WorldWideScience

Sample records for high-purity raw materials

  1. High purity materials as targets for radioisotope production: Needs ...

    Unknown

    lity of high purity target materials, natural or enriched, are crucial for any successful radioisotope pro- gramme. Selection ... and blockages detection in buried pipelines are rendered ..... from reputed international suppliers with analysis report.

  2. Development of high purity niobium material for superconducting cavities

    Umezawa, Hiroaki; Takeuchi, Koichi; Sakita, Kohei; Suzuki, Takafusa; Saito, Kenji; Noguchi, Shuichi.

    1993-01-01

    For the superconducting niobium cavities, issues of thermal quench and field emission have to be solved to achieve a high field gradient (>25MV/m) for TESLA (TeV Energy Superconducting Linear Accelerator). In order to overcome the quench, upgrading of thermal conductivity of niobium material at the low temperature is very important. On the reduction of the field emission not only dust particles but also defect, impurity and inhomogeneity should be considered. Therefore development of high purity niobium material is very important to solve these issues. This paper describes the our latest R and D for high purity niobium material. (author)

  3. High purity in steels as a criterion for materials development

    Jacobi, H.

    1995-01-01

    This summarizing report discusses the materials and application prospects for higher purity in steels, which will make possible further advances in materials behaviour and workability. Improvements in purity and homogeneity permit in particular more rational production of thin foils and wire, one-piece shaping of complicated bodywork components and the drawing, wall-ironing and flanging of two-piece beverage cans. Welded designs in plant and mechanical engineering can be fabricated with less effort and less weight. Difficult component geometries and shaping processes can be more easily mastered. Steels with optimized fracture toughness can be exposed to more extreme loads at even lower temperatures: applications worthy of mention include offshore engineering and large-diameter linepipes for use in arctic regions and at great underwater depths. Liquefied-gas transport vessels can be made more resistant to brittle rupture. The bending fatigue strength and service-life of valve-spring and rolling-bearing steels can be significantly increased. High-purity surfaces on piston rods and cylinders guarantee reliability in hydraulic systems, and high-purity calendering rolls permit defect-free embossing of paper surfaces. (orig.)

  4. The European Expression Of Interest For High Purity U-233 Materials

    Giaquinto, Joseph M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Younkin, James R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-04-01

    The purpose of this letter report is to document the response for an Expression of Interest (EOI) sent to the European Safeguards and research and development (R&D) scientific communities for the distribution of small amounts of high purity 233U materials for use in safeguards, nonproliferation, and basic R&D in the nuclear disciplines. The intent for the EOI was to gauge the level of international interest for these materials from government and research institutions with programmatic missions in the nuclear security or nuclear R&D arena. The information contained herein is intended to provide information to assist key decision makers in DOE as to the ultimate disposition path for the high purity materials currently being recovered at Oak Ridge National Laboratory (ORNL) and only those items for which there is no United States (U.S.) sponsor identified.

  5. High-Purity Semiconducting Single-Walled Carbon Nanotubes: A Key Enabling Material in Emerging Electronics.

    Lefebvre, Jacques; Ding, Jianfu; Li, Zhao; Finnie, Paul; Lopinski, Gregory; Malenfant, Patrick R L

    2017-10-17

    Semiconducting single-walled carbon nanotubes (sc-SWCNTs) are emerging as a promising material for high-performance, high-density devices as well as low-cost, large-area macroelectronics produced via additive manufacturing methods such as roll-to-roll printing. Proof-of-concept demonstrations have indicated the potential of sc-SWCNTs for digital electronics, radiofrequency circuits, radiation hard memory, improved sensors, and flexible, stretchable, conformable electronics. Advances toward commercial applications bring numerous opportunities in SWCNT materials development and characterization as well as fabrication processes and printing technologies. Commercialization in electronics will require large quantities of sc-SWCNTs, and the challenge for materials science is the development of scalable synthesis, purification, and enrichment methods. While a few synthesis routes have shown promising results in making near-monochiral SWCNTs, gram quantities are available only for small-diameter sc-SWCNTs, which underperform in transistors. Most synthesis routes yield mixtures of SWCNTs, typically 30% metallic and 70% semiconducting, necessitating the extraction of sc-SWCNTs from their metallic counterparts in high purity using scalable postsynthetic methods. Numerous routes to obtain high-purity sc-SWCNTs from raw soot have been developed, including density-gradient ultracentrifugation, chromatography, aqueous two-phase extraction, and selective DNA or polymer wrapping. By these methods (termed sorting or enrichment), >99% sc-SWCNT content can be achieved. Currently, all of these approaches have drawbacks and limitations with respect to electronics applications, such as excessive dilution, expensive consumables, and high ionic impurity content. Excess amount of dispersant is a common challenge that hinders direct inclusion of sc-SWCNTs into electronic devices. At present, conjugated polymer extraction may represent the most practical route to sc-SWCNTs. By the use of

  6. Trace elements in high purity materials for advanced technology: contribution of neutron activation analysis and radioanalytical technique

    Gallorini, M.; Pietra, R.; Sabbioni, E.

    1991-01-01

    Neutron activation analysis and radioanalytical techniques have been employed to investigate problems related to trace elements and high purity technology materials. Applications of these techniques are overviewed: semiconductor technology as in the case of As and In ion implantation in high purity silicon; problems related to trace elements impurities in thermometric measurements; coating materials to prevent trace elements contamination in biological sampling and metals release from human prostheses. (author) 8 refs.; 2 figs.; 8 tabs

  7. Recycling of high purity selenium from CIGS solar cell waste materials

    Gustafsson, Anna M.K., E-mail: anna.gustafsson@chalmers.se; Foreman, Mark R.StJ.; Ekberg, Christian

    2014-10-15

    Highlights: • A new method for recycling of selenium from CIGS solar cell materials is presented. • Separation of selenium as selenium dioxide after heating in oxygen atmosphere. • Complete selenium separation after oxidation of <63 μm particles at 800 °C for 1 h. • After reduction of selenium dioxide the selenium purity was higher than 99.999 wt%. - Abstract: Copper indium gallium diselenide (CIGS) is a promising material in thin film solar cell production. To make CIGS solar cells more competitive, both economically and environmentally, in comparison to other energy sources, methods for recycling are needed. In addition to the generally high price of the material, significant amounts of the metals are lost in the manufacturing process. The feasibility of recycling selenium from CIGS through oxidation at elevated temperatures was therefore examined. During oxidation gaseous selenium dioxide was formed and could be separated from the other elements, which remained in solid state. Upon cooling, the selenium dioxide sublimes and can be collected as crystals. After oxidation for 1 h at 800 °C all of the selenium was separated from the CIGS material. Two different reduction methods for reduction of the selenium dioxide to selenium were tested. In the first reduction method an organic molecule was used as the reducing agent in a Riley reaction. In the second reduction method sulphur dioxide gas was used. Both methods resulted in high purity selenium. This proves that the studied selenium separation method could be the first step in a recycling process aimed at the complete separation and recovery of high purity elements from CIGS.

  8. Computers in the investigation of the impurity content of high-purity materials

    Makarov, Yu.B.; Yan'kov, S.V.

    1987-01-01

    The efficiency of the concept of data banks for the accumulation and processing of information is now generally acknowledged. In scientific investigations not only bibliographic but also factual data banks are becoming more and more prevalent. In this article, the authors consider the possibilities of providing a data bank on high-purity materials for the study of impurity contents. Also in this paper, the authors distinguish the following groups of problems that arise in the study of impurity composition and presents examples of their proposed solutions to these problems: the analysis of error and the determination of the most probably value of impurity concentration; the estimation of average properties of impurity composition with respect to groups of impurities and samples, and the forecast of the complete impurity composition

  9. Photoluminescence measurement of polycrystalline CdTe made of high purity source material

    Hempel, Hannes; Kraft, Christian; Heisler, Christoph; Geburt, Sebastian; Ronning, Carsten; Wesch, Werner [Institute of Solid State Physics, Friedrich Schiller Universitaet Jena, Helmholtzweg 3, 07743 Jena (Germany)

    2012-07-01

    CdTe is a common material for thin film solar cells. However, the mainly used CdTe source material is known to contain a high number of intrinsic defects and impurities. In this work we investigate the defect structure of high purity CdTe by means of Photoluminescence, which is a common method to detect the energy levels of defects in the band gap of semiconductors. We used a 633 nm HeNe-Laser at sample temperatures of 8 K. The examined samples were processed in a new vacuum system based on the PVD method. They yield significantly different spectra on as-grown samples compared to those measured on samples which are grown by the standard process, since the double peak at 1.55 eV was hardly detectable and the A-center correlated transition vanished. Instead a peak at 1.50 eV with pronounced phonon coupling was observed. The 1.50 eV peak is known from other measurements but has not been characterized so far. The intention of this work is to characterize this new feature and the influence of post deposition treatments of the CdTe layers on the PL spectra.

  10. Raman and photoelectron spectroscopic investigation of high-purity niobium materials: Oxides, hydrides, and hydrocarbons

    Singh, Nageshwar; Deo, M. N.; Nand, Mangla; Jha, S. N.; Roy, S. B.

    2016-09-01

    We present investigations of the presence of oxides, hydrides, and hydrocarbons in high-purity (residual resistivity ratio, ˜300) niobium (Nb) materials used in fabrication of superconducting radio frequency (SRF) cavities for particle accelerators. Raman spectroscopy of Nb materials (as-received from the vendor as well as after surface chemical- and thermal processing) revealed numerous peaks, which evidently show the presence of oxides (550 cm-1), hydrides (1277 and 1385 cm-1: ˜80 K temperature), and groups of hydrocarbons (1096, 2330, 2710, 2830, 2868, and 3080 cm-1). The present work provides direct spectroscopic evidence of hydrides in the electropolished Nb materials typically used in SRF cavities. Raman spectroscopy thus can provide vital information about the near-surface chemical species in niobium materials and will help in identifying the cause for the performance degradation of SRF cavities. Furthermore, photoelectron spectroscopy was performed on the Nb samples to complement the Raman spectroscopy study. This study reveals the presence of C and O in the Nb samples. Core level spectra of Nb (doublet 3d5/2 and 3d3/2) show peaks near 206.6 and 209.4 eV, which can be attributed to the Nb5+ oxidation state. The core level spectra of C 1 s of the samples are dominated by graphitic carbon (binding energy, 284.6 eV), while the spectra of O 1 s are asymmetrically peaked near binding energy of ˜529 eV, and that indicates the presence of metal-oxide Nb2O5. The valence-band spectra of the Nb samples are dominated by a broad peak similar to O 2p states, but after sputtering (for 10 min) a peak appears at ˜1 eV, which is a feature of the elemental Nb atom.

  11. Raw material versus processing

    Berg, E.A.T.

    1989-01-01

    Some brazilian aspects related with the obtainment of raw materials for advanced ceramic products are described. The necessity of import raw materials by the advanced ceramic industries is mentioned, generating dangerous depedence for the country. The brazilian mineral reserves for using in raw materials of advanced ceramic are also cited. (C.G.C.) [pt

  12. Setting up of Nuclide GRAF-3S spark source mass spectrometer for the analysis of high purity materials

    Mahalingam, T.R.; Murugaiyan, P.; Soni, K.S.; Venkateswarlu, Ch.

    1975-01-01

    A spark source mass spectrometer model GRAF-35 manufactured by the Nuclide Corporation, U.S.A., was set up for analysis of nuclear-grade and high purity materials. The main difficulty with its successful operation was to achieve and maintain the required level of vacuum i.e. less than 2X10 -8 torr in the magnetic analyser region. With 100 1/s ion pump, the required vacuum could be achieved, but the spectrometer required periodical baking which minimises the life of the instrument. The pumping system was replaced by Ultek Boostivac pump - a combination of ion pump (150 1/s) and a titanium sublimation pump (1000 1/sec speed for condensable vapours) which eliminated baking as the necessary level of vacuum could be easily achieved whenever required. Results of the analysis of zone-refined indium and uranium for trace impurities are given. (M.G.B.)

  13. Preparation of high-purity cerium nitrate

    Avila, Daniela Moraes; Silva Queiroz, Carlos Alberto da; Santos Mucillo, Eliana Navarro dos

    1995-01-01

    The preparation of high-purity cerium nitrate has been carried out Cerium oxide has been prepared by fractioned precipitation and ionic exchange techniques, using a concentrate with approximately 85% of cerium oxide from NUCLEMON as raw material. Five sequential ion-exchange columns with a retention capacity of 170 g each have been used. The ethylenediamine-tetraacetic acid (EDTA) was used as eluent. The cerium content has been determined by gravimetry and iodometry techniques. The resulting cerium oxide has a purity > 99%. This material was transformed in cerium nitrate to be used as precursor for the preparation of Zirconia-ceria ceramics by the coprecipitation technique. (author)

  14. Raw material uranium

    Arnold, O.

    1975-01-01

    In this paper some aspects are being considered, in as far as they can contribute to a better understanding of uranium as a raw material and an energy carrier, and as they can indicate the possible ways and means open to the German Federal Republic for securing this highly desirable raw material, without becoming even more dependent on the economic and political views of the producing countries, than it is the case in respect of oil. (orig.) [de

  15. Strategic raw materials. Risk management

    Bertau, Martin; Matschullat, Joerg; Kausch, Peter

    2014-01-01

    This volume is divided into four chapters: (1) Raw material management, (2) Primary raw materials, (3) Secondary raw materials and recycling, (4). Processing and products. The topics for the chapter ''Raw material management'' are: Substitution of raw materials - framework conditions and implementation; Thales: Strategic raw materials; Time for cooperation between the EU and China in raw materials policy; Availability of elements for the semiconductor industry; Market price risks of raw material-intensive companies - identification and management. The topics on the second item ''Primary raw materials'' are: The supply of economic-critical raw materials - A search and analysis for causes; Lithium extraction from primary raw materials - state and perspectives; The global market of rare earths - A balancing act; Rare earth deposits in Namibia; New technologies in exploration and discovery - Focus on activities in Europe. The third chapter, ''Secondary Raw Materials and Recycling'', covered the topics: Technology metals - Systemic Requirements along the recycling chain; Integrated re-use of high-tech and greentech wastes; From the sewage sludge ash to the phosphorus fertilizer RecoPhos P38 in the stress field of waste, fertilizer and soil protection. In chapter 4. ''Processing and products'' are the topics: Treatment and processing of rare earth metals; Processing of mineral resources - opportunities and challenges; Consequences of modern germanium chemistry; Strategic resources - Risk management. A review and outlook with a pinch of fantasy.. [de

  16. Characterization of silica quartz as raw material in photovoltaic applications

    Boussaa, S. Anas, E-mail: sabiha.anas@gmail.com; Kheloufi, A.; Kefaifi, A.; Kerkar, F. [Division croissance cristalline et procédés métallurgiques CCPM Centre de recherche en technologie des semi-conducteurs pour l’énergétique (C.R.T.S.E) 02 Bd Frantz Fanon BP. 140 Alger 7 merveilles, Alger 16200 (Algeria); Zaourar, N. Boutarek [Laboratoire des technologies des matériaux, USTHB, B.P. 32 El Alia, Bab Ezzouar, Alger, Algérie 16111 (Algeria)

    2016-07-25

    Raw materials are essential for the functioning of modern societies, and access to these raw materials is vital to the world economy. Sustainable development, both globally level, raises important new challenges associated with access and efficient use of raw materials. High purity quartz, is consider as a critical raw material and it is a rare commodity that only forms under geological conditions where a narrow set of chemical and physical parameters is fulfilled. When identified and following special beneficiation techniques, high purity quartz obtains very attractive prices and is applied in high technology sectors that currently are under rapid expansion such as photovoltaic solar cells, silicon metal - oxide wafers in the semiconductor industry and long distance optical fibers that are used in communication networks. Crystalline silicon remains the principal material for photovoltaic technology. Metallurgical silicon is produced industrially by the reduction of silica with carbon in an electric arc furnace at temperatures higher than 2000 °C in the hottest parts, by a reaction that can be written ideally as: SiO{sub 2} + 2C = Si + 2CO. The aim of this study has been to test experimental methods for investigating the various physical and chemical proprieties of Hoggar quartz with different techniques: X Ray Fluorescence, infra-red spectroscopy, Scanning Electron Microscopy, Optic Microscopy, Carbon Analyzer and Vickers Hardness. The results show finally that the quartz has got good result in purity but need enrichment for the photovoltaic application.

  17. Possible influence of surface oxides on the optical response of high-purity niobium material used in the fabrication of superconducting radio frequency cavity

    Singh, Nageshwar; Deo, M. N.; Roy, S. B.

    2016-09-01

    We have investigated the possible influence of surface oxides on the optical properties of a high-purity niobium (Nb) material for fabrication of superconducting radio frequency (SCRF) cavities. Various peaks in the infrared region were identified using Fourier transform infrared and Raman spectroscopy. Optical response functions such as complex refractive index, dielectric and conductivity of niobium were compared with the existing results on oxides free Nb and Cu. It was observed that the presence of a mixture of niobium-oxides, and probably near other surface impurities, appreciably influence the conducting properties of the material causing deviation from the typical metallic characteristics. In this way, the key result of this work is the observation, identification of vibrational modes of some of surface complexes and study of its influences on the optical responses of materials. This method of spectroscopic investigation will help in understanding the origin of degradation of performance of SCRF cavities.

  18. Possible influence of surface oxides on the optical response of high-purity niobium material used in the fabrication of superconducting radio frequency cavity

    Singh, Nageshwar; Deo, M.N.; Roy, S.B.

    2016-01-01

    We have investigated the possible influence of surface oxides on the optical properties of a high-purity niobium (Nb) material for fabrication of superconducting radio frequency (SCRF) cavities. Various peaks in the infrared region were identified using Fourier transform infrared and Raman spectroscopy. Optical response functions such as complex refractive index, dielectric and conductivity of niobium were compared with the existing results on oxides free Nb and Cu. It was observed that the presence of a mixture of niobium-oxides, and probably near other surface impurities, appreciably influence the conducting properties of the material causing deviation from the typical metallic characteristics. In this way, the key result of this work is the observation, identification of vibrational modes of some of surface complexes and study of its influences on the optical responses of materials. This method of spectroscopic investigation will help in understanding the origin of degradation of performance of SCRF cavities.

  19. Possible influence of surface oxides on the optical response of high-purity niobium material used in the fabrication of superconducting radio frequency cavity

    Singh, Nageshwar [Magnetic and Superconducting Materials Section, Raja Ramanna Centre for Advanced Technology, Indore 452013, M.P. (India); Deo, M.N. [High Pressure & Synchrotron Radiation Physics Division, BARC, Mumbai 400085 (India); Roy, S.B. [Magnetic and Superconducting Materials Section, Raja Ramanna Centre for Advanced Technology, Indore 452013, M.P. (India)

    2016-09-11

    We have investigated the possible influence of surface oxides on the optical properties of a high-purity niobium (Nb) material for fabrication of superconducting radio frequency (SCRF) cavities. Various peaks in the infrared region were identified using Fourier transform infrared and Raman spectroscopy. Optical response functions such as complex refractive index, dielectric and conductivity of niobium were compared with the existing results on oxides free Nb and Cu. It was observed that the presence of a mixture of niobium-oxides, and probably near other surface impurities, appreciably influence the conducting properties of the material causing deviation from the typical metallic characteristics. In this way, the key result of this work is the observation, identification of vibrational modes of some of surface complexes and study of its influences on the optical responses of materials. This method of spectroscopic investigation will help in understanding the origin of degradation of performance of SCRF cavities.

  20. Raw materials for aluminium production

    Galushkin, N.V.

    1995-01-01

    This chapter of monograph is devoted to to raw materials which used in aluminium production. Therefore, the using of alumina, and fluoride salts in aluminium production was considered. The physical properties of alumina were studied.

  1. Raw Materials Market of China

    Dmitry Alexandrovich Izotov

    2013-12-01

    Full Text Available Deficit of raw materials is becoming an important concern for the Chinese economy as it continues to grow. This deficit is amended with imports, which – in their own turn – are limited by the high level of global prices. The build-up issue of raw materials imports is going to solve by the measures of monetary policy (RMB’s revaluation against the USD. Analysis of China’s market of raw materials reveals that the largest increase in the physical volume of imports is concentrated in crude oil, LNG, iron ore and coal. As for Russia, its supplies and share in total Chinese imports of raw materials tend to increase. Author employs regression equations based on international statistics data to show that RMB’s revaluation, ceteris paribus, increases physical volumes of raw materials imports. However, the main factor of coal and LNG imports growth is energy consumption by Chinese heavy industry; imports of oil products – producers’ prices; meanwhile imports of steel products tend to decrease with the growth of steel exports. RMB’s revaluation increases physical volumes of imports of low value added raw materials from Russia (coal, crude oil, iron ore

  2. Raw materials for advanced ceramics: rare earths separation processes

    Ricci, D.R.; Nobre, J.S.M.; Paschoal, J.O.A.

    1990-01-01

    The importance of obtaining purified rare earths oxidesis related, mainly to the increasing use of these compounds as raw materials for advanced ceramics. Processes of rare earths separation and purification are almost always based on the solvent extraction, fractional precipitation and ion exchange chromatography techniques, whose association depends on the initial concentrate and on the desired purity. This paper describes some steps of fractionation of didymium carbonate by using the solvent extraction and fractional precipitation techniques. The experimental conditions presented here have enable the production of lantanium, neodimium - praseodimium, samarium - gadolinium and ytrium concentrates, which constitute the intermediate fractions of the overall process to obtain high purity rare earths. (author) [pt

  3. Development of a certified reference material for composition of high-purity copper as a transfer standard within GET 176-2013

    Veniamin M. Zyskin

    2017-01-01

    Full Text Available Introduction. The paper gives information on the development of a certified reference material (CRM for composition of high-purity copper (Cu CRM UNIIM. The CRM is included as the transfer standard into the State primary standard of the mass (molar fraction and mass (molar concentration of the component in liquid and solid substances and materials based on coulometry GET 176-2013.Materials and methods. The CRM represents pieces of oxygen-free copper wire rod, brand KMB, produced according to GOST R 53803-2010, weighing from 0.5 to 1g. The CRM is packed in plastic vials with the capacity of 30 or 50 cm3. The certified characteristic of the CRM is copper mass fraction in copper wire rod, expressed in percentages. The certified value for copper mass fraction was established by the primary method of controlled-potential coulometry using the State primary standard GET 176-2013.Results. The permitted interval of the certified value for copper mass fraction in the CRM is from 99,950 % to 100,000 %. The relative expanded uncertainty (k=2 of the certified value for copper mass fraction does not exceed 0,030 %; the relative standard uncertainty due to inhomogeneity does not exceed 0.010 %; the relative standard uncertainty due to instability does not exceed 0.010 %. The shelf life of the developed CRM is 10 years provided that standard storage conditions are ensured.Discussion and conclusions. The developed CRM is included into the State register of type approved RMs under the number GSO 10800-2016. The CRM of high-purity copper (Cu CRM UNIIM as a transfer standard is intended for reproduction, storage and transfer of the copper mass fraction unit to other reference materials and chemical reagents by the method of comparison using a comparator and by conducting direct measurements. This CRM may also be used:– for verification of measuring instruments (MIs according to the state verification schedule described in GOST R 8.735.0-2014,– for calibration

  4. Topical papers on raw materials

    1978-01-01

    In the papers of this working group, the availability of uranium and the long-term supply situation for this raw material are discussed. A problem closely connected with uranium supply are the commercial contracts and their particularities. The points of view of the reporting countries of Great Britain, South Africa, Switzerland, Australia, Japan, and Korea are made clear

  5. Raw material uranium; Rohstoff Uran

    NONE

    2017-03-15

    Uranium is an important raw material in human life. Mostly using nuclear fission uranium is used in nuclear medicine, industry and research. The most important application is the generation of electricity in nuclear power plants. Due to the global availability the worldwide uranium supply is guaranties for a long time. The contribution covers the issues medicine, neutron research, energy generation, occurrence, mining, processing, recycling and disposal.

  6. Growth of high purity semiconductor epitaxial layers by liquid phase ...

    Unknown

    semiconductor materials in high purity form by liquid phase epitaxy (LPE) technique. Various possible sources of impurities in such ... reference to the growth of GaAs layers. The technique of growing very high purity layers ... the inner walls of the gas lines and (e) the containers for storing, handling and cleaning of the mate-.

  7. Production of high purity radiothallium

    Lebowitz, E.; Greene, M.W.

    1976-01-01

    The method of producing high-purity thallium-201 for use as a myocardial scanning agent comprises the steps of irradiating a thallium target with protons to give the reaction 203 Tl(p,3n) 201 Pb, separating in ion exchange columns the lead from the thallium isotopes, permitting the lead to decay, and then purifying the thallium solution and converting the thallium present to thallous form in which it can be used

  8. The Research about Preparation of High Purity Hexachlorodisilane

    Wan, Ye; Zhao, Xiong; Yan, Dazhou; Zhao, Yu; Guo, Shuhu; Wang, Lei; Yang, Dian

    2017-12-01

    This article demonstrated a technology for producing high purity hexachlorodisilane what is one raw material of Semiconductor industry, which using the method of combination adsorption with rectification, whose material was from polysilicon residues of polysilicon company. This technology could remove most high boiling points chloro-silicane impurities and metal impurities effectively. The purity of Si2Cl6 produced by this technology can be up to 99.9%, the content of metal impurities can be low at 4ppb, which can meet the requirement of industy using completely. The technology extends the routes of Si2Cl6 in localization, having the advantages of simple process, continuous operation, and large capacity and so on.

  9. Radioactivity in polluted cement and its raw materials

    Khan, K.; Aslam, M.; Orfi, S.D.

    1999-01-01

    Samples of portland cement manufactured in the North West frontier Province (NWFP) of Pakistan and its different raw materials have been investigated applying gamma-spectrometric techniques for natural gamma-emitting radionuclides. A high purity germanium detector (HPGE) was used for data acquisition. Average values of the total specific activity (in Bq.kg/sup -1/ ) due to all the three radionuclides (/sub 40/K, /sup 226/Ra and /sup 232/Th) were found to be 327.7+ - 168.2 for portland cement; 104.4 + - 21.1 for limestone; 193.2+ - 50.4 for gypsum; 890.4 + - 86.5 for state and 545.6+ - 56.6 for latrite. The average specific activities due to /sup 40/K in Portland cement and all the raw materials were found to be higher as compared to /sub 226/Ra and /sup 232/Th in the respective materials. It is concluded that such materials do not pose any health problem and are not a major source of radiation hazards. However, The data can be utilized in determining radioactivity associated with other building materials. (author)

  10. Preserving high-purity 233U

    Krichinsky, Alan; Giaquinto, Joe; Canaan, Doug

    2016-01-01

    The MARC X Conference hosted a workshop for the scientific community to communicate needs for high-purity 233 U and its by-products in order to preserve critical items otherwise slated for downblending and disposal. Currently, only small portions of the U.S. holdings of separated 233 U are being preserved. However, many additional kilograms of 233 U (>97 % pure) still are destined to be disposed, and it is unlikely that this material will ever be replaced due to a lack of operating production capability. Summaries of information conveyed at the workshop and feedback obtained from the scientific community are presented herein. (author)

  11. Qualification Methods of Al2O3 Injection Molding Raw Materials

    Egész, Á; Gömze, L A

    2015-01-01

    For producing ceramic arc tube parts (plugs), there are used two different major components for producing injection molding raw material (feedstock): high purity alumina powder as the main component, and an organic paraffin wax as a binder material. It is expressly important to know the material, physical and chemical properties of these components, since mainly these have effect on the homogenity of feedstock, and therefore on the quality of end product. In this research, both of the main components and the moldable raw material was investigated by visual, physical, and thermal methods. As most important and main statement, the researchers found that the dynamic viscosity of raw material depends more on the applied temperature, than on the deformation speed gradient.Applied analitycal methods were laser granulometry, sieve analysis, differential thermal analysis and rheology analysis. (paper)

  12. High-Purity Glasses Based on Arsenic Chalcogenides

    2001-06-01

    Chemical interaction of chalcogenides and some impurities (CS 2, TeO2 ) with the quartz glass at high temperature leads to the thin layers formation...UNCLASSIFIED Defense Technical Information Center Compilation Part Notice ADPO1 1523 TITLE: High-Purity Glasses Based on Arsenic Chalcogenides...Materials Vol. 3, No. 2, June 2001, p. 341 - 349 HIGH-PURITY GLASSES BASED ON ARSENIC CHALCOGENIDES M. F. Churbanov, I. V. Scripachev, G. E. Snopatin, V. S

  13. A combined arc-melting and tilt-casting furnace for the manufacture of high-purity bulk metallic glass materials.

    Soinila, E; Pihlajamäki, T; Bossuyt, S; Hänninen, H

    2011-07-01

    An arc-melting furnace which includes a tilt-casting facility was designed and built, for the purpose of producing bulk metallic glass specimens. Tilt-casting was chosen because reportedly, in combination with high-purity processing, it produces the best fatigue endurance in Zr-based bulk metallic glasses. Incorporating the alloying and casting facilities in a single piece of equipment reduces the amount of laboratory space and capital investment needed. Eliminating the sample transfer step from the production process also saves time and reduces sample contamination. This is important because the glass forming ability in many alloy systems, such as Zr-based glass-forming alloys, deteriorates rapidly with increasing oxygen content of the specimen. The challenge was to create a versatile instrument, in which high purity conditions can be maintained throughout the process, even when melting alloys with high affinity for oxygen. Therefore, the design provides a high-vacuum chamber to be filled with a low-oxygen inert atmosphere, and takes special care to keep the system hermetically sealed throughout the process. In particular, movements of the arc-melting electrode and sample manipulator arm are accommodated by deformable metal bellows, rather than sliding O-ring seals, and the whole furnace is tilted for tilt-casting. This performance of the furnace is demonstrated by alloying and casting Zr(55)Cu(30)Al(10)Ni(5) directly into rods up to ø 10 mm which are verified to be amorphous by x-ray diffraction and differential scanning calorimetry, and to exhibit locally ductile fracture at liquid nitrogen temperature.

  14. High purity neodymium acetate from mixed rare earth carbonates

    Queiroz, Carlos A. da Silva; Rocha, Soraya M. Rizzo da; Vasconcellos, Mari E. de; Lobo, Raquel M.; Seneda, Jose A.; Pedreira, Walter dos R.

    2011-01-01

    A simple and economical chemical process for obtaining high purity neodymium acetate is discussed. The raw material in the form rare earth carbonate is produced industrially from the chemical treatment of Brazilian monazite. Ion exchange chromatography technique with a strong cationic resin, proper to water treatment, and without the use of retention ions was used for the fractionating of the rare earth elements (REE). In this way, it was possible to obtain 99.9% pure Nd 2 O 3 in yields greater than or equal 80%, with the elution of the REE using ammonium salt of ethylenediaminetetraacetic acid (EDTA) solution in pH controlled. The complex of EDTA-neodymium was transformed into neodymium oxide, which was subsequently dissolved in acetic acid to obtain the neodymium acetates. Molecular absorption spectrophotometry was used to monitor the neodymium content during the process and sector field inductively coupled plasma mass spectrometry was used to certify the purity of the neodymium acetates. The typical neodymium acetates obtained contain the followings contaminants in μg g -1 : Sc(5.1); Y (0.9); La (1.0); Ce (6.1); Pr (34,4); Sm (12.8); Eu (1.1); Gd (15.4); Tb (29.3); Dy (5.2), Ho(7.4); Er (14.6); Tm (0.3); Yb (2.5); Lu (1.0). The high purity neodymium acetates obtained from this procedure have been applied, replacing the imported product, in research and development area on rare earth catalysts. (author)

  15. Raw materials policy: implications for Germany

    Gaertner, E

    1978-04-01

    The contribution characterizes the situation of the national mining industry in 1977, deals with international raw materials policies within the framework of the North-South dialogue and with the policies of the western industrial countries, points out the dangers of worldwide state-controlled raw materials policies and calls for a) the political risk of enterprise cooperation with developing countries to be covered and b) double taxation to be avoided. Finally, the problems of securing the Federal Republic of Germany's raw materials supplies on a long-term basis are portrayed.

  16. Preparation of high-purity cerium nitrate; Preparacao de nitrato de cerio de alta pureza

    Avila, Daniela Moraes; Silva Queiroz, Carlos Alberto da; Santos Mucillo, Eliana Navarro dos [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

    1995-12-31

    The preparation of high-purity cerium nitrate has been carried out Cerium oxide has been prepared by fractioned precipitation and ionic exchange techniques, using a concentrate with approximately 85% of cerium oxide from NUCLEMON as raw material. Five sequential ion-exchange columns with a retention capacity of 170 g each have been used. The ethylenediamine-tetraacetic acid (EDTA) was used as eluent. The cerium content has been determined by gravimetry and iodometry techniques. The resulting cerium oxide has a purity > 99%. This material was transformed in cerium nitrate to be used as precursor for the preparation of Zirconia-ceria ceramics by the coprecipitation technique. (author) 2 tabs.

  17. Study of Pellets and Lumps as Raw Materials in Silicon Production from Quartz and Silicon Carbide

    Dal Martello, E.; Tranell, G.; Gaal, S.; Raaness, O. S.; Tang, K.; Arnberg, L.

    2011-10-01

    The use of high-purity carbon and quartz raw materials reduces the need for comprehensive refining steps after the silicon has been produced carbothermically in the electric reduction furnace. The current work aims at comparing the reaction mechanisms and kinetics occurring in the inner part of the reduction furnace when pellets or lumpy charge is used, as well as the effect of the raw material mix. Laboratory-scale carbothermic reduction experiments have been carried out in an induction furnace. High-purity silicon carbide and two different high-purity hydrothermal quartzes were charged as raw materials at different molar ratios. The charge was in the form of lumps (size, 2-5 mm) or as powder (size, 10-20 μm), mixed and agglomerated as pellets (size, 1-3 mm) and reacted at 2273 K (2000 °C). The thermal properties of the quartzes were measured also by heating a small piece of quartz in CO atmosphere. The investigated quartzes have different reactivity in reducing atmosphere. The carbothermal reduction experiments show differences in the reacted charge between pellets and lumps as charge material. Solid-gas reactions take place from the inside of the pellets porosity, whereas reactions in lumps occur topochemically. Silicon in pellets is produced mainly in the rim zone. Larger volumes of silicon have been found when using lumpy charge. More SiO is produced when using pellets than for lumpy SiO2 for the same molar ratio and heating conditions. The two SiC polytypes used in the carbothermal reduction experiments as carbon reductants presented different reactivity.

  18. Quality quantification model of basic raw materials

    Š. Vilamová

    2016-07-01

    Full Text Available Basic raw materials belong to the key input sources in the production of pig iron. The properties of basic raw materials can be evaluated using a variety of criteria. The essential ones include the physical and chemical properties. Current competitive pressures, however, force the producers of iron more and more often to include cost and logistic criteria into the decision-making process. In this area, however, they are facing a problem of how to convert a variety of vastly different parameters into one evaluation indicator in order to compare the available raw materials. This article deals with the analysis of a model created to evaluate the basic raw materials, which was designed as part of the research.

  19. Annual report 1997. Energies and raw materials

    1997-01-01

    This report gives the important directions of French energy policy. Nuclear energy, electric power, natural gas, coal and petroleum products are reviewed. The situations and the forecasting for raw materials are also given. (N.C.)

  20. Aluminium reprocessing with local mineral raw material

    Mirsaidov, U.M.

    2002-01-01

    With the purpose of utilization of ice sediment, receiving from mud fields solutions and flotation tails and at using local aluminium and fluorine-containing raw material was elaborated fundamental technologic scheme presented in this chapter of book

  1. Batch extractive distillation for high purity methanol

    Zhang Weijiang; Ma Sisi

    2006-01-01

    In this paper, the application in chemical industry and microelectronic industry, market status and the present situation of production of high purity methanol at home and abroad were introduced firstly. Purification of industrial methanol for high purity methanol is feasible in china. Batch extractive distillation is the best separation technique for purification of industrial methanol. Dimethyl sulfoxide was better as an extractant. (authors)

  2. Plastic raw materials in Neolithic pottery production

    Alexander A. Bobrinsky

    2012-12-01

    Full Text Available The paper is dedicated to the investigation of various natural silts as the most ancient type of raw material used in pottery production. The authors describe the specific features of the composition of plain and mountain silts, and discover the same features in ancient ceramics from different regions in Russia. It can be concluded that silts were the earliest raw material used, a tradition that faded away during the evolution of pottery production.

  3. Recent developments in high purity niobium metal production at CBMM

    Abdo, Gustavo Giovanni Ribeiro; Sousa, Clovis Antonio de Faria; Guimarães, Rogério Contato; Ribas, Rogério Marques; Vieira, Alaércio Salvador Martins; Menezes, Andréia Duarte; Fridman, Daniel Pallos; Cruz, Edmundo Burgos

    2015-01-01

    CBMM is a global supplier of high quality niobium products including pure niobium, the focus of this paper. CBMM’s position has been consolidated over three decades of producing high purity niobium metal ingots. The company supplies, among other products, commercial and reactor grade niobium ingots. One of the main uses of CBMM’s ingots is for the manufacture of particle accelerators (superconducting radio frequency – SRF – cavities), where the purity and homogeneity of niobium metal is essentially important for good performance. CBMM constantly strives to improve process controls and product quality, and is currently implementing innovations in production, research and development to further improve ingot quality. The main aim is to reduce the content of interstitial elements, such as nitrogen (N), oxygen (O), carbon (C), and hydrogen (H), starting with the raw materials through the final step of ingot production. CBMM held the first trial to produce the world’s largest-diameter niobium ingot (as cast 535 mm). The results of this initial trial presented very low levels of interstitial impurities (N, O, C, H), allowing the achievement of residual resistivity ratio (RRR) values very close to 300 in a six-melt process in an electron beam furnace. These values were reached with 850 ppm of tantalum. SRF cavities will be produced with this material in order to study the effect of low impurities and high RRR on the Q factor and accelerating gradient

  4. Production of high purity granular metals: cadmium, zinc, lead

    Shcherban A. P.

    2017-04-01

    Full Text Available Cadmium, zinc and lead are constituent components of many semiconductor compounds. The obtained high purity distillates and ingots are large-size elements, which is not always convenient to use, and thus require additional grinding, which does not always allow maintaining the purity of the original materials. For the growth of semiconductor and scintillation single crystals it is advisable to use "friable" granular high-purity distillates, which can be processed without the risk of contamination. For example, the European low-background experiment LUCIFER required more than 20 kg of high-purity granulated zinc, which was agreed to be supplied by NSC KIPT. This task was then extended to cadmium and lead. Motivated by these tasks, the authors of this paper propose complex processes of deep refining of cadmium, zinc and lead by vacuum distillation. A device producing granules has been developed. The process of granulation of high-purity metals is explored. The purity of produced granules for cadmium and zinc is >99,9999, and >99,9995% for lead granules. To prevent oxidation of metal granules during exposition to air, chemical methods of surface passivation were used. Organic solvent based on dimethylformamide used as a coolant improves the resistance of granules to atmospheric corrosion during the granulation of high purity Cd, Zn and Pb.

  5. Ways for accurate analysis of high purity materials using the glow discharge mass spectrometry (GD-MS); Wege zur genauen Charakterisierung hochreiner Materialien mit der Glimmentladungs-Massenspektrometrie (GD-MS)

    Gusarova, Tamara

    2010-04-14

    The main aim of this work consists in the investigation, development and application of improved possibilities of accurate analysis of high purity materials using the solid sample technique of Glow Discharge Mass Spectrometry (GD-MS), as well as in the sensitivity enhancement of GD Optical Emission Spectrometry (GD-OES) by implicating the hollow cathode effect. The emphasis of the PhD thesis consists in the accurate quantification for GD-MS. As appropriate certified reference materials (CRMs) for calibration are lacking in most cases an accurate quantification especially for trace elements mass fractions at {mu}g kg{sup -1} level can often not be achieved. To overcome this problem and to expand the possibilities of modern GD-MS hereby, synthetic standards were applied for calibration of both high resolution GD-MS instruments ''VG 9000'' and ''Element GD''. The standards were prepared by doping of matrix powder with trace element standard solutions followed by drying and pressing the doped powder to compact pellets. With the quantification approach worked out and described here accurate analysis results with small uncertainties can be achieved for most elements of periodic table in almost every matrix composition. Furthermore direct traceability of the analytical results to the International System of Units (SI) is provided ensuring their higher metrological quality. Numerous additional systematic investigations concerning the preparation of the synthetic standards and their properties were carried out. The results of calibration of GD-MS instruments with synthetic standards for Co (Co-C), Cu, In, Fe and Zn matrices were checked by measuring CRMs. These results were also contrasted with those of other quantification approaches, as usually used in GD-MS routine. The results achieved with synthetic standards had the highest accuracy. The successful participation in the round robin test CCQM-P107 between international

  6. Ethanol is a strategic raw material

    Baras Josip K.

    2002-01-01

    Full Text Available The first part of this review article considers general data about ethanol as an industrial product, its qualities and uses. It is emphasized that, if produced from biomass as a renewable raw material, its perspectives as a chemical raw material and energent are brilliant. Starchy grains, such as corn, must be used as the main raw materials for ethanol production. The production of bioethanol by the enzyme-catalyzed conversion of starch followed by (yeast fermentation, distillation is the process of choice. If used as a motor fuel, anhydrous ethanol can be directly blended with gasoline or converted into an oxygenator such as ETBE. Finally, bioethanol production in Yugoslavia and the possibilities for its further development are discussed.

  7. PERSPECTIVE NONMETALLIC RAW MATERIALS AND THEIR UTILIZATION

    Havelka Jaroslav

    1997-10-01

    Full Text Available It is the existence of the domestic base of raw materials and stable or growing markets that are a precondition for the prospectiveness industrial minerals. Traditional and non-traditional prospective nonmetal-liferous raw materials can be distinguished. The main trends in new industrial applications of industrial minerals are being stated. In the Czech Republic, the following may be ranked among the traditional prospective nonme-talliferous raw materials: kaoline, refractory clays, ceramic and expandable clays, glass and foundry sands, li-mestones, building stones, gypsum, cast basalt, bentonite, diatomite, feldspars, graphite. Alkali rocks, industrial garnets, flaky mica, wollastonite and yet unmined staurolite, minerals of the sillimanite group and others belong to the non-traditional prospective industrial minerals.

  8. High purity samarium oxide from mixed rare earth carbonates

    Queiroz, Carlos A. da S.; Seneda, Jose A.; Vasconcellos, Mari E. de; Pedreira Filho, Walter dos R.

    2013-01-01

    A simple and economical chemical process for the production of highly pure samarium oxides is discussed. The raw material, which was used in the form of rare earth carbonates was produced industrially from the chemical treatment of Brazilian monazite. Ion exchange chromatography was performed using a strong cationic resin that is typically employed in water treatment processes to fractionate rare earth elements (REE) without the use of retention ions. Under these conditions, 99.9% pure Sm 2 O 3 was eluted using the ammonium salt of ethylenediaminetetraacetic acid (EDTA) at a controlled pH. The EDTA-samarium complex was separated from EDTA and then precipitated as oxalate and fired to samarium oxide. Molecular absorption spectrophotometry was used to monitor the samarium content during the proposed process, and sector field inductively coupled plasma mass spectrometry was used to certify the purity of the samarium oxide. Typical samarium oxide obtained from the proposed procedure contained the following contaminants in micrograms per gram: Sc (20.90); Y (11.80); La (8.4); Ce (4.3); Pr (2.5); Nd (5.1); Eu (94); Gd (114); Tb (3.6); Dy (2.5), Ho (2.3); Er (3.0); Tm (2.3); Yb (38,2); Lu (25.6). The high-purity samarium oxides produced in the present study can be used as an alternative to imported products in research and development applications. (author)

  9. Raw materials resources classification and characterisation for ...

    Raw materials resources classification and characterisation for ceramic tableware production in Nigeria. PSA Irabor. Abstract. No Abstract. Journal of Applied Science, Engineering and Technology Vol. 2(1) 2002: 48-52. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

  10. Extraction of protoactinium from silicaceous raw material

    Broda, E.

    1946-07-01

    This report was written by E. Broda and P.K. Wright at the Cavendish Laboratory (Cambridge) in March 1946 and is about the Extraction of protoactinium from a silicaceous raw material. In this report the isolation of Pa on Er carrier is described and it includes the experiment description and the discussion of the results. (nowak)

  11. Recovery of the secondary raw materials, recycling

    Chmielewska, E.

    2010-01-01

    In this chapter the recovery and recycling of secondary raw materials is explained. This chapter consists of the following parts: Paper and tetrapaks; Car wrecks; Scrap metal; Plastics; Used tires; Electrical and electronic equipment; Glass; Accumulators and batteries; Spent oil; Low-and non-waste technology.

  12. High-purity germanium crystal growing

    Hansen, W.L.; Haller, E.E.

    1982-10-01

    The germanium crystals used for the fabrication of nuclear radiation detectors are required to have a purity and crystalline perfection which is unsurpassed by any other solid material. These crystals should not have a net electrically active impurity concentration greater than 10 10 cm - 3 and be essentially free of charge trapping defects. Such perfect crystals of germanium can be grown only because of the highly favorable chemical and physical properties of this element. However, ten years of laboratory scale and commercial experience has still not made the production of such crystals routine. The origin and control of many impurities and electrically active defect complexes is now fairly well understood but regular production is often interrupted for long periods due to the difficulty of achieving the required high purity or to charge trapping in detectors made from crystals seemingly grown under the required conditions. The compromises involved in the selection of zone refining and crystal grower parts and ambients is discussed and the difficulty in controlling the purity of key elements in the process is emphasized. The consequences of growing in a hydrogen ambient are discussed in detail and it is shown how complexes of neutral defects produce electrically active centers

  13. A New Route for High-Purity Organic Materials: High-Pressure-Ramp-Induced Ultrafast Polymerization of 2-(Hydroxyethyl)Methacrylate

    Evlyukhin, E.; Museur, L.; Traore, M.; Perruchot, C.; Zerr, A.; Kanaev, A.

    2015-12-01

    The synthesis of highly biocompatible polymers is important for modern biotechnologies and medicine. Here, we report a unique process based on a two-step high-pressure ramp (HPR) for the ultrafast and efficient bulk polymerization of 2-(hydroxyethyl)methacrylate (HEMA) at room temperature without photo- and thermal activation or addition of initiator. The HEMA monomers are first activated during the compression step but their reactivity is hindered by the dense glass-like environment. The rapid polymerization occurs in only the second step upon decompression to the liquid state. The conversion yield was found to exceed 90% in the recovered samples. The gel permeation chromatography evidences the overriding role of HEMA2•• biradicals in the polymerization mechanism. The HPR process extends the application field of HP-induced polymerization, beyond the family of crystallized monomers considered up today. It is also an appealing alternative to typical photo- or thermal activation, allowing the efficient synthesis of highly pure organic materials.

  14. Method for selecting raw materials to preparing ceramic masses: application to raw material for red ceramic

    Moreno, Maria Margarita Torres; Rocha, Rogers Raphael da; Zanard, Antenor

    2012-01-01

    We studied the raw materials used in a factory building blocks, located in Cesario Lange city (SP). It extracts raw materials from various sources in the region to make the dough. The mixtures were prepared from dry milled powders based on data related to the plasticity of the raw materials. It was obtained with the apparatus Vicat-cone in order to obtain similar levels of water absorption of the samples burned at 900 deg C for all compositions. To quantify the proportion of each clay was used the Lever Rule. In this firing temperature, where sintering is mainly by diffusion from a solid state, different compositions of the same set of four raw materials resulted in similar values. (author)

  15. Raw material studies of West Central Serbia

    Vera Bogosavljević Petrović

    2014-03-01

    Full Text Available This paper deals with raw material problems in the territory of West Central Serbia geologically determined as the Čačak-Kraljevo (or West Morava basin. Our research is presented through the most striking case studies, Lojanik, Vlaška Glava and Lazac.  The Lojanik hill is a silicified forest by origin. It has occasionally been in use from the earliest periods of prehistory until today as a source of black and ochre-coloured flint, opal and silicified wood. A detailed prospection, including the mapping of surface finds using square nets, was conducted during two research campaigns.The Vlaška Glava is an open-air Palaeolithic site at which artefacts made of white, ochre, red, brown and black chert, silicified magnesite, volcanic and metamorphic rocks were found. Our research of primary and secondary geological deposits in the vicinity of the site showed equivalent raw material. We also found an interesting primary deposit of high quality bluish grey flint with outcrop activities (Workshop 1.The Lazac shaft is a contemporary magnesite mine, recently abandoned because of the high percentage of silicon-dioxide. We determined the same raw material in collections found at nearby Neolithic sites. Certain similarities between the wooden support systems of ore exploration in the Middle Ages and modern times were established at the entrance of the shaft.Our research in the territory of the West Morava basin resulted in reconstruction of some links between geological deposits and settlements and also creation of a relevant base for future raw material studies.

  16. Low-cost high purity production

    Kapur, V. K.

    1978-01-01

    Economical process produces high-purity silicon crystals suitable for use in solar cells. Reaction is strongly exothermic and can be initiated at relatively low temperature, making it potentially suitable for development into low-cost commercial process. Important advantages include exothermic character and comparatively low process temperatures. These could lead to significant savings in equipment and energy costs.

  17. Globalization determinants of raw materials markets development

    Olga Yatsenko

    2013-02-01

    Full Text Available The determinants of development of raw materials markets and the peculiarities of their formation in the terms of world economy globalization have been researched. The empirical base of research is the agricultural food market as one of the most important bases in the sphere of material production and provision of food security of the country. The important social and economic mission of the agricultural sector has been highlighted, along with the export competitiveness and import dependence of agricultural food products in the international trade. The imperative norms have been substantiated and conclusions have been drawn regarding the establishment of respective conditions for the operation of globally integrated markets in Ukraine.

  18. Raw materials for reflector graphite (for reactors)

    Wilhelmi, G.; Mindermann, D.

    1992-01-01

    The manufacturing concept for the core components of German high temperature reactor (HTR) types of graphite was previously entirely directed to the use of German tar coke (St coke). As the plants for producing this material no longer complied technically with the current environmental protection requirements, one had to assume that they would soon be shut down. To prevent bottlenecks in the erection of future HTR plants, alternative cokes produced by modern processes by Japanese manufacturers were checked for their suitability for the manufacture of reactor graphite. This report describes the investigations carried out on these materials from the safe delayed coking process. The project work, apart from analysis of the main data of the candidate coke considered, included the processing of the raw materials into directly and secondarily extruded graphite rods on the laboratory scale, including characterisation. As the results show, the material data achieved with the previous raw material can be reproduced with Japanese St coke. The tar coke LPC-A from the Nippon Steel Chemical Co., Ltd was decided on as the new standard coke for manufacturing reflector graphite. (orig.) With 15 tabs., 2 figs [de

  19. Thermal conductivity of high purity vanadium

    Jung, W.D.

    1975-01-01

    The thermal conductivity, Seebeck coefficient, and electrical resistivity of four high-purity vanadium samples were measured over the temperature range 5 to 300 0 K. The highest purity sample had a resistance ratio (rho 273 /rho 4 . 2 ) of 1524. The highest purity sample had a thermal conductivity maximum of 920 W/mK at 9 0 K and had a thermal conductivity of 35 W/mK at room temperature. At low temperatures, the thermal resistivity was limited by the scattering of electrons by impurities and phonons. The thermal resistivity of vanadium departed from Matthiessen's rule at low temperatures. The electrical resistivity and Seebeck coefficient of high purity vanadium showed no anomalous behavior above 130 0 K. The intrinsic electrical resistivity at low temperatures was due primarily to interband scattering of electrons. The Seebeck coefficient was positive from 10 to 240 0 K and had a maximum which was dependent upon sample purity

  20. Raw materials for pellets; Rohstoffe fuer Pellets

    Neumann, H.

    2008-01-15

    In order to keep the pellet prices stable, producers look for new raw materials. Sawdust as a former basis also competes with the manufacturers of chip boards and paper. Three classes of quality are discussed by the pellet manufacturers: (a) the DINplus pellet as a premium segment for which high-quality sawdust are used; (b) a wood pellet from natural wood with varying quality for the utilization in larger plants with filters; (c) the inexpensive industrial wood pellet which deviates from the DINplus commodity regarding to the ingredients and form and could be fired in larger power stations.

  1. Energies and raw materials. Letter n.28

    2007-01-01

    This letter of the DGEMP (General Direction of the Energy and the Raw Materials) deals with the following four main topics: the main recommendations of the final report of the working Group ''Factor 4'' concerning the energy policy; the energy conservation certificates as a tool of the energy control with their implication in the residential and ternary sector; the increase of the solar water heaters and heat pumps sales thanks to the tax credits; the California example facing the climatic change and the energy policy. (A.L.B.)

  2. Raw material selection for object construction

    Perlow, J

    2017-11-01

    Full Text Available on their visual appearance. In particular, we present a method for an agent to recognise the required unseen raw material images and link them to corresponding novel object images. This capability provides an agent with an increased degree of resourcefulness... construction from component parts, and in doing so we provide a benchmark for future work to compare against within Minecraft and ShapeNet domains. II. BACKGROUND Our model is inspired by Siamese neural networks, a class of neural network that includes multiple...

  3. High purity radioactive beams at the bevalac

    Alonso, J.R.; Chatterjee, A.; Tobias, C.A.

    1979-03-01

    Peripheral nuclear fragmentation reactions of primary Bevalac heavy ion beams are used to produce secondary beams of radioactive nuclei. The large cross section and small deflection of the projectile fragments lead to high production and delivery efficiency for these beams. Dispersive beam transport allows good separation and purification of the desired secondary beams. 11 C and 19 Ne beams of high purity and good intensity (almost 0.2% of the primary beam current) are presently being used for biomedical experiments

  4. Method of high purity silane preparation

    Tsuo, Y. Simon; Belov, Eugene P.; Gerlivanov, Vadim G.; Zadde, Vitali V.; Kleschevnikova, Solomonida I.; Korneev, Nikolai N.; Lebedev, Eugene N.; Pinov, Akhsarbek B.; Ryabenko, Eugene A.; Strebkov, Dmitry S.; Chernyshev, Eugene A.

    2000-01-01

    A process for the preparation of high purity silane, suitable for forming thin layer silicon structures in various semiconductor devices and high purity poly- and single crystal silicon for a variety of applications, is provided. Synthesis of high-purity silane starts with a temperature assisted reaction of metallurgical silicon with alcohol in the presence of a catalyst. Alcoxysilanes formed in the silicon-alcohol reaction are separated from other products and purified. Simultaneous reduction and oxidation of alcoxysilanes produces gaseous silane and liquid secondary products, including, active part of a catalyst, tetra-alcoxysilanes, and impurity compounds having silicon-hydrogen bonds. Silane is purified by an impurity adsorption technique. Unreacted alcohol is extracted and returned to the reaction with silicon. Concentrated mixture of alcoxysilanes undergoes simultaneous oxidation and reduction in the presence of a catalyst at the temperature -20.degree. C. to +40.degree. C. during 1 to 50 hours. Tetra-alcoxysilane extracted from liquid products of simultaneous oxidation and reduction reaction is directed to a complete hydrolysis. Complete hydrolysis of tetra-alcoxysilane results in formation of industrial silica sol and alcohol. Alcohol is dehydrated by tetra-alcoxysilane and returned to the reaction with silicon.

  5. Analytical monitoring of systems for the production of high-purity, desalinated water

    Kunert, I.

    1988-01-01

    The purity requirements to be met by high-purity water currently push the most sensitive analytical methods to their utmost limits of sensitivity. The required degree of purity of the water at present can only be achieved by application of membrane processes, and pre-purification of the feedwater to a quality corresponding to that of the raw water source. The contribution in hand discusses the analytical monitoring of the raw water treatment plant, the water treatment prior to the treatment by reverse osmosis, monitoring and control of the modules for reverse osmosis, and the monitoring of high-purity water production for the microelectronics industry. (orig./RB) [de

  6. Zone refining high-purity germanium

    Hubbard, G.S.; Haller, E.E.; Hansen, W.L.

    1977-10-01

    The effects of various parameters on germanium purification by zone refining have been examined. These parameters include the germanium container and container coatings, ambient gas and other operating conditions. Four methods of refining are presented which reproducibly yield 3.5 kg germanium ingots from which high purity (vertical barN/sub A/ - N/sub D/vertical bar less than or equal to2 x 10 10 cm -3 ) single crystals can be grown. A qualitative model involving binary and ternary complexes of Si, O, B, and Al is shown to account for the behavior of impurities at these low concentrations

  7. Energies and raw materials. The energy situation

    1997-11-01

    Statistics are given on the energy and raw materials (coal, oil, etc.) production and consumption levels in France in November 1997: primary energy total consumption has increased (mobile year) of 0.6%, at a slightly inferior rate than the rate since 3 years. Interior demand has varied depending on the energy: strong decrease for coal (- 9.3%), slight increase for petroleum products (+ 1.2%), markedly slowing down increase for gas (+ 1.4%) and moderate increase for electricity (+ 1.3%). An increase in the dollar exchange rate and a high level of oil and gas imports have induced a maintained high energy cost level with + 14% on one year, reaching 86.8 billions Francs, to be compared to 76.1 in November 1996

  8. Energies and raw materials. The energy situation

    1997-09-01

    Statistics are given on the energy and raw materials (coal, oil, etc.) production and consumption levels in France in September 1997: primary energy total consumption has increased (mobile year) of 1.1%, at the same rate since 3 years. Interior demand has varied depending on the energy: strong decrease for coal (- 5.9%), slight increase for petroleum products (+ 0.8%), strong increase for gas (+ 3.2%) and moderate increase for electricity (+ 1.7%). An increase in the dollar exchange rate and a high level of oil and gas imports have induced a record energy cost level with + 30% on one year, reaching 89.2 billions Francs, to be compared to 68.5 in September 1996

  9. Shock loading influence on mechanical behavior of high purity iron

    Buy, Francois; Voltz, Christophe

    2004-01-01

    This paper proposes the analysis of shock wave effects for high purity iron. The method developed is based on the characterization of the mechanical behavior of as received and shocked material. Shock effect is generated through plate impact tests performed in the range of 4 GPa to 39 GPa on a single stage light gas gun or a powder gun. Therefore, as-received and impacted materials are characterized. A formalism proposed by J.R.Klepaczko and based on physical relations has been adopted to describe stress strain curves

  10. New raw materials improve packing sealing efficiency

    Igel, B.; McKeague, L.

