Sample records for horizontal rod bundles

  1. CHF prediction in rod bundles using round tube data

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Wallen F.; Veloso, Maria A.F.; Pereira, Cláubia; Costa, Antonella L., E-mail:, E-mail: [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Nuclear


    The present work concerns the use of 1995 CHF table for uniformly heated round tubes, developed jointly by Canadian and Russian researchers, for the prediction of critical heat fluxes in rod bundles geometries. Comparisons between measured and calculated critical heat fluxes indicate that this table could be applied to rod bundles provided that a suitable correction factor is employed. The tolerance limits associated with the departure from nucleate boiling ratio (DNBR) are evaluated by using statistical analysis. (author)

  2. SCADOP: Phenomenological modeling of dryout in nuclear fuel rod bundles

    Energy Technology Data Exchange (ETDEWEB)

    Dasgupta, Arnab, E-mail:; Chandraker, D.K., E-mail:; Vijayan, P.K., E-mail:


    Highlights: • Phenomenological model for annular flow dryout is presented. • The model evaluates initial entrained fraction using a new methodology. • The history effect in annular flow is predicted and validated. • Rod bundle dryout is predicted using subchannel methodology. • Model is validated against experimental dryout data in tubes and rod bundles. - Abstract: Analysis and prediction of dryout is of important consequence to safety of nuclear fuel clusters of boiling water type of reactors. Traditionally, experimental correlations are used for dryout predictions. Since these correlations are based on operating parameters and do not aim to model the underlying phenomena, there has been a proliferation of the correlations, each catering to some specific bundle geometry under a specific set of operating conditions. Moreover, such experiments are extremely costly. In general, changes in tested bundle geometry for improvement in thermal-hydraulic performance would require re-experimentation. Understanding and modeling the basic processes leading to dryout in flow boiling thus has great incentive. Such a model has the ability to predict dryout in any rod bundle geometry, unlike the operating parameter based correlation approach. Thus more informed experiments can be carried out. A good model can, reduce the number of experiments required during the iterations in bundle design. In this paper, a phenomenological model as indicated above is presented. The model incorporates a new methodology to estimate the Initial Entrained Fraction (IEF), i.e., entrained fraction at the onset of annular flow. The incorporation of this new methodology is important since IEF is often assumed ad-hoc and sometimes also used as a parameter to tune the model predictions to experimental data. It is highlighted that IEF may be low under certain conditions against the general perception of a high IEF due to influence of churn flow. It is shown that the same phenomenological model is

  3. Measurement of secondary flow vortices on a rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Vonka, V.


    Secondary flow vortices in infinite rod bundles have been predicted by a number of theoretical analyses. Nevertheless experimental verification was difficult, since the magnitude of the secondary velocities appeared to be less than the accuracy of the experimental techniques used. Only indications of the maximum velocity magnitude have been available but no report on successful direct measurement is known to the author. At ECN, laser Doppler velocimetry is successfully used for measurement of secondary flow vortices in two regular subchannels of a triangularly arranged bare rod bundle with pitch-to-diameter ratio P/D-1.3 under the Reynolds number conditions 60,000 and 175,000. One single secondary vortex, having the average tangential velocity slightly less than 0.1% of the mean bulk velocity, is resolved per minimum symmetry sector of the bundle geometry. Ensemble averages are made to obtain quantitative description of the vortex and to form a data base for comparison with calculations.

  4. New models of droplet deposition and entrainment for prediction of CHF in cylindrical rod bundles

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Haibin, E-mail: [School of Chemical Engineering and Technology, Xi’an Jiaotong University, Xi’an 710049 (China); Department of Chemical Engineering, Imperial College, London SW7 2BY (United Kingdom); Hewitt, G.F. [Department of Chemical Engineering, Imperial College, London SW7 2BY (United Kingdom)


    Highlights: • New models of droplet deposition and entrainment in rod bundles is developed. • A new phenomenological model to predict the CHF in rod bundles is described. • The present model is well able to predict CHF in rod bundles. - Abstract: In this paper, we present a new set of model of droplet deposition and entrainment in cylindrical rod bundles based on the previously proposed model for annuli (effectively a “one-rod” bundle) (2016a). These models make it possible to evaluate the differences of the rates of droplet deposition and entrainment for the respective rods and for the outer tube by taking into account the geometrical characteristics of the rod bundles. Using these models, a phenomenological model to predict the CHF (critical heat flux) for upward annular flow in vertical rod bundles is described. The performance of the model is tested against the experimental data of Becker et al. (1964) for CHF in 3-rod and 7-rod bundles. These data include tests in which only the rods were heated and data for simultaneous uniform and non-uniform heating of the rods and the outer tube. It was shown that the predicted CHFs by the present model agree well with the experimental data and with the experimental observation that dryout occurred first on the outer rods in 7-rod bundles. It is expected that the methodology used will be generally applicable in the prediction of CHF in rod bundles.

  5. Analysis of Subchannel and Rod Bundle PSBT Experiments with CATHARE 3

    Directory of Open Access Journals (Sweden)

    M. Valette


    Full Text Available This paper presents the assessment of CATHARE 3 against PWR subchannel and rod bundle tests of the PSBT benchmark. Noticeable measurements were the following: void fraction in single subchannel and rod bundle, multiple liquid temperatures at subchannel exit in rod bundle, and DNB power and location in rod bundle. All these results were obtained both in steady and transient conditions. Void fraction values are satisfactory predicted by CATHARE 3 in single subchannels with the pipe module. More dispersed predictions of void values are obtained in rod bundles with the CATHARE 3 3D module at subchannel scale. Single-phase liquid mixing tests and DNB tests in rod bundle are also analyzed. After calibrating the mixing in liquid single phase with specific tests, DNB tests using void mixing give mitigated results, perhaps linked to inappropriate use of CHF lookup tables in such rod bundles with many spacers.

  6. Hydrodynamic behavior of a bare rod bundle. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Bartzis, J.G.; Todreas, N.E.


    The temperature distribution within the rod bundle of a nuclear reactor is of major importance in nuclear reactor design. However temperature information presupposes knowledge of the hydrodynamic behavior of the coolant which is the most difficult part of the problem due to complexity of the turbulence phenomena. In the present work a 2-equation turbulence model--a strong candidate for analyzing actual three dimensional turbulent flows--has been used to predict fully developed flow of infinite bare rod bundle of various aspect ratios (P/D). The model has been modified to take into account anisotropic effects of eddy viscosity. Secondary flow calculations have been also performed although the model seems to be too rough to predict the secondary flow correctly. Heat transfer calculations have been performed to confirm the importance of anisotropic viscosity in temperature predictions. All numerical calculations for flow and heat have been performed by two computer codes based on the TEACH code. Experimental measurements of the distribution of axial velocity, turbulent axial velocity, turbulent kinetic energy and radial Reynolds stresses were performed in the developing and fully developed regions. A 2-channel Laser Doppler Anemometer working on the Reference mode with forward scattering was used to perform the measurements in a simulated interior subchannel of a triangular rod array with P/D = 1.124. Comparisons between the analytical results and the results of this experiment as well as other experimental data in rod bundle array available in literature are presented. The predictions are in good agreement with the results for the high Reynolds numbers.

  7. Critical Power in 7-Rod Tight Lattice Bundle (United States)

    Liu, Wei; Kureta, Masatoshi; Akimoto, Hajime

    The Reduced-Moderation Water Reactor (RMWR) has recently becomes of great concern. The RMWR is expected to promote the effective utilization of uranium recourse. The RMWR is based on water-cooled reactor technology, with achieved under lower core water volume and water flow rate. In comparison with the current light water reactors whose water-to-fuel volume ratio is about 2-3, in the RMWR, this value is reduced to less than 0.5. Thereby, there is a need to research its cooling characteristics. Experimental research on critical power in tight lattice bundle that simulates the RMWR has been carried out in Japan Atomic Energy Research Institute (JAERI). The bundle consists one center rod and six peripheral rods. The 7 rods are arranged on a 14.3mm equilateral triangular pitch. Each rod is 13mm in outside diameter. An axial 12-step power distribution is employed to simulate the complicate heating condition in RMWR. Experiments are carried out under G=100-1400kg/m2s, Pex=2-8.5MPa. Effects of mass velocity, inlet temperature, pressure, radial peaking factor and axial peaking factor on critical power and critical quality are discussed. Compared with axial uniform heating condition, the axial non-uniform heating condition causes an obvious decrease in critical quality. Arai correlation, which is the only correlation that has been optimized for tight lattice condition, is verified with the present experimental data. The correlation is found to be able to give reasonable prediction only around RMWR nominal operating condition.

  8. Hierarchical mordenite zeolite nano-rods bundles favourable to bulky molecules (United States)

    Dai, Guang; Hao, Wenming; Xiao, Huan; Ma, Jinghong; Li, Ruifeng


    Hierarchical mordenite zeolite nano-rods bundles were successfully synthesized by a novel approach of using organosilane functioned fumed silica as silicon source. The organic moiety linked on the surface of fumed silica inhibits the growth of zeolite crystal into large size, leading to the nano-rods assembled bundles. The mordenite nanorods bundles exhibited significantly improved mesitylene adsorption capacity compared with the conventional mordenite. As a catalyst, the hierarchical mordenite nanorods bundles showed remarkable catalytic performance in the benzylation of mesitylene by benzyl chloride, due to the efficient diffusion rate and improved accessibility of the active sites in the hierarchical mordenite nanorods bundles.

  9. Turbulent transports by secondary flow vortices in a rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Vonka, V.


    Experimental data on secondary flow vortices in a rod bundle with pitch-to-diameter ratio P/D=1.3 show weak vortices with the average velocity magnitude only about 0.1% of the mean bulk velocity. The question then arises, how important these weak vortices could still be as a transport mechanism in turbulent flows. The transport of axial momentum by these vortices is analysed quantitatively. While a minor importance is observed for the transport in radial direction, it is found that about half of the total transport in circumferential direction is due to the secondary flow vortex convection. Based on the analogy between the transport of momentum and heat, it is expected in nonisothermal situations that, in radial direction, the contribution can improve the heat transfer coefficient and contribute to better economy of heat transfer installations. In circumferential direction, the contribution helps to smooth out circumferential temperature differences, improves the heat removal from heated surfaces and, through a decrease of the maximum surface temperature, it contributes to passive safety of heat transfer installations.

  10. Single- and Two-Phase Turbulent Mixing Rate between Subchannels in Triangle Tight Lattice Rod Bundle

    National Research Council Canada - National Science Library

    KAWAHARA, Akimaro; SADATOMI, Michio; KUDO, Hiroyuki; KANO, Keiko


    In order to obtain the data on turbulent mixing rate between triangle tight lattice subchannels, which will be adopted as the next generation BWR fuel rod bundle, adiabatic experiments were conducted...

  11. Experimental Study on the Flow Characteristics in a Bare Rod Bundle Array

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Seok Kyu; Kim, Bok Deuk; Moon, Sang Ki [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)


    Structure of a rod bundle array in thermal-hydraulic environment is widely used and very important issues in the industrial field. Especially, in nuclear power plant, this structure is essential in the reactor and steam generator. Because of such an industrial importance, there have been many experimental studies on the flow characteristics in a rod bundle array. During two decades from 1970, fundamental studies on the flow mixing in a bare rod bundle have been frequently performed. Rowe et al. measured the axial and some lateral velocities and their turbulence intensities by using 2-D LDV system. They found the existence of the longitudinal macro-scale and the dominant frequency of turbulence in a sub-channel mixing. Neti et al. also performed the LDV measurements for a 3x3 rod array and presented the lateral fluctuations were about 1% magnitudes of the axial flow. Renksizbulut et al. measured the shear stress of the rod surface and estimates the secondary flow in a sub-channel and Vonka also confirmed the secondary flow in his experimental work. In spite of many experimental studies on the flow mixing in a sub-channel geometry on a bare rod bundle, there were no full measurement information in a subchannel. This study attempted to the detailed full measurement of the lateral velocities as well as the axial velocities in a sub-channel geometry on a 5x5 rod bundle.

  12. Enhanced boiling heat transfer in horizontal test bundles

    Energy Technology Data Exchange (ETDEWEB)

    Trewin, R.R.; Jensen, M.K.; Bergles, A.E.


    Two-phase flow boiling from bundles of horizontal tubes with smooth and enhanced surfaces has been investigated. Experiments were conducted in pure refrigerant R-113, pure R-11, and mixtures of R-11 and R-113 of approximately 25, 50, and 75% of R-113 by mass. Tests were conducted in two staggered tube bundles consisting of fifteen rows and five columns laid out in equilateral triangular arrays with pitch-to-diameter ratios of 1.17 and 1.5. The enhanced surfaces tested included a knurled surface (Wolverine`s Turbo-B) and a porous surface (Linde`s High Flux). Pool boiling tests were conducted for each surface so that reference values of the heat transfer coefficient could be obtained. Boiling heat transfer experiments in the tube bundles were conducted at pressures of 2 and 6 bar, heat flux values from 5 to 80 kW/m{sup 2}s, and qualities from 0% to 80%, Values of the heat transfer coefficients for the enhanced surfaces were significantly larger than for the smooth tubes and were comparable to the values obtained in pool boiling. It was found that the performance of the enhanced tubes could be predicted using the pool boiling results. The degradation in the smooth tube heat transfer coefficients obtained in fluid mixtures was found to depend on the difference between the molar concentration in the liquid and vapor.

  13. Computational fluid dynamics (CFD) round robin benchmark for a pressurized water reactor (PWR) rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Shin K., E-mail:; Hassan, Yassin A.


    Highlights: • The capabilities of steady RANS models were directly assessed for full axial scale experiment. • The importance of mesh and conjugate heat transfer was reaffirmed. • The rod inner-surface temperature was directly compared. • The steady RANS calculations showed a limitation in the prediction of circumferential distribution of the rod surface temperature. - Abstract: This study examined the capabilities and limitations of steady Reynolds-Averaged Navier–Stokes (RANS) approach for pressurized water reactor (PWR) rod bundle problems, based on the round robin benchmark of computational fluid dynamics (CFD) codes against the NESTOR experiment for a 5 × 5 rod bundle with typical split-type mixing vane grids (MVGs). The round robin exercise against the high-fidelity, broad-range (covering multi-spans and entire lateral domain) NESTOR experimental data for both the flow field and the rod temperatures enabled us to obtain important insights into CFD prediction and validation for the split-type MVG PWR rod bundle problem. It was found that the steady RANS turbulence models with wall function could reasonably predict two key variables for a rod bundle problem – grid span pressure loss and the rod surface temperature – once mesh (type, resolution, and configuration) was suitable and conjugate heat transfer was properly considered. However, they over-predicted the magnitude of the circumferential variation of the rod surface temperature and could not capture its peak azimuthal locations for a central rod in the wake of the MVG. These discrepancies in the rod surface temperature were probably because the steady RANS approach could not capture unsteady, large-scale cross-flow fluctuations and qualitative cross-flow pattern change due to the laterally confined test section. Based on this benchmarking study, lessons and recommendations about experimental methods as well as CFD methods were also provided for the future research.

  14. Effects of fuel relocation on reflood in a partially-blocked rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Byoung Jae [School of Mechanical Engineering, Chungnam National University, 99 Daehak-ro, Yuseong-gu, Daejeon 34134 (Korea, Republic of); Kim, Jongrok; Kim, Kihwan; Bae, Sung Won [Thermal-Hydraulic Safety Research Division, Korea Atomic Energy Research Division, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of); Moon, Sang-Ki, E-mail: [Thermal-Hydraulic Safety Research Division, Korea Atomic Energy Research Division, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of)


    Ballooning of the fuel rods has been an important issue, since it can influence the coolability of the rod bundle in a large-break loss-of-coolant accident (LBLOCA). Numerous past studies have investigated the effect of blockage geometry on the heat transfer in a partially blocked rod bundle. However, they did not consider the occurrence of fuel relocation and the corresponding effect on two-phase heat transfer. Some fragmented fuel particles located above the ballooned region may drop into the enlarged volume of the balloon. Accordingly, the fuel relocation brings in a local power increase in the ballooned region. The present study’s objective is to investigate the effect of the fuel relocation on the reflood under a LBLOCA condition. Toward this end, experiments were performed in a 5 × 5 partially-blocked rod bundle. Two power profiles were tested: one is a typical cosine shape and the other is the modified shape considering the effect of the fuel relocation. For a typical power shape, the peak temperature in the ballooned rods was lower than that in the intact rods. On the other hand, for the modified power shape, the peak temperature in the ballooned rods was higher than that in the intact rods. Numerical simulations were also performed using the MARS code. The tendencies of the peak clad temperatures were well predicted.

  15. Model for subchannel friction factors and flow redistribution in wire-wrapped rod bundles


    Carajilescov, Pedro; Fernandez y Fernandez, Elói


    The fuel element of LMFBR consists of a bundle of rods wrapped with an helical wire as spacer, surrounded by an hexagonal duct. In the present work, a semi-empirical model is developed to calculate bundle average and subchannel based friction factors and flow redistribution. The obtained results were compared to experimental data and they were considered satisfactory for wide range of geometrical parameters.

  16. Fluid mixing studies in a hexagonal 61-pin, wire-wrapped rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Hanson, A S; Todreas, N


    Two wire-wrapped rod bundles with different leads (6 in. and 12 in.) were constructed with geometric parameters similar to proposed LMFBR fuel assemblies. Rod diameter was 0.25 in. and pitch-to-diameter ratio was 1.26. These two bundles were tested in a flow loop which was designed and built for mixing experiments. Fluid mixing was studied by means of salt tracer dispersion. Salt was injected at various radial and axial locations in the bundle via injection rods, and then the dispersed distribution was measured at the bundle exit by means of 126 specially designed electrical conductivity probes inserted into the bundle subchannels. The data collected showed a strong swirl flow around the bundle circumference and periodic variation with axial injection location. Data from turbulent runs was generally good with mass balances averaging 90% and having a spread of +- 25%. The laminar data collected was generally poor because of a ''striping'' phenomena and injection instabilities. Data were compared with calculations using the ENERGY computer code. The comparison between ENERGY calculations and the data was not good for laminar flow and was only fair in the turbulent cases. It was found that turbulent data could be best characterized by the ENERGY parameters C/sub 1/ = 0.19 and epsilon/sub 1/* = 0.025 when the lead was 6 inches; for a 12-inch lead the parameters were C/sub 1/ = 0.16 and epsilon/sub 1/* = 0.012. Pressure drop data was also taken from the two bundles and it too showed a periodic variation with axial location. Friction factors derived from the data were generally higher than predicted by available correlations. These data suggested that traditional flow split calculations could be in error and that the laminar-turbulent transition occurs over a broad Reynolds number range in wire-wrapped rod bundles.

  17. Hydrodynamic Experiments for a Flow Distribution of a 61-pin Wire-wrapped Rod Bundle

    Energy Technology Data Exchange (ETDEWEB)

    Chang, S. K.; Euh, D. J.; Choi, H. S.; Kim, H. M.; Ko, Y. J.; Lee, D. W.; Lee, H. Y.; Choi, S. R. [KAERI, Daejeon (Korea, Republic of)


    Fuel assembly of the SFR (Sodium-cooled Fast breeder Reactor) type reactor generally has wire spacers which are wrapped around each fuel pin helically in axial direction. The configuration of a helical wire spacer guarantees the fuel rods integrity by providing the bundle rigidity, proper spacing between rods and promoting coolant mixing between subchannels. It is important to understand the flow characteristics in such a triangular array wire wrapped rod bundle in a hexagonal duct. The experimental work has been undertaken to quantify the friction and mixing parameters which characterize the flow distribution in subchannels for the KAERI's own bundle geometric configuration. This work presents the hydrodynamic experimental results for the flow distribution and the pressure drop in subchannels of a 61-pin wire wrapped rod bundle which has been fabricated considering the hydraulic similarity of the reference reactor. Hydrodynamic experiments for a 61-pin wire wrapped test assembly has been performed to provide the data of a flow distribution and pressure losses in subchannels for verifying the analysis capability of subchannel analysis codes for a KAERI's own prototype SFR reactor. Three type of sampling probes have been specially designed to conserve the shape of the flow area for each type of subchannels. All 126 subchannels have been measured to identify the characteristics of the flow distribution in a 37-pin rod assembly. Pressure drops at the interior and the edge subchannels have been also measured to recognize the friction losses of each type of subchannels.

  18. Thermal-hydraulic design of tungsten rod bundles for the APT 3He neutron spallation target (United States)

    Willcutt, Gordon J. E.


    A preconceptual design has been developed for the 3He Target/Blanket System for the Accelerator Production of Tritium Project. The design use tungsten wire-wrapped rods to produce neutrons when the rods are struck by a proton beam. The rods are contained in bundles inside hexagonal Inconel ducts and cooled by D2O. Rod bundles are grouped in patterns in the proton beam inside a chamber filled with 3He that is transmuted to tritium by the neutrons coming from the tungsten rods. Additional 3He is transmuted in a blanket region surrounding the helium chamber. This paper describes the initial thermal-hydraulic design and testing that has been completed to confirm the designed calculations for pressure drop through the bundle and heat transfer in the bundle. Heat transfer tests were run to verify steady-state operation. These tests were followed by increasing power until nucleate boiling occurs to determine operating margins. Changes that improve the initial design are described.

  19. Reflood experiments in rod bundles with flow blockages due to clad ballooning

    Energy Technology Data Exchange (ETDEWEB)

    Moon, S.K.; Kim, J.; Kim, K.; Kim, B.J.; Park, J.K.; Youn, Y.J.; Choi, H.S.; Song, C.H. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    Clad ballooning and the resulting partial flow blockage are one of the major thermal-hydraulic concerns associated with the coolability of partially blocked cores during a loss-of-coolant accident (LOCA). Several in-pile tests have shown that fuel relocation causes a local power accumulation and a high thermal coupling between the clad and fuel debris in the ballooned regions. However, previous experiments in the 1980s did not take into account the fuel relocation phenomena and resulting local power increase in the ballooned regions. The present paper presents the results of systematic investigations on the coolability of rod bundles with flow blockages. The experiments were mainly performed in 5 x 5 rod bundles, 2 x 2 rod bundles and other test facilities. The experiments include a reflood heat transfer, single-phase convective heat transfer, flow redistributions phenomena, and droplet break-up behavior. The effects of the fuel relocation and resulting local power increase were investigated using a 5 x 5 rod bundle. The fuel relocation phenomena increase the peak cladding temperature.

  20. CFD Analysis of Localised Crud Effects on the Flow of Coolant in Nuclear Rod Bundles


    Cinosi, N; Walker, SP


    It has been suggested that crud deposits on a number of adjacent fuel rods might reduce coolant flow rates in associated sub-channels. Such reduced flow rates could then worsen thermal-hydraulic conditions, such as margin to saturated boiling, fuel surface temperature, and the DNB ratio. We report the results of a detailed computational fluid dynamics study of the flow pattern in a partially-crudded rod bundle. Values obviously depend on, for example, the thickness of crud assumed, but sub-ch...

  1. Subchannel analysis and correlation of the Rod Bundle Heat Transfer (RBHT) steam cooling experimental data

    Energy Technology Data Exchange (ETDEWEB)

    Riley, M.P.; Mohanta, L.; Miller, D.J.; Cheung, F.B. [Pennsylvania State Univ., University Park, PA (United States); Bajorek, S.M.; Tien, K.; Hoxie, C.L. [U.S. Nuclear Regulatory Commission, Washington, DC (United States). Office of Nuclear Regulatory Research


    A subchannel analysis of the steam cooling data obtained in the Rod Bundle Heat Transfer (RBHT) test facility has been performed in this study to capture the effect of spacer grids on heat transfer. The RBHT test facility has a 7 x 7 rod bundle with heater rods and with seven spacer grids equally spaced along the length of the rods. A method based on the concept of momentum and heat transport analogy has been developed for calculating the subchannel bulk mean temperature from the measured steam temperatures. Over the range of inlet Reynolds number, the local Nusselt number was found to exhibit a minimum value between the upstream and downstream spacer grids. The presence of a spacer grid not only affects the local Nusselt number downstream of the grid but also affects the local Nusselt number upstream of the next grid. A new correlation capturing the effect of Reynolds number on the local flow restructuring downstream as well as upstream of the spacer grids was proposed for the minimum Nusselt number. In addition, a new enhancement factor accounting for the effects of the upstream as well as downstream spacer grids was developed from the RBHT data. The new enhancement factor was found to compare well with the data from the ACHILLLES test facility.

  2. Evaluation of CHF experimental data for non-square lattice 7-rod bundles

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Dae Hyun; Yoo, Y. J.; Kim, K. K.; Zee, S. Q


    A series of CHF experiments are conducted for 7-rod hexagonal test bundles in order to investigate the CHF characteristics of self-sustained square finned (SSF) rod bundles. The experiments are performed in the freon-loop and water-loop located at IPPE in Russia, and 609 data of freon-12 and 229 data of water are obtained from 7 kinds of test bundles classified by the combination of heated length and axial/radial power distributions. As the result of the evaluation of four representative CHF correlations, the EPRI-1 correlation reveals good prediction capability for SSF test bundles. The inlet parameter CHF correlation suggested by IPPE calculates the mean and the standard deviation of P/M for uniformly heated test bundles as 1.002 and 0.049, respectively. In spite of its excellent accuracy, the correlation has a discontinuity point at the boundary between the low velocity and high velocity conditions. KAERI's inlet parameter correlation eliminates this defect by introducing the complete evaporation model at low velocity condition, and calculates the mean and standard deviation of P/M as 0.095 and 0.062 for uniformly heated 496 data points, respectively. The mean/standard deviation of local parameter CHF correlations suggested by IPPE and KAERI are evaluated as 1.023/0.178 and 1.002/0.158, respectively. The inlet parameter correlation developed from uniformly heated test bundles tends to under-predict CHF about 3% for axially non-uniformly heated test bundles. On the other hand, the local parameter correlation reveals large scattering of P/M, and requires re-optimization of the correlation for non-uniform axial power distributions. As the result of the analysis of experimental data, it reveals that the correction model of axial power shapes suggested by IPPE is applicable to the inlet parameter correlations. For the test bundle of radial non-uniform power distribution, the physically unexpected results are obtained at some experimental conditions. In addition

  3. Determination of the turbulence integral model parameters for a case of a coolant angular flow in regular rod-bundle (United States)

    Bayaskhalanov, M. V.; Vlasov, M. N.; Korsun, A. S.; Merinov, I. G.; Philippov, M. Ph


    Research results of “k-ε” turbulence integral model (TIM) parameters dependence on the angle of a coolant flow in regular smooth cylindrical rod-bundle are presented. TIM is intended for the definition of efficient impulse and heat transport coefficients in the averaged equations of a heat and mass transfer in the regular rod structures in an anisotropic porous media approximation. The TIM equations are received by volume-averaging of the “k-ε” turbulence model equations on periodic cell of rod-bundle. The water flow across rod-bundle under angles from 15 to 75 degrees was simulated by means of an ANSYS CFX code. Dependence of the TIM parameters on flow angle was as a result received.

  4. CFD analysis of localized crud effects on the flow of coolant in nuclear rod bundles

    Energy Technology Data Exchange (ETDEWEB)

    Cinosi, N., E-mail:; Walker, S.P.


    Highlights: • CDF simulation of PWR sub-channels with crudded rods. • Evaluation of coolant flow variations induced by crud rough surfaces. • Evaluation of coolant temperatures in presence of crudded rods. • Evaluation of crud effects on critical heat flux and DNBR margins. - Abstract: It has been suggested that crud deposits on a number of adjacent fuel rods might reduce coolant flow rates in associated sub-channels. Such reduced flow rates could then worsen thermal-hydraulic conditions, such as margin to saturated boiling, fuel surface temperature, and the DNB ratio. We report the results of a detailed computational fluid dynamics study of the flow pattern in a partially crudded rod bundle. Values obviously depend on, for example, the thickness of crud assumed, but sub-channel flow rate reductions of ∼10% were predicted by this analysis. However, this mass flow rate reduction was found to be more than offset by improved heat transfer induced by the relatively rough surface of the crud. Cladding temperatures were predicted to be essentially unchanged, and the DNBR was similarly little altered. We conclude that such flow reduction and diversion is not likely to be of concern.

  5. TREAT Neutronics Analysis of Water-Loop Concept Accommodating LWR 9-rod Bundle

    Energy Technology Data Exchange (ETDEWEB)

    Hill, Connie M.; Woolstenhulme, Nicolas E.; Parry, James R.; Bess, John D.; Housley, Gregory K.


    TREAT fuel elements to facilitate the experiment will not inhibit the ability to successfully simulate a RIA for the 2-pin or 3-pin bundle. This new water loop design leaves room for accommodating a larger fuel pin bundle than previously analyzed. The 7-pin fuel bundle in a hexagonal array with similar spacing of fuel pins in a SFR fuel assembly was considered the minimum needed for one central fuel pin to encounter the most correct thermal conditions. The 9-rod fuel bundle in a square array similar in spacing to pins in a LWR fuel assembly would be considered the LWR equivalent. MCNP analysis conducted on a preliminary LWR 9-rod bundle design shows that sufficient energy deposition into the central pin can be achieved well within range to investigate fuel and cladding performance in a simulated RIA. This is achieved by surrounding the flow channel with an additional annulus of water. Findings also show that a highly significant increase in TREAT to specimen power coupling factor (PCF) within the central pin can be achieved by surrounding the experiment with one to two rings of TREAT upgrade fuel assemblies. The experiment design holds promise for the performance evaluation of PWR fuel at extremely high burnup under similar reactor environment conditions.

  6. Annular flow in rod-bundle: Effect of spacer on disturbance waves

    Energy Technology Data Exchange (ETDEWEB)

    Pham, Son H.; Kunugi, Tomoaki


    A high-speed camera technique is used to study the effect of spacers on the disturbance waves present in annular two-phase flow within a rod-bundle geometry. Images obtained using a backlight configuration to visualize the spacer-wave interactions at the micro-scale resolution (in time and space) are discussed. This paper also presents additional images obtained using a reflected light configuration which provides new observations of the disturbance waves. These images show the separation effect caused by the spacer on the liquid film in which the size of generated liquid droplets can be controlled by the gas superficial velocity. Furthermore, the data confirm that the spacer breaks the circumferential coherent structures of the waves.

  7. Static pressure and wall shear stress distributions in air flow in a seven wire-wrapped rod bundle


    Fernandez y Fernandez, Elói; Carajilescov, Pedro


    An experimental investigation is performed in a turbulent flow in a seven wire-wrapped rod bundle, mounted in an open air facility. Static pressure distributions are measured on central and peripheral rods. By using a Preston tube, the wall shear stress profiles are experimentally obtained along the perimeter of the rods. The geometric parameters of the test section are P/D=1.20 and H/D=15. The measuring section is located at L/D=40 from the air inlet. It is observed that the dimensionless st...

  8. 5 X 5 rod bundle flow field measurements downstream a PWR spacer grid

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Higor F.P.; Silva, Vitor V A.; Santos, André A.C.; Veloso, Maria A.F., E-mail:, E-mail:, E-mail:, E-mail: [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil); Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)


    The spacer grids are structures present in nuclear fuel assembly of Pressurized Water Reactors (PWR). They play an important structural role and also assist in heat removal through the assembly by promoting increased turbulence of the flow. Understanding the flow dynamics downstream the spacer grid is paramount for fuel element design and analysis. This paper presents water flow velocity profiles measurements downstream a spacer grid in a 5 x 5 rod bundle test rig with the objective of highlighting important fluid dynamic behavior near the grid and supplying data for CFD simulation validation. These velocity profiles were obtained at two different heights downstream the spacer grid using a LDV (Laser Doppler Velocimetry) through the top of test rig. The turbulence intensities and patterns of the swirl and cross flow were evaluated. The tests were conducted for Reynolds numbers ranging from 1.8 x 10{sup 4} to 5.4 x 10{sup 4}. This experimental research was carried out in thermo-hydraulics laboratory of Nuclear Technology Development Center – CDTN. Results show great repeatability and low uncertainties (< 1.24 %). Details of the flow field show how the mixture and turbulence induced by the spacer grid quickly decays downstream the spacer grid. It is shown that the developed methodology can supply high resolution low uncertainty results that can be used for validation of CFD simulations. (author)

  9. Receptive field properties of rod-driven horizontal cells in the skate retina (United States)


    The large receptive fields of retinal horizontal cells result primarily from extensive intercellular coupling via gap (electrical) junctions; thus, the extent of the receptive field provides an index of the degree to which the cells are electrically coupled. For rod-driven horizontal cells in the dark-adapted skate retina, a space constant of 1.18 +/- 0.15 mm (SD) was obtained from measurements with a moving slit stimulus, and a comparable value (1.43 +/- 0.55 mm) was obtained with variation in spot diameter. These values, and the extensive spread of a fluorescent dye (Lucifer Yellow) from the site of injection to neighboring cells, indicate that the horizontal cells of the all-rod retina of skate are well coupled electrically. Neither the receptive field properties nor the gap-junctional features of skate horizontal cells were influenced by the adaptive state of the retina: (a) the receptive field organization was unaffected by light adaptation, (b) similar dye coupling was seen in both dark- and light-adapted retinae, and (c) no significant differences were found in the gap-junctional particle densities measured in dark- and light-adapted retinas, i.e., 3,184 +/- 286/microns 2 (n = 8) and 3,073 +/- 494/microns 2 (n = 11), respectively. Moreover, the receptive fields of skate horizontal cells were not altered by either dopamine, glycine, GABA, or the GABAA receptor antagonists bicuculline and picrotoxin. We conclude that the rod-driven horizontal cells of the skate retina are tightly coupled to one another, and that the coupling is not affected by photic and pharmacological conditions that are known to modulate intercellular coupling between cone-driven horizontal cells in other species. PMID:1359000

  10. PWR FLECHT SEASET 163-Rod Bundle Flow Blockage Task data report. NRC/EPRI/Westinghouse report No. 13, August-October 1982

    Energy Technology Data Exchange (ETDEWEB)

    Loftus, M J; Hochreiter, L E; McGuire, M F; Valkovic, M M


    This report presents data from the 163-Rod Bundle Blow Blockage Task of the Full-Length Emergency Cooling Heat Transfer Systems Effects and Separate Effects Test Program (FLECHT SEASET). The task consisted of forced and gravity reflooding tests utilizing electrical heater rods with a cosine axial power profile to simulate PWR nuclear core fuel rod arrays. These tests were designed to determine effects of flow blockage and flow bypass on reflooding behavior and to aid in the assessment of computational models in predicting the reflooding behavior of flow blockage in rod bundle arrays.

  11. Nanofluid Applied Numerical Analysis of Subchannel in Square Rod Bundle for Fusion-Fission Hybrid System

    Energy Technology Data Exchange (ETDEWEB)

    Shamim, Jubair Ahmed; Bhowmik, Palash Kumar; Suh, Kune Y. [Seoul National Univ., Seoul (Korea, Republic of)


    Most of the traditional ways available in the literature to enhance heat transfer are mainly based on variation of structures like addition of heat surface area such as fins, vibration of heated surface, injection or suction of fluids, applying electrical or magnetic fields, and so forth. Application of these mechanical techniques to a fuel rod bundle will involve not only designing complex geometries but also using many additional mechanisms inside a nuclear reactor core which in turn will certainly increase the manufacturing cost as well as may hamper various safety features essential for sound and uninterrupted operation of a nuclear power reactor. On the other hand, traditional heat transfer fluids such as water, ethylene glycol and oils have inherently low thermal conductivity relative to metals and even metal oxides. In this study the coolant with suspended nano-sized particles in the base fluid is proposed as an alternative to increase heat transfer but minimize flow resistance inside a nuclear reactor core. Due to technical complexities most of the previous studies carried out on heat transfer of suspension of metal oxides in fluids were limited to suspensions with millimeter or micron-sized particles. Such outsized particles may lead to severe problems in heat transfer equipment including increased pressure drop and corrosion and erosion of components and pipe lines. Dramatic advancement in modern science has made it possible to produce ultrafine metallic or nonmetallic particles of nanometer dimension, which has brought a revolutionary change in the research of heat transfer enhancement methods. Due to very tiny particle size and their small volume fraction, problems such as clogging and increased pressure drop are insignificant for nanofluids. Moreover, the relatively large surface area of nanoparticles augments the stability of nanofluid solution and prevents the sedimentation of nanoparticles. Xuan and Roetzel considered two approaches to illustrate

  12. CFD modelling of supercritical water flow and heat transfer in a 2 × 2 fuel rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Podila, Krishna, E-mail:; Rao, Yanfei, E-mail:


    Highlights: • Bare and wire wrapped 2 × 2 fuel rod bundles were modelled with CFD. • Sensitivity of predictions to SST k–ω, v{sup 2}–f and turbulent Prandtl number was tested. • CFD predictions were assessed with experimentally reported fuel wall temperatures. - Abstract: In the present assessment of the CFD code, two heat transfer experiments using water at supercritical pressures were selected: a 2 × 2 rod bare bundle; and a 2 × 2 rod wire-wrapped bundle. A systematic 3D CFD study of the fluid flow and heat transfer at supercritical pressures for the rod bundle geometries was performed with the key parameter being the fuel rod wall temperature. The sensitivity of the prediction to the steady RANS turbulence models of SST k–ω, v{sup 2}–f and turbulent Prandtl number (Pr{sub t}) was tested to ensure the reliability of the predicted wall temperature obtained for the current analysis. Using the appropriate turbulence model based on the sensitivity analysis, the mesh refinement, or the grid convergence, was performed for the two geometries. Following the above sensitivity analyses and mesh refinements, the recommended CFD model was then assessed against the measurements from the two experiments. It was found that the CFD model adopted in the current work was able to qualitatively capture the trends reported by the experiments but the degree of temperature rise along the heated length was underpredicted. Moreover, the applicability of turbulence models varied case-by-case and the performance evaluation of the turbulence models was primarily based on its ability to predict the experimentally reported fuel wall temperatures. Of the two turbulence models tested, the SST k–ω was found to be better at capturing the measurements at pseudo-critical and supercritical test conditions, whereas the v{sup 2}–f performed better at sub-critical test conditions. Along with the appropriate turbulence model, CFD results were found to be particularly sensitive to

  13. Measurements of Flow Mixing at Subchannels in a Wire-Wrapped 61-Rod Bundle for a Sodium Cooled Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Won; Kim, Hyungmo; Ko, Yung Joo; Choi, Hae Seob; Euh, Dong-Jin; Jeong, Ji-Young; Lee, Hyeong-Yeon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    For a safety analysis in a core thermal design of a sodium-cooled fast reactor (SFR), flow mixing characteristics at subchannels in a wire-wrapped rod bundle are crucial factor for the design code verification and validation. Wrapped wires make a cross flow in a circumference of the fuel rod, and this effect lets flow be mixed. Therefore the sub-channel analysis method is commonly used for thermal hydraulic analysis of a SFR, a wire wrapped sub-channel type. To measure flow mixing characteristics, a wire mesh sensing technique can be useful method. A wire mesh sensor has been traditionally used to measure the void fraction of a two-phase flow field, i.e. gas and liquid. However, the recent reports that the wire mesh sensor can be used successfully to recognize the flow field in liquid phase by injecting a tracing liquid with a different level of electric conductivity. The subchannel flow characteristics analysis method is commonly used for the thermal hydraulic analysis of a SFR, a wire wrapped subchannel type. In this study, mixing experiments were conducted successfully at a hexagonally arrayed 61-pin wire-wrapped fuel rod bundle test section. Wire mesh sensor was used to measure flow mixing characteristics. The developed post-processing method has its own merits, and flow mixing results were reasonable.

  14. Thermal-Hydraulic Effect of Pattern of Wire-wrap Spacer in 19-pin Rod Bundle for SFR Fuel Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Yeong Shin; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of); Park, Seong Dae [KAERI, Daejeon (Korea, Republic of)


    As sodium-cooled fast reactor (SFR) has been considered the most promising reactor type for future and prototype gen-IV SFR has been developed actively in Korea, thermal-hydraulic aspects of the SFR fuel assembly have the important role for the reactor safety analysis. In PGSFR fuel assembly, 271 pins of fuel rods are tightly packed in triangular array inside hexagonal duct, and wire is wound helically per each fuel rod with regular pattern to assure the gap between rods and prevent the collision, which is called wire-wrapped spacer. Due to helical shape of the wire-wrapped spacer, flow inside duct can have stronger turbulent characteristics and thermal mixing effect. However, many studies showed the possible wake from swirl flow inside subchannel, which cause local hot spot. To prevent the wake flow and improve thermal mixing, new pattern of wire wrap spacer was suggested. To evaluate the effect of wire wrap spacer pattern, CFD analysis was performed for 19-pin rod bundle with comparison of conventional and U-pattern wire wrap spacer. To prevent the wake due to same direction of swirl flow, 7-rod unit pattern of wire spacer, which are arranged to have different rotational direction of wire with adjacent rods and center rod without wire wrap was proposed. From simulation results, swirl flow across gap conflicts its rotation direction causing wake flow from the regular pattern of the conventional one, which generates local hot spot near cladding. With U-pattern of wire wrap spacer, heat transfer in subchannel can be enhanced with evenly distributed cross flow without compensating pressure loss. From the results, the pattern of wire wrap spacer can influence the both heat transfer characteristics and pressure drop, with flow structures generated by wire wrap spacer.

  15. Investigation of combined free and forced convection in a 2 x 6 rod bundle during controlled flow transients

    Energy Technology Data Exchange (ETDEWEB)

    Bates, J.M.; Khan, E.U.


    An experimental study was performed to obtain local fluid velocity and temperature measurements in the mixed (combined free and forced) convection regime for specific flow coastdown transients. A brief investigation of steady-state flows for the purely free-convection regime was also completed. The study was performed using an electrically heated 2 x 6 rod bundle contained in a flow housing. In addition a transient data base was obtained for evaluating the COBRA-WC thermal-hydraulic computer program (a modified version of the COBRA-IV code).

  16. Measurement of Flow Distribution at Subchannels in a Wire-Wrapped 37-Rod Bundle for a Sodium Cooled Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, HYungmo; Chang, Seokkyu; Lee, Dong Won; Choi, Hae Seob; Euh, Dongjin; Lee, Hyeongyeon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    In this SFR type of fuel rod, core subchannels are classified with interior, edge, and corner subchannels. Flow distribution of each subchannel is a crucial factor for the core thermal design, and experimental tests for the design code verification and validation in a temperature limitation analysis were conducted. To verify and validate computer codes for the SFR core thermal design, a hexagonally arrayed 37-pin wire-wrapped fuel rod bundle test section was fabricated. The measurement experiments were conducted using a well- designed test loop and iso-kinetic sampling probe. The developed iso-kinetic sampling method in the present study has its own merits, and flow rate results by sampling showed in good agreement with the preliminary CFD analysis results. In addition, the estimated mass balance error was only about 3% in the experiments. Therefore, the present methodology and results can be used in future experiments for design code verification and validation.

  17. Research of heat transfer of staggered horizontal bundles of finned tubes at free air convection (United States)

    Novozhilova, A. V.; Maryna, Z. G.; Samorodov, A. V.; Lvov, E. A.


    The study of free-convective processes is important because of the cooling problem in many machines and systems, where other ways of cooling are impossible or impractical. Natural convective processes are common in the steam turbine air condensers of electric power plants located within the city limits, in dry cooling towers of circulating water systems, in condensers cooled by air and water, in radiators cooling oil of power electric transformers, in emergency cooling systems of nuclear reactors, in solar power, as well as in air-cooling of power semiconductor energy converters. All this makes actual the synthesis of the results of theoretical and experimental research of free convection for heat exchangers with finned tube bundles. The results of the study of free-convection heat transfer for two-, three- and four-row staggered horizontal bundles of industrial bimetallic finned tubes with finning factor of 16.8 and equilateral tubes arrangement are presented. Cross and diagonal steps in the bundles are the same: 58; 61; 64; 70; 76; 86; 100 mm, which corresponds to the relative steps: 1.042; 1.096; 1.152; 1.258; 1.366; 1.545; 1.797. These steps are standardized for air coolers. An equation for calculating the free-convection heat transfer, taking into account the influence of geometrical parameters in the range of Rayleigh number from 30,000 to 350,000 with an average deviation of ± 4.8%, has been obtained. The relationship presented in the article allows designing a wide range of air coolers for various applications, working in the free convection modes.

  18. Measurements of Flow Mixing at Subchannels in a Wire-Wrapped 37-Rod Bundle for a Sodium Cooled Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyungmo; Bae, Hwang; Chang, Seok-Kyu; Choi, Sun Rock; Lee, Dong Won; Ko, Yung Joo; Choi, Hae Seob; Euh, Dong-Jin; Lee, Hyeong-Yeon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    For a safety analysis in a core thermal design of a sodium-cooled fast reactor (SFR), flow mixing characteristics at subchannels in a wire-wrapped rod bundle are very important. Wrapped wires make a cross flow in a around the fuel rod) of the fuel rod, and this effect lets flow be mixed. Experimental results of flow mixing can be meaningful for verification and validation of thermal mixing correlation in a reactor core thermo-hydraulic design code. A wire mesh sensing technique can be useful method for measuring of flow mixing characteristics. A wire mesh sensor has been traditionally used to measure the void fraction of a two-phase flow field, i.e. gas and liquid. However, it has been recently reported that the wire mesh sensor can be used successfully to recognize the flow field in liquid phase by injecting a tracing liquid with a different level of electric conductivity. This can be powerfully adapted to recognize flow mixing characteristics by wrapped wires in SFR core thermal design. In this work, we conducted the flow mixing experiments using a custom designed wire mesh sensor. To verify and validate computer codes for the SFR core thermal design, mixing experiments were conducted at a hexagonally arrayed 37-pin wire-wrapped fuel rod bundle test section. The well-designed wire mesh sensor was used to measure flow mixing characteristics. The developed post-processing method has its own merits, and flow mixing results were reasonable. In addition, by uncertainty analysis, the system errors and the random error were estimated in experiments. Therefore, the present results and methods can be used for design code verification and validation.

  19. Coolant mixing in LMFBR rod bundles and outlet plenum mixing transients (United States)

    Todreas, N. E.; Cheng, S. K.; Basehore, K.


    The thermal hydraulic performance of wire wrapped fuel bundles of LMFBR configuration was investigated. Results obtained included phenomenological models for friction factors, flow split and mixing characteristics; correlations for predicting these characteristics suitable for insertion in design codes; numerical codes for analyzing bundle behavior both of the lumped subchannel and distributed parameter categories and experimental techniques for pressure velocity, flow split, salt conductivity and temperature measurement in water cooled mockups of bundles and subchannels. Flow regimes investigated included laminar, transition and turbulent flow under forced convection and mixed convection conditions. Forced convections conditions are emphasized. Outlet plenum behavior is also investigated.

  20. Effects of axial power shapes on CHF locations in a single tube and in rod bundle assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Han, B.; Yang, B.W.; Zhang, H.; Zha, Y.; Zhang, Y. [Xi' an Jiaotong Univ. (China). School of Nuclear Science and Technology


    Currently, the prediction of rod bundle CHF is dependent on CHF correlations derived from CHF data. A simple correction factor, such as F-factor, is often used to account for the axial power shape differences based on a simple accumulated energy concept, which has totally no consideration on the impact of true local condition on CHF mechanism. Subsequently, as expected, large uncertainty is often associated with the CHF value and CHF location predictions. For the purpose of obtaining different power shapes effects on CHF, CFD calculated parameter values were used to predict the possible CHF occurrence location. The possible CHF location prediction method proposed in this paper is calculated void fraction, heat transfer coefficient (HTC), liquid temperature distribution and detailed local parameters. And the uniform and non-uniform CHF were analyzed. The prediction of possible CHF locations in a 5 x 5 rod bundle may provide useful information for the design of a full-length CHF test, enhance the accuracy of CHF and CHF location prediction, and reduce the costs of the experimentation.

  1. Subchannel Scale Thermal-Hydraulic Analysis of Rod Bundle Geometry under Single-phase Adiabatic Conditions Using CUPID

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Seok Jong; Park, Goon Cherl; Cho, Hyoung Kyu [KAERI, Daejeon (Korea, Republic of)


    In Korea, subchannel analysis code, MATRA has been developed by KAERI (Korea Atomic Energy Research Institute). MATRA has been used for reactor core T/H design and DNBR (Departure from Nucleate Boiling Ratio) calculation. Also, the code has been successfully coupled with neutronics code and fuel analysis code. However, since major concern of the code is not the accident simulation, some features of the code are not optimized for the accident conditions, such as the homogeneous model for two-phase flow and spatial marching method for numerical scheme. For this reason, in the present study, application of CUPID for the subchannel scale T/H analysis in rod bundle geometry was conducted. CUPID is a component scale T/H analysis code which adopts three dimensional two-fluid three-field model developed by KAERI. In this paper, the validation results of the CUPID code for subchannel scale rod bundle analysis at single phase adiabatic conditions were presented. At first, the physical models required for a subchannel scale analysis were implemented to CUPID. In the future, the scope of validation tests will be extended to diabetic and two phase flow conditions and required models will be implemented into CUPID.

  2. Turbulence Model Evaluation Study for a Secondary Flow and a Flow Pulsation in the Sub-Channels of an 18-Finned Rod Bundle by Using Computational Fluid Dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jong Hark; Chae, Hee Taek; Park, Cheol; Kim, Heon Il


    Since the heat flux of the rod type fuel used in the HANARO, a research reactor being operated in the KAERI, is substantially higher than the heat flux of power reactors, the HANARO fuel has 8 longitudinal fins for enhancing the heat release from the fuel rod surface. This unique shape of a nuclear fuel led us to study the flows and thermal hydraulic characteristics of it. Especially because the flows through the narrow channels built up by these finned rod fuels would be different from the flow characteristics in the coolant channels formed by bare rod fuels, some experimental studies to investigate the flow behaviors and structures in a finned rod bundle were done by other researchers. But because of the very complex geometries of the flow channels in the finned rod bundle only allowed us to obtain limited information about the flow characteristics, a numerical study by a computational fluid dynamics technique has been adopted to elucidate more about such a complicated flow in a finned rod bundle. In this study, for the development of an adequate computational model to simulate such a complex geometry, a mesh sensitivity study and the effects of various turbulence models were examined. The CFD analysis results were compared with the experimental results. Some of them have a good agreement with the experimental results. All linear eddy viscosity turbulence models could hardly predict the secondary flows near the fuel surfaces and in the sub-channel, but the RSM (Reynolds Stress Model) revealed very different results from the eddy viscosity turbulence models. In the transient analysis all turbulence model predicted flow pulsation at the center of a subchannel as well as at the gap between rods in spite of large P/D. The flow pulsation showed different results with turbulence models and the location in the sub-channels.

  3. CFD analysis of pressure drop across grid spacers in rod bundles compared to correlations and heavy liquid metal experimental data

    Energy Technology Data Exchange (ETDEWEB)

    Batta, A., E-mail:; Class, A.G., E-mail:


    Early studies of the flow in rod bundles with spacer grids suggest that the pressure drop can be decomposed in contributions due to flow area variations by spacer grids and frictional losses along the rods. For these shape and frictional losses simple correlations based on theoretical and experimental data have been proposed. In the OECD benchmark study LACANES it was observed that correlations could well describe the flow behavior of the heavy liquid metal loop including a rod bundle with the exception of the core region, where different experts chose different pressure-loss correlations for the losses due to spacer grids. Here, RANS–CFD simulations provided very good data compared to the experimental data. It was observed that the most commonly applied Rehme correlation underestimated the shape losses. The available correlations relate the pressure drop across a grid spacer to the relative plugging of the spacer i.e. solidity e{sub max}. More sophisticated correlations distinct between spacer grids with round or sharp leading edge shape. The purpose of this study is to (i) show that CFD is suitable to predict pressure drop across spacer grids and (ii) to access the generality of pressure drop correlations. By verification and validation of CFD results against experimental data obtained in KALLA we show (i). The generality (ii) is challenged by considering three cases which yield identical pressure drop in the correlations. First we test the effect of surface roughness, a parameter not present in the correlations. Here we compare a simulation assuming a typical surface roughness representing the experimental situation to a perfectly smooth spacer surface. Second we reverse the flow direction for the spacer grid employed in the experiments which is asymmetric. The flow direction reversal is chosen for convenience, since an asymmetric spacer grid with given blockage ratio, may result in different flow situations depending on flow direction. Obviously blockage

  4. Characteristics of copper-clad aluminum rods prepared by horizontal continuous casting (United States)

    Zhang, Yubo; Fu, Ying; Jie, Jinchuan; Wu, Li; Svynarenko, Kateryna; Guo, Qingtao; Li, Tingju; Wang, Tongmin


    An innovative horizontal continuous casting method was developed and successfully used to prepare copper-clad aluminum (CCA) rods with a diameter of 85 mm and a sheath thickness of 16 mm. The solidification structure and element distribution near the interface of the CCA ingots were investigated by means of a scanning electron microscope, an energy dispersive spectrometer, and an electron probe X-ray microanalyzer. The results showed that the proposed process can lead to a good metallurgical bond between Cu and Al. The interface between Cu and Al was a multilayered structure with a thickness of 200 μm, consisting of Cu9Al4, CuAl2, α-Al/CuAl2 eutectic, and α-Al + α-Al/CuAl2 eutectic layers from the Cu side to the Al side. The mean tensile-shear strength of the CCA sample was 45 MPa, which fulfills the requirements for the further extrusion process. The bonding and diffusion mechanisms are also discussed in this paper.

  5. Fluid dynamics and heat transfer within rod bundles at supercritical pressure

    Energy Technology Data Exchange (ETDEWEB)

    Laurien, E. [Stuttgart Univ. (DE). Inst. for Nuclear Technology and Energy Systems (IKE)


    Due to the present absence of experimental investigations of HPLWR flows, the flow and heat transfer of the fuel bundle is investigated only theoretically at 25 MPa. Here, the tool of CFD is used primarily to model the coupled effects of heat transfer deterioration, secondary flows, inter-channel mixing and swirl in order to understand the associated flow and heat transfer phenomena. The aim is the development of a heat transfer correlation for the HPLWR fuel element to be used in sub-channel codes. In further studies the fuel element must be optimized in order to guarantee, that the cladding temperature will not exceed the material limit of about 620 C even if moderate deterioration occurs. Further challenges for the design and the flow simulation methods will be the turbulent mixing of streams at 25 MPa with large temperature differences in the hot box, the lower plenum, and the foot piece of the fuel elements, see [12] for a preliminary study. (orig.)

  6. GMDH-type neural network modeling and genetic algorithm-based multi-objective optimization of thermal and friction characteristics in heat exchanger tubes with wire-rod bundles (United States)

    Rahimi, Masoud; Beigzadeh, Reza; Parvizi, Mehdi; Eiamsa-ard, Smith


    The group method of data handling (GMDH) technique was used to predict heat transfer and friction characteristics in heat exchanger tubes equipped with wire-rod bundles. Nusselt number and friction factor were determined as functions of wire-rod bundle geometric parameters and Reynolds number. The performance of the developed GMDH-type neural networks was found to be superior in comparison with the proposed empirical correlations. For optimization, the genetic algorithm-based multi-objective optimization was applied.

  7. An experimental investigation of supercritical heat transfer in a three-rod bundle equipped with wire-wrap and grid spacers and cooled by carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Eter, Ahmad, E-mail:; Groeneveld, Dé, E-mail:; Tavoularis, Stavros, E-mail:


    Highlights: • Heat transfer at supercritical pressures was studied experimentally in a three-rod bundle equipped with wire-wrap spacers or grid spacers. • Heat transfer deterioration occurred near the heated inlet under certain conditions. • Normal heat transfer was generally comparable to that in a tube and the predictions of a correlation. - Abstract: Heat transfer measurements in a three-rod bundle equipped with wire-wrap and grid spacers were obtained at supercritical pressures in the Supercritical University of Ottawa Loop (SCUOL). The tests were performed using carbon dioxide, as a surrogate fluid for water, flowing upwards for wide ranges of conditions, including conditions equivalent to the nominal and near-normal operating conditions of the proposed Canadian Super-Critical Water-Cooled Reactor. The test section contained three heated rods and three unheated rod segments with an outer diameter of 10 mm and a pitch-to-diameter ratio of 1.14; the heated length was 1500 mm. Detailed surface temperature measurements along and around the three heated rods were collected using internally traversed thermocouples. The following ranges of test conditions were covered, with equivalent water conditions given inside parentheses: pressure from 6.6 to 8.36 MPa (19.7–25 MPa); inlet temperature from 11 to 30 °C (330–371 °C); mass flux from 200 to 1175 kg m{sup −2} s{sup −1} (340–1822 kg m{sup −2} s{sup −1}); and wall heat flux from 1 to 175 kW m{sup −2} (11–1847 kW m{sup −2}). For one set of tests, the heated rods were fitted with a 1.3 mm OD wire wrap, having an axial pitch of 200 mm along the entire heated length; for a second set, the heated rods were fitted with grid spacers having a 5.3% flow blockage and located at 500 mm axial intervals. The effects of spacer configuration on heat transfer at supercritical pressures were documented and analyzed. The observed experimental trends were compared to those obtained in a experiment in a heated

  8. Fuel cell integral bundle assembly including ceramic open end seal and vertical and horizontal thermal expansion control (United States)

    Zafred, Paolo R [Murrysville, PA; Gillett, James E [Greensburg, PA


    A plurality of integral bundle assemblies contain a top portion with an inlet fuel plenum and a bottom portion containing a base support, the base supports a dense, ceramic air exhaust manifold having four supporting legs, the manifold is below and connects to air feed tubes located in a recuperator zone, the air feed tubes passing into the center of inverted, tubular, elongated, hollow electrically connected solid oxide fuel cells having an open end above a combustion zone into which the air feed tubes pass and a closed end near the inlet fuel plenum, where the open end of the fuel cells rest upon and within a separate combination ceramic seal and bundle support contained in a ceramic support casting, where at least one flexible cushion ceramic band seal located between the recuperator and fuel cells protects and controls horizontal thermal expansion, and where the fuel cells operate in the fuel cell mode and where the base support and bottom ceramic air exhaust manifolds carry from 85% to all of the weight of the generator.

