclear Information System (INIS)

Massimo, L.

1976-01-01

The subject is covered in chapters entitled: general description of the HTR core; general considerations about reactor physics; neutron cross-sections; basic aspects of transport and diffusion theory; methods for the solution of the diffusion equation; slowing-down and thermalization in graphite; resonance absorption; spectrum calculations and cross-section averaging; burn-up; core design; fuel management and cost calculations; temperature coefficient; core dynamics and accident analysis; reactor control; peculiarities of HTR physics; analysis of calculational accuracy; sequence of reactor design calculations. (U.K.)

Market prospects of modular HTR in EEC countries

International Nuclear Information System (INIS)

Albisu, F.; Garribba, S.F.; Lefevre, J.C.; Leuchs, D.; Vivante, C.

1991-01-01

The energy outlook for the early 21st century is very uncertain. Low-cost oil and natural gas reserves will become seriously depleted and nonfossil energy resources may be urgently required because of environmental reasons. In this framework, small- and medium-size nuclear reactors (SMSNRs), particularly the Modular High-Temperature Reactor (HTR) would allow extension of uses of nuclear energy while being adopted to produce power and/or steam or heat, where heat can be at low or high temperature. For policy making and planning purposes it is meaningful to appraise the market potential of Modular HTR during the next 20 or 30 years. The paper presents the outcomes of country studies on the subject conducted for a sample of EC Member nations, including France, Federal Republic of Germany, Italy, and Spain. Among the goals of the studies are the definition of market segments, and identification of the principal obstacles which will affect future adoption of SMSNRs. Opportunities offered by the different contexts and energy end-uses seem promising. Numerous difficulties and constraints emerge, however, some of which might be eased by actions that national governments or more often the European Community may wish to take. (author)

Graphite Oxidation Simulation in HTR Accident Conditions

Energy Technology Data Exchange (ETDEWEB)

El-Genk, Mohamed

2012-10-19

Massive air and water ingress, following a pipe break or leak in steam-generator tubes, is a design-basis accident for high-temperature reactors (HTRs). Analysis of these accidents in both prismatic and pebble bed HTRs requires state-of-the-art capability for predictions of: 1) oxidation kinetics, 2) air helium gas mixture stratification and diffusion into the core following the depressurization, 3) transport of multi-species gas mixture, and 4) graphite corrosion. This project will develop a multi-dimensional, comprehensive oxidation kinetics model of graphite in HTRs, with diverse capabilities for handling different flow regimes. The chemical kinetics/multi-species transport model for graphite burning and oxidation will account for temperature-related changes in the properties of graphite, oxidants (O2, H2O, CO), reaction products (CO, CO2, H2, CH4) and other gases in the mixture (He and N2). The model will treat the oxidation and corrosion of graphite in geometries representative of HTR core component at temperatures of 900°C or higher. The developed chemical reaction kinetics model will be user-friendly for coupling to full core analysis codes such as MELCOR and RELAP, as well as computational fluid dynamics (CFD) codes such as CD-adapco. The research team will solve governing equations for the multi-dimensional flow and the chemical reactions and kinetics using Simulink, an extension of the MATLAB solver, and will validate and benchmark the model's predictions using reported experimental data. Researchers will develop an interface to couple the validated model to a commercially available CFD fluid flow and thermal-hydraulic model of the reactor , and will perform a simulation of a pipe break in a prismatic core HTR, with the potential for future application to a pebble-bed type HTR.

Nuclear power reactors

International Nuclear Information System (INIS)

1982-11-01

After an introduction and general explanation of nuclear power the following reactor types are described: magnox thermal reactor; advanced gas-cooled reactor (AGR); pressurised water reactor (PWR); fast reactors (sodium cooled); boiling water reactor (BWR); CANDU thermal reactor; steam generating heavy water reactor (SGHWR); high temperature reactor (HTR); Leningrad (RMBK) type water-cooled graphite moderated reactor. (U.K.)

Concept of safety related I and C and power supply systems in the passive safety concept of the HTR-module

International Nuclear Information System (INIS)

Juengst, U.

1990-01-01

The main motivation for the passive safety concepts is to gain a better quality of safety or at least to achieve higher public acceptance for nuclear power plants. This strategy has been introduced into the European Fast Reactor (EER), a common project of France, UK and Germany is applied stringently to the German high-temperature gas-cooled reactor ''HTR - Module''. The following fields are briefly described in the paper: Safety design features of the HTR - Module, overview of I and C concept, reactor protection system, emergency control room, power supply concept, system arrangement and protection against external hazards, accidents sequence of station black-out. (author). 3 figs

High Temperature reactors status 1977

International Nuclear Information System (INIS)

Ekholm, R.; Bosaeus, J.; Carleson, G.; Gelin, R.; Jirlow, K.; Linder, S.; Menon, S.; Runfors, U.; Vieider, G.

1978-03-01

The objective of this report is to summarize the current state-of-the-art of HTR technology as part of follow-up studies of the development of advanced fission reactor systems. These studies have been performed at AB Atomenergi since fiscal year 1975/76 and are financed by governmental funds for energy R and D. In this report emphasis is given to the following main aspects of the HTR development: - a survey of the major HTR - R and D programmes; - the description of HTR technology including remaining development problems and uncertainties; - the analysis of the safety and environmental characteristics of the HTR systems; - the analysis of the incentives for the introduction of various HTR types. The report contains also information kindly provided directly by experts from several organisations developing the HTR-systems

Research on application of burnable poison in pebble bed HTR

International Nuclear Information System (INIS)

Wei Chunlin; Zhang Jian; Shan Wenzhi; Jing Xingqing

2013-01-01

Burnable poison in fuel ball was used in pebble bed high-temperature gas-cooled reactor (HTR) to optimize the shape and the peak factor of power distribution in certain conditions. Two options are available and evaluated, that is the homogeneous burnable poison in graphite matrix and burnable poison particles (BPPs) in fuel balls. Due to the absorption cross section of "1"0B, the depletion speed for homogeneous burnable poison is very fast, and difficult to control, on the other side, the depletion speed of BPPs can be optimized respecting to its size, and better shape and peak value of power distribution can be achieved. (authors)

Evaluation of proposed German safety criteria for high-temperature gas-cooled reactors

International Nuclear Information System (INIS)

Barsell, A.W.

1980-05-01

This work reviews proposed safety criteria prepared by the German Bundesministerium des Innern (BMI) for future licensing of gas-cooled high-temperature reactor (HTR) concepts in the Federal Republic of Germany. Comparison is made with US General Design Criteria (GDCs) in 10CFR50 Appendix A and with German light water reactor (LWR) criteria. Implications for the HTR design relative to the US design and safety approach are indicated. Both inherent characteristics and design features of the steam cycle, gas turbine, and process heat concepts are taken into account as well as generic design options such as a pebble bed or prismatic core

Details of modelling HTR core physics: the use of pseudo nuclide traces

International Nuclear Information System (INIS)

Kuijper, J.C.; Oppe, J.; Haas, J.B.M. de; Da Cruz, D.F.

2003-01-01

At present most combined neutronic and thermal hydraulic analyses of reactors, and the HTR is no exception, are being performed by codes employing few-group (typically 2-group) neutronics on the basis of parametrized few-group macroscopic (and microscopic) cross sections for homogenized areas, depending on quantities like irradiation (fuel only), 135 Xe concentration, temperature, etc. The irradiation parameter (time-integrated power per unit initial heavy metal mass) is sufficient for keeping track of the evolution of areas containing fuel. However, the use of the same parameter in areas without fuel, e.g. containing burnable poison, requires some special provisions. This can be met by the introduction of pseudo nuclides, with very specific cross sections and reaction chains, in the procedure to generate the parametrized few-group cross sections. It is shown that the time-evolution of a non-fuelled burnable poison area, as calculated by the 2-group (HTR) reactor code PANTHERMIX employing pseudo nuclides, compares well to the time-evolution obtained from an explicit burnup calculation by the WIMS8A/SNAP code. Examples are also shown using the pseudo nuclide method to keep track of the fast fluence (time-integrated flux above 0.1 MeV) in a continuous reload pebble-bed HTR reactor calculation by PANTHERMIX. Although the present implementation of the pseudo nuclide method exhibits some peculiarities connected to the specific codes in use (WIMS8A and PANTHERMIX) it is considered to be sufficiently general to be applicable in other code suites, requiring only limited modifications. (authors)

Details of modelling HTR core physics: the use of pseudo nuclide traces

Energy Technology Data Exchange (ETDEWEB)

Kuijper, J.C.; Oppe, J.; Haas, J.B.M. de; Da Cruz, D.F. [Nuclear Research and consultancy Group (NRG), Petten (Netherlands)

2003-07-01

At present most combined neutronic and thermal hydraulic analyses of reactors, and the HTR is no exception, are being performed by codes employing few-group (typically 2-group) neutronics on the basis of parametrized few-group macroscopic (and microscopic) cross sections for homogenized areas, depending on quantities like irradiation (fuel only), {sup 135}Xe concentration, temperature, etc. The irradiation parameter (time-integrated power per unit initial heavy metal mass) is sufficient for keeping track of the evolution of areas containing fuel. However, the use of the same parameter in areas without fuel, e.g. containing burnable poison, requires some special provisions. This can be met by the introduction of pseudo nuclides, with very specific cross sections and reaction chains, in the procedure to generate the parametrized few-group cross sections. It is shown that the time-evolution of a non-fuelled burnable poison area, as calculated by the 2-group (HTR) reactor code PANTHERMIX employing pseudo nuclides, compares well to the time-evolution obtained from an explicit burnup calculation by the WIMS8A/SNAP code. Examples are also shown using the pseudo nuclide method to keep track of the fast fluence (time-integrated flux above 0.1 MeV) in a continuous reload pebble-bed HTR reactor calculation by PANTHERMIX. Although the present implementation of the pseudo nuclide method exhibits some peculiarities connected to the specific codes in use (WIMS8A and PANTHERMIX) it is considered to be sufficiently general to be applicable in other code suites, requiring only limited modifications. (authors)

10 years of current generation in the AVR reactor. The high-temperature pebble-bed reactor - a hot tip for our future

Energy Technology Data Exchange (ETDEWEB)

Schenk, P [Arbeitsgemeinschaft Versuchs-Reaktor G.m.b.H., Juelich (Germany, F.R.); A G, Stadtwerke Duesseldorf [Germany, F.R.; Vereinigung Deutscher Elektrizitaetswerke e.V. (VDEW), Frankfurt am Main (Germany, F.R.)); Nehrling, H [Ministerium fuer Wirtschaft, Mittelstand und Verkehr des Landes Nordrhein-Westfalen, Duesseldorf (Germany, F.R.); Daeunert, U [Bundesministerium fuer Forschung und Technologie, Bonn-Bad Godesberg (Germany, F.R.); Schulten, R [Kernforschungsanlage Juelich G.m.b.H. (Germany, F.R.). Inst. fuer Reaktorentwicklung; Mattick, W [Brown, Boveri und Cie A.G., Mannheim (Germany, F.R.)

1978-02-01

On 17th December 1967, the experimental nuclear power plant (AVR) in Juelich supplied RWE network with power for the first time. With the start of the power operation of the first German high-temperature reactor (HTR), a milestone was reached in the development of this new and progressive line of construction. On the same day exactly 10 years later, the successful work with the hottest nuclear reactor in the world was reviewed in the presence of 15 associates of the Arbeitsgemeinschaft Versuchsreaktor (AVR) Ltd. and the personnel of the experimental nuclear power plant at a festival event in the main auditorium of the nuclear power plant at Juelich before some 300 guests from central and local government, the board of control, representatives of the population of the Dueren area and the town of Juelich, as well as bodies of the power producing industry.

Decommissioning of the Dragon High Temperature Reactor (HTR) Located at the Former United Kingdom Atomic Energy Authority (UKAEA) Research Site at Winfrith - 13180

Energy Technology Data Exchange (ETDEWEB)

Smith, Anthony A. [Research Sites Restoration Ltd, Winfrith, Dorset (United Kingdom)

2013-07-01

The Dragon Reactor was constructed at the United Kingdom Atomic Energy Research Establishment at Winfrith in Dorset through the late 1950's and into the early 1960's. It was a High Temperature Gas Cooled Reactor (HTR) with helium gas coolant and graphite moderation. It operated as a fuel testing and demonstration reactor at up to 20 MW (Thermal) from 1964 until 1975, when international funding for this project was terminated. The fuel was removed from the core in 1976 and the reactor was put into Safestore. To meet the UK's Nuclear Decommissioning Authority (NDA) objective to 'drive hazard reduction' [1] it is necessary to decommission and remediate all the Research Sites Restoration Ltd (RSRL) facilities. This includes the Dragon Reactor where the activated core, pressure vessel and control rods and the contaminated primary circuit (including a {sup 90}Sr source) still remain. It is essential to remove these hazards at the appropriate time and return the area occupied by the reactor to a safe condition. (author)

Analysis of hypothetical incidents in nuclear power plants with PWR and HTR

International Nuclear Information System (INIS)

Geiser, H.

1977-01-01

Several accident analyses are reviewed with a view to fission product release, and the findings are transferred to German reactor plants with LWR and HTR and compared. First of all, hypothetical accidents are compared for both of these lines; after this, the history of accidents is briefly described, and the fission product release during these accidents is investigated. For both reactor lines, there is a different but sufficiently high potential for safety improvements. (orig.) [de

Pilot study of dynamic Bayesian networks approach for fault diagnostics and accident progression prediction in HTR-PM

Energy Technology Data Exchange (ETDEWEB)

Zhao, Yunfei; Tong, Jiejuan; Zhang, Liguo, E-mail: lgzhang@tsinghua.edu.cn; Zhang, Qin

2015-09-15

Highlights: • Dynamic Bayesian network is used to diagnose and predict accident progress in HTR-PM. • Dynamic Bayesian network model of HTR-PM is built based on detailed system analysis. • LOCA Simulations validate the above model even if part monitors are lost or false. - Abstract: The first high-temperature-reactor pebble-bed demonstration module (HTR-PM) is under construction currently in China. At the same time, development of a system that is used to support nuclear emergency response is in progress. The supporting system is expected to complete two tasks. The first one is diagnostics of the fault in the reactor based on abnormal sensor measurements obtained. The second one is prognostic of the accident progression based on sensor measurements obtained and operator actions. Both tasks will provide valuable guidance for emergency staff to take appropriate protective actions. Traditional method for the two tasks relies heavily on expert judgment, and has been proven to be inappropriate in some cases, such as Three Mile Island accident. To better perform the two tasks, dynamic Bayesian networks (DBN) is introduced in this paper and a pilot study based on the approach is carried out. DBN is advantageous in representing complex dynamic systems and taking full consideration of evidences obtained to perform diagnostics and prognostics. Pearl's loopy belief propagation (LBP) algorithm is recommended for diagnostics and prognostics in DBN. The DBN model of HTR-PM is created based on detailed system analysis and accident progression analysis. A small break loss of coolant accident (SBLOCA) is selected to illustrate the application of the DBN model of HTR-PM in fault diagnostics (FD) and accident progression prognostics (APP). Several advantages of DBN approach compared with other techniques are discussed. The pilot study lays the foundation for developing the nuclear emergency response supporting system (NERSS) for HTR-PM.

Irradiation behaviour of advanced fuel elements for the helium-cooled high temperature reactor (HTR)

International Nuclear Information System (INIS)

Nickel, H.

1990-05-01

The design of modern HTRs is based on high quality fuel. A research and development programme has demonstrated the satisfactory performance in fuel manufacturing, irradiation testing and accident condition testing of irradiated fuel elements. This report describes the fuel particles with their low-enriched UO 2 kernels and TRISO coating, i.e. a sequence of pyrocarbon, silicon carbide, and pyrocarbon coating layers, as well as the spherical fuel element. Testing was performed in a generic programme satisfying the requirements of both the HTR-MODUL and the HTR 500. With a coating failure fraction less than 2x10 -5 at the 95% confidence level, the results of the irradiation experiments surpassed the design targets. Maximum accident temperatures in small, modular HTRs remain below 1600deg C, even in the case of unrestricted core heatup after depressurization. Here, it was demonstrated that modern TRISO fuels retain all safety-relevant fission products and that the fuel does not suffer irreversible changes. Isothermal heating tests have been extended to 1800deg C to show performance margins. Ramp tests to 2500deg C demonstrate the limits of present fuel materials. A long-term programm is planned to improve the statistical significance of presently available results and to narrow remaining uncertainty limits. (orig.) [de

The HTR, applications, economics and environmental aspects

International Nuclear Information System (INIS)

Barnert, H.; Schad, M.; Candeli, H.

1990-01-01

The High Temperature Reactor (HTR), as the only nuclear system producing high temperature heat up to 1000 deg. C, offers a wide variety of applications. Besides electricity production, via steam turbines and in future via gas turbines, there is: District heat with high efficiency, long distance energy for urban energy supply, high pressure injection steam production for enhanced oil recovery, medium range temperature heat direct application in chemical and related industry and last not least, high temperature application for the refinement of fossil energy carriers. Recent results of studies and programmes will be presented: Near term applications are identified, e.g. refineries and alumina industry with smaller HTR units. Another large market is the production of hydrogen, methanol and ammonia on the basis of natural gas, the relevant technology has been developed up to the pilot scale. The refinement of fossil energy carriers, in particular of coal, is subject of the R+D programme in the cooperation between German industrial companies and the Nuclear Research Center. The results are very promising and will be explained in detail. This programme will be continued. Objectives are: improvement of the technology and of the economics as well as environmental aspects, e.g. the reduction of emissions of carbon-dioxid. The topics of the programme deal with the different apparatus, e.g. steam methane reformer, steam coal gasifier, intermediate heat exchanger and last not least, the process heat HTR. (author)

Safety study for HTR conceptual designs under German siting conditions. Phase I B, specialized volume I

International Nuclear Information System (INIS)

1982-08-01

The basic methodology for determining sequences of events and their frequencies (events and fault trees) does not differ significantly from that of other risk studies. This applies analogously to the treatment of statistical data uncertainties and the description of results in the form of expected value with uncertainty factor. System unavailabilities are determined by means of failure rates, most of which originate from the German Risk Study, and consecutive test intervals. Unlike in other risk studies, common mode failures of components of the same kind are being considered by a mostly 10% fraction of the overall failure of the multi-train system (β-factor). A multitude of planned or unplanned operator actions are identified in the study. They are assessed using models from AIPA and according to WASH-1400. HTR-specific aspects allow mitigating operator actions in the range of days, which are approximately covered by subjective estimates, and extensive reversibility of human errors. British experience with gas-cooled reactors proved to be useful for HTR-specific components. Rates of 0.2 to 1 for small leaks and 1.5 x 10 -3 per reactor-year for larger leaks (tube ruptures) are derived on the basis of 2000 steam generator operating years. Failures of the main blowers (0.1 per blower-year) are covered by other transient events. The behaviour of structural components is of great significance for the progression of core heatup accidents. The liner of the reactor pressure vessel and the concrete located behind will fail over a large area due to decreasing strength at temperatures above 800 0 C. A rupture of closure plugs may be virtually precluded. This also applies to a failure of the reactor containment at internal design pressure. The ultimate strength will only be reached at pressures of more than 14 bar. (orig.) [de

The properties of spherical fuel elements and its behavior in the modular HTR

International Nuclear Information System (INIS)

Lohnert, G.H.; Ragoss, H.

1985-01-01

The reference fuel element for all future HTR applications in the Federal Republic of Germany as developed by NUKEM/HOBEG in the framework of the 'High temperature Fuel-Cycle Project' had to be scrutinised for its compatibility with all the other design principles of the modular HTR, or possibly for restrictions forced upon reactor layout. This reference fuel element can be characterized by the following features: moulded spherical fuel element of 60 mm in diameter with fuel free shell of 5 mm thickness, based on carbon matrix; low enriched uranium (U/Pu fuel cycle); UO 2 fuel kernels; TRISO coating (pyrocarbon and additional SiC layers)

Actinide production in different HTR-fuel cycle concepts

International Nuclear Information System (INIS)

Filges, D.; Hecker, R.; Mirza, N.; Rueckert, M.

1978-01-01

At the 'Institut fuer Reaktorentwicklung der Kernforschungsanlage Juelich' the production of α-activities in the following HTR-OTTO cycle concepts were studied: 1. standard HTR cycle (U-Th); 2. low enriched HTR cycle (U-Pu); 3. near breeder HTR cycle (U-Th); 4. combined system (conventional and near breeder HTR). The production of α-activity in HTR Uranium-Thorium fuel cycles has been investigated and compared with the standard LWR cycles. The production of α-activity in HTR Uranium-Thorium fuel cycles has been investigated and compared with the standard LWR cycles. The calculations were performed by the short depletion code KASCO and the well-known ORIGEN program

Core dynamics of HTR under ATWS and accident conditions

International Nuclear Information System (INIS)

Nabbi, R.

1988-05-01

The systematic classification of the ATWS has been undertaken by analogy to the considerations made for LWR. The initiating events of ATWS and protection actions of safety systems resulting from monitoring of the system variables have been described. The main emphasis of this work is the analysis of the core dynamic consequences of scram failure during the anticipated transients. The investigation has shown that because of the temperature feedback mechanisms a temperature rise during the ATWS results in a self-shutdown of the reactor. Further inherent safety features of the HTR - conditioned by the high heat capacity of the core and by the compressibility of the coolant - do effectively counteract an undesirable increase of temperature and pressure in the primary circuit. In case of the long-term failure of the forced cooling and following core heatup, neutron physical phenomena appear which determine the reactivity behaviour of the HTR. They are, for instance, the decay of Xenon 135, release of the fission products and subsiding of the top reflector. The results of the computer simulations show that a recriticality has to be excluded during the first 2 days if the reactor is shutdown by the reflector rods at the beginning of the accident. (orig./HP) [de

Design criteria for high-temperature-affected, metallic and ceramic components, and for the prestressed concrete reactor pressure vessel of future HTR systems. Final report. Vol. 1-4

International Nuclear Information System (INIS)

1988-08-01

This work in five separate volumes reports on the elaboration of basic data for the formulation of design criteria for HTR components and is arranged into the four following subject areas : (1) safety-specific limiting conditions; (2) metallic components; (3) prestressed concrete reactor pressure vessels; (4) graphitic reactor internals. Under item 2, the mechanical and physical characteristics of the materials X20CrMoV 12 1, X10NiCrAlTi 32 20, and NiCr23Co12Mo are examined up to temperatures of 950deg C. Stress-strain rate laws are elaborated for description of the inelastic deformation behavior. The representation of the subject area reactor pressure vessels deals with four main topics: Prestressed concrete support structure, liner, vessel closures, thermal protection system. Quality-assurance classes are defined under item 4 for graphitic components and load levels for load categories. The material evaluation is discussed in detail (e.g. manufacturing monitoring from the raw material to the graphitization and manufacturing testing up to the acceptance test). In addition, the corrosion behavior and irradiation behavior of graphite is examined and rules for computation of stresses in irradiated and unirradiated graphitic components are elaborated. (MM) [de

Deep Burn: Development of Transuranic Fuel for High-Temperature Helium-Cooled Reactors- Monthly Highlights September 2010

International Nuclear Information System (INIS)

Snead, Lance Lewis; Besmann, Theodore M.; Collins, Emory D.; Bell, Gary L.

2010-01-01

The DB Program monthly highlights report for August 2010, ORNL/TM-2010/184, was distributed to program participants by email on September 17. This report discusses: (1) Core and Fuel Analysis - (a) Core Design Optimization in the HTR (high temperature helium-cooled reactor) Prismatic Design (Logos), (b) Core Design Optimization in the HTR Pebble Bed Design (INL), (c) Microfuel analysis for the DB HTR (INL, GA, Logos); (2) Spent Fuel Management - (a) TRISO (tri-structural isotropic) repository behavior (UNLV), (b) Repository performance of TRISO fuel (UCB); (3) Fuel Cycle Integration of the HTR (high temperature helium-cooled reactor) - Synergy with other reactor fuel cycles (GA, Logos); (4) TRU (transuranic elements) HTR Fuel Qualification - (a) Thermochemical Modeling, (b) Actinide and Fission Product Transport, (c) Radiation Damage and Properties; (5) HTR Spent Fuel Recycle - (a) TRU Kernel Development (ORNL), (b) Coating Development (ORNL), (c) Characterization Development and Support, (d) ZrC Properties and Handbook; and (6) HTR Fuel Recycle - (a) Graphite Recycle (ORNL), (b) Aqueous Reprocessing, (c) Pyrochemical Reprocessing METROX (metal recovery from oxide fuel) Process Development (ANL).

Market prospects of modular HTR in EEC countries

International Nuclear Information System (INIS)

Albisu, F.; Garribba, S.F.; Lefevre, J.C.; Leuchs, D.; Vivante, C.

1992-01-01

The energy outlook for the early 21st century is very uncertain. Low-cost oil and natural gas reserves will become seriously depleted and non-fossil energy resources may be urgently required because of environmental reasons. In this framework, the European Economic Community should be able to rely upon nuclear energy as an economic, safe and readily deployable resource for its future. Small and medium-size nuclear reactors (SMSNRs), particularly modular high-temperature reactor (HTR) would allow extension of uses of nuclear energy while being adopted to produce power and/or steam or heat, where heat can be at low or high temperature. For policy making and planning purposes it appears meaningful to appraise the market potential of modular HTR during the next twenty or thirty years. Thus the paper presents the outcomes of country studies on the subject conducted for a sample of Member nations to the European Economic Community including France, Federal Republic of Germany, Italy and Spain. Amongst the goals of the studies are definition of market segments, identification of the principal obstacles which would affect future adoption of SMSNRs. Opportunities offered by the different contexts and energy end-uses seem promising. Numerous difficulties and constraints emerge however, some of which might be eased by actions that national governments or more often the European Economic Community, may wish to take. (orig.)

Gas-cooled reactor programs. High-temperature gas-cooled reactor technology development program. Annual progress report, December 31, 1983

International Nuclear Information System (INIS)

Kasten, P.R.; Rittenhouse, P.L.; Bartine, D.E.; Sanders, J.P.

1984-06-01

ORNL continues to make significant contributions to the national program. In the HTR fuels area, we are providing detailed statistical information on the fission product retention performance of irradiated fuel. Our studies are also providing basic data on the mechanical, physical, and chemical behavior of HTR materials, including metals, ceramics, graphite, and concrete. The ORNL has an important role in the development of improved HTR graphites and in the specification of criteria that need to be met by commercial products. We are also developing improved reactor physics design methods. Our work in component development and testing centers in the Component Flow Test Loop (CFTL), which is being used to evaluate the performance of the HTR core support structure. Other work includes experimental evaluation of the shielding effectiveness of the lower portions of an HTR core. This evaluation is being performed at the ORNL Tower Shielding Facility. Researchers at ORNL are developing welding techniques for attaching steam generator tubing to the tubesheets and are testing ceramic pads on which the core posts rest. They are also performing extensive testing of aggregate materials obtained from potential HTR site areas for possible use in prestressed concrete reactor vessels. During the past year we continued to serve as a peer reviewer of small modular reactor designs being developed by GA and GE with balance-of-plant layouts being developed by Bechtel Group, Inc. We have also evaluated the national need for developing HTRs with emphasis on the longer term applications of the HTRs to fossil conversion processes

Gas-cooled reactor programs. High-temperature gas-cooled reactor technology development program. Annual progress report, December 31, 1983

Energy Technology Data Exchange (ETDEWEB)

Kasten, P.R.; Rittenhouse, P.L.; Bartine, D.E.; Sanders, J.P.

1984-06-01

ORNL continues to make significant contributions to the national program. In the HTR fuels area, we are providing detailed statistical information on the fission product retention performance of irradiated fuel. Our studies are also providing basic data on the mechanical, physical, and chemical behavior of HTR materials, including metals, ceramics, graphite, and concrete. The ORNL has an important role in the development of improved HTR graphites and in the specification of criteria that need to be met by commercial products. We are also developing improved reactor physics design methods. Our work in component development and testing centers in the Component Flow Test Loop (CFTL), which is being used to evaluate the performance of the HTR core support structure. Other work includes experimental evaluation of the shielding effectiveness of the lower portions of an HTR core. This evaluation is being performed at the ORNL Tower Shielding Facility. Researchers at ORNL are developing welding techniques for attaching steam generator tubing to the tubesheets and are testing ceramic pads on which the core posts rest. They are also performing extensive testing of aggregate materials obtained from potential HTR site areas for possible use in prestressed concrete reactor vessels. During the past year we continued to serve as a peer reviewer of small modular reactor designs being developed by GA and GE with balance-of-plant layouts being developed by Bechtel Group, Inc. We have also evaluated the national need for developing HTRs with emphasis on the longer term applications of the HTRs to fossil conversion processes.

Proceedings of the workshop on structural design criteria for HTR

International Nuclear Information System (INIS)

Breitbach, G.; Schubert, F.; Nickel, H.