    2012-01-01

    End-users and OEM's using or manufacturing on/off and control valves expect a permanent and effective increase in service life together with an increased sealing capability while at the same time minimizing maintenance concerns. Developing materials which provide consistency and repeatability are essential characteristics to optimizing valve performance. “New Generation” materials and yarn allow us to meet this growing demand while complying with the requirements related to chemical purity and an increased level of safety to both plant workers and equipment in the nuclear environment. Through R&D initiatives and developments in new and improved raw materials; a new mechanical packing generation which optimizes friction coefficients and extended life cycle has been introduced to the industry. Lower friction values drastically optimize actuator effort and size improving efficiency for stem operation with significant improvements in flow control of fluids. Combined with new and improved procedures (installation, torque levels and consolidation recommendations), this new packing generation has provided significant improvement in the mechanical behavior of packing materials (independent tests carried out in collaboration with AECL and CETIM) this has provided the opportunity to develop successful Valve Enhancement Programs which offer improved efficiency, valve operation and repeatability. These NEW generation yarns are available with or without wire reinforcement depending on specific operating parameters and conditions. The purpose of this presentation is to demonstrate that new generation material(s). Which are available to the industry for AOV, MOV and Manual valves? - To highlight the steps taken in R&D and manufacturing contributing to the much improved yarns and finished packing products. - Comply and are designed to meet the stringent requirements in the nuclear industry - Simplify valve maintenance without risk to safety or performance - Increase service

  11. Aerospace Fuels From Nonpetroleum Raw Materials

    Palaszewski, Bryan A.; Hepp, Aloysius F.; Kulis, Michael J.; Jaworske, Donald A.

    2013-01-01

    Recycling human metabolic and plastic wastes minimizes cost and increases efficiency by reducing the need to transport consumables and return trash, respectively, from orbit to support a space station crew. If the much larger costs of transporting consumables to the Moon and beyond are taken into account, developing waste recycling technologies becomes imperative and possibly mission enabling. Reduction of terrestrial waste streams while producing energy and/or valuable raw materials is an opportunity being realized by a new generation of visionary entrepreneurs; several relevant technologies are briefly compared, contrasted and assessed for space applications. A two-step approach to nonpetroleum raw materials utilization is presented; the first step involves production of supply or producer gas. This is akin to synthesis gas containing carbon oxides, hydrogen, and simple hydrocarbons. The second step involves production of fuel via the Sabatier process, a methanation reaction, or another gas-to-liquid technology, typically Fischer-Tropsch processing. Optimization to enhance the fraction of product stream relevant to transportation fuels via catalytic (process) development at NASA Glenn Research Center is described. Energy utilization is a concern for production of fuels whether for operation on the lunar or Martian surface, or beyond. The term green relates to not only mitigating excess carbon release but also to the efficiency of energy usage. For space, energy usage can be an essential concern. Another issue of great concern is minimizing impurities in the product stream(s), especially those that are potential health risks and/or could degrade operations through catalyst poisoning or equipment damage; technologies being developed to remove heteroatom impurities are discussed. Alternative technologies to utilize waste fluids, such as a propulsion option called the resistojet, are discussed. The resistojet is an electric propulsion technology with a powered

  12. Neutron activation analysis of high purity substances

    Gil'bert, Eh.N.

    1987-01-01

    Peculiarities of neutron-activation analysis (NAA) of high purity substances are considered. Simultaneous determination of a wide series of elements, high sensitivity (the lower bound of determined contents 10 -9 -10 -10 %), high selectivity and accuracy (Sr=0.10-0.15, and may be decreased up to 0.001), possibility of analysis of the samples from several micrograms to hundreds of grams, simplicity of calibration may be thought NAA advantages. Questions of accounting of NAA systematic errors associated with the neutron flux screening by the analysed matrix and with production of radionuclides of determined elements from accompanying elements according to concurrent nuclear reactions, as well as accounting of errors due to self-absorption of recorded radiation by compact samples, are considered

  13. Neutron activation analysis of high purity tellurium

    Gil'bert, Eh.N.; Verevkin, G.V.; Obrazovskij, E.G.; Shatskaya, S.S.

    1980-01-01

    A scheme of neutron activation analysis of high purity tellurium is developed. Weighed amount of Te (0.5 g) is irradiated for 20-40 hr in the flux of 2x10 13 neutron/(cm 2 xs). After decomposition of the sample impurities of gold and palladium are determined by the extraction with organic sulphides. Tellurium separation from the remaining impurities is carried out by the extraction with monothiobenzoic acid from weakly acidic HCl solutions in the presence of iodide-ions, suppressing silver extraction. Remaining impurity elements in the refined product are determined γ-spectrometrically. The method allows to determine 34 impurities with determination limits 10 -6 -10 -11 g

  14. Uranium as Raw Material for Nuclear Energy

    Lelek, V.

    2006-01-01

    There is lot of information bringing our attention to the problem of limited raw material resources. Fortunately uranium for nuclear energy is very concentrated source and that is why its transport brings no problems and could be realized from anywhere. Second question is if overall resources are available for current nuclear energy development. Data documenting reasons for nowadays price growth are presenting and it is clearly shown that the most probable explanation is that there is gap in new uranium mines preparation and the lot of smaller mines were closed in the period of low uranium prices. Conclusion is that there is at least for the first half of this century even for thermal reactors enough uranium. Situation could be changed if there will massive production of liquid fuel using hydrogen, produced through nuclear heating. Public information about former military uranium resources are also included. Contemporary about one half of US nuclear power-stations is using high enriched uranium diluted with natural uranium - it is expected to continue this way up to 2012. Uranium is complicated market (Authors)

  15. Dates as raw material for agricultural distilleries

    Laczynski, B

    1971-01-01

    Pit-containing dates had 88.0 to 89.2% dry matter, 41.7 to 47.5% sucrose, and 2.1 to 2.9% total protein. The mechanical broken charges of raw material were steamed, dispersed to a suspension of 15 to 17/sup 0/ Balling and pH 4.8 to 5.0, enriched with P and N, inoculated with 5 to 7 % of yeast suspension, and acidified to pH > 3.5. Thermophilic yeast cultivated at 27/sup 0/ and fermented below 30/sup 0/ for 2 days gave best results. The fermented liquor had a pH > 3.5, apparent density of 2.0/sup 0/, and contained 7.5 to 9.0 EtOH. From 100 kg dates were obtained 280 t0 340 l of the 15 to 17/sup 0/ dispersion and 320 to 360 l residue containing (per l) 6.0 to 8.5 g protein and 0.04 oat units. EtOH yield (l/quintal) was 914 for potatoes, 28.54 for molasses, 36.29 for cereals, 25.15 for dates, and 18.53 for malt.

  16. High belite cement from alternative raw materials

    Ghorab, H. Y.

    2014-05-01

    Full Text Available Three high belite laboratory clinkers were prepared from traditional and alternative raw materials. Reference clinker was obtained from 77% limestone, 11% sandy clays, 11% fatty clays and 1% iron scales. The fatty clays were replaced by red brick powder in the raw meal of the second clinker and were lowered to 2% with the replacement of 10% of the limestone by egg shells in the third clinker. The SEM examination revealed clear presence of crossed striae and twinning in the rounded belite grains of the reference clinker caused by the transformation of the α´-belite to the β polymorph. Striae were weaker in the second and third clinkers indicating a probable stabilization of the α ‘-belite polymorph. Compressive strength of the respective cements were attained first after 28 days and the early strength did not improve with increasing fineness. Higher compressive strength values were found for the cement prepared from second clinker.Se han preparado tres clinkeres de laboratorio con altos contenidos en belita a partir de materias primas tradicionales y alternativas. El clinker de referencia se obtuvo a partir de una mezcla de caliza, arcillas arenosas y grasas y limaduras de hierro. Las arcillas grasas fueron sustituidas por polvo de ladrillo rojo en la preparación del segundo clinker, y en el tercero el contenido de arcilla grasa fue de solo un 2% y parte de la caliza fue sustituida por cascara de huevo. El estudio realizado por SEM muestra superficies estriadas alrededor de los granos de belita que indican una transformación del polimorfo α´ a la forma β-C₂S, durante el enfriamiento. Esas estrías son menos marcadas en el segundo y tercer clinker, indicando, una estabilización del polimorfo α´-C₂S. Los valores de resistencias a compresión de los correspondientes cementos, a 28 días de curado, no se ven incrementados por la finura de dichos cementos. Las mayores resistencias se obtuvieron en el cemento preparado a partir del cl

  17. Scoping Future Policy Dynamics in Raw Materials Through Scenarios Testing

    Correia, Vitor; Keane, Christopher; Sturm, Flavius; Schimpf, Sven; Bodo, Balazs

    2017-04-01

    The International Raw Materials Observatory (INTRAW) project is working towards a sustainable future for the European Union in access to raw materials, from an availability, economical, and environmental framework. One of the major exercises for the INTRAW project is the evaluation of potential future scenarios for 2050 to frame economic, research, and environmental policy towards a sustainable raw materials supply. The INTRAW consortium developed three possible future scenarios that encompass defined regimes of political, economic, and technological norms. The first scenario, "Unlimited Trade," reflects a world in which free trade continues to dominate the global political and economic environment, with expectations of a growing demand for raw materials from widely distributed global growth. The "National Walls" scenario reflects a world where nationalism and economic protectionism begins to dominate, leading to stagnating economic growth and uneven dynamics in raw materials supply and demand. The final scenario, "Sustainability Alliance," examines the dynamics of a global political and economic climate that is focused on environmental and economic sustainability, leading towards increasingly towards a circular raw materials economy. These scenarios were reviewed, tested, and provided simulations of impacts with members of the Consortium and a panel of global experts on international raw materials issues which led to expected end conditions for 2050. Given the current uncertainty in global politics, these scenarios are informative to identifying likely opportunities and crises. The details of these simulations and expected responses to the research demand, technology investments, and economic components of raw materials system will be discussed.

  18. Determination Of Work Indexes Of Basic Ceramic Raw Materials

    İPEK, Halil; UÇBAŞ, Yaşar

    2017-01-01

    In this study, the grindability of basic ceramic raw materials have been investigated by using Bond grindability test and the results have been compared. Bond grindability test results show that work indexes of raw materials are dependent on their hardnesses.

  19. 7 CFR 58.332 - Segregation of raw material.

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Segregation of raw material. 58.332 Section 58.332... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Operations and Operating Procedures § 58.332 Segregation of raw material. The milk and cream received at the dairy plant shall meet...

  20. Raw material supply: challenge and chance for economy and state

    Casper, W

    1976-01-01

    The imprint left by the 1973 oil embargo makes all nations aware of their dependence upon this and other raw materials. The author says the brunt of the embargo has dealt a heavier blow than has been realized on industrial nations and developing countries alike. The drastic decline of raw material prices has had threatening consequences for a number of raw-material-producing developing countries, making some nations unite for the purpose of market regulation. The cartel-like union of copper-producing countries is cited; producers of bauxite, iron ore, and tungsten have united; and some producers of tin have united. So far, the attempt to apply the oil strategy to other raw materials has not achieved the desired results; however, raw materials are no longer just a phase of the industrial process but have become a political matter of prime importance. (MCW)

  1. Development of high purity large forgings for nuclear power plants

    Tanaka, Yasuhiko; Sato, Ikuo

    2011-01-01

    The recent increase in the size of energy plants has been supported by the development of manufacturing technology for high purity large forgings for the key components of the plant. To assure the reliability and performance of the large forgings, refining technology to make high purity steels, casting technology for gigantic ingots, forging technology to homogenize the material and consolidate porosity are essential, together with the required heat treatment and machining technologies. To meet these needs, the double degassing method to reduce impurities, multi-pouring methods to cast the gigantic ingots, vacuum carbon deoxidization, the warm forging process and related technologies have been developed and further improved. Furthermore, melting facilities including vacuum induction melting and electro slag re-melting furnaces have been installed. By using these technologies and equipment, large forgings have been manufactured and shipped to customers. These technologies have also been applied to the manufacture of austenitic steel vessel components of the fast breeder reactors and components for fusion experiments.

  2. Development of high purity large forgings for nuclear power plants

    Tanaka, Yasuhiko; Sato, Ikuo

    2011-10-01

    The recent increase in the size of energy plants has been supported by the development of manufacturing technology for high purity large forgings for the key components of the plant. To assure the reliability and performance of the large forgings, refining technology to make high purity steels, casting technology for gigantic ingots, forging technology to homogenize the material and consolidate porosity are essential, together with the required heat treatment and machining technologies. To meet these needs, the double degassing method to reduce impurities, multi-pouring methods to cast the gigantic ingots, vacuum carbon deoxidization, the warm forging process and related technologies have been developed and further improved. Furthermore, melting facilities including vacuum induction melting and electro slag re-melting furnaces have been installed. By using these technologies and equipment, large forgings have been manufactured and shipped to customers. These technologies have also been applied to the manufacture of austenitic steel vessel components of the fast breeder reactors and components for fusion experiments.

  3. Material Classification Using Raw Time-of-Flight Measurements

    Su, Shuochen; Heide, Felix; Swanson, Robin J.; Klein, Jonathan; Callenberg, Clara; Hullin, Matthias; Heidrich, Wolfgang

    2016-01-01

    We propose a material classification method using raw time-of-flight (ToF) measurements. ToF cameras capture the correlation between a reference signal and the temporal response of material to incident illumination. Such measurements encode unique

  4. Sulfur Release from Cement Raw Materials during Solid Fuel Combustion

    Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter

    2011-01-01

    During combustion of solid fuels in the material inlet end of cement rotary kilns, local reducing conditions can occur and cause decomposition of sulfates from cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2 concentration, which may cause...... deposit formation in the kiln system. SO2 release from cement raw materials during combustion of solid fuels has been studied experimentally in a high temperature rotary drum. The fuels were tire rubber, pine wood, petcoke, sewage sludge, and polypropylene. The SO2 release from the raw materials...

  5. Investigation on pyrolysis of some organic raw materials

    Purevsuren B

    2017-02-01

    Full Text Available We have been working on pyrolysis of some organic raw materials including different rank coals, oil shale, wood waste, animal bone, cedar shell, polypropylene waste, milk casein and characterization of obtained hard residue, tar and pyrolytic water and gas after pyrolysis. The technical characteristics of these organic raw materials have been determined and the thermal stability characteristics such as thermal stability indices (T5% and T25% determined by using thermogravimetric analysis. The pyrolysis experiments were performed at different heating temperatures and the yields of hard residue, tar, pyrolysis water and gaseous products were determined and discussed. The main technical characteristics of hard residue of organic raw materials after pyrolysis have been determined and the adsorption ability of pyrolysis hard residue and its activated carbon of organic raw materials also determined. The pyrolysis tars of organic raw materials were distilled in air condition and determined the yields of obtained light, middle and heavy fractions and bitumen like residue with different boiling temperature. This is the first time to investigate the curing ability of pyrolysis tars of organic raw materials for epoxy resin and the results of these experiments showed that only tar of milk casein has the highest (95.0%, tar of animal bone has certain (18.70% and tars of all other organic raw materials have no curing ability for epoxy resin.

  6. Synthesis of high purity rutile nanoparticles from medium-grade Egyptian natural ilmenite

    Mohamed G. Shahien

    2015-09-01

    Full Text Available The Egyptian magmatic ilmenite is classified as a medium-grade ore. The present work is an attempt to produce a high-quality TiO2 that can be used in several industries from this medium-grade raw material using the mechanical activation, carbothermic reduction, hydrochloric acid leaching and calcination. A mixture from the ilmenite (FeTiO3 and activated carbon was milled for 30 h. This mixture was annealed at 1200 °C for one hour and the product was leached by hydrochloric acid and calcined at 600 °C for two hours. The role of the ball milling was to grind the raw ilmenite to obtain the nano size, and the carbothermic reduction was to reduce all the Fe-Ti phases to a mixture from Fe metal and TiO2. Leaching procedure was carried out to remove all the Fe metal and obtain a high-grade TiO2. After leaching and calcination of the milled and annealed mixture of FeTiO3/C under the optimal conditions, TiO2 nanoparticles with a size of 10–100 nm and purity more than 95% were obtained. The qualifications of the synthesized high purity rutile nanoparticles from the Egyptian natural ilmenite match the conditions of many industrial applications.

  7. VERAM - Vision and Roadmap for European Raw Materials

    Baumgarten, Wibke; Vashev, Boris

    2017-04-01

    The overall objective of VERAM project is to produce a Vision and Roadmap for European Raw Materials in 2050 based on raw materials research and innovation (R&I) coordination. Two leading European Technology Platforms (ETPs): ETP SMR (Sustainable Minerals Resources) and FTP (Forest Technology Platform) are joining forces to develop a common vison and roadmap with the support of ECTP (European Construction Technology Platform), represented by UNIVPM, SusChem (ETP for Sustainable Chemistry), represented by Cefic, EuMaT (Advanced Materials ETP), represented by VITO, ERAMIN 2, represented by Research Centre JUELICH and WoodWisdom Network Plus represented by the Agency for Renewable Resources (FNR). This partnership provides VERAM with expertise from downstream applications and additional knowledge on non-biotic and biotic raw materials. The project encourages capacity building as well as transfer of knowledge. It expects to provide an innovation reference point for the European Institute of Innovation & Technology (EIT) Raw Materials (formerly the KIC Raw MatTERS), to coordinate the network involved in the European Innovation Partnership (EIP) on Raw Materials Commitments and relevant proposals funded under Horizon 2020. It provides a platform for identifying gaps and complementarities and enables their bridging. VERAM will be able to advise the European Commission and Member States on future research needs and policies to stimulate innovation and assist in overcoming fragmentation in the implementing the EIP Raw Materials Strategic Implementation Plan. VERAM looks for mutually beneficial information exchange, encourages cross-fertilization between actions undertaken by different raw material industries, and expects to accelerate exploitation of breakthrough innovations. One of the main outcomes of the project is the presentation of a common long term 2050 Vision and Roadmap for relevant raw materials including metals, industrial minerals and aggregates and wood. The

  8. Basic Thermal Parameters of Selected Foods and Food Raw Materials

    Monika Božiková; Ľubomír Híreš; Michal Valach; Martin Malínek; Jan Mareček

    2017-01-01

    In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of ...

  9. High purity zirconium obtainment through the iodine compounds transport method

    Bolcich, J.C.; Zuzek, E.; Dutrus, S.M.; Corso, H.L.

    1987-01-01

    This paper describes the experimental method and the equipment designed, constructed and actually applied for the high purity zirconium obtainment from a zirconium sponge of the nuclear type. The mechanism of purification is based on the impure metal attack with gaseous iodine (at 200 deg C) to obtain zirconium tetra iodine as main product which is then transformed into a pure zirconium base (at 1000-1300 deg C), precipitating the metallic zirconium and releasing the gaseous iodine. From the first experiences carried out, pure zirconium has been obtained from an initial filament of 0.5 mm of diameter as well as wires up to 2.5 mm of diameter. This work presents the results from the studies and analysis made to characterize the material obtained. Finally, the refining methods to which the zirconium produced may be submitted so as to optimize the final purity are discussed. (Author)

  10. Tracing and control of raw materials sourcing for vaccine manufacturers.

    Faretra Peysson, Laurence

    2010-05-01

    The control of the raw materials used to manufacture vaccines is mandatory; therefore, a very clear process must be in place to guarantee that raw materials are traced. Those who make products or supplies used in vaccine manufacture (suppliers of culture media, diagnostic tests, etc.) must apply quality systems proving that they adhere to certain standards. ISO certification, Good Manufacturing Practices for production sites and the registration of culture media with a 'Certificate of Suitability' from the European Directorate for the Quality of Medicines and Healthcare are reliable quality systems pertaining to vaccine production. Suppliers must assure that each lot of raw materials used in a product that will be used in vaccine manufacture adheres to the level of safety and traceability required. Incoming materials must be controlled in a single 'Enterprise Resource Planning' system which is used to document important information, such as the assignment of lot number, expiration date, etc. Ingredients for culture media in particular must conform to certain specifications. The specifications that need to be checked vary according to the ingredient, based on the level of risk. The way a raw material is produced is also important, and any aspect relative to cross-contamination, such as the sanitary measures used in producing and storing the raw material must be checked as well. In addition, suppliers can reduce the risk of viral contamination of raw materials by avoiding purchases in countries where a relevant outbreak is currently declared. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

  11. Glucose from a cellulose-containing raw material

    Feniksova, R V

    1977-01-01

    Glucose was produced by mixing the raw material with an enzyme and water, enzymic hydrolysis of raw material, and separation of the hydrolyzate. To increase the yield of glucose, the hydrolysis took place in 2 stages: at the 1st stage, the hydrolysis was continued until the mixture of glucose and oligosaccharides was obtained under the influence of an active enzyme (1 to 20 units/g of cellulose present in the raw material); at the 2nd stage, cellulase immobilized on an insoluble carrier (by covalent bonds) was used for the hydrolysis of oligosaccharides. The hydromodulus of the suspension of cellulose-containing raw material was maintained 5 to 30. A carrier nonhydrolyzable by cellulase, for instance a homogenious macroporous Aerosil gel, a porous glass, or porous ceramics, was used.

  12. ICE CREAM WITH A COMBINED COMPOSITION OF RAW MATERIALS

    O. E. Khodyreva

    2013-01-01

    Full Text Available Dairy products are the product of daily demand. Nowadays actively assimilate new types of raw materials, tech-nology, formulation. One of the propagation methods of enriching dairy products is a combination of milk and vegetable raw materials. The possibility of making a concentrated paste of Jerusalem artichoke in dairy products was investigated. The ice cream sundae "Vanilla" was chosen as the object of research.

  13. Refining of raw materials, lignite present economic problems

    Schirmer, G.

    1985-06-01

    East Germany seeks an economic intensification program that involves refining raw materials to a higher level. Lignite briquetting prior to liquefaction and gasification illustrates both the theoretical and practical aspects of that goal and also introduces questions of secure supplies. The author describes the special labor processes, use of technology, recycling of waste materials, and other new problems that the approach entails as the refined raw materials become new materials or energy sources. Economics based on the value of the refined product and the cost of the materials determine the degree of refinement. The concept also involves the relationship of producer and user as profits increase.

  14. Raw material ‘criticality’—sense or nonsense?

    Frenzel, M; Kullik, J; Reuter, M A; Gutzmer, J

    2017-01-01

    The past decade has seen a resurgence of interest in the supply security of mineral raw materials. A key to the current debate is the concept of ‘criticality’. The present article reviews the criticality concept, as well as the methodologies used in its assessment, including a critical evaluation of their validity in view of classical risk theory. Furthermore, it discusses a number of risks present in global raw materials markets that are not captured by most criticality assessments. Proposed measures for the alleviation of these risks are also presented. We find that current assessments of raw material criticality are fundamentally flawed in several ways. This is mostly due to a lack of adherence to risk theory, and highly limits their applicability. Many of the raw materials generally identified as critical are probably not critical. Still, the flaws of current assessments do not mean that the general issue of supply security can simply be ignored. Rather, it implies that new assessments are required. While the basic theoretical framework for such assessments is outlined in this review, detailed method development will require a major collaborative effort between different disciplines along the raw materials value chain. In the opinion of the authors, the greatest longer-term challenge in the raw materials sector is to stop, or counteract the effects of, the escalation of unit energy costs of production. This issue is particularly pressing due to its close link with the renewable energy transition, requiring more metal and mineral raw materials per unit energy produced. The solution to this problem will require coordinated policy action, as well as the collaboration of scientists from many different fields—with physics, as well as the materials and earth sciences in the lead. (topical review)

  15. Raw material ‘criticality’—sense or nonsense?

    Frenzel, M.; Kullik, J.; Reuter, M. A.; Gutzmer, J.

    2017-03-01

    The past decade has seen a resurgence of interest in the supply security of mineral raw materials. A key to the current debate is the concept of ‘criticality’. The present article reviews the criticality concept, as well as the methodologies used in its assessment, including a critical evaluation of their validity in view of classical risk theory. Furthermore, it discusses a number of risks present in global raw materials markets that are not captured by most criticality assessments. Proposed measures for the alleviation of these risks are also presented. We find that current assessments of raw material criticality are fundamentally flawed in several ways. This is mostly due to a lack of adherence to risk theory, and highly limits their applicability. Many of the raw materials generally identified as critical are probably not critical. Still, the flaws of current assessments do not mean that the general issue of supply security can simply be ignored. Rather, it implies that new assessments are required. While the basic theoretical framework for such assessments is outlined in this review, detailed method development will require a major collaborative effort between different disciplines along the raw materials value chain. In the opinion of the authors, the greatest longer-term challenge in the raw materials sector is to stop, or counteract the effects of, the escalation of unit energy costs of production. This issue is particularly pressing due to its close link with the renewable energy transition, requiring more metal and mineral raw materials per unit energy produced. The solution to this problem will require coordinated policy action, as well as the collaboration of scientists from many different fields—with physics, as well as the materials and earth sciences in the lead.

  16. Pellet production from agricultural raw materials - A systems study

    Nilsson, Daniel; Bernesson, Sven; Hansson, Per-Anders [Department of Energy and Technology, Swedish University of Agricultural Sciences, P.O. Box 7032, SE-75007 Uppsala (Sweden)

    2011-01-15

    The demand for biofuel pellets has increased considerably in recent years, causing shortage of the traditional raw materials sawdust and wood shavings. In this study, the costs and energy requirements for the production of pellets from agricultural raw materials were analysed. The materials studied were Salix, reed canary grass, hemp, straw, screenings, rape-seed meal, rape cake and distiller's waste. Four production scales were analysed, having an annual output of 80,000, 8000, 800 and 80 tonnes of pellets per year. It was concluded that the raw materials of greatest interest were Salix and reed canary grass. They had competitive raw material costs and acceptable fuel properties and could be mixed with sawdust in existing large-scale pelleting factories. Straw had low production costs but can cause serious ash-related problems and should, as also is the case for screenings, be avoided in small-scale burners. Hemp had high raw material costs and is of less commercial interest, while distiller's waste, rape-seed meal and rape cake had higher alternative values when used as protein feed. The scale of production had a crucial influence on production costs. The machinery was used much more efficiently in large-scale plants, resulting in clear cost savings. Small-scale pelleting, both static and mobile, required cheap raw materials, low labour costs and long utilisation times to be profitable. In most cases, briquetting would be more commercially viable. The energy use in manufacturing pellets from air-dried crops was generally no higher than when moist sawdust was used as the raw material. (author)

  17. Uninterrupted heat-treatment of starch raw materials

    Bronshtein, D Z

    1958-01-01

    A setup is presented, with a Rekord grinder, a Khronos scale, and other equipment of Soviet manufacture, in which oats, rye, wheat, and other grains are treated at 42 to 45 degrees prior to their use as raw materials in the ethanol industry. These materials are analyzed with respect to H/sub 2/O, starch, bulk, weight, screen analysis, and the final ethanol yields/ton of such raw materials. In a three year run in plant, this heat-treatment was advantageous, as compared to the former treatment of the starch materials.

  18. Uninterrupted heat-treatment of starch raw materials

    Bronshtein, D Z

    1958-01-01

    A setup is presented, with a Rekord grinder, a Khronos scale, and other equipment of Soviet manufacture, in which oats, rye, wheat, and other grains are treated at 42 to 45/sup 0/ prior to their use as raw materials in the ethanol industry. These materials are analyzed with respect to H/sub 2/O, starch, bulk weight, screen analysis, and the final ethanol yields/ton of such raw materials. In a three year run in a plant, this heat-treatment was advantageous, as compared to the former treatment of the starch materials.

  19. Basic Thermal Parameters of Selected Foods and Food Raw Materials

    Monika Božiková

    2017-01-01

    Full Text Available In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of thermal parameters measurement for various foods and food raw materials as: granular materials – corn flour and wheat flour; fruits, vegetables and fruit products – grated apple, dried apple and apple juice; liquid materials – milk, beer etc. Measurements were performed in two temperature ranges according to the character of examined material. From graphical relations of thermophysical parameter is evident, that thermal conductivity and diffusivity increases with temperature and moisture content linearly, only for granular materials were obtained non‑linear dependencies. Results shows, that foods and food raw materials have different thermal properties, which are influenced by their type, structure, chemical and physical properties. From presented results is evident, that basic thermal parameters are important for material quality detection in food industry.

  20. Electron beam welding of high-purity copper accelerator cells

    Delis, K.; Haas, H.; Schlebusch, P.; Sigismund, E.

    1986-01-01

    The operating conditions of accelerator cells require high thermal conductivity, low gas release in the ultrahigh vacuum, low content of low-melting metals and an extremely good surface quality. In order to meet these requirements, high-purity copper (OFHC, Grade 1, according to ASTM B 170-82 and extra specifications) is used as structural material. The prefabricated components of the accelerator cells (noses, jackets, flanges) are joined by electron beam welding, the weld seam being assessed on the basis of the same criteria as the base material. The welding procedures required depend, first, on the material and, secondly, on the geometries involved. Therefore experimental welds were made first on standardized specimens in order to study the behaviour of the material during electron beam welding and the influence of parameter variations. The welded joints of the cell design were planned on the basis of these results. Seam configuration, welding procedures and the parameters were optimized on components of original geometry. The experiments have shown that high-quality joints of this grade of copper can be produced by the electron beam welding process, if careful planning and preparation of the seams and adequate containment of the welding pool are assured. (orig.)

  1. Incentivizing secondary raw material markets for sustainable waste management.

    Schreck, Maximilian; Wagner, Jeffrey

    2017-09-01

    Notwithstanding several policy initiatives in many countries over a number of years, there remains a general sense that too much municipal solid waste is generated and that too much of the waste that is generated is landfilled. There is an emerging consensus that a sustainable approach to waste management requires further development of secondary raw material markets. The purpose of this paper is to propose a theoretical economic model that focuses upon this stage of a sustainable waste management program and explores policy options that could motivate efficiency in secondary raw material markets. In particular, we show how firm profit and social welfare optimizing objectives can be reconciled in a two-product market of waste management processes: landfilling and material reclamation. Our results provide theoretical support for building out recent Circular Economy initiatives as well as for the relatively recent emergence of landfill mining as a means for procuring secondary raw materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Growth and characterization of high-purity SiC single crystals

    Augustine, G.; Balakrishna, V.; Brandt, C. D.

    2000-04-01

    High-purity SiC single crystals with diameter up to 50 mm have been grown by the physical vapor transport method. Finite element analysis was used for thermal modeling of the crystal growth cavity in order to reduce stress in the grown crystal. Crystals are grown in high-purity growth ambient using purified graphite furniture and high-purity SiC sublimation sources. Undoped crystals up to 50 mm in diameter with micropipe density less than 100 cm -2 have been grown using this method. These undoped crystals exhibit resistivities in the 10 3 Ω cm range and are p-type due to the presence of residual acceptor impurities, mainly boron. Semi-insulating SiC material is obtained by doping the crystal with vanadium. Vanadium has a deep donor level located near the middle of the band gap, which compensates the residual acceptor resulting in semi-insulating behavior.

  3. Raw materials in the manufacture of biotechnology products: regulatory considerations.

    Cordoba-Rodriguez, Ruth

    2010-01-01

    The Food and Drug Administration's Pharmaceutical cGMPs for the 21st Century initiative emphasizes science and risk-based approaches in the manufacture of drugs. These approaches are reflected in the International Conference on Harmonization (ICH) guidances ICH Q8, Q9, and Q10 and encourage a comprehensive assessment of the manufacture of a biologic, including all aspects of manufacture that have the potential to affect the finished drug product. Appropriate assessment and management of raw materials are an important part of this initiative. Ideally, a raw materials program should strive to assess and minimize the risk to product quality. With this in mind, risk-assessment concepts and control strategies will be discussed and illustrated by examples, with an emphasis on the impact of raw materials on cell substrates. Finally, the life cycle of the raw material will be considered, including its potential to affect the drug product life cycle. In this framework, the supply chain and the vendor-manufacturer relationship will be explored as important parts of an adequate raw materials control strategy.

  4. European initiative on cdio in raw material programmes

    Edelbro, Catrin; Hulthén, Erik; Clausen, Elisabeth; Tanner, David; Herrera Herbert, Juan; Jonsson, Kristina; Bealieu, Stephan; Kamp, A.; Försth, Michael

    2017-01-01

    One of five Knowledge and Innovation Communities (KICs), was launched in Europe in 2014 and has its focus on exploration, extraction, mineral processing, metallurgy, recycling and material substitution of raw materials. To reach the vision, where the European Union’s industrial strength is based on

  5. Chemical analysis of high purity graphite

    1993-03-01

    The Sub-Committee on Chemical Analysis of Graphite was organized in April 1989, under the Committee on Chemical Analysis of Nuclear Fuels and Reactor Materials, JAERI. The Sub-Committee carried out collaborative analyses among eleven participating laboratories for the certification of the Certified Reference Materials (CRMs), JAERI-G5 and G6, after developing and evaluating analytical methods during the period of September 1989 to March 1992. The certified values were given for ash, boron and silicon in the CRM based on the collaborative analysis. The values for ten elements (Al, Ca, Cr, Fe, Mg, Mo, Ni, Sr, Ti, V) were not certified, but given for information. Preparation, homogeneity testing and chemical analyses for certification of reference materials were described in this paper. (author) 52 refs

  6. Strategic raw materials. Risk management; Strategische Rohstoffe. Risikovorsorge

    Bertau, Martin [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Technische Chemie; Gutzmer, Jens [Helmholtz-Institut fuer Ressourcentechnologie Freiberg (Germany); Matschullat, Joerg (ed.) [Technische Univ. Bergakademie Freiberg (Germany). Interdisziplinaeres Oekologisches Zentrum (IOeZ); Kausch, Peter

    2014-07-01

    This volume is divided into four chapters: (1) Raw material management, (2) Primary raw materials, (3) Secondary raw materials and recycling, (4). Processing and products. The topics for the chapter ''Raw material management'' are: Substitution of raw materials - framework conditions and implementation; Thales: Strategic raw materials; Time for cooperation between the EU and China in raw materials policy; Availability of elements for the semiconductor industry; Market price risks of raw material-intensive companies - identification and management. The topics on the second item ''Primary raw materials'' are: The supply of economic-critical raw materials - A search and analysis for causes; Lithium extraction from primary raw materials - state and perspectives; The global market of rare earths - A balancing act; Rare earth deposits in Namibia; New technologies in exploration and discovery - Focus on activities in Europe. The third chapter, ''Secondary Raw Materials and Recycling'', covered the topics: Technology metals - Systemic Requirements along the recycling chain; Integrated re-use of high-tech and greentech wastes; From the sewage sludge ash to the phosphorus fertilizer RecoPhos P38 in the stress field of waste, fertilizer and soil protection. In chapter 4. ''Processing and products'' are the topics: Treatment and processing of rare earth metals; Processing of mineral resources - opportunities and challenges; Consequences of modern germanium chemistry; Strategic resources - Risk management. A review and outlook with a pinch of fantasy.. [German] Dieser Band gliedert sich in vier Kapitel: (1) Rohstoffwirtschaft, (2) Primaere Rohstoffe, (3) Sekundaere Rohstoffe und Recycling,(4). Verarbeitung und Produkte. Die Themen zum Kapitel ''Rohstoffwirtschaft'' sind: Substitution von Rohstoffen - Rahmenbedingungen und Umsetzung; Thales: Strategische Rohstoffe; Zeit fuer

  7. Natural gas as raw material for industrial development

    Kvisle, Steinar

    2006-01-01

    Industrial development based on natural gas has broad, industrial implications. Norway has a vital industry based on natural gas as raw material, here under Ormen Lange, Snoehvit LNG, Tjeldbergodden and Petrochemical Grenland. The petrochemical industry has challenges, e.g. the cost of raw materials and energy, localization related to the markets, and recruitment, but considerable investments are made in the sector. The Northern areas in Norway may have special challenges related to bringing the product to the market. Solutions to this challenge are in LNG (liquid natural gas), GTL (gas to liquids), and GTO (gas to olefins)

  8. Production of high purity aluminas: II - Characterization

    Franceschini Filho, D.F.; Morschbacker, A.L.R.C.; Fonseca, M.C.; Mello, R.T. de; Ferreira Filho, J.M.

    1987-01-01

    This paper presents a characterization study on various samples of aluminum hidroxyde (pseudoboemite). Results of X-ray diffraction (identification, mean crystal size, degree of crystallinity); BET surface area and loss of ignition of the samples are displayed. The degree of crystallinity is found to be of great usefullness in the characterization of this kind of material. We point out the variety of products that can be obtained with the method of preparation used. (Author) [pt

  9. Obtaining high purity silica from rice hulls

    José da Silva Júnior

    2010-01-01

    Full Text Available Many routes for extracting silica from rice hulls are based on direct calcining. These methods, though, often produce silica contaminated with inorganic impurities. This work presents the study of a strategy for obtaining silica from rice hulls with a purity level adequate for applications in electronics. The technique is based on two leaching steps, using respectively aqua regia and Piranha solutions, which extract the organic matrix and inorganic impurities. The material was characterized by Fourier-transform infrared spectroscopy (FTIR, powder x-ray diffraction (XRD, x-ray fluorescence (XRF, scanning electron microscopy (SEM, particle size analysis by laser diffraction (LPSA and thermal analysis.

  10. Control Analysis Of Tobacco Raw Material Supplies Using Eoq Method Economic Order Quantity To Reach Efficiency Total Costs Of Raw Material In Pr. Sukun

    Wiwik Sudarwati

    2017-07-01

    Full Text Available The raw material inventory control system determines and guarantees the availability of raw material stock in the right quantity quality and timing. The problem in this research is the procurement of raw materials of tobacco. PR. Sukun still often experiences the excess. This is related to the frequency of raw material purchases and the quantity of raw material purchases which can lead to waste of working capital embedded in raw material inventory raw material ordering costs and raw material storage costs. The purpose of this research is to know how to make an efficiency level in procurement of raw material inventory between EOQ method compared with policy of PR. Sukun. The type of research used is analytic descriptive type. Data analysis begins by analyzing raw material quantity comparison total raw material inventory cost and raw material cost between PR Sukun policy with EOQ method. Based on the results of research known that by using EOQ method can be much more efficient compared to policy of PR. Sukun. The quantity and frequency of purchasing raw materials is less but still take into account the safety stock and reorder point so the production process is not disturbed. In addition the cost of purchasing ordering costs and raw materials storage costs less so as to create efficiencies on the cost of raw materials inventory. PR. Sukun in the procurement of raw material inventory should use EOQ method to be more efficient and take into account the safety stock and reorder point to avoid the inventory excess of raw materials.

  11. Cryoforming evaluation using high-purity nickel

    Lord, D.E.; Meisner, L.F.

    1976-01-01

    The cryogenic forming process was evaluated using nickel 270 to see if it had significant advantages over room-temperature (RT) forming. Typically, the procedure involved fast-strain-rate forming a set of nickel samples at cryogenic temperatures and another set at RT. Both sets were measured at RT for failure strength and their strength-preparation elongation curves compared at equal strains. Two more sets were formed, this time at slow strain rates (one at cryogenic temperatures, the other at RT). Both sets were measured at RT for failure strength and their strength-preparation elongation curves of these sets compared with the previous two at equal temperatures and strains. Cryoforming produced a 30 percent higher-strength nickel than that produced at room temperature at equal strains and strain rates. Forming rate effects disappeared as working temperature decreased. Rate-insensitive cryoforming produced a considerably stronger room-temperature material than room-temperature forming at high strain rates. Transmission electron microscopy indicated apparent structural differences between cryoformed and room-temperature-formed nickel. 14 fig

  12. Sorption techniques for production of high purity refractory metals

    Shatalov, V.V.; Peganov, V.A.; Logvinenko, I.A.; Molchanova, T.V.

    2004-01-01

    A consideration is given to potentialities of sorption processes tot provide a high quality of refractory metal and their alloys when using hydrometallurgical methods for raw material processing. The efficiency of application of ion exchange technology is shown for complex solutions reprocessing for various types of polymetallic raw materials, among them uranium ores, enriched concentrates of refractory metal ores, intermediate products, waste solutions. Based on investigation results on the behaviour of elements in process solutions and the mechanism of their sorption and elution, the process of pure chemical compounds production are developed which provide thereafter manufacturing compact metals. The flowsheets developed are mastered on a commercial scale [ru

  13. Identification of Particles in Parenteral Drug Raw Materials.

    Lee, Kathryn; Lankers, Markus; Valet, Oliver

    2018-04-18

    Particles in drug products are not good and are therefore regulated. These particles can come from the very beginning of the manufacturing process, from the raw materials. To prevent particles, it is important to understand what they are and where they come from so the raw material quality, processing, and shipping can be improved. Thus, it is important to correctly identify particles seen in raw materials. Raw materials need to be of a certain quality with respect to physical and chemical composition, and need to have no contaminants in the form of particles which could contaminate the product or indicate the raw materials are not pure enough to make a good quality product. Particles are often seen when handling raw materials due to color, size, or shape characteristics different from those in the raw materials. Particles may appear to the eye to be very different things than they actually are, so microscope, chemical, and elemental analyses are required for accuracy in proper identification. This paper shows how using three different spectroscopy tools correctly and together can be used to identify particles from extrinsic, intrinsic, and inherent particles. Sources of materials can be humans and the environment (extrinsic), from within the process (intrinsic), and part of the formulation (inherent). Microscope versions of Raman spectroscopy, laser-induced breakdown spectroscopy (LIBS), and IR spectroscopy are excellent tools for identifying particles because they are fast and accurate techniques needing minimal sample preparation that can provide chemical composition as well as images that can be used for identification. The micro analysis capabilities allow for easy analysis of different portions of samples so multiple components can be identified and sample preparation can be reduced. Using just one of these techniques may not be sufficient to give adequate identification results so that the source of contamination can be adequately identified. The

  14. Thermocurrent dosimetry with high purity aluminum oxide

    Fullerton, G.D.; Cameron, J.R.; Moran, P.R.

    1976-01-01

    The application of thermocurrent (TC) to ionizing radiation dosimetry was studied. It was shown that TC in alumina (Al 2 O 3 ) has properties that are suited to personnel dosimetry and environmental monitoring. TC dosimeters were made from thin disks of alumina. Aluminum electrodes were evaporated on each side: on one face a high voltage electrode and on the opposite face a measuring electrode encircled by a guard ring. Exposure to ionizing radiation resulted in stored electrons and holes in metastable trapping sites. The signal was read-out by heating the dosimeter with a voltage source and picnometer connected in series between the opposite electrodes. The thermally remobilized charge caused a transient TC. The thermogram, TC versus time or temperature, is similar to a TL glow curve. Either the peak current or the integrated current is a measure of absorbed dose. Six grades of alumina were studied from a total of four commercial suppliers. All six materials displayed radiation induced TC signals. Sapphire of uv-grade quality from the Adolf Meller Co. (AM) had the best dosimetry properties of those investigated. Sources of interference were studied. Thermal fading, residual signal and radiation damage do not limit TC dosimetry. Ultraviolet light can induce a TC response but it is readily excluded with uv-opaque cladding. Improper surface preparation prior to electrode evaporation was shown to cause interference. A spurious TC signal resulted from polarization of surface contaminants. Spurious TC was reduced by improved cleaning prior to electrode application. Polished surfaces resulted in blocking electrodes and caused a sensitivity shift due to radiation induced thermally activated polarization. This was not observed with rough cut surfaces

  15. Manufacture of high purity metal fluorides

    Vance, J.M.

    1984-01-01

    The Oak Ridge Gaseous Diffusion Plant has been developing technologies of many kinds since the early forties. The primary purpose of this R and D was to reduce the amount of electrical power and capital expense associated with the enrichment of uranium in the 235 isotope. One area that has received a lot of attention is the chemistry of fluorine and metal fluorides. The producing facility at ORGDP is a chemical pilot plant which has been used through the years to demonstrate new processes. Presently existing in this facility are: absorption columns which have been used to remove trace quantities of krypton and oxides of nitrogen and sulfur from gas streams; a flame reactor that is being used to reduce isotopically altered sulfur hexafluoride for conversion to SO 2 which will be used in acid rain studies; an environmental hold system in which methods were developed to remove or neutralize environmental insulting compounds; a fluid bed reactor, and of course the tungsten hexafluoride process. A rhenium hexafluoride facility is also located in the pilot plant. It is basically the same as the tungsten line with three small muffles being used in place of the large WF6 reactor. The product from each process is heated and transferred to approved 5-inch shipping cylinders and transported to the analytical chemistry laboratory for sampling and analysis. These cylinders must be used for shipment and may require modification of the customer facility to accommodate them. Liquid samples are obtained from the product cylinders and a visual examination of the samples for color and melting temperature provides a good indication of the conversion. X-ray fluorescence is utilized to determine the amount of tungsten and the percent conversion to the hexafluoride is calculated from the weighed sample. Infrared in addition to mass spectrometer analyses are performed to verify the findings. The material is then analyzed by spectrographic methods for contaminants

  16. Thermocurrent dosimetry with high purity aluminum oxide

    Fullerton, G.D.; Cameron, J.R.; Moran, P.R.

    1976-01-01

    The application of thermocurrent (TC) to ionizing radiation dosimetry was studied. It was shown that TC in alumina (Al/sub 2/O/sub 3/) has properties that are suited to personnel dosimetry and environmental monitoring. TC dosimeters were made from thin disks of alumina. Aluminum electrodes were evaporated on each side: on one face a high voltage electrode and on the opposite face a measuring electrode encircled by a guard ring. Exposure to ionizing radiation resulted in stored electrons and holes in metastable trapping sites. The signal was read-out by heating the dosimeter with a voltage source and picnometer connected in series between the opposite electrodes. The thermally remobilized charge caused a transient TC. The thermogram, TC versus time or temperature, is similar to a TL glow curve. Either the peak current or the integrated current is a measure of absorbed dose. Six grades of alumina were studied from a total of four commercial suppliers. All six materials displayed radiation induced TC signals. Sapphire of uv-grade quality from the Adolf Meller Co. (AM) had the best dosimetry properties of those investigated. Sources of interference were studied. Thermal fading, residual signal and radiation damage do not limit TC dosimetry. Ultraviolet light can induce a TC response but it is readily excluded with uv-opaque cladding. Improper surface preparation prior to electrode evaporation was shown to cause interference. A spurious TC signal resulted from polarization of surface contaminants. Spurious TC was reduced by improved cleaning prior to electrode application. Polished surfaces resulted in blocking electrodes and caused a sensitivity shift due to radiation induced thermally activated polarization. This was not observed with rough cut surfaces.

  17. Use of alternative raw materials for yoghurt production | Farinde ...

    Soymilk and maize steep water were used as alternative raw materials to cow milk and commercial starter, respectively, for production of yoghurt. The cow milk used was both Fresh milk and dried powdered milk (DANO). The cost of production of the yoghurt samples as well as their chemical, microbial and organoleptic ...

  18. Mineralogy And Raw Material Characterization Of Esie Stone ...

    Electronprobe mineral data of samples of Esie statues is presented as a possible tool for provenance studies. Most of the samples contain talc, chlorite, cummingtonite and rarely tremolite. Other talc-bearing schists are prevalent in the Esie area. However talc-cummingtonite rocks, similar to the raw materials used for the ...

  19. Use of a new borate raw material for glaze formulation

    Gomez-Tena, M. P.; Moreno, A.; Bou, E.; Cook, S.; Galindo, M.

    2010-01-01

    The Rio Tinto Minerals company has developed a new borate (E-4972), which can be used in glaze formulation (patent WO 2007/148101). This new borate, synthesised by low-temperature calcination, fundamentally contributes five oxides: silicon oxide (SiO 2 ), aluminium oxide (Al 2 O 3 ), boron oxide (B 2 O 3 ), calcium oxide (CaO), and sodium oxide (Na 2 O), its content in B 2 O 3 being between 10 and 11% by weight. It is largely amorphous, and quartz is the major crystalline phase present. The characteristics of this new borate, such as its low solubility and ability readily to form glassy phase, enable it to be used as a raw material in glaze compositions. Its suitability for glaze formulation has been the result of several years research in collaboration with the Instituto de Tecnologia Ceramica. In this paper, the feasibility has been studied of fabricating ceramic glazes by using a new synthetic borate raw material that contributes boron to the glaze composition without this needing to be done in fritted form. It has been possible to obtain fired glazes with similar technical and aesthetics characteristics to those obtained from industrial glaze compositions that contain typical frits in their compositions, thus enabling glazes to be formulated by using the new synthetic boron raw material. The results obtained show that this new raw material (E-4972) is particularly appropriate for use in producing glazes with low gloss at high temperature. (Author) 15 refs.

  20. Construction raw materials policy and supply practices in Northwestern Europe

    Meulen, M.J. van der; Koopmans, T.P.F.; Pietersen, H.S.

    2003-01-01

    The present contribution is an inventory of the construction raw materials policy and supply practices in The Netherlands, Belgium, North Rhine-Westphalia, Lower Saxony, Great Britain, Norway and Denmark. The work has been commissioned by the Dutch government in order to benchmark its domestic

  1. Decontamination of drug vegetative raw material by relativistic electron beam

    Gorbanyuk, A.G.; Dikiy, I.L.; Yegorov, A.M.; Linnik, A.F.; Uskov, V.V.

    2004-01-01

    The new technology of decontamination of drug vegetative raw material and medical products is proposed. Advantages of use of relativistic beams in a range of electron energies from 0.5 MeV to 5 MeV for these purposes are shown in comparison with X-radiation of energy from 80 keV to 1 MeV

  2. Effect of phosphorus on hot ductility of high purity iron

    Abiko, K.; Liu, C.M.; Ichikawa, M..; Suenaga, H.; Tanino, M.

    1995-01-01

    Tensile tests on high purity Fe-P alloys with 0, 0.05 and 0.1 mass%P were carried out at temperatures between 300 K and 1073 K to clarify the intrinsic effect of phosphorus on the mechanical properties of iron at elevated temperatures. Microstructures of as-quenched, interrupted and ruptured specimens were observed. Experimental results show that the addition of phosphorus causes a remarkable increase in proof stress of high purity iron at 300 K, but the increase in proof stress by phosphorus decreases with increasing test temperature. The strengthening effect of phosphorus reduces to zero at 1073 K. High purity iron and Fe-P alloys rupture at almost 100% reduction in area at the whole test temperatures. However, Fe-P alloys show much larger elongation at test temperatures above 773 K than high purity iron. The increased elongation of high purity iron by addition of phosphorus was shown to be related to the effect of phosphorus on dynamic recovery and recrystallization of iron as its intrinsic effect. (orig.)

  3. Comparison of Biochars Characteristics from Different Raw Materials

    SUN Tao; ZHU Xin-ping; LI Dian-peng; GU Zhu-yu; ZHANG Jia-xi; JIA Hong-tao

    2017-01-01

    Biochar is the carbon-rich product from biomass under limited supply of oxygen. Biochar has been well recognized in enhancing terrestrial carbon sequestration and greenhouse gas mitigation as well as in improving soil fertility and plant productivity. To explore the differences of biochars produced from different raw materials, six biochar samples made from alfalfa straw, wheat straw, cotton straw, grape vines, sludge and lignite were selected as test material. Qualitative and quantitative an...

  4. Determination of contaminators in high purity lead oxide

    Bellavigna, H.J.; Farias de Funes, S.; Garavaglia, R.N.

    1990-01-01

    Litharge (PbO) is one of the raw materials used in glass fabrication for shielding and cathodic ray tubes employed in measurement instruments; some elements such as silver, chromium, arsenic, bismuth, etc. may confer to the mentioned glasses different unwanted tones which cause image distortion. Emission spectroscopy with photographic detection gives a quick, effective and economical alternative to determine these impurities. (Author) [es

  5. Material Classification Using Raw Time-of-Flight Measurements

    Su, Shuochen

    2016-12-13

    We propose a material classification method using raw time-of-flight (ToF) measurements. ToF cameras capture the correlation between a reference signal and the temporal response of material to incident illumination. Such measurements encode unique signatures of the material, i.e. the degree of subsurface scattering inside a volume. Subsequently, it offers an orthogonal domain of feature representation compared to conventional spatial and angular reflectance-based approaches. We demonstrate the effectiveness, robustness, and efficiency of our method through experiments and comparisons of real-world materials.

  6. 1996 Activities report on energies and raw materials

    1996-01-01

    The 1996 activity survey of the French General Directory for Energy and Raw Materials, which main objectives are to preserve the competitiveness of French economy, enhance environmental protection, secure the long term supply safety and maintain the public service basis for energy supply, is presented. The main themes of the survey are: the nuclear safety in Eastern Europe, the electric power inland market, the evolution of the oil market in 1996, the situation of refining in France, restructuring the BRGM (Mining and Geological Research Bureau), followed by brief facts concerning the sustainable energy development, nuclear energy, electric power, electricity and gas common issues, gas, coal, petroleum products, raw materials and underground materials. A series of global diagrams concludes the survey

  7. Radiation sterilization of some cosmetic raw materials and preparations

    Achmatowicz-Szmajke, T.; Bryl-Sandelewska, T.; Galazka, M.

    1979-01-01

    The problem of microbiological purity of cosmetic preparations is discussed. Some results obtained on the influence of ionizing radiation on organoleptic and physicochemical properties of some cosmetic raw materials and final products are reported. The samples of raw materials and the final products were irradiated with a 10 MeV electron beam from an LAE 13/9 linear accelerator located in INR. The doses delivered to the materials were 0.5 - 2.3 Mrad (5-23 kGy). Immediately after irradiation, organoleptic estimations were made and over the next few days physicochemical investigations were performed. Non-irradiated samples were investigated together with irradiated ones. (T.I.)

  8. Characterisation of two AGATA asymmetric high purity germanium capsules

    Colosimo, S.J.; Moon, S.; Boston, A.J.; Boston, H.C.; Cresswell, J.R.; Harkness-Brennan, L.; Judson, D.S.; Lazarus, I.H.; Nolan, P.J.; Simpson, J.; Unsworth, C.

    2015-01-01

    The AGATA spectrometer is an array of highly segmented high purity germanium detectors. The spectrometer uses pulse shape analysis in order to track Compton scattered γ-rays to increase the efficiency of nuclear spectroscopy studies. The characterisation of two high purity germanium detector capsules for AGATA of the same A-type has been performed at the University of Liverpool. This work will examine the uniformity of performance of the two capsules, including a comparison of the resolution and efficiency as well as a study of charge collection. The performance of the capsules shows good agreement, which is essential for the efficient operation of the γ-ray tracking array

  9. Characterisation of two AGATA asymmetric high purity germanium capsules

    Colosimo, S.J., E-mail: sjc@ns.ph.liv.ac.uk [Department of Physics, Oliver Lodge Laboratory, University of Liverpool, Liverpool L69 7ZE (United Kingdom); Moon, S.; Boston, A.J.; Boston, H.C.; Cresswell, J.R.; Harkness-Brennan, L.; Judson, D.S. [Department of Physics, Oliver Lodge Laboratory, University of Liverpool, Liverpool L69 7ZE (United Kingdom); Lazarus, I.H. [STFC Daresbury, Daresbury, Warrington WA4 4AD (United Kingdom); Nolan, P.J. [Department of Physics, Oliver Lodge Laboratory, University of Liverpool, Liverpool L69 7ZE (United Kingdom); Simpson, J. [STFC Daresbury, Daresbury, Warrington WA4 4AD (United Kingdom); Unsworth, C. [Department of Physics, Oliver Lodge Laboratory, University of Liverpool, Liverpool L69 7ZE (United Kingdom)

    2015-02-11

    The AGATA spectrometer is an array of highly segmented high purity germanium detectors. The spectrometer uses pulse shape analysis in order to track Compton scattered γ-rays to increase the efficiency of nuclear spectroscopy studies. The characterisation of two high purity germanium detector capsules for AGATA of the same A-type has been performed at the University of Liverpool. This work will examine the uniformity of performance of the two capsules, including a comparison of the resolution and efficiency as well as a study of charge collection. The performance of the capsules shows good agreement, which is essential for the efficient operation of the γ-ray tracking array.

  10. High-purity aluminium creep under high hydrostatic pressure

    Zajtsev, V.I.; Lyafer, E.I.; Tokij, V.V.

    1977-01-01

    The effect of the hydrostatic pressure on the rate of steady-state creep of high-purity aluminium was investigated. It is shown that the hydrostatic pressure inhibits the creep. The activation volume of the creep is independent of the direction in the range of (4.7-6.2) kg/mm 2 and of the pressure in the range of (1-7.8000) atm. It is concluded that self-diffusion does not control the creep of high-purity aluminium at room temperature in the investigated stress and pressure range

  11. Mesta/Kenaf as raw material for Kraft pulping

    Saraf, V. P.; Shiveshwar, R. M.; Meshramkar, P. M.; Deb, U. K.; Jaspal, N. S.; Biyani, B. P.

    1980-03-15

    In recent years, the shortage of conventional raw materials for pulping has intensified a world-wide search for alternate raw materials. Among other cellulosic materials, attention has focused on agricultural residues and annual plants. In this category, Kenaf, also called Mesta, has been studied as a fiber source in many countries including the USA, Phillippines and India. A comprehensive study on kraft pulping of mesta was carried out where the fiber morphology, pulping, bleaching and papermaking characteristics were investigated. Black liquor properties were also determined. The results of this study are reported and compared to the conventional raw material bamboo. The investigation has shown that mesta is easily pulped and bleached and forms sheets of excellent strength properties, comparable to or better than bamboo pulps. The black liquor from mesta is similar to bamboo in calorific value but is very low in silica, which is highly desirable from the chemical recovery point of view. As with all agricultural residues and annual plants, mesta has a high bulk per unit weight. The problems arising from this, e.g., baling, transportation, proper utilization of digester capacity, have to be studied before mesta can be widely accepted in the paper industry.

  12. A green preparation of Mn-based product with high purity from low-grade rhodochrosite

    Lian, F.; Ma, L.; Chenli, Z.; Mao, L.

    2018-01-01

    The low-grade rhodochrosite, the main resources for exploitation and applications in China, contains multiple elements such as iron, silicon, calcium and magnesium. So the conventional preparation of manganese sulphate and manganese oxide with high purity from electrolytic product is characterized by long production-cycle, high-resource input and high-pollution discharge. In our work, a sustainable preparation approach of high pure MnSO4 solution and Mn3O4 was studied by employing low-grade rhodochrosite (13.86%) as raw material. The repeated leaching of rhodochrosite with sulphuric acid was proposed in view of the same ion effect, in order to improve the solubility of Mn2+ and inhibit the dissolution of the impurities Ca2+ and Mg2+. With the aid of theoretical calculation, BaF2 was chosen to remove Ca2+ and Mg2+ completely in the process of purifying. The results showed that the impurities such as Ca2+, Mg2+, Na+ were decreased to less than 20ppm, and the Ni- and Fe- impurities were decreased to less than 1ppm, which meets the standards of high pure reagent for energy and electronic materials. The extraction ratio and the recovery ratio of manganese reached 94.3% and 92.7%, respectively. Moreover, the high pure Mn3O4 was one-step synthesized via the oxidation of MnSO4 solution with the ratios of OH-/Mn2+=2 and Mn2+/H2O2=1.03, and the recovery rate of manganese reaches 99%.

  13. Buildings materials and raw materials as a source of exposition of population of the Slovak Republic

    Cabanekova, H.

    2005-01-01

    In this presentation author presents specific activities of potassium-40, radium-226, thorium-232 and equivalent of specific activity in some building materials and raw materials used at building-up of flats in the Slovak Republic

  14. Agaves as a raw material: recent technologies and applications.

    Narváez-Zapata, J A; Sánchez-Teyer, L F

    2009-01-01

    Agave plants are a valuable source of raw material due to its fibrous and complex sugar content of their leaves and core, and their bagasse waste can be use for several aims. This plant genus belongs to the Agavaceae family and until now more than 200 species have been described. A large number of Agave species are currently used as raw material in several biotechnological processes. This review shows the reported applications and patents on fields like alcoholic brewages with special reference to Tequila and Mezcal, the isolation and use of compounds such as saponins and agave fructans, and their potential biotechnological application on several human demands. The process to obtain fibers and cellulose, stock feeds, and several miscellaneous extractives are also reviewed. Some possibilities and problems of cultivation are discussed.

