WorldWideScience

Sample records for highly deformed 75kr

  1. High-spin states in 75Kr

    Science.gov (United States)

    Chishti, A. A.; Gelletly, W.; Lister, C. J.; Mcneill, J. H.; Varley, B. J.; Love, D. J. G.; Skeppstedt, O.

    1989-09-01

    Levels in the 75Kr nucleus were populated in the inverse 24Mg( 54Fe, 2pn) 75Kr reaction at beam energies of 177 and 190 MeV. In the reaction study at 177 MeV, the γ-rays were detected in coincidence with neutrons and mass-75 nuclei and in the reaction at 190 MeV only γγ-coincidence data were collected. Using the γγ-neutron gated γγ- and Recoil-γγ-coincidence techniques, we were able to develop the level scheme up to spins ( {37+}/{2}) and ( {31-}/{2}) in the positive- and negative-parity bands, respectively. These spins are high enough to allow us to study alignment effects in this mass region. The signature splitting at low spin can be reproduced in a cranked shell model calculation assuming a quadrupole deformation β2 = 0.37 and a slightly triaxial ( γ≈ -10°) shape for positive-parity states but an axial shape for the negative-parity sequence. The spin alignment as a function of rotational frequency has been studied; in the positive-parity band alignment is observed at a rotational frequency of h̵ω ≈ 0.63 MeV and in the negative-parity band the alignment occurs at h̵ω ≈ 0.57 MeV. The observed alignment in both bands is associated with a pair of g{9}/{2} protons, and the difference in the alignment frequencies is thought to be due to differing intrinsic shapes.

  2. Lifetime measurement of high spin states in {sup 75}Kr

    Energy Technology Data Exchange (ETDEWEB)

    Trivedi, T. [Department of Physics, University of Allahabad, Allahabad-211001 (India); Palit, R. [Tata Institute of Fundamental Research, Mumbai-400005 (India); Negi, D. [Inter University Accelerator Centre, New Delhi-110067 (India); Naik, Z. [Tata Institute of Fundamental Research, Mumbai-400005 (India); Yang, Y.-C. [Department of Physics, Shanghai Jiao Tong University, Shanghai 200240 (China); Sun, Y. [Department of Physics, Shanghai Jiao Tong University, Shanghai 200240 (China); Department of Physics and Astronomy, University of Tennessee, Knoxville, TN 37996 (United States); Sheikh, J.A. [Department of Physics and Astronomy, University of Tennessee, Knoxville, TN 37996 (United States); Physics Division, Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831 (United States); Department of Physics, University of Kashmir, Srinagar 190 006 (India); Dhal, A. [Department of Physics, Banaras Hindu University, Varanasi 221005 (India); Raju, M.K. [Department of Nuclear Physics, Andhra University, Visakhapatnam-530003 (India); Appannababu, S. [Department of Physics, MS University of Baroda, Vadodara-390002 (India); Kumar, S. [Department of Physics and Astrophysics, University of Delhi, Delhi-110007 (India); Choudhury, D. [Department of Physics, IIT Roorkee, Roorkee-247667 (India); Maurya, K. [Department of Physics, University of Allahabad, Allahabad-211001 (India); Mahanto, G.; Kumar, R.; Singh, R.P.; Muralithar, S. [Inter University Accelerator Centre, New Delhi-110067 (India); Jain, A.K. [Department of Physics, IIT Roorkee, Roorkee-247667 (India); Jain, H.C. [Tata Institute of Fundamental Research, Mumbai-400005 (India); Pancholi, S.C. [Inter University Accelerator Centre, New Delhi-110067 (India)

    2010-03-01

    The lifetimes of high spin states of {sup 75}Kr have been determined via {sup 50}Cr ({sup 28}Si, 2pn) {sup 75}Kr reaction in positive parity band using the Doppler-shift attenuation method. The transition quadrupole moments Q{sub t} deduced from lifetime measurements have been compared with {sup 75}Br. Experimental results obtained from lifetime measurement are interpreted in the framework of projected shell model.

  3. Highly deformable nanofilaments in flow

    Science.gov (United States)

    Pawłowska, S.

    2016-10-01

    Experimental analysis of hydrogel nanofilaments conveyed by flow is conducted to help in understanding physical phenomena responsible for transport properties and shape deformations of long bio-objects, like DNA or proteins. Investigated hydrogel nanofilaments exhibit typical macromolecules-like behavior, as spontaneous conformational changes and cross-flow migration. Results of the experiments indicate critical role of thermal fluctuations behavior of single filaments.

  4. High Resolution Silicon Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal describes a plan to build a prototype small stroke, high precision deformable mirror suitable for space-based operation in systems for high-resolution...

  5. Highly deformable bones: unusual deformation mechanisms of seahorse armor.

    Science.gov (United States)

    Porter, Michael M; Novitskaya, Ekaterina; Castro-Ceseña, Ana Bertha; Meyers, Marc A; McKittrick, Joanna

    2013-06-01

    Multifunctional materials and devices found in nature serve as inspiration for advanced synthetic materials, structures and robotics. Here, we elucidate the architecture and unusual deformation mechanisms of seahorse tails that provide prehension as well as protection against predators. The seahorse tail is composed of subdermal bony plates arranged in articulating ring-like segments that overlap for controlled ventral bending and twisting. The bony plates are highly deformable materials designed to slide past one another and buckle when compressed. This complex plate and segment motion, along with the unique hardness distribution and structural hierarchy of each plate, provide seahorses with joint flexibility while shielding them against impact and crushing. Mimicking seahorse armor may lead to novel bio-inspired technologies, such as flexible armor, fracture-resistant structures or prehensile robotics.

  6. High Resolution Silicon Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this proposal we describe a plan to build a deformable mirror suitable for space-based operation in systems for high-resolution imaging. The prototype DM will be...

  7. Liquid Droplets on a Highly Deformable Membrane

    Science.gov (United States)

    Schulman, Rafael D.; Dalnoki-Veress, Kari

    2015-11-01

    We examine the deformation produced by microdroplets atop thin elastomeric and glassy free-standing films. Because of the Laplace pressure, the droplets deform the elastic membrane thereby forming a bulge. Thus, two angles define the droplet or membrane geometry: the angles the deformed bulge and the liquid surface make with the film. These angles are measured as a function of the film tension, and are in excellent agreement with a force balance at the contact line. Finally, we find that if the membrane has an anisotropic tension, the droplets are no longer spherical but become elongated along the direction of high tension.

  8. Liquid Droplets on a Highly Deformable Membrane

    Science.gov (United States)

    Schulman, Rafael; Dalnoki-Veress, Kari

    2015-11-01

    We present measurements of the deformation produced by micro-droplets atop thin elastomeric and glassy free-standing films. Due to the Laplace pressure, the droplets deform the elastic membrane thereby forming a bulge. Thus, there are two angles that define the droplet/membrane geometry: the angle the liquid surface makes with the film and the angle the deformed bulge makes with the film. The contact line geometry is well captured by a Neumann construction which includes contributions from interfacial and mechanical tensions. Finally, we show that a droplet atop a film with biaxial tension assumes an equilibrium shape which is elongated along the axis of high tension.

  9. High strain rate deformation of layered nanocomposites

    Science.gov (United States)

    Lee, Jae-Hwang; Veysset, David; Singer, Jonathan P.; Retsch, Markus; Saini, Gagan; Pezeril, Thomas; Nelson, Keith A.; Thomas, Edwin L.

    2012-11-01

    Insight into the mechanical behaviour of nanomaterials under the extreme condition of very high deformation rates and to very large strains is needed to provide improved understanding for the development of new protective materials. Applications include protection against bullets for body armour, micrometeorites for satellites, and high-speed particle impact for jet engine turbine blades. Here we use a microscopic ballistic test to report the responses of periodic glassy-rubbery layered block-copolymer nanostructures to impact from hypervelocity micron-sized silica spheres. Entire deformation fields are experimentally visualized at an exceptionally high resolution (below 10 nm) and we discover how the microstructure dissipates the impact energy via layer kinking, layer compression, extreme chain conformational flattening, domain fragmentation and segmental mixing to form a liquid phase. Orientation-dependent experiments show that the dissipation can be enhanced by 30% by proper orientation of the layers.

  10. High temperature deformation of silicon steel

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez-Calvillo, Pablo, E-mail: pablo.rodriguez@ctm.com.es [CTM - Technologic Centre, Materials Technology Area, Manresa, Cataluna (Spain); Department of Materials Science and Metallurgical Engineering, Universidad Politecnica de Cataluna, Barcelona (Spain); Houbaert, Yvan, E-mail: Yvan.Houbaert@UGent.be [Department of Materials Science and Engineering, University of Ghent (Belgium); Petrov, Roumen, E-mail: Roumen.Petrov@ugent.be [Department of Materials Science and Engineering, University of Ghent (Belgium); Kestens, Leo, E-mail: Leo.kestens@ugent.be [Department of Materials Science and Engineering, University of Ghent (Belgium); Colas, Rafael, E-mail: rafael.colas@uanl.edu.mx [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon (Mexico); Centro de Innovacion, Investigacion y Desarrollo en Ingenieria y Tecnologia, Universidad Autonoma de Nuevo Leon (Mexico)

    2012-10-15

    The microstructure and texture development during high temperature plane strain compression of 2% in weight silicon steel was studied. The tests were carried out at a constant strain rate of 5 s{sup -1} with reductions of 25, 35 and 75% at temperatures varying from 800 to 1100 Degree-Sign C. The changes in microstructure and texture were studied by means of scanning electron microscopy and electron backscattered diffraction. The microstructure close to the surface of the samples was equiaxed, which is attributed to the shear caused by friction, whereas that at the centre of the specimens was made of a mixture of elongated and fine equiaxed grains, the last ones attributed to the action of dynamic recovery followed by recrystallization. It was found that the volume fraction of these equiaxed grains augmented as reduction and temperature increased; a 0.7 volume fraction was accomplished with a 75% reduction at 1100 Degree-Sign C. The texture of the equiaxed and elongated grains was found to vary with the increase of deformation and temperature, as the {gamma}-fibre tends to disappear and the {alpha}-fibre to increase towards the higher temperature range. -- Highlights: Black-Right-Pointing-Pointer The plastic deformation of a silicon containing steel is studied by plane strain compression. Black-Right-Pointing-Pointer Equiaxed and elongated grains develop in different regions of the sample due to recrystallization. Black-Right-Pointing-Pointer Texture, by EBSD, is revealed to be similar in either type of grains.

  11. Twinning in copper deformed at high strain rates

    Indian Academy of Sciences (India)

    S Cronje; R E Kroon; W D Roos; J H Neethling

    2013-02-01

    Copper samples having varying microstructures were deformed at high strain rates using a split-Hopkinson pressure bar. Transmission electron microscopy results show deformation twins present in samples that were both annealed and strained, whereas samples that were annealed and left unstrained, as well as samples that were unannealed and strained, are devoid of these twins. These deformation twins occurred at deformation conditions less extreme than previously predicted.

  12. Dynamic shear deformation in high purity Fe

    Energy Technology Data Exchange (ETDEWEB)

    Cerreta, Ellen K [Los Alamos National Laboratory; Bingert, John F [Los Alamos National Laboratory; Trujillo, Carl P [Los Alamos National Laboratory; Lopez, Mike F [Los Alamos National Laboratory; Gray, George T [Los Alamos National Laboratory

    2009-01-01

    The forced shear test specimen, first developed by Meyer et al. [Meyer L. et al., Critical Adiabatic Shear Strength of Low Alloyed Steel Under Compressive Loading, Metallurgical Applications of Shock Wave and High Strain Rate Phenomena (Marcel Decker, 1986), 657; Hartmann K. et al., Metallurgical Effects on Impact Loaded Materials, Shock Waves and High Strain rate Phenomena in Metals (Plenum, 1981), 325-337.], has been utilized in a number of studies. While the geometry of this specimen does not allow for the microstructure to exactly define the location of shear band formation and the overall mechanical response of a specimen is highly sensitive to the geometry utilized, the forced shear specimen is useful for characterizing the influence of parameters such as strain rate, temperature, strain, and load on the microstructural evolution within a shear band. Additionally, many studies have utilized this geometry to advance the understanding of shear band development. In this study, by varying the geometry, specifically the ratio of the inner hole to the outer hat diameter, the dynamic shear localization response of high purity Fe was examined. Post mortem characterization was performed to quantify the width of the localizations and examine the microstructural and textural evolution of shear deformation in a bcc metal. Increased instability in mechanical response is strongly linked with development of enhanced intergranular misorientations, high angle boundaries, and classical shear textures characterized through orientation distribution functions.

  13. Damage evolution of metallic materials during high temperature plastic deformation

    Institute of Scientific and Technical Information of China (English)

    汪凌云; 刘雪峰; 汤爱涛; 黄光杰

    2002-01-01

    The damage evolution of high temperature plastic deformation of metallic materials was studied by use of continuum damage mechanics (CDM) theory. Based on thermodynamics, on a damage variable D and Zener-Hollomon parameter Z, and on the effective stress concept, a damage evolution model of high temperature plastic deformation was derived and was used to analyze the damage evolution of 1420 Al-Li alloy during high temperature plastic deformation. The model that is verified by tests can also be applied to the materials that are loaded prorata or out of proportion during high temperature plastic deformation. It extends the applied scope of damage mechanics.

  14. Transition in Deformation Mechanism of AZ31 Magnesium Alloy during High-Temperature Tensile Deformation

    Directory of Open Access Journals (Sweden)

    Masafumi Noda

    2011-01-01

    Full Text Available Magnesium alloys can be used for reducing the weight of various structural products, because of their high specific strength. They have attracted considerable attention as materials with a reduced environmental load, since they help to save both resources and energy. In order to use Mg alloys for manufacturing vehicles, it is important to investigate the deformation mechanism and transition point for optimizing the material and vehicle design. In this study, we investigated the transition of the deformation mechanism during the high-temperature uniaxial tensile deformation of the AZ31 Mg alloy. At a test temperature of 523 K and an initial strain rate of 3×10−3 s-1, the AZ31 Mg alloy (mean grain size: ~5 μm exhibited stable deformation behavior and the deformation mechanism changed to one dominated by grain boundary sliding.

  15. Measuring High Speed Deformation for Space Applications

    Science.gov (United States)

    Wentzel, Daniel

    2014-01-01

    PDV (Photonic Doppler Velocimetry) has proven to be a reliable and versatile technique to observe rapid deformation of frangible joints. It will be a valuable technique in order to understand the physics of two-stage light gas guns and the material response to hypervelocity impact.

  16. Design of deformable mirrors for high power lasers

    Institute of Scientific and Technical Information of China (English)

    Stefano Bonora; Jan Pilar; Antonio Lucianetti; Tomas Mocek

    2016-01-01

    We present the workflow of the design, realization and testing of deformable mirrors suitable for high power diode pumped solid-state lasers. It starts with the study of the aberration to be corrected, and then it continues with the design of the actuators position and characteristic. In this paper, we present and compare three deformable mirrors realized for multi-J level laser facilities. We show that with the same design concept it is possible to realize deformable mirrors for other types of lasers. As an example, we report the realization of a deformable mirror for femtosecond lasers and for a CW CO2 laser.

  17. Effect of Purity Levels on the High-Temperature Deformation Characteristics of Severely Deformed Titanium

    Science.gov (United States)

    Sajadifar, Seyed Vahid; Yapici, Guney Guven

    2017-03-01

    In the present investigation, high-temperature compression tests were conducted at strain rates of 0.001 to 0.1 s-1 and at temperatures of 873 K to 1173 K (600 °C to 900 °C) in order to study the hot deformation characteristics and dynamic softening mechanisms of two different grades of commercial purity titanium after severe plastic deformation. It was observed that the effects of deformation rate and temperature are significant on obtained flow stress curves of both grades. Higher compressive strength exhibited by grade 2 titanium at relatively lower deformation temperatures was attributed to the grain boundary characteristics in relation with its lower processing temperature. However, severely deformed grade 4 titanium demonstrated higher compressive strength at relatively higher deformation temperatures (above 800 °C) due to suppressed grain growth via oxygen segregation limiting grain boundary motion. Constitutive equations were established to model the flow behavior, and the validity of the predictions was demonstrated with decent agreement accompanied by average error levels less than 5 pct for all the deformation conditions.

  18. Deformation Twinning of a Silver Nanocrystal under High Pressure

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Xiaojing; Yang, Wenge; Harder, Ross; Sun, Yugang; Liu, Ming; Chu, Yong S.; Robinson, Ian K.; Mao, Ho-kwang

    2015-11-01

    Within a high-pressure environment, crystal deformation is controlled by complex processes such as dislocation motion, twinning, and phase transitions, which change materials' microscopic morphology and alter their properties. Understanding a crystal's response to external stress provides a unique opportunity for rational tailoring of its functionalities. It is very challenging to track the strain evolution and physical deformation from a single nanoscale crystal under high-pressure stress. Here, we report an in situ three-dimensional mapping of morphology and strain evolutions in a single-crystal silver nanocube within a high-pressure environment using the Bragg Coherent Diffractive Imaging (CDI) method. We observed a continuous lattice distortion, followed by a deformation twining process at a constant pressure. The ability to visualize stress-introduced deformation of nanocrystals with high spatial resolution and prominent strain sensitivity provides an important route for interpreting and engineering novel properties of nanomaterials.

  19. Inelastic deformation and damage at high temperature

    Science.gov (United States)

    Krempl, E.

    1992-06-01

    Combined experimental and theoretical investigations into the inelastic deformation and damage behavior of engineering alloys at elevated temperatures are being pursued. The analysis of previously performed strain rate change and relaxation tests on modified 9Cr-1Mo steel showed the need for inclusion of a recovery of state term in the growth laws for the state variables of the viscoplasticity theory based on overstress (VBO). Recovery of state terms were introduced and the experimental results were satisfactorily simulated. The finite deformation theory of VBO has been developed further to include a convected derivative rationale for the choice of the objective stress rate. The reversing direct current voltage drop measurements during low cycle fatigue at elevated temperature were improved. A passive filter bank and new positioning devices for the coils were installed. Tests at 650 C and lasting several days showed excessive, uncontrollable temperature changes. It was decided to drop the test temperature to 538 C which is close to the operating temperature of type 304 stainless steel. The temperature fluctuations in torsion tests were within +/- 3 C which was considered satisfactory.

  20. Inelastic deformation and damage at high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Krempl, E.

    1992-01-01

    Combined experimental and theoretical investigations into the inelastic deformation and damage behavior of engineering alloys at elevated temperatures are being pursued. The analysis of previously performed strain rate change and relaxation tests on modified 9Cr-1Mo steel showed the need for inclusion of a recovery of state term in the growth laws for the state variables of the viscoplasticity theory based on overstress (VBO). Recovery of state terms were introduced and the experimental results were satisfactorily simulated. The finite deformation theory of VBO has been developed further to include a convected derivative rationale for the choice of the objective stress rate. The reversing direct current voltage drop measurements during low cycle fatigue at elevated temperature were improved. A passive filter bank and new positioning devices for the coils were installed. Tests at 650{degrees}C and lasting several days showed excessive, uncontrollable temperature changes. It was decided to drop the test temperature to 538{degrees}C which is close to the operating temperature of Type 304 Stainless Steel. The temperature fluctuations in torsion tests were within {plus minus}3{degrees}C which was considered satisfactory. Testing will continue at 538{degrees}C.

  1. Dynamic tensile behaviour and deformational mechanism of C5191 phosphor bronze under high strain rates deformation

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Dao-chun [College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016 (China); College of Mechanical and Electrical Engineering, Taizhou Vocational & Technical College, Taizhou 318000 (China); Chen, Ming-he, E-mail: meemhchen@nuaa.edu.cn [College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016 (China); Wang, Lei; Cheng, Hu [College of Mechanical Engineering, Taizhou University, Taizhou 318000 (China)

    2016-01-01

    High speed stamping process is used to high strength and high electrical conductivity phosphor bronze with extremely high strain rates more than 10{sup 3} s{sup −1}. This study on the dynamic tensile behaviour and deformational mechanism is to optimise the high speed stamping processes and improve geometrical precision in finished products. Thus, the tensile properties and deformation behaviour of C5191 phosphor bronze under quasi-static tensile condition at a strain rate of 0.001 s{sup −1} by electronic universal testing machine, and dynamic tensile condition at strain rate of 500, 1000 and 1500 s{sup −1} by split Hopkinson tensile bar (SHTB) apparatus were studied. The effects of strain rate and the deformation mechanism were investigated by means of SEM and TEM. The results showed that the yield strength and tensile strength of C5191 phosphor bronze under high strain rates deformation increased by 32.77% and 11.07% respectively compared with quasi-static condition, the strain hardening index increases from 0.075 to 0.251, and the strength of the material strain rates sensitivity index change from 0.005 to 0.022, which presented a clear sensitive to strain rates. Therefore, it is claimed that the dominant deformation mechanism was changed by the dislocation motion under different strain rates, and the ability of plastic deformation of C5191 phosphor bronze increased due to the number of movable dislocations increased significantly, started multi-line slip, and the soft effect of adiabatic temperature rise at the strain rate ranging from 500 to 1500 s{sup −1}.

  2. High resolution, large deformation 3D traction force microscopy.

    Science.gov (United States)

    Toyjanova, Jennet; Bar-Kochba, Eyal; López-Fagundo, Cristina; Reichner, Jonathan; Hoffman-Kim, Diane; Franck, Christian

    2014-01-01

    Traction Force Microscopy (TFM) is a powerful approach for quantifying cell-material interactions that over the last two decades has contributed significantly to our understanding of cellular mechanosensing and mechanotransduction. In addition, recent advances in three-dimensional (3D) imaging and traction force analysis (3D TFM) have highlighted the significance of the third dimension in influencing various cellular processes. Yet irrespective of dimensionality, almost all TFM approaches have relied on a linear elastic theory framework to calculate cell surface tractions. Here we present a new high resolution 3D TFM algorithm which utilizes a large deformation formulation to quantify cellular displacement fields with unprecedented resolution. The results feature some of the first experimental evidence that cells are indeed capable of exerting large material deformations, which require the formulation of a new theoretical TFM framework to accurately calculate the traction forces. Based on our previous 3D TFM technique, we reformulate our approach to accurately account for large material deformation and quantitatively contrast and compare both linear and large deformation frameworks as a function of the applied cell deformation. Particular attention is paid in estimating the accuracy penalty associated with utilizing a traditional linear elastic approach in the presence of large deformation gradients.

  3. High resolution, large deformation 3D traction force microscopy.

    Directory of Open Access Journals (Sweden)

    Jennet Toyjanova

    Full Text Available Traction Force Microscopy (TFM is a powerful approach for quantifying cell-material interactions that over the last two decades has contributed significantly to our understanding of cellular mechanosensing and mechanotransduction. In addition, recent advances in three-dimensional (3D imaging and traction force analysis (3D TFM have highlighted the significance of the third dimension in influencing various cellular processes. Yet irrespective of dimensionality, almost all TFM approaches have relied on a linear elastic theory framework to calculate cell surface tractions. Here we present a new high resolution 3D TFM algorithm which utilizes a large deformation formulation to quantify cellular displacement fields with unprecedented resolution. The results feature some of the first experimental evidence that cells are indeed capable of exerting large material deformations, which require the formulation of a new theoretical TFM framework to accurately calculate the traction forces. Based on our previous 3D TFM technique, we reformulate our approach to accurately account for large material deformation and quantitatively contrast and compare both linear and large deformation frameworks as a function of the applied cell deformation. Particular attention is paid in estimating the accuracy penalty associated with utilizing a traditional linear elastic approach in the presence of large deformation gradients.

  4. Deformation processing of high-Tc superconducting oxides

    Science.gov (United States)

    Rajan, K.; German, R. M.; Knorr, D. B.; Maccrone, R. K.; Misiolek, W.; Wright, R. N.

    1989-04-01

    Plastic deformation and texture development in polycrystalline YBa2Cu3O7- δ has been studied to expedite the process development of high-critical-temperature (high-Tc) superconducting wires and tapes. It is anticipated that deformation texture will be a major processing consideration in terms of maximizing critical current density, assessing conductor-fabrication options in light of critical current density, and developing such mechanical properties as strength, toughness and thermal fatigue. The intrinsic texture development in YBa2Cu3O7- δ deformation processing should be highly beneficial, insofar as the c axes of the crystals tend to become oriented along the compression axis. This means that conducting tapes and wires formed by rolling, extrusion and drawing can develop textures with the c axis in the transverse or radial direction, thus maximizing the flow of current along the length of the conductor.

  5. High performance deformable image registration algorithms for manycore processors

    CERN Document Server

    Shackleford, James; Sharp, Gregory

    2013-01-01

    High Performance Deformable Image Registration Algorithms for Manycore Processors develops highly data-parallel image registration algorithms suitable for use on modern multi-core architectures, including graphics processing units (GPUs). Focusing on deformable registration, we show how to develop data-parallel versions of the registration algorithm suitable for execution on the GPU. Image registration is the process of aligning two or more images into a common coordinate frame and is a fundamental step to be able to compare or fuse data obtained from different sensor measurements. E

  6. Deformation behavior of dispersion-strengthened copper at high temperature

    Institute of Scientific and Technical Information of China (English)

    WANG Mengjun; ZHANG Yingchun; LUO Yun; LIU Xinyu

    2006-01-01

    The deformation behavior of dispersion-strengthened copper with different compositions was investigated by hot compression simulation tests on a Gleeble-1500 thermal-mechanical simulator. The microstructure during deformation at high temperature was also studied. The result shows that at the beginning of hot compression simulation, the flowing stress of the dispersion-strengthened copper quickly attains a peak value and the stress shows a greater decrease when the temperature is higher and the strain rate is lower. The dispersion particles lead to an obvious increase in the recrystallization temperature. Under experimental conditions, dynamic recovery is the main softening method. The constitutive equation at high temperature of 1.2%Al2O3-0.4%WC/Cu is obtained.

  7. HIGH VISCOUS STRESS OF ORIENTED POLYOLEFINS UNDER UNIAXIAL TENSILE DEFORMATION

    Institute of Scientific and Technical Information of China (English)

    Bing Na; Qin Zhang; Hong Yang; Qiang Fu; Yong-feng Men

    2007-01-01

    In this communication, by means of stress relaxation experiments, the viscous stress at various strains during tensile deformation of oriented polyolefin samples including high density polyethylene (HDPE), linear low density polyethylene (LLDPE) and isotactic polypropylene (iPP), has been determined. The viscous stress in the oriented samples takes up to 50%-70% of the total stress, which is unusually high compared with their isotropic counterparts. The unusual high viscous stress was discussed based on mainly the existence of shish structure in oriented polyolefins, which could enhance the inter-lamella coupling significantly.

  8. Dependence of Deformation Twinning on Grain Orientation and Texture Evolution of High Manganese TWIP Steels at Different Deformation Temperatures%Dependence of Deformation Twinning on Grain Orientation and Texture Evolution of High Manganese TWIP Steels at Different Deformation Temperatures

    Institute of Scientific and Technical Information of China (English)

    FANG Xiu-hui; YANG Ping; LU Fa-yun; MENG Li

    2011-01-01

    Mechanical properties, microstructure and texture evolution were studied in two tensile-deformed high manganese TWIP steels at different temperatures. Special attention was paid to the effects of deformation tempera- ture and grain orientation on twinning behavior. The results showed that, at --70 ℃ and at room temperature, both twins and hexagonal martensite were found in a lower manganese steel of 26Mn. With deformation temperature ris- ing, twins became less and they disappeared at 500 ℃. Strong 〈111〉 texture appeared at 300 ℃, while it weakened at 500 ℃ due to the low strain rate and higher stacking fault energy. EBSD measurement revealed the dependence of deformation twinning on grain orientation at all test temperatures.

  9. Microstructural development of high temperature deformed AZ31 magnesium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Shahbeigi Roodposhti, Peiman, E-mail: pshahbe@ncsu.edu; Sarkar, Apu; Murty, Korukonda Linga

    2015-02-25

    Due to their significant role in automobile industries, high temperature deformation of Mg–Al–Zn alloys (AZ31) at constant stress (i.e. creep) were studied at a wide range of stresses and temperatures to characterize underlying deformation mechanism, dynamic recrystallization (DRX) and dislocation density evolution. Various microstructures (e.g. grain growth & DRX) are noted during steady-state creep mechanisms such as grain boundary sliding (GBS), dislocation glide creep (DGC) and dislocation climb creep (DCC). Although a combination of DRX and grain growth is characteristic of low stacking fault energy materials like Mg alloys at elevated temperatures, observation reveals grain growth at low strain-rates (GBS region) along with dynamic recovery (DRV) mechanism. X-Ray Diffraction (XRD) analysis revealed a decrease in dislocation density during GBS region while it increased under dislocation based creep mechanisms which could be related to the possible DRV and DRX respectively. Scanning Electron Microscopic (SEM) characterization of the fracture surface reveals more inter-granular fracture for large grains (i.e. GBS region with DRV process) and more dimple shape fracture for small grains (i.e. DGC & DCC region with DRX)

  10. Revisiting the deformed high shoreline of Lake Bonneville

    Science.gov (United States)

    Chen, Christine Y.; Maloof, Adam C.

    2017-03-01

    Since G. K. Gilbert's foundational work in the eastern Great Basin during the late 1800s, the late Pleistocene Lake Bonneville (30-10 ka) has been recognized as a natural laboratory for various Quaternary studies, including lithospheric deformation due to surface loading and climate-forced water balance changes. Such studies rely on knowledge of the elevations of Lake Bonneville's paleoshoreline features and depositional landforms, which record a complex history of lake level variations induced by deglacial climate change. In this paper, we present (1) a new compilation of 178 elevation measurements of shoreline features marking Lake Bonneville's greatest areal extent measured using high-precision differential GPS (dGPS), and (2) a reconstructed outline of the highest shoreline based on dGPS measurements, submeter-resolution aerial imagery, topographic digital elevation models (DEMs), and field observations. We also (3) devise a simplified classification scheme and method for standardizing shoreline elevation measurement for different shoreline morphologies that includes constraints on the position of the still water level (SWL) relative to each feature type. The deformation pattern described by these shoreline features can help resolve the relative effects of local hydro-isostasy due to the lake load and regional solid earth deflection due to the Laurentide ice sheet, with potential implications for Earth rheology, glacial isostatic adjustment, and eustatic sea level change.

  11. Deformation reinforcement theory and its application to high arch dams

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    In this paper,the deformation reinforcement theory(DRT) proposed by the authors is elaborated with a new definition of instability that an elasto-plastic structure is not stable if it cannot satisfy simultaneously equilibrium condition,kinematical admissibility and constitutive equations under the prescribed loading.Starting from the definition,a proof is established to the principle of minimum plastic complementary energy for failured structures.It is revealed that the principle of mini-mum plastic complementary energy results in relaxed constitutive equations,especially,yield conditions.It is demonstrated with case studies that many key issues in arch dam design,e.g.,global stability,dam-toe reinforcement,dam-toe cracking,dam-abut-ment reinforcement,can be well solved within the framework of the deformation reinforcement theory.The structural global stability can be described by the curve of the plastic complementary energy vs overloading factor.The unbalanced-forces obtained by elasto-plastic FEM can be used as the basis of analysis of global stability,dam-heel cracking,dam-toe anchorage and reinforcement of faults of high arch dams and their foundations.

  12. Thermal behavior of Nickel deformed to ultra-high strain by high pressure torsion

    DEFF Research Database (Denmark)

    Zhang, Hongwang; Huang, Xiaoxu; Pippan, Richard

    2012-01-01

    Polycrystalline Ni (99.5 %) has been deformed to an ultra-high strain of εvM=100 (εvM, von Mises strain) by high pressure torsion (HPT) at room temperature. The deformed sample is nanostructured with an average boundary spacing of 90 nm, a high density of dislocations of >1015m-2 and a large....... The isochronal annealing leads to a hardness drop in three stages: a relatively small decrease at low temperatures (recovery) followed by a rapid decrease at intermediate temperatures (discontinuous recrystallization) and a slow decrease at high temperatures (grain growth). Due to the presence of a small amount...

  13. Charged particle beam scanning using deformed high gradient insulator

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Yu -Jiuan

    2015-10-06

    Devices and methods are provided to allow rapid deflection of a charged particle beam. The disclosed devices can, for example, be used as part of a hadron therapy system to allow scanning of a target area within a patient's body. The disclosed charged particle beam deflectors include a dielectric wall accelerator (DWA) with a hollow center and a dielectric wall that is substantially parallel to a z-axis that runs through the hollow center. The dielectric wall includes one or more deformed high gradient insulators (HGIs) that are configured to produce an electric field with an component in a direction perpendicular to the z-axis. A control component is also provided to establish the electric field component in the direction perpendicular to the z-axis and to control deflection of a charged particle beam in the direction perpendicular to the z-axis as the charged particle beam travels through the hollow center of the DWA.

  14. Advanced Actuator Concepts for High Precision Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — TRS Technologies proposes to develop a variety of single crystal actuators for adaptive optics deformable mirrors. Single crystal piezoelectric actuators are...

  15. Variable-intercept panel model for deformation zoning of a super-high arch dam.

    Science.gov (United States)

    Shi, Zhongwen; Gu, Chongshi; Qin, Dong

    2016-01-01

    This study determines dam deformation similarity indexes based on an analysis of deformation zoning features and panel data clustering theory, with comprehensive consideration to the actual deformation law of super-high arch dams and the spatial-temporal features of dam deformation. Measurement methods of these indexes are studied. Based on the established deformation similarity criteria, the principle used to determine the number of dam deformation zones is constructed through entropy weight method. This study proposes the deformation zoning method for super-high arch dams and the implementation steps, analyzes the effect of special influencing factors of different dam zones on the deformation, introduces dummy variables that represent the special effect of dam deformation, and establishes a variable-intercept panel model for deformation zoning of super-high arch dams. Based on different patterns of the special effect in the variable-intercept panel model, two panel analysis models were established to monitor fixed and random effects of dam deformation. Hausman test method of model selection and model effectiveness assessment method are discussed. Finally, the effectiveness of established models is verified through a case study.

  16. Microstructure and Property of High Carbonic-Chromium Cast Steel with Different Hot Deformation Ratio

    Institute of Scientific and Technical Information of China (English)

    XU Tao; WANG Jiu-liang; ZHANG Run-jun; CHAO Guo-hua; LIU Jian-hua

    2004-01-01

    The microstructure and properties of high carbonic-chromium cast steel subjected to different hot deformation ratios were studied. The experimental results show that the microstructure and properties of high carbonic-chromium cast steel are obviously improved after hot deformation, and the best mechanical properties of the cast steel can be obtained under hot deformation ratio of 40 %-50 %, which leads to the morphology change of eutectic carbide and the precipitation of granular carbides.

  17. High-Resolution Reciprocal Space Mapping for Characterizing Deformation Structures

    DEFF Research Database (Denmark)

    Pantleon, Wolfgang; Wejdemann, Christian; Jakobsen, Bo

    2014-01-01

    each subgrain, but larger variations between different subgrains. On average, subgrains experience backward strains, whereas dislocation walls are strained in a forward direction. Based on these observations the necessary revision of the classical composite model is outlined. Additionally, subgrain...... relaxation occurs, but no changes in number, size and orientation of the subgrains are observed. The radial profile asymmetry becomes reversed, when pre-deformed specimens are deformed in tension along a perpendicular axis....

  18. Microstructure and properties of 700 MPa grade HSLA steel during high temperature deformation

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Xizhang, E-mail: chenxizhang@wzu.edu.cn [School of Mechanical and Electrical Engineering, Wenzhou University, Wenzhou 325035 (China); School of Material Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Huang, Yuming, E-mail: Hero320@163.com [School of Material Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Lei, Yucheng, E-mail: Yclei@ujs.edu.cn [School of Material Science and Engineering, Jiangsu University, Zhenjiang 212013 (China)

    2015-05-15

    Highlights: • Hot deformation behavior of 700 MPa HSLA steel above 1200 °C in was detailed studied. • Uniform and granular bainite is formed when the deformation amount is 40%. • Deformation resistance value under steady-equilibrium state is about 56 MPa. - Abstract: A high temperature deformation experiment was conducted on a high strength low alloy (HSLA) steel Q690 using Thermecmastor-Z thermal/physical simulator. During the experiment, the specimens were heated from room temperature to 1200 °C with the heating rate of 10 °C/s and 50 °C/s, respectively. The deformation temperature was 1200 °C and the deformation amounts were 0%, 10% and 40%, respectively. The microstructures, stress–strain diagram and hardness were obtained. The results revealed that the microstructure transformation of deformed austenite was quite different from that of the normal situation. With the increasing of deformation amount, more lath-shaped microstructure and less granulous microstructure were observed. The compressive deformation effectively prevented the precipitation of carbides. Larger deformation amount or lower heating rate was conducive to the atomic diffusion, which led to the microstructure uniformity and hardness decreasing. The maximum stress was 68.4 MPa and the steady stress was about 56 MPa.

  19. Deformation and Shear Band Development in an Ultrahigh Carbon Steel During High Strain Rate Deformation

    Energy Technology Data Exchange (ETDEWEB)

    Lesuer, D R; Syn, C K; Sherby, O D

    2004-07-06

    The mechanical response of a pearlitic UHCS-1.3C steel deformed at approximately 4000 s{sup -1} to large strains ({var_epsilon} = -0.9) has been studied. Failure, at both the macroscopic and the microscopic levels has been evaluated, and the ability of the material to absorb energy in compression has been examined. Failure occurred by the development of a shear band. However before failure, extensive buckling of the carbide plates was observed and the UHCS-1.3C material exhibited significant potential for compressive ductility and energy absorption due to the distributed buckling of these plates. Strain localization during adiabatic shear band development resulted in the formation of austenite. Subsequent cooling produced a divorced-eutectoid transformation with associated deformation, which resulted in a microstructure consisting of 50 to 100 nm sized grains. The stress-strain behavior within the shear band has also been determined. The results are used to critically evaluate the maximum shear stress criterion of shear band development. New criteria for the development of shear bands are developed based on a strain energy concept.

  20. Reversibility of Lpo in Olivine during Deformation at High Pressure

    Science.gov (United States)

    Li, L.; Weidner, D. J.

    2014-12-01

    Olivine texture has been reported as an important contributor to the seismic anisotropy in the upper mantle. Experimental studies of deformation of olivine have also shown flow-driven lattice preferred orientation. In this study, we focus on in situ control and monitoring of LPO formation of olivine using synchrotron X-ray radiation coupled with DDIA multi-anvil deformation device. Using an energy-dispersive X-ray coupled a 10-element SSD detector; we apply a sinusoidal stress on the sample, which allows identification of growth of LPO in the specimen with relative robust signal even with small strain fields. Our data show palpable correlations among stress, strain and LPO as well as the variations among sub-grains marked by individual (hkl). This study is to demonstrate the versatile functions of X-ray for characterizing the deformation study of minerals.

  1. New Developments in Deformation Experiments at High Pressure

    Energy Technology Data Exchange (ETDEWEB)

    Durham, W B; Weidner, D J; Karato, S; Wang, Y

    2004-01-09

    Although the importance of rheological properties in controlling the dynamics and evolution of the whole mantle of Earth is well-recognized, experimental studies of rheological properties and deformation-induced microstructures have mostly been limited to low-pressure conditions. This is mainly a result of technical limitations in conducting quantitative rheological experiments under high-pressure conditions. A combination of factors is changing this situation. Increased resolution of composition and configuration of Earth's interior has created a greater demand for well-resolved laboratory measurement of the effects of pressure on the behavior of materials. Higher-strength materials have become readily available for containing high-pressure research devices, and new analytical capabilities--in particular very bright synchrotron X-ray sources--are now readily available to high-pressure researchers. One of the biggest issues in global geodynamics is the style of mantle convection and the nature of chemical differentiation associated with convectional mass transport. Although evidence for deep mantle circulation has recently been found through seismic tomography (e.g., van der Hilst et al. (1997)), complications in convection style have also been noted. They include (1) significant modifications of flow geometry across the mantle transition zone as seen from high resolution tomographic studies (Fukao et al. 1992; Masters et al. 2000; van der Hilst et al. 1991) and (2) complicated patterns of flow in the deep lower mantle ({approx}1500-2500 km), perhaps caused by chemical heterogeneity (Kellogg et al. 1999; van der Hilst and Karason 1999). These studies indicate that while large-scale circulation involving the whole mantle no doubt occurs, significant deviations from simple flow geometry are also present. Two mineral properties have strong influence on convection: (1) density and (2) viscosity (rheology) contrasts. In the past, the effects of density contrast

  2. Deformation and fracture of low alloy steels at high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Marriott, D.L.; Stubbins, J.F.; Leckie, F.A.; Muddle, B.

    1988-12-01

    This project formed part of the initiative in the AR TD program to characterize high temperature, time-dependent damage processes in low alloy steels, for use in the construction of coal-gasification plant. This project was broadly aimed at adding to the knowledge base for this bainitic form of 2.25Cr 1Mo steel, as it related to time-dependent performance at elevated temperature. Its original intention was to obtain information in specific grades of 2.25Cr 1Mo steel, in particular those containing reduced residual elements and microalloyed modifications, which were being considered as candidate materials at the time. This objective was subsequently modified, in the course of the contract period, to a more generic study of bainitic steel, using the 2.25Cr 1Mo material as a representative of the class. The main thrust of the project was directed initially at the detrimental effect of cyclic loading on creep resistance and manifesting itself in an apparently severe creep-fatigue interaction. Three subtasks were eventually identified. These are: a study of the evolution of microstructural changes in bainitic materials during steady load creep and under constant amplitude cyclic deformation, investigation of the effect of cyclic softening on the fatigue and creep strength of complex geometries, focusing on circumferentially notched bars, and investigation of the influence of environment as a possible cause of observed fatigue/elevated temperature interaction through its effects on crack initiation and propagation, using EDM notched specimens tested in air and vacuum. Results are discussed. 24 refs., 40 figs., 5 tabs.

  3. Study on Damage of High Temperature Plastic Deformation for Al-Li Alloy

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The security of use for Al-Li alloy will be greatly influenced by the damage degree of plastic deformation within it at high temperature . Based on continuum damage mechanics theory, the damage evolution of Al-5.44Mg-2.15Li-0.12Zr alloy during plastic deforming at high temperature is simulated by using the damage evolution model of high temperature plastic deformation. The changing rule of its inner damage with deformation temperature, strain rate and strain is gained in this paper. The equation of damage evolution for high temperature plastic deformation is developed, providing an academic basis for the technology of plastic process of Al-Li alloys.

  4. Modeling of dislocation generation and interaction during high-speed deformation of metals

    DEFF Research Database (Denmark)

    Schiøtz, J.; Leffers, T.; Singh, B.N.

    2002-01-01

    at very high strain rates. We have used molecular-dynamics simulations to investigate high-speed deformation of copper crystals. Even though no pre-existing dislocation sources are present in the initial system, dislocations are quickly nucleated and a very high dislocation density is reached during...... the deformation. Due to the high density of dislocations, many inelastic interactions occur between dislocations, resulting in the generation of vacancies. After the deformation, a very high density of vacancies is observed, in agreement with the experimental observations. The processes responsible...

  5. Liquid deformable mirror for high-order wavefront correction

    NARCIS (Netherlands)

    Vuelban, E.M.; Bhattacharya, N.; Braat, J.J.M.

    2006-01-01

    We propose and demonstrate a novel liquid deformable mirror, based on electrocapillary actuation, for highorder wavefront correction. The device consists of a two-dimensional array of vertically oriented microchannels filled with two immiscible liquids, an aqueous electrolyte, and a viscous dielectr

  6. Mechanism of Austenite Evolution During Deformation of Ultra-High Carbon Steel

    Institute of Scientific and Technical Information of China (English)

    ZHANG Shu-lan; SUN Xin-jun; DONG Han

    2008-01-01

    The mechanism of transformation of austenite to cementite and pearlite during the deformation of ultra-high carbon steel was discussed. The results indicate that the pearlite and cementite can be induced by deformation be-tween Acm to Arcm. The transformation during deformation is still considered as a diffusion-controlled process. With the increase of time and reduction, the pearlite fraction increased. At the beginning of the transformation, the pearli- te was lamelliform. When the rate of reduction was increased to 70%, some of the induced lamellar pearlite was bro-ken up under deformation.

  7. Enhanced Fabrication Processes Development for High Actuator Count Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — It is proposed to advance manufacturing science and technology to improve yield and optical surface figure in high actuator count, high-resolution deformable mirrors...

  8. Variation of low temperature internal friction of microplastic deformation of high purity molybdenum single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Pal-Val, P.P. (AN Ukrainskoj SSR, Kharkov. Fiziko-Tekhnicheskij Inst. Nizkikh Temperatur); Kaufmann, H.J. (Akademie der Wissenschaften der DDR, Berlin)

    1984-08-01

    Amplitude and temperature spectra of ultrasound absorption in weakly deformed high purity molybdenum single crystals of different orientations were measured. The results were discussed in terms of parameter changes related to quasiparticle or dislocation oscillations, respectively, dislocation point defect interactions as well as defect generation at microplastic deformation.

  9. Sustained high basal motion of the Greenland ice sheet revealed by borehole deformation

    DEFF Research Database (Denmark)

    Ryser, Claudia; Luethi, Martin P.; Andrews, Lauren C.;

    2014-01-01

    Ice deformation and basal motion characterize the dynamical behavior of the Greenland ice sheet (GrIS). We evaluate the contribution of basal motion from ice deformation measurements in boreholes drilled to the bed at two sites in the western marginal zone of the GrIS. We find a sustained high am...

  10. Internal state variable models for micro-structure in high temperature deformation of titanium alloys

    Institute of Scientific and Technical Information of China (English)

    LUO Jiao; LI MiaoQuan; LI XiaoLi

    2008-01-01

    There exists an interaction between microstructural evolution and deformation behavior in high temperature deformation of titanium alloys. And the microstruc-ture of titanium alloys is very sensitive to the process parameters of plastic de-formation process. In this paper, on the basis of plastic deformation mechanism of metals and alloys, a microstructural model including dislocation density rate equa-tion and grain growth rate equation is established with the dislocation density rate being an internal state variable. Applying the model to the high temperature de-formation process of Ti60 titanium alloy, the average relative errors of grain sizes between the experiments and the predictions are 9.47% for sampled data, and 13.01% for non-sampled data.

  11. Microcrack formation in high-deformed titanium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Gridnev, V.N.; Ivasishin, O.M.; Svechnikov, V.L. (AN Ukrainskoj SSR, Kiev. Inst. Metallofiziki)

    1984-10-01

    ..cap alpha..-phase interlayers on the ..cap alpha../..beta.. boundary with orientation different from a matrix alloys can act as cause of titanium alloys hardening with simultaneous decrease of their ductility. Electron microexamination of the structure of ..cap alpha..-phase located both on interfaces and in ..cap alpha..-grain volume provides evidence that deformation twinning on different planes and slip in a matrix ..cap alpha..-phase are the mechanism of the ..cap alpha..-phase formation. Examples of ..cap alpha..-phase participation with orientation different from the matrix one are presented in the process of microcracks formation.

  12. Electric anisotropy in high density polyethylene + carbon black composites induced by mechanical deformation

    Energy Technology Data Exchange (ETDEWEB)

    Vigueras-Santiago, E; Hernandez-Lopez, S; Camacho-Lopez, M A; Lara-Sanjuan, O, E-mail: eviguerass@uaemex.m [Laboratorio de Investigacion y Desarrollo de Materiales Avanzados (LIDMA), Facultad de Quimica, UAEM. Paseo Colon esq. con Paseo Tollocan, s/n. C.P. 50000, Toluca (Mexico)

    2009-05-01

    High density polyethylene + carbon black composites with electrical anisotropy was studied. Electrical anisotropy was induced by uniaxial mechanical deformation and injection moulding. We show that anisotropy depends on the carbon black concentration and percentage deformation. Resistivity had the highest anisotropy resistivity around the percolation threshold. Perpendicular resistivity showed two magnitude orders higher than parallel resistivity for injected samples, whereas resistivity showed an inverse behaviour for 100% tensile samples. Both directions were set respect to the deformation axe. Anisotropy could be explained in terms of the molecular deformation (alignment) of the polymer chains as a response of the deformation process originating a redistribution of the carbon black particles in both directions. Alignment of the polymer chains was evidenced by polarized Raman spectroscopy.

  13. Bertram Hopkinson's pioneering work and the dislocation mechanics of high rate deformations and mechanically induced detonations.

    Science.gov (United States)

    Armstrong, Ronald W

    2014-05-13

    Bertram Hopkinson was prescient in writing of the importance of better measuring, albeit better understanding, the nature of high rate deformation of materials in general and, in particular, of the importance of heat in initiating detonation of explosives. This report deals with these subjects in terms of post-Hopkinson crystal dislocation mechanics applied to high rate deformations, including impact tests, Hopkinson pressure bar results, Zerilli-Armstrong-type constitutive relations, shock-induced deformations, isentropic compression experiments, mechanical initiation of explosive crystals and shear banding in metals.

  14. Single Crystal Piezoelectric Deformable Mirrors with High Actuator Density and Large Stroke Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Single crystal piezoelectric deformable mirrors with high actuator density, fine pitch, large stroke and no floating wires will be developed for future NASA science...

  15. TEMPERATURE-DEFORMATION CRITERION OF OPTIMIZATION OF FINE DRAWING HIGH CARBON WIRE ROUTE

    Directory of Open Access Journals (Sweden)

    Y. L. Bobarikin

    2012-01-01

    Full Text Available The temperature-deformation criterion of assessment and optimization of routes of the thin high-carbon wire drawing enabling to increase plastic properties of wire at retaining of its durability is offered.

  16. Microstructural Characteristics of High Rate Plastic Deformation in Elektron (trademark) WE43 Magnesium Alloy

    Science.gov (United States)

    2012-04-01

    Microstructural Characteristics of High Rate Plastic Deformation in Elektron ™ WE43 Magnesium Alloy by Joseph Hamilton, Sarah T. Brennan...Ground, MD 21005-5069 ARL-RP-363 April 2012 Microstructural Characteristics of High Rate Plastic Deformation in Elektron ™ WE43 Magnesium...Alloy Joseph Hamilton, Sara T. Brennan, and Yongho Sohn University of Central Florida Bruce Davis and Rick DeLorme Magnesium Elektron North

  17. Dislocation nucleation and vacancy formation during high-speed deformation of fcc metals

    DEFF Research Database (Denmark)

    Schiøtz, J.; Leffers, T.; Singh, B.N.

    2001-01-01

    dislocation densities in the foils after deformation. This was interpreted as evidence for a new dislocation-free deformation mechanism, resulting in a very high vacancy production rate. In this paper we investigate this proposition using large-scale computer simulations of bulk and thin films of copper......Recently, a dislocation-free deformation mechanism was proposed by Kiritani et al. on the basis of a series of experiments where thin foils of fee metals were deformed at very high strain rates. In the experimental study, they observed a large density of stacking fault tetrahedra but very low....... The dislocations are nucleated as single Shockley partials. The large stresses required before dislocations are nucleated result in a very high dislocation density, and therefore in many inelastic interactions between the dislocations. These interactions create vacancies and a very large vacancy concentration...

  18. Highly Deformed Non-uniform Black Strings in Six Dimensions

    CERN Document Server

    Kalisch, Michael

    2015-01-01

    We construct numerically static non-uniform black string solutions in six dimensions by using pseudo-spectral methods. An appropriately designed adaptation of the methods in regard of the specific behaviour of the field quantities in the vicinity of our numerical boundaries provides us with extremely accurate results, that allows us to get solutions with an unprecedented deformation of the black string horizon. Consequently, we are able to investigate in detail a critical regime within a suitable parameter diagram. In particular, we observe a clearly pronounced maximum in the mass curve, which is in accordance with the results of Kleihaus, Kunz and Radu from 2006. Interestingly, by looking at extremely distorted black strings, we find two further turning points of the mass, resulting in a spiral curve in the black string's phase diagram.

  19. Cryogenic ultrahigh strain rate deformation induced hybrid nanotwinned microstructure for high strength and high ductility

    Science.gov (United States)

    Ye, Chang; Suslov, Sergey; Lin, Dong; Liao, Yiliang; Cheng, Gary J.

    2014-06-01

    Nanocrystalline metallic materials prepared by severe plastic deformation often possess high strength but low ductility due to the low dislocation accumulation capacity of the nanograins. Here, we report a unique process, namely, cryogenic laser shock peening (CLSP), to generate gradient nanotwinned microstructure that leads to high strength while preserving the ductility. It was observed that gradient structure was generated in copper. Near the top surface, nanocrystalline with high dense nanotwins have been observed; with the depth increasing, the fraction of the twin boundaries reduces and more heavily dislocated subgrains are observed. It has been demonstrated that CLSP can significantly improve material strength while preserving the ductility. The mechanism of the formation of gradient microstructure and high dense nanotwins near the surface was discussed. The reason behind the improvement in strength and ductility was investigated.

  20. Field investigations of high stress soft surrounding rocks and deformation control

    Directory of Open Access Journals (Sweden)

    Weijian Yu

    2015-08-01

    Full Text Available Field investigations of high stress soft rock deformations show that the high stress soft rock roadway can slide with large deformation. Severe extrusion and floor heave can also be subsequently observed. The supported roadway can be locally damaged or completely fail, where the floor has a large deformation and/or is seriously damaged. The factors inducing large deformation of surrounding rocks in deep roadway are rock strengths, structure face cutting types, stress states, stress release, support patterns, and construction methods. Based on the deformation characteristics of high stress soft rock roadway, a comprehensive support scheme is proposed. The overall support technology of “step-by-step and joint, hierarchical reinforcement” for roadway is presented, and the anchor cable and bolt parameters to check the design methods are also given. Finally, the proposed comprehensive support method “bolt + metal mesh + U-steel arch + shortcrete + grouting and cable” is used in the extension section of east main haulage roadway at −850 m level of Qujiang coal mine. The 173-day monitoring results show that the average convergence of sidewalls reaches 208 mm, and the average relative convergence of roof and floor reaches 448 mm, suggesting that this kind of support technology for controlling large deformation of high stress soft surrounding rock roadway is effective.

  1. Alloy-dependent deformation behavior of highly ductile nanocrystalline AuCu thin films

    Energy Technology Data Exchange (ETDEWEB)

    Lohmiller, Jochen [Karlsruhe Institute of Technology, Institute for Applied Materials, P.O. Box 3640, 76021 Karlsruhe (Germany); Laboratory for Nanometallurgy, Department of Materials, ETH Zurich, Wolfgang-Pauli-Str. 10, 8093 Zurich (Switzerland); Spolenak, Ralph [Laboratory for Nanometallurgy, Department of Materials, ETH Zurich, Wolfgang-Pauli-Str. 10, 8093 Zurich (Switzerland); Gruber, Patric A., E-mail: patric.gruber@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, P.O. Box 3640, 76021 Karlsruhe (Germany)

    2014-02-10

    Nanocrystalline thin films on compliant substrates become increasingly important for the development of flexible electronic devices. In this study, nanocrystalline AuCu thin films on polyimide substrate were tested in tension while using a synchrotron-based in situ testing technique. Analysis of X-ray diffraction profiles allowed identifying the underlying deformation mechanisms. Initially, elastic and microplastic deformation is observed, followed by dislocation-mediated shear band formation, and eventually macroscopic crack formation. Particularly the influence of alloy composition, heat-treatment, and test temperature were investigated. Generally, a highly ductile behavior is observed. However, high Cu concentrations, annealing, and/or large plastic strains lead to localized deformation and hence reduced ductility. On the other hand, enhanced test temperature allows for a delocalized deformation and extended ductility.

  2. Dynamic recrystallization of electroformed copper liners of shaped charges in high-strain-rate plastic deformation

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The microstructures in the electroformed copper liners of shaped charges after high-strain-rate plastic deformation were investigated by transmission electron microscopy (TEM). Meanwhile, the orientation distribution of the grains in the recovered slug was examined by the electron backscattering Kikuchi pattern (EBSP) technique. EBSP analysis illustrated that unlike the as-formed electroformed copper linersof shaped charges the grain orientations in the recovered slug are distributed along randomly all the directions after undergoing heavily strain deformation at high-strain rate. Optical microscopy shows a typical recrystallization structure, and TEM examination reveals dislocation cells existed in the thin foil specimen. These results indicate that dynamic recovery and recrystallization occur during this plastic deformation process, and the associated deformation temperature is considered to be higher than 0.6 times the melting point of copper.

  3. Effect of high temperature deformation on the structure of Ni based superalloy

    Directory of Open Access Journals (Sweden)

    A. Nowotnik

    2008-04-01

    Full Text Available Purpose: A study on the hot deformation behaviour and dynamic structural processes (dynamic precipitation operating during deformation at elevated temperatures of nickel based superalloy was presented.Design/methodology/approach: Compression tests were carried out on precipitations hardenable nickel based superalloy of Inconel 718 at constant true strain rates of 10-4, 4x10-4s-1 within a temperature range of 720-1150°C. True stress-true strain curves and microstructure analysis of hot deformed alloy were described. Microstructure examination has been carried out on the compressed samples of Inconel 718 alloy using an optical microscope - Nikon 300 and in the scanning electron microscope HITACHI S-3400 (SEM in a conventional back-scattered electron mode on polished sections etched with Marble’s solution.Findings: Structural observations of deformed at high temperatures, previously solution treated Inconel alloy revealed non uniform deformation effects. Distribution of molybdenum-rich carbides was found to be affected by localized flow within the investigated strain range at relatively low deformation temperatures 720 - 850°C. Microstructural examination of the alloy also shown that shear banding, cavities growth and intergranular cracks penetrating through the whole grains were responsible for decrease in the flow stress at temperature of 720, 800 and 850°C and a specimen fracture at larger strains. On the basis of received flow stress values activation energy of a high-temperature deformation process was estimated. Mathematical dependences (σpl -T and σpl - and compression data were used to determine material’s constants. These constants allowed to derive a formula that describes the relationship between strain rate ( ε, deformation temperature (T and flow stress σpl.Research limitations/implications: Even though, the light optical microstructure observation of deformed samples revealed some effects of heterogeneous distribution of

  4. A new grid deformation technology with high quality and robustness based on quaternion

    Directory of Open Access Journals (Sweden)

    Huang Jiangtao

    2014-10-01

    Full Text Available Quality and robustness of grid deformation is of the most importance in the field of aircraft design, and grid in high quality is essential for improving the precision of numerical simulation. In order to maintain the orthogonality of deformed grid, the displacement of grid points is divided into rotational and translational parts in this paper, and inverse distance weighted interpolation is used to transfer the changing location from boundary grid to the spatial grid. Moreover, the deformation of rotational part is implemented in combination with the exponential space mapping that improves the certainty and stability of quaternion interpolation. Furthermore, the new grid deformation technique named “layering blend deformation” is built based on the basic quaternion technique, which combines the layering arithmetic with transfinite interpolation (TFI technique. Then the proposed technique is applied in the movement of airfoil, parametric modeling, and the deformation of complex configuration, in which the robustness of grid quality is tested. The results show that the new method has the capacity to deal with the problems with large deformation, and the “layering blend deformation” improves the efficiency and quality of the basic quaternion deformation method significantly.

  5. A new grid deformation technology with high quality and robustness based on quaternion

    Institute of Scientific and Technical Information of China (English)

    Huang Jiangtao; Gao Zhenghong; Wang Chao

    2014-01-01

    Quality and robustness of grid deformation is of the most importance in the field of aircraft design, and grid in high quality is essential for improving the precision of numerical simulation. In order to maintain the orthogonality of deformed grid, the displacement of grid points is divided into rotational and translational parts in this paper, and inverse distance weighted interpolation is used to transfer the changing location from boundary grid to the spatial grid. Moreover, the deformation of rotational part is implemented in combination with the exponential space mapping that improves the certainty and stability of quaternion interpolation. Furthermore, the new grid deformation technique named‘‘layering blend deformation’’ is built based on the basic quaternion technique, which com-bines the layering arithmetic with transfinite interpolation (TFI) technique. Then the proposed tech-nique is applied in the movement of airfoil, parametric modeling, and the deformation of complex configuration, in which the robustness of grid quality is tested. The results show that the new method has the capacity to deal with the problems with large deformation, and the‘‘layering blend deforma-tion’’ improves the efficiency and quality of the basic quaternion deformation method significantly.

  6. Scale-bridging analysis on deformation behavior of high-nitrogen austenitic steels.

    Science.gov (United States)

    Lee, Tae-Ho; Ha, Heon-Young; Hwang, Byoungchul; Kim, Sung-Joon; Shin, Eunjoo; Lee, Jong Wook

    2013-08-01

    Scale-bridging analysis on deformation behavior of high-nitrogen austenitic Fe-18Cr-10Mn-(0.39 and 0.69)N steels was performed by neutron diffraction, electron backscattered diffraction (EBSD), and transmission electron microscopy (TEM). Two important modes of deformation were identified depending on the nitrogen content: deformation twinning in the 0.69 N alloy and strain-induced martensitic transformation in the 0.39 N alloy. The phase fraction and deformation faulting probabilities were evaluated based on analyses of peak shift and asymmetry of neutron diffraction profiles. Semi in situ EBSD measurement was performed to investigate the orientation dependence of deformation microstructure and it showed that the variants of ε martensite as well as twin showed strong orientation dependence with respect to tensile axis. TEM observation showed that deformation twin with a {111} mathematical left angle bracket 112 mathematical right angle bracket crystallographic component was predominant in the 0.69 N alloy whereas two types of strain-induced martensites (ε and α' martensites) were observed in the 0.39 N alloy. It can be concluded that scale-bridging analysis using neutron diffraction, EBSD, and TEM can yield a comprehensive understanding of the deformation mechanism of nitrogen-alloyed austenitic steels.

  7. Deformation Behavior of Mg-8 wt%Li Alloy under High-speed Impact

    Institute of Scientific and Technical Information of China (English)

    SHA Gui-ying; LIU Chun-zhong; YU Tao; SHI Ji-hong

    2006-01-01

    Deformation behavior of the Mg-8 wt%Li alloy at high strain rate was studied by means of the Split Hopkinson Pressure Bar (with strain rate of 103 s-1). It is found that shear localization proves to be the main damage mode for the alloy during dynamic loading. Strain and strain rate are the two necessary parameters affecting the occurrence of deformation and shear bands. Deformation bands begin to form when the strain and strain rate reach 0.20 and 1 900 s-1 respectively and will develop gradually with the strain rate increasing. Besides, deformation bands will transform into shear bands when the strain and strain rate reach above 0.25 and 3 500 s-1 separately.

  8. Recrystailization Behavior of Deformed Austenite in High Strength Microalloyed Pipeline Steel

    Institute of Scientific and Technical Information of China (English)

    YANG Jing-hong; LIU Qing-you; SUN Dong-bai; LI Xiang-yang

    2009-01-01

    Using methods of single-hit hot compression and stress relaxation after deformation on a Gleeble 1500D thermomechanical simulator,the curves of flow stress and stress relaxation,the microstructure and the recrystallization behavior of Nb-V-Ti high strength microalloyed low carbon pipeline steel were studied,and the influence of the thermomechanical treatment parameters on dynamic and static recrystallization of the steel was investigated.It was found that microalloying elements improved the deformation activation energy and produced a retardation of the recrystallization due to the solid solution and precipitation pinning.The deformation conditions such as deformation temperature,strain,and strain rate influenced the recrystallization kinetics and the microstructure respectively.Equations obtained can be used to valuate and predict the dynamic and static recrystallizations.

  9. Evolution of defects in copper deformed by high-pressure torsion

    Energy Technology Data Exchange (ETDEWEB)

    Cizek, J., E-mail: jakub.cizek@mff.cuni.cz [Faculty of Mathematics and Physics, Charles University in Prague, Department of Low Temperature Physics, V Holesovickach 2, Prague 8, CZ-18000 (Czech Republic); Janecek, M.; Srba, O. [Faculty of Mathematics and Physics, Charles University in Prague, Department of Physics of Materials, Ke Karlovu 5, 12116 Prague 2, CZ-12116 (Czech Republic); Kuzel, R. [Faculty of Mathematics and Physics, Charles University in Prague, Department of Condensed Matter Physics, Ke Karlovu 5, 12116 Prague 2, CZ-12116 (Czech Republic); Barnovska, Z.; Prochazka, I. [Faculty of Mathematics and Physics, Charles University in Prague, Department of Low Temperature Physics, V Holesovickach 2, Prague 8, CZ-18000 (Czech Republic); Dobatkin, S. [A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, Moscow (Russian Federation)

    2011-04-15

    Lattice defects in Cu deformed by high-pressure torsion (HPT) were investigated by positron annihilation spectroscopy (PAS) combined with transmission electron microscopy, X-ray diffraction (XRD) and Vicker's microhardness (HV) measurements. The evolution of the microstructure during HPT processing was studied on samples subjected to various numbers of HPT revolutions using pressures of 2 and 4 GPa. Since strain in torsion deformation increases with the radial distance from the center of rotation, one can expect a non-uniform microstructure across the sample diameter. To examine this, HV was measured at various distances from the center of the HPT-deformed sample and the microstructure at the center was compared with that at the periphery. It was found that HPT-deformed Cu contains a high density of dislocations and also small vacancy clusters formed by the agglomeration of deformation-induced vacancies. The center of the sample exhibits coarser grains, a slightly lower density of dislocations and smaller vacancy clusters compared to the periphery. The dislocation density and concentration of vacancy clusters were evaluated from the combination of the PAS and XRD results. The theoretically estimated concentration of deformation-induced vacancies is of an order of magnitude comparable to that determined in experiment.

  10. Subsurface deformation along major thrusts in the outer-arc high off northwest Sumatra

    Science.gov (United States)

    Misawa, A.; Hirata, K.; Seeber, L.; Arai, K.; Ashi, J.; Rahardiawan, R.; Udrekh, U.; Baba, H.; Kinoshita, M.; Fujiwara, T.; Tokuyama, H.; Nakamura, Y.; Permana, H.; Djajadihardja, Y. S.

    2012-12-01

    A huge ocean-wide tsunami, with average heights of more than 20 meters along the west coast of the northern tip of Sumatra followed the 2004 Sumatra-Andaman earthquake (Mw9.2). Several working hypotheses have been proposed, but the generation mechanism for this tsunami remains unresolved. Several hypotheses suggest a possible coseismic slip on splay faults in the outer-arc-high off northwest Sumatra [e.g., Sibuet et al., 2007]. Among these splay faults, the Middle Thrust(MT) (or possibly the Lower Thrust(LT)), can best account for features of the Indian Ocean tsunamis observed at regional and ocean-wide distances [Hirata et al., 2008]. In 2009, we conducted KY09-09 bathymetry survey offshore northern Sumatra and recognized many geological structures, including candidate traces of these splay faults in the outer-arc-high. In 2010, we conducted the KH-10-5 high-resolution MCS survey with a total of 18 seismic lines to image the subsurface structure associated with LT, MT, and the Upper Thrust(UT) in the outer-arc high. Many of subsurface deformations that can be identified on MCS profiles are distributed along these major thrusts. For an example, more than ten of these MCS profiles show clear indication of subsurface deformation along MT. However, a fraction of subsurface deformations are distributed along other large faults existing between these major thrusts. 14 MCS lines cross basins adjoining MT. Several of these MCS profiles show that the uppermost sediment layers of the basins are deformed, either progressively tilted up to a horizontal sea floor, or sub-parallel tilted along with the sea floor. This suggests geologically "recent" deformation associated with slip along MT. However, other MCS lines did not image such a clear "recent" deformation structures near MT. This may imply lack of deformation, or lack of recent sediment along these profiles to record the deformation. Three MCS lines cross UT of Sibuet et al.[2007] or neighboring basins but we could not

  11. High-Resolution Adaptive Optics Scanning Laser Ophthalmoscope with Dual Deformable Mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Chen, D C; Jones, S M; Silva, D A; Olivier, S S

    2006-08-11

    Adaptive optics scanning laser ophthalmoscope (AO SLO) has demonstrated superior optical quality of non-invasive view of the living retina, but with limited capability of aberration compensation. In this paper, we demonstrate that the use of dual deformable mirrors can effectively compensate large aberrations in the human retina. We used a bimorph mirror to correct large-stroke, low-order aberrations and a MEMS mirror to correct low-stroke, high-order aberration. The measured ocular RMS wavefront error of a test subject was 240 nm without AO compensation. We were able to reduce the RMS wavefront error to 90 nm in clinical settings using one deformable mirror for the phase compensation and further reduced the wavefront error to 48 nm using two deformable mirrors. Compared with that of a single-deformable-mirror SLO system, dual AO SLO offers much improved dynamic range and better correction of the wavefront aberrations. The use of large-stroke deformable mirrors provided the system with the capability of axial sectioning different layers of the retina. We have achieved diffraction-limited in-vivo retinal images of targeted retinal layers such as photoreceptor layer, blood vessel layer and nerve fiber layers with the combined phase compensation of the two deformable mirrors in the AO SLO.

  12. High Strain Rate Deformation Modeling of a Polymer Matrix Composite. Part 1; Matrix Constitutive Equations

    Science.gov (United States)

    Goldberg, Robert K.; Stouffer, Donald C.

    1998-01-01

    Recently applications have exposed polymer matrix composite materials to very high strain rate loading conditions, requiring an ability to understand and predict the material behavior under these extreme conditions. In this first paper of a two part report, background information is presented, along with the constitutive equations which will be used to model the rate dependent nonlinear deformation response of the polymer matrix. Strain rate dependent inelastic constitutive models which were originally developed to model the viscoplastic deformation of metals have been adapted to model the nonlinear viscoelastic deformation of polymers. The modified equations were correlated by analyzing the tensile/ compressive response of both 977-2 toughened epoxy matrix and PEEK thermoplastic matrix over a variety of strain rates. For the cases examined, the modified constitutive equations appear to do an adequate job of modeling the polymer deformation response. A second follow-up paper will describe the implementation of the polymer deformation model into a composite micromechanical model, to allow for the modeling of the nonlinear, rate dependent deformation response of polymer matrix composites.

  13. Expressway deformation mapping using high-resolution TerraSAR-X images

    KAUST Repository

    Shi, Xuguo

    2014-01-27

    Monitoring deformation of linear infrastructures such as expressway and railway caused by natural processes or anthropogenic activities is a vital task to ensure the safety of human lives and properties. Interferometric Synthetic Aperture Radar (InSAR) has been widely recognized as an effective technology to carry out large-area surface deformation mapping. However, its application in linear infrastructure deformation monitoring has not been intensively studied till now. In this article, a modified Small BAseline Subset (SBAS) method is proposed to retrieve the deformation patterns of the expressway. In our method, only the point-like targets identified on the expressway were kept in our analysis, and two complementary subsets of interferograms were formed to better separate the signals of height error and deformation from inteferometric phase observations. We successfully applied this method with multitemporal high-resolution TerraSAR-X images to retrieve the spatialoral pattern of surface deformation along the Beian-Heihe expressway that is located in island-permafrost areas and threatened by geohazards. © 2014 Taylor & Francis.

  14. Cryogenic deformation of high temperature superconductive composite structures

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Peter R. (Groton, MA); Michels, William (Brookline, MA); Bingert, John F. (Jemez Springs, NM)

    2001-01-01

    An improvement in a process of preparing a composite high temperature oxide superconductive wire is provided and involves conducting at least one cross-sectional reduction step in the processing preparation of the wire at sub-ambient temperatures.

  15. On the High Temperature Deformation Behaviour of 2507 Super Duplex Stainless Steel

    Science.gov (United States)

    Mishra, M. K.; Balasundar, I.; Rao, A. G.; Kashyap, B. P.; Prabhu, N.

    2017-01-01

    High temperature deformation behaviour of 2507 super duplex stainless steel was investigated by conducting isothermal hot compression tests. The dominant restoration processes in ferrite and austenite phases present in the material were found to be distinct. The possible causes for these differences are discussed. Based on the dynamic materials model, processing map was developed to identify the optimum processing parameters. The microstructural mechanisms operating in the material were identified. A unified strain-compensated constitutive equation was established to describe the high temperature deformation behaviour of the material under the identified processing conditions. Standard statistical parameter such as correlation coefficient has been used to validate the established equation.

  16. On the High Temperature Deformation Behaviour of 2507 Super Duplex Stainless Steel

    Science.gov (United States)

    Mishra, M. K.; Balasundar, I.; Rao, A. G.; Kashyap, B. P.; Prabhu, N.

