WorldWideScience

Sample records for hokokusho hikari danso

  1. Achievement report for fiscal 1998. Optical tomographic system; 1998 nendo seika hokokusho. Hikari danso imaging system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Evaluations were given on spatial resolution and measurement time of an optical tomographic system by using the developed 64-channel time-resolved spectroscopy and an image reconstruction algorithm. With respect to the spatial resolution, the target value of 1 cm was verified from tomographic images of a phantom with a diameter of 10cm, simulating a neonate. The measurement time achieved 20 minutes, being one third of the target value. In installing the equipment at Hokkaido University, speeds of the optical switches and attenuators were increased to have reduced the measurement time to one minute. For installation at Kanagawa Rehabilitation Center, development has been made on a nano-second light pulser, whose average beam quantity has been increased to 40 times, and improvement has been given on the optical switches, the attenuators, and the indication software, by which the measurement time was decreased further by 30 seconds than that at Hokkaido University. In performing the clinical evaluation, the evaluation protocol resolved by the Experiment Evaluation Special Committee was submitted for deliberation at the Medical Welfare Device Clinical Evaluation Committee. Upon having been authorized by the Committee, the clinical evaluations were performed at Hokkaido University and the Kanagawa Rehabilitation Center. (NEDO)

  2. Achievement report on research and development of medical and welfare equipment technology. Optical tomographic imaging method; Iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Hikari danso imaging system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    The aim is to develop a method of processing oxygen concentration distribution in human organs into an image by computed tomography using near infrared rays capable of transmitting through living tissues. Since the photoabsorption spectra of hemoglobin etc. in blood vary according to the degree of their oxidation, an oxygen concentration level is determined by measuring the magnitude of the variation. In the imaging method named in the title, the object is irradiated with picosecond-level near infrared pulses from all directions successively, the pulses after transmission through the object are measured at all directions at a picosecond-level time resolution, and the distribution of pulse scattering and absorption characteristics are subjected to algorithmic calculation, the outcome is converted into oxygen concentration levels, and an image is obtained. A 64-channel time resolution measurement system is constructed, and is applied to living tissue models (phantoms) and animals, and an image is obtained and evaluated. On the basis of the result, a patient is examined for clinical evaluation, and an image reflecting the distribution of variations in hemoglobin oxygen concentration is obtained for the head of the adult patient. A spatial resolution of 1cm is achieved in case of a phantom 10cm in diameter. In the case of 64 channels, measurement takes approximately 20 minutes and mapping image data measurement takes approximately 7 minutes. (NEDO)

  3. Visualising ‘Unacceptable’ Lives? The Moving Story of Hikari to tomo ni (With the Light: Raising an Autistic Child, 2001-2010

    Directory of Open Access Journals (Sweden)

    Mio Bryce

    2014-08-01

    Full Text Available In this article we will interrogate the notion of ‘the unacceptable’ by tracing the movement of a particular text – a series of manga novels by Keiko Tobe entitled Hikari to tomo ni (With the Light: Raising an Autistic Child, 2001-2010 – from serialisation in a Japanese women’s magazine, to publication in Japanese as a series of manga novels, to publication in English in book form. In following this text – a narrative of parenting a child with autism from birth to adolescence - through its various contexts of production and reception, we want to raise doubts about a shibboleth of a particular kind of media and cultural studies - that the unacceptability of a text in mainstream popular or political contexts makes it particularly interesting from a scholarly point of view. Our account of Hikari to tomo ni’s movement through its various contexts of publication and reception supports Mitchell and Snyder’s argument that disability politics does not allow easy categorization of representations into ‘straightforward catalogues of “acceptable” and “unacceptable”’ (Mitchell and Snyder, 2001, 213. The context of the original publication of the serial in Japan demonstrates the barriers to publication of manga centring on experiences of disablement. Such stories were seen as commercially unacceptable not only because they seemed difficult to market as entertainment, but also because they required the use of contested language which might draw unprofitable attention. Tobe’s work and its enthusiastic reception by the readers of For Mrs. ultimately overcame publishers’ qualms. Yet the visual strategies adopted by Hikari to tomo ni and the reception of this manga in an English language context demonstrate the way its writer and publishers manage its apparently unacceptable theme.

  4. FY 1998 annual report on the research and development of non-linear, opto-electronic materials; 1998 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The final assessment of researches on non-linear, opto-electronic materials was conducted in FY 1988. These researches are evaluated as the world-level basic researches, high in potential of giving ripple effects on various areas. The R and D themes are organic, low-molecular-weight materials; technology for orientation-controlled crystal growth; conjugated polymer films; microcrystallite-doped glasses using vapor deposition and stuffing method; glass composite materials using sol-gel method and ultra-low melting point glass; nanoparticle-dispersed glasses using super-cooling technology; materials dispersed in organic compounds; organic superlattice formation; three-dimensionally superstructured materials; and comprehensive surveys and researches. The researches and surveys on the common basic techniques were recommissioned to Universities of Tokyo, Keio Gijuku, Nagoya, Tohoku and Hokkaido. These themes are analytical methods for non-linear optical characteristics; morphology-controlled crystal growth of nonlinear-optical organic materials and fundamental studies on all-optical devices; large enhancement of optical nonlinearity and its mechanism in nanocrystals embedded in matrices; improvement of organic materials for high performance; and ultrafast nonlinear optical processes and their application for controlling ultrafast optical pulses. (NEDO)

  5. Achievement report for fiscal 1990 on research and development of photoreactive materials; 1990 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Activities were performed with an objective to establish fundamental technologies related to photoreactive materials capable of ultra-high density and high resolution indication by controlling structures and assemblies of molecules by using light. The activities were taken in the four fields of elucidation of photoreactive mechanisms and fundamental properties, development of the materials, material processing and constituting technologies, and evaluation technologies. Specifically speaking, the activities were developed on the multiplexing technology applicable to ultra-high density recording, sensitivity responsiveness, and material stability in photochromic materials and photochemical hole burning (PHB) materials. For the photochromic materials, development was performed on photochromic materials to form associations, and on a thin film forming technology by means of the organic molecular beam epitaxial process. For the PHB materials, research was implemented on use of the materials at elevated temperatures, development was made on quinone-based materials, research on enhancement of multiplexity, development on porphyrine-based materials, and research on the organizing technology. In the research of the use at elevated temperatures, development was progressed on a material that can retain under the liquefied nitrogen temperature the status of wavelength multiplexed recording that has been formed under the liquefied helium temperature. (NEDO)

  6. Report on achievements in fiscal 1999. Research and development of nanometer controlled optical disk system; 1999 nendo nanometer seigyo hikari disk system no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Organizational strengthening is urged in industrial technological power in information recording area which is comparable with information communications being the main pillar of the innovation in the information technology in Japan. Extremely large expectations and heavy responsibilities are placed on the next generation optical memory technology, which is one of the strong points of Japan who plays a part in the above information recording area. The present project has been performing organizational research and development to achieve creation of new industries, with the following research themes as the main subjects: (1) nanometer controlled optical memory technology, (2) magnetic section responsive and three-dimensional optical memory, (3) ultra precision pit depicting technology, and (4) ultra precision pit measuring technology. The project is two years old this year, in which it was aimed to 'develop an optical memory technology with recording density of 100 Gb/in{sup 2} or more, transfer velocity of 100 Mbps or higher, and access time of 10 ms or less'. In order to achieve and establish the interim target set for fiscal 2000 among the above aims, intending 'trial fabrication of a disk having recording density of 40 to 50 Gb/in{sup 2}, the technical problem extraction and the specifications to realize a 100 Gb/in{sup 2} system', fiscal 1999 has performed researches on 'density and accuracy improvement on the prototype disk by improving the existing devices and introducing new devices'. This paper reports the developmental research theme No. 1. (NEDO)

  7. FY 1991 Report on the results of the researches on nonlinear photoelectronic materials; 1991 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The nonlinear optics with light-light conversion and electro-optical effects are expected to be the optical materials of the next generation for their functions of, e.g., conversion of the infrared laser beams into visual light, and optical switching. The efforts are directed to development of the procedures for exploring and designing various raw materials, and technologies for synthesizing the raw materials and for producing and evaluating the materials, in order to develop highly nonlinear, high-speed responding materials. Three areas are studied; for the organic materials, the chiral nonlinear effects are demonstrated and the new procedure for determining electrical susceptibility ({gamma}) is developed; for the dispersed materials, highly nonlinear susceptibility of glass dispersed with fine particles of semiconductors, e.g., CuCl, is realized, and possibility of controlled dispersion of fine semiconductor particles in an organic polymer is established; and for development of the superlattice-based materials, the layered structures of thin organic superlattice films are studied, the thin semiconductor films of high purity and little defects are prepared, and development of the three-dimensional structures is started. The individual researches are conducted, 3 for the organic materials, 4 for the dispersed materials, and 2 for the superlattice-based materials. The targets of susceptibility and response are 10{sup -8}esu or more and 10ps or less, respectively. (NEDO)

  8. Report on investigations and studies on chemical conversion of photo-energy; Hikari energy no kagakuteki henkan ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This paper summarizes problems in utilization of solar energy, their solutions, features, the currently achieved results, and prospects. With regard to water decomposition using semiconductors, simultaneous generation of hydrogen and oxygen has already been achieved, and there is high possibility of raising the efficiency by improving catalysts. Water decomposition using metal complexes has acceleration of charge isolation as the largest problem, whose prospect of solution is not necessarily bright at the present time. Photo-catalytic reaction is a field to be discussed as one means of developing a new synthesizing method from the viewpoint of organic synthetic chemistry. Conversion into electric energy that uses a photovoltaic process has high efficiency, and is a field to be noted. In photo-energy conversion by means of photo-synthesis, living organisms performing hydrogen production at high efficiency have been discovered. Important studies include the studies in terms of chemical engineering using these living organisms, improvement of breeds by gene manipulations, and studies that utilize living organisms or part of the constituting components. (NEDO)

  9. Achievement report on research and development of optics-aided measurement/control system; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    The project aims to establish technologies for putting the above-named system to practical use. Such a system will measure, transmit, and control, with safety and stability by use of optical technologies, industrial process related information to be generated in certain areas such as industrial complexes and very large plants, the information including images, temperatures, flow rates, constituents, etc. Total system evaluation was performed in demonstration tests for appropriateness conducted for 32 systems in fiscal 1980 and 10 systems in fiscal 1981. Studied in the development of element technologies are opto-electronic integrated circuits (OEIC), semiconductor laser devices, light-intercepting devices, optical transmission paths, dielectric light switches, and optical sensors. For OEIC, in particular, since it is believed to be the nucleus of an optical application system, an optical technology joint research office is established, where efforts center on the substrate crystal growth technology, process technology, and crystal/process evaluation technology. (NEDO)

  10. Fiscal 2000 achievement report on the research and development of nanometer controlled optical disk system; 2000 nendo nanometer seigyo hikari disk system no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Development proceeded of nanometer controlled optical memory technologies as part of systematic research and development aiming at the reinforcement of industrial technology power in the field of data recording. Activities were conducted in the four fields of (1) high density signal processing technology, (2) high performance disk materials technology, (3) disk substrate fabrication technology, and (4) signal detection technology. Discussed in field (1) were multivalue ROM (read only memory) disk signal regeneration, SIL-LBR (solid immersion lens-laser beam recorder), dry etching process using RIE (reactive ion etching), SHG (second harmonic generation) blue laser, and a multivalue ROM disk evaluation system. Studied in field (2) were the evaluation of ROM disk performance dependent on recording materials, development of high density recording materials, and the evaluation of crystallization induction time using a static tester. Studied in the development of high density recording materials was the formation of microscopic recording marks in a phase shift/surface recording type disk comprising a 4-element (Ag-In-Sb-Te) recording layer and an Ag reflection layer. In fiscal 2000, an attempt was made at the 0.07 {mu}m level. (NEDO)

  11. FY 1991 Report on the results of the research and development of photo-reactive materials; 1991 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This project is aimed at establishment of the basic technologies for photo-reactive materials capable of, e.g., superhigh-density, superhigh-resolution display using photo-functions to control structures and associated conditions of the molecules. More concretely, the efforts are directed to realization of the technologies for multiplexing, sensitivity-response and material stability, applicable to superhigh-density recording by photochromic and photo-chemical burning (PHB) materials. For the photochromic materials, the long-chain alkyl derivatives of photochromic compounds, e.g., spiropyran and fulgide, are formed into thin films by the LB method, in order to develop organic, superhigh-density recording devices by controlling their associated conditions, and controlling of the photochromism reactions in the films is studied. Those studied for the PHB materials include improvement of heat resistance of the materials, development of quinone-based materials and improvement of their degree of multiplexing, and development of porphyrin-based materials and of technologies for structuring them. The comprehensive survey/research activities include extraction of the problems involved in the themes mainly related to the committee activities, and related technologies. (NEDO)

  12. FY 1985-1992 summarized report on the R and D of photoreactive materials; 1985 nendo kara 1992 nendo hikari hanno zairyo kenkyu kaihatsu sokatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-01

    For the purpose of establishing the basement technology relating to photoreactive materials which make remarkably higher density and larger capacity of the information recording possible, the following were made for photochromic materials and PHB materials: elucidation of the photoreaction mechanism, development of materials, development of material processing/structure technology and development of evaluation technology. The target is to establish the technology of the multiplex recording which is applicable to the super-high density recording in relation to PHB materials/organic photochromic materials which have potentiality of photon-mode recording. PHB materials were developed which have potentiality of 600 wavelength multiple recording and 5 electric field multiple recording in 4.2K and 9 wavelength multiple recording in 77K. Photochromic materials were developed which have high sensitivity and preservation stability and have potentiality of 10 wavelength multiple recording at room temperature. A new photo-recording method was found out by which the orientation of liquid crystal is photo-controlled and potentiality of the multiple polarization was shown. Moreover, the fabrication was successfully made of PHB materials and photochromic materials which make non-destructive readout operation of more than 10{sup 4} times possible. (NEDO)

  13. FY 1989 report on the results of the next generation industrial basement technology R and D project - R and D of photo-reactive materials. Comprehensive investigational research on photo-reactive materials; 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. Hikari hanno zairyo sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    As to photochromic materials and photochemical hole burning (PHB) materials, for the purpose of smoothly/efficiently promoting the R and D, the common basic technology was comprehensively surveyed as well as survey/study of the related technology development in Japan and abroad. In FY 1889, a joint committee was held, and a meeting was held of lectures given by lecturers from outside on the following: reversible response LB multilayered film and 2D optical switching element, photochemical HB and solid polymer, photovoltaic excitation dynamics of polymer solid, wavelength variable/semiconducting laser, optical memory, etc. A meeting for study/discussion on the details was also held. Items for the meeting were as follows: optical orientation control of nematic liquid crystal by photochromic surface, design of photochromic molecules, molecular movement and photo-reactivity in molecular aggregation system matrices, PHB spectra and mesoscopic structure control, continuous HB using semiconducting laser and sub-picosecond photon echo, quinone system derivative PHB in polymer matrices, etc. (NEDO)

  14. Fiscal 1992 R and D project for next generation infrastructure technology. Report on results of R and D on photo-reactive material; 1992 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    R and D was conducted with the purpose of establishing fundamental technologies concerning photo-reactive materials, which control molecular structures or polymerization through light beam behavior and which can be used for ultra-high density optical recording, high resolution display, optical switch, etc., with the fiscal 1992 results summarized. In the studies on photochromic materials, investigation was carried out on the possibility of 10 multiple recording and the fundamental features of aggregate forming photochromic compounds. In the studies on high temperature of photochemical hole burning (PHB) materials, a material was synthesized using ionic porphyrin derivatives as guest material and deuterated polyvinyl alcohol (PVA) and the like as host, with the evaluation made on the performance of multiple hole formation and storage. In addition, comparisons were made for example on the thermal properties of the PHB materials among the participating enterprises mutually. In the development of chinone PHB materials and research on the improvement of the multiplicity, as this being the final year, researches were done on such subjects as integration of element technologies, material evaluation technology and PHB-related studies, correlatively as the work of the final year. Research results were also reported on the development and systematizing technology of porphyrin-based PHB materials. (NEDO)

  15. Leading research report for fiscal 1998 on the research on photofunctional materials for processing 2-dimensional data; 1998 nendo nijigen joho shoriyo hikari kino zairyo ni kansuru chosa kenkyu sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches are conducted for the development of photofunctional materials, which will enable the utilization of such features of light as high speed, planar transmission, and space coupling, for the real-time processing of large-volume 2-dimensional image data etc. The researches cover the 'spatial light modulation material' and 'dynamic holographic memory material' which will be the key materials in the high-speed 2-dimensional data processing, and the 'optical waveguide material.' The 'spatial light modulation material' is a material that temporarily memorizes optical data for causing interference between images by use of light, the 'dynamic holographic memory material' is a material that memorizes phasal data of light and records and writes by use of light the large-volume data necessary for moving picture processing, and the 'optical waveguide material' is a material that transmits multi-dimensional picture data on the real-time basis. Researches are also conducted on the status of research and development of technologies involving novel photofunctional materials, the control of the structure of their electrode/molecule boundary, the creation of ultrastructural materials by molecular arrangement control, etc. (NEDO)

  16. Fiscal 1998 R and D report on femtosecond technology (ultra-short pulse optoelectronics technology); 1998 nendo femuto byo technology no kenkyu kaihatsu (chotan pulse hikari electronics gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report reports the result of the fiscal 1998 R and D on femtosecond technology supported by NEDO. For creation of industrial basic technologies supporting the advanced information society in the 21st century, ultra-high speed electronics technology including new functions beyond the speed limit of conventional electronics technologies is indispensable. From such viewpoint, this R and D aims at establishment of the basic technology necessary for ultra- high speed electronics technology through R and D of technology controlling conditions of beams and electrons in a femtosecond (10{sup -15}-10{sup -12} seconds) region. In fiscal 1998, this project first succeeded in fabrication of a prototype pulse compressor by using semiconductors, and developed a new pulse compressing method by using fibers to generate ultra-short pulse of 38fs. By developing new materials for intersubband transition where ultra-high speed responses can be expected, optical absorption by intersubband transition was first confirmed at optical communication wavelength. The main result for every theme is reported and explained. (NEDO)

  17. FY 1993 Report on the industrial science and technology research and development project results. Research and development of non-linear photoelectronic materials; 1993 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-11-01

    Described herein are the results of the industrial science and technology research and development project for nonlinear optoelectronic materials. The more functional chiral and pi-conjugated compounds are investigated as the organic, low-molecular-weight materials. The technologies for the orientation-controlled crystal growth are continuously investigated. Polyacetylene is investigated as the conjugated pi-electron system. The glass-dispersed systems, prepared by the sol-gel, superlow-melting glass and super-cooling methods, are investigated. In order to elucidate the relationship between the organic superlattice and properties (e.g., photoelectronic properties), the intramolecular interactions under the superlattice conditions are estimated by the theoretical chemical calculations, and the optimum structures deduced from the measured properties are proposed. The thin, composite films of fine metallic particles and glass are prepared by the multi-dimensional sputtering, to explore the constituent materials suitable for the three-dimensional superstructures, and their properties are analyzed. The thin semiconductor films of superlattices are prepared by the molecular beam epitaxy method, to investigate the optimization of the structures and compositions. The basic aspects of the three-dimensional superstructures, prepared by the superfine machining, are investigated. The results of the comprehensive investigations and researches are also described. (NEDO)

  18. FY 2000 report on the results of the R and D of femtosecond technology. Development of the ultra-short pulse optoelectronic technology; 2000 nendo femto byo technology no kenkyu kaihatsu seika hokokusho. Chotan pulse hikari electronics gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project aims at creating new industrial basement technology which supports the highly information-oriented society in the 21st century, conducts the R and D of technology to control the state of light and electron in the femtosecond time domain (10{sup -15} - 10{sup -12} sec), and establishes the basement technology which exceeds the speed limit of the conventional electronics technology and also includes new functionality. Especially, it aims at establishing the basement technology of the ultra-high speed optoelectronics which are absolutely necessary for construction of the Tb/s class ultra-high speed/large capacity information communication infrastructure. The results obtained in this fiscal year were as follows: successful transmission of 144km of 600fs optical pulse, successful experiment of 4-chain pulse DEMUX equivalent to 1Tb/s by ultra-high speed intersubband transition optical switch of Sb-base material combination quantum well, realization of 2-bit coding/decoding in the spectral region, realization of serial-parallel conversion motion of optical pulse equivalent to 1Tb/s using squarylium J aggregate thin films, realization of subpico second optical pulse 20nm wavelength conversion by DFB laser structure, etc. (NEDO)

  19. Fiscal 1975 Sunshine Project research report. Research on hydrogen production technology mainly by photo- semiconductor; 1975 nendo hikari handotai wo shutai to suru suiso seizo gijutsu no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-05-28

    In fiscal 1975, to study the possibility of photochemical decomposition as new hydrogen production technique based on the research result in the preceding fiscal year, study was made on some materials useful as electrode for photocells among various semiconducting materials with large solar photo-electromotive force. Study was made on the kind and combination of electrode materials, and electrolyte composition for photocells through measurement of photocell characteristics by various combinations of semiconductor electrodes. As for the impact of light sources, study was made on the photosensitization phenomenon by xenon light, solar light and xenon lights with various spectral profiles through specific filters, and the relation between a light intensity and hydrogen efficiency. As useful semiconductor photocell electrode systems, combinations of n-type GaP or n- type GaAs and p-type GaP or p-type GaAs were most efficient. As preventive technique of semiconductor electrodes from dissolution, coating technique of various materials showed insufficient results. (NEDO)

  20. Collection of outlines of Sunshine Program achievement reports for fiscal 1988. Solar energy (Light utilizing technology and heat utilizing technology); 1988 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-04-01

    Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the experiment, refining, and verification of low-cost silicon; experiment, fabrication, and verification of solar panels; research on the practical application of high-efficiency crystal-based solar cells; research and development of amorphous solar cells; research and development of solar cell evaluation systems; development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and development of photothermal hybrid type photovoltaic power systems. Collected concerning heat-utilizing technologies are the research and development of solar thermal electric power generation systems; research and development of solar air-conditioners and hot water supply systems; and development of practical application technologies for industrial solar systems. Collected also are international cooperative projects on solar energy technologies. (NEDO)

  1. Collection of outlines of Sunshine Program achievement reports for fiscal 1989. Solar energy (Light utilizing technology and heat utilizing technology); 1989 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-04-01

    Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the research on the practical application of new-type solar cells; research on the practical application of amorphous solar cells; research and development of solar cell evaluation systems; research and development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and research and development of photothermal hybrid photovoltaic power systems. Collected concerning heat application technologies are the research and development of solar thermal energy systems; development of practical application technologies for solar systems for industrial use etc.; and cooperative projects between Japan and Australia etc. on solar energy technologies. (NEDO)

  2. Report on evaluation of research and development of light-aided instrumentation/control systems. Abstract; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Gaiyohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-08-01

    This research and development project is aimed at commercialization of the light-aided instrumentation technology systems which safely, stably measure, transmit and control process information including image information, e.g., temperature, flow rates and components at large plants in industrial complexes, in the severe atmospheres in the presence of, e.g., electromagnetic induction and combustible gases. These optical systems need development of light transmitting/receiving devices, various optical devices that constitute the network nodes, and various types of sensors of improved functions and reliability, in addition to development of the techniques required for transmitting large quantities of information on a large scale. This project has attempted to systematically make break-through in the individual elementary techniques, in particular those in the widely diversified technological areas for the advanced devices, and thereby to expand the instrumentation/control technology frontiers. The results of studies on gallium/arsenic crystals, which are prerequisite for photoelectronic integrated circuits as the bases for the light application technology, and processes for producing thereof are highly rated worldwide. It is planned to effectively utilize the total system, constructed at then Nippon Mining's Mizushima Refinery, and thereby to establish the effective instrumentation techniques for commercial plants and to promote commercialization of these results. (NEDO)

  3. FY 1999 report on the results of the R and D of femtosecond technology. Development of ultra-short pulse optoelectronics technology; 1999 nendo femutobyo technology no kenkyu kaihatsu seika hokokusho. Chotan pulse hikari electronics gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the FY 1999 results of the R and D of femtosecond technology. For the purpose of creating new industrial basement technology which supports the highly information-oriented society in the 21st century, the ultra-high speed electronics technology is indispensable which is beyond speed limits of the existing electronics technology and has new functionality. The ultra-high speed electronics basement technology is established through the R and D of the technology to control the state of light and electronics in the femtosecond time domain (10{sup -15} - 10{sup -12} second). Themes of the R and D are technology to generate/transmit femtosecond optical pulse, technology for control/distribution, and ultra-short pulse optoelectronics common basement technology. In FY 1999, a lot of results were obtained in the following: generation of the pulse train highly repeated at 500GHz in semiconductor laser; 139km transmission of 250fs optical pulse; switching movement at ultra-high speed of 150fs-1.2ps in transition among subbands of GaN base and Sb base materials; DEMUXA movement toward 160-10Gb/s in Mach-Zehnder type optical switch. (NEDO)

  4. 1998 Annual Study Report. Standardization for securing interoperability between optical disk systems; 1998 nendo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This R and D program is aimed at securing interoperability between optical disk systems, based on the logical formats, to propose the draft international standards. For the volume/file structures proposed by ISO/IEC 13346, the universal disk format (UDF) proposed by the Optical Storage Technology Association (OSTA) is taken as the target file system, to improve the conformance test environments and develop the standards for advanced interoperability. The 1998 R and D themes include development of the UDF conformance testing tools for avoiding the interoperability-related problems involved in the UDF, which are actually observed, and investigations on the UAF specifications and preparation of the UAF-related standard evaluation systems for preparation of the draft standards for the Universal Accessible Filesystem (UAF), planned to be conducted in and after the next fiscal year, which allows, e.g., network seamless application of a variety of the future optical disks. (NEDO)

  5. FY 1992 Report on the results of the research and development project for the industrial base technologies of the next generation. Research and development of nonlinear optoelectronic materials; 1992 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Described herein are the FY 1992 results of the research and development project for the optoelectronic materials. The FY 1992 is the last year for the phase-I project of the basic plan, and the results are evaluated mainly viewed from extent of attainment of the interim targets. For the organic materials, the highly unique chiral nonlinear compounds are further developed, and direction for the investigations of the conjugated low-molecular-weight compounds is established. The excellent high-molecular-weight films are developed. For the dispersed materials, those developed include CuCl-dispersed glass, CdTe laminated glass developed by the laser evaporation method, glass dispersed with semiconductors at high concentrations, and dispersed materials with high-molecular-weight materials as the matrices. For the material development, those technologies investigated are orientation controlling of the crystals for thin organic films, and development of superlattices. A total of 9 research themes are recommissioned to 9 enterprises. They include organic, low-molecular-weight materials, growth of orientation-controlled crystals, films of high-molecular-weight organic conjugated compounds, glass-dispersed materials (prepared by the vapor-phase, impregnation of porous glass, sol-gel, superlow-melting glass and super-cooling methods), organic dispersed materials, development of the organic superlattices, and development of the three-dimensional superstructures. (NEDO)

  6. FY 1990 Report on the results of the research and development project for the industrial base technologies of the next generation. Research and development of nonlinear optoelectronic materials; 1990 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Described herein are the FY 1990 results of the research and development project for the optoelectronic materials, implemented to cope with the highly information-oriented societies. The FY 1990 is the second year for the phase-I project of the basic plan, and the R and D efforts are directed to elucidation of the mechanisms involved in the nonlinear phenomena, exploration and designs of various materials, and investigations of the technologies for, e.g., the material synthesis and evaluation. The themes to be investigated by the long-term project include exploration and preparation of the superfine particles and base materials for the organic materials; and crystal growth, dispersion of the fine particles and development of the superlattices for development of the materials. The comprehensive investigation and research program investigates the trends of the related technologies, both domestic and foreign. A total of 9 research themes are recommissioned to 9 enterprises. They include organic, low-molecular-weight materials, growth of orientation-controlled crystals, films of high-molecular-weight organic conjugated compounds, glass-dispersed materials (prepared by the vapor-phase, impregnation of porous glass, sol-gel, superlow-melting glass and super-cooling methods), organic dispersed materials, development of the organic superlattices, and development of the three-dimensional superstructures. (NEDO)

  7. Report on the achievements in fiscal 1999 of research and development of fusion zones. Volume 1. Next generation light beam foundation technology; 1999 nendo yugo ryoiki kenkyu kaihatsu seika hokokusho. 1. Jisedai hikari kiban gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop a high-speed high-density light beam recording technology by application of proximity field light, researches were performed on a flat opening type proximity field head, a recording and replaying system for the super lens, the materials thereof, proximity field optical elements, and the application to lithography. As a result of the researches, development was made on a promising light scattering super lens, whose noise level is low and the carrier is stable. Deterioration of the replay signals in association with repeated read-out is caused by instability of the recording film. It was verified, however, that more than 60,000 read-outs are possible by adding oxygen into the recording film material to raise the crystallization temperature. Application of the super lens to organic thin film recording utilizing thermo-chromism was verified to be effective. In discussing the application of the super lens to lithography, a possibility was confirmed to expose a resist film through the super lens structure. A simulation program for the proximity field light was developed, and new findings were acquired. (NEDO)

  8. Report on results 1998. Research and development on fusion area. Part 1 (next generation optical substrate technology); 1998 nendo seika hokokusho. Yugo ryoiki kenkyu kaihatsu daiichi bunsatsu (jisedai hikari kiban gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Emphasis was placed on the research on a planar apertured near-field head and a super-RENS (super-resolution near-field structure) method, as a near-field application element for replacing protruding probes, which has a number of difficult points in developing near-field recording into a practical system, and as a recording and reproducing method. The super-RENS method, as a result of the examination, has become capable of recording/detecting a mark of the minimum 60nm diameter, by the near-field, under conditions such as the most advanced optical disk size and the number of revolution of the disk. This means that a high density recording is possible which is at least 40 times as dense as a DVD (digital versatile disk). It was confirmed by an experiment that the high density was possible in the track pitch direction by the super-RENS method. As a result of the examination on the behavior of the near-field in the super-RENS disk, it revealed that signal detection by the transmitted light which had not been tried before was effective for the improvement of the performance. The smallest detectable mark size was 80nm, in which case CNR (carrier to noise ratio) was 6.4dB. These values are approximately the same level as in the signal detection by reflected light, and are insufficient to verify the superiority. (NEDO)

  9. FY 1997 research and development of fusion domains. Part 3. Studies on next generation optical substrate technologies; 1997 nendo seika hokokusho (yugo ryoiki kenkyu kaihatsu). 3. Jisedai hikari kiban gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    With an objective of realizing super large capacity recording technologies largely exceeding the current limits of optical recording and magnetic recording, studies were conducted on application of near-field optics. In the study on recording by using near-field light, it was verified that a mark with approximately the same size as an aperture diameter can be formed on a phase change recording film when a fiber probe with an aperture diameter of about 200 nm is used. However, it was found that the recording using this system takes excessive amount of time. When laser light collected on an objective lens was irradiated pulse-wise, a mark with a minimum width of about 20 nm was observed with high contrast. This will mean that a record with recording density of one terabit/in {sup 2} can be read out. Other studies performed include those on evaluation of effects of polarized light and surface shape on near-field read-out, simulation, mechanism of crystallization in a phase change recording film, recording and playback with ultra-high resolution by using a conformable near-field aperture, fabrication of a flat aperture type near-field light probe array, and the evaluation thereon. 22 refs., 27 figs.

  10. Fiscal 1999 research result report. Research on improvement of boiling heat transfer characteristics by photocatalyst wall; 1999 nendo hikari shokubai hekimen ni yoru futto netsu dentatsu tokusei kaizen ni kansuru kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research was made on improvement of the wettability and boiling heat transfer characteristics of a photocatalyst wall. Measurement experiment of the wettability was made for anatase type titan oxide-coated Al, SUS and Pb plates, rutil type titan oxide-flame coated SUS plate, raw plate, and oxide-plasma coated titan plate. In the ground experiment, the contact angles of distilled water and oil on specimen surfaces were measured. In the microgravity experiment, falling droplet images were recorded by using the facility of Japan Microgravity Center (JAMIC). For obtaining the effect of radioactive emission, UV irradiation, {gamma} ray and neutron beam irradiation by nuclear reactor, and {gamma} ray irradiation by Co-60 were carried out. As the experiment result, the rutil type titan oxide-flame coated SUS plate, nonconductor-coated titan plate, and zircaloy plate showed large improvement of the wettability by {gamma} ray irradiation with Co-60. It was also confirmed that in particular, titan shows the large effect of radioactive emission, and the wettability deteriorates rapidly after {gamma} ray irradiation. (NEDO)

  11. Evaluation report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; Hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The results achieved in fiscal 1992-1995 under the above-named project are stated. In the development of photocatalytic materials, a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus is developed. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is fabricated, which achieves a level higher than the denitration goal of 70%. Although the sheet in a 500-hour accelerated exposure test undergoes a hardening phenomenon in which elasticity decreases and tensile strength increases, yet degradation is hardly detected. Although a slight reduction is detected in denitration efficiency, yet it does not affect its practical application, and thus the durability goal is achieved. In the development of an energy conservation type air cleaning apparatus usable in underground parking areas or motorway tunnels, an apparatus capable of treating air at a rate of 2,000m{sup 3}/hour is fabricated, and this achieves a denitration level of not less than 80% in a field test (in the absence of rainfall). For denitration in the presence of rainfall, the apparatus is combined with an equimolar adsorption system, and a system capable of 80% denitration is proposed on the basis of data actually measured for each of the two. A conceptual design for a service model comprising a photodenitration and equimolar adsorption systems is evaluated, and it is found that it occupies less space than the existing models. (NEDO)

  12. Fiscal 2000 achievement report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; 2000 nendo hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The research aims to develop materials and apparatuses for the purification of atmosphere using titanium dioxide that exhibits a powerful oxidizing capability when irradiated with light. A study is conducted to find out an optimum composition for a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is found to show high denitration efficiency, and this achieves the denitration efficiency goal. As for sheet thickness, 0.75mm is found to be enough. The sheet experiences some hardening in an accelerated exposure test, but does not change much in a surface gloss test or a chalking test. Although a slight reduction is observed in denitration efficiency, yet the durability goal is achieved. In the effort to develop an energy conservation type air cleaning apparatus, field tests and experiments are repeatedly conducted. As for photodenitration in the cleaning apparatus, the number of photodenitration stages and the magnitude of equimolar adsorption area necessary for achieving an 80% denitration rate is calculated from the relations of the NOx concentration profile and the denitration rate in the equimolar adsorption module to (gas flow rate/module surface), and the result shows that the initially intended goal is achieved. (NEDO)

  13. FY 1974 report on the results of the Sunshine Project. Study of the hydrogen production technology mainly using photoconductor; 1974 nendo hikari handotai wo shutai to suru suiso seizo gijutsu no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-28

    Among semiconductor materials which absorb solar light and produce great photoelectromotive force, materials usable to the electrode of photoelectric cell were sought, the photoelectrode reaction of various electrode materials was investigated, and the photosensitization phenomenon in the solar light region was studied. As to electrode materials, semiconductor materials were sought which have a characteristic of band gap of 1-3eV, and the photosensitization polarization characteristic of a part of the semiconductor materials was measured. Concerning photoelectric cells, the photoelectric cell characteristic was measured by the combination of semiconductor electrode, for the study of the structure of photoelectric cell such as kinds, combination, etc. of electrode materials. As electrode materials, various semiconductors were acquired such as TiO{sub 2}, CdS, GaP, GaAs, Si, Ge, etc., and the electrochemical base photoelectrode characteristic under light irradiation was measured. It was confirmed that GaP and GaAs have good photosensitization polarization characteristics. As the result of the measurement of photoelectric cell characteristics, n-type GaP and n-type GaAs showed good characteristics to anode, and p-type GaP and p-type GaAs to cathode. It was confirmed that there is a possibility of hydrogen production in the solar light wavelength region by the measurement of photoelectric cell characteristics of xenon light and the filter penetration light of xenon light. (NEDO)

  14. Research and development project in fiscal 1989 for fundamental technologies for next generation industries. Achievement report on research and development on photoreactive materials (Research on designing and organizing technology for PHB materials); 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. PHB zairyo no sekkei to soshikika gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective of putting into practical use the wavelength multiplex recording system applied with the PHB phenomenon, research and development has been performed on material systems making high quality hole production possible at high sensitivity and high density. This paper summarizes the achievements in fiscal 1989. In the discussion of PHB materials, measurements were performed on the triple state of zinc, magnesium, copper and iron complexes of tetra-phenyl porphin and the triple state spectra by using the flash decomposition method in order to develop new photo-gate type material systems. Correlation was discovered between the free energy change in the reaction and the PHB reactivity from the result of the experiments, whereas important findings were obtained for designing the photo-gate type PHB material systems. In the discussion of the wavelength multiplex recording, an optical system was designed and fabricated to perform scanning and detection on sample surface by using laser beam squeezed to a diameter of 100 {mu} m. Discussions were given on the wavelength multiplex recording, position multiplex recording, and high-speed recording using this optical system. As a result, position multiplex holes were produced successfully by using the laser beam squeezed to a diameter of 100 {mu} m on four different positions on the sample surface, when the tetra phenylporphin derivative was used. (NEDO)

  15. FY 1998 report on the results of R and D projects by local consortiums for immediate effects. Development of titanium dioxide thin film photocatalysts sensitive to visible light and their applications to cleaning systems; 1998 nendo kashiko kasseina sanka chintan hikari shokubai usumaku no kaihatsu to sono system oyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D project has been implemented for developing the thin film-making process techniques which can increase areas of titanium oxide (TiO{sub 2}) photocatalysts sensitive to visible light and their mass production. The fundamental investigations are directed to elucidation of the mechanisms involved in manifestation of activity in visible light of the visible light-sensitive thin film doped with the Cr, V or other ions. The sputtering involving no ion implantation is devised for producing the thin films, to realize the highest visible light sensitivity recorded for the thin TiO{sub 2} film. The sputtering process is investigated in detail for the film-making conditions, e.g., Ar pressure, effects of coexisting O{sub 2} gas, and power gap. The conditions under which the thin film serviceable under commercial conditions can be produced are not established yet, but it is confirmed that the coating film shows superhydrophilicity and photocatalytic activity for, e.g., sterilization, when irradiated with ultraviolet ray. The method has been established for evaluating deodorizing and contamination-preventive functions of the thin films in ultraviolet and visible rays. The project has also confirmed applicability of the techniques to the commercial products, and established the self-cleanable catalyst by combining the oxide catalytic function with the photocatalytic function. (NEDO)

  16. FY 1999 project on the development of new industry support type international standards. Standardization of methods to test/evaluate plastic optical fiber; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Plastic hikari fiber no shiken hyoka hoho no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The experimental research was conducted with the aim of developing test/evaluation methods of plastic optical fiber (POF) and proposing a draft on the standards to IEC, and the FY 1999 results were outlined. In the study of the band measuring method, the equipment designed was compared/verified in the pulse method with the frequency sweep method equipment for quartz base optical fiber use to confirm the accordance. Effects were further studied of experimental conditions including exciting conditions. Also about the frequency sweep method, the same verification was made to see the accordance with POF measured values in the pulse method. In the analysis by theoretical calculation, obtained were the results by which the experimental results can almost be explained. In the experiment on the optical transmission, the bit-error-rate was measured by transmitting digital signals to POF. As a result, it was confirmed that there were close relations between the band width of POF, bit-error-rate and changes in receiving sensitivity. As to the above-mentioned band experimental method, strategy for standardization was studied, and the making of a draft on the standards was started which is to be proposed at the meeting of TC86/SC86/WG1. (NEDO)

  17. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Development of new vacuum ultraviolet area optical materials realizing next generation short wavelength optical lithography; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Jisedai tanhacho hikari lithography wo jitsugensuru shinku shigaiiki kogaku zairyo no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As materials for next generation lithography use optical device using short wavelength light sources such as F{sub 2} and Ar{sub 2}, the development was proceeded with of fluoride monocrystal materials and 12-inch class large/high quality monocrystal production technology. Studies were made in the following five fields: 1) proposal/design of new materials and the heightening of performance: 2) establishment of the large/high quality crystal production method; 3) evaluation of optical properties and elucidation of micro-defect formation mechanism; 4) comprehensive investigational research; 5) study of the evaluation technology by vacuum ultraviolet area pulse light. In 1), for the development of the optimum materials, a lot of materials were tried to be monocrystallized, and the permeability was estimated by measuring the reflectance in the vacuum ultraviolet area. As to LiCaAlF{sub 6}, monocrystal with 1-inch diameter was made by the Bridgman method. In 2), studies were made of conditions for large crystal growth by the pull method, large crystal growth by the Bridgman method, and the structure of production equipment for crystals with larger diameter. (NEDO)

  18. Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

  19. FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

  20. FY 1998 report on the results of the venture promotion type regional consortium- small-/medium-size enterprise creation base type. consortiums. Development of photo-curing containing coating materials for comfortable, healthy indoor environments; 1998 nendo shitsunai kankyo no kaitekisei, kenkosei ni taioshita hikari jugo urushi toryo no kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research and development project is aimed at activation of the urushi industry and creation of the new business by utilizing the natural material by the name of urushi solution as the functional coating material satisfying the various conditions required for the coating solutions of the next generation, e.g., healthy, safety, comfortable and environmentally harmless characteristics. The urushi solution developed by this project is an innovative, creative one, which solves the major problems involved in the conventional solution, i.e., slow curing and causing eruption of the skin, by enzyme-aided polymerization and photopolymerization. The physiological activities of the urushi solution component and antimicrobial effects by the urushi layer, which are considered to be the potential functions of urushi, are also investigated for the project. The urushi-containing UV coating material means an ultraviolet-curable urushi/synthetic resin material, composed of refined urushi, a photopolymerizable acrylate compound and photopolymerization initiator. The refined urushi for the urushi-containing UV coating material can be adjusted for its degree of polymerization, as found by the experimental investigation of the catalyst for accelerating enzyme-aided polymerization, to improve curability. The confirmed physiological activities of the urushi component are accelerated solidification of the blood and manifestation of the anti-HIV function. The coating film of the refined urushi is found to be effective against Bacillus coli and Staphylococcus aureus. (NEDO)

  1. Achievement report on research and development in the Sunshine Project in fiscal 1976. Research and development of water decomposition by using a hybrid cycle composed of thermo-chemistry and photo-chemistry; 1976 nendo netsukagaku oyobi hikari kagaku hybrid cycle ni yoru mizu bunkai no kenkyu kahatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This paper describes water decomposition by using a hybrid cycle composed of thermo-chemistry and photo-chemistry. Ferric sulfate and HI are obtained from ferrous sulfate and iodine via photo-chemical reaction. This is an endothermic reaction of 10.8 kcal. Then, the photo-chemically reacted aqueous solution is electrolysed to separate HI, while Fe{sup 3+} (ferric ion) is reduced and converted into Fe{sup 2+} (ferrous ion). Oxygen is generated at this time. Since mixed potential is made from iron oxidation and reduction potential and iodine potential, the electrolytic efficiency is greatly influenced by electrode materials. Ideally, an electrode material that causes only the reduction of Fe{sup 3+}, but not other reactions is preferable. The HI is decomposed into hydrogen and iodine by electrolysis. Research is continuing to acquire hydrogen from HI thermo-chemically. Endothermic reaction heat of 7 to 8 kcal has been obtained in photo-chemical reaction, the heat quantity being close to the theoretical value of 10.8. A result close to the theoretical value may be expected if the electrode material problem is solved. The basic research will be continued for a high possibility of linking the research to a pilot plant in the future. (NEDO)

  2. Report on achievements in fiscal 1984 on research and development commissioned from Sunshine Project. Research and development of water decomposition using the mixed cycle of thermo-chemistry, photo-chemistry, and electro-chemistry; 1984 nendo netsu kagaku, hikari kagaku, denki kagaku konsei cycle ni yoru suibunkai no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    Researches have been performed on water decomposition by multiplex utilization of solar beam, and the achievements in fiscal 1984 were reported. In fiscal 1984, activity coefficients for iron ions and iodide ions having been discussed by the previous fiscal year were derived, and free energy variation amount and accumulated energy amount generated as a result of photo-chemical reactions were derived. Values derived in the experiment were low, which are the values at room temperatures, and higher values are expected under elevated temperatures. In an experiment using a beam irradiation electrolytic tank, investigations were made on thermo-chemical isolation and electrolytic isolation of HI. Since HI is strongly acidic, it does not get liberated unless phosphoric acid concentration and temperature are increased, which is a condition opposing to easiness of the photo-chemical reaction. Therefore, an experiment on HI was performed not only on isolation due to heat, but also isolation by electrolysis, where the intended result was obtained. The mixed system of a photo-chemical system and an electrolytic system requires a system configuration that considers dynamic matching conditions, for which a system to perform measurements simultaneously on a large number of kinds was found effective. (NEDO)

  3. Achievement report for fiscal 1982 on Sunshine Program-entrusted research and development. Research and development of electrolysis of water using thermochemical/photochemical/electrochemical mixed cycle; 1982 nendo netsu kagaku, hikari kagaku, denki kagaku konsei cycle ni yoru suibunkai no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    The research and development aims to increase the yield of light energy conversion in a photochemical reaction and thereby to increase the efficiency of the reaction of electrolysis of water. In the research, the electrochemical properties of Fe{sup 3+}/Fe{sup 2+} and I{sub 3}{sup -}/I{sup -} systems in a phosphoric acid solution are examined. As for the behavior of iodine ions I and I{sub 3}, their capacity coefficient rises with a rise in temperature at any phosphoric acid concentration level. Furthermore, more water molecules are disengaged from hydrated iodine ions with an increase in the concentration of phosphoric acid, and the now naked iodine ions are higher in activity coefficient. The behavior of iron ions in phosphoric acid is observed by use of a rotating electrode. Although the activity coefficient ratio of iron ions and iodine ions exerts a great influence in the process of conversion from light energy to chemical energy, the outcome of experiment indicates that the ratio is low for both iron- and iodine-based systems. It is consequently concluded that an energy conversion rate of approximately 10kcal/mol is expected from a photochemical reaction as in the case of hydrated systems. (NEDO)

  4. FY 1985 report on research and development project commissioned by the Sunshine Project. Research and development of electrolysis of water by combined thermochemical, photochemical and electrochemical cycles; 1985 nendo netsu kagaku, hikari kagaku, denki kagaku konsei cycle ni yoru mizu bunkai no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    Reported herein are the FY 1985 research results on the combined water electrolysis cycles by effective utilization of sunlight. The tests for determining activity coefficient of an iron/iodine system is continued from the previous year, and the results are used to find the optimum conditions under which the photochemical and electrolysis reactions are effected simultaneously in a light-irradiated electrolysis tank. It is found that a photochemical reaction efficiency of approximately 0.3% is obtained at 5 W/cm{sup 2} as light intensity and 25 degrees C. For electrolysis of water by the multi-stage hybrid cycles, it is necessary for the reaction in each stage to proceed to almost the same extent so that it gives a just enough quantity of product for the subsequent stage. The data obtained are analyzed comprehensively, while taking the system matching conditions into consideration. The system for simultaneously measure two or more parameters, developed in the previous year, is equipped with a high-level language compiler of high effective speed, to simultaneously measure these parameters at shorter intervals. (NEDO)

  5. Achievement report for fiscal 1983 on Sunshine Program-entrusted research and development. Research and development of water-splitting systems using thermochemical, photochemical, and electrochemical mixed cycle; 1983 nendo netsu kagaku, hikari kagaku, denki kagaku konsei cycle ni yoru suibunkai no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    The report covers the outcome of a basic study of the splitting of water using photochemical reaction. The behavior of iron ions and iodine ions is important in the photochemical reaction in the phosphoric acid and in the energy exchange that follows, and the characteristics of iodine ions are investigated in detail. Since the response of a commercially available iodine ion electrode is slow in a strong phosphoric acid solution, a silver/silver iodide electrode is experimentally built, and is used in the investigation of the iodine ion activity coefficient. In the investigation, it is indicated that more energy is accumulated when temperature or concentration is higher. In the case where sunlight is used as the light source for photochemical reaction, it is necessary to perform optimal control in compliance with fluctuation in sunlight intensity. In the study, fluctuation in sunlight intensity is assumed to be composed of step waves, pulse waves, and sinusoidal waves, and a result of digital simulation is obtained by using a modelling method for control. For the convenience of computation, the number of cell division is set at approximately five, when the solution flow responsiveness and energy conversion utilization factor are found to be excellent. (NEDO)

  6. Achievement report on research and development in the Sunshine Project in fiscal 1978. Research and development of water decomposition by using the thermo, photo and electro-chemistry mixed cycle; 1978 nendo netsukagaku, hikari kagaku, denki kagaku konsei cycle ni yoru suibunkai no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    This paper describes research achievements in fiscal 1978 on water decomposition by using the thermo, photo and electro-chemistry mixed cycle. Fundamental experiments were carried out in a photo-chemical and electrolytic reaction tank to electrolyse as quickly as possible HI and iron (III) produced by photo-chemical reaction in the iodine-iron (II) system, and separate the products therefrom. The photo-chemical reaction was analyzed by using the spectro-photometry, and the degree of reaction progress was quantified by using the change in absorbance of I{sub 3}{sup -}. Since temperature rise due to sun beam irradiation accelerates reverse reaction, the apparent equilibrium position under the beam irradiation was moved from the product system to the original system as the temperature rises. An expression showing the reaction efficiency was introduced to indicate that beam collection enhances the efficiency. There is no electrolytic electrode material that reduces only iron (III) preferably, and electrolysing the aqueous product solution as it is results in low energy efficiency. In addition, as a result of discussing factors affecting the effect of HI decomposition (to acquire hydrogen) by using a heat diffusion column, it was revealed that maximum separation effect can be derived if the material is fed from the center of the column. Discussions were given also on other factors. (NEDO)

  7. Achievement report on research and development in fiscal 1989 for fundamental technologies for next generation industries. Research and development on photoreactive materials (Research on control of association status of photochromic compounds); 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. Photochromic kagobutsu no kaigo jotai seigyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective of creating ultra-high density organic photo recording elements for photon mode recording and rewritable wavelength multiplex recording by utilizing control of association status of photochromic compound, research and development has been performed. This paper summarizes the achievements in fiscal 1989. In developing the materials, verification was made on effectiveness of the newly structured positive polarity model. The method was used to attempt synthesis of four kinds of new spiropyrane, among which it was discovered that BSP1822 forms J-association complex in the long wavelength region. In the thin film forming technology, the J-association complex of BSP1822 was stabilized successfully in the film mixed with bi-molecular film forming material. In order to develop a technology to form dry photochromic thin films, an organic molecular beam epitaxial device and a thin film structure analyzer were introduced. In the elucidation and research on fundamental properties, discussions were given on properties of the SP1822LB film revealed by the steady-state light and laser pulse light. Furthermore, the molecular orientation of the SP1801 on the air-water interface was investigated, and molecular models on the air-water interface were considered. (NEDO)

  8. Fiscal 1999 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of hypersensitive photocatalyst using oxide semiconductor thin film having nanostructure; 1999 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Nano bisai kozo wo yusuru sankabutsu handotai usumaku ni yoru chokokando hikari shokubai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The thin film structure of photocatalytic titanium oxide, capable of efficiently decomposing hazardous pollutants or the like, is refined to have a nanometric scale structure for a larger specific surface for the development of a photocatalytic thin film or powder film and for the development of decomposition capable air cleaner using a thus developed photocatalytic film. Described in this report are the results of a study conducted to elucidate the fabrication conditions, nanostructures, and photocatalytic features of titanium oxide thin films formed by spray thermolysis, RF (radio frequency) sputtering, reactive sputtering, and sol-gel process, a study of hazardous pollutant decomposing capability and nanostructure, the establishment of fabrication technologies, and the construction of a prototype air cleaner with the results of the said studies applied thereto. Among the various fabrication methods, the technology involving a hypersensitive thin film photocatalyst was established by combining the reactive sputtering method and the sol-gel method. It was found that the formation of prismatic crystals in the sol-gel method was the most important in achieving high performance in the hypersensitive thin film photocatalyst. (NEDO)

  9. Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of methods for testing and evaluating plastic optical fiber; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Plastic hikari fiber no shiken hoho no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Studies were made about methods for testing and evaluating plastic optical fiber (POF) for the purpose of submitting a proposition to IEC (International Electrotechnical Commission) for the methods to be internationally standardized. In this fiscal year, tests and analyses were conducted relative to the effects of the light source emission area size, wavelength, and axial displacement. Next, underfilled launch was studied from a practical viewpoint, and a method using a mode filter was proposed. Finally, round robin tests were conducted for each of the companies using overfilled launch and underfilled launch, and the reproducibility of measured values was grasped. In this fiscal year, a new study added, which involved a method for measuring structural parameters. Though POF was below standard as an object of IEC's gray scale method, yet it was found, thanks to the recently developed CCD (charge coupled device) cameras, that the method might also be applicable to POF. A groundwork plan was drafted on band test methods including the overfilled launch method toward international standardization. (NEDO)

  10. Fiscal 1999 achievement report. Venture seed pickup type international cooperative research project (Development of ultrahigh-speed terabyte optical disk storage device); 1999 nendo venture seeds hakkutsugata kokusai kyodo kenkyu jigyo seika hokokusho - venture seeds No.7. Chokosoku terabyte hikari disk kioku sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to submit a concrete, industrialization-capable proposition for a huge-volume high-rate data storage device to be connected directly to the optical fiber communication network. The terabyte optical disk storage device is based on the patented technologies owned by some organizations participating in the project, and embodies a 1-terabyte memory and a 1-Gbps data transfer rate in a CD-size disk with CD/DVD compatibility not affected. The road to a novel, huge-volume, ultrahigh-speed data storage device was open when the basic principle of collinear-polarization digital volume holography was successfully confirmed. A new optical disk medium was fabricated for recording digital volume holograms, and a success was attained in retrieving records on a terabyte optical disk evaluation system. A novel spatial light modulator was successfully fabricated using the magnetooptic effect. This will enable improvement on transfer rates in digital volume hologram retrieval devices and introduction of such devices into optical communication in the field of information technology. (NEDO)

  11. FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

  12. Research and development project in fiscal 1989 for fundamental technologies for next generation industries. Achievement report on research and development on photoreactive materials (Research on enhancement of functional stability of PHB materials); 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. PHB zairyo no kino anteisei kojo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective of establishing the fundamental technologies related to photo reactive materials that can be used for ultra-high density recording, high-resolution indication, and photoswitches by controlling structures and association status of molecules by using actions of light, research and development has been performed. This paper summarizes the achievements in fiscal 1989. In the research of synthesis and evaluation of PHB materials, a possibility was verified to form holes at temperatures higher than the liquid nitrogen temperature on all the materials in which six kinds of ionic porphin derivatives were dispersed into polyvinyl alcohol. Stability of holes in the tetra-alkyl pyridinium porhpn/polymer system was evaluated, the hole half-width was measured accurately by using ring die laser, and the hole forming characteristics were evaluated by means of high-power density and brief laser light irradiation. In search of new guests, a two-photon absorption spectrum measuring instrument was assembled to measure samples having zinc tetra-phenylporphyrin derivative as the guest. In addition, hole formation was discovered in samples having indomethylene based coloring matter as the guest. (NEDO)

  13. Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for enhanced interoperability between optical disk systems; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was carried out for the enhancement of logical format-based interoperability between optical disk systems for the purpose of presenting propositions for international standards. That is, UDF (universal disk format) defined by OSTA (Optical Storage Technology Association) was taken up against the volume/file structure defined by ISO/IEC13346, and efforts were exerted to substantiate environments for its compatibility test and to develop specifications to achieve such enhanced interoperability. In this fiscal year, specifications were drafted for application program interfaces for the UDF-based file system and UDF security augmentation. These would be presented to IEC (International Electrotechnical Commission) and OSTA, respectively. Their Japanese versions were submitted to the Ministry of Economy, Trade and Industry of Japan, for publication as standard-related information. Maintenance of UAF (universal accessible file) system-compliance test tools were accomplished in response to user requirements and to the updating of UDF-compliance test disk specification. (NEDO)

  14. Achievement report on research and development in the Sunshine Project in fiscal 1977. Research and development of water decomposition using mixture cycles composed by thermo-chemistry, photo-chemistry and electrochemistry; 1977 nendo netsukagaku, hikari kagaku, denki kagaku konsei cycle ni yoru suibunkai no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-01

    Discussions are being made on manufacture of hydrogen and oxygen from water decomposition using mixture cycles composed by thermo-chemistry, photo-chemistry and electrochemistry using ferrous sulfate and iodine. Photo-chemical reaction produces Fe(OH)SO{sub 4} and HI, but due to difficulty of isolating Fe(OH)SO{sub 4}, photo-chemical reaction that can obtain the compound as Fe{sub 2}(SO{sub 4}){sub 3} was introduced. A method was introduced that can perform HI isolation simultaneously while performing reaction to reduce Fe{sup 3+} and turn it into Fe{sup 2+} (generating oxygen) by means of electrolysing the liquid after the former reaction. The electrolytic process decomposes HI into hydrogen and iodine (discussions on thermo-chemical decomposition is also continued). Since the photo-chemical reaction can cause reverse reaction, discussions were given on the reaction process in order to suppress the reverse reaction and enhance the conversion efficiency. This paper describes the achievements during fiscal 1977. A quantification method was elucidated on individual iodine components so that it can be used for computerized control (measurement of absorbance of I{sub 3}{sup -}) . An electrolytic tank was discussed that decomposes and isolates photo-chemical reaction products before the reverse reaction occurs. Heat diffusion method was also discussed that isolates hydrogen from HI decomposition products. (NEDO)

  15. Achievement report on research and development in the Sunshine Project in fiscal 1979. Research and development on water decomposition by using mixed cycle of thermo-chemistry, photo-chemistry and electrochemistry; 1979 nendo netsukagaku, hikari kagaku, denki kagaku konsei cycle ni yoru mizu bunkai no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    This paper describes achievements in research and development in the Sunshine Project in fiscal 1979 on water decomposition by using mixed cycle of thermo-chemistry, photo-chemistry and electrochemistry. In research on the light irradiation electrolytic process, with an objective of improving the reaction efficiency, discussions were given by raising light intensity on the irradiated surface as high as 13 times that of the sunlight. The subsequent process is electrolysis of products from photo-chemical reaction, and the product concentration should be high enough to have HI decomposition (hydrogen acquisition) proceed with high efficiency. Experiments were carried out at 0.03 to 0.1M as iodine concentrations (product HI concentration at 3%). A photo-chemical reaction rate of 80% was obtained at light intensity as high as 12 times that of the sunlight, and iodine concentration of 0.07 mM. The efficiency was 15%. Raising temperature causes the reaction rate to decrease, but it can be supplemented by raising the light intensity, where high concentration HI content was obtained. Rate controlling process in the reaction was elucidated from activation energies in the reaction process of each element on the iodine concentrations from 3 to 30 mM used in the photo-chemical reaction. Experiments were performed on HI decomposition (hydrogen acquisition) by using a heat diffusion column. Separation performance in a filled type column was worse than that in an empty type column, which requires future discussions. (NEDO)

  16. Subsurface displacement of the Tachikawa fault; Tachikawa danso no chika shinbu ni okeru danso hen`i

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, K; Kano, N; Kiguchi, T; Tanaka, A [Geological Survey of Japan, Tsukuba (Japan); Sato, H [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1997-10-22

    Seismic exploration using the reflection method was carried out at the central section of the Tachikawa fault located in the western part of the Musashino high plain spreading over Tokyo and Saitama Prefectures. The course of traverse was set on a road running in the east to west direction, which crosses the running direction of the Tachikawa fault in Sunagawa, Tachikawa City by about 65 degrees. The area near the course of traverse is a terraced alluvial fan, with the nature of its surface soil consisted of a gravelly bed of the Quaternary period. In order to identify the fault structure in detail, the focal point interval was set to 5 m, being half of the vibration receiving point interval of 10 m. The CMP was defined at a 2.5-m interval rather than a 5-m interval. The S/N ratio of the derived data was found not good. This is because of scattering of seismic energy into the gravelly bed with a thickness of about 100m in the shallow portion and because of noise from passing vehicles. The data processing was applied with correlation, geometry, static correction, velocity analysis and CMP polymerization to have prepared a preliminary CMP polymerization time cross section. As a result, it was elucidated that the Tachikawa fault forms a bend zone or a crush zone under the ground, and continues down to a great depth at a high angle. 9 refs., 3 figs.

  17. Photoenhanced atomic layer epitaxy. Hikari reiki genshiso epitaxy

    Energy Technology Data Exchange (ETDEWEB)

    Mashita, M.; Kawakyu, Y. (Toshiba corp., Tokyo (Japan))

    1991-10-01

    The growth temperature range was greatly expanded of atomic layer epitaxy (ALE) expected as the growth process of ultra-thin stacks. Ga layers and As layers were formed one after the other on a GaAs substrate in the atmosphere of trimethylgallium (TMG) or AsH{sub 2} supplied alternately, by KrF excimer laser irradiation normal to the substrate. As a result, the growth temperature range was 460-540{degree}C nearly 10 times that of 500 {plus minus} several degrees centigrade in conventional thermal growth method. Based on the experimental result where light absorption of source molecules adsorbed on a substrate surface was larger than that under gaseous phase condition, new adsorbed layer enhancement model was proposed to explain above irradiation effect verifying it by experiments. As this photoenhancement technique is applied to other materials, possible fabrication of new crystal structures as a super lattice with ultra-thin stacks of single atomic layers is expected because of a larger freedom in material combination for hetero-ALE. 11 refs., 7 figs.

  18. Faults survey by 3D reflection seismics; Sanjigen hanshaho jishin tansa ni yoru danso chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, T; Ejiri, T; Yamada, N; Narita, N; Aso, H; Takano, H; Matsumura, M [Dia Consultants Company, Tokyo (Japan)

    1996-10-01

    This paper describes fault survey by 3D seismic reflection exploration. Survey has been conducted mainly at flat land area without pavement not in urban area in Japan. Subsurface structure is complicated with intersecting multiple faults. In this area, a lot of geological investigations have been done prior to the seismic reflection exploration. Fairly certain images of faults have been obtained. However, there were still unknown structures. Survey was conducted at an area of 170m{times}280m in the CDP range. Measurements were carried out by using 100 g of dynamite per seismic generation point combined with 40 Hz velocity geophones. Fixed distribution consisting of lattice points of 12{times}12 was adopted as an observation method. In and around the lattice, a great number of explosions were carried out. The CDP stacking method and the method of migration after stacking were used for the data processing. The 3D structures of six horizons and five faults could be interpreted. Interpreted horizons were well agreed with the logging results. 3 figs.

  19. Characterization of earthquake fault by borehole experiments; Koseinai sokutei ni yoru jishin danso no kenshutsu

    Energy Technology Data Exchange (ETDEWEB)

    Ito, H; Miyazaki, T; Nishizawa, O; Kuwahara, Y; Kiguchi, T [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    A borehole was excavated to penetrate the Nojima fault at the Hirabayashi area, to investigate the underground structures of the fault by observation of the cores and well logging. The borehole was excavated from 74.6m east of the fault surface. Soil is of granodiorite from the surface, and fault clay at a depth in a range from 624.1 to 625.1m. Observation of the cores, collected almost continuously, indicates that the fault fracture zone expands in a depth range from 557 to 713.05m. The well logging experiments are natural potential, resistivity, density, gamma ray, neutron, borehole diameter, microresistivity and temperature. They are also for DSI- and FMI-observation, after expansion of the borehole. The well logging results indicate that resistivity, density and elastic wave velocity decrease as distance from fault clay increases, which well corresponds to the soil conditions. The BHTV and FMI analyses clearly detect the fault clay demarcations, and show that elastic wave velocity and BHTV results differ at above and below the fault. 3 refs., 3 figs.

  20. Fault structure analysis by means of large deformation simulator; Daihenkei simulator ni yoru danso kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Y.; Shi, B. [Geological Survey of Japan, Tsukuba (Japan); Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1997-05-27

    Large deformation of the crust is generated by relatively large displacement of the mediums on both sides along a fault. In the conventional finite element method, faults are dealt with by special elements which are called joint elements, but joint elements, elements microscopic in width, generate numerical instability if large shear displacement is given. Therefore, by introducing the master slave (MO) method used for contact analysis in the metal processing field, developed was a large deformation simulator for analyzing diastrophism including large displacement along the fault. Analysis examples were shown in case the upper basement and lower basement were relatively dislocated with the fault as a boundary. The bottom surface and right end boundary of the lower basement are fixed boundaries. The left end boundary of the lower basement is fixed, and to the left end boundary of the upper basement, the horizontal speed, 3{times}10{sup -7}m/s, was given. In accordance with the horizontal movement of the upper basement, the boundary surface largely deformed. Stress is almost at right angles at the boundary surface. As to the analysis of faults by the MO method, it has been used for a single simple fault, but should be spread to lots of faults in the future. 13 refs., 2 figs.

  1. Array TDEM survey at the Yufuin fault; Yufuin danso ni okeru array shiki TDEM tansa

    Energy Technology Data Exchange (ETDEWEB)

    Mogi, T [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Tanaka, Y; Fukuda, Y [Kyoto University, Kyoto (Japan). Faculty of Science; Jomori, N [Chiba Electric Research Institute Co., Chiba (Japan)

    1996-10-01

    The array arrangement of receivers was studied to improve the resolution of LOTEM (long offset transient electromagnetics) survey. To eliminate the effect of underground structure from a source to a receiving point, continuous array arrangement from a source site is desirable. The survey at the Yufuin fault was carried out by arranging TEM receivers at intervals of 100m from the source. Since the synchronization between transmitting and receiving points by high-precision clock is essential, an amplifier for a flux gate magnetometer capable of measuring at four points at the same time was used. In the south plateau of the Yufuin basin, a relatively high resistivity stratum more than several tens ohm m exists at depth less than several hundreds meter, and a low resistivity stratum less than 10 ohm m exists under that. Those boundary depth increases toward the north up to 950m, and the depth subsequently decreases toward the north until the low resistivity stratum disappears. In addition, the uniform stratum of 1000m deep continues toward the north. Such precise resistivity structure around the fault was obtained by dense arrangement of measuring points. 4 refs., 7 figs.