  9. A Secondary Flow Effect on the Heat and Mass Transfer Processes in the Finned Rod Bundles of Gas-cooled Reactors

    Directory of Open Access Journals (Sweden)

    A. A. Dunaitsev


    Full Text Available In nuclear power engineering a need to justify an operability of products and their components is of great importance. In high-temperature gas reactors, the critical element affecting the facility reliability is the fuel rod cladding, which in turn leads to the need to gain knowledge in the field of gas dynamics and heat transfer in the reactor core and to increase the detail of the calculation results. For the time being, calculations of reactor core are performed using the proven techniques of per-channel calculations, which show good representativeness and count rate. However, these techniques require additional experimental studies to describe correctly the inter-channel exchange, which, being taken into account, largely affects the pattern of the temperature fields in the region under consideration. Increasingly more relevant and demandable are numerical simulation methods of fluid and gas dynamics, as well as of heat exchange, which consist in the direct solution of the system of differential equations of mass balance, kinetic moment, and energy. Calculation of reactor cores or rod bundles according these techniques does not require additional experimental studies and allows us to obtain the local distributions of flow characteristics in the bundle and the flow characteristics that are hard to measure in the physical experiment.The article shows the calculation results and their analysis for an infinite rod lattice of the reactor core. The results were obtained by the technique of modelling one rod of a regular lattice using the periodic boundary conditions, followed by translating the results to the neighbouring rods. In channels of complex shape, there are secondary flows caused by changes in the channel geometry along the flow and directed across the main front of the flow. These secondary flows in the reactor cores with rods spaced by the winding wire lead to a redistribution of the coolant along the channel section, which in turn

  10. Flow Distribution and Pressure Loss in Subchannels of a Wire-Wrapped 37-pin Rod Bundle for a Sodium-Cooled Fast Reactor


    Chang, Seok-Kyu; Euh, Dong-Jin; Choi, Hae Seob; Kim, Hyungmo; Choi, Sun Rock; Lee, Hyeong-Yeon


    A hexagonally arrayed 37-pin wire-wrapped rod bundle has been chosen to provide the experimental data of the pressure loss and flow rate in subchannels for validating subchannel analysis codes for the sodium-cooled fast reactor core thermal/hydraulic design. The iso-kinetic sampling method has been adopted to measure the flow rate at subchannels, and newly designed sampling probes which preserve the flow area of subchannels have been devised. Experimental tests have been performed at 20–115% ...

  11. COBRA-IV-I: an interim version of COBRA for thermal-hydraulic analysis of rod bundle nuclear fuel elements and cores

    Energy Technology Data Exchange (ETDEWEB)

    Wheeler, C.L.; Stewart, C.W.; Cena, R.J.; Rowe, D.S.; Sutey, A.M.


    The COBRA-IV-I computer code uses the subchannel analysis approach to determine the enthalpy and flow distribution in rod bundles for both steady-state and transient conditions. The steady-state and transient solution schemes used in COBRA-IIIC are still available in COBRA-IV-I as the implicit solution scheme option. In addition to these techniques, a new explicit solution scheme is now available which allows the calculation of severe transients involving flow reversals, recirculations, expulsion and reentry flows, with a pressure or flow boundary condition specified. Significant storage compaction and reduced running times have been achieved to allow the calculation of problems involving hundreds of subchannels.

  12. Experimental Research on Water Boiling Heat Transfer on Horizontal Copper Rod Surface at Sub-Atmospheric Pressure

    Directory of Open Access Journals (Sweden)

    Li-Hua Yu


    Full Text Available In recent years, water (R718 as a kind of natural refrigerant—which is environmentally-friendly, safe and cheap—has been reconsidered by scholars. The systems of using water as the refrigerant, such as water vapor compression refrigeration and heat pump systems run at sub-atmospheric pressure. So, the research on water boiling heat transfer at sub-atmospheric pressure has been an important issue. There are many research papers on the evaporation of water, but there is a lack of data on the characteristics at sub-atmospheric pressures, especially lower than 3 kPa (the saturation temperature is 24 °C. In this paper, the experimental research on water boiling heat transfer on a horizontal copper rod surface at 1.8–3.3 kPa is presented. Regression equations of the boiling heat transfer coefficient are obtained based on the experimental data, which are convenient for practical application.

  13. Flow distribution and pressure loss in subchannels of a wire-wrapped 37-pin rod bundle for sodium-cooled fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Seok Kyu; Euh, Dong Jin; Choi, Hae Seob; Kim, Hyung Mo; Choi, Sun Rock; Lee, Hyeong Yeon [Thermal-Hydraulic Safety Research Department, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    A hexagonally arrayed 37-pin wire-wrapped rod bundle has been chosen to provide the experimental data of the pressure loss and flow rate in subchannels for validating subchannel analysis codes for the sodium-cooled fast reactor core thermal/hydraulic design. The iso-kinetic sampling method has been adopted to measure the flow rate at subchannels, and newly designed sampling probes which preserve the flow area of subchannels have been devised. Experimental tests have been performed at 20-115% of the nominal flow rate and 60 degrees C (equivalent to Re ∼ 37,100) at the inlet of the test rig. The pressure loss data in three measured subchannels were almost identical regardless of the subchannel locations. The flow rate at each type of subchannel was identified and the flow split factors were evaluated from the measured data. The predicted correlations and the computational fluid dynamics results agreed reasonably with the experimental data.

  14. A genetic algorithm-based optimization model for pool boiling heat transfer on horizontal rod heaters at isolated bubble regime (United States)

    Alavi Fazel, S. Ali


    A new optimized model which can predict the heat transfer in the nucleate boiling at isolated bubble regime is proposed for pool boiling on a horizontal rod heater. This model is developed based on the results of direct observations of the physical boiling phenomena. Boiling heat flux, wall temperature, bubble departing diameter, bubble generation frequency and bubble nucleation site density have been experimentally measured. Water and ethanol have been used as two different boiling fluids. Heating surface was made by several metals and various degrees of roughness. The mentioned model considers various mechanisms such as latent heat transfer due to micro-layer evaporation, transient conduction due to thermal boundary layer reformation, natural convection, heat transfer due to the sliding bubbles and bubble super-heating. The fractional contributions of individual mentioned heat transfer mechanisms have been calculated by genetic algorithm. The results show that at wall temperature difference more that about 3 K, bubble sliding transient conduction, non-sliding transient conduction, micro-layer evaporation, natural convection, radial forced convection and bubble super-heating have higher to lower fractional contributions respectively. The performance of the new optimized model has been verified by comparison of the existing experimental data.

  15. Flow Distribution and Pressure Loss in Subchannels of a Wire-Wrapped 37-pin Rod Bundle for a Sodium-Cooled Fast Reactor

    Directory of Open Access Journals (Sweden)

    Seok-Kyu Chang


    Full Text Available A hexagonally arrayed 37-pin wire-wrapped rod bundle has been chosen to provide the experimental data of the pressure loss and flow rate in subchannels for validating subchannel analysis codes for the sodium-cooled fast reactor core thermal/hydraulic design. The iso-kinetic sampling method has been adopted to measure the flow rate at subchannels, and newly designed sampling probes which preserve the flow area of subchannels have been devised. Experimental tests have been performed at 20–115% of the nominal flow rate and 60°C (equivalent to Re ∼ 37,100 at the inlet of the test rig. The pressure loss data in three measured subchannels were almost identical regardless of the subchannel locations. The flow rate at each type of subchannel was identified and the flow split factors were evaluated from the measured data. The predicted correlations and the computational fluid dynamics results agreed reasonably with the experimental data.

  16. Experimental study on the low flow CHF in vertical 3x3 rod bundle with non-uniform axial heat flux distribution

    Energy Technology Data Exchange (ETDEWEB)

    Moon, Sang Ki; Cho, Seok; Chun, Se Young; Park, Jong Kuk; Kim, Bok Deuk; Youn, Young Jung; Baek, Won Pil


    An experimental study of the Critical Heat Flux (CHF) has been performed for a water flow in a non-uniformly heated vertical 3x3 rod bundle under low flow and a wide range of pressure conditions. Since most of experimental studies on the low flow CHF have been performed under low pressure conditions, present study has investigated the effects of various parameters on the CHF under low flow and a wide range of pressure conditions. Especially, these experiments are focused on the CHF under Return-To-Power (RTP) conditions that are expected to occur in a main steam line break accident of Pressurized Water Reactors (PWRs). Using present CHF data, the applicability of conventional CHF correlations are investigated in a return-to-power condition. The CHF data have been collected for system pressures ranging from 0.47 to 15.06 MPa, mass flux from 49.66 to 654.44 kg/m{sup 2}s, inlet subcooling from 67.90 to 722.70 kJ/kg and exit quality from 0.36 to 1.29. In this study, the return-to-power conditions are defined as conditions with low mass flux less than 250 kg/m{sup 2}s, intermediated pressure between 6.0 MPa and 12.0 MPa, and high inlet subcooling greater than 200 kJ/kg. Total 299 CHF data including 93 CHF data in return-to-power conditions are obtained. The effects of various parameters on the CHF are consistent with previous understandings on the round tube CHF. Conventional CHF correlations predict the present return-to-power CHF data with reasonable accuracies. However, the prediction capabilities become worse in a very low mass flux below than about 100 kg/m{sup 2}s.

  17. Horizonte




    Este proyecto intenta ahondar en la idea de horizonte tratado desde la filosofía japonesa y de su nexo con el mundo occidental. De la necesidad latente de una restructuración de la educación para convertirla en una educación estética capaz de permitir a los individuos completarse plenamente como personas. A través de las enseñanzas orientales del zen, del haiku, de filósofos como Tanizaki, y sus ideas sobre la sombra y la sugerencia, frente a Kierkegaard o Schiller en el lado occidental y sus...

  18. An Experimental Investigation of the Effect of Condensate Inundation on Heat-Transfer in a Horizontal Tube Bundle. (United States)


    C-1) allows the isolation of the test condenser hotwell for condensate measurement. Since house steam was used as the steam supply system, the...Dans in Faiscean Tubulaire Horizontal," Department of Transfer and Conversion of Energy Service of Thermic Transfers, France, 1978. 13. Kline, S. J

  19. Natural convection heat transfer within horizontal spent nuclear fuel assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Canaan, R.E.


    Natural convection heat transfer is experimentally investigated in an enclosed horizontal rod bundle, which characterizes a spent nuclear fuel assembly during dry storage and/or transport conditions. The basic test section consists of a square array of sixty-four stainless steel tubular heaters enclosed within a water-cooled rectangular copper heat exchanger. The heaters are supplied with a uniform power generation per unit length while the surrounding enclosure is maintained at a uniform temperature. The test section resides within a vacuum/pressure chamber in order to subject the assembly to a range of pressure statepoints and various backfill gases. The objective of this experimental study is to obtain convection correlations which can be used in order to easily incorporate convective effects into analytical models of horizontal spent fuel systems, and also to investigate the physical nature of natural convection in enclosed horizontal rod bundles in general. The resulting data consist of: (1) measured temperatures within the assembly as a function of power, pressure, and backfill gas; (2) the relative radiative contribution for the range of observed temperatures; (3) correlations of convective Nusselt number and Rayleigh number for the rod bundle as a whole; and (4) correlations of convective Nusselt number as a function of Rayleigh number for individual rods within the array.

  20. Correlation for cross-flow resistance coefficient using STAR-CCM+ simulation data for flow of water through rod bundle supported by spacer grid with split-type mixing vane

    Energy Technology Data Exchange (ETDEWEB)

    Agbodemegbe, V.Y., E-mail: [Karlsruhe Institute of Technology, Institute of Fusion and Reactor Technique, Kaiserstrasse 12, Karlsruhe (Germany); Cheng, Xu, E-mail: [Karlsruhe Institute of Technology, Institute of Fusion and Reactor Technique, Kaiserstrasse 12, Karlsruhe (Germany); Akaho, E.H.K, E-mail: [School of Nuclear and Allied Sciences, University of Ghana, PO Box AE 1, Kwabenya, Accra (Ghana); Allotey, F.K.A, E-mail: [Institute of Mathematical Sciences, PO Box LG 197, Legon, Accra (Ghana)


    Highlights: • Investigate spacer grid with split-type mixing vanes. • Extent of predictability of experimental data by STAR-CCM+. • Reliability of two equation turbulence models. • Resistance to cross-flow through gaps. - Abstract: Mass transfer by diversion cross-flow through gaps is an important inter-subchannel interaction in fuel bundle of power reactors. It is normally due to the lateral pressure difference between adjacent sub-channels. This phenomenon is augmented in the presence of flow deflectors and is referred to as, directed cross-flow. Diversion cross-flow carries the momentum and energy of flow and hence affects the velocity and temperature profile in the rod bundle. The resistance to cross-flow in the transverse momentum equations is specified by the cross-flow resistant coefficient which is the subject of concern in the present study. In order to obtain data to correlate cross-flow resistance coefficient, computational fluid dynamic simulation using STAR-CCM+ was performed for flow of water at the bundle Reynolds number of Re1 = 3.4×10{sup 4} through a 5 × 5 rod bundle geometry supported by spacer grid with split mixing vanes for which the rod to rod pitch to diameter ratio was 1.33 and the rod to wall pitch to diameter ratio was 0.74. The two layer k-epsilon turbulence model with an all y+ automatic wall treatment function in STAR-CCM+ were adopted for an isothermal single phase (water) flow through the geometry. The objectives were to primarily investigate the extent of predictability of the experimental data by the computational fluid dynamic (CFD) simulation as a measure of reliability on the CFD code employed and also apply the simulation data to develop correlations for determining resistance coefficient to cross-flow. Validation of simulation results with experimental data showed good correlation of mean flow parameters with experimental data whiles turbulent fluctuations deviated largely from experimental trends. Generally, the

  1. Why (almost) all bundles are chiral (United States)

    Kost-Smith, Zachary V.; Blackwell, Robert A.; Glaser, Matthew A.


    We examine the self assembly of bundles of achiral hard rods with distributed, short-range attractive interactions. We show that in the majority of cases the equilibrium state of the bundle is chiral, with a double twist structure. We use biased Monte Carlo techniques and cell theory to compute the free energy as a function of an appropriately defined twist order parameter, and show that the formation of spontaneously chiral bundles is driven by maximization of orientational entropy. The finite curvature of the bundle boundary permits orientational escape, in which the circumferential angular range of motion of the rods is maximized for some finite average tilt. We map out the phase diagram of bundles in terms of the density, the ratio of rod length to bundle radius, L / R , and rod aspect ratio, L / D , and find transitions between untwisted, weakly twisted, and strongly twisted states. This work helps explain the common observation of twisted macroscopic bundles, and may provide insight into observations of twist in self-assembled membranes of colloidal rods.[2] This work funded by NSF MRSEC Grant DMR-0820579.

  2. Condensation heat transfer of a pure fluid and binary mixture outside a bundle of smooth horizontal tubes. Comparison of experimental results and a classical model

    Energy Technology Data Exchange (ETDEWEB)

    Belghazi, M.; Signe, J.C.; Marvillet, C. [Commissariat a l' Energie Atomique, Grenoble (France). Groupement pour la Recherche sur les Echangeurs Thermiques; Bontemps, A. [Universite Joseph Fourier, Grenoble (France)


    The condensation of pure HFC134a and different zeotropic mixtures with pure HFC134a and HFC23 on the outside of a bundle of smooth tubes was studied. The local heat transfer coefficient for each row was experimentally determined using a test section composed by a 13x3 staggered bundle of smooth copper tubes, measuring cooling water temperature in the inlet and the outlet of each tube, and measuring the vapour temperature along the bundle. All data were taken at the inlet vapour temperature of 40{sup o}C with a wall subcooling ranging from 4 to 26 K. The heat flux was varied from 5 to 30 kW/m{sup 2} and the cooling water flow rate from 120 to 300 1/h for each tube. The visualisation of the HFC134a condensate flow by means of transparent glass tubes reveals specific flow patterns and explains the difference between the measured values of the heat transfer coefficient and the calculated values from Nusselt's theory. On the other hand, the experimental heat transfer data with the binary mixtures HFC23-HFC134a show the important effects of temperature glide and the strong decrease of the heat transfer coefficient in comparison with the pure HFC134a data. The measured values with the different zeotropic mixtures were compared with the data calculated with the classical condensation model based on the equilibrium model. An improvement of this model is proposed. (author)

  3. Hydraulic characteristics of HANARO fuel bundles

    Energy Technology Data Exchange (ETDEWEB)

    Cho, S.; Chung, H. J.; Chun, S. Y.; Yang, S. K.; Chung, M. K. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)


    This paper presents the hydraulic characteristics measured by using LDV (Laser Doppler Velocimetry) in subchannels of HANARO, KAERI research reactor, fuel bundle. The fuel bundle consists of 18 axially finned rods with 3 spacer grids, which are arranged in cylindrical configuration. The effects of the spacer grids on the turbulent flow were investigated by the experimental results. Pressure drops for each component of the fuel bundle were measured, and the friction factors of fuel bundle and loss coefficients for the spacer grids were estimated from the measured pressure drops. Implications regarding the turbulent thermal mixing were discussed. Vibration test results measured by using laser vibrometer were presented. 9 refs., 12 figs. (Author)

  4. Rodding Surgery (United States)

    ... above-the-knee splint or lightweight plaster or fiberglass splint instead. Bracing may be used after the ... level. Potential Complications Complications from rodding surgery include risks related to:  General anesthesia,  Fractures during the procedure,  ...

  5. Non-abelian higher gauge theory and categorical bundle (United States)

    Viennot, David


    A gauge theory is associated with a principal bundle endowed with a connection permitting to define horizontal lifts of paths. The horizontal lifts of surfaces cannot be defined into a principal bundle structure. An higher gauge theory is an attempt to generalize the bundle structure in order to describe horizontal lifts of surfaces. A such attempt is particularly difficult for the non-abelian case. Some structures have been proposed to realize this goal (twisted bundle, gerbes with connection, bundle gerbe, 2-bundle). Each of them uses a category in place of the total space manifold of the usual principal bundle structure. Some of them replace also the structure group by a category (more precisely a Lie crossed module viewed as a category). But the base space remains still a simple manifold (possibly viewed as a trivial category with only identity arrows). We propose a new principal categorical bundle structure, with a Lie crossed module as structure groupoid, but with a base space belonging to a bigger class of categories (which includes non-trivial categories), that we called affine 2-spaces. We study the geometric structure of the categorical bundles built on these categories (which are a more complicated structure than the 2-bundles) and the connective structures on these bundles. Finally we treat an example interesting for quantum dynamics which is associated with the Bloch wave operator theory.

  6. Trivalent Cation Induced Bundle Formation of Filamentous fd Phages. (United States)

    Korkmaz Zirpel, Nuriye; Park, Eun Jin


    Bacteriophages are filamentous polyelectrolyte viral rods infecting only bacteria. In this study, we investigate the bundle formation of fd phages with trivalent cations having different ionic radii (Al(3+) , La(3+) and Y(3+) ) at various phage and counterion concentrations, and at varying bundling times. Aggregated phage bundles were detected at relatively low trivalent counterion concentrations (1 mM). Although 10 mM and 100 mM Y(3+) and La(3+) treatments formed larger and more intertwined phage bundles, Al(3+) and Fe(3+) treatments lead to the formation of networking filaments. Energy dispersive X-ray spectroscopy (EDX) analyses confirmed the presence of C, N and O peaks on densely packed phage bundles. Immunofluorescence labelling and ELISA analyses with anti-p8 antibodies showed the presence of phage filaments after bundling. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Some applications on tangent bundle with Kaluza-Klein metric

    Directory of Open Access Journals (Sweden)

    Murat Altunbaş


    Full Text Available In this paper, differential equations of geodesics; parallelism, incompressibility and closeness conditions of the horizontal and complete lift of the vector fields are investigated with respect to Kaluza-Klein metric on tangent bundle.

  8. Natural convection heat transfer for a staggered array of heated, horizontal cylinders within a rectangular enclosure

    Energy Technology Data Exchange (ETDEWEB)

    Triplett, C.E.


    This thesis presents the results of an experimental investigation of natural convection heat transfer in a staggered array of heated cylinders, oriented horizontally within a rectangular enclosure. The main purpose of this research was to extend the knowledge of heat transfer within enclosed bundles of spent nuclear fuel rods sealed within a shipping or storage container. This research extends Canaan`s investigation of an aligned array of heated cylinders that thermally simulated a boiling water reactor (BWR) spent fuel assembly sealed within a shipping or storage cask. The results are presented in terms of piecewise Nusselt-Rayleigh number correlations of the form Nu = C(Ra){sup n}, where C and n are constants. Correlations are presented both for individual rods within the array and for the array as a whole. The correlations are based only on the convective component of the heat transfer. The radiative component was calculated with a finite-element code that used measured surface temperatures, rod array geometry, and measured surface emissivities as inputs. The correlation results are compared to Canaan`s aligned array results and to other studies of natural convection in horizontal tube arrays.

  9. Engineering the bundled glass column: From the design concept to full-scale experimental testing

    NARCIS (Netherlands)

    Oikonomopoulou, F.; Bristogianni, T.; Veer, F.A.; Nijsse, R.

    This article gives an overview of the research conducted by the authors from the design concept to the engineering and full-scale testing of the bundled glass column. Consisting of adhesively bonded solid glass rods, the bundled column is a promising solution for transparent compressive members. To

  10. Multicell slug flow heat transfer analysis of finite LMFBR bundles

    Energy Technology Data Exchange (ETDEWEB)

    Yeung, M.K.; Wolf, L.


    An analytical two-dimensional, multi-region, multi-cell technique has been developed for the thermal analysis of LMFBR rod bundles. Local temperature fields of various unit cells were obtained for 7, 19, and 37-rod bundles of different geometries and power distributions. The validity of the technique has been verified by its excellent agreement with the THTB calculational result. By comparing the calculated fully-developed circumferential clad temperature distribution with those of the experimental measurements, an axial correction factor has been derived to account for the entrance effect for practical considerations. Moreover, the knowledge of the local temperature field of the rod bundle leads to the determination of the effective mixing lengths L/sub ij/ for adjacent subchannels of various geometries. It was shown that the implementation of the accurately determined L/sub ij/ into COBRA-IIIC calculations has fairly significant effects on intersubchannel mixing. In addition, a scheme has been proposed to couple the 2-D distributed and lumped parameter calculation by COBRA-IIIC such that the entrance effect can be implanted into the distributed parameter analysis. The technique has demonstrated its applicability for a 7-rod bundle and the results of calculation were compared to those of three-dimensional analyses and experimental measurements.

  11. Heat transfer and fluid friction in bundles of twisted tubes (United States)

    Dzyubenko, B. V.; Dreitser, G. A.


    The results of heat-transfer and friction studies in bundles of twisted tubes and rods with spiral wire-wrap spacers are analyzed, and recommendations are given for calculating the heat-transfer coefficient in heat exchangers using twisted tubes.

  12. Single Actin Bundle Rheology. (United States)

    Strehle, Dan; Mollenkopf, Paul; Glaser, Martin; Golde, Tom; Schuldt, Carsten; Käs, Josef A; Schnauß, Jörg


    Bundled actin structures play an essential role in the mechanical response of the actin cytoskeleton in eukaryotic cells. Although responsible for crucial cellular processes, they are rarely investigated in comparison to single filaments and isotropic networks. Presenting a highly anisotropic structure, the determination of the mechanical properties of individual bundles was previously achieved through passive approaches observing bending deformations induced by thermal fluctuations. We present a new method to determine the bending stiffness of individual bundles, by measuring the decay of an actively induced oscillation. This approach allows us to systematically test anisotropic, bundled structures. Our experiments revealed that thin, depletion force-induced bundles behave as semiflexible polymers and obey the theoretical predictions determined by the wormlike chain model. Thickening an individual bundle by merging it with other bundles enabled us to study effects that are solely based on the number of involved filaments. These thicker bundles showed a frequency-dependent bending stiffness, a behavior that is inconsistent with the predictions of the wormlike chain model. We attribute this effect to internal processes and give a possible explanation with regard to the wormlike bundle theory.

  13. Single Actin Bundle Rheology

    Directory of Open Access Journals (Sweden)

    Dan Strehle


    Full Text Available Bundled actin structures play an essential role in the mechanical response of the actin cytoskeleton in eukaryotic cells. Although responsible for crucial cellular processes, they are rarely investigated in comparison to single filaments and isotropic networks. Presenting a highly anisotropic structure, the determination of the mechanical properties of individual bundles was previously achieved through passive approaches observing bending deformations induced by thermal fluctuations. We present a new method to determine the bending stiffness of individual bundles, by measuring the decay of an actively induced oscillation. This approach allows us to systematically test anisotropic, bundled structures. Our experiments revealed that thin, depletion force-induced bundles behave as semiflexible polymers and obey the theoretical predictions determined by the wormlike chain model. Thickening an individual bundle by merging it with other bundles enabled us to study effects that are solely based on the number of involved filaments. These thicker bundles showed a frequency-dependent bending stiffness, a behavior that is inconsistent with the predictions of the wormlike chain model. We attribute this effect to internal processes and give a possible explanation with regard to the wormlike bundle theory.

  14. Single-Phase Bundle Flows Including Macroscopic Turbulence Model

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Seung Jun; Yoon, Han Young [KAERI, Daejeon (Korea, Republic of); Yoon, Seok Jong; Cho, Hyoung Kyu [Seoul National University, Seoul (Korea, Republic of)


    To deal with various thermal hydraulic phenomena due to rapid change of fluid properties when an accident happens, securing mechanistic approaches as much as possible may reduce the uncertainty arising from improper applications of the experimental models. In this study, the turbulence mixing model, which is well defined in the subchannel analysis code such as VIPRE, COBRA, and MATRA by experiments, is replaced by a macroscopic k-e turbulence model, which represents the aspect of mathematical derivation. The performance of CUPID with macroscopic turbulence model is validated against several bundle experiments: CNEN 4x4 and PNL 7x7 rod bundle tests. In this study, the macroscopic k-e model has been validated for the application to subchannel analysis. It has been implemented in the CUPID code and validated against CNEN 4x4 and PNL 7x7 rod bundle tests. The results showed that the macroscopic k-e turbulence model can estimate the experiments properly.

  15. Cytoskeletal bundle mechanics

    NARCIS (Netherlands)

    Bathe, Mark; Heussinger, Claus; Claessens, Mireille Maria Anna Elisabeth; Bausch, Andreas R.; Frey, Erwin


    The mechanical properties of cytoskeletal actin bundles play an essential role in numerous physiological processes, including hearing, fertilization, cell migration, and growth. Cells employ a multitude of actin-binding proteins to actively regulate bundle dimensions and cross-linking properties to

  16. Dynamic behavior of upper hydraulic drive control rod

    Energy Technology Data Exchange (ETDEWEB)

    Li Xiaotian [Institute of Nuclear and New Energy Technology, Beijing 100084 (China)]. E-mail:; He Shuyan [Institute of Nuclear and New Energy Technology, Beijing 100084 (China)


    A 200 MW nuclear heating reactor (NHR) was developed based on the 5 MW testing heating reactor (THR-5). In order to improve its features, the INET was used to optimize its structure design. One task was to design the upper hydraulic drive control rod, which is located at the upper part of the reactor core, so that the fuel rod in each corner of the bundle will not be removed as they are in the THR-5. A program based on the method of characteristics was run to investigate the dynamic behavior of the upper hydraulic control rod drive system. The steady-state and dynamic characteristics of the control rod were studied. The influence of the reactor temperature and structure parameters on the operation reliability was investigated. Finally the optimal design parameters of the upper hydraulic drive control rod were obtained.

  17. The ABCDEF Implementation Bundle

    Directory of Open Access Journals (Sweden)

    Annachiara Marra


    Full Text Available Long-term morbidity, long-term cognitive impairment and hospitalization-associated disability are common occurrence in the survivors of critical illness, with significant consequences for patients and for the caregivers. The ABCDEF bundle represents an evidence-based guide for clinicians to approach the organizational changes needed for optimizing ICU patient recovery and outcomes. The ABCDEF bundle includes: Assess, Prevent, and Manage Pain, Both Spontaneous Awakening Trials (SAT and Spontaneous Breathing Trials (SBT, Choice of analgesia and sedation, Delirium: Assess, Prevent, and Manage, Early mobility and Exercise, and Family engagement. The purpose of this review is to describe the core features of the ABCDEF bundle.

  18. Tie rod insertion test

    CERN Multimedia



    The superconducting coil is inserted in the outer vaccum tank and supported by a set of tie rods. These tie rods are made of titanium alloy. This test reproduce the final insertion of the tie rods inside the outer vacuum tank.

  19. Bundle Branch Block (United States)

    ... 2015. Bundle branch block Symptoms & causes Diagnosis & treatment Advertisement Mayo Clinic does not endorse companies or products. ... a Job Site Map About This Site Twitter Facebook Google YouTube Pinterest Mayo Clinic is a not- ...

  20. Thermodynamics of fiber bundles


    Pride, Steven R.; Toussaint, Renaud


    A recent theory that determines the properties of disordered solids as the solid accumulates damage is applied to the special case of fiber bundles with global load sharing and is shown to be exact in this case. The theory postulates that the probability of observing a given emergent damage state is obtained by maximizing the emergent entropy as defined by Shannon subject to energetic constraints. This theory yields the known exact results for the fiber-bundle model with global load sharing a...

  1. Right bundle branch block

    DEFF Research Database (Denmark)

    Bussink, Barbara E; Holst, Anders Gaarsdal; Jespersen, Lasse


    AimsTo determine the prevalence, predictors of newly acquired, and the prognostic value of right bundle branch block (RBBB) and incomplete RBBB (IRBBB) on a resting 12-lead electrocardiogram in men and women from the general population.Methods and resultsWe followed 18 441 participants included.......5%/2.3% in women, P Right bundle branch block was associated with significantly...... increased all-cause and cardiovascular mortality in both genders with age-adjusted hazard ratios (HR) of 1.31 [95% confidence interval (CI), 1.11-1.54] and 1.87 (95% CI, 1.48-2.36) in the gender pooled analysis with little attenuation after multiple adjustment. Right bundle branch block was associated...

  2. Bundles of Banach algebras

    Directory of Open Access Journals (Sweden)

    J. W. Kitchen


    Full Text Available We study bundles of Banach algebras π:A→X, where each fiber Ax=π−1({x} is a Banach algebra and X is a compact Hausdorff space. In the case where all fibers are commutative, we investigate how the Gelfand representation of the section space algebra Γ(π relates to the Gelfand representation of the fibers. In the general case, we investigate how adjoining an identity to the bundle π:A→X relates to the standard adjunction of identities to the fibers.

  3. Horizontal Accelerator (United States)

    Federal Laboratory Consortium — The Horizontal Accelerator (HA) Facility is a versatile research tool available for use on projects requiring simulation of the crash environment. The HA Facility is...

  4. Buying bundles: the effects of bundle attributes on the value of bundling


    Linthorst, M.M.; Telgen, Jan; Schotanus, Fredo


    We consider the situation in which a buyer has to find the optimal degree of bundling for buying goods and services. From a review of the literature we develop attributes associated with bundling. Each of these attributes has an effect on the value of a bundle. Combined, the attributes determine the value of a bundle. We describe how the various attributes of a bundle contribute to the value of a bundle given the context of the buying situation. Based on interviews, a further analysis of bund...

  5. Buying bundles: the effects of bundling attributes on the value of bundling


    Linthorst, M.M.; Telgen, Jan; Schotanus, Fredo


    We consider the situation in which a buyer has to find the optimal degree of bundling for buying goods and services. From a review of the literature we develop attributes associated with bundling. Each of these attributes has an effect on the value of a bundle. Combined, the attributes determine the value of a bundle. We describe how the various attributes of a bundle contribute to the value of a bundle given the context of the buying situation. Based on interviews, a further analysis of bund...

  6. Fuel-rod temperature transients during LWR degraded-core accidents

    Energy Technology Data Exchange (ETDEWEB)

    Briscoe, F; Rivard, J B; Young, M F


    Heat transfer models of fuel rods and coolant have been developed in support of LWR damaged fuel studies underway at Sandia National Laboratories for the NRC. A one-dimensional, full-length model simulates a PWR fuel rod; a two-dimensional, 0.5 m model simulates 9-rod bundle experiments to be performed in the Annular Core Research Reactor. The models include zircaloy oxidation, heat transfer by convecting steam/hydrogen flow, and radiation between surfaces through an absorbing/emitting gas. Characteristics of the one-dimensional reactor fuel rod model for two types of accident sequence are reported, as well as comparisons with MARCH code results.


    Directory of Open Access Journals (Sweden)



    Full Text Available In municipal solid waste, aluminum is the main nonferrous metal, approximately 80- 85% of the total nonferrous metals. The income per ton gained from aluminum recuperation is 20 times higher than from glass, steel boxes or paper recuperation. The object of this paper is the design of a 300 kN press for aluminum box bundling.

  8. Dynamics of flagellar bundling (United States)

    Janssen, Pieter; Graham, Michael


    Flagella are long thin appendages of microscopic organisms used for propulsion in low-Reynolds environments. For E. coli the flagella are driven by a molecular motor, which rotates the flagella in a counter-clockwise motion (CCM). When in a forward swimming motion, all flagella bundle up. If a motor reverses rotation direction, the flagella unbundle and the cell makes a tumbling motion. When all motors turn in the same CC direction again, the flagella bundle up, and forward swimming continues. To investigate the bundling, we consider two flexible helices next to each other, as well as several flagella attached to a spherical body. Each helix is modeled as several prolate spheroids connected at the tips by springs. For hydrodynamic interactions, we consider the flagella to made up of point forces, while the finite size of the body is incorporated via Fax'en's laws. We show that synchronization occurs quickly relative to the bundling process. For flagella next to each other, the initial deflection is generated by rotlet interactions generated by the rotating helices. At longer times, simulations show the flagella only wrap once around each other, but only for flagella that are closer than about 4 helix radii. Finally, we show a run-and-tumble motion of the body with attached flagella.

  9. Why Rods and Cocci

    Indian Academy of Sciences (India)

    Bacteria exhibit a wide variety of shapes but the commonly studied species of bacteria are generally either spherical in shape which are called cocci (singular coccus) or have a cylindrical shape and are called rods or bacilli (singular bacillus). In reality rods and cocci are the ends of a continuum. Sonle of the cocci are.

  10. 3-D slug flow heat transfer analysis of coupled coolant cells in finite LMFBR bundles

    Energy Technology Data Exchange (ETDEWEB)

    Wong, C.N.; Wolf, L.


    A three-dimensional single region slug flow heat transfer analysis for finite LMFBR rod bundles using a classical analytical solution method has been performed. According to the isolated single cell analysis, the results show that the peripheral clad temperature variation as well as the thermal entrance length are strongly dependent upon the degree of irregularity displayed by various coolant geometries. Since under the present LMFBR conditions, fully-developed temperature fields may hardly be established in such characteristic rod bundle regions, a 3-D heat transfer analysis seems to be mandatory. This implies that the results of fully developed heat transfer analyses are by far too conservative.

  11. Bundle pricing with comparable items

    NARCIS (Netherlands)

    Grigoriev, Alexander; van Loon, Joyce; Sviridenko, Maxim; Uetz, Marc Jochen; Vredeveld, Tjark; Arge, L.; Hoffmann, M.; Welzl, E.


    We consider a revenue maximization problem where we are selling a set of items, each available in a certain quantity, to a set of bidders. Each bidder is interested in one or several bundles of items. We assume the bidders’ valuations for each of these bundles to be known. Whenever bundle prices are

  12. Bundling ecosystem services in Denmark

    DEFF Research Database (Denmark)

    Turner, Katrine Grace; Odgaard, Mette Vestergaard; Bøcher, Peder Klith


    to form synergies. We identified six distinct ecosystem service bundle types, indicating multiple interactions at a landscape level. The bundle types showed specialized areas of agricultural production, high provision of cultural services at the coasts, multifunctional mixed-use bundle types around urban...

  13. Buying bundles: the effects of bundling attributes on the value of bundling

    NARCIS (Netherlands)

    Linthorst, M.M.; Telgen, Jan; Schotanus, Fredo


    We consider the situation in which a buyer has to find the optimal degree of bundling for buying goods and services. From a review of the literature we develop attributes associated with bundling. Each of these attributes has an effect on the value of a bundle. Combined, the attributes determine the

  14. Buying bundles: the effects of bundle attributes on the value of bundling

    NARCIS (Netherlands)

    Linthorst, M.M.; Telgen, Jan; Schotanus, Fredo


    We consider the situation in which a buyer has to find the optimal degree of bundling for buying goods and services. From a review of the literature we develop attributes associated with bundling. Each of these attributes has an effect on the value of a bundle. Combined, the attributes determine the

  15. Control rod testing apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Gaunt, R.R.; Ashman, C.M.


    A control rod testing apparatus is described comprising: a first guide means having a vertical cylindrical opening for grossly guiding a control rod; a second guide means having a vertical cylindrical opening for grossly guiding a control rod. The first and second guide means are supported at axially spaced locations with the openings coaxial; and a substantially cylindrical subassembly having a vertical cylindrical opening therethrough. The subassembly is trapped coaxial with and between the first and second guide means, and the subassembly radially floats with respect to the first and second guide means.

  16. Helices and vector bundles

    CERN Document Server

    Rudakov, A N


    This volume is devoted to the use of helices as a method for studying exceptional vector bundles, an important and natural concept in algebraic geometry. The work arises out of a series of seminars organised in Moscow by A. N. Rudakov. The first article sets up the general machinery, and later ones explore its use in various contexts. As to be expected, the approach is concrete; the theory is considered for quadrics, ruled surfaces, K3 surfaces and P3(C).

  17. Bundling harvester; Nippukorjausharvesteri

    Energy Technology Data Exchange (ETDEWEB)

    Koponen, K. [Eko-Log Oy, Kuopio (Finland)


    The staring point of the project was to design and construct, by taking the silvicultural point of view into account, a harvesting and processing system especially for energy-wood, containing manually driven bundling harvester, automatizing of the harvester, and automatized loading. The equipment forms an ideal method for entrepreneur`s-line harvesting. The target is to apply the system also for owner`s-line harvesting. The profitability of the system promotes the utilization of the system in both cases. The objectives of the project were: to construct a test equipment and prototypes for all the project stages, to carry out terrain and strain tests in order to examine the usability and durability, as well as the capacity of the machine, to test the applicability of the Eko-Log system in simultaneous harvesting of energy and pulp woods, and to start the marketing and manufacturing of the products. The basic problems of the construction of the bundling harvester have been solved using terrain-tests. The prototype machine has been shown to be operable. Loading of the bundles to form sufficiently economically transportable loads has been studied, and simultaneously, the branch-biomass has been tried to be utilized without loosing the profitability of transportation. The results have been promising, and will promote the profitable utilization of wood-energy

  18. Axial Rod Coupling Design

    National Research Council Canada - National Science Library

    Smith, David R


    .... The axial rod and coupling has been designed to withstand external survival loads ( 8.3 kN (1,870 lb) for Ring 5), and to maintain its length to within 7 microns after disassembly and reassembly...

  19. Bundled payments in orthopedic surgery. (United States)

    Bushnell, Brandon D


    As a result of reading this article, physicians should be able to: 1. Describe the concept of bundled payments and the potential applications of bundled payments in orthopedic surgery. 2. For specific situations, outline a clinical episode of care, determine the participants in a bundling situation, and define care protocols and pathways. 3. Recognize the importance of resource utilization management, quality outcome measurement, and combined economic-clinical value in determining the value of bundled payment arrangements. 4. Identify the implications of bundled payments for practicing orthopedists, as well as the legal issues and potential future directions of this increasingly popular alternative payment method. Bundled payments, the idea of paying a single price for a bundle of goods and services, is a financial concept familiar to most American consumers because examples appear in many industries. The idea of bundled payments has recently gained significant momentum as a financial model with the potential to decrease the significant current costs of health care. Orthopedic surgery as a field of medicine is uniquely positioned for success in an environment of bundled payments. This article reviews the history, logistics, and implications of the bundled payment model relative to orthopedic surgery. Copyright 2015, SLACK Incorporated.

  20. Muon bundles from the Universe

    Directory of Open Access Journals (Sweden)

    Kankiewicz P.


    Full Text Available Recently the CERN ALICE experiment, in its dedicated cosmic ray run, observed muon bundles of very high multiplicities, thereby confirming similar findings from the LEP era at CERN (in the CosmoLEP project. Significant evidence for anisotropy of arrival directions of the observed high multiplicity muonic bundles is found. Estimated directionality suggests their possible extragalactic provenance. We argue that muonic bundles of highest multiplicity are produced by strangelets, hypothetical stable lumps of strange quark matter infiltrating our Universe.

  1. Bundle Formation in Biomimetic Hydrogels

    NARCIS (Netherlands)

    Jaspers, Maarten; Pape, A C H; Voets, Ilja K; Rowan, Alan E; Portale, Giuseppe; Kouwer, Paul H J


    Bundling of single polymer chains is a crucial process in the formation of biopolymer network gels that make up the extracellular matrix and the cytoskeleton. This bundled architecture leads to gels with distinctive properties, including a large-pore-size gel formation at very low concentrations and

  2. Bundle Security Protocol for ION (United States)

    Burleigh, Scott C.; Birrane, Edward J.; Krupiarz, Christopher


    This software implements bundle authentication, conforming to the Delay-Tolerant Networking (DTN) Internet Draft on Bundle Security Protocol (BSP), for the Interplanetary Overlay Network (ION) implementation of DTN. This is the only implementation of BSP that is integrated with ION.

  3. Fiber bundle phase conjugate mirror (United States)

    Ward, Benjamin G.


    An improved method and apparatus for passively conjugating the phases of a distorted wavefronts resulting from optical phase mismatch between elements of a fiber laser array are disclosed. A method for passively conjugating a distorted wavefront comprises the steps of: multiplexing a plurality of probe fibers and a bundle pump fiber in a fiber bundle array; passing the multiplexed output from the fiber bundle array through a collimating lens and into one portion of a non-linear medium; passing the output from a pump collection fiber through a focusing lens and into another portion of the non-linear medium so that the output from the pump collection fiber mixes with the multiplexed output from the fiber bundle; adjusting one or more degrees of freedom of one or more of the fiber bundle array, the collimating lens, the focusing lens, the non-linear medium, or the pump collection fiber to produce a standing wave in the non-linear medium.

  4. An in vitro biomechanical comparison of anterior cruciate ligament reconstruction: single bundle versus anatomical double bundle techniques

    Directory of Open Access Journals (Sweden)

    Sandra Umeda Sasaki


    Full Text Available INTRODUCTION: Anterior cruciate ligament ruptures are frequent, especially in sports. Surgical reconstruction with autologous grafts is widely employed in the international literature. Controversies remain with respect to technique variations as continuous research for improvement takes place. One of these variations is the anatomical double bundle technique, which is performed instead of the conventional single bundle technique. More recently, there has been a tendency towards positioning the two bundles through double bone tunnels in the femur and tibia (anatomical reconstruction. OBJECTIVES: To compare, through biomechanical tests, the practice of anatomical double bundle anterior cruciate ligament reconstruction with a patellar graft to conventional single bundle reconstruction with the same amount of patellar graft in a paired experimental cadaver study. METHODS: Nine pairs of male cadaver knees ranging in age from 44 to 63 years were randomized into two groups: group A (single bundle and group B (anatomical reconstruction. Each knee was biomechanically tested under three conditions: intact anterior cruciate ligament, reconstructed anterior cruciate ligament, and injured anterior cruciate ligament. Maximum anterior dislocation, rigidity, and passive internal tibia rotation were recorded with knees submitted to a 100 N horizontal anterior dislocation force applied to the tibia with the knees at 30, 60 and 90 degrees of flexion. RESULTS: There were no differences between the two techniques for any of the measurements by ANOVA tests. CONCLUSION: The technique of anatomical double bundle reconstruction of the anterior cruciate ligament with bone-patellar tendon-bone graft has a similar biomechanical behavior with regard to anterior tibial dislocation, rigidity, and passive internal tibial rotation.

  5. Morphoelastic rods. Part I: A single growing elastic rod

    KAUST Repository

    Moulton, D.E.


    A theory for the dynamics and statics of growing elastic rods is presented. First, a single growing rod is considered and the formalism of three-dimensional multiplicative decomposition of morphoelasticity is used to describe the bulk growth of Kirchhoff elastic rods. Possible constitutive laws for growth are discussed and analysed. Second, a rod constrained or glued to a rigid substrate is considered, with the mismatch between the attachment site and the growing rod inducing stress. This stress can eventually lead to instability, bifurcation, and buckling. © 2012 Elsevier Ltd. All rights reserved.

  6. Development boiling to sprinkled tube bundle

    Directory of Open Access Journals (Sweden)

    Kracík Petr


    Full Text Available This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes’ interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.


    Miller, G.


    A nuclear reactor control rod mechanism is designed which mechanically moves the control rods into and out of the core under normal conditions but rapidly forces the control rods into the core by catapultic action in the event of an emergency. (AEC)

  8. Semiflexible Biopolymers in Bundled Arrangements

    Directory of Open Access Journals (Sweden)

    Jörg Schnauß


    Full Text Available Bundles and networks of semiflexible biopolymers are key elements in cells, lending them mechanical integrity while also enabling dynamic functions. Networks have been the subject of many studies, revealing a variety of fundamental characteristics often determined via bulk measurements. Although bundles are equally important in biological systems, they have garnered much less scientific attention since they have to be probed on the mesoscopic scale. Here, we review theoretical as well as experimental approaches, which mainly employ the naturally occurring biopolymer actin, to highlight the principles behind these structures on the single bundle level.

  9. MAVEN EUV Modelled Data Bundle (United States)

    National Aeronautics and Space Administration — This bundle contains solar irradiance spectra in 1-nm bins from 0-190 nm. The spectra are generated based upon the Flare Irradiance Spectra Model - Mars (FISM-M)...

  10. Left bundle-branch block

    DEFF Research Database (Denmark)

    Risum, Niels; Strauss, David; Sogaard, Peter


    The relationship between myocardial electrical activation by electrocardiogram (ECG) and mechanical contraction by echocardiography in left bundle-branch block (LBBB) has never been clearly demonstrated. New strict criteria for LBBB based on a fundamental understanding of physiology have recently...

  11. MAVEN SWEA Calibrated Data Bundle (United States)

    National Aeronautics and Space Administration — This bundle contains fully calibrated electron energy/angle (3D) distributions, pitch angle distributions, and omni-directional energy spectra. Tables of sensitivity...

  12. MAVEN LPW Derived Data Bundle (United States)

    National Aeronautics and Space Administration — This bundle contains data which have been derived from other data products or determined by fits to other data. These are science quality data produced by the LPW...

  13. MAVEN LPW Calibrated Data Bundle (United States)

    National Aeronautics and Space Administration — This bundle contains fully calibrated, science quality data produced by the LPW instrument. The data include spacecraft potential, electric field waveforms and wave...

  14. Evaluation of nonequilibrium effects in bundle dispersed-flow film boiling. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Morris, D.G.; Mullins, C.B.; Yoder, G.L.


    The effects of thermodynamic nonequilibrium in dispersed flow film boiling heat transfer are examined. Steady-state and transient rod-bundle data are used to evaluate several empirical heat-transfer models commonly employed to predict post-CHF behavior. The models that account for thermodynamic nonequilibrium perform adequately, while those that ignore nonequilibrium effects incur errors in wall superheat as high as 190/sup 0/K. Nonequilibrium effects can also be treated by explicitly modeling the phenomena. The thermal-hydraulic code COBRA-TF employs this approach. Using bundle data, the models in the code are evaluated. Analysis suggests that the interfacial heat transfer is overpredicted.

  15. Cone rod dystrophies

    Directory of Open Access Journals (Sweden)

    Hamel Christian P


    Full Text Available Abstract Cone rod dystrophies (CRDs (prevalence 1/40,000 are inherited retinal dystrophies that belong to the group of pigmentary retinopathies. CRDs are characterized by retinal pigment deposits visible on fundus examination, predominantly localized to the macular region. In contrast to typical retinitis pigmentosa (RP, also called the rod cone dystrophies (RCDs resulting from the primary loss in rod photoreceptors and later followed by the secondary loss in cone photoreceptors, CRDs reflect the opposite sequence of events. CRD is characterized by primary cone involvement, or, sometimes, by concomitant loss of both cones and rods that explains the predominant symptoms of CRDs: decreased visual acuity, color vision defects, photoaversion and decreased sensitivity in the central visual field, later followed by progressive loss in peripheral vision and night blindness. The clinical course of CRDs is generally more severe and rapid than that of RCDs, leading to earlier legal blindness and disability. At end stage, however, CRDs do not differ from RCDs. CRDs are most frequently non syndromic, but they may also be part of several syndromes, such as Bardet Biedl syndrome and Spinocerebellar Ataxia Type 7 (SCA7. Non syndromic CRDs are genetically heterogeneous (ten cloned genes and three loci have been identified so far. The four major causative genes involved in the pathogenesis of CRDs are ABCA4 (which causes Stargardt disease and also 30 to 60% of autosomal recessive CRDs, CRX and GUCY2D (which are responsible for many reported cases of autosomal dominant CRDs, and RPGR (which causes about 2/3 of X-linked RP and also an undetermined percentage of X-linked CRDs. It is likely that highly deleterious mutations in genes that otherwise cause RP or macular dystrophy may also lead to CRDs. The diagnosis of CRDs is based on clinical history, fundus examination and electroretinogram. Molecular diagnosis can be made for some genes, genetic counseling is

  16. Results of Post Irradiation Examinations of VVER Leaky Rods

    Energy Technology Data Exchange (ETDEWEB)

    Markov, D.; Perepelkin, S.; Polenok, V.; Zhitelev, V.; Mayorshina, G. [Head of Fuel Research Department, JSC ' SSC RIAR' , 433510, Dimitrovgrad-10, Ulyanovsk region (Russian Federation)


    Cs yield from the rod meat goes beyond the cladding. Thus, the reduction of fission yield from the failed rod into the coolant may be reached by the decrease of its power. To reduce the number of fuel rod leakages under operation it is necessary to: - mount special filters on the fuel assemblies preventing penetration of foreign particles in the rod bundle; - optimize the fuel assembly design, in order to reduce vibration of the fuel assembly components; - optimize the fabrication process and fuel rod quality control. (authors)

  17. GPU Parallel Bundle Block Adjustment

    Directory of Open Access Journals (Sweden)

    ZHENG Maoteng


    Full Text Available To deal with massive data in photogrammetry, we introduce the GPU parallel computing technology. The preconditioned conjugate gradient and inexact Newton method are also applied to decrease the iteration times while solving the normal equation. A brand new workflow of bundle adjustment is developed to utilize GPU parallel computing technology. Our method can avoid the storage and inversion of the big normal matrix, and compute the normal matrix in real time. The proposed method can not only largely decrease the memory requirement of normal matrix, but also largely improve the efficiency of bundle adjustment. It also achieves the same accuracy as the conventional method. Preliminary experiment results show that the bundle adjustment of a dataset with about 4500 images and 9 million image points can be done in only 1.5 minutes while achieving sub-pixel accuracy.

  18. Twist-off purification of hair bundles. (United States)

    Shin, Jung-Bum; Pagana, James; Gillespie, Peter G


    Purification of hair bundles from inner-ear organs allows biochemical analysis of bundle constituents, including proteins and lipids. We describe here the "twist-off" method of bundle isolation, where dissected inner-ear organs are embedded in agarose, then subjected to a mechanical disruption that shears off bundles and leaves them in agarose blocks. With care in the dissection and in clean-up of the isolated bundles, contamination from cell bodies can be kept to a minimum. Isolated bundles can be analyzed by a variety of techniques, including immunocytochemistry, SDS-PAGE, immunoblotting, and mass spectrometry.

  19. Principal bundles the classical case

    CERN Document Server

    Sontz, Stephen Bruce


    This introductory graduate level text provides a relatively quick path to a special topic in classical differential geometry: principal bundles.  While the topic of principal bundles in differential geometry has become classic, even standard, material in the modern graduate mathematics curriculum, the unique approach taken in this text presents the material in a way that is intuitive for both students of mathematics and of physics. The goal of this book is to present important, modern geometric ideas in a form readily accessible to students and researchers in both the physics and mathematics communities, providing each with an understanding and appreciation of the language and ideas of the other.

  20. Measurement of nuclear fuel rod deformation using an image processing technique

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Jai Wan; Choi, Young Soo; Jeong, Kyung Min [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Shin, Jung Cheol [KEPCO Nuclear Fuel, Daejeon (Korea, Republic of)


    In this paper, a deformation measurement technology for nuclear fuel rods is proposed. The deformation measurement system includes a high-definition CMOS image sensor, a lens, a semiconductor laser line beam marker, and optical and mechanical accessories. The basic idea of the proposed deformation measurement system is to illuminate the outer surface of a fuel rod with a collimated laser line beam at an angle of 45 degrees or higher. For this method, it is assumed that a nuclear fuel rod and the optical axis of the image sensor for observing the rod are vertically composed. The relative motion of the fuel rod in the horizontal direction causes the illuminated laser line beam to move vertically along the surface of the fuel rod. The resulting change of the laser line beam position on the surface of the fuel rod is imaged as a parabolic beam in the high definition CMOS image sensor. An ellipse model is then extracted from the parabolic beam pattern. The center coordinates of the ellipse model are taken as the feature of the deformed fuel rod. The vertical offset of the feature point of the nuclear fuel rod is derived based on the displacement of the offset in the horizontal direction. Based on the experimental results for a nuclear fuel rod sample with a formation of surface crud, an inspection resolution of 50 is achieved using the proposed method. In terms of the degree of precision, this inspection resolution is an improvement of more than 300% from a 150 {mu}m resolution, which is the conventional measurement criteria required for the deformation of neutron irradiated fuel rods

  1. Experimental Investigation on the Thermal Mixing Characteristics of the Wire Wrapped 37 Rods Using a Laser Induced Fluorescence Technique

    Energy Technology Data Exchange (ETDEWEB)

    Kim, S.; Choi, H. S.; Choi, S. R.; Kim, H. M.; Bae, H.; Chang, S. K.; Euh, D. J.; Lee, H. Y. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    The Nuclear Power Committee has established the objectives of the construction and the operation of the 4th generation LMFBR (Liquid Metal Fast Breed Reactor). To meet these goals, one of the subjects which is performing the production of the experimental data and also is estimating the uncertainties of the results of the CFD analysis should be undertaken. In other words, it is important to evaluate the accuracy of the model and the thermal hydraulic analysis code used to evaluate the safety of the SFR reactor core and quantify uncertainty. For the preliminary test before the 127 pin model test, the test loop for the wire wrapped 37 pin fuel assembly (FIFFA, Flow Identification for Fast reactor Fuel Assembly) was constructed to establish measurement technique. The heat transfer associated with the flow exchange between rod bundles was related with the diffusion coefficient. To identify a mixing characteristics among rod bundles, the optical measurement technique was adopted. To visualize and quantify the mixing characteristics between each rod bundle, the laser induced fluorescence (LIF) technique is one of suitable measurement technique. The CFD-grade experimental results will contribute to provide the benchmark data for validating the CFD analysis. LIF technique is adopted to visualize and quantify the mixing characteristics between each rod bundle in this study. The mixing characteristics data of reactor flow distribution will be utilized to evaluate and to validate the thermal margin analysis of the SFR reactor.

  2. ADE bundles over surfaces with ADE singularities


    Chen, Yunxia; Leung, Naichung Conan


    Given a complex projective surface with an ADE singularity and p_{g}=0, we construct ADE bundles over it and its minimal resolution. Furthermore, we descibe their minuscule representation bundles in terms of configurations of (reducible) (-1)-curves.

  3. PDS4 Bundle Creation Governance Using BPMN (United States)

    Radulescu, C.; Levoe, S. R.; Algermissen, S. S.; Rye, E. D.; Hardman, S. H.


    The AMMOS-PDS Pipeline Service (APPS) provides a Bundle Builder tool, which governs the process of creating, and ultimately generates, PDS4 bundles incrementally, as science products are being generated.

  4. Stability evaluation of the rod in triangular array predicted by CFD (United States)

    Upnere, S.; Jekabsons, N.


    Stability boundaries of structures consisting of circular cylinder arrays in the cross-flow are different from case to case depending on geometrical and mechanical variations of the rod bundle layout as well as depending on nature of the flow field, requiring an individual set of experiments for each characteristic case. In this study, close-packed staggered rod bundle with a pitch-to-diameter ratio of 1.1 is analysed. Numerical modelling has been done to check the stability threshold (critical velocity) of a flexibly mounted rod in an otherwise fixed rods array. The computational domain consists of the rod array with 6 rows of five cylinders. The unsteady flow through triangular cylinder array has been simulated using two-dimensional URANS computations with an open source Computational Fluid Dynamics (CFD) code. The CFD calculations are coupled with the six degree-of-freedom rigid body motion solver with reduced degree-of-freedom. Results were compared with the analytically determined threshold values.

  5. Developing the bundled glass column

    NARCIS (Netherlands)

    Oikonomopoulou, F.; Bristogianni, T; Veer, F.A.; Nijsse, R.; da Sousa Cruz, Paulo J.

    In this paper a bundled glass column is presented as a promising solution for a completely transparent, almost dematerialized structural compressive element. The aim is to ob-tain a glass column that can safely carry loads, achieve a high visual result and be relatively eas-ily manufactured.

  6. Line bundles and flat connections

    Indian Academy of Sciences (India)

    /fulltext/pmsc/127/03/0547-0549. Keywords. Calabi–Yau threefold; torsion; cocompact lattice; unitary representation. Abstract. We prove that there are cocompact lattices Γ in S L ( 2 , C ) with the property that there are holomorphic line bundles ...

  7. Line bundles and flat connections

    Indian Academy of Sciences (India)

    Calabi–Yau threefold; torsion; cocompact lattice; unitary representation. 2000 Mathematics Subject Classification. 81T30, 14D21, 53C07. 1. Stable bundles and unitary flat connections. 1.1 Admitting flat connections. Let X be a compact connected complex manifold of complex dimension δ. Let ω be the. (1, 1)-form on X ...

  8. Combustion of solid carbon rods in zero and normal gravity (United States)

    Spuckler, C. M.; Kohl, F. J.; Miller, R. A.; Stearns, C. A.; De Witt, K. J.