    2017-02-01

    High temperature deformation behaviour of 2507 super duplex stainless steel was investigated by conducting isothermal hot compression tests. The dominant restoration processes in ferrite and austenite phases present in the material were found to be distinct. The possible causes for these differences are discussed. Based on the dynamic materials model, processing map was developed to identify the optimum processing parameters. The microstructural mechanisms operating in the material were identified. A unified strain-compensated constitutive equation was established to describe the high temperature deformation behaviour of the material under the identified processing conditions. Standard statistical parameter such as correlation coefficient has been used to validate the established equation.

  17. GDR Feeding of the Highly-Deformed Band in 42Ca

    CERN Document Server

    Kmiecik, M; Styczen, J; Bednarczyk, P; Brekiesz, M; Grebosz, J; Lach, M; Meczynski, W; Zieblinski, M; Zuber, K; Bracco, A; Camera, F; Benzoni, G; Million, B; Leoni, S; Wieland, O; Herskind, B; Curien, D; Dubray, N; Dudek, J; Schunck, N; Mazurek, K

    2004-01-01

    The gamma-ray spectra from the decay of the GDR in the compound nucleus reaction 18O+28Si at bombarding energy of 105 MeV have been measured in an experiment using the EUROBALL IV and HECTOR arrays. The obtained experimental GDR strength function is highly fragmented, with a low energy (10 MeV) component, indicating a presence of a large deformation and Coriolis effects. In addition, the preferential feeding of the highly-deformed band in 42Ca by this GDR low energy component is observed.

  18. Mechanical and structural aspects of high temperature deformation in Ni alloy

    Directory of Open Access Journals (Sweden)

    A. Nowotnik

    2008-02-01

    Full Text Available Purpose: Experimental results on hot deformation and dynamic structural processes of nickel based alloy were reviewed. The attention was given to the analysis of dynamic structural processes which operate during hot deformation of the material.Design/methodology/approach: Hot compression tests were performed on solution treated precipitations hardenable nickel based superalloy of Inconel 718 within a temperature range of 720-1150°C at constant true strain rates of 10-4, 4x10-4s-1. The flow stress curves and microstructure of deformed nickel based superalloy were presented.Findings: During hot compression of solution treated material, highly localized flow was observed at relatively low deformation temperatures 720 - 850°C. The particle distribution and their morphology were not found to be affected by localized flow within the investigated strain range. At low strain rate the shear banding and intergranular cracks and cavities growth were found to be responsible for the observed flow stress decrease at 720, 800 and 850°C and might result in a sample fracture at larger strains.Research limitations/implications: In spite of intense strain hardening due to deformation and phase transformation overlapping, light optical microstructure observation of deformed samples did not reveal significant effects of heterogeneous distribution of the phase components. Therefore, in order to complete and confirm obtained results it is recommended to perform further analysis of the alloy by using transmission electron microscopy technique (TEM.Practical implications: An interaction between dynamic precipitation and flow localization may become an important feature of high temperature performance and may also allow producing specific structures of materials.Originality/value: The contribution of flow localization to the strain hardening or flow softening and the flow stress-strain behavior during hot deformation of precipitation hardenable alloys is still a

  19. Effect of microplastic deformation on the electron ultrasonic absorption in high-purity molybdenum monocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Pal' -Val' , P.P.; Kaufmann, Kh.J.

    1983-03-01

    The low temperature (100-6 K) linear absorption of ultrasound (88 kHz) by high purity molybdenum single crystals have been studied. Both unstrained samples and samples sub ected to microplastic deformation (epsilon<=0.45%) were used. Unstrained samples displayed at T<30 K a rapid increase in the absorption with lowering temperature which is interpreted as an indication of electron viscosity due to electron-phonon collisions. After deformation this part of absorption disappeared. This seems to suggest that microplastic deformation brings about in the crystal a sufficiently large number of defects that can compete with phonons in restricting the electron mean free path. A low temperature dynamic annealing has been revealed in strained samples, that is almost complete recovery of the absorption nature under irradiation with high amplitude sound, epsilon/sub 0/ approximately 10/sup -4/, during 10 min, at 6 K. A new relaxation peak of absorption at 10 K has been found in strained samples.

  20. Internal state variable models for micro- structure in high temperature deformation of titanium alloys

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    There exists an interaction between microstructural evolution and deformation behavior in high temperature deformation of titanium alloys. And the microstruc- ture of titanium alloys is very sensitive to the process parameters of plastic de- formation process. In this paper, on the basis of plastic deformation mechanism of metals and alloys, a microstructural model including dislocation density rate equa- tion and grain growth rate equation is established with the dislocation density rate being an internal state variable. Applying the model to the high temperature de- formation process of Ti60 titanium alloy, the average relative errors of grain sizes between the experiments and the predictions are 9.47% for sampled data, and 13.01% for non-sampled data.

  1. High-resolution adaptive optics scanning laser ophthalmoscope with dual deformable mirrors for large aberration correction

    Energy Technology Data Exchange (ETDEWEB)

    Chen, D; Jones, S M; Silva, D A; Olivier, S S

    2007-01-25

    Scanning laser ophthalmoscopes with adaptive optics (AOSLO) have been shown previously to provide a noninvasive, cellular-scale view of the living human retina. However, the clinical utility of these systems has been limited by the available deformable mirror technology. In this paper, we demonstrate that the use of dual deformable mirrors can effectively compensate large aberrations in the human retina, making the AOSLO system a viable, non-invasive, high-resolution imaging tool for clinical diagnostics. We used a bimorph deformable mirror to correct low-order aberrations with relatively large amplitudes. The bimorph mirror is manufactured by Aoptix, Inc. with 37 elements and 18 {micro}m stroke in a 10 mm aperture. We used a MEMS deformable mirror to correct high-order aberrations with lower amplitudes. The MEMS mirror is manufactured by Boston Micromachine, Inc with 144 elements and 1.5 {micro}m stroke in a 3 mm aperture. We have achieved near diffraction-limited retina images using the dual deformable mirrors to correct large aberrations up to {+-} 3D of defocus and {+-} 3D of cylindrical aberrations with test subjects. This increases the range of spectacle corrections by the AO systems by a factor of 10, which is crucial for use in the clinical environment. This ability for large phase compensation can eliminate accurate refractive error fitting for the patients, which greatly improves the system ease of use and efficiency in the clinical environment.

  2. Integrated optical design for highly dynamic laser beam shaping with membrane deformable mirrors

    Science.gov (United States)

    Pütsch, Oliver; Stollenwerk, Jochen; Loosen, Peter

    2017-02-01

    The utilization of membrane deformable mirrors has raised its importance in laser materials processing since they enable the generation of highly spatial and temporal dynamic intensity distributions for a wide field of applications. To take full advantage of these devices for beam shaping, the huge amount of degrees of freedom has to be considered and optimized already within the early stage of the optical design. Since the functionality of commercial available ray-tracing software has been mainly specialized on geometric dependencies and their optimization within constraints, the complex system characteristics of deformable mirrors cannot be sufficiently taken into account yet. The main reasons are the electromechanical interdependencies of electrostatic membrane deformable mirrors, namely saturation and mechanical clamping, that result in non-linear deformation. This motivates the development of an integrative design methodology. The functionality of the ray-tracing program ZEMAX is extended with a model of an electrostatic membrane mirror. This model is based on experimentally determined influence functions. Furthermore, software routines are derived and integrated that allow for the compilation of optimization criteria for the most relevant analytically describable beam shaping problems. In this way, internal optimization routines can be applied for computing the appropriate membrane deflection of the deformable mirror as well as for the parametrization of static optical components. The experimental verification of simulated intensity distributions demonstrates that the beam shaping properties can be predicted with a high degree of reliability and precision.

  3. Friction properties and deformation mechanisms of halite(-mica) gouges from low to high sliding velocities

    Science.gov (United States)

    Buijze, Loes; Niemeijer, André R.; Han, Raehee; Shimamoto, Toshihiko; Spiers, Christopher J.

    2017-01-01

    The evolution of friction as a function of slip rate is important in understanding earthquake nucleation and propagation. Many laboratory experiments investigating friction of fault rocks are either conducted in the low velocity regime (10-8-10-4 ms-1) or in the high velocity regime (0.01-1 m s-1). Here, we report on the evolution of friction and corresponding operating deformation mechanisms in analog gouges deformed from low to high slip rates, bridging the gap between these low and high velocity regimes. We used halite and halite-muscovite gouges to simulate processes, governing friction, active in upper crustal quartzitic fault rocks, at conditions accessible in the laboratory. The gouges were deformed over a 7 orders of magnitude range of slip rate (10-7-1 m s-1) using a low-to-high velocity rotary shear apparatus, using a normal stress of 5 MPa and room-dry humidity. Microstructural analysis was conducted to study the deformation mechanisms. Four frictional regimes as a function of slip rate could be recognized from the mechanical data, showing a transitional regime and stable sliding (10-7-10-6 m s-1), unstable sliding and weakening (10-6-10-3 m s-1), hardening (10-2-10-1 m s-1) and strong weakening (10-1-1 m s-1). Each of the four regimes can be associated with a distinct microstructure, reflecting a transition from mainly brittle deformation accompanied by pressure solution healing to temperature activated deformation mechanisms. Additionally, the frictional response of a sliding gouge to a sudden acceleration of slip rate to seismic velocities was investigated. These showed an initial strengthening, the amount of which depended on the friction level at which the step was made, followed by strong slip weakening.

  4. Freeform high-speed large-amplitude deformable Piezo Mirrors

    CERN Document Server

    Wapler, Matthias C; Wallrabe, Ulrike

    2013-01-01

    We present a new type of tunable mirror with sharply-featured freeform displacement profiles, large displacements of several 100\\mu m and high operating frequencies close to the kHz range at 15mm diameter. The actuation principle is based on a recently explored "topological" displacement mode of piezo sheets. The prototypes presented here include a rotationally symmetric axicon, a hyperbolic sech-icon and a non-symmetric pyram-icon and are scalable to smaller dimensions. The fabrication process is economic and cleanroom-free, and the optical quality is sufficient to demonstrate the diffraction patterns of the optical elements.

  5. High Tc as a consequence of structure deformation

    Energy Technology Data Exchange (ETDEWEB)

    Djajic, R.P. (Faculty of Technical Sciences, Univ. of Novi Sad (Yugoslavia)); Tosic, B.S.; Setrajcic, J.P. (Inst. of Physics, Univ. of Novi Sad (Yugoslavia)); Mirjanic, D.L. (Faculty of Tech., Univ. of Banja Luka (Yugoslavia))

    1991-12-01

    Based on the experimental fact that doped perovskite structures behave as a system of energetically independent thin layers we developed a theoretical model for a single layer behaviour. It was shown that electron and phonon spectra are functions of azimuthal angle which in turn gives the specific relations for Tc which on the other hand differs significantly from the corresponding value in the BCS theory. The crucial fact, which allows the solution of this equation with high Tc, is the electron-electron interaction constant which in a thin doped layer is for an order or two orders of magnitude greater than the same interaction constant in the ideal infinite structure. (orig.).

  6. In-situ high-P, T X-ray microtomographic imaging during large deformation

    DEFF Research Database (Denmark)

    Wang, Y; Lesher, Charles

    2011-01-01

    We have examined the microstructural evolution of a two-phase composite (olivine + Fe-Ni-S) during large shear deformation, using a newly developed high-pressure X-ray tomography microscope. Two samples were examined: a load-bearing framework–type texture, where the alloy phase (Fe-Ni-S) was pres......We have examined the microstructural evolution of a two-phase composite (olivine + Fe-Ni-S) during large shear deformation, using a newly developed high-pressure X-ray tomography microscope. Two samples were examined: a load-bearing framework–type texture, where the alloy phase (Fe...... deformation at temperatures up to 800 K. Shear strains were introduced by twisting the samples at high pressure and high temperature. At each imposed shear strain, samples were cooled to ambient temperature and tomographic images collected. The three-dimensional tomographic images were analyzed for textural...... evolution. We found that in both samples, Fe-Ni-S, which is the weaker phase in the composite, underwent significant deformation. The resulting lens-shaped alloy phase is subparallel to the shear plane and has a laminated, highly anisotropic interconnected weak layer texture. Scanning electron microscopy...

  7. High Strength Silicon Carbide Foams and Their Deformation Behavior

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Silicon carbide (SiC) foams with a continuously connected open-cell structure were prepared and characterized for their mechanical performance. The apparent densities of SiC foams were controlled between about 0.4 and 1.3 g/cm3, with corresponding compressive strengths ranging from about 13 to 60 MPa and flexural strengths from about 8 to 30 MPa. Compressive testing of the SiC foams yielded stress-strain curves with only one linear-elastic region, which is different from those reported on ceramic foams in literature. This can possibly be attributed to the existence of filaments with fine, dense and high strength microstructures. The SiC and the filaments respond homogeneously to applied loading.

  8. 3D High Resolution Mesh Deformation Based on Multi Library Wavelet Neural Network Architecture

    Science.gov (United States)

    Dhibi, Naziha; Elkefi, Akram; Bellil, Wajdi; Amar, Chokri Ben

    2016-12-01

    This paper deals with the features of a novel technique for large Laplacian boundary deformations using estimated rotations. The proposed method is based on a Multi Library Wavelet Neural Network structure founded on several mother wavelet families (MLWNN). The objective is to align features of mesh and minimize distortion with a fixed feature that minimizes the sum of the distances between all corresponding vertices. New mesh deformation method worked in the domain of Region of Interest (ROI). Our approach computes deformed ROI, updates and optimizes it to align features of mesh based on MLWNN and spherical parameterization configuration. This structure has the advantage of constructing the network by several mother wavelets to solve high dimensions problem using the best wavelet mother that models the signal better. The simulation test achieved the robustness and speed considerations when developing deformation methodologies. The Mean-Square Error and the ratio of deformation are low compared to other works from the state of the art. Our approach minimizes distortions with fixed features to have a well reconstructed object.

  9. Wide aperture piezoceramic deformable mirrors for aberration correction in high-power lasers

    Institute of Scientific and Technical Information of China (English)

    Vadim Samarkin; Alexander Alexandrov; Gilles Borsoni; Takahisa Jitsuno; Pavel Romanov; Aleksei Rukosuev; Alexis Kudryashov

    2016-01-01

    The deformable mirror with the size of 410 mmstacks was developed. The results ×468 mm controlled by the bimorph piezoceramic plates and multilayer piezoceramic of the measurements of the response functions of all the actuators and of the surface shape of the deformable mirror are presented in this paper. The study of the mirror with a Fizeau interferometer and a Shack–Hartmann wavefront sensor has shown that it was possible to improve the flatness of the surface down to a residual roughness of 0.033 μm(RMS). The possibility of correction of the aberrations in high-power lasers was numerically demonstrated.

  10. Numerical modelling of the evolution of conglomerate deformation up to high simple-shear strain

    Science.gov (United States)

    Ran, Hao; Bons, Paul D.; Wang, Genhou; Steinbach, Florian; Finch, Melanie; Ran, Shuming; Liang, Xiao; Zhou, Jie

    2017-04-01

    Deformed conglomerates have been widely used to investigate deformation history and structural analysis, using strain analyses techniques, such as the Rf-Φ and Fry methods on deformed pebbles. Although geologists have focused on the study of deformed conglomerates for several decades, some problems of the process and mechanism of deformation, such as the development of structures in pebbles and matrix, are still not understand well. Numerical modelling provides a method to investigate the process of deformation, as a function of different controlling parameters, up to high strains at conditions that cannot be achieved in the laboratory. We use the 2D numerical modelling platform Elle coupled to the full field crystal visco-plasticity code (VPFFT) to simulate the deformation of conglomerates under simple shear conditions, achieving high finite strains of ≥10. Probably for the first time, we included the effect of an anisotropy, i.e. mica-rich matrix. Our simulations show the deformation of pebbles not only depends on the viscosity contrast between pebbles and matrix but emphasises the importance of interaction between neighbouring pebbles. Under the same finite strain shearing the pebbles of conglomerates with high pebble densities show higher Rf and lower Φ than those of conglomerates with a low density pebbles. Strain localisation can be observed at both the margin of strong pebbles and in the bridging area between the pebbles. At low to medium finite strain, local areas show the opposite (antithetic) shear sense because of the different relative rotation and movement of pebbles or clusters of pebbles. Very hard pebbles retain their original shape and may rotate, depending on the anisotropy of the matrix. σ-clasts are formed by pebbles with moderate viscosity contrast between pebble and a softer matrix. By contrast, δ-clasts are not observed in our simulations with both isotropic and anisotropic matrices, which is consistent with their relative scarcity in

  11. Large-Deformation Displacement Transfer Functions for Shape Predictions of Highly Flexible Slender Aerospace Structures

    Science.gov (United States)

    Ko, William L.; Fleischer, Van Tran

    2013-01-01

    Large deformation displacement transfer functions were formulated for deformed shape predictions of highly flexible slender structures like aircraft wings. In the formulation, the embedded beam (depth wise cross section of structure along the surface strain sensing line) was first evenly discretized into multiple small domains, with surface strain sensing stations located at the domain junctures. Thus, the surface strain (bending strains) variation within each domain could be expressed with linear of nonlinear function. Such piecewise approach enabled piecewise integrations of the embedded beam curvature equations [classical (Eulerian), physical (Lagrangian), and shifted curvature equations] to yield closed form slope and deflection equations in recursive forms.

  12. Columnar deformation of human red blood cell by highly localized fiber optic Bessel beam stretcher

    Science.gov (United States)

    Lee, Sungrae; Joo, Boram; Jeon, Pyo Jin; Im, Seongil; Oh, Kyunghwan

    2015-01-01

    A single human red blood cell was optically stretched along two counter-propagating fiber-optic Bessel-like beams in an integrated lab-on-a-chip structure. The beam enabled highly localized stretching of RBC, and it induced a nonlinear mechanical deformation to finally reach an irreversible columnar shape that has not been reported. We characterized and systematically quantified this optically induced mechanical deformation by the geometrical aspect ratio of stretched RBC and the irreversible stretching time. The proposed RBC mechanism can realize a versatile and compact opto-mechanical platform for optical diagnosis of biological substances in the single cell level. PMID:26601005

  13. Columnar deformation of human red blood cell by highly localized fiber optic Bessel beam stretcher.

    Science.gov (United States)

    Lee, Sungrae; Joo, Boram; Jeon, Pyo Jin; Im, Seongil; Oh, Kyunghwan

    2015-11-01

    A single human red blood cell was optically stretched along two counter-propagating fiber-optic Bessel-like beams in an integrated lab-on-a-chip structure. The beam enabled highly localized stretching of RBC, and it induced a nonlinear mechanical deformation to finally reach an irreversible columnar shape that has not been reported. We characterized and systematically quantified this optically induced mechanical deformation by the geometrical aspect ratio of stretched RBC and the irreversible stretching time. The proposed RBC mechanism can realize a versatile and compact opto-mechanical platform for optical diagnosis of biological substances in the single cell level.

  14. High Temperature Deformation Mechanisms in a DLD Nickel Superalloy

    Directory of Open Access Journals (Sweden)

    Sean Davies

    2017-04-01

    Full Text Available The realisation of employing Additive Layer Manufacturing (ALM technologies to produce components in the aerospace industry is significantly increasing. This can be attributed to their ability to offer the near-net shape fabrication of fully dense components with a high potential for geometrical optimisation, all of which contribute to subsequent reductions in material wastage and component weight. However, the influence of this manufacturing route on the properties of aerospace alloys must first be fully understood before being actively applied in-service. Specimens from the nickel superalloy C263 have been manufactured using Powder Bed Direct Laser Deposition (PB-DLD, each with unique post-processing conditions. These variables include two build orientations, vertical and horizontal, and two different heat treatments. The effects of build orientation and post-process heat treatments on the materials’ mechanical properties have been assessed with the Small Punch Tensile (SPT test technique, a practical test method given the limited availability of PB-DLD consolidated material. SPT testing was also conducted on a cast C263 variant to compare with PB-DLD derivatives. At both room and elevated temperature conditions, differences in mechanical performances arose between each material variant. This was found to be instigated by microstructural variations exposed through microscopic and Energy Dispersive X-ray Spectroscopy (EDS analysis. SPT results were also compared with available uniaxial tensile data in terms of SPT peak and yield load against uniaxial ultimate tensile and yield strength.

  15. Role of deformation twins in static recrystallization kinetics of high-purity alpha titanium

    Science.gov (United States)

    Won, Jong Woo; Lee, Taekyung; Hong, Seong-Gu; Lee, Yongmoon; Lee, Jeong Hun; Lee, Chong Soo

    2016-11-01

    The importance of deformation twins in static recrystallization kinetics of high-purity alpha titanium was investigated by carrying out thermal annealing tests of deformed materials in combination with electron-backscatterdiffraction- based microstructural analysis. Prior to thermal annealing, the material was compressed to a true strain of 0.22 along three directions to introduce different twinning characteristics. Our results showed that deformation twins substantially promoted the static recrystallization process by deepening the microstructural inhomogeneity induced by the formation of twin boundaries and twinning-induced crystallographic lattice reorientation. Twin morphology was also observed to be important because it influenced the extent of microstructural inhomogeneity. Intersecting twin morphology, caused by the activation of multiple twin variants, was more effective than parallel twin morphology, caused by the activation of a single twin variant (or a twin variant pair), because it gave rise to more twin boundaries, more twin boundary junctions (intersections, triple junctions, etc.), and greater in-grain crystallographic orientation spread.

  16. Extreme deformations and clusterization at high spin in the A ~ 40 mass region

    Science.gov (United States)

    Ray, Debisree; Afanasjev, Anatoli

    2015-10-01

    Recent revival of the interest to the study of superdeformation and clusterization in light nuclei has motivated us to undertake the study of extreme deformations in the A ~ 32 - 50 N ~ Z nuclei. Unfortunately, at spin zero the predicted structures with extreme deformation are located at high excitation energies which prevents their experimental observation. On the other hand, the rotation brings such structures closer to the yrast line and, in principle, makes their observation possible with future generation of facilities such as GRETA. Thus, the systematic study of the extremely deformed structures and clusterization has been performed in the framework of cranked relativistic mean field theory. The major features of such structures, the spins at which they become yrast and the possiblities of their experimental observation will be discussed in this presentation. This work has been supported by the U.S. Department of Energy under the Grant DE-FG02-07ER41459.

  17. High resolution transmission electron microscope observation of zero-strain deformation twinning mechanisms in Ag.

    Science.gov (United States)

    Liu, L; Wang, J; Gong, S K; Mao, S X

    2011-04-29

    We have observed a new deformation-twinning mechanism using the high resolution transmission electron microscope in polycrystalline Ag films, zero-strain twinning via nucleation, and the migration of a Σ3{112} incoherent twin boundary (ITB). This twinning mechanism produces a near zero macroscopic strain because the net Burgers vectors either equal zero or are equivalent to a Shockley partial dislocation. This observation provides new insight into the understanding of deformation twinning and confirms a previous hypothesis: detwinning could be accomplished via the nucleation and migration of Σ3{112} ITBs. The zero-strain twinning mechanism may be unique to low staking fault energy metals with implications for their deformation behavior.

  18. High Strain Rate Deformation Modeling of a Polymer Matrix Composite. Part 2; Composite Micromechanical Model

    Science.gov (United States)

    Goldberg, Robert K.; Stouffer, Donald C.

    1998-01-01

    Recently applications have exposed polymer matrix composite materials to very high strain rate loading conditions, requiring an ability to understand and predict the material behavior under these extreme conditions. In this second paper of a two part report, a three-dimensional composite micromechanical model is described which allows for the analysis of the rate dependent, nonlinear deformation response of a polymer matrix composite. Strain rate dependent inelastic constitutive equations utilized to model the deformation response of a polymer are implemented within the micromechanics method. The deformation response of two representative laminated carbon fiber reinforced composite materials with varying fiber orientation has been predicted using the described technique. The predicted results compare favorably to both experimental values and the response predicted by the Generalized Method of Cells, a well-established micromechanics analysis method.

  19. Large adaptive deformable membrane mirror with high actuator density: design and first prototypes

    NARCIS (Netherlands)

    Hamelinck, R.; Rosielle, N.; Steinbuch, M.; Doelman, N.J.

    2005-01-01

    A large adaptive deformable mirror with high actuator density is presented. The DM consists of a thin continuous membrane which acts as the correcting element. A grid of low voltage electro-magnetical push-pull actuators, - located in an actuator plate -, impose out-of-plane displacements in the mir

  20. Large adaptive deformable membrane mirror with high actuator density: design and first prototypes

    NARCIS (Netherlands)

    Hamelinck, R.; Rosielle, N.; Steinbuch, M.; Doelman, N.J.

    2005-01-01

    A large adaptive deformable mirror with high actuator density is presented. The DM consists of a thin continuous membrane which acts as the correcting element. A grid of low voltage electro-magnetical push-pull actuators, - located in an actuator plate -, impose out-of-plane displacements in the

  1. Highly deformable and highly fluid vesicles as potential drug delivery systems: theoretical and practical considerations

    Directory of Open Access Journals (Sweden)

    Romero EL

    2013-08-01

    Full Text Available Eder Lilia Romero, Maria Jose Morilla Nanomedicine Research Program, Department of Science and Technology, National University of Quilmes, Bernal, Buenos Aires, Argentina Abstract: Vesicles that are specifically designed to overcome the stratum corneum barrier in intact skin provide an efficient transdermal (systemic or local drug delivery system. They can be classified into two main groups according to the mechanisms underlying their skin interaction. The first group comprises those possessing highly deformable bilayers, achieved by incorporating edge activators to the bilayers or by mixing with certain hydrophilic solutes. The vesicles of this group act as drug carriers that penetrate across hydrophilic pathways of the intact skin. The second group comprises those possessing highly fluid bilayers, owing to the presence of permeation enhancers. The vesicles of this group can act as carriers of drugs that permeate the skin after the barrier of the stratum corneum is altered because of synergistic action with the permeation enhancers contained in the vesicle structure. We have included a detailed overview of the different mechanisms of skin interaction and discussed the most promising preclinical applications of the last five years of Transfersomes® (IDEA AG, Munich, Germany, ethosomes, and invasomes as carriers of antitumoral and anti-inflammatory drugs applied by the topical route. Keywords: Transfersomes, ethosomes, antitumoral, anti-inflammatory, topical delivery

  2. Highly deformable and highly fluid vesicles as potential drug delivery systems: theoretical and practical considerations

    Science.gov (United States)

    Romero, Eder Lilia; Morilla, Maria Jose

    2013-01-01

    Vesicles that are specifically designed to overcome the stratum corneum barrier in intact skin provide an efficient transdermal (systemic or local) drug delivery system. They can be classified into two main groups according to the mechanisms underlying their skin interaction. The first group comprises those possessing highly deformable bilayers, achieved by incorporating edge activators to the bilayers or by mixing with certain hydrophilic solutes. The vesicles of this group act as drug carriers that penetrate across hydrophilic pathways of the intact skin. The second group comprises those possessing highly fluid bilayers, owing to the presence of permeation enhancers. The vesicles of this group can act as carriers of drugs that permeate the skin after the barrier of the stratum corneum is altered because of synergistic action with the permeation enhancers contained in the vesicle structure. We have included a detailed overview of the different mechanisms of skin interaction and discussed the most promising preclinical applications of the last five years of Transfersomes® (IDEA AG, Munich, Germany), ethosomes, and invasomes as carriers of antitumoral and anti-inflammatory drugs applied by the topical route. PMID:23986634

  3. Transmission electron microscopic studies of deformed high-palladium dental alloys.

    Science.gov (United States)

    Guo, W H; Brantley, W A; Clark, W A T; Xiao, J Z; Papazoglou, E

    2003-06-01

    Objective. The purpose of this study was to employ transmission electron microscopy (TEM) to investigate the microstructures of Pd-Cu-Ga and Pd-Ga dental alloys that had been permanently deformed, in order to obtain information about the deformation behavior of individual phases and changes in microstructure brought about by that deformation.Methods. Heavily deformed regions taken from fractured tensile test bars of the two alloys in the as-cast condition were prepared for TEM analysis, using mechanical grinding and polishing, ion milling, and plasma cleaning. The specimens were examined in the TEM using bright-field and dark-field diffraction contrast imaging. Selected-area and convergent-beam electron diffraction patterns were employed to analyze the structures of the phases, and standardless energy-dispersive X-ray spectrometry was used to determine their mean compositions.Results. For both alloys, tweed structures underwent permanent deformation by twinning, whereas dislocation movement occurred in the face-centered cubic (fcc) palladium solid solution matrix. A body-centered cubic (bcc) phase, previously unreported in our TEM studies and containing a high density of dislocations, was identified in the Pd-Cu-Ga alloy, while fine-scale, stress-induced precipitates were found in some regions of the fcc matrix in the Pd-Ga alloy.Significance. The present results have provided novel information about the mechanical deformation behavior of high-palladium alloys. The stress-induced precipitation in the Pd-Ga dental alloy studied may be a critical component of strengthening mechanisms.

  4. Analytical Modeling of the High Strain Rate Deformation of Polymer Matrix Composites

    Science.gov (United States)

    Goldberg, Robert K.; Roberts, Gary D.; Gilat, Amos

    2003-01-01

    The results presented here are part of an ongoing research program to develop strain rate dependent deformation and failure models for the analysis of polymer matrix composites subject to high strain rate impact loads. State variable constitutive equations originally developed for metals have been modified in order to model the nonlinear, strain rate dependent deformation of polymeric matrix materials. To account for the effects of hydrostatic stresses, which are significant in polymers, the classical 5 plasticity theory definitions of effective stress and effective plastic strain are modified by applying variations of the Drucker-Prager yield criterion. To verify the revised formulation, the shear and tensile deformation of a representative toughened epoxy is analyzed across a wide range of strain rates (from quasi-static to high strain rates) and the results are compared to experimentally obtained values. For the analyzed polymers, both the tensile and shear stress-strain curves computed using the analytical model correlate well with values obtained through experimental tests. The polymer constitutive equations are implemented within a strength of materials based micromechanics method to predict the nonlinear, strain rate dependent deformation of polymer matrix composites. In the micromechanics, the unit cell is divided up into a number of independently analyzed slices, and laminate theory is then applied to obtain the effective deformation of the unit cell. The composite mechanics are verified by analyzing the deformation of a representative polymer matrix composite (composed using the representative polymer analyzed for the correlation of the polymer constitutive equations) for several fiber orientation angles across a variety of strain rates. The computed values compare favorably to experimentally obtained results.

  5. In-situ Phase Transformation and Deformation of Iron at High Pressure andTemperature

    Energy Technology Data Exchange (ETDEWEB)

    Miyagi, Lowell; Kunz, Martin; Knight, Jason; Nasiatka, James; Voltolini, Marco; Wenk, Hans-Rudolf

    2008-07-01

    With a membrane based mechanism to allow for pressure change of a sample in aradial diffraction diamond anvil cell (rDAC) and simultaneous infra-red laser heating, itis now possible to investigate texture changes during deformation and phasetransformations over a wide range of temperature-pressure conditions. The device isused to study bcc (alpha), fcc (gamma) and hcp (epislon) iron. In bcc iron, room temperature compression generates a texture characterized by (100) and (111) poles parallel to the compression direction. During the deformation induced phase transformation to hcp iron, a subset of orientations are favored to transform to the hcp structure first and generate a texture of (01-10) at high angles to the compression direction. Upon further deformation, the remaining grains transform, resulting in a texture that obeys the Burgers relationship of (110)bcc // (0001)hcp. This is in contrast to high temperature results that indicate that texture is developed through dominant pyramidal {2-1-12}<2-1-13> and basal (0001)-{2-1-10} slip based on polycrystal plasticity modeling. We also observe that the high temperature fcc phase develops a 110 texture typical for fcc metals deformed in compression.

  6. High-pressure and high temperature deformation studies of polycrystalline diamond

    Science.gov (United States)

    Yu, Xiaohui

    2011-03-01

    With Vicker's hardness 120 GPa, shear modulus 535 GPa, diamond is the hardest material known to mankind. However, because diamond is difficult to deform, little is known with regard to its constitutive properties such as yield strength. In this work, we present results obtained at NSLS using deformation-DIA on polycrystalline diamond at different P-T conditions. As expected, even at total strains up to 20%, we did not observe the yield point of diamond at room temperature and a confining pressure of 4 GPa. However, for deformation at 1000 and 1200& circ; C, we observed an plastic flow of diamond at total strains of 10% and 5%, respectively, indicating that diamond weakens rapidly when temperature is over 1000& circ; C. We further derived the micro stress of diamond from peak width analysis, and found that the micro and macro stresses show similar variations with total strain at both room temperature and 1000& circ; C. However, at 1200& circ; C, the micro stress remains constant in entire deformation, indicating that stress is uniformly distributed within diamond particles at 1200& circ; C. We also carried out SEM studies on the recovered samples to investigate the miscrostructures, and find that the grain size of diamond decreases substantially during the deformation, from the initial microns to sub-microns for the room temperature deformation, however, almost doesn't change for the 1200& circ; C.

  7. Deformation of contact surfaces in a vacuum interrupter after high-current interruptions

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Haoran; Wang, Zhenxing, E-mail: zxwang@xjtu.edu.cn; Zhou, Zhipeng; Jiang, Yanjun; Wang, Jianhua; Geng, Yingsan; Liu, Zhiyuan [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China)

    2016-08-07

    In a high-current interruption, the contact surface in a vacuum interrupter might be severely damaged by constricted vacuum arcs causing a molten area on it. As a result, a protrusion will be initiated by a transient recovery voltage after current zero, enhancing the local electric field and making breakdowns occur easier. The objective of this paper is to simulate the deformation process on the molten area under a high electric field by adopting the finite element method. A time-dependent Electrohydrodynamic model was established, and the liquid-gas interface was tracked by the level-set method. From the results, the liquid metal can be deformed to a Taylor cone if the applied electric field is above a critical value. This value is correlated to the initial geometry of the liquid metal, which increases as the size of the liquid metal decreases. Moreover, the buildup time of a Taylor cone obeys the power law t = k × E{sup −3}, where E is the initial electric field and k is a coefficient related to the material property, indicating a temporal self-similar characteristic. In addition, the influence of temperature has little impact on the deformation but has great impact on electron emission. Finally, the possible reason to initiate a delayed breakdown is associated with the deformation. The breakdown does not occur immediately when the voltage is just applied upon the gap but is postponed to several milliseconds later when the tip is formed on the liquid metal.

  8. Deformation of contact surfaces in a vacuum interrupter after high-current interruptions

    Science.gov (United States)

    Wang, Haoran; Wang, Zhenxing; Zhou, Zhipeng; Jiang, Yanjun; Wang, Jianhua; Geng, Yingsan; Liu, Zhiyuan

    2016-08-01

    In a high-current interruption, the contact surface in a vacuum interrupter might be severely damaged by constricted vacuum arcs causing a molten area on it. As a result, a protrusion will be initiated by a transient recovery voltage after current zero, enhancing the local electric field and making breakdowns occur easier. The objective of this paper is to simulate the deformation process on the molten area under a high electric field by adopting the finite element method. A time-dependent Electrohydrodynamic model was established, and the liquid-gas interface was tracked by the level-set method. From the results, the liquid metal can be deformed to a Taylor cone if the applied electric field is above a critical value. This value is correlated to the initial geometry of the liquid metal, which increases as the size of the liquid metal decreases. Moreover, the buildup time of a Taylor cone obeys the power law t = k × E-3, where E is the initial electric field and k is a coefficient related to the material property, indicating a temporal self-similar characteristic. In addition, the influence of temperature has little impact on the deformation but has great impact on electron emission. Finally, the possible reason to initiate a delayed breakdown is associated with the deformation. The breakdown does not occur immediately when the voltage is just applied upon the gap but is postponed to several milliseconds later when the tip is formed on the liquid metal.

  9. Sustained High Basal Motion of the Greenland Ice Sheet Revealed by Borehole Deformation

    Science.gov (United States)

    Ryser, Claudia; Luthi, Martin P.; Andrews, Lauren C.; Hoffman, Matthew, J.; Catania, Ginny A.; Hawley, Robert L.; Neumann, Thomas A.; Kristensen, Steen S.

    2014-01-01

    Ice deformation and basal motion characterize the dynamical behavior of the Greenland ice sheet (GrIS). We evaluate the contribution of basal motion from ice deformation measurements in boreholes drilled to the bed at two sites in the western marginal zone of the GrIS. We find a sustained high amount of basal motion contribution to surface velocity of 44-73 percent in winter, and up to 90 percent in summer. Measured ice deformation rates show an unexpected variation with depth that can be explained with the help of an ice-flow model as a consequence of stress transfer from slippery to sticky areas. This effect necessitates the use of high-order ice-flow models, not only in regions of fast-flowing ice streams but in all temperate-based areas of the GrIS. The agreement between modeled and measured deformation rates confirms that the recommended values of the temperature-dependent flow rate factor A are a good choice for ice-sheet models.

  10. Interfacial diffusion in high-temperature deformation of composites: A discrete dislocation plasticity investigation

    Science.gov (United States)

    Shishvan, Siamak S.; Pollock, Tresa M.; McMeeking, Robert M.; Deshpande, Vikram S.

    2017-01-01

    We present a discrete dislocation plasticity (DDP) framework to analyse the high temperature deformation of multi-phase materials (composites) comprising a matrix and inclusions. Deformation of the phases is by climb-assisted glide of the dislocations while the particles can also deform due to stress-driven interfacial diffusion. The general framework is used to analyse the uniaxial tensile deformation of a composite comprising elastic particles with dislocation plasticity only present in the matrix phase. When dislocation motion is restricted to only glide within the matrix a strong size effect of the composite strength is predicted with the strength increasing with decreasing unit cell size due to dislocations forming pile-ups against the matrix/particle interface. Interfacial diffusion decreases the composite strength as it enhances the elongation of the elastic particles along the loading direction. When dislocation motion occurs by climb-assisted glide within the matrix the size effect of the strength is reduced as dislocations no longer arrange high energy pile-up structures but rather form lower energy dislocation cell networks. While interfacial diffusion again reduces the composite strength, in contrast to continuum plasticity predictions, the elongation of the particles is almost independent of the interfacial diffusion constant. Rather, in DDP the reduction in composite strength due to interfacial diffusion is a result of changes in the dislocation structures within the matrix and the associated enhanced dislocation climb rates in the matrix.

  11. Friction role in deformation behaviors of high-strength TA18 tubes in numerical control bending

    Science.gov (United States)

    Fang, Jun; Liang, Chuang; Lu, Shiqiang; Wang, Kelu; Zheng, Deliang

    2017-09-01

    In order to reveal the friction role in deformation behaviors of high-strength TA18 tubes in numerical control (NC) bending, a three dimensional (3D) elastic-plastic finite element (FE) model of high-strength TA18 tubes for whole process in NC bending was established based on ABAQUS code, and its reliability was validated by the experimental results in literature. Then, the bending deformation behaviors under different friction coefficients between tube and various dies were studied with respect to multiple defects such as wall thinning, wall thickening and cross section deformation. The results show that the wall thinning ratio and cross section deformation ratio increase with the increase of the friction coefficient between mandrel and tube f m or decrease of the friction coefficient between pressure die and tube f p, while the friction coefficient between bending die and tube f b has no obvious effect on these. The wall thickening ratio decreases with the increase of f b, f m or decrease of f p.

  12. High Temperature Monotonic and Cyclic Deformation in a Directionally Solidified Nickel-Base Superalloy.

    Science.gov (United States)

    1986-05-01

    discuss mechanisms of deformation including slip mode, strain softening/hardening, and grain boundary effects. Antolovich (4) discussed high...cracking at lower frequencies, for a given number of cycles. Antolovich et. al. (83,85) determined the life to be a trade-off between structural coarsenig...The stability of the precipitate is important in high temperature LCF. As reviewed by Antolovich and Jayaraman (48), it depends on misfit and

  13. THE CHANGE IN DEFORMATION CHARACTERISTICS OF CONCRETE MONOLITHIC HIGH-RISE BUILDINGS

    Directory of Open Access Journals (Sweden)

    V. V. Punahin

    2009-03-01

    Full Text Available In the article results of studies of deformation features of concrete on actuate cement for monolithic high-altitude buildings are presented. It is shown that in construction of the high-altitude monolithic buildings in a summer period of a year one should take into account the character of changing the concrete elasticity and plasticity in time, which differs from the same indices for the concrete of normal hardening.

  14. Nonlinear viscoelastic response of highly filled elastomers under multiaxial finite deformation

    Science.gov (United States)

    Peng, Steven T. J.; Landel, Robert F.

    1990-01-01

    A biaxial tester was used to obtain precise biaxial stress responses of highly filled, high strain capability elastomers. Stress-relaxation experiments show that the time-dependent part of the relaxation response can be reasonably approximated by a function which is strain and biaxiality independent. Thus, isochronal data from the stress-relaxation curves can be used to determine the stored energy density function. The complex behavior of the elastomers under biaxial deformation may be caused by dewetting.

  15. Inelastic deformation behavior of thermal barrier coatings exposed at a high-temperature environment

    Directory of Open Access Journals (Sweden)

    Arai M.

    2010-06-01

    Full Text Available Thermal barrier coatings (TBCs are usually deposited onto the surface of the high-temperature component such as gas turbine, in order to protect it from a hightemperature environment. Coating stress generated by such a high-temperature brings serious damages in TBCs in service. For predicting numerically it, it is necessary to develop the constitutive equation suite to plasam-sprayed TBCs. Previous studies have made clear that the freestanding ceramic coat peeled from TBC coated substrate deforms nonlinearly with a mechanical loading, however the results there have been restricted to the test done using as-sprayed sample. In this study, effect of deposition parameter and high-temperature exposure condition on stress-strain curve of the freestanding ceramic coating sample was examined. The associated deformation process was discussed with the microstructure changes observed after performing a bending test for the exposed sample.

  16. Deformation behavior of a high strength multiphase steel at macro- and micro-scales

    Energy Technology Data Exchange (ETDEWEB)

    Diego-Calderón, I. de, E-mail: irenedediego.calderon@imdea.org [IMDEA Materials Institute, Calle Eric Kandel 2, Getafe 28906, Madrid (Spain); Santofimia, M.J. [Department of Materials Science and Engineering, Delft University of Technology, 2628 CD Delft (Netherlands); Molina-Aldareguia, J.M.; Monclús, M.A.; Sabirov, I. [IMDEA Materials Institute, Calle Eric Kandel 2, Getafe 28906, Madrid (Spain)

    2014-08-12

    Advanced high strength steels via quenching and partitioning (Q and P) process are a mainstream trend in modern steel research. This work contributes to a better understanding of their local mechanical properties and local deformation behavior at the micro-scale in relation to their local microstructure. A low alloyed steel was subjected to Q and P heat treatments leading to the formation of complex multiphase microstructures. Nanoindentation tests were performed to measure nanohardness of individual phases and to generate 2D maps showing nanohardness distribution on the surface of the material. To study local in-plane plastic strain distribution during deformation, in situ tensile tests were carried out using the digital image correlation technique. Significant partitioning of plastic strain between phase microconstituents during tensile deformation is shown. The effect of the microstructure on the mechanical behavior of the Q and P processed steel is analyzed. The local plastic deformation behavior of individual phases is discussed with respect to their strength and their spatial orientation.

  17. HIGH RESOLUTION DEFORMATION TIME SERIES ESTIMATION FOR DISTRIBUTED SCATTERERS USING TERRASAR-X DATA

    Directory of Open Access Journals (Sweden)

    K. Goel

    2012-07-01

    Full Text Available In recent years, several SAR satellites such as TerraSAR-X, COSMO-SkyMed and Radarsat-2 have been launched. These satellites provide high resolution data suitable for sophisticated interferometric applications. With shorter repeat cycles, smaller orbital tubes and higher bandwidth of the satellites; deformation time series analysis of distributed scatterers (DSs is now supported by a practical data basis. Techniques for exploiting DSs in non-urban (rural areas include the Small Baseline Subset Algorithm (SBAS. However, it involves spatial phase unwrapping, and phase unwrapping errors are typically encountered in rural areas and are difficult to detect. In addition, the SBAS technique involves a rectangular multilooking of the differential interferograms to reduce phase noise, resulting in a loss of resolution and superposition of different objects on ground. In this paper, we introduce a new approach for deformation monitoring with a focus on DSs, wherein, there is no need to unwrap the differential interferograms and the deformation is mapped at object resolution. It is based on a robust object adaptive parameter estimation using single look differential interferograms, where, the local tilts of deformation velocity and local slopes of residual DEM in range and azimuth directions are estimated. We present here the technical details and a processing example of this newly developed algorithm.

  18. Plastic Deformation of Micromachined Silicon Diaphragms with a Sealed Cavity at High Temperatures

    Directory of Open Access Journals (Sweden)

    Juan Ren

    2016-02-01

    Full Text Available Single crystal silicon (SCS diaphragms are widely used as pressure sensitive elements in micromachined pressure sensors. However, for harsh environments applications, pure silicon diaphragms are hardly used because of the deterioration of SCS in both electrical and mechanical properties. To survive at the elevated temperature, the silicon structures must work in combination with other advanced materials, such as silicon carbide (SiC or silicon on insulator (SOI, for improved performance and reduced cost. Hence, in order to extend the operating temperatures of existing SCS microstructures, this work investigates the mechanical behavior of pressurized SCS diaphragms at high temperatures. A model was developed to predict the plastic deformation of SCS diaphragms and was verified by the experiments. The evolution of the deformation was obtained by studying the surface profiles at different anneal stages. The slow continuous deformation was considered as creep for the diaphragms with a radius of 2.5 mm at 600 °C. The occurrence of plastic deformation was successfully predicted by the model and was observed at the operating temperature of 800 °C and 900 °C, respectively.

  19. Review of Relationship Between Particle Deformation, Coating Microstructure, and Properties in High-Pressure Cold Spray

    Science.gov (United States)

    Rokni, M. R.; Nutt, S. R.; Widener, C. A.; Champagne, V. K.; Hrabe, R. H.

    2017-08-01

    In the cold spray (CS) process, deposits are produced by depositing powder particles at high velocity onto a substrate. Powders deposited by CS do not undergo melting before or upon impacting the substrate. This feature makes CS suitable for deposition of a wide variety of materials, most commonly metallic alloys, but also ceramics and composites. During processing, the particles undergo severe plastic deformation and create a more mechanical and less metallurgical bond with the underlying material. The deformation behavior of an individual particle depends on multiple material and process parameters that are classified into three major groups—powder characteristics, geometric parameters, and processing parameters, each with their own subcategories. Changing any of these parameters leads to evolution of a different microstructure and consequently changes the mechanical properties in the deposit. While cold spray technology has matured during the last decade, the process is inherently complex, and thus, the effects of deposition parameters on particle deformation, deposit microstructure, and mechanical properties remain unclear. The purpose of this paper is to review the parameters that have been investigated up to now with an emphasis on the existent relationships between particle deformation behavior, microstructure, and mechanical properties of various cold spray deposits.

  20. High-temperature tensile deformation behavior of aluminum oxide with and without an applied electric field

    Science.gov (United States)

    Campbell, James

    1998-12-01

    Ceramics are usually considered to be brittle, but under certain conditions some ceramics exhibit a large degree of ductility. They are fine-grained and exhibit superplastic behavior when deformed at high temperatures and low stresses. Whereas superplasticity gives enhanced ductility to metals, it may be the only method for imparting large plasticity to ceramics. Electric fields have been shown to increase ductility, reduce flow stress and reduce cavitation in the superplastic forming of 7475 Al and yttria-stabilized zirconia. Thus, the concurrent application of an electric field may give improved superplastic properties and increased plasticity to a marginally ductile ceramic such as aluminum oxide (alpha-alumina). Fine-grained alumina tensile specimens, formed by dry pressing and sintering a spray-dried powder, were tested in tension at high temperature with and without an electric field of 300 V/cm. Constant strain rate, strain rate cycling and stress relaxation tests were performed. The effects of an electric field on the ductility, flow stress, cavitation and parameters of the Weertman-Dorn deformation equation were measured. Without an electric field, the following deformation parameters were found: the stress exponent n = 2.2, the grain size exponent p = 1.9, the activation energy Q = 490 kJ/mol and the threshold stress sigmao ≈ 0 MPa, indicating structural superplasticity where grain boundary sliding is the predominant deformation mode and was likely accommodated by the motion of grain boundary dislocations. An electric field of 300 V/cm gave a Joule heating temperature increase of ˜30°C and caused the alumina to swell 5--25% (increasing with time), even while under no applied stress, thereby reducing its ductility and flow stress. After correcting for Joule heating and swelling there was still a significant flow stress reduction produced by the field and the following deformation parameters were found: n = 2.2, p = 1.9, Q = 950 kJ/mol and sigmao ≈ 0

  1. Effect of prior deformation on microstructural development and Laves phase precipitation in high-chromium stainless steel.

    Science.gov (United States)

    Hsiao, Z-W; Chen, D; Kuo, J-C; Lin, D-Y

    2017-04-01

    This study investigated the influence of deformation on precipitation behaviour and microstructure change during annealing. Here, the prior deformation of high-chromium stainless steel was tensile deformation of 3%, 6% and 10%, and the specimens were then annealed at 700˚C for 10 h. The specimens were subsequently analyzed using backscattered electron image and electron backscattering diffraction measurements with SEM. Compared with the deformation microstructure, the grains revealed no preferred orientation. The precipitates of TiN and NbC were formed homogenously in the grain interior and at grain boundaries after annealing. Fine Laves phase precipitates were observed in grains and along subgrain boundaries as the deformation increased. Furthermore, the volume fraction of Laves phase increased, but the average particle diameter of precipitate was reduced as the deformation increased. © 2017 The Authors Journal of Microscopy © 2017 Royal Microscopical Society.

  2. Atomic force microscopic study of the structure of high-density polyethylene deformed in liquid medium by crazing mechanism.

    Science.gov (United States)

    Bagrov, D V; Yarysheva, A Y; Rukhlya, E G; Yarysheva, L M; Volynskii, A L; Bakeev, N F

    2014-02-01

    A procedure has been developed for the direct atomic force microscopic (AFM) examination of the native structure of high-density polyethylene (HDPE) deformed in an adsorption-active liquid medium (AALM) by the crazing mechanism. The AFM investigation has been carried out in the presence of a liquid medium under conditions preventing deformed films from shrinkage. Deformation of HDPE in AALM has been shown to proceed through the delocalized crazing mechanism and result in the development of a fibrillar-porous structure. The structural parameters of the crazed polymer have been determined. The obtained AFM images demonstrate a nanosized nonuniformity of the deformation and enable one to observe the structural rearrangements that take place in the deformed polymer after removal of the liquid medium and stress relaxation. A structural similarity has been revealed between HDPE deformed in the AALM and hard elastic polymers.

  3. Use of Terrestrial Laser Scanning Technology for Long Term High Precision Deformation Monitoring

    Science.gov (United States)

    Vezočnik, Rok; Ambrožič, Tomaž; Sterle, Oskar; Bilban, Gregor; Pfeifer, Norbert; Stopar, Bojan

    2009-01-01

    The paper presents a new methodology for high precision monitoring of deformations with a long term perspective using terrestrial laser scanning technology. In order to solve the problem of a stable reference system and to assure the high quality of possible position changes of point clouds, scanning is integrated with two complementary surveying techniques, i.e., high quality static GNSS positioning and precise tacheometry. The case study object where the proposed methodology was tested is a high pressure underground pipeline situated in an area which is geologically unstable. PMID:22303152

  4. Multiscale modeling of high contrast brinkman equations with applications to deformable porous media

    KAUST Repository

    Brown, Donald

    2013-06-18

    Simulating porous media flows has a wide range of applications. Often, these applications involve many scales and multi-physical processes. A useful tool in the analysis of such problems in that of homogenization as an averaged description is derived circumventing the need for complicated simulation of the fine scale features. In this work, we recall recent developments of homogenization techniques in the application of flows in deformable porous media. In addition, homogenization of media with high-contrast. In particular, we recall the main ideas of the homogenization of slowly varying Stokes flow and summarize the results of [4]. We also present the ideas for extending these techniques to high-contrast deformable media [3]. These ideas are connected by the modeling of multiscale fluid-structure interaction problems. © 2013 American Society of Civil Engineers.

  5. High Le Fort I osteotomy for correction of mid-face deformity in Crouzon syndrome.

    Science.gov (United States)

    Nakajima, Yasumichi; Nakano, Hiroyuki; Sumida, Tomoki; Yamada, Tomohiro; Inoue, Kazuya; Sugiyama, Goro; Mishima, Katsuaki; Mori, Yoshihide

    2016-09-01

    An 18-year-old woman with mild Crouzon syndrome was referred with malocclusion and mandibular protrusion. Examination revealed Class III canine and molar relationships, hypoplastic maxilla, 1-mm overbite, and -2-mm overjet. Analysis showed 69° sella-nasion-A, 73.6° sella-nasion-B, and -4.6° A point-nasion-B point angles. Polysomnography revealed respiratory disturbance and 6.3% oxygen desaturation indices of 5.4/h and 9.0/h. We performed double-jaw surgery using high Le Fort I osteotomy and bilateral sagittal split ramus osteotomy for midfacial deformity correction. Twelve months post-surgery, her measures were 70.8°, 72°, -1.2°, 3.0/h, and 6.1/h, respectively. Esthetics were satisfactory. High Le Fort I osteotomy is effective for midfacial deformity correction in patients with Crouzon syndrome. © 2016 Japanese Teratology Society.

  6. Modeling and Predicting Tissue Movement and Deformation for High Intensity Focused Ultrasound Therapy

    Science.gov (United States)

    Liao, Xiangyun; Yuan, Zhiyong; Lai, Qianfeng; Guo, Jiaxiang; Zheng, Qi; Yu, Sijiao; Tong, Qianqian; Si, Weixin; Sun, Mingui

    2015-01-01

    Purpose In ultrasound-guided High Intensity Focused Ultrasound (HIFU) therapy, the target tissue (such as a tumor) often moves and/or deforms in response to an external force. This problem creates difficulties in treating patients and can lead to the destruction of normal tissue. In order to solve this problem, we present a novel method to model and predict the movement and deformation of the target tissue during ultrasound-guided HIFU therapy. Methods Our method computationally predicts the position of the target tissue under external force. This prediction allows appropriate adjustments in the focal region during the application of HIFU so that the treatment head is kept aligned with the diseased tissue through the course of therapy. To accomplish this goal, we utilize the cow tissue as the experimental target tissue to collect spatial sequences of ultrasound images using the HIFU equipment. A Geodesic Localized Chan-Vese (GLCV) model is developed to segment the target tissue images. A 3D target tissue model is built based on the segmented results. A versatile particle framework is constructed based on Smoothed Particle Hydrodynamics (SPH) to model the movement and deformation of the target tissue. Further, an iterative parameter estimation algorithm is utilized to determine the essential parameters of the versatile particle framework. Finally, the versatile particle framework with the determined parameters is used to estimate the movement and deformation of the target tissue. Results To validate our method, we compare the predicted contours with the ground truth contours. We found that the lowest, highest and average Dice Similarity Coefficient (DSC) values between predicted and ground truth contours were, respectively, 0.9615, 0.9770 and 0.9697. Conclusion Our experimental result indicates that the proposed method can effectively predict the dynamic contours of the moving and deforming tissue during ultrasound-guided HIFU therapy. PMID:25993644

  7. Aluminium. II - A review of deformation properties of high purity aluminium and dilute aluminium alloys.

    Science.gov (United States)

    Reed, R. P.

    1972-01-01

    The elastic and plastic deformation behavior of high-purity aluminum and of dilute aluminum alloys is reviewed. Reliable property data, including elastic moduli, elastic coefficients, tensile, creep, fatigue, hardness, and impact are presented. Single crystal tensile results are discussed. Rather comprehensive reference lists, containing publications of the past 20 years, are included for each of the above categories. Defect structures and mechanisms responsible for mechanical behavior are presented. Strengthening techniques (alloys, cold work, irradiation, quenching, composites) and recovery are briefly reviewed.

  8. Suppression of dislocations at high strain rate deformation in a twinning-induced plasticity steel

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Z.Y. [Shenzhen Institute of Research and Innovation, The University of Hong Kong, Shenzhen (China); Department of Mechanical Engineering, The University of Hong Kong, Hong Kong (China); Huang, W., E-mail: whuang@szu.edu.cn [Department of Civil Engineering, Shenzhen University, Shenzhen (China); Huang, M.X., E-mail: mxhuang@hku.hk [Shenzhen Institute of Research and Innovation, The University of Hong Kong, Shenzhen (China); Department of Mechanical Engineering, The University of Hong Kong, Hong Kong (China)

    2015-03-25

    The increase of strain rate generally enhances dislocation evolution in face-centred cubic (FCC) metals. However, by synchrotron X-ray diffraction experiments, the present work demonstrates for the first time that a higher strain rate leads to a lower dislocation density in a twinning-induced plasticity steel with an FCC structure. This unexpected suppression of dislocation evolution has been attributed to the temperature increase due to dissipative heating at high strain rate deformation.

  9. Hardness and phase analysis of IN 718 deformed at high strain rate.

    Science.gov (United States)

    Renhof, L; Guder, S; Werner, E

    2004-06-01

    Specimens of the nickel base alloy IN 718 deformed at high strain rate (approximately 10 s(-1)), as realized in a screw press, have higher strength than parts forged conventionally in a hydraulic press. Microstructure analyses in light and transmission electron microscopes reveal the precipitation of very small Ni(3)Nb particles (gamma"-phase) to be the reason for the increased hardness. Several processing routes are discussed and analyzed in relation to the TTT-diagram of IN 718.

  10. Deformation and annealing behavior of heavily drawn oxygen-free high-conductivity (OFHC) copper

    Science.gov (United States)

    Waryoba, Daudi Rigenda

    Conductor wires used in pulsed high-field magnets require metallic materials with a beneficial combination of high mechanical strength to resist the Lorentz forces and high electrical conductivity to limit temperature excursions due to Joule heating. To achieve the required strength, most conductors are fabricated from microcomposite materials using the work hardening effect after heavy cold deformation such as wire drawing. Since the microstructure and texture of these microcomposites are complex, a detailed systematic study of these materials requires a separate study of the individual phases. This work presents a comprehensive study of the microstructure and microtexture evolution during deformation, and subsequent annealing of heavily deformed OFHC copper wires. Analytical tools used for investigation include optical microscopy, scanning electron microscopy (SEM), orientation-imaging microscopy (OIM) in SEM, and transmission electron microscopy (TEM). Mechanical properties were evaluated by tensile and microhardness testing. Some of the key features of the as-drawn wire are elongated grain size and shear bands. The intensity of the shear bands increased with strain. The ultimate tensile strength (UTS) and the microhardness of the heavily cold-drawn copper wires increased with strain, reached a saturation point and dropped at higher deformation strain. Deformation did not significantly alter the electrical conductivity of the wires. Deformed and recovered microstructures were characterized by a strong+weak duplex fiber texture. Nucleation of recrystallized grains occurred at shear bands and resulted in randomization of texture. On the other hand, recrystallization produced a strong+weak, which later changed to a fiber texture during abnormal grain growth. A detailed analysis showed that recrystallization was a growth-controlled mechanism, and proceeds from the outer surface to the core. Interestingly, secondary recrystallization was observed to proceed from the

  11. Effects of high order deformations on the strength of planar lattice materials

    Institute of Scientific and Technical Information of China (English)

    Bin Wang; Yihui Zhang; Daining Fang

    2008-01-01

    Lattice materials have been attractive over the last decade for use as load-carrying structures, energy absorbing elements and heat exchanging structures because of their excellent mechanical properties and multifunctional charac-ters. However, the quantitative analysis accounting for high order deformations upon the collapse of lattice materials, which is important for their applications, has not been repor-ted. An analytical investigation of yield surfaces with res-pect to the high order deformations was carried out for two typical planar lattice materials: triangular and Kagome lat-tices separately. The analytical results were validated by the finite element method (FEM) simulations. It was found that the effect of high order deformation on the yield strength increases with the relative density. The bending effect of the Kagome lattice is more obvious than that of the triangular one with the same relative density and stress state. The yield strength of the Kagome lattice calculated by neglecting the bending effect overestimates the result by more than 10% when the relative density is higher than about 11.1%, which may not be ignored in engineering applications. The yiel-ding surfaces of the two lattice materials demonstrated in the paper also confirm the analytical results.

  12. Dynamic tensile deformation and fracture of a highly particle-filled composite using SHPB and high-speed DIC method

    OpenAIRE

    Huang F; Guo B.; Chen P; Zhou Z

    2012-01-01

    In this work, various tensile tests, including Brazilian disc test (BDT), flattened Brazilian disc (FBD) test and semi-circular bending (SCB) test, were carried out on a highly particle-filled composite by using a split Hopkinson pressure bar (SHPB). With the consideration of low strength and low wave impedance of the materials, a quartz crystal transducer was embedded in SHPB to measure the loading forces. A high-speed camera was used to capture the deformation and fracture process of materi...

  13. Properties of heterogeneous energetic materials under high strain, high strain rate deformation

    Science.gov (United States)

    Cai, Jing

    Heterogeneous energetic materials have many applications. Their dynamic behavior and microstructural evolution upon plastic deformation have remained not fully understood. The following heterogeneous materials were investigated in the this study: the pure PTFE (usually a mixture of crystalline and amorphous phases), PTFE-Sn, PTFE-Al, PTFE-Al-W, and carbon fibers filled Al alloy. Sample manufacturing processes involving ball milling and Cold Isostatic Pressing were employed. Quasi-static and Hopkinson bar tests were carried out to obtain the compressive strengths of composites. The Conventional Thick-walled Cylinder (TWC) method and newly developed small-scale Hopkinson bar based TWC experiments were conducted to investigate single shear bands and their assembly. Conventional and "soft" drop-weight tests were performed to examine the mechanical properties and the initiation of chemical reactions. Scanning Electron Microscopy was used to detect the details of the microstructures and failure mechanisms of heterogeneous materials. New features in the dynamic behavior of heterogeneous materials were observed. They include the following: (1) Strain softening, instead of thermal softening, is the main mechanism in the initiation of shear bands in explosively driven TWC tests of solid PTFE. (2) Cold isostatically pressed PTFE-Sn samples were more stable with respect to shear localization than solid PTFE. (3) The dynamic collapse of solid PTFE-Al samples with different particle sizes was accomplished with the shear localization bands and cracks. (4) Force chains in the fine W and Al particles were attributed to the high strength of the porous PTFE-Al-W composite containing fine W particles in comparison with composites with coarse W particles. (5) Debonding of metal particles from the PTFE matrix and the fracture of the matrix were identified to be two major mechanisms for the failure of the PTFE-Al-W composites. (6) The formation of PTFE nano-fibers during high strain flow

  14. High-rate Plastic Deformation of Nanocrystalline Tantalum to Large Strains: Molecular Dynamics Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Rudd, R E

    2009-02-05

    Recent advances in the ability to generate extremes of pressure and temperature in dynamic experiments and to probe the response of materials has motivated the need for special materials optimized for those conditions as well as a need for a much deeper understanding of the behavior of materials subjected to high pressure and/or temperature. Of particular importance is the understanding of rate effects at the extremely high rates encountered in those experiments, especially with the next generation of laser drives such as at the National Ignition Facility. Here we use large-scale molecular dynamics (MD) simulations of the high-rate deformation of nanocrystalline tantalum to investigate the processes associated with plastic deformation for strains up to 100%. We use initial atomic configurations that were produced through simulations of solidification in the work of Streitz et al [Phys. Rev. Lett. 96, (2006) 225701]. These 3D polycrystalline systems have typical grain sizes of 10-20 nm. We also study a rapidly quenched liquid (amorphous solid) tantalum. We apply a constant volume (isochoric), constant temperature (isothermal) shear deformation over a range of strain rates, and compute the resulting stress-strain curves to large strains for both uniaxial and biaxial compression. We study the rate dependence and identify plastic deformation mechanisms. The identification of the mechanisms is facilitated through a novel technique that computes the local grain orientation, returning it as a quaternion for each atom. This analysis technique is robust and fast, and has been used to compute the orientations on the fly during our parallel MD simulations on supercomputers. We find both dislocation and twinning processes are important, and they interact in the weak strain hardening in these extremely fine-grained microstructures.

  15. Effect of microplastic deformation on the electron ultrasonic absorption in high-purity molybdenum monocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Pal' -Val' , P.P. (AN Ukrainskoj SSR, Kharkov. Fiziko-Tekhnicheskij Inst. Nizkikh Temperatur); Kaufmann, Kh.J. (Akademie der Wissenschaften der DDR, Berlin)

    1983-03-01

    The low temperature (100-6 K) linear absorption of ultrasound (88 kHz) by high purity molybdenum single crystals have been studied. Both unstrained samples and samples subjected to microplastic deformation (epsilon<=0.45%) were used. Unstrained samples displayed at T<30 K a rapid increase in the absorption with lowering temperature which is interpreted as an indication of electron viscosity due to electron-phonon collisions. After deformation this part of absorption disappeared. This seems to suggest that microplastic deformation brings about in the crystal a sufficiently large number of defects that can compete with phonons in restricting the electron mean free path. A low temperature ''dynamic annealing'' has been revealed in strained samples, that is, almost complete recovery of the absorption nature under irradiation with high amplitude sound, epsilon/sub 0/ approximately 10/sup -4/, during 10 min, at 6 K. A new relaxation peak of absorption at 10 K has been found in strained samples.

  16. Ultrasound Velocity Measurements in High-Chromium Steel Under Plastic Deformation

    Science.gov (United States)

    Lunev, Aleksey; Bochkareva, Anna; Barannikova, Svetlana; Zuev, Lev

    2016-04-01

    In the present study, the variation of the propagation velocity of ultrasound in the plastic deformation of corrosion-resistant high-chromium steel 40X13 with ferrite-carbide (delivery status), martensitic (quenched) and sorbitol (after high-temperature tempering) structures have beem studied/ It is found that each state shows its view of the loading curve. In the delivery state diagram loading is substantially parabolic throughout, while in the martensitic state contains only linear strain hardening step and in the sorbitol state the plastic flow curve is three-step. The velocity of ultrasonic surface waves (Rayleigh waves) was measured simultaneously with the registration of the loading curve in the investigated steel in tension. It is shown that the dependence of the velocity of ultrasound in active loading is determined by the law of plastic flow, that is, the staging of the corresponding diagram of loading. Structural state of the investigated steel is not only changing the type of the deformation curve under uniaxial tension, but also changes the nature of ultrasound speed of deformation.

  17. Development of a Two-Phase Model for the Hot Deformation of Highly-Alloyed Aluminum

    Energy Technology Data Exchange (ETDEWEB)

    A. J. Beaudoin; J. A. Dantzig; I. M. Robertson; B. E. Gore; S. F. Harnish; H. A. Padilla

    2005-10-31

    Conventional processing methods for highly alloyed aluminum consist of ingot casting, followed by hot rolling and thermal treatments. Defects result in lost productivity and wasted energy through the need to remelt and reprocess the material. This research centers on developing a fundamental understanding for deformation of wrought 705X series alloys, a key alloy system used in structural airframe applications. The development of damage at grain boundaries is characterized through a novel test that provides initiation of failure while preserving a controlled deformation response. Data from these mechanical tests are linked to computer simulations of the hot rolling process through a critical measure of damage. Transmission electron microscopy provides fundamental insight into deformation at these high working temperatures, and--in a novel link between microscale and macroscale response--the evolution of microstructure (crystallographic orientation) provides feedback for tuning of friction in the hot rolling process. The key product of this research is a modeling framework for the analysis of industrial hot rolling.

  18. Thermal activation approaches to deformation mechanisms for high Nb containing TiAl base alloys

    Institute of Scientific and Technical Information of China (English)

    刘自成; 王艳丽; 林均品; 张卫军; 陈国良

    2002-01-01

    The deformation mechanisms in a wide temperature range from room temperature to 1200K were investigated by thermal activation approach. Using observed instantaneous stress response to the strain rate jump (Δσtr), the activation volume Va, then the activation enthalpy ΔH, activation free enthalpy ΔG and activation entropy ΔS were calculated. The apparent activation energy of high temperature deformation is estimated to be 3.66eV, which is larger than the self-diffusion coefficient of binary TiAl (3.01eV). The dislocations at 1173K are generally curved or bowed, even helical-shaped dislocations. The climb of ordinary dislocations as well as twinning has greatly contributed to the plastic deformation. The CRSS at 1173K is estimated to be 180MPa. The higher resisting stress at both room temperature and elevated temperature might relate to the high Nb content of the alloy.

  19. Deformation Monitoring of Geomechanical Model Test and Its Application in Overall Stability Analysis of a High Arch Dam

    Directory of Open Access Journals (Sweden)

    Baoquan Yang

    2015-01-01

    Full Text Available Geomechanical model testing is an important method for studying the overall stability of high arch dams. The main task of a geomechanical model test is deformation monitoring. Currently, many types of deformation instruments are used for deformation monitoring of dam models, which provide valuable information on the deformation characteristics of the prototype dams. However, further investigation is required for assessing the overall stability of high arch dams through analyzing deformation monitoring data. First, a relationship for assessing the stability of dams is established based on the comprehensive model test method. Second, a stability evaluation system is presented based on the deformation monitoring data, together with the relationships between the deformation and overloading coefficient. Finally, the comprehensive model test method is applied to study the overall stability of the Jinping-I high arch dam. A three-dimensional destructive test of the geomechanical model dam is conducted under reinforced foundation conditions. The deformation characteristics and failure mechanisms of the dam abutments and foundation were investigated. The test results indicate that the stability safety factors of the dam abutments and foundation range from 5.2 to 6.0. These research results provide an important scientific insight into the design, construction, and operation stages of this project.

  20. Vibration analysis and robust control of highly deformable beams in a heavy pinched loop configuration

    Science.gov (United States)

    Sharma, Nikhil; Kern, Dominik; Seemann, Wolfgang

    2015-02-01

    A heavy pinched loop is formed by bringing and clamping the two ends of a highly deformable slender beam, elastica. A collocation solution technique is implemented for studying the formation statically and dynamically, i.e. small vibrations around the large deformed static solutions, and the earlier work using a shooting method is validated. A new and clear Galerkin formulation capable of modelling damping is established for finding transients, and a new theoretical multi-point boundary value problem approach is used for numerically obtaining the frequency response function. Lastly, the obtained dynamic model is used for active vibration control, wherein a controller is designed using H ∞ algorithm for active damping in a heavy pinched loop for two simplified cases, and the simulated results are shown.

  1. The role of dislocations in varied olivine deformation mechanisms investigated using high-angular resolution electron backscatter diffraction

    Science.gov (United States)

    Wallis, David; Hansen, Lars; Britton, Ben; Wilkinson, Angus

    2016-04-01

    Experimentally-derived flow laws can be used to predict the rheology of rocks deformed under natural conditions only if the same microphysical processes can be demonstrated to control the rate-limiting deformation mechanism in both cases. Olivine rheology may exert a principle control on the strength of the lithosphere, and therefore considerable research effort has been applied to assessing its rheology through experimental, geological, and geophysical approaches. Nonetheless, considerable uncertainty remains regarding the dominant deformation mechanisms in the upper mantle. This uncertainty arises in large part due to our limited understanding of the fundamental deformation processes associated with each mechanism. Future improvements to microphysical models of distinct deformation mechanisms require new insight into the contributions those fundamental processes to the macroscopic behaviour. The dynamics of dislocations is central to modelling viscous deformation of olivine, but characterisation techniques capable of constraining dislocation types, densities, and distributions over the critical grain to polycrystal length-scales have been lacking. High angular resolution electron backscatter diffraction (HR-EBSD), developed and increasingly applied in the material sciences, offers an approach capable of such analyses. HR-EBSD utilises diffraction pattern image cross-correlation to achieve dramatically improved angular resolution (~0.01°) of lattice orientation gradients compared to conventional Hough-based EBSD (~0.5°). This angular resolution allows very low densities (≥ 10^11 m^-2) of geometrically necessary dislocations (GND) to be resolved, facilitating analysis of a wide range of dislocation microstructures. We have developed the application of HR-EBSD to olivine and applied it to samples deformed both experimentally and naturally in grain-size sensitive and grain-size insensitive regimes. The results quantitatively highlight variations in the types and

  2. Analysis of High Temperature Deformed Structure and Dynamic Precipitation in W9Mo3Cr4V Steel

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    With TEM、SEM, various high-temperature deformed structures inW9Mo3Cr4V steel were investigated. The sub-structures,recrystallized nuclei, as well as the dynamic precipitation were also studied and analyzed. The relationship between recrystallized structures and dynamic precipitation was discussed. The results showed that the deformed structures in W9Mo3Cr4V steel are more complicated than those in low alloy steels. Because W9Mo3Cr4V steel is a high-speed steel, there are a large number of residual carbides on the matrix. Also, much dynamic precipitating carbides will precipitate during deformation at high temperature.