  15. Gas condensate--raw material for producing liquid paraffin hydrocarbons

    Aliyeva, R.B.; Alikishi-Zade, G.Yu.; Kuliyev, A.M.; Leonidov, A.N.; Pereverzev, A.N.

    1980-01-01

    The problem of efficient utilization of gas condensates as raw material for removal of a valuable product, liquid paraffins, is examined. A classification of gas condensates is given which is used as raw material for removing these hydrocarbons: gas condensate with high content of n-alkanes (25-40 mass percent), with average content (18-25 mass percent), with low content (12-18 mass percent), light weight fractions compositions, which do not contain fractions up to 200/sup 0/, and also, content ofless than 12% n-alkanes. Gas condensate I-III groups are 30% of the total reserve of gas condensate. Liquid paraffins hydrocarbons, produced from fractions of diesel fuel, which has been removed from Shatlyk gas condensate under conditions which simulate virtual processes of caramide deparaffinization meet all requirements without additional refining.

  16. High purity liquid phase epitaxial gallium arsenide nuclear radiation detector

    Alexiev, D.; Butcher, K.S.A.

    1991-11-01

    Surface barrier radiation detector made from high purity liquid phase epitaxial gallium arsenide wafers have been operated as X- and γ-ray detectors at various operating temperatures. Low energy isotopes are resolved including 241 Am at 40 deg C. and the higher gamma energies of 235 U at -80 deg C. 15 refs., 1 tab., 6 figs

  17. Pressure-assisted sintering of high purity barium titanate

    van den Cruijsem, S.; Varst, van der P.G.T.; With, de G.; Bortzmeyer, D.; Boussuge, M.; Chartier, Th.; Hausonne, J.M.; Mocellin, A.; Rousset, A.; Thevenot, F.

    1997-01-01

    The dielectric behaviour of High Purity Barium titanate (HPB) ceramics is strongly dependent on the grain size and porosity. For applications, control of grain size and porosity is required. Pressure-assisted sintering techniques at relatively low temperatures meet these requirements. In this study,

  18. Isolation of high purity americium metal via distillation

    Squires, Leah N.; King, James A.; Fielding, Randall S.; Lessing, Paul

    2018-03-01

    Pure americium metal is a crucial component for the fabrication of transmutation fuels. Unfortunately, americium in pure metal form is not available; however, a number of mixed metals and mixed oxides that include americium are available. In this manuscript a method is described to obtain high purity americium metal from a mixture of americium and neptunium metals with lead impurity via distillation.

  19. MICROBIOLOGY OF RAW MATERIALS USED FOR CONFECTIONARY PRODUCTION

    Jana Petrová

    2015-02-01

    Full Text Available The aim of our study was to evaluate the microbiological quality of raw materials used for preparation of confectionery products. For microbiological evaluation total count of bacteria, mesophilic aerobic bacteria, coliform bacteria, yeast and microscopic filamentous fungi in samples of raw materials used in the manufacture and creams of confectionery products were detected. In addition to these groups of microorganisms the presence of pathogenic microorganisms Salmonella spp. and Staphylococcus aureus in creams was monitored. Products are assessed according to the limit values of the number of microorganisms defined in the Codex Alimentary of the Slovak Republic. For microbiological analysis of confectionery products, sampling of components of confectionary products and cream was carried out according to current health regulations and altogether 65 samples of components and creams were collected: 10 samples of raw materials sugar, 10 samples of flour, 10 samples of butter and 10 samples of eggs, 5 samples of butter yolk from cream-filled disposable bag without rum addition, 5 samples of butter yolk from cream-filled disposable bag with rum addition, 5 samples of cream-filled multiple use paid bag, 5 samples of cream-filled newly purchased paid bag, 5 samples of Venček corpus and 5 samples of the French cubes corpus. From raw material the highest TBC (2.65log CFU was in flour, but the lowest in sugar (1.35 log CFU, the highest years counts was found on flour (2.42, but lowest in butter (1.18, while wasn’t in egg. In samples of creams and corpus were increased occurrence of yeast, coliform bacteria. Salmonella spp. and Staphylococcus aureus weren’t isolated from any tested sample.

  20. Petroleum as a raw material resource for sustainable development

    Egorov, O.I.

    1996-01-01

    Author notes that for economic and social region development it is necessary has been created large petroleum chemical plants near by Atyrau city (initial raw material - Tengiz, Korolev and other petroleum deposits of this region) and Aktau (Mangistau and Bazuchin petroleum). Realization of projects for structure changes of petroleum and gas region demands a great investments. It is noted that growing scales of petroleum and gas resources mastering calls already a considerable environmental complications because of Caspian Sea's level marking rise

  1. Effect of the raw materials processing on their dustiness

    López Lilaoa, A.; Juárezb, M.; Sanfelix Fornera, V.; Mallol Gascha, G.; Monfort Gimeno, E.

    2017-01-01

    During the handling and/or processing of powdered materials in the CERAMICS INDUSTRY, one of the most important risks regarding the environmental and occupational health is the potential generation of dust. In this regard, a parameter of great interest is the dustiness of the processed materials; this parameter quantifies the tendency of the powdered materials to generate dust when handled. In this study, to determine the dustiness of a ceramic raw material composition (mixture of the body raw materials), the continuous drop method has been used. This test apparatus was selected because it is considered to better simulate how ceramic materials are handled in the CERAMICS INDUSTRY. The obtained results show that the dustiness of the same ceramic composition exhibits significant changes during the manufacturing process, depending on the presentation form. In this regard, the dry milling sample presents the highest dustiness, which can be significantly reduced (>75%) applying the the moisturization and agglomeration. The obtained results also shown that the best presentation form, regarding the minimization of the dust generation, is achieved in the spray-drying process, where the dustiness is reduced by 95%. [es

  2. Map of critical raw material deposits in Europe

    Guillaume, Bertrand

    2016-04-01

    Map of critical raw material deposits in Europe Guillaume BERTRAND1, Daniel CASSARD1, Nikolaos ARVANITIDIS2, Gerry STANLEY3 and the EuroGeoSurvey Mineral Resources Expert Group4. 1 - Bureau de Recherches Géologiques et Minières (BRGM), Georesources Divison, 3 avenue Claude Guillemin, 45060 Orléans cedex 2, FRANCE. 2 - Sveriges Geologiska Undersökning (SGU), Box 670, SE-751 28, Uppsala, SWEDEN 3 - Geological Survey of Ireland (GSI), Beggars Bush, Haddington Road, Dublin D04 K7X4, IRELAND 4 - EuroGeoSurveys, Rue Joseph II 36-38, 1000 Brussels, BELGIUM The Critical Raw Material (CRM) Deposit Map of Europe, prepared by EuroGeoSurvey's Mineral Resources Expert Group (MREG), shows European mineral deposits from the ProMine Mineral Deposit database containing critical commodities, according to the 2014 list of critical raw materials of the European Commission. EuroGeoSurveys (EGS), The Geological Surveys of Europe, is a not-for-profit organization representing 37 National Geological Surveys and some regional Geological Surveys in Europe. It provides the European Institutions with expert, independent, balanced and practical pan-European advice and information as an aid to problem-solving, policy development, regulatory and programme formulation in areas such as natural resources, energy and geo-hazards. The EGS MREG is actively involved in contributing to policy and strategy-making processes aimed at identifying, characterizing and safeguarding resource potential, especially for critical raw materials through data provision, research, technological development and innovation. The European Union aspires to reducing the import dependency of raw materials, especially CRM, that are essential to Europe's industries. In this respect, mineral resource information, data sharing and networking by European Geological Surveys is crucial. The Strategic Implementation Plan of the European Innovation Partnership on Raw Materials highlights the need for establishing and maintaining a

  3. Approaches to the accurate characterization of high purity metal fluorides and fluoride glasses

    Beary, E. S.; Paulsen, P. J.; Rains, T. C.; Ewing, K. J.; Jaganathan, J.; Aggarwal, I.

    1990-11-01

    The analytical challenges posed by the measurement of trace contaminants in high purity metal fluorides require that innovative chemical preparation procedures be used to enhance existing instrumental techniques. The instrumental techniques used to analyze these difficult matrices must be sensitive enough to detect extremely low levels of trace impurities, and the background interferences derived from the matrix (metal fluoride or glass) must be minimized. A survey of analytical techniques that have the necessary characteristics to analyze these materials will be given. In addition, means of controlling the chemical blank will be presented. Mass and atomic spectrometric techniques will be discussed, specifically graphite furnace atomic absorption spectrometry (GFAAS) and inductively coupled plasma-mass spectrometry (ICP-MS). Analytical procedures using GFAAS and ICP-MS have been developed to determine sub ppb (part per billion) levels of contaminants in high purity fluoride materials.

  4. Analysis of Mechanical Properties of Fabrics of Different Raw Material

    Aušra ADOMAITIENĖ

    2011-07-01

    Full Text Available The study analyzes dependence of mechanical properties (breaking force, elongation at break, static friction force and static friction coefficient on integrated fabric structure factor j and raw material density r, among the fabrics of different raw material (cotton, wool, polypropylene, polyester and polyacrylnitrile and woven in different conditions. The received results demonstrate that sometimes strong dependences exist (wool, polypropylene and polyacrylnitrile, whereas in some cases (cotton and polyester there is no correlation. It was also discovered that the breaking force and elongation at break in the direction of weft increase, when fabric structure becomes more rigid. In the meantime variations of the curves in the direction of warp are insignificant. Regarding static friction force and static friction coefficient (found in two cases, when fabrics were rubbing against leather and materials, it was discovered that consistency of the curves is irregular, i. e. they either increase or decrease, when integrated fabric structure factor j growth. It was also identified that some dependences are not strong and relationship between explored and analyzed factors does not exist. Variation of all these mechanical properties with respect to material density r enables to conclude that increase of material density r results in poor dependences or they are whatsoever non-existent.http://dx.doi.org/10.5755/j01.ms.17.2.487

  5. Reflections on prospective raw materials and materials with regard to the Czech Republic

    Schejbal, C.; Palas, M.

    1997-01-01

    Reflections on prospective mineral raw materials and materials must rest upon the expected demographic evolution, the evaluation of economic development and the development of manufacturing technologies and materials corresponding to them, trends in the consumption of mineral raw materials and possibilities of securing them. The evaluation of the given factors under conditions of the Czech Republic shows that one of the decisive prerequisites to transforming the Czech economy is to assure the fuel and energy security of the state. In addition to emphasis put on traditional and newly developed technologies of utilization of domestic resources of coal and the development of nuclear power, a diversification of supplies of oil and gas is necessary. Moreover, it is necessary to ensure domestic resources of raw materials to some prospective material areas, or to provide these raw materials by means of imports and/or entrepreneurial activity abroad. As far as raw materials for building and industrial rocks are concerned, it is necessary to support the exploitation and home utilization through laws and suitable economic tools at respecting environmental limitations. With non-traditional prospective raw materials, it will be desirable to promote exploration and mining especially in those cases when a precondition exists for the securing of sufficient reserves or when reserves are already known

  6. Investigations of radioactivity of building raw and materials

    Zak, A.; Biernacka, M.; Jagielak, J.; Lipinski, P.

    1993-01-01

    In 1980, Ministry of Building and Building Materials Industry, the Central Laboratory for Radiological Protection (abbreviated as CLRP), Ministry of Health and Social Welfare have agreed to issue the compulsory regulation of performing the validation of investigations of building raw and materials. Methods of measurement, apparatus and method of evaluation of results of the investigations have been recommended for the whole country. The following two criteria of usefulness of a building material for housing and public building have been accepted, f 1 = 0.00027 S K + 0.0027 S Ra0 .0043 S Th ≤ 1 (this one limit exposition of the whole body to gamma radiation); f 2 = S Ra ≤ 185 Bq/kg (this one limits exposition of lung epithelium to progeny of radon 222 Rn exhaled from the building walls). The CLRP and Institute of Building Technology supervise over correctness (agreement with the regulations) of operation of laboratories in Departments of Building Industry and Energy, organize training of the personnel and collect results of the measurements. From 1980 till 1991, results of measurements of 6550 samples from 550 localities were collected in computer data base organized in CLRP. In this paper, results of examination of selected groups of building raw and materials have been presented. Annual average values of the qualification coefficients f 1 and f 2 have been also analyzed. (author). 7 refs, 13 figs, 2 tabs

  7. Event timing in high purity germanium coaxial detectors

    El-Ibiary, M.Y.

    1979-08-01

    The timing of gamma ray radiation in systems using high purity coaxial germanium detectors is analyzed and compared to that of systems using Ge(Li) detectors. The analysis takes into account the effect of the residual impurities on the electric field distribution, and hence on the rate of rise of the electrical pulses delivered to the timing module. Conditions under which the electric field distribution could lead to an improvement in timing performance, are identified. The results of the analysis confirm the experimental results published elsewhere and when compared with those for Ge(Li) detectors, which usually operate under conditions of charge carrier velocity saturation, confirm that high purity germanium detectors need not have inferior timing characteristics. A chart is given to provide a quantitative basis on which the trade off between the radius of the detector and its time resolution may be made

  8. Hydrogen concentration and distribution in high-purity germanium crystals

    Hansen, W.L.; Haller, E.E.; Luke, P.N.

    1981-10-01

    High-purity germanium crystals used for making nuclear radiation detectors are usually grown in a hydrogen ambient from a melt contained in a high-purity silica crucible. The benefits and problems encountered in using a hydrogen ambient are reviewed. A hydrogen concentration of about 2 x 10 15 cm -3 has been determined by growing crystals in hydrogen spiked with tritium and counting the tritium β-decays in detectors made from these crystals. Annealing studies show that the hydrogen is strongly bound, either to defects or as H 2 with a dissociation energy > 3 eV. This is lowered to 1.8 eV when copper is present. Etching defects in dislocation-free crystals grown in hydrogen have been found by etch stripping to have a density of about 1 x 10 7 cm -3 and are estimated to contain 10 8 H atoms each

  9. Recovery of high-purity hydrogen from COG

    Tsukiyama, Y

    1982-01-01

    A general account of the latest trends in the recovery of high-purity hydrogen from coke oven gas (COG), the article being based on both Japanese and overseas literature: 1) Deep-freeze separation: impurities are liquefied and removed. This method make use of the fact that hydrogen is hard to liquefy. 2) The PSA method: high-purity hydrogen is recovered by the adsorption of other constituents at high pressures. This technique makes use of the fact that the adsorption capacity of an adsorbent varies with the partial pressure of the substances being adsorbed. 3) Membrane separation: a permeation separation method that uses a functional polymer separation membrane, and that depends on the fact that hydrogen has a low molecular weight in comparison with the other constituents. (19 refs.) (In Japanese)

  10. Insulating materials from renewable raw materials. 4. ed.; Daemmstoffe aus nachwachsenden Rohstoffen

    Brandhorst, Joerg; Spritzendorfer, Josef; Gildhorn, Kai; Hemp, Markus

    2012-03-27

    The thermal insulation has become a central issue in the construction and renovation of buildings. The question of healthy building materials and appropriate construction follows the desire of a comfartable and allergy-free living. Due to these developments, insulation materials from renewable resources increasingly has raised the consciousness. The brochure under consideration describes the dynamic market of insulation materials consisting of renewable raw materials. Wood fibers, wood wool, sheep wool, flax, hemp, reeds, meadow grass, cork, cellulose, seaweed and bulrushes are considered as renewable raw materials for insulating materials.

  11. System simulation application for determining the size of daily raw material purchases at PT XY

    Napitupulu, H. L.

    2018-02-01

    Every manufacturing company needs to implement green production, including PT XY as a marine catchment processing industry in Sumatera Utara Province. The company is engaged in the processing of squid for export purposes. The company’s problem relates to the absence of a decision on the daily purchase amount of the squid. The purchase of daily raw materials in varying quantities has caused companies to face the problem of excess raw materials or otherwise the lack of raw materials. The low purchase of raw materials will result in reduced productivity, while large purchases will lead to increased cooling costs for storage of excess raw materials, as well as possible loss of damage raw material. Therefore it is necessary to determine the optimal amount of raw material purchases every day. This can be determined by applying simulation. Application of system simulations can provide the expected optimal amount of raw material purchases.

  12. Renewable raw materials in the field of industry; Nachwachsende Rohstoffe in der Industrie

    Peters, D.

    2006-07-01

    Being used to the practiced processing of raw materials for many decades the industry had to tap the advantage of renewable raw materials again. Conventional processing methods had to be changed and to be newly developed. This has been a rewarding task considering the ecological advantages but also considering the interesting markets for products based upon renewable raw materials. Today the German industry above all the chemical industry again processes agricultural and forestal raw materials to a considerable extent. Ten percent of the raw materials processed by the chemical industry are renewable. The wood processing industry is an important economic sector that achieves a value creation with the raw material wood exceeding the value creation of other industries by far. This brochure gives an overview of the possible substances, which are processed from renewable raw materials in Germany and it shows the important role that agricultural raw materials and wood already play for the industry nowadays. (orig.)

  13. Demands made on high-purity copper for special purposes

    Roettges, D.

    1977-01-01

    The properties (electrical resistivity, residual impurities) of high-purity copper produced on a technical scale are reported as well as its practical applications. The paper discusses a high-oxygen copper (SV) with low residual resistivity at low temperatures and an oxygen-free (hydrogen-stable) copper (BE electronic) with low gas content. The SV quality has been specially developed for use as stabilizer in superconductors while the BE quality is used in high and ultrahigh vacuum. (GSC) [de

  14. Method of thermal reprocessing of hydrocarbon raw material

    Feygin, Ye.A.; Bakhshiyan, Ts.A.; Barashkov, R.Ya.; Kazhdan, A.Z.; Raud, E.A.; Umanchik, N.P.

    1979-09-30

    In the method of thermal reprocessing of hydrocarbon raw material, to raise the efficiency of the process the heat exchange is done using a heat carrier in the form of a melt of metals or their salts, circulating in a closed system with a forced heating source in sequence through the pyrolysis zone, cooling zone, and heating zone. For example, the benzine fraction with initial boiling temperatures of 80-186 degrees C, together with steam, in the amount of 20% at 20 degrees C and pressure of 2 atmospheres, goes to the heating zone. Liquid Li goes there from the cooling zone through a closed circuit at 749 degrees C. The benzine, evaporated and heated to 300 degrees C, together with the melt, go to the pyrolysis zone, where the benzine is heated through the wall by the liquid Li coming from the heat carrier heating zone at 1000 degrees C. From the pyrolysis zone, the products, containing 41% C/sub 2/H/sub 4/, 15% C/sub 3/H/sub 6/ and 21% heavy fractions, go with the melt at 900 degrees C to the cooling zone, where they are cooled through the wall to 400 degrees C by the circulating liquid Li. The Li temperature at the entry into the cooling zone is 350 degrees C. The degree of raw material conversion is over 98%; the melt/raw material weight ratio is 0.2. Using this method enables a reduction in the pyrolysis zone from 80 to 8 m and the cooling zone area from 13 to 0.6 m/sup 2/ compared with the existing one, and transition from a multiple-tube cooling zone design to a tube one. The volume of the furnace unit is reduced from 500 to 10 m/sup 3/; the C/sub 2/H/sub 4/ yield is increased from 26-28 to 40-42%.

  15. Surface passivation of high purity granular metals: zinc, cadmium, lead

    Pirozhenko L. A.

    2017-10-01

    Full Text Available For the high purity metals (99.9999%, such as zinc, cadmium, and lead, which are widely used as initial components in growing semiconductor and scintillation crystals (CdTe, CdZnTe, ZnSe, (Cd, Zn, Pb WO4, (Cd, Zn, Pb MoO4 et al., it is very important to ensure reliable protection of the surface from oxidation and adsorption of impurities from the atmosphere. The specific features of surface passivation of high purity cadmium, lead and zinc are not sufficiently studied and require specific methodologies for further studies. The use of organic solutions in the schemes of chemical passivation of the investigated metals avoids hydrolysis of the obtained protective films. The use of organic solvents with pure cation and anion composition as the washing liquid prevents chemisorption of ions present in the conventionally used distilled water. This keeps the original purity of the granular metals. Novel compositions of etchants and etching scheme providing simultaneous polishing and passivation of high purity granular Zn, Cd and Pb are developed. Chemical passivation allows storing metals in the normal atmospheric conditions for more than half a year for Zn and Cd and up to 30 days for Pb without changing the state of the surface. The use of the glycerol-DMF solution in the processes for obtaining Pb granules provides self-passivation of metal surfaces and eliminates the additional chemical processing while maintaining the quality of corrosion protection.

  16. Effects of gamma irradiation on raw materials and perfumes

    Guillot, M.; Pelpel, A.

    1983-01-01

    In order to enlight the strange problem of apparent perfume stability observed in manufactured talc powders sterilized by gamma rays, investigations were made on samples of odorant substances (raw materials, essential oils, or elaborated mixtures). As a rule, no immediate adulteration of olfactive caracteristics resulted at once from gamma irradiation. In several cases, a stabilizing effect appeared immediately and remained effective after long storage in various conditions (of temperature, or light, or oxygen exposure). This unexpected effect seems to be in accordance with previous experiments on gamma or electron irradiations of mixtures of organic molecules, reported in litterature: a mutual inhibition was observed to take place [fr

  17. Time influence in chemical treatment of Brazilian raw materials type

    Argolo, F.; Dias, C.; Machado, A.; Volzone, C.; Ortiga, J.; Valenzuela Diaz, F.

    2012-01-01

    Clays are part of raw materials in different industries. The mineralogical composition and purity greatly influence the application thereof. Chemical treatments applied, such as acid attack, modify their properties and thus their possible uses. Taking in to account that, clay minerals, may differ by more or less resistance to chemical attacks, two types of clay were studied with different mineralogical composition to assess the degree of resistance to chemical attack treatment such as acid. Acid treatments that were applied, differ mainly in the contact time between the solid and the liquid. The solids were studied by X-ray diffraction analysis, chemical analysis and infrared analysis

  18. The technological raw material heating furnaces operation efficiency improving issue

    Paramonov, A. M.

    2017-08-01

    The issue of fuel oil applying efficiency improving in the technological raw material heating furnaces by means of its combustion intensification is considered in the paper. The technical and economic optimization problem of the fuel oil heating before combustion is solved. The fuel oil heating optimal temperature defining method and algorithm analytically considering the correlation of thermal, operating parameters and discounted costs for the heating furnace were developed. The obtained optimization functionality provides the heating furnace appropriate thermal indices achievement at minimum discounted costs. The carried out research results prove the expediency of the proposed solutions using.

  19. Analytical techniques for characterization of raw materials in cell culture media

    Sharma Chandana

    2011-11-01

    Full Text Available Abstract Raw materials are a critical part of any cell culture medium; therefore, it is of utmost importance to understand and characterize them for high-quality product. The raw material characterization (RMC program at SAFC focuses on individual screening of raw materials both analytically and biologically. The goal of the program is to develop the best-in-class knowledge base of the raw materials used in SAFC’s media formulations and their impact on performance of products.

  20. The Hydrometallurgical Extraction and Recovery of High-Purity Silver

    Hoffmann, James E.

    2012-06-01

    -bearing inputs, will be described in detail to demonstrate how typical chemical engineering unit process and unit operations have supplanted classic smelting and fire refining techniques. The Kennecott Copper Company, which has operated a hydrometallurgical circuit successfully for the recovery of high-purity silver from the slimes wet chlorination residue, has permitted me to provide some operation information and results using the technology. Both Phelps Dodge and Kennecott should be recognized for their forward-looking attitude in undertaking the conversion of conceptual chemistry into successful, full-scale plants. The process as employed at Phelps Dodge is discussed at length in reference (J.E. Hoffmann and B. Wesstrom: Hydrometallurgy, 1994, vol. 94, pp. 69-105).

  1. Order acceptance in food processing systems with random raw material requirements

    Kilic, Onur A.; van Donk, Dirk Pieter; Wijngaard, Jacob; Tarim, S. Armagan

    This study considers a food production system that processes a single perishable raw material into several products having stochastic demands. In order to process an order, the amount of raw material delivery from storage needs to meet the raw material requirement of the order. However, the amount

  2. Regenerative raw materials - High technology without end; Nachwachsende Rohstoffe - Spitzentechnologie ohne Ende

    Wenig, Barbara

    2007-07-01

    Regenerative raw materials are the basis for a multiplicity of environmentally friendly products. Regenerating raw materials fascinate by special qualities and offer the possibility of preserving only restricted existing fossil resources and climatic friendly managing. The review under consideration reports on areas in which vegetable raw materials already are established as well as on future prospects.

  3. Analytical challenges in characterization of high purity materials

    Unknown

    analysis offers an impressive number of tools to simulta- neously determine a large number of elements and com- ..... introduction equipment. Magnetic sector multicollection detection systems with as many ..... able to fit around the curved focal region of other mass- spectrometer designs. Further, because each detector chip.

  4. Flotation tailings as a raw material for ceramic building materials

    Burmistrov, V N; Karpunina, T I; Smolin, V N

    1986-02-01

    The VNIIstrom research institute developed a method for utilizing flotation tailings for production of bricks. Tailings are dewatered using filter presses. After dewatering, moisture content in the tailings ranges from 25 to 26%. Tailings are mixed with chamotte with a grain size to 2 mm. Using 30% chamotte improves mechanical and physical properties of the bricks and reduces energy consumption of brick firing. Tailings mixed with chamotte are granulated and dried on a conveyor. Granules with moisture content reduced to the optimum level are mixed a second time and formed in a press. The bricks are fired in a tunnel kiln with modified design. The bricks made of flotation tailings mixed with 30% chamotte are characterized by mechanical properties comparable to those of high quality bricks made of conventional materials.

  5. New technologies and raw materials for iron and steel making

    Holappa, L. [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Metallurgy

    1998-07-01

    The current steelmaking is still mainly based on two alternatives routes. The first one is ore based production route via reduction in blast furnaces (BF) to produce carbon-rich hot metal which is then oxidised in basic oxygen converter process (BOF) to crude steel, then refined and alloyed in several secondary (ladle) metallurgical operations to its final composition, further followed by continuous casting and rolling operations. The second main steelmaking route starts from steel scrap as the main raw material, melting of scrap in electric furnaces to crude steel, the subsequent stages being corresponding to those in ore based steelmaking. Both these processes represent well-established and highly developed technologies. However, they have some drawbacks. Blast furnace process needs sinter or pellets and coke as its raw materials. That means erection of large integrates with high investment costs in the production units themselves as well as to avoid severe environmental issues. Scrap-based steelmaking is ideal from the viewpoint of recycling, but it is limited by the scrap availability and quality problems encountered by the noticeable metallic impurities in purchase scrap. Direct reduction of iron ore in solid state to produce direct reduced iron (DRI) has its roots in the early ironmaking history but was firstly commercialised on a modern concept at the end of the 1960's when the first Midrex installation was run into operation. Most of the DR-processes utilise natural gas as the reducing agent but also some processes utilising coal have been introduced and are used in industrial scale. The oil crises in the 1970's slowed down the progress of DRI production but during the last 15 years the production has steadily grown being nowadays about 35 Mton/year. That corresponds to roughly 10 pct of the total solid material input into the world steel production. No doubt, the growth will continue in the near future as well. Quite recently, a new process

  6. From raw material to dish: pasta quality step by step.

    Sicignano, Angelo; Di Monaco, Rossella; Masi, Paolo; Cavella, Silvana

    2015-10-01

    Pasta is a traditional Italian cereal-based food that is popular worldwide because of its convenience, versatility, sensory and nutritional value. The aim of this review is to present a step-by-step guide to facilitate the understanding of the most important events that can affect pasta characteristics, directing the reader to the appropriate production steps. Owing to its unique flavor, color, composition and rheological properties, durum wheat semolina is the best raw material for pasta production. Although pasta is traditionally made from only two ingredients, sensory quality and chemical/physical characteristics of the final product may vary greatly. Starting from the same ingredients, there are a lot of different events in each step of pasta production that can result in the development of varieties of pasta with different characteristics. In particular, numerous studies have demonstrated the importance of temperature and humidity conditions of the pasta drying operation as well as the significance of the choice of raw material and operating conditions on pasta quality. © 2015 Society of Chemical Industry.

  7. Utilization of Delignified Sawdust as Raw Material of Biogas Production

    Zumalla Asfarina

    2018-01-01

    Full Text Available Biogas is one alternative to replace the irreplaceable energy source that has begun to diminish its existence. The raw materials for biogas manufacture are renewable biomass, usually using plantation waste, agriculture, and livestock. Using biogas can also reduce environmental pollution. One of the agricultural waste that has great potential to become the raw material of biogas is teak sawdust. Wood processing industry in Indonesia quite a lot, but wood has a high lignosesluosa content, so it needs the right method to process it. With the delignification of lignin levels on teak sawdust will decrease. Wood sawdust is soaked using NaOH for 1, 2, 3, and 4 days with 4% w / v concentration. The lowest lignin and hemicellulose content was 25.79% and 87.9% in pretreatment for 4 days, while the highest cellulose level was 57, 34%. The accumulated volume of biogas at 1 day pretreatment, ie 709 ml / g TS. Gcms shows the enlarged peak area of methanamine, N-methyl from before pretreatment. The fastest biogas formation (λ in 4 days pretreatment, 1.60403 days and the largest constant A and U variables at 1 day were 914.5903 ml / g TS and 34.59765 ml / g TS.

  8. Characterization of Limestone as Raw Material to Hydrated Lime

    Salem Hwidi, Rajeb; Nuraiti Tengku Izhar, Tengku; Saad, Farah Naemah Mohd

    2018-03-01

    In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.

  9. Radiation decontamination (hygienisation) of cosmetic raw materials and products

    Malec-Czechowska, K.; Migdal, W.; Owczarczyk, H.B.

    1998-01-01

    Microbiological purity of cosmetics is a problem of today because of growing hygienic requirements to these products. The demand for high hygienic purity from one side and the limitation in the use of conservants to cosmetics from the other side stimulate the research activity, the aim of which is to satisfy present requirements in this field. The application of radiation decontamination (hygienisation) seems to be one of solutions. In present report were present the results of the study on the effect of electron beam irradiation on microbial contamination of selected cosmetics and some raw materials used in cosmetic industry. Radiation doses applied were not higher than 6.0 kGy. The level of microbial contamination in both unirradiated and irradiated samples was determined by applying the standard microbiological methods. In addition, the quality and usefulness of irradiated cosmetics were examined by methods used in cosmetic industry. The results obtained show conclusively that radiation treatment can be successfully used for the decontamination (hygienisation) of cosmetics and some raw materials used in their production, without changing the quality and the usefulness of the product released. (author)

  10. Annual report 2001. General direction of energy and raw materials

    2001-01-01

    This report summarizes the 2001 activity of the French general direction of energy and raw materials (DGEMP) of the ministry of finances and industry: 1 - security of energy supplies: a recurrent problem; 2001, a transition year for nuclear energy worldwide; petroleum refining in font of the 2005 dead-line; the OPEC and the upset of the oil market; the pluri-annual planning of power production investments; renewable energies: a reconfirmed priority; 2 - the opening of markets: the opening of French electricity and gas markets; the international development of Electricite de France (EdF) and of Gaz de France (GdF); electricity and gas industries: first branch agreements; 3 - the present-day topics: 2001, the year of objective contracts; AREVA, the future to be prepared; the new IRSN; the agreements on climate and the energy policy; the mastery of domestic energy consumptions; the safety of hydroelectric dams; Technip-Coflexip: the birth of a para-petroleum industry giant; the cleansing of the mining activity in French Guyana; the future of workmen of Lorraine basin coal mines; 4 - 2001 at a glance: highlights; main legislative and regulatory texts; 5 - DGEMP: November 2001 reorganization and new organization chart; energy and raw materials publications; www.industrie.gouv.fr/energie. (J.S.)

  11. Prospects for development of hydrocarbon raw materials resources reproduction

    Vertakova, Y. V.; Babich, T. N.; Polozhentseva, Y. S.; Zvyagintsev, G. L.

    2017-10-01

    The article presents data on the influence of factors in the field of innovative technology of thermocatalytic depolymerization of solid household wastes (SHW) on the efficiency and prospects for the development of technogenic hydrocarbon raw materials resource reproduction. Process thermodynamics, reactions kinetics, the mechanism of thermolysis of secondary polymers in organic solvents have been studied by means of laboratory experiments. It is shown that different morphological groups of wastes dissolve practically at the same rate at temperatures of 250-310°C. A homogeneous product is formed in the liquid phase; the spread of values for the elements lies in the interval of 1.5-4.5 %; technological requirements of the stages of formation of boiler fuels are satisfied. Using the principles of patent analysis, new techniques of processing household waste components are proposed. The basics of energy-efficient and energy-saving processes of technogenic hydrocarbon raw materials resource reproduction have been laid. The possibility of increasing the production payback and intensification is shown. Ecological and demographic safety for population and technical and economic benefits from SHW processing are achieved.

  12. Synthesis of material microporous using raw materials alternative as a source of silica and alumina

    Santos, E.A.; Silva, T.L.

    2014-01-01

    Synthetic zeolites have important properties of a technological viewpoint. Thus, this work aims at the use of natural raw materials such as kaolin waste and wood ash in order to produce these microporous materials. The starting materials were characterized by X-ray diffraction (XRD) and spectroscopy, X-ray fluorescence (XRF); the phases formed as synthesis products were identified by XRD and gravimetric and differential thermal analysis (DTA/TG). Hydrothermal synthesis took place by mixing the raw materials in stoichiometrically calculated batches with NaOH (3M) at 90 °C and time of 6, 20, 24 and 48 hours. The results show the formation of phases of type zeolite A and sodalite, demonstrating the raw materials be an efficient and low cost alternative to producing microporous materials. (author)

  13. Melting behaviour of raw materials and recycled stone wool waste

    Schultz-Falk, Vickie; Agersted, Karsten; Jensen, Peter Arendt

    2018-01-01

    Stone wool is a widely used material for building insulation, to provide thermal comfort along with fire stability and acoustic comfort for all types of buildings. Stone wool waste generated either during production or during renovation or demolition of buildings can be recycled back into the sto...... wool melt production. This study investigates and compares the thermal response and melting behaviour of a conventional stone wool charge and stone wool waste. The study combines differential scanning calorimetry (DSC), hot stage microscopy (HSM) and X-ray diffraction (XRD). DSC reveals...... that the conventional charge and stone wool waste have fundamentally different thermal responses, where the charge experiences gas release, phase transition and melting of the individual raw materials. The stone wool waste experiences glass transition, crystallization and finally melting. Both DSC and HSM measurements...

  14. High purity heavy water production: need for total organic carbon determination in process water streams

    Ayushi; Kumar, Sangita D.; Reddy, A.V.R.; Vithal, G.K.

    2009-01-01

    In recent times, demand for high purity heavy water (99.98% pure) in industries and laboratories has grown by manifold. Its application started in nuclear industry with the design of CANDU reactor, which uses natural uranium as fuel. In this reactor the purest grade of heavy water is used as the moderator and the primary coolant. Diverse industrial applications like fibre optics, medicine, semiconductors etc. use high purity heavy water extensively to achieve better performance of the specific material. In all these applications there is a stringent requirement that the total organic carbon content (TOC) of high purity heavy water should be very low. This is because the presence of TOC can lead to adverse interactions in different applications. To minimize the TOC content in the final product there is a need to monitor and control the TOC content at each and every stage of heavy water production. Hence a simple, rapid and accurate method was developed for the determination of TOC content in process water samples. The paper summarizes the results obtained for the TOC content in the water samples collected from process streams of heavy water production plant. (author)

  15. Insulating materials from renewable raw materials. 3. upd. ed.; Daemmstoffe aus nachwachsenden Rohstoffen

    Brandhorst, Joerg; Spritzendorfer, Josef; Gildhorn, Kai; Hemp, Markus

    2009-07-01

    Due to increasing energy prices, obligations to climatic protection and the desire for comfortable, allergy-free living, the thermal insulation is a central question with building and sanitation. Under this aspect, the contribution under consideration describes the very dynamic market of the insulating materials from renewable raw materials and deals with the questions of the users. In particular, the following raw materials are considered in the production of insulating materials: Wood fibre, wood chips, wood wool, sheep wool, flax, hemp, reeds, straw, cellulose.

  16. Methodology for Evaluating Raw Material Changes to RSRM Elastomeric Insulation Materials

    Mildenhall, Scott D.; McCool, Alex (Technical Monitor)

    2001-01-01

    The Reusable Solid Rocket Motor (RSRM) uses asbestos and silicon dioxide filled acrylonitrile butadiene rubber (AS-NBR) as the primary internal insulation to protect the case from heat. During the course of the RSRM Program, several changes have been made to the raw materials and processing of the AS-NBR elastomeric insulation material. These changes have been primarily caused by raw materials becoming obsolete. In addition, some process changes have been implemented that were deemed necessary to improve the quality and consistency of the AS-NBR insulation material. Each change has been evaluated using unique test efforts customized to determine the potential impacts of the specific raw material or process change. Following the evaluations, the various raw material and process changes were successfully implemented with no detectable effect on the performance of the AS-NBR insulation. This paper will discuss some of the raw material and process changes evaluated, the methodology used in designing the unique test plans, and the general evaluation results. A summary of the change history of RSRM AS-NBR internal insulation is also presented.

  17. Evaluation of effectiveness of raw materials and materials use in a blast furnace department of a steelworks

    E. Kardas

    2017-01-01

    Full Text Available The paper analyses the quality of raw materials used in the production of blast furnace pig iron. The ferruginous sinter and pellets are the basic raw materials used in the process. The paper presents the impact of those raw materials quality on the effectiveness of the blast furnace process. The process effectiveness will be specified by means of selected process parameters.

  18. Thorium and Uranium in the Rock Raw Materials Used For the Production of Building Materials

    Pękala, Agnieszka

    2017-10-01

    Thorium and uranium are constant components of all soils and most minerals thereby rock raw materials. They belong to the particularly dangerous elements because of their natural radioactivity. Evaluation of the content of the radioactive elements in the rock raw materials seems to be necessary in the early stage of the raw material evaluation. The rock formations operated from deposits often are accumulated in landfills and slag heaps where the concentration of the radioactive elements can be many times higher than under natural conditions. In addition, this phenomenon may refer to buildings where rock raw materials are often the main components of the construction materials. The global control system of construction products draws particular attention to the elimination of used construction products containing excessive quantities of the natural radioactive elements. In the presented study were determined the content of thorium and uranium in rock raw materials coming from the Bełachatów lignite deposit. The Bełchatów lignite deposit extracts mainly lignite and secondary numerous accompanying minerals with the raw material importance. In the course of the field works within the framework of the carried out work has been tested 92 samples of rocks of varied petrographic composition. There were carried out analyses of the content of the radioactive elements for 50 samples of limestone of the Jurassic age, 18 samples of kaolinite clays, and 24 samples of siliceous raw materials, represented by opoka-rocks, diatomites, gaizes and clastic rocks. The measurement of content of the natural radioactive elements thorium and uranium based on measuring the frequency counts of gamma quantum, recorded separately in measuring channels. At the same time performed measurements on volume patterns radioactive: thorium and uranium. The studies were carried out in Mazar spectrometer on the powdered material. Standardly performed ten measuring cycles, after which were calculated

  19. Process for the production of high purity deuterium

    Arrathoon, R.

    1977-01-01

    A process for the electrolysis of heavy water which results in the production of high purity deuterium without periodic replenishment of the electrolyte with additional deuterated compounds is defined. Electrolysis is effected through the use of an inexpensive cation-action permselective membrane which is essentially a solid polymer electrolyte and which is capable of automatically separating the evolved deuterium and oxygen gas. This cation-active permselective membrane does not introduce any intrinsic impurities or tritium contamination in the generated deuterium gas, does not require periodic revitalization with deuterated compounds or other chemical compounds, and is characterized by an unusually high electrical efficiency

  20. Neutron activation analysis of high-purity zinc

    Khodzhamberdyeva, A.A.; Usmanova, M.M.; Gil'bert, Eh.N.; Ivanov, I.M.; Yankovskaya, T.A.; Kholyavko, E.P.

    1987-01-01

    The methods of neutron activation analysis of high-purity zinc with preliminary separation of the zinc base using extraction by trialkylbenzylammonium rhodanide in carbon tetrachloride from 0.5-2.0 M nitric acid solutions is developed. Only rhenium is quantitatively extracted together with zinc. Gold, iridium and molybdenum are extracted to 50-60%, and selenium - to 20%. The Na, K, La, Cr, Sc, Co, Cs, Rb, Fe, Zr, Sn, Te, As, Cd, Hf, W, Sb, Sm impurities remain in the aqueous phase. The methods permits to determine the impurities above with detection limits from 1x10 -6 to 4x10 -11 g

  1. The ion-exchange obtaining of high purity samarium oxide

    Brzyska, W.; Soltysiak, I.; Cygan, J.

    1987-01-01

    The use of lactic acid - EDTA mixture as an eluent for the obtaining of high purity samarium oxide was studied. The studies were carried out at room temperature on cation exchange resin Wofatit KPS X 8. The best results were obtained for lactic acid (0,26 mol/dm 3 ) - EDTA (0,013 mol/dm 3 ) mixture at pH 3,3. As the result of 57% samarium concentrate elution with column load 1:3 and flow rate 0,4 cm/min, over 99% pure samarium oxide with 73% yield has been obtained. The yield of spectrally pure Sm 2 O 3 exceeded 45%. (author)

  2. Release characteristics of tritium from high-purity lithium oxide

    O'Kula, K.R.; Vogelsang, W.F.

    1985-01-01

    Rates of tritium release from neutronirradiated lithium oxide were determined from isothermal release experiments. High-purity, monocrystalline lithium oxide was purged ex-reactor with helium and helium-hydrogen gas streams. Overall release was found to be controlled by solid-phase diffusion, and was predominantly in the form of condensible species. The result of an independent concentration profile analysis at 923 K was in agreement with the gas release diffusion coefficient. Sweeping the Li 2 O with hydrogen-containing gas was found to enhance tritium removal during the early stage of each run

  3. Amplitude dependent damping in single crystalline high purity molybdenum

    Zelada-Lambri, G.I; Lambri, O.A; Garcia, J.A; Lomer, J.N

    2004-01-01

    Amplitude dependent damping measurements were performed on high purity single crystalline molybdenum at several different constant temperatures between room temperature and 1273K. The employed samples were single crystals with the orientation, having a residual resistivity ratio of about 8000. Previously to the amplitude dependent damping tests, the samples were subjected to different thermomechanical histories. Amplitude dependent damping effects appear only during the first heating run in temperature where the samples have the thermomechanical state of the deformation process at room temperature. In the subsequent run-ups in temperature, i.e, after subsequent annealings, amplitude dependent damping effects were not detected (au)

  4. Emergy analysis of biogas systems based on different raw materials.

    Wang, Yang; Lin, Cong; Li, Jing; Duan, Na; Li, Xue; Fu, Yanyan

    2013-01-01

    Environmental pollution and energy crisis restrict the development of China, and the utilization of renewable technology is an effective strategy to alleviate the damage. Biogas engineering has rapidly developed attributes to solve environmental problems and create a renewable energy product biogas. In this paper, two different biogas plants' materials were analyzed by emergy method. One of them is a biogas project whose degraded material is feces (BPF system), and the other is the one whose degraded material is corn straw (BPC system). As a result, the ecological-economic values of BPF and BPC are $28,300/yr and $8,100/yr, respectively. Considering currency, environment, and human inputs, both of the biogas projects have the ability of disposing waste and potential for development. The proportion of biogas output is much more than fertilizer output; so, fertilizer utilization should be emphasized in the future. In comparison, BPF is better than BPC in the aspects of ecological-economic benefits, environmental benefits, and sustainability. The reason is the difficulty of corn straw seasonal collection and degradation. Thus it is proposed that BPC should be combined with the other raw materials.

  5. Emergy Analysis of Biogas Systems Based on Different Raw Materials

    Yang Wang

    2013-01-01

    Full Text Available Environmental pollution and energy crisis restrict the development of China, and the utilization of renewable technology is an effective strategy to alleviate the damage. Biogas engineering has rapidly developed attributes to solve environmental problems and create a renewable energy product biogas. In this paper, two different biogas plants’ materials were analyzed by emergy method. One of them is a biogas project whose degraded material is feces (BPF system, and the other is the one whose degraded material is corn straw (BPC system. As a result, the ecological-economic values of BPF and BPC are $28,300/yr and $8,100/yr, respectively. Considering currency, environment, and human inputs, both of the biogas projects have the ability of disposing waste and potential for development. The proportion of biogas output is much more than fertilizer output; so, fertilizer utilization should be emphasized in the future. In comparison, BPF is better than BPC in the aspects of ecological-economic benefits, environmental benefits, and sustainability. The reason is the difficulty of corn straw seasonal collection and degradation. Thus it is proposed that BPC should be combined with the other raw materials.

  6. Emergy Analysis of Biogas Systems Based on Different Raw Materials

    Wang, Yang; Lin, Cong; Li, Jing; Duan, Na; Li, Xue; Fu, Yanyan

    2013-01-01

    Environmental pollution and energy crisis restrict the development of China, and the utilization of renewable technology is an effective strategy to alleviate the damage. Biogas engineering has rapidly developed attributes to solve environmental problems and create a renewable energy product biogas. In this paper, two different biogas plants' materials were analyzed by emergy method. One of them is a biogas project whose degraded material is feces (BPF system), and the other is the one whose degraded material is corn straw (BPC system). As a result, the ecological-economic values of BPF and BPC are $28,300/yr and $8,100/yr, respectively. Considering currency, environment, and human inputs, both of the biogas projects have the ability of disposing waste and potential for development. The proportion of biogas output is much more than fertilizer output; so, fertilizer utilization should be emphasized in the future. In comparison, BPF is better than BPC in the aspects of ecological-economic benefits, environmental benefits, and sustainability. The reason is the difficulty of corn straw seasonal collection and degradation. Thus it is proposed that BPC should be combined with the other raw materials. PMID:23476134

  7. Utilization of raw material from early thinnings; Ensiharvennuspuun hyoedyntaeminen

    Alen, R; Marttina, M; Toivanen, J [Jyvaeskylae Univ. (Finland). Dept. of Chemistry

    1997-12-01

    Wood material from early thinnings is one of the most potential new material reserves (4 - 6 million m{sup 3}) for industrial purposes. However, the prerequisites for an enhanced utilisation of this reserve would be, besides more efficient logging, debarking, and chipping, an optimal fractionation of wood material into energy and fibre production. The aim of this project was to promote the use of first-thinning wood as a competitive raw material for energy production by increasing the potential utilisation of the corresponding wood resource for chemical pulping. During the year 1996 the variation of fibre length distribution within the stem and top (total height of 12 m) of a 27-years-old pine wood (Pinus sylvestris) was determined. Tentative calculations indicated that about 67 % of the wood dry matter consists of fibres having an average fibre length more than 2 mm. It was considered that most of this fraction with high quality fibre properties could be recovered and used for pulping. In addition, the detailed FTIR analysis of different samples from the same pine wood showed that there was an adequate correlation between the FTIR spectrometric data and the fibre length averages. (orig.)

  8. Self-compacting paste system using secondary raw materials

    Rizwan, S.A.

    2008-01-01

    A study has been carried out on self-compacting paste (SCP) systems using various cements and secondary raw materials (SRM's) including rice husk ash (RHA) and Silica Fume (SF). These systems were characterized by: SRM particle size, powder water demand (WD) and setting times, flow, strength, microstructure and early volume stability. The result show that WD increased by adding SRM's due to their smaller particle size, higher surface area and internal porosity. Inclusion of SRM's in SCP systems as cement replacements also increase strength of SCP systems due to filler, hydration and pozzolanic actions which translate into pore refinement. It is demonstrated that the resultant properties of self-compacting cementitious. System (SCCS) depend upon the nature of SRM used. (author)

  9. Glances on the year 1998. Energies and raw materials

    1999-01-01

    This report summarizes 14 key-topics of the year 1998 in relation with the French energy and economic policy: the new start-up of energy mastery; the nuclear industry between passion and reason; the labour inspection in nuclear power plants; the law project for the modernizing and development of the electric power public utility; the main gas transportation systems; the future of Gardanne's mining basin; the raw materials in the upheaval; the French refining activity after the Auto-Oil directive; the oil company fusions; the priorities in petroleum technology research; the policy of automotive fuels distribution; the energy in regions; the mining activity in New Caledonia; the end of the BRGM-Normandy partnership. A calendar of remarkable facts is given at the end. (J.S.)

  10. The characteristics of bioethanol fuel made of vegetable raw materials

    Muhaji; Sutjahjo, D. H.

    2018-01-01

    The aim of this research is to identify the most potential vegetable raw as the material to make a bioethanol fuel as the alternative energy for gasoline. This study used experimental method. The high-level bioethanol was obtained through the process of saccharification, fermentation and stratified distillation. ASTM standards were used as the method of testing the chemical element (D 5501, D 1744, D 1688, D 512, D 2622, D 381), and physical test (D 1613, D 240, D 1298-99, D 445, and D 93). The result of the analysis showed that from the seven bioethanols being studied there is one bioethanol from Saccharum of icinarum linn that has physical and chemical properties close to the standard of bioethanol. Meanwhile, the others only meet some of the physical and chemical properties of the standard bioethanol.

  11. National reports on raw materials economy. Vol. 6

    Haude, H.; Weber, R.

    1975-06-01

    A review is given of the ore deposits, mine production, and use of mineral resources in Argentina (oil, gas, asphalt, oil shale, coal, uranium, thorium, iron, manganese, chrome, tungsten, vanadium, copper, lead, zinc, tin, antimony, gold, silver, aluminium, beryllium, boron, sulfur, and fluorite). Argentina is dependent on imports of nearly all mineral resources. Only exports of zinc, tungsten, fluorite, and borate have been possible and the only other significant production has been of energy resources, iron, manganese, and lead. The extreme concentration of population in the east, the great distances to the Andes in the west, and the as yet inadequate transport network with the west has limited the mining activity up to the present. As part of industrial development, the government has made great efforts to increase the supply of raw materials through intensive prospecting and use of Argentina's own natural resources. Newly discovered ore deposits confirm that extensive parts of the country are prospective for mineral resources. (orig.) [de

  12. Radioactive contaminants in raw materials and foodstuffs of plant origin

    Stankovicj, S.; Krainchanicj, M.; Stankovicj, A.

    1990-01-01

    The paper concentrates on the results of activity level of radioactive caesium 134 and 137 in the samples of raw materials (barley, oats, soybean, sunflower, pumpkin seed, hops, shreded sugar beet, maize), animal feedstuffs (alfalfa, alfalfa meal, rape, concentrates fed to chickens, pigs or bpvines, dry turnip shreds) and foodstuff of plant origin (lettuce, spinach, cabbage, carrot, celery, cucumber, tomato, olives, sesame). All samples - produced locally on the major part but also including some imported stuff -have been subjected to continuous gamma spectrometry starting with the Chernobyl accident in 1986 through 1989. The highest activity of caesium was recorded in the samples of animal feedstuffs (alfalfa, alfalfa meal, rape) in the years 1986 and 1987. In time, however, the activity tends to drop considerably. (author) 4 refs.; 3 tabs

  13. Raw materials problems in connection with fast breeder type reactors

    Hirsch, H.; Kreusch, J.

    1981-01-01

    The power supply by the FBR type reactors which depends upon the availability of essential raw materials such as Cr and Mo for structural and special steels is supposed to be less ensured than supply by fossil-fueled power plants. This contribution tries to verify this statement by means of estimates of the annual Cr and Mo demand, of the resources, production and consumption as well as by a study of the possibilities of recycling and substituting Cr and Mo. The only realistic alternative to the fast breeder type reactor is supposed to be a soft path of development according to the principle of decentralization, utilization of renewable energy sources regard to environmental protection, and use of less sophisticated technology. (DG) [de

  14. The Energy Transition and the Challenge of Critical Raw Materials

    Lepesant, Gilles

    2018-01-01

    The geopolitical analyses of energy markets are traditionally focused on fossil fuels, and less on renewable energy sources. Yet the huge development perspectives of these renewable energy sources (representing 2/3 of total net power generation capacity additions in 2016) trigger a need to take into account new challenges and vulnerabilities, related to the availability and affordability of critical raw materials, notably rare earths, which are needed to develop wind turbines, solar panels and energy storage technologies. Stakes are geopolitical, economic and environmental and are reinforced by a geography of resources and production which is concentrated within a few key countries and zones (China, Latin America, Australia, Congo mainly). The role of China in particular is at the core of the attention

  15. Cross-laminated timber made of Hungarian raw materials

    Marko, G.; Bejo, L.; Takats, P.

    2016-04-01

    Cross-laminated timber (CLT), generally made out of softwood, enjoys increasing popularity throughout Europe. This material offers a versatile, eco-friendly technology to create strong, lightweight and energy-efficient buildings. Unfortunately, the sites and climatic conditions in Hungary are not suitable for growing high-quality coniferous trees. Transporting raw materials from other countries (sometimes thousands of kilometres away) negates the environmental advantages of wood-based construction. Local options are definitely preferable from an ecological aspect. Poplar wood (populus spp.) is of great economic importance in Hungary. There are several relatively high density, high strength varieties growing in large quantities in Hungary, that may be used as alternatives to softwood, with comparable properties. There is an increasing interest in using poplar as a construction material, especially in regions were there is a shortage of traditional construction timber. This paper presents the results of a preliminary investigation to create CLT using poplar lumber. Laboratory-scale CLT specimens were created in a hot press, and tested for their loadbearing capacity. The MOR values of poplar CLT are comparable to, albeit somewhat lowerthan those of softwood CLT. Further investigations are required to establish the economic viability and technological conditions for the commercial production of poplar CLT.

  16. Synthesis of high purity tungsten nanoparticles from tungsten heavy alloy scrap by selective precipitation and reduction route

    Kamal, S.S. Kalyan; Sahoo, P.K.; Vimala, J.; Shanker, B.; Ghosal, P.; Durai, L.

    2016-01-01

    In this paper we report synthesis of tungsten nanoparticles of high purity >99.7 wt% from heavy alloy scrap using a novel chemical route of selective precipitation and reduction. The effect of Poly(vinylpyrrolidone) polymer on controlling the particle size is established through FTIR spectra and corroborated with TEM images, wherein the average size decreased form 210 to 45 nm with increasing PVP content from zero to 2 g under different experimental conditions. This process is economical as raw material is a scrap and the efficiency of the reaction is >95%. - Highlights: • Tungsten nanoparticles were synthesized from tungsten heavy alloy scrap. • A novel chemical route of precipitation and reduction with Poly(vinylpyrrolidone) polymer as stabilizer is reported. • The average size decreased form 210 to 45 nm with increasing PVP content from zero to 2 g. • High pure tungsten nanoparticles of >99.7% purity could be synthesized using this route. • Efficiency of the reaction is >95%.

  17. High Purity Silica Production from Rice Husk Ash

    Yaminn Lwin; April Nwayy Nwayy Htett

    2010-12-01

    In this research, two types of raw material source, rice husk and rice husk ash, were used. Among the rice husk samples, taungpyan sample was chosen because it contains the maximum silica content and treated with (1,3,5) wt% sulphuric acid (96% concentration) and citric acid (99% concentration). These acid treated taungpyan samples and nonacid treated taungpyan sample were burned at 900C for 30 min. For rice husk ash samples, ash samples from fluidized combustor, fluidized gasifier and brick factory were collected. All of the rice husk ash samples were purified by alkaline extraction method with (2-3) N NaOH solution and followed by acid precipitation method with 5 N H2SO4 solution. According to the analysis and characterization, acid treated taungpyan sample (5 wt% citric acid) with the highest silica content (99.906 wt% and crystallization form) was obtained.

  18. Polymer Industrial Floors - The Possibility of Using Secondary Raw Materials from Solar Panels

    J. Kosikova; B. Vacenovska; M. Vyhnankova

    2014-01-01

    The paper reports on the subject of recycling and further use of secondary raw materials obtained from solar panels, which is becoming a very up to date topic in recent years. Recycling these panels is very difficult and complex, and the use of resulting secondary raw materials is still not fully resolved. Within the research carried out at the Brno University of Technology, new polymer materials used for industrial floors are being developed. Secondary raw materials are ...

  19. Local deposition of high-purity Pt nanostructures by combining electron beam induced deposition and atomic layer deposition

    Mackus, A.J.M.; Mulders, J.J.L.; Sanden, van de M.C.M.; Kessels, W.M.M.

    2010-01-01

    An approach for direct-write fabrication of high-purity platinum nanostructures has been developed by combining nanoscale lateral patterning by electron beam induced deposition (EBID) with area-selective deposition of high quality material by atomic layer deposition (ALD). Because virtually pure,

  20. Design and development of fluidized bed reactor system for production of trichlorosilane as a precursor for high purity silicon

    Kumar, Rajesh; Mohan, Sadhana; Bhanja, K.; Nayak, S.; Bhattacharya, S.K.

    2009-01-01

    Trichlorosilane is widely used as precursor material for production of high purity silicon. It is mainly produced by reaction of metallurgical grade silicon with anhydrous HCl gas in a fluidized bed reactor. To develop this process on commercial scale a pilot size fluidized bed reactor system was designed and developed and successfully operated. This paper discusses the critical issues related to these activities. (author)

  1. Influence of man-made aluminosilicate raw materials on physical and mechanical properties of building materials.

    Volodchenko, A. A.; Lesovik, V. S.; Stoletov, A. A.; Glagolev, E. S.; Volodchenko, A. N.; Magomedov, Z. G.

    2018-03-01

    It has been identified that man-made aluminosilicate raw materials represented by clay rock of varied genesis can be used as energy-efficient raw materials to obtain efficient highly-hollow non-autoclaved silicate materials. A technique of structure formation in the conditions of pressureless steam treatment has been offered. Cementing compounds of non- autoclaved silicate materials based on man-made aluminosilicate raw materials possess hydraulic properties that are conditioned by the process of further formation and recrystallization of calcium silicate hydrates, which optimizes the ratio between gellike and crystalline components and densifies the cementing compound structure, which leads to improvement of performance characteristics. Increasing the performance characteristics of the obtained products is possible by changing the molding conditions. For this reason, in order to create high-density material packaging and, as a result, to increase the strength properties of the products, it is reasonable to use higher pressure, under which raw brick is formed, which will facilitate the increase of quality of highly-hollow products.

  2. Advances in the hydrometallurgical separation techniques of high purity rare earth elements

    Vijayalakshmi, R.; Kain, V.

