WorldWideScience

Sample records for hokokusho nenryo denchi

  1. Fiscal 1991 report. International Fuel Cell Conference; Nenryo denchi kokusai symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Lectures, presentations, and questions given at the event involved items 1) Plenary session, 2) Technology development strategies, 3) Phosphoric acid fuel cell (PAFC), 4) Molten carbonate fuel cell (MCFC), 5) Solid oxide fuel cell (SOFC), 6) Other fuel cells, and item 7) Closing session. Under item 1), current states and prospects of technological development were reported by Agency of Industrial Science and Technology of Japan and by industrial technology developing organizations of the U.S. and Europe. Under item 2), a report was given by the U.S. about a fuel cell-driven automobile developing program. Under item 3), a report was given on the exchange of information about plant operation, maintenance, and inspection with importance attached to accuracy. Under item 4), reports were given about a 70kW stack operating program of the U.S. and a 1MW stack pilot plant program of Japan. Under item 5), some NEDO (New Energy and Industrial Technology Development Organization) projects and a 25kW stack operating test of Westinghouse Electric Corporation were reported. What were learned through participation in this conference are mentioned below. Japan is in the forefront as far as the development of PAFC and MCFC technologies are concerned. The U.S. is ahead of Japan in the development of SOFC while also in Japan efforts to develop element technologies for SOFC are in progress steadily. The U.S. and European countries lead Japan in the development of the polymer electrolyte fuel cell (PEFC). (NEDO)

  2. Achievement report on research and development in the Sunshine Project in fiscal 1979. Research on fuel cells (Research on aqueous alkaline solution electrolyte fuel cells); 1979 nendo nenryo denchi no kenkyu seika hokokusho. Arukari suiyoeki denkaishitsu nenryo denchi no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    This paper describes achievements in fiscal 1979 in research on aqueous alkaline solution electrolyte fuel cells. Trial fabrication and tests for an oxygen electrode were performed on a catalytic electrode added with silver using carbonblack and graphites as carriers having excellent corrosion resistance and large surface area. Characteristics not inferior to electrodes using activated carbon as a carrier were obtained in both of the initial characteristics and continuous discharge characteristics. A platinum added electrode also showed the same performance as the silver added electrode. A hydrogen electrode containing Zr and iron among those containing Raney-Ni was found to have high oxidation resistance and stability in terms of life. A platinum added electrode using graphite as a carrier provided satisfactory initial characteristics as a hydrogen electrode. Research on a single cell construction has used and tested eight-cell laminated cells with an area of 1,000 cm{sup 2} using bipolar sheets made of carbon. The test verified appropriate the removal of produced water and heat using mainly the hydrogen circulation, which has been discussed in the summary design. The paper describes heat cycles, for which tests of ten and odds times in total were performed to have demonstrated that they are free of any anomaly. Furthermore, a manifold was attached as a means to improve the volume efficiency. Its function was also tested. (NEDO)

  3. FY 1993 report on the results of the commissioned research and development project. R and D of SOFC (solid oxide fuel cells); 1983 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    The research and development project is carried out for fuel cell power generation technologies and solid electrolyte type fuel cells, and the reports on the FY 1993 results issued by the participant organizations are summarized. For R and D of the modules, Fuji Electric conducted the R and D for the large-area, cell-stacked type, and Sanyo Electric for the composite cell-stacked type. For R and D of the materials and fundamental technologies, Fine Ceramics Center conducted the R and D for microscopic structures of the electrode, Fujikura for electrode structures produced by spraying or the like, Mitsubishi Heavy Industries for multi-functional fuel electrodes, Murata Seisakusho for co-sintering technologies, and Mitsui Shipbuilding for current collecting technologies. For R and D of the systems, Central Research Institute of Electric Power Industry conducted the R and D for the systems, Electric Power Development and Mitsubishi Heavy Industries jointly for designs of the cell peripheries, and the Japan Research and Development Center for Metals for elementary technologies for the peripheral devices. (NEDO)

  4. FY 1992 report on the results of the commissioned research and development project. R and D of SOFC (solid oxide fuel cells); 1992 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-05-01

    The research and development project is carried out for fuel cell power generation technologies and solid electrolyte type fuel cells, and the reports on the FY 1992 results issued by the participant organizations are summarized. For R and D of the modules, Fuji Electric conducted the R and D for the large-area, cell-stacked type, and Sanyo Electric for the composite cell-stacked type. For R and D of the materials and fundamental technologies, Fine Ceramics Center is conducted the R and D for microscopic structures of the electrode, Fujikura for electrode structures produced by spraying or the like, Mitsubishi Heavy Industries for multi-functional fuel electrodes, Murata Seisakusho for co-sintering technologies, and Mitsui Shipbuilding for current collecting technologies. For R and D of the systems, Central Research Institute of Electric Power Industry conducted the R and D for the systems, Electric Power Development and Mitsubishi Heavy Industries jointly for designs of the cell peripheries, and the Japan Research and Development Center for Metals for elementary technologies for the peripheral devices. (NEDO)

  5. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. Standardization of FCEVs; 2000 nendo nenryo denchi fukyu kiban seibi jigyo jidoshayo nenryo denchi fukyu kiban seibi seika hokokusho. FCEV hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the FY 2000 activities for standardization of fuel cell powered vehicles and development of the infrastructures related to participation in ISO. Fuel cell powdered vehicles are believed to be the most favored vehicles of the next generation for their low emissions and fuel efficiency. The world leading automakers, including Japanese makers, have announced plans to commercialize these vehicles in 2003 to 2004. Under these situations, the discussion has been initiated to move forward standardization of the fuel cell powdered vehicles at the international conferences, e.g., ISO (International Standardization Organization) and IEC (International Electrotechnical Commission). At ISO/TC22/SC21 (Electric Vehicles) for which the Japan Electric Vehicle Association (JEVA) is in charge as the domestic council, the proposal has been made and approved to begin working towards the standardization at the conference in November 1999. Consequently, FCEV special subcommittee consisting of public organizations (including academic organizations and Ministry of Economy, Trade and Industry), automakers, automotive parts manufacturers and other organizations related to the automotive industry has been established in February 2000 under the JEVA standardization section and started the activities. The Japanese proposals for safety and fuel cell vehicle terminology will be presented to the ISO meetings to be held in May 2001 in Tokyo. (NEDO)

  6. Achievement report on research and development in the Sunshine Project in fiscal 1980. Research on fuel cells (Research on aqueous alkaline solution electrolyte fuel cells); 1980 nendo nenryo denchi no kenkyu seika hokokusho. Arukari suiyoeki denkaishitsu nenryo denchi no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This paper describes the achievements in fiscal 1980 in the Sunshine Project on developing aqueous alkaline solution electrolyte fuel cells. The oxygen electrode is a silver catalyst electrode using as carriers carbon lack and graphite powders having good corrosion resistance. A continuous discharge test was performed on the electrode for 3,000 hours. Furnace black having large surface area and naturally colloidal graphite showed stable performance. The hydrogen electrode, which is a catalyst electrode made of Raney-Ni containing third elements was given a 3000-hour continuous discharge test, where Zr addition presented stable performance. Activated carbon was found a good carrier in platinum added electrodes. For electrodes operating under high pressure gases, electrodes attached with sintered nickel film are suitable. With regard to prototype cells, laminated cells with high volume efficiency structured mainly with gasket seals were designed and fabricated. The IV characteristics measurement and continuous discharge test thereon revealed no functional problems. Furthermore, cells having electrode area of 100 cm{sup 2} and using bipolar sheets made of carbon were verified capable of withstanding 2000-hour continuous discharge. A non-conductive resin mold was proposed to prevent electrolytic corrosion of the carbon sheets. Discussions were given also on corrosion resistance of bonding agents. (NEDO)

  7. Survey report for fiscal 1998. Achievement report on research and development of direct methanol fuel cell; 1998 nendo direct methanol nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    Research and development has been performed on a direct methanol fuel cell (DMFC) to generate electric power through direct chemical reaction of methanol not being given modification as a fuel cell to be used for automotive engines. This paper summarizes the achievements in fiscal 1998. In the research of the membranes to conduct ions for the DMFC, an ion conduction membrane which introduces POSS group as the methanol eliminating functional group was prepared to achieve enhancement in tensile strength, heat resistance, and ion conductivity. In the power generation characteristics of the DMFC, verification was given on power generation performance with as high main power density as 0.1 W/cm{sup 2} by using the available electrolytic membranes and electrode catalysts. The characteristics showed effectiveness of the DMFC as the electric power supply source. In addition, fundamental findings were obtained on factors affecting the power generation characteristics of the DMFC as a result of generating power under different conditions. Research and development was given also on the water-methanol-ion exchange polymeric membrane, ion exchange membranes provided with lipophilic and water repellent electrolyte, solid polymeric membranes having high proton conductivity and low methanol permeability, and a new micro-porous filling type polymeric membrane. (NEDO)

  8. FY 2000 report on the results of the R and D of solid oxide fuel cells (SOFC); 2000 nendo kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    Development of fuel cell power generation technology and R and D of solid oxide fuel cells were carried out, and reports of the FY 2000 results of companies were summed up. As to the R and D of the cell module, the R and D on the wet type cylinder module were made jointly by Toto Ltd., Kyushu Electric Power Co. and Nippon Steel Corp. As to the R and D of materials/basic technology, the following were conducted: evaluation of reliability of the cell module (evaluation of thermal cycle characteristics, etc.) by Chubu Electric Power Co., evaluation of reliability of the cell module (cell characteristics/stress evaluation) by Tokyo Gas Co. Ltd., cost reduction of cell materials (evaluation of chemical characteristics) by Central Research Institute of Electric Power Industry, and cost reduction of cell materials (evaluation of mechanical/thermal characteristics) by Japan Fine Ceramics Center. Concerning the system study, study of the system (adaptation fields of the small system and the optimization) was conducted by Nippon Steel Corp. (NEDO)

  9. Achievement report for fiscal 1997 on research and development of solid electrolyte fuel cells; Kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu 1997 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    This paper describes the achievements in fiscal 1997 on research and development of solid electrolyte fuel cells. Fuji Electric has demonstrated possibilities of film type cells of predominantly metallic flat plate supporting type of a large-area cell lamination system, and seal-less stack structure. Sanyo Electric has discussed making thinner the composite cell lamination type anode, optimization in sintering temperature, and sealing materials. The Fine Ceramic Center has performed a 1,000-hour test on an La(Sr) MnO{sub 3}-YSZ electrode, in which A-site defect amount was decreased to 0.1-0.02 to stabilize micro-structure air electrodes for an extended period of time. Fujikura has discussed functional materials for high dispersion and slanting in a fuel electrode Ni/YSZ. Mitsubishi Heavy Industries has fabricated MgO-based fuel electrodes on a trial basis, and performed internal reformation and power generation tests by using full-size stacks. Murata Manufacturing Company has verified long-term power generation properties and stability of a three-layered co-sintered film of flat plate type. Mitsui Shipbuilding has reached a near final conclusion on the basic structure of gas separator cells. The Central Electric Power Research Institute has completed a conceptual design on a 300-MW class composite power generation system in which SOFC and gas turbines are combined. The Electric Power Development Company has discussed problems in SOFC composite power generation development using coal gasified fuel. (NEDO)

  10. Fiscal 1994 survey report. Survey of factors causing degradation of phosphoric acid fuel cells; 1994 nendo rinsangata nenryo denchi no cell rekka yoin chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This survey aims to effectively promote studies for evaluating phosphoric acid fuel cell degradation. Data of time-dependent changes in voltage are collected from 58 plants now in operation (for 17,500 hours at the maximum). Half of them exhibit a degradation rate of 0.25-1%/1000 hours while degradation is abruptly accelerated midway in the other half. Causes for voltage drop are not known clearly. Since but a little systematically collected test data are available concerning the mechanism of cell degradation, it is decided that tests be conducted using small test model cells sharing the same specifications. Primary test conditions (combination of temperature, current, and pressure with test reference levels), performance evaluating methods (conditions of data collection), and methods of investigation by dismantling (items and frequency of investigations) are determined, and guidelines are provided for element tests for complementing the said test items and for studying their relations with the degradation mechanism. Based on acceleration-related factors to be obtained by common specification test cells, corporations involved will develop their own accelerated test methods. Small cells are fabricated for testing parameters, and model cells are specified. (NEDO)

  11. FY 1999 report on the survey of the trend of the technology development of fuel cell vehicles; 1999 nendo chosa hokokusho. Nenryo denchi jidosha gijutsu kaihatsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    For the contribution to the introduction/spread of fuel cell vehicles, survey was conducted of the trend of technology development of fuel cell vehicles and the related infrastructure, the situation of the regulation/criteria, etc. As a typical project on the D and R of fuel cell vehicles in the U.S., cited is 'Partnership for a New Generation of Vehicles (PNGV)' which was commenced mainly by the US government and three US automobile manufacturers. The US DOE determined the introduction of a gasoline reforming type and has completed some prototype systems. In Europe, cited are 'Munich Airport Hydrogen Project,' Daimler-Chrysler's 'Transport Energy Strategy,' etc. In Japan, the introduction/promotion are being discussed in 'The New Sunshine Project' and 'The Millennium Project' proposed by former prime minister Obuchi. As to fuel cell vehicles, there are still many uncertain elements in performance, safety, economical efficiency, etc. Accordingly, the continued efforts should be made for the technology development for improvement of power performance, safety and economical efficiency and for the environmental arrangement of the infrastructure, introduction supporting system, etc. (NEDO)

  12. FY 1999 report on the survey of the trend of the technology development of fuel cell vehicles; 1999 nendo chosa hokokusho. Nenryo denchi jidosha gijutsu kaihatsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    For the contribution to the introduction/spread of fuel cell vehicles, survey was conducted of the trend of technology development of fuel cell vehicles and the related infrastructure, the situation of the regulation/criteria, etc. As a typical project on the D and R of fuel cell vehicles in the U.S., cited is 'Partnership for a New Generation of Vehicles (PNGV)' which was commenced mainly by the US government and three US automobile manufacturers. The US DOE determined the introduction of a gasoline reforming type and has completed some prototype systems. In Europe, cited are 'Munich Airport Hydrogen Project,' Daimler-Chrysler's 'Transport Energy Strategy,' etc. In Japan, the introduction/promotion are being discussed in 'The New Sunshine Project' and 'The Millennium Project' proposed by former prime minister Obuchi. As to fuel cell vehicles, there are still many uncertain elements in performance, safety, economical efficiency, etc. Accordingly, the continued efforts should be made for the technology development for improvement of power performance, safety and economical efficiency and for the environmental arrangement of the infrastructure, introduction supporting system, etc. (NEDO)

  13. Achievement report for 1st phase (fiscal 1974-80) Sunshine Program research and development - Hydrogen energy. Research on fuel cell (Research on high-temperature solid electrolyte fuel cell); 1974-1980 nendo suiso energy seika hokokusho. Nenryo denchi no kenkyu (koon kotai denkaishitsu nenryo denchi no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Relative to the research and development of technologies for fabricating, and assessing, materials for the constitution of high-temperature solid electrolyte fuel cells, stabilized zirconia solid electrolyte fuel cell manufacturing technologies are developed by use of thin film formation techniques such as high-frequency sputtering, plasma CVD (chemical vapor deposition), and the thermolysis of organic zirconia compound coating. As the result, it is found that high-frequency sputtering produces thin film which is satisfying in terms of cost efficiency. Furthermore, it is found that defects in solid electrolytic thin film formed by the high-frequency sputtering method, that is, pinholes and cracks, will be remedied when the coating thermolysis method is jointly applied. In the research on fuel cell power systems, column-type high-temperature solid electrolyte fuel cells are built, and a power generation test is conducted. The test is successfully completed when the output of a fuel cell of the 9-column module structure gradually increases until a maximum output of 110W is achieved. (NEDO)

  14. Report on achievement in developing fuel cell power generation technology in fiscal 1998. Research and development of molten carbonate fuel cell power generation system (Test of the research result report); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (kenkyu seika no honbun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper summarizes the text of the research result report in the separate volume II-1 from among the fiscal 1998 report on the achievement made on researching and developing a molten carbonate fuel cell (MCFC) power generation system. For the AC-DC type system whose high performance and large capacity stacks are being developed, detail designs were made on 250-kW class stack module assembly and installation procedure. At the same time, processing and forming were continued on such main components as electrodes, electrolyte plates and separators. The cells were assembled as modules, sintered, installed and adjusted. Aids were given by the process and control (PAC) test on devices and piping of the fuel cell system block. Cell life extension is also under study. For the parallel flow type stack, two 250-kW stacks were fabricated, and an overall adjustment test was begun thereon in March. For the reformer, an internal reforming system was developed for the 200-kW class system, whose adjustment test is scheduled for April 1999. Capacity increase is also under discussion. For practical use of MCFC, stack life of 40,000 hours is said required. The current status is at the level of exceeding 10,000 hours, but the necessity is seen in suppressing voltage drop associated with lapse of time. (NEDO)

  15. Achievement report for fiscal 1997 on joint research to develop fuel cell technologies for urban energy centers. Research on evaluating life of phosphoric acid fuel cells; 1997 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu kyodo kenkyu seika hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    This paper discusses life evaluation on phosphoric acid fuel cells of urban energy center type for regional energy supply and on-site type to be installed in buildings. Operation characteristics tests and disassembly checks allow to identify factors for voltage decrease, and estimate the life therefrom particularly if the voltage decrease is caused from catalyst activity. The time before 10% decrease value is reached is now about 40,000 hours. The creep analysis method that has been developed recently can predict deformation in full-size reformers nearly exactly, and is effective in operating the reformer and evaluating the life at the design stage. Creep buckling is the critical value, which is caused by ecliptic deformation of internal tubes in the second catalyst layer. In a heat exchanger for fuel gas preheating, carbon in the reformed gas is carbonized and deposited due to catalytic action of nickel in the brazing material that bonds plates and fins in the heat exchanger. Iron also has a possibility of performing catalytic action. In the on-site type 1,000-kW class fuel cells, no structural problems have been presented even after the operation has been stopped. In order to extend time interval between phosphoric acid supply into the cells, it is necessary to reduce difference in the remaining phosphoric acid amounts in the stack lamination direction and in the cell flat surface. (NEDO)

  16. FY 1999 Report on the technical results. Part 2-1. Development of fuel cell power generation technologies (Research and development of molten carbonate fuel cell power generation system); 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. 2-1. Yoyu tansan'engata nenryo denchi (hatsuden system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This research and development project is aimed at modification and improvement of the stacking technologies, to improve service life and performance of the molten carbonate fuel cell power generation system and reduce its cost. For the cross-flow type stack, optimization of the anode firing conditions leads to controlled reduction of the fine pores, and incorporation of the cathode with MgO successfully leads to controlled elution of NiO and Ni short-cut. For the separator, the service life is extended by treatment of the material with Al and controlling its rigidity. The cell life prediction method is improved to enhance its accuracy. The cell life of -4.3mV/1,000h is achieved by these technologies. For the parallel-flow type stack, the electrodes are improved to achieve the cell life of -1.4mV/1,000h, the technologies for producing the separator for a 1m{sup 2} class unit are developed, and the basic structures of a large-capacity stack are designed. For the internal reforming type, a 200kW class reforming stack is constructed, and operated for 5,259 hours. The causes for electrolyte loss are analyzed by developing the relationships between operating temperature and electrolyte loss, electrolyte mass and sustainability of the cell characteristics, and steam partial pressure over the cathode and electrolyte loss, and also by testing the Ni short-cut. (NEDO)

  17. General report on the results of the development of fuel cell technology such as urban energy center. Evaluation study of life of phosphoric acid fuel cells (fiscal 1995 and 1996); Toshi energy center nado nenryo denchi gijutsu kaihatsu kenkyu seika sogo hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu (1995 kara 1996 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Receiving subsidies from MITI, NEDO carried out this project in fiscal 1995 and 1996 as a joint research with Technology Research Association for Phosphoric Acid Fuel Cell Power Generation System and others. The project aimed at developing the accelerated test method which can evaluate in a short time the cell life of phosphoric acid fuel cells (PAFC) and the lowering of characteristics. The accelerated test method of PAFC life is thought to be a tool indispensable for the promotion of commercialization, but the accelerated test method like the usual material evaluation has not yet been established. To solve this problem, procedures were developed to rationally plan the accelerated test on short stacks of full scale based on the small cell test data. Here, to rationally estimate the operational state under actual conditions based on the data on the accelerated test, it is necessary to fully understand the mechanism of deterioration of PAFC. By conducting in parallel the element study for the basic elucidation of cell deterioration phenomena, obtained was the useful information/knowledge which back up the results of the accelerated test scientifically. 168 figs., 33 tabs.

  18. Achievement report for fiscal 1998 on development of power generation using fuel cells. Research and development of molten carbonate fuel cell (II-2, text of the achievement); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (II-2, kenkyu seika no honbun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    The effort aims at developing a 1000kW-class power plant and also at using gasified coal as fuel in the future. The fuel system facilities include a high-temperature blower. The exhaust heat recovery facilities comprise a heat recovery steam generator (HRSG) and a turbine compressor. As for the electrical system facilities, an inverter is installed, tested, and adjusted. Control system facilities are also tested and adjusted. In relation with the operation of the plant, coordination is conducted about technological and process-related matters with the Kawagoe thermal power station of Chubu Electric Power Co., Inc., where the fuel cell power plant is to be constructed, which is for the smooth execution of a test run. Ceramic-based cathode materials are being developed, which is for the fabrication of stacks improved in performance, higher in current density, longer in life, and lower in cost. Also exerted are efforts at developing multiple-function electrolyte plates and metallic materials (for example for separator plating). The extent of the acceptability of impurities concentration and gas refining systems are also under study, which is to prepare for future coal gasification. Reference is also made to the study of a total system. (NEDO)

  19. FY 2000 report on the results of the infrastructure construction project for spreading high-efficiency fuel cell systems/development of test apparatuses for evaluation of fuel cell systems for automobiles; 2000 nendo kokoritsu nenryo denchi system kiban gijutsu kaihatsu / jidoshayo nenryo denchi system hyoka shiken sochi no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project studies the testing/evaluation methods for spreading fuel cells for automobiles. Described herein are the FY 2000 results. The problems involved in evaluation of the single cell units are classified into those involved in the cell construction and methods of evaluating the operation performances of the single cell units. These problems are analyzed mainly by literature survey. The mode simulation tests will be greatly simplified, if the system can be tested on the bench without being actually boarded on the vehicle. Therefore, this project is aimed at development of a comprehensive mode simulator which can be automatically operated corresponding to the running modes of various countries, to test the performance of FCEV and to examine the effects of each component independently on the vehicle performance. The factors required to reproduce the actual driving states of an FCEV on the bench are analyzed, and the conceptual designs are drawn for the controlling algorithms. It is necessary to standardize the stack and reformer testing methods, in order to evaluate the fuel cell system components. For these objects, the prototype units are constructed to evaluate 10kW direct hydrogen type stacks and 5kW methanol reformers. The units are also constructed to evaluate the high-pressure (1MPa) reformer reactors and hydrogen separation membrane systems. (NEDO)

  20. Report on achievement in developing fuel cell power generation technology in fiscal 1998. Research and development of molten carbonate fuel cell power generation system (Summary of the research result); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (kenkyu seika no yoyaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Based on the achievement made in the second term plan of researching and developing a molten carbonate fuel cell power generation system, attempts are made on extending the service life, improving the performance, and reducing the cost. At the same time, lamination, cooling and operation technologies will be established, and a 1000-kW class power generation plant will be developed. Realization of use of coal gasified fuel in the future is aimed. Stack materials and their processing technologies will be developed, the cell durability will be improved, and the total system research will be carried out. This paper describes the achievements made during fiscal 1998. A process and control (PAC) test was performed on the fuel system facilities in the 1000-kW class generation plant, and its result was analyzed. The fuel system facilities had the test program using simulated fuel cells set from the system side digested nearly completely, verifying that actions can be taken for operation using actual fuel cells to be executed in fiscal 1999. Analysis of the test result presented raw material conversion rate of 96.6% or higher, generation of hydrogen plus CO of 740 m{sup 3} N/h, and NOx generation of 10 ppm or less. Stable combustion of a low calorie gas (500 kcal/m{sup 3} N) was achieved, completing all of the research objectives planned for fiscal 1998. (NEDO)

  1. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. Development of the infrastructure to spread stationary polymer electrolyte fuel cell (PEFC) systems; 2000 nendo nenryo denchi fukyu kiban seibi seika hokokusho. Teichiyo kotai kobunshigata nenryo denchi no fukyu kiban seibi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the FY 2000 studies on development of the infrastructures necessary for introduction and spread of stationary polymer electrolyte fuel cell (PEFC) systems. This project is aimed at establishment of testing and evaluation methods for safety, reliability, performance and so on, and collection of the data, both domestic and foreign, for drafting rules and standardization. The methods are studied to collect the data for the start-up/shut-down operations and rated-load/partial-load operations; establishing the methods for safety evaluation when inert gas purging is dispensed with; and dependence of the cell stack on current, carbon monoxide concentration and cell temperature to establish the basic performance testing methods. The makers are independently developing the stationary PEFC systems, and the data of the selected systems are collected individually as the test systems. The cell stacks also adopt different humidification and cooling methods by makers, and they are tested and their data are collected and analyzed, in order to establish the common testing methods. (NEDO)

  2. Achievement report for fiscal 1998 on development of power generation using fuel cells. Research and development of molten carbonate fuel cell (II-2, text of the achievement); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (II-2, kenkyu seika no honbun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    The effort aims at developing a 1000kW-class power plant and also at using gasified coal as fuel in the future. The fuel system facilities include a high-temperature blower. The exhaust heat recovery facilities comprise a heat recovery steam generator (HRSG) and a turbine compressor. As for the electrical system facilities, an inverter is installed, tested, and adjusted. Control system facilities are also tested and adjusted. In relation with the operation of the plant, coordination is conducted about technological and process-related matters with the Kawagoe thermal power station of Chubu Electric Power Co., Inc., where the fuel cell power plant is to be constructed, which is for the smooth execution of a test run. Ceramic-based cathode materials are being developed, which is for the fabrication of stacks improved in performance, higher in current density, longer in life, and lower in cost. Also exerted are efforts at developing multiple-function electrolyte plates and metallic materials (for example for separator plating). The extent of the acceptability of impurities concentration and gas refining systems are also under study, which is to prepare for future coal gasification. Reference is also made to the study of a total system. (NEDO)

  3. FY 1999 Report on the technical results. Part 1. Development of fuel cell power generation technologies (Research and development of molten carbonate fuel cell power generation system); 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. 1. Yoyu tansan'engata nenryo denchi (hatsuden system no kenknyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This research and development project is aimed at development of the stacking, cooling and operating technologies for the molten carbonate fuel cell power generation systems, to improve service life and performance of these systems and reduce their cost, based on the results obtained so far by the FY 1993. The R and D efforts are directed to (1) technologies for improving stack performance, (2) development of the plant system by operating a 1,000kW class power generation system, and (3) support technologies, e.g., those for stack materials. The item (1) studies 3 stack types, cross-flow, parallel-flow and internal reforming types, including the electrodes, electrolyte-supporting bases and improvement of performance and service life by separator reforming for the cross-flow and parallel-flow types, and installation and operation of a 200kW class stack system for the internal reforming type, where cells are assembled into the system and tested for their operability, after the auxiliary units are PAC-tested. The item (2) installs a 1,000kW class plant, which is operated, after clearing the requirements set by the related laws, e.g., Electric Utility Industry Law, for starting the operation, to achieve the intended targets. The item (3) includes development of the technologies for stack materials, technologies for handling gases produced by coal gasification, and studies on the total systems. (NEDO)

  4. Fuel cell heat utilization system; Nenryo denchi netsuriyo sochi

    Energy Technology Data Exchange (ETDEWEB)

    Urata, T. [Tokyo (Japan); Omura, T. [Tokyo (Japan)

    1995-07-04

    In the conventional fuel cell heat utilization system, the waste heat is recovered to be utilized by either the waste heat recovery heat exchanger or the waste heat recovery steam. In the employment of the waste heat recovery heat exchanger system, however, the utility value is decreased when the temperature of the waste heat is lowered. Contrarily, in the employment of the waste heat recovery steam system, the supplementary water requirement is increased corresponding to the amount of waste heat recovery steam, resulting in the cost increase for water treatment. This invention solves the problem. In the invented fuel cell heat utilization system, a pressurized water from the steam separator is introduced into the second circuit to utilize directly the heat in the heat utilization system without employing the heat exchanger. If a blowdown valve is installed between the second circuit heat utilization system and the steam separator, the heat loss due to the blowdown can be reduced, since the low temperature water is blown down after being utilized in the heat utilization system. 4 figs.

  5. Report on results of development of fuel cell power generation technology 1998. Research and development on polymer electrolyte fuel cell (technological development of element, research on ion exchange membrane for practicability of high performance cell); 1998 nendo seika hokokusho. Nenryo denchi hatsuden gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, yoso kenkyu kaihatsu (koseino denchi jitsuyoka no tame no ion kokan maku ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper explains the results during fiscal 1998 of ion exchange membranes in the development of polymer electrolyte fuel cells. Studies were made on three kinds of standard and two kinds of experimental membranes selected among the Flemion membranes, which are perfluorosulfonic acid membranes made by Asahi Glass Co.,Ltd., and also on the Nafion membranes by Dupon as reference. As the resistance evaluation of the environmental cycle for the membranes, a temperature cycle test was carried out, with the characteristics measured such as moisture content, membrane resistance, mechanical properties, and gas permeability, so that the effects were examined of the temperature cycle on the membranes. Evaluation was also commenced on the water permeability, an important substance-moving characteristic of ion exchange membranes. In the evaluation of the characteristics of membrane-electrode assemblies, the environmental cycle test was performed by joining electrodes to membranes, with the evaluation similarly made as for the membranes alone. On the basis of a correlation between the water permeability and the cell performance, studies were made on the effect of thickness of the membranes on the cell performances. A continuous stability/durability operation of 3,500 hours was verified using Flemion R. As for membrane reinforcement, studies were continued on the cloth and fibril reinforcements as in the previous year.(NEDO)

  6. Fiscal 2000 research report on the energy consumption survey for popularizing stationary fuel cell systems; 2000 nendo teichiyo nenryo denchi no fukyu wo mokutekito shita energy no shohi ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted about the current state of domestic energy consumption for studying the feasibility of a stationary energy system using the polymer electrolyte fuel cell. A study relative to domestic energy consumption dealt with transition in the energy consumption rate, dependence on locality, and the effect of the makeup of residences. The monthly and hourly patterns of demand for heat for hot-water supply were referred to power consumption data broken down by time zone, and it was found that approximately 1kW output would be suitable for this purpose. A study was made about the pattern of operation that such a fuel cell system should follow, and it was learned that a pattern in which 'the system operates according to the imposed load starting at seven o'clock in the morning when the electricity rate switches to the higher and the output does not exceed what is necessary to meet the daily demand for heat.' This method was found to assure the most efficient way of operation covering more than 80% of the need for hot water and electricity. In a study of consumption of energy for business, feasibility was suggested to exist in the installation of systems of 30kW or less at small hotels, barber shops and beauty parlors, restaurants, schools equipped with minor-scale food service, small hospitals, clinics, and the like. (NEDO)

  7. Fiscal 1996 survey report. Data collection and evaluation analysis in the project on field tests on the fuel cell generation; 1996 nendo kenkyu hokokusho. Nenryo denchi hatsuden field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper installed fuel cell power generation equipment experimentally at various facilities which are the final diffusion form of the new energy power generation, conducted long-term operation under the actual load, collected/analyzed various data, arranged them as data useful for full scale introduction/diffusion, aiming at forming the base for general diffusion of the fuel cell power generation. The number of the systems installed for field test execution has been 24 places/28 units since the start of the project, and the system capacity totaled 4,250kW. The actual operation hours in five years are 6,000-28,000. In fiscal 1996, the average cumulative accumulated operational rate was approximately 68%, a little over that in fiscal 1995, 65%. The average load factor was 69% in fiscal 1995 and 70% in fiscal 1996. The utilization rate increased as a whole to about 57% on average if seeing only fiscal 1996, as compared with that in fiscal 1995, about 48%. The power generating efficiency was approximately 34% on average. As to the status of shutdown of the fuel cell power generation, the paper surveyed the average interval of failure, the rate of frequency of shutdown, the analysis of shutdown, etc. 250 figs., 29 tabs.

  8. Survey for making a data book related to the development of new energy technology. Fuel cell; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To proceed with the systematical arrangement of the new energy related data, this survey collected the data relating to fuel cells, and systematized them with the aim of making a data book related to fuel cells. Further, fuel cells are still developing, and therefore, the trend of development in this one year was roughly seen to make it the data toward the future development. This data book is composed of Part 1 (the world development trend in FY 1999) and Part 2 (data book). Part 1 was divided into the fixed power system (Chapter 1), fuel cell vehicle (Chapter 2), and selection of fuel (Chapter 3). The book has a big feature that the selection of fuel was added as an individual chapter, which is a difference from that of FY 1998. In the description of the developmental trend of fuel cell vehicle (FCV) in Chapter 2, the results of the present development and the trend were described in line with the subjects in achieving the commercialization of FCV. Part 2 is a data book which indicates the state of technology development of each of various fuel cells such as actual results of the demonstrative operation of fuel cells in Japan and abroad. (NEDO)

  9. Fiscal 1998 research report. Survey on data collection for development of new energy technology (fuel cell); 1998 nendo chosa hokokusho. Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (nenryo denchi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report is composed of Part 1: the development trend of fuel cells in fiscal 1998, and Part 2: the collected data and appendices. Part 1 includes 4 chapters, (1) The outline of the development trend, (2) Stationary fuel cell, (3) The development trend of fuel cell vehicles, and (4) The development trend of small transportable fuel cells. The report newly includes the development trend of small-capacity fuel cells and the report on 1998 Fuel Cell Seminar notable as an international conference on fuel cell summarizing the trend of fuel cells in fiscal 1998, as compared with the fiscal 1997 report. Part 2 is the collected data on domestic and foreign demonstration operation results of fuel cells, and technical development of every fuel cell. In addition to various collected data on the whole of fuel cells and their use techniques, Part 2 includes the principle, features, system configuration, performance simulation technique, application and market analysis of fuel cells, and the national policy and concerned laws on a subsidy system for introduction of fuel cells, for example. (NEDO)

  10. FY 1994 report on the results of the R and D of solid oxide fuel cells (SOFC); 1994 nendo SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Development of fuel cell power generation technology and R and D of solid oxide fuel cells were carried out, and reports of the FY 1994 results of companies were summed up. As to the R and D of the cell module, R and D were conducted of 'large area cell' by Fuji Electric Corporate R and D, Ltd. and 'combined cell module' by Sanyo Electric Co. As to the R and D of materials/basic technology, the following were conducted: 'R and D of the electrode micro structure' by Japan Fine Ceramics Center, 'R and D of the electrode structure by thermal spraying method by Fujikura Ltd., 'R and D of the multi-functional fuel electrode' by Mitsubishi Heavy Industries, Ltd., 'R and D of the cofiring technology' by Murata Mfg. Co., and 'R and D of the current collecting technology' by Mitsui Engineering and Shipbuilding Co. Concerning the R and D of the system, 'the system study' by Central Research Institute of Electric Power Industry' and 'development of element technology for periphery devices' by The Japan Research and Development Center for Metals. (NEDO)

  11. FY1992 research report on the evaluation and analysis of data collected in fuel cell power generation field test project; 1992 nendo nenryo denchi hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper describes the achievements in fiscal 1992 in the field tests on fuel cell power generation systems. The three locations subjected to the present analysis are all installed with 50-kW systems, whereas power generation efficiency of around 35% such as 35.3, 34.2 and 34.6% was obtained when the systems were operated at the rated output. When the load gets to below a certain load band (about 30 kW), the power generation efficiency decreases proportionately with the load. The overall efficiency including heat supply was 77.8, 70.7 and 80.3% respectively at about the rated output, showing a trend that the higher the thermal efficiency, the higher the overall efficiency. The case of generating both electric power and heat simultaneously has higher efficiency than the case of heat supply alone. The contribution rate of the fuel cell as a base load was 2.8, 4.6 and 13.6%, respectively. The system with as high value as 13.6% takes a power load following type operation mode, in which power is generated during a time band with large load during weekdays, and no power is generated at nighttime and in holidays when load is smaller, playing a role of peak responding power supply. Only one trouble has occurred in an auxiliary generator in the heat recovery system. (NEDO)

  12. FY 1994 Report on the results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers; 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu saiteki donyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Described herein are the FY 1994 results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers or the like. The necessary economic conditions for introduction of a fuel cell system to be competitive with the conventional system which individually supplies electric power and heat are 250,000 yen/kW as the construction unit cost, 0.10m{sup 2}/kW as the installation area, 5 years as the cell body life, use of an inexpensive fuel gas (2 to 6 yen/Mcal). Moreover, it is an indoor system which shall have the operational characteristics to follow daily demand fluctuations while operating under the optimum conditions in the urban redevelopment area considered. A 5,000kW-class fuel cell plant burning fuel gas (2 yen/Mcal) will need a total floor area of approximately 400,000 m{sup 2} in an energy-intensive office type demand area. These conditions shall be met in order to economically introduce the 5,000kW-class plant. It is also necessary to compare the plant with the competitive cogeneration plants. The specifications for the prototype now under consideration are sufficient for the energy-saving effect, and it is premised that these specifications and characteristics are secured. (NEDO)

  13. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. For safety and environmental factors; 2000 nendo jidoshayo nenryo denchi no fukyu kiban seibi seika hokokusho. Anzensei shuhen kankyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the FY 2000 activities for safety and environmental factors involved in fuel cell powdered vehicles. The current technical standards and specifications for CNG and LPG fueled vehicles are investigated, to extract the factors necessary to establish the safety evaluation guidelines when these fuels are replaced by hydrogen fuel. The rules extracted and studied include those related to collision and resultant fuel leakage, removal of spark and hot sources, leakage in the fuel system, leakage into containers and passenger rooms, and materials. For the rules on test methods of fuel tanks, the investigated items include fire resistance, impact resistance and permeation loss of fuel from the tanks. For system safety, the investigated items include possible unusual situations, leakage of the electrolytes and electrical shock. The basic data are collected for destruction of the fuel tanks, spout of hydrogen from and electrification of the hydrogen-occluding alloys, flame retardancy of high-voltage wires for automobiles, and hydrogen diffusion simulation. The safety-related technical trends are followed by hearing the related organizations, including automakers. Literature survey and hearing are conducted to investigate the environmental effects of radio wave interference and noise. (NEDO)

  14. FY 1994 report on the results of the R and D of solid oxide fuel cells (SOFC); 1994 nendo SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Development of fuel cell power generation technology and R and D of solid oxide fuel cells were carried out, and reports of the FY 1994 results of companies were summed up. As to the R and D of the cell module, R and D were conducted of 'large area cell' by Fuji Electric Corporate R and D, Ltd. and 'combined cell module' by Sanyo Electric Co. As to the R and D of materials/basic technology, the following were conducted: 'R and D of the electrode micro structure' by Japan Fine Ceramics Center, 'R and D of the electrode structure by thermal spraying method by Fujikura Ltd., 'R and D of the multi-functional fuel electrode' by Mitsubishi Heavy Industries, Ltd., 'R and D of the cofiring technology' by Murata Mfg. Co., and 'R and D of the current collecting technology' by Mitsui Engineering and Shipbuilding Co. Concerning the R and D of the system, 'the system study' by Central Research Institute of Electric Power Industry' and 'development of element technology for periphery devices' by The Japan Research and Development Center for Metals. (NEDO)

  15. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. Establishment of the base data for fuel quality standardization; 2000 nendo jidoshayo nenryo denchi no fukyu kiban seibi seika hokokusho. Nenryo seijo kikakuka no tame no base data chikuseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at studies on the effects of impurities and additives in hydrogen and methanol fuels, to establish the base data for fuel quality standardization and thereby to promote use of fuel cells for automobiles. Described herein are the FY 2000 results. Literature survey is conducted for the effects of the impurities on performance of the cells and hydrogen-occluding alloys, and various additives for improving safety, e.g., odorants, flame visualizers for hydrogen, and fuel colorants and flame visualizers for methanol. Under the present standards, the cell and alloy performance may be affected by the impurities, e.g., CO and sulfur compounds. The commercial products are sampled, to analyze the impurity components and their concentrations. Hydrogen produced by various processes contains a high proportion of CO before being refined, which may adversely affect the performance. Methanol sampled from less frequently used refilling stations contains high proportions of carbonyl compounds, and it is necessary to confirm their effects of the reformer. In order to investigate the effects of impurities, the performance tests are conducted using the test apparatuses for performance evaluation of power generation by fuel cells and hydrogen-occluding alloys. Propane is found to be an effective flame visualizer for hydrogen, but should be contained at 5% or more to visualize the flame. (NEDO)

  16. FY 2000 report on the results of development of technology for commercializing high-efficiency fuel cell systems. Development of technology for commercializing high-efficiency fuel cell systems (Development of technology for effective utilization of power produced by polymer electrolyte fuel cell systems); 2000 nendo kokoritsu nenryo denchi system jitsuyoka gijutsu kaihatsu seika hokokusho. Kotai kobunshigata nenryo denchi no shutsuryoku yuko riyo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at development of technologies for effective utilization of power produced by polymer electrolyte fuel cell (PEFC) systems and waste heat, to spread cogeneration systems incorporating PEFC systems for residential purposes. Described herein are the FY 2000 results. The program for high-efficiency peripherals for residential PFEC systems attempts use of GaN-FET as the semiconductor device of wide band gap and high breakdown voltage to realize conversion efficiency over 90% by improving inverter efficiency. Two types of the prototype heat recovery systems are developed for the PEFC, one incorporating a latent heat cooling system and the other a water cooling system, to improve heat recovery efficiency and increase heat recovery temperature. The program for technology to fit PEFC output to energy demand develops hot water supply systems provided with a hot water storage function for stable supply of hot water irrespective of the heat recovery conditions, and also with a back-up function with burners. The program also develops the PEFC system of fine load following characteristics, for which pure hydrogen is used as the fuel to allow the system to instantaneously follow fluctuating loads. The program for high-efficiency partial load operation technology studies a 1kW-class residential PEFC cogeneration system incorporating a power storage device for high-efficiency operation at partial loads, where the former operates in a high output mode while the latter absorbs fluctuating loads. (NEDO)

  17. Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

  18. Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 1/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 1/3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include a test of the motor-operated valve, individual test of the gasification furnace circulation water pump, individual test of the motor for the same, individual test of the SGC (syngas cooler) circulation water pump, individual test of the coal feeder rotary valve, individual test of the foreign matters extraction rotary valve, individual test of the foreign matters classifier, individual test of the char feeder rotary valve, individual test of the slag conveyer, individual test of the slag vibrator, individual test of the slag crusher, individual test of the slag separation tank exhaust blower, individual test of the slag separator water pump, test of gasification furnace interlocking, verification test of alert for the same, test of gasification furnace system pressure rise, test of oxygen line ventilation, test of comprehensive purge master sequence, verification test of distribution performance of the distributor, test on char system rock hopper pressure application and pressure release, test of pneumatic actuator valve loop, actual operational test of the soot blower, and an individual test of the receiving conveyer. (NEDO)

  19. Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 3/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 3/3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include a test operation of the expansion turbine in the air separation facility, test operation of the lubricating oil pump for the expansion turbine in the same, test operation of the oxygen compressor in the same, test operation of the medium pressure nitrogen compressor in the same, test operation of the lubricating oil pump for the medium pressure nitrogen compressor in the same, test operation of the high pressure nitrogen compressor in the same, performance verification test for the air separation facility, sequence test for upper/lower stage normal pressure coal hopper purge master in the gasification facility, sequence test for upper/lower stage initial coal loading master in the same, sequence test for char system rock hopper pressure application master in the same, sequence test for gasification furnace light oil leak check master in the same, sequence test for coal rock hopper pressure application master in the same, sequence test for upper/lower coal rock hopper coal reception master in the same, sequence test for slag hopper quenching operation master in the same, and sequence test for gasification steam drum water filling master in the same. (NEDO)

  20. Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 2/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 2/3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include an individual test of the receiving pit hopper vibrator, individual test of the pulverized coal related rotary valve, individual test of the pretreatment compressed air fan, individual test of the coal pulverizer lubricating device, individual test of the coal pulverizer pressure device, individual test of the coal pulverizer, individual test of the coal pulverizer motor, individual test of the coal feeder, individual test of the pulverized coal bunker exhaust fan, individual test of the pulverized coal bunker exhaust fan motor, test of capacity for pulverized coal, individual test of the pulverized coal conveyer blower, test of the sequence of the same, test of pulverizer inert clearing, individual test of the pretreatment condensed water pump in the coal pretreatment device, test of airborne conveyance in the same, verification test of inter-hopper transfer in the same, test of coal pulverization in the same, test operation of the raw material air/low pressure nitrogen compressor in the air separation facility, test operation of the raw material air freezer in the same, and a test operation of the MS adsorber/MS regeneration electric heater. (NEDO)

  1. Water supply method to the fuel cell cooling water system; Nenryo denchi reikyakusuikei eno kyusui hoho

    Energy Technology Data Exchange (ETDEWEB)

    Urata, T. [Tokyo (Japan); Nishida, S. [Tokyo (Japan)

    1996-12-17

    The conventional fuel cell has long cooling water piping ranging from the fuel cell exit to the steam separator; in addition, the supply water is cooler than the cooling water. When the amount of supply water increases, the temperature of the cooling water is lowered, and the pressure fluctuation in the steam separator becomes larger. This invention relates to the water supply method of opening the supply water valve and supplying water from the supply water system to the cooling water system in accordance with the signal of the level sensor of the steam separator, wherein opening and closing of the supply valve are repeated during water supply. According to the method the pressure drop in every water supply becomes negligibly small; therefore, the pressure fluctuation of the cooling water system can be made small. The interval of the supply water valve from opening to closing is preferably from 3 seconds to 2 minutes. The method is effective when equipment for recovering heat from the cooling water is installed in the downstream pipeline of the fuel cell. 2 figs.

  2. Development of MCFC and PEFC technologies; Jisedai nenryo denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hori, M; Ozu, H; Sonai, A [Toshiba Corp. Tokyo (Japan)

    1996-06-01

    Next-generation fuel cells under development by Toshiba Corporation are outlined. The molten carbonate fuel cell (MCFC) has become stable in performance, which results from the conversion of the matrix group from the {gamma}-type to {alpha}-type LiAlO2. The cathode material is expected to withstand the elution of electrolyte for 20000 hours. The soft structure separator developed for stack constitution is expected to improve electrical contact and reduce the cost of stack. An appliance has been completed to tentatively produce every element concerned. During an actual operation, the structural soundness of the 2-cell stack was confirmed by thermal load tests. As for the polymer electrolyte fuel cell (PEFC), an interior humidification method has been developed using a porous material for supplying water to the polymer film. The amount of moisture can be controlled, which will enable a larger-area cell. A 1kW-class stack with a world-record-level 1200cm{sup 2} electrode area has been developed, which stack has shown that the target output has been attained. Furthermore, the power generation efficiency of the system including fuel treatment has been examined. 10 figs.

  3. Manufacturing method of molten carbonate fuel cell. Yoyu tansan prime en nenryo denchi no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Muneuchi, Atsuo; Murata, Kenji

    1989-09-14

    An fuel electrode of a molten carbonate fuel cell is preliminarily dipped with molten carbonate. This operation is troublesome and reduces the productivity because this operation is made by the fuel electrode unit. In this invention, the carbonate is dipped in the process of temperature elevation after the assembly of the fuel cell. In other words, the carbonate electrode is buried in a groove formed in the fuel electrode leaving a gas flowing space; this fuel electrode is layer-built with a matrix and an oxidant electrode to form a unit cell; this unit cell is assembled to compose a fuel cell; while an anti-oxidant gas is fed to a groove of the fuel electrode, temperature is raised up to the operation level, wherein the carbonnate in the groove is molten to be dipped into the fuel electrode. The anti-oxidant gas is such inactive ones as carbon dioxide, nitrogen, argon and helium. 2 figs.

  4. Gas replacement system for fuel cell. Nenryo denchi no gas chikan hoshiki

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, T

    1990-02-14

    When stopping the operation of a fuel cell, the gas in the reaction gas system is purged using such an inert gas as nitrogen for inactivation. A gas source such as inert gas bomb must be prepared beforehand for the purpose. This invention relates to a method of production of inert gas from the air collected from atmosphere to use it as the purge gas. The air collected from the atmosphere is passed through an oxygen remover filled with oxidation catalyst to remove oxygen, and dehumidified by a dehumidifier filled with drying agent, the obtained inert drying gas with nitrogen as the main constituent being used as the purge gas. Copper system catalyst supported by silica is used as the oxidation catalyst, and silica gel as the drying agent. After the operation of the fuel cell is re-started, a part of the high temperature fuel gas extracted from the reaction gas system is introduced to the oxygen remover for the reduction of oxidation catalyst and for heat regeneration of dehumidifying agent by the contained hydrogen. 1 fig.

  5. Molten carbonate fuel cell power generation system. Yoyu tansan prime en gata nenryo denchi hatsuden sochi

    Energy Technology Data Exchange (ETDEWEB)

    Uematsu, K; Hatori, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1991-11-01

    In an indirect internal reforming type molten carbonate fuel cell, the reforming temperature is limited less than the operating temperature of the fuel cell, as the heat source for reforming is depended on the reaction heat at about 650 {degree} C of the fuel cell. To improve the reforming rate at the low temperature range, it is considered to increase S/C (ratio of steam to carbon), but this scheme will cause such problems as to increase the voltage drop of the anode, to drop the heat recovery ratio on the cogenerator, to increase the capacity of the heat exchanger, etc. In this invention, in the power generating plant of a molten carbonate fuel cell the inert gas is added to the reforming raw gas, and in addition to the above the gas is mixed with steam and led into the reforming chamber of the plant. When the inert gas which is not directly concerned in the reforming reaction is added to, total mol number increases and the reforming reaction is acceralated. Consequently, the reforming rate can be raised, though the reforming temperature is low. 2 figs.

  6. Survey on commercial use of fuel cells; Nenryo denchi ni kansuru jitsuyoka no tame no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The basic survey was carried out for the future approach to R & D of fuel cells. Phosphoric acid fuel cell (PAFC) is in the stage of demonstration research and field test supported by subsidy after the end of Sunshine project. Its reliability and durability problems are being solved, and its cost reduction is only one problem for practical use. Distributed systems or on-site systems will be used utilizing its excellent environmental characteristics. Molten carbonate fuel cell (MCFC), solid oxide one (SOFC) and polymer electrolyte one (PEFC) under development were thus surveyed. The following are surveyed: (1) Contribution to a human society such as improvement of energy demand/supply structure and environmental protection, (2) Technological items such as outlook for R & D, validity of developmental issues, comparison between various R & D and significance in industrial promotion, (3) Economic items such as profitability and feasible period, and (4) Social items such as sociability, compatibility to needs, possibility of locations, international meaning, market scale and promotion scenario. 90 refs., 67 figs., 96 tabs.

  7. FY 2000 report on the results of the development of transportation use and residential/commercial use high efficiency energy system technology. R and D of polymer electrolyte cells (Research on ion exchange membranes for commercialization of highly durable cells); 2000 nendo unyu minsei you kokoritsu energy system gijutsu kaihatsu seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu (Kotaikyusei denchi jitsuyoka no tame no ion kokanmaku ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to ion exchange membranes for fuel cells, the R and D were made with the aim of clarifying the characteristics of the membrane required to realize highly durable modules and of demonstrating durability of membrane, and the FY 2000 results were reported. Concerning the low ion exchange capacity thin membrane, the following were confirmed: in perfluorosulfonic acid with ion exchange capacity of 0.84-1.0, the lower the ion exchange capacity is, the greater characteristics of mechanical strength are improved; the optimization of membrane thickness makes the design which satisfies cell characteristics and mechanical strength characteristics possible. In the durability test by medium-/long-term continued operation using each of small unit cell and large unit cell, the results of the stable operation of 5,000 hours using S1102 and S1201Q membranes were obtained. About effects of methanol, changes were observed in creep characteristics and piercing strength in the test on the environmental cycle at -40 degrees C to 80 degrees C. The membrane of low ion exchange capacity kept high elastic modulus even after the treatment at 120 degrees C, which indicated its usability for the higher temperature operation. (NEDO)

  8. FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on fuel cell system); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Nenryo denchi system kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    In this paper, surveys were conducted on 'the developmental situation of the body of fuel cell' and 'the performance required for the inverter connecting fuel cell and electric power system and the peripheral device, and fuel cell.' However, the economical evaluation was to be made at an appropriate time, and the FY 1974 survey was limited to the technology. The results of the investigational study made based on the above-mentioned policy were described in and after Chapter 2. In Chapter 2, described were the prospects of fuel cell and the guide for this fiscal year. In Chapter 3, the relative evaluation of various kinds of fuel cells in terms of the following: electrode structure, catalyst, cell stack, auxiliary machine, dynamic characteristics of cell, efficiency, life, reliability, maintenance, safety, environmental safety, construction cost, maintenance/running cost, and material cost. In Chapter 4, the present technical situation of inverter and the peripheral device, and the situation of the future R and D in Japan and abroad. In Chapter 5, the positioning of the fuel cell system in the hydrogen energy system, and various kinds of performance required for structural elements. (NEDO)

  9. 1998 Annual Study Report. Research and development of solid polymer type fuel cells (Development of techniques for power generation systems and several tens kW class, distributed power source systems); 1998 nendo seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu (hatsuden system gijutsu no kaihatsu / koden'atsugata su 10kW kyu bunsan dengen system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The cells are tested using a CO-containing synthetic reforming gas in 1998, to verify the long-term characteristics of the solid polymer type fuel cells. The cells, equipped with the anode catalyst developed therefor, are tested for extended periods, to confirm the performance and stability in the synthetic gas flow. For development of the catalyst, the optimum content of Ru in the Pt and Ru alloy composition is determined. For the cell tests, the single- and 3-cell units are tested for extended periods. For verification of commercial viability of the stacked cell systems, the cell-humidifying techniques are developed, which can uniformly humidify each cell in the stacked unit with a number of cells, after investigating the effects of temporal changes in water permeability, pretreatment conditions and film thickness. These techniques are used to develop and operate a 10kW, stacked cell unit, which successfully generates power of 10.6 kW at the rated current density, exceeding the target of 10 kW. For development of design bases for compact fuel treatment system, the techniques which allow reduction of CO concentration to 10 ppm or less at high repeatability are developed. (NEDO)

  10. Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and researches on peripheral technologies (Research on fuel cell systems); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Nenryo denchi system kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This paper discusses hydrogen fuel cell systems. In the economic performance of fuel cells, the ratio of fuel cost accounting for in the power generation cost is as very high as 66% or higher to 82%, if hydrogen unit cost is in the range of 20 to 50 yen per Nm{sup 3}. Enhancing the power generation efficiency contributes more greatly to reduction of the power generation cost than by reducing the construction cost. There should be no much influence on the power generation cost if a system lasts four to five years. The paper also discusses the discrete type power generation system. Discussions were given on a waste heat recovering fuel cell system using as the model an office building of 16 stories above the ground, with one basement and a total floor area of 16,000 m{sup 2}. If the system can be constructed in such a way that the fuel cell capacity is made slightly larger than that corresponds to power load, and whole air conditioning load can be taken care only by waste heat by using a heat pump, the auxiliary heat source can be made smaller, and the overall fuel conservation ratio can be larger, thus the fuel was found saved by 40% than in existing systems. In using hydrogen in automobiles, weight problem will emerge if high-pressure hydrogen or metallic hydride is used for hydrogen storage. Liquefied hydrogen is light in weight, but large in volume. Development is desired on high-performance hydrogen absorbing alloys. (NEDO)

  11. 1998 Annual Study Report. Research and development of solid polymer type fuel cells (Development of techniques for power generation systems and several tens kW class, distributed power source systems); 1998 nendo seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu (hatsuden system gijutsu no kaihatsu / koden'atsugata su 10kW kyu bunsan dengen system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The cells are tested using a CO-containing synthetic reforming gas in 1998, to verify the long-term characteristics of the solid polymer type fuel cells. The cells, equipped with the anode catalyst developed therefor, are tested for extended periods, to confirm the performance and stability in the synthetic gas flow. For development of the catalyst, the optimum content of Ru in the Pt and Ru alloy composition is determined. For the cell tests, the single- and 3-cell units are tested for extended periods. For verification of commercial viability of the stacked cell systems, the cell-humidifying techniques are developed, which can uniformly humidify each cell in the stacked unit with a number of cells, after investigating the effects of temporal changes in water permeability, pretreatment conditions and film thickness. These techniques are used to develop and operate a 10kW, stacked cell unit, which successfully generates power of 10.6 kW at the rated current density, exceeding the target of 10 kW. For development of design bases for compact fuel treatment system, the techniques which allow reduction of CO concentration to 10 ppm or less at high repeatability are developed. (NEDO)

  12. Fiscal 1997 report on the results of the international standardization R and D. R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Rinsangata nenryo denchi no kasoku jumyo shiken hoho no hyojunka ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As for fuel cells, which are expected as a new clean energy, the R and D are being proceeded with in various fields of the world, but the standardization has not been made both in Japan and abroad. In Japan, the situation is that the information on technical terms, indication method, performance test method, and environment/safety test methods of the phosphorous acid fuel cell power generation is publicly spread. In relation to the international promotion of fuel cells to be predicted, it is necessary to internationally standardize cells themselves which are a key component of fuel cell power generation facilities. Phosphorous acid fuel cells are expected of the earliest commercialization of all, but the common test method to evaluate life characteristics of the cell stack has not been established yet. In the R and D, for the purpose of internationally standardizing test methods to evaluate life characteristics of the cell stack, a study on the acceleration life test method of phosphoric acid fuel cells was conducted in terms of the technical trend, data, standard, etc. A plan was prepared on general rules of the method to test acceleration life at the cell reaction part of the small cell, and activities also were started for setting up a technical committee for the fuel cell power system in President`s Advisory Committee on Future Technology. 29 figs., 20 tabs.