  3. Development of wide-range constitutive equations for calculations of high-rate deformation of metals

    Directory of Open Access Journals (Sweden)

    Preston D.

    2011-01-01

    Full Text Available For development of models of strength and compressibility of metals in wide range of pressures (up to several megabar and strain rates ~ 1÷108 s−1, the method of dynamic tests is used. Since direct measurement of strength is impossible under complicated intensive high-rate loading, a formal model is created at first, and then it is updated basing on comparison with many experiments, which are sensitive to shear strength. Elastic-plastic, viscous-elastic-plastic and relaxation integral models became nowadays most commonly used. The basic unsolved problems in simulation of high-rate deformation of metals are mentioned in the paper.

  4. Quantifying and observing viscoplasticity at the nanoscale: highly localized deformation mechanisms in ultrathin nanocrystalline gold films.

    Science.gov (United States)

    Hosseinian, Ehsan; Legros, Marc; Pierron, Olivier N

    2016-04-28

    This study unveils the stress relaxation transient deformation mechanisms in 100 nm-thick, nanocrystalline Au films thanks to a robust quantitative in situ TEM MEMS nanomechanical testing approach to quantify stress relaxation and to perform in situ observations of time-dependent deformation in ultrathin nanocrystalline films. The relaxation is characterized by a decrease in plastic strain rate of more than one order of magnitude over the first ∼30 minutes (from 10(-4) to less than 10(-5) s(-1)). For longer relaxation experiments, the plastic strain rate decreases down to 10(-7) s(-1) after several hours. The power-law exponent n, relating plastic strain rate and stress, continuously decreases from initial large values (n from 6 to 14 at t = 0) down to low values (n ∼ 1-2) after several hours. In situ TEM observations reveal that the relaxation behavior is initially accommodated by highly localized, sustained, intergranular and transgranular dislocation motion. Over time, the dislocation sources become less operative or exhausted, leading to a transition to grain-boundary-diffusion based mechanisms. The results also highlight a promising technique for nanoscale characterization of time-dependent deformation.

  5. INFLUENCE OF ROLL DIAMETERS ON DEFORMATION BEHAVIOUR OF HIGH TEMPERATURE SUPERCONDUCTING TAPE

    Institute of Scientific and Technical Information of China (English)

    LEI Liping; ZHAO Yinghong; ZENG Pan

    2007-01-01

    During plastic process, the material flow is strongly influenced by the contact area between deformed workpiece and die. In rolling process, difference of roll diameter makes the contact area between roll and deformed tape different, which leads to different material flow and the distribution of powder density. A numerical modelling of the first rolling process for 61-filament high temperature superconducting tape is constructed and the influences of roll diameters on deformation behavior of the tape are discussed. It can be found that the BiSrCaCuO (BSCCO) powder in the center of the tape has higher relative density than those in the periphery of the tape during rolling process. With the increase of roll diameter, the length of the contact arc in the roll gap expands which lead to the increasing of transversal strain and the decreasing of the related longitudinal strain. It makes the value of longitudinal strain ratio decrease gradually, which decreases the possibility of occurrence of the transversal shear band, simultaneously it increases the risk of occurrence of longitudinal crack.

  6. Mathematical and computational modeling of a ferrofluid deformable mirror for high-contrast imaging

    Science.gov (United States)

    Lemmer, Aaron J.; Griffiths, Ian M.; Groff, Tyler D.; Rousing, Andreas W.; Kasdin, N. Jeremy

    2016-07-01

    Deformable mirrors (DMs) are an enabling and mission-critical technology in any coronagraphic instrument designed to directly image exoplanets. A new ferro fluid deformable mirror technology for high-contrast imaging is currently under development at Princeton, featuring a flexible optical surface manipulated by the local electromagnetic and global hydraulic actuation of a reservoir of ferro fluid. The ferro fluid DM is designed to prioritize high optical surface quality, high-precision/low-stroke actuation, and excellent low-spatial-frequency performance - capabilities that meet the unique demands of high-contrast coronagraphy in a space-based platform. To this end, the ferro-fluid medium continuously supports the DM face sheet, a configuration that eliminates actuator print-through (or, quilting) by decoupling the nominal surface figure from the geometry of the actuator array. The global pressure control allows independent focus actuation. In this paper we describe an analytical model for the quasi-static deformation response of the DM face sheet to both magnetic and pressure actuation. These modeling efforts serve to identify the key design parameters and quantify their contributions to the DM response, model the relationship between actuation commands and DM surface-profile response, and predict performance metrics such as achievable spatial resolution and stroke precision for specific actuator configurations. Our theoretical approach addresses the complexity of the boundary conditions associated with mechanical mounting of the face sheet, and makes use of asymptotic approximations by leveraging the three distinct length scales in the problem - namely, the low-stroke ( nm) actuation, face sheet thickness ( mm), and mirror diameter (cm). In addition to describing the theoretical treatment, we report the progress of computational multi physics simulations which will be useful in improving the model fidelity and in drawing conclusions to improve the design.

  7. Deformation and degradation of polymers in ultra-high-pressure liquid chromatography.

    Science.gov (United States)

    Uliyanchenko, Elena; van der Wal, Sjoerd; Schoenmakers, Peter J

    2011-09-28

    Ultra-high-pressure liquid chromatography (UHPLC) using columns packed with sub-2 μm particles has great potential for separations of many types of complex samples, including polymers. However, the application of UHPLC for the analysis of polymers meets some fundamental obstacles. Small particles and narrow bore tubing in combination with high pressures generate significant shear and extensional forces in UHPLC systems, which may affect polymer chains. At high stress conditions flexible macromolecules may become extended and eventually the chemical bonds in the molecules can break. Deformation and degradation of macromolecules will affect the peak retention and the peak shape in the chromatogram, which may cause errors in the obtained results (e.g. the calculated molecular-weight distributions). In the present work we explored the limitations of UHPLC for the analysis of polymers. Degradation and deformation of macromolecules were studied by collecting and re-injecting polymer peaks and by off-line two-dimensional liquid chromatography. Polystyrene standards with molecular weight of 4 MDa and larger were found to degrade at UHPLC conditions. However, for most polymers degradation could be avoided by using low linear velocities. No degradation of 3-MDa PS (and smaller) was observed at linear velocities up to 7 mm/s. The column frits were implicated as the main sources of polymer degradation. The extent of degradation was found to depend on the type of the column and on the column history. At high flow rates degradation was observed without a column being installed. We demonstrated that polymer deformation preceded degradation. Stretched polymers eluted from the column in slalom chromatography mode (elution order opposite to that in SEC or HDC). Under certain conditions we observed co-elution of large and small PS molecules though a convolution of slalom chromatography and hydrodynamic chromatography.

  8. Active faults in the deformation zone off Noto Peninsula, Japan, revealed by high- resolution seismic profiles

    Science.gov (United States)

    Inoue, T.; Okamura, Y.; Murakami, F.; Kimura, H.; Ikehara, K.

    2008-12-01

    Recently, a lot of earthquakes occur in Japan. The deformation zone which many faults and folds have concentrated exists on the Japan Sea side of Japan. The 2007 Noto Hanto Earthquake (MJMA 6.9) and 2007 Chuetsu-oki Earthquake (MJMA 6.8) were caused by activity of parts of faults in this deformation zone. The Noto Hanto Earthquake occurred on 25 March, 2007 under the northwestern coast of Noto Peninsula, Ishikawa Prefecture, Japan. This earthquake is located in Quaternary deformation zone that is continued from northern margin of Noto Peninsula to southeast direction (Okamura, 2007a). National Institute of Advanced Industrial Science and Technology (AIST) carried out high-resolution seismic survey using Boomer and 12 channels short streamer cable in the northern part off Noto Peninsula, in order to clarify distribution and activities of active faults in the deformation zone. A twelve channels short streamer cable with 2.5 meter channel spacing developed by AIST and private corporation is designed to get high resolution seismic profiles in shallow sea area. The multi-channel system is possible to equip on a small fishing boat, because the data acquisition system is based on PC and the length of the cable is short and easy to handle. Moreover, because the channel spacing is short, this cable is very effective for a high- resolution seismic profiling survey in the shallow sea, and seismic data obtained by multi-channel cable can be improved by velocity analysis and CDP stack. In the northern part off Noto Peninsula, seismic profiles depicting geologic structure up to 100 meters deep under sea floor were obtained. The most remarkable reflection surface recognized in the seismic profiles is erosion surface at the Last Glacial Maximum (LGM). In the western part, sediments about 30 meters (40 msec) thick cover the erosional surface that is distributed under the shelf shallower than 100m in depth and the sediments thin toward offshore and east. Flexures like deformation in

  9. Formation of Nanostructures in Severely Deformed High-Strength Steel Induced by High-Frequency Ultrasonic Impact Treatment

    Science.gov (United States)

    Dutta, R. K.; Malet, L.; Gao, H.; Hermans, M. J. M.; Godet, S.; Richardson, I. M.

    2015-02-01

    Surface modification by the generation of a nanostructured surface layer induced via ultrasonic impact treatment was performed at the weld toe of a welded high-strength quenched and tempered structural steel, S690QL1 (Fe-0.16C-0.2Si-0.87Mn-0.33Cr-0.21Mo (wt pct)). Such high-frequency peening techniques are known to improve the fatigue life of welded components. The nanocrystallized structure as a function of depth from the top-treated surface was characterized via a recently developed automated crystal orientation mapping in transmission electron microscopy. Based on the experimental observations, a grain refinement mechanism induced by plastic deformation during the ultrasonic impact treatment is proposed. It involves the formation of low-angle misoriented lamellae displaying a high density of dislocations followed by the subdivision of microbands into blocks and the resulting formation of polygonal submicronic grains. These submicronic grains further breakdown into nano grains. The results show the presence of retained austenite even after severe surface plastic deformation. The average grain size of the retained austenite and martensite is 17 and 35 nm, respectively. The in-grain deformation mechanisms are different in larger and smaller grains. Larger grains show long-range lattice rotations, while smaller grains show plastic deformation through grain rotation. Also the smaller nano grains exhibit the presence of short-range disorder. Surface nanocrystallization also leads to an increased fraction of low angle and low energy coincident site lattice boundaries especially in the smaller grains ( nm).

  10. Towards high velocity deformation characterisation of metals and composites using Digital Image Correlation

    Directory of Open Access Journals (Sweden)

    Dulieu-Barton J.M.

    2010-06-01

    Full Text Available Characterisation of materials subject to high velocity deformation is necessary as many materials behave differently under such conditions. It is particularly important for accurate numerical simulation of high strain rate events. High velocity servo-hydraulic test machines have enabled material testing in the strain rate regime from 1 – 500 ε/s. The range is much lower than that experienced under ballistic, shock or impact loads, nevertheless it is a useful starting point for the application of optical techniques. The present study examines the possibility of using high speed cameras to capture images and then extracting deformation data using Digital Image Correlation (DIC from tensile testing in the intermediate strain rate regime available with the test machines. Three different materials, aluminium alloy 1050, S235 steel and glass fibre reinforced plastic (GFRP were tested at different nominal strain rates ranging from quasi static to 200 ε/s. In all cases DIC was able to analyse data collected up to fracture and in some cases post fracture. The use of highspeed DIC made it possible to capture phenomena such as multiple necking in the aluminium specimens and post compression failure in GFRP specimens.

  11. Modeling of high homologous temperature deformation behavior for stress and life-time analyses

    Energy Technology Data Exchange (ETDEWEB)

    Krempl, E. [Rensselaer Polytechnic Institute, Troy, NY (United States)

    1997-12-31

    Stress and lifetime analyses need realistic and accurate constitutive models for the inelastic deformation behavior of engineering alloys at low and high temperatures. Conventional creep and plasticity models have fundamental difficulties in reproducing high homologous temperature behavior. To improve the modeling capabilities {open_quotes}unified{close_quotes} state variable theories were conceived. They consider all inelastic deformation rate-dependent and do not have separate repositories for creep and plasticity. The viscoplasticity theory based on overstress (VBO), one of the unified theories, is introduced and its properties are delineated. At high homologous temperature where secondary and tertiary creep are observed modeling is primarily accomplished by a static recovery term and a softening isotropic stress. At low temperatures creep is merely a manifestation of rate dependence. The primary creep modeled at low homologous temperature is due to the rate dependence of the flow law. The model is unaltered in the transition from low to high temperature except that the softening of the isotropic stress and the influence of the static recovery term increase with an increase of the temperature.

  12. Engineering of surface microstructure transformations using high rate severe plastic deformation in machining

    Science.gov (United States)

    Abolghasem, Sepideh

    research effort, where Large Strain Machining (LSM) is presented as a controlled test of microstructure response. Sample conditions are created using LSM in Face Centered Cubic (FCC) metals, while characterizing the deformation using Digital Image Correlation(DIC) and Infrared(IR) thermography. Microstructural consequences such as grain size, subgrain size and grain boundary responses resulting from the characterized thermomechanical conditions are examined using Electron Back-Scattered Diffraction (EBSD). Once empirical data is generated across the broad thermomechanical conditions, reliable microstructure maps are populated. This characterization can help understand surface microstructures resulting from shear-based manufacturing processes such as turning, milling, shaping, etc. that are created under analogous thermomechanical conditions. Keywords: microstructure characterization, ultrafine grain microstructure, severe plastic deformation, high speed deformation.

  13. Dynamic Grain Growth in Forsterite Aggregates Experimentally Deformed to High Strain

    Science.gov (United States)

    Kellermann Slotemaker, A.; de Bresser, H.; Spiers, C.; Drury, M.

    2004-12-01

    The dynamics of the outer Earth are largely controlled by olivine rheology. From previous work it has become clear that if olivine rocks are deformed to high strain, substantial weakening may occur before steady state mechanical behaviour is approached. This weakening appears directly related to progressive modification of the grain size distribution through competing effects of dynamic recrystallization and syn-deformational grain growth. However, most of our understanding of these processes in olivine comes from tests on coarse-grained materials that were reduced in grain size during straining by grain size insensitive (dislocation) creep mechanisms. The aim of the present study was to investigate microstructure evolution of fine-grained olivine rocks that coarsen in grain size while deforming by grain size sensitive (GSS) creep. We used fine-grained (~1 μ m) olivine aggregates (i.e., forsterite/Mg2SiO4), containing ~0.5 wt% water and 10 vol% enstatite (MgSiO3). Two types of experiments were carried out: 1) Hot isostatic pressing (HIP) followed by axial compression to varying strains up to a maximum of ~45%, at 600 MPa confining pressure and a temperature of 950°C, 2) HIP treatment without axial deformation. Microstructures were characterized by analyzing full grain size distributions and texture using SEM/EBSD. Our stress-strain curves showed continuous hardening. When samples were temporally unloaded for short time intervals, no difference in flow stress was observed before and after the interruption in straining. Strain rate sensitivity analysis showed a low value of ~1.5 for the stress exponent n. Measured grain sizes show an increase with strain up to a value twice that of the starting value. HIP-only samples showed only minor increase in grain size. A random LPO combined with the low n ~1.5 suggests dominant GSS creep controlled by grain boundary sliding. These results indicate that dynamic grain growth occurs in forsterite aggregates deforming by GSS

  14. Deformation properties of highly plastic fissured Palaeogene clay - Lack of stress memory?

    DEFF Research Database (Denmark)

    Krogsbøll, Anette; Hededal, Ole; Foged, Niels Nielsen

    2012-01-01

    are evaluated based on the degree of debonding caused by natural processes insitu as compared to processes induced during severe loading and unloading in laboratory. A long term oedometer test on Lillebælt Clay with a series of loading and unloading cycles was carried out. The test results are used to evaluate...... of fissuring or debonding. Based on a large amount of high quality tests on Palaeogene clay partly encountered at Fehmarn Belt the typical deformational behaviour during unloading and swelling is discussed and evaluated with focus on stress states. K0-OCR relations are established and the relations...

  15. Experimental deformation of coarse-grained rock salt to high strain

    Science.gov (United States)

    Linckens, J.; Zulauf, G.; Hammer, J.

    2016-08-01

    The processes and deformation mechanisms (e.g., dislocation creep, pressure solution, grain boundary sliding, and recrystallization) of rock salt are still a matter of debate. In order to fill this gap, high strain constriction experiments at 345°C, atmospheric pressure and a strain rate of 10-7 s-1 have been conducted on natural halite cuboids (60 × 60 × 45 mm) from the Morsleben mine of Northern Germany. Most samples were almost single crystals and contain a small amount of smaller grains (10-26%). The grain boundaries are decorated with fluid inclusions. The experiments were stopped at different final strains (ɛy = z of 10, 20, 30, and 40%) corresponding to a maximum strain (ɛx) range of 20-170%. The halite is deformed by dislocation creep, and the size of developed subgrains corresponds to the applied stress. The combined Schmid factor and subgrain boundary analysis indicate that slip was largely accommodated by the {110} slip systems, with possible minor contribution by slip on the {100} slip systems. Some of the deformed samples show evidence of grain boundary migration. In addition, subgrains with small misorientations form that result in large cumulative misorientations within a single grain (>40°). However, no subgrain rotation recrystallization is observed (i.e., misorientation angles are <10°). All the experiments show strain hardening, suggesting that recrystallization by grain boundary migration was not extensive and did not reset the microstructure. The experiments show that high finite strain in coarse-grained relatively dry rock salt can be accommodated by dislocation creep, without extensive dynamic recrystallization.

  16. High-temperature deformation and recrystallization: A variational analysis and its application to olivine aggregates

    Science.gov (United States)

    Hackl, Klaus; Renner, JöRg

    2013-03-01

    We develop a framework for a variational analysis of microstructural evolution during inelastic high-temperature deformation accommodated by dislocation mechanisms and diffusive mass transport. A polycrystalline aggregate is represented by a distribution function characterizing the state of individual grains by three variables, dislocation density, grain size, and elastic strain. The aggregate's free energy comprises elastic energy and energies of lattice distortions due to dislocations and grain boundaries. The work performed by the external loading is consumed by changes in the number of defects and their migration leading to inelastic deformation. The variational approach minimizes the rate of change of free energy with the evolution of the state variables under constraints on the aggregate volume, on a relation between changes in plastic strain and dislocation density, and on the form of the dissipation functionals for defect processes. The constrained minimization results in four basic evolution equations, one each for the evolution in grain size and dislocation density and flow laws for dislocation and diffusion creep. Analytical steady state scaling relations between stress and dislocation density and grain size (piezometers) are derived for quasi-homogeneous materials characterized by a unique relation between grain size and dislocation density. Our model matches all currently available experimental observations regarding high-temperature deformation of olivine aggregates with plausible values for the involved micromechanical model parameters. The relation between strain rate and stress for olivine aggregates maintaining a steady state microstructure is distinctly nonlinear in stark contrast to the majority of geodynamical modeling relying on linear relations, i.e., Newtonian behavior.

  17. A review of the effect of prior inelastic deformation on high temperature mechanical response of engineering alloys

    Energy Technology Data Exchange (ETDEWEB)

    Li, D.F. [Department of Mechanical and Aeronautical Engineering, Materials and Surface Science Institute, University of Limerick, Plassey Park, Limerick (Ireland); O' Dowd, N.P., E-mail: noel.odowd@ul.i [Department of Mechanical and Aeronautical Engineering, Materials and Surface Science Institute, University of Limerick, Plassey Park, Limerick (Ireland); Davies, C.M.; Nikbin, K.M. [Department of Mechanical Engineering, Imperial College London, United Kindom (United Kingdom)

    2010-10-15

    In this review article, we examine the influence of prior deformation (prestrain) on the subsequent high temperature mechanical behaviour of engineering alloys. We review the observed effects at a macroscopic level in terms of creep deformation, creep rupture times and crack growth rates from a number of sources and a range of materials. Microstructural explanations for the observed macroscopic effects are also reviewed and constitutive models which incorporate the effect of prior deformation are examined. The emphasis in the paper is on engineering steels though reference is also made to non-ferrous alloys.

  18. Assessment of Deformation of Shear Localized Chip in High Speed Machining

    Institute of Scientific and Technical Information of China (English)

    T; C; LEE; W; S; LAU; S; K; CHAN

    2002-01-01

    As the cutting speed goes higher, the mechanism of chip deformation will be changed significantly, i.e., continuous chip in low cutting speed will shift to serrated chip with shear localization. For the shear localized chip, the parameters used to assess the chip deformation for continuous chip, such as shorten coefficient ξ, shear angle φ and shear strain ε, can not describe the chip deformation correctly or comprehensively. This paper deals with the assessment of chip deformation of shear localization. Th...

  19. Deformation and failure of OFHC copper under high strain rate shear compression

    Science.gov (United States)

    Ruggiero, Andrew; Testa, Gabriel; Bonora, Nicola; Iannitti, Gianluca; Persechino, Italo; Colliander, Magnus Hörnqvist

    2017-01-01

    Hat-shaped specimen geometries were developed to generate high strain, high-strain-rates deformation under prescribed conditions. These geometries offer also the possibility to investigate the occurrence of ductile rupture under low or negative stress triaxiality, where most failure models fail. In this work, three tophat geometries were designed, by means of extensive numerical simulation, to obtain desired stress triaxiality values within the shear region that develops across the ligament. Material failure was simulated using the Continuum Damage Model (CDM) formulation with a unilateral condition for damage accumulation and validated by comparing with quasi-static and high strain rate compression tests results on OFHC copper. Preliminary results seem to indicate that ductile tearing initiates at the specimen corner location where positive stress triaxiality occurs because of local rotation and eventually propagates along the ligament.

  20. Flow Behavior and Evolution of Microstructure during Hot Deformation for a High Mo Stainless Steel

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The mechanical behaviors of high Mo austenitic stainless steel 00Cr20Ni18Mo6Cu[N] have been investigated using the methods of hot compression simulation test on the Thermecmaster-Z simulator. The dynamic recrystallization kinetic equation was established, Avrami coefficient n lies in between 0.9~2 depending on deformation parameters. A perfect flow stress model considering dynamic recrystallization was also established. Dynamic recrystallization tends to complete at 1050℃ and high strain rate, but at temperature below 950℃, it is hard to occur. Double-stage interrupt compression tests were carried out. Activation energy for static and metadynamic recrystallization have been obtained respectively (QSRX=483.7, QMDRX=253.5 k J/mol). Avrami coefficient of MDRX is about 0.5, and t0.5-kinetics equations of SRX and MDRX have also been constructed. The evolution of microstructures during interrupt compression deformation was investigated. Static and metadynamic recrystallizationis essential to improve plasticity, at temperature above 1000℃ increasing interpass time has advantage for static and metadynamic recrystallization.

  1. Highly Stretchable Superhydrophobic Composite Coating Based on Self-Adaptive Deformation of Hierarchical Structures.

    Science.gov (United States)

    Hu, Xin; Tang, Changyu; He, Zhoukun; Shao, Hong; Xu, Keqin; Mei, Jun; Lau, Woon-Ming

    2017-05-01

    With the rapid development of stretchable electronics, functional textiles, and flexible sensors, water-proof protection materials are required to be built on various highly flexible substrates. However, maintaining the antiwetting of superhydrophobic surface under stretching is still a big challenge since the hierarchical structures at hybridized micro-nanoscales are easily damaged following large deformation of the substrates. This study reports a highly stretchable and mechanically stable superhydrophobic surface prepared by a facile spray coating of carbon black/polybutadiene elastomeric composite on a rubber substrate followed by thermal curing. The resulting composite coating can maintain its superhydrophobic property (water contact angle ≈170° and sliding angle superhydrophobic property. Furthermore, the experimental observation and modeling analysis reveal that the stable superhydrophobic properties of the composite coating are attributed to the unique self-adaptive deformation ability of 3D hierarchical roughness of the composite coating, which delays the Cassie-Wenzel transition of surface wetting. In addition, it is first observed that the damaged coating can automatically recover its superhydrophobicity via a simple stretching treatment without incorporating additional hydrophobic materials. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Transformation,Deformation and Microstructure Characteristics of Ru50Ta50 High Temperature Shape Memory Alloy

    Institute of Scientific and Technical Information of China (English)

    Zhirong HE; Fang WANG; Jing'en ZHOU

    2006-01-01

    The basic martensitic transformation(MT)properties of Ru50Ta50 alloy, i.e. MT temperature(MTT), temperature hysteresis(△T), and MT heat(△H)were investigated in this paper. The effects of heat treatment and thermal cycling on MT behavior of Ru50Ta50 alloy, the deformation and microstructure characteristics of Ru50Ta50 alloy were also studied for its engineering application as high temperature actuator/sensor materials by means of differential scanning calorimetry, X-ray diffraction, transmission electron microscope, optical microscope, and hardness test. The results showed that a two-stage reversible MT takes place in Ru50Ta50 alloy.The two-stage MT starting temperatures(M1s, M2s)and the temperature hysteresis(△T1, △T2)are 1047,784 and 11, 14℃, respectively. No significant effect of aging treatment and thermal cycling on MTT and △T of Ru50Ta50 alloy were observed, but △H decreases slowly with increasing thermal cycles. The hardness and brittleness of Ru50Ta50 alloy are high. The deformation mode of RuTa alloys is twinning.

  3. Effects of Adiabatic Heating on the High Strain Rate Deformation of Polymer Matrix Composites

    Science.gov (United States)

    Sorini, Chris; Chattopadhyay, Aditi; Goldberg, Robert K.

    2017-01-01

    Polymer matrix composites (PMCs) are increasingly being used in aerospace structures that are expected to experience complex dynamic loading conditions throughout their lifetime. As such, a detailed understanding of the high strain rate behavior of the constituents, particularly the strain rate, temperature, and pressure dependent polymer matrix, is paramount. In this paper, preliminary efforts in modeling experimentally observed temperature rises due to plastic deformation in PMCs subjected to dynamic loading are presented. To this end, an existing isothermal viscoplastic polymer constitutive formulation is extended to model adiabatic conditions by incorporating temperature dependent elastic properties and modifying the components of the inelastic strain rate tensor to explicitly depend on temperature. It is demonstrated that the modified polymer constitutive model is capable of capturing strain rate and temperature dependent yield as well as thermal softening associated with the conversion of plastic work to heat at high rates of strain. The modified constitutive model is then embedded within a strength of materials based micromechanics framework to investigate the manifestation of matrix thermal softening, due to the conversion of plastic work to heat, on the high strain rate response of a T700Epon 862 (T700E862) unidirectional composite. Adiabatic model predictions for high strain rate composite longitudinal tensile, transverse tensile, and in-plane shear loading are presented. Results show a substantial deviation from isothermal conditions; significant thermal softening is observed for matrix dominated deformation modes (transverse tension and in-plane shear), highlighting the importance of accounting for the conversion of plastic work to heat in the polymer matrix in the high strain rate analysis of PMC structures.

  4. Comparison of microstructures in electroformed and spin-formed copper liners of shaped charge undergone high-strain-rate deformation

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The as-formed and post-deformed microstructures in both electroformed and spin-formed copper liners of shaped charge were studied by optical microscopy(OM), electron backscattering Kikuchi patterns(EBSP) technique and transmission electron microscopy(TEM). The deformation was carried out at an ultra-high strain rate. OM analysis shows that the initial grains of the electroformed copper liner are finer than those of the spin-formed copper liners. Meanwhile, EBSP analysis reveals that the fiber texture exists in the electroformed copper liners, whereas there is no texture observed in the spin-formed copper liners before deformation. Having undergone high-strain-rate deformation the grains in the recovered slugs, which are transformed from both the electroformed and spin-formed copper liners, all become small. TEM observations of the above two kinds of post-deformed specimens show the existence of cellular structures characterized by tangled dislocations and subgrain boundaries consisting of dislocation arrays. These experimental results indicate that dynamic recovery and recrystallization play an important role in the high-strain-rate deformation process.

  5. On the response of Escherichia coli to high rates of deformation

    Science.gov (United States)

    Fitzmaurice, B. C.; Painter, J. D.; Appleby-Thomas, G. J.; Wood, D. C.; Hazael, R.; McMillan, P. F.

    2017-01-01

    While a large body of work exists on the low strain-rate loading of biological systems such as bacteria, there is a paucity of information on the response of such organisms at high rates of deformation. Here, the response of a readily accessible strain of bacteria, Escherichia coli (E. coli), has been examined under shock loading conditions. Although previous studies have shown greatly reduced growth in shock conditions up to several GPa, relationships between loading conditions and bacterial response have yet to be fully elucidated. Initial results of a more rigorous investigation into the 1D shock loading response of E. coli are presented here, expectantly leading to a more comprehensive view of its behaviour when exposed to high pressures. Comparison has been drawn to provide insight into the importance of the nature of the loading regime to the survival of these biological systems.

  6. A New High-Resolution Spectral Approach to Noninvasively Evaluate Wall Deformations in Arteries

    Directory of Open Access Journals (Sweden)

    Ivonne Bazan

    2014-01-01

    Full Text Available By locally measuring changes on arterial wall thickness as a function of pressure, the related Young modulus can be evaluated. This physical magnitude has shown to be an important predictive factor for cardiovascular diseases. For evaluating those changes, imaging segmentation or time correlations of ultrasonic echoes, coming from wall interfaces, are usually employed. In this paper, an alternative low-cost technique is proposed to locally evaluate variations on arterial walls, which are dynamically measured with an improved high-resolution calculation of power spectral densities in echo-traces of the wall interfaces, by using a parametric autoregressive processing. Certain wall deformations are finely detected by evaluating the echoes overtones peaks with power spectral estimations that implement Burg and Yule Walker algorithms. Results of this spectral approach are compared with a classical cross-correlation operator, in a tube phantom and “in vitro” carotid tissue. A circulating loop, mimicking heart periods and blood pressure changes, is employed to dynamically inspect each sample with a broadband ultrasonic probe, acquiring multiple A-Scans which are windowed to isolate echo-traces packets coming from distinct walls. Then the new technique and cross-correlation operator are applied to evaluate changing parietal deformations from the detection of displacements registered on the wall faces under periodic regime.

  7. Feasible optimal deformable mirror shaping algorithm for high-contrast imaging

    Science.gov (United States)

    Give'on, Amir; Kasdin, N. Jeremy; Vanderbei, Robert J.; Spergel, David N.; Littman, Michael G.; Gurfil, Pini

    2003-12-01

    The Princeton University Terrestrial Planet Finder (TPF) group has been working on a novel method for direct imaging of extra solar planets using a shaped-pupil coronagraph. The entrance pupil of the coronagraph is optimized to have a point spread function (PSF) that provides the suppression level needed at the angular separation required for detection of extra solar planets. When integration time is to be minimized, the photon count at the planet location in the image plane is a Poisson distributed random process. The ultimate limitation of these high-dynamic-range imaging systems comes from scattering due to imperfections in the optical surfaces of the collecting system. The first step in correcting the wavefront errors is the estimation of the phase aberrations. The phase aberration caused by these imperfections is assumed to be a sum of two-dimensional sinusoidal functions. Assuming one uses a deformable mirror to correct these aberrations, we propose an algorithm that optimally decreases the scattering level in specified localized areas in the image plane independent of the choice of influence function of the deformable mirror.

  8. High purity ultrafine-grained nickel processed by dynamic plastic deformation: microstructure and mechanical properties

    Energy Technology Data Exchange (ETDEWEB)

    Farbaniec, Lukasz; Dirras, Guy [Universite Paris 13, Sorbonne Paris Cite LSPM-CNRS, 99, Avenue J. B. Clement, 93430 Villetaneuse (France); Abdul-Latif, Akrum [Laboratoire d' Ingenierie des Systemes Mecaniques et des Materiaux 3, Rue Fernand Hainaut, 93407 St. Ouen Cedex (France); Gubicza, Jeno [Department of Materials Physics, Eoetvoes Lorand University Budapest, P.O. Box 32, H-1518 (Hungary)

    2012-11-15

    Bulk ultrafine-grained samples are processed by dynamic plastic deformation at an average strain rate of 3.3 x 10{sup 2} s{sup -1} from bulk coarse-grained nickel with purity higher than 98.4 wt.%. The obtained microstructure is investigated by electron backscattering diffraction, transmission electron microscopy and X-ray line profile analysis. After dynamic deformation the microstructure evolves into submicron-size lamellar and subgrain structures. Evaluation of average grain size shows a heterogeneous microstructure along both the diameter and the thickness of the sample. X-ray line profile analysis reveals high dislocation density of about 13 {+-} 2 x 10{sup 14} m{sup -2} in the impacted material. The mechanical properties are investigated by means of uniaxial quasi-static compression tests conducted at room temperature. The stress-strain behavior of the impacted Ni depends on the location in the impacted disk and on the orientation of the compression axis relative to the impact direction. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Tensile deformation and fracture behavior of CuZn5 brass alloy at high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Sharififar, M., E-mail: m.sharififar@ut.ac.ir; Akbari Mousavi, S.A.A., E-mail: akbarimusavi@ut.ac.ir

    2014-01-31

    Alpha brass alloys are widely used for production of rectangular waveguides because of their low bulk resistivity. In this paper, the microstructure, tensile deformation and fracture behavior of CuZn5 brass alloy were investigated. The strain rate sensitivity and its relation to post-uniform deformation in tensile test and correlation between strain hardening exponent (n) and temperature were examined. The results show that strain hardening exponent decreases from 0.5 to 0.4 with increase in test temperature from 250 to 450 °C. Tensile fracture mechanisms of as-extruded CuZn5 brass alloy were studied over a range of temperatures from 300 to 450 °C and range of strain rates from 0.01 to 0.4 1/s by means of scanning electron microscope (SEM) and Atomic Force Microscope (AFM). The results show that different fracture mechanisms operate in different temperature and strain rate ranges. While transgranular dimple fracture is dominant at 300 °C and 0.4 1/s, the dominant fracture mechanism at 450 °C and 0.01 1/s is cleavage facets. Precipitations and grain boundary sliding at high temperature may be the mechanism of ductility drop. Dynamic strain ageing (DSA) did not occur since none of the manifestations of DSA are observed.

  10. Deformation of Cases in High Capacitance Value Wet Tantalum Capacitors under Environmental Stresses

    Science.gov (United States)

    Teverovsky, Alexander

    2016-01-01

    Internal gas pressure in hermetic wet tantalum capacitors is created by air, electrolyte vapor, and gas generated by electrochemical reactions at the electrodes. This pressure increases substantially with temperature and time of operation due to excessive leakage currents. Deformation of the case occurs when the internal pressure exceeds pressure of the environments and can raise significantly when a part operates in space. Contrary to the cylinder case wet tantalum capacitors that have external sealing by welding and internal sealing provided by the Teflon bushing and crimping of the case, no reliable internal sealing exists in the button case capacitors. Single seal design capacitors are used for high capacitance value wet tantalum capacitors manufactured per DLA L&M drawings #04003, 04005, and 10011, and require additional analysis to assure their reliable application in space systems. In this work, leakage currents and case deformation of button case capacitors were measured during different environmental test conditions. Recommendations for derating, screening and qualification testing are given. This work is a continuation of a series of NEPP reports related to quality and reliability of wet tantalum capacitors.

  11. A New High-Resolution Spectral Approach to Noninvasively Evaluate Wall Deformations in Arteries

    Science.gov (United States)

    Bazan, Ivonne; Negreira, Carlos; Ramos, Antonio; Brum, Javier; Ramirez, Alfredo

    2014-01-01

    By locally measuring changes on arterial wall thickness as a function of pressure, the related Young modulus can be evaluated. This physical magnitude has shown to be an important predictive factor for cardiovascular diseases. For evaluating those changes, imaging segmentation or time correlations of ultrasonic echoes, coming from wall interfaces, are usually employed. In this paper, an alternative low-cost technique is proposed to locally evaluate variations on arterial walls, which are dynamically measured with an improved high-resolution calculation of power spectral densities in echo-traces of the wall interfaces, by using a parametric autoregressive processing. Certain wall deformations are finely detected by evaluating the echoes overtones peaks with power spectral estimations that implement Burg and Yule Walker algorithms. Results of this spectral approach are compared with a classical cross-correlation operator, in a tube phantom and “in vitro” carotid tissue. A circulating loop, mimicking heart periods and blood pressure changes, is employed to dynamically inspect each sample with a broadband ultrasonic probe, acquiring multiple A-Scans which are windowed to isolate echo-traces packets coming from distinct walls. Then the new technique and cross-correlation operator are applied to evaluate changing parietal deformations from the detection of displacements registered on the wall faces under periodic regime. PMID:24688596

  12. A GPU based high-resolution multilevel biomechanical head and neck model for validating deformable image registration

    Energy Technology Data Exchange (ETDEWEB)

    Neylon, J., E-mail: jneylon@mednet.ucla.edu; Qi, X.; Sheng, K.; Low, D. A.; Kupelian, P.; Santhanam, A. [Department of Radiation Oncology, University of California Los Angeles, 200 Medical Plaza, #B265, Los Angeles, California 90095 (United States); Staton, R.; Pukala, J.; Manon, R. [Department of Radiation Oncology, M.D. Anderson Cancer Center, Orlando, 1440 South Orange Avenue, Orlando, Florida 32808 (United States)

    2015-01-15

    Purpose: Validating the usage of deformable image registration (DIR) for daily patient positioning is critical for adaptive radiotherapy (RT) applications pertaining to head and neck (HN) radiotherapy. The authors present a methodology for generating biomechanically realistic ground-truth data for validating DIR algorithms for HN anatomy by (a) developing a high-resolution deformable biomechanical HN model from a planning CT, (b) simulating deformations for a range of interfraction posture changes and physiological regression, and (c) generating subsequent CT images representing the deformed anatomy. Methods: The biomechanical model was developed using HN kVCT datasets and the corresponding structure contours. The voxels inside a given 3D contour boundary were clustered using a graphics processing unit (GPU) based algorithm that accounted for inconsistencies and gaps in the boundary to form a volumetric structure. While the bony anatomy was modeled as rigid body, the muscle and soft tissue structures were modeled as mass–spring-damper models with elastic material properties that corresponded to the underlying contoured anatomies. Within a given muscle structure, the voxels were classified using a uniform grid and a normalized mass was assigned to each voxel based on its Hounsfield number. The soft tissue deformation for a given skeletal actuation was performed using an implicit Euler integration with each iteration split into two substeps: one for the muscle structures and the other for the remaining soft tissues. Posture changes were simulated by articulating the skeletal structure and enabling the soft structures to deform accordingly. Physiological changes representing tumor regression were simulated by reducing the target volume and enabling the surrounding soft structures to deform accordingly. Finally, the authors also discuss a new approach to generate kVCT images representing the deformed anatomy that accounts for gaps and antialiasing artifacts that may

  13. Evaluation of Dynamic Deformation Behaviors in Metallic Materials under High Strain-Rates Using Taylor Bar Impact Test

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Kyung Oh; Shin, Hyung Seop [Andong National Univ., Andong (Korea, Republic of)

    2016-09-15

    To ensure the reliability and safety of various mechanical systems in accordance with their high-speed usage, it is necessary to evaluate the dynamic deformation behavior of structural materials under impact load. However, it is not easy to understand the dynamic deformation behavior of the structural materials using experimental methods in the high strain-rate range exceeding 10{sup 4} s{sup -1}. In this study, the Taylor bar impact test was conducted to investigate the dynamic deformation behavior of metallic materials in the high strain-rate region, using a high-speed photography system. Numerical analysis of the Taylor bar impact test was performed using AUTODYN S/W. The results of the analysis were compared with the experimental results, and the material behavior in the high strain-rate region was discussed.

  14. Analysis on Shear Deformation for High Manganese Austenite Steel during Hot Asymmetrical Rolling Process Using Finite Element Method

    Institute of Scientific and Technical Information of China (English)

    Feng-li SUI; Xin WANG; Jun ZHAO; Biao MA; Chang-sheng LI

    2015-01-01

    Based on the rigid-plastic ifnite element method (FEM), the shear stress ifeld of deformation region for high manganese austenite steel during hot asymmetrical rolling process was analyzed. The inlfuences of rolling parameters, such as thevelocity ratio of upper to lower rolls, theinitial temperature of workpiece and the reduction rate, on the shear deformation of three nodes in the upper, center and lower layers were discussed. As the rolling parameters change, distinct shear deformation appears in the up-per and lower layers, but the shear deformation in the center layer appears only when the velocity ratio is more than 1.00, and the absolute value of the shear stress in this layer is changed with rolling parameters. A mathematical model which relfected the change of the maximal absolute shear stress for the center layer was established, by which the maximal absolute shear stress for the center layer can be easily calculated and the appropriate rolling technology can be designed.

  15. Dynamic tensile deformation and fracture of a highly particle-filled composite using SHPB and high-speed DIC method

    Directory of Open Access Journals (Sweden)

    Huang F.

    2012-08-01

    Full Text Available In this work, various tensile tests, including Brazilian disc test (BDT, flattened Brazilian disc (FBD test and semi-circular bending (SCB test, were carried out on a highly particle-filled composite by using a split Hopkinson pressure bar (SHPB. With the consideration of low strength and low wave impedance of the materials, a quartz crystal transducer was embedded in SHPB to measure the loading forces. A high-speed camera was used to capture the deformation and fracture process of materials. Digital image correlation (DIC method was used to process these digital images to obtain the dynamic deformation information. Based on the measured strain fields, the crack growth path was determined and the failure mechanism of samples was analyzed. Combining SHPB and DIC method, the indirect tensile stress strain plots of disc samples were obtained, and the dynamic fracture toughness of materials was measured using both FBD and SCB tests. The results show that the tensile failure strength and fracture toughness increases with the increase of strain rates, exhibiting strain rate dependence. The high-speed DIC method combined with SHPB is effective to study the dynamic tensile behaviour of brittle materials with low strengths.

  16. Dynamic tensile deformation and fracture of a highly particle-filled composite using SHPB and high-speed DIC method

    Science.gov (United States)

    Zhou, Z.; Chen, P.; Guo, B.; Huang, F.

    2012-08-01

    In this work, various tensile tests, including Brazilian disc test (BDT), flattened Brazilian disc (FBD) test and semi-circular bending (SCB) test, were carried out on a highly particle-filled composite by using a split Hopkinson pressure bar (SHPB). With the consideration of low strength and low wave impedance of the materials, a quartz crystal transducer was embedded in SHPB to measure the loading forces. A high-speed camera was used to capture the deformation and fracture process of materials. Digital image correlation (DIC) method was used to process these digital images to obtain the dynamic deformation information. Based on the measured strain fields, the crack growth path was determined and the failure mechanism of samples was analyzed. Combining SHPB and DIC method, the indirect tensile stress strain plots of disc samples were obtained, and the dynamic fracture toughness of materials was measured using both FBD and SCB tests. The results show that the tensile failure strength and fracture toughness increases with the increase of strain rates, exhibiting strain rate dependence. The high-speed DIC method combined with SHPB is effective to study the dynamic tensile behaviour of brittle materials with low strengths.

  17. Internal deformation in layered Zechstein-III K-Mg salts. Structures formed by complex deformation and high contrasts in viscosity observed in drill cores.

    Science.gov (United States)

    Raith, Alexander; Urai, Janos L.

    2016-04-01

    During the evaporation of a massive salt body, alternations of interrupted and full evaporation sequences can form a complex layering of different lithologies. Viscosity contrasts of up to five orders of magnitude between these different lithologies are possible in this environment. During the late stage of an evaporation cycle potassium and magnesium (K-Mg) salts are precipitated. These K-Mg salts are of economic interest but also a known drilling hazard due to their very low viscosity. How up to 200m thick layers of these evaporites affect salt deformation at different scales is not well known. A better understanding of salt tectonics with extreme mechanical stratification is needed for better exploration and production of potassium-magnesium salts and to predict the internal structure of potential nuclear waste repositories in salt. To gain a better understanding of the internal deformation of these layers we analyzed K-Mg salt rich drill cores out of the Zechstein III-1b subunit from the Veendam Pillow 10 km southeast of Groningen, near the city Veendam in the NE Netherlands. The study area has a complex geological history with multiple tectonic phases of extension and compression forming internal deformation in the pillow but also conserving most of the original layering. Beside halite the most common minerals in the ZIII-1b are carnallite, kieserite, anhydrite and bischofite alternating in thin layers of simple composition. Seismic interpretation revealed that the internal structure of the Veendam Pillow shows areas, in which the K-Mg salt rich ZIII 1b layer is much thicker than elsewhere, as a result of salt deformation. The internal structure of the ZIII-1b on the other hand, remains unknown. The core analysis shows a strong strain concentration in the weaker Bischofite (MgCl2*6H20) and Carnallite (KMgCl3*6H20) rich layers producing tectonic breccias and highly strained layers completely overprinting the original layering. Layers formed by alternating beds

  18. The Long-Term Settlement Deformation Automatic Monitoring System for the Chinese High-Speed Railway

    Directory of Open Access Journals (Sweden)

    Xu Wang

    2015-01-01

    Full Text Available The Beijing-Shanghai high-speed railway is one of the milestones of China’s high-speed railway development and its security plays a significant role in China’s economic and social development. However, the evaluation methods used for large-scale security operations and important infrastructure systems, such as the high-speed railways, are discrete and nonlinear; thus they cannot issue emergency warnings in a timely manner. The emergence of optical fiber sensing technology can solve this problem. This technology has progressed rapidly in its application to the monitoring of railway security and it has attracted much attention within the industry. This study considers the newly built passenger railway line between Shijiazhuang and Jinan as an example. The web-based, all-in-one fiber Bragg grating static level is described as well as a set of online monitoring systems, which is automated, real-time, remote, visual, and adaptable to the standards of the Beijing-Shanghai high-speed railway. According to our theoretical analysis, the planned automated monitoring of settlement deformation for the Beijing-Shanghai high-speed railway and the real-time analysis and calculation of monitoring data can ensure the operational security of this section of China’s high-speed railway system.

  19. Deformation at ambient and high temperature of in situ Laves phases-ferrite composites.

    Science.gov (United States)

    Donnadieu, Patricia; Pohlmann, Carsten; Scudino, Sergio; Blandin, Jean-Jacques; Babu Surreddi, Kumar; Eckert, Jürgen

    2014-06-01

    The mechanical behavior of a Fe80Zr10Cr10 alloy has been studied at ambient and high temperature. This Fe80Zr10Cr10 alloy, whoose microstructure is formed by alternate lamellae of Laves phase and ferrite, constitutes a very simple example of an in situ CMA phase composite. The role of the Laves phase type was investigated in a previous study while the present work focuses on the influence of the microstructure length scale owing to a series of alloys cast at different cooling rates that display microstructures with Laves phase lamellae width ranging from ∼50 nm to ∼150 nm. Room temperature compression tests have revealed a very high strength (up to 2 GPa) combined with a very high ductility (up to 35%). Both strength and ductility increase with reduction of the lamella width. High temperature compression tests have shown that a high strength (900 MPa) is maintained up to 873 K. Microstructural study of the deformed samples suggests that the confinement of dislocations in the ferrite lamellae is responsible for strengthening at both ambient and high temperature. The microstructure scale in addition to CMA phase structural features stands then as a key parameter for optimization of mechanical properties of CMA in situ composites.

  20. Combinational-deformable-mirror adaptive optics system for compensation of high-order modes of wavefront

    Institute of Scientific and Technical Information of China (English)

    Huafeng Yang; Guilin Liu; Changhui Rao; Yudong Zhang; Wenhan Jiang

    2007-01-01

    A new kind of adaptive optics (AO) system, in which several low spatial frequency deformable mirrors(DMs) with optical conjugation relationship are combined to correct high-order aberrations, is proposed.The phase compensation principle and the control method of the combinational AO system are introduced.The numerical simulations for the AO system with two 60-element DMs are presented. The results indicate that the combinational DM in the AO system can correct different aberrations effectively as one single DM with more actuators, and there is no change of control method. This technique can be applied to a large telescope AO system to improve the spatial compensation capability for wavefront by using current DM.

  1. Defects interaction processes in deformed high purity polycrystalline molybdenum at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Lambri, O.A., E-mail: olambri@fceia.unr.edu.ar [Laboratorio de Materiales, Escuela de Ingeniería Eléctrica, Centro de Tecnología e Investigación Eléctrica, Facultad de Ciencias Exactas, Ingeniería y Agrimensura, Universidad Nacional de Rosario – CONICET, Avda. Pellegrini 250, (2000) Rosario (Argentina); Bonifacich, F.G. [Laboratorio de Materiales, Escuela de Ingeniería Eléctrica, Centro de Tecnología e Investigación Eléctrica, Facultad de Ciencias Exactas, Ingeniería y Agrimensura, Universidad Nacional de Rosario – CONICET, Avda. Pellegrini 250, (2000) Rosario (Argentina); Bozzano, P.B. [Laboratorio de Microscopía Electrónica, Unidad de Actividad Materiales, Centro Atómico Constituyentes, Comisión Nacional de Energía Atómica e Instituto Sábato – Universidad Nacional de San Martín, Avda. Gral. Paz 1499, (1650) San Martín (Argentina); Zelada, G.I. [Laboratorio de Materiales, Escuela de Ingeniería Eléctrica, Centro de Tecnología e Investigación Eléctrica, Facultad de Ciencias Exactas, Ingeniería y Agrimensura, Universidad Nacional de Rosario – CONICET, Avda. Pellegrini 250, (2000) Rosario (Argentina); and others

    2014-10-15

    Mechanical spectroscopy (damping and elastic modulus as a function of temperature) and transmission electron microscopy studies have been performed in high purity polycrystalline molybdenum plastically deformed to different values of tensile and torsion strain. Mechanical spectroscopy measurements were performed from room temperature up to 1285 K. A relaxation peak in polycrystalline molybdenum related to the movement of dislocations into lower energy configurations near grain boundaries has been discovered to appear around 1170 K. The activation energy of the peak is 4.2 eV ± 0.5 eV. This relaxation phenomenon involves the interaction between vacancies and mobile dislocations near the grain boundaries. It should be highlighted that this relaxation process is controlled by the arrangement of vacancies and dislocations which occur at temperature below 1070 K.

  2. FE Analysis on Shear Deformation for Asymmetrically Hot-Rolled High-Manganese Steel Strip

    Science.gov (United States)

    Sui, Feng-Li; Wang, Xin; Li, Chang-Sheng; Zhao, Jun

    2016-09-01

    Shear deformation along the longitudinal cross section of the high-manganese steel strip has been analyzed in hot asymmetrical rolling process using rigid-plastic finite element model. The friction coefficient between the rolls and the strip surfaces, the diameter of the work rolls, the speed ratio for the lower/upper rolls, the reduction rate and the initial temperature of the billet were all taken into account. Influence of these process parameters on the shear stress, the shear strain and the related shear strain energy in the center layer of the hot-rolled strip was analyzed. It is indicated that increasing the speed ratio, the reduction rate and the work roll diameter is an effective way to accumulate more shear strain energy in the strip center. A mathematical model reflecting the relationship between the shear strain energy and the process parameters has been established.

  3. Hot deformation mechanism and microstructure evolution of an ultra-high nitrogen austenitic steel containing Nb and V

    Institute of Scientific and Technical Information of China (English)

    Rong-hua Zhang; Ze-an Zhou; Ming-wei Guo; Jian-jun Qi; Shu-hua Sun; Wan-tang Fu

    2015-01-01

    The flow curves of an ultra-high nitrogen austenitic steel containing niobium (Nb) and vanadium (V) were obtained by hot com-pression deformation at temperatures ranging from 1000℃ to 1200℃ and strain rates ranging from 0.001 s?1 to 10 s?1. The mechanical be-havior during hot deformation was discussed on the basis of flow curves and hot processing maps. The microstructures were analyzed via scanning electron microscopy and electron backscatter diffraction. The relationship between deformation conditions and grain size after dy-namic recrystallization was obtained. The results show that the flow stress and peak strain both increase with decreasing temperature and in-creasing strain rate. The hot deformation activation energy is approximately 631 kJ/mol, and a hot deformation equation is proposed. (Nb,V)N precipitates with either round, square, or irregular shapes are observed at the grain boundaries and in the matrix after deformation. According to the discussion, the hot working should be processed in the temperature range of 1050℃ to 1150℃ and in the strain rate range of 0.01 to 1 s?1.

  4. Deformation and Phase Transformation Processes in Polycrystalline NiTi and NiTiHf High Temperature Shape Memory Alloys

    Science.gov (United States)

    Benafan, Othmane

    2012-01-01

    The deformation and transformation mechanisms of polycrystalline Ni49.9Ti50.1 and Ni50.3Ti29.7Hf20 (in at.%) shape memory alloys were investigated by combined experimental and modeling efforts aided by an in situ neutron diffraction technique at stress and temperature. The thermomechanical response of the low temperature martensite, the high temperature austenite phases, and changes between these two states during thermomechanical cycling were probed and reported. In the cubic austenite phase, stress-induced martensite, deformation twinning and slip processes were observed which helped in constructing a deformation map that contained the limits over which each of the identified mechanisms was dominant. Deformation of the monoclinic martensitic phase was also investigated where the microstructural changes (texture, lattice strains, and phase fractions) during room-temperature deformation and subsequent thermal cycling were compared to the bulk macroscopic response. When cycling between these two phases, the evolution of inelastic strains, along with the shape setting procedures were examined and used for the optimization of the transformation properties as a function of deformation levels and temperatures. Finally, this work was extended to the development of multiaxial capabilities at elevated temperatures for the in situ neutron diffraction measurements of shape memory alloys on the VULCAN Diffractometer at Oak Ridge National Laboratory.

  5. Finite element analysis on deformation of high embankment in heavy-haul railway subjected to freeze-thaw cycles

    Institute of Scientific and Technical Information of China (English)

    ChengYi Yu; Shuang Tian; Liang Tang; XianZhang Ling; GuoQing Zhou

    2015-01-01

    Finite element simulations are increasingly providing a versatile environment for this topic. In this study, a two-dimensional finite element analysis is conducted to predict the deformation of high embankment in Bazhun heavy-haul railway, China. A recently developed nonlinear softening-type constitutive model is utilized to model the be-havior of subgrade filling materials subjected to freeze-thaw cycles. For the convenience of practical application, the dynamic loading induced by a vehicle is treated as a quasi-static axle load. The deformation of this embankment with different moisture content under freeze-thaw cycles is compared. The results show that when subjected to the first freeze-thaw cycle, the embankment experienced significant deformation variations. Maximum deformation was usually achieved after the embankment with optimum moisture content experienced six freeze-thaw cycles, however, the em-bankment with moisture content of 8.0% and 9.5% deforms continuously even after experiencing almost ten freeze-thaw cycles. Overall, this study provides a simple nonlinear finite element approach for calculating the deformation of the embankment in changing climate conditions.

  6. Strength variation and deformational behavior in anisotropic granitic mylonites under high-temperature and -pressure conditions - An experimental study

    Science.gov (United States)

    Liu, Gui; Zhou, Yongsheng; Shi, Yaolin; Miao, Sheqiang; He, Changrong

    2017-03-01

    We performed deformation experiments on foliated granitic mylonites under high-temperature and -pressure conditions. To investigate the effects of pre-existing fabric properties on the rheology of the rocks, these experiments were carried out at different compression directions 30°, 45°, and 60° relative to the foliation, at temperatures of 600-850 °C, under confining pressures of 800-1200 MPa, within a strain rate range of 1 × 10-4/S - 2.5 × 10-6/S. The results of the experiments show that the deformation of three group samples is in the semi-brittle region at temperatures between 600 and 700 °C, and that the deformation of the samples transforms to plastic deformation by power-law creep with the stress exponent n = 3 ± 0.3 at temperatures between 800 and 850 °C. In the semi-brittle region, the mechanical data show that strength reaches its minimum value at an angle of 30° between the compression direction and the original foliation. In the plastic deformation regime, strength reaches its minimum value at an angle of 45° between the foliation and the orientation of the maximum principal stress. The strength with angles between 30° and 60° is lower than that of the compression direction perpendicular to foliation and the compression direction parallel to foliation. Microstructure analysis based on optical and electron microscopy of the deformation microstructures showed plastic deformation of aggregates of biotite and quartz at 800-850 °C. This deformation was extensive and formed new foliation. Quartz c-axis fabrics analysis by EBSD show that at temperatures of 600-700 °C, the c-axis fabric patterns could have been formed by the dominant activity of basal slip, similar with the starting granitic mylonite samples, but the dominant slip systems have been changed and transformed from basal slip to rhomb slip and prism slip at temperature of 800 °C and 850 °C. Microfractures were developed in hornblende and feldspar grains with local plastic

  7. Deformation microstructures

    DEFF Research Database (Denmark)

    Hansen, N.; Huang, X.; Hughes, D.A.

    2004-01-01

    Microstructural characterization and modeling has shown that a variety of metals deformed by different thermomechanical processes follows a general path of grain subdivision, by dislocation boundaries and high angle boundaries. This subdivision has been observed to very small structural scales...... of the order of 10 nm, produced by deformation under large sliding loads. Limits to the evolution of microstructural parameters during monotonic loading have been investigated based on a characterization by transmission electron microscopy. Such limits have been observed at an equivalent strain of about 10...

  8. GNSS seismometer: Seismic phase recognition of real-time high-rate GNSS deformation waves

    Science.gov (United States)

    Nie, Zhaosheng; Zhang, Rui; Liu, Gang; Jia, Zhige; Wang, Dijin; Zhou, Yu; Lin, Mu

    2016-12-01

    High-rate global navigation satellite systems (GNSS) can potentially be used as seismometers to capture short-period instantaneous dynamic deformation waves from earthquakes. However, the performance and seismic phase recognition of the GNSS seismometer in the real-time mode, which plays an important role in GNSS seismology, are still uncertain. By comparing the results of accuracy and precision of the real-time solution using a shake table test, we found real-time solutions to be consistent with post-processing solutions and independent of sampling rate. In addition, we analyzed the time series of real-time solutions for shake table tests and recent large earthquakes. The results demonstrated that high-rate GNSS have the ability to retrieve most types of seismic waves, including P-, S-, Love, and Rayleigh waves. The main factor limiting its performance in recording seismic phases is the widely used 1-Hz sampling rate. The noise floor also makes recognition of some weak seismic phases difficult. We concluded that the propagation velocities and path of seismic waves, macro characteristics of the high-rate GNSS array, spatial traces of seismic phases, and incorporation of seismographs are all useful in helping to retrieve seismic phases from the high-rate GNSS time series.

  9. Mechanical properties and constitutive relations for tantalum and tantalum alloys under high-rate deformation

    Energy Technology Data Exchange (ETDEWEB)

    Chen, S.R.; Gray, G.T. III; Bingert, S.R. [Los Alamos National Lab., NM (United States). Materials Science and Technology Div.

    1996-05-01

    Tantalum and its alloys have received increased interest as a model bcc metal and for defense-related applications. The stress-strain behavior of several tantalums, possessing varied compositions and manufacturing histories, and tantalum alloyed with tungsten, was investigated as a function of temperature from {minus}196 C to 1,000 C, and strain rate from 10{sup {minus}3} s{sup {minus}1} to 8,000 s{sup {minus}1}. The yield stress for all the Ta-materials was found to be sensitive to the test temperature, the impurity and solute contents; however, the strain hardening remained very similar for various ``pure`` tantalums but increased with alloying. Powder-metallurgy (P/M) tantalum with various levels of oxygen content produced via different processing paths was also investigated. Similar mechanical properties compared to conventionally processed tantalums were achieved in the P/M Ta. This data suggests that the frequently observed inhomogeneities in the mechanical behavior of tantalum inherited from conventional processes can be overcome. Constitutive relations based upon the Johnson-Cook, the Zerilli-Armstrong, and the Mechanical Threshold Stress models were evaluated for all the Ta-based materials. Parameters were also fit for these models to a tantalum-bar material. Flow stresses of a Ta bar stock subjected to a large-strain deformation of {var_epsilon} = 1.85 via multiple upset forging were obtained. The capabilities and limitations of each model for large-strain applications are examined. The deformation mechanisms controlling high-rate plasticity in tantalum are revisited.

  10. High temperature deformation behavior, thermal stability and irradiation performance in Grade 92 steel

    Science.gov (United States)

    Alsagabi, Sultan

    The 9Cr-2W ferritic-martensitic steel (i.e. Grade 92 steel) possesses excellent mechanical and thermophysical properties; therefore, it has been considered to suit more challenging applications where high temperature strength and creep-rupture properties are required. The high temperature deformation mechanism was investigated through a set of tensile testing at elevated temperatures. Hence, the threshold stress concept was applied to elucidate the operating high temperature deformation mechanism. It was identified as the high temperature climb of edge dislocations due to the particle-dislocation interactions and the appropriate constitutive equation was developed. In addition, the microstructural evolution at room and elevated temperatures was investigated. For instance, the microstructural evolution under loading was more pronounced and carbide precipitation showed more coarsening tendency. The growth of these carbide precipitates, by removing W and Mo from matrix, significantly deteriorates the solid solution strengthening. The MX type carbonitrides exhibited better coarsening resistance. To better understand the thermal microstructural stability, long tempering schedules up to 1000 hours was conducted at 560, 660 and 760°C after normalizing the steel. Still, the coarsening rate of M23C 6 carbides was higher than the MX-type particles. Moreover, the Laves phase particles were detected after tempering the steel for long periods before they dissolve back into the matrix at high temperature (i.e. 720°C). The influence of the tempering temperature and time was studied for Grade 92 steel via Hollomon-Jaffe parameter. Finally, the irradiation performance of Grade 92 steel was evaluated to examine the feasibility of its eventual reactor use. To that end, Grade 92 steel was irradiated with iron (Fe2+) ions to 10, 50 and 100 dpa at 30 and 500°C. Overall, the irradiated samples showed some irradiation-induced hardening which was more noticeable at 30°C. Additionally

  11. Formation of defects at high temperature plastic deformation of gallium arsenide

    Energy Technology Data Exchange (ETDEWEB)

    Mikhnovich, V.V.

    2006-03-14

    The purpose of the present thesis consists in acquiring more concrete information concerning the mechanism of the movement of dislocations and types of defects that appear during the process of dislocation motion on the basis of systematic experimental studies of the GaAs deformation. Experimental studies concerning the dependence of the stress of the samples from their deformation at different values of the deformation parameters (like temperature and deformation speed) were conducted in this paper. To determine the concentration of defects introduced in samples during the deformation process the positron annihilation spectroscopy (PAS) method was used. The second chapter of this paper deals with models of movement of dislocations and origination of defects during deformation of the samples. In the third chapter channels and models of positron annihilation in the GaAs samples are investigated. In the forth chapter the used experimental methods, preparation procedure of test samples and technical data of conducted experiments are described. The fifth chapter shows the results of deformation experiments. The sixth chapter shows the results of positron lifetime measurements by the PAS method. In the seventh chapter one can find analyses of the values of defects concentration that were introduced in samples during deformation. (orig.)

  12. Deformation behavior of duplex austenite and ε-martensite high-Mn steel

    Directory of Open Access Journals (Sweden)

    Ki Hyuk Kwon, Byeong-Chan Suh, Sung-Il Baik, Young-Woon Kim, Jong-Kyo Choi and Nack J Kim

    2013-01-01

    Full Text Available Deformation and work hardening behavior of Fe–17Mn–0.02C steel containing ε-martensite within the austenite matrix have been investigated by means of in situ microstructural observations and x-ray diffraction analysis. During deformation, the steel shows the deformation-induced transformation of austenite → ε-martensite → α'-martensite as well as the direct transformation of austenite → α'-martensite. Based on the calculation of changes in the fraction of each constituent phase, we found that the phase transformation of austenite → ε-martensite is more effective in work hardening than that of ε-martensite → α'-martensite. Moreover, reverse transformation of ε-martensite → austenite has also been observed during deformation. It originates from the formation of stacking faults within the deformed ε-martensite, resulting in the formation of 6H-long periodic ordered structure.

  13. Effects of contents of Nb and C on hot deformation behaviors of high Nb X80 pipeline steels

    Institute of Scientific and Technical Information of China (English)

    QIAO Gui-ying; XIAO Fu-ren; ZHANG Xiao-bing; CAO Ya-bin; LIAO Bo

    2009-01-01

    The behavior of the flow deformation and the effects of contents of Nb and C on deformation behaviors of high Nb X80 pipeline steels during hot compression deformation were studied by thermal simulation test.The content of solid solution Nb was quantificationally studied during the reheating and hot deformation process,and the effects of change of solid solution Nb in steels on hot deformation behaviors were discussed.The results show that the contents of Nb and C have great effects on the flow stress behaviors of high Nb X80 pipeline steels.When the C content in steels is constant,the recrystallization activation energy increases from 387 to 481 kJ/mol with increasing the Nb from 0.082% to 0.13% (mass fraction).However,the effect of Nb is correlative to the C content,I.e.w(Nb)/w(C).When w(Nb)/w(C) decreases from 3.61 to 2.18,the recrystallization activation energy decreases from 481 to 434 kJ/mol.

  14. In-situ tube burst testing and high-temperature deformation behavior of candidate materials for accident tolerant fuel cladding

    Science.gov (United States)

    Gussev, M. N.; Byun, T. S.; Yamamoto, Y.; Maloy, S. A.; Terrani, K. A.

    2015-11-01

    One of the most essential properties of accident tolerant fuel (ATF) for maintaining structural integrity during a loss-of-coolant accident (LOCA) is high resistance of the cladding to plastic deformation and burst failure, since the deformation and burst behavior governs the cooling efficiency of flow channels and the process of fission product release. To simulate and evaluate the deformation and burst process of thin-walled cladding, an in-situ testing and evaluation method has been developed on the basis of visual imaging and image analysis techniques. The method uses a specialized optics system consisting of a high-resolution video camera, a light filtering unit, and monochromatic light sources. The in-situ testing is performed using a 50 mm long pressurized thin-walled tubular specimen set in a programmable furnace. As the first application, ten (10) candidate cladding materials for ATF, i.e., five FeCrAl alloys and five nanostructured steels, were tested using the newly developed method, and the time-dependent images were analyzed to produce detailed deformation and burst data such as true hoop stress, strain (creep) rate, and failure stress. Relatively soft FeCrAl alloys deformed and burst below 800 °C, while negligible strain rates were measured for higher strength alloys.

  15. Monitoring and analysis of thermal deformation waves with a high-speed phase measurement system.

    Science.gov (United States)

    Taylor, Lucas; Talghader, Joseph

    2015-10-20

    Thermal effects in optical substrates are vitally important in determining laser damage resistance in long-pulse and continuous-wave laser systems. Thermal deformation waves in a soda-lime-silica glass substrate have been measured using high-speed interferometry during a series of laser pulses incident on the surface. Two-dimensional images of the thermal waves were captured at a rate of up to six frames per thermal event using a quantitative phase measurement method. The system comprised a Mach-Zehnder interferometer, along with a high-speed camera capable of up to 20,000 frames-per-second. The sample was placed in the interferometer and irradiated with 100 ns, 2 kHz Q-switched pulses from a high-power Nd:YAG laser operating at 1064 nm. Phase measurements were converted to temperature using known values of thermal expansion and temperature-dependent refractive index for glass. The thermal decay at the center of the thermal wave was fit to a function derived from first principles with excellent agreement. Additionally, the spread of the thermal distribution over time was fit to the same function. Both the temporal decay fit and the spatial fit produced a thermal diffusivity of 5×10-7  m2/s.

  16. Laboratory experiments, high angular-resolution EBSD, and micromechanical modelling reveal residual stresses and their distribution in deformed olivine

    Science.gov (United States)

    Hansen, Lars; Wallis, David; Kempton, Imogen; Lebensohn, Ricardo; Wilkinson, Angus

    2017-04-01

    During high-temperature deformation of rocks, stresses are predicted to be distributed heterogeneously throughout the constituent grains. After unloading, much of this stress is potentially retained in the aggregate as residual stress, a phenomenon that may have large-scale geodynamic implications. After large stress changes in the solid Earth (e.g., glacial unloading or post-seismic relaxation), residual stresses can affect the immediate mechanical response of the rocks. Furthermore, examination of residual stresses in naturally deformed rocks additionally presents an opportunity to learn about ancient deformation events. These residual stresses arise from the anisotropic nature of the mechanical properties of minerals and from the heterogeneous substructures that form within grains (e.g., dislocation arrays and subgrain boundaries). This heterogeneity is therefore related to mechanical interactions on short (e.g., between individual dislocations), intermediate (e.g., between groups of dislocations), and long (e.g., between grains of differing orientation) spatial scales. We examine residual stresses in upper mantle analogues with three different methods. First, stress-dip tests were conducted on olivine single crystals at temperatures greater than 1250°C in a new uniaxial deformation apparatus with a piezoelectric actuator. These experiments reveal that the average residual stresses stored in deformed single crystals can be on the order of 50% of the applied differential stress. However, the magnitude of residual stress is likely a function of crystal orientation during deformation. Second, high angular-resolution electron backscatter diffraction (HR-EBSD) allows the residual stresses in deformed single crystals and polycrystals to be mapped with <1 micron spatial resolution. HR-EBSD mapping reveals stress heterogeneities on the order of differential stresses applied during deformation. Stresses averaged over each map are in reasonable agreement with the outcome

  17. Accuracy analysis of continuous deformation monitoring using BeiDou Navigation Satellite System at middle and high latitudes in China

    Science.gov (United States)

    Jiang, Weiping; Xi, Ruijie; Chen, Hua; Xiao, Yugang

    2017-02-01

    As BeiDou Navigation Satellite System (BDS) has been operational in the whole Asia-Pacific region, it means a new GNSS system with a different satellite orbit structure will become available for deformation monitoring in the future. Conversely, GNSS deformation monitoring data are always processed with a regular interval to form displacement time series for deformation analysis, where the interval can neither be too long from the time perspective nor too short from the precision of determined displacements angle. In this paper, two experimental platforms were designed, with one being at mid-latitude and another at higher latitude in China. BDS data processing software was also developed for investigating the accuracy of continuous deformation monitoring using current in-orbit BDS satellites. Data over 20 days at both platforms were obtained and were processed every 2, 4 and 6 h to generate 3 displacement time series for comparison. The results show that with the current in-orbit BDS satellites, in the mid-latitude area it is easy to achieve accuracy of 1 mm in horizontal component and 2-3 mm in vertical component; the accuracy could be further improved to approximately 1 mm in both horizontal and vertical directions when combined BDS/GPS measurements are employed. At higher latitude, however, the results are not as good as expected due to poor satellite geometry, even the 6 h solutions could only achieve accuracy of 4-6 and 6-10 mm in horizontal and vertical components, respectively, which implies that it may not be applicable to very high-precision deformation monitoring at high latitude using the current BDS. With the integration of BDS and GPS observations, however, in 4-h session, the accuracy can achieve 2 mm in horizontal component and 4 mm in vertical component, which would be an optimal choice for high-accuracy structural deformation monitoring at high latitude.

  18. TRP 9904 - Constitutive Behavior of High Strength Multiphase Sheel Steel Under High Strain Rate Deformation

    Energy Technology Data Exchange (ETDEWEB)

    David Matlock; John Speer

    2005-03-31

    The focus of the research project was to systematically assess the strain rate dependence of strengthening mechanisms in new advanced high strength sheet steels. Data were obtained on specially designed and produced Duel Phase and TRIP steels and compared to the properties of automotive steels currently in use.