    2017-01-01

    Rare Earths are a series of 15 chemically similar elements that occur together in monazite mineral found in the beach sands of Kerala, Tamil Nadu and Orissa. The rare earth elements (REE) are becoming increasingly strategically important considering their essential role in permanent magnets such as, SmCo_5, Sm_2Co_1_7 and Nd_2Fe_1_4B, phosphors for LED screens and lamps, rechargeable nickel metal hydride batteries and catalysts and other green applications. The increasing popularity of hybrid and electric cars, wind turbines and compact fluorescent lamps is causing an increase in the demand and price of REE. The European Commission considers the REE as the most critical raw materials group, with the highest supply risk. According to the medium-term criticality matrix of the U.S. Department of Energy (DOE), the five most critical REE are neodymium (Nd), europium (Eu), terbium (Tb), dysprosium (Dy) and yttrium (Y). China is presently producing more than 90% of all rare earths, although they possess less than 405 of the proven reserves. Due to large and increasing domestic demands, China tightened its REE export quota from 2012 onwards. These export quotas caused serious problems for REE users outside of China. Fortunately India is blessed with large resources of rare earths in the form of monazite found in the beach sands of Kerala, Tamil Nadu and Orissa. Indian Rare Earths Limited at Aluva near Kochi produces mainly mixed rare earths chloride and till recent past exporting to USA, UK, France, Japan, etc. They have revived their rare earth separation plant to meet the in-house demands of the strategic, defense and nuclear industry. This paper discusses the recent advances made in hydrometallurgical separation techniques based on solvent extraction technique, ion-exchange resins, hollow fibre membrane extractor, solvent encapsulated polymeric beads, etc for the production of high purity rare earth elements from both primary (Monazite, xenotime) and secondary sources

  3. Rare earth elements exploitation, geopolitical implications and raw materials trading

    Chemin, Marie-Charlotte

    2015-04-01

    , establishing a company in China can lower the production cost (since the company buys the products used in its production at a lower price). In the fifth session, they study the raw materials trading based on the futures contracts example. A producer, to avoid a rise in prices of raw materials used in his production can use derivative products on the financial market: futures contracts for instance. This product ensures a quantity and quality for a price and a delivery date agreed upon today. Actually, producers can use a method called Fix price hedging in order to fix the price of a specific product. The main idea is to balance out the "physical position" (spot market) and the "paper position" (futures market). Even if the REE are commercialized in form of a non-perishable's oxide, the flow of the stock must be guaranteed and this is why it is important for producers to secure their supply of raw materials. In the last session, students search local companies that use REE in their production process and study their strategy on the market.

  4. Deuterium permeation and diffusion in high-purity beryllium

    Abramov, E.; Riehm, M.P.; Thompson, D.A.; Smeltzer, W.W.

    1990-01-01

    The permeation rate of deuterium through high-purity beryllium membranes was measured using the gas-driven permeation technique. The time-dependent and the steady-state deuterium flux data were analyzed and the effective diffusivities of the samples were determined. Using multilayer permeation theory the effects of surface oxide were eliminated and the diffusion coefficients of the bulk beryllium determined. The diffusion parameters obtained for the extra-grade beryllium samples (99.8%) are D 0 =6.7x10 -9 m 2 /s and E D =28.4 kJ/mol. For the high-grade beryllium samples (99%) the parameters are D 0 =8.0x10 -9 m 2 /s and E D =35.1 kJ/mol. (orig.)

  5. Deuterium permeation and diffusion in high purity beryllium

    Abramov, E.

    1990-05-01

    The permeation rate of deuterium through high-purity beryllium membranes was measured using the gas-driven permeation technique. The time-dependent and the steady-state deuterium flux data were analyzed and the effective diffusivities of the samples were determined. A multilayer permeation theory was used in order to eliminate the surface oxide effects and the diffusion coefficients of the bulk beryllium were determined. The diffusion parameters obtained for the extra-grade beryllium samples (99.8%) are D 0 = 6.7 x 10 -9 [m 2 /s] and E D = 28.4 [KJ/mol]; and for the high-grade beryllium samples (99%) the parameters are D 0 = 8.0 x 10 -9 [m 2 /s] and E D = 35.1 [KJ/mol

  6. Thermal and electrical conductivities of high purity tantalum

    Archer, S.L.

    1978-01-01

    The electrical resistivity and thermal conductivity of three high purity tantalum samples have been measured as functions of temperature over a temperature range of 5K to 65K. Sample purities ranged up to a resistivity ratio of 1714. The highest purity sample had a residual resistivity of .76 x 10 -10 OMEGA-m. The intrinsic resistivity varied as T 3 . 9 from 10K to 31K. The thermal conductivity of the purest sample had a maximum of 840 W/mK at 9.8K. The intrinsic thermal resistivity varied as T 2 . 4 from 10K to 35K. At low temperatures electrons were scattered primarily by impurities and by phonons with both interband and intraband transitions observed. The electrical and thermal resistivity is departed from Matthiessen's rule at low temperatures

  7. Preparation of high purity yttrium single crystals by electrotransport

    Volkov, V.T.; Nikiforova, T.V.; Ionov, A.M.; Pustovit, A.N.; Sikharulidse, G.G.

    1981-01-01

    The possibility of obtaining yttrium crystals of high purity by the method of solid state electrotransport (SSE) was investigated in the present work. The behaviour of low contents of iron, aluminium, silicon, tantalum, copper, silver and vanadium as metallic impurities was studied using mass spectrometry. It is shown that all the impurities investigated, except copper, migrate to the anode. During electrotransfer a purification with respect to these impurities by a factor of 4 - 6 is obtained. It is proposed that the diffusion coefficients of the metallic impurities investigated are anomalously high and that the behaviour of the impurities during SSE in adapters necessitates further investigation. By using a three-stage process with intermediate removal of the anode end yttrium single crystals with a resistance ratio rho 293 /rhosub(4.2)=570 were produced. (Auth.)

  8. TIGRESS highly-segmented high-purity germanium clover detector

    Scraggs, H. C.; Pearson, C. J.; Hackman, G.; Smith, M. B.; Austin, R. A. E.; Ball, G. C.; Boston, A. J.; Bricault, P.; Chakrawarthy, R. S.; Churchman, R.; Cowan, N.; Cronkhite, G.; Cunningham, E. S.; Drake, T. E.; Finlay, P.; Garrett, P. E.; Grinyer, G. F.; Hyland, B.; Jones, B.; Leslie, J. R.; Martin, J.-P.; Morris, D.; Morton, A. C.; Phillips, A. A.; Sarazin, F.; Schumaker, M. A.; Svensson, C. E.; Valiente-Dobón, J. J.; Waddington, J. C.; Watters, L. M.; Zimmerman, L.

    2005-05-01

    The TRIUMF-ISAC Gamma-Ray Escape-Suppressed Spectrometer (TIGRESS) will consist of twelve units of four high-purity germanium (HPGe) crystals in a common cryostat. The outer contacts of each crystal will be divided into four quadrants and two lateral segments for a total of eight outer contacts. The performance of a prototype HPGe four-crystal unit has been investigated. Integrated noise spectra for all contacts were measured. Energy resolutions, relative efficiencies for both individual crystals and for the entire unit, and peak-to-total ratios were measured with point-like sources. Position-dependent performance was measured by moving a collimated source across the face of the detector.

  9. Precipitation of hydrides in high purity niobium after different treatments

    Barkov, F.; Romanenko, A.; Trenikhina, Y.; Grassellino, A.

    2013-01-01

    Precipitation of lossy non-superconducting niobium hydrides represents a known problem for high purity niobium in superconducting applications. Using cryogenic optical and laser confocal scanning microscopy we have directly observed surface precipitation and evolution of niobium hydrides in samples after different treatments used for superconducting RF cavities for particle acceleration. Precipitation is shown to occur throughout the sample volume, and the growth of hydrides is well described by the fast diffusion-controlled process in which almost all hydrogen is precipitated at $T=140$~K within $\\sim30$~min. 120$^{\\circ}$C baking and mechanical deformation are found to affect hydride precipitation through their influence on the number of nucleation and trapping centers.

  10. Investigation of sulphides in iron alloys of high purity

    Wyjadlowski, T.

    1973-01-01

    This research thesis reports the study of the morphology and composition of sulphides in iron alloys with respect to metal composition and to the nature of impurities. In order to understand the specific action of each addition on inclusion morphology, this work has started with high-purity alloys (binary alloys and then ternary alloys). The author studied whether solubility variations would entail either intergranular or intragranular or hybrid iron sulphide precipitation. He examined whether sulphide morphology is depending on thermal treatment, and whether equilibrium precipitates were different in terms of morphology and composition at high and room temperature. He studied the influence of addition elements on sulphide morphology and composition, an important issue as some elements may reduce brittleness. These elements are classified in terms of affinity with sulphur

  11. Study of chemisrty and hydrolysates drying parameters of feather-downy raw material

    LISITSYN A.B.; KRIGER O.V.; MITROKHIN P.V.

    2016-01-01

    The article describes chemical and amino acid composition of feather-downy raw material. It determines the mass fraction of crude protein, crude fiber, ash, calcium, phosphorus, sodium in the samples of feather-downy raw material. It is stated that the waste from poultry processing obtained from hens of all the studied species are characterized by a high content of crude protein and low in crude fiber and ash. The most valuable feather-downy raw material regarding protein is waste containing ...

  12. Primary Raw Materials for Steelmakers: Scrap and Pig Iron

    Cristina Bumbac

    2011-10-01

    Full Text Available Most of the daily steel we so much need is obtained now in electric furnaces, for which the main raw material is scrap. The scrap market is a very sensitive one, depending very much on internal collect, exports and imports, the market of steel and freight. Commerce with scrap is one of the most intense among all the countries of the world and covers all the routes and regions. Every ten years or so importers become exporters and vice versa, due to the period of life of the metallic products. For example, China was for the last 10 years one of the biggest importers (after Turkey, which is number one in importers' hierarchy, but prognoses tell that in 2-3 years China might become self-sufficient due to the investments which began some 20 years ago. USA was one of the largest exporters, but some 3 years ago some analysts advanced the idea that it may become a net importer (it didn't happened, though. The scrap market is not only important, it is also very interesting, with twisted evolutions and volatile prices in some periods.

  13. Bearberry identification by a multidisciplinary study on commercial raw materials.

    Gallo, Francesca Romana; Multari, Giuseppina; Pagliuca, Giordana; Panusa, Alessia; Palazzino, Giovanna; Giambenedetti, Massimo; Petitto, Valentina; Nicoletti, Marcello

    2013-04-01

    Herbal species different from the official bearberry, Arctostaphylos uva-ursi, are sold through conventional markets and also through non-controlled Internet websites, putting consumer safety at risk owing to the lack of quality control. Recently, Arctostaphylos pungens has become one of the most used species as a raw material for herbal medicines and dietary supplements in the place of official bearberry, a plant used for the treatment of various urinary disorders. A fingerprint identification based on an integrated application of different analytical techniques (HPTLC, NMR, HPLC-DAD and LC-ESI-MS) is here described to distinguish A. uva-ursi from A. pungens. The HPTLC and HPLC-DAD fingerprints resulted the simplest methods to differentiate the two species, whereas LC-ESI-MS was more useful to quantify arbutin, the main component of bearberry, and to evaluate its different content in the two species. This multidisciplinary study showed for the first time a specific phytochemical fingerprint of the new species A. pungens.

  14. Climate changes, raw materials shortage, and economic development

    Joest, F.

    1994-01-01

    The possibility of a climate change being brought about by our national economies has dominated the national and international ecopolitical discussion of the past few years like no other topic. The present study is an attempt at an as comprehensive an examination as possible of this problem. It works from the assumption that examining and solving environmental problems requires the cooperation and creativity of investigators from different disciplines. It accordingly develops a concept permitting an integration of scientific, economic, and ethical questions impinging on the problem of the greenhouse effect. Thus the study contributes to the groundwork of an ecological economics. The interdisciplinary approach to analysing the connections between climate changes, raw materials consumption, and economic development is variously seen to pinpoint the complex temporal structure of the problems. It becomes clear that ecopolitical measures take a long time to actually become effective. Besides shifiting the focus to questions as to the scope and limits of politico-economic action, the temporal strucutre of the problem also reveals the limitations of scientifically founded ecopolitical recommendations. This brings the ethical aspect of analysing and solving environmental problems to the fore. (orig./UA) [de

  15. Plant development effects of biochars from different raw materials

    Cely, Paola; Méndez, Ana; Paz-Ferreiro, Jorge; Gascó, Gabriel

    2015-04-01

    Biochar can provide multiple benefits in the ecosystem. However, the presence of phytotoxic compounds in some biochars is an important concern that needs to be addressed and that depends on the raw material and the pyrolysis conditions used in biochar production. For example, sewage sludge biochars can have elevated heavy metal contents as they were present in the feedstock and were enriched during pyrolysis. Also during carbonization, some phytotoxic compounds such as polycyclic aromatic hydrocarbons (PAHs), polyphenols or volatile organic compounds (VOCs) could be formed representing a risk of contamination to soils and crops. In this work we report the results from seed germination and plant development for three biochars prepared from wood, paper sludge plus wheat husks and sewage sludge. Five higher plant species (cress, lentils, cucumber, tomato and lettuce) were studied. Biochar from wood shows seed inhibition in several species and the paper sludge biochar on lettuce. For the rest, the effect on seed germination was positive. No inhibition of root growth was detected, but in some cases leaves and stems growth were inhibited. Our results are significant in terms of advancing or current understanding on the impacts of biochar on vegetative growth and linking those effects to biochar properties.

  16. Use of basaltic waste as red ceramic raw material

    T. M. Mendes

    Full Text Available Abstract Nowadays, environmental codes restrict the emission of particulate matters, which result in these residues being collected by plant filters. This basaltic waste came from construction aggregate plants located in the Metropolitan Region of Londrina (State of Paraná, Brazil. Initially, the basaltic waste was submitted to sieving (< 75 μm and the powder obtained was characterized in terms of density and particle size distribution. The plasticity of ceramic mass containing 0%, 10%, 20%, 30%, 40% and 50% of basaltic waste was measured by Atterberg method. The chemical composition of ceramic formulations containing 0% and 20% of basaltic waste was determined by X-ray fluorescence. The prismatic samples were molded by extrusion and fired at 850 °C. The specimens were also tested to determine density, water absorption, drying and firing shrinkages, flexural strength, and Young's modulus. Microstructure evaluation was conducted by scanning electron microscopy, X-ray diffraction, and mercury intrusion porosimetry. Basaltic powder has similar physical and chemical characteristics when compared to other raw materials, and contributes to ceramic processing by reducing drying and firing shrinkage. Mechanical performance of mixtures containing basaltic powder is equivalent to mixtures without waste. Microstructural aspects such as pore size distribution were modified by basaltic powder; albite phase related to basaltic powder was identified by X-ray diffraction.

  17. The key numbers of the mineral raw materials

    Mandil, C.

    1996-01-01

    Mineral raw materials come from fossil reserves or ores resulting from the geologic and climatic history of the Earth. The access to economic development for 80% of the worldwide population and the high rate of demographic growth (probably 8 billions of inhabitants in 2025) are important factors that can greatly multiply the worldwide consumption of ores. In parallel, environmental concerns and the increasing need for a better equilibrium between wildlife preservation and the supply of economic needs, lead to a more reasonable and mastered use of natural resources. The aim of this book is to shade light and give global elements of thoughts on mineral resources, and for the main of those (about 30 metals and mineral substances), to review the most useful data and references about their production and consumption. For each question, chapters are devoted to the situation of France in its worldwide context. One chapter concerns the uranium ores (reserves, production, prices evolution, consumption, economic flux and companies involved). (J.S.)

  18. Radiation situation during underground mineral raw materials mining

    Ogorodnikov, B.I.

    2007-01-01

    One studied the content and the ratio of 4 0 K, 226 Ra, 232 Th and 238 U natural radionuclides in the ores mined in Egypt, Iran, China and Turkey. It is shown that in some ores, for example, in the carbonaceous shale mined in China, in the Iranian bauxite and turquoise Ra eq is higher than 370 Bq/kg, that is, it is higher than the value recommended by the International Scientific Committee on Radiation Effect. The Chinese bituminous shale shows high content of 226 Ra, while 226 Ra/ 232 Th concentration ratio varies between 10 and 60 in contrast to that of other numerous mineral raw materials being close to 1-3. In a number of mines one recorded high concentrations of radon (higher than 300 Bq/m 3 ). Inhalation of such an air results in the essential internal irradiation. The average annual dose equivalents for miners may be higher than the maximum permissible value equal to 20 mSv/g [ru

  19. Study on optimum length of raw material in stainless steel high-lock nuts forging

    Cheng, Meiwen; Liu, Fenglei; Zhao, Qingyun; Wang, Lidong

    2018-04-01

    Taking 302 stainless steel (1Cr18Ni9) high-lock nuts for research objects, adjusting the length of raw material, then using DEFORM software to simulate the isothermal forging process of each station and conducting the corresponding field tests to study the effects of raw material size on the stainless steel high-lock nuts forming performance. The tests show that the samples of each raw material length is basically the same as the results of the DEFORM software. When the length of the raw material is 10mm, the appearance size of the parts can meet the design requirements.

  20. Development and Testing the Technology of Complex Transformation of Carbohydrates from Vegetable Raw Materials into Bioethanol

    S.P. Tsygankov

    2013-07-01

    Full Text Available Results of development and testing the tentative technology of sweet sorghum and finger millet processing into bioethanol are described. The carbohydrates content and range of the studied vegetable biomass as the raw material is defined. Bioethanol potential output from sugar sorghum and finger millet carbohydrates and key technological parameters of preparation of both types of vegetable raw material for alcohol fermentation are defined. The concept of the tentative technology of bioethanol production from carbohydrate raw material of the first and second generations is offered. Testing of complex transformation of carbohydrates from vegetable raw materials into bioethanol is performed.

  1. Comparison of Different Wood Species as Raw Materials for Bioenergy

    Bojana Klašnja

    2013-12-01

    Full Text Available Background and Purpose: Most projections of the global energy use predict that biomass will be an important component of primary energy sources in the coming decades. Short rotation plantations have the potential to become an important source of renewable energy in Europe because of the high biomass yields, a good combustion quality as solid fuel, ecological advantages and comparatively low biomass production costs. Materials and Methods: In this study, the wood of black locust Robinia pseudoacacia, white willow Salix alba L., poplars Populus deltoides and Populus x euramericana cl.I-214, aged eight years were examined. Immediately after the felling, sample discs were taken to assess moisture content, ash content, the width of growth rings, wood densities and calorific values, according to the standard methodology. Results:The mean values of willow, poplar and black locust wood density were 341 kg/m3, 336 kg/m3 and 602 kg/m3,respectively. The average heating values of willow poplar and black locust wood were 18.599 MJ/kg, 18.564 MJ/kg and 21.196 MJ/kg, respectively. The FVI index (average values was higher for black locust (17.186 than for poplar and willow clones, which were similar: 11.312 and 11.422 respectively. Conclusions: Black locust wood with a higher density, calorific value and ash content compared to poplar and willow wood proved to be a more suitable raw material as RES. However, it is very important, from the aspect of the application of wood of these tree species as RES, to also consider the influence of the biomass yield per unit area of the plantations established as “energy plantations”.

  2. STATISTICAL ANALYSIS OF RAW SUGAR MATERIAL FOR SUGAR PRODUCER COMPLEX

    A. A. Gromkovskii; O. I. Sherstyuk

    2015-01-01

    Summary. In the article examines the statistical data on the development of average weight and average sugar content of sugar beet roots. The successful solution of the problem of forecasting these raw indices is essential for solving problems of sugar producing complex control. In the paper by calculating the autocorrelation function demonstrated that the predominant trend component of the growth raw characteristics. For construct the prediction model is proposed to use an autoregressive fir...

  3. Theoretical backgrounds of non-tempered materials production based on new raw materials

    Lesovik, V. S.; Volodchenko, A. A.; Glagolev, E. S.; Chernysheva, N. V.; Lashina, I. V.; Feduk, R. S.

    2018-03-01

    One of the trends in construction material science is development and implementation of highly effective finish materials which improve architectural exterior of cities. Silicate materials widely-used in the construction today have rather low decorative properties. Different coloring agents are used in order to produce competitive materials, but due to the peculiarities of the production, process very strict specifications are applied to them. The use of industrial wastes or variety of rock materials as coloring agents is of great interest nowadays. The article shows that clay rock can be used as raw material in production of finish materials of non-autoclaved solidification. This raw material due to its material composition actively interacts with cementing component in steam treatment at 90–95 °C with formation of cementing joints that form a firm coagulative-cristalized and crystallization structure of material providing high physic-mechanical properties of silicate goods. It is determined that energy-saving, colored finish materials with compression strength up to 16 MPa can be produced from clay rocks.

  4. 90Y production of high purity by electrochemical separation

    Alberti Ramírez, Alejandro; Serra Águila, Rolando; Morín Zorrilla, José Antonio; Pino Peraza, Madián; Soler Iglesias, Joel; Cruz Morales, Amed

    2016-01-01

    In this paper 90 Y is obtained without added carrier, by electrolytic separation from a solution in secular equilibrium Sr-Y and further purification in three cycles electrolytic automated, at constant current. The process productivity was 60-80 mCi (2220-2960 MBq). The long half-life of 90 Sr to be used by virtually indefinitely ensuring the stability of the raw material for generator operation, which helps sustainability and production stability. In 18 productions to date could be found to both content of 90 Sr equal to 0.110 ± 0.004 (k = 2) kBq / g by various methods, for their ability combination with DTPA, bifunctional chelate appropriate range of concentrations and even in the presence of trace metals, resulting in excellent characteristics for use as precursor in the preparation of therapeutic radiopharmaceuticals including radioimmunotherapy. The latter being a pure beta emitter with physical half-life, comparable to the time of capture and residence of many antibodies in tumors. The influence of Fe (III) was studied by the method of addition and concluded that only affects the performance of DTPA 90 Y marking if their presence is above a concentration of 0.018 mol / L. We show that the presence of other metals such as Pb (II), Zn (II) and Cu (II) also affects performance complexation

  5. A High-Purity Alumina for Use in Studies of Shock Loaded Samples

    Lacina, David; Neel, Christopher

    2017-06-01

    We report the results of plate impact experiments on a potential new ``standard'' material, Coorstek Plasmapure-UC (99.9% purity) polycrystalline alumina, for use in non-conduction, impact environment, shock loading studies. This work was motivated by a desire to find a 99.9% purity alumina to replace the now unavailable Coors Vistal (99.9%) alumina, as it was hoped the Hugoniot elastic limit (HEL) of the new standard would match the 9-11 GPa value of Vistal. Shock response data, including the HEL, Hugoniot particle velocities, Hugoniot shock velocities, stress vs volume, and release wave speeds, was obtained up to 14 GPa. This data will be compared with Hugoniot curve data for other high purity alumina to contrast differences in the shock response, and is intended to be useful in impedance matching calculations. We will show that the HEL of Plasmapure-UC alumina is 5.5 GPa and speculate on causes for this lower than expected value. We will also explore why the elastic-plastic response for Plasmapure-UC alumina differs from what has been observed from other high purity alumina. The final result of this work is to recommend a well-characterized, lower purity alumina (Coorstek AD-995) as a potential new ``standard'' material.

  6. Automation of the Characterization of High Purity Germanium Detectors

    Dugger, Charles ``Chip''

    2014-09-01

    Neutrinoless double beta decay is a rare hypothesized process that may yield valuable insight into the fundamental properties of the neutrino. Currently there are several experiments trying to observe this process, including the Majorana DEMONSTRAOR experiment, which uses high purity germanium (HPGe) detectors to generate and search for these events. Because the event happens internally, it is essential to have the lowest background possible. This is done through passive detector shielding, as well as event discrimination techniques that distinguish between multi-site events characteristic of gamma-radiation, and single-site events characteristic of neutrinoless double beta decay. Before fielding such an experiment, the radiation response of the detectors must be characterized. A robotic arm is being tested for future calibration of HPGe detectors. The arm will hold a source at locations relative to the crystal while data is acquired. Several radioactive sources of varying energy levels will be used to determine the characteristics of the crystal. In this poster, I will present our work with the robot, as well as the characterization of data we took with an underground HPGe detector at the WIPP facility in Carlsbad, NM (2013). Neutrinoless double beta decay is a rare hypothesized process that may yield valuable insight into the fundamental properties of the neutrino. Currently there are several experiments trying to observe this process, including the Majorana DEMONSTRAOR experiment, which uses high purity germanium (HPGe) detectors to generate and search for these events. Because the event happens internally, it is essential to have the lowest background possible. This is done through passive detector shielding, as well as event discrimination techniques that distinguish between multi-site events characteristic of gamma-radiation, and single-site events characteristic of neutrinoless double beta decay. Before fielding such an experiment, the radiation response of

  7. CAN BE BLUEBERRIES THE RISK FOOD AND RAW MATERIAL?

    Michal Medvecký2

    2012-02-01

    Full Text Available Fruits of the highbush blueberries are popular for their beneficial effects on human health and for their excellent sweet-vine taste. Our work is focused on risk assessment of selected elements in relation to the content of bioactive compounds in wild and cultivated of highbush blueberries (Vaccinium corymbosum L.. Anthocyanins are polyphenols that are widely distributed in plants, and contribute to the brilliant blue, red or purple colour in leaves, flowers or fruits. In the samples the antioxidant capacity by the method of Brand – Williams using DPPH (2,2–difenyl-1-pikrylhydrazyl and the content of anthocyanins by the modified method Lapornik in two samples of wild blueberries from different areas of Slovakia (Čertovica and Oravské Veselé and in 6 cultivated varieties highbush blueberry (Bluejay, Bluecrop, Patriot, Berkeley, Brigitta, Nelson were determined. The contents of risky elements - Cd, Pb were assessed by AAS method. The contents of Pb were in all observed samples higher than the maximum limit given by the legislation (cultivated: 0.5612 – 0.9912 mg.kg-1, wild: 0.792 – 0.874 mg.kg-1. The measured content values of Cd were in all samples of blueberries lower than hygienic limit. The highest content of anthocyanins from analysed samples was in wild blueberries from surrouding Čertovica 4870.125 ± 22.803 mg.dm-3, but in this sample was simultaneously the lowest antioxidant capacity of 61.15 ± 1.002 %. The highest antioxidant capacity was measured in sample of cultivated variety Bluejay 87.175 ± 0.45 %. It is important to carry out monitoring of heavy metals to consumption of safe food raw materials and foodstuffs.

  8. Microalgae as a raw material for biofuels production.

    Gouveia, Luisa; Oliveira, Ana Cristina

    2009-02-01

    Biofuels demand is unquestionable in order to reduce gaseous emissions (fossil CO(2), nitrogen and sulfur oxides) and their purported greenhouse, climatic changes and global warming effects, to face the frequent oil supply crises, as a way to help non-fossil fuel producer countries to reduce energy dependence, contributing to security of supply, promoting environmental sustainability and meeting the EU target of at least of 10% biofuels in the transport sector by 2020. Biodiesel is usually produced from oleaginous crops, such as rapeseed, soybean, sunflower and palm. However, the use of microalgae can be a suitable alternative feedstock for next generation biofuels because certain species contain high amounts of oil, which could be extracted, processed and refined into transportation fuels, using currently available technology; they have fast growth rate, permit the use of non-arable land and non-potable water, use far less water and do not displace food crops cultures; their production is not seasonal and they can be harvested daily. The screening of microalgae (Chlorella vulgaris, Spirulina maxima, Nannochloropsis sp., Neochloris oleabundans, Scenedesmus obliquus and Dunaliella tertiolecta) was done in order to choose the best one(s), in terms of quantity and quality as oil source for biofuel production. Neochloris oleabundans (fresh water microalga) and Nannochloropsis sp. (marine microalga) proved to be suitable as raw materials for biofuel production, due to their high oil content (29.0 and 28.7%, respectively). Both microalgae, when grown under nitrogen shortage, show a great increase (approximately 50%) in oil quantity. If the purpose is to produce biodiesel only from one species, Scenedesmus obliquus presents the most adequate fatty acid profile, namely in terms of linolenic and other polyunsaturated fatty acids. However, the microalgae Neochloris oleabundans, Nannochloropsis sp. and Dunaliella tertiolecta can also be used if associated with other

  9. Exploring China's materialization process with economic transition: analysis of raw material consumption and its socioeconomic drivers.

    Wang, Heming; Tian, Xin; Tanikawa, Hiroki; Chang, Miao; Hashimoto, Seiji; Moriguchi, Yuichi; Lu, Zhongwu

    2014-05-06

    China's rapidly growing economy is accelerating its materialization process and thereby creating serious environmental problems at both local and global levels. Understanding the key drivers behind China's mass consumption of raw materials is thus crucial for developing sustainable resource management and providing valuable insights into how other emerging economies may be aiming to accomplish a low resource-dependent future. Our results show that China's raw material consumption (RMC) rose dramatically from 11.9 billion tons in 1997 to 20.4 billion tons in 2007, at an average annual growth rate at 5.5%. In particular, nonferrous metal minerals and iron ores increased at the highest rate, while nonmetallic minerals showed the greatest proportion (over 60%). We find that China's accelerating materialization process is closely related to its levels of urbanization and industrialization, notably demand for raw materials in the construction, services, and heavy manufacturing sectors. The growing domestic final demand level is the strongest contributor of China's growth in RMC, whereas changes in final demand composition are the largest contributors to reducing it. However, the expected offsetting effect from changes in production pattern and production-related technology level, which should be the focus of future dematerialization in China, could not be found.

  10. Comparison of Biochars Characteristics from Different Raw Materials

    SUN Tao

    2017-10-01

    Full Text Available Biochar is the carbon-rich product from biomass under limited supply of oxygen. Biochar has been well recognized in enhancing terrestrial carbon sequestration and greenhouse gas mitigation as well as in improving soil fertility and plant productivity. To explore the differences of biochars produced from different raw materials, six biochar samples made from alfalfa straw, wheat straw, cotton straw, grape vines, sludge and lignite were selected as test material. Qualitative and quantitative analysis by fourier transform infrared spectroscopy(FTIR and Boehm titration were used to determine the amount of the surface functional groups of biochars. Meanwhile the scanning electron microscopy(SEM was used to characterize the surface morphology of biochar samples. In addition, the basic physicochemical characteristics of biochar samples, such as pH value, organic carbon content and cation exchange capacity were also determined. The results showed that all of the biochar were alkaline except the sludge biochar was acidic. The organic carbon content of alfalfa biochar was the highest(588.43 g·kg-1 and sludge biochar was the lowest(168.17 g·kg-1. Furthermore, the rank of cation exchange capacity was alfalfa straw biochar, cotton straw biochar > grape vine biochar > wheat straw biochar > sludge biochar > lignite biochar. FTIR spectrum showed that there were the aromatic hydrocarbon and the oxygen group on the surface of biochar and the structure of biochar was mainly based on the aromatic rings skeleton. The total functional groups content of alfalfa straw biochar was the highest, but that of sludge biochar was the lowest. The SEM results showed that there were obvious pore structure on the surface of plant-based biochar, but none on the surface of mineral-based biochar. Alfalfa straw biochar, wheat straw biochar, cotton straw biochar and grape vine biochar can be applied to improve farmland soil quality and increase soil fertility, and lignite biochar

  11. Synthesis of High Purity Nonsymmetric Dialkylphosphinic Acid Extractants.

    Wang, Junlian; Xie, Meiying; Liu, Xinyu; Xu, Shengming

    2017-10-19

    We present the synthesis of (2,3-dimethylbutyl)(2,4,4'-trimethylpentyl)phosphinic acid as an example to demonstrate a method for the synthesis of high purity nonsymmetric dialkylphosphinic acid extractants. Low toxic sodium hypophosphite was chosen as the phosphorus source to react with olefin A (2,3-dimethyl-1-butene) to generate a monoalkylphosphinic acid intermediate. Amantadine was adopted to remove the dialkylphosphinic acid byproduct, as only the monoalkylphosphinic acid can react with amantadine to form an amantadine∙mono-alkylphosphinic acid salt, while the dialkylphosphinic acid cannot react with amantadine due to its large steric hindrance. The purified monoalkylphosphinic acid was then reacted with olefin B (diisobutylene) to yield nonsymmetric dialkylphosphinic acid (NSDAPA). The unreacted monoalkylphosphinic acid can be easily removed by a simple base-acid post-treatment and other organic impurities can be separated out through the precipitation of the cobalt salt. The structure of the (2,3-dimethylbutyl)(2,4,4'-trimethylpentyl)phosphinic acid was confirmed by 31 P NMR, 1 H NMR, ESI-MS, and FT-IR. The purity was determined by a potentiometric titration method, and the results indicate that the purity can exceed 96%.

  12. The determination of boron in aluminium of high purity

    Cook, E.B.T.; Holan, H.

    1977-01-01

    A description is given of the investigations that led to the development of chemical methods for the determination of boron within the range 0,25 to 1,0 p.p.m. in aluminium of high purity. Methods were developed that incorporated fluorimetry, directly in solutions containing aluminium and after separation of boron by liquid-liquid extraction into 2-ethyl-1,3 hexanediol. A published spectrophotometric method, involving extraction of the BF 4 sup(-) complex with methylene blue into dichloroethane, was modified for application to alluminium samples. Details of this modified procedure and the fluorimetric-extraction procedure are appended. The precision of the methylene-blue method is about 6 percent relative and is recommended for precision and speed in preference to others. Separation of boron by distillation and spectrophotometric determination with curcumin gave low values in comparison with those obtained by the other methods. Agreement between the boron values obtained on the samples tested was good for the fluorimetric and methylene-blue spectrophotometric methods

  13. Spectroscopic Determination of Trace Contaminants in High Purity Oxygen

    Hornung, Steven D.

    2011-01-01

    Oxygen used for extravehicular activities (EVA) must be free of contaminants because a difference in a few tenths of a percent of argon or nitrogen content can mean significant reduction in available EVA time. These inert gases build up in the extravehicular mobility unit because they are not metabolized or scrubbed from the atmosphere. Measurement of oxygen purity above 99.5% is problematic, and currently only complex instruments such as gas chromatographs or mass spectrometers are used for these determinations. Because liquid oxygen boil-off from the space shuttle will no longer be available to supply oxygen for EVA use, other concepts are being developed to produce and validate high purity oxygen from cabin air aboard the International Space Station. A prototype optical emission technique capable of detecting argon and nitrogen below 0.1% in oxygen was developed at White Sands Test Facility. This instrument uses a glow discharge in reduced pressure gas to produce atomic emission from the species present. Because the atomic emission lines from oxygen, nitrogen, and argon are discrete and in many cases well-separated, trace amounts of argon and nitrogen can be detected in the ultraviolet and visible spectrum. This is a straightforward, direct measurement of the target contaminants and may lend itself to a device capable of on-orbit verification of oxygen purity. System design and optimized measurement parameters are presented.

  14. Spall behaviors of high purity copper under sweeping detonation

    Yang, Yang, E-mail: yangyanggroup@163.com [School of Material Science and Engineering, Central South University, Changsha 410083 (China); Institute of Fluid Physics, China Academy of Engineering Physics, Mianyang 621900 (China); National Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081 (China); Key Laboratory of Nonferrous Metals Material Science and Engineering of Ministry of Education, Central South University, Changsha 410083 (China); Zhi-qiang, Peng; Xing-zhi, Chen [School of Material Science and Engineering, Central South University, Changsha 410083 (China); Key Laboratory of Nonferrous Metals Material Science and Engineering of Ministry of Education, Central South University, Changsha 410083 (China); Zhao-liang, Guo; Tie-gang, Tang; Hai-bo, Hu [Institute of Fluid Physics, China Academy of Engineering Physics, Mianyang 621900 (China); Qing-ming, Zhang [National Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081 (China)

    2016-01-10

    Suites of sweeping detonation experiments were conducted to assess the spall behavior of high purity copper samples with different heat treatment histories. Incipient spall samples were obtained at different sweeping detonation condition. Metallographic and Electron Backscattered Diffraction (EBSD) analyses were performed on the soft-recovered samples. The effects of grain boundaries, grain size, crystal orientation and loading direction on the spall behaviors were discussed. Spall plane branching was found in the main spall plane of the damage samples. For similar microstructure, the area of voids increase with the increase of shock stress, and the coalescence of voids also become more obvious. Results from EBSD analysis show that the grain sizes were decreased and the grains were elongated along the direction of the plate width. Triple junctions composed of two or more general high angle boundaries are the preferred locations for intergranular damage. Voids prefer to nucleate in the grain boundaries composed of grain with high Taylor Factor (TF) than other grains. The damage areas in the grains with high TF are more severe. Boundaries close to perpendicular to the loading direction are more susceptible to void nucleation than the boundaries close to parallel to the loading direction, but the difference of voids nucleated in these two boundaries is less significant than the results obtained by plate impact experiment. It would be caused by the obliquity between the shock loading direction and the plate normal.

  15. Irradiation as an alternative environmentally friendly method for microbiological decontamination of herbal raw material

    Dragusin, M.; Rotaru, R.

    2000-01-01

    Microbiological contamination of herbal raw materials is a serious problem in the production of therapeutical preparations. A good quality of the product, according to the pharmaceutical requirements may be achieved by applying suitable methods of decontamination. The decontamination treatments should be fast and effective against all microorganisms. It should ensure the decontamination of both packaging and the microorganisms present and must not reduce the sensory and technological qualities of the commodities. Decontamination of herbal raw materials by irradiation is a method by choice. It is because chemical methods are recognized recently as not safe to the consumer. Irradiation, in turn, is technically feasible, very effective and friendly enough to environment process. Under the prevailing production and handling conditions, most herbs contain a large number of microorganisms what is a serious problem in the production of therapeutical preparations. For several years the most widely used methods for decontamination of herbs was fumigation with ethylene oxide or methyl bromide. Both methods today banned in most countries. Irradiation is an alternative and safe method for effective reducing the microbial contamination of herbal raw materials. The following raw materials have been examined: Folium Cynara, Folium Plantago, Flos Chamomillae, Semen Sylibum Marianum and Folium Farfara. The content of biologically active compounds before and after irradiation of the raw materials did not change in a significant degree after irradiation. The dose of radiation for herbals raw materials was 10 kGy. There are two groups of raw materials: - The raw materials designed for preparing granulates, tablets, dragees, capsules, aqueous extracts, infusions, macerations and preparations for external use; - The raw materials assigned for preparing alcoholic preparations, isolated compounds, oil preparations and essential oils. The medical herbs and herbal raw materials before their

  16. Effect of initial grain size on dynamic recrystallization in high purity austenitic stainless steels

    El Wahabi, M.; Gavard, L.; Montheillet, F.; Cabrera, J.M.; Prado, J.M.

    2005-01-01

    The influence of initial microstructure on discontinuous dynamic recrystallization (DDRX) has been investigated by using high purity and ultra high purity austenitic stainless steels with various initial grain sizes. After uniaxial compression tests at constant strain rates and various temperatures, the steady state microstructure or the state corresponding to the maximum strain (ε = 1) attained in the test was analyzed by scanning electron microscopy aided with automated electron back scattering diffraction. Recrystallized grain size d rec and twin boundary fraction f TB measurements were carried out. The mechanical behavior was also investigated by comparing experimental stress-strain curves with various initial grain sizes. DDRX kinetics was described by the classical Avrami equation. It was concluded that larger initial grain sizes promoted a delay in the DDRX onset in the two alloys. It was also observed that the softening process progressed faster for smaller initial grain sizes. The effect of initial grain size is larger in the HP material and becomes more pronounced at low temperature

  17. Preparation of High Purity CdTe for Nuclear Detector: Electrical and Nuclear Characterization

    Zaiour, A.; Ayoub, M.; Hamié, A.; Fawaz, A.; Hage-ali, M.

    High purity crystal with controllable electrical properties, however, control of the electrical properties of CdTe has not yet been fully achieved. Using the refined Cd and Te as starting materials, extremely high-purity CdTe single crystals were prepared by the traditional vertical THM. The nature of the defects involved in the transitions was studied by analyzing the position of the energy levels by TSC method. The resolution of 4.2 keV (FWHM) confirms the high quality and stability of the detectors: TSC spectrum was in coherence with detectors spectrum with a horizontal plate between 0.2 and 0.6 eV. The enhancement in resolution of detectors with a full width at half- maximum (less than 0.31 meV), lead to confirm that the combination of vacuum distillation and zone refining was very effective to obtain more purified CdTe single crystals for photovoltaic or nuclear detectors with better physical properties.

  18. Chances for a long-term securing of the raw material supply to the FRG. Pt. 1

    1975-09-01

    The Federal Republic of Germany is almost completely dependent on raw material imports. Growing raw material consumption and an imminent increase in supply uncertainties will require intensified research and development work in the field of raw material safeguarding. Initial approaches to possible technical solutions are being indicated in connection with four raw materials (aluminium, copper, phosphate and carbon carriers). The material balances of these raw materials are shown and the technical and economic interrelations illustrated in the light of world-wide trends. It is being demonstrated that two essential objectives are to be pursued for securing raw material supplies: 1) extension of the raw material basis for primary and secondary raw materials, 2) improvement of raw material utilization in all sectors of economy. To provide a solution for the wide spectrum of tasks it will be necessary to establish adequate analytical methods and procedures. (orig.) [de

  19. Secondary raw materials for synthesising new kind of cements

    Goñi, S.

    2001-12-01

    Full Text Available The present paper is a comparative study of some characteristics of new belite cements obtained from two kind of wastes, which were used as secondary raw materials: fly ash (FA, of low CaO content, from coal combustion, and ash from incineration of municipal solid waste (MSWIA. Cements were synthesised in a range of temperature between 700°C and 900°C from MSWIA and FA, which were previously activated by hydrothermal treatment at 200°C The evolution of cemented phases with the heating temperature was followed by X-ray diffraction (XRD. The results were compared with those obtained from heating the starting FA and MSWIA without the previous hydrothermal treatment. The degree of hydration was quantitatively evaluated by the combined water content, determined from thermogravimetric analyses, during a period of 28 days or 200 days from mixing depending of hydration kinetics of each cement.

    Este trabajo es un estudio comparativo de algunas de las características de nuevos cementos belíticos, obtenidos a partir de dos tipos de residuos, como materia prima secundaria: cenizas volantes (CV de bajo contenido en cal, procedentes de la combustión del carbón y cenizas procedentes de la incineración de residuos sólidos urbanos (CIRSU. Los cementos fueron sintetizados en un rango de temperaturas comprendido entre 700°C y 900°C después de un tratamiento hidrotermal de la CV y CIRSU a 200°C La evolución de las fases cementicias, con la temperatura de calentamiento, fue estudiada por difracción de rayos X (DRX. Los resultados fueron comparados con aquellos obtenidos, directamente, por calentamiento de los residuos, sin un tratamiento hidrotermal previo de los mismos. El grado de hidratación fue cuantitativamente evaluado, por medio del análisis termogravimétrico, a partir del agua combinada de los cementos hidratados durante un período de 28 días o 200 días, dependiendo de la cinética de hidratación de cada cemento.

  20. Characterization of Lignocellulosic Biomass as Raw Material for the Production of Porous Carbon-based Materials

    Saptadi Darmawan

    2016-02-01

    Full Text Available Lignocellulosic biomass is a potential raw material that can be used in the synthesis (manufacture of porous carbon stuffs. The properties of such porous carbon products are affected by the species of the raw material and the manufacturing process, among other things. This paper scrutinizes the related characteristics of lignocellulosic raw materials that indicate potential for the production of porous carbon. Three species were used: pine (Pinus merkusii wood, mangium (Acacia mangium wood, and candlenut (Aleurites moluccana shells, representing softwoods, hardwoods, and non-wood stuffs, respectively. Analyses of their chemical compounds and proximate contents were carried out. Additionally, nano scale scrutiny of the lignocellulosic biomass was also conducted using the nano capable instruments, which consisted of SEM, EDS, XRD, FTIR, and DSC. Results revealed that pine wood had the most potential to produce porous carbon. Morphologically, pine wood afforded the best permeability, whereby at the structure of monoclinic cellulose crystals, there were cellulose-I(alpha structures, which contained less cellulose-I(beta structures. Furthermore, pine wood exhibited greater volatile matter content, as confirmed through the FTIR, which greatly assisted the forming of porosity inside its corresponding carbon.

  1. Mesophase Formation Stabilizes High-purity Magic-sized Clusters

    Nevers, Douglas R.; Williamson, Curtis B.; Savitzky, Benjamin H; Hadar, Ido; Banin, Uri; Kourkoutis, Lena F.; Hanrath, Tobias; Robinson, Richard D.

    2018-01-01

    Magic-sized clusters (MSCs) are renowned for their identical size and closed-shell stability that inhibit conventional nanoparticle (NP) growth processes. Though MSCs have been of increasing interest, understanding the reaction pathways toward their nucleation and stabilization is an outstanding issue. In this work, we demonstrate that high concentration synthesis (1000 mM) promotes a well-defined reaction pathway to form high-purity MSCs (>99.9%). The MSCs are resistant to typical growth and dissolution processes. Based on insights from in-situ X-ray scattering analysis, we attribute this stability to the accompanying production of a large, hexagonal organic-inorganic mesophase (>100 nm grain size) that arrests growth of the MSCs and prevents NP growth. At intermediate concentrations (500 mM), the MSC mesophase forms, but is unstable, resulting in NP growth at the expense of the assemblies. These results provide an alternate explanation for the high stability of MSCs. Whereas the conventional mantra has been that the stability of MSCs derives from the precise arrangement of the inorganic structures (i.e., closed-shell atomic packing), we demonstrate that anisotropic clusters can also be stabilized by self-forming fibrous mesophase assemblies. At lower concentration (<200 mM or >16 acid-to-metal), MSCs are further destabilized and NPs formation dominates that of MSCs. Overall, the high concentration approach intensifies and showcases inherent concentration-dependent surfactant phase behavior that is not accessible in conventional (i.e., dilute) conditions. This work provides not only a robust method to synthesize, stabilize, and study identical MSC products, but also uncovers an underappreciated stabilizing interaction between surfactants and clusters.

  2. Mesophase Formation Stabilizes High-purity Magic-sized Clusters

    Nevers, Douglas R.

    2018-01-27

    Magic-sized clusters (MSCs) are renowned for their identical size and closed-shell stability that inhibit conventional nanoparticle (NP) growth processes. Though MSCs have been of increasing interest, understanding the reaction pathways toward their nucleation and stabilization is an outstanding issue. In this work, we demonstrate that high concentration synthesis (1000 mM) promotes a well-defined reaction pathway to form high-purity MSCs (>99.9%). The MSCs are resistant to typical growth and dissolution processes. Based on insights from in-situ X-ray scattering analysis, we attribute this stability to the accompanying production of a large, hexagonal organic-inorganic mesophase (>100 nm grain size) that arrests growth of the MSCs and prevents NP growth. At intermediate concentrations (500 mM), the MSC mesophase forms, but is unstable, resulting in NP growth at the expense of the assemblies. These results provide an alternate explanation for the high stability of MSCs. Whereas the conventional mantra has been that the stability of MSCs derives from the precise arrangement of the inorganic structures (i.e., closed-shell atomic packing), we demonstrate that anisotropic clusters can also be stabilized by self-forming fibrous mesophase assemblies. At lower concentration (<200 mM or >16 acid-to-metal), MSCs are further destabilized and NPs formation dominates that of MSCs. Overall, the high concentration approach intensifies and showcases inherent concentration-dependent surfactant phase behavior that is not accessible in conventional (i.e., dilute) conditions. This work provides not only a robust method to synthesize, stabilize, and study identical MSC products, but also uncovers an underappreciated stabilizing interaction between surfactants and clusters.

  3. Trace radioactive measurement in foodstuffs using high purity germanium detector

    Morco, Ryan P.; Racho, Joseph Michael D.; Castaneda, Soledad S.; Almoneda, Rosalina V.; Pabroa, Preciosa Corazon B.; Sucgang, Raymond J.

    2010-01-01

    Trace radioactivity in food has been seriously considered sources of potential harm after the accidental radioactive releases in the last decades which led to contamination of the food chain. Countermeasures are being used to reduce the radiological health risk to the population and to ensure that public safety and international commitments are met. Investigation of radioactive traces in foods was carried out by gamma-ray spectrometry. The radionuclides being measured were fission products 1 37Cs and 1 34Cs and naturally occurring 4 0Κ. Gamma-ray measurements were performed using a hybrid gamma-ray counting system with coaxial p-type Tennelec High Purity Germanium (HPGe) detector with relative efficiency of 18.4%. Channels were calibrated to energies using a standard check source with 1 37Cs and 6 0Co present. Self-shielding within samples was taken into account by comparing directly with reference standards of similar matrix and geometry. Efficiencies of radionuclides of interests were accounted in calculating the activity concentrations in the samples. Efficiency calibration curve was generated using an in-house validated program called FINDPEAK, a least-square method that fits a polynomial up to sixth-order of equation. Lower Limits of Detection (LLD) obtained for both 1 37Cs and 1 34Cs ranges from 1-6 Bq/Kg depending on the sample matrix. In the last five years, there have been no foodstuffs analyzed exceeded the local and international regulatory limit of 1000Bq/Kg for the summed activities of 1 37Cs and 1 34Cs. (author)

  4. Traceability System Model for Quality Gelatin Raw Material of Cattle Hides

    S Nur

    2010-09-01

    Full Text Available Several criteria must be accomplished within the provision of quality products in terms of the types of materials, the processing methods and effort to get it. Traceability system involves various parties that have different needs and goals in the process of supplying raw materials. Hence, there is a need for institutional systems engineering that can organize and manage the tracking process, the procurement of raw materials that guarantee the origin of gelatin raw materials, and facilitate the industry and customer to create a standardized quality of product. The purpose of the study formulates the institutional tracking models of gelatin raw material from cattle hide based on various criteria and assessment of the expert opinion. The methods used in this study were Interpretative structural modeling to formulate a representation of institutional tracking efficiently and analytical hierarchy process to determine the tracking strategy of industrial gelatin raw materials from cowhide. The results obtained from the study were some key elements of institutional tracking model for industrial gelatin raw materials from cowhide and the traceability strategies for industrial raw materials from cattle hide gelatin Indonesia. (Animal Production 12(3: 190-198 (2010 Key Words: traceability, institutional model, cattle hide, gelatin

  5. Raw materials for the energy supply of the future. Geology, markets, environmental influences

    Hagelueken, Christian; Thauer, Rudolf K.; Buchholz, Peter; Gutzmer, Jens; Littke, Ralf; Angerer, Gerhard; Wellmer, Friedrich-Wilhelm

    2015-01-01

    More and more metals are needed to expand modern energy technologies, but we can not completely dispense with fossil raw materials and biomass in the near future either. Are the incidence of the conversion of energy sources sufficient? The analysis of the academy project ''Energy Systems of the Future'' (ESYS) comes to the conclusion that geologically enough raw materials are available. The challenge, however, is to make the supply safe, affordable and environmentally and socially compatible. The analysis explains the mechanisms of action on the global commodity markets and identifies supply risks. These include, for example, sudden demand on the international markets as well as the unequal distribution of the world's raw material reserves. This is followed by the analysis approaches, in order to recognize warning signals for potential raw material bottlenecks in time, to develop evasive strategies and to secure the raw material supply for the energy turnarounds. For example, the expansion of recycling can help to reduce the dependence on metal imports. In mining, on the other hand, innovative technologies have to be developed in order to improve the exploration and utilization of the deposits. By establishing binding environmental and social standards, the extraction of raw materials could also become more sustainable. The analysis also highlights the importance of bioenergy and fossil raw materials, such as oil and natural gas, for energy generation. The authors describe the advantages and disadvantages of these energy carriers and the measures that can be used to reduce environmental pollution such as greenhouse gas emissions. [de

  6. Technological project of serpentine raw material milling from Dobšiná heaps

    Alena Pietriková

    2005-11-01

    Full Text Available Serpentine heaps in the surrounding of Dobšiná are an old ecological problem of the city and at the same time a suitable material for the production of MgCl2 and SiO2. The technology of the production is based on the chemical processing of the raw material, which is preceded by the raw material preparation comprising of the mechanical and hydraulic sorting, milling and the magnetic separation operations.

  7. A light hydrocarbon fuel processor producing high-purity hydrogen

    Löffler, Daniel G.; Taylor, Kyle; Mason, Dylan

    This paper discusses the design process and presents performance data for a dual fuel (natural gas and LPG) fuel processor for PEM fuel cells delivering between 2 and 8 kW electric power in stationary applications. The fuel processor resulted from a series of design compromises made to address different design constraints. First, the product quality was selected; then, the unit operations needed to achieve that product quality were chosen from the pool of available technologies. Next, the specific equipment needed for each unit operation was selected. Finally, the unit operations were thermally integrated to achieve high thermal efficiency. Early in the design process, it was decided that the fuel processor would deliver high-purity hydrogen. Hydrogen can be separated from other gases by pressure-driven processes based on either selective adsorption or permeation. The pressure requirement made steam reforming (SR) the preferred reforming technology because it does not require compression of combustion air; therefore, steam reforming is more efficient in a high-pressure fuel processor than alternative technologies like autothermal reforming (ATR) or partial oxidation (POX), where the combustion occurs at the pressure of the process stream. A low-temperature pre-reformer reactor is needed upstream of a steam reformer to suppress coke formation; yet, low temperatures facilitate the formation of metal sulfides that deactivate the catalyst. For this reason, a desulfurization unit is needed upstream of the pre-reformer. Hydrogen separation was implemented using a palladium alloy membrane. Packed beds were chosen for the pre-reformer and reformer reactors primarily because of their low cost, relatively simple operation and low maintenance. Commercial, off-the-shelf balance of plant (BOP) components (pumps, valves, and heat exchangers) were used to integrate the unit operations. The fuel processor delivers up to 100 slm hydrogen >99.9% pure with <1 ppm CO, <3 ppm CO 2. The

  8. Importance and possibilities of secondary cycles (recycling), substitution and innovation in mineral raw and primary material supply

    1980-01-01

    Part 1-4 of the series ''The basis of raw materials supply'' is intended to bring about a better understanding of the ''Concept for the supply of Austria with mineral raw- and primary materials''. Part 3 deals with recovery of raw material from old- and waste material as an important contribution to an extension of the supply's basis and to an improvement of raw material utilization.

  9. Radiochemical neutron activation analysis based multi-elemental analysis of high purity gallium

    Tashimova, F.A.; Sadikov, I.I; Salimov, M.I.; Zinov'ev, V.G.

    2006-01-01

    Full text: Gallium is one of the widely used materials in semiconductor and optoelectronics industry. Gallium is used to produce infrared detectors, piezoelectric sensors, high- and low-temperature transistors for space and defense technology. One of the most important requirements for semiconductor materials of gallium compounds is an excessive high purity for layers and films. Information on impurities (type of an impurity, concentration, character of distribution) is important as for better understanding of the physical and chemical processes taking place in formed semiconductor structures and for the 'know-how' of devices on their basis. The object of this work is to develop radiochemical neutron activation technique for analysis of high purity gallium. Irradiation of 0.1 g of gallium sample in neutron flux of 5·10 13 cm -2 s -1 for 5 hours will result in induced activity of more than 10 8 Bq, due to 72 Ga radionuclide, half-life of which is 14.1 hours. Therefore to perform instrumental NAA of gallium long period (10 day) cooling is required, and high sensitive determination of elements producing short- and long-lived radionuclides (T 1/2 72 Ga. We have studied the behavior of gallium in extraction-chromatographic system 'TBP-HCl'. The experiments have shown that higher factor of distribution (D) and capacity on gallium can be achieved when 'TBP-4M HCl' system is used. However more than 10 trace elements have high D and thus they cannot be separated from 72 Ga. To resolve the problem and increase the number of separated trace elements we have used preliminary satisfaction of chromatographic column with tellurium, which has D higher than the most of elements in 'TBP-4M HCl' system and thus suppresses extraction of elements. Distribution profile of gallium along the column and elution curve of 25 trace elements have been measured. Chemical yields of separated elements measured by using radiotracers are more than 93%. On the basis of the carried out researches

  10. Globalization and its influence to the availability of the Raw material sources

    Vodzinský Vladimír

    2002-12-01

    Full Text Available Process of globalization does not lead only to concentration of physical and financial capital, and to centralization of its managing, what can be considered as its main signs, but at same time it gives whole raw of new claims to realization of technologies and their material basis.One of very important claims is also change in structure and volume of raw materials, that is gradually viewing in increased change from consumption of so-called classical raw materials, without which it is not possible to create basic components of information technologies.Information technologies are then creating important basis for quickly developed new branches of economy.

  11. Quantitative analysis of raw materials mining of Sverdlovsk region in Russia

    Tarasyev, Alexander M.; Vasilev, Julian; Turygina, Victoria F.

    2016-06-01

    The purpose of this article is to show the application of some qualitative methods for the analysis of a dataset for raw materials. The main approaches used are related to the correlation analysis and forecasting with trend lines. It is proved that the future mining of particular ores can be predicted on the basis of mathematical modeling. It is also shown that there exists a strong correlation between the mining of some specific raw materials. Some of the revealed correlations have meaningful explanations, and for others one should look for sophisticated interpretations. The applied approach can be used for forecasting of raw materials exploitation in various regions of Russia and in other countries.

  12. INTRAW, the EU Observatory for raw materials: fostering international cooperation and developing new opportunities

    Correia, Victor; Allington, Ruth; Keane, Christopher

    2016-04-01

    A secure supply of raw materials is a European priority that extends beyond country borders and national policies. Recent European initiatives have pioneered the development of an EU strategy on raw materials emphasizing the concept of the "added value chain", which continues to pursue the three pillar strategy to: (1) ensure the fair and sustainable supply of raw materials from international markets, promoting international cooperation with developed and developing countries; (2) foster sustainable supply of raw materials from European sources, and (3) reduce consumption of primary raw materials by increasing resource efficiency and promoting recycling. This contribution presents the Horizon 2020 funded project INTRAW, the objective of which is to establish the European Union's International Observatory for Raw Materials. The creation and maintenance of the European Union's International Observatory for Raw Materials is designed to have a strong impact in two dimensions: 1. To narrow the existing gap in aspects of the raw materials knowledge infrastructure in the EU by providing a link with the same knowledge infrastructure in technologically advanced reference countries. This should contribute to the harmonization of mineral policies all over the EU, by providing data that enables evidence-based policies and appropriate, cost-effective management, planning and adaptation decisions by the public sector. This will benefit businesses, industry and society. The Observatory will also provide to policy makers in the EU and its Member States the data they need to facilitate discussion in multilateral forums. 2. To enable a better alignment of the R&I activities among the individual EU members and international cooperation countries AND between the European Union and international cooperation countries by boosting synergies with international research and innovation programmes. This way the EU's role and scientific capabilities in the raw materials area will be

  13. Annual report 2005 General Direction of the Energy and raw materials

    2005-01-01

    This 2005 annual report of the DGEMP (General Direction of the Energy and the raw Materials), takes stock on the energy bill and accounting of the France. The first part presents the electric power, natural gas and raw materials market in France. The second part is devoted to the diversification of the energy resources with a special attention to the renewable energies and the nuclear energy. The third part discusses the energy and raw materials prices and the last part presents the international cooperation in the energy domain. (A.L.B.)

  14. Study of mechanoactivation of tungsten-molybdenum containing raw material in gas-jet mill

    Agnokov, T.Sh.; Gorobets, L.Zh.; Martynenko, V.P.; Fedorov, Yu.P.; Krakhmaleva, M.T.; Sokolova, L.A.