  13. Fiscal 1994 report on technological results. Development of fuel cell technology such as urban energy center (Survey for practical development of optical system of decentralized power source for residential use); 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu seika hokokusho. Minseiyo bunsangata dengen saiteki system jitsuyoka kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Feasibility study was conducted on the technology for practical application of a several kW class fuel cell for the people's livelihood, particularly, for residential use. The study was made in six areas consisting of study on the present state of technology, conceptual design of a small fuel cell, survey on a promising market, basic concept of cell for residential use, feasibility study on application and on introduction. There is no record of development of the several kW class; while the fuel cell excels in the efficiency of energy utilization and the environmental conservation, its performance greatly deteriorates by start and stop under the present technology. Accordingly, it is a prerequisite that the equipment is for an electric heat combined type and for system interconnection. Also, while it is proper that the cell is phosphate type and that the fuel is natural gas, an innovation is necessary in the technology for reforming the cell and the fuel. The conceptual design revealed the possibility of a power generation system having a generating efficiency of 32%, exhaust heat recovery rate of 30%, and dimension of 75x65x150 cm. On the basis of a feasibility study on the application to the combination of a house and a beauty parlor, an advantage was recognized in the fuel unit cost of 5 yen/meal and the equipment cost of 200-250 thousand yen/kW, with demand estimated for 2.5 million installations nationwide including 950 thousand in natural gas supply districts. (NEDO)

  14. Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 6. Development of the polymer electrolyte membrane fuel cell supplied with pure hydrogen; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu seika hokokusho. Task 6. Junsuiso kyokyu kotai kobunshigata nenryo denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on development of element technologies for a pure hydrogen fuel cell power system of nearly 45% in efficiency at terminal, and demonstration test result on the 30kW class polymer electrolyte membrane fuel cell system supplied with pure hydrogen. On cell voltage characteristics in high-utilization operation, study was made on degradation and corrosion caused by short supply of hydrogen by using a single cell. As a result, it was found out that reverse polarization of -3.0V has small effect, however, that of -0.7V causes corrosion and deterioration of cell characteristics in a short time. In operation using actual-size cells for the 30kW class plant, it was effective to wet cells on the air side. On hydrogen high-utilization operation technique, study was made on hydrogen recovery and recycle operation, anode outlet line closed operation, and anode recycle operation. In addition, some studies were made on specifications of auxiliary facilities for fuel cells, safety measures for fuel cells and humidity control of supplied hydrogen gas. (NEDO)

  15. Fiscal 2000 achievement report. Development of coal gas production technology for fuel cells (Research using pilot test facility - for public release); 2000 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the development of a coal gasification furnace optimum for fuel cells, research and development was conducted of a coal gas production technology using the oxygen-blown coal gasification technology, and the fiscal 2000 results are put together. In the construction of the pilot test facility, part of the road in the site was constructed as continued from the preceding fiscal year. In the construction of the coal gasification facility, some of the devices were built, which were the coal feeding system, coal gasification furnace, heat recovery boiler, and the char recovery device, and some of the thus-built devices and procured devices were installed. In the study of the control of the operation of the oxygen-blown coal gasification system, the pilot test facility was divided into unit devices and, for each of the unit devices, detailed procedures for pre-start preparation, start, stop, and for the stop of accessorise were deliberated, and important operating steps were worked out. Timing charts were prepared for the operation of each of the facilities during plant start/stop operations. In the effort to deal with serious accidents, special operation procedures were studied and prepared on the case-by-case basis. (NEDO)

  16. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on fuel cell system); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Nenryo denchi system kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-01

    In fiscal 1974, the domestic and overseas developmental states of fuel cell bodies were surveyed, and some problems on the interconnection between a fuel cell system and power system were studied. Since the maximum outputs of conventional fuel cells are only nearly 10kW, however, those from several hundreds kW to several ten thousands kW are required for buildings or commercial power facilities, in the fiscal 1975, some supposed problems derived from such scale- up of fuel cells were extracted to study their solutions. Study was made on 4 kinds of fuel cells such as alkaline electrolyte, acidic electrolyte, molten salt electrolyte and solid electrolyte fuel cells, and fuel modifier for generating hydrogen. As preliminary modeling work for dynamic performance analysis of fuel cell systems, study was made on scale of the model, DC devices and equipment for customers, environmental impact, power supply reliability, various characteristics and problems in load variation including start and stop, and kinds of accidents and their measures. (NEDO)

  17. Achievement report (edition B) for fiscal 1999 on development of technology to manufacture coal gas for fuel cells. Studies by using pilot test facilities (Volumes for equipment fabrication and constructions, and trial run design); 1999 nendo seika hokokusho (B ban). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot setsubi ni yoru kenkyu (kisokoji kiki seisaku hen shiunten sekkei hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop a coal gas manufacturing system for fuel cells, research and development has been performed on a oxygen-blown coal gasifier and researches on a technology to purify gases for fuel cells. This paper summarizes the achievements in fiscal 1999. The current fiscal year has performed, among other the pilot plant construction works, execution of the above-the-ground constructions for the operation center and compressor room building, construction of the cooling water tanks, and partial improvement of roads in the plant site. In the gasifier facilities, items of equipment were fabricated, some of the outsourced articles were procured, and the installations thereof were carried out. For the gas purifying equipment, installation of the gas analyzer room was executed. In the trial run design, discussions were given on the systematic improvements in the test items, the gas sampling procedures, the unit protecting interlock, and the facility protecting logic. For the trial run design, establishment has been implemented on the efficient and functional test plans by establishing priority on the tests to be executed, so that the development items demanded in the pilot test and research can be achieved within the limited test processes. (NEDO)

  18. Survey report on the status of new energy in the U.S. On-site research centering on fuel cell, hydrogen energy, and wind energy (4th World Energy Engineering Congress); Beikoku shin energy jijo chosa hokokusho. Nenryo denchi, suiso furyoku energy wo chushin to suru jicchi chosa (dai 4 kai World Energy Engineering Congress)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-02-01

    A survey group dispatched by the New Energy Industrial Forum technical development committee conduct researches into the status of technologies in the U.S. relative to fuel cells, hydrogen energy, and wind energy. The group also attend the 4th World Energy Engineering Congress. As for the research and development of the phosphoric acid fuel cell, it is undertaken by the United Technology Corporation, Westinghouse Electric Corporation, and the Engelhard Corporation, each having its own peculiar technologies and thereby avoiding competition with others in one and the same domain. As for the molten carbonate fuel cell, the Argonne National Laboratory is entrusted with the control of technology development, and the Laboratory in turn requests the United Technology Corporation and Westinghouse Electric Corporation to develop technologies and systems. As for the solid oxide fuel cell, the Westinghouse Electric Corporation is entrusted with its development through the intermediary of the Argonne National Laboratory. As for hydrogen energy, the General Electric Company and Westinghouse Electric Corporation develop hydrogen production systems and the Brookhaven National Laboratory develops hydrogen storage systems using metallic hydrides. As for wind power generation, a Bendix-made 3,000kW wind power plant is visited and discussion is held on it. (NEDO)

  19. Achievement report for fiscal 1998. Research and development of polymer electrolyte fuel cell module (Development of 10kW-class transportable power source system of high current density type); 1998 nendo seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu, kodenryu mitsudogata 10kW kyu kahangata dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the development by the end of fiscal 2000 the above-named system which will operate on methanol/air (normal atmospheric pressure) yielding 0.3W/cm{sup 2} or more, efforts are exerted about a high-lamination type PEFC (polymer electrolyte fuel cell) module and a lamination type methanol reformer, this project carried over from fiscal 1997. In relation with the PEFC module, platinum loading was reduced (by 60% from the amount in fiscal 1997) by catalytic layer improvement, cell characteristics were improved, continuous load imposition was performed using a reformed simulation gas, life test was conducted consisting of frequent starts and stops, lamination was built using shaping separators, and a 2kW-class stack was built and evaluated for performance. Next to come is a test run of a 5kW-class stack. In relation with the lamination type methanol, element components were tested. A reformer section and a catalytic combustion section were designed, manufactured, and tested, and a vaporizer section and a CO reduction section were evaluated for performance and life. A 2kW-rate lamination type methanol reformer was designed and built by integrating the said element components, and was subjected to a test run for performance evaluation. (NEDO)

  20. Survey report on the status of new energy in the U.S. On-site research centering on fuel cell, hydrogen energy, and wind energy (Westinghouse Electric Corporation); Beikoku shin energy jijo chosa hokokusho. Nenryo denchi, suiso furyoku energy wo chushin to suru jicchi chosa (Westinghouse Electric Corporation hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-02-01

    Under the auspices of the New Energy Foundation and the New Energy Industrial Forum technical development committee, a survey team is sent to the U.S. and conducts investigations there about fuel cells, hydrogen production, wind power generation, etc. Visited in the U.S. are the Advanced Energy System Division of the Westinghouse Electric Corporation. As for the phosphoric acid fuel cell, research and development is under way so that two 7.5MW demonstration plants will start service operation by 1987. As for the solid oxide fuel cell, a performance test has completed for a 15-cell model, and a life test is now under way. There is a plan to construct a 500kW plant in 1988. In the production of hydrogen by means of the sulfur hybrid decomposition process, a laboratory model with a capacity of 2L/min was built in 1978, and a life test is now under way for the constituent materials and catalysts. In the field of wind power, the Westinghouse Electric Corporation has developed a 200kW generator, which is now in operation in Mexico, Puerto Rico, Rhode Island, and Hawaii. (NEDO)

  1. FY 1999 Results of research and development project for polymer electrolyte fuel cells (PEFCs). Development of high current density type 10kW class portable power source systems; 1999 nendo kotai kobunshigata nenryo denchi no kenkyu kaihatsu seika hokokusho. Kodenryu mitsudogata 10kW kyu kahangata dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Described herein are the FY 1999 results of the research and development project aimed at development of multi-stacked PEFC modules and plate-stack type methanol reformers, and researches on portable power source systems, for development of methanol-air 10kW class (over 0.3W/cm{sup 2}) PEFC systems for portable use by the end of the FY 2000. The programs for the multi-stacked PEFC modules include improvement of tolerance against CO by improvement of catalyst bed and gas passage structures; development of a multi-stacked 5kW class stack structured to prevent fuel starvation; endurance tests conducted at a constant load using a simulated methanol reformate gas; and development, on a trial basis, of the stack using a formed separator. The programs for the plate-stack type methanol reformers include development, on a trial basis, of reforming catalysts integrated with flow passages, combustion catalysts and CO oxidation catalysts, and endurance evaluation tests for the reformer elements. The researches on portable power source systems include studies on, e.g., system control/behavior and efficiency, and basic system designs. The performance and environment endurance tests are also conducted for auxiliary equipment, e.g., blowers. (NEDO)

  2. Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Part 1 - Construction and test operation); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Sono 1 - Koji shiken unten hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the development of a coal gasification furnace optimum for fuel cells, research and development was conducted of a coal gas production technology using the oxygen-blown coal gasification technology, and the fiscal 2001 results are put together. In the construction of the pilot test facility, work involved the road in the site, road illumination system installation in the site, and an unauthorized entry prevention system. In the construction of the coal gasification facility, work involved electrical instrumentation and painting for the coal feeding system, coal gasification furnace, heat recovery boiler, and so forth, and the installation of a series of devices was completed. In July following the completion, power was received and test operations were started, which included the operation of the coal gasification facility alone. Renting was started in August for the coal pretreatment facility, air separation facility, and the slag treatment device. In the study of the operation control technology for the oxygen-blown coal gasification furnace system, test operations were conducted based on the operating procedures prepared in the preceding fiscal year, which included a test operation performed for the pilot test facility alone. Parameters for equipment control obtained through the test operations, and improvements on operating steps carried out as required, were all reflected on the operating procedures. (NEDO)

  3. FY 1999 Report on research and development of power generation by solid electrolyte fuel cell. Research and development of solid electrolyte fuel cell; 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    This project is aimed at establishment of the module basic technology and commercialization of the solid electrolyte fuel cell in the early stage by designing, construction, operation and performance evaluation of a several kW-class module which incorporates the cylindrical cell fabricated by the wet process. The FY 1999 R and D efforts include (1) cell performance demonstration study: the cylindrical single cell fabricated by the wet process is demonstration-tested to determine the initial performance and durability for continuous operation, thereby comparing the external reforming with internal reforming in output, with the internal reforming rate as the parameter, (2) development of a several kW-class module: the adequate cell arrangement structure within the module is studied by the computer-aided simulation, and the tests for confirming thermal cycle durability of the modified bundle are conducted using the module power generation unit and the several kW-class module is tested, and (3) development of the technology for designing a thermally supported module: the effects of, e.g., air and fuel supply conditions on the module performance are analyzed using the analytical model as the base. Expansion of the module level to the process simulation model has been completed, based on these results. (NEDO)

  4. FY 1998 annual report on the development of fuel cell power generation techniques. Research and development of solid electrolyte fuel cells (research results); 1998 nendo nenryo denchi gijutsu kaihatsu. Kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the FY 1998 research and development results of solid electrolyte fuel cells. For R and D of the tubular type cell by the wet processing technique, the tests are conducted to evaluate the initial performance and long-term durability for continuous operation of the single tubular cell. For development of the several-kW class modules, computer-aided simulations are conducted. For R and D of material and substrate techniques, the thermal cycle characteristics, cell characteristics and stress of the cell modules are evaluated, in order to evaluate their reliability. The thermal cycle test results indicate that performance of the single-stage cell is unaffected by the thermal cycles. It is found by the stress evaluation that use of the separator plate having a higher thermal expansion coefficient than the electrolyte plate and use of the sealant having a thermal expansion coefficient close to that of the electrolyte plate are effective means to reduce stresses. For the research to reduce costs of the cell materials, their chemical, mechanical and thermal characteristics are evaluated. For the system research, the areas for which the compact systems are suitable and their optimization are studied. (NEDO)

  5. Report on the results of the FY 1999 R and D of polymer electrolyte fuel cells. Development of the power system technology (Development of high voltage several 10 kW class dispersed generation system); 1999 nendo kotai kobunshigata nenryo denchi no kenkyu kaihatsu seika hokokusho. Hatsuden system gijutsu no kaihatsu (koden'atsugata suju kW kyu bunsan dengen system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the FY 1999 development of polymer electrolyte fuel cell and several 10 kW class dispersed generation system. The humidification of the cell body is the internal humidification method in which water is directly supplied to cell, which makes the cell life long. The cooling using latent heat of vaporization of the water supplied makes the temperature distribution inside the cell face homogeneous. In the test for long life, the system was stably operated at voltage lowering speed of 11mV/1000h. The optimization of water supply structure in the stack increases the latent heat cooling amount and makes the temperature distribution inside the cell face homogeneous. The reduction of CO concentration in reformed gas is extremely important for improvement of cell performance and long-term stabilization of cell voltage. By the two-stage structure selective oxidation device, the CO concentration at inlet, 5,000 ppm, can be reduced to below 10 ppm at outlet. In the demonstrative experiment on the several 10 kW class dispersed generation system, efforts for reduction in size of structural equipment and package were made, and a possible size of 200*150*180cm was obtained. Based on the chart of 30kW class system flow, the heat material balance was analyzed, and the power generation efficiency of 40% at a.c. sending end and overall efficiency of 80% were confirmed. (NEDO)

  6. Report of the FY 1995 research cooperation promotion projects (overall evaluation). Research cooperation in fuel cell utilization/district power generation system and village type technique for simplified continuous production of raw palm oil; 1995 nendo kenkyu kyoryoku suishin jigyo (sogo hyoka) hokokusho. Nenryo denchi katsuyo chiiki hatsuden system ni kansuru kenkyu kyoryoku / sonrakugata kan'i renzoku palm arayu seizo gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The research cooperation project for fuel cell utilization/district power generation system is conducted under the research cooperation agreement between NEDO and Electricity Generating Authority of Thailand (EGAT), to demonstrate a 50 kW pilot plant constructed at EGAT's Bang Pakong power station. The fuel cell reforms self-spouted natural gas into H{sub 2} as the fuel. It has produced a total power of 341,921 kWh under the conditions of cumulative operating time: 8,115.4 hours, longest continuous operating time: 1,100 hours, service factor: 89.64%, load ratio: 86.13% and system utilization factor: 77.20%. The fuel technique will be acceptable for Thailand, if it is economically competitive. The project for producing raw palm oil is for Malaysia. The facilities introduced and tested for the new process are a continuous steam-heated fruit remover, fiber/nut separator, and shell cutter. The new process is evaluated to produce higher-quality raw palm oil in higher yield while consuming less energy. The new process, whose steps are automated, saves operating cost, and suitable for Malaysia which is suffering shortage of manpower. (NEDO)

  7. Study on fuel supplying method and methanol concentration sensor for the high efficient operation of methanol fuel cells. Methanol nenryo denchi no unten ni okeru nenryo kyokyu hoho no kento to methanol nodo sensor no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsukui, Tsutomu; Doi, Ryota; Yasukawa, Saburo; Kuroda, Osamu [Hirachi, Ltd., Tokyo, (Japan)

    1990-01-20

    A fuel supplying method was studied and demonstrated, essential to the high efficient operation of methanol fuel cells. Methanol and water were supplied independently from each tank to an anordic electrolyte tank in a circulating system, detecting a methanol concentration and liquid level of anordic electrolyte by each sensor, respectively. A methanol sensor was also developed to detect accurately the concentration based on electrochemical reaction under a constant voltage. A detection control circuit was insulated from a constant-voltage power supply to prevent external noises. The methanol sensor output was compensated for temperature, and a new level sensing method was adopted to send out a command comparing different responses to electrolyte shortage. As the methanol fuel cell was operated with this fuel supplying system, the stable characteristics of the cell were obtained within the variation of {plus minus} 0.1mol/l from the specified methanol concentration. 6 refs., 17 figs., 1 tab.

  8. Survey on construction of the database for new energy technology development. Fuel cell; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the data related to technological development of new energy, the database for fuel cells was prepared. The major international conferences held in fiscal 1996 were reviewed. As the atmosphere of the whole conference, phosphoric acid fuel cell (PAFC) is in a stage just before practical use, and molten carbonate fuel cell (MCFC) is in a stage of the demonstration study of MW class one. The study on solid oxide fuel cell (SOFC) and polymer electrolyte fuel cell (PEFC) is in considerable progress. In particular, the application of PEFC to automobiles is in real investigation. For the database, kinds and features of various fuel cells, operation principles, system configurations of FC plants, application fields, and characteristics were arranged. Field test examples for public and industrial uses were separately arranged, and in particular, the application examples of PAFC were presented together with developmental conditions of the other fuel cells. Overseas situations were equal to domestic ones, and their marketability was predicted. The Japanese subsidy policy and some U.S. policies were also arranged. 28 refs., 51 figs., 37 tabs.

  9. Investigation on preparing data collections related to new energy technology development. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With an objective to put data related to fuel cells systematically into order, related data were collected comprehensively. Reviewing large international conferences impresses dawn of commercialization in phosphoric acid fuel cells (PAFC), take-off of megawatt-class molten carbonate fuel cells (MCFC), and remarkable advancement in studies on solid oxide fuel cells (SOFC) and polymer electrolyte fuel cells (PEFC). The data collection may be compiled as follows: basic principles, features, operation principles, system configurations, utilization fields, and characteristics were summarized on fuel cell power generation systems using phosphoric acid, polymer, molten carbonate, solid oxide, and alkaline fuel cells; major installation examples in Japan and overseas countries were summarized; investigations were given on developing other fuel cells such as alkaline type and direct methanol type fuel cells; and marketability, subsidies operations in Japan, and states of policy implementation in the U.S.A. were investigated and put into order. 22 refs., 24 figs., 21 tabs.

  10. Electrolyte loss mechanism of molten carbonate fuel cells. 1; Yoyu tansan`engata nenryo denchi ni okeru denkaishitsu loss kiko ni tsuite. 1

    Energy Technology Data Exchange (ETDEWEB)

    Sonai, A; Murata, K [Toshiba Research and Development Center, Kawasaki (Japan)

    1993-11-01

    During a single-cell disassembly test of molten carbonate fuel cells having been operated for 90 hours to 5500 hours, correlativity was discovered between decrease in the retained amount of electrolyte due to decrease in pore capacity of electrodes and electrolyte plates and the electrolyte loss. The electrolyte loss amount cannot be explained with the conventional mechanisms, thereby a new model was proposed. The cathode has shown very little change in the capacity change in pores with diameters smaller than 2 {mu}m per unit area. The anode has remained almost constant after 1000 hours, but the electrolyte plates have shown remarkable decrease. Therefore, it is possible to estimate that the electrolyte plates should have been the major cause for the electrolyte loss. The result of measuring the electrolyte loss amount agreed well with that estimated using pore capacity curves. This fact suggests that the electrolyte loss can be explained by a new mechanism that hypothesizes the existence of a largest size of retaining pores that can support carbonates and defines that the electrolyte loss is generated from decrease in the pore capacity. 7 refs., 8 figs., 1 tab.

  11. Sintering behavior of porous electrolyte supporting matrix for molten carbonate fuel cells; Yoyu tansan`en nenryo denchi denkaishitsu hojiso no shoketsu kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Sonai, A; Murata, K [Toshiba Research and Development Center, Kawasaki (Japan)

    1993-11-01

    Considerations were given on pore distribution in lithium aluminate that supports electrolyte in molten carbonate fuel cells under cell operating condition, and its sintering mechanism by measuring time-based change in the linear contraction. The following findings were obtained: Pore capacity in the lithium aluminate layer has decreased in 1000-hour operation, creating pores with diameters greater than 2 {mu}m in which no carbonates have been filled; the cross-leak in reaction gases and ion resistance in the electrolyte retaining layer have increased resulting in degraded cell performance; the lithium aluminate layer has generated initial quick densification as a result of melting of the carbonates, with the more the liquid phase, the larger the linear contraction; and pores with diameters greater than 2 {mu}m are thought to have been generated as the densification of the lithium aluminate due to dissolution and reprecipitation progresses. The densification can be explained well if this is regarded to consist of a slow densification process in association with sintering of lithium aluminate particles, and progress in a sintering mechanism where solid phase has solubility against liquid phase. 9 refs., 8 figs.

  12. Fundamental analysis of thermally regenerative fuel cell utilizing solar heat; Taiyonetsu wo riyosuru netsu saiseigata nenryo denchi no kiso tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ando, Y; Tanaka, T; Takashima, T; Doi, T [Electrotechnical Laboratory, Tsukuba (Japan); Aosawa, T; Kogoshi, S [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Study was made on a thermally regenerative fuel cell using solar heat. The thermally regenerative fuel cell was devised which is composed of 2-propanol liquid-phase endothermic dehydrogenation at nearly 100degC, and acetone liquid- phase exothermic hydrogenation at nearly 30degC as reverse reaction. This low-temperature dehydrogenation can relatively easily utilize a flat solar heat concentrator. 2-propanol dehydrogenation generates acetone and hydrogen. Generated acetone generates electric power in hydrogenation, generating propanol. This propanol regenerates acetone and hydrogen in dehydrogenation. The activity of Ru and Pt composite catalyst was considerably higher than that of Ru or Pt single catalyst. The activity was also higher in carbon felt or carbon cloth carrier than carbon plate carrier. The open circuit voltage of the fuel cell was estimated to be 110-120mV, nearly consisting with theoretical values. Short circuit current was also estimated to be 9-11mA, suggesting reduction of its internal resistance as an important subject. 4 refs., 5 figs., 2 tabs.

  13. Data book on new energy technology development in FY 1997. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this survey is to grasp the trends of technology development of fuel cells and their market, and to provide data required for supporting the introduction and diffusion of fuel cells. This report consists of Part 1 titled as `Trends of development of fuel cells in FY 1997`, and Part 2 titled as `Compiled data`. The Part 1 consists of three chapters, i.e., Chapter 1 titled as `Introduction`, Chapter 2 as `Development trends of fuel cells for on-site power generation`, and Chapter 3 as `Trends of development of fuel cells for mobile objects and fuel cell-powered vehicles`. The introductory chapter not only outlines the development trends but also describes the results of the 5th Grove Fuel Cell Symposium noticed as the major global international symposium on fuel cell in general and the environmental problems discussed at the COP3 Kyoto Conference, both held in TY 1997. The Part 2 contains the principles, system configurations and applications of fuel cells, PAFC, MCFC, SOFC, PEFC, modifier, DMFC, development trend of fuel cell-powered vehicles, and national policies for fuel cells in Japan. The Appendix features a report of the new technique investigation working group and information on fuel cells from newspapers. 100 refs., 4 figs.

  14. Heat recovery properties from fuel cell system for telecommunications use; Tsushin`yo nenryo denchi system ni okeru hainetsu kaishu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ishizawa, M.; Iida, S.; Abe, I.; Yamamoto, M. [NTT Integrated Information and Energy Systems Laboratories, Tokyo (Japan)

    1997-08-20

    NTT is developing a phosphoric-acid fuel-cell energy system for telecommunication co-generation systems to reduce energy costs and help preserve the environment. Fuel cells are used to provide electrical power to telecommunication equipment and the heat energy that is generated is used by the absorption refrigerators to cool the telecommunication rooms throughout the year. We field-tested this fuel-cell energy system in a telephone office. Two heat recovery methods were applied in the test: one uses direct steam heat recovery from fuel-cell stack coolant to keep the heat recovery temperature high and to avoid requiring a heat exchanger for the recovery; the other uses heat recovery from the reformer exhaust gas that is directly in contact with the heat recovery water to recover heat more economically. Our field tests confirmed that the average efficiency of heat recovery from fuel-cell stack coolant is 16%, and from the reformer exhaust gas is 9% under 80-kW continuous operation. Maximum total efficiency including electrical power efficiency was confirmed to be about 73% under the condition of 100-kW and an S/C ratio of 2.5 in the winter period: heat recovery from the fuel-cell stack coolant was 23%, from the reformer exhaust gas was 10%, and from electrical conversion was about 40%. 9 refs., 12 figs., 1 tab.

  15. Hear recovery properties from fuel cell system for telecommunications use; Tsushin`yo nenryo denchi system no fuirudotesuto ni okeru hainetsu kaishu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ishizawa, M.; Iida, S.; Abe, I.; Amanuma, H. [NTT Integrated Information and Energy Systems Laboratories Tokyo (Japan); Uekusa, T.; Waragai, S. [NTT Power and Building Eacilities Inc., Tokyo (Japan)

    1997-12-20

    NTT is developing a phosphoric acid fuel cell energy system for telecommunication co-generation systems to reduce energy costs and help preserve the environment. Fuel cells are used to provide electrical power to telecommunication equipment and the heat energy that is generated is used by the absorption refrigerator to cool the telecommunication rooms throughout the year. We fieldtested this fuel cell energy system in a telephone office for three years. Heat recovered water from fuel cell stack coolant was supplied to the absorption refrigerator and further extra-heat was recovered by a heat exchanger. The toral heat recovery amount was about 86000 kca/h (the heat recovery efficiency was 20%) under 200kW operation. The absorption refrigerator was supplied about 49000kcal/h of heat and operated with 0.7 of coefficient of performance throughtout the year. The electrical efficiency was maintained more than 38% after 13000h operation. 12 refs., 10 figs., 3 tabs.

  16. Collection of summaries of polymer electrolyte fuel cell research and development reports presented at fiscal 2000 meeting; 2000 nendo kotai kobunshigata nenryo denchi kenkyu kaihatsu seika hokokukai yoshishu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-08

    Contained in this book are the summaries of 26 essays presented at an achievement reporting conference on polymer electrolyte fuel cell (PEFC) research and development held in Tokyo on March 8, 2000. In the development of high-efficiency energy systems for transportation and residential/commercial sectors, 6 essays are summarized, involving ion exchange membranes, normal pressure operation type several kW class power source systems for home use, and so forth. For the practical application of high-efficiency fuel cell systems, 12 essays are summarized, involving technologies of PEFC low cost electrodes, PEFC module manufacturing, hydrogen separation type reforming, PEFC system manufacturing, and so forth. In relation to the establishment of technologies for a fuel cell popularization infrastructure and development of key technologies for high-efficiency fuel cells, 2 essays are summarized, involving the construction of a popularization infrastructure and development of evaluation test equipment, and the like, for automotive fuel cells. In relation to the development of key technologies and verification thereof for the practical application of fuel cells, 6 essays are summarized, covering the research and development of hydrogen producing liquid fuels and hydrogen absorbing alloys. (NEDO)

  17. Electrolyte loss mechanism of molten carbonate fuel cells. 2.; Application to the cell with matrix electrolyte layer; Yoyu tansan`engata nenryo denchi ni okeru denkaishitsu loss kiko ni tsuite. 2.; Matrix gata denkaishitsuso wo yusuru denchi eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Sonai, A; Murata, K [Toshiba Research and Development Center, Kawasaki (Japan)

    1993-11-01

    A single cell of molten carbonate fuel cell using a matrix electrolyte layer fabricated by using the doctor blade process has been operated for several thousand hours, measured of electrolyte loss amount, and analyzed by using a new electrolyte loss mechanism. The result may be summarized as follows: according to a result of measuring the matrix layer pore distribution, the average pore size has increased little by little; pores with diameters greater than 2 {mu}m at which no electrolyte retention becomes possible remain at nearly constant ratio up to 1800 hours, but increased after 2500 hours; the pore capacity in ports with the largest electrolyte retaining diameter of 2 {mu}m or less showed slight decrease with time in the anode, and an initial decrease followed by flatness, and then a sharp decrease after 1800 hours in the matrix layer; the electrolyte loss measurement values have remained nearly constant for 25 hours to 1800 hours, but increased sharply thereafter; and the electrolyte loss in this single cell due to pore capacity decrease in pores as power generating parts with diameters smaller than 2 {mu}m was explained quantitatively by a new electrolyte loss mechanism. 11 refs., 6 figs.

  18. Fiscal 1997 development of fuel cell power generation technology. Part 3. Supplementary explanation to R and D of molten carbonate fuel cell and power generation system; 1997 nendo nenryo denchi hatsuden gijutsu kaihatsu hosoku setsumeisho. 3. Yoyu tansan'engata nenryo denchi (hatsuden system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-05-01

    A supplementary explanation was compiled for the results of a commissioned project reported in fiscal 1997 (development of fuel cell power generation technology, and R and D (3) of molten carbonate fuel cell and power generation system). The supplementary explanation was given on the development of parallel flow stack, design/manufacturing of 250 kW stacks, design and manufacturing of 250 kW stacks in connection with installation/adjustment. (NEDO)

  19. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

  20. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

  1. NEDO Forum 2001. Session on hydrogen/PEFC (Toward realization of hydrogen/fuel cell society); NEDO Forum 2001. Suiso PEFC session (suiso nenryo denchi shakai no jitsugen ni mukete)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Introduced in a lecture entitled 'March toward hydrogen/fuel cell society' were NEDO's PEFC (polymer electrolyte fuel cell) related project of its hydrogen energy technology development office and the WE-NET (World Energy Network) hydrogen program. Reported in a lecture entitled 'Toward the practical application of PEFC' were Yamanashi University Clean Energy Center's achievements in the study of polymer electrolyte film, electrodes and separators for PEFC, removal of carbon monoxide by selective oxidation, and so forth. Discussed in a lecture entitled 'Development of high efficiency energy system technologies for transportation and residential/commercial sectors' were the development of a hydrogen-fueled 1kW stack and the result of efforts to develop element technologies for power generation systems fueled by natural gas, methanol, etc. Explained also were the outline and the progress of the project in relation with the fuel cell popularization infrastructure construction project and the fiscal 2001 research and development and the future outlook in relation with the 2nd-phase technology development for WE-NET. (NEDO)

  2. Simulation of PV/FC power hybrid system. Change of system capacity with load form factor; Taiyoko hatsuden nenryo denchi hybrid system no simulation. Fuka keijoritsu ni yoru system yoryo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Sekiguchi, N.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Study is conducted of a photovoltaic/fuel-cell hybrid system whose power storage is a hydrogen storage that uses a hydrogen absorbing alloy. In a simulation in this research, the solar cell conversion efficiency is changed from 15.0% to 21.0% and the fuel cell power conversion efficiency from 40.0% to 50.0%, and the resultant changes in the capacity and operation rate are investigated for each of the devices in the system. The findings follow. A 1.0% change in the solar cell conversion efficiency results in a 4.8kW change in the solar cell capacity and a 1.6-ton change in the hydrogen storage capacity. With a 1.0% change in the fuel cell power conversion efficiency, there is a 14.7kW change in the solar cell capacity and a 5.3-ton change in the hydrogen storage capacity. The fuel cell capacity is not dependent on the solar cell conversion efficiency or fuel cell power conversion efficiency but on the maximum load in each of the load form factors. The rate of occurrence of an operation rate of less than 30% is 54.7% both in DC/DC converter and hydrogen generator, 24.6% in fuel cells, and 16.7% in the DC/DC inverter. 7 refs., 7 figs., 1 tab.

  3. Fiscal 1999 research cooperation project. Research cooperation on community-oriented practical photovoltaic power systems (Practical methane gas fermentation fuel cell power systems); 1999 nendo metan hakko gas nenryo denchi hatsuden system no jitsuyoka ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report describes the research cooperation with developing countries on practical methane gas fermentation fuel cell power systems in 1999-2002. This research aims to construct the methane gas fermentation fuel cell power facility using livestock excreta which can supply power to the facility and peripheral areas. The facility controls various substance concentrations in waste water within environmental standards, and uses waste as compost. This project is very promising in use of environment-friendly energy, effective use of unused energy and power supply to unelectrified areas for China under serious conditions such as rapid increase in energy demand and various environment problems. There are such various issues to achieve this target as securing livestock (pig breeders) and excreta, and fermentation and recovery of suitable methane gas necessary for fuel cell power systems from excreta. This report is composed of 2 parts, (1) Current use of energy resources and use of unused energy in Guangdong province, and (2) Technical requirements for practical methane gas fermentation fuel cell power systems. (NEDO)

  4. FY 1998 annual report on the conversion of fuel at Igumnovskaya thermal power plant; Igumnovskaya hatsudensho nenryo tenkan 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As part of the industrially advanced countries' joint action on the basis of the United Nations Framework Convention on Climate Change (UNFCCC), a thermal power plant in Igumnovskaya (I-plant), Russia was selected as the candidate for rationalization by conversion of fuel from coal to natural gas and introduction of combined-cycle generation, for investigation of the effect on reduction of greenhouse gas generation. The I-plant is located in one of the Russia's largest chemical industry regions, supplying power and steam to the factories in the region. The draft rationalization plan adopts a combination of a coal-fired 300,000 kWh plant that has not been completed and obsolete facilities in the I-plant as the reference case. The plan is drafted to construct a 450,000 kWh combined cycle unit and 3-200 t/h boilers, while effectively utilizing the existing facilities. It requires an investment of US$340 million. The construction works are scheduled to start in 2002 for the initial start-up in 2004. It is expected to reduce CO2 emissions by 1.8 million tons a year and cumulatively 52.7 million tons in the 30-year period from 2005. (NEDO)

  5. FY 1998 annual report on the conversion of fuel at Igumnovskaya thermal power plant; Igumnovskaya hatsudensho nenryo tenkan 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As part of the industrially advanced countries' joint action on the basis of the United Nations Framework Convention on Climate Change (UNFCCC), a thermal power plant in Igumnovskaya (I-plant), Russia was selected as the candidate for rationalization by conversion of fuel from coal to natural gas and introduction of combined-cycle generation, for investigation of the effect on reduction of greenhouse gas generation. The I-plant is located in one of the Russia's largest chemical industry regions, supplying power and steam to the factories in the region. The draft rationalization plan adopts a combination of a coal-fired 300,000 kWh plant that has not been completed and obsolete facilities in the I-plant as the reference case. The plan is drafted to construct a 450,000 kWh combined cycle unit and 3-200 t/h boilers, while effectively utilizing the existing facilities. It requires an investment of US$340 million. The construction works are scheduled to start in 2002 for the initial start-up in 2004. It is expected to reduce CO2 emissions by 1.8 million tons a year and cumulatively 52.7 million tons in the 30-year period from 2005. (NEDO)

  6. Research report for fiscal 1998. Research into the trends of low-carbon automotive fuel manufacturing technologies; 1998 nendo jidoshayo teitanso nenryo no seizo gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Studies are made of optimum materials and methods for manufacturing low-carbon fuels for reduction in greenhouse gas emissions. When their thermal dynamic limits and the technological maturity are considered, it is inferred that no extensive improvement will be achieved by merely improving on the efficiency of the existing fuels. The use of various high-efficiency driving power sources utterly different in mechanism from the conventional ones, such as those for fuel cell-powered automobiles, and the promotion of the use of low-carbon fuels such as methanol and methane for all kinds of driving power sources including those for the said fuel cell-powered automobiles, will become necessary. The use will also be necessary of recyclable materials. The biomass resources, in particular, since they absorb CO2 gas in their growing process by virtue of photosynthesis, may be said to be free of CO2 gas emissions. They have their own problems, however, which involve the economy of energy consumed for their production, harvesting, transportation, and conversion into fuels. It is therefore required that their whole life cycle be studied before their greenhouse gas reduction effect may be correctly assessed. The quantities of resources available for the production of automotive low-carbon fuels, manufacturing technologies, etc., are first of all put in order for easy perusal. An effective way is assessed for the whole including the life cycle. (NEDO)

  7. Fiscal 1997 survey report. Basic survey on trends of waste use type production facilities and waste fuel production facilities; 1997 nendo chosa hokokusho. Haikibutsu riyogata seizo shisetsu oyobi haikibutsu nenryo seizo shisetsu doko kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This survey was made to obtain the basic data for future spread and promotion of No.6 type (waste use type production facilities) and No.7 type (waste fuel production facilities) which were added to the objects having been subsidized since fiscal 1997 under `the environmental harmony type energy community project.` In the former, the kiln in the cement industry and the blast furnace in the steel industry can be extremely large places to receive waste plastic since the facilities are distributed in every area and the treatment capacity is large. However, the effective collection, transportation and sorting of large quantity of waste plastic, especially the problem of removal of vinyl chloride, is a big bottleneck. As to the use of waste plastic using gasification technology, there are no actual results on the commercial basis. That is, however, appropriate for treatment of the waste difficult in treatment, and can be expected of the usage in the chemical industry. In the latter, in the facilities using industrial waste raw materials as fuel, solidification and liquefaction are both operated on a commercial basis. In relation to the solidification and use as fuel of general waste, the treatment of combustion ash is preventing the expansion of use of waste in the industrial field because of a large quantity of chlorine included in the products. 92 refs., 54 figs., 35 tabs.

  8. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Development for practical application of a new production process); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Shinseizo process jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The research and development aims to establish, through verification tests, practical application technologies for two methods, namely, a 'low-temperature liquid phase method' by which cost will be reduced thanks to simplified plant facilities and a 'vapor phase fluidized bed method' in which a composite reforming process may be combined for better economics of scale with a vapor phase fluidized methanol synthesizing method whose facilities may be built to be very large. For the former method, development efforts are made to enable catalyst performance characterization and low-temperature liquid phase methanol production using a small pyrolysis reactor. In the research on pyrolysis reaction, a Raney copper/KOMe/MeOH-based catalyst is used, and this attains a raw material gas conversion efficiency of 92.7%. In the construction of a low temperature liquid phase process, it is found that a single spun conversion efficiency of not less than 90% may be achieved using a heterogeneous catalyst. For the latter method, studies are conducted for the development of, and for the establishment of technologies for designing, synthetic gas production technologies in the development of a heat exchanger type composite reforming furnace and a fluidized bed methanol production process, the development of a catalyst manufacturing technology for fluidized bed practical application, the development of a fluidized bed methanol production technology, and the optimization of the process and its economic efficiency. (NEDO)

  9. Achievement report for 1st phase (fiscal 1974-80) Sunshine Program research and development - Hydrogen energy. Research on hydrogen-fueled engine; 1974-1980 nendo suiso energy seika hokokusho. Suiso nenryo gendoki no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    The research aims to acquire data necessary for designing an engine, which is fueled by hydrogen stored in metal hydrides, for an automobile power plant. It covers the characteristics of hydrogen and their theoretical examination, basic studies on the turbulent mixing and combustion of hydrogen, research using a single-cylinder engine, changes brought into engine performance upon addition of hydrogen, etc. When hydrogen is burned in a spark ignition engine, flashback to the induction system is prone to occur. But this is prevented by directly injecting nothing but hydrogen into the cylinder. In the case of hydrogen fuel, there is the problem of thermal NO generation. Since a hydrogen/air flame is higher in temperature than flames in the case of other fuels, it generates more NO. As techniques for lowering the flame temperature, there are lean fuel combustion, water vapor injection, delayed ignition timing, etc. For the improvement of power and performance, increasing the engine revolution and pressurizing the inlet air are the methods, but both have their own shortcomings. An engine equipped with a third valve is experimentally constructed in this research, which is theoretically free of flashback, suppresses a reduction in the inlet air volume, and necessitates no high-pressure injection system. (NEDO)

  10. Report for fiscal 1998 on results of research and development of silicon-based polymeric material. Material research for the liquid methane fueled aircraft engine; 1998 nendo keisokei kobunshi zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was conducted for the purpose of establishing basic technology concerning molecular design, synthesis, material formation, and evaluation of silicon-based polymers which are expected to provide superior electronic/optical functions, high heat/combustion resistance and dynamic properties. The research subjects were such as following: research and development of silicon-based polymeric materials with sea-island microstructures; research and development of silicon-based polymeric materials with sea-island microstructures; research and development on IPN formation with silicon-based polymers; research and development of hybrid silicon polymers with organometallic compounds; research and development of silicon containing polymer materials with ring structures; general committee for investigation and research; the optimized low-temperature Wurtz synthesis and modification of polysilanes; study of unsaturated and hypercoordinate organosilicon compounds; basic studies on the synthesis and properties of silicon-based high polymers; studies of new monomer-synthesis and their polymerization reaction; studies on new method of preparation and functionalization of polysilanes; novel applications of silicon-based polymers in imaging devices for information display, memory, and recordings; and molecular design of silicon-containing {pi}-conjugated and {sigma}-conjugated compounds. (NEDO)

  11. FY 2000 report on research and development of combustion technology utilizing microgravity conditions for fuel diversification; 2000 nendo bisho juryoku kankyo wo riyoshita nenryo tayoka nensho gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at development of optimum combustion technology with diversified fuels, e.g., naphtha and LCO, for gas turbines and others as power sources for topographical energy supply. The combustion under the microgravity is also investigated using the underground facilities at Japan Microgravity Center. Described herein are the FY 2000 results. For construction of combustion model and simulation, the combustion reactions for various liquid fuels are simplified to calculate ignition delay, adiabatic flame temperature and laminar burning velocity with an error less than about 3%. The microgravity combustion experiments are conducted for spray dispersed into a cylinder, to find flame propagation velocities changing with the vaporization characteristics of liquid fuels, and also to construct the combustion models. The premixed turbulent combustion simulation program is developed using a probability density function and analyzed. Development of new combustion technologies includes the study themes of flame propagation and combustion of the air mixture of the multi-component fuel in which the spray exists, combustion characteristics of the droplets of diversified fuels, and combustion of gas turbines with diversified fuels. A propane/air mixture shows different flame propagation characteristics whether it contains kerosene or LCO droplets. The effects of electrical field intensity in the combustion zone on combustion of fuel droplets are elucidated. (NEDO)

  12. Report on the survey of the commercialization of wood biomass energy. Project on the production of wood pellet fuel; 2001 nendo mokushitsu baiomasu energy jigyoka chosa hokokusho. Mokushitsu peretto nenryo seizo jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For the purpose of regenerating forestry and contributing to the policy for prevention of global warming, a potential study was made of the commercialization of the wood pellet using low-quality wood materials such as thinnings and wood pieces from lumber mill. In the study, based on the survey of raw materials of wood pellet and the demand amount, the scale of pellet production was assumed, and subjects were arranged toward the basic design of plant, evaluation of economical efficiency and commercialization. As a result of the study, the following subjects were extracted. In the study, the supply of lumbers of 2,800 t/y and securing of demand of about 1,600 t/y were set forth as a premise, but the subject was to secure the initial demand. The pellet combustor was higher in price than the kerosene combustor, and for the imported combustion equipment, the combustion of white pellet was supposed. It is necessary to develop combustor of pellets including the bark. In the trial calculation of the unit price of heat utilization (yen/Mcal), the pellet stove was about 3.3 times as high in price as the kerosene stove. It is necessary to reduce the pellet price down to 30 yen/kg or so by decreasing the cost of pellet production. (NEDO)

  13. Fiscal 1993 achievement report on next-generation industrial structure technology (Advanced materials for extreme environments - Development of methane fueled aeroengine); 1993 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Efforts were exerted to develop advanced materials for use under extreme environments, which were intermetallic compounds and fiber reinforced intermetallic compound composite materials excellent in heat resistance, specific strength, oxidation resistance, or the like. For the development of intermetallic compounds, efforts were made to develop Ti-Al-X (X=metal) high specific strength intermetallic compounds and Nb-Al-X (X=metal) high melting point intermetallic compounds. Ternary phase diagrams were prepared and the effect of added elements on basic characteristics was investigated. Basics of element technologies (texture control, melting, casting, and isothermal rolling) for manufacturing panel materials were studied and, in the case of Ti-Al-X systems, Ti-Al thin panels were fabricated. In the case of Nb-Al-X systems, items were experimentally fabricated by casting in an effort to study precision casting technology optimization. For the development of composite materials, efforts were made to develop SiC based and SiMC (M=metal) based fibers, and studies were carried out to complex them with Ti-Al based matrices. (NEDO)

  14. FY 1999 report on the model project on the effective utilization of waste-base biomass fuels. Basic survey for the feasibility; 1999 nendo haikibutsukei biomass nenryo yuko riyo model jigyo jisshi kanosei kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Survey on the waste biomass was conducted for Thailand, Malaysia, Indonesia, Vietnam, Laos, Nepal, Butan, Myanmar and Cambodia to study feasibility of the project for the concrete utilization of biomass resources. In Thailand, it is expected to construct large-scale model plants for biomass resources such as rice hulls, bagasse, wood waste and oil palm. In Malaysia, expected are the cogeneration at 5MW class palm oil plant, large-scale power plant using wood waste, plant using the biomass from waste palm oil, etc. In Indonesia, there is a great potentiality, but it is necessary to handle it carefully in consideration of the unstable situation of the society. In Vietnam, the detailed survey of feasibility is needed on the project for efficiency heightening at state-run plants, the assumed national plants (recommended by the government), etc. In Laos, small-scale power generation using the forestry waste such as sawdust is expected. (NEDO)

  15. Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 6. Development of fuel cell of pure hydrogen fueled solid polymer type; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 6. Junsuiso kyokyu kotai kobunshigata nenryo denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for research and development Task-6. The objective is to verify performance and reliability, by means of field tests, of a power generation plant using fuel cells of pure hydrogen fueled solid polymer type with power transmission terminal efficiency of 45% and output of 30 kW. The fuel cells were developed by using the cathode humidification process as a humidification method suitable for operation at high utilization rates. With a three-cell stack made by using this humidification process (having an effective area of 289 cm{sup 2}), verification was made on the current density of 0.2A/cm{sup 2}, the characteristics of 0.75V or higher, and the uniform voltage distribution performance being the immediate targets. In order to mitigate the hydrogen utilization in the fuel cells, discussions were given on the serial flow system that divides the laminated cells into two blocks. Thus, operation was found possible with the utilization rate in each block reduced to about 80% by selecting an adequate division rate even if the hydrogen utilization rate is 96% in the entire stack. Stable operation has been performed in the 5-kW class power generation test using the cathode interior humidifying system. Specifications for 30-kW class power plant, system configuration, safety, and material balance were discussed. The basic design was made on the hydrogen gas humidity adjusting system. (NEDO)

  16. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of application type novel-structure thin-film solar cell manufacturing technology - Development of static micro-concentrator solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An acorn type concentrator is a 2-dimensional system and realizes relatively high magnification power, but it requires a special assembly process for modularization because the cells and the concentration system are quite small. Under the circumstances, studies are conducted on a prism array concentrator (PAC) which will demand a smaller burden for modularization. A PAC system is basically a 1-dimensional concentrator in terms of light collection performance. The cell to be attached to one plane in the longitudinal direction of the long triangular prism is so small as 5mm in width, yet it may be as long as 50-100mm, and the conventional flat plate assembly process may be made use of. A concentration efficiency of 82% and a conversion efficiency of 10.9% were obtained from a minimodule with a light intercepting area of 5cm times 4cm. Furthermore, a conversion efficiency of 19.7-21.4% was obtained when a small 5mm-wide cell applicable to a PAC type concentration was used. Since a prism type concentrator optical system will cost much for its molding and strengthening when it is built of glass, inexpensive EVA (ethylene-vinyl acetate copolymer) was utilized as an adhesive filler. (NEDO)

  17. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of solar cell evaluation system (Survey of research and development of solar cell evaluation system); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi hyoka system no kenkyu kaihatsu (taiyo denchi hyoka system no kenkyu kaihatsu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The fiscal 1999 results of survey and research conducted for the establishment of solar cell performance evaluation and reliability evaluation methods are reported. In the development of a super high fidelity (broad spectrum) solar simulator for cell evaluation, a prototype was tested for performance evaluation, and initially set values were achieved. In the development of a large-area module evaluation technology, the radiation area was increased to be 1.0m times 1.0m large. Outdoor exposure tests continued at 5 sites in Japan, 3 sites in Australia, and 1 site in Oman, and analyses and databasing were carried out for the outputs of various types of solar cell modules. As for the problem of coloring of fillers which are module constituents, coloring in the U.S. was attributed to high temperature and intensive insolation, and in Austria to an oxidation inhibitor. In the development of a photo-accelerated degradation testing method for Si-based solar cells, application of the cycled illumination test was found feasible. In this test method, an amorphous silicon solar cell retains 70% of the initial Pmax value even after the passage of a period equivalent to 30 years. (NEDO)

  18. Report on commissioned business for fiscal 1997. Development of new power storage system for cells and development of technology for distributed power storage (research for a zinc/air cell system for automobiles); 1997 nendo itaku gyomu hokokusho. Shingata denchi denryoku chozo system kaihatsu bunsangata denryoku chozo gijutsu kaihatsu (denki jidoshayo aen kuki denchi system chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Concerning the above, it is discussed whether such a system is feasible in Japan. A zinc/air cell system requires some special plants for zinc regeneration, etc. It is necessary to build a zinc refining plant and to install dozens of electrode replacing facilities in an area dozens of kilometers in diameter with the plant at the center. For such a system to be functional, there have to be several tens of thousands of automobile users in a limited area. In Japan, so large a number will not be found anywhere even if the appeal is directed to those in the postal service and electric utilities. There will be no economic success in Japan, different from in Germany. As for the economic comparison between a zinc/air cell system and natural gas system, the two will be equivalent to each other as far as the use of the quick filling stations for the natural gas automobiles remains as it is. When the number in consideration is so large as several tens of thousands, however, the natural gas system will turn out to be economically superior to the zinc/air cell system. 19 figs., 29 tabs.

  19. Fiscal 2000 survey report. Development of novel battery power storage system (Development of distributed power storage technology - Marketability of lithium storage battery); 2000 nendo gyomu hokokusho. Shingata denchi denryoku chozo system kaihatsu - Bunsangata denryoku chozo gijutsu kaihatu (Ritium niji denchi no shijosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey is conducted of the current status of storage batteries and the marketability of the lithium ion battery. In the study of future marketability of storage batteries for electric vehicles, the small vehicle Hypermini currently loaded with a lithium ion battery is taken up and it is assumed that each carries a 10 kWh battery, and then it is estimated that there will be an approximately 2200 times 10{sup 3} kWh market in Japan in 2020. As for hybrid vehicles each loaded with a 1 kWh battery, it is estimated that 3997 times 10{sup 3} kWh will be on the market in 2020. For the fuel cell powered vehicle, similarly, there will be approximately 2,500 times 10{sup 3} kWh on the market in 2020. As for power storage facilities for power load shaving, the demand for cells in 2020 is estimated at 1,032-3,924 times 10{sup 3} kWh on the assumption that they operate 4 hours in the daytime. As for the uninterruptible power supply, it is estimated that 800 times 10{sup 3} kWh will be required by those installed at data centers in 2020. It is also estimated that 252 times 10{sup 3} kWh will be necessary in the form of storage batteries for motored wheelchairs in 2020. As for distributed power source systems such as those dealing with wind power or photovoltaic power, there are a number of technical problems that have to be settled. (NEDO)

  20. Achievement report on Sunshine Program research and development for fiscal 1981. Research and development of amorphous solar cells (Research and development of integrated type amorphous solar cells); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Shusekigata amorphous taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    An a-SiC (amorphous SiC) material with a wider band gap adds to the conventional hydrogen- and fluorine-based a-Si materials in the study for device efficiency enhancement, and the a-SiC is found suitable as a wide-gap window material. The separated formation technique is found to work effectively for improvement on cell characteristics because it prevents the mixing of impurities of different types. A p-i-n (positive-intrinsic-negative) type amorphous solar cell is subjected to analysis, and a theoretical efficiency of 12.5% is obtained in photoelectric conversion. A conversion efficiency not less than 7% is obtained from an ITO (indium-tin oxide)/p(SiC)-i-n/Al cell on a glass substrate. Design is optimized for area enlargement for an integrated type device, which results in an experimental 10cm-square integrated type solar cell with a conversion efficiency of not less than 5%. As for modularization, a glass substrate for integrated type device is used, as is, as a light-receiving surface protecting board, and studies are conducted thereon. It is then found that the amorphous solar cell experiences some degradation in reliability at the beginning of an irradiation test but that no extensive degradation in reliability is observed even after the passage of 1,000 hours from the beginning of the test. The separated formation technique is found suitable for use in mass production. (NEDO)

  1. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research and development of technologies for enlarging amorphous solar cell area); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (amorphous taiyo denchi no daimensekika gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In the basic studies of large-area a-Si film formation technologies, the validity is discussed of the evaluation technique using plasma optical emissions spectrometry (OES) employed for the achievement of the intended film qualities. The film forming condition that exerts the greatest influence on the plasma state relative to OES is the power of discharge, and correlations are found to exist between specific emission intensity, infrared absorption level, and photoconductivity of the film. It is found that a P- or B-doped Si:H/SiC:H film is suitable as the material for the window layer on the light-receiving surface of the solar cell. Materials are studied for the i-layer responsible for photo carrier generation, isolation, and acceleration. Studies are also conducted on fluorine-containing film. In the efforts at designing and building solar cells, ITO (indium-tin oxide)/n-i-p/SS (reversed type) cells are analyzed, designing is carried out for transparent electrode film thickness optimization, window effect in stainless substrate cells is improved, glass substrate cells are experimentally built and analyzed, large-area solar cell properties are improved, interaction between the substrate and a-Si is studied, and reliability tests are conducted. For cost reduction, it is necessary to develop technologies of automated production of simplified-structure modules using low-cost materials. Basic matters are taken up for discussion. (NEDO)

  2. Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of amorphous solar cells (Research and development of amorphous solar cells on flexible film substrates); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Kadosei film wo kiban to suru amorphous taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-31

    Efforts will be made to reduce the cost, increase efficiency, and enlarge cell areas and, at the same time, to establish the foundation of a roll-up type solar cell manufacturing process which is required for the implementation of mass production. In an inverted pin/ITO (indium-tin oxide) hetero-face structure cell installed on a polymer film substrate, a conversion efficiency of 5.33% is achieved in the case of a solar cell whose n-layer is of the amorphous phase, and 6.36% in the case of a cell of the microcrystallized phase. A roll-up type glow discharge CVD (chemical vapor deposition) unit is designed and experimentally built, which is for the realization of large area cells. It is now duly expected that an undoped (i-type) a-Si:H film will be deposited to a thickness of approximately 5000A. As the result of a first-step screening conducted in search of amorphous solar cell sealing materials, some applicable plastic materials are selected. The future is bright of amorphous solar cells on polymer film substrates. (NEDO)

  3. Fiscal 1993 achievement report on New Sunshine Program. Development of photovoltaic power generation system practicalization technology (Development of ultrahigh-efficiency solar cell technology - Development of crystalline compound solar cell technology); 1993 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu taiyo denchi no gijutsu kaihatsu (kessho kagobutsu taiyo denchi no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Efforts are made to enhance InGaP cell efficiency (target 16%) on a GaAs substrate by prolonging the InGaP minor carrier life span. In preparation of InGaP cell fabrication on silicon, a study is made of epitaxial growth of a wide band gap layer. By improving on the conditions of InGaP heteroepitaxial growth under the MOCVD (metal-organic chemical vapor deposition) method on a GaAs substrate, the InGaP cell base layer minority carrier life span is increased to be longer than 5ns. The use of epitaxial crystals greatly improves on the efficiency of InGaP cells on a GaAs substrate. Furthermore, cell structure improvement and the like are accomplished, which results in the achievement of an efficiency rate of 17.4%. As a basic technology for the fabrication of InGaP/Si tandem cells, experiments are conducted of growing a wide gap layer for the growth of Ln{sub 1-x}Ga{sub x}P on an silicon substrate. For the evaluation of epitaxial crystals and interfaces, time resolution photoluminescence measurement is performed and the result is compared with the result of simulation. (NEDO)

  4. Fiscal 1999 report. Development of an electric power storage system using new type batteries, and development of a discrete type electric power storage technology (Survey on trend in developing batteries for electric power storage); 1999 nendo shingata denchi denryoku chozo system kaihatsu bunsangata denryoku chozo gijutsu kaihatsu hokokusho. Denryoku chozoyo denchi no kaihatsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Demand is increasing in recent years in Japan on batteries for electric power storage to respond to load variation in electric power supply. If electric power storage batteries are applied for practical use, nighttime excess power can be stored appropriately, which can be discharged during day time when the demand is increased, so that the demand variation can be handled adequately. Secondary batteries, if used, are characterized by having much greater energy density and output density because of storing the electric energy as chemical energy than in pumped-storage power generation which stores the energy as the positional energy of water. Therefore, this paper describes the surveys performed on the trend of developing the power storage batteries inside and outside the country. Section 1 shows the current status of annual load rates in other countries, and the current conception on power storage in these countries. Section 2 states the current status of practical application of power storage batteries having been developed in Germany and the U.S.A. and performed of demonstration tests. Section 3 reports the current status of developing new type power storage batteries. Section 4 describes the current status of developing the power storage batteries for power users. (NEDO)

  5. Fiscal 1976 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cell); 1976 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-05-30

    This report describes the fiscal 1976 research result on new type solar cells for photovoltaic power systems. On junction formation, the solar cell fabricated by spray coating showed output characteristics equivalent to that by rotary coating or phase diffusion, and inexpensive coating liquid, 1/40 of commercially available liquid in price, showed a sufficient result, however, the conversion efficiency of P{sup +}/N elements was insufficient. Schottky barrier polycrystal Si thin film was suitable for large-area elements without any property degradation. Small grain boundary density of polycrystal layers was also necessary. Temperature characteristics of collector element structure with a comb electrode were calculated theoretically. Change in diffusion length of minority carriers due to temperature well agreed between measured and calculated ones. Optimization calculation was also carried out. The size, curve, weight and transmissivity of plastic and glass materials for solar cell packaging were evaluated by continuous outdoor exposure tests. Fluorinated ethylene-propylene, methyl methacrylate and polycarbonate plates and glass were the most promising materials because of less deformation. (NEDO)

  6. Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cells); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-27

    This report summarizes the fiscal 1974 research result on R and D of new type solar cells, which includes researches on (1) solar cell structure, (2) packaging, and (3) improvement of a conversion efficiency. In the 1st research, theoretical study was made on the relation between a solar cell efficiency and various design factors to obtain basic data for ordinary cell structure and vertical junction type cell structure. As impurity source, a thermal diffusion method using doped oxide by CVD was compared with that using boron nitride, resulting in no difference in solar cell characteristics between both methods. The measurement results on contact resistances of Al, Fe and Ni with electrodes prepared by electron beam deposition showed that these materials are applicable to Si more than 10{sup 18}/cm{sup 3} in impurity density as electrode materials. In the 2nd research, exposure tests were made on some kinds of specimens, resulting in no troubles. Study was made on production costs and structures suitable for automatic production of 4 kinds of packages with different basic structures. In the 3rd research, the prototype solar cell was prepared to use under solar radiation within 20SUNS. (NEDO)

  7. FY 1999 report on the verification test on the system interconnection of the photovoltaic power system in Malaysia; 1999 nendo Malaysia ni okeru taiyo denchi hatsuden system no keito renkei jissho shiken seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    JET and SIRIM Behad, which is the standards and industrial research institute in Malaysia, worked this project together, and installed the Photo Voltaic Generation System (hereinafter refferred to as 'PV system') on the roof of the research building for researching basic conditions in the practical use of the PV system by gathering basic data. The power quality of a supply system necessary for a grid connection of the PV system was researched in the evidential experiment. Moreover, the invasion level and the invasion frequency to the PV system of the thunder surge by the peculiar weather condition in this region were researched. In addition, the requisite for the islanding function for the alternative emergency power supply was investigated. The contents of this project were composed of the three items. (1) research of the power quality in low voltage distribution system. Before and after the PV system is connected with the supply system, basic data concerning the power quality of the voltage, the current, and the frequency fluctuation, etc. in the system was collected. (1)measurement and investigation of the power quality under the current low voltage distribution system. By connecting ad monitoring recorder with a lower voltage distribution system, the current power quality i.e. voltage, current, frequency the fluctuation of voltage and frequency at the regular time were measured and investigated. (2) The power quality in the supply system grid connection of the PV system was measured and investigated. The voltage and the frequency in the case of supply system grid connection of the PV system were compared with the current state of preceding clause 1 and the stability of the power quality was evaluated. Moreover the output power of the solar battery was connected with the measurement device and then the surface temperature of the solar battery module, DC voltage, current and quality of solar radiation were measured. The subject in the practical use of the PV system in Malaysia was extracted through these experiments. (2) Research of level and frequency of the thunder surge. 1. Measurement of level and frequency of the thunder surge by the thunder surge counter. The thunder surge counter was set up respectively on the positive line and the negative line of the solar battery. These signals are taken into the memory of the thunder surge counter, and the level and the frequency data of the thunder surge which invade the PV system were accumulated. 2. Evaluation by simulation. The PV system was evaluated to the thunder surge obtained in preceding clause 1 by the simulation. In addition the simulation analysis was conducted by the system equivalent circuit on the assumption of the thunder surge current at the location of the system. (3) Research of the islanding function of the PV system as the backup power supply was evaluated when blacking out. (NEDO)

  8. Solar cell. Taiyo denchi

    Energy Technology Data Exchange (ETDEWEB)

    Kamihara, T; Kondo, S; Mori, K [Matsushita Electric Industrial Co. Ltd., Osaka (Japan)

    1990-10-23

    This invention provides a solar cell having high resistance to strong incident light and high temperature preservability. Reason of performance degradation of the solar cell in high temperature atmosphere thermally diffuses at the boundary surface of the silicon with metal particles. The method of blocking this thermal diffusion is that the film thickness is of the level that the electrons can pass through the film by a quantum dynamical tunnel effect. In this invention, the construction is that a transparent substrate, a transparent electrode, a P-type amorphous silicon, an I-type amorphous silicon, silica and a collector electrode are sequentially laminated and receives the incident light, thus generating a voltage between the two electrodes. Thickness of silica film is 10-100 microns. Materials of the collector electrode are either single element or alloys of Cs, K, Na, Li, Ba, Mg, Cd, Ta, Al, Mo, Zr, Co, Fe, Cu, Ag, W, Cr, Au and Ni. 13 figs., 1 tab.

  9. Solar cell. Taiyo denchi

    Energy Technology Data Exchange (ETDEWEB)

    Amemiya, S.; Hashimoto, Y. (Canon Inc., Tokyo (Japan))

    1991-05-17

    This invention provides a cheap solar cell having a transparent surface protective layer which satisfies both controversial properties such as high electroconductivity and high water repellency and also abated the reduction of photoelectric conversion. In other words, this invention provides a solar cell having a surface-protective layer prepared by lamination of a mixture of a transparent water-repelling resin and a transparent electroconductive oxide powder; said protective layer is grounded at the surface resistance of 1 {times} 10 {sup 10} ohm or less and the contact angle of water on said protective layer is 90 degrees or more. The transparent water-repelling resin used is a fliorine resin such as PTFE and a silicone resin such as organopolysiloxane. The transparent electrodonductive oxide powder used is tin oxide, indium oxide or a complex compound of ton oxide and antimony oxide. The solar cell of this invention can be used for a long time because the adhesion of the dusts and the contamination by dirty water are restricted. 1 fig., 1 tab.

  10. Fiscal 1993 international research cooperation project. Feasibility study of finding out the seeds of international joint research (technology for environmental preservation using biotechnology, technology for effective use unused hydrocarbon resource, technology of solid electrolyte fuel cells for high-efficient electric vehicles); 1993 nendo kokusai kenkyu kyoryoku jigyo. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa (biotechnology ni yoru kankyo taisaku gijutsu, miriyo tanka suiso shigen no yuko riyo gijutsu, kokoritsu denki jidosha no kotai denkaishitsu nenryo denchi gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is aimed at internationally cooperating in the R and D of industrial technology and improving industrial technology of Japan. For it, the following three technologies were investigated: 1) environmental preservation technology using biotechnology, 2) technology for effective use of unused hydrocarbon resource, 3) solid electrolyte fuel cell (SOFC) technology for high-efficient electric vehicles. In 1), bio-remediation is a choice as the result of trially using technologies for remediation of the environment polluted by pollutant, but it is not a technically completed one, but one which will be improved by trial and error. By the application of gene engineering, the use of gene recombination enables wide spread of decomposition genes. In 2), technical subjects were studied such as superheavy distillate, oil shale, coalhead methane and methane hydrate. In 3), designed were cylinder type and planar type SOFC of 850degC operation and 10kW output. Accumulation and weight of a total SOFC system are 81 liters and 100 kg in cylinder type and 136 liters and 200 kg in planar type. The vehicle can be equipped with the SOFC. 171 refs., 72 figs., 54 tabs.