1989-04-01

The papers demonstrate the status of high temperature reactor technology with regard to its realization in the nuclear power industry of various countries (FRG, USA, Japan) as well as to the development of safety rules in Germany. The design criteria for HTR could be presented. The criteria already determine definitely and almost completely the relevant requirements of the component rules. The informations include the technical boundary conditions with regard to safety, the metallic high temperature components, a particular section dealing with the reactor pressure vessel, especially with the prestressed concrete vessel, and the structural graphite components. (DG)

Possible future roles for the high temperature gas-cooled reactor (HTR) in the community

International Nuclear Information System (INIS)

1978-11-01

Possible roles for HTR in different European nuclear energy strategies are examined from the standpoint of long-term uranium and capital conservation. Two different growth scenarios for European Community electrical energy demand have been assumed (fig. 1). Both curves have been developed from existing short-term forecasts and commitments already made by member states. The lower curve represents a realistic minimum development of per capita energy demand from 3.3 toe/y in 1975 to a ceiling of 6.1 toe/year in 2035 that still lies 30% below current U.S. consumption. Electricity is assumed to increase its share of the total energy market from 28% (1976) to 35%. The higher growth curve represents an increase in overall energy consumption to a level corresponding to 8 toe per capita per year, while the electricity share increase to 67% of the overall demand. It is appreciated that such an increase in the electricity share of the overall demand is unrealistic; its consideration in the present study must therefore be regarded as tending to explore an extreme case of electricity demand growth. A long-term view is taken to show how far future developments are affected by decisions taken in the medium-term. Saturation is assumed in order to force complete development of steady state conditions, in which the relationship between different reactors can be readily discerned and capital needs compared. At saturation uranium price and availability become unimportant in systems containing thermal and breeder reactors in symbiosis

Research on Fault Diagnosis of HTR-PM Based on Multilevel Flow Model

International Nuclear Information System (INIS)

Zhang Yong; Zhou Yangping

2014-01-01

In this paper, we focus on the application of Multilevel Flow Model (MFM) in the automatic real-time fault diagnosis of High Temperature Gas-cooled Reactor Pebble-bed Module (HTR-PM) accidents. In the MFM, the plant process is described abstractly in function level by mass, energy and information flows, which reveal the interaction between different components and capacitate the causal reasoning between functions according to the flow properties. Thus, in the abnormal status, a goal-function-component oriented fault diagnosis can be performed with the model at a very quick speed and abnormal alarms can be also precisely explained by the reasoning relationship of the model. By using MFM, a fault diagnosis model of HTR-PM plant is built, and the detailed process of fault diagnosis is also shown by the flowcharts. Due to lack of simulation data about HTR-PM, experiments are not conducted to evaluate the fault diagnosis performance, but analysis of algorithm feasibility and complexity shows that the diagnosis system will have a good ability to detect and diagnosis accidents timely. (author)

New approaches in the USA for high-temperature gas-cooled reactors. Gas-Cooled Reactor Programs

International Nuclear Information System (INIS)

Kasten, P.R.; Neylan, A.J.; Penfield, S.R. Jr.

1985-08-01

Several concepts are being evaluated in the US HTR Program to explore designs which might improve the commercial viability of nuclear power. The general approach is to reduce the reactor power and increase the ability to use inherent features for removing heat following extreme accidents. The unit size and design of these concepts are constrained so that extreme accidents do not result in significant release of radioactivity from the reactor plant. Through the greater reliance on inherent safety features in small HTRs, it should be possible to minimize the amount of nuclear grade components required in the balance-of-plant, which could lead to an economic system. Four HTR concepts are presently being evaluated within the US Program, and these concepts are briefly summarized. A modular HTR using a steel pressure vessel, which is very similar to one of the four HTR concepts being evaluated within the US National program, is presented as an example of a specific concept to illustrate the features and performance of HTRs having a high degree of inherent safety

High-temperature reactor developments in the Netherlands

International Nuclear Information System (INIS)

Schram, R.P.C.; Cordfunke, E.H.P.; Heek, A.I. van

1996-01-01

The high-temperature reactor development in the Netherlands is embedded in the WHITE reactor program, in which several Dutch research institutes and engineering companies participate. The activities within the WHITE program are focused on the development of a small scale HTR for combined heat and power generation. In 1995, design choices for a pebble bed reactor were made at ECN. The first concept HTR will have a closed cycle helium turbine and a power level of 40 MWth. It is intended to make the market introduction of a commercially competitive HTR feasible. As a part of the HTR program at ECN, chemical aspects of HTR fuel and coated particles are studied. Experimental work on the oxidation resistance of coating materials and fission product attack on coating materials as well as thermochemical calculations of the fuel particles are done at ECN. The concept-HTR of ECN is fuelled with UO 2 , but the use of thorium is considered. The composition of the fuel determines the oxygen potential, which plays a key role in chemical safety of the fuel. Thermochemical calculations of the chemical form of cesium inside the HTR fuel particles were performed for a wide oxygen potential range. The chemical form of cesium determines the cesium pressure inside the fuel particle, which in turn determines the release behavior of Cs from defective particles. At normal operating temperatures and low oxygen potentials, the chemical form of cesium is C 60 Cs. It is known that cesium carbon compounds decompose above 650degC in vacuum. The stability of these compounds in the fuel particles at high temperatures(1000-1600degC) is questioned. Decomposition of these compounds may result in high cesium pressures even at normal operating conditions. Experimental work on the thermodynamic properties of cesium compounds at high temperatures is currently performed. (J.P.N.)

The effects of applying silicon carbide coating on core reactivity of pebble-bed HTR in water ingress accident

Energy Technology Data Exchange (ETDEWEB)

Zuhair, S.; Setiadipura, Topan [National Nuclear Energy Agency of Indonesia, Serpong Tagerang Selatan (Indonesia). Center for Nuclear Reactor Technology and Safety; Su' ud, Zaki [Bandung Institute of Technology (Indonesia). Dept. of Physics

2017-03-15

Graphite is used as the moderator, fuel barrier material, and core structure in High Temperature Reactors (HTRs). However, despite its good thermal and mechanical properties below the radiation and high temperatures, it cannot avoid corrosion as a consequence of an accident of water/air ingress. Degradation of graphite as a main HTR material and the formation of dangerous CO gas is a serious problem in HTR safety. One of the several steps that can be adopted to avoid or prevent the corrosion of graphite by the water/air ingress is the application of a thin layer of silicon carbide (SiC) on the surface of the fuel element. This study investigates the effect of applying SiC coating on the fuel surfaces of pebble-bed HTR in water ingress accident from the reactivity points of view. A series of reactivity calculations were done with the Monte Carlo transport code MCNPX and continuous energy nuclear data library ENDF/B-VII at temperature of 1200 K. Three options of UO{sub 2}, PuO{sub 2}, and ThO{sub 2}/UO{sub 2} fuel kernel were considered to obtain the inter comparison of the core reactivity of pebble-bed HTR in conditions of water/air ingress accident. The calculation results indicated that the UO{sub 2}-fueled pebble-bed HTR reactivity was slightly reduced and relatively more decreased when the thickness of the SiC coating increased. The reactivity characteristic of ThO{sub 2}/UO{sub 2}-fueled pebble-bed HTR showed a similar trend to that of UO{sub 2}, but did not show reactivity peak caused by water ingress. In contrast with UO{sub 2}- and ThO{sub 2}-fueled pebble-bed HTR, although the reactivity of PuO{sub 2}-fueled pebble-bed HTR was the lowest, its characteristics showed a very high reactivity peak (0.33 Δk/k) and this introduction of positive reactivity is difficult to control. SiC coating on the surface of the plutonium fuel pebble has no significant impact. From the comparison between reactivity characteristics of uranium, thorium and plutonium cores with 0.10

The high-temperature reactor's attractiveness lies in passive safety

International Nuclear Information System (INIS)

Anon.

1987-01-01

In the recent years the use of nuclear energy has turned from a technical and scientific issue to a political one. The high-temperature reactor (HTR) however, has always been advertised as particularly safe. The present situation and future developments of HTR-technology were the two issues that VDI-News brought up on the 27th October on an HTR-conference in an interview with the 'spiritual father' of the HTR, Prof. Dr. Rudolf Schulten of the Juelich Nuclear Research Centre. (orig.) [de

Advancements in reactor physics modelling methodology of Monte Carlo Burnup Code MCB dedicated to higher simulation fidelity of HTR cores

International Nuclear Information System (INIS)

Cetnar, Jerzy

2014-01-01

The recent development of MCB - Monte Carlo Continuous Energy Burn-up code is directed towards advanced description of modern reactors, including double heterogeneity structures that exist in HTR-s. In this, we exploit the advantages of MCB methodology in integrated approach, where physics, neutronics, burnup, reprocessing, non-stationary process modeling (control rod operation) and refined spatial modeling are carried in a single flow. This approach allows for implementations of advanced statistical options like analysis of error propagation, perturbation in time domain, sensitivity and source convergence analyses. It includes statistical analysis of burnup process, emitted particle collection, thermal-hydraulic coupling, automatic power profile calculations, advanced procedures of burnup step normalization and enhanced post processing capabilities. (author)

Development of computational methods for the safety assessment of gas-cooled high-temperature and supercritical light-water reactors. Final report; Rechenmethoden zur Bewertung der Sicherheit von gasgekuehlten Hochtemperaturreaktoren und superkritischen Leichtwasserreaktoren. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Buchholz, S.; Cron, D. von der; Hristov, H.; Lerchl, G.; Papukchiev, A.; Seubert, A.; Sureda, A.; Weis, J.; Weyermann, F.

2012-12-15

This report documents developments and results in the frame of the project RS1191 ''Development of computational methods for the safety assessment of gas-cooled high temperature and supercritical light-water reactors''. The report is structured according to the five work packages: 1. Reactor physics modeling of gas-cooled high temperature reactors; 2. Coupling of reactor physics and 3-D thermal hydraulics for the core barrel; 3. Extension of ATHLET models for application to supercritical reactors (HPLWR); 4. Further development of ATHLET for application to HTR; 5. Further development and validation of ANSYS CFX for application to alternative reactor concepts. Chapter 4 describes the extensions made in TORT-TD related to the simulation of pebble-bed HTR, e.g. spectral zone buckling, Iodine-Xenon dynamics, nuclear decay heat calculation and extension of the cross section interpolation algorithms to higher dimensions. For fast running scoping calculations, a time-dependent 3-D diffusion solver has been implemented in TORT-TD. For the PBMR-268 and PBMR-400 as well as for the HTR-10 reactor, appropriate TORT-TD models have been developed. Few-group nuclear cross sections have been generated using the spectral codes MICROX- 2 and DRAGON4. For verification and validation of nuclear cross sections and deterministic reactor models, MCNP models of reactor core and control rod of the HTR-10 have been developed. Comparisons with experimental data have been performed for the HTR-10 first criticality and control rod worth. The development of the coupled 3-D neutron kinetics and thermal hydraulics code system TORT-TD/ATTICA3D is documented in chapter 5. Similar to the couplings with ATHLET and COBRA-TF, the ''internal'' coupling approach has been implemented. Regarding the review of experiments and benchmarks relevant to HTR for validation of the coupled code system, the PBMR-400 benchmarks and the HTR-10 test reactor have been selected

Inherent safe design of advanced high temperature reactors - concepts for future nuclear power plants

International Nuclear Information System (INIS)

Hodzic, A.; Kugeler, K.

1997-01-01

This paper discusses the applicable solutions for a commercial size High Temperature Reactor (HTR) with inherent safety features. It describes the possible realization using an advanced concept which combines newly proposed design characteristics with some well known and proven HTR inherent safety features. The use of the HTR technology offers the conceivably best solution to meet the legal criteria, recently stated in Germany, for the future reactor generation. Both systems, block and pebble bed ,reactor, could be under certain design conditions self regulating in terms of core nuclear heat, mechanical stability and the environmental transfer. 23 refs., 7 figs

Strengths, weaknesses, opportunities and threats for HTR deployment in Europe

International Nuclear Information System (INIS)

Bredimas, Alexandre; Kugeler, Kurt; Fütterer, Michael A.

2014-01-01

High temperature nuclear reactors are a technology, of which early versions were demonstrated in the 1960s–1980s in Germany (AVR, THTR) and the United States (Peach Bottom, Fort St. Vrain). HTRs were initially designed for high temperature, high efficiency electricity generation but the technology, the market and the targeted applications have evolved since then to address industrial cogeneration and new operational conditions (in particular new safety regulations). This paper intends to analyse the latest status of HTR today, as regards their intrinsic strengths and weaknesses and their external context, whether positive (opportunities) or negative (threats). Different dimensions are covered by the analysis: technology status, results from R and D programmes (especially in Europe), competences and skills, licensing aspects, experience feedback from demonstrator operation (in particular in Germany), economic conditions and other non-technical aspects. Europe has a comprehensive experience in the field of HTR with capabilities in both pebble bed and prismatic designs (R and D, engineering, manufacturing, operation, dismantling, and the full fuel cycle). Europe is also a promising market for HTR as the process heat market is large with good industrial and cogeneration infrastructures. The analysis of the European situation is to a good deal indicative for the global potential of this technology

Analysis the Response Function of the HTR Ex-core Neutron Detectors in Different Core Status

International Nuclear Information System (INIS)

Fan Kai; Li Fu; Zhou Xuhua

2014-01-01

Modular high temperature gas cooled reactor HTR-PM demonstration plant, designed by INET, Tsinghua University, is being built in Shidao Bay, Shandong province, China. HTR-PM adopts pebble bed concept. The harmonic synthesis method has been developed to reconstruct the power distributions on HTR-PM. The method based on the assumption that the neutron detector readings are mainly determined by the status of the core through the power distribution, and the response functions changed little when the status of the core changed. To verify the assumption, the influence factors to the ex-core neutron detectors are calculated in this paper, including the control rod position and the temperature of the core. The results shows that when the status of the core changed, the power distribution changed more remarkable than the response function, but the detector readings could change about 5% because of the response function changing. (author)

French programme for HTR fuel

International Nuclear Information System (INIS)

Gillet, R.M.

1991-01-01

It is reported that in the frameworks of the French HTR research program, stopped in 1979 the HTR coated particle fuel, fuel rod and prismatic fuel element design have been successfully developed and irradiation tested in France and specific examination methods for irradiated fuel particles, rods and graphite blocks have been developed. Currently CEA is involved in fission product transport experiments sponsored by the US Department of Energy and performed in the COMEDIE loop. Finally the CEA follows progress and developments in HTR fuel research and development throughout the world. 1 tab

Waste heat of HTR power stations for district heating

International Nuclear Information System (INIS)

Bonnenberg, H.; Schlenker, H.V.

1975-01-01

The market situation, the applied techniques, and the transport, for district heating in combination with HTR plants are considered. Analysis of the heat market indicates a high demand for heat at temperatures between 100 and 150 0 C in household and industry. This market for district heating can be supplied by heat generated in HTR plants using two methods: (1) the combined heat and power generation in steam cycle plants by extracting steam from the turbine, and (2) the use of waste heat of a closed gas turbine cycle. The heat generation costs of (2) are negligible. The cost for transportation of heat over the average distance between existing plant sites and consumer regions (25 km) are between 10 and 20% of the total heat price, considering the high heat output of nuclear power stations. Comparing the price of heat gained by use of waste heat in HTR plants with that of conventional methods, considerable advantages are indicated for the combined heat and power generation in HTR plants. (author)

Gas reactor and associated nuclear experience in the UK relevant to high temperature reactor engineering

International Nuclear Information System (INIS)

Beech, D.J.; May, R.

2000-01-01

In the UK, the NNC played a leading role in the design and build of all of the UK's commercial magnox reactors and advanced gas-cooled reactors (AGRs). It was also involved in the DRAGON project and was responsible for producing designs for large scale HTRs and other gas reactor designs employing helium and carbon dioxide coolants. This paper addresses the gas reactor experience and its relevance to the current HTR designs under development which use helium as the coolant, through the consideration of a representative sample of the issues addressed in the UK by the NNC in support of the AGR and other reactor programmes. Modern HTR designs provide unique engineering challenges. The success of the AGR design, reflected in the extended lifetimes agreed upon by the licensing authorities at many stations, indicates that these challenges can be successfully overcome. The UK experience is unique and provides substantial support to future gas reactor and high temperature engineering studies. (authors)

Temperature coefficients in the Dragon low-enriched power reactor

Energy Technology Data Exchange (ETDEWEB)

Hansen, U

1972-05-15

The temperature coefficient of the fuel and of the moderator have been evaluated for the Dragon HTR design for different stages in reactor life, initial core, end of no-refuelling period and equilibrium conditions. The investigation has shown the low-enriched HTR to have a strong, positive moderator coefficient. In some cases and for special operating conditions, even leading to a positive total temperature coefficient. This does not imply, however, that the HTR is an unsafe reactor system. By adequate design of the control system, safe and reliable operating characteristics can be achieved. This has already been proved satisfactory through many years of operation of other graphite moderated systems, such as the Magnox stations.

HTR-500 - a technical and engineered safeguards concept

International Nuclear Information System (INIS)

Schoening, J.; Wachholz, W.; Stoelzl, D.

1985-01-01

The plant succeeding the THTR-300 nuclear power plant, which has just started its trial phase of power operation, is the HTR-500. On behalf of the Arbeitsgemeinschaft Hochtemperaturreaktor (AHR), the BBC/HRB Group completed a preliminary project study of a nuclear power plant equipped with a high temperature reactor in the 500 MW power range, in which the changed requirements in the nuclear power market are taken into account and electricity generating costs are to be achieved which are competitive with those of a 1230 MW convoy pressurized water reactor of the present design. On this basis, construction documents are to be drafted, and the licensing procedure under the Atomic Energy Act is to be carried out, within a planning phase of roughly four years. (orig.) [de

HTR Development in China

International Nuclear Information System (INIS)

Wang Dazhong

2014-01-01

The roles of HTRs in China: 1. Due to the inherent safety features, high efficiency of electricity generation, site flexibility, the modular HTR can act as a supplement to LWR for small and medium size power generation. 2. Co-generation to supply steam up to 600℃, for petroleum refinery, oil sand and oil shale processing, sea water desalination and district heating, etc. 3. Hydrogen production at 900~1000 ℃ by V/HTR. Conclusions and prospects: • China’s energy system will experience transition and reform in the future; • Nuclear energy will play an irreplaceable role in China’s energy development; • Due to the excellent features of inherent safety, the HTR is a promising technology for electricity generation and process heat utilization; • Further international cooperation and exchanges need to be enhanced

Validation of SCALE for High Temperature Gas-Cooled Reactors Analysis

Energy Technology Data Exchange (ETDEWEB)

Ilas, Germina [ORNL; Ilas, Dan [ORNL; Kelly, Ryan P [ORNL; Sunny, Eva E [ORNL

2012-08-01

This report documents verification and validation studies carried out to assess the performance of the SCALE code system methods and nuclear data for modeling and analysis of High Temperature Gas-Cooled Reactor (HTGR) configurations. Validation data were available from the International Handbook of Evaluated Reactor Physics Benchmark Experiments (IRPhE Handbook), prepared by the International Reactor Physics Experiment Evaluation Project, for two different HTGR designs: prismatic and pebble bed. SCALE models have been developed for HTTR, a prismatic fuel design reactor operated in Japan and HTR-10, a pebble bed reactor operated in China. The models were based on benchmark specifications included in the 2009, 2010, and 2011 releases of the IRPhE Handbook. SCALE models for the HTR-PROTEUS pebble bed configuration at the PROTEUS critical facility in Switzerland have also been developed, based on benchmark specifications included in a 2009 IRPhE draft benchmark. The development of the SCALE models has involved a series of investigations to identify particular issues associated with modeling the physics of HTGRs and to understand and quantify the effect of particular modeling assumptions on calculation-to-experiment comparisons.

Experimental Study of Fuel Element Motion in HTR-PM Conveying Pipelines

International Nuclear Information System (INIS)

Wang Xin; Zhang Haiquan; Nie Junfeng; Li Hongke; Liu Jiguo; He Ayada

2014-01-01

The motion action of sphere fuel element (FE) inside fuel pipelines in HTR-PM is indeterminate. Fuel motion is closely connected with the interaction of FE and inner surface of fuel conveying pipe. In this paper, motion method of fuel elements in its conveying pipe is Experimental studied. Combined with the measurement of the fuel passing speed in stainless steel pipe and the track left by sphere ball for experiment, interaction modes of fuel and inner-surface of pipe, which is sliding friction, rolling friction and Collision, has been found. The modes of interaction can affect the speed of fuel conveying, amount of sphere waste and operation stability of fuel handling of high temperature reactor-pebble bed modules (HTR-PM). Furthermore, the motion process of fuel passing a big-elbow which is lying on the top of fuel pneumatic hoisting pipe were experimented. The result shows that the speed before and the speed after the elbow is positive correlation. But with the increase of speed before the elbow, the speed after the elbow increase less. Meanwhile the fuel conveying mode changes from friction to collision. And the conveying process is still steady. The effect can be used to controlling the speed of fuel conveying in fuel handling process of HTR-PM. (author)

Nuclear Safeguards Considerations For The Pebble Bed Modular Reactor (PBMR)

Energy Technology Data Exchange (ETDEWEB)

Phillip Casey Durst; David Beddingfield; Brian Boyer; Robert Bean; Michael Collins; Michael Ehinger; David Hanks; David L. Moses; Lee Refalo

2009-10-01

High temperature reactors (HTRs) have been considered since the 1940s, and have been constructed and demonstrated in the United Kingdom (Dragon), United States (Peach Bottom and Fort Saint Vrain), Japan (HTTR), Germany (AVR and THTR-300), and have been the subject of conceptual studies in Russia (VGM). The attraction to these reactors is that they can use a variety of reactor fuels, including abundant thorium, which upon reprocessing of the spent fuel can produce fissile U-233. Hence, they could extend the stocks of available uranium, provided the fuel is reprocessed. Another attractive attribute is that HTRs typically operate at a much higher temperature than conventional light water reactors (LWRs), because of the use of pyrolytic carbon and silicon carbide coated (TRISO) fuel particles embedded in ceramic graphite. Rather than simply discharge most of the unused heat from the working fluid in the power plant to the environment, engineers have been designing reactors for 40 years to recover this heat and make it available for district heating or chemical conversion plants. Demonstrating high-temperature nuclear energy conversion was the purpose behind Fort Saint Vrain in the United States, THTR-300 in Germany, HTTR in Japan, and HTR-10 and HTR-PM, being built in China. This resulted in nuclear reactors at least 30% or more thermodynamically efficient than conventional LWRs, especially if the waste heat can be effectively utilized in chemical processing plants. A modern variant of high temperature reactors is the Pebble Bed Modular Reactor (PBMR). Originally developed in the United States and Germany, it is now being redesigned and marketed by the Republic of South Africa and China. The team examined historical high temperature and high temperature gas reactors (HTR and HTGR) and reviewed safeguards considerations for this reactor. The following is a preliminary report on this topic prepared under the ASA-100 Advanced Safeguards Project in support of the NNSA Next

Development of Chinese HTR-PM pebble bed equivalent conductivity test facility

Energy Technology Data Exchange (ETDEWEB)

Ren, Cheng; Yang, Xingtuan; Jiang, Shengyao [Tsinghua Univ., Beijing (China). Inst. of Nuclear and New Energy Technology

2016-01-15

The first two 250-MWt high-temperature reactor pebble bed modules (HTR-PM) have been installing at the Shidaowan plant in Shandong Province, China. The values of the effective thermal conductivity of the pebble bed core are essential parameters for the design. For their determination, Tsinghua University in China has proposed a full-scale heat transfer experiment to conduct comprehensive thermal transfer tests in packed pebble bed and to determine the effective thermal conductivity.

Burning minor actinides in a HTR energy spectrum

International Nuclear Information System (INIS)

Pohl, Christoph; Rütten, H. Jochem

2012-01-01

Highlights: ► Burn-up analysis for varying plutonium/minor actinide fuel compositions. ► The influence of varying heavy metal fuel element loads is investigated. ► Significant burn-up via radiative capture and subsequently fission is observed. ► Difference observed between fuel element burn-up and total actinide burning rate. - Abstract: The generation of nuclear energy by means of the existing nuclear reactor systems is based mainly on the fission of U-235. But this comes along with the capture of neutrons by the U-238 faction and results in a build-up of plutonium isotopes and minor actinides as neptunium, americium and curium. These actinides are dominant for the long time assessment of the radiological risk of a final disposal therefore a minimization of the long living isotopes is aspired. Burning the actinides in a high temperature helium cooled graphite moderated reactor (HTR) is one of these options. The use of plutonium isotopes to sustain the criticality of the system is intended to avoid on the one hand highly enriched uranium because of international regulations and on the other hand low enriched uranium because of the build up of new actinides from neutron capture in the U-238 fraction. Because initial minor actinide isotopes are typically not fissionable by thermal neutrons the idea is to fission instead the intermediate isotopes generated by the first neutron capture. This paper comprises calculations for plutonium/minor actinides/thorium fuel compositions and their correlated final burn-up for a generic pebble bed HTR based on the reference design of the 400 MW PBMR. In particular the cross sections and the neutron balance of the different minor actinide isotopes in the higher thermal energy spectrum of a HTR will be discussed. For a fuel mixture of plutonium and minor actinides a significant burn-up of these actinides up to 20% can be achieved but at the expense of a higher residual fraction of plutonium in the burned fuel. Combining

Digital Distributed Control System Design: Control Policy for Shared Objects in HTR-PM

International Nuclear Information System (INIS)

Zhou Shuqiao; Huang Xiaojin

2014-01-01

HTR-PM is an HTR demonstration plant with a structure of two modules feeding one steam turbine. Compared with the structure of one single reactor feeding one turbine, there are more devices shared between these two modules. When they are operated, the shared components are prone to introduce collisions or even logical deadlocks for different technical processes. The future commercial HTR-PM plants are supposed to comprise more modules for a larger turbine, thus the collision problem introduced by the shared components may become severer. Therefore, how to design suitable policies in the distributed control system (DCS) to relieve the collisions during using these shared devices is a new and also a very important problem. In this paper, the classifications of the shared devices are first addressed, and then how to identify the shared objects of an NPP is proposed. Furthermore, a general model for the control logic design is proposed, taking into consideration the collision avoidance, time delay and fairness. The example of how to apply the schemes to relieve the conflicts and deadlocks in the processes of using the shared devices in fuel element cycling system is illustrated. (author)

Pre-economic analysis of HTR in preparation for a comprehensive economic assessment of HTRs in the world

Energy Technology Data Exchange (ETDEWEB)

Bredimas, Alexandre, E-mail: alexandre.bredimas@strane-innovation.com

2014-05-01

High temperature nuclear reactors will address mainly the industrial cogeneration market and compete with gas cogeneration, the current reference technology. The key question for HTR is therefore: how far are HTRs competitive against gas technologies? This simple question demands a complex response. First, the cogeneration scheme has to be discussed according the specificities in heat usage of every industry as they will impact the design. Second, the costs, revenues and risks of the different lifecycle phases for both a HTR and gas cogeneration plant have to be assessed and compared. These parameters will greatly depend on each location (personnel costs, gas local prices, CO{sub 2} pricing, etc.). A particular attention has to be given to the risk interactions between the cogeneration plant and the industrial facility it is supplying with heat and electricity (e.g. tritium contamination in industrial processes, explosion of flammable products in industrial site). This paper aims mainly at starting exchanges at international level with other equivalent initiatives in order to assess in general terms the economic viability of HTR worldwide, in relation to the evaluation of the HTR global market.

Pre-economic analysis of HTR in preparation for a comprehensive economic assessment of HTRs in the world

International Nuclear Information System (INIS)

Bredimas, Alexandre

2014-01-01

High temperature nuclear reactors will address mainly the industrial cogeneration market and compete with gas cogeneration, the current reference technology. The key question for HTR is therefore: how far are HTRs competitive against gas technologies? This simple question demands a complex response. First, the cogeneration scheme has to be discussed according the specificities in heat usage of every industry as they will impact the design. Second, the costs, revenues and risks of the different lifecycle phases for both a HTR and gas cogeneration plant have to be assessed and compared. These parameters will greatly depend on each location (personnel costs, gas local prices, CO 2 pricing, etc.). A particular attention has to be given to the risk interactions between the cogeneration plant and the industrial facility it is supplying with heat and electricity (e.g. tritium contamination in industrial processes, explosion of flammable products in industrial site). This paper aims mainly at starting exchanges at international level with other equivalent initiatives in order to assess in general terms the economic viability of HTR worldwide, in relation to the evaluation of the HTR global market

Reactor physics and reactor strategy investigations into the fissionable material economy of the thorium and uranium cycle in fast breeder reactors and high temperature reactors

International Nuclear Information System (INIS)

Schikorr, W.M.

In this work the properties governing the fissionable material economy of the uranium and thorium cycles are investigated for the advanced reactor types currently under development - the fast breeder reactor (FBR) and the high temperature reactor (HTR) - from the point of view of the optimum utilization of the available nuclear fuel reserves and the continuance of supply of these reserves. For this purpose, the two reactor types are first of all considered individually and are subsequently discussed as a complementary overall system

Needs in Research and Development on materials for the gas coolant nuclear system: HTR/VHTR and GFR; Besoins en R et D sur les materiaux pour les systemes nucleaires a caloporteur gaz: HTR/VHTR et GFR

Energy Technology Data Exchange (ETDEWEB)

Billot, Ph. [CEA Saclay, Dir. du Developpement et de l' Innovation Nucleares (DEN/DDIN), 91 - Gif Sur Yvette (France)

2003-07-01

This presentation takes stock on the materials for high temperature reactors HTR (850 C), very high temperature VHTR(>1000 C) and fast neutrons high temperature GGF(850 C). It concerns the welding materials for the vessel, Ni-based superalloys for gas turbines, coatings, graphite, ceramics and corrosion studies. (A.L.B.)

Status on potential of advanced fission reactors

International Nuclear Information System (INIS)

L-Zaleski, C.P.