  2. Recent advances in photoelectrochemistry. Part 1. Preparation and photocatalytic activities of semiconductor microcrystals; Saikin no hikari denki kagaku. 1. Handotai chobiryushi no chosei to hikari shokubai kassei

    Energy Technology Data Exchange (ETDEWEB)

    Yoneyama, H; Torimoto, T [Osaka Univ., Osaka (Japan). Faculty of Engineering

    1995-01-05

    The energy structure of semiconductor microcrystals with less than 10nm particle size is different from that of bulk semiconductor, and the reducing force of electrons and the oxidizing force of holes produced by light in microcrystals are larger than those of bulk semiconductor. Focusing on the application of semiconductor microcrystals to photocatalysis, the effects of the particle size and surface conditions of particles on photocatalytic activity are discussed. It has been shown that the change in the characteristics of semiconductor microcrystals depends on particle size, and microcrystals with narrow distribution of particle sized is necessary for the study of the characteristics of semiconductor microcrystals. An example of high efficient progress of CO2 direct reduction by the use of semiconductor microcrystals is introduced. It has been made clear that the photocatalytic activity of semiconductor is improved when a small amount of electrode catalyst is supported in it. A unique photocatalytic reaction which can not be observed with bulk particles can be progressed by the use of high oxidation and reduction ability caused by quantum size effect of semiconductor microcrystals. 26 refs., 2 figs., 1 tab.

  3. Recent advances in photoelectrochemistry. Part 3. Recent applications of photocatalysis; Saikin no hikari denki kagaku. 3. Hikari shokubai no jitsuyoka kenkyu no genjo

    Energy Technology Data Exchange (ETDEWEB)

    Murasawa, S [Ishihara Sangyo Kaisha Ltd., Osaka (Japan)

    1995-01-05

    Titanium oxide has been developed which can be put to practical use in photocatalysis, and trials have been carried out for the application to environmental processing. Some of the cases are quoted to investigate means for the application of the photocatalysis study. During the process of improving the light resistance of titanium oxide pigments, various knowledge on photocatalytic phenomena has been obtained, and titanium oxide having a strong enough activity suitable for practical use is obtained based on the knowledge. There are two methods for the application of photocatalysis to decomposition and deodorization of malodor in living space. Fixation of NOx has been studied to solve the problem of air pollution. A huge reactor is required if photocatalysis is applied to the treatment of a large quantity of water. Various kinds of approach may be needed to structure a compact reactor suitable for practical use. 14 refs., 3 figs., 2 tabs.

  4. Surface wettability control by titanium dioxide photo-induced reaction. Super-hydrophilic properties; Sanka chitan ni yoru hikari reiki shinsuika gijutsu. Hikari shokubai chosinsuisei

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T. [The University of Tokyo, Tokyo (Japan). Research Center for Advanced Science and Technology

    1999-05-01

    Hydrophilicity results when the surface of titanium dioxide is reduced for the specified oxygen to be replaced by hydroxyl groups. The ease with which such a structural change occurs is subject to variation between titanium dioxide crystal surfaces, and is dependent greatly on the atmosphere. No hydrophilic trend is observed in an atmosphere of oxygen only without moisture and, in darkness without light, hydrophobicity occurs early. Although the contacta angle titanium dioxide with water with stability is not known, yet it is presumed, on the analogy of the case of strontium titanate, that it is in the range of 20-40 degrees. A hydrophilic trend below the range is attrributed to structural changes. The control of surface wettability is one of the basic tasks to fulfill in various kinds of mechanisms and manufacturing processes. The technology of wettability control using a titanium dioxide coating which is quite durable will be applied not only to functions involving defogging, dripproof, and self-cleaning, but also to the control of heat transmission in the mechanism and to the bonding process. (NEDO)

  5. Surface wettability control by titanium dioxide photo-induced reaction. Super-hydrophilic properties. Sanka chitan ni yoru hikari reiki shinsuika gijutsu. Hikari shokubai chosinsuisei

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T. (The University of Tokyo, Tokyo (Japan). Research Center for Advanced Science and Technology)

    1999-05-01

    Hydrophilicity results when the surface of titanium dioxide is reduced for the specified oxygen to be replaced by hydroxyl groups. The ease with which such a structural change occurs is subject to variation between titanium dioxide crystal surfaces, and is dependent greatly on the atmosphere. No hydrophilic trend is observed in an atmosphere of oxygen only without moisture and, in darkness without light, hydrophobicity occurs early. Although the contacta angle titanium dioxide with water with stability is not known, yet it is presumed, on the analogy of the case of strontium titanate, that it is in the range of 20-40 degrees. A hydrophilic trend below the range is attrributed to structural changes. The control of surface wettability is one of the basic tasks to fulfill in various kinds of mechanisms and manufacturing processes. The technology of wettability control using a titanium dioxide coating which is quite durable will be applied not only to functions involving defogging, dripproof, and self-cleaning, but also to the control of heat transmission in the mechanism and to the bonding process. (NEDO)

  6. Fault analysis in the very shallow seismic reflection method; Gokusenso jishin hanshaho ni okeru danso kaiseki. 1

    Energy Technology Data Exchange (ETDEWEB)

    Nagumo, S; Muraoka, S; Kaida, Y; Takahashi, T [OYO Corp., Tokyo (Japan)

    1996-10-01

    To effectively use the very shallow seismic reflection for active fault survey, a method has been investigated by which fault structures can be appropriately reconstructed from the fault information detected in the original records. The first step of reconstructing the fault system from the travel time reflection curve was to grasp an outline of fault structure from the patterns of travel time curve observed in the original record. For the very shallow seismic reflection method, especially, the low velocity layers in a shallow part succeeding from the ground surface made the issue complicated. Then, the travel time reflection curves were calculated in the case of existing several horizontal reflection surfaces in the surface layer. The constant values, mean velocities to the depth at individual reflection surfaces were used for the approximation of velocities. The outline of fault structure was grasped from the observation of original record. Then, the structure was reconstructed from the travel time curves. When the mean velocity in the medium was known, reconstruction of the feature of reflection surfaces from the travel time curves could be determined by simple mapping. When the mean velocity was unknown, it was calculated using the reciprocal travel time from the common reflection surface for individual reflection surfaces. 7 figs.

  7. Evaluation of permeability of Nojima fault by hydrophone VSP; Hydrophone VSP ni yoru Nojima danso no tosuisei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kiguchi, T; Ito, H; Kuwahara, Y; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    The multi-offset hydrophone VSP experiments were carried out using a 750m deep borehole as the oscillation receiver, which penetrates the Nojima fault, to detect water-permeable cracks and evaluate their characteristics. Soil around the borehole is of granodiorite, and fault clay is found at a depth in a range from 623 to 624m. A total of 4 dynamite tunnels were provided around the borehole as the focus. The VSP results show that the tube waves are generated at 22 depths, including the depth at which fault clay is found. However, these waves are generated at only 6 depths in an approximately 150m long fracture zone, suggesting that the cracks in the zone are not necessarily permeable. It is also found that crack angle determined by the analysis of tube waves almost coincides with that of fault clay determined by the core, BHTV and FMI, and that permeability is of the order of 100md at a depth of fault clay or shallower. 3 refs., 2 figs., 2 tabs.

  8. Velocity structure of Nojima-fault by VSP method; VSP ho ni yoru Nojima danso no sokudo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Kuwahara, Y; Ito, H; Kiguchi, T; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    In order to investigate in detail structures of the fractured fault band, the VSP tests were conducted using a 750m deep borehole penetrating the Nojima fault in Awaji Island. The borehole penetrates the fault clay band at a depth of 624m in the Hirabayashi area. The offset VSP survey, conducted by the aid of hydrophone through the naked borehole, detects many characteristic phenomena resulting from the fault fracture. Largely fractured lithofacies are found by the core observation at a depth in a range from 557 to 673m. P-waves propagate at 4.6 and 5.1km/s above and below the fractured band, respectively. The fractured band is subdivided into 2 sections, both being of low speed of 4.5 and 3.1km/s. The X1 and X2 phases resulting from the fault fracture are also observed, above and below the fractured band. The causes for these wave phases are now under investigation. 4 figs.

  9. Preliminaries on core image analysis using fault drilling samples; Core image kaiseki kotohajime (danso kussaku core kaisekirei)

    Energy Technology Data Exchange (ETDEWEB)

    Miyazaki, T; Ito, H [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    This paper introduces examples of image data analysis on fault drilling samples. The paper describes the following matters: core samples used in the analysis are those obtained from wells drilled piercing the Nojima fault which has moved in the Hygoken-Nanbu Earthquake; the CORESCAN system made by DMT Corporation, Germany, used in acquiring the image data consists of a CCD camera, a light source and core rotation mechanism, and a personal computer, its resolution being about 5 pixels/mm in both axial and circumferential directions, and 24-bit full color; with respect to the opening fractures in core samples collected by using a constant azimuth coring, it was possible to derive values of the opening width, inclination angle, and travel from the image data by using a commercially available software for the personal computer; and comparison of this core image with the BHTV record and the hydrophone VSP record (travel and inclination obtained from the BHTV record agree well with those obtained from the core image). 4 refs., 4 figs.

  10. The effect of technological changes on unemployment in the beverage sector of the South African economy / A.K. Danso

    OpenAIRE

    Danso, Alex Kwame

    2007-01-01

    The ability of the South African economy to absorb labour has been declining since the 1960's, with the manufacturing sector employment declining since 1990. The decline in manufacturing jobs flies in the face of increased output of the sector. This trend is attributed to the application of technology and sophisticated equipments in the manufacturing process leading to a loss of jobs, particularly for unskilled labour. Unemployment in South Africa has become one of the biggest ...

  11. Consideration on characteristics of faults distributed at around Fujigawa river mouth; Fujigawa kako shuhen ni okeru danso kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Iwashita, A; Misawa, Y [Tokai University, Tokyo (Japan)

    1997-10-22

    From the sonic prospecting on the ground, it was confirmed that faults distributed in the inner part of Suruga Bay extend near the Fujigawa river mouth. While, faults in the sea bottom were found by the sonic prospecting using a single air-gun. However, continuity of faults running from the land to the sea has not been reported. This paper describes the continuity of Fujigawa fault system running from the land to the sea around Fujigawa river mouth along the subduction zone of Philippine Sea Plate using single air-gun seismic reflection records. Locations of the faults can be expressed as fracture information of linearment obtained from the satellite remote sensing images, which agreed well with those found by the Active Fault Research Association. As a result of the image processing, they agreed distinctly with the topography of Fujigawa fault system. Thus, much more accurate analysis can be performed by comparing the regional information by the remote sensing with the sonic seismic reflection profiles. 3 refs., 2 figs.

  12. Fault analysis in the very shallow seismic reflection method. Part 3. Migration; Gokusenso hanshaho ni okeru danso kaiseki. 3. Migration

    Energy Technology Data Exchange (ETDEWEB)

    Nagumo, S; Muraoka, S; Takahashi, T [OYO Corp., Tokyo (Japan)

    1997-10-22

    Concerning the analysis of data obtained by the seismic reflection method, migration in the very shallow layer is discussed. When the dip angle of the reflection plane involved is disclosed by DMO conversion, the amount of migration (travelling sideways) can be calculated by use of simple geometrical formulas though on the presumption that the sector velocity is constant. Categorized into this technique are such methods as DMO conversion migration, direct dip migration, F-K method, and finite difference method. This means that waveforms are not damaged by migration processing although elongation occurs due to time base conversion. When it is taken into account that waveform distortion is generally grave in the migration related methods widely in use, this feature has to be said valuable in holding information on faults. This is especially advantageous in the very shallow layer because the amount of migration is proportionally larger when the level is deeper and, in addition, migration processing is useful when it is necessary to know more accurately the character of the fault plane. 8 figs.

  13. Fault analysis in the very shallow seismic reflection method. 2; Gokusenso hanshaho ni okeru danso kaiseki. 2

    Energy Technology Data Exchange (ETDEWEB)

    Nagumo, S; Muraoka, S; Takahashi, T [Oyo Corp., Tokyo (Japan)

    1997-05-27

    Fault analysis is required in addition to the ordinary process of structural analysis (CDP stacking) for the examination of discontinuity in the reflection horizon in question. The fault shape restoration principle is that the reflection point of a reflection wave observed at a certain receiving point is on an ellipse with the shock point and receiving point at its focal points and that the sum of the distances between the reflection point and the focal points is equal to the reflection wave propagation time. The DMO velocity is worked out by calculation using the positive travel time and inverse travel time from the common reflection surface. When the reflection surface is inclined by {theta}, the average interval velocity/cos{theta} is called the DMO velocity. When the reflection surface inclination and the average interval velocities are determined separately in this way, the position of the reflection point may be worked out, and this enables the calculation of the amount of migration (lateral movement). The reflection wave lineups carried by the original record are picked up one by one, and the average interval velocities are treated very prudently. After such a basic DMO conversion treatment, the actualities of the fault are described fairly correctly. 3 figs.

  14. Seismic reflection survey of the Uemachi fault in Osaka Prefecture; Osaka Uemachi danso no hanshaho danseiha tansa

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, Y [Geological Survey of Japan, Tsukuba (Japan); Yoshizawa, M; Hirooka, S [Nikko Exploration and Development Co. Ltd., Tokyo (Japan); Yokota, H; Ito, S [Hanshin Consultant Co., Osaka (Japan); Hayashi, K; Aizawa, H

    1997-05-27

    Reflection survey is conducted using three traverse lines in Sakai City for confirming the presence of a southward stretch of the Uemachi fault underground along the western periphery of the Uemachi terrace, Osaka, and for elucidating its connection to the Sakamoto fault distributed near Izumi. Another reflection survey is conducted in the bed of Kanzaki river, Osaka, for the confirmation of its connection to the Nembutsuji-zan fault in Senri hillock. It is estimated on the basis of boring data that there exists another flexural structure approximately 3km south of the flexural structure whose presence is confirmed by the Sakai second traverse line. Accordingly, possibilities are high that the southward stretch of the Uemachi fault connects to the Sakamoto fault. The confirmation by the Kanzaki river traverse line of the flexural structure again confirms the continuity between the Uemachi fault and Nembutsuji-zan fault. The above-said findings enable an inference that the three faults of Nembutsuji-zan, Uemachi, and Sakamoto constitute a chain of active faults. Furthermore, there exists an active fault to the south of the Sakamoto fault, which zigzags to the south on the right-hand side as far as the south of the Kumeda pond. Accordingly, the Uemachi fault system as a whole spans approximately 43km from the northern end of the Nembutsuji-zan fault as far as the south of the Kumeda pond. 5 refs., 6 figs.

  15. Application of vector CSAMT for the imaging of an active fault; CSAMT ho ni yoru danso no imaging

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, T; Fukuoka, K [Oyo Corp., Tokyo (Japan)

    1997-05-27

    With an objective to identify three-dimensionally resistivity in deep fault in the Mizunawa fault in Fukuoka Prefecture, a measurement was carried out by using the CSAMT method. The measurement was conducted by arranging seven traverse lines, each line having observation points installed at intervals of about 500 m. Among the 68 observation points in total, 33 points performed the vector measurement, and the remaining points the scaler measurement. For observation points having performed the vector measurement, polarized wave eclipses were depicted in the electric field to discuss which direction the current will prevail in. For analyses, a one-dimensional analysis was performed by using an inversion with smoothing restriction, and a two-dimensional analysis was conducted by using the finite element method based on the result of the former analysis. The vector measurement revealed that the structure in the vicinity of a fault was estimated to have become complex, and the two-dimensional analysis discovered that the Mizunawa fault is located on a relatively clear resistivity boundary. In addition, it was made clear that the high resistivity band may even be divided into two regions of about 200 ohm-m and about 1000 ohm-m. 2 refs., 7 figs.

  16. Air environment purification using photocatalyst. Hikari shokubai ni yoru taiki kankyo joka

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, K [National Institute for Resources and Environment, Tsukuba (Japan)

    1993-12-02

    Noticing that metal oxides have photocatalysis for reduction in NOx concentration and examining effects of the TiO2 selected on removal of pollutant, the paper proposes a direct purification method for the air environment. Since TiO2 causes electron excitation meeting near ultraviolet irradiation, it manifests a catalytic function for various oxidation/reduction reactions. Details of the reaction mechanism are unknown, various active oxygen species generated on the surface of TiO2 under light irradiation oxidize NOx and acquire it as nitric acid on the surface. It is found that mixture of activated carbon of low hygroscopicity with TiO2 is effective to prevent a tendency of NO to desorb before NO becomes nitric acid. What 40% of the catalyst with fluorine resin is formed into like a sheet shows a high removal rate even in the amount of ultraviolet irradiation in a winter cloudy day in the wide range of 0.5 - 95.0% of NOx and SO2, and if the photocatalyst is applied to the side wall of city buildings, the NOx concentration is estimated to be reduced by as much as 20%. 5 refs., 3 figs.

  17. Laser material purification of neodymium. Hikari reiki seiseiho ni yoru neodymium no kojundoka

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, Y.; Ozaki, T.; Yoshimatsu, S. (National Research Institute for Metals, Tokyo (Japan)); Chiba, K.; Umeda, H.; Saeki, M. (Nippon Steel Corp., Tokyo (Japan))

    1991-05-20

    Selective photoexcitation and photoionization of neodymium atoms were studied basically by using laser. Also, using their properties, feasibility of laser material purification (LPM) technology in gaseous phase was presented. In the selective 3-step ionization, laser beam with two kinds of proper wave length causes resonance exitation of the target element, which goes up to the excitation level of the first step, and the element is ionized by the second laser beam and the third laser beam. The 3-step ionization scheme by a single wave length laser beam of 577.612nm was used for the ionization of Nd. Nd ionized selectively by laser beam was recovered as thin layer at the negative potential side of plane electrodes placed at both sides of the laser irradiation area. In the layer formed by the TPD technology with this scheme, it is possible to decrease impuritis such as Pr by 1/16 and to form highly purified thin layer. 13 refs., 12 figs., 1 tab.

  18. Development and demonstration of optical polarization controller; Hikari henpa seigyo sochi no kaihatsu to jissho

    Energy Technology Data Exchange (ETDEWEB)

    Kurono, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-04-01

    If fiber transmission light can be controlled in a stabilized polarization state, realization of coherent optical communication is anticipated. In the case of adopting it to OPGW, however, it is necessary to compensate high speed polarization variation caused by lightning strike. But this was difficult in the conventional method. Accordingly, a high speed polarization control method was proposed which uses an electric effect of lithium niobate (LN) crystals. In the study, a polarization control unit was manufactured based on the method proposed and the performance was demonstrated. As a result of measuring output light with input light changed in every state of polarization, the object horizontal polarization component obtained a stabilized light intensity at {+-}0.1dB, and a light intensity of the component slipped out of the horizontal polarization was suppressed under -20dB. To cope with the polarization variation by lightning strike, it is necessary to make the control delay 10{mu}sec or below, and improvement in processing unit, etc. may make it possible since LN crystals respond below 1{mu}sec. High speed control of the infinitely continuing arbitrary polarization variation became possible. 14 refs., 19 figs.

  19. Application of photocatalysts for amenities; Kaiteki kukan no tameno hikari shokubai

    Energy Technology Data Exchange (ETDEWEB)

    Sugawara, T. [Akita Univ., Akita (Japan). Mining College

    1996-03-01

    Catalysts with strong decomposing power are necessary in removing the stink of toilets and diapers, the smoke of cigarettes, lampblack in kitchens and mold in bathrooms etc. One of such catalysts attracting attention is titania (Ti02) photocatalyst. Titania has a strong oxidizing force due to its ability to absorb light with a wavelength under 400nm, and meanwhile this substance itself is chemically stable and tender to environment. In this paper, simultaneously with the introduction of the design examples applying the performance and properties of such catalysts, the evaluation on the performance of utility photocatalysts is described. The examples of using tiles with titania coated on ceramic tiles and the photocatalysts obtained by fixing supermicro-particles of titania catalysts with fluorine resin as a binder to decompose the oil vapor near a ventilation fan above a kitchen range and the tobacco tar whose concentration level is as in a living room are introduced as the design examples of utility photocatalysts. 13 refs., 6 figs.

  20. Evaluation for characteristics of around the Nojima fault; Butsuri tansa ni yoru `Nojima jishin danso` shuhen no jiban bussei ni kansuru ichihyoka

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, K; Tsuji, T [Newjec Inc., Osaka (Japan); Tsuji, M [OYO Corp., Tokyo (Japan)

    1996-05-01

    Various surveys were conducted for the area around the Nojima fault, including ground surface, two-dimensional electrical and boring surveys and elastic wave tomography, in order to grasp properties of the ground around the `Nojima earthquake fault.` The resistivity image method as one of the two-dimensional electrical methods was used to grasp fault shapes over a wide range of the 1.6km long section extending between Esaki and Hirabayashi. The courses of traverse were set in the direction almost perpendicular to the fault. Boreholes were excavated and elastic wave tomography was conducted between the boreholes on the 9th and 17th courses of traverse, to confirm ground/mountain conditions and to compare the results with observed elastic wave velocities. Very low resistivities are observed at places where granite is distributed, suggesting that the fault-induced changes are not limited to the area around the fault. The zone in which elastic wave velocity decreases is narrow, 10m at the longest, at a velocity of 2.4km/s or lower, which is a low velocity for that propagating in granite. 5 refs., 4 figs.

  1. Acoustic surveys of the southern extension of the Tomikawa fault off Kamiiso in Hakodate bay, southwest Hokkaido; Hakodatewan Kamiisooki ni okeru Tomikawa danso enchobu no onpa tansa

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, Y; Sagayama, T; Osawa, M; Hamada, S; Suga, [Hokkaido Geological Survey, Sapporo (Japan)

    1997-10-22

    With an objective to identify extension into sea area of the Tomikawa fault in southwest Hokkaido, an acoustic survey was carried out off Kamiiso in Hakodate Bay. Using a sound wave exploring machine transmitting frequencies from 5.5 to 8.5 kHz, the acoustic survey was conducted on a workboat cruising at speeds of 4 to 6 knots. The courses of traverse were set on the sea area off from Kamiiso Tomikawa Town to Moheji Town based on the sediment distribution map and the geological map. A total of 17 courses were set: 16 in the east to west direction so as to cross the extension of active faults on the land, and one in the south to north direction. The east-west courses had a length of about 2 km with the line interval of about 300 m, while the south-north course extended nearly parallel with the coast line over a distance of 4.8 km. As a result of the present investigation, verification was given on existence of boundary faces with different sediment structures and displacement falling eastward on several courses of traverse running from east to west. If the locations of these boundary faces are connected, its strike agrees well with the strike of the Tomikawa fault on the land. From the fact that its extension is linked to the end section of the fault, a possibility was shown that the land fault may be extending into the sea area. 8 refs., 4 figs.

  2. Extension of the Fukaya fault and deep structure of the Konan terrace; Fukaya danso no encho to Konan daichi no chika kozo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, K; Kano, N; Yokokura, T; Kiguchi, T; Yokota, T; Tanaka, A [Geological Survey of Japan, Tsukuba (Japan); Sato, H [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1997-10-22

    With an objective to elucidate the relationship between the central tectonic line in the Kanto area and the active faults appearing in topography, seismic exploration using the reflection method has been carried out. The course of traverse was set in the south west to north east direction starting from the north east part of the Kanto mountainous area to the Menuma lowland passing through the Konan high plain. The line crosses nearly perpendicularly the direction in which the general beds in this area run. A 400-kg weight was used as a vibration source in the western half of the course of travel, and the MinivibT15000 (made by IVI Corporation) in the eastern half. Considerations given based on the preliminary CMP polymerization time cross section may be summarized as follows: the Fukaya fault cannot be tracked topographically further to the south east side than Mikejiri in Kumagaya City, but the reflection face from CMP 2050 to about 2100 shows an inclined bed on the south west side and a horizontal bed on the north east side; judging from change in the inclination in the beds, the Fukaya fault is thought to extend to the south east direction; the location of inclination change on the cross section turns to the south west side as the depth increases; and, if this is regarded as the fault face, the Fukaya fault could be said an inverse fault. 5 refs., 2 figs.

  3. Fault fracture zone evaluation using borehole geophysical logs; case study at Nojima fault, Awaji island; Kosei butsuri kenso ni yoru danso hasaitai no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, R; Omura, K [National Research Institute for Disaster Prevention, Tsukuba (Japan); Yamamoto, T [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)

    1997-10-22

    Ikeda, et al., in their examination of log data obtained from a borehole (2000m deep) drilled at Ashio, Tochigi Prefecture, where micro-earthquakes swarm at very shallow levels, pay special attention to porosity. Using correlationship between the porosity and elastic wave velocity/resistivity, the authors endeavor to find the presence of secondary pores, dimensions of faults, composition of water in strata in faults, and difference in matrix between rocks, all these for the classification and evaluation of fault fracture zones. In the present report, log data from a borehole (1800m deep) drilled to penetrate the Nojima fault (Nojima-Hirabayashi, Awaji island) that emerged during the Great Hanshin-Himeji Earthquake are analyzed in the same way as the above-named Ashio data, and the results are compared with the Ashio results. Immediately below the Nojima-Hirabayashi fault fractured zone, stress is found remarkably reduced and the difference stress quite small in size. This is interpreted as indicating a state in which clay has already developed well in the fault fractured zone ready to allow the occurrence of shear fracture or a state in which such has already occurred for the release of stress. 4 refs., 5 figs.

  4. Simulation of fault-bend fold by incompressible Newtonian fluid; Hiasshukusei Newton ryutai ni yoru danso oremagari shukyoku kozo no simulation

    Energy Technology Data Exchange (ETDEWEB)

    Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-10-22

    Incompressible Newtonian fluid simulation is experimentally applied to faults typical of the compression and extension fields. A fault-bend folding structure of the flat-ramp flat fault in the compression field and a folding structure of a normal fault in the extension field are studied, and the results are compared with those obtained by the balanced cross section method. The result of calculation indicates that the velocity gradient with the ramp angle set at 30deg is correspondent to stress and that stress concentration is taking place at the ramp section of the fault. This solution is an approximation and does not necessary support the conservation of area but, when the ramp angle is allowed to change from 10 through 40deg, it is found that the conservation of area holds though roughly. It is found that the configuration of the folding structure formed by a flat-ramp flat fault is positioned between the anomalous-mode layer parallel shear typical of a balanced cross section and the folding structure formed by a vertical shear. 7 refs., 7 figs.

  5. Fault detection by Turam TEM survey. Numerical model studies and a case history; TEM ho Turam sokutei haichi ni yoru danso kenshutsu no kokoromi. Model keisan to jisshirei

    Energy Technology Data Exchange (ETDEWEB)

    Wada, K; Tsutsui, T [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan); Ito, T [Chiba Univ., Chiba (Japan). Faculty of Science; Takeuchi, A [Toyama University, Toyama (Japan). Faculty of Science; He, P [Power Reactor and Nuclear fuel Development Corp., Tokyo (Japan)

    1997-05-27

    With an objective to detect faults estimated to exist along the Shigesumi valley in the Kamioka mine, discussions were given by using electromagnetic survey, which uses the Turam measurement arrangement based on the TEM method, and three-dimensional model calculations. The Turam measurement arrangement, which installs transmission loop fixedly, is used to identify nature and distribution of electrically conductive objects upon noticing abnormal portions in magnetic fields in the measurement data. In the model calculation, the plate model calculation method and the FDTD method were used, and so was the calculation code TEM3DL. The result revealed that strong topographical influence is seen from steep V-shaped valley existing along the traverse line in the measurement data, but an abnormal resistivity band accompanying remarkable distortion in the curve was detected. According to the result of the model calculation, anomaly detection may be found difficult in locations where a low resistivity band has not grown enough locally. It was possible from these facts to assume a model in which the low resistivity band exists directly below the Shigesumi valley, suggesting existence of faults. 2 refs., 8 figs.

  6. Results of geophysical survey on Hanaore-fault in the Kyoto urban area; Butsuri tansa ni yoru Kyoto shigaichi ni okeru Hanaore danso chosa

    Energy Technology Data Exchange (ETDEWEB)

    Yoshioka, T. [Geological Survey of Japan, Tsukuba (Japan); Echigo, T. [Osaka Soil Test, Osaka (Japan); Toshioka, T.; Matsubara, Y. [Oyo Corp., Tokyo (Japan)

    1997-05-27

    This paper reports results of gravity survey and seismic survey using the shallow bed reflection method to identify distribution of the Hanaore fault in the Kyoto urban area. In the gravity survey, level differential structure caused by the fault was identified as an abrupt change in Bouger anomalous values. The continuity therefrom made the estimation possible on existence and positions of such faults as the Hanaore fault belonging to the Hanaore fault system, the Shishigaya fault, the Kaguraoka fault, and the Okazaki fault. The estimation as a result of the gravity survey include the following findings: the Hanaore fault runs from south of the Yoshidayama in the south-north direction; the distribution of the Okazaki fault has a level differential structure falling on the east side; the structure shows low Bouger anomaly distribution; and this area forms a rift valley belt. In the seismic survey using the shallow bed reflection method, no distinct reflection plane considered as the basement was verified because of influence from urban area noise. However, it was possible to estimate such an underground structure as a monoclinal fold from shapes of the reflection plane and the distribution depths. 7 refs., 5 figs.

  7. Airborne gamma-ray survey around the Negoro fault. 1; Negoro danso shuhen chiiki ni okeru kuchu {gamma} sen tansa. 1

    Energy Technology Data Exchange (ETDEWEB)

    Nakayama, E.; Kasuya, Y.; Hasegawa, H. [Aero Asahi Corp., Tokyo (Japan); Tsukuda, E. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    An airborne gamma-ray survey was carried out to investigate the active fault system in the central structure line in the peripheral area of the city of Wakayama. At the same time, with an objective to enhance applicability of the airborne gamma-ray survey to active fault investigation, fundamental data were acquired and discussed. The measurement data were processed according to the standard method specified by IAEA. An ID-FFT filter and a nonlinear filter were employed to extract anomalous gamma-ray intensity values. The gamma-ray intensity distribution chart shows a noticeable positive anomalous area extending from the central part of the western edge to the north-east direction. This area agrees nearly well with the Negoro fault, but its peak portion is positioned slightly more to south than the position of the Negoro fault shown in existing data. The Sakuraike fault and the vicinity of the central structure line also show positive anomaly as a whole, particularly remarkably in the vicinity of their converging portion. However, differing from the vicinity of the Negoro fault, the areas are not extracted as an anomalous area which has directionality and extends in a line form. One of the factors for this would be that it is a fault in unsolidified deposits with low opening trend, differing from the one in solidified rocks. 1 fig., 3 tabs.

  8. Polarimetric borehole radar measurement near Nojima fault and its application to subsurface crack characterization; Polarimetric borehole radar ni yoru Nojima danso shuhen no chika kiretsu keisoku jikken

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M.; Taniguchi, Y.; Miwa, T.; Niitsuma, H. [Tohoku University, Sendai (Japan); Ikeda, R. [National Research Institute for Disaster Prevention, Tsukuba (Japan); Makino, K. [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)

    1997-05-27

    Practical application of subsurface crack characterization by the borehole radar measurement to which the radar polarimetric method was introduced was attempted to measuring objects for which the borehole radar has not been much used, for example, the inside of low loss rock mass or fracture zone where cracks tightly exist. A system was trially manufactured which makes the radar polarimetric measurement possible in the borehole at a 1000m depth and with a about 10cm diameter, and a field experiment was conducted for realizing the subsurface crack characterization near the Nojima fault. For the measuring experiment by the polarimetric borehole radar, used were Iwaya borehole and Hirabayashi borehole drilled in the north of Awaji-shima, Hyogo-ken. In a comparison of both polarization systems of Hirabayashi borehole, reflected waves at depths of 1038m and 1047m are relatively stronger in both polarization systems than those with the same polarization form and at different depths, whereas reflected waves around a 1017m depth are strong only as to the parallel polarization system. Characteristics of the polarization in this experiment indirectly reflect crack structures. 6 refs., 6 figs., 1 tab.

  9. {Gamma}-ray prospecting of major faults of Miocene basins; Chushinto taisekibon no keisei ni kakawaru danso wo taisho to shita hoshano tansa

    Energy Technology Data Exchange (ETDEWEB)

    Iwata, A. [Shimada Technical Consultants, Ltd., Shimane (Japan); Yamauchi, S.; Adachi, K. [Shimane University, Shimane (Japan); Yoon, S.; Kil, R, [Pusan National University, Pusan (Korea, Republic of)

    1997-05-27

    The Masuda basin in the western edge of Shimane Prefecture and the Pohang basin in the southern part of the east cost of Korea had been formed in the middle of Miocene epoch of Neogene period, and show similarity in their geology and structure. A gamma-ray prospecting was carried out on major faults that have had been involved in forming these basins. A portable gamma-ray analysis device, model 8630 made by Clearpulse Corporation was used for the measurement. Emanation of radon and its migration are known generally, whereas rise in radon is recognized above crevices with deep opening trend. The present faults having been involved in forming the basins are thought to have large falls in positive faults and often accompany crevices with opening trend. This estimation is thought endorsed by the result of the present prospecting. In addition, such faults may often form geological boundaries, and the present survey has had geological division made easily with total gamma-ray. A gamma-ray exploration using both of the spectrum method and the total count method is a process sufficiently utilizable in geological surveys on structures in peripheries of sedimentary basins. 6 refs., 7 figs.

  10. Special issue on frontiers of chemistry related to electrical and electronic engineering. Part 4.; Artificial photosynthesis and photoelectrochemistry; Denki/denshi kogaku ga hiraku atarashii kagaku no sekai. 4.; Jinko hikari gosei to hikari denki kagaku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuo, T [Kyushu Univ., Fukuoka (Japan). Faculty of Engineering

    1993-09-20

    Since light can be transformed into electricity, electrolysis of water using light is possible naturally, and photosynthesis in the nature is based on this principle. The reaction field in which electrochemical energy necessary for decomposition of water is generated using light at the first process of photosynthesis is a biofilm less than 10nm thick which is called thylakoid film. In this article, the effects are roughly explained which have been made for constructing an artificial system corresponding to the thylakoid film. Accumulation of knowledge of the molecular level is necessary for the construction of the artificial system and the three dimensional structure concerning the reaction center of photosynthetic bacteria has been determined. At the reaction center, oxidation species of electron donor and reduction species of electron acceptor are generated by charge separation which succeeds electron excitation by light energy. In order to lead the above process to materialistic production, efforts are being made for construction of a reaction center model compound for artificial photosynthesis from both physical chemistry and organic chemistry and the positive results have steadily been obtained in the development of photocatalysis of a semiconductor. 9 figs.

  11. Control of surface wettability by light illumination: surface wettability control utilizing photo-induced surface reaction of titanium oxide; Hikari de nure wo seigyosuru - sanka chitan no hikari reiki hanno wo riyoshtia nure seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T.; Hashimoto, K. [The Universityof Tokyo (Japan)

    1999-02-15

    We report photo-generation of highly hydrophilic surface of titanium dioxide. The photo-induced hydrophilicizing is achieved by photo-generation of Ti{sup 4+} to Ti{sup 3+} at definite sites on the surface, resulting in preferential adsorption of hydroxyl groups on corresponding oxygen vacant sites. We also report the photo-generation of titanium dioxide amphiphilic surface on definite photo illumination condition. The unique character of this surface is ascribed to the microstructure of hydrophilic and oreophilic domain. The hydrophilic or amphiphilic titanium dioxide coating can be applied for antifogging mirror or glass and also self-cleaning paint for various industrial materials. Several commercial applications including antifogging automobile side-view mirror or self-cleaning exterior ceramic tile has been starting to hit the market. (author)

  12. Effect of surface irradiation during the photo-CVD deposition of a-Si:H thin films. Hikari CVD ho ni yoru amorphous silicon sakuseiji no kiban hikari reiki koka

    Energy Technology Data Exchange (ETDEWEB)

    Tasaka, K.; Doering, H.; Hashimoto, K.; Fujishima, A. (The University of Tokyo, Tokyo (Japan))

    1990-12-06

    This paper shows the impact of the irradiation from an additional light source during the deposition of hydrogenated amorphous silicon by photo-CVD deposition. Using a mercury sensitized photo-CVD process from Disilan (Si {sub 2} H {sub 6}) and hydrogen, silicon was deposited. A 40W low pressure mercury lamp was applied as the light source. A portion of the substrate was in addition irradiated using an Xg-He lamp through a thermal filter. Irradiation of the substrate using only Xg-He lamp produced no deposition, since this light has a wavelength which is too long to produce the SiH {sub 3}-radicals needed for Si deposition. The additional Xg-He light source was discovered to cause an increased thickness of deposited a-Si:H film and a transmission of the band structure. The reasons of these are considered that the influence of irradiation is not limited to film thickness, but that irradiation also impacts the composition of the a-Si:H film so as to cause a reduction in the hydrogen content. 10 figs., 1 tab.

  13. Committee report on visual appearance of neon lights. Neon no hikari no miekata ni kansuru tokubetsu kenkyu iinkai hokoku

    Energy Technology Data Exchange (ETDEWEB)

    Kansaku, H. (Chukyo University, Nagoya (Japan). Faculty of Letters)

    1991-04-25

    Were summarized the results of experiments and literature searches, conducted by the Commettee on Visual Appearance of Neon Lights,'' which was set up to provide scientific and basic data for understanding of relationship between neon lights and psychological reaction of human, and for realizing of neon sign advertisements with playing a role as neon lights and without any environmental problems. Analytical results of influences of six colors, such as red, yellow, green, blue, violet, and white, brightnesses, and flickering frequencies to the psycological reaction of human on the direct observations of neon lights were described. Results of influences of the neon light incidence into the room to the psychology of residents were also introduced. Furthermore, evaluation of neon lights as an aspect was discussed. Consequently, based on the combination of activity and estimativity, some attentions to be payed on the setting-up of neon lights were pointed out. A red flickering neon light'' was given as clearly a bad example. 2 figs.

  14. FY1995 optoelectronic devices and circuits for terabit class network; 1995 nendo terabit kyu network yo hikari denshi device kairo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The necessary technology realizing Terabit class optical network is the signal multiplexing both in temporal and spectral domains. Controllability of ultrafast optoelectronic systems is therefore the priority issue. Specifically we chose semiconductor lasers as the key devices. The methodology for performance improvement and the creation of novel functionality are investigated. Firstly compression of semiconductor laser pulse reached the world record of 65 femto second. Secondly a proposal was made to control mode locked semiconductor lasers via subharmonic synchronization and a substantial phase noise reduction was demonstrated. Thirdly a new technology was developed to realize broadband anti-reflection coating on semiconductor laser amplifier facet, bringing about significant performance improvement. To compensate the dispersion induced signal distortion a broadband semiconductor laser amplifier four wave mixing was analyzed and also demonstrated experimentally. (NEDO)

  15. Power feeding to terminal devices in optical subscriber network; Hikari fuaiba tsushin ni okeru tanmatsu kiki eno kyuden

    Energy Technology Data Exchange (ETDEWEB)

    Yamasaki, M

    1998-09-01

    This paper outlines present state of the feeding system in the light access system in consideration of backup in case of home power failure. In the optical communication, equipment with bilateral conversion function for light and electricity has to be installed both on communication service side and home side. Outline of the light access system and equipment requiring backup are shown. The following items are explained: main types of the light access system, such as FTTC (fiber to the curb), FTTP (fiber to the pole), FTTH (fiber to the home) and HFC (hybrid fiber coax), and the feeding system; problems on feeding system for the light access system. Key elements of ONU (optical network unit) for FTTH and construction of the ONU power source are illustrated. The ONU power source is composed of a backup power supply unit and main body supply unit. Backup power is indispensable to the ONU and analog telephones: output is supplied by the backup batteries in power failure. For miniaturization of the backup power source, power supply circuits and backup batteries have to be miniaturized simultaneously. History of miniaturization is explained on the experimental models. 6 refs., 7 figs., 1 tab.

  16. FY 1995 research for optical diagnosis by contrast agent; 1995 nendo hikari toresa wo riyoshita atarashii bunko shindanhono kiso kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For expanding the optical diagnosis to clinical medicine, we tried to use the several optical characteristics of living tissues in addition to absorption measurements of blood. The scattering and luminescence of the tissue were examined in detail. The final goal of the research is to introduce the contrast agent active in the near-infrared region. (1) We have succeeded in obtaining the scattering and absorption coefficients separately from the time-resolved data of living tissues such as rat head and even human head. Then, based on the basic equations derived from our experiments, the quantification of the absolute absorbance was performed. (2) Using the near-infrared fluorescent dye, Rhodanine 800, we could monitor the energy state of tissues. We concluded that Rhodamine 800 is the possible candidate for energy-reporting contrast agent applicable to near-infrared spectrophatometry. (NEDO)

  17. Temperature measurement of geothermal wells by optical fiber sensor; Hikari fiber sensor wo mochiita chinetsusei no ondo bunpu keisoku

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, N; Sakaguchi, K [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    Experiments of temperature measurement were conducted in high temperature and high pressure geothermal wells using optical fiber sensor. A temperature measurement system using optical fiber sensor was applied to geothermal wells. Working availability was confirmed under the condition up to the depth of 1,750 m and the temperature of 240 centigrade. Observed values agreed well with those observed by the conventional temperature logging. Durability of the optical fiber sensor was also sufficient. The maximum standard deviations of measured values were 1.3 centigrade at the depth of 1,750 m at 195 centigrade for the loop-type sensor, and 3.7 centigrade at the depth of 365 m at about 200 centigrade for the single-end sensor. Although the accuracy was inferior to the conventional measurement using a thermo couple, it was enough to be applied to usual temperature logging. Furthermore, for this system, the temperature profile in the whole well can be monitored, simultaneously. Through the experiments, the detailed successive change of temperature profile accompanied with the water injection can be clearly illustrated. 3 refs., 7 figs.

  18. Cooling characteristics of light and heat composite panel; Hikari{center_dot}netsu fukugo paneru no rekyakutokusei

    Energy Technology Data Exchange (ETDEWEB)

    Machida, Satoshi [Science University of Tokyo, Tokyo (Japan)

    1999-07-31

    The Japan Solar Energy Soc. encouraging prize is really thank you this time receiving. Present winning prize is regarded as becoming large self-confidence and further encouragement in advancing the research in future. Duplicates and resources energy depletion problem and environmental problem, etc. will become serious more and more in respect of the twenty-first century just before. It is the threat even in the inside on the increase of the electric power demand by the popularization of air conditioner, etc., and peak shaving of the electric power, etc. must be urgently carried out. We heavily carry out the research of catching, width shot heating and cooling panel constituted by the thermo device module and light and heat composite panel which combined photovoltaic power generation panel in respect of this problem. The development of this panel was solved with the purpose this time, we produce the test equipment experimentally in outdoors, and the data was acquired. As the result, though it is possible to obtain the case in which it operated as air-cooling this panel, and temperature gradient of largest 6 degrees C, and it is the analysis, and it 4s, when it was used in July, It was possible to obtain 4.2 degrees C mean temperature difference. It is the place which has installed improved light and heat composite panel in which we suggested afterwards trial and error at present in the roof. And, it will become also reporting schedule on heating characteristics of this panel in future. Though it consists finally, everybody of Komatsu central laboratory, who received support, when this study was carried out, is asked for the slender face, the attention of thanks is shown. (translated by NEDO)

  19. Effect of sunlight, transport and storage vessels on drinking water ...

    African Journals Online (AJOL)

    Effect of sunlight, transport and storage vessels on drinking water quality in rural Ghana. ... on drinking water quality in rural Ghana. K Obiri-Danso, E Amevor, LA Andoh, K Jones ... Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  20. Effect of organic matter, irrigation and soil mulching on the nutritional ...

    African Journals Online (AJOL)

    Rukevwe S. Abraka

    2016-11-30

    Nov 30, 2016 ... necessary for the soil humidity to be in an adequate amount (Danso ... clay, with soil and particle density of: 1.51 and 2.76 g cm-3, respectively ..... fertilization and irrigation methods on nitrogen uptake, intercepted ŷ = 2373.4 + ...

  1. Browse Title Index

    African Journals Online (AJOL)

    Items 251 - 300 of 366 ... S N Anyanwu. Vol 63, No 4-6 (2017), Stepwise minimal debridement in Fournier's gangrene: a technical note, Abstract. M.C. Kabeya, A Danso, L Gwanzura. Vol 46, No 9 (2000), Storage of breast milk: effect of temperature and storage duration on microbial growth, Abstract. E O Igumbor, R D Makura, ...

  2. A Pub/Sub Message Distribution Architecture for Disruption Tolerant Networks

    Science.gov (United States)

    Carrilho, Sergio; Esaki, Hiroshi

    Access to information is taken for granted in urban areas covered by a robust communication infrastructure. Nevertheless most of the areas in the world, are not covered by such infrastructures. We propose a DTN publish and subscribe system called Hikari, which uses nodes' mobility in order to distribute messages without using a robust infrastructure. The area of Disruption/Delay Tolerant Networks (DTN) focuses on providing connectivity to locations separated by networks with disruptions and delays. The Hikari system does not use node identifiers for message forwarding thus eliminating the complexity of routing associated with many forwarding schemes in DTN. Hikari uses nodes paths' information, advertised by special nodes in the system or predicted by the system itself, for optimizing the message dissemination process. We have used the Paris subway system, due to it's complexity, to validate Hikari and to analyze it's performance. We have shown that Hikari achieves a superior deliver rate while keeping redundant messages in the system low, which is ideal when using devices with limited resources for message dissemination.

  3. On the fault system and basement structure in and around the epicentral region of the 1995 Hyogo-ken Nanbu earthquake; 1995 nen Hyogoken nanbu jishin shingen shuhen no danso kiso kozo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Yokokura, T; Kano, N; Yamaguchi, K; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Ikawa, T; Ota, Y; Kawanaka, T [Japex Jeoscience Institute, Tokyo (Japan)

    1996-05-01

    A reflection elastic wave seismic survey was carried out as part of the emergency survey of active faults in relation with the Hyogo-ken Nanbu Earthquake. This paper presents an interim report on the survey covering a wide area with deep structure as the survey object. The paper mentions that processing the survey data has been nearly completed, and is in the stage of making analyses and interpretations of the result of the processing, and that the survey was an attempt of making a unified survey over land areas, shallow sea areas, and seas by setting twelve traverse lines in and around the epicenter region. The paper also introduces briefly what has been found on hypocenters used, vibration receivers, vibration intervals, and CPD intervals, and on shapes of faults, particularly the continuity (the relationship of the Ashiya fault, Koyo fault and Osaka bay fault with the above two faults, branching of the Osaka bay fault, faults between the Wada promontory fault, Awaji Island and the Osaka bay fault, the fault off the east coast at the central part of Awaji Island, the Shichiku fault on the west coast of Awaji Island, and the basement fault). Mention is given also on the basement structure chart of the Osaka bay prepared preliminarily for the purpose of reference. 2 figs.

  4. Excitation of tsunami by a pure strike-slip earthquake. ; Izu Oshima kinkai earthquake tsunami on Feb. 20, 1990. Yokozure danso jishin ni yoru tsunami no reiki. ; 1990 nen 2 gatsu 20 nichi Izu Oshima kinkai jishin tsunami

    Energy Technology Data Exchange (ETDEWEB)

    Abe, K. (Nippon Dental University, Tokyo (Japan). Niigata Junior College); Okada, M. (Meteorological Research Institute, Tsukuba (Japan))

    1993-06-24

    A numerical experiment was performed to reproduce the tsunami from the Izu-Oshima Kinkai Earthquake which occurred on February 20, 1990, using a tsunami excited by a pure strike-slip fault. An existence of a vertical fault with a length of 15 km and a width of 12 km was hypothesized in the south-north direction on the ocean bottom around the focal region. Then, a tsunami was assumed to have been excited when the fault was given a side-slip movement to create discrepancies of 1 m in the fault. Water level change for one hour after onset of the tsunami was calculated in one-second interval in each unit square with a side length of 1 km over an ocean area of 200 km from east to west and 150 km from north to south centering on the wave source. The results obtained from the calculation were harmonious with tsunami waveforms observed at five stations in the subject region and their spectral analytic results. Reproduced were the two predominant frequencies commonly observed at more than two stations, and difference in predominant cycles that appear according to azimuths of the observation points to the epicenter. These facts endorse the reasonability of the above hypothesis. 9 refs., 11 figs.

  5. Fault-related-folding structures and reflection seismic sections. Study by seismic modeling and balanced cross section; Danso ga kaizaisuru shukyoku kozo no keitai to jishin tansa danmen. 2. Seismic modeling oyobi balanced cross section ni yoru study

    Energy Technology Data Exchange (ETDEWEB)

    Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    It occasionally happens that there exists a part where reflection near the thrust is not clearly observed in a thrust zone seismic survey cross section. For the effective interpretation of such an occurrence, the use of geological structures as well as the reflected pattern is effective. When the velocity structures for a fold structure having a listric fault caused anticline (unidirectionally inclined with a backlimb, without a forelimb) and for a fault propagation fold are involved, a wrong interpretation may be made since they look alike in reflection wave pattern despite their difference in geological structure. In the concept of balanced cross section, a check is performed, when the stratum after deformation is recovered to the time of deposition, as to whether the geologic stratum area is conserved without excess or shortage. An excess or shortage occurs if there is an error in the model, and this shows that the fault surface or fold structure is not correctly reflected. Positive application of geological knowledge is required in the processing and interpreting of data from a seismic survey. 6 refs., 6 figs.

  6. Fault-related-folding structure and reflection seismic sections. Construction of earth model using balanced cross section; Danso ga kaizaisuru shukyoku kozo no keitai to jishin tansa danmen. 1. Balanced cross section wo mochiita chika model no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Tamagawa, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Pre-stacking depth migration treatment is studied for the estimation of the fold configuration from seismic survey cross sections. The estimation of a velocity structure is necessary for the execution of such treatment, and the utilization of structural-geological knowledge is required for its interpretation. The concept of balanced cross section in relation to the fault-bend fold constructs a stratum structure model under conditions that the deformation during fold and fault formation is a planar strain, that there is no change in volume due to deformation, and that a fold is a parallel fold. In addition to the above geometric and kinetic approach, there is another fold formation process simulation model using a Newtonian fluid for study from the viewpoint of dynamics. This simulation stands on the presumption that the boundary contains a ramp that had been in presence before fold formation and that an incompressible viscous matter is mounted on the top surface. The viscous matter flows and deforms for the formation of an anticline on the ramp. Such enables the reproduction of a fault-bend fold formation process, and helpful discussion may be furthered on the dynamic aspect of this simulation. 5 refs., 4 figs.

  7. International activities on research and production in ceramics. ; Development of overseas business-optical fiber. Kenkyu kaihatsu, seisan katsudo no kokusaika. ; Hikari faiba no kaigai seisan

    Energy Technology Data Exchange (ETDEWEB)

    Egami, K. (Corning International K.K., Tokyo (Japan))

    1994-04-01

    Researchers of the Corning Glass Works have made great contribution to the development of practical use of optical fibers. The effort of the Corning Glass Works in technological development and overseas production was introduced. Corning developed the outer vapor deposition (OVD) method suitable for large scale production. Later, the so-called vertical axial deposition (VAD) method was developed also in Japan, and a technology for quantity production of high quality optical fibers was established. The bases of the Corning's approach were respect for intellectual property and strategic market development, indicating that Corning had strategy for overseas production from the early stage (early stage of market growth) in addition to product supply strategy. Optical fiber is one of the strategic materials whose export is controlled in many countries, and the transfer of the related technology is also controlled. 1 fig.

  8. Investigational study of optical function materials for two-dimensional data processing; Nijigen joho shoriyo hikari kino zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper investigated/studied `space light modulation materials,` `dynamic hologram/memory materials,` `optical waveguide path materials,` etc. which become key materials in the high speed two dimensional processing. As to electrooptical materials proposed in this investigational study, the external electric field and the electric charges generated make quality of molecules themselves directly change to memory strong/weak signals of light. Therefore, the response velocity becomes less than a millionth of that of the liquid crystal display, and high speed which is needed for realtime moving image processing is anticipated. Hologram includes the phase information in addition to information on light strength. Therefore, it is a large capacity record medium and at the same time a record medium which can read/write two dimensional information as it is. With optical fiber, images cannot be transmitted as they are. Light waveguide path materials are those that accumulate roles of mirror and lens in a sheet of the material and construct a system which is strong in vibration, as optical parts connecting among materials for two dimensional data processing. 273 refs., 107 figs., 17 tabs.

  9. FY1995 ultra-high performance semiconductor lasers for advanced optical information network; 1995 nendo kodo hikari joho tsushinmo e muketa kyokugen seino handotai laser

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this research was to study and develop ultra-high performance semiconductor light source devices that should facilitate construction of advanced optical information networks. The semiconductor devices mentioned above are enhanced and integrated versions of distributed feedback (DFB) lasers based on 'gain coupling', which the group of the research coordinator has been investigating as a pioneer in the world. This research aimed at development of ultra-high performance semiconductor lasers that surpass the first generation conventional DFB lasers in any respect, by strengthening important device characteristics for system applications of the gain-coupled DFB lasers. The achievements of this research are listed below : 1. In-situ characterization of As-P exchange in MOVPE 2. Development of 1.55 {mu}m gain-coupled DFB lasers of absorptive grating type 3. Establishment of measurement technique for gain-coupling coefficients 4. Enlargement of small signal modulation response by the absorptive grating 5. Prediction of lower analog modulation distortion 6. Characterization of reflection-induced noise 7. Proposal and Demonstration of wavelength trimming 8. Proposal and Fabrication of GC DFB laser triode (NEDO)

  10. Light beam control by refractive index change in a modified purple membrane; Hen`i shimaku no kussetsuritsu henka wo riyoshita hikari bimu seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Takei, H.; Shimizu, N. [Hitachi Ltd., Tokyo (Japan)

    1996-04-01

    A purple membrane extracted from bacterial halobacterium salinarium is a membrane prepared by two-dimensionally crystallizing bacteriorhodopsin (bR) which is a photo-sensitive protein. When retinal chromophore in the bR absorbs photons, isomerization occurs, so that light cycle of bR comprising a light intermediate of different absorption spectrum occurs. Since this purple membrane has a high stability and a high repetition durability, a study of the application of the same to a rewritable holographic recording medium has been made in recent years. This paper describes an example in which the refractive index variation of a purple membrane the optical characteristics of which varies due to variation is applied to light beam control. The paper introduces a Fabry-Perot resonator as an optical element capable of carrying out light control by utilizing refractive index variation. The paper further describes the possibility of materialization of an optical logic comprising a combination of light-irradiation refractive index variation and a Fabry-Perot resonator and having nonlinear input/output characteristics such as the bistablity owing to the feedback effect in the resonator. 7 refs., 3 figs.

  11. Application of photo-excitation reaction on titanium oxide thin film for control of wettability; Sanka chitann hakumakujo no hikari reiki hanno no nuresei seigyo eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T.; Nakajima, A.; Hashimoto, K. [The Univ. of Tokyo, Tokyo (Japan); Takada, Y. [Kyushu Univ., Fukuoka (Japan)

    2000-03-31

    It is clarified that the photo-excitation hydrophilic reaction increasing wettability remarkably is induced by changing surface structure of titanium oxide radiated light. There are already many examples being in practical use of coating products applied hydrophilic reaction of titanium oxide surface such as drip-proof side millers for automobiles, self-cleaning building materials, and the like. When surface of titanium oxide having high activities for oxidisation and decomposition is coated organic materials and radiated light, wettability of surface changes as organic materials are decomposed. If it is possible to change wettability shaping pattern drastically by radiating light, the possibility of application for printing materials will be developed. After increasing contact angle by coating water and oil repellent on the titanium oxide thin film, images can be shaped by radiating light into pattern for changing surface of titanium oxide to be ultra hydrophilicity as decomposition of repellent. At that time, contact angle is 150 degree in water, 80 degree in oil, for not radiated aria, and is 0 degree in water and oil for radiated aria. Application for control technology of wettability keeps possibility of broader development to itself, not staying ability of self-cleaning and drip-proof. (NEDO)

  12. Photo-irradiation effects on GaAs atomic layer epitaxial growth. GaAs no genshiso epitaxial seicho ni okeru hikari reiki koka

    Energy Technology Data Exchange (ETDEWEB)

    Mashita, M.; Kawakyu, Y.; Sasaki, M.; Ishikawa, H. (Toshiba Corp., Kawasaki (Japan). Research and Development Center)

    1990-08-10

    Single atomic layer epitaxy (ALE) aims at controlling a growing film at a precision of single molecular layer. In this article, it is reported that the growth temperature range of ALE was expanded by the vertical irradiation of KrF exima laser (248 nm) onto the substrate for the ALE growth of GaAs using the metalorganic chemical vapor deposition (MOCVD) method. Thanks for the results of the above experiment, it was demonstrated that the irradiation effect was not thermal, but photochemical. In addition, this article studies the possibility of adsorption layer irradiation and surface irradiation as the photo-irradiation mechanism, and points out that coexistence of both irradiation mechanisms can be considered and, in case of exima laser, strong possibility of direct irradiation of the adsorption layer because of its high power density. Hereinafter, by using both optical growth ALE and thermal growth ALE jointly, the degree of freedom of combination of hetero ALE increases and its application to various material systems becomes possible. 16 refs., 6 figs.

  13. Development of new type of nonlinear optical materials with a function of ultrafast optical modulation; Chokosoku hikari reiki hencho kino wo motsu atarashii hisenkei kogaku zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sakaguchi, H. [Shizuoka University, Shizuoka (Japan). Research Institute of Electronics

    1995-12-15

    Ultrafast modulation of second harmonies from a Langmuir-Blodgett film consisting of a ruthenium complex was demonstrated for the first time. The mechanism of the modulator of SHG intensity on laser irradiation was ascribed to the change of molecular hyperpolarizability of the ruthenium complex on going from the ground state to the excited state. 9 refs., 12 figs.

  14. FY1995 research on nonlinear optical devices using super-lattice semiconductors; 1995 nendo chokoshi active hisenkei soshi wo mochiita chokosoku hikari seigyo gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose is to develop technologies on efficient generation and control of femtosecond optical pulses using a novel semiconductor optical devices. We studied a modelocked Cr:forsterite laser pumped by a diode pumped Nd:YVO4 laser. Both Kerr lens mode locking and semi-conductor saturable absorber initiated mode locking have been achieved. The minimum pulse width for pure Kerr lens mode locking is 26.4 fs, while for the semiconductor saturable absorber initiated mode locking, the pulse width is 36 fs. The latter is very resistant to the environment perturbations. We also present the measured dispersion data for the forsterite crystal and the SESAM, and discuss the dispersion compensation technique. (NEDO)

  15. Development of optical interference-type micro accelerometer for subsurface microseismic measurement; Micromachining ni yoru chika danseiha keisoku no tame no hikari kanshogata kasokudo sensor no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hirata, K; Niitsuma, H; Esashi, M [Tohoku University, Sendai (Japan). Faculty of Engineering

    1997-10-22

    Manufacture is under way of an optical interference-type micro accelerometer making use of the micromachining technology and an optical fiber measuring system for detecting microseismic waves in the ground. The sensor is required to be capable of detecting acceleration 0.1-1gal in amplitude, to be flat in amplitude characteristic in a frequency range of 10Hz-several kHz, to be ensured of straight phase characteristics to enable the measurement of transient phenomena, to be low in cross sensitivity, and to be high in resistance to water, pressure, and heat. The sensor is constructed in the following way. In the process for treating silicon, anisotropic etching is performed for the formation of a gap between the fiber end face and oscillator, boron is diffused, a stopper is formed, and then the silicon is subjected to penetrating etching. In the process for the optical fiber section, an optical fiber is inserted into a glass tube and fixed by an adhesive agent, and then the glass tube end face is polished, this together with the fiber end. Indium-tin oxide is sputtered onto the glass tube end. Finally, the sensor is assembled. 5 refs., 4 figs., 1 tab.

  16. Achievement report on research and development in fiscal 1989. Research and development of non-linear photoelectron materials; 1989 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective to realize the communication and information processing utilizing the high velocity and parallelism of light, search for materials having non-linear susceptibility and high-speed responsiveness, and research and development of the material using technology have begun. This paper reports the achievements in fiscal 1989. In developing organic materials, investigations and preliminary experiments were performed on three-dimensional non-linear photoelectron materials of organic low molecular systems, such as chiral non-linear photoelectron material. Fundamental studies were made on growth of orientation controlled crystals. Researches were carried out on polymeric films of organic and conjugate systems. In developing the dispersed system materials, researches were executed on a technology to deposit CuCl particulates using the air phase method and porous glass impregnation method, and on evaluation of non-linear photoelectron properties of CuCl particulate dispersed glass. In addition, glass dispersed system materials were studied by using the sol-gel method, the ultra-low melting point glass method, and the ultra quenching method. Furthermore, for the organic dispersed system materials, synthesizing conditions were discussed on CdS/polymer dispersing element films, and ultra-particulate synthesizing experiments were performed. In developing the ultra-grid system materials, researches were performed on the organic ultra grid making technology and the three-dimensional ultra-structuring technology. (NEDO)

  17. Photocatalytic removal of nitrogen oxides from ambient air using solar energy; Taiyo energy wo riyoshita taikichu no NOx no hikari shokubai jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Fukaya, M; Taoda, H; Watanabe, E; Nonami, T; Iseda, K; Kato, K [National Industrial Research Institute of Nagoya, Nagoya (Japan); Kunieda, S [NGK Insulators, Ltd., Nagoya (Japan); Kato, S

    1997-11-25

    Experiment was made on removal of NOx from ambient air using ceramic blocks coated with a newly developed easy-to- handle TiO2 film photocatalyst. After TiO2 sol was prepared by hydrolyzing titanium tetraisopropoxide, the photocatalytic blocks were prepared through drying and sintering after immersing the blocks in TiO2 sol. The effect of the number of coating on catalytic performance was studied using the single-coated and triple-coated blocks. Artificial solar light of 1mW/cm{sup 2} was used as light source for flowing reaction experiment of air (containing NOx) in a laboratory. NOx concentration rapidly decreased with irradiation, and 94% and 98% of NOx were removed by the single- and triple-coated blocks, respectively. NOx was completely oxidized to HNO3 through NO2 by triple-coated blocks. The demonstration test of removal of NOx from ambient air in Okazaki city showed a removal rate of nearly 90% in noonday and 40% or more in average, while not 0% but 5-20% even in the nighttime. The latter is probably derived from adsorption by the porous photocatalytic blocks. 2 figs., 4 tabs.

  18. Control method for light deterioration of amorphous solar cell. 2. Temperature effect method; Amorphous taiyo denchi no hikari rekka yokuseiho. 2. Ondo kokaho

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H; Itsumi, J; Sano, N [Kumamoto Institute of Technology, Kumamoto (Japan)

    1997-11-25

    Experimental studies have been carried out on suppressing early deterioration in amorphous silicon solar cells. The amorphous silicon solar cell is characterized by deterioration due to light irradiation and restoration due to temperature rise. An exposure experiment was performed under three conditions: installation in natural environment, installation with rear side of the solar cells covered with an insulating material, and installation with rear side of the solar cells covered with warming elements and an insulating material. Tests were made on suppressing progress of the early deterioration caused by temperature conditions. As a result, the efficiency in the natural condition was found to decrease as largely as 32% in an open circuit condition and 58% in a short circuit condition. The efficiency reduction rate was smaller in the open circuit condition when the insulation material was installed, but in the short circuit condition, resistance characteristics caused by rain water and electrolytic corrosion were exhibited. For the case with warming elements installed, the reduction in the efficiency was more remarkable, contrary to the expectation. The cause was determined that water existing between the rear side and the warming elements was warmed up, accelerating the electrolytic action, and resulting in deterioration advanced over a wide area in the rear side. 6 refs., 6 figs., 3 tabs.

  19. Chromatic regulation in cyanobacterium as studies by HPLC quantitation of photosynthetic pigments. Kogosei shikiso no HPLC teiryo ni motozuku ranso no hikari tekio process tsuiseki

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, H.; Watanabe, T. (The Univ. Tokyo, Tokyo (Japan). Inst. of Industrial Science)

    1991-08-01

    Plants higher than Cyanobacterium have two kinds of resction centers(RC) which convert photon energy to a flow of electrons and whose photosensitive spectral regions are slightly deviated from each other. In the photosynthetic process, the ratio of numbers between these two kinds of reaction centers is adaptively varied so as to allow the overall flow of electrons to proceed in a well-balanced manner. It is important to rapidly and exactly determine the ratio of RC numbers between the two photochemical systems in order to investigate such photoadaptive process. The report describes the quantitative determination using high performance liquid chromatography(HPLC) for this purpose. Pigments were extracted from Cyanobacteria which are in different adaptive processes brought by being cultured in the environments differing in the quantity of light or in the environment of varying quantity of light, and subjected to quantitave determination in consideration of the fact that the reaction centers, I and II, have the respective special kinds of chlorophyl derivatives Chl-a, Chl-a{prime}. As the results, it was confirmed that validity can be given to the estimation of the numbers of reaction centers in terms of the quantities of Chl-a and Chl-a prime and the proposed method is drastically faster and simpler than the conventional methods. 14 refs., 5 figs..