  11. FY 1999 Report on results of development of high-efficiency energy system technologies for transportation and domestic use. R and D of polymer electrolyte fuel cells, power system technologies, and several kW class domestic power systems operating at normal pressure; 1999 nendo un'yu minseiyo kokoritsu energy system gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, joatsu sadogata su kW kyu kateiyo dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Described herein are the FY 1999 results of the research and development project aimed at development of fuel cell systems for power source systems suitable for domestic use. The programs for development of fuel cell body include improvement of the anode forming method for increasing its CO tolerance, enhancing cell performance at 0.5mg-metal/cm{sup 2} as the catalyst quantity to a level almost comparable to that obtainable at 0.9mg-metal/cm{sup 2}. The programs for development of the fuel supply system include studies on endurance of the elements, e.g., starting-up/shutting-down of the Ru/Al{sub 2}O{sub 3} catalyst, using a microreactor, confirming that it is serviceable for at least 1,000 hours. The natural gas reformer is developed and operated, on a trial basis, achieving stable supply of steam and fuel, and thermal efficiency of 82.7%. The operation researches include development and operation of a 1kW class module, achieving the performance surpassing the FY 1999 targets (average cell voltage: 0.70V, output: 1.27kW) with a simulated reformate gas at an air utilization rate of 20% and current density of 0.3A/cm{sup 2}. (NEDO)

  12. FY 2000 research cooperation project on the research cooperation for the commercialization of the regional adaptation type photovoltaic power generation system, etc. Research cooperation for the commercialization of the methane fermentation gas fuel cell power generation system; 2000 nendo kenkyu kyoryoku jigyo. Chiiki tekigogata taiyoko hatsuden system to no jitsuyoka ni kansuru kenkyu kyoryoku (Metan hakko gas nenryo denchi hatsuden system no jitsuyoka ni kansuru kenkyu kyoryoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research cooperation for the commercialization of methane fermentation gas fuel cell power generation system was made in a stock farm in Guangzhou city, China, and the FY 2000 results were summed up. In the project, the methane fermentation gas is recovered from animal faces, and a power generation system by fuel cell using the gas as fuel is constructed, and at the same time the waste is made compost and used as manure. In this fiscal year, the starting ceremony was made at the stock farm in Guangzhou city in June, and the main body of fuel cells was carried in and assembled. The trial operation of the system was successfully made in March 2001. At the same time, survey of the waste water from the farm and methane fermentation was made with accuracy. Survey was further made of the actual state of the recent energy supply/demand and the present situation of renewable energy as measures taken for non-electrification areas and environmental problems. As a result, the importance of further cooperation with the China side was emphasized in terms of the securing of animals/faces, optimum methane fermentation/recovery from animal faces, optimization of electric power of the area and environmental response, etc. (NEDO)

  13. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research on practical application of set solar cell); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shisshiki taiyo denchi jitsuyoka kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Possibility of practical application of dye-sensitized solar cells (Graezel cells) is discussed. Fine titania particle preparation conditions and titania thin-film electrodes were optimized and an energy conversion efficiency of 7.7% was accomplished. The screen printing method was applied to the manufacture of dye-sensitized electrodes, and performance governing factors were grasped. The use of the screen printing method resulted in a conversion efficiency of 6-8.4% when the factors were optimized. Though lower than the 10% in the Graezel report, values near that were obtained. The status of latest research and development is compiled involving studies about electron transfer dynamics in dye-sensitized solar cells, manufacture of sensitizing dyes and mesoscopic metal oxide thin-film, electron transfer layers and their physical properties, and solidification of hole transfer layers. Research was conducted aiming at their practical application, and tasks and problems in each of the said items were point out. A logical approach to achieve high conversion efficiency was deliberated, and studies were made about how to propel forward endeavors involving design guidelines for high-performance sensitizing dyes, design and preparation guidelines for thin film for electrodes, analysis of stability, solidification of the redox electrolyte, etc. (NEDO)

  14. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of high-reliability CdS/CdTe solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Cost reduction for the above-named solar cells is the aim of this effort. On the basis of the results of past studies, a technology is established of fabricating a thin CdS film by subjecting a CdS film to organometal pyrolysis, and this brings about a decrease in photoabsorption loss in the range of waves shorter than 500nm and a decrease in in-film reflection loss for an increase in short-circuit current density. A proximity sublimation method is used for CdTe film fabrication, which improves on film quality and film adhesion. These efforts result in the achievement of a conversion efficiency of 16.0% which is the highest in the world. Studies are promoted in a process nearer to the ultimate form, and a 30cm times 60cm large CdTe solar cell is fabricated on the basis of a patterning technique, and the product attains a conversion efficiency of 9.8%. In fiscal 1998, studies center about the establishment of a film fabrication process for a medium-are substrate and about the enhancement of its conversion efficiency, and facilities capable of dealing with large-area substrates are introduced and operated. In a typical achievement, a CdTe solar cell is experimentally fabricated in a process which is wholly under normal pressure, and the product with an aperture area of 1376cm{sup 2} exhibits a conversion efficiency of 10.5% according to JQA (Japan Quality Assurance Organization). (NEDO)

  15. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of environmental adaptation of next-generation solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - jisedai taiyo denchi kaihatsu kankyo tekioka chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys are conducted of photovoltaic power system development projects and their utilization in Japan and overseas, and a discussion is made on the progress, technical challenges, effects, and implementation systems relating to the solar cell application technology development project under the New Sunshine Program. Compiled in the report are the results of surveys of the research and development of photovoltaic power systems and their diffusion in the U.S. and European nations, and the research and development strategies for and the trends of the development of various types of solar cells in these countries. The trends of research and development of non-conventional type solar cells are also collected, which include 3 cases of TPV (thermophotovoltaic) devices, 5 cases of new inorganic materials, 1 case of new organic materials, and 4 cases of dye-sensitized solar cells. In relation to the status of resources of crystalline compound-based solar cell materials, raw materials for solar cells other than silicon are taken up, and their reserves, manufacturing methods, quantities yielded and consumed, costs, etc., are surveyed. These are all taken into consideration in discussing the basic approach to the study of future research and development as it ought to be. (NEDO)

  16. FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for production of thin-film solar cells and low-cost, large-area modules (Development of technologies for high-reliability CdTe solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is implemented for production of low-cost, large-area modules of CdTe solar cells by the high-quality film-making process and high-function patterning, and the FY 1999 results are reported. The research program for the large-area TCO film-making technologies involves investigations on improvement of SnO{sub 2} film quality by the mist method and continuous film-making, which lead to continuous, stable production of 34 substrates of low resistance of 9.7{omega} on the average. The program for production of the large-area, thin-film CdS/CdTe solar cells involves production of TCO and CdS by the mist method, and patterning of the laminated TCO/CdS film by laser scribing. The CdTe film is formed by the atmospheric pressure CSS method, and treated with CdCl{sub 2} to improve its crystallinity. The CdTe film is patterned by sand blasting, and provided with the carbon and silver electrodes by screen printing, to complete the cell. The process is totally effected at the atmospheric pressure, needing no vacuum device. The CdTe solar cell assembly (130 cells connected in series, opening area: 5,413cm{sup 2}), fabricated on a trial basis, achieves a conversion efficiency of 10%. (NEDO)

  17. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of novel voltaic cell structure solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The present state and trend are surveyed of organic ferroelectric thin films, new carbon materials, fullerene compounds, and thermophotovoltaic (TPV) power. In the study of organic ferroelectric thin-film solar cells, the effort still remains at the basic stage, with the conversion rate as low as 3% in Europe and 2% in Japan. The progress of basic studies, however, is worth attention. It is deemed that 15% is the photoconversion rate to be currently expected from new carbon material solar cells. Fullerene compounds include some semiconductors whose bandgap values may be controlled across a 0.75-1.95eV range, and they may find their place in thin-film solar cells. However, their physical properties are not fully known, and their development into devices such as solar cells is scarcely reported. The research and development of TPV in the U.S. is led by NASA (National Aeronautics and Space Administration) and NREL (National Renewable Energy Laboratory), with their efforts concentrated on the development of portable power sources utilizing combustion heat. In Europe, TPV application to small-scale residential cogeneration systems is under study. (NEDO)

  18. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost and large-area module manufacturing technologies, and new type amorphous solar cell manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to put amorphous solar cells for power use into practical use, research and development has been performed on a low-cost mass production technology for modules with large area and less deterioration using film substrates. This paper summarizes the achievements in fiscal 1999. In developing an efficiency enhancing technology, development of an a-Si/a-SiGe/a-SiGe triple cell structure was launched, and discussions were given on band gaps, film forming conditions, and film thickness. In developing a film forming speed enhancing technology, systematic experiments were performed, as well as theoretical analysis on the film forming mechanism in the plasma CVD process. In developing the process technology for film substrate solar cells, with regard to an a-Si production device of the multi-chamber arranged stepping roll system, six plasma CVD chambers were increased to 13 chambers to improve the electrode forming speed and such processes as drilling low-cost substrates, and laser patterning. In trial fabrication of a triple cell, a module in which one row of the SCAF cell is laminated provided an initial efficiency of 9.64%. (NEDO)

  19. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Feasibility study of wet-type solar cell commercialization); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu, Shuhen yoso gijutsu ni kansuru chosa kenkyu - Shissiki taiyo denchi jitsuyoka kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Dye-sensitized solar cell commercialization was studied for feasibility. Studies were made about photoelectric conversion efficiency and various factors supposedly to affect the life and other properties, and a wet-type (dye-sensitized type) solar cell was fabricated. In an endurance test, the dye-sensitized solar cell retained its initial performance after 3,500 hours of continuous irradiation. A 16 cm{sup 2}-large integrated type Graetzel cell was fabricated, and it achieved a photoelectric conversion efficiency of 4.6%. Furthermore, in the study of Graetzel cells, possibility of the creation of new electrolytic solutions was discussed, a non-TiO{sub 2} dye-sensitized solar cell was fabricated based on the self-assembled electrodeposition of the ZnO dye, and the feasibility was deliberated of a dye-sensitized solar sell using a composite oxide semiconductor. Concerning their development in the future, it was concluded that dye-sensitized solar cells including the Graetzel cell were equipped with the basic characteristics of a next-generation solar cell that would be requested to be low in cost and high in performance. (NEDO)

  20. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of ultrahigh-efficiency solar cell application fields); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu, Shuhen yoso gijutsu ni kansuru chosa kenkyu (Chokokoritsu taiyo denchi tou oyo bunya kaitaku chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Surveys and studies were conducted in order to make propositions concerning the fields of application wherein the merits of ultrahigh-efficiency solar cells would be fully utilized. A questionnaire was held about solar cell application fields, and studies were made about new systems based on the need in the market for specific solar cell goods and capable of supporting their mass diffusion. Proposed as the result was the establishment of a rental (lease) system for photovoltaic power systems, a local photovoltaics advisory system, a market for used photovoltaic power systems, and so forth. In the feasibility study of photovoltaic power generation on unused land in agricultural villages, surveys were conducted concerning energy problems, the energy structure, the actual state of energy consumption, the abandoned farm and its utilization, and so forth. Propositions involving photovoltaic power feasibility were then made, which covered power consumption for greenhouse culture, energy supply for producing methanol out of biomass, power sources for insect incapacitating yellow fluorescent lamps, power sources for livestock barn air-conditioning, power sources for animal excretion treatment, and so forth. (NEDO)

  1. Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Manufacture of high-reliability CdTe solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The target is a low-cost CdS/CdTe solar cell of a large area (60cm times 90cm), the establishment of mass-production technologies for the cell, and the enhancement of production efficiency. A thin film formation technology of subjecting CdS film organic metal to pyrolysis is established, which reduces photoabsorption loss in the shortwave domain of wavelength of not longer than 500nm, reduces reflection loss in the film, and improves on short-circuit current density. Improvement is also achieved on CdTe film quality and junction quality by use of a proximity sublimation method in a vacuum, when a conversion rate of 16.0% (1cm{sup 2}) is attained which is the highest in the world. Based on the results of the above-said efforts, a 3.3mm-thick glass substrate is employed for CdTe film to develop into a 30cm times 60cm-large size, with the film thereon uniformly thick over a large area thanks to a normal pressure proximity sublimation method. Studies are made toward a process nearer to the ultimate product and, using the patterning technique, a 30cm times 60cm-large CdTe solar cell is tentatively built realizing a conversion rate of 9.8%. (NEDO)

  2. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research and survey for development of solar cell of new power generation device structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Attention is paid to behavior at the molecular level with reference taken to the photosynthetic mechanism, and a behavioral mechanism is proposed, which incorporates, in place of the conventional band model, a concept of a molecular structure based on electron transfer, excitation energy transfer, and reactions of oxidation and reduction. Discussion is then made on elements of technology development for the embodiment of high-efficiency organic ferroelectric thin-film solar cells. The elements taken up include the feasibility of organic ferroelectric thin-film cells, photoelctric conversion systems of plants and photosynthetic bacteria, solar cells using donor-acceptor type dyes, organic thin-film solar cells using conductive polymers, and efficient photoexcitation of organic dyes. Fullerene compounds are semiconductive and their band gaps may be controlled to stay within the range of 0.75-1.9eV, and this justifies a hope that they will serve as solar cells. As for TPV (thermophotovoltaic) conversion, it is under development mainly at NASA (National Aeronautics and Space Administration) as a transportable power source based on heat of combustion. Efforts are also being exerted since 1990 in five European countries to develop TPV systems for small-scale cogeneration. (NEDO)

  3. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of novel amorphous solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project intends to improve on large-area amorphous silicon solar cell performance and to develop high-throughput manufacturing technologies for a reduction in the cost of modules. A film substrate type amorphous solar cell structure of the serial connection type named SCAF (series-connection through apertures formed on film) is contrived. Under this method, film formation using a stepping roll system newly developed for glass substrates may be applied, and the number of manhours required is allowed to be less than under conventional serial connection forming processes. The new technique is characterized in that serial connections are established via through-holes provided in plastic substrates. Making use of the technology, progress is attained in the development of high-throughput process technology for film substrate type amorphous solar cells and of efficiency enhancement technology. In fiscal 1997, an electron beam unit for plasma generation aiming at the elucidation of reaction processes in plasma was introduced, and technologies based on the equilibrium discharge technique were developed enabling high-speed a-Si film formation without degradation in film quality. The effect of trace boron addition to the tandem cell bottom I layer was investigated, and a stabilization rate of 8.05% was achieved using a 40cm times 80cm large SCAF cell. In fiscal 1998, endeavors were exerted for similar developments. (NEDO)

  4. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture applied type thin film solar cells with new structure and development of high-efficiency hybrid thin film/sheet solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (oyogata shin kozo usumaku taiyo denchi no seizo gijutsu kaihatsu (kokoritsu hybrid gata usumaku / sheet taiyo denchi no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop low-cost and high-efficiency hybrid thin film/sheet solar cells, research and development has been performed. This paper summarizes the achievements in fiscal 1999. The research is related to a hybrid construction, in which the upper cells of amorphous silicon thin film are formed on the lower cells bonded with micro-crystalline silicon thin film relative to a poly-crystalline silicon sheet. In the technology to form the upper cells, a pin-construction using amorphous silicon thin film made by using the plasma CVD process was adopted, whereas an open circuit voltage of 1.45V, a short circuit current of 13.6 mA/cm{sup 2}, and a conversion efficiency of 13.5% were obtained. In the technology to form the substrate for the lower cells, formation of flat silicon thin plate that can be peeled off was identified as a result of adopting the construction in which a graphite substrate is provided on a rotating cooling body of 12-prism type. With regard to the technology to bond and form the lower cells, electrical properties of hetero-bonded cells were discussed, and an open circuit voltage of 0.605V and a conversion efficiency of 14.3% were obtained as a result of enhancing the film quality and optimizing the film thickness. (NEDO)

  5. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of next-generation thin-film solar cell module manufacturing technology - Development of CIS solar cell module manufacturing technology - Development of high-quality film enlargement technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu / kohinshitsumaku no daimensekika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project aims to establish a manufacturing process that enables both high-quality CuInSe{sub 2} (CIS) film solar cell enlargement and cost reduction and to develop a device structure which uses less heavy metal for the purposes of increasing the CIS thin-film solar cell size and efficiency and decreasing environmental impact. Several element technologies have been established for increasing the area of high-efficiency Cu(In, Ga)Se{sub 2} (CIGS) solar cells. Concerning the enlargement of the photoabsorption layer which is to assume the most important role, it is found that a high-quality CIGS film, which is near homogeneous though within a 10cm times 10cm area, is fabricated by an in-line vapor deposition method. As for dead area reduction and high-speed patterning, it is found that laser scribing works effectively in the patterning of the window layer and photoabsorption layer. As for reduction in the use of heavy metal, a high efficiency of 16.2% is attained in a cell not using a CdS film as expected in the case of a cell using a CdS film, this thanks to a CIGS film surface reforming technique. The technique of junction formation for CIGS solar cells is improved, and then a true efficiency of 18.5% is achieved. (NEDO)

  6. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research aims to achieve a conversion efficiency of 13% and a manufacturing cost of 140 yen/Wp with a 30cm times 30cm Cu(InGa)Se{sub 2}-based thin-film solar cell submodule. Ga and sulfur are combined and a film fabrication technology was developed which would improve on Voc. Concerning Ga, a laminated precursor layer was fabricated and evaluated, which comprised a Cu-25wt%Ga alloy layer and a Ga source which was a Cu-48%Ga alloy layer. Concerning sulfur, the vapor phase selenization temperature and the selenization retention time in an H{sub 2}Se gas atmosphere was allowed to vary for a change in Cu(InGa)Se{sub 2} calcopyrite crystallinity for the study of relations between the amount of sulfur taken in and the solar cell characteristics, and the relations were assessed by EPMA (electron probe microanalyzer). Technologies were developed for the fabrication of high-resistivity buffer layers by solution growth, for the fabrication of window layers (transparent, conductive ZnO film) by sputtering, and for their patterning. Submodules of a ZnO/Zn(O,S,OH)x/Mo structure were fabricated, 10cm times 30cm and 30cm times 30cm in size. The former achieved 12.5% in conversion efficiency, and the latter 11.6%. (NEDO)

  7. Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell / low-cost and large-area module / next-generation thin-film solar cell (Manufacture of thin-film polycrystalline solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Fiscal 1997 is the first year of another 4-year-long research and development phase. In addition to researches for improving on thin-film polycrystalline Si cell efficiency that have been under way, new efforts are started, which include the development of practicality-conscious thin film producing technologies aiming at higher throughput and yield and the development of modularization process technologies which are necessary for putting thin-film cells to practical use. Concerning the formation of a power generation layer on a polycrystalline Si thin film formed by the ZMR (zone-melting recrystallization) process, studies are conducted for improvement on its throughput and yield using a new CVD (chemical vapor deposition) unit. A method of modularization is evaluated, which involves a laminate of a thin-film cell attached to a resin-coated, reinforced glass substrate and an EVA (ethylene vinyl acetate) back film. A remarkable achievement is earned toward the practicalization of technologies of thin film formation enhanced in quality and throughput and technologies of thin film modularization. (NEDO)

  8. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and development of technologies to manufacture amorphous silicon/thin film poly-crystalline silicon hybrid thin film solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon / usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Developmental research has been performed on large-area low-cost manufacturing technologies on hybrid thin film solar cells of amorphous silicon and poly-crystalline silicon. This paper summarizes the achievements in fiscal 1999. The research has been performed on a texture construction formed naturally on silicon surface, and thin film poly-crystalline silicon cells with STAR structure having a rear side reflection layer to increase light absorption. The research achievements during the current fiscal year may be summarized as follows: the laser scribing technology for thin film poly-crystalline silicon was established, which is important for modularization, making fabrication of low-cost and large-area modules possible; a stabilization efficiency of 11.3% was achieved in a hybrid mini module comprising of ten-stage series integrated amorphous silicon and thin film poly-crystalline silicon; structures different hybrid modules were discussed, whereas an initial efficiency of 10.3% (38.78W) was achieved in a sub-module having a substrate size of 910 mm times 455 mm; and feasibility of forming large-area hybrid modules was demonstrated. (NEDO)

  9. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of thin film poly-crystalline solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a high throughput forming technology and a modularization technology for thin film poly-crystalline solar cell modules. This paper summarizes the achievements in fiscal 1999. In developing the high throughput forming technology for a high-quality thin film, research has been made on a low-cost VEST process to re-utilize substrates by separating the thin film from the substrate. In the melting re-crystallization process, it was discovered that plasticity deformation of the substrate can be reduced greatly by raising the substrate heating temperatures. It was also found out that substrate warping amount can be reduced to about one-fifth of the conventional amount by making the thickness greater than 1.5 mm and raising the heating temperatures higher than 1300 degree C. In developing the thin film modularization technology, it was indicated that the property improving effect remains the same even if the hydrogen passivation method is changed from the hydrogen ion injection to the hydrogen plasma processing. In the trial fabrication of the thin film modules, a conversion efficiency of 13.1% was achieved in nine-cell structured modules. (NEDO)

  10. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of thin-film polycrystalline solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to realize the practical application of the above-named solar module expected to exhibit higher efficiency and reliability and achieve cost reduction through consumption of less materials. In fiscal 1998, 1) technologies were developed to reduce substrate warpage during recrystallization for the higher-throughput fabrication of high-quality thin films and 2) technologies were also developed for the realization of higher-throughput fabrication of thin films and for efficiency improvement for thin-film modules. Under item 1), experiments were conducted by simulation for reducing warpage to occur in thin-film polycrystalline Si substrates during fabrication by melting and recrystallization. Under item 2), for the development of thin-film cell high-throughput technologies, studies were started on a more practical hydrogen plasma process to challenge the conventional process of crystal defect inactivation by hydrogen ion injection with which achievement of high throughputs is difficult. For the development of technologies for the enhancement of thin-film module efficiency, efforts were exerted to realize a 10cm times 10cm square shape for the enhancement of efficiency in the process of filling modules with cells. These efforts achieved a great step toward future practical application. (NEDO)

  11. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of CIS solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihtsu (CIS taiyo denchi module no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a technology to manufacture CIS-based thin film solar cells. This paper summarizes the achievements in fiscal 1999. In the research of a large-area light absorbing layer manufacturing technology, investigation was made on light absorbing layers in manufacturing sub-modules with a size of 30 cm times 30 cm. With regard to the temperature condition in the light absorbing layer forming process, it was found that the cooling rate affects particularly the adhesion in the connecting interface of the light absorbing layer and the Mo rear electrode layer. In addition, it was revealed that the sulfur take-in amount can be increases by extending the retention time at the sulfurizing temperature and by decreasing the temperature to turn the gas phase into selenium. In the research of elementary technologies to establish the mass production process, developments were performed on the high-resistance buffer layer manufacturing technology, the high-quality window layer film manufacturing technology, and the technology to manufacture rear electrode layer made of high-quality metals. In developing the patterning technology, two kinds of the existing patterning devices were modified and adjusted for patterning the substrates with a size of 30 cm times 30 cm. In addition, a processing device was installed in the conventional manually operated process for module finishing. (NEDO)

  12. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of application type novel-structure thin-film solar cell manufacturing technology - Development of amorphous silicon/thin-film polycrystalline silicon hybrid thin-film solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu / amorphous silicon/usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project aims to manufacture the above for the development of low-cost high-efficiency practical cells. Technologies were developed to homogeneously fabricate films with an average efficiency of 10% or more in a 100mm times 85mm area in a STAR (naturally surface texture and enhanced absorption with a back reflector) structure thin-film polycrystalline silicon (poly-Si) solar cell. The texture shape was improved for a higher light trapping effect and a STAR structure cell highly sensitive to long wavelengths and fit for use for a hybrid cell bottom layer was obtained. Various cells were examined for temperature characteristics, and it was found that thin-film poly-Si cells present a temperature coefficient equal to or less than that of bulk single-crystal silicon systems, and hybrid cells a temperature coefficient similar to that of a-Si systems. The technology was applied to a hybrid solar cell in which an a-Si cell was placed on STAR structure thin film poly-Si cells, and a resultant 3-layer a-Si/poly-Si/poly-Si cell exhibited a stabilization factor of 12.0% after 550 hours of optical irradiation. (NEDO)

  13. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction) (development of technology to manufacture micro light collection type solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    These technological developments are intended to demonstrate module efficiency of a micro light collection type solar cell of 15% by fiscal 2000, and obtain prospect on the module manufacturing cost of 140 yen per watt. Discussions given during fiscal 1997 are as follows: development has been performed on a design method to decide construction of a non-tracking micro light collection type module; in the state of cells being integrated on the module, the cells are arranged minutely and discretely, whereas, with discussions on a method to form them and assessment of the optical system as the main objective, single crystal silicon solar cells with a size smaller than 5 mm were fabricated on a trial basis; problems of forming micro cells by using the wafer cutting process were clarified; micro cells operating on light collection were fabricated trially to extract technological problems in light collecting operation and discuss technical problems in mass production; and development was performed on an evaluation method to analyze the cells' light collecting operation, and discussions were given on a method to estimate power generation amount from the light collection type modules. (NEDO)

  14. Fiscal 1990 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Development of methane fueled aeroengine); 1990 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research efforts went on for the development of advanced materials, that is, intermetallic compounds and fiber reinforced intermetallic compound composite materials. Activities were conducted in the four fields of (1) high specific strength intermetallic compounds, (2) high melting point intermetallic compounds, (3) fiber reinforced intermetallic compound composite materials, and (4) a comprehensive survey. In Field (1), ternary phase diagrams (Mo, Nb) were prepared for Ti-Al-X (X=metal) systems, and studies were conducted of systematic methods for developing Ti-Al based high specific strength intermetallic compound materials. In Field (2), work was started to prepare binary phase diagrams for Nb-Al systems, and studies were conducted about their basic characteristics and characteristic governing factors. A powder manufacturing tester was designed and built, and basic tests were started for powder manufacturing. In Field (3), a success was attained in fabricating a low oxygen fiber rendered infusible by electron beam irradiation, and the infusible fiber was found to be high in quality. Studies were started of coatings for the fiber to achieve still higher performance. In Field (4), technical trends were surveyed, coordination was effected between various technology developing activities, and the results were put to proper management and then disseminated. (NEDO)

  15. FY 1995 annual report on research and development of propulsion systems for supersonic transport aircraft. Pt. 2. Research and development of methane-fueled engines for aircraft; 1995 nendo choonsoku yusokiyo suishin system no kenkyu kaihatsu seika hokokusho. 2. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Described herein are the R and D results of FY 1995 for the total system as part of R and D of propulsion systems for supersonic transport aircraft. For R and D of the intake, researches on aerodynamic flow passages at a combined intake design point of Mach 5 are conducted, in which the effects of the boundary layer are taken into consideration, and the wind tunnel tests are conducted for the combined intake. For R and D of the nozzle, experiments are conducted to establish the techniques for designing exhaust nozzle variable schedules in the turbo region, aerodynamic force in the turbo and ram regions, cooling systems, and composite liners. For R and D of the turbojet engines, the second phase engine tests are conducted with the engine of improved designs and two-dimensional variable exhaust nozzle. The tests produce good results in terms of engine endurance and mechanical soundness of the low-pressure systems. For R and D of the combined cycle engine incorporating the turbojet and ramjet engines, the model tests are conducted to understand aerodynamic characteristics when these engines are switched to each other. (NEDO)

  16. Research report for fiscal 1998. Development of advanced surface processing technology for methane-fueled aircraft engine members (Laser-aided advanced processing system technology); 1998 nendo chosa hokokusho. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (Laser oyo senshin kako system gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the research and development of erosion-resistant abradable materials for the methane-fueled aircraft engine front section, a laser-aided surface reform technology was developed for Ti alloys and the like. In relation with the article 'Intermetallic Compound Coating Formation Technology,' an NiTi sprayed coating containing excess Ni solid solution was found to be quite high in resistance to erosion, and similar to Ti-6Al-4V in resistance to oxidation at 300 degrees C. Furthermore, an MCrAlY erosion-resistant coating was formed capable of resisting oxidation at temperatures higher than 1000 degrees C. In relation with the article 'Spraying Phenomenon Evaluation Technology,' studies were made of combustion synthesis reaction during plasma spraying and of the prediction of flight trajectories of different powders, for which optical fiber dichroic temperature measuring, 2-dimensional imaging, and LDV (laser Doppler velocimetry) were applied in combination. Concerning the spraying of intermetallic compound coatings, a temperature rise occurred when heating by laser was performed simultaneously with the laser-induced combustion synthesis reaction. In relation with the article 'Technology of Multiple Spraying on Curved Substrate,' it was found that the gas cooled method works effectively when spraying an erosion-resistant coating onto a thin Ti alloy made turbine blade. (NEDO)

  17. FY 1991 report on the results of the demonstration test on the methanol conversion at oil-fired power plant. Feasibility study of a new system for the stabilized supply of fuel use methanol; 1991 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Nenryo you metanoru kyokyu antei ka no tameno shin system no kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    As a part of the project on the demonstration test on the methanol conversion at oil-fired power plant, feasibility study was made of a new system for methanol production by using abundant hydraulic power energy overseas and by combining water electrolysis and coal gasification technology, and the FY 1991 results were summarized. As a result of the survey, the following were selected as water electrolysis facilities: high efficiency/high current density/simplification system and solid polyelectrolyte electrolysis system with a high purity of hydrogen gas. As the coal gasifier, the oxygen blown furnace was selected which has a high carbon utilization factor, is able to gasify coal at high pressure, has no unnecessary N{sub 2}, and is being used in the integrated coal gasification combined cycle power system. As methanol synthesis facilities, the MGC/MHI method super converter was selected. Assuming the output of hydroelectric power generation to be 4,000MW, conceptual design of the optimum system was made. The methanol cost was estimated under the conditions written below: cost of hydroelectric power generation at site: 2-5 yen/kWh, coal unit price at site: 5,000-6,000 yen/t, transportation distance: 5,000-10,000 km. (NEDO)

  18. FY 1998 Report on technical results. Part 2 of 2. Research and development of supersonic transportation aircraft propulsion systems (Development of methane-fueled aircraft engines); 1998 nendo choonsoku yusokiyo suishin system no kenkyu kaihatsu seika hokokusho. 2/2. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    The research and development project is conducted for (1) ramjet systems, (2) high-performance turbojet systems, (3) instrumentation/control systems and (4) total systems, in order to develop methane-fueled supersonic transportation aircraft engines, and the intended targets are achieved. This project has ended with preparation of the overall plans of the target engine. Described herein is the R and D of the combined cycle engine, following the results described in Part 1 of 2. This program includes designs and development of (1) the turbojet engine, and (2) combined cycle engine. The item (1) includes studies on cycles, preparation of the overall plans and studies on the systems, and the item (2) includes the designs, ground and altitudes function tests, and ground noise tests. (NEDO)

  19. FY 2000 report on the research cooperation project - Research cooperation in developmental support for oil producing countries. Development of the new field of usage of Orinoco oil for fuel of gas turbine combined power generation; 2000 nendo san'yukoku kaihatsu shien kenkyu kyoryoku jigyo seika hokokusho. Gasu tabin fukugo hatsuden nenryo muke Orinoko oil no shin yoto kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-01

    For the purpose of spreading the usage of Orinoco crude oil which is suffering from sluggishness in the export and heightening the economical efficiency in Venezuela, research cooperation was made for a project for reduction of the power cost and environmental loads in Japan by producing the advanced gas turbine use fuel oil from Orinoco oil and exporting it to Japan. In this project, conducted were the technical verification that the gas turbine use fuel oil (GTF) can be produced from Orinoco oil and the economical verification based on the result thereof. As a result of the technical verification, it was confirmed that from the Orinoco crude oil which is heavy, high in sulfur and high in heavy metal concentration, a refined oil satisfying the following properties of the advanced gas turbine fuel oil could be trial-produced using the distilling unit, SDA unit, desulfurizer and de-metaling unit: vanadium concentration: 0.5 wtppm or below; sodium + potassium concentration: 1.0 wtppm or below; viscosity: 20 cSt or below at 135 degrees C. Further, from the economical verification, the good result was obtained that the price was lower than the LNG price and the domestic price of A heavy oil/C heavy oil. (NEDO)

  20. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research on energy (Research and development of biofuel production using highly functional bioreactor - 2nd year); 1999 nendo kokino bio reactor ni yoru bio nenryo seisan ni kansuru kenkyu kaihatsu seika hokokusho (dai 2 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Microbes capable of a high biodiesel fuel (BDF) yield from moisture-containing oils assumedly waste oil are investigated. Lipase attributed to Rhizopus oryzae exhibits a high reaction rate of not lower than 90%. The process functions even when microbes are immobilized by BSPs. BDF does not affect driving performance, and black smoke is reduced. A process basic to industrial production is developed by use of a fixed bed reactor. In the production of ethanol from starch thanks to plural kinds of glucoamylase producing yeast, ethanol is produced at a rate of 7-8% under microaerophilic conditions in both proliferation and fermentation periods, which means a success achieved in growing arming yeast equipped with enhanced functions. A 20-liter class bench plant is installed and immobilization by BSPs is tested, when no problem is detected. In a reaction involving these immobilized microbes, a reaction rate near 16% is achieved. In the production of ethanol by yeast immobilized by BSPs, use of a fuzzy control system is studied, and it is found that prolonged stability is available when glucose concentration is sustained at 10-20g/liter. (NEDO)

  1. Achievement report for fiscal 1997 on the Super/Hypersonic Transport Propulsion System Research and Development Project. 1/2. Development of methane-fueled aeroengine; 1997 nendo choonsoku yusokiyo suishin system no kenkyu kaihatsu seika hokokusho. 1/2. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to develop a ramjet engine for hyper/supersonic transport planes to fly at Mach 2.5-5. A combustion test is conducted and the targeted NOx emission level is attained. It is now expected that the application of heat resistant composite liners to the combustor will lead to a successful cooling structure. In the modification of the design for an increase in engine thrust, a net thrust of 1132N is achieved. In the study of turbojet elements, a success is attained in avoiding resonance at a design point in fan static vane natural oscillation. Concerning the low-pressure turbine, the targeted adiabatic efficiency of 90% is attained at the design point expansion ratio. In the study of a combined intake that exhibits high performance across a range of plane take-off through Mach 5 flight, shock waves are controlled with stability in a wind tunnel test. Targeted levels in noise control are attained in a flight simulation noise test using a fiscal 1997 reduced scale model. The compatibility of metal materials peripheral to a real engine with lubricating oils and their carbonization at high temperatures are evaluated. A lubricating oil is finally selected, and the temperature domain for its use is determined. The experimentally built combined cycle engine is found to be mechanically sound presenting no problem for instance in relation to methane fuel ram ignition performance. (NEDO)

  2. Fiscal 1993 R and D project for industrial science and technology. Report on results in developing methane-fueled aircraft engine (R and D on silicon-based polymeric material); 1993 nendo methane nenryo kokukiyo engine kaihatsu seika hokokusho. Keisokei kobunshi zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    R and D was conducted on silicon-based polymeric materials for structural use, for the purpose of establishing fundamental technologies such as molecular design, synthesis, material forming and evaluation method concerning silicon-based polymers, with the fiscal 1993 results summarized. In the studies of synthesis technologies of silicon-based polymeric materials having a sea-island structure, a series of polymers with an Si-C main chain structure were prepared by ring-opening polymerization of the cyclic monomers. In the studies of interpenetrating polymer network (IPN) structure forming technologies, polycarbosilanes with superior thermal stability and solvent solubility were synthesized through structural control based on molecular design. In the studies of composite structural materials between organic metallic complex and silicon-based high polymer, the compounding was carried out by introducing or blending organic metallic complex into the main chain of silicon polymer, with evaluation made on the heat resistance. The studies of silicon polymer structural materials having a ring structure were conducted on high heat resistant polymers that were obtained by dehydrocoupling polymerization with magnesia as a catalyst. (NEDO)

  3. FY 1999 Report on the technical results. Research and development project for quick-effect type international standards for creating new industries (Standardization of quality and testing methods of automobile fuels and lubricants); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Jidoshayo nenryo nado no seihin hinshitsu shiken hoho no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is conducted for the method of evaluating the effects of fuel oils on automobile engines (combustion chamber deposit), testing of valve trains of diesel engines, and testing the effects of gasoline engine oil on oil seal rubber (oil seal compatibility), with the objective to propose the international standards. In the study of the combustion chamber deposit, the combustion chamber deposit method is applied to the road running mode, to clarify that this method is well correlated with the market conditions. In the study of wear of the valve train of diesel engines, the two diesel engine oils, now adopted by the European valve train wear testing method, are applied to the JASO testing method, to clarify that the JASO method is internationally applicable. It is concluded that these two methods can contribute to the international standardization. In the study of the oil seal compatibility, the effects of testing period and engine oil type are investigated, to clarify that this method should be further developed to serve as the international standard. (NEDO)

  4. Fiscal 1992 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Development of methane fueled aeroengine); 1992 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Research and development was carried out for intermetallic compounds and fiber reinforced intermetallic compound composite materials for use as advanced materials at high temperatures. Activities were conducted in the four fields of (1) high specific strength intermetallic compounds, (2) high melting point intermetallic compounds, (3) fiber reinforced intermetallic compound composite materials, and (4) a comprehensive survey. In Field (1), Mo, Nb, and Cr were added to Ti-Al systems and ternary phase diagrams were prepared for them, and isostatic forging was combined with heat treatment for the collection of basic data for achieving an optimum microstructure. Basic technologies were established for the manufacture of sheets by isothermal rolling. In Field (2), Ti, Ta, and W were added to Nb-Al systems and partial ternary phase diagrams were prepared for them. Specimen materials were subjected to a high-temperature compression test, when a specimen containing 10% of W recorded 230MPa at 1,600 degrees C. In Field (3), a silicon carbide based fiber was developed and it demonstrated the excellence of low oxygen fibers with respect to thermal properties after being rendered infusible by electron beam irradiation. (NEDO)

  5. FY 1998 Report on technical results. Part 1 of 2. Research and development of supersonic transportation aircraft propulsion systems (Development of methane-fueled aircraft engines); 1998 nendo choonsoku yusokiyo suishin system no kenkyu kaihatsu seika hokokusho. 1/2. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    The research and development project is conducted for (1) ramjet systems, (2) high-performance turbojet systems, (3) instrumentation/control systems and (4) total systems, in order to develop methane-fueled supersonic transportation aircraft engines. For the item (1), the ram combustor for the target engine is designed to evaluate its performance, and the shock-position within the dummy intake is successfully controlled by the variable exhaust nozzle. For the item (2), the R and D efforts are directed to the fans and low-pressure turbines, the former covering the studies on the single-stage elements for the fans of high flow rate, and the elements for the 2-stage, high-efficiency, high-load fans. For the item (3), the R and D efforts are directed to the electronic control systems and electro-optical measurement systems, the latter including development of the improved optical positioning and rotational sensors operating at high temperature of 350 degrees C. For the item (4), the R and D efforts are directed to intake nozzles as the total system component, noise reduction technology, and cooling and new material application technologies. (NEDO)

  6. Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of technologies for producing substitute fuel for petroleum by utilizing organisms; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technologies of producing useful substances using the substance decomposing/producing functions of complex biosystems and methods of their handling are developed. In the utilization of microbes in the digestive tracts of termites and longicorns, it is made clear that several kinds of termites cleave the {beta}-O-4 ether linkage. In relation to technologies for wood decomposing complex microbial system construction and complex vector system development, a screening system is constructed in which strains that exhibit complex actions are combined. Concerning the advanced utilization of tropical oil plants, conditions are determined for inducing callus out of oil palm tissues. Out of oil palm sarcocarp tissues, mRNA (messenger ribonucleic acid) is isolated for the construction of a cDNA (complementary deoxyribonucleic acid) library. For the purpose of isolating a powerful promoter, a partial base sequence is determined for ubiquitin that frequently expresses itself in cells. A pathogenic bacterium ailing the oil palm is sampled for identification, and it is inferred that the bacterium is a kind of Ganoderma boninense. (NEDO)

  7. FY 1997 report on the results of the industrial technology R and D project. Development of technology to use biological resources such as the complex biological system (Development of biological use petroleum substitution fuel production technology); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Experimental researches were conducted and the FY 1997 results were reported with the aim of establishing analytical technology for the complex biological system by which the complex biological system can be analyzed in such a state as it is using the molecular biological method. In the study of the molecular genetic analytical technology, PCR primers used for amplification of topoisomerase II genes of the whole eukaryote was designed. As to the histochemical analytical technology, a study was made on the new constitution microorganism detection method by the hybridization method and the antibody specific dyeing method, and the following were conducted: manifestation in quantity of colibacillus and the recovery, refining, and construction of peptide library by fuzzy display method. Concerning the functional analytical technology, technological researches were made such as the environmental adaptation mechanism of high thermophile and the information transfer mechanism among bacteria through cell membranes for elucidation of the special environment detection/response mechanism and the special environment adaptation/resistance mechanism. As to the separation/culture technology, various anaerobic microorganisms were separated from marine sponge for the development of a method of culturing in 3D matrices. (NEDO)

  8. FY 1995 annual report on research and development of propulsion systems for supersonic transport aircraft. Pt. 1. Research and development of methane-fueled engines for aircraft; 1995 nendo choonsoku yusokiyo suishin system no kenkyu kaihatsu seika hokokusho. 1. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Described herein are the R and D results of FY 1995 for ramjet, high-performance turbojet, control/measurement and total systems. For R and D of the ramjet system, the combined component test is conducted, using a dummy intake which simulates the flow pattern downstream of the intake throat, ram combustor and variable exhaust nozzle. The first free jet test is successfully conducted at a combustor exit temperature of 1900 degrees C. For R and D of the high-performance turbojet components, the experimental researches are conducted on fan components, a combustor, and high-performance, variable, low-pressure turbine. For R and D of the control/measurement system, the system developed is improved by incorporating a dual redundant FADEC. The engine test produces good results. For R and D of the total system, the R and D efforts are made for the intake, nozzle, noise reduction, cooling and application of new materials, and combined cycle engine. (NEDO)

  9. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

  10. Achievement report for fiscal 1997 on the Super/Hypersonic Transport Propulsion System Research and Development Project. 2/2. Development of methane-fueled aeroengine; 1997 nendo choonsoku yusokiyo suishin system no kenkyu kaihatsu seika hokokusho. 2/2. Methane nenryo kokukiyo engine no kaiahtsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A technology is developed of integrating a turbo system and a ram system into a combined cycle engine. In fiscal 1997, an experimentally built engine is subjected to its first ground test and attains the expected result, and preparations are made in full swing for a high-altitude performance test scheduled for fiscal 1998. No problems relative to design criteria and mount structure load are detected in a total oscillation analysis and fan blade off analysis, this verifying the reasonableness of the design. The heat transfer module as designed is also found equipped with sufficient strength. The engine attains the maximum rotation speed in the ground test, and is found stable in operation. Although the vibration of the shaft and outer shell stays in a domain not suggesting a trouble, yet the vibration of the low-pressure turbine blade is beyond the limits in a certain domain. Tests are repeated after defining a domain where sustained rotation is forbidden. The secondary air system operation is found normal. The newly added MSV (mode selector valve), and the variable system and ram fuel control of FVABI (front-variable area bypass injector: important for switchover from turbo mode to ram mode), are also found normal in operation. The function, ignition, and zoning sequence of the ram combustor are found valid. (NEDO)

  11. Fiscal 1991 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Development of methane fueled aeroengine); 1991 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Research and development was carried out for intermetallic compounds and fiber reinforced intermetallic compound composite materials for use as advanced materials. Activities were conducted in the four fields of (1) high specific strength intermetallic compounds, (2) high melting point intermetallic compounds, (3) fiber reinforced intermetallic compound composite materials, and (4) a comprehensive survey and research. In Field (1), ternary phase diagrams (Mo, Nb) were prepared for Ti-Al-X (X=metal) systems, and studies were made of alloy designs for Ti-Al based high specific strength intermetallic compounds. In Field (2), binary phase diagrams were prepared for Nb-Al systems, and the effect of phase and structure on their basic properties were investigated. A powder manufacturing tester was designed and built, and basic powder manufacturing tests were conducted. In Field (3), studies were made of heat treatment and surface coating technologies, and a silicon carbide based fiber was developed, excellent in oxidation resistance. In Field (4), technical trends were surveyed, and studies were made as to basic technical tasks to discharge for the development of materials for aeroengines. (NEDO)

  12. Research report for fiscal 1998. Basic research for promoting joint implementation, etc. (fuel change plan for No. 1 and No. 9 Irkutsk Heat and Power Co-Generation Plants, Irkutsk, Russia); 1998 nendo chosa hokokusho. Roshia renpo Irkuktsk shu dai 1 go oyobi dai 9 go Irkutsk netsu heikyu hatsudensho nenryo tenkan keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A research is conducted to find out if efficiency will increase and greenhouse gas will decrease when fuel is changed from coal to gas at the above-named plants, and the economics of the plan is reviewed. The No. 1 plant comprises 18 coal-fired boilers with a total design capacity of 2985 tons/hour, and 8 steam turbine generators rated at 185MW, constructed in the 1940s. The No. 9 plant was constructed in the 1960s and 1970s. Four different modifications programs are drafted to study the fuel change plan. As the result, it is found that the addition of natural gas burning facilities to the existing heat and power co-generation plants and the modification of the existing boiler-related facilities will be low in earning rate and reliability, though excellent in budget size and cost efficiency; and that to dismantle the existing plants and to newly construct heat and power plants operating on gas turbines will bring about a higher earning rate, fuel cost reduction effect, and reliability, though such will cost more. (NEDO)

  13. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

  14. Achievement report for fiscal 1992 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on forbidden band width optimization); 1992 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Kinsei taifuku no saitekika no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Research is carried out on technologies concerning CuInSe{sub 2} thin-film solar cell manufacturing, thin film formation, thin film characterization, CdS, (CdZn)S formation, CuInSe{sub 2} single junction, analysis of the a-Si/CuInSe{sub 2} tandem solar cell operating theory, etc. In relation with the encapsulated selenization method for film formation for CuInSe{sub 2} thin-film solar cells, film constitution, film thickness, selenization temperature, etc., are studied for optimization. In relation with the vaporized selenization method, vaporized selenization is tested in a vacuum chamber aiming at improved homogeneity and reproducibility. In research on CdS and (CdZn)S which are window layer materials for CuInSe{sub 2} thin-film solar cells, CdS thin films are formed in a solution growth method using CdSO{sub 4} and (NH{sub 2}){sub 2}CS. In relation with the solution growth of the (CdZn)S crystal film, control of the Zn content in the film is now practicable. In the study of a-Si/CuInSe{sub 2} tandem solar cells, an analytical program is formulated, and calculation is made concerning the impacts of CuInSe{sub 2} forbidden band width and a-Si i-layer thickness. (NEDO)

  15. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research on amorphous silicon defect density); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (Amorphous silicon no kekkan mitsudo no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    So as to determine the energy distribution of defect level density in a-Si, which is indispensable for an optimum solar cell design, the hitherto unclear theoretical relationship between the field effect method and MOS (metal oxide semiconductor) capacity method is made clear, and a unified theory is newly established. A high-speed totally automatic evaluation system is developed, capable of high-accuracy determination of defect levels. For the realization of an a-Si MOS structure required for fulfilling the above purpose, a-Si is grown and then diborane and ammonia are subjected to a glow discharge decomposition process for the formation of a new insulation film. It is found that the material may be utilized for MOS structure construction for defect density evaluation. Studies are conducted on plasma emission spectroscopy and infrared absorption analysis for the elucidation of growth mechanism for the growth of high-quality a-Si. Key radicals in plasma that govern film growth are investigated. It is disclosed that excited hydrogen in plasma plays an important part in microcrystalline phase deposition. It is also disclosed that hydrogenation greatly improves on CVD (chemical vapor deposition) a-Si doping efficiency. (NEDO)

  16. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Tandem type solar cells are developed, in which solar cells with different band gaps are stacked for effectively utilizing optical energy across the entire range of solar spectrum. A material gas supply control device for multiple epitaxial growth was added to a large-area GaAs film epitaxial growth unit, and a film thickness homogeneity of {+-}1% was achieved. A GaInP epitaxial layer fabricated in the same way was also enhanced in homogeneity. A low-carrier concentration layer was inserted into the top cell GaInP p-n junction for the construction of a p-i-n structure, and this improved on the short-circuit current. Furthermore, a p-p-i-n structure was constructed having two emitter layers, and this improved on spectral sensitivity for the achievement of a conversion efficiency of 13.6%. Studies were conducted about the tunnel junction which plays an important role in the stacking of cells, and the tunnel peak current was increased to 7.41A/cm{sup 2}. Fabrication is now under way of a GaInP/GaAs stacked cell, which is expected to exhibit a conversion efficiency of 25% or higher. In the case of a GaInAs cell to serve as the bottom cell, a conversion efficiency of 5.1% was achieved. Consequently, it is safely expected that a 3-junction stack of GaInP/GaAs//GaInAs will exhibit a conversion efficiency of 30% or higher. (NEDO)

  17. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of technologies to manufacture ultra-high efficiency crystalline compound solar cells; 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on laminated cells comprising of GaInP/GaAs//GaInAs using poly-element compound semiconductors. This paper summarizes the achievements in fiscal 1999. In developing the technology to manufacture large-area ultra-high efficiency cells, fabrication of 5-cm square GaAs cells was worked on, and a conversion efficiency of 24.7%, which is equivalent or better than that for 1-cm square cell, was achieved by using the epitaxial growth temperature for the GaAs cell structure of 600 degrees C, by adopting the p-on-p structure and by making the electrode thicker by using the plating method. Furthermore, trial fabrication was performed on 5-cm square cells also on GaInAs as the bottom cell. A conversion efficiency of 4.6% was obtained in a 5-cm square cell as a result of high level homogenization of film thickness and composition by optimizing the gas flow in growing GaInAs onto an InP substrate, and using a growth temperature of 550 degrees C. In developing the technology to form GaInP/GaAs laminated cells, discussions were given by using 5-mm square cells on especially improving the GaInP crystallinity and reducing the series resistance in the window layer. GaInP/GaAs-2 bonded lamination cells were fabricated, whereas a conversion efficiency of 19.63% was obtained without using a reflection preventing film. (NEDO)

  18. Achievement report for fiscal 1981 Sunshine Program on development of practical application technologies for photovoltaic power systems. Test production and verification of solar panels (Development of polycrystalline substrate process technologies); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi panel jikken seisaku kensho (takessho kiban kotei no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Studies are conducted to enlarge the diameter of polycrystalline Si castings and to develop a low-loss slicing method using silicon nitride powder as mold releasing agent. The apparatus for Czochralski's pulling process is improved and tested using SEG (selective epitaxial growth) Si, and now the casting of a 150mm-diameter ingot is feasible. Also, test production of a 94mm-square wafer as specified by NEDO (New Energy and Industrial Technology Development Organization) is successfully carried out. Difficulties in separating the mold releasing agent from the crucible are solved by changing the Si{sub 3}N{sub 4} power solution from PVA (polyvinyl alcohol) to ethyl silicate. The design, manufacture, and installation of the important parts of the system for the mass production of castings are now complete. The crucible is designed to be movable relative to the heater section, and the molten Si is allowed to cool and solidify from the bottom upward. In relation with the development of low-cost wafer manufacturing technologies, low-loss slicing methods are studied. It is concluded that under the current circumstances a multi-blade saw is more promising than the multi-wire saw in view of the damaged slice rate, processing speed, operating cost, and maintainability. (NEDO)

  19. Achievement report for fiscal 1991 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on forbidden band width optimization); 1991 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Kinsei taifuku no saitekika no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Research is conducted on film formation technologies etc. for the chalcopyritic compound semiconductors represented by CuInSe{sub 2} which is the most excellent of the materials for thin-film solar cells. As for the development of a encapsulated selenization method, research is conducted on an In formation method, temperature program for heat treatment, and Cu-In alloy film selenization, and then a CuInSe{sub 2} film less to suffer phase separation is obtained. In the development of a vaporized selenization method, the reactor tube and the temperature program are improved, and this results in a CuInSe{sub 2} film excellent in homogeneity. As for the evaluation of CuInSe{sub 2} film, photoluminescence is measured using a solid-phase selenized film, vapor-phase selenized film, and 3-source vapor-deposited film, and the result shows that photoluminescence-assisted CuInSe{sub 2} film evaluation is quite promising. In the development of ZnO film formation technologies, the MOCVD (metalorganic chemical vapor deposition) technology is almost complete, and film formation on a 10cm-square substrate is now practical. (NEDO)

  20. Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of solar energy technologies (Research and development of SnO{sub 2} solar cells); 1981 nendo taiyo energy gijutsu no kenkyu kaihatsu seika hokokusho. SnO{sub 2} taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    The aim is to establish the technology of manufacturing SnO{sub 2}/nSi solar cells using a low-temperature deposition method and thereby to reduce the cost. A 5cm-diameter wafer is subjected to a batch process, and a large-area, uniform-quality SnO{sub 2} film is obtained. A conversion efficiency of 13.7% is achieved for a single-crystal 9cm{sup 2} cell. As for the conditions of electrode formation, conventional methods are applied for bonding metals, which are Sn, Ni, Zn, etc., for the surface electrode and rear electrode. Vapor deposition is found to be the most excellent. Since it is known that ohmic characteristics improve when Cr is inserted as the base for the surface electrode rear electrodes, it is anticipated that a contact resistance value not inferior to that by vapor deposition will be achieved once the method of Cr bonding, whether by printing or plating, is established. An n-type low-cost polycrystalline Si substrate is subjected to etching under the optimum conditions, and a conversion efficiency of 9.6% is achieved for a 0.5cm{sup 2} cell. An SnO{sub 2} film is formed on a uneven surface for a reduction in the single-crystal cost, when characteristics better than those of a wafer manufactured by surface polishing are realized. Experimentally produced cells are evaluated using a solar simulator, and the result indicates that the electrode forming conditions influence conversion efficiency a great deal. (NEDO)

  1. FY 1977 Annual report on Sunshine Project results. Research and development of photovoltaic power generation systems. (Research and development of solar cells of II-VI group compound semiconductor); 1977 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. II-VI zoku kagobutsu handotai taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-31

    This project is aimed at establishment of techniques for pollution-free production of II-VI group compound semiconductor type solar cells. The research items are (1) measures against aging, (2) methods for production of II-VI group compound semiconductors and for forming their joints, and (3) method for assembling solar cell devices.For the item (1), the aging tests are conducted for sintered film type CdS/CdTe solar cells. The C electrode is found to be less aged than the others. The aging tests for the CdS/Cu{sub 2}S cells indicate that it takes 10 years or longer for the performance to be halved under commercial conditions. For the item (2), the sintered film type CdS/CdTe solar cells can be produced by a mass-producible process of screen printing and belt furnace. This production method is promising for producing the solar cells at low cost. For the item (3), it is found that series resistance of the solar cell devices increases as the assembly area increases, resulting in decreased conversion efficiency. The divided structure of the CdTe layer is desired to avoid the above problem. Dividing each unit device increases intrinsic conversion efficiency, but decreases effective power generation area ratio. It is therefore necessary to improve printing precision. (NEDO)

  2. Fiscal 1976 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on 2-6 group compound semiconductor solar cells); 1976 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. 2-6 zoku kagobutsu handotai taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-31

    This report describes the fiscal 1976 research result on 2-6 group compound semiconductor solar cells for photovoltaic power generation systems. The research aims at the system less than 1/100 in cost. Vapor deposition resulted in failure to obtain high-efficiency cells. Vapor-phase growth revealed Cd-Te single-crystal solar cell is promising, however, resulted in failure to obtain high-efficiency thin film elements. Both chemical deposition and sintering succeeded in mass production of prototype high-efficiency elements equal in performance. However, since chemically deposited CdS film is too thin having higher serial resistance, it requires In{sub 2}O{sub 3} auxiliary transmissive electrodes on glass substrates. Since CdTe film and CdS film also require completely different vapor deposition processes in hetero- junction, chemical deposition is more disadvantageous in cost than sintering. CdTe thin film fabricated by screen printing/sintering is most promising. Since Cd is harmful to human bodies, study was made on pollution preventive measures in its production or use stage, and accidents or fires, obtaining some results. (NEDO)

  3. Achievement report for fiscal 1991 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on low-temperature film formation technology); 1991 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Teion seimaku gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    For the establishment of a low-temperature formation technology for compound semiconductor polycrystalline thin film of CuInSe{sub 2}, research is conducted involving film formation and film quality evaluation using the ICB (ion cluster beam) method. In the research on the film formation, an In-excessive film is placed on a Cu-excessive CuInSe{sub 2} film using the ICB method for the formation of a two-layer film. Bulk CuInSe{sub 2} and thin-film polycrystalline CuInSe{sub 2} are evaluated using PL (photoluminescence) spectrums excited by YAG (yttrium aluminum garnet) and Ar. In both bulk and thin film, it is suspected that clues are latent in the levels deeper than hitherto reported. A luminescent belt of 0.75eV is detected. Changes in film quality before and after oxygen annealing are verified using the YAG-excited and Ar-excited PL spectrums, and the result suggests the feasibility of tracking the process in which the effect of annealing propagates inward from the interfacial surface. Fe-added single-crystal CuInSe{sub 2} is investigated for the optical and photoelectrical effects of Fe impurities. (NEDO)

  4. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research, development, and survey of crystalline solar cell evaluation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (kesshokei taiyo denchi hyoka system no kenkyu kaihatsu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the basic study of ultrahigh-efficiency cells, the technology of ribbon crystal growing is again attracting attention for shortage of Si material supply. The new technology and problems to solve for cost reduction for it are discussed. Concerning the bulk type crystalline Si which is a core material, recent trends are mentioned involving studies of basic substrate properties such as the photoabsorption coefficient and crystal defects for achieving higher efficiency, development of gettering and surface passivation technologies, enhancement of processing speeds, radiation concentration behavior, etc. Newly obtained findings about photodegradation are mentioned, and some remedial measures are described. Recent reports on the application of porous Si to solar cells are compiled. In connection with the development of low-cost quantity-production process technologies, a remarkable progress recently marked by polycrystalline Si solar cells is described. Furthermore, it is stated that new process technologies will be required in the fields of material refining, substrate manufacturing, and cell fabrication. A proposition is presented aiming at developing cell modules compatible with application systems and practicalizing modules that may be integrated with roofing materials. Reference is also made to surveys overseas. (NEDO)

  5. Achievement report for fiscal 1984 on Sunshine Program-entrusted research and development. Research and development of amorphous solar cells (Research on amorphous silicon interface); 1984 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Amorphous silicon no kaimen no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    As for the formation of amorphous semiconductors by photo-CVD (chemical vapor deposition) processes, details are examined of a-Si formed by the excimer laser-excited photo-CVD process, a-SiC formed by the directly excited photo-CVD process, a-SiGe formed by the mercury sensitized reaction photo-CVD process, and {mu}c-Si formed by the mercury-sensitized reaction photo-CVD process. It is then found that all of the said materials are superior to a product of the plasma CVD process in terms of film quality. As for the fabrication of amorphous Si solar cells by a photo-CVD process, a 3-separate-chamber unit is built, in which all the p-, I-, and n-layer are formed by photo-CVD. It is then found that the introduction of a buffer layer into the p/I interface is a powerful tool to enhance efficiency and that the use of the buffer zone brings about an increase of 9% or more in conversion efficiency. In the case of an amorphous solar cell using monosilane, buffer layer introduction results in a conversion efficiency of 9.05%. (NEDO)

  6. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system (development of technology to manufacture thin film solar cells (surveys and researches on analyzing practical application )). Volume 1; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is intended to identify and analyze quickly and accurately the technological trends inside and outside the country on thin film solar cells, to reflect the results effectively on research and development of practical application of the thin film solar cells for power use, and to aid the research on practical application of the technology to manufacture the thin film solar cells. This fiscal year introduced the new project of researching and developing the poly-crystal silicon-based thin film solar cells. Discussions were given on designing the solar cells, including setting of thickness of an active layer required to improve efficiency of the silicon-based thin film solar cells, the light confining technology, and surface passivation. Comparisons and discussions were given on the new amorphous/poly-crystal silicon thin film manufacturing method and the conventional plasma CVD process. A research development program was introduced for a super laboratory to aid establishing the practical application technology for the silicon-based thin film solar cells. Chalcopyrite compounds including CuInSe2, and CdTe have not shown deterioration even in a long-term outdoor exposure test, hence they are noted as materials for high-efficiency solar cells and studied actively. Although still small in area, the net conversion efficiency was found in the order of 17%. Technological development has started to search mass production processes and commercialization possibility in the future. (NEDO)

  7. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research and development of production of low-cost monosilane); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (tei cost monosilane seizoho no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    A low-cost production method is developed for monosilane as a cell film material, 99.9995% pure at a manufacturing cost of 4,500 yen/kg (100 ton/year unit). An experimental unit with a maximum capacity of 1m{sup 3}/H (1 ton/month) gas production is built, and whether it is practical will be clarified by the end of fiscal 1983. The whole monosilane production process, consisting of the electrolysis of eutectic liquid of Li chloride and K chloride, hydrogenation of Li to be generated by the electrolysis, and the generation of monosilane through the reaction of the hydrogenated Li and silicon tetrachloride, proceeds in one large molten salt tub. The chlorine from the electrolysis and Si as material comes into reaction in a salination furnace for the generation of silicon tetrachloride to be supplied to the process. Minor tests are made involving pressure control, distance between the electrodes and the effect of the diaphragm, stirring in the hydrogenation chamber, dust in the monosilane generation chamber, and the insulation of the cathode lead rod, and the results are reflected on the process of experimental unit designing and building. The unit has harm neutralizing facilities for safety assurance because much hydrogen and a little chloride are consumed while the unit is in operation, with some silicon tetrachloride to be retained in the unit. An infrared absorption method is used to analyze impurities in the monosilane gas, when the method exhibits a capability of detecting 2ppm of methane. (NEDO)

  8. Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of amorphous solar cells (Research on amorphous silicon-based new materials); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Amorphous silicon kei shinzairyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In an a-Si{sub 1-x}Ge{sub x}:H film formed by decomposition in a glow discharge, since Ge-H is weaker than Si-H in terms of bonding, an increase in the amount of Ge decreases the amount of H and increases the number of Ge dangling bonds (DBs). Actually, however, H bonded to Si also decreases the number of DBs in Ge. This suggests that H is not working only to terminate DBs but that it also decreases the number of DBs through its structure-softening effect. In the case of a-Si{sub 1-x}C{sub x}:H, an increase in C results in an increase in H and in the number of DBs in both Si and C, this because C-H is stronger than Si-H in terms of bonding. F in a film is quite mobile. SiF and SiH in presence as distributed are found to decrease the number of DBs. Concerning the effect of hydrogen plasma processing for a-Si formed by thermolysis (CVD: chemical vapor deposition), the light transmission rate, absorption, ESR (electro-spin resonance) process time, and dependency on film thickness are investigated, and the relationship is examined between the defect-reducing effect of the H taken into the film and the transmission of light. It is found, as the result of experiments by a simplified molecular orbital method, that DBs stay in existence keeping away from where H or F is in presence. (NEDO)

  9. Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on 2-6 group compound semiconductor solar cells); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. 2-6 zoku kagobutsu handotai taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-31

    This report summarizes the fiscal 1974 research result on 2- 6 group compound semiconductor solar cells. To obtain a probability of the technology for producing photovoltaic power generation systems at a cost less than 1/100 of those by current technology, this research aims at establishment of the pollution-free production technology of the titled solar cells, and development of an innovative photovoltaic power generation system using such solar cells. The research is composed of (1) study on deterioration mechanism, (2) measures against pollution, and (3) basic study on the production system of such semiconductors. In the 1st research, the analysis result showed that deterioration under solar radiation or by short circuit is derived from an increase in resistance around a positive electrode and a decrease around a junction caused by change in Cu{sub 2}S composition due to migration of Cu ions in a Cu{sub 2}S layer by photo current. In the 2nd research, study was made on preventive technology of Cd pollution. In the 3rd research, basic study was made on the production systems of semiconductors such as sintering, chemical separating and vapor-phase growth for cost reduction. (NEDO)

  10. Development in fiscal 1998 of silicon manufacturing process to rationalize energy usage. Surveys and researches on analysis of practical application of technology to manufacture silicon raw materials for solar cells; 1998 nendo energy shiyo gorika silicon seizo process kaihatsu seika hokokusho. Taiyo denchi silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to develop a mass production technology to manufacture silicon raw materials for solar cells, and assist its practical application, surveys and analyses were performed on trends in development of the related technologies, the problems therein , market trends and industrial trends thereof. This paper summarizes the achievements in fiscal 1998. The worldwide production amount of solar cells in 1998 is estimated to have achieved 150 MW, and the silicon consumption reached the level of 2,300 tons. In spite of the economic recession environment, there was no change in the expansion trend. In developing an SOG-Si mass production and manufacturing technology, construction of pilot plants for each process has been completed, and entered into the operation research phase. In developing a technology to manufacture high quality poly-crystalline silicon substrates, fabrication has been completed on the on-line ingot cutting equipment and the plasma heating equipment, and the stage is now in operation research of continuous electromagnetic casting process. The conversion efficiency of the poly-crystalline silicon solar cells is 14 to 16% at the mass production level, whose enhancement requires indispensably the improvement in quality of the substrate. Discussions are required on the ingot manufacturing conditions in coordination with improvement in the cell manufacturing technology. (NEDO)

  11. Achievement report for fiscal 1991 on Sunshine Program-entrusted research and development. Research and development of amorphous silicon solar cells (Research on amorphous silicon interface); 1991 nendo amorphous silicon taiyo denchi no kenkyu kaihatsu seika hokokusho. Amorphous silicon no kaimen no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The amorphous solar cell interface has been under study for the enhancement of efficiency and reliability in amorphous solar cells, and this is the compilation of the results achieved in fiscal 1991. In the effort to enhance delta-doped amorphous silicon solar cell efficiency, an amorphous Si solar cell is built using a ZnO film as the transparent conductive film. As the result, an a-Si solar cell with a conversion efficiency of 11.5% is obtained. In the research on the suppression of photodegradation in a-Si, from the viewpoint that a reduction in the amount of hydrogen contained excessively in the film will be effective in decelerating photodegradation, a photoexcited hydrogen radical treatment method is newly proposed, and basic studies are conducted on it. As the result, it is found that an a-Si film processed by a 20-second hydrogen treatment at a substrate temperature of 460 degrees C exhibits a lower photodegradation rate than an ordinary a-Si film. In the research on the deposition of amorphous Si film, a VHF frequency is used instead of 13.56MHz for plasma, and an amorphous Si film is deposited efficiently at a lower voltage at which ions cause less damage. (NEDO)

  12. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology; 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are made to develop a GaInP/GaAs-based compound semiconductor solar cell built on an Si substrate, the Si substrate being lower in cost, higher in mechanical strength, lighter in weight, and higher in heat conductivity than a GaAs or Ge substrate. Fiscal 1999 studies involved improvement on GaAs/Si heteroepitaxial growth and the evaluation of crystallinity in thus grown layers, improvement on cell characteristics, fabrication and evaluation of an n{sup +}/p structure cell, and so forth. As for crystal growing technologies, a 980 degree C 5-heat-cycle annealing method was applied, and the density of dislocation was reduced to 5 times 10{sup 6}cm{sup -2}. In the fabrication of cells, an n{sup +}/p structure cell was studied, and the cell achieved 12.5mAcm{sup -2} in short-circuit photoelectric current over 9mAcm{sup -2} of the conventional p{sup +}/n structure GaInP cell. Without any special effort to optimize the structure, a GaInP/GaAs layer-built cell on a GaAs substrate achieved 23.7% in conversion efficiency. When it is taken into consideration that conversion efficiency on an Si substrate is approximately 80% of what is achieved on a GaAs substrate, it is deemed that the achievement of 23.7% suggests that near 20% in conversion efficiency may become available on an Si substrate. (NEDO)

  13. Achievement report for fiscal 1984 on Sunshine Program-entrusted research and development. Optical research on electronic state in amorphous silicon. (Research and development of amorphous solar cells); 1984 nendo amorphous silicon no denshi jotai no kogakuteki kenkyu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    For realizing a high-performance amorphous solar cell, research is conducted on how to evaluate the amorphous silicon film formed by glow discharge decomposition as regards its optical and photoelectric characteristics, basic physical properties of its electronic states, and its film quality and film forming conditions. Research is conducted on the mechanism of glow discharge decomposition reaction using plasma spectroscopic techniques and on the conditions of film formation, when low-temperature SiO{sub 2} film growth is caused to occur by a directly excited photo-CVD (chemical vapor deposition) method in which a deuterium lamp and Xe lamp are the exciting light sources and SiH{sub 4} and O{sub 2} are the source gases. In research on the mechanism of photoelectric conversion in an a-Si film p-I-n junction system, a method is developed of evaluating physical property parameters in accordance with a field drift type photovoltaic effect model. In research on the evaluation of the optical properties of a-Si films using modulation spectroscopy and polarization analysis, electronic states in the vicinity of the a-Si based thin film band end is examined using an ER method which is one of the modulation spectrometric methods. The constitution and electronic states of a-Si films are studied using a high-speed ion beam scattering method and electronic spectrometry. (NEDO)

  14. Achievement report for fiscal 1984 on Sunshine Program-entrusted research and development. Research and development of photovoltaic power system (Research and development of amorphous solar cells - Research on defect density in amorphous silicon); 1984 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (amorphous silicon no kekkan mitsudo no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    For the development of high-efficiency, large-area, long-life, and low-cost solar cells, research is conducted on new methods of film formation and defect evaluation. Concerning the kinetics of Si thin film, a radical beam deposition method is proposed as a new low-temperature thin film growth method. Using the new method, a {mu}c-Si film is manufactured, through only a purely radical substrate surface reaction of chemically active, electrically neutral excited species. In research on the amorphous semiconductor superlattice, a new study is conducted on a multilayer, cyclic-structure superlattice consisting of thin films of a-Si:H and a-Si{sub 1-x}N{sub x}:H. In the research on an a-Si:H film formed by the direct photo-CVD (chemical vapor deposition) of disilane, the unit is improved and B and P are successfully doped by means of decompressed photo-CVD. In the evaluation of new materials for solar cells, research is conducted on the after-annealing characteristics of a-Si:H grown at a high speed, electrical characteristics of post-hydrogenated low boron-doped CVD a-Si, and microcrystalline SiGe alloys made by the spattering plasma CVD method. (NEDO)

  15. Achievement report on Sunshine Program research and development for fiscal 1981. Research and development of amorphous solar cells (Optical research of electronic state in amorphous silicon); 1981 nendo amorphous silicon no denshi jotai no kagakuteki kenkyu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    The basic physical properties of glow discharge-decomposed amorphous silicon film are studied. The performance of an a-Si p-i-n (amorphous silicon positive-intrinsic-negative) junction solar cell is found to be greatly affected by the binding of carriers along the p-i or i-n interface. A new concept is introduced, which is useful in the study of the photo-produced carrier collection process. The distance between the plasma excitation center and the substrate and the intensity of the electric field just above the substrate are changed systematically for the evaluation of film quality and for the study of film formation mechanism. It is found that plasma excitation as a mechanism of film deposition, the transportation of excited seeds to the substrate, and the incorporation of film constituting atoms into the film are important. A high-speed ion beam technique is used for the analysis of impurities. In the case of a-Si or a-SiC deposition by glow discharge decomposition, metallic Sn or In is deposited along the interface and diffused into the deposited film. The diffusion is closely related to the performance of solar cells, and a 2-layer structure incorporating the merits of both ITO (indium-tin oxide) and SnO{sub 2} films is found suitable for this purpose. Using an a-SiC:H/a-Si:H heterojunction solar cell, a conversion efficiency of 8.04% is achieved. (NEDO)

  16. Achievement report for fiscal 1984 on Sunshine Program-entrusted research and development. Research and development of amorphous solar cells (Theoretical research on amorphous silicon electronic states by computer-aided simulation); 1984 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Keisanki simulation ni yoru amorphous silicon no denshi jotai no rironteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-04-01

    Research on the basic physical properties of amorphous silicon materials and for the development of materials for thermally stable amorphous silicon is conducted through theoretical reasoning and computer-aided simulation. In the effort at achieving a high conversion efficiency using an amorphous silicon alloy, a process of realizing desired photoabsorption becomes possible when the correlation between the atomic structure and the photoabsorption coefficient is clearly established and the atomic structure is manipulated. In this connection, analytical studies are conducted to determine how microscopic structures are reflected on macroscopic absorption coefficients. In the computer-aided simulation, various liquid structures and amorphous structures are worked out, which is for the atom-level characterization of structures with topological disturbances, such as amorphous structures. Glass transition is simulated using a molecular kinetic method, in particular, and the melting of crystals, crystallization of liquids, and vitrification (conversion into the amorphous state) are successfully realized, though in a computer-aided simulation, for the first time in the world. (NEDO)