1978-01-01

In this short lecture, only two types of reactors will be discussed: the liquid metal fast breeder reactors (LMFBR) and the high temperature reactors (HTR). This does not mean that other very interesting concepts do not exist, but there are or proven light water reactors and heavy water reactors or has not reached the state of industrial development like molten-salt or gas breeder reactors. In discussing any types of industrial development, it seems to me useful, first to indicate the reasons or motivations for this development. Then I will give a short historical review and analysis of what has been done up to now. For HTR's a very brief status report will be presented. For LMFBR's, I will give indications of experience gained with demonstration plants and more specifically with Phenix, before listing the most important technical problems which still need more work to be fully solved. Finally, I will briefly discuss the economic status and perspectives of LMFBR's and will mention the public acceptance problem

High-temperature reactor developments in the Netherlands

International Nuclear Information System (INIS)

Schram, R.P.C.; Cordfunke, E.H.P.; Heek, A.I. van.

1996-01-01

The high-temperature reactor development in the Netherland is embedded in the WHITE reactor program, in which several Dutch research institutes and engineering companies participate. The activities within the WHITE program are focused on the development of a small scale HTS for combined heat and power generation. In 1995, design choices for a pebble bed reactor were made at ECN. The first concept HTR will gave a closed cycle helium turbine and a power level of 40 MWth. It is intended to make the market introduction of a commercially competitive HTR feasible. The design will be an optimization of the Peu-a-Peu (PAP) concept of KFA Juelich. Computer codes necessary for the evaluation of reactor physics aspects of this reactor are developed in cooperation with international partners. An evaluation of a 20 MWth PAP concept showed that the maximum fuel termmperature after depressurization does not exceed 1300 C. (orig.)

The Hitrex Programme: unperturbed HTR lattice and control rod measurements

Energy Technology Data Exchange (ETDEWEB)

Beynon, A J; Nunn, D L

1972-06-15

Reactivity, power distributions, plutonium production and fast neutron graphite damage are being studied at Berkeley Nuclear Laboratories (BNL) on the HTR 'Hitrex' reactor under cold clean conditions. Rod interactions, important in assessing local criticality hazards, are receiving special attention in the measurements. The proposals for the first two series of measurements on Hitrex are discussed in this note, Hitrex 1a being the unperturbed reactor, and Hitrex 1b the same fuel array but with a number of different control absorber loadings in it. Common to both series will be cross pin, cross block and cross core measurements of power rating, thermal spectrum and damage dose distributions, so that these will be known as functions of the fuel, reflector and absorber environment.

For a Global HTR Marketing Initiative

International Nuclear Information System (INIS)

Bredimas, Alexandre; Venneri, Francesco; Richards, Matthew

2014-01-01

HTRs are at a crossroads in their history. The technology is proven and the current technical developments relatively mastered but the marketing track record is disappointing. This paper comes to the conclusion that an international, collaborative marketing and communication plan must be implemented in order to address the marketing bottleneck of HTRs. The paper reflects about the HTR product specificities, its unique selling points and its positioning against other nuclear designs and gas cogeneration. It summarises the global market status and demonstrates that the global market for HTRs is there, for electricity generation, industrial cogeneration and polygeneration. The paper finally argues that HTR vendors have a shared interest to unite in order to succeed in activating the market demand for HTR, and suggests an action plan for an international collaboration among HTR vendors to market and communicate globally on HTRs and reach together a critical mass of business leads worldwide, a mutually beneficial outcome. (author)

Reactor safety research and safety technology. Pt. 2

International Nuclear Information System (INIS)

Theenhaus, R.; Wolters, J.

1987-01-01

The state of HTR safety research work reached permits a comprehensive and reliable answer to be given to questions which have been raised by the reactor accident at Chernobyl, regarding HTR safety. Together with the probability safety analyses, the way to a safety concept suitable for an HTR is cleared; instructions are given for design optimisation with regard to safety technique and economy. The consequences of a graphite fire, the neutron physics design and the consequenes of the lack of a safety containment are briefly described. (DG) [de

The HTR-PM Plant Full Scope Training Simulator

International Nuclear Information System (INIS)

Wang Junsan; Wang Yuding; Zhou Shuyong; Cai Ruizhong; Cao Jianting

2014-01-01

This paper describes the technical aspects of the Full Scope Training Simulator developed for HTR-PM Plant in Shidao Bay, Shandong Province, China. An overview of the HTR-PM plant and simulator structure is presented. The models developed for the simulator are discussed in detail. Some important verification tests have been conducted on the HTR-PM Plant Training Simulator. (author)

Development of a method for high temperature reactor calculations tested at the critical facility Kahter using the program system RSYST. Entwicklung einer Rechenmethode zur HTR-Auslegung im Rahmen des Programmsystems RSYST und deren Erprobung an der kritischen Anlage 'Kahter'

Energy Technology Data Exchange (ETDEWEB)

Nabi, R

1979-08-15

In this report the neutron- and reactor physical aspects of the high temperature pebble bed reactor are studied. For this purpose appropriate HTR-nuclear data sets are generated and applied in a calculation model, which is developed on the basis of neutron transport and diffusion theory. This model includes the complete reactor calculation for determination of neutron flux, reactivity and reaction rates. This reactor calculation is based on following: evaluation of resonance absorption in double heterogeneity, cell calculation in spherical geometry, zone spectral calculation and subsequent 2-dimensional diffusion calculation. All calculations are performed in the modular program system RSYST, which accommodates simplified treatment of reactor physics problems through its data transfer and treatment techniques and through its calculations control features. In this report the neutron- and reactor physical aspects of the high temperature pebble bed reactor are studied. For this purpose appropriate HTR-nuclear data sets are generated and applied in a calculation model, which is developed on the basis of neutron transport and diffusion theory. This model includes the complete reactor calculation for determination of neutron flux, reactivity and reaction rates. This reactor calculation is based on following: evaluation of resonance absorption in double heterogeneity, cell calculation in spherical geometry, zone spectral calculation and subsequent 2-dimensional diffusion calculation. All calculations are performed in the modular program system RSYST, which accommodates simplified treatment of reactor physics problems through its data transfer and treatment techniques and through its calculations control features. The results of the calculations are compared with measured values of different core configurations of the critical facility for the high temperature pebble bed reactor (KAHTER). This comparison shows how a critical facility is used to verify and to adjust

Research on vibration properties of auxiliary bearing cage used in HTR-10 GT project

International Nuclear Information System (INIS)

Qin Qingquan; Yang Guojun; Shi Zhengang; Yu Suyuan

2009-01-01

Auxiliary Bearings (ABs) is one of the most important parts in Active Magnetic Bearing (AMB) system, which was used in HTR-10 GT project. This paper uses finite element method to analyze the centrifugal stress and free vibration properties of the cage according to its work condition. And different geometric parameters of the cage that has effects on its vibration performance are discussed. The results show that the highest centrifugal stress is in the middle of the cage side sill. The low odder vibration modes of the cage can be induced when the auxiliary bearings are working. Proper geometric parameters and ball pocket number can enhance the performance of the cage. (authors)

The Energy Conversion Analysis of HTR Gas Turbine System

International Nuclear Information System (INIS)

Utaja

2000-01-01

The energy conversion analysis of HTR gas turbine system by hand calculation is tedious work and need much time. This difficulty comes from the repeated thermodynamic process calculation, both on compression or expansion of the cycle. To make the analysis faster and wider variable analyzed, HTR-1 programme is used. In this paper, the energy conversion analysis of HTR gas turbine system by HTR-1 will be described. The result is displayed as efficiency curve and block diagram with the input and output temperature of the component. This HTR-1 programme is developed by Basic language programming and be compiled by Visual Basic 5.0 . By this HTR-1 programme, the efficiency, specific power and effective compression of the amount of gas can be recognized fast. For example, for CO 2 gas between 40 o C and 700 o C, the compression on maximum efficiency is 4.6 and the energy specific is 18.9 kcal/kg, while the temperature changing on input and output of the component can be traced on monitor. This process take less than one second, while the manual calculation take more than one hour. It can be concluded, that the energy conversion analysis of the HTR gas turbine system by HTR-1 can be done faster and more variable analyzed. (author)

Structural and Functional Analysis of Human HtrA3 Protease and Its Subdomains.

Directory of Open Access Journals (Sweden)

Przemyslaw Glaza

Full Text Available Human HtrA3 protease, which induces mitochondria-mediated apoptosis, can be a tumor suppressor and a potential therapeutic target in the treatment of cancer. However, there is little information about its structure and biochemical properties. HtrA3 is composed of an N-terminal domain not required for proteolytic activity, a central serine protease domain and a C-terminal PDZ domain. HtrA3S, its short natural isoform, lacks the PDZ domain which is substituted by a stretch of 7 C-terminal amino acid residues, unique for this isoform. This paper presents the crystal structure of the HtrA3 protease domain together with the PDZ domain (ΔN-HtrA3, showing that the protein forms a trimer whose protease domains are similar to those of human HtrA1 and HtrA2. The ΔN-HtrA3 PDZ domains are placed in a position intermediate between that in the flat saucer-like HtrA1 SAXS structure and the compact pyramidal HtrA2 X-ray structure. The PDZ domain interacts closely with the LB loop of the protease domain in a way not found in other human HtrAs. ΔN-HtrA3 with the PDZ removed (ΔN-HtrA3-ΔPDZ and an N-terminally truncated HtrA3S (ΔN-HtrA3S were fully active at a wide range of temperatures and their substrate affinity was not impaired. This indicates that the PDZ domain is dispensable for HtrA3 activity. As determined by size exclusion chromatography, ΔN-HtrA3 formed stable trimers while both ΔN-HtrA3-ΔPDZ and ΔN-HtrA3S were monomeric. This suggests that the presence of the PDZ domain, unlike in HtrA1 and HtrA2, influences HtrA3 trimer formation. The unique C-terminal sequence of ΔN-HtrA3S appeared to have little effect on activity and oligomerization. Additionally, we examined the cleavage specificity of ΔN-HtrA3. Results reported in this paper provide new insights into the structure and function of ΔN-HtrA3, which seems to have a unique combination of features among human HtrA proteases.

Structural and Functional Analysis of Human HtrA3 Protease and Its Subdomains.

Science.gov (United States)

Glaza, Przemyslaw; Osipiuk, Jerzy; Wenta, Tomasz; Zurawa-Janicka, Dorota; Jarzab, Miroslaw; Lesner, Adam; Banecki, Bogdan; Skorko-Glonek, Joanna; Joachimiak, Andrzej; Lipinska, Barbara

2015-01-01

Human HtrA3 protease, which induces mitochondria-mediated apoptosis, can be a tumor suppressor and a potential therapeutic target in the treatment of cancer. However, there is little information about its structure and biochemical properties. HtrA3 is composed of an N-terminal domain not required for proteolytic activity, a central serine protease domain and a C-terminal PDZ domain. HtrA3S, its short natural isoform, lacks the PDZ domain which is substituted by a stretch of 7 C-terminal amino acid residues, unique for this isoform. This paper presents the crystal structure of the HtrA3 protease domain together with the PDZ domain (ΔN-HtrA3), showing that the protein forms a trimer whose protease domains are similar to those of human HtrA1 and HtrA2. The ΔN-HtrA3 PDZ domains are placed in a position intermediate between that in the flat saucer-like HtrA1 SAXS structure and the compact pyramidal HtrA2 X-ray structure. The PDZ domain interacts closely with the LB loop of the protease domain in a way not found in other human HtrAs. ΔN-HtrA3 with the PDZ removed (ΔN-HtrA3-ΔPDZ) and an N-terminally truncated HtrA3S (ΔN-HtrA3S) were fully active at a wide range of temperatures and their substrate affinity was not impaired. This indicates that the PDZ domain is dispensable for HtrA3 activity. As determined by size exclusion chromatography, ΔN-HtrA3 formed stable trimers while both ΔN-HtrA3-ΔPDZ and ΔN-HtrA3S were monomeric. This suggests that the presence of the PDZ domain, unlike in HtrA1 and HtrA2, influences HtrA3 trimer formation. The unique C-terminal sequence of ΔN-HtrA3S appeared to have little effect on activity and oligomerization. Additionally, we examined the cleavage specificity of ΔN-HtrA3. Results reported in this paper provide new insights into the structure and function of ΔN-HtrA3, which seems to have a unique combination of features among human HtrA proteases.

Research activities on high-temperature gas-cooled reactors (HTRs) in the 5. EURATOM RTD Framework programme

International Nuclear Information System (INIS)

Martin-Bermejo, J.; Hugon, M.; Van Goethem, G.

2002-01-01

One of the areas of research of the 'nuclear fission' key action of the 5. EURATOM RTD Framework Programme (FP5) is the safety and efficiency of future systems. The main objective of this area is to investigate and evaluate new or revisited concepts (both reactors and alternative fuels) for nuclear energy that offer potential longer term benefits in terms of cost, safety, waste management, use of fissile material, less risk of diversion and sustainability. Several projects related to high-temperature gas-cooled reactors (HTRs) were retained by the European Commission (EC) services. They address important issues such as HTR fuel technology, HTR fuel cycle, HTR materials, power conversion systems and licensing. Most of these projects have already started and are progressing according to the schedule. They are the initial core of activities of a European Network on 'High-temperature Reactor Technology' (HTR-TN) recently set up by 18 EU organisations. (authors)

Pu and MA Management in Thermal HTR, QUO VADIS? Insights from the Euratom PUMA project

International Nuclear Information System (INIS)

Kuijper, J.C.

2013-01-01

The results of this study demonstrate the excellent plutonium and minor actinide burning capabilities of the high temperature reactor. The largest degree of incineration is attained in the case of an HTR fuelled by pure plutonium fuel as it remains critical at very deep burn-up of the discharged pebbles. Addition of minor actinides to the fuel leads to decrease of the achievable discharge burn-up and therefore smaller fraction of actinides incinerated during reactor operation. The inert-matrix fuel design improves the transmutation performance of the reactor, while the “wallpaper” fuel does not have advantage over the standard fuel design in this respect

A Statistical Analysis on the Coating Layer Thicknesses of a TRISO of 350 MWth Block-type HTR

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Min; Jo, C. K.; Cho, M. S. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

A tri-isotropic coated fuel particle (TRISO) is a basic fuel element of a high temperature reactor (HTR). The block-type HTR fuel is a cylindrical graphite compact in which a large number of TRISOs are embedded. There are more than 11 billion TRISOs in a 350 MW{sub th} block-type HTR core. Among the RSM quadratic models, the BBD model produces the smallest errors at both interior and exterior points. The errors in the quadratic model of the small-type CCD is the biggest, particularly at exterior points. The CCD has a disadvantage of generating a number of decimal places in its factor levels because of its axial points. It is recommended to use the BBD or the full-type CCD with an adjusted axial point which does not produce the decimal places in its factor levels. More general statistical model for a TRISO design will be secured when the number of factors and responses increases. This study treats a statistical analysis on the optimal layer thicknesses of a UCO TRISO of 350 MW{sub th} block-type HTR which cause a minimum tangential stress to act on the SiC layer. Three response surface methods (RSMs) are used as statistical methods and their resulting quadratic models are compared.

A Statistical Analysis on the Coating Layer Thicknesses of a TRISO of 350 MWth Block-type HTR

International Nuclear Information System (INIS)

Kim, Young Min; Jo, C. K.; Cho, M. S.

2016-01-01

A tri-isotropic coated fuel particle (TRISO) is a basic fuel element of a high temperature reactor (HTR). The block-type HTR fuel is a cylindrical graphite compact in which a large number of TRISOs are embedded. There are more than 11 billion TRISOs in a 350 MW_t_h block-type HTR core. Among the RSM quadratic models, the BBD model produces the smallest errors at both interior and exterior points. The errors in the quadratic model of the small-type CCD is the biggest, particularly at exterior points. The CCD has a disadvantage of generating a number of decimal places in its factor levels because of its axial points. It is recommended to use the BBD or the full-type CCD with an adjusted axial point which does not produce the decimal places in its factor levels. More general statistical model for a TRISO design will be secured when the number of factors and responses increases. This study treats a statistical analysis on the optimal layer thicknesses of a UCO TRISO of 350 MW_t_h block-type HTR which cause a minimum tangential stress to act on the SiC layer. Three response surface methods (RSMs) are used as statistical methods and their resulting quadratic models are compared

Needs in Research and Development on materials for the gas coolant nuclear system: HTR/VHTR and GFR

International Nuclear Information System (INIS)

Billot, Ph.

2003-01-01

This presentation takes stock on the materials for high temperature reactors HTR (850 C), very high temperature VHTR(>1000 C) and fast neutrons high temperature GGF(850 C). It concerns the welding materials for the vessel, Ni-based superalloys for gas turbines, coatings, graphite, ceramics and corrosion studies. (A.L.B.)

Probabilistic safety assessment framework of pebble-bed modular high-temperature gas-cooled reactor

International Nuclear Information System (INIS)

Liu Tao; Tong Jiejuan; Zhao Jun; Cao Jianzhu; Zhang Liguo

2009-01-01

After an investigation of similar reactor type probabilistic safety assessment (PSA) framework, Pebble-bed Modular High-Temperature Gas-cooled Reactor (HTR-PM) PSA framework was presented in correlate with its own design characteristics. That is an integral framework which spreads through event sequence structure with initiating events at the beginning and source term categories in the end. The analysis shows that it is HTR-PM design feature that determines its PSA framework. (authors)

High temperature reactor module power plant. Plant and safety concept June 1986 - 38.07126.2

International Nuclear Information System (INIS)

1986-06-01

The modular HTR power plant is a universally applicable energy source for the co-generation of electricity, process steam or district heating. The modular HTR concept is characterized by the fact that standardized reactor units with power ratings of 200 MJ/s (so-called modules) can be combined to form power plants with a higher power rating. Consequently the special safety features of small high-temperature reactors (HTR) are also available at higher power plant ratings. The safety features, the technical design and the mode of operation are briefly described in the following, taking a power plant with two HTR-Modules for the co-generation of electricity and process steam as an example. Due to its universal applicability and excellent safety features, the modular HTR power plant is suitable for erection on any site, but particularly on sites near other industrial plants or in densely populated areas. The co-generation of electricity and process steam or district heating with a modular HTR power plant as described here is primarily tailored to the requirements of industrial and communal consumers. The site for such a plant is a typical industrial one. The anticipated features of such sites were taken into consideration in the design of the modular HTR power plant

High temperature reactor module power plant. Plant and safety concept June 1986 - 38.07126.2

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-06-15

The modular HTR power plant is a universally applicable energy source for the co-generation of electricity, process steam or district heating. The modular HTR concept is characterized by the fact that standardized reactor units with power ratings of 200 MJ/s (so-called modules) can be combined to form power plants with a higher power rating. Consequently the special safety features of small high-temperature reactors (HTR) are also available at higher power plant ratings. The safety features, the technical design and the mode of operation are briefly described in the following, taking a power plant with two HTR-Modules for the co-generation of electricity and process steam as an example. Due to its universal applicability and excellent safety features, the modular HTR power plant is suitable for erection on any site, but particularly on sites near other industrial plants or in densely populated areas. The co-generation of electricity and process steam or district heating with a modular HTR power plant as described here is primarily tailored to the requirements of industrial and communal consumers. The site for such a plant is a typical industrial one. The anticipated features of such sites were taken into consideration in the design of the modular HTR power plant.

Risk assessment of small-sized HTR with pebble-bed core

International Nuclear Information System (INIS)

Kroeger, W.; Mertens, J.; Wolters, J.

1987-01-01

Two recent concepts of small-sized HTR's (HTR-Modul and HTR-100) were analysed regarding their safety concepts and risk protection. In neither case do core cooling accidents contribute to the risk because of the low induced core temperatures. Water ingress accidents dominate the risk in both cases by detaching deposited fission products which can be released into the environment. For these accident sequences no early fatalities and practically no lethal case of cancer were computed. Both HTR concepts include adequate precautionary measures and an infinitely small risk according to the usual standards. The safety concepts make express use of the specific inherent safety features of pebble-bed HTR's. (orig.)

Study on "1"4C content in post-irradiation graphite spheres of HTR-10

International Nuclear Information System (INIS)

Wang Shouang; Pi Yue; Xie Feng; Li Hong; Cao Jianzhu

2014-01-01

Since the production mechanism of the "1"4C in spherical fuel elements was similar to that of fuel-free graphite spheres, in order to obtain the amount of "1"4C in fuel elements and graphite spheres of HTR-10, the production mechanism of the "1"4C in graphite spheres was studied. The production sources of the "1"4C in graphite spheres and fuel elements were summarized, the amount of "1"4C in the post-irradiation graphite spheres was calculated, the decomposition techniques of graphite spheres were compared, and experimental methods for decomposing the graphite spheres and preparing the "1"4C sample were proposed. The results can lay the foundation for further experimental research and provide theoretical calculations for comparison. (authors)

HTR plus modern turbine technology for higher efficiencies

International Nuclear Information System (INIS)

Barnert, H.; Kugeler, K.

1996-01-01

The recent efficiency race for natural gas fired power plants with gas-plus steam-turbine-cycle, is shortly reviewed. The question 'can the HTR compete with high efficiencies?' is answered: Yes, it can - in principle. The gas-plus steam-turbine cycle, also called combi-cycle, is proposed to be taken into consideration here. A comparative study on the efficiency potential is made; it yields 54.5% at 1,050 deg. C gas turbine-inlet temperature. The mechanisms of release versus temperature in the HTR are summarized from the safety report of the HTR MODUL. A short reference is made to the experiences from the HTR-Helium Turbine Project HHT, which was performed in the Federal Republic of Germany in 1968 to 1981. (author). 8 figs,. 1 tab

HTR plus modern turbine technology for higher efficiencies

Energy Technology Data Exchange (ETDEWEB)

Barnert, H; Kugeler, K [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Sicherheitsforschung und Reaktortechnik

1996-08-01

The recent efficiency race for natural gas fired power plants with gas-plus steam-turbine-cycle, is shortly reviewed. The question `can the HTR compete with high efficiencies?` is answered: Yes, it can - in principle. The gas-plus steam-turbine cycle, also called combi-cycle, is proposed to be taken into consideration here. A comparative study on the efficiency potential is made; it yields 54.5% at 1,050 deg. C gas turbine-inlet temperature. The mechanisms of release versus temperature in the HTR are summarized from the safety report of the HTR MODUL. A short reference is made to the experiences from the HTR-Helium Turbine Project HHT, which was performed in the Federal Republic of Germany in 1968 to 1981. (author). 8 figs,. 1 tab.

The improvement of the method of equivalent cross section in HTR

International Nuclear Information System (INIS)

Guo, J.; Li, F.

2012-01-01

The Method of Equivalence Cross-Sections (MECS) is a combined transport-diffusion method. By appropriately adjusting the diffusion coefficient of homogenized absorber region, the diffusion theory could yield satisfactory results for the full core model with strong neutron absorber material, for example the control rod in High temperature gas cooled reactor (HTR). Original implementation of MECS based on 1-D cell transport model has some limitation on accuracy and applicability, a new implementation of MECS based on 2-D transport model are proposed and tested in this paper. This improvement can extend the MECS to the calculation of twin small absorber ball system which have a non-circular boring in graphite reflector and different radial position. A least-square algorithm for the calculation of equivalent diffusion coefficient is adopted, and special treatment for diffusion coefficient for higher energy group is proposed in the case that absorber is absent. Numerical results to adopt MECS into control rod calculation in HTR are encouraging. However, there are some problems left. (authors)

Development of high temperature gas cooled reactor in China

Energy Technology Data Exchange (ETDEWEB)

Guo, Wentao [Paul Scherrer Institute, Villigen (Switzerland). Dept. of Nuclear Energy and Safety; Schorer, Michael [Swiss Nuclear Forum, Olten (Switzerland)

2018-02-15

High temperature gas cooled reactor (HTGR) is one of the six Generation IV reactor types put forward by Generation IV International Forum (GIF) in 2002. This type of reactor has high outlet temperature. It uses Helium as coolant and graphite as moderator. Pebble fuel and ceramic reactor core are adopted. Inherit safety, good economy, high generating efficiency are the advantages of HTGR. According to the comprehensive evaluation from the international nuclear community, HTGR has already been given the priority to the research and development for commercial use. A demonstration project of the High Temperature Reactor-Pebble-�bed Modules (HTR-PM) in Shidao Bay nuclear power plant in China is under construction. In this paper, the development history of HTGR in China and the current situation of HTR-PM will be introduced. The experiences from China may be taken as a reference by the international nuclear community.

First Study of Helium Gas Purification System as Primary Coolant of Co-Generation Reactor

International Nuclear Information System (INIS)

Piping Supriatna

2009-01-01

The technological progress of NPP Generation-I on 1950’s, Generation-II, Generation-III recently on going, and Generation-IV which will be implemented on next year 2025, concept of nuclear power technology implementation not only for generate electrical energy, but also for other application which called cogeneration reactor. Commonly the type of this reactor is High Temperature Reactor (HTR), which have other capabilities like Hydrogen production, desalination, Enhanced Oil Recovery (EOR), etc. The cogeneration reactor (HTR) produce thermal output higher than commonly Nuclear Power Plant, and need special Heat Exchanger with helium gas as coolant. In order to preserve heat transfer with high efficiency, constant purity of the gas must be maintained as well as possible, especially contamination from its impurities. In this report has been done study for design concept of HTR primary coolant gas purification system, including methodology by sampling He gas from Primary Coolant and purification by using Physical Helium Splitting Membrane. The examination has been designed in physical simulator by using heater as reactor core. The result of study show that the of Primary Coolant Gas Purification System is enable to be implemented on cogeneration reactor. (author)

C.A.S.H. - a transient integrated plant model for a HTR-module power plant. User manual

International Nuclear Information System (INIS)

Biesenbach, R.; Lauer, A.; Struth, S.

1997-07-01

The computer code C.A.S.H. has been developed as an integrated plant model for the HTR-Module reactor, in order to treat safety related questions about this type of power plant which require a detailed numeric simulation of the transient behaviour of the integrated plant. The present report contains the user manual for this plant model. It consists of three parts: In the first part, the code structure and functions, the course of the simulation calculations, and important code parts are described. The second part is devoted to the practical application and explains extensively the handling of the complex code system with several sample calculations. These computing cases comprise load-follow transients and the shutdown procedure of the HTR-Module and are presented and discussed with the full input data, job patterns, and numerous computer graphics. The third part contains the input manual of C.A.S.H. and is rather extensive as it includes the complete inputs of several reactor component computer codes along with the control program of the integrated plant model. (orig./DG) [de

The high-temperature reactor

International Nuclear Information System (INIS)

Kirchner, U.

1991-01-01

The book deals with the development of the German high-temperature reactor (pebble-bed), the design of a prototype plant and its (at least provisional) shut-down in 1989. While there is a lot of material on the HTR's competitor, the fast breeder, literature is very incomplete on HTRs. The author describes HTR's history as a development which was characterised by structural divergencies but not effectively steered and monitored. There was no project-oriented 'community' such as there was for the fast breeder. Also, the new technology was difficult to control there were situations where no one quite knew what was going on. The technical conditions however were not taken as facts but as a basis for interpretation, wishes and reservations. The HTR gives an opportunity to consider the conditions under which large technical projects can be carried out today. (orig.) [de

Transient behaviour of small HTR for cogeneration

International Nuclear Information System (INIS)

Verkerk, E.C.; Van Heek, A.I.

2000-01-01

The Dutch market for combined generation of heat and power identifies a unit size of 40 MW thermal for the conceptual design of a nuclear cogeneration plant. The ACACIA system provides 14 MWe electricity combined with 17 t/h of high temperature steam (220 deg C, 10 bar) with a pebble-bed high temperature reactor directly coupled with a helium compressor and a helium turbine. The design of this small CHP unit that is used for industrial applications is mainly based on a pre-feasibility study in 1996, performed by a joint working group of five Dutch organisations, in which technical feasibility was shown. Thermal hydraulic and reactor physics analyses show favourable control characteristics during normal operation and a benign response to loss of helium coolant and loss of flow conditions. Throughout the response on these highly infrequent conditions, ample margin exists between the highest fuel temperatures and the temperature above which fuel degradation will occur. To come to quantitative statements about the ACACIA transient behaviour, a calculational coupling between the high temperature reactor core analysis code package PANTHER/DIREKT and the thermal hydraulic code RELAP5 for the energy conversion system has been made. This coupling offers a more realistic simulation of the entire system, since it removes the necessity of forcing boundary conditions on the simulation models at the data transfer points. In this paper, the models used for the dynamic components of the energy conversion system are described, and the results of the calculation for two operational transients in order to demonstrate the effects of the interaction between reactor core and its energy conversion system are shown. Several transient cases that are representative as operational transients for an HTR will be discussed, including one representing a load rejection case that shows the functioning of the control system, in particular the bypass valve. Another transient is a load following

Benchmark Evaluation of HTR-PROTEUS Pebble Bed Experimental Program

International Nuclear Information System (INIS)

Bess, John D.; Montierth, Leland; Köberl, Oliver

2014-01-01

Benchmark models were developed to evaluate 11 critical core configurations of the HTR-PROTEUS pebble bed experimental program. Various additional reactor physics measurements were performed as part of this program; currently only a total of 37 absorber rod worth measurements have been evaluated as acceptable benchmark experiments for Cores 4, 9, and 10. Dominant uncertainties in the experimental keff for all core configurations come from uncertainties in the 235 U enrichment of the fuel, impurities in the moderator pebbles, and the density and impurity content of the radial reflector. Calculations of k eff with MCNP5 and ENDF/B-VII.0 neutron nuclear data are greater than the benchmark values but within 1% and also within the 3σ uncertainty, except for Core 4, which is the only randomly packed pebble configuration. Repeated calculations of k eff with MCNP6.1 and ENDF/B-VII.1 are lower than the benchmark values and within 1% (~3σ) except for Cores 5 and 9, which calculate lower than the benchmark eigenvalues within 4σ. The primary difference between the two nuclear data libraries is the adjustment of the absorption cross section of graphite. Simulations of the absorber rod worth measurements are within 3σ of the benchmark experiment values. The complete benchmark evaluation details are available in the 2014 edition of the International Handbook of Evaluated Reactor Physics Benchmark Experiments

High-temperature gas-cooled reactor technology development program. Annual progress report for period ending December 31, 1980

International Nuclear Information System (INIS)

1981-08-01

Research activities are described concerning HTGR chemistry; fueled graphite development; prestressed concrete pressure vessel development; structural materials; HTGR graphite studies; HTR core evaluation; reactor physics; shielding; application and project assessments; and HTR Core Flow Test Loop studies

High-temperature gas-cooled reactor technology development program. Annual progress report for period ending December 31, 1980

Energy Technology Data Exchange (ETDEWEB)

1981-08-01

Research activities are described concerning HTGR chemistry; fueled graphite development; prestressed concrete pressure vessel development; structural materials; HTGR graphite studies; HTR core evaluation; reactor physics; shielding; application and project assessments; and HTR Core Flow Test Loop studies.