  20. FY1995 fundamental study of imaging simulator for diagnostics and therapeutics using light; 1995 nendo hikari wo riyosuru shindan chiryoyo gazo simulator no kiso kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Medical application of lasers is rapidly expanding in accordance with the development of laser technology. However, it is difficult to predict how light propagates and is absorbed by living bodies because of strong scattering of light by biological tissues. Therefore, the determination of light dose has been based on experience. This fundamental study aims to develop a imaging simulator which can predict propagation of light and its effectiveness in medical diagnostics and therapeutics. Teoretical models of light propagation in biological tissues have been constructed, and experiments have been conducted to validate the theoretical calculation. In the theoretical calculation, a three-dimensional model which simulates a human head with five layers of different tissue types. Numerical calculation has been done by using the finite element method to simulate the propagation of ultrashort pulse light, and it is shown by a computer graphics technique for the first time in the world. In the experiment, a solid phantom which anatomically and optically simulates a human head based on MRI images has been fabricated by using the optical prototyping technology for the first time in the world again. Also, we have compared the experimental results of the transmitted light through the solid phantoms with the theoretical results and have succeeded in reconstructing the tomographic images of optical properties. (NEDO)

  1. Control method for light deterioration of amorphous solar cell. Temperature effect method; Amorphous taiyo denchi no hikari rekka yokuseiho. Ondo kokaho

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H.; Yokoyama, S.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

    1996-10-27

    This paper describes a proposed method for suppressing light deterioration (temperature effect method), in which an annealing effect was always expected by laminating an NEM element and a heat insulation material on the back side of a-Si solar cell module and thereby raising the temperature in the back side of the module, and also describes an outdoor exposure test device completed for the method. The NEM element consisted of conductive potassium titanate and high molecular polymer and was a self temperature-controlling organic exothermic body that required no outside temperature control device. It was provided with a heat generating temperature of 45-75{degree}C as the exothermic property of the element and capable of generating heating temperature arbitrarily according to the purpose. The NEM element varied a resistance value against the ambient temperature and kept the element temperature constant. Measurement was commenced starting April 19, 1996, using the completed outdoor exposure test device and a measuring circuit. The deterioration phenomenon was and from then on continuously examined under the following conditions: (1) measurements were those of clear days only, and (2) measurements to be used were those between 10:00 and 14:00 with the quantity of solar radiation on a constant level. 4 refs., 4 figs., 1 tab.

  2. Performance analysis on borehole energy storage system including utilization of solar thermal and photovoltaic energies; Taiyonetsu hikari riyo wo fukumu borehole energy chozo system no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T [Tohoku University, Sendai (Japan); Yamaguchi, A [Matsushita Electric Co. Ltd., Osaka (Japan)

    1996-10-27

    A permanent borehole energy storage system utilizing solar energy and waste heat from coolers is simulated, to be used as an air conditioning system for super-tall buildings. A 100m-long pipe is buried vertically into the ground, and a heat medium is caused to circulate in the pipe for the exchange of heat with the soil. Thirty borehole units are used, each measuring 9m{times}9m (with the pipe pitch being 3m). Solar cells occupying half of the wall surface facing south and solar collectors installed on the roof supply electric power and heat for cooling and warming. Heat in the ground is transferred mainly by conduction but also is carried by water and gas in movement. So, an analysis is carried out using an equation in which heat and water move at the same time. Because waste heat from cooling and warming systems is accumulated in the ground and none is discharged into the air, big cities will be protected from warming (from developing heat islands). As compared with the conventional boiler-aided air conditioning system, a hybrid borehole system incorporating solar collectors and solar cells will bring about an 80% reduction in CO2 emission and annual energy consumption. 7 refs., 3 figs., 4 tabs.

  3. Optimum design of composite panel with photovoltaic-thermo module. Absorbing effect of cooling panel; Hikari netsu fukugo panel no saiteki sekkei. Reikyaku panel no kyunetsu koka

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M; Kikuchi, S; Tani, T [Science University of Tokyo, Tokyo (Japan); Kadotani, K; Imaizumi, H [Komatsu Ltd., Tokyo (Japan)

    1996-10-27

    The composite panel with photovoltaic-thermo module becomes higher in energy-saving than the conventional air-conditioning system by the independent radiational heating and cooling effect obtained when the generating panel using a solar cell module is combined with the heating and cooling panel using a thermo-element module. The output of a solar cell module can be directly used because the solar cell module operates in AC. This paper reports the relation between the absorbed value and power consumption of the cooling panel, while paying attention to the cooling panel. The performance coefficient of the maximum absorbed value from an non-absorbing substance to a cooling panel is 2 to 3. Assume that the cooling panel during non-adiabatic operation is operated using a solar cell module of 800 W/m{sup 2} in solar intensity and 15% in conversion efficiency. The cooling-surface temperature difference is 12.12 K, and the maximum absorbed value of a non-absorbing substance to a cooling panel is 39.12 W/m{sup 2}. The absorbed value of the outer temperature to the cooling panel is 74.4 W/m{sup 2}, and each performance coefficient is 3.26 and 0.62. The absorbed value must be calculated for evaluation from the cooling-surface temperature difference measured directly from the cooling panel. 4 refs., 8 figs., 1 tab.

  4. Current status and prospect on photo-catalyst application in environmental problems; Kankyo mondai ni okeru hikari shokubai oyo no ganjo to tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T. [Toto Ltd., Kitakyushu (Japan)

    1995-09-30

    This paper summarizes application of photo-catalysts in environmental problems. The paper lists examples of the application in residential environments. Photo-catalytic decomposition is possible by using ultraviolet rays contained in room illumination if the bacterial presence is sparse. The examples thereof may be cited as follows: if colon bacilli are suspended on a tile with TiO2 photo-catalyst sintered in it and exposed to room illumination, the bacteria are disinfected; using photo-catalysts in a bathroom suppresses deposition of Pseudomonas aeruginosa; a photo-catalyst tile (TiO2 loaded with Cu) and light irradiation reduce intensity of tobacco smoke odor; and adsorbents may be used simultaneously if intermediate products are odor generating substances. The examples of applying photo-catalysts to regional environments may be quoted as follows: growth of algae in a Petri dish is suppressed by presence of Cu loaded TiO2 under room illumination; this leads to an expectation on its effect in a relatively clean water environment; glass beads loaded with a TiO2 photo-catalyst placed in a gold fish breeding tank reduces turbidity, the number of colon bacilluses, and COD value; and the mortality in gold fish shows no change. With an objective of application to exterior building materials, photo-catalyst applied tiles were left outdoors for 160 days. Nitric acid ions were detected that are thought to have been generated by decomposition of microorganisms that have deposited on the tiles. 6 refs., 5 figs., 3 tabs.

  5. Studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; Handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, H; Sona, S; Koike, H; Hori, H; Negishi, N; Kohara, H; Ibusuki, A [National Institute for Resources and Environment, Tsukuba (Japan); Vakhtin, A; Borovkov, V [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    Studies are made to define the working mechanism of semiconductor photocatalysts such as TiO2 and to establish designing guidelines for improving on their activity and functions. TiO2 in the air actively produces oxygen seeds for the oxidation and removal of NOx, etc. It is desired that a catalyst have a specific surface area large enough to retain the product of its action. To meet the need, a thin-film photocatalyst which is an aggregate of TiO2 crystals is produced by burning a film of a sol/gel system of reaction doped with macromolecules. This product has a larger specific surface area and is higher in pollutant-removing performance, and may be put into practical use. In another experiment, metal-carrying particles TiO2 suspended in water are employed for the reduction of CO2. Though the main product of catalysts carrying Pt or Pd is methane, a photocatalyst carrying RuO2 produces acetic acid mainly and loses less activity with the passage of time. A hybrid photocatalyst is composed of an organic pigment and inorganic semiconductor, synthesized through a covalent bond between a sililated-surface thin TiO2 film and porphyrin. It is confirmed that the newly developed process brings about an increase in electron migration efficiency. 3 figs.

  6. Method of measurement of near tip field of fast propagating cracks by means of interferometry; Hikari kansho ni yoru kosoku shinten kiretsu sentanbu no oryokuba keisokuho

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, s.; Miyazaki, F. [Toyohashi University of Technology, Aichi (Japan); Nakane, K. [Nitto Denko Corp., Osaka (Japan)

    1994-12-15

    The measurement by an interference method at the tip of fast propagating cracks was investigated. To clarify the direction-dependent problem of dynamic cracks in a higher-order term, a high-precision stress field must be measured in every direction. In this method, the propagated interference fringes near the crack tip are shot at a speed of some hundreds of m/sec, and the coefficient of dynamic stress extension is obtained from the expression given when the number of fringes (`m`) in the interferences fringes is differentiated partially. The information below was obtained. The stress field in every direction can be analyzed by the interference method. However, the interference fringes in an area of absolute {theta} < 120{degree} are radially spread from the crack tip, so the precision of the interference fringes in the {gamma} direction deteriorates. In this area, the above partial differential is higher in precision when {alpha}m/{alpha}{theta} is used instead of {alpha}m/{alpha}{gamma}. The stress extension coefficient obtained by a caustic method can be verified if a stress field of {theta} = {plus_minus}72{degree} is analyzed by the interference method. By shooting in this optical system, the COD measurement, the K-value measurement of caustic light, and the stress field measurement by an interference method can be done simultaneously. 17 refs., 11 figs.

  7. Development of metal complexes which has a novel type of dhotocatalysis activity; Shinki hikari shokubai tokusei wo yusuru kinzoku sakutai no sousei

    Energy Technology Data Exchange (ETDEWEB)

    Ishitani, Osamu [Saitama University, Saitama (Japan). Graduate School of Sceince and Engineering

    1999-12-16

    Purpose of this research are (1) development of photocatalysts which selectively drive hydride transfer and (2) their application to the enantioselective reduction of an unsaturated substrate. photocatalysis of [Ru(bpy){sub 2}(py){sub 2}]{sup 2+} (1) and [Ru(tpy)(bpy)(py)]{sup 2+} (2) (bpy=2,2'-bipyridine, tpy=2,2' : 6',2' '-terpyridine, py=pyridine) for reduction of unsaturated compounds was investigated using triethylamine as a reductant. Formation of the hydrogenated compounds was observed but the corresponding one electron reduced compounds were not detected at all. The complex 1 photocatalysed the reduction of trifluoroacetophenone (5) and gave the alcohol in a 67% yield but 2 gave only a 27% yield. The reaction proceeds via the photosubstitution of a py ligand of the ruthenium complex, followed by photochemical formation of the hydride complex. The ruthenium hydride complex reacts with 5 to give [Ru(tpy)(bpy)(OCHPhCF{sub 3})]{sup +} (4). Dissociation of 4 to the alcohol was not efficient and the yield was 10%. (author)

  8. Optical fiber taste sensors using potential sensitive dye coatings. Makuden'i kanjusei shikisomaku wo mochiita hikari fiber mikaku sensor

    Energy Technology Data Exchange (ETDEWEB)

    Yamakawa, S.; Yamaguchi, A. (Toyama National College of Maritime Technology, Toyama (Japan))

    1992-12-20

    The present paper proposes a new taste recognition system using optical response patterns from multi-channel optical fiber sensors having potential sensitive dye coatings. It was found that the sensors give large changes in optical absorption spectra of the dyes when they are immersed in various taste solutions. Consequently, it was shown that the sensors can be used as a taste sensor. Six dyes, which give large changes in dye absorption, were selected from twenty dyes and used for six-channel optical fiber taste sensors array. The absorption spectra change data were processed by multiple discriminant analysis and neural networks using back-propagation algorithm. From the analytical results, it was demonstrated that salty (NaCl), bitter (quinidine), sweet (sucrose), sour (HCl), and umami (sodium glutamate) substances can be recognized from each other by using the optical taste sensor system. 11 refs., 8 figs., 2 tabs.

  9. Report on achievements in fiscal 1988 on research and development of the photoreactive materials under the next generation basic technology research and development project. Comprehensive surveys and researches on photoreactive materials; 1988 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokuksho. Hikari hanno zairyo sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    This paper describes the achievements in fiscal 1988 on comprehensive surveys on photoreractive materials. Based on the research and development institution for the next generation basic technology under the initiative of the Agency of Industrial Science and Technology, development is being promoted on photoreactive materials, or photochromic materials and photochemical hole burning (PHB) materials (materials in which molecular structures and assembly state can be changed reversely by actions of light, leading to expectation of application thereof to ultra-high density recording, displays at high resolution, and light switches). In order to achieve smooth and efficient promotion of the development thereof, development of the related technologies inside and outside the country was surveyed and discussed. Comprehensive surveys and researches were also carried out on the common basic technologies by looking to the well-informed people for guidance on the research. This fiscal year has held joint committee meetings to which lecturers were invited to discuss respective problems in the research and development trends. In addition, as the domestic survey, the status of research and development at the Tsukuba University was surveyed on photo-responsive polymeric gels. Furthermore, as the survey on the overseas technological trends, information related to photoreactive materials was collected mainly on photochemical burning materials in the U.S.A., and the research trends were surveyed. (NEDO)

  10. Direct-semidirect (DSD) codes

    International Nuclear Information System (INIS)

    Cvelbar, F.

    1999-01-01

    Recent codes for direct-semidirect (DSD) model calculations in the form of answers to a detailed questionnaire are reviewed. These codes include those embodying the classical DSD approach covering only the transitions to the bound states (RAF, HIKARI, and those of the Bologna group), as well as the code CUPIDO++ that also treats transitions to unbound states. (author)

  11. Kinetic analysis of photochemical sterilization of thermoduric bacterial spores in slurry of semiconductor catalyst particles with aeration. Handotai shokubai ryushi no tsuki kendakukei ni okeru tainetsusei saikin hoshi no hikari sakkin to sono sokudoronteki kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Tone, S; Taya, M; Kato, S; Horie, Y; Ashikaga, Y [Osaka Univ., Osaka (Japan). Faculty of Engineering and Science; Joo, Hyunkyu [Konkuk Univ., Seoul (Korea, Republic of)

    1993-11-10

    To study the utilization of the photochemical sterilization of thermoduric bacterial spores B. stearothermophilus with photocatalysis of TiO2 particles, light irradiation experiments are conducted under various operational conditions. TiO2 particles and dissolved oxygen resulting from aeration must coexist to accelerate the rate of spore sterilization under light irradiation of a high pressure mercury lamp. The sterilization rate increases with larger average light intensity in the reactor, and it is estimated that the dissolved oxygen contributes to the formation of oxidative radicals which become the attacking species. The maximal rate of spore sterilization is obtained under the condition of TiO2 concentration of 5[times]10[sup -2]kg[center dot]m[sup -3]. By combining a second-order rate equation, wherein the spores' death caused by the oxidative radicals formed by TiO2 photocatalysis is taken into consideration, and single-hit multitarget model, wherein the target damaged by the oxidizer in the spores is assumed, the sterilization velocity can be described well, and the effect of light intensity and the obtained rate parameters are correlated well. 13 refs., 7 figs., 3 tabs.

  12. FY1995 studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; 1995 nendo handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Development of the semiconductor photocatalyst such as titanium dioxide is important for photo-energy conversion and purification of the environment. We make clear that the mechanism of the photocatalysis using a spectroscopic or physico-chemical methods, and we developed the new photocatalyst with the control of the surface area, porosity, infinitesimal content, and surface modification of the catalyst surface. Titanium dioxide thin film photocatalysts were prepared by the dip coating method. Surface structure of the thin film was formed by the aggregated TiO{sub 2} anatase particle, its size was around 5 nm. This thin films effectively oxidazed NO, its photocatalytic activity is higher than that of commercial photocatalyst. Metal oxide anchored TiO{sub 2} photocatalysts (RuO{sub 2}/TiO{sub 2}) were prepared by the co-precipitation method. Effective charge separation of the RuO{sub 2}/TiO{sub 2} were confirmed by the measurement of ESR. The RuO{sub 2}/TiO{sub 2} photocatalyst successfully reduced CO{sub 2} and preserved its activity for much longer period than metal loaded catalyst. Hybrid photofunctionalized material was prepared by anchoring porphyrin moieties on the titanium dioxide surface. The relative quantum yield of electron transfer from porphyrin to the titanium dioxide conduction band has been markedly increased by water treatment of quanternized porphyrin-titanium dioxide covalently linked systems owing to removal of adsorbed porphyrin domains. (NEDO)

  13. FY1995 study of electronic coservice project which used Optical-Smart Hybrid Card; 1995 nendo hikari IC hybrid card wo mochiite katei kara ukeru gyosei denshika service project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As one of advanced multi media service, We can think about electoronization-network changing of the public coservice. that the official system provides. It can be expected to improve the life environment for a nation by the electronization. The purpose of this research is to clarify the off-line administration of an individual information and the issue on security. We constructed the experimental system using the Internet and Optical-IC hybrid card that an individual information is administrated. The system provides the following services. (1) On-stop moving service (2) Electronic certificate publishing service (3) Electronic ticket publishing service We have mounted client terminals at Fuchu city hall, Yokohama city hall, and Keio University, and made field experimentation. (NEDO)

  14. Fiscal 2000 survey report. Research on laser-aided photolysis of environmental pollutant in liquid phase system; 2000 nendo ekisokei ni okeru kankyo osen busshitsu no laser hikari bunkai gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Experiments were conducted on laser-aided decomposition and removal of chemical substances in liquid phase systems on the assumption that there existed chemical pollutants in wastewater or water after washing burned ash. The aim of the research was to split carbon-chlorine bonds and break benzene rings, the two being the cause of harmfulness, and experiments were conducted using chlorophenol. The photolytic lasers were ArF excimer laser and KrF excimer laser. It was found that the reduction rate of chlorophenol in a water solution under excimer laser irradiation was 1.7 times higher under KrF laser than under ArF laser. For mediums other than water, isopropanol was used, more convenient than chlorophenol in separating organic pollutants from burned ash and the like. In this case, organochlorine compounds were generated at the beginning, but they disappeared when irradiation was prolonged. It was demonstrated that the laser-aided environmental cleaning technology would find a very wide scope of application as an effective photolytic means. (NEDO)

  15. Pressure dependence of emission intensity of rare-gas excimer light produced by silent discharge; Teikiatsu ryoiki ni okeru musei hoden reiki ki gas excimer hikari shutsuryoku no atsuryoku izonsei

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Y.; Tanaka, M.; Yukimura, K. [Doshisha University, Kyoto (Japan)

    1996-09-20

    To establish the pressure dependence of silent discharge excited rare gas excimer light emission, a vacua ultraviolet light was subjected to spectroscopic analysis at a pressure lower than 20kPa. Researches are under way to apply the discharge excited rare gas excimer lamp as a vacuum ultraviolet light source for the development of new materials and for the conservation of environments. When the pressure is as low as 1.8kPa or 4.4kPa, the emission has peaks at wavelengths centering on 147nm and 149nm, both of which are the resonance lines of the xenon atom. Excimer generation becomes prominent as the pressure increases, with the second continuum of light growing dominant at 35kPa to weaken relatively the resonance lines and the first continuum of light. In the first continuum, emission increases only at a suppressed rate, as compared with emission in the second continuum, due for instance to a collision caused relaxation process in which excimers are lost. In the case of xenon in the vicinity of 10-11kPa, the first continuum of light and the second continuum of light are approximately equal in emission intensity, producing a vacuum ultraviolet light source with a bandwidth relatively large for a single gas spectrum. 14 refs., 11 figs.

  16. Low temperature formation of ferroelectric PbTiO3 films by laser ablation with 2nd laser irradiation; Reiki hikari laser heiyo laser ablation ho ni yoru kyoyudentai PbTiO3 usumaku no teion keisei

    Energy Technology Data Exchange (ETDEWEB)

    Tabata, H.; Kawai, T. [Osaka University, Osaka (Japan)

    1997-08-20

    The unique advantage of the pulsed laser deposition is its ability to produce highly oriented stoichiometric films at a low substrate temperature. Ferroelectric PbTiO3 thin films have been formed using 2nd laser assisted laser ablaion technique at low temperature, i.e., 350degC, on Sr7iO3 single-crystal substrates and Pt/MgO electrodes. The second laser irradiation at the substrate surface is quite effective for crystallization of the films at low substrate temperature below 400degC. The suitable energy density (fluence) of the irradiation laser is in the range of 30-100 mJ/cm{sup 2}. X-ray diffraction patterns of PbTiO3 thin films show c-axis orientation, with a rocking angle of 1.0 - 0.5deg. These films exhibit ferroelectric hysteresis loop. The dielectric constant and remanent polalyzation of the PbTiO3 films are in the range of 120-150 and 60-80 {mu}C/cm{sup 2}, respectively. 31 refs., 10 figs., 1 tab.

  17. 55th electric science promotion prize (progress prize). Demonstration of optical soliton transmission on OPGW first in the world; Dai 55 kai denki gakujutsu shinkosho (shinposho) jusho. Seiaihatsu no OPGW ni okeru hikari soriton denso no jissho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-10

    Electric science promotion prize (progress prize) is given to `Person who newly proposed a new concept, theory, material, device, system and method on electrical science and technology, or demonstrated these proposals` by the commendation committee of Institute of Electrical Engineers of Japan every year. Eight promotion prizes including that for Kansai Electric Power`s `Demonstration of optical soliton transmission on OPGW first in the world` were given. This research succeeded in development of the transmission/ receiving device suitable for optical soliton transmission, and the prediction method of an optimum transmission condition by computer simulation. In addition, this research succeeded in 10Gbit transmission of 784km and 40Gbit transmission (4-wave multiplex) of 392km by applying the above research result to Okurobe trunk line OPGW (98.2km). This demonstration of optical soliton transmission on OPGW is first in the world. (NEDO)

  18. Dependence of leaf surface potential response of a plant (Ficus Elastica) to light irradiation on room temperature; Shokubutsu (gomunoki) hamen den`i no hikari shosha oto no shitsuon izonsei

    Energy Technology Data Exchange (ETDEWEB)

    Ishii, H; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan)

    1997-11-25

    In order to clarify plant body potential information, study was made on a leaf surface potential response to light irradiation. The leaf surface potential change, total transpiration and transpiration rate of Ficus Elastica were measured using light irradiation period and room temperature as parameters. The leaf surface potential change shows a positive peak after the start of light irradiation, while a negative peak after its end. Arrival time to both peaks is constant regardless of the light irradiation period, while decrease with an increase in room temperature. Although the total transpiration increases with room temperature, this tendency disappears with an increase in light irradiation period. The transpiration rate shows its peak after the start of light irradiation. Arrival time to the peak is saturated with the light irradiation period of 60min, while decreases with an increase in room temperature. These results suggest that opening of stomata becomes active with an increase in room temperature, and the peak of the leaf surface potential after the start of light irradiation relates to the opening. 3 refs., 11 figs.

  19. Calculation of heat balance considering the reflection, refraction of incident ray and salt diffusion on solar pad; Hikari no hansha kussetsu oyobi shio no kakusan wo koryoshita solar pond no netsukeisan

    Energy Technology Data Exchange (ETDEWEB)

    Kanayama, K; Li, X; Baba, H; Endo, N [Kitami Institute of Technology, (Japan)

    1997-11-25

    In calculating heat balance of solar pond, calculation was made considering things except quality of the incident ray and physical properties of pond water which were conventionally considered. The real optical path length was determined from the reflection ratio of ray on the water surface based on the refraction ratio of pond water and the locus of water transmitted ray in order to calculate a total transmission rate. The rate of absorption of monochromatic lights composing of solar light in their going through the media is different by wavelength, and therefore, calculation was made in each monochromatic light. As to four kinds of salt water solution, NaCl, KCl, MgCl2 and CaCl2, these phenomena seen in solar pond are taken in, and a total transmission rate based on reality can be calculated by the wavelength integration method. Moreover, in the salt gradient layer, there are gradients in both concentration and temperature, and thermal physical values of each layer change. Accordingly, mass transfer and thermal transfer by both gradients were considered at the same time. An analytic solution was introduced which analyzes salt diffusion in the temperature field in the gradient layer and determines the concentration distribution. By these, concentration and physical values of each layer were calculated according to phenomena, and thermal balance of each layer of the solar pond was able to be accurately calculated. 6 refs., 5 figs., 2 tabs.

  20. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  1. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the mechanism of light deterioration reaction of photochromic molecules, it was disclosed that 6-nitrospirobenzopyran has the light deterioration caused from the excitation triplet state. This disclosure presents a possibility of preventing the light deterioration. New derivatives that show photochromism were synthesized, and thin films were produced by using the LB process. This indicates a possibility of producing the photochromic materials as the high multiplex recording material. With regard to PHB materials, an evaluation technology having spectrum resolution of the world's highest level was established and measurements were performed. Hole formation was verified for the first time in the world at the temperature higher than the liquid nitrogen temperature by using a PHB material of ionic porphin/polyvinyl alcohol systems. This verification indicates a feasibility of practically usable PHB materials. (NEDO)

  2. Kickoff into the future - Community full of light and balmy wind, Naraha. Regional new energy vision for Naraha Town; 2001 nendo Naraha machi chiiki shin energy vision. Mirai he no kick off - Hikari to kaze no machi Naraha

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for enhancing people's consciousness of such at Naraha Town, Fukushima Prefecture, surveys and studies were conducted involving the trend of energy consumption of the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The annual energy consumption of the town is 1,134,300 GJ, with industries consuming 41%, transportation 36%, households 12%, and commerce 11%. The energy comprised 76% from oil based fuels and 24% from electric power. Some new energy introduction projects were discussed, which covered the exhibition, public relations activities, and education through the use of wind power generation and photovoltaic power generation or solar heat utilization for Tenjin Point Sports Park, natural park surrounding the Kidogawa dam, on-the-road station Naraha Michinoeki, solar cars, and hybrid type street lamps; photovoltaic power generation, solar heat utilization, and clean energy vehicles for a special nursing home for elderly people, nursery schools, kindergartens, and a processing center for agriculture, forestry, and fishery products; and disseminating and enlightening activities conducted for people in general and business operators. (NEDO)

  3. Adaptability of drowsiness level detection that measures blinks utilizing image processing to changes in the ambient light; Hikari kankyo no henka ni tekiosuru kao gazo shori ni yoru inemuri unten kenchi

    Energy Technology Data Exchange (ETDEWEB)

    Kaneda, M; Obara, H; Nasu, T [Nissan Motor Co. Ltd, Tokyo (Japan)

    1997-10-01

    A drowsiness warning system that measures blinks utilizing image processing technology has a number of issues that need to be resolved. One issue is the adaptability of the system to changes in the ambient light environment in the actual vehicle interior. We have devised image processing software which is robust to changes in the ambient light. The drowsiness detection performance of the system was evaluated in laboratory tests and actual driving tests. It was found that the system can has a positive effect on detecting drowsiness level. 3 refs., 10 figs.

  4. Analysis of chromatic dispersion compensation by measuring time domain optical spectrum distribution of light pulse; Hikari pulse chu no hacho jikan bunpu sokutei ni yoru bunsan hosho gijutsu no hyokaho

    Energy Technology Data Exchange (ETDEWEB)

    Saito, M.; Kurono, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-05-01

    A large number of single mode fibers (SMF) for 1.3 {mu}m light are installed in electric power communication facilities. On the other hand, light of 1.5 {mu}m band is being used more in the capacity increasing technology to minimize transmission loss. If this is applied to the current SMF, waveform distortion is generated due to wavelength dispersion, thus the transmission speed and distance are limited. In order to evaluate quantitatively the effects of a wavelength dispersion compensating technology, a method was developed to derive time change in each wavelength component in light pulse. No sufficient wavelength separation is possible if permeation bandwidth of a wavelength filter is wider than the wavelength width of the light pulse. Therefore, a method was developed to derive time change in the wavelength components in the light pulse from small difference in the measured light waveforms after transmission when the central wavelength of a wavelength variable filter is varied. It was possible from comparing the method to derive the wavelength dispersion amount and the dispersion compensation amount. Since the method reveals simultaneously the distribution of strength against wavelength and time contained in light pulse, the method is advantageous in elucidating compensation limit and causes for compensation errors. The effectiveness of the method was verified by a 1.5-{mu}m light transmission test. 14 refs., 26 figs., 2 tabs.

  5. Study on solar chemical heat pump system. Basic experiment on dehydrogenation of 2-propanol using heteropoly-acid photo catalyst; Solar chemical heat pump no kenkyu. Heteropoly sankei hikari shokubai wo mochiita 2-propanol no dassuiso hanno

    Energy Technology Data Exchange (ETDEWEB)

    Doi, T [Electrochemical Laboratory, Tsukuba (Japan); T-Raissi, A; Muradov, N [Florida Solar Energy Center, FL (United States)

    1996-10-27

    With the purpose of converting solar heat energy to an industrial heat energy, an examination was carried out empirically on the case of using a heteropoly-acid photo catalyst for the decomposition reaction process of 2-propanol. The experiment was performed in Florida Solar Energy Center, in the U.S.A.. The device for the experiment was constituted of a reaction part, distribution manifold for feeding from the lower part of the reaction part a 2-propanol solution for which a photo catalyst was suspended, storage tank served also as a gas-liquid separating container, and circulating pump. Silica-tangstic acid was used as the photo catalyst. In an outdoor experiment using solar radiation, the quantity of inclined global solar radiation was 530-950W/m{sup 2} in clear days and 100-600W/m{sup 2} in cloudy days, with temperatures between 17 and 26{degree}C throughout the experiment period. In addition, an indoor experiment was also conducted using an artificial light source (UV light). As a result of the experiment, the energy conversion efficiency was at most about 1% of incident UV light, a low figure compared to a heat utilization ratio of approximately 15% with a thermal catalyst. 6 refs., 8 figs.

  6. Changes of the temperature coefficients of the characteristics which accompany degradation and recovery of a-Si solar cells; A-Si taiyo denchi no hikari (denryu) rekka oyobi kaifuku ni tomonau tokusei ondo keisu no henka

    Energy Technology Data Exchange (ETDEWEB)

    Yanagisawa, T; Koyanagi, T; Nakamura, K; Takahisa, K; Kojima, T [electrotechnical Laboratory, Tsukuba (Japan)

    1996-10-27

    Pursuant to the measuring of temperature dependency of the characteristics such as conversion efficiency, during the process of degradation in a-Si solar cells due to light and electric current and the process of recovery by annealing, this paper describes changes in temperature coefficients, correlation between the characteristic parameters and the degradation, and the results of the examination of their characteristics. The conversion efficiency {mu} degraded approximately by 45% of the initial value each by the irradiation under a light intensity with 3 SUN accelerated and by the infusion of current at 20mA/cm{sup 2}; and then, the efficiency recovered to 70-75% of the degradation by subsequent annealing. In addition, in the temperature dependency at 80{degree}C against at 20{degree}C, Isc slightly increased while Vcc greatly decreased. This slight increase in Isc was mainly due to the decrease in the width of the forbidden band, while the decrease in Vcc was due to the increase in the reverse saturation current. The temperature dependency of {mu}N was negative, becoming small in accordance with the degradation. The temperature dependency of FF/FFO was negative initially both in light and current, but it decreased with the degradation and turned to positive. The temperature coefficients of I-V parameters reversibly changed corresponding to the degradation and recovery of these parameters and stayed in a good correlation. 7 refs., 8 figs., 1 tab.

  7. Development of new technologies for high quality thin film and its application to energy engineering; Hikari seigyo to sokudo senbetsu ni yoru chokinshitsu usumaku no seisaku to energy bun`ya eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Hijikata, K; Inoue, T; Nagasaki, T; Suzuki, Y; Sato, I [Tokyo Institute of Technology, Tokyo (Japan); Nakabeppu, O [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1997-02-01

    This paper describes laser irradiation and velocity selective deposition experiments for fabricating high quality thin films. For the formation of Ag thin film by vacuum deposition method, YAG laser was irradiated to atoms or clusters parallel or perpendicular to the NaCl single crystal substrate, to deposit them on the substrate. For another experiment, Ag atoms selected in the given velocity were deposited on the (001) NaCl substrate by passing the molecular beam through the velocity selector. When laser was not irradiated, the thin film showed a random structure. Epitaxial growth was accelerated by the laser irradiation. When the selective velocity was set in 353 m/s at the constant intensity of molecular beam, the diffraction pattern of the thin film showed net pattern. When the selective velocity was set in 529 m/s, a structure in which ring pattern was overlapped on the net pattern was obtained. 2 figs.

  8. 3D electrical method and step continuous wave radar method for Nojima site. Results of measurement of resistivity at trench site; Nojima danso ni okeru sanjigenhi teikoho to step shiki renzokuha chika radar ho tansa. Trench chosa chiten deno hiteiko sokutei kekka

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, K; Oda, Y; Tank, K [Central Research Institute of Electric Power Industry, Tokyo (Japan); Hayashi, H [Kawasaki Geological Engineering Co. Ltd., Tokyo (Japan); Jomori, A [Japan Crust Research, Tokyo (Japan)

    1996-05-01

    Several surveys were carried out near the Nojima fault, including three-dimensional resistivity measurement and underground radar survey at the Ogura area, underground radar survey at the Hirabayashi area, and resistivity measurement in the vicinity of the trench at the Nashinomoto area, in order to investigate in detail the underground structures at a depth up to several tens meters from the ground surface. Resistivity was measured by an automatic analyzer capable of simultaneously measuring potential levels at 14 channels which can cover 112 measuring points at the largest. At the Ogura area, the boundary planes of the resistivity structures are continuously detected in the direction of the fault moving during the earthquake period. The underground radar measurement results suggest accumulated displacement of strata at a depth of around 25m in the Osaka Strata and flexible structures. At the Hirabayashi area, the underground radar analysis detects discrete sections in the reflection planes at the fault position, but no reflection planes of high continuity. At the Nashinomoto area, the clay stratum detected in the fault by excavating the trenches are found to be low in resistivity by the resistivity measurement. 4 refs., 11 figs., 2 tabs.

  9. Sensing of subsurface faults based on an imaging technique for teleseismic waveform data. 2. Feasibility study for application to oblique incidence, multi-event and noise data; Enchi jishin hakei data wo mochiita chika kozo imaging ni yoru chichu danso kenshutsu no kokoromi. 2. Naname nyusha, multi event, noise wo fukumu hakei eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Murakoshi, T; Takenaka, H; Saita, T [Kyushu University, Fukuoka (Japan). Faculty of Science; Suetsugu, D [Building Research Institute, Tokyo (Japan); Furumura, T [Hokkaido University of Education, Sapporo (Japan)

    1996-05-01

    An examination was made on the method in which imaging of subsurface was carried out with teleseismic waveform data for sensing of faults. In the examination, an experiment was done on the sensing of faults with higher precision, by applying oblique incidence as well as perpendicular upward incidence of SH plane waves, and thereby stacking the imaging in plural events. In numerical experiments, 28 observation points were arranged at 500m spaces apart on the surface, and the incident waves were made the SH plane waves having a bell-shaped time function, with incidence made at an angle varied as 0{degree}, +15{degree} and -15{degree} from the lowest layer of a model. In the calculation of the wave motion field, a difference calculus with secondary accuracy was used for both time and space. In addition, data was prepared with a random noise added to a synthesized waveform to be used as observation data. The calculated waveform data were likened to the observation waveform, to which the method for imaging faults was applied. Consequently, it was noted that satisfactory results were obtained compared with the case where faults were sensed by one event alone. 5 refs., 4 figs.

  10. Geotechnical engineering problems of construction works in the Shikoku district. 2. ; Construction work of Matsuyama expressway at fractured zones. Shikoku no kensetsu koji ni okeru doshitsu kogaku teki shomondai. 2. ; Shikoku jukan jidoshado (Doi@iyosaijo kan) ni okeru danso hasitai no norimen taisaku ko

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, T; Nagao, A [Japan Highway Public Corp., Tokyo (Japan)

    1991-09-25

    21.9km of the route between Doi and Iyosaijo of the Shikoku Jukan (Transverse) expressway was chosen along the central tectonic line which is the largest active fault in Japan. Countermeasure works for slope faces were carried out attaching importance to ground anchor and reinforced earth works, and the section was completed on March 29, 1991. In the section, longitudinal alignment, plain alignment and road structure were reexamined to determine the center line so as to avoid landslide areas as far as possible, and much cost curtailment was realized for the landslide countermeasure works although there were many slope face collapses during excavation. The collapsed soil amounted to about 50 to 600m{sup 3} for one collapsed spot, with 1 to 2m average thickness of the slid layers. Reinforced earth work method was found to be effective for small to medium scale slope face countermeasure works. PC anchor or other landslide countermeasure works were required for large scale landslides which have the depths of slide exceeding 2m. 5 refs., 7 figs.

  11. Report of commission for investigating MHD on a visit to U.S. Part 2. Report on each place of visit; Hobei MHD chosadan hokokusho. 2. Homonsakibetsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-01-01

    The members of MHD project examination subcommittee made an investigative tour of the U.S. on the state of development of MHD generation. This report of the 2nd part explains opinions and the present status of the R and D on MHD generation by each of the 19 institutions visited. The U.S. research on MHD generation is under the leadership of DOE, whereby the budget for the development is so large as nearly one hundred million dollars have been provided for several years. The purpose is the effective use of domestic coal. General Electric is of the opinion that a combined gas turbine system will be put to practical use earlier because MHD takes time for practicability despite its highest efficiency in coal-utilized power generation. Yet, GE thinks MHD will be more attractive in the future. Reynolds Metal is considering application of MHD generation to the electro-chemical industry at present. According to Reynolds, combined supply of electric output and heat of MHD can reduce the use of calorie per ton of aluminum from 240 MBTU to 100. Montana Power is promoting practicability through a combined plan with DOE-built MHD generation. (NEDO)

  12. Fiscal 1997 report on a feasibility study of international joint researches in the Asian region; 1997 nendo chosa hokokusho (Asia chiiki kokusai kyodo kenkyu kanosei chosa (4)hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is thought that the energy consumption in Asian countries with ASEAN and China as center will a marked growth also in future together with a rapid economic growth, but harmony with environmental problems and economic growth is being taken as a serious problem. This is an important issue also to Japan from viewpoints of secure energy supply and regional response to the environmental issue. Accordingly, strongly desired is positive response to global environmental issues and promotion in development/spread of new energy/energy conservation in these countries. For the spread of the technologies, actual construction/operation of plants by joint researches with Japan are effective from aspects of personnel raising, technical improvement, PR effects, etc. This is also helpful for Japan in terms of technological development because Japan can also get the unobtainable data from the operation under appropriate conditions. This is a report on the studies of the trends of global environmental problems in Thailand, Indonesia, Malaysia, the Philippines, India and China. 3 figs., 72 tabs.

  13. Fiscal 1997 report on the investigational research on intelligent social infrastructure technology; 1997 nendo chosa hokokusho (chiteki shakai kiban kogaku gijutsu no chosa kenkyu hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper first described an aim and outline of intelligent social infrastructure technology, summed up the system of social infrastructure and the situation in Japan in terms of the structure, lifeline, moving bodies such as railroad and automobiles, communication, security, and maintenance. Considering this present situation, the paper next described a concept of the intelligent social infrastructure technology to be newly constructed and a course of the development. Besides, as subjects required to study for the development of intelligent social infrastructure technology, it reported on risk management, methods of definition/collection/transfer/supply of information, infrastructure applicable at emergency, normal/emergency dual course system, privacy, robustness, and additionally the problems to be caused pertaining to architecture/civil engineering, traffic, security, communication, etc. when the infrastructure develops as a social system. Moreover, as element technology, the intelligent system related technology and data communication technology were described in detail. Examples of the research project were also reported. 101 refs., 70 figs., 42 tabs.

  14. Report for fiscal 1995 by basic liquefaction technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Delivered at the 1st meeting are a report on the fiscal 1995 research plan and an interim report, involving the use of coal-derived oils, research on refining technology using a PDU (process developing unit), reforming technology and petroleum blending technology for coal-derived oils, development of new reforming catalysts, technology of heterocompound separation, and the development of applications. Reported in relation with the development of environmentally friendly coal liquefaction technology are the study of coal liquefaction conditions, study of the upgrading of basic liquefaction techniques for the improvement and rationalization of the liquefaction process, and a project of liquefaction technology internationalization. A report is also given on a liquefaction catalyst study meeting. At the 2nd meeting, reports are delivered on the development of environmentally friendly coal liquefaction technology, including a briefing on the situation in general, designing of highly active catalysts, elucidation of the mechanism of emergence of activity, achievement of the marginal yield of coal-derived oils, and the properties of catalyst attached to coal. Delivered in relation with the use of coal-derived oils and technology for their refining are a briefing on the situation in general and reports on the blockup to occur in the naphtha fraction process and measures to counter the problem, control of the metamorphosis of active metals in reaction, heterocompound separation technology, and the development of applications. (NEDO)

  15. Investigational report on the trend of control technology; Seigyo gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    For the purpose of corresponding to changes of the industrial structure and making full use of the control technology, the paper investigated the state of the application. High-grade automation in the manufacturing industry has reached the spread of use at big companies for these 10 years. The hierarchical structure of business/process/DCS has been completed, and the optimal control and the advanced control have been realized. The development and spread to the much wider field is anticipated. The soft structure system is needed for equipment improvement in view of the life cycle of equipment and toward the elimination of bottlenecking. For the design of the control system, commercial tools began to be much used, and it is expected in future to accumulate and recycle the knowledge/knowhow for effective design work. Further, strict simulation models based material balance and heat balance have also been on the rise, and the advance in technology is expected. Because of the total productivity of the production equipment, the control technology is anticipated not only for the pursuit of controllability but for the use as supporting technology in the operation/driving/failure diagnosis for working out, carrying out and evaluating the optimum operation plan. 18 refs., 99 figs., 100 tabs.

  16. Report on new energy vision in Koushida Town area; Koushidacho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision was established in the Koushida Town area in Miyagi Prefecture. The population of Koushida Town has leveled off in recent years at 20,245 persons in fiscal 2000. However, number of people working outside the town is increasing, and the ratio of the daytime population is decreasing slowly. Agriculture in this town depends mainly on production rice of such brands as 'Hitomebore' and 'Sasanishiki', wherein the agricultural production amount is 3 billion 260 million yen in fiscal 1998. Commercial activities are decreasing its power with the annual retail sales amount of 17 billion 800 million yen, while the product shipping amount from the attracted factories is on the increasing trend, at 25 billion 700 million yen in 1998. The energy consumption is 526 times 10{sup 9} kcal in total, accounted for by the business department at 42.0%, the transportation department at 32.3%, and the consumer department at 25.7%. The annual utilizable quantity of new energies amounts to 28,816 times 10{sup 6} kcal, made available from solar power, wind power, bio-mass, and refuses, which is about 5.5% of the final energy consumption of the town. The new energy introducing project includes introduction of photovoltaic power generation into the town office building, facilities for interchange of citizens and schools, conversion of the automobiles used in the official organizations into clean energy fueled automobiles, the Eco-town Plan for the east side of Koushida Station, and the project of utilizing bio-mass supplied from the livestock market. (NEDO)

  17. Fiscal 1989 report on the bituminous coal liquefaction section meeting; 1989 nendo rekiseitan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    At the 1st, 2nd, and 3rd group meetings held for the fiscal year, reports are given and discussions are made about the progress of research and development. Reported and discussed in relation to the progress of the pilot plant support research are studies with the 1t/d PSU (process supporting unit) (Nippon Steel Corporation, Mitsui Coal Liquefaction Co., Ltd., and Japan Coal Oil Co., Ltd.); improvement on distillate distribution (Sumitomo Metal Industries, Ltd.); development of an optimum decalcification technique (Sumitomo Coal Mining Co., Ltd., and Sumitomo Metal Industries, Ltd.); studies of solvent hydrogenation catalysts (Sumitomo Metal Mining Co., Ltd., and Chiyoda Corp.); and studies of coal liquefaction conditions (Mitsui Engineering and Shipbuilding Co., Ltd.). In relation to studies using a bituminous coal liquefaction pilot plant, the progress of the 150t/d PP (pilot plant) effort (Japan Coal Oil, Co., Ltd.) and the outlines of pilot surveys (Japan Coal Oil Co., Ltd.) are reported and discussed, the latter covering liquefaction solvent performance optimization, slurry preheating furnaces, coal slurry properties, and so forth. (NEDO)

  18. Report for fiscal 1994 by Coal Gasification Committee; 1994 nendo sekitan gas ka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Summarized in this report is the material already distributed concerning the program for modifying the Nakoso 200t/d pilot plant entrained bed coal gasification furnace. The program aims to verify the overall suitability for power generation use of the air-blow pressurized 2-chamber 2-stage flow entrained bed gasification furnace. Although each specific feature of gasification furnace performance is found to be satisfactory, yet a 100% operation and extended continuous operation remain to be accomplished. Slagging is a phenomenon of ash grains in high-temperature gas adhering to and growing on the furnace walls to block up the furnace to eventually disable the furnace from continuous operation. In view of past achievements and test results, it is found that slagging is closely related to the behavior of floating or molten ash and to the transition temperature range. Various slagging measures have been taken for the current gasification furnace, but they prove to be ineffective. Some drastic measures need to be implemented for improvement. Under study using model furnaces and test furnaces are the reduction of slag generation at its source (re-entrained slag), prevention of adhesion (untrapped slag), removal of slag, optimization of gyration in the furnace, modification of slag properties for enhanced discharge, optimization of the transition gas temperature range, and the modification of furnace dimensions. (NEDO)

  19. Report on new energy vision in Koushida Town area; Koushidacho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision was established in the Koushida Town area in Miyagi Prefecture. The population of Koushida Town has leveled off in recent years at 20,245 persons in fiscal 2000. However, number of people working outside the town is increasing, and the ratio of the daytime population is decreasing slowly. Agriculture in this town depends mainly on production rice of such brands as 'Hitomebore' and 'Sasanishiki', wherein the agricultural production amount is 3 billion 260 million yen in fiscal 1998. Commercial activities are decreasing its power with the annual retail sales amount of 17 billion 800 million yen, while the product shipping amount from the attracted factories is on the increasing trend, at 25 billion 700 million yen in 1998. The energy consumption is 526 times 10{sup 9} kcal in total, accounted for by the business department at 42.0%, the transportation department at 32.3%, and the consumer department at 25.7%. The annual utilizable quantity of new energies amounts to 28,816 times 10{sup 6} kcal, made available from solar power, wind power, bio-mass, and refuses, which is about 5.5% of the final energy consumption of the town. The new energy introducing project includes introduction of photovoltaic power generation into the town office building, facilities for interchange of citizens and schools, conversion of the automobiles used in the official organizations into clean energy fueled automobiles, the Eco-town Plan for the east side of Koushida Station, and the project of utilizing bio-mass supplied from the livestock market. (NEDO)

  20. Research report on human media; Human media no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The human multimedia technology corresponding to users` subjective characteristics was researched to realize information environment producing a sense of unity with human. The human media technology realizes a human sensitive information processing model and a common database easily acceptable sensitively by various users. This technology also should be able to fairly accept and transmit individual`s information and knowledge as multimedia information, and in addition it is required to supply a virtual space with presence. In fiscal 1995, the research committee studied the concrete developmental issue for integrating these advanced fundamental technologies, and as practical images planned the prototype systems such as human media interactive plant operation, supply of environment supporting personal intelligent activities, and virtual medical center. The research committee also discussed development of space mobile media to secure energy-saving and safety of automobiles, and an environment simulation system with participation of many people. 34 figs., 2 tabs.

  1. Fiscal 1991 report. International Fuel Cell Conference; Nenryo denchi kokusai symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Lectures, presentations, and questions given at the event involved items 1) Plenary session, 2) Technology development strategies, 3) Phosphoric acid fuel cell (PAFC), 4) Molten carbonate fuel cell (MCFC), 5) Solid oxide fuel cell (SOFC), 6) Other fuel cells, and item 7) Closing session. Under item 1), current states and prospects of technological development were reported by Agency of Industrial Science and Technology of Japan and by industrial technology developing organizations of the U.S. and Europe. Under item 2), a report was given by the U.S. about a fuel cell-driven automobile developing program. Under item 3), a report was given on the exchange of information about plant operation, maintenance, and inspection with importance attached to accuracy. Under item 4), reports were given about a 70kW stack operating program of the U.S. and a 1MW stack pilot plant program of Japan. Under item 5), some NEDO (New Energy and Industrial Technology Development Organization) projects and a 25kW stack operating test of Westinghouse Electric Corporation were reported. What were learned through participation in this conference are mentioned below. Japan is in the forefront as far as the development of PAFC and MCFC technologies are concerned. The U.S. is ahead of Japan in the development of SOFC while also in Japan efforts to develop element technologies for SOFC are in progress steadily. The U.S. and European countries lead Japan in the development of the polymer electrolyte fuel cell (PEFC). (NEDO)

  2. Report on an analytical survey on the Pacific energy information; Taiheiyo energy joho bunseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of collecting and arranging energy information in the Asia and Pacific region, this survey has been conducted for many fiscal years. The Asia and Pacific region is classified into the Chinese area, the Southeast Asia area including Brunei, Indonesia, the Philippine, Singapore and Thailand, the East Asia area including Japan, Korea, Taiwan and Hong Kong, the North America area including the U.S. and Canada, and the Oceania area including Australia and New Zealand. As to the primary energy supplied from 1980 to 1993, China largely increased its share by 3.1%. The Southeast Asia also increased its share by 2.1%, and the East Asia by 2.5%. To the contrary, the North America area largely declined its share by 7.8%, but still has approximately 60% in the Asia and Pacific area. By kind of energy, coal increased the share while oil decreased. 16 figs., 7 tabs.

  3. Report on energy saving vision in Santo-cho region; Santocho chiiki sho energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    An energy-saving vision was decided on in Santo-cho region in Hyogo Prefecture, with its outline reported. This town is such that about 80% of the region is mountains, forests and wilderness and that aging is advancing at the rate above that of Hyogo Prefecture or the national average. Nearly entire energy of the town is dependent on the supply from outside. The energy consumption is somewhat increasing as a whole, with that of the people's livelihood/domestic sector and of transportation sector are rising. In the classification of fuels, electricity is growing in consumption. As an energy-saving vision, it aimed principally at personal surroundings in which every one got into the habit of saving energy continuously without being forced. The basic plan for the energy conservation drive consisted of inducement to an energy-saving life style, energy conservation to be spread by the next generation children, continuation of energy saving activity rooted in the region, and promotion of energy conservation as a basis for introducing new energy. The diffusion and enlightenment for children destined to lead the next generation were defined as a particularly important assignment, as was the promotion of energy conservation and environmental education. (NEDO)

  4. Survey and research on applications of parallel compiler; Heiretsu compiler tekiyorei ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-31

    An urgent proposition is made that an advanced computing software program development and maintenance system be set up, and activities are conducted in search of strategies and guidelines for the establishment of such a system. Out of recognition that it is important to develop software programs such as operation systems for supercomputers, a survey is conducted of software technology development strategies especially involving application software programs. It is proposed that efforts be positively exerted to develop strategic software developing programs for advanced computing for concentratedly enhancing the development now under way of strategic software programs. In concrete terms, named as strategic software programs to be developed are a next-generation semiconductor TCAD (technology computer-aided design) system, protein structure/function analysis system, fatigue simulation system, next-generation fluid analysis system, chemical reaction simulator, grid computing, and a nanodevice surface analysis system. (NEDO)

  5. FY 1994 report on the Coal Gasification Committee; 1994 nendo sekitan gasuka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper reported activities of the Coal Gasification Committee in FY 1994. The 1st Coal Gasification Committee Meeting was held on May 18,1994, the 2nd Meeting on October 28, 1994, and the 3rd Meeting on February 21, 1995. Report/discussion were made about activities of each section meeting and the progress of the development of coal gasification technology. For the 50 t/d HYCOL pilot plant, disassembly examination was conducted. As a result of the examination, the high-temperature gas corrosion caused by gas product against metal members was negligible, but against members in the wet corrosion environment, SCC, intergranular corrosion and pitting corrosion were generated. About members used in the high-temperature environment, it was made clear that Ir was applicable to thermowell, high chromia-base sintered products were applicable to non-cooling hearth tapping materials, and high chromia-base indeterminate-formed materials were applicable to water-cooled fireproofing wall. Based on the data obtained through the operational study of a 50 t/d pilot plant, conceptual design was made of a coal gasification hydrogen production plant of a scale of demonstration plant. (NEDO)

  6. Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

  7. Proceedings of RITE international workshop on valuation; Total eko balance ni kansuru kokusai workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The RITE International Workshop on Valuation was held in Tokyo and Osaka in February 1996, and eight papers on total ecobalance were reported. In The Field of Impact Assessment, described were constitution and methodology about impact assessment in a wide sense. In LCA Yesterday, Today and Tomorrow, discussed were the historical development and future outlook of LCA. In Standardization of Product Life Cycle Assessment, a survey of the present situation of LCA international standardization was made. In the Relationship between Product Life Cycle Assessment Methodology, considered was the relationship between the goal definition of the product life cycle assessment and the methodological choices. In Valuation in LCA, the present study of LCA was reviewed. Besides, reviews of the LCA study in Japan were made public.

  8. Investigational report on the trend of measures for global warming; Chikyu ondanka taisaku doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To know the trend of measures taken for global warming, conducted were overseas surveys, participation in academic society meetings, and literature surveys. The phaseout time of all ozone depleting substances responsible for the ozonospherial destruction was determined for both developed and developing countries in the 7th Meeting of countries which concluded the Montreal Protocol. As information on measures for protecting the ozonosphere, introduced was activities under United Nations Environment Programme (UNEP). New fluorine containing ethers were introduced as cleaning solvent which causes no ozonospherial destruction and is low in global warming index. Toxicity data were obtained on HFC-236ea and HFC-236fa which are promising substitutes in HCFC foaming and refrigerant fields. The paper introduced an outline of the 1st Meeting of countries which concluded the Framework Convention on Climate Change held in 1995. According to the report on the National Institute of Public Health and Environmental Protection of the Netherlands, the amount of emission of fluorine containing greenhouse effect gas (in CO2 conversion) reached 8-14% of all the amount of greenhouse effect gas emitted in 1990 unless the control is reinforced. An outline of the TEWI-3 project was introduced which is useful for comparing effects of substitution technologies on global warming. 14 refs., 11 figs., 29 tabs.

  9. FY 1993 report on the Material Committee; 1993 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper reported the FY 1993 activities of the Material Committee on the R and D of materials in coal liquefaction, coal gasification, coal utilization hydrogen production, etc. As to metal materials, a PSU implant test on 3Cr-1Mo base high-strength steel was conducted to examine mainly the hydrogen erosion resistance. Concerning surface coatings, aiming at improving the sulfuration corrosion resistance of Al{sub 2}O{sub 3} atmospheric plasma spraying materials, survey of the deterioration with age was made by inserting a test piece in which the structure of coated bed was altered into the PSU reaction tower. Relating to the R and D of trial manufacture of plant use equipment materials, study was made of the evaluation of characteristics of materials for improvement/trial manufacture of gasifier use refractory and the effect of improvement in erosion by coarsening treatment of mullite ceramics. As to the development of the control valve, etc., the control valve was manufactured using sintering diamond as sheet ring material and wolfram carbide as plug material, and the demonstrative test under the actual environment in PSU was carried out. The demonstrative test was also made on slurry flow meter and block valve. (NEDO)

  10. Fiscal 1991 report. Coal liquefaction committee; 1991 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The committee in this fiscal year had the 1st meeting in July 1991, the 2nd in August 1991, and the 3rd in March 1992, when fiscal 1990 research and development results, fiscal 1991 research and development programs, fiscal 1991 research and development results, etc., were reported and deliberated. At the 2nd meeting, the meaning of coal liquefaction technology development and how to go ahead with the task were described, which topic for discussion was entitled 'How coal liquefaction technology should be for the 21st century.' After discussion, it was agreed upon that a coal liquefaction technology package be completed in fiscal 2000 based on the absorption of each other's findings and on the utilization of basic studies common to both to be realized through the exchange of technologies between the brown coal liquefaction project and the bituminous coal liquefaction project. Under the brown coal liquefaction project, a 50 ton/day pilot plant was built and operated in Victoria, Australia, and the operation was completed in October 1990. The results of research and development under the coal brown liquefaction project will be compiled by fiscal 1993. (NEDO)

  11. Report for the coal type committee meetings in fiscal 1988; 1987 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The first committee meeting was held on September 30, 1987. The major agenda included: a development plan for the basic research, and as the summary of the achievements in fiscal 1986, Chinese coal liquefaction tests, coal type surveys, coal resource surveys, and as the research plan for fiscal 1987, coal resource surveys (Alaskan coal and Kalimantan coal), coal type surveys, and Chinese coal liquefaction tests. The results thereon were reported and deliberated. The second committee meeting was held on February 25, 1988. The agenda included: an interim report on the Chinese coal liquefaction tests, coal type surveys, coal resource surveys, (Alaskan coal and Kalimantan coal), as the interim report on the research achievements in fiscal 1987. Among the agenda, especially on the Chinese coal liquefaction tests, the data of the tests performed by the Chinese side and presented at the Japan-China joint technology sub-committee were introduced in detail, having drawn attention of the attendants. The first committee meeting reported the result of the autoclave test carried out by the Chinese side, the result of operation of the small continuous device (0.1 t/d) in fiscal 1986, and the result of the autoclave test performed by Mitsui Engineering and Shipbuilding for comparison. The second committee meeting reported the result of continuous operation implemented in China from August through September 1987 in the Chinese coal liquefaction test. (NEDO)

  12. Quiet STOL research aircraft development program. Teisoon STOL jikkenki kitai kaihatsu sogo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    The airframe development program of the quiet STOL research aircraft (ASKA) promoted by National Aerospace Laboratory, Japan is reported in detail. ASKA was developed based on a C-1 medium-sized troop and freight transport aircraft for the Air Self-Defence Force, and four turbofan- jet engines were substituted for two previous engines. Its first flight was conducted successfully on Oct. 28, 1985 after 8 year development from 1977 to 1985. The ASKA was developed separately on its airframe, engine and flight, and this report includes every related matter to its airframe. The promotion system, budget and executive system are reported in the second chapter, and the design requirements, safety standard and basic design in the third chapter. Several related tests such as wind tunnel test and flight simulation test are reported in the 4th chapter, and the structure and equipment of ASKA are outlined in the final chapter. The appendix includes the line-up of and discussions in the technical committee, the list of newly developed functional parts, the list of design reports and the list of related tests. 50 refs., 8 figs., 23 tabs.

  13. Report on the coal type committee meetings in fiscal 1988; 1989 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    This paper is a report on the coal type committee meetings in fiscal 1988. It summarizes the report mainly on the data distributed at the first and second coal type committee meetings. It describes liquefaction performance tests on Chinese coals in the coal type selection and investigation. In order to develop jointly by Japan and China the coal liquefaction technology, liquefaction tests have been performed on Chinese coals since fiscal 1982 by using the small continuous testing equipment (0.1 t/d) installed in the Beijing Soot and Coal Science Research Institute. The test is now in the third phase. The first sub-committee meeting reported the result on the Shenmu Simengou coal. The coal type investigation has analyzed coal samples collected from the world, classified them into brown coal, sub-bituminous coal of low coal rank, sub-bituminous coal, highly volatile bituminous coal of low coal rank, and highly volatile bituminous coal, and presented a list of candidate coals for liquefaction. Regarding the liquefaction performance tests on Chinese coals, the second coal type committee meeting reported the result on the Fuxin Qinghemen coal, and the result on the Tianzhu coal as revealed by using the NEDOL process BSU. The paper also presents the interim report on the research achievements in fiscal 1988 on the liquefaction performance tests on Chinese coals and the research achievements of the investigation and study in fiscal 1988 on the treatment technologies for coals used for coal gasification 'coal type selection and investigation'. (NEDO)

  14. Report on the material committee meetings in fiscal 1987; 1987 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The material committee has held two meetings in this fiscal year. The first committee meeting (September 25, 1987) was held for the major agenda of (1) the development of a centrifugal slurry pump for liquefaction plants, and as the research and development in fiscal 1987, the in-plant tests on new materials and the development a let-down valve, which were reported and deliberated. The major agenda of the second committee meeting (February 24, 1988) were, as the summarized achievements in fiscal 1987, (2) development of a technology to manufacture hydrogen by utilizing coal, (3) in-plant tests on new materials, and (4) development of a let-down valve, which were reported and deliberated. In Item (1), wear in the shaft seal of the centrifugal slurry pump was discussed regarding its cause from the result of a contraction flow test. In Item (2), it was verified that picrochloromite and chromia are integrated as an electromelting aggregate for the atmospheric stability of refractories used in a gasification furnace, and that the test conditions for the refractories call for the refractories to be tested under severe conditions. In Item (3), how to proceed the tests in the future was verified on such items as corrosion patterns, tested materials, coal types, and the degree of corrosion. In Item (4), kinds and temperatures were verified on slurries used in the water-slurry wear test and the fretting corrosion test. (NEDO)

  15. FY 1994 report on the Coal Liquefaction Committee; 1994 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper reported the FY 1994 activities of the Coal Liquefaction Committee. The Coal Liquefaction Committee in this fiscal year was held on November 29, 1994 (1st) and March 22, 1995 (2nd), and report was made on the bituminous coal liquefaction study and state of the R and D of liquefaction base technology. Report was also made on the state of construction of bituminous coal liquefaction PP, outline of the results of the PSU operation, outline of the 11th Japan-U.S. JTM, etc. In the liquefaction base study, report/discussion were made about the improvement/rationalization of liquefaction process, study of innovative technology of coal liquefaction, study of coal liquefaction conditions, study for higher liquefaction element technology, project on the internationalization of coal liquefaction technology, etc. As to the relation of the entrained bed coal gasification power plant, report/discussion were made about survey/study on the processing of coal for coal gasification use (survey of coal kind selection, development of information processing system for coal conversion technology). Besides, as a topic, report was made on the economical evaluation/calculation of a commercial plant for brown coal liquefaction. (NEDO)

  16. FY 1991 report on the Coal Gasification Committee; 1991 nendo sekitan gasuka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The paper reported activities of the Coal Gasification Committee, gasification power generation section and gasification technology section in FY 1991. The 1st Coal Gasification Committee Meeting was held on July 16,1991, and report/discussion were made about an outline of the FY 1991 research plan on the development of coal gasification technology. The 2nd Meeting was held on March 12, 1992, and report/discussion were made about activities of each section meeting and the progress of the development of coal gasification technology. In the section meeting of coal gasification power generation, report/discussion were made about the progress and study object of the development of entrained bed coal gasification power plant and support study for the development of the plant. In the 1st section meeting of coal gasification technology, as to the developmental plan on coal utilization hydrogen production technology, report/discussion were made about design/construction/operational study of pilot plant and support study for pilot plant (study using small equipment, study of trial manufacture of plant use equipment/materials). In the 2nd section meeting, report/discussion were made about the results of the development of coal utilization hydrogen production technology. (NEDO)

  17. Report on the coal liquefaction committee in fiscal 1992; 1992 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the coal liquefaction committee in fiscal 1992. The first committee meeting was held on August 21. After having confirmed the minutes of the previous meeting, an explanation was given on the research and development plans in fiscal 1992. The explanation covered the general explanation, bituminous coal liquefaction, brown coal liquefaction, and the common and fundamental aspects. The presented topics included the achievements in the operations using a bituminous coal liquefaction PSU and a small device, the status of compiling the achievements in the brown coal liquefaction project, preparation of the basic policy on developing the common basic technologies, and structuring of a coal liquefaction technology package. The second meeting was held on March 18, 1993. The meeting verified the minutes of the previous meeting, and gave the sub-committee reports for fiscal 1992. The sub-committees include those for bituminous coal liquefaction, brown coal liquefaction, environmental safety evaluation, and separation and refining technologies. As the summary of the achievements in fiscal 1992, descriptions were given on the bituminous coal liquefaction, brown coal liquefaction, and common and basic aspects. The fiscal 1993 plan presented included the budget aspect. A description was given as a topic on the economic performance evaluation and the working scheme (the execution plan) for the brown coal liquefaction process. (NEDO)

  18. FY 1989 report on the Coal Kind Committee; 1989 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The paper reported the FY 1989 activities of the Coal Kind Committee. The Coal Kind Committee in this fiscal year was held on July 24, 1989 (1st) and on February 21, 1990 (second), and report/discussion were made about the performance test on liquefaction of Chinese coal, survey of coal kind selection and international standards of coal. As to the performance test on liquefaction of Chinese coal, comparison was made between the results of the re-analysis/detailed analysis of the coal-derived liquids of Liaoning Province and Inner Mongolia in China which were tested at BSU in Beijing in this fiscal year and the results of the liquefaction test of the coal of Gansu Province in China which was made at BSU in Japan and BSU in China, and the discussion was actively made. Relating to the coal kind survey, report was detailedly made on the automatic analysis of maceral. The analysis of coal maceral requires time and skills, and to make it promptly and universally, the points to be cleared up, handling of two kinds of vitrinite, etc. were made clear. About the international standards of coal, the paper reported on the progress of the international conference held in Sidney in November 1988. (NEDO)

  19. Report on the coal type committee meetings in fiscal 1988; 1989 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    This paper is a report on the coal type committee meetings in fiscal 1988. It summarizes the report mainly on the data distributed at the first and second coal type committee meetings. It describes liquefaction performance tests on Chinese coals in the coal type selection and investigation. In order to develop jointly by Japan and China the coal liquefaction technology, liquefaction tests have been performed on Chinese coals since fiscal 1982 by using the small continuous testing equipment (0.1 t/d) installed in the Beijing Soot and Coal Science Research Institute. The test is now in the third phase. The first sub-committee meeting reported the result on the Shenmu Simengou coal. The coal type investigation has analyzed coal samples collected from the world, classified them into brown coal, sub-bituminous coal of low coal rank, sub-bituminous coal, highly volatile bituminous coal of low coal rank, and highly volatile bituminous coal, and presented a list of candidate coals for liquefaction. Regarding the liquefaction performance tests on Chinese coals, the second coal type committee meeting reported the result on the Fuxin Qinghemen coal, and the result on the Tianzhu coal as revealed by using the NEDOL process BSU. The paper also presents the interim report on the research achievements in fiscal 1988 on the liquefaction performance tests on Chinese coals and the research achievements of the investigation and study in fiscal 1988 on the treatment technologies for coals used for coal gasification 'coal type selection and investigation'. (NEDO)

  20. Proceedings of Japan-Germany Workshop of Bioremediation; Nichidoku bio remediation workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-04

    This is a proceedings of Japan-Germany Workshop on Bioremediation held on December 4 and 5, 1995. The keynote lectures include `Environmental preservation using biotechnology` by Prof. Karube of University of Tokyo, and `Environmental technology in Germany: status, achievements, and problems` by Prof. R.D.Schmid of University of Stuttgart. In the oral session, 7 papers are presented in the microbiological aspects of bioremediation, 10 papers in the environmental monitoring, and 6 papers in the engineering aspects of bioremediation. This workshop was sponsored by the German Federal Ministry for Education, Science and Technology, New Energy and Industrial Technology Development Organization, and Research Institute of Innovative Technology for the Earth. According to the lecture by Prof. Karube, key technologies for the environmental preservation include biotechnologies, such as the culture of fine algae with high CO2 concentration resistant properties using a solar light condenser, production of effective substances from CO2, and production of organic fertilizer from the sediments of lakes and sea. 19 refs., 12 figs., 3 tabs.