    1988-01-01

    Investigation is aimed at intensifying autoclave-soda leaching of tungsten-molybdenum-containing raw material. Connection of reactivity and physicochemical properties of crushed tungsten-molybdenum-containing products under different gas-jet crushing parameters is investigated. Optimal technological indices of hydrometallurgical reprocessing of tungsten-molybdenum-containing raw materials and products processed by gas-jet technique are given. The results obtained point out to perspectiveness of applying gas-jet technique of thermomechanical processing for intensifying and increasing the quality of tungsten- and molybdenum-containing raw materials and products of hydrometallurgical production

  15. Germanium field-effect transistor made from a high-purity substrate

    Hansen, W.L.; Goulding, F.S.; Haller, E.E.

    1978-11-01

    Field effect transistors have been fabricated on high-purity germanium substrates using low-temperature technology. The aim of this work is to preserve the low density of trapping centers in high-quality starting material by low-temperature ( 0 C) processing. The use of germanium promises to eliminate some of the traps which cause generation-recombination noise in silicon field-effect transistors (FET's) at low temperatures. Typically, the transconductance (g/sub m/) in the germanium FET's is 10 mA/V and the gate leakage can be less than 10 -12 A. Present devices exhibit a large 1/f noise component and most of this noise must be eliminated if they are to be competitive with silicon FET's commonly used in high-resolution nuclear spectrometers

  16. Simulation for photon detection in spectrometric system of high purity (HPGe) using MCNPX code

    Correa, Guilherme Jorge de Souza

    2013-01-01

    The Brazilian National Commission of Nuclear Energy defines parameters for classification and management of radioactive waste in accordance with the activity of materials. The efficiency of a detection system is crucial to determine the real activity of a radioactive source. When it's possible, the system's calibration should be performed using a standard source. Unfortunately, there are only a few cases that it can be done this way, considering the difficulty of obtaining appropriate standard sources for each type of measurement. So, computer simulations can be performed to assist in calculating of the efficiency of the system and, consequently, also auxiliary the classification of radioactive waste. This study aims to model a high purity germanium (HPGe) detector with MCNPX code, approaching the spectral values computationally obtained of the values experimentally obtained for the photopeak of 137 Cs. The approach will be made through changes in outer dead layer of the germanium crystal modeled. (author)

  17. GELATIO: a general framework for modular digital analysis of high-purity Ge detector signals

    Agostini, M; Pandola, L; Zavarise, P; Volynets, O

    2011-01-01

    GELATIO is a new software framework for advanced data analysis and digital signal processing developed for the GERDA neutrinoless double beta decay experiment. The framework is tailored to handle the full analysis flow of signals recorded by high purity Ge detectors and photo-multipliers from the veto counters. It is designed to support a multi-channel modular and flexible analysis, widely customizable by the user either via human-readable initialization files or via a graphical interface. The framework organizes the data into a multi-level structure, from the raw data up to the condensed analysis parameters, and includes tools and utilities to handle the data stream between the different levels. GELATIO is implemented in C++. It relies upon ROOT and its extension TAM, which provides compatibility with PROOF, enabling the software to run in parallel on clusters of computers or many-core machines. It was tested on different platforms and benchmarked in several GERDA-related applications. A stable version is presently available for the GERDA Collaboration and it is used to provide the reference analysis of the experiment data.

  18. GELATIO: a general framework for modular digital analysis of high-purity Ge detector signals

    Agostini, M.; Pandola, L.; Zavarise, P.; Volynets, O.

    2011-08-01

    GELATIO is a new software framework for advanced data analysis and digital signal processing developed for the GERDA neutrinoless double beta decay experiment. The framework is tailored to handle the full analysis flow of signals recorded by high purity Ge detectors and photo-multipliers from the veto counters. It is designed to support a multi-channel modular and flexible analysis, widely customizable by the user either via human-readable initialization files or via a graphical interface. The framework organizes the data into a multi-level structure, from the raw data up to the condensed analysis parameters, and includes tools and utilities to handle the data stream between the different levels. GELATIO is implemented in C++. It relies upon ROOT and its extension TAM, which provides compatibility with PROOF, enabling the software to run in parallel on clusters of computers or many-core machines. It was tested on different platforms and benchmarked in several GERDA-related applications. A stable version is presently available for the GERDA Collaboration and it is used to provide the reference analysis of the experiment data.

  19. Mining Pribram in science and technology. Proceedings of Session U - Mineral raw materials treatment

    Tomasek, J.; Vetejska, K.

    1987-01-01

    The proceedings of session ''Mineral raw materials treatment'' contain 27 papers of which only one deals with the application of nuclear technology, namely, the effect of fast electrons on the magnetic properties of the polymetallic Rudniany ore. (J.B.)

  20. Influence of stabilizer on the environment and their use as possible secondary raw material

    Jelenova, M.

    2001-01-01

    In this paper author deals with the environmental impact of coal combustion in coal fired power plants and with influence of ash and stabilizer on the environment and their use as possible secondary raw material

  1. Annual report 1997. Energies and raw materials; Rapport annuel 1997. Energies et matieres premieres

    NONE

    1998-12-31

    This report gives the important directions of French energy policy. Nuclear energy, electric power, natural gas, coal and petroleum products are reviewed. The situations and the forecasting for raw materials are also given. (N.C.)

  2. Influence of raw material properties upon critical quality attributes of continuously produced granules and tablets

    Fonteyne, Margot; Wickström, Henrika; Peeters, Elisabeth

    2014-01-01

    over a range of raw material attributes, manufacturing process options and process parameters. This fits further into the Process Analytical Technology (PAT) and Quality by Design (QbD) framework. The present study evaluates the effect of variation in critical raw material properties on the critical......-Lactose-PVP (30-67.5-2.5%) was used as model formulation. Seven different grades of theophylline were granulated. Afterward, the obtained granules were tableted. Both the characteristics of granules and tablets were determined. The results show that differences in raw material properties both affect...... quality attributes of granules and tablets, produced by a continuous from-powder-to-tablet wet granulation line. The granulation process parameters were kept constant to examine the differences in the end product quality caused by the variability of the raw materials properties only. Theophylline...

  3. Uranium in phosphorus-bearing raw materials and technological problems of its recovery

    Gorecki, H; Gorecka, H [Politechnika Wroclawska (Poland)

    1981-01-01

    A problem of uranium recovery from phosphorus-bearinq raw materials is discussed. The different methods of uranium recovery from extractive phosphoric acid are briefly described. The information on their applications in the industry is also given.

  4. Annual report 1997. Energies and raw materials; Rapport annuel 1997. Energies et matieres premieres

    NONE

    1997-12-31

    This report gives the important directions of French energy policy. Nuclear energy, electric power, natural gas, coal and petroleum products are reviewed. The situations and the forecasting for raw materials are also given. (N.C.)

  5. Occurrence of 1,4-dioxane in cosmetic raw materials and finished cosmetic products.

    Black, R E; Hurley, F J; Havery, D C

    2001-01-01

    Surveys of cosmetic raw materials and finished products for the presence of the carcinogen 1,4-dioxane have been conducted by the U.S. Food and Drug Administration since 1979. Analytical methods are described for the determination of 1,4-dioxane in ethoxylated cosmetic raw materials and cosmetic finished products. 1,4-Dioxane was isolated by azeotropic atmospheric distillation and determined by gas chromatography using n-butanol as an internal standard. A solid-phase extraction procedure based on a previously published method for the determination of 1,4-dioxane in cosmetic finished products was also used. 1,4-Dioxane was found in ethoxylated raw materials at levels up to 1410 ppm, and at levels up to 279 ppm in cosmetic finished products. Levels of 1,4-dioxane in excess of 85 ppm in children's shampoos indicate that continued monitoring of raw materials and finished products is warranted.

  6. Research and development programme of the EC in the field of raw materials 1982 to 1985

    Anon.

    1982-01-01

    Brussels: The EC Cabinet Council was presented a research and development programme in the field of raw materials for the years 1982 to 1985 which covers programmes already running and new actions as an overlapping raw material research programme of the EC. The new programme is divided up into 7 subprogrammes: I) metals and minerals (formerly: primary raw materials, II) uranium, III) ceramics, IV) wood as a renewable raw material, V) recycling of wastes (house and industry, VI) regaining of non-iron metals, VII) substitution. For the continuing of running actions and for beginning new projects in the 4 years plan, a total of 17 million ECU are to be allocated in the budget of the EC which will be used in cost sharing contracts or for coordinative projects. (orig./UA) [de

  7. Review of scientific Research results in identification of plant raw materials in food products

    GOLUBTSOVA YU. V.

    2016-01-01

    Currently, the science-based capabilities have been generated to develop and test various identification methods of food products and reveal adulteration using advanced technique and processes. This article reviews researches and developments to identify the plant raw materials in food products based on morphological, anatomic, physical and chemical test methods and the latest DNA-technologies. Review of physical, chemical, anatomic and morphological test methods to identify raw materials bot...

  8. IMPROVING THE SYSTEM OF RAW MATERIAL SUPPLY OF THE MEAT INDUSTRY

    A. M. Bukreev

    2013-01-01

    Full Text Available The article describes the characteristics of the process of improving the system raw materials supply of meat industry and presents the main factors, criteria, principles and algorithm rational distribution of the meat industry. The relevance of the research topic, in a globalized economy and Russia's accession to the WTO, caused by necessity to improve the system of raw material supply domestic enterprises and enhancing food security.

  9. Enhancement of efficiency of storage and processing of food raw materials using radiation technologies

    Gracheva, A. Yu.; Zav’yalov, M. A.; Ilyukhina, N. V.; Kukhto, V. A.; Tarasyuk, V. T.; Filippovich, V. P. [All-Russia Research Institute of Preservation Technology (Russian Federation); Egorkin, A. V.; Chasovskikh, A. V. [Research Institute of Technical Physics and Automation (Russian Federation); Pavlov, Yu. S., E-mail: rad05@bk.ru [Frumkin Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences (Russian Federation); Prokopenko, A. V., E-mail: pav14@mail.ru [National Research Nuclear University (Moscow Engineering Physics Institute) (Russian Federation); Strokova, N. E. [Moscow State University (Russian Federation); Artem’ev, S. A. [Russian Research Institute of Baking Industry (Russian Federation); Polyakova, S. P. [Russian Research Institute of Confectionery Industry (Russian Federation)

    2016-12-15

    The work is dedicated to improvement of efficiency of storage and processing of food raw materials using radiation technologies. International practice of radiation processing of food raw materials is presented and an increase in the consumption of irradiated food products is shown. The prospects of using radiation technologies for the processing of food products in Russia are discussed. The results of studies of radiation effects on various food products and packaging film by γ radiation and accelerated electrons are presented.

  10. Cellulosic pulps of cereal straws as raw material for the manufacture of ecological packaging

    Vargas González, Fátima; González, Zoilo; Sánchez, Rafael; Jiménez, Luis; Rodríguez Pascual, Alejandro

    2012-01-01

    The aim of this work was to study the potential application of four types of cereal straws: oats, maize, rapeseed, and barley, in order to obtain cellulose pulp through the Specel® process for use in the manufacture of 100% biodegradable and ecological packaging. Raw materials were chemically characterized to determine alcohol-extractives, ash, lignin, holocellulose, and α-cellulose. Cellulosic pulps obtained from raw materials were characterized to determine yield, Kappa number, and viscosit...

  11. Enhancement of efficiency of storage and processing of food raw materials using radiation technologies

    Gracheva, A. Yu.; Zav’yalov, M. A.; Ilyukhina, N. V.; Kukhto, V. A.; Tarasyuk, V. T.; Filippovich, V. P.; Egorkin, A. V.; Chasovskikh, A. V.; Pavlov, Yu. S.; Prokopenko, A. V.; Strokova, N. E.; Artem’ev, S. A.; Polyakova, S. P.

    2016-01-01

    The work is dedicated to improvement of efficiency of storage and processing of food raw materials using radiation technologies. International practice of radiation processing of food raw materials is presented and an increase in the consumption of irradiated food products is shown. The prospects of using radiation technologies for the processing of food products in Russia are discussed. The results of studies of radiation effects on various food products and packaging film by γ radiation and accelerated electrons are presented.

  12. Evolution and characterization of eggshell as a potential candidate of raw material

    T. Zaman

    Full Text Available Abstract Characterization of both uncalcined and calcined eggshells was done in this work. Raw eggshells turned out as a good source of calcite phase. Calcined eggshells had a mixture of lime and portlandite phase. A significant impact of calcination temperature on the percentage of generated phases was observed. Qualitative as well as semi-quantitative phase analysis, morphological characterization and physical property estimation was done for the produced powder. The influence of synthesized raw material on soil stabilization and biomaterial formation was further assessed. The eggshell turned out as a potential source of raw material for various sectors.

  13. Stochastic Modelling and Self Tuning Control of a Continuous Cement Raw Material Mixing System

    Hannu T. Toivonen

    1980-01-01

    Full Text Available The control of a continuously operating system for cement raw material mixing is studied. The purpose of the mixing system is to maintain a constant composition of the cement raw meal for the kiln despite variations of the raw material compositions. Experimental knowledge of the process dynamics and the characteristics of the various disturbances is used for deriving a stochastic model of the system. The optimal control strategy is then obtained as a minimum variance strategy. The control problem is finally solved using a self-tuning minimum variance regulator, and results from a successful implementation of the regulator are given.

  14. Biotechnologies for critical raw material recovery from primary and secondary sources: R&D priorities and future perspectives

    Hennebel, T.; Boon, N.; Maes, S.; Lenz, M.

    2015-01-01

    Europe is confronted with an increasing supply risk of critical raw materials. These can be defined as materials of which the risks of supply shortage and their impacts on the economy are higher compared to most of other raw materials. Within the framework of the EU Innovation Partnership on raw

  15. Mineral raw materials for power production in legislation of the Republic of Croatia

    Matisa, Z.

    1999-01-01

    According to the Constitution of the Republic of Croatia, mineral wealth is a public good of legal interest to the Republic of Croatia and enjoys its special protection. The Mining Law establishes that mineral wealth (including mineral resources that are used for power production) is the property of the Republic of Croatia. Among other mineral raw materials, this refers to mineral raw materials that are used for power production: coal, oil, natural gas, radioactive mineral raw materials and geothermal waters. These mineral resources are as almost all other mineral raw materials with the exception of geothermal waters, an unrecoverable natural resource. The right to use that natural resource may be granted only by a concession. The mining legislation provides for exploration and exploitation of mineral raw materials. Exploration of oil and gas is considered to comprise operations and testing with the aim to establish the existence, position and form of oil and natural gas deposits, their quality and quantity, as well as exploitation conditions. Exploitation of oil and natural gas is considered to comprise extraction from deposits, refining and transport, as well as disposal in geological structures. Mineral raw materials used in power production amount to 63% of national total primary energy production, and they cover 33% of total power consumption in the country. Legislation in the Republic of Croatia, which refers to exploration and exploitation of oil and natural gas, allows economic utilization of that unrecoverable natural wealth to run smoothly and in compliance with practices in our European environment. (author)

  16. Use of raw materials in the United States from 1900 through 2014

    Matos, Grecia R.

    2017-08-22

    The economic growth of an industrialized nation such as the United States requires raw materials for construction (buildings, bridges, highways, and so forth), defense, and processing and manufacture of goods and services. Since the beginning of the 20th century, the types and quantities of raw materials used have increased and changed significantly. This fact sheet quantifies the amounts of raw materials (other than food and fuel) that have been used in the U.S. economy annually for a period of 115 years, from 1900 through 2014. It provides a broad overview of the quantity (weight) of nonfood and nonfuel materials used in the economy and illustrates the use and significance of raw nonfuel minerals in particular as building blocks of society.These data have been compiled to help the public and policymakers understand the changing annual flow of raw materials put into use in the United States. Such information can be helpful in assessing the potential effects of materials use on the environment, assessing materials’ intensity of use, and examining the role that these materials play in the economy. The data presented indicate the substitution and shift in materials usage from renewable to nonrenewable materials during the 20th century. The disaggregated quantities by commodity (not shown in this fact sheet) may be tested against supply adequacy and end of life issues.

  17. Effect of Selected Alternative Fuels and Raw Materials on the Cement Clinker Quality

    Strigáč Július

    2015-11-01

    Full Text Available The article deals with the study of the effects of alternative fuels and raw materials on the cement clinker quality. The clinker quality was expressed by the content of two principal minerals alite C3S and belite C2S. The additions of alternative fuels ashes and raw materials, in principle, always increased the belite content and conversely reduced the amount of alite. The alternative fuels with high ash content were used such as the meat-bone meal, sewage sludge from sewage treatment plants and paper sludge and the used alternative raw materials were metallurgical slags - granulated blastfurnace slag, air cooled blastfurnace slag and demetallized steel slag, fluidized bed combustion fly ash and waste glass. Meat-bone meal, sewage sludge from sewage treatment plants and paper sludge were evaluated as moderately suitable alternative fuels which can be added in the amounts of 2.8 wt. % addition of meat-bone meals ash, 3.64 wt. % addition of sewage sludge ash and 3.8 wt. % addition of paper sludge ash to the cement raw mixture. Demetallised steel slag is suitable for production of special sulphate resistant cement clinker for CEM I –SR cement with addition up to 5 wt. %. Granulated blastfurnace slag is a suitable alternative raw material with addition 4 wt. %. Air cooled blastfurnace slag is a suitable alternative raw material with addition 4.2 wt. %. Waste glass is not very appropriate alternative raw material with addition only 1.16 wt. %. Fluidized bed combustion fly ash appears not to be equally appropriate alternative raw material for cement clinker burning with less potential utilization in the cement industry and with addition 3.41 wt. %, which forms undesired anhydrite CaSO4 in the cement clinker.

  18. Contamination of the cement raw material in a quarry site by seawater intrusion, Darica-Turkey

    Camur, M. Zeki; Doyuran, Vedat

    2008-02-01

    The open pit mining nearby shoreline is planned to be extended into below sea level in order to use additional reserves of the cement raw material (marl). The raw material is currently contaminated by seawater intrusion below a depth of 20 m up to the distance of 90 m from shoreline. Seawater intrusion related contamination of the material used for the cement production was investigated by means of diffusion process for the future two below sea level mining scenarios covering 43 years of period. According to the results, chloride concentrations higher than the tolerable limit of a cement raw material would be present in the material about 10-25 cm inward from each discontinuity surface, controlling groundwater flow, located between 170 and 300 m landward from the shoreline at below sea level mining depths of 0-30 m. The estimations suggest that total amounts of dilution required for the contaminated raw material to reduce its concentration level to the tolerance limit with uncontaminated raw material are about 113- to 124-fold for scenario I (13 years of below sea level mining after 30 years of above sea level mining) and about 126- to 138-fold for scenario II (43 years of simultaneous above and below sea level minings).

  19. Fracture mechanics of polymer mortar made with recycled raw materials

    Jurumenha,Marco Antonio Godoy; Reis,João Marciano Laredo dos

    2010-01-01

    The aim of this work is to show that industrial residues could be used in construction applications so that production costs as well as environmental protection can be improved. The fracture properties of polymer mortar manufactured with recycled materials are investigated to evaluate the materials behaviour to crack propagation. The residues used in this work were spent sand from foundry industry as aggregate, unsaturated polyester resin from polyethylene terephthalate (PET) as matrix and po...

  20. Decontamination of cosmetic and their raw materials by radiation

    Virzeu, D.M.

    1990-01-01

    The effects of gamma radiation over some cosmetic materials (solvent; thickening, talc, wax, vegetal oils, mineral, animal and synthetic oils, grease, emulsifying, conserving anti oxidizing and vitamin) are shown. The doses used were 20 KGy and 50 KGy, that are considered sterilizing and used in medical-surgical materials. The relation of the showed products is useful as a radio sensibility standard, but both can take as an indicator of what can be or not irradiated. (C.G.C.)

  1. Corrosion of high purity Fe-Cr-Ni alloys in 13 N boiling nitric acid

    Ohta, Joji; Mayuzumi, Masami; Kusanagi, Hideo; Takaku, Hiroshi

    1998-01-01

    Corrosion in boiling nitric acid was investigated for high purity Fe-18%Cr-12%Ni alloys and type 304L stainless steels (SS). Owing to very low impurity concentration, the solution treated high purity alloys show almost no intergranular corrosion while the type 304L SS show severe intergranular corrosion. Both in the high purity alloys and type 304L SS, aging treatments ranging from 873 K to 1073 K for 1 h enhance intergranular corrosion. During the aging treatments, impurities should be segregated to the grain boundaries. The corrosion behaviors were discussed from a standpoint of impurity segregation to grain boundaries. This study is of importance for purex reprocessing of spent fuels

  2. Fracture mechanics of polymer mortar made with recycled raw materials

    Marco Antonio Godoy Jurumenha

    2010-12-01

    Full Text Available The aim of this work is to show that industrial residues could be used in construction applications so that production costs as well as environmental protection can be improved. The fracture properties of polymer mortar manufactured with recycled materials are investigated to evaluate the materials behaviour to crack propagation. The residues used in this work were spent sand from foundry industry as aggregate, unsaturated polyester resin from polyethylene terephthalate (PET as matrix and polyester textile fibres from garment industry, producing an unique composite material fully from recycled components with low cost. The substitution of fresh by used foundry sand and the insertions of textile fibres contribute to a less brittle behaviour of polymer mortar.

  3. Micro-deformation behavior in micro-compression with high-purity aluminum processed by ECAP

    Xu Jie

    2015-01-01

    Full Text Available Ultrafine-grained (UFG materials have a potential for applications in micro-forming since grain size appears to be the dominant factor which determines the limiting size of the geometrical features. In this research, high-purity Al was processed by equal-channel angular pressing (ECAP at room temperature through 1–8 passes. Analysis shows that processing by ECAP produces a UFG structure with a grain size of ~1.3 μm and with microhardness and microstructural homogeneity. Micro-compression testing was carried out with different specimen dimensions using the annealed sample and after ECAP processing through 1–8 passes. The results show the flow stress increases significantly after ECAP processing by comparison with the annealed material. The flow stress generally reaches a maximum value after 2 passes which is consistent with the results of microhardness. The flow stress decreases with decreasing specimen diameter from 4 mm to 1 mm which demonstrates that size effects also exist in the ultrafine-grained materials. However, the deformation mechanism in ultrafine-grained pure Al changes from strain strengthening to softening by dynamic recovery by comparison with the annealed material.

  4. Raw-materials mixtures from waste of the coal industry for production of ceramic materials

    Galpern, E I [Scientific-Manufacturing Enterprise ` ` Ceramics` ` , Donetsk (Ukraine); Pashchenko, L V [Inst. of Physical, Organic and Coal Chemistry of NASU, Donetsk (Ukraine)

    1998-09-01

    The liquidation of waste dumps on the surface of mining enterprises and realization of measures by environment protection of air and aquatic basins are connected to the complex processing of mining mass. The main directions of utilization of mining rocks and coal wastes realized in Ukraine industry are: - filling of mines worked-out area by grouting solutions; - ceramic brick, porous filling materials and binding materials production; - road-making, construction of hydrostructures and industrial objects; - output of concrete items predominantly for using in mining conditions. The peculiarity of wastes using in above-mentioned fields is the possibility of their mass application in quantities commensurable with valumes of their yields. The experience of enterprises work which process mining rocks into building materials by burning method (ceramic brick, porous aggregates of concretes as aggloporite, expanded clay aggregate) has shown that unconstant and, as the rule, exceeding norms content of carbon and sulphur in the rock results to deterioration of products quality and technological factors of production. Unstability of carbon content in raw material makes the burning process hardly operated. Obtained products having residual carbon in the view of coke residue are often characterized by lower physical-mechanical characteristics. (orig./SR)

  5. Overview of Raw Materials for Oil Field Chemicals and Challenges ...

    The local content contribution to the oil industry is however presently not up to five percent. The concept of the local content development is not about awarding of contracts to Nigerians with foreign counterparts, but developing and expanding the industry for the benefit of the majority. Comparative study of the local materials ...

  6. Radioactivity of raw materials, metallurgical and casting products

    Hons, J.

    2000-01-01

    At present, the radioactive contamination of metallurgical products and initial materials represent a potential obstacle in foreign and domestic trade. It is of course an undesirable threat o the living environment on the one side and, at the same time, a new incorrectly used means for suppressing competition and forming a protection 'umbrella' of the national market to desirable imports on the other hand

  7. Cost minimization through optimized raw material quality composition

    Urs Buehlmann; R. Edward Thomas; Xiaoqui Zuo

    2011-01-01

    Lumber, a heterogeneous, anisotropic material produced from sawing logs, contains a varying number of randomly dispersed, unusable areas (defects) distributed over each boards’ surface area. Each board's quality is determined by the frequency and distribution of these defects and the board's dimension. Typically, the industry classifies lumber into five...

  8. Utilization of Iron Ore Tailings as Raw Material for Portland Cement Clinker Production

    Li Luo

    2016-01-01

    Full Text Available The cement industry has for some time been seeking alternative raw material for the Portland cement clinker production. The aim of this research was to investigate the possibility of utilizing iron ore tailings (IOT to replace clay as alumina-silicate raw material for the production of Portland cement clinker. For this purpose, two kinds of clinkers were prepared: one was prepared by IOT; the other was prepared by clay as a reference. The reactivity and burnability of raw meal, mineralogical composition and physical properties of clinker, and hydration characteristic of cement were studied by burnability analysis, differential thermal analysis, X-ray diffraction, and hydration analysis. The results showed that the raw meal containing IOT had higher reactivity and burnability than the raw meal containing clay, and the use of IOT did not affect the formation of characteristic mineralogical phases of Portland cement clinker. Furthermore, the physical and mechanical performance of two cement clinkers were similar. In addition, the use of IOT was found to improve the grindability of clinker and lower the hydration heat of Portland cement. These findings suggest that IOT can replace the clay as alumina-silicate raw material for the preparation of Portland cement clinker.

  9. CONTRIBUTION TO THE STATISTICAL INTERPRETATION OF RAW MATERIALS FOR THE CEMENT INDUSTRY OF SPLIT

    Miroslav Matijaca

    1990-12-01

    Full Text Available Up to the last two decades cement was produced from mari called »tupina« (with about 76% CaCOj which is an ideal mixture for cement production. Due to the quantity decrease of this raw material, cement production went on using the mixture of other members of the flysch series: limestones, marls, clay, loess, sandstones a.o. By the analysis of natural materials the CaCO^ content has mostly been proved. Therefore, knowing the correlation of oxides in mineral raw material is of special significance. The article discusses investigation results of the correlation between CaCO-i and other oxides of the raw material (the paper is published in Croatian.

  10. One step sintering of homogenized bauxite raw material and kinetic study

    Gao, Chang-he; Jiang, Peng; Li, Yong; Sun, Jia-lin; Zhang, Jun-jie; Yang, Huan-ying

    2016-10-01

    A one-step sintering process of bauxite raw material from direct mining was completed, and the kinetics of this process was analyzed thoroughly. The results show that the sintering kinetics of bauxite raw material exhibits the liquid-phase sintering behavior. A small portion of impurities existed in the raw material act as a liquid phase. After X-ray diffraction analyses, scanning electron microscopy observations, and kinetics calculations, sintering temperature and heating duration were determined as the two major factors contributing to the sintering process and densification of bauxite ore. An elevated heating temperature and longer duration favor the densification process. The major obstacle for the densification of bauxite material is attributed to the formation of the enclosed blowhole during liquid-phase sintering.

  11. Reuse and recovery of raw materials: Towards the achievement of a resource-efficient society

    Brunori, Claudia; Cutaia, Laura; Norabito, Roberto

    2015-01-01

    Resource efficiency plays a key role in the transition from a linear to a circular economy system. During the last few decades a rapid growth in the number of materials used across complex products has occurred. Given the high economic importance of critical raw materials combined with relatively high supply risk, securing reliable and undistorted access of certain raw materials is of growing concern across the globe. Development of eco-innovative approaches devoted to closing the loop of resources is strongly needed, allowing the connection between production cycles and their territory.

  12. Proto pectin degradation of raw material by the acid hydrolysis

    Khalikov, D.Kh.; Gorshkova, R.M.; Khalikova, S.; Avloev, Kh.Kh.; Mukhiddinov, Z.K.

    2007-01-01

    The article presents results of hydrolysis proto pectin apples, an orange and a basket of sunflower depending on ph a solution. The reaction products are divided into three fractions conditionally named as micro gel, pectin substances and oligosaccharide. It was shown that the high-quality pectin extracted from orange, but high percentage of carboxylic group in the sunflower pectin allow it to by used as a drug delivery materials

  13. Energy and resource saving raw materials for dactyloscopy

    Ikonnikova Lyubov F.

    2014-01-01

    Full Text Available The “developing” properties of ferromagnetic fingerprint powders are defined by the chemical nature and the particle sizes of the pigment which form acidity of its surface, adhesive and magnetic properties, and color spectrum. The optimum ratio of these physical and chemical parameters is observed in the pigment consisting of iron-containing sludge tempered at 800°C, which contains α-Fe2O3 and impurity of clay materials.

  14. EFFICIENCY OF RAW MATERIAL INVENTORIES IN IMPROVING SUPPLY CHAIN PERFORMANCE of CV. FIVA FOOD

    Artadi Nugraha

    2016-01-01

    Full Text Available The production and number of processed food industries have slightly increased; as a result, the companies must compete to maximize their profits by conducting their efficient production process. CV. Fiva Food is one of the companies in the field of processed foods, especially in processed meat that has implemented supply chain management. It is necessary for the company to take measurements of its performance and efficiency for the entire supply chain such as procurement of raw materials. The purposes of this study were to analyze the performance of the company's supply chain and determine the most efficient  method of procurement for its raw materials as well as and to provide recommendations for the company to improve its performance of entire supply chain. This study used SCOR in analyzing the performance of supply chain and EOQ and POQ method to be compared with the method that the company uses to determine which method of procurement for raw materials is the most efficient one. The result showed that based on the matrix, the company's performance is unfavorable when it was compared to the benchmark performance of inventory days of supply. In addition, this study showed that the POQ method produces the lowest total inventory cost with savings of Rp6.647.015 for raw materials of MDM whereas EOQ method produced the lowest total inventory cost with savings of Rp222.153,78 for raw materials of FQ85CL. Keywords: performance suppy chain, SCOR, fiva food, EOQ, POQ

  15. Efficiency of raw materials. Relief of the economy, environmental protection; Rohstoffeffizienz. Wirtschaft entlasten, Umwelt schonen

    NONE

    2010-11-15

    In the contribution under consideration, the Federal Statistical Office (Wiesbaden, Federal Republic of Germany) and the Federal Environmental Agency (Dessau-Rosslau, Federal Republic of Germany) present actual data and analyses from environmentally economic total computations. In Germany, the use of raw materials became more efficient. Thus, 580 tons of raw materials per million Euro of gross domestic product were needed in the year 2008, while still 680 tons of raw materials were needed in the year 2000. The economical handling of natural resources relieves the environment and enables economic chances for individual companies and national economy. The lowering of environmental effects is to be in the focus of withdrawal and use of raw materials. This requires a stronger reduction of the consumption of raw materials. Savings potentials and an increased efficiency must be aspired in the short and medium term. The politics must create suitable incentives and framework conditions. The contribution under consideration presents new activities and strategies in order to achieve these targets.

  16. Void swelling in fast reactor irradiated high purity binary iron-chromium alloys

    Little, E.A.; Stow, D.A.

    The void swelling characteristics of a series of high purity binary iron-chromium alloys containing 0 - 615 0 C. The void swelling behaviour can be qualitatively rationalized in terms of point defect trapping and precipitation processes involving chromium atoms

  17. Confined recrystallization of high-purity aluminium during accumulative roll bonding of aluminium laminates

    Chekhonin, Paul; Beausir, Benoît; Scharnweber, Juliane; Oertel, Carl-Georg; Hausöl, Tina; Höppel, Heinz Werner; Brokmeier, Heinz-Günter; Skrotzki, Werner

    2012-01-01

    Aluminium laminates consisting of high-purity aluminium and commercially pure aluminium have been produced by accumulative roll bonding (ARB) at ambient temperature for up to 10 cycles. To study the microstructure and texture development of the high-purity aluminium layers with regard to the shrinking layer thickness during ARB, microstructure and texture investigations were carried out by electron backscatter diffraction and neutron and X-ray diffraction, respectively. While the commercially pure aluminium layers develop an ultrafine-grained microstructure, partial discontinuous recrystallization occurs in the high-purity layers. The texture of the high-purity layers mainly consists of Cube and “Tilted Cube” (tilted with respect to the transverse direction) components. The experimental results are discussed with respect to confined recrystallization in the ARB aluminium laminates.

  18. Electrical properties of as-grown and proton-irradiated high purity silicon

    Krupka, Jerzy, E-mail: krupka@imio.pw.edu.pl [Institute of Microelectronics and Optoelectronics, Warsaw University of Technology, Koszykowa 75, 00-662 Warsaw (Poland); Karcz, Waldemar [Joint Institute for Nuclear Research, Joliot-Curie 6, 141980 Dubna (Russian Federation); Kamiński, Paweł [Institute of Electronic Materials Technology, Wólczyńska 13, 301-919 Warsaw (Poland); Jensen, Leif [Topsil Semiconductor Materials A/S, Siliciumvej 1, DK-3600 Frederikssund (Denmark)

    2016-08-01

    The complex permittivity of as-grown and proton-irradiated samples of high purity silicon obtained by the floating zone method was measured as a function of temperature at a few frequencies in microwave spectrum by employing the quasi TE{sub 011} and whispering gallery modes excited in the samples under test. The resistivity of the samples was determined from the measured imaginary part of the permittivity. The resistivity was additionally measured at RF frequencies employing capacitive spectroscopy as well as in a standard direct current experiment. The sample of as-grown material had the resistivity of ∼85 kΩ cm at room temperature. The sample irradiated with 23-MeV protons had the resistivity of ∼500 kΩ cm at 295 K and its behavior was typical of the intrinsic material at room and at elevated temperatures. For the irradiated sample, the extrinsic conductivity region is missing and at temperatures below 250 K hopping conductivity occurs. Thermal cycle hysteresis of the resistivity for the sample of as-grown material is observed. After heating and subsequent cooling of the sample, its resistivity decreases and then slowly (∼50 h) returns to the initial value.

  19. MIS High-Purity Plutonium Oxide Metal Oxidation Product TS707001 (SSR123): Final Report

    Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Narlesky, Joshua Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Max A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carillo, Alex [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-09

    A high-purity plutonium dioxide material from the Material Identification and Surveillance (MIS) Program inventory has been studied with regard to gas generation and corrosion in a storage environment. Sample TS707001 represents process plutonium oxides from several metal oxidation operations as well as impure and scrap plutonium from Hanford that are currently stored in 3013 containers. After calcination to 950°C, the material contained 86.98% plutonium with no major impurities. This study followed over time, the gas pressure of a sample with nominally 0.5 wt% water in a sealed container with an internal volume scaled to 1/500th of the volume of a 3013 container. Gas compositions were measured periodically over a six year period. The maximum observed gas pressure was 138 kPa. The increase over the initial pressure of 80 kPa was primarily due to generation of nitrogen and carbon dioxide gas in the first six months. Hydrogen and oxygen were minor components of the headspace gas. At the completion of the study, the internal components of the sealed container showed signs of corrosion, including pitting.

  20. MIS High-Purity Plutonium Oxide Hydride Product 5501579 (SSR124): Final Report

    Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Narlesky, Joshua Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinex, Max A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carillo, Alex [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2018-02-08

    A high-purity plutonium dioxide material from the Material Identification and Surveillance (MIS) Program inventory has been studied with regard to gas generation and corrosion in a storage environment. Sample 5501579 represents process plutonium oxides from hydride oxide from Rocky Flats that are currently stored in 3013 containers. After calcination to 950°C, the material contained 87.42% plutonium with no major impurities. This study followed over time, the gas pressure of a sample with nominally 0.5 wt% water in a sealed container with an internal volume scaled to 1/500th of the volume of a 3013 container. Gas compositions were measured periodically over a six year period. The maximum observed gas pressure was 124 kPa. The increase over the initial pressure of 70 kPa was primarily due to generation of nitrogen and carbon dioxide gas. Hydrogen and oxygen were minor components of the headspace gas. At the completion of the study, the internal components of the sealed container showed signs of corrosion.

  1. Analysis technique of impurity in high purity deuterium by cryogenic gas-chromatography

    Zhou Junbo; Gao Liping

    2007-01-01

    A veracious and applicable quantitative analysis method of O 2 , N 2 and H 2 , HD in high purity deuterium by the chromatogram columniation filled with 5A molecular sieve and alumina was researched and constituted at natural temperature and 77 K, respectively. Minimum detecting limit of the present method is (150-200) x 10 -6 for H 2 and HD, and it can meet the need of quantitative analysis of the impurity during high purity deuterium preparation. (authors)

  2. High-purity fatty acid methyl ester production from canola, soybean, palm, and yellow grease lipids by means of a membrane reactor

    Cao Peigang; Dube, Marc A.; Tremblay, Andre Y.

    2008-01-01

    High-purity fatty acid methyl ester (FAME) was produced from different lipids, such as soybean oil, canola oil, a hydrogenated palm oil/palm oil blend, yellow grease, and brown grease, combined with methanol using a continuous membrane reactor. The membrane reactor combines reaction and separation in a single unit, provides continuous mixing of raw materials, and maintains a high molar ratio of methanol to lipid in the reaction loop while maintaining two phases during the reaction. It was demonstrated that the membrane reactor can be operated using a very broad range of feedstocks at highly similar operating conditions to produce FAME. The total glycerine and free glycerine contents of the FAME produced were below the ASTM D6751 standard after a single reaction step. Under essentially the same reaction conditions, a conventional batch reaction was not able to achieve the same degree of FAME purity. The effect of the fatty acid composition of the lipid feedstocks on the FAME purity was also shown. It was demonstrated that, due to the fatty acid composition, FAME from virgin soybean oil and virgin canola oil was produced in the membrane reactor within ASTM specifications even without a water washing step

  3. Ferroelectric thin films using oxides as raw materials

    E.B. Araújo

    1999-01-01

    Full Text Available This work describes an alternative method for the preparation of ferroelectric thin films based on pre-calcination of oxides, to be used as precursor material for a solution preparation. In order to show the viability of the proposed method, PbZr0.53Ti0.47O3 and Bi4Ti3O12 thin films were prepared on fused quartz and Si substrates. The results were analyzed by X-ray Diffraction (XRD, Scanning Electron Microscopy (SEM, Infrared Spectroscopy (IR and Rutherford Backscattering Spectroscopy (RBS. The films obtained show good quality, homogeneity and the desired stoichiometry. The estimated thickness for one layer deposition was approximately 1000 Å and 1500 Å for Bi4Ti3O12 and PbZr0.53Ti0.47O3 films, respectively.

  4. Natural radioactivity and human exposure by raw materials and end product from cement industry used as building materials

    Stojanovska, Z.; Nedelkovski, D.; Ristova, M.

    2010-01-01

    During the manufacturing process in the cement industry, raw materials of different levels of natural radioactivity are utilized. In this study we present the radiological impact of cements as a building material and the different raw materials used in their manufacture. A total of 218 samples of raw materials and their end product cements were collected from the cement industry of Macedonia (The Former Yugoslav Republic) during the period 2005-2007. The specific activities, evaluated by gamma spectrometry analysis, showed the highest mean specific activity in fly ash ( 226 Ra, 107 ± 45 Bq kg -1 ; 232 Th, 109 ± 30 Bq kg -1 ; 40 K, 685 ± 171 Bq kg -1 ), which is used as a raw material. However, the final cement product usually has relatively lower activity compared with the activity of the raw material and the mean specific activity of the final cement products were lower ( 226 Ra, 42 ± 10 Bq kg -1 ; 232 Th, 28 ± 6 Bq kg -1 ; 40 K, 264 ± 50 Bq kg -1 ). The radium equivalent activity and the hazard index were calculated for each sample to assess the radiation hazard. The mean annual effective dose originating from the cements was found to be 111 ± 22 μSv y -1 , which is below the recommended EC limit of 300 μSv y -1 .

  5. High purity tellurium production using dry refining processes

    Unknown

    Centre for Materials for Electronics Technology (C-MET), IDA Phase II, Cherlapally, HCL Post, Hyderabad 500 051,. India ... The total content of gas and gas forming impurities like O, N and C are found to be .... (DIT), Government of India.

  6. Irradiation as an alternative environment friendly method for microbiological decontamination of herbal raw material

    Gorecki, P.; Kedzia, B.; Migdal, W.; Owczarczyk, H.B.

    1998-01-01

    Microbiological contamination of herbal raw materials is a serious problem in the production of therapeutical preparations. A good quality of the product, according to the pharmaceutical requirements may be achieved by applying suitable methods of decontamination. The decontamination treatments should be fast and effective against all microorganisms. It should ensure the decontamination of both packaging and the product in order to act effectively against all the microorganisms present and must not reduce the sensory and technological qualities of the commodities. In the paper, the results of comparative investigations on the microbiological decontamination of herbal raw materials by chemical (ethylene oxide, methyl bromide) and physical method (irradiation) are presented. Decontamination of herbal raw materials by irradiation is a method by choice. It is because chemical methods have been recognized recently as not safe to the consumer. Irradiation, in turn, is technically feasible, very effective and friendly enough to environment process

  7. To the question of peculiarities of thermal activation of natural siliceous raw material

    Chumachenko Natalya

    2017-01-01

    Full Text Available The results of research of activity enhancement of natural siliceous raw material are given in the article. Fossil meal of Khotynetsky deposit, diatomite of Sharlovsky deposit, silica clay of Balasheika deposit were used as natural active mineral admixtures. The influence of heat-treating temperature and dispersion on activity of different types of siliceous raw material is studied. The increase of activity of fixation of Ca(OH2 in several times is traced after heat-treating at a certain temperature in the range from 100 to 800°C. The type of activity change is discovered. Explanation is given connected with the change of silica structure in the surface layer. Parameters of the highest activity are defined for every type of siliceous raw material.

  8. Development of a facility for the recovery of high-purity hydrogen from coke oven gas by pressure swing adsorption

    Nakamura, M; Saida, K; Uenoyama, K; Sugishita, M; Imokawa, K

    1985-01-01

    This paper reports 1) a pressure swing adsorption (PSA) system comprising three towers, each packed with three different adsorbents; and 2) studies of the application of this system to the recovery of high-purity hydrogen from coke oven gas. Running the adsorption plant at 35 C and 9.5 kg/cm/sup 2/ gives optimum operating stability and economy. In addition, an optimum time cycle for the three-tower system has been developed. Gas from the PSA equipment proper still contains traces of oxygen. This is removed in a further tower packed with Pd catalyst. The ultimate recovery of hydrogen is closely related to its concentration in the raw coke oven gas and to the degree of purity attained. 3 references.

  9. Raw material generated from pet bottle recycling and its derivatives

    João Almeida Santos

    2015-08-01

    Full Text Available The recycling process is no longer a pejorative connotation business to become the main business of any company not only because of the need to conserve virgin resources, but mainly because of the benefits to the environment. In this sense, this paper aims at assessing the possibility of exports of polyethylene terephthalate - PET known for - a type of product that can be recycled and reprocessed into products of various types and applications. This article has been structured based on exploratory research bibliographic database of scientific articles, books, newspapers and magazines where we analyze the main steps involved in the recycling of PET and its exploitation for export. Support of organizations and associations such as the Brazilian Association of PET (ABIPET contributed to the development of theoretical framework. The market operated and what can still be very large, with the possibility of exponential growth supported by: the economy in the use of virgin resources reduces the impact of chemicals in the environment, saving energy used in the production process, reducing the use of financial resources allocated to the reuse of materials.

  10. High purity ferritic Cr-Mo stainless steel

    Knoth, J.

    1977-01-01

    In five years, E-BRITE 26-1 ferritic stainless steel has won an important place in the spectrum of materials suitable for use in chemical process equipment. It provides, in stainless steel, performance-capability characteristics comparable to more expensive alloys. It has demonstrated cost-effectiveness in equipment used for caustic, nitric-urea, organic chemicals, pulping liquors, refinery streams, and elsewhere. User confidence in the reliability and integrity of Grade XM 27 has increased to the point where large critical systems are now routinely specified in the alloy. The market acceptance of this material has attracted attempts to produce substitute versions of the alloy. Imitation, should be viewed with caution. Stabilized 26-IS must be examined over a lengthy period of time to determine if its own corrosion resistance, ductility, fabricability and reproducibility properties could ever be likened to those of E-BRITE 26-1. (orig.) [de

  11. Dynamical recrystallization of high purity austenitic stainless steels

    Gavard, L.

    2001-01-01

    The aim of this work is to optimize the performance of structural materials. The elementary mechanisms (strain hardening and dynamical regeneration, germination and growth of new grains) occurring during the hot working of metals and low pile defect energy alloys have been studied for austenitic stainless steels. In particular, the influence of the main experimental parameters (temperature, deformation velocity, initial grain size, impurities amount, deformation way) on the process of discontinuous dynamical recrystallization has been studied. Alloys with composition equal to those of the industrial stainless steel-304L have been fabricated from ultra-pure iron, chromium and nickel. Tests carried out in hot compression and torsion in order to cover a wide range of deformations, deformation velocities and temperatures for two very different deformation ways have allowed to determine the rheological characteristics (sensitivity to the deformation velocity, apparent activation energy) of materials as well as to characterize their microstructural deformations by optical metallography and electron back-scattered diffraction. The influence of the initial grain size and the influence of the purity of the material on the dynamical recrystallization kinetics have been determined. An analytical model for the determination of the apparent mobility of grain boundaries, a semi-analytical model for the dynamical recrystallization and at last an analytical model for the stationary state of dynamical recrystallization are proposed as well as a new criteria for the transition between the refinement state and the state of grain growth. (O.M.)

  12. Prospect of trema orientalis as a pulping raw material in bangladesh

    Jahan, M.S.

    2013-01-01

    The pulp and paper industry in Bangladesh is looking for new raw materials with high productivity per hectare. Currently, bamboo and Gmelina arborea are the main pulping raw materials for the pulp and paper industry of the country. Trema orientalis is one of the fastest growing woods in the tropical region. This paper reviews the literature on the topic, in particular, related to the chemical, morphological and physical properties of T. orientalis and its suitability for pulping. In addition, the advantages and disadvantages of various ulping processes proposed in the literature were critically analyzed. It was concluded that T. orientalis is a potential pulp wood for the Bangladesh pulp and paper industry. (author)

  13. DELINEATION OF BOUNDARY CONTOURS OF MINERAL RAW MATERIALS WITHIN THE DEPOSIT SPACE CONSIDERING THE QUALITY

    Ivan Tomašić

    1990-12-01

    Full Text Available On the basis of performed explorations, in the phase of deposit preparation and development for exploitation the obtained results regarding the raw material quality were transfered to the surface. The results served both for the development and planning of deposit excavation dynamics and for the delineation of boundary contours by mineral raw materials within the deposit space considering the quality, The case presented in the article refers to the marl and limestone open pit for the cement industry, the »Partizan« near Split (the paper is published in Croatian.

  14. Mining of Radioactive Raw Materials as an Origin of the Nuclear Fuel Chain

    Bedřich Michálek

    2007-01-01

    Full Text Available The mining of radioactive raw materials may be considered as an origin of the nuclear fuel chain and thus determines the amount of radioactive wastes which have to be stored safety in the final stage of the fuel chain. The paper informs about the existing trends in mining of radioactive raw materials in the world, provides an overview of development in mining in the Czech Republic and of possibilities of future exploiting some uranium deposits. It points a possibility of non-traditional obtaining uranium from mine waters from underground uranium mines closed and flooded earlier.

  15. Colorimetric determination of a paracetamole in raw material and in pharmaceutical dosage forms

    Usifoh, C.O; Adelusi, S.A.; Adebambo, R.F.

    2002-01-01

    A rapid, accurate and simple method is proposed for the determination of p-acetaminophen (paracetamole) in raw material, tablets and syrups. The method is based on measuring the intensity of the yellow color that developed when acute acetaminophen is allowed to react with p-dimethylaminobenzaldehyde in 2M HCl after heating. The color which absorbs in the visible region of gamma 450 nm is stable for several hours and the intensity is directly proportional to the concentration of the drug, that is, Beer lambert law is obeyed. The method can be used to analyse paracetamole in raw material and in pharmaceutical dosage forms. (author)

  16. Sensory properties of marinated herring (Clupea harengus) processed from raw material from commercial landings

    Nielsen, Durita; Hyldig, Grethe; Nielsen, Jette

    2005-01-01

    Sensory properties of marinated herring processed from raw material from Danish commercial catches were described and related to fishing season and biological, chemical and functional properties. Herring was caught on five cruises and stored on board in tanks or ice. The sensory profile of marina......Sensory properties of marinated herring processed from raw material from Danish commercial catches were described and related to fishing season and biological, chemical and functional properties. Herring was caught on five cruises and stored on board in tanks or ice. The sensory profile...

  17. Raw material consumption of the European Union--concept, calculation method, and results.

    Schoer, Karl; Weinzettel, Jan; Kovanda, Jan; Giegrich, Jürgen; Lauwigi, Christoph

    2012-08-21

    This article presents the concept, calculation method, and first results of the "Raw Material Consumption" (RMC) economy-wide material flow indicator for the European Union (EU). The RMC measures the final domestic consumption of products in terms of raw material equivalents (RME), i.e. raw materials used in the complete production chain of consumed products. We employed the hybrid input-output life cycle assessment method to calculate RMC. We first developed a highly disaggregated environmentally extended mixed unit input output table and then applied life cycle inventory data for imported products without appropriate representation of production within the domestic economy. Lastly, we treated capital formation as intermediate consumption. Our results show that services, often considered as a solution for dematerialization, account for a significant part of EU raw material consumption, which emphasizes the need to focus on the full production chains and dematerialization of services. Comparison of the EU's RMC with its domestic extraction shows that the EU is nearly self-sufficient in biomass and nonmetallic minerals but extremely dependent on direct and indirect imports of fossil energy carriers and metal ores. This implies an export of environmental burden related to extraction and primary processing of these materials to the rest of the world. Our results demonstrate that internalizing capital formation has significant influence on the calculated RMC.

  18. Raw material procurement for termite fishing tools by wild chimpanzees in the Issa valley, Western Tanzania.

    Almeida-Warren, Katarina; Sommer, Volker; Piel, Alex K; Pascual-Garrido, Alejandra

    2017-10-01

    Chimpanzee termite fishing has been studied for decades, yet the selective processes preceding the manufacture of fishing tools remain largely unexplored. We investigate raw material selection and potential evidence of forward planning in the chimpanzees of Issa valley, western Tanzania. Using traditional archaeological methods, we surveyed the location of plants from where chimpanzees sourced raw material to manufacture termite fishing tools, relative to targeted mounds. We measured raw material abundance to test for availability and selection. Statistics included Chi-Squared, two-tailed Wilcoxon, and Kruskall-Wallace tests. Issa chimpanzees manufactured extraction tools only from bark, despite availability of other suitable materials (e.g., twigs), and selected particular plant species as raw material sources, which they often also exploit for food. Most plants were sourced 1-16 m away from the mound, with a maximum of 33 m. The line of sight from the targeted mound was obscured for a quarter of these plants. The exclusive use of bark tools despite availability of other suitable materials indicates a possible cultural preference. The fact that Issa chimpanzees select specific plant species and travel some distance to source them suggests some degree of selectivity and, potentially, forward planning. Our results have implications for the reconstruction of early hominin behaviors, particularly with regard to the use of perishable tools, which remain archaeologically invisible. © 2017 Wiley Periodicals, Inc.

  19. Processing biofuels from farm raw materials - A systems study; Pelletering och brikettering av jordbruksraavaror - En systemstudie

    Nilsson, Daniel; Bernesson, Sven

    2008-03-15

    Use of processed biofuels (pellets, briquettes) has greatly increased in Sweden in recent decades, mainly to replace fossil fuels in large boilers, e.g. in coal powder boilers. More recently, the demand from private households and residential heating systems has also increased, mainly due to conversion from fossil heating oil. This increased interest in pellets and briquettes for heating is beginning to cause a shortage of the traditional raw materials, sawdust and wood shavings, and therefore attention is turning to using a variety of agricultural products as raw material. Such raw materials include cultivated energy crops and wastes and by-products from agriculture. This study describes the typical systems currently used for production of pellets and briquettes and investigates the possibility of using energy crops (Salix, reed canary-grass and hemp) and various wastes and by-products from processing of farm products (straw, cereal screenings, rape-seed meal and distiller's waste) as raw materials. Previous experiences of pelletizing and briquetting of these raw materials are reviewed in order to comprehensively identify possible combustion problems that may occur. On the basis of the results obtained, scenarios for possible production systems in a five-year perspective are presented and the costs and energy demands for these systems calculated. These future scenarios include large scale plants and micro-scale plants, as well as static and mobile equipment. The five main conclusions from the study are: - The farm raw materials of greatest interest for large-scale production are pelleted Salix and reed canary-grass. They have competitive prices and acceptable fuel properties and could be mixed with sawdust in existing large-scale pelletizing factories in Sweden. - Straw has low production costs but can cause serious ash-related problems. Hemp has too high production costs to be of commercial interest, while distiller's waste and rape-seed meal currently

  20. TATA LETAK GUDANG RAW MATERIAL CHEMICAL MENGGUNAKAN METODE SHARED STORAGE DAN REL SPACE

    Indramawan Hadi Kuswoyo

    2016-04-01

    Full Text Available Storage system in the manufacturing industry in this modern era is a very important role especially international scale company, may not directly produce or distribute all of the work unit. this led to the need for raw materials warehouse, warehouse storage systems should not be large in size because if supported by a good inventory of the warehouse to the maximum utilization of the problems faced by the company occurred in the warehouse of raw materials (raw materials. deficiencies in the arrangement of items in the warehouse procedures cause problems in the warehouse, so the warehouse impressed narrow and less structured cause inefficiencies time retrieval and storage of materials, as well as complicate the operator in handling the placement process raw materials. In the method of shared storage and rail space (relationchip chart for the relationship between activity is indicated by activity relationship approach, which shows each activity as a single activity model in the form of a diagram. ARD basic idea of the link between patterns of flow of goods and location of service activities related to production activities. ARD is the development of ARC (activity relationship chart.

  1. Replacement of reserves zinc based on the recycling of technogenic raw materials

    Olga Sergeevna Bryantseva

    2013-06-01

    Full Text Available In the article, the perspective trends of the expansion of the mineral-ore base of the Russian producers of zinc by recycling of technogenic raw materials are considered. The important role of recycling of resources for sustainable development of society and improve the environmental safety is justified. The main structural and dynamic characteristics of the use of mineral resource base for the production of zinc in Russia are considered. Raw materials opportunities and constraints for the development of zinc production are analyzed. In the paper, the structure and dynamics of the use of recycled materials by the largest producer of zinc in Russia are investigated. The methodical approach to the estimation of effectiveness of the industrial processing of technogenic metallurgical raw materials with the strategic flexibility of the implementation of projects is proposed and approved. The estimation of the effectiveness of a complex industrial processing of metallurgical zinc-containing dusts in a real production is carried out. The value of the strategic flexibility of the project of the industrial processing of the zinc-containing technogenic raw material is determined on the basis of the developed systematic approach. The value of the processes of recycling for sustainable production of zinc in Russia is revealed.

  2. Surface characterization for high purity Fe-Cr alloys

    Iwai, H.; Oiwa, R.; Takaki, S.; Abiko, K.

    1995-01-01

    Fe-50mass%Cr was prepared in a cold crucible furnace with induction heating, then refined by floating-zone melting (FZM). The chemistries on the surface before and after FZM were compared by XPS measurement. C and O were observed on top surfaces both before and after as a hydrocarbon, carbonyl group and carboxyl group which are adsorbed chemical components. The other impurities were observed on the surface in both cases; however, the number and level of impurities on the surface after FZM were much larger than those on the surface before FZM; these adhered to the surface during sample preparation for XPS measurement. It is concluded that sample preparation introduces contamination which affects the detection limit of chemical analytical instruments. Sn was only observed on the top surface after FZM. It was segregated Sn which was contained in chromium as a starting material. It must be eliminated before starting. From XPS depth profiling results, it was concluded that 0.2 nm thickness of carbon such as hydrocarbon and organic components are adsorbed on the 1 nm thickness of oxide layer. Below the oxide layer, a lack of Cr was observed down to a depth of 6 nm. (orig.)

  3. Characterization of raw materials to obtain the mass for white ware, using waste glass

    Cavalcanti, M.S.L.; Porto, V.S.; Meneses, R.L; Albuquerque, A.V.; Guedes, B.F.R.; Morais, C.R.S.; Santana, L.N.L.

    2009-01-01

    A major problem faced in the post modern society is the huge amount of glass, accumulated in landfills cities. The glass material is one hundred percent recyclable and has the property to act as fluxes as well as feldspar. Given this premise, this study aimed to characterize materials - raw materials and waste glass regional plan for development of ceramic bodies with the similar behavior produced industrially, using shards of glass to partially replace the feldspar. The materials - raw materials used were clay, ball clay, kaolin, quartz, feldspar and shard of glass, being characterized by the techniques: chemical analysis, size analysis, differential thermal analysis vibrational spectroscopy in the infrared region, the Ray-Diffraction X and scanning electron microscopy. The results showed that the waste had higher rates of vitreous oxides fluxes and similar. (author)

  4. Modelling of hydrogen permeability of membranes for high-purity hydrogen production

    Zaika, Yury V.; Rodchenkova, Natalia I.

    2017-11-01

    High-purity hydrogen is required for clean energy and a variety of chemical technology processes. Different alloys, which may be well-suited for use in gas-separation plants, were investigated by measuring specific hydrogen permeability. One had to estimate the parameters of diffusion and sorption to numerically model the different scenarios and experimental conditions of the material usage (including extreme ones), and identify the limiting factors. This paper presents a nonlinear mathematical model taking into account the dynamics of sorption-desorption processes and reversible capture of diffusing hydrogen by inhomogeneity of the material’s structure, and also modification of the model when the transport rate is high. The results of numerical modelling allow to obtain information about output data sensitivity with respect to variations of the material’s hydrogen permeability parameters. Furthermore, it is possible to analyze the dynamics of concentrations and fluxes that cannot be measured directly. Experimental data for Ta77Nb23 and V85Ni15 alloys were used to test the model. This work is supported by the Russian Foundation for Basic Research (Project No. 15-01-00744).

  5. Influence of Ta Content in High Purity Niobium on Cavity Performance Preliminary Results*

    Kneisel, P

    2004-01-01

    In a previous paper* a program designed to study the influence of the residual tantalum content on the superconducting properties of pure niobium metal for RF cavities was outlined. The main rationale for this program was based on a potential cost reduction for high purity niobium, if a less strict limit on the chemical specification for Ta content, which is not significantly affecting the RRR–value, could be tolerated for high performance cavities. Four ingots with different Ta contents have been melted and transformed into sheets. In each manufacturing step the quality of the material has been monitored by employing chemical analysis, neutron activation analysis, thermal conductivity measurements and evaluation of the mechanical properties. The niobium sheets have been scanned for defects by an eddy current device. From three of the four ingots—Ta contents 100, 600 and 1,200 wppm—two single cell cavities each of the CEBAF variety have been fabricated and a series of tests on each ...