  19. Control technology and coordination deformation mechanism of rise entry group with high ground stress

    Institute of Scientific and Technical Information of China (English)

    Li Qingfeng; Zhu Quanqu

    2012-01-01

    Based on engineering practices of Wuyang Coal Mine,we carried out X-ray diffract researches on No.3 coal; and the rocks of its roof and floor by XRD meter,and simulated the interactive effect of the surrounding rock deformation by FLAC2D5.0 numerical simulation software under the condition of different tunneling method of multimine roadway in parallel.The internal structures of the surrounding rocks of 76 belt roadway were monitored by borehole observation instruments; and then,we analyzed the reason of failure and deformation of surrounding rocks of several rise entry,and proposed the technical measures for controlling interactive effect of several rise entry surrounding rock deformation at last.For the thickness seam rise roadway,two conclusions were drawn:one is that the co-deformation among roadway groups mainly reflecton that both shear failure and deformation in coal pillar among roadways have decreased the width of pillar core region and clamping action of coal pillar to roof strata,increased the actual span of roof strata,intensified the flexural failure of roof strata and prized the bed separation of roof deep rock strata.The other conclusion is that the factors controlling the interactive deformation among roadways is obvious when appropriate re-adjustment in construction sequence of the tunneling of multimine parallel roadways because the construction sequence among roadways also has great effects on deformation of the surrounding rock in roadway.

  20. Stress and deformation characteristics of sea ice in a high resolution numerical sea ice model.

    Science.gov (United States)

    Heorton, Harry; Feltham, Daniel; Tsamados, Michel

    2017-04-01

    The drift and deformation of sea ice floating on the polar oceans is due to the applied wind and ocean currents. The deformations of sea ice over ocean basin length scales have observable patterns; cracks and leads in satellite images and within the velocity fields generated from floe tracking. In a climate sea ice model the deformation of sea ice over ocean basin length scales is modelled using a rheology that represents the relationship between stresses and deformation within the sea ice cover. Here we investigate the link between observable deformation characteristics and the underlying internal sea ice stresses and force balance using the Los Alamos numerical sea ice climate model. In order to mimic laboratory experiments on the deformation of small cubes of sea ice we have developed an idealised square domain that tests the model response at spatial resolutions of up to 500m. We use the Elastic Anisotropic Plastic and Elastic Viscous Plastic rheologies, comparing their stability over varying resolutions and time scales. Sea ice within the domain is forced by idealised winds in order to compare the confinement of wind stresses and internal sea ice stresses. We document the characteristic deformation patterns of convergent, divergent and rotating stress states.

  1. Relaxation of a highly deformed elastic filament at a fluid interface

    CERN Document Server

    Prasath, S Ganga; Govindarajan, Rama; Menon, Narayanan

    2016-01-01

    We perform experiments to investigate the relaxation of a highly deformed elastic filament at a liquid-air interface. The dynamics for filaments of differing length, diameter and elastic modulus collapse to a single curve when the time-dependence is scaled by a time scale $\\tau = 8 \\pi \\mu L_o^4/B$. The relaxation, however, is completed in a very small fraction of the time $\\tau$. Even though the time scale $\\tau$ can be obtained by balancing the linear bending and viscous forces, it appears to control the highly nonlinear regime of our experiments. Nonlinear numerical simulations show that the force due to tension along the filament is comparable to the bending force, producing a net elastic restoring force that is much smaller than either term. We perform particle image velocimetry at the liquid-air interface to support the results of the numerics. Finally, we find that when the filament is initialized in asymmetric shapes, it rapidly goes to a shape with symmetric stresses. This symmetrisation process is e...

  2. Accumulative deformation in railway track induced by high-speed traffic loading of the trains

    Institute of Scientific and Technical Information of China (English)

    Bian Xuecheng; Jiang Hongguang; Chen Yunmin

    2010-01-01

    Prediction and control of the permanent settlement of a track caused by traffic loading from trains is crucial to high-speed railway design and maintenance. In this study, a unified prediction model of accumulative deformation of geomaterials used in railway construction subjected to cyclic loadings is introduced and calibrated using physical model testing. Based on this versatile model, a calculation approach to determine the track structure settlement under repeated loadings caused by the movement of the wheel axle of the train is proposed. Regression analysis on the physical model testing is adopted to determine the parameters involved in the computational approach. Comparison of model test data and computed results shows that the parameters obtained from the back-analysis are consistent throughout the various testing conditions, and the proposed calculation approach is capable of satisfactorily predicting the accumulative settlement of the railway roadbed and subgrade soil for various axle loads and loading cycles. A case study of a high-speed railway is performed to demonstrate the feasibility of the proposed approach in realistic engineering applications. The computation results from the settlement development of a roadbed and subgrade soil are presented and discussed.

  3. Deformation Behavior at High Temperature of Feeder Pipe Material in CANDU

    Energy Technology Data Exchange (ETDEWEB)

    Kim, SungSoo; Lee, Yoon Sang; Kim, Young Suk [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    The specification of these nuclear materials is called as a SA106 in pipe shape. The chemical composition of SA106 is same as mild steel. The deformation behavior at high temperature in mild steel is rarely understood yet, although mild steel is a major structural material in commercial nuclear reactors. Thus, the high temperature tensile tests were carried out up to 500℃. The results are properly interpreted in the aspects of the short range order reaction. This paper is concluded as follows. 1. The FC mild steel shows a yield point. at below 400℃, whereas the WQ does not show the yield point. The reason why the yield point appears is due to the destruction of SRO formed during furnace cooling process 2. The serration appears at 50-150℃, at which the exothermic reaction takes place. The origin of the exothermic reaction is a formation of SRO between Fe and C. 3. The shape of serration changes significantly at above 121℃ and becomes downward generally, this is mainly due to both destruction of SRO by the disordering and by the shearing.

  4. Towards a high resolution inventory of anthropogenic deformation in North America using InSAR

    Science.gov (United States)

    Pritchard, M. E.; Lohman, R. B.; Taylor, H.; Semple, A.; Valentino, B.

    2015-12-01

    Anthropogenic surface deformation is important to measure for several reasons -- 1) it could be a hazard to infrastructure; 2) it could contaminate precise measurements of other types of deformation (e.g., magmatic or tectonic); and 3) the deformation can provide otherwise inaccessible information about the subsurface as we measure the Earth's response to known pumping, surface change, or mining activity. While there are studies at individual sites in North America that demonstrate these three types of studies, we lack a continental synoptic view of anthropogenic deformation and its significance. To fill this gap, we use satellite Interferometric Synthetic Aperture Radar (InSAR) data to image ground deformation across the continent with a spatial resolution of 1 km/pixel or better using results from the literature as well as new analysis of more than 5000 interferograms from the ERS, Envisat, and ALOS satellites, which collectively span 1992-2011. Our compilation is not complete in terms of spatially or temporal coverage nor is it uniform in quality over the region -- certainly we have missed some areas of deformation. Most of the data analyzed is in the western US, but ALOS observations east of the Rocky Mountains are of good quality even in vegetated and snowy areas and we document mining subsidence greater than several cm per year in NY, PA, and WV. We catalog more than 200 anthropogenic deformation signals, including about 45 that are not previously reported. The majority of these deformation sources can be attributed to groundwater extraction (66%), 8% to geothermal activity, 13% to hydrocarbon extraction, 11% to mining activity, and 2% to other sources such as lake loading. In a few areas, the source of deformation is not yet determined. As expected, most deformation is time dependent and so continuous monitoring is needed. In some areas, comparisonbetween pumping records and surface deformation reveals some suprises. For example, at the East Mesa Geothermal

  5. Quasi-static tensile deformation and fracture behavior of a highly particle-filled composite using digital image correlation method

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Polymer bonded explosives (PBXs) are highly particle-filled composite materials.This paper experimentally studies the tensile deformation and fracture behavior of a PBX simulation by using the semi-circular bending (SCB) test.The deformation and fracture process of a pre-notched SCB sample with a random speckle pattern is recorded by a charge coupled device camera.The displacement and strain fields on the observed surface during the loading process are obtained by using the digital image correlation method....

  6. Effect of Cooling Start Temperature on Microstructure and Mechanical Properties of X80 High Deformability Pipeline Steel

    Institute of Scientific and Technical Information of China (English)

    ZHENG Xiao-fei; KANG Yong-lin; MENG De-liang; AN Shou-yong; XIA Dian-xiu

    2011-01-01

    The effect of cooling (laminar cooling) start temperature on the phase constitution was analyzed by quanti- tative metallography. The martensite/austenite (M/A) island distribution was fixed by colour metallography. The strength and uniform elongation of the steels were tested with quasi-static tensile testing machine. The in-coordinate deformation of the soft and hard phases was analyzed using FEM. The results indicate that when the cooling start temperature is 690 ℃, the mechanical properties are the best, meeting the requirements of X80 high deformability pipeline steel.

  7. Evolution of microstructural parameters and flow stresses toward limits in nickel deformed to ultra-high strains

    DEFF Research Database (Denmark)

    Zhang, Hongwang; Huang, Xiaoxu; Hansen, Niels

    2008-01-01

    A quantitative analysis of microstructure and strength as a function of strain is presented for polycrystalline nickel (99.5%) deformed by high-pressure torsion in the strain range vertical bar-300 (epsilon(VM), von Mises strain). Typical lamellar structures consisting of extended boundaries...... and short interconnecting boundaries have been found, with additional features at large strains which are equiaxed regions, small equiaxed subgrains and deformation twins. The evolution of microstructure and microstructural parameters falls in stages: (i) the first stage at epsilon(VM) = vertical bar-12...

  8. Mathematical modeling of phenomena of dynamic recrystallization during hot plastic deformation in high-carbon bainitic steel

    Directory of Open Access Journals (Sweden)

    T. Dembiczak

    2017-01-01

    Full Text Available Based on the research results, coefficients were determined in constitutive equations, describing the kinetics of dynamic recrystallization in high-carbon bainitic steel during hot deformation. The developed mathematical model takes into account the dependence of changing kinetics in the size evolution of the initial austenite grains, the value of strain, strain rate, temperature and time. Physical simulations were carried out on rectangular specimens measuring 10 × 15 × 20 mm. Compression tests with a plane state of deformation were carried out using a Gleeble 3800.

  9. Study of a wide-aperture combined deformable mirror for high-power pulsed phosphate glass lasers

    Energy Technology Data Exchange (ETDEWEB)

    Samarkin, V V; Aleksandrov, A G; Romanov, P N; Rukosuev, A L; Kudryashov, A V [Moscow State University of Mechanical Engineering, Moscow (Russian Federation); Jitsuno, T [Institute of Laser Engineering, Osaka University, 2-6 Yamada-oka, Suita, Osaka 565-0871 (Japan)

    2015-12-31

    A deformable mirror with the size of 410 × 468 mm controlled by bimorph piezoceramic plates and multilayer piezo stacks is developed. The response functions of individual actuators and the measurements of the flatness of the deformable mirror surface are presented. The study of mirrors with an interferometer and a wavefront sensor has shown that it is possible to improve the surface flatness down to a residual roughness of 0.033 μm (RMS). The possibility of correction of beam aberrations in an ultra-high-power laser using the created bimorph mirror is demonstrated. (letters)

  10. Microplastic deformation of TiB/sub 2/ particles during vibrocrushing and pressing in high pressure chambers

    Energy Technology Data Exchange (ETDEWEB)

    Ordan' yan, S.S.; Kravchik, A.E.; Ponomarenko, V.A.; Chunov, V.D. (Leningradskij Tekhnologicheskij Inst. (USSR))

    1984-04-01

    The character of plastic strain in titanium diboride particles is described. It is shown that during titanium diboride vibrocrushing unlike that of carbide there is practically no microplastic deformation that is observed only when TiB/sub 2/ particles are squeezed in high-pressure chambers at pressures not less than 3GPa.

  11. The mechanical properties and the deformation microstructures of the C15 Laves phase Cr2Nb at high temperatures

    NARCIS (Netherlands)

    Kazantzis, A. V.; Aindow, M.; Jones, I. P.; Triantafyllidis, G. K.; De Hosson, J. Th. M.

    Compression tests between 1250 and 1550 degrees C and 10(-5) and 5 x 10(-3) s(-1) and transmission electron microscopy have been employed to investigate the high temperature mechanical properties and the deformation mechanisms of the C15 Cr2Nb Laves phase. The stress-peaks in the compression curves

  12. Micro- and submicrostructural evidence for high-temperature brittle-ductile transition deformation of hornblende: Case study of high-grade mylonites from Diancangshan, western Yunnan

    Institute of Scientific and Technical Information of China (English)

    CAO; ShuYun; LIU; JunLai; HU; Ling

    2007-01-01

    OM (optical microscope)/TEM (transmission electron microscope) micro- and submicrostructural analysis of hornblende rocks sheared at high temperatures from the Diancangshan area, western Yunnan reveals evidence for deformation in the brittle-ductile transition of hornblende at middle crustal level (about 637℃ and 0.653 GPa) and mechanisms of deformation in the transitional regime are further discussed. Sheared hornblende rocks at middle crustal level have typical mylonitic microstructures, shown by coarse porphyroclasts and fine matrix grains. Different mineral phases in the rocks show distinct deformation characteristics. Hornblende and feldspar grains are intensely deformed with obvious grainsize reduction, but quartz grains are recrystallized dominantly by grain growth. Hornblende grains show typical brittle-ductile transition nature. Initial crystallographic orientations of porphyroclasts have strong effects on the behavior of grains during deformation. There are mainly two types of porphyroclasts, type I "hard" porphyroclasts and type II "soft" porphyroclasts, with [001] perpendicular and parallel to external shear stresses respectively. "Hard" porphyroclasts generally occur as competent grains that are rarely deformed or sometimes deformed by fracturing and dislocation tangling. "Soft" porphyroclasts are highly deformed primarily by dislocation tangling (as shown in the cores of the porphyroclasts), but twinning, dislocation glide and climb probably due to hydrolytic weakening also contribute to dynamic recrystallization of the porphyroclasts into fine grains in the matrix. The micro- and submicrostructures of the two types of porphyroclasts and fine-grained matrix provide powerful evidence for the behavior of brittle-ductile transition of hornblende grains. It is concluded that twinning nucleation is one of the most important processes that operate during dynamic recrystallization of hornblende crystals at the brittle-ductile transition. (100) [001] twin

  13. Microstructural evolution and mechanical properties of high strength magneisum alloys fabricated by deformation processing

    Science.gov (United States)

    Mansoor, Bilal

    The goal of this research was to develop high strength Mg by thermo-mechanical processing. Several novel techniques were developed to impart large plastic strains on Mg alloys and Mg based composites. The main emphasis of this work was on investigating the effect of different processing schemes on grain-refinement and texture modification of processed material. The room-temperature and elevated-temperature mechanical behavior of processed-Mg was studied in detail. Biaxial corrugated pressing, also known as alternate biaxial reverse corrugation processing was applied to twin-roll cast AZ31 Mg and warm-extruded ZK60 Mg. Friction stir processing to partial depths was applied to thixomolded AM60 Mg and warm-extruded ZK60 Mg. A new process called "bending reverse-bending", was developed and applied to hot rolled AZ31-H24 Mg. A Mg/Al laminated composite was developed by hot pressing and rolling. In processed condition, Mg alloys exhibit enhancement in room-temperature strength and ductility, as well as elevated temperature formability. It was concluded that improvement in mechanical properties of processed-Mg is strongly influenced by grain size and precipitates; while ductility largely depends on resulting deformation textures.

  14. High-temperature deformation of dispersion-strengthened Cu-Zr-Ti-C alloys

    Energy Technology Data Exchange (ETDEWEB)

    Palma, Rodrigo H. [Departamento de Ingenieria Mecanica, Universidad de Chile, Beauchef 850, 4 deg. Piso, Santiago 6511261 (Chile)]. E-mail: rhpalma@ing.uchile.ct; Sepulveda, Aquiles [Departamento de Ingenieria Mecanica, Universidad de Chile, Beauchef 850, 4 deg. Piso, Santiago 6511261 (Chile); Espinoza, Rodrigo [Departamento de Ingenieria Mecanica, Universidad de Chile, Beauchef 850, 4 deg. Piso, Santiago 6511261 (Chile); Dianez, M. Jesus [Instituto de Ciencia de Materiales de Sevilla, Americo Vespucio s/n, Isla de La Cartuja, Sevilla (Spain); Criado, Jose M. [Instituto de Ciencia de Materiales de Sevilla, Americo Vespucio s/n, Isla de La Cartuja, Sevilla (Spain); Sayagues, M. Jesus [Instituto de Ciencia de Materiales de Sevilla, Americo Vespucio s/n, Isla de La Cartuja, Sevilla (Spain)

    2005-01-25

    The hot mechanical behaviour and microstructure of Cu-5 vol.% TiC, Cu-5 vol.% ZrO{sub 2} and Cu-2.5 vol.% TiC-2.5 vol.% ZrO{sub 2} alloys prepared by reaction milling were studied. After a test of 1 h annealing at 1173 K, the Cu-5 vol.% ZrO{sub 2} alloy presented the lower softening resistance to annealing, while the other two ones kept their initial room-temperature hardness (about 2 GPa). Hot-compression tests at 773 and 1123 K, at initial true strain rates of 0.85 x 10{sup -3} and 0.85 x 10{sup -4} s{sup -1} were performed. The Cu-2.5 vol.% TiC-2.5 vol.% ZrO{sub 2} and the Cu-5 vol.% ZrO{sub 2} alloys were the strongest and softest materials, respectively. Moreover, by electron microscopy, nanometric TiC and micrometric particles were detected in the Cu-5 vol.% TiC and Cu-5 vol.% ZrO{sub 2} alloys, respectively. A possible explanation for the observed behaviour of these materials is proposed. In the compression tests, it was also found that strain rate has a low effect on flow stress, as it has been previously observed by various authors in dispersion-strengthened alloys deformed at high temperatures.

  15. OBSERVATIONS ON DEFORMATION BEHAVIOR OF HIGH PERFORMANCE FIBERS BY POLARIZING OPTICAL MICROSCOPY

    Institute of Scientific and Technical Information of China (English)

    Chang-fa Xiao; Yu-feng Zhang

    2000-01-01

    By means of polarizing optical microscopy (POM), deformation behavior of four kinds of fibers, i.e. ultra high molecular weight polyethylene (UHMW-PE) fiber, polyvinyl alcohol (PVA) fiber, polyethylene terephthalate (PET) fiber,and wholly aromatic (p-hydroxybenzoic acid/2-hydroxy-6-naphthoic acid) copolyester [P(HBA/HNA)]/PET (ACPET blend) fiber, in axial compression, axial impacting, and bending was observed. In compression, kink bands formed at an angle of 55~60° to the fiber axis in 10-times-drawn UHMW-PE fiber, 75~80° in 40-times-drawn sample, 80° in PVA fiber, and 90°in the ACPET blend fiber. In impacting and bending, band angles of UHMW-PE, PVA and PET fibers are nearly the same as those formed in compression, indicating that slip systems do not change. For any of the four kinds of fiber, band spacing exhibits great differences in compression, in impacting, and in bending, which may be attributed to the differences in the degrees of strain or stress concentration.

  16. Influence of high temperature pre-deformation on the dissolution rate of delta ferrites in martensitic heat-resistant steels

    Science.gov (United States)

    Li, Junru; Liu, Jianjun; Jiang, Bo; Zhang, Chaolei; Liu, Yazheng

    2017-03-01

    The dissolution process of delta ferrites and the influence of high temperature pre-deformation on the dissolution rate of delta ferrites in martensitic heat-resistant steel 10Cr12Ni3Mo2VN were studied by isothermal heating and thermal simulation experiments. The precipitation temperature of delta ferrites in experimental steel is about 1195 °C. M23C6-type carbides incline to precipitate and coarsen at the boundaries of delta ferrites below 930 °C, and can be rapidly dissolved by heating at 1180 °C. The percentage of delta ferrites gradually decreases with heating time. And a Kolmogorov-Johnson-Mehl-Avrami equation was established to describe the dissolution process of delta ferrites at 1180 °C. High temperature pre-deformation can markedly increase the dissolution rate of delta ferrites. Pre-deformation can largely increase the interface area between delta ferrite and matrix and thus increase the unit-time diffusing quantities of alloying elements between delta ferrites and matrix. In addition, high temperature pre-deformation leads to dynamic recrystallization and increases the number of internal grain boundaries in the delta ferrites. This can also greatly increase the diffusing rate of alloying elements. In these cases, the dissolution of delta ferrites can be promoted.

  17. High-strain-induced deformation mechanisms in block-graft and multigraft copolymers

    KAUST Repository

    Schlegel, Ralf

    2011-12-13

    The molecular orientation behavior and structural changes of morphology at high strains for multigraft and block-graft copolymers based on polystyrene (PS) and polyisoprene (PI) were investigated during uniaxial monotonic loading via FT-IR and synchrotron SAXS. Results from FT-IR revealed specific orientations of PS and PI segments depending on molecular architecture and on the morphology, while structural investigations revealed a typical decrease in long-range order with increasing strain. This decrease was interpreted as strain-induced dissolution of the glassy blocks in the soft matrix, which is assumed to affect an additional enthalpic contribution (strain-induced mixing of polymer chains) and stronger retracting forces of the network chains during elongation. Our interpretation is supported by FT-IR measurements showing similar orientation of rubbery and glassy segments up to high strains. It also points to highly deformable PS domains. By synchrotron SAXS, we observed in the neo-Hookean region an approach of glassy domains, while at higher elongations the intensity of the primary reflection peak was significantly decreasing. The latter clearly verifies the assumption that the glassy chains are pulled out from the domains and are partly mixed in the PI matrix. Results obtained by applying models of rubber elasticity to stress-strain and hysteresis data revealed similar correlations between the softening behavior and molecular and morphological parameters. Further, an influence of the network modality was observed (random grafted branches). For sphere forming multigraft copolymers the domain functionality was found to be less important to achieve improved mechanical properties but rather size and distribution of the domains. © 2011 American Chemical Society.

  18. On the deformation mechanisms and electrical behavior of highly stretchable metallic interconnects on elastomer substrates

    Science.gov (United States)

    Arafat, Yeasir; Dutta, Indranath; Panat, Rahul

    2016-09-01

    Flexible metallic interconnects are highly important in the emerging field of deformable/wearable electronics. In our previous work [Arafat et al., Appl. Phys. Lett. 107, 081906 (2015)], interconnect films of Indium metal, periodically bonded to an elastomer substrate using a thin discontinuous/cracked adhesion interlayer of Cr, were shown to sustain a linear strain of 80%-100% without failure during repeated cycling. In this paper, we investigate the mechanisms that allow such films to be stretched to a large strain without rupture along with strategies to prevent a deterioration in their electrical performance under high linear strain. Scanning Electron Microscopy and Digital Image Correlation are used to map the strain field of the Cr adhesion interlayer and the In interconnect film when the elastomer substrate is stretched. It is shown that the Cr interlayer morphology, consisting of islands separated by bi-axial cracks, accommodates the strain primarily by widening of the cracks between the islands along the tensile direction. This behavior is shown to cause the strain in the In interconnect film to be discontinuous and concentrated in bands perpendicular to the loading direction. This localization of strain at numerous periodically spaced locations preempts strain-localization at one location and makes the In film highly stretchable by delaying rupture. Finally, the elastic-plastic mismatch-driven wrinkling of the In interconnect upon release from first loading cycle is utilized to delay the onset of plasticity and allow the interconnect to be stretched repeatedly up to 25% linear strain in subsequent cycles without a deterioration of its electrical performance.

  19. Experimental Validation of Two-dimensional Finite Element Method for Simulating Constitutive Response of Polycrystals During High Temperature Plastic Deformation

    Science.gov (United States)

    Agarwal, Sumit; Briant, Clyde L.; Krajewski, Paul E.; Bower, Allan F.; Taleff, Eric M.

    2007-04-01

    A finite element method was recently designed to model the mechanisms that cause superplastic deformation (A.F. Bower and E. Wininger, A Two-Dimensional Finite Element Method for Simulating the Constitutive Response and Microstructure of Polycrystals during High-Temperature Plastic Deformation, J. Mech. Phys. Solids, 2004, 52, p 1289-1317). The computations idealize the solid as a collection of two-dimensional grains, separated by sharp grain boundaries. The grains may deform plastically by thermally activated dislocation motion, which is modeled using a conventional crystal plasticity law. The solid may also deform by sliding on the grain boundaries, or by stress-driven diffusion of atoms along grain boundaries. The governing equations are solved using a finite element method, which includes a front-tracking procedure to monitor the evolution of the grain boundaries and surfaces in the solid. The goal of this article is to validate these computations by systematically comparing numerical predictions to experimental measurements of the elevated-temperature response of aluminum alloy AA5083 (M.-A. Kulas, W.P. Green, E.M. Taleff, P.E. Krajewski, and T.R. McNelley, Deformation Mechanisms in Superplastic AA5083 materials. Metall. Mater. Trans. A, 2005, 36(5), p 1249-1261). The experimental work revealed that a transition occurs from grain-boundary sliding to dislocation (solute-drag) creep at approximately 0.001/s for temperatures between 425 and 500 °C. In addition, increasing the grain size from 7 to 10 μm decreased the transition to significantly lower strain rates. Predictions from the finite element method accurately predict the effect of grain size on the transition in deformation mechanisms.

  20. Microstructure and nanohardness distribution in a polycrystalline Zn deformed by high strain rate impact

    Energy Technology Data Exchange (ETDEWEB)

    Dirras, G., E-mail: dirras@univ-paris13.fr [LSPM, CNRS, UPR 3407, Universite Paris 13, 99 avenue Jean Baptiste Clement, 93430 Villetaeuse (France); Ouarem, A. [LSPM, CNRS, UPR 3407, Universite Paris 13, 99 avenue Jean Baptiste Clement, 93430 Villetaeuse (France); Couque, H. [Nexter-Munitions, 7 route de Guerry, 18023 Bourges Cedex (France); Gubicza, J.; Szommer, P. [Department of Materials Physics, Eoetvoes Lorand University, Budapest, P.O.B. 32, H-1518 (Hungary); Brinza, O. [LSPM, CNRS, UPR 3407, Universite Paris 13, 99 avenue Jean Baptiste Clement, 93430 Villetaeuse (France)

    2011-05-15

    Polycrystalline Zn with an average grain size of about 300 {mu}m was deformed by direct impact Hopkinson pressure bar at a velocity of 29 m/s. An inhomogeneous grain structure was found consisting of a center region having large average grain size of 20 {mu}m surrounded by a fine-grained rim with an average grain size of 6 {mu}m. Transmission electron microscopy investigations showed a significant dislocation density in the large-grained area while in the fine-grained rim the dislocation density was negligible. Most probably, the higher strain yielded recrystallization in the outer ring while in the center only recovery occurred. The hardening effect of dislocations overwhelms the smaller grain size strengthening in the center part resulting in higher nanohardness in this region than in the outer ring. - Graphical Abstract: (a): EBSD micrograph showing the initial microstructure of polycrystalline Zn that was subsequently submitted to high strain rate impact. (b): an inhomogeneous grain size refinement was obtained which consists of a central coarse-grained area, surrounded by a fine-grained recrystallized rim. The black arrow points to the disc center. Research Highlights: {yields} A polycrystalline Zn specimen was submitted to high strain rate impact loading. {yields} Inhomogeneous grain refinement occurred due to strain gradient in impacted sample. {yields} A fine-grained recrystallized rim surrounded the coarse-grained center of specimen. {yields} The coarse-grained center exhibited higher hardness than the fine-grained rim. {yields} The higher hardness of the center was caused by the higher dislocation density.

  1. High-resolution microdiffraction study of notch-tip deformation in Mo single crystals using x-ray synchrotron radiation

    Energy Technology Data Exchange (ETDEWEB)

    Ice, G.; Habenschuss, A. (Oak Ridge National Lab., TN (United States)); Bilello, J.C. (California State Univ., Fullerton, CA (United States)); Rebonato, R. (Oxford Univ. (United Kingdom). Physical Chemistry Lab.)

    1989-01-01

    A new technique is presented for the determination of strain fields in single crystals, based on the simultaneous recording of the energy and position of a diffracted beam, with a resolution of 25 micrometers under current experimental conditions. The technique can be profitably used for perfect to highly deformed crystals, in materials as highly absorbing as Molybdenum, and allows a spatial resolution of one part in 10{sup 4}. Indications are given as to possible refinements and improvements of the method.

  2. High-resolution microdiffraction study of notch-tip deformation in Mo single crystals using x-ray synchrotron radiation

    Energy Technology Data Exchange (ETDEWEB)

    Ice, G.; Habenschuss, A. [Oak Ridge National Lab., TN (United States); Bilello, J.C. [California State Univ., Fullerton, CA (United States); Rebonato, R. [Oxford Univ. (United Kingdom). Physical Chemistry Lab.

    1989-12-31

    A new technique is presented for the determination of strain fields in single crystals, based on the simultaneous recording of the energy and position of a diffracted beam, with a resolution of 25 micrometers under current experimental conditions. The technique can be profitably used for perfect to highly deformed crystals, in materials as highly absorbing as Molybdenum, and allows a spatial resolution of one part in 10{sup 4}. Indications are given as to possible refinements and improvements of the method.

  3. Mixed brittle-plastic deformation behaviour in a slate belt. Examples from the High-Ardenne slate belt (Belgium, Germany)

    Science.gov (United States)

    Sintubin, Manuel; van Baelen, Hervé; van Noten, Koen; Muchez, Philippe

    2010-05-01

    In the High-Ardenne slate belt, part of the Rhenohercynian external fold-and-thrust belt at the northern extremity of the Late Palaeozoic Variscan orogen (Belgium, Germany, France), particular quartz vein occurrences can be observed in predominantly fine-grained siliciclastic metasediments. Detailed structural, petrographical and geochemical studies has revealed that these vein occurrences can be related to a mixed brittle-plastic deformation behaviour in a low-grade metamorphic mid-crustal environment. The first type of quartz veins are bedding-perpendicular, lens-shaped extension veins that are confined to the sandstone layers within the multilayer sequence. Fluid inclusion studies demonstrate high fluid pressures suggesting that the individual sandstone bodies acted as isolated high-pressure compartments in an overpressured basin. Hydraulic fracturing occurred during the tectonic inversion (from extension to compression) in the earliest stages of the Variscan orogeny. The vein fill shows a blocky character indicating crystal growth in open cavities. Both the typical lens shape of the veins and the subsequent cuspate-lobate folding of the bed interfaces in between the quartz veins suggest plastic deformation of cohesionless fluid-filled fissures. Metamorphic grade of the host rock and fluid temperature and pressure clearly indicates mid-crustal conditions below the brittle-plastic transition. This first type of quartz veins exemplifies mixed brittle-plastic deformation behaviour, possibly related to a transient deepening of the brittle-plastic transition. This is in contrast with contemporaneous bedding-perpendicular crack-seal veins observed in higher - upper-crustal - structural levels in the slate belt, reflecting pure brittle deformation behaviour. The second type are discordant quartz veins confined to extensional low-angle detachment shear zones. These very irregular veins transect a pre-existing pervasive cleavage fabric. They show no matching walls and

  4. The FEM Simulation Of Cementite Lamellas Deformation In Pearlitic Colony During Drawing Of High Carbon Steel

    Science.gov (United States)

    Milenin, Andriy; Muskalski, Z.

    2007-05-01

    In paper the wire drawing processes was investigated in two levels — steady-state solve using the 2-dimensional rigid-plastic finite element method (macro-level) and modeling of a microstructure change (micro-level). In macro level the joint deformation-temperature problem was considered. In micro-level the process of deformation of representative volume element — RVE was considered. The pearlitic colony deformation and orientation of cementite lamellas change in RVE was modeled with help of a FEM. The micro-level model to rigid-plastic finite element code was implemented. The experimental data of microstructure and orientation of cementite lamellas change was compared with results of a simulations. The influence of multi-pass drawing parameters (as friction, drawing schedule) on orientation of cementite lamellas was investigated.

  5. High-resolution adaptive optics scanning laser ophthalmoscope with multiple deformable mirrors

    Science.gov (United States)

    Chen, Diana C.; Olivier, Scot S.; Jones; Steven M.

    2010-02-23

    An adaptive optics scanning laser ophthalmoscopes is introduced to produce non-invasive views of the human retina. The use of dual deformable mirrors improved the dynamic range for correction of the wavefront aberrations compared with the use of the MEMS mirror alone, and improved the quality of the wavefront correction compared with the use of the bimorph mirror alone. The large-stroke bimorph deformable mirror improved the capability for axial sectioning with the confocal imaging system by providing an easier way to move the focus axially through different layers of the retina.

  6. A comparison of Lagrangian/Eulerian approaches for tracking the kinematics of high deformation solid motion.

    Energy Technology Data Exchange (ETDEWEB)

    Ames, Thomas L.; Farnsworth, Grant V.; Ketcheson, David Isaac; Robinson, Allen Conrad

    2009-09-01

    The modeling of solids is most naturally placed within a Lagrangian framework because it requires constitutive models which depend on knowledge of the original material orientations and subsequent deformations. Detailed kinematic information is needed to ensure material frame indifference which is captured through the deformation gradient F. Such information can be tracked easily in a Lagrangian code. Unfortunately, not all problems can be easily modeled using Lagrangian concepts due to severe distortions in the underlying motion. Either a Lagrangian/Eulerian or a pure Eulerian modeling framework must be introduced. We discuss and contrast several Lagrangian/Eulerian approaches for keeping track of the details of material kinematics.

  7. The effect of heat developed during high strain rate deformation on the constitutive modeling of amorphous polymers

    Science.gov (United States)

    Safari, Keivan H.; Zamani, Jamal; Guedes, Rui M.; Ferreira, Fernando J.

    2016-02-01

    An adiabatic constitutive model is proposed for large strain deformation of polycarbonate (PC) at high strain rates. When the strain rate is sufficiently high such that the heat generated does not have time to transfer to the surroundings, temperature of material rises. The high strain rate deformation behavior of polymers is significantly affected by temperature-dependent constants and thermal softening. Based on the isothermal model which first was introduced by Mulliken and Boyce et al. (Int. J. Solids Struct. 43:1331-1356, 2006), an adiabatic model is proposed to predict the yield and post-yield behavior of glassy polymers at high strain rates. When calculating the heat generated and the temperature changes during the step by step simulation of the deformation, temperature-dependent elastic constants are incorporated to the constitutive equations. Moreover, better prediction of softening phenomena is achieved by the new definition for softening parameters of the proposed model. The constitutive model has been implemented numerically into a commercial finite element code through a user material subroutine (VUMAT). The experimental results, obtained using a split Hopkinson pressure bar, are supported by dynamic mechanical thermal analysis (DMTA) and Decompose/Shift/Reconstruct (DSR) method. Comparison of adiabatic model predictions with experimental data demonstrates the ability of the model to capture the characteristic features of stress-strain curve of the material at very high strain rates.

  8. On the intergranular fracture behavior of high-temperature plastic deformation of 1420 Al-Li alloy

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The tensile deformation hot simulation test of as-cast 1420 Al-Li alloy was performed on Gleeble-1500 Thermal Simulator in the deformation temperature range from 350 to 450 ℃, and the strain rate range from 0.01 to 10.0 s-1.The tensile fracture behavior of the 1420 Al-Li alloy at high temperature was studied experimently. The results show that the tensile fracture mode of the 1420 Al-Li alloy at high temperature is changed from typical transgranular ductile fracture to intergranular brittle fracture with the increase of the deformation temperature and the strain rate. It is made out that the precipitation of LiH is the fundamental reason for the intergranular brittle fracture of the 1420 Al-Li alloy at high temperature. The mechanism of hydrogen embrittlement of the 1420 Al-Li alloy at high temperature was discussed, and it was proposed that the hydrogen embrittlement at high temperature is an integrated function of the dynamic and the static force, which enrichs the theories of hydrogen embrittlement.

  9. Large-strain time-temperature equivalence in high density polyethylene for prediction of extreme deformation and damage

    Directory of Open Access Journals (Sweden)

    Gray G.T.

    2012-08-01

    Full Text Available Time-temperature equivalence is a widely recognized property of many time-dependent material systems, where there is a clear predictive link relating the deformation response at a nominal temperature and a high strain-rate to an equivalent response at a depressed temperature and nominal strain-rate. It has been found that high-density polyethylene (HDPE obeys a linear empirical formulation relating test temperature and strain-rate. This observation was extended to continuous stress-strain curves, such that material response measured in a load frame at large strains and low strain-rates (at depressed temperatures could be translated into a temperature-dependent response at high strain-rates and validated against Taylor impact results. Time-temperature equivalence was used in conjuction with jump-rate compression tests to investigate isothermal response at high strain-rate while exluding adiabatic heating. The validated constitutive response was then applied to the analysis of Dynamic-Tensile-Extrusion of HDPE, a tensile analog to Taylor impact developed at LANL. The Dyn-Ten-Ext test results and FEA found that HDPE deformed smoothly after exiting the die, and after substantial drawing appeared to undergo a pressure-dependent shear damage mechanism at intermediate velocities, while it fragmented at high velocities. Dynamic-Tensile-Extrusion, properly coupled with a validated constitutive model, can successfully probe extreme tensile deformation and damage of polymers.

  10. Scaling properties of Arctic sea ice deformation in high-resolution viscous-plastic sea ice models and satellite observations

    Science.gov (United States)

    Hutter, Nils; Losch, Martin; Menemenlis, Dimitris

    2017-04-01

    Sea ice models with the traditional viscous-plastic (VP) rheology and very high grid resolution can resolve leads and deformation rates that are localised along Linear Kinematic Features (LKF). In a 1-km pan-Arctic sea ice-ocean simulation, the small scale sea-ice deformations in the Central Arctic are evaluated with a scaling analysis in relation to satellite observations of the Envisat Geophysical Processor System (EGPS). A new coupled scaling analysis for data on Eulerian grids determines the spatial and the temporal scaling as well as the coupling between temporal and spatial scales. The spatial scaling of the modelled sea ice deformation implies multi-fractality. The spatial scaling is also coupled to temporal scales and varies realistically by region and season. The agreement of the spatial scaling and its coupling to temporal scales with satellite observations and models with the modern elasto-brittle rheology challenges previous results with VP models at coarse resolution where no such scaling was found. The temporal scaling analysis, however, shows that the VP model does not fully resolve the intermittency of sea ice deformation that is observed in satellite data.

  11. {gamma}-spectroscopy and radioactive beams: search for highly deformed exotic nuclei; Detection {gamma} et faisceaux radioactifs: recherche de noyaux exotiques tres deformes

    Energy Technology Data Exchange (ETDEWEB)

    Rosse, B

    2006-07-15

    This work is devoted to the search for highly deformed nuclei under extreme conditions of isospin, located near the proton drip-line, around A {approx} 130. The experiment was performed at GANIL (Caen) with the SPIRAL radioactive beam facility. The nuclei of interest were produced by fusion-evaporation reactions induced by the neutron deficient Kr{sup 76} radioactive beam (T1/2 = 14.8 h). {gamma}-rays were detected by the EXOGAM array, composed of 11 segmented germanium clover detectors, for which a new segment calibration method has been developed. To extract fusion-evaporation events of a overwhelming background due to the radioactivity of the beam, the EXOGAM array was coupled with the light charged particle detector DIAMANT and the high acceptance VAMOS spectrometer. The latter was used for the first time to detect fusion-evaporation residues. The detailed data analysis allowed us to demonstrate that the EXOGAM + DIAMANT + VAMOS coupling is operational and essential to investigate the structure of these nuclei. Furthermore, the first {gamma} transition was observed in the very exotic odd-odd Pm{sup 130} nucleus. The results have been interpreted with static and dynamic self-consistent microscopic calculations in collaboration with the Theoretical Physicists of the IPN Lyon. (author)

  12. Transient deformational properties of high temperature alloys used in solid oxide fuel cell stacks

    DEFF Research Database (Denmark)

    Tadesse Molla, Tesfaye; Kwok, Kawai; Frandsen, Henrik Lund

    2017-01-01

    Stresses and probability of failure during operation of solid oxide fuel cells (SOFCs) is affected by the deformational properties of the different components of the SOFC stack. Though the overall stress relaxes with time during steady state operation, large stresses would normally appear through...

  13. High temperature deformation behavior and processing map for a nickel-titanium shape memory alloy

    Science.gov (United States)

    Yin, Xiang-Qian; Lee, Sang-Won; Li, Yan-Feng; Park, Chan-Hee; Mi, Xu-Jun; Yeom, Jong-Taek

    2017-09-01

    The hot deformation behavior of 49.2Ti-50.8Ni shape memory alloy was studied using hot compressive deformation testing in the temperature range of 1023-1323 K and at strain rates of 0.01-10 s-1. The work-hardening rate was induced to analyze the stress-strain curves, and the critical stress σc and the dynamic recovery saturation stress σsat were measured which can be specified approximately by the expressions: σsat-1.12σp and σc-0.86σp. An Arrhenius model was calculated to describe the relationship between peak stress and the Z parameter. The relationship between deformation activation energy, the deformation conditions and the effect of Ni component in a binary TiNi alloy on the activation energy were discussed in this work. With the help of electron backscattering diffraction, a connected mode dynamic recrystallization microstructure was confirmed in peak efficiency regimes (850 °C & 0.01 s-1 and 1050 °C & 10 s-1) of the processing map.

  14. a Method for the Extraction of Long-Term Deformation Characteristics of Long-Span High-Speed Railway Bridges Using High-Resolution SAR Images

    Science.gov (United States)

    Jia, H. G.; Liu, L. Y.

    2016-06-01

    Natural causes and high-speed train load will result in the structural deformation of long-span bridges, which greatly influence the safety operation of high-speed railway. Hence it is necessary to conduct the deformation monitoring and regular status assessment for long-span bridges. However for some traditional surveying technique, e.g. control-point-based surveying techniques, a lot of human and material resources are needed to perform the long-term monitoring for the whole bridge. In this study we detected the long-term bridge deformation time-series by persistent scatterer interferometric synthetic aperture radar (PSInSAR) technique using the high-resolution SAR images and external digital elevation model. A test area in Nanjing city in China is chosen and TerraSAR-X images and Tandem-X for this area have been used. There is the Dashengguan bridge in high speed railway in this area as study object to evaluate this method. Experiment results indicate that the proposed method can effectively extract the long-term deformation of long-span high-speed railway bridge with higher accuracy.

  15. A METHOD FOR THE EXTRACTION OF LONG-TERM DEFORMATION CHARACTERISTICS OF LONG-SPAN HIGH-SPEED RAILWAY BRIDGES USING HIGH-RESOLUTION SAR IMAGES

    Directory of Open Access Journals (Sweden)

    H. G. Jia

    2016-06-01

    Full Text Available Natural causes and high-speed train load will result in the structural deformation of long-span bridges, which greatly influence the safety operation of high-speed railway. Hence it is necessary to conduct the deformation monitoring and regular status assessment for long-span bridges. However for some traditional surveying technique, e.g. control-point-based surveying techniques, a lot of human and material resources are needed to perform the long-term monitoring for the whole bridge. In this study we detected the long-term bridge deformation time-series by persistent scatterer interferometric synthetic aperture radar (PSInSAR technique using the high-resolution SAR images and external digital elevation model. A test area in Nanjing city in China is chosen and TerraSAR-X images and Tandem-X for this area have been used. There is the Dashengguan bridge in high speed railway in this area as study object to evaluate this method. Experiment results indicate that the proposed method can effectively extract the long-term deformation of long-span high-speed railway bridge with higher accuracy.

  16. High performance computing for deformable image registration: towards a new paradigm in adaptive radiotherapy.

    Science.gov (United States)

    Samant, Sanjiv S; Xia, Junyi; Muyan-Ozcelik, Pinar; Owens, John D

    2008-08-01

    The advent of readily available temporal imaging or time series volumetric (4D) imaging has become an indispensable component of treatment planning and adaptive radiotherapy (ART) at many radiotherapy centers. Deformable image registration (DIR) is also used in other areas of medical imaging, including motion corrected image reconstruction. Due to long computation time, clinical applications of DIR in radiation therapy and elsewhere have been limited and consequently relegated to offline analysis. With the recent advances in hardware and software, graphics processing unit (GPU) based computing is an emerging technology for general purpose computation, including DIR, and is suitable for highly parallelized computing. However, traditional general purpose computation on the GPU is limited because the constraints of the available programming platforms. As well, compared to CPU programming, the GPU currently has reduced dedicated processor memory, which can limit the useful working data set for parallelized processing. We present an implementation of the demons algorithm using the NVIDIA 8800 GTX GPU and the new CUDA programming language. The GPU performance will be compared with single threading and multithreading CPU implementations on an Intel dual core 2.4 GHz CPU using the C programming language. CUDA provides a C-like language programming interface, and allows for direct access to the highly parallel compute units in the GPU. Comparisons for volumetric clinical lung images acquired using 4DCT were carried out. Computation time for 100 iterations in the range of 1.8-13.5 s was observed for the GPU with image size ranging from 2.0 x 10(6) to 14.2 x 10(6) pixels. The GPU registration was 55-61 times faster than the CPU for the single threading implementation, and 34-39 times faster for the multithreading implementation. For CPU based computing, the computational time generally has a linear dependence on image size for medical imaging data. Computational efficiency is

  17. Effect of different stages of tensile deformation on micromagnetic parameters in high-strength, low-alloy steel

    Energy Technology Data Exchange (ETDEWEB)

    Vaidyanathan, S.; Moorthy, V.; Kalyanasundaram, P.; Jayakumar, T.; Raj, B. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Metallurgy and Materials Group

    1999-08-01

    The influence of tensile deformation on the magnetic Barkhausen emissions (MBE) and hysteresis loop has been studied in a high-strength, low-alloy steel (HSLA) and its weldment. The magnetic measurements were made both in loaded and unloaded conditions for different stress levels. The root-mean-square (RMS) voltage of the MBE has been used for analysis. This study shows that the preyield and postyield deformation can be identified from the change in the MBE profile. The initial elastic deformation showed a linear increase in the MBE level in the loaded condition, and the MBE level remained constant in the unloaded condition. The microplastic yielding, well below the macroyield stress, significantly reduces the MBE, indicating the operation of grain-boundary dislocation sources below the macroyield stress. This is indicated by the slow increase in the MBE level in the loaded condition and the decrease in the MBE level in the unloaded condition. The macroyielding resulted in a significant increase in the MBE level in the loaded condition and, more clearly, in the unloaded condition. The increase in the MBE level during macroyielding has been attributed to the grain rotation phenomenon, in order to maintain the boundary integrity between adjacent grains, which would preferentially align the magnetic domains along the stress direction. This study shows that MBE during tensile deformation can be classified into four stages: (1) perfectly elastic, (2) microplastic yielding, (3) macroyielding, and (4) progressive plastic deformation. A multimagnetic parameter approach, combining the hysteresis loop and MBE, has been suggested to evaluate the residual stresses.

  18. Characterization of basal-prismatic interface of ? twin in deformed titanium by high-resolution transmission electron microscopy

    Science.gov (United States)

    Sun, Q.; Zhang, X. Y.; Tu, J.; Ren, Y.; Qin, H.; Liu, Q.

    2015-03-01

    Disconnections in the basal-prismatic (BP) interfaces of ? twin have been investigated by many computer simulations. In this paper, we report experimentally that the disconnection in the BP interface of ? twin in deformed titanium can be observed by high-resolution TEM (HRTEM). This disconnection can be characterized as ? using a coherent dichromatic complex. Correspondingly, the migration process of the basal-prismatic plane resulting from ? glide is described.

  19. Discovery of a new isomeric state in $^{68}$Ni: Evidence for a highly-deformed proton intruder state

    CERN Document Server

    Dijon, A; De France, G; De Angelis, G; Duchêne, G; Dudouet, J; Franchoo, S; Gadea, A; Gottardo, A; Hüyük, T; Jacquot, B; Kusoglu, A; Lebhertz, D; Lehaut, G; Martini, M; Napoli, D R; Nowacki, F; Péru, S; Poves, A; Recchia, F; Redon, N; Sahin, E; Schmitt, C; Sferrazza, M; Sieja, K; Stezowski, O; Valiente-Dobon, J J; Vancraeyenest, A; Zheng, Y

    2012-01-01

    We report on the observation of a new isomeric state in $^{68}$Ni. We suggest that the newly observed state at 168(1) keV above the first 2$^+$ state is a $\\pi(2p-2h)$ 0$^{+}$ state across the major Z=28 shell gap. Comparison with theoretical calculations indicates a pure proton intruder configuration and the deduced low-lying structure of this key nucleus suggests a possible shape coexistence scenario involving a highly deformed state.

  20. Anisotropy and oxidative resistance of highly crosslinked UHMWPE after deformation processing by solid-state ram extrusion.

    Science.gov (United States)

    Kurtz, Steven M; Mazzucco, Dan; Rimnac, Clare M; Schroeder, Dave

    2006-01-01

    Solid-state deformation processing is a promising technique for modifying the physical and mechanical properties of highly crosslinked ultra-high molecular weight polyethylene (UHMWPE) beyond simple thermal treatment cycles that have been employed previously. This study evaluates anisotropy and oxidative resistance in a novel, radiation crosslinked (50 kGy) UHMWPE material (ArComXL: Biomet, Inc., Warsaw, IN), incorporating solid-state, deformation processing by extrusion below the melt transition for application in total hip arthroplasty. Tensile, compression, and small punch tests were conducted to evaluate the material properties in the three principal axes of the resulting material. Furthermore, short-term oxidative resistance was evaluated using Fourier transform infrared spectroscopy and the small punch test in conjunction with accelerated shelf aging protocols. The results of this testing indicate that the material is anisotropic, with significantly enhanced strength oriented along the long axis of the rod. For certain other properties, the magnitude of the anisotropy was relatively slight, especially in the elastic regime, in which only a 20% difference was noted between the long axis of the rod and the orthogonal, radial direction. The highly crosslinked material contains detectable free radicals, at a concentration that is 90% less than control, gamma inert sterilized UHMWPE. An unexpected finding of this study was evidence of oxidative stability of the deformation-processed material, even after 4 weeks of accelerated aging in a pressure vessel containing five atmospheres of oxygen (ASTM F2003), which resulted in macroscopic embrittlement of the control material. The oxidative stability observed in ArComXL suggests that the deformation-processed material may be suitable for air-permeable packaging and gas sterilization, which has thus far been reserved for remelted highly crosslinked UHMWPE.

  1. High-resolution X-ray diffraction investigation on the evolution of the substructure of individual austenite grains in TRIP steels during tensile deformation

    NARCIS (Netherlands)

    Blondé, R.J.P.; Jimenez-Melero, E.; Huizenga, R.M.; Zhao, L.; Wright, J.; Brück, E.H.; Van der Zwaag, S.; Van Dijk, N.H.

    2014-01-01

    The martensitic transformation behaviour of the metastable austenite phase in low-alloyed transformation-induced plasticity (TRIP) steels has been studied in situ using high-energy X-ray diffraction during deformation. The austenite stability during tensile deformation has been evaluated at

  2. Mechanisms of plastic deformation in highly cross-linked UHMWPE for total hip components--the molecular physics viewpoint.

    Science.gov (United States)

    Takahashi, Yasuhito; Shishido, Takaaki; Yamamoto, Kengo; Masaoka, Toshinori; Kubo, Kosuke; Tateiwa, Toshiyuki; Pezzotti, Giuseppe

    2015-02-01

    Plastic deformation is an unavoidable event in biomedical polymeric implants for load-bearing application during long-term in-vivo service life, which involves a mass transfer process, irreversible chain motion, and molecular reorganization. Deformation-induced microstructural alterations greatly affect mechanical properties and durability of implant devices. The present research focused on evaluating, from a molecular physics viewpoint, the impact of externally applied strain (or stress) in ultra-high molecular weight polyethylene (UHMWPE) prostheses, subjected to radiation cross-linking and subsequent remelting for application in total hip arthroplasty (THA). Two different types of commercial acetabular liners, which belong to the first-generation highly cross-linked UHMWPE (HXLPE), were investigated by means of confocal/polarized Raman microprobe spectroscopy. The amount of crystalline region and the spatial distribution of molecular chain orientation were quantitatively analyzed according to a combined theory including Raman selection rules for the polyethylene orthorhombic structure and the orientation distribution function (ODF) statistical approach. The structurally important finding was that pronounced recrystallization and molecular reorientation increasingly appeared in the near-surface regions of HXLPE liners with increasing the amount of plastic (compressive) deformation stored in the microstructure. Such molecular rearrangements, occurred in response to external strains, locally increase surface cross-shear (CS) stresses, which in turn trigger microscopic wear processes in HXLPE acetabular liners. Thus, on the basis of the results obtained at the molecular scale, we emphasize here the importance of minimizing the development of irrecoverable deformation strain in order to retain the pristine and intrinsically high wear performance of HXLPE components.

  3. Plastic deformation of high-purity a-titanium: model development and validation using the Taylor cylinder impact test

    Science.gov (United States)

    Chandola, Nitin; Revil-Baudard, Benoit; Cazacu, Oana

    2016-08-01

    Results of an experimental study on the quasi-static and high-rate plastic deformation due to impact of a high-purity, polycrystalline, a-titanium material are presented. To quantify the plastic anisotropy and tension-compression asymmetry of the material, first monotonic uniaxial compression and tension tests were carried out at room temperature under quasi-static conditions. It was found that the material is transversely isotropic and displays strong strength differential effects. To characterize the material's strain rate sensitivity, Split Hopkinson Pressure Bar tests in tension and compression were also conducted. Taylor impact tests were performed for impact velocity of 196 m/s. Plastic deformation extended to 64% of the length of the deformed specimen, with little radial spreading. To model simultaneously the observed anisotropy, strain-rate sensitivity, and tension-compression asymmetry of the material, a three-dimensional constitutive model was developed. Key in the formulation is a macroscopic yield function [1] that incorporates the specificities of the plastic flow, namely the combined effects of anisotropy and tension-compression asymmetry. Comparison between model predictions and data show the capabilities of the model to describe with accuracy the plastic behavior of the a-Ti material for both quasi-static and dynamic loadings, in particular, a very good agreement was obtained between the simulated and experimental post-test Taylor specimen geometries.

  4. Flow Behavior and Microstructural Evolution of 7A85 High-Strength Aluminum Alloy During Hot Deformation

    Science.gov (United States)

    Liu, Xingang; Han, Shuang; Chen, Lei; Yang, Shuai; Jin, Miao; Guo, Baofeng; Mao, Tianhong

    2017-02-01

    Hot deformation behavior of 7A85 high-strength aluminum alloy was investigated at 593 K to 713 K (320 °C to 440 °C) and 0.01-10 s-1. The manifestation of flow curves was related to the strain rate. Typical single-peak curves were shown below 10 s-1, while two stress peaks appeared in the case of 10 s-1 and the second peak strain was almost three times larger than the first one. A constitutive equation considering the effect of strain was developed. Flow stress values predicted by the constitutive model demonstrated a good agreement with the experimental results over the entire range of strain rates and temperatures. Microstructure characterization revealed that dynamic recovery (DRV) and continuous dynamic recrystallization (CDRX) which depended on the Zener-Hollomon parameter (Z) closely, co-occurred at large strain (ɛ = 0.7). With decreasing Z-value, the dominant dynamic restoration mechanism gradually transformed from DRV to CDRX. The average subgrain size (d sub) showed a power-law relationship with Z. Recrystallization was sensitively dependent on the strain rate at above 683 K (410 °C). The fine equiaxed grains appeared at original grain boundaries and in deformed grains interior owing to CDRX. The high-curvature subgrain boundaries can also cause the nucleation of recrystallization within deformed grains.

  5. How Deformation Behavior Controls Product Performance After Twin Screw Granulation With High Drug Loads and Crospovidone as Disintegrant.

    Science.gov (United States)

    Meier, Robin; Moll, Klaus-Peter; Krumme, Markus; Kleinebudde, Peter

    2017-01-01

    This study addresses the quantitative influence of 12 different materials (active pharmaceutical ingredients and excipients as surrogate active pharmaceutical ingredients) on the critical quality attributes of twin screw granulated products and subsequently produced tablets. Prestudies demonstrated the significant influence of the chosen model materials (in combination with crospovidone) on the disintegration behavior of the resulting tablets, despite comparable tablet porosities. This study elucidates possible reasons for the varying disintegration behavior by investigating raw material, granule, and tablet properties. An answer could be found in the mechanical properties of the raw materials and the produced granules. Through compressibility studies, the materials could be classified into materials with high compressibility, which deform rather plastically under compression stress, and low compressibility, which display breakages under compression stress. In general, and apart from (pseudo)-polymorphic transformations, brittle materials featured excellent disintegration performance, even at low resulting tablet porosities <8%, whereas plastically deformable materials mostly did not reveal any disintegration. These findings must be considered in the development of simplified formulations with high drug loads, in which the active pharmaceutical ingredient predominantly defines the deformation behavior of the granule.

  6. Application of high resolution geophysical prospecting to assess the risk related to subsurface deformation in Mexico City

    Science.gov (United States)

    Centeno-Salas, F. A.; Carreón-Freyre, D.; Flores-García, W. A.; Gutiérrez-Calderón, R. I.

    2015-11-01

    In the eastern sector of Mexico City the sub soil consists of high contrasting sequences (lacustrine and volcanic inter bedded deposits) that favor the development of erratic fracturing in the surface causing damage to the urban infrastructure. The high-resolution geophysical prospecting are useful tools for the assessment of ground deformation and fracturing associated with land subsidence phenomena. The GPR method allowed to evaluate the fracture propagation and deformation of vulcano-sedimentary sequences at different depths, the main electrical parameters are directly related with the gravimetric and volumetric water content and therefore with the plasticity of the near surface prospected sequences. The active seismology prospection consisted in a combination of Seismic Refraction (SR) and Multichannel Analysis of Surface Waves (MASW) for the estimation of the velocity of the mechanical compressive (P) and the shear (S) waves. The integration of both methods allowed to estimate the geomechanical parameters characterizing the studied sequence, the Poisson Ratio and the volumetric compressibility. The obtained mechanical parameters were correlated with laboratory measured parameters such as plasticity index, density, shear strength and compressibility and, GPR and seismic profiles were correlated with the mapped fracture systems in the study area. Once calibrated, the profiles allowed to identify the lithological contact between lacustrine and volcanic sequences, their variations of thicknesses in depth and to assess the deformation area in the surface. An accurate determination of the geometry of fracturing was of the most importance for the assessment of the geological risk in the study area.

  7. Effect of Strain Rate on Deformation Behavior of AlCoCrFeNi High-Entropy Alloy by Nanoindentation

    Science.gov (United States)

    Tian, L.; Jiao, Z. M.; Yuan, G. Z.; Ma, S. G.; Wang, Z. H.; Yang, H. J.; Zhang, Y.; Qiao, J. W.

    2016-06-01

    In this study, nanoindentation tests with continuous stiffness measurement technique were measured to investigate the deformation behavior of a high-entropy alloy AlCoCrFeNi under different indentation strain rates at room temperature. Results suggest that the creep behavior exhibits remarkable strain rate dependence. In-situ scanning images showed a conspicuous pileup around the indents, indicating that an extremely localized plastic deformation occurred during the nanoindentation. Under different strain rates, elastic modulus basically remains unchanged, while the hardness decreases with increasing indentation depth due to the indentation size effect. Furthermore, the modulus and hardness of AlCoCrFeNi HEAs are greater than that of the Al x CoCrFeNi ( x = 0.3,0.5) at the strain rate of 0.2 s-1 due to its higher negative enthalpy of mixing related to the atomic binding force, and the solid solution strengthening induced by the lattice distortion, respectively.

  8. Studies on electron-beam irradiation and plastic deformation of medical-grade ultra-high molecular weight polyethylene

    Energy Technology Data Exchange (ETDEWEB)

    Czaja, Krystyna, E-mail: krystyna.czaja@uni.opole.p [Opole University, Faculty of Chemistry, Oleska 48, 45-052 Opole (Poland); SudoL, Marek [Opole University, Faculty of Chemistry, Oleska 48, 45-052 Opole (Poland)

    2011-03-15

    Separated and combined electron-beam irradiation and plastic deformation effects on the structures of ultra-high molecular weight polyethylene (UHMWPE) were studied. It was found that the concentration of carbonyl (ketones, esters and peresters), hydroxyl and vinyl groups increases with the growing dose of adsorbed electrons. It also tends to exhibit a slight increase in the melting point and crystallinity of the samples. A mechanical stress in the polymer was found to accelerate radiation-induced degradation. It was concluded that each of the factors studied (i.e. electron beam sterilization and plastic deformation) had a different impact on the polymer structure. The change in the sequence of action of these factors can dramatically influence the process of UHMWPE destruction. Some effects may be limited or enhanced by the action of other factors. Therefore, the resulting effects of destructive factors depend qualitatively and quantitatively on their intensity and order.

  9. Force balance and deformation characteristics of anisotropic Arctic sea ice (a high resolution study)

    Science.gov (United States)

    Feltham, D. L.; Heorton, H. D.; Tsamados, M.

    2016-12-01

    The spatial distribution of Arctic sea ice arises from its deformation, driven by external momentum forcing, thermodynamic growth and melt. The deformation of Arctic sea ice is observed to have structural alignment on a broad range of length scales. By considering the alignment of diamond-shaped sea ice floes, an anisotropic rheology (known as the Elastic Anisotropic Plastic, EAP, rheology) has been developed for use in a climate sea ice model. Here we present investigations into the role of anisotropy in determining the internal ice stress gradient and the complete force balance of Arctic sea ice using a state-of-the-art climate sea ice model. Our investigations are focused on the link between external imposed dynamical forcing, predominantly the wind stress, and the emergent properties of sea ice, including its drift speed and thickness distribution. We analyse the characteristics of deformation events for different sea ice states and anisotropic alignment over different regions of the Arctic Ocean. We present the full seasonal stress balance and sea ice state over the Arctic ocean. We have performed 10 km basin-scale simulations over a 30-year time scale, and 2 km and 500 m resolution simulations in an idealised configuration. The anisotropic EAP sea ice rheology gives higher shear stresses than the more customary isotropic EVP rheology, and these reduce ice drift speed and mechanical thickening, particularly important in the Archipelago. In the central Arctic the circulation of sea ice is reduced allowing it to grow thicker thermodynamically. The emergent stress-strain rate correlations from the EAP model suggest that it is possible to characterise the internal ice stresses of Arctic sea ice from observable basin-wide deformation and drift patterns.

  10. Monitoring microstructural evolution in-situ during cyclic deformation by high resolution reciprocal space mapping

    DEFF Research Database (Denmark)

    Diederichs, Annika Martina; Thiel, Felix; Fischer, Torben

    2017-01-01

    is gained by in-situ monitoring of the microstructural evolution during cyclic deformation. By HRRSM, a large number of individual subgrains can be resolved within individual grains in the bulk of polycrystalline specimens and their fate, their individual orientation and elastic stresses, tracked during...... different loading regimes as tension and compression. With this technique, the evolution of dislocation structures in selected grains was followed during an individual load cycle....

  11. Highly Deformable Energy-Dissipating Reinforced Concrete Elements in Seismic Design of Reinforced Concrete Structures

    Directory of Open Access Journals (Sweden)

    Momoh Emmanuel Owoichoechi

    2017-06-01

    Full Text Available Incorporating scrap tyre rubber particles as partial replacement for aggregates has been found to produce concrete with improved ductility, deformability and damping which are desired characteristics of a viable material for enhancing structural response to earthquake vibrations. An analytical study using Drain-2dX was carried out to investigate the response of 4-storey, 3-bay reinforced concrete frames on innovative rubberised concrete deformable foundation models to simulated earthquake scaled to 5 different peak ground accelerations. Stress-strain properties of 3-layers aramid fibre-reinforced polymer (FRP-confinement for concrete incorporating waste rubber from scrap vehicle tyres were used to model the elements of this foundation models. With a partial decoupling of the superstructure from the direct earthquake force, the models showed up to 70% reduction in base shear, an improved overall q-factor of 7.1, and an estimated frame acceleration of 0.11g for an earthquake peak ground acceleration of 0.44g. This implies that a non-seismically designed reinforced concrete frame on the proposed rubberised concrete deformable foundation system would provide a simple, affordable and equally efficient alternative to the conventional and usually expensive earthquake resistant concrete frames. A supplementary Arrest System (SAS was proposed to anchor the frame from the resulting soft storey at the rubberised concrete foundation. A further research is recommended for the design of concrete hinges with rubberised concrete as used in the model with the most impressive response.

  12. Investigation of work softening mechanisms and texture in a hot deformed 6061 aluminum alloy at high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Ezatpour, H.R., E-mail: H.R.Ezatpour@gmail.com [Department of Materials Science and Metallurgical Engineering, Engineering Faculty, Ferdowsi University of Mashhad, Mashhad (Iran, Islamic Republic of); Haddad Sabzevar, M.; Sajjadi, S.A. [Department of Materials Science and Metallurgical Engineering, Engineering Faculty, Ferdowsi University of Mashhad, Mashhad (Iran, Islamic Republic of); Huang, Yz., E-mail: yzhuang@ntu.edu.sg [School of Materials Science and Engineering, Nanyang Technological University, Singapore 639798 (Singapore)

    2014-06-01

    Hot deformation behavior of 6061 aluminum alloy was investigated by performing compression test in the temperature range of 350–500 °C. Equivalent strain rates were selected in the range of 0.0005–0.5 s{sup −1} in order to obtain processing and stability maps of the studied material using a Dynamic Material Model. Microstructure of the samples after deformation was analyzed by light and electron microscopy and the differences were compared together. The stresses obtained from the flow curves were related to strain rate (ε) and temperature (T) by a constitutive equation in hyperbolic sine function with hot deformation activation energy of 274 kJ/mol, and were described by the Zener–Hollomon equation. Microstructure results showed that with decreasing Z value, the elongated grains coarsened and the tendency of dynamic recrystallization enhanced. Correspondingly, the subgrain size increased and the dislocation density decreased. Moreover, the main softening mechanism of the alloy transformed from dynamic recovery to dynamic recrystallization. XRD results showed that the (200) texture has an important role in development of dynamic recystallization at high temperature.

  13. EFFECTS OF HIGH-DENSITY CURRENT PULSES ON WORKHARDENING BEHAVIORS OF AUSTENITE STAINLESS STEELIN WIRE-DRAWING DEFORMATION

    Institute of Scientific and Technical Information of China (English)

    K.F. Yao; P. Yu; J. Wang; W. Fang; M.X. Zheng

    2001-01-01

    The influence of high-density palsing current on the work-hardening behavior of H0Cr17Ni6Mn3 and 1Cr18Ni9 stainless steels in wire-drawing deformation processes has been studied. It was found that the drawing stress and the work-hardening rate of wires were significantly reduced by applying current pulses in drawing process. The work-hardening behavior of the multi-courses drawing deformation can be well described by Hollomon formula σ = kεn. With the application of current pulses in drawing deformation, the work-hardening exponents of H0Cr17Ni6Mn3 steel wires and 1Cr18Ni9 stainless steel wires were reduced by 33% and 45%, respectively, and their work-hardening coefficients were reduced by 41% and 47%, respectively. It was also found that the work-hardening coefficient of wires was reduced with the increment of the frequency of current pulses, while the work-hardening exponents of both steels were insensitive to the pulsing frequency.``

  14. Plastic deformation of FeSi at high pressures: implications for planetary cores

    Science.gov (United States)

    Kupenko, Ilya; Merkel, Sébastien; Achorner, Melissa; Plückthun, Christian; Liermann, Hanns-Peter; Sanchez-Valle, Carmen

    2017-04-01

    The cores of terrestrial planets is mostly comprised of a Fe-Ni alloy, but it should additionally contain some light element(s) in order to explain the observed core density. Silicon has long been considered as a likely candidate because of geochemical and cosmochemical arguments: the Mg/Si and Fe/Si ratios of the Earth does not match those of the chondrites. Since silicon preferentially partition into iron-nickel metal, having 'missing' silicon in the core would solve this problem. Moreover, the evidence of present (e.g. Mercury) or ancient (e.g. Mars) magnetic fields on the terrestrial planets is a good indicator of (at least partially) liquid cores. The estimated temperature profiles of these planets, however, lay below iron melting curve. The addition of light elements in their metal cores could allow reducing their core-alloy melting temperature and, hence, the generation of a magnetic field. Although the effect of light elements on the stability and elasticity of Fe-Ni alloys has been widely investigated, their effect on the plasticity of core materials remains largely unknown. Yet, this information is crucial for understanding how planetary cores deform. Here we investigate the plastic deformation of ɛ-FeSi up to 50 GPa at room temperature employing a technique of radial x-ray diffraction in diamond anvil cells. Stoichiometric FeSi endmember is a good first-order approximation of the Fe-FeSi system and a good starting material to develop new experimental perspectives. In this work, we focused on the low-pressure polymorph of FeSi that would be the stable phase in the cores of small terrestrial planets. We will present the analysis of measured data and discuss their potential application to constrain plastic deformation in planetary cores.

  15. Remote Sensing of Deformation of a High Concrete-Faced Rockfill Dam Using InSAR: A Study of the Shuibuya Dam, China

    Directory of Open Access Journals (Sweden)

    Wei Zhou

    2016-03-01

    Full Text Available Settlement is one of the most important deformation characteristics of high concrete faced rockfill dams (CFRDs, >100 m. High CFRDs safety would pose a great threat to the security of people’s lives and property downstream if this kind of deformation were not to be measured correctly, as traditional monitoring approaches have limitations in terms of durability, coverage, and efficiency. It has become urgent to develop new monitoring techniques to complement or replace traditional monitoring approaches for monitoring the safety and operation status of high CFRDs. This study examines the Shuibuya Dam (up to 233.5 m in height in China, which is currently the highest CFRD in the world. We used space-borne Interferometric Synthetic Aperture Radar (InSAR time series to monitor the surface deformation of the Shuibuya Dam. Twenty-one ALOS PALSAR images that span the period from 28 February 2007 to 11 March 2011 were used to map the spatial and temporal deformation of the dam. A high correlation of 0.93 between the InSAR and the in-situ monitoring results confirmed the reliability of the InSAR method; the deformation history derived from InSAR is also consistent with the in-situ settlement monitoring system. In addition, the InSAR results allow continuous investigation of dam deformation over a wide area that includes the entire dam surface as well as the surrounding area, offering a clear picture continuously of the dam deformation.

  16. The use of a high-order MEMS deformable mirror in the Gemini Planet Imager

    Energy Technology Data Exchange (ETDEWEB)

    Poyneer, L A; Bauman, B; Cornelissen, S; Jones, S; Macintosh, B; Palmer, D; Isaacs, J

    2010-12-17

    We briefly review the development history of the Gemini Planet Imager's 4K Boston Micromachines MEMS deformable mirror. We discuss essential calibration steps and algorithms to control the MEMS with nanometer precision, including voltage-phase calibration and influence function characterization. We discuss the integration of the MEMS into GPI's Adaptive Optics system at Lawrence Livermore and present experimental results of 1.5 kHz closed-loop control. We detail mitigation strategies in the coronagraph to reduce the impact of abnormal actuators on final image contrast.

  17. High-precision system identification method for a deformable mirror in wavefront control.

    Science.gov (United States)

    Huang, Lei; Ma, Xingkun; Bian, Qi; Li, Tenghao; Zhou, Chenlu; Gong, Mali

    2015-05-10

    Based on a mathematic model, the relation between the accuracy of the influence matrix and the performance of the wavefront correction is established. Based on the least squares method, a two-step system identification is proposed to improve the accuracy of the influence matrix, where the measurement noise can be suppressed and the nonlinearity of the deformable mirror can be compensated. The validity of the two-step system identification method is tested in the experiment, where improvements in wavefront correction precision as well as closed-loop control efficiency were observed.

  18. High-speed deformation measurement using spatially phase-shifted speckle interferometry

    Science.gov (United States)

    Beckmann, Tobias; Fratz, Markus; Bertz, Alexander; Carl, Daniel

    2014-02-01

    Electronic speckle pattern interferometry (ESPI) is a powerful technique for differential shape measurement with submicron resolution. Using spatial phase-shifting (SPS), no moving parts are required, allowing frame acquisition rates limited by camera hardware. We present ESPI images of 1 megapixel resolution at 500 fps. Analysis of SPS data involves complex, time-consuming calculations. The graphics processing units found in state-of-the-art personal computers have exceptional parallel processing capabilities, allowing real-time SPS measurements at video frame rates. Deformation analysis at this frame rate can be used to analyze transient phenomena such as transient temperature effects in integrated circuit chips or during material processing.