  1. Fiscal 1990 report on the bituminous coal liquefaction section meeting; 1990 nendo rekiseitan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    At the 1st, 2nd, and 3rd group meetings held for the fiscal year, reports are delivered and discussions are made concerning the progress of research and development activities. Reported and discussed in relation to the pilot plant support research, etc., are studies with the 1t/d PSU (process supporting unit) (Nippon Steel Corporation, Mitsui Coal Liquefaction Co., Ltd., and Japan Coal Oil Co., Ltd.); development of an optimum coal refining technique (Sumitomo Coal Mining Co., Ltd.); development of an optimum pretreatment technique and improvement on distillate distribution (Sumitomo Metal Industries, Ltd.); studies of coal liquefaction conditions (Mitsui Engineering and Shipbuilding Co., Ltd.); and studies of solvent hydrogenation catalysts (Sumitomo Metal Mining Co., Ltd., and Chiyoda Corp.). Reported and discussed in relation to researches using a bituminous coal liquefaction pilot plant are the progress of the 150t/d PP (pilot plant) effort (Japan Coal Oil Co., Ltd.) and the outlines of pilot surveys (Japan Coal Oil Co., Ltd.), the latter covering liquefaction solvent performance optimization, slurry pre-heating furnaces, coal slurry properties, and so forth. (NEDO)

  2. Fiscal 1995 report. Liquefaction key technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The subcommittee held the 1st meeting in September 1955 and the 2nd in March 1996, when fiscal 1995 research plans and research results were introduced and deliberated. In the study for designing a high-dispersion catalyst and the elucidation of the mechanism of activity expression, catalysts of highly dispersed iron supported on the brown coal surface in various ways were compared with each other in terms of liquefaction activity. Furthermore, geometric changes in the iron catalyst during the sulfurizing process were examined using the XRD (X-ray diffraction) and TEM (transient electromagnetic) methods. An improved catalyst was found to achieve a liquefaction yield near the Yallourn coal liquefaction limit in a high boiling solvent system. Concerning the study of coal oil product applications and refining technologies, reports were delivered on research results relating to the problem of blocking to occur during naphtha fraction refining and measures therefor, inhibition of active metal geometric changes during reaction, methods for separating hetero-compounds from coal oil and application thereof, and so forth. (NEDO)

  3. Report for fiscal 1995 by Coal Gasification Committee; 1995 nendo sekitan gas ka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This is a summary primarily of the distributed material. As of December 14, 1995, the 200t/d pilot plant for power generation by entrained bed coal gasification records a total coal gasification operation time of 4,485 hours with an accumulated amount of power generation of 9,227MWh. A large combustor is tested, and it is found that combustion is stable under a 1/4 load with low NOx emissions. The combustor is sufficiently cooled with a small supply of air. Coal ash and coal, supplied in a constant state for an improved heat recovery efficiency in the development of hydrogen-from-coal technology, are heated to a temperature near their melting points. They are then allowed to impinge at a heat transfer plane simulating a gasifier heat recovery section, and a study is made of the mechanism of ash adhesion, molten or semi-molten, to the heat recovery section. The reduction of the heat transfer coefficient due to added grains is 30-50%, and the reduction is small when the heat transfer pipe surface velocity is high or when the carbon concentration in the grains is high. In another effort, utilization of coal-derived gas as town gas is studied. As for yields as indicated by the Curie gas pyrolyzer, the gas yield increases and liquid yield decreases when the reaction temperature is high. Using a small test unit, it is found that a rise in the hydrogen partial pressure increases the production of both gas and liquid. (NEDO)

  4. FY 1990 report on the Material Committee; 1990 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    The paper reported the FY 1990 activities of the Material Committee on the R and D of materials in coal liquefaction, coal gasification, coal utilization hydrogen production, etc. As to the development/assessment of new materials for plant use, the sulfuration corrosion resistance was confirmed of aluminum diffusion coated agent and aluminized materials. Further, in the measurement of hydrogen permeability of the test piece exposed for 500 hours to the sulfuration corrosion environment, a good hydrogen permeation control effect was confirmed of hot-dipped materials and SiC/TiC plasma CVD materials. As to the development of the control valve, etc., CVD coating of Ti (C, N) and sintering diamond indicated good erosion resistance in the high speed water slurry injection test. Further, in the high speed powder injection test, PVD coating of TiN and sintering diamond indicated good erosion resistance. As to the development of the coal utilization hydrogen production technology, the following were carried out: improvement of gasifier use materials, assessment of materials under the corrosive environment where coal slag exists, experimental study on the repair technology, etc. (NEDO)

  5. Report for the coal type committee in fiscal 1992; 1992 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the coal type committee in fiscal 1992, and summarizes the main technological achievements. In the Chinese coal liquefaction test, fiscal 1991 has performed liquefaction tests on Fushun coal by using a small continuous testing facility (0.1 t/d) at the Coal Chemistry Research Institute in Beijing. Fiscal 1992 has completed the liquefaction tests on Shengli coal. In October, a liquefaction test was carried out by using Tianzhu coal according to the NEDOL process. This paper reports the result of the liquefaction test on the Shengli coal, and the result of the analysis on the Fushun coal liquefied oil. The coal type selection and investigation having been performed to date reveals close correlation among the maceral composition of coal, coal rank and liquefied oil yield. Coals having good reactivity and suitable for liquefaction are generally suitable also for gasification. In the pretreatment of coal as a gasification material for hydrogen manufacture, a test was performed by using A heavy oil and tar sand bitumen plus A heavy oil as the granulating agents. With Montana coal, the highest de-ashing rate was achieved when the oil was added at 35% by weight. Both of the reaction rate and oil yield were improved. A handling test was carried out up to 72.5 degrees C, wherein Tatung coal presented no problems in both of the discharging and sticking tendencies. (NEDO)

  6. FY 1992 report on the Coal Kind Committee; 1992 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper reported the FY 1992 activities of the Coal Kind Committee. The Coal Kind Committee in this fiscal year was held on September 28, 1992 (1st) and on March 4, 1993 (second), and report/discussion were made about the performance test in Chinese coal liquefaction, survey of coal kind selection, development of handling technology, etc. As to the performance test in Chinese coal liquefaction, there were the data very different in quality among the data, and it was pointed out that it was necessary to make a close re-examination of sites for sample collection and sampling methods. Relating to the survey of coal kind selection, the following were pointed out: The inertinite value in the maceral analysis was not necessarily in agreement with the reactivity; The inertinite was dependent largely on temperature for the reaction; It was necessary to make parameters based on the chemical structure. As to the development of the coal utilization hydrogen production technology, the paper reported the experimental survey of coal pretreatment, development of new deheterocyclicity and deashing technologies, experimental survey of coal handling, etc. (NEDO)

  7. Fiscal 1993 report. Coal liquefaction committee; 1993 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The committee in this fiscal year had the 1st meeting in July 1993, the 2nd in December 1993, and the 3rd in March 1994, when fiscal 1993 research and development programs and results were reported and discussed. Reported and discussed at the 2nd meeting were the compilation of brown coal liquefaction technology development project results, evaluation report on the same, hydrorefining of oil from brown coal and the research and development of application technologies for the same, and an environmental safety evaluation test on the same. In selecting a standard coal for the operation of the 150 ton/day pilot plant, PSU (process supporting unit)-aided studies were made on the analytical values presented by coals, yield of the liquid, yield of the liquefaction residue, yield of the generated gas, amount of the hydrogen consumed, coal oil properties, liquefaction residue properties, operationality, etc. On-site investigations were conducted also in Indonesia, and a conclusion was reached that Tanito Harum coal would be the most suitable for the pilot plant. Concerning the liquefaction catalyst for the pilot plant, a report was given on a comparison made between the activity of a synthetic iron sulfide and that of natural pyrite. (NEDO)

  8. Fiscal 1994 report. Liquefaction key technology subcommittee; 1994 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The subcommittee held the 1st meeting in August 1994 and the 2nd in March 1995, when preceding fiscal year's research results, fiscal 1994 research plans, fiscal 1994 research results, etc., were introduced, and deliberated. In the study of hydrorefining of naphtha, kerosene, and light oil fractions, a nitrogen concentration level of not more than 5 ppm was achieved by refining oils from Indonesian coal. Studies were also made about the two-step hydrorefining system, the relationship between the coal oil refining level and sludge formation, etc. In the research for the development of novel catalysts for upgrading coal oil, the active life of a nickel-supporting catalyst for hydrogenation at the 1st step was somewhat prolonged with an increase in the amount of nickel. In the study of coal liquefaction conditions, an AWIP method was deliberated, wherein liquefaction process waste water was utilized as one of catalytic component adjusting materials. For upgrading liquefaction key technologies, studies were made for catalyst improvement and pretreatment method development, and about the behavior of liquefaction reaction in a high boiling solvent-aided process. (NEDO)

  9. Report on the analytical survey of the Pacific energy information; Taiheiyo energy joho bunseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Arrangement, investigation and analysis of an energy information exchange system were conducted, with the aim of coping with the development in the whole Asia/Pacific area, the stabilization of energy supply/demand, and the environmental problem and of realizing effective cooperation of every country in the area. Concerning the trend of the domestic primary energy supply/demand, there are some patterns. Countries which show high growth rates are developing countries such as Thailand and China, and NIES such as Korea and Taiwan. Countries where growth rates are slowing down and lowering are developed countries such as Australia, Canada, Japan and the U.S. Countries where energy supply/demand is not stabilized are Singapore, Hong Kong, Indonesia and Chile which are suffering from variations in import/export. The ultimate energy consumption is the domestic primary energy supply from which the conversion loss in the conversion sector was deducted, and indicates almost the same trend as the primary energy supply. It is divided into a stabilized type of developed countries and a rapidly increasing type and a stagnant type. However, there are some exceptions. Total data in the quarter of the year cannot be the yearly data by itself, but requires a year-end tax arrangement. 40 tabs.

  10. Report on regional new energy vision for Kahoku town; Kahokucho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A regional new energy vision has been formulated for Kahoku town, Kochi Prefecture, which features the introduction of recoverable energy harmonious with nature and friendly to human life and environments. The results of activities conducted in this connection are compiled into nine chapters, which cover (1) Kahoku-town's local characteristics relative to new energy, (2) survey of townspeople's awareness of new energy, (3) amounts of new energy in existence, (4) basic policy toward introduction, (5) study of concrete measures for promoting introduction, (6) study of prioritized projects, (7) establishment of target amounts for introduction, (8) coordination with energy conservation measures, and (9) a system for thrusting forward the regional new energy vision toward embodiment. Chapter (7) comprises the way of setting target values for introduction; study of the target values to be achieved by the industry, administration, and citizenry, respectively; and a conclusion on the target values. Studies are conducted in the chapter about the introduction of solar energy, wind power generation, small scale hydroelectric power generation, cogeneration, clean energy vehicles, and the like. It is predicted that 960 kl/year will be introduced in fiscal 2010 in terms of oil, which accounts for 12% of energy consumption. (NEDO)

  11. Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

  12. Research report for establishment of NEDO vision; NEDO vision no sakutei ni muketa chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Because of an increase in energy demand due to economic growth and industrial structure change in the Asian area and its effect on global environment, the economic evolution harmonizing with energy and environment (3E) of the Asian area is required. The role of Japan, in particular, NEDO for achieving such 3E was studied from an international viewpoint. The following are thus surveyed: The history of energy demands, economic growth, an increase in energy consumption and their effect on global environment in the Asian area, and the policies, measures and future plans of Asian countries corresponding to the above situations. The role of NEDO is first of all R & D of biomass toward practical use, and development of effective use technology of biomass energy. Positive approach to control of CO2 emission and immobilization of CO2 is also required in industrial and traffic fields. As technology transfer from Japan, promotion of joint researches and establishment of an economic support scheme are expected together with transfer of the basement technology and training. 79 figs., 13 tabs.

  13. FY 1992 report on the Coal Liquefaction Committee; 1992 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper reported activities of the Coal Liquefaction Committee in FY 1992. In the 1st committee meeting, report/discussion were made of the summary of the FY 1992 R and D plan on the bituminous coal liquefaction, brown coal liquefaction and the common/basic technology. Further, the following were reported as topics: results of the operation by bituminous coal liquefaction PSU and small equipment, state of arrangement of the results of the brown coal liquefaction project, making of the basic policy for development of the common/basic technology, construction of package of coal liquefaction technology. In the 2nd committee meeting, the summary of the results of the FY 1992 R and D was reported/discussed. As to the development of bituminous coal liquefaction technology, study using pilot plant and support study were reported. Concerning the development of brown coal liquefaction technology, study using a 50t/d pilot plant and complementary study of operation. Relating to the development of the common/basic technology, trial manufacture/development of plant equipment/materials, survey of selection of coal kind, etc. The paper also reported a scheme on the evaluation of efficiency of the brown coal liquefaction process. (NEDO)

  14. Report on new energy vision in Fudai Village area; Fudaimura chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision was established in the Fudai Village area in Iwate Prefecture. The population of Fudai Village is decreasing from the peak of 4,103 persons in 1985. Its basic industry is fishery and agricultural industries, with the fish and marine product raising industry particularly active. The energy consumption in Fudai Village is, in the decreasing order, the transportation field (48.5%), the social and household field (26.5%), social industry, and manufacturing industry. Homes consume room heating energy at a greater extent. Energies are supplied by fuel oil at 53,554 Gcal (79.3%) and electric power at 11,551 Gcal (17.1%). The new energy introducing project has discussed introduction of cogeneration into the Kurosaki House, introduction of photovoltaic power generation and solar heat utilization systems, and introduction wind power generation as a tourism symbol. Discussions were also given on conversion of the automobiles used in the official organizations into clean energy automobiles. Further discussions were given on introduction of small new energy facilities, such as hybrid illumination, small wind power generation, and photovoltaic power generation, into the village office, the station square, the fish market, facilities in the fishing port, the children's hall, and the Road Station. (NEDO)

  15. FY 1981 report on the Coal Kind Survey Committee; 1981 nendo tanshu chosa iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    For the purpose of establishing coal liquefaction/gasification technology, investigational survey on the usable coal resource in Japan was made to collect/file the data on the state of coal existence, coal kind, etc. by the Coal Kind Survey Committee and the section. In the 1st committee meeting, an idea of the coal kind survey was discussed, and in the 2nd committee meeting, a summary of activities in this fiscal year was reported. In the section meeting, the following were carried out: discussion of a course of the coal kind survey in the 1st meeting; discussion about how to proceed with the coal kind survey/items of data filing in the 2nd meeting; examinational study of items of data filing in the 3rd meeting; summary of activities in this fiscal year in the 4th meeting. As examples of the coal kind survey, the following were cited: special study report on coal resource and gasification/liquefaction characteristics by Science and Technology Agency; results of the survey by Joint Coal Board and Queensland Coal Board in Australia; Report of 1978 by The Fuel Society of Japan; Report of 1976 by Pennsylvania State University; data on process raw coal by The Iron and Steel Institute of Japan, etc. (NEDO)

  16. Coal liquefaction committee report for fiscal 1981; 1981 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    For the assurance of smooth progress of coal technology development endeavors, the New Energy and Industrial Technology Development Organization (NEDO) has installed coal technology development committees (general committee on coal technologies, coal liquefaction committee, plant materials committee, coal type survey committee, total system committee, and coal gasification committee). The coal liquefaction committee deliberates and evaluates liquefaction technology and propels forward smoothly the efforts to develop the technology. Under the coal liquefaction committee, there are four subcommittees, which are the 1st subcommittee (primary liquefaction subcommittee), 2nd subcommittee (solid/liquid separation subcommittee), 3rd subcommittee (secondary hydrogenation subcommittee), and the 4th subcommittee (brown coal liquefaction subcommittee). The 2nd and 3rd subcommittees deal with common tasks as they were studied in fiscal 1980. The 1st subcommittee incorporates into itself the old subcommittees that respectively worked on the three liquefaction processes (the direct hydrogenation process, the solvent extraction process, and the Solvolysis process), and is designed to provide a site for information exchange. A brown coal liquefaction committee is incorporated into the coal liquefaction committee as the 4th subcommittee. This report is a compilation of the agendas of the respective subcommittees of the coal liquefaction committee. (NEDO)

  17. Fiscal 1991 report on the brown coal liquefaction section meeting; 1991 nendo kattan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    At the 1st through 5th brown coal liquefaction group meetings held for the fiscal year, reports are delivered and discussions are made about the progress of research and development. At the 1st meeting, a fiscal 1991 brown coal liquefaction research plan is introduced, and discussed. At the 2nd meeting, an interim report on the brown coal liquefaction technology development project is discussed. At the 3rd meeting (a joint meeting of the brown coal and bituminous coal liquefaction groups), an agendum entitled 'what the development of brown/bituminous coal liquefaction technologies for the 21st century should be' is reported, and discussed. At the 4th meeting, reports are made on the results of deliberation at the Industrial Technology Council, progress of the follow-up study, progress of the collection of achievements, and so forth. At the 5th meeting, the outline of the follow-up study, the collection of achievements in the pilot plant study (a project report preparation schedule and materials evaluation), the progress of pilot plant dismantling work, etc., are reported and discussed. (NEDO)

  18. Report on studies on closed cycle MHD power generation; Closed cycle MHD hatsuden kento hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Summarized herein are results of the studies on closed cycle MHD (CCMHD) power generation by the study committee. The studied system is based on the MHD gas turbine combined Brayton cycle of about 500,000 kW in output power, firing natural gas as the fuel, and the conceptual design works therefor are completed. The major findings are: the overall plant efficiency: 54.2% at the power transmission side, plot area required per unit power output: 0.04 m{sup 2}/KW, unit construction cost: 251,000 yen/KW, and unit power generation cost: 10.2 yen/KWh. This system will be more operable than the gas turbine combined cycle with steam system, because start-up time, output change rate, optimum load and so on are constrained not on the power generator side but on the gas turbine side. The expected environmental effects include the exhaust gas NOX concentration being equivalent with that associated with the conventional power generator of 2-stage combustion system, quantity of combustion gases to be treated being approximately 40% of that associated with the gas turbine combined cycle, and reduced CO2 gas emissions, resulting from enhanced power generation efficiency. It is expected that the CCMHD system can exhibit higher efficiency than the high-temperature gas turbine combined cycle system. (NEDO)

  19. Fiscal 1989 report. Coal liquefaction committee; 1989 nendo sekitan ekika iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The committee in this fiscal year had its 1st meeting in June 1989 and 2nd meeting in March 1990, when fiscal 1989 research and development programs and fiscal 1989 research and development results, etc., were reported and discussed. The operating status of the 1 ton/day PSU (process supporting unit) for bituminous coal liquefaction was reported and discussed. The report included its 1st operation for the demonstration of a long-term stable run under standard conditions that continued for trouble-free 50 days, the 2nd operation for the investigation of the effect of liquefaction reaction temperature in which the liquefaction yield recorded the maximum at 450 degrees C with the collection of coal oils of 55 wt.% on the average, and the 3rd operation for the investigation of the effects of liquefaction reaction pressure and catalyst injection size whose details were being analyzed. Reported in relation with the brown coal liquefaction pilot plant was a comprehensive operation of a series of 1st hydrogenation, solvent deashing, and 2nd hydrogenation processes completed after a continuous operation of 460 hours establishing a total operating time of 1050 hours. (NEDO)

  20. Coal rank survey committee report for fiscal 1981; 1981 nendo tanshu chosa iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    A coal type research project is started under which data concerning the coal resources that Japan can make use of are to be gathered, which are necessary for determining their fitness-for-use in a coal liquefaction or gasification process, and the gathered data are to be compiled into files which are easy to use. As for the buildup of a computer-aided data bank, since the number of coal types is not yet large, only part of the data is taken into consideration this fiscal year. In the study of compiling the data into files, it is decided that the files be divided into two categories, one for grasping the status of the development project as a whole and the other for defining the positions of the individual coal specimens. Provided in the former are outlines covering the name of coal mine or project, location, entrepreneur, states of the mining area and geology, state of production, infrastructure-related matters, etc. Described in the latter are the details that enable the identification of given specimens such as the coal bed or coal brand, location and method of collection, collector, date, amount of the specimen, method of treatment, etc. (NEDO)

  1. Report for the coal type committee meetings in fiscal 1993; 1993 nendo tanshu iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This paper reports a joint meeting of the coal liquefaction committee and the coal type committee in fiscal 1993. The report is focussed on the coal type selection (the final report) for the coal used in the 150-t/d coal liquefaction pilot plant (PP) among other agenda. Initially the Australian Wandoan coal was scheduled to be selected as the reference coal for the PP operation, but the mine has not gone into operation, hence the schedule was given up. Screening was carried out to select a coal which is commercially produced and exported, and contains ash at 10% by weight or less, sulfur at 1.5% by weight or less, and chlorine at 300 ppm or less. An autoclave and a 0.01-t/d flowing type device were used to evaluate liquefaction performance, whereas the Tanito Harum coal produced in Indonesia, very similar to the Wandoan coal, was selected as a promising candidate. A PSU was used to demonstrate overall operation performance. The coal is an appropriate reference coal as seen from the aspects of liquefied oil yield, nature, operability, and site surveys in Indonesia. Among the actual record of four kinds of PSU coals in the past, the present coal has the oil yield ranked high, has the least liquefaction residues, and is advantageous economically. The oil yield per ton of coal has cleared the PP target of four barrels. The coal has less ash, is easy in solid/liquid separation in the depressurized distillation, and has no problems in operability, excepting the matter of coal supply. (NEDO)

  2. Report on Seminar on Clean Coal Technology '93; Clean coal technology kokusai seminar hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-11-01

    The program of the above clean coal technology (CCT) event is composed of 1) Coal energy be friendly toward the earth, 2) Research on CCT in America (study of coal structure under electron microscope), and 3) Research on CCT in Australia (high intensity combustion of ultrafine coal particles in a clean way). Remarks under item 1) are mentioned below. As for SO{sub 2} emissions base unit, Japan's is 1 at its coal-fired thermal power station while that of America is 7.8. As for the level of SO{sub 2}/NOx reduction attributable to coal utilization technologies, it rises in the order of flue gas desulfurizer-aided pulverized coal combustion, normal pressure fluidized bed combustion, pressurized fluidized bed combustion, integrated coal gasification combined cycle power generation, and integrated coal gasification combined cycle power generation/fuel cell. As for the level of CO2 reduction attributable to power generation efficiency improvement, provided that Japan's average power generation efficiency is 39% and if China's efficiency which is now 28% is improved to be similar to that of Japan, there will be a 40% reduction in CO2 emissions. Under item 2) which involves America's CCT program, reference is made to efforts at eliminating unnecessary part from the catalytic process and at reducing surplus air, to the export of CCT technology, and so forth. Under item 3), it is stated that coal cleaning may govern reaction efficiency in a process of burning coal particles for gasification. (NEDO)

  3. FY 1991 report on the bituminous coal liquefaction section; 1991 nendo rekiseitan ekikabukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The paper reported activities of the bituminous coal liquefaction section in FY 1991. In the 1st bituminous coal liquefaction section meeting, report/discussion were made on the outline of the plan on the FY 1991 research using pilot plant and the support study of pilot plant. In the 2nd section meeting, report was made on 'How the development of coal liquefaction technology should be in the 21st century,' a report made by the joint section of bituminous coal/brown coal liquefaction. In the 3rd section meeting, report/discussion were made on the state of progress of the FY 1991 R and D and results. In the study using the bituminous coal liquefaction pilot plant, report was made on the outline of construction of a 150t/d pilot plant, study on the acquisition of material balance, analytical study of the data on liquefaction tower, testing survey on properties of coal slurry, and testing survey on slurry preheating furnace. In the support study of pilot plant, report was made on the study using 1t/d PUS, study on the development of the optimum coal refining technology and improvement in the distillate distribution, study of conditions for coal liquefaction and study of solvent hydrogenation catalyst. (NEDO)

  4. Assessment report on the development of functionally inclined material; Keisha kinosei zairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Concerning a project whose aim is to develop heat resistant engine members through the application of the concept of functionally inclined materials, deliberation and assessment are made of the meaning of its implementation, validity of the research program, research achievement, etc. The project deals with a specimen, diameter 150mm or more and thickness 5mm or more, built of a zirconia/stainless steel-based functionally inclined material, and its goal is to develop technologies for optimizing the baking process for the said specimen, baking system and related devices, assessment technique, tribological assessment technique, etc., and it is inferred that these targets are reasonable. As the result of this research, an energy-efficient (power consumption reduced to 1/3 to 1/5) practical rapid sintering system is constructed. Basic data are collected relative to the tribology of the functionally inclined material, and it is proved that it is feasible to use the material for engine members. The process technology, assessment technology, and devices developed under this project are the first in the world, and are highly evaluated. (NEDO)

  5. Report on the material committee in fiscal 1988; 1989 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    This paper describes a report on the material committee for coal gasification technology development in fiscal 1988. The in-plant test on new materials has performed information investigation on use characteristics and use records of new materials. A sulfurizing corrosion resistance test showed that the aluminum-chromium diffused and permeated material and the molten aluminum plated material stabilize the coated surface and have high corrosion resistance. Ceramics painted lining material was evaluated unusable in a steam diffusion test. Phenol resin was found sufficiently usable as a result of giving the stress test at 100 to 150 degrees C. In developing a let-down valve, a high-velocity water slurry injection test revealed that CVD coating of Ti (C, N) has high effect of suppressing the erosion damage. In a high-velocity powder injection test, PVD coating of TiN and CVD coating of TiC were found to show good erosion resistance. Tests and researches were performed to evaluate durability of furnace materials for manufacturing gasified hydrogen, and elucidate conditions to cause iron oxide burst. Evaluation on repairing techniques, and improvement on durability were also executed. (NEDO)

  6. Report for fiscal 1993 by coal gasification committee; 1993 nendo sekitan gas ka iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This report is a compilation mainly of distributed material. In the development of entrained bed coal gasification power generation, gasification is tested in a 2t/d-capable facility and gasification efficiency and operation characteristics are grasped, these constituting the studies of elements to assist pilot plant operation etc. The fluid temperature point of slag is found to decrease by 200 degrees C at the maximum upon addition of flux (CaO), and this improves on slag fluidity. For the development of a demonstration gas turbine, an experimentally built combustor is tested using a real gas. A combined cycle power system is studied by simulation. In the study of pilot plant operation, measures relative to slagging are implemented, inspection and maintenance are conducted for each facility, and the combustor for a demonstration plant is subjected to oil and coal combustion tests. In the study of a pilot plant for developing technologies for hydrogen production using coal, the plant stably runs more than 1,000 hours under 100% load at in a RUN-8-3 operation. Some deposit collects in the neighborhood of the contracted area of the blow nozzle and on some part in the slip stream, but it does not affect operation. No abnormalities are detected in the cyclone or heat recovery boiler. The pilot plant is let to continue its operation, and excellent results are achieved, which are beyond the targets of carbon conversion efficiency of 98% or higher and gas cooling efficiency of 78% or higher. (NEDO)

  7. Fiscal 1991 report on the brown coal liquefaction section meeting; 1991 nendo kattan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    At the 1st through 5th brown coal liquefaction group meetings held for the fiscal year, reports are delivered and discussions are made about the progress of research and development. At the 1st meeting, a fiscal 1991 brown coal liquefaction research plan is introduced, and discussed. At the 2nd meeting, an interim report on the brown coal liquefaction technology development project is discussed. At the 3rd meeting (a joint meeting of the brown coal and bituminous coal liquefaction groups), an agendum entitled 'what the development of brown/bituminous coal liquefaction technologies for the 21st century should be' is reported, and discussed. At the 4th meeting, reports are made on the results of deliberation at the Industrial Technology Council, progress of the follow-up study, progress of the collection of achievements, and so forth. At the 5th meeting, the outline of the follow-up study, the collection of achievements in the pilot plant study (a project report preparation schedule and materials evaluation), the progress of pilot plant dismantling work, etc., are reported and discussed. (NEDO)

  8. Compact digital NTSC TV signal transmission system using SM optical fibers and its application to operating status monitoring for laser cutting machine; Digital gazo shingo no kan`igata hikari fiber denso system to sono laser cutter no dosa jotai kanshi eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Asada, H. [NEC Shizuoka, Ltd., Shizuoka (Japan); Rabou, N. [University of Helwan, (Egypt); Ikeda, H.; Shimodaira, Y.; Yoshida, H. [Shizuoka University, Shizuoka (Japan)

    1998-02-01

    This paper describes a compact bandwidth-compressed digital NTSC picture code transmission system in which circuit configurations are simplified and made inexpensive. The bandwidth of digital NTSC picture codes is compressed in accordance with subjective evaluation, and so the sampling rate is set at 8.13 MHz (2.28 times fsc) and the quantizing level at 5 bits. The frame bits for detecting the frames of picture elements me generated by alternately generating 1 and 0 when the frames are specified. The proposed system is constructed using edge- emitting LED`s (ELED`s) and single- mode (SM) fibers for transmitting digital NTSC picture codes w m to easily distribute video signals from a video camera to video monitors. The transmitter was 80 times 100mm in size, 120 g in weight, and 1000mw in power dissipation. The receiver was 55 times 120 mm in size, 100g in weight, and 800mw in power dissipation. Using the compact bandwidth-compressed digital NTSC picture code transmission system a shot of the working pice in the laser cutting machine, as an example, was satisfactorily transmitted via SM optical fibers without noses. 18 refs., 12 figs., 2 tabs.

  9. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  10. Leading research and study report for fiscal 1998. Report on leading research and study on intelligent fiber; 1998 nendo sendo chosa kenkyu hokokusho. Inteligent fiber sendo chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches were conducted with a view to organizing projects for developing intelligent fibers, equipped with environmental friendliness and amenity without being deprived of their original properties as structural and clothing materials, the ultimate goal of the effort being the creation of harbingers of next-generation fibers which would contribute to the advance of industries related to environments, medicine and welfare, and information. What were learned from fiscal 1998 researches are mentioned below. The strength that the general-purpose fibers currently in use exhibit is so small as to be but several percent of what is theoretically predicted for them. Demand will increase a great deal if the actual strength is doubled, for which new technologies have to be developed including those involving super-fiber texture control. For providing the fiber with such functions as environment-friendliness, amenity, etc., it is necessary to develop phasal structure control technologies with regard to fiber morphology, surface texture, etc. For success in practical application in the future of such super-fiber materials, each specimen needs to be manufactured in the order of kilogram by way of trial. Moreover, fiber evaluation techniques have to be developed in the three domains of software, hardware, and interface. (NEDO)

  11. Fiscal 1997 survey report. Basic survey on trends of waste use type production facilities and waste fuel production facilities; 1997 nendo chosa hokokusho. Haikibutsu riyogata seizo shisetsu oyobi haikibutsu nenryo seizo shisetsu doko kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This survey was made to obtain the basic data for future spread and promotion of No.6 type (waste use type production facilities) and No.7 type (waste fuel production facilities) which were added to the objects having been subsidized since fiscal 1997 under `the environmental harmony type energy community project.` In the former, the kiln in the cement industry and the blast furnace in the steel industry can be extremely large places to receive waste plastic since the facilities are distributed in every area and the treatment capacity is large. However, the effective collection, transportation and sorting of large quantity of waste plastic, especially the problem of removal of vinyl chloride, is a big bottleneck. As to the use of waste plastic using gasification technology, there are no actual results on the commercial basis. That is, however, appropriate for treatment of the waste difficult in treatment, and can be expected of the usage in the chemical industry. In the latter, in the facilities using industrial waste raw materials as fuel, solidification and liquefaction are both operated on a commercial basis. In relation to the solidification and use as fuel of general waste, the treatment of combustion ash is preventing the expansion of use of waste in the industrial field because of a large quantity of chlorine included in the products. 92 refs., 54 figs., 35 tabs.

  12. Fiscal 1998 research report. Research on the possibility of promoting CDM project through technology transfer with plant exports; 1998 nendo chosa hokokusho. Plant yushutsugata gijutsu iten wo tsujita CDM project suishin kanosei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on promotion of CDM (clean development mechanism) project through technology transfer with plant exports. Although CDM system was provided in COP3 on climate change held in Kyoto in 1997, its detailed rules including project approval are yet undecided, and only the schedule to provide the detailed rules until COP6 in 2000 was decided in COP4 in 1998. The common recognition that the CDM project with plant exports produces various merits for both Japan and the partner country is increasing. However, from the viewpoint of forming concrete CDM projects, most Japanese enterprises are passive in approach to the CDM project because of no detailed design of CDM, uncertain profitability and procedures, and avoidance of additional burdens. Plant export is also difficult because of the fact that assessment of a new project is difficult. Enterprises' deeper recognition on the CDM project, and a governmental integrated support system are desirable. (NEDO)

  13. Research report of fiscal 1997. Study on total energy and material control (feasibility study on circulating society); 1997 nendo chosa hokokusho. Total energy and material control ni kansuru chosa (junkangata shakai kochiku kanosei chosa) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to construct real sustainable global environment and human society in the 21st century called the century of environment, not only the innovation of manufacturing processes technically supporting such the construction but also the conception including the innovation of the whole society from a wide viewpoint are essential. As a total energy and material control system (TEMCOS) concept, the view of an energy-saving circulating society is attempted which minimizes a total energy and material flow in Japan, and the role and issue of manufacturing industry, in particular, material industry are extracted. As one of the targets of such a concept, the conception of an eco-town is also described. Paying attention on some important material industries including a mass material flow and consuming a large amount of energy such as metal, plastics and automobile industries, the study result on a material flow for every industry is arranged, and some effective issues contributing to minimize a material flow and control energy consumption and CO2 emission are extracted. 80 refs., 67 figs., 30 tabs.

  14. Report for fiscal 1980 on comprehensive survey for nationwide geothermal resources. Survey on Curie point method (Associated material - operation flight report); 1980 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Curie tenho chosa (futai shiryo sagyo shinchoku hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-10-01

    With an objective to identify the status of distribution of deep underground thermal structure, aerial magnetism investigations were executed in the south Kyushu area, and data used in the Curie point method were collected. This paper summarizes the progresses and achievements of the work during the investigation. The report for April 1981 summarized preparation of equipment and materials by EG and G Geometrics Corporation, and the work schedules with the Idemitsu Geothermal Development, Petroleum Resources Development, and Naka-Nippon Airways. The report for April 22 compiled the site preparation and the test flight. The report for April 28 compiled the calibration and magnetism compensation flight. The report for May 5 compiled the implementation of the second flight , and the result of survey for 292 km in total. The report for May 10 compiled the implementation of the third to fifth flights, and the results of measurements for 584 km, 519 km and 360 km, respectively. The report for May 18 compiled the implementation of the sixth to eighth (final) flights, and the results of measurements for 513 km, 584 km and 68 km, respectively. (NEDO)

  15. FY 1992 report on the survey of geothermal development promotion. Electromagnetic exploration (TDEM method) (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Denji tansa (TDEM ho) hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    For the purpose of elucidating a possibility of existence of geothermal reservoirs in the Haneyama area, Oita Prefecture, Electromagnetic survey by the TDEM method was conducted. The survey was made for the area of 80km{sup 2} at 105 measuring points in the south of the Haneyama area, and the resistivity structure reaching the depth of 4,000m from the earth surface was made clear. The resistivity structure in this area is composed of 4 layers: upper medium resistivity layer, central medium resistivity layer, central low resistivity layer and lower high resistivity layer. The resistivity structure discontinuous line ranges between the uplift zone of basement and the sedimentation zone, and the greater part of the alteration zone is distributed and arranged concomitant with the position and direction of the line. As the region with high potential of geothermal existence, cited were the low resistivity zone distributed in the west of the resistivity structure discontinuous line that continues from Mt. Fukuman to the south, the low resistivity zone distributed in the north of the resistivity structure discontinuous line from Noya to the west, and the low resistivity zone distributed in the north of Hosenji and lying between resistivity structure discontinuous lines. (NEDO)

  16. Report of the results of the fiscal 1997 survey. R and D of high efficiency clean energy vehicles; 1997 nendo chosa hokokusho. Kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing an automobile which keeps low pollution using petroleum substituting clean energy, decreases the running energy consumption to a half at least, and reduces the CO2 emission to less than a half of the conventional one at the same time, the R and D started in fiscal 1997. As to the study of a high efficiency hybrid power system, conducted were the prediction of fuel consumption performance of the system proposed, evaluation of element technology using hybrid simulator, evaluation experiment on a new hybrid vehicle, and grasp of overseas trends. In relation to the development of hybrid vehicles, the following were studied: methanol fuel cell loading hybrid vehicle, CNG engine loading hybrid vehicle, CNG ceramic engine loading hybrid truck, CNG lean burn engine loading hybrid truck, LNG engine loading hybrid bus, and DME engine loading hybrid bus. Besides, a survey on synthetic fuel and the related survey were carried out. 17 refs., 185 figs., 101 tabs.

  17. Leading research report for fiscal 1998 on the report on researches on intelligent social infrastructure technology; 1998 nendo chiteki shakai kiban kogaku gijutsu no chosa kenkyu hokokusho sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches are conducted for showing some guidelines on the system and method of the intelligent social infrastructure technology (ISIT) as a 21st century type systematization technology, and a report is submitted on the result. Discussed in the report are the technological system and image of ISIT, the research and development setup and administrative tasks involving intelligent social infrastructure construction, and the systematization and operation of the ISIT. Mentioned as important element technologies are the infrastructure and information/communications technologies for security and disaster prevention, information technology and automatization technology for maintenance, and intelligent materials enabling disaster prediction and detection. Stated in connection with the future development of ISIT are information/communication technologies for system control, monitoring, and normal/urgent dual use. Specific examples are shown, such as the active card, urban disaster prevention and monitoring system, active city, intelligent network, and so forth. (NEDO)

  18. FY 1997 report of survey on the intellectual property in international collaboration research project; 1997 nendo chosa hokokusho (kokusai kyodo kenkyu ni okeru chiteki zaisanken ni tsuite no chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In promoting international collaboration research project, coordination of the patent system of each country which participants to the project belong to has broad implications in concluding the contract for the project. For example, in Japan, 100% of the patent belongs to the government for contrast or collaboration project with the government. While, in the USA, the patent developed by the private company belongs to the private company even for the contrast project. In Japan, the shared patent can not be transferred to the third party or implemented without agreement with the partner. While, in the USA, the shared patent can be transferred to the third party or implemented without agreement with the partner. Due to such a difference, some projects can not be established by ill coordination of intellectual property even when the meaning of the projects is well understood. In this survey, was investigated the outline of patent systems of major countries to study about what should well balanced treatment of intellectual property in international collaboration research project be in the future. 4 figs., 8 tabs.

  19. Fiscal 1997 survey report on the trend of global warming protection measures of substituting freons; 1997 nendo chosa hokokusho (daitai freon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The trend survey was conducted of global warming protection measures by participation in international conferences, scientific society meetings and lecture meetings, and by literature surveys. We participated in the international conference on ozonosphere protection measures. In the 9th meeting of the nations which concluded the Montreal Protocol, the strengthening of restrictions on methyl bromide was decided on. In the UNEP solvent technology selection conference and the OORG conference of the World Bank, reports were made on substituting solvents in Japan, activities supporting developing countries, and the developmental trend of urethane use foaming agent. In the international conference on ozonosphere protection measures, introduced were the present status of Japan`s ODA for developing countries and examples of success of the substitution in the solvent field. The paper included nine reports on CFC destruction technology related literature made public in the past one year. The paper also introduced a comparative study of de-HCFC substituting technology at U.S. Oak Ridge National Laboratory, U.S. EPA`s prediction of emission of fluorine 3 gas, the predicted value of HFC emission and trial calculation of contributing rate in all greenhouse gases by IIR, Green Peace and Elf Atochem, and NOAA`s measured data on SF6 in the atmosphere. 49 refs., 46 figs., 26 tabs.

  20. FY 1992 report on the survey of geothermal development promotion. Geochemical survey (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Chikagaku chosa hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    For the purpose of studying an expanse and characteristics of the geothermal system and a possibility of geothermal development in the Haneyama area, Oita Prefecture, geochemical survey was conducted. In the survey, various kinds of analyses were made for 13 specimens of hot spring water and 5 specimens of surface water in the area of about 280km{sup 2} at 402 measuring points of the concentration of Hg in soil gas. The results of the survey were as follows: In this survey area, it was thought that the HCO{sub 3} type geothermal water of a comparatively low temperature which was heated by the wide-spread conduction heat from the depths was widely distributed deeper than the depth of 500-700m, and it was presumed that a possibility was low of existence of a high geothermal potential which can be used for the geothermal power generation in the part deeper than the drilling depth of 700m. In the Noya area in the southwest part of the survey area, the high temperature deep geothermal reservoir was confirmed. In this area, the high temperature neutral-alkalescent Cl-SO{sub 4} type geothermal water was distributed in the depth of several 100 meters or deeper. The geothermal water seemed to flow from NE to SW along the structure in the NE-SW direction, and it was concluded that the area was the most promising one. (NEDO)

  1. Fiscal 1998 research report on information structuring technology for advanced use of NEDO research reports; 1998 nendo NEDO seika hokokusho nado no kodo riyo ni hitsuyona joho kozoka gijutsu no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was made on electronic NEDO research reports corresponding to the recent extending trend of Internet. The logical structure and electronic format of NEDO research reports as document were first studied considering document disclosure and reuse of technical information. HTML as electronic format for Internet is unfortunately insufficient to describe the logical structure of NEDO research reports because of HTML's restricted description. Thus, XML which is being watched because of its possible definition of original tags was studied in place of HTML. As a result, because at present preparation of standards on XML and a compatibility for implementation of standards are insufficient, it was concluded that construction of the electronic document system for NEDO research reports is still too early. However, since adoption of XML as document format is important from the viewpoint of a property succession on Internet, preparation of the XML format file of NEDO research reports is essential. (NEDO)

  2. Fiscal 2000 achievement report on the research and development of transfer standard gage for oil flowmeter (final assessment); 2000 nendo sekiyu ryuryokei no iten hyojunki no kenkyu kaihatsu seika hokokusho (saishu hyoka hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In a servo PD (positive displacement) flowmeter for oil, a differential pressure transmitter detects difference in pressure between the PD flowmeter input and output ports and a rotor is driven by a servo motor so that the pressure difference between before and after the PD flowmeter rotor will be zero. The design enables high-accuracy measurement across a wide range of flow rates and is not easily affected by the surrounding physical conditions such as viscosity and density. For the development of such a flowmeter, it is necessary to develop a rotor that rotates smoothly free of locking in a steady and uniform flow, to build a visualized model that enables the analysis of flow inside the flowmeter which in turn will enable the determination of optimum differential pressure detecting ports, and to connect a newly developed servo mechanism to the thus determined ports. As the result of the research, a servo PD flowmeter is developed, which is a 50mm diameter prototype employing the Invoflex tooth form which is the waveform for a rotor suitable for a high performance flowmeter. Placed in a generally used oil flow calibration liquid, which is gasoline, kerosene, or the like, it covers a flow rate range of 1:10 and reads with an accuracy of {+-}0.1%. It remains stable in performance and suffers but a little change with the passage of time. (NEDO)

  3. FY 2000 report on the survey of technological strategy for the creation of the robot society in the 21st century; 2000 nendo chosa hokokusho. 21 seiki ni okeru robot shakai sozo no tameno gijutsu senryaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    For the purpose of constructing the future-oriented robot technology system and clarifying the robot technology strategy viewed from the necessity, contribution and marketability in the society, investigational study was made by the special committee for technology strategy survey. In the section meeting for the needs, the following 5 working groups had a grasp of the needs: reinforcement of production technology; bio-industry; medical act support; how to cope with disasters; life support. Based on the results of the analysis of factors of the successful manufacture of industrial robots during the 1980s - 1990s, the quantitative estimate of the market was made as much as possible. Further, in the section meeting for the seeds, the 6 working groups were set up, and they conducted the trend survey/analysis of the development of element technology of robot in Japan and abroad, the extraction of developmental subjects, etc. As a result, the following were specified as the seeds to be emphasized: construction of the remotely distributed system using network; nano-handling technology; sensitivity interface/human behavior comprehension technology/simulation technology, robot vision, moving technology, advanced manipulation technology. (NEDO)

  4. FY 1992 report on the survey of geothermal development promotion. Gravity prospecting (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Juryoku tansa hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    For the contribution to elucidation of the geothermal structure in the Haneyama area in Oita Prefecture, gravity prospecting was conducted. Survey was carried out in the area of about 280km{sup 2} at 205 measuring points, and analysis was made altogether with the existing 3,273 gravity measuring points. As a result, the following were made clear. The gravity basement forms the fault-state structure that sinks several 100 meters to the south side on the line from the south edge of the Higashi-shiiya ridge to Mt. Kurotake - Mt. Daigansen - Amagase hot spring in the SW direction. This fault was made correspondent to the Beppu north fault on the east side of Mt. Kurodake. Each of the following regions is the region where the fault-state structure that predicts the development of fracture and the area of distribution of alteration zone that can be cap rock overlap each other: NW edge of Shishimuta sedimentation zone - Machida alteration zone distribution area; N edge of the Shishimuta sedimentation zone - Ibushi alteration zone/Noya alteration zone distribution area; Vicinity of Mt. Kurodake - Hijiu alteration zone distribution area. It seems that the above-mentioned regions have high potentiality of geothermal exploration. The region where new igneous activities are seen, which is near the heat source, is important for exploration. The distribution area is seen near the west of the Mizuwake Pass ridge. (NEDO)

  5. FY 1994 report on the survey of geothermal development promotion. Complementary survey on the fracture system, etc. (Wasabizawa area); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho futai shiryo. Wasabizawa chiiki danretsu kei tou hokan chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    For the contribution to elucidation of the geothermal structure in the Wasabizawa area, Akita Prefecture, survey by the paleomagnetic measurement and fracture system measurement was conducted of the borehole cores and specimens of outcrop granite obtained from boreholes of N6-WZ-3 and N6-WZ-4. In the survey, the following were carried out: measurement of the core fracture system of N6-WZ-3 (102-1,505m) and N6-WZ-4 (507-1,556m), paleomagnetic measurement of 9 outcrop granite specimens and 16 core specimens, and k/Ar age determination of 3 outcrop granite specimens. As a result of the paleomagnetic measurement of outcrop granite, the magnetization azimuth of the schistose granodiorite distributed in Kuwanosawa was regarded as almost NS. The measured magnetization azimuth of the core specimen obtained from the same rock mass was also made NS-based, and measurement of the fracture in the neighborhood was made. As a result, it was found out that the NNW system was dominant in dikes and that there was the NE system in most of the small geothermal channels. The fracture system of well tended to develop around the boundary between granite and metamorphic rock, and it was thought that this part could be a reservoir if temperature conditions are prepared. (NEDO)

  6. FY 1974 report. Study on hydrogen combustion technology; 1974 nendo suiso nensho gijutsu ni kansuru kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    In the use of hydrogen as fuel, there is the problem on NOx emission. The amount of NOx emission is not as much as in the use of coal or oil, but is more than in the use of natural gas or town gas. However, it can be said that hydrogen is an ideal fuel if considered that it does not emit other air pollutants such as CO, HC and soot/dust which are usually associated with hydrocarbon base gas fuels, and also that hydrogen forms a circulation system which is ecologically sound. The flame of hydrogen is non-luminous, but the flame temperature is high. The formation of NOx depends strongly upon the flame temperature, and therefore, in the design of hydrogen burner, it is necessary to well mix it with air and to avoid the production of the local high temperature region. Further, when using hydrogen to large boiler, the combustion technology to control NOx reduction is needed. About the hydrogen flame, the matter to be noticed is an experimental result that NOx reduction was observed by adding trace ammonia to hydrogen gas. If this method can be successful, NOx can be reduced with no increase in fuel consumption. It leads to hydrogen's reaching a position of clean energy. (NEDO)

  7. Fiscal 1998 report on Japan-Asia international cooperation project; 1998 nendo Nichi Asia kokusai kyodo kenkyu jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the development of talent, industrial infrastructures, and new industries in countries that received Japanese cooperation, Japanese researchers were sent to universities and research organizations in Asian countries, where they were engaged in joint research and development, which involved (1) micro device technology, (2) technology for manufacturing industrial silica material by chaff incineration, (3) technology for forming and machining of alloys difficult to machine, light in weight, and high in strength, (4) technology for rare metal isolation and refining, (5) cascade-wise utilization and practical application of biomass in Asia, (6) exploration and utilization of microbial resources in Tropical Asia, (7) evaluation of biological resources existing in Southeast Asia and construction of information network, (8) development and evaluation of cultured articular cartilage, (9) technology for utilizing wastewater for production of valuable substances, and (10) studies for utilizing biological resources through utilization of diversity of symbiotic microbes and their adaptability to surroundings. Under item (1), it was planned that ultrasonic micro transducers and micro fluid devices be developed for use in the medical field. (NEDO)

  8. Report on establishment of new energy vision in Akeno Village (Yamanashi Prefecture); Akenomura shin energy vision sakutei hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established to move positively forward the introduction of reproducible new energies and promotion of energy conservation at the district level, based on the basic conception of 'protecting and nurturing nature and culture of Akeno Village to leave them to the future generations'. The activity achievements were put into order by the following five items: 1) basic conception and basic policy in establishing the new energy vision, 2) the general situation of Akeno Village, 3) investigation on energy demand and supply in Akeno Village, 4) estimation of existence quantity of new energies, and 5) the new energy introduction vision. Item 5 is composed of the conception in establishing the idea, new energy introduction plans, and new energy introduction projects. The new energy introduction projects include introduction of photovoltaic power generation into Akeno Middle School, installation of wind power generation facilities at open space in the 'Road Station', introduction of hybrid street lights using micro wind mills and solar cells into the school zone roads, and introduction of clean energy fueled automobiles into official use automobiles. (NEDO)

  9. Report for fiscal 2000 on feasibility study for commercializing new energies; 2000 nendo shin energy jigyoka feasibility study hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    Tobu Town in Nagano Prefecture has established a 'Tobu Town new energy vision' and set up a polity to make efforts in discussing new energy introduction into public facilities which will be constructed in the future. Discussions were given on commercialization possibilities of the energy center system, particularly energy supply by cogeneration utilizing natural gas, for the four facilities in the 'Forest of Welfare'. Comparison was performed on primary energy consumption, CO2 emission reducing quantity, and economic performance between the existing energy supply systems and the energy center system. Discussions were also given on means to utilize solar energy. The plan calls for establishing the energy center in the 'Forest of Welfare', wherein facilities composed mainly of a gas engine type cogeneration plant (500 kW) and a solar heat collector (36.4 m{sup 2}) will be installed to supply the object facilities with electric power and hot water. This operation will be able to reduce the primary energy consumption by 12% and CO2 emission by 18%. (NEDO)

  10. Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-10-01

    Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

  11. Report on bio-energy survey project in Sumoto City; 2001 nendo Sumoto baio energy chosa jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    With an intention to solve environmental problems and energy problems simultaneously in Sumoto City, Hyogo prefecture, surveys have been performed on feasibility of introducing biomass energy in the district. The dairy farming in Sumoto City has a trend of increase in the number of livestocks being fed in individual farms, and increase of milking quantity per livestock (increase of sewage discharge amount), with the increase of excessive excreta amount causing a problem. The Sumoto Dairy Farming Association is experiencing generation of excreta of 156 tons a day, which requires manure handling and disposal of 112 tons a day even after deducting the field dispersion. Discussions on a biogas plant with a capacity of 100 tons a day call for biogas generation amount of 2,500 m{sup 3} a day, electric power generation amount of 4,500 kWh a day, fuel cell size of 100 kW x 2 units, and heat generation amount of 6,000 kWh a day. A total of the estimated project cost amounts to 2,450,000,000 yen, the annual running cost to 65,280,000 yen, and the annual income to 82,000,000 yen. The electric power generation cost is 135 yen per kWh, the heat production cost is 952 yen per liter (converted to kerosene), and the saving amount due to excessive electric power and heat utilization amounted to 10,700,000 yen. The annual amount of CO2 reduction is 1330 tons. (NEDO)

  12. Achievement report for fiscal 1998. Home rehabilitation system for aphasia patients; 1998 nendo seika hokokusho. Shitsugosho zaitaku rehabilitation shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Development has been made on the element technologies for a home rehabilitation system for aphasia patients. First, studies were performed on an authoring procedure for aphasia patient training, and partial trial production and development were carried out on an authoring system for the training program formula. Then, studies were executed on a training simulation and analysis filter, and partial trial production and development were implemented on a home rehabilitation supporting and self-teaching system. Next, an input and output mechanism for voice signal processing was studied, and aphasia patient and caregiver human interface was partially fabricated on a trial basis. In addition, a remote rehabilitation communicating method was researched, and partial trial production was carried out on a remote rehabilitation evaluation and diagnosis support means. Finally, communication assisting means were researched, and a communication assisting system was partially produced on a trial basis. Good evaluation results were given on a demonstration system. Although partial indications were given on minute parts, practical agreement was obtained as a whole. Great expectation was given particularly on the remote rehabilitation system and the authoring system. (NEDO)

  13. Report on investigation in fiscal 2000 of industrial technology information; 2000 nendo sangyo gijutsu joho chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Pursuing the measures for how the national research institutions in Japan who have been made into independent administrative corporations should be positioned in maintaining and developing the industrial strength, investigations were performed with the points focused on measures taken in the United States to improve research environment, and the ways the national research institutions should be. The investigation results were summarized on the following four areas: 1) transition of research and development policies, 2) on the national research organizations, 3) structuring of database for researchers in universities and national research organizations, and 4) future challenges and suggestions. Item 1) has put the subject into order of the history of establishing legislations related to the U.S. technological policies, measures to promote research and development, budgetary management, grants, and preferential treatment. In Item 2), visits and investigations were executed on government-owned, government-operated laboratories and government-owned, contractor-operated laboratories whose operation patterns are different with each other. The results were put into order of institutions, roles, personnel systems, activation measures, joint research institutions, and finance. In Item 3), a data list was prepared on researchers relative to advanced technology programs contributing greatly to enhancing the competitive edge of U.S. corporations. (NEDO)

  14. Summary of achievement reports on the Sunshine Project in fiscal 1978 (Hydrogen energy); 1978 nendo seika hokokusho gaiyoshu. Suiso energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-04-01

    This paper summarizes achievement reports on the Sunshine Project in fiscal 1978 (hydrogen energy). In hydrogen manufacturing methods, studies are described on materials of membranes and electrodes used in high temperature and pressure electrolysis. In thermo-chemical method, studies are continuing on cycles of the iron system, iodine system, and mixed system (composed by thermal, photo and electro-chemistries). For the iodine system, summary design was performed on an experimental device. For the mixed system, trial fabrication and experiments were carried out on a beam radiation type electrolytic tank that electrolyses quickly HI and Fe{sup 3+} produced in the photo-chemical reaction, and separates the products. Discussions were also given on HI decomposition (hydrogen acquisition) by means of heat diffusion. With respect to storage and transportation, development is being made on optimal metal hydrides. In combustion technologies, discussions are given on combustors and catalysts to break through the dilemma of high NOx emission and frequent occurrence of reverse ignition. For fuel cells, the paper describes developments of the materials thereof, high-temperature solid electrolyte type fuel cells and alkaline aqueous solution electrolyte type fuel cells. Regarding the non-steady hydrogen engines, the paper describes fundamental studies on non-steady jet flow behavior using shock tubes, and single cylinder engine tests. It also describes hydrogen safety assuring measures, and studies on energy systems. (NEDO)

  15. New energy visions for City of Sapporo. Report on the survey results; Sapporoshi shin energy vision chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    This project is aimed at survey/study on new energy reserves and possibility of their introduction for City of Sapporo, and, at the same time, drawing the future visions for introduction of new energies to reshape the city. The new energies considered are solar energy and waste heat carried by sewage, in addition to waste heat from garbage incineration and garbage-derived solid fuels, which are now already utilized as the heat sources for district heat supply. The city as a whole consumed energy of 28,100Tcal/y in 1985 and 45,700Tcal/y in 1996, and emitted carbon dioxide totaling 2,690,000 and 3,510,000 tC/y in the respective year. The projects considered for introduction of new energies include construction of a new cleaning plant and heat supply system at the southern gate of Sapporo Station, introduction of clean energy automobiles, increasing attractiveness of Satoland project, utilization of low-temperature heat at glass pyramids in Moere Park, promotion of photovoltaic power generation, construction of facilities for culture-exchanging, and construction of an environmental plaza. (NEDO)

  16. Report on new energy vision establishment in Oga City area; Ogashi chiiki shin energy vision sakutei hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established in Oga City in Akita Prefecture. The population of the city is continuing the decreasing trend since 1955 to 30,462 persons as of 2000. The number of employed people by industry is in the trend of decreasing in the primary industry, leveling off in the second industry, and increasing in the tertiary industry. The annual energy demand in this city is 838,000 MWh in electric power and 302 times 10{sup 13} J, accounted for by the consumer department at about 44.4%, the transportation department at about 28.3% and the industrial department at 27.3%. The carbon dioxide emission amount therefrom is estimated 68,100 t-C. The expected usable quantity of new energies in the city would be available in solar heat as the largest source, followed by solar beam and wind power, whose amount is estimated 136.41 times 10{sup 13}J annually in total. The new energy introducing project includes introduction of wind power generation into Namahage Line and its vicinity and the Ikari area, manufacture of fuel from refuses, introduction of clean energy fueled automobiles into the cars used by the city office, introduction of photovoltaic into the general gymnasium and primary and middle schools, and solar heat utilization at the general gymnasium. (NEDO)

  17. Research report of fiscal 1997. Feasibility research on domestic wind farms; 1997 nendo chosa hokokusho. Kokunai wind farm kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research was made on large-scale wind power generation projects under planning or construction. Issues of the following 5 areas were arranged considering topographic, geographic and meteorological conditions, and the type of municipal corporations: Tomamae town, Hokkaido, Tachikawa town, Yamagata prefecture (third-sector), Hisai city, Mie prefecture, Otoyo town, Kochi prefecture, and Kishuku town, Nagasaki prefecture (third-sector). These projects are supported by MITI`s local new energy introduction promotion project subsidy started in fiscal 1997 covering a half of construction cost (within 200 million yen/year). Requirements for this subsidy are that an applicant is either a municipal corporation or a third-sector, and that a total generating capacity is not less than 1200kW. Another subsidy system covering 1/3 of construction cost and a debt guarantee system are prepared for large-scale private projects not less than 800kW. Hearing was made on some private projects in Esashi town, Akita city and Hasaki town. Technical requirements, specifications, guideline and some examples for system interconnection are also summarized. 10 figs., 24 tabs.