  17. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and dessolution deposition process); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu (yokai sekishutsuho))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to manufacture low-cost large-area solar cell modules, developmental research has been performed on a film manufacturing technology using the dessolution deposition process. This paper summarizes the achievements in fiscal 1999. The research has been performed on a technology to form a thin silicon film directly on carbon substrates being substrates of different kinds, without using seed crystals. The researches made up to the previous fiscal year has made possible to form the film onto a substrate of about 5-cm square, has fabricated cells although with a small area, and indicated the importance of reducing concentrations of impurities in the solvent metals used. The researches performed during the current fiscal year executed modifications to reduce the temperature distribution in the substrate surfaces, including size increase in the heater, and improvement in the cooling heat conduction mechanism. As a result, films were formed successfully on 7.5-cm square substrates. In reducing the process temperatures, it was made clear that films can be formed at lower than 700 degrees C by using zinc as a solvent metal. Furthermore, the purity enhancement in the solvent metal achieved a conversion efficiency of 11.6% although the area is as small as 3.73 cm{sup 2}. (NEDO)

  18. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey and research on practical application - Volume 1); 1999 nendo taiyoko hatsauden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu - 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A 'Sub-committee for investigation of crystalline compound semiconductor solar cells' was established with the participation of experts from the industrial, bureaucratic, and academic circles to support the manufacture of ultrahigh-efficiency crystalline compound solar cells, and a survey was conducted about technical trends relating to III-V group compound solar cells. In the study of the trends and tasks of the state of the art technology, it is stated that the III-V group compound semiconductor multi-junction solar cell was steadily improving in efficiency, that the InGaP/GaAs 2-junction cell on a Ge substrate and InGaP/GaAs/Ge 3-junction cell in particular were moving toward mass production, and that the target for the 4-junction cell to achieve was 40% or higher in efficiency. For cost reduction, investigations were made into the heteroepitaxial technology, dimensional enlargement, mass production, raw material cost reduction, feasibility of the polycrystalline thin-film technology, light concentration, etc. For efficiency improvement, boundary layer control, structure designs, etc., were studied. Investigations were also conducted into nitride semiconductors, superlattice construction, etc., which related to new materials for thin films. TPV (thermophotovoltaic) power, etc., were reviewed for their practical application. (NEDO)

  19. Sunshine Program achievement report for fiscal 1981. Research and development of photovoltaic power systems (Research and development of solar cells using II-VI group compound semiconductors); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. II-VI zoku kagobutsu handotai taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    An excellent sintered film is acquired when 0.3% SO{sub 4}{sup 2-} is added to the raw material for the preparation of a CdS film starting material. A CdS film is burned at 600 degrees C, this temperature being lower than the conventional temperature (690 degrees C), and then reburned at the same temperature of 600 degrees C. The resultant device is found low in performance. For the preparation of paste for CdTe film, the material is pulverized into grains of the same size, and this stabilizes device performance. Burning temperatures are also reviewed. Carbon electrodes, Ag-In electrodes, etc., are also reviewed, and 92% of the devices produced under the currently optimum mass production conditions are found to have a conversion efficiency of 4% or higher. The best one is found to exhibit a conversion efficiency of 8.29%. In the study of the method of module constitution, the structure of cross section is improved, the manufacturing process is stabilized, and simplification is carried out. The reliability of the 5 times 10cm{sup 2} substrate device manufactured in this fiscal year is found greatly improved. It is found also that degradation it suffers is attributed to an episode occurring in the interface between CdTe and carbon. A module in which two of the devices manufactured here are connected in series is tested. It exhibits no degradation when exposed to outdoor conditions, but its conversion efficiency is substantially degraded in a moisture test. (NEDO)

  20. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Dissolution/deposition method); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (yokai sekishutsuho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to manufacture the above at low cost by a dissolution/deposition method. Under this method, a film is fabricated containing crystals high in quality and large in size though the film area is very small. In fiscal 1998, an effort to fabricate a film to cover a 10cm square substrate failed. The failure is explained by that the heater was too small for the substrate area and that the failure to uniformly heat the substrate resulted in an inplane temperature distribution greater than expected. The furnace was modified in a minor way to narrow substrate temperature distribution as much as possible. Another attempt was made to fabricate a larger-area film on a 5cm square substrate, and then crystals grew to cover approximately the whole surface of the 5cm square substrate. Efforts will continue to achieve the goal. As for the mechanism of film fabrication on substrates of different kinds, self-coating is now described by difference in heat conductivity between a carbon substrate and silicon substrate. Thanks to individual control in a small film fabricating unit, a film thickness of approximately 100 micrometers was achieved. The distance of diffusion was 30 micrometers or more in the case of a small area, and the efficiency of a solar cell using this film was found at 10.2%. (NEDO)

  1. Achievement report for fiscal 1999 on the development of silicon manufacturing process rationalizing energy utilization. Research and study on analysis to put silicon raw material manufacturing technology for solar cells into practical use; 1999 nendo energy shiyo gorika silicon seizo process kaihatsu seika hokokusho. Taiyo denchi silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In order to support the development and practical application of a mass production technology for manufacturing silicon raw materials for solar cells, research and study were performed on trends of developing the related technologies, and movements in markets and industries. This paper reports the achievements thereof in fiscal 1999. Markets for solar cells are growing favorably, and the worldwide solar cell production in 1999 was 200 MWp, of which 80% or more is occupied by crystalline silicon solar cell. While development of the manufacturing technology for SOG-Si mass-production is in the stage of operation research of pilot plants, it has been verified that problems of impurity contamination was resolved, and high-purity silicon can be manufactured. In developing the silicon scrap utilization technology and a technology to integrate silicon refinement with casting, a conversion efficiency of 14% or higher was acquired in prototype sample substrates. It has been verified that a variety of raw materials can be dealt with by using the above technology, which has a possibility of cost reduction. In developing a substrate manufacturing technology, a great progress has been made in enhancing the productivity and reducing the cost by developing the continuous casting in the electromagnetic casting and the automation technology. (NEDO)

  2. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system /development of technology to manufacture solar cells/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture silicon crystal based high-quality materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi seizo gijutsu kaihatsu, usumaku taiyo denchi seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (silicon kesshokei kohinshitsu zairyo kiban no seizo gujutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is intended to develop thin film solar cells capable of mass production with high photo-stability and at low cost. Thus, the objective of the present research is to analyze the growth process of micro crystal silicon based thin films, the crystal being a high quality silicon crystal based material, and develop technology to manufacture high-quality micro crystal silicon thin films based on the findings therefrom. It was found that, when silicon source is available in cathode, pure hydrogen plasma forms micro crystal silicon films by using the plasma as a result of the chemical transportation effect from the silicon source. It was revealed that the crystal formation due to hydrogen plasma exposure is performed substantially by the crystals forming the films due to the chemical transportation effect, rather than crystallization in the vicinity of the surface. The crystal formation under this experiment was concluded that the formation takes place during film growth accompanied by diffusion of film forming precursors on the surface on which the film grows. According to the result obtained so far, the most important issue in the future is particularly the control of crystal growing azimuth by reducing the initially formed amorphous layer by controlling the stress in the initial phase for film formation, and by controlling the film forming precursors. (NEDO)

  3. New Sunshine Project FY 1996 report on the results of development of photovoltaic power generation system commercialization technologies. Research on commercialization of the technologies for production of thin-film photovoltaic cells (Development of fabrication technologies of high-quality CuInSe{sub 2}-based thin-film solar cells); 1996 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu (kohinshitsuka gijutsu (CuInSe{sub 2} taiyo denchi seizo no gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Described herein are the FY 1996 results of development of fabrication technologies for high-quality CuInSe{sub 2}-based photovoltaic cells. The Cu-Ga alloy/In-stacked precursor film is prepared for production of the high-quality thin-film absorber applicable to large-area module fabrication, and selenized by the vapor-phase selenization in a H{sub 2}Se gas atmosphere to produce the thin light-absorbing film in which In and Ga are present at graded concentrations. Increasing Ga alloy content in the CIGS-based thin-film photovoltaic cell fails to widen the forbidden band and improve V{sub oc}, and further optimization works are needed. The method is developed for production of thin-film buffer layer of sulfur-containing Zn compound which can give the cell characteristics equivalent to those of CdS generally used for CIS-based thin-film photovoltaic cell. It is clarified that the photovoltaic cell characteristics can be improved by use of a transparent electroconductive ZnO film of stacked structure, produced by a combination of RF sputtering and DC sputtering. For the patterning technologies necessary for forming series connection on a mini-module, the laser scribing method is applicable to the metal base-electrode, and the mechanical scribing method to the light absorber and window layer. (NEDO)

  4. FY 2001 report on the results of the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Survey of the commercialization of high efficiency power generation using fuel of waste such as waste construction materials; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Kensetsu haizai tou haikibutsu nenryo ni yoru kokoritsu hatsuden no jigyosei chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    The paper studied a system for power generation and heat utilization using wood chips such as waste construction materials, used paper inappropriate for recycling and plastic refuse from neighboring local governments as fuel and assessed a potentiality of the commercialization. As to the system, the following were conducted: selection of the optimum combustor in the waste power generation, survey of the state of corrosion of boiler tube in the steam conditions and waste properties, selection of the optimum quality of boiler materials, etc. In the assessment of a potentiality of the commercialization, the commercialization was studied as in-house power generation/heat utilization business with a power generation scale of 9,950kW and a steam supply scale of 31.5t/h. As a result of the study, the energy conservation effect was found to be expected as follows: reduction of 33,000kL/y crude oil equivalent and reduction of 16,000t-CO2/y emission. As a result of studying the economical efficiency of business, the unit price of wood chip purchase and the unit price of waste plastic treatment which are required to recover the difference of the initial investment within 5 years were greatly different from the level as an aim. For the realization as business, a subsidy of 15% and more cost reduction were requested. (NEDO)

  5. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Final year report. R and D on the bio-fuel production by high functional bio-reactor; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Kokino bio reactor ni yoru bio nenryo seisan ni kansuru kenkyu kaihatsu (saishu nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A system was developed for producing automobile fuel from the recycled paper and waste cooking oil using high functional intelligent yeast. Element technology is the functional yeast creation technology and the online intelligent control technology of the process into which the fixed bio-reactor was inserted. Studies were made on the following: 1) creation of high activity lipase production/ethanol production yeasts; 2) bio-fuel production by intelligent bio-reactor; 3) process optimization control technology by fuzzy control; 4) stabilization of bio-fuel production yeast; 5) comprehensive investigational study. In FY 2000, the results were obtained as written below: development of the stable lipase coming from rhizopus japonicus, fixed bacterium using rhizopus oryzae fungus body which can be used more than ten times, direct ethanol fermentation from starch by developing the multi-copy glucoamylase manifestation yeast, operation of a 20L capacity bench plant, etc. (NEDO)

  6. FY 2001 report on the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Potential survey of the introduction of a processing/power generation system using ASR in the South region of Tochigi Prefecture; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Tochigi ken nanbu chiiki ni okeru ASR (Shuredda dust) wo nenryo to shita shori hatsuden system no donyu kanosei chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the consistent processing of waste automobile in Tochigi Prefecture and the neighboring area, survey/study were made of the thermal recycle using shredder dust, ASR (automobile shredder residue), as fuel as well as the material recycle. As to the amount of material recycle of waste automobile, the amount of potential recycle of iron, copper, plastic, etc. was estimated, and it was found out that the potential recycle of parts such as engine was 40-45%, that of iron scrap 35-40%, and that of ASR 20-25%. The amount of fuel (ASR amount) to be thrown into the gasification power generation system was set up at 150t. As the gasification power generation system, the pyrolysis gasifier and shaft kiln gasification melting furnace were selected. In the study of economical efficiency of the gasification power generation system, the following were considered: ASR processing price, plant cost, subsidy, running cost, char receiving price, power selling price, etc., but even in the case of the pyrolysis gasifier with highest valuation, both payback years and IRR did not reach the target. (NEDO)

  7. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

  8. FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of establishing the high-grade utilization technology of unused seaweed/algae and production technology of useful substances using high-grade functions of bioconsortia, study was conducted, and the FY 1999 results were reported. In the analysis of the ocean environment adaptation mechanism, the R and D were made of a selection method of the marine microbial consortia using korormicin. In the study of the high-grade utilization technology of unused resources/substances such as marine-producing algae, several tens of the carrageenase producing microbial consortia were acquired from the surface of seaweed, and some carrageenase producing bacteria and non-producing bacteria were acquired by isolating as pure strains. In the study of the petroleum substituting useful resource production technology, developed was a monitoring system of the environmental stress using marine-product invertebrate/micro-algae symbiotic system. In the study of the high-grade utilization of large useful algae, elucidation of the related genes, fabrication of variants and analysis of genes were carried out for the bacterium BUP-7 which indicates activity of growth acceleration/shape formation of seaweed. (NEDO)

  9. Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.14). Achievement report on joint research for utilizing Russia's now-unused high-viscosity crude oil as fuel for power generation; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.14). Russia miriyo konensei gen'yu no denryoku nenryo riyo kyodo kenkyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Russkoye high-viscosity oil field is located in the western part of Siberia, Russia. Joint research is under way to develop a technology for reducing the viscosity for the collection of crude oil through the utilization of a gas condensate discharged by a neighboring gas field. This report comprises eight chapters, namely, (1) the background, purpose, and contents of the research, (2) Russia's oil resources and oil industry, (3) high-viscosity oil fields in Russia, (4) analysis of Russkoye crude oil and gas condensates yielded in Russia, (5) methods for viscosity reduction, (6) evaluation of combustibility, (7) scenario for developing the Russkoye oil field, and (8) research results as summarized and future tasks. Studied in chapter (5) are approaches to viscosity reduction, methods for emulsification, and a method for viscosity reduction by use of a gas condensate. These are tested and the results after analysis clearly show that the Russkoye crude oil, when blended with a gas condensate, will turn transportable and will provide a fuel equivalent to fuel oil C. (NEDO)

  10. FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing the technology for producing and degrading useful substances using bioconsortia, study was made of the handling technology of bioconsortia, the basic element technology, etc., and the FY 1999 results were reported. In the study of the high-grade utilization technology of lignocellulose/the components, an sample was obtained in which the effect of the bacteria culture supernatant treatment was recognized in the biobleaching by co-treatment of the bacteria culture filtrate - MnP. As to the search for control factor of lignin degrading enzyme and the utilization technology, it was found out that bisphenol A was efficiently degraded by a combination of laccase and mediator production bacteria. Concerning the utilization technology of plant symbiotic bacteria, classification/identification have been finished of approximately 60% of the stored bacteria. In the study of the production technology of the petroleum substituting useful resource, a system was constructed in which immature embryos were used for callus induction and regeneration of plantlets, and plants were regenerated at high frequency via the formation of adventitious embryos. By this, the culture cell with high propagation ability was obtained. (NEDO)

  11. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research and development of high-quality amorphous silicon film formation technologies using plasma separation); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (plasma bunri ni yoru kohinshitsu amorphous silicon maku seimaku gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    When discharge plasma is applied for film formation, ions affect the quality of the resultant film. In the case of plasma CVD (chemical vapor deposition) method, there exists correspondence between the radicals ratio SiH/H and solar cell conversion efficiency, and plasma measurement may be used for the control of film formation conditions. The state of distribution of radicals in discharge plasma is dependent on the type of radicals, and there is an optimum substrate position. Photoelectric characteristics are improved when a grid electrode is used for plasma separation. The surface of a transparent conductive film (ITO: indium-tin oxide) to be the substrate for film formation needs to be flat, and part of its Si is oxidized into SiO{sub 2} by generated oxygen. An ITO film coated by chemically stable SnO{sub 2} is useful. When the ion plating method is employed, film formation conditions are first selected, and then, in a heat treatment to follow, resistance films of various surface conditions are obtained. Carbon-added a-Si film formation conditions and the relationship between film qualities and solar cell characteristics are elucidated. In a solar cell of the p-i-n structure with an a-Si:C:H film acting as the p-layer, a conversion efficiency of 7.6% is achieved. (NEDO)

  12. Achievement report for fiscal 1981 on the development of solar energy technologies for the development of practical application technologies for photovoltaic power systems. Experimental fabrication of solar cell panels and verification thereof (Development of technologies for panel assembly process); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (panel kumitate kotei no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In a study of cell array connection process, continuous and automatic connection of cells is named as the basic concept in view of low cost and high reliability. In the designing of details of cell strings, CZ (Czochralski) cell dimensions are reviewed for cell packaging efficiency improvement, interconnectors and wiring are examined for a easier packaging process, and solder connection is thought over for utility cost reduction. Conditions are established for string fabrication process details. In the study of the panel packaging process, panel package designing is carried out and a dedicated mechanical device is installed. In the study of the inspection process and plant system, data are collected, necessary for the construction and adjustment of an inspection device. Research is conducted on the layout of plant facilities, on required utilities, and on facilities operating state signals to be transmitted to the central control unit. As for an inspection jig supply system, transfer system, and storage rack, they are designed, built, and installed. The plant house is now complete. (NEDO)

  13. Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

  14. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of environmentally-friendliness enhancement for next-generation solar cell development); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Shuhen yoso gijutsu ni kansuru kenkyu chosa, Jisedai taiyodenchi kaihatsu kankyo tekioka chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Though the trends of solar cell development are becoming increasingly diverse across the world, yet none has emerged to promise a stable solar cell supply in the future. Under the circumstances, studies were conducted to clarify strategies for solar cell technology development which would be well adapted to Japan's social environments, with the trends of development in the United States and European countries taken into consideration. The surveys covered the research and development and diffusion of photovoltaic power generation in the United States and European countries, and their solar cell research and development strategies and trends of development were put together. Surveys were also conducted into the research and development of unconventional types of solar cells, such as the dye-sensitized solar cell, organic solar cell, conjugate polymer solar cell, and the polymer/C{sub 60} based solar cell, and into the status of resources of materials for solar cells such as gallium, arsenic, cadmium, tellurium, indium, selenium, and germanium. Regarding the future of photovoltaic power generation research and development, it was concluded that commercialization technology development and basic research and development should continue. Also pointed out was the importance of the enlargement of the market for photovoltaic power generation systems. (NEDO)

  15. New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to develop high-performance solar cells, optimum device designs including an advanced light confinement structure or the like were studied, and a 25% reduction in the total power generation layer thickness and a 7% increase in efficiency in power generation were consistently achieved in an a-Si/a-SiGe solar cell. In the effort to develop low-cost process technologies, as the result of studies involving the optimization of high-speed film fabrication requirements such as hydrogen dilution and a high-speed/high-precision patterning method and the like, an initial conversion efficiency of 11.2% was attained, which was the world high for a 90 cm times 90 cm-large a-Si/a-SiGe solar cell. This being equivalent to a post-stabilization efficiency of 10%, the fiscal 2000 target was achieved. A solar cell module production cost assessment was performed based on the result, and a module cost of 133 yen/W (in case of 100 MW/year production) was realized, which again meant the achievement of the fiscal 2000 target. (NEDO)

  16. Report on achievements in fiscal 1999 on research and development of immediately effective and innovative energy environment technology. Part 1. Development of immediately effective and high-efficiency solar cells, and development of technology to slice and manufacture thin-type large-area polycrystalline substrates; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (usugata daimenseki takessho kiban slice seizo gijutsu kaihatsu 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective of decreasing silicon usage quantity for the purpose of reducing the solar cell production cost, development is being performed on an ingot cutting technology to cut a silicon ingot to Kerf loss of 150 {mu} m and thickness of 150 {mu} m, and in which the produced wafers can withstand the cell making. Investigations revealed that a wire saw is suitable as the cutting system, and the wire used must have a diameter of less than 120 {mu} m, and a strength of more than 3850 N/mm{sup 2}. A prototype wire was fabricated, whose diameter is 120 {mu} m, and in which the strength is distributed between 3870 and 4110 N/mm{sup 2}. It was found possible that a wire of 160 {mu} m can be used to slice an ingot having a cross section surface of 150 mm square and a length of 300 mm into a slice having a Kerf loss of 200 {mu} m and a thickness of 180 {mu} m. This wafer had the in-plane distribution of the substrate thickness at {+-} 12.5 {mu}, swell of 120 {mu} at maximum, and surface roughness of 5 {mu}. Making ten of these wafers into a cell resulted in a yield of 60%. Assignments are the clarification of the properties of the cutting wire, the preparation of a thin wire with homogeneous quality, and the establishment of a technology to cut Kerf loss of 150 {mu} and substrate thickness of 150 {mu}. (NEDO)

  17. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of environmentally-friendliness enhancement for next-generation solar cell development); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Shuhen yoso gijutsu ni kansuru kenkyu chosa, Jisedai taiyodenchi kaihatsu kankyo tekioka chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Though the trends of solar cell development are becoming increasingly diverse across the world, yet none has emerged to promise a stable solar cell supply in the future. Under the circumstances, studies were conducted to clarify strategies for solar cell technology development which would be well adapted to Japan's social environments, with the trends of development in the United States and European countries taken into consideration. The surveys covered the research and development and diffusion of photovoltaic power generation in the United States and European countries, and their solar cell research and development strategies and trends of development were put together. Surveys were also conducted into the research and development of unconventional types of solar cells, such as the dye-sensitized solar cell, organic solar cell, conjugate polymer solar cell, and the polymer/C{sub 60} based solar cell, and into the status of resources of materials for solar cells such as gallium, arsenic, cadmium, tellurium, indium, selenium, and germanium. Regarding the future of photovoltaic power generation research and development, it was concluded that commercialization technology development and basic research and development should continue. Also pointed out was the importance of the enlargement of the market for photovoltaic power generation systems. (NEDO)

  18. New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of high-reliability CdTe solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Koshinraisei CdTe taiyo denchi mojuru no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted for reliable CdTe solar cell modules, large in area and high in efficiency. In the study of large-area CdS thin film fabrication, a conversion efficiency of 12.5-14.2% was achieved in a cell in a large-area substrate using a mist method-aided process of continuous CdS film fabrication. In the study of large-area CdTe thin film fabrication, the optimization was studied of the base-forming CdS film fabrication conditions and of the CdTe film fabrication conditions in a method using a CdTe powder processed by dry kneading, and a conversion efficiency peak was found to exist when the CdS film thickness was in the range of 700-900 angstrom. In the fabrication of large-area submodules, a large-area substrate was taken up, and TCO (transparent conducting oxide) film was fabricated by the mist method, CdTe film by the normal pressure CSS method, electrodes by the screen printing method, and CdTe film patterns by the blast method. As the result, a conversion efficiency of 11.0% was achieved. In a cost estimation for large-area CdTe solar cell modules, 140 yen/Wp (conversion efficiency: 11.0%, annual production: 100 MW) was obtained. (NEDO)

  19. New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to improve cell efficiency, experiments were conducted for enhancing bottom a-SiGe cell efficiency for the embodiment of an enhanced-efficiency multi-junction cell, for improving crystallinity in microcrystalline silicon through the application of VHF (very high frequency) plasma CVD (chemical vapor deposition), for texturizing metal electrodes on a film substrate, and so forth. In the effort to increase the film fabrication rate, a VHF plasma CVD device was used for studying the effect of the discharge frequency on film deposition and quality, Vpp between the electrodes, and so forth. Studies about the high-throughput production technology centered on the film substrate solar cell process technology and the designing of an optimum geometrical pattern for SCAF (series-connection through apertures formed on film) cells. Production cost was estimated for the SCAF structure film substrate solar cell manufacturing process, and a production cost of 147.1 yen/W (in case of 100 MW/year production) was obtained as achievable under the currently available conditions. (NEDO)

  20. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of high-quality amorphous material/substrate manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A microcrystalline Si thin film is used to form the i-layer of a narrow gap a-Si based thin film solar cell. Since a microcrystalline p-layer is to act as the seeding crystal layer for the microcrystalline i-layer, it has to be very high in crystallinity and therefore is produced under high hydrogen dilution conditions. In this process, a problem arises of the darkening of the underlying transparent SnO{sub 2} electrode. Since this is due to chemical reaction on the SnO{sub 2} surface layer, blackening is prevented by shortening the film fabrication time, and then an excellently microcrystalline p-layer is obtained. Furthermore, by inserting a microcrystalline i-film buffer layer of low fabrication rate into the p/i boundary, plasma damage on the microcrystalline p-layer is inhibited for the fabrication of a microcrystalline i-layer high in crystallinity at high film fabrication rates. A high Voc is then obtained even when the microcrystalline p-layer is very thin. If the hydrogen dilution rate is too low when the i-layer film fabrication rate is high, the initially fabricated layer turns out to be thick to the detriment of film performance. On the other hand, the p-layer or the buffer layer will be etched when the hydrogen dilution rate is too high. The problem is solved by continuously varying the hydrogen dilution rate from high to low during i-layer fabrication. (NEDO)

  1. Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of new building material integrated solar cell modules - investigation and research on analysis of practical application); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to promote the research to put new building material integrated solar cell modules into practical use, the following items were investigated: (1) functions and specifications for harmonizing with buildings, (2) new module materials that can respond to building materials, (3) marketability, (4) standardization of the assessment methods, (5) consistency with relevant legislation and related institutions, (6) effects on environment as building materials, and (7) investigation on technological trends inside and outside the country. In Item (1), the significance of developing the new building material integrated solar cell modules was made clear. In Item (2), the performance requirements on the currently used module materials were put into order. In Item (3), the market size was investigated, and assignments to establishing the market were put into order, such as the distribution and construction institutions, and assistance to the system introduction. In Item (4), standardization and unification of the assessment methods were discussed, and the items to be standardized were extracted. In Item (6), LCA on the currently used modules was performed. In Item (7), participation was made to the second solar beam power generation conference and EUROSUN '98; investigations were made on trends of developing the new building material integrated solar cell modules and how the recycling related legislation is being progressed; and the achievements in the development activities were confirmed, and the assignments were investigated at the new building material integrated solar cell module subcommittee. (NEDO)

  2. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Highly durable roof module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - kotaikyusei yane module)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A thin-film solar array, a large roof panel, and an interconnecting power conditioner are integrated into one and single structural member for the development of a residential photovoltaic power system in which a unit AC (alternating current) output is collected from each panel. In fiscal 1999, in the study of highly durable materials for solar cell modules and of their structure, a thin film compound solar cell module was enlarged to 82cm times 71cm, evaluated for performance, and installed on the third test house. In the study of collecting AC power from the solar cell module, a compact power conditioner for a roof panel which had been in test operation on the roof of the laboratory since 1998 was checked for practical performance, improved, and evaluated for system generation efficiency. In the study of a highly durable roof module structure, problems pertaining to heat radiation from the rear side steel sheet, the burning of the junction box, etc., were solved, and the module passed a verification test under the Building Standard Law. In the validation of the roof module for which power generation performance and meteorological conditions had already been continuously measured for 19 months, it was found that the roof module suffered no troubles such as water leak or deformation. (NEDO)

  3. Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - modules with new multi-layer structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (shinfukuso kozo module))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Development is being made on a panel type module that can be used together with an air bubble concrete board (ALC board), and is provided with design characteristics. The development work includes trial fabrication and evaluation of a module with new multi-layer structure, and development of a technology to unitize cells and submodules, and a systematizing method. In the trial fabrication and evaluation, flame retardant and uninflammable modules using fluororesin, and modules with as large area as 4 m{sup 2} were fabricated on a trial basis, in addition to the modules with the basic structure. These modules were given evaluations on such wall material properties as wind pressure resistance, heat and cracking resistance, and fire resistance. In a deformation resistance test considering the integrated use with the ALC board, the developed modules showed a good result. In developing the cells with design characteristics, discussions were given on the inter-cell wiring methods. Development was made on a method to establish a unit structure based on the design and size of a building. In developing the systematization method, the trial fabrication method was applied to a module with lamination structure, a module integrated with the ALC board, and a large-area hollow module to have fabricated the top-light spandrels. (NEDO)

  4. Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Formation of low-temperature film); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usukau taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (teion maku keisei gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A polycrystalline Si thin film formation technology is developed, which uses the flux process in which a reaction occurs between the target crystal and a flux component which is eutectic. Using this process, a crystal grain relatively large in diameter is obtained at a relatively low temperature. This method is now attracting attention as one of the technologies for producing crystalline Si film for use in thin-film polycrystalline Si solar cells. Especially when Al is used for flux, since Al is automatically doped into the target crystalline Si film, it is expected that the resulting film will serve as the ground for a photoactive layer provided with the BSF (back surface field) function which is important for the improvement of solar cell efficiency. A polycrystalline Si thin film is formed on a 2cm times 2cm-large glass substrate at a temperature not higher than 600 degrees C. It is recognized that films selectively oriented towards the (111) or (100) plane are acquired when other processes are employed. It is expected that the said Al-doped film provides a ground on which a BSF function-provided photoactive layer will be formed. (NEDO)

  5. Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - high-durability roof modules); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (kotaikyusei yane module))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With the target set on a system with a roof array efficiency of 8.5%, and a system cost of 170 yen/W, development is being made on a large roof panel and its construction technology, which is capable of AC output by integrating into a large roof panel the compound thin film solar cells having glass/CdS/CdTe/rear air chamber/rear metal, and the inverter. In the cell constituting materials and the structure design, sealants were evaluated, the painting process was developed, and two kinds of structures were prepared. The frameless type has a lamination structure, and a prototype module of 886 times 664 mm was fabricated, and the frame type has a double sealing structure, and a prototype module 600 times 900 mm was fabricated. Prototype modules that can be fixed on a rail type fixing stand were fabricated and constructed, having demonstrated sufficient workability. In addition, a prototype small inverter with system coordination protection was operated actually, and the initial stage malfunctions were corrected. Two demonstration buildings were built, and the whole process was performed from assembly and transportation of the modules and to the installation thereof at the construction site. (NEDO)

  6. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of amorphous silicon-based high-quality material/substrate manufacturing technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu - amorphous silicon kei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The project aims to enhance the stability of amorphous solar cells. For elevating TCO (transparent conductive oxide) substrate transmittance to an ultrahigh level and for obtaining amorphous layers less to suffer photodegradation, efforts were made to develop substrate materials stable upon exposure to plasma and low in defect density. In the study of TCO, a high-transmittance glass substrate was employed and TCO was made thinner, and the specimen achieved transmittance of 91.3% or 6.3% over that of the conventional type. In the study of low reflection films, it was found that their transmittance came to be stable and remain so after 150 days after a weatherproof test. In the study for stability enhancement, optimization was carried out for a plasma resisting Ga{sub 2}O{sub 3}-added ZnO film for the manufacture of a substrate material capable of properly behaving in a high-speed a-Si film fabrication process. Low-temperature film fabrication was studied to enable low-cost manufacturing, and it was learned that a 4 times 10{sup -4} ohm/cm low-resistance film was obtained by sputtering Ga{sub 2}O{sub 3}-added ZnO where magnetism was intensive at room temperature, that films excellent in crystallinity were obtained by the same method even at low temperatures, and so forth. (NEDO)

  7. FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for fabrication of thin-film solar cells/materials and substrates (Development of technologies for fabrication of high-quality amorphous materials and substrates); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is implemented for the amorphous/microcrystalline solar cells with the thin microcrystalline silicon film as the i layer, and the FY 1999 results are reported. The fabrication technologies are investigated for the microcrystalline silicon solar cells of pin or nip structure by RF or VHF plasma CVD using SiH{sub 4} and H{sub 2} as the stock gases. The tests are conducted for evaluating characteristics of the thin microcrystalline silicon film, to investigate the effects of film-making pressure, power and hydrogen dilution rate on the characteristics at a constant film-making temperature of 180 degrees C. The researches on the fabrication technologies for the microcrystalline solar cell of pin structure confirm that use of VHF plasma CVD improves crystallinity, electrical and optical characteristics of the p-type thin microcrystalline silicon film. The researches on the fabrication technologies for the microcrystalline solar cell of nip structure covers transparent substrates, film-making speed of the p layer, power and substrates, and a conversion efficiency of 7.5% is realized by the solar cell formed on a texture substrate. (NEDO)

  8. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development for enhancing reliability of photovoltaic power generation - Research on environmental measures for compound solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - kagobutsu taiyo denchi module no kankyo taisaku no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research is conducted to properly deal with environmental problems, such as compromised solar cell safety, which may follow the mass introduction and diffusion of photovoltaic power systems. In the research of fiscal 1999 on technical literature on environmental measures against lead and animal tests, a need was found to reduce lead in power systems and to grasp lead elution characteristics for the establishment of environmental measures. In a safety test conducted for thin-film CIS (copper indium diselenide) based solar cells, basic data were collected about the vaporization rate of Se, the effect of moisture on the Se vaporization rate, etc. Basic data were also collected about the relationship between the combustion temperature and the amount of scattered lead in particular from the solder used as the conducting material in silicon based solar cells. In the evaluation of the environmental impact of thin-film CIS solar cells in case of fire, it was found that Se concentration below 10-20m in the plume was near the permissible concentration of 0.1mg/m{sup 3} as recommended by Japan Society for Occupational Health and that the concentration levels predicted for the periphery were two orders of magnitude smaller than the mandatory level. (NEDO)

  9. Report on achievements in fiscal 1999. Research and development of immediately effective and innovative energy environment technology (Development of immediately effective and high-efficiency solar cell technology, development of high-quality ingot manufacturing technology, and development of high-efficiency cell making technology); 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (kohinshitsu ingot seizo gijutsu kaihatsu / kohinshitsu cell ka gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been made on improving quality of ingots for substrates, manufacturing high-quality thin type substrates, and making high-efficiency cells. This paper summarizes the achievements in fiscal 1999. In developing the high-quality ingot manufacturing technology, discussions were given on a method for assessing impurities and crystal defects by using the total reflection scattering type infrared tomography, and on the optimal solidifying and cooling conditions during the ingot manufacturing by using simulation calculation for solidification. As a result of analyses and discussions, such findings were found effective that the ingot should be solidified through making the solid-liquid interface shape flat, and the temperature falling rate in an ingot should be maintained constant. In developing the high-efficiency cell making technology, discussions were given on the optimal construction based on a simulation that assumes the light sealing structure using the RIE method, and on the optimal construction of polycrystalline silicon solar cells by using a device simulator (PCID). The important factors in achieving a conversion efficiency of 20% are the light sealing structure, surface passivation, and substrate thickness. (NEDO)

  10. Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects. Solar energy technology research and development; solar panel experiment, manufacture, and verification (Photovoltaic power system practical application technology; ribbon-type crystal substrate process technology); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (ribon kessho kiban kotei no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Carried over from the preceding fiscal year are the development of ribbon crystal pulling technology and the studies of ribbon crystal substrate quality and plant operation. In the development of ribbon crystal pulling process, a pulling drive is built and the limiter mechanism is strengthened for improvement on ribbon crystal flatness, technologies are established for high-speed pulling of broad ribbon crystals, pulling system prototype is built, after-annealing technique is improved for eliminating distortion, and technologies are developed for continuous feeding of raw materials. In the quality examination of ribbon crystal substrates, a method is tested and studied for bringing about a decrease in the number of SiC grains. The object of the plant operation study is a plant capable of producing 250kW-equivalent ribbon crystals a year, and the efforts involve the ribbon pulling system, rough cutter, real-size cutter, etching unit, shape checker, packing, devices for production lines such as warehouses for products, electric power, gas, water, peripheral equipment for waste water treatment etc., ribbon specifications check, quality related assistance equipment to deal with unacceptable products etc., pollution-preventing facilities for the preservation of production environments, and plant buildings. (NEDO)

  11. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture high-quality amorphous materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    These technological developments are intended to develop technologies to manufacture with improved quality the silicon-based thin film solar cells. In order to analyze manufacturing conditions for micro crystal silicon thin films as the narrow-gap amorphous silicon-based films, films were manufactured in the vicinity of borders of amorphous/micro crystal silicon film manufacturing conditions. The present film manufacturing did not present effects of suppressing deterioration of hydrogen diluted light. In order to elucidate the light deterioration mechanism in hydrogenated amorphous silicon films and study the suppression thereof, discussions were given on impurities in the film, including oxygen. By using an ultra high vacuum plasma CVD having a thoroughgoing baking system, an oil-free exhaust mechanism, and a raw material gas refining mechanism, impurities were added to and removed from a reaction vessel, and an ultra-high purity Si:H film was manufactured, which has been removed of impurities from the raw material gas, resulting in reduction of O, C and N standing no comparison. According to the result of a light irradiation experiment on an ultra-high purity film obtained under an accelerated deteriorating condition by using a pulse laser, the model assuming the light induced defect and the pair of impure atoms has been denied. (NEDO)

  12. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Novel multilayer structure module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - shinfukuso kozo module)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The project aims to develop solar cell modules of a novel multilayer structure, based on the resin filling structure, hollow structure, and the laminate structure, and integratable with building materials. In fiscal 1999, for the development of cells and submodule structures, cells and submodules were fabricated which were usable with various specimens. In the case of design oriented cells, electrode structures and linkage methods were improved for the enhancement of power generation performance, and a hollow structure and a laminate structure were fabricated. As for the 4m{sup 2}-large module (laminate structure), a specimen with dummy cells arranged along its periphery was fabricated. For cost reduction, a study was made about a module (laminate structure) integrated with an ALC (autoclaved lightweight concrete) board, and the kind of surface glass, cell arrangement, and back sheet types and their respective designs were evaluated. It was then concluded that the module was fit for practical application. The module was then checked for wind endurance in a wind endurance test, for electric characteristics, and for flame inhibition capability in a fire prevention/resistance test. (NEDO)

  13. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Volume 1. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture low-cost large-area modules and survey and research on analyzing how to put products into practical use); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu 1))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to assist research and development to put thin film solar cells for power use into practical use and a research to put thin film solar cell manufacturing technologies into practical use, survey and research have been performed on trends in the technologies inside and outside the country. Characteristic points in thin film solar cells during the current fiscal year include: expansion of production scale of amorphous silicon solar cells, rapid progress in poly-crystalline silicon thin film solar cell technologies, and enhancement of performance in large-area modules in the a-Si, CIGS, and CdTe systems. In the trends in research and development of amorphous systems, expectation is heightening on elucidation of optical deterioration phenomena, and establishment of suppression technologies thereof. Although the highest efficiency was not renewed in thin film solar cells of small areas, progress was seen in the post-stabilization efficiency in large-area modules. A thin film solar cell manufacturing plant having an annual production capacity of 20 MW was put into operation in October in Japan. Micro (poly) crystalline silicon based solar cells have high possibility of being compatible in cost reduction and performance improvement, and energetic researches are being carried out on them in recent years as the most promising candidate of the next generation solar cells. (NEDO)

  14. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Survey and research of analysis of commercialization - Separate Volume: Survey of next-generation ultrahigh-efficiency solar cell system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Jitsuyoka kaiseki ni kansuru chosa kenkyu - Bessatsu : Jisedai chokokoritsu taiyodenchi system ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the preparation of a proposition concerning future research and development, surveys and studies were conducted centering about efficiency enhancement and cost reduction for the next generation ultrahigh-efficiency solar cell system. For improving the efficiency of the crystalline compound solar cell, studies were made about the prospects of the embodiment of a 3-junction and 4-junction types and of an increase in conversion efficiency expected to realize thanks to their light condensation behavior. It was inferred that anticipation of 29-47% conversion efficiency in 1 to 4-joint cells was theoretically acceptable. Four-joint structure cell fabrication would be a challenging task but would bring about an conversion efficiency of approximately 47% thanks to enhanced light condensation capability. As for cost reduction through the use of light condensation technology, surveys of overseas trends showed that the condensation-enhanced photovoltaic power system was characteristically fit for lower-price production. As for condensation and tracking systems, studies were made about cost calculation models of organizations involved in the United States and Europe, and then it was found that cost reduction in the optical system for condensation and in the tracking mechanism would be mandatory for the achievement of 75 yen/W. (NEDO)

  15. Report on diagnosis and survey on research cooperation in the research cooperation promotion project in fiscal 1994. Research cooperation on manufacturing clean fuel for consumer use from gasified coal gas / Research cooperation on a method for pulp manufacturing of low-pollution and energy saving type by using non-wood raw materials; 1994 nendo kenkyu kyoryoku suishin jigyo 'kenkyu kyoryoku shindan chosa' hokokusho. Sekitan gas ka gas kara no minseiyo clean nenryo seizo ni kansuru kenkyu kyoryoku / himokuzaikei genryo wo mochiita teikogai shoenegata pulp seizoho ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    In solving the problems in developing technologies peculiar to developing countries, Japan will provide cooperation. This paper describes the achievements in diagnosis and survey in fiscal 1994. Development will be made on a manufacturing process for dimethylether (DME), a synthesizable and portable clean fuel, by using coal produced in China. Annual DME production of 10,000 tons will make it possible to supply 50,000 households with the fuel of one year consumption, whereas return on the construction investment and profit can be expected. At the Shanxi Coal Chemistry Research Institute, a 500 tons a year plant making DME from gasified coal gas is scheduled to begin operation. Development will be made on a pulp manufacturing technology in China, in which environmental pollution due to waste water is largely reduced, and operation cost is reduced. Application of the oxygen-alkaline evaporation and decomposition process developed in Japan will be considered, which uses non-wood raw material such as rice straw, wheat straw and megass). The raw materials are immersed continually in low-concentration alkaline solution, dehydrated, and then lignin is oxidized and decomposed by using oxygen in a continuous oxidation reactor to make the material into pulp. China uses non-wood materials as paper raw materials at 80%, whereas effects are expected in waste water pollution prevention, energy saving, resource saving and economics. (NEDO)

  16. Fiscal 1997 survey report / R and D of important region technology. R and D of technologies giving multi-functional characteristics to C/C composites (development of high-grade surface processing technology for engine members for methane fueled air craft. 1. control technology of micro structures of ultra-high temperature members); 1997 nendo seika hokokusho juyo chiiki gijutsu kenkyu kaihatsu. Fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). 1. chokoon buzai micro kozo seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing members most suitable for aircraft use engines with methane as fuel, the R and D were conducted of technology to reform surfaces and interfaces of materials. In the R and D, the paper took up carbon fiber reinforced carbon composite materials (C/C composites). In the surface control and reformation technology using the ion engineering method, etc., in the sealing processing of C/C composites, tried was the formation of a C/SiC/Si3N4 composite layer which was formed by Si3N4 much smaller in thermal expansion coefficient than SiC. Further, technologies on ion injection, thin film formation, giving of oxidation resistance/corrosion resistance, improving/giving of thermal shock resistance, etc. In the multi-functional coating formation technology such as high liability and corrosion resistance, the study was carried out of the dense composite functionally-gradient layer as thermal stress relaxation layer and the fiber reinforced layer by carbon fiber using pores. Besides, studies were made of technologies of the micro structure control combination, evaluation of ultra-high temperature resistant environmental characteristics, etc. 61 refs., 198 figs., 44 tabs.

  17. FY 2001 report on the results of the survey of the environmentally friendly type energy community project. Utilization of combustible waste as solid fuel in Shimizu City, Shizuoka Prefecture, and the wide spread sphere of municipalities (Facilities such as RDF+LNG combined use high efficiency waste power generation); 2001 nendo Shizuoka ken shimizu shi oyobi koiki shichoson ken ni okeru kanensei haikibutsu kokeika nenryo riyo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo chosa (RDF+LNG heiyo kokoritsu haikibutsu hatsuden tou shisetsu) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    Survey/study were conducted of viability of an idea of the high efficiency power generation that combinedly use RDF from the refuse generated in Shizuoka/Yamanashi/Nagano prefectures and LNG from the LNG base in Shimizu City, Shizuoka Prefecture. In the survey of raw materials for RDF, the present amount that can be supplied to RDF power generation was estimated at 280 t/d in RDF and 4,300 Kcal/kg or more in heating value. As to the RDF/LNG combination power generation, combinations of RDF200t/d + 25MW (capacity of gas turbine power generation) or RDF200t/d + 70MW seem to be appropriate. And, 30% or more of RDF power generation efficiency is made possible. In the study of economical efficiency, expenses born by local governments were calculated supposing that the difference between the unit price of power selling and that of power generation in power generation is born by RDF suppliers. As a result, the share becomes approximately 8,600-12,000 yen/refuse t in 15-year operation, and was found lower than that in the existing small-/medium-scale refuse incineration treatment. The combustion flue gas associated with the power generation business becomes approximately 300,000 Nm{sup 3}/h. The gas turbine fuel is natural gas, and RDF is good in combustibility. Therefore, the effect on the environment is expected to be small. (NEDO)

  18. Metal oxide/hydrogen battery; Kinzoku sankabutsu/suiso denchi

    Energy Technology Data Exchange (ETDEWEB)

    Kanda, M.; Niki, H. [Toshiba Research and Development Centre, Komukai, Kawasaki (Japan)

    1995-07-04

    The metal oxide-hydrogen battery consisting mainly of hydrogen storage alloy has high energy density and high volume efficiency. However, it is disadvantageous that the self-discharge takes place since the discharge capacity is lowered due to the delivery of stored hydrogen from the hydrogen electrode. This invention relates to the metal oxide-hydrogen battery consisting of hydrogen storage alloy. Hydrogen storage alloy which is composed of LaNi5 system homogeneous solid solution having an equilibrium plateau pressure of less than 1 atm at 20{degree}C is used. As a result, the battery voltage change and the self-discharge can be reduced, and the cell performance can be improved. Examples of LaNi5 system hydrogen storage alloy are ANi(5-x)Mx (A = La, Mm, and Ca, M = Al, Mn, Si, Ge, Fe, B, Ga, Cu, In, and Co). LaNi(4.7)Al(0.3) and MmNi(4.2)Mn(0.8) are preferable. 3 figs.

  19. Cell with scrolled electrodes. Uzumaki jo denkyokutai wo sonaeta denchi

    Energy Technology Data Exchange (ETDEWEB)

    Kamibayashi, M.; Morioka, Y. (Sanyo Electric Co. Ltd., Osaka (Japan))

    1990-10-03

    Non-sintered electrode plates produced by direct filling of paste state active materials in metal fiber felt type porous body are proposed recently for use as electrode plates for alkali cells and the like. Although this type of electrode plates can be produced with a simple facility because sintering process is not required, it has a shorcoming of internal short circuiting because metal fibers pass through the separator due to fuzzing of metal fiber. According to this invention, a sheet comprising metallic fibers oriented at right angles against the scrolled direction of the electrode plate is stacked on the surface of the metal fiber felt type porous body sheet when it is scrolled with the interposed separator. As the result, fibers are not bent and does not protrude from the surface of sheet to pass through the separator because each metallic fiber comprising the metallic sheet on the surface are arranged at a right angle against the direction of scrolling of the porous sheet. 2 figs., 1 tab.

  20. Solar cell driving device. Taiyo denchi kudo sochi

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, K [Shibaura Engineering Works Co. Ltd., Tokyo (Japan)

    1991-01-24

    In driving a motor by a solar cell, if the sun light is weak, the motor cannot be started because of the fact that the start-up current of the motor is more than the current needed for driving. In this invention, a current limiting circuit is placed between the solar cell and the load, whereby the current limitation by said limiting circuit is released when the detected voltage of the solar cell reached the value required for starting the load. The current limiting circuit uses a semiconductor element such as a thyrister and a transistor which general limits a current. Such a current limiting circuit is controlled by a voltage detecting circuit and is so constructed that the cell limitation is released when a specific preset volatge of the solar cell is reached. 2 figs.

  1. Solar cell element, solar cell system, and illuminating system; Taiyo denchi soshi, taiyo denchi sochi oyobi shomei system

    Energy Technology Data Exchange (ETDEWEB)

    Oka, Y. [Toshiba Laytech Co. Ltd., Tokyo (Japan)

    1997-12-12

    This invention relates to provision of a photocatalytic film on the light intercepting surface for the solar cell substrate of the solar cell element, which transmits the lights in the wavelength region longer than ultraviolet, i.e. 410nm and longer wavelength lights, and intercepts the lights in ultraviolet wavelength region. This photocatalytic film retards the decrease in the light interception by the solar cell element, and simplifies the maintenance because it oxidizes and decomposes organic matters by the less than 410nm ultraviolet ray contained in the sunlight to prevent adhesion of organic substance on the light intercepting surface of the solar cell element. In addition, decomposed dirt composition is washed away to accelerate dirt removing performance by rain waterdrop adhesion on the intercepting surface when it is used outdoors. As to this photocatalytic film, the thickness from 0.01 to 0.5{mu}m is desirable, effective phtocatalytic activity can not be expected if the thickness is less than 0.01{mu}m, and transmission factor becomes smaller if the thickness exceeds 0.5{mu}m, producing no electromotive force. TiO2, ZnO, and FeTiO3 are used as such photocatalyst. 6 figs.

  2. Achievement report for fiscal 1997 on development of practical application technology for photovoltaic power generation systems. Development of technologies to manufacture thin film solar cells (development of technologies to manufacture silicon crystal based high-quality materials and substrates / survey and research on analysis of practical application); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu / silicon kesshokei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As a plan to develop technologies to manufacture materials and substrates for thin film solar cells, it is intended to reduce defect density, enhance film forming speed, largely improve the photo-electric conversion efficiency and increase manufacturing productivity. These goals will be realized by establishing methods to control defect density, crystal particle diameters and crystallization rate in silicon crystal systems. A technology to form micro-crystal silicon-based thin films will be developed, that have superior photo-stability, and are capable of realizing low cost and mass production. Discussions will be given on a high-density plasma control technology, a fundamental property evaluation technology for micro crystal silicon thin films, and a device design simulation technology. A technology will be developed to form amorphous silicon layer on a stainless steel substrate by using the plasma CVD process. At the same time, discussions will be given on optical annealing and thermal annealing as reformation methods. Fiscal 1997 has surveyed component technologies to identify and analyze quickly and accurately the technical trends inside and outside the country, and to mass produce thin film solar cells. The Material and Substrate System Technology Subcommittee (silicon crystals) was held to deliberate the four-year development program and its progress. (NEDO)

  3. Study of fuel control strategy based on an fuel behavior model for starting conditions; Nenryo kyodo model ni motozuita shidoji no nenryo hosei hosho ni tsuite no kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, Y; Uchida, M; Iwano, H; Oba, H [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    We have applied a fuel behavior model to a fuel injection system which we call SOFIS (Sophisticated and Optimized Fuel Injection System) so that we get air/fuel ratio control accuracy and good driveability. However the fuel behavior under starting conditions is still not clear. To meet low emission rules and to get better driveability under starting conditions, better air/fuel ratio control is necessary. Now we have understood the ignition timing, injection timing, and injection pulse width required in such conditions. In former days, we analyzed the state of the air/fuel mixture under cold conditions and made a new fuel behavior model which considered fuel loss such as hydrocarbons and dissolution into oil and so on. Al this time, we have applied this idea to starting. We confirm this new model offers improved air/fuel ratio control. 6 refs., 9 figs., 3 tabs.

  4. Hydrogen battery car developed in Matsuda; Matsuda suiso nenryo denchisha wo kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    Matsuda announced that the hydrogen battery car 'Demio FCEV' was developed by the company. This new type car not only does not need an air humidifying machine, but also supplies the necessary electricity with an ultra capacitor of a large scale condenser. Its maximum output is 40 kw, the highest speed is 90 km per hour, and the accelerating time from the stop state to 40 m is about 5 seconds, the same level as a gasoline car. One time of hydrogen charging serves for 170 km running. As a hydrogen battery car, it is the third one in the world, following the DAIMURA in Germany and TOYOTA. (translated by NEDO)

  5. Methanol as moter fuel in 21 century; 21 seiki no jidosha nenryo to metanoru

    Energy Technology Data Exchange (ETDEWEB)

    Tominaga, H [Saitama Inst. of Technology, Saitama (Japan). Faculty of Engineering

    1996-02-01

    When the oil resources situation is taken into consideration, it is important to prepare now for the demand and supply situation of oil in the 21st century. The first method of the preparation is the noble-use of oil. The second method is the development and popularization of energies for transportation equipment which can take the place of petroleum. The candidates are synthetic liquid fuel, natural gas, and electricity (secondary batter). Methanol is the only synthetic liquid fuel which has the possibility of competing with petroleum both technologically and economically. By using methanol, cleaner combustion can be expected as compared with petroleum and coal. Methanol can be produced via synthetic gas not only from coal but also from natural gas, oil sand, oil shale, and biomass. From the technological point of view, innovation of quantity production technology of methanol is the first important subject. The second importance is the development of methanol vehicles and methanol fuel. Presently, methanol vehicles and fuels are in the stage of wide range and long-term verification test by running actual vehicles. 1 tab.

  6. Evaluation of PV modules integrated with roofing materials; Kenzai ittaigata taiyo denchi module no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Morizane, M.; Yagiura, T.; Nakashima, S.; Yagi, H.; Murata, K.; Uchihashi, K.; Tsuda, S.; Nakano, S. [Sanyo Electric Co. Ltd., Osaka (Japan); Ito, M.; Kurimoto, T.; Yamakawa, H.; Fujiwara, T. [Kubota Corp., Osaka (Japan)

    1997-11-25

    PV modules unified with building materials which are low in cost, easy to install and excellent in designing were developed and were evaluated in various tests. As to the basic structure of this module, seamless and unified construction with the back metal plate was adopted considering improvement in fire prevention and cost reduction. About the installation, module is easy to install by just fit connection with the frame, and easy to remove with no use of special tools. Concerning intensity and durability requested for this module, tests on reliability such as torsion strength and wind pressure resistance were conducted according to JIS standards, and it was confirmed that there were no problems. Also on the long-term durability, tests on long-term reliability were carried out by doubling test terms of the temperature/humidity cycle test, salt water resistance test, etc., and the reliability the same as that of the existing type was confirmed. In the verification test using a model house, no changes were seen in electrical characteristics and appearance, and waterproof was also favorable one and a half year after the installation. 4 refs., 7 figs., 5 tabs.

  7. Metal oxide/hydrogen secondary battery; Kinzoku sankabutsu/suiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Hosobuchi, H.; Ema, M.

    1995-12-12

    Since the shape of powder produced by crushing the hydrogen storage alloy containing rare earth element varies widely, the density of the negative electrode made by packing the alloy powder is low. As a result, the secondary battery employing this negative electrode has a small discharge capacity. This invention solves the problem. Employing the hydrogen storage alloy containing rare earth element composed of particle shape of aspect ratio, A, of over 1.0 and below 3.0 gives rise to the negative electrode with high packing density, improving the discharge capacity of the metal oxide - hydrogen secondary battery. The more the shape of powder of hydrogen storage alloy containing rare earth element is near to sphere, the higher the packing density of negative electrode made of the hydrogen storage alloy containing rare earth element becomes. The preferable aspect ratio, A, of the powder is 1.0 {le} A {le} 2.0. Such alloy powder can be produced by mechanically grinding the rare-earth-element-containing hydrogen alloy ingot, or grinding by hydration, or grinding by atomizing followed by sieving. 1 fig., 1 tab.

  8. Metal oxide-hydrogen secondary battery; Kinzoku sankabutsu-suiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Hosobuchi, H.; Edoi, M.; Katsumata, T.

    1995-06-06

    Recently, the metal oxide - hydrogen secondary battery characterized by employing the hydrogen storage alloy as the hydrogen negative electrode draws attention. However, the secondary batteries equipped with the negative electrode composed of hydrogen storage alloy powder have such shortcoming that the charge-discharge cycle life is rather short and it changes widely from battery to battery, as the hydrogen storage alloy is disintegrated. This invention solves the problem. Employing the alloy having a composition expressed as LmNi(w)Co(X)Mn(y)Al(z) (Lm = rare earth elements including La) can suppress the disintegration of hydrogen storage alloy powder during the charge-discharge cycle. In addition, controlling the oxygen content in the hydrogen storage alloy powder to 500 - 1500ppm can reduce the oxidation corrosion of the hydrogen storage alloy, resulting in suppression of its deterioration. 1 fig., 2 tabs.

  9. Both hydrogen and electricity chargeable battery; Suiso to denki de juden kanona denchi kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    Kuriyama group of the Osaka Industrial Research Institute developed a new air-metallic hydride battery that is chargeable by both electricity and hydrogen gas. The battery uses a hydrogen storage alloy as the negative pole and uses active carbon coated with platinum as the positive pole. Potassium hydroxide aqueous solution is used as the electrolyte, and a space is arranged in the negative pole for contacting and absorbing the hydrogen with a good efficiency. The key point is the development of the hydride for energy storage that can well absorbs the hydrogen gas even it is dampened by the electrolyte. And the pole is prepared by pulverized the particles of rare earth hydrogen storage alloy having the particle size smaller than 150 micron meter, forming a Ni layer for a catalyst to absorb hydrogen, adding fluorinated resin dispersant for the sake of repellency and forming a sheet. In a test running, a half of hydrogen storage capacity is realized by charging for 30 minutes. And, 0.6 V electricity of 10 mA per unit pole area of 1cm{sup 2} is continuously obtained for 17 hours during discharging. While a third electrode is formed by nickel hydroxide, the battery is chargeable and dischargeable as the same as nickel hydrogen battery. Low cost and small size can be expected by a combination of respectively prepared fuel battery with nickel hydrogen battery. (translated by NEDO)

  10. To the partnership in Kanegafuchi Chemical Industry and solar cell; Kaneka, taiyo denchi de teikei he

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    Kanegafuchi Chemical Ind. clarified that the consultation was advanced in the direction in which the business cooperates with BP Amoco Corp. in international oil majors on the solar cell business on 11 th capital. In full amount fund subsidiary of the bell pool chemistry, the solar cell making and selling company is established in the joint venture in Europe and America, Asia, when the BP Amoco Corp. does capital participation in money mosquito solar tech which is the production marketer of solar cell. The plan which develops the amorphous solar cell of low cost which the bell pool chemistry developed in the world. The consultation of the partnership is also arranging prospect in the end June, and it seems to greatly jump by uniting with the BP Amoco Corp. of the largest hand. (translated by NEDO)

  11. PV glass curtain walls; Kenzai ittaigata taiyo denchi gaiheki no kaihatsu (glass curtain wall eno tekiyo)

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T.; Iwai, T.; Ouchi, T.; Ito, T.; Nagai, T.; Shu, I. [Kajima Corp., Tokyo (Japan); Arai, T. [Showa Shell Sekiyu K.K., Tokyo (Japan); Ishikawa, N.; Tazawa, K.

    1997-12-20

    Reported in this article are PV (photovoltaic) modules now under development for integration into building walls. First of all, the power generating capability of PV modules and appropriate use of the generated power are studied, and the performance (resistance to fire or incombustibility, strength and durability, appearance and design, and dimensional standardization) that such outer wall materials are to be equipped with are determined. Next, module development, installation technique, computer graphics-aided facade designing, and real size module-using proof test are studied before installability, the power to be generated, and designs are finalized. In the development of modules, design evaluation involves the combining of various kinds of glass, solar cells, back sheets, and fillers, and the importance is confirmed of the prevention of insulation degradation around the modules. As for the methods of installation, the gasket method and aluminum sash method, etc., are tested. In the study of facade design, it is found that various expressions are possible by properly choosing gasket colors, module types, and kinds of glass to cover the openings. 1 ref., 6 figs., 3 tabs.

  12. Research on natural gas fuel injection system. Development of high-performance pressure regulator; Tennen gas yo nenryo funsha system no kenkyu kaihatsu. 1. Tennen gas nenryo funshayo no koseino regulator kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, S; Ishii, M; Takigawa, B; Makabe, K; Harada, S; Ono, H [Nippon Carburetor Co. Ltd., Tokyo (Japan)

    1997-10-01

    With the aim of further reducing the exhaust emissions of natural-gas vehicles, vigorous research and development work is under way today on multi point gas injection (MPGI) system. In this studies, a high-performance pressure regulator, which is one of the main components of this MPGI system, has been newly developed. The results showed that a significantly better accuracy of the regulated pressure level using this regulator was obtained under the wide range of operating conditions, including instantaneously greater changes of fuel flow rate. In addition, the advanced studies of gaseous fuel injectors (GFIs) would be also conducted. 4 refs., 8 figs.

  13. Technology assessment on a hydrogen fueled aircraft system; 1980 nendo suiso nenryo kokuki system ni kansuru technology assissment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This paper describes technology assessment on a hydrogen fueled aircraft system. Indispensable as technological assignments are structuring different safety systems including prevention of leakage and ignition, not to speak of developing an airframe structure that considers cryogenic and brittle nature of liquefied hydrogen. Operation related industries would be subjected to increased burdens, such as purchase and servicing of new implements and materials, but the liquefied hydrogen industry will have a chance of growing largely with wide repercussions. In the environmental aspect, the aircraft will have less CO and SOx emission in exhaust gas and lower noise than the conventional jet aircraft. Technological problems to be solved in the development include the safety of fuel tanks, safety assurance measures, and liquefied hydrogen of the required amount to be supplied easily and at low cost. To meet these requirements, noticeable progress is demanded in hydrogen manufacturing technologies. What is also required is explosion-proof safety that does not have to require crews to take special considerations in take-off and landing, not to speak of during flight. This also applies to fuel feeding and servicing on the ground. Considerations must be given that rise in operation cost should not be excessive. (NEDO)

  14. Upgrading of brown coal by slurry-dewatering; Kattan no yuchu dassui ni yoru clean kotai nenryo no seizo

    Energy Technology Data Exchange (ETDEWEB)

    Okuma, O.; Shimizu, T.; Inoue, T.; Shigehisa, T.; Deguchi, T.; Katsushima, S. [Kobe Steel, Ltd., Kobe (Japan)

    1996-10-28

    This paper describes an outline of solid fuel production process from brown coal and the investigation results of its elemental techniques. Dried coal is produced by this process which consists of a dewatering of crushed brown coal in oil-based solvent, a solid and liquid separation of slurry, and a remained oil recovery by heating. This process is characterized by the higher thermal efficiency compared with usual drying and the restraint of spontaneous combustion of product coal. It was revealed that solid fuel with low moisture, low ash, low sulfur, and suppressed spontaneous combustion property can be produced from Australian brown coal through this process. From the comparison between kerosene and fuel oil A, it was confirmed that the oil content during dewatering was smaller and the oil recovery by heating was easier by using a solvent with lower boiling point. It was also confirmed that the spontaneous combustion property can be suppressed using small amount of asphalt by solving asphalt in the solvent and adsorbing asphalt on the surface of brown coal. From these results, low rank coals including brown coal, which are difficult to use, are expected to be used as clean coal with low ash and low sulfur through this process. 2 refs., 7 figs., 2 tabs.

  15. Fabricating method of gas diffusion electrode for fuel cell. Nenryo denchiyo gas kakusan denkyoku no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Harada, H [Yokohama (Japan)

    1994-01-28

    Cation exchange film is pressure bonded by hot-pressing on an aluminium foil for the solid high polymer electrolyte fuel cell which uses the cation exchange film as the electrolyte (PEMFC), but the conditions for the hot-pressing are severe because the softening temperature of polytetrafluoroethylene used as the binder for the bonding is higher than that of the cation exchange film. This invention is concerned with a method of improving adhesion and binding between the cation exchange film surface and the electrode catalyst layer, wherein K or Na type perfluorosulfonic acid system copolymer of the same material as that used for the cation exchange film is used as the binder in preparing the electrode catalyst layer of PEMFC, and the softening temperature of the cation exchange film itself is increased to enable high temperature hot-pressing. It is desirable to use the cation exchange film with the dry film thickness from 50 to 150[mu] and ion exchange capacity from 0.83 to 1.43 milli-equivalent/g (dry resin). 1 fig.

  16. Fabricating method of gas diffusion electrode for fuel cell. Nenryo denchiyo gas kakusan denkyoku no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Harada, H [Yokohama (Japan)

    1994-01-28

    When the cation exchange film of the solid high polymer electrolyte fuel cell which uses the cation exchange film as the electrolyte (PEMFC) is bonded with the electrode catalyst layers for the anode and cathode, the hot-press conditions are severe and satisfactory bonding is hard to be achieved because the softening temperature of polytetrafluoroethylene used as the binder for the bonding is higher than that of the cation exchange film. This invention is concerned with a means of obtaining PEMFC which can generate high cell voltage, wherein perfluorosulfonic acid system copolymer solution or dispersed solution similar to that used for the cation exchange film is used as the binder when bonding carbon cloth or carbon paper coated with electrode catalyst layers for anode and cathode to the cation exchange film, setting of hot-pressing conditions is made easier, and the adhesion and bonding of the cation exchange film surface and the electrode catalyst layers are improved. 1 fig.

  17. Analysis of fuel spray characteristics for premixed lean diesel combustion; Kihaku yokongo diesel kikan ni okeru nenryo funmu kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S; Harada, a; Miyamoto, T; Akagawa, H; Tsujimura, K

    1997-10-01

    Premixed lean diesel combustion (PREDIC) makes it possible to achieve low NOx emission. It is an important factor to make the homogeneous spray formation for PREDIC. In this paper presents I the effect of the spray dispersion on emission characteristic were analyzed with the spray observation and engine test. Pintle type nozzle, which has different feature from orifice type nozzle, are used to form the hollow cone spray. As a result, the pintle type nozzle having grooves to generate the swirl flow, makes the reduced penetration in comparison with the hole nozzle under low ambient gas pressure. And it could improve THC, CO emissions at low NOx emission condition. 7 refs., 12 figs., 1 tab.