  19. Relationship between boundary misorientation angle and true strain during high temperature deformation of 7050 aluminum alloy

    Institute of Scientific and Technical Information of China (English)

    HU Hui-e; YANG Li; ZHEN Liang; SHAO Wen-zhu; ZHANG Bao-you

    2008-01-01

    Tensile tests of solid solution treated 7050 aluminum alloy were conducted to different strain degrees (0.1, 0.4, 0.6 and failure) at 460 ℃ with the strain rate of 1.0×10-4-1.0×10-1s-1. The boundary misorientation angle evolution during hot deformation of the 7050 aluminum alloy was studied by EBSD technique and the fracture surfaces were observed using SEM. A linear relationship between the increase in the average boundary misorientation angle and the true strain at different strain rates is assumed when aluminum alloy is deformed at 460 ℃. The increasing rate of average boundary misorientation angle is 15.1-, 15.7- and -0.75- corresponding to the strain rate of 1.0×10-4, 1.0×10-2 and 0.1 s-1, respectively. The main softening mechanism is continuous dynamic recrystallization when the strain rates are 1.0×10-4 and 1.0×10-2 s-1, and it is dynamic recovery when strain rate is 0.1 s-1.

  20. Microstructure characterization of high-purity aluminum processed by dynamic severe plastic deformation

    Energy Technology Data Exchange (ETDEWEB)

    Dirras, Guy; Chauveau, Thierry; Ramtani, Salah; Bui, Quang-Hien [LPMTM, CNRS, UPR 9001, Universite Paris 13, 99 avenue J. B. Clement, 93430 Villetaneuse (France); Abdul-Latif, Akrum [Laboratoire d' Ingenierie des Systemes Mecaniques et des Materiaux, 3 rue Fernand Hainaut, 93407 St Ouen Cedex (France)

    2010-10-15

    Fine-grained aluminum (700-1000 nm) was processed by dynamic severe plastic deformation of coarse-grained (3 mm) pure aluminum (99.999 wt.%). The resulting microstructure was characterized by transmission electron microscopy (TEM) and X-ray profile analyses. It is observed that the grain size determined by TEM departs from measurements made by X-ray profile analysis. In the latter case, the average crystallite size determined over the global crystallographic or on the deformation-induced texture components, namely {l_brace}123{r_brace} left angle 751 right angle, {l_brace}100{r_brace} left angle 011 right angle, and {l_brace}223{r_brace} left angle 154 right angle, yields similar values ({proportional_to}225 nm). By contrast, the dislocation density determined on these texture components is about two times higher than the one measured on the global texture. The difference might be related to the specificities of the induced crystallographic texture. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  1. Analysis on flow stress of magnesium alloys during high temperature deformation

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The flow stress of magnesium alloys during hot compression at different temperatures and strain rates was studied by experiments. Materials used were AZ91D alloys in as-cast, homogeneous treatment states, AZ31 and ZK60 alloys in as-cast state.The results show that the thermal simulation curves of different alloys differ from one another at the same deforming condition. The general curves of AZ31 and AZ91D alloys have the character of dynamic recrystallization. There are increase of true stress, drastic falling of true stress and increase of true stress in most curves of ZK60 alloy, while the other curves have the characteristics of dynamic recrystallization. From the analysis the reasonable deforming temperature should be selected from 523 to 673 K for AZ31 and the unhomogenized AZ91D alloy, from 473 to 673 K for the homogenized AZ91D alloy, and it was concluded to be 473 K or 673 K for ZK60 alloy.

  2. Inelastic deformation and damage at high temperature. Progress report, April 1, 1991--March 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Krempl, E.

    1992-05-01

    Combined experimental and theoretical investigations into the inelastic deformation and damage behavior of engineering alloys at elevated temperatures are being pursued. The analysis of previously performed strain rate change and relaxation tests on modified 9Cr-1Mo steel showed the need for inclusion of a recovery of state term in the growth laws for the state variables of the viscoplasticity theory based on overstress (VBO). Recovery of state terms were introduced and the experimental results were satisfactorily simulated. The finite deformation theory of VBO has been developed further to include a convected derivative rationale for the choice of the objective stress rate. The reversing direct current voltage drop measurements during low cycle fatigue at elevated temperature were improved. A passive filter bank and new positioning devices for the coils were installed. Tests at 650{degrees}C and lasting several days showed excessive, uncontrollable temperature changes. It was decided to drop the test temperature to 538{degrees}C which is close to the operating temperature of Type 304 Stainless Steel. The temperature fluctuations in torsion tests were within {plus_minus}3{degrees}C which was considered satisfactory. Testing will continue at 538{degrees}C.

  3. Deformability measurement of red blood cells using a microfluidic channel array and an air cavity in a driving syringe with high throughput and precise detection of subpopulations.

    Science.gov (United States)

    Kang, Yang Jun; Ha, Young-Ran; Lee, Sang-Joon

    2016-01-07

    Red blood cell (RBC) deformability has been considered a potential biomarker for monitoring pathological disorders. High throughput and detection of subpopulations in RBCs are essential in the measurement of RBC deformability. In this paper, we propose a new method to measure RBC deformability by evaluating temporal variations in the average velocity of blood flow and image intensity of successively clogged RBCs in the microfluidic channel array for specific time durations. In addition, to effectively detect differences in subpopulations of RBCs, an air compliance effect is employed by adding an air cavity into a disposable syringe. The syringe was equally filled with a blood sample (V(blood) = 0.3 mL, hematocrit = 50%) and air (V(air) = 0.3 mL). Owing to the air compliance effect, blood flow in the microfluidic device behaved transiently depending on the fluidic resistance in the microfluidic device. Based on the transient behaviors of blood flows, the deformability of RBCs is quantified by evaluating three representative parameters, namely, minimum value of the average velocity of blood flow, clogging index, and delivered blood volume. The proposed method was applied to measure the deformability of blood samples consisting of homogeneous RBCs fixed with four different concentrations of glutaraldehyde solution (0%-0.23%). The proposed method was also employed to evaluate the deformability of blood samples partially mixed with normal RBCs and hardened RBCs. Thereafter, the deformability of RBCs infected by human malaria parasite Plasmodium falciparum was measured. As a result, the three parameters significantly varied, depending on the degree of deformability. In addition, the deformability measurement of blood samples was successfully completed in a short time (∼10 min). Therefore, the proposed method has significant potential in deformability measurement of blood samples containing hematological diseases with high throughput and precise detection of

  4. An adjoint method for a high-order discretization of deforming domain conservation laws for optimization of flow problems

    Science.gov (United States)

    Zahr, M. J.; Persson, P.-O.

    2016-12-01

    The fully discrete adjoint equations and the corresponding adjoint method are derived for a globally high-order accurate discretization of conservation laws on parametrized, deforming domains. The conservation law on the deforming domain is transformed into one on a fixed reference domain by the introduction of a time-dependent mapping that encapsulates the domain deformation and parametrization, resulting in an Arbitrary Lagrangian-Eulerian form of the governing equations. A high-order discontinuous Galerkin method is used to discretize the transformed equation in space and a high-order diagonally implicit Runge-Kutta scheme is used for the temporal discretization. Quantities of interest that take the form of space-time integrals are discretized in a solver-consistent manner. The corresponding fully discrete adjoint method is used to compute exact gradients of quantities of interest along the manifold of solutions of the fully discrete conservation law. These quantities of interest and their gradients are used in the context of gradient-based PDE-constrained optimization. The adjoint method is used to solve two optimal shape and control problems governed by the isentropic, compressible Navier-Stokes equations. The first optimization problem seeks the energetically optimal trajectory of a 2D airfoil given a required initial and final spatial position. The optimization solver, driven by gradients computed via the adjoint method, reduced the total energy required to complete the specified mission nearly an order of magnitude. The second optimization problem seeks the energetically optimal flapping motion and time-morphed geometry of a 2D airfoil given an equality constraint on the x-directed impulse generated on the airfoil. The optimization solver satisfied the impulse constraint to greater than 8 digits of accuracy and reduced the required energy between a factor of 2 and 10, depending on the value of the impulse constraint, as compared to the nominal configuration.

  5. Mechanical energy losses in plastically deformed and electron plus neutron irradiated high purity single crystalline molybdenum at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Zelada, Griselda I. [Laboratorio de Materiales, Escuela de Ingenieria Electrica, Facultad de Ciencias Exactas, Ingenieria y Agrimensura, Universidad Nacional de Rosario, Avda. Pellegrini 250, 2000 Rosario (Argentina); Lambri, Osvaldo Agustin [Laboratorio de Materiales, Escuela de Ingenieria Electrica, Facultad de Ciencias Exactas, Ingenieria y Agrimensura, Universidad Nacional de Rosario, Avda. Pellegrini 250, 2000 Rosario (Argentina); Instituto de Fisica Rosario - CONICET, Member of the CONICET& #x27; s Research Staff, Avda. Pellegrini 250, 2000 Rosario (Argentina); Bozzano, Patricia B. [Laboratorio de Microscopia Electronica, Unidad de Actividad Materiales, Centro Atomico Constituyentes, Comision Nacional de Energia Atomica, Avda. Gral. Paz 1499, 1650 San Martin (Argentina); Garcia, Jose Angel [Departamento de Fisica Aplicada II, Facultad de Ciencias y Tecnologia, Universidad del Pais Vasco, Apdo. 644, 48080 Bilbao, Pais Vasco (Spain)

    2012-10-15

    Mechanical spectroscopy (MS) and transmission electron microscopy (TEM) studies have been performed in plastically deformed and electron plus neutron irradiated high purity single crystalline molybdenum, oriented for single slip, in order to study the dislocation dynamics in the temperature range within one third of the melting temperature. A damping peak related to the interaction of dislocation lines with both prismatic loops and tangles of dislocations was found. The peak temperature ranges between 900 and 1050 K, for an oscillating frequency of about 1 Hz. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  6. High-temperature plastic deformation of fine-grained Y-doped BaCeO{sub 3} polycrystals

    Energy Technology Data Exchange (ETDEWEB)

    Vaquero-Aguilar, C; Jimenez-Melendo, M [Departamento de Fisica de la Materia Condensada, Universidad de Sevilla. Aptdo. 1065. 41080 Sevilla (Spain); Real, C, E-mail: melendo@us.e [Instituto de Ciencia de Materiales de Sevilla, Centro Mixto CSIC-US, Av. Americo Vespucio 49. 41092 Sevilla (Spain)

    2010-07-01

    The high-temperature plastic deformation of BaCe{sub 0.95}Y{sub 0.05}O{sub 3-{delta}} polycrystals with average grain size of 0.50 {mu}m has been studied in compression between 1000 and 1250{sup 0}C in air at different initial strain rates. The stress-strain curves display yield drop at strains close to 5%, followed by steady state or strain-softening stages. Large ductilities were achieved at the higher temperatures, without appreciable changes in grain shape and size. Mechanical data and microstructural observations are consistent with a flow mechanism by grain boundary sliding.

  7. Subgrain and dislocation structure changes in hot-deformed high-temperature Fe-Ni austenitic alloy

    Energy Technology Data Exchange (ETDEWEB)

    Ducki, K.J.; Rodak, K.; Hetmanczyk, M.; Kuc, D

    2003-08-28

    The influence of plastic deformation on the substructure of a high-temperature austenitic Fe-Ni alloy has been presented. Hot-torsion tests were executed at constant strain rates of 0.1 and 1.0 s{sup -1}, at testing temperatures in the range 900-1150 deg. C. The examination of the microstructure was carried out, using transmission electron microscopy. Direct measurements on the micrographs allowed the calculation of structural parameters: the average subgrain area, and the mean dislocation density. A detailed investigation has shown that the microstructure is inhomogeneous, consisting of dense dislocation walls, subgrains and recrystallized regions.

  8. High-Frequency CTD Measurements for Accurate GPS/acoustic Sea-floor Crustal Deformation Measurement System

    Science.gov (United States)

    Tadokoro, K.; Yasuda, K.; Taniguchi, S.; Uemura, Y.; Matsuhiro, K.

    2015-12-01

    The GPS/acoustic sea-floor crustal deformation measurement system has developed as a useful tool to observe tectonic deformation especially at subduction zones. One of the factors preventing accurate GPS/acoustic sea-floor crustal deformation measurement is horizontal heterogeneity of sound speed in the ocean. It is therefore necessary to measure the gradient directly from sound speed structure. We report results of high-frequency CTD measurements using Underway CTD (UCTD) in the Kuroshio region. We perform the UCTD measurements on May 2nd, 2015 at two stations (TCA and TOA) above the sea-floor benchmarks installed across the Nankai Trough, off the south-east of Kii Peninsula, middle Japan. The number of measurement points is six at each station along circles with a diameter of 1.8 nautical miles around the sea-floor benchmark. The stations TCA and TOA are located on the edge and the interior of the Kuroshio current, respectively, judging from difference in sea water density measured at the two stations, as well as a satellite image of sea-surface temperature distribution. We detect a sound speed gradient of high speeds in the southern part and low speeds in the northern part at the two stations. At the TCA station, the gradient is noticeable down to 300 m in depth; the maximum difference in sound speed is +/- 5 m/s. The sound speed difference is as small as +/- 1.3 m/s at depths below 300 m, which causes seafloor benchmark positioning error as large as 1 m. At the TOA station, the gradient is extremely small down to 100 m in depth. The maximum difference in sound speed is less than +/- 0.3 m/s that is negligible small for seafloor benchmark positioning error. Clear gradient of high speed is observed to the depths; the maximum difference in sound speed is +/- 0.8-0.9 m/s, causing seafloor benchmark positioning error of several tens centimeters. The UCTD measurement is effective tool to detect sound speed gradient. We establish a method for accurate sea

  9. Thermal behavior of Ni (99.967% and 99.5% purity) deformed to an ultra-high strain by high pressure torsion

    DEFF Research Database (Denmark)

    Zhang, H.W.; Huang, Xiaoxu; Pippan, R.

    2010-01-01

    Polycrystalline Ni of two purities (99.967% (4N) and 99.5% (2N)) was deformed to an ultra-high strain of εvM = 100 (εvM, von Mises strain) by high pressure torsion at room temperature. The 4N and 2N samples at this strain are nanostructured with an average boundary spacing of 100 nm, a high density...... Ni, respectively. The isochronal annealing leads to a drop in hardness in three stages: a relatively small decrease at low temperatures (recovery), followed by a rapid decrease at intermediate temperatures (recrystallization) and a slow decrease at high temperature (grain growth). Both recovery...

  10. The large volume press facility at ID06 beamline of the European synchrotron radiation facility as a High Pressure-High Temperature deformation apparatus.

    Science.gov (United States)

    Guignard, Jeremy; Crichton, Wilson A

    2015-08-01

    We report here the newly developed deformation setup offered by the 20MN (2000T) multi-anvil press newly installed at sector 7 of the European synchrotron radiation facility, on the ID06 beamline. The press is a Deformation-DIA (D-DIA) type apparatus, and different sets of primary anvils can be used for deformation experiments, from 6 mm to 3 mm truncations, according to the target pressure needed. Pressure and temperature calibrations and gradients show that the central zone of the assemblies is stable. Positions of differential RAMs are controlled with a sub-micron precision allowing strain rate from 10(-4) to 10(-6) s(-1). Moreover, changing differential RAM velocity is immediately visible on sample, making faster reaching of steady state. Lattice stresses are determined by the shifting of diffraction peak with azimuth angle using a linear detector covering typically a 10° solid-angle in 2θ mounted on rotation perpendicular to the beam. Acquisition of diffraction pattern, at a typical energy of 55 keV, is less than a minute to cover the whole azimuth-2θ space. Azimuth and d-spacing resolution are respectively better than 1° and 10(-3) Å making it possible to quantify lattice stresses with a precision of ±20 MPa (for silicates, which have typically high values of elastic properties), in pure or simple shear deformation measurements. These mechanical data are used to build fully constrained flow laws by varying P-T-σ-ε̇ conditions with the aim to better understanding the rheology of Earth's mantle. Finally, through texture analysis, it is also possible to determine lattice preferred orientation during deformation by quantifying diffraction peak intensity variation with azimuth angle. This press is therefore included as one of the few apparatus that can perform such experiments combining with synchrotron radiation.

  11. Behavior of highly deformable relaxor-ferroelectric-based ceramics in an electric field

    Science.gov (United States)

    Talanov, M. V.; Reznichenko, L. A.

    2013-10-01

    The deformation characteristics of multicomponent barium-doped piezoelectric ceramics mPbMg1/3Nb2/3O3- n PbNi1/3Nb2/3O3- y PbZn1/3Nb2/3O3- x PbTiO3 are studied in electric fields E = 0-12 kV/cm. Anomalies are detected in the dependences of elastic strain ξ3 and piezoelectric modulus d {33/eff} on the external dc electric field. The history of the materials is shown to affect the change of piezoelectric modulus d {33/eff} in an electric field. The revealed dependences are used to propose a method to increase the efficiency of operation of piezoelectric actuators.

  12. The origin of high hydraulic resistance for filter cakes of deformable particles: cell-bed deformation or surface-layer effect?

    OpenAIRE

    Meireles, Martine; Molle, Catherine; Clifton, Michael J.; Aimar, Pierre

    2004-01-01

    International audience; This study reports a numerical approach for modeling the hydraulic resistance of a filter cake of deformable cells. First, a mechanical and osmotic model that describes the volume fraction of solids in a bed of yeast cells as a function of the compressive pressure it experiences is presented. The effects of pressure on the compressibility of yeast cells beds were further investigated both by filtration experiments and by centrifugal experiments based on the multiple sp...

  13. STUDY OF NUMERICAL MODELING OF SHAPE DEFORMING ZONE OF DIES, DURING DRAWING HIGH CARBON STEEL WIRE TO THE TEMPERATURE AND THE STRESS-STRAIN STATE IN THE WIRE AND DIE

    Directory of Open Access Journals (Sweden)

    O. L. Bobarikin

    2012-01-01

    Full Text Available Investigation by numerical modeling of influence of the form of deforming zone of die at drawing of steel high- carbon wire on temperature and strained-deformed state in wire and die is carried out.

  14. High rate and high spatial resolution surface deformation monitoring of the Argentiere glacier from complementary remote sensing and geodetic data

    Science.gov (United States)

    Benoit, Lionel; Pham, Ha-Thai; Trouvé, Emmanuel; Vernier, Flavien; Moreau, Luc; Martin, Olivier; Thom, Christian; Briole, Pierre

    2014-05-01

    The Argentière glacier in the French Alps (Mont-Blanc massif) is a 10 km long glacier covering 19 km². Its flow on a large scale has been studied for over a hundred years by glaciologists, but the time and space fluctuations of its flow are still poorly documented. We selected a small area of the glacier, about 1 km upstream of the Lognan serac fall to measure the glacier flow with in-situ GPS measurements combined with time series of ground based pictures and time series of synthetic aperture radar images from the TerreSAR-X satellite. The experiment took place during two months between September and November 2013 with a network of thirteen single-frequency GPS receivers (eleven set up on the glacier and two on the nearby bedrock) deployed in the field with a sampling rate of 30s. Our data processing allows us to estimate epoch by epoch coordinates of each GPS site with a centimetric precision. The main interest of this approach is twofold : the monitoring of the temporal evolution of the flow and the providing of ground control points for the local and satellite remote sensing imagery. The average velocities of the stations is around 15 cm/day with peaks reaching 25cm/day lasting a few hours to one day after rainfalls or cooling periods. We explain these accelerations as the consequence of an increased basal water pressure. The strain tensor analysis shows a good consistency between the main strain axis and the orientation of the cracks on both sides of the glacier. However, available only at eleven points, the GPS data can not in any case give a picture of the overall deformation of the glacier. In order to map the glacier flow as a whole, including crevasse areas or serac falls, two automatic digital cameras were installed during the experiment on the bedrock on the shore of the glacier with acquisitions every three hours during day time. The processing of the stereo pairs produces maps in which the pixels coordinates (and their changes) are estimated with a

  15. Influence of pre-deformation, sensitization and oxidation in high temperature water on corrosion resistance of AISI 304 stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Lv, Jinlong, E-mail: ljltsinghua@126.com [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Liang, Tongxiang [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Luo, Hongyun [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beijing University of Aeronautics and Astronautics, Xueyuan Road 37, Beijing 100191 (China)

    2016-12-01

    Highlights: • The pre-strain accelerated desensitization and sensitization for austenitic stainless steels. • Low temperature sensitization (carbide precipitation) induced α′-martensite. • The sensitization level could affect directly corrosion resistance of the oxide film. - Abstract: The effects of pre-deformation on sensitization of AISI 304 stainless steel were investigated by the double loop electrochemical potentiokinetic reactivation test. The effects of pre-deformation and sensitization on high temperature oxidized film formed in high temperature water were analyzed by a XRD and SEM. The electrochemical impedance spectroscopy at room temperature was used to study corrosion resistance of oxidized film. The point defect density of oxidized film was calculated by Mott–Schottky plots. The results showed that the value of the degree of sensitization first decreased and then slight increased with the increasing of engineering strain. Moreover, low temperature promoted to form sensitization induced “secondary” α′-martensite. The sample with 20% engineering strain had higher impedance value than other samples. The result was supported by further Mott–Schottky experiments. Considering increased α′-martensite with the increasing of strain, the results of the impedance were more consistent with values of the degree of sensitization.

  16. Microstructure and high temperature deformation of an ultra-fine grained ECAP AA7075 aluminium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Malek, Premysl; Turba, Krystof; Cieslar, Miroslav; Harcuba, Petr [Charles Univ., Prague (Czech Republic). Dept. of Physics of Materials

    2013-01-15

    An AA 7075 aluminium alloy with an ultra-fine grained structure was prepared through equal channel angular pressing (ECAP) at pressing temperatures T ECAP of 120, 170, and 220 C. A decrease in T{sub ECAP} from 220 to 120 C was found to lead to a more pronounced refinement of the microstructure and to worse stability of the microstructure - the onset of grain coarsening was displaced to lower temperatures. The material pressed with the highest T{sub ECAP} exhibited superplastic behaviour at temperatures close to 400 C and grain boundary sliding was identified as the dominant operating deformation mechanism. The materials prepared with both of the lower T{sub ECAP} exhibited only enhanced ductility of about 200%, however this behaviour was observed at temperatures as low as 200 C. It was found that this 'low temperature superplasticity' resulted from a combined operation of grain boundary sliding at selected grain boundaries and glide of lattice dislocations. (orig.)

  17. Effect of texture and heat treatment on high temperature deformation of Zircaloy-2

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, E.F. (Atomic Energy of Canada Ltd., Chalk River, Ontario. Chalk River Nuclear Labs.); Choubey, R. (Combustion Engineering-Superheater Ltd., Moncton, New Brunswick (Canada)); Jonas, J.J. (McGill Univ., Montreal, Quebec (Canada). Dept. of Metallurgical Engineering)

    1984-09-01

    Cylindrical specimens machined from Zircaloy-2 plate have been tested under compression at 295, 675 and 1075 K. The plate was in three conditions (a) as hot rolled, (b) oil quenched from 1130 K and (c) oil quenched from 1340 K. These conditions simulate the structures in fuel cladding in regions near brazed spacers. The structures and crystallographic textures of the material in these conditions were characterized. Specimens with axes along the longitudinal, transverse and thickness directions were tested to determine the effect of temperature, texture and structure on the mechanical properties, particularly with respect to postulated LOCA conditions. The tests showed that (I) factors for mechanical anisotropy derived from room temperature results should be valid for LOCA analysis, (II) anisotropy factors from the results are consistent with about 67% prism and 33% basal slip in the early stages of deformation and (III) oil quenching from 1130 K changes the texture and strength in a minor way, while quenching from 1340 K (..beta.. phase) gives an almost random texture, little mechanical anisotropy and a small change in the average strength.

  18. Cyclic Deformation of Advanced High-Strength Steels: Mechanical Behavior and Microstructural Analysis

    Science.gov (United States)

    Hilditch, Timothy B.; Timokhina, Ilana B.; Robertson, Leigh T.; Pereloma, Elena V.; Hodgson, Peter D.

    2009-02-01

    The fatigue properties of multiphase steels are an important consideration in the automotive industry. The different microstructural phases present in these steels can influence the strain life and cyclic stabilized strength of the material due to the way in which these phases accommodate the applied cyclic strain. Fully reversed strain-controlled low-cycle fatigue tests have been used to determine the mechanical fatigue performance of a dual-phase (DP) 590 and transformation-induced plasticity (TRIP) 780 steel, with transmission electron microscopy (TEM) used to examine the deformed microstructures. It is shown that the higher strain life and cyclic stabilized strength of the TRIP steel can be attributed to an increased yield strength. Despite the presence of significant levels of retained austenite in the TRIP steel, both steels exhibited similar cyclic softening behavior at a range of strain amplitudes due to comparable ferrite volume fractions and yielding characteristics. Both steels formed low-energy dislocation structures in the ferrite during cyclic straining.

  19. Full-frame, high-speed 3D shape and deformation measurements using stereo-digital image correlation and a single color high-speed camera

    Science.gov (United States)

    Yu, Liping; Pan, Bing

    2017-08-01

    Full-frame, high-speed 3D shape and deformation measurement using stereo-digital image correlation (stereo-DIC) technique and a single high-speed color camera is proposed. With the aid of a skillfully designed pseudo stereo-imaging apparatus, color images of a test object surface, composed of blue and red channel images from two different optical paths, are recorded by a high-speed color CMOS camera. The recorded color images can be separated into red and blue channel sub-images using a simple but effective color crosstalk correction method. These separated blue and red channel sub-images are processed by regular stereo-DIC method to retrieve full-field 3D shape and deformation on the test object surface. Compared with existing two-camera high-speed stereo-DIC or four-mirror-adapter-assisted singe-camera high-speed stereo-DIC, the proposed single-camera high-speed stereo-DIC technique offers prominent advantages of full-frame measurements using a single high-speed camera but without sacrificing its spatial resolution. Two real experiments, including shape measurement of a curved surface and vibration measurement of a Chinese double-side drum, demonstrated the effectiveness and accuracy of the proposed technique.

  20. Pair-Wise, Deformable Mirror, Image Plane-Based Diversity Electric Field Estimation for High Contrast Coronagraphy

    Science.gov (United States)

    Give'on, Amir; Kern, Brian D.; Shaklan, Stuart

    2011-01-01

    In this paper we describe the complex electric field reconstruction from image plane intensity measurements for high contrast coronagraphic imaging. A deformable mirror (DM) surface is modied with pairs of complementary shapes to create diversity in the image plane of the science camera where the intensity of the light is measured. Along with the Electric Field Conjugation correction algorithm, this estimation method has been used in various high contrast imaging testbeds to achieve the best contrasts to date both in narrow and in broad band light. We present the basic methodology of estimation in easy to follow list of steps, present results from HCIT and raise several open quations we are confronted with using this method.

  1. Stamping failure analysis of advanced high strength steel sheet based on non-uniform local deformation through thickness

    Science.gov (United States)

    Huang, Sheng; Zhao, Yixi; He, Chunfeng

    2013-12-01

    The phenomenon "Shear fracture" is often observed in the stretch-bending process of stamping over small radius with advanced high strength steels (AHSS). It occurs parallel to and near the die radius in the stretch-bending test. Since traditional Forming Limit Diagram (FLD) is unable to describe this type of failure, experimental and simulation works were constructed in this paper to investigate and predict the shear fracture. Fracture experiments were carried out through a stretch-bending test system, and failure mode was observed. There is no obviously thinning at the shear fracture surface. Further research shows that the initial crack of shear fracture occurs at the outer layer of specimen at die radius position. Finite element (FE) models were built for stretch-bending test with 3D element. The non-uniform local deformation through thickness corresponding to bending position was obtained and analyzed. Cockcroft & Latham fracture criterion is used. The outer layer of specimen at bending position reaches the critical fracture state firstly, which agrees well with experiments. Different fracture criteria are also compared and selected to determine this fracture. Results show that based on the non-uniform local deformation, the initial crack location of shear fracture at small radius can be effectively predicted by fracture criteria related to the maximum principle stress.

  2. Polymorphism of iron at high pressure: A 3D phase-field model for displacive transitions with finite elastoplastic deformations

    Science.gov (United States)

    Vattré, A.; Denoual, C.

    2016-07-01

    A thermodynamically consistent framework for combining nonlinear elastoplasticity and multivariant phase-field theory is formulated at large strains. In accordance with the Clausius-Duhem inequality, the Helmholtz free energy and time-dependent constitutive relations give rise to displacive driving forces for pressure-induced martensitic phase transitions in materials. Inelastic forces are obtained by using a representation of the energy landscape that involves the concept of reaction pathways with respect to the point group symmetry operations of crystal lattices. On the other hand, additional elastic forces are derived for the most general case of large strains and rotations, as well as nonlinear, anisotropic, and different elastic pressure-dependent properties of phases. The phase-field formalism coupled with finite elastoplastic deformations is implemented into a three-dimensional Lagrangian finite element approach and is applied to analyze the iron body-centered cubic (α-Fe) into hexagonal close-packed (ɛ-Fe) phase transitions under high hydrostatic compression. The simulations exhibit the major role played by the plastic deformation in the morphological and microstructure evolution processes. Due to the strong long-range elastic interactions between variants without plasticity, a forward α → ɛ transition is energetically unfavorable and remains incomplete. However, plastic dissipation releases considerably the stored strain energy, leading to the α ↔ ɛ ↔α‧ (forward and reverse) polymorphic phase transformations with an unexpected selection of variants.

  3. Measures for controlling large deformations of underground caverns under high in-situ stress condition-A case study of Jinping I hydropower station

    Institute of Scientific and Technical Information of China (English)

    Shengwu Song; Xuemin Feng; Chenggang Liao; Dewen Cai; Zhongxu Liu; Yunhao Yang

    2016-01-01

    The Jinping I hydropower station is a huge water conservancy project consisting of the highest concrete arch dam to date in the world and a highly complex and large underground powerhouse cavern. It is located on the right bank with extremely high in-situ stress and a few discontinuities observed in sur-rounding rock masses. The problems of rock mass deformation and failure result in considerable chal-lenges related to project design and construction and have raised a wide range of concerns in the fields of rock mechanics and engineering. During the excavation of underground caverns, high in-situ stress and relatively low rock mass strength in combination with large excavation dimensions lead to large deformation of the surrounding rock mass and support. Existing experiences in excavation and support cannot deal with the large deformation of rock mass effectively, and further studies are needed. In this paper, the geological conditions, layout of caverns, and design of excavation and support are first introduced, and then detailed analyses of deformation and failure characteristics of rocks are presented. Based on this, the mechanisms of deformation and failure are discussed, and the support adjustments for controlling rock large deformation and subsequent excavation procedures are proposed. Finally, the effectiveness of support and excavation adjustments to maintain the stability of the rock mass is verified. The measures for controlling the large deformation of surrounding rocks enrich the practical experiences related to the design and construction of large underground openings, and the construction of caverns in the Jinping I hydropower station provides a good case study of large-scale excavation in highly stressed ground with complex geological structures, as well as a reference case for research on rock mechanics. © 2016 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting by Elsevier B.V. This is an open access article

  4. Shape evolution at high spin states in Kr and Br isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Trivedi, T. [Department of Pure and Physics, Guru Ghasidas Vishwavidyalaya, Bilaspur-495009 (India); Palit, R.; Naik, Z.; Jain, H. C. [Tata Institute of Fundamental Research, Mumbai-400005 (India); Negi, D.; Kumar, R.; Singh, R. P.; Muralithar, S.; Pancholi, S. C.; Bhowmik, R. K. [Inter University Accelerator Centre, New Delhi-110067 (India); Yang, Y.-C.; Sun, Y. [Department of Physics, Shanghai Jiao Tong University, Shanghai 200240 (China); Sheikh, J. A. [Department of Physics, University of Kashmir, Srinagar 190 006 (India); Raja, M. K. [Department of Nuclear Physics, Andhra University, Visakhapatnam-530003 (India); Kumar, S. [Department of Physics and Astrophysics, University of Delhi, Delhi-110007 (India); Choudhury, D. [Department of Physics, IIT Roorkee, Roorkee-247667 (India); Jain, A. K.; Mehrotra, I. [Department of Physics, University of Allahabad, Allahabad-211001 (India)

    2014-08-14

    The high spin states in A = 75, Kr and Br isotopes have been populated via fusion-evaporation reaction at an incident beam energy of 90 MeV. The de-exciting γ-rays were detected utilizing the Indian National Gamma Array (INGA). Lifetime of these excited high spin states were determined by Doppler-shift attenuation method. Experimental results obtained from lifetime measurement are interpreted in the frame work of projected shell-model to get better insight into the evolution of collectivity. Comparison of the calculations of the model with transitional quadrupole moments Q{sub t} of the positive and negative parity bands firmly established their configurations.

  5. Comparison between diffraction contrast tomography and high-energy diffraction microscopy on a slightly deformed aluminium alloy.

    Science.gov (United States)

    Renversade, Loïc; Quey, Romain; Ludwig, Wolfgang; Menasche, David; Maddali, Siddharth; Suter, Robert M; Borbély, András

    2016-01-01

    The grain structure of an Al-0.3 wt%Mn alloy deformed to 1% strain was reconstructed using diffraction contrast tomography (DCT) and high-energy diffraction microscopy (HEDM). 14 equally spaced HEDM layers were acquired and their exact location within the DCT volume was determined using a generic algorithm minimizing a function of the local disorientations between the two data sets. The microstructures were then compared in terms of the mean crystal orientations and shapes of the grains. The comparison shows that DCT can detect subgrain boundaries with disorientations as low as 1° and that HEDM and DCT grain boundaries are on average 4 µm apart from each other. The results are important for studies targeting the determination of grain volume. For the case of a polycrystal with an average grain size of about 100 µm, a relative deviation of about ≤10% was found between the two techniques.

  6. Onset of T=0 Pairing and Deformations in High Spin States of the N=Z Nucleus $^{48}Cr$

    CERN Document Server

    Terasaki, J; Heenen, P H

    1998-01-01

    The yrast line of the N=Z nucleus 48Cr is studied up to high spins by means of the cranked Hartree-Fock-Bogoliubov method including the T=0 and T=1 isospin pairing channels. A Skyrme force is used in the mean-field channel together with a zero-range density-dependent interaction in the pairing channels. The extensions of the method needed to incorporate the neutron-proton pairing are summarized. The T=0 pairing correlations are found to play a decisive role for deformation properties and excitation energies above 16hbar which is the maximum spin that can be obtained in the f7/2 subshell.

  7. Comparison between diffraction contrast tomography and high-energy diffraction microscopy on a slightly deformed aluminium alloy

    Directory of Open Access Journals (Sweden)

    Loïc Renversade

    2016-01-01

    Full Text Available The grain structure of an Al–0.3 wt%Mn alloy deformed to 1% strain was reconstructed using diffraction contrast tomography (DCT and high-energy diffraction microscopy (HEDM. 14 equally spaced HEDM layers were acquired and their exact location within the DCT volume was determined using a generic algorithm minimizing a function of the local disorientations between the two data sets. The microstructures were then compared in terms of the mean crystal orientations and shapes of the grains. The comparison shows that DCT can detect subgrain boundaries with disorientations as low as 1° and that HEDM and DCT grain boundaries are on average 4 µm apart from each other. The results are important for studies targeting the determination of grain volume. For the case of a polycrystal with an average grain size of about 100 µm, a relative deviation of about ≤10% was found between the two techniques.

  8. Landslide deformation monitoring using point-like target offset tracking with multi-mode high-resolution TerraSAR-X data

    Science.gov (United States)

    Shi, Xuguo; Zhang, Lu; Balz, Timo; Liao, Mingsheng

    2015-07-01

    Many landslides in the Three Georges area have shown active deformations associated with water level fluctuations since the full operation of the Three Georges Dam. Such active deformations of landslide bodies need to be closely monitored for disaster prevention and warning. One way to do this is to employ SAR pixel offset tracking, a powerful technique that can be used for measuring two-dimensional large displacements. As an improvement of the original pixel offset tracking technique, the point-like target (PT) offset tracking method focuses on stable point-like targets and thus can obtain more reliable measurements. In this paper, the PT offset tracking method is employed to investigate historical evolution of the Shuping landslide, using time series TerraSAR-X data acquired in both Stripmap (SM) and High-resolution Spotlight (HS) modes. Artificial corner reflectors (CR) installed at/near the landslide are identified as PTs and used to analyze the spatial-temporal pattern of landslide deformations. Results showed that the maximum accumulative deformation of the Shuping landslide reached more than 1.5 m over a time span of two years. A correlation analysis between the deformation trends and the fluctuation of reservoir water level indicated that most deformations of the landslide happened during the water level declining period.

  9. Effects of vitamin E blending on plastic deformation mechanisms of highly crosslinked ultrahigh molecular weight polyethylene (HXL-UHMWPE) in total hip arthroplasty.

    Science.gov (United States)

    Takahashi, Yasuhito; Yamamoto, Kengo; Pezzotti, Giuseppe

    2015-03-01

    The molecular mobility and crystalline texture development in highly crosslinked ultrahigh molecular weight polyethylene (HXL-UHMWPE) blended with antioxidant vitamin E (VE, dl-α-tocopherol) were studied via uniaxial compression at room temperature by means of confocal/polarized Raman spectroscopy. The results were compared to morphological analyses under the same compression conditions performed on HXL-UHMWPE prepared in exactly the same way but blending VE into the polyethylene resin (VE-free HXL-UHMWPE). These comparative analyses allow us to evaluate the physical role of VE in morphological alterations of HXL-UHMWPE induced by compression deformation, which can greatly affect its micromechanical behavior. Molecular rearrangement and phase transitions in crystalline and non-crystalline phase, i.e. amorphous and intermediate (third) phase, were found to be part of a reconstruction process after plastic deformation in the samples. Although VE-blended HXL-UHMWPE exhibited more pronounced molecular mobility, as evidenced by its significant deformation-induced texturing, crystallinity change was totally inhibited by the presence of VE during deformation. On the other hand, amorphous-to-intermediate phase transition was confirmed. VE-free HXL-UHMWPE also presented significant crystallization after deformation, but its surface texture evolution occurred to a much lesser extent. This study suggests that the addition of VE induced earlier activation of compression deformation modes in crystalline and non-crystalline phases (e.g. chain slip, interlamellar shear and rotation) due to an increase in polyethylene chain mobility.

  10. High-frame-rate deformation imaging in two dimensions using continuous speckle-feature tracking

    DEFF Research Database (Denmark)

    Andersen, Martin Vandborg; Moore, Cooper; Arges, Kristine;

    2016-01-01

    The study describes a novel algorithm for deriving myocardial strain from an entire cardiac cycle using high-frame-rate ultrasound images. Validation of the tracking algorithm was conducted in vitro prior to the application to patient images. High-frame-rate ultrasound images were acquired in vivo...... from 10 patients, and strain curves were derived in six myocardial regions around the left ventricle from the apical four-chamber view. Strain curves derived from high-frame-rate images had a higher frequency content than those derived using conventional methods, reflecting improved temporal sampling....

  11. Highly variable coastal deformation in the 2016 MW7.8 Kaikōura earthquake reflects rupture complexity along a transpressional plate boundary

    Science.gov (United States)

    Clark, K. J.; Nissen, E. K.; Howarth, J. D.; Hamling, I. J.; Mountjoy, J. J.; Ries, W. F.; Jones, K.; Goldstien, S.; Cochran, U. A.; Villamor, P.; Hreinsdóttir, S.; Litchfield, N. J.; Mueller, C.; Berryman, K. R.; Strong, D. T.

    2017-09-01

    Coseismic coastal deformation is often used to understand slip on offshore faults in large earthquakes but in the 2016 MW 7.8 Kaikōura earthquake multiple faults ruptured across and sub-parallel to the coastline. Along ∼110 km of coastline, a rich dataset of coastal deformation comprising airborne lidar differencing, field surveying and satellite geodesy reveals highly variable vertical displacements, ranging from -2.5 to 6.5 m. These inform a refined slip model for the Kaikōura earthquake which incorporates changes to the slip on offshore faults and inclusion of an offshore reverse crustal fault that accounts for broad, low-amplitude uplift centered on Kaikōura Peninsula. The exceptional detail afforded by differential lidar and the high variability in coastal deformation combine to form the highest-resolution and most complex record of coseismic coastal deformation yet documented. This should prompt reassessment of coastal paleoseismic records that may not have considered multi-fault ruptures and high complexity deformation fields.

  12. On The Creep Behavior and Deformation Mechanisms Found in an Advanced Polycrystalline Nickel-Base Superalloy at High Temperatures

    Science.gov (United States)

    Deutchman, Hallee Zox

    Polycrystalline Ni-base superalloys are used as turbine disks in the hot section in jet engines, placing them in a high temperature and stress environment. As operating temperatures increase in search of better fuel efficiency, it becomes important to understand how these higher temperatures are affecting mechanical behavior and active deformation mechanisms in the substructure. Not only are operating temperatures increasing, but there is a drive to design next generation alloys in shorter time periods using predictive modeling capabilities. This dissertation focuses on mechanical behavior and active deformation mechanisms found in two different advanced polycrystalline alloy systems, information which will then be used to build advanced predictive models to design the next generation of alloys. The first part of this dissertation discusses the creep behavior and identifying active deformation mechanisms in an advanced polycrystalline Ni-based superalloy (ME3) that is currently in operation, but at higher temperatures and stresses than are experienced in current engines. Monotonic creep tests were run at 700°C and between 655-793MPa at 34MPa increments, on two microstructures (called M1 and M2) produced by different heat treatments. All tests were crept to 0.5% plastic strain. Transient temperature and transient stress tests were used determine activation energy and stress exponents of the M1 microstructure. Constant strain rate tests (at 10-4s-1) were performed on both microstructures as well. Following creep testing, both M1 and M2 microstructures were fully characterized using Scanning Electron Microscopy (SEM) for basic microstructure information, and Scanning Transmission Electron Microscopy (STEM) to determine active deformation mechanism. It was found that in the M1 microstructure, reorder mediated activity (such as discontinuous faulting and microtwinning) is dominant at low stresses (655-724 MPa). Dislocations in the gamma matrix, and overall planar

  13. Highly Reflecting, Broadband Deformable Membrane Mirror for Wavefront Control Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase I STTR project will develop a highly reflecting, broadband, radiation resistant, low-stress and lightweight, membrane integrated into an electrostatically...

  14. Mechanical Properties and Fractographic Analysis of High Manganese Steels After Dynamic Deformation Tests

    Directory of Open Access Journals (Sweden)

    Jabłońska M.B.

    2014-10-01

    Full Text Available Since few years many research centres conducting research on the development of high-manganese steels for manufacturing of parts for automotive and railway industry. Some of these steels belong to the group of AHS possessing together with high strength a great plastic elongation, and an ideal uniform work hardening behavior. The article presents the dynamic mechanical properties of two types of high manganese austenitic steel with using a flywheel machine at room temperature with strain rates between 5×102÷3.5×103s?–1. It was found that the both studied steels exhibit a high sensitivity Rm to the strain rate. With increasing the strain rate from 5×102 to 3.5×103s?–1 the hardening dominates the process. The fracture analysis indicate that after dynamic test both steel is characterized by ductile fracture surfaces which indicate good plasticity of investigated steels.

  15. Monotonic and Cyclic Bond Behavior of Deformed CFRP Bars in High Strength Concrete

    OpenAIRE

    2016-01-01

    Composite reinforcing bars (rebars) that are used in concrete members with high performance (strength and durability) properties could have beneficial effects on the behavior of these members. This is especially vital when a building is constructed in an aggressive environment, for instance a corrosive environment. Although tension capacity/weight (or volume) ratios in composite rebars (carbon fiber reinforced polymer (CFRP), glass fiber reinforced polymer (GFRP), etc.) are very high when com...

  16. Ultra-high aspect ratio replaceable AFM tips using deformation-suppressed focused ion beam milling

    DEFF Research Database (Denmark)

    Savenko, Alexey; Yildiz, Izzet; Petersen, Dirch Hjorth;

    2013-01-01

    Fabrication of ultra-high aspect ratio exchangeable and customizable tips for atomic force microscopy (AFM) using lateral focused ion beam (FIB) milling is presented. While on-axis FIB milling does allow high aspect ratio (HAR) AFM tips to be defined, lateral milling gives far better flexibility...... FIB milling strategies for obtaining sharper tips are discussed. Finally, assembly of the HAR tips on a custom-designed probe as well as the first AFM scanning is shown....

  17. Decay out of the yrast and excited highly-deformed bands in the even-even nucleus {sup 134}Nd

    Energy Technology Data Exchange (ETDEWEB)

    Petrache, C.M.; Bazzacco, D.; Lunardi, S. [Sezione di Padova (Italy)] [and others

    1996-12-31

    The resolving power achieved by the new generation of {gamma}-ray detector arrays allows now to observe transitions with intensities of the order of {approximately}10{sup {minus}3} of the population of the final residual nucleus, making therefore feasible the study of the very weakly populated excited bands built on the superdeformed (SD) minimum or of the decay out of the SD bands. As a matter of fact, numerous excited SD bands have been observed in the different regions of superdeformation, which led to a deeper understanding of the single-particle excitation in the second minimum. The first experimental breakthrough in the study of the decay out process has been achieved in the odd-even {sup 133,135}Nd nuclei of the A=130 mass region. There, the observation of the discrete linking transitions has been favored by the relatively higher intensity of the highly-deformed (HD) bands ({approximately}10%), as well as by the small excitation energy with respect to the yrast line in the decay-out region ({approximately}1 MeV). No discrete linking transitions have been so far observed in the A=80, 150 mass regions. The present results suggest that the decay out of the HD bands in {sup 134}Nd is triggered by the crossing with the N=4 [402]5/2{sup +} Nilsson orbital, that has a smaller deformation than the corresponding N=6 intruder configuration. The crossing favours the mixing with the ND rotational bands strongly enhancing the decay-out process and weakening the in-band transition strength. The HD band becomes fragmented and looses part of its character. The intensity of the decay-out transitions increases when the spin of the HD state decreases, indicating enhanced ND amplitude in the wavefunction when going down the band. Lifetime measurements of the HD bands are crucial to further elucidate the decay-out process.

  18. High-Temperature Deformation Constitutive Law for Dissimilar Weld Residual Stress Modeling: Effect of Thermal Load on Strain Hardening

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Xinghua [ORNL; Wang, Yanli [ORNL; Crooker, Paul [Electric Power Research Institute (EPRI); Feng, Zhili [ORNL

    2015-01-01

    Weld residual stress is one of the primary driving forces for primary water stress corrosion cracking in dissimilar metal welds (DMWs). To mitigate tensile residual stress in DMWs, it is critical to understand residual stress distribution by modeling techniques. Recent studies have shown that weld residual stress prediction using today s DMW residual stress models strongly depends on the strain-hardening constitutive model chosen. The commonly used strain-hardening models (isotropic, kinematic, and mixed) are all time-independent and inadequate to account for the time-dependent (viscous) plastic deformation at the elevated temperatures experienced during welding. For materials with profound strain-hardening, such as stainless steels and nickel-based alloys that are widely used in nuclear reactor and piping systems, the equivalent plastic strain the determinate factor of the flow stress can be highly dependent on the recovery and recrystallization processes. These processes are in turn a strong function of temperature, time, and deformation rate. Recently, the authors proposed a new temperature- and time-dependent strain-hardening constitutive model: the dynamic strain-hardening constitutive model. The application of such a model has resulted in improved weld residual stress prediction compared to the residual stress measurement results from the contour and deep-hole drilling methods. In this study, the dynamic strain-hardening behavior of Type 304 stainless steel and Alloy 82 used in pressure vessel nozzle DMWs is experimentally determined. The kinetics of the recovery and recrystallization of flow stress are derived from experiments, resulting in a semi-empirical equation as a function of pre-strain, time, and temperature that can be used for weld residual stress modeling. The method used in this work also provides an approach to study the kinetics of recovery and recrystallization of other materials with significant strain-hardening.

  19. Macro- and microscopic mechanical behaviour of flow of coal samples experimentally deformed at high temperatures and pressures

    Institute of Scientific and Technical Information of China (English)

    LIU Junlai; YANG Guang; MA Rui

    2005-01-01

    Coal samples from Qinshui Basin, Shanxi,China are experimentally deformed at temperatures and confining pressures of 200-500 ℃ and 200-500 Mpa,strain rate of 0.5×10-5/s and total strain of 10%. The vitrinite reflectance of the coal samples varies from 3.04 to 1.79. It is shown that the strengths of the deformed samples change obviously with coeval increasing temperatures and pressures (T/P). At the experimental range of T/P, the effects of increasing temperature predominate over that of increasing pressure. Microstructural analysis indicates a brittle to ductile transition under experimental T/P conditions from 200 to 300℃, and 200 to 300Mpa. Brittle deformation microstructures include macroscopic fracture zones and penetrative fracture associations. Elongation, undulose or irregular extinction, deformation lamellae and dynamic recrystallization of grains are the main ductile deformation microstructures.The variation of deformation mechanisms of the experimentally deformed coal samples is related to both the components of coals and T/P conditions. At low T/P, fractures occur in both inertinite and vitrinite of the samples. At higher T/P,crystalline plastic deformations are observed in the inertinite only.

  20. Contracture deformity

    Science.gov (United States)

    Deformity - contracture ... Contracture can be caused by any of the following: Brain and nervous system disorders, such as cerebral ... Follow your health care provider's instructions for treating contracture at home. Treatments may include: Doing exercises and ...

  1. Quantification of the microstructures of high purity nickel subjected to dynamic plastic deformation

    DEFF Research Database (Denmark)

    Luo, Z.P.; Zhang, H.W.; Hansen, Niels

    2012-01-01

    and the misorientation angle across dislocation boundaries and high angle boundaries. These boundaries subdivide the structure on a finer and finer scale towards saturation at the highest strain. The structural evolution follows a hierarchical pattern from the formation of cells and cell blocks to a characteristic...

  2. Deformation and degradation of polymers in ultra-high-pressure liquid chromatography

    NARCIS (Netherlands)

    Uliyanchenko, E.; van der Wal, S.; Schoenmakers, P.J.

    2011-01-01

    Ultra-high-pressure liquid chromatography (UHPLC) using columns packed with sub-2 μm particles has great potential for separations of many types of complex samples, including polymers. However, the application of UHPLC for the analysis of polymers meets some fundamental obstacles. Small particles an

  3. Towards high velocity deformation characterisation of metals and composites using Digital Image Correlation

    DEFF Research Database (Denmark)

    Eriksen, Rasmus Normann Wilken; Berggreen, Christian; Boyd, S.W

    2010-01-01

    testing in the strain rate regime from 1 – 500 ε/s. The range is much lower than that experienced under ballistic, shock or impact loads, nevertheless it is a useful starting point for the application of optical techniques. The present study examines the possibility of using high speed cameras to capture...

  4. Extremely deformable structures

    CERN Document Server

    2015-01-01

    Recently, a new research stimulus has derived from the observation that soft structures, such as biological systems, but also rubber and gel, may work in a post critical regime, where elastic elements are subject to extreme deformations, though still exhibiting excellent mechanical performances. This is the realm of ‘extreme mechanics’, to which this book is addressed. The possibility of exploiting highly deformable structures opens new and unexpected technological possibilities. In particular, the challenge is the design of deformable and bi-stable mechanisms which can reach superior mechanical performances and can have a strong impact on several high-tech applications, including stretchable electronics, nanotube serpentines, deployable structures for aerospace engineering, cable deployment in the ocean, but also sensors and flexible actuators and vibration absorbers. Readers are introduced to a variety of interrelated topics involving the mechanics of extremely deformable structures, with emphasis on ...

  5. In situ synchrotron high-energy X-ray diffraction study of microscopic deformation behavior of a hard-soft dual phase composite containing phase transforming matrix

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Junsong; Hao, Shijie; Jiang, Daqiang; Huan, Yong; Cui, Lishan; Liu, Yinong; Yang, Hong; Ren, Yang

    2017-05-01

    This study explored a novel intermetallic composite design concept based on the principle of lattice strain matching enabled by the collective atomic load transfer. It investigated the hard-soft microscopic deformation behavior of a Ti3Sn/TiNi eutectic hard-soft dual phase composite by means of in situ synchrotron high-energy X-ray diffraction (HE-XRD) during compression. The composite provides a unique micromechanical system with distinctive deformation behaviors and mechanisms from the two components, with the soft TiNi matrix deforming in full compliance via martensite variant reorientation and the hard Ti3Sn lamellae deforming predominantly by rigid body rotation, producing a crystallographic texture for the TiNi matrix and a preferred alignment for the Ti3Sn lamellae. HE-XRD reveals continued martensite variant reorientation during plastic deformation well beyond the stress plateau of TiNi. The hard and brittle Ti3Sn is also found to produce an exceptionally large elastic strain of 1.95% in the composite. This is attributed to the effect of lattice strain matching between the transformation lattice distortion of the TiNi matrix and the elastic strain of Ti3Sn lamellae. With such unique micromechanic characteristics, the composite exhibits high strength and large ductility.

  6. Influence of high deformation on the microstructure of low-carbon steel

    Institute of Scientific and Technical Information of China (English)

    Florin Popa; Ionel Chicina; Dan Frunz; Ioan Nicodim; Dorel Banabic

    2014-01-01

    Low-carbon steel sheets DC04 used in the automotive industry were subjected to cold rolling for thickness reduction from 20%to 89%. The desired thickness was achieved by successive reductions using a rolling mill. The influence of thickness reduction on the micro-structure was studied by scanning electron microscopy. Microstructure evolution was characterized by the distortion of grains and the occur-rence of the oriented grain structure for high cold work. A mechanism of grain restructuring for high cold work was described. The occur-rence of voids was discussed in relation with cold work. The evolution of voids at the grain boundaries and inside the grains was also consid-ered. To characterize the grain size, the Feret diameter was measured and the grain size distribution versus cold work was discussed. The chemical homogeneity of the sample was also analyzed.

  7. A Model for High-Strain-Rate Deformation of Uranium-Niobium Alloys

    Energy Technology Data Exchange (ETDEWEB)

    F.L.Addessio; Q.H.Zuo; T.A.Mason; L.C.Brinson

    2003-05-01

    A thermodynamic approach is used to develop a framework for modeling uranium-niobium alloys under the conditions of high strain rate. Using this framework, a three-dimensional phenomenological model, which includes nonlinear elasticity (equation of state), phase transformation, crystal reorientation, rate-dependent plasticity, and porosity growth is presented. An implicit numerical technique is used to solve the evolution equations for the material state. Comparisons are made between the model and data for low-strain-rate loading and unloading as well as for heating and cooling experiments. Comparisons of the model and data also are made for low- and high-strain-rate uniaxial stress and uniaxial strain experiments. A uranium-6 weight percent niobium alloy is used in the comparisons of model and experiment.

  8. Monotonic and Cyclic Bond Behavior of Deformed CFRP Bars in High Strength Concrete

    Directory of Open Access Journals (Sweden)

    T. Tibet Akbas

    2016-05-01

    Full Text Available Composite reinforcing bars (rebars that are used in concrete members with high performance (strength and durability properties could have beneficial effects on the behavior of these members. This is especially vital when a building is constructed in an aggressive environment, for instance a corrosive environment. Although tension capacity/weight (or volume ratios in composite rebars (carbon fiber reinforced polymer (CFRP, glass fiber reinforced polymer (GFRP, etc. are very high when compared to steel rebars, major weaknesses in concrete members reinforced with these composite rebars may be the potential consequences of relatively poor bonding capacity. This may even be more crucial when the member is subjected to cyclic loading. Although monotonic bond tests are available in the literature, only limited experimental studies exist on bond characteristics under cyclic loading conditions. In order to fill this gap and propose preliminary design recommendations, 10 specimens of 10-mm-diameter ribbed CFRP rebars embedded in specially designed high strength concrete (f’c = 70 MPa blocks were subjected to monotonic and cyclic pullout tests. The experimental results showed that cyclically loaded CFRP rebars had less bond strength than those companion specimens loaded monotonically.

  9. Creep deformation of grain boundary in a highly crystalline SiC fibre.

    Science.gov (United States)

    Shibayama, Tamaki; Yoshida, Yutaka; Yano, Yasuhide; Takahashi, Heishichiro

    2003-01-01

    Silicon carbide (SiC) matrix composites reinforced by SiC fibres (SiC/SiC composites) are currently being considered as alternative materials in high Ni alloys for high-temperature applications, such as aerospace components, gas-turbine energy-conversion systems and nuclear fusion reactors, because of their high specific strength and fracture toughness at elevated temperatures compared with monolithic SiC ceramics. It is important to evaluate the creep properties of SiC fibres under tensile loading in order to determine their usefulness as structural components. However, it would be hard to evaluate creep properties by monoaxial tensile properties when we have little knowledge on the microstructure of crept specimens, especially at the grain boundary. Recently, a simple fibre bend stress relaxation (BSR) test was introduced by Morscher and DiCarlo to address this problem. Interpretation of the fracture mechanism at the grain boundary is also essential to allow improvement of the mechanical properties. In this paper, effects of stress applied by BSR test on microstructural evolution in advanced SiC fibres, such as Tyranno-SA including small amounts of Al, are described and discussed along with the results of microstructure analysis on an atomic scale by using advanced microscopy.

  10. Magmatism and Eurekan deformation in the High Arctic Large Igneous Province

    DEFF Research Database (Denmark)

    Tegner, Christian; Storey, Michael; Holm, Paul Martin

    2011-01-01

    in the Northeast Atlantic resulted in spreading and volcanism (61– 25 Ma) on both sides of Greenland, pushing Greenland northwards relative to North America. The tectonic setting in the High Arctic thus changed from extensional to compressional and volcanic activity was terminated. Evaluation of plate kinematic...... perthite feldspars and coeval resetting of Rb–Sr isotopes by hydrothermal fluids provide further support for thermal overprinting. This thermal event is interpreted as a result of compressional tectonism of the Kap Cannon Thrust Zone in which older Palaeozoic metasediments were thrusted northwards over...

  11. Investigation of Structure, Properties and Deformation Mechanisms of Elevated Temperature Al Alloys with High Specific Properties

    Science.gov (United States)

    2007-11-02

    stage – the porous filter from material with size pores amount 1 µm. Aluminum- oxide -coating AW, and Zirconium -coating ZR-M are used for coating of...5 we used a heat resistant aluminum alloy reinforced by quasicrystalline nanosize particles, which was elaborated in frames of Task 3 and 6, as the...formation of a composite that consists of an amorphous matrix with embedded nanosize (5-10 nm) α-Al particles and has a high hardness HV = 3.5 GPa is

  12. Deformation of Ordered Mesoporous Silica Structures on Exposure to High Temperatures

    Directory of Open Access Journals (Sweden)

    John B. Lowe

    2014-01-01

    Full Text Available Ordered mesoporous silica materials are of interest for a wide range of applications. In many of these, elevated temperatures are used either in the preparation of the material or during its use. Therefore, an understanding of the effect of high temperature treatments on these materials is desirable. In this work, a detailed structural study is performed on silicas with three representative pore structures: a 2-D hexagonal pore arrangement (SBA-15, a continuous 3D cubic bimodal pore structure (KIT-6, and a 3D large cage pore structure (FDU-12. Each silica is studied as prepared and after treatment at a series of temperatures between 300 and 900°C. Pore structures are imaged using Transmission Electron Microscopy. This technique is used in conjunction with Small-Angle X-ray Diffraction, gas physisorption, and 29Si solid state Nuclear Magnetic Resonance. Using these techniques, the pore size distributions, the unit cell dimensions of the mesoporous structures, and the relative occupancy of the distinct chemical environments of Si within them are cross correlated for the three silicas and their evolution with treatment temperature is elucidated. The physical and chemical properties before, during, and after collapse of these structures at high temperatures are described as are the differences in behavior between the three silica structures.

  13. A viable circulating tumor cell isolation device with high retrieval efficiency using a reversibly deformable membrane barrier

    Science.gov (United States)

    Kim, Yoonji; Bu, Jiyoon; Cho, Young-Ho; Son, Il Tae; Kang, Sung-Bum

    2017-02-01

    Circulating tumor cells (CTCs) contain prognostic information of the tumor, since they shed from the primary tumor and invade into the bloodstream. Therefore, the viable isolation is necessary for a consequent analysis of CTCs. Here, we present a device for the viable isolation and efficient retrieval of CTCs using slanted slot filters, formed by a reversibly deformable membrane barrier. Conventional filters have difficulties in retrieving captured cells, since they easily clog the slots. Moreover, large stress concentration at the sharp edges of squared slots, causes cell lysis. In contrast, the present device shows over 94% of high retrieval efficiency, since the slots can be opened simply by relieving the pressure. Furthermore, the inflated membrane barrier naturally forms the slanted slots, thus reducing the cell damage. By using cancer cell lines, we verified that the present device successfully isolate targeted cells, even at an extremely low concentrations (~10 cells/0.1 ml). In the clinical study, 85.7% of patients initially showed CTC positive while the numbers generally decreased after the surgery. We have also proved that the number of CTCs were highly correlated with tumour invasiveness. Therefore, the present device has potential for use in cancer diagnosis, surgical validation, and invasiveness analysis.

  14. Simultaneous X-ray diffraction and phase-contrast imaging for investigating material deformation mechanisms during high-rate loading.

    Science.gov (United States)

    Hudspeth, M; Sun, T; Parab, N; Guo, Z; Fezzaa, K; Luo, S; Chen, W

    2015-01-01

    Using a high-speed camera and an intensified charge-coupled device (ICCD), a simultaneous X-ray imaging and diffraction technique has been developed for studying dynamic material behaviors during high-rate tensile loading. A Kolsky tension bar has been used to pull samples at 1000 s(-1) and 5000 s(-1) strain-rates for super-elastic equiatomic NiTi and 1100-O series aluminium, respectively. By altering the ICCD gating time, temporal resolutions of 100 ps and 3.37 µs have been achieved in capturing the diffraction patterns of interest, thus equating to single-pulse and 22-pulse X-ray exposure. Furthermore, the sample through-thickness deformation process has been simultaneously imaged via phase-contrast imaging. It is also shown that adequate signal-to-noise ratios are achieved for the detected white-beam diffraction patterns, thereby allowing sufficient information to perform quantitative data analysis diffraction via in-house software (WBXRD_GUI). Of current interest is the ability to evaluate crystal d-spacing, texture evolution and material phase transitions, all of which will be established from experiments performed at the aforementioned elevated strain-rates.

  15. Influence of cold deformation and annealing on hydrogen embrittlement of cold hardening bainitic steel for high strength bolts

    Energy Technology Data Exchange (ETDEWEB)

    Hui, Weijun, E-mail: wjhui@bjtu.edu.cn [School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Zhang, Yongjian; Zhao, Xiaoli; Shao, Chengwei [School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Wang, Kaizhong; Sun, Wei; Yu, Tongren [Technical Center, Maanshan Iron & Steel Co., Ltd., Maanshan 243002, Anhui (China)

    2016-04-26

    The influence of cold drawing and annealing on hydrogen embrittlement (HE) of newly developed cold hardening bainitic steel was investigated by using slow strain rate testing (SSRT) and thermal desorption spectrometry (TDS), for ensuring safety performance of 10.9 class high strength bolts made of this kind of steel against HE under service environments. Hydrogen was introduced into the specimen by electrochemical charging. TDS analysis shows that the hydrogen-charged cold drawn specimen exhibits an additional low-temperature hydrogen desorption peak besides the original high-temperature desorption peak of the as-rolled specimen, causing remarkable increase of absorbed hydrogen content. It is found that cold drawing significantly enhances the susceptibility to HE, which is mainly attributed to remarkable increase of diffusible hydrogen absorption, the occurrence of strain-induced martensite as well as the increase of strength level. Annealing after cold deformation is an effective way to improve HE resistance and this improvement strongly depends on annealing temperature, i.e. HE susceptibility decreases slightly with increasing annealing temperature up to 200 °C and then decreases significantly with further increasing annealing temperature. This phenomenon is explained by the release of hydrogen, the recovery of cold worked microstructure and the decrease of strength with increasing annealing temperature.

  16. High-resolution spatiotemporal strain mapping reveals non-uniform deformation in micropatterned elastomers

    Science.gov (United States)

    Aksoy, B.; Rehman, A.; Bayraktar, H.; Alaca, B. E.

    2017-04-01

    Micropatterns are generated on a vast selection of polymeric substrates for various applications ranging from stretchable electronics to cellular mechanobiological systems. When these patterned substrates are exposed to external loading, strain field is primarily affected by the presence of microfabricated structures and similarly by fabrication-related defects. The capturing of such nonhomogeneous strain fields is of utmost importance in cases where study of the mechanical behavior with a high spatial resolution is necessary. Image-based non-contact strain measurement techniques are favorable and have recently been extended to scanning tunneling microscope and scanning electron microscope images for the characterization of mechanical properties of metallic materials, e.g. steel and aluminum, at the microscale. A similar real-time analysis of strain heterogeneity in elastomers is yet to be achieved during the entire loading sequence. The available measurement methods for polymeric materials mostly depend on cross-head displacement or precalibrated strain values. Thus, they suffer either from the lack of any real-time analysis, spatiotemporal distribution or high resolution in addition to a combination of these factors. In this work, these challenges are addressed by integrating a tensile stretcher with an inverted optical microscope and developing a subpixel particle tracking algorithm. As a proof of concept, the patterns with a critical dimension of 200 µm are generated on polydimethylsiloxane substrates and strain distribution in the vicinity of the patterns is captured with a high spatiotemporal resolution. In the field of strain measurement, there is always a tradeoff between minimum measurable strain value and spatial resolution. Current noncontact techniques on elastomers can deliver a strain resolution of 0.001% over a minimum length of 5 cm. More importantly, inhomogeneities within this quite large region cannot be captured. The proposed technique can

  17. Topographic deformation patterns of knee cartilage after exercises with high knee flexion: an in vivo 3D MRI study using voxel-based analysis at 3T

    Energy Technology Data Exchange (ETDEWEB)

    Horng, Annie; Stockinger, M.; Notohamiprodjo, M. [Ludwig-Maximilians-University Hospital Munich, Institute for Clinical Radiology, Munich (Germany); Raya, J.G. [New York University Langone Medical Center, Center for Biomedical Imaging, New York, NY (United States); Pietschmann, M. [Ludwig-Maximilians-University Hospital Munich, Department of Orthopedic Surgery, Munich (Germany); Hoehne-Hueckstaedt, U.; Glitsch, U.; Ellegast, R. [Institute for Occupational Safety and Health of the German Social Accident Insurance (IFA), Sankt Augustin (Germany); Hering, K.G. [Miner' s Hospital, Department of Diagnostic Radiology, Dortmund (Germany); Glaser, C. [Ludwig-Maximilians-University Hospital Munich, Institute for Clinical Radiology, Munich (Germany); RZM Zentrum, Munich (Germany)

    2015-06-01

    To implement a novel voxel-based technique to identify statistically significant local cartilage deformation and analyze in-vivo topographic knee cartilage deformation patterns using a voxel-based thickness map approach for high-flexion postures. Sagittal 3T 3D-T1w-FLASH-WE-sequences of 10 healthy knees were acquired before and immediately after loading (kneeling/squatting/heel sitting/knee bends). After cartilage segmentation, 3D-reconstruction and 3D-registration, colour-coded deformation maps were generated by voxel-based subtraction of loaded from unloaded datasets to visualize cartilage thickness changes in all knee compartments. Compression areas were found bifocal at the peripheral medial/caudolateral patella, both posterior femoral condyles and both anterior/central tibiae. Local cartilage thickening were found adjacent to the compression areas. Significant local strain ranged from +13 to -15 %. Changes were most pronounced after squatting, least after knee bends. Shape and location of deformation areas varied slightly with the loading paradigm, but followed a similar pattern consistent between different individuals. Voxel-based deformation maps identify individual in-vivo load-specific and posture-associated strain distribution in the articular cartilage. The data facilitate understanding individual knee loading properties and contribute to improve biomechanical 3 models. They lay a base to investigate the relationship between cartilage degeneration patterns in common osteoarthritis and areas at risk of cartilage wear due to mechanical loading in work-related activities. (orig.)

  18. Glacio-tectonic thrust and deformation structures in the Vejle Fjord, Denmark revealed by high-resolution subbottom-profile data

    DEFF Research Database (Denmark)

    Andresen, Katrine Juul; Boldreel, Lars Ole; Wahlgreen, Katrine Bak;

    Surface geomorphological features and partial cliff exposures up till now represent the predominant source of information of glaciation related deformation in Denmark. In this study we apply high-resolution marine reflection seismic data from the Vejle Fjord area, supported by gravity and Rumohr...... of the fjord. To the north, the deformation is expressed by complex internal reflection patterns within discrete sedimentary units including faults and smaller thrust-structures and associated small-scale folding. Channel incisions and clear reflection relations (i.e. truncations, onlaps and downlaps) reveal...... indicating severe deformation which most likely reflects ice progression from a southerly direction; for instance by the Young Baltic Ice Stream c. 19-17 ka. A thick and undisturbed build-out sequence can be observed to the north and in front of the thrust-belt probably representing meltwater sedimentation...

  19. High-resolution in vivo imaging of the cross-sectional deformations of contracting embryonic heart loops using optical coherence tomography

    DEFF Research Database (Denmark)

    Männer, J.; Thrane, Lars; Norozi, K.

    2008-01-01

    tubes as concentric narrowing and widening of tubes of circular cross-section. We have visualized the cross-sectional deformations of contracting embryonic hearts in chick embryos (HH-stages 9-17) using real-time high-resolution optical coherence tomography. Cardiac contractions are detected from HH...

  20. Low-Temperature Nitriding of Deformed Austenitic Stainless Steels with Various Nitrogen Contents Obtained by Prior High-Temperature Solution Nitriding

    DEFF Research Database (Denmark)

    Bottoli, Federico; Winther, Grethe; Christiansen, Thomas Lundin;

    2016-01-01

    investigated. Both hardness and yield stress increase and the alloys remain ductile. In addition, strain-induced transformation of austenite to martensite is suppressed, which is beneficial for subsequent low-temperature nitriding of the surface of deformed alloys. The combination of high- and low...

  1. Characterizing high-temperature deformation of internally heated nuclear fuel element simulators

    Energy Technology Data Exchange (ETDEWEB)

    Belov, A.I.; Fong, R.W.L.; Leitch, B.W.; Nitheanandan, T.; Williams, A., E-mail: alexander.belov@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada)

    2016-06-15

    The sag behaviour of a simulated nuclear fuel element during high-temperature transients has been investigated in an experiment utilizing an internal indirect heating method. The major motivation of the experiment was to improve understanding of the dominant mechanisms underlying the element thermo-mechanical response under loss-of-coolant accident conditions and to obtain accurate experimental data to support development of 3-D computational fuel element models. The experiment was conducted using an electrically heated CANDU fuel element simulator. Three consecutive thermal cycles with peak temperatures up to ≈1000 {sup o}C were applied to the element. The element sag deflections and sheath temperatures were measured. On heating up to 600 {sup o}C, only minor lateral deflections of the element were observed. Further heating to above 700 {sup o}C resulted in an element multi-rate creep and significant permanent bow. Post-test visual and X-ray examinations revealed a pronounced necking of the sheath at the pellet-to-pellet interface locations. A wall thickness reduction was detected in the necked region that is interpreted as a sheath longitudinal strain localization effect. The sheath cross-sectioning showed signs of a 'hard' pellet-cladding interaction due to the applied cycles. A 3-D model of the experiment was generated using the ANSYS finite element code. As a fully coupled thermal mechanical simulation is computationally expensive, it was deemed sufficient to use the measured sheath temperatures as a boundary condition, and thus an uncoupled mechanical simulation only was conducted. The ANSYS simulation results match the experiment sag observations well up to the point at which the fuel element started cooling down. (author)

  2. 高钢级管线钢变形抗力模型%Research on mathematical model for the deformation resistance of high strength pipeline steel

    Institute of Scientific and Technical Information of China (English)

    林鹏飞; 胡水平; 余伟; 宋晓波

    2011-01-01

    The test study for plastic deformation resistance of two kinds of high strength pipeline steels with different components was engaged in single pass compression test by Gleeble-3500. The influence of deforming temperature, deforming velocity and deforming degree on deformation resistance were analyzed and a new model of deformation resistance suitable for X70 and X80 steels was established. Through multiple linear regression analysis, this model proved to have good curve fitting characteristics and relatively high precision. The model has been successfully used in rolling production with relative error of rolling force less than eleven percent%利用Gleeble-3500热模拟试验机,对两种不同成分的高钢级管线钢进行单道次压缩实验的塑性变形抗力进行研究.分析了变形温度、变形速率、变形程度对变形抗力的影响,建立一种适合X70、X80高钢级管线钢的变形抗力模型.通过多元非线性进行回归分析,证明模型具有良好的曲线拟合特性.模型成功的应用于轧制生产的现场,计算出的轧制力值误差控制在11%以内.