  18. Report on the environmental safety evaluation sub-committee in fiscal 1992; 1992 nendo kankyo anzensei hyoka bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the environmental safety evaluation sub-committee for the coal liquefaction plant in fiscal 1992. The sub-committee, upon having received reports on the result of environmental safety evaluation tests performed in fiscals 1991 and 1992 by NEDO, deliberated and discussed carefully the contents thereof. In order to ensure labor hygiene for coal liquefaction plant workers, health influence on liquefied oil users, and social acceptability of the liquefied oil, NEDO has performed the comprehensive brown coal pilot plant operation and oil safety tests. The tests are in accordance with the labor safety and hygiene law, the chemicals examination law, and the MPD issued by OECD, and performed on each fraction produced in the pilot plant and the whole fraction mixing the former fractions, using rats, rabbits, and guinea pigs. The test items included: acute inhalation toxicity and oral repeated administration (using rats); eye stimulation, repeated coating and skin stimulation (using rabbits); photo-toxicity (using guinea pigs); mutagenicity tests (microorganisms, bacteria and chromosome anomaly); resolution tests; fish toxicity; concentration degrees; algae growth obstruction; and water flea breeding obstruction. As the result, the toxicity was found light. (NEDO)

  19. Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1980 reported. This year, a detailed conceptual design was carried out on a coal fired MHD generation system, with points for the technological development concretely examined. In addition, investigation was conducted on the progress of MHD generation technology, development situation of other generation systems, state of energy resources, etc., in various foreign countries. In the conceptual design of the coal fired MHD generation plant, the system structure of a 2,000 MWt class commercial MHD generation plant was explained, as were the conceptual design of the structural elements and proposals for a 500 MWt class demonstration plant and an 100 MWt class experimental plant, for example. In the overseas trend of R and D on MHD generation, investigations were made concerning the U.S., Soviet Union, and China, with details compiled for such items as generation plants, combustors, generation channels, heat resisting materials, superconducting magnets, heat exchangers, seed slags, inverters, boilers and environments, and commercial plants. (NEDO)

  20. Report on a survey in fiscal 1999. Survey on research exchange possibility; 1999 nendo kenkyu koryu kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey deals with research institutions of governmental organizations, universities, and business entities for the purpose of discussing the possibility of research exchange standing on a long-term point of view to serve for solving global environment problems, and the way the exchange should be. The research exchange shall cover the areas of trends in research and development of global environment related technologies, themes for the research and development, institutions for the research and development, and exchange of researchers and information with these research organizations. In fiscal 1999, three survey missions were dispatched to cover the following three areas: (1) surveys on research possibility of catalyst development by means of combinatorial chemistry, (2) surveys on research exchange possibility for thermo-chemical solar hybrid fuel production technologies, and (3) surveys on research exchange possibility for structuring function improving technologies of the 21st century type. Each survey mission has visited research institutions of the world to survey the trends in researches related to global environment, and the possibility of exchanging researches with RITE. The visits presented the following conclusions and findings: (1) the research on the combinatorial chemistry in the U.S.A. is still in the initial stage; (2) important findings were obtained when surveys were made on methane reformation utilizing solar heat, and coal gasification technologies in Europe; and (3) surveys were made on pioneering researches on plant molecule physiology in Europe. (NEDO)

  1. Fiscal 2000 achievement report. Welfare technosystem research and development (Ube); 2000 nendo walfare technosystem kenkyu kaihatsu (Ube) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts continue to develop welfare nursing equipment for helping persons in need of nursing care or handicapped persons who live an independent life. Efforts are exerted in three fields for developing (1) a motor driven wheelchair in which the occupant feels as if driving a car, (2) an online cardiac function monitoring system using a cardiac sound sensor, (3) an automatic pressure belt for patients of postural low blood pressure, (4) and a seated position aiding and stabilizing device for workers with legs not fully useful. In field (1), the steering wheel, brake, and driving system are contrived so that the occupant may easily drive the wheelchair as if in an automobile driver's seat. In field (2), a device is developed to monitor and examine the heart rate and respiration rate, for which a cardiac sensor has to be installed on the water bed or an air mattress. In field (3), a computer controlled automatic pressure belt is developed for patients of myelopathy or cerebrovascular disease. In field (4), a work assisting device is developed to help seated workers with leg troubles. (NEDO)

  2. Report on the brown coal liquefaction sub-committee in fiscal 1992; 1992 nendo kattan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the brown coal liquefaction sub-committee in fiscal 1992. The first sub-committee meeting presented an interim report on the status of progress in complementary researches in fiscal 1992. The report covers the following items: discussions on effects of reaction factors on scale deposition in a preheater and a reactor and the liquefaction oil yield, supplementary experiments to enhance recovery rate of naphtha from under-flow in the de-ashing system and enhance accuracy of expression to estimate the interface precipitation velocity, and discussions on product oil types and catalyst types. The second sub-committee meeting reported fundamental discussions on the primary hydrogenation and hot water treatment of brown coal as an interim report on the achievements, and discussions on de-ashing and catalyst properties, liquefying reaction activity and scaling performance of catalysts. The third meeting reported the support on compiling the achievements by means of collecting complementary data of the pilot plant using PDU. A 7,800-hour life verification test was completed on the fixed bed secondary hydrogenation catalyst. A method was established to recover naphtha from the under-flow in a de-ashing settler. An expression to estimate the interface precipitation velocity was also established. Affirmation was made on the pylite catalyst performance, and reactivity of the category A coal assumed in the demonstration device. (NEDO)

  3. Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

  4. Report on survey/research on energy-related elementary techniques; Energy kanren yoso gijutsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The survey/research project is implemented for establishing environment-compatible energy systems in urban areas by constructing wide-area heat supply networks to exchange energy among cities. This project studies, taking Kanagawa Pref. as the model area, distributions of unutilized energy sources, and possibilities of their utilization for heat supply. There are large quantities of unutilized energy, including waste heat from power plants, general works and cleaning works, and low-temperature waste heat from, e.g., sewage and pumping systems. The district air conditioning promotion areas are selected from those consuming large quantities of heat energy in the prefecture, and their characteristics are grasped. The effects of the networks on total energy consumption of the entire prefecture are estimated for the cases of introducing the district air conditioning systems or wide-area heat supply networks in these selected areas. Introduction of optimum advanced heat utilization systems in stereotyped areas is also considered, in order to predict the effects of introduction of wide-area heat supply networks. (NEDO)

  5. Report of regional new energy vision for Kannami Town; 2001 nendo Kannami cho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For promoting the introduction of new energy and for enhancing people's consciousness of such at Kannami Town, Shizuoka Prefecture, surveys and studies were conducted involving the energy consumption structure of the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The town consumes approximately 5-million GJ/year, with the industrial sector consuming 47%, the transportation sector 29%, and the residential and commercial sector 26%. When a comparison is made, the percentages of the residential/commercial and transportation sectors are relatively higher than the national average. Projects for new energy introduction were studied, which involved photovoltaic power generation for the town office, community hall, primary and junior high schools, nursery schools, and general residences; solar heat utilization for public facilities, greenhouses, and general residences; wind power generation for sightseeing facilities, public gardens, and emergency evaluation areas; utilization of sewage waste heat for the sewage purification center; utilization of hot spa waste heat in the urban area; a biomass-fueled power plant; medium- and mini-scale hydroelectric power generation for the drinking water treatment plant; refuse-fueled power generation at refuse incineration facilities; use of clean-energy automobiles; natural gas-fueled cogeneration for public organizations; and so forth. (NEDO)

  6. New energy vision of the Gushikami Village area; 2001 nendo Gushikami son chiiki shin energy vision sakutei tou jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Gushikami Village, Okinawa Prefecture, an investigational study was conducted of the energy demand of the village, existence amount of new energy, plan for new energy introduction, etc., and a vision was worked out. The energy demand of Gushikami Village was estimated at 640.2 x 10{sup 6} MJ/y. By sector, it consisted of 37.1% in the transportation sector, 32.0% in the commercial/residential sector and 30.8% in the industrial sector. The rate of energy source was 73.7% of petroleum-base fuel and 26.3% of electric power. As the plan for new energy introduction, the following were studied: introduction of photovoltaic power generation to the village office/museum/elementary school/junior high school, introduction of solar heat utilization facilities to the meal providing center/gymnasium, introduction of wind power generation to the sports park, project of wind power generation on the sugar cane hill (600kW x 6 turbines), cogeneration by composting of stockbreeding waste and methane, introduction of clean energy car to official vehicle, introduction of natural gas vehicle, installation of experimental plant for conversion of sugar cane to methanol, etc. (NEDO)

  7. FY 1998 R and D project on industrial science technology; 1998 nendo ryoshi kino soshi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The R and D on quantum functional devices (QFDs) were conducted, and the FY 1998 results were summed up. In the comprehensive survey on QFDs, the following were carried out for the efficient R and D promotion: R and D progress state survey/problem extraction/analytical study, technical trend survey, overseas survey ordered from overseas supplier, common basement technology study, etc. In the R and D on technology for QFDs, integration of multivalued logical devices using tunneling control functional devices, integration of logical memory devices using quantum levels, integration of quantum band combination-type multi-functional devices, silicon insulating film tunnel memory devices, assembly quantum dot functional memory, quantum wave switching functional devices, integration of single electron logical devices, integration of CMOS combination-type single electron devices, etc. Moreover, in the development of the basement technology of single electron devices, technology to construct element devices using quantum functions, basement technology of single electron device integration devices, architecture of single electron device information processing circuit system, etc. (NEDO)

  8. Report on new energy vision at Hinase Town area; 2001 nendo Hinase cho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    With an objective of accelerating introduction of and uplifting consciousness on new energies at Hinase Town in Hyogo Prefecture, investigations and discussions were given on the energy demand, quantity of new energies available, and the new energy introduction projects for the town, thus a new energy vision was established. The estimated amount of energy consumption in Hinase Town is 242,814,320,000 kcal in fiscal 2000. The amount of carbon dioxide discharge associated therewith is 76.57 t-CO2/year. Regarding the energy consumption by departments, the industrial department consumes the most, followed by the transportation department, civil household department, and civil business department. The new energy introduction projects have discussed servicing of the bio-gas plant utilizing organic wastes and cogeneration, the new energy introduction projects for the Natural Energy Island at Kakui Island and the ocean ranch consisted of the use of solar heat water warmer, solar cell powered street lights, photovoltaic power generation, and electric cars for sightseeing visitors, the Eco-school promotion project for primary schools, introduction of energy saving devices into the town office, and the new energy proliferation and enlightenment project. (NEDO)

  9. Report on the FY 1999 basic research on intelligent structure; 1999 nendo kozo chinoka no kiso kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A concept of a system is constructed in which a series of the flow from the construction of structures to the shape and control in structural phase, repair, and dismantlement is made effective and controllable by giving a function of intelligent structure to structural systems in aerospace/architecture/civil engineering fields. For it, fundamental technologies required for the systems were extracted for construction of the technology system. Further, in relation to the intelligent machinery system including the control method, manipulation, and communication of the structure under the micro-gravity environment required for this system, the basic experiment was conducted at the ground gravity-free experimental center to acquire the effective data. As to the base technology, three fields were studied of the intelligent machinery system including the behavior/control of materials and structure, intelligent robot, and communication. In the experiment on micro-gravity environment, experiments were carried out on the behavior of micro-gravity rover for small planetary probe, inter-satellite group communication, capture of trouble-satellite, development of inflatable structure, and hopping robot. The valuable data were obtained. (NEDO)

  10. Fiscal 2000 pioneering research on the spintronic device basic technology; 2000 nendo spintronic soshi kiban gijutsu sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Researchers specializing in technologies of magnetism or semiconductor were drafted from the industrial, official, and academic circles, who conducted hearings, patent investigations, overseas surveys, and the like, concerning spintronics. Collected in this report are the outline of the research and development of spintronic device technology, its current state and tasks and its importance from social and economic viewpoints, and the strategy that Japan should follow in the research and development of the technology. Important spintronic device technologies now attracting attention are mentioned below. The nonvolatile magnetic memory device MRAM (magnetic random access memory) is supposed to be the device which will enjoy practical application first among like devices. It is expected that the spin conduction device will lead to novel functions when the possibilities of the spin-dependent electric conduction phenomenon are further pursued. It is hoped that the spin optical device will be used as a light isolator, light spin logic device, field induced variable wavelength laser device, spin laser device, high-speed light switch, and so forth. It is necessary to watch the development of a spin-aided quantum computer which is still at the stage of basic study. (NEDO)

  11. Fiscal 2000 achievement report. Welfare technosystem research and development (Niihama); 2000 nendo walfare technosystem kenkyu kaihatsu (Niihama) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop welfare equipment systems for helping people needing care lead an independent life. In collecting data on the transfer of patients and carrying out research and development in this connection, activities are conducted to develop (1) a transfer wheelchair and a transfer aiding wheelchair, (2) a simplified transfer type toilet, and (3) a tilt mechanism installable on a standard wheelchair. Under item (1), a wheelchair and an auxiliary wheelchair enabling the transfer of a person who cannot move without help between a wheelchair and an automobile are experimentally built. Under item (2), a simplified transfer type toilet to which a single attendant can easily guide the patient from the bed is developed. Under item (3), a tilt mechanism is developed, installable on a wheelchair to recline the same for the aged person to assume a comfortable attitude. In the development of a portable character reading device, a finger tip reader was experimentally manufactured for reading Japanese characters. (NEDO)

  12. Report on a survey in fiscal 1999. International study exchange project; 1999 nendo kokusai kenkyu koryru jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Exchange with overseas researchers and research organizations has important significance in promoting research and development toward creating new research areas and structuring new technological systems intended for solving global environment problems. In cooperation with RITE and RITE researchers and relevant learned societies, researchers were invited or dispatched to international conferences and international symposiums with regard to global environment related technologies. In addition to interaction with major overseas research institutions and universities, medium and long-term dispatch and invitation have been performed that are considered to play an important role in future research exchange activities based on the achievements of short-term invitations and dispatches and examinations with potential research exchanges. As a result, domestic and overseas interactions on the latest researches were performed, while basic and applied researches related to global environment technologies are being proceeded also in various areas of studies outside the country. It was identified that these exchange activities have close relationship with research and development of industrial technologies serving for global environment preservation, which are being promoted by RITE. (NEDO)

  13. Fiscal 2000 study on technology and marketability concerning phytoremediation; 2000 nendo phytoremediation ni kansuru gijutsu oyobi shijosei no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigative study was conducted on phytoremediation with the purpose of correcting soil contamination caused by heavy metals and the like. In Japan, in connection with the cadmium pollution along the Jintsugawa River region in Toyama Prefecture, a growth of botanical colony such as Athyrium ykoscense was confirmed having a high capacity in absorbing/accumulating heavy metals, with a possibility suggested that they may be utilized for phytoremediation. In a technological research for restoring the environment sustainingly in a wide area, feasibility has been proven to remove polluting agricultural chemicals in farmlands and toxic substance in old industrial sites by making forest trees like poplars, lawns and herbage function. In a project for the cleanup of oil contaminated soil after Gulf War, a demonstrative test of bioremediation for one hectare was performed and, after 15 month experiment, 80 to 90% of aliphatic compounds and 50 to 60% aromatic compounds were degraded. In EU Framework Program in Europe, phytoremediation projects have been implemented across the member countries. (NEDO)

  14. Fiscal 2000 achievement report. Welfare technosystem research and development (Sapporo); 2000 nendo Welfare technosystem kenkyu kaihatsu (Sapporo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Activities are conducted on system technologies for ensuring comfortable living circumstances and thereby helping aged or handicapped people live independently in snowy cold regions. The research and development efforts center about the three fields of (1) in-house systems to help aged or handicapped people live an independent life, (2) in-home care equipment systems suitable for advanced welfare oriented residences, and (3) user interface controllers to improve on operating sensation in a motor driven wheelchair. In field (1), studies involve the development of low floor residences for snowy cold regions, improvement on entrances for independent residences helping the inhabitants lead an independent life, and functionally excellent designs for handrails for steps, stairs, or bathrooms. In field (2), surveys are conducted concerning design improvements and their acceptability relative to a universal welfare equipment controller, optimum sound that welfare equipment alarms should produce, and transfer devices. In field (3), studies are made about motor driven wheelchair controllers. (NEDO)

  15. Report on a regional new energy vision establishment in Yatsuka Township; Yatsukamachi chiiki shin energy vision sakutei jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys and discussions were given on establishing a new energy vision in Yatsuka Township in Shimane Prefecture. For the survey on available amount of natural energies (sunlight and wind), all-weather insolation required for solar energy power generation was analyzed by using the NEDO information, and wind was analyzed based on observations at Matsue Meteorological Observatory, Sakai-minato Observatory, and Nakaura Water Gate. In discussing the system, power generation amount in the Matsue area was estimated for the case when solar cells of single crystal silicon plus amorphous hybrid type HIP-H48B1 are used. For wind power generation, power generation amount was calculated from observation values derived at the Nakaura water gate when wind mills with diameters from 2 to 10 m are used. Furthermore, calculations were performed on power amount generated uniformly by using a hybrid system using solar energy power generation and wind power generation. As a result of the discussions, a plan was established to introduce the new energies by means of a solar and wind energy hybrid power generation system to the greenhouse 'Green Stellar' symbolizing the Japan's largest peony production, being capable of year-round peony cultivation. The system is planned to be introduced to the town office building and other public organizations sequentially according to annual programs. (NEDO)

  16. Workshop on APEC virtual center for environmental technology exchange; APEC kankyo gijutsu koryu virtual center workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    At the 'policy maker workshop of the virtual center of APEC technology exchange' held in November 1997 in Osaka, Japan, it was agreed to organize study groups to discuss the scope of information provided by the virtual center, and to make common the classification systems and retrieval functions. In addition, the necessity was confirmed on international cooperation to promote establishment of virtual centers in different countries and territories. On the first day, Professor Ueda at the Kyoto University gave the basic lecture entitled 'global environment preservation and environmental technology transfer: problems and prospects'. Mr. Dan, the workshop manager gave the basic proposal entitled 'the future directionality of environmental technology exchange inside the APEC territories by using Internet'. Based on the basic proposal made on the first day, reports and discussions were given in the following sessions, where confirmation was made on the future directions. S1: establishment of the virtual centers in other countries and territories; S2: assurance of interchangeability of classification systems and retrieval functions in providing information, and S3: presentation of examples of inter-territorial exchange and the future directionality. (NEDO)

  17. Trend of advanced technology of micromachines in the USA; Beikoku ni okeru micro machine sentan gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In this research, the data of advanced technology of micromachines in the USA have been searched, collected, and arranged from the US patent information, technical journal information, and newspaper and general journal information. According to demand, the main undertaking information was interviewed from well-informed persons. The data were compiled as advanced technology trend of micromachines in the USA. Sensors are remarkably predominant in the elemental technology. There are also important topics in the fields of actuators, motors, lenses, devices, and structures. On the other hand, materials, etchings, packages, motive powers, and softwares are also important elemental technology in spite of their less information. From the viewpoint of usage, detection systems are remarkably predominant. Then, robots, processing systems, optics, analysis systems, motive power systems, medical systems, and acoustic systems are also important. From the viewpoint of industrial sector, the environmental items are predominant. Automobiles, medical treatments, and information communications follow the above. When new relationships to the secondary usage and tertiary usage are not found, it would be rather hard to express such a technology development trend more clearly.

  18. Achievement report on developing inverse manufacturing system in fiscal 1998; 1998 nendo inverse manufacturing system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a circulating type production system, or an inverse manufacturing system, to minimize the environmental load in the entire life cycle of industrial products from design to manufacturing, maintenance, recovery, and re-utilization. In developing the recycling information system, discussion and extraction were executed on the data to be exchanged between manufacturers and users in the inverse society. A new individual parts history control system was developed. In developing the recycling processing system, a prototype system was evaluated by using hypothetical data, wherein the possibility of improving the recycling processing efficiency and reducing the cost was verified. In addition, trial design was made on a recycling processing plant in consideration of the cost effect to get the future plant image. In fabricating the inverse manufacturing products, a prototype concept model was made for information terminal devices. Development was performed on such elementary technologies as the easy-to-disintegrate structure technology, self-integration connecting structure and environmental hysteresis detection system. (NEDO)

  19. FY 1999 report on the results on analysis of protein functions; 1999 nendo tanpakushitsu kino kaiseki seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at construction of the intellectual infrastructures for biotechnologies, in order to accelerate development of the Japanese technologies and activate their application to industries. Described herein are the FY 1999 results. These infrastructures are for functional analysis of protein which will be one of the key issues in genome analysis, and collection and analysis of biological information. This project includes a total of 9 research and development themes for four research categories: frequency analysis of gene expression (development of the gene expression profile database system for functional analysis of human genome, and analysis of the gene expression and protein functions by the ECA chip technology), function analysis by the biological model (high-performance analysis by the bio-project, database system for drug metabolizing enzymes, analysis of gene functions using mutant mice, and simple genome function analysis of murine individuals using the RNAi effect), protein expression (function validation of unknown human genes based on the useful biological model, and protein function analysis using multi-purpose destination vectors), and protein function prediction by the information science method. (NEDO)

  20. Report on the environmental safety evaluation sub-committee meetings in fiscal 1987; 1987 nendo kankyo anzensei hyoka bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The environmental safety evaluation sub-committee has held two meeting in the current fiscal year as described below. The first sub-committee meeting (August 25, 1987) was held for the agenda of the summary of future test plans, the result of overseas surveys in fiscal 1986, the results of tests in fiscal 1986, and the summary of the test plan for fiscal 1987. The major agendum of the second sub-committee meeting (February 23) was the interim reports on the overseas survey results and the safety tests in fiscal 1987. NEDO intends to ensure the labor hygiene for workers in coal liquefying plants, the effect of liquefied oil on users' health, and social acceptability of liquefied oil. Therefore, a safety test for liquefied oil in the primary hydrogenation process was performed provisionally on brown coal PP in the initial stage of operation, in addition to bituminous coal liquefied oil at the existing 1-t/d PDU. The main contents of the test performed by NEDO are based on the labor safety and hygiene law and the law related to regulation on the deliberation and manufacture of chemical materials. Different tests using guinea pigs were carried out on the total fraction mixed at the 1-t/d PDU, and each fraction of light and heavy oils, where the liquefied oil was verified to have minor degree of toxicity. (NEDO)

  1. Achievement report for fiscal 1982 on Sunshine Program. Coal energy; 1982 nendo sunshine keikaku seika hokokusho. Sekitan energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-07-01

    This research program consists of (1) the solid catalyst-aided reforming of various petroleum based oils and heavy coal oils into Solvolysis solvents and the secondary hydrogenolysis, (2) a search for pre-treatment for improvement on the sub-bituminous coal liquefaction yield, and (3) a search for measures for improvement on the brown coal liquefaction yield. Studied in this fiscal year are (1) the high-temperature short-contact time liquefaction of brown coal, (2) the role of catalyst support for selective upgrading of SRC (solvent refined coal), and (3) reforming of thermal melting feature of low rank coal by preliminary deashing at room temperature. In relation with Item (1), it is found that the dehydrogenation or reaction to carbonization of molecules involved in hydrogen donation is structure-sensitive but that thermolysis of coal is accelerated under high-temperature conditions to allow transfer hydrogen to contribute uniformly. It is deemed also that matching is excellent between hydrogen transfer and thermolysis, that the solvent dissolution level is elevated, and that the reaction short in duration inhibits consecutive polymerization reaction. These are supposed to be effective in improving on the liquefaction yield and in rendering heavy constituents lighter. In relation with Item (2), it is found that the experimentally manufactured catalysts are effective in reducing the weight of heavy constituents. In relation with Item (3), a carbonization reforming method is experimentally implemented in which the ash that affects carbonization is further removed by a pre-treatment at room temperature. (NEDO)

  2. Survey report on establishing a regional new energy vision in Gohoku Village; Gohokuson chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A regional new energy vision was established in Gohoku Village in Kochi Prefecture. Significance of this vision as a guideline for new energy introduction lies in preservation of natural environment, development promotion of the district, and building of a village strong against disasters. According to the discussion on energy availability in Gohoku Village, the expected usable amount will be about 5.13 million kWh/year by using solar energy power generation, about 2.25 billion kcal/year by utilizing solar heat, about 42 million kWh/year by utilizing wind energy, about 1.07 million kWh/year by using a small hydroelectric power plant, and about 31 million kcal/year by using wastes energy. The important new energy introduction projects are planned for introducing solar energy power generation, solar heat utilization, wind power generation, and small hydroelectric power generation in the area of 'Green Park Hodono' to make it a new energy model park (an ecology park), introducing solar energy power generation and solar heat utilization in the health and welfare center, day-service center, and special aged nursing home, and introducing clean energy fueled automobiles in official use. (NEDO)

  3. 1998 Annual Study Report. Standardization of color reproduction management; 1998 nendo seika hokokusho. Iro saigen kanri (color management) no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Standardization of color reproduction management is aimed at realization of the most urgently needed areas of the color reproduction management for international standardization. This R and D program is aimed at drafting the standards for color information devices and their characteristics, and proposing the drafts. Factors which deteriorate color reproduction stability of input and output devices are classified and analyzed, devices for evaluation are selected, and extents of the deterioration are measured and evaluated, in order to extract the problems involved in the color reproduction models for the current input and output devices. Standardization of color management on the multi-spectrum color images is attempted for business printing, where effectiveness of a fluorescent ink containing a fluorescent material is noted for expansion of the color reproduction range for printing color images with the conventional YMCK inks. Basic aspects of the fluorescent colors are measured, to verify the methods for measuring fluorescent body colors. As a result, new knowledge is obtained. The standard images for flesh color evaluation are produced, and the methods for analyzing the data obtained by the tests, including the subjective tests, are established. These lead to establishment of the standards for preferred flesh color of the yellow races. (NEDO)

  4. FY 2001 report on the new energy vision of Ajigasawa Town; 2001 nendo Azigasawa machi shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Ajigasawa Town, Aomori Prefecture, an investigational study was conducted of the amount of energy demand of the town, potential introduction of new energy, etc., and a new energy vision was worked out. The population of Ajigasawa Town was 13,551 according to the results of the national census taken in 2000, which is slightly decreasing. The energy demand is broken down into 40.1% in the transportation sector, 35.4% in the industrial sector and 24.5% in the commercial/residential sector, depending on petroleum (81.8%) and electric power (13.1%). The CO2 emission amount from the above is estimated at 26,210 t-C/y in total. In the model project for new energy introduction, the following were selected: wind power generation for the filtration plant of water supply system/night soil treatment plant/funeral hall/comprehensive park/seed and seedling center; photovoltaic power generation for the trip village for youth/elementary schools; fuel cell/hybrid car for Ajigasawa town office; micro-hydroelectric power generation for nursery; natural gas cogeneration for the insurance welfare center. (NEDO)

  5. Fiscal 2000 achievement report. Welfare technosystem research and development (Mizusawa); 2000 nendo walfare technosystem kenkyu kaihatsu (Mizusawa) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For assisting aged people, healthy and living alone, in living without help, activities were conducted for (1) an electrical transmission experiment connecting residences (two, inhabited for the experiment) and a remote location (Techno-House) and (2) the development of a home server equipped with an electrocardiograph. Under item (1), data collected by sensors (occupancy sensor, open/close sensor, flame sensor, waterflow sensor) installed at the residences occupied by aged persons living alone were forwarded to Techno-House via CATV (cable television) and analyzed for the study of elderly people's behavior and daily life pattern. It was found that using this system the behavior of elderly people living alone might be detected even in the absence of their intention to report or communicate. Under item (2), an Ni-based electrode sheet was fabricated and installed in a bed and, via the sheet and a CATV channel, cardiographic waveforms were transmitted to Techno-House where the data were put into an analyzer for the examination of the elderly person's physical conditions. (NEDO)

  6. Summary report of the overseas researcher invitation program in FY1996; 1996 nendo kaigai kenkyusha shohei jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To exchange research information, Mr. Koernaen Inif was invited from the Ministry of Industry and Commerce, Indonesia in the period between 4th November in 1996 and 4th February in 1997 as a part of the overseas researcher invitation program in FY 1996. The research theme is `Investigation of low cost removal method of COD and BOD from industrial waste water: Biodegradation of lignin in the waste water from pulp industry using anaerobic bacteria.` The institute of the invited researcher has promoted investigations for improving water quality of the Surabaya River. The largest reason of the water quality pollution of the Surabaya River is caused by the waste water from paper and pulp industry, and pollutants are COD and BOD. In major factories with economic margins, waste water treatments have been conducted, which do not satisfy the waste water standard of factories. In this investigation, the treatment technology information of industrial waste water were collected. The information were summarized for contributing to the future research and development in Surabaya. The objective was to obtain the biodegradation techniques of lignin using anaerobic bacteria. 51 refs., 7 figs., 5 tabs.

  7. Fiscal 1995 geothermal development promotion survey. Natural environment survey report; 1995 nendo chinetsu kaihatsu sokushin chosa. Shizen kankyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In Candidate C area for the geothermal development survey, the natural environment was surveyed and `the secondary landscape assessment` was summed up in which places proposed for drilling of large-size wells and for construction of power generation facilities are extracted and a simulation of the landscape is conducted. The area for survey is the Shiramizu-gawa region in the south of Lake Akan, Akan-cho, Akan-gun, Hokkaido. The field survey was carried out about three items of landscape, plants and animals during the June-November period, 1995. As to the flora, diverse florae including vegetation unique to alpine areas, wetlands, and fumarole surrounding areas were found in the region, which is covered with summer-green broad-leaved forests or mixed forests of coniferous and broad-leaved trees. As to the fauna, faunae inhabitant of the highly natural forests were found including black woodpeckers and mountain hawk eagles. As a result of studying the places proposed for geothermal development from the above-mentioned survey, two places were picked up in the west of the survey area, where geothermal development is comparatively less influential in the natural environment and landscape and there is a high locational adaptability. 19 refs., 56 figs., 49 tabs.

  8. Fiscal 2000 pioneering research report on the 3D nanotechnology; 2000 nendo 3D nano technology sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted of the 3D nanotechnology which is a technology that aims to create novel functions and to enhance functions in mechanical engineering through the control of large-area 3-dimensional nano-scale structures. In this fiscal year, trends of research and development and technological tasks were surveyed from the viewpoint of nanomanufacturing technology. Basic processing technologies were surveyed, which included the laser-aided or light-aided micromachining technology, chemomechanical processing technology, and nanoparticle beam-aided processing technology. In the research of mass production technologies, the nanostructure transfer technology superior in capability to the conventional photolithography was taken up. Nanomanipulation technologies were also surveyed, such as atomic/molecular-level observation, assessment, processing, fixation, and the like. Technologies involving machine elements and structures were surveyed, when microactuators and micromechanisms were studied, such as nano-scale functional films. Lastly, a proposition was made about research and development tasks for the future and about how to work on such tasks. (NEDO)

  9. Report on a comprehensive research study (home welfare apparatus system - lifestyle); Sogo chosa kenkyu (zaitaku fukushi kiki system - lifestyle) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    An investigational study was conducted on evacuation of aged people at disaster, life maintenance, and welfare apparatus which is applicable to the future change of life style and its harmony with the living environment. In the study of care apparatus, reported were the apparatus operational interface using the indoor environmental control simulation system, safety on moving/transfer equipment, experiment on opening/closing power of sliding doors, study of electric-driven wheel chairs, study of the sitting pressure of various wheel chairs, etc. In relation to the living environment, the paper reported planning of houses introducing care apparatus, assessment of system kitchen, disaster prevention measures for aged/handicapped people, study on performance of the combined use in the living environment, assessment of drops in floor level in the living space, etc. Also reported were assessment on the living environmental control state of serious paralyzers of the limbs, study of a network to support care at home, etc. 48 refs., 117 figs., 29 tabs.

  10. FY 2000 report on the results of the Clean Energy Festa; 2000 nendo clean energy festa kekka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For understanding/education for the spread of clean energy vehicles and promotion of recognition/understanding of new energy, the Clean Energy Festa was conducted in Yokote, Akita prefecture, Nagoya, Osaka, Yokohama and Hiroshima, and analysis by questionnaire survey was made. Written below were the details of the questionnaire survey. How you knew of the exhibition: 'by leaflets from school, etc.' is 50.4%; why you came to the exhibition: 'there is something enjoyable about it' is 32.5%; What attracted you: 'solar car workshop' is 34.8%; How much you have known of new energy: 'somewhat known' is 41.5%; How much you understood new energy after seeing the exhibition: 'somewhat understood' is 60.9%; How much you became aware of new energy: 'a little deeply aware' is 59.8%; How much you understood clean energy car after seeing the exhibition: 'somewhat understood' is 58.7%; How much you became aware of clean energy car: 'a little deeply aware' is 60.9%. (NEDO)

  11. Geothermal development promotion survey. No. B-3 Kumaishi area; Chinethu kaihatsu sokushin chosa seika hokokusho. No. B-3. Kumaishi chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper summarizes the result of a geothermal resource survey carried out from fiscal 1995 through fiscal 1997 in the Kumaishi Area located in the western center of Oshima Peninsula in the south western part of Hokkaido. The survey for this area was performed with an objective to search the spread of high temperature area continuing from the adjoining Yakumo area where the highest temperature of 233 degrees C has been confirmed in a structural test well (N63-YK-6), to identify high water permeating areas in great depth points underground, and to find possibility of existence of geothermal resources. The survey included geological and alteration zone survey, geochemical survey, gravitation exploration, electromagnetic exploration, drilling and temperature logging of five structural test wells, water injection test, temperature restoration test, core survey and hot water survey. Also performed were environmental effect survey, rock age measurement, alteration age measurement, and fluid inclusion test. As a result of the survey, it was identified that the verified geothermal hot water has been stored in granites with poor water permeability, whose low temperature has not formed convection systems spreading in wide areas despite having been heated, making each system exist in small scale independently. It was estimated that the possibility is low to expect geothermal power generation. (NEDO)

  12. Report for fiscal 1998 on feasibility study for introduction of electric automobiles; 1998 nendo denki jidosha donyu kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys have been made on the characteristics of environmentally harmonizing automobiles, and the status of development and introduction thereof inside and outside the country. Discussions were given on the possibility of introducing electric automobiles in Japan. In developing environmentally harmonizing automobiles in Japan, works have been executed on low pollution type components such as lean burn engines, electric automobiles, gasoline engine and electric motor hybrid cars, methanol fueled cars, and fuel cell automobiles. Some of them are already in use in spite of their high price. In America, a cooperation project for the next generation cars has been implemented by mobilizing industrial, academic and governmental organizations. Based on the achievements thereof, the car makers have announced their original advanced cars respectively. In the EU, development of low exhaust gas cars and zero emission cars is being carried out jointly by the related industries setting years 2003 to 2005 as the target. An urban type traffic system utilizing electric vehicles, and a traffic system dividing movements of short distance and long distance are proposed as the means to introduce the future electric automobiles. (NEDO)

  13. Fiscal 1997 achievement report. Research and development of synergy ceramics; 1997 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development is conducted on two subjects, that is, 1) hyper organized structure control technology and 2) structural element control technology. In addition, joint research and development is conducted on the creation of new materials by hyper organized structure controlling, hyper organized structure controlling for ceramics by a structurization reaction process, designing of precursors to ceramics, and the hyper organized structure control for ceramics by nanostructure process control. The joint research and development endeavors further deal with re-entrusted projects which involve researches on sintered structure control by powdery particulate structure control; dynamic process of synergy ceramics; oxynitride liquids, glasses, and glass-ceramics; and multifunctional ceramic laminates for engineering applications. Under subject 1), researches are made on the development of precursors into ceramics by utilizing chemical reactions of organic metal compounds, and analyses are conducted into the effects, exerted by the molecular structures of precursors and the conditions of a reaction for their development into ceramics, on the microstructures and various properties of the ceramics to be composed. Under subject 2), high strength, great hardness, and high resistance to wear are realized by allowing the precipitation of nano-particulates in crystals of a fine and very compact sintered body of alumina. (NEDO)

  14. Fiscal 1974 research report. General research on hydrogen energy subsystems; 1974 nendo suiso riyo subsystem sogoteki kento hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    Based on the contract research 'General research on hydrogen energy subsystems and their peripheral technologies' with Agency of Industrial Science and Technology, each of 7 organizations including Denki Kagaku Kyokai (Electrochemical Association) promoted the research on hydrogen energy subsystem, combustion, fuel cell, car engine, aircraft engine, gas turbine and chemical energy, respectively. This report summarizes the research result on the former of 2 committees on hydrogen energy and peripheral technologies promoted by Denki Kagaku Kyokai. The first part describes the merit, demerit, domestic and overseas R and D states, technical problems, and future research issue for every use form of hydrogen. This part also outlines the short-, medium- and long-term prospects for use of hydrogen and oxygen energy, and describes the whole future research issue. The second part summarizes the content of each committee report. Although on details the original reports of each committee should be lead, this report is useful for obtaining the outline of utilization of hydrogen energy. (NEDO)

  15. Report on the comprehensive investigational research (at-home welfare apparatus system); Sogo chosa kenkyu (zaitaku fukushi kiki system) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    An investigational study was conducted on the research and development of an at-home welfare apparatus system. In this study, a stay experiment was carried out on whether aged or handicapped people can easily live in welfare houses into which at-home welfare apparatus was integrated, using high-tech at-home nursing apparatus systems (welfare techno house: WTH) which were installed at seven places in Japan based on `the development of a system supporting independent excretion.` In addition, the following were conducted: experiments on at-home welfare apparatus in terms of the evaluation of performance/operability/safety, physical physiology reactions, nursing burden/estimate of independence, two-way communication, examination of housing environments, etc. In WTH Chofu, a test on evaluating welfare apparatus was conducted by people with limbs paralysis and healthy case workers. In WTH Sapporo, by a working group studying biological information, examinations were made on the situation of standing up of healthy adults, old people and people with paralysis of one side of the body from various types of chairs, beds, wheel chairs, portable toilets and sitting down on them. An examination was also made on harmony with psychological function and physically adaptable function by a working group studying at-home nursing apparatus. 75 figs., 15 tabs.

  16. Research report of innovation of industrial technology in FY 1996; 1996 nendo sangyo gijutsu no innovation chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Remarkable innovations of the Japanese industry in various fields have been extracted and evaluated during the 50 post-war years. In this report, a method of capturing the innovations of industrial technology is examined. It is essential to clarify the social role of industrial technology, and the original views of this research are indicated by focusing on the innovation process in order to clarify the connections between those of mutual industry, technical management, man-power, and unique Japanese technology. The innovations achieved by the Japanese industry during post-war 50 years are classified into eight categories, i.e., automobiles, iron, aero-space/railways, machines, national land/energy, chemicals/fine ceramics, electronics/information/communication, and life, to clarify the technological progress in each field. In Japan, the industrial technology has been developed with learning from fundamental researches in Europe and the USA. In the future, it is necessary to independently develop industrial frontier. 4 figs., 47 tabs.

  17. Basic survey report on regional new energy vision for Ehime Prefecture; Ehimeken chiiki shin energy vision kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision has been formulated to establish guidelines for popularizing and utilizing new energy which generates but a small amount of environmental impact. The results of surveys conducted in this connection are described in five chapters, which cover (1) the trend of new energy, (2) current situation of new energy in Ehime Prefecture, (3) calculation of the existing amount and available amount of new energy, (4) calculation of the introducible amount of new energy, and (5) the basic policy toward the introduction of new energy. Part (4) covers solar energy, wind energy, waste-derived energy, temperature difference energy, minor scale hydroelectric power generation, biomass energy, and like others. It states that a total of 540,000 kl/year will be available in terms of oil, equivalent to approximately 6% of Ehime Prefecture's 1997 energy consumption, and that it is expected that in fiscal 2010 photovoltaic/passive solar energy utilization, cogeneration, and wind power will yield 152,000, 314,000, and 27,000 kl/year respectively. (NEDO)

  18. Summarized achievement report on the Sunshine Project in fiscal 1980 (Hydrogen energy); 1980 nendo seika hokokusho gaiyoshu. Suiso energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-04-01

    This paper summarizes the achievement report on the Sunshine Project in fiscal 1980 for hydrogen energy research. In hydrogen manufacturing using the electrolytic process, improvements were made on membranes and electrodes. Solid electrolyte electrolysis is also under research. Researches are continued on reaction, separating operation, and device materials for the iodine system cycle in the thermo-chemical method. In the iron system cycle, a reaction experimenting equipment was fabricated on the trial basis, and tests and evaluation were performed on the material and heat balances. In the mixed system cycle, researches on the light irradiation electrolytic process were continued, whereas the light collecting rate was raised by using a lens to increase light intensity, having enhanced successfully the reaction rate to 60 to 80%. A heat diffusion column for HI decomposition and separation (hydrogen acquisition) was discussed in terms of chemical engineering. Development works are continued on metal hydrides for hydrogen transportation, and durability tests are also being performed. Same applies to hydrogen storage. A model burner was fabricated on the trial basis, and catalytic combustion was studied as development of a combustion technology that matches the requirements for safe hydrogen combustion and suppression of NOx emission. Searches were continued on catalysts and solid electrolyte materials for fuel cells. Thin film sold electrolyte fuel cells constructed by using the evaporation process are also being studied. The paper also describes measures for hydrogen safety assurance and researches on energy systems. (NEDO)

  19. FY 1988 report on the committee of the Coal Gasification Committee; 1988 nendo sekitan gaska iinkai hon'iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    The paper reported activities of the committee of the Coal Gasification Committee in FY 1988. In the 1st committee meeting, report/discussion were made on the outline of the FY 1988 research plan on the coal gasification technology development. The distributed data were those on the development of entrained bed coal gasification power generation plant (the state of the development of a 200t/d gasification power generation pilot plant), the results of the operation using entrained bed coal gasification equipment, development of coal utilization hydrogen production technology (design/construction of pilot plant) and development of coal utilization hydrogen production technology (support study of pilot plant, study using small equipment). In the 2nd committee meeting, report/discussion were made on activities of sections such as the gasification power generation section and gasification technology section and the state of progress of the coal gasification technology development. The distributed data were those on the development of an entrained bed coal gasification power generation plant, support study of the development of an entrained bed coal gasification power generation plant, etc. (NEDO)

  20. Interim evaluation report on research and development of automatic sewing systems; Jido hosei system no kenkyu kaihatsu chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The research and development project for automatic sewing systems is aimed at establishing the techniques necessary for developing (automatic sewing systems) which efficiently produce diversified types of products in small quantities, to cope with various requirements, e.g., diversified consumers' needs and reduced cycle periods. This project covers R and D of the sewing preparation/processing, sewing/assembling, cloth handling, and system management/control techniques. The program for developing the total systems and elementary techniques draws the conceptual designs of their functions, performance and shapes, to outline the overall R and D project. The programs for the individual elementary techniques include studies on their basic functions and performance; design works from the basic designs to determine the specifications to the detailed designs of the devices to be developed; construction of the test units on a trial basis; and function confirming tests to confirm operability of the unit components and device performance, where these works are simultaneously implemented. This paper describes the interim results of evaluation of the elements developed for the elementary techniques, summarizing the results obtained so far. It is concluded that most of the targets of the R and D themes are sufficiently achieved by the end of FY 1987, and that the project can be now advanced to the next phase, construction of the test plants. (NEDO)

  1. Report of results of contract research. 'Research on magneto hydrodynamic (MHD) generation'; MHD hatsuden system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    Examination was conducted in detail on an MHD generation system by coal combustion, with the results reported. Concerning a gas table calculation program in coal combustion, it was prepared assuming 100% slag removal ratio in the combustor as the primary approximation. A combustor for MHD generation needs to efficiently burn fuel using high temperature pre-heated air as the oxidant, to fully dissociate/electrolytically dissociate seed, and to supply to the generation channel a high speed combustion gas plasma having a high electrical conductivity which is required for MHD generation. This year, an examination was conducted on technological problems in burning coal in an MHD combustor. As for the NOx elimination system in an MHD generation plant, an examination was made if the method studied so far in MHD generation using heavy oil as the fuel is applicable to coal. Also investigated and reviewed were various characteristics, change in physical properties, recovery method, etc., in a mixed state of seed and slag in the case of coal combustion MHD. (NEDO)

  2. International Workshop on Carbon Cycling and Coral Reef Metabolism; Sangosho no tanso junkan ni kansuru kokusai workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-16

    The paper described the International Workshop on Carbon Cycling and Coral Reef Metabolism which was held at Miyako-jima, Okinawa Pref. on October 17-24, 1995. In the workshop, researchers got together which are involved in marine chemistry, marine biology, coral ecology, and environmental science, and discussed the carbon cycling and metabolism of coral reef. Discussions were made on what the coral reef ecosystem is, and what the definition of a sink or a source for CO2 is. Also discussed were scales of how much time and space should be considered to make these issues clear. Further, it was proposed that it was necessary to investigate carbon balance of both the whole system and the components of the system and to keep track of mass transfer among neighboring components of the system. Seventeen presentations were given. The workshop obtained a definite consensus on carbon balance of the coral reef system. 123 refs., 39 figs., 9 tabs.

  3. Survey research report by the hydrogen occluding alloy utilization development committee; Suiso kyuzo gokin riyo kaihatsu iinkai chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    This report summarizes the FY 1984 survey research results, issued by the hydrogen occluding alloy utilization development committee. The basic property subcommittee is responsible for collecting published data related to the basic properties of metal halides as much as possible, and pigeonholing them to have the data which can contribute to development of the new alloys for basic researches and engineering applications of hydrogen occluding alloys. The subcommittee members have collected these data. The common theme subcommittee has planned to collect the P-C-T diagrams of the hydrogen occluding alloys and new alloys as much as possible, for the designs, development, production and system designs of the hydrogen occluding alloys. The P-C-T diagrams have been collected for a total of 340 types of alloys, which fall into the broad categories of Mg-based, TiFe-based, TiMn-based, other Ti-based, rare-earth-based, Zr-based, Ca-based and others. The analytical methods have been also investigated while collecting P-C-T diagrams. (NEDO)

  4. Workshop on APEC virtual center for environmental technology exchange; APEC kankyo gijutsu koryu virtual center workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    At the 'policy maker workshop of the virtual center of APEC technology exchange' held in November 1997 in Osaka, Japan, it was agreed to organize study groups to discuss the scope of information provided by the virtual center, and to make common the classification systems and retrieval functions. In addition, the necessity was confirmed on international cooperation to promote establishment of virtual centers in different countries and territories. On the first day, Professor Ueda at the Kyoto University gave the basic lecture entitled 'global environment preservation and environmental technology transfer: problems and prospects'. Mr. Dan, the workshop manager gave the basic proposal entitled 'the future directionality of environmental technology exchange inside the APEC territories by using Internet'. Based on the basic proposal made on the first day, reports and discussions were given in the following sessions, where confirmation was made on the future directions. S1: establishment of the virtual centers in other countries and territories; S2: assurance of interchangeability of classification systems and retrieval functions in providing information, and S3: presentation of examples of inter-territorial exchange and the future directionality. (NEDO)

  5. Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1982 reported. This year is the final year of this research; therefore, reexamination was made from the practical standpoint on the R and D of coal fired MHD generation, evaluating the present technological level as well as clarifying the development procedures, with proposals made as to the R and D from now on. The present technological level in the practicability is still in the basic stage, where the essential problem is the development of combustors, air heaters and generation channels in particular. An examination was conducted for the problems, procedures and period of the development for each component equipment, with the results provided as materials for studying the path to the experimental plant of 100 MW heat input. In the method of proceeding with the R and D in the future, it was decided as essential, in order to enter the stage of the experimental plant from the element technology development, that R and D is carried out on the unestablished component technology, making sure that no excessive risk is taken in scaling up to the next stage. (NEDO)

  6. Report on new energy vision for fiscal 2000 in Nanno Town (Gifu Prefecture); 2000 nendo Nannocho shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established in Nanno Town, upon investigating the existence quantity and utilization possibility of new energies, and from a viewpoint of reduction of air pollutants, and assurance of independent energy resources. The vision was established with the residents' participation as the base, while keeping consistency with the 'Nanno Town's new century development plan, 2010'. The activity achievements were put into order by the following six items: 1) necessity of introducing new energies, 2) the current status of Nanno Town, 3) energy demand quantity in Nanno Town, 4) possibility of introducing the new energies, 5) establishment of the introduction project, and 6) assignments and measures toward realization of the vision. Item 4) is composed of the summary of new energies in the district, new energy existence quantity in Nanno Town, and the residents' consciousness. Investigations were carried out on utilization possibilities of energies from solar beam, wind power, bio-mass, and wastes. The new energy existence quantity is estimated to be 5,005 kl/year converted into petroleum, as solar heat for general houses, 1,132 k/year as bio-mass, and 329 k/year as wastes. (NEDO)

  7. FY 1981 Report on the results of Sunshine Project. Coal energy; 1981 nendo sunshine keikaku seika hokokusho. Sekitan energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-07-01

    This report presents the results of (researches on solvolysis liquefaction mechanisms and reaction promotion with oil- and coal-based solvents), conducted as part of the research and development project for coal liquefaction techniques. The FY 1981 program includes researches on (1) the effects of liquefaction reaction conditions on liquefaction yield and production of light products for coal species of low degree of carbonization, including brown coal, (2) the effects of pretreatment of coal on its liquefaction reactivity, and (3) up-grading of the solvolysis coal liquid (SCL). For the item (1), HA240 (hydrogenated Ashland's A240) is used to investigate its liquefaction capacity for various coal species of low degree of carbonization, including brown coal. For the item (2), the effects of pretreatment in a hot water bath with reflux was investigated for sub-bituminous coal in the FY 1980. In the FY 1981, various pretreatment methods are attempted for enhancing liquefaction reactivity of brown coal. As a result, it is found that ash content of brown coal is decreased to one-third of the initial level, when it is treated in a diluted hydrochloric acid bath with reflux. For the item (3), SCL hydrogenated by Birch reduction (B-SCL, 1) is compared with H-SCL with respect to properties, structures and thermal crackability, to discuss the items required for the catalyst to be used in the second stage by clarifying effectiveness of the catalyst. (NEDO)

  8. Fiscal 2000 achievement report. Welfare technosystem research and development (Chofu); 2000 nendo welfare technosystem kenkyu kaihatsu (Chofu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development efforts are exerted to realize (1) a variable function residential circumstance system for the aged people and (2) a medical welfare and life assisting information system for helping the aged or handicapped people lead an independent life. Under item (1), a variable function residential circumstance system under which functions of the residence may be changed dependent upon inhabitants' degree of debility will be developed, and an information system will be developed under which medical welfare assistance and life assistance are integrated. Under item (2), residences, welfare appliances, and nurse/attendant assisting systems will be assessed and examined. In fiscal 2000, under item (1), a variable function residential unit was fabricated and was inhabited experimentally by people approximately 1 to 4 in the degree of need for nursing care, and problems were isolated to be discussed toward putting the system to practical use. Under item (2), physical power required for nursing and attending was measured using medical assistance appliances for in-home nursing care installed at Welfare Technohouse Chofu, and ergonomic studies were conducted with a view to relieving the load to be imposed upon those engaged in the nursing and attending work. (NEDO)

  9. Marketing research on potential demands of photovoltaic systems. Taiyoko hatsuden system no senzai shijo chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    1988-03-01

    Applicable uses and the market size for photovoltaic (PV) systems were investigated taking into consideration the features and economics of such systems. As a result of computing representative usage examples together with the extent of potential demand for PV, 238 GW for the power source in private homes, 76 GW for green houses, 126 GW for sewage water treatment plants, 4 GW for schools and universities and others were estimated. For the greater number of PV systems already in actual use, non-cost factors acted as major determining factors when deciding on implementation. Promising uses (applicable ideas) seen from the standpoint of non-cost factors were studied in order to develop the PV system market and gain breakthrough for lowering future costs and increasing proliferation for such systems. When it comes to simultaneously decreasing costs and increasing demand for solar batteries in the coming days, it will be impossible to make an immediate transition from the present state of demand for public use and for special use to the final goal of demand as a power source in the home. There is a need for an intermediate demand that can bridge this gap. (13 figs, 9 tabs)

  10. Fiscal 1993 survey report. Coal hydrogasification technology development; 1993 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. The hydrogasification process that Japan should develop is a flexible process that operates on the three modes of the maximum SNG yield, the maximum heat efficiency, and the maximum BTX (benzene, toluene, xylene) yield. Such being the case, an ARCH (advanced rapid coal hydrogasification) process was proposed, provided with a reactor capable of an ARCH-1 type operation for the maximum gas cooling efficiency and an ARCH-2 type operation for the maximum liquid yield. As for the details of the ARCH process development, the time and priority for development were determined for each of the items in consideration of the technical contents and the steps of development in the flow from a bench plant to a demonstration plant. The technology of char cooling and extraction was specified as the first item to be immediately dealt with. As for the development of the hydrogasification reactor, it was concluded that it was suitable to begin with the development of an injector. According to the development plan, the cost required up to a pilot plant test was estimated at 2 billion yen. (NEDO)

  11. Report on the bituminous coal liquefaction sub-committee in fiscal 1992; 1992 nendo rekiseitan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the bituminous coal liquefaction sub-committee in the Sunshine Project in fiscal 1992. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant was launched in fiscal 1991. It is necessary to execute the pilot plant plan steadily in the future, and at the same time, reliably acquire different data by means of supportive researches. Economic performance of the process is also important. The first sub-committee meeting presented the following agenda: the status of constructing the 150-t/d pilot plant, tests and investigations thereon, research works by using a 1-t/d PSU, development of the most suitable coal refining technology, development of a coal pretreatment technology, improvement of the distilled oil distribution, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. The second sub-committee meeting presented the following agenda: the status of constructing the pilot plant, tests and investigations on improving the performance of natural pylite catalyst and circulating solvent, technological investigations on structuring a liquefying reaction data analyzing system, studies using a 1-t/d PSU, development of the most suitable coal refining technology, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. (NEDO)

  12. Fiscal 1992 survey report. Coal hydrogasification technology development; 1992 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. In the study of coal hydrogasification, a mathematical simulation was implemented to estimate the distribution of products with the pyrolytic reaction and the hydrogenolytic reaction controlled independently in the ARCH-2 (advanced rapid coal hydrogasification-2) process, the said two reactions representing the key concepts of the ARCH-2 process. It was then disclosed that a two-stage reaction control would increase the liquid yield. Also, a tentative calculation was made of gas cooling efficiency and cost performance in a process capable of achieving the target liquid acquisition rate. It was then found that BTX (benzene, toluene, xylene) production up to approximately 15% in terms of carbon was feasible and that the SNG price would be 29.03 yen/Nm{sup 3} with benzene priced at 90 yen/kg, these promising a better result than in the ARCH-1 process. The gas cooling efficiency of the ARCH-2 process was but 72.0% or less, however, which demanded improvement. Studies were made, based on the results of studies in progress since fiscal 1990, about what the hydrogasification process for Japan to develop should be. (NEDO)

  13. FY 2001 Report of regional new energy vision for Futaba Town; 2001 nendo Futaba machi chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for enhancing people's consciousness of such at Futaba Town, Fukushima Prefecture, surveys and studies were conducted involving the amount of energy consumed by the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The annual energy consumption of the town is 113,049 times 10{sup 6} kcal, with automobiles consuming 47.2%, manufacturing industries 19.8%, households 18.9%, and commerce 12.6%. The amount of carbon dioxide due to the consumption is estimated at 9,999 times 10{sup 3} kg-C in total. Studies were made about new energy introduction projects toward 2010, which involved the introduction of photovoltaic power generation systems and solar heat utilization systems into four public facilities and 214 general residences; introduction of nine clean energy vehicles into public facilities and 181 into general residences; a wind power station near the seashore; a mini-scale hydroelectric power system for irrigation; introduction of new energy for illuminating sightseeing roads and parks, and so forth. (NEDO)

  14. Report on establishing new energy vision at Furen Town area; 2001 nendo Furen cho chiiki shin energy vision sakutei hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    With an object of accelerating introduction of and uplifting consciousness on new energies at the city of Furen in Hokkaido, investigations and discussions were given on the energy demand, quantity of new energies in existence, and new energy introduction projects of the city, thus a new energy vision was established. The estimated amount of energy consumed in Furen Town is 119,846 x 10{sup 3} kWh. By departments, the transportation department has the highest consumption ratio, followed by general household. Energy types are kerosene, followed by heavy oil, electric power and LPG in the decreasing order. The important new energy introduction projects have discussed the ''Snow Storehouse Workshop'' being a low temperature rice storage facility in Bibai City, which performs cold storage and shipment adjustment of agricultural products, through-the-year agriculture to perform house cultivation by using rice straws and rice husks as the heat energy source, adjustment of temperatures of paddy fields by using calorific power of rice husks, electric power generation and heat supply by using heat of combustion of chips from lumber factories, electric power generation and heat supply by using livestock excreta (bio-gas), and introduction of new energies into schools and parks. (NEDO)

  15. Fiscal 1998 achievement report on welfare technosystem research and development. Kyoto; 1998 nendo walfare technosystem kenkyu kaihatsu (Kyoto) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To be ready for the computing-everywhere age to come, it is necessary to create environments in which the barrier-free utilization is ensured of various apparatuses of the daily routine, such as various bodily function substituting apparatuses capable of compensating for the degraded functions of disabled or aged individuals. Under the circumstances, a system for building man-machine interfaces in the home or the like is required, and fundamental technologies of architecture and information infrastructure have to be established on which the development of technologies for the field involved will proceed. Concerning the technologies already in existence in this field of research, a survey is conducted of the status of research and development of information interface techniques primarily at Stanford University, and a report is made thereon. Also reported is the information obtained at Technology and Persons with Disabilities Conference 1999. The result of a survey of the trend of research and development of the smart house under the TIDE (Technology Initiative for Disabled and Elderly People) project and the result of a survey of an information standardization project for equipment control in Europe are reported, and the result of a survey of the approach of Kyoto's welfare apparatus distributors to the development of equipment is made known. (NEDO)

  16. Report on a comprehensive research study (home welfare apparatus system - interface); Sogo chosa kenkyu (zaitaku fukushi kiki system - interface) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In the light of the increasing role of welfare at home with the advance of the aging society, the paper conducted an investigational study on the R and D of the home welfare apparatus system - interface. In the study, making the most of the leading home care apparatus systems (welfare technohouses) installed at seven places in the country, the paper carried out a stay experiment on how the life is in the welfare house into which home welfare apparatus is integrated, and an experiment to assess biological data on aged people. Especially as to the support apparatus used for smooth life motions in houses such as movement, excretion and bathing, examined were the linkage with house bodies, care apparatus used, mutual interface with welfare apparatus, etc. By the experiments to assess these home welfare apparatus, an analytical study was conducted on the points to be improved in welfare apparatus and housing equipment, and at the same time on the course of the research/development. Concerning a system for the research study, a research promotion committee was established in Technology Research Association of Medical and Welfare Apparatus, the members of which are learned persons from the industrial circle, the government and universities. 111 figs., 36 tabs.

  17. Achievement report for fiscal 1998. Multimedia system for the disabled; 1998 nendo seika hokokusho. Shogaisha taio multimedia system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Development has been made on the element technologies for a multimedia system for the disabled. In developing the non-visual graphical user interface (GUI) access system, a non-visual access system to enable the visually disabled to access a GUI system by utilizing sound and tactile devices was developed. In developing the three-dimensional sound utilizing information providing system, a system was developed, in which information on screen arrangement of the GUI in a personal computer is presented as spatial sound positions by using the three-dimensional sound control technology. The system can be operated non-visually using a mouse by controlling movements of a cursor. The current fiscal year has improved three-dimensional sound producing devices, three-dimensional sound interface, and how to handle their applications. User evaluations were also performed. Functions were expanded and improved in a system and an optical media reader that enable the visually disabled person to read printed papers by himself. Development was made also on a function to link the system with a total system. (NEDO)

  18. Investigation report on establishment of new energy vision in Toyohashi area; Toyohashi chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    The 'new energy vision for Toyohashi (Aichi Prefecture) area' was established from the viewpoint that proliferation of new energy use, which is less familiar and higher in cost, requires induction by urban and environmental measures, and consistency with district characteristics. The achievements were put into order as the report on the Toyohashi area new energy vision and the investigation on the vision establishment. The vision is composed by the following four items: 1) basic matters concerning the vision, 2) ideas and policies of the vision, 3) major measures for introducing new energies, and 4) promotion of the vision. Item 3) presents the introduction measures, introduction project, and measure development by areas. Considerations on the introduction measures include enlightenment for proliferation, expansion in information provision, development of preferential treatments, initiative introduction into public facilities, and the measures to strengthen cooperative works by citizens, business entities, and the administration. The following four projects were set: introduction of wastes power generation into the Resource Production Center (wastes treatment plant), improvement of the surplus heat utilization facilities, and introduction of wind power generation into the General Agricultural Park. (NEDO)

  19. 17th Symposium of NEDO projects. Industrial technology subcommittee; Sangyo gijutsu bunkakai. Dai 17 kai jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    Described herein are the reports presented to the industrial technology subcommittee, 17th symposium of NEDO projects. For development of high-efficiency industrial furnaces by high-temperature air combustion (including regenerative combustion), high-temperature air above 1000 degrees C is used, where carbon dioxide and NOX are possibly abated by 30% or more and 50%, respectively. The worldwide development is also described. For production of high-function ceramic materials at low temperature, the soft solution process is proposed for the in-situ production of these ceramic materials from the aqueous solution without using high temperature or high energy. For example, the high-functional ceramic material can be produced in-situ on a substrate by reacting the highly active aqueous solution with the substrate by a combination of, e.g., the hydrothermal and electrochemical reactions, without needing post-treatment under heating. For the marine biological technologies, deposition of living organisms is described. A geodome is developed for utilizing very deep (50m or deeper) underground spaces. It is a dome-shaped space supported by no strut, having dimensions of 50m in diameter and 30m high not to affect the surrounding environments, e.g., underground water. The techniques for creating advanced functional materials are developed by combining, e.g., laser, plasma, ion and magnetic field in diversified manners. (NEDO)

  20. Fiscal 1999 technical survey report. Cooperative project on energy conservation seminar; 1999 nendo sho energy seminar kyoryoku jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    NEDO (New Energy and Industrial Technology Development Organization), from the viewpoint that the development and popularization of energy conservation technologies are extremely important as energy conservation measures, collected energy related primary information from 12 Asian countries including Japan for the development and popularization of energy conservation technologies, and has constructed a database NEDO/DB. NEDO is now propelling forward its efforts to popularize the database. For popularizing NEDO/DB in Vietnam and for rendering the people conscious of energy conservation, NEDO dispatched some lecturers to an energy conservation seminar sponsored by the Vietnamese Government. The importance of energy conservation promoting measures was highlighted at the seminar. NEDO's approach to AIJ (activities implemented jointly) and CDM (clean development mechanism) was described at the seminar, and a lecture meeting was held to explain NEDO/DB and to teach how to use the database. (NEDO)

  1. Fiscal 1999 achievement report. Research and development of synergy ceramics; 1999 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Studies are conducted on three subjects, which are the development of 1) high-temperature energy materials technology, 2) ultrasophisticated materials technology, and 3) high-performance active materials technology. Under subject 1), high-strength porous materials are to be developed, which are resistant to heat and corrosion, tolerant of damage and deformation, and light in weight. In addition, relative to fluid transmission, materials are to be developed, which are highly resistant to heat, corrosion, and thermal impact, and capable of separating and removing particulates of powder dust. Under subject 2), efforts are under way to develop two technologies, related to materials creation and their application. The former technology involves the development of a process of simultaneously equipping materials with high wear resistance, desired friction factors, and desired mechanical and thermal characteristics; a process of equipping them with a trace damage detecting function; and a process of simultaneously equipping them with functions of restoration from accidents and of self-lubrication. Relative to the latter technology, efforts are conducted, in coordination with the endeavors for the above-said materials creation technology, to develop materials and their application with attention paid to some specified functions. Under subject 3), self-complete type ceramic materials not requiring an external driving power source are to be developed, in which a selective cleaning function and environmental energy conversion function are amalgamated. (NEDO)

  2. Achievement report for fiscal 1998. Esophageal vocalization aid system; 1998 nendo seika hokokusho. Shokudo hassei hojo sochi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Development has been made on element technologies for an esophageal vocalization aid system. With regard to the speaker, selection and trial production were performed on a speaker used for a phono-coupler to be used in coupling with a telephone transmitter. Performance not differing from that in the currently used telephone set was obtained in the overall characteristics evaluation using a dummy telephone circuitry. For the microphone, two kinds of hands-free microphones were fabricated on a trial basis. In order to develop pitch extraction and amplitude pitch conversion systems, pitch extraction performances were compared and discussed on the following five methods: the auto-correlation method, the Cepstram method, the average magnitude difference function (AMDF) method, the simplified inverse filter tracking (SIFT) method, and the time-domain excitation extractor using minimum perturbation operator (TEMPO) method. The hauling phenomenon, having come up as a problem in an auxiliary digital device, was analyzed to discuss methods for prevention thereof. In developing a voice/unvoiced distinction judgment method, a method using low domain power and high domain power was discussed. Development has been made on exclusive ICs, a voice analyzer, and the using feeling enhancing technology. In developing a total system, a digital unit incorporated esophageal vocalization aid system was developed and improved. (NEDO)

  3. Investigation report on establishment of new energy vision in Toyohashi area; Toyohashi chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    The 'new energy vision for Toyohashi (Aichi Prefecture) area' was established from the viewpoint that proliferation of new energy use, which is less familiar and higher in cost, requires induction by urban and environmental measures, and consistency with district characteristics. The achievements were put into order as the report on the Toyohashi area new energy vision and the investigation on the vision establishment. The vision is composed by the following four items: 1) basic matters concerning the vision, 2) ideas and policies of the vision, 3) major measures for introducing new energies, and 4) promotion of the vision. Item 3) presents the introduction measures, introduction project, and measure development by areas. Considerations on the introduction measures include enlightenment for proliferation, expansion in information provision, development of preferential treatments, initiative introduction into public facilities, and the measures to strengthen cooperative works by citizens, business entities, and the administration. The following four projects were set: introduction of wastes power generation into the Resource Production Center (wastes treatment plant), improvement of the surplus heat utilization facilities, and introduction of wind power generation into the General Agricultural Park. (NEDO)

  4. Fiscal 2000 report on regional new energy vision for Tanoura town; 2000 nendo Tauracho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A new energy vision has been formulated to make an environmentally friendly community of Tanoura town, Kumamoto Prefecture, which is a 6,000-people town facing Shiranui Bay and consisting of seashore, the streets, and a mountainous district. The amount of new energy in existence, when converted into electric power, will be 10 GWh/year accounting for approximately 20% of 1999 power consumption. The types of new energy subjected to study are solar energy, wind energy, biomass energy, refuse-derived energy, and geothermal energy, with solar energy surpassing the rest. In the new energy vision, the roles of the administration, citizens, and industrialists are made obvious; new energy introduction projects are established for the introduction of photovoltaic power, solar heat, and wind power into Hot Spring Center; and clean energy vehicles will be acquired to serve as official vehicles. The new energy vision booklet comprises six chapters, with chapter 1 dealing with the basic philosophy of vision formulation. (NEDO)

  5. Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-10-01

    Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

  6. Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1981 reported. This year, technological reexamination was conducted for a 2,000 MWt commercial MHD generation plant, with evaluation carried out on the cost performance including the construction and operation cost. In addition, for the purpose of intermediate R and D towards the practicability, examination was also conducted on a system structure, concrete specifications of component element, cost of R and D including operation expenses for example, concerning an 100 MWt class experimental plant and a 500 MWt class plant. In the investigation of the overseas trend, information was summarized in detail on the experimental devices, combustors, generation channels, electrode materials, electrode phenomena, theoretical analyses, seeds, slag, component equipment, instrumental technologies, conceptual designs of generation plant, commercial plant, etc., in Soviet Union, China, Holland, India and EPRI, on the basis of the materials from the 19th MHD symposium held in UTSI and from the coal MHD specialist conference held in Sydney. (NEDO)

  7. Summary of reports on 1979 result of Sunshine Project. Solar energy; 1979 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-04-01

    This report is a compilation of all outlines of the results concerning 'solar energy' for which R and D was carried out as a part of Sunshine Project in fiscal 1979. The research subjects (items of the studies) are written below. 1. Solar energy system (measurement of spectral irradiance, utilization system, and meteorological investigation); 2. Solar thermal power generation system; 3. Photovoltaic power generation system (basic research on solar cells, silicon vertical ribbon crystal, silicon horizontal ribbon crystal, particle non-acceleration growth type thin film silicon crystal, particle acceleration growth type thin film silicon crystal, new type solar cells, secondary to quaternary compound semiconductor solar cells, and photovoltaic power generation system); 4. Solar cooling, heating and hot water supply system (evaluation system, newly-built private residential system, existing private residential system, multiple dwelling system, large building system, synthetic resin materials, glass based materials, and metallic materials); 5. Solar energy new utilization method (new power generation system and materials); 6. R and D on solar thermal power generation plant (R and D on pilot plant, experimental research for developing plant on curved surface converging method, and experimental research for developing plant on tower converging method). (NEDO)

  8. Summary of the FY 1988 Sunshine Project results. Hydrogen energy; 1988 nendo sunshine keikaku seika hokokusho gaiyoshu. Suiso energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-04-01

    Outlined herein are the results of researches on hydrogen energy as part of the FY 1988 Sunshine Project results. Researches on the techniques for producing hydrogen by electrolysis of water using a polymer electrolyte include development of power-supplying materials for electrolysis at high current density, and basic studies on the electrolysis using an OH ion conducting type polymer electrolyte. Researches on the techniques for producing hydrogen by electrolysis with hot steam include development of the materials, techniques for processing these materials, and electrolysis performance tests. Researches on the techniques for transporting hydrogen by metal hydrides include development of hydrogen-occluding alloys of high bulk density, and techniques for evaluating characteristics of metal hydrides. Researches on the techniques for storing hydrogen include those on alloy molding/processing techniques, hydrogen-storing metallic materials, and new hydrogen-storing materials. Researches on the techniques for utilizing hydrogen include those on energy conversion techniques using hydrogen-occluding alloys, and hydrogen-fueled motors. Researches on the techniques for safety-related measures include those on prevention of embrittlement of the system materials by hydrogen. (NEDO)

  9. Summary of the FY 1989 Sunshine Project results. Hydrogen energy; 1989 nendo sunshine keikaku seika hokokusho gaiyoshu. Suiso energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-04-01

    Outlined herein are the results of researches on hydrogen energy as part of the FY 1989 Sunshine Project results. Researches on the techniques for producing hydrogen by electrolysis of water using a polymer electrolyte include those on the SPE electrolysis at high temperature and current density, and basic studies on the electrolysis using an OH ion conducting type polymer electrolyte. Researches on the techniques for producing hydrogen by electrolysis with hot steam include development of the materials, techniques for processing these materials, and electrolysis performance tests. Researches on the techniques for transporting hydrogen by metal hydrides include development of hydrogen-occluding alloys of high bulk density, and techniques for evaluating characteristics of metal hydrides. Researches on the techniques for storing hydrogen include those on hydrogen-storing metallic materials, alloy molding/processing techniques, and new hydrogen-storing materials. Researches on the techniques for utilizing hydrogen include those on energy conversion techniques using hydrogen-occluding alloys, and hydrogen-fueled motors. Researches on the techniques for safety-related measures include those on prevention of embrittlement of the system materials by hydrogen. (NEDO)

  10. Report of high efficiency waste power generation technology development in 1995; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (1995 nendo hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    High temperature and high pressure steam has been investigated for the high efficiency waste power generation technology development. The steam temperature below 300 centigrade is currently employed to avoid the corrosion of superheater, and the generating efficiency is less than 15%. Practical application of 500 centigrade and 100 kg/cm{sup 2} is planned by developing corrosion resistance materials. Environmental load reduction technology has been also developed. For the external circulation type fluidized bed furnace combustion tests using dummy waste in fiscal 1995, the temperature control at bag filter was effective for suppressing the dioxins. When using waste plastics, HCl could be reduced by blowing Ca compounds. Various Cr-Ni-Mo-based alloys have been developed as a corrosion resistance superheater tube material, and are currently tested. For the environmental load reduction technology, the development of pulse plasma exhaust gas treatment method has been continued from fiscal 1993. In fiscal 1995, this method was confirmed using a small-scale test unit, and also tested using a 5000 Nm{sup 3}/h bench-scale unit. The removal rates of dioxins at the outlet of bag filter were 99.8% and 99.3%, respectively. They were found to be affected greatly by the pulse waveform. 13 refs., 107 figs., 24 tabs.