    In order to investigate the mechanism of carbon combustion, normal and zero gravity experiments were conducted in which spectroscopic carbon rods were resistance ignited and burned in an oxygen environment. Direct mass spectrometric sampling was used in the normal gravity tests to measure gas phase concentrations. The gas sampling probe was positioned near the circumference of the horizontally mounted carbon rods, either at the top or at angles of 45 or 90 deg from the top, and yielded concentration profiles of CO2, CO, and O2 as a function of distance from the carbon surface. The experimental concentrations were compared to those predicted by a stagnant film model. Zero gravity droptower tests were conducted in order to assess the effect of convection on the normal gravity combustion process. The ratio of flame diameter to rod diameter as a function of time for oxygen pressures of 5, 10, 15, and 20 psia was obtained for three different diameter rods. It was found that this ratio was inversely proportional to both the oxygen pressure and the rod diameter.

  9. Chemical vapor infiltration in single fiber bundles

    Energy Technology Data Exchange (ETDEWEB)

    Devlin, D.J.; Barbero, R.S.; Currier, R.P.


    Chemical vapor infiltration (CVI) in single fiber bundles is studied under isothermal conditions. Understanding infiltration dynamics in single bundles is essential to process design and modeling efforts. Deposition of pyrolytic carbon in carbon-fiber bundles is chosen as the experimental system, with densification data obtained from thermogravimetric analysis. Data are then compared to predictions from a recently proposed CVI model for fiber bundle densification. 10 refs., 5 figs., 1 tab.

  10. Push rod for moving mine cars

    Energy Technology Data Exchange (ETDEWEB)

    Shtokman, I.G.; Apukhtin, A.S.; Dudnik, M.Z.; Remizov, I.P.; Shakhtar, P.S.


    In the operation of the known pushrods for haulage of cars on horizontal shafts, it becomes necessary to slow down the moving cars. In normal working modes, braking of the cars is guaranteed by counter engagement of the linear motors. However when emergency situations develop, for example if there is some lack of voltage in the network, it becomes necessary to brake the cars which this device cannot guarantee. The purpose of the invention is to brake the cars with disconnection of power. The goal is achieved because the push rod containing a frame with inductors attached to it installed on the sides of the rail path opposite each other, in which the cabs of the cars fill the role of the rotor, the support stands are connected to the inductors by means of springs, and the frame with inductors is hinged to the support stand and has mechanism for regulating the gap between the inductors and the cars, made in the form of rollers attached to the frame for interaction with the outer sidewalls of the car is equipped with friction elements installed on the frame and electromagnets with spring-rods installed on the support stands arranged with the possibility of interacting with the frame, and each friction element is arranged with the possibility of interacting with the rollers.

  11. Principal G-bundles on nodal curves

    Indian Academy of Sciences (India)

    Springer Verlag Heidelberg #4 2048 1996 Dec 15 10:16:45

    If Y is reducible these notions depend on parameters a = (a1,...,aI ). The study of G-bundles on Y is done by extending the notion of (generalized) parabolic vector bundles [U1] to generalized parabolic principal G-bundles (called GPGs in short) on the curve C and using the correspondence between them and principal ...

  12. Strategic and welfare implications of bundling

    DEFF Research Database (Denmark)

    Martin, Stephen


    A standard oligopoly model of bundling shows that bundling by a firm with a monopoly over one product has a strategic effect because it changes the substitution relationships between the goods among which consumers choose. Bundling in appropriate proportions is privately profitable, reduces rivals...

  13. The Atiyah bundle and connections on a principal bundle

    Indian Academy of Sciences (India)

    INDRANIL BISWAS. School of Mathematics, Tata Institute of Fundamental Research, Homi Bhabha Road,. Mumbai 400 005 .... (U) on A(EG)(U) and (U, g ⊕ Rd) defined by multiplication. Therefore, the sheaf A(EG) is locally free over FC∞. (M) of rank dim(g ⊕ Rd). Hence. A(EG) defines a C. ∞ vector bundle over M of rank ...

  14. Higher order jet prolongations type gauge natural bundles over vector bundles

    Directory of Open Access Journals (Sweden)

    Jan Kurek


    Full Text Available Let $rgeq 3$ and $mgeq 2$ be natural numbers and $E$ be a vector bundle with $m$-dimensional basis. We find all gauge natural bundles ``similar" to the $r$-jet prolongation bundle $J^rE$ of $E$. We also find all gauge natural bundles ``similar" to the vector $r$-tangent bundle $(J^r_{fl}(E,R_0^*$ of $E$.

  15. Experimental Study of Hydraulic Control Rod Drive Mechanism for Passive IN-core Cooling System of Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, In Guk; Kim, Kyung Mo; Jeong, Yeong Shin; Bang, In Cheol [KAERI, Daejeon (Korea, Republic of)


    CAREM 25 (27 MWe safety systems using hydraulic control rod drives (CRD) studied critical issues that were rod drops with interrupted flow [3]. Hydraulic control rod drive suggested fast shutdown condition using a large gap between piston and cylinder in order to fast drop of neutron absorbing rods. A Passive IN-core Cooling system (PINCs) was suggested for safety enhancement of pressurized water reactors (PWR), small modular reactor (SMR), sodium fast reactor (SFR) in UNIST. PINCs consist of hydraulic control rod drive mechanism (Hydraulic CRDM) and hybrid control rod assembly with heat pipe combined with control rod. The schematic diagram of the hydraulic CRDM for PINCs is shown in Fig. 1. The experimental results show the steady state and transient behavior of the upper cylinder at a low pressure and low temperature. The influence of the working fluid temperature and cylinder mass are investigated. Finally, the heat removal between evaporator section and condenser section is compared with or without the hybrid control rod. Heat removal test of the hybrid heat pipe with hydraulic CRDM system showed the heat transfer coefficient of the bundle hybrid control rod and its effect on evaporator pool. The preliminary test both hydraulic CRDM and heat removal system was conducted, which showed the possibility of the in-core hydraulic drive system for application of PINCs.

  16. Multipath packet switch using packet bundling

    DEFF Research Database (Denmark)

    Berger, Michael Stubert


    The basic concept of packet bundling is to group smaller packets into larger packets based on, e.g., quality of service or destination within the packet switch. This paper presents novel applications of bundling in packet switching. The larger packets created by bundling are utilized to extend...... switching capacity by use of parallel switch planes. During the bundling operation, packets will experience a delay that depends on the actual implementation of the bundling and scheduling scheme. Analytical results for delay bounds and buffer size requirements are presented for a specific scheduling...

  17. Literature search on Light Water Reactor (LWR) fuel and absorber rod fabrication, 1960--1976

    Energy Technology Data Exchange (ETDEWEB)

    Sample, C R [comp.


    A literature search was conducted to provide information supporting the design of a conceptual Light Water Reactor (LWR) Fuel Fabrication plant. Emphasis was placed on fuel processing and pin bundle fabrication, effects of fuel impurities and microstructure on performance and densification, quality assurance, absorber and poison rod fabrication, and fuel pin welding. All data have been taken from publicly available documents, journals, and books. This work was sponsored by the Finishing Processes-Mixed Oxide (MOX) Fuel Fabrication Studies program at HEDL.

  18. Actin-ADF/cofilin rod formation in Caenorhabditis elegans muscle requires a putative F-actin binding site of ADF/cofilin at the C-terminus. (United States)

    Ono, Kanako; Ono, Shoichiro


    Under a number of stress or pathological conditions, actin and actin depolymerizing factor (ADF)/cofilin form rod-like structures that contain abnormal bundles of actin filaments that are heavily decorated with ADF/cofilin. However, the mechanism of actin rod formation and the physiological role of actin rods are not clearly understood. Here, we report that overexpression of green fluorescent protein-fused UNC-60B, a muscle-specific ADF/cofilin isoform, in Caenorhabditis elegans body wall muscle induces formation of rod-like structures. The rods contained GFP-UNC-60B, actin-interacting protein 1 (AIP1), and actin, but not other major actin-associated proteins, thus resembling actin-ADF/cofilin rods found in other organisms. However, depletion or overexpression of AIP1 did not affect formation of the actin-GFP-UNC-60B rods, suggesting that AIP1 does not play a significant role in the rod assembly. Truncation of the C-terminal tail, a putative F-actin binding site, of UNC-60B abolished induction of the rod formation, strongly suggesting that stable association of UNC-60B with F-actin, which is mediated by its C-terminus, is required for inducing actin-ADF/cofilin rods. This study suggests that C. elegans can be a new model to study functions of actin-ADF/cofilin rods. (c) 2009 Wiley-Liss, Inc.

  19. Deconstructing the infection control bundles for the containment of carbapenem-resistant Enterobacteriaceae. (United States)

    Munoz-Price, L Silvia; Quinn, John P


    Rates of carbapenem-resistant Enterobacteriaceae (CRE), especially Klebsiella pneumoniae carbapenemase (KPC)-producing Gram-negatives, have increased worldwide. Infections caused by these organisms have been associated with a high mortality, which might be due in part to the limited availability of antibiotic options. Therefore, prevention of acquisition of these organisms is essential. This review summarizes published infection control interventions (bundles) that have been implemented for the control of outbreaks caused by KPC-producing organisms. A total of 15 bundles of interventions aimed at controlling CRE outbreaks are presented. The interventions included combinations of increased compliance with hand hygiene and contact precautions, environmental cleaning, early identification of asymptomatic carriers, and physical separation of CRE-positive patients and their staff. Three bundles had staggered implementation of interventions with their later phase involving a combination of rectal surveillance cultures for identification of asymptomatic CRE carriers, cohorting of CRE-positive patients, and cohorting of the staff caring for CRE carriers. All three staggered bundles successfully decreased their CRE acquisition rates after implementation of their later phases. Bundles combine multiple interventions targeting different levels of the transmission pathways and most include increased hand hygiene and contact precautions. However, bundles implemented in phases would seem to indicate that active surveillance cultures and the subsequent cohorting of patients and staff based on these results might be particularly beneficial for controlling horizontal transmission.

  20. The Third ATLAS ROD Workshop

    CERN Multimedia

    Poggioli, L.

    A new-style Workshop After two successful ATLAS ROD Workshops dedicated to the ROD hardware and held at the Geneva University in 1998 and in 2000, a new style Workshop took place at LAPP in Annecy on November 14-15, 2002. This time the Workshop was fully dedicated to the ROD-TDAQ integration and software in view of the near future integration activities of the final RODs for the detector assembly and commissioning. More precisely, the aim of this workshop was to get from the sub-detectors the parameters needed for T-DAQ, as well as status and plans from ROD builders. On the other hand, what was decided and assumed had to be stated (like EB decisions and URDs), and also support plans. The Workshop gathered about 70 participants from all ATLAS sub-detectors and the T-DAQ community. The quite dense agenda allowed nevertheless for many lively discussions, and for a dinner in the old town of Annecy. The Sessions The Workshop was organized in five main sessions: Assumptions and recommendations Sub-de...

  1. Static stress analysis of CANFLEX fuel bundles

    Energy Technology Data Exchange (ETDEWEB)

    Suk, Ho Chun; Kang, Hee Young; Sim, Ki Seop; Jeong, Jang Hwan; Jun, Gi Su; Park, Ju Hwan; Lee, Che Han; Kim, Tae Hyoung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)


    The static stress analysis of CANFLEX bundles is performed to evaluate the fuel structural integrity during the refuelling service. The structure analysis is carried out by predicting the drag force, stress and displacements of the fuel bundle. By the comparison of strength tests and analysis results, the displacement values are well agreed within 15%. The analysis shows that the CANFLEX fuel bundle keep its structural integrity. 24 figs., 6 tabs., 12 refs. (Author) .new.

  2. Ulrich Schur bundles on flag varieties


    Coskun, Izzet; Costa, Laura; Huizenga, Jack; Miró-Roig, Rosa Maria; Woolf, Matthew


    In this paper, we study equivariant vector bundles on partial flag varieties arising from Schur functors. We show that a partial flag variety with three or more steps does not admit an Ulrich bundle of this form with respect to the minimal ample class. We classify Ulrich bundles of this form on two-step flag varieties F(1,n-1;n), F(2,n-1;n), F(2,n-2;n), F(k,k+1;n) and F(k,k+2;n). We give a conjectural description of the two-step flag varieties which admit such Ulrich bundles.

  3. Equivariant Ulrich bundles on flag varieties


    Coskun, Izzet; Huizenga, Jack; Woolf, Matthew


    In this paper, we study equivariant vector bundles on partial flag varieties arising from Schur functors. We show that a partial flag variety with three or more steps does not admit an Ulrich bundle of this form with respect to the minimal ample class. We classify Ulrich bundles of this form on two-step flag varieties F(2,n;n+1), F(2,n;n+2), F(k,k+1;n), and F(k,k+2;n). We give a conjectural description of the two-step flag varieties which admit such Ulrich bundles. Our results provide counter...

  4. Axis deviation without left bundle branch block. (United States)

    Patanè, Salvatore; Marte, Filippo; Mancuso, Antonia


    It has been rarely reported changing axis deviation in the presence of left bundle branch block also during atrial fibrillation and with acute myocardial infarction too. It has also been rarely reported changing axis deviation with changing bundle branch block with onset of atrial fibrillation during acute myocardial infarction. We present a case of axis deviation without left bundle branch block and without atrial fibrillation and acute myocardial infarction in a 65-year-old Italian man. To our knowledge, this is the first report of axis deviation without left bundle branch block and without atrial fibrillation and acute myocardial infarction. Copyright 2008 Elsevier Ireland Ltd. All rights reserved.

  5. Advanced gray rod control assembly (United States)

    Drudy, Keith J; Carlson, William R; Conner, Michael E; Goldenfield, Mark; Hone, Michael J; Long, Jr., Carroll J; Parkinson, Jerod; Pomirleanu, Radu O


    An advanced gray rod control assembly (GRCA) for a nuclear reactor. The GRCA provides controlled insertion of gray rod assemblies into the reactor, thereby controlling the rate of power produced by the reactor and providing reactivity control at full power. Each gray rod assembly includes an elongated tubular member, a primary neutron-absorber disposed within the tubular member said neutron-absorber comprising an absorber material, preferably tungsten, having a 2200 m/s neutron absorption microscopic capture cross-section of from 10 to 30 barns. An internal support tube can be positioned between the primary absorber and the tubular member as a secondary absorber to enhance neutron absorption, absorber depletion, assembly weight, and assembly heat transfer characteristics.

  6. Electrostatic Deformation of Liquid Surfaces by a Charged Rod and a Van De Graaff Generator (United States)

    Slisko, Josip; García-Molina, Rafael; Abril, Isabel


    Authors of physics textbooks frequently use the deflection of a thin, vertically falling water jet by a charged balloon, comb, or rod as a visually appealing and conceptually relevant example of electrostatic attraction. Nevertheless, no attempts are made to explore whether these charged bodies could cause visible deformation of a horizontal water…

  7. Development of burnup dependent fuel rod model in COBRA-TF (United States)

    Yilmaz, Mine Ozdemir

    The purpose of this research was to develop a burnup dependent fuel thermal conductivity model within Pennsylvania State University, Reactor Dynamics and Fuel Management Group (RDFMG) version of the subchannel thermal-hydraulics code COBRA-TF (CTF). The model takes into account first, the degradation of fuel thermal conductivity with high burnup; and second, the fuel thermal conductivity dependence on the Gadolinium content for both UO2 and MOX fuel rods. The modified Nuclear Fuel Industries (NFI) model for UO2 fuel rods and Duriez/Modified NFI Model for MOX fuel rods were incorporated into CTF and fuel centerline predictions were compared against Halden experimental test data and FRAPCON-3.4 predictions to validate the burnup dependent fuel thermal conductivity model in CTF. Experimental test cases from Halden reactor fuel rods for UO2 fuel rods at Beginning of Life (BOL), through lifetime without Gd2O3 and through lifetime with Gd 2O3 and a MOX fuel rod were simulated with CTF. Since test fuel rod and FRAPCON-3.4 results were based on single rod measurements, CTF was run for a single fuel rod surrounded with a single channel configuration. Input decks for CTF were developed for one fuel rod located at the center of a subchannel (rod-centered subchannel approach). Fuel centerline temperatures predicted by CTF were compared against the measurements from Halden experimental test data and the predictions from FRAPCON-3.4. After implementing the new fuel thermal conductivity model in CTF and validating the model with experimental data, CTF model was applied to steady state and transient calculations. 4x4 PWR fuel bundle configuration from Purdue MOX benchmark was used to apply the new model for steady state and transient calculations. First, one of each high burnup UO2 and MOX fuel rods from 4x4 matrix were selected to carry out single fuel rod calculations and fuel centerline temperatures predicted by CTF/TORT-TD were compared against CTF /TORT-TD /FRAPTRAN

  8. Calculation of Heat-Bearing Agent’s Steady Flow in Fuel Bundle (United States)

    Amosova, E. V.; Guba, G. G.


    This paper introduces the result of studying the heat exchange in the fuel bundle of the nuclear reactor’s fuel magazine. The article considers the fuel bundle of the infinite number of fuel elements, fuel elements are considered in the checkerboard fashion (at the tops of a regular triangle a fuel element is a plain round rod. The inhomogeneity of volume energy release in the rod forms the inhomogeneity of temperature and velocity fields, and pressure. Computational methods for studying hydrodynamics in magazines and cores with rod-shape fuel elements are based on a significant simplification of the problem: using basic (averaged) equations, isobaric section hypothesis, porous body model, etc. This could be explained by the complexity of math description of the three-dimensional fluid flow in the multi-connected area with the transfer coefficient anisotropy, curved boundaries and technical computation difficulties. Thus, calculative studying suggests itself as promising and important. There was developed a method for calculating the heat-mass exchange processes of inter-channel fuel element motions, which allows considering the contribution of natural convection to the heat-mass exchange based on the Navier-Stokes equations and Boussinesq approximation.

  9. Temperature Distributions in LMR Fuel Pin Bundles as Modeled by COBRA-IV-I (United States)

    Wright, Steven A.; Stout, Sherry


    Most pin type reactor designs for space power or terrestrial applications group the fuel pins into a number of relatively large fuel pin bundles or subassemblies. Fuel bundles for terrestrial liquid metal fast breeders reactors typically use 217 - 271 pins per sub-assembly, while some SP100 designs use up to 331 pins in a central subassembly that was surrounded by partial assemblies. Because thermal creep is exponentially related to temperature, small changes in fuel pin cladding temperature can make large differences in the lifetime in a high temperature liquid metal reactor (LMR). This paper uses the COBRA-IV-I computer code to determine the temperature distribution within LMR fuel bundles. COBRA-IV-I uses the sub-channel analysis approach to determine the enthalpy (or temperature) and flow distribution in rod bundles for both steady-state and transient conditions. The COBRA code runs in only a few seconds and has been benchmarked and tested extensively over a wide range of flow conditions. In this report the flow and temperature distributions for two types of lithium cooled space reactor core designs were calculated. One design uses a very tight fuel pin packing that has a pitch to diameter ratio of 1.05 (small wire wrap with a diameter of 392 μm) as proposed in SP100. The other design uses a larger pitch to diameter ratio of 1.09 with a larger more conventional sized wire wrap diameter of 1 mm. The results of the COBRA pin bundle calculations show that the larger pitch-to-diameter fuel bundle designs are more tolerant to local flow blockages, and in addition they are less sensitive to mal-flow distributions that occur near the edges of the subassembly.

  10. SUBCHANFLOW: a thermal hydraulic sub-channel program to analyse fuel rod bundles and reactor cores

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez, V.; Imke, U.; Ivanov, A. [Karlsruhe Institute of Technology, Institute of Neutron Physics and Reactor Technology, Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Gomez, R., E-mail: Victor.Sanchez@kit.ed [University of Applied Sciences Offenburg, Badstr. 24, 77652 Offenburg (Germany)


    The improvement of numerical analysis tools for the design and safety evaluation of reactor cores in a continuous effort in the nuclear community not only to improve the plant efficiency but also to demonstrate high degree of safety. Investigations at the Institute of Neutron Physics and Reactor Technology of the Karlsruhe Institute of Technology (KIT) are focused on the further development and qualification of subchannel and system codes using experimental data. The majority of sub-channel codes in use likes Thesis, Bacchus, Cobra and Matra, were developed in the seventies and eighties. The programming style is rather obsolete and most of these codes are working internally with British Units instead of Si-Units. In the case of water, outdated steam tables are used. Both the trends to improve the efficiency of light water reactors (LWR) and the involvement of KIT in European projects related to the study of the technical feasibility of different fast reactors systems reinforced the need for the development and improvement of sub-channel codes, since they will play a key role in performing better designs as stand-alone tools or coupled to neutron physical codes (deterministic or stochastic). Hence, KIT started the development of a new sub-channel code SUBCHANFLOW based on the Cobra-family. SUBCHANFLOW is a modular code programmed in Fortran-95 with dynamic memory allocation using Si-units. Different fluids like liquid metals and water are available as coolant. In addition some models were improved or replaced by new ones. In this paper the structure, the physical models and the current validation status will be presented and discussed. (Author)

  11. Control rods in LMFBRs: a physics assessment

    Energy Technology Data Exchange (ETDEWEB)

    McFarlane, H.F.; Collins, P.J.


    This physics assessment is based on roughly 300 control rod worth measurements in ZPPR from 1972 to 1981. All ZPPR assemblies simulated mixed-oxide LMFBRs, representing sizes of 350, 700, and 900 MWe. Control rod worth measurements included single rods, various combinations of rods, and Ta and Eu rods. Additional measurements studied variations in B/sub 4/C enrichment, rod interaction effects, variations in rod geometry, neutron streaming in sodium-filled channels, and axial worth profiles. Analyses were done with design-equivalent methods, using ENDF/B Version IV data. Some computations for the sensitivities to approximations in the methods have been included. Comparisons of these analyses with the experiments have allowed the status of control rod physics in the US to be clearly defined.

  12. Heat transfer on HLM cooled wire-spaced fuel pin bundle simulator in the NACIE-UP facility

    Energy Technology Data Exchange (ETDEWEB)

    Di Piazza, Ivan, E-mail: [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, C.R. ENEA Brasimone, Camugnano (Italy); Angelucci, Morena; Marinari, Ranieri [University of Pisa, Dipartimento di Ingegneria Civile e Industriale, Pisa (Italy); Tarantino, Mariano [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, C.R. ENEA Brasimone, Camugnano (Italy); Forgione, Nicola [University of Pisa, Dipartimento di Ingegneria Civile e Industriale, Pisa (Italy)


    Highlights: • Experiments with a wire-wrapped 19-pin fuel bundle cooled by LBE. • Wall and bulk temperature measurements at three axial positions. • Heat transfer and error analysis in the range of low mass flow rates and Péclet number. • Comparison of local and section-averaged Nusselt number with correlations. - Abstract: The NACIE-UP experimental facility at the ENEA Brasimone Research Centre (Italy) allowed to evaluate the heat transfer coefficient of a wire-spaced fuel bundle cooled by lead-bismuth eutectic (LBE). Lead or lead-bismuth eutectic are very attractive as coolants for the GEN-IV fast reactors due to the good thermo-physical properties and the capability to fulfil the GEN-IV goals. Nevertheless, few experimental data on heat transfer with heavy liquid metals (HLM) are available in literature. Furthermore, just a few data can be identified on the specific topic of wire-spaced fuel bundle cooled by HLM. Additional analysis on thermo-fluid dynamic behaviour of the HLM inside the subchannels of a rod bundle is necessary to support the design and safety assessment of GEN. IV/ADS reactors. In this context, a wire-spaced 19-pin fuel bundle was installed inside the NACIE-UP facility. The pin bundle is equipped with 67 thermocouples to monitor temperatures and analyse the heat transfer behaviour in different sub-channels and axial positions. The experimental campaign was part of the SEARCH FP7 EU project to support the development of the MYRRHA irradiation facility (SCK-CEN). Natural and mixed circulation flow regimes were investigated, with subchannel Reynolds number in the range Re = 1000–10,000 and heat flux in the range q″ = 50–500 kW/m{sup 2}. Local Nusselt numbers were calculated for five sub-channels in different ranks at three axial positions. Section-averaged Nusselt number was also defined and calculated. Local Nusselt data showed good consistency with some of the correlation existing in literature for heat transfer in liquid metals

  13. Rod and lamellar growth of eutectic

    Directory of Open Access Journals (Sweden)

    M. Trepczyńska-Łent


    Full Text Available The paper presents adaptation problem of lamellar growth of eutectic. The formation of rod eutectic microstructure was investigated systematically. A new rod eutectic configuration was observed in which the rods form with elliptical cylindrical shape. A new interpretation of the eutectic growth theory was proposed.

  14. Solitary waves on nonlinear elastic rods. II

    DEFF Research Database (Denmark)

    Sørensen, Mads Peter; Christiansen, Peter Leth; Lomdahl, P. S.


    In continuation of an earlier study of propagation of solitary waves on nonlinear elastic rods, numerical investigations of blowup, reflection, and fission at continuous and discontinuous variation of the cross section for the rod and reflection at the end of the rod are presented. The results...

  15. Numerical Simulations on the Laser Spot Welding of Zirconium Alloy Endplate for Nuclear Fuel Bundle Assembly (United States)

    Satyanarayana, G.; Narayana, K. L.; Boggarapu, Nageswara Rao


    In the nuclear industry, a critical welding process is joining of an end plate to a fuel rod to form a fuel bundle. Literature on zirconium welding in such a critical operation is limited. A CFD model is developed and performed for the three-dimensional non-linear thermo-fluid analysis incorporating buoyancy and Marnangoni stress and specifying temperature dependent properties to predict weld geometry and temperature field in and around the melt pool of laser spot during welding of a zirconium alloy E110 endplate with a fuel rod. Using this method, it is possible to estimate the weld pool dimensions for the specified laser power and laser-on-time. The temperature profiles will estimate the HAZ and microstructure. The adequacy of generic nature of the model is validated with existing experimental data.

  16. Exploiting rod technology. Final report

    Energy Technology Data Exchange (ETDEWEB)



    ROD development was proceeding apace until recent budgetary decisions caused funding support for ROD development to be drastically reduced. The funding which was originally provided by DARPA and the Balanced Technology Initiative (BTI) Office has been cut back to zero from $800K. To determine the aeroballistic coefficients of a candidate dart, ARDEC is currently supporting development out of its own 6.2 funds at about $100K. ARDEC has made slow progress toward achieving this end because of failures in the original dart during testing. It appears that the next dart design to be tested will diverge from the original concept visualized by DARPA and Science and Technology Associates (STA). STA, the design engineer, takes exception to these changes on the basis of inappropriate test conditions and insufficient testing. At this time, the full resolution of this issue will be difficult because of the current management structure, which separates the developer (ARDEC) from the designer (STA).

  17. Fuel rod assembly to manifold attachment (United States)

    Donck, Harry A.; Veca, Anthony R.; Snyder, Jr., Harold J.


    A fuel element is formed with a plurality of fuel rod assemblies detachably connected to an overhead support with each of the fuel rod assemblies having a gas tight seal with the support to allow internal fission gaseous products to flow without leakage from the fuel rod assemblies into a vent manifold passageway system on the support. The upper ends of the fuel rod assemblies are located at vertically extending openings in the support and upper threaded members are threaded to the fuel rod assemblies to connect the latter to the support. The preferred threaded members are cap nuts having a dome wall encircling an upper threaded end on the fuel rod assembly and having an upper sealing surface for sealing contact with the support. Another and lower seal is achieved by abutting a sealing surface on each fuel rod assembly with the support. A deformable portion on the cap nut locks the latter against inadvertent turning off the fuel rod assembly. Orienting means on the fuel rod and support primarily locates the fuel rods azimuthally for reception of a deforming tool for the cap nut. A cross port in the fuel rod end plug discharges into a sealed annulus within the support, which serves as a circumferential chamber, connecting the manifold gas passageways in the support.

  18. A procedure for addressing the fuel rod failures during LB-LOCA transient in Atucha-2 NPP

    Energy Technology Data Exchange (ETDEWEB)

    Adorni, Martina; Del Nevo, Alessandro; Parisi, Carlo; D' Auria, Francesco [University of Pisa, San Piero a Grado Nuclear Research Group (GRNSPG), Via Diotisalvi 2, 56122 Pisa (Italy); Mazzantini, Oscar [Nucleoelectrica Argentina S.A., UGCNAII, 2806 Lima (Argentina)


    Overview of CNA-2 NPP: Atucha-2 is a pressurized heavy water cooled and moderated reactor (PHWR) designed by Siemens under construction in the Republic of Argentina. The nominal electric power is 745 MWe. The reactor is equipped with a PWR-type Reactor Pressure Vessel (RPV). The operating pressure for the moderator and the coolant is equal (11.5 MPa) since the same fluid is simultaneously passing through the core and the moderator tank. The moderator and coolant circuits are connected through the bypass in the lower plenum and the upper plenum of the RPV. The former is constituted by two loops with a U-Tubes SGs. The latter is a four loops moderator system connecting upstream and downstream the moderator tank. Four horizontal U-Tubes exchangers remove the heat from the moderator system and preheat the feed water. The reactor power is generated in the core, composed by 451 fuel bundles placed in vertical fuel channels, each one containing a fuel assembly (FA) composed by 37 fuel rods. The reactor power is removed via the above mentioned 2 hydraulic loops equipped with U-Tubes Steam Generators (SG). The fuel rod consists of a stack of natural UO{sub 2} pellets, of compensation pellets in Al{sub 2}O{sub 3}, the supporting tube, and the compression spring. Everything is placed into a Zircaloy-4 cladding tube. Although most fission products are retained within the UO{sub 2}, a fraction of the gaseous fission products is released from the pellets and accumulated in the plenum of the rod. The fuel rod cladding thickness is adequate to be 'free-standing', i.e., capable of withstanding external reactor pressure without collapsing onto the pellets. All fuel rods are internally pre-pressurized in order to reduce compressive clad stresses and creep down due to the high coolant pressure. Helium is used as pressurizing gas to get good heat transfer from fuel to cladding. The plant is operated with a on-power re-fueling that is performed by a refueling machine. After

  19. Einstein metrics on tangent bundles of spheres

    Energy Technology Data Exchange (ETDEWEB)

    Dancer, Andrew S [Jesus College, Oxford University, Oxford OX1 3DW (United Kingdom); Strachan, Ian A B [Department of Mathematics, University of Hull, Hull HU6 7RX (United Kingdom)


    We give an elementary treatment of the existence of complete Kaehler-Einstein metrics with nonpositive Einstein constant and underlying manifold diffeomorphic to the tangent bundle of the (n+1)-sphere.

  20. Dynamic bi-product bundle pricing problem

    Directory of Open Access Journals (Sweden)

    Rafiei Hamed


    Full Text Available This paper addresses bundle pricing problem of two products in a stochastic environment so as to maximize net profit of a retailer. In the considered problem, it is assumed that customers are received upon a Poisson distribution and their demands follow a bi-variant distribution function. Also, it is assumed that products are sold individually or in the form of a bundle, which are offered from an initial stock of the products. To tackle the problem, a stochastic dynamic program is developed in which optimum values of the initial stock and order quantities of every planning period are determined. Moreover, prices of the individual products and their bundle are optimized. Also, the proposed dynamic program tackles bundling/ unbundling decisions taken in every planning period. A numerical example of a two planning period horizon is considered to validate the proposed model.

  1. Is It Complete Left Bundle Branch Block? Just Ablate the Right Bundle. (United States)

    Ali, Hussam; Lupo, Pierpaolo; Foresti, Sara; De Ambroggi, Guido; Epicoco, Gianluca; Fundaliotis, Angelica; Cappato, Riccardo


    Complete left bundle branch block (LBBB) is established according to standard electrocardiographic criteria. However, functional LBBB may be rate-dependent or can perpetuate during tachycardia due to repetitive concealed retrograde penetration of impulses through the contralateral bundle "linking phenomenon." In this brief article, we present two patients with basal complete LBBB in whom ablating the right bundle unmasked the actual antegrade conduction capabilities of the left bundle. These cases highlight intriguing overlap between electrophysiological concepts of complete block, linking, extremely slow, and concealed conduction. © 2016 Wiley Periodicals, Inc.

  2. Physiological mechanisms of QRS narrowing in bundle branch block patients undergoing permanent His bundle pacing. (United States)

    Teng, Alexandra E; Massoud, Louis; Ajijola, Olujimi A


    His bundle pacing is increasingly used to avoid chronic right ventricular pacing, and electrically resynchronize ventricular activation by narrowing or normalizing the QRS interval in left and right bundle branch block. The mechanisms by which this occurs remain poorly understood. In this review, the proposed mechanisms and evidence supporting them are discussed. Also discussed are aspects of mechanisms that are not completely supported by the evidence. We also review the differences and physiological bases for direct vs. indirect His bundle capture, and the physiological mechanisms for QRS narrowing vs. normalization following His bundle pacing. Copyright © 2016 Elsevier Inc. All rights reserved.

  3. Compact Hybrid Laser Rod and Laser System (United States)

    Busch, George E. (Inventor); Amzajerdian, Farzin (Inventor); Pierrottet, Diego F. (Inventor)


    A hybrid fiber rod includes a fiber core and inner and outer cladding layers. The core is doped with an active element. The inner cladding layer surrounds the core, and has a refractive index substantially equal to that of the core. The outer cladding layer surrounds the inner cladding layer, and has a refractive index less than that of the core and inner cladding layer. The core length is about 30 to 2000 times the core diameter. A hybrid fiber rod laser system includes an oscillator laser, modulating device, the rod, and pump laser diode(s) energizing the rod from opposite ends. The rod acts as a waveguide for pump radiation but allows for free-space propagation of laser radiation. The rod may be used in a laser resonator. The core length is less than about twice the Rayleigh range. Degradation from single-mode to multi-mode beam propagation is thus avoided.

  4. Biomechanics of the porcine triple bundle anterior cruciate ligament. (United States)

    Kato, Yuki; Ingham, Sheila J M; Linde-Rosen, Monica; Smolinski, Patrick; Horaguchi, Takashi; Fu, Freddie H


    Several species of animals are used as a model to study human anterior cruciate ligament (ACL) reconstruction. In many animals, three bundles were clearly discernible during dissection in the ACL. However, there are few reports about the biomechanical role of each bundle in the porcine knee. The purpose of this study is to investigate the role of each of the three bundles in the porcine knee, especially the intermediate bundle. Ten porcine knees were tested using a robotic/universal forcemoment sensor system. This system applied anterior loading of 89 N at 30 degrees, 60 degrees and 90 degrees of flexion, and a combined 7 Nm valgus and 4 Nm internal tibial torque at 30 degrees and 60 degrees of flexion before and after each bundle was selectively cut. The in situ force (N) for each bundle of the ACL was measured. Both intermediate (IM) bundle and postero-lateral (PL) bundle had significantly lower in situ force than the antero-medial (AM) bundle in anterior loading. The IM and PL bundles carried a larger proportion of the force under the torsional loads than the anterior loads. But IM bundle had a significant lower in situ force during the combined torque at 60 degrees of knee flexion, when compared intact ACL. In summary, IM bundle has a subordinate role to the AM and PL bundles. AM bundle is more dominant than IM and PL bundles. The porcine knee is a suitable model for ACL studies, especially for AP stability.

  5. Application of the porous medium heat transfer model of ICARE/CATHARE code against debris bed and 'bundle' experiments

    Energy Technology Data Exchange (ETDEWEB)

    Repetto, G. [CEA Cadarache, Institut de Radioprotection et de Surete Nucleaire, DPAM, 13 - Saint-Paul-lez-Durance (France); Ederli, St. [Ente per le Nuove Technologie, l' Energia e l' Ambiente (ENEA) (Italy)


    ICARE/CATHARE code is developed by the 'Institut de Radioprotection et de Surete Nucleaire' to simulate Nuclear Reactor behaviour during the course of a Loss of Cooling accident up to the core melting. The assessment of the heat transfer model in porous medium has been performed against experiments performed in ACRR (SNL-USA) and in Phebus reactors (at Cadarache - France). Calculation versus experiment results indicate a good agreement for the thermal behaviour. The heat transfers inside solid debris bed can be well predicted using the Imura-Yagi correlation to calculate the debris bed equivalent thermal conductivity in a wide range of particles size. In the case of 'Rod like geometry' calculations, the fuel rod assembly was modelled assuming several rings of fuel rods, with heat transfer including radiative phenomena using view factors between rods. An alternative modelling has been used considering the fuel rods as a porous medium with with pure UO{sub 2} spherical particles of 1 cm diameter and a total porosity representative of the fuel bundle inside a cylindrical shroud. With this approach (heat exchanges accounted for with the Imura-Yagi correlation), the radial gradient calculated in a small bundle was significantly increased, from a few degrees (with the previous modelling) to about 150/200 K at 2273 K. This modelling has been recently improved, to account for the heat transfer inside a fuel rod bundle, by a specific model based on an electrical analogy, considering the porous medium as a cluster of true cylinders. (authors)

  6. Stability of Picard bundle over moduli space of stable vector bundles ...

    Indian Academy of Sciences (India)

    Springer Verlag Heidelberg #4 2048 1996 Dec 15 10:16:45

    Stability of Picard bundle over moduli space of stable vector bundles of rank two over a curve. INDRANIL BISWAS and TOM ´AS L G ´OMEZ. School of Mathematics, Tata Institute of Fundamental Research, Homi Bhabha Road,. Mumbai 400 005, India. E-mail:; MS received 14 ...

  7. Stability of Picard bundle over moduli space of stable vector bundles ...

    Indian Academy of Sciences (India)

    Abstract. Answering a question of [BV] it is proved that the Picard bundle on the moduli space of stable vector bundles of rank two, on a Riemann surface of genus at least three, with fixed determinant of odd degree is stable.

  8. Heat transfer and visualization of falling film evaporation on a tube bundle

    Energy Technology Data Exchange (ETDEWEB)

    Christians, M.


    Horizontal falling film evaporators have the potential of displacing flooded evaporators in industry, due to advantages such as lower required refrigerant charge and lower pressure drop. However, there is a need to improve the understanding of falling film evaporation mechanisms to provide accurate thermal design methods. In this work, the existing LTCM falling film facility was utilized to perform falling film evaporation measurements on a single tube, a vertical row of horizontal tubes and a small tube bundle. Two enhanced boiling tubes, namely the Wolverine Turbo-B5 and the Wieland Gewa-B5, were tested using R-134a and R-236fa. The tests were carried out at a constant saturation temperature of T{sub sat} = 5 °C, liquid film Reynolds numbers ranging from 0 to 3000, and heat fluxes between 15 and 90 kW/m{sup 2} in pool boiling and falling film configurations. A visualization study was performed under adiabatic and diabatic conditions (in both single-array and bundle configurations) to study the flow. The physical phenomena governing the falling film evaporation process have been studied, and insight into their effects on the performance of tube bundles has been gained. Measurements of the local heat transfer coefficient were obtained and utilized to generate new prediction methods, including a method for predicting the onset-of-dryout film flow rate during falling film evaporation, local pool boiling and falling film heat transfer prediction methods and a falling film multiplier prediction method. (author)

  9. Belo Horizonte em recortes

    Directory of Open Access Journals (Sweden)

    Ivete Lara Camargos Walty


    Full Text Available A partir do conceito de rizoma de Deleuze e Guatari, faz-se uma montagem de trechos de textos literários sobre Belo Horizonte, intercalados com extratos do livro As cidades invisíveis, de Italo Calvino, como objetivo de se esboçar faces/retratos da cidade.

  10. Horizontal violence in Nursing

    Directory of Open Access Journals (Sweden)

    Tsimoulaki Evangelia


    Full Text Available One’s effort to clarify the definition of horizontal labour violence is of great importance, due to the variety of definitions that are mentioned in the worldwide scientific literature. Furthermore, the reference of multiple forms of such violence herein the nurse professional group is challenging, as well. Another fact of great importance is that, any form of professional violence (horizontal violence, horizontal mobbing in the work place environment can be possibly escalated and include even physical abuse (Bullying, besides the psychological and emotional impact for the victim. The definitions of Horizontal violence, Mobbing and Bullying, include a repeated negative behaviour emanating from at least one “predator” towards at least one “victim”, with work status differences and the existence or lack of physical abuse (Bullying. Horizontal violence is a hostile, aggressive and harmful behaviour which is either overt or concealed and is pointed from an individual to another individual of the same working rank and causes intense emotional pain at the victim. The manifestations vary from humiliating tasks assignment or the victim’s efforts undermining to clearly aggressive behaviors (criticism, intimidation, sarcasm etc.. The reason behind this phenomenon is multifactorial extended not only towards the working environment but also to the personal characteristics of the “predator” as well as the possible “victim”. The researchers emphasize the high incidence of the phenomenon, as well as the cost that is induced by the violent behaviors to both the health professionals and the hospital. Finally, they point out the paradox of the presence of violence inside a system that is designed to promote health.

  11. Extraction of rod-like objects from vehicle-borne LiDAR data (United States)

    Wu, Zhenzhen; Liu, Huiyun; Li, Kuangyu; Mao, Jie; Zhang, Xitong


    A rod-like objects extraction method based on clustering is presented. Firstly, project the original point clouds onto the horizontal plane, divide them into grids, and take a single grid as data processing unit to remove the ground points; Secondly, make the grid based on processing data for point clouds detection and numbered, give the same attribute values and cluster the object points using eight neighborhood search method. Then, take the clustered single point clouds as processing units, take advantage of various object features, such as height, density projection, the projection area and shape to exclude the other object points progressively, and achieve the fine extraction of the rod-like objects. The experiment tests the validity of the method described in the text of the extraction of the rod-like objects in road environment.

  12. The geometry of the tangent bundle and the relativistic kinetic theory of gases

    CERN Document Server

    Sarbach, Olivier


    This article discusses the relativistic kinetic theory for a simple collisionless gas from a geometric perspective. We start by reviewing the rich geometrical structure of the tangent bundle TM of a given spacetime manifold, including the splitting of the tangent spaces of TM into horizontal and vertical subspaces and the natural metric and symplectic structure it induces on TM. Based on these structures we introduce the Liouville vector field L and a suitable Hamiltonian function H on TM. The Liouville vector field turns out to be the Hamiltonian vector field associated to H. On the other hand, H also defines the mass shells as Lorentzian submanifolds of the tangent bundle. A simple collisionless gas is described by a distribution function on a particular mass shell, satisfying the Liouville equation. Together with the Liouville vector field the distribution function can be thought of as defining a fictitious incompressible fluid on the mass shells, with associated conserved current density. Finally, we disc...

  13. Tipping Time of a Quantum Rod (United States)

    Parrikar, Onkar


    The behaviour of a quantum rod, pivoted at its lower end on an impenetrable floor and restricted to moving in the vertical plane under the gravitational potential, is studied analytically under the approximation that the rod is initially localized to a "small-enough" neighbourhood around the point of classical unstable equilibrium. It is shown…

  14. Computing Temperatures In Optically Pumped Laser Rods (United States)

    Farrukh, Usamah O.


    Computer program presents new model solving temperature-distribution problem for laser rods of finite length and calculates both radial and axial components of temperature distributions in these rods. Contains several self-checking schemes to prevent over-writing of memory blocks and to provide simple tracing of information in case of trouble. Written in Microsoft FORTRAN 77.

  15. Self-contact for rods on cylinders

    NARCIS (Netherlands)

    G.H.M. van der Heijden; M.A. Peletier (Mark); R. Planqué (Robert)


    textabstractWe study self-contact phenomena in elastic rods that are constrained to lie on a cylinder. By choosing a particular set of variables to describe the rod centerline the variational setting is made particularly simple: the strain energy is a second-order functional of a single scalar

  16. Balance Ability and Proprioception after Single-Bundle, Single-Bundle Augmentation, and Double-Bundle ACL Reconstruction

    Directory of Open Access Journals (Sweden)

    Yubao Ma


    Full Text Available Purpose. The present study sought to determine the influences of single-bundle (SB, single-bundle augmentation (SBA, and double-bundle (DB reconstructions on balance ability and proprioceptive function. Methods. 67 patients who underwent a single- or double-bundle ACL reconstruction or a SBA using multistranded autologous hamstring tendons were included in this study with a 1-year follow-up. Body sway and knee kinesthesia (using the threshold to detect passive motion test (TTDPM were measured to indicate balance ability and proprioceptive function, respectively. Additionally, within-subject differences in anterior-posterior stability of the tibia and lower extremity muscle strength were evaluated before and after surgery. Results. At 6 and 12 months after surgery, DB reconstruction resulted in better balance and proprioceptive function than SB reconstruction (P<0.05. Although no significant difference was observed in balance ability or proprioceptive function between the SBA and DB reconstructions, knee stability was significantly better with SBA and DB reconstructions than SB reconstruction (P<0.05. No significant differences were found in quadriceps and hamstrings strength among the three reconstruction techniques. Conclusions. Our findings consider that joint stability, proprioceptive function, and balance ability were superior with SBA and DB reconstructions compared to SB reconstruction at 6 and 12 months after surgery.

  17. Horizontal drilling activity in Manitoba

    Energy Technology Data Exchange (ETDEWEB)

    Fox, J.


    An update of horizontal well drilling in Manitoba was provided. Manitoba`s productive formations are: (1) the Bakken Formation, (2) the Lodgepole Formation, (3) the Mission Canyon Formation, (4) the Amaranth Formation, and (5) the Melita Formation. A total of 28 exploratory wells and 29 development wells, including 11 horizontal wells were drilled in 1996. The 11 horizontal wells accounted for 30 per cent of the drilling meterage. The leading drillers for horizontal wells in Manitoba are Tundra Oil and Gas, Chevron, Anderson and HCO. Production from horizontal wells in 1996 totaled 310 cubic meter per day. To date, no horizontal wells have been drilled in the Bakken Formation. The least successful horizontal well application has been in the Lodgepole Formation. A summary of horizontal well production was provided for each Formation. 4 tabs., 10 figs.

  18. Graph Bundling by Kernel Density Estimation

    NARCIS (Netherlands)

    Hurter, C.; Ersoy, O.; Telea, A.

    We present a fast and simple method to compute bundled layouts of general graphs. For this, we first transform a given graph drawing into a density map using kernel density estimation. Next, we apply an image sharpening technique which progressively merges local height maxima by moving the convolved

  19. Permanent His-Bundle Pacing: Case Studies. (United States)

    Vijayaraman, Pugazhendhi; Dandamudi, Gopi


    His bundle pacing (HBP) is a physiological alternative to right ventricular pacing. In addition to patients with normal His-Purkinje conduction, HBP can be valuable in patients with infranodal atrioventricular (AV) block and patients undergoing AV node ablation. The following case studies illustrate the challenges associated with HBP. © 2016 Wiley Periodicals, Inc.

  20. Fluxes, bundle gerbes and 2-Hilbert spaces (United States)

    Bunk, Severin; Szabo, Richard J.


    We elaborate on the construction of a prequantum 2-Hilbert space from a bundle gerbe over a 2-plectic manifold, providing the first steps in a programme of higher geometric quantisation of closed strings in flux compactifications and of M5-branes in C-fields. We review in detail the construction of the 2-category of bundle gerbes and introduce the higher geometrical structures necessary to turn their categories of sections into 2-Hilbert spaces. We work out several explicit examples of 2-Hilbert spaces in the context of closed strings and M5-branes on flat space. We also work out the prequantum 2-Hilbert space associated with an M-theory lift of closed strings described by an asymmetric cyclic orbifold of the SU(2) WZW model, providing an example of sections of a torsion gerbe on a curved background. We describe the dimensional reduction of M-theory to string theory in these settings as a map from 2-isomorphism classes of sections of bundle gerbes to sections of corresponding line bundles, which is compatible with the respective monoidal structures and module actions.

  1. The unintended consequences of bundled payments. (United States)

    Weeks, William B; Rauh, Stephen S; Wadsworth, Eric B; Weinstein, James N


    Consensus is building that episode-based bundled payments can produce substantial Medicare savings, and the Center for Medicare & Medicaid Innovation's Bundled Payment Initiative endorses this concept. The program generates potential cost savings by reducing the historic cost of time-defined episodes of care, provided through a discount. Although bundled payments can reduce waste primarily in the postacute care setting, concerns arise that, in an effort to maintain income levels that are necessary to cover fixed costs, providers may change their behaviors to increase the volume of episodes. Such actions would mitigate the savings that Medicare might have accrued and may perpetuate the fee-for-service payment mechanism, with episodes of care becoming the new service. Although bundled payments have some advantages over the current reimbursement system, true cost-savings to Medicare will be realized only when the federal government addresses the use issue that underlies much of the waste inherent in the system and provides ample incentives to eliminate capacity and move toward capitation.

  2. Capacity efficiency of recovery request bundling

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Dittmann, Lars; Berger, Michael Stübert


    This paper presents a comparison of recovery methods in terms of capacity efficiency. In particular, a method where recovery requests are bundled towards the destination (Shortcut Span Protection) is evaluated against traditional recovery methods. Our simulation results show that Shortcut Span...

  3. Meromorphic connections on vector bundles over curves

    Indian Academy of Sciences (India)

    Descartes,. 67084 Strasbourg Cedex, France. *Correspond author. E-mail:; MS received 17 July 2013; revised 20 October 2013. Abstract. We give a criterion for filtered vector bundles over curves to admit a ...

  4. Anterior cruciate ligament reconstruction with double bundle versus single bundle: experimental study

    National Research Council Canada - National Science Library

    Roberto F. Mota e Albuquerque; Sandra Umeda Sasaki; Marco Martins Amatuzzi; Fabio Janson Angelini


    OBJECTIVE: To test an intra-articular reconstruction of the anterior cruciate ligament of the knee in 10 human cadavers by replacing 2 anterior cruciate ligament bundles, with the purpose of producing...

  5. Functional aspects of His bundle physiology and pathophysiology: Clinical implications. (United States)

    Scherlag, Benjamin J; Lazzara, Ralph

    In this review we present evidence from many experimental studies which challenge the concept of predestination of His bundle fibers. Using both intra- and extracellular His bundle pacing in the context of atrio-ventricular block and the development of bundle branch blocks these experimental studies provide the underlying mechanisms for the recent clinical findings showing the benefits of permanent His bundle pacing. Copyright © 2016 Elsevier Inc. All rights reserved.

  6. A case of 'Masquerading' bundle branch block: a forgotten concept. (United States)

    Choudhary, Dinesh; Namboodiri, Narayanan; Tharakan, Jaganmohan A


    'Masquerading' bundle branch block (right bundle branch block in the precordial leads with left bundle branch block in frontal leads and left axis deviation) is seen most commonly with coronary artery disease and hypertension. No definite explanation is available so far for these changes. We are presenting a case of rare congenital intranuclear inclusion myopathy with congestive heart failure and 'Masquerading' bundle branch block in ECG. Copyright © 2013 Cardiological Society of India. Published by Elsevier B.V. All rights reserved.

  7. Bundling revisited: substitute products and inter-firm discounts


    Armstrong, Mark


    This paper extends the standard model of bundling to allow products to be substitutes and for products to be supplied by separate sellers. Whether integrated or separate, firms have an incentive to introduce bundling discounts when demand for the bundle is elastic relative to demand for stand-alone products. When products are partial substitutes, this typically gives an integrated firm a greater incentive to offer a bundle discount (relative to the standard model with additive preferences), w...

  8. Estimation of irradiated control rod worth

    Energy Technology Data Exchange (ETDEWEB)

    Varvayanni, M., E-mail: melina@ipta.demokritos.g [NCSR ' DEMOKRITOS' , PO Box 60228, 15310 Aghia Paraskevi (Greece); Catsaros, N. [NCSR ' DEMOKRITOS' , PO Box 60228, 15310 Aghia Paraskevi (Greece); Antonopoulos-Domis, M. [School of Electrical and Computer Engineering, Aristotle University of Thessaloniki, Thessaloniki (Greece)


    When depleted control rods are planned to be used in new core configurations, their worth has to be accurately predicted in order to deduce key design and safety parameters such as the available shutdown margin. In this work a methodology is suggested for the derivation of the distributed absorbing capacity of a depleted rod, useful in the case that the level of detail that is known about the irradiation history of the control rod does not allow an accurate calculation of the absorber's burnup. The suggested methodology is based on measurements of the rod's worth carried out in the former core configuration and on corresponding calculations based on the original (before first irradiation) absorber concentration. The methodology is formulated for the general case of the multi-group theory; it is successfully tested for the one-group approximation, for a depleted control rod of the Greek Research Reactor, containing five neutron absorbers. The computations reproduce satisfactorily the irradiated rod worth measurements, practically eliminating the discrepancy of the total rod worth, compared to the computations based on the nominal absorber densities.

  9. Control Rod Malfunction at the NRAD Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Thomas L. Maddock


    The neutron Radiography Reactor (NRAD) is a training, research, and isotope (TRIGA) reactor located at the INL. The reactor is normally shut down by the insertion of three control rods that drop into the core when power is removed from electromagnets. During a routine shutdown, indicator lights on the console showed that one of the control rods was not inserted. It was initially thought that the indicator lights were in error because of a limit switch that was out of adjustment. Through further testing, it was determined that the control rod did not drop when the scram switch was initially pressed. The control rod anomaly led to a six month shutdown of the reactor and an in depth investigation of the reactor protective system. The investigation looked into: scram switch operation, console modifications, and control rod drive mechanisms. A number of latent issues were discovered and corrected during the investigation. The cause of the control rod malfunction was found to be a buildup of corrosion in the control rod drive mechanism. The investigation resulted in modifications to equipment, changes to both operation and maintenance procedures, and additional training. No reoccurrences of the problem have been observed since corrective actions were implemented.

  10. Magnetically controlled growing rods for scoliosis surgery. (United States)

    Metkar, Umesh; Kurra, Swamy; Quinzi, David; Albanese, Stephen; Lavelle, William F


    Early onset scoliosis can be both a disfiguring as well as a life threatening condition. When more conservative treatments fail, pediatric spinal surgeons are forced to consider operative interventions. Traditionally, these interventions have involved the insertion of a variety of implants into the patient with a limited number of anchor points controlling the spine. In the past, these pediatric patients have had multiple surgeries for elective lengthening of these devices to facilitate their growth while attempting to control the scoliosis. These patients often experience a physical and emotional toll from their multiple repeated surgeries. Growing spine techniques have also had a noted high complication rate due to implant dislodgement and infections. Recently, the development of non-invasively, self-lengthening growing rods has occurred. These devices have the potential to allow for the devices to be lengthened magnetically in a conscious patient in the surgeon's office. Areas covered: This review summarized previously published articles in the English literature using a key word search in PubMed for: 'magnetically controlled growing rods', 'Magec rods', 'magnetic growing rods' and 'growing rods'. Expert commentary: Magnetically controlled growing rods have an advantage over growing rods in lengthening the growing spine in the absence of repetitive surgeries.

  11. Induced Current Measurement of Rod Vibrations (United States)

    Sawicki, Charles A.


    The longitudinal normal modes of vibration of rods are similar to the modes seen in pipes open at both ends. A maximum of particle displacement exists at both ends and an integral number (n) of half wavelengths fit into the rod length. The frequencies fn of the normal modes is given by Eq. (1), where L is the rod length and V is the wave velocity: fn = nV/2L. Many methods have been used to measure the velocity of these waves. The Kundt's tube method commonly used in student labs will not be discussed here. A simpler related method has been described by Nicklin.2 Kluk3 measured velocities in a wide range of materials using a frequency counter and microphone to study sounds produced by impacts. Several earlier methods4,5 used phonograph cartridges complete with needles to detect vibrations in excited rods. A recent interesting experiment6 used wave-induced changes in magnetization produced in an iron rod by striking one end. The travel time, measured as the impulsive wave reflects back and forth, gave the wave velocity for the iron rod. In the method described here, a small magnet is attached to the rod with epoxy, and vibrations are detected using the current induced in a few loops of wire. The experiment is simple and yields very accurate velocity values.

  12. Compactifications of reductive groups as moduli stacks of bundles

    DEFF Research Database (Denmark)

    Martens, Johan; Thaddeus, Michael

    Let G be a reductive group. We introduce the moduli problem of "bundle chains" parametrizing framed principal G-bundles on chains of lines. Any fan supported in a Weyl chamber determines a stability condition on bundle chains. Its moduli stack provides an equivariant toroidal compactification of ...... studied by Losev-Manin....

  13. Turkish and Native English Academic Writers' Use of Lexical Bundles (United States)

    Öztürk, Yusuf; Köse, Gül Durmusoglu


    Lexical bundles such as "on the other hand" and "as a result of" are extremely common and important in academic discourse. The appropriate use of lexical bundles typical of a specific academic discipline is important for writers and the absence of such bundles may not sound fluent and native-like. Recent studies (e.g. Adel…

  14. Quillen bundle and geometric prequantization of non-abelian ...

    Indian Academy of Sciences (India)

    In this paper we prequantize the moduli space of non-abelian vortices. We explicitly calculate the symplectic form arising from 2 metric and we construct a prequantum line bundle whose curvature is proportional to this symplectic form. The prequantum line bundle turns out to be Quillen's determinant line bundle with a ...

  15. The Bundle of His in Prosthetic Heart Valve Replacement*

    African Journals Online (AJOL)


    Jan 27, 1973 ... ventricular seplUm which transected the bundle of His. Blocks were then fashioned backwards and forwards.. to include the whole of the bundle and the AV node. as well as the bifurcation of the bundle into its left and right branches. According to Davies: in order to study the whole conduction system in an ...

  16. Real parabolic vector bundles over a real curve

    Indian Academy of Sciences (India)

    weights are integral multiples of 1/N, and the category of real -equivariant vector bundles on (Y,σY ). ... The notion of parabolic vector bundles over a compact Riemann surface was introduced by Seshadri [4] and their .... stable. If F is a direct sum of stable vector bundles having the same slope, then F is called polystable.