  3. The Potential Link Between High Angle Grain Boundary Morphology and Grain Boundary Deformation in a Nickel-Based Superalloy (Postprint)

    Science.gov (United States)

    2015-06-01

    B.V. All rights reserved.1. Introduction The creep deformation in polycrystalline nickel based super alloys is a heterogeneous process, the primary...annealing twins in G1 and G2 (TG1 and TG2 respectively). The d via the offset in hafnium oxide grid lines (white) deposited prior to deformation...titanium alloy , Acta Mater. 58 (16) (2010) 5511–5519 , URL 〈http://journals.ohiolink.edu/ejc/article.cgi? issn 13596454&issue v58i0016&article

  4. Dislocations and deformation microstructure in a B2-ordered Al28Co20Cr11Fe15Ni26 high-entropy alloy.

    Science.gov (United States)

    Feuerbacher, Michael

    2016-07-19

    High-entropy alloys are multicomponent metallic materials currently attracting high research interest. They display a unique combination of chemical disorder and crystalline long-range order, and due to their attractive properties are promising candidates for technological application. Many high-entropy alloys possess surprisingly high strength, occasionally in combination with high ductility and low density. The mechanisms effecting these attractive mechanical properties are not understood. This study addresses the deformation mechanism of a Al28Co20Cr11Fe15Ni26 high-entropy alloy, which is a two-phase material, consisting of a B2-ordered matrix and disordered body-centred inclusions. We quantitatively analyse the microstructure and dislocations in deformed samples by transmission-electron-microscopic methods including weak-beam imaging and convergent-beam electron diffraction. We find that the deformation process in the B2 phase is dominated by heterogeneous slip of screw dislocations gliding on planes. The dislocations are perfect superdislocations of the B2 lattice and show no dissociation. This indicates that the antiphase-boundary energy in the structure is very high, inhibiting spread of the dislocation core. Along with the observation of a widely extending strain field associated to the dislocations, our results provide a possible explanation for the high strength of this high-entropy alloy as a direct consequence of its dislocation structure.

  5. Dislocations and deformation microstructure in a B2-ordered Al28Co20Cr11Fe15Ni26 high-entropy alloy

    Science.gov (United States)

    Feuerbacher, Michael

    2016-07-01

    High-entropy alloys are multicomponent metallic materials currently attracting high research interest. They display a unique combination of chemical disorder and crystalline long-range order, and due to their attractive properties are promising candidates for technological application. Many high-entropy alloys possess surprisingly high strength, occasionally in combination with high ductility and low density. The mechanisms effecting these attractive mechanical properties are not understood. This study addresses the deformation mechanism of a Al28Co20Cr11Fe15Ni26 high-entropy alloy, which is a two-phase material, consisting of a B2-ordered matrix and disordered body-centred inclusions. We quantitatively analyse the microstructure and dislocations in deformed samples by transmission-electron-microscopic methods including weak-beam imaging and convergent-beam electron diffraction. We find that the deformation process in the B2 phase is dominated by heterogeneous slip of screw dislocations gliding on planes. The dislocations are perfect superdislocations of the B2 lattice and show no dissociation. This indicates that the antiphase-boundary energy in the structure is very high, inhibiting spread of the dislocation core. Along with the observation of a widely extending strain field associated to the dislocations, our results provide a possible explanation for the high strength of this high-entropy alloy as a direct consequence of its dislocation structure.

  6. A Creep Damage Model for High-Temperature Deformation and Failure of 9Cr-1Mo Steel Weldments

    Directory of Open Access Journals (Sweden)

    Mehdi Basirat

    2015-08-01

    Full Text Available A dislocation-based creep model combined with a continuum damage formulation was developed and implemented in the finite element method to simulate high temperature deformation behavior in modified 9Cr-1Mo steel welds. The evolution of dislocation structures was considered as the main driving mechanism for creep. The effect of void growth, precipitate coarsening, and solid solution depletion were considered to be the operating damage processes. A semi-implicit numerical integration scheme was developed and implemented in the commercial finite element code ABAQUS-Standard as a user material subroutine. Furthermore, several creep tests of modified 9Cr-1Mo steel welded specimens were conducted at temperatures between 550–700 °C and stresses between 80–200 MPa. The accuracy of the model was verified by comparing the finite element results with experiments. The comparison between the experimental and computational results showed excellent agreement. The model can be used to simulate and predict the creep-damage behavior of Cr-Mo steel components used as structural applications in power plants.

  7. A numerical and experimental study of temperature effects on deformation behavior of carbon steels at high strain rates

    Science.gov (United States)

    Pouya, M.; Winter, S.; Fritsch, S.; F-X Wagner, M.

    2017-03-01

    Both in research and in the light of industrial applications, there is a growing interest in methods to characterize the mechanical behavior of materials at high strain rates. This is particularly true for steels (the most important structural materials), where often the strain rate-dependent material behavior also needs to be characterized in a wide temperature range. In this study, we use the Finite Element Method (FEM), first, to model the compressive deformation behavior of carbon steels under quasi-static loading conditions. The results are then compared to experimental data (for a simple C75 steel) at room temperature, and up to testing temperatures of 1000 °C. Second, an explicit FEM model that captures wave propagation phenomena during dynamic loading is developed to closely reflect the complex loading conditions in a Split-Hopkinson Pressure Bar (SHPB) – an experimental setup that allows loading of compression samples with strain rates up to 104 s-1 The dynamic simulations provide a useful basis for an accurate analysis of dynamically measured experimental data, which considers reflected elastic waves. By combining numerical and experimental investigations, we derive material parameters that capture the strain rate- and temperature-dependent behavior of the C75 steel from room temperature to 1000 °C, and from quasi-static to dynamic loading.

  8. Microstructural characteristics of adiabatic shear localization in a metastable beta titanium alloy deformed at high strain rate and elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Zhan, Hongyi, E-mail: h.zhan@uq.edu.au [Centre for Advanced Materials Processing and Manufacture, School of Mechanical and Mining Engineering, The University of Queensland, St Lucia, Queensland 4072 (Australia); Zeng, Weidong [State Key Laboratory of Solidification Processing, School of Materials, Northwestern Polytechnical University, Xi' an 710072 (China); Wang, Gui [Centre for Advanced Materials Processing and Manufacture, School of Mechanical and Mining Engineering, The University of Queensland, St Lucia, Queensland 4072 (Australia); Defence Material Technology Centre, Level 2, 24 Wakefield St, Hawthorn, VIC 3122 (Australia); Kent, Damon [School of Science and Engineering, University of the Sunshine Coast, Sippy Downs, Queensland 4575 (Australia); Dargusch, Matthew [Centre for Advanced Materials Processing and Manufacture, School of Mechanical and Mining Engineering, The University of Queensland, St Lucia, Queensland 4072 (Australia); Defence Material Technology Centre, Level 2, 24 Wakefield St, Hawthorn, VIC 3122 (Australia)

    2015-04-15

    The microstructural evolution and grain refinement within adiabatic shear bands in the Ti6554 alloy deformed at high strain rates and elevated temperatures have been characterized using transmission electron microscopy. No stress drops were observed in the corresponding stress–strain curve, indicating that the initiation of adiabatic shear bands does not lead to the loss of load capacity for the Ti6554 alloy. The outer region of the shear bands mainly consists of cell structures bounded by dislocation clusters. Equiaxed subgrains in the core area of the shear band can be evolved from the subdivision of cell structures or reconstruction and transverse segmentation of dislocation clusters. It is proposed that dislocation activity dominates the grain refinement process. The rotational recrystallization mechanism may operate as the kinetic requirements for it are fulfilled. The coexistence of different substructures across the shear bands implies that the microstructural evolution inside the shear bands is not homogeneous and different grain refinement mechanisms may operate simultaneously to refine the structure. - Graphical abstract: Display Omitted - Highlights: • The microstructure within the adiabatic shear band was characterized by TEM. • No stress drops were observed in the corresponding stress–strain curve. • Dislocation activity dominated the grain refinement process. • The kinetic requirements for rotational recrystallization mechanism were fulfilled. • Different grain refinement mechanisms operated simultaneously to refine the structure.

  9. Deformation and Recrystallization Behavior of the Cast Structure in Large Size, High Strength Steel Ingots: Experimentation and Modeling

    Science.gov (United States)

    Chadha, K.; Shahriari, D.; Tremblay, R.; Bhattacharjee, P. P.; Jahazi, M.

    2017-07-01

    Constitutive modeling of the ingot breakdown process of large size ingots of high strength steel was carried out through comprehensive thermomechanical processing using Gleeble 3800® thermomechanical simulator, finite element modeling (FEM), optical and electron back scatter diffraction (EBSD). For this purpose, hot compression tests in the range of 1473 K to 1323 K (1200 °C to 1050 °C) and strain rates of 0.25 to 2 s-1 were carried out. The stress-strain curves describing the deformation behavior of the dendritic microstructure of the cast ingot were analyzed in terms of the Arrhenius and Hansel-Spittel models which were implemented in Forge NxT 1.0® FEM software. The results indicated that the Arrhenius model was more reliable in predicting microstructure evolution of the as-cast structure during ingot breakdown, particularly the occurrence of dynamic recrystallization (DRX) process which was a vital parameter in estimating the optimum loads for forming of large size components. The accuracy and reliability of both models were compared in terms of correlation coefficient (R) and the average absolute relative error (ARRE).

  10. The potential link between high angle grain boundary morphology and grain boundary deformation in a nickel-based superalloy

    Energy Technology Data Exchange (ETDEWEB)

    Carter, Jennifer L.W., E-mail: jennifer.w.carter@case.edu [Department of Materials Science and Engineering, The Ohio State University, Columbus, OH 44321 (United States); Sosa, John M. [Center for Accelerated Maturation of Materials, The Ohio State University, Columbus, OH 44321 (United States); Shade, Paul A. [Air Force Research Laboratory, Materials & Manufacturing Directorate, AFRL/RXCM, Wright-Patterson AFB, Dayton, OH 45433 (United States); Fraser, Hamish L. [Center for Accelerated Maturation of Materials, The Ohio State University, Columbus, OH 44321 (United States); Uchic, Michael D. [Air Force Research Laboratory, Materials & Manufacturing Directorate, AFRL/RXCM, Wright-Patterson AFB, Dayton, OH 45433 (United States); Mills, Michael J. [Department of Materials Science and Engineering, The Ohio State University, Columbus, OH 44321 (United States)

    2015-07-29

    Focused ion beam (FIB) based serial sectioning was utilized to characterize the morphology of two high angle grain boundaries (HAGB) in a nickel based superalloy, one that experienced grain boundary sliding (GBS) and the other experienced strain accumulation, during elevated temperature constant stress loading conditions. A custom script was utilized to serial section and collect ion-induced secondary electron images from the FIB-SEM system. The MATLAB based MIPAR{sup TM} software was utilized to align, segment and reconstruct 3D volumes from the sectioned images. Analysis of the 3D data indicates that the HAGB that exhibited GBS had microscale curvature that was planar in nature, and local serrations on the order of ±150 nm. In contrast, the HAGB that exhibited strain accumulation was not planar and had local serrations an order of magnitude greater than the other grain boundary. It is hypothesized that the serrations and the local grain boundary network are key factors in determining which grain boundaries experience GBS during creep deformation.

  11. Deformation and Recrystallization Behavior of the Cast Structure in Large Size, High Strength Steel Ingots: Experimentation and Modeling

    Science.gov (United States)

    Chadha, K.; Shahriari, D.; Tremblay, R.; Bhattacharjee, P. P.; Jahazi, M.

    2017-09-01

    Constitutive modeling of the ingot breakdown process of large size ingots of high strength steel was carried out through comprehensive thermomechanical processing using Gleeble 3800® thermomechanical simulator, finite element modeling (FEM), optical and electron back scatter diffraction (EBSD). For this purpose, hot compression tests in the range of 1473 K to 1323 K (1200 °C to 1050 °C) and strain rates of 0.25 to 2 s-1 were carried out. The stress-strain curves describing the deformation behavior of the dendritic microstructure of the cast ingot were analyzed in terms of the Arrhenius and Hansel-Spittel models which were implemented in Forge NxT 1.0® FEM software. The results indicated that the Arrhenius model was more reliable in predicting microstructure evolution of the as-cast structure during ingot breakdown, particularly the occurrence of dynamic recrystallization (DRX) process which was a vital parameter in estimating the optimum loads for forming of large size components. The accuracy and reliability of both models were compared in terms of correlation coefficient (R) and the average absolute relative error (ARRE).

  12. Particle fracture and plastic deformation in vanadium pentoxide powders induced by high energy vibrational ball-mill

    Indian Academy of Sciences (India)

    Partha Chatterjee; S P Sen Gupta; Suchitra Sen

    2001-04-01

    An X-ray powder profile analysis in vanadium pentoxide powder milled in a high energy vibrational ball-mill for different lengths of time (0–250 h), is presented. The strain and size induced broadening of the Bragg reflection for two different crystallographic directions ([001] and [100]) was determined by Warren–Averbach analysis using a pattern-decomposition method assuming a Pseudo–Voigt function. The deformation process caused a decrease in the crystallite size and a saturation of crystallite size of ∼ 10 nm was reached after severe milling. The initial stages of milling indicated a propensity of size-broadening due to fracture of the powder particles caused by repeated ball-to-powder impact whereas with increasing milling time microstrain broadening was predominant. WA analysis indicated significant plastic strain along with spatial confinement of the internal strain fields in the crystallite interfaces. Significant strain anisotropy was noticed in the different crystallographic directions. A near-isotropy in the crystallite size value was noticed for materials milled for 200 h and beyond. The column-length distribution function obtained from the size Fourier coefficients progressively narrowed down with the milling time.

  13. Numerical Simulation of Heat Transfer and Deformation of Initial Shell in Soft Contact Continuous Casting Mold Under High Frequency Electromagnetic Field

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Heat transfer and deformation of initial solidification shell in soft contact continuous casting moldunder high frequency electromagnetic field were analyzed using numerical simulation method; the relative electromagnetic parameters were obtained from the previous studies. Owing to the induction heating of a high frequency electromagnetic field (20 kHz), the thickness of initial solidification shell decreases, and the temperature of strand surface and slit copper mold increases when compared with the case without the electromagnetic filed. The viscosity of flux decreases because of the induction heating of the high frequency electromagnetic field, and the dimension of the flux channel increases with electromagnetic pressure; thus, the deformation behavior of initial solidification shell was different before and after the action of high frequency electromagnetic field. Furthermore, the abatement mechanism of oscillation marks under high frequency electromagnetic field was explained.

  14. Chondrocyte Deformations as a Function of Tibiofemoral Joint Loading Predicted by a Generalized High-Throughput Pipeline of Multi-Scale Simulations

    Science.gov (United States)

    Sibole, Scott C.; Erdemir, Ahmet

    2012-01-01

    Cells of the musculoskeletal system are known to respond to mechanical loading and chondrocytes within the cartilage are not an exception. However, understanding how joint level loads relate to cell level deformations, e.g. in the cartilage, is not a straightforward task. In this study, a multi-scale analysis pipeline was implemented to post-process the results of a macro-scale finite element (FE) tibiofemoral joint model to provide joint mechanics based displacement boundary conditions to micro-scale cellular FE models of the cartilage, for the purpose of characterizing chondrocyte deformations in relation to tibiofemoral joint loading. It was possible to identify the load distribution within the knee among its tissue structures and ultimately within the cartilage among its extracellular matrix, pericellular environment and resident chondrocytes. Various cellular deformation metrics (aspect ratio change, volumetric strain, cellular effective strain and maximum shear strain) were calculated. To illustrate further utility of this multi-scale modeling pipeline, two micro-scale cartilage constructs were considered: an idealized single cell at the centroid of a 100×100×100 μm block commonly used in past research studies, and an anatomically based (11 cell model of the same volume) representation of the middle zone of tibiofemoral cartilage. In both cases, chondrocytes experienced amplified deformations compared to those at the macro-scale, predicted by simulating one body weight compressive loading on the tibiofemoral joint. In the 11 cell case, all cells experienced less deformation than the single cell case, and also exhibited a larger variance in deformation compared to other cells residing in the same block. The coupling method proved to be highly scalable due to micro-scale model independence that allowed for exploitation of distributed memory computing architecture. The method’s generalized nature also allows for substitution of any macro-scale and/or micro

  15. Chondrocyte deformations as a function of tibiofemoral joint loading predicted by a generalized high-throughput pipeline of multi-scale simulations.

    Directory of Open Access Journals (Sweden)

    Scott C Sibole

    Full Text Available Cells of the musculoskeletal system are known to respond to mechanical loading and chondrocytes within the cartilage are not an exception. However, understanding how joint level loads relate to cell level deformations, e.g. in the cartilage, is not a straightforward task. In this study, a multi-scale analysis pipeline was implemented to post-process the results of a macro-scale finite element (FE tibiofemoral joint model to provide joint mechanics based displacement boundary conditions to micro-scale cellular FE models of the cartilage, for the purpose of characterizing chondrocyte deformations in relation to tibiofemoral joint loading. It was possible to identify the load distribution within the knee among its tissue structures and ultimately within the cartilage among its extracellular matrix, pericellular environment and resident chondrocytes. Various cellular deformation metrics (aspect ratio change, volumetric strain, cellular effective strain and maximum shear strain were calculated. To illustrate further utility of this multi-scale modeling pipeline, two micro-scale cartilage constructs were considered: an idealized single cell at the centroid of a 100×100×100 μm block commonly used in past research studies, and an anatomically based (11 cell model of the same volume representation of the middle zone of tibiofemoral cartilage. In both cases, chondrocytes experienced amplified deformations compared to those at the macro-scale, predicted by simulating one body weight compressive loading on the tibiofemoral joint. In the 11 cell case, all cells experienced less deformation than the single cell case, and also exhibited a larger variance in deformation compared to other cells residing in the same block. The coupling method proved to be highly scalable due to micro-scale model independence that allowed for exploitation of distributed memory computing architecture. The method's generalized nature also allows for substitution of any macro

  16. Ultrasoft, highly deformable microgels.

    Science.gov (United States)

    Bachman, Haylee; Brown, Ashley C; Clarke, Kimberly C; Dhada, Kabir S; Douglas, Alison; Hansen, Caroline E; Herman, Emily; Hyatt, John S; Kodlekere, Purva; Meng, Zhiyong; Saxena, Shalini; Spears, Mark W; Welsch, Nicole; Lyon, L Andrew

    2015-03-14

    Microgels are colloidally stable, hydrogel microparticles that have previously been used in a range of (soft) material applications due to their tunable mechanical and chemical properties. Most commonly, thermo and pH-responsive poly(N-isopropylacrylamide) (pNIPAm) microgels can be fabricated by precipitation polymerization in the presence of the co-monomer acrylic acid (AAc). Traditionally pNIPAm microgels are synthesized in the presence of a crosslinking agent, such as N,N'-methylenebisacrylamide (BIS), however, microgels can also be synthesized under 'crosslinker free' conditions. The resulting particles have extremely low (biomedical applications including biomaterials for drug delivery and regenerative medicine.

  17. INVESTIGATION BY NUMERICAL MODELING OF INFLUENCE OF THE SHAPE OF DEFORMING ZONE OF DIE AT WIRE DRAWING OF STEEL HIGH-CARBON WIRE ON TEMPERATURE AND MODE OF DEFORMATION IN WIRE AND DIE

    Directory of Open Access Journals (Sweden)

    Ju. L. Bobarikin

    2010-01-01

    Full Text Available Investigation by numerical modeling of influence of the form of deforming zone of die at drawing of steel highcarbon wire on temperature and strained-deformed state in wire and die is carried out.

  18. Haglund's Deformity

    Science.gov (United States)

    ... to follow the surgeon’s instructions for postsurgical care. Prevention To help prevent a recurrence of Haglund’s deformity: wear appropriate shoes; avoid shoes with a rigid heel back use arch supports or orthotic devices perform stretching exercises to prevent the Achilles tendon from tightening ...

  19. Microstructure and High Temperature Plastic Deformation Behavior of Al-12Si Based Alloy Fabricated by an Electromagnetic Casting and Stirring Process

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Kyung-Soo; Roh, Heung-Ryeol; Kim, Mok-Soon [Inha University, Incheon (Korea, Republic of); Kim, Jong-Ho; Park, Joon-Pyo [Research Institute of Industrial Science and Technology, Pohang (Korea, Republic of)

    2017-06-15

    An as-received EMC/S (electromagnetic casting and stirring)-processed Al-12Si based alloy billet was homogenized to examine its microstructure and high temperature plastic deformation behavior, using compressive tests over the temperature range from 623 to 743 K and a strain rate range from 1.0×10{sup -3} to 1.0×10{sup 0}s{sup -1}. The results were compared with samples processed by the direct chill casting (DC) method. The fraction of equiaxed structure for the as-received EMC/S billet(41%) was much higher than that of the as-received DC billet(6 %). All true stress – true strain curves acquired from the compressive tests exhibited a peak stress at the initial stage of plastic deformation. Flow stress showed a steady state region after the appearance of peak stress with increasing strain. The peak stress decreased with increasing temperature at a given strain rate and a decreasing strain rate at a given temperature. A constitutive equation was made for each alloy, which could be used to predict the peak stress. A recrystallized grain structure was observed in all the deformed specimens, indicating that dynamic recrystallization is the predominant mechanism during high temperature plastic deformation of both the homogenized EMC/S and DC-processed Al-12Si based alloys.

  20. Cyclic Deformation Behavior of Fe-18Cr-18Mn-0.63N Nickel-Free High-Nitrogen Austenitic Stainless Steel

    Science.gov (United States)

    Shao, C. W.; Shi, F.; Li, X. W.

    2015-04-01

    Cyclic deformation and damage behavior of a Ni-free high-nitrogen austenitic stainless steel with a composition of Fe-18Cr-18Mn-0.63N (weight pct) were studied, and the internal stress and effective stress were estimated by partitioning the hysteresis loop during cyclic straining at total strain amplitudes ranging from 3.0 × 10-3 to 1.0 × 10-2. It is found that immediate cyclic softening takes place at all strain amplitudes and subsequently a saturation or quasi-saturation state develops and occupies the main part of the whole fatigue life. The internal stress increases with increasing strain amplitude, while the variation of effective stress with strain amplitude is somewhat complicated. Such a phenomenon is discussed in terms of dislocation structures and the short-range ordering caused by the interaction between nitrogen atoms and substitutional atoms. The relationship of fatigue life vs plastic strain amplitude ( N f-Δ ɛ pl/2) follows a bilinear Coffin-Manson rule, resulting from the variation in slip deformation mode with the applied strain amplitude. At the low strain amplitude, cracks initiate along slip bands, and planar slip dislocation configurations dominate the major characteristic of internal microstructures. At high strain amplitudes, intergranular (mostly along grain boundaries and few along twin boundaries) cracks are generally found, and the deformation microstructures are mainly composed of dislocation cells, stacking faults and a small amount of deformation twins, in addition to planar slip dislocation structures.

  1. Microscopic Deformation of Tungsten Surfaces by High Energy and High Flux Helium/Hydrogen Particle Bombardment with Short Pulses

    Science.gov (United States)

    Tokitani, Masayuki; Yoshida, Naoaki; Tokunaga, Kazutoshi; Sakakita, Hajime; Kiyama, Satoru; Koguchi, Haruhisa; Hirano, Yoichi; Masuzaki, Suguru

    The neutral beam injection facility in the National Institute of Advanced Industrial Science and Technology was used to irradiate a polycrystalline tungsten specimen with high energy and high flux helium and hydrogen particles. The incidence energy and flux of the beam shot were 25 keV and 8.8 × 1022 particles/m2 s, respectively. The duration of each shot was approximately 30 ms, with 6 min intervals between each shot. Surface temperatures over 1800 K were attained. In the two cases of helium irradiation, total fluence of either 1.5 × 1022 He/m2 or 4.0 × 1022 He/m2 was selected. In the former case, large sized blisters with diameter of 500 nm were densely observed. While, the latter case, the blisters were disappeared and fine nanobranch structures appeared instead. Cross-sectional observations using a transmission electron microscope (TEM) with the focused ion beam (FIB) technique were performed. According to the TEM image, after irradiation with a beam shot of total fluence 4.0 × 1022 He/m2 , there were very dense fine helium bubbles in the tungsten of sizes 1-50 nm. As the helium bubbles grew the density of the tungsten matrix drastically decreased as a result of void swelling. These effects were not seen in hydrogen irradiation case.

  2. Slope deformations in high-mountain regions as observed by InSAR: Examples from the Cordillera Blanca, Peru

    Science.gov (United States)

    Frey, Holger; Strozzi, Tazio; Caduff, Rafael; Huggel, Christian; Klimeš, Jan; Vilímek, Vít; Wiesmann, Andreas; Kääb, Andreas; Cochachin, Alejo; Plummer, Stephen

    2016-04-01

    the dry period. Data archives of spaceborne SAR sensors such as ERS-1/2, ENVISAT, ALOS PALSAR-1/2, TerraSAR-X, Radarsat-2 and Sentinel-1 provide information reaching back to the 1990ies, allowing for detection and analysis of both current and past processes. Environmental conditions in the Peruvian Andes are particularly favourable for InSAR analyses, with an extended period of mostly cloud-free conditions during austral winter (dry season), sparse vegetation cover and only very limited snow coverage, factors that in other regions often limit the potential of this technology. This contribution shows the potential of InSAR products, providing unique information on slope deformations and surface displacements as identified as an important information source for integrative hazard assessments and glaciological investigations in high-mountain regions. In particular in combination with field investigations this technology is very powerful, not only for hazard research, but for other types of applications related to surface displacements and terrain deformations. In regions like the Cordillera Blanca, where a variety of potentially hazardous and interacting processes are present, often under conditions beyond historical evidences, such data products provide invaluable information for hazard assessments, early detection of hazard potentials, and a basis for prioritization and decision-making by the authorities.

  3. 4D very high-resolution topography monitoring of surface deformation using UAV-SfM framework.

    Science.gov (United States)

    Clapuyt, François; Vanacker, Veerle; Schlunegger, Fritz; Van Oost, Kristof

    2016-04-01

    During the last years, exploratory research has shown that UAV-based image acquisition is suitable for environmental remote sensing and monitoring. Image acquisition with cameras mounted on an UAV can be performed at very-high spatial resolution and high temporal frequency in the most dynamic environments. Combined with Structure-from-Motion algorithm, the UAV-SfM framework is capable of providing digital surface models (DSM) which are highly accurate when compared to other very-high resolution topographic datasets and highly reproducible for repeated measurements over the same study area. In this study, we aim at assessing (1) differential movement of the Earth's surface and (2) the sediment budget of a complex earthflow located in the Central Swiss Alps based on three topographic datasets acquired over a period of 2 years. For three time steps, we acquired aerial photographs with a standard reflex camera mounted on a low-cost and lightweight UAV. Image datasets were then processed with the Structure-from-Motion algorithm in order to reconstruct a 3D dense point cloud representing the topography. Georeferencing of outputs has been achieved based on the ground control point (GCP) extraction method, previously surveyed on the field with a RTK GPS. Finally, digital elevation model of differences (DOD) has been computed to assess the topographic changes between the three acquisition dates while surface displacements have been quantified by using image correlation techniques. Our results show that the digital elevation model of topographic differences is able to capture surface deformation at cm-scale resolution. The mean annual displacement of the earthflow is about 3.6 m while the forefront of the landslide has advanced by ca. 30 meters over a period of 18 months. The 4D analysis permits to identify the direction and velocity of Earth movement. Stable topographic ridges condition the direction of the flow with highest downslope movement on steep slopes, and diffuse

  4. Deformation mechanisms in experimentally deformed Boom Clay

    Science.gov (United States)

    Desbois, Guillaume; Schuck, Bernhard; Urai, Janos

    2016-04-01

    Bulk mechanical and transport properties of reference claystones for deep disposal of radioactive waste have been investigated since many years but little is known about microscale deformation mechanisms because accessing the relevant microstructure in these soft, very fine-grained, low permeable and low porous materials remains difficult. Recent development of ion beam polishing methods to prepare high quality damage free surfaces for scanning electron microscope (SEM) is opening new fields of microstructural investigation in claystones towards a better understanding of the deformation behavior transitional between rocks and soils. We present results of Boom Clay deformed in a triaxial cell in a consolidated - undrained test at a confining pressure of 0.375 MPa (i.e. close to natural value), with σ1 perpendicular to the bedding. Experiments stopped at 20 % strain. As a first approximation, the plasticity of the sample can be described by a Mohr-Coulomb type failure envelope with a coefficient of cohesion C = 0.117 MPa and an internal friction angle ϕ = 18.7°. After deformation test, the bulk sample shows a shear zone at an angle of about 35° from the vertical with an offset of about 5 mm. We used the "Lamipeel" method that allows producing a permanent absolutely plane and large size etched micro relief-replica in order to localize and to document the shear zone at the scale of the deformed core. High-resolution imaging of microstructures was mostly done by using the BIB-SEM method on key-regions identified after the "Lamipeel" method. Detailed BIB-SEM investigations of shear zones show the following: the boundaries between the shear zone and the host rock are sharp, clay aggregates and clastic grains are strongly reoriented parallel to the shear direction, and the porosity is significantly reduced in the shear zone and the grain size is smaller in the shear zone than in the host rock but there is no evidence for broken grains. Comparison of microstructures

  5. Dynamic behavior and microstructural evolution during moderate to high strain rate hot deformation of a Fe-Ni-Cr alloy (alloy 800H)

    Science.gov (United States)

    Cao, Yu; Di, Hongshuang; Zhang, Jiecen; Yang, Yaohua

    2015-01-01

    The objective of the study is to fundamentally understand the dynamic behavior of alloy 800H at moderate to high strain rate using hot compression tests and propose nucleation mechanism associated with dynamic crystallization (DRX). We firstly investigated the dynamic behavior of alloy 800H with industrial scale strain rates using hot compression tests and adiabatic correction was performed to correct as-measured flow curves. Secondly, a Johnson-Cook model was established by using the corrected data and could give a precise prediction of elevated temperature flow stress for the studied alloy. Finally, the nucleation mechanism of DRX grains at high strain rates was studied. The results showed that the predominant nucleation mechanism for DRX is the formation of "bulge" at parent grain boundary. Additionally, the fragmentation of original grain at low deformation temperatures and the twinning near the bulged regions at high deformation temperatures also accelerate the DRX process.

  6. Investigation of medium to high strain deformation microstructures using an automated electron back scatter pattern (EBSP) system

    Energy Technology Data Exchange (ETDEWEB)

    Godfrey, A.; Hughes, D.A. [Sandia National Labs., Livermore, CA (United States). Center for Materials and Applied Mechanics; Krieger Lassen, N.C.; Jensen, D.J. [Riso National Lab., Roskilde (Denmark). Materials Dept.

    1998-03-01

    The speed of automated EBSP orientation gathering has now increased to a point where it is possible to examine large areas of deformed material at a resolution close to the length scale of the dislocation substructures involved (typically < 1 {micro}m for strains of greater than {epsilon} = 1). Investigation of such deformed samples invariably gives rise to diffraction images of low quality and to many double patterns. To assist in a critical selection of the data, it is usual to store a measure of the indexing confidence for each point. Here the authors describe how deformed samples, which provide the appropriate range of pattern qualities, can be used to calibrate acceptance criteria for unsupervised EBSP measurements on deformation microstructures. An application in the use of such criteria is also described. Two crystals chosen with orientations that are known to develop a well defined texture spread during deformation were channel die deformed to a strain of {epsilon} = 1.5 (78% reduction). The texture spread was determined for each sample from a large number of transmission electron microscope (TEM) orientation measurements taken using a fast semi-automatic technique. EBSP scans were then made on the samples. Orientations failing within the expected (TEM determined) texture spread are assumed to be correct. While those falling outside the expected spread are assumed to be incorrect. Unsupervised acceptance criteria based on an indexing confidence parameter (in their case the fraction of located Kikuchi bands matching the indexing solution) were then tested by comparing the set of orientations selected using a given approval criterion with the set of the orientations falling within the expected spread. Criteria were appraised by determining both the fraction of all orientations that were misclassified (incorrect orientations selected plus correct orientations not selected) or by the fraction of incorrect orientations in the selected data set.

  7. High-Temperature Deformation Processing Map Approach for Obtaining the Desired Microstructure in a Multi-component (Ni-Ti-Cu-Fe) Alloy

    Science.gov (United States)

    Nayan, Niraj; Singh, Gaurav; Narayana Murty, S. V. S.; Jha, Abhay K.; Pant, Bhanu; George, Koshy M.

    2015-05-01

    An equiatomic NiTiCuFe multi-component alloy with simple body-centered cubic (bcc) and face-centered cubic solid-solution phases in the microstructure was processed by vacuum induction melting furnace under dynamic Ar atmosphere. High-temperature uniaxial compression experiments were conducted on it in the temperature range of 1073 K to 1303 K (800 °C to 1030 °C) and strain rate range of 10-3 to 10-1 s-1. The data generated were analyzed with the aid of the dynamic materials model through which power dissipation efficiency and instability maps were generated so as to identify the governing deformation mechanisms that are operative in different temperature-strain rate regimes with the aid of complementary microstructural analysis of the deformed specimens. Results indicate that the stable domain for the high temperature deformation of the multi-component alloy occurs in the temperature range of 1173 K to 1303 K (900 °C to 1030 °C) and range of 10-3 to 10-1.2 s-1, and the deformation is unstable at T = 1073 K to 1153 K (800 °C to 880 °C) and = 10-3 to 10-1.4 s-1 as well as T = 1223 K to 1293 K (950 °C to 1020 °C) and = 10-1.4 to 10-1 s-1, with adiabatic shear banding, localized plastic flow, or cracking being the unstable mechanisms. A constitutive equation that describes the flow stress of NiTiCuFe multi-component alloy as a function of strain rate and deformation temperature was also determined.

  8. Genu Recurvatum Deformity in a Child due to Salter Harris Type V Fracture of the Proximal Tibial Physis Treated with High Tibial Dome Osteotomy

    Directory of Open Access Journals (Sweden)

    Theodoros Beslikas

    2012-01-01

    Full Text Available Salter-Harris type V fracture is a very rare injury in the immature skeleton. In most cases, it remains undiagnosed and untreated. We report a case of genu recurvatum deformity in a 15-year-old boy caused by a Salter-Harris type V fracture of the proximal tibial physis. The initial X-ray did not reveal fracture. One year after injury, genu recurvatum deformity was detected associated with significant restriction of knee flexion and limp length discrepancy (2 cm as well as medial and posterior instability of the joint. Further imaging studies revealed anterior bone bridge of the proximal tibial physis. The deformity was treated with a high tibial dome osteotomy combined with a tibial tubercle osteotomy stabilized with malleolar screws and a cast. Two years after surgery, the patient gained functional knee mobility without clinical instability. Firstly, this case highlights the importance of early identification of this rare lesion (Salter-Harris type V fracture and, secondly, provides an alternative method of treatment for genu recurvatum deformity.

  9. Genu Recurvatum Deformity in a Child due to Salter Harris Type V Fracture of the Proximal Tibial Physis Treated with High Tibial Dome Osteotomy.

    Science.gov (United States)

    Beslikas, Theodoros; Christodoulou, Andreas; Chytas, Anastasios; Gigis, Ioannis; Christoforidis, John

    2012-01-01

    Salter-Harris type V fracture is a very rare injury in the immature skeleton. In most cases, it remains undiagnosed and untreated. We report a case of genu recurvatum deformity in a 15-year-old boy caused by a Salter-Harris type V fracture of the proximal tibial physis. The initial X-ray did not reveal fracture. One year after injury, genu recurvatum deformity was detected associated with significant restriction of knee flexion and limp length discrepancy (2 cm) as well as medial and posterior instability of the joint. Further imaging studies revealed anterior bone bridge of the proximal tibial physis. The deformity was treated with a high tibial dome osteotomy combined with a tibial tubercle osteotomy stabilized with malleolar screws and a cast. Two years after surgery, the patient gained functional knee mobility without clinical instability. Firstly, this case highlights the importance of early identification of this rare lesion (Salter-Harris type V fracture) and, secondly, provides an alternative method of treatment for genu recurvatum deformity.

  10. Modeling the Effects of Cu Content and Deformation Variables on the High-Temperature Flow Behavior of Dilute Al-Fe-Si Alloys Using an Artificial Neural Network.

    Science.gov (United States)

    Shakiba, Mohammad; Parson, Nick; Chen, X-Grant

    2016-06-30

    The hot deformation behavior of Al-0.12Fe-0.1Si alloys with varied amounts of Cu (0.002-0.31 wt %) was investigated by uniaxial compression tests conducted at different temperatures (400 °C-550 °C) and strain rates (0.01-10 s(-1)). The results demonstrated that flow stress decreased with increasing deformation temperature and decreasing strain rate, while flow stress increased with increasing Cu content for all deformation conditions studied due to the solute drag effect. Based on the experimental data, an artificial neural network (ANN) model was developed to study the relationship between chemical composition, deformation variables and high-temperature flow behavior. A three-layer feed-forward back-propagation artificial neural network with 20 neurons in a hidden layer was established in this study. The input parameters were Cu content, temperature, strain rate and strain, while the flow stress was the output. The performance of the proposed model was evaluated using the K-fold cross-validation method. The results showed excellent generalization capability of the developed model. Sensitivity analysis indicated that the strain rate is the most important parameter, while the Cu content exhibited a modest but significant influence on the flow stress.

  11. Modeling the Effects of Cu Content and Deformation Variables on the High-Temperature Flow Behavior of Dilute Al-Fe-Si Alloys Using an Artificial Neural Network

    Directory of Open Access Journals (Sweden)

    Mohammad Shakiba

    2016-06-01

    Full Text Available The hot deformation behavior of Al-0.12Fe-0.1Si alloys with varied amounts of Cu (0.002–0.31 wt % was investigated by uniaxial compression tests conducted at different temperatures (400 °C–550 °C and strain rates (0.01–10 s−1. The results demonstrated that flow stress decreased with increasing deformation temperature and decreasing strain rate, while flow stress increased with increasing Cu content for all deformation conditions studied due to the solute drag effect. Based on the experimental data, an artificial neural network (ANN model was developed to study the relationship between chemical composition, deformation variables and high-temperature flow behavior. A three-layer feed-forward back-propagation artificial neural network with 20 neurons in a hidden layer was established in this study. The input parameters were Cu content, temperature, strain rate and strain, while the flow stress was the output. The performance of the proposed model was evaluated using the K-fold cross-validation method. The results showed excellent generalization capability of the developed model. Sensitivity analysis indicated that the strain rate is the most important parameter, while the Cu content exhibited a modest but significant influence on the flow stress.

  12. Inconel690合金高温高速热变形行为研究%High-Temperature High-Speed Hot Deformation Behavior of Inconel 690 Alloy

    Institute of Scientific and Technical Information of China (English)

    王彬; 程明; 张士宏; 宋鸿武

    2011-01-01

    在Gleeble-3800热模拟试验机上,采用热压缩实验研究了不同变形条件下Inconel 690合金的高温变形行为与组织演变特点.实验中采用的变形温度为1000~1200℃,变形量为70%,变形速率为1.0 ~80.0 s-1.根据实验结果获得了该合金的应力-应变关系,并对峰值应力进行了线性回归,由此得到了该合金的高温材料常数,激活能Q =417.6 kJ.mo1-1,α =0.003196 MPa-1,n=7.51,并最终得到了Incone1690合金的高温变形本构方程.通过金相显微镜研究了合金动态再结晶规律与温度和应变速率的关系,结果表明:变形温度对Inconel 690合金组织的影响很大,随温度的升高,动态再结晶百分数逐渐增加,且伴随着晶粒的长大;而提高应变速率,变形的时间缩短,位错密度迅速增大,动态再结晶的驱动力增加,也可以使再结晶后的晶粒细化;当温度为1150℃左右,应变速率50~80 s-1时,能够得到均匀细晶组织.%The hot deformation characteristics of Inconel 690 alloy were investigated on the Gleeble-3800 thermal mechanical simulator. The testing temperatures were in the range of 1000 ~ 1200 ℃, the deformation degree was 70% , and the strain rates were from 1.0 to 80.0 s-1. The true stress-strain curves were obtained and the material constants, the activation energy Q of 417.6 kJ·mol-1, α of 0.0031% Mpa-1, and re of 7.51, of high-temperature deformation of Inconel 690 alloy were obtained by the linear regression of peak stress. The constitutive equation of inconel 690 alloy was established finally. The relationship between the law of dynamic recrys-tallization and temperature, strain rate was studied by metallurgical microscope. The results showed that the microstructures of inconel 690 alloy were greatly affected by temperature, the percentage of dynamic recrystallization increased with the increasing of temperature, and accompanied by grain growth. The deformation time shortened while the strain rate

  13. Experimental deformation of natural diabase at high-pressure: implications for the rheology of the lower crust

    Science.gov (United States)

    Goergen, E. T.; Hirth, G.

    2009-12-01

    Mechanical and microstructural data are presented from a series of experiments on different bulk compositions of natural diabase. The purpose of these experiments is to investigate the rheological properties of diabase at high pressure, to clarify the effect of fH2O on the strengths of these materials, and to quantify microstructural evolution with increasing strain, all with application to the rheology and evolution of the lower crust. The rheological behavior of the lower crust exerts control on many important large-scale geodynamic processes such as crust-mantle coupling, crustal extension and delamination, and the long-term stability of mountain systems. Although the rheological characteristics of the lower crust can be approximated by a mafic composition (e.g. mafic granulite, gabbro etc.), even slight lateral and vertical crustal heterogeneities with respect to bulk composition, including water content, result in changes in the stable phase assemblage, the modal abundance of constituent phases, and, by extension, the relative strength of a rock volume. For example, the Columbia and Maryland diabases both contain a plagioclase and pyroxene assemblage, however, they differ in the modally dominant phase (plagioclase-Columbia, pyroxene-Maryland) that results if very different relative strengths of these materials (Columbia diabase: relatively weak, Maryland diabase: relatively strong)(Mackwell et al., 1998). Initial experiments have been performed on dry and ‘as is’ samples of Columbia Diabase. Dry samples were processed in a controlled atmosphere furnace using a fO2 near the Fe-FeO buffer at 1050°C for 48 hours. Constant displacement and strain-rate stepping axial compression experiments were carried out in a modified Griggs solid-medium apparatus. Experiments were conducted at a confining pressure of 1 GPa at 900°C using a 10-5/s strain-rate to finite strains ranging from 10 to 40%. Strain-rate stepping experiments were conducted using a 10-5/s strain

  14. The role of subducting bathymetric highs on the oceanic crust to deformation of accretionary wedge and earthquake segmentation in the Java forearc

    Science.gov (United States)

    Singh, S. C.; Mukti, M.; Deighton, I.

    2014-12-01

    Stratigraphic and structural observations of newly acquired seismic reflection data along the offshore south Java reveal the structural style of deformation along the forearc and the role of subducting bathymetric highs to the morphology of the forearc region. The forearc region can be divided in to two major structural units: accretionary wedge and forearc and forearc basin where a backthrust marks the boundary between the accretionary wedge and the forearc basin sediments. The continuous compression in the subduction zone has induced younger landward-vergent folds and thrusts within the seaward margin of the forearc basin sediments, which together with the backthrust is referred as the Offshore South Java Fault Zone (OSJFZ), representing the growth of the accretionary wedge farther landward. Seaward-vergent imbricated thrusts have deformed the sediments in the accretionary wedge younging seaward, and have developed fold-thrust belts in the accretionary wedge toward trench. Together with the backthrusts, these seaward-vergent thrusts characterize the growth of accretionary wedge in South of Java trench. Based on these new results, we suggest that accretionary wedge mechanic is not the first order factor in shaping the morphology of the accretionary wedge complex. Instead the subducting bathymetric highs play the main role in shaping the forearc that are manifested in the uplift of the forearc high and intense deformation along the OSJFZ. These subducting highs also induce compression within the accretionary sediments, evident from landward deflection of the subduction front at the trench and inner part of accretionary wedge in the seaward margin of the forearc basin. Intense deformation is also observed on the seaward portion of the accretionary wedge area where the bathymetric highs subducted. We suggest that these subducted bathymetric features define the segment boundaries for megathrust earthquakes, and hence reducing the maximum size of the earthquakes in the

  15. Nanomechanical Properties and Deformation Behaviors of Multi-Component (AlCrTaTiZrNxSiy High-Entropy Coatings

    Directory of Open Access Journals (Sweden)

    Shao-Yi Lin

    2013-12-01

    Full Text Available In this study multi-component (AlCrTaTiZrNxSiy high-entropy coatings were developed by co-sputtering of AlCrTaTiZr alloy and Si in an Ar/N2 mixed atmosphere with the application of different substrate biases and Si-target powers. Their nanomechanical properties and deformation behaviors were characterized by nanoindentation tests. Because of the effect of high mixing entropies, all the deposited multi-component (AlCrTaTiZrNxSiy high-entropy coatings exhibited a simple face-centered cubic solid-solution structure. With an increased substrate bias and Si-target power, their microstructures changed from large columns with a [111] preferred orientation to a nanocomposite form with ultrafine grains. The hardness, H/E ratio and H3/E2 ratio of (AlCrTaTiZrN1.07Si0.15 coating reached 30.2 GPa, 0.12 and 0.41 GPa, respectively, suggesting markedly suppressed dislocation activities and a very high resistance to wear and plastic deformation, attributable to grain refinements and film densification by the application of substrate bias, a nanocomposite structure by the introduction of silicon nitrides, and a strengthening effect induced by severe lattice distortions. In the deformed regions under indents, stacking faults or partial dislocations were formed, while in the stress-released regions, near-perfect lattices recovered.

  16. THEORETICAL INVESTIGATIONS OF DEFORMATION MODE OF THE INTERMEDIATE HIGH VOLTAGE SUPPORTS UNDER THE ACTION OF LOADS FROM THE BROKEN WIRES

    Directory of Open Access Journals (Sweden)

    Игорь Михайлович Гаранжа

    2016-05-01

    Full Text Available We have completed some theoretical investigations of deformation mode of lattice intermediate supports with suspended insulating garlands with further experimental verification of the results. The necessity of accounting the dynamic component of the emergency load for the design, review and reconstruction of overhead power lines has been substantiated.

  17. Deformable paper origami optoelectronic devices

    KAUST Repository

    He, Jr-Hau

    2017-01-19

    Deformable optoelectronic devices are provided, including photodetectors, photodiodes, and photovoltaic cells. The devices can be made on a variety of paper substrates, and can include a plurality of fold segments in the paper substrate creating a deformable pattern. Thin electrode layers and semiconductor nanowire layers can be attached to the substrate, creating the optoelectronic device. The devices can be highly deformable, e.g. capable of undergoing strains of 500% or more, bending angles of 25° or more, and/or twist angles of 270° or more. Methods of making the deformable optoelectronic devices and methods of using, e.g. as a photodetector, are also provided.

  18. Deformation of a continental margin sequence under a thrust sheet: complex stress history in a high pressure cell revealed by vein systems in the Oman Mountains

    Science.gov (United States)

    Virgo, Simon; Urai, Janos L.; Grobe, Arne

    2016-04-01

    Seven deformation phases can be mapped in mesozoic carbonates of the Jebel Akhdar mountains in North Oman. These include an early horizontal NE-SW directed extension that produced bedding confined vein sets with evidence for anticlockwise rotation of the stress field over time, interpreted to have developed during the thrust sheet emplacement. It is followed by a phase of top-NE bedding parallel shearing which rotates these veins on the North side of the mountains. The next phase is normal to oblique slip faults followed by at least two phases of strike-slip deformation. A "background" ductile deformation (maximum burial temperatures of 250 °C) is shown bu deformed fossils and diagenetic concretions. Each of these phases is consistently documented by a large number of observations of overprinting in nearly continuous outcrops. Each deformation phase produces vein sets that do not only differ in orientation but also in occurrence and appearance. Early vein sets exhibit a high stratigraphic variability, but are laterally very stable. With the onset of faulting, the stratigraphic variability decreases and the lateral variability becomes more significant. Even though the area offers excellent outcrop conditions with nearly 100% exposure, it is virtually impossible to find two outcrops that exhibit the same vein patterns. This has interesting implications for vein system analysis and is due to two reasons: (1) the stratigraphic and lateral variability of occurrence and orientation of each vein set cause different combination of vein sets do develop in different layers (2) Intersecting vein sets can show very different interaction such as crosscutting and reactivation, depending on the mechanical properties of the host rock and the veins.

  19. [Deformations of the vertebral column in the visually impaired schoolchildren presenting with complicated high myopia and the possibilities for its correction].

    Science.gov (United States)

    Egorova, T S; Smirnova, T S; Romashin, O V; Egorova, I V

    2016-01-01

    Complicated high myopia is one of the leading causes responsible for the disablement in the children associated with visual impairment especially when it is combined with other pathological conditions and abnormalities among which are disorders of the musculoskeletal system. In the present study, we for the first time examined visually impaired schoolchildren (n=44) who suffered from high myopia complications making use of the computed optical topographer for the evaluation of the state of their vertebral column. The control group consisted of 60 children attending a secondary school. The study revealed various deformations of the musculoskeletal system including scoliosis, misalignment of the pelvis, kyphosis, hyperlordosis, torsion, platypodia, deformation of the lower extremities and the chest. These deformations were more pronounced in the visually impaired schoolchildren in comparison with the children of the same age comprising the control group (pvertebral column with the use of the apparatus yields an important information for the elaboration and application of a series of measures for the timely provision of medical assistance needed for the comprehensive rehabilitation of the visually impaired schoolchildren presenting with high myopia complications.

  20. Autogenous Deformation of Concrete

    DEFF Research Database (Denmark)

    Autogenous deformation of concrete can be defined as the free deformation of sealed concrete at a constant temperature. A number of observed problems with early age cracking of high-performance concretes can be attributed to this phenomenon. During the last 10 years , this has led to an increased...... focus on autogenous deformation both within concrete practice and concrete research. Since 1996 the interest has been significant enough to hold international, yearly conferences entirely devoted to this subject. The papers in this publication were presented at two consecutive half-day sessions...... at the American Concrete Institute’s Fall Convention in Phoenix, Arizona, October 29, 2002. All papers have been reviewed according to ACI rules. This publication, as well as the sessions, was sponsored by ACI committee 236, Material Science of Concrete. The 12 presentations from 8 different countries indicate...

  1. Autogenous Deformation of Concrete

    DEFF Research Database (Denmark)

    Autogenous deformation of concrete can be defined as the free deformation of sealed concrete at a constant temperature. A number of observed problems with early age cracking of high-performance concretes can be attributed to this phenomenon. During the last 10 years , this has led to an increased...... focus on autogenous deformation both within concrete practice and concrete research. Since 1996 the interest has been significant enough to hold international, yearly conferences entirely devoted to this subject. The papers in this publication were presented at two consecutive half-day sessions...... at the American Concrete Institute’s Fall Convention in Phoenix, Arizona, October 29, 2002. All papers have been reviewed according to ACI rules. This publication, as well as the sessions, was sponsored by ACI committee 236, Material Science of Concrete. The 12 presentations from 8 different countries indicate...

  2. Deformation microstructures and mechanisms in the high-pressure granulites of the Bacariza Formation (Cabo Ortegal, NW Spain): going up to the surface

    Science.gov (United States)

    Puelles, P.; Abalos, B.

    2009-04-01

    The Cabo Ortegal complex is a nappe stack formed by fragments of subducted continental and oceanic lithosphere emplaced onto the Gondwana edge during the Variscan orogeny. The nappe units of Cabo Ortegal were metamorphosed under different high-pressure (HP) conditions and currently are separated by ductile tectonic contacts. They include mappable ultramafic massifs, N-MORB eclogites, metagabbros, metaserpentinites, metaperidotites, ortho- and paragneisses, and the Bacariza Formation granulites. The primary structure consists of the ultramafic massifs tectonically resting on top of the granulites of the Bacariza Formation, which overlie eclogites and HP gneisses with eclogite boudins. Granulites of the Bacariza Formation are mainly basic to intermediate in composition, although granulitic, carbonate-rich or mineralogically more exotic varieties also exist. On the basis of modal variations in the abundance of mafic and felsic mineral several lithotypes have been differentiated in order of decreasing outcrop area: (G1) plagio-pyrigarnites or common mafic granulites, (G2) intermediate to felsic, plagioclase-rich granulites, (G3) Mg-rich mafic granulites, (G4) pyrigarnite, or plagioclase-poor ultramafic granulites, and (G5) granulitic orthogneisses. The Bacariza Formation recorded a high-pressure metamorphic event. This event was polyphasic and two deformational phases are differentiated, D1 and D2, namely. D2 is associated to amalgamation of eclogite, high-pressure granulitic rocks and ultramafic sheets in deep portions of a subduction channel during the initial exhumation of the complex. As a result, transposition of the previous D1 fabrics took place due to the development of spectacular shear zones at the contacts with the bounding units. Pressure and temperature conditions estimated from the D2 mineral assemblage in equilibrium yield values of ca. 1.4 GPa and 740 °C, respectively. In this work we present a detailed study of a D2 shear zone located at the contact

  3. Effect of structural factors on mechanical properties of the magnesium alloy Ma2-1 under quasi-static and high strain rate deformation conditions

    Science.gov (United States)

    Garkushin, G. V.; Razorenov, S. V.; Krasnoveikin, V. A.; Kozulin, A. A.; Skripnyak, V. A.

    2015-02-01

    The elastic limit and tensile strength of deformed magnesium alloys Ma2-1 with different structures and textures were measured with the aim of finding a correlation between the spectrum of defects in the material and the resistance to deformation and fracture under quasi-static and dynamic loading conditions. The studies were performed using specimens in the as-received state after high-temperature annealing and specimens subjected to equal-channel angular pressing at a temperature of 250°C. The anisotropy of strength characteristics of the material after shock compression with respect to the direction of rolling of the original alloy was investigated. It was shown that, in contrast to the quasi-static loading conditions, under the shock wave loading conditions, the elastic limit and tensile strength of the magnesium alloy Ma2-1 after equal-channel angular pressing decrease as compared to the specimens in the as-received state.

  4. Characterization of intrabasin faulting and deformation for earthquake hazards in southern Utah Valley, Utah, from high-resolution seismic imaging

    Science.gov (United States)

    Stephenson, William J.; Odum, Jack K.; Williams, Robert A.; McBride, John H.; Tomlinson, Iris

    2012-01-01

    We conducted active and passive seismic imaging investigations along a 5.6-km-long, east–west transect ending at the mapped trace of the Wasatch fault in southern Utah Valley. Using two-dimensional (2D) P-wave seismic reflection data, we imaged basin deformation and faulting to a depth of 1.4 km and developed a detailed interval velocity model for prestack depth migration and 2D ground-motion simulations. Passive-source microtremor data acquired at two sites along the seismic reflection transect resolve S-wave velocities of approximately 200 m/s at the surface to about 900 m/s at 160 m depth and confirm a substantial thickening of low-velocity material westward into the valley. From the P-wave reflection profile, we interpret shallow (100–600 m) bedrock deformation extending from the surface trace of the Wasatch fault to roughly 1.5 km west into the valley. The bedrock deformation is caused by multiple interpreted fault splays displacing fault blocks downward to the west of the range front. Further west in the valley, the P-wave data reveal subhorizontal horizons from approximately 90 to 900 m depth that vary in thickness and whose dip increases with depth eastward toward the Wasatch fault. Another inferred fault about 4 km west of the mapped Wasatch fault displaces horizons within the valley to as shallow as 100 m depth. The overall deformational pattern imaged in our data is consistent with the Wasatch fault migrating eastward through time and with the abandonment of earlier synextensional faults, as part of the evolution of an inferred 20-km-wide half-graben structure within Utah Valley. Finite-difference 2D modeling suggests the imaged subsurface basin geometry can cause fourfold variation in peak ground velocity over distances of 300 m.

  5. Influence of deformation behavior, oxydation, and temperature on the long time cyclic stress behavior of high temperature steels

    Science.gov (United States)

    Maile, K.

    1982-01-01

    The influence of different parameters on the creep-fatigue behavior of several steel alloys was investigated. The higher the temperature the lower the crack initiation value. Pauses during the cycle reduce the damage. Oxidation reduces and protective gas increases the lifetime. Prior loading and prior deformation reduce the lifetime. Short annealing slightly affects the cycle stress behavior. The test results do not satisfactorily agree with methods of extrapolation and damage accumulation.

  6. Deformation of olivine-orthopyroxene aggregates at high pressure and temperature: Implications for the seismic properties of the asthenosphere

    Science.gov (United States)

    Soustelle, Vincent; Manthilake, Geeth

    2017-01-01

    The effect of pressure, temperature and composition on the development of crystal preferred orientations (CPO) and seismic properties of olivine-orthopyroxene aggregates were investigated using samples containing olivine and 12.5, 25 and 50 vol.% of orthopyroxene. The samples were deformed in simple-shear at a constant strain-rate of 10- 4 s- 1 with total shear strains between 0.5 and 1.3, at pressures of 3, 5 and 8 GPa and temperatures of 1300, 1400 and 1500 °C, respectively. Olivine's CPO vary as a function of the orthopyroxene content. All samples have their olivine [010] axes normal to the foliation. Samples with 12.5 and 25% orthopyroxene have their [001] axes parallel to the lineation (B-type), whereas the samples with 50% orthopyroxene have their [100] axes oriented parallel to the lineation (A-type). At 3 GPa, we propose that olivine CPO may result from a variation between two types of diffusion accommodated grain boundary sliding (difGBS) mechanisms. At higher pressure, the relative contribution of difGBS and dislocation related mechanisms depends on the volume of secondary phases. For low orthopyroxene contents, dislocation related mechanisms prevail and induce the development of B-type CPO, whereas for higher amount of orthopyroxene difGBS controls the deformation and leads to A-type CPO. Orthopyroxene's CPO strength increases with increasing pressure and temperature and is characterized by the concentration of [100] and [010] axes normal to the foliation and [001] close to the lineation. The seismic properties show that deformation in pyroxene-poor and rich peridotites are consistent with the seismic anisotropy observed in intraplate regions where the mantle flow is horizontal. Conversely, only pyroxene-rich peridotites deformed through difGBS could explain the Vsh/Vsv < 1 observed below mid-oceanic ridges.

  7. Constitutive Cyclic Deformation Behavior in Single-crystal and Directionally Solidified SSME High-pressure Fuel Turbopump Airfoil Materials

    Science.gov (United States)

    Milligan, W. W.; Huron, E. S.; Antolovich, S. D.

    1985-01-01

    The major goal of the project is to correlate mechanical properties with microstructural deformation behavior and to develop models for constitutive response under a variety of monotonic and cyclic loading cycles, temperatures, strain levels, strain rates, and environments. Two alloys are being studied as candidate SSME turbine blade materials. The first is PWA 1480, which is a single-crystal alloy whose nominal composition is reported. The second alloy being studied is D.S. Mar-M 246 + Hf. This is a directionally solidified material, and its nominal composition is also reported. The major areas of interest for the two materials will be slightly different. The single-crystal alloy lends itself well to fundamental deformation studies, since resolved shear stresses on slip planes are all known and only one grain is present. The D.S. material presents an excellent opportunity to study the effects of slightly misaligned grains on deformation behavior. The two materials will be studied by using approximately the same test matrix, so a good degree of direct comparison will also be possible.

  8. An elastic/viscoelastic finite element analysis method for crustal deformation using a 3-D island-scale high-fidelity model

    Science.gov (United States)

    Ichimura, Tsuyoshi; Agata, Ryoichiro; Hori, Takane; Hirahara, Kazuro; Hashimoto, Chihiro; Hori, Muneo; Fukahata, Yukitoshi

    2016-07-01

    As a result of the accumulation of high-resolution observation data, 3-D high-fidelity crustal structure data for large domains are becoming available. However, it has been difficult to use such data to perform elastic/viscoelastic crustal deformation analyses in large domains with quality assurance of the numerical simulation that guarantees convergence of the numerical solution with respect to the discretization size because the costs of analysis are significantly high. This paper proposes a method of constructing a high-fidelity crustal structure finite element (FE) model using high-fidelity crustal structure data and fast FE analysis to reduce the costs of analysis (based on automatic FE model generation for parallel computation, OpenMP/MPI hybrid parallel computation on distributed memory computers, a geometric multigrid, variable preconditioning and multiple precision arithmetic). Using the proposed methods, we construct 10 billion degree-of-freedom high-fidelity crustal structure FE models for the entire Japan, and conduct elastic/viscoelastic crustal deformation analysis using this model with enough high accuracy of the numerical simulation.

  9. Thermal stability of a highly-deformed warm-rolled tungsten plate in the temperature range 1100 °C to 1250 °C

    DEFF Research Database (Denmark)

    Alfonso Lopez, Angel; Juul Jensen, Dorte; Luo, G.-N.

    2015-01-01

    Pure tungsten is considered as armor material for the most critical parts of fusion reactors (i.e. the divertor and the first wall), among other reasons due to its high melting point (3422 °C) and recrystallization temperature. The thermal stability of a pure tungsten plate warm-rolled to a high...... suggest that large plastic deformations (e.g. applied during shaping) are only suitable to produce tungsten components to be used at relatively low temperatures (up to 900 °C for a 2 years lifespan). Higher operation temperatures will lead to fast degradation of the microstructure during operation....

  10. Insights into the deformation behavior of the CrMnFeCoNi high-entropy alloy revealed by elevated temperature nanoindentation

    Energy Technology Data Exchange (ETDEWEB)

    Maier-Kiener, Verena [Montanuniversitat Leoben, Leoben (Austria); Schuh, Benjamin [Austrian Academy of Sciences, Leoben (Austria); George, Easo P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Univ. of Tennessee, Knoxville, TN (United States); Clemens, Helmut [Montanuniversitat Leoben, Leoben (Austria); Hohenwarter, Anton [Austrian Academy of Sciences, Leoben (Austria)

    2017-07-27

    A CrMnFeCoNi high-entropy alloy was investigated by nanoindentation from room temperature to 400 °C in the nanocrystalline state and cast plus homogenized coarse-grained state. In the latter case a < 100 >-orientated grain was selected by electron back scatter diffraction for nanoindentation. It was found that hardness decreases more strongly with increasing temperature than Young’s modulus, especially for the coarse-grained state. The modulus of the nanocrystalline state was slightly higher than that of the coarse-grained one. For the coarse-grained sample a strong thermally activated deformation behavior was found up to 100–150 °C, followed by a diminishing thermally activated contribution at higher testing temperatures. For the nanocrystalline state, different temperature dependent deformation mechanisms are proposed. At low temperatures, the governing processes appear to be similar to those in the coarse-grained sample, but with increasing temperature, dislocation-grain boundary interactions likely become more dominant. Finally, at 400 °C, decomposition of the nanocrystalline alloy causes a further reduction in thermal activation. Furthermore, this is rationalized by a reduction of the deformation controlling internal length scale by precipitate formation in conjunction with a diffusional contribution.

  11. New High-Resolution 3D Seismic Imagery of Deformation and Fault Architecture Along Newport-Inglewood/Rose Canyon Fault in the Inner California Borderlands

    Science.gov (United States)

    Holmes, J. J.; Bormann, J. M.; Driscoll, N. W.; Kent, G.; Harding, A. J.; Wesnousky, S. G.

    2014-12-01

    The tectonic deformation and geomorphology of the Inner California Borderlands (ICB) records the transition from a convergent plate margin to a predominantly dextral strike-slip system. Geodetic measurements of plate boundary deformation onshore indicate that approximately 15%, or 6-8 mm/yr, of the total Pacific-North American relative plate motion is accommodated by faults offshore. The largest near-shore fault system, the Newport-Inglewood/Rose Canyon (NI/RC) fault complex, has a Holocene slip rate estimate of 1.5-2.0 mm/yr, according to onshore trenching, and current models suggest the potential to produce an Mw 7.0+ earthquake. The fault zone extends approximately 120 km, initiating from the south near downtown San Diego and striking northwards with a constraining bend north of Mt. Soledad in La Jolla and continuing northwestward along the continental shelf, eventually stepping onshore at Newport Beach, California. In late 2013, we completed the first high-resolution 3D seismic survey (3.125 m bins) of the NI/RC fault offshore of San Onofre as part of the Southern California Regional Fault Mapping project. We present new constraints on fault geometry and segmentation of the fault system that may play a role in limiting the extent of future earthquake ruptures. In addition, slip rate estimates using piercing points such as offset channels will be explored. These new observations will allow us to investigate recent deformation and strain transfer along the NI/RC fault system.

  12. Crustal deformation and gas emission from the Krýsuvík high temperature geothermal system, Iceland

    Science.gov (United States)

    Rakel Gudjonsdottir, Sylvia; Ilyinskaya, Evgenia; Hreinsdottir, Sigrun; Michakczewska, Karolina; Bergsson, Baldur; Auippa, Alessandro; Agla Oladottir, Audur; Rut Hjartardottir, Asta

    2016-04-01

    The Krýsuvík volcanic system is located at the oblique spreading Reykjanes Peninsula, Iceland. Since early 2009 the region has been undergoing episodes of localized ground uplift and subsidence. From March 2011 to the end of 2012 the region inflated by over 7 cm, triggering upper crustal earthquakes at the plate boundary. From 2012 to present the region has been subsiding at a relatively steady rate, reaching the pre inflation state by the end of 2015. GPS measurements indicate that the deflation source is located at 3 km depth coinciding with a previously mapped low resistivity zone from MT measurements suggesting the presence of water, magma or conductive minerals. In April 2013, near-real time monitoring of gas emissions started in Krýsuvík using a MultiGAS sensor system to collect data gas composition. Gas emissions are correlated with crustal deformation and seismicity within the Krýsuvík geothermal system. The dataset comprises near-continuous gas composition time series (MultiGAS); quantification of diffuse CO2 gas flux; direct samples of dry gas; seismic records; and GPS dataset. The gas emissions from the Krýsuvík system are H2O dominated with CO2 as the most abundant dry gas species, followed by lesser amounts of H2S. The subsurface equilibrium temperature is calculated as 278°C. This is consistent with previous observations made through sporadical sampling campaigns (e.g. Arnórsson, 1987). In addition, the semi-continuous MultiGAS dataset reveals higher variations of gas composition than previously reported by spot sampling. The diffuse CO2 soil flux is found to be variable between the three degassing areas in Krýsuvík ranging from 10.9-70.9 T/day with the highest flux in Hveradalir where the MultiGAS station is located. The total flux was calculated as 101.4 T/day. Correlation of the MultiGAS data with the geophysical data shows that peaks of H2O-rich emissions follow events of crustal movements. Coinciding with the H2O-rich peaks, SO2 is

  13. Evolution of deformation structures under varying loading conditions followed in situ by high angular resolution 3DXRD

    DEFF Research Database (Denmark)

    Pantleon, Wolfgang; Wejdemann, Christian; Jakobsen, B.;

    2009-01-01

    intermittently. When the traction is terminated, stress relaxation occurs and number, size and orientation of subgrains are found to be constant. The subgrain structure freezes and only a minor clean-up of the dislocation structure is observed. When changing the tensile direction after pre-deformation in tension......, a systematic correlation between the degree of strain path change and the changes in the dislocation structure quantified by the volume fraction of the subgrains is established. For obtaining the subgrain volume fraction, a new fitting method has been developed for partitioning the contributions of subgrains...

  14. Oscillatory thermocapillary convection in liquid bridges with highly deformed free surfaces: Experiments and energy-stability analysis

    Science.gov (United States)

    Sumner, L. B. S.; Neitzel, G. P.; Fontaine, J.-P.; Dell'Aversana, P.

    2001-01-01

    Laboratory experimentation, numerical simulation, and energy-stability theory are used to examine the effect of interface deformation on the onset of oscillatory thermocapillary convection in half zones. Experiments are performed to map the stability boundaries marking the onset of oscillatory flow, modifying the free-surface deformation by adjusting the volume of liquid in the bridge. The stability results presented here along with those of other researchers [Monti et al., Proceedings of the 43rd Cong. Int. Artro. Fed. (1992); Hu et al., J. Cryst. Growth 142, 379 (1994)] show that free-surface curvature can have a pronounced influence on flow stability. Steady, axisymmetric flow simulations are computed using the commercial code FIDAP to model the conditions of the experiments, and reveal that flow structure near the stability boundary is sensitive to several parameters. Energy theory is applied to these simulations to determine sufficient conditions for stability. Comparisons between the theoretical and experimental results show nonconservative energy limits falling above the experimentally determined stability boundaries for bridges of various liquid volumes. While the trend of the experimental data is predicted for zones of large volume ratio (bulging zones), the same cannot be said for those with small volume ratio (necked-down zones). In addition, energy-stability limits for some undeformed-free-surface cases were determined which are above the linear-stability limits determined by other researchers, in clear contradiction of the roles of the respective theories.

  15. Design, fabrication and characterization of high-stroke high-aspect ratio micro electro mechanical systems deformable mirrors for adaptive optics

    Science.gov (United States)

    Fernandez Rocha, Bautista

    Adaptive optic (AO) systems for next generation of extremely large telescopes (30--50 meter diameter primary mirrors) require high-stroke (10 microns), high-order (100x100) deformable mirrors at lower-cost than current technology. The required specifications are achievable with Micro Electro Mechanical Systems (MEMS) devices fabricated with high-aspect ratio processing techniques. This dissertation will review simulation results compared with displacement measurements of actuators utilizing a white-light interferometer. It will also review different actuator designs, materials and post-processing procedures fabricated in three different high-aspect ratio processes, Microfabrica's Electrochemical Fabrication (EFAB(TM)), HT-Micro's Precision Fabrication Technology (HTPF(TM)), and Innovative Micro Technologies (IMT) fabrication process. These manufacturing processes allow high-precision multilayer fabrication and their sacrificial layer thicknesses can be specified by the designer, rather than by constraints of the fabrication process. Various types of high-stroke gold actuators for AO consisting of folded springs with rectangular and circular membranes as well as X-beam actuators supported diagonally by beams were designed, simulated, fabricated, and tested individually and as part of a continuous facesheet DM system. The design, modeling and simulation of these actuators are compared to experimental measurements of their pull-in voltages, which characterizes their stiffness and maximum stroke. Vertical parallel plate ganged actuators fabricated with the EFAB(TM) process have a calculated pull-in voltage of 95V for a 600mum size device. In contrast, the pull-in voltages for the comb-drive actuators ranged from 55V for the large actuator, to 203V for the smallest actuator. Simulations and interferometer scans of actuator designs fabricated with HT-Micro's Precision Fabrication (HTPF(TM)) two wafer bonded process with different spring supports have shown the ability of

  16. Glacitectonic rafting and associated deformation of mid-Pleistocene glacigenic sediments, near Central Graben, central North Sea; results of a 2D High-Resolution Geophysical Survey

    Science.gov (United States)

    Vaughan-Hirsch, David

    2013-04-01

    transport for later stages of deformation, resulting in strike-slip basal detachment being associated with the later rafts. Localised distributions of high amplitude surfaces located adjacent to the primary detachment surface are identified through amplitude extraction techniques. These are indicative of migration and collection of gas along the inclined lower surfaces of rafted blocks. They represent a gas risk for drilling operations and demonstrate the significance and possible hazards of glacitectonic deformation to the exploration industry. A model for raft detachment and emplacement is proposed whereby; i) saturated sediments within the palaeo-channel are subject to pressurisation associated with overburden caused by over-riding ice, ii) elevated pore-water pressure develops along the principle detachment surface of the rafts, iii) early stages of deformation consist of ice-distal (southern) blocks becoming emplaced at relatively low angles of inclination, iv) with more proximal blocks accumulating as an imbricate thrust-stack sequence at relatively high angles of elevation. This interpretation suggests a significant subglacial hydrological control upon raft detachment and transport, with fluctuations between an extensional and compressive deformation regime caused by a switch from actively advancing glacial conditions to an oscillating ice-margin at this location. Tectono-stratigraphic evidence indicates that rafting occurring throughout the site is likely to be associated with a glacial advance of the Anglian (MIS 12).