  11. Report on survey in fiscal 1999. Comprehensive survey on medical appliances; 1999 nendo iryo kiki sogo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The environment around medical treatment in Japan is changing greatly in recent years, because of aging of the population, increase in life habit diseases, and progress in medical science and technologies. In addition, the needs of people are on the trend of diversification. Furthermore, as a result of the information communication field gaining remarkable power, people can obtain information in various forms, and are acquiring chances of learning various kinds of knowledge about medical treatment. Thus, scenes to respond to demands of patients are increasing more than ever in medical activities. On the other hand, works and conversion in providing efficient medical services are sought because of pressures on medical finance. Therefore, the 'medical and welfare device development project' was launched in fiscal 1994, wherein NEDO has been promoting the research and development jointly with private business entities. In fiscal 1999, assignments in important technologies will be made clear taking the future into the sight on three themes in two fields of developing low invasive operation systems, and comprehensively developing artificial organ technologies. Themes to be developed newly in the future will be selected, and the contents of the research and development thereon and the ways it should be will be investigated, evaluated and discussed specifically. (NEDO)

  12. Report for fiscal 1994 by subcommittee on coal liquefaction basic technology; 1994 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This report covers the proceedings of subcommittee meetings. Using PDUs (process development unit), comparison is made between bituminous coal-derived oils (150t/d plant for the Indonesian coal) and brown coal-derived oils (50t/d plant for the Yallourn coal), product quality is improved by a 2-stage refining process, engines are tested, etc., all these demonstration and research efforts intended to win social recognition for coal liquefaction products. Among basic studies, there are the development of technologies for reforming coal-derived oils and for mixing them will petroleum, development of new catalysts for reforming, development of a technology for separating heterocompounds and the like, and the development of their applications. Furthermore, technologies are developed for environmentally friendly coal liquefaction, feasibility of coal liquefaction technology internationalization is deliberated, and technical researches and joint researches are conducted. At the second meeting of the subcommittee, achievements relative to the refining and applications of liquefaction products are presented, including the hydrorefining of naphtha, heating oil, and light oil; development of new catalysts; heterocompound separation technology; and the development of new applications. In relation with the development of environmentally friendly coal liquefaction technologies, studies are presented on liquefaction conditions and on the upgrading of basic technologies of liquefaction. Also referred to are the reports delivered at a meeting on liquefaction catalysts (January 1995). (NEDO)

  13. Report on the bituminous coal liquefaction sub-committee in fiscal 1993; 1993 nendo rekiseitan ekika bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This paper reports the activities of the bituminous coal liquefaction sub-committee in fiscal 1993. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant, launched in fiscal 1991, will be performed under the operation research plan for efficient operation, based on the result of discussing the total project cost in fiscal 1992. The status of constructing the 150-t/d pilot plant in fiscal 1993 is in the phase of making the foundations subsequently from fiscal 1992, procurement of devices and construction materials, constructions of iron structures, installation, heat insulation, and painting, and building the central control building and piping facilities outside the battery limit. The paper also reports the tests and investigations on improving performance of natural pylite catalyst, the tests and investigations on improving performance of circulating solvent, and the technological investigations on structuring a liquefying reaction data analyzing system. For the supportive researches on the pilot plant, the paper describes studies by using a 1-t/d PSU, studies on coal liquefaction conditions, studies on synthesized iron sulfide catalysts, and studies on solvent hydrogenating catalysts. A comprehensive discussion was also given. (NEDO)

  14. Fiscal 1993 investigational report on heat pump heat storage technology; 1993 nendo heat pump chikunetsu gijutsu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is for an investigation into the heat pump (HP) use heat storage technology, with the aim of clarifying the present status of HP heat storage technology, the utilization status, and the developmental trend of technology and of contributing to the spread of heat energy effective use using HP heat storage technology and to the promotion of the technical development. Accordingly, the evaluation of the following was made: sensible heat (SH), latent heat (LH), chemical heat storage technology (CH), and heat storage technology (HS). Investigations were made on the sensible heat use heat storage technology of water, brine, stone, soil, etc. in terms of SH; the phase change sensible heat use heat storage technology of ice, hydrate salt, paraffins, etc. in terms of LH; hydration, hydroxide, 2-propanol pyrolysis, adsorption of silica gel, zeolite and water, and heat storage technology using metal hydride, etc. in terms of CH. In terms of HS, the following were studied and evaluated from the study results of the heat storage system in which HP is applied to the sensible heat and latent heat type heat storage technology: contribution to the power load levelling and the reduction of heat source capacity, heat recovery and the use of unused energy, improvement of the system efficiency by combining HP and heat storage technology. 24 refs., 242 figs., 56 tabs.

  15. Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

  16. Fiscal 1998 achievement report on welfare technosystem research and development. Tokushima; 1998 nendo walfare technosystem kenkyu kaihatsu (Tokushima) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project aims to construct a real-time system capable of searching a wider living area through establishing a management system centralized by remote control by improving on radio transmitters in a communication network and on a central station communication control system centering about a health and welfare office, for alleviating the burden of the nursing of old persons who wander, for preventing them from accidents attributable to wandering, and for finding and protecting them in time. For the construction of such a system, surveys and studies are conducted for the preparation of fundamental designs for personal data files on individuals carrying radio transmitters, monitor screen manipulation, program for acquiring information from a transmitter about its current position and for receiving information from the terminal station, and a frequency selecting program or the like to give instructions to the terminal station to probe the frequency on which the missing person's transmitter operates. In this fiscal year, specifications are studied of software programs based on data obtained from an experiment conducted for the practical application of a search network system utilizing the currently available radio direction finding technique, which effort is exerted mainly at the infirmary of Hanoura-cho, Tokushima Prefecture. (NEDO)

  17. FY 1986 report on the committee of the Coal Gasification Committee; 1986 nendo sekitan gaska iinkai hon'iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    The paper reported on activities of the committee of the Coal Gasification Committee in FY 1986. In the 1st Committee Meeting, after selecting the chairperson, report/discussion were made about the outline of the FY 1986 coal gasification technology development plan. The distributed data were the outline of the development of an entrained bed coal gasification power plant, outline of the development of a 40t/d fluidized bed coal gasification plant, outline of the design of a 1,000t/d 100,000KW-class demonstrative plant, outline of the development of coal utilization hydrogen production technology, and outline of the development of high-calorie gas production technology. In the 2nd Committee Meeting, report/discussion were made about activities of each section of the committee and the state of progress of the development of coal gasification technology. The distributed data were those on the development of an entrained bed coal gasification power plant, development of a 40t/d fluidized bed coal gasification plant, design of a 1,000t/d 100,000KW-class demonstrative plant, and development of coal utilization hydrogen production technology (design/construction of pilot plant, study using small equipment). (NEDO)

  18. Fiscal 1999 research report. Simulation analysis on petroleum substituting energy; 1999 nendo sekiyu daitai energy keiryo bunseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on simulation analysis on petroleum substituting energy. The simulation model for analyzing social and energy supply and demand structures comprehensively was established by improving the China and Korea models developed in fiscal 1998 through a use of input-output tables. In simulation of the China model, the reference case showed that a primary energy demand in 2030 reaches 3.3 times as much as that in 1997 (2.9 times in CO{sub 2}), resulting in serious energy and environment problems. Reduction of primary energy and CO{sub 2} is possible by promotion of energy saving and introduction of a carbon tax. In simulation of the Korea model, the reference case showed that CO{sub 2} emission in 2030 reaches 2.2 times as much as that in 1997, showing an annual increase rate of 2.4%. The annual increase rate can be reduced by introducing a carbon tax. The simulation model for automobile energy was also established for major countries in Asia. Automobile energy consumption increases with diffusion of automobiles until 2030 gradually. In particular, the consumption in China reaches that in Japan in 2010. (NEDO)

  19. Basic research report on introduction of new energy into Yamaguchi Prefecture; Yamaguchiken shin energy donyu kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In Estimation Work 1, the potentially available amount (the amount in existence) is determined for each type of new energy by use of various new energy related technologies now available. In Estimation Work 2, the available amount is determined for each type of new energy, with social restraint and installation space taken into consideration. Effects upon energy saving and CO2 emission reduction are 4405.2% and 3439.1% in Estimation Work 1, and 6.5% and 8.0% in Estimation Work 2. A conclusion is reached after examining the outcomes of the said estimation works and the results of simulations (conducted on the assumption of new energy introduction in fiscal 2010), the number of advocates expressing their support of new energy adoption in questionnaires answered by various businesses and offices in the prefecture, high possibilities of introduction detected in a survey of exploitation projects of cities, towns, associations, and unions, and the prospect of acceptance by households. The conclusion is that the types of new energy and technologies to be selectively introduced into the prefecture will be photovoltaic power generation, wind power generation, clean energy vehicles, energy extracted from wastes, cogeneration, fuel cells, passive solar system, utilization of waste heat from factories and mills, and ocean energy. These are abundant in terms of potentially available amount and of available amount. (NEDO)

  20. Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

  1. Fiscal 2000 coal engineer training project. Report on senior course; 2000 nendo sekitan gijutsusha yosei jigyo jokyu course hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The above-named course consisted of three weeks of lectures and three months of visits to coal mines and harbor facilities and tours to coal consumers such as power stations and steel manufacturing plants. The report has turned out to be an introductory manual on coal mining consisting of coal mining technologies such as coal resource exploration, coal mining, and coal preparation, and the state of Australian coal industry. The manual comprises (1) job training in Japan (attendance at lectures), (2) inspection and training in Japan (coal consumers), (3) intensified lectures at University of New South Wales (coal mining and preparation), (4) current state of Austrian coal industry, (5) inspection tours to Australian coal mines, (6) inspection tours to Australian harbor facilities, and (7) the state of Australian coal mine management. Fifteen intensified lectures were given, including the 'Overview of Australian coal industry' and 'Coal handling and transport.' Nine coal mines were visited in Queensland, and 21 in New South Wales. As for the state of Australian coal mine management, there is a trend toward contract mining but self-mining constitutes the mainstream. (NEDO)

  2. Fiscal 2000 achievement report. Welfare technosystem research and development (Kamogawa); 2000 nendo welfare technosystem kenkyu kaihatsu (Kamogawa) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of assisting in-home medical care, a system to enable in-home acquisition, compression, accumulation, distribution, and regeneration of auscultatory sounds (cardiac sound, respiratory sound) is added to telemedicine assisting system technologies for remotely located doctors' decisions and instructions for in-home medical care. In fiscal 2000, for improvement on the already-developed system, operationality was improved, uptake was realized of still images (digital camera pictures) mainly for diseases in dematology where such is strongly demanded, and a transmitter function was augmented. The system enables the PHS (personal handyphone system) aided exchange of medical data between portable terminals on patrol and (doctors') personal computers through the personal computer server in the hospital. Doctors are able to administer remote telemedicine now that biomimetic information on remotely located patients such as still medical images and auscultatory sounds necessary for diagnosing is available in the hospital. (NEDO)

  3. Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

  4. Fiscal 1993 report on the separation/refining technology section meeting; 1993 nendo bunri seisei gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Group activities in fiscal 1993 are reported. In the study of hydrogenation refining of the naphtha fraction under the project for 'the upgrading of coal oil and the development of oil blending technology,' a hydrogenation experiment is conducted for deheterocyclicity for in the naphtha fraction (90-180 degrees C). The neutralization process is found to greatly accelerate denitrification, multiplying the rate constant 2-5 times at 300 degrees C. In the research and development of application technologies, the ASTM-D4625-86 method is applied to the storage test of crude oils such as naphtha from liquefied Yallourn coal, kerosene, and light oil, and the results are compared with those from natural storage. It is then found that this acceleration test is applicable even to oils from coal liquefaction. In the research and development of novel catalysts, it is found, relative to the 1st-stage hydrogenation catalyst, that an increase in the amount of supported tungsten enhances the activity and life of the catalyst and, relative to the 2nd-stage hydrocracking catalyst, that YD zeolite is effective in prolonging the life of the catalyst. (NEDO)

  5. FY 1998 survey report. Petroleum substituting energy metering analysis survey; 1998 nendo chosa hokokusho. Sekiyu daitai energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In this survey, metering models in the Asian/Pacific region where energy demand is rapidly increasing were constructed which are used for the comprehensive analysis of the relations between changes in social structure such as economic growth, change in industrial structure, and progress in energy conservation technology and new energy technology, and the energy supply/demand structure. The survey was carried out aiming at contributing to the international development of Japan's energy policy in future by quantitatively analyzing/evaluating influences of various energy policies/economic policies on the economy and energy supply/demand, through various kinds of simulation models. In FY 1998, information collection for modeling was made in China and Korea out of the Asian/Pacific region. At the same time, pilot models were constructed, and simulation was made for the standard case. Moreover, an analysis was conducted of the relation between economic growth and motorization in each country of the world as the basic data preparation on energy consumption in the transportation sector. (NEDO)

  6. Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

  7. Fiscal 2000 report on advanced parallelized compiler technology. Outlines; 2000 nendo advanced heiretsuka compiler gijutsu hokokusho (Gaiyo hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was carried out concerning the automatic parallelized compiler technology which improves on the practical performance, cost/performance ratio, and ease of operation of the multiprocessor system now used for constructing supercomputers and expected to provide a fundamental architecture for microprocessors for the 21st century. Efforts were made to develop an automatic multigrain parallelization technology for extracting multigrain as parallelized from a program and for making full use of the same and a parallelizing tuning technology for accelerating parallelization by feeding back to the compiler the dynamic information and user knowledge to be acquired during execution. Moreover, a benchmark program was selected and studies were made to set execution rules and evaluation indexes for the establishment of technologies for subjectively evaluating the performance of parallelizing compilers for the existing commercial parallel processing computers, which was achieved through the implementation and evaluation of the 'Advanced parallelizing compiler technology research and development project.' (NEDO)

  8. Fiscal 1991 survey report. Coal hydrogasification technology development; 1991 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. Dealt with in the survey of basic studies on hydrogasification were the effect of gasification conditions, mechanism of tar decomposition, model-using estimation and assessment of reaction heat, and so forth. In an effort to develop a reactor, the current status was studied and future tasks were extracted concerning the one-through type and the internal circulation type entrained bed hydrogasification furnaces. In the study of practical application of the coal hydrogasification process, it was found that gas cooling efficiency would be increased from last fiscal year's 75.2% to approximately 78% by optimizing the process configuration. An ARCH (advanced rapid coal hydrogasification) process to have a novel reactor was proposed, and, for its commercialization, guidelines for dimensionally enlarging the process were worked out and tasks to discharge at each of the development stages were extracted. Relative to pilot tests, an efficient development program was deliberated, in particular, which comprised ARCH-1 and ARCH-2. (NEDO)

  9. Fiscal 1994 survey report. Coal hydrogasification technology development; 1994 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. For the development of an ARCH (advanced rapid coal hydrogasification) process, a plan was prepared covering the basic concept of the process, overall development program, hydrogen/oxygen burner, and an injector. The overall development program comprises element studies (4 years) and the study of the operation of a 50 tons/day pilot plant (8 years), and deals with the development of a reactor and peripheral equipment. Next comes a total system verification effort using a 200 tons/day verification plant in combination with a hydrogen production process, and this aims to achieve commercialization at 3 million Nm{sup 3}/day. As for the hydrogen/oxygen burner, a structure was proposed after surveys of literature and patents on burner structures, ignition methods, and monitoring methods. In the development of an injector, a plan was prepared for testing, and improving, the performance in a cold/hot model of a specimen incorporating the proposed hydrogen/oxygen burner. Basic studies to be carried out include simulation-aided performance prediction. (NEDO)

  10. Report on the actual situations of the commercially applied, industrial robots; Sangyoyo robot ni kansuru kigyo jittai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-08-01

    Described herein are the actual situations of industrial robots as the FY 1991 questionnaire survey results. The questionnaires were sent to 541 factories, and 74% thereof were recovered. The major machine types fall into categories of manual manipulator, stationary sequence manipulator, remote controlling robot, sequence robot, playback robot, numerically controlling robot and intelligent robot. They are mainly driven by hydraulic, pneumatic, or electrical power. Their mechanism types cover polar coordinate, cylindrical coordinate, rectangular coordinate and articulation types, among others. They are mainly controlled by electronically, electrically (hydraulic or relay), or pneumatically. The major purposes for general works include casting, forging, resin processing, heat treatment, pressing, welding, coating, machining, cutting, assembling, reception/delivery of goods, and testing/inspection. The special works they are in service include those for power/gas/water services, construction works, and research and development. By work step, they are in service, e.g., for loading/unloading goods, palletising/packing goods, supporting, screening, welding, spraying/coating, grinding, clamping, assembling, and riveting. (NEDO)

  11. FY 1998 survey report. Petroleum substituting energy metering analysis survey; 1998 nendo chosa hokokusho. Sekiyu daitai energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In this survey, metering models in the Asian/Pacific region where energy demand is rapidly increasing were constructed which are used for the comprehensive analysis of the relations between changes in social structure such as economic growth, change in industrial structure, and progress in energy conservation technology and new energy technology, and the energy supply/demand structure. The survey was carried out aiming at contributing to the international development of Japan's energy policy in future by quantitatively analyzing/evaluating influences of various energy policies/economic policies on the economy and energy supply/demand, through various kinds of simulation models. In FY 1998, information collection for modeling was made in China and Korea out of the Asian/Pacific region. At the same time, pilot models were constructed, and simulation was made for the standard case. Moreover, an analysis was conducted of the relation between economic growth and motorization in each country of the world as the basic data preparation on energy consumption in the transportation sector. (NEDO)

  12. FY 2001 report on the coal engineer training project. Advanced course; 2001 nendo sekitan gijutsusha yose jigyo. Jokyu kosu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    The paper summed up the details of the training in the coal engineer training project (advanced course) carried out in FY 2001. The term of training was from June 1 to November 14, 2001. In the business training, lectures were given on coal geology, coal exploration technology, coal mining technology, draft survey, coal sampling and analysis method, maritime freight transport mainly of coal, coal utilization technology, environmental protection technology related to coal utilization, projects on overseas coal development, physical properties/chemical characteristics and usage of coal, and coal situation in China. In the inspection training, inspectional visits were paid to Taiheiyo Coal Mining Co., Noshiro Power Plant of the Tohoku Electric Power Co., Kumagaya Plant of Taiheiyo Cement Corp. and Keihin Steelworks of NKK Corp. In the training overseas, inspectional visits were paid to the following in Australia: coal mines of Moonee, Rix's Creek, West Wallsend, Bloomfield, Beltana, Bulga, South Bulga, Mt. Thorley, Warkworth, Liddell, Wambo, Mount Owen, Camberwell, etc. and harbors of Port Newcastle, Port Kembla Coal Terminal, etc. (NEDO)

  13. Fiscal 1999 research achievement report on the development of SNPs related technologies; 1999 nendo SNPs kanren gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop specimen processing technologies for modifying and enabling various kinds of specimens to automatically undergo SNP (single nucleotide polymorphism) analysis for medicine development and clinical diagnostic activities and to develop technologies and apparatuses to enable rapid, inexpensive, and simple search and analysis of SNPs using DNA (deoxyribonucleic acid) chips and mass spectrometry. Activities are conducted in the four fields involving (1) the development of a practical clinical system for rapid detection and analysis of SNPs, (2) research and development of an SNP scoring system using bar-coded oligonucleotides and magnetic beads, (3) research and development of a high-speed SNP analysis system using a mass spectrometer, and (4) the development of a high throughput SNP analysis line. Efforts exerted in field (1) involve a protein fixation method using plasma polymerization and its application to DNA arrays, development of an SNP detection method using human genomes, construction of a rapid DNA detection device using an electric field, development of an SNP analysis system using the solid phase HPA (hybridization protection assay) method, and SNP analysis using solid phase ligation. (NEDO)

  14. Fiscal 1995 investigation on biological fixation of carbon dioxide; 1995 nendo seibutsuteki CO2 kotei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To cope with the global warming caused by CO2, an investigation was conducted into biological fixation. It is necessary to make a many-sided and comprehensive study on the mechanism of CO2 fixation, the scale (area and carbon holding density), the rate and the environmental impact of the introduction of the technology and the technical problems, and to make a quantitative evaluation of each of the methods in order to make them practical proposals. The global ecosystem is classified into the land biota and ocean biota, and each typical ecosystem was surveyed in terms of the surface area, the carbon holding amount (presently existing amount), the net primary production amount, the required nutrient salt amount, the transpiration rate, etc. Next, a discussion was made on the increasing effect of the carbon fixation amount by changing the present ecosystem from the aspect of scale and rate. At the same time, a study was carried out of energy efficiency, economical efficiency and problems. Last, elementary technology was taken up which seems to be important for implementing measures for the biological carbon fixation. As to the ocean, it is necessary to obtain information, which is not sufficient to utilize marine biota for CO2 fixation, especially on the mechanism of depth-direction transfer of organism and its quantitative grasp. As to the land, one of the measures is conversion of the ecosystem where the amount of carbon fixed is small to the ecosystem where the amount is large. 249 refs., 58 figs., 51 tabs.

  15. Identificação de Genótipos de Feijão-caupi Tolerantes a Acidez em um Latossolo Vermelho-Amarelo do Estado de Roraima = Identification of cowpea genotypes sensitivity to acidicy conditions in an Oxisol of Roraima State (Brazil.

    Directory of Open Access Journals (Sweden)

    Sandra Cátia Pereira Uchôa

    2007-12-01

    Full Text Available O presente trabalho foi realizado com o objetivo de identificar genótipos de feijão-caupi (Vigna unguiculata (L Walp., tolerantes à acidez. O trabalho foi realizado em casa de vegetação localizada no Campus do Cauamé, da Universidade Federal de Roraima, utilizando um Latossolo Vermelho-Amarelo de Boa Vista-RR. Foi adotado o delineamento experimental de Blocos Inteiramente Casualizados em esquema fatorial 2 x 5 x 10 com três repetições. Os tratamentos resultaram de duas formas de localização do calcário (localizada e não-localizada, 5 profundidades (0-5; 5-10; 10-15; 15-20; 20-25 cm e 10 genótipos de feijão-caupi(IT85D-3428-4-R2,4-HM; Apiaú; Hikari Graúdo; Pretinho Precoce 1; IT85D-3428-4-3-HP; USA; UFRR Grão Verde; BRS-Mazagão; Canapum e Sempre Verde. A unidade experimental foi constituída por 2dm3 de solo, dispostos em tubo de PVC com 25cm de altura,10cm de diâmetro e duas plantas de feijão. Os tubos foram confeccionados por meio da junção de 5 anéis com 5 cm cada, sendo que no anel inferior foi colocada uma placa delgada de isopor para permitir a acomodação do solo. Aos 40 dias após a emergência, as plantas foram coletadas, sendo determinada à produção de matéria seca das raízes e parte aérea. Os genótipos IT85D-3428-4-3-HP e UFRRGRÃO VERDE foram classificados como sendo de baixa tolerância, os genótipos USA, BRS-Mazagão, IT85D-3428-4-R2,4-HM e Sempre Verde, medianamente tolerantes e os genótipos Apiaú, Hikari Graúdo, Pretinho Precoce 1 e Canapum, tolerantes à acidez.= This research was carried out objecting to identify the sensibility of cowpea (Vigna unguiculata (L Walp genotypes to acidity conditions. The experiment was installed in a greenhouse located at Campus of Cauamé (Universidade Federal de Roraima in an oxisol of Roraima State (Brazil. The experimental design adopted was a completely andomized blocks in a factorial scheme 2 x 5 x 10 with three replicates. The terms of this factorial

  16. Fiscal 1999 basic survey report for promotion of joint implementation. Plan for repowering Ashuganji thermal power station; 1999 nendo Ashuganji karyoku hatsudensho no repowering keikaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A study is conducted of a plan to repower the Ashuganji thermal power station, the People's Republic of Bangladesh, with the plan to be connected to the clean development mechanism (CDM). For conversion of the existing No. 3, No. 4, and No. 5 generators (each outputting 150MW) into full fired heat recovery combined cycle generators, 31MW gas turbines are added, one to each of the three. The construction cost is calculated to be 14,000-million yen. Fuel (natural gas) will be saved by 28kt/year/generator, the three saving 2.1-million tons in total in 25 years. There will be a CO2 reduction of 77kt/year/generator, the total reduction to be 5.8-million tons in 25 years for the three generators. Then payback is assessed. In the main case (with the repowering-created increase in output to be used to cover the current power supply shortage), where the internal rate of return of 8.09% is much lower than the discount rate of 15.5% during the 10-year period for payback in case of financing by private funds, the discounted present worth is predicted to be negative and then the project is not feasible. Since there will be no problems about the repayment of borrowed money, however, it is hoped that low-interest special yen credit will be granted for the elimination of chronic power shortage. When it comes to international emission trading (550 yen/ton of CO2), payback is again found to be impossible. (NEDO)

  17. Report on an investigation into heat pumps in China in fiscal 1995; 1995 nendo Chugoku ni okeru heat pump system ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper surveyed the present status, the status of spread, and the technical development of the technology of heat pumps for residential and industrial uses in China. Main examples of installation of heat pumps are cited below: steam drive absorption type refrigerators in Beijing; sea water heat source turbo heat pumps in Qingdao; hot water drive absorption type refrigerators in Beijing; oil-fueled absorption type water cooling and heating appliances in Beijing; ice latent heat storage airconditioning systems using electrically-driven screw chiller in Beijing; temperature rising systems using electrically-driven heat pump of the solar energy utilization warm water swimming pool in Guangdong Province; cooling water supply using waste heat utilization absorption type refrigerator of the alcohol plant in Shandong Province; timber drying systems using electrically-driven heat pump, and marine product cultivation systems in Quangdong Province; distillation systems using steam turbine heat pump in Jiangxi Province. The demand for heat pumps is expected to be 20 million units under the 9th 5-year plan, and the development of equipment is thought to go toward promotion of energy conservation, low noise, multi-type or multi-functional air conditioning equipment, and computer use. 137 figs., 40 tabs.

  18. Fiscal 1998 research report. Construction model project of the human sensory database; 1998 nendo ningen kankaku database kochiku model jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1998 research result on construction of the human sensory database. The human sensory database for evaluating working environment was constructed on the basis of the measurement result on human sensory data (stress and fatigue) of 400 examinees at fields (transport field, control room and office) and in a laboratory. By using the newly developed standard measurement protocol for evaluating summer clothing (shirt, slacks and underwear), the database composed of the evaluation experiment results and the comparative experiment results on human physiological and sensory data of aged and young people was constructed. The database is featured by easy retrieval of various information concerned corresponding to requirements of tasks and use purposes. For evaluating the mass data with large time variation read corresponding to use purposes for every scene, the data detection support technique was adopted paying attention to physical and psychological variable phases, and mind and body events. A meaning of reaction and a hint for necessary measures are showed for every phase and event. (NEDO)

  19. Leading survey and research report for fiscal 1999. Survey and research on supercompiler technology; 1999 nendo supercompiler technology no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Survey and research are conducted into the global computing technology and the next-generation parallel computer for their compiler technology and programming environment-related technology, which is for the preparation of basic key technologies for the embodiment of high-performance computing for the next generation, and efforts are exerted to extract and define technological problems and to deliberate a research system to achieve the goal. This fiscal year's achievements are mentioned below. Two territories were provided to be respectively covered by a Parallel Compiler Working Group and a Global Computing Working Group whose activities centered about overseas surveys and short-term reception of researchers from abroad. The Parallel Compiler Working Group was engaged in (1) the technological survey of the latest parallel compiler technology and, in its effort to execute researches under the project, in (2) the materialization of the contents of technology research and development and in (3) the materialization of a technology research and development system. The Global Computing Working Group was engaged in (1) the technological survey of the latest high-performance global computing and in (2) the survey of fields to accept global computing application. (NEDO)

  20. Fiscal 1992 survey report. Survey of research trends in search for important research domains; 1992 nendo juten kenkyu ryoiki tansaku no tame no kenkyu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    For contribution of suggestions for establishing directions and concrete tasks for new industrial technology research and development projects, a survey is conducted about trends of industrial technology development and into research domains where importance will gather in the future, for which development trends are studied such as limiting, providing of intelligence, and advanced composition. In this report, domains expected to become important in the future are investigated. Important subjects are found in the domains of the space limiting (micromachining, atom/molecule manipulation, microanalysis, etc.), the time limiting (super-spacetime processing, quantum device, femtosecond technology, 4-dimensional device, etc.), biomimetics and providing of intelligence (intelligent material, neural network, genetic algorithm, artificial life, sensor fusion, intelligent robot, etc.). In addition to these, 'ultrastructure that learns from organisms,' 'intensive interaction system,' and 'nonlinearity/chaos technology' are proposed as promising fields of development. Since Japan is traditionally strong in hardware technologies relating to micromachining and substance/material processing, good results will be attained when the industrial, governmental, and academic circles exert endeavors. (NEDO)

  1. Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (photovoltaic power generation); Taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    This report summarizes the research result on the guide for developing solar cells. The report includes (1) standard measurement method for solar cells, (2) system configuration and installation site, (3) optimum design and profitability of solar cells and (4) raw materials and pollution prevention. In the 1st research, study was made on the standard for solar radiation intensity, the definition and measurement methods for spectral profiles, and the measurement conditions for solar cells. In the 2nd research, study was made on various basic data for the scale of photovoltaic power systems. In the 3rd research, since it is necessary to obtain characteristics of solar cells with any profiles of physical constants such as impurity, minority carrier life and mobility by simulation of solar cell actions, research was made on the measurement method of minority carrier lives by using a prepared computer program. Technical and economical comparisons were also made between Si solar cells with various structures. In the 4th research, survey was made on various data for compound semiconductors, and study was made on industrial waste pollution. (NEDO)

  2. Report on results of research. Basic studies on characteristics of coal char gasification under pressure; Sekitan char no kaatsuka ni okeru gas ka tokuseino kiso kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This paper explains basic studies on characteristics of coal char gasification under pressure. Hydro-gasification of coal needs as a gasifying agent a large amount of hydrogen, which is effectively produced by the water gasification of exhaust unreacted residual char. In fiscal 1975, gasification was tested on Taiheiyo coal carbonized char by an atmospheric fluidized gasifier of 28 mm bore. In fiscal 1976, experiment was conducted under pressure by fully improving the auxiliary safety equipment. The char and gas yield increased with higher pressure in pressurized carbonization by an autoclave. In fiscal 1977, clinker was successfully prevented by using quartz sand for a fluidized medium. In fiscal 1978, two-stage continuous gasification was examined. In fiscal 1979, correlation was determined between operation factors such as gasification pressure, temperature, etc., and clinker formation/char reactivity. An experiment was conducted for particle pop-out using a pressurized fluidized bed of 100 mm inner diameter, with the pop-out quantity found to be proportional to the 0.38th power of a pressure. A high pressure fluidized gasifier was built having a char processing capacity of 1 t/day, 20 atmospheric pressure, and an inner diameter of 100 mm. In fiscal 1980, this device was continuously operated, elucidating problems for the practicability. (NEDO)

  3. Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

  4. Fiscal 1993 report on technological results. R and D on micromachine technology; 1993 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-01

    Researches on basic element technology of micromachines are conducted with the view of establishing a mechanical system constituted of minute functional elements that perform autonomous operations in a narrow small part of complicated equipment in a power station for example or in a living body. The areas of activity are 1. research on micro actuators and 2. research on basic technology of micromachine; 1 is classified into researches of (1) shape-memory actuator, (2) bending and stretching type actuator, and (3) integrated micro actuator, while 2 is classified into researches of (1) total system for medical diagnosis, (2) micro tactile sensing technology and laser applied diagnosis/treatment technology, and (3) blood pressure/blood circulation sensing technology. In 1-(1), a chemo-mechanical actuator was studied using a shape memory alloy (SMA) and a high polymer gel, and in 1-(2), an SMA and bimetal were employed as a source of the driving force. Further, examination was also made on a fluid driving type actuator. (NEDO)

  5. Fiscal 1995 survey report. Study of new energy vision formulation for Kawasaki City, Kanagawa Prefecture; 1995 nendo Kawasaki shi shin energy vision sakutei kentou chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was conducted of the current status of energy supply/demand, future problems, goals of the energy policy, basic plan, and so forth, for the formulation of a new energy vision for the city. Concerning energy supply/demand, studies were made of each sector, area, and energy source. In the study of energy demand, it was discovered that, although the industrial sector in the coastal region remained important, the residential/commercial sector was gathering weight and that the city was serving as an energy supply base for the neighboring areas. In the study of new energy, it was found that the available amount of solar energy resources was enormous, that the Tama river fresh water and the Keihin canal seawater constituted a promising source of temperature difference energy, and that sewage energy, transformation station exhaust heat, LNG (liquefied natural gas) cold heat, and so forth, were also available as energy sources. Taken up for discussion as possible new energy introduction models were gas engine cogeneration, photovoltaic power generation, district heat supply utilizing temperature difference energy, and so forth. (NEDO)

  6. Geothermal development promotion survey report. No. 26. Akan region; 1988-1991 chinetsu kaihatsu sokushin chosa hokokusho. No. 26 Akan chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The results of surveys conducted in the Akan region, Hokkaido, in fiscal 1988-1990 are compiled in this report. Conducted were a geological/alteration zone survey, geochemical survey, gravity prospecting, electromagnetic surveillance (simplified magnetotelluric method), electric prospecting (Schlumberger method), electric prospecting (mise-a-la-masse method), heat flow rate survey, test boring, geothermal water survey, environmental impact survey, and so forth. The surveys resulted in conclusions mentioned below. Fractures running NE-SW are dominant, and those closely related to prominent geothermal signs are found in the Akan Seibu fault group in the western part of the Akan region. The test boring results show that there are high-temperature zones of 292.1 degrees C, 194.9 degrees C, and 245.9 degrees C. Geothermal fluids were discharged by well N2-AK-7 at a rate of 4.7-4.8 t/h in steam and 0.3-0.4 t/h in neutral SO{sub 4}-HCO{sub 3} type geothermal water. High-temperature steam-dominated geothermal resources are expected to exist deep in the ground in this region, and the area where the Akan Seibu fault group is distributed may be named as a location containing promising geothermal resources. (NEDO)

  7. FY 2000 report on the results of the R and D of fundamental technologies for semi conductivity applications; 2000 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    In relation to the project on the R and D of fundamental technologies for semi conductivity applications, the FY 2000 results were summed up. As to the study of the high temperature superconductivity mechanism, it was found out that a theoretical model of the strong scattering limit in d-wave superconductor can be used for the breaking of superconductivity due to Zn impurities. Concerning the study of the critical current mechanism, the elucidation was proceeded with of the magnetic flux pinning and grain-boundary conduction mechanism. Relating to the development of element technology of bulks with great electromagnetic force, the mechanical strength of superconducting bulk materials was raised to 100MPa or more by the epoxy resin impregnation method. As to the development of the basic technology for fabrication of high next-generation current conductors, the expansion was confirmed of conditions for growing single grains in the zone-melt process for very fine filaments. About the development of technology of single crystal substrates, in the development of the pseudo single crystalline film growth process by LPE method, a yield ratio of high quality crystal of 63% was achieved. Concerning the development of technology of thin film/multi-layer, the area of uniform composition/thickness of NdBa{sub 2}Cu{sub 3}O{sub 7-x} MOCVD films was enlarged up to 20mm square. (NEDO)

  8. Fiscal 1999 leading research report. Research on 3-D cell tissue module technology; 1999 nendo sanjigen saibo soshiki module kogaku chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For forming cell tissues alternative to bio-tissues, this research targets the technology for forming bio-tissue modules by cultivating 3-D cell tissues from various kinds of cells. In fiscal 1999, research was made on various issues of element technologies necessary for forming module structure of bio-tissues, and study was also made on the application of 3-D cell tissue module engineering to industrial fields. Survey was made on element technologies and solutions supporting such engineering, and in addition, on progressive conditions of cell cultivation techniques, and concrete techniques for expressing cell functions. Research was made on a cell behavior under physicochemical stimulus environment to study the optimum environment for cell multiplication and function expression. Further research was made on state analysis of cells, in particular, fast precise measurement techniques of activation or malignant of cells and secretion of toxic substances by physical/optical analytical evaluation techniques such as photo-CT and spectroscopic analysis, and biochemical analysis techniques using bio-sensors. Study was also made on successful development and application cases of practical bio-artificial organs in western countries. (NEDO)

  9. Research and development on fusion zones in fiscal 1999. Third volume. Biomolecular mechanism and design; 1999 nendo yugo ryoiki kenkyu kaihatsu seika hokokusho. 3. Biomolecular mechanism and design

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    It was intended to elucidate the structures of living organisms having excellent functions and the principles of these functions, and to create cells, structural bodies and molecular mechanisms that substitute these functions outside the bodies of the living organisms. Therefore, research and development has been performed on the fundamental technologies, whose achievements are compiled. In the research of creating cultured bones and cartilages, marrow cells and cartilage cells were cultured while providing physiological active materials and mechanical stimulation. Porous ceramics and porous biodegradating polymers coated with collagen were used as the substrate materials to have created artificial cartilages. In the research of structural change in a molecule motor, a low temperature electron microscope was used to make the structure visualized successfully for the first time. In the research of creating an artificial liver, the world's first cells like stem cells separated and refined from liver cells were cultured three dimensionally in a bio-reactor using special cultivation solution to have established the basic technology. In the research of libozyme, sensor function and high catalytic function were realized successfully in the cells by dimerizing libozymes. (NEDO)

  10. Fiscal 1999 survey report. Survey of effect of energy efficiency improvement on global environment; 1999 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Analyses are conducted into consideration given to global warming measures in the 3rd assessment report of the Intergovernmental Panel on Climate Change (IPCC) and into technology transfer from developed nations to developing nations in the Asia-Pacific region etc. to contribute to their energy efficiency improvement. The aim is to present data for deliberation as to how future energy efficiency improvement measures should be in the Asia-Pacific region. The chapters (Chapter 0 through Chapter 10) of the report to be worked out by Working Group III deeply involved in energy problems are 0) Introduction, 1) Scope of the report; 2) Socio-economic and emissions scenarios; 3) Technical and economic potential of GHG (greenhouse gas) emissions reduction; 4) Technical and economic potential of biological CO2 mitigation options; 5) Barriers, opportunities and market potential of technologies and practices; 6) Policies, measures and instruments; 7) Costing methodologies; 8) Global, regional and national costs and ancillary benefits of mitigation; 9) Sector costs and ancillary benefits of mitigation; and 10) Decision making frameworks. As the result of the survey, some actual technology transfer implementations are introduced covering branches closely related to energy efficiency improvement, which are branches of construction, traffic, industry, energy supply, and wastes. (NEDO)

  11. Fiscal 1999 survey report. Survey of leading countries' approaches to biomass energy development; 1999 nendo shuyokoku ni okeru biomass energy kaihatsu eno torikumi ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey aims to help Japan deliberate its future biomass energy development strategy including the course Japan is to follow in its research and development of biomass energy by clarifying leading countries' approaches to the subject matter and trends of their research and development efforts in this connection. The states of biomass energy development in the U.S. and Europe are reported. In the U.S., President Clinton issued Executive Order 13134 on August 12, 1999, regarding bio-based products and bioenergy development. In this country, bioenergy and bio-based production technologies have developed to reach a stage where business pays, and commercial plants are in service. The U.S. Administration mentions as a strategy the efficient development of the bioenergy industry. In Europe, where resources are versatile and local, it is difficult to assess the economy of scale, and small-scale development efforts are being accumulated. Practical technologies under development mostly involve direct combustion. European measures are similar to U.S. measures in that such political goals as local development and employment promotion are firmly woven into them. (NEDO)

  12. Fiscal 2000 survey report. Survey of DSM status in Europe centering about thermal storage; 2000 nendo Oshu ni okeru chikunetsu wo chushin to shita DSM jokyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In search of measures for popularizing thermal storage technology in Japan, investigations were conducted into the conditions of electric power and the state of DSM (demand side management) in Italy, Spain, Portugal, and Greece whose climate is similar to Japan's. The results of the effort were edited and classified into six items, which are (1) power conditions, (2) DSM status, (3) popularity of thermal storage, (4) merits of thermal storage, (5) measures for thermal storage popularization, and (6) propositions to Japan. In all the countries, the power demand peak has shifted to the summer season or the difference in demand for power between summer and winter has decreased and, except in the case of Greece, the load factor has increased, these due to the increase in demand for power for cooling equipment. In Greece, the load factor has decreased since the peak shifted to summer. In every country, the rate schedule based on season of the year and time of the day is treated as a basic incentive for DSM. Except in Greece, there is no summer demand suppression type DSM menu and efforts are being exerted rather to have loads built in off-peak time zones. As for thermal storage systems in use, they are mostly of the ice-aided type. Those in the residential/commercial sector are on the increase, and it is estimated that 50% of ice thermal storage systems will be found in this sector in 2000. (NEDO)

  13. Fiscal 1974 Sunshine Project result report. Research on solar energy utilization systems (solar heat power generation); 1974 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyonetsu hatsuden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    This report summarizes the fiscal 1974 research result on solar heat power generation. The following are promising as solar heat power plant sites in Japan: Large-scale sites such as the foot of volcanos, riverbed, railway site and road, medium-scale sites such as isolated island, saltpan site and industrial park, and small-scale sites such as factory site, factory roof floor, housing complex, warehouse and school. Based on the primary concept design of both curved reflector type and tower type 1,000kW class solar heat power plants, various requirements were clarified roughly. It was clarified that food, fiber and non-ferrous metal factories can cover 80-90% of their thermal energy requirements with high- temperature solar heat, while factories related to food and fiber can cover even nearly 100% of their electric power requirements with solar heat. Study was also made on specifications of a solar simulator as common use facility necessary for characteristic evaluation of equipment and materials for solar heat power generation systems. (NEDO)

  14. Interim report on research and development of magnetohydrodynamic (MHD) power generation. General remarks; Denji ryutai (MHD) hatsuden kenkyu kaihatsu chukan hokokusho. Soron

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1973-08-01

    This report covers the MHD power generation research and development project which has been under way for 7 years since fiscal 1966, and contains guidelines to follow in the next 3 years during which studies will continue toward the consummation of the project. Subjected to research and development under this project are the development of superconductive magnets and helium refrigeration/liquefaction equipment, clarification of the power generation characteristics of the 1,000kW-class MHD (magnetohydrodynamic) power generator and of a test machine designed for a long-term operation, etc. Since they contain many basic studies, the efforts are being exerted primarily by the Electrotechnical Laboratory. In the research and development of MHD power generation characteristics, a power generation experiment is conducted through oxygen combustion in a hot wall channel, with the combustor and insulation against the Hall voltage improved. In this test, a maximum output of 1,182kW is achieved under the conditions of a flow rate of 2.9kg/s, a thermal input of 24.6MW, and a flux density of 3.2T. Since there are some problems to solve in connection with the stability of MHD power generation characteristics, durability of the MHD power generation channel, characteristics of heat exchanger system, measures for NOx reduction, etc., some more deliberation is necessary before taking the next research and development step. (NEDO)

  15. Regional new energy vision formulation survey for Makurazaki City. Fiscal 2001 report; 2001 nendo Makurazaki shi chiiki shin energy vision sakutei tou chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for elevating people's consciousness of such in Makurazaki City, Kagoshima Prefecture, surveys and studies were conducted concerning the energy demand of the city, the amount of new energy resources in existence, and new energy introduction plans, and then a vision was formulated. The city's energy demand in fiscal 1999 is estimated at approximately 3,206 TJ, with the industrial sector demanding 1,820 TJ, the residential and commercial sector demanding 701 TJ, and the transportation sector demanding 684 TJ. Energy consuming industries in this prefecture are fisheries industry and food industry. Pilot projects for new energy introduction were discussed, which included the introduction of photovoltaic power into the city hall, primary and junior high schools, a school meal providing center, and a city-managed hospital; installation of hybrid power-lighted light at the city hall, along the Kedo river, and in the Hinokami park; introduction of a solar heat utilization system into a nursing home for elderly people; introduction of wind power into education facilities; conversion of waste of cooking oil into diesel fuel; introduction of clean energy vehicles into public service; and new energy projects to be contracted to the private sector. (NEDO)

  16. Evaluation report on the design of solid catalysts for saving energy in petrochemical industry; Sekiyu kagaku no tame no sho energy gata kotai shokubai sekkei hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The aim is to improve on hydrocarbon oxidation which is a difficult reaction (analogous to combustion and having potential for heat generation or explosion, with restrictions therefore imposed on reaction conditions) by use of a catalyst supporting porous membrane. The fiscal 1999-2000 results are stated. In this effort, the target reaction is promoted by a catalyst supported by a porous membrane while combustion is controlled by the said porous membrane that separates oxygen and hydrocarbon from each other. Such a design was not available since a catalyst supporting inorganic membrane withstanding so high a temperature was difficult to prepare. Recently, however, a porous membrane with its pores regulated to microstructural dimensions was developed. The activity of a Pd membrane catalyst is evaluated in view of the degree of oxidation of propylene, cyclohexene, and benzene. It is then found that hydrogen that has passed the Pd membrane participates in the reaction. In a propylene oxidation test using a membrane type Ag/Al{sub 2}O{sub 3} catalyst, it is found that acetone is generated and that oxygen after passing through the membrane participates in the reaction. Methods are studied for preparing a metal membrane in which the catalyst system comprises a catalyst supporting porous membrane and a Pd membrane. In the fabrication of metal membranes, a highly selective hydrogen permeable membrane is stably prepared by the thermal CVD (chemical vapor deposition) method. (NEDO)

  17. Fiscal 2000 report on results of R and D of welfare techno-system in Mitaka City; 2000 nendo walfare techno system kenkyu kaihatsu (Mitaka) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Studies were made for the purpose of probing effects of utilizing body sensory game machines for the functional recovery training and exercise of the elderly and handicapped, with the fiscal 2000 results reported. In the verification by existing game machines, a game center was made available free of charge, providing free experience for the elderly, with the image traced of the elderly for the game machines based on the record of the machines used, questionnaires and interviews. In addition, four body-sensory game machines that were supposed to be effective for the exercise of the joints were installed in a day care center for six months, with a verification test performed on the adaptability of the elderly to the speed and the like of the game machines. In the development of a game machine intended for the exercise of the lower extremities, researchers tackled the development of a game machine in which an entertainment/amusement nature was added to the exercise of the lower extremities. An experimental model was developed based on a principle providing a virtual reality as if the user were walking in a tourist area of scenic beauty by moving a scenery linked with a foot pedal type exercising pattern. (NEDO)

  18. Wind power development field test project at Okkobe-cho. Close survey on wind conditions; Okkobecho ni okeru furyoku kaihatsu field test jigyo (fukyo seisa) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    A survey was made on regional wind conditions on the assumption that a wind power generator was installed around Okkobe Rakuno-no-oka, Okkobe-cho, Monbetsu-gun, Hokkaido. The survey period was one year from Oct., 1998 to Sept., 1999. The observations were carried out on the average wind velocity, average wind direction, standard deviation of velocity, and the maximum instantaneous wind velocity. With a fixed point observation at 20 m above ground, and with the minimum observation time unit of 10 minutes, an average value during the 10 minutes was determined as the measurement of each category. However, the maximum instantaneous wind velocity was determined on the measurement with the minimum observation time unit of 2 seconds. The average wind velocity was 4.8 m/s, the maximum wind velocity during the period was 29.9 m/s, the prevailing wind direction was WSW (17.1%), the wind axis was WSW-ENE, and the total occurrence rate of wind direction was 51.1%. The intensity of turbulence was 0.19 at a wind velocity of 2.0 m/s or above and was 0.16 at 4.0 m/s or above. An estimated annual operation rate of a windmill was 59-77% using the rated value of a 150 kW, 300 kW and 750 kW class windmills. (NEDO)

  19. Survey report on establishing a new energy and energy saving vision in Fukui Prefecture; Fukuiken shin energy sho energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys and discussions were given on establishing a new energy and energy saving vision in Fukui Prefecture. The energy consumption in Fukui Prefecture for fiscal 1996 was 25242 x 1 billion kcal, being 0.7% of the nation's total consumption. The per capita energy consumption is about a little greater than the national average. The energy consumption structure is characterized by large consumption in the transportation department, especially in automotive consumption. Carbon dioxide discharge is as little as being ranked 13th among all the prefectures in Japan. The availability and usable quantity of new energies in Fukui Prefecture is estimated as 1659939 x 10{sup 3} kWh/year as electric power, 9436 x 10{sup 6} kcal/year as gas, and 3536720 x 10{sup 6} kcal/year as heat. Energies could be saved most greatly by enhancing automotive fuel consumption rate, followed by effects of energy saving activities based on spontaneous action plans established by the industrial departments. New energies selected to be worked on importantly include: solar energy power generation, wind power generation, clean energy fueled automobiles, wastes energy, co-generation and solar heat. (NEDO)

  20. Fiscal 1998 research report on the total electric power loss reduction project for Myanmer; 1998 nendo Myanmer koku denryoku soshitsu sogo teigen project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of Japanese clean development mechanism, study was made on reduction of greenhouse effect gas emission from thermal power plants by reduction of power transmission and distribution losses of power systems in Myanmer. Study was made on technical power transmission and distribution losses for the national grid transmission system, 33kV sub- transmission system of Thaketa substation in Yangong city, and 6.6kV and 400V distribution systems of Latha and Lanmadaw townships in the downtown area of Yangong. Countermeasures for power loss reduction were considered on the basis of the study result. The loss reduction project plan includes a construction cost of 5,134,000US$, loss reduction of 7,726kW, and loss reduction of 33,213,000kWh. The project feasibility and profitability were evaluated by comparison between a financial internal rate of return (FIRR) and an opportunity cost assuming that a discount rate is the opportunity cost. As a result, FIRR was 17.36% and the discount rate was 8.89% in Myanmer. (NEDO)

  1. Wind power development field test project at Hirashima, Sakito-cho. Detailed wind characteristics survey; Sakitocho Hirashima ni okeru furyoku kaihatsu field test jigyo (fukyo seisa) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    A detailed wind characteristics survey was conducted at Hirashima, Sakito-cho, Nishisonogi-gun, Nagasaki Prefecture, on the assumption that a wind power generation system would be constructed. The survey was a 1-year project from October 1998 through September 1999, and wind characteristics such as the average wind speed, average wind direction, standard deviation of wind velocity, and the maximum instantaneous wind speed were observed. The observation point was fixed at 20m above ground, the minimum time unit for observation was 10 minutes, and the 10-minute average value was defined as the measured value. For the maximum instantaneous wind speed, the minimum time unit for observation was set to be 2 seconds. The yearly average wind speed was 7.1m/s and the maximum wind speed in the period was 37m/s. Winds came prevalently from N (13.9%), and then from NNE (13.3%), NW (12.2%), and NE (10.7%). The total wind direction occurrence rate involving the 4 directions was 50.1%. Turbulence intensity was 0.14 at wind speed 2.0m/s or more and 0.12 at wind speed 4.0m/s or more. Estimated wind turbine yearly operating factors of 77-87% were obtained using rated values of a 150kW, 300kW, and 750kW-class wind turbines. (NEDO)

  2. Wind power development field test project at Maruyama-machi. Close survey on wind conditions; Maruyamamachi ni okeru furyoku kaihatsu field test jigyo (fukyo seisa) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    A survey was made on wind conditions in Maruyama-machi, Awa-gun, Chiba prefecture, on the assumption that a wind power generation system was installed therein. The survey period was one year from Oct., 1998 to Sept., 1999. The observations were carried out on the average wind velocity, average wind direction, standard deviation of velocity, and the maximum instantaneous wind velocity. With a fixed point observation at 20 m above ground, and with the minimum observation time unit of 10 minutes, an average value during the 10 minutes was determined as the measurement of each category. However, the maximum instantaneous wind velocity was determined on the measurement with the minimum observation time unit of 2 seconds. The average annual wind velocity was 3.5 m/s, the maximum wind velocity during the period was 27 m/s, and the wind axis was WSW-ENE, with the total occurrence rate of the wind direction 44.1%. The intensity of turbulence was 0.23 at a wind velocity of 2.0 m/s or above and was 0.22 at 4.0 m/s or above. An estimated annual operation rate of a windmill was 40-60% using the rated value of a 150 kW, 300 kW and 750 kW class windmills. (NEDO)

  3. Wind power development field test project at Ashibe-cho. Detailed wind characteristics survey; Ashibecho ni okeru furyoku kaihatsu field test jigyo (fukyo seisa) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    A detailed wind characteristics survey was conducted at Ashibe-cho, Iki-gun, Nagasaki Prefecture, on the assumption that a wind power generation system would be constructed. The survey was a 1-year project from October 1998 through September 1999, and wind characteristics such as the average wind speed, average wind direction, standard deviation of wind velocity, and the maximum instantaneous wind speed were observed. The observation point was fixed at 20m above ground, the minimum time unit for observation was 10 minutes, and the 10-minute average value was defined as the measured value. For the maximum instantaneous wind speed, the minimum time unit for observation was set to be 2 seconds. The yearly average wind speed was 5.8m/s and the maximum wind speed in the period was 35m/s. Winds came from the prevailing direction of NE (21.3%), and then from NNE (14.7%) and ENE (7.9%). The wind axis was in the NE-SW direction, and the total wind direction occurrence rate from the 6 directions was 60.2%. Turbulence intensity was 0.19 at wind speed 2.0m/s or more and 0.17 at wind speed 4.0m/s or more. Estimated wind turbine yearly operating factors of 66-84% were obtained using rated values of a 150kW, 300kW, and 750kW-class wind turbines. (NEDO)

  4. Fiscal 2000 research report on the technology for utilizing intracellular protein transport; 2000 nendo saibonai tanpakushitsu yuso kino riyo gijutsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research was conducted for the establishment of 'intracellular transport engineering' for collecting eucaryotic proteins having cytotoxicity and activated proteins having escaped decomposition into an appropriate intracellular organelle by artificially manipulating the intracellular transport system for proteins in eucaryotes. In this fiscal year, element technologies and tasks necessary for the transport and activation of intracellular proteins in eucaryotes are extracted, and research was conducted on relevant patents. In a survey of the latest trends of research and development, attention was directed mainly at cells or organelles, and the details of progress in the last one year were investigated and reported, which were related to the functions of single membrane organelles excluding for double membrane bound organelles, e.g., mitochondria and chloroplast, etc., that have unique DNA (deoxyribonucleic acid) and to the molecular mechanism of transport of protein to each organelle. Furthermore, relative to each organelle, deployment of protein transport function application technology was taken up. (NEDO)

  5. Report on the project on working out the new energy vision of Hisai City; 2001 nendo Hisai shi chiiki shin energy vision sakutei tou jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Hisai City, Mie Prefecture, an investigational study was conducted of the energy demand structure, existence amount of new energy and project for new energy introduction, and a vision was worked out. The energy consumption amount of the city was 21,500 lorries in the industrial sector, 11,200 lorries in the transportation sector, 2,700 lorries in the business sector and 2,400 lorries in the residential sector in terms of tank-lorry loaded oil. As features, the following were cited: growth in the transportation sector, mostly in automobiles, was great; growth in the electric power consumption in the residential sector was great. As the project for new energy introduction, the following were supposed and studied in terms of the economical efficiency and environmental acceptability: introduction of cogeneration to hospital; introduction of ligneous biomass power generation to hospital; substitution of wood burning boiler for A heavy oil boiler for hot water supply use; introduction of photovoltaic power generation for home use and business use; introduction of solar heat use hot water supply device. (NEDO)

  6. Fiscal 1999 report on result of the model project for waste heat recovery in hot blast stove; 1999 nendo netsufuro hainetsu kaishu model jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    For the purpose of curtailing energy consumption of the steel industry, a heavy energy consuming industry in China, a model project was carried out for waste heat recovery in a hot blast stove, with the fiscal 1999 results reported. In the process of this project, a heat exchanger for recovering heat is installed in the exhaust gas flue of a hot blast stove in ironworks, with sensible heat recovered through a heating medium. The heat exchanger for recovering heat and the preheating heat exchanger, which was installed in the main pipe for blast furnace gas and for combustion air, were connected by pressure piping, with the blast furnace gas and the combustion air preheated. In addition, a heating medium circulating pump for transporting the heating medium is installed, as are an expansion tank for absorbing expansion/contraction due to change in temperature, a heating medium storage tank for accepting the entire heating medium in the system for the maintenance of the equipment, and heating medium feeding pump, for example. This year, on the basis of the 'Agreement Annex', basic designs and detailed designs were performed for each equipment in the waste heat recovering equipment for the hot blast stove. Further, procurement and manufacturing were implemented for various component parts and devices of the waste heat recovering equipment. (NEDO)

  7. Leading research report for fiscal 1999. Fundamental technology of spin electronic device; 1999 nendo spin toronikusu soshi kiban gijutsu kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The project, with attention paid to both spin and charge of electrons, aims to draw the best of the said two attributes of electrons by use of the state of the art in manufacturing technology for the creation of novel electronic devices. The nonvolatile MRAM (magnetic random access memory), which is the nearest to commercialization, is a tunnel device consisting of two sheet-shape ferromagnetic metal electrodes and an insulator film sandwiched between the said two electrodes, with the lower electrode magnetized only in one direction. The tunnel resistance changes when the magnetization direction in the upper electrode changes left and right (1, 0) according to an external writing magnetic field, and this enables nondestructive readout. The upper electrode magnetization direction remains unchanged thanks to hysteresis when the external writing magnetic field is turned off, and this allows the device to serve as a nonvolatile memory device. The device has a potential for higher speeds and enhanced integration. Much is also expected from a spin conduction functional device utilizing spin-dependent electric conduction, spin optical function device, spin quantum calculation directly utilizing quantum state, magnetic field sensor, etc. Their importance is great economically and socially, and technologies relating to magnetism and semiconductor should be merged for their further development. (NEDO)

  8. Report on the geothermal development promotion survey. No.B-7. Kuwanosawa area; Chinetsu kaihatsu sokushin chosa hokokusho. No. B-7 Kuwanosawa chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    The paper summed up the results of the geothermal development promotion survey B 'Kuwanosawa area' which was carried out in Yuzawa city, Akita prefecture, from FY 1998 to FY 1999. In the survey, the following were conducted for the comprehensive analysis: geology/alteration zone survey, gravity exploration, electromagnetic exploration, environmental effect survey, well geology survey by drilling structural boreholes of N11-KN-1 and N12-KN-2, cuttings test, temperature log, temperature recovery test, electrical log, water injection test, etc. The geology in the Kuwanosawa area is composed of Pre-neogene period basement rocks, Neogene system and Quaternary system. In this area, there were recognized no gush of geothermal fluids such as hot spring and fumarolic gas and no obvious geothermal manifestation such as high-temperature places and new geothermal alteration zones. Around N12-KN-2, there exists the geothermal water with comparatively high-temperature/high-Cl concentration which is similar to that in the Wasabizawa area, but how it flows is unknown because there was no lost circulation in the depths of the borehole. Around N11-KN-1, there exists the low-temperature/low-Cl concentration geothermal water originating in meteoric water, and therefore, the area can be a rechargeable area. The Kuwanosawa area is regarded as the periphery of the Wasabizawa-Akinomiya geothermal area. (NEDO)

  9. Report on the survey for working out the new energy vision of the Urugi village area; 2001 nendo Urugi mura chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of promoting the introduction of new energy and enhancing the awareness of it at Urugi Village, Nagano Prefecture, an investigational study was conducted of characteristics of the natural environment/characteristics of social economy of the village, existence amount of new energy, project for new energy introduction, etc., and a vision was worked out. Urugi Village is 800 meters above sea level and in the riches of the Nature being surrounded by mountains on all sides. The population of the village was 734 as of March 1993, which is decreasing by 14-15/y. The aging rate was very high, 32.3%. As the project for new energy introduction, the following were studied: 10kW class photovoltaic power generation facilities to be installed at Furusato-kan and by the road of Hiraya Pass, 2.5kW class wind power generation facilities to be installed at Hiraya Pass for education of new energy, installation of a 10kW class mini hydroelectric power plant supplying power to the auto-camping site, stockbreeding biomass cogeneration which conducts fermentation of the methane from animal feces and garbage generated in Urugi Village, ligneous biomass cogeneration, etc. (NEDO)

  10. Regional new energy vision for Kobuchizawa Town. Eco-energy town - Kobuchizawa; 2001 nendo Kobuchisawa cho chiiki shin energy vision hokokusho. Eco energy town Kobuchisawa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for enhancing people's consciousness of such at Kobuchizawa Town, Yamanashi Prefecture, surveys and studies were conducted on the trend of energy consumption in the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The town consumes 635,021 GJ/year in energy, with the industrial sector consuming 34.6%, the transportation sector 24.8%, the residential sector 21.8%, and the commercial sector 18.7%. The energy sources are electric power, kerosene, LPG, gasoline, gas oil, and heavy oil, as named in the descending order in terms of amount. Studies were made about new energy introduction projects, which included the use of photovoltaic power for outdoor lights, primary schools, nursery schools, the flower park (Fiore Kobuchizawa), mountain huts, and for the Kannondaira sightseeing spot; mini-scale hydroelectric power generation for the maintenance of the Otaki spa and existing water channel utilities; wind power generation for improvement on mountain huts; introduction of clean-energy vehicles; introduction of cogeneration (natural gas); and a business for effectively utilizing biomass. (NEDO)

  11. Research report of fiscal 1997. Basic research on the commercialization of innovative energy technologies; 1997 nendo chosa hokokusho. Kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper summarizes the research result in fiscal 1997 from the basic research results on the commercialization of innovative energy technologies. The target of a photovoltaic power generation market includes isolated power sources (several kWp) for distant places or developing countries, and those (several tens kWp) for personal residences or public facilities. Although the former is mainly promoted in the West, while the latter over the world, their profitability is unsolved. Power plants over several hundreds kWp are in demonstration test. Solar heat power generation of several tens to hundreds MWp is most profitable, however, small-scale one is poor in feasibility. Australia takes an interest in distributed photovoltaic power generation directly connected with actual lives of residents, and has a dominant opinion that desert is useless as large-scale site. This country lays emphasis on protection and maintenance rather than positive use of desert based on a basic cognition that desert is easily changed and broken. The Australian government announced power company`s obligation to use renewable energy by 2%, and a strong organization is scheduled to be newly established. 59 figs., 57 tabs.

  12. Report on achievements in fiscal 1998. Survey on environmental effects from photovoltaic power generation systems; 1998 nendo daikibo taiyoko hatsuden system no kankyo eikyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Different environmental effects may be assumed when large-size photovoltaic power generation systems are installed in vast unutilized lands including deserts. Knowledge having been acquired to date has been put into order on the following subjects as the pre-survey thereon: (1) environmental characteristics of desert areas, (2) discussions on environmental effects from (a) environmental assessment viewpoints, (b) contents of the environmental assessment, and (c) environmental assessment institutions, and (3) the survey policy. In discussing the environmental characteristics, it is revealed that desert areas are neither sterile nor unused, but pasturage and agriculture have been carried out in historical and traditional ways. In discussing the environmental effects, it was recognized that surveys on primary and secondary effects on the environmental are indispensable. With regard to the institutions, there are countries who have and have not the institutions even among the OECD member states. In addition, it was known that environments in the desert areas vary greatly according to the particular areas, whereas there are possibilities of installing the facilities because the effects of the facility locations on the environment are various. Therefore, it was decided to start from the case studies in locations of different types. (NEDO)

  13. FY 1998 report on the R and D of micromachine technology. R and D of micromachine technology; 1998 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the comprehensive investigational study of micromachine technology, the paper aims at clarifying the improvement of functional devices and the future development of micromachine technology for establishment of the technology needed to realize a micromachine system composing of small-functional elements for conducting diagnosis/cure/repair, movement and independent work in small portions in living organism, disaster site, etc. and a medical-use micromachine system to analyze/react on a trace of liquid. In this fiscal year, the following were carried out: 1) study of micromachine systems, 2) study of a medical-use micromachine system to analyze/react on a trace liquid, and 3) comprehensive investigational study. In 1), studies were made toward the minuteness and improvement of micro laser catheter and micro tactile sensor catheter as functional devices which become the main components of micro catheter for cerebrovascular diagnosis/therapy use and toward the minuteness and improvement of disaster relief use micromachine system. In 2), study was made of element technology of a micro-machine system having functions of sampling/analysis/reaction of a trace of liquid. (NEDO)

  14. Report of the researcher exchange promotion project on the environmental issues in the Asia-Pacific region; Asia/Taiheiyo chiiki kankyo mondai kenkyusha koryu sokushin jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Proposals have been made for the establishment of a network (ETERNET-APR) linking those involved in the research and development of environmental technology in the Asia-Pacific region in order to limit the environmental impact of industrial activity. By pursuing active exchanges of information and personnel, researchers in environmental technology in the Asia-Pacific region have been making serious efforts to establish such a network. This fiscal year, the Internet Web site of the ETERNET-APR has been created using the data collected to date. This database includes information on some 350 researchers and 200 research projects from seven countries. The first international symposium was successfully held at Environmental Research Institute of Chulalongkorn University in Thailand (ERIC), hosting 200 environmental researchers from 10 countries in the Asia-Pacific region. Tripartite sister laboratories ties among the National Institute for Resources and Environment (NIRE) and three Korean laboratories were forged. The sister laboratory project between ICETT and ERIC is also proving effective. These successes prove that intraregional joint research, the objective of ETERNET-APR, has begun to take shape in this year

  15. FY 1999 report on the survey of the international joint research project on medical welfare equipment; 1999 nendo iryo fukushi kiki kokusai kyodo kenkyu jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of internationally cooperating in the R and D of medical welfare equipment, visits were paid to Australia and the U.S. to survey the related administration/research institutes/medical welfare facilities. Australia is a world leader of heart (transplant) operation, organ transplant, artificial middle ear, apneic relaxation equipment, ophthalmological equipment, bio-materials, etc. The country wants to positively promote the international cooperation with Japan because both countries are complementary to each other. Starting about 1999, the U.S. entered the age of competition of the R and D with the use of genome, and the post-genome age is already beginning there. A number of ventures are running for creation of new industry. As to the U.S. government's measures taken for subsidy, regulation, etc. toward new industry, the information could be obtained from the persons concerned. The impression of a tour of welfare facilities in the U.S. was that hardware/software are systematically prepared there, and the aged live bright and positive lives and enjoy lives. (NEDO)

  16. Evaluation report on the development of an advanced refrigerant for compression heat pumps; Asshukushiki heat pump yo shinki reibai kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The research and development were reported on new refrigerants for compression type heat pumps. From 64 kinds of newly composed ether, CF3CF2OCH3 was developed as candidate compound substituting for CFC-11, and CF3CF2CF2OCH3 and (CF3)2CFOCH3 as those substituting for CFC-11. However, COP of the refrigeration has not been optimized. Global warming potentials were obtained by high-accuracy estimate guidelines. The new refrigerants have no chlorine and therefore no effects on the ozonosphere. Global warming effects also satisfied the present allowable values. There was no problem on human body toxicity in the short-term experiment. Costs of commercially production of the candidate compounds were trially calculated from reaction paths and chemical constitution formulae. Assuming that the raw materials are circulating on the market, plant/equipment investment, production volume, and production cost became 5 billion yen, 1000 tons/year, and 3500-6500 yen/kg in 3 persons/shift and 4 shifts, respectively. This is close to the allowable level which is ten times the CFC-12 price, 5000 yen/KG. The new refrigerants are expected to be fully commercialized in consideration of progress of the composition method and improvement of physical properties in the future. 115 refs., 37 figs., 102 tabs.