  18. Development of coal gas production technology acceptable for fuel cells; Nenryo denchiyo sekitan gas seizo gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kimura, N; Omata, K [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    In utilizing coal for high-efficiency direct power generation using fuel cells, it is necessary that coal be fed into the fuel cells after having been made into ash-free gaseous fuel. Research and development works are being carried out with an objective to develop a coal gasification furnace most suitable for fuel cells and establish a system to refine coal up to the one that can be fed into fuel cells. Fiscal 1995 has conducted investigations on coal gasification technologies, air separation technologies, and gas refining technologies as the important element technologies, and a trial design on integrated coal gasification fuel cell (IGFC) systems. This paper reports from among the above items the result of the trial design on an IGFC system using molten carbonate fuel cells. The paper describes system comparison on paths of produced gases and anode waste gas, comparison on refining processes using a wet system and a dry system, and parameter studies on oxygen concentration in gasifying agents. It was made clear that the suitable furnace is an oxygen blown coal gasification furnace, and the power generation efficiency at the system terminal can be higher than 53%. 11 figs., 6 tabs.

  19. Development of ceramic roller bush for diesel fuel injection pump; Nenryo funsha pump yo ceramics sei roller bush no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Noda, K; Kamiya, S; Fujimura, M; Tsuzuki, M [Toyota Motor Corp., Aichi (Japan); Taniguchi, K [Denso Corp., Aichi (Japan)

    1997-10-01

    Silicon nitride ceramics have been applied to roller bush for diesel fuel injection pump in order to improve the seizure resistance. It was found that ceramic roller bush made it possible to improve the seizure load by more than three times as compared to conventional metal roller bush when the kerosene was used as lubricant The ceramic roller bush proved to be durable under engine operating conditions. 6 refs., 13 figs., 1 tab.

  20. Verification test for an electric vehicle using capacitor-battery series connection for battery load levelling; Denchi no fuka heijunka no tame no kyapashita to denchi no chokuretsu setsuzoku hoshiki wo saiyoshita denki jidosha no jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    Miyaoka, K.; Takehara, J.; Kato, S. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1998-03-25

    For the prolongation of the distance that an electric vehicle (EV) can cover on a single charge and of the service life of the EV battery unit, a system is developed, in which the battery unit and the capacitor unit are connected in series for the levelling-off of battery peak loads, and the system is tested aboard a running real vehicle. Installed on the real vehicle is a battery unit that is a series connection of 20 12V-38Ah seal-type lead-acid batteries, each battery consisting of two cells connected in parallel. Driving the vehicle is a DC brushless motor capable of a maximum operation of 9000rpm. Also installed is a capacitor unit that is a parallel connection of 40 2.3V-1800F capacitors, each capacitor consisting of two capacitors connected in parallel. Findings are described below. In a 0-400m acceleration test, 22.5 seconds is recorded with the capacitor unit in operation, meaning an improvement of 0.7 seconds. The maximum speed remains unchanged at 110km/h, which agrees with the pre-calculated value. Although the battery peak load reduction rate in a 15-mode drive pattern marks 23%, the distances covered on a single charge in this drive pattern turn out to be almost the same whether the capacitor unit is in operation or not. 3 refs., 15 figs., 3 tabs.

  1. Influence of angle of inclination on power of solar module; Taiyo denchi module no keisha kakudo to shutsuryoku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, K.; Nishitani, M. [Dai Ichi University, College of Technology, Kagoshima (Japan)

    1997-11-25

    Experiment/study were conducted on the influence of angle of inclination on output of solar modules. In the experiment, changing the angle of inclination of the photovoltaic module installed on the top of school building to 0, 30, 60 and 90 degC, the global radiation on an inclined surface was measured by pyranometer equipped with the module, and at the same time output characteristics were measured by I-V curve tracer. In the I-V curve tracer, voltage, current, and output capability diagram are illustrated automatically changing bias voltage to get the maximum output. The global radiation on an inclined surface and the maximum output indicated an almost proportional relation and were expressed in a recursion method. Moreover, measurement of the global radiation is usually conducted using the amount of global radiation on a horizontal surface, and the global radiation on an inclined surface is calculated as a sum of the direct solar radiation amount and the sky solar radiation amount after determining a penetration rate by the relational equation. By calculating the global radiation on an inclined surface, it becomes possible to calculate the maximum output of photovoltaic modules by this recursion method. 1 ref., 6 figs., 1 tab.

  2. Influence of spectral solar radiation to the generating power of photovoltaic module; Taiyo denchi shutsuryoku eno taiyoko supekutoru eno eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Minaki, S.; Ishihara, Y.; Todaka, T.; Harada, K. [Doshisha University, Kyoto (Japan); Oshiro, T.; Nakamura, H. [Japan quality Assurance Organization, Tokyo (Japan)

    1997-11-25

    As to the influence of spectral solar radiation to generating power of solar cells, a study was conducted from the aspects of season, time zone, intensity of solar radiation, etc. In the study, spectral responsive variation correction coefficients were introduced as evaluation values expressing the influence of spectral solar radiation. For the spectral distribution, an all sky spectral pyranometer by wavelength was used, and data were used which were obtained in the measurement in experimental facilities of the solar techno center. Concerning solar cell relative spectral sensitivity values, used were relative spectral sensitivity values of monocrystal and amorphous standard solar cells to the short-circuit current. Spectral response variation correction coefficients are coefficients correcting variations in conversion efficiency of solar cells due to changes in the spectral distribution. The changes of spectral responsive variation correction coefficients were studied using data obtained during April 1994 and March 1996. As a result, it was found that the coefficients showed large changes in summer and small ones in winter and that amorphous solar cells indicate this trend conspicuously. 3 refs., 6 figs., 3 tabs.

  3. Development of nickel-hydrogen battery for electric vehicle; Denki jidoshayo nickel-suiso denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Research and development of battery, a main part of electric vehicle, have been promoted. Various batteries, such as lead battery, nickel-cadmium battery, nickel-hydrogen battery, lithium ion battery and so on, have been investigated for electric vehicles. Among these, nickel-hydrogen battery is superior to the others from the points of energy density, lifetime, low-temperature properties, and safety. It is one of the most prospective batteries for electric vehicle. Research and development of the nickel-hydrogen battery with higher energy density and longer lifetime have been promoted for the practical application by Tohoku Electric Power Co., Inc. This article shows main performance of the developed nickel-hydrogen battery for electric vehicle. The nominal voltage is 12 V, the rated capacity is 125 Ah, the outside dimension is L302{times}W170{times}H245 mm, the weight is 25.5 kg, the energy density is 60 Wh/kg, the output density is 180 W/kg, and the available environment temperature is between -20 and 60 {degree}C. 1 fig., 1 tab.

  4. High place working vehicles for nickel hydrogen battery powered distribution construction; Nikkeru suiso denchi kudoshiki haiden kojiyo kosho sagyosha

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    The Tohoku Electric Power Co. Ltd., in combination with the Aichi Corporation, developed a low noise and no-exhaust gas high place working vehicle that uses NiH battery as a power for lifting or falling a bucket and cutting off electric wires. It is the first in the world that the large scaled NiH battery is used in the application field other than used as a running power of an electric automobile. The main characters of the battery may be pointed out as follows. (1) It has the energy density as 2 times as a lead battery, so 2 times of working time may be obtained by the same weight battery. (2) It is maintenance-free (a periodic maintenance is necessary for a lead battery). (3) Reduction of charging efficiency caused by the heat generated during the charging can be prevented by development of a battery cooling system. (4) As the battery is low noise and no exhaust gas, it does not trouble inhabitant anytime. The new type battery has been used in the Mizusawa business office and tested there by the end of 1998. (translated by NEDO)

  5. Nickel-hydrogen battery and hydrogen storage alloy electrode; Nikkeru suiso denchi oyobi suiso kyuzo gokin denkyoku

    Energy Technology Data Exchange (ETDEWEB)

    Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1996-03-22

    Hermetically sealed nickel-hydrogen battery has such problem that the inner pressure of the battery elevates when it is overcharged since the oxygen gas evolves from the positive electrode. This invention relates to the hermetically sealed nickel-hydrogen battery consisting of positive electrode composed mainly of nickel hydroxide and negative electrode composed mainly of hydrogen storage alloy. According to the invention, the negative electrode contains organic sulfur compound having carbon-sulfur bond. As a result, the elevation of battery inner pressure due to the hydrogen gas evolution, the decrease in discharge capacity due to the repetition of charge and discharge, and the lowering of voltage after charging can be suppressed. The adequate content of the organic sulfur compound is 0.05 - 1 part in weight to 100 part in weight of hydrogen storage alloy. As for the organic sulfur compound, n-butylthiol, ethylthioethane, phenyldithiobenzene, trimethylsulfonium bromide, thiobenzophenone, 2,4-dinitrobenzenesulfenyl chloride, and ethylene sulphidic acid are employed. 2 figs., 1 tab.

  6. Hydrogen storage alloy and alkaline battery employing it; Suiso kyuzo gokin denkyoku to sorewo mochiita arukari niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1997-01-28

    The invented hydrogen storage alloy electrode is produced in the following way: The hydrogen storage alloy powder is mixed with conductive material and rubber-like elastomer. A certain amount of viscosity modifier aqueous solution such as aqueous solution of carboxymethylcellulose is added to the said mixture to prepare a mixed paste. The said paste is dried and rolled after being filled in the current collector to be held by the current collector. The rubber-like elastomer has a strong bonding force, though it is soft. Both hydrophobic and hydrophilic groups are contained in its molecule. Example of such material is a partly fluorinated or chlorinated acrylonitrile-butadiene rubber. The addition of fluorine or chlorine atom is done to its double bond. The addition of the rubber-like elastomer is controlled to 0.05 - 10 wt% of hydrogen storage alloy powder to suppress the elevation of inner-battery pressure at the time of overcharge. 2 tabs.

  7. Estimation of the charge quantity from solar cell to battery; Taiyo denchi ni yoru chikudenchi eno juden yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, K; Nishitani, M [Daiichi University, College of Technology, Kagoshima (Japan)

    1996-10-27

    In performing an experiment of running a small electric vehicle by installing solar cells in it and by charging the storage battery at a specific voltage, an estimation was made on the charge quantity to the battery for each solar altitude and inclination of a module at different hours. The solar altitude was determined at Daiichi University, College of Technology, according to the month and the time of day from a formula using day-declination and time equation of a chronological table of science. The quantity of global solar radiation was determined by resolving the solar radiation into its direct and diffuse components on the basis of the extra-terrestrial solar radiation quantity with the change in radius vector taken into consideration; and then, the global solar radiation on the inclined face was obtained from the angle of inclination and incidence. On the roof of a Daiichi University building, solar cell modules were installed facing north and south at 0{degree}, 30{degree}, 45{degree}, 60{degree} and 90{degree} each, so that a short-circuit current was measured for each differently inclined angle. As a result of the experiment, shown in an regression formula is a relation between the temperature conversion value of the maximum output of the solar cell at the standard temperature of 25{degree}C and the quantity of solar radiation on the inclined surface. Consequently, it enabled the prediction of a charging quantity, in the case of running a small vehicle with solar cells installed, from the quantity of solar radiation on the inclined surface in the clear weather. 2 refs., 4 figs., 2 tabs.

  8. Stabilized efficiency of stacked a-Si solar cell; Sekisogata a-Si taiyo denchi no anteika koritsu

    Energy Technology Data Exchange (ETDEWEB)

    Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    Different types of tests combining light and temperature were carried out in a laboratory on predicting long-term performance of stacked amorphous silicon solar cells. Cell terminals were left open, xenon was used as an irradiation light source, and cell temperature was controlled within {+-} 2 degC of the setting. The result of the experiment may be summarized as follows: with regard to the deterioration characteristics, the speed in which the efficiency changes reached a maximum within 10 hours, and thereafter the change has slowed down gradually in the case of temperature at 50 degC; in the case of 25 degC, the maximization is reached between 500 and 1000 hours; the stabilization efficiency turns out to be a pessimistic value according to the saturated value derived from an experimental expression, hence the value would have to be expressed by specifying cell temperatures, light intensities and elapsed time; the minimum value of seasonal variation may be estimated at about 85% as a pessimistic value; for recovery characteristics, the saturated value for the recovery tends to become lower as the lower the value immediately before the recovery; and if the light intensity is varied, the deterioration characteristic shifts to that at an individual light intensity. 4 refs., 11 figs., 2 tabs.

  9. On practicality of a hybrid car with solar cells; Taiyo denchi wo tosaishita hybrid car no jitsuyosei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, K; Nagayoshi, H; Kamisako, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1997-11-25

    The paper stated a development of a hybrid car which is a parallel type with gasoline engine and electric motor as driving source (connecting each according to the situation) and is also equipped with solar cells. Specifications are gasoline engine of 1200cc, induction motor of 5.5kW, lead battery of 288V and 7.2kWh, monocrystal silicon solar cells of 180W maximum output, and body weight of 1100kg. The rear wheel is driven by electric motor, and the front wheel by gasoline engine. The car is loaded with battery charge use solar cells on hood and roof. To enhance cleaning degree, 1.6kW solar cells are installed as an installed power system and used for battery charge. Even by an electric motor with output less than that of the usual electric car, harmful exhaust gas emitted in start-up can be controlled. This is because the electric motor can be used in accelerating. It was confirmed that the power required for it could be supplied by solar cells installed on the car. The hybrid car is practically useful for prevention of local air pollution. 5 refs., 4 figs., 2 tabs.

  10. Forced-circulation solar water heater using a solar battery; Taiyo denchi wo mochiita kyosei junkahshiki taiyonetsu onsuiki

    Energy Technology Data Exchange (ETDEWEB)

    Asai, S; Mizuno, T [Yazaki Corp., Tokyo (Japan)

    1997-11-25

    Optimal operation control was discussed on a forced-circulation solar water heater using solar cells not only as the power supply of a heat collecting pump, but also for controlling operation of the heat collecting pump. With this system, when the amount of power generated by solar cells reaches a sufficient level for operating the heat collecting pump, the heat collecting pump starts operation, wherein the heat collecting medium circulates in the system. The discussion was given by using simulation based on experimental expressions such as the relation expression between insolation and heat collecting medium flow rate as derived from the result of the system`s heat collecting performance test. As a result, the following conclusions were obtained: optimal insolation for activating the discussed system is from 50 to 100 W/m {sup 2}, and the heat collected within this range is within -1.5% of the collected heat amount at an optimum value; optimal activating insolation for the case of 1000 to 2000 W/m {sup 2} with low daily cumulative insolation is from 0 to 50 W/m {sup 2}, whereas the optimal activating insolation amount increases as the daily cumulative insolation amount increases; and the optimal activating insolation amount increases as water to be supplied requires higher temperature. 1 ref., 17 figs., 2 tabs.

  11. Development of a Fe-Ni battery for electric vehicle use. Denki jidoshayo tetsu nickel denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Onozuka, T.; Okuda, K. (The Tohoku Electric Power Co. Inc., Sendai (Japan))

    1993-08-11

    Development has been made on an iron-nickel battery as a low polluting electric vehicle battery that is superior in low-temperature performance to lead-acid batteries. This paper summarizes the battery. The battery uses NiOOH for positive electrodes, Fe for negative electrodes, and alkaline aqueous solution for electrolyte. The battery was manufactured in the following manners to make it suit the electric vehicle application: The iron electrode was manufactured by mixing reduced iron powder having grain sizes from 5[mu] to 6[mu] with electrolyzed iron powder with grain sizes from 20[mu] to 30[mu] in a bonding agent, and sintered at temperatures from 750[degree]C to 800[degree]C in H2 atmosphere; iron electrodes that have superior life and material utilization factor were found to have reduced iron powder ratios from 20% to 30%; the nickel electrode consists of a substrate obtained by coating metallic Ni powder on a sheet and sintering it and filling it with NiOH; the electrolyte is composed of KOH containing LiOH and KS; the separator uses a ribbed PVC porous sheet; the container is made of PP; performance evaluation tests were conducted on discharge performance, energy density, output density, temperature characteristics, charge efficiency, and cycle life; and the results of vehicle driving tests surpassed those from lead-acid batteries. 6 refs., 18 figs., 6 tabs.

  12. Forced-circulation solar water heater using a solar battery; Taiyo denchi wo mochiita kyosei junkanshiki taiyonetsu onsuiki

    Energy Technology Data Exchange (ETDEWEB)

    Asai, S; Mizuno, T [Yazaki Resources Co. Ltd., Shizuoka (Japan)

    1996-10-27

    For the purpose of satisfying demands for qualitative improvement on tapwater temperature and pressure, an indirect-type solar water heater using solar cells, in which a closed type hot water storage tank connected directly to the water supply is integrated with a solar collector, was examined for its characteristics and performance. The heat collecting medium is a water solution of polypropylene glycol, which circulates through the solar collector pump, cistern, solar collector, and heat exchanger (hot water storage tank). The results of the test are summarized below. When comparison is made between the two solar collector pump control methods, the solar cells direct connection method and the differential thermo method utilizing temperature difference between the solar collector and the hot water storage tank, they are alike in collecting heat on clear days, but on cloudy days the latter collects 5% more than the former. In winter, when the heat exchanger heat transfer area is 0.4m{sup 2} large, a further increase in the area improves but a little the heat collecting efficiency. An increase in the medium flow rate and temperature, or in the Reynolds number, enhances the heat collecting efficiency. 13 figs., 6 tabs.

  13. Solar cell array for driving MOS type FET gate. MOS gata EFT gate kudoyo taiyo denchi array

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, S; Yoshida, K; Yoshiki, T; Yamaguchi, Y; Nakayama, T; Owada, Y

    1990-03-12

    There has been a semiconductor relay utilizing MOS type FET (field effect transistor). Concerning the solar cells used for a semiconductor relay, it is required to separate the cells by forming insulating oxide films first and to form semiconductor layers by using many mask patterns, since a crystal semiconductor is used. Thereby its manufacturing process becomes complicated and laminification as well as thin film formation are difficult, In view of the above, this invention proposes a solar cell array for driving a MOS type FET gate consisting of amorphous silicon semiconductor cells, which are used for a semiconductor relay with solar cells generating electromotive power by the light of a light emitting diode and a MOS type FET that the power output of the above solar cells is supplied to its gate, and which are connected in series with many steps. 9 figs.

  14. Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (high-efficiency III-V tandem solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (III-V zoku kagobutsu handotai taiyo denchi no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development of III-V compound semiconductor solar cells in fiscal 1994. (1) On development of epitaxial growth technology of lattice mismatching systems, the optimum structure of InGaAs strain intermediate layers was studied for reducing a dislocation density by lattice mismatching of GaAs layer grown on Si substrate and difference in thermal expansion coefficient. The effect of strain layer on dislocation reduction was found only at 250dyne/cm in strain energy. Growth of GaAs layers on the Si substrate treated by hydrofluoric acid at low temperature was attempted by MBE method. As a dislocation distribution was controlled by laying different atoms at hetero-interface, the dislocation density of growing layer surfaces decreased by concentration of dislocation at hetero-interface. (2) On development of high-efficiency tandem cell structure, tunnel junction characteristics, cell formation process and optimum design method of lattice matching tandem cells were studied, while thin film cell formation was basically studied for lattice mismatching tandem cells. 45 figs., 8 tabs.

  15. Technological development for super-high efficiency solar cells. Technological development for super-high efficiency singlecrystalline silicon solar cells (super-high efficiency singlecrystalline Si solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (chokokoritsu tankessho silicon taiyo denchi cell no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development of super-high efficiency singlecrystalline silicon solar cells in fiscal 1994. (1) On development of high-performance light receiving layer, the fine electrode for receiving surfaces was designed to reduce serial resistance, and the high-quality oxide passivation film was studied to reduce surface recombination velocity. (2) On development of forming technology of back heterojunction, the high-quality cell with B-doped fine crystalline Si film on its back was studied by heat treatment of the fine crystalline Si film, and the cell structure with high back reflectance of light was also studied. (3) On analysis for high-efficiency cells, the relation between the back recombination velocity at the interface between p-type substrate and back passivation film, and the internal collection efficiency as probe light was injected from the back, was calculated by numerical simulation. As a result, the cell back recombination velocity could be evaluated by measuring the spectral internal collection efficiency to back injection. 15 figs., 6 tabs.

  16. NEDO fuel/storage technology subcommittee. 18th project report meeting; NEDO nenryo chozo gijutsu bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Taro Yamayasu, a NEDO (New Energy and Industrial Technology Development Organization) director, reports fuel and storage technologies, taking reference to the research and development of technologies relating to fuel cell power generation, cell power storage system of a novel type, ceramic gas turbine, superconductor-generated power application, wide-area energy utilization network system (urbane eco-energy system), high-temperature superconductor-supported flywheel power storage, demonstration of a novel method of load levelling, demonstration test for the establishment of a centralized control system, and so forth. Reported also is research and development involving a molten carbonate fuel cell power generation system, current status of distributed cell power storage system development (large lithium secondary storage battery technology development), current status of superconductor-generated power application technology, regenerative cycle type 2-shaft ceramic gas turbine for a 300kW-class cogeneration system, high-density latent heat transportation, and so forth. (NEDO)

  17. Design of hydroprocessing catalyst for the production of ultra clean fuels. Super clean nenryo wo mezashita jushitsu tanka suiso seisei shokubai no kokinoka

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, Hiromichi (National Chemical Lab. for Industry,Tsukuba, (Japan))

    1990-02-01

    In order to develop high function catalyst for the ultra clean fuel refining and other purposes, the catalyst was studied in correlation between the function and structure. Hydrogenation power of aromatic ring and hydrogenolysis power of carbon-carbon bonding, which are principal functions of catalyst in the hydrogenation refining, were evaluated with model material. 30 kinds of catalyst were figure shown in classification result of evaluation. As for the mutual operation of molybdenum and carrier, it is necessary for molybdenum sulfide to be highly dispersed on carrier in order to heighten the hydrogenation activity. While the hydrogenolysis activity, as necessitating electrically negative molybdenum type to be formed on carrier, is manifested by the formation of Bronsted acidity point with hydrogen sulfide, adhering thereto. As for the molybdenum sulfide catalyst, mainly hydrogenation activity point, in case that structure, similar to molybdenum disulfide, is dispersed as a single layer on carrier, and hydrogenolysis activity point, in case that it forms a multi-layer structure thereon, are formed in edge part of respective crystal. The lowering in activity under a long time sevre condition, which mainly are carbonic material deposition, matallic adhesion, etc., is also influenced by the structural change in catalyst. 10 refs., 5 figs. 2 tabs.

  18. Effects of fuel and air mixing on WOT output in direct injection gasoline engine; Chokufun gasoline kikan ni okeru nenryo to kuki no kongo to shutsuryoku seino

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T; Iriya, Y; Naito, K; Mitsumoto, H; Iiyama, A [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The effects of in-cylinder charge motion and the characteristics of the fuel spray and piston crown shape on WOT output in a direct injection gasoline engine are investigated. The fuel and air mixing process in a cylinder is analyzed by computer simulation and LIF method visualization. As a result, the technical factors to achieve enough mixing in a DI gasoline engine equipped with bowl in piston optimized for stratified combustion are clarified. 7 refs., 9 figs., 1 tab.

  19. Numerical simulation of fuel sprays and combustion in a premixed lean diesel engine; Kihaku yokongo diesel kikan ni okeru nenryo funmu to nensho no suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, T; Harada, A; Sasaki, S; Shimazaki, N; Hashizume, T; Akagawa, H; Tsujimura, K

    1997-10-01

    Fuel sprays and combustion in a direct injection Premixed lean Diesel Combustion (PREDIC) engine, which can make smokeless combustion with little NOx emission, is studied numerically. Numerical simulation was carried out by means of KIVA II based computer code with a combustion submodel. The combustion submodel describes the formation of combustible fuel vapor by turbulent mixing and four-step chemical reaction which includes low temperature oxidation. Comparison between computation and experiment shows qualitatively good agreement in terms of heat release rate and NO emission. Computational results indicate that the combustion is significantly influenced by fuel spray characteristics and injection timing to vary NO emission. 10 refs., 8 figs., 1 tab.

  20. Effect of fuel composition on poly aromatic hydrocarbons in particulate matter from DI diesel engine; Particulate chu no PAH ni oyobosu nenryo sosei no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, S; Tatani, T; Yoshida, H; Takizawa, H; Miyoshi, K; Ikebe, H [COSMO Research Institute, Tokyo (Japan)

    1997-10-01

    The effect of fuel composition on poly aromatic hydrocarbons (PAH) in particulate matter from DI diesel engine was investigated by using deeply desulfurized fuel and model fuel which properties are not interrelated. It was found that the deeply desulfurized fuel have effect on reducing PAH emissions. Furthermore, it was suggested that poly aromatics in the fuel affect PAH emissions and the influence of tri-aromatics in the fuel was promoted by the coexistence of mono-aromatics or naphthene. PAH formation scheme from each fuel component was proposed by chemical thermodynamic data. 4 refs., 8 figs., 3 tabs.

  1. Soot and NOx simultaneous reduction by use of CO2 mixed fuel; Ekika CO2 yokai nenryo ni yoru diesel kikan no susu, NOx no doji teigen

    Energy Technology Data Exchange (ETDEWEB)

    Senda, J; Yokoyama, T; Ikeda, M; Fujimoto, H [Doshisha University, Kyoto (Japan); Ifuku, Y [Kubota Corp., Osaka (Japan)

    1997-10-01

    We propose the new fuel injection system by use of diesel fuel dissolved with CO2 to reduce both soot and NOx simultaneously. In this paper spray combustion characteristics of CO2 mixed fuel is reported. It is revealed that flame temperature and KL factor at the CO2 mixed fuel combustion are lower than at the only n-tridecane combustion due to separation or partly flashing of CO2component. And the result of exhaust gas measurement shows the capability that CO2 mixed fuel is able to reduce both soot and NOx simultaneously. 12 refs., 7 figs., 1 tab.

  2. Improvement of lean combustion characteristics of heavy-hydrocarbon fuels with hydrogen addition; Suiso tenka ni yoru kokyu tanka suisokei nenryo no kihaku nensho no kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Sakai, Y. [Saitama Institute of Technology, Saitama (Japan); Ishizuka, S. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1999-09-25

    The Lewis numbers of lean heavy-hydrocarbon fuels are larger than unity, and hence, their flames are prone to extinction in a shear flow, which occurs in a turbulent combustion. Here, propane is used as a representative fuel of heavy-hydrocarbon fuels because the Lewis number of lean propane/air mixtures is larger than unity, and an attempt to improve its combustion characteristics by hydrogen addition has been made. A tubular flame burner is used to evaluate its improvement, since a rotating, stretched vortex flow is established in the burner. The results show that with' hydrogen addition, the fuel concentration, the flame diameter and the flame temperature at extinction are reduced and its combustion characteristics are improved. However, it is found that the effective equivalence ration at extinction cannot become so small as that of lean methane/air mixture, which has a Lewis number less than unity. (author)

  3. Effect of oxygenated fuel on premixed lean diesel combustion; Kihaku yokongo diesel nensho ni oyobosu gansanso nenryo kongo keiyu no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

    1998-05-01

    Because injection timing in diesel engines is early in a premixed lean diesel combustion system using early fuel injection, ignition timing is determined by ignitability of the fuel used. The conventional diesel fuel, which has good ignitability, causes excessively early ignition, thus aggravating fuel consumption. In order to reduce cylinder temperature with an aim of delaying ignition timing to improve the fuel consumption, attempts are being made on using low cetane fuels to reduce CO2 gas supply or compression ratio, and to vary ignitability of the fuels. The present study investigated ignition timing control and properties of exhausts by mixing different types of oxygenated fuels into light oil. Mixing the oxygenated fuels into light oil proved that the ignition timing can be controlled, and mixing such low cetane fuels as ethanol and MTBE achieved improvement in fuel consumption. Trial use of the oxygenated fuels aggravated CO concentration, which is caused because the cylinder temperature was reduced. Numerical calculations suggest that use of fuels with faster evaporation speed and lower cetane number is effective in improving the fuel consumption and the exhausts. 12 refs., 9 figs., 2 tabs.

  4. Study of fuel spray characteristics for premixed lean diesel combustion; Kihaku yokongo diesel kikan ni okeru nenryo funmu keisei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

    1998-05-01

    A study is being made on premixed lean diesel combustion (PREDIC) by means of early fuel injection in diesel engines. The PREDIC makes it possible to largely reduce NOx emission, but has such problems as ignition control and increase in THC and CO generation. In order to clarify the relationship between fuel spray characteristics in the PREDIC and properties of gas mixture and exhausts, the present study has investigated spread and internal structure of the spray by means of spray observation experiment using a pintle swirl nozzle. Based on the result therefrom, simulations were used to investigate effects of spatial dispersion characteristics of the spray on properties of the gas mixture and exhausts before ignition. The pintle swirl nozzle forms conical spray having an air layer inside the spray, where penetration is suppressed even under low atmospheric pressure. By forming hollow spray or solid spray in the conical spray, a possibility was indicated that equivalent ratio distribution of the gas mixture can be controlled and NO emission may be reduced. 8 refs., 12 figs., 1 tab.

  5. Cavitation characteristics of multihole diesel-fuel nozzles in high-speed oil flows. Diesel kikan yo nenryo tako nozzle no abura cavitation tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yokota, M. (Shimonoseki Univ. of Fisheris, Yamaguchi (Japan)); Ito, Y. (Hachinohe Inst. of Tech., Aomori (Japan)); Aoki, H. (Xexel-Gleason U.S.A. Inc., New York (U.S.A))

    1991-07-25

    Recently, since higher velocity and higher pressure are required for diesel injection systems, cavitation behaviors in high velocity oil flows are strongly interested in such as 100 to 500 m/s for oil flow velocity and less than the cavitation factor {sigma} of 0.01. In this paper, oil cavitation characteristics at the injection part of multihole nozzles, especially on the flow characteristics, were studied systematically using fuel injection multihole nozzles for an actual use. As a result, it was clarified that subcavitation area (sub C), transition area, and supercavitation area (SC) could be existing in C{sub d}-{sigma} relation, which was similar to that specified cavitation conditions could be exisiting in the actual working area of multihole nozzles. And it was also clarified that flow coefficient C{sub d} relied on Reynolds number R{sub e} in the transition of {sigma}{ge}{sigma}{sub cr} and in {sub C} area, and mainly relied on {sigma} in SC area of {sigma}<{sigma}{sub cr}. Moreover, it was also confirmed that such tendency was similar to the one of the two-dimensional contraction of an area. 22 refs., 10 figs., 1 tab.

  6. Study of recent fuel oil cost in air lines (Part 2). Saikin no airline no nenyuhi ni kansuru ichikosatsu (2); Nenryo shohi to hiyo tai koka

    Energy Technology Data Exchange (ETDEWEB)

    Tanabe, Yoshikazu.

    1989-03-01

    Through an arrangement of published data about American air lines during 1985 through 1987, the overall expense vs. transportation fee (expense vs. effect) was studied as a main viewpoint. As a result, the fuel oil cost, even in case of wide fuselage plane, high in transportation efficiency, was high in ratio, 32 to 52% (3 to 5 times as high as that 12 to 14 years ago), and fluctuated connectedly with the oil price. While the jet fuel price fluctuated connectedly with the oil price per equal volume with 1.3 to 1.4 of price ratio. Further, the flight range ratio was recorded to be approx. 0.06 to 0.24 km/kg. While the transportation efficiency was lower than approx. 5000kg*km/kg with a wide range of overall expense, approx. 9 to 87 cents per compensative transportation ton*km. Because even a sudden decrease in transportation quantity did not decrease the overall expense, it was known to be important in management to secure the transportation quantity. 30 refs., 15 figs., 1 tab.

  7. Analysis of output characteristics of PV modules under natural sunlight; Shizen taiyokoka ni okeru taiyo denchi module shutsuryoku tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Murai, Y.; Igari, S. [Japan Quality Assurance of Organization, Tokyo (Japan)

    1997-11-25

    The paper measured current/voltage characteristics of various PV modules under natural light and analyzed various characteristics such as generated output and module power generation efficiency. In the experiment, installing various PV modules at the solar techno center located at north latitude 34.7deg and east longitude 137.6deg, measurement was made by I-V curve tracer, pyranometer, and thermocouple buried on the module back. As a result, the following were confirmed: As to the monthly mean power generation efficiency, the crystalline system is lowest in summer and highest in winter, and the amorphous system highest in summer and lowest in winter. Concerning the power generation efficiency and illuminance, the gap of power generation efficiency between at high illuminance and at low illuminance is large in the crystalline system and small in amorphous system. Relating to the azimuth angle of module installation and the generated output, the installation inclined 15deg angle west in summer and 15deg angle east in fall/winter generates more power in the crystalline system. On the contrary, the installation on the south face generates more power in the amorphous system. 4 refs., 8 figs., 3 tabs.

  8. Study of installation of PV systems at campus; Campus ni okeru taiyoko hatsuden donyu ni kansuru kenkyu (taiyo denchi nomi wo secchishita baai no yobi kento)

    Energy Technology Data Exchange (ETDEWEB)

    Tsuboi, N.; Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1997-11-25

    In terms of energy consumption, environmentality and economical efficiency in the case of installing the photovoltaic power system on the rooftop of the university campus, a comparative study was conducted with other power generation systems. As objects to be comparatively studied, selected were the all-electric type centralized space heating/cooling system, cogeneration system, nighttime heat storage system and centralized system with solar cells installed. The panel area of the PV system is 10,000m{sup 2} on the rooftop and 7,000{sup 2} on the outer wall. About data on solar radiation, average values obtained in Nagoya were used. Assessment was made in terms of energy consumption amount at the time of operation, system COP, emission amounts of CO2, NOx and SOx at the time of manufacturing and operation, initial cost, running cost, etc. As a result of the study, an effect of reducing global warming gas was admitted in the PV system. However, the initial cost of the solar cell panel was high, and the life cycle cost of the PV system was lower than other systems. 1 ref., 7 figs., 3 tabs.

  9. Method for estimation of the spectral distribution that influence electric power of PV module; Taiyo denchi shutsuryoku ni eikyo wo ataeru bunko nissha bunpu no suiteiho

    Energy Technology Data Exchange (ETDEWEB)

    Yamagami, Y.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    A method was proposed for estimating the spectral distribution using air mass, precipitable water, and clear indexes which are generally obtainable, and a comparative study was made between the spectral distribution obtained by this method and the measured data using output power of PV modules, etc. as indexes. When solar light comes into the atmosphere, it dissipates receiving scattering/absorption by various gases and aerosols. Direct light component and scattered light component which arrive at the earth surface become functions of air mass and precipitable water. The wavelength distribution of scattered light in cloudy sky is not dependent upon air mass, but affected strongly by absorption band by steam of clouds. By relational equations considered of these, output power and short-circuit current of PV modules are obtained to make a comparison with the measured data. As a result, it was found that this method estimated the spectral distribution with accuracy. Further, seasonal changes in the spectral distribution were well reproduced. The simulation of the module output in Sapporo and Okinawa brought a result that the output in Okinawa is 1.93% larger than in Okinawa. 5 refs., 5 figs., 6 tabs.

  10. Development of sealed nickel-cadmium battery for linear motor car (Maglev). Linear motor car yo Ni-Cd denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kono, K; Yoshimura, H; Yufu, H [Yuasa Corp., Osaka (Japan)

    1993-10-29

    Development was made of a linear motor car use battery which is strong in repetition of quick charging/discharging and characterized as follows: Its volumetric energy density is 42Wh/kg which is 1.3 times as high as the conventional one. It excels in high efficiency charging/discharging characteristics. High tension steel sheet is used for it, which is incombustible. To lighten the weight, paste type electrodes and high yield point materials were used for the positive and negative electrodes, and jar materials, respectively. To heighten the charging/discharging characteristics, used were electrodes heightened in current collecting effect. To lengthening the life, unwoven nylon cloth was used as a separator. Also to heighten the thermal discharge characteristics, the electrodes were made metallic with a fitting of cooling fins. The battery characteristics as tested gave the following result: At a capacity ratio of 100%, the discharging factor cleared its target value of development also with a high discharging voltage. The charging/discharging characteristics hardly fall in the high temperature region. The charging characteristics include quick charging made possible. As a result of cyclic simulation presuming the linear motor car, the fall in capacity per cycle was as good as 1.5%. 11 figs., 2 tabs.

  11. Hydrogen storage alloy electrode and the nickel-hydrogen secondary battery using the electrode; Suiso kyuzo gokin denkyoku to sorewo mochiita nikkeru/suiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1997-02-14

    With respect to the conventional nickel-hydrogen secondary battery, pulverization of the hydrogen storage alloy due to repetition of charging-discharging cycles can be prevented by using a fluorocarbon resin as a binder in manufacture of the hydrogen storage alloy electrode; however, the inner pressure increase of the battery in case of overcharging can not be fully controlled. The invention relates to control of the inner pressure increase of the nickel-hydrogen secondary battery in case of overcharging. As to the hydrogen storage alloy electrode, the compound comprising the hydrogen storage alloy powder as a main ingredient is supported by a current collector; further, the compound particularly comprises a fluororubber as a binder. The nickel-hydrogen secondary battery equipped with the hydrogen storage alloy electrode can control the inner pressure increase of the battery in case of overcharging, and lessen decrease of the battery capacity due to repetition of charging-discharging cycles over long time. The effects are dependent on the use of the fluororubber as a binder which has good flexibility, and strong binding capacity as well as water repellency. 1 tab.

  12. Study on hydrogen storage alloy for NiMH EV battery; EV yo NiMH denchi no suiso kyuzogokin ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kanemoto, M.; Tanaka, T.; Furukawa, K.; Watada, M.; Oshitani, M. [Yuasa Corp., Osaka (Japan)

    1998-10-30

    We have developed a high performance hydrogen storage alloy (MH alloy) suited to NiMH batteries for EV use. During the course of the development, the effects of alloy composition and structure (B/A ratio in AB{sub 5}) on cycle life and high-rate discharge of MH electrodes were investigated using mainly SEM, XRD, TEM analysis. It was found that Co content and B/A ratio (5.1/5) of MH alloy have significant effects on corrosion resistance and high-rate discharge at low temperature. Further, the surface treatments of MH alloy with weak acids and hydrophobic agents were effective for improving the initial activation and for depressing the cell internal pressure build-up. (author)

  13. Hydrogen storage alloy for battery, manufacturing method and nickel-hydorogen secondary battery; Denchiyo suiso kyuzo gokin, sono seizo hoho oyobi nikkerusuiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Inaba, T.; Sawa, T.; Inada, S.; Kawashima, F.; Sato, N.; Sakamoto, T.; Okamura, M.; Arai, T.; Hasimoto, K.

    1997-04-08

    The invention relates to a hydrogen storage alloy for a battery which has a high electrode capacity, and particularly can realize a long battery life. The hydrogen storage alloy of the LaNi5 type with the general formula: ABx is used in the invention. Here, A comprises La, Ce, Pr and Nd, and La and Nd in A account for 70 to 90 wt % and less than 5 wt %, respectively; B is at least one of the elements selected from Ni, Co, Fe, Cr, Mn, Cu, Al, Ga, Si, Ge, Bi, Sn, In, P, V, Nb, Ta, Mo and W; x shows the atomic ratio in the range, 4.5{<=}x{<=}5.6. Since rare earth elements constituting the alloy, and types and compositions of the elements substituting Ni are properly determined, the hydrogen storage alloy for a battery with excellent hydrogen storage characteristics and corrosion resistance is obtained. When the alloy is used as an anode material, the battery capacity is expanded, the alloy pulverization and deterioration are prevented. 3 figs., 1 tab.

  14. Prismatic lithium/thionyl chloride cells, EP series''. Kakugata enka thionylter dot lithium denchi EP series''

    Energy Technology Data Exchange (ETDEWEB)

    Kogure, M.; Ide, M.; Mizutani, M. (Japan Storage Battery Co. Ltd., Kyoto (Japan))

    1990-06-25

    This paper reports on a new type lithium-thionyl chloride cell of high safety. Its structure and characteristics are summerized as follows: first, a porous solid of carbon black, that is the positive electrode, including electrolyte solution of SOCl {sub 2} occupies central part of the interio of a prismatic case made of a stainless steel plate, that is the negative electrode, and a thin plate of lithium covers the inner surface of the steel plate, a glass fibre layer being placed in between the lithium plate and the carbon black solid; second, the cell continues to discharge at constant voltage (3.6V) until its life finishes, for instance, for over 10 years when connected to a risistor of 150k {omega}, third, the cell is effectively used at temperatures between {minus} 55 and 85 centigrade; fourth, the cell is preserved for a long duration without scarcely suffering in its efficiency, its capacity decrea-sing at the rate of 0.5 - 1.0% per year; fifth, the cell does not burst, catch fire or explode even if it is short-circuited, swing violently and then fallen from a height of 1.9m to concrete floor, crushed and, in particular, heated in various ways (it is so de-vised that SOCl {sub 2} vapor escapes through the glass seal adjacent to the positive terminal at temperatures about 160 centigrade). 2 refs., 10 figs.

  15. Shunt and series resistance of photovoltaic module evaluated from the I-V curve; I-V tokusei kara hyokashita taiyo denchi no shunt teiko to chokuretsu teiko

    Energy Technology Data Exchange (ETDEWEB)

    Asano, K; Kawamura, H; Yamanaka, S; Kawamura, H; Ono, H [Meijo University, Nagoya (Japan)

    1997-11-25

    With an objective of discussing I-V characteristics when a shadow has appeared on part of a photovoltaic module, evaluations were given as a first stage of the study on saturation current, shunt resistance and series resistance for the solar cell module. As a result of measuring change in amount of power generated in a sunny day with a shadow appearing over the solar cell module, reduction in power generation capability of about 23% was verified. In other words, the I-V characteristics of the solar cell module change largely because of existence of the shadow caused on the module. The I-V characteristics curve may be expressed and calculated as a function of the shunt resistance and series resistance. By curve-fitting measurement data for a case of changing insolation without existence of partial shadow, values of the shunt resistance and series resistance were derived. As a result, it was found that the calculations agree well with measurements. It was made also clear that each parameter shows temperature dependence. 6 refs., 10 figs., 1 tab.

  16. Temperature dependence of the early degradation in a-Si solar cells; Amorphous Si taiyo denchi no shoki rekka no ondo izonsei

    Energy Technology Data Exchange (ETDEWEB)

    Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    Discussions were given on early degradation in up to about ten minutes in amorphous silicon solar cells. The experiment has used a model cell of single junction layer for power use with a Glass/ITO/P-i-n:a-Si/Al structure. Test samples were annealed at 130 degC for 30 minutes to eliminate hysteresis of degradation during storage. Xenon was used as an irradiation light source, and the temperatures were varied from 0 to 100 degC and the measurement time was set to 0.1 to 500 minutes. The result of the experiment may be summarized as follows: with regard to time-based degradation pattern for conversion efficiency, the tilt of a pattern to express degradation rate varies with temperature conditions, and changes in 10 to 20 minutes of light irradiation as a boundary; in long-term degradation after 20 minutes, the higher the environmental temperature, the lower the degradation is suppressed, but the rate of initial degradation up to about 10 minutes is higher as the higher the temperature; and the degradation rate increases as the higher the temperature in the initial degradation of about 10 minutes, whereas, corresponding to this fact, it is estimated that a phenomenon is involved, in which carrier recombination defect may increase. 4 refs., 7 figs., 1 tab.

  17. Concentration characteristics and cell arrangement in luminescent concentrator PV modules; Keiko shukogata taiyo denchi module no cell haichi to shuko tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Inamura, A [Science University of Tokyo, Tokyo (Japan); Sakuta, K [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    A luminescent concentrator PV module requires no tracking equipment and can use scattered light. A mini PV module was prepared from a luminescent plate of 100times100times3mm, and a single-crystalline PV cell of 100times20mm. Characteristics of various prototype modules with different PV cell areas and cell arrangements were also measured. Four kinds of edge reflecting materials with different reflectances by various white coating were applied to Al sashes for module frames, and each sash was fixed on one edge of the luminescent plate. In experiment, 3 other edges were covered with black tapes to reduce each reflectance to 0%. Although PV module output was affected by reflectance of edges, the output was satisfactory at 90% or more in reflectance showing no difference in output. A concentrating efficiency decreased with an increase in luminescent plate (concentrator) area, while it was improved by cell arrangement with short optical pass length, and cell arrangement hardly affected by edge reflection. 4 refs., 7 figs.

  18. Control method for light deterioration of amorphous solar cell. 2. Temperature effect method; Amorphous taiyo denchi no hikari rekka yokuseiho. 2. Ondo kokaho

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H; Itsumi, J; Sano, N [Kumamoto Institute of Technology, Kumamoto (Japan)

    1997-11-25

    Experimental studies have been carried out on suppressing early deterioration in amorphous silicon solar cells. The amorphous silicon solar cell is characterized by deterioration due to light irradiation and restoration due to temperature rise. An exposure experiment was performed under three conditions: installation in natural environment, installation with rear side of the solar cells covered with an insulating material, and installation with rear side of the solar cells covered with warming elements and an insulating material. Tests were made on suppressing progress of the early deterioration caused by temperature conditions. As a result, the efficiency in the natural condition was found to decrease as largely as 32% in an open circuit condition and 58% in a short circuit condition. The efficiency reduction rate was smaller in the open circuit condition when the insulation material was installed, but in the short circuit condition, resistance characteristics caused by rain water and electrolytic corrosion were exhibited. For the case with warming elements installed, the reduction in the efficiency was more remarkable, contrary to the expectation. The cause was determined that water existing between the rear side and the warming elements was warmed up, accelerating the electrolytic action, and resulting in deterioration advanced over a wide area in the rear side. 6 refs., 6 figs., 3 tabs.

  19. Sony Co., Ltd.: An outlook is made for merchandising of the manganese acid lithium ion battery; Mangansan richiumuion denchi no shohinka ni medo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    Sony Co., Ltd. sells the manganese acid lithium ion battery that a battery is 1 by 2 as to the next generation lithium ion during 99 years. It is characteristics that a price is restrained because manganese is used for the proper pole material instead of cobalt of the rare metal. It becomes mass production by Koriyama factory where a lithium ion battery is being manufactured improving an existent production line. It is seen when some percents of manufacture cost goes down more than cobalt acid battery of news file before. A manganese acid lithium ion battery uses manganese acid lithium for the proper pole of the battery. The efficiency of the charge of the usual lithium ion battery is good, and composition is easy, and uses cobalt acid lithium, which is easy to produce. One side where a material fee is cheap, the stability at the high temperature of manganese acid is low, and composition is difficult. Only NEC Moli Energy corporation who is the subsidiary company of NEC succeeds in the mass production. NEC Moli Energy corporation is extending market share by the price competition power. It seems to have the possibility that manganese acid becomes the main force with a battery by two by new entering of Sony Co., Ltd. of the lithium ion battery extreme big enterprises. (translated by NEDO)

  20. Technological development for super-high efficiency solar cells. Survey on the commercialization on analysis; Chokokoritsu taiyo denchi no gijutsu kaihatsu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on analysis of super-high efficiency solar cells for practical use in fiscal 1994. (1) On the survey on crystalline compound solar cells, it was pointed out that the present study target is III-V compound semiconductor solar cell, and efficiencies of 36-39% are theoretically expected by use of two-junction cells. (2) On structure of super-high efficiency solar cells of 40%, selection of upper and lower cell materials for multi-junction cells, high-efficiency tandem Si solar cells, and the merit and possibility of light collection operation were surveyed, and their issues were discussed. (3) On physical properties of mixed crystalline semiconductors and characteristic evaluation of solar cells, impurities, trap center, minority carrier life, and applicability of supper lattice structure to high-efficiency solar cells were surveyed. (4) On fabrication technology of compound semiconductor solar cells, various problems of and approaches to electrode formation and antireflection film technologies, the meaning and issues of thin film substrate technology and continuous process, trial calculation of costs, safety, and resource problem were surveyed.

  1. Indirect solar-pumped laser diode using a solar cell; Taiyo denchi wo mochiita taiyoko kansetsu reikigata handotai laser no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kanamori, Y.; Yugami, H.; Naito, H.; Arashi, H. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-10-27

    This paper describes the operating characteristics of a stabilizing circuit using commercial electricity, those of a stabilizing circuit using solar cells, relation between the quantity of solar radiation and the maximum output of a semiconductor laser diode (LD), and simulation results of annual LD output in Sendai City. The stabilizing circuit for the solar-cell driven LD was structured such that the output of the solar cell panels was guided to a DC/DC converter, that the voltage was set at a prescribed value and that the current was stabilized with the use of power MOSFET. The solar cells used in the experiment were monocrystal silicone solar cells with the maximum output of 53W each. In the experiment, the LD was protected by stabilizing the current at a set value when an excess current was supplied to the stabilizing circuit. As a result of the simulation of the annual LD output from the meteorological data of Sendai City, it was predicted that a solar cell of approximately 1kW was able to provide an annual output of 102MJ and that the efficiency was highest with four sheets of the solar cell. Consequently, consistency proved to be essential between the LD and the solar cell output. 3 refs., 7 figs.

  2. Control method for light deterioration of amorphous solar cell. Temperature effect method; Amorphous taiyo denchi no hikari rekka yokuseiho. Ondo kokaho

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H.; Yokoyama, S.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

    1996-10-27

    This paper describes a proposed method for suppressing light deterioration (temperature effect method), in which an annealing effect was always expected by laminating an NEM element and a heat insulation material on the back side of a-Si solar cell module and thereby raising the temperature in the back side of the module, and also describes an outdoor exposure test device completed for the method. The NEM element consisted of conductive potassium titanate and high molecular polymer and was a self temperature-controlling organic exothermic body that required no outside temperature control device. It was provided with a heat generating temperature of 45-75{degree}C as the exothermic property of the element and capable of generating heating temperature arbitrarily according to the purpose. The NEM element varied a resistance value against the ambient temperature and kept the element temperature constant. Measurement was commenced starting April 19, 1996, using the completed outdoor exposure test device and a measuring circuit. The deterioration phenomenon was and from then on continuously examined under the following conditions: (1) measurements were those of clear days only, and (2) measurements to be used were those between 10:00 and 14:00 with the quantity of solar radiation on a constant level. 4 refs., 4 figs., 1 tab.

  3. Development of measurement device for evaluation of solar cell module output. 2; Taiyo denchi module shutsuryoku hyokayo sokuteiki no kaihatsu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Minoda, M.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

    1996-10-27

    Enhancement in design efficiency may be attained as well as utilization in maintenance if on-the-spot data is made available, for the purpose of flexibly dealing with changes in design or matching with a house structure, in calculating the power generation output of a solar cell (PV) module. Under the circumstances, a small-sized compound measuring device was produced as a prototype which, using an I-V curve tracer, measured output and condition of a roof at the time of installation, compared with the optimum operation and predicted the power generation. The device was structured with the main body consisting of a computing part, measurement controller and power supply and with various sensor modules. The electron load control method was employed in order to measure I-V characteristics of the PV module, since it was desirable to use a variable load and to cover the range from the release voltage of a solar cell to the short-circuit state through the maximum output point. The reference module method was used for the system evaluation. The device was presumably applicable to a PV system design by incorporating a sensor module for measuring design environment data, which was essential at the time of a system design, in addition to those for measuring output. 9 refs., 4 figs., 3 tabs.

  4. Effect of PV module output power on module temperature; Taiyo denchi no shutsuryoku henka ga module hyomen ondo ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Hongo, T; Kitamura, A [Kansai Electric Power Co. Inc., Osaka (Japan); Igaki, K; Mizumoto, T [Kanden Kako Co. Inc., Osaka (Japan)

    1996-10-27

    Effect of the photovoltaic (PV) module output power variation on the module surface temperature has been investigated by field measurements. PV modules with capacity of 54 W were used for the temperature measurements. Three 2 kW-class PV systems were operated. T-type thermocouples were used for measuring temperatures. Measurement time intervals were 15 minutes, 30 minutes, 60 minutes, and 24 hours. Measurement period was between May 25, 1995 and June 25, 1996. The surface temperature increased during non-loaded PV output, and decreased during load-carrying PV output. Difference of the surface temperature between non-loaded PV output and load-carrying PV output was 3.5{degree}C at maximum through a year. The surface temperature was saturated within 30 minutes. When PV output was changed in 30 or 60 minutes interval, the variation of surface temperature was distinctly observed. When PV output was changed in 15 minutes interval, it was not observed distinctly. There was no difference of the surface temperatures during the time zones with less solar radiation, such as in the morning and evening, and at night. Except these time zones, difference of the surface temperatures was 3.5{degree}C at maximum. 4 figs.

  5. Study on property-gradient polymer electrolyte for rechargeable lithium batteries; Lithium niji denchi no tame no keisha tokusei kobunshi denkaishitsu no sosei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kokumi, Z; Kanemura, S; Inaba, M; Takehara, Z; Yao, K; Uchimoto, Y [Kyoto University, Kyoto (Japan)

    1997-02-01

    This paper describes the fundamental experiments for creating property-gradient polymer electrolyte for rechargeable lithium batteries. The rechargeable lithium battery is composed of an anodic composite agent section with high ion conductivity, a separator equivalent section with high mechanical strength (high bridging degree), and a section surpressing the precipitation of metal lithium by contacting with it. The continuous property-gradient polymer electrolyte was tried to be synthesized by means of the plasma polymerization method. As a result, plasma polymerization electrolyte with high ion conductivity could be prepared from the liquid phase by using a monomer with low vapor pressure. Porous material simulating the anodic composite agent was impregnated by the monomer, which was plasma-polymerized. As a result, it was found that the bridging degree decreased from the surface towards the inside of the plasma-polymerized porous material. In addition, polymer was prepared using fluorine-base monomer. Thus, LiF thin film could be prepared through the reaction between the polymer and metal lithium. 3 figs.

  6. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for development of extra-high efficiency solar cells (fundamental research on extra-high efficiency Si solar cells); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (chokokoritsu silicon taiyo denchi gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Sekikawa, T; Suzuki, E; Ishikawa, K; Takato, H; Yui, N; Shimokawa, R [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation for development of extra-high efficiency silicon solar cells. It is necessary for development of extra-high efficiency Si solar cells to extend as far as possible service life of minority carriers and to develop the evaluation techniques. Noting photoluminescence (PL) observable even with Si, the method of evaluating characteristics of minority carriers, which are not limited in samples, is developed to experimentally determine their service life from transitional response of the PL characteristics. Si has an extremely low quantum effect, because it is an indirect transitional semiconductor, and needs measurement of very high sensitivity. A rapid heat annealing apparatus and others to generate carriers in the infrared and ultraviolet regions are provided in consideration that these are possible means to increase efficiency. These possibilities will be pursued by developing the annealing techniques. 1 fig.

  7. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for thin substrate polycrystalline solar cells (compound semiconductors and their fabrication technologies); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Usumaku taiyo denchi jitsuyoka no tame no kaiseki hyoka (kagobutsu taiyo denchi zairyo oyobi seisaku gijutsu no kaiseki hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    Oyagi, H; Okada, Y; Yamaguchi, H; Shiota, T; Kuroda, S; Igarashi, O; Tanino, H; Makita, Y; Yamada, A; Kimura, S; Ohara, A; Niki, S; Shibata, H; Fons, P [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation for thin-film compound semiconductor solar cells. The study on epitaxial growth and optical properties of the thin films of CuInSe2 and CuGaSe2 evaluates the thin epitaxial films grown under various conditions, showing morphology of the defects at the interface of heteroepitaxial growth. These results are used to set the growth conditions under which a thin film of high luminescence by exciter recombination is produced. The study also gives information of luminescence transition in the vicinity of the band ends and of energy level between the bands. The study on structural analysis of the epitaxially grown thin films of CuInSe2 investigates dependence of lattice constants of the MBE-grown CIS layer on film thickness by the X-ray diffractometry based on the bond method. The study on epitaxial growth by the Se(CH3)2-halogen transfer method tests epitaxial growth of the single-crystalline Mo on a substrate of single-crystalline sapphire. 5 figs.

  8. Leveling of battery load and extension of battery life by serial connection of electric double layer capacitors with batteries for electric vehicles. Experimental results on the small model; Denki jidoshayo denchi to denki nijuso capacitor no chokuretsu setsuzoku ni yoru denchi futan no heijunka oyobi denchijumyo no enshinka. (kogata model ni yoru jikken seika). Kogata model ni yoru jikken seika

    Energy Technology Data Exchange (ETDEWEB)

    Takehara, J.; Okubo, N.; Miyaoka, K. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1996-10-25

    The load leveling method of batteries for electric vehicles was studied for extension of a battery life and mileage every charging. Under large load fluctuation conditions such as deceleration and acceleration, use of electric power sources other than battery for peek load at acceleration can improve a battery life, output power capacity and mileage every charging. Combination of effective recovery of regenerative power at deceleration with its discharge at acceleration is one of the effective methods. The electric double layer capacitors are serially connected with the batteries, regenerative power is charged only into the capacitors, and both voltages of the battery and capacitor are applied to a power circuit. Battery load is reduced by load on the capacitor. Until the capacitor is re-charged by regenerative power after full discharge, power is supplied only by battery through a diode. Capacitor power is used as effectively as possible until approaching considerably low voltage. As peak load of the battery is reduced by 30%, the mileage increases by 5.7%, and the battery cycle life becomes 1.5 times longer. 7 refs., 5 figs., 3 tabs.

  9. Fiscal 1994 achievement report. Development of photovoltaic power generation system practicalization technology - Development of ultrahigh-efficiency solar cell technology (Development of new photoelectric conversion material technology - Research on future feasibility of wet-type solar cells); Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Chokokoritsu taiyo denchi no gijutsu kaihatsu (shinkoden henkan zairyo no gijutsu kaihatsu (shisshiki taiyo denchi no shoraiteki kanosei no chosa))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    A survey is conducted of wet-type solar cells that may constitute an important field in solar chemistry. The wet type solar cell made known by Graetzel et al. in 1991 is a combination of ultrafine TiO{sub 2} grains and a sensitizing dye. The ultrafine grain surface structure enlarges the area of an electrode for the absorption of 46% of incident solar radiation of which 80% or more is converted into electric power. The fill factor at 520nm of a cell fabricated for an additional test turns out to be 40% against the 76% mentioned in technical literature, and the conversion efficiency 10%. The Titanyl sulfate is also tested because it is low in price as material for titanium oxide. Functional groups are experimentally introduced for the generation of bonds on the substrate to be effective in the injection of a sensitizing dye. A sensitizing dye with two carboxyl groups and two bipyridine rings as ligand is allowed to be supported by TiO{sub 2}. IR (infrared) spectrometry is performed, and then formation is found of ester-like bonds or chelate bonds due to the interaction of carboxyl groups and the substrate surface. This is enhanced by surface treatment. (NEDO)

  10. Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (CuInSe2 based PV cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (CuInSe2 taiyo denchi seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of CuInSe2 based PV cell in fiscal 1994. (1) On formation of high-quality CIGS thin films by bilayer method, Mo film was deposited on a glass substrate by sputtering, and CIGS film with different Ga/In ratios was next formed on the substrate by quaternary simultaneous deposition at different In and Ga deposition speeds. In addition, CdS film was deposited on the CIGS film, and ZnO and ITO films were finally deposited on it by sputtering to complete solar cell. This solar cell offered the maximum conversion efficiency among cells using CIGS film. (2) On formation of high-quality CIGS thin films by three-stage method, a certain correlation was found between substrate temperature and CIGS film composition by monitoring substrate temperature in film forming process. This phenomenon allowed rigorous control of CIS film compositions important for CIS thin film solar cells. (3) On low-cost process technology for thin film formation, Cu(In,Ga)S2 solid solution film was fabricated by expanded selenic process. 3 figs.

  11. Research on fabrication technology for thin film solar cells for practical use. Research on low-cost fabrication technology for large-area modules (production technology for amorphous silicon solar cell modules); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Daimenseki module no tei cost seizo gijutsu (amorphous taiyo denchi module seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of amorphous Si solar cell modules in fiscal 1994. (1) On process technology for prototype film substrate solar cells, an advanced preprocessing equipment for film substrates, stepping roll type film forming technology, and prototype submodules were studied. A conversion efficiency of 7.2% was achieved by use of the submodule formed in an effective region of 40 {times} 40cm{sup 2}. (2) On efficiency improvement technology for film substrate solar cells, p/i and n/i interfaces, forming condition for Ag film electrodes, film thickness of transparent electrode ITO, and optimum transmissivity were studied. (3) On technology for advanced solar cells, high-quality a-SiGe: H film, ion control in plasma CVD, and a-Si film formation by plasma CVD using SiH2Cl2 were studied as production technology of narrow gap materials. (4) On advanced two-layer tandem solar cells, the defect density in optical degradation of a-Si cells by reverse bias dark current was evaluated, and outdoor exposure data were analyzed. 4 figs., 1 tab.

  12. Research on fabrication technology for thin film solar cells for practical use. Research on low-cost fabrication technology for large-area modules (CdS/CdTe solar cell modules); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Daimenseki module no tei cost seizo gijutsu (CdTe taiyo denchi module seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of CdS/CdTe solar cell modules in fiscal 1994. (1) On the fabrication technology for high-efficiency large-area solar cells, high-quality CdTe active layer was studied. S content taken in the active layer at sintering of CdTe decreased with an increase in formed CdTe, resulting in improvement of Voc of cells. (2) On the window layer with wide band gap, the solar cell superior in collection efficiency and photoelectric characteristics could be obtained using the newly developed mixed crystal film of Cd(1-x)Zn(x)S. (3) On the forming technology of large-area coating/sintering films, improvement of CdS film quality was studied by pressurized processing of printed CdS films. As a result, improvement of film density and light transmissivity was confirmed. (4) On the leveling process technology of CdTe films, smooth surface films were obtained by experiment using an equipment simultaneously exciting samples in all directions as one of uniform coating methods of films. 7 figs.

  13. Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (research and development of composite materials on solar cells under microgravity environment); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (bisho juryoku kankyo wo riyoshita taiyo denchiyo zairyo kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on development of composite materials for solar cells under microgravity environment in fiscal 1994. (1) On a thin film capillary method, 26 experiments of GaSb thin film crystal growth were conducted using the especially prepared high-accuracy electric furnace under microgravity. The wettability of thin film crystals was improved by refining equipment. Rhombus crystal planes and large crystal grains were observed in GaSb thin film crystals prepared under microgravity. (2) On a liquid phase method, the effect of the gravity on crystal structure and grain morphology was studied for synthesis of CdS fine grains. (3) On technological development of composite materials, the solidification experiment of Cu-In-Se melt was conducted under short time microgravity of 10{sup -4}g for 10 sec. As a result, more uniform texture and more high crystallinity were obtained under microgravity, and In in melt was concentrated by surface tension effect. It was suggested that high-quality CIS thin films will be obtained by Se doping into Cu-In composite films under microgravity environment.

  14. Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (development of fabrication technology of thin film polycrystalline Si solar cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (usumaku takessho silicon kei taiyo denchi seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of thin film polycrystalline Si solar cells in fiscal 1994. (1) On the fabrication technology of high-quality Si thin films, the new equipment was studied which allows uniform stable melting recrystallization over a large area. The new equipment adopted a heating method based on RTP system, and is now under adjustment. (2) On the fabrication technology of light/carrier confinement structure, degradation of hydrogen-treated thin film Si solar cells by light irradiation was examined. As a result, since any characteristic degradation was not found even by long time light irradiation, the high quality of the cells was confirmed regardless of hydrogen-treatment. Fabrication of stable reproducible fine texture structure became possible by using fabrication technology of light confinement structure by texture treatment of cell surfaces. (3) On low-cost process technology, design by VEST process, estimation of cell characteristics by simulation, and characteristics of prototype cells were reported. 33 figs., 1 tab.

  15. Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (improvement of conversion efficiency of amorphous silicon solar cells after degradation); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (amorphous taiyo denchi no shoki rekkago koritsu kojo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development for qualitative improvement of a-Si solar cells after initial degradation in fiscal 1994. On the fabrication technology of light-stable a-Si films, the film formation method possible to control combined hydrogen by repetitive formation/treatment was developed. The obtained high-quality light-stable a-Si film was featured by low defect density in a wide optical band gap range, and defect density of nearly 3 {times} 10{sup 16}/cm{sup -3} after light irradiation. The light degradation rate of the cell where the a-Si film was applied to i layer was relatively stable by 10% or less. The a-Si/a-Si double-layer tandem cell fabricated by this technology produced a high conversion efficiency of 10.5%. By applying {mu}c-Si material to photoactive layer as narrow band gap material, the cell with optical sensitivity even in long wavelength ranges more than 1000nm was obtained. The a-Si/{mu}c-Si double-layer tandem cell produced an initial efficiency of 8.0% and an efficiency after degradation of 7.5%. 12 figs., 3 tabs.

  16. Technological development for super-high efficiency solar cells. Technological development of solar-high efficiency singlecrystalline silicon solar cells (high quality singlecrystalline silicon substrates); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (kohinshitsu tankessho silicon kiban no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development for high quality efficiency singlecrystalline silicon substrates in fiscal 1994. (1) On electromagnetic casting/once FZ bath method, a Si single crystal of 600mm long was successfully obtained by improvement of power source frequency and furnace parts. High carbon content resulted in no single crystal including solids. In undoped electromagnetic casting ingots, resistivities over 1500ohm-cm were obtained because of effective preventive measures from contaminants. (2) On electromagnetic melting CZ method, since vibration and temperature control of melt surface by magnetic shield was insufficient for stable pulling of single crystals, its practical use was hopeless. (3) On electron beam melting CZ method, a Si single crystal of 25mm in diameter was obtained by preventive measures from evaporation of Si and influence of deposits, and improved uniform deposition distribution in a furnace. The oscillation circuit constant of power source, and water-cooling copper crucible structure were also analyzed for the optimum design of electromagnetic melting furnaces. 3 figs., 1 tab.