Dynamic simulation for scram of high temperature gas-cooled reactor with indirect helium turbine cycle system

International Nuclear Information System (INIS)

Li Wenlong; Xie Heng

2011-01-01

A dynamic analysis code for this system was developed after the mathematical modeling and programming of important equipment of 10 MW High Temperature Gas Cooled Reactor Helium Turbine Power Generation (HTR-10GT), such as reactor core, heat exchanger and turbine-compressor system. A scram accident caused by a 0.1 $ reactivity injection at 5 second was simulated. The results show that the design emergency shutdown plan for this system is safe and reasonable and that the design of bypass valve has a large safety margin. (authors)

High temperature reactor development in the Netherlands

International Nuclear Information System (INIS)

Heek, A.I. van

1996-01-01

This year, some clear design choices have been made in the WHITE Reactor development programme. The activities will be concentrated at the development of a small size pebble bed HTR for combined heat and power production with a closed cycle gas turbine. Objective of the development is threefold: 1. restoring social support; 2. establishing commercial viability after market introduction; and 3. making the market introduction itself feasible, i.e. limited development and first-of-a-kind costs. This design is based on the peu-a-peu design of KFA Juelich and will be optimized. The computer codes necessary for this are being prepared for this work. The dynamic neutronics code PANTHER is being coupled to the thermal hydraulics code THERMIX-DIREKT. For this reactor type, fuel temperatures are maximal in the scenario of depressurization with recriticality. Even for this scenario, fuel temperatures of the 20MWth PAP-GT do not exceed 1300 deg. C, so there should be room for upscaling for economic reasons. On the other hand, it would be convenient to fuel the reactor batchwise instead of continuously, and the use of thorium could be required. These two features may lead to a larger temperature margin. The optimal design must unite these features in the best acceptable way. To gain expertise in calculations on gas cooled graphite moderate reactors, benchmark calculations are being performed in parallel with international partners. Parallel to this, special expertise is being built up on HTR fuel and HTR reactor vessels. (author). 3 refs

Advanced nuclear reactor and nuclear fusion power generation

International Nuclear Information System (INIS)

2000-04-01

This book comprised of two issues. The first one is a advanced nuclear reactor which describes nuclear fuel cycle and advanced nuclear reactor like liquid-metal reactor, advanced converter, HTR and extra advanced nuclear reactors. The second one is nuclear fusion for generation energy, which explains practical conditions for nuclear fusion, principle of multiple magnetic field, current situation of research on nuclear fusion, conception for nuclear fusion reactor and economics on nuclear fusion reactor.

Development of Probabilistic Safety Assessment with respect to the first demonstration nuclear power plant of high temperature gas cooled reactor in China

International Nuclear Information System (INIS)

Tong Jiejuan; Zhao Jun; Liu Tao; Xue Dazhi

2012-01-01

Due to the unique concept of HTR-PM (High Temperature Gas Cooled Reactor-Pebble Bed Module) design, Chinese nuclear authority has anticipated that HTR-PM will bring challenge to the present regulation. The pilot use of PSA (Probabilistic Safety Assessment) during HTR-PM design and safety review is deemed to be the necessary and efficient tool to tackle the problem, and is actively encouraged as indicated in the authority's specific policy statement on HTR-PM project. The paper summarizes the policy statement to set up the base of PSA development and application activities. The up-to-date status of HTR-PM PSA development and the risk-informed application activities are introduced in this paper as the follow-up response to the policy statement. For open discussion, the paper hereafter puts forward several technical issues which have been encountered during HTR-PM PSA development. Since HTR-PM PSA development experience has the general conclusion that many of the PSA elements can be and have been implemented successfully by the traditional PSA techniques, only the issues which extra innovative efforts may be needed are highlighted in this paper. They are safety goal and risk metrics, PSA modeling framework for the non-water reactors, passive system reliability evaluation, initiating events frequencies and component reliability data estimation techniques for the new reactors and so on. The paper presents the way in which the encountered technical issues were or will be solved, although the proposed way may not be the ultimate best solution. The paper intends to express the standpoint that although the PSA of new reactor has the inherent weakness due to the insufficient information and larger data uncertainty, the problem of component reliability data is much less severe than people have conceived. The unique design conception and functional features of the reactors can influence the results more significantly than the component reliability data. What we are benefited

Financing models for HTR plants: Co-financing, counter trade, joint ventures

International Nuclear Information System (INIS)

Bogen, J.; Stoelzl, D.

1987-01-01

Structure and volume of investment cost for HTR nuclear power plants are different in comparison to other types of nuclear power plants. Even if the share of local participation is in comparable order of magnitude to other nuclear power plants, the required technical infrastructure for HTR plants is more suitable for existing and still practised technologies in countries which are in development processes. These HTR specific features offer special possibilities in HTR project financing. Various models are discussed in respect of the special HTR situation. Even if it is not possible to point out in a general manner the best solution - due to national, local and time dependant situations - this paper discusses the HTR specific impacts to buyer's credit financing, supplier's credit financing, barter trades or joint ventures and combined financing. (author). 4 refs, 9 figs

Development of digital I&C system in HTR-PM

International Nuclear Information System (INIS)

Shi Guilian

2014-01-01

Conclusions: HTR-PM DCS has been under execution for 5 years( 2009-2014) . It has taken CTEC 150 man/year so far. With close cooperation with INET, Chinergyand Shanghai Electric, CTEC overcame difficulties, like iterative design, voluminous customization work, new technology, and lacking of drawings. However, the accomplishment of the planned milestones prepared CTEC for the following work in HTR-PM DCS. 1. The 1ST integrated DCS, including safety DCS, non-safety DCS, DEH supplied by Chinese supplier. Rod control system and DEH are integrated in non-safety DCS. Simplified interface, integrated platform, and easy to use and maintenance. 2. CTEC obtained knowledge of 4th generation HTR-PM digital I&C, key design technology, and riched its DCS products by participation in HTRPM. HTR-PM Safety DCS project provided valuable experience for CTEC’s development and application of FIRMSYS, a safety protection control system platform. 3. The qualification solution by customized HTR-PM safety DCS prototype helps simply safety DCS design, V&V, qualification and safety review of the actual system, but results in some problems in system upgrade and maintenance. With the satisfactory application of FIRMSYS in 1000mw PWR and platform qualification , the future HTR-PM safety DCS could be provided based on a qualified safety DCS platform.

South African safety assessment framework for the pebble bed modular reactor - HTR2008-58192

International Nuclear Information System (INIS)

Joubert, J.; Kohtz, N.; Coe, I.

2008-01-01

It is planned to construct a first of a kind Pebble Bed Modular Reactor (PBMR) in South Africa. A need has been recognized to accompany the licensing process for the PBMR with independent safety assessments to ensure that the safety case submitted by the applicant complies with the licensing requirements of the NNR. At the HTR 2006 Conference, the framework and major challenges on safety assessment that the South African National Nuclear Regulator (NNR) faces in developing and applying appropriate strategies and tools were presented. This paper discusses the current status of the various NNR assessment activities and describes how this will be considered in the NNR Final Report on the PBMR Safety Case. The traditional safety assessment process has been adapted to take into account the developmental nature of the project. By performing safety assessments, the designer and applicant must ensure that the design as proposed for construction and as-built meets the safety requirements defined by the regulatory framework. The regulator performs independent safety assessments, including independent analyses in areas deemed safety significant and potentially safety significant. The developmental nature of the project also led to the identification of a series of regulatory assessment activities preceding the formal assessment of the safety case. Besides an assessment of the resolution of Key Licensing Issues which have been defined in an early stage of the project and are discussed in /l/, these activities comprise the participation in an SAR Early Intervention Process, the execution of a regulatory HAZOP and the development of a regulatory assessment specification for the formal assessment of the safety case. This paper briefly describes these activities and their current status. During the last two years, significant progress was made with the development or adjustment of tools for the independent analysis by the regulator of the steady state core design, of the transient

Design and Experiment of Auxiliary Bearing for Helium Blower of HTR-PM

International Nuclear Information System (INIS)

Yang Guojun; Shi Zhengang; Liu Xingnan; Zhao Jingjing

2014-01-01

The helium blower is the important equipment for HTR-PM. Active magnetic bearing (AMB) instead of mechanical bearing is selected to support the rotor of the helium blower. However, one implication of AMB is the requirement to provide the auxiliary bearing to mitigate the effects of failures or overload conditions. The auxiliary bearing is used to support the rotor when the AMB fails to work. It must support the dropping rotor and bear the great impact force and friction heat. The design of the auxiliary bearing is one of the challenging problems in the whole system. It is very important for the helium blower with AMB of HTR-PM to make success. The rotor’s length of helium blower of HTR-PM is about 3.3 m, its weight is about 4000 kg and the rotating speed is 4000 r/min. The axial load is 4500kg, and the radial load is 1950kg. The angular contact ball bearing was selected as the auxiliary bearing. The test rig has been finished. It is difficult to analyze the falling course of the rotor. The preliminary analysis of the dropping rotor was done in the special condition. The impact force of auxiliary bearing was computed for the axial and radial load. And the dropping test of the blower rotor for HTR-10 will be introduced also in this paper. Results offer the important theoretical base for the protector design of the helium blower with AMB for HTR-PM. (author)

Tardive dyskinesia and DRD3, HTR2A and HTR2C gene polymorphisms in Russian psychiatric inpatients from Siberia

NARCIS (Netherlands)

Al Hadithy, A. F. Y.; Ivanova, S. A.; Pechlivanoglou, P.; Semke, A.; Fedorenko, O.; Kornetova, E.; Ryadovaya, L.; Brouwers, J. R. B. J.; Wilffert, B.; Bruggeman, R.; Loonen, A. J. M.

2009-01-01

Background: Pharmacogenetics of tardive dyskinesia and dopamine D3 (DRD3), serotonin 2A (HTR2A), and 2C (HTR2C) receptors has been examined in various populations, but not in Russians. Purpose: To investigate the association between orofaciolingual (TDof) and limb-truncal dyskinesias (TDlt) and

Coordinated Control Design for the HTR-PM Plant: From Theoretic Analysis to Simulation Verification

International Nuclear Information System (INIS)

Dong Zhe; Huang Xiaojin

2014-01-01

HTR-PM plant is a two-modular nuclear power plant based on pebble bed modular high temperature gas-cooled reactor (MHTGR), and adopts operation scheme of two nuclear steam supplying systems (NSSSs) driving one turbine. Here, an NSSS is composed of an MHTGR, a once-through steam generator (OTSG) and some connecting pipes. Due to the coupling effect induced by two NSSSs driving one common turbine and that between the MHTGR and OTSG given by common helium flow, it is necessary to design a coordinated control for the safe, stable and efficient operation of the HTR-PM plant. In this paper, the design of the feedback loops and control algorithms of the coordinated plant control law is firstly given. Then, the hardware-in-loop (HIL) system for verifying the feasibility and performance of this control strategy is introduced. Finally, some HIL simulation results are given, which preliminarily show that this coordinated control law can be implemented practically. (author)

GTHTR 300 economic calculation with Mini G4ECONS as a basis for generation cost of GTHTR 10 MWe calculation

International Nuclear Information System (INIS)

Mochamad Nasrullah; Nurlaila

2014-01-01

The government plan to build Experimental Power Reactor (EPR) requires measurable economic assessment. The purpose of the study was to recalculate Gas Turbine High Temperature Reactor of 300 MWe (GTHTR 300) and compare the results with reference data. Then calculate generation cost of GTHTR 3, 5 and 10 MWe using the scale factor calculation. The methodology used is covered the generation cost calculation using the Mini G4Econs spread sheet models published by IAEA. Result of the verification calculation showed that a relatively similar, which means that the calculation model could be used to calculate for same other cases. Afterward, using scale factor, smaller scale reactor could be calculated. The calculation result show that electricity generation cost of SMR-HTR type with load factor 90% and discount rate 10% for power capacity 3, 5 and 10 MWe are 29.5, 22.68 and 16.17 cents$/kWh respectively. However, because the EPR is planning to be built as a non-commercial power reactors, then 5 % and 3 % of discount rate could be chosen, each of those discount rate will result electricity generation cost of 10.37 cents$/kWh and 8.56 cents$/kWh respectively. These result could be considered by the government for developing SMR type of HTR. (author)

Assessments of Water Ingress Accidents in a Modular High-Temperature Gas-Cooled Reactor

International Nuclear Information System (INIS)

Zhang Zuoyi; Dong Yujie; Scherer, Winfried

2005-01-01

Severe water ingress accidents in the 200-MW HTR-module were assessed to determine the safety margins of modular pebble-bed high-temperature gas-cooled reactors (HTR-module). The 200-MW HTR-module was designed by Siemens under the criteria that no active safety protection systems were necessary because of its inherent safe nature. For simulating the behavior of the HTR-module during severe water ingress accidents, a water, steam, and helium multiphase cavity model was developed and implemented in the dynamic simulator for nuclear power plants (DSNP) simulation system. Comparisons of the DSNP simulations incorporating these models with experiments and with calculations using the time-dependent neutronics and temperature dynamics code were made to validate the simulation. The analysis of the primary circuit showed that the maximum water concentration increase in the reactor core was 3 s). The water vaporization in the steam generator and characteristics of water transport from the steam generator to the reactor core would reduce the rate of water ingress into the reactor core. The analysis of a full cavitation of the feedwater pump showed that if the secondary circuit could be depressurized, the feedwater pump would be stopped by the full cavitation. This limits the water transported from the deaerator to the steam generator. A comprehensive simulation of the HTR-module power plant showed that the water inventory in the primary circuit was limited to ∼3000 kg. The nuclear reactivity increase caused by the water ingress would lead to a fast power excursion, which would be inherently counterbalanced by negative feedback effects. The integrity of the fuel elements, because the safety-relevant temperature limit of 1600 deg. C is not reached in any case, is not challenged

The challenge of introducing high-temperature reactor plants onto the international power plant market

International Nuclear Information System (INIS)

Bogen, J.; Stoelzl, D.

1987-01-01

Growth of world population increases energy demand until the year 2000 and afterwards. Electricity growth rates in industrialized nations are lower after the oil price escalation in 1973 and 1979, and in developing countries grid sizes are often too small for the operation of large LWR plants. This indicates a potential for small and medium-sized power reactors such as the HTR-100 and the HTR-500. These plants can compete with coal fired plants of comparable size. An HTR-500 is even competitive, considering the electricity generating cost of large LWR plants. The special advantages of HTR plants in the small and medium-capacity range are discussed. (orig.)

The challenge of introducing high-temperature-reactor plants onto the international power plant market

International Nuclear Information System (INIS)

Bogen, J.; Stoelzl, D.

1988-01-01

Growth of world population increases energy demand until the year 2000 and afterwards. Electricity growth rates in industrialized nations are lower after the oil price escalation in 1973 and 1979, and in developing countries grid sizes are often too small for the operation of large LWR plants. This indicates a potential for small and medium-sized power reactors such as the HTR-100 and the HTR-500. These plants can compete with coal fired plants of comparable size. An HTR-500 is even competitive, considering the electricity generating cost of large LWR plants. The special advantages of HTR plants in the small and medium-capacity range are discussed. (orig.)

Simulation of the fuzzy-smith control system for the high temperature gas cooled reactor

International Nuclear Information System (INIS)

Li Deheng; Xu Xiaolin; Zheng Jie; Guo Renjun; Zhang Guifen

1997-01-01

The Fuzzy-Smith pre-estimate controller to solve the control of the big delay system is developed, accompanied with the development of the mathematical model of the 10 MW high temperature gas cooled test reactor (HTR-10) and the design of its control system. The simulation results show the Fuzzy-Smith pre-estimate controller has the advantages of both fuzzy control and Smith pre-estimate controller; it has better compensation to the delay and better adaptability to the parameter change of the control object. So it is applicable to the design of the control system for the high temperature gas cooled reactor

Notes on HTR applications in methanol production

International Nuclear Information System (INIS)

Santoso, B.; Barnert, H.

1997-01-01

Notes on the study of HTR applications are presented. The study in particular should be directed toward the most feasible applications of HTR for process heat generation. A prospective study is the conversion of CO 2 gas from Natuna to methanol or formic acid. Further studies needs to be deepened under the auspices of IAEA and countries that have similar interest. (author). 3 refs, 3 figs

Review of PSI studies on reactor physics and thermal fluid dynamics of pebble bed reactors

International Nuclear Information System (INIS)

Prasser, Horst-Michael

2014-01-01

Switzerland is member of the Generation IV International Forum (GIF). The related work takes entirely place at PSI in the working groups of Gas-Cooled Fast Reactors and Very High Temperature Reactors. In the past, PSI has performed experimental and theoretical studies on criticality issues of pebble beds at the PROTEUS reactor, as well as a preliminary risk assessment of a prototypal HTR as an input for a comparison of energy supply options. PROTEUS was a critical assembly with an annular driver zone. The central region was filled by arrangements of fuel spheres. The reactivity effect of a water ingress was investigated by simulating the water by polyethylene rods of different diameter inserted into the gaps of a regular package. For sub-criticality measurements in pebble beds, a built-in pulsed neutron source was used. The experimental results were used to validate diffusion and higher order neutron transport models. Concerning thermal hydraulics of gas flows, the vast experience of PSI is focused on hydrogen transport, accumulation, and dispersion in containments of light water reactors. The phenomena are comparable in many aspects to the fluid dynamic issues relevant to HTR. Experiments on hydrogen flows are performed for numerous scenarios in the large-scale containment test facility PANDA. Hydrogen is substituted by helium as a model fluid. An important generic aspect is turbulent mixing in the presence of strong stratification, which is relevant for HTR as well. In a parallel project, generic small-scale mixing experiments with a high density ratio of 1:7 are carried out in a horizontal rectangular channel, where helium and nitrogen flows are brought into contact downstream of the rear edge of a splitter plate. Due to the high density ratio, turbulent mixing is affected by strong non-Boussinesq effects. The measurements taken by Particle Imaging Velocimetry (PIV) and Laser Induced Fluorescence techniques are compared to RANS and LES simulations. Similar large

IRPhE-DRAGON-DPR, OECD High Temperature Reactor Dragon Project, Primary Documents

International Nuclear Information System (INIS)

2004-01-01

Description: The DRAGON Reactor Experiment (DRE): The first demonstration High temperature gas reactor (HTGR) was built in the 1960's. Thirteen OECD countries began a project in 1959 to build an experimental reactor known as Dragon at Winfrith in the UK. The reactor - which operated successfully between 1966 and 1975 - had a thermal output of 20 MW and achieved a gas outlet temperature of 750 deg. C. The High Temperature Reactor concept, if it justified its expectations, was seen as having its place as an advanced thermal reactor between the current thermal reactor types such as the PWR, BWR, and AGR and the sodium cooled fast breeder reactor. It was expected that the HTR would offer better thermal efficiency, better uranium utilisation, either with low enriched uranium fuel or high enriched uranium thorium fuel, better inherent safety and lower unit power costs. In the event all these potential advantages were demonstrated to be in principle achievable. This view is still shared today. In fact Very High Temperature Reactors is one of the concepts retained for Generation IV. Projects on constructing Modular Pebble Bed Reactors are under way. Here all available Dragon Project Reports (DPR) - approximately 1000 - are collected in electronic form. An index points to the reports (PDF format); each table in the report is accessible in EXCEL format with the aim of facilitating access to the data. These reports describe the design, experiments and modelling carried out over a period of 17 years. 2 - Related or auxiliary information: IRPHE-HTR-ARCH-01, Archive of HTR Primary Documents NEA-1728/01. 3 - Software requirements: Acrobat Reader, Microsoft Word, HTML Browser required

Analysis of impact of mixing flow on the pebble bed high temperature reactor

International Nuclear Information System (INIS)

Hao Chen; Li Fu; Guo Jiong

2014-01-01

The impact of the mixing flow in the pebble flow on pebble bed high temperature gas cooled reactor (HTR) was analyzed in the paper. New code package MFVSOP which can simulate the mixing flow was developed. The equilibrium core of HTR-PM was selected as reference case, the impact of the mixing flow on the core parameters such as core power peak factor, power distribution was analyzed with different degree of mixing flow, and uncertainty analysis was carried out. Numerical results showed that the mixing flow had little impact on key parameters of pebble bed HTR, and the multiple-pass-operation-mode in pebble bed HTR can reduce the uncertainty arouse from the mixing flow. (authors)

Impact of the Improved Resonance Scattering Kernel on HTR Calculations

International Nuclear Information System (INIS)

Becker, B.; Dagan, R.; Broeders, C.H.M.; Lohnert, G.

2008-01-01

The importance of an advanced neutron scattering model for heavy isotopes with strong energy dependent cross sections such as the pronounced resonances of U 238 has been discussed in various publications where the full double differential scattering kernel was derived. In this study we quantify the effect of the new scattering model for specific innovative types of High Temperature Reactor (HTR) systems which commonly exhibit a higher degree of heterogeneity and higher fuel temperatures, hence increasing the importance of the secondary neutron energy distribution. In particular the impact on the multiplication factor (k ∞ ) and the Doppler reactivity coefficient is presented in view of the packing factors and operating temperatures. A considerable reduction of k ∞ (up to 600 pcm) and an increased Doppler reactivity (up to 10%) is observed. An increase of up to 2.3% of the Pu 239 inventory can be noticed at 90 MWd/tHM burnup due to enhanced neutron absorption of U 238 . Those effects are more pronounced for design cases in which the neutron flux spectrum is hardened towards the resolved resonance range. (authors)

Studies for the layout and technical conception of a two-circuit HTR power plant of 600 MWsub(el) under public utilizer aspects

International Nuclear Information System (INIS)

Schuetten, R.

1981-01-01

In this study concerning conceptions for a nuclear power plant of 600 MWsub(el) with high-temperature reactor a conception for a HTR-nuclear power plant of 600 MWsub(el) to be built in the Federal Republic of Germany in future is developed on the basis of operating experience with the 15-MW-AVR-experimental nuclear power plant, the construction of the THTR-300 nuclear power plant and the gas-cooled reactors of English, French and American origin. This report gives a survey of the most important findings and the requirements on behalf of the public utilities for a nuclear power plant with high-temperature reactor with the dimensions of 600 MWsub(el). The examination of the utilities basic requirements for a power plant and the experience made during the licensing procedure led to this technical and safety conception for a HTR nuclear power plant with spherical fuel elements. In addition, the questions of the possibility of recurrent tests and of repairing safety components and also the future shut-down of the power plant, which are important for the public utilities, are examined. (orig./GL) [de

Gas reactor international cooperative program interim report: German Pebble Bed Reactor design and technology review

International Nuclear Information System (INIS)

1978-09-01

This report describes and evaluates several gas-cooled reactor plant concepts under development within the Federal Republic of Germany (FRG). The concepts, based upon the use of a proven Pebble Bed Reactor (PBR) fuel element design, include nuclear heat generation for chemical processes and electrical power generation. Processes under consideration for the nuclear process heat plant (PNP) include hydrogasification of coal, steam gasification of coal, combined process, and long-distance chemical heat transportation. The electric plant emphasized in the report is the steam turbine cycle (HTR-K), although the gas turbine cycle (HHT) is also discussed. The study is a detailed description and evaluation of the nuclear portion of the various plants. The general conclusions are that the PBR technology is sound and that the HTR-K and PNP plant concepts appear to be achievable through appropriate continuing development programs, most of which are either under way or planned

Comparative Study on Electric Generation Cost of HTR with Another Electric Plant Using LEGECOST Program

International Nuclear Information System (INIS)

Mochamad-Nasrullah; Soetrisnanto, Arnold Y.; Tosi-Prastiadi; Adiwardojo

2000-01-01

Monetary and economic crisis in Indonesia resulted in impact of electricity and demand and supply planning that it has to be reevaluated. One of the reasons is budget limitation of the government as well as private companies. Considering this reason, the economic calculation for all of aspect could be performed, especially the calculation of electric generation cost. This paper will discuss the economic aspect of several power plants using fossil and nuclear fuel including High Temperature Reactor (HTR). Using Levelized Generation Cost (LEGECOST) program developed by IAEA (International Atomic Energy Agency), the electric generation cost of each power plant could be calculated. And then, the sensitivity analysis has to be done using several economic parameters and scenarios, in order to be known the factors that influence the electric generation cost. It could be concluded, that the electric generation cost of HTR is cheapest comparing the other power plants including nuclear conventional. (author)

Plutonium burning in a pebble-bed type high temperature nuclear reactor

Energy Technology Data Exchange (ETDEWEB)

Bende, E.E

2000-01-24

This thesis deals with the pebble-bed High Temperature Reactor that is fuelled with pure reactor-grade plutonium. It is stressed that neither burnable poisons nor fertile materials like 238U and 212Th are present in the calculational models throughout this thesis. Chapter 2 discusses the general properties of the pebble-bed HTR: the passive safety features of this reactor; different fuel scenarios according to which the pebble-bed HTR can be operated; properties of the pebbles and the coated particles (CPs), including a concise overview of the mechanisms that can lead to coated particle failure. Special attention is paid to the effect of Pu as fuel inside these CPs thereby aiming to indicate which mechanisms are of concern when such CPs are considered as fuel in future reactors. In the last part of this chapter constraints are listed that were imposed to the models considered in the framework of this thesis. Chapter 3 presents the results of unit-cell calculations performed with three code systems. The main objective of this chapter is to compare the calculational results of one particular code system, which is a candidate for the generation of cross sections for a full-core calculation, to those of the other two code systems. Also some reactor physics interpretations of the calculational results are presented. The unit-cell calculations embrace the computation of a number of reactor physics parameters for pebbles with a varying plutonium mass per pebble and with different types of coated particles. For one pebble configuration, these parameters have been calculated for various fuel temperatures and over-all (uniform) temperatures. For that particular pebble configuration, also the results of a two burnup calculations were compared. Chapter 4 reports the results of a parameter study in which the number of coated particles per pebble as well as the type and size of the CPs have been varied. The effect of different pebble configurations on several reactor physics

Axial temperatures and fuel management models for a HTR system

Energy Technology Data Exchange (ETDEWEB)

Hansen, U

1971-11-12

In the HTR system, there is a large difference in temperature between different parts of the reactor core. The softer neutron spectrum in the upper colder core regions tends to shift the power productions in the fresh fuel upwards. As uranium 235 depletes and plutonium with its higher cross sections in the lower hot regions is built-up, an axial power flattening takes place. These effects have been studied in detail for a single column in an equilibrium environment. The aim of this paper is to relate these findings to a whole reactor core and to investigate the influence of axial temperatures on the overall performance and in particular, the fuel management scheme chosen for the reference design. A further objective has been to calculate the reactivity requirements for different part load conditions and for various daily and weekly load diagrams. As the xenon cross section changes significantly with temperature these investigations are performed for an equilibrium core with due representation of axial temperature zones.

Vagal innervation is required for pulmonary function phenotype in Htr4-/- mice.

Science.gov (United States)

House, John S; Nichols, Cody E; Li, Huiling; Brandenberger, Christina; Virgincar, Rohan S; DeGraff, Laura M; Driehuys, Bastiaan; Zeldin, Darryl C; London, Stephanie J

2017-04-01

Human genome-wide association studies have identified over 50 loci associated with pulmonary function and related phenotypes, yet follow-up studies to determine causal genes or variants are rare. Single nucleotide polymorphisms in serotonin receptor 4 ( HTR4 ) are associated with human pulmonary function in genome-wide association studies and follow-up animal work has demonstrated that Htr4 is causally associated with pulmonary function in mice, although the precise mechanisms were not identified. We sought to elucidate the role of neural innervation and pulmonary architecture in the lung phenotype of Htr4 -/- animals. We report here that the Htr4 -/- phenotype in mouse is dependent on vagal innervation to the lung. Both ex vivo tracheal ring reactivity and in vivo flexiVent pulmonary functional analyses demonstrate that vagotomy abrogates the Htr4 -/- airway hyperresponsiveness phenotype. Hyperpolarized 3 He gas magnetic resonance imaging and stereological assessment of wild-type and Htr4 -/- mice reveal no observable differences in lung volume, inflation characteristics, or pulmonary microarchitecture. Finally, control of breathing experiments reveal substantive differences in baseline breathing characteristics between mice with/without functional HTR4 in breathing frequency, relaxation time, flow rate, minute volume, time of inspiration and expiration and breathing pauses. These results suggest that HTR4's role in pulmonary function likely relates to neural innervation and control of breathing. Copyright © 2017 the American Physiological Society.