  6. Simultaneously Recovering High-Purity Chromium and Removing Organic Pollutants from Tannery Effluent

    Jie Zong

    2016-01-01

    Full Text Available Chromium pollution is a serious issue because of carcinogenic toxicities of the pollutants and low recovery rate of chromium because of the presence of organic, such as protein and fat. In this work, high recovery rate and high purity of the chromium ion were successfully prepared by the way of acid enzyme, flocculant, and Fenton oxidation. The experiments were characterized by TG, TOC, UV-VIS, and SEM. In the work, the tannery waste chrome liquor was used as experimental material. The results showed that the percentage of reduction of TOC in the tannery waste chrome liquor by method of Fenton oxidation, acid enzyme, and the flocculant was 71.15%, 65.26%, and 22.05%, respectively. Therefore, the organism content of chrome tanning waste liquid was greatly reduced through the pretreatment. And the application experiment showed that the properties and grain surface and fibers of the tanned leather with commercial chromium powder and chrome tanning agent prepared from the chromium waste liquid treated with Fenton are nearly the same.

  7. Oat raw materials and bakery products - amino acid composition and celiac immunoreactivity.

    Mickowska, Barbara; Litwinek, Dorota; Gambuś, Halina

    2016-01-01

    The aim of this study was to compare the biochemical and immunochemical properties of avenins in some special oat raw materials and additionally the possibility of using them as a raw material for the gluten-free bakery products. The compared oat raw materials were - oat flakes, commercial oat flours (including gluten-free oat flour) and residual oat flour, which is by-product of β-glucan preparation. Biochemical characteristic included amino acid compositions and SDS-PAGE profiles of extracted avenins. The immunochemical reactivity with polyclonal anti-gluten and monoclonal anti-gliadin antibodies was evaluated qualitatively and quantitatively by immunoblotting and ELISA methods. Additionally, experimental bakery products made of examined raw materials were assessed according to their suitability for the celiac patients' diet. The highest protein content was measured in the β-glucan preparation "Betaven" and gluten-free oat flour. Proteins of all materials are rich in glutamic and aspartic acid, leucine and arginine. Proportions of amino acids in avenins extracted from most of oat raw materials are similar, excluding gluten-free oat flour, which has a very low avenin content and proportions of individual amino acids are different. The SDS-PAGE protein pattern consisted of proteins with molecular weight of about 25-35 kDa. Polyclonal anti-gluten anti-body recognized all protein fractions of molecular weight higher than 20 kDa. Quantitative ELISA analysis shows that the majority of samples has a gliadin-like protein content within the range of 80-260 mg/kg, excluding gluten-free flours and corresponding bakery products. Altogether, β-glucan preparation has extremely high level of gliadin-like proteins. In the examined oat raw materials and foods the contents of immunoreactive amino acid sequences exceeded the limit of 20 mg/kg (considered as gluten-free) except for gluten-free flours (oat and  the prepared mixture) and the bakery products based on gluten

  8. An integrated production-inventory model for food products adopting a general raw material procurement policy

    Fauza, G.; Prasetyo, H.; Amanto, B. S.

    2018-05-01

    Studies on an integrated production-inventory model for deteriorating items have been done extensively. Most of the studies define deterioration as physical depletion of some inventories over time. This definition may not represent the deterioration characteristics of food products. The quality of food production decreases over time while the quantity remains the same. Further, in the existing models, the raw material is replenished several times (or at least once) within one production cycle. In food industries, however, a food company, for several reasons (e.g., the seasonal raw materials, discounted price, etc.) sometimes will get more benefit if it orders raw materials in a large quantity. Considering this fact, this research, therefore, is aimed at developing a more representative inventory model by (i) considering the quality losses in food and (ii) adopting a general raw material procurement policy. A mathematical model is established to represent the proposed policy in which the total profit of the system is the objective function. To evaluate the performance of the model, a numerical test was conducted. The numerical test indicates that the developed model has better performance, i.e., the total profit is 2.3% higher compared to the existing model.

  9. On the increasing multifunctionality of agricultural raw materials: three dilemmas for innovation and adoption

    Boehlje, M.; Bröring, S.

    2010-01-01

    The agricultural sector is increasingly becoming multifunctional. It is the entry point of several value chains. Agricultural raw materials are increasingly being used for multiple industries or sectors beyond the traditional fiber and nutrition industries—energy in the form of ethanol and

  10. The increasing multifunctionality of Agricultural Raw Materials: Three dilemmas for Innovation and Adoption

    Boehlje, M.; Bröring, S.

    2011-01-01

    Agricultural raw materials are increasingly being used for multiple industries or sectors beyond the traditional fiber and nutrition industries: energy in the form of ethanol and biodiesel, industrial products such as polymers and bio-based synthetic chemicals and fibers, and pharmaceutical/health

  11. Acoustic assessment of wood quality of raw forest materials : a path to increased profitability

    Xiping Wang; Peter Carter; Robert J. Ross; Brian K. Brashaw

    2007-01-01

    Assessment of the quality of raw wood materials has become a crucial issue in the operational value chain as forestry and the wood processing industry are increasingly under economic pressure to maximize extracted value. A significant effort has been devoted toward developing robust nondestructive evaluation (NDE) technologies capable of predicting the intrinsic wood...

  12. Dependence of quality properties for grey iron on used raw materials

    E. Weiss

    2009-01-01

    Full Text Available Grey iron castings keep the first place among castings on base of iron. Present trend in growing entrance production costs of cast stock force manufacturer to cost minimizing. Therefore is most actual deal replacement pig iron by steel scrap. In contribution are presented results research work relating to influence of raw materials on grey iron properties.

  13. Raw material changes and their processing parameters in an extrusion cooking process

    Cheng, Hongyuan; Friis, Alan

    In this work, the effects of raw material and process parameters on product expansion in a fish feed extrusion process were investigated. Four different recipes were studied with a pilot-scale twin-screw co-rotating extruder according to a set of pre-defined processing conditions. In the four rec...

  14. Uncertainty analysis in raw material and utility cost of biorefinery synthesis and design

    Cheali, Peam; Quaglia, Alberto; Gernaey, Krist

    2014-01-01

    are characterized by considerable uncertainty. These uncertainties might have significant impact on the results of the design problem, and therefore need to be carefully evaluated and managed, in order to generate candidates for robust design. In this contribution, we study the effect of data uncertainty (raw...... material price and utility cost) on the design of a biorefinery process network....

  15. Elaborations in the area of complex reprocessing of mineral raw materials

    Mirsaidov, U.M.

    2002-01-01

    In present time complex using of raw materials has important significance as it connected with solving problems of creating of waste less and ecologically clean technologies. Elaboration and assimilation of waste less technologies has special significance for chemical, mountain-chemical, metallurgical branches of industry. In this part of book author gives several methods of waste less and ecologically clean technologies

  16. Cocoa pulp juice (sweatings) as a potential raw material for the ...

    Cocoa sweatings is a very interesting by-product of cocoa production and it forms the substrate for microbial growth during the fermentation process. Most of the sweatings go to waste during the processing of the cocoa beans and this has led to its utilization as a potential raw material for the development of soft drink to ...

  17. 21 CFR 1304.31 - Reports from manufacturers importing narcotic raw material.

    2010-04-01

    ... therefrom. (g) All in-process inventories should be expressed in terms of end-products and not precursors... following information shall be submitted for each type of narcotic raw material (quantities are expressed as... opium, crude alkaloids and other derivatives (quantities are expressed as grams of anhydrous base or...

  18. Melt-drop technique for the production of high-purity metal powder

    Aldinger, F.; Linck, E.; Claussen, N.

    1977-01-01

    The production of high-purity powders of metals and alloys such as beryllium, titanium alloys, or superalloys is a problem. Oxidation of these materials cannot be avoided. Oxidation occurs in inert gases and even in reducing atmospheres when any gas impurities are present. Therefore, the powder production of these materials has to be performed either in high vacuum or at least in a static atmosphere of inert gas purified immediately before coming into contact with the disintegrating material. These requirements are very well met by the melt-drop technique presented in this paper, especially for coarse powders which must not necessarily be cold-workable. This is true, for example, for superalloys where high-temperature applications require large grain sizes; or in titanium alloys because the final microstructure will be achieved by a thermomechanical treatment. In the case of beryllium and beryllium alloys, where grain sizes <5 μm are desired, further milling is necessary. But the melt-drop technique offers a simple and clean method directly from the purifying process of vacuum melting. In melt-drop processes a liquid metal flows through a nozzle at the bottom of a crucible or the melt is just poured through a sieve. The theory of disintegration of a liquid jet into droplets, dates back to the 19th century. More recent investigations attempted to produce uniformly sized droplets by applying a capillary wave of given wave length to the jet. But this has been done only with non-metallic materials. Evidence is presented to prove the theory and show that this concept is applicable to the production of metal powders with controlled particle size

  19. Current problems of raw fish material processing while manufacturing dried products

    Yashonkov A. A.

    2017-09-01

    Full Text Available The substantiation for using techniques of fish raw material canning has been presented, raw fish being caught or farmed in aquaculture. The main problems in raw fish canning have been reviewed, including significant reduction in thermolabile vitamins in the ultimate product as compared with the raw material due to the thermal processing. Promising canning technique – vacuum drying – has been proposed. This technique makes possible to reduce the temperature of thermal processing down to 50…55 °С and significantly enlarge preservation of thermolabile vitamins from the raw fish. Sampling of raw materials, semi-finished products, finished products, including preparation for analysis has been conducted by standard methods. Disadvantages of this way have been found, it is low energy efficiency of the process. The way to intensify the vacuum drying of aquatic organisms has been proposed based on the method of preliminary pore-forming due to augmenting the area of moisture evaporation. The design of the pilot plant has been proposed in order to research the process of pore forming and vacuum drying. Target species for processing have been suggested. They are as follows: Azov goby (fillet for food products and Black Sea sprat for feeds. The recipes of the feed mixture for granulated floating food for trout have been developed. The results of the first series of the pilot research have been provided. The experiments have proved that preliminary pore forming immediately before vacuum drying makes possible to enlarge the surface area of moisture evaporation by 15…25 %. By processing photomicrographs of sections by means of a special software the authors have got the results demonstrating that when manufacturing dried products by pore forming and drying under pressure 10 kPa the pore take 35...38 % of the inner volume of the product and with drying under pressure 10 kPa – only 18...21 %, and when drying under the atmospheric pressure – 11...13 %.

  20. Improving the Technology of Obtaining Technical Ethanol from Alternative Raw Materials

    Sergіj Petrov

    2018-05-01

    Full Text Available The purpose of the article is to study the properties of fallen leaves as raw materials for the production of bioethanol; Improvement of the technology of recycling cellulosic raw materials into bioethanol in the most energy-efficient and ecological way. As a result of the study, it has been found out that the production of biofuels from renewable raw materials is characterized by features of innovative technology: the rapid growth of this sector of economy is accompanied by a significant increase in market share. The use of fallen leaves as raw material will eliminate the current conflict of interests associated with the use of food raw materials for the production of bioethanol, will prevent the withdrawal of resources from the sphere of food production. Significant positive factors in the production and use of biofuels are improvement of environmental conditions, reduction of the harmful effects of exhaust gases on the human body, reducing environmental pollution and, consequently, reducing morbidity and associated costs of medical care. The use of bioethanol as an ecobiopilot makes it possible to increase the octane number of fuel, and, accordingly, increase the efficiency of the engine. Thus, the use of bioethanol leads to a qualitative improvement of technical and economic indicators, which is also an indicator of innovation. The threat of reducing (exhausting non-renewable sources of energy is also the factor that necessitates the development and improvement of biofuel production technology. The relatively low profitability of biofuel production is due to the low yield of the target product and the high cost of pre-treatment of cellulose raw materials. The method of obtaining bioethanol from renewable non-demanded raw materials - fallen leaves - was improved. The technique allows to increase the bioethanol yield due to more effective hydrolysis of hard-hydrolysable polysaccharides. Further development of the study of the differences in

  1. High-Temperature Release of SO2 from Calcined Cement Raw Materials

    Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter

    2011-01-01

    During combustion of alternative fuels in the material inlet end of cement rotary kilns, local reducing conditions may occur and cause reductive decomposition of sulfates from calcined cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2...... concentration, which may cause deposit formation in the kiln system. In this study, the release of sulfur from calcined cement raw materials under both oxidizing and reducing conditions is investigated. The investigations include thermodynamic equilibrium calculations in the temperature interval of 800–1500 °C...... and experiments in a tube furnace reactor in the temperature interval of 900–1100 °C. The investigated conditions resemble actual conditions in the material inlet end of cement rotary kilns. It was found that the sulfates CaSO4, K2SO4, and Na2SO4 were all stable under oxidizing conditions but began to decompose...

  2. The properties of weft knitted fabric medical and preventive treatment action using eco-raw materials

    Halavska, L.; Batrak, O.

    2016-07-01

    A new trend in the world is the clothing production using the new types of ecological raw materials application - milk, pineapple, coconut, hemp, banana, eucalyptus, clams, corn, bamboo, soya, nettle yarn. This makes it possible to create textile materials of new generation with unique antibacterial and antiseptic properties. Such materials have a positive preventive and sometimes therapeutic effect on people, and their health. Eco-raw materials clothing is able to protect the human body from the environment harmful effects: cold, heat, rain, dust, opportunely remove from underclothing layer the steam and gases, sweat; maintain in underclothing layer the necessary microclimate for normal organism functioning. Study of knitwear consumer properties, produced with eco-materials, is an urgent task of the world vector, directed on ecological environmental protection. This paper presents the research results of hygroscopicity and capillarity weft knitted fabrics, what knitted from different types of eco-raw materials: bamboo yarn, yarn containing soybean and nettle yarn. Character of influence of the liquid raising level changes depending on the experiment time and the knitting structure is revealed.

  3. Sustainability evaluation of essential critical raw materials: cobalt, niobium, tungsten and rare earth elements

    Tkaczyk, A. H.; Bartl, A.; Amato, A.; Lapkovskis, V.; Petranikova, M.

    2018-05-01

    The criticality of raw materials has become an important issue in recent years. As the supply of certain raw materials is essential for technologically-advanced economies, the European Commission and other international counterparts have started several initiatives to secure reliable and unhindered access to raw materials. Such efforts include the EU Raw Materials Initiative, European Innovation Partnership on Raw Materials, US Critical Materials Institute, and others. In this paper, the authors present a multi-faceted and multi-national review of the essentials for the critical raw materials (CRMs) Co, Nb, W, and rare earth elements (REEs). The selected CRMs are of specific interest as they are considered relevant for emerging technologies and will thus continue to be of increasing major economic importance. This paper presents a ‘sustainability evaluation’ for each element, including essential data about markets, applications and recycling, and possibilities for substitution have been summarized and analysed. All the presented elements are vital for the advanced materials and processes upon which modern societies rely. These elements exhibit superior importance in ‘green’ applications and products subject to severe conditions. The annual production quantities are quite low compared to common industrial metals. Of the considered CRMs, only Co and REE gross production exceed 100 000 t. At the same time, the prices are quite high, with W and Nb being in the range of 60 USD kg‑1 and some rare earth compounds costing almost 4000 USD kg‑1. Despite valiant effort, in practice some of the considered elements are de facto irreplaceable for many specialized applications, at today’s technological level. Often, substitution causes a significant loss of quality and performance. Furthermore, possible candidates for substitution may be critical themselves or available in considerably low quantities. It can be concluded that one preferred approach for the

  4. Raw materials exploitation in Prehistory of Georgia: sourcing, processing and distribution

    Tushabramishvili, Nikoloz; Oqrostsvaridze, Avthandil

    2016-04-01

    Study of raw materials has a big importance to understand the ecology, cognition, behavior, technology, culture of the Paleolithic human populations. Unfortunately, explorations of the sourcing, processing and distribution of stone raw materials had a less attention until the present days. The reasons of that were: incomplete knowledge of the archaeologists who are doing the late period archaeology (Bronze Age-Medieval) and who are little bit far from the Paleolithic technology and typology; Ignorance of the stone artifacts made on different kind of raw-materials, except flint and obsidians. Studies on the origin of the stone raw materials are becoming increasingly important since in our days. Interesting picture and situation have been detected on the different sites and in different regions of Georgia. In earlier stages of Middle Paleolithic of Djruchula Basin caves the number of basalt, andesite, argillite etc. raw materials are quite big. Since 130 000 a percent of the flint raw-material is increasing dramatically. Flint is an almost lonely dominated raw-material in Western Georgia during thousand years. Since approximately 50 000 ago the first obsidians brought from the South Georgia, appeared in Western Georgia. Similar situation has been detected by us in Eastern Georgia during our excavations of Ziari and Pkhoveli open-air sites. The early Lower Paleolithic layers are extremely rich by limestone artifacts while the flint raw-materials are dominated in the Middle Paleolithic layers. Study of these issues is possible to achieve across chronologies, the origins of the sources of raw-materials, the sites and regions. By merging archaeology with anthropology, geology and geography we are able to acquire outstanding insights about those populations. New approach to the Paleolithic stone materials, newly found Paleolithic quarries gave us an opportunities to try to achieve some results for understanding of the behavior of Paleolithic populations, geology and

  5. Potential of Technogenic Mineral Raw Materials in Russia and the Issues of its Rational Use

    Larisa Ivanovna Goncharova

    2015-11-01

    Full Text Available The increasing negative impact of mining waste on natural ecosystems often leads to their irreversible destruction, a trend that is gradually becoming global. The particular relevance of the research is explained, on the one hand, by the possibilities of minimization of specific volumes of formation of mining waste in all types of industries; on the other hand, by the possibilities of maximization of comp rehensive use of their valuable components as secondary material resources on an economically rational basis and the possibilities of restoring the disturbed natural environment. The rational use of natural and technogenic mineral raw materials is greatly facilitated by the geological exploration and geological-economic evaluation of the resources, which requires the development of specific methodological approaches to the economic justification of resource estimation parameters for outlining and calculating the multicomponent commercial reserves of raw materials and separate valuable components in them. Analysis shows that researchers’ opinions on a number of methodological principles of sustainable mining, complex processing of multicomponent materials are often contradictory. Scientific publications do not consider the issue of the price valuation of mining waste as secondary material resources. Mining waste processing should be considered as an important part of the overall socio-ecological-economic system for rational nature management. The analysis of the existing practice of using the mining waste should be based on the system approach and take into consideration geological, technological, economic, environmental and social characteristics throughout the cycle of production, combined processing and treatment of secondary waste according to the principle “from the earth to the earth”. The article identifies the main barriers to the recycling of mining wastes, proposes several methodological guidelines for the sustainable mining and

  6. A framework for evaluating the accessibility of raw materials from end-of-life products and the Earth's crust.

    Mueller, Sandra R; Wäger, Patrick A; Turner, David A; Shaw, Peter J; Williams, Ian D

    2017-10-01

    An increasing number of geochemically scarce metallic raw materials are entering into our lives via new technologies. A reversal of this trend is not foreseeable, leading to concerns regarding the security of their supply. However, the evaluation of raw material supply is currently hampered by inconsistent use of fundamental terminologies and incomplete assessment criteria. In this paper, we aim to establish a consistent framework for evaluating raw material supply from both anthropogenic and geological sources. A method for concept extraction was applied to evaluate systematically the use of fundamental terms in the evaluation of raw material supply. The results have shown that 'availability' is commonly used in raw material supply evaluations, whilst other researchers suggest that raw material supply should be evaluated based on 'accessibility'. It was revealed that 'accessibility' actually comprises two aspects: 'availability' and 'approachability'. Raw material 'approachability' has not previously been explicitly addressed at a system level. A novel, consistent framework for evaluating raw material supply was therefore developed. To demonstrate the application of the established framework, we evaluated the raw material supply of four rare earth element case studies. Three case studies are End-of-Life products (the anthroposphere) from Switzerland: (i) phosphors in fluorescent lamps, (i) permanent magnets in the drive motors of electric cars and (iii) fibre optic cable. The fourth case study source is the Earth's crust (the geosphere): Mount Weld deposit in Australia. The framework comprises a comprehensive evaluation of six components relating to raw material mining and processing: their geological knowledge, eligibility, technology, economic, societal and environmental impacts. Our results show that metals are not considered to be fully accessible in any of the case studies due to a lack of necessary technologies and potential societal and environmental

  7. Scalable preparation of high purity rutin fatty acid esters following enzymatic synthesis

    Lue, Bena-Marie; Guo, Zheng; Xu, Xuebing

    2010-01-01

    Investigations into expanded uses of modified flavonoids are often limited by the availability of these high purity compounds. As such, a simple, effective and relatively fast method for isolation of gram quantities of both long and medium chain fatty acid esters of rutin following scaled......-up biosynthesis reactions was established. Acylation reactions of rutin and palmitic or lauric acids were efficient in systems containing dried acetone and molecular sieves, yielding from 70–77% bioconversion after 96 h. Thereafter, high purity isolates (>97%) were easily obtained in significant quantities...

  8. Dissolution of high-purity lead and subsequent crystal growth during the preparation of corrosion coupons

    McGarvey, G.B. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); McDougall, T.E.; Owen, D.G. [Atomic Energy of Canada Limited, Pinawa, Manitoba (Canada)

    1997-07-01

    High-purity lead discs were prepared using several combinations of polishing, rinsing and ultrasonic treatment. Physical degradation of the lead surface and the premature generation and deposition of oxides on the surface were observed for certain combinations of preparation steps. Ultrasonic treatment of the discs was found to be particularly detrimental as it induced significant crystal growth and, in several instances, deterioration of the polished surface. Simple air drying of freshly rinsed discs also led to oxide formation on the surface after as short a time as 1 min. An effective method for preparing discs from high-purity lead is described. (author)

  9. Dissolution of high-purity lead and subsequent crystal growth during the preparation of corrosion coupons

    McGarvey, G.B.; McDougall, T.E.; Owen, D.G.

    1997-01-01

    High-purity lead discs were prepared using several combinations of polishing, rinsing and ultrasonic treatment. Physical degradation of the lead surface and the premature generation and deposition of oxides on the surface were observed for certain combinations of preparation steps. Ultrasonic treatment of the discs was found to be particularly detrimental as it induced significant crystal growth and, in several instances, deterioration of the polished surface. Simple air drying of freshly rinsed discs also led to oxide formation on the surface after as short a time as 1 min. An effective method for preparing discs from high-purity lead is described. (author)

  10. Raw materials evaluation and process development studies for conversion of biomass to sugars and ethanol

    Wilke, C.R.; Yang, R.D.; Sciamanna, A.S.; Freitas, R.P.

    1978-06-01

    A range of cellulosic raw materials in the form of agricultural crop residue was analyzed for chemical composition and assessed for potential yields of sugars through chemical pretreatment and enzymatic hydrolysis of these materials. Corn stover was used as a representative raw material for a preliminary process design and economic assessment of the production of sugars and ethanol. With the process as presently developed, 23 gallons of ethanol can be obtained per ton of corn stover at a processing cost of about $1.80 per gallon exclusive of by-product credits. The analysis shows the cost of ethanol to be highly dependent upon (1) the cost of the biomass, (2) the extent of conversion to glucose, (3) enzyme recovery and production cost and (4) potential utilization of xylose. Significant cost reduction appears possible through further research in these directions.

  11. Lime kiln dust as a potential raw material in portland cement manufacturing

    Miller, M. Michael; Callaghan, Robert M.

    2004-01-01

    In the United States, the manufacture of portland cement involves burning in a rotary kiln a finely ground proportional mix of raw materials. The raw material mix provides the required chemical combination of calcium, silicon, aluminum, iron, and small amounts of other ingredients. The majority of calcium is supplied in the form of calcium carbonate usually from limestone. Other sources including waste materials or byproducts from other industries can be used to supply calcium (or lime, CaO), provided they have sufficiently high CaO content, have low magnesia content (less than 5 percent), and are competitive with limestone in terms of cost and adequacy of supply. In the United States, the lime industry produces large amounts of lime kiln dust (LKD), which is collected by dust control systems. This LKD may be a supplemental source of calcium for cement plants, if the lime and cement plants are located near enough to each other to make the arrangement economical.

  12. Metallic oxide nano-clusters synthesis by ion implantation in high purity Fe10Cr alloy

    Zheng, Ce

    2015-01-01

    ODS (Oxide Dispersed Strengthened) steels, which are reinforced with metal dispersions of nano-oxides (based on Y, Ti and O elements), are promising materials for future nuclear reactors. The detailed understanding of the mechanisms involved in the precipitation of these nano-oxides would improve manufacturing and mechanical properties of these ODS steels, with a strong economic impact for their industrialization. To experimentally study these mechanisms, an analytical approach by ion implantation is used, to control various parameters of synthesis of these precipitates as the temperature and concentration. This study demonstrated the feasibility of this method and concerned the behaviour of alloys models (based on aluminium oxide) under thermal annealing. High purity Fe-10Cr alloys were implanted with Al and O ions at room temperature. Transmission electron microscopy observations showed that the nano-oxides appear in the Fe-10Cr matrix upon ion implantation at room temperature without subsequent annealing. The mobility of implanted elements is caused by the defects created during ion implantation, allowing the nucleation of these nanoparticles, of a few nm in diameter. These nanoparticles are composed of aluminium and oxygen, and also chromium. The high-resolution experiments show that their crystallographic structure is that of a non-equilibrium compound of aluminium oxide (cubic γ-Al 2 O 3 type). The heat treatment performed after implantation induces the growth of the nano-sized oxides, and a phase change that tends to balance to the equilibrium structure (hexagonal α-Al 2 O 3 type). These results on model alloys are fully applicable to industrial materials: indeed ion implantation reproduces the conditions of milling and heat treatments are at equivalent temperatures to those of thermo-mechanical treatments. A mechanism involving the precipitation of nano-oxide dispersed in ODS alloys is proposed in this manuscript based on the obtained experimental results

  13. Calibration curves of a PGNAA system for cement raw material analysis using the MCNP code

    Oliveira, Carlos; Salgado, Jose

    1998-01-01

    In large samples, the γ-ray count rate of a prompt gamma neutron activation analysis system is a multi-variable function of the elemental dry composition, density, water content and thickness of the material. The experimental calibration curves require tremendous laboratory work, using a great number of standards with well-known compositions. Although a Monte Carlo simulation study does not avoid the experimental calibration work, it reduces the number of experimental calibration standards. This paper is part of a feasibility study for a PGNAA system for on-line continuous characterisation of cement raw material conveyed on a belt (Oliveira, C., Salgado, J. and Carvalho, F. G. (1997) Optimisation of PGNAA instrument design for cement raw materials using the MCNP code. J. Radioanal. Nucl. Chem. 216(2), 191-198; Oliveira, C., Salgado, J., Goncalves, I. F., Carvalho, F. G. and Leitao, F. (1997a) A Monte Carlo study of the influence of geometry arrangements and structural materials on a PGNAA system performance for cement raw materials analysis. Appl. Radiat. Isot. (accepted); Oliveira, C., Salgado, J. and Leitao, F. (1997b) Density and water content corrections in the gamma count rate of a PGNAA system for cement raw material analysis using the MCNP code. Appl. Radiat. Isot. (accepted).]. It reports on the influence of the density, mass water content and thickness on the calibration curves of the PGNAA system. The MCNP-4A code, running in a Pentium-PC and in a DEC workstation, was used to simulate the PGNAA configuration system

  14. Biodiesel production using calcium manganese oxide as catalyst and different raw materials

    Dias, Joana Maia; Conceição Machado Alvim-Ferraz, Maria; Fonseca Almeida, Manuel; Méndez Díaz, José Diego; Sánchez Polo, Manuel; Rivera Utrilla, José

    2013-01-01

    Highlights: ► Biodiesel production using a calcium manganese oxide catalyst was studied. ► The active specie was Ca 0.9 Mn 0.1 O and its deactivation occurred by hydration. ► The studied catalyst presented lower activation temperature than CaO. ► Biodiesel production and quality using different raw materials is reported. ► Compared to the conventional process, biodiesel water content improved. - Abstract: The use of heterogeneous catalysts for biodiesel production aims to simplify the production process as well as to reduce purification costs and related environmental impacts. Calcium manganese oxide was recently identified by the authors as an interesting heterogeneous catalyst for biodiesel production from animal fat; however, the difference between this and other catalysts, the catalyst activation/deactivation mechanisms, its behaviour in the synthesis using different raw materials as well as the impacts of its use on product quality remained unclear. Therefore, the present work: (i) compared biodiesel production using calcium manganese oxide and other catalysts (CaO and NaOH); (ii) studied the reasons leading to activation/deactivation of the heterogeneous catalyst; (iii) analysed biodiesel heterogeneous synthesis using calcium manganese oxide and different raw materials (lard, waste frying oil and a mixture); and (iv) evaluated raw material and catalyst impact on the product quality. Considering the use of different catalysts, the results showed that, after 8 h of reaction, product purity was similar using the different catalysts, being 92.5 wt.% using both NaOH and calcium manganese oxide and 93.8 wt.% using CaO. The active species of the heterogeneous catalysts were CaO, in the case of calcinated calcium carbonate, and Ca 0.9 Mn 0.1 O, in the case of calcinated calcium manganese oxide. Because the deactivating species were different for both catalysts, the calcium manganese oxide required lower activation temperature, which should be an advantage

  15. Energy and raw material potentials of wood residue in the Pacific Coast States: a summary of a preliminary feasibility investigation.

    John B. Grantham; Eldon Estep; John M. Pierovich; Harold Tarkow; Thomas C. Adams

    1974-01-01

    Results are reported of a preliminary investigation of feasibility of using wood residue to meet energy and raw material needs in the Pacific Coast States. Magnitude of needs was examined and volume of logging-residue and unused mill residue was estimated. Costs of obtaining and preprocessing logging residue for energy and pulp and particle board raw material were...

  16. Raw materials in Africa and aspects of their utilisation; Rohstoffe in Afrika und Aspekte zu ihrer Nutzung

    Leonhardt, Joachim [Dr. Leonhardt Consulting, Essen (Germany)

    2011-03-15

    Consideration of raw materials in Africa and aspects of their utilisation refers not only to raw materials and their use, but also quite importantly to the prevailing situation in Africa itself and with regard to the population, the economic situation and also the commitment of other countries. (orig.)

  17. Estimation of raw material performance in mammalian cell culture using near infrared spectra combined with chemometrics approaches.

    Lee, Hae Woo; Christie, Andrew; Liu, Jun Jay; Yoon, Seongkyu

    2012-01-01

    Understanding variability in raw materials and their impacts on product quality is of critical importance in the biopharmaceutical manufacturing processes. For this purpose, several spectroscopic techniques have been studied for raw material characterization, providing fast and nondestructive ways to measure quality of raw materials. However, investigations of correlation between spectra of raw materials and cell culture performance have been scarce due to their complexity and uncertainty. In this study, near-infrared spectra and bioassays of multiple soy hydrolysate lots manufactured by different vendors were analyzed using chemometrics approaches in order to address variability of raw materials as well as correlation between raw material properties and corresponding cell culture performance. Principal component analysis revealed that near-infrared spectra of different soy lots contain enough physicochemical information about soy hydrolysates to allow identification of lot-to-lot variability as well as vendor-to-vendor differences. The identified compositional variability was further analyzed in order to estimate cell growth and protein production of two mammalian cell lines under the condition of varying soy dosages using partial least square regression combined with optimal variable selection. The performance of the resulting models demonstrates the potential of near-infrared spectroscopy as a robust lot selection tool for raw materials while providing a biological link between chemical composition of raw materials and cell culture performance. Copyright © 2012 American Institute of Chemical Engineers (AIChE).

  18. Farmers as providers of raw materials and energy. Proceedings; Der Landwirt als Energie- und Rohstoffwirt. Konferenzbeitraege

    NONE

    2008-07-01

    Within the 10th EUROSOLAR conference at 14th to 15th April, 2008, at Leipzig (Federal Republic of Germany), the following lectures were held: (a) Bioenergy in the Federal Republic of Germany: Potentials, state of the art and perspectives (M. Kaltschmitt, V. Lenz, D. Thraen); (b) Chances and risks of the energy production from biomass in rural area (G. Thalheim); (c) To the compatibility of utilizing bio energy and environmental preservation (K. Mueschen); (d) Biorefinery systems - industrial material use of regenerative raw materials (B. Kamm); (e) Agriculturists and forestry experts as producers of raw material - current risks and new chances (H. Fischer); (f) Potentials of the improvement of productivity by means of an expansion of options of useful plants (K. Goedeke); (g) Farmers as providers of energy and raw materials (H. Loick); (h) Problems and challenges of the utilization of biomass (P. Volkmer); (i) Energetic recycling management (G. Mehler); (j) Pure fuels instead of fuel mixtures - The farmer as providers of energy and raw materials (P. Schrum); (k) Feed and distribution of bio-natural gas from the view of a regional provider (J. Horn); (l) Biogasification and feed into natural gas networks - by the example of BGA Darmstadt-Wixhausen (M. Schlegel); (m) The right framework for the feed of bio methane into natural gas nets (S. Reichelt); (n) Virtual power plants - Efficient option of the local energy production (G. Weissmueller); (o) The role of bio energy in the power mix renewable energies (R. Bischof); (p) The autonomous power supply - from the bio energy village to the autonomous solar energy village (K. Scheffer); (q) Bio energy villages at the Lake Constance - Model projects for the rural area (B. Mueller); (r) Bio energy region Mureck / Steiermark (K. Totter); (s) The bio energy in the current German legislation process (H.-J. Fell).

  19. Prospects of rice straw as a raw material for paper making.

    Kaur, Daljeet; Bhardwaj, Nishi Kant; Lohchab, Rajesh Kumar

    2017-02-01

    Pulp and paper mills are indispensable for any nation as far as the growth of the nation is concerned. Due to fast growth in population, urbanization and industrialization, the demand and consumption of paper has increased tremendously. These put high load on our natural resources and force the industry to look for alternative raw material. Rice straw is a lignocellulosic material abundantly available in wood short countries like China, India, Bangladesh, etc. and can be used as raw material for this industry. Open burning of rice straw releases noxious green house gases to the air and poses serious threats to global air chemistry and human health. So, it is a dual benefit option (for farmers and industries) to use rice straw as a raw material in pulp and paper industry. Organosolv pulping using acids are the prominent choices of researchers to convert this residue into valuable pulp but in developed countries only. Developing world favours the soda and soda-AQ processes as these are economical. As a virtue of less lignin content in comparison to wood, rice straw requires less harsh conditions for cooking and can be easily pulped. Bleaching is a crucial step of paper making but also responsible for causing water pollution. Many studies revealed that during the process more than 500 chlorinated compounds are released that are highly toxic, bioaccumulative and carcinogenic in nature. Most of the industries over the globe switch on to the elemental chlorine free short sequence bleaching methods using chlorine dioxide, hypochlorite and hydrogen peroxide. This paper presented the effective need of ecofriendly, economically reliable pulping and bleaching sequences in case of rice straw to eliminate the problems of chlorinated compounds in wastewater of paper mills. Such approach of using waste as a raw material with its environmentally safe processing for making paper can prove to be valuable towards sustainable growth. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Radioactivity and associated radiation hazards in ceramic raw materials and end products.

    Viruthagiri, G; Rajamannan, B; Suresh Jawahar, K

    2013-12-01

    Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of (226)Ra, (232)Th and (40)K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants.

  1. Radioactivity and associated radiation hazards in ceramic raw materials and end products

    Viruthagiri, G.; Rajamannan, B.; Suresh Jawahar, K.

    2013-01-01

    Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of 226 Ra, 232 Th and 40 K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants. (authors)

  2. Raman, Infrared, and Laser-Induced Breakdown Spectroscopy Identification of Particles in Raw Materials.

    Lee, Kathryn; Lankers, Markus; Valet, Oliver

    2018-02-01

    Raw materials need to be of a certain quality with respect to physical and chemical composition. They also need to have no contaminants, including particles, because these could indicate raw material impurities or contaminate the product. Particle identification allows determination of process conditions that caused them and whether the quality of the final product is acceptable. Particles may appear to the eye to be very different things than they actually are. They may be coated with the raw material and may consist of several components; therefore, chemical and elemental analyses are required for accuracy in proper identification and definitive information about their source. Thus, microscope versions of Raman spectroscopy, laser-induced breakdown spectroscopy (LIBS), and infrared (IR) spectroscopy are excellent tools for identifying particles in materials. Those tools are fast and accurate, and can provide chemical and elemental composition as well as images that can aid identification. The micro-analysis capabilities allow for easy analysis of different portions of samples so that multiple components can be identified and sample preparation can be reduced or eliminated. The differences in sensitivities of Raman and IR spectroscopies to different functional groups as well as the elemental analysis provided by LIBS and the image analysis provided by the microscopy makes these complementary techniques and provides the advantage of identifying various chemical components. Proper spectral searching techniques and interpretation of the results are important for interpretation and identification of trace contaminants.

  3. Rambutan Seed (Nephelium Lappaceum L.) Optimization as Raw Material of High Nutrition Value Processed Food

    Wahini, M.; Miranti, M. G.; Lukitasari, F.; Novela, L.

    2018-02-01

    Rambutan (Nephelium Lappaceum L.) is a plant that identical with Southeast Asian countries, in some areas of Indonesia no exception, but rambutan seed is considered as a waste. Therefore, it needs to be optimized into raw materials of food and processed with high nutritional value and has economic value. The purpose of this research were: 1) to find the best rambutan seed immersion formula; 2) to know the nutritional value of the best immersed rambutan seed; 3) to produce raw material and various processed of rambutan seed product. The research method was quasi experiment with 6 treatments and 2 factorial design, materials for immersion was NaCl and Ca(OH)2. The results showed that: 1) the best rambutan seed immersion formula was using Ca(OH)2; 2) the best rambutan seed contains 1,6 ash, 31,2 protein, 26,9 fat; 3) the best rambutan seed produce flour and processed of seasoned nuts. This research indicates that rambutan seed is very potential to be an alternative high-value raw materials.

  4. The determination of minor amounts of rare earth elements in high purity earth oxides by HPLC/IDMS

    Stijfhoorn, D.E.; Stray, H.; Hjelmseth, H.

    1991-05-01

    Since the early seventies isotopic dilution mass spectrometry (IDMS) has been used at Institutt for energiteknikk, Kjeller, Norway for determination and certification of rare earth elements in high purity Y 2 O 3 . These lanthanides have, during the last few decades, become more widely used in highly specialized technology. High purity, quality 4 N (99.99%) or even 5 N materials are needed for phosphors, lasers, optical fibers, X-ray films, and in contrast fluids for magnetic resonance imaging (MRI). However, in a matrix constisting primarily of a single lanthanide, IDMS alone will not be effective due to isobaric interferences from the main elements or the mono-oxides formed in the ion source. On the other hand, high performance liquid chromatography (HPLC) may be used, but the detection limit will be in the order of 5 to 10 ppm/W. In this work a combination of HPLC and IDMS has been used to lower the detection limit to 1 ppm/W, where the sample is spiked before separation by HPLC, followed by IDMS analysis of the HPLC- fractions. In some cases the HPLC-process has to be repeated to remove the main element completly. Results are presented for Dy 2 O 3 and Nd 2 O 3 , but similar separating procedures can be applied for other rare earth oxides. 3 refs., 2 figs. 2 tabs

  5. WATER-JET CUTTING MACHINE NOW AVAILABLE FROM THE CERN RAW MATERIALS STORES

    2007-01-01

    The CERN Raw Materials Stores has recently acquired a new water-jet cutting machine. The machine is capable of cutting all types and shapes of materials up to 70 mm in thickness, with an accuracy of +/- 0.1mm/m. For the time being, users requiring materials to be cut should supply drawings in DXF, DWG or IGES (AutoCad) file format. The machine will be operational as of 1st October 2007. The Stores Team Paulo Dos Santos FI-LS-MM 72308

  6. High-Purity Fe3S4 Greigite Microcrystals for Magnetic and Electrochemical Performance

    Li, Guowei; Zhang, Baomin; Yu, Feng; Novakova, Alla A.; Krivenkov, Maxim S.; Kiseleva, Tatiana Y.; Chang, Liao; Rao, Jiancun; Polyakov, Alexey O.; Blake, Graeme R.; de Groot, Robert A.; Palstra, Thomas T. M.

    2014-01-01

    High-purity Fe3S4 (greigite) microcrystals with octahedral shape were synthesized via a simple hydrothermal method using a surfactant. The as-prepared samples have the inverse spinel structure with high crystallinity. The saturation magnetization (M-s) reaches 3.74 mu(B) at 5 K and 3.51 mu(B) at

  7. Effect of microplastic deformation on the electron ultrasonic absorption in high-purity molybdenum monocrystals

    Pal'-Val', P.P.; Kaufmann, Kh.-J.

    1983-01-01

    The low temperature (100-6 K) linear absorption of ultrasound (88 kHz) by high purity molybdenum single crystals have been studied. Both unstrained samples and samples sub ected to microplastic deformation (epsilon 0 approximately 10 -4 , during 10 min, at 6 K. A new relaxation peak of absorption at 10 K has been found in strained samples

  8. Variation of low temperature internal friction of microplastic deformation of high purity molybdenum single crystals

    Pal-Val, P.P.; Kaufmann, H.J.

    1984-01-01

    Amplitude and temperature spectra of ultrasound absorption in weakly deformed high purity molybdenum single crystals of different orientations were measured. The results were discussed in terms of parameter changes related to quasiparticle or dislocation oscillations, respectively, dislocation point defect interactions as well as defect generation at microplastic deformation. (author)

  9. Tests of ball bearing used in high-temperature and high-purity water

    Leng Chengmu; Hao Shouxin.

    1987-01-01

    According to the particular conditions and the operation environments in high-temperature and high-purity water, the test content and the measurement instrumentation for the ball bearing were defined. Through various tests, operational performances of the bearing have preliminarily been understood. It provided some useful information for the engineering application of the bearing

  10. Perspectives of data-driven LPV modeling of high-purity distillation columns

    Bachnas, A.A.; Toth, R.; Mesbah, A.; Ludlage, J.H.A.

    2013-01-01

    Abstract—This paper investigates data-driven, Linear- Parameter-Varying (LPV) modeling of a high-purity distillation column. Two LPV modeling approaches are studied: a local approach, corresponding to the interpolation of Linear Time- Invariant (LTI) models identified at steady-state purity levels,

  11. Operation of a high-purity silicon diode alpha particle detector at 1.4 K

    Martoff, C.J.; Kaczanowicz, E.; Neuhauser, B.J.; Lopez, E.; Zhang, Y.; Ziemba, F.P.

    1991-01-01

    Detection of alpha particles at temperatures as low as 1.4 K was demonstrated using a specially fabricated Si diode. The diode was 475 mm 2 by 0.280 mm thick, fabricated from high-purity silicon with degenerately doped contacts. This is an important step toward development of dual-mode (ionization plus phonon) silicon detectors for low energy radiation. (orig.)

  12. High-temperature mechanical properties of high-purity 70 mass% Cr-Fe alloy

    Asahina, M.; Harima, N.; Takaki, S.; Abiko, K. [Tohoku Univ., Sendai (Japan). Inst. for Materials Research

    2002-01-16

    An ingot of high-purity 70 mass% Cr-Fe alloy was prepared by high-frequency induction melting in a high-purity argon atmosphere using a cold copper crucible. Its tensile properties such as hot-ductility and tensile strength were measured, and compared with the results for a high-purity 50 mass% Cr-Fe alloy, a high-purity 60 mass% Cr-Fe alloy and a Ni-based super-alloy. The formation of {sigma}-phase was also examined. The purity of a 70Cr-Fe alloy (70 mass% Cr-Fe alloy) ingot is more than 99.98 mass% and the total amount of gaseous impurities (C, N, O, S, H) in the 70Cr-Fe alloy is 69.9 mass ppm. The strength of the 70Cr-Fe alloy is higher than those of the 60Cr-Fe alloy and the 50Cr-Fe alloy at the temperatures between 293 and 1573 K, without decrease in ductility with increasing Cr content. The 70Cr-Fe alloy also possesses excellent high-temperature ductility. The {sigma}-phase was not observed after aging of 3.6 Ms at 873 K. Consequently, the 70Cr-Fe alloy is an excellent alloy as the base of super heat-resistant alloys. (orig.)

  13. State-of-the-art in analytical characterization of high purity solid ...

    Facilities and some results of several spectroscopic methods which have potential applications in the field of analysis of solid high purity substances and which have been elaborated in Russia, will be discussed in this paper. Laser nondispersive atomic fluorescence method with glow discharge cathode sputtering atomiser, ...

  14. Fabrication and research of high purity germanium detectors with abrupt and thin diffusion layer

    Rodriguez Cabal, A. E.; Diaz Garcia, A.

    1997-01-01

    A different high purity germanium detector's fabrication method is described. A very thin diffusion film with an abrupt change of the type of conductivity is obtained. The fine diffusion layer thickness makes possibly their utilization in experimental systems in which all the data are elaborated directly on the computer. (author) [es

  15. Variation of low temperature internal friction of microplastic deformation of high purity molybdenum single crystals

    Pal-Val, P.P. (AN Ukrainskoj SSR, Kharkov. Fiziko-Tekhnicheskij Inst. Nizkikh Temperatur); Kaufmann, H.J. (Akademie der Wissenschaften der DDR, Berlin)

    1984-08-01

    Amplitude and temperature spectra of ultrasound absorption in weakly deformed high purity molybdenum single crystals of different orientations were measured. The results were discussed in terms of parameter changes related to quasiparticle or dislocation oscillations, respectively, dislocation point defect interactions as well as defect generation at microplastic deformation.

  16. Effect of the microstructure on electrical properties of high-purity germanium

    Podkopaev, O. I.; Shimanskii, A. F.; Molotkovskaya, N. O.; Kulakovskaya, T. V.

    2013-05-01

    The interrelation between the electrical properties and the microstructure of high-purity germanium crystals has been revealed. The electrical conductivity of polycrystalline samples increases and the life-time of nonequilibrium charge carriers in them decreases with a decrease in the crystallite sizes.

  17. Preparation of uranium-plutonium mixed nitride pellets with high purity

    Arai, Yasuo; Shiozawa, Ken-ichi; Ohmichi, Toshihiko

    1992-01-01

    Uranium-plutonium mixed nitride pellets have been prepared in the gloveboxes with high purity Ar gas atmosphere. Carbothermic reduction of the oxides in N 2 -H 2 mixed gas stream was adopted for synthesizing mixed nitride. Sintering was carried out in various conditions and the effect on the pellet characteristics was investigated. (author)

  18. Conception for the protection of mineable raw materials in the Land of Brandenburg (Germany)

    Kopf, M.

    1995-01-01

    The pit and quarry industry in Brandenburg will within a few years the same importance as the lignite industry. Both industries together may have up to 20 000 employees beyond the year 2000. The same number of employees could result in the enterprises of local and other subcontractors and mine suppliers. The government of Brandenburg creates at present the legal prerequisites to secure the supply with mineable raw materials. The regulation of the protection of mineable raw materials is proposed to be realised within the scope of the second plan for the development of the country, and within the regional plannings. The protection of the basic conditions for mining industries is a permanent task for administration and politics. By encouraged engagement in the case of opposed interests, those of mining can be considered with acceptable results provided the parties are ready to compromise. (orig.) [de

  19. High yield CTMP fibres as a possibility of the more efficient yield of wood raw material

    Klašnja Bojana A.

    2004-01-01

    Full Text Available The evident shortage of wood as a raw material has become a limiting factor in the pulp and paper industry which is the greatest consumer of wood in Europe. The situation in our country is similar. During the few past years, the production of poplar and willow pulpwood was 220.000 m3 per year, which is insufficient for the planned increase in the production of sulphate pulp (175.000 tons till 2005. This paper deals with the aspects of the more efficient yield of raw material, based on the significantly higher yield of CTMP fibres, as well as with the significance of the lower adverse effect on the environment. It also analyses the conditions of production and the quality of the obtained fibres, as a possible substitute for chemical pulp and secondary fibres in papers of different quality. The main reasons for the production and use of CTMP fibres in our country are reported.

  20. Energies and raw material. Annual report; Energies et matieres premieres. Rapport annuel

    NONE

    1999-07-01

    The annual report of the french General Direction of the Energy and the Raw Material (DGEMP) deals with the energy policy. The following subjects are analysed: the french program of fight against the global warming; the biogas; the radioactive wastes management program; the french nuclear industry re-organization; Tchernobyl; the electric power and gas public service; the risk prevention concerning the electric power production; the international Gaz De France protocol; the closing of the Ales mine; the cooperation ELF and TOTAL; the french para-petroleum industry; the raw material prices; the french mining situation; the french energy policy audit by the AIE; the energy accidents of december. The DGEMP organization chart with contacts and the publications are also included. (A.L.B.)

  1. Aspects of investment protection in the case of raw material projects; Aspekte des Investitionsschutzes bei Rohstoffprojekten

    Wolkewitz, Mathias [Wintershall Holding GmbH, Kassel (Germany). Bereich Recht, Steuern und Versicherungen; TU Clausthal (Germany). Inst. fuer Energierecht

    2011-04-15

    Addressing the question of investment protection currently is of particular importance under the tree aspects: (a) Due to the financial crisis and economic crisis, foreign investment in the years 2008 and 2009 have been drastically reduced; (b) There is a growing critique at the system of international investment protection; (c) For the first time, the Articles 206 and 207 of the Treaty of Lisbon of the European Union show a competence for foreign direct investment. These three aspects seem partly contradictory, but have a considerable changing potential in the area of investment protection. The author of the contribution under consideration describes the tools of investment protection as those are used for raw material projects. Subsequently the author picks out investment protection agreements and deals with some aspects that are important for practical applications in business companies. Raw material projects are projects for the exploration and production of oil and gas in foreign states.

  2. The use of foresight methods in strategic raw materials intelligence - an international review

    Konrat Martins, Marco Antonio; Bodo, Balazs; Falck, Eberhard

    2017-04-01

    Foresight methods are systematic attempts to look into the longer term future of science, society, economy and technology. There is a range of tools and techniques that can be used individually or combined, most commonly classified into qualitative, quantitative or semi-quantitative methods, that follow an exploratory or normative approach. These tools can help to identify the longer term visions, orienting policy formulation and decisions, triggering actions, among other objectives. There is an identified lack of European strategic foresight knowledge in the raw materials domain. Since the European Raw Materials Initiative was launched in 2008, the EU has been attempting to overcome challenges related to the future access of non-energy and non-agricultural raw materials. In this context, the ongoing H2020 project, MICA (Mineral Intelligence Capacity Analysis, Grant Agreement No. 689648), has been launched to answer to stakeholders needs by consolidating relevant data, determining relevant methods and tools, and investigating Raw Materials Intelligence options for European mineral policy development, all tailored to fit under the umbrella of a European Raw Materials Intelligence Capacity Platform (EU-RMICP). As part of the MICA activities, an assessment of best practices and benchmarks of international raw materials foresight case studies has been carried out in order to review how EU and non-EU countries have employed foresight. A pool of 30 case studies has been collected and reviewed internationally, one third of which were selected for detailed assessment. These were classified according to their background and goals, in function of methods employed, and to the purpose of each method in the study: a total of 12 different methods were identified in these studies. For longer time frames, qualitative predictive methods such as Scenario Development have been repeatedly observed for mineral raw materials foresight studies. Substantial variations were observed in

  3. Freezing of meat raw materials affects tyramine and diamine accumulation in spontaneously fermented sausages.

    Bover-Cid, Sara; Miguelez-Arrizado, M Jesús; Luz Latorre Moratalla, L; Vidal Carou, M Carmen

    2006-01-01

    Biogenic amine accumulation was studied in spontaneously fermented sausages (Fuet) manufactured from unfrozen-fresh meat (U-sausages) and frozen-thawed meat (F-sausages). The aim was to investigate whether the frozen storage of raw materials affects the microbial composition and its aminogenic activity during sausage fermentation. Tyramine was the major amine in all sausages. Although the final levels were similar, tyramine accumulated more rapidly in F-sausages, which contained putrescine as the second amine. By contrast, U-sausages accumulated much more cadaverine than putrescine. F-sausages showed a slightly lower pH and free amino acid content as well as higher counts of technological flora (lactic acid and gram positive catalase positive bacteria) and lower counts of enterobacteria. Therefore, to freeze the meat raw materials for few days before sausage manufacture could be a useful practice, especially for the artisan fermented sausages (without starter), because it helps to reduce enterobacteria development and cadaverine production.

  4. The use of rapid spectroscopic screening methods to detect adulteration of food raw materials and ingredients

    Sørensen, Klavs Martin; Khakimov, Bekzod; Engelsen, Søren Balling

    2016-01-01

    with chemometrics appears to be an efficient first choice for testing incoming raw materials and ingredients in the food production. However, in order to realize its full potential, it is necessary to move away from the current thoughts at the Parnassus, namely the targeted approach. This review will focus......International trade in food commodities will continue to increase and the complex food supply chains make adulteration detection and traceability a technical, logistical and financial challenge. There is no magic solution for adulteration testing, but NIR spectroscopy in combination...... on the exploitation of the capability of NIR spectroscopy to fingerprint incoming raw materials and ingredients as an integrated part of the industry's self-monitoring program typically called process analytical technology....

  5. Characterisation of Cements From Dominantly Volcanic Raw Materials of the Carpathian Bend Zone

    Halmagy Timea

    2016-12-01

    Full Text Available This paper presents the results of laboratory investigations regarding the production of cements from local raw materials, such as limestone from Varghis, gypsum from Nucsoara, basaltic scoria from Racosul de Jos, volcanic tuff from Racosul de Sus, diatomite from Filia, and red mud from Oradea. The raw mixtures, based on modified Bogue calculations, contain limestone, gypsum, and one or two of the above-mentioned materials. The cements resulted from clinker grinding in a laboratory gas furnace at 1260-1300 °C, with one hour at the peak temperatures, and were characterised for Blaine specific surface area, specific density, and mineral phases. Physico-mechanical properties, such as water content for normal consistency, setting time, soundness, and compressive strength were also determined. Results show that these cements contain belite, ferrite, calcium sulphoaluminate, anhydrite, and some minor compounds.

  6. Selected scientific articles. (Investigations in the field of hydrides chemistry and mineral raw materials processing)

    Mirsaidov, U.M.

    2013-01-01

    Articles, included in the present book are covering period 1977-2013 y. The main scientific articles in the field of power-consuming substances, mineral raw-materials and wastes reprocessing, including uranium industry wastes are collected. Scientific works on hydrogen chemistry which carried out basically bu U.M. Mirsaidov without co-authors are considered. These works are on aluminium hydrides and borohydrides lanthanides. Besides, author's popular-science articles on research carried out by Academy of Sciences during the period when he was the President of Academy of Sciences of the Republic of Tajikistan (1995-2005) are included. Mineral raw materials and wastes reprocessing results are given as well. The book is intended for engineer and technical staff, those working in the field of hydrogen chemistry, hydrometallurgy workers, engineering chemists as well as for PhD, post graduate students and students of appropriate profiles.

  7. Exploiting epoxidized natural rubber latex (ENRL) as a starting raw material for latex-based products

    Siti Nor Qamarina, M.; Fatimah Rubaizah, M. R.; Nurul Suhaira, A.; Norhanifah, M. Y.

    2017-12-01

    Epoxidized natural rubber latex (ENRL) is a chemically modified natural rubber latex produced from epoxidation process that involves usage of organic peracids. Conversion of the ENRL into dry rubber products has been known to exhibit many beneficial properties, however limited published works were found on diversifiying the ENRL latex-based products applications. In this preliminary work, different source of raw materials and neutralization systems were investigated. The objective was to explore possibilities in producing distinctive ENRL. Findings have demonstrated that different source of raw materials and neutralization systems influenced the typical ENRL specifications, stability behavior and particle size distribution. Morphological observations performed on these ENRL systems appeared to agree with the ENRL characteristics achieved. Since experimenting these two main factors resulted in encouraging ENRL findings, detailed work shall be further scrutinized to search for an optimum condition in producing marketable ENRL specifically for latex-based products applications.

  8. Determination of uranium in natural waters and high-purity aluminum by flow-injection on-line preconcentration and ICP-MS detection

    Seki, Tatsuya; Oguma, Koichi

    2004-01-01

    A flow injection method has been developed for the determination of uranium is natural waters and high-purity aluminum by use of on-line preconcentration on a U/TEVA TM column and ICP-MS detection. The sample solution prepared as a nitric acid solution in 3 mol l -1 was passed through the U/TEVA TM column to collect uranium and uranium adsorbed was eluted with 0.1 mol l -1 nitric acid. The effluent was introduced directly into the nebulizer of the ICP-MS and 238 U was measured. The detection limit, calculated as 3-times the standard deviation of the background noise, was 3pg and the sample throughput was about 10 per hour. The proposed method was successfully applied to the determination of uranium in river-water reference materials, a seawater reference material and high-purity aluminum reference materials. (author)

  9. Raw material boom in an industrial country. Rohstoffboom in einem Industrieland

    Enders, K S

    1984-01-01

    First of all, a theoretical investigation is carried out to discover under which conditions a raw material boom displaces traditional sectors of industry, and which groups win and lose in the process. Subsequently, the peculiarities of the adaption process induced by the boom are analysed. Particular attention is paid to the possibility of transition (short-term) unemployment (Dutch disease). In conclusion, Norway's experiences in the oil and gas boom in the North Sea ar described and then compared with theoretical statements.

  10. Regenerative raw materials. High technology without end; Nachwachsende Rohstoffe. Spitzentechnologie ohne Ende

    NONE

    2011-11-03

    In recent years, the use of renewable raw materials has developed rapidly. Meanwhile, biomass is one of the most important renewable energy source and a serious alternative to fossil fuel-based industry. The brochure under consideration presents an insight into the complex and promising topic ''Renewable Resources''. In particular, the areas in which renewable resources already are established as well as areas that need to be extended in the future are described.

  11. 1.2. X-ray phase analysis of borosilicate raw material

    Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

    2015-01-01

    Present article is devoted to X-ray phase analysis of borosilicate raw material. The thermo gram of initial borosilicate ore was considered. The X-ray pattern of initial danburite of Ak-Arhar Deposit was considered as well. The X-ray pattern of danburite of Ak-Arhar Deposit after pre-baking was studied. The X-ray pattern of initial danburite concentrate was studied as well.

  12. Utilization of flotation wastes of copper slag as raw material in cement production

    Alp, I.; Deveci, H.; Suenguen, H.