  17. FY 1998 annual report on the fuel/storage working group. 19th R and D activity report; 1998 nendo nenryo chozo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    Summarized herein are the FY 1998 R and D activities by the fuel/storage working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, outlined the R and D activities for development of techniques for fuel cell power generation, development of decentralized cell power storage systems, demonstration of new load-leveling techniques, development of techniques for superlow-loss type power system components, development of techniques for ceramic gas turbines, pioneer R and D for MGC superhigh-efficiency turbine system techniques, demonstration tests for establishing centralized load controlling systems, development of techniques for network systems utilizing wide-area energy, development of techniques for application of superconductor-aided power systems, R and D for power storage aided by a high-temperature, superconducting flywheel, R and D for basic techniques for applying superconductors, and pioneer R and D for basic techniques for AC superconducting power equipment. The individual NEDO's researchers reported their results, which include outline of the fuel/storage technique development group, and current statuses of fuel cell technique development, new cell-aided power storage technique development, and superconductor technique development. (NEDO)

  18. Research on the general analytical method of fossil fuel cycle from a viewpoint of the global environment. 3; Chikyu kankyo kara mita sogoteki kaseki nenryo cycle bunseki hyoka shuho no chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The general analysis/assessment method of a fossil fuel cycle was studied. Seven kinds of power generation plants such as LNG cycle and coal cycle ones, and four kinds of transport and treatment systems of recovered CO2 such as ocean and underground systems were studied as case studies on life cycle analysis. As data necessary for life cycle analysis, the database was constructed which stores the facilities and operational energy required for a total energy system from mining of fossil fuel to treatment of recovered CO2, and the quantity of environmental waste such as CO2 emission. As a result, the decrease rate of energy balance defined as ratio of input energy to power plant output was estimated to be 14-43% and 20-60% in LNG cycle and coal cycle, respectively. Even if the recovery rate of CO2 in power plants reached 80-90%, reduction of total CO2 emission was limited to only 20-40% because of CO2 emission during mining, liquefaction and transport of fuel. 168 refs., 48 figs., 102 tabs.

  19. Dynamic programming for reduction of fuel consumption in a photovoltaic/wind/diesel generating system; Doteki keikakuho ni yoru taiyoko/furyoku/diesel hatsuden system no nenryo shohiryo no sakugen

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, K.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

    1997-11-25

    Dynamic programming is employed in the study of the operation of the diesel engine in a photovoltaic/wind-force/diesel-engine power generating system, which aims at reduction in the system fuel consumption and at determining an optimum system constitution. The parameters set in this system are the photovoltaic/wind-force supply rate, photovoltaic/wind-force power generation ratio, and battery capacity. An island in Ise Bay, with an annual load power of approximately 1.59-million kWh and mean daily load power of approximately 4336kWh is assumed as the location for the system. Observation data of Ommaezaki Weather Station are utilized for the calculation of the amount of photovoltaic/wind-force power generation. It is found as the result that the fuel consumption of the diesel engine in this system decreases to 82-84% when the natural energy supply rate is 20%. It is also found that the fuel consumption of the system records the minimum at a photovoltaic/wind-force ratio of 60/40, irrespective of the battery capacity or natural energy supply rate, and this ratio is the optimum ratio. 3 refs., 9 figs., 1 tab.

  20. Activation of charcoal made from japanese cypress as oxygen electrode in fuel cell by deposition of Pd-metal/Heteropolyacids of the micropores; Kinzokuparajiumu-heteroporisan no bunsan tanzi niyoru hinoki mokutan no nenryo denchisansokyoku to shiteno kinouka

    Energy Technology Data Exchange (ETDEWEB)

    Yumine, Takuya.; Kominami, Hiroshi.; Kera, Yoshiya. [Kinki University, osaka (Japan); Abe, Ikuo. [Osaka Municipal Technology Research Institute, Osaka (Japan)

    1998-12-31

    Pd- and Pt-metal were observed by TEM to be highly disperdsed on charcoal prepared from Japanese Cypress [Hinoki] at 900degreeC (Pd, Pt/H2). Nafion-sheet was hot-pressed with Pd/H2 and Pt/H2 disc-pellets placed in the other sides to make a fuel cell-electrode unit. The 1-V curve in the H{sub 2}-O{sub 2} fuel were measured : The voltage certainly grew with increase in the amount of Pd-metal (1{yields}13wt%) and with a mixing of [Nafion] powder (11wt%). The discharge character was greatly improved with the addition of heteropolyacid (H{sub 3}PMo{sub 11}VO{sub 42};PVMo{sub 11}). When a charcoal prepared from Hinoki at 2400degreeC (HG) was used, the inner resistivity was about 10-times lower than the case of H2 used, although the dispersed states of Pd-metal became considerably poor on HG rather than H2. The actuvuty also increased further with the addition of Nafion and PVMo{sub 11}. (author)

  1. Secretive production of long-chain fatty acids, triacylglycerols and n-alkane-2-ones by fermentation processes; Hakkoho ni yoru ekitai nenryo no seisan wa kanoka (shishitsu no bunpi seisan)

    Energy Technology Data Exchange (ETDEWEB)

    Fukui, S. [University of Fukuyama, Hiroshima (Japan). Faculty of Engineering

    1995-10-20

    Secretive production of lipids, which are useful source for engine-driving fuel, by microbial process using carbohydrate biomasses as substrate has been investigated in our laboratory. This review consists of four parts concerning breedings and selection of lipid-secretive microorganisms : (1) breedings of long-chain fatty acid-secretive strains from Candida lipolytica L-1 by a step-wise mutagenesis process, (2) selection of a triacylglycerol (TG)-secretive and accumulative yeast strain Trichosporon sp. SH45Y, (3) breedings of mutants, SH45Y-derivatieves, having potent ability to produce TG secretively from glucose, a typical biomass charbohydrate, and (4) selection of microorganisms which produce liquid-n-alkane in culture medium by utilizing long-chain fatty acids and TG; a strain of Penicillium decumbens can produce liquid alkalis with a yield of approximately 60 % in weight from palm kernel oil, a commercial TG. 10 refs., 7 figs., 7 tabs.

  2. Attempt of lean burn of a 4 cycle gasoline engine by the aid of low pressure air assisted in-cylinder injection; Tonai kuki nenryo funsha ni yoru lean burn no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Hatakeyama, S; Kondo, M; Sekiya, Y; Murayama, T [Hokkaido Automotive Engineering College, Hokkaido (Japan)

    1997-10-01

    Comparable performance and exhaust emission with conventional carburetor was obtained by a low Pressure air assisted in-cylinder injection system. And lean burn of idling and light load operation till A/F=70 was realized by installing a spark Plug and a reed type injection nozzle in a divided combustion chambaer of a 4 cycle gasoline engine. 2 refs., 10 figs.

  3. Numerical simulation of growth of flames formed in two-dimensional mixing layer. 2nd Report. Effect of dilution of fuel; Nijigen kongo sonai ni keiseisareta kaen no seicho ni kansuru suchi simulation. 2. Nenryo no kishaku ni yoru eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Noda, S [Toyohashi University of Technology, Aichi (Japan); Hashimoto, K [Sumitomo Metal Industries, Ltd., Osaka (Japan); Nakajima, T [Kobe University, Kobe (Japan). Faculty of Engineering

    1994-07-25

    The effect of fuel dilution on growth of flames formed in 2-D mixing layers was studied by numerical simulation. The methane mass fraction of fuel was adjusted to 1.0, 0.3 and 0.2 through dilution by nitrogen, while the oxygen mass fraction of an oxidizer was fixed at 0.27. Flame structure was complicated due to the flows separated by flame at the leading edge of flames, and three peaks of the second Damkohler number were observed. Fuel dilution by nitrogen caused blow-off of flames, and the mixing ratio of the fuel and oxidizer at the leading edge of flames was essential to blow-off of diffused flames. In the case where vortices were observed in a flow field, the first Damkohler number was important which was determined by the hydrodynamic characteristic time of coherent vortices and the chemical characteristic time of flame propagation based on the mixing ratio of the fuel and oxidizer at the leading edge of flames. The diffused flames were elongated by shearing force, and an exothermic reaction was suppressed and a flame stabilization decreased with a decrease in second Damkohler number. 10 refs., 9 figs., 1 tab.

  4. Stability of diffusion flame formed in a laminar flat plate boundary layer. Effect of fuel dilution; Soryu heiban kyokai sonai ni keiseisareru kakusan kaen no anteisei. Nenryo kishaku no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, M [National Institute for Resources and Environment, Tsukuba (Japan); Ueda, T; Mizumoto, M [Keio University, Tokyo (Japan). Faculty of Science and Technology; Amari, T [Keio University, Tokyo (Japan)

    1998-10-25

    A stability limit of the diffusion flame with fuel injection from a porous wall in a laminar flat plate boundary layer is measured as functions of fuel (CH4) concentration of CH4/N2 injectant mixture ({chi}) and its injection velocity (v). The free stream velocity (U{infinity}) is set as 0.6 m/s. The thermal condition at the wall is controlled by setting temperature at the upstream end of the porous wall as a reference temperature. When v >20 mm/s, the flame becomes unstable with the separation of leading flame edge with decreasing {chi}. The value of {chi} at the stability limit is constant without regard to v as long as the wall temperature is kept constant. As the wall temperature is decreased the value of {chi} increases. The separation is supposed to take place as a result of the limit of the reaction rate. When v <20 mm/s, the flame becomes unstable with the oscillation. The value of {chi} at the stability limit increases drastically with decreasing v. The oscillation takes place mainly due to the repeat of the extinction due to heat loss to the wall and the flame propagation in the combustible layer. 10 refs., 8 figs., 1 tab.

  5. Proceedings of the Joint Meeting of The Fuel Society of Japan (1991). 28th Coal Science Conference/91st Coke Meeting; (Sha) nenryo kyokai godo taikai happyo ronbunshu (1991). Dai 28 kai sekitan kagaku kaigi dai 91 kai cokes tokubetsukai

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-07

    Relating to coke, studies are made on the rapid coke production method, oven investigation during carbonization, and operational management/control. As to coal science, studies are mainly on the brown coal two-stage liquefaction (BCL) method, and data on the pilot plant and PSU are reported. Concerning bituminous coal liquefaction, PSU data mostly including the NEDOL process, and characteristics of liquefaction residue and its effective utilization by thermal decomposition are reported. Regarding the liquefaction mechanism, an experimentally extensive study on catalyst, solvent and reaction conditions is made using model materials and coal itself on the bench scale and also in the pilot plant. Engineering subjects on residue, solvent deashing, scale attachment and coprocessing are also reported. Relations of decomposition process to coal chemical structure changes and reaction conditions are investigated. As to coal gasification, studies, which are not many, are conducted on material balance, heat balance, and image characteristics of char for gasification and factors controlling reactivity.

  6. Study of a fuel injection quantity sensor in diesel engine. Part 3. Experimental evaluation of the improved type micro turbine sensor; Diesel kikan ni okeru nenryo funsharyo sensor no kenkyu. 3. Funsharyo keisoku no seido kojo ni kansuru jikken hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Maehara, H; Iwasaki, T; Kobayashi, T [Zexel Corp., Tokyo (Japan)

    1997-10-01

    A Micro Turbine Sensor has been developed to measure fuel injection quantity and injection rate. Previous reports described results of experiments on the MTS which were carried out under steady and unsteady flow conditions. The MTS has been improved in shape of a holder tip and a detecting procedure for rotating speed of a turbine. As a result revolution speed of the turbine increased 18% over the conventional type holder under steady flow condition. Furthermore the measurement resolution of the MTS came up to about 2(mm{sup 3}/pulse) at 20(mm{sup 3}/stroke) under intermittent spray conditions using fuel injection pump. 11 refs., 11 figs., 1 tab.

  7. Three-dimensional analysis of internal flow characteristics in the injection nozzle tip of direct-injection diesel engines; Sanjigen suchi kaiseki ni yoru DI diesel kikan no nenryo funsha nozzle nai ryudo tokusei no kaimei

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, H; Matsui, Y; Kimura, S [Nissan Motor Co. Ltd. Tokyo (Japan)

    1997-10-01

    To reduce the exhaust emissions and fuel consumption of direct-injection diesel engines, it is essential to optimize the fuel injection equipment closely related to combustion and emission characteristics. In this study, three-dimensional computation has been applied to investigate the effects of the injection nozzle specifications (e.g., sac volume, round shape at the inlet of the nozzle hole) and needle tip deviation on internal flow characteristics. The computational results revealed that the effects of the nozzle specifications and needle tip deviation with a smaller needle lift on internal flow characteristics and a general approach to optimize the injection nozzle specifications were obtained. 3 refs., 10 figs., 1 tab.

  8. Spray characteristics of dimethyl ether (D.M.E.) as on alternative fuel for diesel engine; Daitai diesel nenryo to shite no dimethyl ether (D.M.E.) no funmu tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Wakai, K; Nishida, K; Yoshizaki, T; Hiroyasu, H [Hiroshima University, Hiroshima (Japan)

    1997-10-01

    D.M.E. which was paid attention to as on alternative fuel for a diesel engine, was injected by using Bosch type injection pump and a hole nozzle into a high pressure and high temperature vessel. The spray was observed by using schlieren photography. Spray characteristics, such as, the tip penetration, the cone angle and the volume of the spray were and were compared with a diesel fuel spray. The following thing, and so on were found out as a results. The spray angle of the DME spray of atmosphere pressure Pa=0.1Mpa spreads out large in comparison with the diesel fuel spray, and the way of the change by the pressure is contrary to the case of the diesel fuel spray. 3 refs., 6 figs., 1 tab.

  9. Injection and spray characteristics of a variable orifice nozzle applied the jerk type fuel injection pump for DI diesel engine; Jerk shiki nenryo funsha pump wo mochiita kahen funko nozzle no funsha funmu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, T; Matsui, K; Iwasaki, T; Kobayashi, T [Zexel Corp., Tokyo (Japan); Matsumoto, Y [The University of Tokyo, Tokyo (Japan)

    1997-10-01

    A Variable Orifice Nozzle (VON) by changing a cross-sectional area of the nozzle injection hole, for improving a rate of injection and injection duration, has been developed to study its injection and spray characteristics. The nozzle geometry was optimized to analyze a nozzle internal flow by computational method. Results show that, injection and spray pattern responded to the nozzle orifice cross-sectional area which is changing larger to smaller in the part load range. This results suggest to contribute a combustion improvement which decreasing NOx and soot. 14 refs., 10 figs.

  10. Life cycle assessment for next generating vehicles. Feasibility study of alternative fuel vehicles and electric vehicles; Jisedai jidosha no life cycle assessment. Daitai nenryo jidosha oyobi denki jidosha no feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Hanyu, T; Iida, N [Keio University, Tokyo (Japan)

    1997-10-01

    To show environmental assessment of introduction of substitute fuel vehicles is important information to formulate the future vehicles policy. Life cycle assessment (LCA) is put forward to simulate such potential, allows us to state the reduction environmental impacts of substitute vehicles on their total life cycle. The purpose of this study is assessment and analysis of the life cycle CO2 emission for substitute fuel vehicles, such as, alternative fuel vehicles, electric vehicles, and hybrid electric vehicles. 8 refs., 9 figs., 3 tabs.

  11. Assessment of effects of maturity of Japan`s economy and society and improvement in automotive fuel consumption on demand for automotive fuels; Nippon keizai shakai no seijukuka to nenpi kaizen ga jidoshayo nenryo juyo ni ataeru eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Shimomura, S. [The Institute of Energy Economics, Tokyo (Japan)

    1998-04-01

    This paper evaluates impacts of the maturity of Japan`s economy and society and the improvement in automotive fuel efficiency on the demand for automotive fuels by FY 2010. Standard case and lower order case were examined. When the traffic volume of passenger cars in FY 1995 is assumed to be 100, it become 121 and 119 in standard and lower order cases, respectively. The traffic volume of lorries become 106 and 102 in standard and lower order cases, respectively, which showed a rather small growth. Deterioration rate of the fuel consumption was estimated by considering the difference in fuel consumption of new cars and existing cars. Although the fuel consumption will be lowered by FY 2000 when the cassation rate of ordinary passenger cars will rapidly increase, the impact will be lowered after that. For lorries for commercial use, the running fuel consumption will be gradually lowered due to the increased carrying capacity and vehicle weight a lorry with improving the transportation efficiency. Decreased running speed by traffic jam is also a cause of the deterioration of fuel consumption. When a policy of improvement in the fuel consumption is promoted in a background of CO2 issues, the fuel consumption of each vehicle will be gradually improved. The peak of fuel demand will be in FY 2005 by considering the changes in economical and social structures and the improvement in fuel consumption for the environmental protection. 5 figs., 3 tabs.

  12. Technologies for simulation improvement of NOx and PM emissions and fuel consumption of future diesel engines for heavy-duty trucks; Shorai no ogatasha diesel engine ni okeru NOx, PM, nenryo shohi no kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Shimoda, M.; Shimokawa, K.; Uchida, N.; Tsuji, Y.; Yokotaa, H.; Hosoya, M. [Hino Motors, Ltd., Tokyo (Japan)

    1999-01-01

    Future diesel engines for heavy-duty trucks are required to have significantly low NO{sub x} and PM emissions and fuel consumption characteristics. In order to improve these characteristics, various technologies including high pressure fuel injection systems, combustion optimization. high boost pressure turbocharging, EGR homogeneous charge compression ignition combined with multiple injections, and aftertreatment are discussed. As each technology has a number of challenges to overcome, it will take long before engines with these technologies are commercially available. In this paper, the research activities accomplished to date are reported. (author)

  13. New concept for low emission diesel combustion. 2nd Report. Combustion improvement by applying EGR and oxygenated fuel; Teikogai diesel engine no nensho concept. EGR, gansanso nenryo ni yoru nensho kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Yokota, H.; Nakajima, H.; Kakegawa, T. [Hino Motors, Ltd., Tokyo (Japan)

    1998-05-01

    Described herein are performance of a new concept of premixed, multiple injection combustion, in which part of the fuel is injected into the combustion chamber at the early stage and the remainder is injected in the ordinary manner, and characteristics of the exhaust gases. Also described are the effects of EGR and oxygenated fuel on reduced HC emissions and fuel consumption. The ordinary premixed, multiple injection combustion system has problems related to fuel efficiency, and HC and particulate missions. When combined with an EGR system, this system reduces HC emissions to one-third. MTBE shows an effect of improving fuel efficiency, when mixed with diesel fuel. No particulate matter is exhausted and fuel efficiency is improved by 6%, when MTBE is present in the fuel at 30% by weight. The pre-mixture is less homogeneous in the absence of EGR and oxygenated fuel, producing a luminous flame observed in the fuel-rich region. No such a flame is observed, when MTBE is added to the fuel and suction air temperature is increased to the level corresponding to that associated with EGR, conceivably resulting from increased suction air temperature and lower boiling point of MTBE, which together make the pre-mixture leaner and more homogeneous. 7 refs., 9 figs., 2 tabs.

  14. Study on initial stage of diesel spray formation. Effects of the condition inside the nozzle sac; Diesel funmu no shoki keisei katei ni kansuru kenkyu. Sac nai nenryo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, N.; Tsujimura, K. [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Komori, M.

    1996-06-25

    To realize clean diesel exhaust, it is very important to clarify the atomization phenomena of the fuel spray. In this study, the initial stage of the atomization process of a diesel injection fuel spray was analyzed with a high-speed image converter camera under the conditions of atmospheric gas pressure and room temperature. As a result, it was found that the initial spray formation was greatly affected lay the condition inside the nozzle sac. In the case in which fuel existed in the sac, pin-like structure spray formation was observed at the initial injection stage. This phenomenon was not observed in the case in which no fuel was present in the sac, and a widely spread fuel spray formation was observed at the initial injection stage. The relatively low-speed fuel spray injected in the initial low-sac-pressure condition was pushed away by the subsequent fuel spray injected in the high-sac-pressure condition. 7 refs., 12 figs., 1 tab.

  15. Report of commission for investigating MHD on a visit to U.S. Part 2. Report on each place of visit; Hobei MHD chosadan hokokusho. 2. Homonsakibetsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-01-01

    The members of MHD project examination subcommittee made an investigative tour of the U.S. on the state of development of MHD generation. This report of the 2nd part explains opinions and the present status of the R and D on MHD generation by each of the 19 institutions visited. The U.S. research on MHD generation is under the leadership of DOE, whereby the budget for the development is so large as nearly one hundred million dollars have been provided for several years. The purpose is the effective use of domestic coal. General Electric is of the opinion that a combined gas turbine system will be put to practical use earlier because MHD takes time for practicability despite its highest efficiency in coal-utilized power generation. Yet, GE thinks MHD will be more attractive in the future. Reynolds Metal is considering application of MHD generation to the electro-chemical industry at present. According to Reynolds, combined supply of electric output and heat of MHD can reduce the use of calorie per ton of aluminum from 240 MBTU to 100. Montana Power is promoting practicability through a combined plan with DOE-built MHD generation. (NEDO)

  16. Fiscal 1997 report on a feasibility study of international joint researches in the Asian region; 1997 nendo chosa hokokusho (Asia chiiki kokusai kyodo kenkyu kanosei chosa (4)hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is thought that the energy consumption in Asian countries with ASEAN and China as center will a marked growth also in future together with a rapid economic growth, but harmony with environmental problems and economic growth is being taken as a serious problem. This is an important issue also to Japan from viewpoints of secure energy supply and regional response to the environmental issue. Accordingly, strongly desired is positive response to global environmental issues and promotion in development/spread of new energy/energy conservation in these countries. For the spread of the technologies, actual construction/operation of plants by joint researches with Japan are effective from aspects of personnel raising, technical improvement, PR effects, etc. This is also helpful for Japan in terms of technological development because Japan can also get the unobtainable data from the operation under appropriate conditions. This is a report on the studies of the trends of global environmental problems in Thailand, Indonesia, Malaysia, the Philippines, India and China. 3 figs., 72 tabs.

  17. Fiscal 1997 report on the investigational research on intelligent social infrastructure technology; 1997 nendo chosa hokokusho (chiteki shakai kiban kogaku gijutsu no chosa kenkyu hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper first described an aim and outline of intelligent social infrastructure technology, summed up the system of social infrastructure and the situation in Japan in terms of the structure, lifeline, moving bodies such as railroad and automobiles, communication, security, and maintenance. Considering this present situation, the paper next described a concept of the intelligent social infrastructure technology to be newly constructed and a course of the development. Besides, as subjects required to study for the development of intelligent social infrastructure technology, it reported on risk management, methods of definition/collection/transfer/supply of information, infrastructure applicable at emergency, normal/emergency dual course system, privacy, robustness, and additionally the problems to be caused pertaining to architecture/civil engineering, traffic, security, communication, etc. when the infrastructure develops as a social system. Moreover, as element technology, the intelligent system related technology and data communication technology were described in detail. Examples of the research project were also reported. 101 refs., 70 figs., 42 tabs.

  18. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells/development of technology to manufacture low-cost large-area modules/development of technology to manufacture next generation thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction); 1997 nendo tiayoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module esizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A thin film single crystal silicon solar cell module is developed, in which a porous silicon layer is formed on the surface of a long-sized single crystal silicon substrate, a single crystal silicon film is integrated on the layer by epitaxially growing the film thereon to form a solar cell, and the solar cell is peeled off from the silicon substrate and transferred to a plastic film substrate. The achievements during this fiscal year may be summarized as follows: simultaneous formation of a porous silicon layer on a silicon substrate, reduction of anode formation current density from 200 mA/cm{sup 2} to 10 mA/cm{sup 2}, development of a silicon epitaxial device using a carbon heater, and attainment of aperture conversion efficiency of 11.8% in a thin film single crystal silicon solar cell. Three kinds of methods were developed to peel off the solar cell. A method was developed to grind silicon substrate surface from which the solar cell has been peeled off. A technology was developed to obtain a long-sized silicon substrate of about 30 cm times 10 cm times 0.1 cm from a 4-inch silicon ingot by using a wire saw. (NEDO)

  19. Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture application type thin film solar cells with new structure (development of technologies to manufacture amorphous silicon and thin film poly-crystal silicon hybrid thin film solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon/usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development was performed with an objective to manufacture amorphous silicon and thin film poly-crystal silicon hybrid solar cells with large area and at low cost, being a high-efficiency next generation solar cell. The research was performed based on a principle that low-cost substrates shall be used, that a manufacturing process capable of forming amorphous silicon films with large area shall be based on, and that silicon film with as thin as possible thickness shall be used. Fiscal 1997 has started research and development on making the cells hybrid with amorphous silicon cells. As a result of the research and development, such achievements have been attained as using texture structure on the rear layer in thin poly-crystal silicon film solar cells with a thickness of two microns, and having achieved conversion efficiency of 10.1% by optimizing the junction interface forming conditions. A photo-deterioration test was carried out on hybrid cells which combine the thin poly-crystal silicon film cells having STAR structure with the amorphous silicon cells. Stabilization efficiency of 11.5% was attained after light has been irradiated for 500 hours or longer. (NEDO)

  20. Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, development of technologies to manufacture next-generation thin film solar cells (development of technologies to manufacture CIS solar cell modules); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (CIS taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development was made with an objective to achieve conversion efficiency of 13% in a 30 cm times 30 cm size submodule of a CIS-based thin film solar cell, and to develop a manufacturing technology that can achieve 140 yen/Wp. This paper describes the achievements attained during fiscal 1997. In fiscal 1997, based on the achievements reached during the previous year, a submodule with a size of 10 cm times 30 cm was fabricated for an attempt of improving the open voltage and short circuit current density. Simultaneously, the applicability thereof to a module with an area as large as 30 cm times 30 cm was evaluated. As a result of experimental discussions, enhancement in the open voltage was verified by increasing amount of Ga or sulfur, but it was not possible to achieve 600 mV or higher. In the research of component technologies to establish a mass production process, research and development was made on a high-resistance buffer layer film forming technology, a high-quality window layer film forming technology, a high-quality metallic rear electrode film forming technology, and patterning technologies. The outdoor exposure test was continued on laminated mini-modules with a size of 10 cm times 10 cm. (NEDO)

  1. 31st Solar Energy Promotion Committee Meeting - 6th Solar Cell Liaison Meeting. Report for fiscal 1993; Dai 31 kai taiyo energy suishin iinkai dai 6 kai taiyo denchi renrakukai (1993 nendo hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-04-25

    The above-named events were convened in the period of April 25-28, 1994, when a total of 71 presentations were given on research achievements. Presented in the session on thin film systems were 21 essays concerning the low cost manufacturing technology of low-area modules, development of film substrate a-Si solar cells, etc. Discussed at the symposium were the 'Autonomous development of photovoltaic power generation' and 'Practical application and research and development.' Presented in the session on crystalline Si systems were 17 essays concerning real-time observation of epitaxial growth using STM (scanning tunneling microscope), research on single crystal silicon manufacturing technology, etc. Discussed in the session on international cooperation was 'How international joint research should be.' Presented in the session on systems were 11 essays including the research and development of photovoltaic modules integrated with construction materials. Presented in the session on III-V group systems were 7 essays including the development of crystallized compound solar cell technology. Presented in the session on chalcopyrite II-VI group systems were 9 essays including the development of large area CdS/CdTe solar cell. (NEDO)

  2. Output characteristic of photovoltaic module on different installing conditions. Comparison with calculated value and measured value; Secchi joken no kotonaru taiyo denchi module no shutsuryoku tokusei. Suchi kaiseki to jissokuchi tono hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, T.; Morita, Y.; Iwawaki, H.; Fujisawa, T.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    The paper studied output characteristics of photovoltaic modules different in installation conditions on the basis of the energy balance state. In the study, an energy balance equation was constructed for insolation intensity, heat losses from PV surface/back, and output, in order to calculate cell temperatures in each installation condition. A comparative study was made between calculated results and measured data obtained on the top of the school building. The results indicated the following: The thickness of thermal boundary layer became approximately 27mm at insolation intensity of 800 W/m{sup 2}, ambient air temperature of 25degC, and wind velocity of 0.5m/s. When widening air gap from 20mm to 40mm, the cell temperature decreased 4degC, and the output increased 1.6%. In the case of installing photovoltaic modules on the roof considering the relation between the air gap in the heat balance state and the thickness of thermal boundary layer, heat from PV back was released outside the air gap if widening the air gap to more than 30-40mm. The type with a heat insulating material on the panel back decreased in output from other types. 5 refs., 7 figs., 4 tabs.

  3. Surface treatment method for hydrogen adsorbing alloy powder and alkali secondary battery fabricated by applying the method; Suiso kyuzo gokin funmatsu no hyomen shori hoho to sorewo tekiyoshite eraeta arukari niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, K. [Furukawa Electric Co. Ltd., Tokyo (Japan); Sawa, H. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1997-03-07

    Corrosion of alloy proceeds in the conventional hydrogen absorbing alloy because the composing hydrogen absorbing alloy powder contacts with high concentration alkali electrolyte in the battery. Immersion into alkali aqueous solution and pulverization by metal fluoride compound of the electrode have been practiced to solve the problem, but internal resistance of the battery increases and the charge and discharge properties of the battery are deteriorated. This invention relates to a method in which hydrogen absorbing alloy electrode powder or the hydrogen alloy electrode whose main content is the said powder is contacted with alkali aqueous solution to increase the specific surface area of the hydrogen absorbing alloy powder, followed by its contact with pH3-6 acidic aqueous solution containing fluorine ions. As a result, corrosion resistance of the surface of hydrogen absorbing alloy powder after the treatment against high concentration alkali electrolyte is improved to elongate the cycle life. Salts of LiF, NaF, KF, RbF, and CsF or their hydrogen salts can be used as the supply source of fluorine ions. 3 tabs.

  4. 28th Solar Energy Promotion Committee Meeting - 3rd Solar Cell Liaison Meeting. Report for fiscal 1990; Dai 28 kai taiyo energy suishin iinkai dai 3 kai taiyo denchi renrakukai. 1980 nendo hokoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-14

    The above events took place in Tokyo in the period May 14-17, 1991, when a total of 89 essays were presented. In relation with the thin film/a-Si systems, 55 presentations were given, which were 'Novel preparation technique termed Chemical Annealing for making a-Si:H with a rigid and stable Si-network,' 'Interface characteristics of a-Si:H films prepared by VHF (very high frequency) plasma CVD (chemical vapor deposition),' 'Preparation of amorphous superlattices by continuous method and characterization of the interface,' etc. In relation with the thin film/compound systems, 8 presentations were given, which were 'Preparation of CuInSe{sub 2} solar cells by selenization method,' 'Deposition of CuInSe{sub 2} films by ICB (ionized cluster beam) technique and their optical characterization,' 'Large-area CdS/CdTe solar cells,' etc. In relation with the crystal/compound systems, 8 presentations were given, which were 'Lattice strain relaxation processes in GaAs grown on Si,' 'Optical transmission studies of tandem solar cells,' etc. In relation with the crystal/Si systems, 18 presentations were given, which were 'Effect of electric field on effective minority carrier lifetime,' 'Computer analysis of surface recombination velocity for high efficiency crystalline silicon solar cells,' etc. (NEDO)

  5. Accomplishments hitherto achieved regarding the development of solar cell manufacturing technologies and the future course. Annex; Taiyo denchi seizo gijutsu kaihatsu no koremade no seika to kongo no hoko. Fuzoku shiryo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-07-01

    Collected in this paper are the results of evaluation and studies which were conducted, regarding the development of solar cell manufacturing technologies, by the Solar Cell Manufacture Evaluation Sub-Committee at its 4 meetings held in the period from May to August, 1985. For the development of technologies of manufacturing solar cells under the Sunshine Program, the development of technologies for manufacturing crystalline solar cells and amorphous solar cells is required. The Industrial Technology Council, Ministry of International Trade and Industry, in August, 1982, set intermediate goals to be achieved by fiscal 1985. To be developed for the practical application of crystalline silicon solar cells are a low cost experimental silicon refining system and an experimental solar panel manufacturing system. To be carried out for amorphous solar cells are basic studies including a study of physical properties, the development of a large-area high-efficiency solar cell manufacturing technology, and the development of a low cost monosilane manufacturing technology making use of molten salt electrolysis in a closed cycle. In fiscal 1984, 90% of the goals were attained, and now it is expected that almost all will be complete within fiscal 1985. (NEDO)

  6. Development of a new electric battery electric power storage system. Results of the 12-year R and D; Shingata denchi denryoku chozo system kaihatsu. 12 nenkan no kenkyu kaihatsu no seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    The paper described the results of the R and D which have been continued for 12 years on a new electric battery electric power storage system (load leveling function). The electric batteries for study were Na-S, Zn-Cl, Zn-Br, and redox type. Charge/discharge operation of 211 times was conducted of a pilot plant with a Na-S battery 1,000kW and 8-hour capacity. The overall efficiency of system was 71.5-76.0%, and the energy efficiency of battery was 86%. As a whole, the performance was able to be confirmed which can fulfil a developmental target. The system overall efficiency of 65.9% and battery efficiency of 76.1% were obtained. The experiment on battery life was carried out at plant together with the pilot operation. The mean life of Na-S battery was estimated at 800 cycles, and that of Zn-Br battery at 500-800 cycles. The effectiveness of the new electric battery electric power storage system was technically verified. For the future commercialization, studies on the following are needed: enhancement of reliability, easiness in maintenance/inspection, size reduction, cost reduction, etc. (NEDO)

  7. Design and construction of radiant panel for cooling and heating with photovoltaic and thermoelectric element modules; Taiyo denchi to netsuden soshi module wo mochiita fukusha reidanbo panel no sekkei oyobi shisaku

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M; Tani, T [Science University of Tokyo, Tokyo (Japan); Kadotani, K; Imaizumi, H [Komatsu Ltd., Tokyo (Japan)

    1997-11-25

    Utilizing cooling properties and current voltage characteristics of a small cooling panel using thermoelectric elements which had been fabricated previously on a trial basis, design and prototype production were executed on a large radiant cooling and heating panel driven by photovoltaic cell modules. The panel design set the cooling area to about 0.5 m {sup 2} and the number of elements to 70 pieces, and optimum number of elements in series and parallel connection was derived. As a result of the analysis, it was made clear that the optimum number of thermoelectric module arrays in series and parallel connection varies depending on insolation intensity. It was found preferable that the number of parallel connection array be set to one to two in a region or time period in which low insolation intensity is distributed in greater amount. In the case where high insolation intensity is distributed in a greater amount, setting it to two to three is preferable. By using the structured design method and the HASP Tokyo data, thermoelectric element modules were interconnected with 35 modules in series and two in parallel on a cooling panel installed on the roof of the Science University of Tokyo. A simulation result revealed that the average temperature difference on the cooled surface in summer is 4.37 degC, and the solar cell utilization rate is 0.67. It is necessary in the future to improve heat dissipation efficiency and area ratio. 1 ref., 12 figs., 5 tabs.

  8. Dependence of open-circuit voltage of SnO2-nSi solar cells; SnO2-nSi taiyo denchi no sanka ondo menhoi izonsei

    Energy Technology Data Exchange (ETDEWEB)

    Shinoda, S; Shimizu, A; Yano, K; Kasuga, M [Yamanashi University, Yamanashi (Japan). Faculty of Engineering

    1997-11-25

    Although metal(or semiconductor)-semiconductor solar cells, SnO2-nSi solar cell for example, are superior in cost and efficiency, its barrier height and open-circuit voltage V(oc) are lower than those of p-n junctions. To improve these defects, study was made on the dependence of V(oc) on oxidation temperature and surface orientation using various solar cells prepared from (100)Si and (111)Si under various oxidation conditions. As a result, the density of surface states increases with a decrease in oxidation temperature of Si substrates, resulting in an increase in diode factor and V(oc). In this case, since oxide films are extremely thin and contribution of non-terminated bonds is large in the initial oxidation stage, the quantity of dangling bonds is larger in (100) plane than (111) plane, resulting in an increase in diode factor and V(oc). Since the surface energy level (the degree of electrons dominated by acceptor-like surface state from this level to the top of a valence band) of (100) Si is lower than that of (111) Si, the effective barrier height and V(oc) increase. 28 refs., 6 figs., 2 tabs.

  9. Change of the equivalent circuit constants accompanied by the degradation and recovery of efficiency on a-Si solar cells; A-Si taiyo denchi no koritsu no rekka to kaifuku ni tomonau toka kairo teisu no henka

    Energy Technology Data Exchange (ETDEWEB)

    Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    Investigations were given on how the equivalent circuit constants change when efficiency of amorphous silicon solar cells changes with time in light degradation and temperature recovery. In the experiment, light irradiation tests under a constant temperature and light intensity condition, followed by recovery tests under a constant temperature and constant weak light intensity or constant temperature condition were repeated continuously. According to the result of an experiment on single layer type cells, the change in each equivalent circuit constant in association with degradation in efficiency and file factor and variation in recovery is reversible mostly. However, a slightly irreversible component was recognized only in the initial degradation process in series resistance and diode factor values. With regard to stacked cells, it was suggested that the main players to determine cell characteristics during the processes of deterioration and recovery take turns among the three layers as follows: the shape of the time-based change in the efficiency comes different and is not saturating; as the efficiency decreases, the extent of the change increases in the diode factor and series resistance; and the path the deterioration takes differs from that the recovery takes. 2 refs., 12 figs.

  10. Study on the best utilization of solar energy. Experimental study of hydrogen generation by water electrolysis using solar battery; Taiyo energy no yuko riyo ni kansuru kenkyu. Taiyo denchi riyosui denki bunkai suiso hassei field test

    Energy Technology Data Exchange (ETDEWEB)

    Kawashima, Y; Murai, K; Nakai, T [Himeji Institute of Technology, Hyogo (Japan)

    1997-11-25

    Shortcomings of solar energy are that it is subject to weather and is not available in the nighttime. The weak points may be effectively made up for when solar energy collected on a fine day is stored in the form of hydrogen energy for recovery as required. In this report, power generated by solar cells is used for the electrolysis of water for the generation of hydrogen. The amounts of the thus-generated hydrogen and hydrogen energy are determined and, on the basis of the measured amount of insolation, the solar energy availability rate (hydrogen conversion performance) is calculated. The amount of hydrogen generated in fiscal 1996 is also calculated for every month. The hydrogen generation level is quite low in the TiO2 wet type solar cell, approximately 0.2% at most. The current efficiency is fairly high in hydrogen generation using electrolysis, which is approximately 96-97%. The efficiency is higher when several units of electrolyte are connected in series until the solar cell optimum voltage is attained. A linear relationship is found between the daily summation of insolation and the amount of hydrogen generated. 1 ref., 7 figs., 2 tabs.

  11. 30th Solar Energy Promotion Committee Meeting - 5th Solar Cell Liaison Meeting. Combined report for fiscal 1989-1992; Dai 30 kai taiyo energy suishin iinkai dai 5 kai taiyo denchi renrakukai (1989-1992 nendo hokoku no matome)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-04-20

    The above-named events were convened in Tokyo in the period of April 20-23, 1993, where a total of 51 presentations were given on research achievements. Presented in the session on a-Si systems were 22 essays concerning high quality manufacturing technology - high integration technology, large area manufacturing technology - large area a-Si tandem solar cell, highly reliable manufacturing technology - bilayer device, composite transparent conductive film - transparent conductive film with performance enhanced by compositing, etc. Presented in the session on chalcopyrite and II-VI group systems were 8 essays concerning amorphous/compound tandem cell manufacturing technology, research on compound semiconductor solar cell, etc. Presented in the session of III-V group systems were 6 essays concerning research on compound semiconductor solar cell - superlattice structure tandem cell, development of InGaP/Si tandem solar cell, etc. In the session of crystalline Si systems, 15 essays were presented concerning highly pure silicon manufacturing technology, highly pure substrate manufacturing technology, etc. (NEDO)

  12. 29th Solar Energy Promotion Committee Meeting - 4th Solar Cell Liaison Meeting. (Report for fiscal 1991); Dai 29 kai taiyo energy suisuin iinkai dai 4 kai taiyo denchi renrakukai. 1991 nendo hokoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-04-21

    The above-named events took place in Tokyo in the period of April 21-24, 1992, and a total of 55 essays were presented. Presented in the session of the thin-film/a-Si systems were 27 essays, which were 'Light-induced degradation and its mechanism in a-Si:H and its multilayers,' 'Light-induced ESR (electron spin resonance) in a-Si{sub 1-x}N{sub x}:H,' 'Distribution of hydrogen surrounding light-induced defects,' 'Equilibration temperature and hydrogen diffusion in a-Si:H,' etc. Presented in the session of the thin-film compound systems were 6 essays, which were 'Local structure studies of CuInSe{sub 2} thin films,' 'Characterization of CuInSe{sub 2} bilayer films fabricated by ICB (ionized cluster beam) techniques,' etc. Presented in the session of the crystal compound systems were 7 essays, which were 'heteroepitaxy of In{sub x}Ga{sub 1-x}As/GaAs,' 'cell efficiency calculation for optimization of cell structure,' etc. Presented in the session of the crystal/Si systems were 15 essays which were 'Preparation of textured AR film,' 'Development of amorphous/thin film polycrystalline silicon tandem cell,' 'Development of high efficiency polycrystalline silicon thin-film solar cells,' 'Production of SOG (spin on glass)-Si from metallic grade silicon,' etc. (NEDO)

  13. 28th Solar Energy Promotion Committee Meeting - 3rd Solar Cell Liaison Meeting. Report for fiscal 1990; Dai 28 kai taiyo energy suishin iinkai dai 3 kai taiyo denchi renrakukai. 1980 nendo hokoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-14

    The above events took place in Tokyo in the period May 14-17, 1991, when a total of 89 essays were presented. In relation with the thin film/a-Si systems, 55 presentations were given, which were 'Novel preparation technique termed Chemical Annealing for making a-Si:H with a rigid and stable Si-network,' 'Interface characteristics of a-Si:H films prepared by VHF (very high frequency) plasma CVD (chemical vapor deposition),' 'Preparation of amorphous superlattices by continuous method and characterization of the interface,' etc. In relation with the thin film/compound systems, 8 presentations were given, which were 'Preparation of CuInSe{sub 2} solar cells by selenization method,' 'Deposition of CuInSe{sub 2} films by ICB (ionized cluster beam) technique and their optical characterization,' 'Large-area CdS/CdTe solar cells,' etc. In relation with the crystal/compound systems, 8 presentations were given, which were 'Lattice strain relaxation processes in GaAs grown on Si,' 'Optical transmission studies of tandem solar cells,' etc. In relation with the crystal/Si systems, 18 presentations were given, which were 'Effect of electric field on effective minority carrier lifetime,' 'Computer analysis of surface recombination velocity for high efficiency crystalline silicon solar cells,' etc. (NEDO)

  14. Study of two step constant current charging method with EV`s valve-regulated lead acid batteries for nighttime load leveling; Yakan denryoku wo yuko katsuyo dekiru denki jidoshayo namari denchi no nidantei denryu judenho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ikeya, T.; Mita, Y.; Iwahori, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Iwasaki, M.; Takagi, S.; Sugii, Y.; Yada, M.; Sakabe, T.; Kosaka, E.; Tsuchiya, H.; Kanetsuki, M.; Nasu, H.; Ono, M.; Adachi, K.; Narisoko, H.; Nishiyama, K.

    1997-02-01

    In the constant-current/constant-voltage charging method that has been in application for EV (electric vehicle) lead-acid batteries, power load is generated only at the initial part of the charging process, and therefore the method cannot be said to be sufficiently contributory to the levelling of power loads. In this report, a proposed 2-step constant-current charging method is assessed for applicability, and another charging method is introduced, which extends battery life and utilizes low-cost night-time power more effectively. It is found that the proposed 2-step constant-current charging method (1st step: 12A, 2nd step: 3A) completes the charging process in eight hours, that it assumes a charging pattern more suitable for contributing to the effective use of night-time power than the conventional method, and that it extends the battery life of approximately 170 cycles to approximately 300 cycles. In a study seeking for a charging method capable of utilizing night-time power more efficiently, the 1st-step current of 12A is increased to 30A for shortening the charging time, and then it is found that this change extends the battery cycle life and improves on charging efficiency. The conclusion is that possibilities are high that an increase in the 1st-step current prolongs the battery life cycle and shortens the charting time. 16 refs., 28 figs., 8 tabs.

  15. 31st Solar Energy Promotion Committee Meeting - 6th Solar Cell Liaison Meeting. Report for fiscal 1993; Dai 31 kai taiyo energy suishin iinkai dai 6 kai taiyo denchi renrakukai (1993 nendo hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-04-25

    The above-named events were convened in the period of April 25-28, 1994, when a total of 71 presentations were given on research achievements. Presented in the session on thin film systems were 21 essays concerning the low cost manufacturing technology of low-area modules, development of film substrate a-Si solar cells, etc. Discussed at the symposium were the 'Autonomous development of photovoltaic power generation' and 'Practical application and research and development.' Presented in the session on crystalline Si systems were 17 essays concerning real-time observation of epitaxial growth using STM (scanning tunneling microscope), research on single crystal silicon manufacturing technology, etc. Discussed in the session on international cooperation was 'How international joint research should be.' Presented in the session on systems were 11 essays including the research and development of photovoltaic modules integrated with construction materials. Presented in the session on III-V group systems were 7 essays including the development of crystallized compound solar cell technology. Presented in the session on chalcopyrite II-VI group systems were 9 essays including the development of large area CdS/CdTe solar cell. (NEDO)

  16. Research and development of peripheral technology for photovoltaic power systems. Research and development of redox flow battery for photovoltaic power generation; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo redox denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of redox flow battery for photovoltaic power generation in fiscal 1994. (1) On the production method of electrolyte, silica reduction treatment was attempted to use ammonium metavanadate recovered from boiler as electrolyte of redox flow battery. Silica removal rates more than 90% were achieved by crystallizing V as polyvanadate while keeping molten silica. It was ascertained in minicell experiment that trivalent and quadrivalent V electrolytes produced from recovered V are applicable to continuous charge/discharge operation for one week. (2) On development of battery systems, the relation between battery characteristics and physicochemical properties of carbon fiber electrodes was studied to improve carbon fiber electrodes. The efficiency of 80% was achieved at current density of 160mA/cm{sup 2} by use of layered electrodes, resulting in considerable cost reduction. Performance evaluation operation of the 2kW battery prepared in the last fiscal year was also carried out. 4 figs.

  17. Development of technology for thin substrate polycrystalline solar cells for practical use. Survey on analysis for practical use; Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on the manufacturing technology trend of thin substrate solar cells for practical use in fiscal 1994. In production of Si raw material, as electron beam melting and ingot production are combined, C, P, Ca and Al are removed by evaporation, while Fe and Ti by solidifying segregation. As the basic technology of continuous casting for substrate production, a drop coagulation method for Si melt is under investigation which is more advantageous in unidirectional solidification and cell conversion efficiency than conventional methods. The cost and future of single crystal Si and polycrystal Si were compared on the basis of document survey. Every institute commonly uses FZ substrates to produce single crystal Si cells, and SiO2 for surface passivation. New cell structure, hetero-structure, thin cell, crystalline defect and lifetime are under investigation for ultrahigh-efficiency solar cells. The technology trend was also surveyed through academic societies and conferences. 5 tabs.

  18. Research and development of evaluation system for photovoltaic power generation system. Research and development of evaluation systems for photovoltaic cells and modules; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of the evaluation system for solar cells in fiscal 1994. (1) On development of the performance evaluation method for solar cells, data collection, analysis and measurement of atmospheric conditions necessary for outdoor measurement were carried out to improve the measurement accuracy of laminated solar cells. The validity of measurement methods was verified by comparing experimental results with outdoor measurement ones to improve the indoor measurement accuracy by multiple light source solar simulator. Generated energy in solar cell module level was also studied in field. (2) On development of the reliability evaluation method for solar cells, deterioration data were collected and analyzed by long-term exposure test. As a result, it was clarified that Pmax values are directly affected by seasonal change in air mass, and deterioration of solar cells is hardly found after exposure test for one year, showing a stable state. The characteristic recovery experiment of amorphous solar cell modules was carried out, and the accelerated deterioration test method of thin film cell modules was also studied. 2 figs.

  19. Research and development of evaluation system for photovoltaic power generation system. Survey on research and development of solar cell evaluation system; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on R and D of solar cell evaluation systems in fiscal 1994. The performance/reliability evaluation subcommittee continuously analyzed technical issues and discussed solution measures from the last fiscal year. On development of performance evaluation methods, improvement of measurement accuracy for laminated solar cells is the study issue to be solved. Although laminated solar cells are measured by multiple light source solar simulator, difficult spectrum compensation causes measurement errors. Collection and analysis of data for determining atmospheric conditions, and outdoor measurement experiment under the atmospheric conditions for reference solar light were carried out. The study on incident angle characteristics of laminated solar cells clarified that the deviation from COS characteristics is 1.0% or less at an incident angle of 30{degree}. The study on generated energy in solar cell module level in field clarified that generated energy and generation efficiency are proportional to intensity of solar radiation. 1 tab.

  20. 29th Solar Energy Promotion Committee Meeting - 4th Solar Cell Liaison Meeting. (Report for fiscal 1991); Dai 29 kai taiyo energy suisuin iinkai dai 4 kai taiyo denchi renrakukai. 1991 nendo hokoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-04-21

    The above-named events took place in Tokyo in the period of April 21-24, 1992, and a total of 55 essays were presented. Presented in the session of the thin-film/a-Si systems were 27 essays, which were 'Light-induced degradation and its mechanism in a-Si:H and its multilayers,' 'Light-induced ESR (electron spin resonance) in a-Si{sub 1-x}N{sub x}:H,' 'Distribution of hydrogen surrounding light-induced defects,' 'Equilibration temperature and hydrogen diffusion in a-Si:H,' etc. Presented in the session of the thin-film compound systems were 6 essays, which were 'Local structure studies of CuInSe{sub 2} thin films,' 'Characterization of CuInSe{sub 2} bilayer films fabricated by ICB (ionized cluster beam) techniques,' etc. Presented in the session of the crystal compound systems were 7 essays, which were 'heteroepitaxy of In{sub x}Ga{sub 1-x}As/GaAs,' 'cell efficiency calculation for optimization of cell structure,' etc. Presented in the session of the crystal/Si systems were 15 essays which were 'Preparation of textured AR film,' 'Development of amorphous/thin film polycrystalline silicon tandem cell,' 'Development of high efficiency polycrystalline silicon thin-film solar cells,' 'Production of SOG (spin on glass)-Si from metallic grade silicon,' etc. (NEDO)

  1. Research on fabrication technology for thin film solar cells for practical use. Survey on the commercialization analysis; Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on the technological trend, safety and latest technologies of thin film solar cells in fiscal 1994. As the fabrication technology for amorphous film solar cells, three-electrode plasma CVD was surveyed as fabrication method for high-mobility materials, and hydrogen radical CVD as fabrication method for high-photostable films. Current foreign and domestic reliability tests were surveyed for reliability evaluation of solar cells. In order to ascertain the performance, efficiency, physical properties and optimum structure of polycrystalline Si thin film solar cells, previously reported test results on physical properties such as carrier concentration, carrier lifetime and mobility of films were surveyed together with device simulation results. In addition, technologies for high-efficiency CuInSe2 system and CdTe system solar cells, technologies for cost reduction and mass production, and environmental influence were surveyed. Estimation of production costs for cell modules, and safety of thin film solar cells were also surveyed.

  2. Research and development of peripheral technology for photovoltaic power systems. Study of nickel-hydride storage battery for photovoltaic generation systems; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo suiso denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of nickel-hydride storage battery for photovoltaic generation systems in fiscal 1994. (1) On the study on low-cost electrode materials, the physical properties and electrode characteristics were studied of the prototype hydrogen absorbing alloys prepared by substituting Cu or Ni for Co in Mm(Ni-Co-Mn-Al)5 (Mm: mixture of rare earth elements). The result clarified that it is difficult to reduce Co content in the alloy to 0.4 atom or less. Simple heat treatment and milling processes in production of hydrogen absorbing alloy electrodes were achieved by adopting an improved metal mold and gas atomization method. Characteristics and cycle life of the Ni positive electrode prepared by applying active paste material of Ni(OH)2 were studied, however, the result showed only lives of nearly 300 cycles. (2) On the study on electrode structure for high-performance (long-life) battery, the 3-D porous metal electrode support was evaluated, and various battery configurations were studied. 11 figs., 1 tab.

  3. Valuation of the quantity of electric output from photovoltaic generation system in case of PV module applied to installing to vertical direction; Taiyo denchi wo suichoku ni haichishita baai no hatsudenryo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Miyajima, K [Kansai Electric Power Co. Inc., Osaka (Japan)

    1996-10-27

    In general, it is most efficient and economical to install photovoltaic (PV) modules with proper slope. There are room spaces on the wall except ground or roof. The PV modules were installed on the vertical wall, to consider the compensative method for this weak point. When modules were installed vertically, there is an advantage that reflecting solar light as well as incident solar light can be utilized compared with the installation with slope. The PV modules were installed on the roof of building with inclination of 90{degree} facing to south using the roof material as a reflecting material (S90), and with inclination of 15{degree} facing to south (S15), to compare their output. The output ratio, S90/S15 was 0.42. When it was very fine, this value increased to 0.60. When using plated steel plate as the reflecting material, this value increased to 0.74, which provided 10 to 30% larger output than the roof material. From these results, about 50% of module output of S15 can be expected for S90. If receiving larger reflection, there would only a slight difference in the module output between S15 and S90. 3 figs., 1 tab.

  4. Changes of the temperature coefficients of the characteristics which accompany degradation and recovery of a-Si solar cells; A-Si taiyo denchi no hikari (denryu) rekka oyobi kaifuku ni tomonau tokusei ondo keisu no henka

    Energy Technology Data Exchange (ETDEWEB)

    Yanagisawa, T; Koyanagi, T; Nakamura, K; Takahisa, K; Kojima, T [electrotechnical Laboratory, Tsukuba (Japan)

    1996-10-27

    Pursuant to the measuring of temperature dependency of the characteristics such as conversion efficiency, during the process of degradation in a-Si solar cells due to light and electric current and the process of recovery by annealing, this paper describes changes in temperature coefficients, correlation between the characteristic parameters and the degradation, and the results of the examination of their characteristics. The conversion efficiency {mu} degraded approximately by 45% of the initial value each by the irradiation under a light intensity with 3 SUN accelerated and by the infusion of current at 20mA/cm{sup 2}; and then, the efficiency recovered to 70-75% of the degradation by subsequent annealing. In addition, in the temperature dependency at 80{degree}C against at 20{degree}C, Isc slightly increased while Vcc greatly decreased. This slight increase in Isc was mainly due to the decrease in the width of the forbidden band, while the decrease in Vcc was due to the increase in the reverse saturation current. The temperature dependency of {mu}N was negative, becoming small in accordance with the degradation. The temperature dependency of FF/FFO was negative initially both in light and current, but it decreased with the degradation and turned to positive. The temperature coefficients of I-V parameters reversibly changed corresponding to the degradation and recovery of these parameters and stayed in a good correlation. 7 refs., 8 figs., 1 tab.

  5. Studies of flat-plate solar air collectors with absorber plates made of amorphous silicon photovoltaic modules; Amorphous taiyo denchi module wo shunetsuban to shita heibangata kukishiki shunetsuki no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sato, K; Ito, S; Miura, N [Kanagawa Institute of Technology, Kanagawa (Japan)

    1996-10-27

    A light/heat hybrid air type heat collector has been developed in which heat is collected by solar cell panels. In Type 1 heat collector provided with a glass cover, two modules are connected in series and placed under a glass cover to serve as a heat collecting plate, each module built of a steel plate and two thin-film amorphous solar cells bonded to the steel plate. Air runs under the heat collecting plate. Type 2 heat collector is a Type 1 heat collector minus the glass cover. Air is taken in by a fan, runs in a vinyl chloride tube, and then through the heat collector where it is heated by the sun, and goes out at the exit. Heat collecting performance was subjected to theoretical analysis. This heat collector approximated in point of heat collection a model using a board painted black, which means that the new type functions effectively as an air-type heat collector. Operating as a photovoltaic power generator, the covered type generated approximately 20% less than the uncovered type under 800W/m{sup 2} insolation conditions. Type 1 has been in service for five months, and Type 2 for 2 months. At present, both are free of troubles such as deformation and the amorphous solar cell modules have deteriorated but a little. 4 refs., 9 figs.

  6. 32nd Solar Energy Promotion Committee Meeting - 7th Solar Cell Liaison Meeting. Report for fiscal 1994; Dai 32 kai taiyo energy suishin iinkai dai 7 kai taiyo denchi renrakukai (1994 nendo hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-24

    The above-named events were convened in the period of April 24-27, 1995, when a total of 77 presentations were given on research achievements. In the session on thin type Si polycrystalline systems, 12 essays were presented concerning the thermodynamics of phosphorus and titanium in silicon, etc. In addition, a discussion was held on the 'Technological tasks remaining to be discharged toward industrialization.' In the session on thin film polycrystalline silicon systems, 5 essays were presented and 'Technological tasks related to thin film polycrystalline silicon solar cell' was discussed. In the session on ultrahigh efficiency Si systems, 5 essays were presented and 'Tasks related to the development of ultrahigh frequency single crystal Si solar cell' was discussed. At the symposium, 'Adoption of new energy to be accelerated following the formulation of the New Energy Introduction Guidelines' and 'Outlook for thin film solar cell practical application' were taken up. Various essays were presented and a discussion was held in each of the other sessions on ultrahigh efficiency III-V group systems, thin film chalcopyrite/II-VI group systems, international collaboration, matters related to systems, and thin film a-Si systems. (NEDO)

  7. Reduction reaction of chlorine gas in an Al-Cl2 chemical cell composed of molten chloride salts; Enkabutsu yoyuenkei Al-Cl2 kagaku denchi ni okeru enso gas no kangen hanno kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Konda, S.; Sasaki, T.; Ishikawa, T. [Hokkaido University, Sapporo (Japan)

    1996-10-05

    The molten salt system electrochemical cycle was proposed to reproduce pure Al from scrap Al. The cycle is composed of production of rough AlCl3 by chlorination of scrap Al, refining of rough AlCl3 mainly by sublimation, and electrolytic reproduction of pure Al from refined AlCl3. In production of AlCl3, the Al-Cl2 molten salt system cell composed of anode dissolution reaction of Al and cathode reduction reaction of chlorine gas can generate electric power for the electrolytic reproduction. Chlorine gas can be recycled as anode product. Various experiments were carried out to improve molten salt system cells. In analysis of cell output, voltage drop from open circuit voltage was divided into that due to electrolytic bath resistance, and that due to reaction resistance. The electrolytic bath resistance could be determined from transient characteristics of voltage change just after cutoff of output current. The product of the obtained reaction resistance and a meniscus length was constant regardless of a meniscus length, and useful to predict scale-up cell performance. Output characteristics dependent on meniscus position were also obtained. 16 refs., 11 figs.

  8. 32nd Solar Energy Promotion Committee Meeting - 7th Solar Cell Liaison Meeting. Report for fiscal 1994; Dai 32 kai taiyo energy suishin iinkai dai 7 kai taiyo denchi renrakukai (1994 nendo hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-24

    The above-named events were convened in the period of April 24-27, 1995, when a total of 77 presentations were given on research achievements. In the session on thin type Si polycrystalline systems, 12 essays were presented concerning the thermodynamics of phosphorus and titanium in silicon, etc. In addition, a discussion was held on the 'Technological tasks remaining to be discharged toward industrialization.' In the session on thin film polycrystalline silicon systems, 5 essays were presented and 'Technological tasks related to thin film polycrystalline silicon solar cell' was discussed. In the session on ultrahigh efficiency Si systems, 5 essays were presented and 'Tasks related to the development of ultrahigh frequency single crystal Si solar cell' was discussed. At the symposium, 'Adoption of new energy to be accelerated following the formulation of the New Energy Introduction Guidelines' and 'Outlook for thin film solar cell practical application' were taken up. Various essays were presented and a discussion was held in each of the other sessions on ultrahigh efficiency III-V group systems, thin film chalcopyrite/II-VI group systems, international collaboration, matters related to systems, and thin film a-Si systems. (NEDO)

  9. Report for fiscal 1995 by basic liquefaction technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Delivered at the 1st meeting are a report on the fiscal 1995 research plan and an interim report, involving the use of coal-derived oils, research on refining technology using a PDU (process developing unit), reforming technology and petroleum blending technology for coal-derived oils, development of new reforming catalysts, technology of heterocompound separation, and the development of applications. Reported in relation with the development of environmentally friendly coal liquefaction technology are the study of coal liquefaction conditions, study of the upgrading of basic liquefaction techniques for the improvement and rationalization of the liquefaction process, and a project of liquefaction technology internationalization. A report is also given on a liquefaction catalyst study meeting. At the 2nd meeting, reports are delivered on the development of environmentally friendly coal liquefaction technology, including a briefing on the situation in general, designing of highly active catalysts, elucidation of the mechanism of emergence of activity, achievement of the marginal yield of coal-derived oils, and the properties of catalyst attached to coal. Delivered in relation with the use of coal-derived oils and technology for their refining are a briefing on the situation in general and reports on the blockup to occur in the naphtha fraction process and measures to counter the problem, control of the metamorphosis of active metals in reaction, heterocompound separation technology, and the development of applications. (NEDO)

  10. Investigational report on the trend of control technology; Seigyo gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    For the purpose of corresponding to changes of the industrial structure and making full use of the control technology, the paper investigated the state of the application. High-grade automation in the manufacturing industry has reached the spread of use at big companies for these 10 years. The hierarchical structure of business/process/DCS has been completed, and the optimal control and the advanced control have been realized. The development and spread to the much wider field is anticipated. The soft structure system is needed for equipment improvement in view of the life cycle of equipment and toward the elimination of bottlenecking. For the design of the control system, commercial tools began to be much used, and it is expected in future to accumulate and recycle the knowledge/knowhow for effective design work. Further, strict simulation models based material balance and heat balance have also been on the rise, and the advance in technology is expected. Because of the total productivity of the production equipment, the control technology is anticipated not only for the pursuit of controllability but for the use as supporting technology in the operation/driving/failure diagnosis for working out, carrying out and evaluating the optimum operation plan. 18 refs., 99 figs., 100 tabs.

  11. Report on new energy vision in Koushida Town area; Koushidacho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision was established in the Koushida Town area in Miyagi Prefecture. The population of Koushida Town has leveled off in recent years at 20,245 persons in fiscal 2000. However, number of people working outside the town is increasing, and the ratio of the daytime population is decreasing slowly. Agriculture in this town depends mainly on production rice of such brands as 'Hitomebore' and 'Sasanishiki', wherein the agricultural production amount is 3 billion 260 million yen in fiscal 1998. Commercial activities are decreasing its power with the annual retail sales amount of 17 billion 800 million yen, while the product shipping amount from the attracted factories is on the increasing trend, at 25 billion 700 million yen in 1998. The energy consumption is 526 times 10{sup 9} kcal in total, accounted for by the business department at 42.0%, the transportation department at 32.3%, and the consumer department at 25.7%. The annual utilizable quantity of new energies amounts to 28,816 times 10{sup 6} kcal, made available from solar power, wind power, bio-mass, and refuses, which is about 5.5% of the final energy consumption of the town. The new energy introducing project includes introduction of photovoltaic power generation into the town office building, facilities for interchange of citizens and schools, conversion of the automobiles used in the official organizations into clean energy fueled automobiles, the Eco-town Plan for the east side of Koushida Station, and the project of utilizing bio-mass supplied from the livestock market. (NEDO)

  12. Fiscal 1989 report on the bituminous coal liquefaction section meeting; 1989 nendo rekiseitan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    At the 1st, 2nd, and 3rd group meetings held for the fiscal year, reports are given and discussions are made about the progress of research and development. Reported and discussed in relation to the progress of the pilot plant support research are studies with the 1t/d PSU (process supporting unit) (Nippon Steel Corporation, Mitsui Coal Liquefaction Co., Ltd., and Japan Coal Oil Co., Ltd.); improvement on distillate distribution (Sumitomo Metal Industries, Ltd.); development of an optimum decalcification technique (Sumitomo Coal Mining Co., Ltd., and Sumitomo Metal Industries, Ltd.); studies of solvent hydrogenation catalysts (Sumitomo Metal Mining Co., Ltd., and Chiyoda Corp.); and studies of coal liquefaction conditions (Mitsui Engineering and Shipbuilding Co., Ltd.). In relation to studies using a bituminous coal liquefaction pilot plant, the progress of the 150t/d PP (pilot plant) effort (Japan Coal Oil, Co., Ltd.) and the outlines of pilot surveys (Japan Coal Oil Co., Ltd.) are reported and discussed, the latter covering liquefaction solvent performance optimization, slurry preheating furnaces, coal slurry properties, and so forth. (NEDO)

  13. Report for fiscal 1994 by Coal Gasification Committee; 1994 nendo sekitan gas ka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Summarized in this report is the material already distributed concerning the program for modifying the Nakoso 200t/d pilot plant entrained bed coal gasification furnace. The program aims to verify the overall suitability for power generation use of the air-blow pressurized 2-chamber 2-stage flow entrained bed gasification furnace. Although each specific feature of gasification furnace performance is found to be satisfactory, yet a 100% operation and extended continuous operation remain to be accomplished. Slagging is a phenomenon of ash grains in high-temperature gas adhering to and growing on the furnace walls to block up the furnace to eventually disable the furnace from continuous operation. In view of past achievements and test results, it is found that slagging is closely related to the behavior of floating or molten ash and to the transition temperature range. Various slagging measures have been taken for the current gasification furnace, but they prove to be ineffective. Some drastic measures need to be implemented for improvement. Under study using model furnaces and test furnaces are the reduction of slag generation at its source (re-entrained slag), prevention of adhesion (untrapped slag), removal of slag, optimization of gyration in the furnace, modification of slag properties for enhanced discharge, optimization of the transition gas temperature range, and the modification of furnace dimensions. (NEDO)

  14. Report on new energy vision in Koushida Town area; Koushidacho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision was established in the Koushida Town area in Miyagi Prefecture. The population of Koushida Town has leveled off in recent years at 20,245 persons in fiscal 2000. However, number of people working outside the town is increasing, and the ratio of the daytime population is decreasing slowly. Agriculture in this town depends mainly on production rice of such brands as 'Hitomebore' and 'Sasanishiki', wherein the agricultural production amount is 3 billion 260 million yen in fiscal 1998. Commercial activities are decreasing its power with the annual retail sales amount of 17 billion 800 million yen, while the product shipping amount from the attracted factories is on the increasing trend, at 25 billion 700 million yen in 1998. The energy consumption is 526 times 10{sup 9} kcal in total, accounted for by the business department at 42.0%, the transportation department at 32.3%, and the consumer department at 25.7%. The annual utilizable quantity of new energies amounts to 28,816 times 10{sup 6} kcal, made available from solar power, wind power, bio-mass, and refuses, which is about 5.5% of the final energy consumption of the town. The new energy introducing project includes introduction of photovoltaic power generation into the town office building, facilities for interchange of citizens and schools, conversion of the automobiles used in the official organizations into clean energy fueled automobiles, the Eco-town Plan for the east side of Koushida Station, and the project of utilizing bio-mass supplied from the livestock market. (NEDO)

  15. Research report on human media; Human media no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The human multimedia technology corresponding to users` subjective characteristics was researched to realize information environment producing a sense of unity with human. The human media technology realizes a human sensitive information processing model and a common database easily acceptable sensitively by various users. This technology also should be able to fairly accept and transmit individual`s information and knowledge as multimedia information, and in addition it is required to supply a virtual space with presence. In fiscal 1995, the research committee studied the concrete developmental issue for integrating these advanced fundamental technologies, and as practical images planned the prototype systems such as human media interactive plant operation, supply of environment supporting personal intelligent activities, and virtual medical center. The research committee also discussed development of space mobile media to secure energy-saving and safety of automobiles, and an environment simulation system with participation of many people. 34 figs., 2 tabs.