HTR 500: Final report of the project '' uniaxial creep tests at controlled temperature''

International Nuclear Information System (INIS)

1992-03-01

The report presents the results of creep trials with HTR-concrete, which were carried out in the scope of development of prestressed concrete - reactor pressure vessels at the ETH Lausanne Institute for Steel and Prestressed Concrete. With temperature, an increase of creep and shrinkage was observed, a lesser dependence on exhaustion and type of concrete. The point in time of reaching the final value is not dependent on temperature for creep, but is for shrinkage. The modulus of elasticity depends on the temperature pre-treatment, but only insignificantly on the test temperature. figs., tabs

The analysis for inventory of experimental reactor high temperature gas reactor type

International Nuclear Information System (INIS)

Sri Kuntjoro; Pande Made Udiyani

2016-01-01

Relating to the plan of the National Nuclear Energy Agency (BATAN) to operate an experimental reactor of High Temperature Gas Reactors type (RGTT), it is necessary to reactor safety analysis, especially with regard to environmental issues. Analysis of the distribution of radionuclides from the reactor into the environment in normal or abnormal operating conditions starting with the estimated reactor inventory based on the type, power, and operation of the reactor. The purpose of research is to analyze inventory terrace for Experimental Power Reactor design (RDE) high temperature gas reactor type power 10 MWt, 20 MWt and 30 MWt. Analyses were performed using ORIGEN2 computer code with high temperatures cross-section library. Calculation begins with making modifications to some parameter of cross-section library based on the core average temperature of 570 °C and continued with calculations of reactor inventory due to RDE 10 MWt reactor power. The main parameters of the reactor 10 MWt RDE used in the calculation of the main parameters of the reactor similar to the HTR-10 reactor. After the reactor inventory 10 MWt RDE obtained, a comparison with the results of previous researchers. Based upon the suitability of the results, it make the design for the reactor RDE 20MWEt and 30 MWt to obtain the main parameters of the reactor in the form of the amount of fuel in the pebble bed reactor core, height and diameter of the terrace. Based on the main parameter or reactor obtained perform of calculation to get reactor inventory for RDE 20 MWT and 30 MWT with the same methods as the method of the RDE 10 MWt calculation. The results obtained are the largest inventory of reactor RDE 10 MWt, 20 MWt and 30 MWt sequentially are to Kr group are about 1,00E+15 Bq, 1,20E+16 Bq, 1,70E+16 Bq, for group I are 6,50E+16 Bq, 1,20E+17 Bq, 1,60E+17 Bq and for groups Cs are 2,20E+16 Bq, 2,40E+16 Bq, 2,60E+16 Bq. Reactor inventory will then be used to calculate the reactor source term and it

Postirradiation examination of HTR fuel

International Nuclear Information System (INIS)

Nabielek, H.; Reitsamer, G.; Kania, M.J.

1986-01-01

Fuel for the High Temperature Reactor (HTR) consists of 1 mm diameter coated particles uniformly distributed in a graphite matrix within a cold-molded 60 mm diameter spherical fuel element. Fuel performance demonstrations under simulated normal operation conditions are conducted in accelerated neutron environments available in Material Test Reactors and in real-time environments such as the Arbeitsgemeinschaft Versuchsreaktor (AVR) Juelich. Postirradiation examinations are then used to assess fuel element behavior and the detailed performance of the coated particles. The emphasis in postirradiation examination and accident testing is on assessment of the capability for fuel elements and individual coated particles to retain fission products and actinide fuel materials. To accomplish this task, techniques have been developed which measures fission product and fuel material distributions within or exterior to the particle: Hot Gas Chlorination - provides an accurate method to measure total fuel material concentration outside intact particles; Profile Electrolytic Deconsolidation - permits determination of fission product distribution along fuel element diameter and retrieval of fuel particles from positions within element; Gamma Spectrometry - provides nondestructive method to measure defect particle fractions based on retention of volatile metallic fission products; Particle Cracking - permits a measure of the partitioning of fission products between fuel kernel and particle coatings, and the derivation of diffusion parameters in fuel materials; Micro Gas Analysis - provides gaseous fission product and reactive gas inventory within free volume of single particles; and Mass-spectrometric Burnup Determination - utilizes isotope dilution for the measurement of heavy metal isotope abundances

Tritium in HTR systems

International Nuclear Information System (INIS)

Steinwarz, W.

1987-07-01

Starting from the basis of the radiological properties of tritium, the provisions of present-day radiation protection legislation are discussed in the context of the handling of this radionuclide in HTR plants. Tritium transportation is then followed through from the place of its creation up until the sink, i.e. disposal and/or environmental route, and empirical values obtained in experiments and in plant operation translated into guidelines for plant design and planning. The use of the example of modular HTR plants permits indication that environmental contamination via the 'classical' routes of air and water emissions, and contamination of products, and resulting consumer exposure, are extremely low even on the assumption of extreme conditions. This leads finally to a requirement that the expenditure for implementation of measures for further reduction of tritium activity rates be measured against low radiological effect. (orig.) [de

Severe water ingress accident analysis for a Modular High Temperature Gas Cooled Reactor

International Nuclear Information System (INIS)

Zhang Zuoyi; Scherer, Winfried

1997-01-01

This paper analyzes the severe water ingress accidents in the SIEMENS 200MW Modular High Temperature Gas Cooled Reactor (HTR-Module) under the assumption of no active safety protection systems in order to find the safety margin of the current HTR-Module design. A water, steam and helium multi-phase cavity model is originally developed and implemented in the DSNP simulation system. The developed DSNP system is used to simulate the primary circuit of HTR-Module power plant. The comparisons of the models with the TINTE calculations validate the current simulation. After analyzing the effects of blower separation on water droplets, the wall heat storage, etc., it is found that the maximum H 2 O density increase rate in the reactor core is smaller than 0.3 kg/(m 3 s). The liquid water vaporization in the steam generator and H 2 O transport from the steam generator to the reactor core reduces the impulse of the H 2 O in the reactor core. The nuclear reactivity increase caused by the water ingress leads to a fast power excursion, which, however, is inherently counterbalanced by negative feedback effects. Concerning the integrity of the fuel elements, the safety relevant temperature limit of 1600degC was not reached in any case. (author)

Generation IV reactors: international projects

International Nuclear Information System (INIS)

Carre, F.; Fiorini, G.L.; Kupitz, J.; Depisch, F.; Hittner, D.

2003-01-01

Generation IV international forum (GIF) was initiated in 2000 by DOE (American department of energy) in order to promote nuclear energy in a long term view (2030). GIF has selected 6 concepts of reactors: 1) VHTR (very high temperature reactor system, 2) GHR (gas-cooled fast reactor system), 3) SFR (sodium-cooled fast reactor system, 4) SCWR (super-critical water-cooled reactor system), 5) LFR (lead-cooled fast reactor system), and 6) MFR (molten-salt reactor system). All these 6 reactor systems have been selected on criteria based on: - a better contribution to sustainable development (through their aptitude to produce hydrogen or other clean fuels, or to have a high energy conversion ratio...) - economic profitability, - safety and reliability, and - proliferation resistance. The 6 concepts of reactors are examined in the first article, the second article presents an overview of the results of the international project on innovative nuclear reactors and fuel cycles (INPRO) within IAEA. The project finished its first phase, called phase-IA. It has produced an outlook into the future role of nuclear energy and defined the need for innovation. The third article is dedicated to 2 international cooperations: MICANET and HTR-TN. The purpose of MICANET is to propose to the European Commission a research and development strategy in order to develop the assets of nuclear energy for the future. Future reactors are expected to be more multiple-purposes, more adaptable, safer than today, all these developments require funded and coordinated research programs. The aim of HTR-TN cooperation is to promote high temperature reactor systems, to develop them in a long term perspective and to define their limits in terms of burn-up and operating temperature. (A.C.)

Critical evaluation of the experiments and mathematical models for the determination of fission product release from the spherical fuel elements in cases of core heating accidents in modular HTR's

International Nuclear Information System (INIS)

Bailly, H.W.

1987-01-01

In this work, the thermal behaviour of modular reactors in cases of core heating accidents and the physical phenomena relevant for a release of radioactive materials from HTR fuel elements are explained as far as is necessary for understanding the work. The present mathematical models by which the release of radioactive materials from HTR fuel elements due to diffusion or breaking particles in cases of core heating accidents are also described, examined and evaluated with regard to their applicability to module reactors. The experiments used to verify the mathematical models are also evaluated. The mathematical models are in nearly all cases computer programs, which describe the complicated process of releasing radioactive materials quantitative mathematically. One should point out that these models are constantly being developed further, in line with the increasing amount of knowledge. To conclude the work, proposals are made for improving the certainty of information from experiments and mathematical models to determine the release behaviour of modular reactors. (orig./GL) [de

Process heat cogeneration using a high temperature reactor

International Nuclear Information System (INIS)

Alonso, Gustavo; Ramirez, Ramon; Valle, Edmundo del; Castillo, Rogelio

2014-01-01

Highlights: • HTR feasibility for process heat cogeneration is assessed. • A cogeneration coupling for HTR is proposed and process heat cost is evaluated. • A CCGT process heat cogeneration set up is also assessed. • Technical comparison between both sources of cogeneration is performed. • Economical competitiveness of the HTR for process heat cogeneration is analyzed. - Abstract: High temperature nuclear reactors offer the possibility to generate process heat that could be used in the oil industry, particularly in refineries for gasoline production. These technologies are still under development and none of them has shown how this can be possible and what will be the penalty in electricity generation to have this additional product and if the cost of this subproduct will be competitive with other alternatives. The current study assesses the likeliness of generating process heat from Pebble Bed Modular Reactor to be used for a refinery showing different plant balances and alternatives to produce and use that process heat. An actual practical example is presented to demonstrate the cogeneration viability using the fact that the PBMR is a modular small reactor where the cycle configuration to transport the heat of the reactor to the process plant plays an important role in the cycle efficiency and in the plant economics. The results of this study show that the PBMR would be most competitive when capital discount rates are low (5%), carbon prices are high (>30 US$/ton), and competing natural gas prices are at least 8 US$/mmBTU

Process heat cogeneration using a high temperature reactor

Energy Technology Data Exchange (ETDEWEB)

Alonso, Gustavo, E-mail: gustavoalonso3@gmail.com [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca s/n, Ocoyoacac, Edo. De Mexico 52750 (Mexico); Instituto Politécnico Nacional, Unidad Profesional Adolfo Lopez Mateos, Ed. 9, Lindavista, D.F. 07300 (Mexico); Ramirez, Ramon [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca s/n, Ocoyoacac, Edo. De Mexico 52750 (Mexico); Valle, Edmundo del [Instituto Politécnico Nacional, Unidad Profesional Adolfo Lopez Mateos, Ed. 9, Lindavista, D.F. 07300 (Mexico); Castillo, Rogelio [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca s/n, Ocoyoacac, Edo. De Mexico 52750 (Mexico)

2014-12-15

Highlights: • HTR feasibility for process heat cogeneration is assessed. • A cogeneration coupling for HTR is proposed and process heat cost is evaluated. • A CCGT process heat cogeneration set up is also assessed. • Technical comparison between both sources of cogeneration is performed. • Economical competitiveness of the HTR for process heat cogeneration is analyzed. - Abstract: High temperature nuclear reactors offer the possibility to generate process heat that could be used in the oil industry, particularly in refineries for gasoline production. These technologies are still under development and none of them has shown how this can be possible and what will be the penalty in electricity generation to have this additional product and if the cost of this subproduct will be competitive with other alternatives. The current study assesses the likeliness of generating process heat from Pebble Bed Modular Reactor to be used for a refinery showing different plant balances and alternatives to produce and use that process heat. An actual practical example is presented to demonstrate the cogeneration viability using the fact that the PBMR is a modular small reactor where the cycle configuration to transport the heat of the reactor to the process plant plays an important role in the cycle efficiency and in the plant economics. The results of this study show that the PBMR would be most competitive when capital discount rates are low (5%), carbon prices are high (>30 US$/ton), and competing natural gas prices are at least 8 US$/mmBTU.

Post-irradiation examination of HTR-fuel at the Austrian Research Centre Seibersdorf Ltd

International Nuclear Information System (INIS)

Reitsamer, G.; Proksch, E.; Stolba, G.; Strigl, A.; Falta, G.; Zeger, J.

1985-01-01

Austrian R and D activities in the HTR-field reach back almost to the beginning of this advanced reactor line. For more than 20 years post-irradiation examination (PIE) of HTR-fuel has been performed at the laboratories of the Austrian Research Centre Seibersdorf Ltd. (OEFZS) (formerly OESGAE) and a high degree of qualification has been achieved in the course of that time. Most of the PIE-work has been carried out by international cooperation on contract basis with the OECD-DRAGON-project and with KFA-Juelich (FRG). There has also been some collaboration with GA (USA), Belgonucleaire and others in the past. HTR-fuel elements contain the fissile and fertile materials in form of coated particles (CPs) which are embedded in a graphite matrix. Because of this special design it has been necessary from the very beginning of the PIE work up to now to develop new methods (i.e. fuel element disintegration methods, chlorine gas leach, single particle examination techniques...) as well as to adapt and improve already existing methods (i.e. gamma spectrometry, mass-spectrometry, optical methods...). The main interests on PIE-work at Seibersdorf are concentrated on particle performance, fission product distribution and the 'free' Uranium content (contamination and broken particles) of the fuel elements (fuel spheres or cylindrical compacts). A short compilation of the applied methods and of available instrumental facilities is given as follows: deconsolidation of fuel elements; equipment for electrochemical deconsolidation; examinations and measurements of graphite and electrolyte samples; examination of coated particles; single particle examinations

Post-irradiation examination of HTR-fuel at the Austrian Research Centre Seibersdorf Ltd

Energy Technology Data Exchange (ETDEWEB)

Reitsamer, G; Proksch, E; Stolba, G; Strigl, A; Falta, G; Zeger, J [Department of Chemistry, Austrian Research Centre Seibersdorf Ltd., Seibersdorf (Austria)

1985-07-01

Austrian R and D activities in the HTR-field reach back almost to the beginning of this advanced reactor line. For more than 20 years post-irradiation examination (PIE) of HTR-fuel has been performed at the laboratories of the Austrian Research Centre Seibersdorf Ltd. (OEFZS) (formerly OESGAE) and a high degree of qualification has been achieved in the course of that time. Most of the PIE-work has been carried out by international cooperation on contract basis with the OECD-DRAGON-project and with KFA-Juelich (FRG). There has also been some collaboration with GA (USA), Belgonucleaire and others in the past. HTR-fuel elements contain the fissile and fertile materials in form of coated particles (CPs) which are embedded in a graphite matrix. Because of this special design it has been necessary from the very beginning of the PIE work up to now to develop new methods (i.e., fuel element disintegration methods, chlorine gas leach, single particle examination techniques...) as well as to adapt and improve already existing methods (i.e. gamma spectrometry, mass-spectrometry, optical methods...). The main interests on PIE-work at Seibersdorf are concentrated on particle performance, fission product distribution and the 'free' Uranium content (contamination and broken particles) of the fuel elements (fuel spheres or cylindrical compacts). A short compilation of the applied methods and of available instrumental facilities is given as follows: deconsolidation of fuel elements; equipment for electrochemical deconsolidation; examinations and measurements of graphite and electrolyte samples; examination of coated particles; single particle examinations.

Important viewpoints proposed for a safety approach of HTGR reactors in Europe

International Nuclear Information System (INIS)

Brinkmann, G.; Pirson, J.; Ehster, S.; Dominguez, M.T.; Mansani, L.; Coe, I.; Moormann, R.; Van der Mheen, W.

2006-01-01

The inherent safety features of modular High Temperature Reactors (HTRs) make events leading to severe core damage highly unlikely and constitute the main differentiating aspects compared to LWRs. Furthermore, while a known and stable regulatory environment has long been established for Light Water Reactors (LWRs), different ways of thinking may help to develop a more appropriate licensing process for HTR-based power plants. The HTR-L project funded by the European Commission in the 5th Framework Programme was dedicated to the definition of a common and coherent European safety approach and the identification of the main licensing issues for the licensing framework of the modular HTRs. Several topics were developed during the course of this project. Due to the characteristics of the HTR design, it has been necessary to define specific defence-in-depth requirements which have then been evaluated for implementation in the safety approach. Safety-related functions appropriate for the HTR design have also had to be identified and listed. On one hand, the different possible solicitations of the fuel particles constituted the starting point for the identification of the accidental conditions (by means of the Master Logic Diagrams methodology); these accidental conditions were classified and the most appropriate methods to consider ultra low probability severe accidents were examined. On the other hand, the elements constituting the source term and, in particular, the requirements for the confinement of radioactive products and the conditions required to prevent the need for a 'conventional' containment structure have been discussed. In the definition of the safety approach, attention has been paid to the need to maintain the potentially interesting economic perspectives of HTR reactors. Key issues to be addressed in the licensing process of the HTRs have also been identified. An innovative systems, structures and components classification method has been developed and

The nucleus accumbens 5-HTR4-CART pathway ties anorexia to hyperactivity

Science.gov (United States)

Jean, A; Laurent, L; Bockaert, J; Charnay, Y; Dusticier, N; Nieoullon, A; Barrot, M; Neve, R; Compan, V

2012-01-01

In mental diseases, the brain does not systematically adjust motor activity to feeding. Probably, the most outlined example is the association between hyperactivity and anorexia in Anorexia nervosa. The neural underpinnings of this ‘paradox', however, are poorly elucidated. Although anorexia and hyperactivity prevail over self-preservation, both symptoms rarely exist independently, suggesting commonalities in neural pathways, most likely in the reward system. We previously discovered an addictive molecular facet of anorexia, involving production, in the nucleus accumbens (NAc), of the same transcripts stimulated in response to cocaine and amphetamine (CART) upon stimulation of the 5-HT4 receptors (5-HTR4) or MDMA (ecstasy). Here, we tested whether this pathway predisposes not only to anorexia but also to hyperactivity. Following food restriction, mice are expected to overeat. However, selecting hyperactive and addiction-related animal models, we observed that mice lacking 5-HTR1B self-imposed food restriction after deprivation and still displayed anorexia and hyperactivity after ecstasy. Decryption of the mechanisms showed a gain-of-function of 5-HTR4 in the absence of 5-HTR1B, associated with CART surplus in the NAc and not in other brain areas. NAc-5-HTR4 overexpression upregulated NAc-CART, provoked anorexia and hyperactivity. NAc-5-HTR4 knockdown or blockade reduced ecstasy-induced hyperactivity. Finally, NAc-CART knockdown suppressed hyperactivity upon stimulation of the NAc-5-HTR4. Additionally, inactivating NAc-5-HTR4 suppressed ecstasy's preference, strengthening the rewarding facet of anorexia. In conclusion, the NAc-5-HTR4/CART pathway establishes a ‘tight-junction' between anorexia and hyperactivity, suggesting the existence of a primary functional unit susceptible to limit overeating associated with resting following homeostasis rules. PMID:23233022

A 3-D inelastic analysis of HTR graphite structures and a comparison with A 2-D approach

International Nuclear Information System (INIS)

Willaschek, J.

1979-01-01

In High Temperature Reactor Cores (HTR) a large number of elements are constructed of nuclear graphite. The dimensions of the graphite components are limited by stresses and strains resulting from thermal loads, irradiation induced dimensional changes and stress-dependent irradiation creep. Therefore it is necessary to examine the feasibility of design concepts with regard to the structural integrity of the material. This paper presents an analysis of a radial reflector concept for use in a 3000 MWth HTR for process heat production. This concept of a pebble bed reactor (OTTO cycle) requires reflector dimensions and shapes which have previously not been used and which may exceed acceptable stress limits. Graphite reflector elements in a HTR are subject to a high fluence of fast neutrons. The fluence varies spatially within an element. Irradiation-induced strains occur which in turn vary non-linearly with the fluence. At low fluences the graphite shrinks. With increasing fluence shrinkage is saturated and after a 'turn-around' point the graphite begins to swell. The net effect of fluence gradient and irradiation-induced strain is a 'necking' of the element which moves radially outwards with time. In this paper a three-dimensional inelastic analysis of a graphite block with the above deformation history is described. The influence of irradiation on dimensional stability and other material properties was taken into account. Numerical results were obtained with the finite-element computer code ADINA, modified at INTERATOM for the task in hand. The radial reflector block was modelled using 21-node three-dimensional continuum elements of elastic-creep material. The element stiffness matrices were calculated using the standard 2x2x2 Gauss integration; material nonlinearities with quadratic displacement functions and linearised initial strains were employed. (orig.)

The chlamydial periplasmic stress response serine protease cHtrA is secreted into host cell cytosol

Directory of Open Access Journals (Sweden)

Flores Rhonda

2011-04-01

Full Text Available Abstract Background The periplasmic High Temperature Requirement protein A (HtrA plays important roles in bacterial protein folding and stress responses. However, the role of chlamydial HtrA (cHtrA in chlamydial pathogenesis is not clear. Results The cHtrA was detected both inside and outside the chlamydial inclusions. The detection was specific since both polyclonal and monoclonal anti-cHtrA antibodies revealed similar intracellular labeling patterns that were only removed by absorption with cHtrA but not control fusion proteins. In a Western blot assay, the anti-cHtrA antibodies detected the endogenous cHtrA in Chlamydia-infected cells without cross-reacting with any other chlamydial or host cell antigens. Fractionation of the infected cells revealed cHtrA in the host cell cytosol fraction. The periplasmic cHtrA protein appeared to be actively secreted into host cell cytosol since no other chlamydial periplasmic proteins were detected in the host cell cytoplasm. Most chlamydial species secreted cHtrA into host cell cytosol and the secretion was not inhibitable by a type III secretion inhibitor. Conclusion Since it is hypothesized that chlamydial organisms possess a proteolysis strategy to manipulate host cell signaling pathways, secretion of the serine protease cHtrA into host cell cytosol suggests that the periplasmic cHtrA may also play an important role in chlamydial interactions with host cells.

Results of a European industrial heat market analysis as a pre-requisite to evaluating the HTR market in Europe and elsewhere

International Nuclear Information System (INIS)

Bredimas, Alexandre

2014-01-01

High temperature nuclear reactors will mainly address the market of industrial cogeneration. This market is a part of the overall market of the heat concretely consumed by industry, in particular heat intensive industries. In simpler terms, the HTR market is a part of the industrial cogeneration market, which itself is a part of the industrial heat market. The EU-supported project EUROPAIRS (2009–2011) has therefore carried out a comprehensive study of the complete European industrial heat market in order to prepare for the deployment of HTRs. This information did not exist priori to the study. The purposes of this paper are (1) to present the methodology of the study and the experience gathered in order to exchange with non-European equivalent or future initiatives (beyond the discussions already engaged with the US), (2) to synthesise the quantitative results of the study and (3) to briefly report on the cogeneration usages in several key industries (e.g. chemicals, refining, steelmaking…) which may affect HTR designing. The paper finishes with some reflection on the part of the heat market that HTRs could potentially address. In correlation with our other paper on the pre-economic analysis, this paper intend to pave the way for an international cooperation on evaluating the market for HTR worldwide, which is an information of common interest to the HTR community

Serotonergic gene polymorphisms (5-HTTLPR, 5HTR1A, 5HTR2A), and population differences in aggression: traditional (Hadza and Datoga) and industrial (Russians) populations compared.

Science.gov (United States)

Butovskaya, Marina L; Butovskaya, Polina R; Vasilyev, Vasiliy A; Sukhodolskaya, Jane M; Fekhredtinova, Dania I; Karelin, Dmitri V; Fedenok, Julia N; Mabulla, Audax Z P; Ryskov, Alexey P; Lazebny, Oleg E

2018-04-16

Current knowledge on genetic basis of aggressive behavior is still contradictory. This may be due to the fact that the majority of studies targeting associations between candidate genes and aggression are conducted on industrial societies and mainly dealing with various types of psychopathology and disorders. Because of that, our study was carried on healthy adult individuals of both sex (n = 853). Three populations were examined: two traditional (Hadza and Datoga) and one industrial (Russians), and the association of aggression with the following polymorphisms 5-HTTLPR, rs6295 (5HTR1A gene), and rs6311 (5HTR2A gene) were tested. Aggression was measured as total self-ratings on Buss-Perry Aggression Questionnaire. Distributions of allelic frequencies of 5-HTTLPR and 5HTR1A polymorphisms were significantly different among the three populations. Consequently, the association analyses for these two candidate genes were carried out separately for each population, while for the 5HTR2A polymorphism, it was conducted on the pooled data that made possible to introduce ethnic factor in the ANOVA model. The traditional biometrical approach revealed no sex differences in total aggression in all three samples. The three-way ANOVA (μ + 5-HTTLPR + 5HTR1A + 5HTR2A +ε) with measures of self-reported total aggression as dependent variable revealed significant effect of the second serotonin receptor gene polymorphism for the Hadza sample. For the Datoga, the interaction effect between 5-HTTLPR and 5HTR1A was significant. No significant effects of the used polymorphisms were obtained for Russians. The results of two-way ANOVA with ethnicity and the 5HTR2A polymorphism as main effects and their interactions revealed the highly significant effect of ethnicity, 5HTR2A polymorphism, and their interaction on total aggression. Our data provided obvious confirmation for the necessity to consider the population origin, as well as cultural background of tested individuals, while

Safety concept of high-temperature reactors based on the experience with AVR and THTR

International Nuclear Information System (INIS)

Wachholz, Winfried; Kroeger, Wolfgang

1990-01-01

In the Federal Republic of Germany a reactor is considered safe if verification has been furnished that the requirements contained in paragraph 7 of the Federal German Atomic Energy Act are met for this reactor: demonstration of sufficient precautions against damage required according to the actual state of the art, and especially compliance with the dose rate limits for normal operation and accidental conditions. These requirements result in a deterministic multi-stage safety concept with specified requirements for the engineered safety systems. In recent years, proposals for enhanced safety of nuclear power reactors or a radical change in safety philosophy have been made. This is characterised by 'inherently safe', 'super safe' and similar slogans. A quantitative definition of these requirements has not yet been established, but it is clear as a common objective that the event of beyond design basis accidents evacuation, relocation, and large scale contamination of ground should not occur. As a consequence of the Chernobyl accident the safety of all the NPPs in Germany has been reviewed. This analysis was completed for the THTR reactor in 1988. The same has been done for AVR reactor. The final evaluation of the HTR specific safety features have been fully confirmed. The HTR concepts under development are based on this experience. The HTR-Modul unit is currently being designed

A fuel performance analysis for a 450 MWth deep burn-high temperature reactor

International Nuclear Information System (INIS)

Kim, Young Min; Jo, Chang Keun; Jun, Ji Su; Cho, Moon Sung; Venneri, Francesco

2011-01-01

Highlights: → We have checked, through a fuel performance analysis, if a 450 MW th high temperature reactor was safe for the deep burn of a TRU fuel. → During a core heat-up event, the fuel temperature was below 1600 deg. C and the maximum gas pressure in the void of coated fuel particle was about 90 MPa. → At elevated temperatures of the accident event, the failure fraction of coated fuel particles resulted from the mechanical failure and the thermal decomposition of the SiC barrier was 3.30 x 10 -3 . - Abstract: A performance analysis for a 450 MW th deep burn-high temperature reactor (DB-HTR) fuel was performed using COPA, a fuel performance analysis code of Korea Atomic Energy Research Institute (KAERI). The code computes gas pressure buildup in the void volume of a tri-isotropic coated fuel particle (TRISO), temperature distribution in a DB-HTR fuel, thermo-mechanical stress in a coated fuel particle (CFP), failure fractions of a batch of CFPs, and fission product (FP) releases into the coolant. The 350 μm DB-HTR kernel is composed of 30% UO 2 + 70% (5% NpO 2 + 95% PuO 1.8 ) mixed with 0.6 moles of silicon carbide (SiC) per mole of heavy metal. The DB-HTR is operated at the constant temperature and power of 858 deg. C and 39.02 mW per CFP for 1395 effective full power days (EFPD) and is subjected to a core heat-up event for 250 h during which the maximum coolant temperature reaches 1548.70 deg. C. Within the normal operating temperature, the fuel showed good thermal and mechanical integrity. At elevated temperatures of the accident event, the failure fraction of CFPs resulted from the mechanical failure (MF) and the thermal decomposition (TD) of the SiC barrier is 3.30 x 10 -3 .

Thermodynamic correlations for the accident analysis of HTR's

International Nuclear Information System (INIS)

Rehm, W.; Jahn, W.; Finken, R.