  17. Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (total system); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Total system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    For every solar energy utilization field, its background, feasibility, impact in practical use, and R and D policy in Japan were studied. Heating and hot water supply by solar energy are already practical because of less technical problems and reasonable profitability, and cooling is also practical as far as a technical viewpoint. At present, the technical level of solar heat power generation is in the stage of basic technology, however, in the future, development of economically reasonable systems will be demanded as well as establishment of its technology. The most difficult problem for realizing practical solar cell power generation systems is cost reduction. It is also another problem that a big demand of Si for solar cells further exceeds the current yield of Si in a semiconductor industry. A small-scale hybrid solar cell power generation system applicable to the roof of general residences is already feasible. Although a solar furnace is still poor in application to industrial fields, it is expected as the leading part for a future solar heat chemical industry. (NEDO)

  18. Report on investigation new energy vision establishment in Zao Town area in fiscal 2000; 2000 nendo Zaocho chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established in the Zao Town area in Miyagi Prefecture. The population of Zao Town is 14,240 persons as of 2000, continuing the slow decreasing trend since 1986. The energy consumption is accounted for by the industrial department at about 50% of the total consumption, followed by the transportation department at about 30%, and the consumer department at about 20%. Discussions on the new energy utilization possibility revealed 30,905 MWh annually by photovoltaic power generation, and 34,630Gcal annually by solar heat utilization. Discussions were also given on power wind generation, small to medium hydropower generation, utilization of hot spring heat, and others. The new energy introducing project includes introduction of photovoltaic power generation into such public facilities as the public hall and athletic park, private sector operated houses and business facilities, introduction of wind power generation into the surrounding areas of the Zao Heart Land and skiing areas, snow melting utilizing hot spring heat, conversion of the automobiles used in the official organizations into clean energy fueled automobiles, installation of bio-mass plants, illumination of parks and streets utilizing photovoltaic and wind power generation systems, and micro hydropower generation in small to medium size rivers. (NEDO)

  19. Report on the FY 1999 R and D survey on ultra-high sensitive photoelectric converter; 1999 nendo chokokando koden henkan soshi ni kansuru kenkyu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the ICB method which is one of the ion engineering methods, photomultipliers were formed using organic dye thin films. By changing the energy to bond traps on thin film/metal electrode interface and electric charges by change of acceleration energy of ion beams, a technology was developed for adjusting the optimum operating temperature between -20 degrees C and +100 degrees C. The wide range of operating temperature and favorable SN ratio can be realized. It was made clear that the dark current of the photomultiplier is composed of two components of contribution by the residual charge stored on the interface at photomultiplying and of contribution by charge injection from the Schottky barrier. Based on this, the residual electric charge removal method by heating and applied pulse voltage was developed. The development for practical use was studied of ultra-high sensitive photoelectric converters. As an intelligent photo sensor, a biomimetic visual photosensor was proposed which uses amplification/memory/arithmetic functions and film formation/processability of organic thin films. The paper also described the image sensor. (NEDO)

  20. Report on the geothermal development promotion survey. No.34. Kaminoyu/Santai area; Chinetsu kaihatsu sokushin chosa hokokusho. No. 34 Kaminoyu Santai chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper summed up the results of the geothermal development promotion survey 'Kaminoyu/Santai area' which was carried out at Yakumo town, Yamakoshi county, and Mori town, Kayabe county, Hokkaido, from FY 1990 to FY 1992. In the survey, the following were conducted for the comprehensive analysis: surface survey such as geology/alteration zone survey, geochemical survey and gravity exploration, test to induce jetting of geothermal fluids by drilling 7 boreholes, temperature/pressure log, etc. The geological structure of this area is featured by the uplift structure/caldera structure and the anticline structure. In the wide-area geothermal system, it is thought that the low-temperature seawater permeates underground by mixture with meteoric water, is heated, and forms the deep geothermal water. It is thought that the hot spring water in this area is stored in the hot spring reservoir by mixture with the surface water, and it is gushing. In the area, the region which is regarded as favorable as passage/storage place of geothermal fluid is a region of 1.5km width extending linearly in the E-W direction from the Nigorikawa basin to Kaminoyu. Further, it is thought that fractures were unfavorably developed in the Santai/Kaminoyu area. (NEDO)

  1. Report on the FY 1999 project for training coal engineers. Advanced course; 1999 nendo sekitan gijutsusha yosei jigyo hokokusho. Jokyusha course

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    This is a report on the training for coal technology which two Japanese engineers received in Australia. In Chapter 3 (Outline of Australia), they studied the national land, constitution of the national land, population, history, politics, economy and trade. In Chapter 4 (Coal geology), they read lecture data of university. In Chapter 5 (Outline of coal supply/demand), the coal export amount from Australia is 167 million tons. Steam coal of a little less than 50% is exported to Japan. In Chapter 6 (Coal mining technology), 100 million tons of NSW state and 100 million and 570 thousand tons of QLD state are mined by underground mining and open pit mining. Training was conducted on overburden/drilling/transportation of the open pit mining coal. As coal mining methods of underground mining, they learned the board and pillar coal mining and high wall mining as an extension of open pit mining. In Chapter 7 (Coal preparation), they observed/studied the jig, heavy media separator, heavy media cyclone separator, flotation equipment, spiral ore dressing equipment, fine powder centrifugal dewatering equipment, thickener, sieve, etc. They studied by data or by observation in Chapters 8 (Outline of coal mine), 9 (Outline of export port), 10 (Outline of railroad transportation), and 11 (Quality management). (NEDO)

  2. Achievement report for fiscal 1998. Research and development of advanced functional materials designing platform; 1998 nendo kokino zairyo sekkei platform no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Stated in this paper are the reports of the working groups (WGs) for the above-named endeavor and the reports on the achievements of the universities to whom the jobs had been commissioned. WG1 carried out research and development related to the coarse-grained molecular dynamics method. WG2 dealt with mesoscale structures, which are quite larger than atoms, such the phase separated structure of polymer molecules and interfacial structures, worked for the construction of a general-purpose simulator system for reproducing/predicting their dynamic properties, and studied the properties of polymers by use of the said simulator system. WG3 worked on polymeric phenomena large in scale in terms of both space and time. Faculty of Engineering, Yamagata University, constructed a materials physical property database necessary in designing materials by simulation. Institute of Industrial Science, Tokyo University, studied the viscoelastic phase isolation at the quantitative level. Tokyo University's Faculty of Engineering-managed study teams investigated the nano-scale structures and properties of polymer materials. Faculty of Engineering, Tokyo Institute of Technology, performed research and development about the meso-scale behavior of multi-constituent polymers. (NEDO)

  3. Fiscal 1997 survey report on international cooperation for the energy use rationalization method; 1997 nendo jigyo hokokusho (energy shiyo gorika shuho kokusai kyoryoku chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To carry out LCA in ISO-14040, inventory analysis (IA) is the basic. For studying arrangement of public data to carry out IA, collection work was done of background data which are indirectly concerned with copying machine. First, methods to make inventory data (ID) which are thinkable in the present situation were prepared, and items of emitted matters to be collected were set up in relation to the impact assessment method. Secondly, scenarios of each stage of life cycle of copying machine were set up, and virtual data on the material/energy consumption amount were arranged. Based on this, a method was further studied for making ID of the parts used in electric power, iron/steel, plastics, and copying machine. Third, based on the above-mentioned study results, ID was actually made, and a possibility was studied of making inventory in life cycle of copying machine. Moreover, the state of the automobile LCA carried out at Stuttgart University was examined. At last, the paper summed up subjects of and future study methods for the inventory making method. 2 refs., 25 figs., 77 tabs.

  4. Research report for fiscal 1998. Research into the recycling of plastic wastes into resources; 1998 nendo hai plastic no saishigenka ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The actualities in Japan are investigated of the types and quantities of plastic wastes, collection and recovery systems, and recycling technologies. Plastic wastes exceeded 9-million tons in 1996, of which 39% was effectively utilized while 61% was merely incinerated or used for reclamation. The 61% of the plastic wastes which are equivalent to oil resources in terms of the energy they contain is found dealt with in such ways, for which additional energy has to be consumed. Some problems are mentioned that occur in the CO2 gas reduction effort in the process of plastic waste recycling for each of its stages of production, distribution, assortment, recovery, and reuse. The problems involve the required reform into production designs and systems with the greatest importance attached to recyclability; share of the expenses between the producing and distributing parties and financial support to assortment/recovery systems; reform of consciousness of both people at large and the administrative organizations, mutual collaboration between them, and reasonable share of expenses between them; construction of a unified assortment/recovery system; expansion of the scope of use of recycled products and the building of environments that encourage their use; diversification of recycling methods and establishment of technologies therefor; and limits on the use of materials and products that generate heavy impacts on environments during their life cycles. (NEDO)

  5. Report on survey in fiscal 1998 for preservation of Jozankei Spa (second report); 1998 nendo Jouzankei onsen hozen chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    This paper describes the report on the survey in fiscal 1998 for preservation of Jozankei Spa (the second report). The hot spring area is located on the periphery of relative elevation area on the western side of a fault growing on the boundary of dikes constituting the lower part of the Jozankei quartz porphyry, with the fault forming a boundary. The fault peripheral beds have cracks develop nearly parallel to the fault. The low specific resistance anomaly extracted at underground depth from 100 to 500 m in the area south of the hot spring gushing area forms the clay alteration zone around the hot spring water and cracks arising from the opening type cracks formed around the weak lines of dikes, faults, and surface of unconformity. The hot spring originated water having risen and passed through fractures from deep underground section stagnates in these crack groups, and forms hot spring aquifer. The water is considered to have such nature as temperature of 120 degrees C, chlorine at 1,600 mg/l and tritium concentration of 2.1 to 2.5 TU. The water is characterized by eluation constituents from the Usubetsu bed. The hot spring water in the aquifer rises passing through the opening cracks in the upper part, wherein the water not mixing with ground water does not have the constituents change, and the mixed water changes the nature of the hot spring water. In the surface layer, the water flows through intersecting joints growing around the fracture, and gushes out of the ground. (NEDO)

  6. Fiscal 1997 report on the results of the international standardization R and D. Robot control system; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Robot seigyo system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    R and D of the robot control system was conducted in the following items: 1) integrated open control system, 2) remote control robot manipulation language, 3) human factor robot use built-in LAN system, 4) built-in actuator driver. In 1), there were some problems to be pointed out around the system, but the effectiveness was confirmed as system architecture of each verification item. In 2), development/design were made of RCML(R-Cube Manipulation Language) as a remote robot manipulation language, telecommunication protocol, and the experimental system, and the international standardization was targeted. In 3), the R and D was conducted of the realtime telecommunication protocol which clears the standards for the distributed control required for construction of human factor robot and the advanced realtime micro-controller, ULSI, which is the one that the protocol was made IC. In 4), an intelligent connector for built-in actuator was developed which enables saving of wiring in robot system and plug-in connection. 13 refs., 186 figs., 53 tabs.

  7. Report on a survey in fiscal 1999. Survey on energy use evaluation systems; 1999 nendo energy shiyo hyoka system chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The present survey and study relate to the medium to long term policies for technological development of energy and environment related technologies, and are intended to develop a system that can evaluate the importance, feasibility, expected realization time, and expected cost of the technologies, including their synergetic effects. The survey and study are intended to provide clear guidelines for planning the technological development policies on which of the technological development should be promoted in what ways, based on the evaluation given by the use of the system. The report describes in Section 1 to adopt two types of approaches of a 'technology map' and a 'network chart evaluation system' to achieve the goal. Section 2, after describing the results of surveys on the past study cases of technology evaluation, describes that the present approach has new features that are different from conventional ones. Section 3 states the results of surveys on the basic technologies to prevent global warming, and shows cases of preparing maps that notice on energy flows. Section 4 relates to network chart evaluating methods. Section 5 describes the results of surveys that have been made in relation with chronological progress of the technological development, in preparation for surveys to be made in the coming fiscal years. (NEDO)

  8. Initial-stage research report on business of drawing up regional new energy vision for Shibecha Town; Shibechacho shin energy vision sakutei jigyo chosa shoki dankai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The vision includes (1) the buildup of foundations for comfortable living circumstances by utilizing new energy, (2) the development of local industries that befriend themselves with nature by utilizing new energy, and (3) the practice of education and training on environment through the intermediary of new energy. Concerning item (1), in the construction of public facilities, residential houses, and roads, all of which constitute the foundations of daily life, plans will be promoted to use energy produced by the utilization of natural energy resources such as solar rays, solar heat, and wind force, and other energy produced by utilizing heat from refuse incineration and heat latent in the sewage, for the establishment of comfortable living conditions with CO2 emissions reduced. Concerning item (2), studies will be made to install biogas-utilizing plants for excrement treatment and recycling in dairy and animal husbandry; and wind power generation and small-scale hydroelectric power generation will be introduced for supplying power in connection with the effort to complete programs for constructing resort country sites and public meadows. Concerning item (3), for the development of the eco-museum concept, new energy facilities utilizing solar rays, solar heat, wind force, etc., will be introduced into school buildings. (NEDO)

  9. Research report for fiscal 1998. Study of utilization of biomass including foods in energy industry; 1998 nendo shokubutsu nado no biomass no energy riyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Rice being produced as food is taken up out of various types of biomass, and a feasibility study from the viewpoints of technology and economy is conducted as to its use in the energy industry. The production of ethanol from rice, though it has no past record worth discussion, is similar to the production of ethanol from other biomass resources in terms of technology and economy. The problem is that the production cost of rice is far higher than those of other materials. It is expected, however, that there will a large-scale production cost reduction and an increase in the yield when novel cultivation techniques are introduced in the future. It is also expected that alcohol from rice will be sufficiently competitive with alcohol from molasses or the like when the exploitation of cellulose-family by-products such as husks becomes feasible. The study on this occasion deals solely with the effective use of farmland and the surplus rice. A confrontation between rice as a biomass resource and rice as a food has to be avoided as much as possible in the long term because it may cause a price rise and compromise the security of food supply. That is, in discussing this matter, it is mandatory to draw a very definite line between rice as a food and rice as an alcohol production material. (NEDO)

  10. Fiscal 1992 report. Overseas surveys out of surveys for coal hydrogasification technology development; 1992 nendo sekitan suiten gaska gijutsu kaihatsu chosa ni okeru kaigai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-12-01

    As part of the coal hydrogasification technology development survey project, overseas surveys were carried out as in the preceding fiscal year. With an emphasis placed on the process materials and resources, and on product utilization technologies, surveys and studies were conducted about the trends of development of coal and natural gas resources, and information was collected on energy-related matters in Indonesia and Australia. The need of hydrogasification technology was investigated from the viewpoint of natural resources. Moreover, Japanese engineers were dispatched to APEC (Asia-Pacific Economic Cooperation Conference) New Energy Seminar, Indonesia. Visits were made for information on the natural gas resources at an LNG base in East Kalimantan, Indonesia; coal gasification, energy, and others at CSIRO (Commonwealth Scientific and Industrial Research Organization), Australia; coal bed and methane resources at Warren Center, University of Sydney, Australia; coal bed and methane resources at the Brisbane office, Mitsubishi Gas Chemical Company, Inc.; and coal resources at coal mines of Idemitsu South Queensland Coal Pty Ltd. (NEDO)

  11. Fiscal 1998 'Plant Biotechnology in the 21st Century' workshop report; '21 seiki no shokubutsu biotechnology' workshop 1998 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The workshop was opened with the opening remarks by Yamada (President of Nara Institute of Science and Technology (NIST)), the overview of plant biotechnology in the 21st century from academia by Shinmyo (Professor of NIST), and the overview of such technology from Ministry of International Trade and Industry by Katao (Chief of Chemical Industry Division). Lectures and discussions of various topics were conducted for 2 days as follows. The effectiveness of a genomic DNA array method for obtaining the genes for switching genes according to daytime, nighttime, drying, salt, high temperature and low temperature for every plant. Current transfer technology of large DNA fragments into plant cell nuclei and chloroplast. Biological evaluation of the physiological functions and complex stress tolerance capacity transformed by transferring complex stress tolerance genes and useful genes for productivity improvement and value addition. Discussion was also held on the importance of a basic research for biotechnology in the 21st century. (NEDO)

  12. Report on current status of petroleum substituting energy development in the EU in FY 1997; 1997 nendo chosa hokokusho (sekiyu daitai energy kaihatsu no genjo (EU))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The EU is one of the most advanced places of petroleum substituting energy development. The EU is highly aware of environmental issues. For the COP3 held at Kyoto in December 1997, The EU gave more severe regulation of CO2 emission than the other advanced countries. The EU takes efforts in the development and introduction of energy effective for global environmental protection. In addition, research and development of geothermal, biomass and wave force energy are actively promoted in this place. Energy situations in this place are significant for predicting and analyzing the future trends of energy development and consumption in the other countries. Firstly, this report looks back toward energy demand held in check to a head at the beginning of the 1990`s. Secondly, supply of energy and cover of energy trend are described for recent years from the point of view. Thirdly, competitiveness of energy in EU countries are discussed from a position of energy density. Fourthly, circumstances about environmental issues are considered. Fifthly, the world market of energy is also considered. Finally, development of new energy and a trend of introduction with a sample of Sweden are introduced. 13 refs., 15 figs., 28 tabs.

  13. Regional new energy vision for Kakegawa City. Formulation survey report; 2001 nendo Kakegawa shi chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for enhancing people's consciousness of such at Kakegawa City, Shizuoka Prefecture, surveys and studies were conducted involving the energy demand of the city, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The city consumes approximately 11,638 GJ/year, with the industrial sector consuming 4,896 GJ, the residential/commercial sector 3,608 GJ, and the transportation sector 3,134 GJ. Energy types are electric power, gas oil, heavy oil, gasoline, kerosene, LPG, and town gas, as listed in the descending order in terms of consumption rate. The amount of carbon dioxide resulting from the consumption is estimated at 673,214 t-CO2. Projects for new energy introduction were studied, which involved photovoltaic power generation for the general-purpose gymnasium, kindergartens, the school meal center, and meeting places; introduction of solar heat utilization systems into public facilities; financial support system for the purchase of solar heat utilization apparatuses; refuse-fueled power generation and heat utilization at a new cleaning center; utilization of biogas from garbage and stock raising waste; utilization of woody resources; clean-energy vehicles; and so on. (NEDO)

  14. Regional new energy vision formulation project for Ukiha Town. Fiscal 2001 report; 2001 nendo Ukiha machi chiiki shin energy vision sakutei tou jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for enhancing people's consciousness of such in Ukiha Town, Fukuoka Prefecture, surveys and studies were conducted involving the amount of energy needed by the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The energy consumption of the town is estimated at 158,886 drums/year in terms of crude oil - 56.2% in electric power, 19.5% in gasoline, 10.5% in gas oil, 6.9% in kerosene, 4.2% in fuel oil A, and so forth. Projects for introducing new energies were studied, which included the introduction of photovoltaic power systems into public facilities, gymnastic halls, and comprehensive welfare centers; introduction of a large wind power system (1,500 kW) in the vicinity of the Michinoeki roadside service spot; installation of a power plant fueled by woody biomass (scrap wood, saw dust, and the like); introduction of clean energy vehicles for official use; installation of photovoltaic/wind hybrid power-lighted street lamps in the shopping area; installation of light traps for agriculture burned by photovoltaic power; and financial aids for encouraging the installation of photovoltaic power generation systems in general residences. (NEDO)

  15. Regional new energy vision formulation for Kadogawa Town, Miyazaki Prefecture. Report; 2001 nendo Miyagi ken Kadokawa cho chiiki shin energy vision sakutei tou jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for elevating people's consciousness of such in Kadogawa Town, Miyazaki Prefecture, surveys and studies were conducted concerning the energy demand in the town, the amount of new energy resources in existence, and new energy introduction plans, and then a vision was formulated. The town's energy demand is estimated to be 1,197.4-million MJ/year, which includes 44.1% for the transportation sector, 22.9 for the residential sector, 22.7% for the industrial sector, and 10.3% for the people's livelihood-related business sector. The energy demand is covered 62.7% by oil-based fuels, 22.7% by electric power, and 13.4% by LP gas. Projects discussed for new energy introduction included the introduction of photovoltaic power into the town office, primary schools, and a comprehensive workers' welfare center; introduction of a solar hot water supply system and hybrid power-lighted street light into a seaside park; introduction wind power into Motoyama Park; mini-scale hydroelectric power on the Isuzu river; introduction of clean energy vehicles into the town office; power generation fueled by methane gas from livestock excrement; and introduction of natural gas fueled cogeneration into a resort house. (NEDO)

  16. Regional new energy vision formulation survey for Ochi Town. Report; 2001 nendo Ouchi cho chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for elevating people's consciousness of such in Ochi Town, Saga Prefecture, surveys and studies were conducted involving the amount of energy needed by the town, the amount of new energy resources in existence, and new energy introduction programs, and a vision was formulated. The demand for energy of the town is estimated at 613,575 times 10{sup 9} J, with the industrial sector responsible for 47.7%, the transportation sector for 26.6%, and the residential and commercial sector for 25.7%. Electric power, heavy oil, gas oil, gasoline, and kerosene are demanded, named in the descending order in terms of magnitude of demand. Key projects were discussed for new energy introduction, which included the introduction of photovoltaic power into a culture exchange center; nighttime illumination of Mikaeri Waterfall by micro-scale hydroelectric power; installation of a water purification system for the Ikisa Dam using photovoltaic power and micro-scale hydroelectric power; introduction of photovoltaic power into a comprehensive sports park and the Ochi Junior High School; and large-scale agricultural production and processing plant operation using photovoltaic power. (NEDO)

  17. Achievement report for fiscal 1998. Development of environmentally friendly universal controller; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances. An environmentally friendly UC is a remote controller which utilizes an infrared two-way communication function and becomes capable of dealing with any appliance upon downloading remote control information from the appliance involved. Studies were conducted for the development of controller hardware and software therefor and for the development of electrical home appliances to correspond to their specifications. In relation with energy conservation, studies centered about reduction in power consumption while on standby and unnecessary power consumption. As the result, an environmentally friendly UC protocol was newly developed and, based on the protocol, plural numbers of controllers, appliances, and network gateways were tentatively fabricated, and were examined for their function, behavior, and operational interchangeability. Systems aiming at reducing power consumption while on standby and unnecessary power consumption were built by way of experiment, and were checked for performance. It was then concluded that a reduction of several billion kWh might be achieved. (NEDO)

  18. Report on the fiscal 1996 development of high efficient waste power generation technology; 1996 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The technical development was made by which high-temperature/high-pressure steam is generated in the incineration furnace using general waste, combustible industrial waste, etc. as fuel to generate power high efficiently, and reliability of the superheater, etc. was verified by the pilot plant. For it, the following were conducted: development of element technology (high-temperature/high-efficiency combustion furnace, corrosion resistant super heater materials, environmental load reduction technology) and the demonstration (demonstrative test in pilot plant, study of an optimum total system). In relation to the external circulation type fluidized bed furnace, reformation was made which enables simultaneous sampling of dioxins, etc. The combustion test was done using the reformed combustion testing furnace to obtain the data necessary for the study of formation/decomposition mechanism of dioxin. The amount of corrosion reduction of superheater sample material for pilot plant use was determined. A study was made of improvement of removal of dioxins and NOx in the pulse plasma exhaust gas treatment method. The pilot plant was installed. 10 refs., 205 figs., 79 tabs.

  19. FY 1997 survey report on information sharing product life-cycle systems. 2; 1997 nendo joho kyoyugata product life cycle system ni kansuru chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Highly value-added products considering a total life-cycle of products by integrating both production and consumption activities are much in demand, and each information corresponding to each product should be realized by concept integrating both information and product as common element. Survey was made on what a social system integrating production and consumption should be, a product information model, and technology integrating both information and product for raw material, industrial machine and household appliance as examples. An information model shared by the whole production and consumption activities was first prepared. Based on this model, data storage, update, retrieval and dispatch technologies were surveyed and developed for life-cycle systems. Degradation and life sensing technology was surveyed for maintenance, repair and disposal activities using proper unstable information of each product. A support system for use of shared information was developed to promote a new highly value-added function. Total evaluation was made on information sharing product life-cycle systems. 10 refs., 23 figs., 7 tabs.

  20. Fiscal 1998 research report on development, study and evaluation of tribo-materials; 1998 nendo tribo material no kaihatsu chosa hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Recently, needs for tribo-materials are on the increase for further energy saving and improvement of various functions and durability in various field such as less-fuel consumption car, new type Shinkansen, linear motor car, high-speed motor boat, various machines and tools, electronics, medical equipment and vitally adaptable material. This project researches and studies various properties required for tribo- materials for surface treated materials by ceramic and other material films, and clarifies the guidance and direction of the technology for creating tribo-materials by surface treatment and surface modification, through clarifying a friction/abrasion mechanism by collection of basic characteristic data and analysis of abrasion powders. This project is studying the marginal condition of film destruction for ceramic system vapor-phase deposited films, through studying the effect of mechanical properties of substrates, film surface treatment methods and film surface shapes on the marginal condition. (NEDO)

  1. Research and development on fusion zones in fiscal 1999. Third volume. Biomolecular mechanism and design; 1999 nendo yugo ryoiki kenkyu kaihatsu seika hokokusho. 3. Biomolecular mechanism and design

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    It was intended to elucidate the structures of living organisms having excellent functions and the principles of these functions, and to create cells, structural bodies and molecular mechanisms that substitute these functions outside the bodies of the living organisms. Therefore, research and development has been performed on the fundamental technologies, whose achievements are compiled. In the research of creating cultured bones and cartilages, marrow cells and cartilage cells were cultured while providing physiological active materials and mechanical stimulation. Porous ceramics and porous biodegradating polymers coated with collagen were used as the substrate materials to have created artificial cartilages. In the research of structural change in a molecule motor, a low temperature electron microscope was used to make the structure visualized successfully for the first time. In the research of creating an artificial liver, the world's first cells like stem cells separated and refined from liver cells were cultured three dimensionally in a bio-reactor using special cultivation solution to have established the basic technology. In the research of libozyme, sensor function and high catalytic function were realized successfully in the cells by dimerizing libozymes. (NEDO)

  2. Report on the geothermal development promotion survey. No.36. Mt. Amemasudake area; Chinetsu kaihatsu sokushin chosa hokokusho. No. 36 Amemasudake chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper summed up the results of the geothermal development promotion survey 'Mt. Amemasudake area' which was carried out at Akaigawa village, Yoichi county, Hokkaido, from FY 1991 to FY 1994. In the survey, the following were conducted for the comprehensive analysis: surface survey such as geology/alteration zone survey, geochemical survey, gravity exploration, electromagnetic exploration and electric exploration, core test by drilling 5 boreholes, test to induce jetting of geothermal fluids, measurement of in-borehole temperature/pressure, survey of geochemical properties of geothermal water. As to the fracture system in this area, the Amemasudake fault and the Amemasuzawa fault are especially important, and it was assumed that these faults had relation to the present geothermal distribution. It is thought that structural conditions of geothermal reservoirs are fractures in basement rocks. As a result of the borehole survey, it was indicated that the center of the high-temperature part with a temperature of 250 degrees C or more was in the boundary zone southeast of this area at a level of 500m below sea level. The scale, which reached about 3km both in east/west and north/south, is almost the same scale as that of the neighboring Toyoha area where great potentiality of the geothermal development is expected. (NEDO)

  3. Fiscal 1998 report on international joint research project for preventing global warming; 1998 nendo chikyu ondanka boshi kokusai kyodo kenkyu jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    Japanese researchers were dispatched to research institutes abroad for conducting joint studies on nine subjects for which such efforts would work effectively. The researchers were sent to various research institutes in the U.S., Britain, Germany, and others. The nine subjects were (1) the application of the most up-to-date welding and bonding technologies to liquid hydrogen storage/transportation containers, (2) development of low-temperature high-activity metal catalysts for energy conservation processes, (3) study of CO2 emission behavior using a large-scale simulator of deep sea circumstances, (4) study of condensation control for steam and chemical species in the global atmosphere, (5) numerical analysis of semiconductor crystal growth for ultralow loss power device, (6) development of sulfur-rich hydrocarbon gasification technology using a metal melting furnace, (7) assessment of techniques for evaluating origins of environmental pollution gas, geothermal gas, and soil gas using multiple isotopes, (8) analysis of behavior of the steam circulation type turbine system, and (9) the embodiment of a large premixed compression ignition engine. (NEDO)

  4. Report on fiscal 1998 results. Item of development, 'research on technologies for disaster prediction'; Saigai yochi gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Development was conducted, with the results summarized, for an electromagnetic probing system using a superconducting quantum interference device (SQUID) sensor, for the purpose of establishing disaster prediction technologies by grasping the underground structure highly precisely and three-dimensionally. The developed electromagnetic probing system consists of SQUID elements, 3-axial probe with driving circuits, liquid nitrogen Dewars, automatic control circuit of SQUID biases, high speed multi-channel A/D converter, mobile computer and a battery unit. The software has the function of SQUID bias control, measurement, data saving and data analysis. For the electromagnetic probing analytical program, an one- and three-dimensional interpretation programs were developed. As a result of the field tests, the subject system proved to be strong against city noise and advantageous for fault investigation in urban areas. In addition, being a sensor of multi-component/differential measurement, the system is also supposed to be useful in mine surveying. (NEDO)

  5. Report on the results of `the R and D of industrial technology information base arrangement`; `Sangyo gijutsu joho kiban seibi kenkyu kaihatsu` seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In relation to information processing in the open type research information networking, R and D were conducted to establish basic technologies such as grading-up, acceleration, enhancement of efficiency, diversification of application, promotion of usable data accumulation, etc. As to the R and D of software to promote sharing of research information, software was developed which can easily modify and renew management objects for users at research sites, etc., and the target was almost achieved. Concerning the R and D of information supply technology, an approach was presented whereby clients submit bids for each stream of the data requested and the admission decision is made so as to maximize gain of the session under network capacity constraints. Additionally, the R and D were made of software to construct an international information sharing system, a system for multi-lingual I/O, text manipulation and communication, and software for remote use of network based information for scientific computing. 138 refs., 125 figs., 33 tabs.

  6. Report on an industrial machinery engineering policy study meeting. Studies on new energy industries; Sangyo kikai engineering seisaku kenkyukai (shin energy sangyo no kenkyu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-07-01

    Effects extended to industrial areas by new energy development were analyzed by using the industrial relation table. Technological development of new energies can mass-produce energy without being restricted by energy resource availability, and retaining manufacturing facilities can exhibit energy reserve function with security. The technologies may be suitable for local energy supply. In the aspects of industrial policies and people's living, demands on diversification and improvement of the people's living may be responded, levels of scientific technologies may be enhanced, and contribution to improving the industrial structure may be expected. The energy industry includes a large number of related industries and has vast related areas. A large number of technology induced effects can be expected in the course of research and development. A market of huge size may be estimated in the future, by which level elevation of the industrial structure would be supported. Early promotion of the new energy development is an urgent assignment for the 1980's. In order to achieve this goal, it is necessary to promote research and development, proliferation and practical application, for which the physical strength of the present Japan must be utilized to its maximum in making human and fund investments. Expansion and improvement in the industrialization infrastructures are also important, whereas the government's subsidies must be increased, and vitality in the private sector must be incorporated into organized force. (NEDO)

  7. Fiscal 2000 survey report on R and D results of advanced clean energy vehicle; 2000 nendo kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With problems inherent to clean energy vehicles such as cruising distance, fuel supply and fuel consumption, ACEVs (advanced clean energy vehicles) are in demand featuring both low pollution and high efficiency compatibly. This paper explains the fiscal 2000 results of development. The target is, by using oil-alternative fuel, to reduce driving energy consumption and carbon dioxide emission to less than half and to control the life cycle cost (total of manufacturing cost, operating cost, fuel cost, etc.) to not more than twice as much as those of conventional vehicles. As ACEVs, an ANG (adsorbed natural gas) engine and flywheel battery mounted passenger car was selected, as were a CNG ceramics engine and capacitor mounted truck, CNG engine and lithium-ion battery mounted truck, LNG engine and capacitor mounted bus, and a DME engine and capacitor mounted bus. All are hybrid systems with an energy saving device. In the research of synthetic fuels, the results of the studies were summarized including the effect of various synthetic light oils on engine performance, fuel characteristics, effect of PM grain size and the optimum properties. (NEDO)

  8. Final report on the survey to verify a new method for power load leveling; Fuka heijunka shinshuho jissho chosa saishu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The purpose of this verification survey is to verify the effectiveness of a system using capacitor for power load leveling and output leveling in the photovoltaic power generation. For the former, the charge is conducted in the nighttime, and the discharge in load peak time in the daytime. The capacity required is small for the output, and therefore, there is a viability of capacitor. For the latter, abrupt output variations by solar cells are leveled by storage device using capacitor. Since the output variation generated in a short time by solar cells requires responsibility and life in case of abrupt charge/discharge, it is suitable to use capacitor. The demonstration use capacitor is an organic stacking type for the former, and an organic jelly-role type for the latter. As a result of the demonstration, for the former, a power storage system which has 32-module series/parallel connection bank switch type + 2-way ac/dc exchanger was made and operated for verification. The overall efficiency of 85% was obtained. For the latter, a system which has 2,400F x 70 series bank, 6,000F x 70 series bank x 3 parallel bank and 3kW solar cells was operated for verification. Much effect of output leveling was confirmed. (NEDO)

  9. FY 2000 report on information exchanges/analytical survey for improvement of energy consumption efficiency; 2000 nendo energy shohi koritsuka joho kokan bunseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of surveying the situation of the arrangement of methods of energy conservation promotion and the emissions trading system in developing countries by Japan having the effectiveness or in cooperation with developed countries, information was collected through the participation in international conferences related to energy conservation promotion, etc. and by visits at governmental organizations in charge in developed countries and developing countries. The results of the survey were classified into the following four items: 1) survey method; 2) exchanges of information on energy conservation in main 3 developing counties; 3) exchanges of information of energy conservation in the main developed countries; 4) exchanges of information of the emissions trading system (international trading system of energy conservation values (greenhouse effect gas emission right)). In 4), survey was made on the following: the emissions trading system for the inside of company group (BP-Amoco), the details of the emissions trading system for one country (the U.K.), the grapple with the emissions trading by a private trading organization (NATSOURCE Co.), and the handle with the emissions trading system by each of the OECD countries. (NEDO)

  10. FY 1998 report on the results of the project on the next generation structure housing development; 1998 nendo jisedai kozo jutaku kaihatsu jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The purpose of this project is to develop/verify technology to design/construct a structural body of multiple dwelling house which is highly durable and usable at maximum of the limited space with no projections of poles/beams, and is also to develop/verify a composite system of a structure and each house in which residential space can freely be changed horizontally/vertically in response to the leveling-up of living and changes in life style. The following were conducted: construction of an experimental house group with next generation structure; development of technology of effective space utilization/high durability body construction; development of technology of structural analysis/design systematization of antiseismic/damping system; development of commercialization of technology to heighten frame durability, development of technology to heighten durability of finishing materials of a body; development of low cost construction technology; development of technology of interface between a body and each house; verification of housing performance using a next generation body system; generalization of next generation frame system/house system. To reflect the results of the research quickly, the details of the research are systematized, and a draft is worked out of a guide for constructing the next generation frame system/house system which were arranged between the current architecture related laws and business as a general multiple dwelling house. (NEDO)

  11. Leading survey and research report for fiscal 1999. Survey and research on chemical reaction simulator technology; 1999 nendo kagaku hanno simulator gijutsu no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Although various chemical reactions are made use of at scenes of chemical industry for the acquisition of desired chemicals, the control of reaction process governing factors, such as temperature, pressure, catalysts, solutions, etc., is found to be carried out only on the empirical basis. At the present time, rational or optimum reaction designs are not to be prepared in a short period of time in the presence of the widespread shortage of knowledge about chemical reactions and of the shortage of understanding of chemical reactions at the micro level. Leading survey and research are conducted for the development of a 'chemical reaction simulator' technology to enable the acquisition of optimum reaction designing guidelines in a short period of time. Using the simulator, a chemical of his choice is inputted by a researcher engaged in the study of an real chemical reaction and then various techniques of computer science are mobilized for the preparation of a huge number of feasible reaction routes, and high-precision simulations are conducted for the feasible reaction routes. The results achieved this fiscal year are reported. The purpose of this research and its ripple effect on new product industry creation are stated. Then the positioning, mission, and concept of such a chemical reaction simulator are described. Finally, the result of research and survey of knowledge databases and the result of research and survey of computational chemistry are stated. (NEDO)

  12. Achievement report for fiscal 2000 on development of technology to evaluate reliability of petroleum refining facilities; 2000 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper reports the achievements in fiscal 2000 in development of a technology to evaluate reliability of petroleum refining facilities. The development efforts were made mainly on analyses by simulation and neural net (NN) that utilize computers. In the high-temperature system facilities, the creep damage generation is governed by different factors including impurities. The evaluation on joint life requires simultaneous use of low temperature zone long-time test. Verification was made on application of non-destructive inspection, such as use of ultrasonic waves in the accelerated creep zone. Defect detecting capability was identified when an ultrasonic wave flaw detection model is used for buried piping. In the pulse eddy current flaw detection, a coil most superb in totality was selected by means of simulation, by which corrosion and wall thickness of piping and devices were detected from outside the sheathing materials. Development was made on a technology to diagnose and evaluate corrosion of tank in operation by using the AE method. The remaining life of transformers is determined by how seriously the coil insulating paper has been deteriorated, and furfural in the oil was found effective for the parameters. Particularly, application of the NN was revealed to be effective in estimating electric motor deterioration. A high-temperature sulfide corrosion rate estimating model was developed from the operation and measurement data of the facilities by applying the NN and TCBM. (NEDO)

  13. Fiscal 2000 survey report on regional new energy vision formulation for Kawanabe town, Kagoshima Prefecture; 2000 nendo Kawabecho chiiki shin energy vision sakutei nado chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A regional new energy vision has been formulated for Kawanabe town, Kagoshima Prefecture, to be participated in by inhabitants and beneficial to both natural environment protection and inhabitants. The results of the survey are described in six chapter which involve (1) the basic philosophy of vision formulation, (2) outline of new energy, (3) environmental characteristics and townspeople's awareness, (4) energy situation and the amount of new energy existing in Kawanabe town, (5) regional new energy vision for Kawanabe town region, and (6) future tasks. After a study of the existing amount of new energy, energy demand, and people's requests, it is concluded that photovoltaic power generation, wind power generation, hot spring heat utilization, small scale water energy, and refuse-derived energy be the types to be preferably introduced into the town. Projects are established and concrete plans are prepared thereunder, which concern the reinforcement of public relations and enlightening activities, installation of a wind power system as one of enlightening activities, study of Kawanabe town's own subsidy system for encouraging the introduction of photovoltaic power systems and solar heaters for domestic use, and the introduction of photovoltaic power systems into public facilities such as school houses. In conclusion, it is hoped that, since financial difficulties will be a strong factor to impede new energy introduction, the subsidy system will be a solid one. (NEDO)

  14. Report on field test project for wind power development at Nagashima-cho. Detailed wind characteristics survey; Nagashimacho ni okeru furyoku field test jigyo (fukyo seisa) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    A detailed wind characteristics survey was conducted to study the feasibility of a wind power generation system for Nagashima-cho, Izumi-gun, Kagoshima Prefecture. Observation instruments were installed at the top of a hill approximately 80m above the sea level situated to the northwest of the Nagashima-cho town hall and, in the period October 1998 through September 1999, data were collected at a point 20m above ground, such as the average wind speed and direction, wind velocity standard deviation, and the maximum instantaneous wind velocity. The data were analyzed, and findings were obtained, as mentioned below. The annual average wind speed was 5.0m, strong in winter and weak in summer. The annual wind direction occurrence rate was 61.8%, turbulence intensity was 0.17 at wind speeds of 4m/s and more, these not presenting any particular problem. Wind energy density was 148W/m{sup 2}. Both wind speed conditions and energy density were slightly lower than the reference levels indicated for evaluation. Studies were made on the assumption that three classes of wind turbines (150, 300, and 750kW) would be introduced, and then it was found that both operating factors and facility availability rates exceeded the required levels. Since there were no detrimental factors in the surrounding conditions, it was concluded that possibilities were high that wind power generation at the site would be practical. (NEDO)

  15. Survey report for fiscal 1998. Achievement report on research and development of direct methanol fuel cell; 1998 nendo direct methanol nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    Research and development has been performed on a direct methanol fuel cell (DMFC) to generate electric power through direct chemical reaction of methanol not being given modification as a fuel cell to be used for automotive engines. This paper summarizes the achievements in fiscal 1998. In the research of the membranes to conduct ions for the DMFC, an ion conduction membrane which introduces POSS group as the methanol eliminating functional group was prepared to achieve enhancement in tensile strength, heat resistance, and ion conductivity. In the power generation characteristics of the DMFC, verification was given on power generation performance with as high main power density as 0.1 W/cm{sup 2} by using the available electrolytic membranes and electrode catalysts. The characteristics showed effectiveness of the DMFC as the electric power supply source. In addition, fundamental findings were obtained on factors affecting the power generation characteristics of the DMFC as a result of generating power under different conditions. Research and development was given also on the water-methanol-ion exchange polymeric membrane, ion exchange membranes provided with lipophilic and water repellent electrolyte, solid polymeric membranes having high proton conductivity and low methanol permeability, and a new micro-porous filling type polymeric membrane. (NEDO)

  16. Fiscal 1997 report on technological results. R and D on micromachine technology; 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Researches on basic element technology of micromachines are conducted that operate autonomously in a narrow small part in a complicated apparatus or in vivo. The areas of activity are 1. research on micromachine systems and 2. comprehensive investigation and research. In 1, (1) a micro catheter and (2) a micro tactile sensor catheter were studied while, in 2, basic technology and technological problems, particularly those problems concerning sophistication in the medical field were examined and studied. Further, in (1), with the purpose of developing a micro laser catheter for diagnosis/treatment, researches were implemented on the technology of integrating micro laser and an optical fiber which were components of the catheter and on the fabrication of the fine diameter of a micro catheter as well as on the characteristical improvement of the base body on which minute elements were mounted. In (2), characteristical improvement and sophistication were carried out for a high sensitivity contact pressure sensor and a diagnostic tactile sensor, which are mounted on a catheter having a positive bulge control mechanism for insertion into body cavity, with a sensor probe manufactured experimentally. (NEDO)

  17. FY 1989 report on the section meeting of gasification technology of the Coal Gasification Committee; 1989 nendo sekitan gasuka iinkai gasuka gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The paper reported activities of the Coal Gasification Committee in FY 1989. The 1st Coal Gasification Committee Meeting was held on July 21,1989, and report/discussion were made about an outline of the FY 1989 research plan. In the 2nd Meeting, report/discussion were made about activities of each of the section meetings and the progress of the development of coal gasification technology. In FY 1998, as the 4th design/construction of pilot plant, manufacture/installation were conducted of a part (equipment of coal supply system/char recycle system) of the gasification process equipment/facilities. As to recycle gas facilities, manufacture of equipment/facilities was conducted. Concerning a part of the pipe rack/central control panel/electric panel, manufacture/installation of equipment were made. In the support study of a pilot plant (trial development of materials for plant use equipment), refractory was studied in terms of the evaluation of durability of furnace materials against liquefaction residue slag, study of furnace materials responsive to liquefaction residue and gasification of high ash melting point coal, etc. (NEDO)

  18. Report on feasibility study of energy-saving visions for City of Mitaka; Mitaka-shi sho energy vision feasibility study hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    The feasibility study is implemented to concretely promote the project for the (new energy/energy-saving visions for the City of Mitaka area) aimed at abatement of green effect gases which cause global warming, for which the public facilities are investigated to collect information related to the energy-saving project, and the implementation schemes are studied from the operational and fund aspects. A total of 60 public facilities in the city are studied for energy-saving potentials and their characteristics through the questionnaires and simulation, and placed in the order of priority. The project implementation simulation is conducted, to grasp the long-term energy-saving effect, energy cost reduction and CO2 abatement potentials, if the project is actually implemented. The studies on the 10 facilities indicate that power consumption can be possibly reduced by 1.45 million kWh in the initial year, and the accumulated introduction and abatement costs indicate that the project will produce the first profit of around 49 million yen in 2012. CO2 can be abated by 230 tons-C/year on the average during the 2008 to 2012 period. (NEDO)

  19. Fiscal 2000 regional new energy vision formulation. Financially aided project (Report on new energy vision formulation for Nakijin village); 2000 nendo Nakijinson shin energy vision sakutei hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    Nakijin village, Okinawa Prefecture, had a population of 9,500 in 1995 and consumed 1.36 times 10{sup 5} Gcal of energy in fiscal 1998. In its regional new energy vision formulation project, the village has made a decision that it study the introduction of wind power and the like to settle problems relating to energy, environments, and population. In the vision, natural energy utilization and environment preservation are chosen as the targets. The results of related activities are summarized in eight chapters, which are (1) outline of the survey, (2) outline of Nakijin village, (3) new energy in the village, (4) survey of people's awareness, (5) policy toward new energy introduction, (6) projects of new energy introduction, (7) study of models of key projects, and (8) measures for vision enhancement. Established as key projects are the use of clean energy in the village sports park, new energy popularization drive with the integrated junior high school at the center, and efforts to activate local industries and invigorate tourist business. It is planned that a 600 kW class wind turbine be installed in the sports park. (NEDO)

  20. Report on the project for working out the new energy vision of the Iwasaki village area; 2001 nendo Iwasaki mura chiiki shin energy vision sakutei tou jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For the purpose of promoting the introduction of new energy and enhancing the awareness of it at Iwasaki Village, Aomori Prefecture, an investigational study was conducted of the energy demand of the town, existence amount of new energy, introduction of new energy, etc., and a new energy vision was worked out. The population of Iwasaki Village was 2,845 as of October 2000, which decreased approximately 30% in the past 20 years. The energy demand of the whole village was about 280,000 GJ in amount (about 7,202 kL/y in crude oil conversion), consisting of kerosene, light oil, heavy oil, gasoline, electric power and LPG. As viewed by sector, the rate of energy demand in the commercial/residential sector was comparatively high. As the project for new energy introduction, the following were studied: wind power generation around the Yamamori plain/Iwasaki village office; snow melting system using soil heat exchanger on the road in front of elementary school, photovoltaic power generation for public facilities (elementary and junior high schools/house of recreation and relaxation for old people/day nursery)/Tsugaru Semi-national Park/general houses; wave power generation at the Iwasaki fishing port; introduction of clean energy vehicles to public facilities; utilization of ligneous biomass energy, etc. (NEDO)

  1. Evaluation report on the development of ultra-solid lubricant with cluster diamond; Cluster diamond wo riyoshita kotai junkatsu fukugo zairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The fiscal 1998-2000 results of efforts to develop cluster diamond (CD)-diffused solid lubricant composite materials expected to exhibit excellent lubrication are stated. Since friction greatly affects machine life and energy efficiency, friction reduction is an important task. Very hard and microscopic CD was utilized for the achievement of a friction coefficient of 0.08. A manufacturing technology for molds 10nm or smaller was developed, which enabled the development of a gear not larger than 8mm. The success will enable the operation of micromachines in the absence of lubrication which is impossible at present. A CD-aided functional layer creation technology was also developed. It is expected that the development and practical application of micromechanisms will make rapid progress in the 21st century. Much is expected from the creation, and goods with the achievement applied thereto, of advanced technologies whereinto non-lubrication, functional layer creation, and excellent heat conductivity are incorporated. It is quite significant that, since CD is available in any field as far as light-load low-speed sliding conditions are satisfied, sliding parts will be improved and service life will be prolonged. (NEDO)

  2. 1998 Annual Study Report. New industry supporting type international standard development program (Comprehensive survey); 1998 nendo seika hokokusho. Shinki sangyo shiengata kokusai hyojun kaihatsu jigyo (sogo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Summarized herein are results of the survey on a total of 13 themes for international standardization. These themes are for standardization of (1) color control, (2) securing interoperability between optical disk systems, (3) digital image processing for home digital electronic appliances, (4) securing interconnectability between home electronic information appliances, (5) production process systems, (6) testing and evaluation methods for fine ceramic materials for communications, (7) evaluation methods for high-temperature properties of new glass melts, (8) corrosion testing and evaluation methods for surface-treated steel plates, (9) testing and evaluation methods for high-purity titanium, (10) testing and evaluation methods for plastic optical fibers, (11) evaluation methods for high-strength, large-size steel pipe characteristics for superhigh-pressure natural gas pipelines, (12) methods for measuring mileage of hybrid electric vehicles, and (13) methods for determining recycle ratios of automobile components. This comprehensive survey also includes overseas trends for the standardization, establishment/expansion of the international standardization processes, and standardization for determining recycle ratios of home electric appliances. (NEDO)

  3. Fiscal 1999 technical survey report. Basic survey of prioritized fields in South Asia (India); 1999 nendo Minami Asia chiiki (Indo) juten bun'ya kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For working out and proposing project themes optimum for the popularization of technologies for effectively utilizing energy in India, a basic survey was conducted into India's energy policy, trend of supply and demand, steelmaking industry, papermaking industry, petrochemical industry, and chemical fertilizer making industry. India in fiscal 1997 consumed 374-million tons of energy in terms of oil, 30% in oil and 63% in coal. Activities were vigorous for the development of oil substitutes such as photovoltaic and wind power. The steelmaking industry that produced 22.12-million tons in fiscal 1996 was found to suffer from a reduced operating rate due to aging of facilities and from poor infrastructures such as harbor and railway facilities wanting maintenance. It was inferred that energy conservation facilities and technologies of Japan's steelmaking industry would work effectively. The cement making industry was found modernized, but faced the problem of the high cost of electric power. The papermaking industry was busy enhancing its own production capability. The fertilizer making industry ranked third in the world in terms of production, but the energy consumption rate at its ammonia plant was too high. The petrochemical industry was well developed, with Japan's technologies incorporated into it in the design stage. (NEDO)

  4. Leading survey and research report for fiscal 1999. Survey and research on supercompiler technology; 1999 nendo supercompiler technology no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Survey and research are conducted into the global computing technology and the next-generation parallel computer for their compiler technology and programming environment-related technology, which is for the preparation of basic key technologies for the embodiment of high-performance computing for the next generation, and efforts are exerted to extract and define technological problems and to deliberate a research system to achieve the goal. This fiscal year's achievements are mentioned below. Two territories were provided to be respectively covered by a Parallel Compiler Working Group and a Global Computing Working Group whose activities centered about overseas surveys and short-term reception of researchers from abroad. The Parallel Compiler Working Group was engaged in (1) the technological survey of the latest parallel compiler technology and, in its effort to execute researches under the project, in (2) the materialization of the contents of technology research and development and in (3) the materialization of a technology research and development system. The Global Computing Working Group was engaged in (1) the technological survey of the latest high-performance global computing and in (2) the survey of fields to accept global computing application. (NEDO)

  5. Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

  6. Report on the FY 1999 research survey on the development of high ductile chromium alloys; 1999 nendo koensei kuromu gokin no kaihatsu ni kansuru kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D of chromium alloys had been conducted till about the 1970s, which brought the unfavorable results. That's why chromium alloys are brittle at normal temperature and difficult in processing. However, the technology development in recent years review them. The development is earnestly desired also of the materials exceeding the Ni base super alloys which are heat resistant materials for power generation. Cr is rich as resource and light-weighted, and the oxidation film is stable and self-restorational at high temperature. The alloys are excellent in processability at normal temperature and excellent also in toughness. The nitrogen content is strongly concerned with brittleness and intergranular fracture at normal temperature. Therefore, Cr alloys were trially manufactured by the HIP sintering/hot forging method using electrolytic Cr powder with high-purity (99.99%) and low-nitrogen (10ppm) to study a possibility of improving brittleness at normal temperature, mechanical properties at high temperature, oxidation resistance, high-temperature corrosion resistance, etc. A variety of excellent characteristics of Cr alloys were made clear. However, also made clear were the problems: strength is low at normal temperature/high temperature; screw process is impossible because of high notch sensibility; those are not almighty high-temperature corrosion resistant materials. Further efforts should be exerted for the commercialization. (NEDO)

  7. Regional new energy vision formulation project for Takarabe Town. Report; 2001 nendo Takarabe cho chiiki shin energy vision sakutei tou jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For promoting the introduction of new energy and for elevating people's consciousness of such in Takarabe Town, Kagoshima Prefecture, surveys and studies were conducted concerning the energy consumption profile of the town, the amount of new energy resources in existence, and new energy introduction plans, and then a vision was formulated. The town's energy consumption is estimated at 879.350-million MJ/year, with the transportation sector responsible for 46.6%, the industrial sector for 23.0%, the residential sector for 18.7%, and the people's livelihood-related business sector for 11.7%. Oil-based fuels occupy 70.4%, electric power 18.9%, and LP gas 8.4%. New energy introduction projects were studied, which included the introduction of photovoltaic power into the town office; photovoltaic power and hybrid power-lighted light for an oasis-on-the-road project and school facilities; introduction of cogeneration, wind power, and photovoltaic power into a hot spa health center and a water-friendly park; small-scale hydropower in the Okawara valley; wind power generation on Mount Shiraga and Jingaoka; introduction of clean energy vehicles for official use; and compost manufacturing and power generation using livestock waste. (NEDO)

  8. FY 1999 report on the results of the investigational study of dioxin emission mechanism/control; 1999 nendo dioxin hassei kiko yokusei chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of promoting the utilization of energy from waste, studies were conducted on the dioxin emission mechanism and non-Br base fire retardant materials which emit no Br base dioxin, and the FY 1999 results were summarized. In the study, using a small-fluidized bed experimental incinerator, survey was made of effects of organic/inorganic chlorine included in solid general waste on the formation/discharge of dioxins. As a result of the experiment, it was found out that organic chlorine compounds discharge more dioxins than inorganic ones, and that the combustion method in which rapid formation of volatile matter in furnace is controlled to realize the homogeneous mixed state is important for control of dioxins. In the study of non-Br base fire retardant materials, a preliminary experiment was conducted on new fire retardant materials added with inorganic carrier, metal complex, etc. to make the confirmation of fire retardation by liquid phase reaction of polymer in combustion conditions and the study of fire retardation by separating liquid phase reaction, pyrolysis reaction, and gaseous phase reaction. Further, simulation of the combustion of polymer materials was carried out. (NEDO)

  9. Report on survey in fiscal 2000 on the feasibility study on structuring research aiding net; 2000 nendo kenkyu shien net no kochiku ni kansuru kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A study has been performed on the possibility of efficient utilization of research resources by summarizing the resource information for research and development by the industrial, governmental and academic areas and by providing research organizations with the information through the Internet. As a result of the survey on research aiding cases that apply the network used by the public organizations and corporations inside and outside the country, it was found that Japan often utilizes research facilities and holds seminars having selected regional research organizations, while the U.S. provides large-size aids in wide area, such as technological information service, patent service, and human resource service. A questionnaire survey was conducted on interests toward the necessity of research aids, specific needs for aids, and provided services. As a result, it was revealed that interest toward the research aiding net is considerably high, and strong demands are present in structuring database for the research human resource information, needs information, and information on researchers in different fields. Discussions were given on structuring the research aiding net, wherein the system contents, structuring expense, and the development schedule were presented. (NEDO)

  10. FY 2000 report on the results of the development of the next generation chemical process technology; 2000 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted on the next generation chemical process by which no energy losses are produced and the amount of the waste is made extremely small by the new catalytic reaction, the reaction using next generation separation/reaction membrane, etc., and the FY 2000 results were summed up. As to the development of the selective oxidation technology of saturated hydrocarbon, the basic knowledge/information were obtained on the following: construction of the catalytic principle toward the highly selective catalytic partial oxidation, elucidation of the reaction mechanism in alkane oxidation and design of the high functional catalyst, functional design in butane oxidation, characterization of the alkane oxidation catalyst and the application to the catalytic development, synthesis of the alkane selective oxidation catalyst, etc. Relating to the development of the process technology using the new reaction mechanism, a target value of equilibrium conversion of 10% or more was achieved using membrane reactor in the dehydrogenation of ethyl benzene. Further, as to the high performance selective membrane and low temperature active catalyst that are indispensable to the element technology, the continuous study was made, and at the same time themes in this study were arranged. (NEDO)

  11. Fiscal 1999 research report. Revision of introduction guidebook for wind power generation; 1999 nendo furyoku hatsuden donyu guide book no kaitei gyomu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Expectations are rapidly growing higher in Japan, whose energy supply structure is but fragile, that new energies upon introduction and diffusion will help settle emerging environmental problems such as global warming. For the acceleration of new energy introduction, it is necessary to supply autonomous entities etc. planning to adopt new energies with various materials such as basic knowledge of new energies, cases of successful introduction, and procedures to follow for their adoption. Wind power generation has come to attract attention as a environmentally-friendly clean method of energy supply, and there is a strong tendency towards its adoption. Under such circumstances, a guidebook has been prepared, in which study results are systematically written as to the items to consider before local autonomies etc. install their wind power generation systems. The main items in the guidebook are the outlines of wind power generation, wind characteristics, wind power generation system, precedents of wind power generation, how to conduct studies about wind power generation, construction and maintenance of wind power generation systems, procedures, laws, and regulations relating to wind power generation, and government subsidies for wind power development. (NEDO)

  12. Japan`s Sunshine Project. 1991 annual summary of coal liquefaction and gasification; 1991 nendo sunshine keikaku seika hokokusho gaiyoshu. Sekitan no ekika gas ka

    Energy Technology Data Exchange (ETDEWEB)

    1992-07-01

    Out of the research and development on the 1991 Sunshine Project, the results of coal liquefaction/gasification are reported. The basic research of coal liquefaction/gasification is conducted. The research plan for a 150 ton/day scale pilot plant (PP) is worked out for the development of bituminous coal liquefaction technology by NEDOL process. Data of PSU (Process Support Units) operation, especially, are studied. Concerning the data obtained through dismantling of the 50 ton/day PP in Australia which uses Australian Victoria coal due to completion of its operation and also obtained from its support research, they are reflected in the design of a demonstration plant, and the results are arranged for study. Research and development on refining technology of coal-derived liquid such as Illinois coal liquid and on application technology of its products are made. For the development of coal-use hydrogen production technology, conducted is the research of a high temperature gasification PP by entrained flow bed process which is the core of the coal gasification technology. Elementary study with a 2 ton/day furnace is made for the development of the entrained flow bed coal gasification combined cycle power generation system. Also conducted are PP construction, adjusting operation and the overall research operation.

  13. Interim report on evaluation of research and development of manganese nodule exploitation system; Mangan dankai saiko system no kenkyu kaihatsu chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    This research and development project is aimed at development of the techniques which allow exploitation of manganese nodules occurring on deep sea bottoms (4,000 to 6,000 m deep) on a commercial scale, in order to secure stable supply of the non-ferrous metallic resource and improve general ocean development techniques. This project, established by the national project system, has been implemented cooperatively by the government, academic and industrial circles since 1981. Described herein are the interim results, summarized in the FY 1985. The targets of the phase for developing the individual techniques were set to develop the exploitation system design procedures, and to advance to the next phase by the end of FY 1985, where the consistent, integrated system is to be constructed and tested. The results obtained so far are satisfactory as a whole, both in the elementary techniques and their consistency. The simulations have been conducted, where various conditions are inputted to estimate the movement and exploitation characteristics of the system as a whole in the comprehensive ocean tests. It has been found that the nodule-collecting machine shows nonlinear tracking characteristics (i.e., movement different from that of the exploitation ship), and unsteady movements (i.e., repeated movements of rapid starting and stopping). (NEDO)

  14. Fiscal 2000 survey report. Basic research on hot molding of amorphous ceramics; 2000 nendo amorphous netsukan ceramics seikeiho ni kansuru kiso kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Experiments were conducted on the plasticity processing of heat resistant ceramics making use of the viscous deformation of amorphous ceramics in the supercooled liquid temperature domain. Concerning the preparation of powder of amorphous ceramics, the plasma rotating electrode method of Institute for Materials Research, Tohoku University, was employed, and a bamboo leaf shaped amorphous flake was successfully fabricated by increasing the arc discharge current. In a search of texture easy to turn amorphous, it was observed that Al{sub 2}O{sub 3}-La{sub 2}O{sub 3} had a supercooled liquid domain of as large as 70K, and this enabled a conclusion that it was a promising candidate for hot molding in a supercooled liquid domain. In an experiment of molding in a supercooled liquid domain, Al{sub 2}O{sub 3}-Gd{sub 2}O{sub 3} was used in a press molding process. As the result, a compact bulk mold was obtained in a temperature domain far lower than in the case of conventional sintering. Crystallization had already advanced in all the molds experimentally fabricated by press molding, and this disabled a study of characteristics to be exhibited by an amorphous mold, but it was found that they had a compressive strength of approximately 1,800MPa. (NEDO)

  15. Report on results of the survey for drawing new energy visions for the Town of Shiranuka district; Shiranukamachi chiiki shin energy vision sakutei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The new energy visions are drawn for Town of Shiranuka. Utilization of solar energy is at the top of the prospective new energy reserves for the town, followed by utilization of heat of wastes, biomass energy (in the stock raising industry), and photovoltaic power generation. The expected recoverable new energies account for approximately 35% of the total annual energy consumption of the town. The basic guidelines for introduction of new energies are drawing the priority projects which place importance on environmental education and bringing up talented persons, development of the soft policies for supporting the citizens and related entrepreneurs, and introduction of new energies for promoting new industries. The priority projects include hard ones, e.g., foundation of Eco-school Shiranuka, Eco-park Kushiro/Shiranuka (biomass energy supply center) and Koima new energy park, and soft ones, e.g., establishment of the new energy grand prize awarded by PR brochure ''Shiranuka'', foundation of the Shiranuka fund for introduction of new energies, construction of a Shiranuka Citizens' power station, and rent-a-car project for eco-car test runs. (NEDO)

  16. Fiscal 2000 survey report on the survey and research on green technology industry; 2000 nendo green technology industry ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The approaches of the Government and local autonomies to green technologies are surveyed toward the construction of a green technology industry. The present activities and future outlook of environmental industries interested in green technologies are surveyed and examined, the green technologies here including (1) energy conservation measures and development of non-fossil fuels, (2) energy-related and environmental measures for countering global warming, (3) waste treatment measures for countering dioxins and endocrine disrupters. A survey is conducted of the outlines and future trends of green technology related important studies now under way at laboratories and research institutes of universities, the Government, and private-sector corporations. Based on the results of the surveys, important subjects of technical development in green technologies are extracted and studied for the possibility and outlook of their practical application. Tasks to discharge and problems to occur before they are introduced to the market are also evaluated and confirmed. Based on the results of the research and development of green technologies, actualities of environmental industries are taken up, and the problems and tasks to be settled before environmental technologies are introduced to the market are investigated and studied. (NEDO)

  17. Report for fiscal 1998 on a new energy vision establishment in Yonaguni Township; 1998 nendo Yonagunimachi shin energy vision sakutei hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Discussions were given and establishment was made on the new energy vision at Yonaguni Township in Okinawa Prefecture. The overall image of the new energy introduction vision at Yonaguni Township may be depicted by the wind power generation project to be implemented by the Development Public Corporation, by which megawatt-class wind power generation facilities will be built for effective utilization of the power by the whole island. Surplus electric power generated in a great amount in a certain season will be utilized for high value addition by electrifying agricultural works, expansion in production, (water pumping-up for irrigation, prawn cultivation, and sugar making factories), and melting and volume reducing of refuses. In addition, new type batteries for power storage with large capacity will be introduced to achieve stable power supply and introduce electric vehicles for official use and tourism business. Solar cells and small wind mills subject to stand-alone utilization will be arranged along sightseeing roads in the island, on tourism facilities and sightseeing infrastructural facilities. Careful considerations will be given on introduction and arrangement of the new energies for harmony with scenery of the island. Transmission wires related to the new energy utilization will be laid underground. (NEDO)

  18. Fiscal 1997 report on the introductory study. Human behavior recognition evaluation technology; 1997 nendo sentan kenkyu hokokusho. Ningen kodo ninchi hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Importance of the human behavior technology was paid attention to to get true safety and comfortableness of life through adaptability of products/systems to all humans. In consideration of the social and technological background, the human behavior recognition evaluation technology avoids economic/social losses caused by accidents and troubles and also provides the safe life environment for living people including the aged. Further, the gist of the project was proposed to make it clear that it can give a course of making things from a viewpoint of development of products dealing with individuals (personal fit) and can give new added values and contribute to heightening of international competitiveness at the same time. Development is made of technology of dividing concrete behavior patterns into types and also accumulating them in usable forms at the time of product design and in emergency and of technology of measuring all the time information on human behaviors in daily life without restrictions and on site. Supporting technology is developed for making the most of behavior information of users for product design and in emergency. Effects of the spread are also estimated. 76 refs., 13 figs., 9 tabs.