  16. Report on an analytical survey on the Pacific energy information; Taiheiyo energy joho bunseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of collecting and arranging energy information in the Asia and Pacific region, this survey has been conducted for many fiscal years. The Asia and Pacific region is classified into the Chinese area, the Southeast Asia area including Brunei, Indonesia, the Philippine, Singapore and Thailand, the East Asia area including Japan, Korea, Taiwan and Hong Kong, the North America area including the U.S. and Canada, and the Oceania area including Australia and New Zealand. As to the primary energy supplied from 1980 to 1993, China largely increased its share by 3.1%. The Southeast Asia also increased its share by 2.1%, and the East Asia by 2.5%. To the contrary, the North America area largely declined its share by 7.8%, but still has approximately 60% in the Asia and Pacific area. By kind of energy, coal increased the share while oil decreased. 16 figs., 7 tabs.

  17. Report on energy saving vision in Santo-cho region; Santocho chiiki sho energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    An energy-saving vision was decided on in Santo-cho region in Hyogo Prefecture, with its outline reported. This town is such that about 80% of the region is mountains, forests and wilderness and that aging is advancing at the rate above that of Hyogo Prefecture or the national average. Nearly entire energy of the town is dependent on the supply from outside. The energy consumption is somewhat increasing as a whole, with that of the people's livelihood/domestic sector and of transportation sector are rising. In the classification of fuels, electricity is growing in consumption. As an energy-saving vision, it aimed principally at personal surroundings in which every one got into the habit of saving energy continuously without being forced. The basic plan for the energy conservation drive consisted of inducement to an energy-saving life style, energy conservation to be spread by the next generation children, continuation of energy saving activity rooted in the region, and promotion of energy conservation as a basis for introducing new energy. The diffusion and enlightenment for children destined to lead the next generation were defined as a particularly important assignment, as was the promotion of energy conservation and environmental education. (NEDO)

  18. Survey and research on applications of parallel compiler; Heiretsu compiler tekiyorei ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-31

    An urgent proposition is made that an advanced computing software program development and maintenance system be set up, and activities are conducted in search of strategies and guidelines for the establishment of such a system. Out of recognition that it is important to develop software programs such as operation systems for supercomputers, a survey is conducted of software technology development strategies especially involving application software programs. It is proposed that efforts be positively exerted to develop strategic software developing programs for advanced computing for concentratedly enhancing the development now under way of strategic software programs. In concrete terms, named as strategic software programs to be developed are a next-generation semiconductor TCAD (technology computer-aided design) system, protein structure/function analysis system, fatigue simulation system, next-generation fluid analysis system, chemical reaction simulator, grid computing, and a nanodevice surface analysis system. (NEDO)

  19. FY 1994 report on the Coal Gasification Committee; 1994 nendo sekitan gasuka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper reported activities of the Coal Gasification Committee in FY 1994. The 1st Coal Gasification Committee Meeting was held on May 18,1994, the 2nd Meeting on October 28, 1994, and the 3rd Meeting on February 21, 1995. Report/discussion were made about activities of each section meeting and the progress of the development of coal gasification technology. For the 50 t/d HYCOL pilot plant, disassembly examination was conducted. As a result of the examination, the high-temperature gas corrosion caused by gas product against metal members was negligible, but against members in the wet corrosion environment, SCC, intergranular corrosion and pitting corrosion were generated. About members used in the high-temperature environment, it was made clear that Ir was applicable to thermowell, high chromia-base sintered products were applicable to non-cooling hearth tapping materials, and high chromia-base indeterminate-formed materials were applicable to water-cooled fireproofing wall. Based on the data obtained through the operational study of a 50 t/d pilot plant, conceptual design was made of a coal gasification hydrogen production plant of a scale of demonstration plant. (NEDO)

  20. Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

  1. Proceedings of RITE international workshop on valuation; Total eko balance ni kansuru kokusai workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The RITE International Workshop on Valuation was held in Tokyo and Osaka in February 1996, and eight papers on total ecobalance were reported. In The Field of Impact Assessment, described were constitution and methodology about impact assessment in a wide sense. In LCA Yesterday, Today and Tomorrow, discussed were the historical development and future outlook of LCA. In Standardization of Product Life Cycle Assessment, a survey of the present situation of LCA international standardization was made. In the Relationship between Product Life Cycle Assessment Methodology, considered was the relationship between the goal definition of the product life cycle assessment and the methodological choices. In Valuation in LCA, the present study of LCA was reviewed. Besides, reviews of the LCA study in Japan were made public.

  2. Investigational report on the trend of measures for global warming; Chikyu ondanka taisaku doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To know the trend of measures taken for global warming, conducted were overseas surveys, participation in academic society meetings, and literature surveys. The phaseout time of all ozone depleting substances responsible for the ozonospherial destruction was determined for both developed and developing countries in the 7th Meeting of countries which concluded the Montreal Protocol. As information on measures for protecting the ozonosphere, introduced was activities under United Nations Environment Programme (UNEP). New fluorine containing ethers were introduced as cleaning solvent which causes no ozonospherial destruction and is low in global warming index. Toxicity data were obtained on HFC-236ea and HFC-236fa which are promising substitutes in HCFC foaming and refrigerant fields. The paper introduced an outline of the 1st Meeting of countries which concluded the Framework Convention on Climate Change held in 1995. According to the report on the National Institute of Public Health and Environmental Protection of the Netherlands, the amount of emission of fluorine containing greenhouse effect gas (in CO2 conversion) reached 8-14% of all the amount of greenhouse effect gas emitted in 1990 unless the control is reinforced. An outline of the TEWI-3 project was introduced which is useful for comparing effects of substitution technologies on global warming. 14 refs., 11 figs., 29 tabs.

  3. FY 1993 report on the Material Committee; 1993 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper reported the FY 1993 activities of the Material Committee on the R and D of materials in coal liquefaction, coal gasification, coal utilization hydrogen production, etc. As to metal materials, a PSU implant test on 3Cr-1Mo base high-strength steel was conducted to examine mainly the hydrogen erosion resistance. Concerning surface coatings, aiming at improving the sulfuration corrosion resistance of Al{sub 2}O{sub 3} atmospheric plasma spraying materials, survey of the deterioration with age was made by inserting a test piece in which the structure of coated bed was altered into the PSU reaction tower. Relating to the R and D of trial manufacture of plant use equipment materials, study was made of the evaluation of characteristics of materials for improvement/trial manufacture of gasifier use refractory and the effect of improvement in erosion by coarsening treatment of mullite ceramics. As to the development of the control valve, etc., the control valve was manufactured using sintering diamond as sheet ring material and wolfram carbide as plug material, and the demonstrative test under the actual environment in PSU was carried out. The demonstrative test was also made on slurry flow meter and block valve. (NEDO)

  4. Fiscal 1991 report. Coal liquefaction committee; 1991 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The committee in this fiscal year had the 1st meeting in July 1991, the 2nd in August 1991, and the 3rd in March 1992, when fiscal 1990 research and development results, fiscal 1991 research and development programs, fiscal 1991 research and development results, etc., were reported and deliberated. At the 2nd meeting, the meaning of coal liquefaction technology development and how to go ahead with the task were described, which topic for discussion was entitled 'How coal liquefaction technology should be for the 21st century.' After discussion, it was agreed upon that a coal liquefaction technology package be completed in fiscal 2000 based on the absorption of each other's findings and on the utilization of basic studies common to both to be realized through the exchange of technologies between the brown coal liquefaction project and the bituminous coal liquefaction project. Under the brown coal liquefaction project, a 50 ton/day pilot plant was built and operated in Victoria, Australia, and the operation was completed in October 1990. The results of research and development under the coal brown liquefaction project will be compiled by fiscal 1993. (NEDO)

  5. Report for the coal type committee meetings in fiscal 1988; 1987 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The first committee meeting was held on September 30, 1987. The major agenda included: a development plan for the basic research, and as the summary of the achievements in fiscal 1986, Chinese coal liquefaction tests, coal type surveys, coal resource surveys, and as the research plan for fiscal 1987, coal resource surveys (Alaskan coal and Kalimantan coal), coal type surveys, and Chinese coal liquefaction tests. The results thereon were reported and deliberated. The second committee meeting was held on February 25, 1988. The agenda included: an interim report on the Chinese coal liquefaction tests, coal type surveys, coal resource surveys, (Alaskan coal and Kalimantan coal), as the interim report on the research achievements in fiscal 1987. Among the agenda, especially on the Chinese coal liquefaction tests, the data of the tests performed by the Chinese side and presented at the Japan-China joint technology sub-committee were introduced in detail, having drawn attention of the attendants. The first committee meeting reported the result of the autoclave test carried out by the Chinese side, the result of operation of the small continuous device (0.1 t/d) in fiscal 1986, and the result of the autoclave test performed by Mitsui Engineering and Shipbuilding for comparison. The second committee meeting reported the result of continuous operation implemented in China from August through September 1987 in the Chinese coal liquefaction test. (NEDO)

  6. Quiet STOL research aircraft development program. Teisoon STOL jikkenki kitai kaihatsu sogo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    The airframe development program of the quiet STOL research aircraft (ASKA) promoted by National Aerospace Laboratory, Japan is reported in detail. ASKA was developed based on a C-1 medium-sized troop and freight transport aircraft for the Air Self-Defence Force, and four turbofan- jet engines were substituted for two previous engines. Its first flight was conducted successfully on Oct. 28, 1985 after 8 year development from 1977 to 1985. The ASKA was developed separately on its airframe, engine and flight, and this report includes every related matter to its airframe. The promotion system, budget and executive system are reported in the second chapter, and the design requirements, safety standard and basic design in the third chapter. Several related tests such as wind tunnel test and flight simulation test are reported in the 4th chapter, and the structure and equipment of ASKA are outlined in the final chapter. The appendix includes the line-up of and discussions in the technical committee, the list of newly developed functional parts, the list of design reports and the list of related tests. 50 refs., 8 figs., 23 tabs.

  7. Report on the coal type committee meetings in fiscal 1988; 1989 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    This paper is a report on the coal type committee meetings in fiscal 1988. It summarizes the report mainly on the data distributed at the first and second coal type committee meetings. It describes liquefaction performance tests on Chinese coals in the coal type selection and investigation. In order to develop jointly by Japan and China the coal liquefaction technology, liquefaction tests have been performed on Chinese coals since fiscal 1982 by using the small continuous testing equipment (0.1 t/d) installed in the Beijing Soot and Coal Science Research Institute. The test is now in the third phase. The first sub-committee meeting reported the result on the Shenmu Simengou coal. The coal type investigation has analyzed coal samples collected from the world, classified them into brown coal, sub-bituminous coal of low coal rank, sub-bituminous coal, highly volatile bituminous coal of low coal rank, and highly volatile bituminous coal, and presented a list of candidate coals for liquefaction. Regarding the liquefaction performance tests on Chinese coals, the second coal type committee meeting reported the result on the Fuxin Qinghemen coal, and the result on the Tianzhu coal as revealed by using the NEDOL process BSU. The paper also presents the interim report on the research achievements in fiscal 1988 on the liquefaction performance tests on Chinese coals and the research achievements of the investigation and study in fiscal 1988 on the treatment technologies for coals used for coal gasification 'coal type selection and investigation'. (NEDO)

  8. Report on the material committee meetings in fiscal 1987; 1987 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The material committee has held two meetings in this fiscal year. The first committee meeting (September 25, 1987) was held for the major agenda of (1) the development of a centrifugal slurry pump for liquefaction plants, and as the research and development in fiscal 1987, the in-plant tests on new materials and the development a let-down valve, which were reported and deliberated. The major agenda of the second committee meeting (February 24, 1988) were, as the summarized achievements in fiscal 1987, (2) development of a technology to manufacture hydrogen by utilizing coal, (3) in-plant tests on new materials, and (4) development of a let-down valve, which were reported and deliberated. In Item (1), wear in the shaft seal of the centrifugal slurry pump was discussed regarding its cause from the result of a contraction flow test. In Item (2), it was verified that picrochloromite and chromia are integrated as an electromelting aggregate for the atmospheric stability of refractories used in a gasification furnace, and that the test conditions for the refractories call for the refractories to be tested under severe conditions. In Item (3), how to proceed the tests in the future was verified on such items as corrosion patterns, tested materials, coal types, and the degree of corrosion. In Item (4), kinds and temperatures were verified on slurries used in the water-slurry wear test and the fretting corrosion test. (NEDO)

  9. FY 1994 report on the Coal Liquefaction Committee; 1994 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper reported the FY 1994 activities of the Coal Liquefaction Committee. The Coal Liquefaction Committee in this fiscal year was held on November 29, 1994 (1st) and March 22, 1995 (2nd), and report was made on the bituminous coal liquefaction study and state of the R and D of liquefaction base technology. Report was also made on the state of construction of bituminous coal liquefaction PP, outline of the results of the PSU operation, outline of the 11th Japan-U.S. JTM, etc. In the liquefaction base study, report/discussion were made about the improvement/rationalization of liquefaction process, study of innovative technology of coal liquefaction, study of coal liquefaction conditions, study for higher liquefaction element technology, project on the internationalization of coal liquefaction technology, etc. As to the relation of the entrained bed coal gasification power plant, report/discussion were made about survey/study on the processing of coal for coal gasification use (survey of coal kind selection, development of information processing system for coal conversion technology). Besides, as a topic, report was made on the economical evaluation/calculation of a commercial plant for brown coal liquefaction. (NEDO)

  10. FY 1991 report on the Coal Gasification Committee; 1991 nendo sekitan gasuka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The paper reported activities of the Coal Gasification Committee, gasification power generation section and gasification technology section in FY 1991. The 1st Coal Gasification Committee Meeting was held on July 16,1991, and report/discussion were made about an outline of the FY 1991 research plan on the development of coal gasification technology. The 2nd Meeting was held on March 12, 1992, and report/discussion were made about activities of each section meeting and the progress of the development of coal gasification technology. In the section meeting of coal gasification power generation, report/discussion were made about the progress and study object of the development of entrained bed coal gasification power plant and support study for the development of the plant. In the 1st section meeting of coal gasification technology, as to the developmental plan on coal utilization hydrogen production technology, report/discussion were made about design/construction/operational study of pilot plant and support study for pilot plant (study using small equipment, study of trial manufacture of plant use equipment/materials). In the 2nd section meeting, report/discussion were made about the results of the development of coal utilization hydrogen production technology. (NEDO)

  11. Report on the coal liquefaction committee in fiscal 1992; 1992 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the coal liquefaction committee in fiscal 1992. The first committee meeting was held on August 21. After having confirmed the minutes of the previous meeting, an explanation was given on the research and development plans in fiscal 1992. The explanation covered the general explanation, bituminous coal liquefaction, brown coal liquefaction, and the common and fundamental aspects. The presented topics included the achievements in the operations using a bituminous coal liquefaction PSU and a small device, the status of compiling the achievements in the brown coal liquefaction project, preparation of the basic policy on developing the common basic technologies, and structuring of a coal liquefaction technology package. The second meeting was held on March 18, 1993. The meeting verified the minutes of the previous meeting, and gave the sub-committee reports for fiscal 1992. The sub-committees include those for bituminous coal liquefaction, brown coal liquefaction, environmental safety evaluation, and separation and refining technologies. As the summary of the achievements in fiscal 1992, descriptions were given on the bituminous coal liquefaction, brown coal liquefaction, and common and basic aspects. The fiscal 1993 plan presented included the budget aspect. A description was given as a topic on the economic performance evaluation and the working scheme (the execution plan) for the brown coal liquefaction process. (NEDO)

  12. FY 1989 report on the Coal Kind Committee; 1989 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The paper reported the FY 1989 activities of the Coal Kind Committee. The Coal Kind Committee in this fiscal year was held on July 24, 1989 (1st) and on February 21, 1990 (second), and report/discussion were made about the performance test on liquefaction of Chinese coal, survey of coal kind selection and international standards of coal. As to the performance test on liquefaction of Chinese coal, comparison was made between the results of the re-analysis/detailed analysis of the coal-derived liquids of Liaoning Province and Inner Mongolia in China which were tested at BSU in Beijing in this fiscal year and the results of the liquefaction test of the coal of Gansu Province in China which was made at BSU in Japan and BSU in China, and the discussion was actively made. Relating to the coal kind survey, report was detailedly made on the automatic analysis of maceral. The analysis of coal maceral requires time and skills, and to make it promptly and universally, the points to be cleared up, handling of two kinds of vitrinite, etc. were made clear. About the international standards of coal, the paper reported on the progress of the international conference held in Sidney in November 1988. (NEDO)

  13. Report on the coal type committee meetings in fiscal 1988; 1989 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    This paper is a report on the coal type committee meetings in fiscal 1988. It summarizes the report mainly on the data distributed at the first and second coal type committee meetings. It describes liquefaction performance tests on Chinese coals in the coal type selection and investigation. In order to develop jointly by Japan and China the coal liquefaction technology, liquefaction tests have been performed on Chinese coals since fiscal 1982 by using the small continuous testing equipment (0.1 t/d) installed in the Beijing Soot and Coal Science Research Institute. The test is now in the third phase. The first sub-committee meeting reported the result on the Shenmu Simengou coal. The coal type investigation has analyzed coal samples collected from the world, classified them into brown coal, sub-bituminous coal of low coal rank, sub-bituminous coal, highly volatile bituminous coal of low coal rank, and highly volatile bituminous coal, and presented a list of candidate coals for liquefaction. Regarding the liquefaction performance tests on Chinese coals, the second coal type committee meeting reported the result on the Fuxin Qinghemen coal, and the result on the Tianzhu coal as revealed by using the NEDOL process BSU. The paper also presents the interim report on the research achievements in fiscal 1988 on the liquefaction performance tests on Chinese coals and the research achievements of the investigation and study in fiscal 1988 on the treatment technologies for coals used for coal gasification 'coal type selection and investigation'. (NEDO)

  14. Proceedings of Japan-Germany Workshop of Bioremediation; Nichidoku bio remediation workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-04

    This is a proceedings of Japan-Germany Workshop on Bioremediation held on December 4 and 5, 1995. The keynote lectures include `Environmental preservation using biotechnology` by Prof. Karube of University of Tokyo, and `Environmental technology in Germany: status, achievements, and problems` by Prof. R.D.Schmid of University of Stuttgart. In the oral session, 7 papers are presented in the microbiological aspects of bioremediation, 10 papers in the environmental monitoring, and 6 papers in the engineering aspects of bioremediation. This workshop was sponsored by the German Federal Ministry for Education, Science and Technology, New Energy and Industrial Technology Development Organization, and Research Institute of Innovative Technology for the Earth. According to the lecture by Prof. Karube, key technologies for the environmental preservation include biotechnologies, such as the culture of fine algae with high CO2 concentration resistant properties using a solar light condenser, production of effective substances from CO2, and production of organic fertilizer from the sediments of lakes and sea. 19 refs., 12 figs., 3 tabs.

  15. Fiscal 1990 report on the bituminous coal liquefaction section meeting; 1990 nendo rekiseitan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    At the 1st, 2nd, and 3rd group meetings held for the fiscal year, reports are delivered and discussions are made concerning the progress of research and development activities. Reported and discussed in relation to the pilot plant support research, etc., are studies with the 1t/d PSU (process supporting unit) (Nippon Steel Corporation, Mitsui Coal Liquefaction Co., Ltd., and Japan Coal Oil Co., Ltd.); development of an optimum coal refining technique (Sumitomo Coal Mining Co., Ltd.); development of an optimum pretreatment technique and improvement on distillate distribution (Sumitomo Metal Industries, Ltd.); studies of coal liquefaction conditions (Mitsui Engineering and Shipbuilding Co., Ltd.); and studies of solvent hydrogenation catalysts (Sumitomo Metal Mining Co., Ltd., and Chiyoda Corp.). Reported and discussed in relation to researches using a bituminous coal liquefaction pilot plant are the progress of the 150t/d PP (pilot plant) effort (Japan Coal Oil Co., Ltd.) and the outlines of pilot surveys (Japan Coal Oil Co., Ltd.), the latter covering liquefaction solvent performance optimization, slurry pre-heating furnaces, coal slurry properties, and so forth. (NEDO)

  16. Fiscal 1995 report. Liquefaction key technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The subcommittee held the 1st meeting in September 1955 and the 2nd in March 1996, when fiscal 1995 research plans and research results were introduced and deliberated. In the study for designing a high-dispersion catalyst and the elucidation of the mechanism of activity expression, catalysts of highly dispersed iron supported on the brown coal surface in various ways were compared with each other in terms of liquefaction activity. Furthermore, geometric changes in the iron catalyst during the sulfurizing process were examined using the XRD (X-ray diffraction) and TEM (transient electromagnetic) methods. An improved catalyst was found to achieve a liquefaction yield near the Yallourn coal liquefaction limit in a high boiling solvent system. Concerning the study of coal oil product applications and refining technologies, reports were delivered on research results relating to the problem of blocking to occur during naphtha fraction refining and measures therefor, inhibition of active metal geometric changes during reaction, methods for separating hetero-compounds from coal oil and application thereof, and so forth. (NEDO)

  17. Report for fiscal 1995 by Coal Gasification Committee; 1995 nendo sekitan gas ka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This is a summary primarily of the distributed material. As of December 14, 1995, the 200t/d pilot plant for power generation by entrained bed coal gasification records a total coal gasification operation time of 4,485 hours with an accumulated amount of power generation of 9,227MWh. A large combustor is tested, and it is found that combustion is stable under a 1/4 load with low NOx emissions. The combustor is sufficiently cooled with a small supply of air. Coal ash and coal, supplied in a constant state for an improved heat recovery efficiency in the development of hydrogen-from-coal technology, are heated to a temperature near their melting points. They are then allowed to impinge at a heat transfer plane simulating a gasifier heat recovery section, and a study is made of the mechanism of ash adhesion, molten or semi-molten, to the heat recovery section. The reduction of the heat transfer coefficient due to added grains is 30-50%, and the reduction is small when the heat transfer pipe surface velocity is high or when the carbon concentration in the grains is high. In another effort, utilization of coal-derived gas as town gas is studied. As for yields as indicated by the Curie gas pyrolyzer, the gas yield increases and liquid yield decreases when the reaction temperature is high. Using a small test unit, it is found that a rise in the hydrogen partial pressure increases the production of both gas and liquid. (NEDO)

  18. FY 1990 report on the Material Committee; 1990 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    The paper reported the FY 1990 activities of the Material Committee on the R and D of materials in coal liquefaction, coal gasification, coal utilization hydrogen production, etc. As to the development/assessment of new materials for plant use, the sulfuration corrosion resistance was confirmed of aluminum diffusion coated agent and aluminized materials. Further, in the measurement of hydrogen permeability of the test piece exposed for 500 hours to the sulfuration corrosion environment, a good hydrogen permeation control effect was confirmed of hot-dipped materials and SiC/TiC plasma CVD materials. As to the development of the control valve, etc., CVD coating of Ti (C, N) and sintering diamond indicated good erosion resistance in the high speed water slurry injection test. Further, in the high speed powder injection test, PVD coating of TiN and sintering diamond indicated good erosion resistance. As to the development of the coal utilization hydrogen production technology, the following were carried out: improvement of gasifier use materials, assessment of materials under the corrosive environment where coal slag exists, experimental study on the repair technology, etc. (NEDO)

  19. Report for the coal type committee in fiscal 1992; 1992 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the coal type committee in fiscal 1992, and summarizes the main technological achievements. In the Chinese coal liquefaction test, fiscal 1991 has performed liquefaction tests on Fushun coal by using a small continuous testing facility (0.1 t/d) at the Coal Chemistry Research Institute in Beijing. Fiscal 1992 has completed the liquefaction tests on Shengli coal. In October, a liquefaction test was carried out by using Tianzhu coal according to the NEDOL process. This paper reports the result of the liquefaction test on the Shengli coal, and the result of the analysis on the Fushun coal liquefied oil. The coal type selection and investigation having been performed to date reveals close correlation among the maceral composition of coal, coal rank and liquefied oil yield. Coals having good reactivity and suitable for liquefaction are generally suitable also for gasification. In the pretreatment of coal as a gasification material for hydrogen manufacture, a test was performed by using A heavy oil and tar sand bitumen plus A heavy oil as the granulating agents. With Montana coal, the highest de-ashing rate was achieved when the oil was added at 35% by weight. Both of the reaction rate and oil yield were improved. A handling test was carried out up to 72.5 degrees C, wherein Tatung coal presented no problems in both of the discharging and sticking tendencies. (NEDO)

  20. FY 1992 report on the Coal Kind Committee; 1992 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper reported the FY 1992 activities of the Coal Kind Committee. The Coal Kind Committee in this fiscal year was held on September 28, 1992 (1st) and on March 4, 1993 (second), and report/discussion were made about the performance test in Chinese coal liquefaction, survey of coal kind selection, development of handling technology, etc. As to the performance test in Chinese coal liquefaction, there were the data very different in quality among the data, and it was pointed out that it was necessary to make a close re-examination of sites for sample collection and sampling methods. Relating to the survey of coal kind selection, the following were pointed out: The inertinite value in the maceral analysis was not necessarily in agreement with the reactivity; The inertinite was dependent largely on temperature for the reaction; It was necessary to make parameters based on the chemical structure. As to the development of the coal utilization hydrogen production technology, the paper reported the experimental survey of coal pretreatment, development of new deheterocyclicity and deashing technologies, experimental survey of coal handling, etc. (NEDO)

  1. Fiscal 1993 report. Coal liquefaction committee; 1993 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The committee in this fiscal year had the 1st meeting in July 1993, the 2nd in December 1993, and the 3rd in March 1994, when fiscal 1993 research and development programs and results were reported and discussed. Reported and discussed at the 2nd meeting were the compilation of brown coal liquefaction technology development project results, evaluation report on the same, hydrorefining of oil from brown coal and the research and development of application technologies for the same, and an environmental safety evaluation test on the same. In selecting a standard coal for the operation of the 150 ton/day pilot plant, PSU (process supporting unit)-aided studies were made on the analytical values presented by coals, yield of the liquid, yield of the liquefaction residue, yield of the generated gas, amount of the hydrogen consumed, coal oil properties, liquefaction residue properties, operationality, etc. On-site investigations were conducted also in Indonesia, and a conclusion was reached that Tanito Harum coal would be the most suitable for the pilot plant. Concerning the liquefaction catalyst for the pilot plant, a report was given on a comparison made between the activity of a synthetic iron sulfide and that of natural pyrite. (NEDO)

  2. Fiscal 1994 report. Liquefaction key technology subcommittee; 1994 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The subcommittee held the 1st meeting in August 1994 and the 2nd in March 1995, when preceding fiscal year's research results, fiscal 1994 research plans, fiscal 1994 research results, etc., were introduced, and deliberated. In the study of hydrorefining of naphtha, kerosene, and light oil fractions, a nitrogen concentration level of not more than 5 ppm was achieved by refining oils from Indonesian coal. Studies were also made about the two-step hydrorefining system, the relationship between the coal oil refining level and sludge formation, etc. In the research for the development of novel catalysts for upgrading coal oil, the active life of a nickel-supporting catalyst for hydrogenation at the 1st step was somewhat prolonged with an increase in the amount of nickel. In the study of coal liquefaction conditions, an AWIP method was deliberated, wherein liquefaction process waste water was utilized as one of catalytic component adjusting materials. For upgrading liquefaction key technologies, studies were made for catalyst improvement and pretreatment method development, and about the behavior of liquefaction reaction in a high boiling solvent-aided process. (NEDO)

  3. Report on the analytical survey of the Pacific energy information; Taiheiyo energy joho bunseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Arrangement, investigation and analysis of an energy information exchange system were conducted, with the aim of coping with the development in the whole Asia/Pacific area, the stabilization of energy supply/demand, and the environmental problem and of realizing effective cooperation of every country in the area. Concerning the trend of the domestic primary energy supply/demand, there are some patterns. Countries which show high growth rates are developing countries such as Thailand and China, and NIES such as Korea and Taiwan. Countries where growth rates are slowing down and lowering are developed countries such as Australia, Canada, Japan and the U.S. Countries where energy supply/demand is not stabilized are Singapore, Hong Kong, Indonesia and Chile which are suffering from variations in import/export. The ultimate energy consumption is the domestic primary energy supply from which the conversion loss in the conversion sector was deducted, and indicates almost the same trend as the primary energy supply. It is divided into a stabilized type of developed countries and a rapidly increasing type and a stagnant type. However, there are some exceptions. Total data in the quarter of the year cannot be the yearly data by itself, but requires a year-end tax arrangement. 40 tabs.

  4. Report on regional new energy vision for Kahoku town; Kahokucho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A regional new energy vision has been formulated for Kahoku town, Kochi Prefecture, which features the introduction of recoverable energy harmonious with nature and friendly to human life and environments. The results of activities conducted in this connection are compiled into nine chapters, which cover (1) Kahoku-town's local characteristics relative to new energy, (2) survey of townspeople's awareness of new energy, (3) amounts of new energy in existence, (4) basic policy toward introduction, (5) study of concrete measures for promoting introduction, (6) study of prioritized projects, (7) establishment of target amounts for introduction, (8) coordination with energy conservation measures, and (9) a system for thrusting forward the regional new energy vision toward embodiment. Chapter (7) comprises the way of setting target values for introduction; study of the target values to be achieved by the industry, administration, and citizenry, respectively; and a conclusion on the target values. Studies are conducted in the chapter about the introduction of solar energy, wind power generation, small scale hydroelectric power generation, cogeneration, clean energy vehicles, and the like. It is predicted that 960 kl/year will be introduced in fiscal 2010 in terms of oil, which accounts for 12% of energy consumption. (NEDO)

  5. Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

  6. Achievement report for fiscal 1998. Optical tomographic system; 1998 nendo seika hokokusho. Hikari danso imaging system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Evaluations were given on spatial resolution and measurement time of an optical tomographic system by using the developed 64-channel time-resolved spectroscopy and an image reconstruction algorithm. With respect to the spatial resolution, the target value of 1 cm was verified from tomographic images of a phantom with a diameter of 10cm, simulating a neonate. The measurement time achieved 20 minutes, being one third of the target value. In installing the equipment at Hokkaido University, speeds of the optical switches and attenuators were increased to have reduced the measurement time to one minute. For installation at Kanagawa Rehabilitation Center, development has been made on a nano-second light pulser, whose average beam quantity has been increased to 40 times, and improvement has been given on the optical switches, the attenuators, and the indication software, by which the measurement time was decreased further by 30 seconds than that at Hokkaido University. In performing the clinical evaluation, the evaluation protocol resolved by the Experiment Evaluation Special Committee was submitted for deliberation at the Medical Welfare Device Clinical Evaluation Committee. Upon having been authorized by the Committee, the clinical evaluations were performed at Hokkaido University and the Kanagawa Rehabilitation Center. (NEDO)

  7. Research report for establishment of NEDO vision; NEDO vision no sakutei ni muketa chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Because of an increase in energy demand due to economic growth and industrial structure change in the Asian area and its effect on global environment, the economic evolution harmonizing with energy and environment (3E) of the Asian area is required. The role of Japan, in particular, NEDO for achieving such 3E was studied from an international viewpoint. The following are thus surveyed: The history of energy demands, economic growth, an increase in energy consumption and their effect on global environment in the Asian area, and the policies, measures and future plans of Asian countries corresponding to the above situations. The role of NEDO is first of all R & D of biomass toward practical use, and development of effective use technology of biomass energy. Positive approach to control of CO2 emission and immobilization of CO2 is also required in industrial and traffic fields. As technology transfer from Japan, promotion of joint researches and establishment of an economic support scheme are expected together with transfer of the basement technology and training. 79 figs., 13 tabs.

  8. FY 1992 report on the Coal Liquefaction Committee; 1992 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper reported activities of the Coal Liquefaction Committee in FY 1992. In the 1st committee meeting, report/discussion were made of the summary of the FY 1992 R and D plan on the bituminous coal liquefaction, brown coal liquefaction and the common/basic technology. Further, the following were reported as topics: results of the operation by bituminous coal liquefaction PSU and small equipment, state of arrangement of the results of the brown coal liquefaction project, making of the basic policy for development of the common/basic technology, construction of package of coal liquefaction technology. In the 2nd committee meeting, the summary of the results of the FY 1992 R and D was reported/discussed. As to the development of bituminous coal liquefaction technology, study using pilot plant and support study were reported. Concerning the development of brown coal liquefaction technology, study using a 50t/d pilot plant and complementary study of operation. Relating to the development of the common/basic technology, trial manufacture/development of plant equipment/materials, survey of selection of coal kind, etc. The paper also reported a scheme on the evaluation of efficiency of the brown coal liquefaction process. (NEDO)

  9. Report on new energy vision in Fudai Village area; Fudaimura chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision was established in the Fudai Village area in Iwate Prefecture. The population of Fudai Village is decreasing from the peak of 4,103 persons in 1985. Its basic industry is fishery and agricultural industries, with the fish and marine product raising industry particularly active. The energy consumption in Fudai Village is, in the decreasing order, the transportation field (48.5%), the social and household field (26.5%), social industry, and manufacturing industry. Homes consume room heating energy at a greater extent. Energies are supplied by fuel oil at 53,554 Gcal (79.3%) and electric power at 11,551 Gcal (17.1%). The new energy introducing project has discussed introduction of cogeneration into the Kurosaki House, introduction of photovoltaic power generation and solar heat utilization systems, and introduction wind power generation as a tourism symbol. Discussions were also given on conversion of the automobiles used in the official organizations into clean energy automobiles. Further discussions were given on introduction of small new energy facilities, such as hybrid illumination, small wind power generation, and photovoltaic power generation, into the village office, the station square, the fish market, facilities in the fishing port, the children's hall, and the Road Station. (NEDO)

  10. FY 1981 report on the Coal Kind Survey Committee; 1981 nendo tanshu chosa iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    For the purpose of establishing coal liquefaction/gasification technology, investigational survey on the usable coal resource in Japan was made to collect/file the data on the state of coal existence, coal kind, etc. by the Coal Kind Survey Committee and the section. In the 1st committee meeting, an idea of the coal kind survey was discussed, and in the 2nd committee meeting, a summary of activities in this fiscal year was reported. In the section meeting, the following were carried out: discussion of a course of the coal kind survey in the 1st meeting; discussion about how to proceed with the coal kind survey/items of data filing in the 2nd meeting; examinational study of items of data filing in the 3rd meeting; summary of activities in this fiscal year in the 4th meeting. As examples of the coal kind survey, the following were cited: special study report on coal resource and gasification/liquefaction characteristics by Science and Technology Agency; results of the survey by Joint Coal Board and Queensland Coal Board in Australia; Report of 1978 by The Fuel Society of Japan; Report of 1976 by Pennsylvania State University; data on process raw coal by The Iron and Steel Institute of Japan, etc. (NEDO)

  11. Coal liquefaction committee report for fiscal 1981; 1981 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    For the assurance of smooth progress of coal technology development endeavors, the New Energy and Industrial Technology Development Organization (NEDO) has installed coal technology development committees (general committee on coal technologies, coal liquefaction committee, plant materials committee, coal type survey committee, total system committee, and coal gasification committee). The coal liquefaction committee deliberates and evaluates liquefaction technology and propels forward smoothly the efforts to develop the technology. Under the coal liquefaction committee, there are four subcommittees, which are the 1st subcommittee (primary liquefaction subcommittee), 2nd subcommittee (solid/liquid separation subcommittee), 3rd subcommittee (secondary hydrogenation subcommittee), and the 4th subcommittee (brown coal liquefaction subcommittee). The 2nd and 3rd subcommittees deal with common tasks as they were studied in fiscal 1980. The 1st subcommittee incorporates into itself the old subcommittees that respectively worked on the three liquefaction processes (the direct hydrogenation process, the solvent extraction process, and the Solvolysis process), and is designed to provide a site for information exchange. A brown coal liquefaction committee is incorporated into the coal liquefaction committee as the 4th subcommittee. This report is a compilation of the agendas of the respective subcommittees of the coal liquefaction committee. (NEDO)

  12. Fiscal 1991 report on the brown coal liquefaction section meeting; 1991 nendo kattan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    At the 1st through 5th brown coal liquefaction group meetings held for the fiscal year, reports are delivered and discussions are made about the progress of research and development. At the 1st meeting, a fiscal 1991 brown coal liquefaction research plan is introduced, and discussed. At the 2nd meeting, an interim report on the brown coal liquefaction technology development project is discussed. At the 3rd meeting (a joint meeting of the brown coal and bituminous coal liquefaction groups), an agendum entitled 'what the development of brown/bituminous coal liquefaction technologies for the 21st century should be' is reported, and discussed. At the 4th meeting, reports are made on the results of deliberation at the Industrial Technology Council, progress of the follow-up study, progress of the collection of achievements, and so forth. At the 5th meeting, the outline of the follow-up study, the collection of achievements in the pilot plant study (a project report preparation schedule and materials evaluation), the progress of pilot plant dismantling work, etc., are reported and discussed. (NEDO)

  13. Report on studies on closed cycle MHD power generation; Closed cycle MHD hatsuden kento hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Summarized herein are results of the studies on closed cycle MHD (CCMHD) power generation by the study committee. The studied system is based on the MHD gas turbine combined Brayton cycle of about 500,000 kW in output power, firing natural gas as the fuel, and the conceptual design works therefor are completed. The major findings are: the overall plant efficiency: 54.2% at the power transmission side, plot area required per unit power output: 0.04 m{sup 2}/KW, unit construction cost: 251,000 yen/KW, and unit power generation cost: 10.2 yen/KWh. This system will be more operable than the gas turbine combined cycle with steam system, because start-up time, output change rate, optimum load and so on are constrained not on the power generator side but on the gas turbine side. The expected environmental effects include the exhaust gas NOX concentration being equivalent with that associated with the conventional power generator of 2-stage combustion system, quantity of combustion gases to be treated being approximately 40% of that associated with the gas turbine combined cycle, and reduced CO2 gas emissions, resulting from enhanced power generation efficiency. It is expected that the CCMHD system can exhibit higher efficiency than the high-temperature gas turbine combined cycle system. (NEDO)

  14. Fiscal 1989 report. Coal liquefaction committee; 1989 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The committee in this fiscal year had its 1st meeting in June 1989 and 2nd meeting in March 1990, when fiscal 1989 research and development programs and fiscal 1989 research and development results, etc., were reported and discussed. The operating status of the 1 ton/day PSU (process supporting unit) for bituminous coal liquefaction was reported and discussed. The report included its 1st operation for the demonstration of a long-term stable run under standard conditions that continued for trouble-free 50 days, the 2nd operation for the investigation of the effect of liquefaction reaction temperature in which the liquefaction yield recorded the maximum at 450 degrees C with the collection of coal oils of 55 wt.% on the average, and the 3rd operation for the investigation of the effects of liquefaction reaction pressure and catalyst injection size whose details were being analyzed. Reported in relation with the brown coal liquefaction pilot plant was a comprehensive operation of a series of 1st hydrogenation, solvent deashing, and 2nd hydrogenation processes completed after a continuous operation of 460 hours establishing a total operating time of 1050 hours. (NEDO)

  15. Coal rank survey committee report for fiscal 1981; 1981 nendo tanshu chosa iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    A coal type research project is started under which data concerning the coal resources that Japan can make use of are to be gathered, which are necessary for determining their fitness-for-use in a coal liquefaction or gasification process, and the gathered data are to be compiled into files which are easy to use. As for the buildup of a computer-aided data bank, since the number of coal types is not yet large, only part of the data is taken into consideration this fiscal year. In the study of compiling the data into files, it is decided that the files be divided into two categories, one for grasping the status of the development project as a whole and the other for defining the positions of the individual coal specimens. Provided in the former are outlines covering the name of coal mine or project, location, entrepreneur, states of the mining area and geology, state of production, infrastructure-related matters, etc. Described in the latter are the details that enable the identification of given specimens such as the coal bed or coal brand, location and method of collection, collector, date, amount of the specimen, method of treatment, etc. (NEDO)

  16. Report for the coal type committee meetings in fiscal 1993; 1993 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This paper reports a joint meeting of the coal liquefaction committee and the coal type committee in fiscal 1993. The report is focussed on the coal type selection (the final report) for the coal used in the 150-t/d coal liquefaction pilot plant (PP) among other agenda. Initially the Australian Wandoan coal was scheduled to be selected as the reference coal for the PP operation, but the mine has not gone into operation, hence the schedule was given up. Screening was carried out to select a coal which is commercially produced and exported, and contains ash at 10% by weight or less, sulfur at 1.5% by weight or less, and chlorine at 300 ppm or less. An autoclave and a 0.01-t/d flowing type device were used to evaluate liquefaction performance, whereas the Tanito Harum coal produced in Indonesia, very similar to the Wandoan coal, was selected as a promising candidate. A PSU was used to demonstrate overall operation performance. The coal is an appropriate reference coal as seen from the aspects of liquefied oil yield, nature, operability, and site surveys in Indonesia. Among the actual record of four kinds of PSU coals in the past, the present coal has the oil yield ranked high, has the least liquefaction residues, and is advantageous economically. The oil yield per ton of coal has cleared the PP target of four barrels. The coal has less ash, is easy in solid/liquid separation in the depressurized distillation, and has no problems in operability, excepting the matter of coal supply. (NEDO)

  17. Report on Seminar on Clean Coal Technology '93; Clean coal technology kokusai seminar hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-11-01

    The program of the above clean coal technology (CCT) event is composed of 1) Coal energy be friendly toward the earth, 2) Research on CCT in America (study of coal structure under electron microscope), and 3) Research on CCT in Australia (high intensity combustion of ultrafine coal particles in a clean way). Remarks under item 1) are mentioned below. As for SO{sub 2} emissions base unit, Japan's is 1 at its coal-fired thermal power station while that of America is 7.8. As for the level of SO{sub 2}/NOx reduction attributable to coal utilization technologies, it rises in the order of flue gas desulfurizer-aided pulverized coal combustion, normal pressure fluidized bed combustion, pressurized fluidized bed combustion, integrated coal gasification combined cycle power generation, and integrated coal gasification combined cycle power generation/fuel cell. As for the level of CO2 reduction attributable to power generation efficiency improvement, provided that Japan's average power generation efficiency is 39% and if China's efficiency which is now 28% is improved to be similar to that of Japan, there will be a 40% reduction in CO2 emissions. Under item 2) which involves America's CCT program, reference is made to efforts at eliminating unnecessary part from the catalytic process and at reducing surplus air, to the export of CCT technology, and so forth. Under item 3), it is stated that coal cleaning may govern reaction efficiency in a process of burning coal particles for gasification. (NEDO)

  18. FY 1991 report on the bituminous coal liquefaction section; 1991 nendo rekiseitan ekikabukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The paper reported activities of the bituminous coal liquefaction section in FY 1991. In the 1st bituminous coal liquefaction section meeting, report/discussion were made on the outline of the plan on the FY 1991 research using pilot plant and the support study of pilot plant. In the 2nd section meeting, report was made on 'How the development of coal liquefaction technology should be in the 21st century,' a report made by the joint section of bituminous coal/brown coal liquefaction. In the 3rd section meeting, report/discussion were made on the state of progress of the FY 1991 R and D and results. In the study using the bituminous coal liquefaction pilot plant, report was made on the outline of construction of a 150t/d pilot plant, study on the acquisition of material balance, analytical study of the data on liquefaction tower, testing survey on properties of coal slurry, and testing survey on slurry preheating furnace. In the support study of pilot plant, report was made on the study using 1t/d PUS, study on the development of the optimum coal refining technology and improvement in the distillate distribution, study of conditions for coal liquefaction and study of solvent hydrogenation catalyst. (NEDO)

  19. Assessment report on the development of functionally inclined material; Keisha kinosei zairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Concerning a project whose aim is to develop heat resistant engine members through the application of the concept of functionally inclined materials, deliberation and assessment are made of the meaning of its implementation, validity of the research program, research achievement, etc. The project deals with a specimen, diameter 150mm or more and thickness 5mm or more, built of a zirconia/stainless steel-based functionally inclined material, and its goal is to develop technologies for optimizing the baking process for the said specimen, baking system and related devices, assessment technique, tribological assessment technique, etc., and it is inferred that these targets are reasonable. As the result of this research, an energy-efficient (power consumption reduced to 1/3 to 1/5) practical rapid sintering system is constructed. Basic data are collected relative to the tribology of the functionally inclined material, and it is proved that it is feasible to use the material for engine members. The process technology, assessment technology, and devices developed under this project are the first in the world, and are highly evaluated. (NEDO)

  20. Report on the material committee in fiscal 1988; 1989 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    This paper describes a report on the material committee for coal gasification technology development in fiscal 1988. The in-plant test on new materials has performed information investigation on use characteristics and use records of new materials. A sulfurizing corrosion resistance test showed that the aluminum-chromium diffused and permeated material and the molten aluminum plated material stabilize the coated surface and have high corrosion resistance. Ceramics painted lining material was evaluated unusable in a steam diffusion test. Phenol resin was found sufficiently usable as a result of giving the stress test at 100 to 150 degrees C. In developing a let-down valve, a high-velocity water slurry injection test revealed that CVD coating of Ti (C, N) has high effect of suppressing the erosion damage. In a high-velocity powder injection test, PVD coating of TiN and CVD coating of TiC were found to show good erosion resistance. Tests and researches were performed to evaluate durability of furnace materials for manufacturing gasified hydrogen, and elucidate conditions to cause iron oxide burst. Evaluation on repairing techniques, and improvement on durability were also executed. (NEDO)

  1. Report for fiscal 1993 by coal gasification committee; 1993 nendo sekitan gas ka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This report is a compilation mainly of distributed material. In the development of entrained bed coal gasification power generation, gasification is tested in a 2t/d-capable facility and gasification efficiency and operation characteristics are grasped, these constituting the studies of elements to assist pilot plant operation etc. The fluid temperature point of slag is found to decrease by 200 degrees C at the maximum upon addition of flux (CaO), and this improves on slag fluidity. For the development of a demonstration gas turbine, an experimentally built combustor is tested using a real gas. A combined cycle power system is studied by simulation. In the study of pilot plant operation, measures relative to slagging are implemented, inspection and maintenance are conducted for each facility, and the combustor for a demonstration plant is subjected to oil and coal combustion tests. In the study of a pilot plant for developing technologies for hydrogen production using coal, the plant stably runs more than 1,000 hours under 100% load at in a RUN-8-3 operation. Some deposit collects in the neighborhood of the contracted area of the blow nozzle and on some part in the slip stream, but it does not affect operation. No abnormalities are detected in the cyclone or heat recovery boiler. The pilot plant is let to continue its operation, and excellent results are achieved, which are beyond the targets of carbon conversion efficiency of 98% or higher and gas cooling efficiency of 78% or higher. (NEDO)

  2. Fiscal 1991 report on the brown coal liquefaction section meeting; 1991 nendo kattan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    At the 1st through 5th brown coal liquefaction group meetings held for the fiscal year, reports are delivered and discussions are made about the progress of research and development. At the 1st meeting, a fiscal 1991 brown coal liquefaction research plan is introduced, and discussed. At the 2nd meeting, an interim report on the brown coal liquefaction technology development project is discussed. At the 3rd meeting (a joint meeting of the brown coal and bituminous coal liquefaction groups), an agendum entitled 'what the development of brown/bituminous coal liquefaction technologies for the 21st century should be' is reported, and discussed. At the 4th meeting, reports are made on the results of deliberation at the Industrial Technology Council, progress of the follow-up study, progress of the collection of achievements, and so forth. At the 5th meeting, the outline of the follow-up study, the collection of achievements in the pilot plant study (a project report preparation schedule and materials evaluation), the progress of pilot plant dismantling work, etc., are reported and discussed. (NEDO)

  3. Achievement report for fiscal 1997 on developing practical application technology for photovoltaic power generation systems under the New Sunshine Project. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, and development of technologies to manufacture new type amorphous solar cells; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, shingata amorphous taiyo denchi no seizo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Development will be made on high-performance a-solar cells as part of developing practical application technology for a-solar cells for electric power use. Development will be also made on a low-cost process technology. This paper describes the achievements attained during fiscal 1997. Quality improvement has been realized by using a high RF power hydrogen dilution process on a-Si films for front cells of lamination type cells. Four times faster film forming speed was obtained even by using the VHF plasma CVD process, with film quality equivalent to those made by using the conventional RF process maintained. By optimizing the light enclosing construction, the short circuit current was enhanced by over 20%. Discussions were given on forming homogenous a-Si films by optimizing the conditions for forming films on large-area substrates, which resulted in forming film of 30 cm times 40 cm size with good homogeneity at a film forming speed three times faster than the conventional speed. A surface electrode was formed successfully with good uniformity on a substrate with a size of 60 cm times 90 cm. Productivity greater by over three times the conventional productivity was achieved in patterning of transparent electrodes by using high-output laser. Simultaneous and collective patterning and very small and long size collective patterning were realized in a-Si film selection patterning by using the plasma CVD process. (NEDO)

  4. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for development of extra-high efficiency solar cells (fundamental research on extra-high efficiency III-V compound semiconductor tandem solar cells); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (chokokoritsu III-V zoku kagobutsu taiyo denchi gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Sekikawa, T; Kawanami, H; Sakata, I; Nagai, K; Matsumoto, K; Miki, K [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for development of extra-high efficiency III-V compound semiconductor tandem solar cells. Heteroepitaxial structures of compound semiconductors, such as GaAs, on silicon substrates are analyzed and evaluated by EXAFS, Raman and RHEED for the initial stage of the film growth and heterointerfaces. The device capable of in-situ observation of the growing surface structures during the period of heteroepitaxial film growth is introduced, to investigate the effects of rise-up and initial growth conditions on defects. The effects of atomic hydrogen on growth of a GaAs film on a silicon substrate are investigated from photoluminescence and solar cell characteristics, to confirm the effects of reducing defects. Heteroepitaxial growth of InGaP, which has the optimum band width for forming multi-junction silicon solar cells, on a silicon substrate is investigated, to find that an interfacial buffer layer is necessary to form a good film. 2 figs.

  5. Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

  6. Leading research and study report for fiscal 1998. Report on leading research and study on intelligent fiber; 1998 nendo sendo chosa kenkyu hokokusho. Inteligent fiber sendo chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches were conducted with a view to organizing projects for developing intelligent fibers, equipped with environmental friendliness and amenity without being deprived of their original properties as structural and clothing materials, the ultimate goal of the effort being the creation of harbingers of next-generation fibers which would contribute to the advance of industries related to environments, medicine and welfare, and information. What were learned from fiscal 1998 researches are mentioned below. The strength that the general-purpose fibers currently in use exhibit is so small as to be but several percent of what is theoretically predicted for them. Demand will increase a great deal if the actual strength is doubled, for which new technologies have to be developed including those involving super-fiber texture control. For providing the fiber with such functions as environment-friendliness, amenity, etc., it is necessary to develop phasal structure control technologies with regard to fiber morphology, surface texture, etc. For success in practical application in the future of such super-fiber materials, each specimen needs to be manufactured in the order of kilogram by way of trial. Moreover, fiber evaluation techniques have to be developed in the three domains of software, hardware, and interface. (NEDO)

  7. Fiscal 1998 research report. Research on the possibility of promoting CDM project through technology transfer with plant exports; 1998 nendo chosa hokokusho. Plant yushutsugata gijutsu iten wo tsujita CDM project suishin kanosei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on promotion of CDM (clean development mechanism) project through technology transfer with plant exports. Although CDM system was provided in COP3 on climate change held in Kyoto in 1997, its detailed rules including project approval are yet undecided, and only the schedule to provide the detailed rules until COP6 in 2000 was decided in COP4 in 1998. The common recognition that the CDM project with plant exports produces various merits for both Japan and the partner country is increasing. However, from the viewpoint of forming concrete CDM projects, most Japanese enterprises are passive in approach to the CDM project because of no detailed design of CDM, uncertain profitability and procedures, and avoidance of additional burdens. Plant export is also difficult because of the fact that assessment of a new project is difficult. Enterprises' deeper recognition on the CDM project, and a governmental integrated support system are desirable. (NEDO)

  8. Research report of fiscal 1997. Study on total energy and material control (feasibility study on circulating society); 1997 nendo chosa hokokusho. Total energy and material control ni kansuru chosa (junkangata shakai kochiku kanosei chosa) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to construct real sustainable global environment and human society in the 21st century called the century of environment, not only the innovation of manufacturing processes technically supporting such the construction but also the conception including the innovation of the whole society from a wide viewpoint are essential. As a total energy and material control system (TEMCOS) concept, the view of an energy-saving circulating society is attempted which minimizes a total energy and material flow in Japan, and the role and issue of manufacturing industry, in particular, material industry are extracted. As one of the targets of such a concept, the conception of an eco-town is also described. Paying attention on some important material industries including a mass material flow and consuming a large amount of energy such as metal, plastics and automobile industries, the study result on a material flow for every industry is arranged, and some effective issues contributing to minimize a material flow and control energy consumption and CO2 emission are extracted. 80 refs., 67 figs., 30 tabs.

  9. Report for fiscal 1980 on comprehensive survey for nationwide geothermal resources. Survey on Curie point method (Associated material - operation flight report); 1980 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Curie tenho chosa (futai shiryo sagyo shinchoku hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-10-01

    With an objective to identify the status of distribution of deep underground thermal structure, aerial magnetism investigations were executed in the south Kyushu area, and data used in the Curie point method were collected. This paper summarizes the progresses and achievements of the work during the investigation. The report for April 1981 summarized preparation of equipment and materials by EG and G Geometrics Corporation, and the work schedules with the Idemitsu Geothermal Development, Petroleum Resources Development, and Naka-Nippon Airways. The report for April 22 compiled the site preparation and the test flight. The report for April 28 compiled the calibration and magnetism compensation flight. The report for May 5 compiled the implementation of the second flight , and the result of survey for 292 km in total. The report for May 10 compiled the implementation of the third to fifth flights, and the results of measurements for 584 km, 519 km and 360 km, respectively. The report for May 18 compiled the implementation of the sixth to eighth (final) flights, and the results of measurements for 513 km, 584 km and 68 km, respectively. (NEDO)

  10. FY 1992 report on the survey of geothermal development promotion. Electromagnetic exploration (TDEM method) (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Denji tansa (TDEM ho) hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    For the purpose of elucidating a possibility of existence of geothermal reservoirs in the Haneyama area, Oita Prefecture, Electromagnetic survey by the TDEM method was conducted. The survey was made for the area of 80km{sup 2} at 105 measuring points in the south of the Haneyama area, and the resistivity structure reaching the depth of 4,000m from the earth surface was made clear. The resistivity structure in this area is composed of 4 layers: upper medium resistivity layer, central medium resistivity layer, central low resistivity layer and lower high resistivity layer. The resistivity structure discontinuous line ranges between the uplift zone of basement and the sedimentation zone, and the greater part of the alteration zone is distributed and arranged concomitant with the position and direction of the line. As the region with high potential of geothermal existence, cited were the low resistivity zone distributed in the west of the resistivity structure discontinuous line that continues from Mt. Fukuman to the south, the low resistivity zone distributed in the north of the resistivity structure discontinuous line from Noya to the west, and the low resistivity zone distributed in the north of Hosenji and lying between resistivity structure discontinuous lines. (NEDO)

  11. Report of the results of the fiscal 1997 survey. R and D of high efficiency clean energy vehicles; 1997 nendo chosa hokokusho. Kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing an automobile which keeps low pollution using petroleum substituting clean energy, decreases the running energy consumption to a half at least, and reduces the CO2 emission to less than a half of the conventional one at the same time, the R and D started in fiscal 1997. As to the study of a high efficiency hybrid power system, conducted were the prediction of fuel consumption performance of the system proposed, evaluation of element technology using hybrid simulator, evaluation experiment on a new hybrid vehicle, and grasp of overseas trends. In relation to the development of hybrid vehicles, the following were studied: methanol fuel cell loading hybrid vehicle, CNG engine loading hybrid vehicle, CNG ceramic engine loading hybrid truck, CNG lean burn engine loading hybrid truck, LNG engine loading hybrid bus, and DME engine loading hybrid bus. Besides, a survey on synthetic fuel and the related survey were carried out. 17 refs., 185 figs., 101 tabs.

  12. Leading research report for fiscal 1998 on the report on researches on intelligent social infrastructure technology; 1998 nendo chiteki shakai kiban kogaku gijutsu no chosa kenkyu hokokusho sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches are conducted for showing some guidelines on the system and method of the intelligent social infrastructure technology (ISIT) as a 21st century type systematization technology, and a report is submitted on the result. Discussed in the report are the technological system and image of ISIT, the research and development setup and administrative tasks involving intelligent social infrastructure construction, and the systematization and operation of the ISIT. Mentioned as important element technologies are the infrastructure and information/communications technologies for security and disaster prevention, information technology and automatization technology for maintenance, and intelligent materials enabling disaster prediction and detection. Stated in connection with the future development of ISIT are information/communication technologies for system control, monitoring, and normal/urgent dual use. Specific examples are shown, such as the active card, urban disaster prevention and monitoring system, active city, intelligent network, and so forth. (NEDO)

  13. FY 1997 report of survey on the intellectual property in international collaboration research project; 1997 nendo chosa hokokusho (kokusai kyodo kenkyu ni okeru chiteki zaisanken ni tsuite no chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In promoting international collaboration research project, coordination of the patent system of each country which participants to the project belong to has broad implications in concluding the contract for the project. For example, in Japan, 100% of the patent belongs to the government for contrast or collaboration project with the government. While, in the USA, the patent developed by the private company belongs to the private company even for the contrast project. In Japan, the shared patent can not be transferred to the third party or implemented without agreement with the partner. While, in the USA, the shared patent can be transferred to the third party or implemented without agreement with the partner. Due to such a difference, some projects can not be established by ill coordination of intellectual property even when the meaning of the projects is well understood. In this survey, was investigated the outline of patent systems of major countries to study about what should well balanced treatment of intellectual property in international collaboration research project be in the future. 4 figs., 8 tabs.

  14. Fiscal 1997 survey report on the trend of global warming protection measures of substituting freons; 1997 nendo chosa hokokusho (daitai freon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The trend survey was conducted of global warming protection measures by participation in international conferences, scientific society meetings and lecture meetings, and by literature surveys. We participated in the international conference on ozonosphere protection measures. In the 9th meeting of the nations which concluded the Montreal Protocol, the strengthening of restrictions on methyl bromide was decided on. In the UNEP solvent technology selection conference and the OORG conference of the World Bank, reports were made on substituting solvents in Japan, activities supporting developing countries, and the developmental trend of urethane use foaming agent. In the international conference on ozonosphere protection measures, introduced were the present status of Japan`s ODA for developing countries and examples of success of the substitution in the solvent field. The paper included nine reports on CFC destruction technology related literature made public in the past one year. The paper also introduced a comparative study of de-HCFC substituting technology at U.S. Oak Ridge National Laboratory, U.S. EPA`s prediction of emission of fluorine 3 gas, the predicted value of HFC emission and trial calculation of contributing rate in all greenhouse gases by IIR, Green Peace and Elf Atochem, and NOAA`s measured data on SF6 in the atmosphere. 49 refs., 46 figs., 26 tabs.