  17. Geometry of torus bundles in integrable Hamiltonian systems

    NARCIS (Netherlands)

    Lukina, Olga


    Thesis is concerned with global properties of Lagrangian bundles, i.e. symplectic n-torus bundles, as these occur in integrable Hamiltonian systems. It treats obstructions to triviality and concerns with classification of such bundles, as well as with manifestations of global invariants in

  18. Masquerading bundle branch block: a variety of right bundle branch block with left anterior fascicular block. (United States)

    Elizari, Marcelo V; Baranchuk, Adrian; Chiale, Pablo A


    The so-called 'masquerading' type of right bundle branch block is caused by the simultaneous presence of a high-degree left anterior fascicular block often accompanied with severe left ventricular enlargement and/or fibrotic block in the anterolateral wall of the left ventricle. These conditions tend to reorient the terminal electrical forces of the QRS complex towards the left and upwards, in such a way that the characteristic slurred S wave in lead I becomes smaller or even disappears. In many cases of standard masquerading right bundle branch block, a small Q wave in lead I is present due to the initial forces of the left anterior fascicular block, which are oriented rightwards and inferiorly. However, in some cases, the Q wave in lead I also vanishes, and the mimicking of a left bundle branch block becomes perfect in standard leads. This is commonly associated with an inferior myocardial infarction or severe inferior fibrosis in cardiomyopathies. The typical QRS changes of right bundle branch block may eventually be concealed even in the right precordial leads; under such circumstances, the ECG diagnosis may be mistaken and the right bundle branch block totally missed. The masquerading right bundle branch block carries a poor prognosis, since it always implies the presence of a severe underlying heart disease.

  19. Bijels stabilized using rod-like particles. (United States)

    Hijnen, Niek; Cai, Dongyu; Clegg, Paul S


    Bicontinuous interfacially jammed emulsion gels, in short 'bijels', rely on a trapped layer of colloidal particles for their stability. These structures have traditionally been created using spherical colloidal particles. Here we show for the first time the use of rod-shape particles to stabilize bijels. We show that domain size decreases more rapidly with particle concentration in the case of rods compared to spheres. Large-scale analysis and detailed examination of images show that the packing fraction of rods is much higher than expected, in part, due to the role of 'flippers'.

  20. Bundling of harvesting residues and whole-trees and the treatment of bundles; Hakkuutaehteiden ja kokopuiden niputus ja nippujen kaesittely

    Energy Technology Data Exchange (ETDEWEB)

    Kaipainen, H.; Seppaenen, V.; Rinne, S.


    The conditions on which the bundling of the harvesting residues from spruce regeneration fellings would become profitable were studied. The calculations showed that one of the most important features was sufficient compaction of the bundle, so that the portion of the wood in the unit volume of the bundle has to be more than 40 %. The tests showed that the timber grab loader of farm tractor was insufficient for production of dense bundles. The feeding and compression device of the prototype bundler was constructed in the research and with this device the required density was obtained.The rate of compaction of the dry spruce felling residues was about 40 % and that of the fresh residues was more than 50 %. The comparison between the bundles showed that the calorific value of the fresh bundle per unit volume was nearly 30 % higher than that of the dry bundle. This means that the treatment of the bundles should be done of fresh felling residues. Drying of the bundles succeeded well, and the crushing and chipping tests showed that the processing of the bundles at the plant is possible. The treatability of the bundles was also excellent. By using the prototype, developed in the research, it was possible to produce a bundle of the fresh spruce harvesting residues, the diameter of which was about 50 cm and the length about 3 m, and the rate of compaction over 50 %. By these values the reduction target of the costs is obtainable

  1. The rod as an instrument of discipline


    Milton Luiz Torres; Centro Universitário Adventista de São Paulo, São Paulo, SP


    Both in biblical literature as in ancient extrabiblical literature, the use of the rod appears primarily related to the capacity or to the authority of the one who holds it. It is, above all, an instrument of power. This article investigates the implications of using the rod as a tool of correction and discipline, taking into account the symbolism, culture and literary tradition associated with the use of that instrument of discipline for correction and transformation of those subjected to it...

  2. High Power Performance of Rod Fiber Amplifiers

    DEFF Research Database (Denmark)

    Johansen, Mette Marie; Michieletto, Mattia; Kristensen, Torben


    An improved version of the DMF rod fiber is tested in a high power setup delivering 360W of stable signal power. Multiple testing degrades the fiber and transverse modal instability threshold from >360W to ~290W.......An improved version of the DMF rod fiber is tested in a high power setup delivering 360W of stable signal power. Multiple testing degrades the fiber and transverse modal instability threshold from >360W to ~290W....


    Directory of Open Access Journals (Sweden)

    Ulitin G.


    Full Text Available The problem is considered of longitudinal impact conical rod in article. A recommendation on the use of the approximate method of calculation is based on an analysis of the influence of design parameters on the value of the main oscillation frequency. There was obtained an equation of the displacement and stress of the rod. Engineering dependence has been proposed to determine the maximum force in the impact section.

  4. Microelectrophoresis of Silica Rods Using Confocal Microscopy (United States)


    The electrophoretic mobility and the zeta potential (ζ) of fluorescently labeled colloidal silica rods, with an aspect ratio of 3.8 and 6.1, were determined with microelectrophoresis measurements using confocal microscopy. In the case where the colloidal particles all move at the same speed parallel to the direction of the electric field, we record a xyz-stack over the whole depth of the capillary. This method is faster and more robust compared to taking xyt-series at different depths inside the capillary to obtain the parabolic flow profile, as was done in previous work from our group. In some cases, rodlike particles do not move all at the same speed in the electric field, but exhibit a velocity that depends on the angle between the long axis of the rod and the electric field. We measured the orientation-dependent velocity of individual silica rods during electrophoresis as a function of κa, where κ–1 is the double layer thickness and a is the radius of the rod associated with the diameter. Thus, we determined the anisotropic electrophoretic mobility of the silica rods with different sized double layers. The size of the double layer was tuned by suspending silica rods in different solvents at different electrolyte concentrations. We compared these results with theoretical predictions. We show that even at already relatively high κa when the Smoluchowski limiting law is assumed to be valid (κa > 10), an orientation dependent velocity was measured. Furthermore, we observed that at decreasing values of κa the anisotropy in the electrophoretic mobility of the rods increases. However, in low polar solvents with κa mobility of the rods decreased. We argue that this decrease is due to end effects, which was already predicted theoretically. When end effects are not taken into account, this will lead to strong underestimation of the experimentally determined zeta potential. PMID:28045541

  5. Baseline left bundle branch block with right bundle branch escape complexes in a patient with coronary artery disease, presents like an alternating bundle branch block: a case report (United States)

    Bhimaraj, Arvind; Abusin, Salaheldin; Margeta, Bosko


    Alternating bundle branch block (ABBB) is a less commonly encountered phenomenon with the advent of re-perfusion therapy for acute myocardial infarction. ECGs simulating the appearance of an ABBB need to be carefully analysed. We present an ECG showing a baseline Left Bundle Branch Block(LBBB) progressing to a high grade AV block with escape complexes having a Right Bundle Branch Block (RBBB) morphology. Such an ECG can be mistaken for an ABBB if not analysed carefully. PMID:19116014

  6. CFD analyses of the rod bowing effect on the subchannel outlet temperature distribution

    Energy Technology Data Exchange (ETDEWEB)

    Ekstroem, Karoliina; Toppila, Timo [Fortum Power and Heat, Fortum (Finland)


    In the Loviisa 1 and 2 nuclear power plants the subcooling margin of the hottest subchannel of the fuel assembly is monitored. The temperature of the coolant in the hottest subchannel is limited to the constant saturation temperature. Bending of the fuel rods occurs during normal operation due to the differences in the heat profiles of the rods. The coolant temperature will rise more in the subchannel with smaller flow area due to the bending and this has to be taken into account in the safety margin of subchannel enthalpy rise. Computational Fluid Dynamics (CFD) simulations are used to estimate how much the estimated maximum bow of a rod affects the temperature rise of the subchannel. The quantitative uncertainty of the predicted enthalpy rise in fuel bundle subchannel is estimated based on the uncertainty of modelling of mixing between subchannels. The measured turbulence quantities from LDA measurements of cold test assembly made in 1990s in Fortum are compared with CFD results to give uncertainty estimation for turbulence, which is further used for uncertainty estimation of mixing and simulated subchannel enthalpy rise.


    Treshow, M.


    Reactors of the boiling water type are described wherein water serves both as the moderator and coolant. The reactor system consists essentially of a horizontal pressure vessel divided into two compartments by a weir, a thermal neutronic reactor core having vertical coolant passages and designed to use water as a moderator-coolant posltioned in one compartment, means for removing live steam from the other compartment and means for conveying feed-water and water from the steam compartment to the reactor compartment. The system further includes auxiliary apparatus to utilize the steam for driving a turbine and returning the condensate to the feed-water inlet of the reactor. The entire system is designed so that the reactor is self-regulating and has self-limiting power and self-limiting pressure features.


    Directory of Open Access Journals (Sweden)

    Didi Junaedi


    implementation to Dekalb brand hybrid corn and Round-up brand herbicide. By analyzes how consumer attitudes toward buying intention in this regard farmers as buyer and retailers as products services. The data used is primary data. Primary data is obtained using 2 kind of respondents are retailers and farmers. The data obtained by distributed 30 questionnaires for retailers and 110 farmers in Grobogan. The descriptive statistic employed to analyzed data by using multiple linear regressions with t test, F test and coefficient of determination. The result showed that on retailers respondents attribute the product bundling has no significant influence to consumer buying intention but consumer attitudes significantly influence the buying intention. On the farmers respondents showed that attributes of the product bundling and consumer attitudes positive and significant influence to buying intention.

  9. Covariance and the hierarchy of frame bundles (United States)

    Estabrook, Frank B.


    This is an essay on the general concept of covariance, and its connection with the structure of the nested set of higher frame bundles over a differentiable manifold. Examples of covariant geometric objects include not only linear tensor fields, densities and forms, but affinity fields, sectors and sector forms, higher order frame fields, etc., often having nonlinear transformation rules and Lie derivatives. The intrinsic, or invariant, sets of forms that arise on frame bundles satisfy the graded Cartan-Maurer structure equations of an infinite Lie algebra. Reduction of these gives invariant structure equations for Lie pseudogroups, and for G-structures of various orders. Some new results are introduced for prolongation of structure equations, and for treatment of Riemannian geometry with higher-order moving frames. The use of invariant form equations for nonlinear field physics is implicitly advocated.

  10. Client Provider Collaboration for Service Bundling

    Directory of Open Access Journals (Sweden)

    LETIA, I. A.


    Full Text Available The key requirement for a service industry organization to reach competitive advantages through product diversification is the existence of a well defined method for building service bundles. Based on the idea that the quality of a service or its value is given by the difference between expectations and perceptions, we draw the main components of a frame that aims to support the client and the provider agent in an active collaboration meant to co-create service bundles. Following e3-value model, we structure the supporting knowledge around the relation between needs and satisfying services. We deal with different perspectives about quality through an ontological extension of Value Based Argumentation. The dialog between the client and the provider takes the form of a persuasion whose dynamic object is the current best configuration. Our approach for building service packages is a demand driven approach, allowing progressive disclosure of private knowledge.

  11. Uncovering Ecosystem Service Bundles through Social Preferences (United States)

    Martín-López, Berta; Iniesta-Arandia, Irene; García-Llorente, Marina; Palomo, Ignacio; Casado-Arzuaga, Izaskun; Amo, David García Del; Gómez-Baggethun, Erik; Oteros-Rozas, Elisa; Palacios-Agundez, Igone; Willaarts, Bárbara; González, José A.; Santos-Martín, Fernando; Onaindia, Miren; López-Santiago, Cesar; Montes, Carlos


    Ecosystem service assessments have increasingly been used to support environmental management policies, mainly based on biophysical and economic indicators. However, few studies have coped with the social-cultural dimension of ecosystem services, despite being considered a research priority. We examined how ecosystem service bundles and trade-offs emerge from diverging social preferences toward ecosystem services delivered by various types of ecosystems in Spain. We conducted 3,379 direct face-to-face questionnaires in eight different case study sites from 2007 to 2011. Overall, 90.5% of the sampled population recognized the ecosystem’s capacity to deliver services. Formal studies, environmental behavior, and gender variables influenced the probability of people recognizing the ecosystem’s capacity to provide services. The ecosystem services most frequently perceived by people were regulating services; of those, air purification held the greatest importance. However, statistical analysis showed that socio-cultural factors and the conservation management strategy of ecosystems (i.e., National Park, Natural Park, or a non-protected area) have an effect on social preferences toward ecosystem services. Ecosystem service trade-offs and bundles were identified by analyzing social preferences through multivariate analysis (redundancy analysis and hierarchical cluster analysis). We found a clear trade-off among provisioning services (and recreational hunting) versus regulating services and almost all cultural services. We identified three ecosystem service bundles associated with the conservation management strategy and the rural-urban gradient. We conclude that socio-cultural preferences toward ecosystem services can serve as a tool to identify relevant services for people, the factors underlying these social preferences, and emerging ecosystem service bundles and trade-offs. PMID:22720006

  12. Twisted vector bundles on pointed nodal curves

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    DEFINITION 2.5. Let C → S be an n-pointed nodal curve over a k-scheme S and let ξ be a principal G- bundle on Cgen. A chart (U, η, ) for ξ is called balanced, if for each ... branches is via multiplication with primitive roots of unity which are inverse to each other. ...... Condition (16) implies that A0 is a block matrix of the form.

  13. Principal bundles on the projective line

    Indian Academy of Sciences (India)

    M. Senthilkumar (Newgen Imaging) 1461 1996 Oct 15 13:05:22

    LetX be a complete nonsingular curve over the algebraic closurek ofk andGa reductive group over k. Let E → X be a principal G-bundle on X. E is said to be semistable if, for every reduction of structure group EP ⊂ E to a maximal parabolic subgroup P of G, we have degree EP (p) ≤ 0, where p is the Lie algebra of P and EP ...

  14. Abelian conformal field theory and determinant bundles

    DEFF Research Database (Denmark)

    Andersen, Jørgen Ellegaard; Ueno, K.


    are up to a scale the same as the curvature of the connections constructed in [14, 16]. We study the sewing construction for nodal curves and its explicit relation to the constructed connections. Finally we construct preferred holomorphic sections of these line bundles and analyze their behaviour near...... nodal curves. These results are used in [4] to construct modular functors form the conformal field theories given in [14, 16] by twisting with an appropriate factional power of this Abelian theory....

  15. Uncovering ecosystem service bundles through social preferences.

    Directory of Open Access Journals (Sweden)

    Berta Martín-López

    Full Text Available Ecosystem service assessments have increasingly been used to support environmental management policies, mainly based on biophysical and economic indicators. However, few studies have coped with the social-cultural dimension of ecosystem services, despite being considered a research priority. We examined how ecosystem service bundles and trade-offs emerge from diverging social preferences toward ecosystem services delivered by various types of ecosystems in Spain. We conducted 3,379 direct face-to-face questionnaires in eight different case study sites from 2007 to 2011. Overall, 90.5% of the sampled population recognized the ecosystem's capacity to deliver services. Formal studies, environmental behavior, and gender variables influenced the probability of people recognizing the ecosystem's capacity to provide services. The ecosystem services most frequently perceived by people were regulating services; of those, air purification held the greatest importance. However, statistical analysis showed that socio-cultural factors and the conservation management strategy of ecosystems (i.e., National Park, Natural Park, or a non-protected area have an effect on social preferences toward ecosystem services. Ecosystem service trade-offs and bundles were identified by analyzing social preferences through multivariate analysis (redundancy analysis and hierarchical cluster analysis. We found a clear trade-off among provisioning services (and recreational hunting versus regulating services and almost all cultural services. We identified three ecosystem service bundles associated with the conservation management strategy and the rural-urban gradient. We conclude that socio-cultural preferences toward ecosystem services can serve as a tool to identify relevant services for people, the factors underlying these social preferences, and emerging ecosystem service bundles and trade-offs.

  16. Uncovering ecosystem service bundles through social preferences. (United States)

    Martín-López, Berta; Iniesta-Arandia, Irene; García-Llorente, Marina; Palomo, Ignacio; Casado-Arzuaga, Izaskun; Amo, David García Del; Gómez-Baggethun, Erik; Oteros-Rozas, Elisa; Palacios-Agundez, Igone; Willaarts, Bárbara; González, José A; Santos-Martín, Fernando; Onaindia, Miren; López-Santiago, Cesar; Montes, Carlos


    Ecosystem service assessments have increasingly been used to support environmental management policies, mainly based on biophysical and economic indicators. However, few studies have coped with the social-cultural dimension of ecosystem services, despite being considered a research priority. We examined how ecosystem service bundles and trade-offs emerge from diverging social preferences toward ecosystem services delivered by various types of ecosystems in Spain. We conducted 3,379 direct face-to-face questionnaires in eight different case study sites from 2007 to 2011. Overall, 90.5% of the sampled population recognized the ecosystem's capacity to deliver services. Formal studies, environmental behavior, and gender variables influenced the probability of people recognizing the ecosystem's capacity to provide services. The ecosystem services most frequently perceived by people were regulating services; of those, air purification held the greatest importance. However, statistical analysis showed that socio-cultural factors and the conservation management strategy of ecosystems (i.e., National Park, Natural Park, or a non-protected area) have an effect on social preferences toward ecosystem services. Ecosystem service trade-offs and bundles were identified by analyzing social preferences through multivariate analysis (redundancy analysis and hierarchical cluster analysis). We found a clear trade-off among provisioning services (and recreational hunting) versus regulating services and almost all cultural services. We identified three ecosystem service bundles associated with the conservation management strategy and the rural-urban gradient. We conclude that socio-cultural preferences toward ecosystem services can serve as a tool to identify relevant services for people, the factors underlying these social preferences, and emerging ecosystem service bundles and trade-offs.

  17. Forced and gravity reflood experiments in hexagonal bundle lattices. Final report; Zwangs- und Schwerkraftflutversuche an hexagonalen Stabbuendelgeometrien; Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Wiehr, K.; Erbacher, F.; Just, W.; Harten, U.; Schmidt, H.


    This report describes reflooding experiments in two different fuel rod simulator bundles (FRSB) with hexagonal lattices in different bundle geometries and different pitch over diameter (p/d) ratios. The bundles consist of 16 electrically heated fuel rod simulators with a cosine shaped axial power profile. The tight bundle (p/d=1,06) has steel claddings with integrated helical fins as spacers, whereas the wider bundle (p/d=1,24) is equipped with grid spacers and with Zircaloy claddings typical of a convoy PWR. This report delivers mainly the data base for modelers in order to verify and further develop reflooding codes (e.g. ATHLET, RELAP) for hexagonal fuel lattices. Presently this is of immediate interest for the hexagonal fuel elements of Russian VVER`s and other advanced reactor concepts. The experimental data of a total of 45 experiments (most of them with forced feed and some of them with gravity feed) are stored on data tapes and data discs of the KfK IBM 3090. To find the proper experiments described for calculations, this report contains schematic figures of the test loop, the instrumentation of the bundle and the whole test section. The test parameters are listed in tables. To facilitate the identification of the experiments, the cladding temperatures of the inner 37 fuel rod simulators, the axial cladding temperatures and the total pressure drop of the bundle are plotted. A user description for the experimental data and the corresponding measuring channel list of each experiment enables to find the proper test. In the appendix the material properties to model the rod simulator are given. (orig.) [Deutsch] Dieser Bericht beschreibt Flutexperimente an zwei Brennstabsimulatorbuendeln mit hexagonaler Stabanordnung unterschiedlicher Buendelgeometrie. Die Buendel bestehen aus jeweils 61 Brennstabsimulatoren (BSS) mit einem cosinusfoermigen axialen Leistungsprofil, wobei das sehr enge Buendel (p/d=1,06) mit Stahlhuellen mit integrierten Wendelrippen als

  18. Study and modelling of a reactional tube bundle heated by a fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Collantes Hernandez, M.A.


    Fluidized beds exhibit two important characteristics for the heating of a reactional tube bundle: homogeneous temperature within all the fluidized bed and high heat transfer coefficient with the immersed surfaces. One of the key points for their modeling is the knowledge of the vertical and horizontal thermal conductivities and the heat transfer coefficient at the wall or with the tubes of the reactor. As thermal diffusivity data about large fluidized beds are not available in the literature, we have built a large size pilot unit (0.6 m x 1.1 m x 2.8 m) to determine these values under the conditions of a catalytic treatment of petroleum products. The measure of local temperatures and the use of a two-dimensional diffusion model have permitted us to determine thermal conductivities as a function of several parameters: fluidization velocity, height of the bed, nature and granulometry of solids and geometry of the tube bundle. On the basis of the collected experimental data, the case of a petrochemical unit has been studied. A mathematical code was developed, which permitted us to acquire the data concerning the progress of the reaction in the tubes and it also allowed us to analyse the influence of size and density of the tube bundles on the conversion. (author). 72 refs., 90 figs., 15 tabs.

  19. Some features of horizontally oriented low-current electric arc in air

    Energy Technology Data Exchange (ETDEWEB)

    Tazmeev, Kh. K., E-mail: [Kazan (Volga Region) Federal University, Naberezhnye Chelny Institute (Russian Federation); Tazmeev, B. Kh., E-mail: [National Research Technical University, Naberezhnye Chelny Branch (Russian Federation)


    The properties of an electric arc operating in open air at currents of lower than 1 A were studied experimentally. The rod cathode was oriented horizontally. Cylindrical rods and plane plates either installed strictly vertically in front of the cathode end or tilted at a certain angle served as the anode. It is shown that, with such an electrode configuration, it is possible to form a discharge channel much longer than the electrode gap length. Regimes of regular oscillations are revealed, and conditions for their appearance are established. The electric field strength in the arc column and the electron temperature near the anode are calculated.

  20. International symposium on fuel rod simulators: development and application

    Energy Technology Data Exchange (ETDEWEB)

    McCulloch, R.W. (comp.)


    Separate abstracts are included for each of the papers presented concerning fuel rod simulator operation and performance; simulator design and evaluation; clad heated fuel rod simulators and fuel rod simulators for cladding investigations; fuel rod simulator components and inspection; and simulator analytical modeling. Ten papers have previously been input to the Energy Data Base.


    Directory of Open Access Journals (Sweden)

    Stjepan Antolović


    Full Text Available The interest and performance of horizontal drilling and completions has increased during the last two decades. Horizontal wells are advantageous compared to vertical wells in thin reservoirs, reservoirs with favorable vertical permeability and reservoirs with water and gas coning problems. In many reservoirs, the ratio of horizontal permeability to the vertical permeability is substantially larger than one and often is close to 10. Thus, these reservoirs are very good candidates for hydraulic fracturing. By hydraulic fracturing one or more fractures are created, which can be longitudinal or orthogonal. By that, flow is altered and it mostly conducts horizontally through reservoir toward horizontal wellbore. With this altered flow, fluid is produced faster, with less pressure loss by fluid unit of produced fluid. Some of the existing mathematical models to determine the productivity of multifractured horizontal wells are presented in this work (the paper is published in Croatian.

  2. Bundling harvester; Harvennuspuun automaattisen nippukorjausharvesterin kehittaeminen

    Energy Technology Data Exchange (ETDEWEB)

    Koponen, K. [Eko-Log Oy, Kuopio (Finland)


    The starting point of the project was to design and construct, by taking the silvicultural point of view into account, a harvesting and processing system especially for energy-wood, containing manually driven bundling harvester, automating of the harvester, and automated loading. The equipment forms an ideal method for entrepreneur`s-line harvesting. The target is to apply the system also for owner`s-line harvesting. The profitability of the system promotes the utilisation of the system in both cases. The objectives of the project were: to construct a test equipment and prototypes for all the project stages, to carry out terrain and strain tests in order to examine the usability and durability, as well as the capacity of the machine, to test the applicability of the Eko-Log system in simultaneous harvesting of energy and pulp woods, and to start the marketing and manufacturing of the products. The basic problems of the construction of the bundling harvester have been solved using terrain-tests. The prototype machine has been shown to be operable. Loading of the bundles to form sufficiently economically transportable loads has been studied, and simultaneously, the branch-biomass has been tried to be utilised without loosing the profitability of transportation. The results have been promising, and will promote the profitable utilisation of wood-energy. (orig.)

  3. An analytical fiber bundle model for pullout mechanics of root bundles (United States)

    Cohen, D.; Schwarz, M.; Or, D.


    Roots in soil contribute to the mechanical stability of slopes. Estimation of root reinforcement is challenging because roots form complex biological networks whose geometrical and mechanical characteristics are difficult to characterize. Here we describe an analytical model that builds on simple root descriptors to estimate root reinforcement. Root bundles are modeled as bundles of heterogeneous fibers pulled along their long axes neglecting root-soil friction. Analytical expressions for the pullout force as a function of displacement are derived. The maximum pullout force and corresponding critical displacement are either derived analytically or computed numerically. Key model inputs are a root diameter distribution (uniform, Weibull, or lognormal) and three empirical power law relations describing tensile strength, elastic modulus, and length of roots as functions of root diameter. When a root bundle with root tips anchored in the soil matrix is pulled by a rigid plate, a unique parameter, ?, that depends only on the exponents of the power law relations, dictates the order in which roots of different diameters break. If ? 1, large roots break first. When ? = 1, all fibers break simultaneously, and the maximum tensile force is simply the roots' mean force times the number of roots in the bundle. Based on measurements of root geometry and mechanical properties, the value of ? is less than 1, usually ranging between 0 and 0.7. Thus, small roots always fail first. The model shows how geometrical and mechanical characteristics of roots and root diameter distribution affect the pullout force, its maximum and corresponding displacement. Comparing bundles of roots that have similar mean diameters, a bundle with a narrow variance in root diameter will result in a larger maximum force and a smaller displacement at maximum force than a bundle with a wide diameter distribution. Increasing the mean root diameter of a bundle without changing the distribution's shape increases

  4. Nuclear materials testing in the loops of the NRU research reactor using material test bundles

    Energy Technology Data Exchange (ETDEWEB)

    Leung, T.C.; Walters, L. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada)


    The NRU research reactor has been used to obtain data to understand and quantify the effects of irradiation on nuclear reactor components through their in-service lives and to develop improved designs and components. Apart from the Mark-4 and Mark-7 fast neutron rod material testing facilities in NRU, the high-pressure/high-temperature experimental loops provide an environment similar to the CANDU reactor core, where test materials are subjected to simulated power reactor conditions. Nuclear materials are tested in the loops using Material Test Bundles (MTB). This paper describes how the MTB is designed to operate in the NRU loops. It also describes the physics calculation of the 89-energy-group neutron spectrum in the MTB and its comparison with the spectrum in CANDU power reactors. The predictions of spectral effects on nuclear material behaviour, such as material damage and helium generation are summarized. (author)

  5. Regulatory perspective on incomplete control rod insertions

    Energy Technology Data Exchange (ETDEWEB)

    Chatterton, M.


    The incomplete control rod insertions experienced at South Texas Unit 1 and Wolf Creek are of safety concern to the NRC staff because they represent potential precursors to loss of shutdown margin. Even before it was determined if these events were caused by the control rods or by the fuel there was an apparent correlation of the problem with high burnup fuel. It was determined that there was also a correlation between high burnup and high drag forces as well as with rod drop time histories and lack of rod recoil. The NRC staff initial actions were aimed at getting a perspective on the magnitude of the problem as far as the number of plants and the amount of fuel that could be involved, as well as the safety significance in terms of shutdown margin. As tests have been performed and data has been analyzed the focus has shifted more toward understanding the problem and the ways to eliminate it. At this time the staff`s understanding of the phenomena is that it was a combination of factors including burnup, power history and temperature. The problem appears to be very sensitive to these factors, the interaction of which is not clearly understood. The model developed by Westinghouse provides a possible explanation but there is not sufficient data to establish confidence levels and sensitivity studies involving the key parameters have not been done. While several fixes to the problem have been discussed, no definitive fixes have been proposed. Without complete understanding of the phenomena, or fixes that clearly eliminate the problem the safety concern remains. The safety significance depends on the amount of shutdown margin lost due to incomplete insertion of the control rods. Were the control rods to stick high in the core, the reactor could not be shutdown by the control rods and other means such as emergency boration would be required.


    Directory of Open Access Journals (Sweden)

    Petr Kracík


    Full Text Available Water flowing on a sprinkled tube bundle forms three basic modes: the Droplet mode (the liquid drips from one tube to another, the Jet mode (with an increasing flow rate, the droplets merge into a column and the Membrane (Sheet mode (with a further increase in the flow rate of the falling film liquid, the columns merge and create sheets between the tubes. With a sufficient flow rate, the sheets merge at this stage, and the tube bundle is completely covered by a thin liquid film. There are several factors influencing both the individual modes and the heat transfer. Beside the above-mentioned falling film liquid flow rate, these are for instance the tube diameters, the tube pitches in the tube bundle, or the physical conditions of the falling film liquid. This paper presents a summary of data measured at atmospheric pressure, with a tube bundle consisting of copper tubes of 12 millimetres in diameter, and with a studied tube length of one meter. The tubes are situated horizontally one above another at a pitch of 15 to 30 mm, and there is a distribution tube placed above them with water flowing through apertures of 1.0mm in diameter at a 9.2mm span. Two thermal conditions have been tested with all pitches: 15 °C to 40 °C and 15 °C to 45 °C. The temperature of the falling film liquid, which was heated during the flow through the exchanger, was 15 °C at the distribution tube input. The temperature of the heating liquid at the exchanger input, which had a constant flow rate of approx. 7.2. litres per minute, was 40 °C, or alternatively 45 °C.

  7. Radiological characterization of spent control rod assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Lepel, E.A.; Robertson, D.E.; Thomas, C.W.; Pratt, S.L.; Haggard, D.L. [Pacific Northwest Lab., Richland, WA (United States)


    This document represents the final report of an ongoing study to provide radiological characterizations, classifications, and assessments in support of the decommissioning of nuclear power stations. This report describes the results of non-destructive and laboratory radionuclide measurements, as well as waste classification assessments, of BWR and PWR spent control rod assemblies. The radionuclide inventories of these spent control rods were determined by three separate methodologies, including (1) direct assay techniques, (2) calculational techniques, and (3) by sampling and laboratory radiochemical analyses. For the BWR control rod blade (CRB) and PWR burnable poison rod assembly (BPRA), {sup 60}Co and {sup 63}Ni, present in the stainless steel cladding, were the most abundant neutron activation products. The most abundant radionuclide in the PWR rod cluster control assembly (RCCA) was {sup 108m}Ag (130 yr halflife) produced in the Ag-In-Cd alloy used as the neutron poison. This radionuclide will be the dominant contributor to the gamma dose rate for many hundreds of years. The results of the direct assay methods agree very well ({+-}10%) with the sampling/radiochemical measurements. The results of the calculational methods agreed fairly well with the empirical measurements for the BPRA, but often varied by a factor of 5 to 10 for the CRB and the RCCA assemblies. If concentration averaging and encapsulation, as allowed by 10CFR61.55, is performed, then each of the entire control assemblies would be classified as Class C low-level radioactive waste.

  8. Broadband Vibration Attenuation Using Hybrid Periodic Rods

    Directory of Open Access Journals (Sweden)

    S. Asiri


    Full Text Available This paper presents both theoretically and experimentally a new kind of a broadband vibration isolator. It is a table-like system formed by four parallel hybrid periodic rods connected between two plates. The rods consist of an assembly of periodic cells, each cell being composed of a short rod and piezoelectric inserts. By actively controlling the piezoelectric elements, it is shown that the periodic rods can efficiently attenuate the propagation of vibration from the upper plate to the lower one within critical frequency bands and consequently minimize the effects of transmission of undesirable vibration and sound radiation. In such a system, longitudinal waves can propagate from the vibration source in the upper plate to the lower one along the rods only within specific frequency bands called the "Pass Bands" and wave propagation is efficiently attenuated within other frequency bands called the "Stop Bands". The spectral width of these bands can be tuned according to the nature of the external excitation. The theory governing the operation of this class of vibration isolator is presented and their tunable filtering characteristics are demonstrated experimentally as functions of their design parameters. This concept can be employed in many applications to control the wave propagation and the force transmission of longitudinal vibrations both in the spectral and spatial domains in an attempt to stop/attenuate the propagation of undesirable disturbances.

  9. Friction measuring device for control rod

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Tomomi.


    In the present invention, judgment for friction of control rods conducted upon periodical inspection of a BWR type power plant is conducted by automatic analysis and evaluation by digitalizing data of an operation pressure and an differential pressure of control rods. That is, a differential pressure detection means detects a pressure and a differential pressure of driving water of a control rod driving source. A data processing device conducts digital analysis and store data from the differential pressure detection means, as well as compares the data with set values to automatically judge the friction of the control rod to diagnose abnormality based on the changing trend of the analyzed data. According to the device of the present invention, data measured for the friction of a great number of control rods can be analyzed and judged automatically in a short period of time. Accordingly, evaluation can be conducted accurately even by less skilled operators. Further, when an abnormality is detected, the diagnosis thereof is conducted, so that the operation is simplified and an operator's burden upon inspection can be mitigated. (I.S.).

  10. Wetting of a partially immersed compliant rod (United States)

    Hui, Chung-Yuen; Jagota, Anand


    The force on a solid rod partially immersed in a liquid is commonly used to determine the liquid-vapor surface tension by equating the measured force required to remove the rod from the liquid to the vertical component of the liquid-vapor surface tension. Here, we study how this process is affected when the rod is compliant. For equilibrium, we enforce force and configurational energy balance, including contributions from elastic energy. We show that, in general, the contact angle does not equal that given by Young's equation. If surface stresses are tensile, the strain in the immersed part of the rod is found to be compressive and to depend only on the solid-liquid surface stress. The strain in the dry part of the rod can be either tensile or compressive, depending on a combination of parameters that we identify. We also provide results for compliant plates partially immersed in a liquid under plane strain and plane stress. Our results can be used to extract solid surface stresses from such experiments.

  11. Bent Telescopic Rods in Patients With Osteogenesis Imperfecta. (United States)

    Lee, R Jay; Paloski, Michael D; Sponseller, Paul D; Leet, Arabella I


    Telescopic rods require alignment of 2 rods to enable lengthening. A telescopic rod converts functionally into a solid rod if either rod bends, preventing proper engagement. Our goal was to characterize implant bending as a mode of failure of telescopic rods used in the treatment of osteogenesis imperfecta in children. We conducted a retrospective review of our osteogenesis imperfecta database for patients treated with intramedullary telescopic rods at our institution from 1992 through 2010 and identified 12 patients with bent rods. The 6 boys and 6 girls had an average age at the time of initial surgery of 3.1 years (range, 1.8 to 8.3 y) and a total of 51 telescoping rods. Clinic notes, operative reports, and radiographs were reviewed. The rods were analyzed for amount of lengthening, characteristics of bending, presence of cut out, or disengagement from an anchor point. Bends in the rods were characterized by their location on the implant component. The bent and straight rods were compared. Data were analyzed with the Mann-Whitney test (statistical significance set at P≤0.05). Of the 51 telescoping rods, 17 constructs (33%) bent. The average interval between surgery and rod bending was 4.0 years (range, 0.9 to 8.2 y). Before bending, 11 of 17 telescoping rods had routine follow-up radiographs for review. In 10 of the rods, bending was present when early signs of rod failure were first detected. Rod bending did not seem to be related to rod size. There was no area on the rod itself that seemed more susceptible to bending. Rod bending can be an early sign of impending rod failure. When rod bending is first noted, it may predispose the rod to other subsequent failures such as loss of proximal and distal fixation and cut out. Rod bending should be viewed as an indicator for closer monitoring of the patient and discussions regarding future need for rod exchange. Level III-retrospective review.

  12. Development of immunoaffinity solid phase microextraction rods for analysis of three estrogens in environmental water samples. (United States)

    Wang, Cuicui; Yang, Linyan; Li, Na; Zhang, Xinda; Guo, Yongze; Li, Cun


    In this study, immunoaffinity solid phase microextraction (SPME) rods were developed for the analysis of diethylstilbestrol (DES), hexestrol (HES) and dienestrol (DIS) followed by ultra high-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). This immunoaffinity SPME device was built with three stainless steel rods bundled together as one and modified with porous silicate particles. As an extraction sorbent, antibody immobilization approach was employed based on the covalent attachment of the anti-diethylstilbestrol monoclonal antibody (mAb) onto the rods. The immunoaffinity SPME rod was characterized and confirmed by scanning electron microscopy and X-ray photoelectron spectroscopy analysis. The porous network showed a very large active surface area and significantly increased the adsorption capacity which can reach 49.6pmol/cm(2). Moreover, the immunoaffinity sorbent showed good sturdiness at least 10 times with stable extraction performance. Once the main experimental parameters were optimized, the method was used to detect DES, HES and DIS in environmental water samples. The limits of detection for the three estrogens were 0.05-0.15ng/mL, and the limits of quantification was 0.5ng/mL. The average recoveries ranged from 34.2 to 62.7% were achieved with good intra-day and inter-day precision ranging from 7.8 to 12.7% and from 8.2 to 13.5% respectively. The newly developed immunoaffinity SPME showed high adsorption capacity, good sensitivity and reproducibility and was successfully applied to the analysis of DES, HES and DIS in environmental water samples. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Color dissociation artifacts in double Maddox rod cyclodeviation testing. (United States)

    Simons, K; Arnoldi, K; Brown, M H


    The double Maddox rod test, based on a red Maddox rod in front of one eye and a clear Maddox rod in front of the other, is used to measure cyclodeviation, typically in patients with superior oblique muscle pareses. Discrepant results between the double Maddox rod test and other torsion measures, and reports of "paradoxic" cyclodeviation in the normal eye of some patients with superior oblique paresis, suggest the two-color format of the double Maddox rod test may produce artifactual torsion measures. Forty patients with superior oblique paresis were tested twice using the double Maddox rod test, reversing the red and white Maddox rods between eyes for the second test, and 18 were tested further with same-color red or clear Maddox rods in front of both eyes. With the standard double Maddox rod test, 33 (83%) of 40 patients localized their cyclodeviation to the eye viewing through the red Maddox rod, irrespective of laterality of the paresis or fixation preference. In all 33 patients, laterality of the perceived torsion changed between eyes when testing was repeated with red and white Maddox rods interchanged between eyes. With same-color Maddox rods before both eyes, 17 (94%) of 18 patients localized extorsion to the paretic eye. There was 7.6:1 ratio of luminance transmission and a 1.6:1 ratio of grating spatial frequency bandpass in the plano meridian between the clear and red Maddox rods, which appear to be responsible for the double Maddox rod test artifact. The traditional double Maddox rod test may produce artifactual cyclodeviation measurements. An alternative version of the test, based on same-color Maddox rods in front of both eyes, is proposed. The relatively high spatial frequency bandpass characteristics of the plano meridian of the Maddox rod (as high as 20/25 Snellen equivalent resolution through the clear Maddox rod) also suggests double Maddox rod testing should be conducted in a dark room to avoid biases from visual environment cues.

  14. Influence of Bundle Diameter and Attachment Point on Kinematic Behavior in Double Bundle Anterior Cruciate Ligament Reconstruction Using Computational Model

    Directory of Open Access Journals (Sweden)

    Oh Soo Kwon


    Full Text Available A protocol to choose the graft diameter attachment point of each bundle has not yet been determined since they are usually dependent on a surgeon’s preference. Therefore, the influence of bundle diameters and attachment points on the kinematics of the knee joint needs to be quantitatively analyzed. A three-dimensional knee model was reconstructed with computed tomography images of a 26-year-old man. Based on the model, models of double bundle anterior cruciate ligament (ACL reconstruction were developed. The anterior tibial translations for the anterior drawer test and the internal tibial rotation for the pivot shift test were investigated according to variation of bundle diameters and attachment points. For the model in this study, the knee kinematics after the double bundle ACL reconstruction were dependent on the attachment point and not much influenced by the bundle diameter although larger sized anterior-medial bundles provided increased stability in the knee joint. Therefore, in the clinical setting, the bundle attachment point needs to be considered prior to the bundle diameter, and the current selection method of graft diameters for both bundles appears justified.

  15. Monopoles and Modifications of Bundles over Elliptic Curves

    Directory of Open Access Journals (Sweden)

    Andrey M. Levin


    Full Text Available Modifications of bundles over complex curves is an operation that allows one to construct a new bundle from a given one. Modifications can change a topological type of bundle. We describe the topological type in terms of the characteristic classes of the bundle. Being applied to the Higgs bundles modifications establish an equivalence between different classical integrable systems. Following Kapustin and Witten we define the modifications in terms of monopole solutions of the Bogomolny equation. We find the Dirac monopole solution in the case R × (elliptic curve. This solution is a three-dimensional generalization of the Kronecker series. We give two representations for this solution and derive a functional equation for it generalizing the Kronecker results. We use it to define Abelian modifications for bundles of arbitrary rank. We also describe non-Abelian modifications in terms of theta-functions with characteristic.

  16. Heat Transfer Analysis in Wire Bundles for Aerospace Vehicles (United States)

    Rickman, S. L.; Iamello, C. J.


    Design of wiring for aerospace vehicles relies on an understanding of "ampacity" which refers to the current carrying capacity of wires, either, individually or in wire bundles. Designers rely on standards to derate allowable current flow to prevent exceedance of wire temperature limits due to resistive heat dissipation within the wires or wire bundles. These standards often add considerable margin and are based on empirical data. Commercial providers are taking an aggressive approach to wire sizing which challenges the conventional wisdom of the established standards. Thermal modelling of wire bundles may offer significant mass reduction in a system if the technique can be generalized to produce reliable temperature predictions for arbitrary bundle configurations. Thermal analysis has been applied to the problem of wire bundles wherein any or all of the wires within the bundle may carry current. Wire bundles present analytical challenges because the heat transfer path from conductors internal to the bundle is tortuous, relying on internal radiation and thermal interface conductance to move the heat from within the bundle to the external jacket where it can be carried away by convective and radiative heat transfer. The problem is further complicated by the dependence of wire electrical resistivity on temperature. Reduced heat transfer out of the bundle leads to higher conductor temperatures and, hence, increased resistive heat dissipation. Development of a generalized wire bundle thermal model is presented and compared with test data. The steady state heat balance for a single wire is derived and extended to the bundle configuration. The generalized model includes the effects of temperature varying resistance, internal radiation and thermal interface conductance, external radiation and temperature varying convective relief from the free surface. The sensitivity of the response to uncertainties in key model parameters is explored using Monte Carlo analysis.

  17. Isomonodromic Deformations and Very Stable Vector Bundles of Rank Two (United States)

    Biswas, Indranil; Heu, Viktoria; Hurtubise, Jacques


    For the universal isomonodromic deformation of an irreducible logarithmic rank two connection over a smooth complex projective curve of genus at least two, consider the family of holomorphic vector bundles over curves underlying this universal deformation. In a previous work we proved that the vector bundle corresponding to a general parameter of this family is stable. Here we prove that the vector bundle corresponding to a general parameter is in fact very stable, meaning it does not admit any nonzero nilpotent Higgs field.

  18. Bundling Products and Services Through Modularization Strategies

    DEFF Research Database (Denmark)

    Bask, Anu; Hsuan, Juliana; Rajahonka, Mervi


    Modularity has been recognized as a powerful tool in improving the efficiency and management of product design and manufacturing. However, the integrated view on covering both, product and service modularity for product-service systems (PSS), is under researched. Therefore, in this paper our...... objective is to contribute to the PSS modularity. Thus, we describe configurations of PSSs and the bundling of products and services through modularization strategies. So far there have not been tools to analyze and determine the correct combinations of degrees of product and service modularities....

  19. Differential geometry bundles, connections, metrics and curvature

    CERN Document Server

    Taubes, Clifford Henry


    Bundles, connections, metrics and curvature are the 'lingua franca' of modern differential geometry and theoretical physics. This book will supply a graduate student in mathematics or theoretical physics with the fundamentals of these objects. Many of the tools used in differential topology are introduced and the basic results about differentiable manifolds, smooth maps, differential forms, vector fields, Lie groups, and Grassmanians are all presented here. Other material covered includes the basic theorems about geodesics and Jacobi fields, the classification theorem for flat connections, the

  20. Affine Flag Manifolds and Principal Bundles

    CERN Document Server

    Schmitt, Alexander HW


    Affine flag manifolds are infinite dimensional versions of familiar objects such as Gramann varieties. The book features lecture notes, survey articles, and research notes - based on workshops held in Berlin, Essen, and Madrid - explaining the significance of these and related objects (such as double affine Hecke algebras and affine Springer fibers) in representation theory (e.g., the theory of symmetric polynomials), arithmetic geometry (e.g., the fundamental lemma in the Langlands program), and algebraic geometry (e.g., affine flag manifolds as parameter spaces for principal bundles). Novel

  1. Vector bundles on complex projective spaces

    CERN Document Server

    Okonek, Christian; Spindler, Heinz


    This expository treatment is based on a survey given by one of the authors at the Séminaire Bourbaki in November 1978 and on a subsequent course held at the University of Göttingen. It is intended to serve as an introduction to the topical question of classification of holomorphic vector bundles on complex projective spaces, and can easily be read by students with a basic knowledge of analytic or algebraic geometry. Short supplementary sections describe more advanced topics, further results, and unsolved problems.

  2. Sensitivity study of control rod depletion coefficients


    Blomberg, Joel


    This report investigates the sensitivity of the control rod depletion coefficients, Sg, to different input parameters and how this affects the accumulated 10B depletion, β. Currently the coefficients are generated with PHOENIX4, but the geometries can be more accurately simulated in McScram. McScram is used to calculate Control Rod Worth, which in turn is used to calculate Nuclear End Of Life, and Sg cannot be generated in the current version of McScram. Therefore, it is also analyzed whether...

  3. Pattern selection dynamics in rod eutectics (United States)

    Serefoglu, Melis

    The cooperative or diffusively coupled growth of multiple phases during solidification is one of the most widely observed and generally important classes of phase transformations in materials. Technologically, low melting temperature and small freezing range contribute to excellent casting fluidity and fine composite structures give rise to favorable properties. Both of these features contribute to the wide application of eutectic alloys in the casting, welding, and soldering of engineered components. Despite the broad-based technological importance, many fundamental questions regarding eutectic solidification remain unanswered, severely limiting our ability to employ computational methods in the prediction of microstructure for the effective design of new materials and processes. At the core of the most persistent questions, lie problems involving multicomponent thermodynamics, solid-liquid and solid-solid interfacial phenomena, morphological stability, chemical and thermal diffusion, and nucleation phenomena. In the current study, pattern selection dynamics in rod eutectics are investigated using systematic directional solidification experiments and phase field simulations. Directional solidification of a succinonitrile-camphor (SCN-DC) transparent alloy in thin slab geometries of various thicknesses reveals two main points. First, a velocity is indentified at which a transition in array basis vectors is observed in specimens with many rows of rods (i.e. bulk). This transition amounts to a 90 degree rotation of the rod array, shifting from alignment of 1st nearest neighbors to alignment of 2nd nearest neighbors along the slide wall. Second, significant array distortion is observed with decreasing slide thickness, delta, which ultimately leads to a single-row (quasi-3D) morphology where delta/lambda is on the order of unity. In our analysis of these observations, we use a geometrical model to describe the rod arrangement as a function of slide thickness, providing

  4. Discontinuous conduction in mouse bundle branches is caused by bundle-branch architecture

    NARCIS (Netherlands)

    van Veen, Toon A. B.; van Rijen, Harold V. M.; van Kempen, Marjan J. A.; Miquerol, Lucile; Opthof, Tobias; Gros, Daniel; Vos, Marc A.; Jongsma, Habo J.; de Bakker, Jacques M. T.


    Background - Recordings of the electrical activity of mouse bundle branches ( BBs) suggest reduced conduction velocity ( CV) in the midseptal compared with the proximal part of the BB. The present study was performed to elucidate the mechanism responsible for this slowing of conduction. Methods and

  5. Enthalpy and void distributions in subchannels of PHWR fuel bundles

    Energy Technology Data Exchange (ETDEWEB)

    Park, J. W.; Choi, H.; Rhee, B. W. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)


    Two different types of the CANDU fuel bundles have been modeled for the ASSERT-IV code subchannel analysis. From calculated values of mixture enthalpy and void fraction distribution in the fuel bundles, it is found that net buoyancy effect is pronounced in the central region of the DUPIC fuel bundle when compared with the standard CANDU fuel bundle. It is also found that the central region of the DUPIC fuel bundle can be cooled more efficiently than that of the standard fuel bundle. From the calculated mixture enthalpy distribution at the exit of the fuel channel, it is found that the mixture enthalpy and void fraction can be highest in the peripheral region of the DUPIC fuel bundle. On the other hand, the enthalpy and the void fraction were found to be highest in the central region of the standard CANDU fuel bundle at the exit of the fuel channel. This study shows that the subchannel analysis is very useful in assessing thermal behavior of the fuel bundle that could be used in CANDU reactors. 10 refs., 4 figs., 2 tabs. (Author)

  6. An in vitro biomechanical comparison of single-rod, dual-rod, and dual-rod with transverse connector in anterior thoracolumbar instrumentation. (United States)

    Reddy, Chandan G; Magnetta, Michael; Dahdaleh, Nader S; Demmer, Matthew; Iyamah, Kingsley Abode; Lim, Tae-Hong; Torner, James C; Hitchon, Patrick W


    After thoracolumbar corpectomy, standard anterolateral instrumentation may consist of dual rods with cross-connectors. However, when the vertebral bodies are small or involved with disease, only 1 rod may be possible. To compare the biomechanics of an in vitro L1 corpectomy model using 1 rod, 2 rods, or 2 rods with 2 cross-connectors. Eight fresh frozen human cadaveric spines were potted from T9 to L3. Pure moments of 1.5, 3, and 4.5 Nm were applied, and the motion of the spine was measured using 3 infrared cameras. Loads were applied in flexion and extension, right and left lateral bending, and right and left axial rotation. Each spine was first tested in the intact state. After performing an L1 corpectomy and replacement with a carbon fiber reinforced polymer cage, 3 constructs were tested: single rod (1R), dual rod (2R), and dual rod with 2 transverse connectors (CC). Analysis of variance suggests significant main effects of load (P < .0001), axis (P = .022), construct (P =.0019), and individual spine (P < .0001). Overall, the single-rod construct is significantly less rigid than the intact spine in axial rotation. There is no significant difference between the intact spine and either the dual-rod construct or the dual-rod cross-connector construct. In our in vitro model of anterior spinal stabilization after corpectomy and grafting, a single-rod construct is significantly less rigid than the intact spine. Addition of a second rod returns the rigidity of the spine to the intact state. A dual-rod cross-connector construct is significantly more rigid than a single-rod construct.

  7. Molybdenum-99-producing 37-element fuel bundle neutronically and thermal-hydraulically equivalent to a standard CANDU fuel bundle

    Energy Technology Data Exchange (ETDEWEB)

    Nichita, E., E-mail:; Haroon, J., E-mail:


    Highlights: • A 37-element fuel bundle modified for {sup 99}Mo production in CANDU reactors is presented. • The modified bundle is neutronically and thermal-hydraulically equivalent to the standard bundle. • The modified bundle satisfies all safety criteria satisfied by the standard bundle. - Abstract: {sup 99m}Tc, the most commonly used radioisotope in diagnostic nuclear medicine, results from the radioactive decay of {sup 99}Mo which is currently being produced at various research reactors around the globe. In this study, the potential use of CANDU power reactors for the production of {sup 99}Mo is investigated. A modified 37-element fuel bundle, suitable for the production of {sup 99}Mo in existing CANDU-type reactors is proposed. The new bundle is specifically designed to be neutronically and thermal-hydraulically equivalent to the standard 37-element CANDU fuel bundle in normal, steady-state operation and, at the same time, be able to produce significant quantities of {sup 99}Mo when irradiated in a CANDU reactor. The proposed bundle design uses fuel pins consisting of a depleted-uranium centre surrounded by a thin layer of low-enriched uranium. The new molybdenum-producing bundle is analyzed using the lattice transport code DRAGON and the diffusion code DONJON. The proposed design is shown to produce 4081 six-day Curies of {sup 99}Mo activity per bundle when irradiated in the peak-power channel of a CANDU core, while maintaining the necessary reactivity and power rating limits. The calculated {sup 99}Mo yield corresponds to approximately one third of the world weekly demand. A production rate of ∼3 bundles per week can meet the global demand of {sup 99}Mo.

  8. Static in situ test of the axial power shaping rod and shim safety control rod mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Soberano, F T; Gannon, J A; Parlee, K A


    There are eight Axial Power Shaping Rods (APSRs) and 61 Shim Safety Control Rods (SSCRs) within the Three Mile Island (TMI) Unit 2 reactor core. This report describes the test results for all eight APSRs and three SSCRs. The tests were performed in situ from the Control Rod Drive (CRD) system logic cabinets and the transformer cabinets located in the cable spreading room. The tests were intended to determine the condition of the Absolute Position Indicators (APIs), the stator thermocouples, and the stators, and to assess each components' survival of the TMI-2 accident.

  9. Design and evaluate finned tube bundles

    Energy Technology Data Exchange (ETDEWEB)

    Ganapathy, V. [ABCO Industries, Abilene, TX (United States)


    Finned tube bundles are widely used in heat exchangers, air coolers, waste heat boilers and fired heaters where energy transfer occurs between clean flue gases and a fluid with a high heat-transfer coefficient. They have several advantages including compactness, low gas pressure drop and low weight for a given duty compared to bare tube bundles. Choosing a fin type, arrangement and fin configuration requires a thorough analysis and economic evaluation. The solution is not unique since it depends on material and labor costs. Surface areas vary widely in finned tube designs for the same duty and gas pressure drop. Therefore, decisions should not be based on surface area alone. Plant engineers and consultants should consider operating costs in their evaluation because they accrue year after year. Selecting a boiler based on initial costs alone is not prudent. The paper discusses heat transfer and gas pressure drop with finned tubes, determining fin efficiency and effectiveness,g as pressure drop, tube wall and fin top temperatures, an example calculation, the effect of fin configuration on design, the effect of inline versus staggered arrangements and solid versus serrated fins, and concerns with high fin-density designs.

  10. Evaluation of Single-Bundle versus Double-Bundle PCL Reconstructions with More Than 10-Year Follow-Up

    Directory of Open Access Journals (Sweden)

    Masataka Deie


    Full Text Available Background. Posterior cruciate ligament (PCL injuries are not rare in acute knee injuries, and several recent anatomical studies of the PCL and reconstructive surgical techniques have generated improved patient results. Now, we have evaluated PCL reconstructions performed by either the single-bundle or double-bundle technique in a patient group followed up retrospectively for more than 10 years. Methods. PCL reconstructions were conducted using the single-bundle (27 cases or double-bundle (13 cases method from 1999 to 2002. The mean age at surgery was 34 years in the single-bundle group and 32 years in the double-bundle group. The mean follow-up period was 12.5 years. Patients were evaluated by Lysholm scoring, the gravity sag view, and knee arthrometry. Results. The Lysholm score after surgery was 89.1±5.6 points for the single-bundle group and 91.9±4.5 points for the double-bundle group. There was no significant difference between the methods in the side-to-side differences by gravity sag view or knee arthrometer evaluation, although several cases in both groups showed a side-to-side difference exceeding 5 mm by the latter evaluation method. Conclusions. We found no significant difference between single- and double-bundle PCL reconstructions during more than 10 years of follow-up.

  11. Oligo(naphthylene–ethynylene) Molecular Rods

    DEFF Research Database (Denmark)

    Cramer, Jacob Roland; Ning, Yanxiao; Shen, Cai


    of palladium-catalyzed Sonogashira reactions between naphthyl halides and acetylenes. The triazene functionality was used as a protected iodine precursor to allow linear extension of the molecular rods during the synthe-ses. The carboxylic acid groups in the target molecules were protected as esters during...

  12. Modeling and simulation performance of sucker rod beam pump

    Energy Technology Data Exchange (ETDEWEB)

    Aditsania, Annisa, E-mail: [Department of Computational Sciences, Institut Teknologi Bandung (Indonesia); Rahmawati, Silvy Dewi, E-mail:; Sukarno, Pudjo, E-mail: [Department of Petroleum Engineering, Institut Teknologi Bandung (Indonesia); Soewono, Edy, E-mail: [Department of Mathematics, Institut Teknologi Bandung (Indonesia)


    Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

  13. Rod photoreceptors express GPR55 in the adult vervet monkey retina.

    Directory of Open Access Journals (Sweden)

    Joseph Bouskila

    Full Text Available Cannabinoids exert their actions mainly through two receptors, the cannabinoid CB1 receptor (CB1R and cannabinoid CB2 receptor (CB2R. In recent years, the G-protein coupled receptor 55 (GPR55 was suggested as a cannabinoid receptor based on its activation by anandamide and tetrahydrocannabinol. Yet, its formal classification is still a matter of debate. CB1R and CB2R expression patterns are well described for rodent and monkey retinas. In the monkey retina, CB1R has been localized in its neural (cone photoreceptor, horizontal, bipolar, amacrine and ganglion cells and CB2R in glial components (Müller cells. The aim of this study was to determine the expression pattern of GPR55 in the monkey retina by using confocal microscopy. Our results show that GPR55 is strictly localized in the photoreceptor layer of the extrafoveal portion of the retina. Co-immunolabeling of GPR55 with rhodopsin, the photosensitive pigment in rods, revealed a clear overlap of expression throughout the rod structure with most prominent staining in the inner segments. Additionally, double-label of GPR55 with calbindin, a specific marker for cone photoreceptors in the primate retina, allowed us to exclude expression of GPR55 in cones. The labeling of GPR55 in rods was further assessed with a 3D visualization in the XZ and YZ planes thus confirming its exclusive expression in rods. These results provide data on the distribution of GPR55 in the monkey retina, different than CB1R and CB2R. The presence of GPR55 in rods suggests a function of this receptor in scotopic vision that needs to be demonstrated.

  14. Horizontal and Vertical Line Designs. (United States)

    Johns, Pat


    Presents an art lesson in which students learn about the artist Piet Mondrian and create their own abstract artworks. Focuses on geometric shapes using horizontal and vertical lines. Includes background information about the artist. (CMK)

  15. Notes on the horizontal cohomology


    Verbovetsky, Alexander


    This paper is devoted to the horizontal (``characteristic'') cohomology of systems of differential equations. Recent results on computing the horizontal cohomology via the compatibility complex are generalized. New results on the Vinogradov C-spectral sequence and the Krasil'shchik C-cohomology are obtained. As an application of general theory, the examples of an evolution equation and a p-form gauge theory are explicitly worked out.

  16. Mechanisms of Horizontal Gene Transfer


    Cafini Barrado, Fabio; Medrano Romero, Verónica; Morikawa, Kazuya


    Horizontal gene transfer plays important roles in the evolution of S. aureus, and indeed, a variety of virulence factors and antibiotic resistance genes are embedded in a series of mobile genetic elements. In this chapter, we review the mechanisms of horizontal gene transfer, including recent findings on the natural genetic competence. Then, we consider the transfer of two important antibiotic resistance genes: the methicillin resistance gene, mecA (in Staphylococcal Cassette Chromosome) and ...