  19. Fiscal 2000 pioneering research report on the research on advanced safety helicopter; 2000 nendo advanced safety helicopter no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted concerning helicopter operating environments and the trends of related technologies in Japan and abroad, and the needs and seeds were grasped. Research was made to study technical problems and measures to solve them for the development of a safe, low-noise, and low-cost next-generation advanced safety helicopter (ASH). A market research was conducted on traffic systems in the future, state of aviation-related infrastructures and their future, current state of people's daily life which centers about locomotion, and the effect that ASH would impose on society. A technical research was carried out relative to flight safety, which involved EVS (enhanced vision system), information display system for helicopters, collision avoidance advisory for pilots, air collision prevention system/surveillance system for helicopters, obstacle detection/warning system for helicopters, blade deicing system for helicopters, and so forth. Detailed investigations were also conducted for technologies for reduction in the manufacturing, maintenance, and development costs, and for reduction in noise. (NEDO)

  20. Report on results of contract research. 'Research on MHD generation system'; MHD hatsuden system no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    'Research on MHD generation system' was implemented by its expert committee in the electric joint study group, with the results of fiscal 1980 reported. This year, a detailed conceptual design was carried out on a coal fired MHD generation system, with points for the technological development concretely examined. In addition, investigation was conducted on the progress of MHD generation technology, development situation of other generation systems, state of energy resources, etc., in various foreign countries. In the conceptual design of the coal fired MHD generation plant, the system structure of a 2,000 MWt class commercial MHD generation plant was explained, as were the conceptual design of the structural elements and proposals for a 500 MWt class demonstration plant and an 100 MWt class experimental plant, for example. In the overseas trend of R and D on MHD generation, investigations were made concerning the U.S., Soviet Union, and China, with details compiled for such items as generation plants, combustors, generation channels, heat resisting materials, superconducting magnets, heat exchangers, seed slags, inverters, boilers and environments, and commercial plants. (NEDO)

  1. Report for fiscal 1998 on the international joint research project of medical welfare equipment; Iryo fukushi kiki kokusai kyodo kenkyu jigyo 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In connection with the international joint research project of medical welfare, a report was made on the results of the investigation conducted in 1998 concerning the technology of overseas medical welfare equipment. In the investigation of china, observation was made on the actual state of the representative medial institutions, with opinions exchanged. Obsolete equipment and old technology are the present state in China, which is strongly desirous of exchanging information with Japan. In Taiwan, being full of venture spirit, an ultrasonic thermal treatment apparatus and an ultrasonic echo device have been produced for example. In Europe, an observation tour was conducted on a German manipulator and process robot while an investigative visit and exchange of opinions were made on the living environment and facilities in Italian training center for physically handicapped persons. Japan's self-supporting and assisting system for excretion attracted many questions and comments. In the investigation in the U.S., views were exchanged concerning '{sup 13}C-MRS device for non-invasion brain metabolic measurement' in research institutions such as universities. A machine developed in Japan received a high evaluation in that {sup 13}C spectrum was obtained from a substantial depth. (NEDO)

  2. Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

  3. Leading research report for fiscal 1998 on the next-generation cold emission technology; 1998 nendo jisedai cold emission gijutsu no chosa kenkyu sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The report covers the fruits of researches into technologies of cold emission control and cold emission application conducted in fiscal 1998. In the study relative to the current status of cold emission control technology, emitter materials that govern electron emitting characteristics are discussed, such as metallic materials, silicon, carbon systems, semiconductors, liquid metal, etc. In relation with the application of semiconductor process technology, the tunnel emitter is taken up that utilizes the semiconductor tunnel cathode. In relation with the cold emission process, an emitter high in aspect ratio is described, obtained by the inductive emitter deposition method in which organic metallic gas is decomposed by an electron beam. In the study of the cold emission control system and instrumentation, the merits and demerits of control by MOSFET (MOS field effect transistor) are discussed. In relation with the technology of cold emission application, FED (field effect display) development and problems, current status of sensor technology and problems, RF application technology, application to power systems, etc., are mentioned. (NEDO)

  4. FY 1999 achievement report on the R and D of welfare techno-systems (Kyoto); 1999 nendo welfare techno system kenkyu kaihatsu (Kyoto) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were carried out of various kinds of physically functional substitution equipment which supplements the worsened functional ability of the aged/handicapped. In the research on various prototypes of physically functional substitution equipment, experiments on the use were conducted using Japanese speech recognition devices/programs which are standard products commercially available, so that the aged/handicapped can operate equipment (various devices such as home electric appliances) by speech (words). Further, the specifications were studied for technology to use the Japanese speech recognition technique for physically substitution functions. In the R and D of information infrastructure and various kinds of physically functional substitution equipment, the specifications were established for technology to operate lighting equipment, heater and TV by the Japanese speech, and the experiment was made using the prototype manufactured. As a result, the power source operation by speech of TV/lighting desk lump/electric stove has been finished almost certainly. Further study is needed such as TV channel selection by remote control. The investigation was made of the aid needs for the handicapped. (NEDO)

  5. Fiscal 2000 achievement report. Research and development of low-pollution brown coal utilization technology; 2000 nendo seika hokokusho. Kattan no teikogai riyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Studies were made for developing low-pollution easy-to-operate industrial furnaces for use in small and medium size plants in Indonesia. In this fiscal year, two kinds were selected out of Indonesia yielded brown coals, which were then subjected to test combustion in a bench scale fluidized bed combustor for examination for their combustion characteristics and environmental impact generating characteristics. The nitrogen oxides from the brown coals were found to mark approximately 100 ppm at an excess air ratio of 1.4, which was higher than in the case of bituminous coal. The NOx concentration level was found to be lower in the circulation fluidized bed boiler than in the spreader stoker fired boiler. Combustion efficiency exceeding 98% was achieved. A survey was conducted of brown coal users in various industrial fields in Indonesia. It was then concluded that the tested method not be recommended for use in small businesses in the textile industry because there would be no economic profit or improved efficiency for them but that it would be feasible in the plantation industry where the fluidized bed combustion/heat exchanger aided indirect process and the use of electrical dust precipitators would protect products from contamination. (NEDO)

  6. Fiscal 2000 report on results of R and D of welfare techno-system in Takaoka City; 2000 nendo welfare techno system kenkyu kaihatsu (Takaoka) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    R and D was conducted on a 'system for monitoring living situation of elderly people' for the purpose of supporting the elderly living alone, with the fiscal 2000 results reported. In the development of a knowledge engineering system, a system was developed estimating the present position of an elderly person in his home or calculating his daily living activities, by analyzing data measured by infrared sensors, and thereby automatically inferring his behavior or health condition. In the research for practicability of the system, infrared sensors and sensors for detecting opening/closing of a door were improved, which included improvement by using telephone lines for example. In the demonstrative experiment, data were obtained which seemed to show a change for the worse of a disability condition due to senile dementia, or else, which appeared to be an inability to move occurring finally as a result of gradual deterioration of health. Another data measured disclosed that elderly people, unlike a normal life pattern, were living in a state with night and day reversed. From these results, the system can safely be said to have a function for monitoring the lives of the elderly people in point of their mind and body. (NEDO)

  7. FY 1996 annual report of investigation on biological fixation of carbon dioxide. 2; 1996 nendo seibutsuteki CO2 kotei ni kansuru chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Various kinds of biological fixation processes of CO2 were evaluated from the various viewpoints. Afforestation of tropical and temperate areas, greening of desert, biomass energy production in these areas by energy plantation, coastal mangrove plantation, fertilization with nitrogen and phosphate to outer ocean and coastal, upwelling zone fertilization with iron, and coral reef expansion combined with OTEC (ocean thermal energy conversion) were comparatively investigated as the selected measures. As a result, the cost of CO2 fixation by cultivation of sea weed and plankton was much higher than that of afforestation. The iron fertilization method which was considered to be one of the high CO2 reduction potentials might be economical. However, its effect could not be quantitatively evaluated. The afforestation of tropical and temperate areas seemed to be most feasible in a short term from the viewpoints of economy and environment. It was suggested that the establishment of a systematic water management technology could make greening and afforestation of desert. 76 refs., 27 figs., 28 tabs.

  8. Fiscal 1996 report on technological results. R and D on micromachine technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Researches on basic element technology of micromachines are conducted that operate autonomously in a narrow small part in a complicated apparatus or in vivo. The areas of activity are (1) research on micromachine systems, (2) a subminiature liquid synthesizing system, and (3) comprehensive investigation and research. In (1), the researches were carried out on the miniaturization and functional combination of a micro laser catheter and a micro tactile sensor catheter, which are the primary components of a coeliac diagnostic and therapeutic system, a 'micro catheter for cerebral blood vessel/treatment', as a micromachine system in the medical field. In (2), R and D was conducted on a system element technology assuming it contributed to a subminiature liquid synthesizing system capable of preparing various liquids including pharmaceuticals accurately with a trace amount. In (3), examination was made on the application area of a micromachine system with priority given to a medical field and also on technological subjects to be tapped, as well as on the contents of (2), with a device installed for evaluating the operating characteristic of a distribution type fluid actuator as needed for the development. (NEDO)

  9. Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

  10. Fiscal 1975 Sunshine Project. Technology assessment on coal gasification and liquefaction; 1975 nendo sekitan no gas ka ekika gijutsu no technology assessment seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-31

    This research was intended to find the desirable direction of technological development, by discussing the effects of coal gasification/liquefaction technologies from every angle, for the purpose coping with the social demand for steadily and continuously obtaining clean energy. This year, the examination was conducted not only on the energy conversion technologies of coal gasification/liquefaction, but also on the impact generating from the entire supply system of coal energy from coal mine development to mining, transportation, storage and conversion to secondary energy. For this purpose, while the outline was grasped of coal resources in the world as well as each technology for the mining, transportation, storage, electric power generation by gasification, and high calorie gasification, a case study was made on the assumption that electric power generation and high calorie gasification were conducted by importing 1,000 tons of coal from overseas, extracting the impact on the basis of this case study. In addition, examination was made on the position of coal energy in the energy supply of the future, with an impact investigated on condition that about 300 million tons were imported equivalent to roughly 16% of energy supply in the year 2000 or about. (NEDO)

  11. Achievement report for fiscal 1998 on Welfare Technosystem Oita research and development; 1998 nendo Walfare technosystem kenkyu kaihatsu (Oita) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Before a welfare facility is introduced into a home, studies should be sufficiently conducted about the circumstances of daily life, not only of the aged user but also of the family members who take care of the aged user. In the development of handrails, it is found that plastic foam containing wood flour presents the feel of wood, easy to bend when heated. Materials are investigated for flexural strength, and ABS (acrylonitrile butadiene styrene) is chosen as the suitable material. As for devices to assist toileting, a system is developed under which the patient's legs are raised. Since there are arguments for and against the operation itself of mechanically raising a patient's legs, however, efforts will continue to develop much advanced systems. In the study of walk and transfer behavior, a toilet frame mockup is designed and manufactured, which is for collecting data. In an preliminary experiment, tests are conducted about a transfer from a chair to another and, assuming a physically handicapped patient, a transfer from a wheelchair. The data thus collected are to be subjected to analysis and image processing by the use of measuring sensors. Development is described of interfaces, for use in devices to serve as information mediums, which consider the cognition characteristics of the aged people. As for the development of devices for communication, environmental control, and display, their basic operation and feasibility are discussed. Actualities of costumes for physically handicapped people are also investigated, and development is carried out as required. (NEDO)

  12. Report on the geothermal development promotion survey. No.B-6. Mt. Tsujinodake area; Chinetsu kaihatsu sokushin chosa hokokusho. No. B-6 Tsujinodake chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper summed up the results of the geothermal development promotion survey B 'Mt. Tsujinodake area' which was carried out at Yamagawa town, Ibusuki county, Kagoshima prefecture, from FY 1997 to FY 1999. In the survey, the following were conducted: surface survey such as geology/alteration zone survey, fluid geochemical survey, gravity exploration and electromagnetic exploration, and geothermal fluid survey by drilling 4 structural testing boreholes. In the Mt. Tsujinodake area, active fumarolic activities are still now continuing around the Unagi hot spring in the north, and the acidic alteration zone is distributed in the peripheral surface area. In Borehole N11-TD-2 in the north, it is assumed that there exists the hydrothermal bed of a temperature of approximately 230 degrees C in the depth of 400-800m, which is comparatively shallow, and that the stored geothermal water flows laterally. In the central area, a hydrothermal bed of a temperature of approximately 130 degrees C was confirmed in N11-TD-1, but it is judged that chances of the existence of high temperature hydrothermal bed are not very good. In N11-TD-3 in the south, the existence of promising heat sources is expected in the deeper part since the remarkable alteration was seen in the depth of 1,435m or deeper, and the sharp rise in temperature was recognized. (NEDO)

  13. FY 2000 report on the results of the R and D of solid oxide fuel cells (SOFC); 2000 nendo kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    Development of fuel cell power generation technology and R and D of solid oxide fuel cells were carried out, and reports of the FY 2000 results of companies were summed up. As to the R and D of the cell module, the R and D on the wet type cylinder module were made jointly by Toto Ltd., Kyushu Electric Power Co. and Nippon Steel Corp. As to the R and D of materials/basic technology, the following were conducted: evaluation of reliability of the cell module (evaluation of thermal cycle characteristics, etc.) by Chubu Electric Power Co., evaluation of reliability of the cell module (cell characteristics/stress evaluation) by Tokyo Gas Co. Ltd., cost reduction of cell materials (evaluation of chemical characteristics) by Central Research Institute of Electric Power Industry, and cost reduction of cell materials (evaluation of mechanical/thermal characteristics) by Japan Fine Ceramics Center. Concerning the system study, study of the system (adaptation fields of the small system and the optimization) was conducted by Nippon Steel Corp. (NEDO)

  14. Report on investigation in fiscal 2000 related to improving APEC industrial technology indicators; 2000 nendo APEC sangyo gijutsu indicator seibi kanren chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to strengthen cooperation in the research and development field in the APEC areas, a database was structured on such data as research and development assistance institutions in each country, research and development budgets, human resources for research and development, such governmental regulations as research visa issuing procedure and foreign capital control, research and development trends in private business entities, major research and development organizations, and evaluation on research and development environment in private business entities. The introduction of the report describes the background of the investigation, and factors for internationalization of research and development. Trends were investigated on research and development in the eight nations; the Philippines, Thailand, Korea, China, Singapore, Taiwan and Malaysia. Specifically, investigations were made in China on the research and development statistics, research and development programs, investment trends, small to medium business entities, promotion of research and development, the result of the 1999 APEC investigation, computer software, computer net services, and electronic trading (e-commerce). In the Philippines, six items were investigated, such as the economy trends and prospects, the result of the 1999 APEC investigation, case studies, and small to medium business entities. (NEDO)

  15. FY 1993-1999 report on all the results of the development of high performance industrial furnace; Koseino kogyoro no kaihatsu sogo seika hokokusho (1993 - 1999 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Since an phenomenon was found out that NOx emission, which was thought to be increased, will be decreased by burning the high temperature preheated air jetting it at high speed (high temperature air combustion) in industrial furnace, there appeared a possibility of technical breakthrough for achieving the heightening of energy utilization efficiency and NOx reduction by exhaust heat recovery at the same time. This project aims at conducting full-scale experiments based on the basement technology including the theoretical elucidation of the combustion mechanism and high temperature air combustion by using various experimental facilities. Further, making full use of the most up-to-date analysis methods and constructing general-purpose database, the development is also aimed at of high performance industrial furnaces such as various heating furnace, heat treat furnace and melting furnace, with the assumption of prompt commercialization of the results of the development. As a result, targets were achieved such as energy saving of 30% or more, downsizing of 20% and a remarkable NOx reduction. Core technologies of this project are in-system limit heat recovery technology, high temperature air combustion technology, temperature field control technology (furnace temperature leveling technology) and high exergy heat transfer technology (furnace temperature heightening technology). (NEDO)

  16. Fiscal 1998 research achievement report. Development of key technology for high-efficiency semiconductor manufacturing process; 1998 nendo kokoritsu handotai seizo process kiban gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    In the development of large-aperture/high-density plasma technology, research and development was carried out for balanced electron drift plasma technologies for uniform control of plasma density and the like, such as an excited plasma source and plasma drift to enable wide-range plasma generation in a chamber. In the development of high-efficiency exposure technology, studies were made for stable generation and control of short wavelength excimer laser and for higher-speed large-aperture mask writing by use of an electron beam. In the development of higher-speed processing and energy-efficient technologies, research and development was conducted involving probe card technology for increasing the speed of semiconductor inspection, software-aided virtual tester technology, local energy-efficient cleaning technology in wafer processing and transportation, sheet-type flexible manufacturing system, and the like. (NEDO)

  17. Report on new energy vision establishment project in Higashi Naruse Village area; Higashinarusemura chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established in the Higashi Naruse Village in Akita Prefecture. The population of the village is continuing the decreasing trend since 1950 to 3,390 persons as of 2000. The annual energy demand in this village is about 320,000 GJ, accounted for by the consumer department at about 40%, the transportation department at about 36% and the industrial department at about 24%. The carbon dioxide emission amount therefrom is estimated 6,300 t-C annually. The expected usable quantity of new energies in the village would be available, in the decreasing order, in the wind power as the most promising source, forestry bio-mass, snow cold heat energy, agricultural bio-mass, and solar beam (heat). The total quantity would be 514,330 GJ annually in heat utilization, and 85,305 MWh in electric power. The new energy introducing project includes introduction of photovoltaic and wind power generation into Kurikoma Mountain Villa, introduction of wind power generation into the Junes skiing area and Oyanagi Natural Park, introduction of photovoltaic power generation and heat utilization into primary and middle schools, introduction of clean energy fueled automobiles into the village office, and introduction of photovoltaic power generation into general houses. (NEDO)

  18. Report on investigation of initial stage of energy-saving vision in Ikeda City region; Ikedashi sho energy vision shoki dankai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Investigation was conducted for the purpose of deciding energy-saving vision in the region of Ikeda City, Osaka Prefecture. Ikeda City is lower in the use of electric lights per household than Osaka Prefecture or the whole country, and is higher in the consumption of city gas. The carbon dioxide exhaust of the City is less compared with that of Osaka Prefecture or the whole country. As to new energy, there is a good possibility of the use of solar energy. As a result of energy conservation diagnosis, about 25% energy saving was found possible in the government office building jointly used by the City and the Prefecture, and 21% in Kitateshima Junior High School. From these investigative results, proposals were made for the basic policy of the energy saving vision; they were, for example, to enrich one's life style by promoting efficient use of energy, to build an urban structure having less energy load, to enhance all citizens' consciousness about energy, to change the way of living by the community unit, to take the lead in energy conservation as the city administration to set an example for the whole city, to foster the environmental industry by dealing with energy problems, and to have a long-term outlook and tackle the issue with stress placed on feasible projects. (NEDO)

  19. Fiscal 2000 report on result of R and D of underground storage technology for carbon dioxide; 2000 nendo nisanka tanso chichu choryu gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    This paper presents the fiscal 2000 results of R and D of underground storage technology for carbon dioxide. As basic experiments, a measurement apparatus was manufactured for simulating the pressure and temperature conditions in aquifers to measure the rate at which CO{sub 2} is dissolved in water and the reactivity between CO{sub 2} and rocks, with the basic performance verified. Methods were investigated and classified that monitor environmental impact and safety. For the purpose of anticipating the long-term behaviors of CO{sub 2} sequestered underground, a simulator was developed, extracting, from investigation of the literature, natural phenomena required for the anticipation. As the system studies, examination was conducted for analysis of the energy balance of the underground storage technology, rational design (safety and economy) of an entire system ranging from source to storage point, investigation from social and economic perspectives, and estimation of the effect of suppressing global warming. In the injection experiment, Minami-Nagaoka natural gas field was selected as a prospective experiment site from the characteristics of the cap rock and aquifer. One injection well was drilled to a depth of 1,230 m, with investigations performed such as physical well-logging and core sampling. Existing data were utilized in the simulation study of CO{sub 2} behavior underground during the injection period. The information of the basic geophysical survey/exploratory well by the Japan National Oil Corporation was collected and compiled, with the preliminary geological study undertaken in the areas described. (NEDO)

  20. FY 1984 annual report on the research and development of automatic sewing systems. Total systems; 1984 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. Total system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    The automatic sewing system technique research association has been commissioned by the Agency of Industrial Science and Technology for (research and development of automatic sewing systems). This program covers R and D of the elementary techniques for total systems and sewing preparation/processing, sewing/assembling, cloth handling, and system management/control. This report describes the results of the R and D efforts for the total systems. For producing diversified products in small quantities, which is the object of this R and D program, the target is set to reduce processing time by at least 50% from the current level. The efforts to achieve this target by solving the problems involved therein are made from the side of developing FMS and FA procedures, and apparel side. The program for the former investigates the required functions of individual sub-systems that constitute the total system, to clarify the technical targets of the core elementary techniques for each sub-system. The program for the latter analyzes the sewing steps for producing diversified clothes types, specifications for automatic operation, integration, standardization and coding of the steps, and so on, based on the results of studies on basic apparel types. (NEDO)

  1. Research report on the trend of preventive measures against global warming by substituting CFCs; Daitai freon no chiku ondanka taisaku doko ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper reports the research results on the present state and future trend of protective measures for the ozone layer, and the trend of preventive measures against global warming by substituting CFCs such as HFC, through international conferences, meetings and lecture meetings, and literature survey. In the 8th meeting of the parties to the Montreal Protocol, it was presented that refrigerator producers in Thailand phased out CFCs from their products earlier than the schedule in cooperation with Japan. The final draft including the approval of essential use from 1997 to 2002 was reviewed, and reported to the technology/economy assessment panel. Reduction of ozone depleting substances was guided in Thailand, Indonesia and Philippines. The latest trend of substituting technologies of HCFC was surveyed, and the control trend of F-containing greenhouse effect gas emission was also surveyed through the conference of the parties of climate change in fiscal 1996. Based on the IPCC report in 1995, the emission amount of greenhouse gases of nearly 10% in contribution such as CO2, methane and fluorocarbon was arranged. R and D on destruction of CFCs was also surveyed. 35 refs., 54 figs., 32 tabs.

  2. Report on the FY 1982 potential survey of overseas coal development. Coal fields in Mexico; 1982 nendo kaigaitan kaihatsu kanosei chosa hokokusho. Mexico kaku tanden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-10-01

    The following surveys were made to acquire the data/information for potential study of development/import of Mexican coal: (1) collection of general information such as energy situation, coal situation and infrastructure. (2) survey of situation of coal seam existence, coal quality, coal amount, exploration/development, etc. of Sabinas coal field, Monclova, Coahuila state, San Marcial coal field, San Enrique, Sonora state, and Tezoatlan coal field, Tlaxiaco, Oaxaca state. (3) data collection for potential study of future development. The area where coal is presently produced is only Coahuila state, and also there the exploration is comparatively being advanced. In states of Sonora and Oaxaca, the exploration is only made roughly by CRM, and the exploration is going to be detailedly made from now. The exploration in Coahuila state, however, was made only down to 400m under earth's surface. In this area, coal existence down to 1,000m under earth's surface is expected, and the exploration deeper than 400m is a future subject. Ninty percent of the present coal reserve is produced from Coahuila state. They are coking coal and steam coal in quality. At present, the Mexican government is exerting efforts to increase production of the domestic use coal, with no intention of exporting coal. Seeing how the exploration would go, it is necessary to watch the results of the survey on a long-term basis. (NEDO)

  3. Achievement report for fiscal 1984 on Sunshine Program. Basic research on coal type and gasification characteristics; 1984 nendo tanshu to gas ka tokusei no kiso kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    The study of pressurized fluidized gasification of coal chars started in fiscal 1975, and a 0.2t/d unit was in operation until fiscal 1979. Since fiscal 1980, a 1t/d unit has been in operation. In fiscal 1984, an entrained bed gasification furnace was constructed, capable of high-temperature gasification of various coals, and it is now undergoing a test operation. This report consists of pressurized gasification tests for coal char, the result of a study on the effect of coal type on the char gasification reaction rate, and the result of experiments on the treatment of coal liquefaction residue, all accomplished in the 1t/d gasification unit. For the investigation of the effect of coal type, chars of 13 types of coals are subjected to reaction tests in the carbon dioxide gas, and weight reduction rates and changes in residue surface areas are determined while reaction is under way. The results are analyzed and parameters are made clear that enable a quantitative assessment of the effect of coal type on gasification reaction rates. Pulverized grains and coal liquefaction residue are blended and gasified in the fluidized bed in the presence of oxygen and steam. As the result, a gas capable of 2,000kcal/Nm{sup 3} containing 30% hydrogen and 25% carbon monoxide is acquired, when catalyst grains in the residue are segregated. (NEDO)

  4. Report on surveys in fiscal 2000 on the survey on promotion of freer flow of researchers; 2000 nendo kenkyu jinzai no ryudoka sokushin ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to help discuss the system and environment improvement to promote freer flow of Japanese researchers, surveys and discussions were given on the actual status in America and European countries. In the U.S., results as independent researchers are demanded from the very early time under the severely competitive environment, wherein the fair evaluation of the results allows the researchers to step-up the positions and research environment to which the researchers are oriented. In Germany, a function to promote researcher mobility is available as a system, such as promotion of exchange with other sectors during researcher education course (the internship system at the fourth grade in a university, and power training and performance record building at the Max-Planck Institut during the long term of post-doctoral period before attaining a professor position), or prohibition of inviting university professors into the same faculty. The actual status of Japan not having high mobility of researchers has been caused by the system based on the lifetime employment, whose shortcomings include stiffness in personnel affairs, and reduction in activities of researchers due to aging. (NEDO)

  5. Fiscal 1997 report on the results of the international standardization R and D. Overall survey; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper summed up the results of the survey of tackling with the international standardization by enterprises and organizations involved in the standardization in the U.S., Europe and Japan, the results of the R and D on 20 themes for the international standardization, and the development toward the international standardization. As the R and D themes, the following were selected: the development of chemical method to analyze/evaluate metallic coatings of surface treated steel coating sheets, R and D of the basic evaluation method of functional composite particles, international standards for computer/manikins, basic technology of color image management, study on optimizing design/evaluation technology using quality engineering, study of the international standardization by economic evaluation of environmental impacts, R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells, development of a test method of halogen-free flame-retardant cables and a study of the cable standards, standard measuring methods of hormone effects of chemical substances, quantification of the sensory evaluation and international standardization in the paint field, experimental study on the international standardization for immunochemical measurement of chemical substances, etc. 24 figs., 16 tabs.

  6. Fiscal 1994 survey report. Survey of energy supply/demand structure sophistication and global environmental impact; 1994 nendo energy jukyu kozo kodoka chikyu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Outlines of various energy supply/demand analytical models are surveyed. With environmental problems gathering importance, a number of models are being introduced in which energy supply/demand structures, long-term climate changes, and impacts of policy options on social economy are linked to each other. Some socioeconomic impact models cover a single country and others the whole world. They are various in type, ranging from dynamic optimization models to static balance models. Twenty-four models are chosen, and grouped into two types respectively covering Japan and the whole world from a geographical viewpoint and into three groups in view of their structures. Under an optimization model, such optimization is accomplished as economic growth maximization and energy cost minimization and so forth under given energy supply restrictions. Under a general balance type econometric model, an adjustment process in which capital and labor and production are coordinated across multiple departments is expressly stated. Under a partial balance type econometric model, a demand function for goods is given and optimum behavior such as consumption maximization is indirectly described. (NEDO)

  7. Reports on 1974 result of Sunshine Project. Research on tar sand and oil shale; 1974 nendo tar sand oyobi oil shale ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-04-04

    The purpose of this research is to grasp the policy of the oil sand resource countries, the properties and existing conditions of the resources, effects of the oil sand resources on a long term energy supply/demand, etc., and to clarify the meaning and position of the researches on the development of oil sand resources in the future energy policy of Japan. The quantities of oil sand resources are mostly in the process of investigation except Alberta province of Canada and are estimated to be two trillion barrels. The quantity for which strip mining is possible is about 90 billion barrels, which are mostly located in the Athabasca region. The oil sand holding countries take a policy of positively developing oil sand. No barriers are particularly provided against the introduction of foreign technology and capital. Where the prospects are possible for the development of oil sand are Canada and Venezuela. R and D should be emphasized on the refining of bitumen and the extraction method within the oil reservoir. The investment per b/d is about 15-20 thousand dollars, which is likely to be more than twice as much as for the North Sea oilfields. The properties and quality of the synthetic crude oil are superior while the risk of exploitation is small; therefore, oil sand will be competitive with crude oil in the future. (NEDO)

  8. Report on achievements in fiscal 1998. Research and development of a welfare techno-system; 1998 nendo welfare techno system kenkyu kaihatsu (Sapporo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The surveys and studies having been performed in the present fiscal year are as follows: (1) in the surveys and studies on self-reliant and at-home care-taking for elderly people living in residential houses, using biological information of snowy and cold districts as the parameters, (a) effect of changing the attitude in two-step ascent and descent motions was studied, (b) stair ascent and descent motions were analyzed, (c) standing-up motion using a sitting position handrail was analyzed, and (d) stride-over motion patterns and hip joint movements were experimented; (2) in the studies of a living environment system to support self-reliant way of living of elderly and physically handicapped people in snowy and cold districts, studies were made on (a) shapes of entrance and exit spaces of a residential house, and features of moving motions of elderly and physically handicapped people, (b) living activity patterns and pleasantness centering around the living section in the house of the at-home elderly people, (c) forms of approach spaces for independent residential houses that consider snow disposal: (3) in development and improvement of care-taking devices with importance placed on physical and psychological adapting function of the users and harmony with the users, studies were given on (a) noise characteristics of rooms in which at-home welfare devices are installed, (b) colors and recognizability of switches on welfare devices for elderly persons, (c) drive experiments of moving devices in winter, and (d) motion simulation of ridable devices; and studies were made on (4) moving and riding welfare device systems for elderly and physically handicapped people in snowy and cold districts, and (5) user interface of motor-driven wheelchairs. (NEDO)

  9. Achievement report on research and development on fusion zones in fiscal 1999. Second volume. Chemo-intelligence; 1999 nendo yugo ryoiki kenkyu kaihatsu seika hokokusho. 2. Kemo intelligence

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to artificially realize diverse functions and structures using as a trigger the molecule recognition in living things and organisms, researches and surveys were performed on chemo-intelligence. This paper reports the achievements in fiscal 1999. In a theoretical approach to elucidate inter-molecular interactions, research was performed on hydrogen bondage, CH-{pi} interactions and stacking by using the computerized chemical method. In the design and synthesis of host molecules, development was carried out on a synthesizing method based on large ring compounds and non-ring compounds utilizing the interactions having weak hydrogen bondage, and molecular design utilizing the conformity in sizes and shapes of the molecules. In structuring the host molecules having a function to recognize neutral molecules, research was executed on capturing and activation of neutral organic molecules as the artificial host molecules. In addition, investigations were given on the latest information about separation of ionic substance recognizing compounds and their application to sensing, structure of ultra-molecular construction and the function thereof, and approaches aimed at their use as materials and applications. (NEDO)

  10. Research report of fiscal 1997. Basic research on joint implementation for preventing global climate changes; 1998 nendo chosa hokokusho. Kyodo jisshi kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research was made to promote Activities Implemented Jointly Japan Program. Joint Implementation (JI) is the methodology for preventing global climate changes by collaboration of countries. The countries take cooperative actions for reduction, absorption and fixation of greenhouse gases, and effectively distribute the reduction credits among relevant parties. This was decided in the first session of the Conference of Parties (COP) held in March, 1995. In COP3, Japan`s assigned reduction amount in 2008-2012 was determined as 6% of the emission level in 1990. The protocol defines JI between parties as dealings of emission reduction units, and JI between developing countries as clean development mechanism. The rules for a base line and credit distribution are necessary before full-scale implementation. Although JI is regarded as an important cost-effective project, it is important to decide where and how the JI projects should been promoted. The present state and issues of the primary approved project of Japan Program are arranged. In particular, various terms related to developing countries remain to be solved. 21 figs., 32 tabs.

  11. Report on surveys in fiscal 1999 on research and development of the environment harmonizing catalyst technology; 1999 nendo kankyo chowagata shokubai gijutsu no kenkyu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the surveys in fiscal 1999 on research and development of the environment harmonizing catalyst technology. The discussion subjects taken up included suppression of discharge of carbon dioxide, catalysts used when manufacturing hydrogen and technology thereof, and environment purifying catalysts to decompose harmful substances, and technology thereof. The roles of catalysts and their technologies are expected in reducing the reforming temperatures, achieving energy saving, and reducing decomposition energy. Furthermore, the catalysts are expected of high activity, long life and low cost. Three themes were selected from the emergency and importance points of view. The themes are, in the consumer field, research and development of efficiency improvement in membrane reactors for reforming low-grade hydrocarbons to structure a technology to manufacture hydrogen for small-size portable fuel cells; and in the industrial field, development of hydrogen and carbon product manufacturing technologies with which CO2 generation is suppressed by means of the catalytic decomposition process. In practice, for such discharged harmful substances as dioxins, PCB and volatile organic compounds (VOC), treating them is the urgent environmental problem, and therefore, the fundamental research was taken up for practical application of the second-generation catalysts of the ultra-violet light and visible light responding type. (NEDO)

  12. FY 2000 Report on the survey results. Survey on international cooperation for medical treatment/welfare equipment; 2000 nendo iryo fukushi kiki kokusai kyodo kenkyu jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The NEDO's representatives visited Europe and China with the objectives of, e.g., international cooperation and information exchanges for medical treatment/welfare equipment. For the welfare equipment technologies, they visited the research institutes and facilities in UK and Germany, among others, to find that the European countries place more emphasis on researches to meet the needs than on advancing the equipment itself. For the medical treatment equipment, they visited the bio-research institutes in Europe for exchanging information on post-genome and tissue engineering. The European countries are behind USA in research fund and manpower for bio-technology and bio-medical, although making great efforts with much expectation on these areas. The China's medical treatment/welfare technologies seem to be clearly still in the stage of needing aids rather than rendering cooperation. However, China has been producing a number of new products in the areas where her traditional arts of medicine are combined with advanced techniques of the West, e.g., those for examination, as felt from a number of the equipment types presented to the China Medical Treatment Equipment Exhibition. (NEDO)

  13. Fiscal 1994 technological survey report. Research study on polymer materials by precision polymerization; 1994 nendo seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    In the paradigm that propelled polymer chemistry, there are involved the establishment of polymer concept, engineering plastics, regulation of higher ordered structure, and precision polymerization. The first two produced the polymer chemistry era in the 20th century. The regulation of higher ordered structure and the precision polymerization are the fundamental technologies supporting the polymer chemistry of the 21st century. The precision polymerization is a technology for regulating the stereospecificity, sequential structure, and molecular weight of polymers by regulating atoms and molecules and is referred to the following important techniques to be concrete. In the precision addition polymerization, stereospecific regulation and purification of active site to give living polymers are required while, in the precision condensation polymerization, regulation of condensation probability process to be secondary Marcov chain is necessary, as is the establishment of non-defect condensation condition avoiding high temperature deterioration and the like. In the biomimetic precision polymerization, key issues are the method of incorporating molecular recognition control and sequential structure control by living organs into an industrial process. If the higher ordered structure can be regulated by the precision polymerization, it is possible to obtain numerous high performance/high functional materials such as superconductors. (NEDO)

  14. Report on the field test project for wind power development at Kamiyaku Town (wind characteristics investigation); Kamiyakucho ni okeru furyoku kaihatsu field test jigyo (fukyo seisa) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-11-01

    Wind characteristics are observed for a year at the above town located at the northern end of the Yakushima island, Kagoshima Prefecture. The exponential index of the wind speed distribution in the vertical direction is 6.06 with all the directions averaged, and is so high as 8.4/13.6 in the wind directions (W/E). Prudence should be exercised, when to estimate the wind speed at the wind turbine hub altitude, against disjunction from the simple exponential law due to geographical peculiarities of the observation location. Turbulence intensity is low and is 0.15 when the wind speed is 2m/s or more, not exerting an ill effect on wind power development. As for the total wind direction occurrence rate on the prevalent wind axis, 78.2% is recorded, which is much higher than the reference value (60%). The average wind speed on this wind axis is high, and this shows that the location is quite suitable for wind power development. The annual average wind speed of 6.3m/s is much higher than the reference value, this again promising a success. The wind energy density of 478W/m{sup 2} is sufficiently high, as compared with the reference value (215W/m{sup 2}). Since there are possibilities of a maximum instantaneous wind speed of over 60m/s, caution is to be used in determining wind endurance for the wind turbine design. The annual capacity ratios for the 150/300/750kW wind turbine models are 33.8/36.5/36.9%, respectively, higher than the NEDO-provided reference value (17% or higher) and predicting sufficient power generation. (NEDO)

  15. Report on the FY 1989 potential survey of overseas coal development. Coal fields in Indonesia; 1989 nendo kaigaitan kaihatsu kanosei chosa hokokusho. Indonesia kyowakoku kaku tanden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-12-01

    This survey is aimed at acquiring the basic data required for judging a possibility of development/import of steam coal in Indonesia (west of Java, north of Sumatra and west of Sumatra). Areas for survey are Meulaboh coal field in north Sumatra, Ombilin III area in West Sumatra, and Bayah coal field in West Java. The survey includes the field survey to grasp the situation of coal seam existence, coal quality, coal amount, etc. and activities for collecting the related data and information from the organizations concerned. The Meulaboh coal field has a technical possibility of open pit mining of medium scale. However, the heating value is extremely low, around 4,300 kcal/kg. Judging from this coal quality, there is no possibility of exporting it. It can be said that Ombilin coal is the world's top class steam coal. Accordingly, the demand can be expected both in export use and domestic use. As to Bayah coal, Bemmelen (1949) concluded that the coal was extremely excellent in quality, but had great disadvantages such as thin coal seam, discontinuity, and complicated geological structure. To date, the conclusion has been unchanged. (NEDO)

  16. Report on the FY 1999 feasibility study for the international joint research in the Asian area. 6; 1999 nendo Asia chiiki kokusai kyodo kenkyu kanosei chosa hokokusho. 6

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper surveyed the situation of the recent economic crisis, social circumstances, trends of energy policies, etc. in Asian countries. The energy consumption in Asian countries mainly including ASEAN countries and China is expected to show a large growth hereinafter together with a rapid economic growth on a long-term basis. Further, the harmony with the environmental problem has been requested. This problem is important also to Japan from a viewpoint of the regional response to the stabilized energy supply/environmental problems. The response to global environmental problems in these countries and the promotion of development/spread of new energy/energy conservation are strongly desired. For the spread of these technologies, it is effective to actually construct/operate/maintain plants under the joint research with Japan from viewpoints of personnel training, technology improvement, PR effects, etc. It is helpful also for Japan from the aspect of technology development such as data acquisition. It is necessary to accurately grasp the needs and technical levels of the other country in the case of carrying out the joint research. The survey was made about 7 countries including Thailand, Indonesia, Malaysia, the Philippines, India, China and Vietnam. (NEDO)

  17. Achievement report for fiscal 1998 on Welfare Technosystem Oita research and development; 1998 nendo Walfare technosystem kenkyu kaihatsu (Oita) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Before a welfare facility is introduced into a home, studies should be sufficiently conducted about the circumstances of daily life, not only of the aged user but also of the family members who take care of the aged user. In the development of handrails, it is found that plastic foam containing wood flour presents the feel of wood, easy to bend when heated. Materials are investigated for flexural strength, and ABS (acrylonitrile butadiene styrene) is chosen as the suitable material. As for devices to assist toileting, a system is developed under which the patient's legs are raised. Since there are arguments for and against the operation itself of mechanically raising a patient's legs, however, efforts will continue to develop much advanced systems. In the study of walk and transfer behavior, a toilet frame mockup is designed and manufactured, which is for collecting data. In an preliminary experiment, tests are conducted about a transfer from a chair to another and, assuming a physically handicapped patient, a transfer from a wheelchair. The data thus collected are to be subjected to analysis and image processing by the use of measuring sensors. Development is described of interfaces, for use in devices to serve as information mediums, which consider the cognition characteristics of the aged people. As for the development of devices for communication, environmental control, and display, their basic operation and feasibility are discussed. Actualities of costumes for physically handicapped people are also investigated, and development is carried out as required. (NEDO)

  18. Fiscal 1999 technical survey report. Basic survey of prioritized fields in Central Asia; 1999 nendo Chuo Asia chiiki juten bun'ya kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For working out and proposing project themes optimum for the popularization of technologies for effectively utilizing energy in four countries in Central Asia (Kazakhstan, Uzbekistan, Turkmenistan, and Azerbaijan), basic surveys were conducted into their energy policies, trends of supply and demand, electric power industry, metal refining industry, and cement making industry. Common to the four nations were that they were rich in energy resources (natural gas, oil, and coal) but that they failed to utilize them effectively despite of an increase in the yields. Incomplete infrastructures and delay in the implementation of energy measures attracted attention. A higher priority was found attached to the upgrading of and investment in structures, renewal of facilities, and the intensification of management. The basic industries wanted the modernization of their facilities and processes. As for electric power consumption, Kazakhstan consumed 53.0-billion kWh, Uzbekistan 39.0-billion kWh, Turkmenistan 4.4-billion kWh, and Azerbaijan 16.4-billion kWh. In Uzbekistan, where the nonferrous metal refining industry led its national economy, the energy consumption rate was found to be quite high. There was a decrease in production in the cement making industry. (NEDO)

  19. Report on investigation in fiscal 2000 of industrial technology exchange with international networking organizations; 2000 nendo kokusaitekina network gata soshiki tono sangyo gijutsu koryu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to promote exchange of industrial technologies, investigations and analyses were made on identification of the current status of networking organizations in different countries working as windows for industrial technology exchange, and on the actual status of technology commercialization methods in overseas incubators. Activities were taken in the following three fields: 1) the current status of networking organizations and incubators in different countries, 2) typology of technology commercialization, technical fields, and success factors, and 3) possibility of the use of technology information in the networking organizations. In Item 1), investigations were performed on the current status and actual activity status of the networking organizations including research parks and individual incubators intended of information exchange, mainly in the United States, UK, and Finland. In Item 2), considerations are given on the points related to technology incubation based on the information about the networking organizations and incubators in each country, and the way the industry-academia cooperation should be. In Item 3), discussions were given on the roles of the networking organizations and the possibility of utilization of technological information in the networking organizations in Japan. (NEDO)

  20. Report for fiscal 1998 by gasification technology subcommittee, Coal Gasification Committee; 1998 nendo sekitan gas ka iinkai gas ka gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The gasification technology subcommittee met on August 4 and November 17, 1998, and on March 10, 1999. Reported for deliberation were the research plan for coal hydrogasification technology development, its progress, and its achievements. On the other hand, the fuel cell-oriented coal gasification subcommittee met on July 23, 1998, and February 26, 1999, when studies were reported for deliberation concerning the development of a coal gasification technology for fuel cells, research plans, and research achievements. Reported in relation to studies using experimenting units were findings acquired using a small test unit, development of an injector, tests using a hot and cold models, development of a cooled char flow extraction technology, development of a highly concentrated powder transportation technology, and conceptual designs of next-generation facilities. A report was also delivered on survey and research on the friendliness toward the community of the development of coal hydrogasification technologies. Furthermore, a plan for reinforcing the system for evaluating the development of coal hydrogasification technologies was brought under deliberation. (NEDO)

  1. Fiscal 1999 report on basic research for promotion of joint implementation programs. Research on energy saving for VSZ ironworks; 1999 nendo VSZ seitetsusho shoene chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The Slovak ironworks is subjected to a survey pursuant to the COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) protocol. A feasibility study is conducted about the installation of important energy saving facilities in the energy consuming sectors which are the coke plant, the sintering plant, and the blast furnace. Considered are CDQ (coke dry quench) and CMC (coal moisture control) for the coke plant, cooler exhaust heat recovery and an ignition burner for the sintering plant, and TRT (top pressure recovery turbine) for the blast furnace. The energy saving effects of CDQ, cooler exhaust heat recovery, ignition burner, and TRT are to be 2269, 183, 227, and 320 TJ/year, respectively, totalling 2999 TJ/year; and their CO2 reduction effects are 218,433, 17,329, 39,537, and 30,263 t-CO2/year, respectively, amounting to 387,349 t-CO2/year including 81,787 t-CO2/year from CMC. The ROI (return of investment) is quite low and is 0.074-0.002, this because of the electricity price being so low as 1/2-1/3 of that in Japan. Further studies including a study of funding are desired because the facilities to be installed will favor the environment and because the currently government controlled special energy price may be raised in the future. (NEDO)

  2. Report on evaluation/selection surveys on coal species, processes and others. Appendix; Tanshu process nado hyoka sentei chosa hokokusho. Furoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report, consisting of 7 chapters, summarizes literature related to liquefaction of coal. Chapter 1 describes the results of the (Project Lignite), i.e., development of the concept of two-stage liquefaction of lignite. Chapter 2 describes the COSTEAM process, which uses synthesis gas (CO-H{sub 2}) as the reducing agent and coal moisture as the hydrogen source for liquefaction of coal of low degree of carbonization, e.g., brown coal. Chapter 3 describes solubilization of coal with alcohol, where coal is reacted with ethanol and NaOH at 300 to 420 degrees C. Chapter 4 describes liquefaction of coal and production of lighter products with tetrahydroquinoline as the hydrogen donor. Chapter 5 describes low-temperature carbonization as the process for liquefying coal, in particular brown coal. Chapter 6 describes possibility of development of new liquefaction techniques for brown coal, including solvolysis for liquefaction, role, recovery and reuse of catalysts, short contact time processes, and coal pretreatment. Chapter 7 describes economic viability of the secondary hydrogenation. (NEDO)

  3. Fiscal 1998 research report. Feasibility study on international cooperation for technology transfer; 1998 nendo chosa hokokusho. Gijutsu iten ni kakawaru kokusai kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    CTI (Climate Technology Initiative) is a framework for use by developed countries in international cooperation and voluntary promotion of the development and diffusion of technologies contributory to reduction of greenhouse gas emissions. The CTI's activity goal is to accelerate the transfer and diffusion of technologies for climate change control. As the first step toward personnel development programs relating to energy efficiency, CTI organized its workshop on that theme. The results of the workshop have been examined, and its achievements were reported at COP4 meeting, while responses by participatory countries were studied to evaluate the potential of international cooperation with regard to personnel development for reducing greenhouse gas emissions. In fiscal 1998, the CTI workshop 'Energy Efficiency' was held. The participants from developing countries understood the necessity and importance of energy saving enough through discussions in the workshop, and announced their message toward the world at COP4 meeting. (NEDO)

  4. Fiscal 1994 survey report. Survey of recent trends in CFC phaseout measures overseas; 1994 nendo shogaikoku ni okeru freon taisaku saishin doko ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Technical literature is referred to for the survey of recent trends in CFC (chlorofluorocarbon) phaseout in various countries overseas. The European Union will totally abolish CFC by the end of 1994 while other developed countries will totally abolish the same by the end of 1995 in compliance with the Montreal protocol. Many of the developing countries are actively striving to reduce CFC use with the help of the Multilateral Fund of Montreal. China and India have production facilities in themselves, and have not announced a phaseout program. There is a proposition for accelerating the regulation of HCFCs (hydrochlorofluorocarbons), but reliable substitutes for them are not yet available and their ozone layer restoring capability if used will be slight. It is feared that such will on the contrary retard CFC phaseout in developing countries. Accordingly, any abrupt acceleration of CFC phaseout implementation is inappropriate. Introduced in this report as fluorine-containing greenhouse gas-related information are a summary of the United Nations Framework Convention on Climate Change and the history of Intergovernmental Panel on Climate Change activities. According to an American survey, the aluminum industry emits 30,000 tons of CF{sub 4} and C{sub 2}F{sub 6}, and the semiconductor manufacturing industry 2,000-3,000 tons. As for SF{sub 6}, 5,000-8,000 tons are emitted mainly by the power industry. Measures for inhibiting them are being taken. (NEDO)

  5. Fiscal 1976 Sunshine Project result report. Research on solar energy utilization systems (photovoltaic power generation); 1976 nendo taiyo energy riyo system chosa kenkyu seika hokokusho. Taiyoko hatsuden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This report describes the fiscal 1976 research result on the technical and economical perspectives of various solar cells, high-efficiency solar cell and its evaluation technique, and a photovoltaic power generation system and its applications. On Si single-crystal slice solar cell, it was pointed out that cost reduction by automatic production process using no vacuum process is essential. On Si thin film solar cell, some problems to be solved for development of particle accelerating growth technique were pointed out. Study was also made on 2-6 group compound semiconductor solar cell, 3-5 group bulk crystal solar cell, 3-5 group thin film solar cell, solar collection solar cell, and raw polycrystal Si materials. On photovoltaic power generation systems, it was reconfirmed through reconsideration of power generation systems for every application that the photovoltaic power generation system for residences is promising. On medium- scale power generation systems, study was made on power load and system configuration in consideration of applications to electric railway, highway, and power source of isolated islands. (NEDO)

  6. Report for fiscal 1981 of Sunshine Program coal group. Basic research on Solvolysis liquefaction technology; 1981 nendo solvolysis ekika gijutsu no kiso kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Basic research is conducted on the Solvolysis liquefaction process for the purpose of producing from coal an ashless, low-sulfur, pollution-free liquid fuel. In the research on the Solvolysis liquefaction (1st stage liquefaction) of coal using a hydrogenation solvent, the Solvolysis liquefaction of coal is studied, for which a refined Solvolysis pitch containing coal substances and a hydride of solvent refined coal are used as Solvolysis liquefaction solvents for the 1st stage. In the research on the 1st stage liquefaction reaction conditions using a high-temperature closed process, two methods are employed. One is a method that uses a mini-pump type reactor in which a small hermetic container is submerged in a high-temperature solvent for rapid heating and the other is a method that uses a pipe type reactor in which coal slurry is caused to travel through a pipe heated to a high temperature. For the analysis of the 2nd stage liquefaction (hydrogenation) reaction conditions, the properties of the 2nd coal liquid, and the constitution of the 2nd coal liquid, and the for the research on the 1st stage liquefaction capacity, the hydrogenation of anthracene oil and solvent refined coal as recyclable solvent models is studied. (NEDO)

  7. Report on the achievements in the Sunshine Project in fiscal 1986. Surveys on coal type selection (coal type survey); 1986 nendo tanshu sentei chosa seika hokokusho. Tanshu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    The purpose of the present study is to elucidate coal quality features of different types of coals and identify the relationship between the coal quality features and the liquefaction characteristics by performing liquefaction characteristic evaluation tests. Based on the result therefrom, a method is established for coal field assessment that can estimate yield of liquefaction in coal fields and coal mines to serve for selection of coal types suitable for liquefaction. Coal quality feature surveys and liquefaction characteristics evaluation tests under the standard conditions have been completed on 48 coal types including Canadian, Australian and American coals. Elucidating the coal quality features of different coals can specify parameters for the coal quality features related to the liquefaction characteristics. Coal ranks elucidate the vitrinite reflectance, structure constituent factors the vitrinite content, composite factors the volatile matter content, quantity of heat generation, and number of H/C and O/C atoms. Investigating the relationship between the coal quality features and the liquefaction characteristics can provide fundamental data for primary screening of raw material coals for liquefaction. The result of the liquefaction characteristics evaluation test under the standard conditions can be the detailed comparative data relative to data derived from the simplified liquefaction characteristics test that is performed to estimate liquefaction yield of specific coal field and coal mine. (NEDO)

  8. Report on 1981 result of Sunshine Project. Research on direct liquefaction reactor of coal; 1981 nendo sekitan no chokusetsu ekika hannoki no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-07-01

    This paper explains the results of research on direct liquefaction reaction of coal in fiscal 1981. The direct liquefaction is a reaction of three phases, gas-liquid-solid, under high temperature and high pressure. A tube type was employed in order to increase volume efficiency of the reactor, the continuous phase disperse number was decreased in order to bring it close to plug flow, and the paste Re number was increased to some extent in order to prevent sedimentation of coal particles. Hydrogen was supplied from the tube halfway for the purpose of supplementing the lowering of hydrogen partial pressure with the progress of reaction. A gas-liquid separator was installed so that increase in gas quantity was controlled in the rear stage of the reactor. As for catalysts, iron ore-sulfur system was examined which was promising as a disposable catalyst in place of the conventional iron system. Effect of catalytic addition was clearly recognizable in comparison with non-catalytic, with an exothermic peak observed comparable to the coal hydrogenation reaction of 350-420 degree C. Its catalytic effect was also presumable from the high pressure differential thermal analysis curve. The catalytic mechanism in the case where sulfur is added to hematite and limonite is similar to that of Fe{sub 2}O{sub 3} - sulfur catalyst, with the center of activity supposed to be Fe{sub 1-x}S. The catalytic effect is largely dependent on the particle size. (NEDO)

  9. Sunshine Program for fiscal 1981. Research on direct coal-liquefaction reactor; 1981 nendo sekitan chokusetsu ekika hannoki no kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-04-17

    The research aims to develop a new-type high-efficiency reactor for direct coal-liquefaction from a reaction engineering viewpoint and, at the same time, to settle problems expected to occur in industrializing this technique. The research items are Item 1 on the analysis of characteristics of a tubular continuous reactor and Item 2 on high-activity catalysts. Under Item 1, on the assumption that liquefaction reaction is dominantly a reaction in a continuous phase, a reactor is selected in consideration of homogeneous-phase reaction, and operating conditions are set according to the selected reactor and to the liquefaction reaction characteristics. A somewhat large Re number is assigned to the paste. Since the hydrogen partial pressure lowers with the progress of reaction, hydrogen is resupplied at the middle of the reaction tube. The volume of gas increases toward the final stage of reaction, decreasing the continuous phase holdup. Since it is undesirable to let the decrease stand, a vapor-liquid separator is provided for the control of the gas volume. In this fiscal year, investigation is conducted into details so as to determine if the reactor is equipped with intended characteristics. Under Item 2, the iron ore is deemed to be the most promising as disposal catalysts for liquefaction. In this fiscal year, studies are conducted to disclose the activity etc. of catalysts of this type. (NEDO)

  10. Survey report for fiscal 1981 of 3rd subcommittee of Coal Gasification Committee; 1981 nendo sekitan gasu ka iinkai dai 3 bukai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Survey and research are conducted to grasp the current status of the development of the coal gasification combined power cycle generation technology, in which the coal gasification technology and the combined power cycle generation technology are combined, and to clarify the relevant tasks to be discharged. The latest information on the coal gas direct combustion system and fuel cell system is also compiled into this report. Although coal is abundant all the world over, yet Japan has to import it. It is afraid that the coal to be imported will be diverse in property and that the use will increase of coal inferior in quality with much ash and moisture. As for gasification furnaces, efforts of development are concentrated on the fluidized bed type and entrained bed type, both of which will have to deal with various kinds of coal, to be large in capacity, high in gasification efficiency, and excellent in serviceability. As for cleaning-up systems, the dry type is advantageous in terms of thermal efficiency, but it needs to be verified for refining capacity and serviceability. When it comes to gas turbines, efforts need to be started at an early date for developing a high-temperature/high-pressure gas turbine which is fueled with coal gas. Since the development of an integrated coal gasification combined cycle power generation plant demands enormous amounts of funds, a check-and-review process is indispensable for each development stage. (NEDO)

  11. FY 1993 Research and development of advanced ceramic gas turbines. Researches on social adaptability; 1993 nendo senshingata ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Shakai tekigosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    The ceramic gas turbines (CGT's) for, e.g., cogeneration and portable power generation systems are studied and evaluated for their environmental preservation, energy saving and economic characteristics. Types of utilization and market sizes are also studied for, e.g., portable power generation systems. The items studied include current status of cogeneration systems in USA, and recognition of cogeneration systems in Japan. The study results lead to the conclusions that the biaxial CGT for portable power generation systems is a promising substitute for diesel engines as the power source in the future, and 300kW class CGT's will have the markets of 170,000 units and potentially 450,000 units, because of their expected wide applicability. The studies on their economic, energy-saving and environmental load reduction effects indicate that one unit brings the economic effects totaling 616,000 yen, due to reduced fuel consumption and NOx abatement. They could reduce NOx emissions by 8,090 t/y for automobiles and 6,570 t/y for the others, when they fill the potential markets. (NEDO)

  12. International symposium on environmental impacts of advanced alternative to CFC; CFC shinki daitai busshitsu no kankyo eikyo ni kansuru kokusai symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-07

    The international symposium on environmental effects of new CFC substitutes was held in Tsukuba City, Ibaraki Pref. on February 7-9, 1996, and 19 papers were made public. In Session 1 (Plenary lecture), reports were made on Global warming and climate change: a review of recent studies; Stratospheric ozone, CFCs, and CFC-substitutes: an update, etc. In Session 2, Measurements of OH rate constants for advanced refrigerants as well as HCFCs and HFCs; The reaction rate of CFC alternatives with OH radical; Experimental and estimated rate constants: reactions of hydroxyl radicals with several halocarbons, etc. In Session 3, Measurement of uptake coefficients of some acetyl halides and fluorinated ethers into water; Mass transfer at the air/water interface: removal processes of halocarbonyl compounds; Heterogeneous reactions of fluorinated ethers on allophane or titanium dioxide, etc. In Session 4, papers were reported on model calculations relating to the global warming.

  13. Fiscal 1999 survey report on Jozankei Hot Spring conservation (3rd phase); 1999 nendo Jozankei onsen hozen chosa hokokusho (dai sanji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-11-01

    The impact of geothermal exploitation in the Yunosawa district on the Jozankei hot spring and others in the neighborhood was evaluated, and a survey was conducted of the formation and eruption mechanisms of the Jozankei hot spring for the purpose of hot spring conservation. Activities were conducted in the three fields of (1) geological structure analysis, (2) geochemical analysis of fluids, and (3) comprehensive analysis. Conducted in field (2) were analysis of hot spring utilization data and the contents, analysis of hot spring water and geothermal water, analysis of fluctuations in hot springs, and fluid movement models. Studied in field (3) were the outline of large area geothermal systems, geothermal structure models, relations between geothermal reservoirs and hot spring aquifers, and impact of geothermal exploitation on hot springs. Disclosed as the result were hot spring geological structure models, formation mechanism, eruption mechanism, origins of hot spring water, fluid movement models, interference between hot spring units, and changes in the hot springs as a whole. It was then concluded that the geothermal exploitation in the Yunosawa district would not exert any impact on the hot springs. (NEDO)

  14. Fiscal 1999 survey report on introducing technique for predicting impact on hot spring; 1999 nendo onsen eikyo yosoku shuho donyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-10-01

    For the application of fruits of the geothermal development promotion project to survey phase C and for the study of technical means for appropriate development to employ after phase C, some cases of impacts imposed on hot springs by geothermal development were taken up and the causes of the impacts were investigated. Activities were conducted in the three fields of (1) the survey of actualities of impacts imposed on hot springs, (2) the survey of the causes of such impacts, and (3) a comprehensive survey. Keyword searches were conducted into the data system and geothermal energy related magazines, and 13 cases were found in which hot springs were affected by geothermal development, which included the Palinpinon district (Philippines), the Koso district (America), and the Wairakei district (New Zealand). Concerning the 13 cases, data on geology, geological structures, and geothermal fluids were collected and studies were conducted about relations of geothermal development with geological structures and geothermal fluids, as in the case of hot springs, and the two were integrated for the clarification of the causes of impacts. In concluding the report, the difference in mechanism is deliberated between cases with impacts on hot springs and cases without impacts on hot springs. (NEDO)

  15. Fiscal 1976 Sunshine Project result report. Research on solar energy system (weather survey); 1976 nendo taiyo energy system no kenkyu seika hokokusho. Kisho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-31

    This report describes the fiscal 1976 research result on weather survey for solar energy systems. Study was made on preparation of the global solar radiation (GSR) map of Japan. To obtain the estimation equation of GSR based on related weather data, analysis was made on data at A type GSR observation sites and related weather data. As some factors effective for estimating monthly mean GSR, a relative sunshine duration, snowfall index (ratio of days more than 10cm in snowfall) and solar altitude index (sine of solar altitude at culmination hour) were selected. The estimation equation was prepared on the basis of these above factors. GSR was affected by relative sunshine duration exceedingly, snowfall by 12%, and solar altitude difference by 6% within an error of 5%. The monthly and annual GSR maps were prepared every site by the above calculation. The continuous observation results in Kagoshima and Fukuoka by recording direct pyranometers are presented. Scattered solar radiation is defined as the difference between simultaneously measured GSR and direct solar radiation. Weather data preparation in Fukuoka for design of solar cooling/heating and hot water supply systems is also described. (NEDO)

  16. Report on evaluation concerning R and D of magneto hydrodynamic (MHD) generation. Introduction; Denji ryutai (MHD) hatsuden no kenkyu kaihatsu ni kansuru hyoka hokokusho. Soron

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    Evaluation was conducted concerning R and D on magneto hydrodynamic (MHD) generation, with proposals made for the future R and D. As a result of the experimental operation and studies of the Mark 7 machine for MHD generation, a cold wall type generation channel was found promising in the long-term durability under MHD generation conditions. In addition, R and D was conducted on the exhaust gas control system that fulfilled an environmental standard, seed recovery method, grasp of seed coagulation state, etc. The R and D on element technologies were carried out along with the R and D of the Mark 7 and played a role in the backup of its experiment. MHD generation presents a large number of attractive characteristics, with its development expected in the future. However, it seems too early to immediately move on to the next step. Examinations should be made on such matters as comparisons with various kinds of new power generation systems using coal, trends in foreign countries particularly the U-500 project of the Soviet Union, the ideal system for more efficient development, and possibility of international cooperation. (NEDO)

  17. Achievement report on research and development in the Sunshine Project in fiscal 1977. Hydrogen energy; 1977 nendo seika hokokusho gaiyoshu. Suiso energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-04-01

    This paper summarizes achievements in the Sunshine Project related to hydrogen energy in fiscal 1977. In the electrolytic process in hydrogen manufacturing technologies, new composite materials are developed in relation with membranes and electrodes as the high temperature and pressure water decomposition method. A bench-scale water decomposition tank using organic polymer ion exchange membranes is fabricated on a trial basis and tested for studying solid electrolyte decomposition method. In hydrogen manufacturing technologies using thermo-chemical process, discussions are being given on cycles of iron systems, iodine systems and hybrid systems (mixture of thermo and photo chemistry and electrochemistry). For hydrogen transporting and storing technologies, metal hydrides most suitable for hydrogen storage are developed, and storage systems are studied. In hydrogen combustion, elucidation is made on fundamental conditions for mixed and single combustion technologies suitable for prevention of reverse ignition and suppression of NOx generation. Studies are also being made on fuel cells using aqueous solution and solid electrolytes. Studies on hydrogen fueled engines are also described. In hydrogen safety assuring technologies, discussions are being given on prevention of explosion disasters, prevention of embrittlement of materials due to hydrogen and criteria for safety assuring technologies. Descriptions are given also on studies on total hydrogen energy systems and hydrogen fueled automobiles. (NEDO)

  18. Report on the FY 1982 potential survey of overseas coal development. Coal fields in Mexico; 1982 nendo kaigaitan kaihatsu kanosei chosa hokokusho. Mexico kaku tanden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-10-01

    The following surveys were made to acquire the data/information for potential study of development/import of Mexican coal: (1) collection of general information such as energy situation, coal situation and infrastructure. (2) survey of situation of coal seam existence, coal quality, coal amount, exploration/development, etc. of Sabinas coal field, Monclova, Coahuila state, San Marcial coal field, San Enrique, Sonora state, and Tezoatlan coal field, Tlaxiaco, Oaxaca state. (3) data collection for potential study of future development. The area where coal is presently produced is only Coahuila state, and also there the exploration is comparatively being advanced. In states of Sonora and Oaxaca, the exploration is only made roughly by CRM, and the exploration is going to be detailedly made from now. The exploration in Coahuila state, however, was made only down to 400m under earth's surface. In this area, coal existence down to 1,000m under earth's surface is expected, and the exploration deeper than 400m is a future subject. Ninty percent of the present coal reserve is produced from Coahuila state. They are coking coal and steam coal in quality. At present, the Mexican government is exerting efforts to increase production of the domestic use coal, with no intention of exporting coal. Seeing how the exploration would go, it is necessary to watch the results of the survey on a long-term basis. (NEDO)

  19. Fiscal 2000 research achievement report. Super-advanced electronics technologies development promotion project; 2000 nendo kenkyu seika hokokusho. Cho sentan gijutsu kaihatsu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-05-01

    For the construction of a common base of key technologies in the domain of electronics and information with the influence propagating across a wide range of industries, research and development was conducted of technologies of ultrafine working process, technologies of ultimate measurement, analysis, and control, technologies of new functional electronic materials, etc. Studied in the field of electron beam lithography were high precision and large area imaging technology, highly accurate electron optics control system technology, and beam monitoring technology. Studied in the field of ultrashort wavelength electromagnetic wave patterning system technology were proximity ultrashort wavelength electromagnetic wave patterning system technology, reduced ultrashort wavelength electromagnetic wave patterning system technology, and ultrahigh precision new materials patterning technology. Also studied were technologies of super-advanced plasma measurement, analysis, and control, and technology of super-advanced cleaning. In the field of technologies of new functional elements and films, studies were conducted about technologies of highly sensitive GMR (giant magnetoresistive) film and head fabrication process for contact magnetic recording and technologies of a spin-valve head with submicron track width for contact magnetic recording. (NEDO)

  20. Fiscal 1999 survey report. Survey of feasibility of international cooperation in the transfer of technology; 1999 nendo gijutsu iten ni kakawaru kokusai kyoryoku kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Among the activity goals of CTI (climate technology initiative), which is a framework designed to encourage international cooperation of leading nations in the voluntary development and diffusion of technologies supposed to contribute to the reduction of greenhouse gas emissions, there is the promotion of the transfer and diffusion of climate change preventing technologies. To achieve the goal, energy efficiency oriented workshops will be held as part of the training for the raising of people skilled in energy saving, the results will be examined, the achievements attained at such events will be introduced at COP5 (Conference of the Parties at Bonn), and the responses of the respective countries will be reviewed, all these for the investigation of the feasibility of international cooperation for raising people dedicated to the reduction of greenhouse gas emission. In this fiscal year, aiming to make clear the possibility of contribution to the transfer of software-related technologies through cooperation of multiple nations, lecturers from leading countries and participants from developing nations met, held a workshop over energy efficiency technologies, and the results were compiled. (NEDO)