    2008-01-01

    Copper slag wastes, even if treated via processes such as flotation for metal recovery, still contain heavy metals with hazardous properties posing environmental risks for disposal. This study reports the potential use of flotation waste of a copper slag (FWCS) as iron source in the production of Portland cement clinker. The FWCS appears a suitable raw material as iron source containing >59% Fe 2 O 3 mainly in the form of fayalite (Fe 2 SiO 4 ) and magnetite (Fe 3 O 4 ). The clinker products obtained using the FWCS from the industrial scale trial operations over a 4-month period were characterised for the conformity of its chemical composition and the physico-mechanical performance of the resultant cement products was evaluated. The data collected for the clinker products produced using an iron ore, which is currently used as the cement raw material were also included for comparison. The results have shown that the chemical compositions of all the clinker products including those of FWCS are typical of a Portland cement clinker. The mechanical performance of the standard mortars prepared from the FWCS clinkers were found to be similar to those from the iron ore clinkers with the desired specifications for the industrial cements e.g. CEM I type cements. Furthermore, the leachability tests (TCLP and SPLP) have revealed that the mortar samples obtained from the FWCS clinkers present no environmental problems while the FWCS could act as the potential source of heavy metal contamination. These findings suggest that flotation wastes of copper slag (FWCS) can be readily utilised as cement raw material due to its availability in large quantities at low cost with the further significant benefits for waste management/environmental practices of the FWCS and the reduced production and processing costs for cement raw materials

  13. Utilization of flotation wastes of copper slag as raw material in cement production.

    Alp, I; Deveci, H; Süngün, H

    2008-11-30

    Copper slag wastes, even if treated via processes such as flotation for metal recovery, still contain heavy metals with hazardous properties posing environmental risks for disposal. This study reports the potential use of flotation waste of a copper slag (FWCS) as iron source in the production of Portland cement clinker. The FWCS appears a suitable raw material as iron source containing >59% Fe(2)O(3) mainly in the form of fayalite (Fe(2)SiO(4)) and magnetite (Fe(3)O(4)). The clinker products obtained using the FWCS from the industrial scale trial operations over a 4-month period were characterised for the conformity of its chemical composition and the physico-mechanical performance of the resultant cement products was evaluated. The data collected for the clinker products produced using an iron ore, which is currently used as the cement raw material were also included for comparison. The results have shown that the chemical compositions of all the clinker products including those of FWCS are typical of a Portland cement clinker. The mechanical performance of the standard mortars prepared from the FWCS clinkers were found to be similar to those from the iron ore clinkers with the desired specifications for the industrial cements e.g. CEM I type cements. Furthermore, the leachability tests (TCLP and SPLP) have revealed that the mortar samples obtained from the FWCS clinkers present no environmental problems while the FWCS could act as the potential source of heavy metal contamination. These findings suggest that flotation wastes of copper slag (FWCS) can be readily utilised as cement raw material due to its availability in large quantities at low cost with the further significant benefits for waste management/environmental practices of the FWCS and the reduced production and processing costs for cement raw materials.

  14. Optimizing Pretreatment of Medicinal Raw Materials by RFC Plasma before Extraction

    O.Yu. Kuznetsova

    2016-06-01

    Full Text Available Optimization of the RF-plasma treatment modes of chaga raw materials using the Statistica 6.0 software package has been performed. Mathematical design has been carried out to calculate the optimum parameters of RF-plasma treatment using three plasma-forming gases – argon, air, and nitrogen. Plasma treatment of chaga raw materials has been undertaken at the constant parameters: pressure P = 30.0 Pa, anodic current J = 0.7 A, gas consumption G = 0.04 g/s; the variable parameters were power U = 5.0÷7.0 kV and treatment duration at the high-frequency capacitor category of the lowered pressure t = 30÷60 min. Optimization of four key parameters for extraction of chaga raw materials (solid residue, melanin yield, antioxidant activity of both extract and chaga melanin depending on the chosen plasma-forming gas (argon, air, or nitrogen has been achieved. The optimum modes of RF-plasma treatment allowing to obtain the extracts and melanin of chaga mushroom with the improved physicochemical and antioxidant characteristics have been calculated.

  15. New and non-traditional mineral raw materials deposits, perspectives of use

    Beyseev, O.; Beyseev, A.; Baichigasov, I.; Sergev, E.; Shakirova, G.

    1996-01-01

    Deposits of new and non-traditional kinds of mineral raw material are revealed, explored and prepared to industrial recovery in Kazakstan, that can be used in frames of conversion process to create new materials with unique properties, to prepare base for new technologies elaboration, and to achieve appreciable economic benefit. These deposits are located mostly in geographic and economic conditions of advanced infrastructure and mining works network, favorable for recovery.On the tests results the following is of heaviest interest: RHODUCITE, NEMALITE-CONTAINING CHRYSOTILE-ASBESTOS, NICKEL-CONTAINING SILICATE-ASBOLAN ORES, MEDICINAL MINERALS, SHUNGITES, FULLERENES, RAW QUARTZ MINERALS - the group of deposits containing 5 min tons of high quality quartz good for manufacture of cut-glass and fibre-optical articles, is explored in details. There are also deposits of other kinds of non-traditional strategic mineral raw material in the Republic of Kazakstan - natural fillers, that can be used in the national economy of the country and bring considerable economic benefit: chrysotile-asbestos, amphibole-asbestos, talk, vollastonite, tremolite, actinolite, vermiculite, zeolite, etc

  16. Raw material from the state of Rio Grande do Norte, Brazil, to obtain sandstone porcelain

    Sousa, Maria Rosimar de

    2009-01-01

    Currently, the production of the ceramic industry of the River Great of the North she is restricted to the manufacture of bricks and roofing tiles. development of new ceramic products of bigger added value, such as gres covering porcelanato, using regional raw materials is of basic importance for the growth of the local ceramic industry and economic development of the region. In this work, they had been studied raw materials as kaolin, sodico feldspato and quartz of the State of the Great River of the North for the attainment of an covering of the gres type porcelanato of base white.The ceramic masses had been prepared by the process saw humid. The body-of-tests they had been conformed by uniaxial prensagem of 40MPa, dried in 110 deg C and burnt between 1160 and 1240 deg, used a cycle of fast burning (approximately 60min.). The qualitative analysis of the formed phases disclosed silica, mullite e sodico feldspato after the sintering. The technological properties of burning evaluated they had been: linear retraction, water absorption, apparent specific mass, porosity and breaking strength to the flexal (shipment of 3 points). Results show that raw materials proceeding from the State of the Great River of North could be used in processes for gres porcelanato, therefore they present characteristics technological, similar chemistry, physics and to the standard of reference and the data of literature. (author)

  17. Multicriteria analysis of agricultural raw materials: A case study of BSBIOS and PETROBRAS BIOFUELS in Brazil

    Zonin, Valdecir José; Valle Antunes, José Antônio; Pinto Leis, Rodrigo

    2014-01-01

    Energy crises reverberate within societies and encourage worldwide change in this industry. In this context, Brazil has been consolidating the National Program for the Production and Use of Biodiesel (Programa Nacional de Produção e Uso do Biodiesel—PNPB). This article analyzes BSBIOS and PETROBRAS BIOFUELS, which is a company that is incorporated under the PNPB. After providing an overview, the manuscript focuses on the criteria used for the selection of the agricultural raw materials used in the biodiesel industry. A reference model that considered the economic, technological, and social dimensions was developed; these dimensions were analyzed in relation to the production matrices of the soybean, canola, sunflower, and castor plants. The company strategically opted to establish programs for promoting the production of only soybean and canola. In the short term, the company has accepted the evidence that the main source of raw materials is soybean production. This decision was made considering the multicriteria analysis that was developed, which involved a number of economic, technological, and social aspects. Consequently, this analysis used in the decision-making process exhibits both a macro (the national and international environment) and a micro perspective (the companies’ reality). - Highlights: • The economic viability of biodiesel production in Brazil hinges on crop production. • Biodiesel production in Brazil requires developing an efficient production chain. • Oleaginous crops will be diversified by creating a network of suppliers. • Raw material production is diversifying based on an analysis of relevant factors

  18. Fabrication and characterization of lithium orthosilicate pebbles using LiOH as a new raw material

    Knitter, R.; Reimann, J.; Risthaus, P.; Boccaccini, L.V.; Piazza, G.

    2004-01-01

    For the European Helium Cooled Pebble Bed (HCPB) blanket slightly overstoichiometric lithium orthosilicate pebbles (Li 4 SiO 4 +SiO 2 ) have been chosen as one optional breeder material. This material is developed in collaboration between Research Centre Karlsruhe (FZK) and the Schott Glas, Mainz. The lithium orthosilicate (OSi) pebbles are fabricated by the melting and spraying method in a semi-industrial scale facility. In the past, the not enriched pebbles were produced from a mixture of Li 4 SiO 4 and SiO 2 powders, but due to the fact that enriched Li 4 SiO 4 is not available on the market, highly enriched carbonate powder was used that finally resulted in nonsatisfying pebble characteristics. Enriched LiOH powder is commercially available, therefore, a new production route was pursued based on the following, simplified reaction: 4 LiOH + SiO 2 → Li 4 SiO 4 + 2 H 2 O. The melting process of LiOH and SiO 2 is less difficult to control than the melting of Li 2 CO 3 in spite of the decomposition of water. The pebbles produced from LiOH and SiO 2 are similar to those produced from Li 4 SiO 4 and SiO 2 . They exhibit a distinctly dendritic structure and show only a small amount of pores and cracks. In addition to the main constituent Li 4 SiO 4 , the high temperature phase Li 6 Si 2 O 7 was detected due to the quenching process and the excess of SiO 2 . This minor constituent, however, decomposes to Li 4 SiO 4 and Li 2 SiO 3 during annealing. In compressive crush load tests of single pebbles a crush load of about 9.5 N was measured for pebbles after drying at 300degC. The chemical analysis revealed a further advantage of the use of LiOH in the melting process. As LiOH is available in high-purity quality, the pebbles contain impurities to a lower degree than pebbles produced from Li 4 SiO 4 or Li 2 CO 3 . In order to obtain characteristic pebble bed data, first Uniaxial Compression Tests (UCTs) were performed at temperatures between ambient and at 850deg

  19. Analysis of waste coal from the enterprises of Kemerovo region as raw materials for production of ceramic materials

    Stolboushkin, A. Yu; Akst, D. V.; Fomina, O. A.; Ivanov, A. I.; Syromyasov, V. A.

    2017-09-01

    The analysis of waste coal from mining enterprises of Kemerovo region as raw materials for production of building ceramics is given. The results of studies of material, chemical and mineralogical compositions of waste coal from Abashevskaya processing plant (Novokuznetsk) are presented. It was established that the chemical composition of waste coal refers to aluminosilicate raw materials with a high content of alumina and coloring oxides, the residual carbon content in the wastes is 12-25 %. According to the granulometric composition the waste coal is basically a sandy-dusty fraction with a small amount of clay particles (1-3 %). Additional grinding of coal waste and the introduction of a clay additive in an amount of up to 30 % are recommended. The results of the study of the mineral composition of waste coal are presented. Clay minerals are represented in the descending order by hydromuscovite, montmorillonite and kaolinite, minerals-impurities consist of quartz, feldspar fine-dispersed carbonates. The results of the investigation of ceramic-technological properties of waste coal, which belong to the group of moderately plastic low-melting raw materials, are given. As a result of a comprehensive study it was been established that with chemical, granulometric and mineralogical compositions waste coal with the reduced residual carbon can be used in the production of ceramic bricks.

  20. Hook tool manufacture in New Caledonian crows: behavioural variation and the influence of raw materials.

    Klump, Barbara C; Sugasawa, Shoko; St Clair, James J H; Rutz, Christian

    2015-11-18

    New Caledonian crows use a range of foraging tools, and are the only non-human species known to craft hooks. Based on a small number of observations, their manufacture of hooked stick tools has previously been described as a complex, multi-stage process. Tool behaviour is shaped by genetic predispositions, individual and social learning, and/or ecological influences, but disentangling the relative contributions of these factors remains a major research challenge. The properties of raw materials are an obvious, but largely overlooked, source of variation in tool-manufacture behaviour. We conducted experiments with wild-caught New Caledonian crows, to assess variation in their hooked stick tool making, and to investigate how raw-material properties affect the manufacture process. In Experiment 1, we showed that New Caledonian crows' manufacture of hooked stick tools can be much more variable than previously thought (85 tools by 18 subjects), and can involve two newly-discovered behaviours: 'pulling' for detaching stems and bending of the tool shaft. Crows' tool manufactures varied significantly: in the number of different action types employed; in the time spent processing the hook and bending the tool shaft; and in the structure of processing sequences. In Experiment 2, we examined the interaction of crows with raw materials of different properties, using a novel paradigm that enabled us to determine subjects' rank-ordered preferences (42 tools by 7 subjects). Plant properties influenced: the order in which crows selected stems; whether a hooked tool was manufactured; the time required to release a basic tool; and, possibly, the release technique, the number of behavioural actions, and aspects of processing behaviour. Results from Experiment 2 suggested that at least part of the natural behavioural variation observed in Experiment 1 is due to the effect of raw-material properties. Our discovery of novel manufacture behaviours indicates a plausible scenario for the

  1. Preparation of High Purity, High Molecular-Weight Chitin from Ionic Liquids for Use as an Adsorbate for the Extraction of Uranium from Seawater

    Rogers, Robin [Univ. of Alabama, Tuscaloosa, AL (United States)

    2013-12-21

    Ensuring a domestic supply of uranium is a key issue facing the wider implementation of nuclear power. Uranium is mostly mined in Kazakhstan, Australia, and Canada, and there are few high-grade uranium reserves left worldwide. Therefore, one of the most appealing potential sources of uranium is the vast quantity dissolved in the oceans (estimated to be 4.4 billion tons worldwide). There have been research efforts centered on finding a means to extract uranium from seawater for decades, but so far none have resulted in an economically viable product, due in part to the fact that the materials that have been successfully demonstrated to date are too costly (in terms of money and energy) to produce on the necessary scale. Ionic Liquids (salts which melt below 100{degrees}C) can completely dissolve raw crustacean shells, leading to recovery of a high purity, high molecular weight chitin powder and to fibers and films which can be spun directly from the extract solution suggesting that continuous processing might be feasible. The work proposed here will utilize the unprecedented control this makes possible over the chitin fiber a) to prepare electrospun nanofibers of very high surface area and in specific architectures, b) to modify the fiber surfaces chemically with selective extractant capacity, and c) to demonstrate their utility in the direct extraction and recovery of uranium from seawater. This approach will 1) provide direct extraction of chitin from shellfish waste thus saving energy over the current industrial process for obtaining chitin; 2) allow continuous processing of nanofibers for very high surface area fibers in an economical operation; 3) provide a unique high molecular weight chitin not available from the current industrial process, leading to stronger, more durable fibers; and 4) allow easy chemical modification of the large surface areas of the fibers for appending uranyl selective functionality providing selectivity and ease of stripping. The

  2. Preparation of High Purity, High Molecular-Weight Chitin from Ionic Liquids for Use as an Adsorbate for the Extraction of Uranium from Seawater

    Rogers, Robin

    2013-01-01

    Ensuring a domestic supply of uranium is a key issue facing the wider implementation of nuclear power. Uranium is mostly mined in Kazakhstan, Australia, and Canada, and there are few high-grade uranium reserves left worldwide. Therefore, one of the most appealing potential sources of uranium is the vast quantity dissolved in the oceans (estimated to be 4.4 billion tons worldwide). There have been research efforts centered on finding a means to extract uranium from seawater for decades, but so far none have resulted in an economically viable product, due in part to the fact that the materials that have been successfully demonstrated to date are too costly (in terms of money and energy) to produce on the necessary scale. Ionic Liquids (salts which melt below 100 deg C) can completely dissolve raw crustacean shells, leading to recovery of a high purity, high molecular weight chitin powder and to fibers and films which can be spun directly from the extract solution suggesting that continuous processing might be feasible. The work proposed here will utilize the unprecedented control this makes possible over the chitin fiber a) to prepare electrospun nanofibers of very high surface area and in specific architectures, b) to modify the fiber surfaces chemically with selective extractant capacity, and c) to demonstrate their utility in the direct extraction and recovery of uranium from seawater. This approach will 1) provide direct extraction of chitin from shellfish waste thus saving energy over the current industrial process for obtaining chitin; 2) allow continuous processing of nanofibers for very high surface area fibers in an economical operation; 3) provide a unique high molecular weight chitin not available from the current industrial process, leading to stronger, more durable fibers; and 4) allow easy chemical modification of the large surface areas of the fibers for appending uranyl selective functionality providing selectivity and ease of stripping. The resulting

  3. New raw materials for radiation curable coatings: what are they, where they come from

    Rybny, C.B.; Trebellas, J.C.; Vona, J.A.

    1975-01-01

    The availability of reasonably priced coating systems which meet the criteria of low-energy cure and minimum effluent pollution is of critical concern to the coatings industry. To appreciate the problems associated with radiation curable coatings, those manufacturing and utilizing these materials should be aware of their raw material compositions and the starting products from which they are derived. The utility and economics of ultraviolet coatings are also of prime interest. These topics are discussed, with emphasis on the photocurable polymers and their cross-linking monomers as well as the economics of this new technology in relation to energy cost savings. 7 references

  4. Analysis of zirconia and alumina products and raw materials by X-ray fluorescence spectrometry

    Boix, A.; Draignaud, M.; Debras-Guedon, J.

    1975-01-01

    An X-ray fluorescence spectrometric method of analysis for various raw materials and materials based on zirconia, alumina and silica was developed. The measurements were made on beads made from the sample and a borax based flux, in the proportions 1:10. A repeatability test allowed the relative standard deviation to be estimated for the three main constituents: SiO 2 , Al 2 O 3 , ZrO 2 : it is at the level of 1%. The element analyzed are: Si, Al, Fe, Ti, Ca, Hf and Zr [fr

  5. Textile-reinforced concrete using composite binder based on new types of mineral raw materials

    Lesovik, V. S.; Glagolev, E. S.; Popov, D. Y.; Lesovik, G. A.; Ageeva, M. S.

    2018-03-01

    To determine the level of development of science, it is necessary to start with a particular stage in the development of society. At present, the purpose of building materials science is to create composites, which ensure safety of buildings and structures, including their protection against certain natural and man-made impacts. A new stage in construction materials science envisages the development of a technology for creating composites comfortable for a particular person. To implement this, a new paradigm for designing and synthesizing building materials with a new raw material base is needed. The optimization of the “human-material-habitat” system is a complex task, for the solution of which transdisciplinary approaches are required.

  6. Mechanochemical modification of the composition and structure of plant raw materials to control the combustion of alternative fuel

    Bychkov Aleksey

    2017-01-01

    Full Text Available The possibilities of mechanochemistry in processing of renewable lignocellulose raw material into solid kinds of biofuel are demonstrated in this work. A review of lignocellulose raw materials promising for our country is presented. These raw materials include wastes from agriculture and forestry, and the biomass of rapidly growing plants. The physicochemical properties of lignocellulose materials with different delignification degrees were modeled with the help of the artificial mixtures of plant raw material with purified cellulose and lignin. The data illustrating the effect of disperse state and lignin content on the reactivity of the material in subsequent combustion are presented. The tests at the combustion bench with the thermal power up to 5 MW allowed determining the optimal combustion parameters for the obtained biofuel in the autothermal mode.

  7. VERAM, for a sustainable and competitive future for EU Raw Materials

    Mobili, A.; Tittarelli, F.; Revel, G. M.; Wall, P.

    2018-03-01

    The project, VERAM “Vision and Roadmap for European Raw Materials”, aims to deliver a mapping of on-going initiatives on non-food, non-energy raw materials (including metals, industrial minerals, aggregates and wood) at European, Member State, and regional levels both from the Research and Innovation (R&I), industry, and policy perspectives. Moreover, based on a comprehensive gap analysis, VERAM will propose a common long term 2050 Vision and Roadmap in coordination and cooperation with all stakeholders across the value chain. For the first time, two European Technology Platforms (ETPs) together with their corresponding European Research Area Networks (ERA-NETs) are joining forces to develop a common roadmap.

  8. Beyond waste: new sustainable fillers from fly ashes stabilization, obtained by low cost raw materials

    N. Rodella

    2016-09-01

    Full Text Available A sustainable economy can be achieved only by assessing processes finalized to optimize the use of resources. Waste can be a relevant source of energy thanks to energy-from-waste processes. Concerns regarding the toxic fly ashes can be solved by transforming them into resource as recycled materials. The commitment to recycle is driven by the need to conserve natural resources, reduce imports of raw materials, save landfill space and reduce pollution. A new method to stabilize fly ash from Municipal Solid Waste Incinerator (MSWI at room temperature has been developed thanks to COSMOS-RICE LIFE+ project (www.cosmos-rice.csmt.eu. This process is based on a chemical reaction that occurs properly mixing three waste fly ashes with rice husk ash, an agricultural by-product. COSMOS inert can replace critical raw materials (i.e. silica, fluorspar, clays, bentonite, antimony and alumina as filler. Moreover the materials employed in the stabilization procedure may be not available in all areas. This paper investigates the possibility of substituting silica fume with corresponding condensed silica fume and to substitute flue-gas desulfurization (FGD residues with low-cost calcium hydroxide powder. The removal of coal fly ash was also considered. The results will be presented and a possible substitution of the materials to stabilize fly ash will be discussed.

  9. Physicochemical characterization of raw materials and co-products from the titanium dioxide industry

    Gazquez, M.J.; Bolivar, J.P.; Garcia-Tenorio, R.; Vaca, F.

    2009-01-01

    The present study was conducted to characterize several raw materials and co-products from the titanium dioxide industry in relation to their elemental composition (major, minor and trace elements), granulometry, mineralogy, microscopic morphology and physical composition. The main objective was to gain basic information for the future potential application of these co-products in fields such as agriculture, construction, civil engineering, etc. Microscopic studies were performed by applying scanning electron microscopy with X-ray microanalysis (SEM-XRMA) while the mineralogical compositions were analysed by means of the X-ray diffraction (XRD) technique. The concentrations of major elements such as Na, Al, Si, Ca, Ti, Fe, S and K were determined by X-ray fluorescence (XRF), while heavy metals and other trace elements were determined by ICP-MS. The physicochemical characterization of the raw materials used in the titanium dioxide industry, in addition to the characterization of the co-products generated, has enabled the evaluation of the degree of fractionation of different elements and compounds between the different co-products, as well as the control of the possible variations in the physicochemical composition of the raw materials throughout the time and the study of the influence of these variations in the characteristics of the obtained co-products. As a main conclusion of our study, it is possible to indicate that the levels of the pollutant elements associated to the co-products analysed were, in general, within safe limits and, therefore, they could potentially be used in composites as fertilizers or for building materials in road construction, etc. Nevertheless, for the specific application of each of these co-products in agriculture, construction and civil engineering, additional studies need to be performed to evaluate their appropriateness for the proposed application, together with specific studies on their health and environmental impact.

  10. Analytical methods to characterize heterogeneous raw material for thermal spray process: cored wire Inconel 625

    Lindner, T.; Bonebeau, S.; Drehmann, R.; Grund, T.; Pawlowski, L.; Lampke, T.

    2016-03-01

    In wire arc spraying, the raw material needs to exhibit sufficient formability and ductility in order to be processed. By using an electrically conductive, metallic sheath, it is also possible to handle non-conductive and/or brittle materials such as ceramics. In comparison to massive wire, a cored wire has a heterogeneous material distribution. Due to this fact and the complex thermodynamic processes during wire arc spraying, it is very difficult to predict the resulting chemical composition in the coating with sufficient accuracy. An Inconel 625 cored wire was used to investigate this issue. In a comparative study, the analytical results of the raw material were compared to arc sprayed coatings and droplets, which were remelted in an arc furnace under argon atmosphere. Energy-dispersive X-ray spectroscopy (EDX) and X-ray fluorescence (XRF) analysis were used to determine the chemical composition. The phase determination was performed by X-ray diffraction (XRD). The results were related to the manufacturer specifications and evaluated in respect to differences in the chemical composition. The comparison between the feedstock powder, the remelted droplets and the thermally sprayed coatings allows to evaluate the influence of the processing methods on the resulting chemical and phase composition.

  11. THE DEVELOPMENT OF PLANTS FOR THE PRODUCTION OF CONCENTRATED PASTES OF FRUIT AND VEGETABLE RAW MATERIALS

    G. O. Magomedov

    2015-01-01

    Full Text Available Summary. Developed a new system for producing concentrated semi-finished products in the form of pastes for the food industry. Currently, an important task of the food industry is the creation of new products with the aim of improving the structure of the range, saving scarce raw materials, as well as reduce sugar intake; development of product functionality and products with extended shelf life. The use of local non-traditional types of plant materials can contribute to solving existing problems. Fruit and vegetable pastes are a valuable food products which can be used as a semifinished product in the confectionery, bakery, food concentrates industry. Fruit and vegetable purees have a distinct structurally viscous or pseudo-plastic properties and concentration form a very viscous mass. Already in the beginning of the process of concentration, i.e. at a relatively low degree of evaporation that leads to a rapid increase in the viscosity of the concentrate mass and reduce evaporation. With increasing temperature is the burning mass, and also change its color and flavor. Therefore, for the concentration of fruit and vegetable purees, you must use equipment whose design takes into account the possible rheological and thermal problems. The analysis of literary data structures evaporators and studies, we developed a system for producing concentrated pastes of fruit and vegetable raw materials. Developed installation can increase the quality of the finished product due to the intensification of the process of concentration, to reduce material and energy resources, increase productivity.

  12. Discriminative illumination: per-pixel classification of raw materials based on optimal projections of spectral BRDF.

    Liu, Chao; Gu, Jinwei

    2014-01-01

    Classifying raw, unpainted materials--metal, plastic, ceramic, fabric, and so on--is an important yet challenging task for computer vision. Previous works measure subsets of surface spectral reflectance as features for classification. However, acquiring the full spectral reflectance is time consuming and error-prone. In this paper, we propose to use coded illumination to directly measure discriminative features for material classification. Optimal illumination patterns--which we call "discriminative illumination"--are learned from training samples, after projecting to which the spectral reflectance of different materials are maximally separated. This projection is automatically realized by the integration of incident light for surface reflection. While a single discriminative illumination is capable of linear, two-class classification, we show that multiple discriminative illuminations can be used for nonlinear and multiclass classification. We also show theoretically that the proposed method has higher signal-to-noise ratio than previous methods due to light multiplexing. Finally, we construct an LED-based multispectral dome and use the discriminative illumination method for classifying a variety of raw materials, including metal (aluminum, alloy, steel, stainless steel, brass, and copper), plastic, ceramic, fabric, and wood. Experimental results demonstrate its effectiveness.

  13. Occupational radiation protection in the mining and processing of raw materials

    2004-01-01

    The mining and processing of uranium ore, thorium ore and other raw materials containing natural radionuclides are carried out in a number of Member States. There is a clear need to update the guidance on the radiation protection of the workers involved, and this Safety Guide provides such updated guidance. Material from two previous publications has been adapted for inclusion in this Safety Guide. These previous publications - Radiation Monitoring in the Mining and Milling of Radioactive Ores (Safety Series No. 95) and Radiation Protection of Workers in the Mining and Milling of Radioactive Ores (Safety Series No. 26, hereby superseded) - dealt principally with activities involving uranium ore and thorium ore. Activity concentrations of naturally occurring radionuclides are elevated in other mineral deposits such as heavy mineral sands and phosphate rock. Furthermore, high radon levels may be found in mines, irrespective of the activity concentrations of natural radionuclides in the raw material being extracted. In recognition of these circumstances, this Safety Guide is intended to apply also to the mining and processing of any raw material for which radiation protection measures need to be considered. The IAEA Safety Fundamentals publication on Radiation Protection and the Safety of Radiation Sources presents the principles, concepts and objectives of protection and safety. Safety requirements based on the objectives and principles specified in these Safety Fundamentals, including requirements for the protection of workers exposed to ionizing radiation, are established in the International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources (the Basic Safety Standards or Bss). These requirements also reflect the recommendations of the International Commission on Radiological Protection (ICRP). Safety Guides provide recommendations on the basis of international experience on the fulfilment of the requirements

  14. The Influence Of Dead Layer Effect On The Characteristics Of The High Purity Germanium P-Type Detector

    Ngo Quang Huy

    2011-01-01

    The present work aims at reviewing the studies of the influence of dead layer effect on the characteristics of a high purity germanium (HPGe) p-type detector, obtained by the author and his colleagues in the recent years. The object for study was the HPGe GC1518 detector-based gamma spectrometer of the Center for Nuclear Techniques, Ho Chi Minh City. The studying problems were: The modeling of an HPGe detector-based gamma spectrometer with using the MCNP code; the method of determining the thickness of dead layer by experimental measurements of gamma spectra and the calculations using MCNP code; the influence of material parameters and dead layer on detector efficiency; the increase of dead layer thickness over the operating time of the GC1518 detector; the influence of dead layer thickness increase on the decrease of detector efficiency; the dead layer effect for the gamma spectra measured in the GC1518 detector. (author)

  15. Characterization of a high-purity germanium detector for small-animal SPECT.

    Johnson, Lindsay C; Campbell, Desmond L; Hull, Ethan L; Peterson, Todd E

    2011-09-21

    We present an initial evaluation of a mechanically cooled, high-purity germanium double-sided strip detector as a potential gamma camera for small-animal SPECT. It is 90 mm in diameter and 10 mm thick with two sets of 16 orthogonal strips that have a 4.5 mm width with a 5 mm pitch. We found an energy resolution of 0.96% at 140 keV, an intrinsic efficiency of 43.3% at 122 keV and a FWHM spatial resolution of approximately 1.5 mm. We demonstrated depth-of-interaction estimation capability through comparison of pinhole acquisitions with a point source on and off axes. Finally, a flood-corrected flood image exhibited a strip-level uniformity of less than 1%. This high-purity germanium offers many desirable properties for small-animal SPECT.

  16. Rare earth impurities in high purity lanthanum oxide determined by neutron activation analysis

    Nguyen Van Suc; Desai, H.B.; Parthasarathy, R.; Gangadharan, S.

    1992-01-01

    Individual rare earth impurities in high purity La 2 O 3 (≥99.9%) have been determined by NAA after pre-separation of the matrix (La). The separation is carried out on an anion exchanger (Dowex 1x8) using different mixtures of methanol/nitric acid as eluants. The rare earth elements from Dy to Lu are eluted quantitatively using a 10% 1M HNO 3 - 90% methanol mixture, while the light rare earths from Ce to Gd are eluted quantitatively using a 10% 0.05M HNO 3 - 90% methanol mixture. La, which is retained on the column, is eluted using 0.1M HNO 3 . The recoveries of the various rare earth elements have been checked using radiotracers and also by spiking the sample with known amount of elements, and the recoveries are found to be quantitative. Results obtained on a typical high purity lanthanum oxide are reported here. (author) 5 refs.; 1 fig

  17. Improved procedure for high purity gaseous peroxyacyl nitrate production: use of heavy lipid solvents

    Gaffney, J S; Fajer, R; Senum, G I

    1984-01-01

    An improved procedure is described for the production of peroxyacyl nitrates (PAN's) in the gas phase. The method of Nielsen et al. (1982) has been modified to yield PAN's of high purity with no further chromatographic purification required. Extraction of PAN's from the nitration of the peracids is accomplished by use of a heavy lipid solvent (n-tridecane). This solvent's low vapor pressure allows the simple separation and preparation of high purity gaseous PAN's (>98%) as determined by Fourier transform infrared spectroscopy (FTIR). Using this method infrared integrated band strengths are reported for peroxyacetyl nitrate (PAN) perdeutero-peroxyacetyl nitrate (PAN-D/sub 3/) and peroxyproprionyl nitrate (PPN). The method allows facile production of large amounts of gaseous PAN's for smog chamber and laboratory studies, toxicological and health effects research, as well as for calibration of PAN analyses.

  18. Fabrication of novel cryomill for synthesis of high purity metallic nanoparticles

    Kumar, Nirmal; Biswas, Krishanu

    2015-08-01

    The successful preparation of free standing metal nanoparticles with high purity in bulk quantity is the pre-requisite for any potential application. This is possible by using ball milling at cryogenic temperature. However, the most of ball mills available in the market do not allow preparing high purity metal nanoparticles by this route. In addition, it is not possible to carry out in situ measurements of process parameters as well as diagnostic of the process. In the present investigation, we present a detailed study on the fabrication of a cryomill, which is capable of avoiding contaminations in the product. It also provides in situ measurements and diagnostic of the low temperature milling process. Online monitoring of the milling temperature and observation of ball motion are the important aspects in the newly designed mill. The nanoparticles prepared using this fabricated mill have been found to be free standing and also free from contaminations.

  19. Comparison of Deformation in High-Purity Single/Large Grain and Polycrystalline Niobium Superconducting Cavities

    Ganapati Rao Myneni; Peter Kneisel

    2005-01-01

    The current approach for the fabrication of superconducting radio frequency (SRF) cavities is to roll and deep draw sheets of polycrystalline high-purity niobium. Recently, a new technique was developed at Jefferson Laboratory that enables the fabrication of single-crystal high-purity Nb SRF cavities. To better understand the differences between SRF cavities fabricated out of fine-grained polycrystalline sheet in the standard manner and single crystal cavities fabricated by the new technique, two half-cells were produced according to the two different procedures and compared using a variety of analytical techniques including optical microscopy, scanning laser confocal microscopy, profilometry, and X-ray diffraction. Crystallographic orientations, texture, and residual stresses were determined in the samples before and after forming and this poster presents the results of this ongoing study

  20. Some aspects of ICP-AES analysis of high purity rare earths

    Murty, P.S.; Biswas, S.S.

    1991-01-01

    Inductively coupled plasma atomic emission spectrometry (ICP-AES) is a technique capable of giving high sensitivity in trace elemental analysis. While the technique possesses high sensitivity, it lacks high selectivity. Selectivity is important where substances emitting complex spectra are to be analysed for trace elements. Rare earths emit highly complex spectra in a plasma source and the determination of adjacent rare earths in a high purity rare earth matrix, with high sensitivity, is not possible due to the inadequate selectivity of ICP-AES. One approach that has yielded reasonably good spectral selectivity in the high purity rare earth analysis by ICP-AES is by employing a combination of wavelength modulation techniques and high resolution echelle grating. However, it was found that by using a high resolution monochromator senstitivities either comparable to or better than those reported by the wavelength modulation technique could be obtained. (author). 2 refs., 2 figs., 2 tabs

  1. Characterization of high-purity niobium structures fabricated using the electron beam melting process

    Terrazas Najera, Cesar Adrian

    Additive Manufacturing (AM) refers to the varied set of technologies utilized for the fabrication of complex 3D components from digital data in a layer-by-layer fashion. The use of these technologies promises to revolutionize the manufacturing industry. The electron beam melting (EBM) process has been utilized for the fabrication of fully dense near-net-shape components from various metallic materials. This process, catalogued as a powder bed fusion technology, consists of the deposition of thin layers (50 - 120microm) of metallic powder particles which are fused by the use of a high energy electron beam and has been commercialized by Swedish company Arcam AB. Superconducting radio frequency (SRF) cavities are key components that are used in linear accelerators and other light sources for studies of elemental physics. Currently, cavity fabrication is done by employing different forming processes including deep-drawing and spinning. In both of the latter techniques, a feedstock high-purity niobium sheet with a thickness ranging from 3-4 mm is mechanically deformed and shaped into the desired geometry. In this manner, half cavities are formed that are later joined by electron beam welding (EBW). The welding step causes variability in the shape of the cavity and can also introduce impurities at the surface of the weld interface. The processing route and the purity of niobium are also of utmost importance since the presence of impurities such as inclusions or defects can be detrimental for the SRF properties of cavities. The focus of this research was the use of the EBM process in the manufacture of high purity niobium parts with potential SRF applications. Reactor grade niobium was plasma atomized and used as the precursor material for fabrication using EBM. An Arcam A2 system was utilized for the fabrication. The system had all internal components of the fabrication chamber replaced and was cleaned to prevent contamination of niobium powder. A mini-vat, developed at

  2. Aluminium. II - A review of deformation properties of high purity aluminium and dilute aluminium alloys.

    Reed, R. P.

    1972-01-01

    The elastic and plastic deformation behavior of high-purity aluminum and of dilute aluminum alloys is reviewed. Reliable property data, including elastic moduli, elastic coefficients, tensile, creep, fatigue, hardness, and impact are presented. Single crystal tensile results are discussed. Rather comprehensive reference lists, containing publications of the past 20 years, are included for each of the above categories. Defect structures and mechanisms responsible for mechanical behavior are presented. Strengthening techniques (alloys, cold work, irradiation, quenching, composites) and recovery are briefly reviewed.

  3. Perfomance of a high purity germanium multi-detector telescope for long range particles

    Riepe, G.; Protic, D.; Suekoesd, C.; Didelez, J.P.; Frascaria, N.; Gerlic, E.; Hourani, E.; Morlet, M.

    1980-01-01

    A telescope of stacked high purity germanium detectors designed for long range charged particles was tested using medium energy protons. Particle identification and the rejection of the low energy tail could be accomplished on-line allowing the measurement of complex spectra. The efficiency of the detector stack for protons was measured up to 156 MeV incoming energy. The various factors affecting the energy resolution are discussed and their estimated contributions are compared with the experimental results

  4. The element analysis of high purity beryllium by method of laser mass-spectrometry

    Virich, V.D.; Kisel', O.V.; Kovtun, K.V.; Pugachev, N.S.; Yakobson, L.A.

    2003-01-01

    The operation is devoted to examination of a possibility of the analysis of element composition pure and high purity model of a beryllium is model by a method of laser mass spectrometry. The advantages of a method in a part of finding of a small amount of admixtures in comparison with other modes of the analysis are exhibited. The possibility of quantitative definition of a content in beryllium samples of gas-making admixtures-C,N,O surveyed

  5. A Study of the Surface Quality of High Purity Copper after Heat Treatment

    Aicheler, M; Atieh, S; Calatroni, S; Riddone, G; Lebet, S; Samoshkin, A

    2011-01-01

    Themanufacturing flow of accelerating structures for the compact linear collider, based on diamond-machined high purity copper components, include several thermal cycles (diffusion bonding, brazing of cooling circuits, baking in vacuum, etc.). The high temperature cycles may be carried out following different schedules and environments (vacuum, reducing hydrogen atmosphere, argon, etc.) and develop peculiar surface topographies which have been the object of extended observations. This study presents and discusses the results of scanning electron microscopy (SEM) and optical microscopy investigations.

  6. Operation of a high-purity silicon diode alpha particle detector at 1. 4 K

    Martoff, C.J.; Kaczanowicz, E. (Temple Univ., Philadelphia, PA (USA)); Neuhauser, B.J.; Lopez, E.; Zhang, Y. (San Francisco State Univ., CA (USA)); Ziemba, F.P. (Quantrad Corp. (USA))

    1991-03-01

    Detection of alpha particles at temperatures as low as 1.4 K was demonstrated using a specially fabricated Si diode. The diode was 475 mm{sup 2} by 0.280 mm thick, fabricated from high-purity silicon with degenerately doped contacts. This is an important step toward development of dual-mode (ionization plus phonon) silicon detectors for low energy radiation. (orig.).

  7. Charge collection performance of a segmented planar high-purity germanium detector

    Cooper, R.J. [Department of Physics, The University of Liverpool, Oliver Lodge Laboratory, Liverpool Merseyside L69 7ZE (United Kingdom)], E-mail: R.Cooper@liverpool.ac.uk; Boston, A.J.; Boston, H.C.; Cresswell, J.R.; Grint, A.N.; Harkness, L.J.; Nolan, P.J.; Oxley, D.C.; Scraggs, D.P. [Department of Physics, The University of Liverpool, Oliver Lodge Laboratory, Liverpool Merseyside L69 7ZE (United Kingdom); Lazarus, I.; Simpson, J. [STFC Daresbury Laboratory, Warrington, Cheshire WA4 4AD (United Kingdom); Dobson, J. [Rosemere Cancer Centre, Royal Preston Hospital, Preston PR2 9HT (United Kingdom)

    2008-10-01

    High-precision scans of a segmented planar high-purity germanium (HPGe) detector have been performed with a range of finely collimated gamma ray beams allowing the response as a function of gamma ray interaction position to be quantified. This has allowed the development of parametric pulse shape analysis (PSA) techniques and algorithms for the correction of imperfections in performance. In this paper we report on the performance of this detector, designed for use in a positron emission tomography (PET) development system.

  8. High-purity Cu nanocrystal synthesis by a dynamic decomposition method

    Jian, Xian; Cao, Yu; Chen, Guozhang; Wang, Chao; Tang, Hui; Yin, Liangjun; Luan, Chunhong; Liang, Yinglin; Jiang, Jing; Wu, Sixin; Zeng, Qing; Wang, Fei; Zhang, Chengui

    2014-01-01

    Cu nanocrystals are applied extensively in several fields, particularly in the microelectron, sensor, and catalysis. The catalytic behavior of Cu nanocrystals depends mainly on the structure and particle size. In this work, formation of high-purity Cu nanocrystals is studied using a common chemical vapor deposition precursor of cupric tartrate. This process is investigated through a combined experimental and computational approach. The decomposition kinetics is researched via differential sca...

  9. Analysis of the strain-aging phenomena in high purity niobium: competition between hardening and recovery

    Andreone, C.; Cizeron, G.; Larere, A.

    1981-01-01

    The strain-aging phenomena in high purity niobium were studied using tensile tests. Four parameters were considered which characterize the yield point, the permanent hardening, the recovery and the apparent yield stress. Five successive steps can be distinguished from the changes in these parameters with changes in the aging temperature. The detailed analysis of the phenomena involved concerns mainly the locking of dislocations by first- and second-type segregations and the opposite effect of reorganization of the dislocation network. (Auth.)

  10. Activation analysis of high purity metals and application to study on physical properties

    Ueda, Yoshitake; Hashimoto, Eiji; Matsushita, Rokuji.

    1994-01-01

    In order to determine the true characteristics of matters, the utmost reduction of impurities is indispensable. By the heightening of the purity of aluminum, that of 99.9999% purity has been obtained, but efforts have been exerted to further heighten the purity. For the purpose, it is important to know the behavior of trace impurities during refining, and the quantitative research by neutron activation analysis for various impurities has been carried out. The research on the electron condition of trace impurity atoms in refined aluminum is also important. The band refining of high purity aluminum is explained. By repeating the refining 10 times, the sample of RRR exceeding 30000 was obtained. The impurities contributing to the resistivity are Sc, Ti, V and Cr. Based on the results, the heightening of aluminum purity was attempted by devising the new procedure. As for the electric properties of solute elements in high purity metals, those of transition elements and rare earth elements in aluminum are reported. As the result of measuring the remaining resistance, the sample having the RRR exceeding 45000 after the correction for size effect was done has been obtained. At present, the efforts toward further high purity are continued. (K.I.)

  11. Corrosion behavior of high purity Fe-Cr-Ni alloys in trans-passive condition

    Mayuzumi, Masami; Ohta, Jyoji; Kako, Kenji

    1998-01-01

    The corrosion behavior of high-purity (99.99%) Fe-Cr-Ni alloys was investigated in 13 N nitric acid with/without Ce 4+ ions to clarify the effect of impurities on the trans-passive corrosion of stainless steel. The following results were obtained. (1) Almost no intergranular corrosion was observed in the high-purity alloys, although the corrosion rate of the matrix region was nearly the same as that of a commercial stainless steel with the same Cr and Ni content. (2) Due to the improved intergranular corrosion resistance, the effect of the purification became significant in the corrosion condition with the grain-separation being predominant. (3) The high-purity alloys showed higher susceptivility to intergranular corrosion with aging treatment between 873 K and 1073 K. Although the sulfuric acid/copper sulfate test suggested the formation of Cr-depleted zones, a grain boundary micro-analysis using a FETEM with an EDX did not reveal any change in Cr content or impurity segregain along the grain boundaries. The mechanism of corrosion enhancement resulting from the aging treatment remains nuclear. (author)

  12. Towards a dynamic assessment of raw materials criticality: linking agent-based demand--with material flow supply modelling approaches.

    Knoeri, Christof; Wäger, Patrick A; Stamp, Anna; Althaus, Hans-Joerg; Weil, Marcel

    2013-09-01

    Emerging technologies such as information and communication-, photovoltaic- or battery technologies are expected to increase significantly the demand for scarce metals in the near future. The recently developed methods to evaluate the criticality of mineral raw materials typically provide a 'snapshot' of the criticality of a certain material at one point in time by using static indicators both for supply risk and for the impacts of supply restrictions. While allowing for insights into the mechanisms behind the criticality of raw materials, these methods cannot account for dynamic changes in products and/or activities over time. In this paper we propose a conceptual framework intended to overcome these limitations by including the dynamic interactions between different possible demand and supply configurations. The framework integrates an agent-based behaviour model, where demand emerges from individual agent decisions and interaction, into a dynamic material flow model, representing the materials' stocks and flows. Within the framework, the environmental implications of substitution decisions are evaluated by applying life-cycle assessment methodology. The approach makes a first step towards a dynamic criticality assessment and will enhance the understanding of industrial substitution decisions and environmental implications related to critical metals. We discuss the potential and limitation of such an approach in contrast to state-of-the-art methods and how it might lead to criticality assessments tailored to the specific circumstances of single industrial sectors or individual companies. Copyright © 2013 Elsevier B.V. All rights reserved.

  13. Obtention of high purity silica from the flotation waste of itabiritic ore

    Martins, Polyana Fabricia Fernandes

    2016-01-01

    Banded iron formations are exploited as iron mineral in 'Quadrilatero Ferrifero' of Minas Gerais (MG) State, Brazil. About half of the amount of extracted material becomes tailings, which are stored in tailing dams or used for filling mining pits. Tens of thousands of tons are generated daily in operating mines in this region, causing concern about the environmental liabilities, and costs to manage the tailing dams. Miners are committed to finding uses for these wastes in other productive chains. This thesis aimed to obtain high purity silica from the flotation tailings of banded iron formations using classical techniques for ore processing, such as particle size classification and magnetic separation, followed by hydrometallurgical leaching, also alkaline fusion and chemical precipitation. The tailings samples was collected in the tailings dam of Peak Mine operated by Vale A.S., in Itabirito – MG. This sample had initially 33.4% by weight SiO 2 , 57.4% wt Fe 2 O 3 and 8.31% wt Al 2 O 3 . After desliming for disposal of the fine particles (-37μm) the composition was 68.0% SiO 2 , 31.4% Fe 2 O 3 and 0.50% Al 2 O 3 . After magnetic separation, the composition was 93.8% SiO 2 , 1.16% Fe 2 O 3 and 3.80% Al 2 O 3 . After acid leaching l or digestion to remove impurities, it was possible to obtain silica with 98% purity. The fusion with sodium hydroxide, followed by alkaline leaching of sodium silicate and silica precipitation gave purities of about 99.5%. Values even higher may be possible with optimization of the parameters of alkaline fusion or by repeating the process from the product with purity of 99.5%. The iron oxide content and the aluminum main contaminants were 0.01% and 0.07%, respectively. Amorphous silica was obtained with high specific surface (322 m 2 /g) and particle size less than 200 nm. Depending on the application, a control should be made for the impurities, such as phosphorus, potassium and boron. (author)

  14. Diffusion bonding and brazing of high purity copper for linear collider accelerator structures

    J. W. Elmer

    2001-05-01

    Full Text Available Diffusion bonding and brazing of high purity copper were investigated to develop procedures for joining precision machined copper components for the Next Linear Collider (NLC. Diffusion bonds were made over a range of temperatures from 400 °C to 1000 °C, under two different loading conditions [3.45 kPa (0.5 psi and 3.45 MPa (500 psi], and on two different diamond machined surface finishes. Brazes were made using pure silver, pure gold, and gold-nickel alloys, and different heating rates produced by both radiation and induction heating. Braze materials were applied by both physical vapor deposition (PVD and conventional braze alloy shims. Results of the diffusion bonding experiments showed that bond strengths very near that of the copper base metal could be made at bonding temperatures of 700 °C or higher at 3.45 MPa bonding pressure. At lower temperatures, only partial strength diffusion bonds could be made. At low bonding pressures (3.45 kPa, full strength bonds were made at temperatures of 800 °C and higher, while no bonding (zero strength was observed at temperatures of 700 °C and lower. Observations of the fracture surfaces of the diffusion bonded samples showed the effects of surface finish on the bonding mechanism. These observations clearly indicate that bonding began by point asperity contact, and flatter surfaces resulted in a higher percentage of bonded area under similar bonding conditions. Results of the brazing experiments indicated that pure silver worked very well for brazing under both conventional and high heating rate scenarios. Similarly, pure silver brazed well for both the PVD layers and the braze alloy shims. The gold and gold-containing brazes had problems, mainly due to the high diffusivity of gold in copper. These problems led to the necessity of overdriving the temperature to ensure melting, the presence of porosity in the joint, and very wide braze joints. Based on the overall findings of this study, a two

  15. Lithic assemblages of Azokh Cave (Nagorno Karabagh, Lesser Caucasus: Raw materials, technology and regional context

    Lena Asryan

    2014-03-01

    Full Text Available Azokh Cave is a Middle Pleistocene to Holocene site located in Nagorno Karabagh (Lesser Caucasus. The main entrance, Azokh 1, is a large cave that has two geological sequences (lower and upper with nine geo-archaeological units of which only the upper ones (Units I to V have a significant archaeological record.  The faunal remains and lithic artefacts in these units indicate aspects of human occupation, and exploitation of, and association with animals.     The lithic artefacts presented here were recovered from Units V, III and II during the 2002 – 2009 excavation seasons. The available chronological data indicates an age between 293 – 100 Ka for these units. The operational chain is incomplete and artefacts found in the cave are primarily end-products dominated by flake-tools. The assemblage of Unit V is composed primarily of simple, unretouched flakes with a minimal presence of retouched flakes and cores. The Unit II lithic assemblage includes a substantial Levallois component, although with fewer cores and retouched flakes. There are very few flake tools in Unit III. While it is still difficult to assign the Unit V assemblage to a techno-typological group or complex (i.e. Acheulean, Mousterian or other local techno-complexes such as the Kudarian, the Unit II assemblage is clearly associated with Mode 3 or the Mousterian techno-complex.Different local and non-local raw materials were exploited in all units for the production of lithic artefacts, although the range of raw materials is more varied in Unit II. Local chert, flint and basalt were used most commonly, probably due to their easy accessibility. Limestone, jasper and sandstone, from local and non-local sources, are present in small quantities in Units V and II. Obsidian is the only raw material that possibly originates from more distant sources. Flint and chert appear to have been preferentially exploited for flake tool production in all units, but the toolmakers show a

  16. Energies and raw materials. Letter n.28; Energies matieres premieres. Lettre n. 28

    NONE

    2007-01-15

    This letter of the DGEMP (General Direction of the Energy and the Raw Materials) deals with the following four main topics: the main recommendations of the final report of the working Group ''Factor 4'' concerning the energy policy; the energy conservation certificates as a tool of the energy control with their implication in the residential and ternary sector; the increase of the solar water heaters and heat pumps sales thanks to the tax credits; the California example facing the climatic change and the energy policy. (A.L.B.)

  17. Utilization of silicifed Tertiary wood as raw material for the natural stone industry. [German Democratic Republic

    Bellmann, H J; Schuettler, J; Jakisch, E

    1981-11-01

    This paper discusses the occurrence of silicified tree trunks and stumps in the Boehlen brown coal field. The trees, mainly Taxodium and Sequoia 25 million years old, are located within the top brown coal seam of the deposit and present a major obstacle to excavator operation, together with other forms of so-called 'brown coal quartzite'. The quartz of the silicified trees occurs as opal, cryptocrystalline quartz and low temperature quartz. The separate removal and disposal of this wood as well as efforts made to use selected wood as raw material are briefly summarized. Various products for interior house decoration have been manufactured from the wood. (4 refs.)

  18. Utilisation of biological and secondary raw materials IX. Recycling - conversion to energy

    Wiemer, Klaus; Kern, Michael; Raussen, Thomas

    2014-01-01

    The book on the utilization of biological and secondary raw materials covers the following issues: Perspectives of the circular flow and resource economy, waste avoidance, closed substance cycle waste management law and biowaste assessment, economic evaluation and usage alternatives for biogas, consequences of the 4th BlmschV, the BioAbfV and the DueV for the biowaste treatment, alternative techniques of the Biowaste collection, alternative models of the recyclable substance assessment, future of the packaging and recyclable substance utilization, ElectroG and E-scrape recycling, innovative concepts for the municipal waste management, future of the MBA, MVA and EBS management.

  19. Analysis of forecasting and inventory control of raw material supplies in PT INDAC INT’L

    Lesmana, E.; Subartini, B.; Riaman; Jabar, D. A.

    2018-03-01

    This study discusses the data forecasting sales of carbon electrodes at PT. INDAC INT L uses winters and double moving average methods, while for predicting the amount of inventory and cost required in ordering raw material of carbon electrode next period using Economic Order Quantity (EOQ) model. The result of error analysis shows that winters method for next period gives result of MAE, MSE, and MAPE, the winters method is a better forecasting method for forecasting sales of carbon electrode products. So that PT. INDAC INT L is advised to provide products that will be sold following the sales amount by the winters method.

  20. Connections between borehole geophysical parameters of the quality of cement raw materials

    Szabo, L.; Illes, A.

    1978-01-01

    The raw materials for the cement industry are prospected - according to the recommendations of national authorities - by geophysical methods, too. These include not the determination of the deposit boundary, but also an estimation of the quality of limestone and clay from the point of cement manufacture. No forerunners of such tests exist, so new methods were elaborated. After 12 years of site tests it was found that the correlation between laboratory quality tests and certain geophysical parameters of clay deposits is fair but less close in case of limestone deposits. (author)

  1. The application of isotopic dating methods for prospection and exploration of nuclear raw material

    Komlev, L.V.; Anderson, E.B.

    1977-01-01

    Among the geological and geochemical methods for prospecting and searching the nuclear raw material, the isotope-dating methods determine the most important search criterion - the time of the ore-forming. The elaboration and use of these methods in uranium-ore regions reveal a series of geochemical epochs of uranium and thorium accumulation connected naturally with the history of geological evolution of the earth crust. The isotope-dating methods enable with confidence to establish the stages of tectono-magmatic activity resulting in the redistribution and the local concentration of uranium. The wide use of isotopic methods is a necessary condition for reasonable trends of the modern geological exploration [ru

  2. Mechanical Properties and Microstructure of Fast – Fired Clinker Tiles Based on Wierzbka I Raw Material

    Gajek M.; Rapacz-Kmita A.; Dudek M.; Partyka J.

    2016-01-01

    The article presents results of research on microstructural and mechanical properties of floor tiles clinker manufactured on the basis of Wierzbka I raw material, which is part of the deposit Wierzbka, near Suchedniów. Wierzbka I clay was added in various volume fractions to the standard tile compositions used in industrial practice. The samples were pressed in a range of from 21 MPa to 42 MPa and fired in the laboratory furnace at 1130°C to 1190°C. Selected compositions were pressed at 28 MP...

  3. Determination of optimum mixing time for raw materials with the tracer method in the glass industry

    Gallyas, M; Gemesi, J; Kurinka, J

    1983-02-01

    The authors explain how the optimum mixing time for the raw materials for glass manufacture can be determined with the aid of the radioactive tracer method. Basing themselves on measurements, they indicate the change in the degree of mixing of the individual components (soda (Na-24), sodium sulphate, coke (La-140) and bone meal (P-32) as a function of mixing time. The optimum degree of mixing and mixing time for dry and for wet mixing are determined. Finally, data for determining the permissible storage time of the mixture are given.

  4. Whey as a raw material for the production of functional beverages

    Bulatović Maja Lj.

    2012-01-01

    Full Text Available One of the least utilized by-products of food industry, despite the great potential that is described, is the whey, which is obtained as a by-product of the technological process production of cheese and casein. The excess whey, which occurs in this process in very high yields, with failure to processing is becoming a very big polluter, what is completely at odds with the potential that such materials possess. On the other hand, the modern tempo and way of life, and increasingly polluted environmental also, impose the need to produce food products that would help the human body in the fight against harmful agents which are exposed to daily. One of the more effective solution is the production of fermented functional beverages based on whey, which achieved this intention in the most natural and most comfortable way. Considering the rather untapped potential of whey as a raw material and growing food shortages in the world market, the aim of this study was to analyze the possibilities of production of functional beverages based on whey, with satisfactory sensory characteristics, in order to demonstrate the attractiveness of whey as raw material in the food industry. This paper presents an overview of the wide possibilities for the use of whey with a special emphasis on its attractiveness and the necessity of its utilizing.

  5. Mineralogical and technology characterization of raw materials of clay used for ceramic blocks fabrication

    Campos, N.Q.; Tapajos, N.S.

    2012-01-01

    In the state of Para, the red ceramic industry has several segments highly generators of jobs and a strong social appeal. With so many companies focused on this productive sector emerge, but many without any administration quality. Therefore, this study focused the technological and mineralogical characterization of the raw material used in the manufacture of ceramic blocks, by Ceramica Vermelha Company, located in the district of Inhangapi-PA. The raw material was obtained by the techniques of X-ray diffraction (XRD) to determine the present crystalline phases through an accurate and efficient procedure, where it was possible to identify the peaks relating to montmorillonite, illite and kaolinite clay in the sample, and kaolinite and quartz in the sample laterite. Another important result was the absorption of water, with average satisfactory according to the standards. According to a sieve analysis, the laterite the sand fraction showed a greater extent compared to the other, while the clay silt exceeding 80% was found to be too plastic material. The resistance to compression, the results were below the required by the standard, suggesting more accurate test methods. (author)

  6. Potential of Electronic Plastic Waste as a Source of Raw Material and Energy Recovery

    Norazli Othman; Nor Ezlin Ahmad Basri; Lariyah Mohd Sidek

    2009-01-01

    Nowadays, the production of electronic equipment is one of the fastest growing industrial activities in this world. The increase use of plastic in this sector resulted in an increase of electronic plastic waste. Basically, electronic plastic material contains various chemical elements which act as a flame retardant when electronic equipment is operated. In general, the concept of recycling electronic plastic waste should be considered in order to protect the environment. For this purpose, research has been conducted to different resins of electronic plastic waste to identify the potential of electronic plastic waste as a source of raw material and energy recovery. This study was divided into two part for example determination of physical and chemical characteristics of plastic resins and calculation of heating value for plastic resins based on Dulong formula. Results of this research show that the average calorific value of electronic waste is 30,872.42 kJ/ kg (7,375 kcal/ kg). The emission factor analysis showed that the concentration of emission value that might occur during waste management activities is below the standard set by the Environment Quality Act 1974. Basically, this research shows that electronic plastic waste has the potential to become the source of raw material and energy recovery. (author)

  7. Calcium flouride (CaF2) from oyster shell as a raw material for thermoluminescence dosimeter

    Coloma, Lyra C.; Fanuga, Lyn N.; Ocreto, Cherries Ann; Rodriguez, Richita

    2006-03-01

    This study aims to develop a thermoluminescence dosimeter raw material made of calcium fluoride from locally available seashells that is suitable for personal radiation monitoring. Oyster shells were collected and grounded as powder samples and analyzed for calcium fluoride (CaF 2 ) content using XRF and XRD testing. Samples include pure CaF 2 , pure oyster shell, and oyster shells treated with acid. Based from the XRF results, natural oyster shell (w/ and w/o HNO 3 ) had high percentage of calcium about 49.64% and 47.45%, next to the pure calcium fluoride of 51.08%. X-ray diffractrogram shows that oyster sample had the nearest desired structure of CaF 2 compared with two seashells relative to the pure CaF 2 as standard materials. Results show that all of the natural oyster samples displayed TL emission glow curves at the temperature range 200-300 o C. It was also found that pure oyster sample has better TL response as compared to the treated ones. The researchers concluded that the calcium fluoride from oyster shells (without acid and heated) is a potentially good low-cost TLD raw material and may be used as an alternative for the much more expensive LiF dosimeters. (Authors)

  8. OPTICAL-ELECTRONIC SYSTEM FOR EXPRESS ANALYSIS OF ORE DRESSABILITY FOR MINERAL RAW MATERIALS BY OPTICAL METHOD

    A. A. Alekhin

    2013-05-01

    Full Text Available The article deals with creation results of experimental prototype of optical-electronic complex, designed to assess ore dressability of mineral raw materials by optical sorting method.