  15. FY 1992 report on the survey of geothermal development promotion. Geochemical survey (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Chikagaku chosa hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    For the purpose of studying an expanse and characteristics of the geothermal system and a possibility of geothermal development in the Haneyama area, Oita Prefecture, geochemical survey was conducted. In the survey, various kinds of analyses were made for 13 specimens of hot spring water and 5 specimens of surface water in the area of about 280km{sup 2} at 402 measuring points of the concentration of Hg in soil gas. The results of the survey were as follows: In this survey area, it was thought that the HCO{sub 3} type geothermal water of a comparatively low temperature which was heated by the wide-spread conduction heat from the depths was widely distributed deeper than the depth of 500-700m, and it was presumed that a possibility was low of existence of a high geothermal potential which can be used for the geothermal power generation in the part deeper than the drilling depth of 700m. In the Noya area in the southwest part of the survey area, the high temperature deep geothermal reservoir was confirmed. In this area, the high temperature neutral-alkalescent Cl-SO{sub 4} type geothermal water was distributed in the depth of several 100 meters or deeper. The geothermal water seemed to flow from NE to SW along the structure in the NE-SW direction, and it was concluded that the area was the most promising one. (NEDO)

  16. Fiscal 1998 research report on information structuring technology for advanced use of NEDO research reports; 1998 nendo NEDO seika hokokusho nado no kodo riyo ni hitsuyona joho kozoka gijutsu no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was made on electronic NEDO research reports corresponding to the recent extending trend of Internet. The logical structure and electronic format of NEDO research reports as document were first studied considering document disclosure and reuse of technical information. HTML as electronic format for Internet is unfortunately insufficient to describe the logical structure of NEDO research reports because of HTML's restricted description. Thus, XML which is being watched because of its possible definition of original tags was studied in place of HTML. As a result, because at present preparation of standards on XML and a compatibility for implementation of standards are insufficient, it was concluded that construction of the electronic document system for NEDO research reports is still too early. However, since adoption of XML as document format is important from the viewpoint of a property succession on Internet, preparation of the XML format file of NEDO research reports is essential. (NEDO)

  17. Fiscal 2000 achievement report on the research and development of transfer standard gage for oil flowmeter (final assessment); 2000 nendo sekiyu ryuryokei no iten hyojunki no kenkyu kaihatsu seika hokokusho (saishu hyoka hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In a servo PD (positive displacement) flowmeter for oil, a differential pressure transmitter detects difference in pressure between the PD flowmeter input and output ports and a rotor is driven by a servo motor so that the pressure difference between before and after the PD flowmeter rotor will be zero. The design enables high-accuracy measurement across a wide range of flow rates and is not easily affected by the surrounding physical conditions such as viscosity and density. For the development of such a flowmeter, it is necessary to develop a rotor that rotates smoothly free of locking in a steady and uniform flow, to build a visualized model that enables the analysis of flow inside the flowmeter which in turn will enable the determination of optimum differential pressure detecting ports, and to connect a newly developed servo mechanism to the thus determined ports. As the result of the research, a servo PD flowmeter is developed, which is a 50mm diameter prototype employing the Invoflex tooth form which is the waveform for a rotor suitable for a high performance flowmeter. Placed in a generally used oil flow calibration liquid, which is gasoline, kerosene, or the like, it covers a flow rate range of 1:10 and reads with an accuracy of {+-}0.1%. It remains stable in performance and suffers but a little change with the passage of time. (NEDO)

  18. FY 2000 report on the survey of technological strategy for the creation of the robot society in the 21st century; 2000 nendo chosa hokokusho. 21 seiki ni okeru robot shakai sozo no tameno gijutsu senryaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    For the purpose of constructing the future-oriented robot technology system and clarifying the robot technology strategy viewed from the necessity, contribution and marketability in the society, investigational study was made by the special committee for technology strategy survey. In the section meeting for the needs, the following 5 working groups had a grasp of the needs: reinforcement of production technology; bio-industry; medical act support; how to cope with disasters; life support. Based on the results of the analysis of factors of the successful manufacture of industrial robots during the 1980s - 1990s, the quantitative estimate of the market was made as much as possible. Further, in the section meeting for the seeds, the 6 working groups were set up, and they conducted the trend survey/analysis of the development of element technology of robot in Japan and abroad, the extraction of developmental subjects, etc. As a result, the following were specified as the seeds to be emphasized: construction of the remotely distributed system using network; nano-handling technology; sensitivity interface/human behavior comprehension technology/simulation technology, robot vision, moving technology, advanced manipulation technology. (NEDO)

  19. FY 1992 report on the survey of geothermal development promotion. Gravity prospecting (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Juryoku tansa hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    For the contribution to elucidation of the geothermal structure in the Haneyama area in Oita Prefecture, gravity prospecting was conducted. Survey was carried out in the area of about 280km{sup 2} at 205 measuring points, and analysis was made altogether with the existing 3,273 gravity measuring points. As a result, the following were made clear. The gravity basement forms the fault-state structure that sinks several 100 meters to the south side on the line from the south edge of the Higashi-shiiya ridge to Mt. Kurotake - Mt. Daigansen - Amagase hot spring in the SW direction. This fault was made correspondent to the Beppu north fault on the east side of Mt. Kurodake. Each of the following regions is the region where the fault-state structure that predicts the development of fracture and the area of distribution of alteration zone that can be cap rock overlap each other: NW edge of Shishimuta sedimentation zone - Machida alteration zone distribution area; N edge of the Shishimuta sedimentation zone - Ibushi alteration zone/Noya alteration zone distribution area; Vicinity of Mt. Kurodake - Hijiu alteration zone distribution area. It seems that the above-mentioned regions have high potentiality of geothermal exploration. The region where new igneous activities are seen, which is near the heat source, is important for exploration. The distribution area is seen near the west of the Mizuwake Pass ridge. (NEDO)

  20. FY 1994 report on the survey of geothermal development promotion. Complementary survey on the fracture system, etc. (Wasabizawa area); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho futai shiryo. Wasabizawa chiiki danretsu kei tou hokan chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    For the contribution to elucidation of the geothermal structure in the Wasabizawa area, Akita Prefecture, survey by the paleomagnetic measurement and fracture system measurement was conducted of the borehole cores and specimens of outcrop granite obtained from boreholes of N6-WZ-3 and N6-WZ-4. In the survey, the following were carried out: measurement of the core fracture system of N6-WZ-3 (102-1,505m) and N6-WZ-4 (507-1,556m), paleomagnetic measurement of 9 outcrop granite specimens and 16 core specimens, and k/Ar age determination of 3 outcrop granite specimens. As a result of the paleomagnetic measurement of outcrop granite, the magnetization azimuth of the schistose granodiorite distributed in Kuwanosawa was regarded as almost NS. The measured magnetization azimuth of the core specimen obtained from the same rock mass was also made NS-based, and measurement of the fracture in the neighborhood was made. As a result, it was found out that the NNW system was dominant in dikes and that there was the NE system in most of the small geothermal channels. The fracture system of well tended to develop around the boundary between granite and metamorphic rock, and it was thought that this part could be a reservoir if temperature conditions are prepared. (NEDO)

  1. FY 1974 report. Study on hydrogen combustion technology; 1974 nendo suiso nensho gijutsu ni kansuru kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    In the use of hydrogen as fuel, there is the problem on NOx emission. The amount of NOx emission is not as much as in the use of coal or oil, but is more than in the use of natural gas or town gas. However, it can be said that hydrogen is an ideal fuel if considered that it does not emit other air pollutants such as CO, HC and soot/dust which are usually associated with hydrocarbon base gas fuels, and also that hydrogen forms a circulation system which is ecologically sound. The flame of hydrogen is non-luminous, but the flame temperature is high. The formation of NOx depends strongly upon the flame temperature, and therefore, in the design of hydrogen burner, it is necessary to well mix it with air and to avoid the production of the local high temperature region. Further, when using hydrogen to large boiler, the combustion technology to control NOx reduction is needed. About the hydrogen flame, the matter to be noticed is an experimental result that NOx reduction was observed by adding trace ammonia to hydrogen gas. If this method can be successful, NOx can be reduced with no increase in fuel consumption. It leads to hydrogen's reaching a position of clean energy. (NEDO)

  2. Fiscal 1998 report on Japan-Asia international cooperation project; 1998 nendo Nichi Asia kokusai kyodo kenkyu jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the development of talent, industrial infrastructures, and new industries in countries that received Japanese cooperation, Japanese researchers were sent to universities and research organizations in Asian countries, where they were engaged in joint research and development, which involved (1) micro device technology, (2) technology for manufacturing industrial silica material by chaff incineration, (3) technology for forming and machining of alloys difficult to machine, light in weight, and high in strength, (4) technology for rare metal isolation and refining, (5) cascade-wise utilization and practical application of biomass in Asia, (6) exploration and utilization of microbial resources in Tropical Asia, (7) evaluation of biological resources existing in Southeast Asia and construction of information network, (8) development and evaluation of cultured articular cartilage, (9) technology for utilizing wastewater for production of valuable substances, and (10) studies for utilizing biological resources through utilization of diversity of symbiotic microbes and their adaptability to surroundings. Under item (1), it was planned that ultrasonic micro transducers and micro fluid devices be developed for use in the medical field. (NEDO)

  3. Report on establishment of new energy vision in Akeno Village (Yamanashi Prefecture); Akenomura shin energy vision sakutei hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established to move positively forward the introduction of reproducible new energies and promotion of energy conservation at the district level, based on the basic conception of 'protecting and nurturing nature and culture of Akeno Village to leave them to the future generations'. The activity achievements were put into order by the following five items: 1) basic conception and basic policy in establishing the new energy vision, 2) the general situation of Akeno Village, 3) investigation on energy demand and supply in Akeno Village, 4) estimation of existence quantity of new energies, and 5) the new energy introduction vision. Item 5 is composed of the conception in establishing the idea, new energy introduction plans, and new energy introduction projects. The new energy introduction projects include introduction of photovoltaic power generation into Akeno Middle School, installation of wind power generation facilities at open space in the 'Road Station', introduction of hybrid street lights using micro wind mills and solar cells into the school zone roads, and introduction of clean energy fueled automobiles into official use automobiles. (NEDO)

  4. Report for fiscal 2000 on feasibility study for commercializing new energies; 2000 nendo shin energy jigyoka feasibility study hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    Tobu Town in Nagano Prefecture has established a 'Tobu Town new energy vision' and set up a polity to make efforts in discussing new energy introduction into public facilities which will be constructed in the future. Discussions were given on commercialization possibilities of the energy center system, particularly energy supply by cogeneration utilizing natural gas, for the four facilities in the 'Forest of Welfare'. Comparison was performed on primary energy consumption, CO2 emission reducing quantity, and economic performance between the existing energy supply systems and the energy center system. Discussions were also given on means to utilize solar energy. The plan calls for establishing the energy center in the 'Forest of Welfare', wherein facilities composed mainly of a gas engine type cogeneration plant (500 kW) and a solar heat collector (36.4 m{sup 2}) will be installed to supply the object facilities with electric power and hot water. This operation will be able to reduce the primary energy consumption by 12% and CO2 emission by 18%. (NEDO)

  5. Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-10-01

    Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

  6. Report on bio-energy survey project in Sumoto City; 2001 nendo Sumoto baio energy chosa jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    With an intention to solve environmental problems and energy problems simultaneously in Sumoto City, Hyogo prefecture, surveys have been performed on feasibility of introducing biomass energy in the district. The dairy farming in Sumoto City has a trend of increase in the number of livestocks being fed in individual farms, and increase of milking quantity per livestock (increase of sewage discharge amount), with the increase of excessive excreta amount causing a problem. The Sumoto Dairy Farming Association is experiencing generation of excreta of 156 tons a day, which requires manure handling and disposal of 112 tons a day even after deducting the field dispersion. Discussions on a biogas plant with a capacity of 100 tons a day call for biogas generation amount of 2,500 m{sup 3} a day, electric power generation amount of 4,500 kWh a day, fuel cell size of 100 kW x 2 units, and heat generation amount of 6,000 kWh a day. A total of the estimated project cost amounts to 2,450,000,000 yen, the annual running cost to 65,280,000 yen, and the annual income to 82,000,000 yen. The electric power generation cost is 135 yen per kWh, the heat production cost is 952 yen per liter (converted to kerosene), and the saving amount due to excessive electric power and heat utilization amounted to 10,700,000 yen. The annual amount of CO2 reduction is 1330 tons. (NEDO)

  7. Achievement report for fiscal 1998. Home rehabilitation system for aphasia patients; 1998 nendo seika hokokusho. Shitsugosho zaitaku rehabilitation shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Development has been made on the element technologies for a home rehabilitation system for aphasia patients. First, studies were performed on an authoring procedure for aphasia patient training, and partial trial production and development were carried out on an authoring system for the training program formula. Then, studies were executed on a training simulation and analysis filter, and partial trial production and development were implemented on a home rehabilitation supporting and self-teaching system. Next, an input and output mechanism for voice signal processing was studied, and aphasia patient and caregiver human interface was partially fabricated on a trial basis. In addition, a remote rehabilitation communicating method was researched, and partial trial production was carried out on a remote rehabilitation evaluation and diagnosis support means. Finally, communication assisting means were researched, and a communication assisting system was partially produced on a trial basis. Good evaluation results were given on a demonstration system. Although partial indications were given on minute parts, practical agreement was obtained as a whole. Great expectation was given particularly on the remote rehabilitation system and the authoring system. (NEDO)

  8. Report on investigation in fiscal 2000 of industrial technology information; 2000 nendo sangyo gijutsu joho chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Pursuing the measures for how the national research institutions in Japan who have been made into independent administrative corporations should be positioned in maintaining and developing the industrial strength, investigations were performed with the points focused on measures taken in the United States to improve research environment, and the ways the national research institutions should be. The investigation results were summarized on the following four areas: 1) transition of research and development policies, 2) on the national research organizations, 3) structuring of database for researchers in universities and national research organizations, and 4) future challenges and suggestions. Item 1) has put the subject into order of the history of establishing legislations related to the U.S. technological policies, measures to promote research and development, budgetary management, grants, and preferential treatment. In Item 2), visits and investigations were executed on government-owned, government-operated laboratories and government-owned, contractor-operated laboratories whose operation patterns are different with each other. The results were put into order of institutions, roles, personnel systems, activation measures, joint research institutions, and finance. In Item 3), a data list was prepared on researchers relative to advanced technology programs contributing greatly to enhancing the competitive edge of U.S. corporations. (NEDO)

  9. Summary of achievement reports on the Sunshine Project in fiscal 1978 (Hydrogen energy); 1978 nendo seika hokokusho gaiyoshu. Suiso energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-04-01

    This paper summarizes achievement reports on the Sunshine Project in fiscal 1978 (hydrogen energy). In hydrogen manufacturing methods, studies are described on materials of membranes and electrodes used in high temperature and pressure electrolysis. In thermo-chemical method, studies are continuing on cycles of the iron system, iodine system, and mixed system (composed by thermal, photo and electro-chemistries). For the iodine system, summary design was performed on an experimental device. For the mixed system, trial fabrication and experiments were carried out on a beam radiation type electrolytic tank that electrolyses quickly HI and Fe{sup 3+} produced in the photo-chemical reaction, and separates the products. Discussions were also given on HI decomposition (hydrogen acquisition) by means of heat diffusion. With respect to storage and transportation, development is being made on optimal metal hydrides. In combustion technologies, discussions are given on combustors and catalysts to break through the dilemma of high NOx emission and frequent occurrence of reverse ignition. For fuel cells, the paper describes developments of the materials thereof, high-temperature solid electrolyte type fuel cells and alkaline aqueous solution electrolyte type fuel cells. Regarding the non-steady hydrogen engines, the paper describes fundamental studies on non-steady jet flow behavior using shock tubes, and single cylinder engine tests. It also describes hydrogen safety assuring measures, and studies on energy systems. (NEDO)

  10. New energy visions for City of Sapporo. Report on the survey results; Sapporoshi shin energy vision chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    This project is aimed at survey/study on new energy reserves and possibility of their introduction for City of Sapporo, and, at the same time, drawing the future visions for introduction of new energies to reshape the city. The new energies considered are solar energy and waste heat carried by sewage, in addition to waste heat from garbage incineration and garbage-derived solid fuels, which are now already utilized as the heat sources for district heat supply. The city as a whole consumed energy of 28,100Tcal/y in 1985 and 45,700Tcal/y in 1996, and emitted carbon dioxide totaling 2,690,000 and 3,510,000 tC/y in the respective year. The projects considered for introduction of new energies include construction of a new cleaning plant and heat supply system at the southern gate of Sapporo Station, introduction of clean energy automobiles, increasing attractiveness of Satoland project, utilization of low-temperature heat at glass pyramids in Moere Park, promotion of photovoltaic power generation, construction of facilities for culture-exchanging, and construction of an environmental plaza. (NEDO)

  11. Report on new energy vision establishment in Oga City area; Ogashi chiiki shin energy vision sakutei hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established in Oga City in Akita Prefecture. The population of the city is continuing the decreasing trend since 1955 to 30,462 persons as of 2000. The number of employed people by industry is in the trend of decreasing in the primary industry, leveling off in the second industry, and increasing in the tertiary industry. The annual energy demand in this city is 838,000 MWh in electric power and 302 times 10{sup 13} J, accounted for by the consumer department at about 44.4%, the transportation department at about 28.3% and the industrial department at 27.3%. The carbon dioxide emission amount therefrom is estimated 68,100 t-C. The expected usable quantity of new energies in the city would be available in solar heat as the largest source, followed by solar beam and wind power, whose amount is estimated 136.41 times 10{sup 13}J annually in total. The new energy introducing project includes introduction of wind power generation into Namahage Line and its vicinity and the Ikari area, manufacture of fuel from refuses, introduction of clean energy fueled automobiles into the cars used by the city office, introduction of photovoltaic into the general gymnasium and primary and middle schools, and solar heat utilization at the general gymnasium. (NEDO)

  12. Research report of fiscal 1997. Feasibility research on domestic wind farms; 1997 nendo chosa hokokusho. Kokunai wind farm kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research was made on large-scale wind power generation projects under planning or construction. Issues of the following 5 areas were arranged considering topographic, geographic and meteorological conditions, and the type of municipal corporations: Tomamae town, Hokkaido, Tachikawa town, Yamagata prefecture (third-sector), Hisai city, Mie prefecture, Otoyo town, Kochi prefecture, and Kishuku town, Nagasaki prefecture (third-sector). These projects are supported by MITI`s local new energy introduction promotion project subsidy started in fiscal 1997 covering a half of construction cost (within 200 million yen/year). Requirements for this subsidy are that an applicant is either a municipal corporation or a third-sector, and that a total generating capacity is not less than 1200kW. Another subsidy system covering 1/3 of construction cost and a debt guarantee system are prepared for large-scale private projects not less than 800kW. Hearing was made on some private projects in Esashi town, Akita city and Hasaki town. Technical requirements, specifications, guideline and some examples for system interconnection are also summarized. 10 figs., 24 tabs.

  13. Report on the environmental safety evaluation sub-committee in fiscal 1992; 1992 nendo kankyo anzensei hyoka bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the environmental safety evaluation sub-committee for the coal liquefaction plant in fiscal 1992. The sub-committee, upon having received reports on the result of environmental safety evaluation tests performed in fiscals 1991 and 1992 by NEDO, deliberated and discussed carefully the contents thereof. In order to ensure labor hygiene for coal liquefaction plant workers, health influence on liquefied oil users, and social acceptability of the liquefied oil, NEDO has performed the comprehensive brown coal pilot plant operation and oil safety tests. The tests are in accordance with the labor safety and hygiene law, the chemicals examination law, and the MPD issued by OECD, and performed on each fraction produced in the pilot plant and the whole fraction mixing the former fractions, using rats, rabbits, and guinea pigs. The test items included: acute inhalation toxicity and oral repeated administration (using rats); eye stimulation, repeated coating and skin stimulation (using rabbits); photo-toxicity (using guinea pigs); mutagenicity tests (microorganisms, bacteria and chromosome anomaly); resolution tests; fish toxicity; concentration degrees; algae growth obstruction; and water flea breeding obstruction. As the result, the toxicity was found light. (NEDO)

  14. Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1980 reported. This year, a detailed conceptual design was carried out on a coal fired MHD generation system, with points for the technological development concretely examined. In addition, investigation was conducted on the progress of MHD generation technology, development situation of other generation systems, state of energy resources, etc., in various foreign countries. In the conceptual design of the coal fired MHD generation plant, the system structure of a 2,000 MWt class commercial MHD generation plant was explained, as were the conceptual design of the structural elements and proposals for a 500 MWt class demonstration plant and an 100 MWt class experimental plant, for example. In the overseas trend of R and D on MHD generation, investigations were made concerning the U.S., Soviet Union, and China, with details compiled for such items as generation plants, combustors, generation channels, heat resisting materials, superconducting magnets, heat exchangers, seed slags, inverters, boilers and environments, and commercial plants. (NEDO)

  15. Report on a survey in fiscal 1999. Survey on research exchange possibility; 1999 nendo kenkyu koryu kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey deals with research institutions of governmental organizations, universities, and business entities for the purpose of discussing the possibility of research exchange standing on a long-term point of view to serve for solving global environment problems, and the way the exchange should be. The research exchange shall cover the areas of trends in research and development of global environment related technologies, themes for the research and development, institutions for the research and development, and exchange of researchers and information with these research organizations. In fiscal 1999, three survey missions were dispatched to cover the following three areas: (1) surveys on research possibility of catalyst development by means of combinatorial chemistry, (2) surveys on research exchange possibility for thermo-chemical solar hybrid fuel production technologies, and (3) surveys on research exchange possibility for structuring function improving technologies of the 21st century type. Each survey mission has visited research institutions of the world to survey the trends in researches related to global environment, and the possibility of exchanging researches with RITE. The visits presented the following conclusions and findings: (1) the research on the combinatorial chemistry in the U.S.A. is still in the initial stage; (2) important findings were obtained when surveys were made on methane reformation utilizing solar heat, and coal gasification technologies in Europe; and (3) surveys were made on pioneering researches on plant molecule physiology in Europe. (NEDO)

  16. Fiscal 2000 achievement report. Welfare technosystem research and development (Ube); 2000 nendo walfare technosystem kenkyu kaihatsu (Ube) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts continue to develop welfare nursing equipment for helping persons in need of nursing care or handicapped persons who live an independent life. Efforts are exerted in three fields for developing (1) a motor driven wheelchair in which the occupant feels as if driving a car, (2) an online cardiac function monitoring system using a cardiac sound sensor, (3) an automatic pressure belt for patients of postural low blood pressure, (4) and a seated position aiding and stabilizing device for workers with legs not fully useful. In field (1), the steering wheel, brake, and driving system are contrived so that the occupant may easily drive the wheelchair as if in an automobile driver's seat. In field (2), a device is developed to monitor and examine the heart rate and respiration rate, for which a cardiac sensor has to be installed on the water bed or an air mattress. In field (3), a computer controlled automatic pressure belt is developed for patients of myelopathy or cerebrovascular disease. In field (4), a work assisting device is developed to help seated workers with leg troubles. (NEDO)

  17. Report on the brown coal liquefaction sub-committee in fiscal 1992; 1992 nendo kattan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the brown coal liquefaction sub-committee in fiscal 1992. The first sub-committee meeting presented an interim report on the status of progress in complementary researches in fiscal 1992. The report covers the following items: discussions on effects of reaction factors on scale deposition in a preheater and a reactor and the liquefaction oil yield, supplementary experiments to enhance recovery rate of naphtha from under-flow in the de-ashing system and enhance accuracy of expression to estimate the interface precipitation velocity, and discussions on product oil types and catalyst types. The second sub-committee meeting reported fundamental discussions on the primary hydrogenation and hot water treatment of brown coal as an interim report on the achievements, and discussions on de-ashing and catalyst properties, liquefying reaction activity and scaling performance of catalysts. The third meeting reported the support on compiling the achievements by means of collecting complementary data of the pilot plant using PDU. A 7,800-hour life verification test was completed on the fixed bed secondary hydrogenation catalyst. A method was established to recover naphtha from the under-flow in a de-ashing settler. An expression to estimate the interface precipitation velocity was also established. Affirmation was made on the pylite catalyst performance, and reactivity of the category A coal assumed in the demonstration device. (NEDO)

  18. Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

  19. Report on survey/research on energy-related elementary techniques; Energy kanren yoso gijutsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The survey/research project is implemented for establishing environment-compatible energy systems in urban areas by constructing wide-area heat supply networks to exchange energy among cities. This project studies, taking Kanagawa Pref. as the model area, distributions of unutilized energy sources, and possibilities of their utilization for heat supply. There are large quantities of unutilized energy, including waste heat from power plants, general works and cleaning works, and low-temperature waste heat from, e.g., sewage and pumping systems. The district air conditioning promotion areas are selected from those consuming large quantities of heat energy in the prefecture, and their characteristics are grasped. The effects of the networks on total energy consumption of the entire prefecture are estimated for the cases of introducing the district air conditioning systems or wide-area heat supply networks in these selected areas. Introduction of optimum advanced heat utilization systems in stereotyped areas is also considered, in order to predict the effects of introduction of wide-area heat supply networks. (NEDO)

  20. Report of regional new energy vision for Kannami Town; 2001 nendo Kannami cho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For promoting the introduction of new energy and for enhancing people's consciousness of such at Kannami Town, Shizuoka Prefecture, surveys and studies were conducted involving the energy consumption structure of the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The town consumes approximately 5-million GJ/year, with the industrial sector consuming 47%, the transportation sector 29%, and the residential and commercial sector 26%. When a comparison is made, the percentages of the residential/commercial and transportation sectors are relatively higher than the national average. Projects for new energy introduction were studied, which involved photovoltaic power generation for the town office, community hall, primary and junior high schools, nursery schools, and general residences; solar heat utilization for public facilities, greenhouses, and general residences; wind power generation for sightseeing facilities, public gardens, and emergency evaluation areas; utilization of sewage waste heat for the sewage purification center; utilization of hot spa waste heat in the urban area; a biomass-fueled power plant; medium- and mini-scale hydroelectric power generation for the drinking water treatment plant; refuse-fueled power generation at refuse incineration facilities; use of clean-energy automobiles; natural gas-fueled cogeneration for public organizations; and so forth. (NEDO)

  1. New energy vision of the Gushikami Village area; 2001 nendo Gushikami son chiiki shin energy vision sakutei tou jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Gushikami Village, Okinawa Prefecture, an investigational study was conducted of the energy demand of the village, existence amount of new energy, plan for new energy introduction, etc., and a vision was worked out. The energy demand of Gushikami Village was estimated at 640.2 x 10{sup 6} MJ/y. By sector, it consisted of 37.1% in the transportation sector, 32.0% in the commercial/residential sector and 30.8% in the industrial sector. The rate of energy source was 73.7% of petroleum-base fuel and 26.3% of electric power. As the plan for new energy introduction, the following were studied: introduction of photovoltaic power generation to the village office/museum/elementary school/junior high school, introduction of solar heat utilization facilities to the meal providing center/gymnasium, introduction of wind power generation to the sports park, project of wind power generation on the sugar cane hill (600kW x 6 turbines), cogeneration by composting of stockbreeding waste and methane, introduction of clean energy car to official vehicle, introduction of natural gas vehicle, installation of experimental plant for conversion of sugar cane to methanol, etc. (NEDO)

  2. FY 1998 R and D project on industrial science technology; 1998 nendo ryoshi kino soshi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The R and D on quantum functional devices (QFDs) were conducted, and the FY 1998 results were summed up. In the comprehensive survey on QFDs, the following were carried out for the efficient R and D promotion: R and D progress state survey/problem extraction/analytical study, technical trend survey, overseas survey ordered from overseas supplier, common basement technology study, etc. In the R and D on technology for QFDs, integration of multivalued logical devices using tunneling control functional devices, integration of logical memory devices using quantum levels, integration of quantum band combination-type multi-functional devices, silicon insulating film tunnel memory devices, assembly quantum dot functional memory, quantum wave switching functional devices, integration of single electron logical devices, integration of CMOS combination-type single electron devices, etc. Moreover, in the development of the basement technology of single electron devices, technology to construct element devices using quantum functions, basement technology of single electron device integration devices, architecture of single electron device information processing circuit system, etc. (NEDO)

  3. Report on new energy vision at Hinase Town area; 2001 nendo Hinase cho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    With an objective of accelerating introduction of and uplifting consciousness on new energies at Hinase Town in Hyogo Prefecture, investigations and discussions were given on the energy demand, quantity of new energies available, and the new energy introduction projects for the town, thus a new energy vision was established. The estimated amount of energy consumption in Hinase Town is 242,814,320,000 kcal in fiscal 2000. The amount of carbon dioxide discharge associated therewith is 76.57 t-CO2/year. Regarding the energy consumption by departments, the industrial department consumes the most, followed by the transportation department, civil household department, and civil business department. The new energy introduction projects have discussed servicing of the bio-gas plant utilizing organic wastes and cogeneration, the new energy introduction projects for the Natural Energy Island at Kakui Island and the ocean ranch consisted of the use of solar heat water warmer, solar cell powered street lights, photovoltaic power generation, and electric cars for sightseeing visitors, the Eco-school promotion project for primary schools, introduction of energy saving devices into the town office, and the new energy proliferation and enlightenment project. (NEDO)

  4. Report on the FY 1999 basic research on intelligent structure; 1999 nendo kozo chinoka no kiso kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A concept of a system is constructed in which a series of the flow from the construction of structures to the shape and control in structural phase, repair, and dismantlement is made effective and controllable by giving a function of intelligent structure to structural systems in aerospace/architecture/civil engineering fields. For it, fundamental technologies required for the systems were extracted for construction of the technology system. Further, in relation to the intelligent machinery system including the control method, manipulation, and communication of the structure under the micro-gravity environment required for this system, the basic experiment was conducted at the ground gravity-free experimental center to acquire the effective data. As to the base technology, three fields were studied of the intelligent machinery system including the behavior/control of materials and structure, intelligent robot, and communication. In the experiment on micro-gravity environment, experiments were carried out on the behavior of micro-gravity rover for small planetary probe, inter-satellite group communication, capture of trouble-satellite, development of inflatable structure, and hopping robot. The valuable data were obtained. (NEDO)

  5. Fiscal 2000 pioneering research on the spintronic device basic technology; 2000 nendo spintronic soshi kiban gijutsu sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Researchers specializing in technologies of magnetism or semiconductor were drafted from the industrial, official, and academic circles, who conducted hearings, patent investigations, overseas surveys, and the like, concerning spintronics. Collected in this report are the outline of the research and development of spintronic device technology, its current state and tasks and its importance from social and economic viewpoints, and the strategy that Japan should follow in the research and development of the technology. Important spintronic device technologies now attracting attention are mentioned below. The nonvolatile magnetic memory device MRAM (magnetic random access memory) is supposed to be the device which will enjoy practical application first among like devices. It is expected that the spin conduction device will lead to novel functions when the possibilities of the spin-dependent electric conduction phenomenon are further pursued. It is hoped that the spin optical device will be used as a light isolator, light spin logic device, field induced variable wavelength laser device, spin laser device, high-speed light switch, and so forth. It is necessary to watch the development of a spin-aided quantum computer which is still at the stage of basic study. (NEDO)

  6. Fiscal 2000 achievement report. Welfare technosystem research and development (Niihama); 2000 nendo walfare technosystem kenkyu kaihatsu (Niihama) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop welfare equipment systems for helping people needing care lead an independent life. In collecting data on the transfer of patients and carrying out research and development in this connection, activities are conducted to develop (1) a transfer wheelchair and a transfer aiding wheelchair, (2) a simplified transfer type toilet, and (3) a tilt mechanism installable on a standard wheelchair. Under item (1), a wheelchair and an auxiliary wheelchair enabling the transfer of a person who cannot move without help between a wheelchair and an automobile are experimentally built. Under item (2), a simplified transfer type toilet to which a single attendant can easily guide the patient from the bed is developed. Under item (3), a tilt mechanism is developed, installable on a wheelchair to recline the same for the aged person to assume a comfortable attitude. In the development of a portable character reading device, a finger tip reader was experimentally manufactured for reading Japanese characters. (NEDO)

  7. Report on a survey in fiscal 1999. International study exchange project; 1999 nendo kokusai kenkyu koryru jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Exchange with overseas researchers and research organizations has important significance in promoting research and development toward creating new research areas and structuring new technological systems intended for solving global environment problems. In cooperation with RITE and RITE researchers and relevant learned societies, researchers were invited or dispatched to international conferences and international symposiums with regard to global environment related technologies. In addition to interaction with major overseas research institutions and universities, medium and long-term dispatch and invitation have been performed that are considered to play an important role in future research exchange activities based on the achievements of short-term invitations and dispatches and examinations with potential research exchanges. As a result, domestic and overseas interactions on the latest researches were performed, while basic and applied researches related to global environment technologies are being proceeded also in various areas of studies outside the country. It was identified that these exchange activities have close relationship with research and development of industrial technologies serving for global environment preservation, which are being promoted by RITE. (NEDO)

  8. Fiscal 2000 study on technology and marketability concerning phytoremediation; 2000 nendo phytoremediation ni kansuru gijutsu oyobi shijosei no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigative study was conducted on phytoremediation with the purpose of correcting soil contamination caused by heavy metals and the like. In Japan, in connection with the cadmium pollution along the Jintsugawa River region in Toyama Prefecture, a growth of botanical colony such as Athyrium ykoscense was confirmed having a high capacity in absorbing/accumulating heavy metals, with a possibility suggested that they may be utilized for phytoremediation. In a technological research for restoring the environment sustainingly in a wide area, feasibility has been proven to remove polluting agricultural chemicals in farmlands and toxic substance in old industrial sites by making forest trees like poplars, lawns and herbage function. In a project for the cleanup of oil contaminated soil after Gulf War, a demonstrative test of bioremediation for one hectare was performed and, after 15 month experiment, 80 to 90% of aliphatic compounds and 50 to 60% aromatic compounds were degraded. In EU Framework Program in Europe, phytoremediation projects have been implemented across the member countries. (NEDO)

  9. Fiscal 2000 achievement report. Welfare technosystem research and development (Sapporo); 2000 nendo Welfare technosystem kenkyu kaihatsu (Sapporo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Activities are conducted on system technologies for ensuring comfortable living circumstances and thereby helping aged or handicapped people live independently in snowy cold regions. The research and development efforts center about the three fields of (1) in-house systems to help aged or handicapped people live an independent life, (2) in-home care equipment systems suitable for advanced welfare oriented residences, and (3) user interface controllers to improve on operating sensation in a motor driven wheelchair. In field (1), studies involve the development of low floor residences for snowy cold regions, improvement on entrances for independent residences helping the inhabitants lead an independent life, and functionally excellent designs for handrails for steps, stairs, or bathrooms. In field (2), surveys are conducted concerning design improvements and their acceptability relative to a universal welfare equipment controller, optimum sound that welfare equipment alarms should produce, and transfer devices. In field (3), studies are made about motor driven wheelchair controllers. (NEDO)

  10. Report on a regional new energy vision establishment in Yatsuka Township; Yatsukamachi chiiki shin energy vision sakutei jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys and discussions were given on establishing a new energy vision in Yatsuka Township in Shimane Prefecture. For the survey on available amount of natural energies (sunlight and wind), all-weather insolation required for solar energy power generation was analyzed by using the NEDO information, and wind was analyzed based on observations at Matsue Meteorological Observatory, Sakai-minato Observatory, and Nakaura Water Gate. In discussing the system, power generation amount in the Matsue area was estimated for the case when solar cells of single crystal silicon plus amorphous hybrid type HIP-H48B1 are used. For wind power generation, power generation amount was calculated from observation values derived at the Nakaura water gate when wind mills with diameters from 2 to 10 m are used. Furthermore, calculations were performed on power amount generated uniformly by using a hybrid system using solar energy power generation and wind power generation. As a result of the discussions, a plan was established to introduce the new energies by means of a solar and wind energy hybrid power generation system to the greenhouse 'Green Stellar' symbolizing the Japan's largest peony production, being capable of year-round peony cultivation. The system is planned to be introduced to the town office building and other public organizations sequentially according to annual programs. (NEDO)

  11. Workshop on APEC virtual center for environmental technology exchange; APEC kankyo gijutsu koryu virtual center workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    At the 'policy maker workshop of the virtual center of APEC technology exchange' held in November 1997 in Osaka, Japan, it was agreed to organize study groups to discuss the scope of information provided by the virtual center, and to make common the classification systems and retrieval functions. In addition, the necessity was confirmed on international cooperation to promote establishment of virtual centers in different countries and territories. On the first day, Professor Ueda at the Kyoto University gave the basic lecture entitled 'global environment preservation and environmental technology transfer: problems and prospects'. Mr. Dan, the workshop manager gave the basic proposal entitled 'the future directionality of environmental technology exchange inside the APEC territories by using Internet'. Based on the basic proposal made on the first day, reports and discussions were given in the following sessions, where confirmation was made on the future directions. S1: establishment of the virtual centers in other countries and territories; S2: assurance of interchangeability of classification systems and retrieval functions in providing information, and S3: presentation of examples of inter-territorial exchange and the future directionality. (NEDO)

  12. Trend of advanced technology of micromachines in the USA; Beikoku ni okeru micro machine sentan gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In this research, the data of advanced technology of micromachines in the USA have been searched, collected, and arranged from the US patent information, technical journal information, and newspaper and general journal information. According to demand, the main undertaking information was interviewed from well-informed persons. The data were compiled as advanced technology trend of micromachines in the USA. Sensors are remarkably predominant in the elemental technology. There are also important topics in the fields of actuators, motors, lenses, devices, and structures. On the other hand, materials, etchings, packages, motive powers, and softwares are also important elemental technology in spite of their less information. From the viewpoint of usage, detection systems are remarkably predominant. Then, robots, processing systems, optics, analysis systems, motive power systems, medical systems, and acoustic systems are also important. From the viewpoint of industrial sector, the environmental items are predominant. Automobiles, medical treatments, and information communications follow the above. When new relationships to the secondary usage and tertiary usage are not found, it would be rather hard to express such a technology development trend more clearly.

  13. Achievement report on developing inverse manufacturing system in fiscal 1998; 1998 nendo inverse manufacturing system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a circulating type production system, or an inverse manufacturing system, to minimize the environmental load in the entire life cycle of industrial products from design to manufacturing, maintenance, recovery, and re-utilization. In developing the recycling information system, discussion and extraction were executed on the data to be exchanged between manufacturers and users in the inverse society. A new individual parts history control system was developed. In developing the recycling processing system, a prototype system was evaluated by using hypothetical data, wherein the possibility of improving the recycling processing efficiency and reducing the cost was verified. In addition, trial design was made on a recycling processing plant in consideration of the cost effect to get the future plant image. In fabricating the inverse manufacturing products, a prototype concept model was made for information terminal devices. Development was performed on such elementary technologies as the easy-to-disintegrate structure technology, self-integration connecting structure and environmental hysteresis detection system. (NEDO)

  14. FY 1999 report on the results on analysis of protein functions; 1999 nendo tanpakushitsu kino kaiseki seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at construction of the intellectual infrastructures for biotechnologies, in order to accelerate development of the Japanese technologies and activate their application to industries. Described herein are the FY 1999 results. These infrastructures are for functional analysis of protein which will be one of the key issues in genome analysis, and collection and analysis of biological information. This project includes a total of 9 research and development themes for four research categories: frequency analysis of gene expression (development of the gene expression profile database system for functional analysis of human genome, and analysis of the gene expression and protein functions by the ECA chip technology), function analysis by the biological model (high-performance analysis by the bio-project, database system for drug metabolizing enzymes, analysis of gene functions using mutant mice, and simple genome function analysis of murine individuals using the RNAi effect), protein expression (function validation of unknown human genes based on the useful biological model, and protein function analysis using multi-purpose destination vectors), and protein function prediction by the information science method. (NEDO)

  15. Report on the environmental safety evaluation sub-committee meetings in fiscal 1987; 1987 nendo kankyo anzensei hyoka bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The environmental safety evaluation sub-committee has held two meeting in the current fiscal year as described below. The first sub-committee meeting (August 25, 1987) was held for the agenda of the summary of future test plans, the result of overseas surveys in fiscal 1986, the results of tests in fiscal 1986, and the summary of the test plan for fiscal 1987. The major agendum of the second sub-committee meeting (February 23) was the interim reports on the overseas survey results and the safety tests in fiscal 1987. NEDO intends to ensure the labor hygiene for workers in coal liquefying plants, the effect of liquefied oil on users' health, and social acceptability of liquefied oil. Therefore, a safety test for liquefied oil in the primary hydrogenation process was performed provisionally on brown coal PP in the initial stage of operation, in addition to bituminous coal liquefied oil at the existing 1-t/d PDU. The main contents of the test performed by NEDO are based on the labor safety and hygiene law and the law related to regulation on the deliberation and manufacture of chemical materials. Different tests using guinea pigs were carried out on the total fraction mixed at the 1-t/d PDU, and each fraction of light and heavy oils, where the liquefied oil was verified to have minor degree of toxicity. (NEDO)

  16. Achievement report for fiscal 1982 on Sunshine Program. Coal energy; 1982 nendo sunshine keikaku seika hokokusho. Sekitan energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-07-01

    This research program consists of (1) the solid catalyst-aided reforming of various petroleum based oils and heavy coal oils into Solvolysis solvents and the secondary hydrogenolysis, (2) a search for pre-treatment for improvement on the sub-bituminous coal liquefaction yield, and (3) a search for measures for improvement on the brown coal liquefaction yield. Studied in this fiscal year are (1) the high-temperature short-contact time liquefaction of brown coal, (2) the role of catalyst support for selective upgrading of SRC (solvent refined coal), and (3) reforming of thermal melting feature of low rank coal by preliminary deashing at room temperature. In relation with Item (1), it is found that the dehydrogenation or reaction to carbonization of molecules involved in hydrogen donation is structure-sensitive but that thermolysis of coal is accelerated under high-temperature conditions to allow transfer hydrogen to contribute uniformly. It is deemed also that matching is excellent between hydrogen transfer and thermolysis, that the solvent dissolution level is elevated, and that the reaction short in duration inhibits consecutive polymerization reaction. These are supposed to be effective in improving on the liquefaction yield and in rendering heavy constituents lighter. In relation with Item (2), it is found that the experimentally manufactured catalysts are effective in reducing the weight of heavy constituents. In relation with Item (3), a carbonization reforming method is experimentally implemented in which the ash that affects carbonization is further removed by a pre-treatment at room temperature. (NEDO)

  17. Survey report on establishing a regional new energy vision in Gohoku Village; Gohokuson chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A regional new energy vision was established in Gohoku Village in Kochi Prefecture. Significance of this vision as a guideline for new energy introduction lies in preservation of natural environment, development promotion of the district, and building of a village strong against disasters. According to the discussion on energy availability in Gohoku Village, the expected usable amount will be about 5.13 million kWh/year by using solar energy power generation, about 2.25 billion kcal/year by utilizing solar heat, about 42 million kWh/year by utilizing wind energy, about 1.07 million kWh/year by using a small hydroelectric power plant, and about 31 million kcal/year by using wastes energy. The important new energy introduction projects are planned for introducing solar energy power generation, solar heat utilization, wind power generation, and small hydroelectric power generation in the area of 'Green Park Hodono' to make it a new energy model park (an ecology park), introducing solar energy power generation and solar heat utilization in the health and welfare center, day-service center, and special aged nursing home, and introducing clean energy fueled automobiles in official use. (NEDO)

  18. 1998 Annual Study Report. Standardization of color reproduction management; 1998 nendo seika hokokusho. Iro saigen kanri (color management) no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Standardization of color reproduction management is aimed at realization of the most urgently needed areas of the color reproduction management for international standardization. This R and D program is aimed at drafting the standards for color information devices and their characteristics, and proposing the drafts. Factors which deteriorate color reproduction stability of input and output devices are classified and analyzed, devices for evaluation are selected, and extents of the deterioration are measured and evaluated, in order to extract the problems involved in the color reproduction models for the current input and output devices. Standardization of color management on the multi-spectrum color images is attempted for business printing, where effectiveness of a fluorescent ink containing a fluorescent material is noted for expansion of the color reproduction range for printing color images with the conventional YMCK inks. Basic aspects of the fluorescent colors are measured, to verify the methods for measuring fluorescent body colors. As a result, new knowledge is obtained. The standard images for flesh color evaluation are produced, and the methods for analyzing the data obtained by the tests, including the subjective tests, are established. These lead to establishment of the standards for preferred flesh color of the yellow races. (NEDO)

  19. FY 2001 report on the new energy vision of Ajigasawa Town; 2001 nendo Azigasawa machi shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Ajigasawa Town, Aomori Prefecture, an investigational study was conducted of the amount of energy demand of the town, potential introduction of new energy, etc., and a new energy vision was worked out. The population of Ajigasawa Town was 13,551 according to the results of the national census taken in 2000, which is slightly decreasing. The energy demand is broken down into 40.1% in the transportation sector, 35.4% in the industrial sector and 24.5% in the commercial/residential sector, depending on petroleum (81.8%) and electric power (13.1%). The CO2 emission amount from the above is estimated at 26,210 t-C/y in total. In the model project for new energy introduction, the following were selected: wind power generation for the filtration plant of water supply system/night soil treatment plant/funeral hall/comprehensive park/seed and seedling center; photovoltaic power generation for the trip village for youth/elementary schools; fuel cell/hybrid car for Ajigasawa town office; micro-hydroelectric power generation for nursery; natural gas cogeneration for the insurance welfare center. (NEDO)

  20. Fiscal 2000 achievement report. Welfare technosystem research and development (Mizusawa); 2000 nendo walfare technosystem kenkyu kaihatsu (Mizusawa) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For assisting aged people, healthy and living alone, in living without help, activities were conducted for (1) an electrical transmission experiment connecting residences (two, inhabited for the experiment) and a remote location (Techno-House) and (2) the development of a home server equipped with an electrocardiograph. Under item (1), data collected by sensors (occupancy sensor, open/close sensor, flame sensor, waterflow sensor) installed at the residences occupied by aged persons living alone were forwarded to Techno-House via CATV (cable television) and analyzed for the study of elderly people's behavior and daily life pattern. It was found that using this system the behavior of elderly people living alone might be detected even in the absence of their intention to report or communicate. Under item (2), an Ni-based electrode sheet was fabricated and installed in a bed and, via the sheet and a CATV channel, cardiographic waveforms were transmitted to Techno-House where the data were put into an analyzer for the examination of the elderly person's physical conditions. (NEDO)

  1. Summary report of the overseas researcher invitation program in FY1996; 1996 nendo kaigai kenkyusha shohei jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To exchange research information, Mr. Koernaen Inif was invited from the Ministry of Industry and Commerce, Indonesia in the period between 4th November in 1996 and 4th February in 1997 as a part of the overseas researcher invitation program in FY 1996. The research theme is `Investigation of low cost removal method of COD and BOD from industrial waste water: Biodegradation of lignin in the waste water from pulp industry using anaerobic bacteria.` The institute of the invited researcher has promoted investigations for improving water quality of the Surabaya River. The largest reason of the water quality pollution of the Surabaya River is caused by the waste water from paper and pulp industry, and pollutants are COD and BOD. In major factories with economic margins, waste water treatments have been conducted, which do not satisfy the waste water standard of factories. In this investigation, the treatment technology information of industrial waste water were collected. The information were summarized for contributing to the future research and development in Surabaya. The objective was to obtain the biodegradation techniques of lignin using anaerobic bacteria. 51 refs., 7 figs., 5 tabs.

  2. Fiscal 1995 geothermal development promotion survey. Natural environment survey report; 1995 nendo chinetsu kaihatsu sokushin chosa. Shizen kankyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In Candidate C area for the geothermal development survey, the natural environment was surveyed and `the secondary landscape assessment` was summed up in which places proposed for drilling of large-size wells and for construction of power generation facilities are extracted and a simulation of the landscape is conducted. The area for survey is the Shiramizu-gawa region in the south of Lake Akan, Akan-cho, Akan-gun, Hokkaido. The field survey was carried out about three items of landscape, plants and animals during the June-November period, 1995. As to the flora, diverse florae including vegetation unique to alpine areas, wetlands, and fumarole surrounding areas were found in the region, which is covered with summer-green broad-leaved forests or mixed forests of coniferous and broad-leaved trees. As to the fauna, faunae inhabitant of the highly natural forests were found including black woodpeckers and mountain hawk eagles. As a result of studying the places proposed for geothermal development from the above-mentioned survey, two places were picked up in the west of the survey area, where geothermal development is comparatively less influential in the natural environment and landscape and there is a high locational adaptability. 19 refs., 56 figs., 49 tabs.

  3. Fiscal 2000 pioneering research report on the 3D nanotechnology; 2000 nendo 3D nano technology sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted of the 3D nanotechnology which is a technology that aims to create novel functions and to enhance functions in mechanical engineering through the control of large-area 3-dimensional nano-scale structures. In this fiscal year, trends of research and development and technological tasks were surveyed from the viewpoint of nanomanufacturing technology. Basic processing technologies were surveyed, which included the laser-aided or light-aided micromachining technology, chemomechanical processing technology, and nanoparticle beam-aided processing technology. In the research of mass production technologies, the nanostructure transfer technology superior in capability to the conventional photolithography was taken up. Nanomanipulation technologies were also surveyed, such as atomic/molecular-level observation, assessment, processing, fixation, and the like. Technologies involving machine elements and structures were surveyed, when microactuators and micromechanisms were studied, such as nano-scale functional films. Lastly, a proposition was made about research and development tasks for the future and about how to work on such tasks. (NEDO)

  4. Report on a comprehensive research study (home welfare apparatus system - lifestyle); Sogo chosa kenkyu (zaitaku fukushi kiki system - lifestyle) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    An investigational study was conducted on evacuation of aged people at disaster, life maintenance, and welfare apparatus which is applicable to the future change of life style and its harmony with the living environment. In the study of care apparatus, reported were the apparatus operational interface using the indoor environmental control simulation system, safety on moving/transfer equipment, experiment on opening/closing power of sliding doors, study of electric-driven wheel chairs, study of the sitting pressure of various wheel chairs, etc. In relation to the living environment, the paper reported planning of houses introducing care apparatus, assessment of system kitchen, disaster prevention measures for aged/handicapped people, study on performance of the combined use in the living environment, assessment of drops in floor level in the living space, etc. Also reported were assessment on the living environmental control state of serious paralyzers of the limbs, study of a network to support care at home, etc. 48 refs., 117 figs., 29 tabs.

  5. FY 2000 report on the results of the Clean Energy Festa; 2000 nendo clean energy festa kekka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For understanding/education for the spread of clean energy vehicles and promotion of recognition/understanding of new energy, the Clean Energy Festa was conducted in Yokote, Akita prefecture, Nagoya, Osaka, Yokohama and Hiroshima, and analysis by questionnaire survey was made. Written below were the details of the questionnaire survey. How you knew of the exhibition: 'by leaflets from school, etc.' is 50.4%; why you came to the exhibition: 'there is something enjoyable about it' is 32.5%; What attracted you: 'solar car workshop' is 34.8%; How much you have known of new energy: 'somewhat known' is 41.5%; How much you understood new energy after seeing the exhibition: 'somewhat understood' is 60.9%; How much you became aware of new energy: 'a little deeply aware' is 59.8%; How much you understood clean energy car after seeing the exhibition: 'somewhat understood' is 58.7%; How much you became aware of clean energy car: 'a little deeply aware' is 60.9%. (NEDO)

  6. Geothermal development promotion survey. No. B-3 Kumaishi area; Chinethu kaihatsu sokushin chosa seika hokokusho. No. B-3. Kumaishi chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper summarizes the result of a geothermal resource survey carried out from fiscal 1995 through fiscal 1997 in the Kumaishi Area located in the western center of Oshima Peninsula in the south western part of Hokkaido. The survey for this area was performed with an objective to search the spread of high temperature area continuing from the adjoining Yakumo area where the highest temperature of 233 degrees C has been confirmed in a structural test well (N63-YK-6), to identify high water permeating areas in great depth points underground, and to find possibility of existence of geothermal resources. The survey included geological and alteration zone survey, geochemical survey, gravitation exploration, electromagnetic exploration, drilling and temperature logging of five structural test wells, water injection test, temperature restoration test, core survey and hot water survey. Also performed were environmental effect survey, rock age measurement, alteration age measurement, and fluid inclusion test. As a result of the survey, it was identified that the verified geothermal hot water has been stored in granites with poor water permeability, whose low temperature has not formed convection systems spreading in wide areas despite having been heated, making each system exist in small scale independently. It was estimated that the possibility is low to expect geothermal power generation. (NEDO)

  7. Report for fiscal 1998 on feasibility study for introduction of electric automobiles; 1998 nendo denki jidosha donyu kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys have been made on the characteristics of environmentally harmonizing automobiles, and the status of development and introduction thereof inside and outside the country. Discussions were given on the possibility of introducing electric automobiles in Japan. In developing environmentally harmonizing automobiles in Japan, works have been executed on low pollution type components such as lean burn engines, electric automobiles, gasoline engine and electric motor hybrid cars, methanol fueled cars, and fuel cell automobiles. Some of them are already in use in spite of their high price. In America, a cooperation project for the next generation cars has been implemented by mobilizing industrial, academic and governmental organizations. Based on the achievements thereof, the car makers have announced their original advanced cars respectively. In the EU, development of low exhaust gas cars and zero emission cars is being carried out jointly by the related industries setting years 2003 to 2005 as the target. An urban type traffic system utilizing electric vehicles, and a traffic system dividing movements of short distance and long distance are proposed as the means to introduce the future electric automobiles. (NEDO)

  8. Fiscal 1997 achievement report. Research and development of synergy ceramics; 1997 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development is conducted on two subjects, that is, 1) hyper organized structure control technology and 2) structural element control technology. In addition, joint research and development is conducted on the creation of new materials by hyper organized structure controlling, hyper organized structure controlling for ceramics by a structurization reaction process, designing of precursors to ceramics, and the hyper organized structure control for ceramics by nanostructure process control. The joint research and development endeavors further deal with re-entrusted projects which involve researches on sintered structure control by powdery particulate structure control; dynamic process of synergy ceramics; oxynitride liquids, glasses, and glass-ceramics; and multifunctional ceramic laminates for engineering applications. Under subject 1), researches are made on the development of precursors into ceramics by utilizing chemical reactions of organic metal compounds, and analyses are conducted into the effects, exerted by the molecular structures of precursors and the conditions of a reaction for their development into ceramics, on the microstructures and various properties of the ceramics to be composed. Under subject 2), high strength, great hardness, and high resistance to wear are realized by allowing the precipitation of nano-particulates in crystals of a fine and very compact sintered body of alumina. (NEDO)

  9. Fiscal 1974 research report. General research on hydrogen energy subsystems; 1974 nendo suiso riyo subsystem sogoteki kento hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    Based on the contract research 'General research on hydrogen energy subsystems and their peripheral technologies' with Agency of Industrial Science and Technology, each of 7 organizations including Denki Kagaku Kyokai (Electrochemical Association) promoted the research on hydrogen energy subsystem, combustion, fuel cell, car engine, aircraft engine, gas turbine and chemical energy, respectively. This report summarizes the research result on the former of 2 committees on hydrogen energy and peripheral technologies promoted by Denki Kagaku Kyokai. The first part describes the merit, demerit, domestic and overseas R and D states, technical problems, and future research issue for every use form of hydrogen. This part also outlines the short-, medium- and long-term prospects for use of hydrogen and oxygen energy, and describes the whole future research issue. The second part summarizes the content of each committee report. Although on details the original reports of each committee should be lead, this report is useful for obtaining the outline of utilization of hydrogen energy. (NEDO)

  10. Report on the comprehensive investigational research (at-home welfare apparatus system); Sogo chosa kenkyu (zaitaku fukushi kiki system) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    An investigational study was conducted on the research and development of an at-home welfare apparatus system. In this study, a stay experiment was carried out on whether aged or handicapped people can easily live in welfare houses into which at-home welfare apparatus was integrated, using high-tech at-home nursing apparatus systems (welfare techno house: WTH) which were installed at seven places in Japan based on `the development of a system supporting independent excretion.` In addition, the following were conducted: experiments on at-home welfare apparatus in terms of the evaluation of performance/operability/safety, physical physiology reactions, nursing burden/estimate of independence, two-way communication, examination of housing environments, etc. In WTH Chofu, a test on evaluating welfare apparatus was conducted by people with limbs paralysis and healthy case workers. In WTH Sapporo, by a working group studying biological information, examinations were made on the situation of standing up of healthy adults, old people and people with paralysis of one side of the body from various types of chairs, beds, wheel chairs, portable toilets and sitting down on them. An examination was also made on harmony with psychological function and physically adaptable function by a working group studying at-home nursing apparatus. 75 figs., 15 tabs.

  11. Research report of innovation of industrial technology in FY 1996; 1996 nendo sangyo gijutsu no innovation chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Remarkable innovations of the Japanese industry in various fields have been extracted and evaluated during the 50 post-war years. In this report, a method of capturing the innovations of industrial technology is examined. It is essential to clarify the social role of industrial technology, and the original views of this research are indicated by focusing on the innovation process in order to clarify the connections between those of mutual industry, technical management, man-power, and unique Japanese technology. The innovations achieved by the Japanese industry during post-war 50 years are classified into eight categories, i.e., automobiles, iron, aero-space/railways, machines, national land/energy, chemicals/fine ceramics, electronics/information/communication, and life, to clarify the technological progress in each field. In Japan, the industrial technology has been developed with learning from fundamental researches in Europe and the USA. In the future, it is necessary to independently develop industrial frontier. 4 figs., 47 tabs.

  12. Basic survey report on regional new energy vision for Ehime Prefecture; Ehimeken chiiki shin energy vision kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision has been formulated to establish guidelines for popularizing and utilizing new energy which generates but a small amount of environmental impact. The results of surveys conducted in this connection are described in five chapters, which cover (1) the trend of new energy, (2) current situation of new energy in Ehime Prefecture, (3) calculation of the existing amount and available amount of new energy, (4) calculation of the introducible amount of new energy, and (5) the basic policy toward the introduction of new energy. Part (4) covers solar energy, wind energy, waste-derived energy, temperature difference energy, minor scale hydroelectric power generation, biomass energy, and like others. It states that a total of 540,000 kl/year will be available in terms of oil, equivalent to approximately 6% of Ehime Prefecture's 1997 energy consumption, and that it is expected that in fiscal 2010 photovoltaic/passive solar energy utilization, cogeneration, and wind power will yield 152,000, 314,000, and 27,000 kl/year respectively. (NEDO)

  13. Summarized achievement report on the Sunshine Project in fiscal 1980 (Hydrogen energy); 1980 nendo seika hokokusho gaiyoshu. Suiso energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-04-01

    This paper summarizes the achievement report on the Sunshine Project in fiscal 1980 for hydrogen energy research. In hydrogen manufacturing using the electrolytic process, improvements were made on membranes and electrodes. Solid electrolyte electrolysis is also under research. Researches are continued on reaction, separating operation, and device materials for the iodine system cycle in the thermo-chemical method. In the iron system cycle, a reaction experimenting equipment was fabricated on the trial basis, and tests and evaluation were performed on the material and heat balances. In the mixed system cycle, researches on the light irradiation electrolytic process were continued, whereas the light collecting rate was raised by using a lens to increase light intensity, having enhanced successfully the reaction rate to 60 to 80%. A heat diffusion column for HI decomposition and separation (hydrogen acquisition) was discussed in terms of chemical engineering. Development works are continued on metal hydrides for hydrogen transportation, and durability tests are also being performed. Same applies to hydrogen storage. A model burner was fabricated on the trial basis, and catalytic combustion was studied as development of a combustion technology that matches the requirements for safe hydrogen combustion and suppression of NOx emission. Searches were continued on catalysts and solid electrolyte materials for fuel cells. Thin film sold electrolyte fuel cells constructed by using the evaporation process are also being studied. The paper also describes measures for hydrogen safety assurance and researches on energy systems. (NEDO)

  14. FY 1988 report on the committee of the Coal Gasification Committee; 1988 nendo sekitan gaska iinkai hon'iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    The paper reported activities of the committee of the Coal Gasification Committee in FY 1988. In the 1st committee meeting, report/discussion were made on the outline of the FY 1988 research plan on the coal gasification technology development. The distributed data were those on the development of entrained bed coal gasification power generation plant (the state of the development of a 200t/d gasification power generation pilot plant), the results of the operation using entrained bed coal gasification equipment, development of coal utilization hydrogen production technology (design/construction of pilot plant) and development of coal utilization hydrogen production technology (support study of pilot plant, study using small equipment). In the 2nd committee meeting, report/discussion were made on activities of sections such as the gasification power generation section and gasification technology section and the state of progress of the coal gasification technology development. The distributed data were those on the development of an entrained bed coal gasification power generation plant, support study of the development of an entrained bed coal gasification power generation plant, etc. (NEDO)

  15. Interim evaluation report on research and development of automatic sewing systems; Jido hosei system no kenkyu kaihatsu chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The research and development project for automatic sewing systems is aimed at establishing the techniques necessary for developing (automatic sewing systems) which efficiently produce diversified types of products in small quantities, to cope with various requirements, e.g., diversified consumers' needs and reduced cycle periods. This project covers R and D of the sewing preparation/processing, sewing/assembling, cloth handling, and system management/control techniques. The program for developing the total systems and elementary techniques draws the conceptual designs of their functions, performance and shapes, to outline the overall R and D project. The programs for the individual elementary techniques include studies on their basic functions and performance; design works from the basic designs to determine the specifications to the detailed designs of the devices to be developed; construction of the test units on a trial basis; and function confirming tests to confirm operability of the unit components and device performance, where these works are simultaneously implemented. This paper describes the interim results of evaluation of the elements developed for the elementary techniques, summarizing the results obtained so far. It is concluded that most of the targets of the R and D themes are sufficiently achieved by the end of FY 1987, and that the project can be now advanced to the next phase, construction of the test plants. (NEDO)

  16. Report of results of contract research. 'Research on magneto hydrodynamic (MHD) generation'; MHD hatsuden system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    Examination was conducted in detail on an MHD generation system by coal combustion, with the results reported. Concerning a gas table calculation program in coal combustion, it was prepared assuming 100% slag removal ratio in the combustor as the primary approximation. A combustor for MHD generation needs to efficiently burn fuel using high temperature pre-heated air as the oxidant, to fully dissociate/electrolytically dissociate seed, and to supply to the generation channel a high speed combustion gas plasma having a high electrical conductivity which is required for MHD generation. This year, an examination was conducted on technological problems in burning coal in an MHD combustor. As for the NOx elimination system in an MHD generation plant, an examination was made if the method studied so far in MHD generation using heavy oil as the fuel is applicable to coal. Also investigated and reviewed were various characteristics, change in physical properties, recovery method, etc., in a mixed state of seed and slag in the case of coal combustion MHD. (NEDO)

  17. International Workshop on Carbon Cycling and Coral Reef Metabolism; Sangosho no tanso junkan ni kansuru kokusai workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-16

    The paper described the International Workshop on Carbon Cycling and Coral Reef Metabolism which was held at Miyako-jima, Okinawa Pref. on October 17-24, 1995. In the workshop, researchers got together which are involved in marine chemistry, marine biology, coral ecology, and environmental science, and discussed the carbon cycling and metabolism of coral reef. Discussions were made on what the coral reef ecosystem is, and what the definition of a sink or a source for CO2 is. Also discussed were scales of how much time and space should be considered to make these issues clear. Further, it was proposed that it was necessary to investigate carbon balance of both the whole system and the components of the system and to keep track of mass transfer among neighboring components of the system. Seventeen presentations were given. The workshop obtained a definite consensus on carbon balance of the coral reef system. 123 refs., 39 figs., 9 tabs.

  18. Survey research report by the hydrogen occluding alloy utilization development committee; Suiso kyuzo gokin riyo kaihatsu iinkai chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    This report summarizes the FY 1984 survey research results, issued by the hydrogen occluding alloy utilization development committee. The basic property subcommittee is responsible for collecting published data related to the basic properties of metal halides as much as possible, and pigeonholing them to have the data which can contribute to development of the new alloys for basic researches and engineering applications of hydrogen occluding alloys. The subcommittee members have collected these data. The common theme subcommittee has planned to collect the P-C-T diagrams of the hydrogen occluding alloys and new alloys as much as possible, for the designs, development, production and system designs of the hydrogen occluding alloys. The P-C-T diagrams have been collected for a total of 340 types of alloys, which fall into the broad categories of Mg-based, TiFe-based, TiMn-based, other Ti-based, rare-earth-based, Zr-based, Ca-based and others. The analytical methods have been also investigated while collecting P-C-T diagrams. (NEDO)

  19. Workshop on APEC virtual center for environmental technology exchange; APEC kankyo gijutsu koryu virtual center workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    At the 'policy maker workshop of the virtual center of APEC technology exchange' held in November 1997 in Osaka, Japan, it was agreed to organize study groups to discuss the scope of information provided by the virtual center, and to make common the classification systems and retrieval functions. In addition, the necessity was confirmed on international cooperation to promote establishment of virtual centers in different countries and territories. On the first day, Professor Ueda at the Kyoto University gave the basic lecture entitled 'global environment preservation and environmental technology transfer: problems and prospects'. Mr. Dan, the workshop manager gave the basic proposal entitled 'the future directionality of environmental technology exchange inside the APEC territories by using Internet'. Based on the basic proposal made on the first day, reports and discussions were given in the following sessions, where confirmation was made on the future directions. S1: establishment of the virtual centers in other countries and territories; S2: assurance of interchangeability of classification systems and retrieval functions in providing information, and S3: presentation of examples of inter-territorial exchange and the future directionality. (NEDO)

  20. Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1982 reported. This year is the final year of this research; therefore, reexamination was made from the practical standpoint on the R and D of coal fired MHD generation, evaluating the present technological level as well as clarifying the development procedures, with proposals made as to the R and D from now on. The present technological level in the practicability is still in the basic stage, where the essential problem is the development of combustors, air heaters and generation channels in particular. An examination was conducted for the problems, procedures and period of the development for each component equipment, with the results provided as materials for studying the path to the experimental plant of 100 MW heat input. In the method of proceeding with the R and D in the future, it was decided as essential, in order to enter the stage of the experimental plant from the element technology development, that R and D is carried out on the unestablished component technology, making sure that no excessive risk is taken in scaling up to the next stage. (NEDO)

  1. Report on new energy vision for fiscal 2000 in Nanno Town (Gifu Prefecture); 2000 nendo Nannocho shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established in Nanno Town, upon investigating the existence quantity and utilization possibility of new energies, and from a viewpoint of reduction of air pollutants, and assurance of independent energy resources. The vision was established with the residents' participation as the base, while keeping consistency with the 'Nanno Town's new century development plan, 2010'. The activity achievements were put into order by the following six items: 1) necessity of introducing new energies, 2) the current status of Nanno Town, 3) energy demand quantity in Nanno Town, 4) possibility of introducing the new energies, 5) establishment of the introduction project, and 6) assignments and measures toward realization of the vision. Item 4) is composed of the summary of new energies in the district, new energy existence quantity in Nanno Town, and the residents' consciousness. Investigations were carried out on utilization possibilities of energies from solar beam, wind power, bio-mass, and wastes. The new energy existence quantity is estimated to be 5,005 kl/year converted into petroleum, as solar heat for general houses, 1,132 k/year as bio-mass, and 329 k/year as wastes. (NEDO)

  2. FY 1981 Report on the results of Sunshine Project. Coal energy; 1981 nendo sunshine keikaku seika hokokusho. Sekitan energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-07-01

    This report presents the results of (researches on solvolysis liquefaction mechanisms and reaction promotion with oil- and coal-based solvents), conducted as part of the research and development project for coal liquefaction techniques. The FY 1981 program includes researches on (1) the effects of liquefaction reaction conditions on liquefaction yield and production of light products for coal species of low degree of carbonization, including brown coal, (2) the effects of pretreatment of coal on its liquefaction reactivity, and (3) up-grading of the solvolysis coal liquid (SCL). For the item (1), HA240 (hydrogenated Ashland's A240) is used to investigate its liquefaction capacity for various coal species of low degree of carbonization, including brown coal. For the item (2), the effects of pretreatment in a hot water bath with reflux was investigated for sub-bituminous coal in the FY 1980. In the FY 1981, various pretreatment methods are attempted for enhancing liquefaction reactivity of brown coal. As a result, it is found that ash content of brown coal is decreased to one-third of the initial level, when it is treated in a diluted hydrochloric acid bath with reflux. For the item (3), SCL hydrogenated by Birch reduction (B-SCL, 1) is compared with H-SCL with respect to properties, structures and thermal crackability, to discuss the items required for the catalyst to be used in the second stage by clarifying effectiveness of the catalyst. (NEDO)

  3. Fiscal 2000 achievement report. Welfare technosystem research and development (Chofu); 2000 nendo welfare technosystem kenkyu kaihatsu (Chofu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development efforts are exerted to realize (1) a variable function residential circumstance system for the aged people and (2) a medical welfare and life assisting information system for helping the aged or handicapped people lead an independent life. Under item (1), a variable function residential circumstance system under which functions of the residence may be changed dependent upon inhabitants' degree of debility will be developed, and an information system will be developed under which medical welfare assistance and life assistance are integrated. Under item (2), residences, welfare appliances, and nurse/attendant assisting systems will be assessed and examined. In fiscal 2000, under item (1), a variable function re