  17. Articulated rods – a novel class of molecular rods based on oligospiroketals (OSK

    Directory of Open Access Journals (Sweden)

    Pablo Wessig


    Full Text Available We developed a new type of molecular rods consisting of two (or more rigid units linked by a flexible joint. Consequently we called these constructs articulated rods (ARs. The syntheses of ARs were carried out by a flexible and modular approach providing access to a number of compounds with various functionalizations in terminal positions. First applications were presented with pyrene, cinnamoyl and anthracenyl labelled ARs.

  18. An integral Riemann-Roch theorem for surface bundles

    DEFF Research Database (Denmark)

    Madsen, Ib Henning


    This paper is a response to a conjecture by T. Akita about an integral Riemann–Roch theorem for surface bundles.......This paper is a response to a conjecture by T. Akita about an integral Riemann–Roch theorem for surface bundles....

  19. Restriction Theorem for Principal bundles in Arbitrary Characteristic

    DEFF Research Database (Denmark)

    Gurjar, Sudarshan


    The aim of this paper is to prove two basic restriction theorem for principal bundles on smooth projective varieties in arbitrary characteristic generalizing the analogues theorems of Mehta-Ramanathan for vector bundles. More precisely, let G be a reductive algebraic group over an algebraically c...

  20. Phase Space Reduction of Star Products on Cotangent Bundles.

    NARCIS (Netherlands)

    Kowalzig, N.; Neumaier, N.; Pflaum, M.


    In this paper we construct star products on Marsden-Weinstein reduced spaces in case both the original phase space and the reduced phase space are (symplectomorphic to) cotangent bundles. Under the assumption that the original cotangent bundle $T^*Q$ carries a symplectic structure of form

  1. Monoubiquitination Inhibits the Actin Bundling Activity of Fascin. (United States)

    Lin, Shengchen; Lu, Shuang; Mulaj, Mentor; Fang, Bin; Keeley, Tyler; Wan, Lixin; Hao, Jihui; Muschol, Martin; Sun, Jianwei; Yang, Shengyu


    Fascin is an actin bundling protein that cross-links individual actin filaments into straight, compact, and stiff bundles, which are crucial for the formation of filopodia, stereocillia, and other finger-like membrane protrusions. The dysregulation of fascin has been implicated in cancer metastasis, hearing loss, and blindness. Here we identified monoubiquitination as a novel mechanism that regulates fascin bundling activity and dynamics. The monoubiquitination sites were identified to be Lys247 and Lys250, two residues located in a positive charge patch at the actin binding site 2 of fascin. Using a chemical ubiquitination method, we synthesized chemically monoubiquitinated fascin and determined the effects of monoubiquitination on fascin bundling activity and dynamics. Our data demonstrated that monoubiquitination decreased the fascin bundling EC50, delayed the initiation of bundle assembly, and accelerated the disassembly of existing bundles. By analyzing the electrostatic properties on the solvent-accessible surface of fascin, we proposed that monoubiquitination introduced steric hindrance to interfere with the interaction between actin filaments and the positively charged patch at actin binding site 2. We also identified Smurf1 as a E3 ligase regulating the monoubiquitination of fascin. Our findings revealed a previously unidentified regulatory mechanism for fascin, which will have important implications for the understanding of actin bundle regulation under physiological and pathological conditions. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

  2. Lexical Bundles in L1 and L2 Academic Writing (United States)

    Chen, Yu-Hua; Baker, Paul


    This paper adopts an automated frequency-driven approach to identify frequently-used word combinations (i.e., "lexical bundles") in academic writing. Lexical bundles retrieved from one corpus of published academic texts and two corpora of student academic writing (one L1, the other L2), were investigated both quantitatively and qualitatively.…

  3. Lexical Bundles: Facilitating University "Talk" in Group Discussions (United States)

    Heng, Chan Swee; Kashiha, Hadi; Tan, Helen


    Group discussion forms an integral language experience for most language learners, providing them with an opportunity to express themselves in a naturalistic setting. Multi-word expressions are commonly used and one of them is lexical bundles. Lexical bundles are types of extended collocations that occur more commonly than we expect; they are…

  4. A novel microbond bundle pullout technique to evaluate the ...

    Indian Academy of Sciences (India)


    Jul 26, 2017 ... to be a need to develop a microbond bundle pullout test that is comparable in all aspects to the semi-empirical resin slab/fibre bundle pullout approach [9]. The improvement of the known draw backs of the single fibre microbond pullout method [7], such as the difficulty in formulation and testing (with lack.

  5. Hair bundles are specialized for ATP delivery via creatine kinase.

    NARCIS (Netherlands)

    Shin, J.B.; Streijger, F.; Beynon, A.J.; Peters, T.; Gadzala, L.; McMillen, D.; Bystrom, C.; Zee, C.E.E.M. van der; Wallimann, T.; Gillespie, P.G.


    When stimulated strongly, a hair cell's mechanically sensitive hair bundle may consume ATP too rapidly for replenishment by diffusion. To provide a broad view of the bundle's protein complement, including those proteins participating in energy metabolism, we used shotgun mass spectrometry methods to

  6. Smooth Bundling of Large Streaming and Sequence Graphs

    NARCIS (Netherlands)

    Hurter, C.; Ersoy, O.; Telea, A.


    Dynamic graphs are increasingly pervasive in modern information systems. However, understanding how a graph changes in time is difficult. We present here two techniques for simplified visualization of dynamic graphs using edge bundles. The first technique uses a recent image-based graph bundling

  7. Computational imaging through a fiber-optic bundle (United States)

    Lodhi, Muhammad A.; Dumas, John Paul; Pierce, Mark C.; Bajwa, Waheed U.


    Compressive sensing (CS) has proven to be a viable method for reconstructing high-resolution signals using low-resolution measurements. Integrating CS principles into an optical system allows for higher-resolution imaging using lower-resolution sensor arrays. In contrast to prior works on CS-based imaging, our focus in this paper is on imaging through fiber-optic bundles, in which manufacturing constraints limit individual fiber spacing to around 2 μm. This limitation essentially renders fiber-optic bundles as low-resolution sensors with relatively few resolvable points per unit area. These fiber bundles are often used in minimally invasive medical instruments for viewing tissue at macro and microscopic levels. While the compact nature and flexibility of fiber bundles allow for excellent tissue access in-vivo, imaging through fiber bundles does not provide the fine details of tissue features that is demanded in some medical situations. Our hypothesis is that adapting existing CS principles to fiber bundle-based optical systems will overcome the resolution limitation inherent in fiber-bundle imaging. In a previous paper we examined the practical challenges involved in implementing a highly parallel version of the single-pixel camera while focusing on synthetic objects. This paper extends the same architecture for fiber-bundle imaging under incoherent illumination and addresses some practical issues associated with imaging physical objects. Additionally, we model the optical non-idealities in the system to get lower modelling errors.

  8. Frobenius pull backs of vector bundles in higher dimensions

    Indian Academy of Sciences (India)

    Frobenius pull backs; instability degree, vector bundles. 1. Introduction. Let X be a nonsingular projective variety defined over an algebraically closed field k of an arbitrary characteristic, and let H be a very ample line bundle on X. Let E be a torsion free sheaf on X. Then the notion of E being stable (resp. semistable) is well- ...

  9. On Harder–Narasimhan reductions for Higgs principal bundles

    Indian Academy of Sciences (India)

    in Ramanathan's paper. The aim of this paper is to generalize the methods of Biswas and Holla to give a unified approach to the case of principal bundles with Higgs structure on smooth projective varieties as well as the case of ramified bundles on smooth curves [4] (see §2, §5 for definitions). Recall that for the case of ...

  10. Sucker rod string design of the pumping systems

    Directory of Open Access Journals (Sweden)

    Chun Hua Liu


    Full Text Available The existing design of sucker rod string mainly focuses on the simplifying assumptions that rod string was exposed to simple tension loading. And its goal was to have equal modified stress at the top of each taper. The improved rod design was to have the same degree of safety at each section, and it used a dynamic force distribution that was proportional along the whole string. However, the available procedures did not provide the desired accuracy of its pertinent analysis, and the operators could not identify the specific phenomena that occur in CBM wells. In this paper, the mathematical models of rod loads and string length were developed based on the cyclic nature of rod string loading; the fatigue endurance method is used to design the single rod string; and the tapered rod string is designed to have an equal equivalent stress at the top of each section. Its application characteristics are demonstrated by the example of CBM wells in Ordos Basin. The interpretations of results show that the previous design gave the single rods a larger diameter and the top rods in the string a greater percent than the proposed method. The calculation should concern about inertial, vibration and friction forces to illustrate the elastic force waves travelling in the rod material with the speed of sound. The single string should be designed using fatigue endurance ratings due to asymmetric pulsating tension of rod loading; and the tapered string should involve a balanced design by setting the fatigue endurance at each section equal. A shorter stroke length gives a greater rod taper percentage and an increased load capacity results to an enhanced rod diameter. The rod diameter increases with the pump size and load capacity for the single string, and the rod taper percentage of the top rod strings increases with plunger diameter for the tapered string. The proposed research improves efficiency of the pumping system, assures good operating conditions, and reduces

  11. Dependence of control rod worth on fuel burnup

    Energy Technology Data Exchange (ETDEWEB)

    Savva, P., E-mail: savvapan@ipta.demokritos.g [NCSR ' DEMOKRITOS' , PoB 60228, 15310 Aghia Paraskevi (Greece); Varvayanni, M., E-mail: melina@ipta.demokritos.g [NCSR ' DEMOKRITOS' , PoB 60228, 15310 Aghia Paraskevi (Greece); Catsaros, N., E-mail: nicos@ipta.demokritos.g [NCSR ' DEMOKRITOS' , PoB 60228, 15310 Aghia Paraskevi (Greece)


    Research highlights: Diffusion and MC calculations for rod worth dependence on burnup and Xe in reactors. One-step rod withdrawal/insertion are used for rod worth estimation. The study showed that when Xe is present the rods worth is significantly reduced. Rod worth variation with burnup depends on rod position in core. Rod worth obtained with MC code is higher than that obtained from deterministic. - Abstract: One important parameter in the design and the analysis of a nuclear reactor core is the reactivity worth of the control rods, i.e. their efficiency to absorb excess reactivity. The control rod worth is affected by parameters such as the fuel burnup in the rod vicinity, the Xe concentration in the core, the operational time of the rod and its position in the core. In the present work, two different computational approaches, a deterministic and a stochastic one, were used for the determination of the rods worth dependence on the fuel burnup level and the Xe concentration level in a conceptual, symmetric reactor core, based on the MTR fuel assemblies used in the Greek Research Reactor (GRR-1). For the deterministic approach the neutronics code system composed by the SCALE modules NITAWL and XSDRN and the diffusion code CITATION was used, while for the stochastic one the Monte Carlo code TRIPOLI was applied. The study showed that when Xe is present in the core, the rods worth is significantly reduced, while the rod worth variation with increasing burnup depends on the rods position in the core grid. The rod worth obtained with the use of the Monte Carlo code is higher than the one obtained from the deterministic code.

  12. Distributed Mode Filtering Rod Fiber Amplifier With Improved Mode Stability

    DEFF Research Database (Denmark)

    Laurila, Marko; Alkeskjold, Thomas Tanggaard; Broeng, Jes


    We report 216W of average output power from a photonic crystal rod fiber amplifier. We demonstrate 44% power improvement before onset of the mode instability by operating the rod fiber in a leaky guiding regime.......We report 216W of average output power from a photonic crystal rod fiber amplifier. We demonstrate 44% power improvement before onset of the mode instability by operating the rod fiber in a leaky guiding regime....

  13. Sucker rod string design of the pumping systems

    Directory of Open Access Journals (Sweden)

    Chun Hua Liu


    Full Text Available The existing design of sucker rod string mainly focuses on the simplifying assumptions that rod string was exposed to simple tension loading. And its goal was to have equal modified stress at the top of each taper. The improved rod design was to have the same degree of safety at each section, and it used a dynamic force distribution that was proportional along the whole string. However, the available procedures did not provide the desired accuracy of its pertinent analysis, and the operators could not identify the specific phenomena that occur in CBM wells. In this paper, the mathematical models of rod loads and string length were developed based on the cyclic nature of rod string loading; the fatigue endurance method is used to design the single rod string; and the tapered rod string is designed to have an equal equivalent stress at the top of each section. Its application characteristics are demonstrated by the example of CBM wells in Ordos Basin. The interpretations of results show that the previous design gave the single rods a larger diameter and the top rods in the string a greater percent than the proposed method. The calculation should concern about inertial, vibration and friction forces to illustrate the elastic force waves travelling in the rod material with the speed of sound. The single string should be designed using fatigue endurance ratings due to asymmetric pulsating tension of rod loading; and the tapered string should involve a balanced design by setting the fatigue endurance at each section equal. A shorter stroke length gives a greater rod taper percentage and an increased load capacity results to an enhanced rod diameter. The rod diameter increases with the pump size and load capacity for the single string, and the rod taper percentage of the top rod strings increases with plunger diameter for the tapered string. The proposed research improves efficiency of the pumping system, assures good operating conditions, and reduces

  14. [Bundle-branch block depending on the heart rate]. (United States)

    Apostolov, L


    Five patients are reported, admitted to the hospital, with diseases predominantly of the cardio-vascular system. During the electrocardiographic examinations bundle branch block was established, depending on heart rate. It fluctuated within the physiological limits from 50 to 90/min. In three of the patients, the bundle branch block appeared with the quickening of the heart rate (tachycardia-depending bundle branch block) and in two of the patients--the bundle branch block appeared during the slowing down of the heart action and disappeared with its quickening (bradicardia-depending bundle branch block). A brief literature review is presented and attention is paid to the possible diagnostic errors and the treatment mode of those patients with cardiac tonic and antiarrhythmic medicaments.

  15. Bundles over Quantum RealWeighted Projective Spaces

    Directory of Open Access Journals (Sweden)

    Tomasz Brzeziński


    Full Text Available The algebraic approach to bundles in non-commutative geometry and the definition of quantum real weighted projective spaces are reviewed. Principal U(1-bundles over quantum real weighted projective spaces are constructed. As the spaces in question fall into two separate classes, the negative or odd class that generalises quantum real projective planes and the positive or even class that generalises the quantum disc, so do the constructed principal bundles. In the negative case the principal bundle is proven to be non-trivial and associated projective modules are described. In the positive case the principal bundles turn out to be trivial, and so all the associated modules are free. It is also shown that the circle (coactions on the quantum Seifert manifold that define quantum real weighted projective spaces are almost free.

  16. Artificial ciliary bundles with nano fiber tip links

    CERN Document Server

    Asadnia, Mohsen; Miao, Jianmin; Triantafyllou, Michael


    Mechanosensory ciliary bundles in fishes are the inspiration for carefully engineered artificial flow sensors. We report the development of a new class of ultrasensitive MEMS flow sensors that mimic the intricate morphology of the ciliary bundles, including the stereocilia, tip links, and the cupula, and thereby achieve threshold detection limits that match the biological example. An artificial ciliary bundle is achieved by fabricating closely-spaced arrays of polymer micro-pillars with gradiating heights. Tip links that form the fundamental sensing elements are realized through electrospinning aligned PVDF piezoelectric nano-fibers that link the distal tips of the polymer cilia. An optimized synthesis of hyaluronic acid-methacrylic anhydride hydrogel that results in properties close to the biological cupula, together with drop-casting method are used to form the artificial cupula that encapsulates the ciliary bundle. In testing, fluid drag force causes the ciliary bundle to slide, stretching the flexible nan...

  17. Superconductivity in an Inhomogeneous Bundle of Metallic and Semiconducting Nanotubes

    Directory of Open Access Journals (Sweden)

    Ilya Grigorenko


    Full Text Available Using Bogoliubov-de Gennes formalism for inhomogeneous systems, we have studied superconducting properties of a bundle of packed carbon nanotubes, making a triangular lattice in the bundle's transverse cross-section. The bundle consists of a mixture of metallic and doped semiconducting nanotubes, which have different critical transition temperatures. We investigate how a spatially averaged superconducting order parameter and the critical transition temperature depend on the fraction of the doped semiconducting carbon nanotubes in the bundle. Our simulations suggest that the superconductivity in the bundle will be suppressed when the fraction of the doped semiconducting carbon nanotubes will be less than 0.5, which is the percolation threshold for a two-dimensional triangular lattice.

  18. Evaluation of the Effect of Tube Pitch and Surface Alterations on Temperature Field at Sprinkled Tube Bundle

    Directory of Open Access Journals (Sweden)

    Kracík Petr


    Full Text Available Water flowing on a sprinkled tube bundle forms three basic modes: It is the Droplet mode (liquid drips from one tube to another, the Jet mode (with an increasing flow rate droplets merge into a column and the Membrane (Sheet mode (with further increasing of falling film liquid flow rate columns merge and create sheets between the tubes. With sufficient flow rate sheets merge at this state and the tube bundle is completely covered by a thin liquid film. There are several factors influencing the individual mode types as well as heat transfer. Beside the above mentioned falling film liquid flow rate they are for instance tube diameters, tube pitches in a tube bundle or a physical condition of a falling film liquid. This paper presents a summary of data measured at atmospheric pressure at a tube bundle consisting of copper tubes of 12 milimeters diameter and of the studied tube length one meter. The tubes are positioned horizontally one above another with the tested pitches of 15, 20, 25 and 30 mm and there is a distribution tube placed above them with water flowing out. The thermal gradient of 15–40 has been tested with all pitches where the falling film liquid’s temperature at the inlet of the distribution tube was 15 °C. The liquid was heated during the flow through the exchanger and the temperature of the sprinkled (heater liquid at the inlet of the exchanger with a constant flow rate about 7.2 litres per minute was 40 °C. The tested flow of the falling film liquid ranged from 1.0 to 13.0 litres per minute. Sequences of 180 exposures have been recorded in partial flow rate stages by thermographic camera with record frequency of 30 Hz which were consequently assessed using the Matlab programme. This paper presents results achieved at the above mentioned pitches and at three types of tube bundle surfaces.


    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, Kostadin [Pennsylvania State University, University Park; Jessee, Matthew Anderson [ORNL


    The discharge rod internal pressure (RIP) and cladding hoop stress (CHS) distributions are quantified forWatts BarNuclearUnit 1 (WBN1) fuel rods by modeling core cycle design data, intercycle assembly movements, operation data (including modeling significant trips and downpowers), and as-built fuel enrichments and densities of each fuel rod in FRAPCON-3.5. An alternate model for the amount of helium released from zirconium diboride (ZrB2) integral fuel burnable absorber (IFBA) layers is derived and applied to FRAPCON output data to quantify the RIP and CHS for these fuel rods. SCALE/Polaris is used to quantify fuel rod-specific spectral quantities and the amount of gaseous fission products produced in the fuel for use in FRAPCON inputs. Fuel rods with ZrB2 IFBA layers (i.e., IFBA rods) are determined to have RIP predictions that are elevated when compared to fuel rod without IFBA layers (i.e., standard rods) despite the fact that IFBA rods often have reduced fill pressures and annular fuel blankets. Cumulative distribution functions (CDFs) are prepared from the distribution of RIP predictions for all standard and IFBA rods. The provided CDFs allow for the determination of the portion of WBN1 fuel rods that exceed a specified RIP limit. Lastly, improvements to the computational methodology of FRAPCON are proposed.

  20. Measurement of the Speed of Sound in a Metal Rod. (United States)

    Mak, Se-yuen; Ng, Yee-kong; Wu, Kam-wah


    Suggests two improved methods to measure the speed of sound in a metal rod. One employs a fast timer to measure the time required for a compression pulse to travel along the rod from end to end, and a second uses a microphone to measure the frequency of the fundamental mode of a freely suspending singing rod. (Author/ASK)

  1. 77 FR 1504 - Stainless Steel Wire Rod From India (United States)


    ... COMMISSION Stainless Steel Wire Rod From India Determination On the basis of the record \\1\\ developed in the... antidumping duty order on stainless steel wire rod From India would be likely to lead to continuation or... contained in USITC Publication 4300 (January 2012), entitled Stainless Steel Wire Rod From India...

  2. Method and device for tensile testing of cable bundles (United States)

    Robertson, Lawrence M; Ardelean, Emil V; Goodding, James C; Babuska, Vit


    A standard tensile test device is improved to accurately measure the mechanical properties of stranded cables, ropes, and other composite structures wherein a witness is attached to the top and bottom mounting blocks holding the cable under test. The witness is comprised of two parts: a top and a bottom rod of similar diameter with the bottom rod having a smaller diameter stem on its upper end and the top rod having a hollow opening in its lower end into which the stem fits forming a witness joint. A small gap is present between the top rod and the larger diameter portion of the bottom rod. A standard extensometer is attached to the top and bottom rods of the witness spanning this small witness gap. When a force is applied to separate the mounting blocks, the gap in the witness expands the same length that the entire test specimen is stretched.

  3. Framework for shape analysis of white matter fiber bundles. (United States)

    Glozman, Tanya; Bruckert, Lisa; Pestilli, Franco; Yecies, Derek W; Guibas, Leonidas J; Yeom, Kristen W


    Diffusion imaging coupled with tractography algorithms allows researchers to image human white matter fiber bundles in-vivo. These bundles are three-dimensional structures with shapes that change over time during the course of development as well as in pathologic states. While most studies on white matter variability focus on analysis of tissue properties estimated from the diffusion data, e.g. fractional anisotropy, the shape variability of white matter fiber bundle is much less explored. In this paper, we present a set of tools for shape analysis of white matter fiber bundles, namely: (1) a concise geometric model of bundle shapes; (2) a method for bundle registration between subjects; (3) a method for deformation estimation. Our framework is useful for analysis of shape variability in white matter fiber bundles. We demonstrate our framework by applying our methods on two datasets: one consisting of data for 6 normal adults and another consisting of data for 38 normal children of age 11 days to 8.5 years. We suggest a robust and reproducible method to measure changes in the shape of white matter fiber bundles. We demonstrate how this method can be used to create a model to assess age-dependent changes in the shape of specific fiber bundles. We derive such models for an ensemble of white matter fiber bundles on our pediatric dataset and show that our results agree with normative human head and brain growth data. Creating these models for a large pediatric longitudinal dataset may improve understanding of both normal development and pathologic states and propose novel parameters for the examination of the pediatric brain. Copyright © 2017 Elsevier Inc. All rights reserved.

  4. Bundling of elastic filaments induced by hydrodynamic interactions (United States)

    Man, Yi; Page, William; Poole, Robert J.; Lauga, Eric


    Peritrichous bacteria swim in viscous fluids by rotating multiple helical flagellar filaments. As the bacterium swims forward, all its flagella rotate in synchrony behind the cell in a tight helical bundle. When the bacterium changes its direction, the flagellar filaments unbundle and randomly reorient the cell for a short period of time before returning to their bundled state and resuming swimming. This rapid bundling and unbundling is, at its heart, a mechanical process whereby hydrodynamic interactions balance with elasticity to determine the time-varying deformation of the filaments. Inspired by this biophysical problem, we present in this paper what is perhaps the simplest model of bundling whereby two or more straight elastic filaments immersed in a viscous fluid rotate about their centerline, inducing rotational flows which tend to bend the filaments around each other. We derive an integrodifferential equation governing the shape of the filaments resulting from mechanical balance in a viscous fluid at low Reynolds number. We show that such equation may be evaluated asymptotically analytically in the long-wavelength limit, leading to a local partial differential equation governed by a single dimensionless bundling number. A numerical study of the dynamics predicted by the model reveals the presence of two configuration instabilities with increasing bundling numbers: first to a crossing state where filaments touch at one point and then to a bundled state where filaments wrap along each other in a helical fashion. We also consider the case of multiple filaments and the unbundling dynamics. We next provide an intuitive physical model for the crossing instability and show that it may be used to predict analytically its threshold and adapted to address the transition to a bundling state. We then use a macroscale experimental implementation of the two-filament configuration in order to validate our theoretical predictions and obtain excellent agreement. This long

  5. Restriction of Preferences to the Set of Consumption Bundles, In a Model with Production and Consumption Bundles

    NARCIS (Netherlands)

    Schalk, S.


    In contrast to the neo-classical theory of Arrow and Debreu, a model of a private ownership economy is presented, in which production and consumption bundles are treated separately. Each of the two types of bundles is assumed to establish a con- vex cone. Production technologies can convert

  6. Single-Bundle Versus Double-Bundle Reconstruction for Anterior Cruciate Ligament Rupture: A Meta-Analysis-Does Anatomy Matter?

    NARCIS (Netherlands)

    Eck, Carola F. Van; Kopf, Sebastian; Irrgang, James J.; Blankevoort, Leendert; Bhandari, Mohit; Fu, Freddie H.; Poolman, Rudolf W.


    Purpose: To determine whether double-bundle anterior cruciate ligament reconstruction leads to better restoration of anterior and rotational laxity and range of motion than single-bundle reconstruction. Methods: A search was performed in the Medline, Embase, CINAHL, and Cochrane databases. All

  7. Cost-effectiveness of a central venous catheter care bundle.

    Directory of Open Access Journals (Sweden)

    Kate A Halton

    Full Text Available BACKGROUND: A bundled approach to central venous catheter care is currently being promoted as an effective way of preventing catheter-related bloodstream infection (CR-BSI. Consumables used in the bundled approach are relatively inexpensive which may lead to the conclusion that the bundle is cost-effective. However, this fails to consider the nontrivial costs of the monitoring and education activities required to implement the bundle, or that alternative strategies are available to prevent CR-BSI. We evaluated the cost-effectiveness of a bundle to prevent CR-BSI in Australian intensive care patients. METHODS AND FINDINGS: A Markov decision model was used to evaluate the cost-effectiveness of the bundle relative to remaining with current practice (a non-bundled approach to catheter care and uncoated catheters, or use of antimicrobial catheters. We assumed the bundle reduced relative risk of CR-BSI to 0.34. Given uncertainty about the cost of the bundle, threshold analyses were used to determine the maximum cost at which the bundle remained cost-effective relative to the other approaches to infection control. Sensitivity analyses explored how this threshold alters under different assumptions about the economic value placed on bed-days and health benefits gained by preventing infection. If clinicians are prepared to use antimicrobial catheters, the bundle is cost-effective if national 18-month implementation costs are below $1.1 million. If antimicrobial catheters are not an option the bundle must cost less than $4.3 million. If decision makers are only interested in obtaining cash-savings for the unit, and place no economic value on either the bed-days or the health benefits gained through preventing infection, these cost thresholds are reduced by two-thirds. CONCLUSIONS: A catheter care bundle has the potential to be cost-effective in the Australian intensive care setting. Rather than anticipating cash-savings from this intervention, decision

  8. On the Vortex Sound from Rotating Rods (United States)

    Yudin, E. Y.


    The motion of different bodies imersed in liquid or gaseous media is accompanied by characteristic sound which is excited by the formation of unstable surfaces of separation behind the body, usually disintegrating into a system of discrete vortices(such as the Karman vortex street due to the flow about an infintely long rod, etc.).In the noise from fans,pumps,and similar machtnery, vortexnQif3eI?Yequently predominates. The purpose of this work is to elucidate certain questions of the dependence ofthis sound upon the aerodynamic parameters and the tip speed of the rotating rods,or blades. Although scme material is given below,insufficientto calculate the first rough approximation to the solution of this question,such as the mechanics of vortex formation,never the less certain conclusions maybe found of practical application for the reduction of noise from rotating blades.

  9. Composites reinforcement by rods a SAS study

    CERN Document Server

    Urban, V; Pyckhout-Hintzen, W; Richter, D; Straube, E


    The mechanical properties of composites are governed by size, shape and dispersion degree of so-called reinforcing particles. Polymeric fillers based on thermodynamically driven microphase separation of block copolymers offer the opportunity to study a model system of controlled rod-like filler particles. We chose a triblock copolymer (PBPSPB) and carried out SAS measurements with both X-rays and neutrons, in order to characterize separately the hard phase and the cross-linked PB matrix. The properties of the material depend strongly on the way that stress is carried and transferred between the soft matrix and the hard fibers. The failure of the strain-amplification concept and the change of topological contributions to the free energy and scattering factor have to be addressed. In this respect the composite shows a similarity to a two-network system, i.e. interpenetrating rubber and rod-like filler networks. (orig.)

  10. Rod Driven Frequency Entrainment and Resonance Phenomena

    Directory of Open Access Journals (Sweden)

    Christina Salchow


    Full Text Available A controversy exists on photic driving in the human visual cortex evoked by intermittent photic stimulation. Frequency entrainment and resonance phenomena are reported for frequencies higher than 12 Hz in some studies while missing in others. We hypothesized that this might be due to different experimental conditions, since both high and low intensity light stimulation were used. However, most studies do not report radiometric measurements, which makes it impossible to categorize the stimulation according to photopic, mesopic, and scotopic vision. Low intensity light stimulation might lead to scotopic vision, where rod perception dominates. In this study, we investigated photic driving for rod-dominated visual input under scotopic conditions. Twelve healthy volunteers were stimulated with low intensity light flashes at 20 stimulation frequencies, leading to rod activation only. The frequencies were multiples of the individual alpha frequency (α of each volunteer in the range from 0.40–2.30*α. 306-channel whole head magnetoencephalography recordings were analyzed in time, frequency, and spatiotemporal domains with the Topographic Matching Pursuit algorithm. We found resonance phenomena and frequency entrainment for stimulations at or close to the individual alpha frequency (0.90–1.10*α and half of the alpha frequency (0.40–0.55*α. No signs of resonance and frequency entrainment phenomena were revealed around 2.00*α. Instead, on-responses at the beginning and off-responses at the end of each stimulation train were observed for the first time in a photic driving experiment at frequencies of 1.30–2.30*α, indicating that the flicker fusion threshold was reached. All results, the resonance and entrainment as well as the fusion effects, provide evidence for rod-dominated photic driving in the visual cortex.


    Young, J.N.


    An electromagnetic device for moving an object in a linear path by increments is described. The device is specifically adapted for moving a neutron absorbing control rod into and out of the core of a reactor and consists essentially of an extension member made of magnetic material connected to one end of the control rod and mechanically flexible to grip the walls of a sleeve member when flexed, a magnetic sleeve member coaxial with and slidable between limit stops along the flexible extension, electromagnetic coils substantially centrally located with respect to the flexible extension to flex the extension member into gripping engagement with the sleeve member when ener gized, moving electromagnets at each end of the sleeve to attract the sleeve when energized, and a second gripping electromagnet positioned along the flexible extension at a distance from the previously mentioned electromagnets for gripping the extension member when energized. In use, the second gripping electromagnet is deenergized, the first gripping electromagnet is energized to fix the extension member in the sleeve, and one of the moving electromagnets is energized to attract the sleeve member toward it, thereby moving the control rod.

  12. Lasing in optimized two-dimensional iron-nail-shaped rod photonic crystals

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Soon-Yong; Moon, Seul-Ki; Yang, Jin-Kyu, E-mail: [Department of Optical Engineering, Kongju National University, Cheonan 330-717 (Korea, Republic of); Choi, Jae-Hyuck; Jang, Se-Hwan; Jeong, Kwang-Yong; Park, Hong-Gyu [Department of Physics, Korea University, Seoul 136-713 (Korea, Republic of)


    We demonstrated lasing at the Γ-point band-edge (BE) modes in optimized two-dimensional iron-nail-shaped rod photonic crystals by optical pulse pumping at room temperature. As the radius of the rod increased quadratically toward the edge of the pattern, the quality factor of the Γ-point BE mode increased up to three times, and the modal volume decreased to 56% compared with the values of the original Γ-point BE mode because of the reduction of the optical loss in the horizontal direction. Single-mode lasing from an optimized iron-nail-shaped rod array with an InGaAsP multiple quantum well embedded in the nail heads was observed at a low threshold pump power of 160 μW. Real-image-based numerical simulations showed that the lasing actions originated from the optimized Γ-point BE mode and agreed well with the measurement results, including the lasing polarization, wavelength, and near-field image.


    Directory of Open Access Journals (Sweden)

    Paolo Macini


    Full Text Available This paper underlines the importance of the correct drill bit application in horizontal wells. Afler the analysis of the peculiarities of horizontal wells and drainholes drilling techniques, advantages and disadvantages of the application of both roller cone and fixed cutters drill bits have been discussed. Also, a review of the potential specific featuries useful for a correct drill bit selection in horizontal small diameter holes has been highlighted. Drill bits for these special applications, whose importance is quickly increasing nowadays, should be characterised by a design capable to deliver a good penetration rate low WOB, and, at the same time, be able to withstand high RPM without premature cutting structure failure and undergauge. Formation properties will also determine the cutting structure type and the eventual specific features for additional gauge and shoulder protection.

  14. Nuclear component horizontal seismic restraint (United States)

    Snyder, Glenn J.


    A nuclear component horizontal seismic restraint. Small gaps limit horizontal displacement of components during a seismic occurrence and therefore reduce dynamic loadings on the free lower end. The reactor vessel and reactor guard vessel use thicker section roll-forged rings welded between the vessel straight shell sections and the bottom hemispherical head sections. The inside of the reactor guard vessel ring forging contains local vertical dovetail slots and upper ledge pockets to mount and retain field fitted and installed blocks. As an option, the horizontal displacement of the reactor vessel core support cone can be limited by including shop fitted/installed local blocks in opposing alignment with the reactor vessel forged ring. Beams embedded in the wall of the reactor building protrude into apertures in the thermal insulation shell adjacent the reactor guard vessel ring and have motion limit blocks attached thereto to provide to a predetermined clearance between the blocks and reactor guard vessel ring.

  15. Nurses’ Perceptions of Horizontal Violence

    Directory of Open Access Journals (Sweden)

    Rosemary Taylor


    Full Text Available In this article, I describe a study exploring horizontal violence and nurses’ perceptions of the phenomenon within the context of two 28-bed inpatient hospital units. The purpose of the study was to develop a clearer understanding of horizontal violence, incorporating observation and inquiry to identify the language nurses use to describe their experiences and factors in the nursing work environment that may perpetuate the phenomenon. Observation, review and analysis of policies, and interviews with staff were completed between June and November 2012. Thematic analysis resulted in five themes: (a behaviors are minimized and not recognized, (b fear inhibits all reporting, (c avoidance and isolation are coping strategies, (d lack of respect and support, and (e organizational chaos. The findings suggest future interventions must address a range of factors that perpetuate horizontal violence within the nursing work environment with consideration for the embeddedness and complexity of the phenomenon.

  16. Bundling Actin Filaments From Membranes: Some Novel Players

    Directory of Open Access Journals (Sweden)

    Clément eThomas


    Full Text Available Progress in live-cell imaging of the cytoskeleton has significantly extended our knowledge about the organization and dynamics of actin filaments near the plasma membrane of plant cells. Noticeably, two populations of filamentous structures can be distinguished. On the one hand, fine actin filaments which exhibit an extremely dynamic behavior basically characterized by fast polymerization and prolific severing events, a process referred to as actin stochastic dynamics. On the other hand, thick actin bundles which are composed of several filaments and which are comparatively more stable although they constantly remodel as well. There is evidence that the actin cytoskeleton plays critical roles in trafficking and signaling at both the cell cortex and organelle periphery but the exact contribution of actin bundles remains unclear. A common view is that actin bundles provide the long-distance tracks used by myosin motors to deliver their cargo to growing regions and accordingly play a particularly important role in cell polarization. However, several studies support that actin bundles are more than simple passive highways and display multiple and dynamic roles in the regulation of many processes, such as cell elongation, polar auxin transport, stomatal and chloroplast movement, and defense against pathogens. The list of identified plant actin-bundling proteins is ever expanding, supporting that plant cells shape structurally and functionally different actin bundles. Here I review the most recently characterized actin-bundling proteins, with a particular focus on those potentially relevant to membrane trafficking and/or signaling.

  17. The orphan nuclear hormone receptor ERRβ controls rod photoreceptor survival (United States)

    Onishi, Akishi; Peng, Guang-Hua; Poth, Erin M.; Lee, Daniel A.; Chen, Jichao; Alexis, Uel; de Melo, Jimmy; Chen, Shiming; Blackshaw, Seth


    Mutation of rod photoreceptor-enriched transcription factors is a major cause of inherited blindness. We identified the orphan nuclear hormone receptor estrogen-related receptor β (ERRβ) as selectively expressed in rod photoreceptors. Overexpression of ERRβ induces expression of rod-specific genes in retinas of wild-type as well as Nrl−/− mice, which lack rod photoreceptors. Mutation of ERRβ results in dysfunction and degeneration of rods, whereas inverse agonists of ERRβ trigger rapid rod degeneration, which is rescued by constitutively active mutants of ERRβ. ERRβ coordinates expression of multiple genes that are rate-limiting regulators of ATP generation and consumption in photoreceptors. Furthermore, enhancing ERRβ activity rescues photoreceptor defects that result from loss of the photoreceptor-specific transcription factor Crx. Our findings demonstrate that ERRβ is a critical regulator of rod photoreceptor function and survival, and suggest that ERRβ agonists may be useful in the treatment of certain retinal dystrophies. PMID:20534447

  18. Speckle Imaging Over Horizontal Paths

    Energy Technology Data Exchange (ETDEWEB)

    Carrano, C J


    Atmospheric aberrations reduce the resolution and contrast in surveillance images recorded over horizontal or slant paths. This paper describes our recent horizontal and slant path imaging experiments of extended scenes as well as the results obtained using speckle imaging. The experiments were performed with an 8-inch diameter telescope placed on either a rooftop or hillside and cover ranges of interest from 0.5 km up to 10 km. The scenery includes resolution targets, people, vehicles, and other structures. The improvement in image quality using speckle imaging is dramatic in many cases, and depends significantly upon the atmospheric conditions. We quantify resolution improvement through modulation transfer function measurement comparisons.

  19. Aerosol retention in the flooded steam generator bundle during SGTR

    Energy Technology Data Exchange (ETDEWEB)

    Lind, Terttaliisa, E-mail: terttaliisa.lind@psi.c [Paul Scherrer Institut, Department of Nuclear Energy and Safety, 5232 Villigen (Switzerland); Dehbi, Abdel; Guentay, Salih [Paul Scherrer Institut, Department of Nuclear Energy and Safety, 5232 Villigen (Switzerland)


    Research highlights: High retention of aerosol particles in a steam generator bundle flooded with water. Increasing particle inertia, i.e., particle size and velocity, increases retention. Much higher retention of aerosol particles in the steam generator bundle flooded with water than in a dry bundle. Much higher retention of aerosol particles in the steam generator bundle than in a bare pool. Bare pool models have to be adapted to be applicable for flooded bundles. - Abstract: A steam generator tube rupture in a pressurized water reactor may cause accidental release of radioactive particles into the environment. Its specific significance is in its potential to bypass the containment thereby providing a direct pathway of the radioactivity from the primary circuit to the environment. Under certain severe accident scenarios, the steam generator bundle may be flooded with water. In addition, some severe accident management procedures are designed to minimize the release of radioactivity into the environment by flooding the defective steam generator secondary side with water when the steam generator has dried out. To extend our understanding of the particle retention phenomena in the flooded steam generator bundle, tests were conducted in the ARTIST and ARTIST II programs to determine the effect of different parameters on particle retention. The effects of particle type (spherical or agglomerate), particle size, gas mass flow rate, and the break submergence on particle retention were investigated. Results can be summarized as follows: increasing particle inertia was found to increase retention in the flooded bundle. Particle shape, i.e., agglomerate or spherical structure, did not affect retention significantly. Even with a very low submergence, 0.3 m above the tube break, significant aerosol retention took place underlining the importance of the jet-bundle interactions close to the tube break. Droplets were entrained from the water surface with high gas flow rates

  20. Between a Map and a Data Rod (United States)

    Teng, W. L.; Rui, H.; Strub, R. F.; Vollmer, B.


    A "Digital Divide" has long stood between how NASA and other satellite-derived data are typically archived (time-step arrays or "maps") and how hydrology and other point-time series oriented communities prefer to access those data. In essence, the desired method of data access is orthogonal to the way the data are archived. Our approach to bridging the Divide is part of a larger NASA-supported "data rods" project to enhance access to and use of NASA and other data by the Consortium of Universities for the Advancement of Hydrologic Science, Inc. (CUAHSI) Hydrologic Information System (HIS) and the larger hydrology community. Our main objective was to determine a way to reorganize data that is optimal for these communities. Two related objectives were to optimally reorganize data in a way that (1) is operational and fits in and leverages the existing Goddard Earth Sciences Data and Information Services Center (GES DISC) operational environment and (2) addresses the scaling up of data sets available as time series from those archived at the GES DISC to potentially include those from other Earth Observing System Data and Information System (EOSDIS) data archives. Through several prototype efforts and lessons learned, we arrived at a non-database solution that satisfied our objectives/constraints. We describe, in this presentation, how we implemented the operational production of pre-generated data rods and, considering the tradeoffs between length of time series (or number of time steps), resources needed, and performance, how we implemented the operational production of on-the-fly ("virtual") data rods. For the virtual data rods, we leveraged a number of existing resources, including the NASA Giovanni Cache and NetCDF Operators (NCO) and used data cubes processed in parallel. Our current benchmark performance for virtual generation of data rods is about a year's worth of time series for hourly data (~9,000 time steps) in ~90 seconds. Our approach is a specific

  1. Outcomes of support rod usage in loop stoma formation. (United States)

    Whiteley, Ian; Russell, Michael; Nassar, Natasha; Gladman, Marc A


    Traditionally, support rods have been used when creating loop stomas in the hope of preventing retraction. However, their effectiveness has not been clearly established. This study aimed to investigate the rate of stoma rod usage and its impact on stoma retraction and complication rates. A prospective cohort of 515 consecutive patients who underwent loop ileostomy/colostomy formation at a tertiary referral colorectal unit in Sydney, Australia were studied. Mortality and unplanned return to theatre rates were calculated. The primary outcome measure of interest was stoma retraction, occurring within 30 days of surgery. Secondary outcome measures included early stoma complications. The 10-year temporal trends for rod usage, stoma retraction, and complications were examined. Mortality occurred in 23 patients (4.1 %) and unplanned return to theatre in 4 patients (0.8 %). Stoma retraction occurred in four patients (0.78 %), all without rods. However, the rate of retraction was similar, irrespective of whether rods were used (P = 0.12). There was a significant decline in the use of rods during the study period (P stoma retraction rates. Early complications occurred in 94/432 patients (21.8 %) and were more likely to occur in patients with rods (64/223 versus 30/209 without rods, P Stoma retraction is a rare complication and its incidence is not significantly affected by the use of support rods. Further, complications are common post-operatively, and the rate appears higher when rods are used. The routine use of rods warrants judicious application. WHAT DOES THIS PAPER ADD TO THE LITERATURE?: It remains unclear whether support rods prevent stoma retraction. This study, the largest to date, confirms that stoma retraction is a rare complication and is not significantly affected by the use of rods. Consequently, routine rod usage cannot be recommended, particularly as it is associated with increased stoma complications.

  2. Dark-field illuminated reflectance fiber bundle endoscopic microscope (United States)

    Liu, Xuan; Huang, Yong; Kang, Jin U.


    We propose a reflectance fiber bundle microscope using a dark-field illumination configuration for applications in endoscopic medical imaging and diagnostics. Our experiment results show that dark-field illumination can effectively suppress strong specular reflection from the proximal end of the fiber bundle. We realized a lateral resolution of 4.4 μm using the dark-field illuminated fiber bundle configuration. To demonstrate the feasibility of using the system to study cell morphology, we obtained still and video images of two thyroid cancer cell lines. Our results clearly allow differentiation of different cancer cell types.

  3. Moduli of Parabolic Higgs Bundles and Atiyah Algebroids

    DEFF Research Database (Denmark)

    Logares, Marina; Martens, Johan


    In this paper we study the geometry of the moduli space of (non-strongly) parabolic Higgs bundles over a Riemann surface with marked points. We show that this space possesses a Poisson structure, extending the one on the dual of an Atiyah algebroid over the moduli space of parabolic vector bundles....... By considering the case of full flags, we get a Grothendieck–Springer resolution for all other flag types, in particular for the moduli spaces of twisted Higgs bundles, as studied by Markman and Bottacin and used in the recent work of Laumon–Ngô. We discuss the Hitchin system, and demonstrate that all...

  4. Characterization of dominant giant rod-shaped magnetotactic bacteria from a low tide zone of the China Sea (United States)

    Teng, Zhaojie; Zhang, Wenyan; Chen, Yiran; Pan, Hongmiao; Xiao, Tian; Wu, Long-Fei


    Magnetotactic bacteria are a group of Gram-negative bacteria that synthesize magnetic crystals, enabling them to navigate in relation to magnetic field lines. Morphologies of magnetotactic bacteria include spirillum, coccoid, rod, vibrio, and multicellular morphotypes. The coccid shape is generally the most abundant morphotype among magnetotactic bacteria. Here we describe a species of giant rod-shaped magnetotactic bacteria (designated QR-1) collected from sediment in the low tide zone of Huiquan Bay (Yellow Sea, China). This morphotype accounted for 90% of the magnetotactic bacteria collected, and the only taxonomic group which was detected in the sampling site. Microscopy analysis revealed that QR-1 cells averaged (6.71±1.03)×(1.54±0.20) μm in size, and contained in each cell 42-146 magnetosomes that are arranged in a bundle formed one to four chains along the long axis of the cell. The QR-1 cells displayed axial magnetotaxis with an average velocity of 70±28 μm/s. Transmission electron microscopy based analysis showed that QR-1 cells had two tufts of flagella at each end. Phylogenetic analysis of the 16S rRNA genes revealed that QR-1 together with three other rod-shaped uncultivated magnetotactic bacteria are clustered into a deep branch of Alphaproteobacteria.

  5. Conceptional design of test loop for FIV in fuel bundle

    Energy Technology Data Exchange (ETDEWEB)

    Sim, W. G.; Yang, J. S.; Kim, S. W. [Hannam Univ., Taejeon (Korea)


    It is urgent to develop the analytical model for the structural/mechanical integrity of fuel rod. In general, it is not easy to develop a pure analytical model. Occasionally, experimental results have been utilized for the model. Because of this reason, it is required to design proper test loop. Using the optimized test loop, with the optimized test loop, the dynamic behaviour of the rod will be evaluated and the critical flow velocity, which the rod loses the stability in, will be measured for the design of the rod. To verify the integrity of the fuel rod, it is required to evaluate the dynamic behaviour and the critical flow velocity with the test loop. The test results will be utilized to the design of the rod. Generally, the rod has a ground vibration due to turbulence in wide range of flow velocity and the amplitude of vibration becomes larger by the resonance, in a range of the velocity where occurs vortex. The rod loses stability in critical flow velocity caused by fluid-elastic instability. For the purpose of the present work to perform the conceptional design of the test loop, it is necessary (1) to understand the mechanism of the flow-induced vibration and the related experimental coefficients, (2) to evaluate the existing test loops for improving the loop with design parameters and (3) to decide the design specifications of the major equipments of the loop. 35 refs., 23 figs., 2 tabs. (Author)

  6. Texture development in Ti/Al filament wires produced by accumulative swaging and bundling

    Energy Technology Data Exchange (ETDEWEB)

    Eschke, A., E-mail: [Technische Universität Dresden, Institut für Strukturphysik, 01062 Dresden (Germany); Scharnweber, J.; Oertel, C.-G.; Skrotzki, W. [Technische Universität Dresden, Institut für Strukturphysik, 01062 Dresden (Germany); Marr, T.; Romberg, J. [Leibnizinstitut für Festkörper- und Werkstoffforschung Dresden, 01069 Dresden (Germany); Freudenberger, J. [Leibnizinstitut für Festkörper- und Werkstoffforschung Dresden, 01069 Dresden (Germany); Technische Universität Bergakademie Freiberg, Institut für Werkstoffwissenschaft, 09599 Freiberg (Germany); Schultz, L. [Leibnizinstitut für Festkörper- und Werkstoffforschung Dresden, 01069 Dresden (Germany); Technische Universität Dresden, Institut für Werkstoffwissenschaft, 01062 Dresden (Germany); Okulov, I.; Kühn, U. [Leibnizinstitut für Festkörper- und Werkstoffforschung Dresden, 01069 Dresden (Germany); Eckert, J. [Leibnizinstitut für Festkörper- und Werkstoffforschung Dresden, 01069 Dresden (Germany); Technische Universität Dresden, Institut für Werkstoffwissenschaft, 01062 Dresden (Germany)


    Mechanical properties of ultra-fine grained materials are interesting for advanced engineering applications. For producing ultra-fine grained microstructures, various top-down processes of severe plastic deformation like equal channel angular pressing, high pressure torsion and accumulative roll bonding are available. The evolution of texture with respect to deformation by an alternative severe plastic deformation process, called accumulative swaging and bundling, is shown for ultra-fine grained Ti/Al composite wires, suitable for structural applications because of their high specific strength. In this cyclic process, an aluminium rod is inserted into a titanium tube before being swaged with an areal reduction of 20% per pass to a true strain of 4.3. After cleaning and cutting the resulting composite wire into 37 pieces, these are stacked in hexagonal arrangement into another Ti tube of the initial dimension before deformation is continued. The local texture gradient of the accumulative swaging and bundling composites was studied using a X-ray microdiffraction system based on a D8 Discover (Bruker AXS GmbH) equipped with a microfocus X-ray tube Iμ S and an area detector VÅNTEC-2000. The results are discussed with respect to the grain refining deformation process starting from the initial texture measured by synchrotron and neutron diffraction, respectively. The local Al and Ti texture evolution is related to the deformation mode, which is similar to extrusion. As such, an Al〈111〉+〈100〉-double fibre and a Ti〈101{sup ¯}0〉-fibre emerge as the main texture components, each revealing gradients related to the deformation process. In particular, the local Al texture – being a function of both radial measurement position and deformation stage – can be correlated to material and process related issues like plastic flow and the superposition effect due to encapsulated filaments, respectively.

  7. Formation of bundle-shaped β-NaYF4 upconversion microtubes via Ostwald ripening. (United States)

    Gao, Dangli; Zhang, Xiangyu; Gao, Wei


    In this work, the uniform bundle-shaped microtubes composed of six half-pipes are synthesized for the first time in hydrothermal solutions via an intentional delayed phase transition pathway induced by Mn(2+) doping. The structural and kinetic factors that govern the phase and shape evolution of NaYF4 microcrystals have been carefully studied, and the influences of Mn(2+) to RE(3+) ratio, the amount of trisodium citrate, and the pH value in conjunction with the intrinsic character of RE(3+) ions on the phase and shape evolution are systematically discussed. It is found that the proper Mn(2+) to RE(3+) ratio is mainly responsible for delayed phase transition process and induces interior density gradient of solid aggregate for creating hollow bundle-shaped microtubes. While the amount of trisodium citrate and the pH value are the keys for the shape control of the NaYF4 microcrystals such as prismatic microtubes, prismatic short rods, thin plates, and particles. The up and downconversion emissions were obtained independent of whether α- or β-NaYF4:Er(3+)/Yb(3+) samples doped with Mn(2+), but the significant tuning of output color was only obtained in cube NaYF4 nanoparticles rather than in hexagonal microtubes via adjusting the amount of Mn(2+) ions. These spectral measurements and EDX analyses indicate that the distribution or concentration of Mn(2+) in hexagonal phase solid solution has changed, which supports Ostwald ripening growth mechanism and rules out agglomeration or oriented attachment growth mechanism. We designed crystal growth mode by simply addition of dopant may provide a versatile approach for fabricating a wide range of hollow nano/microcrystals and thus bring us a clearer understanding on the interaction between the dopant reagents and the nano/microcrystals.

  8. Sucker-rod pumping handbook production engineering fundamentals and long-stroke rod pumping

    CERN Document Server

    Takacs, Gabor


    Sucker-Rod Pumping Handbook presents the latest information on the most common form of production enhancement in today's oil industry, making up roughly two-thirds of the producing oilwell operations in the world. The book begins with an introduction to the main features of sucker rod pumping and an explanation and comparison of lift methods. It goes on to provide the technical and practical knowledge needed to introduce the new and practicing production engineer and operator to the equipment, technology, and applications required to maintain optimum operating conditions.

  9. Combustion of solid carbon rods in zero and normal gravity. Ph.D. Thesis - Toledo Univ., Ohio (United States)

    Spuckler, C. M.


    In order to investigate the mechanism of carbon combustion and to assess the importance of gravitational induced convection on the process, zero and normal gravity experiments were conducted in which spectroscopic carbon rods were resistance ignitied and burned in dry oxygen environments. In the zero-gravity drop tower tests, a blue flame surrounded the rod, showing that a gas phase reaction in which carbon monoxide was oxidized to carbon dioxide was taking place. The ratio of flame diameter to rod diameter was obtained as a function of time. It was found that this ratio was inversely proportional to both the oxygen pressure and the rod diameter. In the normal gravity tests, direct mass spectrometric sampling was used to measure gas phase concentrations. The gas sampling probe was positioned near the circumference of a horizontally mounted 0.615 cm diameter carbon rod, either at the top or at angles of 45 deg to 90 deg from the top, and yielded concentration profiles of CO2, CO, and O2 as a function of distance from the surface. The mechanism controlling the combustion process was found to change from chemical process control at the 90 deg and 45 deg probe positions to mass transfer control at the 0 deg probe position at the top of the rod. Under the experimental conditions used, carbon combustion was characterized by two surface reactions, 2C + O2 yields 2CO and CO2 + C yields 2CO, and a gas phase reaction, 2CO + O2 yields 2CO2.

  10. The ATLAS tile calorimeter ROD injector and multiplexer board

    Energy Technology Data Exchange (ETDEWEB)

    Valero, A., E-mail: alberto.valero@cern.c [Instituto de Fisica Corpuscular, Universidad de Valencia-CSIC, Paterna, 46071 Valencia (Spain); Castillo, V.; Ferrer, A. [Instituto de Fisica Corpuscular, Universidad de Valencia-CSIC, Paterna, 46071 Valencia (Spain); Gonzalez, V. [Departamento de Ingenieria electronica, Universidad de Valencia, Burjassot, 46100 Valencia (Spain); Hernandez, Y.; Higon, E. [Instituto de Fisica Corpuscular, Universidad de Valencia-CSIC, Paterna, 46071 Valencia (Spain); Sanchis, E. [Departamento de Ingenieria electronica, Universidad de Valencia, Burjassot, 46100 Valencia (Spain); Solans, C. [Instituto de Fisica Corpuscular, Universidad de Valencia-CSIC, Paterna, 46071 Valencia (Spain); Torres, J. [Departamento de Ingenieria electronica, Universidad de Valencia, Burjassot, 46100 Valencia (Spain); Valls, J.A. [Instituto de Fisica Corpuscular, Universidad de Valencia-CSIC, Paterna, 46071 Valencia (Spain)


    The ATLAS Tile Calorimeter is a sampling detector composed by cells made of iron-scintillator tiles. The calorimeter cell signals are digitized in the front-end electronics and transmitted to the Read-Out Drivers (RODs) at the first level trigger rate. The ROD receives triggered data from up to 9856 channels and provides the energy, phase and quality factor of the signals to the second level trigger. The back-end electronics is divided into four partitions containing eight RODs each. Therefore, a total of 32 RODs are used to process and transmit the data of the TileCal detector. In order to emulate the detector signals in the production and commissioning of ROD modules a board called ROD Injector and Multiplexer Board (RIMBO) was designed. In this paper, the RIMBO main functional blocks, PCB design and the different operation modes are described. It is described the crucial role of the board within the TileCal ROD test-bench in order to emulate the front-end electronics during the validation of ROD boards as well as during the evaluation of the ROD signal reconstruction algorithms. Finally, qualification and performance results for the injection operation mode obtained during the Tile Calorimeter ROD production tests are presented.

  11. Simulation of finite size effects of the fiber bundle model (United States)

    Hao, Da-Peng; Tang, Gang; Xun, Zhi-Peng; Xia, Hui; Han, Kui


    In theory, the macroscopic fracture of materials should correspond with the thermodynamic limit of the fiber bundle model. However, the simulation of a fiber bundle model with an infinite size is unrealistic. To study the finite size effects of the fiber bundle model, fiber bundle models of various size are simulated in detail. The effects of system size on the constitutive behavior, critical stress, maximum avalanche size, avalanche size distribution, and increased step number of external load are explored. The simulation results imply that there is no feature size or cut size for macroscopic mechanical and statistical properties of the model. The constitutive curves near the macroscopic failure for various system size can collapse well with a simple scaling relationship. Simultaneously, the introduction of a simple extrapolation method facilitates the acquisition of more accurate simulation results in a large-limit system, which is better for comparison with theoretical results.

  12. Improved Conjugate Gradient Bundle Adjustment of Dunhuang Wall Painting Images (United States)

    Hu, K.; Huang, X.; You, H.


    Bundle adjustment with additional parameters is identified as a critical step for precise orthoimage generation and 3D reconstruction of Dunhuang wall paintings. Due to the introduction of self-calibration parameters and quasi-planar constraints, the structure of coefficient matrix of the reduced normal equation is banded-bordered, making the solving process of bundle adjustment complex. In this paper, Conjugate Gradient Bundle Adjustment (CGBA) method is deduced by calculus of variations. A preconditioning method based on improved incomplete Cholesky factorization is adopt to reduce the condition number of coefficient matrix, as well as to accelerate the iteration rate of CGBA. Both theoretical analysis and experimental results comparison with conventional method indicate that, the proposed method can effectively conquer the ill-conditioned problem of normal equation and improve the calculation efficiency of bundle adjustment with additional parameters considerably, while maintaining the actual accuracy.

  13. Bundles of Norms About Teen Sex and Pregnancy. (United States)

    Mollborn, Stefanie; Sennott, Christie


    Teen pregnancy is a cultural battleground in struggles over morality, education, and family. At its heart are norms about teen sex, contraception, pregnancy, and abortion. Analyzing 57 interviews with college students, we found that "bundles" of related norms shaped the messages teens hear. Teens did not think their communities encouraged teen sex or pregnancy, but normative messages differed greatly, with either moral or practical rationalizations. Teens readily identified multiple norms intended to regulate teen sex, contraception, abortion, childbearing, and the sanctioning of teen parents. Beyond influencing teens' behavior, norms shaped teenagers' public portrayals and post hoc justifications of their behavior. Although norm bundles are complex to measure, participants could summarize them succinctly. These bundles and their conflicting behavioral prescriptions create space for human agency in negotiating normative pressures. The norm bundles concept has implications for teen pregnancy prevention policies and can help revitalize social norms for understanding health behaviors. © The Author(s) 2014.