1976-12-01

The thermal properties of Helium and for the case of a depressurized primary circuit, various mixtures of primary cooling gas were taken into consideration. The temperature dependence of the correlations for the thermal properties of the graphite components in the core and for the structural materials in the primary circuit are extrapolated about normal operation conditions. Furthermore the correlations for the effective thermal conductivity, the heat transfer and pressure drop are described for pebble bed HTR's. In addition some important heat transfer data of the steam generator are included. With these correlations, for example accident sequences with failure of the afterheat removal systems are discussed for pebble bed HTR's. It is concluded that the transient temperature behaviour demonstrates the inherent safety features of the HTR in extreme accidents. (orig.) [de

Hydrogen production by high temperature electrolysis of water vapour and nuclear reactors

International Nuclear Information System (INIS)

Jean-Pierre Py; Alain Capitaine

2006-01-01

This paper presents hydrogen production by a nuclear reactor (High Temperature Reactor, HTR or Pressurized Water Reactor, PWR) coupled to a High Temperature Electrolyser (HTE) plant. With respect to the coupling of a HTR with a HTE plant, EDF and AREVA NP had previously selected a combined cycle HTR scheme to convert the reactor heat into electricity. In that case, the steam required for the electrolyser plant is provided either directly from the steam turbine cycle or from a heat exchanger connected with such cycle. Hydrogen efficiency production is valued using high temperature electrolysis. Electrolysis production of hydrogen can be performed with significantly higher thermal efficiencies by operating in the steam phase than in the water phase. The electrolysis performance is assessed with solid oxide and solid proton electrolysis cells. The efficiency from the three operating conditions (endo-thermal, auto-thermal and thermo-neutral) of a high temperature electrolysis process is evaluated. The technical difficulties to use the gases enthalpy to heat the water are analyzed, taking into account efficiency and technological challenges. EDF and AREVA NP have performed an analysis to select an optimized process giving consideration to plant efficiency, plant operation, investment and production costs. The paper provides pathways and identifies R and D actions to reach hydrogen production costs competitive with those of other hydrogen production processes. (authors)

Waste arisings from a high-temperature reactor with a uranium-thorium fuel cycle

International Nuclear Information System (INIS)

1979-09-01

This paper presents an equilibrium-recycle condition flow sheet for a high-temperature gas-cooled reactor (HTR) fuel cycle which uses thorium and high-enriched uranium (93% U-235) as makeup fuel. INFCE Working Group 7 defined percentage losses to various waste streams are used to adjust the heavy-element mass flows per gigawatt-year of electricity generated. Thorium and bred U-233 are recycled following Thorex reprocessing. Fissile U-235 is recycled one time following Purex reprocessing and then is discarded to waste. Plutonium and other transuranics are discarded to waste. Included are estimates of volume, radioactivity, and heavy-element content of wastes arising from HTR fuel element fabrication; HTR operation, maintenance, and decommissioning; and reprocessing spent fuel where the waste is unique to the HTR fuel cycle

Euratom research and training in generation IV systems with emphasis on V/HTR

International Nuclear Information System (INIS)

Goethem, G. van; Manolatos, P.; Fuetterer, M.

2006-01-01

In this overview paper, the following questions are addressed: (1) What are the challenges facing the European Union nuclear fission research community in the short (today), medium (2010) and long term (2040)? (2) What kind of research and technological development (RTD) does Euratom offer to respond to these challenges, in particular in the area of reactor systems and fuel cycles? In the general debate about energy supply technologies there are challenges of both a scientific and technological (S/T) as well as an economic and political (E/P) nature. Though the Community research programme acts mainly on the former, there is nevertheless important links with Community policy. These not only exist in the specific area of nuclear policy. It is shown in the particular area of nuclear fission, to what extent Euratom research, education and innovation ('Knowledge Triangle: Education, Research, and Innovation') respond to the S/T challenges: (1) sustainability, (2) economics, (3) safety, and (4) proliferation resistance. At the European Commission (EC), the research related to nuclear reactor systems and fuel cycles is principally under the responsibility of the 2 Directorates Generals (DG) DG Research (RTD, located in Brussels), which implements and manages the programme of 'indirect actions', and the DG Joint Research Centre (JRC, headquarters in Brussels and 7 scientific institutes in 5 Member States) which carries out 'direct actions' in their own laboratories. In this HTR-2006 introductory paper, the emphasis is on the indirect and direct actions of the 6 th Euratom research framework programme 2003-2006, FP-6, with special emphasis on V/HTR Generation IV research. (orig.)

Fission product behaviour in the primary circuit of an HTR

International Nuclear Information System (INIS)

Decken, C.B. von der; Iniotakis, N.

1981-01-01

The knowledge of fission product behaviour in the primary circuit of a High Temperature Reactor (HTR) is an essential requirement for the estimations of the availability of the reactor plant in normal operation, of the hazards to personnel during inspection and repair and of the potential danger to the environment from severe accidents. On the basis of the theoretical and experimental results obtained at the ''Institute for Reactor Components'' of the KFA Juelich /1/,/2/ the transport- and deposition behaviour of the fission- and activation products in the primary circuit of the PNP-500 reference plant has been investigated thoroughly. Special work had been done to quantify the uncertainties of the investigations and to calculate or estimate the dose rate level at different components of the primary cooling circuit. The contamination and the dose rate level in the inspection gap in the reactor pressure vessel is discussed in detail. For these investigations in particular the surface structure and the composition of the material, the chemical state of the fission products in the cooling gas, the composition of the cooling gas and the influence of dust on the transport- and deposition behaviour of the fission products have been taken into account. The investigations have been limited to the nuclides Ag-110m; Cs-134 and Cs-137

Studies on the behavior of graphite structures irradiated in the Dragon Reactor. Dragon Project report

Energy Technology Data Exchange (ETDEWEB)

Everett, M. R.; Graham, L. W.; Ridealgh, F.

1971-11-15

Design data for the physical and mechanical property changes which occur in graphite structural and fuel body components irradiated in an HTR are largely obtained from small specimens tested in the laboratory and in materials test reactors. A brief data summary is given. This graphite physics data can be used to predict dimensional changes, internal stress generation and strength changes in the graphite materials of HTR fuel elements irradiated in the Dragon Reactor. In this paper, the results which have been obtained from post-irradiation examination of a number of fuel pins, are compared with prediction.

The market for HTGR type reactors

International Nuclear Information System (INIS)

Roehler, E.

1986-01-01

High-temperature-reactors with pebble-bed-reactor cores as a progressive reactor line, have been developed by BBC/HRB the Federal Republic of Germany over a period of 27 years and will soon be mature to be introduced to the market. They represent an important innovation in the field of reactor engineering. Due to its high degree of applicability on the power and heat market and its high flexibility regarding the site and fuel cycle the HTR is extremely suitable for providing energy to consumers, especially in countries using nuclear energy supply for the first time. (orig.) [de

Abrasion behavior of graphite pebble in lifting pipe of pebble-bed HTR

Energy Technology Data Exchange (ETDEWEB)

Shen, Ke; Su, Jiageng [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Zhou, Hongbo [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Chinergy Co., LTD., Beijing 100193 (China); Peng, Wei; Liu, Bing [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Yu, Suyun, E-mail: suyuan@tsinghua.edu.cn [Center for Combustion Energy, The Key Laboratory for Thermal Science and Power Engineering, Ministry of Educations, Tsinghua University, Beijing 10084 (China)

2015-11-15

Highlights: • Quantitative determination of abrasion rate of graphite pebbles in different lifting velocities. • Abrasion behavior of graphite pebble in helium, air and nitrogen. • In helium, intensive collisions caused by oscillatory motion result in more graphite dust production. - Abstract: A pebble-bed high-temperature gas-cooled reactor (pebble-bed HTR) uses a helium coolant, graphite core structure, and spherical fuel elements. The pebble-bed design enables on-line refueling, avoiding refueling shutdowns. During circulation process, the pebbles are lifted pneumatically via a stainless steel lifting pipe and reinserted into the reactor. Inevitably, the movement of the fuel elements as they recirculate in the reactor produces graphite dust. Mechanical wear is the primary source of graphite dust production. Specifically, the sources are mechanisms of pebble–pebble contact, pebble–wall (structural graphite) contact, and fuel handling (pebble–metal abrasion). The key contribution to graphite dust production is from the fuel handling system, particularly from the lifting pipe. During pneumatic lift, graphite pebbles undergo multiple collisions with the stainless steel lifting pipe, thereby causing abrasion of the graphite pebbles and producing graphite dust. The present work explored the abrasion behavior of graphite pebble in the lifting pipe by measuring the abrasion rate at different lifting velocities. The abrasion rate of the graphite pebble in helium was found much higher than those in air and nitrogen. This gas environment effect could be explained by either tribology behavior or dynamic behavior. Friction testing excluded the possibility of tribology reason. The dynamic behavior of the graphite pebble was captured by analysis of the audio waveforms during pneumatic lift. The analysis results revealed unique dynamic behavior of the graphite pebble in helium. Oscillation and consequently intensive collisions occur during pneumatic lift, causing

Study on the profitableness of electricity generation with high temperature reactors

International Nuclear Information System (INIS)

Kolb, G.

1978-08-01

The programme group 'Systemforschung und Technologische Entwicklung' (STE) of the Nuclear Research Centre Juelich in cooperation with the internal institutions 'Projekttraegerschaft Entwicklung von Hochtemperaturreaktoren' (PTH) and 'Institut fuer Reaktorentwicklung' (IRE) on the one hand, and the external partner 'Hochtemperatur-Reactorbau GmbH' (HRB) and 'Gesellschaft fuer Hochtemperaturreactor Technik' (GHT) on the other hand have set up a study on fuel cycle costs, electricity production cost and the economical use as well as uranium resource protection by introduction of high temperature reactors (HTR) with pebble bed core to generate electricity. The pressurized-water reactor (PWR) today on the market serves as comparison. The working results obtained sofar are compiled in the present report. It was particularly noted that - the HTR can economically fully compete with the PWR for electricity generation - the necessary supply of natural uranium for the HTR in open circuit is about one third lower and in the closed circuit, almost two thirds lower than in the corresponding PWR. A further reduction is possible on a long-term basis by highly converting HTW systems. (orig.) [de

Thorium-Based Fuel Cycles in the Modular High Temperature Reactor

Institute of Scientific and Technical Information of China (English)

CHANG Hong; YANG Yongwei; JING Xingqing; XU Yunlin

2006-01-01

Large stockpiles of civil-grade as well as weapons-grade plutonium have been accumulated in the world from nuclear power or other programs of different countries. One alternative for the management of the plutonium is to incinerate it in the high temperature reactor (HTR). The thorium-based fuel cycle was studied in the modular HTR to reduce weapons-grade plutonium stockpiles, while producing no additional plutonium or other transuranic elements. Three thorium-uranium fuel cycles were also investigated. The thorium absorption cross sections of the resolved and unresolved resonances were generated using the ZUT-DGL code based on existing resonance data. The equilibrium core of the modular HTR was calculated and analyzed by means of the code VSOP'94. The results show that the modular HTR can incinerate most of the initially loaded plutonium amounting to about 95.3% net 239Pu for weapons-grade plutonium and can effectively utilize the uranium and thorium in the thorium-uranium fuel cycles.

On the correctness of the thermoluminescent high-temperature ratio (HTR) method for estimating ionization density effects in mixed radiation fields

International Nuclear Information System (INIS)

Bilski, Pawel

2010-01-01

The high-temperature ratio (HTR) method which exploits changes in the LiF:Mg,Ti glow-curve due to high-LET radiation, has been used for several years to estimate LET in an unknown radiation field. As TL efficiency is known to decrease after doses of densely ionizing radiation, a LET estimate is used to correct the TLD-measured values of dose. The HTR method is purely empirical and its general correctness is questionable. The validity of the HTR method was investigated by theoretical simulation of various mixed radiation fields. The LET eff values estimated with the HTR method for mixed radiation fields were found in general to be incorrect, in some cases underestimating the true values of dose-averaged LET by an order of magnitude. The method produced correct estimates of average LET only in cases of almost mono-energetic fields (i.e. in non-mixed radiation conditions). The value of LET eff found by the HTR method may therefore be treated as a qualitative indicator of increased LET, but not as a quantitative estimator of average LET. However, HTR-based correction of the TLD-measured dose value (HTR-B method) was found to be quite reliable. In all cases studied, application of this technique improved the result. Most of the measured doses fell within 10% of the true values. A further empirical improvement to the method is proposed. One may therefore recommend the HTR-B method to correct for decreased TL efficiency in mixed high-LET fields.

Gas reactor international cooperative program interim report. Pebble bed reactor fuel cycle evaluation

International Nuclear Information System (INIS)

1978-09-01

Nuclear fuel cycles were evaluated for the Pebble Bed Gas Cooled Reactor under development in the Federal Republic of Germany. The basic fuel cycle specified for the HTR-K and PNP is well qualified and will meet the requirements of these reactors. Twenty alternate fuel cycles are described, including high-conversion cycles, net-breeding cycles, and proliferation-resistant cycles. High-conversion cycles, which have a high probability of being successfully developed, promise a significant improvement in resource utilization. Proliferation-resistant cycles, also with a high probability of successful development, compare very favorably with those for other types of reactors. Most of the advanced cycles could be adapted to first-generation pebble bed reactors with no significant modifications

Temperature Analysis and Failure Probability of the Fuel Element in HTR-PM

International Nuclear Information System (INIS)

Yang Lin; Liu Bing; Tang Chunhe

2014-01-01

Spherical fuel element is applied in the 200-MW High Temperature Reactor-Pebble-bed Modular (HTR-PM). Each spherical fuel element contains approximately 12,000 coated fuel particles in the inner graphite matrix with a diameter of 50mm to form the fuel zone, while the outer shell with a thickness of 5mm is a fuel-free zone made up of the same graphite material. Under high burnup irradiation, the temperature of fuel element rises and the stress will result in the damage of fuel element. The purpose of this study is to analyze the temperature of fuel element and to discuss the stress and failure probability. (author)

Genetic variation in HTR4 and lung function: GWAS follow-up in mouse.

Science.gov (United States)

House, John S; Li, Huiling; DeGraff, Laura M; Flake, Gordon; Zeldin, Darryl C; London, Stephanie J

2015-01-01

Human genome-wide association studies (GWASs) have identified numerous associations between single nucleotide polymorphisms (SNPs) and pulmonary function. Proving that there is a causal relationship between GWAS SNPs, many of which are noncoding and without known functional impact, and these traits has been elusive. Furthermore, noncoding GWAS-identified SNPs may exert trans-regulatory effects rather than impact the proximal gene. Noncoding variants in 5-hydroxytryptamine (serotonin) receptor 4 (HTR4) are associated with pulmonary function in human GWASs. To gain insight into whether this association is causal, we tested whether Htr4-null mice have altered pulmonary function. We found that HTR4-deficient mice have 12% higher baseline lung resistance and also increased methacholine-induced airway hyperresponsiveness (AHR) as measured by lung resistance (27%), tissue resistance (48%), and tissue elastance (30%). Furthermore, Htr4-null mice were more sensitive to serotonin-induced AHR. In models of exposure to bacterial lipopolysaccharide, bleomycin, and allergic airway inflammation induced by house dust mites, pulmonary function and cytokine profiles in Htr4-null mice differed little from their wild-type controls. The findings of altered baseline lung function and increased AHR in Htr4-null mice support a causal relationship between genetic variation in HTR4 and pulmonary function identified in human GWAS. © FASEB.

The ARCHER project (Advanced High-Temperature Reactors for Cogeneration of Heat and Electricity R&D)

Energy Technology Data Exchange (ETDEWEB)

Knol, S., E-mail: knol@nrg.eu [Nuclear Research and consultancy Group (NRG), PO Box 25, NL-1755 ZG Petten (Netherlands); Fütterer, M.A. [Joint Research Centre, Institute for Energy, Petten (Netherlands); Roelofs, F. [Nuclear Research and consultancy Group (NRG), PO Box 25, NL-1755 ZG Petten (Netherlands); Kohtz, N. [TÜV Rheinland, Köln (Germany); Laurie, M. [Joint Research Centre, Institute for Transuranium elements, Karlsruhe (Germany); Buckthorpe, D. [UMAN, University of Manchester, Manchester (United Kingdom); Scheuermann, W. [IKE, Stuttgart University, Stuttgart (Germany)

2016-09-15

The European HTR R&D project ARCHER (Advanced High-Temperature Reactors for Cogeneration of Heat and Electricity R&D) builds on a solid HTR technology foundation in Europe, established through former national UK and German HTR programs and in European framework programs. ARCHER runs from 2011 to 2015 and targets selected HTR R&D subjects that would specifically support demonstration, with a focus on experimental effort. In line with the R&D and deployment strategy of the European Sustainable Nuclear Energy Technology Platform (SNETP) ARCHER contributes to maintaining, strengthening and expanding the HTR knowledge base in Europe to lay the foundations for demonstration of nuclear cogeneration with HTR systems. The project consortium encompasses conventional and nuclear industry, utilities, Technical Support Organizations, R&D organizations and academia. ARCHER shares results with international partners in the Generation IV International Forum and collaborates directly with related projects in the US, China, Japan, the Republic of Korea and South Africa. The ARCHER project has finished, and the paper comprises an overview of the achievements of the project.

High temperature engineering research facilities and experiments in China

International Nuclear Information System (INIS)

Xu, Yuanhui; Liu, Meisheng; Yao, Huizhong; Ju, Huaiming

1998-01-01

June 14, 1995, the construction of a pebble bed type high temperature gas-cooled reactor (HTGR) started in China. It is a test reactor with 10 MW thermal power output (termed HTR- 10). The test reactor is located on the site of Institute of Nuclear Energy Technology (INET) of Tsinghua University in the northwest suburb of Beijing, about 40 km away from the city. Design of the HTR-10 test reactor represents the features of HTR-Modular design: 'side-by-side' arrangement, spherical fuel elements with 'multi-pass' loading scheme, completely passive decay heat removal, reactor shutdown systems in the side reflector, etc. However, in the HTR-10 design some modifications from the HTR-Module were made to satisfy Chinese conditions. For example, the steam generator is composed of a number of modular helical tubes with small diameter, pulse pneumatic discharging apparatus are used in the fuel handling system and step motor driving control rods are designed. These modifications would cause some uncertainty in our design. It is necessary to do engineering experiments to prove these new or modified ideas. Therefore, a program of engineering experiments for HTR-10 key technologies is being conducted at INET. The main aims of these engineering experiments are to verify the designed characteristics and performance of the components and systems, to feedback on design and to obtain operational experiences. Those engineering experiments are depressurization test of the hot gas duct at room temperature and operating pressure, performance test of the hot gas duct at operating helium temperature and pressure, performance test of the pulse pneumatic fuel handling system, test of the control rods driving apparatus, two phase flow stability test for the once through steam generator and cross mixture test at the bottom of the reactor core

A global model for gas cooled reactors for the Generation-4: application to the Very High Temperature Reactor (VHTR)

International Nuclear Information System (INIS)

Limaiem, I.

2006-12-01

Gas cooled high temperature reactor (HTR) belongs to the new generation of nuclear power plants called Generation IV. The Generation IV gathers the entire future nuclear reactors concept with an effective deployment by 2050. The technological choices relating to the nature of the fuel, the moderator and the coolant as well as the annular geometry of the core lead to some physical characteristics. The most important of these characteristics is the very strong thermal feedback in both active zone and the reflectors. Consequently, HTR physics study requires taking into account the strong coupling between neutronic and thermal hydraulics. The work achieved in this Phd consists in modeling, programming and studying of the neutronic and thermal hydraulics coupling system for block type gas cooled HTR. The coupling system uses a separate resolution of the neutronic and thermal hydraulics problems. The neutronic scheme is a double level Transport (APOLLO2) /Diffusion (CRONOS2) scheme respectively on the scale of the fuel assembly and a reactor core scale. The thermal hydraulics model uses simplified Navier Stokes equations solved in homogeneous porous media in code CAST3M CFD code. A generic homogenization model is used to calculate the thermal hydraulics parameters of the porous media. A de-homogenization model ensures the link between the porous media temperatures of the temperature defined in the neutronic model. The coupling system is made by external procedures communicating between the thermal hydraulics and neutronic computer codes. This Phd thesis contributed to the Very High Temperature Reactor (VHTR) physics studies. In this field, we studied the VHTR core in normal operating mode. The studies concern the VHTR core equilibrium cycle with the control rods and using the neutronic and thermal hydraulics coupling system. These studies allowed the study of the equilibrium between the power, the temperature and Xenon. These studies open new perspective for core

Evolution of mitochondrial cell death pathway: Proapoptotic role of HtrA2/Omi in Drosophila

International Nuclear Information System (INIS)

Igaki, Tatsushi; Suzuki, Yasuyuki; Tokushige, Naoko; Aonuma, Hiroka; Takahashi, Ryosuke; Miura, Masayuki

2007-01-01

Despite the essential role of mitochondria in a variety of mammalian cell death processes, the involvement of mitochondrial pathway in Drosophila cell death has remained unclear. To address this, we cloned and characterized DmHtrA2, a Drosophila homolog of a mitochondrial serine protease HtrA2/Omi. We show that DmHtrA2 normally resides in mitochondria and is up-regulated by UV-irradiation. Upon receipt of apoptotic stimuli, DmHtrA2 is translocated to extramitochondrial compartment; however, unlike its mammalian counterpart, the extramitochondrial DmHtrA2 does not diffuse throughout the cytosol but stays near the mitochondria. RNAi-mediated knock-down of DmHtrA2 in larvae or adult flies results in a resistance to stress stimuli. DmHtrA2 specifically cleaves Drosophila inhibitor-of-apoptosis protein 1 (DIAP1), a cellular caspase inhibitor, and induces cell death both in vitro and in vivo as potent as other fly cell death proteins. Our observations suggest that DmHtrA2 promotes cell death through a cleavage of DIAP1 in the vicinity of mitochondria, which may represent a prototype of mitochondrial cell death pathway in evolution

Effect of the type of mineral aggregate on the high-temperature creep of HTR-concrete

International Nuclear Information System (INIS)

Diederichs, U.; Becker, G.

1989-01-01

Within the scope of the research and development work for the prestressed concrete vessel of the HTR 500 High-Temperature Reactor mix design, manufacture as well as mechanical and thermal behavior of the concrete have been comprehensively studied. Of the concrete types analyzed, a basalt concrete showed extremely favorable high-temperature characteristics while a concrete with Rhine gravel was characterized by a good workability. These two types of concrete were subjected to numerous tests, whereby the testing procedures were strongly related to the anticipated combined stress, temperature and moisture conditions in the real structure

Measurement of fission gases released by HTR irradiation samples in the BR 2 reactor (Mol/Belgium)

International Nuclear Information System (INIS)

Koetter, H.; Mueller, H.B.

1975-04-01

During the irradiation of HTR-test fuel (coated particles resp. compacts) the release rate of fission gases is measured automatically. For that purpose the γ-spectrum of the sweep gas is analyzed with respect to the isotopes Xe-133, Xe-135, Xe-135sup(m), Xe-137, Xe-138, Kr-85sup(m), Kr-87, Kr-88, Kr-89. Gas sampling, spectral analysis, data handling and evaluation are controlled by computer. (orig.) [de

Commissioning of the THTR-300-MWe prototype power plant - A milestone for further application of this high-temperature reactor line

International Nuclear Information System (INIS)

Simon, M.; Baust, E.; Schoening, J.

1986-10-01

With the completion of the THTR 300 and the development of the follow-on plant HTR 500, the BBC/HRB company group has taken the pebble bed high-temperature reactor to the threshold of the commercial stage. The HTR is an important innovation in the field of reactor technology which can play an important role in the intermediate and long-term supply of safe, environmental friendly and economic energy. The power level of 550 MW meets the requirements of the present energy market which shows a trend towards smaller power units as a result of grid size, investment effort, and the slower increase in electricity demand in industrial nations. The advantages of the high-temperature reactor, such as high thermal efficiency, low waste heat, low radiation exposure of operating and maintenance personnel, high inherent safety, simple mode of operation, flexible fuel cycle with the potential to extend fuel resources, high availability, are currently uncontested and will represent the future standards for the peaceful uses of nuclear energy. For special applications in industry (steam and electric power as a cogeneration product) and in case of special siting conditions (near industrial centers), BBC/HRB developed a small 100 MW HTR, which can also be constructed as a 200 MW twin plant at favorable cost conditions. For an economic use of domestic coal in a processed form, the HTR represents the optimum solution as to economic and environmental aspects as well as extension of resources, especially if combined with conventional gasification procedures and in direct application of nuclear process heat at high gas temperatures of about 950 deg. C. In this field the development of the heat-exchanging components remains to be completed, before commercial application will be possible. The HTR is particularly well suited for erection in developing countries and industrial threshold countries which turn to nuclear energy for the first time. On an international level the interest in the

Automatic X-ray inspection for the HTR-PM spherical fuel elements

Energy Technology Data Exchange (ETDEWEB)

Yi, DU, E-mail: duyi11@mails.tsinghua.edu.cn [Institute of Nuclear and New Energy Technology (INET), Tsinghua University, Energy Science Building A309, Haidian District, Beijing 100084 (China); Xiangang, WANG, E-mail: wangxiangang@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology (INET), Tsinghua University, Energy Science Building A309, Haidian District, Beijing 100084 (China); Xincheng, XIANG, E-mail: inetxxc@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology (INET), Tsinghua University, Energy Science Building, Haidian District, Beijing 100084 (China); Bing, LIU, E-mail: bingliu@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology (INET), Tsinghua University, Energy Science Building, Haidian District, Beijing 100084 (China)

2014-12-15

Highlights: • An automatic X-ray inspection method is established to characterize HTR pebbles. • The method provides physical characterization and the inner structure of pebbles. • The method can be conducted non-destructively, quickly and automatically. • Sample pebbles were measured with this AXI method for validation. • The method shows the potential to be applied in situ. - Abstract: Inefficient quality assessment and control (QA and C) of spherical fuel elements for high temperature reactor-pebblebed modules (HTR-PM) has been a long-term problem, since conventional methods are labor intensive and cannot reveal the inside information nondestructively. Herein, we proposed a nondestructive, automated X-ray inspection (AXI) method to characterize spherical fuel elements including their inner structures based on X-ray digital radiography (DR). Briefly, DR images at different angles are first obtained and then the chosen important parameters such as spherical diameters, geometric and mass centers, can be automatically extracted and calculated via image processing techniques. Via evaluating sample spherical fuel elements, we proved that this AXI method can be conducted non-destructively, quickly and automatically. This method not only provides accurate physical characterization of spherical fuel elements but also reveals their inner structure with good resolution, showing great potentials to facilitate fast QA and C in HTM-PM spherical fuel element development and production.

Automatic X-ray inspection for the HTR-PM spherical fuel elements

International Nuclear Information System (INIS)

Yi, DU; Xiangang, WANG; Xincheng, XIANG; Bing, LIU

2014-01-01

Highlights: • An automatic X-ray inspection method is established to characterize HTR pebbles. • The method provides physical characterization and the inner structure of pebbles. • The method can be conducted non-destructively, quickly and automatically. • Sample pebbles were measured with this AXI method for validation. • The method shows the potential to be applied in situ. - Abstract: Inefficient quality assessment and control (QA and C) of spherical fuel elements for high temperature reactor-pebblebed modules (HTR-PM) has been a long-term problem, since conventional methods are labor intensive and cannot reveal the inside information nondestructively. Herein, we proposed a nondestructive, automated X-ray inspection (AXI) method to characterize spherical fuel elements including their inner structures based on X-ray digital radiography (DR). Briefly, DR images at different angles are first obtained and then the chosen important parameters such as spherical diameters, geometric and mass centers, can be automatically extracted and calculated via image processing techniques. Via evaluating sample spherical fuel elements, we proved that this AXI method can be conducted non-destructively, quickly and automatically. This method not only provides accurate physical characterization of spherical fuel elements but also reveals their inner structure with good resolution, showing great potentials to facilitate fast QA and C in HTM-PM spherical fuel element development and production

Steroid hormones modulate galectin-1 in the trophoblast HTR-8/SVneocell line

Directory of Open Access Journals (Sweden)

Bojić-Trbojević Žanka

2008-01-01

Full Text Available The effects of steroids on galectin-1 (gal-1 were studied in HTR-8/SVneo cells by immunocytochemistry, cell-based ELISA, the MTT proliferation test and the Matrigel TM invasion test. Dexamethasone (DEX, progesterone (PRG, and mifepristone (RU486 were used. Gal-1 was modulated in a steroid- and dose-dependent manner by DEX, which mildly but significantly stimulated production at low concentrations (0.1-10 nM, and inhibited it at 100 nM, while the effects of PRG and RU486 were opposite. HTR-8/SVneo cell invasion of Matrigel was significantly decreased in the presence of DEX and lactose. The obtained data support the proposed regulatory role of steroids in trophoblast gal-1 production.

New reactor concepts. An analysis of the actual research status; Neue Reaktorkonzepte. Eine Analyse des aktuellen Forschungsstands

Energy Technology Data Exchange (ETDEWEB)

Pistner, Christoph; Englert, Matthias

2017-04-15

The report on new reactor concepts covers the following issues: characterization and survey of new reactor concepts; evaluation criteria: safety, resources for fuel supply, waste problems, economy and proliferation; comprehensive relevant aspects: thorium as alternative resource, partitioning and transmutation; actual developments and preliminary experiences for fast breeding reactor (FBR), high-temperature reactor (HTR), molten salt reactor (MSR), small modular reactor (SMR).

Study of the HTGR fission product migration at the Osiris experimental reactor

International Nuclear Information System (INIS)

Homme, A. l'; Lucot, M.