  17. High strain-rate deformation fabrics characterize a kilometers-thick Paleozoic fault zone in the Eastern Sierras Pampeanas, central Argentina

    Science.gov (United States)

    Whitmeyer, Steven J.; Simpson, Carol

    2003-06-01

    High strain rate fabrics that transgress a crustal depth range of ca. 8-22 km occur within a major Paleozoic fault zone along the western margin of the Sierras de Córdoba, central Argentina. The NNW-striking, east-dipping 'Tres Arboles' fault zone extends for at least 250 km and separates two metamorphic terranes that reached peak temperatures in the middle Cambrian and Ordovician, respectively. Exposed fault zone rocks vary from a 16-km-thickness of ultramylonite and mylonite in the southern, deepest exposures to 520 °C. Reaction-enhanced grain size reduction and grain boundary sliding were the predominant deformation mechanisms in these high strain rate rocks. Ultramylonites in the intermediate depth section also contain evidence for grain boundary sliding and diffusional mass transfer, although overprinted by late stage chlorite. In the shallowest exposed section, rocks were deformed at or near to the brittle-ductile transition to produce mylonite, cataclasite, shear bands and pseudotachylyte. The overall structure of the Tres Arboles zone is consistent with existing fault zone models and suggests that below the brittle-ductile transition, strain compatibility may be accommodated through very thick zones of high temperature ultramylonite.

  18. COMPUTER MODELING IN DEFORM-3D FOR ANALYSIS OF PLASTIC FLOW IN HIGH-SPEED HOT EXTRUSION OF BIMETALLIC FORMATIVE PARTS OF DIE TOOLING

    Directory of Open Access Journals (Sweden)

    I. V. Kachanov

    2015-01-01

    Full Text Available The modern development of industrial production is closely connected with the use of science-based and high technologies to ensure competitiveness of the manufactured products on the world market. There is also much tension around an energy- and resource saving problem which can be solved while introducing new technological processes and  creation of new materials that provide productivity increase through automation and improvement of tool life. Development and implementation of such technologies are rather often considered as time-consuming processes  which are connected with complex calculations and experimental investigations. Implementation of a simulation modelling for materials processing using modern software products serves an alternative to experimental and theoretical methods of research.The aim of this paper is to compare experimental results while obtaining bimetallic samples of a forming tool through the method of speed hot extrusion and the results obtained with the help of computer simulation using DEFORM-3D package and a finite element method. Comparative analysis of plastic flow of real and model samples has shown that the obtained models provide high-quality and reliable picture of plastic flow during high-speed hot extrusion. Modeling in DEFORM-3D make it possible to eliminate complex calculations and significantly reduce a number of experimental studies while developing new technological processes.

  19. 2012 ROCK DEFORMATION: FEEDBACK PROCESSES IN ROCK DEFORMATION GORDON RESEARCH CONFERENCE, AUGUST 19-24, 2012

    Energy Technology Data Exchange (ETDEWEB)

    Kelemen, Peter

    2012-08-24

    Topics covered include: Failure At High Confining Pressure; Fluid-assisted Slip, Earthquakes & Fracture; Reaction-driven Cracking; Fluid Transport, Deformation And Reaction; Localized Fluid Transport And Deformation; Earthquake Mechanisms; Subduction Zone Dynamics And Crustal Growth.

  20. DISLOCATION PINNING IN HIGH TEMPERATURE DEFORMED Ni3(Al,Ti) SINGLE CRYSTALS CONTAINING DISORDERED γ PRECIPITATES

    Institute of Scientific and Technical Information of China (English)

    W.H. Tian; M. Nemoto

    2006-01-01

    A transmission electron microscopy (TEM) investigation has been performed on the dislocation pinning in LI2-ordered Ni3(Al, Ti) containing disordered γ precipitates. The morphology of deformation induced dislocations in the γ' base alloys containing fine dispersion of disordered γ was investigated by means of weak-beam electron microscopy. The superdislocations are strongly attracted to the disordered particles and dissociate on the (111) plane in the γ particles, while they dissociate on the (010) plane in the γ' matrix. The disordered γ precipitates play an important role as a pinning point during the cross-slip of superdislocations from (111) to (010) planes in the γ'matrix and restrain the cross-slip of superdislocations. The interaction of superdislocations with disordered particles causes the formation of superkinks, jogs and closed loops.

  1. High-Temperature In situ Deformation of GaAs Micro-pillars: Lithography Versus FIB Machining

    Science.gov (United States)

    Chen, M.; Wehrs, J.; Michler, J.; Wheeler, J. M.

    2016-11-01

    The plasticity of silicon-doped GaAs was investigated between 25°C and 400°C using microcompression to prevent premature failure by cracking. Micropillars with diameters of 2.5 μm were fabricated on a < 100rangle -oriented GaAs single crystal by means of both conventional lithographic etching techniques and focused ion beam machining and then compressed in situ in the scanning electron microscope (SEM). A transition in deformation mechanisms from partial dislocations to perfect dislocations was found at around 100°C. At lower temperatures, the residual surface layer from lithographic processing was found to provide sufficient constraint to prevent crack opening, which resulted in a significant increase in ductility over FIB-machined pillars. Measured apparent activation energies were found to be significantly lower than previous bulk measurements, which is mostly attributed to the silicon dopant and to a lesser extent to the size effect.

  2. 矿区高精度GPS地表变形监测体系%High-precision surface deformation monitoring system with GPS in mining area

    Institute of Scientific and Technical Information of China (English)

    张敬霞; 刘超; 龙仁波; 王建鹏

    2013-01-01

    文章针对地表起伏较大或沟壑林立的矿区,引入GPS技术,建立了GPS矿区地表变形监测体系,结合具体的矿山生产案例,给出了该体系的基本技术流程及其数据结果,验证了采用GPS技术进行矿区高精度地表变形监测的可行性;建立了高精度三维变形监测基准网和区域似大地水准面模型,为矿区高精度正常高的快速获取以及多源变形数据的融合提供了有效的技术支持;以矿区地表变形规律的获取和高精度井塔实时动态监测为应用案例,说明了该监测体系的有效性.%In view of the variability of mine surfaces,global positioning system(GPS) technique is employed to establish the dynamic deformation monitoring system in mine area.Based on the productive practice in two coal mines,basic procedures of the system and detailed process of data processing are presented in order to verify the possibility of high-precision subsidence monitoring in mining area with GPS.High-precision 3D GPS control network and quasi-geoid model are constructed to offer the technical support for quickly acquiring the high-precision normal height and integrating the multi-source deformation data in mining area.Based on the deformation data measured by GPS,the surface movement and displacement law,surface movement parameters and shaft tower deformation can be obtained,showing the effectiveness of the monitoring system.

  3. Influence of high-pressure deformation and annealing on the structure and properties of a bulk MgB2 superconductor

    Science.gov (United States)

    Degtyarev, M. V.; Pilyugin, V. P.; Akshentsev, Yu. N.; Kuznetsova, E. I.; Krinitsina, T. P.; Blinova, Yu. V.; Sudareva, S. V.; Romanov, E. P.

    2016-08-01

    A synthesized MgB2 superconductor has been investigated by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and by the measurements of the superconducting characteristics and microhardness after cold high-pressure deformation in a Toroid chamber and in Bridgman anvils and subsequent high-temperature annealing. A nanocrystalline structure is formed in the superconductor after high-pressure treatment, but internal cracks appear, and the critical current density decreases strongly. The annealing leads to a coarsening of the structure and to an increase in the critical current density up to 5.8-6.7 × 104 A/cm2, which is more than three times greater than that in the initial state.

  4. Low-Temperature Nitriding of Deformed Austenitic Stainless Steels with Various Nitrogen Contents Obtained by Prior High-Temperature Solution Nitriding

    Science.gov (United States)

    Bottoli, Federico; Winther, Grethe; Christiansen, Thomas L.; Dahl, Kristian Vinter; Somers, Marcel A. J.

    2016-08-01

    In the past decades, high nitrogen steels (HNS) have been regarded as substitutes for conventional austenitic stainless steels because of their superior mechanical and corrosion properties. However, the main limitation to their wider application is their expensive production process. As an alternative, high-temperature solution nitriding has been applied to produce HNS from three commercially available stainless steel grades (AISI 304L, AISI 316, and EN 1.4369). The nitrogen content in each steel alloy is varied and its influence on the mechanical properties and the stability of the austenite investigated. Both hardness and yield stress increase and the alloys remain ductile. In addition, strain-induced transformation of austenite to martensite is suppressed, which is beneficial for subsequent low-temperature nitriding of the surface of deformed alloys. The combination of high- and low-temperature nitriding results in improved properties of both bulk and surface.

  5. LASS U-Th-Pb monazite and rutile geochronology of felsic high-pressure granulites (Rhodope, N Greece): Effects of fluid, deformation and metamorphic reactions in local subsystems

    Science.gov (United States)

    Wawrzenitz, Nicole; Krohe, Alexander; Baziotis, Ioannis; Mposkos, Evripidis; Kylander-Clark, Andrew R. C.; Romer, Rolf L.

    2015-09-01

    The specific chemical composition of monazite in shear zones is controlled by the syndeformation dissolution-precipitation reactions of the rock-forming minerals. This relation can be used for dating deformation, even when microfabric characteristics like shape preferred orientation or intracrystalline deformation of monazite itself are missing. Monazite contemporaneously formed in and around the shear zones may have different compositions. These depend on the local chemical context rather than reflecting successive crystallization episodes of monazite. This is demonstrated in polymetamorphic, mylonitic high-pressure (HP) garnet-kyanite granulites of the Alpine Sidironero Complex (Rhodope UHP terrain, Northern Greece). The studied mylonitic rocks escaped from regional migmatization at 40-36 Ma and from subsequent shearing through cooling until 36 Ma. In-situ laser-ablation split-stream inductively-coupled plasma mass spectrometry (LASS) analyses have been carried out on monazite from micro-scale shear zones, from pre-mylonitic microlithons as well as of monazite inclusions in relictic minerals complimented by U-Pb data on rutile and Rb-Sr data of biotite. Two major metamorphic episodes, Mesozoic and Cenozoic, are constrained. Chemical compositions, isotopic characteristics and apparent ages systematically vary among monazite of four different microfabric domains (I-IV). Within three pre-mylonitic domains (inclusions in (I) pre-mylonitic kyanite and (II) garnet porphyroclasts, and (III) in pre-mylonitic microlithons) monazite yields ages of ca. 130-150 Ma for HP-granulite metamorphism, in line with previous geochronological results in the area. Patchy alteration of the pre-mylonitic monazite by intra-grain dissolution-precipitation processes variably increased negative Eu anomaly and reduced the HREE contents. The apparent age of this altered monazite is reduced. Monazite in the syn-mylonitic shear bands (IV) differs in chemical composition from unaltered and

  6. Plastic Deformation of Metal Surfaces

    DEFF Research Database (Denmark)

    Hansen, Niels; Zhang, Xiaodan; Huang, Xiaoxu

    2013-01-01

    parameters by TEM and EBSD and apply strength-structural relationships established for the bulk metal deformed to high strains. This technique has been applied to steel deformed by high energy shot peening and a calculated stress gradient at or near the surface has been successfully validated by hardness......Plastic deformation of metal surfaces by sliding and abrasion between moving parts can be detrimental. However, when the plastic deformation is controlled for example by applying different peening techniques hard surfaces can be produced which can increase the fracture resistance and fatigue life...... of metal components. An optimization of processes and material parameters must be based on a quantification of stress and strain gradients at the surface and in near surface layer where the structural scale can reach few tens of nanometers. For such fine structures it is suggested to quantify structural...

  7. Inelastic deformation in crystalline rocks

    Science.gov (United States)

    Rahmani, H.; Borja, R. I.

    2011-12-01

    The elasto-plastic behavior of crystalline rocks, such as evaporites, igneous rocks, or metamorphic rocks, is highly dependent on the behavior of their individual crystals. Previous studies indicate that crystal plasticity can be one of the dominant micro mechanisms in the plastic deformation of crystal aggregates. Deformation bands and pore collapse are examples of plastic deformation in crystalline rocks. In these cases twinning within the grains illustrate plastic deformation of crystal lattice. Crystal plasticity is governed by the plastic deformation along potential slip systems of crystals. Linear dependency of the crystal slip systems causes singularity in the system of equations solving for the plastic slip of each slip system. As a result, taking the micro-structure properties into account, while studying the overall behavior of crystalline materials, is quite challenging. To model the plastic deformation of single crystals we use the so called `ultimate algorithm' by Borja and Wren (1993) implemented in a 3D finite element framework to solve boundary value problems. The major advantage of this model is that it avoids the singularity problem by solving for the plastic slip explicitly in sub steps over which the stress strain relationship is linear. Comparing the results of the examples to available models such as Von Mises we show the significance of considering the micro-structure of crystals in modeling the overall elasto-plastic deformation of crystal aggregates.

  8. Perceptual transparency from image deformation.

    Science.gov (United States)

    Kawabe, Takahiro; Maruya, Kazushi; Nishida, Shin'ya

    2015-08-18

    Human vision has a remarkable ability to perceive two layers at the same retinal locations, a transparent layer in front of a background surface. Critical image cues to perceptual transparency, studied extensively in the past, are changes in luminance or color that could be caused by light absorptions and reflections by the front layer, but such image changes may not be clearly visible when the front layer consists of a pure transparent material such as water. Our daily experiences with transparent materials of this kind suggest that an alternative potential cue of visual transparency is image deformations of a background pattern caused by light refraction. Although previous studies have indicated that these image deformations, at least static ones, play little role in perceptual transparency, here we show that dynamic image deformations of the background pattern, which could be produced by light refraction on a moving liquid's surface, can produce a vivid impression of a transparent liquid layer without the aid of any other visual cues as to the presence of a transparent layer. Furthermore, a transparent liquid layer perceptually emerges even from a randomly generated dynamic image deformation as long as it is similar to real liquid deformations in its spatiotemporal frequency profile. Our findings indicate that the brain can perceptually infer the presence of "invisible" transparent liquids by analyzing the spatiotemporal structure of dynamic image deformation, for which it uses a relatively simple computation that does not require high-level knowledge about the detailed physics of liquid deformation.

  9. Occurrence of oral deformities in larval anurans

    Science.gov (United States)

    Drake, D.L.; Altig, R.; Grace, J.B.; Walls, S.C.

    2007-01-01

    We quantified deformities in the marginal papillae, tooth rows, and jaw sheaths of tadpoles from 13 population samples representing three families and 11 sites in the southeastern United States. Oral deformities were observed in all samples and in 13.5-98% of the specimens per sample. Batrachochytrium dendrobatidis (chytrid) infections were detected in three samples. There was high variability among samples in the pattern and number of discovered deformities. Pairwise associations between oral structures containing deformities were nonrandom for several populations, especially those with B. dendrobatidis infections or high total numbers of deformities. Comparisons of deformities among samples using multivariate analyses revealed that tadpole samples grouped together by family. Analyses of ordination indicated that three variables, the number of deformities, the number of significant associations among deformity types within populations, and whether populations were infected with B. dendrobatidis, were significantly correlated with the pattern of deformities. Our data indicate that the incidence of oral deformities can be high in natural populations and that phylogeny and B. dendrobatidis infection exert a strong influence on the occurrence and type of oral deformities in tadpoles. ?? by the American Society of Ichthyologists and Herperologists.

  10. Loop-deformed Poincar\\'e algebra

    CERN Document Server

    Mielczarek, Jakub

    2013-01-01

    In this essay we present evidence suggesting that loop quantum gravity leads to deformation of the local Poincar\\'e algebra within the limit of high energies. This deformation is a consequence of quantum modification of effective off-shell hypersurface deformation algebra. Surprisingly, the form of deformation suggests that the signature of space-time changes from Lorentzian to Euclidean at large curvatures. We construct particular realization of the loop-deformed Poincar\\'e algebra and find that it can be related to curved momentum space, which indicates the relationship with recently introduced notion of relative locality. The presented findings open a new way of testing loop quantum gravity effects.

  11. Insights on high-grade deformation in quartzo-feldspathic gneisses during the early Variscan exhumation of the Cabo Ortegal nappe, NW Iberia

    Science.gov (United States)

    José Fernández, Francisco; Llana-Fúnez, Sergio; Valverde-Vaquero, Pablo; Marcos, Alberto; Castiñeiras, Pedro

    2016-04-01

    High-grade, highly deformed gneisses crop out continuously along the Masanteo peninsula and constitute the upper part of the lower crustal section in the Cabo Ortegal nappe (NW Spain). The rock sequence formed by migmatitic quartzo-feldspathic (qz-fsp) gneisses and mafic rocks records the early Ordovician (ca. 480-488 Ma) injection of felsic dioritic/granodioritic dykes at the base of the qz-fsp gneisses, and Devonian eclogitization (ca. 390.4 ± 1.2 Ma), prior to its exhumation. A SE-vergent ductile thrust constitutes the base of quartzo-feldspathic gneissic unit, incorporating mafic eclogite blocks within migmatitic gneisses. A NW-vergent detachment displaced metasedimentary qz-fsp gneisses over the migmatites. A difference in metamorphic pressure of ca. 0.5 GPa is estimated between both gneissic units. The tectono-metamorphic relationships of the basal ductile thrust and the normal detachment bounding the top of the migmatites indicate that both discrete mechanical contacts were active before the recumbent folding affecting the sequence of gneisses during their final emplacement. The progressive tectonic exhumation from eclogite to greenschist facies conditions occurred over ca. 10 Ma and involved bulk thinning of the high-grade rock sequence in the high pressure and high temperature (HP-HT) Cabo Ortegal nappe. The necessary strain was accommodated by the development of a widespread main foliation, dominated by flattening, that subsequently localized to a network of anastomosing shear bands that evolved to planar shear zones. Qz-fsp gneisses and neighbouring mafic granulites were exhumed at > 3 mm yr-1, and the exhumation path involved a cooling of ˜ 20 °C/100 MPa, These figures are comparable to currently active subduction zones, although exhumation P-T trajectory and ascent rates are at the hotter and slower end in comparison with currently active similar settings, suggesting an extremely ductile deformation environment during the exhumation of qz

  12. Mechanical Properties and Microstructure Evolution of Cold-deformed High-nitrogen Nickel-free Austenitic Stainless Steel during Annealing

    Institute of Scientific and Technical Information of China (English)

    XU Mingzhou; WANG Jianjun; LIU Chunming

    2012-01-01

    The mechanical properties and microstructure evolution of cold-deformed CrMnN austenitic stainless steel annealed in a temperature ranging from 50 ℃ to 650 ℃ for 90 min and at 550 ℃ for different time were investigated by tensile test,micro hardness test,and Transmission Electron Microscope (TEM).The steel was strengthened when it got annealed at temperatures ranging from 100 ℃ to 550 ℃,while it was softened when it got annealed at temperatures ranging from 550 ℃ to 650 ℃.Annealing temperature had stronger effect on mechanical properties than annealing time.TEM observations showed that nano-sized precipitates formed when the steel was annealed at 150 ℃ for 90 min,but the size and density of precipitates had no noticeable change with annealing temperature and time.Recrystallization occurred when the steel was annealed at temperatures above 550 ℃ for 90 min,and its scale increased with annealing temperature.Nanosized annealing twins were observed.The mechanisms that controlled the mechanical behaviors of the steel were discussed.

  13. Mechanical characterization and modeling of the deformation and failure of the highly crosslinked RTM6 epoxy resin

    Science.gov (United States)

    Morelle, X. P.; Chevalier, J.; Bailly, C.; Pardoen, T.; Lani, F.

    2017-01-01

    The nonlinear deformation and fracture of RTM6 epoxy resin is characterized as a function of strain rate and temperature under various loading conditions involving uniaxial tension, notched tension, uniaxial compression, torsion, and shear. The parameters of the hardening law depend on the strain-rate and temperature. The pressure-dependency and hardening law, as well as four different phenomenological failure criteria, are identified using a subset of the experimental results. Detailed fractography analysis provides insight into the competition between shear yielding and maximum principal stress driven brittle failure. The constitutive model and a stress-triaxiality dependent effective plastic strain based failure criterion are readily introduced in the standard version of Abaqus, without the need for coding user subroutines, and can thus be directly used as an input in multi-scale modeling of fibre-reinforced composite material. The model is successfully validated against data not used for the identification and through the full simulation of the crack propagation process in the V-notched beam shear test.

  14. Mechanical characterization and modeling of the deformation and failure of the highly crosslinked RTM6 epoxy resin

    Science.gov (United States)

    Morelle, X. P.; Chevalier, J.; Bailly, C.; Pardoen, T.; Lani, F.

    2017-08-01

    The nonlinear deformation and fracture of RTM6 epoxy resin is characterized as a function of strain rate and temperature under various loading conditions involving uniaxial tension, notched tension, uniaxial compression, torsion, and shear. The parameters of the hardening law depend on the strain-rate and temperature. The pressure-dependency and hardening law, as well as four different phenomenological failure criteria, are identified using a subset of the experimental results. Detailed fractography analysis provides insight into the competition between shear yielding and maximum principal stress driven brittle failure. The constitutive model and a stress-triaxiality dependent effective plastic strain based failure criterion are readily introduced in the standard version of Abaqus, without the need for coding user subroutines, and can thus be directly used as an input in multi-scale modeling of fibre-reinforced composite material. The model is successfully validated against data not used for the identification and through the full simulation of the crack propagation process in the V-notched beam shear test.

  15. The effect of high temperature plastic deformation on the thermal stability and microstructure of Zr{sub 55}Cu{sub 30}Ni{sub 5}Al{sub 10} bulk metallic glass

    Energy Technology Data Exchange (ETDEWEB)

    Liu, L. [State Key Lab of Die and Mould Technology, Huazhong University of Science and Technology, 430074 Wuhan (China)], E-Mail: lliu2000@public.wh.hb.cn; Chen, Q. [State Key Lab of Die and Mould Technology, Huazhong University of Science and Technology, 430074 Wuhan (China); Chan, K.C. [Department of Industrial and Systems Engineering, Hong Kong Polytechnic University, Hong Kong (China); Wang, J.F. [State Key Lab of Die and Mould Technology, Huazhong University of Science and Technology, 430074 Wuhan (China); Pang, G.K.H. [Department of Applied Physics, The Hong Kong Polytechnic University, Hong Kong (China)

    2007-03-25

    The plastic deformation of Zr{sub 55}Cu{sub 30}Al{sub 10}Ni{sub 5} (numbers indicate at.%) bulk metallic glass (BMG) was conducted in the supercooled liquid region under uniaxial tension with various strain rates ranging from 8.3 x 10{sup -4} to 2 x 10{sup -2} s{sup -1}. It was found that the deformation behavior of the BMG is strongly dependent on strain rate. Thermal and structural investigations revealed that the plastic deformation reduced the thermal stability of Zr{sub 55}Cu{sub 30}Al{sub 10}Ni{sub 5} BMG and promoted crystallization or reordering of the amorphous structure. To clarify the correlation between strain and structure of the BMG, the sample that was deformed at a high strain rate and exhibited significant necking was selected for a detailed investigation of its structure in different parts (e.g., the tip, middle and end parts) by conventional and high-resolution transmission electron microscopy. It was found that a band crystalline structure with a strongly crystallographic orientation was formed at the tip part, while inhomogeneous nanocrystallization occurred in the middle parts, and the amorphous structure remained almost unchanged in the end part. The different structures observed in different parts of the deformed sample are attributed to the inhomogeneous deformation of the BMG at high strain rates.

  16. Paramagnetic susceptibility of the Zr62Cu22Al10Fe5Dy1 metallic glass subjected to high-pressure torsion deformation

    Science.gov (United States)

    Korolev, A. V.; Kourov, N. I.; Pushin, V. G.; Gunderov, D. V.; Boltynjuk, E. V.; Ubyivovk, E. V.; Valiev, R. Z.

    2017-09-01

    The Zr62Cu22Al10Fe5Dy1 bulk metallic glass is studied in the as-cast state and in the state after processing by high-pressure torsion at temperatures of 20 °C and 150 °C. According to the data from X-ray diffraction and transmission electron microscopy, the structural state of the samples depends weakly on the conducted processing. At the same time, magnetic measurements reveal well recordable changes in paramagnetic susceptibility induced by the processing of the samples. It is assumed that, because of high-pressure torsion deformation, there occurs a noticeable change in the material electronic structure, which leads to a change in the full susceptibility of the samples. The performed studies demonstrate that paramagnetic susceptibility may be an indicator of a change in the structural state of paramagnetic amorphous metallic substances.

  17. Micromechanics of plastic deformation and phase transformation in a three-phase TRIP-assisted advanced high strength steel: Experiments and modeling

    Science.gov (United States)

    Srivastava, Ankit; Ghassemi-Armaki, Hassan; Sung, Hyokyung; Chen, Peng; Kumar, Sharvan; Bower, Allan F.

    2015-05-01

    The micromechanics of plastic deformation and phase transformation in a three-phase advanced high strength steel are analyzed both experimentally and by microstructure-based simulations. The steel examined is a three-phase (ferrite, martensite and retained austenite) quenched and partitioned sheet steel with a tensile strength of ~980 MPa. The macroscopic flow behavior and the volume fraction of martensite resulting from the austenite-martensite transformation during deformation were measured. In addition, micropillar compression specimens were extracted from the individual ferrite grains and the martensite particles, and using a flat-punch nanoindenter, stress-strain curves were obtained. Finite element simulations idealize the microstructure as a composite that contains ferrite, martensite and retained austenite. All three phases are discretely modeled using appropriate crystal plasticity based constitutive relations. Material parameters for ferrite and martensite are determined by fitting numerical predictions to the micropillar data. The constitutive relation for retained austenite takes into account contributions to the strain rate from the austenite-martensite transformation, as well as slip in both the untransformed austenite and product martensite. Parameters for the retained austenite are then determined by fitting the predicted flow stress and transformed austenite volume fraction in a 3D microstructure to experimental measurements. Simulations are used to probe the role of the retained austenite in controlling the strain hardening behavior as well as internal stress and strain distributions in the microstructure.

  18. Measurement of Surface Displacement and Deformation of Mass Movements Using Least Squares Matching of Repeat High Resolution Satellite and Aerial Images

    Directory of Open Access Journals (Sweden)

    Misganu Debella-Gilo

    2012-01-01

    Full Text Available Displacement and deformation are fundamental measures of Earth surface mass movements such as glacier flow, rockglacier creep and rockslides. Ground-based methods of monitoring such mass movements can be costly, time consuming and limited in spatial and temporal coverage. Remote sensing techniques, here matching of repeat optical images, are increasingly used to obtain displacement and deformation fields. Strain rates are usually computed in a post-processing step based on the gradients of the measured velocity field. This study explores the potential of automatically and directly computing velocity, rotation and strain rates on Earth surface mass movements simultaneously from the matching positions and the parameters of the geometric transformation models using the least squares matching (LSM approach. The procedures are exemplified using bi-temporal high resolution satellite and aerial images of glacier flow, rockglacier creep and land sliding. The results show that LSM matches the images and computes longitudinal strain rates, transverse strain rates and shear strain rates reliably with mean absolute deviations in the order of 10−4 (one level of significance below the measured values as evaluated on stable grounds. The LSM also improves the accuracy of displacement estimation of the pixel-precision normalized cross-correlation by over 90% under ideal (simulated circumstances and by about 25% for real multi-temporal images of mass movements.

  19. Highly oriented NdFeB nanocrystalline magnets from partially recombined compacts with ultrafine grain size by reactive deformation under low pressure

    Institute of Scientific and Technical Information of China (English)

    余云萍; 李军; 刘颖; 王仁全; 郑青; 连利仙

    2015-01-01

    The partially recombined compacts with ultrafine grain size were taken advantage of preparing anisotropic nanocrystalline magnets with full density and homogenous microstructure and texture by reactive deformation under low pressure. Because of the ul-trafine grain size of the precursors, the partially recombined phases could quickly achieve recombination. The results suggested that the newly recombined Nd2Fe14B grains with fine grain size could undergo deformation immediately during the desorp-tion-recombination reaction, and then an obvious anisotropy and uniform alignment would be obtained. The magnetic properties, (BH)max=214 kJ/m3,Br= 1.26 T,Hcj=463 kA/m, were obtained after being treated for 5 min at 820 ºC in high vacuum under low pres-sure less than 26 MPa. Microstructures of the magnets were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) respectively. Magnetic measurements were carried out using a vibrating sample magnetometer (VSM) with the maximum field of 2.88 T. Accurate phase contents were measured by a Mossbauer spectrometer.

  20. High-grade deformation in quartzo-feldspathic gneisses during the early Variscan exhumation of the Cabo Ortegal nappe, NW of Iberia

    Directory of Open Access Journals (Sweden)

    F. J. Fernández

    2015-12-01

    Full Text Available High-grade highly deformed gneisses crop out continuously along the Masanteo peninsula in the Cabo Ortegal nappe (NW Spain. The rock sequence formed by quartzo-feldspathic gneisses and mafic rocks records two partial melting events: during the Early Ordovician (ca. 480–488 Ma., at the base of the Qz-Fsp gneisses, and immediately after eclogization (ca. 390.4 ± 1.2 Ma, during its early Variscan exhumation. Despite the strain accumulated during their final exhumation in which a pervasive blastomylonitic S2 foliation was developed, primary sedimentary layering in Qz-Fsp gneisses is well preserved locally at the top of the sequence. This first stage of the exhumation process occurred in ~ 10 Ma, during which bulk flattening of the high-grade rock sequence was accommodated by anastomosing shear bands that evolved to planar shear zones. Strain was progressively localized along the boundaries of the migmatitic Qz-Fsp gneisses. A SE-vergent ductile thrust constitutes the base of gneisses, incorporating eclogite blocks-in-matrix. A NW-vergent detachment placed the metasedimentary Qz-Fsp gneisses over the migmatitic Qz-Fsp gneisses. A difference in metamorphic pressure of ca. 0.5 GPa is estimated between both gneissic units. The high-grade deformation reduced substantially the thickness of the gneissic rock sequence during the process of exhumation controlled by change in the strain direction and the progressive localization of strain. The combined movement of the top detachment and basal thrust resulted in an extrusion of the migmatites within the nappe, directed to the SE in current coordinates.

  1. Recrystallization of deformed copper - kinetics and microstructural evolution

    DEFF Research Database (Denmark)

    Lin, Fengxiang

    The objective of this study is to investigate the recrystallization kinetics and microstructural evolution in copper deformed to high strains, including copper deformed by cold-rolling and copper deformed by dynamic plastic deformation (DPD). Various characterization techniques were used, including...

  2. Deformed two center shell model

    CERN Document Server

    Gherghescu, R A

    2003-01-01

    A highly specialized two-center shell model has been developed accounting for the splitting of a deformed parent nucleus into two ellipsoidaly deformed fragments. The potential is based on deformed oscillator wells in direct correspondance with the shape change of the nuclear system. For the first time a potential responsible for the necking part between the fragments is introduced on potential theory basis. As a direct consequence, spin-orbit {\\bf ls} and {\\bf l$^2$} operators are calculated as shape dependent. Level scheme evolution along the fission path for pairs of ellipsoidaly deformed fragments is calculated. The Strutinsky method yields the shell corrections for different mass asymmetries from the superheavy nucleus $^{306}$122 and $^{252}$Cf all along the splitting process.

  3. Helium release during shale deformation: Experimental validation

    Science.gov (United States)

    Bauer, Stephen J.; Gardner, W. Payton; Heath, Jason E.

    2016-07-01

    This work describes initial experimental results of helium tracer release monitoring during deformation of shale. Naturally occurring radiogenic 4He is present in high concentration in most shales. During rock deformation, accumulated helium could be released as fractures are created and new transport pathways are created. We present the results of an experimental study in which confined reservoir shale samples, cored parallel and perpendicular to bedding, which were initially saturated with helium to simulate reservoir conditions, are subjected to triaxial compressive deformation. During the deformation experiment, differential stress, axial, and radial strains are systematically tracked. Release of helium is dynamically measured using a helium mass spectrometer leak detector. Helium released during deformation is observable at the laboratory scale and the release is tightly coupled to the shale deformation. These first measurements of dynamic helium release from rocks undergoing deformation show that helium provides information on the evolution of microstructure as a function of changes in stress and strain.

  4. Nanoscale Deformable Optics

    Science.gov (United States)

    Strauss, Karl F.; Sheldon, Douglas J.

    2011-01-01

    Several missions and instruments in the conceptual design phase rely on the technique of interferometry to create detectable fringe patterns. The intimate emplacement of reflective material upon electron device cells based upon chalcogenide material technology permits high-speed, predictable deformation of the reflective surface to a subnanometer or finer resolution with a very high degree of accuracy. In this innovation, a layer of reflective material is deposited upon a wafer containing (perhaps in the millions) chalcogenic memory cells with the reflective material becoming the front surface of a mirror and the chalcogenic material becoming a means of selectively deforming the mirror by the application of heat to the chalcogenic material. By doing so, the mirror surface can deform anywhere from nil to nanometers in spots the size of a modern day memory cell, thereby permitting realtime tuning of mirror focus and reflectivity to mitigate aberrations caused elsewhere in the optical system. Modern foundry methods permit the design and manufacture of individual memory cells having an area of or equal to the Feature (F) size of the design (assume 65 nm). Fabrication rules and restraints generally require the instantiation of one memory cell to another no closer than 1.5 F, or, for this innovation, 90 nm from its neighbor in any direction. Chalcogenide is a semiconducting glass compound consisting of a combination of chalcogen ions, the ratios of which vary according to properties desired. It has been shown that the application of heat to cells of chalcogenic material cause a large alteration in resistance to the range of 4 orders of magnitude. It is this effect upon which chalcogenidebased commercial memories rely. Upon removal of the heat source, the chalcogenide rapidly cools and remains frozen in the excited state. It has also been shown that the chalcogenide expands in volume because of the applied heat, meaning that the coefficient of expansion of chalcogenic

  5. Close-loop performance of a high precision deflectometry controlled deformable mirror (DCDM) unit for wavefront correction in adaptive optics system

    Science.gov (United States)

    Huang, Lei; Zhou, Chenlu; Zhao, Wenchuan; Choi, Heejoo; Graves, Logan; Kim, Daewook

    2017-06-01

    We present a high precision deflectometry system (DS) controlled deformable mirror (DM) solution for optical system. Different from wavefront and non-wavefront system, the DS and the DM are set to be an individual integrated DCDM unit and can be installed in one base plate. In the DCDM unit, the DS can directly provide the influence functions and surface shape of the DM to the industrial computer in any adaptive optics system. As an integrated adaptive unit, the DCDM unit could be put into various optical systems to realize aberration compensation. In this paper, the configuration and principle of the DCDM unit is introduced first. Theoretical simulation on the close-loop performance of the DCDM unit is carried out. Finally, a verification experiment is proposed to verify the compensation capability of the DCDM unit.

  6. Research on sub-surface damage and its stress deformation in the process of large aperture and high diameter-to-thickness ratio TMT M3MP

    Science.gov (United States)

    Hu, Hai-xiang; Qi, Erhui; Cole, Glen; Hu, Hai-fei; Luo, Xiao; Zhang, Xue-jun

    2016-10-01

    Large flat mirrors play important roles in large aperture telescopes. However, they also introduce unpredictable problems. The surface errors created during manufacturing, testing, and supporting are all combined during measurement, thus making understanding difficult for diagnosis and treatment. Examining a high diameter-to-thickness ratio flat mirror, TMT M3MP, and its unexpected deformation during processing, we proposed a strain model of subsurface damage to explain the observed phenomenon. We designed a set of experiment, and checked the validity of our diagnosis. On that basis, we theoretical predicted the trend of this strain and its scale effect on Zerodur®, and checked the validity on another piece experimentally. This work guided the grinding-polishing process of M3MP, and will be used as reference for M3M processing as well.

  7. Influence of strain amount on stabilization of {omega}-phase in pure Ti by severe plastic deformation under high-pressure torsion

    Energy Technology Data Exchange (ETDEWEB)

    Todaka, Y; Azuma, H; Ohnishi, Y; Umemoto, M [Department of Production Systems Engineering, Toyohashi University of Technology, Hibarigaoka 1-1, Tempaku, Toyohashi, Aichi 441-8580 (Japan); Suzuki, H, E-mail: todaka@martens.pse.tut.ac.j [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Shirakata-Shirane 2-4, Tokai, Naka, Ibaraki 319-1195 (Japan)

    2010-07-01

    In pure Ti, the influence of shear deformation on the {alpha} to {omega} transformation and the development of texture in the {omega}-phase under high-pressure torsion (HPT) straining were investigated by means of X-ray and neutron diffractions. The fraction of {omega}-phase increased with strain in the {omega}-phase state. Bulk submicrocrystalline {omega}-Ti was fabricated by HPT-straining under the compressive pressure P = 5 GPa with the equivalent strain {epsilon}{sub eq} > 110 at the rotation speed of 3.3 x 10{sup -3} rev. per sec. (0.2 rev. per min.) at room temperature. The texture of {omega}-phase evolved by HPT-straining with the prismatic planes parallel to the shear direction of HPT-straining and the basal planes perpendicular to it.

  8. SU-F-19A-09: Propagation of Organ at Risk Contours for High Dose Rate Brachytherapy Planning for Cervical Cancer: A Deformable Image Registration Comparison

    Energy Technology Data Exchange (ETDEWEB)

    Bellon, M; Kumarasiri, A; Kim, J; Shah, M; Elshaikh, M; Chetty, I [Henry Ford Health System, Detroit, MI (United States)

    2014-06-15

    Purpose: To compare the performance of two deformable image registration (DIR) algorithms for contour propagation and to evaluate the accuracy of DIR for use with high dose rate (HDR) brachytherapy planning for cervical cancer. Methods: Five patients undergoing HDR ring and tandem brachytherapy were included in this retrospective study. All patients underwent CT simulation and replanning prior to each fraction (3–5 fractions total). CT-to-CT DIR was performed using two commercially available software platforms: SmartAdapt, Varian Medical Systems (Demons) and Velocity AI, Velocity Medical Solutions (B-spline). Fraction 1 contours were deformed and propagated to each subsequent image set and compared to contours manually drawn by an expert clinician. Dice similarity coefficients (DSC), defined as, DSC(A,B)=2(AandB)/(A+B) were calculated to quantify spatial overlap between manual (A) and deformed (B) contours. Additionally, clinician-assigned visual scores were used to describe and compare the performance of each DIR method and ultimately evaluate which was more clinically acceptable. Scoring was based on a 1–5 scale—with 1 meaning, “clinically acceptable with no contour changes” and 5 meaning, “clinically unacceptable”. Results: Statistically significant differences were not observed between the two DIR algorithms. The average DSC for the bladder, rectum and rectosigmoid were 0.82±0.08, 0.67±0.13 and 0.48±0.18, respectively. The poorest contour agreement was observed for the rectosigmoid due to limited soft tissue contrast and drastic anatomical changes, i.e., organ shape/filling. Two clinicians gave nearly equivalent average scores of 2.75±0.91 for SmartAdapt and 2.75±0.94 for Velocity AI—indicating that for a majority of the cases, more than one of the three contours evaluated required major modifications. Conclusion: Limitations of both DIR algorithms resulted in inaccuracies in contour propagation in the pelvic region, thus hampering the

  9. Microstructural Modification of Laser-Deposited High-Entropy CrFeCoNiMoWC Alloy by Friction Stir Processing: Nanograin Formation and Deformation Mechanism

    Science.gov (United States)

    Li, Ruidi; Wang, Minbo; Yuan, Tiechui; Song, Bo; Shi, Yusheng

    2017-02-01

    Nanostructured CrFeCoNiMoWC high-entropy alloy layer was developed through laser-melting deposition and severe plastic deformation (SPD). The laser-deposited CrFeCoNiMoWC alloy consists of dendritic and subeutectic with a continuous network structure. After SPD, the laser-deposited microstructure with grain size 3 to 4 μm was transformed into nanostructure with grain size 5 to 100 nm and the continuous networks were crushed into dispersed nanoparticles. The new phases of WC and Co3W were presented in the plastic zone after SPD due to the worn debris of the SPD tool. More interestingly, amorphous phase was found in the plastic zone, owing to the high temperature, high hydrostatic pressure, and large shear stress. The refined microstructure resulted in the enhancement of microhardness and electrochemical corrosion property. Many nanotwins were detected in the plastic zone; thus, strengthening mechanisms were reasonably inferred as twinning strengthening, work hardening, dispersion strengthening, refinement strengthening, and dislocation strengthening. The Lomer-Cottrell lock, full dislocation interacting with a partial dislocation at the twinning boundary, and high density of dislocation at the twinning boundary, stacking fault, and grain boundary were observed, which account for the property enhancement of the nanocrystalline.

  10. Preferred orientation in experimentally deformed stishovite: implications for deformation mechanisms

    Science.gov (United States)

    Kaercher, P. M.; Zepeda-Alarcon, E.; Prakapenka, V.; Kanitpanyacharoen, W.; Smith, J.; Sinogeikin, S. V.; Wenk, H. R.

    2014-12-01

    The crystal structure of the high pressure SiO2 polymorph stishovite has been studied in detail, yet little is known about its deformation mechanisms. Information about how stishovite deforms under stress is important for understanding subduction of quartz-bearing crustal rocks into the mantle. Particularly, stishovite is elastically anisotropic and thus development of crystallographic preferred orientation (CPO) during deformation may contribute to seismic anomalies in the mantle. We converted a natural sample of flint to stishovite in a laser heated diamond anvil cell and compressed the stishovite aggregate up to 38 GPa. Diffraction patterns were collected in situ in radial geometry at the Advanced Light Source (ALS) and the Advanced Photon Source (APS) to examine development of CPO during deformation. We find that (001) poles preferentially align with the compression direction and infer deformation mechanisms leading to the observed CPO with visco-plastic self consistent (VPSC) polycrystal plasticity models. Our results show pyramidal and basal slip are most likely active at high pressure and ambient temperature, in agreement with transmission electron microscopy (TEM) studies of rutile (TiO2) and paratellurite (TeO2), which are isostructural to stishovite. Conversely other TEM studies of stishovite done at higher temperature suggest dominant prismatic slip. This indicates that a variety of slip systems may be active in stishovite, depending on conditions. As a result, stishovite's contribution to the seismic signature in the mantle may vary as a function of pressure and temperature and thus depth.

  11. Deformations of crystal frameworks

    CERN Document Server

    Borcea, Ciprian S

    2011-01-01

    We apply our deformation theory of periodic bar-and-joint frameworks to tetrahedral crystal structures. The deformation space is investigated in detail for frameworks modelled on quartz, cristobalite and tridymite.

  12. Deformed General Relativity

    CERN Document Server

    Bojowald, Martin

    2013-01-01

    Deformed special relativity is embedded in deformed general relativity using the methods of canonical relativity and loop quantum gravity. Phase-space dependent deformations of symmetry algebras then appear, which in some regimes can be rewritten as non-linear Poincare algebras with momentum-dependent deformations of commutators between boosts and time translations. In contrast to deformed special relativity, the deformations are derived for generators with an unambiguous physical role, following from the relationship between canonical constraints of gravity with stress-energy components. The original deformation does not appear in momentum space and does not give rise to non-locality issues or problems with macroscopic objects. Contact with deformed special relativity may help to test loop quantum gravity or restrict its quantization ambiguities.

  13. Thermomechanical Modeling of Laser-Induced Structural Relaxation and Deformation of Glass: Volume Changes in Fused Silica at High Temperatures [Thermo-mechanical modeling of laser-induced structural relaxation and deformation of SiO2 glass

    Energy Technology Data Exchange (ETDEWEB)

    Vignes, Ryan M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). National Ignition Facility and Photon Sciences; Soules, Thomas F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). National Ignition Facility and Photon Sciences; Stolken, James S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). National Ignition Facility and Photon Sciences; Settgast, Randolph R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). National Ignition Facility and Photon Sciences; Elhadj, Selim [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). National Ignition Facility and Photon Sciences; Matthews, Manyalibo J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). National Ignition Facility and Photon Sciences; Mauro, J.

    2012-12-17

    In a fully coupled thermomechanical model of the nanoscale deformation in amorphous SiO2 due to laser heating is presented. Direct measurement of the transient, nonuniform temperature profiles was used to first validate a nonlinear thermal transport model. Densification due to structural relaxation above the glass transition point was modeled using the Tool-Narayanaswamy (TN) formulation for the evolution of structural relaxation times and fictive temperature. TN relaxation parameters were derived from spatially resolved confocal Raman scattering measurements of Si–O–Si stretching mode frequencies. These thermal and microstructural data were used to simulate fictive temperatures which are shown to scale nearly linearly with density, consistent with previous measurements from Shelby et al. Volumetric relaxation coupled with thermal expansion occurring in the liquid-like and solid-like glassy states lead to residual stresses and permanent deformation which could be quantified. But, experimental surface deformation profiles between 1700 and 2000 K could only be reconciled with our simulation by assuming a roughly 2 × larger liquid thermal expansion for a-SiO2 with a temperature of maximum density ~150 K higher than previously estimated by Bruckner et al. Calculated stress fields agreed well with recent laser-induced critical fracture measurements, demonstrating accurate material response prediction under processing conditions of practical interest.

  14. Deformation Twinning During Nanoindentation of Nanocrystalline Ta

    OpenAIRE

    Wang, Y. M.; Hodge, A. M.; Biener, J.; Hamza, A.V.; Barnes, D E; Liu, Kai; Nieh, T. G.

    2005-01-01

    The deformation mechanism of body-centered cubic (bcc) nanocrystalline tantalum with grain sizes of 10–30 nm is investigated by nanoindentation, scanning electron microscopy and high-resolution transmission electron microscopy. In a deviation from molecular dynamics simulations and existing experimental observations on other bcc nanocrystalline metals, the plastic deformation of nanocrystalline Ta during nanoindentation is controlled by deformation twinning. The observation of multiple twin i...

  15. The Effect of Increasing Sn Content on High-Temperature Mechanical Deformation of an Mg-3%Cu-1%Ca Alloy

    Directory of Open Access Journals (Sweden)

    Georgios S.E. Antipas

    2013-11-01

    Full Text Available Chill casting of magnesium alloy samples with secondary alloying elements of Cu, Ca and Sn at % w.t. concentrations in the range 1–5, 0.1–5 and 0.1–3 respectively, gave rise to appreciably enhanced resistance to high-temperature creep, while maintaining good heat conductivity. The latter was considered to be driven by Cu and Mg-Cu intermetallics while it was clear that Sn mediated the high-temperature performance, mainly via networks of Mg2Sn and MgCaSn precipitates along the Mg matrix grain boundaries. It was postulated that Sn formed intermetallics by preferential substitution of Ca atoms and, thus, did not degrade the heat conductivity by retaining Cu. The % w.t. stoichiometry with the optimum combination of heat conductivity and resistance to high-temperature creep was found to be Mg-3Cu-1Ca-0.1Sn.

  16. Recurrent landsliding of a high bank at Dunaszekcső, Hungary: Geodetic deformation monitoring and finite element modeling

    Science.gov (United States)

    Bányai, László; Mentes, Gyula; Újvári, Gábor; Kovács, Miklós; Czap, Zoltán; Gribovszki, Katalin; Papp, Gábor

    2014-04-01

    Five years of geodetic monitoring data at Dunaszekcső, Hungary, are processed to evaluate recurrent landsliding, which is a characteristic geomorphological process affecting the high banks of the Middle Danube valley in Hungary. The integrated geodetic observations provide accurate three dimensional coordinate time series, and these data are used to calculate the kinematic features of point movements and the rigid body behavior of point blocks. Additional datasets include borehole tiltmeter data and hydrological recordings of the Danube and soil water wells. These data, together with two dimensional final element analyses, are utilized to gain a better understanding of the physical, soil mechanical background and stability features of the high bank. Here we indicate that the main trigger of movements is changing groundwater levels, whose effect is an order of magnitude higher than that of river water level changes. Varying displacement rates of the sliding blocks are interpreted as having been caused by basal pore water pressure changes originating from shear zone volume changes, floods of the River Danube through later seepage and rain infiltration. Both data and modeling point to the complex nature of bank sliding at Dunaszekcső. Some features imply that the movements are rotational, some reveal slumping. By contrast, all available observational and modeling data point to the retrogressive development of the high bank at Dunaszekcső. Regarding mitigation, the detailed analysis of three basic parameters (the direction of displacement vectors, tilting, and the acceleration component of the kinematic function) is suggested because these parameters indicate the zone where the largest lateral displacements can be expected and point to the advent of the rapid landsliding phase that affects high banks along the River Danube.

  17. Foot deformities, function in the lower extremities, and plantar pressure in patients with diabetes at high risk to develop foot ulcers

    Directory of Open Access Journals (Sweden)

    Ulla Hellstrand Tang

    2015-06-01

    Full Text Available Objective: Foot deformities, neuropathy, and dysfunction in the lower extremities are known risk factors that increase plantar peak pressure (PP and, as a result, the risk of developing foot ulcers in patients with diabetes. However, knowledge about the prevalence of these factors is still limited. The aim of the present study was to describe the prevalence of risk factors observed in patients with diabetes without foot ulcers and to explore possible connections between the risk factors and high plantar pressure. Patients and methods: Patients diagnosed with type 1 (n=27 or type 2 (n=47 diabetes (mean age 60.0±15.0 years were included in this cross-sectional study. Assessments included the registration of foot deformities; test of gross function at the hip, knee, and ankle joints; a stratification of the risk of developing foot ulcers according to the Swedish National Diabetes Register; a walking test; and self-reported questionnaires including the SF-36 health survey. In-shoe PP was measured in seven regions of interests on the sole of the foot using F-Scan®. An exploratory analysis of the association of risk factors with PP was performed. Results: Neuropathy was present in 28 (38%, and 39 (53% had callosities in the heel region. Low forefoot arch was present in 57 (77%. Gait-related parameters, such as the ability to walk on the forefoot or heel, were normal in all patients. Eighty percent had normal function at the hip and ankle joints. Gait velocity was 1.2±0.2 m/s. All patients were stratified to risk group 3. Hallux valgus and hallux rigidus were associated with an increase in the PP in the medial forefoot. A higher body mass index (BMI was found to increase the PP at metatarsal heads 4 and 5. Pes planus was associated with a decrease in PP at metatarsal head 1. Neuropathy did not have a high association with PP. Conclusions: This study identified several potential risk factors for the onset of diabetic foot ulcers (DFU. Hallux valgus

  18. An experimental investigation of thermally-induced deformation of 1 micron thick copper/tantalum/polymide high-density interconnect structures

    Science.gov (United States)

    Zhmurkin, Dmitry V.

    A new technique to estimate the out-of-plane thermal expansion coefficient (CTE) of several 1 mum thick, spin-coated polyimides is introduced. Arrays of parallel copper and polyimide lines of various aspect ratios on Si substrate were imaged in air at room temperature and at 97sp°C using an atomic force microscope (AFM). The out-of-plane CTE of the polyimides was estimated by matching the experimental results with the predictions of finite element models with different out-of-plane parameters. For FPI-135 (6FCDA-TMOB) polyimide the out-of-plane CTE was found to be ≈260 ppm/sp°C, for FPI-136 (PMDA-6FDA-TFMOB) polyimide ≈120 ppm/sp°C. Polyimide lines with widths equal to or less than the film thickness of 1 mum showed less thermal expansion than wider lines. This was attributed to change of polyimide properties at the Cu/polyimide interface as a result of the reactive ion etching step of the structure manufacturing process. High density interconnect structures are subjected to 350sp°C during manufacturing. The mismatch between the Cu and the polyimide out-of-plane CTE leads to high shear stresses at the interfaces normal to the film plane during heating. The experimental observation of thermally induced deformation of Cu/Ta/polyimide line arrays as a result of RT-350sp°C-RT thermal cycle is discussed. In addition to "classical" high temperature deformation mechanisms (grain boundary sliding, grain elevation and Coble creep on the Cu surface), sliding at the Cu/Ta interface was observed using the AFM. It was found that the Cu/Ta interfacial sliding is a strong function of the Cu line width. 10 mum wide Cu lines were found to exhibit less Cu/Ta sliding compared to 1 mum wide Cu lines. This was attributed to ability of wide Cu lines relax the stresses using other mechanisms. A finite element model was constructed to analyze the Cu/Ta interfacial sliding.

  19. A coupled model between mechanical deformation and chemical diffusion: An explanation for the preservation of chemical zonation in plagioclase at high temperatures

    Science.gov (United States)

    Zhong, Xin; Vrijmoed, Johannes; Moulas, Evangelos; Tajcmanová, Lucie

    2016-04-01

    Compositional zoning in metamorphic minerals have been generally recognized as an important geological feature to decipher the metamorphic history of rocks. The observed chemical zoning of, e.g. garnet, is commonly interpreted as disequilibrium between the fractionated inner core and the surrounding matrix. However, chemically zoned minerals were also observed in high grade rocks (T>800 degree C) where the duration of metamorphic processes was independently dated to take several Ma. This implies that temperature may not be the only factor that controls diffusion timescales, and grain scale pressure variation was proposed to be a complementary factor that may significantly contribute to the formation and preservation of chemical zoning in high temperature metamorphic minerals [Tajcmanová 2013, 2015]. Here, a coupled model is developed to simulate viscous deformation and chemical diffusion. The numerical approach considers the conservation of mass, momentum, and a constitutive relation developed from equilibrium thermodynamics. A compressible viscoelastic rheology is applied, which associates the volumetric change triggered by deformation and diffusion to a change of pressure. The numerical model is applied to the chemically zoned plagioclase rim described by [Tajcmanová 2014]. The diffusion process operating during the plagioclase rim formation can lead to a development of a pressure gradient. Such a pressure gradient, if maintained during ongoing viscous relaxation, can lead to the preservation of the observed chemical zonation in minerals. An important dimensionless number, the Deborah number, is defined as the ratio between the Maxwell viscoelastic relaxation time and the characteristic diffusion time. It characterizes the relative influence between the maintenance of grain scale pressure variation and chemical diffusion. Two extreme regimes are shown: the mechanically-controlled regime (high Deborah number) and diffusion-controlled regime (low Deborah number

  20. High-resolution remote sensing image-based extensive deformation-induced landslide displacement field monitoring method

    Institute of Scientific and Technical Information of China (English)

    Shanjun Liu; Han Wang; Jianwei Huang; Lixin Wu

    2015-01-01

    Landslide is one of the multitudinous serious geological hazards. The key to its control and reduction lies on dynamic monitoring and early warning. The article points out the insufficiency of traditional measuring means applied for large-scale landslide monitoring and proposes the method for extensive landslide displacement field monitoring using high-resolution remote images. Matching of cognominal points is realized by using the invariant features of SIFT algorithm in image translation, rotation, zooming, and affine transformation, and through recognition and comparison of characteristics of high-resolution images in different landsliding periods. Following that, landslide displacement vector field can be made known by measuring the distances and directions between cognominal points. As evidenced by field application of the method for landslide monitoring at West Open Mine in Fushun city of China, the method has the attraction of being able to make areal measurement through satellite observation and capable of obtaining at the same time the information of large-area intensive displacement field, for facilitating automatic delimitation of extent of landslide displacement vector field and sliding mass. This can serve as a basis for making analysis of laws governing occurrence of landslide and adoption of countermeasures.

  1. Deformable Nanolaminate Optics

    Energy Technology Data Exchange (ETDEWEB)

    Olivier, S S; Papavasiliou, A P; Barbee, T W; Miles, R R; Walton, C C; Cohn, M B; Chang, K

    2006-05-12

    We are developing a new class of deformable optic based on electrostatic actuation of nanolaminate foils. These foils are engineered at the atomic level to provide optimal opto-mechanical properties, including surface quality, strength and stiffness, for a wide range of deformable optics. We are combining these foils, developed at Lawrence Livermore National Laboratory (LLNL), with commercial metal processing techniques to produce prototype deformable optics with aperture sizes up to 10 cm and actuator spacing from 1 mm to 1 cm and with a range of surface deformation designed to be as much as 10 microns. The existing capability for producing nanolaminate foils at LLNL, coupled with the commercial metal processing techniques being used, enable the potential production of these deformable optics with aperture sizes of over 1 m, and much larger deformable optics could potentially be produced by tiling multiple deformable segments. In addition, based on the fabrication processes being used, deformable nanolaminate optics could potentially be produced with areal densities of less than 1 kg per square m for applications in which lightweight deformable optics are desirable, and deformable nanolaminate optics could potentially be fabricated with intrinsically curved surfaces, including aspheric shapes. We will describe the basic principles of these devices, and we will present details of the design, fabrication and characterization of the prototype deformable nanolaminate optics that have been developed to date. We will also discuss the possibilities for future work on scaling these devices to larger sizes and developing both devices with lower areal densities and devices with curved surfaces.

  2. Cryogenic strength improvement by utilizing room-temperature deformation twinning in a partially recrystallized VCrMnFeCoNi high-entropy alloy.

    Science.gov (United States)

    Jo, Y H; Jung, S; Choi, W M; Sohn, S S; Kim, H S; Lee, B J; Kim, N J; Lee, S

    2017-06-12

    The excellent cryogenic tensile properties of the CrMnFeCoNi alloy are generally caused by deformation twinning, which is difficult to achieve at room temperature because of insufficient stress for twinning. Here, we induced twinning at room temperature to improve the cryogenic tensile properties of the CrMnFeCoNi alloy. Considering grain size effects on the critical stress for twinning, twins were readily formed in the coarse microstructure by cold rolling without grain refinement by hot rolling. These twins were retained by partial recrystallization and played an important role in improving strength, allowing yield strengths approaching 1 GPa. The persistent elongation up to 46% as well as the tensile strength of 1.3 GPa are attributed to additional twinning in both recrystallized and non-recrystallization regions. Our results demonstrate that non-recrystallized grains, which are generally avoided in conventional alloys because of their deleterious effect on ductility, can be useful in achieving high-strength high-entropy alloys.

  3. The Effect Of Strain Rate On The Mechanical Properties And Microstructure Of The High-Mn Steel After Dynamic Deformation Tests

    Directory of Open Access Journals (Sweden)

    Jabłońska M.B.

    2015-06-01

    Full Text Available The paper presents results of dynamic tensile investigations of high-manganese Fe – 20 wt.% Mn – 3 wt.% Al – 3 wt.% Si – 0.2 wt.% steel. The research was carried out on a flywheel machine, which enables to perform dynamic tensile tests and impact bending with a linear velocity of the enforcing element in the range of 5÷40 m/s. It was found that the studied steel was characterized by very good mechanical properties. Strength of the tested materials was determined in the static tensile test and dynamic deformation test, while its hardness was measured with the Vickers hardness test method. The surface of fractures that were created in the areas where the sample was torn were analyzed. These fractures indicate the presence of transcrystalline ductile fractures. Fractographic tests were performed with the use of a scanning electron microscope. The structure was analyzed by light optical microscopy. Substructure studies revealed occurrence of mechanical twinning induced by high strain rates. A detailed analysis of the structure was performed with the use of a transmission scanning electron microscope STEM.

  4. Anatomically accurate high resolution modeling of human whole heart electromechanics: A strongly scalable algebraic multigrid solver method for nonlinear deformation

    Science.gov (United States)

    Augustin, Christoph M.; Neic, Aurel; Liebmann, Manfred; Prassl, Anton J.; Niederer, Steven A.; Haase, Gundolf; Plank, Gernot

    2016-01-01

    Electromechanical (EM) models of the heart have been used successfully to study fundamental mechanisms underlying a heart beat in health and disease. However, in all modeling studies reported so far numerous simplifications were made in terms of representing biophysical details of cellular function and its heterogeneity, gross anatomy and tissue microstructure, as well as the bidirectional coupling between electrophysiology (EP) and tissue distension. One limiting factor is the employed spatial discretization methods which are not sufficiently flexible to accommodate complex geometries or resolve heterogeneities, but, even more importantly, the limited efficiency of the prevailing solver techniques which is not sufficiently scalable to deal with the incurring increase in degrees of freedom (DOF) when modeling cardiac electromechanics at high spatio-temporal resolution. This study reports on the development of a novel methodology for solving the nonlinear equation of finite elasticity using human whole organ models of cardiac electromechanics, discretized at a high para-cellular resolution. Three patient-specific, anatomically accurate, whole heart EM models were reconstructed from magnetic resonance (MR) scans at resolutions of 220 μm, 440 μm and 880 μm, yielding meshes of approximately 184.6, 24.4 and 3.7 million tetrahedral elements and 95.9, 13.2 and 2.1 million displacement DOF, respectively. The same mesh was used for discretizing the governing equations of both electrophysiology (EP) and nonlinear elasticity. A novel algebraic multigrid (AMG) preconditioner for an iterative Krylov solver was developed to deal with the resulting computational load. The AMG preconditioner was designed under the primary objective of achieving favorable strong scaling characteristics for both setup and solution runtimes, as this is key for exploiting current high performance computing hardware. Benchmark results using the 220 μm, 440 μm and 880 μm meshes demonstrate

  5. High temperature uniaxial deformation experiment of bubble-free highly crystalline magmas; a case study for the high-Mg andesite from Goshiki-dai lava plateau, southwest Japan (Invited)

    Science.gov (United States)

    Ishibashi, H.

    2013-12-01

    Rheological property of magma is a key factor for understanding various volcanic processes. Natural magmas commonly have crystals of various volume fraction and such suspended crystals strongly affect on magma rheology. For dilute to intermediately crystalline magmas, previous studies (e.g., Ishibashi, 2009JVGR; Vona et al. 2011ChemGeol) experimentally investigated the effects of suspended crystals on apparent viscosities and the model predicting the effects of crystals is proposed by Mader et al. (2013JVGR). However, for highly crystalline magmas, our knowledge on their complex rheological behaviors is still not enough even for bubble-free system whereas several experimental studies have been done (e.g., Carrichi et al., 2007EPSL; Picard et al., 2013JGR). Understanding rheological property in the crystal-melt two phase system is important for considering magma dynamics in deep magma chambers and dykes and also for investigating the property in bubble-crystal-melt three phase system. In this study, uniaxial compression deformation experiments were done for bubble-free, highly crystalline natural lava under high temperature, 1atm pressure conditions to investigate the effects of suspended crystals on rheology of bubble-free magma. The high-Mg andesite erupted at ca. 15 Ma from Goshiki-dai lava plateau, southwest Japan, was used for starting materials. The lava is aphyric, bubble-free, and composed of fine-grained elongated plagioclase, pyroxenes, and magnetite crystals and unaltered silicate glass. Crystal volume fraction is ca. 0.65. Samples were cut into rectangular with 15mm length, 15mm width, and 30 mm high from massive portion of lava without any visible fracture. The samples were deformed by using the high temperature uniaxial compression apparatus, installed at Earthquake Research Institute, the University of Tokyo, under conditions of temperature from 1292 to 1133 K, log strain rate from -5.5 to -2.5, and 1 atm pressure. Total strains of the samples are

  6. Mechanisms of deformation and fracture in high temperature low cycle fatigue of Rene 80 and IN 100

    Science.gov (United States)

    Romanoski, G. R., Jr.

    1982-01-01

    Specimens tested for the AGARD strain range partitioning program were investigated. Rene 80 and IN 100 were tested in air and in vacuum; at 871 C, 925 C, and 1000 C; and in the coated and uncoated condition. The specimens exhibited a multiplicity of high-temperature low-cycle fatigue damage. Observations of the various forms of damage were consistent with material and testing conditions and were generally in agreement with previous studies. In every case observations support a contention that failure occurs at a particular combination of crack length and maximum stress. A failure criterion which is applicable in the regime of testing studied is presented. The predictive capabilities of this criterion are straight forward.

  7. Influence of Partitioning Process on the Microstructure and Mechanical Properties of High Deformability Oil-Gas Pipeline

    Directory of Open Access Journals (Sweden)

    Jing Ma

    2014-11-01

    Full Text Available Multiphase structure of bainite and M/A constituent can be obtained for X80 oil-gas pipeline through a novel heat online partitioning (HOP technology. The effects of partitioning temperature on the microstructure and mechanical properties of the experimental steels were researched by means of mechanical properties test, microscopic analysis, and X-ray diffraction. The results show that with the increase of the partitioning temperature, the strength of the experimental steel decreases and the ductility increases because of the increase of bainite lath width, the decrease of dislocation density, the increase of retained austenite content, and carbides coarsening. The decrease of the volume content and stability of retained austenite is the key factor, which leads to the increase of strength and the decrease of plasticity in a high range of partitioning temperature.

  8. The effect of high density electric pulses on sintered aluminum 201AB silicon carbide MMC PM compacts during plastic deformation

    Science.gov (United States)

    Dariavach, Nader Guseinovich

    The effect of high-density electrical pulses on mechanical and structural properties of sintered aluminum SiC metal-matrix composites, fabricated by standard powder-metallurgy compaction and sintering, was investigated. Three types of phenomena where investigated during transverse rupture testing of the samples: a consolidation effect (increasing of the transverse rupture strength (TRS)), an electroplastic effect (decreasing of the flow stresses), and an increasing of the stress intensity factor by electric pulse application. It was observed, that an increase in the TRS strength of sintered powder metallurgy (PM) aluminum and aluminum metal matrix composite (MMC) compacts is a result of the electric pulse consolidation effect due to non-uniform temperature distribution around the grain boundaries. Three analytical models of the thermal effect of electric pulses on aluminum samples where considered: total temperature change of the sample due to a one electric pulse, one-dimensional steady state model and transient 2D thermal analysis of the temperature distribution around the grain boundary. The 2D transient analysis shows that the temperature rise in the grain boundary of a sintered PM aluminum sample due to an electric pulse can exceed the melting point. At the same time the temperature of the bulk material has an insignificant (melt the crack tip and increase the strength of the damaged material. The experimental study shows an increase in the stress intensity factor up to 76% for sintered aluminum PM compacts and up to 116% for sintered aluminum MMC PM compacts due to application of high-density electric pulses during transverse rapture testing.

  9. Deformation mechanism of black batt with high stress in Baozhen tunnel%堡镇隧道高地应力炭质页岩的变形破坏机制

    Institute of Scientific and Technical Information of China (English)

    田四明

    2013-01-01

    Large amount of deformation, high deformation rate, long deformation duration and obvious dissymmetry and non-uniformity in space-time effect are primary characteristics of rock mass around Baozhen Tunnel for Yiwan Railway. Aiming at the problems occurring in construction of the tunnel, including large deformation of carbonaceous shale, distortion and fracture of surrounding rock and support structure, based on statistical analysis of field monitoring data and geological sketch of tunnel heading, deformation and failure mechanism of carbonaceous shale have been analyzed by engineering geology and structural mechanics, affection of rock stratification and soft interlayer on stability of surrounding rock has been discussed, deformation and failure mechanism of carbonaceous shale under high ground stress has been uncovered in the paper. The research results indicate that deformation and failure forms of carbonaceous shale around Baozhen Tunnel principally involve extrusion deformation along bedding, bending deformation of rock beam, rib fall, inbreak, bottom squeeze of muddy interlayer, deformation of sidewall provoked by weak interlayer. Deformation and failure characteristics principally include symbiosis, non-uniformity, zonation, dissymmetry, concentricity and domination of weak interlayer on large deformation. The deformation mechanism presents diversity, coexistence and reciprocal transformation.%宜万铁路堡镇隧道围岩变形量大、变形速率快、持续时间长,且在时空效应上具有明显的不对称性和不均匀性.针对隧道施工中出现的炭质页岩大变形、围岩和支护结构扭曲折断和破坏等问题,基于现场监测数据的统计分析和掌子面素描,运用工程地质学和结构力学相关理论,分析高地应力炭质页岩的变形破坏机制,探讨了层状岩层和软弱夹层对隧道围岩稳定性的影响,揭示了高地应力炭质页岩变形破坏的力学机制.研究结果表明:堡镇隧道炭

  10. Shear deformation and division of cylindrical walls in free-standing nematic films under high electric fields.

    Science.gov (United States)

    Tadapatri, Pramod; Krishnamurthy, K S

    2008-10-30

    We report on the behavior of cylindrical walls formed in a substrate-free nematic film of PCH5 under the action of an in-plane ac field. In the film, with vertical molecular alignment at all the limiting surfaces, annular Brochard-Leger walls are induced well above the bend-Freedericksz threshold. They exhibit, at high field strengths, a new type of instability not encountered in sandwich, or any other, cell configuration. It manifests as a shearing of the loop-wall between the opposite free-surfaces. The shear strain is measured as a function of time, field strength, frequency, and temperature. Significantly, the strain is linear in field strength. The origin of shear and its dependence on field variables are explained through an adaptation of the Carr-Helfrich mechanism of charge separation. The sheared wall is stable against pincement up to several times the threshold field, and divides itself into two fragments under a large enough strain. With the shear distortion, linear defects appear in the opposite splay-bend regions, just as Neel lines in Bloch walls of magnetic systems. At very low frequencies, flexoelectric influence on distortion is revealed.

  11. Deformation Behavior of Al0.25CoCrFeNi High-Entropy Alloy after Recrystallization

    Directory of Open Access Journals (Sweden)

    Jinxiong Hou

    2017-03-01

    Full Text Available Cold rolling with subsequent annealing can be used to produce the recrystallized structure in high entropy alloys (HEAs. The Al0.25CoCrFeNi HEAs rolled to different final thickness (230, 400, 540, 800, 1000, 1500 μm are prepared to investigate their microstructure evolutions and mechanical behaviors after annealing. Only the single face-centered cubic phase was obtained after cold rolling and recrystallization annealing at 1100 °C for 10 h. The average recrystallized grain size in this alloy after annealing ranges from 92 μm to 136 μm. The annealed thin sheets show obviously size effects on the flow stress and formability. The yield strength and tensile strength decrease as t/d (thickness/average grain diameter ratio decreases until the t/d approaches 2.23. In addition, the stretchability (formability decreases with the decrease of the t/d ratio especially when the t/d ratio is lower than about 6. According to the present results, yield strength can be expressed as a function of the t/d ratio.

  12. A non-randomized controlled clinical trial on autologous chondrocyte implantation (ACI) in cartilage defects of the medial femoral condyle with or without high tibial osteotomy in patients with varus deformity of less than 5°

    DEFF Research Database (Denmark)

    Bode, Gerrit; Schmal, Hagen; Pestka, Jan M

    2013-01-01

    PURPOSE: High tibial osteotomy (HTO) is a recommended concomitant surgery when treating cartilage lesions of the medial femoral condyle (MFC). Varus deformities of 5° and more were considered an indication for HTO in patients with cartilage defects. This study compares clinical outcome in patients...

  13. MICROSTRUCTURE EVOLUTION AND DEFORMATION BEHAVIOR OF HIGH MANGANESE TRIP/TWIP SYMBIOTIC EFFECT STEELS UNDER HIGH-SPEED DEFORMATION%高锰TRIP/TWIP效应共生钢高速变形过程中的组织演变及变形行为

    Institute of Scientific and Technical Information of China (English)

    唐正友; 吴志强; 昝娜; 丁桦

    2011-01-01

    对18Mn-3Al-3Si和21Mn-3Al-3Si高锰TRIP/TWIP效应共生钢动态变形过程中的变形行为,应变硬化速率、真应力和应变硬化指数随真应变的变化,以及应变硬化和基体软化间的相互作用等进行了研究,采用OM,SEM,TEM和XRD等方法对变形前后的组织进行了分析.结果表明,高应变速率下,TRIP/TWIP效应共生钢应变诱发相变途径为γ→ε→α;高速变形对滑移的抑制、奥氏体向马氏体的相变和形变孪晶对奥氏体晶粒的细化是应变硬化的主要因素;造成基体软化的原因是绝热温升效应、ε→γ的逆相变和孪晶的动态再结晶.%The high manganese TRIP/TWIP symbiotic effect steel exhibits excellent combination of strength and elongation due to the transformation-induced plasticity and twinning-induced plasticity. In this paper, by means of a Zwick HTM 5020 high rate tensile test machine, the mechanical behavior of 18Mn-3Al-3Si and 21Mn-3Al-3Si high manganese TRIP/TWIP symbiotic effect steels under dynamic condition, strain hardening rate, true stress and strain hardening exponent show fluctuating with the true stain change, which is caused by the interaction between strain hardening and matrix softening. The microstructure evolution of the specimen was analyzed by OM, SEM, TEM and XRD. The results indicate that the transformation route is γ→ε, ε→α under high-speed deformation; hindering of high-speed deformation to slip, transformation from austenite to martensite, and refinement of austenite matrix due to deformation twins are the main factors of strain hardening; while adiabatic temperature rise effect, ε→γ reverse transformation and dynamic recrystallization of twins make the matrix softening.