  14. Algebraic Frobenius splitting of cotangent bundles of flag varieties

    National Research Council Canada - National Science Library

    Hague, Chuck


    Following the program of algebraic Frobenius splitting begun by Kumar and Littelmann, we use representation-theoretic techniques to construct a Frobenius splitting of the cotangent bundle of the flag...

  15. Design and synthesis of DNA four-helix bundles. (United States)

    Rangnekar, Abhijit; Gothelf, Kurt V; LaBean, Thomas H


    The field of DNA nanotechnology has evolved significantly in the past decade. Researchers have succeeded in synthesizing tile-based structures and using them to form periodic lattices in one, two and three dimensions. Origami-based structures have also been used to create nanoscale structures in two and three dimensions. Design and construction of DNA bundles with fixed circumference has added a new dimension to the field. Here we report the design and synthesis of a DNA four-helix bundle. It was found to be extremely rigid and stable. When several such bundles were assembled using appropriate sticky-ends, they formed micrometre-long filaments. However, when creation of two-dimensional sheet-like arrays of the four-helix bundles was attempted, nanoscale rings were observed instead. The exact reason behind the nanoring formation is yet to be ascertained, but it provides an exciting prospect for making programmable circular nanostructures using DNA.


    Directory of Open Access Journals (Sweden)

    K. Hu


    Full Text Available Bundle adjustment with additional parameters is identified as a critical step for precise orthoimage generation and 3D reconstruction of Dunhuang wall paintings. Due to the introduction of self-calibration parameters and quasi-planar constraints, the structure of coefficient matrix of the reduced normal equation is banded-bordered, making the solving process of bundle adjustment complex. In this paper, Conjugate Gradient Bundle Adjustment (CGBA method is deduced by calculus of variations. A preconditioning method based on improved incomplete Cholesky factorization is adopt to reduce the condition number of coefficient matrix, as well as to accelerate the iteration rate of CGBA. Both theoretical analysis and experimental results comparison with conventional method indicate that, the proposed method can effectively conquer the ill-conditioned problem of normal equation and improve the calculation efficiency of bundle adjustment with additional parameters considerably, while maintaining the actual accuracy.

  17. CANFLEX fuel bundle cross-flow endurance test (test report)

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Sung Deok; Chung, C. H.; Chang, S. K.; Kim, B. D.


    As part of the normal refuelling sequence of CANDU nuclear reactor, both new and irradiated bundles can be parked in the cross-flow region of the liner tubes. This situation occurs normally for a few minutes. The fuel bundle which is subjected to the cross-flow should be capable of withstanding the consequences of cross flow for normal periods, and maintain its mechanical integrity. The cross-flow endurance test was conducted for CANFLEX bundle, latest developed nuclear fuel, at CANDU-Hot Test Loop. The test was carried out during 4 hours at the inlet cross-flow region. After the test, the bundle successfully met all acceptance criteria after the 4 hours cross-flow test. (author). 2 refs., 3 tabs.

  18. Introductory lectures on fibre bundles and topology for physicists

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, G.H.


    These lectures may provide useful background material for understanding gauge theories, particularly the nonperturbative effects such as instantons and monopoles. The mathematical language of topology and fibre bundles is introduced.

  19. Bohr--Sommerfeld Lagrangians of moduli spaces of Higgs bundles

    DEFF Research Database (Denmark)

    Biswas, Indranil; Gammelgaard, Niels Leth; Logares, Marina

    Let $X$ be a compact connected Riemann surface of genus at least two. Let $M_H(r,d)$ denote the moduli space of semistable Higgs bundles on $X$ of rank $r$ and degree $d$. We prove that the compact complex Bohr-Sommerfeld Lagrangians of $M_H(r,d)$ are precisely the irreducible components of the n......Let $X$ be a compact connected Riemann surface of genus at least two. Let $M_H(r,d)$ denote the moduli space of semistable Higgs bundles on $X$ of rank $r$ and degree $d$. We prove that the compact complex Bohr-Sommerfeld Lagrangians of $M_H(r,d)$ are precisely the irreducible components...... of the nilpotent cone in $M_H(r,d)$. This generalizes to Higgs $G$-bundles and also to the parabolic Higgs bundles....

  20. Design and synthesis of DNA four-helix bundles

    Energy Technology Data Exchange (ETDEWEB)

    Rangnekar, Abhijit; Gothelf, Kurt V [Department of Chemistry, Centre for DNA Nanotechnology (CDNA) and Interdisciplinary Nanoscience Center (iNANO), Aarhus University, DK-8000 Aarhus C (Denmark); LaBean, Thomas H, E-mail:, E-mail: [Department of Chemistry, Duke University, Durham, NC 27708 (United States)


    The field of DNA nanotechnology has evolved significantly in the past decade. Researchers have succeeded in synthesizing tile-based structures and using them to form periodic lattices in one, two and three dimensions. Origami-based structures have also been used to create nanoscale structures in two and three dimensions. Design and construction of DNA bundles with fixed circumference has added a new dimension to the field. Here we report the design and synthesis of a DNA four-helix bundle. It was found to be extremely rigid and stable. When several such bundles were assembled using appropriate sticky-ends, they formed micrometre-long filaments. However, when creation of two-dimensional sheet-like arrays of the four-helix bundles was attempted, nanoscale rings were observed instead. The exact reason behind the nanoring formation is yet to be ascertained, but it provides an exciting prospect for making programmable circular nanostructures using DNA.

  1. Arthroscopic Stabilization of Chronic Acromioclavicular Joint Dislocations: Triple- Versus Single-Bundle Reconstruction. (United States)

    Tauber, Mark; Valler, Dennis; Lichtenberg, Sven; Magosch, Petra; Moroder, Philipp; Habermeyer, Peter


    Arthroscopically assisted single-bundle (SB) or double-bundle coracoclavicular (CC) ligament reconstruction using autologous tendon grafts has been reported to provide acromioclavicular (AC) joint (ACJ) stability in chronic instability cases. Recently, additional AC ligament reconstruction to provide triple-bundle (TB) stabilization has been introduced but lacks a comparison of clinical and radiological outcomes. Arthroscopically assisted anatomic TB CC and AC reconstruction yields superior clinical and radiological results when compared with nonanatomic SB CC reconstruction. Cohort study; Level of evidence, 2. Twenty-six patients (mean [±SD] age, 46.9 ± 12.8 years) suffering from chronic high-grade ACJ instability underwent ACJ stabilization using autologous hamstring grafts. Twelve patients underwent combined anatomic TB CC and AC reconstruction using a semitendinosus tendon with clavicular interference screw fixation (TB group), and 14 underwent isolated SB CC reconstruction using the AC GraftRope system with a gracilis tendon (SB group). After a minimum follow-up of 2 years (mean, 29.0 ± 7.4 months), patients were evaluated radiologically and clinically using the Constant, American Shoulder and Elbow Surgeons (ASES), Taft, and Acromioclavicular Joint Instability Score (ACJI) outcome measures. The mean Constant score increased significantly in both groups, from 71.6 preoperatively to 88.8 postoperatively in the TB group and from 67.8 to 82.6 in the SB group (P ≤ .009). No intergroup difference was found regarding the final Constant or ASES scores. Regarding the ACJ-specific scores, the final outcomes were significantly different: 10.9 (TB group) versus 9.0 (SB group) for the mean Taft score (P = .018) and 84.7 versus 58.4, respectively, for the mean ACJI score (P = .0001). No significant radiological difference was found regarding the mean CC distance (10.7 mm [TB group] vs 13.1 mm [SB group]). The TB group showed superior horizontal ACJ stability (P = .011

  2. Posterior C1-C2 screw and rod instrument for reduction and fixation of basilar invagination with atlantoaxial dislocation. (United States)

    Guo, Sheng Li; Zhou, Ding Biao; Yu, Xin Guang; Yin, Yi Heng; Qiao, Guang Yu


    To report the surgical technique and preliminary clinical results for the treatment of basilar invagination (BI) with atlantoaxial dislocation (AAD) by posterior C1-C2 pedicle screw and rod instrument. Between July 2012 and August 2013, 33 patients who had BI with AAD underwent surgery at our institution. Pre and postoperative three-dimensional computed tomographic (CT) scans were performed to assess the degree of dislocation. Magnetic resonance (MR) imaging was used to evaluate the compression of the medulla oblongata. For all patients, reduction of the AAD was conducted by two steps: fastening nuts and rods was performed to achieve the horizontal reduction. Distraction between C1 and C2 screws was performed to obtain the vertical reduction. No neurovascular injury occurred during surgery. Follow-up ranged from 6 to 15 months (mean 10.38 months) in 32 patients. Post-operative three-dimensional CT showed that complete horizontal reduction was obtained in 30/33 (90.9%), and complete vertical reduction was obtained in 31/33 (93.9%). The repeated three-dimensional CT and MR image demonstrated that bony fusion and the decompression of the medulla oblongata were obtained in all patients. Clinical symptoms improved significantly 3 months after surgery. This C1-C2 pedicle screw and rod instrument is a promising technique for the treatment of BI with AAD.

  3. A Discrete Theory of Connections on Principal Bundles


    Leok, M; Marsden, JE; Weinstein, AD


    Connections on principal bundles play a fundamental role in expressing the equations of motion for mechanical systems with symmetry in an intrinsic fashion. A discrete theory of connections on principal bundles is constructed by introducing the discrete analogue of the Atiyah sequence, with a connection corresponding to the choice of a splitting of the short exact sequence. Equivalent representations of a discrete connection are considered, and an extension of the pair groupoid composition, t...

  4. On the Geometry of Cotangent Bundles of Lie Groups


    Manga, Bakary


    Lie groups of automorphisms of cotangent bundles of Lie groups are completely characterized and interesting results are obtained. We give prominence to the fact that the Lie groups of automorphisms of cotangent bundles of Lie groups are super symmetric Lie groups. In the cases of orthogonal Lie lgebras, semi-simple Lie algebras and compact Lie algebras we recover by simple methods interesting co-homological known results. The Lie algebra of prederivations encompasses the one of derivations as...

  5. Page 1 Moduli for bundles over curves - 325 through the ...

    Indian Academy of Sciences (India)

    (B End V, with the reduced structure. Note that C is an open subscheme in C and C is a multicone in G) End V. By the hypothesis of the lemma and assumption Mo = G, for te Twe have an isomorphism (p, Eo- ºr, We can interpret p, as a section of the fiber bundle (e. X ..) (G) with fiber G associated to the G × G. bundle Eo * Č, ...

  6. Some Considerations on Horizontal Displacement and Horizontal Displacement Coefficient B

    Directory of Open Access Journals (Sweden)

    Tajduś Krzysztof


    Full Text Available Mining-induced deformations of the ground surface and within the rock mass may pose danger not only for surface constructions but also for underground objects (e.g., tunnels, underground storages, garages, diverse types of pipelines, electric cables, etc. For a proper evaluation of hazard for surface and underground objects, such parameters as horizontal displacement and horizontal deformations, especially their maximum values, are of crucial importance. The paper is an attempt at a critical review of hitherto accomplished studies and state of the art of predicting horizontal displacement u, in particular the coefficient B, whose value allows determination of the value of maximum displacement if the value of maximum slope is known, or the value of maximum deformation if the value of maximum trough slope is recognized. Since the geodesic observations of fully developed subsidence troughs suggest that the value of the coefficient depends on the depth H, radius of main influences range r and properties of overburden rock, in particular the occurrence of sub-eras Paleogene and Neogene layers (old name: Quaternary and Tertiary with low strength parameters, therefore a formula is provided in the present paper allowing for the estimation of the influence of those factors on the value of coefficient B.

  7. Rod strain after pedicle subtraction osteotomy

    DEFF Research Database (Denmark)

    Gehrchen, Poul Martin; Hallager, Dennis Winge; Dahl, Benny


    Pedicle subtraction osteotomy (PSO) can provide major sagittal correction for adult spinal deformity, sometimes achieving correction greater than 308. Surgeons have reported failure rates up to 30% within 2 years, increasing to 46% after 4 to 5 years (SDC Figure 1, Revision following failure is difficult on the patient. PSO has achieved positive outcomes, but when used to correct posture in older patients with spinal deformity and fixed sagittal imbalance, rod breakage often leads to multiple surgical revisions. These complications must be avoided....

  8. Rodded shutdown system for a nuclear reactor (United States)

    Golden, Martin P.; Govi, Aldo R.


    A top mounted nuclear reactor diverse rodded shutdown system utilizing gas fed into a pressure bearing bellows region sealed at the upper extremity to an armature. The armature is attached to a neutron absorber assembly by a series of shafts and connecting means. The armature is held in an uppermost position by an electromagnet assembly or by pressurized gas in a second embodiment. Deenergizing the electromagnet assembly, or venting the pressurized gas, causes the armature to fall by the force of gravity, thereby lowering the attached absorber assembly into the reactor core.

  9. 4-rod RFQ linac for ion implantation

    Energy Technology Data Exchange (ETDEWEB)

    Fujisawa, Hiroshi; Hamamoto, Nariaki; Inouchi, Yutaka [Nisshin Electric Co. Ltd., Kyoto (Japan)


    A 34 MHz 4-rod RFQ linac system has been upgraded in both its rf power efficiency and beam intensity. The linac is able to accelerate in cw operation 0.83 mA of a B{sup +} ion beam from 0.03 to 0.91 MeV with transmission of 61 %. The rf power fed to the RFQ is 29 kW. The unloaded Q-value of the RFQ has been improved approximately 61 % to 5400 by copper-plating stainless steel cooling pipes in the RFQ cavity. (author)

  10. Nonlinear localized elastoplastic waves in a rod (United States)

    Erofeev, V. I.; Leonteva, A. V.; Malkhanov, A. O.


    It has been shown that longitudinal nonlinear stationary elastic-plastic waves can be formed in a rod. Waves can be both periodic and solitary (solitons), which is determined by the index of strain hardening of the material.The velocity of propagation of such waves is less than the speed of the elastic shear wave. Along with classical solitons, so-called “embedded solitons” can be formed, that is, double solitons, one of which with a smaller amplitude and widthis located inside the other with a larger amplitude and width.

  11. Uspon silovatelja: etnicitet, rod i nasilje


    Mežnarić, Silva


    Članak raspravlja o uporabi silovanja kao politike u slučajevima kada se, do tragičnih posljedica, ukrštaju nasilje, rod i etnicitet. Prvo se ispituje kampanja srbijanskih medija 1990. na Kosovu protiv Albanaca kao silovatelja; zatim se analizira upotreba silovanja u prinudnom etničkom čišćenju prilikom srpske agresije na Bosnu, 1992-1993. Pokazuje se da je kampanja na Kosovu bila predigra stvarnom silovanju u Bosni. U oba je slučaja silovanje poslužilo u ograđivanju teritorija i definiranju ...

  12. Solitary waves on nonlinear elastic rods. I

    DEFF Research Database (Denmark)

    Sørensen, Mads Peter; Christiansen, Peter Leth; Lomdahl, P. S.


    Acoustic waves on elastic rods with circular cross section are governed by improved Boussinesq equations when transverse motion and nonlinearity in the elastic medium are taken into account. Solitary wave solutions to these equations have been found. The present paper treats the interaction between...... the solitary waves numerically. It is demonstrated that the waves behave almost like solitons in agreement with the fact that the improved Boussinesq equations are nearly integrable. Thus three conservation theorems can be derived from the equations. A new subsonic quasibreather is found in the case of a cubic...

  13. Mitotic spindle: kinetochore fibers hold on tight to interpolar bundles. (United States)

    Tolić, Iva M


    When a cell starts to divide, it forms a spindle, a micro-machine made of microtubules, which separates the duplicated chromosomes. The attachment of microtubules to chromosomes is mediated by kinetochores, protein complexes on the chromosome. Spindle microtubules can be divided into three major classes: kinetochore microtubules, which form k-fibers ending at the kinetochore; interpolar microtubules, which extend from the opposite sides of the spindle and interact in the middle; and astral microtubules, which extend towards the cell cortex. Recent work in human cells has shown a close relationship between interpolar and kinetochore microtubules, where interpolar bundles are attached laterally to kinetochore fibers almost all along their length, acting as a bridge between sister k-fibers. Most of the interpolar bundles are attached to a pair of sister kinetochore fibers and vice versa. Thus, the spindle is made of modules consisting of a pair of sister kinetochore fibers and a bundle of interpolar microtubules that connects them. These interpolar bundles, termed bridging fibers, balance the forces acting at kinetochores and support the rounded shape of the spindle during metaphase. This review discusses the structure, function, and formation of kinetochore fibers and interpolar bundles, with an emphasis on how they interact. Their connections have an impact on the force balance in the spindle and on chromosome movement during mitosis because the forces in interpolar bundles are transmitted to kinetochore fibers and hence to kinetochores through these connections.

  14. Splitting 3-plane sub-bundles over the product of two real projective spaces

    Directory of Open Access Journals (Sweden)

    Maria Hermínia de Paula Leite Mello


    Full Text Available Let α be a real vector bundle of fiber dimension three over the product RP(m×RP(n which splits as a Whitney sum of line bundles. We show that the necessary and sufficient conditions for α to embed as a sub-bundle of a certain family of vector bundles β of fiber dimension m+n is the vanishing of the last three Stiefel-Whitney classes of the virtual bundle0 β−α. Among the target bundles β we consider the tangent bundle.


    Farrukh, U. O.


    Managing the thermal energy that accumulates within a solid-state laser material under active pumping is of critical importance in the design of laser systems. Earlier models that calculated the temperature distribution in laser rods were single dimensional and assumed laser rods of infinite length. This program presents a new model which solves the temperature distribution problem for finite dimensional laser rods and calculates both the radial and axial components of temperature distribution in these rods. The modeled rod is either side-pumped or end-pumped by a continuous or a single pulse pump beam. (At the present time, the model cannot handle a multiple pulsed pump source.) The optical axis is assumed to be along the axis of the rod. The program also assumes that it is possible to cool different surfaces of the rod at different rates. The user defines the laser rod material characteristics, determines the types of cooling and pumping to be modeled, and selects the time frame desired via the input file. The program contains several self checking schemes to prevent overwriting memory blocks and to provide simple tracing of information in case of trouble. Output for the program consists of 1) an echo of the input file, 2) diffusion properties, radius and length, and time for each data block, 3) the radial increments from the center of the laser rod to the outer edge of the laser rod, and 4) the axial increments from the front of the laser rod to the other end of the rod. This program was written in Microsoft FORTRAN77 and implemented on a Tandon AT with a 287 math coprocessor. The program can also run on a VAX 750 mini-computer. It has a memory requirement of about 147 KB and was developed in 1989.

  16. A quantitative histopathological study of right bundle branch block complicating acute anteroseptal myocardial infarction.


    Okabe, M; Fukuda, K; Nakashima, Y; Hiroki, T; Arakawa, K; Kikuchi, M


    The aim of the present study was to evaluate whether necrosis of the right bundle branch is responsible for development of right bundle branch block in acute myocardial infarction. Twenty patients with acute anteroseptal myocardial infarction were studied--10 with right bundle branch block (group A) and 10 without (group B)--to evaluate by serial sectioning the pathological extent of myocardial infarction surrounding the right bundle branch and also that of right bundle branch necrosis. Myoca...

  17. Grey Rod Test in HANARO Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Choo, K. N.; Kim, B. G.; Kang, Y. H. (and others)


    Westinghouse/KAERI/KNF agreed to perform an irradiation test in the HANARO reactor to obtain irradiation data on the new grey rods that will be part of an AP1000 system. As a preliminary test, two samples containing pure Ag (Reference) and Ag-In-Cd materials provided by Westinghouse Electric Company (WEC) were inserted in a KNF irradiation capsule of 07M-13N. The specimens were irradiated for 95.19days (4 cycles) in the CT test hole of the HANARO of a 30MW thermal output to have a fast neutron fluence of 1.11x10{sup 21}(n/cm{sup 2}) (E>1.0MeV). This report provides all the test conditions and data obtained during the irradiation test of the grey rods in HANARO requested by Westinghouse. The test was prepared according to the meeting minutes (June 26, 2007) and the on-going subject test was stopped midway by the request of Westinghouse.

  18. Steam by-pass reciprocating rod pump

    Energy Technology Data Exchange (ETDEWEB)

    Waterhouse, B. [Weatherford, Edmonton, AB (Canada)


    This article presented the design details of Weatherford's steam by-pass reciprocating rod rod pump which was designed to work under specific well conditions and individual applications, including Imperial Oil's Cold Lake bitumen recovery project located 230 km northeast of Edmonton, Alberta. Imperial Oil uses a cyclic steam stimulation (CSS) process to enhance bitumen recovery from the Clearwater oil sand reservoir. A typical wellbore reach can be up to 700 m and 80 degrees deviation at a target depth of 455 m TVD. These long well bore reaches along with high bottomhole angles and high produced fluid viscosities complicate the design of the artificial lift, which is essentially a modified conventional API pump. The hold-down section is a friction ring design incorporating stainless steel friction rings to provide positive holding force. The steam by-pass coupling is a reduced-diameter tube fitting between the API pump and the friction ring hold-down section. Three stages of the Imperial Cold Lake operation were described, namely the steam injection stage, soak phase stage and production stage. Typically, the steam by-pass pump is suspended in the tubing for the entire cycle. This presentation reviewed the operating steps of the pump, whose average run time in the field is about 15 months, depending on the potential for scaling or sand influx. tab., figs.

  19. Application of polyimide actuator rod seals (United States)

    Watermann, A. W.; Gay, B. F.; Robinson, E. D.; Srinath, S. K.; Nelson, W. G.


    Development of polyimide two-stage hydraulic actuator rod seals for application in high-performance aircraft was accomplished. The significant portion of the effort was concentrated on optimization of the chevron and K-section second-stage seal geometries to satisfy the requirements for operation at 450 K (350 F) with dynamic pressure loads varying between 200 psig steady-state and 1500 psig impulse cycling. Particular significance was placed on reducing seal gland dimension by efficiently utilizing the fatigue allowables of polyimide materials. Other objectives included investigation of pressure balancing techniques for first-stage polyimide rod seals for 4000 psig 450 K(350 F) environment and fabrication of a modular retainer for the two-stage combination. Seals were fabricated in 0.0254 m (1.0in.) and 0.0635 m (2.5in.) sizes and tested for structural integrity, frictional resistance, and endurance life. Test results showed that carefully designed second stages using polyimides could be made to satisfy the dynamic return pressure requirements of applications in high-performance aircraft. High wear under full system pressure indicated that further research is necessary to obtain an acceptable first-stage design. The modular retainer was successfully tested and showed potential for new actuator applications.

  20. On the Wave Stresses in the Rods of Anvil Hammers

    Directory of Open Access Journals (Sweden)

    V. M. Sinitskiy


    Full Text Available With operating anvil hammers, there are rigid impacts of die tools, and as a result, almost instantaneous impact stops of the falling parts of hammer. Such operating conditions lead to the accelerated breakdowns of rods because of significant wave stresses arising in them. Common differential and integral methods to estimate wave stresses are widespread in engineering practice. However, to use them a researcher has to possess certain skills and special software. We consider the method for estimating the wave stresses in the rods of anvil hammers based on Laplace transforms (LT of wave equation. The article shows a procedure to set up and solve differential wave equations by operator method. These equations describe the wave propagation process of strains and stresses in the rods of anvil hammers with rigid impact and taking into account a damping rod connection with the head of hammer. The method takes into consideration an influence of both piston and rod weights and of mechanical and geometrical characteristics of rod on the stress value in the placement of rod in hammer head. Results analysis shows that a sufficiently efficient method for practical improving the durability of rods is the method of damping impact load on the rod through setting the damping devices in the form either of elastic "pad" of one or another design or of hydraulic shock absorbers in the placement of its connection with the hammer head. In this case there is a change of the wave front, it becomes flatter. It is shown that the stresses in the rod are proportional to the amount of wave stresses because of the own impact of rod and piston, which make a total weight of the system. Effect of piston weight on the stresses value at the rod during impact is directly proportional to the ratio of its weight to the rod weight. The geometric parameters of rod and the speed of the falling parts before the impact also influence on the value of stresses in the rod.The represented

  1. Vortex patterns in a superconducting-ferromagnetic rod

    Energy Technology Data Exchange (ETDEWEB)

    Romaguera, Antonio R. de C, E-mail: antonio.romaguera@df.ufrpe.b [Departamento de Fi' sica, Universidade Federal Rural de Pernambuco, 52171-900 Recife, Pernambuco (Brazil); Doria, Mauro M. [Departamento de Fi' sica dos Solidos, Universidade Federal do Rio de Janeiro, 21941-972 Rio de Janeiro (Brazil); Peeters, Francois M. [Departement Fysica, Universiteit Antwerpen, Groenenborgerlaan 171, B-2020 Antwerpen (Belgium)


    A superconducting rod with a magnetic moment on top develops vortices obtained here through 3D calculations of the Ginzburg-Landau theory. The inhomogeneity of the applied field brings new properties to the vortex patterns that vary according to the rod thickness. We find that for thin rods (disks) the vortex patterns are similar to those obtained in presence of a homogeneous magnetic field instead because they consist of giant vortex states. For thick rods novel patterns are obtained as vortices are curve lines in space that exit through the lateral surface.

  2. TileCal ROD Hardware and Software Requirements

    CERN Document Server

    Castelo, J; Cuenca, C; Ferrer, A; Fullana, E; Higón, E; Iglesias, C; Munar, A; Poveda, J; Ruiz-Martínez, A; Salvachúa, B; Solans, C; Valls, J A


    In this paper we present the specific hardware and firmware requirements and modifications to operate the Liquid Argon Calorimeter (LiArg) ROD motherboard in the Hadronic Tile Calorimeter (TileCal) environment. Although the use of the board is similar for both calorimeters there are still some differences in the operation of the front-end associated to both detectors which make the use of the same board incompatible. We review the evolution of the design of the ROD from the early prototype stages (ROD based on commercial and Demonstrator boards) to the production phases (ROD final board based on the LiArg design), with emphasis on the different operation modes for the TileCal detector. We start with a short review of the TileCal ROD system functionality and then we detail the different ROD hardware requirements for options, the baseline (ROD Demo board) and the final (ROD final high density board). We also summarize the performance parameters of the ROD motherboard based on the final high density option and s...

  3. The R&D PERFROI Project on Thermal Mechanical and Thermal Hydraulics Behaviors of a Fuel Rod Assembly during a Loss of Coolant Accident

    Energy Technology Data Exchange (ETDEWEB)

    Repetto, G. [Institut de Radioprotection et de Surete Nucleaire, Cadarache (France); Dominguez, C. [Institut de Radioprotection et de Surete Nucleaire, Cadarache (France); Durville, B. [Institut de Radioprotection et de Surete Nucleaire, Cadarache (France); Carnemolla, S. [Institut de Radioprotection et de Surete Nucleaire, Cadarache (France); Campello, D. [Institut National des Sciences Appliques, Lyon (France); Tardiff, N. [Institut National des Sciences Appliques, Lyon (France); Gradeck, M. [Univ. de Lorraine, Nancy, France. LEMTA


    The safety principle in case of a LOCA is to preserve the short and long term coolability of the core. The associated safety requirements are to ensure the resistance of the fuel rods upon quench and post-quench loads and to maintain a coolable geometry in the core. An R&D program has been launched by IRSN with the support of EDF, to perform both experimental and modeling activities in the frame of the LOCA transient, on technical issues such as: - flow blockage within a fuel rods bundle and its potential impact on coolability, - fuel fragment relocation in the ballooned areas: its potential impact on cladding PCT (Peak Cladding Temperature) and on the maximum oxidation rate, - potential loss of cladding integrity upon quench and post-quench loads. The PERFROI project (2014-2019) focusing on the first above issue, is structured in two axes: 1. axis 1: thermal mechanical behavior of deformation and rupture of cladding taking into account the contact between fuel rods; specific research at LaMCoS laboratory focus on the hydrogen behavior in cladding alloys and its impact on the mechanical behavior of the rod; and, 2. axis 2: thermal hydraulics study of a partially blocked region of the core (ballooned area taking into account the fuel relocation with local over power), during cooling phase by water injection; More detailed activities foreseen in collaboration with LEMTA laboratory will focus on the characterization of two phase flows with heat transfer in deformed structures.

  4. Histones bundle F-actin filaments and affect actin structure. (United States)

    Blotnick, Edna; Sol, Asaf; Muhlrad, Andras


    Histones are small polycationic proteins complexed with DNA located in the cell nucleus. Upon apoptosis they are secreted from the cells and react with extracellular polyanionic compounds. Actin which is a polyanionic protein, is also secreted from necrotic cells and interacts with histones. We showed that both histone mixture (histone type III) and the recombinant H2A histone bundles F-actin, increases the viscosity of the F-actin containing solution and polymerizes G-actin. The histone-actin bundles are relatively insensitive to increase of ionic strength, unlike other polycation, histatin, lysozyme, spermine and LL-37 induced F-actin bundles. The histone-actin bundles dissociate completely only in the presence of 300-400 mM NaCl. DNA, which competes with F-actin for histones, disassembles histone induced actin bundles. DNase1, which depolymerizes F- to G-actin, actively unbundles the H2A histone induced but slightly affects the histone mixture induced actin bundles. Cofilin decreases the amount of F-actin sedimented by low speed centrifugation, increases light scattering and viscosity of F-actin-histone mixture containing solutions and forms star like superstructures by copolymerizing G-actin with H2A histone. The results indicate that histones are tightly attached to F-actin by strong electrostatic and hydrophobic forces. Since both histones and F-actin are present in the sputum of patients with cystic fibrosis, therefore, the formation of the stable histone-actin bundles can contribute to the pathology of this disease by increasing the viscosity of the sputum. The actin-histone interaction in the nucleus might affect gene expression.

  5. Histones bundle F-actin filaments and affect actin structure.

    Directory of Open Access Journals (Sweden)

    Edna Blotnick

    Full Text Available Histones are small polycationic proteins complexed with DNA located in the cell nucleus. Upon apoptosis they are secreted from the cells and react with extracellular polyanionic compounds. Actin which is a polyanionic protein, is also secreted from necrotic cells and interacts with histones. We showed that both histone mixture (histone type III and the recombinant H2A histone bundles F-actin, increases the viscosity of the F-actin containing solution and polymerizes G-actin. The histone-actin bundles are relatively insensitive to increase of ionic strength, unlike other polycation, histatin, lysozyme, spermine and LL-37 induced F-actin bundles. The histone-actin bundles dissociate completely only in the presence of 300-400 mM NaCl. DNA, which competes with F-actin for histones, disassembles histone induced actin bundles. DNase1, which depolymerizes F- to G-actin, actively unbundles the H2A histone induced but slightly affects the histone mixture induced actin bundles. Cofilin decreases the amount of F-actin sedimented by low speed centrifugation, increases light scattering and viscosity of F-actin-histone mixture containing solutions and forms star like superstructures by copolymerizing G-actin with H2A histone. The results indicate that histones are tightly attached to F-actin by strong electrostatic and hydrophobic forces. Since both histones and F-actin are present in the sputum of patients with cystic fibrosis, therefore, the formation of the stable histone-actin bundles can contribute to the pathology of this disease by increasing the viscosity of the sputum. The actin-histone interaction in the nucleus might affect gene expression.

  6. Heterologous expression of hydrophobins RodA and RodB from Aspergillus fumigatus in host Pichia pastoris

    DEFF Research Database (Denmark)

    Pedersen, Mona Højgaard; Borodina, Irina; Frisvad, Jens Christian

    proteins with the signal sequence of alfa-mating factor from Saccharomyces cerevisia known to work well for protein secretion from P. pastoris and the pPICZB plasmids had proteins cloned with their native signal sequences. The plasmids were linearized, transformed into P. pastoris strain X33...... and transformants were selected by zeocin resistance. The presence of the RodA and RodB genes in the transformants was confirmed by colony PCR. The expression of RodA and RodB genes was induced by growing cells in culture flasks for three days in buffered complex methanol medium as protein production was dependent...

  7. CFD analysis of turbulent flow in nuclear fuel bundle with flow mixing device

    Energy Technology Data Exchange (ETDEWEB)

    In, Wang Kee; Oh, Dong Seok; Chun, Tae Hyun [Korea Atomic Energy Research Institute, Taejon (Korea)


    A CFD analysis was performed to confirm the applicability of the CFD method and to examine the 3-D turbulent flow characteristics in rod bundles with typical flow mixing promoters on grid spacer. Both the axial and lateral mean velocities predicted by the CFD method showed good agreement with the measurements except for the axial velocity near the spacer with the split vane. The CFD predictions produced the swirling flow pattern in the subchannel for the split-vane design and the crossflow mixing between adjacent subchannels for the ripped-open blades. The actual flow rate through the Y-nozzle is predicted to be smaller than the expected flow rate that is estimated based on the ratio of flow area of the Y-nozzle to the total flow area of the subchannel. The pressure drop across the Y-nozzle spacer is also estimated to be larger than the other spacer designs. The CFD simulations of the swirl-vane design showed an intense swirling flow in the subchannel but a negligible crossflow between neighboring subchannels. (author). 9 refs., 45 figs., 2 tabs.

  8. Effects of different initial bundle tensioning strategies on the outcome of double-bundle ACL reconstruction: a cohort study

    Directory of Open Access Journals (Sweden)

    Muneta Takeshi


    Full Text Available Abstract Background This study was performed to investigate the effects of different strategies and initial tension applied to each one of the bundles, antero-medial (AM and postero-lateral (PL, on clinical outcome in double bundle (DB ACL reconstruction. Methods One hundred fifty-one primary unilateral DB ACL reconstructions performed by a single surgeon from 1994 through 2002 were included in the study with a follow-up of at least 24 months. They were divided in the following 3 groups: Group I - Higher initial tension applied manually in the AM bundle compared to PL. II - Higher tension applied in the PL bundle compared to AM. III - The 2 bundles were attempted to be equally tensioned. All fixations were performed in 30 degrees of flexion. Group I = 59 patients, group II = 53 patients and group III = 39 patients. The groups had no statistical differences concerning demographic distribution. Clinical outcome was retrospectively evaluated by use of knee range of motion, manual knee laxity tests, KT-1000, Lysholm knee scale, subjective recovery scale and sports performance recovery scale. The differences of data were analyzed among the three groups. Results Group I showed a significant extension deficit compared with groups II and III. ANOVA revealed a significant difference of anterior laxity measured by the KT-1000 (average KT difference of 2.1, 2.1 and 1.2 mm in Group I, II and III, respectively. A statistical difference was found among the three groups regarding subjective and sports performance recovery scales with Group II showing higher scores in recovery than Group I. Conclusions The current clinical study does not recommend manual maximum of initial tension applied to the anteromedial or posterolateral bundles with graft tension imbalance at 30 degrees of flexion in double-bundle ACL reconstruction to achieve a better clinical outcome.

  9. The 2-Hilbert space of a prequantum bundle gerbe (United States)

    Bunk, Severin; Sämann, Christian; Szabo, Richard J.

    We construct a prequantum 2-Hilbert space for any line bundle gerbe whose Dixmier-Douady class is torsion. Analogously to usual prequantization, this 2-Hilbert space has the category of sections of the line bundle gerbe as its underlying 2-vector space. These sections are obtained as certain morphism categories in Waldorf’s version of the 2-category of line bundle gerbes. We show that these morphism categories carry a monoidal structure under which they are semisimple and abelian. We introduce a dual functor on the sections, which yields a closed structure on the morphisms between bundle gerbes and turns the category of sections into a 2-Hilbert space. We discuss how these 2-Hilbert spaces fit various expectations from higher prequantization. We then extend the transgression functor to the full 2-category of bundle gerbes and demonstrate its compatibility with the additional structures introduced. We discuss various aspects of Kostant-Souriau prequantization in this setting, including its dimensional reduction to ordinary prequantization.

  10. Improvements to Wire Bundle Thermal Modeling for Ampacity Determination (United States)

    Rickman, Steve L.; Iannello, Christopher J.; Shariff, Khadijah


    Determining current carrying capacity (ampacity) of wire bundles in aerospace vehicles is critical not only to safety but also to efficient design. Published standards provide guidance on determining wire bundle ampacity but offer little flexibility for configurations where wire bundles of mixed gauges and currents are employed with varying external insulation jacket surface properties. Thermal modeling has been employed in an attempt to develop techniques to assist in ampacity determination for these complex configurations. Previous developments allowed analysis of wire bundle configurations but was constrained to configurations comprised of less than 50 elements. Additionally, for vacuum analyses, configurations with very low emittance external jackets suffered from numerical instability in the solution. A new thermal modeler is presented allowing for larger configurations and is not constrained for low bundle infrared emissivity calculations. Formulation of key internal radiation and interface conductance parameters is discussed including the effects of temperature and air pressure on wire to wire thermal conductance. Test cases comparing model-predicted ampacity and that calculated from standards documents are presented.

  11. Anatomy of an Oligourea Six-Helix Bundle. (United States)

    Lombardo, Caterina M; Collie, Gavin W; Pulka-Ziach, Karolina; Rosu, Frederic; Gabelica, Valerie; Mackereth, Cameron D; Guichard, Gilles


    Non-natural synthetic oligomers that adopt well-defined secondary structures (i.e., foldamers) represent appealing components for the fabrication of bioinspired self-assembled architectures at the nanometer scale. Recently, peptidomimetic N,N'-linked oligourea helices have been designed de novo with the ability to fold into discrete helix bundles in aqueous conditions. In order to gain better insight into the determinants of oligourea helix bundle formation, we have investigated the sequence-to-structure relationship of an 11-mer oligourea previously shown to assemble into a six-helix bundle. Using circular dichroism, NMR spectroscopy, native mass-spectrometry and X-ray crystallography, we studied how bundle formation was affected by systematic replacement of the hydrophobic surface of the oligourea helix with either polar or different hydrophobic side chains. The molecular information gathered here has revealed several key requirements for foldamer bundle formation in aqueous conditions, and provides valuable insight toward the development of foldamer quaternary assemblies with improved (bio)physical properties and divergent topologies.

  12. Ecosystem service bundles for analyzing tradeoffs in diverse landscapes (United States)

    Raudsepp-Hearne, C.; Peterson, G. D.; Bennett, E. M.


    A key challenge of ecosystem management is determining how to manage multiple ecosystem services across landscapes. Enhancing important provisioning ecosystem services, such as food and timber, often leads to tradeoffs between regulating and cultural ecosystem services, such as nutrient cycling, flood protection, and tourism. We developed a framework for analyzing the provision of multiple ecosystem services across landscapes and present an empirical demonstration of ecosystem service bundles, sets of services that appear together repeatedly. Ecosystem service bundles were identified by analyzing the spatial patterns of 12 ecosystem services in a mixed-use landscape consisting of 137 municipalities in Quebec, Canada. We identified six types of ecosystem service bundles and were able to link these bundles to areas on the landscape characterized by distinct social–ecological dynamics. Our results show landscape-scale tradeoffs between provisioning and almost all regulating and cultural ecosystem services, and they show that a greater diversity of ecosystem services is positively correlated with the provision of regulating ecosystem services. Ecosystem service-bundle analysis can identify areas on a landscape where ecosystem management has produced exceptionally desirable or undesirable sets of ecosystem services. PMID:20194739

  13. Syntheses of Nanostructure Bundles Based on Semiconducting Metal Silicides (United States)

    Li, Wen; Ishikawa, Daisuke; Tatsuoka, Hirokazu


    A variety of nanostructure bundles and arrays based on semiconducting metal silicides have been synthesized using abundant and non-toxic starting materials. Three types of fabrication techniques of the nanostructure bundles or arrays, including direct growth, template synthesis using natural nanostructured materials and template synthesis using artificially fabricated nanostructured materials are demonstrated. CrSi2 nanowire bundles were directly grown by the exposure of Si substrates to CrCl2 vapor at atmospheric pressure. A hexagonal MoSi2 nanosheet, Mg2Si/MgO composite nanowire and Mg2Si nanowire bundles and MnSi1.7 nanowire array were synthesized using a MoS2 layered material, a SiOx nanofiber bundle, a Si nanowire array, and a Si nanowire array as the templates, respectively. Additionally, the fabrication phenomenon and structural properties of the nanostructured semiconducting metal silicides were investigated. These reactions provided the low-cost and controllable synthetic techniques to synthesize large scale and one-dimensional semiconducting metal silicides for thermoelectric applications.

  14. Nuclear reactor shutdown control rod assembly (United States)

    Bilibin, Konstantin


    A temperature responsive, self-actuated nuclear reactor shutdown control rod assembly 10. The upper end 18 of a lower drive line 17 fits within the lower end of an upper drive line 12. The lower end (not shown) of the lower drive line 17 is connected to a neutron absorber. During normal temperature conditions the lower drive line 17 is supported by detent means 22,26. When an overtemperature condition occurs thermal actuation means 34 urges ring 26 upwardly sufficiently to allow balls 22 to move radially outwardly thereby allowing lower drive line 17 to move downwardly toward the core of the nuclear reactor resulting in automatic reduction of the reactor powder.

  15. A prospective comparative study of clinical and functional outcomes between anatomic double bundle and single bundle hamstring grafts for arthroscopic anterior cruciate ligament reconstruction. (United States)

    Morey, Vivek M; Nag, Hira Lal; Chowdhury, Buddhadev; Sankineani, Sukesh Rao; Naranje, Sameer M


    Despite a number of studies comparing postoperative stability and function after anatomic single bundle and double bundle anterior cruciate ligament reconstruction, it remains unclear whether double bundle reconstruction has better functional outcome than single bundle anterior cruciate ligament reconstruction. To compare the subjective functional outcome as well as clinical stability in patients treated with either anatomic single bundle or anatomic double bundle anterior cruciate ligament (ACL) reconstruction. We hypothesized that there would be no difference in the postoperative functional outcome and clinical stability between anatomical double bundle anterior cruciate ligament reconstructions when compared to single bundle anterior cruciate ligament reconstructions. We prospectively followed 40 patients out of which, 20 patients were operated for anatomic single bundle ACL reconstruction and other 20 patients underwent anatomic double bundle ACL reconstruction. Patient evaluation using the laxity tests and outcome scales was done preoperatively and at 12, 24 and 48 months after the surgery. Clinical stability was assessed by Lachman test, Pivot shift test and Delhi active test. Functional outcome was assessed by International Knee Documentation Committee (IKDC), Lysholm and Modified Cincinnati scores. Patients in both groups were evaluated at regular intervals for a minimum period of 48 months (mean 51 months, range 48-56 months). For all subjective scores, double bundle group patients reported statistically significant higher scores compared to single bundle group patients. Graded stability results of the Lachman, and Pivot shift tests were significantly higher in the anatomically reconstructed double bundle patient group. We suggest that functional outcome and clinical stability may be better with anatomical double bundle anterior cruciate ligament reconstruction as compared to anatomical single bundle anterior cruciate ligament reconstruction. Copyright

  16. Panspermia and horizontal gene transfer (United States)

    Klyce, Brig


    Evidence that extremophiles are hardy and ubiquitous is helping to make panspermia a respectable theory. But even if life on Earth originally came from space, biologists assume that the subsequent evolution of life is still governed by the darwinian paradigm. In this review we show how panspermia could amend darwinism and point to a cosmic source for, not only extremophiles but, all of life. This version of panspermia can be called "strong panspermia." To support this theory we will discuss recent evidence pertaining to horizontal gene transfer, viruses, genes apparently older than the Earthly evolution of the features they encode, and primate-specific genes without identifiable precursors.

  17. Optimized Control Rods of the BR2 Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kalcheva, Silva; Koonen, E.


    At the present time the BR-2 reactor uses control elements with cadmium as neutron absorbing part. The lower section of the control element is a beryllium assembly cooled by light water. Due to the burn up of the lower end of the cadmium section during the reactor operation, the presently used rods for reactivity control of the BR-2 reactor have to be replaced by new ones. Considered are various types Control Rods with full active part of the following materials: cadmium (Cd), hafnium (Hf), europium oxide (Eu2O3) and gadolinium (Gd2O3). Options to decrease the burn up of the control rod material in the hot spot, such as use of stainless steel in the lower active part of the Control Rod are discussed. Comparison with the characteristics of the presently used Control Rods types is performed. The changing of the characteristics of different types Control Rods and the perturbation effects on the reactor neutronics during the BR-2 fuel cycle are investigated. The burn up of the Control Rod absorbing material, total and differential control rods worth, macroscopic and effective microscopic absorption cross sections, fuel and reactivity evolution are evaluated during approximately 30 operating cycles.

  18. Tunable attractions directing nonequilibrium states in dispersions of hard rods

    NARCIS (Netherlands)

    Bruggen, M.P.B. van; Lekkerkerker, H.N.W.


    The effect of attractive interactions on the phase behavior of colloidal hard rods has been studied by the addition of nonadsorbing polymer. In these rod-polymer mixtures, four pathways of phase separation can be distinguished: nucleation and growth, spinodal decomposition, aggregation, and

  19. Switch isotropic/anisotropic wettability via dual-scale rods

    Directory of Open Access Journals (Sweden)

    Yang He


    Full Text Available It is the first time to demonstrate the comparison of isotropic/anisotropic wettability between dual-scale micro-nano-rods and single-scale micro-rods. Inspired by the natural structures of rice leaf, a series of micro-nano-rods and micro-rods with different geometric parameters were fabricated using micro-fabrication technology. Experimental measured apparent contact angles and advancing and receding contact angles from orthogonal orientations were characterized. The difference of contact angles from orthogonal orientation on dual-scale rods was much smaller than those on single-scale rods in both static and dynamic situation. It indicated that the dual-scale micro-nano-rods showed isotropic wettability, while single-scale micro-rods showed anisotropic wettability. The switch of isotropic/anisotropic wettability could be illustrated by different wetting state and contact line moving. It offers a facial way to switch isotropic/anisotropic wettability of the surface via dual-scale or single-scale structure.

  20. Numerical investigation of flow past a row of rectangular rods

    Directory of Open Access Journals (Sweden)

    S.Ul. Islam


    Full Text Available A numerical study of uniform flow past a row of rectangular rods with aspect ratio defined as R = width/height = 0.5 is performed using the Lattice Boltzmann method. For this study the Reynolds number (Re is fixed at 150, while spacings between the rods (g are taken in the range from 1 to 6. Depending on g, the flow is classified into four patterns: flip-flopping, nearly unsteady-inphase, modulated inphase-antiphase non-synchronized and synchronized. Sudden jumps in physical parameters were observed, attaining either maximum or minimum values, with the change in flow patterns. The mean drag coefficient (Cdmean of middle rod is higher than the second and fourth rod for flip-flopping pattern while in case of nearly unsteady-inphase the middle rod attains minimum drag coefficient. It is also found that the Strouhal number (St of first, second and fifth rod decreases as g increases while that of other two have mixed trend. The results further show that there exist secondary interaction frequencies together with primary vortex shedding frequency due to jet in the gap between rods for 1 ⩽ g ⩽ 3. For the average values of Cdmean and St, an empirical relation is also given as a function of gap spacing. This relation shows that the average values of Cdmean and St approach to those of single rectangular rod with increment in g.

  1. Probabilistic thermo-chemical analysis of a pultruded composite rod

    NARCIS (Netherlands)

    Baran, Ismet; Tutum, Cem C.; Hattel, Jesper H.


    In the present study the deterministic thermo-chemical pultrusion simulation of a composite rod taken from the literature [7] is used as a validation case. The predicted centerline temperature and cure degree profiles of the rod match well with those in the literature [7]. Following the validation

  2. Rapid calibaration of the control rod of miniature neutron source ...

    African Journals Online (AJOL)

    An innovative method of combining the well-known computer codes WIMS and CITATION in an interactive Windows environment to calculate the control rod worth and generate the calibration data/curve of single-contr-ol rod miniature source reactor (MNSR) types has been developed and tested. In the scheme, once ...

  3. Ultrasonic detection of cracks in uniaxial glass fibre rods

    CSIR Research Space (South Africa)

    Loveday, PW


    Full Text Available propagation in the rods. The authors attempt to model the excitation and transmission of waves along undamaged as well as damaged rods in order to predict the received signals, and we compare the model results with experimental data. Specially developed...

  4. 49 CFR 236.794 - Rod, up-and-down. (United States)


    ... 49 Transportation 4 2010-10-01 2010-10-01 false Rod, up-and-down. 236.794 Section 236.794 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., up-and-down. A rod used for connecting the semaphore arm to the operating mechanism of a signal. ...

  5. Damage development in rod-on-rod impact test on 1100 pure aluminum (United States)

    Iannitti, G.; Bonora, N.; Bourne, N.; Ruggiero, A.; Testa, G.


    Stress triaxiality plays a major role in the nucleation and growth of ductile damage in metals and alloys. Although, the mechanisms responsible for ductile failure are the same at low and high strain rate, in impact dynamics, in addition to time resolved stress triaxiality and plastic strain accumulation, pressure also contributes to establish the condition for ductile failure to occur. In this work, ductile damage development in 1100 commercially pure aluminum was investigated by means of rod-on-rod (ROR) impact tests. Based on numerical simulations, using a continuum damage mechanics (CDM) model that accounts for the role of pressure on damage parameters and stochastic variability of such parameters, the impact velocity for no damage, incipient and fully developed damage were estimated. ROR tests at selected velocities were performed and damage distribution and extent were investigated by sectioning of soft recovered samples. Comparison between numerical simulations and experimental results is presented and discussed.

  6. Interfacial colloidal rod dynamics: Coefficients, simulations, and analysis (United States)

    Yang, Yuguang; Bevan, Michael A.


    Colloidal rod diffusion near a wall is modeled and simulated based on a constrained Stokesian dynamic model of chains-of-spheres. By modeling colloidal rods as chains-of-spheres, complete diffusion tensors are computed for colloidal rods in bulk media and near interfaces, including hydrodynamic interactions, translation-rotation coupling, and all diffusion modes in the particle and lab frames. Simulated trajectories based on the chain-of-spheres diffusion tensor are quantified in terms of typical experimental quantities such as mean squared positional and angular displacements as well as autocorrelation functions. Theoretical expressions are reported to predict measured average diffusivities as well as the crossover from short-time anisotropic translational diffusion along the rod's major axis to isotropic diffusion. Diffusion modes are quantified in terms of closed form empirical fits to model results to aid their use in interpretation and prediction of experiments involving colloidal rod diffusion in interfacial and confined systems.

  7. RODMOD: a code for control rod positioning. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Vondy, D.R.; Fowler, T.B.


    The report documents a computer code which has been implemented to position control rods according to a prescribed schedule during the calculation of a reactor history. Control rods may be represented explicitly with or without internal black absorber conditions in selected energy groups, or fractional insertion may be done, or both, in a problem. There is provision for control rod follower, movement of materials through a series of zones in a closed loop, and shutdown rod insertion and subsequent removal to allow the reactor history calculation to be continued. This code is incorporated in the system containing the VENTURE diffusion theory neutronics and the BURNER exposure codes for routine use. The implemented automated procedures cause the prescribed control rod insertion schedule to be applied without the access of additional user input data during the calculation of a reactor operating history.

  8. Study of the anti-sand sucker rod pump (United States)

    Wei, Hangxin; Lv, Bingxin; Xi, Wenkui; Yi, Peng


    In order to solve the problem of sand stuck in the sucker rod pump, an anti-sand sucker rod pump is designed. The anti-sand sucker rod pump includes the conventional sucker rod pump and the swirl flow device. The sand particles can be separated from the oil in the swirl flow device, so the plunger of the sucker rod pump cannot be stuck. The motion equation of the sand particles in oil is deduced. The virtual model of the swirl flow device is built in GAMBIT software. And simulation of solid-liquid two phase flow is simulated in software FLUENT. The simulation results show that the swirl flow device can realize the sand particles separation from the oil completely. So the pump can have the effect of anti-sands.

  9. Buckling of a thin rod under cylindrical constraint (United States)

    Miller, Jay; Su, Tianxiang; Wicks, Nathan; Pabon, Jahir; Bertoldi, Katia; Reis, Pedro


    We investigate the buckling and post-buckling behavior of a thin elastic rod, under cylindrical constraint, with distributed loading. Our precision model experiments consist of injecting a custom-fabricated rod into a transparent glass pipe. Under imposed velocity (leading to frictional axial loading), a portion of the initially straight rod first buckles into a sinusoidal mode and eventually undergoes a secondary instability into a helical configuration. The buckling and post-buckling behavior is found to be highly dependent on the system's geometry, namely the injected rod length and the aspect ratio of the rod to pipe diameter, as well as material parameters. We quantify the critical loads for this sequence of instabilities, contrast our results with numerical experiments and rationalize the observed behavior through scaling arguments.

  10. Semiconductor Quantum Rods as Single Molecule FluorescentBiological Labels

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Aihua; Gu, Weiwei; Boussert, Benjamine; Koski, Kristie; Gerion, Daniele; Manna, Liberato; Le Gros, Mark; Larabell, Carolyn; Alivisatos, A. Paul


    In recent years, semiconductor quantum dots have beenapplied with great advantage in a wide range of biological imagingapplications. The continuing developments in the synthesis of nanoscalematerials and specifically in the area of colloidal semiconductornanocrystals have created an opportunity to generate a next generation ofbiological labels with complementary or in some cases enhanced propertiescompared to colloidal quantum dots. In this paper, we report thedevelopment of rod shaped semiconductor nanocrystals (quantum rods) asnew fluorescent biological labels. We have engineered biocompatiblequantum rods by surface silanization and have applied them fornon-specific cell tracking as well as specific cellular targeting. Theproperties of quantum rods as demonstrated here are enhanced sensitivityand greater resistance for degradation as compared to quantum dots.Quantum rods have many potential applications as biological labels insituations where their properties offer advantages over quantumdots.

  11. Symposium on Singularities, Representation of Algebras, and Vector Bundles

    CERN Document Server

    Trautmann, Günther


    It is well known that there are close relations between classes of singularities and representation theory via the McKay correspondence and between representation theory and vector bundles on projective spaces via the Bernstein-Gelfand-Gelfand construction. These relations however cannot be considered to be either completely understood or fully exploited. These proceedings document recent developments in the area. The questions and methods of representation theory have applications to singularities and to vector bundles. Representation theory itself, which had primarily developed its methods for Artinian algebras, starts to investigate algebras of higher dimension partly because of these applications. Future research in representation theory may be spurred by the classification of singularities and the highly developed theory of moduli for vector bundles. The volume contains 3 survey articles on the 3 main topics mentioned, stressing their interrelationships, as well as original research papers.

  12. Narrow muon bundles from muon pair production in rock

    CERN Document Server

    Kudryavtsev, V A; Spooner, N J C


    We revise the process of muon pair production by high-energy muons in rock using the recently published cross-section. The three- dimensional Monte Carlo code MUSIC has been used to obtain the characteristics of the muon bundles initiated via this process. We have compared them with those of conventional muon bundles initiated in the atmosphere and shown that large underground detectors, capable of collecting hundreds of thousands of multiple muon events, can discriminate statistically muon induced bundles from conventional ones. However, we find that the enhancement of the measured muon decoherence function over that predicted at small distances, recently reported by the MACRO experiment, cannot be explained by the effect of muon pair production alone, unless its cross-section is underestimated by a factor of 3. (20 refs).

  13. Product bundling as a customer loyalty strategy; Kundenbindung durch Produktbuendel

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, H.G. [Arthur Andersen Business Consulting GmbH, Duesseldorf (Germany)


    In the deregulated market in electricity, all marketers and energy-related service providers are competing not only for new customers, but also for customer loyalty. The article sets out concepts and strategies developed by a business consulting firm, for maintaing or enhancing customer loyalty in the end-use market segment, focusing on customized product bundling. A four-tier approach for product bundle development and implementation is discussed. (orig./CB) [German] Fuer Energieversorger und -dienstleister ergibt sich neben der Neukundengewinnung der strategische Zwang zur Bindung bestehender Kunden. An praktischen Ansaetzen fuer Privatkunden stehen neben Value-Added-Services und Incentives (Kundenclub, -karte) nicht zuletzt Produktbuendel (Bundles) zur Verfuegung. Zur erfolgreichen Entwicklung und Implementierung von Produktbuendeln wird ein vierphasiges Vorgehensmodell erlaeutert. (orig./CB)

  14. Transient Left Bundle Branch Block due to Severe Hyperkalemia. (United States)

    Kumar, Kishore; Biyyam, Madhavi; Singh, Amandeep; Bajantri, Bharat; Tariq, Hassan; Nayudu, Suresh Kumar; Chilimuri, Sridhar


    Hyperkalemia is a potentially life-threatening electrolyte imbalance that can lead to sudden death from cardiac arrhythmias and asystole. We present a case of transient left bundle branch block pattern on an electrocardiogram (ECG) secondary to hyperkalemia in a patient with history of end-stage renal disease. A 52-year-old man presented to the emergency room (ER) with chief complaints of weakness and lethargy after missing his regularly scheduled session of hemodialysis. A 12-lead ECG in the ER showed sinus tachycardia at 118 beats/min, wide QRS complexes, peaked T waves and left bundle branch block-like pattern. The initial basic metabolic panel revealed a serum potassium level of 8.8 mEq/L. Subsequently, the patient underwent emergent hemodialysis. Serum chemistry after hemodialysis showed improvement in serum potassium to 4.3 mEq/L. Repeat ECG performed after correcting potassium showed dissolution of left bundle branch block finding.

  15. Gradient Bundle Analysis: A Full Topological Approach to Chemical Bonding

    CERN Document Server

    Morgenstern, Amanda


    The "chemical bond" is a central concept in molecular sciences, but there is no consensus as to what a bond actually is. Therefore, a variety of bonding models have been developed, each defining the structure of molecules in a different manner with the goal of explaining and predicting chemical properties. This thesis describes the initial development of gradient bundle analysis (GBA), a chemical bonding model that creates a high resolution picture of chemical interactions within the charge density framework. GBA is based on concepts from the quantum theory of atoms in molecules (QTAIM), but uses a more complete picture of the topology and geometry of the electron charge density to understand and predict bonding interactions. Gradient bundles are defined as volumes bounded by zero-flux surfaces (ZFSs) in the gradient of the charge density with well-defined energies. The structure of gradient bundles provides an avenue for detecting the locations of valence electrons, which correspond to reactive regions in a ...