1977-01-01

A program of study on accidents in HTR reactor operation is presented: blowdown of primary coolant circuit, water inlet into the primary circuit, fuel element overheating by pipe logging or loss of cooling. These studies will be made in Aida irradiation loop in the pool of the Osiris reactor [fr

CEA and AREVA R and D on V/HTR fuel fabrication with the CAPRI experimental manufacturing line

International Nuclear Information System (INIS)

Charollais, Francois; Fonquernie, Sophie; Perrais, Christophe; Perez, Marc; Cellier, Francois; Vitali, Marie-Pierre

2006-01-01

In the framework of the French V/HTR fuel development and qualification program, the Commissariat a l'Energie Atomique (CEA) and AREVA through its program called ANTARES (Areva New Technology for Advanced Reactor Energy Supply) conduct R and D projects covering the mastering of UO 2 coated particle and fuel compact fabrication technology. To fulfill this task, a review of past knowledge, of existing technologies and a preliminary laboratory scale work program have been conducted with the aim of retrieving the know-how on HTR coated particle and compact manufacture: - The different stages of UO 2 kernel fabrication GSP Sol-Gel process have been reviewed, reproduced and improved; - The experimental conditions for the chemical vapour deposition (CVD) of coatings have been defined on dummy kernels and development of innovative characterization methods has been carried out; - Former CERCA compacting process has been reviewed and updated. In parallel, an experimental manufacturing line for coated particles, named GAIA, and a compacting line based on former CERCA compacting experience have been designed, constructed and are in operation since early 2005 at CEA Cadarache and CERCA Romans, respectively. These two facilities constitute the CAPRI line (CEA and AREVA PRoduction Integrated line). The major objectives of the CAPRI line are: - to recover and validate past knowledge; - to permit the optimisation of reference fabrication processes for kernels and coatings and the investigation of alternative and innovative fuel design (UCO kernel, ZrC coating); - to test alternative compact process options; - to fabricate and characterize fuel required for irradiation and qualification purpose; - to specify needs for the fabrication of representative V/HTR TRISO fuel meeting industrial standards. This paper presents the progress status of the R and D conducted on V/HTR fuel particle and compact manufacture by mid 2005. (authors)

Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors. Publishable Final Activity Report

International Nuclear Information System (INIS)

Kuijper, J.C.; Somers, J.; Van Den Durpel, L.; Chauvet, V.; Cerullo, N.; Cetnar, J.; Abram, T.; Bakker, K.; Bomboni, E.; Bernnat, W.; Domanska, J.G.; Girardi, E.; De Haas, J.B.M.; Hesketh, K.; Hiernaut, J.P.; Hossain, K.; Jonnet, J.; Kim, Y.; Kloosterman, J.L.; Kopec, M.; Murgatroyd, J.; Millington, D.; Lecarpentier, D.; Lomonaco, G.; McEachern, D.; Meier, A.; Mignanelli, M.; Nabielek, H.; Oppe, J.; Petrov, B.Y.; Pohl, C.; Ruetten, H.J.; Schihab, S.; Toury, G.; Trakas, C.; Venneri, F.; Verfondern, K.; Werner, H.; Wiss, T.; Zakova, J.

2010-11-01

The PUMA project -the acronym stands for 'Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors'- was a Specific Targeted Research Project (STREP) within the EURATOM 6th Framework Program (EU FP6). The PUMA project ran from September 1, 2006, until August 31, 2009, and was executed by a consortium of 14 European partner organisations and one from the USA. This report serves 2 purposes. It is both the 'Publishable Final Activity Report' and the 'Final (Summary) Report', describing, per Work Package, the specific objectives, research activities, main conclusions, recommendations and supporting documents. PUMA's main objective was to investigate the possibilities for the utilisation and transmutation of plutonium and especially minor actinides in contemporary and future (high temperature) gas-cooled reactor designs, which are promising tools for improving the sustainability of the nuclear fuel cycle. This contributes to the reduction of Pu and MA stockpiles, and also to the development of safe and sustainable reactors for CO 2 -free energy generation. The PUMA project has assessed the impact of the introduction of Pu/MA-burning HTRs at three levels: fuel and fuel performance (modelling), reactor (transmutation performance and safety) and reactor/fuel cycle facility park. Earlier projects already indicated favourable characteristics of HTRs with respect to Pu burning. So, core physics of Pu/MA fuel cycles for HTRs has been investigated to study the CP fuel and reactor characteristics and to assure nuclear stability of a Pu/MA HTR core, under both normal and abnormal operating conditions. The starting point of this investigation comprised the two main contemporary HTR designs, viz. the pebble-bed type HTR, represented by the South-African PBMR, and hexagonal block type HTR, represented by the GT-MHR. The results (once again) demonstrate the flexibility of the contemporary (and near future) HTR designs and their ability to accept a

Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors. Publishable Final Activity Report

Energy Technology Data Exchange (ETDEWEB)

Kuijper, J.C., E-mail: kuijper@nrg.eu [Nuclear Research and Consultancy Group (NRG), Petten (Netherlands); Somers, J; Van Den Durpel, L; Chauvet, V; Cerullo, N; Cetnar, J; Abram, T; Bakker, K; Bomboni, E; Bernnat, W; Domanska, J G; Girardi, E; De Haas, J B.M.; Hesketh, K; Hiernaut, J P; Hossain, K; Jonnet, J; Kim, Y; Kloosterman, J L; Kopec, M; Murgatroyd, J; Millington, D; Lecarpentier, D; Lomonaco, G; McEachern, D; Meier, A; Mignanelli, M; Nabielek, H; Oppe, J; Petrov, B Y; Pohl, C; Ruetten, H J; Schihab, S; Toury, G; Trakas, C; Venneri, F; Verfondern, K; Werner, H; Wiss, T; Zakova, J

2010-11-15

The PUMA project -the acronym stands for 'Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors'- was a Specific Targeted Research Project (STREP) within the EURATOM 6th Framework Program (EU FP6). The PUMA project ran from September 1, 2006, until August 31, 2009, and was executed by a consortium of 14 European partner organisations and one from the USA. This report serves 2 purposes. It is both the 'Publishable Final Activity Report' and the 'Final (Summary) Report', describing, per Work Package, the specific objectives, research activities, main conclusions, recommendations and supporting documents. PUMA's main objective was to investigate the possibilities for the utilisation and transmutation of plutonium and especially minor actinides in contemporary and future (high temperature) gas-cooled reactor designs, which are promising tools for improving the sustainability of the nuclear fuel cycle. This contributes to the reduction of Pu and MA stockpiles, and also to the development of safe and sustainable reactors for CO{sub 2}-free energy generation. The PUMA project has assessed the impact of the introduction of Pu/MA-burning HTRs at three levels: fuel and fuel performance (modelling), reactor (transmutation performance and safety) and reactor/fuel cycle facility park. Earlier projects already indicated favourable characteristics of HTRs with respect to Pu burning. So, core physics of Pu/MA fuel cycles for HTRs has been investigated to study the CP fuel and reactor characteristics and to assure nuclear stability of a Pu/MA HTR core, under both normal and abnormal operating conditions. The starting point of this investigation comprised the two main contemporary HTR designs, viz. the pebble-bed type HTR, represented by the South-African PBMR, and hexagonal block type HTR, represented by the GT-MHR. The results (once again) demonstrate the flexibility of the contemporary (and near future) HTR designs and their ability to accept a

Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors. Publishable Final Activity Report

Energy Technology Data Exchange (ETDEWEB)

Kuijper, J.C., E-mail: kuijper@nrg.eu [Nuclear Research and Consultancy Group (NRG), Petten (Netherlands); Somers, J.; Van Den Durpel, L.; Chauvet, V.; Cerullo, N.; Cetnar, J.; Abram, T.; Bakker, K.; Bomboni, E.; Bernnat, W.; Domanska, J.G.; Girardi, E.; De Haas, J.B.M.; Hesketh, K.; Hiernaut, J.P.; Hossain, K.; Jonnet, J.; Kim, Y.; Kloosterman, J.L.; Kopec, M.; Murgatroyd, J.; Millington, D.; Lecarpentier, D.; Lomonaco, G.; McEachern, D.; Meier, A.; Mignanelli, M.; Nabielek, H.; Oppe, J.; Petrov, B.Y.; Pohl, C.; Ruetten, H.J.; Schihab, S.; Toury, G.; Trakas, C.; Venneri, F.; Verfondern, K.; Werner, H.; Wiss, T.; Zakova, J.

2010-11-15

The PUMA project -the acronym stands for 'Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors'- was a Specific Targeted Research Project (STREP) within the EURATOM 6th Framework Program (EU FP6). The PUMA project ran from September 1, 2006, until August 31, 2009, and was executed by a consortium of 14 European partner organisations and one from the USA. This report serves 2 purposes. It is both the 'Publishable Final Activity Report' and the 'Final (Summary) Report', describing, per Work Package, the specific objectives, research activities, main conclusions, recommendations and supporting documents. PUMA's main objective was to investigate the possibilities for the utilisation and transmutation of plutonium and especially minor actinides in contemporary and future (high temperature) gas-cooled reactor designs, which are promising tools for improving the sustainability of the nuclear fuel cycle. This contributes to the reduction of Pu and MA stockpiles, and also to the development of safe and sustainable reactors for CO{sub 2}-free energy generation. The PUMA project has assessed the impact of the introduction of Pu/MA-burning HTRs at three levels: fuel and fuel performance (modelling), reactor (transmutation performance and safety) and reactor/fuel cycle facility park. Earlier projects already indicated favourable characteristics of HTRs with respect to Pu burning. So, core physics of Pu/MA fuel cycles for HTRs has been investigated to study the CP fuel and reactor characteristics and to assure nuclear stability of a Pu/MA HTR core, under both normal and abnormal operating conditions. The starting point of this investigation comprised the two main contemporary HTR designs, viz. the pebble-bed type HTR, represented by the South-African PBMR, and hexagonal block type HTR, represented by the GT-MHR. The results (once again) demonstrate the flexibility of the contemporary (and near future) HTR

SuPer-Homogenization (SPH) Corrected Cross Section Generation for High Temperature Reactor

Energy Technology Data Exchange (ETDEWEB)

Sen, Ramazan Sonat [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hummel, Andrew John [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hiruta, Hikaru [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-03-01

The deterministic full core simulators require homogenized group constants covering the operating and transient conditions over the entire lifetime. Traditionally, the homogenized group constants are generated using lattice physics code over an assembly or block in the case of prismatic high temperature reactors (HTR). For the case of strong absorbers that causes strong local depressions on the flux profile require special techniques during homogenization over a large volume. Fuel blocks with burnable poisons or control rod blocks are example of such cases. Over past several decades, there have been a tremendous number of studies performed for improving the accuracy of full-core calculations through the homogenization procedure. However, those studies were mostly performed for light water reactor (LWR) analyses, thus, may not be directly applicable to advanced thermal reactors such as HTRs. This report presents the application of SuPer-Homogenization correction method to a hypothetical HTR core.

Maternal HtrA3 optimizes placental development to influence offspring birth weight and subsequent white fat gain in adulthood.

Science.gov (United States)

Li, Ying; Salamonsen, Lois A; Hyett, Jonathan; Costa, Fabricio da Silva; Nie, Guiying

2017-07-04

High temperature requirement factor A3 (HtrA3), a member of the HtrA protease family, is highly expressed in the developing placenta, including the maternal decidual cells in both mice and humans. In this study we deleted the HtrA3 gene in the mouse and crossed females carrying zero, one, or two HtrA3-expressing alleles with HtrA3 +/- males to investigate the role of maternal vs fetal HtrA3 in placentation. Although HtrA3 -/- mice were phenotypically normal and fertile, HtrA3 deletion in the mother resulted in intra-uterine growth restriction (IUGR). Disorganization of labyrinthine fetal capillaries was the major placental defect when HtrA3 was absent. The IUGR caused by maternal HtrA3 deletion, albeit being mild, significantly altered offspring growth trajectory long after birth. By 8 months of age, mice born to HtrA3-deficient mothers, independent of their own genotype, were significantly heavier and contained a larger mass of white fat. We further demonstrated that in women serum levels of HtrA3 during early pregnancy were significantly lower in IUGR pregnancies, establishing an association between lower HtrA3 levels and placental insufficiency in the human. This study thus revealed the importance of maternal HtrA3 in optimizing placental development and its long-term impact on the offspring well beyond in utero growth.

Comparative Analysis of Single and Dual Irradiation Pass of Deep Burn High Temperature Reactor Scenario

International Nuclear Information System (INIS)

Jeong, Chang Joon; Jo, Chang Keun; Noh, Jae Man

2012-01-01

A concept of a deep-burn (DB) of trans uranic (TRU) elements in a high temperature reactor (HTR) has been proposed and studied with a single irradiation pass. However, there is still a significant amount of TRU after burn in an HTR. Therefore, it is necessary to burn more TRU in a fast reactor (FR) with repeated reprocessing such as a pyro-process. In this study, the fuel cycle calculations are performed and the results are compared for a singlepass DB-HHR scenario and a dual-pass sodium-cooled fast reactor (SFR) scenario. For the analysis, front-end and back-end parameters are compared. The calculations were performed by the DANESS (Dynamic Analysis of Nuclear Energy System Strategies), which is an integrated system dynamic fuel cycle analysis code

Physics of the pebble-bed high temperature reactor in massive water ingress accidents

International Nuclear Information System (INIS)

Scherer, W.

1989-10-01

A point-kinetics model was developed to describe qualitatively hypothetical water ingress transients in the primary loop of High Temperature Reactors. Neutron kinetics, heat-flow balance and the chemical reaction of graphite corrosion together with their mutual influence are included. The qualitative behaviour of the transients is calculated and discussed for two fictitious examples, namely the long-term water ingress into a medium sized HTR (HTR-500) and the 'startup' of a small HTR after an intensive water flooding of the core. The model developed and the computer code KINKOR are thought to be tools for the general understanding of the water ingress phenomena and should be looked at as basis for more elaborated systems. (orig./HP) [de

Modular high-temperature gas-cooled reactor

International Nuclear Information System (INIS)

Shepherd, L.R.

1988-01-01

The high financial risk involved in building large nuclear power reactors has been a major factor in halting investment in new plant and in bringing further technical development to a standstill. Increased public concern about the safety of nuclear plant, particularly after Chernobyl, has contributed to this stagnation. Financial and technical risk could be reduced considerably by going to small modular units, which would make it possible to build up power station capacity in small steps. Such modular plant, based on the helium-cooled high temperature reactor (HTR), offers remarkable advantages in terms of inherent safety characteristics, partly because of the relatively small size of the individual modules but more on account of the enormous thermal capacity and high temperature margins of the graphitic reactor assemblies. Assessments indicate that, in the USA, the cost of power from the modular systems would be less than that from conventional single reactor plant, up to about 600 MW(e), and only marginally greater above that level, a margin that should be offset by the shorter time required in bringing the modular units on line to earn revenue. The modular HTR would be particularly appropriate in the UK, because of the considerable British industrial background in gas-cooled reactors, and could be a suitable replacement for Magnox. The modular reactor would be particularly suited to combined heat and power schemes and would offer great potential for the eventual development of gas turbine power conversion and the production of high-temperature process heat. (author)

Analysis of diffusion process and influence factors in the air ingress accident of the HTR-PM

Energy Technology Data Exchange (ETDEWEB)

Yanhua, Zheng, E-mail: zhengyh@mail.tsinghua.edu.cn; Fubing, Chen; Lei, Shi

2014-05-01

Air ingress, one of the beyond design basis accidents for high temperature gas-cooled reactors, receives high attention during the design of the 250 MW pebble-bed modular high temperature gas-cooled reactor (HTR-PM), because it may result in severe consequence including the corrosion of the fuel element and graphite reflector. The diffusion process and the set-up time of the stable natural convection after the double-ended guillotine break of the hot-gas duct are studied in the paper. On the basis of the preliminary design of the HTR-PM and its DLOCA analysis results, the diffusion process, as well as the influence of the core temperature distribution and the length of the hot-gas duct, is studied with the DIFFLOW code, which adopts a one-dimension variable cross-section diffusion model with fixed wall temperature. To preliminarily estimate the influence of chemical reaction between oxygen and graphite, which will change the gas component of the mixture, the diffusion processes between the He/N{sub 2}, He/O{sub 2}, He/CO and He/CO{sub 2} are calculated, respectively. Furthermore, the code has been improved and the varying wall temperature can be simulated. The more accurate analysis is carried out with the changing temperature distribution from the DLOCA calculation. The analysis shows that there is enough time to adopt appropriate mitigation measures to stop the air ingress and the severe consequence of fuel element damage and large release of fission product can be avoided.

DNA Methylation Analysis of HTR2A Regulatory Region in Leukocytes of Autistic Subjects.

Science.gov (United States)

Hranilovic, Dubravka; Blazevic, Sofia; Stefulj, Jasminka; Zill, Peter

2016-02-01

Disturbed brain and peripheral serotonin homeostasis is often found in subjects with autism spectrum disorder (ASD). The role of the serotonin receptor 2A (HTR2A) in the regulation of central and peripheral serotonin homeostasis, as well as its altered expression in autistic subjects, have implicated the HTR2A gene as a major candidate for the serotonin disturbance seen in autism. Several studies, yielding so far inconclusive results, have attempted to associate autism with a functional SNP -1438 G/A (rs6311) in the HTR2A promoter region, while possible contribution of epigenetic mechanisms, such as DNA methylation, to HTR2A dysregulation in autism has not yet been investigated. In this study, we compared the mean DNA methylation within the regulatory region of the HTR2A gene between autistic and control subjects. DNA methylation was analysed in peripheral blood leukocytes using bisulfite conversion and sequencing of the HTR2A region containing rs6311 polymorphism. Autistic subjects of rs6311 AG genotype displayed higher mean methylation levels within the analysed region than the corresponding controls (P epigenetic mechanisms might contribute to HTR2A dysregulation observed in individuals with ASD. © 2015 International Society for Autism Research, Wiley Periodicals, Inc.

French activities on gas cooled reactors

International Nuclear Information System (INIS)

Bastien, D.

1996-01-01

The gas cooled reactor programme in France originally consisted of eight Natural Uranium Graphite Gas Cooled Reactors (UNGG). These eight units, which are now permanently shutdown, represented a combined net electrical power of 2,375 MW and a total operational history of 163 years. Studies related to these reactors concern monitoring and dismantling of decommissioned facilities, including the development of methods for dismantling. France has been monitoring the development of HTRs throughout the world since 1979, when it halted its own HTR R and D programme. France actively participates in three CRPs set up by the IAEA. (author). 1 tab

Operating experience with the DRAGON High Temperature Reactor experiment

International Nuclear Information System (INIS)

Simon, R.A.; Capp, P.D.

2002-01-01

The Dragon Reactor Experiment in Winfrith/UK was a materials test facility for a number of HTR projects pursued in the sixties and seventies of the last century. It was built and managed as an OECD/NEA international joint undertaking. The reactor operated successfully between 1964 and 1975 to satisfy the growing demand for irradiation testing of fuels and fuel elements as well as for technological tests of components and materials. The paper describes the reactor's main experimental features and presents results of 11 years of reactor operation relevant for future HTRs. (author)

Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors. Publishable Final Activity Report

International Nuclear Information System (INIS)

Kuijper, J.C.; Somers, J.; Van Den Durpel, L.

2013-01-01

The PUMA project - the acronym stands for “Plutonium and Minor Actinide Management in Thermal High-Temperature Gas-Cooled Reactors” - was a Specific Targeted Research Project (STREP) within the Euratom 6th Framework (EU FP6). The PUMA project ran from September 1, 2006, until August 31, 2009, and was executed by a consortium of 14 European partner organisations and one from the USA. This report serves 2 purposes. It is both the 'Publishable Final Activity Report' and the 'Final (Summary) Report', describing, per Work Package, the specific objectives, research activities, main conclusions, recommendations and supporting documents. PUMA's main objective was to investigate the possibilities for the utilisation and transmutation of plutonium and especially minor actinides in contemporary and future (high temperature) gas-cooled reactor designs, which are promising tools for improving the sustainability of the nuclear fuel cycle. This contributes to the reduction of Pu and MA stockpiles, and also to the development of safe and sustainable reactors for CO2-free energy generation. The PUMA project has assessed the impact of the introduction of Pu/MA-burning HTRs at three levels: fuel and fuel performance (modelling), reactor (transmutation performance and safety) and reactor/fuel cycle facility park. Earlier projects already indicated favourable characteristics of HTRs with respect to Pu burning. So, core physics of Pu/MA fuel cycles for HTRs has been investigated to study the CP fuel and reactor characteristics and to assure nuclear stability of a Pu/MA HTR core, under both normal and abnormal operating conditions. The starting point of this investigation comprised the two main contemporary HTR designs, viz. the pebble-bed type HTR, represented by the South-African PBMR, and hexagonal block type HTR, represented by the GT-MHR. The results (once again) demonstrate the flexibility of the contemporary (and near future) HTR designs and their ability to accept a variety

Materials for advanced high temperature reactors

International Nuclear Information System (INIS)

Graham, L.W.

1977-01-01

Materials are studied in advanced applications of high temperature reactors: helium gas turbine and process heat. Long term creep behavior and corrosion tests are conducted in simulated HTR helium up to 1000 deg C with impurities additions in the furnace atmosphere. Corrosion studies on AISI 321 steels at 800-1000 deg C have shown that the O 2 partial pressure is as low as 10 -24+-3 atm, Ni and Fe cannot be oxidised above about 500 and 600 deg C, Cr cease to oxidise at 800 to 900 deg C and Ti at 900 to 1000 deg C depending on alloy composition γ' strengthened superalloys must depend on a protective corrosion mechanism assisted by the presence of Ti and possibly Cr. Carburisation has been identified metallographically in several high temperature materials: Hastelloy X and M21Z. Alloy TZM appears to be inert in HTR Helium at 900 and 1000 deg C. In alloy 800 and Inconel 625 surface cracks initiation is suppressed but crack propagation is accelerated but this was not apparent in AISI steels, Hastelloy X or fine grain Inconel at 750 deg C

Technology Assessment HTR. Part 7. Social support for the introduction of the High Temperature Reactor

International Nuclear Information System (INIS)

De Ruiter, W.

1996-06-01

The safety of nuclear power plants is the main subject in risk analysis and risk perception of nuclear energy. The question is if a substantial increase in safety according to the classic risk analysis will lead to a decrease in the percepted risks of nuclear energy. In this report the uncertainties in existing risk analysis are dealt with. The results of public risk perception studies of nuclear power are then analysed and possible changes in the public risk perception in the case of the introduction of the HTR is dealt with. Results and conclusions are presented. 4 tabs., 71 refs

The gas-cooled high temperature reactor. Perspectives, problems and programmes

International Nuclear Information System (INIS)

Beckurts, K.H.; Engelmann, P.; Erb, D.E.

1977-01-01

For nearly 20 years extensive research and development programmes on helium-cooled high temperature reactors (HTR) have been carried out in several countries of the world. As a result of the long-standing efforts, satisfactory solutions have been found for many of the basic problems of this new reactor system, particularly in the field of high temperature fuels and materials technology. Three small experimental plants have been operated successfully over extended periods of time. Prototype steam-cycle plants of 300MW(e) are under way at Fort St. Vrain (full-power operation scheduled for 1977) and at Schmehausen (scheduled for 1979). Major delays have occurred in the construction and commissioning of these plants for various reasons but do not reveal specific problems of the HTR. Commercial market introduction of the steam-cycle electricity generating system has been attempted, but the first approach has not been successful. Major efforts both by governments and industry are now required to ensure a successful second approach. To reach competitivity with established nuclear power systems and to take full advantage of the fuel conservation potential of the HTR requires the implementation of the closed thorium fuel cycle on a commercial scale. While some key steps of this cycle have been implemented on a laboratory scale, progress towards a prototype recycling facility has been slow. Closing the thorium fuel cycle represents a major challenge and can only be achieved in a close international collaboration. The paper discusses the world-wide status and potential of HTR technology and reviews the major international development programmes. (author)

New temperature monitoring devices for high-temperature irradiation experiments in the high flux reactor Petten

Energy Technology Data Exchange (ETDEWEB)

Laurie, M.; Futterer, M. A.; Lapetite, J. M. [European Commission Joint Research Centre, Institute for Energy, P.O. Box 2, NL-1755 ZG Petten (Netherlands); Fourrez, S. [THERMOCOAX SAS, BP 26, Planquivon, 61438 Flers Cedex (France); Morice, R. [Laboratoire National de Metrologie et d' Essais, 1 rue Gaston Boissier, 75724 Paris (France)

2009-07-01

Within the European High Temperature Reactor Technology Network (HTR-TN) and related projects a number of HTR fuel irradiations are planned in the High Flux Reactor Petten (HFR), The Netherlands, with the objective to explore the potential of recently produced fuel for even higher temperature and burn-up. Irradiating fuel under defined conditions to extremely high burn-ups will provide a better understanding of fission product release and failure mechanisms if particle failure occurs. After an overview of the irradiation rigs used in the HFR, this paper sums up data collected from previous irradiation tests in terms of thermocouple data. Some research and development work for further improvement of thermocouples and other on-line instrumentation will be outlined. (authors)

Effects of homogeneous geometry models in simulating the fuel balls in HTR-10

International Nuclear Information System (INIS)

Wang Mengjen; Liang Jenqhorng; Peir Jinnjer; Chao Dersheng

2012-01-01

In this study, the core geometry of HTR-10 was simulated using four different models including: (1) model 1 - an explicit double heterogeneous geometry, (2) model 2 - a mixing of UO 2 kernel and four layers in each TRISO particle into one, (3) model 3 - a mixing of 8,335 TRISO particles and the inner graphite matrix in each fuel ball into one, and (4) model 4 - a mixing of the outer graphite shell, 8,335 TRISO particles, and the inner graphite matrix in each fuel ball into one. The associated initial core computations were performed using the MCNP version 1.51 computer code. The experimental fuel loading height of 123 cm was employed for each model. The results revealed that the multiplication factors ranged from largest to smallest with model 1, model 2, model 3, and model 4. The neutron spectrum in the fuel region of each models varied from the hardest to the softest are model 1, model 2, model 3, and model 4 while the averaged neutron spectrum in fuel ball from hardest to softest are model 4, model 3, model 2, and model 1. In addition, the CPU execution times extended from longest to shortest with model 1, model 2, model 3, and model 4. (author)

Mechanical Properties and Structures of Pyrolytic Carbon Coating Layer in HTR Coated Particle Fuel

International Nuclear Information System (INIS)

Lee, Young Woo; Kim, Young Min; Kim, Woong Ki; Cho, Moon Sung

2009-01-01

The TRISO(tri-isotropic)-coated fuel particle for a HTR(High Temperature gas-cooled Reactor) has a diameter of about 1 mm, composed of a nuclear fuel kernel and four different outer coating layers, consisting of a buffer PyC (pyrolytic carbon) layer, inner PyC layer, SiC layer, and outer PyC layer with different coating thicknesses following a specific fuel design. While the fuel kernel is a source for a heat generation by a nuclear fission of fissile uranium, each of the four coating layers acts as a different role in view of retaining the generated fission products and the other interactions during an in-reactor service. Among these coating layers, PyC properties are scarcely in agreement among various investigators and the dependency of their changes upon the deposition condition is comparatively large due to their additional anisotropic properties. Although a recent review work has contributed to an establishment of relationship between the material properties and QC measurements, the data on the mechanical properties and structural parameters of PyC coating layers remain still unclearly evaluated. A review work on dimensional changes of PyC by neutron irradiation was one of re-evaluative works recently attempted by the authors. In this work, an attempt was made to analyze and re-evaluate the existing data of the experimental results of the mechanical properties, i.e., Young's modulus and fracture stress, in relation with the coating conditions, density and the BAF (Bacon Anisotropy Factor), an important structural parameter, of PyC coating layers obtained from various experiments performed in the early periods of the HTR coated particle development

Value-creating investment strategies to manage risk from structural market uncertainties: Switching and compound options in (V)HTR technologies - HTR2008-58157

International Nuclear Information System (INIS)

Lauferts, U.; Halbe, C.; Van Heek, A.

2008-01-01

on the exercise of those that preceded it. At each end of the design phase, the viability will be reviewed conditional on the operating spread at each time step. We quantify the value of being able to wait with the investment into a next block until market conditions are favourable and to be able to abandon one block if market conditions are disapproving. To derive the intrinsic value of this multi block HTR design, it will be compared with a reference investment of a full commitment light water reactor without any managerial flexibility. In another case, we raise the question to what extent product output diversification is a suitable strategy to cope with long term market uncertainty in electricity price. What is the value of a multi-potent technology that is able to produce output for energy markets others than the electricity market? To investigate this, we concentrate on The Netherlands, a country with an intense industrial demand in electricity and hydrogen. (authors)

Numerical simulation of severe water ingress accidents in a modular high temperature gas cooled reactor

International Nuclear Information System (INIS)

Zhang Zuoyi; Scherer, W.

1996-01-01

This report analyzes reverse water ingress accidents in the SIEMENS 200 MW Modular Pebble-Bed High Temperature Gas Cooled Reactor (HTR-MODULE) under the assumption of no active safety protection systems in order to find the safety margins of the current HTR-MODULE design and to realize a catastrophe-free nuclear technology. A water, steam and helium multi-phase cavity model is developed and implemented in the DSNP simulation system. The DSNP system is then used to simulate the primary and secondary circuit of a HTR-MODULE power plant. Comparisons of the model with experiments and with TINTE calculations serve as validation of the simulation. The analysis of the primary circuit tries to answer the question how fast the water enters the reactor core. It was found that the maximum H 2 O concentration increase in the reactor core is smaller than 0.3 kg/(m 3 s). The liquid water vaporization in the steam generator and H 2 O transport from the steam generator to the reactor core reduce the ingress velocity of the H 2 O into the reactor core. In order to answer the question how much water enters the primary circuit, the full cavitation of the feed water pumps is analyzed. It is found that if the secondary circuit is depressurized enough, the feed water pumps will be inherently stopped by the full cavitation. This limits the water to be pumped from the deaerator to the steam generator. A comprehensive simulation of the MODUL-HTR power plant then shows that the H 2 O inventory in the primary circuit can be limited to about 3000 kg. The nuclear reactivity increase caused by the water ingress leads to a fast power excursion, which, however, is inherently counterbalanced by negative feedback effects. Concerning the integrity of the fuel elements, the safety relevant temperature limit of 1600 C was not reached in any case. (orig.) [de

High temperature reactor for the production of low temperature heat

International Nuclear Information System (INIS)

Muehlensiep, J.