  9. Cutin from agro-waste as a raw material for the production of bioplastics.

    Heredia-Guerrero, José A; Heredia, Antonio; Domínguez, Eva; Cingolani, Roberto; Bayer, Ilker S; Athanassiou, Athanassia; Benítez, José J

    2017-11-09

    Cutin is the main component of plant cuticles constituting the framework that supports the rest of the cuticle components. This biopolymer is composed of esterified bi- and trifunctional fatty acids. Despite its ubiquity in terrestrial plants, it has been underutilized as raw material due to its insolubility and lack of melting point. However, in recent years, a few technologies have been developed to obtain cutin monomers from several agro-wastes at an industrial scale. This review is focused on the description of cutin properties, biodegradability, chemical composition, processability, abundance, and the state of art of the fabrication of cutin-based materials in order to evaluate whether this biopolymer can be considered a source for the production of renewable materials. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  10. 4.2. The kinetics of nitric acid decomposition of calcined borosilicate raw material of Ak-Arkhar Deposit

    Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

    2015-01-01

    Present article is devoted to kinetics of nitric acid decomposition of calcined borosilicate raw material of Ak-Arkhar Deposit. The dependence of nitric acid decomposition of calcined boric raw material for extraction of boron oxide on temperature (20-100 deg C) and process duration (15-60 minutes) was defined. It was defined that at temperature increasing the extraction rate of boron oxide increases from 20.8 to 78.6%.

  11. Analysis of Cement as Raw Material Inventory on Ready Mix Production Unit at PT. Perdana Beton in Samarinda

    Wahyuni, Novita Eka

    2014-01-01

    This study aims to identify and analyze the optimal amount of cement supplies in PT. Perdana Beton In Samarinda. Formulation of the problem in this study is whether the supply of cement as raw material for Ready Mix at PT. Perdana Beton In Samarinda already minimizing the cost of inventory cement. The hypothesis in this study is: '' Allegedly cement as raw material supplies ready mix at PT. Perdana Beton In Samarinda not provide minimum inventory costs'. Basic...

  12. Anthropogenic materials and products containing natural radionuclides. Pt. 1a. Radiation properties of raw materials and waste materials. A literature study

    Reichelt, A.; Roehrer, J.; Lehmann, K.H.

    1995-12-01

    Cased on the literature study, the publication presents relevant data on raw materials and wastes containing natural radionuclides. The study is part 1a of the project on ''Anthropogenic materials and waste materials containing natural radionuclides''. Part 1 of the project gives data and information on about 100 different materials and wastes or products for household or industrial applications which contain significant amounts of natural radioactivity. In addition, part 1 presents for some of these materials information on their applications, consumption, radioactivity and resulting radiation doses. The raw materials and waste materials on the list in part 1 are characterised in this 1a report. Wherever appropriate, two or more materials are dealt with in one chapter, as e.g. felspar and felspar sands (pegmatite), talcum, and soapstone. The wastes are dealt with in the chapters discussing the relevant raw materials. The information given is as derived from the literature and does not include comments or evaluation by the authors of this report. Whenever the literature study did not yield information on radiological aspects of a material on the list, an appropriate notice is given. (Orig./DG) [de

  13. Investigation and analysis on ITER in-vessel coils’ raw-materials

    Jin, Huan; Wu, Yu; Long, Feng; Yu, Min; Han, Qiyang; Liu, Huajun

    2013-01-01

    Highlights: • The R and D works for the ITER in-vessel coils (IVC) are now being conducted in Institute of Plasma Physics, and the analysis work are being done by Princeton Plasma Physics Laboratory. • There is little published paper about the raw materials for ITER IVC coils. • This manuscript points out the progress of the selected materials for ITER IVC coils. -- Abstract: The ITER in-vessel coils (IVCs) consist of 27 coils edge localized modes (ELM) and 2 coils vertical stabilization (VS) which are all mounted on the vacuum vessel wall behind the shield modules. The IVCs design and manufacturing work is being conducted in between Institute of Plasma Physics Chinese Academy of Sciences (ASIPP) and Princeton Plasma Physics Laboratory (PPPL). Because the position of ELM and VS coils is close and face to the plasma, the IVCs must undergo a severe environment, such as the high dose of radiation and high operation temperature, thus the conventional electrical insulation materials cannot be used. And the technology of “Stainless Steel Jacketed Mineral Insulated Conductor” (SSMIC) is deemed as the best choice to provide the necessary radiation resistance and compatibility strength in ITER's vacuum vessel. While mineral insulated conductor technology is not new, and is similar to the mineral insulated cable used in industrial. Some difficulties still need to be solved, such as searching for the proper raw-materials to make sure that the conductor have the properties of high current carrying capability, the necessary radiation resistance, the proper strength, at the same time, it must be come true in manufacture technology. This paper described the analysis of the materials for VS and ELM coil conductor

  14. Preparation and optimization of thermoelectric properties of Bi2Te3 based alloys using the waste particles as raw materials from the cutting process of the zone melting crystal rods

    Xiang, Qiusheng; Fan, Xi'an; Han, Xuewu; Zhang, Chengcheng; Hu, Jie; Feng, Bo; Jiang, Chengpeng; Li, Guangqiang; Li, Yawei; He, Zhu

    2017-12-01

    The p-type Bi2Te3 alloys were prepared using the waste particles from the cutting process of the zone melting crystal rods as the main raw materials by impurity removal process including washing, carbon monoxide reduction and vacuum metallurgical process. The thermoelectric properties of the Bi2Te3 based bulk materials were optimized by component adjustment, second smelting and resistance pressing sintering (RPS) process. All evidences confirmed that most of impurities from the line cutting process and the oxidation such as Sb2O3, Bi2O3 and Bi2Te4O11 could be removed by carbon monoxide reduction and vacuum metallurgical process adopted in this work, and the recycling yield was higher than 97%. Appropriate component adjustment treatment was used to optimize the carrier content and corresponding thermoelectric properties. Lastly, a Bi0.36Sb1.64Te3 bulk was obtained and its power factor (PF) could reach 4.24 mW m-1 K-2 at 300 K and the average PF value was over 3.2 mW m-1 K-2 from 300 K to 470 K, which was equivalent with the thermoelectric performance of the zone melting products from high purity elements Bi, Te and Sb. It was worth mentioning that the recovery process introduced here was a simple, low-cost, high recovery rate and green recycling technology.

  15. Determination of Bacterial Pathogen in Foods for Export and their Raw Material

    Marambio, E.; Cordano, A. M.; Insunza, M.; Fernández, M.; Astorga, J. [Sección Microbiología de Alimentos, Instituto de Salud Pública de Chile (Chile)

    2005-01-15

    Chile is a South American country with an important fish and shellfish production. These products are some of the most important items for the economy of the country. From 1998 to 2001, Chile exported $1 137 625 788 of fish and shellfish. Statistics also show that frozen vegetables are fast becoming high on the food export list. During recent years (1998 to 2001) $223 312 248 worth of frozen vegetables were exported to different countries. This study was performed to trace the presence of pathogens in some of these Chilean foods to be exported: 97 samples of salmon and 84 samples of different frozen vegetables (asparagus, peas and corn) were analyzed in order to determine their levels of microbial contamination. Total bacteria counts (mesophilic aerobes bacteria), Escherichia coli, Staphylococcus aureus, Bacillus cereus, Clostridium perfringens, Salmonella spp. and Listeria monocytogenes were tested. Vibrio cholerae was tested only in salmon samples. The analysis of salmon samples showed that the raw material presented a very good quality. However, during the filleting process the fish was contaminated, presenting higher total bacteria counts. Only one of the 48 final product samples presented contamination with a pathogenic bacteria (Listeria monocytogenes (<100 cfu/g)). Frozen vegetable samples (raw material and final products) did not present any of the pathogen bacteria studied. The mesophilic aerobes bacteria counts were reduced during processing due to the effectiveness of the good manufacturing practices and the technological process used. (author)

  16. Determination of Bacterial Pathogen in Foods for Export and their Raw Material

    Marambio, E.; Cordano, A.M.; Insunza, M.; Fernández, M.; Astorga, J.

    2005-01-01

    Chile is a South American country with an important fish and shellfish production. These products are some of the most important items for the economy of the country. From 1998 to 2001, Chile exported $1 137 625 788 of fish and shellfish. Statistics also show that frozen vegetables are fast becoming high on the food export list. During recent years (1998 to 2001) $223 312 248 worth of frozen vegetables were exported to different countries. This study was performed to trace the presence of pathogens in some of these Chilean foods to be exported: 97 samples of salmon and 84 samples of different frozen vegetables (asparagus, peas and corn) were analyzed in order to determine their levels of microbial contamination. Total bacteria counts (mesophilic aerobes bacteria), Escherichia coli, Staphylococcus aureus, Bacillus cereus, Clostridium perfringens, Salmonella spp. and Listeria monocytogenes were tested. Vibrio cholerae was tested only in salmon samples. The analysis of salmon samples showed that the raw material presented a very good quality. However, during the filleting process the fish was contaminated, presenting higher total bacteria counts. Only one of the 48 final product samples presented contamination with a pathogenic bacteria (Listeria monocytogenes (<100 cfu/g)). Frozen vegetable samples (raw material and final products) did not present any of the pathogen bacteria studied. The mesophilic aerobes bacteria counts were reduced during processing due to the effectiveness of the good manufacturing practices and the technological process used. (author)

  17. Iron zircon pigment synthesis: Proposal of a mixing index for the raw materials mixtures

    Zumaquero, E.; Ortsb, M.J.; Sanz, V.; Mestre, S.

    2017-01-01

    Iron zircon coral pigments are very interesting from an industrial point of view because of their high colouring power and their stability at high temperatures. However, the pigment's synthesis is particularly troublesome due to its specific reaction mechanism. As an encapsulated pigment it becomes very important how the raw materials are distributed in the reaction mixture. To evaluate the effectiveness of the mixing process, it would be convenient to define a parameter, that is the mixing index, to estimate the degree of homogeneity of the system. In the current investigation, a mixing index is proposed derived from the power spectrum of Fourier transform of scanning electron microscope (SEM) images of the raw material mixture. Concretely, the number of pixels in a certain range of values in the image of the power spectrum, seems to behave relatively well as mixing index. This index allows us to distinguish between samples with different zirconia and iron oxide used as precursors. The proposed mixing index seems to be related to the colouring power of the final pigment when the synthesis generates enough zircon to encapsulate hematite particles. [es

  18. Conference on raw materials and jobs cost variation - Impact on wind turbine manufacturers and operators

    Chabot, Bernard; Falk, Thorsten; Braeuninger, Michael; Rehfeldt, Knud; Brand, Ruth; Buhr, Ingo de; Jenne, Markus

    2007-01-01

    In the framework of the 2007 Husum Wind exhibition, the French-German office for Renewable energies (OFAEnR) organised a side event on In the framework of this French-German exchange of experience, participants exchanged views on raw materials and jobs cost variations in the wind power industry in both countries. Its aim was to compare and analyse the French and German respective support systems to renewable energy sources. This document brings together the available presentations (slides) made during this event: 1 - Protecting wind energy tariffs against inflation effects: analysis and suggestions from the French experience (Bernard Chabot); 2 - Wind energy in Germany - Tariff structure in the EEG renewable energy law (Thorsten Falk); 3 - Wind energy competitiveness (Michael Braeuninge, Knud Rehfeldt); 4 - Influence of raw materials price rise on the production costs of ENERCON wind turbines maker (Ruth Brand); 5 - Presentation of the overall costs of an offshore wind energy project (Ingo de Buhr); 6 - Comparison between French and German tariffs profitability using a model wind farm: presentation of the pros and cons of both systems (Markus Jenne)

  19. Effect of ionising radiation on shelf life and potency of herbal raw materials

    Rama Bhat, P.; Prajna, P.S.; Sanjeev, Ganesh; Padyana, Subramanya; Maurya, D.K.

    2013-01-01

    Medicinal herbs are involving from fringe to mainstream use with a greater number of people seeking remedies and health approaches free from side effects caused by synthetic chemicals. Unfortunately, the number of reports of people experiencing negative effects, caused by the use of herbal drugs, has also been increasing. There may be various reasons for such problems, poor quality of herbal medicines due to insufficient attention being paid to the quality assurance and control of these products. Plants are associated with their own microflora, in addition to that soil and air act as main inoculum source for causing contamination in crude herbs along with other field practices like harvesting, handling and packing. The study was aimed to determine the type, level of bacterial and fungal load and feasibility of electron beam irradiation to hygenise the commonly used herbal raw materials using electron beam radiation with three different dosages viz., 8 kGy, 12 kGy, 15 kGy. Irradiated and control samples were analysed for microbial load and biochemical compositions. In present study, microbial load was proportionately reduced with increase in dosage compared to non-irradiated samples. Results indicated that non-irradiated samples were highly contaminated with microbial load. E. coli and Staphylococcus spp. were predominant among the bacterial contaminants at varying levels. The fungi enumerated from raw materials includes species of Penicillium, Rhizopus, Mucor and Aspergillus. Minimum variation was recorded in the carbohydrate, protein, phenolic, tannin and ascorbic acid content of the herb samples with irradiation treatment. (author)

  20. Present and future trends in pellet markets, raw materials, and supply logistics in Sweden and Finland

    Selkimaeki, Mari; Mola-Yudego, Blas; Roeser, Dominik; Prinz, Robert; Sikanen, Lauri

    2010-01-01

    Wood pellets have become an important fuel in heat and power production, and pellet markets are currently undergoing rapid development. In this paper, the pellet markets, raw materials and supply structures are analyzed for Sweden and Finland, based on a database of the current location and production capacity of the pellet producers, complemented with existing reports and literature. In Sweden, a total of 94 pellet plants/producers were identified, producing 1.4 million tonnes of pellets, while the domestic consumption was 1.7 million tonnes, and about 400,000 t of pellets were imported to fulfil the demand in 2007. In Finland, 24 pellet plants/producers were identified and the production was around 330,000 t while the domestic consumption was 117,000 t in 2007. In Finland, pellet market has been long time export oriented, whereas domestic consumption has been growing mainly in the small scale consumer sector, estimated 15,000 households had pellet heating systems in 2008. In the future, the increasing number of pellet users will require a reliable delivery network and good equipment for bulk pellet deliveries. Provision of new raw materials and ensuring the good quality of pellets through the whole production, delivery and handling chain will be fundamental in order to increase the use of pellets and sustain the ability to compete with other fuels. (author)

  1. Nuclear raw materials. Knowledge status after the Geneva conference (September 1958)

    Lecoq, M.; Mabile, J.; Carrat, G.; Ginocchio, A.; Roques, E.; Waynbaum, M.; Chervet, J.; Branche, G.; Geffroy, J.; Le Goff, M.

    1959-05-01

    The authors propose a synthesis of the numerous contributions presented at the Geneva conference. They first address deposits: uranium deposits (studies on uranium geochemistry and metallogeny, descriptions of various deposit types such as those associated with sedimentary layers or tectonic structures or petrographic types), thorium deposits, beryllium deposits, zirconium deposits. A second part addresses research methods and equipment: descriptive mineralogical studies, analytic physical or chemical methods, analytic field methods, isotope analysis, prospecting methods (geochemical techniques, radiometry, geophysical methods, general remarks on prospecting methods, organization of prospecting operations, and techniques of deep prospecting). The third part addresses the issues of reserves and resources: definitions, assessment techniques, geographical distribution of reserves and resources. The fourth part addresses the exploitation: quarries, underground exploitation, measures for personnel protection. The fifth part addresses ore concentration: determination of uranium ore and other raw material, concentration by physical means, ore concentration by chemical means, ore sampling, and plant monitoring and regulation. The last part addresses the economy of raw materials: uranium (cost price and production, and purchase and selling prices in different countries, world market in 1960 and on a longer term), thorium, beryllium, zirconium, lithium and helium

  2. THE INFLUENCE OF RAW MATERIAL ON THE LIQUID MOISTURE TRANSPORT THROUGH KNITTED FABRIC

    COLDEA Alina

    2014-05-01

    Full Text Available The comfort is undoubtedly the most important human attribute depends upon the moisture transport which in turn depends on the moisture transport behavior of the knitted fabric. Moisture transport is the transfer of liquid water capillary interstices of the yarns and depends on the wettability of fiber surfaces, as well as the structure of the yarn and fabric. Because of its good water absorption property, cotton is often used for next-to-skin wear such as t-shirts, underwear, socks. All these are known as ``moisture management`` which means the ability of a textile fabric to transport moisture away from the skin to the garment’s outer surface in multi-dimensions and it is one of the key performance criteria in today’s apparel industry since it has a significant effect on the human perception of moisture sensations. In order to study, plated knitted fabric for socks were knitted as plated single jersey in the same production conditions, from different types of yarns, produced in different yarn counts (Ne 20, Ne 24, Ne 30 and different raw material. (cotton, bamboo, soybean, polyester, viscose. Were chose two different density on circular knitting machine. The liquid moisture management of the samples was measured in order to determinate moisture transport index. Was study also the influence of raw material and fabric structure related to the moisture transport index. According to the obtained results, it was found that some of the knitted fabrics used in this study have goodmoisture management capability.

  3. Quantitative analysis of the 26 allergens for cosmetic labeling in fragrance raw materials and perfume oils.

    Leijs, Hans; Broekhans, Joost; van Pelt, Leon; Mussinan, Cynthia

    2005-07-13

    The adoption of the 7th amendment of the European Cosmetic Directive 76/768/EEC requires any cosmetic product containing any of 26 raw materials identified by the Scientific Committee on Cosmetic Products and Non-Food Products intended for Consumers as likely to cause a contact allergy when present above certain trigger levels to be declared on the package label. Of these 26, 24 are volatile and can be analyzed by GC. This paper describes a method for the quantitative analysis of these volatile raw materials in perfume ingredients as well as complex perfume compositions. The method uses sequential dual-column GC-MS analysis. The full-scan data acquired minimize the false-positive and false-negative identifications that can be observed with alternate methods based on data acquired in the SIM mode. For each sample, allergen levels are determined on both columns sequentially, leading to two numerical results for each allergen. Quantification limits for each allergen in a perfume mixture based on the analysis of a standard are 0.999) and stable for multiple days. Studies on perfumes spiked with multiple allergens at 30, 50, and 70 mg/kg show recoveries close to nominal values.

  4. Evaluation of the biodiesel production using three sources of raw material and ethanol

    Radecki, Angela Patricia; Fracaro, Cristiane; Gnoatto, Estor; Kavanagh, Edward; Anami, Marcelo Hidemassa; Fischborn, Marcos; Lobo, Viviane da Silva [Universidade Tecnologica Federal do Parana (UTFPR), Medianeira, PR (Brazil)], E-mail: mhanami@utfpr.edu.br; Zara, Ricardo Fiori [Prati Donaduzzi e Cia. Ltda., Toledo, PR (Brazil)

    2008-07-01

    The conversion of different oils in ethyl ester (biodiesel) through the transesterification with anhydrous ethanol, together with its quality and its consumption in mixture with diesel of petroleum in different ratios, they were evaluated using a stationary diesel engine connected to an electric energy generator. The raw materials used in this transformation were oil of refined soybean, oil of refined sunflower and animal fat (swine). In the transesterification reaction it was used an alkaline catalyst (sodium hydroxide), because of its proven effectiveness and the high speed facing other catalyst, beyond being less corrosive and demands less molar' reasons between the alcohol and the vegetal oil. The tests in stationary diesel engine were carried through the dilutions of 0%, 5%, 10%, 15% and 20% of biodiesel produced in mixture with diesel of petroleum. The results showed that the yield of biodiesel gotten by different sources is satisfactory. It was also observed that the basic catalysis is adjusted to the production of biodiesel from raw materials with low acidity. The tests in diesel engine appeared to be sufficiently satisfactory once it was not observed any alteration in the functioning of the engine. The consumption was also not modified by the studied dilutions, demonstrating that the biodiesel can be added to the pure diesel reducing the use of the fuel derived from petroleum. (author)

  5. Gamma activity as a guide for the building raw materials selection and controlling the environmental hazards

    T. Ibrahim

    2012-06-01

    Full Text Available The spectrometric measurements can provide an alarm for the radiation activity and radioelement concentra-tions. The activity increase over the ambient background can be achieved by well calibrated gamma-spectrometers. In comparison between Wadi El-Dahl and Abu Zawal quarries for building raw materials (feld-spar, the activity concentration of El-Dahl stream sediments are 54.5 and 44.5 Bq/kg for uranium and thorium respectively. While the activity concentration of Abu Zawal rock quarry are 167.03 and 79.77 Bq/kg for uranium and thorium respectively. These activities yielding effective dose rates of 0.63 mSv/y for Wadi El-Dahl stream sediments and 1.48 mSv/y for Abu Zawal rock quarry. In summary, the spectrometric measurements are excellent selective tool to monitoring the environment against the radiation risk. In this aspect, Wadi El-Dahl stream sedi-ment quarry considered as the more suitable for producing feldspar as a raw materials to building industry. In comparison, Abu Zawal rock quarry has a higher effective dose rate exceeds the international permissible limits which is 1 mSv/y. A total of 19 feldspar samples were completely described regarding their general chemical fea-tures by using x-ray fluorescence. From the study all the samples contain high concentration of barium and ru-bidium which can separate using different methods in order to use in different important industry.

  6. Comparative study of the UV spectra of various raw materials OF Urtica dioica L.

    E. A. Balagozyan

    2016-01-01

    Full Text Available Stinging nettle (Urtica dioica L. is one of the famous and popular medicinal plants. In Russia the herbal materials are nettle’s leaves which have haemostatic effect. At the same time abroad the rhizomes and roots of nettle are the source of drugs with antitumor activity. The chemical composition of the rhizomes and roots of nettle is quite complicated and is represented by substances such as polysaccharides, lectins, sterols etc. The aim of the present study is the comparative phytochemical research of various parts of raw nettle by spectrophotometry. The study of extracts from various raw materials of nettle has shown, that the presence of flavonoids is peculiar for leaves, flowers and fruits. Sterols dominate in the rhizomes and roots of nettle. It was also noted that the UV-spectra of extracts of female inflorescences and fruits nettle have the same absorption maxima.

  7. Determination of Au, Pt, Pd in gold ore mineral raw materials by stripping voltammetry

    Kolpakova N.A.

    2016-01-01

    Full Text Available The paper considers the possibilities of use of the method of stripping voltammetry for finding platinum metals in mineral gold and ore raw material. A review of new options of electro-concentration of platinum metals on the surface of graphite electrode with the following sediment electro-oxidation and receipt of an analytical signal is presented: platinum finding was carried out by picks of selective electro-oxidation of iridium from intermetallic compound with platinum; gold finding was carried out by picks of gold electro-oxidation on the surface of graphite electrode modified by bismuth; palladium finding was performed by picks of palladium electro-oxidation on the surface of graphite electrode. 1M HCL solution was selected as a supporting electrolyte. Gold and hydrogen elimination on the process of palladium electro-oxidation was performed by means of UV irradiation of solution in the process of electro-concentration of palladium sediment. Gold, platinum and palladium determination was carried out in mineral gold and ore raw material of Verkhneamylskiy gold and ore district.

  8. Evaluation of Apple Pomace as a Raw Material for Alternative Applications in Food Industries

    Elena Falqué

    2007-01-01

    Full Text Available In order to measure the potential of apple pomace as a raw material for manufacturing food-related products (such as lactic acid, fiber-rich concentrates and pectin, samples from cider industry were assayed for composition and enzymatic digestibility. Alcohol-soluble compounds (monosaccharides, oligosaccharides and malic acid accounted for 32–45 mass percent of oven-dry pomace. Glucose and fructose were the major components of this fraction. The alcohol-insoluble fraction accounted for 55–68 mass percent of oven-dry pomace and was mainly made up of neutral detergent fiber (62–69 percent of the mass fraction and pectin (16.2–19.7 percent of the mass fraction. The feedstock content of N, P and metal ions (K, Mg, Fe and Mn was favourable for further manufacture of lactic acid fermentation media. Apple pomace showed a high susceptibility to enzymatic hydrolysis: in media with a cellulase loading of 8.5 FPU/g of apple pomace and a cellobiase loading of 5 IU/FPU, about 80 % of the total glucan was converted into glucose after 15 h. Considering the low enzyme charge, liquor to solid ratio employed, reaction time needed to achieve the maximal sugars concentration and N, P and metal ion (K, Mg, Fe and Mn content of samples, it can be concluded that apple pomace is a promising raw material for lactic acid production.

  9. Mathematical model of silicon smelting process basing on pelletized charge from technogenic raw materials

    Nemchinova, N. V.; Tyutrin, A. A.; Salov, V. M.

    2018-03-01

    The silicon production process in the electric arc reduction furnaces (EAF) is studied using pelletized charge as an additive to the standard on the basis of the generated mathematical model. The results obtained due to the model will contribute to the analysis of the charge components behavior during melting with the achievement of optimum final parameters of the silicon production process. The authors proposed using technogenic waste as a raw material for the silicon production in a pelletized form using liquid glass and aluminum production dust from the electrostatic precipitators as a binder. The method of mathematical modeling with the help of the ‘Selector’ software package was used as a basis for the theoretical study. A model was simulated with the imitation of four furnace temperature zones and a crystalline silicon phase (25 °C). The main advantage of the created model is the ability to analyze the behavior of all burden materials (including pelletized charge) in the carbothermic process. The behavior analysis is based on the thermodynamic probability data of the burden materials interactions in the carbothermic process. The model accounts for 17 elements entering the furnace with raw materials, electrodes and air. The silicon melt, obtained by the modeling, contained 91.73 % wt. of the target product. The simulation results showed that in the use of the proposed combined charge, the recovery of silicon reached 69.248 %, which is in good agreement with practical data. The results of the crystalline silicon chemical composition modeling are compared with the real silicon samples of chemical analysis data, which showed the results of convergence. The efficiency of the mathematical modeling methods in the studying of the carbothermal silicon obtaining process with complex interphase transformations and the formation of numerous intermediate compounds using a pelletized charge as an additive to the traditional one is shown.

  10. Ion irradiation effects on high purity bcc Fe and model FeCr alloys

    Bhattacharya, Arunodaya

    2014-01-01

    FeCr binary alloys are a simple representative of the reduced activation ferritic/martensitic (F-M) steels, which are currently the most promising candidates as structural materials for the sodium cooled fast reactors (SFR) and future fusion systems. However, the impact of Cr on the evolution of the irradiated microstructure in these materials is not well understood in these materials. Moreover, particularly for fusion applications, the radiation damage scenario is expected to be complicated further by the presence of large quantities of He produced by the nuclear transmutation (∼ 10 appm He/dpa). Within this context, an elaborate ion irradiation study was performed at 500 C on a wide variety of high purity FeCr alloys (with Cr content ranging from ∼ 3 wt.% to 14 wt.%) and a bcc Fe, to probe in detail the influence of Cr and He on the evolution of microstructure. The irradiations were performed using Fe self-ions, in single beam mode and in dual beam mode (damage by Fe ions and co-implantation of He), to separate ballistic damage effect from the impact of simultaneous He injection. Three different dose ranges were studied: high dose (157 dpa, 17 appm He/dpa for the dual beam case), intermediate dose (45 dpa, 57 appm He/dpa for dual beam case) and in-situ low dose (0.33 dpa, 3030 appm He/dpa for the dual beam case). The experiments were performed at the JANNuS triple beam facility and dual beam in situ irradiation facility at CEA-Saclay and CSNSM, Orsay respectively. The microstructure was principally characterized by conventional TEM, APT and EDS in STEM mode. The main results are as follows: 1) A comparison of the cavity microstructure in high dose irradiated Fe revealed strong swelling reduction by the addition of He. It was achieved by a drastic reduction in cavity sizes and an increased number density. This behaviour was observed all along the damage depth, up to the damage peak. 2) Cavity microstructure was also studied in the dual beam high dose

  11. Natural stone muds as secondary raw materials: towards a new sustainable recovery process

    Zichella, Lorena; Tori, Alice; Bellopede, Rossana; Marini, Paola

    2016-04-01

    The production of residual sludge is a topical issue, and has become essential to recover and reuse the materials, both for the economics and the environmental aspect. According to environmental EU Directives, in fact ,the stone cutting and processing should characterized by following objectives, targets and actions: the reduction of waste generated, the decreasing of use of critical raw material, the zero landfilling of sludge and decreasing in potential soil contamination, the prevention of transport of dangerous waste, the reduction of energy consumption, the zero impact on air pollution and the cost reduction . There are many industrial sector in which residual sludge have high concentrations of metals and/or elements deemed harmful and therefore hazardous waste. An important goal, for all industrial sectors, is an increase in productivity and a parallel reduction in costs. The research leads to the development of solutions with an always reduced environmental impact. The possibility to decrease the amount of required raw materials and at the same time the reduction in the amount of waste has become the aim for any industrial reality. From literature there are different approaches for the recovery of raw and secondary materials, and are often used for the purpose chemical products that separate the elements constituting the mud but at the same time make additional pollutants. The aim of the study is to find solutions that are environmentally sustainable for both industries and citizens. The present study is focused on three different Piedmont rocks: Luserna, Diorite from Traversella and Diorite from Vico, processed with three different stone machining technologies: cutting with diamond wire in quarry (blocks), in sawmill (slabs) and surface polishing. The steps are: chemical analysis, particle size analysis and mineralogical composition and characterization of the sludge obtained from the various machining operations for the recovery of the metal material by

  12. Towards a dynamic assessment of raw materials criticality: Linking agent-based demand — With material flow supply modelling approaches

    Knoeri, Christof; Wäger, Patrick A.; Stamp, Anna; Althaus, Hans-Joerg; Weil, Marcel

    2013-01-01

    Emerging technologies such as information and communication-, photovoltaic- or battery technologies are expected to increase significantly the demand for scarce metals in the near future. The recently developed methods to evaluate the criticality of mineral raw materials typically provide a ‘snapshot’ of the criticality of a certain material at one point in time by using static indicators both for supply risk and for the impacts of supply restrictions. While allowing for insights into the mechanisms behind the criticality of raw materials, these methods cannot account for dynamic changes in products and/or activities over time. In this paper we propose a conceptual framework intended to overcome these limitations by including the dynamic interactions between different possible demand and supply configurations. The framework integrates an agent-based behaviour model, where demand emerges from individual agent decisions and interaction, into a dynamic material flow model, representing the materials' stocks and flows. Within the framework, the environmental implications of substitution decisions are evaluated by applying life-cycle assessment methodology. The approach makes a first step towards a dynamic criticality assessment and will enhance the understanding of industrial substitution decisions and environmental implications related to critical metals. We discuss the potential and limitation of such an approach in contrast to state-of-the-art methods and how it might lead to criticality assessments tailored to the specific circumstances of single industrial sectors or individual companies. - Highlights: ► Current criticality assessment methods provide a ‘snapshot’ at one point in time. ► They do not account for dynamic interactions between demand and supply. ► We propose a conceptual framework to overcomes these limitations. ► The framework integrates an agent-based behaviour model with a dynamic material flow model. ► The approach proposed makes

  13. Life cycle assessment of sustainable raw material acquisition for functional magnetite bionanoparticle production.

    Sadhukhan, Jhuma; Joshi, Nimisha; Shemfe, Mobolaji; Lloyd, Jonathan R

    2017-09-01

    Magnetite nanoparticles (MNPs) have several applications, including use in medical diagnostics, renewable energy production and waste remediation. However, the processes for MNP production from analytical-grade materials are resource intensive and can be environmentally damaging. This work for the first time examines the life cycle assessment (LCA) of four MNP production cases: (i) industrial MNP production system; (ii) a state-of-the-art MNP biosynthesis system; (iii) an optimal MNP biosynthesis system and (iv) an MNP biosynthesis system using raw materials sourced from wastewaters, in order to recommend a sustainable raw material acquisition pathway for MNP synthesis. The industrial production system was used as a benchmark to compare the LCA performances of the bio-based systems (cases ii-iv). A combination of appropriate life cycle impact assessment methods was employed to analyse environmental costs and benefits of the systems comprehensively. The LCA results revealed that the state-of-the-art MNP biosynthesis system, which utilises analytical grade ferric chloride and sodium hydroxide as raw materials, generated environmental costs rather than benefits compared to the industrial MNP production system. Nevertheless, decreases in environmental impacts by six-fold were achieved by reducing sodium hydroxide input from 11.28 to 1.55 in a mass ratio to MNPs and replacing ferric chloride with ferric sulphate (3.02 and 2.59, respectively, in a mass ratio to MNPs) in the optimal biosynthesis system. Thus, the potential adverse environmental impacts of MNP production via the biosynthesis system can be reduced by minimising sodium hydroxide and substituting ferric sulphate for ferric chloride. Moreover, considerable environmental benefits were exhibited in case (iv), where Fe(III) ions were sourced from metal-containing wastewaters and reduced to MNPs by electrons harvested from organic substrates. It was revealed that 14.4 kJ and 3.9 kJ of primary fossil resource

  14. From basic raw material goods to cultural and environmental services: the Chinese bamboo sophistication path

    Manuel Ruiz Pérez

    2014-12-01

    Full Text Available Bamboo has deep cultural and economic roots in China, the country with the largest bamboo resources in the world. Over the last three decades bamboo has evolved from a supply of raw material for basic goods into the material base of an increasingly diversified array of products and, more recently, into a potentially important source of cultural and environmental services. Based on a general literature review and the lessons learned from detailed case studies in different regions of China, we explored the changing roles of bamboo, and its effects on local economies and farmers' livelihood strategies. As the country develops and new economic activities continue to appear, bamboo production has shifted from a superior income-generating opportunity that largely benefited the better-off to a less attractive option left for those who have no other choice. The nature of the work has also changed, from families working directly on their bamboo plots to an emphasis on hired labor, with prosperous bamboo owners devoting most of their time to more lucrative activities. A similar process can be observed in bamboo processing in counties where previous industrial structures hinged around raw material harvests, but which have now entered into other secondary and tertiary industry activities. At the same time, bamboo has attracted new opportunities as a source of cultural, aesthetic, and leisure-related activities, as well as some potentially important climatic, watershed, and biodiversity functions. We analyze the complementarity between goods and services provided by bamboo and discuss some research issues and future trends that may help in overcoming these conflicts.

  15. Crystallographic Analysis of Nucleation at Hardness Indentations in High-Purity Aluminum

    Xu, Chaoling; Zhang, Yubin; Lin, Fengxiang

    2016-01-01

    Nucleation at Vickers hardness indentations has been studied in high-purity aluminum cold-rolled 12 pct. Electron channeling contrast was used to measure the size of the indentations and to detect nuclei, while electron backscattering diffraction was used to determine crystallographic orientations....... It is found that indentations are preferential nucleation sites. The crystallographic orientations of the deformed grains affect the hardness and the nucleation potentials at the indentations. Higher hardness gives increased nucleation probabilities. Orientation relationships between nuclei developed...... they form. Finally, possible nucleation mechanisms are briefly discussed....

  16. A fundamental self-generated quenching center for lanthanide-doped high-purity solids

    Auzel, F.

    2002-01-01

    An intrinsic self-generated quenching center for lanthanide-doped high-purity solids is presented for transitions, which cannot be quenched by cross-relaxation. This center, in fact a cluster-like pair of active centers, is shown to come from a particular multiphonon-assisted energy transfer between them. Being due to the vibronic properties of the host it cannot be suppressed. Its role in lanthanide first excited states self-quenching is analyzed and a simple mathematical expression is derived. This law is compared with experimental results for self-quenching in Er-doped fluorophosphate glasses

  17. Synthesis and characterization of straight and stacked-sheet AlN nanowires with high purity

    Lei, M.; Yang, H.; Li, P.G.; Tang, W.H.

    2008-01-01

    Large-scale AlN nanowires with hexagonal crystal structure were synthesized by the direct nitridation method at high temperatures. The experimental results indicate that these single-crystalline AlN nanowires have high purity and consist of straight and stacked-sheet nanowires. It is found that straight AlN nanowire grows along [1, 1, -2, 0] direction, whereas the stacked-sheet nanowire with hexagonal cross section is along [0 0 0 1] direction. It is thought that vapor-solid (VS) mechanism should be responsible for the growth of AlN nanowires

  18. Damage process of high purity tungsten coatings by hydrogen beam heat loads

    Tamura, S.; Tokunaga, K.; Yoshida, N.; Taniguchi, M.; Ezato, K.; Sato, K.; Suzuki, S.; Akiba, M.; Tsunekawa, Y.; Okumiya, M.

    2005-01-01

    To investigate the synergistic effects of heat load and hydrogen irradiation, cyclic heat load tests with a hydrogen beam and a comparable electron beam were performed for high purity CVD-tungsten coatings. Surface modification was examined as a function of the peak temperature by changing the heat flux. Scanning Electron Microscopy analysis showed that the surface damage caused by the hydrogen beam was more severe than that by the electron beam. In the hydrogen beam case, cracking at the surface occurred at all peak temperatures examined from 300 deg. C to 1600 deg. C. These results indicate that the injected hydrogen induces embrittlement for the CVD-tungsten coating

  19. An ICP AES method for determination of dysprosium and terbium in high purity yttrium oxide

    Rupawate, V.H.; Hareendran, K.N.; Roy, S.B.

    2011-01-01

    High purity yttrium finds interesting application in astronavigation, luminescence, nuclear energy and metallurgical industries. Most of these applications require yttrium oxide of highest purity. Consequently there is a need for production of high purity yttrium oxide. Separation and purification of yttrium from other rare earths is a challenging task due to their close chemical properties. Liquid-liquid extraction and ion exchange have been widely used in the production of yttrium oxide of highest purity. Determination of impurities, especially other rare earths, in ppm level is required for process development and chemical characterization of the high purity Y 2 O 3 . Many methods have been described in literature. However since the advent of ICP AES much work in this area has been carried out by this technique. This paper describes the work done for determination of dysprosium (Dy) and terbium (Tb) in yttrium oxide using a high resolution sequential ICP AES. Emission spectra of rare earth elements are very complex and due to this complexity it is important to select spectral interference free analyte lines for determination of rare earths in rare earth matrix. For the determination of Dy and Tb in Y 2 O 3 , sensitive lines of Dy and Tb are selected from the instrument wavelength table and spectral interference free emission lines for the determination is selected by scanning around the selected wavelengths using 5 g/L Y solution and 5 mg/L standard solutions of Dy and Tb prepared in 4% nitric acid. It is found 353.170 nm line of Dy and 350.917 nm line Tb is suitable for quantitative determination. The signal to background ratio increases with increase in matrix concentration, i.e. from 1 to 5 mg/L. The optimum forward power is determined and it is found to be 1100W for Dy and 1000W for Tb. The instrument is calibrated using matrix matched standards containing 5g/L of Y matrix. Samples are dissolved in nitric acid and Y concentration is maintained at 5g/L. Two

  20. Amorphous germanium as an electron or hole blocking contact on high-purity germanium detectors

    Hansen, W.L.; Haller, E.E.

    1976-10-01

    Experiments were performed in an attempt to make thin n + contacts on high-purity germanium by the solid phase/sup 1)/ epitaxial regrowth of arsenic doped amorphous germanium. After cleaning the crystal surface with argon sputtering and trying many combinations of layers, it was not found possible to induce recrystallization below 400 0 C. However, it was found that simple thermally evaporated amorphous Ge made fairly good electron or hole blocking contacts. Excellent spectrometers have been made with amorphous Ge replacing the n + contact. As presently produced, the amorphous Ge contact diodes show a large variation in high-voltage leakage current

  1. Hysec Process: production of high-purity hydrogen from coke oven gas

    Nishida, S

    1984-01-01

    An account is given of the development of the Hysec Process by the Kansai Netsukagaku and Mitsubishi Kakoki companies. The process is outlined and its special features noted. The initial development aim was to obtain high-purity hydrogen from coke oven gas by means of PSA. To achieve this, ways had to be found for removing the impurities in the coke oven gas and the trace amounts of oxygen which are found in the product hydrogen. The resulting hydrogen is 99.9999% pure. 3 references.

  2. Ion-exchange preparation of high-purity vanadium acid from industrial liquors

    Sajdakhmedov, U.A.; Arslanov, Sh.S.; Vulikh, A.I.

    1994-01-01

    The results of investigations on production of special-purity vanadium acid and vanadium oxide directly from process solutions (technical grade liquors) using ionites are presented. Potentiality of thorough purification of vanadium(5) oxide, when producing vanadium acid on the KU-2 cationite with subsequent purification on anionite, is shown. On the basis of the results obtained a principle flowsheet of ion-exchange production of high-purity vanadium(5) oxide from industrial liquors has been developed. 2 refs.; 1 fig.; 4 tabs

  3. High-precision efficiency calibration of a high-purity co-axial germanium detector

    Blank, B., E-mail: blank@cenbg.in2p3.fr [Centre d' Etudes Nucléaires de Bordeaux Gradignan, UMR 5797, CNRS/IN2P3, Université de Bordeaux, Chemin du Solarium, BP 120, 33175 Gradignan Cedex (France); Souin, J.; Ascher, P.; Audirac, L.; Canchel, G.; Gerbaux, M.; Grévy, S.; Giovinazzo, J.; Guérin, H.; Nieto, T. Kurtukian; Matea, I. [Centre d' Etudes Nucléaires de Bordeaux Gradignan, UMR 5797, CNRS/IN2P3, Université de Bordeaux, Chemin du Solarium, BP 120, 33175 Gradignan Cedex (France); Bouzomita, H.; Delahaye, P.; Grinyer, G.F.; Thomas, J.C. [Grand Accélérateur National d' Ions Lourds, CEA/DSM, CNRS/IN2P3, Bvd Henri Becquerel, BP 55027, F-14076 CAEN Cedex 5 (France)

    2015-03-11

    A high-purity co-axial germanium detector has been calibrated in efficiency to a precision of about 0.15% over a wide energy range. High-precision scans of the detector crystal and γ-ray source measurements have been compared to Monte-Carlo simulations to adjust the dimensions of a detector model. For this purpose, standard calibration sources and short-lived online sources have been used. The resulting efficiency calibration reaches the precision needed e.g. for branching ratio measurements of super-allowed β decays for tests of the weak-interaction standard model.

  4. Measurement of oxide-layer thickness of internal granules in high-purity aluminium

    Takacs, S.; Ditroi, F.; Mahunka, I.

    1989-01-01

    Charged-particle activation analysis was used for the determination of bulk oxygen concentration in aluminium. High-purity aluminium samples and mixtures containing different amounts of alumina were irradiated by 13 MeV 3 He particles. The aim of the investigation was to determine the oxide-layer thickness on the surface of internal aluminium granules. The measurement was carried out by determining the bulk oxygen concentration in the samples, and calculating the oxide-layer thickness, by using model conditions about the microstructure of the aluminium samples. (author) 5 refs

  5. Comparison of Response Characteristics of High-Purity Germanium Detectors using Analog Versus Digital Processing

    Luke, S J; Raschke, K

    2004-01-01

    In this article we will discuss some of the results of the response characteristics of High Purity germanium detectors using analog versus digital processing of the signals that are outputted from the detector. The discussion will focus on whether or not there is a significant difference in the response of the detector with digital electronics that it limits the ability of the detection system to get reasonable gamma ray spectrometric results. Particularly, whether or not the performance of the analysis code Pu600 is compromised

  6. Formation and evolution of tweed structures on high-purity aluminum polycrystalline foils under cyclic tension

    Kuznetsov, P. V.; Vlasov, I. V.; Sklyarova, E. A.; Smekalina, T. V.

    2015-01-01

    Peculiarities of formation and evolution of tweed structures on the surface of high-purity aluminum polycrystalline foils under cyclic tension were studied using an atom force microscope and a white light interferometer. Tweed structures of micron and submicron sizes were found on the foils at different number of cycles. In the range of 42,000 < N < 95,000 cycles destruction of tweed patterns is observed, which leads to their disappearance from the surface of the foils. Formation of tweed structures of various scales is discussed in terms of the Grinfeld instability

  7. Towards more efficient raw material and water use in the production of fine art paper

    Pitkaenen, M. [Metsae-Serla Oyj, Aeaenekoski (Finland)

    1999-07-01

    Metsae-Serla's Aeaenekoski paper mill produces triple coated fine paper. The production capacity is 150000 t/a and the grammage range from 115 to 280 g/m{sup 2}. About 70% is sheeted at the mill. Profitability of the mill has been systematically improved. Among other things a good on-process wet end control system has been built. Raw material optimization has been done. The target of this two-year development project was to produce an optimized total plan for the raise of the closure degree based on critical examination of the whole paper making process. As a concrete target was a feasible plan how to cut the raw material losses to the effluent by 50% and the consumption of chemical water by 30%. The final target was significant annual cost savings. The project was run as three parallel sub-projects and total optimization was made simultaneously. The mill had two effluent flows; one for fibre containing and one for coating colour waste waters. Survey of both streams was carried out and the sources, amounts and quality of the fractions were determined. The lost raw material was 550 t/ month. One half was lost in the fibre and the other in the coating colour containing waste waters. Technical and economic evaluations were carried out for a proceeding plan. After tests and laboratory and pilot trials FilRec disperser was chosen as the treatment technique for the hydro cyclone reject and ultrafiltration for the recovery of coating colour. The specific consumption of chemical water was 9.1 m{sup 3}/ coated tonne. In the second sub-project a critical survey of the various uses was carried out. Quality demands for the chemical dilution purposes were studied by laboratory tests. Process chemical optimization was carried out. The effect of increasing closure on charge and COD build up was simulated using WinGEMS software. Possible solutions to replace chemical water and reduce its need were considered against the consequent investment costs. A proceeding plan for

  8. Characterization of raw materials and manufactured binderless particleboard from oil palm biomass

    Hashim, Rokiah; Nadhari, Wan Noor Aidawati Wan; Sulaiman, Othman; Kawamura, Fumio; Hiziroglu, Salim; Sato, Masatoshi; Sugimoto, Tomoko; Seng, Tay Guan; Tanaka, Ryohei

    2011-01-01

    The objective of this study was to examine the extractive, holocellulose, alpha cellulose, lignin, starch, and sugar contents of oil palm biomass and to evaluate its suitability in binderless particleboard production. In this study, bark, leaves, fronds, mid-parts and core-parts of the trunks were used to produce experimental binderless particleboard panels. Binderless particleboard panels were made with a target density of 0.80 g/cm 3 at a temperature of 180 o C and a pressure of 12 MPa in a computer controlled hot press. The modulus of rupture, the internal bond strength, the thickness swelling and the water absorption of the panels were evaluated. Fourier transform infrared spectroscopy and field emission scanning electron microscopy were used to characterize the properties of the raw materials and the manufactured panels. The chemical composition of the oil palm biomass consisted of high holocellulose, lignin, starch and sugar contents that have been found to aid in the production of binderless particleboard. The core-part of the trunk contained the highest amount of starch and total sugar. Samples made from the core-parts and fronds had sufficient modulus of rupture and internal bond strength to meet the Japanese Industrial Standard. The internal bond strength of the mid-part panels also met the standard. However, binderless board prepared from bark and leaves showed poor modulus of rupture and internal bond strength. Samples from the core-parts had the lowest thickness swell and water absorption but did not meet the above standard. The Fourier transform infrared spectroscopy spectra did not show any substantial difference between the raw materials and the manufactured panels. Field emission scanning electron microscopy indicated that the compressed cells varied between raw material types and showed the presence of compressed cells with some starch granules that facilitated adhesion. Based on the findings of this study, oil palm has the potential to be used to

  9. Applications of INAA with Ghent k0 factors to the analysis of high-purity metals and ceramics

    Erdtmann, G.; Petri, H.; Kaysser, B.; Kueppers, G.

    1988-01-01

    Reactor neutron activation analysis (NAA) has been applied for many years in the chemical-analytical service carried out by the Central Division of Chemical Analysis at Kernforschungsanlage Julich. At this research center, two new research programs were started in 1986: high-temperature-resistant materials and structure ceramics, and basic research for information technology. Trace element analyses of materials are required for both programs, and the demand for activation analyses has largely increased. In most cases they are carried out by a purely instrumental technique, and radiochemical NAA is applied but with some special problems. Activation analyses have been carried out for a number of high-purity and ceramic materials, and the paper shows detection limits obtained with some of them. The differences in detection limits depend not only on the types of materials and the levels of impurities but also on the irradiation and counting conditions chose. In order to obtain realistic estimations of the uncertainties of the results, all sources of error have been considered and their influence on total uncertainties calculated via the error propagation law applied to the equation of absolute activation analysis

  10. Taking the Step towards a More Dynamic View on Raw Material Criticality: An Indicator Based Analysis for Germany and Japan

    Simon Glöser-Chahoud

    2016-12-01

    Full Text Available Due to mounting concerns about the security of raw material supplies, numerous studies dealing with the quantification of supply risks and material criticality at the national level have been carried out in previous years. Regarding these studies, most approaches are indicator based static screening methods analyzing large numbers of raw materials and identifying those which are most critical for an economy. The majority of these screening methods quantify supply risks and vulnerabilities for one base year without taking into account temporal changes. Dynamic approaches for specific raw materials analyzing affected value chains in detail have been introduced recently; however, these studies do not intend to provide a screening of larger numbers of commodities. In this paper, we present a simple dynamic screening approach to assess raw material criticality at the country level building upon methods from innovation economics. The indicators applied in this study are only based on broadly available production and trade data, which makes this approach relatively easy to apply. We test our methodology on the example of Germany and Japan—two economies with highly specialized industries and low domestic raw material deposits, and, hence, high import dependency. The results are comparable to those of previously conducted multi indicator based static screening methods. However, they provide additional insight into temporal developments over the previous decade.

  11. Some economic aspects of the conversion of raw materials into final products

    Pick, H J [Univ. of Aston, Birmingham, Eng.; Becker, P E

    1978-01-01

    In a previous paper Pick and Becker analyzed the direct and indirect relations between energy and the ''physical structure'' materials used by the engineering and construction industries. The present paper provides a more general description of materials conversion from natural resources to final products. The cost of raw materials, only some 30 percent of which come from the developing countries, accounts for a relatively small proportion of final product costs, the remaining product costs arising from the progressive application of labor, capital, energy, etc. Emphasis is placed on the complete interdependence of the inputs to manufacturing; a change in any one having implications for the remainder. Materials substitution, while in principle providing an adaptive mechanism to change, also has implications for a wide range of factors of production and for social and industrial issues such as regional employment, the demand for specific trades and professions, for research and development and for industrial structure and capital investment. Full allowance for this interdependence needs to be an integral part of effective long term policy formulation and of research and development planning.

  12. Influence of raw material properties on energy consumption during briquetting process

    Ivanova Tatiana

    2018-01-01

    Full Text Available Biomass is doubtless a very significant source of renewable energy being worldwide abundant with high energy potential. This paper deals with assessment energy consumption at especially grinding and briquetting processes, which should result in essential economy of energy at solid biofuel production. Various types of raw materials were used at the experiment such as hemp (Cannabis sativa L. biomass, two species of Miscanthus (Miscanthus sinensis, Miscanthus x gigantheus and apple wood biomass. These materials were dried, grinded and pressed by piston press having pressing chamber diameter of 65 mm. Materials were grinded into three fractions (4 mm, 8 mm and 12 mm. Material throughput (kg.h-1 and energy consumption (kWh.t-1 were registered. As to results: the highest throughput at both grinding cases as well as briquetting was found at apple wood biomass; however the energy consumption during briquetting of apple wood was relatively high. The worst results concerning throughput and energy consumption (especially at briquetting were found at hemp biomass. Nevertheless, briquettes made of hemp had the best mechanical durability. Both Miscunthus species (herbaceous biomass have very similar parameters and showed quite good relation between throughput and energy consumption at the used machines.

  13. Energies and raw materials. The energy situation; Energies et matieres premieres. Conjoncture energetique

    NONE

    1997-10-01

    Statistics are given on the energy and raw materials (coal, oil, etc.) production and consumption levels in France in October 1997: primary energy total consumption has increased (mobile year) of 0.8%, at the same rate since 3 years. Interior demand has varied depending on the energy: strong decrease for coal (- 8.1%), slight increase for petroleum products (+ 1.3%), slowing down increase for gas (+ 2.1%) and moderate increase for electricity (+ 1.4%). An increase in the dollar exchange rate and a high level of oil and gas imports have induced a high energy cost level with + 22% on one year, reaching 87.8 billions Francs, to be compared to 72.0 in October 1996

  14. Energies and raw materials. The energy situation; Energies et matieres premieres. Conjoncture energetique

    NONE

    1997-11-01

    Statistics are given on the energy and raw materials (coal, oil, etc.) production and consumption levels in France in November 1997: primary energy total consumption has increased (mobile year) of 0.6%, at a slightly inferior rate than the rate since 3 years. Interior demand has varied depending on the energy: strong decrease for coal (- 9.3%), slight increase for petroleum products (+ 1.2%), markedly slowing down increase for gas (+ 1.4%) and moderate increase for electricity (+ 1.3%). An increase in the dollar exchange rate and a high level of oil and gas imports have induced a maintained high energy cost level with + 14% on one year, reaching 86.8 billions Francs, to be compared to 76.1 in November 1996

  15. Energies and raw materials. The energy situation; Energies et matieres premieres. Conjoncture energetique

    NONE

    1997-09-01

    Statistics are given on the energy and raw materials (coal, oil, etc.) production and consumption levels in France in September 1997: primary energy total consumption has increased (mobile year) of 1.1%, at the same rate since 3 years. Interior demand has varied depending on the energy: strong decrease for coal (- 5.9%), slight increase for petroleum products (+ 0.8%), strong increase for gas (+ 3.2%) and moderate increase for electricity (+ 1.7%). An increase in the dollar exchange rate and a high level of oil and gas imports have induced a record energy cost level with + 30% on one year, reaching 89.2 billions Francs, to be compared to 68.5 in September 1996

  16. Recovery of uranium and molybdenum elements from gebel gattar raw material, eastern desert, Egypt. Vol. 3

    El-Hazek, N.T.; Mahdy, M.A.; Mahmoud, H.M.K.

    1996-01-01

    G. Gatter uranium mineralizations are located along the faults and fracture zones crossing G.Gattar granitic pluton and long the contact of the pluton with the hammamat sediments. Also, molybdenum id presented in more than one mode of occurrence. The molybdenum mineralization treated in this work is the dessimenated type. The uranium and molybdenum raw material was subjected to series of leaching experiments including acid and alkaline agitation, alkaline percolation, and acid heap leaching techniques. Recovery of uranium and molybdenum was achieved by anion-exchange method followed by their elution by acidified sodium chloride. Uranium precipitation was performed in the form of ammonium diuranate (Yellow Cake). On the other hand molybdenum was precipitated in the form of molybdenum oxide. A tentative flowsheet for the extraction of both uranium and molybdenum is proposed and discussed. 13 figs., 3 tabs

  17. Role of complex utilization of mineral raw materials In geological research

    Takacs, P.; Varju, G.

    1979-01-01

    Presents Hungarian research efforts on ways of utilizing the secondary raw materials alunite, pumice and slate coal from various mines. The slate coal is separated from brown coal and disposed of at spoil banks of brown coal mines, due to its high ash content (up to 56.8% under dry conditions), silicate content up to 58.2% and low calorific value between 1500 and 2780 kcal/kg. The research proposal for utilizing slate coal is directed at partial separation of the mineral and coal content by comminution, peptization and hydrocentrifugal separation. The larger part of the silicate content is held in the colloid suspension, which could be used for conditioning drilling mud or foundry sand. The produced coal concentrate has a reduced ash content and higher calorific value (between 500 and 800 kcal/kg) and could be employed in soil amelioration or combustion. (10 refs.) (In German)

  18. Cashew nut shell liquid, a valuable raw material for generating semiconductive polyaniline nanofibers

    Raiane Valenti Gonçalves

    2018-03-01

    Full Text Available Abstract Cashew nut shell liquid (CNSL is an abundant and renewable by-product of the cashew nut industry. It appears to be a valuable raw material for generating semiconductive polyaniline (PAni nanomaterial with enhanced thermal stability and well-defined nanofiber morphology following a polymerization dispersion process. This study confirms that CNSL acts as a soft template during PAni synthesis, leading to an improvement in the nanofiber aspect. CNSL also improves the thermal stability of the PAni nanomaterial. Moreover, CNSL is an effective surfactant that promotes and stabilizes the dispersion of PAni nanofibers within water, allowing the more ecofriendly preparation of PAni nanomaterial by substituting the commonly used organic solvent with aqueous media. Finally, although CNSL promotes the formation of the conductive emeraldine salt form of PAni, increasing CNSL concentrations appear to plasticize the PAni polymer, leading to reduced electrical conductivity. However, this reduction is not detrimental, and PAni nanofibers remain semiconductive even under high CNSL concentrations.

  19. Microbial decontamination of cosmetic raw materials and personal care products by irradiation

    Katusin-Razem, B.; Mihaljevic, B.; Razem, D.

    2005-01-01

    Typical levels of sporadically occurring (dynamic) microbial contamination of cosmetic raw materials: pigments, abrasives and liposomes, as well as of final products for personal care, i.e. toothpaste, crayons, shampoos, cleansers and creams, were evaluated. In most cases, contamination was dominated by a single population of microorganisms, either Gram-negative bacteria or molds. The feasibility of microbial decontamination by irradiation was studied by determining the resistance to gamma radiation of contaminating microflora in situ. It was expressed as a dose required for the first 90% reduction, D first 9 0% red. The values in the range 1-2 kGy for molds and 0.1-0.6 kGy for Gram-negative bacteria were obtained. This relatively high susceptibility to irradiation allowed inactivation factors close to 6 to be achieved with doses generally not exceeding 3 kGy, and yielding endpoint contamination less than 10 g -1 . (author)

  20. Nuclear raw materials prospection mission 1965 report to the Government of the Republic Oriental del Uruguay

    Cameron, J

    1966-07-01

    A preliminary reconnaissance survey of Uruguay for nuclear raw materials has been completed. Over 7.700 kilometers have been surveyed by car borne scintillometer and 112 radioactive anomalies have been discovered. Favourable areas with high incidence of anomalies and indications of uranium occurrences have been de-limited in the Minas- Aigua, Valentines-Treinta y Tres, Las Canas, Minas de Corrales and Melo areas. A possibly important indication of uranium at Paso de Las Piedras, Department of Durazno, has also 'been discovered by other means.The area investigated only comprises 0.83 of the total area of Uruguay and the high incidence of anomalies discovered and the other indications of uranium within this area are favourable and encouraging factors for further work,.