  16. Failure of a MEA reclaimer tube bundle due to corrosion

    Energy Technology Data Exchange (ETDEWEB)

    Shaban, H.; Abdo, M.S.E.; Lal, D.P.


    The removal of sulphur compounds from natural gas used in ammonia production is carried out by scrubbing with monoethanol amine (MEA). To avoid build up of corrosion and degradation products, a portion of the circulating MEA solution is passed through a reclaimer. This is essentially a kettle-type reboiler with a tube bundle made of 316L stainless steel. Occasional failures of the tube bundle due to pitting corrosion have been reported. It is suggested that the excessive pitting corrosion observed on the upper rows of the tube bundle could be partly due to high steam temperature but mainly due to the liquid level falling below the tubes leaving an accumulation of corrosive degradation products on the exposed surfaces, normally these corrosive products remain diluted in the MEA solution and cause little corrosion of the covered tubes. Their concentration on the dry upper layers of the hot metal tubes, however, leads to excessive corrosion. (U.K.).

  17. Designing cooperatively folded abiotic uni- and multimolecular helix bundles (United States)

    de, Soumen; Chi, Bo; Granier, Thierry; Qi, Ting; Maurizot, Victor; Huc, Ivan


    Abiotic foldamers, that is foldamers that have backbones chemically remote from peptidic and nucleotidic skeletons, may give access to shapes and functions different to those of peptides and nucleotides. However, design methodologies towards abiotic tertiary and quaternary structures are yet to be developed. Here we report rationally designed interactional patterns to guide the folding and assembly of abiotic helix bundles. Computational design facilitated the introduction of hydrogen-bonding functionalities at defined locations on the aromatic amide backbones that promote cooperative folding into helix-turn-helix motifs in organic solvents. The hydrogen-bond-directed aggregation of helices not linked by a turn unit produced several thermodynamically and kinetically stable homochiral dimeric and trimeric bundles with structures that are distinct from the designed helix-turn-helix. Relative helix orientation within the bundles may be changed from parallel to tilted on subtle solvent variations. Altogether, these results prefigure the richness and uniqueness of abiotic tertiary structure behaviour.

  18. Horizontal gene transfer in chromalveolates

    Directory of Open Access Journals (Sweden)

    Bhattacharya Debashish


    Full Text Available Abstract Background Horizontal gene transfer (HGT, the non-genealogical transfer of genetic material between different organisms, is considered a potentially important mechanism of genome evolution in eukaryotes. Using phylogenomic analyses of expressed sequence tag (EST data generated from a clonal cell line of a free living dinoflagellate alga Karenia brevis, we investigated the impact of HGT on genome evolution in unicellular chromalveolate protists. Results We identified 16 proteins that have originated in chromalveolates through ancient HGTs before the divergence of the genera Karenia and Karlodinium and one protein that was derived through a more recent HGT. Detailed analysis of the phylogeny and distribution of identified proteins demonstrates that eight have resulted from independent HGTs in several eukaryotic lineages. Conclusion Recurring intra- and interdomain gene exchange provides an important source of genetic novelty not only in parasitic taxa as previously demonstrated but as we show here, also in free-living protists. Investigating the tempo and mode of evolution of horizontally transferred genes in protists will therefore advance our understanding of mechanisms of adaptation in eukaryotes.

  19. The concept of double bundle ACL simulation with a single bundle patellar tendon graft. A cadaveric feasibility study. (United States)

    Jacobi, Matthias; Magnussen, Robert A; Villa, Vincent; Demey, Guillaume; Neyret, Philippe


    There is significant interest in the restoration of the double-bundle anatomy of the native ACL when performing ACL reconstruction. Possible techniques include those utilizing two separate grafts with independent tunnels and those that attempt to mimic this anatomy with a single graft and fewer tunnels. Many of the latter techniques require specific instrumentation and are technically challenging. We demonstrate that the double-bundle anatomy of the native ACL can theoretically be mimicked by a single-bundle reconstruction. We performed single bundle ACL reconstruction with a bone-patellar tendon-bone (BTB) graft in two cadaveric knees. Both grafts were placed to mimic the native ACL footprints - one reconstruction was performed with rectangular bone blocks and oval tunnels and one was performed utilizing a standard BTB graft and round tunnels. Qualitative assessment of graft behavior was made as the knees were taken through a range of motion. The ACL graft was able to qualitatively mimic the behavior of the native ACL in both knees provided the bone blocks were correctly orientated. ACL reconstruction with a single BTB graft can qualitatively mimic the behavior of the two bundles of the native ACL. The key to ensuring this behavior was noted to be appropriate orientation of the graft in the tunnels. Quantitative biomechanical investigations are necessary to evaluate the impact of graft orientation on function.

  20. The concept of double bundle ACL simulation with a single bundle patellar tendon graft. A cadaveric feasibility study

    Directory of Open Access Journals (Sweden)

    Jacobi Matthias


    Full Text Available Abstract Background There is significant interest in the restoration of the double-bundle anatomy of the native ACL when performing ACL reconstruction. Possible techniques include those utilizing two separate grafts with independent tunnels and those that attempt to mimic this anatomy with a single graft and fewer tunnels. Many of the latter techniques require specific instrumentation and are technically challenging. We demonstrate that the double-bundle anatomy of the native ACL can theoretically be mimicked by a single-bundle reconstruction. Methods We performed single bundle ACL reconstruction with a bone-patellar tendon-bone (BTB graft in two cadaveric knees. Both grafts were placed to mimic the native ACL footprints – one reconstruction was performed with rectangular bone blocks and oval tunnels and one was performed utilizing a standard BTB graft and round tunnels. Qualitative assessment of graft behavior was made as the knees were taken through a range of motion. Results The ACL graft was able to qualitatively mimic the behavior of the native ACL in both knees provided the bone blocks were correctly orientated. Conclusions ACL reconstruction with a single BTB graft can qualitatively mimic the behavior of the two bundles of the native ACL. The key to ensuring this behavior was noted to be appropriate orientation of the graft in the tunnels. Quantitative biomechanical investigations are necessary to evaluate the impact of graft orientation on function.

  1. Feasibility Test of Commercial CFD Code for Thermal-Hydraulic Analysis of Wire-wrapped Fuel Pin Bundle in SFR

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Chiwoong; Ha, Kwiseok [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Haeyong, Jeong [Sejong Univ., Daejeon (Korea, Republic of)


    One of the major difficulties in the numerical approach is a grid generation of the interface between a wire and rod, because the point connectivity and higher scale deviation of a wire and rod can easily increase the number of meshes. The general way to handle this problem is a simplification of the wire-rod interface. In this study, the wire configuration effect is also studied with a no-wire case and simplified wire geometries. The materials of coolant and cladding are sodium and HT9. Fuel part is not modeled. The detailed design parameters are described in Table 1. In addition, Fig. 2 shows a detailed schematic of the fuel rod and wire. The wire contact distance, Sw, is the length penetrating the clad. Basically, the wire will be firmly contacted with the clad surface. As shown in Table 1, the wire diameter is the same as the gap between two fuel rods. However, it is unavoidable in the modeling of the wire to ignore a singular contact point between the wire and cladding. Therefore, an intersected wire and rod are arbitrarily generated. The boundary conditions for the conjugated heat transfer analysis are described in Table 2. The inlet region is defined with a uniform velocity and constant temperature of 650 K. The outlet is defined with a constant ambient pressure, i. e., zero static pressure. Since only the cladding part was modeled, a uniform heat flux condition is applied on the inner cladding wall surface. All solid surfaces are considered as no slip adiabatic boundaries. The numerical analyses of wire-wrapped 7 pins are conducted using ANSYS-CFX to check the feasibility of the CFD tool in thermal-hydraulic phenomena in a wire-wrapped fuel pin bundle. Typical turbulent models are applied to check the dependency of model selection on the pressure drop and heat transfer on the wire-wrapped fuel rod. In short, the omega-based model shows the highest pressure drop and heat transfer. Comparing the existing correlations, the pressure drop results represent

  2. Mechanical Stresses and Forces in Stereocilia Bundles of Inner and Outer Hair Cells (United States)

    Mueller, R.; Maier, H.; Boehnke, F.; Arnold, W.


    The precise mechanism of mechanoelectrical transduction in stereocilia bundles is not known. It is very difficult to measure the extremely small stresses, which occur at the stereocilia bundles. Therefore we developed 3-D finite element models of stereocilia bundles (guinea pig) to obtain quantitative results. The stereocilia bundles of the outer hair cells show a characteristic W-form. Therefore, it is interesting to compare the mechanical behavior of the stereocilia bundle of an outer hair cell with that of an inner hair cell with its linear arrangement. Our analysis provides estimates of forces and stresses on the transducer channels of mammalian hair bundles, although the model does not include active mechanisms yet.

  3. The Analysis of SBWR Critical Power Bundle Using Cobrag Code

    Directory of Open Access Journals (Sweden)

    Yohannes Sardjono


    Full Text Available The coolant mechanism of SBWR is similar with the Dodewaard Nuclear Power Plant (NPP in the Netherlands that first went critical in 1968. The similarity of both NPP is cooled by natural convection system. These coolant concept is very related with same parameters on fuel bundle design especially fuel bundle length, core pressure drop and core flow rate as well as critical power bundle. The analysis was carried out by using COBRAG computer code. COBRAG computer code is GE Company proprietary. Basically COBRAG computer code is a tool to solve compressible three-dimensional, two fluid, three field equations for two phase flow. The three fields are the vapor field, the continuous liquid field, and the liquid drop field. This code has been applied to analyses model flow and heat transfer within the reactor core. This volume describes the finitevolume equations and the numerical solution methods used to solve these equations. This analysis of same parameters has been done i.e.; inlet sub cooling 20 BTU/lbm and 40 BTU/lbm, 1000 psi pressure and R-factor is 1.038, mass flux are 0.5 Mlb/hr.ft2, 0.75 Mlb/hr.ft2, 1.00 Mlb/hr.ft2 and 1.25 Mlb/hr.ft2. Those conditions based on history operation of some type of the cell fuel bundle line at GE Nuclear Energy. According to the results, it can be concluded that SBWR critical power bundle is 10.5 % less than current BWR critical power bundle with length reduction of 12 ft to 9 ft.

  4. Learning Bundled Care Opportunities from Electronic Medical Records. (United States)

    Chen, You; Kho, Abel N; Liebovitz, David; Ivory, Catherine; Osmundson, Sarah; Bian, Jiang; Malin, Bradley A


    The traditional fee-for-service approach to healthcare can lead to the management of a patient's conditions in a siloed manner, inducing various negative consequences. It has been recognized that a bundled approach to healthcare - one that manages a collection of health conditions together - may enable greater efficacy and cost savings. However, it is not always evident which sets of conditions should be managed in a bundled manner. In this study, we investigate if a data-driven approach can automatically learn potential bundles. We designed a framework to infer health condition collections (HCCs) based on the similarity of their clinical workflows, according to electronic medical record (EMR) utilization. We evaluated the framework with data from over 16,500 inpatient stays from Northwestern Memorial Hospital in Chicago, Illinois. The plausibility of the inferred HCCs for bundled care was assessed through an online survey of a panel of five experts, whose responses were analyzed via an analysis of variance (ANOVA) at a 95% confidence level. We further assessed the face validity of the HCCs using evidence in the published literature. The framework inferred four HCCs, indicative of 1) fetal abnormalities, 2) late pregnancies, 3) prostate problems, and 4) chronic diseases, with congestive heart failure featuring prominently. Each HCC was substantiated with evidence in the literature and was deemed plausible for bundled care by the experts at a statistically significant level. The findings suggest that an automated EMR data-driven framework conducted can provide a basis for discovering bundled care opportunities. Still, translating such findings into actual care management will require further refinement, implementation, and evaluation. Copyright © 2017. Published by Elsevier Inc.

  5. Fast bundle algorithm for multiple-instance learning. (United States)

    Bergeron, Charles; Moore, Gregory; Zaretzki, Jed; Breneman, Curt M; Bennett, Kristin P


    We present a bundle algorithm for multiple-instance classification and ranking. These frameworks yield improved models on many problems possessing special structure. Multiple-instance loss functions are typically nonsmooth and nonconvex, and current algorithms convert these to smooth nonconvex optimization problems that are solved iteratively. Inspired by the latest linear-time subgradient-based methods for support vector machines, we optimize the objective directly using a nonconvex bundle method. Computational results show this method is linearly scalable, while not sacrificing generalization accuracy, permitting modeling on new and larger data sets in computational chemistry and other applications. This new implementation facilitates modeling with kernels.

  6. Cellulosic Fibers: Effect of Processing on Fiber Bundle Strength

    DEFF Research Database (Denmark)

    Thygesen, Anders; Madsen, Bo; Thomsen, Anne Belinda


    A range of differently processed cellulosic fibers from flax and hemp plants were investigated to study the relation between processing of cellulosic fibers and fiber bundle strength. The studied processing methods are applied for yarn production and include retting, scutching, carding, and cotto......A range of differently processed cellulosic fibers from flax and hemp plants were investigated to study the relation between processing of cellulosic fibers and fiber bundle strength. The studied processing methods are applied for yarn production and include retting, scutching, carding...

  7. On a Lie Algebraic Characterization of Vector Bundles

    Directory of Open Access Journals (Sweden)

    Pierre B.A. Lecomte


    Full Text Available We prove that a vector bundle π: E→M is characterized by the Lie algebra generated by all differential operators on E which are eigenvectors of the Lie derivative in the direction of the Euler vector field. Our result is of Pursell-Shanks type but it is remarkable in the sense that it is the whole fibration that is characterized here. The proof relies on a theorem of [Lecomte P., J. Math. Pures Appl. (9 60 (1981, 229-239] and inherits the same hypotheses. In particular, our characterization holds only for vector bundles of rank greater than 1.

  8. Falling film evaporation on a tube bundle with plain and enhanced tubes

    Energy Technology Data Exchange (ETDEWEB)

    Habert, M.


    The complexities of two-phase flow and evaporation on a tube bundle present important problems in the design of heat exchangers and the understanding of the physical phenomena taking place. The development of structured surfaces to enhance boiling heat transfer and thus reduce the size of evaporators adds another level of complexity to the modeling of such heat exchangers. Horizontal falling film evaporators have the potential to be widely used in large refrigeration systems and heat pumps, in the petrochemical industry and for sea water desalination units, but there is a need to improve the understanding of falling film evaporation mechanisms to provide accurate thermal design methods. The characterization of the effect of enhanced surfaces on the boiling phenomena occurring in falling film evaporators is thus expected to increase and optimize the performance of a tube bundle. In this work, the existing LTCM falling film facility was modified and instrumented to perform falling film evaporation measurements on single tube row and a small tube bundle. Four types of tubes were tested including: a plain tube, an enhanced condensing tube (Gewa-C+LW) and two enhanced boiling tubes (Turbo-EDE2 and Gewa-B4) to extend the existing database. The current investigation includes results for two refrigerants, R134a and R236fa, at a saturation temperature of T{sub sat} = 5 °C, liquid film Reynolds numbers ranging from 0 to 3000, at heat fluxes between 20 and 60 kW/m² in pool boiling and falling film configurations. Measurements of the local heat transfer coefficient were obtained and utilized to improve the current prediction methods. Finally, the understanding of the physical phenomena governing the falling film evaporation of liquid refrigerants has been improved. Furthermore, a method for predicting the onset of dry patch formation has been developed and a local heat transfer prediction method for falling film evaporation based on a large experimental database has been

  9. Anisotropy in CdSe quantum rods

    Energy Technology Data Exchange (ETDEWEB)

    Li, Liang-shi [Univ. of California, Berkeley, CA (United States)


    The size-dependent optical and electronic properties of semiconductor nanocrystals have drawn much attention in the past decade, and have been very well understood for spherical ones. The advent of the synthetic methods to make rod-like CdSe nanocrystals with wurtzite structure has offered us a new opportunity to study their properties as functions of their shape. This dissertation includes three main parts: synthesis of CdSe nanorods with tightly controlled widths and lengths, their optical and dielectric properties, and their large-scale assembly, all of which are either directly or indirectly caused by the uniaxial crystallographic structure of wurtzite CdSe. The hexagonal wurtzite structure is believed to be the primary reason for the growth of CdSe nanorods. It represents itself in the kinetic stabilization of the rod-like particles over the spherical ones in the presence of phosphonic acids. By varying the composition of the surfactant mixture used for synthesis we have achieved tight control of the widths and lengths of the nanorods. The synthesis of monodisperse CdSe nanorods enables us to systematically study their size-dependent properties. For example, room temperature single particle fluorescence spectroscopy has shown that nanorods emit linearly polarized photoluminescence. Theoretical calculations have shown that it is due to the crossing between the two highest occupied electronic levels with increasing aspect ratio. We also measured the permanent electric dipole moment of the nanorods with transient electric birefringence technique. Experimental results on nanorods with different sizes show that the dipole moment is linear to the particle volume, indicating that it originates from the non-centrosymmetric hexagonal lattice. The elongation of the nanocrystals also results in the anisotropic inter-particle interaction. One of the consequences is the formation of liquid crystalline phases when the nanorods are dispersed in solvent to a high enough

  10. Horizontal gene transfer in choanoflagellates. (United States)

    Tucker, Richard P


    Horizontal gene transfer (HGT), also known as lateral gene transfer, results in the rapid acquisition of genes from another organism. HGT has long been known to be a driving force in speciation in prokaryotes, and there is evidence for HGT from symbiotic and infectious bacteria to metazoans, as well as from protists to bacteria. Recently, it has become clear that as many as a 1,000 genes in the genome of the choanoflagellate Monosiga brevicollis may have been acquired by HGT. Interestingly, these genes reportedly come from algae, bacteria, and other choanoflagellate prey. Some of these genes appear to have allowed an ancestral choanoflagellate to exploit nutrient-poor environments and were not passed on to metazoan descendents. However, some of these genes are also found in animal genomes, suggesting that HGT into a common ancestor of choanozoans and animals may have contributed to metazoan evolution. Copyright © 2012 Wiley Periodicals, Inc.

  11. Hue geometry and horizontal connections. (United States)

    Ben-Shahar, Ohad; Zucker, Steven W


    Primate visual systems support an elaborate specialization for processing color information. Concentrating on the hue component, we observe that, contrary to Mondrian-like assumptions, hue varies in a smooth manner for ecologically important natural imagery. To represent these smooth variations, and to support those information processing tasks that utilize hue, a piecewise smooth hue field is postulated. The geometry of hue-patch interactions is developed analogously to orientation-patch interactions in texture. The result is a model for long-range (horizontal) interactions in the color domain, the power of which is demonstrated on a number of examples. Implications for computer image processing, computer vision, visual neurophysiology and psychophysics are discussed.

  12. Explorando nuevos horizontes en NASA (United States)

    Villanueva, G. L.

    A pesar de la incesante expansión del Universo iniciada con el Big Bang 14 mil millones de años atrás, nuestro Universo se siente cada día más cercano. La inquebrantable vocación de la humanidad por descubrir nuevos horizontes ha permitido el acercamiento de civilizaciones en nuestro planeta y nos ha permitido conocer nuestro lugar en el Universo como nunca antes. En este artículo presento una breve sinopsis de nuestro trabajo que se relaciona con diversas investigaciones con implicaciones astrobiológicas, desde el origen de los ingredientes de la "sopa de la vida", hasta la evolución y composición de la atmósfera de Marte.

  13. Dynamics of entangled rod-coil block copolymers (United States)

    Wang, Muzhou; Timachova, Ksenia; Alexander-Katz, Alfredo; Likhtman, Alexei E.; Olsen, Bradley D.


    Polymer science is exploring advanced materials which combine functional domains such as proteins and semiconducting polymers with traditional flexible polymers onto the same molecule. While many studies have focused on equilibrium structure-property relationships, little is known about how the conformational restrictions of rigid domains affect dynamical phenomena such as mechanical properties, processing pathways, and self-assembly kinetics. We have recently introduced a reptation theory for entangled rod-coil block copolymers as a model for this wider class of functional polymeric materials. The theory hypothesizes that the motion of rod-coils is slowed relative to rod and coil homopolymers because of a mismatch between the curvature of the rod and coil entanglement tubes. This effect leads to activated reptation and arm retraction as two relaxation mechanisms that govern the short and long rod regimes, respectively. These results were verified by tracer diffusion measurements using molecular dynamics simulation and forced Rayleigh scattering in both the rod-coil diblock and coil-rod-coil triblock configurations. The tracer diffusion results were then compared to experimental self-diffusion measurements which require a consideration of the motion of the surrounding chains.

  14. Numerical simulation of the sucker-rod pumping system

    Directory of Open Access Journals (Sweden)

    Oldrich Joel Romero


    Full Text Available The sucker rod pump is an artificial lift method frequently applied in onshore petroleum wells. This system can be described using a numerical simulation based on the behavior of a rod string. In the past, the elastic behavior of the rod string made it difficult to model the system. However, since the 1960s and with the advent of digital computers, it has been modeled numerically. The rod string be-haves like a slender bar, and thus, the propagation of elastic waves along the bar can be represented by a one-dimensional equation. Gibbs (1963 presented a mathematical model based on the wave equation, which is described on the basis of the analysis of forces on the rod string and is incorporated into a boundary value problem involving partial differential equations. The use of the finite differ-ence method allows for a numerical solution by the discretization of the wave equation developed in the mathematical formulation with appropriate boundary and initial conditions. This work presents a methodology for implementing an academic computer code that allows simulation of the upstroke and downstroke motion of the rod string described by the wave equation under ideal operating conditions, assuming a harmonic motion of the rod at one end and downhole pump at the other end. The goal of this study is to generate the downhole dynamometer card, an important and consolidated tool that controls the pump system by diagnosing oper-ational conditions of the downhole pump.


    Directory of Open Access Journals (Sweden)

    N. Börlin


    Full Text Available The aim of this paper is to investigate whether the Matlab-based Damped Bundle Adjustment Toolbox (DBAT can be used to provide independent verification of the BA computation of two popular software—PhotoModeler (PM and PhotoScan (PS. For frame camera data sets with lens distortion, DBAT is able to reprocess and replicate subsets of PM results with high accuracy. For lens-distortion-free data sets, DBAT can furthermore provide comparative results between PM and PS. Data sets for the discussed projects are available from the authors. The use of an external verification tool such as DBAT will enable users to get an independent verification of the computations of their software. In addition, DBAT can provide computation of quality parameters such as estimated standard deviations, correlation between parameters, etc., something that should be part of best practice for any photogrammetric software. Finally, as the code is free and open-source, users can add computations of their own.

  16. Development for analysis system of rods enrichment of nuclear fuels; Desarrollo de un sistema de analisis de enriquecimiento de barras de combustible nuclear

    Energy Technology Data Exchange (ETDEWEB)

    Rojas C, E.L


    Nuclear industry is strongly regulated all over the world and quality assurance is important in every nuclear installation or process related with it. Nuclear fuel manufacture is not the exception. ININ was committed to manufacture four nuclear fuel bundles for the CFE nucleo electric station at Laguna Verde, Veracruz, under General Electric specifications and fulfilling all the requirements of this industry. One of the quality control requisites in nuclear fuel manufacture deals with the enrichment of the pellets inside the fuel bundle rods. To achieve the quality demanded in this aspect, the system described in this work was developed. With this system, developed at ININ it is possible to detect enrichment spikes since 0.4 % in a column of pellets with a 95 % confidence interval and to identify enrichment differences greater than 0.2 % e between homogeneous segments, also with a 95 % confidence interval. ININ delivered the four nuclear fuel bundles to CFE and these were introduced in the core of the nuclear reactor of Unit 1 in the fifth cycle. Nowadays they are producing energy and have shown a correct mechanical performance and neutronic behavior. (Author)

  17. Innovative Defense Acquisition Concept Deployer Equipment Bundle (DEB) (United States)


    METHODOLOGY This project reviewed a substantial amount of literature , to include applicable concept plans, memorandums, cost benefit analyses, organizational...NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA MBA PROFESSIONAL REPORT INNOVATIVE DEFENSE ACQUISITION CONCEPT DEPLOYER...ACQUISITION CONCEPT DEPLOYER EQUIPMENT BUNDLE (DEB) 5. FUNDING NUMBERS 6. AUTHOR(S) Frederic Albesa, Isaac J. Ortman, and Stephen F. Kirouac 7

  18. Temperature response of bundle-sheath conductance in maize leaves

    NARCIS (Netherlands)

    Yin, Xinyou; Putten, Van Der Peter E.L.; Struik, Paul C.; Driever, Steven M.


    A small bundle-sheath conductance (g bs) is essential for the C4 CO2-concentrating mechanism to suppress photorespiration effectively. To predict the productivity of C4 crops accurately under global warming, it is necessary to examine whether and how g

  19. Quillen bundle and geometric prequantization of non-abelian ...

    Indian Academy of Sciences (India)

    E-mail:;; MS received 7 September 2010; revised 23 November 2010. Abstract. In this paper we prequantize the moduli space of non-abelian vortices. We explicitly calculate the symplectic form arising from L2 metric and we construct a prequantum line bundle ...

  20. Metallic/semiconducting ratio of carbon nanotubes in a bundle ...

    Indian Academy of Sciences (India)

    SWCNTs) in a bundle by resonant Raman spectroscopy. The calculation has been done for the three peak positions in radial breathing mode (RBM) spectra obtained by using a laser excitation wavelength () of 633 nm from He–Ne laser on ...

  1. The fibre bundle anatomy of human cruciate ligaments

    NARCIS (Netherlands)

    Mommersteeg, T. J.; Kooloos, J. G.; Blankevoort, L.; Kauer, J. M.; Huiskes, R.; Roeling, F. Q.


    The cruciate ligaments of the knee consist of numerous fascicles, groups of which comprise fibre bundles. The stabilising function of these ligaments is established by changes in the lengths and orientations of the fascicles. Understanding the function of knee ligaments thus requires an

  2. Metabolic profiling of laser microdissected vascular bundles of Arabidopsis thaliana

    Directory of Open Access Journals (Sweden)

    Fiehn Oliver


    Full Text Available Abstract Background Laser microdissection is a useful tool for collecting tissue-specific samples or even single cells from animal and plant tissue sections. This technique has been successfully employed to study cell type-specific expression at the RNA, and more recently also at the protein level. However, metabolites were not amenable to analysis after laser microdissection, due to the procedures routinely applied for sample preparation. Using standard tissue fixation and embedding protocols to prepare histological sections, metabolites are either efficiently extracted by dehydrating solvents, or washed out by embedding agents. Results In this study, we used cryosectioning as an alternative method that preserves sufficient cellular structure while minimizing metabolite loss by excluding any solute exchange steps. Using this pre-treatment procedure, Arabidopsis thaliana stem sections were prepared for laser microdissection of vascular bundles. Collected samples were subsequently analyzed by gas chromatography-time of flight mass spectrometry (GC-TOF MS to obtain metabolite profiles. From 100 collected vascular bundles (~5,000 cells, 68 metabolites could be identified. More than half of the identified metabolites could be shown to be enriched or depleted in vascular bundles as compared to the surrounding tissues. Conclusion This study uses the example of vascular bundles to demonstrate for the first time that it is possible to analyze a comprehensive set of metabolites from laser microdissected samples at a tissue-specific level, given that a suitable sample preparation procedure is used.

  3. AdS 3-manifolds and Higgs bundles

    DEFF Research Database (Denmark)

    Alessandrini, Daniele; Li, Qiongling


    In this paper we investigate the relationships between closed AdS $3$-manifolds and Higgs bundles. We have a new way to construct AdS structures that allows us to see many of their properties explicitly, for example we can recover the very recent formula by Tholozan for their volume. We give natu...

  4. Fission yeast Scp3 potentially maintains microtubule orientation through bundling.

    Directory of Open Access Journals (Sweden)

    Kanako Ozaki

    Full Text Available Microtubules play important roles in organelle transport, the maintenance of cell polarity and chromosome segregation and generally form bundles during these processes. The fission yeast gene scp3+ was identified as a multicopy suppressor of the cps3-81 mutant, which is hypersensitive to isopropyl N-3-chlorophenylcarbamate (CIPC, a poison that induces abnormal multipolar spindle formation in higher eukaryotes. In this study, we investigated the function of Scp3 along with the effect of CIPC in the fission yeast Schizosaccharomyces pombe. Microscopic observation revealed that treatment with CIPC, cps3-81 mutation and scp3+ gene deletion disturbed the orientation of microtubules in interphase cells. Overexpression of scp3+ suppressed the abnormal orientation of microtubules by promoting bundling. Functional analysis suggested that Scp3 functions independently from Ase1, a protein largely required for the bundling of the mitotic spindle. A strain lacking the ase1+ gene was more sensitive to CIPC, with the drug affecting the integrity of the mitotic spindle, indicating that CIPC has a mitotic target that has a role redundant with Ase1. These results suggested that multiple systems are independently involved to ensure microtubule orientation by bundling in fission yeast.


    Directory of Open Access Journals (Sweden)

    E. N. Pavlyukova


    Full Text Available Tissue Doppler imaging is evolving as a useful echocardiographic tool for quantitative assessment of left ventricular systolic and diastolic function. Over the last 10 years, myocardial deformation imaging has become possible initially with tissue Doppler , and more recently with myocardial speckle-tracking using 2D echocardiography. Unlike simple tissue velocity measurements, deformation measurements are specific for the region of interest. Strain rate or strain measurements have been used as sensitive indicators for subclinical diseases, and it is the most widely used tool to assess mechanical dyssynchrony. Left bundle branch block is a frequent, etiologically heterogeneous, clinically hostile and diagnostically challenging entity. About 2% of patients underwent cardiac stress testing show stable or intermittent left bundle branch block. Presence of left bundle branch block is associated with a lower and slower diastolic coronary flow velocity especially during hyperemia. Stress echocardiography is the best option for the diagnosis of ischemic heart disease, albeit specificity and sensitivity reduce in patients with left bundle branch block in the territory of left anterior descending artery in presence of initial septum dyskinesia.

  6. Anatomic Double-Bundle Anterior Cruciate Ligament Reconstruction

    NARCIS (Netherlands)

    Hofbauer, Marcus; Muller, Bart; Wolf, Megan; Forsythe, Brian; Fu, Freddie H.


    Over the past decade, intense research of the function of the 2 distinct bundles, the anteromedial and posterolateral, of the anterior cruciate ligament (ACL) has led to pronounced changes in the technical concepts of ACL reconstruction. Recently, the renewed focus of ACL reconstruction has been to

  7. Reminiscences Of The First His Bundle Electrography In India

    Directory of Open Access Journals (Sweden)

    Nambiar C.A


    Full Text Available Dr Onkar Narula was making a huge wave those days with his work on His Bundle Electrocardiography and Corrected Sinus Node Recovery Time. He visited us in late 1972 or early 1973,probably the latter date. Till then venous catheterizations (including pacing were done by open cut down. I remember the first time we used venous sheath through right femoral vein. Dr Bhatia was the operator and I was assisting him and Dr Savithri Srivasthava was the senior Registrar. With Dr Narula showing the way we did the first His Bundle Recording and I analysed the whole roll manually as was the method those days. We had to improvise a junction box as the recording equipment did not have a proper connecting accessory at that time. After Dr Narula left we did His Bundle recording on many more patients and undertook a study. This was published as: Effect of acute digitalization on His Bundle Intervals and Corrected Sinus Node Recovery Time in young adults.M.L.Bhatia,C.Ashokan Nambiar,S.Shrivastava and Sujoy B.Roy: Indian Heart Journal:Vol-2:1977.1The article was received for publication on 29/11/1973 as acknowledged underneath, but strangely it took a long time to come in print. I have preserved some of the cath rolls and reprint of the article.

  8. Frobenius pull backs of vector bundles in higher dimensions

    Indian Academy of Sciences (India)

    ... of a Frobenius pull back of is a refinement of the Frobenius pull back of the Harder–Narasimhan filtration of , provided there is a lower bound on the characteristic (in terms of rank of and the slope of the destabilizing sheaf of the cotangent bundle of ). We also recall some examples, due to Raynaud and Monsky, ...

  9. The Roach muscle bundle and umbilical cord coiling

    NARCIS (Netherlands)

    de Laat, Monique W. M.; Nikkels, Peter G. J.; Franx, Arie; Visser, Gerard H. A.


    To determine if presence of the Roach muscle, a small muscle bundle lying just beside the umbilical artery, contributes to umbilical cord coiling. 251 umbilical cords were examined. The umbilical coiling index (UCI) was calculated as the number of coils divided by the cord length in cm. Cords were

  10. Subanalytic bundles and tubular neighbourhoods of zero-loci

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    Abstract. We introduce the natural and fairly general notion of a subanalytic bundle. (with a finite dimensional vector space P of sections) on a subanalytic subset X of a real analytic manifold M, and prove that when M is compact, there is a Baire subset U of sections in P whose zero-loci in X have tubular neighbourhoods, ...

  11. On the classification of complex vector bundles of stable rank

    Indian Academy of Sciences (India)

    This classification becomes more effective on generalized flag manifolds, where the Lie algebra formalism and concrete integrability conditions describe in constructive terms the Chern classes of a vector bundle. ... Since deceased; Mathematics Department, University of California, Santa Barbara, CA 93106, USA ...

  12. On infinitesimal conformal transformations of the tangent bundles ...

    Indian Academy of Sciences (India)

    The metric. ˜g, which is called a synectic lift of the Riemannian metric g, was introduced by Talantova and Shirokov [4] to study the differential geometry of tangent bundles of Riemannian manifolds (for details, also see [5]). Their paper is concerned with the geometry of the space of n dual variables. The concept of a dual ...

  13. On the classification of complex vector bundles of stable rank

    Indian Academy of Sciences (India)

    According to previous observations, this would imply (under the above torsion conditions) a classification of all rank r complex vector bundles on X, for stable rank r ≥ n/2. A few partial answers to this question are known. For instance, a classical result of. Wu asserts that any couple of cohomology classes (c1,c2) ∈ H2(X, ...

  14. Thermal-recovery of modal instability in rod fiber amplifiers

    DEFF Research Database (Denmark)

    Jørgensen, Mette Marie; Laurila, Marko; Noordegraaf, Danny


    We investigate the temporal dynamics of Modal instabilities (MI) in ROD fiber amplifiers using a 100 μm core rod fiber in a single-pass amplifier configuration, and we achieve ~200W of extracted output power before the onset of MI. Above the MI threshold, we investigate the temporal dynamics of b...... and thermally annealed between each test series. We find that the MI threshold degrades as it is reached multiple times, but is recovered by thermal annealing. We also find that the test history of the rods affects the temporal dynamics....

  15. Plasmonic rod dimers as elementary planar chiral meta-atoms

    CERN Document Server

    Zhukovsky, Sergei V; Chigrin, Dmitry N


    Electromagnetic response of metallic rod dimers is theoretically calculated for arbitrary planar arrangement of rods in the dimer. It is shown that dimers without an in-plane symmetry axis exhibit elliptical dichroism and act as "atoms" in planar chiral metamaterials. Due to a very simple geometry of the rod dimer, such planar metamaterials are much easier in fabrication than conventional split-ring or gammadion-type structures, and lend themselves to a simple analytical treatment based on coupled dipole model. Dependencies of metamaterial's directional asymmetry on the dimer's geometry are established analytically and confirmed in numerical simulations.

  16. Review of FFTF and CRBRP control rod systems designs

    Energy Technology Data Exchange (ETDEWEB)

    Pitterle, T. A.; Lagally, H. O.


    The evolution of the primary control rod system design for FFTF and CRBR, beginning with the initial choice of the basic concepts, is described. The significant component and systems tests are reviewed together with the test results which referenced the development of the CRBR primary control rod system design. Modifications to the concepts and detail designs of the FFTF control rod system were required principally to satisfy the requirements of CRBR, and at the same time incorporating design refinements shown desirable by the tests.

  17. A case of ‘Masquerading’ bundle branch block: A forgotten concept


    Dinesh Choudhary; Narayanan Namboodiri; Jaganmohan A. Tharakan


    ‘Masquerading’ bundle branch block (right bundle branch block in the precordial leads with left bundle branch block in frontal leads and left axis deviation) is seen most commonly with coronary artery disease and hypertension. No definite explanation is available so far for these changes. We are presenting a case of rare congenital intranuclear inclusion myopathy with congestive heart failure and ‘Masquerading’ bundle branch block in ECG.

  18. Structural Causes of Right Bundle Branch Block?Time for a Closer Look?


    Ker, James


    Right bundle branch block is an electrocardiographic phenomenon with specific criteria. Currently, two specific forms of right bundle branch block are acknowledged, a proximal and a distal variant. A vast array of pathologies can cause proximal, distal or even combined forms of right bundle branch block. In this study it is suggested that a third type of right bundle branch block exist: one caused by a subaortic muscular tendon in the left ventricle, leading to an increased velocity of conduc...

  19. Gas reservoir evaluation for underbalanced horizontal drilling

    National Research Council Canada - National Science Library

    Li Gao; Meng Ying-Feng; Wei Na; Xu Zhao-Yang; Li Hong-Tao; Xiao Gui-Lin; Zhang Yu-Rui


    .... Based on drilling operation parameters, well structure and monitored parameters, the wellbore pressure and the gas reservoir permeability could be predicted theoretically for underbalanced horizontal drilling...

  20. Lower complication rates for cranioplasty with peri-operative bundle. (United States)

    Le, Catherine; Guppy, Kern H; Axelrod, Yekaterina V; Hawk, Mark W; Silverthorn, James; Inacio, Maria C; Akins, Paul T


    The overall benefits of craniectomy must include procedural risks from cranioplasty. Cranioplasty carries a high risk of surgical site infections (SSI) particularly with antibiotic resistant bacteria. The goal of this study was to measure the effect of a cranioplasty bundle on peri-operative complications. The authors queried a prospective, inpatient neurosurgery database at Kaiser Sacramento Medical Center for craniectomy and cranioplasty over a 7 year period. 57 patients who underwent cranioplasties were identified. A retrospective chart review was completed for complications, including surgical complications such as SSI, wound dehiscence, and re-do cranioplasty. We measured cranioplasty complication rates before and after implementation of a peri-operative bundle, which consisted of peri-operative vancomycin (4 doses), a barrier dressing through post-operative day (POD) 3, and de-colonization of the surgical incision using topical chlorhexidine from POD 4 to 7. The rate of MRSA colonization in cranioplasty patients is three times higher than the average seen on ICU admission screening (19% vs. 6%). The cranioplasty surgical complication rate was 22.8% and SSI rate was 10.5%. The concurrent SSI rate for craniectomy was 1.9%. Organisms isolated were methicillin-resistant Staphylococcus aureus (4), methicillin-sensitive S. aureus (1), Propionibacterium acnes (1), and Escherichia coli (1). Factors associated with SSI were peri-operative vancomycin (68.6% vs. 16.7%, p=0.0217). Complication rates without (n=21) and with (n=36) the bundle were: SSI (23.8% vs. 2.8%, p=0.0217) and redo cranioplasty (19% vs. 0%, p=0.0152). Bundle use did not affect rates for superficial wound dehiscence, seizures, or hydrocephalus. The cranioplasty bundle was associated with reduced SSI rates and the need for re-do cranioplasties. Copyright © 2014 Elsevier B.V. All rights reserved.

  1. Early Results of Anatomic Double Bundle Anterior Cruciate Ligament Reconstruction

    Directory of Open Access Journals (Sweden)

    Demet Pepele


    Full Text Available Aim: The goal in anterior cruciate ligament reconstruction (ACLR is to restore the normal anatomic structure and function of the knee. In the significant proportion of patients after the traditional single-bundle ACLR, complaints of instability still continue. Anatomic double bundle ACLR may provide normal kinematics in knees, much closer to the natural anatomy. The aim of this study is to clinically assess the early outcomes of our anatomical double bundle ACLR. Material and Method: In our clinic between June 2009 and March 2010, performed the anatomic double bundle ACLR with autogenous hamstring grafts 20 patients were evaluated prospectively with Cincinnati, IKDC and Lysholm scores and in clinically for muscle strength and with Cybex II dynamometer. Results: The mean follow-up is 17.8 months (13-21 months. Patients%u2019 scores of Cincinnati, IKDC and Lysholm were respectively, preoperative 18.1, 39.3 and 39.8, while the post-op increased to 27.2, 76.3 and 86.3. In their last check, 17 percent of the patients according to IKDC scores (85% A (excellent and B (good group and 3 patients took place as C (adequate group. The power measurements of quadriceps and hamstring muscle groups of patients who underwent surgery showed no significant difference compared with the intact knees. Discussion: Double-bundle ACL reconstruction is a satisfactory method. There is a need comparative, long-term studies in large numbers in order to determine improving clinical outcome, preventing degeneration and restoring the knee biomechanics better.

  2. The determinant bundle on the moduli space of stable triples over a ...

    Indian Academy of Sciences (India)

    We construct a holomorphic Hermitian line bundle over the moduli space of stable triples of the form (1, 2, ), where 1 and 2 are holomorphic vector bundles over a fixed compact Riemann surface , and : 2 → 1 is a holomorphic vector bundle homomorphism. The curvature of the Chern connection of this ...

  3. Lexical Bundles in Chinese Undergraduate Academic Writing at an English Medium University (United States)

    Ruan, Zhoulin


    This paper investigates the use of lexical bundles in Chinese students' academic writing across different levels of studies at an English medium university. Frequency-based bundles were retrieved from a corpus of student academic texts written at four points of time between Year 1 and Year 4, and the structures and functions of the bundles were…

  4. High-yield production of hydrophobins RodA and RodB from Aspergillus fumigatus in Pichia pastoris

    DEFF Research Database (Denmark)

    Pedersen, Mona Højgaard; Borodina, Irina; Moresco, Jacob Lange


    broth. Protein bands of expected sizes were detected by SDS-PAGE and western blotting, and the identity was further confirmed by tandem mass spectrometry. Both proteins were purified using his-affinity chromatography, and the high level of purity was verified by silver-stained SDS-PAGE. Recombinant Rod...... RodA showed a similar ability to emulsify air in water, while recombinant RodB could also emulsify oil in water better than the control protein bovine serum albumin (BSA). This is to our knowledge the first successful expression of hydrophobins from A. fumigatus in a eukaryote host, which makes...

  5. Synthesis of homochiral tris-indanyl molecular rods

    DEFF Research Database (Denmark)

    Kjeldsen, Niels Due; Funder, Erik Daa; Gothelf, Kurt Vesterager


    Homochiral tris-indanyl molecular rods designed for supramolecular surface self-assembly were synthesized. The chiral indanol moiety was constructed via a Ti-mediated alkyne trimerization. Further manipulations resulted in a homochiral indanol monomer. This was employed as the precursor for succe......Homochiral tris-indanyl molecular rods designed for supramolecular surface self-assembly were synthesized. The chiral indanol moiety was constructed via a Ti-mediated alkyne trimerization. Further manipulations resulted in a homochiral indanol monomer. This was employed as the precursor...... for successive Sonogashira and Ohira-Bestman reactions towards the homochiral tris-indanyl molecular rods. The molecular rods will be applied for scanning tunnelling microscopy studies of their surface self-assembly and chirality....

  6. Motion simulation of hydraulic driven safety rod using FSI method

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Jaeho; Kim, Sanghaun; Yoo, Yeonsik; Cho, Yeonggarp; Kim, Jong In [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    Hydraulic driven safety rod which is one of them is being developed by Division for Reactor Mechanical Engineering, KAERI. In this paper the motion of this rod is simulated by fluid structure interaction (FSI) method before manufacturing for design verification and pump sizing. A newly designed hydraulic driven safety rod which is one of reactivity control mechanism is simulated using FSI method for design verification and pump sizing. The simulation is done in CFD domain with UDF. The pressure drop is changed slightly by flow rates. It means that the pressure drop is mainly determined by weight of moving part. The simulated velocity of piston is linearly proportional to flow rates so the pump can be sized easily according to the rising and drop time requirement of the safety rod using the simulation results.

  7. Vibrations of post-buckled rods: The singular inextensible limit

    KAUST Repository

    Neukirch, Sébastien


    The small-amplitude in-plane vibrations of an elastic rod clamped at both extremities are studied. The rod is modeled as an extensible, shearable, planar Kirchhoff elastic rod under large displacements and rotations, and the vibration frequencies are computed both analytically and numerically as a function of the loading. Of particular interest is the variation of mode frequencies as the load is increased through the buckling threshold. While for some modes there are no qualitative changes in the mode frequencies, other frequencies experience rapid variations after the buckling threshold, the thinner the rod, the more abrupt the variations. Eventually, a mismatch for half of the frequencies at buckling arises between the zero thickness limit of the extensible model and the inextensible model. © 2011 Elsevier Ltd. All rights reserved.

  8. The ATLAS LARG ROD G-Links Cooling System

    CERN Document Server

    Hubaut, F; Repain, P; Rossel, F; Vincent, D


    In this note is described the water cooling system that will be implemented on the ROD boards of the liquid argon calorimeter detectors in order to guarantee a proper behavior of the optical reception of the data.

  9. Oscillation of a rigid rod in the special relativity

    CERN Document Server

    Paiva, F M


    In the special relativity, a rigid rod slides upon itself, with one extremity oscillating harmonically. We discovered restrictions in the amplitude of the motion and in the length of the rod, essential to eliminate unphysical solutions. ------- Cxe la speciala relativeco, rigida stango movigxas sur si mem, kun unu fino oscilante harmonie. Ni malkovris limigajn kondicxojn pri la amplitudo de movado kaj pri la longo de stango, necesegaj por elimini ne-fizikajn solvojn.

  10. Apparatus for injection casting metallic nuclear energy fuel rods (United States)

    Seidel, Bobby R.; Tracy, Donald B.; Griffiths, Vernon


    Molds for making metallic nuclear fuel rods are provided which present reduced risks to the environment by reducing radioactive waste. In one embodiment, the mold is consumable with the fuel rod, and in another embodiment, part of the mold can be re-used. Several molds can be arranged together in a cascaded manner, if desired, or several long cavities can be integrated in a monolithic multiple cavity re-usable mold.

  11. Colloidal rods and spheres in partially miscible binary liquids


    Hijnen, Niek


    Different scenarios for assembling rod-like and spherical colloidal particles using binary mixtures of partially miscible liquids were investigated experimentally. Suitable rod-like colloids were developed first. The subsequent studies of colloids in binary liquids consisted, on one hand, of systems where particles were partially wetted by both phases and, on the other hand, of systems where particles were completely wetted by the minority phase. A simple method to prepare l...

  12. Estimating modal instability threshold for photonic crystal rod fiber amplifiers

    DEFF Research Database (Denmark)

    Johansen, Mette Marie; Hansen, Kristian Rymann; Laurila, Marko


    We present a semi-analytic numerical model to estimate the transverse modal instability (TMI) threshold for photonic crystal rod amplifiers. The model includes thermally induced waveguide perturbations in the fiber cross section modeled with finite element simulations, and the relative intensity ...... noise (RIN) of the seed laser, which seeds mode coupling between the fundamental and higher order mode. The TMI threshold is predicted to ~370 W – 440 W depending on RIN for the distributed modal filtering rod fiber....

  13. Horizontal vortex single chamber hydroturbine

    Directory of Open Access Journals (Sweden)

    Sergio Antonio Zarate-Orrego


    Full Text Available Se evaluó una máquina con alta resistencia de forma para extraer energía de una quebrada, río o corriente marina, y generar electricidad. Sin instrumentos adecuados, la investigación fue cualitativa. Se supuso que si aun así funcionaba, su comportamiento podía mejorar suavizándose la forma. El aparato tiene una tobera semi-convergente de paredes planas, una cámara de vórtice cilíndrica y un rodete. Capta agua por su sección mayor y la descarga tangencialmente por su sección menor en la cámara de vórtice; ésta tiene un orificio en una de sus paredes laterales. Así forma un vórtice horizontal que hace girar un rodete cuyo eje acciona un generador eléctrico. El trabajo experimental realizado mostró que sí es posible producir energía eléctrica con este dispositivo pese a las condiciones adversas en que se ensayó.

  14. Biomechanical comparisons of knee stability after anterior cruciate ligament reconstruction between 2 clinically available transtibial procedures: anatomic double bundle versus single bundle. (United States)

    Kondo, Eiji; Merican, Azhar M; Yasuda, Kazunori; Amis, Andrew A


    Several trials have compared the clinical results between anatomic double-bundle and single-bundle anterior cruciate ligament reconstruction procedures. However, it remains controversial whether the anatomic double-bundle procedure is superior to the single-bundle procedure. The anatomic double-bundle procedure will be better than the single-bundle procedure at resisting anterior laxity, internal rotation laxity, and pivot-shift instability. Controlled laboratory study. Eight cadaveric knees were tested in a 6 degrees of freedom rig using the following loading conditions: 90-N anterior tibialforce, 5-N.m internal and external tibial torques, and a simulated pivot-shift test. Tibiofemoral kinematics during the flexion-extension cycle were recorded with an optical tracking system for (1) intact, (2) anterior cruciate ligament-deficient knee, (3) anatomic double-bundle reconstruction, and (4) single-bundle reconstruction placed at 11 o'clock in the intercondylar notch. There were significant reductions of anterior laxity of 3.5 mm at 20 degrees of flexion, internal rotational laxity of 2.5 degrees at 20 degrees of flexion, and anterior translations (2 mm) and internal rotations (5 degrees ) in the simulated pivot-shift test in the double-bundle reconstruction com-pared with the single-bundle reconstruction. There were no significant differences between the 2 procedures for external rotation laxity. The postoperative anterior translation and internal rotation stability after anatomic double-bundle anterior cruciate ligament reconstruction were significantly better than after single-bundle reconstruction, in both static tests and the pivot shift. Unlike previous laboratory studies, this work used clinical arthroscopic methods for anterior cruciate ligament reconstruction, and found that the anatomic reconstruction was superior to a single graft placed at 11 o'clock.

  15. Performance of the NRX shut-off rods

    Energy Technology Data Exchange (ETDEWEB)

    Manson, R.E.


    A new type of shut-off rod of electromechanical design was developed by the American Machine and Foundry Company for use in the NRX reactor following the accident of 1952. The new rods were installed in May, 1956, as part of the control system conversion program which was completed in 1958. Some problems were encountered with limit switch adjustment but minor modifications in design led to much improved operation. he performance of the rods also improved as more experience was gained in the maintenance and adjustment of the various headgear components. Each headgear is now overhauled once a year on a routine basis. The present design of shut-off rod is considered to be very satisfactory. There has only been one occasion when a shut-off rod has failed to come fully down on a trip. Rods have failed to operate correctly on five other occasions but these occurred during shutdown periods or when the reactor was being shutdown manually. (author)

  16. Toggle rod stabilisation of coxofemoral luxation in 14 cats. (United States)

    Pratesi, A; Grierson, J; Moores, A P


    To describe the surgical technique and to report outcomes in cats with coxofemoral luxation treated with open reduction and toggle rod stabilisation. Retrospective study of cats with coxofemoral luxation stabilised via the toggle rod method. Short-term follow-up included clinical examination and radiographs. Long-term follow-up was via owner questionnaire. Fourteen cats were included. All of the cats had reported unilateral craniodorsal hip luxation. Nine cats (64·3%) had additional orthopaedic injuries. Luxations were stabilised with a 3·2-mm toggle rod (2·7-mm toggle rod in one cat) and two loops of four-metric polydioxanone (five-metric polydioxanone in one cat and three loops of four-metric polydioxanone in two cats). Success rate, in terms of maintenance of reduction, was 86%. Reluxation occurred in two cats (14%), both of which had multiple limb injuries. Eleven owner questionnaires (mean follow-up time 15·5 months) reported a functional outcome of "very good" to "excellent". Although the diameter of the pelvic canal was reduced by the presence of the toggle rod (mean narrowing 16.2%), none of the cats had defaecatory issues. Toggle rod stabilisation is an effective method for the treatment of coxofemoral luxation in cats. Injuries to multiple limbs may be a risk factor for reluxation. © 2012 British Small Animal Veterinary Association.

  17. Vibrational Power Flow Analysis of Rods and Beams (United States)

    Wohlever, James Christopher; Bernhard, R. J.


    A new method to model vibrational power flow and predict the resulting energy density levels in uniform rods and beams is investigated. This method models the flow of vibrational power in a manner analogous to the flow of thermal power in a heat conduction problem. The classical displacement solutions for harmonically excited, hysteretically damped rods and beams are used to derive expressions for the vibrational power flow and energy density in the rod and beam. Under certain conditions, the power flow in these two structural elements will be shown to be proportional to the energy density gradient. Using the relationship between power flow and energy density, an energy balance on differential control volumes in the rod and beam leads to a Poisson's equation which models the energy density distribution in the rod and beam. Coupling the energy density and power flow solutions for rods and beams is also discussed. It is shown that the resonant behavior of finite structures complicates the coupling of solutions, especially when the excitations are single frequency inputs. Two coupling formulations are discussed, the first based on the receptance method, and the second on the travelling wave approach used in Statistical Energy Analysis. The receptance method is the more computationally intensive but is capable of analyzing single frequency excitation cases. The traveling wave approach gives a good approximation of the frequency average of energy density and power flow in coupled systems, and thus, is an efficient technique for use with broadband frequency excitation.

  18. Commissioning of a passive rod scanner at INB

    Energy Technology Data Exchange (ETDEWEB)

    Junqueira, Fabio da Silva; Oliveira, Carlos A.; Palheiros, Franklin, E-mail:, E-mail: [Industrias Nucleares do Brasil (INB), Resende, RJ (Brazil). Superintendencia de Engenharia do Combustivel; Fernandez, Pablo Jesus Piñer, E-mail: [Tecnatom, San Sebastian de los Reyes, Madrid (Spain)


    For the 21st reload for Angra 1, a shift from Standard to Advanced fuel design will be introduced, where the fuel assemblies under the new design will contain fuel rods with axial blanket, in line with ELETRONUCLEAR's requirement for a higher energy efficient reactor fuel. Additionally, fuel rods for Angra 2 and 3, using gadolinium type burnable poison, have to be submitted to inspections due to the demand for the same type of inspection, which cannot be certified at INB currently. In keeping with CNEN regulations, every fuel-assembly component must be inspected and certified by a qualified method. Nevertheless, INB lacks the means to perform the certification-required inspection aimed at determining the uranium enrichment and presence of gadolinium pellets inside the closed rods. Hence, the use is necessary of a scanner capable of inspecting differently enriched fuel rods and/or gadolinium pellets (axial blanket). This work aims to present the recent Passive Rod Scanner installed at INB with most advance technology in the area, making possible to completely fulfill Angra 1, 2 and 3 rods inspection at INB Resende site. (author)

  19. Horizontal cooperation in logistics : Opportunities and impediments

    NARCIS (Netherlands)

    Cruijssen, Frans; Cools, Martine; Dullaert, Wout

    This paper presents the results of a large-scale survey on the potential benefits of and impediments for horizontal cooperation in Flanders. The main findings are that in general Logistics Service Providers strongly believe in the potential benefits of horizontal cooperation to increase their

  20. Rectifying Horizontal Inequalities: Lessons from African Conflict ...

    African Journals Online (AJOL)

    One of the most prevalent and underrepresented root causes of conflict in Africa and worldwide is that of horizontal inequalities. In that light, the goal of this paper is to provide practical solutions for the long-term resolution of conflict by addressing one of its root causes, that of horizontal inequalities. Reference will be made ...

  1. Rectifying Horizontal Inequalities: Lessons from African Conflict

    African Journals Online (AJOL)

    and horizontal (between groups) inequalities. A number of scholars have addressed the question of inequalities. Frances Stewart, for example, deals with the problem of horizontal inequalities in a number of papers.2 Stewart. (2002:3) argues that 'unequal access to political/economic/social resources. 1 The social contract ...

  2. Do infants have the horizontal bias?

    NARCIS (Netherlands)

    van Renswoude, D.R.; Johnson, S.P.; Raijmakers, M.E.J.; Visser, I.


    A robust set of studies show that adults make more horizontal than vertical and oblique saccades, while scanning real-world scenes. In this paper we study the horizontal bias in infants. The directions of eye movements were calculated for 41 infants (M = 8.40 months, SD = 3.74, range = 3.48–15.47)

  3. The Process of Horizontal Differentiation: Two Models. (United States)

    Daft, Richard L.; Bradshaw, Patricia J.


    Explores the process of horizontal differentiation by examining events leading to the establishment of 30 new departments in five universities. Two types of horizontal differentiation processes--administrative and academic--were observed and each was associated with different organizational conditions. (Author/IRT)

  4. Rod internal pressure quantification and distribution analysis using Frapcon

    Energy Technology Data Exchange (ETDEWEB)

    Jessee, Matthew Anderson [ORNL; Wieselquist, William A [ORNL; Ivanov, Kostadin [Pennsylvania State University, University Park


    This report documents work performed supporting the Department of Energy (DOE) Office of Nuclear Energy (NE) Fuel Cycle Technologies Used Fuel Disposition Campaign (UFDC) under work breakdown structure element, ST Analysis. In particular, this report fulfills the M4 milestone M4FT- 15OR0810036, Quantify effects of power uncertainty on fuel assembly characteristics, within work package FT-15OR081003 ST Analysis-ORNL. This research was also supported by the Consortium for Advanced Simulation of Light Water Reactors (, an Energy Innovation Hub ( for Modeling and Simulation of Nuclear Reactors under U.S. Department of Energy Contract No. DE-AC05-00OR22725. The discharge rod internal pressure (RIP) and cladding hoop stress (CHS) distributions are quantified for Watts Bar Nuclear Unit 1 (WBN1) fuel rods by modeling core cycle design data, operation data (including modeling significant trips and downpowers), and as-built fuel enrichments and densities of each fuel rod in FRAPCON-3.5. A methodology is developed which tracks inter-cycle assembly movements and assembly batch fabrication information to build individual FRAPCON inputs for each evaluated WBN1 fuel rod. An alternate model for the amount of helium released from the zirconium diboride (ZrB2) integral fuel burnable absorber (IFBA) layer is derived and applied to FRAPCON output data to quantify the RIP and CHS for these types of fuel rods. SCALE/Polaris is used to quantify fuel rodspecific spectral quantities and the amount of gaseous fission products produced in the fuel for use in FRAPCON inputs. Fuel rods with ZrB2 IFBA layers (i.e., IFBA rods) are determined to have RIP predictions that are elevated when compared to fuel rod without IFBA layers (i.e., standard rods) despite the fact that IFBA rods often have reduced fill pressures and annular fuel pellets. The primary contributor to elevated RIP predictions at burnups less than and greater than 30 GWd

  5. A case of an infant with bundle branch reentrant ventricular tachycardia

    Directory of Open Access Journals (Sweden)

    Satoki Fujii


    Full Text Available Catheter ablation of the right bundle branch was performed on an 11-month-old infant for the treatment of drug-resistant bundle branch reentrant ventricular tachycardia. The occurrence of right bundle branch block could not be used as an endpoint of treatment because the patient had presented with incomplete right bundle branch block pattern during sinus rhythm. We performed ablation of the right bundle branch and utilized changes of duration and morphology of the QRS complex as indicators. Eight years have passed with no development of any atrioventricular block or tachycardia episode.