1986-12-01

In this report the conditions of nuclear working reactors for district heating are described for the use in suburban areas. The design of a HTR is analysed under the point of view of safety and costs for the components and for the arrangement possibilities. The size of system is chosen by analysing important parameters for construction. The layout is determined by the retention of fission products in the coated particles of the fuel under conditions of hypothetical accidents. Based on stated data a HTR reactor for district heating will be designed. The speciality is a square shaped core which has the advantage to conduct the afterheat fastly to the outside of the pressure vessel in case of hypothetical accidents. Caused by the shape of the core the heat exchangers may be installed next to the core, the shutdown rods are maintained into reflector borings where they have a high efficiency. The whole primary circuit is surrounded by the reactor pressure vessel and is adjusted in an underground concrete cell. (orig./GL) [de

Plutonium and minor actinides management in thermal high - temperature reactors - the EU FP6 project puma

International Nuclear Information System (INIS)

Kuijper, J. C.

2007-01-01

The High Temperature gas-cooled Reactor (HTR) can fulfil a very useful niche for the purposes of Pu and Minor Actinide (MA) incineration due to its unique and unsurpassed safety features, as well as to the attractive incentives offered by the nature of the coated particle (CP) fuel. No European reactor of this type is currently available, but there has been, and still is, considerable interest internationally. Decisions to construct such a reactor in China and in South Africa have already been made or are about to be made. Apart from the unique and unsurpassed safety features offered by this reactor type, the nature of the CP fuel offers a number of attractive characteristics. In particular, it can withstand burn-ups far beyond that in either LWR or FR systems. Demonstrations as high as 75% FIMA have been achieved. The coated particle itself offers significantly improved proliferation resistance, and finally with a correct choice of the kernel composition, it can be a very effective support for direct geological disposal of the fuel. The overall objective of the PUMA project, a Specific Targeted Research Project (STREP) within the European Union 6th Framework (EU FP6), is to investigate the possibilities for the utilisation and transmutation of plutonium and especially minor actinides in contemporary and future (high temperature) gas-cooled reactor designs, which are promising tools for improving the sustainability of the nuclear fuel cycle. This contributes to the reduction of Pu and MA stockpiles, and also to the development of safe and sustainable reactors for CO 2 -free energy generation. A number of important issues concerning the use of Pu and MA in gas-cooled reactors have already been dealt with in other projects, or are being treated in ongoing projects, e.g. as part of EU FP6. However, further steps are required to demonstrate the potential of HTRs as Pu/MA transmuters based on realistic/feasible designs of CP Pu/MA fuel and the PUMA focuses on necessary

The lithium-lithium hydride process for the production of hydrogen: comparison of two concepts for 950 and 1300 deg C HTR helium outlet temperature

International Nuclear Information System (INIS)

Oertel, M.; Weirich, W.; Kuegler, B.; Luecke, L.; Pietsch, M.; Winkelmann, U.

1987-01-01

The lithium-lithium hydride process serves to generate hydrogen from water efficiently, using the high temperature heat of a nuclear reactor. Thermodynamic analyses show that hydrogen can be produced with an overall thermal efficiency of 48% at conventional HTR outlet temperatures of 950 0 C. Assuming helium heat of 1300 0 C, 56% overall thermal efficiency can be achieved. (author)

Status of the HTR programme in France

International Nuclear Information System (INIS)

Ballot, B.; Gauthier, J.C.; Hittner, D.; Lebrun, J.Ph.; Lecomte, M.; Carre, F.; Delbecq, J.M.

2007-01-01

AREVA is convinced that HTR (High Temperature Reactor) is not in competition with large LWRs for electricity generation, and that its actual added value is its potential for addressing cogeneration and industrial process heat production. Therefore AREVA launched in 2004 the ANTARES programme for a pre-conceptual design study, with the support of EDF and together with a large research and development programme needed for the design in close collaboration with Cea. The pre-conceptual phase was finalized end of 2006. The specific feature of AREVA's concept, which distinguishes it from other ones, is its indirect cycle design powering a combined cycle power plant. Several reasons support this design choice, one of the most important being the design flexibility to adapt readily to combined heat and power applications, with a standardised nuclear heat source as independent as possible of the versatile process heat applications with which it is coupled. Standardisation should expedite licensing. In view of the volatility of the costs of fossil fuels, AREVA's choice brings to the large industrial heat applications the fuel cost predictability of nuclear fuel with the efficiency of a high temperature heat source free of greenhouse gases emissions. The reactor module produces 600 MWth which can be split into the required process heat, the remaining power driving an adapted prorated electric plant. Depending on the process heat temperature and power needs, up to 80 % of the nuclear heat is converted into useful energy

A CFD method to evaluate the integrated influence of leakage and bypass flows on the PBMR Reactor Unit

International Nuclear Information System (INIS)

Janse van Rensburg, J.J.; Kleingeld, M.

2010-01-01

Research highlights: → Research and analysis to identify and rank different leakage flow paths in a HTR. → Development of integrated CFD methodology for the prediction of leakage flows. → Development of a methodology to simulate flow resistances in above CFD model. → Validation of predicted flow results against different numerical methodology. → Illustration of the significant improvement achieved through this methodology. - Abstract: An area that has been identified as significantly important in the development of a High Temperature Reactor (HTR) is the prediction of leakage and bypass flows through such a reactor. It is therefore essential to understand the causes of bypass flows and to determine the effect on the predicted fuel and component temperatures. This paper discusses the identification of leakage flows that are applicable to the Pebble Bed Modular Reactor (Pty) Ltd. (PBMR) design and the ranking of these leakage flows. The modeling methodology and results are also discussed. Similar to previous HTR's, it was found that leakage and bypass flows are important parameters to consider for safe and efficient operation of the PBMR. Through a focused approach, it is shown that PBMR is able to improve the understanding of this phenomenon and quantify the flows and subsequent influence on the operation of the system. This has resulted in a reduction of leakage and bypass from approximately 46% to 20%. The improved understanding of leakage and bypass flows allows PBMR to address this issue during the design phase of the project, which subsequently results in a vast improvement over historical HTR designs. This gives PBMR a distinct advantage over previous High Temperature Reactors.

Different contributions of HtrA protease and chaperone activities to Campylobacter jejuni stress tolerance and physiology

DEFF Research Database (Denmark)

Bæk, Kristoffer Torbjørn; Vegge, Christina Skovgaard; Skórko-Glonek, Joanna

2011-01-01

activity is sufficient for growth at high temperature or oxidative stress, whereas the HtrA protease activity is only essential at conditions close to the growth limit for C. jejuni. However, the protease activity was required to prevent induction of the cytoplasmic heat-shock response even at optimal......The microaerophilic bacterium Campylobacter jejuni is the most common cause of bacterial food-borne infections in the developed world. Tolerance to environmental stress relies on proteases and chaperones in the cell envelope such as HtrA and SurA. HtrA displays both chaperone and protease activity......, but little is known about how each of these activities contributes to stress tolerance in bacteria. In vitro experiments showed temperature dependent protease and chaperone activities of C. jejuni HtrA. A C. jejuni mutant lacking only the protease activity of HtrA was used to show that the HtrA chaperone...

HTR combustion head end comparison of the shaft furnace and fluidized bed processes

Energy Technology Data Exchange (ETDEWEB)

Boehnert, R.; Kaiser, G.; Pirk, H.; Tillessen, U.

1975-01-15

Two methods are described for the combustion of the graphite of HTR fuel elements, a sufficient description of the principles being given to permit an understanding of the processes. The present state of the technology of the two processes is then compared on the basis of the results obtained at Gulf General Atomic. Finally, the possibilities of further development are examined using a pilot plant designed to deliver a reactor power of 7000 MWe as the basis. The present report is a collection of facts. It contains neither an evaluation nor a recommendation. A summarized comparison of the state of the technology and the possibilities of development is given in tabular form.

Modelling of fission product release behavior from HTR spherical fuel elements under accident conditions

International Nuclear Information System (INIS)

Verfondern, K.; Mueller, D.

1991-01-01

Computer codes for modelling the fission product release behavior of spherical fuel elements for High Temperature Reactors (HTR) have been developed for the purpose of being used in risk analyses for HTRs. An important part of the validation and verification procedure for these calculation models is the theoretical investigation of accident simulation experiments which have been conducted in the KueFA test facility in the Hot Cells at KFA. The paper gives a presentation of the basic modeling and the calculational results of fission product release from modern German HTR fuel elements in the temperature range 1600-1800 deg. C using the TRISO coated particle failure model PANAMA and the diffusion model FRESCO. Measurements of the transient release behavior for cesium and strontium and of their concentration profiles after heating have provided informations about diffusion data in the important retention barriers of the fuel: silicon carbide and matrix graphite. It could be shown that the diffusion coefficients of both cesium and strontium in silicon carbide can significantly be reduced using a factor in the range of 0.02 - 0.15 compared to older HTR fuel. Also in the development of fuel element graphite, a tendency towards lower diffusion coefficients for both nuclides can be derived. Special heating tests focussing on the fission gases and iodine release from the matrix contamination have been evaluated to derive corresponding effective diffusion data for iodine in fuel element graphite which are more realistic than the iodine transport data used so far. Finally, a prediction of krypton and cesium release from spherical fuel elements under heating conditions will be given for fuel elements which at present are irradiated in the FRJ2, Juelich, and which are intended to be heated at 1600/1800 deg. C in the KueFA furnace in near future. (author). 7 refs, 11 figs

Sustainability and Efficiency Improvements of Gas-Cooled High Temperature Reactors

NARCIS (Netherlands)

Marmier, A.

2012-01-01

The work presented in this thesis covers three fundamental aspects of High Temperature Reactor (HTR) performance, namely fuel testing under irradiation for maximized safety and sustainability, fuel architecture for improved economy and sustainability, and a novel Balance of Plant concept to enable

Frequency and distribution of leakages in steam generators of gas-cooled reactors

International Nuclear Information System (INIS)

Bongratz, R.; Breitbach, G.; Wolters, J.

1988-01-01

In gas cooled reactors with graphitic primary circuit structures - such as HTR, AGR or Magnox - the water ingress is an event of great safety concern. Water or steam entering the primary circuit react with the hot graphite and carbon-oxide and hydrogen are produced. As the most important initiating event a leak in a steam generator must be taken into account. From the safety point of view as well as for availability reasons it is necessary to construct reliable boilers. Thus the occurrence of a boiler leak should be a rare event. In the context of a probabilistic safety study for an HTR-Project much effort was invested to get information about the frequency and the size distribution of tube failures in steam generators of gas cooled reactors. The main data base was the boiler tube failure statistics of United Kingdom gas cooled reactors. The data were selected and applied to a modern HTR steam generator design. A review of the data showed that the failure frequency is not connected with the load level (pressures, temperatures) or with the geometric size of the heating surface of the boiler. Design, construction, fabrication, examination and operation conditions have the greatest influence an the failure frequency but they are practically not to be quantified. The typical leak develops from smallest size. By erosion effects of the entering water or steam it is enlarged to perhaps some mm 2 , then usually it is detected by moisture monitors. Sudden tube breaks were not reported in the investigated period. As a rule boiler leaks in gas cooled reactors are much more, rare then leaks in steam generators of light water reactors and fossil fired boilers. (author)

Inherently safe high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Yamada, Masao; Hayakawa, Hitoshi

1987-01-01

It is recognized in general that High Temperature Gas-cooled Reactors have remarkable characteristics in inherent safety and it is well known that credits of the time margin have been admitted for accident evaluation in the licensing of the currently operating prototype HTGRs (300 MWe class). Recently, more inherently safe HTGRs are being developed in various countries and drawing attention on their possibility for urban siting. The inherent safety characteristics of these HTRs differ each other depending on their design philosophy and on the features of the components/structures which constitute the plant. At first, the specific features/characteristics of the elemental components/structures of the HTRs are explained one by one and then the overall safety features/characteristics of these HTR plants are explained in connection with their design philosophy and combination of the elemental features. Taking the KWU/Interatom Modular Reactor System as an example, the particular design philosophy and safety characteristics of the inherently safe HTR are explained with a result of preliminary evaluation on the possibility of siting close to densely populated area. (author)

EUROPAIRS: The European project on coupling of High Temperature Reactors with industrial processes

International Nuclear Information System (INIS)

Angulo, C.; Bogusch, E.; Bredimas, A.; Delannay, N.; Viala, C.; Ruer, J.; Muguerra, Ph.; Sibaud, E.; Chauvet, V.; Hittner, D.; Fütterer, M.A.; Groot, S. de; Lensa, W. von; Verfondern, K.; Moron, R.; Baudrand, O.; Griffay, G.; Baaten, A.; Segurado-Gimenez, J.

2012-01-01

Developers of High Temperature Reactors (HTR) worldwide acknowledge that the main asset for market breakthrough is its unique ability to address growing needs for industrial cogeneration of heat and power (CHP) owing to its high operating temperature and flexibility, adapted power level, modularity and robust safety features. A strong alliance between nuclear and process heat user industries is a necessity for developing such a nuclear system for the conventional process heat market, just as the electro-nuclear development required a close partnership with utilities. Initiating such an alliance is one of the objectives of the EUROPAIRS project ( (www.europairs.eu)) presently on-going in the frame of the Euratom 7th Framework Programme (FP7). Although small and of short duration (21 months), EUROPAIRS is of strategic importance: it generates the boundary conditions for rapid demonstration of collocating HTR with industrial processes as proposed by the European High Temperature Reactor Technology Network (HTR-TN). This paper presents the main goals, the organization and the working approach of EUROPAIRS. It also presents the status of the viability assessment studies for coupling HTR with industrial end-user systems as one of the main pillars of the project. The main goal of the viability assessment is to identify developments required to remove the last technological and licensing barriers for a viable coupling scheme. The study is expected to result in guidelines for directing the choice of an industrial scale prototype.

EUROPAIRS: The European project on coupling of High Temperature Reactors with industrial processes

Energy Technology Data Exchange (ETDEWEB)

Angulo, C., E-mail: carmen.angulo@gdfsuez.com [Tractebel Engineering S.A. (GDF SUEZ), Avenue Ariane 7, 1200 Brussels (Belgium); Bogusch, E. [AREVA NP GmbH, Paul-Gossen-Strasse 100, 91052 Erlangen (Germany); Bredimas, A. [LGI Consulting, 37 rue de la Grange aux Belles, 75010 Paris (France); Delannay, N. [Tractebel Engineering S.A. (GDF SUEZ), Avenue Ariane 7, 1200 Brussels (Belgium); Viala, C. [AREVA NP SAS, 10 rue Juliette Recamier, 69456 Lyon Cedex 06 (France); Ruer, J.; Muguerra, Ph.; Sibaud, E. [SAIPEM S.A., 1/7 Avenue San Fernando, 78884 Saint Quentin en Yvelines Cedex (France); Chauvet, V. [LGI Consulting, 37 rue de la Grange aux Belles, 75010 Paris (France); Hittner, D. [AREVA NP Inc., 3315 Old Forest Road, Lynchburg, VA 24501 (United States); Fuetterer, M.A. [European Commission, Joint Research Centre, 1755ZG Petten (Netherlands); Groot, S. de [Nuclear Research and Consultancy Group, 1755ZG Petten (Netherlands); Lensa, W. von; Verfondern, K. [Forschungszentrum Juelich GmbH, Leo-Brandt-Strasse,52425 Juelich (Germany); Moron, R. [Solvay SA, rue du Prince Albert 33, 1050 Brussels (Belgium); Baudrand, O. [Institut de Radioprotection et de Surete Nucleaire (IRSN), BP 17, 92262 Fontenay-aux-Roses cedex (France); Griffay, G. [Arcelor Mittal Maizieres Research SA, rue Luigi Cherubini 1A5, 39200 Saint Denis (France); Baaten, A. [USG/Baaten Energy Consulting, Burgermeester-Ceulen-Straat 78, 6212CT Maastricht (Netherlands); Segurado-Gimenez, J. [Tractebel Engineering S.A. (GDF SUEZ), Avenue Ariane 7, 1200 Brussels (Belgium)

2012-10-15

Developers of High Temperature Reactors (HTR) worldwide acknowledge that the main asset for market breakthrough is its unique ability to address growing needs for industrial cogeneration of heat and power (CHP) owing to its high operating temperature and flexibility, adapted power level, modularity and robust safety features. A strong alliance between nuclear and process heat user industries is a necessity for developing such a nuclear system for the conventional process heat market, just as the electro-nuclear development required a close partnership with utilities. Initiating such an alliance is one of the objectives of the EUROPAIRS project ( (www.europairs.eu)) presently on-going in the frame of the Euratom 7th Framework Programme (FP7). Although small and of short duration (21 months), EUROPAIRS is of strategic importance: it generates the boundary conditions for rapid demonstration of collocating HTR with industrial processes as proposed by the European High Temperature Reactor Technology Network (HTR-TN). This paper presents the main goals, the organization and the working approach of EUROPAIRS. It also presents the status of the viability assessment studies for coupling HTR with industrial end-user systems as one of the main pillars of the project. The main goal of the viability assessment is to identify developments required to remove the last technological and licensing barriers for a viable coupling scheme. The study is expected to result in guidelines for directing the choice of an industrial scale prototype.

Identification of E-cadherin signature motifs functioning as cleavage sites for Helicobacter pylori HtrA

Science.gov (United States)

Schmidt, Thomas P.; Perna, Anna M.; Fugmann, Tim; Böhm, Manja; Jan Hiss; Haller, Sarah; Götz, Camilla; Tegtmeyer, Nicole; Hoy, Benjamin; Rau, Tilman T.; Neri, Dario; Backert, Steffen; Schneider, Gisbert; Wessler, Silja

2016-03-01

The cell adhesion protein and tumour suppressor E-cadherin exhibits important functions in the prevention of gastric cancer. As a class-I carcinogen, Helicobacter pylori (H. pylori) has developed a unique strategy to interfere with E-cadherin functions. In previous studies, we have demonstrated that H. pylori secretes the protease high temperature requirement A (HtrA) which cleaves off the E-cadherin ectodomain (NTF) on epithelial cells. This opens cell-to-cell junctions, allowing bacterial transmigration across the polarised epithelium. Here, we investigated the molecular mechanism of the HtrA-E-cadherin interaction and identified E-cadherin cleavage sites for HtrA. Mass-spectrometry-based proteomics and Edman degradation revealed three signature motifs containing the [VITA]-[VITA]-x-x-D-[DN] sequence pattern, which were preferentially cleaved by HtrA. Based on these sites, we developed a substrate-derived peptide inhibitor that selectively bound and inhibited HtrA, thereby blocking transmigration of H. pylori. The discovery of HtrA-targeted signature sites might further explain why we detected a stable 90 kDa NTF fragment during H. pylori infection, but also additional E-cadherin fragments ranging from 105 kDa to 48 kDa in in vitro cleavage experiments. In conclusion, HtrA targets E-cadherin signature sites that are accessible in in vitro reactions, but might be partially masked on epithelial cells through functional homophilic E-cadherin interactions.

Increased expression of Apo-J and Omi/HtrA2 after Intracerebral Hemorrage in rats.

Science.gov (United States)

Li, Feng; Yang, Jing; Guo, Xiaoyan; Zheng, Xiaomei; Lv, Zhiyu; Shi, Chang Qing; Li, Xiaogang

2018-03-23

To investigate the changes of Apo-J and Omi/HtrA2 protein expression in rats with intracerebral hemorrage. 150 SD adult rats were randomly divided into 3 groups: (1) Normal Control (NC) group, (2) Sham group, (3) Intracerebral Hemorrage (ICH) group. The data were collected at 6h, 12h, 1d, 2d, 3d, 5d and 7d. Apoptosis was measured by Tunel staining. The distributions of the Apo-J and Omi/HtrA2 proteins were determined by immunohistochemical staining. The levels of Apo-J mRNA and Omi/HtrA2 mRNA expressions were examined by RT-PCR. Apoptosis in ICH group was higher than Sham and NC groups (p＜0.05). Both the Apo-J and Omi/HtrA2 expression levels were increased in the peripheral region of hemorrhage, with a peak at 3d. The Apo-J mRNA level positively correlated with HtrA2 mRNA level in ICH group (r=0.883, p＜0.001). The expressions of Apo-J and Omi/HtrA2 paralelly increased in peripheral region of rat cerebral hemorrhage. Local high expressed Apo-J in the peripheral regions might play a neuroprotective role by inhibiting apoptosis via Omi/HtrA2 pathway after hemorrhage. Copyright © 2018. Published by Elsevier Inc.

High Temperature Reactors for a new IAEA Coordinated Research Project on energy neutral mineral development processes

Energy Technology Data Exchange (ETDEWEB)

Haneklaus, Nils, E-mail: n.haneklaus@berkeley.edu [Department of Nuclear Engineering, University of California, Berkeley, 4118 Etcheverry Hall, MC 1730, Berkeley, CA 94720-1730 (United States); Reitsma, Frederik [IAEA, Division of Nuclear Power, Section of Nuclear Power Technology Development, VIC, PO Box 100, Vienna 1400 (Austria); Tulsidas, Harikrishnan [IAEA, Division of Nuclear Fuel Cycle and Waste Technology, Section of Nuclear Fuel Cycle and Materials, VIC, PO Box 100, Vienna 1400 (Austria)

2016-09-15

The International Atomic Energy Agency (IAEA) is promoting a new Coordinated Research Project (CRP) to elaborate on the applicability and potential of using High Temperature Reactors (HTRs) to provide process heat and/or electricity to power energy intensive mineral development processes. The CRP aims to provide a platform for cooperation between HTR-developers and mineral development processing experts. Energy intensive mineral development processes with (e.g. phosphate-, gold-, copper-, rare earth ores) or without (e.g. titanium-, aluminum ore) the possibility to recover accompanying uranium and/or thorium that could be developed and used as raw material for nuclear reactor fuel enabling “energy neutral” processing of the primary ore if the recovered uranium and/or thorium is sufficient to operate the greenhouse gas lean energy source used shall be discussed according to the participants needs. This paper specifically focuses on the aspects to be addressed by HTR-designers and developers. First requirements that should be fulfilled by the HTR-designs are highlighted together with the desired outcomes of the research project.

A Critical Review of the Recent Improvements in Minimizing Nuclear Waste by Innovative Gas-Cooled Reactors

Directory of Open Access Journals (Sweden)

E. Bomboni

2008-01-01

Full Text Available This paper presents a critical review of the recent improvements in minimizing nuclear waste in terms of quantities, long-term activities, and radiotoxicities by innovative GCRs, with particular emphasis to the results obtained at the University of Pisa. Regarding these last items, in the frame of some EU projects (GCFR, PUMA, and RAPHAEL, we analyzed symbiotic fuel cycles coupling current LWRs with HTRs, finally closing the cycle by GCFRs. Particularly, we analyzed fertile-free and Pu-Th-based fuel in HTR: we improved plutonium exploitation also by optimizing Pu/Th ratios in the fuel loaded in an HTR. Then, we chose GCFRs to burn residual MA. We have started the calculations on simplified models, but we ended them using more “realistic” models of the reactors. In addition, we have added the GCFR multiple recycling option using keff calculations for all the reactors. As a conclusion, we can state that, coupling HTR with GCFR, the geological disposal issues concerning high-level radiotoxicity of MA can be considerably reduced.

Influence of Polymorphisms in the HTR3A and HTR3B Genes on Experimental Pain and the Effect of the 5-HT3 Antagonist Granisetron.

Science.gov (United States)

Louca Jounger, Sofia; Christidis, Nikolaos; Hedenberg-Magnusson, Britt; List, Thomas; Svensson, Peter; Schalling, Martin; Ernberg, Malin

2016-01-01

The aim of this study was to investigate experimentally if 5-HT3 single nucleotide polymorphisms (SNP) contribute to pain perception and efficacy of the 5-HT3-antagonist granisetron and sex differences. Sixty healthy participants were genotyped regarding HTR3A (rs1062613) and HTR3B (rs1176744). First, pain was induced by bilateral hypertonic saline injections (HS, 5.5%, 0.2 mL) into the masseter muscles. Thirty min later the masseter muscle on one side was pretreated with 0.5 mL granisetron (1 mg/mL) and on the other side with 0.5 mL placebo (isotonic saline) followed by another HS injection (0.2 mL). Pain intensity, pain duration, pain area and pressure pain thresholds (PPTs) were assessed after each injection. HS evoked moderate pain, with higher intensity in the women (P = 0.023), but had no effect on PPTs. None of the SNPs influenced any pain variable in general, but compared to men, the pain area was larger in women carrying the C/C (HTR3A) (P = 0.015) and pain intensity higher in women with the A/C alleles (HTR3B) (P = 0.019). Pre-treatment with granisetron reduced pain intensity, duration and area to a lesser degree in women (P granisetron. Women carrying the C/T & T/T (HTR3A) genotype had less reduction of pain intensity (P = 0.041) and area (P = 0.005), and women with the C/C genotype (HTR3B) had less reduction of pain intensity (P = 0.030), duration (P = 0.030) and area compared to men (P = 0.017). In conclusion, SNPs did not influence experimental muscle pain or the effect of granisetron on pain variables in general, but there were some sex differences in pain variables that seem to be influenced by genotypes. However, due to the small sample size further research is needed before any firm conclusions can be drawn.

Influence of Polymorphisms in the HTR3A and HTR3B Genes on Experimental Pain and the Effect of the 5-HT3 Antagonist Granisetron.

Directory of Open Access Journals (Sweden)

Sofia Louca Jounger

Full Text Available The aim of this study was to investigate experimentally if 5-HT3 single nucleotide polymorphisms (SNP contribute to pain perception and efficacy of the 5-HT3-antagonist granisetron and sex differences. Sixty healthy participants were genotyped regarding HTR3A (rs1062613 and HTR3B (rs1176744. First, pain was induced by bilateral hypertonic saline injections (HS, 5.5%, 0.2 mL into the masseter muscles. Thirty min later the masseter muscle on one side was pretreated with 0.5 mL granisetron (1 mg/mL and on the other side with 0.5 mL placebo (isotonic saline followed by another HS injection (0.2 mL. Pain intensity, pain duration, pain area and pressure pain thresholds (PPTs were assessed after each injection. HS evoked moderate pain, with higher intensity in the women (P = 0.023, but had no effect on PPTs. None of the SNPs influenced any pain variable in general, but compared to men, the pain area was larger in women carrying the C/C (HTR3A (P = 0.015 and pain intensity higher in women with the A/C alleles (HTR3B (P = 0.019. Pre-treatment with granisetron reduced pain intensity, duration and area to a lesser degree in women (P < 0.05, but the SNPs did not in general influence the efficacy of granisetron. Women carrying the C/T & T/T (HTR3A genotype had less reduction of pain intensity (P = 0.041 and area (P = 0.005, and women with the C/C genotype (HTR3B had less reduction of pain intensity (P = 0.030, duration (P = 0.030 and area compared to men (P = 0.017. In conclusion, SNPs did not influence experimental muscle pain or the effect of granisetron on pain variables in general, but there were some sex differences in pain variables that seem to be influenced by genotypes. However, due to the small sample size further research is needed before any firm conclusions can be drawn.

Potential Applications for Nuclear Energy besides Electricity Generation: AREVA Global Perspective of HTR Potential Market

International Nuclear Information System (INIS)

Soutworth, Finis; Gauthier, Jean-Claude; Lecomte, Michel; Carre, Franck

2007-01-01

Energy supply is increasingly showing up as a major issue for electricity supply, transportation, settlement, and process heat industrial supply including hydrogen production. Nuclear power is part of the solution. For electricity supply, as exemplified in Finland and France, the EPR brings an immediate answer; HTR could bring another solution in some specific cases. For other supply, mostly heat, the HTR brings a solution inaccessible to conventional nuclear power plants for very high or even high temperature. As fossil fuels costs increase and efforts to avoid generation of Greenhouse gases are implemented, a market for nuclear generated process heat will develop. Following active developments in the 80's, HTR have been put on the back burner up to 5 years ago. Light water reactors are widely dominating the nuclear production field today. However, interest in the HTR technology was renewed in the past few years. Several commercial projects are actively promoted, most of them aiming at electricity production. ANTARES is today AREVA's response to the cogeneration market. It distinguishes itself from other concepts with its indirect cycle design powering a combined cycle power plant. Several reasons support this design choice, one of the most important of which is the design flexibility to adapt readily to combined heat and power applications. From the start, AREVA made the choice of such flexibility with the belief that the HTR market is not so much in competition with LWR in the sole electricity market but in the specific added value market of cogeneration and process heat. In view of the volatility of the costs of fossil fuels, AREVA's choice brings to the large industrial heat applications the fuel cost predictability of nuclear fuel with the efficiency of a high temperature heat source free of greenhouse gases emissions. The ANTARES module produces 600 MWth which can be split into the required process heat, the remaining power drives an adapted prorated

The prospects of HTGR in China

International Nuclear Information System (INIS)

Sun, Y.; Tong, Y.; Wu, Z.

1994-01-01