  14. High-fidelity tissue engineering of patient-specific auricles for reconstruction of pediatric microtia and other auricular deformities.

    Directory of Open Access Journals (Sweden)

    Alyssa J Reiffel

    Full Text Available INTRODUCTION: Autologous techniques for the reconstruction of pediatric microtia often result in suboptimal aesthetic outcomes and morbidity at the costal cartilage donor site. We therefore sought to combine digital photogrammetry with CAD/CAM techniques to develop collagen type I hydrogel scaffolds and their respective molds that would precisely mimic the normal anatomy of the patient-specific external ear as well as recapitulate the complex biomechanical properties of native auricular elastic cartilage while avoiding the morbidity of traditional autologous reconstructions. METHODS: Three-dimensional structures of normal pediatric ears were digitized and converted to virtual solids for mold design. Image-based synthetic reconstructions of these ears were fabricated from collagen type I hydrogels. Half were seeded with bovine auricular chondrocytes. Cellular and acellular constructs were implanted subcutaneously in the dorsa of nude rats and harvested after 1 and 3 months. RESULTS: Gross inspection revealed that acellular implants had significantly decreased in size by 1 month. Cellular constructs retained their contour/projection from the animals' dorsa, even after 3 months. Post-harvest weight of cellular constructs was significantly greater than that of acellular constructs after 1 and 3 months. Safranin O-staining revealed that cellular constructs demonstrated evidence of a self-assembled perichondrial layer and copious neocartilage deposition. Verhoeff staining of 1 month cellular constructs revealed de novo elastic cartilage deposition, which was even more extensive and robust after 3 months. The equilibrium modulus and hydraulic permeability of cellular constructs were not significantly different from native bovine auricular cartilage after 3 months. CONCLUSIONS: We have developed high-fidelity, biocompatible, patient-specific tissue-engineered constructs for auricular reconstruction which largely mimic the native auricle both

  15. Relationships among physical properties as indicators of high temperature deformation or post-shock thermal annealing in ordinary chondrites

    Science.gov (United States)

    Friedrich, Jon M.; Ruzicka, Alex; Macke, Robert J.; Thostenson, James O.; Rudolph, Rebecca A.; Rivers, Mark L.; Ebel, Denton S.

    2017-04-01

    Collisions and attendant shock compaction must have been important for the accretion and lithification of planetesimals, including the parent bodies of chondrites, but the conditions under which these occurred are not well constrained. A simple model for the compaction of chondrites predicts that shock intensity as recorded by shock stage should be related to porosity and grain fabric. To test this model, we studied sixteen ordinary chondrites of different groups (H, L, LL) using X-ray computed microtomography (μCT) to measure porosity and metal fabric, ideal gas pycnometry and 3D laser scanning to determine porosity, and optical microscopy (OM) to determine shock stage. These included a subsample of six chondrites previously studied using transmission electron microscopy (TEM) to characterize microstructures in olivine. Combining with previous data, results support the simple model in general, but not for chondrites with low shock-porosity-foliation (low-SPF chondrites). These include Kernouvé (H6), Portales Valley (H6/7), Butsura (H6), Park (L6), GRO 85209 (L6), Estacado (H6), MIL 99301 (LL6), Spade (H6), and Queen's Mercy (H6), among others. The data for these meteorites are best explained by high ambient heat during or after shock. Low-SPF chondrites tend to have older 40Ar/39Ar ages (∼4435-4526 Ma) than other, non-low-SPF type 6 chondrites in this study. We conclude that the H, L, and LL asteroids all were shock-compacted at an early stage while warm, with collisions occurring during metamorphic heating of the parent bodies. Results ultimately bear on whether chondrite parent bodies have internal structures more akin to a metamorphosed onion shell or metamorphosed rubble pile, and on the nature of accretion and lithification processes for planetesimals.

  16. Relationships among physical properties as indicators of high temperature deformation or post-shock thermal annealing in ordinary chondrites

    Energy Technology Data Exchange (ETDEWEB)

    Friedrich, Jon M.; Ruzicka, Alex; Macke, Robert J.; Thostenson, James O.; Rudolph, Rebecca A.; Rivers, Mark L.; Ebel, Denton S.

    2017-04-01

    Collisions and attendant shock compaction must have been important for the accretion and lithification of planetesimals, including the parent bodies of chondrites, but the conditions under which these occurred are not well constrained. A simple model for the compaction of chondrites predicts that shock intensity as recorded by shock stage should be related to porosity and grain fabric. To test this model, we studied sixteen ordinary chondrites of different groups (H, L, LL) using X-ray computed microtomography (μCT) to measure porosity and metal fabric, ideal gas pycnometry and 3D laser scanning to determine porosity, and optical microscopy (OM) to determine shock stage. These included a subsample of six chondrites previously studied using transmission electron microscopy (TEM) to characterize microstructures in olivine. Combining with previous data, results support the simple model in general, but not for chondrites with low shock-porosity-foliation (low-SPF chondrites). These include Kernouvé (H6), Portales Valley (H6/7), Butsura (H6), Park (L6), GRO 85209 (L6), Estacado (H6), MIL 99301 (LL6), Spade (H6), and Queen’s Mercy (H6), among others. The data for these meteorites are best explained by high ambient heat during or after shock. Low-SPF chondrites tend to have older 40Ar/39Ar ages (~4435–4526 Ma) than other, non-low-SPF type 6 chondrites in this study. We conclude that the H, L, and LL asteroids all were shock-compacted at an early stage while warm, with collisions occurring during metamorphic heating of the parent bodies. Results ultimately bear on whether chondrite parent bodies have internal structures more akin to a metamorphosed onion shell or metamorphosed rubble pile, and on the nature of accretion and lithification processes for planetesimals.

  17. Two-dimensional (2-D) deformation measurements with ASAR and PHARUS

    NARCIS (Netherlands)

    Groot, J.S.; Halsema, D. van; Maarseveen, R.A. van; Blommaart, P.J.L.; Kruse, G.A.M.; Loon, D. van; Hanssen, R.F.; Samson, J.; Striegel, A.J.; Visser, J.M.P.C.M.

    2001-01-01

    Deformation measurements are important in the field of ground engineering. Deformation can have a non-natural cause (e.g., surface deformation due to tunnel construction) or a natural one (e.g., dike deformation due to a high water level). Radar interferometry can in principle provide deformations w

  18. 强光辐照下白宝石高反镜尺寸对热变形的影响%Effect of dimensions on thermal deformation of high reflectance sapphire mirrors under high power laser irradiation

    Institute of Scientific and Technical Information of China (English)

    梅艳莹; 杨涛

    2014-01-01

    为了进一步减小白宝石( Al2 O3)高反镜在强光辐照下的热变形,提高光束质量,研究了白宝石高反镜厚度、直径尺寸对热变形的影响。采用以极坐标表示的热传导方程和热变形公式来描述白宝石高反镜的温度场分布和位移场分布;在有限元分析软件中建立数值计算模型,并计算了不同厚度、直径尺寸下的温度场和位移场,得到了热变形随厚度尺寸和直径尺寸变化的规律。结果表明,影响白宝石高反镜反射面峰谷值变化的主要因素是温度,而尺寸变化对温度和刚度均有影响;选择合适的高反镜直径和厚度尺寸,可以有效降低镜面温升,同时得到合适的轴向结构刚度,从而减小反射镜镜面热变形。该研究结果对强光辐照下白宝石高反镜尺寸设计和选择具有一定的参考价值。%In order to reduce thermal deformation of high reflectance sapphire mirrors under high power laser irradiation and improve the beam quality , effect of the diameter and thickness on thermal deformation of the high reflectance mirror was studied .The heat conduction equation expressed in polar coordinate and the thermal deformation formula were used to describe the distribution of the temperature field and the displacement field of the sapphire mirror .Then, the numerical calculation model was built with the finite element analysis software and the temperature field and displacement field in different thickness and diameter was calculated .The thermal deformation with respect to the thickness and diameter was obtained .The results indicate that the main factors affecting the PV value of the sapphire mirror surface is the temperature variation and the change of the size has effect on both temperature and stiffness .Appropriate size and thickness effectively reduce the rise of mirror ’ s temperature and keep suitable axial structural stiffness , and thus the thermal deformation of the

  19. Registering prostate external beam radiotherapy with a boost from high-dose-rate brachytherapy: a comparative evaluation of deformable registration algorithms.

    Science.gov (United States)

    Moulton, Calyn R; House, Michael J; Lye, Victoria; Tang, Colin I; Krawiec, Michele; Joseph, David J; Denham, James W; Ebert, Martin A

    2015-12-14

    Registering CTs for patients receiving external beam radiotherapy (EBRT) with a boost dose from high-dose-rate brachytherapy (HDR) can be challenging due to considerable image discrepancies (e.g. rectal fillings, HDR needles, HDR artefacts and HDR rectal packing materials). This study is the first to comparatively evaluate image processing and registration methods used to register the rectums in EBRT and HDR CTs of prostate cancer patients. The focus is on the rectum due to planned future analysis of rectal dose-volume response. For 64 patients, the EBRT CT was retrospectively registered to the HDR CT with rigid registration and non-rigid registration methods in VelocityAI. Image processing was undertaken on the HDR CT and the rigidly-registered EBRT CT to reduce the impact of discriminating features on alternative non-rigid registration methods applied in the software suite for Deformable Image Registration and Adaptive Radiotherapy Research (DIRART) using the Horn-Schunck optical flow and Demons algorithms. The propagated EBRT-rectum structures were compared with the HDR structure using the Dice similarity coefficient (DSC), Hausdorff distance (HD) and average surface distance (ASD). The image similarity was compared using mutual information (MI) and root mean squared error (MSE). The displacement vector field was assessed via the Jacobian determinant (JAC). The post-registration alignments of rectums for 21 patients were visually assessed. The greatest improvement in the median DSC relative to the rigid registration result was 35 % for the Horn-Schunck algorithm with image processing. This algorithm also provided the best ASD results. The VelocityAI algorithms provided superior HD, MI, MSE and JAC results. The visual assessment indicated that the rigid plus deformable multi-pass method within VelocityAI resulted in the best rectum alignment. The DSC, ASD and HD improved significantly relative to the rigid registration result if image processing was applied prior

  20. The effect of environment on the creep deformation of ultra-high purity nickel-chromium-iron alloys at 360 degrees Celcius

    Science.gov (United States)

    Paraventi, Denise Jean

    2000-10-01

    Steam generators in pressurized water nuclear power plants have experienced significant problems with intergranular stress corrosion cracking (IGSCC) on the inner diameter of steam generator tubing for over 25 years. In the course of research to understand IGSCC, it has been shown that creep deformation may play a significant role in the cracking of commercial Alloy 600 (Ni-16Cr-9Fe-0.03C). The primary water environment can cause decreases in creep resistance (i.e., faster creep rates, shorter time to failure, and higher creep strains). During corrosion under the conditions of interest, both hydrogen reduction and metal dissolution occur. One or both may contribute to the enhancement of creep. The purpose of this work was to isolate the mechanism by which the water environment causes the creep deformation to increase. Activation area and activation enthalpy for glide were measured in argon and primary water on high purity Ni-16Cr-9Fe alloys. The results indicated that the activation area was reduced by primary water, consistent with a hydrogen enhanced plasticity mechanism for enhanced creep. The stress dependence of creep was also examined in argon and primary water. The results indicated that the internal stress of the alloy is reduced by the primary water environment. Lower internal stress is consistent with both a hydrogen model as well as a vacancy-aided climb model for enhanced creep. To isolate the effect of hydrogen on the creep of the alloy, experiments were conducted in a dissociated hydrogen environment. The results indicated that hydrogen would only increase the steady state creep rate if present before loading of the samples. However, if the sample was already in steady state creep and hydrogen introduced, a transient in the creep strain was observed. The creep rate returned to the original steady state rate in a short time. The results indicate that while hydrogen does affect the steady state creep to an extent, hydrogen cannot completely account for

  1. High-Temperature Deformation Behavior of a Ti-6Al-7Nb Alloy in Dual-Phase (α + β) and Single-Phase (β) Regions

    Science.gov (United States)

    Pilehva, F.; Zarei-Hanzaki, A.; Moemeni, S.; Khalesian, A. R.

    2016-01-01

    The present study aimed to characterizing the microstructure evolution of a Ti-6Al-7Nb biomedical type titanium alloy during hot working through hot compression tests. The hot deformation cycles were conducted under the strain rate of 0.0025, 0.025, and 0.25 s-1 in the temperature range of 850-1150 °C where both dual-phase (α + β) and single-phase (β) regions could be accessible. The flow stress behavior of the material for the entire deformation regime was interpreted via microstructural observations. The results indicated that in the single-phase β region (1050-1150 °C), the dynamically recrystallized (DRX) grains were formed at the deformed and elongated beta grain boundaries as a necklace-like structure. The variations in the dynamically recrystallized grain size were determined to follow the Zener-Hollomon relationship where DRX grain size was decreased by reducing the temperature and increasing the strain rate. The alloy deformation characteristics in α + β region were somewhat different. During deformation in the upper α + β temperature range (e.g., 1000 °C), the β phase would accommodate most of the deformation, while α regions remained undeformed. In the lower α + β temperature range (e.g., 850-950 °C), the kinking/bending of α lamellae as well as the subsequent globularization of α layers were postulated to be responsible for the observed flow softening behavior.

  2. Investigating the deformation of upper crustal faults at the N-Chilean convergent plate boundary at different scales using high-resolution topography datasets and creepmeter measurements

    Science.gov (United States)

    Ewiak, O.; Victor, P.; Ziegenhagen, T.; Oncken, O.

    2012-04-01

    The Chilean convergent plate boundary is one of the tectonically most active regions on earth and prone to large megathrust earthquakes as e. g. the 2010 Mw 8.8 Maule earthquake which ruptured a mature seismic gap in south-central Chile. In northern Chile historical data suggests the existence of a seismic gap between Arica and Mejillones Peninsula (MP), which has not ruptured since 1877. Further south, the 1995 Mw 8.0 Antofagasta earthquake ruptured the subduction interface between MP and Taltal. In this study we investigate the deformation at four active upper plate faults (dip-slip and strike-slip) located above the coupling zone of the subduction interface. The target faults (Mejillones Fault - MF, Salar del Carmen Fault - SCF, Cerro Fortuna Fault - CFF, Chomache Fault - CF) are situated in forearc segments, which are in different stages of the megathrust seismic cycle. The main question of this study is how strain is accumulated in the overriding plate, what is the response of the target faults to the megathrust seismic cycle and what are the mechanisms / processes involved. The hyper arid conditions of the Atacama desert and the extremely low erosion rates enable us to investigate geomorphic markers, e .g. fault scarps and knickpoints, which serve as a record for upper crustal deformation and fault activity about ten thousands years into the past. Fault scarp data has been acquired with Differential-GPS by measuring high-resolution topographic profiles perpendicular to the fault scarps and along incised gullies. The topographic data show clear variations between the target faults which possibly result from their position within the forearc. The surveyed faults, e. g. the SCF, exhibit clear along strike variations in the morphology of surface ruptures attributed to seismic events and can be subdivided into individual segments. The data allows us to distinguish single, composite and multiple fault scarps and thus to detect differences in fault growth initiated

  3. Elastic Properties in Tension and Shear of High Strength Nonferrous Metals and Stainless Steel - Effect of Previous Deformation and Heat Treatment

    Science.gov (United States)

    Mebs, R W; Mcadam, D J

    1947-01-01

    A resume is given of an investigation of the influence of plastic deformation and of annealing temperature on the tensile and shear elastic properties of high strength nonferrous metals and stainless steels in the form of rods and tubes. The data were obtained from earlier technical reports and notes, and from unpublished work in this investigation. There are also included data obtained from published and unpublished work performed on an independent investigation. The rod materials, namely, nickel, monel, inconel, copper, 13:2 Cr-Ni steel, and 18:8 Cr-Ni steel, were tested in tension; 18:8 Cr-Ni steel tubes were tested in shear, and nickel, monel, aluminum-monel, and Inconel tubes were tested in both tension and shear. There are first described experiments on the relationship between hysteresis and creep, as obtained with repeated cyclic stressing of annealed stainless steel specimens over a constant load range. These tests, which preceded the measurements of elastic properties, assisted in devising the loading time schedule used in such measurements. From corrected stress-set curves are derived the five proof stresses used as indices of elastic or yield strength. From corrected stress-strain curves are derived the secant modulus and its variation with stress. The relationship between the forms of the stress-set and stress-strain curves and the values of the properties derived is discussed. Curves of variation of proof stress and modulus with prior extension, as obtained with single rod specimens, consist in wavelike basic curves with superposed oscillations due to differences of rest interval and extension spacing; the effects of these differences are studied. Oscillations of proof stress and modulus are generally opposite in manner. The use of a series of tubular specimens corresponding to different amounts of prior extension of cold reduction gave curves almost devoid of oscillation since the effects of variation of rest interval and extension spacing were

  4. Mechanical Deformation of Sintered Porous Ag Die Attach at High Temperature and Its Size Effect for Wide-Bandgap Power Device Design

    Science.gov (United States)

    Chen, Chuantong; Nagao, Shijo; Zhang, Hao; Jiu, Jinting; Sugahara, Tohru; Suganuma, Katsuaki; Iwashige, Tomohito; Sugiura, Kazuhiko; Tsuruta, Kazuhiro

    2016-12-01

    The mechanical properties of sintered Ag paste with microporous structure have been investigated by tensile and shear tests, focusing on the temperature-dependent plastic deformation at various temperatures from 25°C to 300°C, corresponding to the target operating temperature range of emerging wide-bandgap semiconductor devices. Specimens were prepared by sintering hybrid Ag paste consisting of microflake and submicron spherical Ag particles, simulating a typical bonding process for power semiconductor die attach. Mechanical tests revealed that the unique microstructure caused a brittle-to-ductile transition at temperature of around 160°C, remarkably lower than that of bulk Ag. The obtained Young's modulus and shear modulus values indicate obvious softening with increasing temperature, together with a remarkable decrease in Poisson's ratio. These plastic behaviors at elevated temperature can be explained based on Coble creep in the microporous network structure. Fracture surfaces after tensile and shear tests indicated unique features on scanning electron microscopy, reflecting the variation in the ductile behavior with the test temperature. Furthermore, these temperature-dependent mechanical parameters were employed in three-dimensional finite-element analysis of the thermomechanical stress distribution in wide-bandgap semiconductor module structures including Ag paste die attach of different sizes. Detailed thermal stress analysis enabled precise evaluation of the packaging design for wide-bandgap semiconductor modules for use in high-temperature applications.

  5. Mechanical Deformation of Sintered Porous Ag Die Attach at High Temperature and Its Size Effect for Wide-Bandgap Power Device Design

    Science.gov (United States)

    Chen, Chuantong; Nagao, Shijo; Zhang, Hao; Jiu, Jinting; Sugahara, Tohru; Suganuma, Katsuaki; Iwashige, Tomohito; Sugiura, Kazuhiko; Tsuruta, Kazuhiro

    2017-03-01

    The mechanical properties of sintered Ag paste with microporous structure have been investigated by tensile and shear tests, focusing on the temperature-dependent plastic deformation at various temperatures from 25°C to 300°C, corresponding to the target operating temperature range of emerging wide-bandgap semiconductor devices. Specimens were prepared by sintering hybrid Ag paste consisting of microflake and submicron spherical Ag particles, simulating a typical bonding process for power semiconductor die attach. Mechanical tests revealed that the unique microstructure caused a brittle-to-ductile transition at temperature of around 160°C, remarkably lower than that of bulk Ag. The obtained Young's modulus and shear modulus values indicate obvious softening with increasing temperature, together with a remarkable decrease in Poisson's ratio. These plastic behaviors at elevated temperature can be explained based on Coble creep in the microporous network structure. Fracture surfaces after tensile and shear tests indicated unique features on scanning electron microscopy, reflecting the variation in the ductile behavior with the test temperature. Furthermore, these temperature-dependent mechanical parameters were employed in three-dimensional finite-element analysis of the thermomechanical stress distribution in wide-bandgap semiconductor module structures including Ag paste die attach of different sizes. Detailed thermal stress analysis enabled precise evaluation of the packaging design for wide-bandgap semiconductor modules for use in high-temperature applications.

  6. Modeling of High-Strain-Rate Deformation, Fracture, and Impact Behavior of Advanced Gas Turbine Engine Materials at Low and Elevated Temperatures

    Science.gov (United States)

    Shazly, Mostafa; Nathenson, David; Prakash, Vikas

    2003-01-01

    Gamma titanium aluminides have received considerable attention over the last decade. These alloys are known to have low density, good high temperature strength retention, and good oxidation and corrosion resistance. However, poor ductility and low fracture toughness have been the key limiting factors in the full utilization of these alloys. More recently, Gamma-met PX has been developed by GKSS, Germany. These alloys have been observed to have superior strengths at elevated temperatures and quasi-static deformation rates and good oxidation resistance at elevated temperatures when compared with other gamma titanium aluminides. The present paper discusses results of a study to understand dynamic response of gamma-met PX in uniaxial compression. The experiments were conducted by using a modified split Hopkinson pressure bar between room temperature and 900 C and strain rates of up to 3500 per second. The Gamma met PX alloy showed superior strength when compared to nickel based superalloys and other gamma titanium aluminides at all test temperatures. It also showed strain and strain-rate hardening at all levels of strain rates and temperatures and without yield anomaly up to 900 C. After approximately 600 C, thermal softening is observed at all strain rates with the rate of thermal softening increasing dramatically between 800 and 900 C. However, these flow stress levels are comparatively higher in Gamma met PX than those observed for other TiAl alloys.

  7. Revealing Hidden Deformation Sources in New Zealand: a Novel Inversion of GPS Data for Non-Prescriptive Physics-Based Surface Forces and High-Precision Strain Rates

    Science.gov (United States)

    Dimitrova, L. L.; Haines, A. J.; Wallace, L. M.; Williams, C. A.

    2013-12-01

    Monitoring strain accumulation in active deformation zones is vital for studying and preparing for earthquake hazards. New Zealand straddles the complicated boundary between the obliquely converging Australian and Pacific plates. The motion is accommodated largely along the Alpine Fault in the south, through the Marlborough fault system and onto the Hikurangi trench in the north. In addition, a significant component of the motion is distributed on smaller, poorly characterized faults. Dimitrova et al. (2012) showed that the vertical derivatives of horizontal stress (VDoHS) rates are a substantially higher resolution expression of subsurface sources of ongoing deformation than the GPS velocities or GPS derived strain rates. We expand this method to solve the horizontal force balance equations for the VDoHS in 2-D to obtain the highest possible resolution picture of the surface deformation pattern in New Zealand. We invert GPS data from campaign GPS observations spanning from 1995 to 2012 for the VDoHS that best fit the GPS velocities, without prescribing sources or zones of deformation, while fully accounting for the physics of the problem. Using the VDoHS rates we identify (1) areas of deformation due to well-known active faults, (2) areas of poorly characterized deformation, e.g. deformation along faults without slip rate information mapped from palaeo-seismicity, (3) areas of previously unknown deformation, potentially on hidden faults, and (4) areas undergoing post-seismic deformation. The VDoHS are integrated to produce the highest resolution to-date maps of strain rates. We identify an area of extensional areal strain between the Alpine fault and the Main Divide of the central Southern Alps indicating possible gravitational collapse of the Southern Alps. Relationships between the VDoHS and strain rates allow us to calculate the variation in fault slip rate and locking depth for the identified faults, and we show selected results for the Alpine Fault and the

  8. -Deformed nonlinear maps

    Indian Academy of Sciences (India)

    Ramaswamy Jaganathan; Sudeshna Sinha

    2005-03-01

    Motivated by studies on -deformed physical systems related to quantum group structures, and by the elements of Tsallis statistical mechanics, the concept of -deformed nonlinear maps is introduced. As a specific example, a -deformation procedure is applied to the logistic map. Compared to the canonical logistic map, the resulting family of -logistic maps is shown to have a wider spectrum of interesting behaviours, including the co-existence of attractors – a phenomenon rare in one-dimensional maps.

  9. Alar Rim Deformities.

    Science.gov (United States)

    Totonchi, Ali; Guyuron, Bahman

    2016-01-01

    The alar rim plays an important role in nasal harmony. Alar rim flaws are common following the initial rhinoplasty. Classification of the deformities helps with diagnosis and successful surgical correction. Diagnosis of the deformity requires careful observation of the computerized or life-sized photographs. Techniques for treatment of these deformities can easily be learned with attention to detail. Copyright © 2016 Elsevier Inc. All rights reserved.

  10. Fluctuations as stochastic deformation

    Science.gov (United States)

    Kazinski, P. O.

    2008-04-01

    A notion of stochastic deformation is introduced and the corresponding algebraic deformation procedure is developed. This procedure is analogous to the deformation of an algebra of observables like deformation quantization, but for an imaginary deformation parameter (the Planck constant). This method is demonstrated on diverse relativistic and nonrelativistic models with finite and infinite degrees of freedom. It is shown that under stochastic deformation the model of a nonrelativistic particle interacting with the electromagnetic field on a curved background passes into the stochastic model described by the Fokker-Planck equation with the diffusion tensor being the inverse metric tensor. The first stochastic correction to the Newton equations for this system is found. The Klein-Kramers equation is also derived as the stochastic deformation of a certain classical model. Relativistic generalizations of the Fokker-Planck and Klein-Kramers equations are obtained by applying the procedure of stochastic deformation to appropriate relativistic classical models. The analog of the Fokker-Planck equation associated with the stochastic Lorentz-Dirac equation is derived too. The stochastic deformation of the models of a free scalar field and an electromagnetic field is investigated. It turns out that in the latter case the obtained stochastic model describes a fluctuating electromagnetic field in a transparent medium.

  11. Deformed discrete symmetries

    Science.gov (United States)

    Arzano, Michele; Kowalski-Glikman, Jerzy

    2016-09-01

    We construct discrete symmetry transformations for deformed relativistic kinematics based on group valued momenta. We focus on the specific example of κ-deformations of the Poincaré algebra with associated momenta living on (a sub-manifold of) de Sitter space. Our approach relies on the description of quantum states constructed from deformed kinematics and the observable charges associated with them. The results we present provide the first step towards the analysis of experimental bounds on the deformation parameter κ to be derived via precision measurements of discrete symmetries and CPT.

  12. Fabrics and deformational mechanisms in the high-pressure granulite of the Bacariza Formation (Cabo Ortegal Complex, NW Spain); Fabricas y mecanismos deformacionales en las granulitas de alta presion de la Formacion Bacariza (Complejo de Cabo Ortegal, NO de Espana)

    Energy Technology Data Exchange (ETDEWEB)

    Puelles, P.

    2009-07-01

    In the Cabo Ortegal Complex, mylonitic high-pressure granulites occur at the contacts between the HP granulitic Bacariza Formation and the adjacent units. This mylonitic stage is associated with the initial exhumation of the complex. The petrographic, microstructural and crystallographic analysis of the main constituent minerals in these rocks might provide valuable information on the deformation mechanisms operative at depth. Garnet accommodated part of the deformation by dislocation creep and rigid rotation, augite underwent dislocation creep accompanied by mass transfer and anisotropic growth while plagioclase, in turn, suffered dynamic subgrain rotation-recrystallization and climb-accommodated dislocation creep. Quartz fabrics developed under at least amphibolite-facies conditions. The shear sense criteria are consistent with a top-to-the-NE displacement of the hanging wall blocks. During their ascent to the surface, a static amphibolite-facies retrogressive stage was followed by plastic deformation accommodation under green schist- to lower amphibolite facies conditions. Deformation during the latest stages of exhumation was characterized by micro fracturing and seismic activity in conditions of high differential stresses and strain rates. (Author) 52 refs.

  13. Implementation of an Associative Flow Rule Including Hydrostatic Stress Effects Into the High Strain Rate Deformation Analysis of Polymer Matrix Composites

    Science.gov (United States)

    Goldberg, Robert K.; Roberts, Gary D.; Gilat, Amos

    2003-01-01

    A previously developed analytical formulation has been modified in order to more accurately account for the effects of hydrostatic stresses on the nonlinear, strain rate dependent deformation of polymer matrix composites. State variable constitutive equations originally developed for metals have been modified in order to model the nonlinear, strain rate dependent deformation of polymeric materials. To account for the effects of hydrostatic stresses, which are significant in polymers, the classical J2 plasticity theory definitions of effective stress and effective inelastic strain, along with the equations used to compute the components of the inelastic strain rate tensor, are appropriately modified. To verify the revised formulation, the shear and tensile deformation of two representative polymers are computed across a wide range of strain rates. Results computed using the developed constitutive equations correlate well with experimental data. The polymer constitutive equations are implemented within a strength of materials based micromechanics method to predict the nonlinear, strain rate dependent deformation of polymer matrix composites. The composite mechanics are verified by analyzing the deformation of a representative polymer matrix composite for several fiber orientation angles across a variety of strain rates. The computed values compare well to experimentally obtained results.

  14. Intracrystalline deformation of calcite

    NARCIS (Netherlands)

    de Bresser, Hans

    1991-01-01

    It is well established from observations on natural calcite tectonites that intracrystalline plastic mechanisms are important during the deformation of calcite rocks in nature. In this thesis, new data are presented on fundamental aspects of deformation behaviour of calcite under conditions where 'd

  15. Resurgent deformation quantisation

    Energy Technology Data Exchange (ETDEWEB)

    Garay, Mauricio, E-mail: garay91@gmail.com [Institut für Mathematik, FB 08 Physik, Mathematik und Informatik, Johannes Gutenberg-Universität, 55099 Mainz (Germany); Goursac, Axel de, E-mail: Axelmg@melix.net [Chargé de Recherche au F.R.S.-FNRS, IRMP, Université Catholique de Louvain, Chemin du Cyclotron, 2, B-1348 Louvain-la-Neuve (Belgium); Straten, Duco van, E-mail: straten@mathematik.uni-mainz.de [Institut für Mathematik, FB 08 Physik, Mathematik und Informatik, Johannes Gutenberg-Universität, 55099 Mainz (Germany)

    2014-03-15

    We construct a version of the complex Heisenberg algebra based on the idea of endless analytic continuation. The algebra would be large enough to capture quantum effects that escape ordinary formal deformation quantisation. -- Highlights: •We construct resurgent deformation quantisation. •We give integral formulæ. •We compute examples which show that hypergeometric functions appear naturally in quantum computations.

  16. High-velocity deformation of Al0.3CoCrFeNi high-entropy alloy: Remarkable resistance to shear failure

    Science.gov (United States)

    Li, Z.; Zhao, S.; Diao, H.; Liaw, P. K.; Meyers, M. A.

    2017-01-01

    The mechanical behavior of a single phase (fcc) Al0.3CoCrFeNi high-entropy alloy (HEA) was studied in the low and high strain-rate regimes. The combination of multiple strengthening mechanisms such as solid solution hardening, forest dislocation hardening, as well as mechanical twinning leads to a high work hardening rate, which is significantly larger than that for Al and is retained in the dynamic regime. The resistance to shear localization was studied by dynamically-loading hat-shaped specimens to induce forced shear localization. However, no adiabatic shear band could be observed. It is therefore proposed that the excellent strain hardening ability gives rise to remarkable resistance to shear localization, which makes this material an excellent candidate for penetration protection applications such as armors. PMID:28210000

  17. High-velocity deformation of Al0.3CoCrFeNi high-entropy alloy: Remarkable resistance to shear failure

    Science.gov (United States)

    Li, Z.; Zhao, S.; Diao, H.; Liaw, P. K.; Meyers, M. A.

    2017-02-01

    The mechanical behavior of a single phase (fcc) Al0.3CoCrFeNi high-entropy alloy (HEA) was studied in the low and high strain-rate regimes. The combination of multiple strengthening mechanisms such as solid solution hardening, forest dislocation hardening, as well as mechanical twinning leads to a high work hardening rate, which is significantly larger than that for Al and is retained in the dynamic regime. The resistance to shear localization was studied by dynamically-loading hat-shaped specimens to induce forced shear localization. However, no adiabatic shear band could be observed. It is therefore proposed that the excellent strain hardening ability gives rise to remarkable resistance to shear localization, which makes this material an excellent candidate for penetration protection applications such as armors.

  18. Deformation Measurements of Smart Aerodynamic Surfaces

    Science.gov (United States)

    Fleming, Gary A.; Burner, Alpheus

    2005-01-01

    Video Model Deformation (VMD) and Projection Moire Interferometry (PMI) were used to acquire wind tunnel model deformation measurements of the Northrop Grumman-built Smart Wing tested in the NASA Langley Transonic Dynamics Tunnel. The F18-E/F planform Smart Wing was outfitted with embedded shape memory alloys to actuate a seamless trailing edge aileron and flap, and an embedded torque tube to generate wing twist. The VMD system was used to obtain highly accurate deformation measurements at three spanwise locations along the main body of the wing, and at spanwise locations on the flap and aileron. The PMI system was used to obtain full-field wing shape and deformation measurements over the entire wing lower surface. Although less accurate than the VMD system, the PMI system revealed deformations occurring between VMD target rows indistinguishable by VMD. This paper presents the VMD and PMI techniques and discusses their application in the Smart Wing test.

  19. Genu Recurvatum Deformity in a Child due to Salter Harris Type V Fracture of the Proximal Tibial Physis Treated with High Tibial Dome Osteotomy

    OpenAIRE

    Theodoros Beslikas; Andreas Christodoulou; Anastasios Chytas; Ioannis Gigis; John Christoforidis

    2012-01-01

    Salter-Harris type V fracture is a very rare injury in the immature skeleton. In most cases, it remains undiagnosed and untreated. We report a case of genu recurvatum deformity in a 15-year-old boy caused by a Salter-Harris type V fracture of the proximal tibial physis. The initial X-ray did not reveal fracture. One year after injury, genu recurvatum deformity was detected associated with significant restriction of knee flexion and limp length discrepancy (2 cm) as well as medial and posterio...

  20. Deformations of Superconformal Theories

    CERN Document Server

    Cordova, Clay; Intriligator, Kenneth

    2016-01-01

    We classify possible supersymmetry-preserving relevant, marginal, and irrelevant deformations of unitary superconformal theories in $d \\geq 3$ dimensions. Our method only relies on symmetries and unitarity. Hence, the results are model independent and do not require a Lagrangian description. Two unifying themes emerge: first, many theories admit deformations that reside in multiplets together with conserved currents. Such deformations can lead to modifications of the supersymmetry algebra by central and non-central charges. Second, many theories with a sufficient amount of supersymmetry do not admit relevant or marginal deformations, and some admit neither. The classification is complicated by the fact that short superconformal multiplets display a rich variety of sporadic phenomena, including supersymmetric deformations that reside in the middle of a multiplet. We illustrate our results with examples in diverse dimensions. In particular, we explain how the classification of irrelevant supersymmetric deformat...

  1. Massey products and deformations

    CERN Document Server

    Fuchs, D; Fuchs, Dmitry; Lang, Lynelle

    1996-01-01

    The classical deformation theory of Lie algebras involves different kinds of Massey products of cohomology classes. Even the condition of extendibility of an infinitesimal deformation to a formal one-parameter deformation of a Lie algebra involves Massey powers of two dimensional cohomology classes which are not powers in the usual definition of Massey products in the cohomology of a differential graded Lie algebra. In the case of deformations with other local bases, one deals with other, more specific Massey products. In the present work a construction of generalized Massey products is given, depending on an arbitrary graded commutative, associative algebra. In terms of these products, the above condition of extendibility is generalized to deformations with arbitrary local bases. Dually, a construction of generalized Massey products on the cohomology of a differential graded commutative associative algebra depends on a nilpotent graded Lie algebra. For example, the classical Massey products correspond to the...

  2. Spatiotemporal deformations of reflectionless potentials

    Science.gov (United States)

    Horsley, S. A. R.; Longhi, S.

    2017-08-01

    Reflectionless potentials for classical or matter waves represent an important class of scatteringless systems encountered in different areas of physics. Here we mathematically demonstrate that there is a family of non-Hermitian potentials that, in contrast to their Hermitian counterparts, remain reflectionless even when deformed in space or time. These are the profiles that satisfy the spatial Kramers-Kronig relations. We start by considering scattering of matter waves for the Schrödinger equation with an external field, where a moving potential is observed in the Kramers-Henneberger reference frame. We then generalize this result to the case of electromagnetic waves, by considering a slab of reflectionless material that both is scaled and has its center displaced as an arbitrary function of position. We analytically and numerically demonstrate that the backscattering from these profiles remains zero, even for extreme deformations. Our results indicate the supremacy of non-Hermitian Kramers-Kronig potentials over reflectionless Hermitian potentials in keeping their reflectionless property under deformation and could find applications to, e.g., reflectionless optical coatings of highly deformed surfaces based on perfect absorption.

  3. Driver ASICs for Advanced Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The program leverages on our extensive expertise in developing high-performance driver ASICs for deformable mirror systems and seeks to expand the capacities of the...

  4. High resolution deformation maps of Volcán de Colima, Mexico, derived from a year-long TerraSAR-X Spotlight time series

    Science.gov (United States)

    Salzer, Jacqueline; Nikkhoo, Mehdi; Walter, Thomas R.

    2015-04-01

    Volcán de Colima is a steep sloped explosive stratovolcano located in southern Central Mexico, and one of the most active volcanoes in North America. Major recent historical eruptions occured in 1818 (VEI 4) and 1913 (VEI 5), which removed several hundred meters from the summit of the volcanic edifice [1], and point towards the activity being marked by 100-year cycles which terminate in a large Plinian eruption. Also, five large flank collapse events have been identified during the Holocene [2]. Since the beginning of the most recent eruptiove period in 1998, the type of activity has been varying between predominantly explosive, dome building and dome collapse. Between 2007 and 2011, the activity at Colima was characterized by dome extrusion. The volcano then entered a period of low activity, which lasted until January 2013, when a series of explosions took place which initiated a new, still ongoing period of dome growth. The historical eruption of 1913, as well as the renewal of the activity in 2013, were both preceeded by longer periods of low activity, and only very limited short term precursors. The year 2012 at Volcán de Colima is therefore a good example to study volcanic activity in periods of quiescence, but leading up to an eruption. Furthermore, the possibility of a larger event in the future make it a particularly important volcano to study. We have acquired TerraSAR-X data in spotlight mode for ascending and descending tracks over Colima, obtaining a high spatial resolution of up to 2 m, and a temporal resolution of up to 11 days. Here we present the time series of the dome deformation between February and December 2012. We generated interferograms using an updated version of DORIS, accounting for the doppler variation in along track direction [3] and subsequently analysed the time series of the deformation pattern with the small baseline - persistent scatterer (PS) approach implemented in the StaMPS software. We removed the topographically correlated

  5. Effects of Deformation on Bainite Transformation During Continuous Cooling of Low Carbon Steels

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Hot deformation experiments were carried out on Gleeble 1500 thermo-mechanical simulator. The bainite transformation after deformation was investigated by optical microstructure analysis. The results indicated that the deformation accelerated the bainite transformation when the deformation was carried out at high temperature and no or little ferrite was precipitated before bainite transformation; when the deformation was carried out at low temperature, the deformation hindered the bainite transformation because a lot of ferrite precipitated before bainite transformation.

  6. Microstructural Analysis of Orientation-Dependent Recovery and Recrystallization in a Modified 9Cr-1Mo Steel Deformed by Compression at a High Strain Rate

    DEFF Research Database (Denmark)

    Zhang, Zhenbo; Zhang, Yubin; Mishin, Oleg

    2016-01-01

    The evolution of the microstructure and texture during annealing of a modified ferritic/martensitic 9Cr-1Mo steel compressed by dynamic plastic deformation (DPD) to a strain of 2.3 has been investigated using transmission electron microscopy and electron backscatter diffraction. It is found...

  7. High spin structures in the $A\\approx 40$ mass region: from superdeformation to extreme deformation and clusterization (an example of $^{28}$Si)

    CERN Document Server

    Afanasjev, A V

    2016-01-01

    The search for extremely deformed structures in the yrast and near-yrast region of $^{28}$Si has been performed within the cranked relativistic mean field theory up to spin $I=20\\hbar$. The fingerprints of clusterization are seen (well pronounced) in the superdeformed (hyperdeformed) configurations.

  8. An investigation of pairing correlations in diabatic configurations at high spin and large deformation applications to the description of SD bands in sup 1 sup 4 sup 3 Eu

    CERN Document Server

    Axelsson, A; Nyberg, J

    2002-01-01

    The HFB cranked shell model is applied in an investigation of the selfconsistent pairing properties of the superdeformed (SD) bands in sup 1 sup 4 sup 3 Eu. Results from a fully pairing and deformation selfconsistent mesh calculation of the properties of the most intense SD band in sup 1 sup 4 sup 3 Eu are presented, as well as pairing selfconsistent calculations done at a fixed deformation close to the SD minimum for an excited SD configuration. The calculations are compared to unpaired calculations and to published experimental data. Fully diabatic configurations are studied and total energy surfaces are constructed for fixed values of the angular momentum. Other issues addressed include the development of the particle number distribution in the HFB wave function up to very high frequency, the consequences of using a fixed Fermi energy in high-spin calculations and the effects of the number of excited quasiparticles on the pairing properties of the superdeformed nucleus.

  9. Comparative Analysis of the Effects of Severe Plastic Deformation and Thermomechanical Training on the Functional Stability of Ti50.5Ni24.5Pd25 High-Temperature Shape Memory Alloy

    Science.gov (United States)

    Atli, K. C.; Karaman, I.; Noebe, R. D.; Maier, H. J.

    2010-01-01

    We compare the effectiveness of a conventional thermomechanical training procedure and severe plastic deformation via equal channel angular extrusion to achieve improved functional stability in a Ti50.5Ni24.5Pd25 high-temperature shape memory alloy. Thermomechanical testing indicates that both methods result in enhanced shape memory characteristics, such as reduced irrecoverable strain and thermal hysteresis. The mechanisms responsible for the improvements are discussed in light of microstructural findings from transmission electron microscopy.

  10. Comparative Analysis of the Effects of Severe Plastic Deformation and Thermomechanical Training on the Functional Stability of Ti50.5Ni24.5Pd25 High-Temperature Shape Memory Alloy

    Science.gov (United States)

    Atli, K. C.; Karaman, I.; Noebe, R. D.; Maier, H. J.

    2010-01-01

    We compare the effectiveness of a conventional thermomechanical training procedure and severe plastic deformation via equal channel angular extrusion to achieve improved functional stability in a Ti50.5Ni24.5Pd25 high-temperature shape memory alloy. Thermomechanical testing indicates that both methods result in enhanced shape memory characteristics, such as reduced irrecoverable strain and thermal hysteresis. The mechanisms responsible for the improvements are discussed in light of microstructural findings from transmission electron microscopy.

  11. Improvements in high-field localized MRS of the medial temporal lobe in humans using new deformable high-dielectric materials.

    Science.gov (United States)

    Snaar, J E M; Teeuwisse, W M; Versluis, M J; van Buchem, M A; Kan, H E; Smith, N B; Webb, A G

    2011-08-01

    The intrinsic nonuniformities in the transmit radiofrequency field from standard quadrature volume resonators at high field are particularly problematic for localized MRS in areas such as the temporal lobe, where a low signal-to-noise ratio and poor metabolite quantification result from destructive B₁⁺ field interference, in addition to line broadening and signal loss from strong susceptibility gradients. MRS of the temporal lobe has been performed in a number of neurodegenerative diseases at clinical fields, but a relatively low signal-to-noise ratio has prevented the reliable quantification of, for example, glutamate and glutamine, which are thought to play a key role in disease progression. Using a recently developed high-dielectric-constant material placed around the head, localized MRS of the medial temporal lobe using the stimulated echo acquisition mode sequence was acquired at 7 T. The presence of the material increased the signal-to-noise ratio of MRS by a factor of two without significantly reducing the sensitivity in other areas of the brain, as shown by the measured B₁⁺ maps. An increase in the receive sensitivity B₁⁻ was also measured close to the pads. The spectral linewidth of the unsuppressed water peak within the voxel of interest was reduced slightly by the introduction of the dielectric pads (although not to a statistically significant degree), a result confirmed by using a pad composed of lipid. Using LCmodel for quantitative analysis of metabolite concentrations, the increase in signal-to-noise ratio and the slight decrease in spectral linewidth contributed to statistically significant reductions in the Cramer-Rao lower bounds (CRLBs), also allowing the levels of glutamate and glutamine to be quantified with CRLBs below 20%.

  12. The Spherical Deformation Model

    DEFF Research Database (Denmark)

    Hobolth, Asgar

    2003-01-01

    Miller et al. (1994) describe a model for representing spatial objects with no obvious landmarks. Each object is represented by a global translation and a normal deformation of a sphere. The normal deformation is defined via the orthonormal spherical-harmonic basis. In this paper we analyse...... the spherical deformation model in detail and describe how it may be used to summarize the shape of star-shaped three-dimensional objects with few parameters. It is of interest to make statistical inference about the three-dimensional shape parameters from continuous observations of the surface and from...

  13. Calcaneo-valgus deformity.

    Science.gov (United States)

    Evans, D

    1975-08-01

    A discussion of the essential deformity in calcaneo-valgus feet develops a theme originally put forward in 1961 on the relapsed club foot (Evans 1961). Whereas in the normal foot the medial and lateral columns are about equal in length, in talipes equino-varus the lateral column is longer and in calcaneo-valgus shorter than the medial column. The suggestion is that in the treatment of both deformities the length of the columns be made equal. A method is described of treating calcaneo-valgus deformity by inserting cortical bone grafts taken from the tibia to elongate the anterior end of the calcaneus.

  14. High-pressure, high-temperature deformation of CaGeO3 (perovskite)±MgO aggregates: Elasto-ViscoPlastic Self-Consistent modeling and dynamics in the lower mantle

    Science.gov (United States)

    Hilairet, Nadège; Tomé, Carlos; Wang, Huamiao; Merkel, Sébastien; Wang, Yanbin; Gasc, Julien; Feng, Shi; Nishiyama, Norimasa

    2016-04-01

    As the largest rocky layer in the Earth, the lower mantle plays a critical role in controlling convective patterns in our planet. Current mineralogical models suggest that the lower mantle is dominated by (Mg,Fe)SiO3 perovskite (SiPv; about 70 - 90% in volume fraction) and (Mg,Fe)O ferropericlase (Fp). Knowledge of rheological properties and textures of the major constituent minerals is critical in understanding dynamic processes of the deep Earth, and relating seismic observations to mineralogy. While individual properties of these phases have been studied, fewer informations on polyphase aggregates are available. Fundamental understanding about the stress-strain interactions among the phases and their effect on the bulk rheology still remains to be properly addressed. We examine stress/strain partitioning and rheological properties of a two-phase polycrystal CaGeO3 perovskite (GePv) and MgO, deformed in the D-DIA at controlled speed ~1 - 3×10-5 s-1 at high pressures and temperatures (between 3 to 10 GPa and 300 to 1200 K), with bulk axial strains up to ~30%. We use Elasto-Visco Plastic Self-Consistent modeling (EVPSC) to reproduce lattice strains and textures measured in-situ with synchrotron X-ray diffraction. We compare the results to those on an identical deformation experiment with a single phase (GePv) polycrystal. We will discuss stress distributions between the two phases in the composite, texture developments, relationships with active slip systems, and finally the implications for rheological and seismic properties of the lower mantle.

  15. 激光辐照下镀铬介质高吸收镜的热变形%Thermal deformation of high absorption chrome plated mirror irradiated by laser

    Institute of Scientific and Technical Information of China (English)

    聂山钧; 郭劲; 邵俊峰; 王挺峰; 汤伟

    2015-01-01

    In order to analyze the effect of thermal deformation of the mirror irradiated by laser beam on the beam quality , thermal-static structural coupled model of high absorption chrome plated mirror irradiated by la-ser beam with the incidence angle of 45°is built.Thermal deformation under different irradiation laser and the influence of mirror thickness on the deformation are analyzed .Then thermal deformation is detected with Hart-mann wavefront sensor on free boundary condition .The results show that thermal deformation increases approx-imately linearly with the increase of the power absorbed at the range of 0.085-0.185 W.When the diameter of the facula increases , the deformation decreases .When mirror's thickness keeps in the range of 1~5 mm, the deformation merely keeps constant .In the initial stage of laser irradiation , the temperature and deformation increase rapidly .After 20 s, the increase of temperature on the mirror becomes slowly .The deformation in-creases to 0.27 μm in 1 s, and then increase slowly .The deformation will reach balance after 100 s.When the irradiation laser is removed , the mirror will return to the initial state after 120 s.The analysis result shows that the testing error is mainly caused by the error of the diameter of the facula and the incident angle of the la -ser .%为了分析激光辐照下反射镜热变形对光束质量的影响,本文建立了激光光束45°角入射时镀铬介质高吸收镜的热固耦合模型,对不同辐照光束下反射镜的热变形和镜体厚度对热变形的影响进行了分析,并用哈特曼波前传感器对自由边界条件下的镜面热变形进行了检测。结果表明:吸收功率在0.085~0.185 W时,镜面热变形随吸收功率的增加近似线性增加,随辐照光斑的增加而减小;反射镜厚度在1~5 mm范围,镜面热变形基本不变。在激光照射的初始阶段,反射镜表面温度和热变形迅速增加,在激光连续照射20 s后

  16. Research on monitoring system for slope deformation

    Institute of Scientific and Technical Information of China (English)

    LIU Xiao-sheng; ZHANG Xue-zhuang; WANG Ai-gong

    2007-01-01

    The monitoring system for slope deformation which bases on Leica (TCA series)was researched and developed. This system consists of electronic total stations, high precision thermometer, digital barometer, photoelectric frequency adjustor and other related instruments and data collection and processing software. The system can monitor a series of targets automatically to obtain accurate data of distance at predetermined time, besides,it can timely display targets' coordinates and deformation value, velocity, etc. in graph as well. To compare of the results of different monitoring time, we can find the problems of mine slope deformation rapidly and accurately.

  17. Deformations of singularities

    CERN Document Server

    Stevens, Jan

    2003-01-01

    These notes deal with deformation theory of complex analytic singularities and related objects. The first part treats general theory. The central notion is that of versal deformation in several variants. The theory is developed both in an abstract way and in a concrete way suitable for computations. The second part deals with more specific problems, specially on curves and surfaces. Smoothings of singularities are the main concern. Examples are spread throughout the text.

  18. Diffeomorphic Statistical Deformation Models

    DEFF Research Database (Denmark)

    Hansen, Michael Sass; Hansen, Mads/Fogtman; Larsen, Rasmus

    2007-01-01

    In this paper we present a new method for constructing diffeomorphic statistical deformation models in arbitrary dimensional images with a nonlinear generative model and a linear parameter space. Our deformation model is a modified version of the diffeomorphic model introduced by Cootes et al. Th...... with ground truth in form of manual expert annotations, and compared to Cootes's model. We anticipate applications in unconstrained diffeomorphic synthesis of images, e.g. for tracking, segmentation, registration or classification purposes....

  19. Deformation in nanocrystalline metals

    OpenAIRE

    Helena Van Swygenhoven; Julia R. Weertman

    2006-01-01

    It is now possible to synthesize polycrystalline metals made up of grains that average less than 100 nm in size. Such nanocrystalline metals contain a significant volume fraction of interfacial regions separated by nearly perfect crystals. The small sizes involved limit the conventional operation of dislocation sources and thus a fundamental question arises: how do these materials deform plastically? We review the current views on deformation mechanisms in nanocrystalline, face-centered cubic...

  20. Microstructural Analysis of Orientation-Dependent Recovery and Recrystallization in a Modified 9Cr-1Mo Steel Deformed by Compression at a High Strain Rate

    Science.gov (United States)

    Zhang, Zhenbo; Zhang, Yubin; Mishin, Oleg V.; Tao, Nairong; Pantleon, Wolfgang; Juul Jensen, Dorte

    2016-09-01

    The evolution of the microstructure and texture during annealing of a modified ferritic/martensitic 9Cr-1Mo steel compressed by dynamic plastic deformation (DPD) to a strain of 2.3 has been investigated using transmission electron microscopy and electron backscatter diffraction. It is found that the duplex + fiber texture formed by DPD is transformed during annealing to a dominant fiber texture, and that crystallites of the component have an advantage during both nucleation and growth. Detailed characterization of the microstructural morphology, and estimation of the stored energies in - and -oriented regions in deformed and annealed samples, as well as investigations of the growth of recrystallizing grains, are used to analyze the annealing behavior. It is concluded that recrystallization in the given material occurs by a combination of oriented nucleation and oriented growth.

  1. Effect of Cold Deformation on the Friction-Wear Property of a Biomedical Nickel-Free High-Nitrogen Stainless Steel

    Institute of Scientific and Technical Information of China (English)

    Hao-Chuan Zhao; Yi-Bin Ren; Jia-Hui Dong; Xin-Min Fan; Ke Yang

    2016-01-01

    The microstructural,mechanical and corrosion properties of different cold-rolled biomedical nickel-free highnitrogen stainless steels (NFHNSSs) were investigated to study the effect of cold deformation on its dry wear resistance as well as corrosion-wear behaviors in distilled water and Hank's solution.The results indicated that NFHNSS was characterized by stable austenite and possessed excellent work-hardening capacity;due to increasing cold deformation,the corrosion resistance just decreased very slightly and the dry wear rate decreased initially but subsequently increased,while the corrosion-wear resistance was improved monotonically in both distilled water and Hank's solution in spite of the presence of corrosive ions.The friction coefficients for different cold-rolled NFHNSSs were very close under the same lubricating condition,but they were the largest in distilled water compared to that in dry wear tests and Hank's solution.

  2. Anomalous lattice deformation in GaN/SiC(0001) measured by high-speed in situ synchrotron X-ray diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, Takuo, E-mail: sasaki.takuo@jaea.go.jp; Takahasi, Masamitu [Quantum Beam Science Center, Japan Atomic Energy Agency, 1-1-1 Koto, Sayo, Hyogo 679-5148 (Japan); Ishikawa, Fumitaro [Graduate School of Science and Engineering, Ehime University, 3 Bunkyo-cho, Matsuyama 790-8577 (Japan)

    2016-01-04

    We report an anomalous lattice deformation of GaN layers grown on SiC(0001) by molecular beam epitaxy. The evolution of the lattice parameters during the growth of the GaN layers was measured by in situ synchrotron X-ray diffraction. The lattice parameters in the directions parallel and normal to the surface showed significant deviation from the elastic strains expected for lattice-mismatched films on substrates up to a thickness of 10 nm. The observed lattice deformation was well explained by the incorporation of hydrostatic strains due to point defects. The results indicate that the control of point defects in the initial stage of growth is important for fabricating GaN-based optoelectronic devices.

  3. More on analyzing the reflection of a laser beam by a deformed highly reflective volume Bragg grating using iteration of the beam propagation method.

    Science.gov (United States)

    Shu, Hong; Mokhov, Sergiy; Zeldovich, Boris Ya; Bass, Michael

    2009-01-01

    A further extension of the iteration method for beam propagation calculation is presented that can be applied for volume Bragg gratings (VBGs) with extremely large grating strength. A reformulation of the beam propagation formulation is presented for analyzing the reflection of a laser beam by a deformed VBG. These methods will be shown to be very accurate and efficient. A VBG with generic z-dependent distortion has been analyzed using these methods.

  4. Molecular deformation mechanisms in polyethylene

    CERN Document Server

    Coutry, S

    2001-01-01

    adjacent labelled stems is significantly larger when the DPE guest is a copolymer molecule. Our comparative studies on various types of polyethylene lead to the conclusion that their deformation behaviour under drawing has the same basis, with additional effects imputed to the presence of tie-molecules and branches. Three major points were identified in this thesis. The changes produced by drawing imply (1) the crystallisation of some of the amorphous polymer and the subsequent orientation of the newly formed crystals, (2) the re-orientation of the crystalline ribbons and (3) the beginning of crystallite break-up. However, additional effects were observed for the high molecular weight linear sample and the copolymer sample and were attributed, respectively, to the presence of tie-molecules and of branches. It was concluded that both the tie-molecules and the branches are restricting the molecular movement during deformation, and that the branches may be acting as 'anchors'. This work is concerned with details...

  5. Analytical modeling of the thermomechanical behavior of ASTM F-1586 high nitrogen austenitic stainless steel used as a biomaterial under multipass deformation.

    Science.gov (United States)

    Bernardes, Fabiano R; Rodrigues, Samuel F; Silva, Eden S; Reis, Gedeon S; Silva, Mariana B R; Junior, Alberto M J; Balancin, Oscar

    2015-06-01

    Precipitation-recrystallization interactions in ASTM F-1586 austenitic stainless steel were studied by means of hot torsion tests with multipass deformation under continuous cooling, simulating an industrial laminating process. Samples were deformed at 0.2 and 0.3 at a strain rate of 1.0s(-1), in a temperature range of 900 to 1200°C and interpass times varying from 5 to 80s. The tests indicate that the stress level depends on deformation temperature and the slope of the equivalent mean stress (EMS) vs. 1/T presents two distinct behaviors, with a transition at around 1100°C, the non-recrystallization temperature (Tnr). Below the Tnr, strain-induced precipitation of Z-phase (NbCrN) occurs in short interpass times (tpass<30s), inhibiting recrystallization and promoting stepwise stress build-up with strong recovery, which is responsible for increasing the Tnr. At interpass times longer than 30s, the coalescence and dissolution of precipitates promote a decrease in the Tnr and favor the formation of recrystallized grains. Based on this evidence, the physical simulation of controlled processing allows for a domain refined grain with better mechanical properties.

  6. Deformation, Phase Transformation and Recrystallization in the Shear Bands Induced by High-Strain Rate Loading in Titanium and Its Alloys

    Institute of Scientific and Technical Information of China (English)

    Yongbo XU; Yilong BAI; M.A.Meyers

    2006-01-01

    α-titanium and its alloys with a dual-phase structure (α+β) were deformed dynamically under strain rate of about 104 s-1. The formation and microstructural evolution of the localized shear bands were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results reveal that both the strain and strain rate should be considered simultaneously as the mechanical conditions for shear band formation, and twinning is an important mode of deformation. Both experimental and calculation show that the materials within the bands underwent a superhigh strain rate (9×105 s-1) deformation, which is two magnitudes of that of average strain rate required for shear band formation; the dislocations inthe bands can be constricted and developed into cell structures; the phase transformation from α to α2 within the bands was observed, and the transformation products (α2) had a certain crystallographic orientation relationship with their parent; the equiaxed grains with an average size of 10μm in diameter observed within the bands are proposed to be the results of recrystallization.

  7. Deformation quantization of principal bundles

    CERN Document Server

    Aschieri, Paolo

    2016-01-01

    We outline how Drinfeld twist deformation techniques can be applied to the deformation quantization of principal bundles into noncommutative principal bundles, and more in general to the deformation of Hopf-Galois extensions. First we twist deform the structure group in a quantum group, and this leads to a deformation of the fibers of the principal bundle. Next we twist deform a subgroup of the group of authomorphisms of the principal bundle, and this leads to a noncommutative base space. Considering both deformations we obtain noncommutative principal bundles with noncommutative fiber and base space as well.

  8. Mechanism of Difference of Deformation of High-Steep Slops Between Shiplift and Shiplock%论升船机与永久船闸陡高边坡变形差异的机理

    Institute of Scientific and Technical Information of China (English)

    刘国霖

    2001-01-01

    The result of difference of deformation stability of high-steepslops between the shiplift and shiplock at the Three Gorges Project is described.Their deformation stability were determined by the releas of accumulated elastic energy effect and the mechanical properties of the damaged rock mass.The different circumstance of deformations between the shiplift and the shiplock for the conditions of the slop borders and the shapes of the slop construction,are analyzed also.%岩石陡高边坡的变形稳定受控于断裂一损伤的岩体力学性质及累积弹性势能释放量的大小.依据三峡工程升船机与永久船闸岩体陡高边坡变形差异,讨论其与应力状态、累积弹性势能,以及工程优势面发育展布对岩体力学参数劣化影响的差异所形成的影响,对西部大开发所遇陡高边坡工程的研究,具有实际参考意义.

  9. Enhanced Hot Workability and Post-Hot Deformation Microstructure of the As-Cast Al-Zn-Cu-Mg Alloy Fabricated by Use of a High-Frequency Electromagnetic Casting with Electromagnetic Stirring

    Science.gov (United States)

    Park, S. Y.; Kim, W. J.

    2017-07-01

    The feasibility of producing an Al-Zn-Cu-Mg (7075) aluminum (Al) alloy using high-frequency electromagnetic casting (HFEMC) and electromagnetic stirring (EMS) was explored, and the microstructure, hot compressive deformation characteristics, and processing maps of the as-cast and homogenized EMS 7075 alloys were examined. The obtained results were compared with those of an alloy of the same composition, produced by direct chill casting (DCC). Application of the HFEMC/EMS technology resulted in grain refinement and suppression of dendritic growth. The grain size of the as-cast EMS 7075 alloy was smaller than that of the as-cast DCC 7075 alloy by more than half. This grain-size reduction increased the strain rate sensitivity and decreased the flow stress. The grain refinement also resulted in enhanced hot workability. Hot workability of the EMS 7075 alloy, however, considerably deteriorated after homogenization treatment. This resulted from the disappearance of the solute-segregated phases that play a role of accelerating dynamic recovery and continuous dynamic recrystallization during compressive deformation and the occurrence of considerable grain coarsening during homogenization treatment. The as-cast EMS 7075 alloy also showed a higher quality of post-hot working microstructure (after T6 heat treatment) compared to the homogenized EMS 7075 alloy. This resulted because the segregated phases in the as-cast microstructure served as the nucleation sites for new grains during static recrystallization by having created localized regions of high dislocation density around them during compressive deformation, especially at high strain rates. The current study showing that the as-cast EMS microstructure can yield a high hot workability as well as a high quality of post-hot working microstructure encourages the direct use of as-cast EMS 7075 alloy billets as feedstock for hot extrusion or forging.

  10. 海洋石油平台用E40钢板的高温变形行为%High Temperature Deformation Behavior for E40 Steel Plate Used for Offshore Platform

    Institute of Scientific and Technical Information of China (English)

    狄国标; 刘美艳; 麻庆申; 司良英; 刘振宇

    2013-01-01

    在MMS-200型热模拟试验机上通过单道次压缩试验研究了海洋平台用E40钢板的高温变形行为及动态再结晶行为;确定了该钢理想的加热温度.结果表明:随着变形温度的升高,该钢的动态再结晶临界切应力呈减小的趋势;动态再结晶的开始温度在900~950℃范围内;850℃时真应力-真应变曲线下降的主要原因是应变诱导铁素体相变;900℃以上时真应力-真应变曲线的下降是动态再结晶所致;其理想的变形加热温度为1 200℃.%High temperature deformation behavior and dynamic recrystalization behavior of an E40 steel plate used for offshore platform were studied by single-pass compressive testing on MMS-200 hot simulation tester. A perfect austenization temperature for the tested steel was determined. The results show that critical shear stree for dynamic recrystalization decreased with the increase of deformation temperature. The start temperature for dynamic recrystalization varied in the range of 900-950℃. The true stress-true strain curve declined at 850℃, which could be explained by strain-induced ferrite transformation, and when deformation temperature was above 900 ℃,dynamic recrystalization led to true stress-true strain curve declining. Ideal deformation temperature of the steel was 1 200℃.

  11. Deformation Crossover: from nano to meso scale

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Sheng [ORNL; Stoica, Alexandru Dan [ORNL; Wang, Xun-Li [ORNL; Liu, Chain T [ORNL; Horton Jr, Joe A [ORNL; Brown, Donald [Los Alamos National Laboratory (LANL); Clausen, B [Los Alamos National Laboratory (LANL); Liaw, Peter K [University of Tennessee, Knoxville (UTK)

    2009-01-01

    By investigating intergranular strains using in-situ high-energy x-ray and neutron diffraction, we demonstrate significantly different deformation behavior from previously observed in nanocrystalline and ultrafine-grained Ni. Little intergranular strain or texture change was found in nanocrystalline Ni indicating a grain boundary mediated deformation mechanism. A remarkable intergranular strain build-up was observed in ultrafine-grained Ni, which was attributed to dislocation activities, but the unusual angular dependence of intergranular strains gave evidence of stress relaxation by deformation twinning, as confirmed by TEM observations. From the intergranular strain evolution and the texture change, clear evidence of deformation crossovers is presented in Ni with grain sizes from nano to meso scale.

  12. Theoretical and experimental study of high strain, high strain rate materials viscoplastic behaviour. Application to Mars 190 steel and tantalum; Etude theorique et experimentale du comportement viscoplastique des materiaux aux grandes deformations et grandes vitesses de deformations. Application a l'acier mars 190 et au tantale

    Energy Technology Data Exchange (ETDEWEB)

    Juanicotena, A

    1998-07-01

    This work enters in the general framework of the study and modelling of metallic materials viscoplastic behaviour in the area of high strain and high strain rate, from 10{sup 4} to 10{sup 5} s{sup -1}. We define a methodology allowing to describe the behaviour of armor steel Mars 190 and tantalum in the initial area. In a first time, the study of visco-plasticity physical mechanisms shows the necessity to take into account some fundamental processes of the plastic deformation. Then, the examination of various constitutive relations allows to select the Preston-Tonks-Wallace model, that notably reproduce the physical phenomenon of the flow stress saturation. In a second part, a mechanical characterization integrating loading direction, strain rate and temperature effects is conducted on the two materials. Moreover, these experimental results allow to calculate associated constants to Preston-Tonks-Wallace, Zerilli-Armstrong and Johnson-Cook models for each material. In a third time, in order to evaluate and to validate these constitutive laws, we conceive and develop an experimental device open to reach the area of study: the expanding spherical shell test. It concerns to impose a free radial expanding to a thin spherical shell by means a shock wave generated by an explosive. By the radial expanding velocity measure, we can determine stress, strain rate and strain applied on the spherical shell at each time. In a four and last part, we evaluate constitutive models out of their optimization area's. This validation is undertaken by comparisons 'experimental results/calculations' with the help of global experiences like expanding spherical shell test and Taylor test. (author)

  13. Pollybeak Deformity in Middle Eastern Rhinoplasty: Prevention and Treatment.

    Science.gov (United States)

    Hussein, Wael K A; Foda, Hossam M T

    2016-08-01

    The pollybeak deformity is one of the commonest causes of revision rhinoplasty. The Middle Eastern nose has certain criteria that predispose to the development of pollybeak deformity. The aim of this study is to detect the factors contributing to the development of pollybeak deformity in the Middle Eastern nose and methods used to prevent as well as to treat such deformity. Out of the 1,160 revision patients included in this study, 720 (62%) patients had a pollybeak deformity. The commonest contributing factors included underprojected tip with poor support in 490 (68%) patients, excessive supratip scarring in 259 (36%) patients, overresected bony dorsum in 202 (28%) patients, and high anterior septal angle in 173 (24%) patients. The methods used by the authors to treat the pollybeak deformity are described, along with the local steroid injection protocol used to guard against the recurrence of pollybeak deformity. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

  14. Deformable Simplicial Complexes

    DEFF Research Database (Denmark)

    Misztal, Marek Krzysztof

    In this dissertation we present a novel method for deformable interface tracking in 2D and 3D|deformable simplicial complexes (DSC). Deformable interfaces are used in several applications, such as fluid simulation, image analysis, reconstruction or structural optimization. In the DSC method......, the interface (curve in 2D; surface in 3D) is represented explicitly as a piecewise linear curve or surface. However, the domain is also subject to discretization: triangulation in 2D; tetrahedralization in 3D. This way, the interface can be alternatively represented as a set of edges/triangles separating...... demonstrate those strengths in several applications. In particular, a novel, DSC-based fluid dynamics solver has been developed during the PhD project. A special feature of this solver is that due to the fact that DSC maintains an explicit interface representation, surface tension is more easily dealt with...

  15. Post-laminectomy deformities

    Directory of Open Access Journals (Sweden)

    Fabiano Stumpf Lutz

    2014-12-01

    Full Text Available Objective: To present the deformities and evaluate the results of their treatment. Methods: Retrospective study of patients with deformity following surgical access to the spinal canal. Fifteen patients who met the inclusion criteria were included. Patients without complete data in medical records were excluded. Results: Fourteen patients underwent surgical treatment and one patient received conservative treatment with vest type TLSO. The average angle of kyphosis correction was 87° preoperatively to 38° postoperatively, while the associated scoliosis correction was 69° preoperatively to 23° postoperatively. Conclusions: The prevention of deformity should be emphasized to avoid laminectomy alone, while laminoplasty should be the procedure of choice for canal access in surgeries where there is no need for resection of the posterior elements.

  16. Deformation of C isotopes

    CERN Document Server

    Kanada-Enyo, Y

    2004-01-01

    Systematic analysis of the deformations of proton and neutron densities in even-even C isotopes was done based on the method of antisymmetrized molecular dynamics. The $E2$ transition strength was discussed in relation to the deformation. We analyze the $B(E2;2^+_1\\to 0^+_1)$ in $^{16}$C, which has been recently measured to be abnormally small. The results suggest the difference of the deformations between proton and neutron densities in the neutron-rich C isotopes. It was found that stable proton structure in C isotopes plays an important role in the enhancement the neutron skin structure as well as in the systematics of $B(E2)$ in the neutron-rich C.

  17. Deformation in nanocrystalline metals

    Directory of Open Access Journals (Sweden)

    Helena Van Swygenhoven

    2006-05-01

    Full Text Available It is now possible to synthesize polycrystalline metals made up of grains that average less than 100 nm in size. Such nanocrystalline metals contain a significant volume fraction of interfacial regions separated by nearly perfect crystals. The small sizes involved limit the conventional operation of dislocation sources and thus a fundamental question arises: how do these materials deform plastically? We review the current views on deformation mechanisms in nanocrystalline, face-centered cubic metals based on insights gained by atomistic computer simulations. These insights are discussed with reference to recent striking experimental observations that can be compared with predictions made by the simulations.

  18. Heat treatment deformations

    Energy Technology Data Exchange (ETDEWEB)

    Bavaro, A. (Soliveri SpA, Caravaggio (Italy))

    1990-02-01

    Types and causes of heat treatement derived isotropic and anisotropic dilatancies in ferrous materials are reviewed. The concepts are developed in such a way as to allow extension to all materials exhibiting martensitic tempering behaviour. This paper intends to illustrate the basic processes of dimensional variations undergone by the materials under heat treatments. The parametric analysis includes an analysis of the interactions amongst the parameters themselves. The relative importance of each parameter is assessed in order to determine methods to attenuate deformation action. Simplified examples are offered to provide technicians explanations as to why specific deformations occur and indications on improved materials working techniques.

  19. [A modified retroperitoneal approach to the kidney in patients with a highly deformed thorax: obtaining a wide operative field through subperiosteal resection of the 10th, 11th and 12th ribs].

    Science.gov (United States)

    Satoh, Yuji; Kanou, Takehiro; Takagi, Norito; Tokuda, Yuji; Uozumi, Jiro; Masaki, Zenjiro

    2005-07-01

    We herein report a technique which facilitates a retroperitoneal approach to the kidney in cases of highly deformed thorax due to kyphoscoliosis. The operation consists of a lumbar oblique incision with removal of the 11th rib, combined with the additional removal of the 12th and 10th ribs. Resection of the upper two ribs was performed subperiosteally, leaving the periosteum of the deep side untouched. However, the deep side periosteum of the 12th rib was incised caudal from the pleural margin in order to facilitate exposure of the diaphragm. The retroperitoneal space was entered through the tip of the 11th rib bed. The diaphragm was incised dorso-medially at a level 1 cm caudal from the lower margin of the pleura, to an extent necessary to enable the pleura together with the cranial diaphragm to be manoeuvred in an upward direction. Two cases with renal tuberculosis associated with high-grade kyphosis and one case with staghorn calculi accompanied with lordosis were operated on utilizing this technique. In the former two cases, the thoracic cage was in direct contact with the iliac bone and there was practically no space between the rib border and the iliac crest. This was also true of the third case, but the grade of deformity was not as extensive as in the former two cases. Removal of the 10th, 11th and 12th ribs could be achieved without injuring the pleura and a satisfactorily large operating field could thus be developed which enabled a simple nephrectomy to be performed without difficulty. The characteristic feature of the described approach is that resection of the 10th and 11th ribs is simply to facilitate manoevr