  6. Transport of single cells using an actin bundle-myosin bionanomotor transport system

    Energy Technology Data Exchange (ETDEWEB)

    Takatsuki, Hideyo; Rice, Kevin M; Kohama, Kazuhiro; Blough, Eric R [Department of Biological Sciences, Marshall University, Huntington, WV (United States); Tanaka, Hideyuki [Department of Molecular and Cellular Pharmacology, Gunma University Graduate School of Medicine, Maebashi (Japan); Kolli, Madhukar B; Nalabotu, Siva K [Center for Diagnostic Nanosystems, Marshall University, Huntington, WV (United States); Famouri, Parviz, E-mail: [Lane Department of Computer Science and Electrical Engineering, West Virginia University, Morgantown, WV (United States)


    The potential of using actin bundles for the transport of liposomes and single cells across myosin-coated surfaces is investigated. Compared to that observed with filamentous actin, the liposome transport using actin bundles was more linear in nature and able to occur over longer distances. Bundles, but not filamentous actin, were capable of moving single cells. Cargo unloading from bundles was achieved by incubation with Triton X-100. These data suggest that actin bundling may improve the ability of the myosin motor system for nanotransport applications.

  7. Horizontal gene transfer in human pathogens. (United States)

    Juhas, Mario


    Horizontal gene transfer has a tremendous impact on the genome plasticity, adaptation and evolution of bacteria. Horizontally transferred mobile genetic elements are involved in the dissemination of antibiotic resistance and virulence genes, thus contributing to the emergence of novel "superbugs". This review provides update on various mechanisms of horizontal gene transfer and examines how horizontal gene transfer contributes to the evolution of pathogenic bacteria. Special focus is paid to the role horizontal gene transfer plays in pathogenicity of the emerging human pathogens: hypervirulent Clostridium difficile and Escherichia coli (including the most recent haemolytic uraemic syndrome outbreak strain) and methicillin-resistant Staphylococcus aureus (MRSA), which have been associated with largest outbreaks of infection recently.

  8. Large eddy simulation of flow across in-line tube bundles

    Energy Technology Data Exchange (ETDEWEB)

    Sofiane Benhamadouche [Electricite de France R et D, MFTT, 6 quai Watier, 78400 Chatou (France); Dominique Laurence; Nicolas Jarrin [UMIST, MAME Dept, G. Begg Bldg, Sackville St. PO box 88, Manchester M601QD (United Kingdom); Electricite de France R et D, MFTT, 6 quai Watier, 78400 Chatou (France)


    Previously, Benhamadouche and Laurence (2003) produced very good results for the flow in a staggered tube bundle, using Large Eddy Simulation with EDF in-house finite volume code code-Saturne (Archambeau et al. (2004)). The discretization is based on a collocated arrangement for unstructured grids. A second order scheme in space and time is used with a standard Smagorinsky model. All the wall boundary cells are in the viscous layer, thus, no wall function is applied. The same numerical scheme is tested on a square in-line tube bundle with P/D = 1,44 and Re = 70000 (P is the vertical and horizontal tube spacing, D is the diameter of a tube and the Reynolds number is based on the gap velocity). The tube bundle is assumed infinite; periodic conditions are used in the three directions with an imposed flow rate. The dimensions of the computational domain have to be chosen (the computational cell, see figure 1 and the 3D elevation L{sub z}). Three computations are carried out (see table 1). Case 1 (1200000 cells) gives a non-symmetrical mean solution that impacts the tubes alternatively on the top and the bottom depending on the considered column (see figure 2). Case 2 gives the same behavior with fewer tubes. Case 3 gives a different solution in which the flow impacts the tubes on the same way whatever the column of the tubes (see figure 3). Note that the solution in also non-symmetrical in this case. A comparison of the total mean drag and lift coefficients and their rms values is given in table 2. The qualitative behavior is good for both cases; the rms value of the drag is between 30% to 50% lower than the rms value of the lift. However, Case 3 results are more realistic as the mean of the lift is almost zero and the other values are of the order of magnitude of the ones obtained for other tube bundles (P/D = 1,75 in Chen (1987)). One can conclude that the elevation in the third direction has a more important effect then the domain size and can impact seriously the

  9. Age-related decrease in rod bipolar cell density of the human retina ...

    Indian Academy of Sciences (India)

    During normal ageing, the rods (and other neurones) undergo a significant decrease in density in the human retina from the fourth decade of life onward. Since the rods synapse with the rod bipolar cells in the outer plexiform layer, a decline in rod density (mainly due to death) may ultimately cause an associated decline of ...

  10. 75 FR 21658 - Carbon and Certain Alloy Steel Wire Rod From Trinidad and Tobago (United States)


    ... Certain Alloy Steel Wire Rod From Trinidad and Tobago AGENCY: United States International Trade Commission... Investigation No. 731-TA-961 concerning carbon and certain alloy steel wire rod (``wire rod'') from Trinidad and... value. Caribbean Ispat Ltd., a Trinidadian producer and exporter of wire rod now known as Mittal Steel...

  11. Technical Development of Gamma Scanning for Irradiated Fuel Rod after Upgrade of System in Hot-cell

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Woo Seog; Kim, Hee Moon; Baik, Seung Je; Yoo, Byung Ok; Choo, Yong Sun


    Non-destructive test system was installed at hot-cell(M1) in IMEF(Irradiated Materials Examination Facility) more than 10 years ago for the diametric measurement and gamma scanning of fuel rod. But this system must be needed to be remodeled for the effective operations. In 2006, the system was upgraded for 3 months. The collimator bench can be movable with horizontal direction(x-direction) by motorized system for sectional gamma scanning and 3-dimensional tomography of fuel rod. So, gamma scanning for fuel rod can be detectable by x, y and rotation directions. It may be possible to obtain the radioactivities with radial and axial directions of pellet. This system is good for the series experiments with several positions. Operation of fuel bench and gamma detection program were linked each other by new program tools. It can control detection and bench moving automatically when gamma inspection of fuel rod is carried out with axial or radial positions. Some of electronic parts were added in PLC panel, and operating panel was re-designed for the remote control. To operate the fuel bench by computer, AD converter and some I/O cards were installed in computer. All of software were developed in Windows-XP system instead of DOS system. Control programs were made by visual-C language. After upgrade of system, DUPIC fuel which was irradiated in HANARO research reactor was detected by gamma scanning. The results were good and operation of gamma scanning showed reduced inspection time and easy control of data on series of detection with axial positions. With consideration of ECT(Eddy Current Test) installation, the computer program and hardware were set up as well. But ECT is not installed yet, so we have to check abnormal situation of program and hardware system. It is planned to install ECT in 2007.

  12. Characterization of control rod worths and fuel rod power peaking factors in the university of Utah TRIGA Mark I reactor

    Directory of Open Access Journals (Sweden)

    Alroumi Fawaz


    Full Text Available Control rod reactivity (worths for the three control rods and fuel rod power peaking factors in the University of Utah research reactor (100 kW TRIGA Mark I are characterized using the AGENT code system and the results described in this paper. These values are compared to the MCNP6 and existing experimental measurements. In addition, the eigenvalue, neutron spatial flux distributions and reaction rates are analyzed and discussed. The AGENT code system is widely benchmarked for various reactor types and complexities in their geometric arrangements of the assemblies and reactor core material distributions. Thus, it is used as a base methodology to evaluate neutronics variables of the research reactor at the University of Utah. With its much shorter computation time than MCNP6, AGENT provides agreement with the MCNP6 within a 0.5 % difference for the eigenvalue and a maximum difference of 10% in the power peaking factor values. Differential and integral control rod worths obtained by AGENT show well agreement with MCNP6 and the theoretical model. However, regulating the control rod worth is somewhat overestimated by both MCNP6 and AGENT models when compared to the experimental/theoretical values. In comparison to MCNP6, the total control rod worths and shutdown margin obtained with AGENT show better agreement to the experimental values.

  13. Anatomic Double-Bundle Anterior Cruciate Ligament Reconstruction Using In Situ Hamstring Graft With 4 Tunnels (United States)

    Wagih, Ahmad M.


    A careful review of the literature suggests that a significant number of patients undergoing anterior cruciate ligament (ACL) reconstruction have less-than-optimal results. Although overall outcomes of ACL reconstruction are favorable, there remains considerable room for improvement. Anatomically, the ACL consists of 2 major functional bundles, the anteromedial bundle and the posterolateral bundle. Biomechanically, both bundles contribute significantly to the anterior and rotational stability of the knee. Therefore anatomic double-bundle ACL reconstruction techniques may further improve the outcomes in ACL surgery. This article presents a technique for arthroscopic double-bundle ACL reconstruction that includes the use of 2 femoral and 2 tibial tunnels to restore both the anteromedial and posterolateral bundles of the ACL with minimal hardware for fixation. PMID:24749023

  14. A Multi-Stage Wear Model for Grid-to-Rod Fretting of Nuclear Fuel Rods

    Energy Technology Data Exchange (ETDEWEB)

    Blau, Peter Julian [ORNL


    The wear of fuel rod cladding against the supporting structures in the cores of pressurized water nuclear reactors (PWRs) is an important and potentially costly tribological issue. Grid-to-rod fretting (GTRF), as it is known, involves not only time-varying contact conditions, but also elevated temperatures, flowing hot water, aqueous tribo-corrosion, and the embrittling effects of neutron fluences. The multi-stage, closed-form analytical model described in this paper relies on published out-of-reactor wear and corrosion data and a set of simplifying assumptions to portray the conversion of frictional work into wear depth. The cladding material of interest is a zirconium-based alloy called Zircaloy-4, and the grid support is made of a harder and more wear-resistant material. Focus is on the wear of the cladding. The model involves an incubation stage, a surface oxide wear stage, and a base alloy wear stage. The wear coefficient, which is a measure of the efficiency of conversion of frictional work into wear damage, can change to reflect the evolving metallurgical condition of the alloy. Wear coefficients for Zircaloy-4 and for a polyphase zirconia layer were back-calculated for a range of times required to wear to a critical depth. Inputs for the model, like the friction coefficient, are taken from the tribology literature in lieu of in-reactor tribological data. Concepts of classical fretting were used as a basis, but are modified to enable the model to accommodate the complexities of the PWR environment. Factors like grid spring relaxation, pre-oxidation of the cladding, multiple oxide phases, gap formation, impact, and hydrogen embrittlement are part of the problem definition but uncertainties in their relative roles limits the ability to validate the model. Sample calculations of wear depth versus time in the cladding illustrate how GTRF wear might occur in a discontinuous fashion during months-long reactor operating cycles. A means to account for grid/rod gaps

  15. Cosmic multi-muon bundles measured at DELPHI

    CERN Document Server

    Travnicek, Petr


    The DELPHI detector at LEP, located 100 $m$ underground, has been used to detect the multi-muon bundles by cathode readout of its hadron calorimeter and its tracking detectors (TPC, muon chambers). The experimental apparatus allows us to study muon bundles originating from primary cosmic particles with energies in the interval $10^{14}$ - $10^{17} eV$. The cosmic events registered during the years 1999 and 2000 correspond roughly to $1.6 10^6 s$ of effective run time. The aim of the work is to compare the measured muon multiplicity distributions and predictions of high energy interaction models for different types of primary particles and also to determine the absolute flux of events in certain muon multiplicity range. The presentation describes the current status of the analysis.

  16. Catastrophic Failure and Critical Scaling Laws of Fiber Bundle Material

    Directory of Open Access Journals (Sweden)

    Shengwang Hao


    Full Text Available This paper presents a spring-fiber bundle model used to describe the failure process induced by energy release in heterogeneous materials. The conditions that induce catastrophic failure are determined by geometric conditions and energy equilibrium. It is revealed that the relative rates of deformation of, and damage to the fiber bundle with respect to the boundary controlling displacement ε0 exhibit universal power law behavior near the catastrophic point, with a critical exponent of −1/2. The proportion of the rate of response with respect to acceleration exhibits a linear relationship with increasing displacement in the vicinity of the catastrophic point. This allows for the prediction of catastrophic failure immediately prior to failure by extrapolating the trajectory of this relationship as it asymptotes to zero. Monte Carlo simulations are completed and these two critical scaling laws are confirmed.

  17. An improved partial bundle method for linearly constrained minimax problems

    Directory of Open Access Journals (Sweden)

    Chunming Tang


    Full Text Available In this paper, we propose an improved partial bundle method for solving linearly constrained minimax problems. In order to reduce the number of component function evaluations, we utilize a partial cutting-planes model to substitute for the traditional one. At each iteration, only one quadratic programming subproblem needs to be solved to obtain a new trial point. An improved descent test criterion is introduced to simplify the algorithm. The method produces a sequence of feasible trial points, and ensures that the objective function is monotonically decreasing on the sequence of stability centers. Global convergence of the algorithm is established. Moreover, we utilize the subgradient aggregation strategy to control the size of the bundle and therefore overcome the difficulty of computation and storage. Finally, some preliminary numerical results show that the proposed method is effective.

  18. Analyses of bundle experiment data using MATRA-h

    Energy Technology Data Exchange (ETDEWEB)

    Lim, In Cheol; Chea, Hee Taek [Korea Atomic Energy Research Institute, Taejon (Korea)


    When the construction and operation license for HANARO was renewed in 1995, 25% of CHF penalty was imposed. The reason for this was that the validation work related to the CHF design calculation was not enough for the assurance of CHF margin. As a part of the works to recover this CHF penalty, MATRA-h was developed by implementing the new correlations for the heat transfer, CHF prediction, subcooled void to the MATRA-a, which is the modified version of COBRA-IV-I done by KAERI. Using MATRA-h, the subchannel analyses for the bundle experiment data were performed. The comparison of the code predictions with the experimental results, it was found that the code would give the conservative predictions as far as the CHF in the bundle geometry is concerned. (author). 12 refs., 25 figs., 16 tabs.

  19. Through silicon vias filled with planarized carbon nanotube bundles. (United States)

    Wang, Teng; Jeppson, Kjell; Olofsson, Niklas; Campbell, Eleanor E B; Liu, Johan


    The feasibility of using carbon nanotube (CNT) bundles as the fillers of through silicon vias (TSVs) has been demonstrated. CNT bundles are synthesized directly inside TSVs by thermal chemical vapor deposition (TCVD). The growth of CNTs in vias is found to be highly dependent on the geometric dimensions and arrangement patterns of the vias at atmospheric pressure. The CNT-Si structure is planarized by a combined lapping and polishing process to achieve both a high removal rate and a fine surface finish. Electrical tests of the CNT TSVs have been performed and their electrical resistance was found to be in the few hundred ohms range. The reasons for the high electrical resistance have been discussed and possible methods to decrease the electrical resistance have been proposed.

  20. Buckling of a fiber bundle embedded in epoxy (United States)

    Hahn, H. T.; Sohi, M. M.


    Buckling of a fiber bundle embedded in epoxy resin was studied to gain insight into compressive failure mechanisms in unidirectional composites. The fibers used were E-glass, T300 graphite, T700 graphite, and P75 graphite. These fibers were combined with two different resins: Epon 815/V140 and Epon 828/Z. In both resins the failure mode of the bundle was found to be microbuckling of fibers for the first three types of fibers; however, the high-modulus P75 fibers failed in shear without any sign of microbuckling. The strains at which microbuckling occurred were higher than the compressive failure strains of the corresponding unidirectional composites. In the soft resin, Epon 815/V140, fibers buckled at lower strains than in the stiff resin, Epon 828/Z. The buckling strains and the segment lengths followed the trends predicted for a single filament embedded in an infinite matrix.

  1. Bundle adjustment with raw inertial observations in UAV applications (United States)

    Cucci, Davide Antonio; Rehak, Martin; Skaloud, Jan


    It is well known that accurate aerial position and attitude control is beneficial for image orientation in airborne photogrammetry. The aerial control is traditionally obtained by Kalman filtering/smoothing inertial and GNSS observations prior to the bundle-adjustment. However, in Micro Aerial Vehicles this process may result in poor attitude determination due to the limited quality of the inertial sensors, large alignment uncertainty and residual correlations between sensor biases and initial attitude. We propose to include the raw inertial observations directly into the bundle-adjustment instead of as position and attitude weighted observations from a separate inertial/GNSS fusion step. The necessary observation models are derived in detail within the context of the so called ;Dynamic Networks;. We examine different real world cases and we show that the proposed approach is superior to the established processing pipeline in challenging scenarios such as mapping in corridors and in areas where the reception of GNSS signals is denied.

  2. Balanced metrics for vector bundles and polarised manifolds

    DEFF Research Database (Denmark)

    Garcia Fernandez, Mario; Ross, Julius


    We consider a notion of balanced metrics for triples (X, L, E) which depend on a parameter α, where X is smooth complex manifold with an ample line bundle L and E is a holomorphic vector bundle over X. For generic choice of α, we prove that the limit of a convergent sequence of balanced metrics...... leads to a Hermitian-Einstein metric on E and a constant scalar curvature Kähler metric in c_1(L). For special values of α, limits of balanced metrics are solutions of a system of coupled equations relating a Hermitian-Einstein metric on E and a Kähler metric in c1(L). For this, we compute the top two...

  3. A note on the tangent bundle of G/P

    Indian Academy of Sciences (India)

    Introduction. Let G be a simple linear algebraic group defined over C. Fix a proper parabolic subgroup. G/P. In [1], a Kähler–Einstein metric on G/P was constructed. This implies that the tangent bundle T (G/P ) is polystable (the definition is recalled below). We show that. T (G/P ) is stable. Since T (G/P ) is polystable, ...

  4. Optimal bundling of transmembrane helices using sparse distance constraints


    Sale, Ken; Faulon, Jean-Loup; Genetha A. Gray; Schoeniger, Joseph S.; Young, Malin M.


    We present a two-step approach to modeling the transmembrane spanning helical bundles of integral membrane proteins using only sparse distance constraints, such as those derived from chemical cross-linking, dipolar EPR and FRET experiments. In Step 1, using an algorithm, we developed, the conformational space of membrane protein folds matching a set of distance constraints is explored to provide initial structures for local conformational searches. In Step 2, these structures refined against ...

  5. Higgs Bundles and Representations of Complex Hyperbolic Lattices


    Maubon, Julien


    International audience; This paper is an introduction to the Higgs bundle theory of Hitchin and Simpson and a survey of its applications to the study of representations of complex hyperbolic lattices into Lie groups of Hermitian type. Some material concerning representations of surface groups will be covered but we shall be mainly interested in higher dimensional lattices, in particular in the proof of the rigidity of maximal representations of such lattices. (Concerning the rigidity of maxim...

  6. Image processing for cameras with fiber bundle image relay. (United States)

    Olivas, Stephen J; Arianpour, Ashkan; Stamenov, Igor; Morrison, Rick; Stack, Ron A; Johnson, Adam R; Agurok, Ilya P; Ford, Joseph E


    Some high-performance imaging systems generate a curved focal surface and so are incompatible with focal plane arrays fabricated by conventional silicon processing. One example is a monocentric lens, which forms a wide field-of-view high-resolution spherical image with a radius equal to the focal length. Optical fiber bundles have been used to couple between this focal surface and planar image sensors. However, such fiber-coupled imaging systems suffer from artifacts due to image sampling and incoherent light transfer by the fiber bundle as well as resampling by the focal plane, resulting in a fixed obscuration pattern. Here, we describe digital image processing techniques to improve image quality in a compact 126° field-of-view, 30 megapixel panoramic imager, where a 12 mm focal length F/1.35 lens made of concentric glass surfaces forms a spherical image surface, which is fiber-coupled to six discrete CMOS focal planes. We characterize the locally space-variant system impulse response at various stages: monocentric lens image formation onto the 2.5 μm pitch fiber bundle, image transfer by the fiber bundle, and sensing by a 1.75 μm pitch backside illuminated color focal plane. We demonstrate methods to mitigate moiré artifacts and local obscuration, correct for sphere to plane mapping distortion and vignetting, and stitch together the image data from discrete sensors into a single panorama. We compare processed images from the prototype to those taken with a 10× larger commercial camera with comparable field-of-view and light collection.

  7. Bundle Data Approach at GES DISC Targeting Natural Hazards (United States)

    Shie, Chung-Lin; Shen, Suhung; Kempler, Steven J.


    Severe natural phenomena such as hurricane, volcano, blizzard, flood and drought have the potential to cause immeasurable property damages, great socioeconomic impact, and tragic loss of human life. From searching to assessing the Big, i.e., massive and heterogeneous scientific data (particularly, satellite and model products) in order to investigate those natural hazards, it has, however, become a daunting task for Earth scientists and applications researchers, especially during recent decades. The NASA Goddard Earth Sciences Data and Information Service Center (GES DISC) has served Big Earth science data, and the pertinent valuable information and services to the aforementioned users of diverse communities for years. In order to help and guide our users to online readily (i.e., with a minimum effort) acquire their requested data from our enormous resource at GES DISC for studying their targeted hazard event, we have thus initiated a Bundle Data approach in 2014, first targeting the hurricane event topic. We have recently worked on new topics such as volcano and blizzard. The bundle data of a specific hazard event is basically a sophisticated integrated data package consisting of a series of proper datasets containing a group of relevant (knowledge--based) data variables readily accessible to users via a system-prearranged table linking those data variables to the proper datasets (URLs). This online approach has been developed by utilizing a few existing data services such as Mirador as search engine; Giovanni for visualization; and OPeNDAP for data access, etc. The online Data Cookbook site at GES DISC is the current host for the bundle data. We are now also planning on developing an Automated Virtual Collection Framework that shall eventually accommodate the bundle data, as well as further improve our management in Big Data.

  8. Weak point property and sections of Picard bundles on a ...

    Indian Academy of Sciences (India)

    Introduction. Debarre had proved that the Jacobian J0(X0) of a smooth curve X0 satisfies the diagonal property (Corollary 2.2 of [6]) i.e., there is a vector bundle of rank equal to the dimension of J0(X0) over J0(X0) × J0(X0), having a section whose zero scheme is the diagonal of J0(X0) × J0(X0). In this note, we generalize ...

  9. Determinants of contractile forces generated in disorganized actomyosin bundles. (United States)

    Kim, Taeyoon


    Actomyosin machinery is a fundamental engine consisting mostly of actin filaments, molecular motors, and passive cross-linkers, generating mechanical forces required for biological processes of non-muscle cells such as cell migration, cytokinesis, and morphogenesis. Although the molecular and physical properties of key elements in the actomyosin machinery have been characterized well, it still remains unclear how macroscopic force buildup and dissipation in actomyosin networks and bundles depend on the microscopic properties of individual cytoskeletal components and their local interactions. To bridge such a gap between macroscopic and microscopic scales, we have developed a three-dimensional computational model of actomyosin bundles clamped to an elastic substrate with minimal components: actin filaments, passive cross-linkers, and active motors. Our model accounts for several key features neglected by previous studies despite their significance for force generation, such as realistic structure and kinetics of the motors. Using the model, we systematically investigated how net tension in actomyosin bundles is governed via interplay between motors and cross-linkers. We demonstrated motors can generate large tension on a bundle in the absence of cross-linkers in a very inefficient, unstable manner. Cross-linkers help motors to generate their maximum potential forces as well as enhance overall connectivity, leading to much higher efficiency and stability. We showed further that the cross-linkers behave as a molecular clutch with tunable friction which has quite distinct effects on net tension depending on their cross-linking angles. We also examined the source of symmetry breaking between tensile and compressive forces during tension generation process and discussed how the length and dynamics of actin filaments and the stiffness of the elastic substrate can affect the generated tension.


    Directory of Open Access Journals (Sweden)

    H. S. Gevorgyan


    Full Text Available Nerve-sparing radical prostatectomy is one of the high-tech operations in urology, and the challenge of the surgeon is not only to remove the prostate tumor, but also to provide a high quality of life. The fact that most questions devoted from patients in a conversation with the surgeon before the operation are devoted to this issue, shows the importance and relevance. At present, the diagnostic methods allow significantly more likely to detect early  prostate cancer, making finding and treatment of these patients more affordable and allows to apply this operation.Lately, it seems urgent to explore the possibility of water jet dissection in the field of urology, in particular, for nerve-sparing prostatectomy. Preservation of erectile function depends largely on the quality of separating the neurovascular bundle. Standard use of electrocautery is associated with damage to the neurovascular bundle.  When performing operations using water-jet mobilization of prostate the selective dissection of tissue is performed. This avoids injury of neurovascular bundle and further postoperative complications. The use of this technique may allow the surgeon to provide a more accurate mobilization prostate and selectively controlled intersection vessels heading to the prostate from the neurovascular bundle, reduce intraoperative blood loss,  maintaining continence, erectile function.This literature review is considered by the experience of using nerve-sparing radical prostatectomy using a water-jet dissector, estimated intraoperative parameters using this method.However, we have the lack of extensive research capabilities of this technique when performing nerve-preserving radical prostatectomy, that does not allow to make a comprehensive presentation on the benefits of this technique and its effects on erectile function and quality of urination, further study of this issue in such a difficult category of patients.

  11. Control Rod Driveline Reactivity Feedback Model for Liquid Metal Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Young-Min; Jeong, Hae-Yong; Chang, Won-Pyo; Cho, Chung-Ho; Lee, Yong-Bum


    The thermal expansion of the control rod drivelines (CRDL) is one important passive mitigator under all unprotected accident conditions in the metal and oxide cores. When the CRDL are washed by hot sodium in the coolant outlet plenum, the CRDL thermally expands and causes the control rods to be inserted further down into the active core region, providing a negative reactivity feedback. Since the control rods are attached to the top of the vessel head and the core attaches to the bottom of the reactor vessel (RV), the expansion of the vessel wall as it heats will either lower the core or raise the control rods supports. This contrary thermal expansion of the reactor vessel wall pulls the control rods out of the core somewhat, providing a positive reactivity feedback. However this is not a safety factor early in a transient because its time constant is relatively large. The total elongated length is calculated by subtracting the vessel expansion from the CRDL expansion to determine the net control rod expansion into the core. The system-wide safety analysis code SSC-K includes the CRDL/RV reactivity feedback model in which control rod and vessel expansions are calculated using single-nod temperatures for the vessel and CRDL masses. The KALIMER design has the upper internal structures (UIS) in which the CRDLs are positioned outside the structure where they are exposed to the mixed sodium temperature exiting the core. A new method to determine the CRDL expansion is suggested. Two dimensional hot pool thermal hydraulic model (HP2D) originally developed for the analysis of the stratification phenomena in the hot pool is utilized for a detailed heat transfer between the CRDL mass and the hot pool coolant. However, the reactor vessel wall temperature is still calculated by a simple lumped model.

  12. Strategy for Fuel Rod Receipt, Characterization, Sample Allocation for the Demonstration Sister Rods

    Energy Technology Data Exchange (ETDEWEB)

    Marschman, Steven C. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Warmann, Stephan A. [Portage, Inc., Idaho Falls, ID (United States); Rusch, Chris [NAC International, Inc., Norcross, GA (United States)


    , inert gas backfilling, and transfer to an Independent Spent Fuel Storage Installation (ISFSI) for multi-year storage. To document the initial condition of the used fuel prior to emplacement in a storage system, “sister ” fuel rods will be harvested and sent to a national laboratory for characterization and archival purposes. This report supports the demonstration by describing how sister rods will be shipped and received at a national laboratory, and recommending basic nondestructive and destructive analyses to assure the fuel rods are adequately characterized for UFDC work. For this report, a hub-and-spoke model is proposed, with one location serving as the hub for fuel rod receipt and characterization. In this model, fuel and/or clad would be sent to other locations when capabilities at the hub were inadequate or nonexistent. This model has been proposed to reduce DOE-NE’s obligation for waste cleanup and decontamination of equipment.

  13. Fluorescence Endoscopy in vivo based on Fiber-bundle Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Zufiria, B.; Gomez-Garcia, P.; Stamatakis, K.; Vaquero, J.J.; Fresno, M.; Desco, M.; Ripoll, J.; Arranz, A.


    High-resolution imaging techniques have become important for the determination of the cellular organization that is coupled to organ function. In many cases the organ can be viewed without the need of ionizing radiation techniques in an easier way. This is the case of the gastrointestinal tract, an organ that can be directly accessed with endoscopy avoiding any invasive procedure. Here we describe the design, assembly and testing of a fluorescence high-resolution endoscope intended for the study of the cellular organization of the colon in an experimental mouse model of colon carcinoma. Access to the colon of the mouse took place using a fiber-optic bundle that redirects the light coming from a LED to produce fluorescence and detect it back through the fiber bundle. Results from in vivo and ex-vivo test using our fluorescence fiber bundle endoscope show altered tissue structure and destruction of the intestinal crypts in tumor-bearing areas compared with healthy tissue. (Author)

  14. Differential geometry of moduli spaces of quiver bundles (United States)

    Biswas, Indranil; Schumacher, Georg


    Let P be a parabolic subgroup of a semisimple affine algebraic group G defined over C and X a compact Kähler manifold. L. Álvarez-Cónsul and O. García-Prada associated to these a quiver Q and representations of Q into holomorphic vector bundles on X (Álvarez-Cónsul and García-Prada, 2003) [1, 2]. Our aim here is to investigate the differential geometric properties of the moduli spaces of representations of Q into vector bundles on X. In particular, we construct a Hermitian form on these moduli spaces. A fiber integral formula is proved for this Hermitian form; this fiber integral formula implies that the Hermitian form is Kähler. We compute the curvature of this Kähler form. Under an assumption which says that X is a complex projective manifold, this Kähler form is realized as the curvature of a certain determinant line bundle equipped with a Quillen metric.

  15. Fabrication of CANFLEX bundle kit for irradiation test in NRU

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Moon Sung; Kwon, Hyuk Il; Ji, Chul Goo; Chang, Ho Il; Sim, Ki Seob; Suk, Ho Chun


    CANFLEX bundle kit was prepared at KAERI for the fabrication of complete bundle at AECL. Completed bundle will be used for irradiation test in NRU. Provisions in the `Quality Assurance Manual for HWR Fuel Projects,` `Manufacturing Plan` and `Quality Verification, Inspection and Test Plan` were implemented as appropriately for the preparation of CANFLEX kit. A set of CANFLEX kit consist of 43 fuel sheath of two different sizes with spacers, bearing pads and buttons attached, 2 pieces of end plates and 86 pieces of end caps with two different sizes. All the documents utilized as references for the fabrication such as drawings, specifications, operating instructions, QC instructions and supplier`s certificates are specified in this report. Especially, suppliers` certificates and inspection reports for the purchased material as well as KAERI`s inspection report are integrated as attachments to this report. Attached to this report are supplier`s certificates and KAERI inspection reports for the procured materials and KAERI QC inspection reports for tubes, pads, spacers, buttons, end caps, end plates and fuel sheath. (author). 37 refs.

  16. Compactifications of the Heterotic string with unitary bundles

    Energy Technology Data Exchange (ETDEWEB)

    Weigand, T.


    In this thesis we investigate a large new class of four-dimensional supersymmetric string vacua defined as compactifications of the E{sub 8} x E{sub 8} and the SO(32) heterotic string on smooth Calabi-Yau threefolds with unitary gauge bundles and heterotic five-branes. The first part of the thesis discusses the implementation of this idea into the E{sub 8} x E{sub 8} heterotic string. After specifying a large class of group theoretic embeddings featuring unitary bundles, we analyse the effective four-dimensional N=1 supergravity upon compactification. From the gauge invariant Kaehler potential for the moduli fields we derive a modification of the Fayet-Iliopoulos D-terms arising at one-loop in string perturbation theory. From this we conjecture a one-loop deformation of the Hermitian Yang-Mills equation and introduce the idea of {lambda}-stability as the perturbatively correct stability concept generalising the notion of Mumford stability valid at tree-level. We then proceed to a definition of SO(32) heterotic vacua with unitary gauge bundles in the presence of heterotic five-branes and find agreement of the resulting spectrum with the S-dual framework of Type I/Type IIB orientifolds. A similar analysis of the effective four-dimensional supergravity is performed. Further evidence for the proposed one-loop correction to the stability condition is found by identifying the heterotic corrections as the S-dual of the perturbative part of {pi}-stability as the correct stability concept in Type IIB theory. After reviewing the construction of holomorphic stable vector bundles on elliptically fibered Calabi-Yau manifolds via spectral covers, we provide semi-realistic examples for SO(32) heterotic vacua with Pati-Salam and MSSM-like gauge sectors. We finally discuss the construction of realistic vacua with flipped SU(5) GUT and MSSM gauge group within the E{sub 8} x E{sub 8} framework, based on the embedding of line bundles into both E{sub 8} factors. Some of the appealing

  17. Getting the Most from Your CD-ROM Dollars: The CD-ROM Bundle [and] The Pros and Cons of CD-ROM Bundling. (United States)

    Sarjeant, Eric W.; O'Connor, Mary Ann


    Discusses and reviews CD-ROM bundles--i.e., hardware, software and CD-ROM kits--including their features, specifications, drawbacks, and prices. Recommends buying through mail order for the best selection and price. The pros and cons of bundling as a marketing strategy are discussed and a list of vendors is provided. (EA)

  18. Plasmonic-cavity model for radiating nano-rod antennas

    DEFF Research Database (Denmark)

    Peng, Liang; Mortensen, N. Asger


    In this paper, we propose the analytical solution of nano-rod antennas utilizing a cylindrical harmonics expansion. By treating the metallic nano-rods as plasmonic cavities, we derive closed-form expressions for both the internal and the radiated fields, as well as the resonant condition and the ......In this paper, we propose the analytical solution of nano-rod antennas utilizing a cylindrical harmonics expansion. By treating the metallic nano-rods as plasmonic cavities, we derive closed-form expressions for both the internal and the radiated fields, as well as the resonant condition...... and the radiation efficiency. With our theoretical model, we show that besides the plasmonic resonances, efficient radiation takes advantage of (a) rendering a large value of the rods' radius and (b) a central-fed profile, through which the radiation efficiency can reach up to 70% and even higher in a wide...... frequency band. Our theoretical expressions and conclusions are general and pave the way for engineering and further optimization of optical antenna systems and their radiation patterns....

  19. On Cherenkov light production by irradiated nuclear fuel rods (United States)

    Branger, E.; Grape, S.; Jacobsson Svärd, S.; Jansson, P.; Andersson Sundén, E.


    Safeguards verification of irradiated nuclear fuel assemblies in wet storage is frequently done by measuring the Cherenkov light in the surrounding water produced due to radioactive decays of fission products in the fuel. This paper accounts for the physical processes behind the Cherenkov light production caused by a single fuel rod in wet storage, and simulations are presented that investigate to what extent various properties of the rod affect the Cherenkov light production. The results show that the fuel properties have a noticeable effect on the Cherenkov light production, and thus that the prediction models for Cherenkov light production which are used in the safeguards verifications could potentially be improved by considering these properties. It is concluded that the dominating source of the Cherenkov light is gamma-ray interactions with electrons in the surrounding water. Electrons created from beta decay may also exit the fuel and produce Cherenkov light, and e.g. Y-90 was identified as a possible contributor to significant levels of the measurable Cherenkov light in long-cooled fuel. The results also show that the cylindrical, elongated fuel rod geometry results in a non-isotropic Cherenkov light production, and the light component parallel to the rod's axis exhibits a dependence on gamma-ray energy that differs from the total intensity, which is of importance since the typical safeguards measurement situation observes the vertical light component. It is also concluded that the radial distributions of the radiation sources in a fuel rod will affect the Cherenkov light production.

  20. Control rod worth calculations using deterministic and stochastic methods

    Energy Technology Data Exchange (ETDEWEB)

    Varvayanni, M. [NCSR ' DEMOKRITOS' , PO Box 60228, 15310 Aghia Paraskevi (Greece); Savva, P., E-mail: melina@ipta.demokritos.g [NCSR ' DEMOKRITOS' , PO Box 60228, 15310 Aghia Paraskevi (Greece); Catsaros, N. [NCSR ' DEMOKRITOS' , PO Box 60228, 15310 Aghia Paraskevi (Greece)


    Knowledge of the efficiency of a control rod to absorb excess reactivity in a nuclear reactor, i.e. knowledge of its reactivity worth, is very important from many points of view. These include the analysis and the assessment of the shutdown margin of new core configurations (upgrade, conversion, refuelling, etc.) as well as several operational needs, such as calibration of the control rods, e.g. in case that reactivity insertion experiments are planned. The control rod worth can be assessed either experimentally or theoretically, mainly through the utilization of neutronic codes. In the present work two different theoretical approaches, i.e. a deterministic and a stochastic one are used for the estimation of the integral and the differential worth of two control rods utilized in the Greek Research Reactor (GRR-1). For the deterministic approach the neutronics code system SCALE (modules NITAWL/XSDRNPM) and CITATION is used, while the stochastic one is made using the Monte Carlo code TRIPOLI. Both approaches follow the procedure of reactivity insertion steps and their results are tested against measurements conducted in the reactor. The goal of this work is to examine the capability of a deterministic code system to reliably simulate the worth of a control rod, based also on comparisons with the detailed Monte Carlo simulation, while various options are tested with respect to the deterministic results' reliability.

  1. Nonlinear stiffness profiles of external fixators constructed with composite rods. (United States)

    Carlson, Kimberly R; Kraus, Karl H; Kowaleski, Michael P


    To determine if composite connecting rods confer nonlinear stiffness characteristics on unilateral and bilateral external skeletal fixators (ESF) in cranial-caudal bending and axial loading. Mechanical testing performed on models. Six models of 6-pin ESF constructs composed of birch dowels, a commercial ESF system, and composite connecting rods. Unilateral and bilateral ESF configurations were assembled using either specially designed composite titanium and silicone (composite group) or solid titanium (solid group) connecting rods. Mechanical testing was performed in axial loading and 4-point cranial-caudal bending. Stiffness was determined at a low and high-load range, and was considered increasing and nonlinear if the stiffness at high loads was greater than at low loads. The stiffness of the solid group was linear in all testing modes and configurations. Bilateral composite fixators had a nonlinear increasing stiffness in axial loading and cranial-caudal bending. Unilateral composite fixators had a nonlinear increasing stiffness in axial loading, but not cranial-caudal bending. Solid connecting rods conferred a higher stiffness in all testing modes and configurations. Composite connecting rods resulted in nonlinear increasing axial and bending stiffness in bilateral fixators, and in axial load in unilateral fixators. Conventional ESF can be constructed so that the stiffness increases as load increases. This provides the surgeon with additional options to control the local mechanical environment of a healing fracture, which may be used to enhance fracture healing.

  2. Quasi-static and dynamic response of viscoelastic helical rods (United States)

    Temel, Beytullah; Fırat Çalim, Faruk; Tütüncü, Naki


    In this study, the dynamic behaviour of cylindrical helical rods made of linear viscoelastic materials are investigated in the Laplace domain. The governing equations for naturally twisted and curved spatial rods obtained using the Timoshenko beam theory are rewritten for cylindrical helical rods. The curvature of the rod axis, effect of rotary inertia, and shear and axial deformations are considered in the formulation. The material of the rod is assumed to be homogeneous, isotropic and linear viscoelastic. In the viscoelastic material case, according to the correspondence principle, the material constants are replaced with their complex counterparts in the Laplace domain. Ordinary differential equations in scalar form obtained in the Laplace domain are solved numerically using the complementary functions method to calculate the dynamic stiffness matrix of the problem. In the solutions, the Kelvin model is employed. The solutions obtained are transformed to the real space using the Durbin's numerical inverse Laplace transform method. Numerical results for quasi-static and dynamic response of viscoelastic models are presented in the form of graphics.

  3. Fault pseudotachylyte: a coseismic lightning rod (United States)

    Ferre, E. C.; Conder, J. A.; MathanaSekaran, N.; Geissman, J. W.


    of melt during the formation of a pseudotachylite vein. The increase in melt temperature is the most important factor affecting electrical conductivity in the fault plane. When the melt temperature rises from 1300 to 2000K, its electrical conductivity increases about 80 times. This implies that once a continuous pseudotachylite sheet-like vein is formed during an earthquake, the vein has a much higher electrical conductivity than its host-rock. The dramatic increase in electrical conductivity along the pseudotachylite plane might be synchronous with the generation of the coseismic electrical current. Thus, regardless of its origin, any electrical current produced during an earthquake will travel along the pseudotachylite plane which acts as a lightning rod. The magnetization of a solid due to an electrical current results from Biot-Savart law which states that an electrical current generates a magnetic field. The solidification of the pseudotachylite vein does not happen at once but proceeds from the margin inwards as an electrical current may still pass through the conducting pseudotachylite. Therefore, the host-rock of the pseudotachylite vein or its solidified margin can be magnetized by a coseismic current.

  4. Analysis of Explanted Magnetically Controlled Growing Rods From Seven UK Spinal Centers. (United States)

    Joyce, Thomas J; Smith, Simon L; Rushton, Paul R P; Bowey, Andrew J; Gibson, Michael J


    Analysis of explanted MAGnetic Expansion Control (MAGEC) growing rods. To analyze explanted MAGEC rods used in management of early onset scoliosis and identify the mode of failure in such cases. Magnetically controlled growing rods are increasingly used as the option of choice for early onset scoliosis. However, being more complex than conventional growing rods they are perhaps more likely to succumb to multifarious failure modes. In addition, metallosis has been reported around failed MAGEC rods. Explanted MAGEC rods from seven UK spinal centers were obtained for independent analysis. Thirty-four MAGEC rods, from 18 children, explanted for reasons including failure of rod lengthening and maximum rod distraction reached, were cut open to allow internal components to be evaluated and assessed. Externally, all MAGEC rods showed localized marks, which were termed "growth marks" as they indicated growth of the rod in vivo, on the extending bar component. After cutting open, titanium wear debris was found inside all 34 (100%) MAGEC rods. Ninety-one percent (31/34) of MAGEC rods showed measurable wear of the extending bar, towards the magnet end. Substantial damage to the radial bearing was seen inside 74% (25/34) of MAGEC rods while O-ring seal failure was seen in 53% (18/34) of cases. In 44% (15/34) of MAGEC rods the drive pin was fractured but this was felt to be an effect of rod failure, not a cause. The combination of high volumes of titanium wear debris alongside O-ring seal damage likely accounts for the metallosis reported clinically around some MAGEC rods. Based on this explant data, a failure mechanism in MAGEC rods due to the natural off axis loading in the spine was proposed. This is the largest data set reporting a complete analysis of explanted MAGEC rods to date. 4.

  5. One stage revision single-bundle anterior cruciate ligament reconstruction with impacted morselized bone graft following a failed double-bundle reconstruction

    Directory of Open Access Journals (Sweden)

    Ho Jong Ra


    Full Text Available Although double-bundle anterior cruciate ligament (ACL reconstruction has theoretical benefits such as more accurate reproduction of ACL anatomy, it is technically more demanding surgery. This report describes the case of a one stage revision single-bundle ACL reconstruction after primary double-bundle ACL reconstruction. A professional dancer had an ACL previously reconstructed with a double-bundle technique, but the femoral tunnels were malpositioned resulting in residual laxity and rotational instability. The previous femoral tunnel positions were vertical and widened. The previous vertical tunnels were filled with impacted bone graft and a revision single-bundle ACL reconstruction was performed via the new femoral tunnel with a 2 O'clock position between the previous two tunnels. After 10 months of postoperative rehabilitation, the patient returned to professional dancing with sound bony union and without any residual instability.

  6. Double-bundle depiction of the anterior cruciate ligament at 3 Tesla

    Energy Technology Data Exchange (ETDEWEB)

    Adriaensen, M.E.A.P.M. [Atrium Medical Center Parkstad, Department of Radiology, Heerlen (Netherlands); Hogan, B. [Sports Surgery Clinic, Department of Radiology, Dublin (Ireland); Al-Bulushi, H.I.J. [Armed Forces Hospital, Department of Radiology, Muscat (Oman); Kavanagh, E.C. [Mater Misericordiae Hospital, Department of Radiology, Dublin (Ireland)


    Magnetic resonance imaging on 3 Tesla (3T MRI) with arthroscopic correlation has proven to adequately identify the anteromedial bundle (AMB) and posterolateral bundle (PLB) in cadaver knees. The purpose of this study was to describe the depiction of ACL bundle anatomy on 3T MRI in daily practice. In a retrospective cohort study, we included 50 consecutive patients who underwent standard 3T MRI of the knee and had an intact ACL. Two musculoskeletal radiologists independently reviewed all scans for depiction of ACL bundle anatomy using standardized forms. Descriptive statistics were used. Twenty-three right knees (46%) and 27 left knees (54%) were included in the study. Mean age of the patients was 35 years (range 12 to 68 years); 37 patients were male (74%). ACL bundle anatomy was best depicted in the axial plane in 44 knees (88%) and in the coronal plane in six knees (12%). Two bundles were seen in 47 knees (94%). The AMB was completely seen in 45 knees (90%). The PLB was completely seen in 40 knees (80%). Both bundles were completely seen in 37 knees (76%). The double-bundle anatomy of the ACL is visualized in 94% of patients on 3T MRI. Because of potentially associated clinical benefits, we advocate to report separately on the anteromedial bundle and posterolateral bundle in case of anterior cruciate ligament injury of the knee. (orig.)

  7. Modelling of fuel bundle deformation at high temperatures: requirements, models and steps for consideration

    Energy Technology Data Exchange (ETDEWEB)

    Xu, S.; Xu, Z.; Fan, H.; Nitheanandan, T. [Atomic Energy of Canada Limited, MIssissauga, Ontario (Canada)


    To model thermal mechanical bundle deformation behaviour under high temperature conditions, several factors need to be considered. These are the sources of loads, deformation mechanisms, interactions within bundle components, bundle and pressure tube (PT) interaction, and boundary constraints on the fuel bundles under in-reactor conditions. This paper describes the modelling of the following three processes: Bundle slumping due to high temperature creep-sag of individual elements and endplates; Differential element expansion and fuel element bowing; and, Bundle distortion under axial loads. To model these processes, a number of key mechanisms for bundle deformation must be considered, which include: 1) Interaction of fuel elements in a bundle with their neighbours, 2) Endplate deformation, 3) Fuel elements lateral deformation under various loads and mechanisms, 4) Interaction within a fuel element, 5) Material property change at high temperatures, 6) Transient response of a bundle, and 7) Bundle configuration change. This paper summarises the new models needed for the mechanistic modelling of the key mechanisms mentioned above and provides an example to show how an endplate plasticity model is developed with results. (author)

  8. Recompletion by horizontal drilling pays off

    Energy Technology Data Exchange (ETDEWEB)

    Holifield, R.H.; Rehm, B.


    More than 20 wells have been recompleted in the Giddings field by drilling a new, horizontal interval from existing 5 1/2-in. cased wells for distances of 300 to 1,250 ft. Recompleting existing wells is much cheaper than drilling a new well. Plus, the new completions, overall, produce better. The horizontal wells are routinely profitable now, and pay out occurs in 3 to 24 months. During this program, the techniques for slim-hole- medium-radius, horizontal drilling in Giddings have been mastered and costs have dropped 75%. It is believed that this program may be the first (or among the first) continuing horizontal project drilled out of cased wells with repeatable profitability as opposed to projected viability.

  9. Productivity and injectivity of horizontal wells

    Energy Technology Data Exchange (ETDEWEB)

    Aziz, Khalid


    One of the key issues addressed was pressure drop in long horizontal wells and its influence on well performance. Very little information is available in the literature on flow in pipes with influx through pipe walls. Virtually all of this work has been in small diameter pipes and with single-phase flow. In order to address this problem new experimental data on flow in horizontal and near horizontal wells have been obtained. Experiments were conducted at an industrial facility on typical 6 1/8 ID, 100 feet long horizontal well model. The new data along with available information in the literature have been used to develop new correlations and mechanistic models. Thus it is now possible to predict, within reasonable accuracy, the effect of influx through the well on pressure drop in the well.

  10. Horizontal Compilations of Nuclear Data III (United States)

    Soroko, Z. N.; Sukhoruchkin, S. I.; Sukhoruchkin, D. S.


    Compilations of resonance parameters for all nuclei (horizontal-type compilations) derived from study of reactions with neutrons and charge particles are described. Systematic trends in experimental data due to the differences in energy scales of spectrometers were found after comparison of data for many nuclei. The combination of data from horizontal-type compilations with data from the well-known file ENSDF expands the usefulness of these data files.

  11. Horizontal Brand Extension and Customer perception


    Khan, Khalid; Janthimapornkij, Rattanawilai


    Company use different method for extended their business to different market and to different segment. They use different method; brand extension is one of popular strategy for extension of business. Brand extension does not become successful for every brand, it is very risky. The purpose of this thesis is to study horizontal brand extension and customer perception. We will discuss horizontal brand extension and its two main types franchise brand extension and line extension. Brand extension ...

  12. Preparation of nanometer-scale rod array of hydroxyapatite crystal. (United States)

    Hayakawa, Satoshi; Li, Yaqi; Tsuru, Kanji; Osaka, Akiyoshi; Fujii, Eiji; Kawabata, Koji


    Fabrication of nano- or micro-structured scaffolds to mimic structural and three-dimensional details of natural bone or teeth has been the subject of much interest, and this study proposes a new strategy for self-assembling one-dimensional hydroxyapatite (HAp) nanorods into organized superstructures. A nanometer-scale rod array of HAp having preferred orientation to the c-axis was successfully prepared simply by soaking calcium-containing silicate glass substrates in Na(2)HPO(4) aqueous solution at 80 degrees C for various periods. Those HAp rods grew perpendicularly to the glass surface, and the crystallites covered the glass surface uniformly, resulting in a "dental enamel-like" rod array structure consisting of "pine-leaf-like" structure units.

  13. Simulations of optical sensors fabricated from metallic rods couplers

    Energy Technology Data Exchange (ETDEWEB)

    Singh, M. R. [Department of Physics and Astronomy, Western University Ontario, London, Ontario N6A 3K7 (Canada); Balakrishanan, Shankar [Department of Physics and Astronomy, Western University Ontario, London, Ontario, Canada, N6A 3K7 and Lawson Health Research Institute, 268, Grosvenor Street, London, Ontario N6A 4V2 (Canada)


    We have developed the optical sensing mechanism of photonic couplers fabricated from the periodically arranged metallic rods. The metallic rod lattice is embedded between two dielectric material waveguides. This structure is called metallic coupler. Using the transfer matrix method, expressions for the reflection and transmission coefficients of electromagnetic wave propagating in waveguides have been obtained. We found that for certain energies, the electromagnetic wave is totally reflected from the coupler. Similarly, for a certain energy range the light is totally transmitted. It has also been found that by changing the periodicity of the metallic rods, the transmitted energy can be reflected. The periodicity of the metallic lattice can be modified by applying an external stress or pressure. In other words, the system can be used as stress and pressure sensors. The present findings can be used to make new types photonic sensors.

  14. 3-D rod ejection analysis using a conservative methodology

    Energy Technology Data Exchange (ETDEWEB)

    Park, Min Ho; Park, Jin Woo; Park, Guen Tae; Um, Kil Sup; Ryu, Seok Hee; Lee, Jae Il; Choi, Tong Soo [KEPCO, Daejeon (Korea, Republic of)


    The point kinetics model which simplifies the core phenomena and physical specifications is used for the conventional rod ejection accident analysis. The point kinetics model is convenient to assume conservative core parameters but this simplification loses large amount of safety margin. The CHASER system couples the three-dimensional core neutron kinetics code ASTRA, the sub-channel analysis code THALES and the fuel performance analysis code FROST. The validation study for the CHASER system is addressed using the NEACRP three-dimensional PWR core transient benchmark problem. A series of conservative rod ejection analyses for the APR1400 type plant is performed for both hot full power (HFP) and hot zero power (HZP) conditions to determine the most limiting cases. The conservative rod ejection analysis methodology is designed to properly consider important phenomena and physical parameters.

  15. Characterisation of Plasma Filled Rod Pinch electron beam diode operation (United States)

    MacDonald, James; Bland, Simon; Chittenden, Jeremy


    The plasma filled rod pinch diode (aka PFRP) offers a small radiographic spot size and a high brightness source. It operates in a very similar to plasma opening switches and dense plasma focus devices - with a plasma prefill, supplied via a number of simple coaxial plasma guns, being snowploughed along a thin rod cathode, before detaching at the end. The aim of this study is to model the PFRP and understand the factors that affect its performance, potentially improving future output. Given the dependence on the PFRP on the prefill, we are making detailed measurements of the density (1015-1018 cm-3), velocity, ionisation and temperature of the plasma emitted from a plasma gun/set of plasma guns. This will then be used to provide initial conditions to the Gorgon 3D MHD code, and the dynamics of the entire rod pinch process studied.

  16. The ATLAS liquid argon calorimeters Read Out Driver (ROD) system

    CERN Document Server

    Henry-Coüannier, F


    The electronic Readout chain for the Liquid Argon calorimeters of the ATLAS detector is briefly presented. Special attention is given to the Read Out Drivers (ROD) which will receive the triggered data from approximately 200,000 calorimeter cells at a 100 kHz event rate. In the ROD boards the energy will be computed for each cell from discrete samples of the waveform using optimal filtering algorithms running in fast digital signal processors. The monitoring of the calorimeter data will also be performed at the ROD level. Performances expected in ATLAS which have been evaluated from simulation studies are presented. A demonstrator system currently under construction is described and performances of the Processing Units (DSP daughter boards) are presented. 4 Refs.

  17. PACTEL: Experiments on the behaviour of the new horizontal steam generator

    Energy Technology Data Exchange (ETDEWEB)

    Kouhia, J.; Riikonen, V.; Purhonen, H. [VTT Energy, Lappeenranta (Finland)


    Experiments were performed to study the behaviour of the PACTEL facility, a medium scale integral test loop simulating VVER 440 pressurized water reactors. The study focused on the operation of the new horizontal steam generator model installed in PACTEL. Three experiments were conducted: a small-break test to observe the steam generator behaviour over a range of primary coolant inventories, a hot leg loop seal experiment to study the cyclic behaviour of a loop seal and a loss of secondary side feedwater test to examine the effect of uncovered tubes in the steam generator. A reverse flow was observed in the lower part of the U-tube bundle of the steam generator during natural circulation. The flow reversal point dropped when the tubes uncovered, during secondary inventory reduction. (orig.). 5 refs.

  18. Do infants have the horizontal bias? (United States)

    Van Renswoude, D R; Johnson, S P; Raijmakers, M E J; Visser, I


    A robust set of studies show that adults make more horizontal than vertical and oblique saccades, while scanning real-world scenes. In this paper we study the horizontal bias in infants. The directions of eye movements were calculated for 41 infants (M=8.40 months, SD=3.74, range=3.48-15.47) and 47 adults (M=21.74 years, SD=4.54, range=17.89-39.84) while viewing 28 real-world scenes. Saccade directions were binned to study the proportion of saccades in the horizontal, vertical and oblique directions. In addition, saccade directions were also modeled using a mixture of Von Mises distributions, to account for the relatively large amount of variance in infants data. Horizontal bias was replicated in adults and also found in infants, using both the binning and Von Mises approach. Moreover, a developmental pattern was observed in which older infants are more precise in targeting their saccades than younger infants. That infants have a horizontal bias is important in understanding infants' eye movements. Future studies should account for the horizontal bias in their designs and analyses. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. Experimental verification of the horizontal steam generator boil-off transfer degradation at natural circulation

    Energy Technology Data Exchange (ETDEWEB)

    Hyvaerinen, J. [Finnish Centre for Radiation and Nuclear Safety, Helsinki (Finland); Kouhia, J. [VTT Energy, Lappeenranta (Finland)


    The presentation summarises the highlights of experimental results obtained for VVER type horizontal steam generator heat transfer, primary side flow pattern, and mixing in the hot collector during secondary side boil-off with primary at single-phase natural circulation. The experiments were performed using the PACTEL facility with Large Diameter (LD) steam generator models, with collector instrumentation designed specifically for these tests. The key findings are as follows: (1) the primary to secondary heat transfer degrades as the secondary water inventory is depleted, following closely the wetted tube area; (2) a circulatory flow pattern exists in the tube bundle, resulting in reversed flow (from cold to the hot collector) in the lower part of the tube bundle, and continuous flow through the upper part, including the tubes that have already dried out; and (3) mixing of the hot leg flow entering the hot collector and reversed, cold, tube flow remains confined within the collector itself, extending only a row or two above the elevation at which tube flow reversal has taken place. 6 refs.

  20. An experimental study on mechanical properties of GFRP braid-pultruded composite rods

    Directory of Open Access Journals (Sweden)


    Full Text Available In this work, a conventional textile braiding machine was modified and added to a pultrusion line in order to produce glass fiber reinforced composite rods by braiding-pultrusion technique. Braid-pultruded (BP rods were produced with three braid roving linear densities and also with three different braid angles. To study the influence of overbraiding on mechanical properties of pultruded rods, unidirectional (UD rods, without braided fabric, were produced, as well. All rod types were subjected to tensile, bending and torsion tests. The experimental results showed that BP rods have considerably higher shear modulus, but lower tensile modulus and flexural rigidity than those of UD pultruded rods, when fiber volume fraction is kept constant. Moreover, rods produced with higher braid roving linear densities had better torsional, but lower tensile and flexural properties. The highest shear modulus was observed in BP rods with braid angle of 45°.